WorldWideScience

Sample records for model year passenger

  1. Relationship Between Vehicle Size and Fatality Risk in Model Year 1985-93 Passenger Cars and Light Trucks

    Science.gov (United States)

    1997-01-01

    Fatality rates per million exposure years are computed by make, model and model year, : based on the crash experience of model year 1985-93 passenger cars and light trucks (pickups) vans : and sport utility vehicles) in the United States during calen...

  2. Validating the passenger traffic model for Copenhagen

    DEFF Research Database (Denmark)

    Overgård, Christian Hansen; VUK, Goran

    2006-01-01

    The paper presents a comprehensive validation procedure for the passenger traffic model for Copenhagen based on external data from the Danish national travel survey and traffic counts. The model was validated for the years 2000 to 2004, with 2004 being of particular interest because the Copenhagen...... matched the observed traffic better than those of the transit assignment model. With respect to the metro forecasts, the model over-predicts metro passenger flows by 10% to 50%. The wide range of findings from the project resulted in two actions. First, a project was started in January 2005 to upgrade...

  3. Visibility of children behind 2010-2013 model year passenger vehicles using glances, mirrors, and backup cameras and parking sensors.

    Science.gov (United States)

    Kidd, David G; Brethwaite, Andrew

    2014-05-01

    This study identified the areas behind vehicles where younger and older children are not visible and measured the extent to which vehicle technologies improve visibility. Rear visibility of targets simulating the heights of a 12-15-month-old, a 30-36-month-old, and a 60-72-month-old child was assessed in 21 2010-2013 model year passenger vehicles with a backup camera or a backup camera plus parking sensor system. The average blind zone for a 12-15-month-old was twice as large as it was for a 60-72-month-old. Large SUVs had the worst rear visibility and small cars had the best. Increases in rear visibility provided by backup cameras were larger than the non-visible areas detected by parking sensors, but parking sensors detected objects in areas near the rear of the vehicle that were not visible in the camera or other fields of view. Overall, backup cameras and backup cameras plus parking sensors reduced the blind zone by around 90 percent on average and have the potential to prevent backover crashes if drivers use the technology appropriately. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Passengers, Crowding and Complexity : Models for passenger oriented public transport

    NARCIS (Netherlands)

    P.C. Bouman (Paul)

    2017-01-01

    markdownabstractPassengers, Crowding and Complexity was written as part of the Complexity in Public Transport (ComPuTr) project funded by the Netherlands Organisation for Scientific Research (NWO). This thesis studies in three parts how microscopic data can be used in models that have the potential

  5. Fleet average NOx emission performance of 2004 model year light-duty vehicles, light-duty trucks and medium-duty passenger vehicles

    International Nuclear Information System (INIS)

    2006-05-01

    The On-Road Vehicle and Engine Emission Regulations came into effect on January 1, 2004. The regulations introduced more stringent national emission standards for on-road vehicles and engines, and also required that companies submit reports containing information concerning the company's fleets. This report presented a summary of the regulatory requirements relating to nitric oxide (NO x ) fleet average emissions for light-duty vehicles, light-duty trucks, and medium-duty passenger vehicles under the new regulations. The effectiveness of the Canadian fleet average NO x emission program at achieving environmental performance objectives was also evaluated. A summary of the fleet average NO x emission performance of individual companies was presented, as well as the overall Canadian fleet average of the 2004 model year based on data submitted by companies in their end of model year reports. A total of 21 companies submitted reports covering 2004 model year vehicles in 10 test groups, comprising 1,350,719 vehicles of the 2004 model year manufactured or imported for the purpose of sale in Canada. The average NO x value for the entire Canadian LDV/LDT fleet was 0.2016463 grams per mile. The average NO x values for the entire Canadian HLDT/MDPV fleet was 0.321976 grams per mile. It was concluded that the NO x values for both fleets were consistent with the environmental performance objectives of the regulations for the 2004 model year. 9 tabs

  6. A Passenger Travel Demand Model for Copenhagen

    DEFF Research Database (Denmark)

    Overgård, Christian Hansen; Jovicic, Goran

    2003-01-01

    The passenger travel model for Copenhagen is a state-of-practice nested logit model in which the sub-models - i.e. generation, distribution and mode choice models - are connected via measure of accessibility. The model includes in its structure a large set of explanatory variables at all three...... aims to provide a detailed description of the model, which can be used as a guide to the future development of similar models. Also, an application of the model in a study of road pricing in denmark is described. This gives the reader an idea of how such a policy measure can be modelled as well...

  7. Modeling and Optimization of Collaborative Passenger Control in Urban Rail Stations under Mass Passenger Flow

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2015-01-01

    Full Text Available With the rapid development of urban rail transit, the phenomenon of outburst passenger flows flocking to stations is occurring much more frequently. Passenger flow control is one of the main methods used to ensure passengers’ safety. While most previous studies have only focused on control measures inside the target station, ignoring the collaboration between stops, this paper puts emphasis on joint passenger control methods during the occurrence of large passenger flows. To provide a theoretic description for the problem under consideration, an integer programming model is built, based on the analysis of passenger delay and the processes by which passengers alight and board. Taking average passenger delay as the objective, the proposed model aims to disperse the pressure of oversaturated stations into others, achieving the optimal state for the entire line. The model is verified using a case study and the results show that restricted access measures taken collaboratively by stations produce less delay and faster evacuation. Finally, a sensitivity analysis is conducted, from which we find that the departure interval and maximum conveying capacity of the train affect passenger delay markedly in the process of passenger control and infer that control measures should be taken at stations near to the one experiencing an emergency.

  8. Econometric Forecasting Models for Air Traffic Passenger of Indonesia

    Directory of Open Access Journals (Sweden)

    Viktor Suryan

    2017-01-01

    Full Text Available One of the major benefits of the air transport services operating in bigger countries is the fact that they provide a vital social economic linkage. This study is an attempt to establish the determinants of the passenger air traffic in Indonesia. The main objective of the study is to determine the economic variables that affect the number of airline passengers using the econometrics model of projection with an emphasis on the use of panel data and to determine the economic variables that affect the number of airline passengers using the econometrics model of projection with an emphasis on the use of time series data. This research also predicts the upcoming number of air traffic passenger until 2030. Air transportation and the economic activity in a country are interdependent. This work first uses the data at the country level and then at the selected airport level for review. The methodology used in this study has adopted the study for both normal regression and panel data regression techniques. Once all these steps are performed, the final equation is taken up for the forecast of the passenger inflow data in the Indonesian airports. To forecast the same, the forecasted numbers of the GDP (Gross Domestic Product and population (independent variables were chosen as a part of the literature review exercise are used. The result of this study shows the GDP per capita have significant related to a number of passengers which the elasticity 2.23 (time-series data and 1.889 for panel data. The exchange rate variable is unrelated to a number of passengers as shown in the value of elasticity. In addition, the total of population gives small value for the elasticity. Moreover, the number of passengers is also affected by the dummy variable (deregulation. With three scenarios: low, medium and high for GDP per capita, the percentage of growth for total number of air traffic passenger from the year 2015 to 2030 is 199.3%, 205.7%, and 320.9% respectively.

  9. The Hybrid Airline Model. Generating Quality for Passengers

    Directory of Open Access Journals (Sweden)

    Bogdan AVRAM

    2017-12-01

    Full Text Available This research aims to investigate the different strategies adopted by the airline companies in adapting to the ongoing changes while developing products and services for passengers in order to increase their yield, load factor and passenger satisfaction. Finding a balance between costs and services quality in the airline industry is a crucial task for every airline wanting to gain a competitive advantage on the market. Also, the rise of the hybrid business operating model has brought up many challenges for airlines as the line between legacy carriers and low-cost carriers is getting thinner in terms of costs and innovative ideas to create a superior product for the passengers.

  10. From laboratory to road: Modeling the divergence between official and real-world fuel consumption and CO_2 emission values in the German passenger car market for the years 2001–2014

    International Nuclear Information System (INIS)

    Tietge, Uwe; Mock, Peter; Franco, Vicente; Zacharof, Nikiforos

    2017-01-01

    Official fuel consumption and carbon dioxide (CO_2) emission values of European passenger cars are widely recognized to be unrepresentative of real-world driving. The divergence between official and real-world values undermines national vehicle taxation schemes and EU-wide CO_2 standards for passenger cars, particularly since the divergence increases with new model generations. This study examines real-world fuel consumption data from more than 130,000 vehicles to investigate the development of the divergence. The analysis validates and refines a regression model developed by , which estimates real-world fuel consumption of cars based on readily available vehicle characteristics, namely official fuel consumption values, vehicle mass, and engine capacity. The regression model yielded coefficients of determination of 0.87 or higher, but was found to underestimate fuel consumption of newer vehicles and company cars. This study proposes to add vehicle build year as a regressor to account for the increasing divergence between official and real-world fuel consumption figures. - Highlights: • Real-world fuel consumption of new cars in Germany is 36% higher than official values. • The divergence between official and real-world fuel consumption has grown over time. • A simple regression accounts for ≥87% of the variance in real-world fuel consumption values. • Vehicle age must be included in the model to account for the growing divergence.

  11. Modeling Hydrogen Refueling Infrastructure to Support Passenger Vehicles †

    Directory of Open Access Journals (Sweden)

    Matteo Muratori

    2018-05-01

    Full Text Available The year 2014 marked hydrogen fuel cell electric vehicles (FCEVs first becoming commercially available in California, where significant investments are being made to promote the adoption of alternative transportation fuels. A refueling infrastructure network that guarantees adequate coverage and expands in line with vehicle sales is required for FCEVs to be successfully adopted by private customers. In this paper, we provide an overview of modelling methodologies used to project hydrogen refueling infrastructure requirements to support FCEV adoption, and we describe, in detail, the National Renewable Energy Laboratory’s scenario evaluation and regionalization analysis (SERA model. As an example, we use SERA to explore two alternative scenarios of FCEV adoption: one in which FCEV deployment is limited to California and several major cities in the United States; and one in which FCEVs reach widespread adoption, becoming a major option as passenger vehicles across the entire country. Such scenarios can provide guidance and insights for efforts required to deploy the infrastructure supporting transition toward different levels of hydrogen use as a transportation fuel for passenger vehicles in the United States.

  12. Train Dwell Time Models for Rail Passenger Service

    Directory of Open Access Journals (Sweden)

    San Hor Peay

    2016-01-01

    Full Text Available In recent years, more studies had been conducted about train dwell time as it is a key parameter of rail system performance and reliability. This paper draws an overview of train dwell time models for rail passenger service from various continents, namely Asia, North America, Europe and Australia. The factors affecting train dwell time are identified and analysed across some rail network operators. The dwell time models developed by various researches are also discussed and reviewed. Finally, the contributions from the outcomes of these models are briefly addressed. In conclusion, this paper suggests that there is a need to further study the factors with strong influence upon dwell time to improve the quality of the train services.

  13. ANALYTICAL AND SIMULATION PLANNING MODEL OF URBAN PASSENGER TRANSPORT

    Directory of Open Access Journals (Sweden)

    Andrey Borisovich Nikolaev

    2017-09-01

    Full Text Available The article described the structure of the analytical and simulation models to make informed decisions in the planning of urban passenger transport. Designed UML diagram that describes the relationship of classes of the proposed model. A description of the main agents of the model developed in the simulation AnyLogic. Designed user interface integration with GIS map. Also provides simulation results that allow concluding about her health and the possibility of its use in solving planning problems of urban passenger transport.

  14. Models for Train Passenger Forecasting of Java and Sumatra

    Science.gov (United States)

    Sartono

    2017-04-01

    People tend to take public transportation to avoid high traffic, especially in Java. In Jakarta, the number of railway passengers is over than the capacity of the train at peak time. This is an opportunity as well as a challenge. If it is managed well then the company can get high profit. Otherwise, it may lead to disaster. This article discusses models for the train passengers, hence, finding the reasonable models to make a prediction overtimes. The Box-Jenkins method is occupied to develop a basic model. Then, this model is compared to models obtained using exponential smoothing method and regression method. The result shows that Holt-Winters model is better to predict for one-month, three-month, and six-month ahead for the passenger in Java. In addition, SARIMA(1,1,0)(2,0,0) is more accurate for nine-month and twelve-month oversee. On the other hand, for Sumatra passenger forecasting, SARIMA(1,1,1)(0,0,2) gives a better approximation for one-month ahead, and ARIMA model is best for three-month ahead prediction. The rest, Trend Seasonal and Liner Model has the least of RMSE to forecast for six-month, nine-month, and twelve-month ahead.

  15. A train dispatching model based on fuzzy passenger demand forecasting during holidays

    Directory of Open Access Journals (Sweden)

    Fei Dou Dou

    2013-03-01

    Full Text Available Abstract: Purpose: The train dispatching is a crucial issue in the train operation adjustment when passenger flow outbursts. During holidays, the train dispatching is to meet passenger demand to the greatest extent, and ensure safety, speediness and punctuality of the train operation. In this paper, a fuzzy passenger demand forecasting model is put up, then a train dispatching optimization model is established based on passenger demand so as to evacuate stranded passengers effectively during holidays. Design/methodology/approach: First, the complex features and regularity of passenger flow during holidays are analyzed, and then a fuzzy passenger demand forecasting model is put forward based on the fuzzy set theory and time series theory. Next, the bi-objective of the train dispatching optimization model is to minimize the total operation cost of the train dispatching and unserved passenger volume during holidays. Finally, the validity of this model is illustrated with a case concerned with the Beijing-Shanghai high-speed railway in China. Findings: The case study shows that the fuzzy passenger demand forecasting model can predict outcomes more precisely than ARIMA model. Thus train dispatching optimization plan proves that a small number of trains are able to serve unserved passengers reasonably and effectively. Originality/value: On the basis of the passenger demand predictive values, the train dispatching optimization model is established, which enables train dispatching to meet passenger demand in condition that passenger flow outbursts, so as to maximize passenger demand by offering the optimal operation plan.

  16. The Danish national passenger modelModel specification and results

    DEFF Research Database (Denmark)

    Rich, Jeppe; Hansen, Christian Overgaard

    2016-01-01

    The paper describes the structure of the new Danish National Passenger model and provides on this basis a general discussion of large-scale model design, cost-damping and model validation. The paper aims at providing three main contributions to the existing literature. Firstly, at the general level......, the paper provides a description of a large-scale forecast model with a discussion of the linkage between population synthesis, demand and assignment. Secondly, the paper gives specific attention to model specification and in particular choice of functional form and cost-damping. Specifically we suggest...... a family of logarithmic spline functions and illustrate how it is applied in the model. Thirdly and finally, we evaluate model sensitivity and performance by evaluating the distance distribution and elasticities. In the paper we present results where the spline-function is compared with more traditional...

  17. Short-Term Bus Passenger Demand Prediction Based on Time Series Model and Interactive Multiple Model Approach

    Directory of Open Access Journals (Sweden)

    Rui Xue

    2015-01-01

    Full Text Available Although bus passenger demand prediction has attracted increased attention during recent years, limited research has been conducted in the context of short-term passenger demand forecasting. This paper proposes an interactive multiple model (IMM filter algorithm-based model to predict short-term passenger demand. After aggregated in 15 min interval, passenger demand data collected from a busy bus route over four months were used to generate time series. Considering that passenger demand exhibits various characteristics in different time scales, three time series were developed, named weekly, daily, and 15 min time series. After the correlation, periodicity, and stationarity analyses, time series models were constructed. Particularly, the heteroscedasticity of time series was explored to achieve better prediction performance. Finally, IMM filter algorithm was applied to combine individual forecasting models with dynamically predicted passenger demand for next interval. Different error indices were adopted for the analyses of individual and hybrid models. The performance comparison indicates that hybrid model forecasts are superior to individual ones in accuracy. Findings of this study are of theoretical and practical significance in bus scheduling.

  18. Modeling of passengers' safety perception for buses on mountainous roads.

    Science.gov (United States)

    Khoo, Hooi Ling; Ahmed, Muaid

    2018-04-01

    This study had developed a passenger safety perception model specifically for buses taking into consideration the various factors, namely driver characteristics, environmental conditions, and bus characteristics using Bayesian Network. The behaviour of bus driver is observed through the bus motion profile, measured in longitudinal, lateral, and vertical accelerations. The road geometry is recorded using GPS and is computed with the aid of the Google map while the perceived bus safety is rated by the passengers in the bus in real time. A total of 13 variables were derived and used in the model development. The developed Bayesian Network model shows that the type of bus and the experience of the driver on the investigated route could have an influence on passenger's perception of their safety on buses. Road geometry is an indirect influencing factor through the driver's behavior. The findings of this model are useful for the authorities to structure an effective strategy to improve the level of perceived bus safety. A high level of bus safety will definitely boost passenger usage confidence which will subsequently increase ridership. Copyright © 2018 Elsevier Ltd. All rights reserved.

  19. A new simulation model for assessing aircraft emergency evacuation considering passenger physical characteristics

    International Nuclear Information System (INIS)

    Liu, Yu; Wang, Weijie; Huang, Hong-Zhong; Li, Yanfeng; Yang, Yuanjian

    2014-01-01

    Conducting a real aircraft evacuation trial is oftentimes unaffordable as it is extremely expensive and may cause severe injury to participants. Simulation models as an alternative have been used to overcome the aforementioned issues in recent years. This paper proposes a new simulation model for emergency evacuation of civil aircraft. Its unique features and advantages over the existing models are twofold: (1) passengers' critical physical characteristics, e.g. waist size, gender, age, and disabilities, which impact the movement and egress time of individual evacuee from a statistical viewpoint, are taken into account in the new model. (2) Improvements are made to enhance the accuracy of the simulation model from three aspects. First, the staggered mesh discretization method together with the agent-based approach is utilized to simulate movements of individual passengers in an emergency evacuation process. Second, each node discretized to represent cabin space in the new model can contain more than one passenger if they are moving in the same direction. Finally, each individual passenger is able to change his/her evacuation route in a real-time manner based upon the distance from the current position to the target exit and the queue length. The effectiveness of the proposed simulation model is demonstrated on Boeing 767-300 aircraft. - Highlights: • A new simulation model of aircraft emergency evacuation is developed. • Some critical physical characteristics of passengers', e.g. waist size, gender, age, and disabilities, are taken into account in the new model. • An agent-based approach along with a multi-level fine network representation is used. • Passengers are able to change their evacuation routes in a real-time manner based upon distance and length of queue

  20. Alighting and Boarding Time Model of Passengers at a LRT Station in Kuala Lumpur

    Directory of Open Access Journals (Sweden)

    Hor Peay San

    2017-01-01

    Full Text Available A research was conducted to study the factors affecting the alighting and boarding rate of passengers and establish a prediction model for alighting and boarding time of passengers for a passenger rail service in Malaysia. Data was collected at the KL Sentral LRT station during the morning and evening peak hours for a period of 5 working days. Results show that passenger behaviour, passenger volume, crowdedness in train and mixture of flow has significant effects on the alighting and boarding time though mixture of flow is not significant in the prediction model produced due to the passenger behaviour at the platform.

  1. PASSENGER TRAFFIC MOVEMENT MODELLING BY THE CELLULAR-AUTOMAT APPROACH

    Directory of Open Access Journals (Sweden)

    T. Mikhaylovskaya

    2009-01-01

    Full Text Available The mathematical model of passenger traffic movement developed on the basis of the cellular-automat approach is considered. The program realization of the cellular-automat model of pedastrians streams movement in pedestrian subways at presence of obstacles, at subway structure narrowing is presented. The optimum distances between the obstacles and the angle of subway structure narrowing providing pedastrians stream safe movement and traffic congestion occurance are determined.

  2. Energy scenarios for European passenger transport in the year 2030

    Energy Technology Data Exchange (ETDEWEB)

    Rienstra, S.A.; Nijkamp, P. [Systems and Control Group, Faculty of Mechanical and Marine Engineering, Delft University of Technology, Delft (Netherlands)] Smokers, R.T.M. [ECN Policy Studies, Petten (Netherlands)

    1995-11-01

    In this paper four energy scenarios for West-European passenger transport are developed. To start with, the present transport system as a baseline case is described and analysed. Next, for each scenario it is outlined how the passenger transport system may look like in terms of the use of various existing and future transport technologies and the corresponding modal split. Based on this information, expected energy consumption features of the various transport modes are described, data on the present fuel supply and electricity generation system are provided, and estimations of the future energy system are given. Then, the energy consumption and CO2 emissions associated with the future passenger transport systems are calculated and these impacts are compared with the current system. The conclusion is that a large-scale reduction of CO2 emissions is possible in several ways, but that each option will cause many problems because drastic policy measures will have to be introduced, which may affect economic growth and the lifestyles of individuals. 4 figs., 11 tabs., 22 refs.

  3. A Model of Bus Bunching under Reliability-based Passenger Arrival Patterns

    OpenAIRE

    Fonzone, Achille; Schmöcker, Jan-Dirk; Liu, Ronghui

    2015-01-01

    If bus service departure times are not completely unknown to the passengers, non-uniform passenger arrival patterns can be expected. We propose that passengers decide their arrival time at stops based on a continuous logit model that considers the risk of missing services. Expected passenger waiting times are derived in a bus system that allows also for overtaking between bus services. We then propose an algorithm to derive the dwell time of subsequent buses serving a stop in order to illustr...

  4. Assessment of NHTSA’s Report “Relationships Between Fatality Risk, Mass, and Footprint in Model Year 2003-2010 Passenger Cars and LTVs”

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2016-06-01

    NHTSA recently completed a logistic regression analysis updating its 2003, 2010, and 2012 studies of the relationship between vehicle mass and US fatality risk per vehicle mile traveled (VMT; Kahane 2010, Kahane 2012, Puckett 2016). The new study updates the 2012 analysis using FARS data from 2005 to 2011 for model year 2003 to 2010. Using the updated databases, NHTSA estimates that reducing vehicle mass by 100 pounds while holding footprint fixed would increase fatality risk per VMT by 1.49% for lighter-than-average cars and by 0.50% for heavierthan- average cars, but reduce risk by 0.10% for lighter-than-average light-duty trucks, by 0.71% for heavier-than-average light-duty trucks, and by 0.99% for CUVs/minivans. Using a jack knife method to estimate the statistical uncertainty of these point estimates, NHTSA finds that none of these estimates are statistically significant at the 95% confidence level; however, the 1.49% increase in risk associated with mass reduction in lighter-than-average cars, and the 0.71% and 0.99% decreases in risk associated with mass reduction in heavier-than-average light trucks and CUVs/minivans, are statistically significant at the 90% confidence interval. The effect of mass reduction on risk that NHTSA estimated in 2016 is more beneficial than in its 2012 study, particularly for light trucks and CUVs/minivans. The 2016 NHTSA analysis estimates that reducing vehicle footprint by one square foot while holding mass constant would increase fatality risk per VMT by 0.28% in cars, by 0.38% in light trucks, and by 1.18% in CUVs and minivans.This report replicates the 2016 NHTSA analysis, and reproduces their main results. This report uses the confidence intervals output by the logistic regression models, which are smaller than the intervals NHTSA estimated using a jack-knife technique that accounts for the sampling error in the FARS fatality and state crash data. In addition to reproducing the NHTSA results, this report also examines the

  5. Assessment of NHTSA’s Report “Relationships Between Fatality Risk, Mass, and Footprint in Model Year 2004-2011 Passenger Cars and LTVs” (LBNL Phase 1)

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom P.

    2018-03-28

    reduction while maintaining footprint on societal U.S. fatality risk is small, and not statistically significant at the 95% or 90% confidence level for all vehicle types based on the jack-knife method NHTSA used. This report also finds that the estimated effects of other control variables, such as vehicle type, specific safety technologies, and crash conditions such as whether the crash occurred at night, in a rural county, or on a high-speed road, on risk are much larger, in some cases two orders of magnitude larger, than the estimated effect of mass or footprint reduction on risk. Finally, this report shows that after accounting for the many vehicle, driver, and crash variables NHTSA used in its regression analyses, there remains a wide variation in risk by vehicle make and model, and this variation is unrelated to vehicle mass. Although the purpose of the NHTSA and LBNL reports is to estimate the effect of vehicle mass reduction on societal risk, this is not exactly what the regression models are estimating. Rather, they are estimating the recent historical relationship between mass and risk, after accounting for most measurable differences between vehicles, drivers, and crash times and locations. In essence, the regression models are comparing the risk of a 2600-lb Dodge Neon with that of a 2500-lb Honda Civic, after attempting to account for all other differences between the two vehicles. The models are not estimating the effect of literally removing 100 pounds from the Neon, leaving everything else unchanged. In addition, the analyses are based on the relationship of vehicle mass and footprint on risk for recent vehicle designs (model year 2004 to 2011). These relationships may or may not continue into the future as manufacturers utilize new vehicle designs and incorporate new technologies, such as more extensive use of strong lightweight materials and specific safety technologies. Therefore, throughout this report we use the phrase “the estimated effect of mass (or

  6. Models in Planning Urban Public Passenger Transport

    Directory of Open Access Journals (Sweden)

    Gordana Štefančić

    2007-07-01

    Full Text Available The solving of complex problems in public transport requiresthe usage of models that are based on the estimate of demandin planning the transport routes. The intention is to predictwhat is going to happen in the future, if the proposed solutionsare implemented. In the majority of cases, the publictransport system is formed as a network and stored in the computermemory in order to start the evaluation process by specifYingthe number of trip origins and destinations in each zone.The trip distribution model which is used to calculate the numberof trips between each pair in the zone is based on the overalltravel frictions from zone to zone.

  7. MATHEMATICAL MODELING OF UNSTEADY HEAT EXCHANGE IN A PASSENGER CAR

    Directory of Open Access Journals (Sweden)

    I. Yu. Khomenko

    2013-07-01

    Full Text Available Purpose.Existing mathematicalmodelsofunsteadyheatexchangeinapassengercardonotsatisfytheneedofthedifferentconstructivedecisionsofthelifesupportsystemefficiencyestimation. They also don’t allow comparing new and old life support system constructions influence on the inner environment conditions. Moreoverquite frequently unsteady heat exchange processes were studied at the initial car motion stage. Due to the new competitive engineering decisionsof the lifesupportsystemthe need of a new mathematical instrument that would satisfy the mentioned features and their influence on the unsteadyheatexchangeprocesses during the whole time of the road appeared. The purpose of this work is creation of the mathematicalmodel ofunsteadyheatexchangeinapassengercarthatcan satisfythe above-listed requirements. Methodology. Fortheassigned task realizationsystemofdifferentialequationsthatcharacterizesunsteadyheatexchangeprocessesinapassengercarwascomposed; forthesystemof equationssolution elementary balance method was used. Findings. Computational algorithm was developed andcomputer program for modeling transitional heat processes in the car was designed. It allows comparing different life support system constructions influence on the inner environment conditionsand unsteady heat exchange processes can be studied at every car motion stage. Originality.Mathematicalmodelofunsteadyheatexchangeinapassengercarwasimproved. That is why it can be used for the heat engineering studying of the inner car state under various conditions and for the operation of the different life support systems of passenger cars comparison. Mathematicalmodelingofunsteadyheatexchangeinapassengercarwas made by the elementary balance method. Practical value. Created mathematical model gives the possibility to simulate temperature changes in passenger car on unsteady thermal conditions with enough accuracy and to introduce and remove additional elements to the designed model. Thus different

  8. A trade-off analysis design tool. Aircraft interior noise-motion/passenger satisfaction model

    Science.gov (United States)

    Jacobson, I. D.

    1977-01-01

    A design tool was developed to enhance aircraft passenger satisfaction. The effect of aircraft interior motion and noise on passenger comfort and satisfaction was modelled. Effects of individual aircraft noise sources were accounted for, and the impact of noise on passenger activities and noise levels to safeguard passenger hearing were investigated. The motion noise effect models provide a means for tradeoff analyses between noise and motion variables, and also provide a framework for optimizing noise reduction among noise sources. Data for the models were collected onboard commercial aircraft flights and specially scheduled tests.

  9. Auralization of Accelerating Passenger Cars Using Spectral Modeling Synthesis

    Directory of Open Access Journals (Sweden)

    Reto Pieren

    2015-12-01

    Full Text Available While the technique of auralization has been in use for quite some time in architectural acoustics, the application to environmental noise has been discovered only recently. With road traffic noise being the dominant noise source in most countries, particular interest lies in the synthesis of realistic pass-by sounds. This article describes an auralizator for pass-bys of accelerating passenger cars. The key element is a synthesizer that simulates the acoustical emission of different vehicles, driving on different surfaces, under different operating conditions. Audio signals for the emitted tire noise, as well as the propulsion noise are generated using spectral modeling synthesis, which gives complete control of the signal characteristics. The sound of propulsion is synthesized as a function of instantaneous engine speed, engine load and emission angle, whereas the sound of tires is created in dependence of vehicle speed and emission angle. The sound propagation is simulated by applying a series of time-variant digital filters. To obtain the corresponding steering parameters of the synthesizer, controlled experiments were carried out. The tire noise parameters were determined from coast-by measurements of passenger cars with idling engines. To obtain the propulsion noise parameters, measurements at different engine speeds, engine loads and emission angles were performed using a chassis dynamometer. The article shows how, from the measured data, the synthesizer parameters are calculated using audio signal processing.

  10. Integrating passenger and freight transportation : model formulation and insights

    NARCIS (Netherlands)

    Ghilas, V.; Demir, E.; Woensel, van T.

    2013-01-01

    Integrating passenger and freight ows creates attractive business opportunities because the same transportation needs can be met with fewer vehicles and emissions. This paper seeks an integrated solution for the transportation of passenger and freight simultaneously, so that fewer vehicles are

  11. Getting Frustrated: Modelling Emotion Contagion in Stranded Passengers

    NARCIS (Netherlands)

    van der Wal, C. Natalie; Couwenberg, Maik; Bosse, T.

    2017-01-01

    Train passengers can get stranded due to a variety of events, such as a delay, technical malfunctioning or a natural disaster. Stranded passengers can get frustrated, which could escalate in misbehaviours. Examples are verbal and physical violence or dangerous behaviours such as opening emergency

  12. Passenger Flow Forecasting Research for Airport Terminal Based on SARIMA Time Series Model

    Science.gov (United States)

    Li, Ziyu; Bi, Jun; Li, Zhiyin

    2017-12-01

    Based on the data of practical operating of Kunming Changshui International Airport during2016, this paper proposes Seasonal Autoregressive Integrated Moving Average (SARIMA) model to predict the passenger flow. This article not only considers the non-stationary and autocorrelation of the sequence, but also considers the daily periodicity of the sequence. The prediction results can accurately describe the change trend of airport passenger flow and provide scientific decision support for the optimal allocation of airport resources and optimization of departure process. The result shows that this model is applicable to the short-term prediction of airport terminal departure passenger traffic and the average error ranges from 1% to 3%. The difference between the predicted and the true values of passenger traffic flow is quite small, which indicates that the model has fairly good passenger traffic flow prediction ability.

  13. Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network.

    Directory of Open Access Journals (Sweden)

    Haodong Yin

    Full Text Available A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1 A basic passenger behavior optimization model is mathematically constructed based on 0-1 integer programming to describe passengers' responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2 An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1, the impact of the closure can be somewhat mitigated.

  14. Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network.

    Science.gov (United States)

    Yin, Haodong; Han, Baoming; Li, Dewei; Wu, Jianjun; Sun, Huijun

    2016-01-01

    A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1) A basic passenger behavior optimization model is mathematically constructed based on 0-1 integer programming to describe passengers' responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2) An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1), the impact of the closure can be somewhat mitigated.

  15. A statistical mechanics model for free-for-all airplane passenger boarding

    Energy Technology Data Exchange (ETDEWEB)

    Steffen, Jason H.; /Fermilab

    2008-08-01

    I discuss a model for free-for-all passenger boarding which is employed by some discount air carriers. The model is based on the principles of statistical mechanics where each seat in the aircraft has an associated energy which reflects the preferences of travelers. As each passenger enters the airplane they select their seats using Boltzmann statistics, proceed to that location, load their luggage, sit down, and the partition function seen by remaining passengers is modified to reflect this fact. I discuss the various model parameters and make qualitative comparisons of this passenger boarding model with those that involve assigned seats. The model can be used to predict the probability that certain seats will be occupied at different times during the boarding process. These results might provide a useful description of this boarding method. The model is a relatively unusual application of undergraduate level physics and describes a situation familiar to many students and faculty.

  16. A statistical mechanics model for free-for-all airplane passenger boarding

    Science.gov (United States)

    Steffen, Jason H.

    2008-12-01

    I discuss a model for free-for-all passenger boarding which is employed by some discount air carriers. The model is based on the principles of statistical mechanics, where each seat in the aircraft has an associated energy which reflects the preferences of travelers. As each passenger enters the airplane they select their seats using Boltzmann statistics, proceed to that location, load their luggage, sit down, and the partition function seen by remaining passengers is modified to reflect this fact. I discuss the various model parameters and make qualitative comparisons of this passenger boarding model with those that involve assigned seats. The model can be used to predict the probability that certain seats will be occupied at different times during the boarding process. These results might provide a useful description of this boarding method. The model is a relatively unusual application of undergraduate level physics and describes a situation familiar to many students and faculty.

  17. A statistical mechanics model for free-for-all airplane passenger boarding

    International Nuclear Information System (INIS)

    Steffen, Jason H.; Fermilab

    2008-01-01

    I discuss a model for free-for-all passenger boarding which is employed by some discount air carriers. The model is based on the principles of statistical mechanics where each seat in the aircraft has an associated energy which reflects the preferences of travelers. As each passenger enters the airplane they select their seats using Boltzmann statistics, proceed to that location, load their luggage, sit down, and the partition function seen by remaining passengers is modified to reflect this fact. I discuss the various model parameters and make qualitative comparisons of this passenger boarding model with those that involve assigned seats. The model can be used to predict the probability that certain seats will be occupied at different times during the boarding process. These results might provide a useful description of this boarding method. The model is a relatively unusual application of undergraduate level physics and describes a situation familiar to many students and faculty

  18. Modeling and Simulating Passenger Behavior for a Station Closure in a Rail Transit Network

    Science.gov (United States)

    Yin, Haodong; Han, Baoming; Li, Dewei; Wu, Jianjun; Sun, Huijun

    2016-01-01

    A station closure is an abnormal operational situation in which the entrances or exits of a rail transit station have to be closed for some time due to an unexpected incident. A novel approach is developed to estimate the impacts of the alternative station closure scenarios on both passenger behavioral choices at the individual level and passenger demand at the disaggregate level in a rail transit network. Therefore, the contributions of this study are two-fold: (1) A basic passenger behavior optimization model is mathematically constructed based on 0–1 integer programming to describe passengers’ responses to alternative origin station closure scenarios and destination station closure scenarios; this model also considers the availability of multi-mode transportation and the uncertain duration of the station closure; (2) An integrated solution algorithm based on the passenger simulation is developed to solve the proposed model and to estimate the effects of a station closure on passenger demand in a rail transit network. Furthermore, 13 groups of numerical experiments based on the Beijing rail transit network are performed as case studies with 2,074,267 records of smart card data. The comparisons of the model outputs and the manual survey show that the accuracy of our proposed behavior optimization model is approximately 80%. The results also show that our model can be used to capture the passenger behavior and to quantitatively estimate the effects of alternative closure scenarios on passenger flow demand for the rail transit network. Moreover, the closure duration and its overestimation greatly influence the individual behavioral choices of the affected passengers and the passenger demand. Furthermore, if the rail transit operator can more accurately estimate the closure duration (namely, as g approaches 1), the impact of the closure can be somewhat mitigated. PMID:27935963

  19. Self-propelled pedestrian dynamics model: Application to passenger movement and infection propagation in airplanes

    OpenAIRE

    Namilae, S.; Srinivasan, A.; Mubayi, A.; Scotch, M.; Pahle, R.

    2017-01-01

    Reducing the number of contacts between passengers on an airplane can potentially curb the spread of infectious diseases. In this paper, a social force based pedestrian movement model is formulated and applied to evaluate the movement and contacts among passengers during boarding and deplaning of an airplane. Within the social force modeling framework, we introduce location dependence on the self-propelling momentum of pedestrian particles. The model parameters are varied over a large design ...

  20. An Evacuation Model for Passenger Ships That Includes the Influence of Obstacles in Cabins

    Directory of Open Access Journals (Sweden)

    Baocheng Ni

    2017-01-01

    Full Text Available Passenger behavior and ship environment are the key factors affecting evacuation efficiency. However, current studies ignore the interior layout of passenger ship cabins and treat the cabins as empty rooms. To investigate the influence of obstacles (e.g., tables and stools on cabin evacuation, we propose an agent-based social force model for advanced evacuation analysis of passenger ships; this model uses a goal-driven submodel to determine a plan and an extended social force submodel to govern the movement of passengers. The extended social force submodel considers the interaction forces between the passengers, crew, and obstacles and minimises the range of these forces to improve computational efficiency. We drew the following conclusions based on a series of evacuation simulations conducted in this study: (1 the proposed model endows the passenger with the behaviors of bypassing and crossing obstacles, (2 funnel-shaped exits from cabins can improve evacuation efficiency, and (3 as the exit angle increases, the evacuation time also increases. These findings offer ship designers some insight towards increasing the safety of large passenger ships.

  1. An open-access modeled passenger flow matrix for the global air network in 2010.

    Science.gov (United States)

    Huang, Zhuojie; Wu, Xiao; Garcia, Andres J; Fik, Timothy J; Tatem, Andrew J

    2013-01-01

    The expanding global air network provides rapid and wide-reaching connections accelerating both domestic and international travel. To understand human movement patterns on the network and their socioeconomic, environmental and epidemiological implications, information on passenger flow is required. However, comprehensive data on global passenger flow remain difficult and expensive to obtain, prompting researchers to rely on scheduled flight seat capacity data or simple models of flow. This study describes the construction of an open-access modeled passenger flow matrix for all airports with a host city-population of more than 100,000 and within two transfers of air travel from various publicly available air travel datasets. Data on network characteristics, city population, and local area GDP amongst others are utilized as covariates in a spatial interaction framework to predict the air transportation flows between airports. Training datasets based on information from various transportation organizations in the United States, Canada and the European Union were assembled. A log-linear model controlling the random effects on origin, destination and the airport hierarchy was then built to predict passenger flows on the network, and compared to the results produced using previously published models. Validation analyses showed that the model presented here produced improved predictive power and accuracy compared to previously published models, yielding the highest successful prediction rate at the global scale. Based on this model, passenger flows between 1,491 airports on 644,406 unique routes were estimated in the prediction dataset. The airport node characteristics and estimated passenger flows are freely available as part of the Vector-Borne Disease Airline Importation Risk (VBD-Air) project at: www.vbd-air.com/data.

  2. An Integrated Rolling Stock Planning Model for the Copenhagen Suburban Passenger Railway

    DEFF Research Database (Denmark)

    Thorlacius, Per; Larsen, Jesper; Laumanns, Marco

    A central issue for operators of passenger railways is providing sufficient number of seats for passengers while at the same time minimising operating costs. This is the task of rolling stock planning. Due to the large number of practical, railway specific requirements that a rolling stock plan has...... to take into account, rolling stock plans are often constructed in a step-by-step manner, taking some requirements into consideration in each step. This may make it difficult in the final step to produce a plan that is feasible with regard to all of the requirements and at the same time economically...... attractive. This paper proposes an integrated rolling stock planning model that simultaneously takes into account all practical requirements for rolling stock planning at DSB S-tog, the suburban passenger train operator of the City of Copenhagen. The model is then used to improve existing rolling stock plans...

  3. An integrated rolling stock planning model for the Copenhagen suburban passenger railway

    DEFF Research Database (Denmark)

    Thorlacius, Per; Larsen, Jesper; Laumanns, Marco

    2015-01-01

    A central issue for operators of passenger railways is providing sufficient number of seats for passengers while at the same time minimising operating costs. This is the task of rolling stock planning. Due to the large number of practical, railway specific requirements that a rolling stock plan has...... to take into account, rolling stock plans are often constructed in a step-by-step manner, taking some requirements into consideration in each step. This may make it difficult in the final step to produce a plan that is feasible with regard to all of the requirements and at the same time economically...... attractive. This paper proposes an integrated rolling stock planning model that simultaneously takes into account all practical requirements for rolling stock planning at DSB S-tog, the suburban passenger train operator of the City of Copenhagen. The model is then used to improve existing rolling stock plans...

  4. MACRO MODEL OF SEAT BELT USE BY CAR DRIVERS AND PASSENGERS

    Directory of Open Access Journals (Sweden)

    Kazimierz JAMROZ

    2013-12-01

    Full Text Available The article presents some problems of seat belt use by car drivers and passengers. It looks in particular at seat belt use and effectiveness in selected countries. Next, factors of seat belt use are presented and methodology of model development. A macro model of seat belt use is presented based on data from around fifty countries from different continents.

  5. 49 CFR 537.7 - Pre-model year and mid-model year reports.

    Science.gov (United States)

    2010-10-01

    ... accordance with subpart D of 40 CFR part 600, (2) Body style, (3) Beginning model year 2010, base tire as...) Passenger-carrying volume, (2) Cargo-carrying volume, (3) Beginning model year 2008, base tire as defined in...; (ii) Departure angle; (iii) Breakover angle; (iv) Axle clearance; (v) Minimum running clearance; and...

  6. Modeling the effect of operator and passenger characteristics on the fatality risk of motorcycle crashes.

    Science.gov (United States)

    Tavakoli Kashani, Ali; Rabieyan, Rahim; Besharati, Mohammad Mehdi

    2016-01-01

    In Iran more than 25% of crash fatalities belong to motorcycle operators and passengers in the recent years, from which about 20% are related to passenger fatalities. The aim of this study was to investigate the motorcycle operator and passenger characteristics as well as other contributory factors that may affect the fatality risk of motorcyclists involved in traffic crashes. To this end, motorcycle crash data between 2009 and 2012 was extracted from Iran traffic crash database and a logistic regression analysis was performed to obtain odds ratio estimates for each of the study variables. The fatality risk of motorcyclists has a direct relationship with the number of pillion passengers carried. Results also indicate that the amount of increase in the likelihood of having a fatality in a motorcycles crash is considerably higher when the operator is accompanied by a male passenger of the same age. Furthermore, results showed that if the crash is occurred in the darkness, on curves, in rural areas and on highways, then the crash would be more likely to be fatal. Moreover, the head-on collisions, older operators, unlicensed operators and not using a safety helmet were found to increase the likelihood of a fatality in a motorcycle crash. Preventative measures such as, imposing stricter rules regarding safety helmet usage and confining the number of pillion passengers to one, might be implemented to reduce the fatality risk in motorcycle crashes. In addition, more appropriate infrastructures for penalizing offending motorcyclists could also reduce the frequency of law violations such as not wearing helmet or riding without motorcycle license, which in turn, would result into a reduction in the fatality risk of motorcycle crashes. © 2016 KUMS, All rights reserved.

  7. MATHEMATICAL MODEL OF UNSTEADY HEAT TRANSFER OF PASSENGER CAR WITH HEATING SYSTEM

    Directory of Open Access Journals (Sweden)

    E. V. Biloshytskyi

    2018-02-01

    Full Text Available Purpose. The existing mathematical models of unsteady heat processes in a passenger car do not fully reflect the thermal processes, occurring in the car wits a heating system. In addition, unsteady heat processes are often studied in steady regime, when the heat fluxes and the parameters of the thermal circuit are constant and do not depend on time. In connection with the emergence of more effective technical solutions to the life support system there is a need for creating a new mathematical apparatus, which would allow taking into account these features and their influence on the course of unsteady heat processes throughout the travel time. The purpose of this work is to create a mathematical model of the heat regime of a passenger car with a heating system that takes into account the unsteady heat processes. Methodology. To achieve this task the author composed a system of differential equations, describing unsteady heat processes during the heating of a passenger car. For the solution of the composed system of equations, the author used the method of elementary balances. Findings. The paper presents the developed numerical algorithm and computer program for simulation of transitional heat processes in a locomotive traction passenger car, which allows taking into account the various constructive solutions of the life support system of passenger cars and to simulate unsteady heat processes at any stage of the trip. Originality. For the first time the author developed a mathematical model of heat processes in a car with a heating system, that unlike existing models, allows to investigate the unsteady heat engineering performance in the cabin of the car under different operating conditions and compare the work of various life support systems from the point of view their constructive solutions. Practical value. The work presented the developed mathematical model of the unsteady heat regime of the passenger car with a heating system to estimate

  8. Literature review of the passenger airline business models : Full service carrier, low-cost carrier and charter airlines

    NARCIS (Netherlands)

    Carmona Benitez, R.B.; Lodewijks, G.

    2008-01-01

    The deregulation and liberalization of the air transportation industry have developed three main passenger business models: full service carriers, low-cost carriers, and charter airlines. Deregulation removed regulated fares and routes increasing competition and yields. Airlines business models main

  9. Individual Travel Behavior Modeling of Public Transport Passenger Based on Graph Construction

    OpenAIRE

    Quan Liang; Jiancheng Weng; Wei Zhou; Selene Baez Santamaria; Jianming Ma; Jian Rong

    2018-01-01

    This paper presents a novel method for mining the individual travel behavior regularity of different public transport passengers through constructing travel behavior graph based model. The individual travel behavior graph is developed to represent spatial positions, time distributions, and travel routes and further forecasts the public transport passenger’s behavior choice. The proposed travel behavior graph is composed of macronodes, arcs, and transfer probability. Each macronode corresponds...

  10. MATHEMATICAL MODEL OF UNSTEADY HEAT TRANSFER OF PASSENGER CAR WITH HEATING SYSTEM

    OpenAIRE

    E. V. Biloshytskyi

    2018-01-01

    Purpose. The existing mathematical models of unsteady heat processes in a passenger car do not fully reflect the thermal processes, occurring in the car wits a heating system. In addition, unsteady heat processes are often studied in steady regime, when the heat fluxes and the parameters of the thermal circuit are constant and do not depend on time. In connection with the emergence of more effective technical solutions to the life support system there is a need for creating a new mathematical...

  11. Individual Travel Behavior Modeling of Public Transport Passenger Based on Graph Construction

    Directory of Open Access Journals (Sweden)

    Quan Liang

    2018-01-01

    Full Text Available This paper presents a novel method for mining the individual travel behavior regularity of different public transport passengers through constructing travel behavior graph based model. The individual travel behavior graph is developed to represent spatial positions, time distributions, and travel routes and further forecasts the public transport passenger’s behavior choice. The proposed travel behavior graph is composed of macronodes, arcs, and transfer probability. Each macronode corresponds to a travel association map and represents a travel behavior. A travel association map also contains its own nodes. The nodes of a travel association map are created when the processed travel chain data shows significant change. Thus, each node of three layers represents a significant change of spatial travel positions, travel time, and routes, respectively. Since a travel association map represents a travel behavior, the graph can be considered a sequence of travel behaviors. Through integrating travel association map and calculating the probabilities of the arcs, it is possible to construct a unique travel behavior graph for each passenger. The data used in this study are multimode data matched by certain rules based on the data of public transport smart card transactions and network features. The case study results show that graph based method to model the individual travel behavior of public transport passengers is effective and feasible. Travel behavior graphs support customized public transport travel characteristics analysis and demand prediction.

  12. Dynamic Passenger Assignment during Disruptions in Railway Systems

    NARCIS (Netherlands)

    Zhu, Y.; Goverde, R.M.P.

    2017-01-01

    Passenger-oriented rescheduling problems receive increasing attention. However, the passenger assignment models used for evaluating the rescheduling solutions are usually simplified by many assumptions. To estimate passenger inconvenience more accurately, this paper establishes a dynamic passenger

  13. Impacts of privatising Britain's rail passenger services -- franchising, refranchising, and Ten Year Transport Plan targets

    OpenAIRE

    Richard D Knowles

    2004-01-01

    Britain's passenger rail services were privatised in 1996/97 to reduce public subsidies and produce customer benefits through the private sector competing for medium or long-term franchises. Private sector franchisees were committed to investment in rolling stock, services, and infrastructure and were expected to deliver more market-oriented and cost-effective services whilst subsidies decreased on an annual sliding scale. The author analyses why some franchisees have been unable to achieve t...

  14. Relieving the Impact of Transit Signal Priority on Passenger Cars through a Bilevel Model

    Directory of Open Access Journals (Sweden)

    Ding Wang

    2017-01-01

    Full Text Available Transit signal priority (TSP is an effective control strategy to improve transit operations on the urban network. However, the TSP may sacrifice the right-of-way of vehicles from side streets which have only few transit vehicles; therefore, how to minimize the negative impact of TSP strategy on the side streets is an important issue to be addressed. Concerning the typical mixed-traffic flow pattern and heavy transit volume in China, a bilevel model is proposed in this paper: the upper-level model focused on minimizing the vehicle delay in the nonpriority direction while ensuring acceptable delay variation in transit priority direction, and the lower-level model aimed at minimizing the average passenger delay in the entire intersection. The parameters which will affect the efficiency of the bilevel model have been analyzed based on a hypothetical intersection. Finally, a real-world intersection has been studied, and the average vehicle delay in the nonpriority direction decreased 11.28 s and 22.54 s (under different delay variation constraint compared to the models that only minimize average passenger delay, while the vehicle delay in the priority direction increased only 1.37 s and 2.87 s; the results proved the practical applicability and efficiency of the proposed bilevel model.

  15. Frontal and oblique crash tests of HIII 6-year-old child ATD using real-world, observed child passenger postures.

    Science.gov (United States)

    Bohman, Katarina; Arbogast, Kristy B; Loeb, Helen; Charlton, Judith L; Koppel, Sjaan; Cross, Suzanne L

    2018-02-28

    The aim of this study was to evaluate the consequences of frontal and oblique crashes when positioning a Hybrid III (HIII) 6-year-old child anthropometric test device (ATD) using observed child passenger postures from a naturalistic driving study (NDS). Five positions for booster-seated children aged 4-7 years were selected, including one reference position according to the FMVSS 213 ATD seating protocol and 4 based on real-world observed child passenger postures from an NDS including 2 user positions with forward tilting torso and 2 that combined both forward and lateral inboard tilting of the torso. Seventeen sled tests were conducted in a mid-sized vehicle body at 64 km/h (European New Car Assessment Programme [Euro NCAP] Offset Deformable Barrier [ODB] pulse), in full frontal and oblique (15°) crash directions. The rear-seated HIII 6-year-old child ATD was restrained on a high-back booster seat. In 10 tests, the booster seat was also attached with a top tether. In the oblique tests, the ATD was positioned on the far side. Three camera views and ATD responses (head, neck, and chest) were analyzed. The shoulder belt slipped off the shoulder in all ATD positions in the oblique test configuration. In full frontal tests, the shoulder belt stayed on the shoulder in 3 out of 9 tests. Head acceleration and neck tension were decreased in the forward leaning positions; however, the total head excursion increased up to 210 mm compared to te reference position, due to belt slip-off and initial forward leaning position. These results suggest that real-world child passenger postures may contribute to shoulder belt slip-off and increased head excursion, thus increasing the risk of head injury. Restraint system development needs to include a wider range of sitting postures that children may choose, in addition to the specified postures of ATDs in seating test protocols, to ensure robust performance across diverse use cases. In addition, these tests revealed that the child

  16. Developing a Risk Model for Fire in Passenger Ships - Based on Bayesian Belief Network

    OpenAIRE

    Dokmo, Hanne Bjørkås

    2016-01-01

    Passenger ships, especially cruise ships, are rapidly increasing in size. With larger vessels, comes a greater risk to the passengers if something where to happen. A fire on a passenger vessel can spread quickly, and with as much as thousands of people needing to be evacuated many things could go wrong. The issue of the safety on board is therefore crucial to consider, seeing as the consequences could be tremendous. There are three types of passenger ships; Passenger vessel, RoPax vessel and ...

  17. Simulation-Based Dynamic Passenger Flow Assignment Modelling for a Schedule-Based Transit Network

    Directory of Open Access Journals (Sweden)

    Xiangming Yao

    2017-01-01

    Full Text Available The online operation management and the offline policy evaluation in complex transit networks require an effective dynamic traffic assignment (DTA method that can capture the temporal-spatial nature of traffic flows. The objective of this work is to propose a simulation-based dynamic passenger assignment framework and models for such applications in the context of schedule-based rail transit systems. In the simulation framework, travellers are regarded as individual agents who are able to obtain complete information on the current traffic conditions. A combined route selection model integrated with pretrip route selection and entrip route switch is established for achieving the dynamic network flow equilibrium status. The train agent is operated strictly with the timetable and its capacity limitation is considered. A continuous time-driven simulator based on the proposed framework and models is developed, whose performance is illustrated through a large-scale network of Beijing subway. The results indicate that more than 0.8 million individual passengers and thousands of trains can be simulated simultaneously at a speed ten times faster than real time. This study provides an efficient approach to analyze the dynamic demand-supply relationship for large schedule-based transit networks.

  18. Construction of Monitoring Model and Algorithm Design on Passenger Security during Shipping Based on Improved Bayesian Network

    Science.gov (United States)

    Wang, Jiali; Zhang, Qingnian; Ji, Wenfeng

    2014-01-01

    A large number of data is needed by the computation of the objective Bayesian network, but the data is hard to get in actual computation. The calculation method of Bayesian network was improved in this paper, and the fuzzy-precise Bayesian network was obtained. Then, the fuzzy-precise Bayesian network was used to reason Bayesian network model when the data is limited. The security of passengers during shipping is affected by various factors, and it is hard to predict and control. The index system that has the impact on the passenger safety during shipping was established on basis of the multifield coupling theory in this paper. Meanwhile, the fuzzy-precise Bayesian network was applied to monitor the security of passengers in the shipping process. The model was applied to monitor the passenger safety during shipping of a shipping company in Hainan, and the effectiveness of this model was examined. This research work provides guidance for guaranteeing security of passengers during shipping. PMID:25254227

  19. Behavioural Models for Route Choice of Passengers in Multimodal Public Transport Networks

    DEFF Research Database (Denmark)

    Anderson, Marie Karen

    in the estimation of route choice models of public transport users based upon observed choices. Public transport route choice models have not benefitted from the same technological enhancements as car models because of the necessity (i) to collect additional information concerning lines and transfers, and (ii...... modes, public transport modes, lines, transfers, egress modes) is large. This thesis proposes a doubly stochastic approach for generating alternative routes that are relevant to travellers, since the method allows accounting for both perceived costs of the network elements and heterogeneity......The subject of this thesis is behavioural models for route choice of passengers in multimodal public transport networks. While research in sustainable transport has dedicated much attention toward the determinants of choice between car and sustainable travel options, it has devoted less attention...

  20. Modeling real-world fuel consumption and carbon dioxide emissions with high resolution for light-duty passenger vehicles in a traffic populated city

    International Nuclear Information System (INIS)

    Zhang, Shaojun; Wu, Ye; Un, Puikei; Fu, Lixin; Hao, Jiming

    2016-01-01

    Modeling fuel consumption of light-duty passenger vehicles has created substantial concerns due to the uncertainty from real-world operating conditions. Macao is world-renowned for its tourism industry and high population density. An empirical model is developed to estimate real-world fuel consumption and carbon dioxide emissions for gasoline-powered light-duty passenger vehicles in Macao by considering local fleet configuration and operating conditions. Thanks to increasingly stringent fuel consumption limits in vehicle manufacturing countries, estimated type-approval fuel consumption for light-duty passenger vehicles in Macao by model year was reduced from 7.4 L/100 km in 1995 to 5.9 L/100 km in 2012, although a significant upsizing trend has considerably offset potential energy-saving benefit. However, lower driving speed and the air-conditioning usage tend to raise fleet-average fuel consumption and carbon dioxide emission factors, which are estimated to be 10.1 L/100 km and 240 g/km in 2010. Fleet-total fuel consumption and carbon dioxide emissions are modeled through registered vehicle population-based and link-level traffic demand approaches and the results satisfactorily coincide with the historical record of fuel sales in Macao. Temporal and spatial variations in fuel consumption and carbon dioxide emissions from light-duty passenger vehicles further highlight the importance of effective traffic management in congested areas of Macao. - Highlights: • A fuel consumption model is developed for Macao's light-duty passenger cars. • Increased vehicle size partially offset energy benefit from tightened fuel consumption standard. • Lower speed and use of air-conditioning greatly increase fuel use of Macao light-duty passenger cars. • A high resolution inventory of fuel use and carbon dioxide emissions is built with link-level traffic data. • Policy suggestions are provided to mitigate fuel use in a traffic populated city.

  1. THE AUTOMATIC SYSTEM’S MODEL OF DECISION-MAKING SUPPORT FOR DISPATCHING CONTROL OF THE CITY PASSENGER TRAFFIC

    Directory of Open Access Journals (Sweden)

    V. A. Lakhno

    2016-04-01

    Full Text Available Purpose. This scientific work considers the further development of mathematical models and algorithms for automatic decision support for dispatching management of the city passenger traffic. Methodology. Systems of dispatching management for the city passenger transport are to provide the carrying out of the routes according schedules with minimal deviations from the planned ones through the using of appropriate control actions. The systems’ algorithm focuses on the selection of control actions that compensate the disturbances. It is proposed to use the index of the waiting time minimum for passengers of buses and taxis at stops as a criterion for evaluating of dispatching control systems work. Findings. Based on the conducted analysis of the research within the existing theory of traffic flow of vehicles, it was proposed the model for the system of dispatching management for urban passenger moving units considering the effect of the most important stochastic factors on the schedule of buses and taxis movement in large cities. The obtained system of equations that models the parameter of movement on the bus routes allows you to assess quickly the influence of disturbing effects on the service quality indicators of passengers and, if necessary, to draw up the optimal schedule. Originality. The authors propose a new model for decision support of dispatching management for the city passenger transport. They take into account the effect of the most important stochastic factors, such as the overflowing buses and taxis, their descent from the lines, delays, deviations from the speed limit on the route, etc., on indicators of service quality, as well as optimizing the schedule. Practical value. The results allow to improve approaches to building models using in the systems of dispatching management of urban bus routes, as well as to improve the selection of control actions for similar systems in large cities of Ukraine.

  2. Car seat inspection among children older than 3 years: Using data to drive practice in child passenger safety.

    Science.gov (United States)

    Kroeker, Amber M; Teddy, Amy J; Macy, Michelle L

    2015-09-01

    Motor vehicle crashes are the leading cause of unintentional death and disability among children 4 years to 12 years of age in the United States. Despite the high risk of injury from motor vehicle crashes in this age group, parental awareness and child passenger safety programs in particular may lack focus on this age group. This is a retrospective cross-sectional analysis of child passenger safety seat checklist forms from two Safe Kids coalitions in Michigan (2013) to identify restraint type upon arrival to car seat inspections. Other variables were included if the coalition provided a new child safety seat and if the child had a sibling who underwent a car seat inspection. χ statistics were used to compare change in restraint use on arrival and at departure, the proportion of children attending a car seat inspection event by age, the age category of children by site, the proportion of children with siblings also undergoing a car seat inspection by age, and the distribution of a new child safety seat by age. Data were available from 1,316 Safe Kids Huron Valley and 3,215 Safe Kids Greater Grand Rapids car seat inspections. Just 10.8% of the total seats inspected were booster seats. Child safety seats for infant and young children were more commonly inspected (rear-facing carrier [40.3%], rear-facing convertible [10.2%], and forward-facing [19.3%] car seats). Few children at inspections used a seat belt only (5.4%) or had no restraint (13.8%). Children 4 years and older were found to be in a suboptimal restraint at least 30% of the time. Low proportions of parents use car seat inspections for children in the booster seat age group. The proportion of children departing the inspection in a more protective restraint increased with increasing age. This highlights an area of weakness in child passenger safety programs and signals an opportunity to strengthen efforts on The Booster Age Child. Epidemiologic/prognostic study, level III.

  3. Highway Passenger Transport Based Express Parcel Service Network Design: Model and Algorithm

    Directory of Open Access Journals (Sweden)

    Yuan Jiang

    2017-01-01

    Full Text Available Highway passenger transport based express parcel service (HPTB-EPS is an emerging business that uses unutilised room of coach trunk to ship parcels between major cities. While it is reaping more and more express market, the managers are facing difficult decisions to design the service network. This paper investigates the HPTB-EPS network design problem and analyses the time-space characteristics of such network. A mixed-integer programming model is formulated integrating the service decision, frequency, and network flow distribution. To solve the model, a decomposition-based heuristic algorithm is designed by decomposing the problem as three steps: construction of service network, service path selection, and distribution of network flow. Numerical experiment using real data from our partner company demonstrates the effectiveness of our model and algorithm. We found that our solution could reduce the total cost by up to 16.3% compared to the carrier’s solution. The sensitivity analysis demonstrates the robustness and flexibility of the solutions of the model.

  4. Applied Two-Class Overbooking Model in Thailand's Passenger Airline Data

    Directory of Open Access Journals (Sweden)

    Murati Somboon

    2017-12-01

    Full Text Available In this study, a mathematical model, which combines two of the most important airline revenue management strategies, namely overbooking and seat inventory control, is applied in Thailand's passenger airline data. Using this model, it is possible to find a closed-form solution for both the optimal booking limit and the optimal overbooking limit, simultaneously. Numerical study was set to evaluate the performance of the two-class overbooking model and to test three hypotheses using real-life data. Our two-class overbooking model outperformed the fixed-booking limit policy. Moreover, three hypotheses: the effect of varying the number of update booking limit points, the effect of an incorrect initial mean for demand, and the effect of a number of smoothing constants on an exponential smoothing method were tested using real-life data. At the 0.05 significance level, it was found that different numbers of update booking limit points affected profit, incorrect initial mean for demand did not affect profit when a high number of update booking limit points was set, and all of the smoothing constants in exponential smoothing method affected profit to some extent.

  5. Transportation Costs and Subsidy Distribution Model for Urban and Suburban Public Passenger Transport

    Directory of Open Access Journals (Sweden)

    Marko Ševrović

    2015-03-01

    Full Text Available Public transport (PT subsidy provides the means to impose the optimal combination of fare and Level of Service (LoS offered to passengers. In regions where one PT operator services multiple local communities on multiple lines it becomes hard to uniformly link the actual cost of a line and thus the LoS offered, to a particular local community. This leads to possible disproportions in the overall subsidy distribution that can result in being unfair to some local communities, mainly the ones that are sparsely populated or geographically isolated. In order to extricate this problem the appropriate level of PT subsidisation according to the average values in the European cities was investigated and the current subsidy policies in Croatia were investigated. Based on this research and the hypothesis that the offered LoS must be reflected in the subsidy amount a new subsidy distribution model was established that involves a series of analytical procedures and processes. This model introduces several factors used for the calculation of the actual share in costs. Thus, the amount of subsidies for individual lines in a region can be determined based on the actual service offered to the local community, The proposed model has been tested and successfully implemented in the Dubrovnik-Neretva County in the Republic of Croatia.

  6. Modeling and energy management control design for a fuel cell hybrid passenger bus

    Science.gov (United States)

    Simmons, Kyle; Guezennec, Yann; Onori, Simona

    2014-01-01

    This paper presents the modeling and supervisory energy management design of a hybrid fuel cell/battery-powered passenger bus. With growing concerns about petroleum usage and greenhouse gas emissions in the transportation sector, finding alternative methods for vehicle propulsion is necessary. Proton Exchange Membrane (PEM) fuel cell systems are viable possibilities for energy converters due to their high efficiencies and zero emissions. It has been shown that the benefits of PEM fuel cell systems can be greatly improved through hybridization. In this work, the challenge of developing an on-board energy management strategy with near-optimal performance is addressed by a two-step process. First, an optimal control based on Pontryagin's Minimum Principle (PMP) is implemented to find the global optimal solution which minimizes fuel consumption, for different drive cycles, with and without grade. The optimal solutions are analyzed in order to aid in development of a practical controller suitable for on-board implementation, in the form of an Auto-Regressive Moving Average (ARMA) regulator. Simulation results show that the ARMA controller is capable of achieving fuel economy within 3% of the PMP controller while being able to limit the transient demand on the fuel cell system.

  7. THE STUDY OF BRAKE SYSTEMS OF PASSENGER CARS MODEL 61-779 AND THEIR MODIFICATIONS PRODUCED BY OPEN JOINT STOCK COMPANY KRJUKIV CAR BUILDING PLANT

    Directory of Open Access Journals (Sweden)

    Yu. Ya. Vodiannikov

    2007-11-01

    Full Text Available The results of research of brake system for the model 61-779 of a passenger car manufactured by JSC «KVBZ» for the period from 2001 to 2006 are presented. It is shown that at the existing gear ratio of a brake lever transmission the passenger car brake efficiency does not correspond to running speed of 140 km/h. The causes of the wheel pairs damage occurrence in exploitation of a passenger train «Kiev – Moscow» as well as the recommendations on their elimination and brake system perfection are considered.

  8. Airline Passengers

    OpenAIRE

    Wittmer, Andreas; Hinnen, Gieri

    2016-01-01

    Airlines create value for employees, investors, governments, customers and consumers. This chapter focuses on the customers and consumers of the airline product. Airline customers, who include passengers and corporate travel providers, exert considerable market power in the air transport industry through their purchasing decisions and travel behaviour. As a purchaser of a commercial aviation product, customers are responsible for stimulating product and service innovation and their behaviour ...

  9. Telemedical Advice to Long Distance Passenger Ferries

    DEFF Research Database (Denmark)

    Jensen, Olaf Chresten; Bøggild, Niels Bo; Kristensen, Søren

    consultations with passenger ferries to identify areas for possible improvements. Methods: Data from the journals for one year from Radio Medical Denmark consultations with the medical Data from the journals for one year from Radio Medical Denmark consultations with the medical responsible officers on passenger...... ferries was analysed retrospectively. Results: Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember patients were analysed. Passenger patients were generally older and more serious ill than...

  10. Intermodal Passenger Connectivity Database -

    Data.gov (United States)

    Department of Transportation — The Intermodal Passenger Connectivity Database (IPCD) is a nationwide data table of passenger transportation terminals, with data on the availability of connections...

  11. Transient thermal model of passenger car's cabin and implementation to saturation cycle with alternative working fluids

    International Nuclear Information System (INIS)

    Lee, Hoseong; Hwang, Yunho; Song, Ilguk; Jang, Kilsang

    2015-01-01

    A transient thermal model of a passenger car's cabin is developed to investigate the dynamic behavior of cabin thermal conditions. The model is developed based on a lumped-parameter model and solved using integral methods. Solar radiation, engine heat through the firewall, and engine heat to the air ducts are all considered. Using the thermal model, transient temperature profiles of the interior mass and cabin air are obtained. This model is used to investigate the transient behavior of the cabin under various operating conditions: the recirculation mode in the idling state, the fresh air mode in the idling state, the recirculation mode in the driving state, and fresh air mode in the driving state. The developed model is validated by comparing with experimental data and is within 5% of deviation. The validated model is then applied for evaluating the mobile air conditioning system's design. The study found that a saturation cycle concept (four-stage cycle with two-phase refrigerant injection) could improve the system efficiency by 23.9% and reduce the power consumption by 19.3%. Lastly, several alternative refrigerants are applied and their performance is discussed. When the saturation cycle concept is applied, R1234yf MAC (mobile air conditioning) shows the largest COP (coefficient of performance) improvement and power consumption reduction. - Highlights: • The transient thermal model of the passenger car cabin is developed. • The developed model is validated with experimental data and showed 5% deviation. • Saturation cycle concept is applied to the developed cabin model. • There is 24% COP improvement by applying the saturation cycle concept. • R1234yf showed the highest potential when it is applied to the saturation cycle.

  12. "Good Passengers and Not Good Passengers:" Adolescent Drivers' Perceptions About Inattention and Peer Passengers.

    Science.gov (United States)

    McDonald, Catherine C; Sommers, Marilyn S

    The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the theory of planned behavior. We conducted 7 focus groups with 30 teens, ages 16-18, licensed for ≤1year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. The sample was 50% male, mean age 17.39 (SD 0.52) with mean length of licensure 173.7days (SD 109.2). Three themes emerged: 1) "Good and not good" passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. An understanding of teens' perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. Copyright © 2016 Elsevier Inc. All rights reserved.

  13. Improving public transportation systems with self-organization: A headway-based model and regulation of passenger alighting and boarding.

    Science.gov (United States)

    Carreón, Gustavo; Gershenson, Carlos; Pineda, Luis A

    2017-01-01

    The equal headway instability-the fact that a configuration with regular time intervals between vehicles tends to be volatile-is a common regulation problem in public transportation systems. An unsatisfactory regulation results in low efficiency and possible collapses of the service. Computational simulations have shown that self-organizing methods can regulate the headway adaptively beyond the theoretical optimum. In this work, we develop a computer simulation for metro systems fed with real data from the Mexico City Metro to test the current regulatory method with a novel self-organizing approach. The current model considers overall system's data such as minimum and maximum waiting times at stations, while the self-organizing method regulates the headway in a decentralized manner using local information such as the passenger's inflow and the positions of neighboring trains. The simulation shows that the self-organizing method improves the performance over the current one as it adapts to environmental changes at the timescale they occur. The correlation between the simulation of the current model and empirical observations carried out in the Mexico City Metro provides a base to calculate the expected performance of the self-organizing method in case it is implemented in the real system. We also performed a pilot study at the Balderas station to regulate the alighting and boarding of passengers through guide signs on platforms. The analysis of empirical data shows a delay reduction of the waiting time of trains at stations. Finally, we provide recommendations to improve public transportation systems.

  14. M-Health Service for Train Passengers Using Mobile GPS System: An ArchiMate Service Layer Model

    Directory of Open Access Journals (Sweden)

    MUHAMMAD SAJID

    2017-01-01

    Full Text Available EA (Enterprise Architecture is an instrument that is employed to describe the organization?s structure, business layout and operations within the IT (Information Technology environment. Different types of organizations extensively employed EA for aligning their business and operations with IT resources. EA may also be employed in non-organizational setting such as service providing agencies; rescue, medical emergency and education services. This paper suggests an EAF (Enterprise Architecture Framework for non-organizational setting by critically analyzing the top four EAs. The paper also proposes a new m-Health service model based on the mobile GPS (Global Positioning System for train/rail passengers by employing the ArchiMate modeling language and compares the proposed model with existing service providers.

  15. Equivalent Air Spring Suspension Model for Quarter-Passive Model of Passenger Vehicles

    OpenAIRE

    Abid, Haider J.; Chen, Jie; Nassar, Ameen A.

    2015-01-01

    This paper investigates the GENSIS air spring suspension system equivalence to a passive suspension system. The SIMULINK simulation together with the OptiY optimization is used to obtain the air spring suspension model equivalent to passive suspension system, where the car body response difference from both systems with the same road profile inputs is used as the objective function for optimization (OptiY program). The parameters of air spring system such as initial pressure, volume of bag, l...

  16. Open-Source Conceptual Sizing Models for the Hyperloop Passenger Pod

    Science.gov (United States)

    Chin, Jeffrey C.; Gray, Justin S.; Jones, Scott M.; Berton, Jeffrey J.

    2015-01-01

    Hyperloop is a new mode of transportation proposed as an alternative to California's high speed rail project, with the intended benefits of higher performance at lower overall costs. It consists of a passenger pod traveling through a tube under a light vacuum and suspended on air bearings. The pod travels up to transonic speeds resulting in a 35 minute travel time between the intended route from Los Angeles and San Francisco. Of the two variants outlined, the smaller system includes a 1.1 meter tall passenger capsule traveling through a 2.2 meter tube at 700 miles per hour. The passenger pod features water-based heat exchangers as well as an on-board compression system that reduces the aerodynamic drag as it moves through the tube. Although the original proposal looks very promising, it assumes that tube and pod dimensions are independently sizable without fully acknowledging the constraints of the compressor system on the pod geometry. This work focuses on the aerodynamic and thermodynamic interactions between the two largest systems; the tube and the pod. Using open-source toolsets, a new sizing method is developed based on one-dimensional thermodynamic relationships that accounts for the strong interactions between these sub-systems. These additional considerations require a tube nearly twice the size originally considered and limit the maximum pod travel speed to about 620 miles per hour. Although the results indicate that Hyperloop will need to be larger and slightly slower than originally intended, the estimated travel time only increases by approximately five minutes, so the overall performance is not dramatically affected. In addition, the proposed on-board heat exchanger is not an ideal solution to achieve reasonable equilibrium air temperatures within the tube. Removal of this subsystem represents a potential reduction in weight, energy requirements and complexity of the pod. In light of these finding, the core concept still remains a compelling

  17. Identification and analysis of explanatory variables for a multi-factor productivity model of passenger airlines

    Directory of Open Access Journals (Sweden)

    Antonio Henriques de Araújo Jr

    2011-05-01

    Full Text Available The paper aimed to identify and analyze the explanatory variables for airlines productivity during 2000 2005, by testing the Pearson correlation between the single factor productivity capital, energy and labor of a sample of 45 selected international airlines (4 Brazilian carriers among them and their productivity explanatory variables like medium stage length, aircraft load factor, hours flown and cruise speed for selected routes besides aircraft seat configuration and airlines number of employees. The research demonstrated, that a set of variables can explain differences in productivity for passenger airlines, such as: investment in personnel training processes, automation, airplane seat density, occupation of aircraft, average flight stage length, density and extension of routes, among others.

  18. Equivalent Air Spring Suspension Model for Quarter-Passive Model of Passenger Vehicles.

    Science.gov (United States)

    Abid, Haider J; Chen, Jie; Nassar, Ameen A

    2015-01-01

    This paper investigates the GENSIS air spring suspension system equivalence to a passive suspension system. The SIMULINK simulation together with the OptiY optimization is used to obtain the air spring suspension model equivalent to passive suspension system, where the car body response difference from both systems with the same road profile inputs is used as the objective function for optimization (OptiY program). The parameters of air spring system such as initial pressure, volume of bag, length of surge pipe, diameter of surge pipe, and volume of reservoir are obtained from optimization. The simulation results show that the air spring suspension equivalent system can produce responses very close to the passive suspension system.

  19. Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

    Science.gov (United States)

    Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

    2016-01-01

    Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

  20. Young drivers and their young passengers.

    NARCIS (Netherlands)

    2015-01-01

    More than one-third of all fatalities among car passengers occurs in the 10-24-year age group. The majority of these young passengers die in a car driven by an 18 to 24-year old. Compared with the composition of the population, these are high proportions, yet the exposure (for example in distance

  1. Modelling the resilience of rail passenger transport networks affected by large-scale disruptive events : the case of HSR (high speed rail)

    NARCIS (Netherlands)

    Janic, M.

    2018-01-01

    This paper deals with modelling the dynamic resilience of rail passenger transport networks affected by large-scale disruptive events whose impacts deteriorate the networks’ planned infrastructural, operational, economic, and social-economic performances represented by the selected indicators.

  2. Simulating the impact of policy, energy prices and technological progress on the passenger car fleet in Austria-A model based analysis 2010-2050

    International Nuclear Information System (INIS)

    Kloess, Maximilian; Mueller, Andreas

    2011-01-01

    This paper investigates the effects of policy, fuel prices and technological progress on the Austrian passenger car fleet in terms of energy consumption and greenhouse gas (GHG) emissions. To analyse these effects a simulation model is used. We model the car fleet from a bottom-up perspective, with a detailed coverage of vehicle specifications and propulsion technologies. The model focuses on the technological trend toward electrified propulsion systems and their potential effects on the fleet's energy consumption and GHG emissions. To represent the impact of prices and income on the development of the fleet, we combine the fleet model with top-down demand models. We developed two scenarios for the time frame 2010-2050, using two different sets of assumptions for regulatory development and conditions of increasing fossil fuel prices and continuous technological progress in vehicle propulsion technologies. The results indicate that material cuts in energy consumption and GHG emissions can be achieved with changes to the political framework for passenger cars. Appropriate taxation of fuels and cars can stabilise demand for individual motorised transport and lead to an improvement in vehicle efficiency by fostering the adoption of efficient vehicle propulsion technologies and low carbon fuels. - Highlights: → We present a simulation model for future energy demand and greenhouse gas emissions in passenger car transport. → We develop scenarios up to 2050 assuming two different policy schemes. → Policy strongly affects energy demand and greenhouse gas emissions in passenger car transport. → Policy can slow down growth in demand for passenger car transport. → Policy can promote the diffusion of more efficient propulsion technologies and low carbon fuels.

  3. Automotive Maintenance Data Base for Model Years 1976-1979. Part II : Appendix E and F

    Science.gov (United States)

    1980-12-01

    An update of the existing data base was developed to include life cycle maintenance costs of representative vehicles for the model years 1976-1979. Repair costs as a function of time are also developed for a passenger car in each of the compact, subc...

  4. Automotive Maintenance Data Base for Model Years 1976-1979. Part I

    Science.gov (United States)

    1980-12-01

    An update of the existing data base was developed to include life cycle maintenance costs of representative vehicles for the model years 1976-1979. Repair costs as a function of time are also developed for a passenger car in each of the compact, subc...

  5. Passengers, Information, and Disruptions

    NARCIS (Netherlands)

    E. van der Hurk (Evelien)

    2015-01-01

    markdownabstract__Abstract__ Passengers traveling in public transport generate a detailed digital track record of their journey through using automated fare collection systems and carrying mobile devices. This information on passenger behavior has only recently become available to public

  6. Radiation Exposure of Passengers to Cosmic Radiation

    International Nuclear Information System (INIS)

    Salah El-Din, T.; Gomaa, M.A.; Sallah, N.

    2010-01-01

    The main aim of the present study is to review exposure of Egyptian passengers and occupational workers to cosmic radiation during their work. Computed effective dose of passengers by computer code CARI-6 using during either short route, medium route or long route as well as recommended allowed number of flights per year

  7. The modeling of attraction characteristics regarding passenger flow in urban rail transit network based on field theory.

    Science.gov (United States)

    Li, Man; Wang, Yanhui; Jia, Limin

    2017-01-01

    Aimed at the complicated problems of attraction characteristics regarding passenger flow in urban rail transit network, the concept of the gravity field of passenger flow is proposed in this paper. We establish the computation methods of field strength and potential energy to reveal the potential attraction relationship among stations from the perspective of the collection and distribution of passenger flow and the topology of network. As for the computation methods of field strength, an optimum path concept is proposed to define betweenness centrality parameter. Regarding the computation of potential energy, Compound Simpson's Rule Formula is applied to get a solution to the function. Taking No. 10 Beijing Subway as a practical example, an analysis of simulation and verification is conducted, and the results shows in the following ways. Firstly, the bigger field strength value between two stations is, the stronger passenger flow attraction is, and the greater probability of the formation of the largest passenger flow of section is. Secondly, there is the greatest passenger flow volume and circulation capacity between two zones of high potential energy.

  8. The modeling of attraction characteristics regarding passenger flow in urban rail transit network based on field theory.

    Directory of Open Access Journals (Sweden)

    Man Li

    Full Text Available Aimed at the complicated problems of attraction characteristics regarding passenger flow in urban rail transit network, the concept of the gravity field of passenger flow is proposed in this paper. We establish the computation methods of field strength and potential energy to reveal the potential attraction relationship among stations from the perspective of the collection and distribution of passenger flow and the topology of network. As for the computation methods of field strength, an optimum path concept is proposed to define betweenness centrality parameter. Regarding the computation of potential energy, Compound Simpson's Rule Formula is applied to get a solution to the function. Taking No. 10 Beijing Subway as a practical example, an analysis of simulation and verification is conducted, and the results shows in the following ways. Firstly, the bigger field strength value between two stations is, the stronger passenger flow attraction is, and the greater probability of the formation of the largest passenger flow of section is. Secondly, there is the greatest passenger flow volume and circulation capacity between two zones of high potential energy.

  9. Demand modelling of passenger air travel: An analysis and extension, volume 2

    Science.gov (United States)

    Jacobson, I. D.

    1978-01-01

    Previous intercity travel demand models in terms of their ability to predict air travel in a useful way and the need for disaggregation in the approach to demand modelling are evaluated. The viability of incorporating non-conventional factors (i.e. non-econometric, such as time and cost) in travel demand forecasting models are determined. The investigation of existing models is carried out in order to provide insight into their strong points and shortcomings. The model is characterized as a market segmentation model. This is a consequence of the strengths of disaggregation and its natural evolution to a usable aggregate formulation. The need for this approach both pedagogically and mathematically is discussed. In addition this volume contains two appendices which should prove useful to the non-specialist in the area.

  10. Divers of Passenger Demand

    OpenAIRE

    Wittmer, Andreas

    2011-01-01

    -Overview drivers of passenger demand -Driver 1: Economic growth in developing countries -Driver 2: International business travel in developed countries -Driver 3: International leisure travel in developed countries

  11. Nonlinear model predictive control of a passenger vehicle for automated lane changes

    NARCIS (Netherlands)

    Acosta, A.F.; Marquez-Ruiz, A.; Espinosa, J.J.

    2017-01-01

    This article presents a nonlinear Model Predictive Control (MPC) for lane changes, based on a simplified Single Track Model (STM) of the vehicle. The STM includes the position of the vehicle in global coordinates as a state so that the position of the target lane can be specified to the MPC for

  12. Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method.

    Science.gov (United States)

    Zhang, Hongshen; Chen, Ming

    2013-11-01

    In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Demand modelling of passenger air travel: An analysis and extension. Volume 1: Background and summary

    Science.gov (United States)

    Jacobson, I. D.

    1978-01-01

    The framework for a model of travel demand which will be useful in predicting the total market for air travel between two cities is discussed. Variables to be used in determining the need for air transportation where none currently exists and the effect of changes in system characteristics on attracting latent demand are identified. Existing models are examined in order to provide insight into their strong points and shortcomings. Much of the existing behavioral research in travel demand is incorporated to allow the inclusion of non-economic factors, such as convenience. The model developed is characterized as a market segmentation model. This is a consequence of the strengths of disaggregation and its natural evolution to a usable aggregate formulation. The need for this approach both pedagogically and mathematically is discussed.

  14. THE MATHEMATICAL MODEL OF SELECTING THE ROLLING STOCK FOR PASSENGER BUS TRANSPORTATION

    Directory of Open Access Journals (Sweden)

    M. Kostikova

    2017-06-01

    Full Text Available The problem of choosing buses of different carrying capacity while simultaneously using them on regular urban routes is considered. The indicators that affect the selection of the rolling stock are analyzed. Methods for constructing models, which allow calculating the number of buses of different classes for one city route are proposed. The implementation of the constructed models will make it possible to obtain the savings in capital expenditures, as well as reduce the operational costs of an enterprise.

  15. Decomposing passenger transport futures : Comparing results of global integrated assessment models

    NARCIS (Netherlands)

    Edelenbosch, O. Y.; McCollum, D. L.; van Vuuren, Detlef; Bertram, C.; Carrara, S.; Daly, H.; Fujimori, S.; Kitous, A.; Kyle, P.; Ó Broin, E.; Karkatsoulis, P.; Sano, F.

    The transport sector is growing fast in terms of energy use and accompanying greenhouse gas emissions. Integrated assessment models (IAMs) are used widely to analyze energy system transitions over a decadal time frame to help inform and evaluating international climate policy. As part of this, IAMs

  16. Fractional order modeling and control of dissimilar redundant actuating system used in large passenger aircraft

    Directory of Open Access Journals (Sweden)

    Salman IJAZ

    2018-05-01

    Full Text Available In this paper, a methodology has been developed to address the issue of force fighting and to achieve precise position tracking of control surface driven by two dissimilar actuators. The nonlinear dynamics of both actuators are first approximated as fractional order models. Based on the identified models, three fractional order controllers are proposed for the whole system. Two Fractional Order PID (FOPID controllers are dedicated to improving transient response and are designed in a position feedback configuration. In order to synchronize the actuator dynamics, a third fractional order PI controller is designed, which feeds the force compensation signal in position feedback loop of both actuators. Nelder-Mead (N-M optimization technique is employed in order to optimally tune controller parameters based on the proposed performance criteria. To test the proposed controllers according to real flight condition, an external disturbance of higher amplitude that acts as airload is applied directly on the control surface. In addition, a disturbance signal function of system states is applied to check the robustness of proposed controller. Simulation results on nonlinear system model validated the performance of the proposed scheme as compared to optimal PID and high gain PID controllers. Keywords: Aerospace, Fractional order control, Model identification, Nelder-Mead optimization, Robustness

  17. “Good passengers and not good passengers:” Adolescent drivers’ perceptions about inattention and peer passengers

    Science.gov (United States)

    Sommers, Marilyn S.

    2016-01-01

    Purpose The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. Design & Methods We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the Theory of Planned Behavior. We conducted 7 focus groups with 30 teens, ages 16–18, licensed for ≤1 year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. Results The sample was 50% male, mean age 17.39 (sd 0.52) with mean length of licensure 173.7 days (sd 109.2). Three themes emerged: 1) “Good and not good” passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. Conclusions While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. Practical Implications An understanding of teens’ perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. PMID:27496828

  18. Commuter Train Passenger Safety Model Using Positive Behavior Approach: The Case Study in Suburban Area

    Science.gov (United States)

    Suryanto, D. A.; Adisasmita, S. A.; Hamid, S.; Hustim, M.

    2018-04-01

    Currently, Train passanger safety measures are more predominantly measurable using negative dimensions in user mode behavior, such as accident rate, accident intensity and accident impact. This condition suggests that safety improvements aim only to reduce accidents. Therefore, this study aims to measure the safety level of light train transit modes (KRL) through the dimensions of traveling safety on commuters based on positive safety indicators with severel condition departure times and returns for work purposes and long trip rates above KRL. The primary survey were used in data collection methods. Structural Equation Modeling (SEM) were used in data analysis. The results show that there are different models of the safety level of departure and return journey. The highest difference is in the security dimension which is the internal variable of KRL users.

  19. Rail passengers rights

    Directory of Open Access Journals (Sweden)

    Đurđev Dušanka J.

    2016-01-01

    Full Text Available The legal framework of rail passengers rights is set out in a combination of international and European law: an international measure, the rather unwieldy Uniform Rules concerning the Contract for International Carriage of Passengers and Luggage by Rail, forming part of the Convention concerning International Carriage by Rail of 9 May 1980 (as amended by the Vilnius Protocol of 3 June 1999 ['CIV'], lays down a basic framework which is then fleshed out by more recent EU legislation, Regulation (EC No 1371/2007 on Rail Passengers ' Rights and Obligations. Regulation 1371/2007/EC on rail passenger rights and obligations sets out minimum quality standards that have to be guaranteed to all passengers on all lines. .

  20. Multimodal route choice models of public transport passengers in the Greater Copenhagen Area

    DEFF Research Database (Denmark)

    Anderson, Marie Karen; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2014-01-01

    Understanding route choice behavior is crucial to explain travelers’ preferences and to predict traffic flows under different scenarios. A growing body of literature has concentrated on public transport users without, however, concentrating on multimodal public transport networks because......,641 public transport users in the Greater Copenhagen Area.A two-stage approach consisting of choice set generation and route choice model estimation allowed uncovering the preferences of the users of this multimodal large-scale public transport network. The results illustrate the rates of substitution...... not only of the in-vehicle times for different public transport modes, but also of the other time components (e.g., access, walking, waiting, transfer) composing the door-to-door experience of using a multimodal public transport network, differentiating by trip length and purpose, and accounting...

  1. PASSENGER FLOWS PREDICTION IN MAJOR TRANSPORTATION HUBS

    Directory of Open Access Journals (Sweden)

    O. O. Ozerova

    2013-11-01

    Full Text Available Purpose. An effective organization of passenger traffic, due to the reliability prediction of traffic flow in passenger transport hubs. In order to determine the parameters of prospective passenger transport areas it is essential to analyze the impact of various factors and determine the most influential ones. Methodology. The article presents the method of paired linear correlation for a more influential factors on passengers in intercity and commuter and possible use in predicting the linear regression equations. Passenger transport vessel areas and branches of industry are interconnected and are in the ratio of passengers and production. Findings. It is found that the coefficient of correlation is in complex dependence on the duration of the period of retrospective analysis. Evaluation of reliability correlation coefficients and coefficients of predictive models led to the conclusion that the population gives the most accurate prediction of passenger flows, providing account of changes in Ukraine during the period of transformation. Originality. Equations of dependence on the impact of macroeconomic indicators were obtained and the evaluation of the reliability results was received. Practical value. The results of analysis and calculations will make short-term forecasting of traffic flow.

  2. A data mining approach to investigate the factors influencing the crash severity of motorcycle pillion passengers.

    Science.gov (United States)

    Tavakoli Kashani, Ali; Rabieyan, Rahim; Besharati, Mohammad Mehdi

    2014-12-01

    Motorcycle passengers comprise a considerable proportion of traffic crash victims. During a 5 year period (2006-2010) in Iran, an average of 3.4 pillion passengers are killed daily due to motorcycle crashes. This study investigated the main factors influencing crash severity of this group of road users. The Classification and Regression Trees (CART) method was employed to analyze the injury severity of pillion passengers in Iran over a 4 y ear period (2009-2012). The predictive accuracy of the model built with a total of 16 variables was 74%, which showed a considerable improvement compared to previous studies. The results indicate that area type, land use, and injured part of the body (head, neck, etc.) are the most influential factors affecting the fatality of motorcycle passengers. Results also show that helmet usage could reduce the fatality risk among motorcycle passengers by 28%. The findings of this study might help develop more targeted countermeasures to reduce the death rate of motorcycle pillion passengers. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Optimal boarding method for airline passengers

    Energy Technology Data Exchange (ETDEWEB)

    Steffen, Jason H.; /Fermilab

    2008-02-01

    Using a Markov Chain Monte Carlo optimization algorithm and a computer simulation, I find the passenger ordering which minimizes the time required to board the passengers onto an airplane. The model that I employ assumes that the time that a passenger requires to load his or her luggage is the dominant contribution to the time needed to completely fill the aircraft. The optimal boarding strategy may reduce the time required to board and airplane by over a factor of four and possibly more depending upon the dimensions of the aircraft. I explore some features of the optimal boarding method and discuss practical modifications to the optimal. Finally, I mention some of the benefits that could come from implementing an improved passenger boarding scheme.

  4. Network structure of subway passenger flows

    Science.gov (United States)

    Xu, Q.; Mao, B. H.; Bai, Y.

    2016-03-01

    The results of transportation infrastructure network analyses have been used to analyze complex networks in a topological context. However, most modeling approaches, including those based on complex network theory, do not fully account for real-life traffic patterns and may provide an incomplete view of network functions. This study utilizes trip data obtained from the Beijing Subway System to characterize individual passenger movement patterns. A directed weighted passenger flow network was constructed from the subway infrastructure network topology by incorporating trip data. The passenger flow networks exhibit several properties that can be characterized by power-law distributions based on flow size, and log-logistic distributions based on the fraction of boarding and departing passengers. The study also characterizes the temporal patterns of in-transit and waiting passengers and provides a hierarchical clustering structure for passenger flows. This hierarchical flow organization varies in the spatial domain. Ten cluster groups were identified, indicating a hierarchical urban polycentric structure composed of large concentrated flows at urban activity centers. These empirical findings provide insights regarding urban human mobility patterns within a large subway network.

  5. Delay Management with Re-Routing of Passengers

    NARCIS (Netherlands)

    T.A.B. Dollevoet (Twan); D. Huisman (Dennis); M.E. Schmidt (Marie); A. Schöbel (Anita)

    2010-01-01

    textabstractThe question of delay management is whether trains should wait for a delayed feeder train or should depart on time. In classical delay management models passengers always take their originally planned route. In this paper, we propose a model where re-routing of passengers is

  6. International Passenger and Freight Report

    Data.gov (United States)

    Department of Transportation — The International Passenger and Freight report is a summarization of all passengers and all freight transported between the U.S. and foreign countries combined, with...

  7. Model-based design of active vibration compensation in the passenger car powertrain; Modellbasierte Auslegung der aktiven Schwingungskompensation im Kfz-Antriebsstrang

    Energy Technology Data Exchange (ETDEWEB)

    Quernheim, L.

    2008-07-01

    Modern passenger cars have increasingly higher driving torques while the rotary mass of the powertrain is reduced. This induces vibrations. Especially during load change operations, the driving comfort may therefore be impaired by jolting. To reduce these vibrations, the engine control unit has integrated control functions that influence the driving characteristics. Until now, these control functions were adjusted empirically by the application engineer during time-consuming test drives, but this option is failing as development times are getting shorter while there are increasing numbers of car lines. The author therefore presents a new option, i.e. optimisation of the comfort functions by means of model-based control unit design. The example of an active vibration damper is presented to illustrate this model-based procedure, and vehicle analyses were carried out with the intention to show that this method supports the application engineer in his work efficiently. (orig.)

  8. Mortality of German travellers on passenger vessels.

    Science.gov (United States)

    Oldenburg, Marcus; Herzog, Jan; Püschel, Klaus; Harth, Volker

    2016-01-01

    In the past two decades, more and more Germans decided to spend their holidays on a passenger vessel. This study examined the frequencies and causes of deaths of German travellers aboard passenger vessels of all flags. The shipboard deaths of all German travellers within the time period from 1998 to 2008 were counted using the German civil central register in Berlin. The available documentation in this register provides information on frequencies, circumstances and causes of deaths on ships. In the above-mentioned period of time, the total cohort of German travellers on cruise ships is estimated to be 5.97 million persons. During the 11-year examination period, 135 shipboard deaths of German passengers [102 males (75.6%) and 33 females (24.4%)] were recorded. Out of these travellers, 110 died on cruise ships. When considering only the passengers on cruise ships (without those on ferries) an average crude mortality rate of 1.8 per 100,000 German passengers was calculated. The crude mortality rate of shipboard death for males and females was 2.5 and 0.8 per 100,000 German passengers with a mean age of 71.2 years [standard deviation (SD) 16.0 years] and 73.3 years (SD 16.0 years), respectively. Significantly, more deceased travellers older than 70 years were observed on traditional cruise ships and resort vessels than on passenger ferries (P = 0.001). The causes of death were documented in 85 cases (63.0%). Out of these documented deaths, 82 (96.5%) cases were regarded to be natural causes (particularly circulatory diseases) and 3 (3.5%) as unnatural causes (twice drowning and once an accidental fall). In spite of the large proportion of unknown causes of death, this study argues for a high significance of internal causes of deaths among German passengers. Thus, ship's doctors-particularly those on traditional cruise ships-should be well experienced in internal and geriatric medicines. © The Author 2016. Published by Oxford University Press on behalf of

  9. Operations Research in PassengerRaiway Transportation

    NARCIS (Netherlands)

    D. Huisman (Dennis); L.G. Kroon (Leo); R.M. Lentink (Ramon); M.J.C.M. Vromans (Michiel)

    2005-01-01

    textabstractIn this paper we give an overview of state-of-the-art Operations Research models and techniques used in passenger railway transportation. For each planning phase (strategic, tactical and operational), we describe the planning problems arising there and discuss some models and algorithms

  10. Deduction of passengers' route choice from smart card data

    NARCIS (Netherlands)

    Van Der Hurk, Evelien; Kroon, Leo; Maroti, Gabor; Vervest, Peter

    2013-01-01

    Deducing passengers' route choice from smart card data provides public transport operators the opportunity to evaluate passenger service. Especially in case of disruptions when route choice models may not be valid this is an advantage. This paper proposes a method for deducing the chosen route of

  11. Deduction of passengers' route choices from smart card data

    NARCIS (Netherlands)

    van der Hurk, E.; Kroon, L.G.; Maroti, G.; Vervest, P.

    2015-01-01

    Deducing passengers' route choices from smart card data provides public transport operators the opportunity to evaluate and improve their passenger service. Particularly in the case of disruptions, when traditional route choice models may not be valid, this is an advantage. This paper proposes a

  12. CONCEPTUAL APPROACHES TO CREATE CONTROL MECHANISM BY PASSENGER COMMUTATION SERVICES

    Directory of Open Access Journals (Sweden)

    V. O. Zadoya

    2010-11-01

    Full Text Available In the article the basic approaches of improving a management mechanism for passenger suburban railway transportations are considered, and the classification of reformation models for passenger suburban railway transportations depending on scales, degree of independence, department subordination and amount of proprietors of future company is offered.

  13. Passenger safety, health, and comfort: a review.

    Science.gov (United States)

    Rayman, R B

    1997-05-01

    Since the birth of aviation medicine approximately 80 yrs ago, practitioners and scientists have given their attention primarily to flight deck crew, cabin crew, and ground support personnel. However, in more recent years we have broadened our horizons to include the safety, health, and comfort of passengers flying commercial aircraft. This will be even more compelling as more passengers take to the air in larger aircraft and flying longer hours to more distant destinations. Further, we can expect to see more older passengers because people in many countries are living longer, healthier lives. The author first discusses the stresses imposed by ordinary commercial flight upon travelers such as airport tumult, barometric pressure changes, immobility, jet lag, noise/ vibration, and radiation. Medical considerations are next addressed describing inflight illness and medical care capability aboard U.S. air carriers. Passenger safety, cabin air quality, and the preventive medicine aspects of air travel are next reviewed in the context of passenger safety, health, and comfort. Recommendations are addressed to regulator agencies, airlines aircraft manufacturers, and the aerospace medicine community.

  14. Methods to estimate railway capacity and passenger delays

    DEFF Research Database (Denmark)

    Landex, Alex

    that an evaluation of passenger delays obtained with simulation software (in this case RailSys) and the passenger delay model is comparable with the daily operation of the Copenhagen suburban railway network. Using a microscopic simulation model, the thesis demonstrates that it is possible to compare travel times...... of additional travel time. The differences between the different kinds of delay (train delays, passenger delays and scheduled waiting time) are illustrated through simple, but representative, case examples in CHAPTER 10. The examples demonstrate that 3rd generation passenger delay models are more realistic than...... depend on the given infrastructure and timetable and can result in longer travel times for trains and passengers. Furthermore, the thesis shows that the network effects can result in reduced capacity as some trains or train services can make it impossible to operate other planned/desired trains or train...

  15. Drastic population fluctuations explain the rapid extinction of the passenger pigeon.

    Science.gov (United States)

    Hung, Chih-Ming; Shaner, Pei-Jen L; Zink, Robert M; Liu, Wei-Chung; Chu, Te-Chin; Huang, Wen-San; Li, Shou-Hsien

    2014-07-22

    To assess the role of human disturbances in species' extinction requires an understanding of the species population history before human impact. The passenger pigeon was once the most abundant bird in the world, with a population size estimated at 3-5 billion in the 1800s; its abrupt extinction in 1914 raises the question of how such an abundant bird could have been driven to extinction in mere decades. Although human exploitation is often blamed, the role of natural population dynamics in the passenger pigeon's extinction remains unexplored. Applying high-throughput sequencing technologies to obtain sequences from most of the genome, we calculated that the passenger pigeon's effective population size throughout the last million years was persistently about 1/10,000 of the 1800's estimated number of individuals, a ratio 1,000-times lower than typically found. This result suggests that the passenger pigeon was not always super abundant but experienced dramatic population fluctuations, resembling those of an "outbreak" species. Ecological niche models supported inference of drastic changes in the extent of its breeding range over the last glacial-interglacial cycle. An estimate of acorn-based carrying capacity during the past 21,000 y showed great year-to-year variations. Based on our results, we hypothesize that ecological conditions that dramatically reduced population size under natural conditions could have interacted with human exploitation in causing the passenger pigeon's rapid demise. Our study illustrates that even species as abundant as the passenger pigeon can be vulnerable to human threats if they are subject to dramatic population fluctuations, and provides a new perspective on the greatest human-caused extinction in recorded history.

  16. 150 Passenger Commercial Aircraft

    Science.gov (United States)

    Bucovsky, Adrian; Romli, Fairuz I.; Rupp, Jessica

    2002-01-01

    It has been projected that the need for a short-range mid-sized, aircraft is increasing. The future strategy to decrease long-haul flights will increase the demand for short-haul flights. Since passengers prefer to meet their destinations quickly, airlines will increase the frequency of flights, which will reduce the passenger load on the aircraft. If a point-to-point flight is not possible, passengers will prefer only a one-stop short connecting flight to their final destination. A 150-passenger aircraft is an ideal vehicle for these situations. It is mid-sized aircraft and has a range of 3000 nautical miles. This type of aircraft would market U.S. domestic flights or inter-European flight routes. The objective of the design of the 150-passenger aircraft is to minimize fuel consumption. The configuration of the aircraft must be optimized. This aircraft must meet CO2 and NOx emissions standards with minimal acquisition price and operating costs. This report contains all the work that has been performed for the completion of the design of a 150 passenger commercial aircraft. The methodology used is the Technology Identification, Evaluation, and Selection (TIES) developed at Georgia Tech Aerospace Systems Design laboratory (ASDL). This is an eight-step conceptual design process to evaluate the probability of meeting the design constraints. This methodology also allows for the evaluation of new technologies to be implemented into the design. The TIES process begins with defining the problem with a need established and a market targeted. With the customer requirements set and the target values established, a baseline concept is created. Next, the design space is explored to determine the feasibility and viability of the baseline aircraft configuration. If the design is neither feasible nor viable, new technologies can be implemented to open up the feasible design space and allow for a plausible solution. After the new technologies are identified, they must be evaluated

  17. High-Speed Train Stop-Schedule Optimization Based on Passenger Travel Convenience

    OpenAIRE

    Dingjun Chen; Shaoquan Ni; Chang’an Xu; Hongxia Lv; Simin Wang

    2016-01-01

    The stop-schedules for passenger trains are important to the operation planning of high-speed trains, and they decide the quality of passenger service and the transportation efficiency. This paper analyzes the specific manifestation of passenger travel convenience and proposes the concepts of interstation accessibility and degree of accessibility. In consideration of both the economic benefits of railway corporations and the travel convenience of passengers, a multitarget optimization model i...

  18. Fleet Compliance Annual Report: Model Year 2015, Fiscal Year 2016

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-12-01

    The U.S. Department of Energy (DOE) regulates covered state government and alternative fuel provider fleets, pursuant to the Energy Policy Act of 1992 (EPAct), as amended. This report details compliance for model year 2015, fiscal year 2016.

  19. Telemedical advice to long-distance passenger ferries

    DEFF Research Database (Denmark)

    Jensen, Olaf C; Bo Bøggild, Niels; Kristensen, Søren

    2005-01-01

    BACKGROUND: Radio medical (RM) advice for seafarers and traveling passengers is important and can be crucial for the optimal medical treatment on board ships. The aim of this study was to analyze the data from consultations with passenger ferries to identify areas for possible improvements. METHODS......: Data from the journals for 1 year from Radio Medical Denmark consultations with the medical officers on passenger ferries were analyzed retrospectively. RESULTS: Two hundred fourteen RM records, 73% pertaining to passengers and 27% for crew members, were analyzed. Passenger patients were generally...... complaints, and more than half of these involved severe or considerable pain. Only acetaminophen (paracetamol) and opioids were in the ferry medicine chest. At least 77 patients would have benefited from use of nonsteroidal anti-inflammatory drugs. CONCLUSIONS: The paramedical assistance and the medicine...

  20. Manikin families representing obese airline passengers in the US.

    Science.gov (United States)

    Park, Hanjun; Park, Woojin; Kim, Yongkang

    2014-01-01

    Aircraft passenger spaces designed without proper anthropometric analyses can create serious problems for obese passengers, including: possible denial of boarding, excessive body pressures and contact stresses, postural fixity and related health hazards, and increased risks of emergency evacuation failure. In order to help address the obese passenger's accommodation issues, this study developed male and female manikin families that represent obese US airline passengers. Anthropometric data of obese individuals obtained from the CAESAR anthropometric database were analyzed through PCA-based factor analyses. For each gender, a 99% enclosure cuboid was constructed, and a small set of manikins was defined on the basis of each enclosure cuboid. Digital human models (articulated human figures) representing the manikins were created using a human CAD software program. The manikin families were utilized to develop design recommendations for selected aircraft seat dimensions. The manikin families presented in this study would greatly facilitate anthropometrically accommodating large airline passengers.

  1. The importance of high vehicle power for passenger car emissions

    Science.gov (United States)

    Carslaw, David C.; Williams, Martin L.; Tate, James E.; Beevers, Sean D.

    2013-04-01

    In this paper we use a quantile regression technique to explore the emissions characteristics of petrol and diesel passenger cars to reveal the importance of high vehicle power on exhaust emissions. A large database of ≈67,000 passenger cars from vehicle emission remote sensing data was used from surveys from several campaigns around the UK. Most previous remote sensing studies have focused on presenting mean emission estimates by vehicle type over time. However, as shown in the current work, considerably more insight can be gained into vehicle emission characteristics if techniques are used that can describe and model the full distribution of vehicle emissions as a function of important explanatory variables. For post-2000 model year (Euro 3-5) diesel cars it is shown that there is a strong dependence of vehicle specific power for emissions of NOx that was absent in earlier models and is absent for other pollutants such as CO, hydrocarbons and 'smoke'. Furthermore, we also find a stronger dependence on vehicle specific power for older catalyst-equipped petrol vehicles (Euro 1/2) on emissions of NOx that is less important for other emissions such as CO and hydrocarbons. Moreover, it is shown that while the rated maximum power output of petrol cars has remained almost constant over the past 15-20 years, the power output from diesel cars has increased markedly by about 50%. These results suggest that changes to vehicle technology, driving conditions and driver behaviour have become more important determinants of passenger car NOx emissions in recent years and may help explain why urban ambient concentrations of NOx have not decreased as much as anticipated.

  2. Simulation to assess the efficacy of US airport entry scrreening of passengers for pandemic influenza

    Energy Technology Data Exchange (ETDEWEB)

    Mcmahon, Benjamin [Los Alamos National Laboratory

    2009-01-01

    We present our methodology and stochastic discrete-event simulation developed to model the screening of passengers for pandemic influenza at the US port-of-entry airports. Our model uniquely combines epidemiology modelling, evolving infected states and conditions of passengers over time, and operational considerations of screening in a single simulation. The simulation begins with international aircraft arrivals to the US. Passengers are then randomly assigned to one of three states -- not infected, infected with pandemic influenza and infected with other respiratory illness. Passengers then pass through various screening layers (i.e. pre-departure screening, en route screening, primary screening and secondary screening) and ultimately exit the system. We track the status of each passenger over time, with a special emphasis on false negatives (i.e. passengers infected with pandemic influenza, but are not identified as such) as these passengers pose a significant threat as they could unknowingly spread the pandemic influenza virus throughout our nation.

  3. Increasing the availability of urban passenger transport on objective ...

    African Journals Online (AJOL)

    Increasing the availability of urban passenger transport on objective control data ... mathematical modeling, probability theory and mathematical statistics, expert ... intended for development of methods and means of operative management of ...

  4. Getting passengers out : evacuation behaviours

    NARCIS (Netherlands)

    Boer, L.C.

    2003-01-01

    When disaster strikes, mass transportation means mass evacuation. The issue is especially urgent if, despite precautions, a train comes to a stop in a tunnel and there is a fire. Adequate behaviour of passengers is a major success factor of an evacuation. Passengers should replace their original

  5. THE GRAPHICAL MODELING, SIMULATION AND REALIZATION OF AN EQUIPMENT WITH OPTO-REFLECTIVE SENSORS FOR THE MANAGEMENT OF URBAN PUBLIC TRANSPORT PASSENGERS

    Directory of Open Access Journals (Sweden)

    CRIȘAN Horea George

    2015-06-01

    Full Text Available The development of an equipment capable to carry out a real-time evaluation above loading of urban buses, allows the optimization of the urban transport vehicles distribution on a network segment, reducing waiting times, the passenger crowds in buses and at the same time decreasing the need of buses maintenance, issues with direct effects on the growth of the carriers economic profit. A solution based on optical detection is one that can generate results with high accuracy in relatively low cost conditions. This advantage can be obtained only if the constructive version of the equipment is properly designed, taking into account the geometric parameters of the light slots emitted and received by the sensors. Therefore, using three-dimensional CAD modelling, it was realized an optimal constructive variant. This graphical method also allows it the viewing, variation and synchronization of sensors geometrical parameters, so in this way, the equipment can produce the desired effect. Further, it has been carried out a graphical simulation of the designed equipment function, in order to validate the obtained results. Later, the designed equipment was achieved and tested under laboratory conditions, in order to be implemented and used under real conditions, on the buses of an urban public transport operator.

  6. The Simultaneous Vehicle Scheduling and Passenger Service Problem

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann; Larsen, Allan; Madsen, Oli B.G.

    2013-01-01

    , by modifying the timetable. The planning approach is referred to as the simultaneous vehicle scheduling and passenger service problem (SVSPSP). The SVSPSP is modelled as an integer programming problem and solved using a large neighborhood search metaheuristic. The proposed framework is tested on data inspired......Passengers using public transport systems often experience waiting times when transferring between two scheduled services. In this paper we propose a planning approach that seeks to obtain a favourable trade-off between the two contrasting objectives, passenger service and operating cost...

  7. A Mathematical model to predict the US Airlines operation costs and airports charges per route per passenger

    NARCIS (Netherlands)

    Carmona Benitez, R.B.; Lodewijiks, G.

    2010-01-01

    A mathematical model to estimate the average airlines operational costs and airports charges per route is important for airlines companies trying to open new routes and for data generation for other purpose such as transport modeling, simulation modeling, investment analyses for airlines and

  8. 14 CFR 91.517 - Passenger information.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Passenger information. 91.517 Section 91... Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.517 Passenger information. (a) Except as... belts and when smoking is prohibited. (c) If passenger information signs are installed, no passenger or...

  9. Modelling public transport passenger flows in the era of intelligent transport systems COST Action TU1004 (TransITs)

    CERN Document Server

    Noekel, Klaus

    2016-01-01

    This book shows how transit assignment models can be used to describe and predict the patterns of network patronage in public transport systems. It provides a fundamental technical tool that can be employed in the process of designing, implementing and evaluating measures and/or policies to improve the current state of transport systems within given financial, technical and social constraints. The book offers a unique methodological contribution to the field of transit assignment because, moving beyond “traditional” models, it describes more evolved variants that can reproduce: • intermodal networks with high- and low-frequency services; • realistic behavioural hypotheses underpinning route choice; • time dependency in frequency-based models; and • assumptions about the knowledge that users have of network conditions that are consistent with the present and future level of information that intelligent transport systems (ITS) can provide. The book also considers the practical perspective of practit...

  10. Passengers' perception of the safety demonstration on board an aircraft

    Science.gov (United States)

    Ruenruoy, Ratchada

    The cabin safety demonstration on board an aircraft is one of the methods to provide safety information for passengers before aircraft takeoff. However, passengers' enthusiasm toward safety demonstrations is normally low. Therefore, the study of passengers' perception toward safety briefings on board an aircraft is important in increasing the safety awareness for the travelling public on commercial aircraft. A survey was distributed to measure the perceptions of Middle Tennessee State University (MTSU) faculty and staff, Aerospace students, and international students who have traveled in the last year. It was generally found that watching the cabin safety demonstration before aircraft takeoff was believed to be important for passengers. However, the attention to the safety demonstration remained low because the safety briefings were not good enough in terms of clear communication, particularly in the recorded audio demonstration and the live safety demonstration methods of briefing.

  11. Route planning for airport personnel transporting passengers with reduced mobility

    DEFF Research Database (Denmark)

    Reinhardt, Line Blander; Clausen, Tommy; Pisinger, David

    transportation for the passengers with reduced mobility. It is often necessary for a passenger with reduced mobility to use several different modes of transport during their journey through the airport. Synchronization occurs at the locations where transport modes are changed as to not leave passengers...... unattended. A description of the problem together with a mathematical model is presented. The objective is to maximize the quality of service by scheduling as many of the passengers as possible, while ensuring a smooth transport with short waiting times. A simulated annealing based heuristic for solving...... the problem is presented. The algorithm makes use of an abstract representation of a candidate solution which in each step is transformed to an actual schedule by use of a greedy heuristic. Local search is performed on the abstract representation using advanced neighborhoods which modify large parts...

  12. Willingness to Pay of Air Passengers for Carbon-Offset

    Directory of Open Access Journals (Sweden)

    Rong-Chang Jou

    2015-03-01

    Full Text Available An important source of anthropogenic greenhouse gas (GHG emissions is the air transport sector, which accounts for approximately 2% of global GHG emissions. Therefore, reducing GHG emissions from aircrafts has become a major challenge for transportation authorities worldwide. In recent years, much research has focused on tax ideas related to the CO2 emissions produced by air transport, such as the voluntary carbon offset (VCO. This study investigates the willingness of economy class air passengers to pay to compensate for the CO2 emissions produced during their journeys from Taiwan to Hong Kong. Together with the Spike model, a framework known as the contingent valuation (CV method offers a way to investigate how much the air passenger would be willing to pay to offset a journey’s airplane-generated CO2 emissions. The Spike model was applied to address the problem of zero willingness to pay (WTP. The results obtained in this study are consistent with the results found in previous studies and therefore can provide valuable insights into pricing strategies for airlines.

  13. Sizing models and performance analysis of volumetric expansion machines for waste heat recovery through organic Rankine cycles on passenger cars

    OpenAIRE

    Guillaume, Ludovic; Legros, Arnaud; Quoilin, Sylvain; Declaye, Sébastien; Lemort, Vincent

    2013-01-01

    This paper aims at helping designers of waste heat recovery organic (or non-organic) Rankine cycles on internal combustion engines to best select the expander among the piston, scroll and screw machines, and the working fluids among R245fa, ethanol and water. The first part of the paper presents the technical constraints inherent to each machine through a state of the art of the three technologies. The second part of the paper deals with the modeling of such expanders. Finally, in the last pa...

  14. Potential of pedestrian protection systems--a parameter study using finite element models of pedestrian dummy and generic passenger vehicles.

    Science.gov (United States)

    Fredriksson, Rikard; Shin, Jaeho; Untaroiu, Costin D

    2011-08-01

    To study the potential of active, passive, and integrated (combined active and passive) safety systems in reducing pedestrian upper body loading in typical impact configurations. Finite element simulations using models of generic sedan car fronts and the Polar II pedestrian dummy were performed for 3 impact configurations at 2 impact speeds. Chest contact force, head injury criterion (HIC(15)), head angular acceleration, and the cumulative strain damage measure (CSDM(0.25)) were employed as injury parameters. Further, 3 countermeasures were modeled: an active autonomous braking system, a passive deployable countermeasure, and an integrated system combining the active and passive systems. The auto-brake system was modeled by reducing impact speed by 10 km/h (equivalent to ideal full braking over 0.3 s) and introducing a pitch of 1 degree and in-crash deceleration of 1 g. The deployable system consisted of a deployable hood, lifting 100 mm in the rear, and a lower windshield air bag. All 3 countermeasures showed benefit in a majority of impact configurations in terms of injury prevention. The auto-brake system reduced chest force in a majority of the configurations and decreased HIC(15), head angular acceleration, and CSDM in all configurations. Averaging all impact configurations, the auto-brake system showed reductions of injury predictors from 20 percent (chest force) to 82 percent (HIC). The passive deployable countermeasure reduced chest force and HIC(15) in a majority of configurations and head angular acceleration and CSDM in all configurations, although the CSDM decrease in 2 configurations was minimal. On average a reduction from 20 percent (CSDM) to 58 percent (HIC) was recorded in the passive deployable countermeasures. Finally, the integrated system evaluated in this study reduced all injury assessment parameters in all configurations compared to the reference situations. The average reductions achieved by the integrated system ranged from 56 percent

  15. Stress analysis on passenger deck due to modification from passenger ship to vehicle-carrying ship

    Science.gov (United States)

    Zubaydi, A.; Sujiatanti, S. H.; Hariyanto, T. R.

    2018-03-01

    Stress is a basic concept in learning about material mechanism. The main focus that needs to be brought to attention in analyzing stress is strength, which is the structural capacity to carry or distribute loads. The structural capacity not only measured by comparing the maximum stress with the material’s yield strength but also with the permissible stress required by the Indonesian Classification Bureau (BKI), which certainly makes it much safer. This final project analyzes stress in passenger deck that experiences modification due to load changes, from passenger load to vehicle one, carrying: 6-wheels truck with maximum weight of 14 tons, a passenger car with maximum weight of 3.5 tons, and a motorcycle with maximum weight of 0.4 tons. The deck structure is modelled using finite element software. The boundary conditions given to the structural model are fix and simple constraint. The load that works on this deck is the deck load which comes from the vehicles on deck with three vehicles’ arrangement plans. After that, software modelling is conducted for analysis purpose. Analysis result shows a variation of maximum stress that occurs i.e. 135 N/mm2, 133 N/mm2, and 152 N/mm2. Those maximum stresses will not affect the structure of passenger deck’s because the maximum stress that occurs indicates smaller value compared to the Indonesian Classification Bureau’s permissible stress (175 N/mm2) as well as the material’s yield strength (235 N/mm2). Thus, the structural strength of passenger deck is shown to be capable of carrying the weight of vehicles in accordance with the three vehicles’ arrangement plans.

  16. NPS Transit System Passenger Boardings Study: Converting Ticket Sales to Passenger Boardings.

    Science.gov (United States)

    2016-01-01

    This report examines the reporting of passenger boardings (unlinked passenger trips) by NPS transit systems that use a ticket sales conversion methodology. By studying and validating the park units' passenger boarding methodology from converting tick...

  17. Policies and Predictions for a Low-Carbon Transition by 2050 in Passenger Vehicles in East Asia: Based on an Analysis Using the E3ME-FTT Model

    Directory of Open Access Journals (Sweden)

    Aileen Lam

    2018-05-01

    Full Text Available In this paper we apply a model of technological diffusion, Future Technology Transformations in the Transport Sector (FTT: Transport, linked to the E3ME macroeconomic model, to study possible future technological transitions in personal passenger transport in four East Asian countries. We assess how targeted policies could impact on these transitions by defining four scenarios based on policies that aim to reduce emissions from transport. For each country we find that an integrated approach of tax incentives, subsidies, regulations (fuel economy efficiency, kick-start programs and biofuel programs yield the most significant emission reductions because, when combined, they accelerate effectively the diffusion of electric vehicles in the region.

  18. The effect of extended periodic inspection of passenger cars and vans

    DEFF Research Database (Denmark)

    Pilegaard, Ninette; Bernhoft, Inger Marie

    The purpose of this note is to perform a calculation of the costs and benefits of extended period-ic inspection of passenger cars and vans in Denmark, provided that the first inspection of pas-senger cars and vans is performed after four years, then one inspection after two years and thereafter...

  19. Drivers' attitudes toward front or rear child passenger belt use and seat belt reminders at these seating positions.

    Science.gov (United States)

    Kidd, David G; McCartt, Anne T

    2014-01-01

    Passengers, especially those in rear seating positions, use seat belts less frequently than drivers. In-vehicle technology can inform drivers when their passengers are unbuckled and encourage passengers to use belts. The current study collected information about drivers' attitudes toward passenger belt use and belt reminders for front passengers and children in back seats. A national telephone survey of 1218 people 18 and older was conducted, of which 477 respondents were drivers who transport a front seat passenger at least once a week and 254 were drivers who transport an 8- to 15-year-old child in the back seat. Respondents were asked about their attitudes toward belt use by their front passengers or rear child passengers and preferences for different passenger belt reminder features. Ninety percent of drivers who regularly transport front seat passengers said that the passengers always use seat belts. Reported belt use was even higher among 8- to 15-year-old children in the back seat (97%). Among the drivers whose children do not always buckle up, about half said their child unbuckled the belt during the trip. Almost every full-time belt use driver (96%) would encourage front passengers to buckle up if not belted, compared to 57 percent of part-time belt users and nonusers. In contrast, nearly every driver who transports children in the back seat would encourage their belt use, regardless of the driver's belt use habits. Most drivers who transport front passengers wanted passenger belt reminders to encourage passengers to buckle up. Most of these drivers wanted a chime/buzzer or warning light or text display and wanted the reminder to last indefinitely. Most drivers who transport child passengers in the rear seat wanted the vehicle to indicate whether child passengers are unbuckled. A large majority of these drivers wanted notifications via a visual diagram of seating positions and belt use, a chime/buzzer, and a warning light or text display. These drivers

  20. Passenger flow analysis of Beijing urban rail transit network using fractal approach

    Science.gov (United States)

    Li, Xiaohong; Chen, Peiwen; Chen, Feng; Wang, Zijia

    2018-04-01

    To quantify the spatiotemporal distribution of passenger flow and the characteristics of an urban rail transit network, we introduce four radius fractal dimensions and two branch fractal dimensions by combining a fractal approach with passenger flow assignment model. These fractal dimensions can numerically describe the complexity of passenger flow in the urban rail transit network and its change characteristics. Based on it, we establish a fractal quantification method to measure the fractal characteristics of passenger follow in the rail transit network. Finally, we validate the reasonability of our proposed method by using the actual data of Beijing subway network. It has been shown that our proposed method can effectively measure the scale-free range of the urban rail transit network, network development and the fractal characteristics of time-varying passenger flow, which further provides a reference for network planning and analysis of passenger flow.

  1. Logistic system as an essential element of modern organization of railway passenger traffic

    Directory of Open Access Journals (Sweden)

    O.A. Khodoskina

    2012-04-01

    Full Text Available The role and place of passenger transport services in the modern structure of rail transportation is considered. The need for approach to rail passenger transport as a logistics system, which is characterized by a set of parameters corresponding to the concept of logistics system in general and taking into account the peculiarities of railway passenger transportation is determined. The features of formation of such a system, taking into account the generally accepted theoretical approach and the specifics of rail transport are also presented. The concept of logistic system for railway vehicles is given; its overall structure is reviewed. The structure of the particular transport is defined by rail freight and in passenger traffic. Is an example of a mathematical model of the logistics system of rail passenger services on the basis of sets of incoming and outgoing parameters is determined. The structure of technologic process for goods and passenger transportation by rail from the perspective of logistics is characterized.

  2. 77 FR 57186 - Technical Report on Fatality Risk, Mass, and Footprint of Model Year 2000-2007 Passenger Cars and...

    Science.gov (United States)

    2012-09-17

    ...-based CAFE and GHG standards. An important corollary issue is the possible effect of mass reduction that.../staticfiles/rulemaking/pdf/cafe/CAFE_2012-2016_FRIA_04012010.pdf , pp. 464-542); 2003 (68 FR 66153, Docket No...

  3. 76 FR 73008 - Technical Report on Fatality Risk, Mass, and Footprint of Model Year 2000-2007 Passenger Cars and...

    Science.gov (United States)

    2011-11-28

    ... (size) constant is a potential strategy for meeting footprint-based CAFE and GHG standards. An important.../staticfiles/rulemaking/pdf/cafe/CAFE_2012-2016_FRIA_04012010.pdf , pp. 464-542); 2003 (68 FR 66153, Docket No...

  4. Fatal crashes of passenger vehicles before and after adding antilock braking systems.

    Science.gov (United States)

    Farmer, C M; Lund, A K; Trempel, R E; Braver, E R

    1997-11-01

    Fatal crash rates of passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. Vehicles selected for analysis had no other significant design changes between the model years being compared, and the model years with and without antilocks were no more than two years apart. The overall fatal crash rates were similar for the two model years. However, the vehicles with antilocks were significantly more likely to be involved in crashes fatal to their own occupants, particularly single-vehicle crashes. Conversely, antilock vehicles were less likely to be involved in crashes fatal to occupants of other vehicles or nonoccupants (pedestrians, bicyclists). Overall, antilock brakes appear to have had little effect on fatal crash involvement. Further study is needed to better understand why fatality risk has increased for occupants of antilock vehicles.

  5. A Study of Airline Passenger Susceptibility to Atmospheric Turbulence Hazard

    Science.gov (United States)

    Stewart, Eric C.

    2000-01-01

    A simple, generic, simulation math model of a commercial airliner has been developed to study the susceptibility of unrestrained passengers to large, discrete gust encounters. The math model simulates the longitudinal motion to vertical gusts and includes (1) motion of an unrestrained passenger in the rear cabin, (2) fuselage flexibility, (3) the lag in the downwash from the wing to the tail, and (4) unsteady lift effects. Airplane and passenger response contours are calculated for a matrix of gust amplitudes and gust lengths of a simulated mountain rotor. A comparison of the model-predicted responses to data from three accidents indicates that the accelerations in actual accidents are sometimes much larger than the simulated gust encounters.

  6. 19 CFR 4.50 - Passenger lists.

    Science.gov (United States)

    2010-04-01

    ... VESSELS IN FOREIGN AND DOMESTIC TRADES Passengers on Vessels § 4.50 Passenger lists. (a) The master of... passenger and crew lists, as required by § 4.7(a) of this part. If the vessel is arriving from noncontiguous... 19 Customs Duties 1 2010-04-01 2010-04-01 false Passenger lists. 4.50 Section 4.50 Customs Duties...

  7. Energy Use of Passenger Cars

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1998-01-01

    Analysis of the Danish sale and stock of passenger cars, focusing particularly on aspects influencing energy use. The project has tracked the development of vehicle weight, power and fuel economy for both the sale of new cars (from 1980 to 1997)and the stock. In addition, the energy use...

  8. Commercial Passenger Fishing Vessel Fishery

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains the logbook data from U.S.A. Commercial Passenger Fishing Vessels (CPFV) fishing in the U.S.A. EEZ and in waters off of Baja California, from...

  9. CFD Investigation on Long-Haul Passenger Bus

    Science.gov (United States)

    Tan, C. F.; Tee, B. T.; Law, H. C.; Lim, T. L.

    2015-09-01

    Air flow distribution is one of the important factors that will influence the bus passenger comfort during long haul travel. Poor air flow distribution not only cause discomfort to the bus passenger but also influence their travel mode as well. The main purpose of this study is to investigate the air flow performance of the bus air-conditioning system through CFD simulation approach. A 3D CAD model of air ducts was drawn and hence analysed by using CFD software, namely ANSYS Fluent, to determine the airflow rate for every outlets of the air-conditioning system. The simulated result was then validated with experimental data obtained from prototype model of air duct. Based on the findings, new design concepts is proposed with the aim to meet the industry requirement as well as to improve the bus passenger comfort during long haul travel.

  10. Fast Heuristics for Delay Management with Passenger Rerouting

    NARCIS (Netherlands)

    T.A.B. Dollevoet (Twan); D. Huisman (Dennis)

    2011-01-01

    textabstractDelay management models determine which connections should be maintained in case of a delayed feeder train. Recently, delay management models are developed that take into account that passengers will adjust their routes when they miss a connection. However, for large-scale real-world

  11. Diarrhea and related factors among passengers on world cruises departing from Japan.

    Science.gov (United States)

    Yamakawa, Michiyo; Sasai, Megumi; Kasai, Yosuke; Tsuda, Toshihide; Suzuki, Etsuji

    2018-01-25

    Despite growth in the number of cruises worldwide, evidence about diarrhea experienced by cruise ship passengers remains sparse. We investigated rates of diarrhea and related factors among passengers on world cruises departing from Japan. Targeting passengers on five world cruises (n = 4180) from 2012 to 2013 (85-103 travel days), we calculated rates of health seeking behavior for diarrhea by sex, age group, and number of roommates for each cruise. We estimated rate ratios and 95% confidence intervals, using the group aged 20-39 years, women, and 2-4 roommates as referent categories. We found 5.04-6.00 cases per 10,000 person-days in the five cruises, with an elevated number after calling at ports. Older passengers (>60 years) and passengers with fewer roommates had an elevated risk of health seeking behavior for diarrhea, although passengers aged 60 years and without roommates. Older passengers and passengers with fewer roommates may be more likely to seek medical treatment for diarrhea during travel on a world cruise, and should take preventive measures. Copyright © 2018. Published by Elsevier Ltd.

  12. CAD/CAE-technologies application for assessment of passenger safety on railway transport in emergency

    Science.gov (United States)

    Antipin, D. Ya; Shorokhov, S. G.; Bondarenko, O. I.

    2018-03-01

    A possibility of using current software products realizing CAD/CAE-technologies for the assessment of passenger safety in emergency cases on railway transport has been analyzed. On the basis of the developed solid computer model of an anthropometric dummy, the authors carried out an analysis of possible levels of passenger injury during accident collision of a train with an obstacle.

  13. ANALYTICAL ESTIMATION OF MINIMUM AND MAXIMUM TIME EXPENDITURES OF PASSENGERS AT AN URBAN ROUTE STOP

    Directory of Open Access Journals (Sweden)

    Gorbachov, P.

    2013-01-01

    Full Text Available This scientific paper deals with the problem related to the definition of average time spent by passengers while waiting for transport vehicles at urban stops as well as the results of analytical modeling of this value at traffic schedule unknown to the passengers and of two options of the vehicle traffic management on the given route.

  14. Global carbon benefits of material substitution in passenger cars until 2050 and the impact on the steel and aluminum industries.

    Science.gov (United States)

    Modaresi, Roja; Pauliuk, Stefan; Løvik, Amund N; Müller, Daniel B

    2014-09-16

    Light-weighting of passenger cars using high-strength steel or aluminum is a common emissions mitigation strategy. We provide a first estimate of the global impact of light-weighting by material substitution on GHG emissions from passenger cars and the steel and aluminum industries until 2050. We develop a dynamic stock model of the global car fleet and combine it with a dynamic MFA of the associated steel, aluminum, and energy supply industries. We propose four scenarios for substitution of conventional steel with high-strength steel and aluminum at different rates over the period 2010-2050. We show that light-weighting of passenger cars can become a "gigaton solution": Between 2010 and 2050, persistent light-weighting of passenger cars can, under optimal conditions, lead to cumulative GHG emissions savings of 9-18 gigatons CO2-eq compared to development business-as-usual. Annual savings can be up to 1 gigaton per year. After 2030, enhanced material recycling can lead to further reductions: closed-loop metal recycling in the automotive sector may reduce cumulative emissions by another 4-6 gigatons CO2-eq. The effectiveness of emissions mitigation by material substitution significantly depends on how the recycling system evolves. At present, policies focusing on tailpipe emissions and life cycle assessments of individual cars do not consider this important effect.

  15. Determinants of injuries in passenger vessel accidents.

    Science.gov (United States)

    Yip, Tsz Leung; Jin, Di; Talley, Wayne K

    2015-09-01

    This paper investigates determinants of crew and passenger injuries in passenger vessel accidents. Crew and passenger injury equations are estimated for ferry, ocean cruise, and river cruise vessel accidents, utilizing detailed data of individual vessel accidents that were investigated by the U.S. Coast Guard during the time period 2001-2008. The estimation results provide empirical evidence (for the first time in the literature) that crew injuries are determinants of passenger injuries in passenger vessel accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Distribution pattern of public transport passenger in Yogyakarta, Indonesia

    Science.gov (United States)

    Narendra, Alfa; Malkhamah, Siti; Sopha, Bertha Maya

    2018-03-01

    The arrival and departure distribution pattern of Trans Jogja bus passenger is one of the fundamental model for simulation. The purpose of this paper is to build models of passengers flows. This research used passengers data from January to May 2014. There is no policy that change the operation system affecting the nature of this pattern nowadays. The roads, buses, land uses, schedule, and people are relatively still the same. The data then categorized based on the direction, days, and location. Moreover, each category was fitted into some well-known discrete distributions. Those distributions are compared based on its AIC value and BIC. The chosen distribution model has the smallest AIC and BIC value and the negative binomial distribution found has the smallest AIC and BIC value. Probability mass function (PMF) plots of those models were compared to draw generic model from each categorical negative binomial distribution models. The value of accepted generic negative binomial distribution is 0.7064 and 1.4504 of mu. The minimum and maximum passenger vector value of distribution are is 0 and 41.

  17. Urban passenger transport energy saving and emission reduction potential: A case study for Tianjin, China

    International Nuclear Information System (INIS)

    Peng, Binbin; Du, Huibin; Ma, Shoufeng; Fan, Ying; Broadstock, David C.

    2015-01-01

    Highlights: • Potential to reduce urban passenger transport is projected between 2010 and 2040. • Four scenarios reflecting different policy mixes are considered. • The potential for energy conservation and emission reductions are obtained. • Vehicle population regulation is most effective in energy saving and reducing overall GHG. • Emission standards are the most effective measure to reduce pollutant emissions. - Abstract: With rapid growth of the vehicle population, urban passenger transport in China is largely responsible for increases in energy consumption, greenhouse gas (GHG) emissions, and also atmospheric pollutants (NO x , CO, HC, PM). In this paper, we first develop an urban passenger transport energy saving and emission reduction potential evaluation model using the “Long Range Energy Alternatives Planning (LEAP)” tool; and then take Tianjin city as an empirical case to evaluate the reduction potential of final energy consumption, GHG emissions and pollutants emissions of Tianjin’s urban passenger transport sector between 2010 and 2040 under four scenarios, i.e. BAU (business as usual) scenario, PP (the 12th five-year plan policy) scenario, CP (comprehensive policy) scenario and HP (hybrid policy of PP and CP) scenario. The results show that due to the public transport promotion, energy consumption and CO 2 emissions in 2040 can be reduced by 22% and 22.6% in the PP scenario, compared to BAU. The largest reductions in energy consumption, CO 2 and atmospheric pollutants emissions can be achieved under CP scenario, in which vehicle population regulation is the most effective to be implemented. Emissions standard regulation is the most effective measure to reduce atmospheric pollutant emissions in all the scenarios and green energy promotion is especially effective to reduce NO x and PM

  18. Passenger baggage object database (PBOD)

    Science.gov (United States)

    Gittinger, Jaxon M.; Suknot, April N.; Jimenez, Edward S.; Spaulding, Terry W.; Wenrich, Steve A.

    2018-04-01

    Detection of anomalies of interest in x-ray images is an ever-evolving problem that requires the rapid development of automatic detection algorithms. Automatic detection algorithms are developed using machine learning techniques, which would require developers to obtain the x-ray machine that was used to create the images being trained on, and compile all associated metadata for those images by hand. The Passenger Baggage Object Database (PBOD) and data acquisition application were designed and developed for acquiring and persisting 2-D and 3-D x-ray image data and associated metadata. PBOD was specifically created to capture simulated airline passenger "stream of commerce" luggage data, but could be applied to other areas of x-ray imaging to utilize machine-learning methods.

  19. New evidence concerning fatal crashes of passenger vehicles before and after adding antilock braking systems.

    Science.gov (United States)

    Farmer, C M

    2001-05-01

    Fatal crash rates for passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. A prior study, based on fatal crash experience through 1995, reported that vehicle models with antilock brakes were more likely than identical but 1-year-earlier models to be involved in crashes fatal to their own occupants, but were less likely to be involved in crashes fatal to occupants of other vehicles. Overall, there was no significant effect of antilocks on the likelihood of fatal crashes. Similar analyses, based on fatal crash experience during 1996-98, yielded very different results. During 1996-98, vehicles with antilock brakes were again less likely than earlier models to be involved in crashes fatal to occupants of other vehicles, but they were no longer overinvolved in crashes fatal to their own occupants.

  20. Passenger car fuel consumption survey

    Energy Technology Data Exchange (ETDEWEB)

    1984-03-01

    This survey originated from a proposal to monitor the fuel consumption and fuel economy of personal use passenger cars operated in Canada. Its purpose is to establish a data base which would contain information on total distance travelled, total amount of fuel consumed, average distance obtained per unit of fuel, total expenditures on fuel, and seasonal fluctuations in fuel consumption and in distance travelled. Among the needs served by this data base are the monitoring of passenger car fuel economy standards and the estimation of pasenger car fuel requirements in conditions involving fuel shortages. Survey methodology is by telephone interview to trace selected vehicles to the registered owners, at which time a fuel purchase diary is then mailed to the principal driver of the car. The results are tabulated on a quarterly basis and to be released as they become available in bulletins similar to this. Data are presented for each province and the total for Canada is given. During the fourth quarter of 1982, it is estimated that there were 7.3 million personal use passenger cars operated in Canada. These cars were driven 28 billion kilometers and consumed 4.3 billion litres of fuel. Their average litres/100 kilometres and the average fuel consumption was 590 litres. 8 tabs.

  1. Reasons and remedies of inland passenger vessels accidents in Bangladesh

    Science.gov (United States)

    Rashid, Cdr Kaosar; Islam, Muhammad Rabiul

    2017-12-01

    The waterways are very important means of communication in Bangladesh. Every year over 95 million passengers are carried through this route. But, this important mode of transport is ridden with tragic disasters every year, incurring a heavy toll of human lives. In last twenty years (1994 to 2014), around 5,500 people have died and 1,500 gone missing in 658 launch disasters. The inland routes of Barisal, Bhola, Chandpur and Patuakhali and their connected water ways to Dhaka and Chittagong are found to be more accident prone. Lack of Awareness, boundless operation of unfit vessels, overloading of passengers, recruitment of unskilled crews, poor capacity of relevant bodies and low standard maintenance of Inland Water Transport (IWT) channels, poor weather forecasting, profit centered attitude of vessel owners and corruption are initiating these deadly accidents. Despite of a number of initiatives by the government, concerned departments and foreign consultants, the safety aspect of the inland passenger vessels still remains in dark. Combined effort of Department of Shipping, BIWTA, and the attitude of vessels owners as well as passengers are very essential in this respect.

  2. Disruption Management of Rolling Stock in Passenger Railway Transportation

    NARCIS (Netherlands)

    L.K. Nielsen (Lars Kjaer); G. Maróti (Gábor)

    2009-01-01

    textabstractThis paper deals with real-time disruption management of rolling stock in passenger railway transportation. We present a generic framework for modeling disruptions in railway rolling stock schedules. The framework is presented as an online combinatorial decision problem where the

  3. Practice Oriented Algorithmic Disruption Management in Passenger Railways

    NARCIS (Netherlands)

    J.C. Wagenaar (Joris)

    2016-01-01

    markdownabstractHow to deal with a disruption is a question railway companies face on a daily basis. This thesis focusses on the subject how to handle a disruption such that the passenger service is upheld as much as possible. The current mathematical models for disruption management can not yet be

  4. Is passenger vehicle incompatibility still a problem?

    Science.gov (United States)

    Teoh, Eric R; Nolan, Joseph M

    2012-01-01

    Passenger cars often are at a disadvantage when colliding with light trucks (sport utility vehicles [SUVs] and pickups) due to differences in mass, vehicle structural alignment, and stiffness. In 2003, vehicle manufacturers agreed to voluntary measures to improve compatibility, especially in front-to-front and front-to-side crashes, with full adherence to be achieved by September 2009. This study examined whether fatality rates are consistent with the expected benefit of this agreement. Analyses examined 2 death rates for 1- to 4-year-old passenger vehicles during 2000-2001 and 2008-2009 in the United States: occupant deaths per million registered vehicle years in these vehicles and deaths in other cars that collided with these vehicles in 2-vehicle crashes per million registered vehicle years. These rates were computed for each study period and for cars/minivans (referred to as cars), SUVs, and pickups by curb weight (in 500-pound increments). The latter death rate, referred to as the car crash partner death rate, also was computed for front-to-front crashes and front-to-side crashes where the front of the 1- to 4-year-old vehicle struck the side of the partner car. In both study periods, occupant death rates generally decreased for each vehicle type both with increasing curb weight and over time. SUVs experienced the greatest declines compared with cars and pickups. This is due in part to the early fitment of electronic stability control in SUVs, which drastically reduced the incidence of single-vehicle rollover crashes. Pickups had the highest death rates in both study periods. Car crash partner death rates generally declined over time for all vehicle categories but more steeply for SUVs and pickups colliding with cars than for cars colliding with cars. In fact, the car crash partner death rates for SUVs and cars were nearly identical during 2008-2009, suggesting that the voluntary design changes for compatibility have been effective. Car crash partner death

  5. In-use vs. type-approval fuel consumption of current passenger cars in Europe

    International Nuclear Information System (INIS)

    Ntziachristos, L.; Mellios, G.; Tsokolis, D.; Keller, M.; Hausberger, S.; Ligterink, N.E.; Dilara, P.

    2014-01-01

    In-use fuel consumption data of 924 passenger cars (611 petrol, 313 diesel) were collected from various European sources and were evaluated in comparison to their corresponding type-approval values. The analysis indicated that the average in-use fuel consumption was higher than the type-approval one by 11% for petrol cars and 16% for diesel cars. Comparison of this dataset with the Travelcard database in the Netherlands showed that the deviation increased for late model years and in particular for cars with low type-approval values. The deviation was higher than 60% for vehicles registered in 2012 within the 90–100 gCO 2 /km bin. Unrealistic vehicle resistances used in type-approval were identified as one of the prime reasons of the difference. A simplified linear model developed in the study may be used to predict in-use fuel consumption based on data publicly available. The model utilizes the fuel consumption measured in type-approval, the mass, and the engine capacity to provide in-use fuel consumption. This may be either used to correct fuel consumption factors currently utilized by emission models (e.g. COPERT, HBEFA, VERSIT+, and others) or could be used independently to make projections on how fuel consumption may develop on the basis of changing future passenger cars characteristics. - Highlights: • In-use fuel consumption of petrol and diesel passenger cars is 11% and 16% higher than type-approval, respectively. • The relative difference between in-use and type-approval increases for late model and vehicles with low consumption. • Unrealistically low vehicle resistances are identified as a prime reason of low type-approval fuel consumption. • A model developed predicts in-use consumption on the basis of type-approval consumption, vehicle mass, and engine capacity

  6. Disruption Management in Passenger Railway Transportation

    DEFF Research Database (Denmark)

    Jespersen-Groth, Julie; Potthoff, Daniel; Clausen, Jens

    This paper deals with disruption management in passenger railway transportation. In the disruption management process, many actors belonging to different organizations play a role. In this paper we therefore describe the process itself and the roles of the different actors. Furthermore, we discuss...... the three main subproblems in railway disruption management: timetable adjustment, and rolling stock and crew re-scheduling. Next to a general description of these problems, we give an overview of the existing literature and we present some details of the specific situations at DSB S-tog and NS....... These are the railway operators in the suburban area of Copenhagen, Denmark, and on the main railway lines in the Netherlands, respectively. Since not much research has been carried out yet on Operations Research models for disruption management in the railway context, models and techniques that have been developed...

  7. US Advanced Freight and Passenger MAGLEV System

    Science.gov (United States)

    Morena, John J.; Danby, Gordon; Powell, James

    1996-01-01

    Japan and Germany will operate first generation Maglev passenger systems commercially shortly after 2000 A.D. The United States Maglev systems will require sophisticated freight and passenger carrying capability. The U.S. freight market is larger than passenger transport. A proposed advanced freight and passenger Maglev Project in Brevard County Florida is described. Present Maglev systems cost 30 million dollars or more per mile. Described is an advanced third generation Maglev system with technology improvements that will result in a cost of 10 million dollars per mile.

  8. The Chicago to Iowa City intercity passenger rail route : business plan.

    Science.gov (United States)

    2011-03-21

    Business Plan Highlights : -No Iowa General Fund or RIIF appropriations : -State/local partnership : -Funds operation for the first 10 years : -Local cash commitment to passenger rail : -Conservative and practical financial forecasts : -Three compone...

  9. The standard model 30 years of glory

    International Nuclear Information System (INIS)

    Lefrancois, J.

    2001-03-01

    In these 3 lectures the author reviews the achievements of the past 30 years, which saw the birth and the detailed confirmation of the standard model. The first lecture is dedicated to quantum chromodynamics (QCD), deep inelastic scattering, neutrino scattering results, R(e + ,e - ), scaling violation, Drell-Yan reactions and the observation of jets. The second lecture deals with weak interactions and quark and lepton families, the discovery of W and Z bosons, of charm, of the tau lepton and B quarks are detailed. The third lecture focuses on the stunning progress that have been made in accuracy concerning detectors, the typical level of accuracy of previous e + e - experiments was about 5-10%, while the accuracy obtained at LEP/SLC is of order 0.1% to 0.5%. (A.C.)

  10. The standard model 30 years of glory

    Energy Technology Data Exchange (ETDEWEB)

    Lefrancois, J

    2001-03-01

    In these 3 lectures the author reviews the achievements of the past 30 years, which saw the birth and the detailed confirmation of the standard model. The first lecture is dedicated to quantum chromodynamics (QCD), deep inelastic scattering, neutrino scattering results, R(e{sup +},e{sup -}), scaling violation, Drell-Yan reactions and the observation of jets. The second lecture deals with weak interactions and quark and lepton families, the discovery of W and Z bosons, of charm, of the tau lepton and B quarks are detailed. The third lecture focuses on the stunning progress that have been made in accuracy concerning detectors, the typical level of accuracy of previous e{sup +}e{sup -} experiments was about 5-10%, while the accuracy obtained at LEP/SLC is of order 0.1% to 0.5%. (A.C.)

  11. Assessing Rates of Global Warming Emissions from Port- Fuel Injection and Gasoline Direct Injection Engines in Light-Duty Passenger Vehicles

    Science.gov (United States)

    Short, D.; , D., Vi; Durbin, T.; Karavalakis, G.; Asa-Awuku, A. A.

    2013-12-01

    Passenger vehicles are known emitters of climate warming pollutants. CO2 from automobile emissions are an anthropogenic greenhouse gas (GHG) and a large contributor to global warming. Worldwide, CO2 emissions from passenger vehicles are responsible for 11% of the total CO2 emissions inventory. Black Carbon (BC), another common vehicular emission, may be the second largest contributor to global warming (after CO2). Currently, 52% of BC emissions in the U.S are from the transportation sector, with ~10% originating from passenger vehicles. The share of pollutants from passenger gasoline vehicles is becoming larger due to the reduction of BC from diesel vehicles. Currently, the majority of gasoline passenger vehicles in the United States have port- fuel injection (PFI) engines. Gasoline direct injection (GDI) engines have increased fuel economy compared to the PFI engine. GDI vehicles are predicted to dominate the U.S. passenger vehicle market in the coming years. The method of gasoline injection into the combustion chamber is the primary difference between these two technologies, which can significantly impact primary emissions from light-duty vehicles (LDV). Our study will measure LDV climate warming emissions and assess the impact on climate due to the change in U.S vehicle technologies. Vehicles were tested on a light- duty chassis dynamometer for emissions of CO2, methane (CH4), and BC. These emissions were measured on F3ederal and California transient test cycles and at steady-state speeds. Vehicles used a gasoline blend of 10% by volume ethanol (E10). E10 fuel is now found in 95% of gasoline stations in the U.S. Data is presented from one GDI and one PFI vehicle. The 2012 Kia Optima utilizes GDI technology and has a large market share of the total GDI vehicles produced in the U.S. In addition, The 2012 Toyota Camry, equipped with a PFI engine, was the most popular vehicle model sold in the U.S. in 2012. Methane emissions were ~50% lower for the GDI technology

  12. The role of efficiency improvements vs. price effects for modeling passenger car transport demand and energy demand—Lessons from European countries

    International Nuclear Information System (INIS)

    Ajanovic, Amela; Haas, Reinhard

    2012-01-01

    The objective of this paper is to analyze the impact of changes in fuel prices and fuel intensity (i.e. liters of fuel used per 100 kilometers) on overall fuel (gasoline and diesel) consumption and on the demand for vehicle km driven in car passenger transport. This is important for deriving effective policy portfolios consisting of fuel taxes and technical standards such as fuel intensity mandates or specific CO 2 emission limits. To extract these impacts, we apply cointegration analyses to six European countries and their aggregate over the period 1970–2007. We consider the impact of fuel prices, household income and fuel intensity on fuel consumption. Furthermore, we investigate how changes in fuel prices and fuel intensity interact, analyzing the rebound effect due to lower fuel intensity and due to the switch to diesel. Because we find a high rebound effect with 44% more km driven if fuel intensity is improved 100%, the major conclusion of our analysis for policy makers is that technical standards as the only policy instrument will have limited success. Rather we recommend increased fuel taxes along with fuel intensity standards so that the taxes compensate for the rebound due to the standards. - Highlights: ► We find a high rebound effect with 44% more km driven if fuel intensity is improved. ► Technical standards as the only policy instrument will have limited success. ► Fuel taxes accompanied to fuel intensity standards may compensate the rebound effect.

  13. The Effect of Passengers on Teen Driver Behavior

    Science.gov (United States)

    2012-04-01

    A number of studies have shown that passengers substantially increase the risk of crashes for young, novice drivers. This increased risk may result from distractions that young passengers create for drivers. Alternatively, the presence of passengers ...

  14. The prospect for modal shifts in passenger transport worldwide and impacts on energy use and CO2

    International Nuclear Information System (INIS)

    Cuenot, Francois; Fulton, Lew; Staub, John

    2012-01-01

    Travel statistics for most countries are subject to numerous uncertainties. But as presented in this paper, the IEA has developed a sufficient database to estimate passenger travel by mode for major countries and regions around the world, and produce consistent travel and energy use estimates, perhaps the first of their kind. For example, we estimate that in 2005 total global passenger travel using motorised modes was about 40 trillion kilometres, or about 6000 per person. The IEA has also developed a set of travel projections to 2050, including a Baseline and a “Modal Shift” scenario. This paper provides the result of this analysis and estimates the potential impacts on CO 2 from a 25% reduction in car and air travel by 2050 relative to the Baseline in that year. The modelling effort and policy analysis used to support the findings are also described.

  15. Passengers waste production during flights.

    Science.gov (United States)

    Tofalli, Niki; Loizia, Pantelitsa; Zorpas, Antonis A

    2017-12-20

    We assume that during flights the amount of waste that is produced is limited. However, daily, approximately 8000 commercial airplanes fly above Europe's airspace while at the same time, more than 17,000 commercial flights exist in the entire world. Using primary data from airlines, which use the Larnaca's International Airport (LIA) in Cyprus, we have tried to understand why wastes are produced during a typical flight such as food waste, paper, and plastics, as well as how passengers affect the production of those wastes. The compositional analysis took place on 27 flights of 4 different airlines which used LIA as final destination. The evaluation indicated that the passenger's habits and ethics, and the policy of each airline produced different kinds of waste during the flights and especially food waste (FW). Furthermore, it was observed that the only waste management strategy that exists in place in the airport is the collection and the transportation of all those wastes from aircrafts and from the airport in the central unit for further treatment. Hence, this research indicated extremely difficulties to implement any specific waste minimization, or prevention practice or other sorting methods during the flights due to the limited time of the most flights (less than 3 h), the limited available space within the aircrafts, and the strictly safety roles that exist during the flights.

  16. Passenger transport and household activity patterns

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1997-01-01

    Review of Danish passenger transport patterns and analysis of energy consumption, emissions and safety impacts for selected typical households' travelling......Review of Danish passenger transport patterns and analysis of energy consumption, emissions and safety impacts for selected typical households' travelling...

  17. Reform of refined oil product pricing mechanism and energy rebound effect for passenger transportation in China

    International Nuclear Information System (INIS)

    Lin, Boqiang; Liu, Xia

    2013-01-01

    Improving energy efficiency is the primary method adopted by the Chinese government in an effort to achieve energy conservation target in the transport sector. However, the offsetting effect of energy rebound would greatly reduce its real energy-saving potentials. We set up a Linear Approximation of the Almost Ideal Demand System Model (LA-AIDS model) to estimate the rebound effect for passenger transportation in China. Real energy conservation effect of improving energy efficiency can also be obtained in the process. The result shows that the rebound effect is approximately 107.2%. This figure signifies the existence of ‘backfire effect’, indicating that efficiency improvement in practice does not always lead to energy-saving. We conclude that one important factor leading to the rebound effect, is the refined oil pricing mechanism. China's refined oil pricing mechanism has been subjected to criticism in recent years. The results of simulation analysis show that the rebound could be reduced to approximately 90.7% if the refined oil pricing mechanism is reformed. In this regard, we suggest further reforms in the current refined oil pricing mechanism. - Highlights: ► We set up the LA-AIDS model to estimate traffic service demand for urban residents. ► The size of the rebound effect for passenger transportation in China is evaluated. ► The rebound effect for passenger transportation in China is 107.2%. ► Reform of oil pricing could reduced the rebound to 90.7%. ► Reform of oil pricing might be an effective method for mitigating rebound effect

  18. Synchronized dial-a-ride transportation of disabled passengers at airports

    DEFF Research Database (Denmark)

    Reinhardt, Line Blander; Clausen, Tommy; Pisinger, David

    2013-01-01

    The largest airports have a daily average throughput of more than 500 passengers with reduced mobility. The problem of transporting these passengers is in some cases a multi-modal transportation problem with synchronization constraints. A description of the problem together with a mathematical...... model is presented. The objective is to schedule as many of the passengers as possible, while ensuring a smooth transport with short waiting times. A simulated annealing based heuristic for solving the problem is presented. The algorithm makes use of an abstract representation of a candidate solution...

  19. Methods for analysis of passenger trip performance in a complex networked transportation system

    Science.gov (United States)

    Wang, Danyi

    2007-12-01

    The purpose of the Air Transportation System (ATS) is to provide safe and efficient transportation service of passengers and cargo. The on-time performance of a passenger's trip is a critical performance measurement of the Quality of Service (QOS) provided by any Air Transportation System. QOS has been correlated with airline profitability, productivity, customer loyalty and customer satisfaction (Heskett et al. 1994). Btatu and Barnhart have shown that official government and airline on-time performance metrics (i.e. flight-centric measures of air transportation) fail to accurately reflect the passenger experience (Btatu and Barnhart, 2005). Flight-based metrics do not include the trip delays accrued by passengers who were re-booked due to cancelled flights or missed connections. Also, flight-based metrics do not quantify the magnitude of the delay (only the likelihood) and thus fails to provide the consumer with a useful assessment of the impact of a delay. Passenger-centric metrics have not been developed because of the unavailability of airline proprietary data, which is also protected by anti-trust collusion concerns and civil liberty privacy restrictions. Moveover, the growth of the ATS is trending out of the historical range. The objectives of this research were to (1) estimate ATS-wide passenger trip delay using publicly accessible flight data, and (2) investigate passenger trip dynamics out of the range of historical data by building a passenger flow simulation model to predict impact on passenger trip time given anticipated changes in the future. The first objective enables researchers to conduct historical analysis on passenger on-time performance without proprietary itinerary data, and the second objective enables researchers to conduct experiments outside the range of historic data. The estimated passenger trip delay was for 1,030 routes between the 35 busiest airports in the United States in 2006. The major findings of this research are listed as

  20. The Research of China's Civil Aviation Passenger Multi-Channel Service Technology Platform

    Science.gov (United States)

    Zhibing, Xue; Xinming, Wang

    IATA is promoting Simplifying the Business. The traditional passenger services and business process, such as ticketing, airport counters, had a great influence. The airlines have the passenger service and convenience as the next product development requirements. With civil aviation industry and their company's products construction, the authors propose a solution of passenger multi-channel service product platform. The solution is to streamline the business as the breakthrough point, around the convenience of passengers travel services to travelers as the center, using the current mainstream and the latest IT technology to establish passenger service product platform. The solution will promote DCS e-ticketing business development and service channel diversity. In this paper, the research results have been applied in the product platform construction of the authors' company. The practice shows that through traditional business with the latest IT technologies, traditional passenger services into the emerging service model, passenger service product platform has strong advantages and characteristics. Based on the platform, various types of service products is growing rapidly.

  1. [Injuries sustained by bus passengers in the municipality of Odense 1996-1999].

    Science.gov (United States)

    Barsi, T; Faergemann, C; Larsen, L B

    2001-10-22

    Owing to several recent bus-related accidents in Denmark, we wished to investigate injuries sustained by passengers. From our ongoing registration of patients treated in the casualty department at Odense University Hospital, we identified all residents of Odense Municipality who had sustained injuries as bus passengers from 1996 to 1999. Market analysis and demographic information were used to calculate the incidence and risk. Over this four-year period, 327 consecutive injuries had been sustained by 246 bus passengers, 72 men and 174 women, mean ages 44 and 53 years. The incidence rate was 3.3 injured per 10,000 inhabitants per year, with no increasing tendency during the study period. The risk was 2.2 injured per 1,000,000 bus passengers per year, highest in women and increasing with age. Injuries most frequently occurred when the bus stopped (31%), as passengers were boarding or alighting (23%), or during collision with another vehicle (20%). Most commonly injured areas were the lower (30%) and upper (28%) extremities and the head or neck (27%). Contusions and sprains were the most common injuries (59%). The most common fractures were those of the humerus and hip region. Bus passenger injuries are not a growing problem. The incidence increases with age.

  2. Bus-stop Based Real Time Passenger Information System - Case Study Maribor

    Science.gov (United States)

    Čelan, Marko; Klemenčič, Mitja; Mrgole, Anamarija L.; Lep, Marjan

    2017-10-01

    Real time passenger information system is one of the key element of promoting public transport. For the successful implementation of real time passenger information systems, various components should be considered, such as: passenger needs and requirements, stakeholder involvement, technological solution for tracking, data transfer, etc. This article carrying out designing and evaluation of real time passenger information (RTPI) in the city of Maribor. The design phase included development of methodology for selection of appropriate macro and micro location of the real-time panel, development of a real-time passenger algorithm, definition of a technical specification, financial issues and time frame. The evaluation shows that different people have different requirements; therefore, the system should be adaptable to be used by various types of people, according to the age, the purpose of journey, experience of using public transport, etc. The average difference between perceived waiting time for a bus is 35% higher than the actual waiting time and grow with the headway increase. Experiences from Maribor have shown that the reliability of real time passenger system (from technical point of view) must be close to 100%, otherwise the system may have negative impact on passengers and may discourage the use of public transport. Among considered events of arrivals during the test period, 92% of all prediction were accurate. The cost benefit analysis has focused only on potential benefits from reduced perceived users waiting time and foreseen costs of real time information system in Maribor for 10 years’ period. Analysis shows that the optimal number for implementing real time passenger information system at the bus stops in Maribor is set on 83 bus stops (approx. 20 %) with the highest number of passenger. If we consider all entries at the chosen bus stops, the total perceived waiting time on yearly level could be decreased by about 60,000 hours.

  3. Parents as passengers during pediatric transport.

    Science.gov (United States)

    Lewis, M M; Holditch-Davis, D; Brunssen, S

    1997-01-01

    The transport environment presents a unique setting in which the feasibility, advantages, and disadvantages of passengers accompanying a patient must be assessed carefully. The purpose of this study was to describe the current practice of including parents as passengers during pediatric interfacility transport. One-hundred-eighty-eight critical care transport programs in the United States responded to a voluntary mail survey, providing information about current policies, practices, and crew perceptions of the advantages and disadvantages of carrying parents as passengers. Extra seating for passengers was available in 96% of ambulances, 86% of fixed-wing aircraft, and 54% of helicopters used for pediatric transport. Parents traveled as passengers in all types of vehicles; most frequently in ambulances and fixed-wing aircraft. Twenty percent of helicopter programs allowed parent passengers on more than half of their pediatric transports in this vehicle. Advantages of parent passengers included emotional benefit for the parent and child, availability of parents for history and consent, good public relations, and having the parent present if the child dies. Disadvantages included potential parent anxiety, crew distraction, and space limitations. This study reflects the widely diverse policies, practices, and opinions relevant to this topic and confirms a need for further study.

  4. Access improvement to aircraft passengers' hand luggage.

    Science.gov (United States)

    Alberda, W; Kampinga, O; Kassels, R; van Kester, R; Noriega, J; Vink, P

    2015-01-01

    Efficient use of space and passenger comfort in aircraft interiors are major issues. There is not much research available about the flying experience regarding passengers' personal belongings. The objective of this study is to explore concepts within the current aircraft seats which improve the passenger experience related to their personal belongings like wallets, mobile phones and laptops. Through on-site observations, interviews and online questionnaires, data regarding the number of personal belongings taken into the airplane and opinions about access to hand luggage were gathered. These data were used to develop different concepts to optimize the aircraft interior, which were evaluated by passengers. Almost every passenger carries a phone (88%), wallet (94%), travel documents (98%) and keys (76%) with them and they like to have these stored close by. Passengers rate the concept that provides integrated storage in the tray table of the aircraft seat the best. Extra storage possibility in the table-tray seems a promising solution according to the passengers.

  5. Tripartite equilibrium strategy for a carbon tax setting problem in air passenger transport.

    Science.gov (United States)

    Xu, Jiuping; Qiu, Rui; Tao, Zhimiao; Xie, Heping

    2018-03-01

    Carbon emissions in air passenger transport have become increasing serious with the rapidly development of aviation industry. Combined with a tripartite equilibrium strategy, this paper proposes a multi-level multi-objective model for an air passenger transport carbon tax setting problem (CTSP) among an international organization, an airline and passengers with the fuzzy uncertainty. The proposed model is simplified to an equivalent crisp model by a weighted sum procedure and a Karush-Kuhn-Tucker (KKT) transformation method. To solve the equivalent crisp model, a fuzzy logic controlled genetic algorithm with entropy-Bolitzmann selection (FLC-GA with EBS) is designed as an integrated solution method. Then, a numerical example is provided to demonstrate the practicality and efficiency of the optimization method. Results show that the cap tax mechanism is an important part of air passenger trans'port carbon emission mitigation and thus, it should be effectively applied to air passenger transport. These results also indicate that the proposed method can provide efficient ways of mitigating carbon emissions for air passenger transport, and therefore assist decision makers in formulating relevant strategies under multiple scenarios.

  6. Small passenger car transmission test-Chevrolet 200 transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    The small passenger car transmission was tested to supply electric vehicle manufacturers with technical information regarding the performance of commerically available transmissions which would enable them to design a more energy efficient vehicle. With this information the manufacturers could estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. A 1979 Chevrolet Model 200 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. The transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. Torque, speed and efficiency curves map the complete performance characteristics for Chevrolet Model 200 transmission.

  7. Are the Costs of Reducing Greenhouse Gases from Passenger Vehicles Negative?

    OpenAIRE

    Parry, Ian W.H.

    2006-01-01

    Energy models suggest that the cost of reducing carbon emissions from the transportation sector is high relative to other sectors, such as electricity generation. However, this paper shows that taxes to reduce passenger vehicle emissions produce large net benefits, rather than costs, when account is taken of (a) their impact on reducing non-carbon externalities from passenger vehicle use, and (b) interactions with the broader fiscal system. Both of these considerations also strengthen the cas...

  8. Research on Multi-leg Inventory Control Based on Passenger Choice

    OpenAIRE

    Fan, Wei; Su, Qiubo; Ip, Wai Hung

    2014-01-01

    To remedy the lack of mathematical programming and the Expected Marginal Seat Revenue (EMSR) model for multi-leg seat inventory control, this paper proposes a method based on passenger choice. Except for data about which seats passengers decide to opt for, there is no need to obtain distributions of passengers’ demands or other “a priori” information. The proposed method can discover the real factors that affect passengers’ choices, and then estimate the probabilities of seat choices and the ...

  9. Comparison of airline passenger oxygen systems.

    Science.gov (United States)

    Byrne, N J

    1995-08-01

    The principal sources of oxygen for inflight passenger use, scheduled and unscheduled, are examined. Present practices of assessment of the passenger's "fitness to fly" are described. Three partner airlines, British Airways, U.S. Air, and Qantas, catering for more than 8000 oxygen requests annually, are compared. Analysis of customer use suggests that medical oxygen requests are frequently not clinically justified. The growth in demand, for both scheduled and unscheduled use of an expensive resource, supports the need for a "recommended best practice" among carriers. Passengers with respiratory disorders who will most benefit from inflight oxygen are vulnerable either to hypoxia or asthma.

  10. 46 CFR 115.910 - Passenger Ship Safety Certificate.

    Science.gov (United States)

    2010-10-01

    ...) The route specified on the Certificate of Inspection and the SOLAS Passenger Ship Safety Certificate... 46 Shipping 4 2010-10-01 2010-10-01 false Passenger Ship Safety Certificate. 115.910 Section 115... MORE THAN 150 PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND...

  11. Teen Drivers' Perceptions of Their Peer Passengers: Qualitative Study.

    Science.gov (United States)

    Ehsani, Johnathon P; Haynie, Denise L; Luthers, Christina; Perlus, Jessamyn; Gerber, Eli; Ouimet, Marie Claude; Klauer, Sheila G; Simons-Morton, Bruce

    The presence of peer passengers increases teenage drivers' fatal crash risk. Distraction and social influence are the two main factors that have been associated with increased risk. Teen drivers' perceptions of their peer passengers on these factors could inform our understanding of the conditions under which peer passengers increase crash risk or promote safer driving. The purpose of this study was to examine teen drivers' perceptions of their peer passengers on distraction and social influence. A convenience sample of male and female drivers participated in a semi-structured interview that included questions on their perceptions of the effects of peer passengers on driving on distraction and social influence. The analysis of the interviews was guided by a grounded theory approach. Teenage drivers were aware of the risk that peer passengers posed. Some described having passengers in the vehicle as distracting, and recognized that the level of distraction increased with the number of passengers in the vehicle. Drivers that felt responsible for the safety of their peer passengers described strategies they used to control the in-vehicle environment. Drivers described driving with passengers as a performance, and articulated direct and indirect sources of pressure, gender norms, and unspoken expectations of their passengers as influencing their driving behavior. The influence of passengers is situation specific and dependent on whom the passenger(s) may be. Passenger influence may be either protective or harmful, depending on the circumstances. Some passengers exert direct influence, but often their influence appears more indirect and subtle.

  12. 49 CFR 223.15 - Requirements for existing passenger cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Requirements for existing passenger cars. 223.15... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SAFETY GLAZING STANDARDS-LOCOMOTIVES, PASSENGER CARS AND CABOOSES Specific Requirements § 223.15 Requirements for existing passenger cars. (a) Passenger cars built or...

  13. An Airline-Based Multilevel Analysis of Airfare Elasticity for Passenger Demand

    Science.gov (United States)

    Castelli, Lorenzo; Ukovich, Walter; Pesenti, Raffaele

    2003-01-01

    Price elasticity of passenger demand for a specific airline is estimated. The main drivers affecting passenger demand for air transportation are identified. First, an Ordinary Least Squares regression analysis is performed. Then, a multilevel analysis-based methodology to investigate the pattern of variation of price elasticity of demand among the various routes of the airline under study is proposed. The experienced daily passenger demands on each fare-class are grouped for each considered route. 9 routes were studied for the months of February and May in years from 1999 to 2002, and two fare-classes were defined (business and economy). The analysis has revealed that the airfare elasticity of passenger demand significantly varies among the different routes of the airline.

  14. News Teaching Support: New schools network launched Competition: Observatory throws open doors to a select few Festival: Granada to host 10th Ciencia en Acción Centenary: Science Museum celebrates 100 years Award: Queen's birthday honour for science communicator Teacher Training: Training goes where it's needed Conference: Physics gets creative in Christchurch Conference: Conference is packed with ideas Poster Campaign: Bus passengers learn about universe Forthcoming events

    Science.gov (United States)

    2009-09-01

    Teaching Support: New schools network launched Competition: Observatory throws open doors to a select few Festival: Granada to host 10th Ciencia en Acción Centenary: Science Museum celebrates 100 years Award: Queen's birthday honour for science communicator Teacher Training: Training goes where it's needed Conference: Physics gets creative in Christchurch Conference: Conference is packed with ideas Poster Campaign: Bus passengers learn about universe Forthcoming events

  15. 75 FR 26839 - Metrics and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger...

    Science.gov (United States)

    2010-05-12

    ... and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger Rail Investment... performance and service quality of intercity passenger train operations. In compliance with the statute, the... Intercity Passenger Rail Service,'' on the FRA's Web site. Simultaneously, the FRA published a notice in the...

  16. Passenger bus industry weather information application.

    Science.gov (United States)

    2011-03-21

    Adverse weather significantly affects the United States national transportation system, including commercial companies : that rely on highways to support their enterprises. The Passenger Bus (Motorcoach) Industry (PBI) is one such affected : user who...

  17. Salmonella outbreak among railway and airline passengers.

    Science.gov (United States)

    Hatakka, M

    1992-01-01

    A widespread outbreak by Salmonella infantis, infecting a total of 226 people, occurred in Finland at the beginning of August 1986. Of those infected, 107 were railway passengers, 91 were airline passengers and 28 were employed in a food processing establishment. The outbreak among the railway passengers was caused by egg sandwiches, the airline passengers were infected by a meal served on board and the catering employees by the breakfast served in the establishment. The outbreak was caused by food prepared in the establishment's kitchen. The employees' breakfasts had probably been contaminated by an employee who was a symptom-free Salmonella infantis carrier, and a number of the employees subsequently became infected, leading to widespread contamination of the food prepared in the establishment. The spread of the outbreak was further influenced by a heatwave at the time and by shortcomings in the cold storage facilities. The kitchen's hygiene supervision and the quality control of its output were reorganized after the outbreak.

  18. Intercity Passenger Parametric Analysis: Overview: Maglev Analysis

    Science.gov (United States)

    1990-04-02

    This document provides information intended to clarify consideration of some of the technically-based questions which arise in connection with intercity passenger transportation, and to provide insight into the characteristics and potential roles o...

  19. Rail industry job analysis : passenger conductor.

    Science.gov (United States)

    2013-02-01

    This document describes the results of a job analysis that was conducted for the position of railroad Passenger Conductor. Key aspects of the position were identified, including main tasks and knowledge, skills, abilities, and other characteristics (...

  20. Passenger Rail Car Egress -- TRB Workshop

    Science.gov (United States)

    2011-11-01

    The Federal Railroad Administrations (FRA) Office of Railroad Policy and Development is exploring how to enhance regulations that address the safe, timely, and effective emergency evacuation of occupants from passenger rail vehicles in various eme...

  1. Environmental Analysis of Petrol, Diesel and Electric Passenger Cars in a Belgian Urban Setting

    Directory of Open Access Journals (Sweden)

    Nils Hooftman

    2016-01-01

    Full Text Available The combustion of fossil fuels in the transport sector leads to an aggravation of the air quality along city roads and highways. Urban air quality is a serious problem nowadays as the number of vehicles increases on a yearly basis. With stricter Euro emission regulations, vehicle manufacturers are not meeting the imposed limits and are also disregarding the non-exhaust emissions. This paper highlights the relevance of non-exhaust emissions of passenger vehicles, both conventional (diesel and petrol or electric vehicles (EV, on air quality levels in an urban environment in Belgium. An environmental life cycle assessment was carried out based on a real-world emission model for passenger cars and fuel refinery data. A cut-off was applied to the models to highlight what emissions, both from the refinery to the exhaust and electricity production for EV, do actually occur within Belgium’s borders. Results show that not much progress has been made from Euro 4 to 6 for conventional vehicles. Electric vehicles pose the best alternative solution as a more environmentally friendly means of transportation. The analysis results target policy makers with the intention that regulations and policies would be developed in the future and target the characterization of non-exhaust emissions from vehicles. These results indicate that EVs offer a valid solution for addressing the urban air quality issue and that non-exhaust emissions should be addressed in future regulatory steps as they dominate the impact spectrum.

  2. Product modelling: '20 years of stalemate'?

    DEFF Research Database (Denmark)

    Galle, Per

    1998-01-01

    In a recent special issue of Design Studies Michael Ramscar, John Lee, and Helen Pain level a severe criticism against a field of research known as product modeling; a criticism that would be rather damaging if it were based on cogent arguments. I shall argue in this paper that it is not....

  3. One Hundred Years of Bohr Model

    Indian Academy of Sciences (India)

    IAS Admin

    In this article I shall present a brief review of the .... By 1900, the amount of information available about .... resulting value was in quite good agreement with the .... It is fair to say that Bohr's model of the atom is simple, elegant, revolutionary but ...

  4. The seated bus passenger--a review.

    Science.gov (United States)

    Levis, J A

    1978-09-01

    The paper describes the inter-relationship of anthropometry, rig studies and dynamic testing of aspects related to problems of the seated bus passenger. It seeks to draw together sub-sections of a very large study sponsored by the government through the Transport and Road Research Laboratory and undertaken by the Human Factors Group of Leyland Truck and Bus. It is relevant to all those designing passenger carrying transport systems.

  5. Bus accident severity and passenger injury: evidence from Denmark

    DEFF Research Database (Denmark)

    Prato, Carlo Giacomo; Kaplan, Sigal

    2014-01-01

    Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

  6. Level of service at airport passenger terminals

    Directory of Open Access Journals (Sweden)

    Tasić Tamara D.

    2016-01-01

    Full Text Available Airport terminals are designed by level of service standards which are regulated by International Air Transport Association (IATA. Level of service offered to passengers, regarding to the primary processes, is not necessarily equivalent to the level of service perceived by them. The fact that passengers spending longer times in terminals makes the secondary processes more important in passenger experience. Aiming to improving airport attractiveness, and business success, passenger perception is approached by paying close attention. This paper discusses the two aspects of level of service. Concept of level of service used in air traffic industry with purpose of designing and planning of passenger terminal is derived from the Highway Capacity Manual. Subject of the paper regards last changes which have been introduced during 2014. Second part of the paper explains the needs of examining and analyzing passenger perception from the management point of view, and gives overview of methods which are conducted during researches. Similarities and differences are shown among measurements of level of service and perceived level of service, including the importance of these aspects mutual complementing.

  7. Alcohol Fuel in Passenger Car

    Directory of Open Access Journals (Sweden)

    Adam Polcar

    2016-01-01

    Full Text Available The present article studies the effects of combustion of high-percentage mixture of bioethanol and gasoline on the output parameters of a passenger car engine. The car engine has not been structurally modified for the combustion of fuels with higher ethanol content. The mixture used consisted of E85 summer blend and Natural 95 gasoline in a ratio of 50:50. The parameters monitored during the experiment included the air-fuel ratio in exhaust gasses, the power output and torque of the engine and also the specific energy consumption and efficiency of the engine. As is apparent from the results, E85+N95 (50:50 mixture combustion results in lean-burn (λ > 1 due to the presence of oxygen in bioethanol. The lean-burn led to a slight decrease in torque and power output of the engine. However, due to the positive physicochemical properties of bioethanol, the decrease has not been as significant as would normally be expected from the measured air-fuel ratio. These findings are further confirmed by the calculated energy required to produce 1 kWh of energy, and by the higher efficiency of the engine during the combustion of a 50% bioethanol mixture.

  8. Regional disparity of urban passenger transport associated GHG (greenhouse gas) emissions in China: A review

    International Nuclear Information System (INIS)

    Hao, Han; Geng, Yong; Wang, Hewu; Ouyang, Minggao

    2014-01-01

    With China’s urbanization and motorization, greenhouse gas (GHG) emissions from urban passenger transport increased rapidly over recent years. As we estimated, China’s urban passenger transport associated motorized travel, energy consumption and lifecycle GHG emissions reached 2815 billion passenger kilometers (pkm), 77 million tons of oil equivalent (toe) and 335 million ton CO 2 equivalent in 2010, over half of which were located in eastern provinces. Over national level, GHG emissions by private passenger vehicles, business passenger vehicles, taxis, motorcycles, E-bikes, transit buses and urban rails accounted for 57.7%, 13.0%, 7.7%, 8.6%, 1.8%, 10.5% and 0.7% of the total. Significant regional disparity was observed. The province-level per capita GHG emissions ranged from 285 kg/capita in Guizhou to 1273 kg/capita in Beijing, with national average of 486 kg/capita. Depending on province context and local policy orientation, the motorization pathways of China’s several highest motorized provinces are quite diverse. We concluded that motorization rate and transport structure were the substantial factors determining urban passenger transport associated GHG emissions. Considering the great potential of urban passenger transport growth in China, policies guiding the optimization of transport structure should be in place with priority in eastern provinces. - Highlights: • Province-leveled motorized travel, energy consumption and GHG emissions in China were studied. • Significant regional disparities on urban passenger transport were observed. • Region-specific sustainable transport energy policies were discussed

  9. Effect of passenger position on fear of danger experienced during sudden bus stops.

    Science.gov (United States)

    Aoki, Takeo; Uetake, Teruo; Shimoda, Masahiro

    2009-06-01

    The purpose of this study was to identify the effect of bus passengers' positions on their fear of danger when a bus stopped suddenly. A temporary bus running course with one bus stop was set up on the campus of the Tokyo University of Agriculture and Technology (TUAT). The bus ran the course 14 times with the bus stopping twice during the course, once at the bus stop and again just after re-starting from the bus stop. The driver was asked to brake more strongly than usual when stopping. Sixteen students (15 males and 1 female) between the ages of 18 and 21 years participated. In turn, all participants were asked to take 14 different postures in the bus. Participants were also asked to report their level of fear on a rating scale each time the bus stopped. The study showed that (1) passengers' fear of danger at the first sudden stop was typically higher than that at the second stop, (2) standing passengers who held hand straps experienced more fear than those who held fixed safety devices, (3) bus passengers sitting on the centre of the rear seat had a great risk of injury if the bus stopped suddenly, and (4) when passengers faced the window and stood transversely with respect to from the moving direction of the bus and the bus stopped suddenly, passengers' fear of danger was affected by the side of the bus on which they stood as well as which hand they used to grasp a safety device.

  10. Examining Passenger Flow Choke Points at Airports Using Discrete Event Simulation

    Science.gov (United States)

    Brown, Jeremy R.; Madhavan, Poomima

    2011-01-01

    The movement of passengers through an airport quickly, safely, and efficiently is the main function of the various checkpoints (check-in, security. etc) found in airports. Human error combined with other breakdowns in the complex system of the airport can disrupt passenger flow through the airport leading to lengthy waiting times, missing luggage and missed flights. In this paper we present a model of passenger flow through an airport using discrete event simulation that will provide a closer look into the possible reasons for breakdowns and their implications for passenger flow. The simulation is based on data collected at Norfolk International Airport (ORF). The primary goal of this simulation is to present ways to optimize the work force to keep passenger flow smooth even during peak travel times and for emergency preparedness at ORF in case of adverse events. In this simulation we ran three different scenarios: real world, increased check-in stations, and multiple waiting lines. Increased check-in stations increased waiting time and instantaneous utilization. while the multiple waiting lines decreased both the waiting time and instantaneous utilization. This simulation was able to show how different changes affected the passenger flow through the airport.

  11. Airline Passenger Profiling Based on Fuzzy Deep Machine Learning.

    Science.gov (United States)

    Zheng, Yu-Jun; Sheng, Wei-Guo; Sun, Xing-Ming; Chen, Sheng-Yong

    2017-12-01

    Passenger profiling plays a vital part of commercial aviation security, but classical methods become very inefficient in handling the rapidly increasing amounts of electronic records. This paper proposes a deep learning approach to passenger profiling. The center of our approach is a Pythagorean fuzzy deep Boltzmann machine (PFDBM), whose parameters are expressed by Pythagorean fuzzy numbers such that each neuron can learn how a feature affects the production of the correct output from both the positive and negative sides. We propose a hybrid algorithm combining a gradient-based method and an evolutionary algorithm for training the PFDBM. Based on the novel learning model, we develop a deep neural network (DNN) for classifying normal passengers and potential attackers, and further develop an integrated DNN for identifying group attackers whose individual features are insufficient to reveal the abnormality. Experiments on data sets from Air China show that our approach provides much higher learning ability and classification accuracy than existing profilers. It is expected that the fuzzy deep learning approach can be adapted for a variety of complex pattern analysis tasks.

  12. Speed-dependent emission of air pollutants from gasoline-powered passenger cars.

    Science.gov (United States)

    Jung, Sungwoon; Lee, Meehye; Kim, Jongchoon; Lyu, Youngsook; Park, Junhong

    2011-01-01

    In Korea emissions from motor vehicles are a major source of air pollution in metropolitan cities, and in Seoul a large proportion of the vehicle fleet is made up of gasoline-powered passenger cars. The carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NOx) and carbon dioxide (CO2) contained in the exhaust emissions from 76 gasoline-powered passenger cars equipped with three-way catalysts has been assessed by vehicle speed, vehicle mileage and model year. The results show that CO, HC, NOx and CO2 emissions remained almost unchanged at higher speeds but decreased rapidly at lower speeds. While a reduction in CO, HC and NOx emissions was noticeable in vehicles of recent manufacture and lower mileage, CO2 emissions were found to be insensitive to vehicle mileage, but strongly dependent on gross vehicle weight. Lower emissions from more recent gasoline-powered vehicles arose mainly from improvements in three-way catalytic converter technology following strengthened emission regulations. The correlation between CO2 emission and fuel consumption has been investigated with a view to establishing national CO2 emission standards for Korea.

  13. Weighted complex network analysis of the Beijing subway system: Train and passenger flows

    Science.gov (United States)

    Feng, Jia; Li, Xiamiao; Mao, Baohua; Xu, Qi; Bai, Yun

    2017-05-01

    In recent years, complex network theory has become an important approach to the study of the structure and dynamics of traffic networks. However, because traffic data is difficult to collect, previous studies have usually focused on the physical topology of subway systems, whereas few studies have considered the characteristics of traffic flows through the network. Therefore, in this paper, we present a multi-layer model to analyze traffic flow patterns in subway networks, based on trip data and an operation timetable obtained from the Beijing Subway System. We characterize the patterns in terms of the spatiotemporal flow size distributions of both the train flow network and the passenger flow network. In addition, we describe the essential interactions between these two networks based on statistical analyses. The results of this study suggest that layered models of transportation systems can elucidate fundamental differences between the coexisting traffic flows and can also clarify the mechanism that causes these differences.

  14. Time series behaviour of the number of Air Asia passengers: A distributional approach

    Science.gov (United States)

    Asrah, Norhaidah Mohd; Djauhari, Maman Abdurachman

    2013-09-01

    The common practice to time series analysis is by fitting a model and then further analysis is conducted on the residuals. However, if we know the distributional behavior of time series, the analyses in model identification, parameter estimation, and model checking are more straightforward. In this paper, we show that the number of Air Asia passengers can be represented as a geometric Brownian motion process. Therefore, instead of using the standard approach in model fitting, we use an appropriate transformation to come up with a stationary, normally distributed and even independent time series. An example in forecasting the number of Air Asia passengers will be given to illustrate the advantages of the method.

  15. Prospects of introduction of innovative technology overhead passenger traffic on the basis of the passenger ropeways for the modernization of the public transport system of the Bryansk city

    Directory of Open Access Journals (Sweden)

    Lagerev A.V.

    2017-06-01

    Full Text Available In relation to the current situation in the field of public transport in the Bryansk city was shown the main problems in the implementation of innovative technology for the aerial passenger transport on the basis of suspended passenger ropeways (Cable metro. Shows the advantages of the cable metro-based mechatronic technology transportation compared to the traditional suspended passenger ropeways. Was made the technical and economic feasibility analysis of the construction of the cable metro in conditions of a highly urbanized urban environment of large cities, metropolises and urban agglomerations. Presented the statistical data on the development of vehicles in the Bryansk city in the period 2004-2016 years and based on the analysis of these data shows the feasibility of the development of aerial passenger transport as the most high-speed and environmentally friendly mode of transport compared with automobile and electric transport. Considered the possible sources of financing of design and construction works and shows the commercial attractiveness of the project to potential investors in the framework of public-private partnerships. For existing urban development and major transport flows of the Bryansk city was formulated proposals for the location of future transport cable metro lines, order their gaskets, the formation routes of movement of the rolling stock. Made the estimation of labor and financial costs for the implementation of the project of modernization of the public transport system of the city of Bryansk on the basis of the suspended passenger ropeways. The proposed option has the following characteristics: the number of transport lines - 6, total length - 54.8 km, total number of passenger boarding stations - 26, hub passenger stations – 6, the total number of intermediate supports – 100...110 pieces with a span between supports of 400...600 m. the cost of construction of transport lines and the purchase of necessary

  16. Peer Passenger Norms and Pressure: Experimental Effects on Simulated Driving Among Teenage Males.

    Science.gov (United States)

    Bingham, C Raymond; Simons-Morton, Bruce G; Pradhan, Anuj K; Li, Kaigang; Almani, Farideh; Falk, Emily B; Shope, Jean T; Buckley, Lisa; Ouimet, Marie Claude; Albert, Paul S

    2016-08-01

    Serious crashes are more likely when teenage drivers have teenage passengers. One likely source of this increased risk is social influences on driving performance. This driving simulator study experimentally tested the effects of peer influence (i.e., risk-accepting compared to risk-averse peer norms reinforced by pressure) on the driving risk behavior (i.e., risky driving behavior and inattention to hazards) of male teenagers. It was hypothesized that peer presence would result in greater driving risk behavior (i.e., increased driving risk and reduced latent hazard anticipation), and that the effect would be greater when the peer was risk-accepting. Fifty-three 16- and 17-year-old male participants holding a provisional U.S., State of Michigan driver license were randomized to either a risk-accepting or risk-averse condition. Each participant operated a driving simulator while alone and separately with a confederate peer passenger. The simulator world included scenarios designed to elicit variation in driving risk behavior with a teen passenger present in the vehicle. Significant interactions of passenger presence (passenger present vs. alone) by risk condition (risk-accepting vs. risk-averse) were observed for variables measuring: failure to stop at yellow light intersections (Incident Rate Ratio (IRR)=2.16; 95% Confidence Interval [95CI]=1.06, 4.43); higher probability of overtaking (IRR=10.17; 95CI=1.43, 73.35); shorter left turn latency (IRR=0.43; 95CI=0.31,0.60); and, failure to stop at an intersection with an occluded stop sign (IRR=7.90; 95CI=2.06,30.35). In all cases, greater risky driving by participants was more likely with a risk-accepting passenger versus a risk-averse passenger present and a risk-accepting passenger present versus driving alone. Exposure of male teenagers to a risk-accepting confederate peer passenger who applied peer influence increased simulated risky driving behavior compared with exposure to a risk-averse confederate peer

  17. Predicting Passenger Survival Rates on the Titanic

    OpenAIRE

    Prateek Chanda

    2017-01-01

    The sinking of the RMS Titanic is one of the most infamous shipwrecks in history. On April 15, 1912, during her maiden voyage, the Titanic sank after colliding with an iceberg, killing 1502 out of 2224 passengers and crew. This sensational tragedy shocked the international community and led to better safety regulations for ships. One of the reasons that the shipwreck led to such loss of life was that there were not enough lifeboats for the passengers and crew. Although there was some el...

  18. Cosmic radiation exposure to airline flight passenger

    International Nuclear Information System (INIS)

    Momose, Mitsuhiro

    2000-01-01

    At the high altitudes, airline flight passengers can be exposed to some levels of cosmic radiation. The purpose of this study was to quantify this radiation exposure. Cosmic radiation was measured during 5 flights using a personal dosimeter (PDM-102, Aloka). Cosmic radiation equivalent dose rates ranged from 0.7 to 1.43 microsieverts per hour, the average rate was 1.08. For the passenger who travels only occasionally, the cosmic radiation levels are well below occupational limits, and the risks are extremely small. (author)

  19. Cosmic radiation exposure to airline flight passenger

    Energy Technology Data Exchange (ETDEWEB)

    Momose, Mitsuhiro [Shinshu Univ., Matsumoto, Nagano (Japan). School of Medicine

    2000-08-01

    At the high altitudes, airline flight passengers can be exposed to some levels of cosmic radiation. The purpose of this study was to quantify this radiation exposure. Cosmic radiation was measured during 5 flights using a personal dosimeter (PDM-102, Aloka). Cosmic radiation equivalent dose rates ranged from 0.7 to 1.43 microsieverts per hour, the average rate was 1.08. For the passenger who travels only occasionally, the cosmic radiation levels are well below occupational limits, and the risks are extremely small. (author)

  20. The effect of passengers on teen driver behavior : traffic tech.

    Science.gov (United States)

    2012-04-01

    A number of studies have shown that passengers substantially : increase the risk of crashes for young, novice drivers. : This increased risk may result from distractions that young : passengers create for drivers. Alternatively, the presence : of pas...

  1. Passengers' attitudes and behaviour towards motorcycle helmet use ...

    African Journals Online (AJOL)

    Passengers' attitudes and behaviour towards motorcycle helmet use in Ilorin, ... Remember me ... The purpose of this study was to examine the attitudes, knowledge, and behavior of motorcycle passengers to helmet use in Ilorin metropolis, ...

  2. THE PROBLEMS OF PASSENGER TRANSPORTATIONS IN AN INTERNATIONAL COMMUNICATION

    Directory of Open Access Journals (Sweden)

    Yu. S. Barash

    2010-05-01

    Full Text Available The basic aspects of international passenger transportations in Ukraine are represented. The analysis of present situation in these transportations is carried out. Some variants of solving the problems of passenger transportations in an international communication are considered.

  3. Assessing community child passenger safety efforts in three Northwest Tribes.

    Science.gov (United States)

    Smith, M L; Berger, L R

    2002-12-01

    To identify strengths and weaknesses in community based child passenger safety programs by developing a scoring instrument and conducting observations of child restraint use in three Native American communities. The three communities are autonomous Tribal reservations in the Pacific Northwest. Their per capita incomes and rates of unemployment are comparable. In each community, 100 children under 5 years old were observed for car seat use. A six item community assessment tool (100 points maximum) awarded points for such items as the type (primary or secondary) and enforcement of child restraint laws; availability of car seats from distribution programs; extent of educational programs; and access to data on vehicle injuries. For children from birth to 4 years, the car seat use rate ranged from 12%-21%. Rates for infants (71%-80%) far exceeded rates for 1-4 year old children (5%-14%). Community scores ranged from 0 to 31.5 points. There was no correlation between scores and observed car seat use. One reason was the total lack of enforcement of restraint laws. A community assessment tool can highlight weaknesses in child passenger efforts. Linking such a tool with an objective measure of impact can be applied to other injury problems, such as fire safety or domestic violence. The very process of creating and implementing a community assessment can enhance agency collaboration and publicize evidence based "best practices" for injury prevention. Further study is needed to address methodologic issues and to examine crash and medical data in relation to community child passenger safety scores.

  4. AIRLINE ACTIVITY FORECASTING BY REGRESSION MODELS

    Directory of Open Access Journals (Sweden)

    Н. Білак

    2012-04-01

    Full Text Available Proposed linear and nonlinear regression models, which take into account the equation of trend and seasonality indices for the analysis and restore the volume of passenger traffic over the past period of time and its prediction for future years, as well as the algorithm of formation of these models based on statistical analysis over the years. The desired model is the first step for the synthesis of more complex models, which will enable forecasting of passenger (income level airline with the highest accuracy and time urgency.

  5. Passenger choice attributes in choosing a secondary airport: A study of passenger attributes in using Lanseria International Airport

    Directory of Open Access Journals (Sweden)

    Elmarie Kriel

    2016-11-01

    Full Text Available Background: The economic deregulation of the airline industry in South Africa in 1991 was a landmark event and brought about various changes in the air transport market, both locally and internationally. One important after-effect of deregulation was the entry of low-cost carriers (LCCs in 2001, which increased competition in the market and offered passengers the freedom to choose between full-cost carriers and LCCs. It is generally accepted that LCCs have been very successful across the globe, and the main reason for this lies in their simplified lower cost business models. One way of achieving lower costs is for LCCs to operate from secondary or alternative airports. This trend is observed in most regions of the world. In South Africa, and more specifically the Gauteng province, Lanseria International Airport is considered as an alternative airport to OR Tambo International Airport (the main international airport of South Africa and located about 30 km east of the Johannesburg Central Business District [CBD]. Currently, two LCCs operate from this airport with a third LCC airline indicating that it will shortly begin operations from this airport. Objectives: The research presented here reflects on the aspects passengers consider when selecting a secondary airport for their travel needs. It also compares the research findings of passenger attributes when choosing Lanseria Airport as a secondary airport in 2010 to a similar study in 2013 after another LCC commenced operations from the airport. Method: In this exploratory research a face-to-face survey was used as the quantitative data collection method in order to identify the factors that influenced passengers’ airport choice decisions at Lanseria International Airport. Results: From this research it emerged that when airports in a metropolitan area are close to one another, one of the main considerations for passengers is access time when selecting an airport. Even after a second LCC started

  6. Disruption Management in Passenger Transportation - from Air to Tracks

    DEFF Research Database (Denmark)

    Clausen, Jens

    2007-01-01

    of the world has show a dramatic increase as well. Public transportation by e.g. rail has come into focus, and hence also the service level provided by suppliers ad public transportation. These transportation systems are likewise very vulnerable to disruptions. In the airline industry there is a long tradition......Over the last 10 years there has been a tremendous growth in air transportation of passengers. Both airports and airspace are close to saturation with respect to capacity, leading to delays caused by disruptions. At the same time the amount of vehicular trac around and in all larger cities...

  7. From Laboratory to Road. A 2014 update of official and real-world fuel concumption and CO2 values for passenger cars in Europe

    NARCIS (Netherlands)

    Mock, P.; Tietge, U.; Franco, V.; German, J.; Bandivadekar, A.; Ligterink, N.E.; Lambrecht, U.; Kuhlwein, J.; Riemersma, I.

    2014-01-01

    Europe’s passenger-car efficiency regulation has very effectively driven down the official average CO2 emissions and fuel consumption of new passenger cars in the EU. The 2015 target of 130 grams of CO2 per kilometer (g/km) was met two years ahead of schedule and manufacturers are making good

  8. 14 CFR 135.113 - Passenger occupancy of pilot seat.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Passenger occupancy of pilot seat. 135.113... Operations § 135.113 Passenger occupancy of pilot seat. No certificate holder may operate an aircraft type certificated after October 15, 1971, that has a passenger seating configuration, excluding any pilot seat, of...

  9. Rescheduling of Railway Rolling Stock with Dynamic Passenger Flows

    NARCIS (Netherlands)

    L.G. Kroon (Leo); G. Maróti (Gábor); L.K. Nielsen (Lars Kjaer)

    2010-01-01

    textabstractTraditional rolling stock rescheduling applications either treat passengers as static objects whose influence on the system is unchanged in a disrupted situation, or they treat passenger behavior as a given input. In case of disruptions however, we may expect the flow of passengers to

  10. 46 CFR 71.75-5 - Passenger Ship Safety Certificate.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Passenger Ship Safety Certificate. 71.75-5 Section 71.75-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS INSPECTION AND... Passenger Ship Safety Certificate. (a) All vessels on an international voyage are required to have a...

  11. Environmental Performance Evaluation of Ro-Ro Passenger Ferry Transportation

    DEFF Research Database (Denmark)

    Kristensen, Hans Otto Holmegaard; Hagemeister, Constantin

    2012-01-01

    /or emissions per transport unit, is related to the same unit for the different transport forms. For Ro-Ro passenger ferries it can be difficult to find a suitable common transport unit, as they often transport a mix of cargo, such as passengers, passenger cars, trucks, lorries, busses and other rolling...

  12. 49 CFR 541.5 - Requirements for passenger motor vehicles.

    Science.gov (United States)

    2010-10-01

    ... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE THEFT PREVENTION STANDARD § 541.5 Requirements for passenger motor vehicles. (a) Each passenger motor vehicle subject to... 49 Transportation 6 2010-10-01 2010-10-01 false Requirements for passenger motor vehicles. 541.5...

  13. Intercity passenger rail : the congress faces critical decisions about the role of and funding for intercity passenger rail systems

    Science.gov (United States)

    2001-07-25

    With the growth in the nation's highway and aviation systems in the : previous decades, intercity passenger rail service lost its competitive edge. Highways have enabled cars to be competitive with conventional passenger trains (those operating up to...

  14. The Application of Online Check-in in the Process of Passenger Handling in Air Transportation

    Directory of Open Access Journals (Sweden)

    František Adamčík

    2017-11-01

    Full Text Available Passenger handling is one of the most important activities any passenger is obliged to carry out prior to boarding the plane to depart. For the handling process to be safeguarded, it is inevitable to perform the services involved in it fast and efficiently so as to prevent idle times or delays during the procedures potentially resulting in delay of flight. By gradual development of the so-called web-based information technologies, some of the activities involved in the handling process can be delegated to the passengers themselves, thereby achieving a faster course of the passenger handling process. In this contribution the authors are dealing with the status quo of the on-line web-based check-in process in air transportation forecasting the expected course of events in these services in the future. Next, based on analyzing functions and characteristics of similar solutions available in the market, the authors are putting forward their new proposal of their own design of a self-service, on-line system of passenger handling with the aim to simplify and expedite the entire handling process. It is the aim of the authors to develop a competitive design in terms of costs as well as new function and services not offered by the hitherto existing with emphasis on improving efficiency of passenger handling at the airports. The resulting solution thanks to internet based technologies is platform independent and fully applicable to the process of airport passenger handling. To an equal extent, the solutions are being applied by the authors to the educational process, as a training tool for the preparation of the aviation personnel and also as part of simulation models for research in the field of airport processes optimization.

  15. Safety of railroad passenger vehicle dynamics : OMNISIM simulation and test correlations for passenger rail cars

    Science.gov (United States)

    2002-07-01

    The purpose of the work is to validate the safety assessment methodology previously developed for passenger rail vehicle dynamics, which requires the application of simulation tools as well as testing of vehicles under different track scenarios. This...

  16. Integrated Rolling Stock Planning for Suburban Passenger Trains

    DEFF Research Database (Denmark)

    Thorlacius, Per

    used, the result being the loss of optimality. The talk will present a new, integrated rolling stock planning model in which the many requirements are handled all at the same time. Preliminary results from DSB S-tog, the suburban train operator of the City of Copenhagen will also be presented.......A central issue for operators of passenger trains is providing sufficient number of seats while minimising operating costs. This process must be conducted taking a large number of practical, railway oriented requirements into account. Because of this complexity, a stepwise solution was previously...

  17. Serviceability of passenger trains during acquisition projects

    NARCIS (Netherlands)

    Parada Puig, J.E.

    2015-01-01

    Acquiring assets that can be serviced cost effectively is a fundamental goal during large acquisition projects at NS, the largest railway company in the Netherlands. Buying passenger trains and providing their required services requires important strategic decisions involving both the trains and

  18. Biodiesel intercity passenger rail revenue service test.

    Science.gov (United States)

    2013-10-01

    Amtrak, with the support of the Federal Railroad Administration, operated a P-32 passenger locomotive in revenue service for a : period of 12 months, on a blend of 20 percent pure biodiesel and 80 percent #2 ultra-low sulfur diesel (ULSD) fuel. The G...

  19. Disruption Management in Passenger Railway Transportation

    DEFF Research Database (Denmark)

    Groth, Julie Jespersen; Potthoff, Daniel; Clausen, Jens

    2009-01-01

    This paper deals with disruption management in passenger railway transportation. In the disruption management process, many actors belonging to different organizations play a role. In this paper we therefore describe the process itself and the roles of the different actors. Furthermore, we discuss...

  20. Improvement of the directional stability of passenger car trailer couplings with actively controlled steering

    Science.gov (United States)

    Desens, Jens

    The stabilization of pendulum oscillations of passenger car trailer couplings, using active steering, was examined. A linear model of the couplings was presented. Each axle was provided with a controller. The controllers were optimized, with regard to necessary sensors, in order to minimize costs. The rear and the front axles were provided with a control unit in order to compute the potential prevailing in the active steering of several axles. It was shown that the passenger car rear axle was the most suitable for coupling stabilization. The experiment was simulated, using a complex coupling model. The developed controller allowed the passenger car trailer to be driven at a speed higher than 150 km per hour.

  1. Fiscal policy and CO2 emissions of new passenger cars in the EU

    NARCIS (Netherlands)

    Gerlagh, Reyer; Van Den Bijgaart, Inge; Nijland, Hans; Michielsen, Thomas

    To what extent have national fiscal policies contributed to the decarbonisation of newly sold passenger cars? We construct a simple model that generates predictions regarding the effect of fiscal policies on average CO2 emissions of new cars, and then test the model empirically. Our empirical

  2. Experimental Investigation of the Dietary Ecology of the Extinct Passenger Pigeon, Ectopistes migratorius

    Directory of Open Access Journals (Sweden)

    Ben J. Novak

    2018-03-01

    Full Text Available For tens of thousands of years, passenger pigeons (Ectopistes migratorius were a dominant member of eastern North American forest communities, with megaflocks comprising up to several billion individuals. The extinction of passenger pigeons in the early twentieth century undoubtedly influenced associated species and ecosystems as interactions stemming from the pigeons disappeared suddenly. Here, we strive to better understand what was probably one of the most significant of these interactions—that between passenger pigeons and seed bearing trees. Using the band-tailed pigeon (Patagioenas fasciata and the rock dove (Columba livia as physical and ecological proxies, we evaluated passenger pigeon dietary range and potential to disperse seeds. Our findings suggest that the passenger pigeon's dietary range, observed historically to be taxonomically broad, was constrained to certain seed sizes due to bill gape size. In addition, we conclude that the digestive process invariably destroyed consumed seeds but the potential for a nutrition/dispersal mutualism might still have existed via regurgitation and post-mortem release of crop contents. Our results highlight the range of ecological interactions that can be lost with species' extinction and the inherent challenge of understanding the consequences of those interactions.

  3. Vermont travel model 2010-2011 (year 3) report.

    Science.gov (United States)

    2012-10-01

    This report is being prepared under Task 1 of the Maintenance, Operation and Evaluation of the VTrans Statewide Transportation Model contract with the Vermont Agency of Transportation (VTrans) in the 2010-2011 year of the contract. The objectiv...

  4. Strategic Network Modelling for Passenger Transport Pricing

    NARCIS (Netherlands)

    Smits, E.-S.

    2017-01-01

    In the last decade the Netherlands has experienced an economic recession. Now, in 2017, the economy is picking up again. This growth does not only come with advantages because economic growth demands more from the transport system. Congestion is increasing again, the capacity of the train system is

  5. Assessment of NHTSA’s Report “Relationships Between Fatality Risk, Mass, and Footprint in Model Year 2000-2007 Passenger Cars and LTVs”

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division. Energy Analysis Dept.

    2011-09-01

    NHTSA recently completed a logistic regression analysis updating its 2003 and 2010 studies of the relationship between vehicle mass and US fatality risk per vehicle mile traveled (VMT). The new study updates the previous analyses in several ways: updated FARS data from 2002 to 2008 for MY00 to MY07 vehicles are used; induced exposure data from police reported crashes in several additional states are added; a new vehicle category for car-based crossover utility vehicles (CUVs) and minivans is created; crashes with other light-duty vehicles are divided into two groups based on the crash partner vehicle’s weight, and a category for all other fatal crashes is added; and new control variables for new safety technologies and designs, such as electronic stability controls (ESC), side airbags, and methods to meet voluntary agreement to improve light truck compatibility with cars, are included.

  6. Assessment of NHTSA’s Report “Relationships Between Fatality Risk, Mass, and Footprint in Model Year 2000-2007 Passenger Cars and LTVs”

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division. Building Technology and Urban Systems Dept.

    2012-08-01

    NHTSA recently completed a logistic regression analysis updating its 2003 and 2010 studies of the relationship between vehicle mass and US fatality risk per vehicle mile traveled (VMT). The new study updates the previous analyses in several ways: updated FARS data from 2002 to 2008 for MY00 to MY07 vehicles are used; induced exposure data from police reported crashes in several additional states are added; a new vehicle category for car-based crossover utility vehicles (CUVs) and minivans is created; crashes with other light-duty vehicles are divided into two groups based on the crash partner vehicle’s weight, and a category for all other fatal crashes is added; and new control variables for new safety technologies and designs, such as electronic stability controls (ESC), side airbags, and methods to meet voluntary agreement to improve light truck compatibility with cars, are included.

  7. Designing interior space for drivers of passenger vehicle

    Directory of Open Access Journals (Sweden)

    Spasojević-Brkić Vesna K.

    2014-01-01

    Full Text Available The current study is a review of our previous papers with certain improvements, so it proves the hypothesis that passenger vehicles are still not sufficiently adapted to man in terms of ergonomics, especially from the aspect of interior space. In the ergonomic adjustment of passenger vehicles, the limits of anthropomeasures and technical limitations, are the most important. The methodology mainly uses operative investigations, and the 'man-vehicle' system is optimized within existing limitations. Here, we also explain original methodology for modeling that space. The fact that there is a point '0' as the origin point of a coordinate system with x, y and z axes of the man-vehicle system, which can be considered to be more or less fixed, enabled us to determine more accurately the mechanical and mathematical codependence in this system. The paper also proves that the anthropomeasures of length have mechanical and mathematical functions which also determine the width, i.e. all three dimensions and provides the design of the space behind the windscreen glass, the position of the steering wheel and the position of the foot commands with space for feet and knees determined, as well as the total space which the driver occupies. It is proved that the floor-ceiling height of a vehicle is primarily affected by the anthropomeasures of seating height and lower leg, while width is affected by the anthropomeasures of lower and upper leg and only then by shoulder width, so that the interior space for the driver of a passenger vehicle is 1250 mm and the width for knees spread at seat level is 926 mm maximum.

  8. Prices, production, and inventories over the automotive model year

    OpenAIRE

    Adam Copeland; Wendy E. Dunn; George J. Hall

    2005-01-01

    This paper studies the within-model-year pricing and production of new automobiles. Using new monthly data on U.S. transaction prices, we document that for the typical new vehicle, prices typically fall over the model year at a 9.2 percent annual rate. Concurrently, both sales and inventories are hump shaped. To explain these time series, we formulate a market equilibrium model for new automobiles in which inventory and pricing decisions are made simultaneously. On the demand side, we use mic...

  9. The Research on Safety Management Information System of Railway Passenger Based on Risk Management Theory

    Science.gov (United States)

    Zhu, Wenmin; Jia, Yuanhua

    2018-01-01

    Based on the risk management theory and the PDCA cycle model, requirements of the railway passenger transport safety production is analyzed, and the establishment of the security risk assessment team is proposed to manage risk by FTA with Delphi from both qualitative and quantitative aspects. The safety production committee is also established to accomplish performance appraisal, which is for further ensuring the correctness of risk management results, optimizing the safety management business processes and improving risk management capabilities. The basic framework and risk information database of risk management information system of railway passenger transport safety are designed by Ajax, Web Services and SQL technologies. The system realizes functions about risk management, performance appraisal and data management, and provides an efficient and convenient information management platform for railway passenger safety manager.

  10. Adaptive advisory system for economy class passenger with spinal cord injury during air travel

    NARCIS (Netherlands)

    Tan, C.F.; Chen, W.; Verbunt, M.N.C.; Bartneck, C.; Rauterberg, G.W.M.

    2009-01-01

    Today, air travel is popular as a way of transportation for different purpose such as business and tourism. The numbers of air travel passengers are increasing every year. At the same time the flight distance is increased because of better fuel efficiency and technology advancement of airplanes.

  11. Turbulence Hazard Metric Based on Peak Accelerations for Jetliner Passengers

    Science.gov (United States)

    Stewart, Eric C.

    2005-01-01

    Calculations are made of the approximate hazard due to peak normal accelerations of an airplane flying through a simulated vertical wind field associated with a convective frontal system. The calculations are based on a hazard metric developed from a systematic application of a generic math model to 1-cosine discrete gusts of various amplitudes and gust lengths. The math model simulates the three degree-of- freedom longitudinal rigid body motion to vertical gusts and includes (1) fuselage flexibility, (2) the lag in the downwash from the wing to the tail, (3) gradual lift effects, (4) a simplified autopilot, and (5) motion of an unrestrained passenger in the rear cabin. Airplane and passenger response contours are calculated for a matrix of gust amplitudes and gust lengths. The airplane response contours are used to develop an approximate hazard metric of peak normal accelerations as a function of gust amplitude and gust length. The hazard metric is then applied to a two-dimensional simulated vertical wind field of a convective frontal system. The variations of the hazard metric with gust length and airplane heading are demonstrated.

  12. Regional forecasting with global atmospheric models; Third year report

    Energy Technology Data Exchange (ETDEWEB)

    Crowley, T.J.; North, G.R.; Smith, N.R. [Applied Research Corp., College Station, TX (United States)

    1994-05-01

    This report was prepared by the Applied Research Corporation (ARC), College Station, Texas, under subcontract to Pacific Northwest Laboratory (PNL) as part of a global climate studies task. The task supports site characterization work required for the selection of a potential high-level nuclear waste repository and is part of the Performance Assessment Scientific Support (PASS) Program at PNL. The work is under the overall direction of the Office of Civilian Radioactive Waste Management (OCRWM), US Department of Energy Headquarters, Washington, DC. The scope of the report is to present the results of the third year`s work on the atmospheric modeling part of the global climate studies task. The development testing of computer models and initial results are discussed. The appendices contain several studies that provide supporting information and guidance to the modeling work and further details on computer model development. Complete documentation of the models, including user information, will be prepared under separate reports and manuals.

  13. Luttinger model the first 50 years and some new directions

    CERN Document Server

    Mattis, Daniel C

    2014-01-01

    The Luttinger Model is the only model of many-fermion physics with legitimate claims to be both exactly and completely solvable. In several respects it plays the same role in many-body theory as does the 2D Ising model in statistical physics. Interest in the Luttinger model has increased steadily ever since its introduction half a century ago. The present volume starts with reprints of the seminal papers in which it was originally introduced and solved, and continues with several contributions setting out the landscape of the principal advances of the last fifty years and of prominent new dire

  14. Vital Signs - Child Passenger Safety

    Centers for Disease Control (CDC) Podcasts

    This podcast is based on the February 2014 CDC Vital Signs report. Over the past 10 years, more than 9,000 children 12 and under died in motor vehicle crashes, and a third who died in 2011 weren't buckled up. Buckling up is the best way to reduce injuries and save lives.

  15. Driverless operation for public passenger transport systems

    Energy Technology Data Exchange (ETDEWEB)

    Kehl, R. [Siemens AG, Erlangen (Germany). Bereich Verkehrstechnik

    2001-07-01

    The author presents the automation of new and existing lines as a possible solution to the twin problems of the growing need for public transport and the threat of collapse facing many public transport systems in the big conurbations as they wrestle against overloading. It emerges that automatic, driverless operation is a suitable approach to making systems more flexible and more attractive. Automation can increase the capacities of existing systems significantly and thus help them gain more passengers. (orig.)

  16. 75 FR 36300 - Enhancing Airline Passenger Protections

    Science.gov (United States)

    2010-06-25

    ...The Department of Transportation is clarifying its notice of proposed rulemaking (NPRM) published in the Federal Register on June 8, 2010, which, among other issues, solicits comments on options to provide greater access to air travel for persons with peanut allergies. The June 8 document also proposes action to strengthen the rights of air travelers in the event of oversales, flight cancellations and long delays, and to ensure that passengers have accurate and adequate information to make informed decisions when selecting flights.

  17. 75 FR 45562 - Enhancing Airline Passenger Protections

    Science.gov (United States)

    2010-08-03

    ...This action extends the comment period for an NPRM on enhancing airline passenger protections that was published in the Federal Register on June 8, 2010. The Department of Transportation is extending the period for interested persons to submit comments on this rulemaking from August 9, 2010, to September 23, 2010. This extension is a result of requests from a number of airline associations, one airport association, and two airlines to extend the comment period for the proposal.

  18. Costs of mitigating CO2 emissions from passenger aircraft

    Science.gov (United States)

    Schäfer, Andreas W.; Evans, Antony D.; Reynolds, Tom G.; Dray, Lynnette

    2016-04-01

    In response to strong growth in air transportation CO2 emissions, governments and industry began to explore and implement mitigation measures and targets in the early 2000s. However, in the absence of rigorous analyses assessing the costs for mitigating CO2 emissions, these policies could be economically wasteful. Here we identify the cost-effectiveness of CO2 emission reductions from narrow-body aircraft, the workhorse of passenger air transportation. We find that in the US, a combination of fuel burn reduction strategies could reduce the 2012 level of life cycle CO2 emissions per passenger kilometre by around 2% per year to mid-century. These intensity reductions would occur at zero marginal costs for oil prices between US$50-100 per barrel. Even larger reductions are possible, but could impose extra costs and require the adoption of biomass-based synthetic fuels. The extent to which these intensity reductions will translate into absolute emissions reductions will depend on fleet growth.

  19. Present and future energy consumption for passenger transportation in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Kuhne, M.; Wolffram, U.

    1981-01-01

    Passenger transportation in Germany was investigated in order to determine real energy consumption. For typical passengers, energy consumption for overland travel and charter flights was studied. The energy needed for air traffic was compared with that for transportation overland (railway, car, bus), taking into account transportation to the airport or railway station. Transportation makes up about 17% of German primary energy consumption, i.e., road traffic 14%, railway traffic 1.6%, and air traffic 1%. Specific energy consumption (overland travel) of intercity trains, airplanes and cars is in the proportion 1.0 to 3.7 to 4.0 (1980) and is expected to be 1 to 2.4 to 3.1 by the year 2000. For holiday trips, specific energy consumption for bus, train, car and airplane travel is in the proportion 1.0 to 1.4 to 3.6 to 3.4 (1980) and is expected to be 1 to 1.4 to 2.5 to 2.9 by 2000. (ESA)

  20. A Real-Time Holding Decision Rule Accounting for Passenger Travel Cost

    NARCIS (Netherlands)

    Laskaris,; Cats, O.; Jenelius, E; Viti, F

    2016-01-01

    Holding has been extensively investigated as a strategy to mitigate the inherently stochastic nature of public transport operations. Holding focuses on either regulating vehicle headways using a rule-based approach or minimizing passenger travel cost by employing optimization models. This paper

  1. STUDY OF THE EXPERIENCE OF USE OF INTERMODAL TECHNOLOGY IN THE ORGANIZATION OF PASSENGER TRANSPORTATIONS

    Directory of Open Access Journals (Sweden)

    Liudmila Andreevna Paramonova

    2017-05-01

    Full Text Available This article examines the practice of applying intermodal technology and a single transportation document in the organization of passenger transportations, contains a review of the projects on the use of intermodal technology from theoretical point of view, an analysis of the implemented models.

  2. Vital Signs - Child Passenger Safety

    Centers for Disease Control (CDC) Podcasts

    2014-02-04

    This podcast is based on the February 2014 CDC Vital Signs report. Over the past 10 years, more than 9,000 children 12 and under died in motor vehicle crashes, and a third who died in 2011 weren't buckled up. Buckling up is the best way to reduce injuries and save lives.  Created: 2/4/2014 by National Center for Injury Prevention and Control (NCIPC).   Date Released: 2/4/2014.

  3. The risk of airborne influenza transmission in passenger cars.

    Science.gov (United States)

    Knibbs, L D; Morawska, L; Bell, S C

    2012-03-01

    Travel in passenger cars is a ubiquitous aspect of the daily activities of many people. During the 2009 influenza A(H1N1) pandemic a case of probable transmission during car travel was reported in Australia, to which spread via the airborne route may have contributed. However, there are no data to indicate the likely risks of such events, and how they may vary and be mitigated. To address this knowledge gap, we estimated the risk of airborne influenza transmission in two cars (1989 model and 2005 model) by employing ventilation measurements and a variation of the Wells-Riley model. Results suggested that infection risk can be reduced by not recirculating air; however, estimated risk ranged from 59% to 99·9% for a 90-min trip when air was recirculated in the newer vehicle. These results have implications for interrupting in-car transmission of other illnesses spread by the airborne route.

  4. Direct energy rebound effect for road passenger transport in China: A dynamic panel quantile regression approach

    International Nuclear Information System (INIS)

    Zhang, Yue-Jun; Peng, Hua-Rong; Liu, Zhao; Tan, Weiping

    2015-01-01

    The transport sector appears a main energy consumer in China and plays a significant role in energy conservation. Improving energy efficiency proves an effective way to reduce energy consumption in transport sector, whereas its effectiveness may be affected by the rebound effect. This paper proposes a dynamic panel quantile regression model to estimate the direct energy rebound effect for road passenger transport in the whole country, eastern, central and western China, respectively, based on the data of 30 provinces from 2003 to 2012. The empirical results reveal that, first of all, the direct rebound effect does exist for road passenger transport and on the whole country, the short-term and long-term direct rebound effects are 25.53% and 26.56% on average, respectively. Second, the direct rebound effect for road passenger transport in central and eastern China tends to decrease, increase and then decrease again, whereas that in western China decreases and then increases, with the increasing passenger kilometers. Finally, when implementing energy efficiency policy in road passenger transport sector, the effectiveness of energy conservation in western China proves much better than that in central China overall, while the effectiveness in central China is relatively better than that in eastern China. - Highlights: • The direct rebound effect (RE) for road passenger transport in China is estimated. • The direct RE in the whole country, eastern, central, and western China is analyzed. • The short and long-term direct REs are 25.53% and 26.56% within the sample period. • Western China has better energy-saving performance than central and eastern China.

  5. [The psychological profile of pilots of passenger planes: Analysis of temperamental traits, aggression and risk].

    Science.gov (United States)

    Makarowski, Ryszard; Piotrowski, Andrzej

    2017-07-26

    Over the years it has been assumed, that the greater the number of pilot flight hours, the better the development of problem-solving skills among pilots. Research suggests, however, that the problem is more complex than that. Not only one's experience is of importance - temperament, aggression and risk may also affect the decision-making process under stressful conditions. We examined 97 male pilots of passenger planes, who had flew ATRs, Boeings, Airbuses, Embraers, and Saabs. The comparative group was made up of 127 graduates of technical studies (not connected with aviation). In our study, we used the following methods: the PTS (Pavlovian Temperament Survey) Temperament Questionnaire by Strelau, the Aggression Questionnaire by Buss and Perry, and the Stimulating-Instrumental Risk Inventory (SIRI) by Zaleśkiewicz. Following the analyses we could categorize the pilots into 3 distinct groups: group 1 - strong type of nervous system with a tendency to avoid risk; group 2 - strong type of nervous system with a tendency to take risks; group 3 - the relatively weakest type of nervous system with a tendency toward aggressive behavior. Members of each group were analyzed to assess how they function in a task situation, i.e., whilst piloting a passenger plane. The study showed that individuals with high need for stimulation may - consciously or not - seek situations of excessive or unnecessary risks, and this is done in order to reach the right level of stimulation. A constellation of the following variables: temperament, risk, and aggression could be - we argue - useful in psychological examinations, and should be taken into account in training procedures for pilots. Med Pr 2017;68(5):639-651. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

  6. Meeting U.S. passenger vehicle fuel economy standards in 2016 and beyond

    International Nuclear Information System (INIS)

    Cheah, Lynette; Heywood, John

    2011-01-01

    New fuel economy standards require new U.S. passenger vehicles to achieve at least 34.1 miles per gallon (MPG) on average by model year 2016, up from 28.8 MPG today. In this paper, the magnitude, combinations and timings of the changes required in U.S. vehicles that are necessary in order to meet the new standards, as well as a target of doubling the fuel economy within the next two decades are explored. Scenarios of future vehicle characteristics and sales mix indicate that the 2016 mandate is aggressive, requiring significant changes starting from today. New vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel-efficient powertrains, such as smaller turbocharged engines, hybrid-electric drives. Achieving a factor-of-two increase in fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond. A discussion on the feasibility of meeting the new fuel economy mandate is included, considering vehicle production planning realities and challenges in deploying new vehicle technologies into the market. - Research Highlights: → The new 2016 fuel economy standards for passenger vehicles in the U.S. can be met, but are aggressive. → Future vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel efficient powertrains. → The challenge of meeting the fuel economy targets is defined by both the magnitude and the timing of these requirements. → Doubling the fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond.

  7. Price and income elasticities of demand for passenger transport fuels in Spain. Implications for public policies

    International Nuclear Information System (INIS)

    Romero-Jordan, Desiderio; Del Rio, Pablo; Jorge-Garcia, Marta; Burguillo, Mercedes

    2010-01-01

    The significant increase in passenger transport activity (cars) experienced by Spain and its associated increase in energy consumption have several associated negative aspects, including a greater dependence on foreign energy sources and higher GHG emissions. Therefore, reducing the level of transport activity would bring important socioeconomic and environmental benefits. The aim of this paper, which focuses on energy consumption in the passenger transport, is fourfold: (1) to provide a diagnostic of energy consumption in the Spanish passenger transport system and the related problems; (2) to develop a model to calculate price and income elasticities of demand for transport fuel; (3) to apply this model to the Spanish passenger transport sector; (4) to infer policy recommendations derived from the results of the diagnostic and the model. It is claimed that, in view of those low price elasticities and high income elasticities and if a reduction in the scale of transport activity is deemed socially desirable, a combination of instruments is necessary. Fuel taxes play an important role within this combination. Apart from their long-term effects, the low price elasticity of demand for transport fuel would allow the collection of a significant amount of revenues, which could eventually be earmarked to encourage reductions in private transport demand and modal shifts with other instruments. (author)

  8. Price and income elasticities of demand for passenger transport fuels in Spain. Implications for public policies

    Energy Technology Data Exchange (ETDEWEB)

    Romero-Jordan, Desiderio [Universidad Rey Juan Carlos, Madrid (Spain); Del Rio, Pablo [Institute for Public Goods and Policies (IPP), Consejo Superior de Investigaciones Cientificas (CSIC), C/Albasanz, 26-28, Madrid 28037 (Spain); Jorge-Garcia, Marta [Universidad de Leon (Spain); Burguillo, Mercedes [Universidad de Alcala (Spain)

    2010-08-15

    The significant increase in passenger transport activity (cars) experienced by Spain and its associated increase in energy consumption have several associated negative aspects, including a greater dependence on foreign energy sources and higher GHG emissions. Therefore, reducing the level of transport activity would bring important socioeconomic and environmental benefits. The aim of this paper, which focuses on energy consumption in the passenger transport, is fourfold: (1) to provide a diagnostic of energy consumption in the Spanish passenger transport system and the related problems; (2) to develop a model to calculate price and income elasticities of demand for transport fuel; (3) to apply this model to the Spanish passenger transport sector; (4) to infer policy recommendations derived from the results of the diagnostic and the model. It is claimed that, in view of those low price elasticities and high income elasticities and if a reduction in the scale of transport activity is deemed socially desirable, a combination of instruments is necessary. Fuel taxes play an important role within this combination. Apart from their long-term effects, the low price elasticity of demand for transport fuel would allow the collection of a significant amount of revenues, which could eventually be earmarked to encourage reductions in private transport demand and modal shifts with other instruments. (author)

  9. Emergency department visits by pediatric patients sustained as a passenger on a motorcycle.

    Science.gov (United States)

    Tadros, Allison; Owen, Stephanie; Hoffman, Shelley M; Davis, Stephen M; Sharon, Melinda J

    2018-01-02

    Currently only 5 out of the 50 states in the United States have laws restricting the age of passengers permitted to ride on a motorcycle. This study sought to characterize the visits by patients under the age of 16 to U.S. emergency departments (EDs) for injuries sustained as a passenger on a motorcycle. In this retrospective cohort study, data were obtained from the Nationwide Emergency Department Sample (NEDS) for the years 2006 to 2011. Pediatric patients who were passengers on a motorcycle that was involved in a crash were identified using International Classification of Diseases, Ninth Revision (ICD-9) External Cause of Injury codes. We also examined gender, age, disposition, regional differences, common injuries, and charges. Between 2006 and 2011 there were an estimated 9,689 visits to U.S. EDs by patients under the age of 16 who were passengers on a motorcycle involved in a crash. The overall average patient age was 9.4 years, and they were predominately male (54.5%). The majority (85%) of these patients were treated and released. The average charges for discharged patients were $2,116.50 and amounted to roughly $17,500,000 during the 6 years. The average cost for admission was $51,446 per patient and totaled over $54 million. The most common primary injuries included superficial contusions; sprains and strains; upper limb fractures; open wounds of head, neck, and trunk; and intracranial injuries. Although there were only about 9,700 visits to U.S. EDs for motorcycle crashes involving passengers less than 16 years old for 2006 to 2011, the total cost of visits that resulted in either ED discharge or hospital admission amounted to over $71 million.

  10. How Important is the Integration of Public Passenger Transport

    Directory of Open Access Journals (Sweden)

    Mrníková Michaela

    2017-11-01

    Full Text Available The significance of the issue of an effective mode of passenger transport is currently increasing. On the one hand, there is the increasing economic demand of public passenger transport, on the other hand, there is the growing traffic share of individual automobile transport. The objective of the paper is to analyze public passenger transport without mutual integration of individual transport systems resulting in the fact that it is not sufficiently able to compete with individual automobile transport. It is proposed the integration of different modes of public passenger transport as a way to increase the competitiveness of public passenger transport. Aim of this paper is to analyze the individual elements of integration systems and describe why integration of public passenger transport systems is needed.

  11. Fuel economy of new passenger cars in Mexico: Trends from 1988 to 2008 and prospects

    International Nuclear Information System (INIS)

    Sheinbaum-Pardo, Claudia; Chávez-Baeza, Carlos

    2011-01-01

    This paper analyzes trends in fuel economy (kilometers per liter) of new passenger vehicles in Mexico over a period of 20 years from 1988 to 2008. Results show that in this period, fuel economy of the new passenger vehicle fleet, including multipurpose vehicles (a category similar to sport utility vehicles, SUVs), increased by only 6.3%. A simple Laspeyres index analysis was developed to evaluate both the impact of changes in vehicle sales structure by category and the changes in fuel economy. Results show that increased sales of heavier, multipurpose vehicles in place of subcompact and compact vehicles, impacted negatively on the fleet average fuel economy. If the structure of sales had continued in the same proportions across all categories as in 1988, fuel economy would have increased by 11.0%, instead of the actual 6.3%. This result coincides with trends in other countries. The paper also presents different scenarios of passenger car fuel economy for the year 2020, and its implications for gasoline consumption and CO 2 emissions. The results may influence the new passenger vehicle fuel economy standard that is currently under discussion in Mexico.

  12. Optimal planning of the Nordic transmission system with 100% electric vehicle penetration of passenger cars by 2050

    International Nuclear Information System (INIS)

    Graabak, Ingeborg; Wu, Qiuwei; Warland, Leif; Liu, Zhaoxi

    2016-01-01

    This paper presents the optimal planning of the Nordic backbone transmission system with 100% electric vehicle penetration of passenger cars by 2050. Electric vehicles will play an important role in the future energy systems and can reduce the greenhouse gas emission from the transport sector. However, the electric vehicles will increase the electricity consumption and might induce congestions in the transmission systems. In order to deal with the electricity consumption increase from the electric vehicle integration into the power system and maximize the social welfare, the optimal investments of the Nordic transmission system are studied. Case studies were conducted using the market simulation model EMPS (Efi's multi-area power market simulator) and two electric vehicle charging scenarios: a spot price based scenario and a dumb charging scenario. The electric vehicle charging power is assumed to be 3.68 kW with 1 phase 16 A. The complete electrification of the private passenger fleet increases the yearly power demand in the Nordic region with ca 7.5%. The profitable increases in transmission capacities are highest for dumb charging, but are very low for both dumb and spot price based charging compared to a Reference case. - Highlights: • The electric vehicle distribution is done using population and car statistics. • The 100% penetration electric vehicle demand is obtained for Nordic countries. • The optimal investments in the Nordic transmission system with electric vehicles are studied.

  13. Principles of Logistics Applied to Railway Passenger Transport

    Directory of Open Access Journals (Sweden)

    Vojtek Martin

    2017-01-01

    Full Text Available Main challenge of logistics is delivering right assortment of products in exact amount, to exact place, in exact time, ecologically and for exact price. Logistics deals with freight transport but when the word ‘products’ is changed to ‘passengers’, then many principles can be applied to passenger transport. Railway passenger transport is the key part of passenger transport system, so it is necessary to optimize it on logistics philosophy at first.

  14. Analysing passenger arrivals rates and waiting time at bus stops

    OpenAIRE

    Kaparias, I.; Rossetti, C.; Trozzi, V.

    2015-01-01

    The present study investigates the rather under-explored topic of passenger waiting times at public transport facilities. Using data collected from part of London’s bus network by means of physical counts, measurements and observations, and complemented by on-site passenger interviews, the waiting behaviour is analysed for a number of bus stops served by different numbers of lines. The analysis employs a wide range of statistical methods and tools, and concentrates on three aspects: passenger...

  15. ISSUES OF ORGANIZING THE PASSENGER TRANSPORTATION ON US RAILWAYS

    Directory of Open Access Journals (Sweden)

    R. H. Korobiova

    2017-04-01

    Full Text Available Purpose. The paper focuses on a study of the US railway transport organization management during passenger transportation. Methodology. Studies were carried out on the basis of the analysis of literature sources and reporting data on passenger transportation in the USA. Findings. Negative trends in the work of the passenger complex of the Ukrainian railways are the slowdown in the volumes of transportation, the progressive aging of the rolling stock and the overall activity running at a loss for Ukrzaliznytsia. In this regard, the actual task for domestic rail transport is the implementation of industry reforms. Therefore, the paper presented the study of the experience of organizing the passenger transportation on US railways, whose peculiarity is the extremely high degree of competition between modes of transport. As a result of the conducted analysis for working conditions of the US and Ukrainian railways, the general conditions for the functioning of the railways in both countries connected with passenger transportation securing have been established. It was found that general condition for execution of railway passenger transportation for the United States and Ukraine is the subsidization of this activity and combined use of infrastructure for the freight and passengers’ transportations. In this connection, when developing approaches to reforming the passenger economy of Ukraine's railways, it is advisable to use the experience of the United States in assessing the social effectiveness of rail transport, the impact of passenger transportation on the conditions of freight trains handling, and combined use of railway infrastructure by freight and passenger companies. Originality. The author determined the general trends in the development of passenger railway transportation in the US and Ukraine. Practical value. The resulted methods of organizing the operation of the US railway passenger transportation complex can be adapted to solve

  16. Air quality inside the passenger compartment of a bus.

    Science.gov (United States)

    Conceição, E Z; Silva, M C; Viegas, D X

    1997-01-01

    The indoor air quality in the passenger compartment of an intercity bus is studied. A system used for the remotion of the contaminants from the compartment, based on an extraction duct, was projected using a simple, unidimensional flow model with capability to predict the air exchange rate as a function of the vehicle velocity. Some tests using tracer gan methods were performed in a real vehicle with the contaminant remotion system mounted, in order to validate the calculation model and evaluate the performances of the system. A good agreement between the predicted and the experimental results was verified and the obtained air exchange rate was quite reasonable when compared with the former situation, without extraction duct.

  17. Computation of thermal comfort inside a passenger car compartment

    International Nuclear Information System (INIS)

    Mezrhab, A.; Bouzidi, M.

    2006-01-01

    This paper describes a numerical model to study the behaviour of thermal comfort inside the passenger car compartment according to climatic conditions and materials that compose the vehicle. The specifically developed numerical model is based on the nodal method and the finite difference method. Its specificities are: (i) the transient mode, (ii) the taking into account of the combined convection, conduction and radiation heat transfer, (iii) the coupling of two spectral bands (short-wave and long-wave radiation) and two solar fluxes (beam and diffuse). The compartment is subdivided in several solid nodes (materials constituting the compartment) and fluid nodes (volumes of air inside the compartment). The establishment of the heat balance for each node gives the evolution of its temperature. Effects of solar radiation, types of glazing, car colour and radiative properties of materials constituting the compartment are investigated

  18. Analyzing injury severity of bus passengers with different movements.

    Science.gov (United States)

    Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

    2017-07-04

    Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

  19. Study of LH2 fueled subsonic passenger transport aircraft

    Science.gov (United States)

    Brewer, G. D.; Morris, R. E.

    1976-01-01

    The potential of using liquid hydrogen as fuel in subsonic transport aircraft was investigated to explore an expanded matrix of passenger aircraft sizes. Aircraft capable of carrying 130 passengers 2,780 km (1500 n.mi.); 200 passengers 5,560 km (3000 n.mi.); and 400 passengers on a 9,265 km (5000 n.mi.) radius mission, were designed parametrically. Both liquid hydrogen and conventionally fueled versions were generated for each payload/range in order that comparisons could be made. Aircraft in each mission category were compared on the basis of weight, size, cost, energy utilization, and noise.

  20. Carbon emission allowance allocation with a mixed mechanism in air passenger transport.

    Science.gov (United States)

    Qiu, Rui; Xu, Jiuping; Zeng, Ziqiang

    2017-09-15

    Air passenger transport carbon emissions have become a great challenge for both governments and airlines because of rapid developments in the aviation industry in recent decades. In this paper, a mixed mechanism composed of a cap-and-trade mechanism and a carbon tax mechanism is developed to assist governments in allocating carbon emission allowances to airlines operating on the routes. Combined this mixed mechanism with an equilibrium strategy, a bi-level multi-objective model is proposed for an air passenger transport carbon emission allowance allocation problem, in which a government is considered as a leader and the airlines as the followers. An interactive solution approach integrating a genetic algorithm and an interactive evolutionary mechanism is designed to search for satisfactory solutions of the proposed model. A case study is then presented to show its practicality and efficiency in mitigating carbon emissions. Sensitivity analyses under different tradable and taxable levels are also conducted, which can give the government insights as to the tradeoffs between lowering carbon intensity and improving airlines' operations. The computational results demonstrate that the mixed mechanism can assist greatly in carbon emission mitigation for air passenger transport and therefore, it should be established as part of air passenger transport carbon emission policies. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Model Year 2017 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  2. Model Year 2012 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  3. Model Year 2013 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  4. Model Year 2011 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  5. Model Year 2018 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-12-07

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  6. 15 years of food-chain modeling in Romania

    International Nuclear Information System (INIS)

    Gheorghe, R.; Galeriu, D.; Apostoaie, I.; Gheorghe, D.

    2002-01-01

    In the very begin of Chernobyl accident, the high contamination of food, the large variability and the unexpected behavior posed many problems in order to assess the radiological consequences. A simple dynamic food-chain model was built in early May and used for our first assessment on future food contamination and overall impact of Chernobyl in Romania. This quite primitive model show remarkable performance when compared in late 86 and 87 with measurements and our projection of dose was close to a factor two with 10 years later post assessment. After the slowing down of radiological stress we developed a more advanced, process level model of food chain, using not only all literature available but also all local measurements with quality assurance. This model, named LINDOZ, was first internationally applied in the frame of A4 scenario in BIOMOVS 1. and presented in the 1990 Stockholm conference. It was the first time when fallout solubility and foliar absorption were introduced in such a model, explaining very well the dynamics of grass and milk contamination. Upgrades of the model were done concerning deposition and retention and LINDOZ91 was successfully applied in international comparisons VAMP and BIOMOVS 2., including blind tests. Using local expertise and certified data, correlation between probability distribution of deposition and food contamination were used and successfully applied to predict Cs body content distribution in VAMP scenario. Extension to lake-fish was done and tested with excellent results in BIOMOVS 2. In 1994, the model was applied in the first attempt to assess food contamination in Iput region and this old results have been compared recently with those obtained last year by other modelers using updated scenario information. The key points in LINDOZ and its performances in international comparison exercises are presented. In 90'years the German model ECOSYS was spread in Europe and a variant (FDMT) was developed as a food-chain model for

  7. Computable general equilibrium model fiscal year 2013 capability development report

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Brian Keith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rivera, Michael Kelly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boero, Riccardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-17

    This report documents progress made on continued developments of the National Infrastructure Simulation and Analysis Center (NISAC) Computable General Equilibrium Model (NCGEM), developed in fiscal year 2012. In fiscal year 2013, NISAC the treatment of the labor market and tests performed with the model to examine the properties of the solutions computed by the model. To examine these, developers conducted a series of 20 simulations for 20 U.S. States. Each of these simulations compared an economic baseline simulation with an alternative simulation that assumed a 20-percent reduction in overall factor productivity in the manufacturing industries of each State. Differences in the simulation results between the baseline and alternative simulations capture the economic impact of the reduction in factor productivity. While not every State is affected in precisely the same way, the reduction in manufacturing industry productivity negatively affects the manufacturing industries in each State to an extent proportional to the reduction in overall factor productivity. Moreover, overall economic activity decreases when manufacturing sector productivity is reduced. Developers ran two additional simulations: (1) a version of the model for the State of Michigan, with manufacturing divided into two sub-industries (automobile and other vehicle manufacturing as one sub-industry and the rest of manufacturing as the other subindustry); and (2) a version of the model for the United States, divided into 30 industries. NISAC conducted these simulations to illustrate the flexibility of industry definitions in NCGEM and to examine the simulation properties of in more detail.

  8. Defense Transportation Regulation. Part I: Passenger Movement

    Science.gov (United States)

    1998-03-01

    indicates apart action and the "N" in the special handling block identifies the passenger as a no-show. NAME RIC CHANL MSN- NBR /TVL-PD STS...will be retained and annotated with the origin, destination, ticket or token number(s) (when issued), and date issued to traveler. A rubber stamp...J. D. Pierce, TO. The use of a rubber stamp signature of the person authorized to sign GTRs is strictly prohibited. b. Other person(s) (acting TOs

  9. Mode, load, and specific climate impact from passenger trips.

    Science.gov (United States)

    Borken-Kleefeld, Jens; Fuglestvedt, Jan; Berntsen, Terje

    2013-07-16

    The climate impact from a long-distance trip can easily vary by a factor of 10 per passenger depending on mode choice, vehicle efficiency, and occupancy. In this paper we compare the specific climate impact of long-distance car travel with coach, train, or air trips. We account for both, CO2 emissions and short-lived climate forcers. This particularly affects the ranking of aircraft's climate impact relative to other modes. We calculate the specific impact for the Global Warming Potential and the Global Temperature Change Potential, considering time horizons between 20 and 100 years, and compare with results accounting only for CO2 emissions. The car's fuel efficiency and occupancy are central whether the impact from a trip is as high as from air travel or as low as from train travel. These results can be used for carbon-offsetting schemes, mode choice and transportation planning for climate mitigation.

  10. Yearly, seasonal and monthly daily average diffuse sky radiation models

    International Nuclear Information System (INIS)

    Kassem, A.S.; Mujahid, A.M.; Turner, D.W.

    1993-01-01

    A daily average diffuse sky radiation regression model based on daily global radiation was developed utilizing two year data taken near Blytheville, Arkansas (Lat. =35.9 0 N, Long. = 89.9 0 W), U.S.A. The model has a determination coefficient of 0.91 and 0.092 standard error of estimate. The data were also analyzed for a seasonal dependence and four seasonal average daily models were developed for the spring, summer, fall and winter seasons. The coefficient of determination is 0.93, 0.81, 0.94 and 0.93, whereas the standard error of estimate is 0.08, 0.102, 0.042 and 0.075 for spring, summer, fall and winter, respectively. A monthly average daily diffuse sky radiation model was also developed. The coefficient of determination is 0.92 and the standard error of estimate is 0.083. A seasonal monthly average model was also developed which has 0.91 coefficient of determination and 0.085 standard error of estimate. The developed monthly daily average and daily models compare well with a selected number of previously developed models. (author). 11 ref., figs., tabs

  11. Rationalization of Public Road Passenger Transport by Merging Bus Lines on the Example of Zadar County

    Directory of Open Access Journals (Sweden)

    Goran Kos

    2012-07-01

    Full Text Available This study consists of the analysis of public passenger transport in Zadar County, that is, transport on the County and school lines and suggestions of transport rationalization. The rationalization comprises the application of the County and school lines integration, as well as suggestions of other measures which aim to reduce transport costs financed by Zadar County. The objectives to rationalize public passenger transport have been defined, all County transport lines of schoolchildren and other passengers have been analysed as well as actual deficiencies in the city, County and school transport needs. Road transport infrastructure, carriers and transportation vehicles have been analysed. The future transport demand has been reviewed and the prediction of passengers on lines has been provided. Within the next five to ten years no relevant changes will take place, meaning that the balance in transport supply and demand will not be disrupted significantly. This study presents the measures for transport cost reduction and increase in the safety level in the performance of public transport.

  12. An empirical study of direct rebound effect for passenger transport in urban China

    International Nuclear Information System (INIS)

    Wang, H.; Zhou, P.; Zhou, D.Q.

    2012-01-01

    Transport sector accounts for about 8% of total energy consumption in China and this share will likely increase in the visible future. Improving energy efficiency has been considered as a major way for reducing transport energy use, whereas its effectiveness might be affected by the rebound effect. This paper estimates the direct rebound effect for passenger transport in urban China by using the linear approximation of the Almost Ideal Demand System model and simulation analysis. Our empirical results reveal the existence of direct rebound effect for passenger transport in urban China. A majority of the expected reduction in transport energy consumption from efficiency improvement could be offset due to the existence of rebound effect. We have further investigated the relationship between the magnitude of direct rebound effect and households' expenditure. It was found that the direct rebound effect for passenger transport tends to decline with the increase of per capita household consumption expenditure. - Highlights: ► The magnitude of direct rebound effect for urban passenger transport in China is 96%. ► The rebound effect in China could be larger than that in developed countries. ► The rebound effect in China declined with the increase of per capita expenditure.

  13. Clustering method for counting passengers getting in a bus with single camera

    Science.gov (United States)

    Yang, Tao; Zhang, Yanning; Shao, Dapei; Li, Ying

    2010-03-01

    Automatic counting of passengers is very important for both business and security applications. We present a single-camera-based vision system that is able to count passengers in a highly crowded situation at the entrance of a traffic bus. The unique characteristics of the proposed system include, First, a novel feature-point-tracking- and online clustering-based passenger counting framework, which performs much better than those of background-modeling-and foreground-blob-tracking-based methods. Second, a simple and highly accurate clustering algorithm is developed that projects the high-dimensional feature point trajectories into a 2-D feature space by their appearance and disappearance times and counts the number of people through online clustering. Finally, all test video sequences in the experiment are captured from a real traffic bus in Shanghai, China. The results show that the system can process two 320×240 video sequences at a frame rate of 25 fps simultaneously, and can count passengers reliably in various difficult scenarios with complex interaction and occlusion among people. The method achieves high accuracy rates up to 96.5%.

  14. Energy saving and CO2 mitigation through restructuring Jordan's transportation sector: The diesel passenger cars scenario

    International Nuclear Information System (INIS)

    Al-Hinti, I.; Al-Ghandoor, A.; Akash, B.; Abu-Nada, E.

    2007-01-01

    The transportation sector is responsible for 37% of the total final energy consumption in Jordan, with passenger cars taking a share of 57% in this sector. Improvement of the energy efficiency of the transportation sector can help in alleviating socio-economic pressures resulting from the inflating fuel bill and in lowering the relatively high CO 2 emission intensity. Current legislations mandate that all passenger cars operating in Jordan are to be powered with spark ignition engines using gasoline fuel. This paper examines potential benefits that can be achieved through the introduction of diesel cars to the passenger cars market in Jordan. Three scenarios are suggested for implementation and investigated with a forecasting model on the basis of local and global trends over the period 2007-2027. It is demonstrated that introducing diesel passenger cars can slow down the growth of energy consumption in the transportation sector resulting in significant savings in the national fuel bill. It is also shown that this is an effective and feasible option for cutting down CO 2 emissions

  15. General principles of control method of passenger car bodies bending vibration parameters

    Science.gov (United States)

    Skachkov, A. N.; Samoshkin, S. L.; Korshunov, S. D.; Kobishchanov, V. V.; Antipin, D. Ya

    2018-03-01

    Weight reduction of passenger cars is a promising direction of reducing the cost of their production and increasing transportation profitability. One way to reduce the weight of passenger cars is the lightweight metal body design by means of using of high-strength aluminum alloys, low-alloy and stainless steels. However, it has been found that the limit of the lightweight metal body design is not determined by the total mode of deformation, but its flexural rigidity, as the latter influences natural frequencies of body bending vibrations. With the introduction of mandatory certification for compliance with the Customs Union technical regulations, the following index was confirmed: “first natural frequency of body bending vibrations in the vertical plane”. This is due to the fact that vibration, noise and car motion depend on this index. To define the required indexes, the principles of the control method of bending vibration parameters of passenger car bodies are proposed in this paper. This method covers all stages of car design – development of design documentation, manufacturing and testing experimental and pilot models, launching the production. The authors also developed evaluation criteria and the procedure of using the results for introduction of control method of bending vibration parameters of passenger car bodies.

  16. Passenger Rail SOEs as Domestic Institutional Market Actors

    DEFF Research Database (Denmark)

    Tolstrup Christensen, Lene

    2018-01-01

    sectorial challenges. In Sweden, this role has a new public governance form as the monopoly over time is fully dismantled. In Denmark, over time marketization is put on hold due to problems with the SOE as a market actor, but the SOE is nevertheless safeguarded in a new Weberian model as a sector......Purpose: The purpose of this paper is to make an empirical-based conceptualization of the contemporary domestic state-owned enterprises (SOEs) as domestic institutional market actors (IMAs) in the marketization of public service delivery. Design/methodology/approach: The paper is based...... on a qualitative comparative case study of the SOEs in passenger rail in Denmark and Sweden from 1990 to 2015. Findings: The paper shows how marketization results in a layered institutional set-up of public service delivery based on both competition and monopoly where the SOE becomes what we call an IMA bridging...

  17. State and Alternative Fuel Provider Fleets - Fleet Compliance Annual Report: Model Year 2015, Fiscal Year 2016

    Energy Technology Data Exchange (ETDEWEB)

    2016-12-01

    The U.S. Department of Energy (DOE) regulates covered state government and alternative fuel provider fleets, pursuant to the Energy Policy Act of 1992 (EPAct), as amended. Covered fleets may meet their EPAct requirements through one of two compliance methods: Standard Compliance or Alternative Compliance. For model year (MY) 2015, the compliance rate with this program for the more than 3011 reporting fleets was 100%. More than 294 fleets used Standard Compliance and exceeded their aggregate MY 2015 acquisition requirements by 8% through acquisitions alone. The seven covered fleets that used Alternative Compliance exceeded their aggregate MY 2015 petroleum use reduction requirements by 46%.

  18. Fuel conservation and GHG (Greenhouse gas) emissions mitigation scenarios for China’s passenger vehicle fleet

    International Nuclear Information System (INIS)

    Hao, Han; Wang, Hewu; Ouyang, Minggao

    2011-01-01

    Passenger vehicles are the main consumers of gasoline in China. We established a bottom-up model which focuses on the simulation of energy consumptions and greenhouse gas (GHG) emissions growth by China’s passenger vehicle fleet. The fuel conservation and GHG emissions mitigation effects of five measures including constraining vehicle registration, reducing vehicle travel, strengthening fuel consumption rate (FCR) limits, vehicle downsizing and promoting electric vehicle (EV) penetration were evaluated. Based on the combination of these measures, the fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were analyzed. Under reference scenario with no measures implemented, the fuel consumptions and life cycle GHG emissions will reach 520 million tons of oil equivalent (Mtoe) and 2.15 billion tons in 2050, about 8.1 times the level in 2010. However, substantial fuel conservation can be achieved by implementing the measures. By implementing all five measures together, the fuel consumption will reach 138 Mtoe in 2030 and decrease to 126 Mtoe in 2050, which is only 37.1% and 24.3% of the consumption under reference scenario. Similar potential lies in GHG mitigation. The results and scenarios provided references for the Chinese government’s policy-making. -- Highlights: ► We established a bottom-up model to simulate the fuel consumptions and GHG (Greenhouse gas) emissions growth by China’s passenger vehicle fleet. ► Five measures including constraining vehicle registration, reducing vehicle travel, improving fuel efficiency, vehicle downsizing and promoting EV penetration were evaluated. ► The fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were provided as references for policy-making.

  19. Air passenger transport and the greenhouse effect

    International Nuclear Information System (INIS)

    Hubert, M.

    2004-11-01

    The commercial aviation sector accounts for 2.5 % of total worldwide anthropogenic carbon dioxide (CO 2 ) emissions. Water vapour (H 2 O) and NO x emissions, the formation of condensation trails and increased formation of cirrus clouds due to altitude (indirect effects) also accentuate the greenhouse effect. The Intergovernmental Panel on Climate Change (IPCC) estimates that the effects apart from CO 2 emissions are relatively higher for aviation than for other human activities. For one tonne of CO 2 emissions, the radiative forcing of aviation is twice as important as other activities. On this basis, a Paris-New York return trip for one passenger on a charter flight corresponds to a quarter of the total climate impact caused by the annual consumption of a French person. Increased mobility and a rise in international tourism suggest that past trends in the growth of air passenger transport will continue. The improvements in energy efficiency achieved are seemingly not sufficient to prevent a significant increase in the impact of air transport on climate change. (author)

  20. Passenger and Cell Phone Conversations in Simulated Driving

    Science.gov (United States)

    Drews, Frank A.; Pasupathi, Monisha; Strayer, David L.

    2008-01-01

    This study examines how conversing with passengers in a vehicle differs from conversing on a cell phone while driving. We compared how well drivers were able to deal with the demands of driving when conversing on a cell phone, conversing with a passenger, and when driving without any distraction. In the conversation conditions, participants were…

  1. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    2016-09-29

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.  Created: 9/29/2016 by MMWR.   Date Released: 9/29/2016.

  2. 76 FR 77716 - Alternate Passenger Rail Service Pilot Program

    Science.gov (United States)

    2011-12-14

    ...-0108; Notice No. 2] RIN 2130-AC19 Alternate Passenger Rail Service Pilot Program AGENCY: Federal... rule is in response to a statutory mandate that FRA complete a rulemaking proceeding to develop a pilot... enactment of the Passenger Rail Investment and Improvement Act of 2008. The final rule develops this pilot...

  3. 46 CFR 176.910 - Passenger Ship Safety Certificate.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Passenger Ship Safety Certificate. 176.910 Section 176... 100 GROSS TONS) INSPECTION AND CERTIFICATION International Convention for Safety of Life at Sea, 1974, as Amended (SOLAS) § 176.910 Passenger Ship Safety Certificate. (a) A vessel, which carries more than...

  4. Ocean passenger vessels : migrating south for the winter

    Science.gov (United States)

    2010-01-01

    In response to consumer demand, the passenger vessels that operate from seaports along the Atlantic, Gulf, and Pacific coasts alternate between north and south. Passenger vessels that sail out of ports such as New York, Baltimore and Seattle in the s...

  5. 75 FR 78063 - Passenger Weight and Inspected Vessel Stability Requirements

    Science.gov (United States)

    2010-12-14

    ... for determining the maximum passenger capacity of small passenger pontoon vessels either by: Dividing.... 176.110 explicitly calling attention to the OCMI's prerogative to consider a vessel's suitability for... factors to which vessel masters should give special attention in both sections, and a requirement in Sec...

  6. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.

  7. [The use of seatbelts and child seats in drivers and passengers of motor vehicles in four metropolitan areas in Mexico].

    Science.gov (United States)

    Cervantes-Trejo, Arturo; Leenen, Iwin

    2015-01-01

    To estimate the rate of seatbelt and child seat use in drivers and passengers of motor vehicles in four metropolitan areas in Mexico (Guadalajara, León, Monterrey and Mexico City). To evaluate the impact of the Mexican Initiative for Road Safety (IMESEVI) in this respect. Data were collected at the start of IMESEVI (June 2008) and one year after the program's implementation (October 2009) in the four participating metropolitan areas. In particular, the use of seatbelts and child seats was observed in occupants of automobiles, station wagons, and light trucks. The sample included 28,412 (pre) and 52,274 (post) individuals, of which 1,454 (pre) and 1,679 (post) were younger than five years old. The data analysis was based on a hierarchical logistic model. Globally, the probability of using either safety device is 46% (95% CI: 43-49%) at baseline and 52% (95% CI: 48-55%) at the post measurement, with large differences, though, among the four participating metropolitan areas. Factors that significantly affect their use include the individual's position in the vehicle, the type and age of the vehicle, and the individual's sex. Child seat use is very limited. At baseline, about 17% (95% CI: 11-25%) of children below five years old travelled in a special seat, with this number increasing to 26% (95% CI: 19-34%) after the implementation of IMESEVI. Child seat use for children above four years is virtually nonexistent. Continued efforts are required to raise the public awareness of the importance of using safety devices, especially for passengers in the back of the car as well as with respect to the use of adapted seats for small children.

  8. Estimates the Emission of Passenger Cars Based on the First Developed Driving Cycle in Nakhon Ratchasima Municipality, Thailand

    Directory of Open Access Journals (Sweden)

    Muangnak Noppatsorn

    2017-01-01

    Full Text Available This study aims to estimate emissions of passenger cars traveled on the highways in Nakhon Ratchasima Municipality (NRM based on recently developed driving cycles. A mobile phone application (SafeMate was used to record speed-time of passenger car on the highways both weekday and weekend. The results showed that the driving cycles of the passenger cars on highway 224 and 304 were quite different. More traffic congestion on highway 224 impacted the average speeds, ranging from 10 to 34 km/h with longer idling time. The average speeds on highway 304 ranged from 49 to 69 km/h with more cruise time. The combined driving cycles on both highways showed the average speeds of 20-40 km/h depending upon the time of days. The traffic density on weekday was higher than the weekend. Peak-hour weekday showed lower traffic flow than off-peak hour which was the opposite of the weekend. Based on the derived driving cycles, the passenger car traveled on the highways in NRM emitted CO, NOx and HC approximately 90.7-129.8, 25.5-34.5 and 6.9-11.7 tons/year, respectively. The passenger cars were estimated to emit about 13,927.7-20,419.3 tons/year of carbon dioxide on the highways. The highway 2 accounted more of the emissions due to the traffic volume and coverage distance in NRM.

  9. Passenger Perspectives in Railway Timetabling: A Literature Review

    DEFF Research Database (Denmark)

    Jensen, Jens Parbo; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2016-01-01

    When looking at railway planning, a discrepancy exists between planners who focus on the train operations and publish fixed railway schedules, and passengers who look not only at the schedules but also at the entirety of their trip, from access to waiting to on-board travel and egress. Looking...... with fluctuating passenger demand. A key aspect is the robustness of railway timetables. Empirical evidence indicates that passengers give more importance to travel time certainty than travel time reductions, as passengers associate an inherent disutility with travel time uncertainty. This disutility may...... be broadly interpreted as an anxiety cost for the need for having contingency plans in case of disruptions, and may be looked at as the motivator for the need for delay-robust railway timetables. Interestingly, passenger-oriented optimisation studies considering robustness in railway planning typically limit...

  10. Model Year 2015 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  11. Model Year 2009 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-10-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  12. Model Year 2005 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2004-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  13. Model Year 2016 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  14. Model Year 2010 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-10-14

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  15. Model Year 2014 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  16. Scenarios for regional passenger car fleets and their CO2 emissions

    International Nuclear Information System (INIS)

    Meyer, Ina; Kaniovski, Serguei; Scheffran, Jürgen

    2012-01-01

    Passenger car traffic is among the main contributors to anthropogenic greenhouse gas (GHG) emissions, which are responsible for climate change. It is also an important indicator used to forecast these emissions in integrated climate-economic models. This paper develops scenarios for global passenger car stock until 2050. The study adopts a global regionalized approach, encompassing 11 world regions. Car stock projections are obtained using a multi-model approach, which includes a consumer demand model based on utility maximization, a non-linear Gompertz model and a panel estimate of the income elasticity of demand for cars. The main hypothesis underlying these projections is that preferences for purchasing cars are similar across cultures and nations and that the demand for cars is largely determined by disposable income. We apply scenarios for the average traffic volume and fuel efficiency developed in previous work together with the average carbon content of fuels to obtain the CO 2 emissions. - Research highlights: ► This study develops scenarios for global passenger car stock, CO 2 emissions and fuel efficiency until 2050. ► In a global regionalized approach car stock projections are obtained using a multi-model approach. ► Compared are utility maximization, a non-linear Gompertz model and a panel estimate. ► Preferences for purchasing cars are similar across cultures and nations. ► The demand for cars is largely determined by disposable income.

  17. Research on the waiting time of passengers and escalator energy consumption at the railway station

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Wei-wu; Liu, Xiao-yan; Li, Liqing; Shi, Xiangnan; Zhou, Chenn Q. [School of Energy Science and Engineering, Central South University, Changsha 410083 (China)

    2009-12-15

    Based on the Little Formula and the classical queuing model of multi-channel M vertical stroke D vertical stroke n, the relation of the average queue length, the maximum waiting time and the escalator service intensity were identified and the waiting time simulation model was established. With the passenger delivery data at A railway station in China and the probability distribution model of waiting time, a detailed analysis was made on the escalator allocation, power and energy consumption on holidays, ordinary working days and the largest-passengers-volume days; meanwhile, the fixed and variable energy consumption were compared and studied when the waiting time are 5, 10 and 30 s. The result shows that the waiting time settings affect the allocation and the energy consumption of the escalators and the fixed energy consumption takes 70%. (author)

  18. THE FUTURE OF PASSENGER AIR TRANSPORT – VERY LARGE AIRCRAFT AND OUT KEY HUMAN FACTORS AFFECTING THE OPERATION AND SAFETY OF PASSENGER AIR TRANSPORT

    Directory of Open Access Journals (Sweden)

    Petra Skolilova

    2017-12-01

    Full Text Available The article outlines some human factors affecting the operation and safety of passenger air transport given the massive increase in the use of the VLA. Decrease of the impact of the CO2 world emissions is one of the key goals for the new aircraft design. The main wave is going to reduce the burned fuel. Therefore, the eco-efficiency engines combined with reasonable economic operation of the aircraft are very important from an aviation perspective. The prediction for the year 2030 says that about 90% of people, which will use long-haul flights to fly between big cities. So, the A380 was designed exactly for this time period, with a focus on the right capacity, right operating cost and right fuel burn per seat. There is no aircraft today with better fuel burn combined with eco-efficiency per seat, than the A380. The very large aircrafts (VLAs are the future of the commercial passenger aviation. Operating cost versus safety or CO2 emissions versus increasing automation inside the new generation aircraft. Almost 80% of the world aircraft accidents are caused by human error based on wrong action, reaction or final decision of pilots, the catastrophic failures of aircraft systems, or air traffic control errors are not so frequent. So, we are at the beginning of a new age in passenger aviation and the role of the human factor is more important than ever.

  19. Building Airline Passenger Loyalty Through an Understanding of Customer Value: A Relationship Segmentation of Airline Passengers

    OpenAIRE

    Leick, Ryan

    2007-01-01

    This thesis explores means of restoring profitability to the airline industry by cultivating intrinsically motivated brand loyalty between passengers and airlines in today’s fragile environment. The air transport industry is caught up in traditional transaction-based strategies. Airlines rely on archaic frequent flyer programs (FFPs) to maintain loyalty which deter customers from choosing alternative airlines by increasing the cost associated with switching. In contrast, oth...

  20. Modelos basados en grafos: una aplicación al estudio del gasto de cruceristas en Uruguay || Graph-Based Models: An Application to the Study of Cruise Passengers' Expenditure in Uruguay

    Directory of Open Access Journals (Sweden)

    Brida, Juan Gabriel

    2017-12-01

    Full Text Available Este trabajo introduce el uso de grafos en el análisis de los determinantes del gasto de los turistas y lo aplica al estudio del comportamiento de los pasajeros de cruceros que desembarcan en Uruguay en los puertos de Montevideo y Punta del Este. Este enfoque ofrece un abordaje alternativo a los usualmente empleados para analizar los determinantes del gasto turístico al introducir una representación gráfica que permite sintetizar y visualizar las relaciones entre el conjunto de variables que caracterizan a los turistas o grupos de turistas y los determinantes de su nivel de gasto. En particular, la metodología permite representar las relaciones de dependencia entre variables (entre nodos adyacentes e independencias condicionadas (entre nodos no adyacentes. Para su aplicación, se consideran datos individuales de las encuestas realizadas a cruceristas correspondientes a la temporada de cruceros comprendida entre noviembre de 2014 y abril de 2015, ambos incluidos, en Uruguay. Se estudia la existencia de dependencias de las variables relativas a registrar el gasto de los cruceristas con otras variables (sociodemográficas, de contexto, etc.. El estudio muestra que las variables que mejor explican el comportamiento de los visitantes son las vinculadas al puerto de desembarco y al gasto. Asimismo, los resultados muestran que las variables socioeconómicas no están vinculadas al gasto en forma directa. || This paper introduces the use of graphs in the analysis of the determinants of tourists' expenditure, providing an alternative approach to the methods usually employed. Graph-based analysis is applied to study the behavior of cruise passengers arriving at the ports of Montevideo and Punta del Este in Uruguay. The graphical representation allows to synthesize and visualize the relationships between the set of variables that characterize tourists or tourist groups and the determinants of their level of spending. The graph-based methodology is

  1. Emergency medicine and the airline passenger

    Science.gov (United States)

    Mohler, S. R.; Nicogossian, A.; Margulies, R. A.

    1980-01-01

    Problems related to immediate medical care in case of in-flight emergencies are discussed with reference to such critical types of medical emergencies as obstructed airway, cardiac dysfunction, trauma, hemorrhage, hypoxia, and pain. It is shown that training flight attendants to deal with in-flight medical emergencies and to use first-aid support equipment and essential and useful drugs may later help with stabilization of a victim and allow continuing the flight to the scheduled destination without the need for a diverted landing. Among the steps suggested in order to upgrade inflight welfare and safety of passengers are the development of an advisory circular by the FAA covering standardized training for flight attendants, regulatory action requiring upgrading of the present rudimentary first-aid kit, and the enactment of Good Samaritan legislation by the U.S. Government.

  2. Sound design for diesel passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Belluscio, Michele; Ruotolo, Romualdo [GM Powertrain Europe, Torino (Italy); Schoenherr, Christian; Schuster, Guenter [GM Europe, Ruesselsheim (Germany); Eisele, Georg; Genender, Peter; Wolff, Klaus; Van Keymeulen, Johan [FEV Motorentechnik GmbH, Aachen (Germany)

    2008-07-01

    With the growing market contribution of diesel passenger cars in Europe, it becomes more important to create a brand and market segment specific vehicle sound. Beside the usually considered pleasantness related topics like diesel knocking and high noise excitation, it is important to fulfil also the requirements regarding a dynamic vehicle impression. This impression is mainly influenced by the load dependency of the engine induced noise, which is reduced for diesel engines due to the missing throttle valve and the damping effect of the turbocharger and the diesel particulate filter. By means of a detailed noise transfer path analysis the contribution with dynamic potential can be identified. Furthermore the load dependency itself of a certain noise contribution can be strengthened, which allows for a dynamic sound character comparable to sporty gasoline vehicles. (orig.)

  3. Swiss fuel cell passenger and pleasure boats

    Energy Technology Data Exchange (ETDEWEB)

    Affolter, J.-F.

    2000-07-01

    This paper published by the University of Applied Science in Yverdon-les-Bains, Switzerland, looks at the development of electrically driven small boats that are powered by fuel cells. The various implementations of the test boats are described. Starting with a 100-watt PEM fuel cell built by the Paul Scherrer Institute (PSI) and the University of Applied Science in Solothurn, Switzerland, for educational purposes, a small pedal-boat was electrified. The paper describes the development of four further prototypes and introduces a new project for a 6-passenger leisure boat powered by a 2 kW PEFC fuel cell. Apart from the fuel cells, various other components such as propellers and control electronics are discussed as are the remaining problems still to be solved before the cells and boats can be marketed. Since they were carried out at a technical university, these projects are said to have provided an excellent way of teaching new technologies to students.

  4. 03. Disruption Management in PassengerTransportation - from Air to Tracks

    OpenAIRE

    Clausen, Jens

    2007-01-01

    Over the last 10 years there has been a tremendous growth in air transportation of passengers. Both airports and airspace are close to saturation with respect to capacity, leading to delays caused by disruptions. At the same time the amount of vehicular traffic around and in all larger cities of the world has show a dramatic increase as well. Public transportation by e.g. rail has come into focus, and hence also the service level provided by suppliers ad public transportatio...

  5. One thousand years of fires: Integrating proxy and model data

    Directory of Open Access Journals (Sweden)

    Natalie Marie Kehrwald

    2016-04-01

    Full Text Available The current fires raging across Indonesia are emitting more carbon than the annual fossil fuel emissions of Germany or Japan, and the fires are still consuming vast tracts of rainforest and peatlands. The National Interagency Fire Center (www.nifc.gov notes that 2015 is one worst fire years on record in the U.S., where more than 9 million acres burned -- equivalent to the combined size of Massachusetts and New Jersey. The U.S. and Indonesian fires have already displaced tens of thousands of people, and their impacts on ecosystems are still unclear. In the case of Indonesia, the burning peat is destroying much of the existing soil, with unknown implications for the type of vegetation regrowth. Such large fires result from a combination of fire management practices, increasing anthropogenic land use, and a changing climate. The expected increase in fire activity in the upcoming decades has led to a surge in research trying to understand their causes, the factors that may have influenced similar times of fire activity in the past, and the implications of such fire activity in the future. Multiple types of complementary data provide information on the impacts of current fires and the extent of past fires. The wide array of data encompasses different spatial and temporal resolutions (Figure 1 and includes fire proxy information such as charcoal and tree ring fire scars, observational records, satellite products, modern emissions data, fire models within global land cover and vegetation models, and sociodemographic data for modeling past human land use and ignition frequency. Any single data type is more powerful when combined with another source of information. Merging model and proxy data enables analyses of how fire activity modifies vegetation distribution, air and water quality, and proximity to cities; these analyses in turn support land management decisions relating to conservation and development.

  6. Human Thermal Comfort and Heat Removal Efficiency for Ventilation Variants in Passenger Cars

    Directory of Open Access Journals (Sweden)

    Saboora Khatoon

    2017-10-01

    Full Text Available The realization of a comfortable thermal environment with low energy consumption and improved ventilation in a car has become the aim of manufacturers in recent decades. Novel ventilation concepts with more flexible cabin usage and layouts are appealing owing to their potential for improving passenger comfort and driving power. In this study, three variant ventilation concepts are investigated and their performance is compared with respect to energy efficiency and human comfort of the driver and passenger in front and a child in the rear compartment. FLUENT 16.0, a commercial three-dimensional (3D software, are used for the simulation. A surface-to-surface radiation model is applied under transient conditions for a car parked in summer conditions with its engine in the running condition. The results for the standard Fanger’s model and modified Fanger’s model are analyzed, discussed, and compared for the driver, passenger, and child. The modified Fanger’s model determines the thermal sensation on the basis of mean arterial pressure.

  7. The Simultaneous Vehicle Scheduling and Passenger Service Problem

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann; Larsen, Allan; Madsen, Oli B.G.

    modifications of the timetable during the vehicle scheduling phase. This planning approach is referred to as the Simultaneous Vehicle Scheduling and Passenger Service Problem (SVSPSP). The SVSPSP is solved using a large neighbourhood search metaheuristic. The proposed framework is tested on data inspired......Passengers using public transport systems often experience waiting times when transferring between two scheduled services. We propose a planning approach which seeks to obtain a favorable trade-off between the conflicting objectives passenger service and operating cost, by allowing some moderate...

  8. Multi-year predictability in a coupled general circulation model

    Energy Technology Data Exchange (ETDEWEB)

    Power, Scott; Colman, Rob [Bureau of Meteorology Research Centre, Melbourne, VIC (Australia)

    2006-02-01

    Multi-year to decadal variability in a 100-year integration of a BMRC coupled atmosphere-ocean general circulation model (CGCM) is examined. The fractional contribution made by the decadal component generally increases with depth and latitude away from surface waters in the equatorial Indo-Pacific Ocean. The relative importance of decadal variability is enhanced in off-equatorial ''wings'' in the subtropical eastern Pacific. The model and observations exhibit ''ENSO-like'' decadal patterns. Analytic results are derived, which show that the patterns can, in theory, occur in the absence of any predictability beyond ENSO time-scales. In practice, however, modification to this stochastic view is needed to account for robust differences between ENSO-like decadal patterns and their interannual counterparts. An analysis of variability in the CGCM, a wind-forced shallow water model, and a simple mixed layer model together with existing and new theoretical results are used to improve upon this stochastic paradigm and to provide a new theory for the origin of decadal ENSO-like patterns like the Interdecadal Pacific Oscillation and Pacific Decadal Oscillation. In this theory, ENSO-driven wind-stress variability forces internal equatorially-trapped Kelvin waves that propagate towards the eastern boundary. Kelvin waves can excite reflected internal westward propagating equatorially-trapped Rossby waves (RWs) and coastally-trapped waves (CTWs). CTWs have no impact on the off-equatorial sub-surface ocean outside the coastal wave guide, whereas the RWs do. If the frequency of the incident wave is too high, then only CTWs are excited. At lower frequencies, both CTWs and RWs can be excited. The lower the frequency, the greater the fraction of energy transmitted to RWs. This lowers the characteristic frequency of variability off the equator relative to its equatorial counterpart. Both the eastern boundary interactions and the accumulation of

  9. Dynamical Downscaling of NASA/GISS ModelE: Continuous, Multi-Year WRF Simulations

    Science.gov (United States)

    Otte, T.; Bowden, J. H.; Nolte, C. G.; Otte, M. J.; Herwehe, J. A.; Faluvegi, G.; Shindell, D. T.

    2010-12-01

    The WRF Model is being used at the U.S. EPA for dynamical downscaling of the NASA/GISS ModelE fields to assess regional impacts of climate change in the United States. The WRF model has been successfully linked to the ModelE fields in their raw hybrid vertical coordinate, and continuous, multi-year WRF downscaling simulations have been performed. WRF will be used to downscale decadal time slices of ModelE for recent past, current, and future climate as the simulations being conducted for the IPCC Fifth Assessment Report become available. This presentation will focus on the sensitivity to interior nudging within the RCM. The use of interior nudging for downscaled regional climate simulations has been somewhat controversial over the past several years but has been recently attracting attention. Several recent studies that have used reanalysis (i.e., verifiable) fields as a proxy for GCM input have shown that interior nudging can be beneficial toward achieving the desired downscaled fields. In this study, the value of nudging will be shown using fields from ModelE that are downscaled using WRF. Several different methods of nudging are explored, and it will be shown that the method of nudging and the choices made with respect to how nudging is used in WRF are critical to balance the constraint of ModelE against the freedom of WRF to develop its own fields.

  10. The effectiveness of lane departure warning systems-A reduction in real-world passenger car injury crashes.

    Science.gov (United States)

    Sternlund, Simon; Strandroth, Johan; Rizzi, Matteo; Lie, Anders; Tingvall, Claes

    2017-02-17

    The objective of this study was to estimate the safety benefits of in vehicle lane departure warning (LDW) and lane keeping aid (LKA) systems in reducing relevant real-world passenger car injury crashes. The study used an induced exposure method, where LDW/LKA-sensitive and nonsensitive crashes were compared for Volvo passenger cars equipped with and without LDW/LKA systems. These crashes were matched by car make, model, model year, and technical equipment; that is, low-speed autonomous emergency braking (AEB) called City Safety (CS). The data were extracted from the Swedish Traffic Accident Data Acquisition database (STRADA) and consisted of 1,853 driver injury crashes that involved 146 LDW-equipped cars, 11 LKA-equipped cars, and 1,696 cars without LDW/LKA systems. The analysis showed a positive effect of the LDW/LKA systems in reducing lane departure crashes. The LDW/LKA systems were estimated to reduce head-on and single-vehicle injury crashes on Swedish roads with speed limits between 70 and 120 km/h and with dry or wet road surfaces (i.e., not covered by ice or snow) by 53% with a lower limit of 11% (95% confidence interval [CI]). This reduction corresponded to a reduction of 30% with a lower limit of 6% (95% CI) for all head-on and single-vehicle driver injury crashes (including all speed limits and all road surface conditions). LDW/LKA systems were estimated to lower the driver injury risk in crash types that the systems are designed to prevent; that is, head-on and single-vehicle crashes. Though these are important findings, they were based on a small data set. Therefore, further research is desirable to evaluate the effectiveness of LDW/LKA systems under real-world conditions and to differentiate the effectiveness between technical solutions (i.e., LDW and LKA) proposed by different manufacturers.

  11. Time Series Forecasting of the Number of Malaysia Airlines and AirAsia Passengers

    Science.gov (United States)

    Asrah, N. M.; Nor, M. E.; Rahim, S. N. A.; Leng, W. K.

    2018-04-01

    The standard practice in forecasting process involved by fitting a model and further analysis on the residuals. If we know the distributional behaviour of the time series data, it can help us to directly analyse the model identification, parameter estimation, and model checking. In this paper, we want to compare the distributional behaviour data from the number of Malaysia Airlines (MAS) and AirAsia passenger’s. From the previous research, the AirAsia passengers are govern by geometric Brownian motion (GBM). The data were normally distributed, stationary and independent. Then, GBM was used to forecast the number of AirAsia passenger’s. The same methods were applied to MAS data and the results then were compared. Unfortunately, the MAS data were not govern by GBM. Then, the standard approach in time series forecasting will be applied to MAS data. From this comparison, we can conclude that the number of AirAsia passengers are always in peak season rather than MAS passengers.

  12. Sustainable passenger road transport scenarios to reduce fuel consumption, air pollutants and GHG (greenhouse gas) emissions in the Mexico City Metropolitan Area

    International Nuclear Information System (INIS)

    Chavez-Baeza, Carlos; Sheinbaum-Pardo, Claudia

    2014-01-01

    This paper presents passenger road transport scenarios that may assist the MCMA (Mexico City Metropolitan Area) in achieving lower emissions in both criteria air pollutants (CO, NO x , NMVOC (non-methane volatile organic compounds), and PM 10 ) and GHG (greenhouse gas) (CH 4 , N 2 O and CO 2 ), while also promoting better mobility and quality of life in this region. We developed a bottom-up model to estimate the historical trends of energy demand, criteria air pollutants and GHG emissions caused by passenger vehicles circulating in the Mexico City Metropolitan Area (MCMA) in order to construct a baseline scenario and two mitigation scenarios that project their impact to 2028. Mitigation scenario “eff” considers increasing fuel efficiencies and introducing new technologies for vehicle emission controls. Mitigation scenario “BRT” considers a modal shift from private car trips to a Bus Rapid Transport system. Our results show significant reductions in air pollutants and GHG emissions. Incentives and environmental regulations are needed to enable these scenarios. - Highlights: • More than 4.2 million passenger vehicles in the MCMA (Mexico City Metropolitan Area) that represent 61% of criteria pollutants and 44% of GHG (greenhouse gas) emissions. • Emissions of CO, NO x and NMVOC (non-methane volatile organic compounds) in baseline scenario decrease with respect to its 2008 value because emission standards. • Emissions of PM 10 and GHG increase in baseline scenario. • Emissions of PM 10 and GHG decrease in eff + BRT scenario from year 2020. • Additional reductions are possible with better standards for diesel vehicles and other technologies

  13. Controlling air pollution from passenger ferries: cost-effectiveness of seven technological options.

    Science.gov (United States)

    Farrell, Alexander E; Corbett, James J; Winebrake, James J

    2002-12-01

    Continued interest in improving air quality in the United States along with renewed interest in the expansion of urban passenger ferry service has created concern about air pollution from ferry vessels. This paper presents a methodology for estimating the air pollution emissions from passenger ferries and the costs of emissions control strategies. The methodology is used to estimate the emissions and costs of retrofitting or re-powering ferries with seven technological options (combinations of propulsion and emission control systems) onto three vessels currently in service in San Francisco Bay. The technologies include improved engine design, cleaner fuels (including natural gas), and exhaust gas cleanup devices. The three vessels span a range of ages and technologies, from a 25-year-old monohull to a modern, high-speed catamaran built only four years ago. By looking at a range of technologies, vessel designs, and service conditions, a sense of the broader implications of controlling emissions from passenger ferries across a range of vessels and service profiles is provided. Tier 2-certified engines are the most cost-effective choice, but all options are cost-effective relative to other emission control strategies already in place in the transportation system.

  14. Ticket Fare Optimization for China’s High-Speed Railway Based on Passenger Choice Behavior

    Directory of Open Access Journals (Sweden)

    Jinzi Zheng

    2017-01-01

    Full Text Available Although China’s high-speed railway (HSR is maturing after more than ten years of construction and development, the load factor and revenue of HSR could still be improved by optimizing the ticket fare structure. Different from the present unitary and changeless fare structure, this paper explores the application of multigrade fares to China’s HSR. On the premise that only one fare grade can be offered for each origin-destination (O-D at the same time, this paper addresses the questions of how to adjust ticket price over time to maximize the revenue. First, on the basis of piecewise pricing strategy, a ticket fare optimization model is built, which could be transformed to convex program to be solved. Then, based on the analysis of passenger arrival regularity using historical ticket data of Beijing-Shanghai HSR line, several experiments are performed using the method proposed in the paper to explore the properties of the optimal multigrade fare scheme.

  15. Estimating passenger numbers in trains using existing weighing capabilities

    DEFF Research Database (Denmark)

    Nielsen, Bo Friis; Frølich, Laura; Nielsen, Otto Anker

    2013-01-01

    trains to control braking. This technique makes passenger counting cheaper and ensures a complete sample. The paper compares numbers estimated by this technique with manual counts and counts from an infrared system in trains in urban Copenhagen. It shows that the weighing system provides more accurate......Knowing passenger numbers is important for the planning and operation of the urban rail systems. Manual and electronic counting systems (typically infrared or video) are expensive and therefore entail small sample sizes. They usually count boarding and alighting passengers, which means that errors...... in estimates of total numbers of passengers propagate along train runs. Counting errors in manual and electronic counting systems are typically flow-dependent, making uncertainty a function of volume. This paper presents a new counting technique that exploits the weighing systems installed in most modern...

  16. Research on the compressive strength of a passenger vehicle roof

    Science.gov (United States)

    Zhao, Guanglei; Cao, Jianxiao; Liu, Tao; Yang, Na; Zhao, Hongguang

    2017-05-01

    To study the compressive strength of a passenger vehicle roof, this paper makes the simulation test on the static collapse of the passenger vehicle roof and analyzes the stress and deformation of the vehicle roof under pressure in accordance with the Roof Crush Resistance of Passenger Cars (GB26134-2010). It studies the optimization on the major stressed parts, pillar A, pillar B and the rail of roof, during the static collapse process of passenger vehicle roof. The result shows that the thickness of pillar A and the roof rail has significant influence on the compressive strength of the roof while that of pillar B has minor influence on the compressive strength of the roof.

  17. Intercity passenger rail : financial performance of Amtrak's routes

    Science.gov (United States)

    1998-05-14

    Since it began operations in 1971, the National Railroad Passenger Corporation : (Amtrak) has never been profitable and has received about $21 billion in federal : subsidies for operating and capital expenses. In December 1994, at the : direction of ...

  18. Ejection of a rear facing, golf cart passenger.

    Science.gov (United States)

    Schau, Kyle; Masory, Oren

    2013-10-01

    The following report details the findings of a series of experiments and simulations performed on a commercially available, shuttle style golf cart during several maneuvers involving rapid accelerations of the vehicle. It is determined that the current set of passive restraints on these types of golf carts are not adequate in preventing ejection of a rear facing passenger during rapid accelerations in the forward and lateral directions. Experimental data and simulations show that a hip restraint must be a minimum of 13 in. above the seat in order to secure a rear facing passenger during sharp turns, compared to the current restraint height of 5 in. Furthermore, it is determined that a restraint directly in front of the rear facing passenger is necessary to prevent ejection. In addressing these issues, golf cart manufacturers could greatly reduce the likelihood of injury due to ejection of a rear facing, golf cart passenger. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Specific climate impact of passenger and freight transport

    Science.gov (United States)

    2010-01-01

    Emissions of short-lived species contribute significantly to : the climate impact of transportation. The magnitude of the effects : varies over time for each transport mode. This paper compares : first the absolute climate impacts of current passenge...

  20. Crippling test of a Budd Pioneer passenger car

    Science.gov (United States)

    2012-04-16

    This research program was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development in support of the advancement of improved safety standards for passenger rail vehicles. FRA and the Volpe National Transportation Syst...

  1. Occupant Volume Integrity Evaluation in Passenger Rail Cars

    Science.gov (United States)

    2012-02-01

    This research, which is intended to enable the growth of high-speed and intercity passenger rail transportation, was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development, as part of the train Occupant Protection r...

  2. High-speed and intercity passenger rail testing strategy.

    Science.gov (United States)

    2013-05-01

    This high-speed and intercity passenger rail (HSIPR) testing strategy addresses the requirements for testing of high-speed train sets and technology before introduction to the North American railroad system. The report documents the results of a surv...

  3. Medical emergencies on large passenger ships without doctors: the Oslo-Kiel-Oslo ferry experience.

    Science.gov (United States)

    Holt, Thor-Erik; Tveten, Agnar; Dahl, Eilif

    2017-01-01

    The Oslo-Kiel-Oslo route is currently the only direct ferry crossing between Norway and Germany, covered by 2 cruise-and-cars ferries carrying about 2,600 passengers each and sailing every day (20 h at sea, 4 h in port). Unlike most ocean going cruise vessels, they are not required to carry a physician but an on-board paramedic handles medical emergencies. The aim of the study was to provide data on medical emergencies leading to helicopter evacuations (helivacs) or other urgent transfers to facilities ashore from the two ferries during a 3-year period. Data about the ferries, passengers, crew, helivacs and other medical transfers were collected from official company statistics and the paramedics' transfer reports. A total of 169 persons, including 14 (8.3%) crewmembers, were transferred from the ferries to land-based facilities by ambulance while alongside (n = 80; 47.3%) or evacuated by helicopter (n = 85; 50.3%) and rescue boat (n = 4; 2.4%) during the 3-year period. Transfer destinations were Denmark (n = 53), Germany (n = 49), Norway (n = 48) and Sweden (n = 19). The passenger helivac rate was 2.4 per 100,000 passenger-days. One person was airlifted from a ferry every 2 weeks. Among helivacs, 40% were heart-related, and more cardiac cases were airlifted than transferred by ambulance in port. All helivac requests were made after discussion between the ferry's paramedic and telemedical doctors ashore and agreement that the medical challenge exceeded the ferry's capability. This close cooperation kept the threshold for arranging helivacs from the ferries low, enabling short transport times to land-based facilities for critically ill patients. Further studies, including feedback from the receiving hospitals, are needed to determine measures that can reduce possible helicopter overutilisation without compromising patient safety and outcome.

  4. Estimating bus passenger waiting times from incomplete bus arrivals data

    OpenAIRE

    McLeod, F.N.

    2007-01-01

    This paper considers the problem of estimating bus passenger waiting times at bus stops using incomplete bus arrivals data. This is of importance to bus operators and regulators as passenger waiting time is a key performance measure. Average waiting times are usually estimated from bus headways, that is, time gaps between buses. It is both time-consuming and expensive to measure bus arrival times manually so methods using automatic vehicle location systems are attractive; however, these syste...

  5. Study to develop improved fire resistant aircraft passenger seat materials

    Science.gov (United States)

    Duskin, F. E.; Schutter, K. J.; Sieth, H. H.; Trabold, E. L.

    1980-01-01

    The Phase 3 study of the NASA 'Improved Fire Resistant Aircraft Seat Materials' involved fire tests of improved materials in multilayered combinations representative of cushion configurations. Tests were conducted to determine their thermal, smoke, and fire resistance characteristics. Additionally, a 'Design Guideline' for Fire Resistant Passenger Seats was written outlining general seat design considerations. Finally, a three-abreast 'Tourist Class' passenger seat assembly fabricated from the most advanced fire-resistant materials was delivered.

  6. Fire-resistant materials for aircraft passenger seat construction

    Science.gov (United States)

    Fewell, L. L.; Tesoro, G. C.; Moussa, A.; Kourtides, D. A.

    1979-01-01

    The thermal response characteristics of fabric and fabric-foam assemblies are described. The various aspects of the ignition behavior of contemporary aircraft passenger seat upholstery fabric materials relative to fabric materials made from thermally stable polymers are evaluated. The role of the polymeric foam backing on the thermal response of the fabric-foam assembly is also ascertained. The optimum utilization of improved fire-resistant fabric and foam materials in the construction of aircraft passenger seats is suggested.

  7. Influence of Unsteady Aerodynamics on Driving Dynamics of Passenger Cars

    OpenAIRE

    Huemer, J.; Stickel, T.; Sagan, E.; Schwarz, M.; Wall, W.A.

    2015-01-01

    Recent approaches towards numerical investigations with CFD-Methods on unsteady aerodynamic loads of passenger cars identified major differences compared to steady state aerodynamic excitations. Furthermore innovative vehicle concepts like electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve...

  8. Determiantion of elasticity coefficient of demand for suburban passenger transport

    Directory of Open Access Journals (Sweden)

    Тетяна Михайлівна Григорова

    2015-06-01

    Full Text Available The regularity of changes in demand for suburban passenger road transport, depending on the value, is investigated. The results of the survey of passengers about changes of fare on the chosen route are given. It is built the curve of elasticity of demand for suburban bus transport use in labor and cultural and social movements. The equilibrium tariff for suburban road transport is defined

  9. An Optimization Method of Passenger Assignment for Customized Bus

    OpenAIRE

    Yang Cao; Jian Wang

    2017-01-01

    This study proposes an optimization method of passenger assignment on customized buses (CB). Our proposed method guarantees benefits to passengers by balancing the elements of travel time, waiting time, delay, and economic cost. The optimization problem was solved using a Branch and Bound (B&B) algorithm based on the shortest path for the selected stations. A simulation-based evaluation of the proposed optimization method was conducted. We find that a CB service can save 38.33% in average tra...

  10. 77 FR 25105 - Reporting of Ancillary Airline Passenger Revenues

    Science.gov (United States)

    2012-04-27

    ...This document announces a public meeting on a Notice of Proposed Rulemaking (NPRM) issued on July 15, 2011. The NPRM proposed changes regarding reporting of airline ancillary passenger revenues, computation of mishandled baggage rates, and collection of separate statistics for mishandled wheelchairs and scooters used by passengers with disabilities. During the public meeting, DOT staff will provide a summary of the proposals in the NPRM and seek input on costs and benefits associated with the implementation of the proposals.

  11. FORECASTING OF PASSENGER TRAFFIC UPON IMPLEMENTATION OF HIGH-SPEED RUNNING

    Directory of Open Access Journals (Sweden)

    M. B. Kurhan

    2017-02-01

    Full Text Available Purpose. Forecasting of passenger traffic flows in the future is an essential and integral part of the complex process of designing of high-speed network (HSN. HSN direction and its parameters are determined by the volume of passenger traffic, the estimated value of which depends on the economic performance of the country, as well as the material status of citizens living in HSN concentration area, transport mobility of population, development of competing modes of transport and so on. The purpose of this work is to analyse the existing methods of passenger traffic forecasting, to evaluate errors of the existing models concerning determination of traffic volumes and to specify the scientific approach to the development of high-speed rail transport in Ukraine. Methodology. The existing forecasting methods are reduced to the following ones: Delphi approach, extrapolation method, factor and correlation analysis, simulation method. The method described in this paper is based on scientific approaches such as analysis – a comprehensive and detailed study of various aspects of the known forecasting methods, comparing of existing methods for establishing differences and similarities, as well as deduction – use of general knowledge to get the new particular one. Thus, the unified indicators determined for the country as a whole, such as gross domestic product, national income, total population and others cannot be used to forecast the traffic flow on specific areas of HSN construction. Therefore, it is necessary to move from the overall forecast to traffic volume forecast on particular direction. Findings. The conclusions are derived from the analysis of different approaches and methods of passenger flow forecasting. It is proposed to create typical techniques of traffic flow forecasting using modern mathematical methods that would allow avoiding unreasonable decisions and shortening project development time. The resulting recommendations will help

  12. Real-time passenger counting by active linear cameras

    Science.gov (United States)

    Khoudour, Louahdi; Duvieubourg, Luc; Deparis, Jean-Pierre

    1996-03-01

    The companies operating subways are very much concerned with counting the passengers traveling through their transport systems. One of the most widely used systems for counting passengers consists of a mechanical gate equipped with a counter. However, such simple systems are not able to count passengers jumping above the gates. Moreover, passengers carrying large luggage or bags may meet some difficulties when going through such gates. The ideal solution is a contact-free counting system that would bring more comfort of use for the passengers. For these reasons, we propose to use a video processing system instead of these mechanical gates. The optical sensors discussed in this paper offer several advantages including well defined detection areas, fast response time and reliable counting capability. A new technology has been developed and tested, based on linear cameras. Preliminary results show that this system is very efficient when the passengers crossing the optical gate are well separated. In other cases, such as in compact crowd conditions, reasonable accuracy has been demonstrated. These results are illustrated by means of a number of sequences shot in field conditions. It is our belief that more precise measurements could be achieved, in the case of compact crowd, by other algorithms and acquisition techniques of the line images that we are presently developing.

  13. Designing Train Passenger Seat by Kansei Engineering in Indonesia

    Directory of Open Access Journals (Sweden)

    Hapsari Sakya Nabila

    2017-01-01

    Full Text Available Public transport adoption is still major problem in Indonesia. Integrating impression and emotion to service may change the image of public transport, leading to fast adoption rate. As product development technique, Kansei Engineering is well known to facilitate that integration. This paper communicates the implementation of Kansei Engineering (KE in designing train passenger seat in Indonesia. The train between Bandung-Solo (8 hours journey was chosen to be the investigated object. The train was selected to be refurbished by introducing a new passenger seat design, emphasizing on the improvement of passenger experience. As the first step of KE type I technique, travel experience of the existing passengers were taken into the consideration for selecting Kansei words. It was found that the relevant Kansei words to design passenger train seat in Indonesia were: comfort, people-friendly, multifunction, safe, soft, spacious, relaxing, superior, maintainable, strong, producible, minimalist, attractive, modern, unique, and durable. Upon understanding the semantic meaning of those words, physical properties and technical specification were produced by consulting to the related members. Finally, a passenger seat with synthetic leather cover, modular design, foldable table, individual power point, bluesilver color, and adjusted to Indonesian’s anthropometry data was proposed as the final design

  14. Ecological Pressure of Carbon Footprint in Passenger Transport: Spatio-Temporal Changes and Regional Disparities

    Directory of Open Access Journals (Sweden)

    Fei Ma

    2018-01-01

    Full Text Available Passenger transport has become a significant producer of carbon emissions in China, thus strongly contributing to climate change. In this paper, we first propose a model of ecological pressure of the carbon footprint in passenger transport (EPcfpt. In the model, the EPcfpt values of all the provinces and autonomous regions of China are calculated and analyzed during the period of 2006–2015. For the outlier EPcfpt values of Beijing, Shanghai and Tianjin, the research areas are classified into two scenarios: the first scenario (all the provinces and autonomous regions and the second scenario (not including Beijing, Shanghai and Tianjin. The global spatial autocorrelation analysis of the first scenario shows that the EPcfpt might be randomly distributed, while it shows positive spatial autocorrelation in the second scenario. Furthermore, we carry out the local spatial autocorrelation analysis of the second scenario, and find that the low aggregation areas are the most common type and are mainly located in the west of China. Then the disparities in EPcfpt between China’s Eight Comprehensive Economic Zones are further analyzed. Finally, we put forward a number of policy recommendations in relation to the spatio-temporal changes and the regional disparities of EPcfpt in China. This study provides related references for proposing effective policy measures to reduce the ecological pressure of carbon emissions from the passenger transport sector.

  15. Eight Year Climatologies from Observational (AIRS) and Model (MERRA) Data

    Science.gov (United States)

    Hearty, Thomas; Savtchenko, Andrey; Won, Young-In; Theobalk, Mike; Vollmer, Bruce; Manning, Evan; Smith, Peter; Ostrenga, Dana; Leptoukh, Greg

    2010-01-01

    We examine climatologies derived from eight years of temperature, water vapor, cloud, and trace gas observations made by the Atmospheric Infrared Sounder (AIRS) instrument flying on the Aqua satellite and compare them to similar climatologies constructed with data from a global assimilation model, the Modern Era Retrospective-Analysis for Research and Applications (MERRA). We use the AIRS climatologies to examine anomalies and trends in the AIRS data record. Since sampling can be an issue for infrared satellites in low earth orbit, we also use the MERRA data to examine the AIRS sampling biases. By sampling the MERRA data at the AIRS space-time locations both with and without the AIRS quality control we estimate the sampling bias of the AIRS climatology and the atmospheric conditions where AIRS has a lower sampling rate. While the AIRS temperature and water vapor sampling biases are small at low latitudes, they can be more than a few degrees in temperature or 10 percent in water vapor at higher latitudes. The largest sampling biases are over desert. The AIRS and MERRA data are available from the Goddard Earth Sciences Data and Information Services Center (GES DISC). The AIRS climatologies we used are available for analysis with the GIOVANNI data exploration tool. (see, http://disc.gsfc.nasa.gov).

  16. Acoustic Vocal Tract Model of One-year-old Children

    Directory of Open Access Journals (Sweden)

    M. Vojnović

    2014-11-01

    Full Text Available The physical shape of vocal tract and its formant (resonant frequencies are directly related. The study of this functional connectivity is essential in speech therapy practice with children. Most of the perceived children’s speech anomalies can be explained on a physical level: malfunctioning movement of articulation organs. The current problem is that there is no enough data on the anatomical shape of children’s vocal tract to create its acoustic model. Classical techniques for vocal tract shape imaging (X-ray, magnetic resonance, etc. are not appropriate for children. One possibility is to start from the shape of the adult vocal tract and correct it based on anatomical, morphological and articulatory differences between children and adults. This paper presents a method for vocal tract shape estimation of the child aged one year. The initial shapes of the vocal tract refer to the Russian vowels spoken by an adult male. All the relevant anatomical and articulation parameters, that influence the formant frequencies, are analyzed. Finally, the hypothetical configurations of the children’s vocal tract, for the five vowels, are presented.

  17. Driver or passenger effects of augmented c-Myc and Cdc20 in gliomagenesis.

    Science.gov (United States)

    Ji, Ping; Zhou, Xinhui; Liu, Qun; Fuller, Gregory N; Phillips, Lynette M; Zhang, Wei

    2016-04-26

    Cdc20 and c-Myc are commonly overexpressed in a broad spectrum of cancers, including glioblastoma (GBM). Despite this clear association, whether c-Myc and Cdc20 overexpression is a driver or passenger event in gliomagenesis remains unclear. Both c-Myc and Cdc20 induced the proliferation of primary glial progenitor cells. c-Myc also promoted the formation of soft agar anchorage-independent colonies. In the RCAS/Ntv-a glia-specific transgenic mouse model, c-Myc increased the GBM incidence from 19.1% to 47.4% by 12 weeks of age when combined with kRas and Akt3 in Ntv-a INK4a-ARF (also known as CDKN2A)-null mice. In contrast, Cdc20 decreased the GBM incidence from 19.1% to 9.1%. Moreover, cell differentiation was modulated by c-Myc in kRas/Akt3-induced GBM on the basis of Nestin/GFAP expression (glial progenitor cell differentiation), while Cdc20 had no effect on primary glial progenitor cell differentiation. We used glial progenitor cells from Ntv-a newborn mice to evaluate the role of c-Myc and Cdc20 in the proliferation and transformation of GBM in vitro and in vivo. We further determined whether c-Myc and Cdc20 have a driver or passenger role in GBM development using kRas/Akt3 signals in a RCAS/Ntv-a mouse model. These results suggest that the driver or passenger of oncogene signaling is dependent on cellular status. c-Myc is a driver when combined with kRas/Akt3 oncogenic signals in gliomagenesis, whereas Cdc20 overexpression is a passenger. Inhibition of cell differentiation of c-Myc may be a target for anti-glioma therapy.

  18. Energy consumption and environmental effects of passenger transport modes. A life cycle study on passenger transport modes

    International Nuclear Information System (INIS)

    Kalenoja, H.

    1996-01-01

    Energy consumption and environmental effects of different passenger transport modes vary on the different stages of the fuel chain and during the production and maintenance of vehicles and infrastructure. Energy consumption and the environmental effects calculated per passenger mileage depend strongly on the vehicle occupancy. The properties of transport modes on urban areas and on the long distance transport have been evaluated in this study. The energy consumption and environmental effects calculated per passenger mileage have been assessed for passenger car, bus, tram, train, airplane and ferry. The emissions have been evaluated during the whole fuel chain. In this study only the airborne emissions have been taken into account. In the energy consumption calculations the energy content of vehicles and the infrastructure, energy consumption during the fuel chain and during the end use have been taken into consideration. (au)

  19. Examining the Relationship Between Passenger Airline Aircraft Maintenance Outsourcing and Aircraft Safety

    Science.gov (United States)

    Monaghan, Kari L.

    The problem addressed was the concern for aircraft safety rates as they relate to the rate of maintenance outsourcing. Data gathered from 14 passenger airlines: AirTran, Alaska, America West, American, Continental, Delta, Frontier, Hawaiian, JetBlue, Midwest, Northwest, Southwest, United, and USAir covered the years 1996 through 2008. A quantitative correlational design, utilizing Pearson's correlation coefficient, and the coefficient of determination were used in the present study to measure the correlation between variables. Elements of passenger airline aircraft maintenance outsourcing and aircraft accidents, incidents, and pilot deviations within domestic passenger airline operations were analyzed, examined, and evaluated. Rates of maintenance outsourcing were analyzed to determine the association with accident, incident, and pilot deviation rates. Maintenance outsourcing rates used in the evaluation were the yearly dollar expenditure of passenger airlines for aircraft maintenance outsourcing as they relate to the total airline aircraft maintenance expenditures. Aircraft accident, incident, and pilot deviation rates used in the evaluation were the yearly number of accidents, incidents, and pilot deviations per miles flown. The Pearson r-values were calculated to measure the linear relationship strength between the variables. There were no statistically significant correlation findings for accidents, r(174)=0.065, p=0.393, and incidents, r(174)=0.020, p=0.793. However, there was a statistically significant correlation for pilot deviation rates, r(174)=0.204, p=0.007 thus indicating a statistically significant correlation between maintenance outsourcing rates and pilot deviation rates. The calculated R square value of 0.042 represents the variance that can be accounted for in aircraft pilot deviation rates by examining the variance in aircraft maintenance outsourcing rates; accordingly, 95.8% of the variance is unexplained. Suggestions for future research include

  20. Energy Chain Analysis of Passenger Car Transport

    Directory of Open Access Journals (Sweden)

    Hans Jakob Walnum

    2011-02-01

    Full Text Available Transport makes up 20 percent of the World’s energy use; in OECD countries this has exceeded 30 percent. The International Energy Agency (IEA estimates that the global energy consumption will increase by 2.1 percent annually, a growth rate that is higher than for any other sector. The high energy consumption means that transportation accounts for nearly 30 percent of CO2 emission in OECD countries and is also one of the main sources of regional and local air pollution. In this article, we analyze energy consumption and greenhouse gas emissions from passenger car transport using an energy chain analysis. The energy chain analysis consists of three parts: the net direct energy use, the energy required for vehicle propulsion; the gross direct chain, which includes the net direct energy consumption plus the energy required to produce it; and, finally, the indirect energy chain, which includes the energy consumption for production, maintenance and operation of infrastructure plus manufacturing of the vehicle itself. In addition to energy consumption, we also analyze emissions of greenhouse gases measured by CO2-equivalents. We look at the trade-offs between energy use and greenhouse gas emissions to see whether some drivetrains and fuels perform favourable on both indicators. Except for the case of electric cars, where hydropower is the only energy source in the Norwegian context, no single car scores favourably on both energy consumption and greenhouse gas emissions.

  1. A lightweight electronically commutated dc motor for electric passenger vehicles

    Science.gov (United States)

    Echolds, E. F.; Walla, P. S.

    1982-01-01

    A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

  2. A lightweight electronically commutated dc motor for electric passenger vehicles

    Science.gov (United States)

    Echolds, E. F.; Walla, P. S.

    1982-09-01

    A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

  3. Reflection of a Year Long Model-Driven Business and UI Modeling Development Project

    Science.gov (United States)

    Sukaviriya, Noi; Mani, Senthil; Sinha, Vibha

    Model-driven software development enables users to specify an application at a high level - a level that better matches problem domain. It also promises the users with better analysis and automation. Our work embarks on two collaborating domains - business process and human interactions - to build an application. Business modeling expresses business operations and flows then creates business flow implementation. Human interaction modeling expresses a UI design, its relationship with business data, logic, and flow, and can generate working UI. This double modeling approach automates the production of a working system with UI and business logic connected. This paper discusses the human aspects of this modeling approach after a year long of building a procurement outsourcing contract application using the approach - the result of which was deployed in December 2008. The paper discusses in multiple areas the happy endings and some heartache. We end with insights on how a model-driven approach could do better for humans in the process.

  4. Effects of vehicle power on passenger vehicle speeds.

    Science.gov (United States)

    McCartt, Anne T; Hu, Wen

    2017-07-04

    During the past 2 decades, there have been large increases in mean horsepower and the mean horsepower-to-vehicle weight ratio for all types of new passenger vehicles in the United States. This study examined the relationship between travel speeds and vehicle power, defined as horsepower per 100 pounds of vehicle weight. Speed cameras measured travel speeds and photographed license plates and drivers of passenger vehicles traveling on roadways in Northern Virginia during daytime off-peak hours in spring 2013. The driver licensing agencies in the District of Columbia, Maryland, and Virginia provided vehicle information numbers (VINs) by matching license plate numbers with vehicle registration records and provided the age, gender, and ZIP code of the registered owner(s). VINs were decoded to obtain the curb weight and horsepower of vehicles. The study focused on 26,659 observed vehicles for which information on horsepower was available and the observed age and gender of drivers matched vehicle registration records. Log-linear regression estimated the effects of vehicle power on mean travel speeds, and logistic regression estimated the effects of vehicle power on the likelihood of a vehicle traveling over the speed limit and more than 10 mph over the limit. After controlling for driver characteristics, speed limit, vehicle type, and traffic volume, a 1-unit increase in vehicle power was associated with a 0.7% increase in mean speed, a 2.7% increase in the likelihood of a vehicle exceeding the speed limit by any amount, and an 11.6% increase in the likelihood of a vehicle exceeding the limit by 10 mph. All of these increases were highly significant. Speeding persists as a major factor in crashes in the United States. There are indications that travel speeds have increased in recent years. The current findings suggest the trend toward substantially more powerful vehicles may be contributing to higher speeds. Given the strong association between travel speed and crash

  5. Evaluating a smartphone application to improve child passenger safety and fire safety knowledge and behaviour.

    Science.gov (United States)

    Omaki, Elise; Shields, Wendy C; McDonald, Eileen; Aitken, Mary E; Bishai, David; Case, James; Gielen, Andrea

    2017-02-01

    Although proven measures for reducing injury due to motor vehicle collision and residential fires exist, the number of families properly and consistently using child passenger restraints and smoke alarms remains low. This paper describes the design of the Safety In Seconds (SIS) 2.0 study, which aims to evaluate the impact of a smartphone app on parents' use of child restraints and smoke alarms. SIS is a multisite randomised controlled trial. Participants are parents of children aged 4-7 years who are visiting the Pediatric Emergency Department or Pediatric Trauma Service. Parents are randomised to receive tailored education about child passenger safety or about fire safety via the SIS smartphone app. A baseline and two follow-up surveys at 3 months and 6 months are conducted. Primary outcomes are: (1) having the correct child restraint for the child's age and size; (2) restraining the child in the back seat of the car; (3) buckling the child up for every ride; (4) having the restraint inspected by a child passenger safety technician; (5) having a working smoke alarm on every level of the home; (6) having hard-wired or lithium battery smoke alarms; (7) having and (8) practising a fire escape plan. Finding ways to communicate with parents about child passenger and fire safety continues to be a research priority. This study will contribute to the evidence about how to promote benefits of proper and consistent child restraint and smoke alarm use. NCT02345941; Pre-results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  6. Análise de modelo para projeto e desenvolvimento de serviços: uma pesquisa-ação em uma empresa de transporte rodoviário de passageiros Analysis of a service project and a development model: an action-research in a road passengers transport company

    Directory of Open Access Journals (Sweden)

    Vanessa Cristhina Gatto Chimendes

    2008-12-01

    Full Text Available O objetivo deste trabalho é analisar a implantação de um modelo de referência para o projeto e desenvolvimento de serviços em uma empresa de transporte rodoviário de passageiros. O intuito principal é minimizar três problemas relativos ao processo de desenvolvimento de serviços, pela ausência de: uma abordagem sistemática; documentos e registros que assegurem o controle do histórico de criação e melhorias para os serviços; testes documentados para verificação e validação do serviço desenvolvido. O modelo de referência foi escolhido por meio da análise de variância multivariada (Manova e a pesquisa empregou a estratégia da pesquisa-ação. O objeto de estudo foi o desenvolvimento de um serviço de bilhetagem eletrônica para uma empresa de transporte rodoviário. A pesquisa proporcionou recomendações para o aperfeiçoamento do modelo de referência e para a implantação de um processo sistemático de desenvolvimento de serviços para a empresa.The aim of this work is to analyze the implementation of a reference model for the project and development of services in a road passenger Transport Company. The main goals were to minimize three problems related to services development process: the absence of systematic approach, the absence of documents and records that assure the control of the services development description, and the absence of tests documentation for the verification and validation of the developed service. The reference model was chosen by using multivariate analysis of variance and the action-research strategy. A smart card payment system service development for the road passengers' transport was the object of study. The research provided recommendations of improvements for the reference model and for the implementation of a systematic service development process in the company.

  7. An epidemiological study of rates of illness in passengers and crew at a busy Caribbean cruise port

    Directory of Open Access Journals (Sweden)

    Cathy Ann Marshall

    2016-04-01

    Full Text Available Abstract Background The Caribbean has one of the largest cruise ship industries in the world, with close to 20 million visitors per year. The potential for communicable disease outbreaks on vessels and the transmission by ship between countries is high. Barbados has one of the busiest ports in the Caribbean. Our aim was to describe and analyse the epidemiology of illnesses experienced by passengers and crew arriving at the Bridgetown Port, Barbados between 2009 and 2013. Methods Data on the illnesses recorded were extracted from the passenger and crew arrival registers and passenger and crew illness logs for all ships and maritime vessels arriving at Barbados’ Ports and passing through its territorial waters between January 2009 and December 2013. Data were entered into an Epi Info database and most of the analysis undertaken using Epi Info Version 7. Rates per 100,000 visits were calculated, and confidence intervals on these were derived using the software Openepi. Results There were 1031 cases of illness from over 3 million passenger visits and 1 million crew visits during this period. The overall event rate for communicable illnesses was 15.7 (95 % CI 14.4–17.1 per 100,000 passengers, and for crew was 24.0 (21.6–26.6 per 100, 000 crew. Gastroenteritis was the predominant illness experienced by passengers and crew followed by influenza. The event rate for gastroenteritis among passengers was 13.7 (12.5–15.0 per 100,000 and 14.4 (12.6, 16.5 for crew. The event rate for non-communicable illnesses was 3.4 per 100,000 passengers with myocardial infarction being the main diagnosis. The event rate for non-communicable illnesses among crew was 2.1 per 100,000, the leading cause being injuries. Conclusions The predominant illnesses reported were gastroenteritis and influenza similar to previous published reports from around the world. This study is the first of its type in the Caribbean and the data provide a baseline for future surveillance

  8. An epidemiological study of rates of illness in passengers and crew at a busy Caribbean cruise port.

    Science.gov (United States)

    Marshall, Cathy Ann; Morris, Euclid; Unwin, Nigel

    2016-04-12

    The Caribbean has one of the largest cruise ship industries in the world, with close to 20 million visitors per year. The potential for communicable disease outbreaks on vessels and the transmission by ship between countries is high. Barbados has one of the busiest ports in the Caribbean. Our aim was to describe and analyse the epidemiology of illnesses experienced by passengers and crew arriving at the Bridgetown Port, Barbados between 2009 and 2013. Data on the illnesses recorded were extracted from the passenger and crew arrival registers and passenger and crew illness logs for all ships and maritime vessels arriving at Barbados' Ports and passing through its territorial waters between January 2009 and December 2013. Data were entered into an Epi Info database and most of the analysis undertaken using Epi Info Version 7. Rates per 100,000 visits were calculated, and confidence intervals on these were derived using the software Openepi. There were 1031 cases of illness from over 3 million passenger visits and 1 million crew visits during this period. The overall event rate for communicable illnesses was 15.7 (95 % CI 14.4-17.1) per 100,000 passengers, and for crew was 24.0 (21.6-26.6) per 100, 000 crew. Gastroenteritis was the predominant illness experienced by passengers and crew followed by influenza. The event rate for gastroenteritis among passengers was 13.7 (12.5-15.0) per 100,000 and 14.4 (12.6, 16.5) for crew. The event rate for non-communicable illnesses was 3.4 per 100,000 passengers with myocardial infarction being the main diagnosis. The event rate for non-communicable illnesses among crew was 2.1 per 100,000, the leading cause being injuries. The predominant illnesses reported were gastroenteritis and influenza similar to previous published reports from around the world. This study is the first of its type in the Caribbean and the data provide a baseline for future surveillance and for comparison with other countries and regions.

  9. Mobility chains analysis of technologies for passenger cars and light duty vehicles fueled with biofuels : application of the Greet model to project the role of biomass in America's energy future (RBAEF) project.

    Energy Technology Data Exchange (ETDEWEB)

    Wu, M.; Wu, Y.; Wang, M; Energy Systems

    2008-01-31

    The Role of Biomass in America's Energy Future (RBAEF) is a multi-institution, multiple-sponsor research project. The primary focus of the project is to analyze and assess the potential of transportation fuels derived from cellulosic biomass in the years 2015 to 2030. For this project, researchers at Dartmouth College and Princeton University designed and simulated an advanced fermentation process to produce fuel ethanol/protein, a thermochemical process to produce Fischer-Tropsch diesel (FTD) and dimethyl ether (DME), and a combined heat and power plant to co-produce steam and electricity using the ASPEN Plus{trademark} model. With support from the U.S. Department of Energy (DOE), Argonne National Laboratory (ANL) conducted, for the RBAEF project, a mobility chains or well-to-wheels (WTW) analysis using the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model developed at ANL. The mobility chains analysis was intended to estimate the energy consumption and emissions associated with the use of different production biofuels in light-duty vehicle technologies.

  10. Construction strength analysis of landing craft tank conversion to passenger ship using finite element method

    Science.gov (United States)

    Nurul Misbah, Mohammad; Setyawan, Dony; Murti Dananjaya, Wisnu

    2018-03-01

    This research aims to determine the longitudinal strength of passenger ship which was converted from Landing Craft Tank with 54 m of length as stated by BKI (Biro Klasifikasi Indonesia / Indonesian Classification Bureau). Verification of strength value is done to 4 (four) loading conditions which are (1) empty load condition during sagging wave, (2) empty load condition during hogging wave, (3) full load condition during sagging wave and (4) full load condition during hogging wave. Analysis is done using Finite Element Analysis (FEA) software by modeling the entire part of passenger ship and its loading condition. The back and upfront part of ship centerline were used as the boundary condition. From that analysis it can be concluded that the maximum stress for load condition (1) is 72,393 MPa, 74,792 MPa for load condition (2), 129,92 MPa for load condition (3), and 132,4 MPa for load condition (4). Longitudinal strength of passenger ship fulfilled the criteria of empty load condition having smaller stress value than allowable stress which is 90 MPa, and during full load condition with smaller stress value than allowable stress which is 150 MPa. Analysis on longitudinal strength comparison with entire ship plate thickness variation of ± 2 mm from initial plate was also done during this research. From this research it can be concluded that plate thickness reduction causes the value of longitudinal strength to decrease, while plate thickness addition causes the value of longitudinal strength to increase.

  11. Carbon emissions from international cruise ship passengers' travel to and from New Zealand

    Energy Technology Data Exchange (ETDEWEB)

    Howitt, Oliver J.A.; Revol, Vincent G.N.; Smith, Inga J.; Rodger, Craig J. [Department of Physics, University of Otago, PO Box 56, Dunedin (New Zealand)

    2010-05-15

    Greenhouse gas emissions from international transport contribute to anthropogenic global warming, yet these emissions are not liable under the Kyoto Protocol. International attention is being given to quantifying such emissions. This paper presents the results of research into international cruise ship journeys to and from New Zealand. CO{sub 2} emissions from such journeys were calculated using an activity based, or 'bottom-up', model. Emissions factors for individual journeys by cruise ships to or from New Zealand in 2007 ranged between 250 and 2200 g of CO{sub 2} per passenger-kilometre (g CO{sub 2} per p-km), with a weighted mean of 390 g CO{sub 2} per p-km. The weighted mean energy use per passenger night for the 'hotel' function of these cruise vessels was estimated as 1600 MJ per visitor night, 12 times larger than the value for a land-based hotel. Using a simple price elasticities calculation, international cruise journeys for transport purposes were found to have a greater relative decrease in demand than plane journeys when the impact of carbon pricing was analysed. The potential to decrease the CO{sub 2} emissions per p-km was examined, and if passenger accommodation was compacted and some luxury amenities dispensed with values similar to those of economy-class air travel were obtained. (author)

  12. Carbon emissions from international cruise ship passengers' travel to and from New Zealand

    International Nuclear Information System (INIS)

    Howitt, Oliver J.A.; Revol, Vincent G.N.; Smith, Inga J.; Rodger, Craig J.

    2010-01-01

    Greenhouse gas emissions from international transport contribute to anthropogenic global warming, yet these emissions are not liable under the Kyoto Protocol. International attention is being given to quantifying such emissions. This paper presents the results of research into international cruise ship journeys to and from New Zealand. CO 2 emissions from such journeys were calculated using an activity based, or 'bottom-up', model. Emissions factors for individual journeys by cruise ships to or from New Zealand in 2007 ranged between 250 and 2200 g of CO 2 per passenger-kilometre (g CO 2 per p-km), with a weighted mean of 390 g CO 2 per p-km. The weighted mean energy use per passenger night for the 'hotel' function of these cruise vessels was estimated as 1600 MJ per visitor night, 12 times larger than the value for a land-based hotel. Using a simple price elasticities calculation, international cruise journeys for transport purposes were found to have a greater relative decrease in demand than plane journeys when the impact of carbon pricing was analysed. The potential to decrease the CO 2 emissions per p-km was examined, and if passenger accommodation was compacted and some luxury amenities dispensed with values similar to those of economy-class air travel were obtained.

  13. Evaluation of Bus Vibration Comfort Based on Passenger Crowdsourcing Mode

    Directory of Open Access Journals (Sweden)

    Hong Zhao

    2016-01-01

    Full Text Available Vibration comfort is an important factor affecting the quality of service (QoS of bus. In order to make people involved in supervising bus’s vibration comfort and improve passengers’ riding experience, a novel mode of passenger crowdsourcing is introduced. In this paper, comfort degree of bus vibration is calculated from bus’s vibration signals collected by passengers’ smartphones and sent through WiFi to the Boa web server which shows the vibration comfort on the LCD deployed in bus and maybe trigger alarm lamp when the vibration is beyond the threshold. Three challenges here have been overcome: firstly, space coordinate transformation algorithm is used to solve the constant drift of signals collected; secondly, a low-pass filter is designed to isolate gravity from signals real-timely via limited computing resources; thirdly, an embedded evaluation system is developed according to the calculation procedure specified by criterion ISO 2631-1997. Meanwhile, the model proposed is tested in a practical running environment, the vibration data in whole travel are recorded and analyzed offline. The results show that comfort degree of vibration obtained from the experimental system is identical with the truth, and this mode is proved to be effective.

  14. The measurement of dynamic radii for passenger car tyre

    Science.gov (United States)

    Anghelache, G.; Moisescu, R.

    2017-10-01

    The tyre dynamic rolling radius is an extremely important parameter for vehicle dynamics, for operation of safety systems as ESP, ABS, TCS, etc., for road vehicle research and development, as well as for validation or as an input parameter of automotive simulations and models. The paper investigates the dynamic rolling radii of passenger car tyre and the influence of rolling speed and inflation pressure on their magnitude. The measurement of dynamic rolling radii has been performed on a chassis dynamometer test rig. The dynamic rolling radii have been measured indirectly, using longitudinal rolling speed and angular velocity of wheel. Due to the subtle effects that the parameters have on rolling radius magnitude, very accurate equipment has to be used. Two different methods have been chosen for measuring the wheel angular velocity: the stroboscopic lamp and the incremental rotary encoder. The paper shows that the stroboscopic lamp has an insufficient resolution, therefore it was no longer used for experimental investigation. The tyre dynamic rolling radii increase with rolling speed and with tyre inflation pressure, but the effect of pressure is more significant. The paper also makes considerations on the viability of simplified formulae from literature for calculating the tyre dynamic rolling radius.

  15. Congestion Tolling for Mixed Urban Freight and Passenger Traffic

    Directory of Open Access Journals (Sweden)

    Xie Chaoda

    2017-01-01

    Full Text Available This paper investigates the welfare effects of optimal tolling on urban traffic congestion, in a bottleneck model, with mixed freight and passenger users. The users’ marginal utility of time is considered to be varying with time. Under both no-toll equilibrium and socially optimal tolling, the users are found to sort their arrival time according to the increasing rates of marginal utility at the destination. The optimal toll that maximizes social welfare does not change each user's indirect utilit y relative to the no-toll equilibrium, but completely removes the queue, which also removes the barrier of freight carriers to accept congestion pricing by relating their marginal utilities directly to the toll. When the toll is equally rebated, the proposed social optimal tolling is a Pareto improvement relative to the no-toll equilibrium. Those more productive users also suffer more in both no-toll equilibrium and optimal tolling, which indicates that a differentiated redistribution of toll revenues could be an incentive to improve productivity.

  16. Oil substitution and energy conservation in passenger transport - by the use of electric multiple units

    Energy Technology Data Exchange (ETDEWEB)

    Padiyar, K P

    1983-11-01

    India's National Transport Policy of accelerating the electrification of railways to a target of 1000 route kilometers per year and phasing out diesel engines is justified because of indigenous coal for power generation and the flexibility and better performance of electric equipment. This article examines the growth of passenger traffic and the corresponding decline in rail's share of that traffic since 1950 to illustrate the urgency of pursuing rail electrification. Traffic forecasts through the year 2000 emphasize that railway capacity is not keeping pace with demand, which results in discouraging public use. 8 tables. (DCK)

  17. Predictive NO x emission monitoring on board a passenger ferry

    Science.gov (United States)

    Cooper, D. A.; Andreasson, K.

    NO x emissions from a medium speed diesel engine on board a servicing passenger ferry have been indirectly measured using a predictive emission monitoring system (PEMS) over a 1-yr period. Conventional NO x measurements were carried out with a continuous emission monitoring system (CEMS) at the start of the study to provide historical data for the empirical PEMS function. On three other occasions during the year the CEMS was also used to verify the PEMS and follow any changes in emission signature of the engine. The PEMS consisted of monitoring exhaust O 2 concentrations (in situ electrochemical probe), engine load, combustion air temperature and humidity, and barometric pressure. Practical experiences with the PEMS equipment were positive and measurement data were transferred to a land-based office by using a modem data communication system. The initial PEMS function (PEMS1) gave systematic differences of 1.1-6.9% of the calibration domain (0-1725 ppm) and a relative accuracy of 6.7% when compared with CEMS for whole journeys and varying load situations. Further improvements on the performance could be obtained by updating this function. The calculated yearly emission for a total engine running time of 4618 h was 316 t NO x±38 t and the average NO x emission corrected for ambient conditions 14.3 g kWh corr-1. The exhaust profile of the engine in terms of NO x, CO and CO 2 emissions as determined by CEMS was similar for most of the year. Towards the end of the study period, a significantly lower NO x emission was detected which was probably caused by replacement of fuel injector nozzles. The study suggests that PEMS can be a viable option for continuous, long-term NO x measurements on board ships.

  18. Predictive NOx emission monitoring on board a passenger ferry

    International Nuclear Information System (INIS)

    Cooper, D.A.; Andreasson, K.

    1999-01-01

    NO x emissions from a medium speed diesel engine on board a servicing passenger ferry have been indirectly measured using a predictive emission monitoring system (PEMS) over a 1-yr period. Conventional NO x measurements were carried out with a continuous emission monitoring system (CEMS) at the start of the study to provide historical data for the empirical PEMS function. On three other occasions during the year the CEMS was also used to verify the PEMS and follow any changes in emission signature of the engine. The PEMS consisted of monitoring exhaust O 2 concentrations (in situ electrochemical probe), engine load, combustion air temperature and humidity, and barometric pressure. Practical experiences with the PEMS equipment were positive and measurement data were transferred to a land-based office by using a modem data communication system. The initial PEMS function (PEMS1) gave systematic differences of 1.1-6.9% of the calibration domain (0-1725 ppm) and a relative accuracy of 6.7% when compared with CEMS for whole journeys and varying load situations. Further improvements on the performance could be obtained by updating this function. The calculated yearly emission for a total engine running time of 4618 h was 316 t NO x ± 38 t and the average NO x emission corrected for ambient conditions 14.3 g kWh corr -1 . The exhaust profile of the engine in terms of NO x , CO and CO 2 emissions as determined by CEMS was similar for most of the year. Towards the end of the study period, a significantly lower NO x emission was detected which was probably caused by replacement of fuel injector nozzles. The study suggests that PEMS can be a viable option for continuous, long-term NO x measurements on board ships. (author)

  19. Convenient Airports: Point of View of the Passengers

    Science.gov (United States)

    Magri, Adival Aparecido, Jr.; Alves, Claudio Jorge Pinto

    2003-01-01

    The competition among airlines or among airports aiming at to increase the demand for its services has been more and more incited. Knowledge the perception of the users for the offered services means to meet the customer's needs and expectations in order either to keep the customer, and therefore keep a significant advantage over competitors. The passenger of the air transportation wants rapidity, security and convenience. Convenience can be translated by comfort that the passenger wants for the price that he can pay. In this paper had been identified. as a result of a survey achieved in six Brazilian airports during 2002, the best indicators in the passenger's perception. These indicators among any others were listed m the handbook of Airports Council International (ACI). Distinctive perceptions were observed among passengers with different travel motivations. This survey had been carried through in the airports of Brasilia, Porto Alegre, Salvador. Fortaleza, Curitiba and Bel6m. Considering this survey we can identified the most attractive airport among them. This work is a way to help improve quality of service, in particular, m these six airports of the Brazilian network. The results should be published and made available to all the parties concerned (airport authority, airlines and service providers) and should lead to corrective action when the passenger is not satisfied with the service.

  20. The impact of fiscal and other measures on new passenger car sales and CO2 emissions intensity. Evidence from Europe

    International Nuclear Information System (INIS)

    Ryan, Lisa; Convery, Frank; Ferreira, Susana

    2009-01-01

    This paper examines the impact of national fiscal measures in the EU (EU15) on passenger car sales and the CO 2 emissions intensity of the new car fleet over the period 1995-2004. CO 2 emissions and energy consumption from road transport have been increasing in the EU and as a result since 1999 the EU has attempted to implement a high profile policy strategy to address this problem at European level. Less prominent is the fact that Member States apply vehicle and fuel taxes, which may also be having an impact on the quantity of passenger cars sold and their CO 2 emissions intensity. Diesel vehicle sales have increased appreciably in many countries over the same period and this study makes a first attempt to examine whether Member State fiscal measures have influenced this phenomenon. This work uses a panel dataset to investigate the relationship between national vehicle and fuel taxes on new passenger car sales and the fleet CO 2 emissions intensity in EU15 over a 10-year period. Our results show that national vehicle and fuel taxes have had an impact on passenger car sales and fleet CO 2 emissions intensity and that different taxes have disparate effects. (author)

  1. Computable general equilibrium model fiscal year 2014 capability development report

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Brian Keith [Los Alamos National Laboratory; Boero, Riccardo [Los Alamos National Laboratory

    2016-05-11

    This report provides an overview of the development of the NISAC CGE economic modeling capability since 2012. This capability enhances NISAC's economic modeling and analysis capabilities to answer a broader set of questions than possible with previous economic analysis capability. In particular, CGE modeling captures how the different sectors of the economy, for example, households, businesses, government, etc., interact to allocate resources in an economy and this approach captures these interactions when it is used to estimate the economic impacts of the kinds of events NISAC often analyzes.

  2. FMCSA safety program effectiveness measurement: intervention model fiscal year 2009.

    Science.gov (United States)

    2013-04-01

    The Federal Motor Carrier Safety Administration (FMCSA), in cooperation with the researcher, has developed an analytic model to measure the effectiveness of roadside inspections and traffic enforcements in terms of crashes avoided, injuries avoided, ...

  3. Effect of Using Extreme Years in Hydrologic Model Calibration Performance

    Science.gov (United States)

    Goktas, R. K.; Tezel, U.; Kargi, P. G.; Ayvaz, T.; Tezyapar, I.; Mesta, B.; Kentel, E.

    2017-12-01

    Hydrological models are useful in predicting and developing management strategies for controlling the system behaviour. Specifically they can be used for evaluating streamflow at ungaged catchments, effect of climate change, best management practices on water resources, or identification of pollution sources in a watershed. This study is a part of a TUBITAK project named "Development of a geographical information system based decision-making tool for water quality management of Ergene Watershed using pollutant fingerprints". Within the scope of this project, first water resources in Ergene Watershed is studied. Streamgages found in the basin are identified and daily streamflow measurements are obtained from State Hydraulic Works of Turkey. Streamflow data is analysed using box-whisker plots, hydrographs and flow-duration curves focusing on identification of extreme periods, dry or wet. Then a hydrological model is developed for Ergene Watershed using HEC-HMS in the Watershed Modeling System (WMS) environment. The model is calibrated for various time periods including dry and wet ones and the performance of calibration is evaluated using Nash-Sutcliffe Efficiency (NSE), correlation coefficient, percent bias (PBIAS) and root mean square error. It is observed that calibration period affects the model performance, and the main purpose of the development of the hydrological model should guide calibration period selection. Acknowledgement: This study is funded by The Scientific and Technological Research Council of Turkey (TUBITAK) under Project Number 115Y064.

  4. Dynamics of Air Passenger Transportation in Eastern Romania

    Directory of Open Access Journals (Sweden)

    Dan Păuna

    2013-10-01

    Full Text Available The concept of an air route mile is, of course, entirely different from that of a road or rail route mile. An air route is a direct service between two cities. The too-rapid development of the air route system must inevitably result in an average intensity of operations on the route, and this means the frequencies are low or high, or the airplanes used are profitable or unprofitable. The purpose of this paper is to emphasize air passenger dynamics in Romania and to calculate specific indicators regarding this calculation for the airports in eastern Romania in 2011t., this, because the air passenger featurea indicator passenger – kilometer, starting with 2009 no longer calculate for aviation and shipping.

  5. Dynamic Pricing for Airline Revenue Management under Passenger Mental Accounting

    Directory of Open Access Journals (Sweden)

    Yusheng Hu

    2015-01-01

    Full Text Available Mental accounting is a far-reaching concept, which is often used to explain various kinds of irrational behaviors in human decision making process. This paper investigates dynamic pricing problems for single-flight and multiple flights settings, respectively, where passengers may be affected by mental accounting. We analyze dynamic pricing problems by means of the dynamic programming method and obtain the optimal pricing strategies. Further, we analytically show that the passenger mental accounting depth has a positive effect on the flight’s expected revenue for the single flight and numerically illustrate that the passenger mental accounting depth has a positive effect on the optimal prices for the multiple flights.

  6. Analysis of Seasonal Risk for Importation of the Mediterranean Fruit Fly, Ceratitis capitata (Diptera: Tephritidae), via Air Passenger Traffic Arriving in Florida and California.

    Science.gov (United States)

    Szyniszewska, A M; Leppla, N C; Huang, Z; Tatem, A J

    2016-12-01

    The Mediterranean fruit fly, Ceratitis capitata (Wiedemann), is one of the most economically damaging pests in the world and has repeatedly invaded two major agricultural states in the United States, Florida and California, each time requiring costly eradication. The Mediterranean fruit fly gains entry primarily in infested fruit carried by airline passengers and, since Florida and California each receive about 13 million international passengers annually, the risk of Mediterranean fruit fly entering the United States is potentially very high. The risk of passengers bringing the pest into Florida or California from Mediterranean fruit fly-infested countries was determined with two novel models, one estimated seasonal variation in airline passenger number and the other defined the seasonal and spatial variability in Mediterranean fruit fly abundance. These models elucidated relationships among the risk factors for Mediterranean fruit fly introduction, such as amount of passenger traffic, routes traveled, season of travel, abundance of Mediterranean fruit fly in countries where flights departed, and risk of the pest arriving at destination airports. The risk of Mediterranean fruit fly being introduced into Florida was greatest from Colombia, Brazil, Panama, Venezuela, Argentina, and Ecuador during January-August, whereas primarily the risk to California was from Brazil, Panama, Colombia, and Italy in May-August. About three times more Mediterranean fruit flies were intercepted in passenger baggage at airports in Florida than California, although the data were compromised by a lack of systematic sampling and other limitations. Nevertheless, this study achieved the goal of analyzing available data on seasonal passenger flow and Mediterranean fruit fly population levels to determine when surveillance should be intensified at key airports in Florida and California. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America

  7. Solid waste integrated cost analysis model: 1991 project year report

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    The purpose of the City of Houston's 1991 Solid Waste Integrated Cost Analysis Model (SWICAM) project was to continue the development of a computerized cost analysis model. This model is to provide solid waste managers with tool to evaluate the dollar cost of real or hypothetical solid waste management choices. Those choices have become complicated by the implementation of Subtitle D of the Resources Conservation and Recovery Act (RCRA) and the EPA's Integrated Approach to managing municipal solid waste;. that is, minimize generation, maximize recycling, reduce volume (incinerate), and then bury (landfill) only the remainder. Implementation of an integrated solid waste management system involving all or some of the options of recycling, waste to energy, composting, and landfilling is extremely complicated. Factors such as hauling distances, markets, and prices for recyclable, costs and benefits of transfer stations, and material recovery facilities must all be considered. A jurisdiction must determine the cost impacts of implementing a number of various possibilities for managing, handling, processing, and disposing of waste. SWICAM employs a single Lotus 123 spreadsheet to enable a jurisdiction to predict or assess the costs of its waste management system. It allows the user to select his own process flow for waste material and to manipulate the model to include as few or as many options as he or she chooses. The model will calculate the estimated cost for those choices selected. The user can then change the model to include or exclude waste stream components, until the mix of choices suits the user. Graphs can be produced as a visual communication aid in presenting the results of the cost analysis. SWICAM also allows future cost projections to be made.

  8. Changes in the Trade and Promotion of Passenger Air Transport

    Directory of Open Access Journals (Sweden)

    Cornelia Petroman

    2010-10-01

    Full Text Available Passenger air carriers will be able to systematically overbook transport capacities on certain aerial routes due to the quick adaptation to modern trading means, to the modern promotion of services and to the modern means of information of potential travellers. Though ticket booking in aerial transport made its debut as a simple process of automation of ticket sale, it soon turned into a strong marketing instrument with unexpected effects on competitiveness on the market of tourism aerial transport. The use of modern ways of operating Computer Reservation Systems and Billing Settlement Plans by passenger air companies and by tour operators improves service standards.

  9. Comparing data quality and cost from three modes of on-board transit passenger surveys.

    Science.gov (United States)

    2015-06-01

    This report presents the findings from a research project investigating the relative data quality and administration costs for three : different modes of surveying bus passengers that produce results generalizable to the full passenger population. Th...

  10. High Speed Vessels to Market : Comparative Case Studies in the Passenger Trade

    Science.gov (United States)

    2001-08-01

    The Volpe Center chose to study several existing catamarans and high speed monohulls in comparison to representative SWATH family craft, including the SLICE 400 (passenger) and SLICE 600 (passenger/90 car) variants, the former similar in size and per...

  11. Forecasting of passenger traffic in Moscow metro applying artificial neural networks

    International Nuclear Information System (INIS)

    Ivanov, V.V.; Natsional'nyj Issledovatel'skij Yadernyj Univ. MIFI, Moscow; FKU Rostransmodernizatsiya, Moscow

    2016-01-01

    Methods for the forecasting of passenger traffic in Moscow metro have been developed using artificial neural networks. To this end, the factors primarily determining passenger traffic in the subway have been analyzed and selected [ru

  12. Multiple imputation of missing passenger boarding data in the national census of ferry operators

    Science.gov (United States)

    2008-08-01

    This report presents findings from the 2006 National Census of Ferry Operators (NCFO) augmented with imputed values for passengers and passenger miles. Due to the imputation procedures used to calculate missing data, totals in Table 1 may not corresp...

  13. HRTPO strategic campaign and vision plan for passenger rail : phase 1 overview.

    Science.gov (United States)

    2010-03-17

    SUBJECT: : TEMS (Transportation Economics & Management Systems, Inc.), the consultant specializing in : passenger rail planning, was secured by the HRTPO and its partner DRPT to evaluate the potential : passenger rail service alternative defined by t...

  14. The early years of string theory: The dual resonance model

    International Nuclear Information System (INIS)

    Ramond, P.

    1987-10-01

    This paper reviews the past quantum mechanical history of the dual resonance model which is an early string theory. The content of this paper is listed as follows: historical review, the Veneziano amplitude, the operator formalism, the ghost story, and the string story

  15. The "Biopsychosocial Model": 40 years of application in Psychiatry.

    Science.gov (United States)

    Papadimitriou, G

    2017-01-01

    In 1977, the American pathologist and psychiatrist George Engel (1913-1999) published in the Journal Science his paper "TheIn 1977, the American pathologist and psychiatrist George Engel (1913-1999) published in the Journal Science his paper "Theneed for a new medical model: A challenge for biomedicine", introducing the term Biopsychosocial Model. This model basedon the results of Engel's studies in ulcerative colitis, depression and psychogenic pain, constituted a challenge for biomedicineand the biomedical model. The basic principles of the model included the biological, psychological and social dimensions of the person's life and theperception that the person suffers as a whole and not as isolated organs. The doctor should use a holistic approach regardingillness and should consider his/her relation with the patient socially equal. The personality and the emotional reserves of thepatient, as well as the particular environmental conditions in which the person lives in should be taken into account. There is no doubt that the biopsychosocial model has established a more empathetic and compassionate approach in medical practice. Already since 1936, the general adaptation syndrome had been proposed by the Austrian-Canadian endocrinologist HansSeley (1907-1982), who emphasized that psychological stressful factors may have injurious consequences on health, while theresponse systems to stress may be dysregulated not only by genetic factors, but also from experiences and stressful life events,as well as by harmful behaviors such as smoking, alcohol consumption and lack of physical exercise. Psychosocial factors may co-determine the patient's vulnerability and the illness's severity and course. The biopsychosocialmodel consider the interactions with genetic susceptibility, personality, stressful events and, generally, with the patient's socialcontext. Environmental factors increase the probability of the clinical expression of a mental disorder, play a role in the time

  16. Acoustic vocal tract model of one-year-old children

    OpenAIRE

    Vojnović, Milan; Bogavac, Ivana; Dobrijević, Ljiljana

    2014-01-01

    The physical shape of vocal tract and its formant (resonant) frequencies are directly related. The study of this functional connectivity is essential in speech therapy practice with children. Most of the perceived children’s speech anomalies can be explained on a physical level: malfunctioning movement of articulation organs. The current problem is that there is no enough data on the anatomical shape of children’s vocal tract to create its acoustic model. Classical techniques for vocal tract...

  17. Modelling loans and deposits during electoral years i n Romania

    Directory of Open Access Journals (Sweden)

    Nicolae - Marius JULA

    2015-06-01

    Full Text Available This paper analyzes the effect of electoral years on loans and deposits for population in Romania. Using monthly data regarding the total loans and deposits, we identify the significance of the electoral timing on population´s behavior regarding financial decisions. We estimate that there are small changes in population´s affinity for increase in the indebtedness or for savings. We use dummy variables for electoral periods, and when these are econometrically significant there is an evidence of the influence of the electoral timings in population´s financial decisions.

  18. Numerical modelling: where will we be in ten years

    International Nuclear Information System (INIS)

    Caseau, P.

    1993-01-01

    Computer hardware power is increasing following a regular curve since 30 years; the 2000-2005 horizon is easy to extrapolate. But interactions between machine capacity, processing speed, working memory and memory store, pre- and post-processing/stations capacity, process communications/stations capacity, etc. are more difficult to assess, such as the place of one-Teraflop machines in an architecture. The needs for an one Teraflop capacity for various applications are discussed: numerical simulation of diffusion and transport in neutronics, of poly-phasic and reactive flows, of large electric utility networks, of physico-chemistry at molecular levels; artificial intelligence may play a major role. 2 figs

  19. Radiation exposure of aircrew and passengers during some Czechoslovak airlines commercial flights

    International Nuclear Information System (INIS)

    Spurny, F.; Votockova, I.

    1994-01-01

    Radiation exposure of aircrew and passengers on boards of Czechoslovak Airlines (CSA) subsonic aircraft was studied. It was found that the exposure levels depends on flights altitude, changes also with geographical position (latitude and longitude). Measurements were performed during 1991 to 1993 years; i.e. at the period of sun maximum and immediately after it. Total dose equivalent rates did not exceed 10 μSv per hour of flight. An increasing of its level with decreasing sun activity has been already registered. (orig.)

  20. Delay-based Passenger Car Equivalent at Signalized Intersections in Iran

    Directory of Open Access Journals (Sweden)

    Habibollah Nassiri

    2017-04-01

    Full Text Available Due to their different sizes and operational characteristics, vehicles other than passenger cars have a different influence on traffic operations especially at intersections. The passenger car equivalent (PCE is the parameter that shows how many passenger cars must be substituted for a specific heavy vehicle to represent its influence on traffic operation. PCE is commonly estimated using headway-based methods that consider the excess headway utilized by heavy vehicles. In this research, the PCE was estimated based on the delay parameter at three signalized intersections in Tehran, Iran. The data collected were traffic volume, travel time for each movement, signalization, and geometric design information. These data were analysed and three different models, one for each intersection, were constructed and calibrated using TRAF-NETSIM simulation software for unsaturated traffic conditions. PCE was estimated under different scenarios and the number of approach movements at each intersection. The results showed that for approaches with only one movement, PCE varies from 1.1 to 1.65. Similarly, for approaches with two and three movements, the PCE varies from 1.07 to 1.99 and from 0.76 to 3.6, respectively. In addition, a general model was developed for predicting PCE for intersections with all of the movements considered. The results obtained from this model showed that the average PCE of 1.5 is similar to the value recommended by the HCM (Highway Capacity Manual 1985. However, the predicted PCE value of 1.9 for saturated threshold is closer to the PCE value of 2 which was recommended by the HCM 2000 and HCM 2010.

  1. Influence patterns of transportation parameters in suburban traffic on fatigue of passengers during bus waiting

    Directory of Open Access Journals (Sweden)

    Тетяна Михайлівна Григорова

    2015-05-01

    Full Text Available The change of transport fatigue of suburban traffic passengers during waiting transport waiting is investigated. The results of the processing site examinations allow defining the regularities of the influence of parameters of transportation process of passengers to change index activity of regulatory systems in passenger waiting at stopping points of suburban traffic. The discovered patterns were mathematically formalized

  2. 75 FR 16552 - High-Speed Intercity Passenger Rail (HSIPR) Program

    Science.gov (United States)

    2010-04-01

    ...; Enhancing intercity travel options; Ensuring a state of good repair of key intercity passenger rail assets... DEPARTMENT OF TRANSPORTATION Federal Railroad Administration High-Speed Intercity Passenger Rail... selections for the High-Speed Intercity Passenger Rail (HSIPR) Program. This notice builds on the program...

  3. 76 FR 5825 - U.S.-Korea Free Trade Agreement: Passenger Vehicle Sector Update

    Science.gov (United States)

    2011-02-02

    ...: Passenger Vehicle Sector Update AGENCY: United States International Trade Commission. ACTION: Institution of...) instituted investigation No. 332-523, U.S.-Korea Free Trade Agreement: Passenger Vehicle Sector Update. DATES... concluded negotiations to modify the FTA, including certain provisions relating to the passenger vehicle...

  4. 77 FR 24381 - Security Zone; Passenger Vessel SAFARI EXPLORER Arrival/Departure, Kaunakakai Harbor, Molokai, HI

    Science.gov (United States)

    2012-04-24

    ...-AA87 Security Zone; Passenger Vessel SAFARI EXPLORER Arrival/ Departure, Kaunakakai Harbor, Molokai, HI... channel's entrance during the arrival and departure of the Passenger Vessel Safari Explorer in Kaunakakai... entrance during the arrival and departure of the Passenger Vessel Safari Explorer in Kaunakakai Harbor...

  5. 46 CFR 25.45-2 - Cooking systems on vessels carrying passengers for hire.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Cooking systems on vessels carrying passengers for hire... REQUIREMENTS Cooking, Heating, and Lighting Systems § 25.45-2 Cooking systems on vessels carrying passengers for hire. (a) No fuel may be used in any cooking system on any vessel carrying passengers for hire...

  6. 49 CFR 223.17 - Identification of equipped locomotives, passenger cars and cabooses.

    Science.gov (United States)

    2010-10-01

    ... cars and cabooses. 223.17 Section 223.17 Transportation Other Regulations Relating to Transportation...-LOCOMOTIVES, PASSENGER CARS AND CABOOSES Specific Requirements § 223.17 Identification of equipped locomotives, passenger cars and cabooses. Each locomotive, passenger car and caboose that is fully equipped with glazing...

  7. 49 CFR 583.10 - Outside suppliers of passenger motor vehicle equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Outside suppliers of passenger motor vehicle... CONTENT LABELING § 583.10 Outside suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment for which a manufacturer or allied supplier requests information...

  8. 36 CFR 1005.4 - Commercial passenger-carrying motor vehicles.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Commercial passenger-carrying motor vehicles. 1005.4 Section 1005.4 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.4 Commercial passenger-carrying motor vehicles. Passenger-carrying motor...

  9. 36 CFR 13.1316 - Commercial transport of passengers by motor vehicles.

    Science.gov (United States)

    2010-07-01

    ... passengers by motor vehicles. 13.1316 Section 13.1316 Parks, Forests, and Public Property NATIONAL PARK... National Park General Provisions § 13.1316 Commercial transport of passengers by motor vehicles. Commercial transport of passengers by motor vehicles on Exit Glacier Road is allowed without a written permit. However...

  10. 49 CFR 583.11 - Allied suppliers of passenger motor vehicle equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Allied suppliers of passenger motor vehicle... CONTENT LABELING § 583.11 Allied suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment which an allied supplier supplies to the manufacturer with which...

  11. 78 FR 51812 - Urbanized Area Formula Grants; Passenger Ferry Grant Program

    Science.gov (United States)

    2013-08-21

    ... authorized by the Moving Ahead for Progress in the 21st Century Act (MAP-21), Public Law 112- 141, July 6... accommodate walk-on passengers. 2. Eligible Projects Under this competitive program, eligible projects are... the number of trips (passengers and vehicles), the number of walk-on passengers, and transfers to...

  12. Natural gas passenger vehicles: challenges and way forward

    International Nuclear Information System (INIS)

    Sahari, B. B.; Hamouda, A. M. S.

    2006-01-01

    Natural gas vehicles have been used in the world for many years: at present, there are about 3 million vehicles running on natural gas and many governments and vehicle manufactures are involved in programs for further developing the market for natural gas vehicles. In comparison to other forms of energy for vehicles, natural gas (NG) engenders low pressures on the environment. At the same time, because of its technical characteristics, NG is very suitable for motor use. The economic advantage of converting a vehicles (NGVs) would be expected to attract the interest of a great number of people, and achieve rapid and widespread diffusion. On the contrary, traditional fuels still dominate the scene, and show no sign of going out of fashion. The use of natural gas as automotive fuel has become of national and worldwide interests particularly so with the recent increase in petrol price, depleting petrol reserves and stringent control of exhaust emission levels. For automotive applications, shifting from petrol to gas needs technological research and development. Within the framework of the reciprocating piston based engine this development is very challenging with technological issues of low range, refueling infrastructure, heavy fuel storage, safety, emissions control and gas operating pressures. Other issues include available expertise and experience in research management. This paper describes the advances being made with passenger vehicles natural gas engines worldwide and in Malaysia more specific. The significant milestones in the development of NGV in Malaysia and the rationale behind the choice of NGV industry including the NGV vehicle population growth, the development of service station as well as the expansion of the sales volume will be illustrated. The presentation presents also development stages and advances in development, fabrication and testing a Compressed Natural Gas Direct Injection vehicle and NGV refueling station. This presentation discuses the

  13. Media mix elements affecting brand equity: A study of the Indian passenger car market

    Directory of Open Access Journals (Sweden)

    Tanmay Chattopadhyay

    2010-12-01

    Full Text Available The study develops and empirically tests a model for finding the effect of advertising frequency across different media vehicles towards building brand equity for the passenger car market for first time and repeat buyers. The effect that selected media mix elements had on the dimensions of brand equity was examined. First time buyers are expected to have lower category knowledge than repeat buyers, and are hence expected to behave differently from repeat buyers. Since the knowledge structures of these two groups are expected to be different, it is reasonable to predict that they would process product/brand related information differently and this is corroborated by the results.

  14. Pittsburgh International Airport - Scheduled Passenger Traffic

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — Here you can find Pittsburgh International Airport’s Monthly Scheduled Traffic Reports. Each of these reports contain a year-over-year (YOY) analysis of scheduled...

  15. Bridge Condition Assessment based on Vibration Responses of Passenger Vehicle

    International Nuclear Information System (INIS)

    Miyamoto, Ayaho; Yabe, Akito

    2011-01-01

    In this paper, we propose a new method of assessing the condition of existing short- and medium-span reinforced/prestressed concrete bridges based on vibration monitoring data obtained from a public bus. This paper not only describes details of a prototype monitoring system that uses information technology and sensors capable of providing more accurate knowledge of bridge performance than conventional ways but also shows a few specific examples of bridge condition assessment based on vehicle vibrations measured by using an in-service public bus equipped with vibration measurement instrumentation. This paper also describes a sensitivity analysis of deteriorating bridges based on simulation of the acceleration response of buses conducted by the 'substructure method' employing a finite element model to verify the above bridge performance results. The main conclusions obtained in this study can be summarized as follows: (1) Because the vibration responses of passenger vehicles, such as buses, have a good linear relationship with the vibration responses of the target bridges, the proposed system can be used as a practical monitoring system for bridge condition assessment. (2) The results of sensitivity analysis performed by the substructure method show that bus vibration responses are useful for evaluating target bridge performance. (3) The proposed method was applied to a network of real bridges in a local area to evaluate its effectiveness. The results indicate that the proposed method can be used to prioritize the repair/strengthening works of existing bridges based on various vibration information in order to help bridge administrators establish rational maintenance strategies.

  16. Violence Against Drivers and Conductors in the Road Passenger ...

    African Journals Online (AJOL)

    This cross-sectional study examined the extent, nature and risk factors of workplace violence in the road passenger transport sector in Maputo, the capital city of Mozambique. A random sample of 504 participants was selected from a population of 2 618 registered bus, minibus, and taxi drivers/conductors. The results ...

  17. 76 FR 55335 - Alternate Passenger Rail Service Pilot Program

    Science.gov (United States)

    2011-09-07

    ... provides that the proposed pilot program would not be made available to more than two Amtrak intercity... operation; provisions for accommodating the traveling public, including proposed arrangements for stations... program developed by this part will not be made available to more than two Amtrak intercity passenger rail...

  18. EVs and post 2020 CO2 targets for passenger cars

    NARCIS (Netherlands)

    Smokers, R.T.M.; Verbeek, M.; Zyl, S. van

    2013-01-01

    This paper analyses what post 2020 targets may be necessary for the European CO2 legislation for passenger cars in order to reach the overall sectoral goal of 60% reduction of transport's greenhouse gas emissions by 2050 relative to 1990, as defined in the European Commission's White Paper. The

  19. Consumer preferences in the design of airport passenger areas

    NARCIS (Netherlands)

    Van Oel, C.J.; Van den Berkhof, F.W.

    2013-01-01

    In recent decades, commercial developments have become increasingly important for the overall profit of airports. However, little is known about consumer preferences regarding the design of passenger areas, which is striking as the design of terminal buildings affects consumers' emotional state and

  20. Alignment analysis of urban railways based on passenger travel demand

    DEFF Research Database (Denmark)

    Andersen, Jonas Lohmann Elkjær; Landex, Alex

    2010-01-01

    Planning of urban railways like Metro and especially Light Rail Transit often result in multiple alignment alternatives from where it can be difficult to select the best one. Travel demand is a good foundation for evaluating a railway alignment for its ability to attract passengers. Therefore...... and can be applied as decision support in different stages of the urban railway alignment planning....

  1. Trends in passenger transport energy use in South Korea

    International Nuclear Information System (INIS)

    Eom, Jiyong; Schipper, Lee

    2010-01-01

    Having a clear understanding of transport energy use trends is crucial to identifying opportunities and challenges for efficient energy use for the transport sector. To this date, however, no detailed analysis has been conducted with regard to rapidly growing passenger transport energy use in South Korea. Using bottom-up data developed from a variety of recent sources, we described the trends of transport activity, energy use, and CO 2 emissions from South Korea's transport sector since 1986 with a particular focus on its passenger transport. By decomposing the trends in passenger transport energy use into activity, modal structure, and energy intensity, we showed that while travel activity has been the major driver of the increase in passenger transport energy use in South Korea, the increase was to some extent offset by the recent favorable structural shift toward bus travel and away from car travel. We also demonstrated that while bus travel has become less energy intensive since the Asian Financial Crisis, car travel has become increasingly energy intensive.

  2. Passenger Transportation and Travel Curriculum Guide. Final Report.

    Science.gov (United States)

    Lininger, Carol

    This curriculum guide provides materials for a course in passenger transportation and travel. The four-credit, competency-based program provides students with skills necessary to obtain employment in the aviation industry, travel agencies, hotel/motel management, and car rental agencies. An overview of vocational-technical education at the school…

  3. Emergency evacuation : how better interior design can improve passenger flow

    NARCIS (Netherlands)

    Boer, L.C.; Skjong, R.

    2001-01-01

    The paper presents some conclusions from the EU basic research project "MEPdesign" relevant for design of ship interiors. The findings are discussed with regard to passenger flow as a function of design parameters. The paper explains that current evacuation analyses may be overly optimistic. The

  4. Factor Analysis of Passenger Cars Using as a Taxi

    Directory of Open Access Journals (Sweden)

    Deriugin O.V.

    2016-05-01

    Full Text Available A procedure to select passenger cars has been proposed. The procedure helps substantiate choice of effective transportation means in accordance with taxi class to meet consumption requirements of those taking part in transportation process from the viewpoint of comfort, safety, and minimum expenditures in the context of such transportation type.

  5. Chicago to Iowa City intercity passenger rail route : business plan.

    Science.gov (United States)

    2011-03-21

    This business plan describes the methods by which the Iowa Department of Transportation (DOT will partner with Iowa counties and cities to fund Iowas share of the operating and maintenance cost for the Chicago-Iowa City passenger-rail service, an ...

  6. Maintenance in Railway Rolling Stock Rescheduling for Passenger Railways

    NARCIS (Netherlands)

    J.C. Wagenaar (Joris); L.G. Kroon (Leo)

    2015-01-01

    textabstractThis paper addresses the Rolling Stock Rescheduling Problem (RSRP), while taking maintenance appointments into account. After a disruption, the rolling stock of passenger trains has to be rescheduled in order to maintain a feasible rolling stock circulation. A limited number of rolling

  7. Choosing the tariff for city passenger transportation in Kiev

    OpenAIRE

    Pilipenko, N.

    2006-01-01

    This article deals with basic problems of tariff policy of city passenger transportations by busses fleets of communal pattern ownership in Kiev. Principles of perfection of method of calculation of tariffs have been offered by introduction of rout and unique tariff.

  8. Causal analysis of passenger train accidents on freight rail corridors.

    Science.gov (United States)

    2013-11-01

    A number of economic, technical and political factors have limited the development of new, dedicated, very-high-speed rail systems in North America. Consequently, most, near-term development of improved or expanded passenger rail service in the U.S. ...

  9. Ultrafine particle air pollution inside diesel-propelled passenger trains.

    Science.gov (United States)

    Abramesko, Victoria; Tartakovsky, Leonid

    2017-07-01

    Locomotives with diesel engines are used worldwide and are an important source of air pollution. Pollutant emissions by locomotive engines affect the air quality inside passenger trains. This study is aimed at investigating ultrafine particle (UFP) air pollution inside passenger trains and providing a basis for assessing passenger exposure to this pollutant. The concentrations of UFPs inside the carriages of push-pull trains are dramatically higher when the train operates in pull mode. This clearly shows that locomotive engine emissions are a dominant factor in train passengers' exposure to UFPs. The highest levels of UFP air pollution are observed inside the carriages of pull trains close to the locomotive. In push mode, the UFP number concentrations were lower by factors of 2.6-43 (depending on the carriage type) compared to pull mode. The UFP concentrations are substantially lower in diesel multiple-unit trains than in trains operating in pull mode. A significant influence of the train movement regime on the UFP NC inside a carriage is observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. 31 CFR 515.569 - Foreign passengers' baggage.

    Science.gov (United States)

    2010-07-01

    ..., Authorizations, and Statements of Licensing Policy § 515.569 Foreign passengers' baggage. The importation of Cuban-origin goods, otherwise prohibited by this part, brought into the United States as baggage by any person arriving in the United States other than a citizen or resident of the United States is hereby...

  11. 76 FR 41726 - Reporting Ancillary Airline Passenger Revenues

    Science.gov (United States)

    2011-07-15

    ...., third checked bag or more) Overweight/Oversized Baggage/Sports Equipment Carry-On Baggage 4. In-Flight Medical Equipment 5. In-Flight Entertainment/Internet Access 6. Sleep Sets 7. In-Flight Food/Non Alcoholic... baggage performance is outdated. Airline passengers would [[Page 41728

  12. APPLICATION OF NFC TECHNOLOGY IN PASSENGER RAIL TRANSPORT

    Directory of Open Access Journals (Sweden)

    Henryk KOMSTA

    2016-09-01

    Full Text Available The article discusses the possibility of the application of the NFC technology as a system of selling tickets in passenger rail transport. The NFC (Near Field Communication technology is a wireless and contactless technology of transmission of radio data over short distances (max. 5 cm. This technology is very similar to the RFID (Radio Frequency Identification technology. It is assumed that this technology will spread rapidly and that already in 2015 around 85% of the payments in the EU will be made via mobile phones. This paper presents a research of passenger interest in this method of payment for tickets in the passenger rail transport in Slovakia. Further, an analysis of the applications of the NFC technology as a system of selling tickets in passenger rail transport, including the protection of data in mobile phones, the processes in case of losing a mobile phone and ensuring the communication between both parties was presented in the article. The last part of this analysis shows the possibility of purchasing tickets regardless of the carrier and the transport type.

  13. GEM1: First-year modeling and IT activities for the Global Earthquake Model

    Science.gov (United States)

    Anderson, G.; Giardini, D.; Wiemer, S.

    2009-04-01

    GEM is a public-private partnership initiated by the Organisation for Economic Cooperation and Development (OECD) to build an independent standard for modeling and communicating earthquake risk worldwide. GEM is aimed at providing authoritative, open information about seismic risk and decision tools to support mitigation. GEM will also raise risk awareness and help post-disaster economic development, with the ultimate goal of reducing the toll of future earthquakes. GEM will provide a unified set of seismic hazard, risk, and loss modeling tools based on a common global IT infrastructure and consensus standards. These tools, systems, and standards will be developed in partnership with organizations around the world, with coordination by the GEM Secretariat and its Secretary General. GEM partners will develop a variety of global components, including a unified earthquake catalog, fault database, and ground motion prediction equations. To ensure broad representation and community acceptance, GEM will include local knowledge in all modeling activities, incorporate existing detailed models where possible, and independently test all resulting tools and models. When completed in five years, GEM will have a versatile, penly accessible modeling environment that can be updated as necessary, and will provide the global standard for seismic hazard, risk, and loss models to government ministers, scientists and engineers, financial institutions, and the public worldwide. GEM is now underway with key support provided by private sponsors (Munich Reinsurance Company, Zurich Financial Services, AIR Worldwide Corporation, and Willis Group Holdings); countries including Belgium, Germany, Italy, Singapore, Switzerland, and Turkey; and groups such as the European Commission. The GEM Secretariat has been selected by the OECD and will be hosted at the Eucentre at the University of Pavia in Italy; the Secretariat is now formalizing the creation of the GEM Foundation. Some of GEM's global

  14. Passenger train emergency systems : development of prototype railEXODUS software for U.S. passenger rail car egress.

    Science.gov (United States)

    2014-11-01

    The Federal Railroad Administration (FRA), U.S. Department of Transportation (U.S. DOT), is sponsoring a research program, which includes investigation of the applicability of time-based egress performance requirements to U.S. passenger rail cars. Th...

  15. The Impact of Intelligent Transportation System Implementations on the Sustainable Growth of Passenger Transport in EU Regions

    Directory of Open Access Journals (Sweden)

    Ewa Stawiarska

    2018-04-01

    Full Text Available This article discusses original studies that demonstrate the relation between developed elements of the transportation network (road system density; railway system density; number of regional railway and bus connections, length of regional railway and bus connections, online accessibility to transportation services and other services related to the development of IT techniques to benefit mass transit and the regional GNP. A new development relative to preceding studies (as quoted is that the correlation coefficients calculated do not indicate any essential interrelations between elements of the transport system, or even the number of regional passenger transport services and regional GNP. A determination of the remaining data interrelations indicated the elements of the network which are considered essential to the development of mass transit, as resulting from a study carried out for the first time in 2015 for the Górnośląska-Zagłębioska Metropolis. Considering the fact that the number of railway connections has proven to be the most important determinant of the overall number of passenger transport services, the second part of the article presents studies that focus on the modeling of the railway network, applying the graph theory (extensively applied for ITS. Selected optimized models were analyzed and assessed in terms of possible implementability of specific improvements and the resultant growth in the number of passenger transport services. The research method applied was not novel, but the conclusions drawn from it were surprising, as they indicated that an optimized network of railway connections would not cause any significant increase in the number of passenger transport services. Successive surveys (supplementing statistical analyses have confirmed the importance of ITS in increasing the share of mass transit in overall transit. (1 The study was carried out in Polish regions, with particular emphasis on Silesia. (2 Its

  16. Analysis of crashes using FE vehicle models. Relations between vehicle types and crash characteristics; Yugen yoso model wo mochiita sharyo no shototsu kaiseki. Sharyo type to shototsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Takatori, O. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

    2000-01-01

    The objective of this study is to analyze the crash characteristics of vehicles under the condition of real-world accidents. This paper pays attention to the differences in the crash characteristics of a vehicle colliding with a vehicle which is a different type. Vehicles on the market can be divided broadly into two vehicle structures, monocoque structure and frame structure. Monocoque structure is mainly used for passenger vehicles and frame structure is for recreational vehicles (RV). In recent years, RV has been a large seller on the market. So accidents between passenger vehicles and a RVs occur frequently. The analysis of experimental data and computer simulation, which is predicated on the experimental data, was carried out for this study. In the analysis of experimental data, barrier force data from the New Car Assessment Program (NCAP) were analyzed. The FE passenger vehicle model which is based on systematic validation tests was used for the computer simulation of car-to-car collisions. (author)

  17. Rural and Urban Differences in Passenger-Vehicle-Occupant Deaths and Seat Belt Use Among Adults - United States, 2014.

    Science.gov (United States)

    Beck, Laurie F; Downs, Jonathan; Stevens, Mark R; Sauber-Schatz, Erin K

    2017-09-22

    Motor-vehicle crashes are a leading cause of death in the United States. Compared with urban residents, rural residents are at an increased risk for death from crashes and are less likely to wear seat belts. These differences have not been well described by levels of rurality. 2014. Data from the Fatality Analysis Reporting System (FARS) and the Behavioral Risk Factor Surveillance System (BRFSS) were used to identify passenger-vehicle-occupant deaths from motor-vehicle crashes and estimate the prevalence of seat belt use. FARS, a census of U.S. motor-vehicle crashes involving one or more deaths, was used to identify passenger-vehicle-occupant deaths among adults aged ≥18 years. Passenger-vehicle occupants were defined as persons driving or riding in passenger cars, light trucks, vans, or sport utility vehicles. Death rates per 100,000 population, age-adjusted to the 2000 U.S. standard population and the proportion of occupants who were unrestrained at the time of the fatal crash, were calculated. BRFSS, an annual, state-based, random-digit-dialed telephone survey of the noninstitutionalized U.S. civilian population aged ≥18 years, was used to estimate prevalence of seat belt use. FARS and BRFSS data were analyzed by a six-level rural-urban designation, based on the U.S. Department of Agriculture 2013 rural-urban continuum codes, and stratified by census region and type of state seat belt enforcement law (primary or secondary). Within each census region, age-adjusted passenger-vehicle-occupant death rates per 100,000 population increased with increasing rurality, from the most urban to the most rural counties: South, 6.8 to 29.2; Midwest, 5.3 to 25.8; West, 3.9 to 40.0; and Northeast, 3.5 to 10.8. (For the Northeast, data for the most rural counties were not reported because of suppression criteria; comparison is for the most urban to the second-most rural counties.) Similarly, the proportion of occupants who were unrestrained at the time of the fatal crash

  18. Lethal pedestrian--passenger car collisions in Berlin. Changed injury patterns in two different time intervals.

    Science.gov (United States)

    Ehrlich, Edwin; Tischer, Anja; Maxeiner, H

    2009-04-01

    To expand the passive safety of automobiles protecting traffic participants technological innovations were done in the last decades. Objective of our retrospective analysis was to examine if these technical modifications led to a clearly changed pattern of injuries of pedestrians whose death was caused by the accidents. Another reduction concerns the exclusion of injured car passengers--only pedestrians walking or standing at the moment of collision were included. We selected time intervals 1975-1985 and 1991-2004 (=years of construction of the involved passenger cars). The cars were classified depending on their frontal construction in types as presented by Schindler et al. [Schindler V, Kühn M, Weber S, Siegler H, Heinrich T. Verletzungsmechanismen und Wirkabschätzungen der Fahrzegfrontgestaltung bei Pkw-Fussgänger-Kollisionen. Abschlussbericht im Auftrag der Deutschen Versicherungswirtschaft e.V. TU-Berlin Fachgebiet Kraftfahrzeuge (GDV) 2004:36-40]. In both periods more than 90% of all cars were from the usual types small/medium/large class. Hundred and thirty-four autopsy records of such cases from Department of Forensic Medicine (Charité Berlin) data were analysed. The data included technical information of the accidents and vehicles and the external and internal injuries of the victims. The comparison of the two periods showed a decrease of serious head injuries and femoral fractures but an increase of chest-, abdominal and pelvic injuries. This situation could be explained by an increased occurrence of soft-face-constructions and changed front design of modern passenger cars, resulting in a favourable effects concerning head impact to the car during accident. Otherwise the same kinetic energy was transferred to the (complete) victim - but because of a displacement of main focus of impact the pattern of injuries modified (went distally).

  19. FMCSA safety program effectiveness measurement : Intervention Model in fiscal year 2007

    Science.gov (United States)

    2011-04-01

    This report presents results from FMCSAs Roadside Intervention Model for fiscal year 2007. The model estimates the number of crashes avoided, as well as injuries avoided and lives saved, as a result of the Agencys roadside inspection program. T...

  20. Dangers on the road: A longitudinal examination of passenger-initiated violence against bus drivers.

    Science.gov (United States)

    Zhou, Biru; Boyer, Richard; Guay, Stéphane

    2018-04-01

    This study examined the impact of workplace violence against 109 bus drivers over a 1-year span. Workplace violence is related to both psychological and work-related consequences. Our findings showed that bus drivers experienced a wide range of violence at work and the psychological consequences were devastating: Half of the participants met the diagnostic criteria for acute stress disorder within the first month following the index event. Majority of them experienced at least moderate levels of post-traumatic stress disorder (PTSD) problems over the 1-year span. About 9.3% of participants showed a delayed onset of PTSD 6 months after. Furthermore, counter-supportive behaviours and reexposure to violence played important roles in the maintenance of PTSD symptoms over time. Even though PTSD symptoms per se did not relate to bus driver's confidence in coping with aggressive passengers, the immediate post-traumatic reaction-symptoms of acute stress disorder-showed a significant long-term negative effect on bus drivers' confidence in dealing with aggressive passengers 12 months after. This study provided empirical evidence of the changing nature of PTSD symptoms over time among bus drivers. Copyright © 2017 John Wiley & Sons, Ltd.

  1. Emission characteristics when using bioethanol as a fuel for passenger cars

    International Nuclear Information System (INIS)

    Egebaeck, K.E.; Laurikko, J.; Ryden, C.

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm's Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV's and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  2. Emission characteristics when using bioethanol as a fuel for passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K.E. [Luleaa Univ. of Technology, (Sweden); Laurikko, J. [Technical Research Centre of Finland, Helsinki (Finland); Ryden, C. [Tima, (Sweden)

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm`s Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV`s and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  3. Modelling and hardware-in-the-loop simulation of the blowout tract components for passenger compartment air conditioning of motor vehicles; Modellierung und Hardware-in-the-Loop-Simulation der Komponenten des Ausblastraktes zur Kraftfahrzeuginnenraumklimatisierung

    Energy Technology Data Exchange (ETDEWEB)

    Michalek, David

    2009-07-01

    The author investigated the modelling and hardware-in-the-loop simulation of components of the blowout tract of motor car air conditioning systems. The control systems and air conditioning systems are gone into, from the air entering the car to the control systems and sensors for monitoring state variables. The function of the control equipment hardware and software was to be analyzed reproducibly in order to save time and cost. The models were verified using available data. Validation criteria were established for the hardware-in-the-loop simulator. On the basis of selected operating conditions, the performance of the air conditioning control unit inside the vehicle was compared with the simulation results and was evaluated on the basis of the established criteria. (orig.)

  4. 14 CFR 382.133 - What are the requirements concerning the evaluation and use of passenger-supplied electronic...

    Science.gov (United States)

    2010-01-01

    ... evaluation and use of passenger-supplied electronic devices that assist passengers with respiration in the... What are the requirements concerning the evaluation and use of passenger-supplied electronic devices... to use in the passenger cabin during air transportation, a ventilator, respirator, continuous...

  5. Evaluation of a New Strategy for Attending Takeoffs and Landings to Reduce Aircraft Operating Costs and Passenger Delays at the Mexico City International Airport

    Directory of Open Access Journals (Sweden)

    Herrera-García Alfonso

    2014-01-01

    Full Text Available The objective of this research was to evaluate a strategy for attending the takeoffs and landings at a congested airport, in order to reduce aircraft operating costs and passenger delay times. The continuous growth of air transport activity has created congestion at major airports worldwide, this situation produces increases in the aircraft operating costs and passenger discomfort. In the strategy evaluated the traditional rule for attending to aircraft, on a first-come-first-served basis, was substituted with a sequence that reduces operating costs and passenger delays. In order to perform this evaluation a discrete-event simulation model was developed for the Mexico City International Airport. Results showed that it is possible to obtain significant benefits if the proposed strategy is applied, an annual benefit of around 28.6 million pesos could be achieved.

  6. Investigation of Gas Piston Actuated Opening-Closing Trunk Lid Mechanisms Used in Passenger Cars

    Directory of Open Access Journals (Sweden)

    Ahmet YILDIZ

    2015-05-01

    Full Text Available In this study, the gas piston actuated opening-closing trunk lid mechanisms used in passenger cars are investigated theoretically and experimentally. First, the position analysis of the mechanism which is a four-bar linkage has been carried out. Then the quasi-static analyzes according to the principle of virtual work have been made, and so the hand force, one of the most important parameters in terms of ergonomics, required for opening and closing the trunk lid has been calculated. In order to verify this developed model, the hand force has been determined also experimentally, performing the physical tests on an existing vehicle at Turkish Automobile Factory Inc. (TOFAŞ. Eventually, it is observed that the results obtained from mathematical model and the experimental measurements are compatible each other. This established model will provide convenience for manufacturers to determine the hand force for different model of vehicles. 

  7. Predicting Graduation Rates at 4-Year Broad Access Institutions Using a Bayesian Modeling Approach

    Science.gov (United States)

    Crisp, Gloria; Doran, Erin; Salis Reyes, Nicole A.

    2018-01-01

    This study models graduation rates at 4-year broad access institutions (BAIs). We examine the student body, structural-demographic, and financial characteristics that best predict 6-year graduation rates across two time periods (2008-2009 and 2014-2015). A Bayesian model averaging approach is utilized to account for uncertainty in variable…

  8. CONCERNING THE PROBLEM OF SEMANTIC CONTRADICTIONS ARISING WHEN USING THE TERMS “INTERMODAL” AND “MULTIMODAL” PASSENGER CARRIAGES

    Directory of Open Access Journals (Sweden)

    Norayr Oganesovich Bludyan

    2017-05-01

    Full Text Available This article examines Russian and foreign regulatory documents, concerning the issues of intermodal/multimodal passenger carriages, shows the essence of intermodal transportation in passenger transport, includes the analysis of various approaches to the concepts of “intermodal passenger transportations” and “multimodal passenger transportations” and contains proposals for legislative consolidation of the mentioned terms and for the implementation of intermodal technologies in passenger transport.

  9. International foodborne outbreak of Shigella sonnei infection in airline passengers.

    Science.gov (United States)

    Gaynor, K; Park, S Y; Kanenaka, R; Colindres, R; Mintz, E; Ram, P K; Kitsutani, P; Nakata, M; Wedel, S; Boxrud, D; Jennings, D; Yoshida, H; Tosaka, N; He, H; Ching-Lee, M; Effler, P V

    2009-03-01

    During 22-24 August 2004, an outbreak of Shigella sonnei infection affected air travellers who departed from Hawaii. Forty-seven passengers with culture-confirmed shigellosis and 116 probable cases who travelled on 12 flights dispersed to Japan, Australia, 22 US states, and American Samoa. All flights were served by one caterer. Pulsed-field gel electrophoresis of all 29 S. sonnei isolates yielded patterns that matched within one band. Food histories and menu reviews identified raw carrot served onboard as the likely vehicle of infection. Attack rates for diarrhoea on three surveyed flights with confirmed cases were 54% (110/204), 32% (20/63), and 12% (8/67). A total of 2700 meals were served on flights with confirmed cases; using attack rates observed on surveyed flights, we estimated that 300-1500 passengers were infected. This outbreak illustrates the risk of rapid, global spread of illness from a point-source at a major airline hub.

  10. Passenger head in impact with frontal airbag in OOP postures

    Science.gov (United States)

    Ovidiu Soica, Adrian; Toganel, George-Radu

    2017-10-01

    Road accidents represent an aspect of road traffic that may lead negative consequences. In order to solve the problems associated with such events, interdisciplinary knowledge is called for, complex teams of engineers, doctors, lawyers, experts working together in order to reduce the severity of such events. Road safety is a continuous concern for both experts and various government organizations with the aim of protecting the lives of the participants in traffic. It has been estimated that the costs of traffic accidents account for 1-3% of a country GDP, depending on the level of country development [26]. In this paper we analyze a particular class of cases of injuries caused to passengers caused by the inflation of the frontal airbag when they are with the passenger out of position. Head kinematics, accelerations, as well as the severity of injuries expressed by HIC, as related to the AIS scale have been analysed.

  11. Toward a Shared Urban Transport System Ensuring Passengers & Goods Cohabitation

    Directory of Open Access Journals (Sweden)

    Anna Trentini

    2010-07-01

    Full Text Available The paper presents radical new urban transportation system concepts, potentially allowing changing the economic and environmental costs of passenger and freight transportation. The driver focuses on the concept of sharing, which means to make a joint use of transport resources, between passengers and goods flows. From a field observation of several existing solutions, an inductive reasoning enables us to move from a set of specific facts to establish an archetype for a radical new urban transportation system. Once the archetype defined, it is translated in real life through the example of the On Route proposal for London. The research frame of this paper is the ANR C-Goods (City Goods Operation Optimization using Decision support System project. Started in February 2009 the project involves four partners , and will end on 2011.

  12. Understanding Weight Management Perceptions in First-Year College Students Using the Health Belief Model

    Science.gov (United States)

    Das, Bhibha M.; Evans, Ellen M.

    2014-01-01

    Objective: To examine weight management barriers, using the Health Belief Model, in first-year college students. Participants: First-year college students (n = 45), with data collected in April, May, and November 2013. Methods: Nominal group technique sessions (n = 8) were conducted. Results: First-year students recognize benefits to weight…

  13. Intercity passenger transportation: energy efficiency and conservation case study

    Energy Technology Data Exchange (ETDEWEB)

    Khan, A.M.

    1981-01-01

    To demonstrate a methodology for energy analysis and to advance technical knowledge on the energy conservation potential in intercity passenger transportation, this paper reports findings of a case study of the Toronto-Ottawa-Montreal multimodal system. From a total (direct and indirect) energy perspective for origin-destination travel, energy efficiency and conservation potential of technological improvements, modal shifts and increased load factors are reported. 11 refs.

  14. Small passenger car transmission test; Chevrolet LUV transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    A 1978 Chevrolet LUV manual transmission tested per the applicable portions of a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the upper ninety percent range for both drive performance tests and coast performance tests. The major results of this test (torque, speed, and efficiency curves) are presented. Graphs map the complete performance characteristics for the Chevrolet LUV transmission.

  15. Materials for fire resistant passenger seats in aircraft

    Science.gov (United States)

    Tesoro, G.; Moussa, A.

    1980-01-01

    The paper considers the selection of cushioning foam and upholstery fabric materials for aircraft passenger seats. Polyurethane, polychloroprene, polyimide, and polyphosphazene are the foam materials considered; and a variety of commercial and developmental fabrics (including wool, cotton, synthetics, and blends) are examined. Viable approaches to the design of fire-resistant seat assemblies are indicated. Results of an experimental laboratory study of fabrics and fabric/foam assemblies exposed to external point-source radiative heat flux are discussed.

  16. Evaluating efficiency of passenger railway stations: a DEA approach

    OpenAIRE

    Khadem Sameni, Melody; Preston, John; Khadem Sameni, Mona

    2016-01-01

    Stations are bottlenecks for railway transportation as they are where traffics merge and diverge. Numerous activities such as passengers boarding, alighting and interchanging, train formation and technical checks are also done at these points. The number of platforms is limited and it is vital to do all the work efficiently. For the first time in the literature, we implement a methodology based on data envelopment analysis which is benchmarked from ports and airport efficiency studies. It can...

  17. A Numerical Study on Rear-spoiler of Passenger Vehicle

    OpenAIRE

    Xu-xia Hu; Eric T. T. Wong

    2011-01-01

    The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoi...

  18. Development Of Fiber Optics For Passenger Car Applications

    Science.gov (United States)

    Steele, R. E.; Schmitt, H. J.

    1987-12-01

    The benefits of fiber optics for telecommunications and Local Area Networks (LANs) are well documented. The benefits to passenger car applications are not as clearly defined. This paper examines the differences between Telecommunications, LAN, and automotive point to point and network applications. Current production automotive applications of optics and fiber optics, automotive data communications trends, and both functional and non-functional requirements and constraints will be described.

  19. Concept of accident and injury of air passengers

    Directory of Open Access Journals (Sweden)

    Đurđev Dušanka

    2014-01-01

    Full Text Available Despite the efforts from the international community to create an unified liability regime in Private International Air Law, there are still significant hurdles to be overcome. Many essential rules from this legal regime are vague and open to interpretation. The role of judges is crucial in order to give them their intended meaning. Thus, this paper examines jurisprudence concerning carrier liability in case of death or injury of passengers.

  20. Design of limited-stop service based on the degree of unbalance of passenger demand

    Science.gov (United States)

    2018-01-01

    This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands. PMID:29505585

  1. Design of limited-stop service based on the degree of unbalance of passenger demand.

    Science.gov (United States)

    Zhang, Hu; Zhao, Shuzhi; Liu, Huasheng; Liang, Shidong

    2018-01-01

    This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands.

  2. Weasel works SA-150: Design study of a 100 to 150 passenger transport aircraft

    Science.gov (United States)

    Alkema, Kevin; Comeaux, Michael; Gilbert, Timothy; Para, Victor; Toepfer, George

    1993-01-01

    As the year 2000 rapidly approaches, the airlines are faced with an extremely competitive and environmentally restrictive marketplace. In order to survive, commercial air carriers will need to find new ways to lower their direct operating costs, increase load factors and comply with tightening federal and international constraints. The SA-150 has been designed to meet these demands by focusing on the areas of aerodynamic efficiency, an improved level of passenger comfort, and a limited application of advanced technology. The SA-150 has been optimized for a 500 nmi. mission to help the airlines meet the challenges of the short haul, quick turnaround flight. With a maximum capacity of 124 passengers, and full baggage, the SA-150 is also capable of covering a range of 1500 nmi. This additional range capability will provide the airlines with flexibility when scheduling their routes. The aircraft features a 'V' tail, fly-by-wire system and is powered by two turbofans mounted under a twelve aspect ratio wing. The SA-150 will have an initial production run of 800 units and have a purchase price of $37.7 million in 1993 dollars.

  3. Development of a Novel System to Measure a Clearance of a Passenger Platform

    Science.gov (United States)

    Shimizu, M.; Oizumi, J.; Matsuoka, R.; Takeda, H.; Okukura, H.; Ooya, A.; Koike, A.

    2016-06-01

    Clearances of a passenger platform at a railway station should be appropriately maintained for safety of both trains and passengers. In most Japanese railways clearances between a platform and a train car is measured precisely once or twice a year. Because current measurement systems operate on a track, the closure of the track is unavoidable. Since the procedure of the closure of a track is time-consuming and bothersome, we decided to develop a new system to measure clearances without the closure of a track. A new system is required to work on a platform and the required measurement accuracy is less than several millimetres. We have adopted a 3D laser scanner and stop-and-go operation for a new system. The current systems on a track measure clearances continuously at walking speed, while our system on a platform measures clearances at approximately ten metres intervals. The scanner controlled by a PC acquires a set of point data at each measuring station. Edge points of the platform, top and side points of two rails are detected from the acquired point data. Finally clearances of the platform are calculated by using the detected feature points of the platform and the rails. The results of an experiment using a prototype of our system show that the measurement accuracy by our system would be satisfactory, but our system would take more time than the current systems. Since our system requires no closure of a track, we conclude that our system would be convenient and effective.

  4. An RFID-based luggage and passenger tracking system for airport security control applications

    Science.gov (United States)

    Vastianos, George E.; Kyriazanos, Dimitris M.; Kountouriotis, Vassilios I.; Thomopoulos, Stelios C. A.

    2014-06-01

    Market analysis studies of recent years have shown a steady and significant increase in the usage of RFID technology. Key factors for this growth were the decreased costs of passive RFIDs and their improved performance compared to the other identification technologies. Besides the benefits of RFID technologies into the supply chains, warehousing, traditional inventory and asset management applications, RFID has proven itself worth exploiting on experimental, as well as on commercial level in other sectors, such as healthcare, transport and security. In security sector, airport security is one of the biggest challenges. Airports are extremely busy public places and thus prime targets for terrorism, with aircraft, passengers, crew and airport infrastructure all subject to terrorist attacks. Inside this labyrinth of security challenges, the long range detection capability of the UHF passive RFID technology can be turned into a very important tracking tool that may outperform all the limitations of the barcode tracking inside the current airport security control chain. The Integrated Systems Lab of NCSR Demokritos has developed an RFID based Luggage and Passenger tracking system within the TASS (FP7-SEC-2010-241905) EU research project. This paper describes application scenarios of the system categorized according to the structured nature of the environment, the system architecture and presents evaluation results extracted from measurements with a group of different massive production GEN2 UHF RFID tags that are widely available in the world market.

  5. Passenger Perception towards E-ticketing Services, Airline Industry

    Directory of Open Access Journals (Sweden)

    Dr.Sc. Nail Reshidi

    2014-02-01

    Full Text Available This paper aims to identify the critical dominant incidents and key instigators that influence on usage or lack of usage of e-ticketing by Kosovo Air Passengers. The research at hand utilizes the Grounded Theory of Barney Glaser and Anselm Strauss, and the Critical Incident Technique in order to identify the factors that influence on the (diss satisfaction of the travellers in using e-ticketing. For the purpose of this paper, the empirical data were gathered through interviews by using open ended questions. Among 93 interviews with the random selected passengers, 13 interviews were deemed as invalid. The empirical results highlighted the need for raising the consciousness regarding the efficacy and the advantages of eticketing. On the other hand, many other passengers cannot conceive the possibility of travelling without use of e-ticketing, given that in the past they spent much time in finding the right agent, desired destination, purchase difficulties in making reservation, confirmation, changes, or they had to carry large amounts of cash money to buy tickets which raised insecurity concerns. Research is limited only to the description of critical incidents that occurred in Prishtina International Airport. Majority of the respondents were highly-educated with high income status. These characteristics create a bias and constrain our ability to extrapolate from the findings. Nevertheless, the study serves as a point for more in-depth analysis and discussion on e-ticketing behaviour in Airline industry.

  6. Noise in the passenger cars of high-speed trains.

    Science.gov (United States)

    Hong, Joo Young; Cha, Yongwon; Jeon, Jin Yong

    2015-12-01

    The aim of this study is to investigate the effects of both room acoustic conditions and spectral characteristics of noises on acoustic discomfort in a high-speed train's passenger car. Measurement of interior noises in a high-speed train was performed when the train was operating at speeds of 100 km/h and 300 km/h. Acoustic discomfort caused by interior noises was evaluated by paired comparison methods based on the variation of reverberation time (RT) in a passenger car and the spectral differences in interior noises. The effect of RT on acoustic discomfort was not significant, whereas acoustic discomfort significantly varied depending on spectral differences in noise. Acoustic discomfort increased with increment of the sound pressure level (SPL) ratio at high frequencies, and variation in high-frequency noise components were described using sharpness. Just noticeable differences of SPL with low- and high-frequency components were determined to be 3.7 and 2.9 dB, respectively. This indicates that subjects were more sensitive to differences in SPLs at the high-frequency range than differences at the low-frequency range. These results support that, for interior noises, reduction in SPLs at high frequencies would significantly contribute to improved acoustic quality in passenger cars of high-speed trains.

  7. Influence of unsteady aerodynamics on driving dynamics of passenger cars

    Science.gov (United States)

    Huemer, Jakob; Stickel, Thomas; Sagan, Erich; Schwarz, Martin; Wall, Wolfgang A.

    2014-11-01

    Recent approaches towards numerical investigations with computational fluid dynamics methods on unsteady aerodynamic loads of passenger cars identified major differences compared with steady-state aerodynamic excitations. Furthermore, innovative vehicle concepts such as electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore, the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve handling and ride characteristics at high velocity of the actual range of vehicle layouts, the influence of unsteady excitations on the vehicle response was investigated. For this purpose, a simulation of the vehicle dynamics through multi-body simulation was used. The impact of certain unsteady aerodynamic load characteristics on the vehicle response was quantified and key factors were identified. Through a series of driving simulator tests, the identified differences in the vehicle response were evaluated regarding their significance on the subjective driver perception of cross-wind stability. Relevant criteria for the subjective driver assessment of the vehicle response were identified. As a consequence, a design method for the basic layout of passenger cars and chassis towards unsteady aerodynamic excitations was defined.

  8. Experimental verification of numerical calculations of railway passenger seats

    Science.gov (United States)

    Ligaj, B.; Wirwicki, M.; Karolewska, K.; Jasińska, A.

    2018-04-01

    The construction of railway seats is based on industry regulations and the requirements of end users, i.e. passengers. The two main documents in this context are the UIC 566 (3rd Edition, dated 7 January 1994) and the EN 12663-1: 2010+A1:2014. The study was to carry out static load tests of passenger seat frames. The paper presents the construction of the test bench and the results of experimental and numerical studies of passenger seat rail frames. The test bench consists of a frame, a transverse beam, two electric cylinders with a force value of 6 kN, and a strain gauge amplifier. It has a modular structure that allows for its expansion depending on the structure of the seats. Comparing experimental results with numerical results for points A and B allowed to determine the existing differences. It follows from it that higher stress values are obtained by numerical calculations in the range of 0.2 MPa to 35.9 MPa.

  9. Norwegian airline passengers are not more afraid of flying after the terror act of September 11. The flight anxiety, however, is significantly attributed to acts of terrorism.

    Science.gov (United States)

    Ekeberg, Oivind; Fauske, Berit; Berg-Hansen, Bente

    2014-10-01

    The aim of this paper is to study: (1) the prevalence of flight anxiety among Norwegian airline passengers; (2) situations that may be of concern during flights and situations not related to flying; (3) whether passengers feel more afraid after the terror act of September 11, 2001; and (4) whether passengers were more afraid in 2002 than in 1986.A questionnaire was distributed during domestic flights in Norway in 1986 and 2002. To asses flight anxiety, a six point scale was used, from 0 = not afraid at all, to 5 = always very afraid, and sometimes avoid flying because of that. A 10-cm visual analogue scale (VAS) was used to measure the degree of anxiety. There were 50.8% who were not afraid at all. There were 12 women (5.2%) and one man (0.4%) with flight phobia. However, 22 (4.5%) had cancelled flights because of anxiety during the last two years. Situations that caused most concern during flights were turbulence and fear of terrorism and highjacking. After September 11, 48% were not more afraid, 38% a little more, 10% moderately, 3% rather much and 2% very much. The passengers, however, were not more afraid of flying in 2002 than in 1986. About 3% of Norwegian airline passengers have a flight phobia. Women are significantly more concerned than men. The impact of the terror act September 11, 2001 was rather moderate. The level of flight anxiety among Norwegian airline passengers was not significantly different in 2002 and 1986. © 2014 Oslo University Hospital. Scandinavian Journal of Psychology published by Scandinavian Psychological Associations and John Wiley & Sons Ltd.

  10. An Experimental Analysis on Dispatching Rules for the Train Platforming Problem in Busy Complex Passenger Stations

    Directory of Open Access Journals (Sweden)

    Qiongfang Zeng

    2017-09-01

    platforming problem (TPP by using mixed integer linear programming and job shop scheduling theory. First, the operation procedures and scheduled time adjustment costs of different train types specific to busy complex passenger stations are explicitly represented. Second, a multi-criteria scheduling model (MCS for TPP without earliness and tardiness time window (ETTW and a time window scheduling model (TWS with ETTW for TPP are proposed. Third, various dispatching rules were designed by incorporating the dispatcher experiences with modern scheduling theory and a rule-based metaheuristic to solve the above model is presented. With solution improvement strategies analogous to those used in practice by dispatchers, the realistic size problems in acceptable time can be solved.

  11. High speed rail and coastal tourism: Identifying passenger profiles and travel behaviour.

    Science.gov (United States)

    Gutiérrez, Aaron; Ortuño, Armando

    2017-01-01

    In this paper, we characterise tourists most likely to visit a coastal destination by high-speed rail (HSR). Our data came from a survey conducted among HSR passengers during 2014's high season (July and August) at Spain's Camp de Tarragona and Alicante Stations, each of which is near a mass tourism destination on the Mediterranean coast: the Costa Daurada and the Costa Blanca, respectively. We used responses to the survey, which presented binary discrete-choice situations, to construct a database necessary for a logistic regression model that allowed us to examine how passenger profile, trip characteristics, and stay conditions influenced the use of HSR services on visits to each coastal destination. Results highlighted significant differences in the profiles of tourists who arrived at each destination by HSR and, in turn, that no specific tourist profile is associated with HSR, even for two stations that serve sunny beach destinations. Among its implications, to analyse travellers that HSR can attract, it is vital to consider the specific characteristics of each destination and its current market.

  12. The Impact of Drive Cycles and Auxiliary Power on Passenger Car Fuel Economy

    Directory of Open Access Journals (Sweden)

    Thomas Grube

    2018-04-01

    Full Text Available In view of the advancement of zero emission transportation and current discussions on the reliability of nominal passenger car fuel economy, this article considers the procedure for assessing the potential for reducing the fuel consumption of passenger cars by using electric power to operate them. The analysis compares internal combustion engines, hybrid and fully electric concepts utilizing batteries and fuel cells. The starting point for the newly developed, simulation-based fuel consumption analysis is a longitudinal vehicle model. Mechanical power requirements on the drive side incorporate a large variety of standardized drive cycles to simulate typical patterns of car usage. The power requirements of electric heating and air conditioning are also included in the simulation, as these are especially relevant to electric powertrains. Moreover, on-board grid-load profiles are considered in the assessment. Fuel consumption is optimized by applying concept-specific operating strategies. The results show that the combination of low average driving speed and elevated onboard power requirements have severe impacts on the fuel efficiency of all powertrain configurations analyzed. In particular, the operational range of battery-electric vehicles is strongly affected by this due to the limited storage capacity of today’s batteries. The analysis confirms the significance of considering different load patterns of vehicle usage related to driving profiles and onboard electrical and thermal loads.

  13. Moving characteristics of single file passengers considering the effect of ship trim and heeling

    Science.gov (United States)

    Sun, Jinlu; Lu, Shouxiang; Lo, Siuming; Ma, Jian; Xie, Qimiao

    2018-01-01

    Ship listing and motion affects the movement pattern of passengers on board, thus pedestrian traffic and evacuation dynamics would be significantly different from those on level ground. To quantify the influence of ship listing and motion on passenger evacuation, we designed a ship corridor simulator, with which we performed single-file pedestrian movement experiments considering the effect of trim and heeling. Results indicated that density is not the only factor that affects pedestrian speed under ship trim or heeling conditions, for that both individual walking speed and group walking speed would be greatly attenuated due to the influence of the trim angles. However, heeling angles show less impact on speed when compared with trim angles. In addition, the speed correlation coefficient between the adjacent experimental subjects would be higher with larger angles and lower speed. Moreover, both female and male experimental subjects need similar distance headway for walking in different trim or heeling conditions. Furthermore, experimental subjects with lower individual walking speed need longer time headway to keep enough distance headway. This work will provide fundamental guidance to the development of evacuation models and the design of evacuation facilities on board.

  14. Developing Singapore Driving Cycle for passenger cars to estimate fuel consumption and vehicular emissions

    Science.gov (United States)

    Ho, Sze-Hwee; Wong, Yiik-Diew; Chang, Victor Wei-Chung

    2014-11-01

    Singapore has pledged to attain 7-11% Business-As-Usual carbon emissions reduction by 2020. Road transport sector is a significant source of carbon emissions, estimated to be the third largest sector in Singapore. A current gap in environmental evaluation for road transport activities in Singapore is the lack of a representative driving cycle for passenger cars (64% of the total population of 974,170 vehicles). This Singapore Driving Cycle (SDC) is hence developed for Singapore roads and traffic conditions. A chase-car (instrumented vehicle) was used to collect on-road data along 12 designed routes, and circulation driving on highly utilized arterial roads (including those in Central Business District (CBD) and both inner and outer ring roads fringing the CBD area). The SDC was thus hence constructed, with consideration of road type proportions, time periods and desired distance, duration and peak-lull proportion. In essence, the SDC is a 2400-s speed-time profile to represent the driving pattern for passenger car in Singapore. Microscopic estimation model (CMEM) shows that, as compared to SDC, the New European Driving Cycle (NEDC) underestimates most of the vehicular emissions (fuel, CO2, HC and NOx by 5%, 5%, 22% and 47%, respectively) and overestimates CO by 8%. The SDC is thus more suitable than the NEDC that is currently in use in Singapore; the SDC can be used to generate more accurate fuel consumption and emissions ratings for various uses (for example, inventory of vehicular emissions and fuel economy labelling).

  15. Velocity-dependent emission factors of benzene, toluene and C 2-benzenes of a passenger car equipped with and without a regulated 3-way catalyst

    Science.gov (United States)

    Heeb, Norbert V.; Forss, Anna-Maria; Bach, Christian; Mattrel, Peter

    Time-resolved chemical ionization mass spectrometry (CI-MS) has been used to investigate the velocity-dependent emission factors for benzene, toluene, the C 2-benzenes (xylenes and ethyl benzene) and nitrogen monoxide of a gasoline-driven passenger car (1.4 l, model year 1995) driven with or without catalytic exhaust gas treatment. A set of seven different driving cycles - including the European Driving Cycle (EDC), the US Urban (FTP 75) and the Highway driving cycles - with a total driving time of 12,000 s have been studied. From the obtained emission data, two sets of 15,300 and 17,200 data points which represent transient driving in the velocity range of 0-150 km h -1 and in an acceleration window of -2-3 m s -2 were explored to gain velocity-dependent emission factors. The passenger car, equipped with a regulated rhodium-platinum based three-way catalyst, showed optimal conversion efficiency (>95%) for benzene in the velocity range of 60-120 km h -1. The conversion of benzene was reduced (speed and engine load (>130 km h -1). Whereas the conversion efficiency for the class of C 2-benzenes was reduced to 10%, no net conversion could be found for toluene and benzene when driven above 130 km h -1. In contrast, the benzene and toluene emissions exceeded those of the untreated exhaust gas in the velocity range of 130-150 km h -1 by 50-92% and by 10-34%, respectively. Thus, benzene and toluene were formed across the examined three-way catalyst if the engine is operated for an extended time in a fuel-rich mode (lambda<1).

  16. Exploring Concepts of Operations for On-Demand Passenger Air Transportation

    Science.gov (United States)

    Nneji, Victoria Chibuogu; Stimpson, Alexander; Cummings, Mary; Goodrich, Kenneth H.

    2017-01-01

    In recent years, a surge of interest in "flying cars" for city commutes has led to rapid development of new technologies to help make them and similar on-demand mobility platforms a reality. To this end, this paper provides analyses of the stakeholders involved, their proposed operational concepts, and the hazards and regulations that must be addressed. Three system architectures emerged from the analyses, ranging from conventional air taxi to revolutionary fully autonomous aircraft operations, each with vehicle safety functions allocated differently between humans and machines. Advancements for enabling technologies such as distributed electric propulsion and artificial intelligence have had major investments and initial experimental success, but may be some years away from being deployed for on-demand passenger air transportation at scale.

  17. On the way to 130 g CO2/km-Estimating the future characteristics of the average European passenger car

    International Nuclear Information System (INIS)

    Fontaras, Georgios; Samaras, Zissis

    2010-01-01

    A new average CO 2 emissions limit for passenger cars was introduced in EU in 2009 imposing gradual average CO 2 emissions reduction to 130 g/km until 2015. This paper attempts to study possible changes in vehicle characteristics for meeting this limit taking into account the average European passenger car of 2007-2008. For this purpose first the most important factors affecting vehicle fuel consumption over the reference cycle (NEDC) are identified. At a second step, the CO 2 benefit from the optimisation of these factors is quantified, through simulations of 6 different passenger cars commonly found in the European fleet. For the simulations Advisor 2002 was employed and validated against published type approval data. The analysis indicated that substantial reductions in vehicle weight, tyre rolling resistance and engine efficiency are necessary to reach even the 2008 target. A 10% reduction in average vehicle weight combined with 10% better aerodynamic characteristics, 20% reduced tyre rolling resistance and a 7.5% increase in average powertrain efficiency can lead to CO 2 reductions of approximately 13% (about 138 g/km based on 2007-2008 fleet-wide performance). Complying with the 130 g/km within the next six-year timeframe will be a rather difficult task and additional technical measures appear to be necessary.

  18. Retrospective review of adverse incidents involving passengers seated in wheeled mobility devices while traveling in large accessible transit vehicles.

    Science.gov (United States)

    Frost, Karen L; Bertocci, Gina

    2010-04-01

    Characterize wheeled mobility device (WhMD) adverse incidents on large accessible transit vehicles (LATVs) based on vehicle motion, WhMD activity during incident, incident scenario and injury. Retrospective records review. WhMD passengers traveling on LATVs while remaining seated in their. Adverse incidents characterized based on vehicle motion, WhMD activity during incident, and incident scenario. Injury characterized based on outcome, medical attention sought, vehicle activity, WhMD activity and incident scenario. 115 WhMD-related incident reports for years 2000-2005 were analyzed. Most incidents occurred when the LATV was stopped (73.9%), during ingress/egress (42.6%), and at the securement station (33.9%) when the LATV was moving. The combination of WhMD tipping and passenger falling (43.4%) occurred most frequently, and was 1.8 times more likely to occur during ingress/egress than at the securement station. One-third (33.6%) of all incidents resulted in injury, and injuries were equally distributed between ingress/egress (43.6%) and at the securement station (43.6%). WhMD users have a greater chance of incurring injury during ingress/egress than during transit. Research is needed to objectively assess real world transportation experiences of WhMD passengers, and to assess the adequacy of existing federal legislation/guidelines for accessible ramps used in public transportation. Copyright 2009 IPEM. Published by Elsevier Ltd. All rights reserved.

  19. Commercial suborbital space tourism-proposal on passenger's medical selection

    Science.gov (United States)

    Kluge, Götz; Stern, Claudia; Trammer, Martin; Chaudhuri, Indra; Tuschy, Peter; Gerzer, Rupert

    2013-12-01

    Commercial human spaceflight has excellent economic and technical perspectives in the next decades. Passengers will be persons from a general population differing from culture, age, gender and health status. They all will have to withstand physical loads of spaceflight such as acceleration and deceleration forces, microgravity, vibration, noise and radiation. There is a necessity to mitigate all negative impacts on the passengers' health. Besides precautionary measures in construction and equipment, a diligent medical selection and pre-flight training is recommended. To ensure an easy and at the same time qualified selection procedure, it is necessary to define medical selection criteria and training methods. As experiences with suborbital spaceflight of private passengers are still few we recommend to implement in the beginning of this new era maximum safety standards. Having performed a satisfactory number of successful flights, some of the selection criteria and training sessions might be loosened or modified. This judicious approach is in the interest of the spaceflight participants as well as of the providing companies. As a guideline we propose a four step approach that allows a quick decision concerning the fitness of participants to fly as well as an intensive preparation of the passengers. For the first two steps positive experiences from medical screening and examination of professional pilots can be utilised. According to JAR-FCL 3 (Joint Aviation Requirements-Flight Crew Licensing, Chapter 3) a questionnaire with medical interview targeting the medical background of the respective person and including no-go criteria provides a first estimation for applicants and medical examiners whether there will be a chance to be accepted as a passenger. The second step of selection comprises the physical examination of the applicant adjusted to the professional pilot's examination procedure. As the physical challenges of the suborbital flight will exceed the impact

  20. Drivers' and conductors' views on the causes and ways of preventing workplace violence in the road passenger transport sector in Maputo City, Mozambique

    Directory of Open Access Journals (Sweden)

    Tillgren Per

    2011-10-01

    Full Text Available Abstract Background Workplace violence (WPV is an occupational health hazard in both low and high income countries. To design WPV prevention programs, prior knowledge and understanding of conditions in the targeted population are essential. This study explores and describes the views of drivers and conductors on the causes of WPV and ways of preventing it in the road passenger transport sector in Maputo City, Mozambique. Methods The design was qualitative. Participants were purposefully selected from among transport workers identified as victims of WPV in an earlier quantitative study, and with six or more years of experience in the transport sector. Data were collected in semi-structured interviews. Seven open questions covered individual views on causes of WPV and its prevention, based on the interviewees' experiences of violence while on duty. Thirty-two transport professionals were interviewed. The data were analyzed by means of qualitative content analysis. Results The triggers and causes of violence included fare evasion, disputes over revenue owing to owners, alcohol abuse, overcrowded vehicles, and unfair competition for passengers. Failures to meet passenger expectations, e.g. by-passing parts of a bus route or missing stops, were also important. There was disrespect on the part of transport workers, e.g. being rude to passengers and jumping of queues at taxi ranks, and there were also robberies. Proposals for prevention included: training for workers on conflict resolution, and for employers on passenger-transport administration; and, promoting learning among passengers and workers on how to behave when traveling collectively. Regarding control and supervision, there were expressed needs for the recording of mileage, and for the sanctioning of workers who transgress queuing rules at taxi ranks. The police or supervisors should prevent drunken passengers from getting into vehicles, and drivers should refuse to go to dangerous, secluded

  1. Human Factors Engineering in Designing the Passengers' Cockpit of the Malaysian Commercial Suborbital Spaceplane

    Science.gov (United States)

    Ridzuan Zakaria, Norul; Mettauer, Adrian; Abu, Jalaluddin; Hassan, Mohd Roshdi; Ismail, Anwar Taufeek; Othman, Jamaluddin; Shaari, Che Zhuhaida; Nasron, Nasri

    2010-09-01

    The design of the passengers’ cabin or cockpit of commercial suborbital spaceplane is a new and exciting frontier in human factors engineering, which emphasizes on comfort and safety. There is a program to develop small piloted 3 seats commercial suborbital spaceplane by a group of Malaysians with their foreign partners, and being relatively small and due to its design philosophy, the spaceplane does not require a cabin, but only a cockpit for its 2 passengers. In designing the cockpit, human factors engineering and safety principles are given priority. The cockpit is designed with the intention to provide comfort and satisfaction to the passengers without compromising the safety, in such a way that there are passenger-view wide angled video camera to observe the passengers at all time in flight, “rear-view”, “under-the-floor-view” and “fuselage-view” video cameras for the passengers, personalized gauges and LCDs on the dashboard to provide vital and useful information during the flight to the passengers, and biomedical engineered products which not only entertain the passengers, but also provide important information on the passengers to the ground crews who are responsible in the comfort and safety of the passengers. The passenger-view video-camera, which record the passengers with Earth visible through the glass canopy as the background, not only provides live visual of the passengers for safety reason, but also provide the most preferred memorable video collection for the passengers, while other video cameras provide the opportunity to view at various angles from unique positions to both the passengers and the ground observers. The gauges and LCDs on the dashboard provide access to the passengers to information such as the gravity, orientation, rate of climb and flight profile of the spaceplane, graphical presentation of the spaceplane in flight, and live video from the onboard video cameras. There is also a control stick for each passenger to

  2. Analyzing Factors Of In-flight Services Of Garuda Indonesia And Batik Air Towards Passengers Satisfaction

    OpenAIRE

    Tumewu, Ferdinand; Tulandi, Victor Michael

    2014-01-01

    Transportation services play an important role in supporting any activity, of human. Various types of the transportation that we use. Among them, are air transportation or airplane. Talk about the satisfaction of airline passenger, nowadays many airlines competing to provide the best service for the passengers, one of the things that can influence passenger satisfaction is through airline service especially in-flight service. The objective of this research is to identify the factors of in-fli...

  3. [Comfort of crew and passengers and atmospheric pressure, noise, wind speed in high-speed train of Shijiazhuang-Taiyuan passenger dedicated line].

    Science.gov (United States)

    Zhai, Yi-biao; Huo, Wei; Liu, Qiao-ying; Chen, Bao-shan; Zhang, Jin-long; Shi, Lei

    2012-11-01

    To explore the crew and passengers' comfort on the Shijiazhuang-Taiyuan passenger dedicated line and physical factors, such as air pressure, noise, wind speed. Comfort investigation of all the crew (n = 244) and passengers (n = 377) on the Shijiazhuang-Taiyuan passenger dedicated line at speed of 250 km/h and 200 km/h and the detection of the air pressure, noise and wind speed were performed in 2011. Significantly higher ratio of comfortable feeling, lower ratio of seriously discomfortable feeling were observed in crew and passengers at 200 km/h compared with those at 250 km/h (P noise in passengers at 200 km/h. No significant difference was observed in ear discomfort induced by air pressure and noise among crew, and the duration of disappearance of discomfortable feeling among passengers between 200 km/h and 250 km/h. The noise in carriages exceeded the related standard when the high-speed train passing through the tunnels. The individuals feel more comfortable at 200 km/h than 250 km/h in this line., which may be related with rapid variation of wind speed and noise when the train passes through the tunnels with high speed.

  4. Solar-ships, solar passenger vessels in public passenger traffic; Solarschiffe, Solarfahrgastschiffe im oeffentlichen Personenverkehr

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, T. [Ingenieurbuero Schiffbau und Meerestechnik, Inst. fuer Solarschiffbau, Berlin und Hameln (Germany)

    1999-07-01

    It should first be said that solar boats are nothing other than electrically powered boats with their own independent, silent and clean power generator with which to recharge the storage batteries with free solar energy. There are only very few connection points to the public electricity grid on the open sea, on inland waterways and along their shores and banks. This fact has resulted in the many battery- and photo-voltaic-powered beacons and buoys that are so common today. But people who live aboard inland vessels, yachts, space stations and house boats are equally dependent on energy provided by electric storage batteries. Solar electricity generators are reliable, robust and perform their given task without requiring major maintenance work. This has resulted in ever more areas of application for solar electricity, also favoured by constantly falling prices and ever improving technology. Some of the currently available photo-voltaic modules are already pliable enough to form a single unit with the roof of a boat (see photo of the Aquabus 1050). Electric motors are older and more reliable than combustion engines. The motor can always be started just as long as the storage batteries have been recharged, i.e. the tank is full, and an electrical current is applied. In actual fact, such electric motors are in widespread use as nearly every cruise liner, submarine and even torpedo is equipped with electric drives. There are various reasons for this, such as a low degree of oscillation, silent operation and reliability. Large passenger-carrying vessels, however, do not use storage batteries but rather generate their electricity directly using numerous smaller diesel engines. (orig.) [German] Solarboote sind eigentlich nur Elektroboote, die ueber ihr eigenes unabhaengiges sauberes Kraftwerk verfuegen, das mit kostenloser Energie von der Sonne die Akkus auflaedt, ohne Kraftstoffe zu benoetigen. Auf den Meeren und Binnengewaessern sowie entlang ihrer Ufer gibt es nur

  5. Models for Information Assurance Education and Outreach: A Report on Year 1 Implementation

    Science.gov (United States)

    Wang, Jianjun

    2013-01-01

    On September 22, 2012, NSF announced its decision to fund a three-year project, "Models for Information Assurance Education and Outreach" (MIAEO). In the first year of grant operation, MIAEO has invited 18 high school students, two K-12 teachers, and two CSUB student assistants to conduct research explorations in the fields of…

  6. Continuous Improvement of a Groundwater Model over a 20-Year Period: Lessons Learned.

    Science.gov (United States)

    Andersen, Peter F; Ross, James L; Fenske, Jon P

    2018-04-17

    Groundwater models developed for specific sites generally become obsolete within a few years due to changes in: (1) modeling technology; (2) site/project personnel; (3) project funding; and (4) modeling objectives. Consequently, new models are sometimes developed for the same sites using the latest technology and data, but without potential knowledge gained from the prior models. When it occurs, this practice is particularly problematic because, although technology, data, and observed conditions change, development of the new numerical model may not consider the conceptual model's underpinnings. As a contrary situation, we present the unique case of a numerical flow and trichloroethylene (TCE) transport model that was first developed in 1993 and since revised and updated annually by the same personnel. The updates are prompted by an increase in the amount of data, exposure to a wider range of hydrologic conditions over increasingly longer timeframes, technological advances, evolving modeling objectives, and revised modeling methodologies. The history of updates shows smooth, incremental changes in the conceptual model and modeled aquifer parameters that result from both increase and decrease in complexity. Myriad modeling objectives have included demonstrating the ineffectiveness of a groundwater extraction/injection system, evaluating potential TCE degradation, locating new monitoring points, and predicting likelihood of exceedance of groundwater standards. The application emphasizes an original tenet of successful groundwater modeling: iterative adjustment of the conceptual model based on observations of actual vs. model response. © 2018, National Ground Water Association.

  7. Adolescents Exiting Homelessness over Two Years: The Risk Amplification and Abatement Model

    Science.gov (United States)

    Milburn, Norweeta G.; Rice, Eric; Rotheram-Borus, Mary Jane; Mallett, Shelley; Rosenthal, Doreen; Batterham, Phillip; May, Susanne J.; Witkin, Andrea; Duan, Naihua

    2009-01-01

    The Risk Amplification and Abatement Model (RAAM) demonstrates that negative contact with socializing agents amplify risk, while positive contact abates risk for homeless adolescents. To test this model, the likelihood of exiting homelessness and returning to familial housing at 2 years and stably exiting over time are examined with longitudinal…

  8. Mathematical Modelling in the Junior Secondary Years: An Approach Incorporating Mathematical Technology

    Science.gov (United States)

    Lowe, James; Carter, Merilyn; Cooper, Tom

    2018-01-01

    Mathematical models are conceptual processes that use mathematics to describe, explain, and/or predict the behaviour of complex systems. This article is written for teachers of mathematics in the junior secondary years (including out-of-field teachers of mathematics) who may be unfamiliar with mathematical modelling, to explain the steps involved…

  9. An Integrated Visualization and Basic Molecular Modeling Laboratory for First-Year Undergraduate Medicinal Chemistry

    Science.gov (United States)

    Hayes, Joseph M.

    2014-01-01

    A 3D model visualization and basic molecular modeling laboratory suitable for first-year undergraduates studying introductory medicinal chemistry is presented. The 2 h practical is embedded within a series of lectures on drug design, target-drug interactions, enzymes, receptors, nucleic acids, and basic pharmacokinetics. Serving as a teaching aid…

  10. Thermoelectric Waste Heat Recovery Program for Passenger Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jovovic, Vladimir [Gentherm Incorporated, Azusa, CA (United States)

    2015-12-31

    Gentherm began work in October 2011 to develop a Thermoelectric Waste Energy Recovery System for passenger vehicle applications. Partners in this program were BMW and Tenneco. Tenneco, in the role of TIER 1 supplier, developed the system-level packaging of the thermoelectric power generator. As the OEM, BMW Group demonstrated the TEG system in their vehicle in the final program phase. Gentherm demonstrated the performance of the TEG in medium duty and heavy duty vehicles. Technology developed and demonstrated in this program showed potential to reduce fuel consumption in medium and heavy duty vehicles. In light duty vehicles it showed more modest potential.

  11. 9. Anti-vibration Design of a Passenger Ship

    OpenAIRE

    Kazuo, Umezaki; Mikihiro, Kobayashi; Hioshi Kohkawa, Kohkawa; Hiroyuki, Mizuno; Shin-ichi, Nishimura; Takayuki, Okayasu; Kazuhisa, Yanagi; Mitsubishi Heavy Industries. Ltd; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries. Ltd; Mitsubishi Heavy Industries, Ltd. Kobe Shipyard and Machinery Works; Mitsubishi Heavy Industries, Ltd. Nagasaki Research and Development Center

    1992-01-01

    One of the most difficult tasks in designing a passenger ship is to make it vibration free while keeping the hull structure very light for stability reason. In order to accomplish this for the 23,000 GT cruise ship the particulars of which are shown in Table l, special attention was paid to the alignment of structures during layout design, and analyses and experiments of vibration were carried out through every stage of design and construction. This paper describes outlines of these tasks and...

  12. Panorama 2009 - trends and challenges in passenger mobility

    International Nuclear Information System (INIS)

    2008-01-01

    Current demand for mobility encourages people to seek fast, individual means of transport. The automobile accounts for the bulk of passenger travel worldwide. This mode of transport is a source of annoying and harmful effects including noise, accidents, deteriorating infrastructure, traffic congestion and pollution (local and atmospheric). Some of these issues are now under regulation and have become less acute, but traffic congestion and greenhouse gas emissions are still major problems. Before assessing any policy undertaken to curb nuisance levels and harmful effects, one must be familiar with global mobility trends and the challenges involved

  13. U. K. surface passenger transport sector. Energy consumption and policy options for conservation

    Energy Technology Data Exchange (ETDEWEB)

    Maltby, D; Monteath, I G; Lawler, K A

    1978-12-01

    Forecasts of U.K. energy consumption in this sector for four future scenarios based on different economic growth rates, energy prices, and energy conservation policies, show that by the year 2000, private transport will probably account for 76-94% of total energy consumption in surface passenger transport. A 33% increase in the average miles-per-gallon fuel consumption through technological improvements in private vehicles, conversion of private vehicles to diesel oil, additional fuel taxation equivalent to 25 or 50% fuel price increase, a 10% reduction in average car engine size (encouraged by taxation), and changes in public transport technology offer energy savings of about 20, 5-10, 6.3 or 12.5, 2-4, and 2%, respectively. There is considerable uncertainty about the outcome of these options.

  14. Nano-Continuum Modeling of a Nuclear Glass Specimen Altered for 25 Years

    Energy Technology Data Exchange (ETDEWEB)

    Steefel, Carl

    2014-01-06

    The purpose of this contribution is to report on preliminary nano-continuum scale modeling of nuclear waste glass corrosion. The focus of the modeling is an experiment involving a French glass SON68 specimen leached for 25 years in a granitic environment. In this report, we focus on capturing the nano-scale concentration profiles. We use a high resolution continuum model with a constant grid spacing of 1 nanometer to investigate the glass corrosion mechanisms.

  15. Passengers at risk: a multi-level analysis of the decision to travel with a drunk driver.

    Science.gov (United States)

    Nazif-Muñoz, José Ignacio; Blank-Gomel, Aharon

    2017-06-01

    To assess the impact of demographic, intrapersonal and environmental factors on the likelihood in Chile of becoming a passenger of an alcohol-impaired driver (PAID). Multi-level cross-sectional study. Data were acquired from two large-scale household surveys of representative samples of Chile's Metropolitan Region. The study included 1341 individuals ≥ 16 years; 696 of them reported engaging in PAID. The primary outcome was self-reported frequencies of having accepted a ride with an alcohol-impaired driver. PAID was associated significantly with 'age' [odds ratio (OR) = 0.99, 95% confidence interval (CI) = 0.98-0.99, P = 0.03], 'traffic safety beliefs' (OR = 0.17, 95% CI = 0.078-0.44, P = 0.00), 'time exposure as passenger' (OR = 1.00, 95% CI = 1.00-1.01, P = 0.00) and 'sex' (OR = 0.67, 95% CI = 0.53-0.87, P = 0.00). In women, PAID was associated with 'age' (OR = 0.98, 95% CI = 0.97-0.99, P = 0.02), 'traffic safety beliefs' (OR = 0.17, 95% CI = 0.05-0.59, P = 0.00) and 'low quality of public bus stops' (OR = 0.97, 95% CI = 0.98-0.99, P = 0.01). Younger women with high education levels were more likely to engage in PAID than younger women with low education levels. In men, PAID was associated with 'traffic safety beliefs' (OR = 0.13, 95% CI = 0.02-0.63, P = 0.01) and 'time exposure as passenger' (OR = 1.00, 95% CI = 1.00-1.01, P = 0.02). In Chile, men are at higher risk of becoming a passenger of an alcohol-impaired driver (PAID) than women. In women, PAID appears to be associated with lower traffic safety beliefs, lower quality of public bus stations and an interaction between education and age. In men, PAID is associated with lower traffic safety beliefs and higher time exposure as passenger. © 2017 Society for the Study of Addiction.

  16. 40 CFR 1068.360 - What restrictions apply to assigning a model year to imported engines and equipment?

    Science.gov (United States)

    2010-07-01

    ... new engine identified as a 2007 model-year product that is imported on January 31, 2010 will be... equipment? This section includes limitations on assigning a model year to engines and equipment that are imported in a year later than the model year in which they were manufactured, except as specified in...

  17. A comparison of two exact methods for passenger railway rolling stock (re)scheduling

    DEFF Research Database (Denmark)

    Haahr, Jørgen Thorlund; Wagenaar, Joris C.; Veelenturf, Lucas P.

    2016-01-01

    The assignment of rolling stock units to timetable services in passenger railways is an important optimization problem that has been addressed by many papers in different forms. Solution approaches have been proposed for different planning phases: strategic, tactical, operational, and real...... is solved using a column and row generation approach. In this paper, we benchmark the performance of the methods on networks of two countries (Denmark and The Netherlands). We use the approaches to make daily schedules and we test their real time applicability by performing tests with different disruption...... scenarios. The computational experiments demonstrate that both models can be used on both networks and are able to find optimal rolling stock circulations in the different planning phases. Furthermore, the results show that both approaches are sufficiently fast to be used in a real-time setting....

  18. Wolbachia infect ovaries in the course of their maturation: last minute passengers and priority travellers?

    Directory of Open Access Journals (Sweden)

    Lise-Marie Genty

    Full Text Available Wolbachia are widespread endosymbiotic bacteria of arthropods and nematodes. Studies on such models suggest that Wolbachia's remarkable aptitude to infect offspring may rely on a re-infection of ovaries from somatic tissues instead of direct cellular segregation between oogonia and oocytes. In the terrestrial isopod Armadillidium vulgare, Wolbachia are vertically transmitted to the host offspring, even though ovary cells are cyclically renewed. Using Fluorescence in situ hybridization (FISH, we showed that the proportion of infected oocytes increased in the course of ovary and oocyte maturation, starting with 31.5% of infected oocytes only. At the end of ovary maturation, this proportion reached 87.6% for the most mature oocytes, which is close to the known transmission rate to offspring. This enrichment can be explained by a secondary acquisition of the bacteria by oocytes (Wolbachia can be seen as last minute passengers and/or by a preferential selection of oocytes infected with Wolbachia (as priority travellers.

  19. Comparative Analysis of Passenger Traffic Fleets in Asian Cities: Technology, Driving Activities, and Emission

    Science.gov (United States)

    KIM Oanh, N. T.; Huynh, H. V.; Saikawa, E.

    2015-12-01

    The road transport sector is the major emission source of toxic air pollutants and greenhouse gases (GHGs) in large Asian cities. This paper comparatively analyzed on-road passenger traffic fleets (cars, buses, taxis, motorcycles), using local data collected in cities of Bangkok (BKK), Kathmandu, Hanoi, Ho Chi Minh City (HCMC), and Yangon. Surveys were done in 2010-2014 to obtain information on vehicle technology, driving activities (speed, distance, number, and types of starts), traffic density, and fuel characteristics. Large shares of pre-Euro vehicles were still observed, especially for public buses. The most advanced technology was Euro4, which was observed in small shares (<5%) of the personal car fleets in BKK, HCMC, and Yangon. Euro3 was generally the most advanced technology found in other fleets in these cities. Motorcycles (MC) was the most dominant fleet in all cities, except in Yangon, where they were not allowed. Low vehicle speeds, mainly below 25 km/h, were observed for all vehicle types, indicating traffic jams. Natural gas and LPG had considerable shares in BKK and Yangon while for other cities diesel and gasoline were still the two major fuels used in transportation. Running emission factors (EF) of buses and taxis in Kathmandu were considerably higher than other cities due to its hilly topography, low speeds, high mileage, and less advanced vehicle technologies. The number of passenger vehicles per 1000 people were 400-500 in HCMC and Hanoi (mainly by MC) and in BKK (also by cars), moderate in Kathmandu (200) and the lowest in Yangon (40) because of the MC ban. Annual emissions of the passenger fleets were calculated for each city using the International Vehicle Emission (IVE) for 14 species. BC and OC emissions were estimated using their fractions of PM10 emission. Annual emission per capita of toxic air pollutants and GHGs was analyzed. For example, the emission in kg/year/person for CO, VOC, NOx and PM10 in these cities was 24-150 for CO, 0

  20. Discordance between age- and size-based criteria of child passenger restraint appropriateness.

    Science.gov (United States)

    Smiley, Mary L; Bingham, C Raymond; Jacobson, Peter D; Macy, Michelle L

    2018-04-03

    In this study, we sought to accomplish the following objectives: to (1) calculate the percentage of children considered appropriately restrained across 8 criteria of increasing restrictiveness; (2) examine agreement between age- and size-based appropriateness criteria; (3) assess for changes in the percentage of children considered appropriately restrained by the 8 criteria between 2011 (shortly after updates to U.S. guidelines) and 2015. Data from 2 cross-sectional surveys of 928 parents of children younger than 12 years old (n = 591 in 2011, n = 337 in 2015) were analyzed in 2017. Child age, weight, and height were measured at an emergency department visit and used to determine whether the parent-reported child passenger restraint was considered appropriate according to 8 criteria. Age-based criteria were derived from Michigan law and U.S. Weight, height, and size-based criteria were derived from typical restraints available in the United States in 2007 and 2011. The percentage appropriate restraint use was calculated for each criterion. The kappa statistic was used to measure agreement between criteria. Change in appropriateness from 2011 to 2015 was assessed with chi-square statistics. Percentage appropriate restraint use varied from a low of 19% for higher weight limits in 2011 to a high of 91% for Michigan law in 2015. Agreement between criteria was slight to moderate. The lowest kappa was for Michigan law and higher weight limits in 2011 (κ = 0.06) and highest for U.S. guidelines and lower weight limits in 2011 (κ = 0.60). Percentage appropriate restraint use was higher in 2015 than 2011 for the following criteria: U.S. guidelines (74 vs. 58%, P consistency in reporting results from studies of child passenger safety in the United States. Potential explanations for the increased percentage of children considered appropriately restrained between 2011 and 2015 include adoption of the updated U.S. guidelines and the use of child passenger restraints with