Quantifying in situ stress magnitudes and orientations for Forsmark. Forsmark stage 2.2

Energy Technology Data Exchange (ETDEWEB)

Martin, C. Derek (Univ. of Alberta (Canada))

2007-11-15

Stephansson et al. concluded that in the Fennoscandia shield: (1) there is a large horizontal stress component in the uppermost 1,000 m of bedrock, and (2) the maximum and minimum horizontal stresses exceed the vertical stress assuming the vertical stress is estimated from the weight of the overburden. Several stress campaigns involving both overcoring and hydraulic fracturing, including the hydraulic testing of pre-existing fractures (HTPF), have been carried out at Forsmark to establish the in situ stress state. The results from the initial campaigns were summarised by Sjoeberg et al. which formed the bases for the stresses provided in the Site Descriptive Model version 1.2. Since then additional stress measurement campaigns have been completed. The results from these stress measurement campaigns support the conclusions from Stephansson et al. In addition to these in situ stress measurements the following additional studies were undertaken to aid in assessing the stress state at Forsmark. 1. A detailed televiewer survey of approximately 6,900 m of borehole walls to depths of 1,000 m was carried out to assess borehole wall damage, i.e. borehole breakouts. 2. Evaluation of nonlinear strains in laboratory samples to depths of approximately 800 m to assess if stress magnitudes were sufficient to create stress-induced microcracking. 3. Assessment of the magnitudes required to cause core disking and survey of core disking observed at Forsmark. The magnitudes and orientations from the stress measurement campaigns were analysed to establish the most likely stress magnitudes and orientations for Design Step D2 within the Target Area of the Complete Site Investigations. The maximum and minimum horizontal stress components are essentially the same as the maximum and intermediate principal stresses, sigma1 and sigma2, respectively. The minimum principal stress (sigma3) is synonymous with the vertical stress. The most likely range in values to be used in the design is also

Applicability of initial stress measurement methods to Horonobe Siliceous rocks and initial stress state around Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Sanada, Hiroyuki; Niunoya, Sumio; Matsui, Hiroya; Fujii, Yoshiaki

2009-01-01

Understanding initial stress condition in deep underground is important for such construction as rock cavern for geological disposal of HLW and underground power plant. Neogene sedimentary rock is widely distributed in Japan. There are only a few studies of initial stress measurement in Neogene sedimentary rock mass in Japan due to difficulty of measurement. Evaluation of initial stress condition around Horonobe Underground Research Laboratory Project was carried out in order to understand initial stress condition and applicability of AE, DSCA and hydraulic fracturing (HF) methods to Neogene sedimentary rock. Initial stress values obtained from AE method is smaller than overburden pressure due to time dependency of Kaizer effect. It would be difficult to use AE method as initial stress measurement method for Horonobe Siliceous rocks. Principal stress values by DSCA are similar to those by HF tests. Directions of maximum horizontal principal stresses are approximately in E-W and corresponded to HF results. In HF, rod type and wire-line type systems were compared. Workability of rod type was much better than wire-line type. However, re-opening pressure were not able to be precisely measured in case of rod type system due to the large compliance of the packers and rods. Horizontal maximum and minimum principal stresses increase linearly in HF results. Deviatoric stress is acting at shallow depth. Initial stress condition approaches hydrostatic condition with depth. Direction of maximum horizontal principal stress was in E-W direction which was similar to tectonic movement around Horonobe URL by triangular surveying. (author)

Prediction of minimum UO2 particle size based on thermal stress initiated fracture model

International Nuclear Information System (INIS)

Corradini, M.

1976-08-01

An analytic study was employed to determine the minimum UO 2 particle size that could survive fragmentation induced by thermal stresses in a UO 2 -Na Fuel Coolant Interaction (FCI). A brittle fracture mechanics approach was the basis of the study whereby stress intensity factors K/sub I/ were compared to the fracture toughness K/sub IC/ to determine if the particle could fracture. Solid and liquid UO 2 droplets were considered each with two possible interface contact conditions; perfect wetting by the sodium or a finite heat transfer coefficient. The analysis indicated that particles below the range of 50 microns in radius could survive a UO 2 -Na fuel coolant interaction under the most severe temperature conditions without thermal stress fragmentation. Environmental conditions of the fuel-coolant interaction were varied to determine the effects upon K/sub I/ and possible fragmentation. The underlying assumptions of the analysis were investigated in light of the analytic results. It was concluded that the analytic study seemed to verify the experimental observations as to the range of the minimum particle size due to thermal stress fragmentation by FCI. However the method used when the results are viewed in light of the basic assumptions indicates that the analysis is crude at best, and can be viewed as only a rough order of magnitude analysis. The basic complexities in fracture mechanics make further investigation in this area interesting but not necessarily fruitful for the immediate future

Combining Earthquake Focal Mechanism Inversion and Coulomb Friction Law to Yield Tectonic Stress Magnitudes in Strike-slip Faulting Regime

Science.gov (United States)

Soh, I.; Chang, C.

2017-12-01

The techniques for estimating present-day stress states by inverting multiple earthquake focal mechanism solutions (FMS) provide orientations of the three principal stresses and their relative magnitudes. In order to estimate absolute magnitudes of the stresses that are generally required to analyze faulting mechanics, we combine the relative stress magnitude parameter (R-value) derived from the inversion process and the concept of frictional equilibrium of stress state defined by Coulomb friction law. The stress inversion in Korean Peninsula using 152 FMS data (magnitude≥2.5) conducted at regularly spaced grid points yields a consistent strike-slip faulting regime in which the maximum (S1) and the minimum (S3) principal stresses act in horizontal planes (with an S1 azimuth in ENE-WSW) and the intermediate principal stress (S2) close to vertical. However, R-value varies from 0.28 to 0.75 depending on locations, systematically increasing eastward. Based on the assumptions that the vertical stress is lithostatic, pore pressure is hydrostatic, and the maximum differential stress (S1-S3) is limited by Byerlee's friction of optimally oriented faults for slip, we estimate absolute magnitudes of the two horizontal principal stresses using R-value. As R-value increases, so do the magnitudes of the horizontal stresses. Our estimation of the stress magnitudes shows that the maximum horizontal principal stress (S1) normalized by vertical stress tends to increase from 1.3 in the west to 1.8 in the east. The estimated variation of stress magnitudes is compatible with distinct clustering of faulting types in different regions. Normal faulting events are densely populated in the west region where the horizontal stress is relatively low, whereas numerous reverse faulting events prevail in the east offshore where the horizontal stress is relatively high. Such a characteristic distribution of distinct faulting types in different regions can only be explained in terms of stress

Hydraulic fracturing rock stress measurement at Haestholmen, Finland

International Nuclear Information System (INIS)

Ljunggren, C.; Klasson, H.

1992-12-01

This report presents hydraulic fracturing measurements in two boreholes located on the Haestholmen island near Loviisa, Finland. The aim of the measurements was to provide stress data, forming input for the design of an underground facility for disposal of low- and medium-level waste as well as future plant decommissioning radioactive waste from the IVO reactor units situated on Haestholmen. The theoretical background to the hydrofracturing method is summarized, as is the equipment and experimental procedures used in the present case. All results obtained are presented and critically discussed. The final stress parameters presented are magnitudes and directions of the maximum and minimum horizontal stresses. Testing was successfully completed according to schedule in both boreholes.(orig.)

Determination of in-situ rock stresses related to petroleum activities on the Norwegian Continental Shelf

Energy Technology Data Exchange (ETDEWEB)

Fejerskov, Morten

1996-12-31

In-situ rock stresses have proved to be important for exploration and production of hydrocarbons. This thesis uses various stress determination techniques to characterize the in-situ stress field on the Norwegian Continental Shelf. Leak off tests and borehole breakouts have been used to determine the in-situ stress in deep well bores. Overcoring and earthquake focal mechanisms data have also been compiled and evaluated together with stress information from petroleum wells. A new test procedure is suggested to improve the quality of leak off tests that emphasises the importance of accurate pressure determination, longer test periods and digital data sampling. Four-arm calliper logs are used to identify borehole breakouts on the Tampen Spur and Horda Platform. However, it proved difficult to distinguish borehole breakouts from other drilling processes since the elongations of the borehole consistently appeared in the direction of hole azimuth; drilling-induced key seats are here observed in vertical wells. This behaviour is discussed but not fully understood. This reduces the number of reliable stress data and their quality enormously and even casts some doubt about the quality of previous breakout studies from the North Sea. A highly compressive horizontal stress field seems to be present onshore and offshore Norway. Different stress determination techniques yield very consistent stress orientation, regional and internal variation. A 1. order stress direction is identified, where the maximum horizontal stress direction is rotating from N-S in the Barents Sea to NW-SE in the Norwegian Sea and WNW-ESE in the northern North Sea. At Tampen Spur, a dominant WNW-ESE maximum horizontal stress direction, normal to the major tectonic structures is identified as well as a minimum stress close to the vertical stress, the latter indicating high horizontal stresses. 250 refs., 91 figs., 14 tabs.

Report on televiewer log and stress measurements in core hole USW G-2, Nevada Test Site, October-November, 1982

International Nuclear Information System (INIS)

Stock, J.M.; Healy, J.H.; Hickman, S.H.

1984-01-01

Hydraulic fracturing stress measurements and a borehole televiewer log were obtained in hole USW G-2 at Yucca Mountain, Nevada, to depths of 1200 m. Results indicate that at the depths tested, the minimum ad maximum horizontal stresses are less than the vertical stress, corresponding to a normal faulting stress regime. Drilling-induced hydrofractures seen in the televiewer log imply a least horizontal principal stress direction of N 60 0 W to N 65 0 W. For reasonable values of the coefficient of friction, the magnitude of the least horizontal stress is close to the value at which slip would occur on preexisting faults of optimal orientation (strike N 25 0 E to N 30 0 E and dipping 60 0 to 67 0 ). The prominent drilling-induced fractures seen in the televiewer log are believed to have been caused by excess downhole pressures applied during drilling the hole. Many throughgoing fractures are also seen in the televiewer log; most of these are high angle, stringing N 10 0 E to N 40 0 E. These fractures show a general decrease in angle of dip with depth. Stress-induced wellbore breakouts are seen at depths below 1050 m. The average N 60 0 W azimuth of these breakouts agrees very closely with the N 60 0 W to N 65 0 W direction of least horizontal principal stress inferred from the drilling-induced hydrofracs. 19 references, 13 figures, 3 tables

Stress state variations among the clay and limestone formations of the molasse basin of Northern Switzerland

International Nuclear Information System (INIS)

Vietor, Tim; Mueller, Herwig; Frieg, Bernd; Klee, Gerd

2012-01-01

principle stress can be considered to be in the range of a few meters at most. The fracture orientations have been determined with the help of geophysical logging runs that compare the borehole wall image before and after the stress measurements. In some cases additional impression packer tests have been performed. The fracture orientations consistently indicate a minimum horizontal stress direction that strikes roughly east-west. This orientation is in line with the orientations of borehole breakouts in this and other boreholes in the Molasse Basin and moment tensor solutions of pre-alpine earthquakes in the region. The vertical distribution of the orientations along the borehole does not hint towards a stress decoupling at the level of the Triassic evaporites. The vertical profile of the stress magnitudes shows that over the entire section the minimum horizontal stresses are smaller than the vertical stresses (the latter have been calculated from the overburden using average density values). Small minimum horizontal stresses that reach only 0.6 times the overburden load have been measured in the massive limestone units and in the basement. In contrast, values around 0.8 to 0.9 have been determined in the marls and shales. A similar stress distribution has been previously demonstrated in the Benken exploration borehole 10 km away. The observations indicate that the variations of the stress magnitudes between the different rock units are closely related to their strength. (authors)

Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

International Nuclear Information System (INIS)

Vallee, Christophe; Hoehne, Thomas; Prasser, Horst-Michael; Suehnel, Tobias

2008-01-01

For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Dresden-Rossendorf (FZD). The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronised with the high-speed camera system. CFD post-test simulations of stratified flows were performed using the code ANSYS CFX. The Euler-Euler two fluid model with the free surface option was applied on grids of minimum 4 x 10 5 control volumes. The turbulence was modelled separately for each phase using the k-ω-based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow

Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

International Nuclear Information System (INIS)

Vallee, Christophe; Hohne, Thomas; Prasser, Horst-Michael; Suhnel, Tobias

2007-01-01

For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Rossendorf. The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronized with the high-speed camera system. CFD post test simulations of stratified flows were performed using the code ANSYS CFX. The Euler- Euler two fluid model with the free surface option was applied on grids of minimum 4.10 5 control volumes. The turbulence was modelled separately for each phase using the k-ω based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow. (authors)

Experimental investigation and CFD simulation of horizontal stratified two-phase flow phenomena

Energy Technology Data Exchange (ETDEWEB)

Vallee, Christophe [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany)], E-mail: c.vallee@fzd.de; Hoehne, Thomas; Prasser, Horst-Michael; Suehnel, Tobias [Forschungszentrum Dresden-Rossendorf e.V., Dresden (Germany)

2008-03-15

For the investigation of stratified two-phase flow, two horizontal channels with rectangular cross-section were built at Forschungszentrum Dresden-Rossendorf (FZD). The channels allow the investigation of air/water co-current flows, especially the slug behaviour, at atmospheric pressure and room temperature. The test-sections are made of acrylic glass, so that optical techniques, like high-speed video observation or particle image velocimetry (PIV), can be applied for measurements. The rectangular cross-section was chosen to provide better observation possibilities. Moreover, dynamic pressure measurements were performed and synchronised with the high-speed camera system. CFD post-test simulations of stratified flows were performed using the code ANSYS CFX. The Euler-Euler two fluid model with the free surface option was applied on grids of minimum 4 x 10{sup 5} control volumes. The turbulence was modelled separately for each phase using the k-{omega}-based shear stress transport (SST) turbulence model. The results compare very well in terms of slug formation, velocity, and breaking. The qualitative agreement between calculation and experiment is encouraging and shows that CFD can be a useful tool in studying horizontal two-phase flow.

Work ability and stress in a bus transportation company in Belo Horizonte, Brazil.

Science.gov (United States)

Sampaio, Rosana Ferreira; Coelho, Cecília Martins; Barbosa, Fábio Bonfim; Mancini, Marisa Cotta; Parreira, Verônica Franco

2009-01-01

Demographic, occupational and psychosocial characteristics affect the health and occupational performance of workers. The objective of the present study was to elaborate a profile of the work ability and factors that affect it in a bus transportation company in Belo Horizonte, Brazil. The instruments used included a socio-demographic and occupational questionnaire, the Work Ability Index and the Job Stress Scale. Demographic information revealed that 85.7% of the 126 employees of the company were active workers, 98% were males, with an average of 39 years of age (SD= 10) and 79 months working in the company (SD= 68); more than half reported having a low schooling level. In terms of personal habits, 88% were exposed to one or more risk factors, especially a sedentary lifestyle. The average strain value (as a consequence of stress) was 0.78 (SD= 0.2) and 75.3% reported episodes of violence at the workplace. The work ability was good to excellent among 89% of the workers. Results from the logistic regression analysis showed that strain was the only significant variable in relation to the Work Ability Index, (estimated odds ratio of 0.02). The results suggest that psychosocial factors presented the greatest association with work ability, and preventive and/or corrective measures should be implemented.

Horizontal stresses below two agricultural vehicles

DEFF Research Database (Denmark)

Lamande, Mathieu André Maurice; Munkholm, Lars Juhl; Nielsen, Janne Aalborg

Abstract Deformation of the pore system in the subsoil due to mechanical stress applied by agricultural machinery is persistent for at least decades. Application of normal stress exceeding subsoil strength leads to a reduction of capacity soil properties (i.e. air-filled porosity) by compaction...... below the edge of tires. Stress distribution at the tire/soil contact is not uniform. Dimensions and inflation pressure are key factors for the ability of agricultural tires to distribute the wheel load. Our hypothesis was that the risk of shearing increases with the tire inflation pressure...

In situ stress and pore pressure in the Kumano Forearc Basin, offshore SW Honshu from downhole measurements during riser drilling

Science.gov (United States)

Saffer, D. M.; Flemings, P. B.; Boutt, D.; Doan, M.-L.; Ito, T.; McNeill, L.; Byrne, T.; Conin, M.; Lin, W.; Kano, Y.; Araki, E.; Eguchi, N.; Toczko, S.

2013-05-01

situ stress and pore pressure are key parameters governing rock deformation, yet direct measurements of these quantities are rare. During Integrated Ocean Drilling Program (IODP) Expedition #319, we drilled through a forearc basin at the Nankai subduction zone and into the underlying accretionary prism. We used the Modular Formation Dynamics Tester tool (MDT) for the first time in IODP to measure in situ minimum stress, pore pressure, and permeability at 11 depths between 729.9 and 1533.9 mbsf. Leak-off testing at 708.6 mbsf conducted as part of drilling operations provided a second measurement of minimum stress. The MDT campaign included nine single-probe (SP) tests to measure permeability and in situ pore pressure and two dual-packer (DP) tests to measure minimum principal stress. Permeabilities defined from the SP tests range from 6.53 × 10-17 to 4.23 × 10-14 m2. Pore fluid pressures are near hydrostatic throughout the section despite rapid sedimentation. This is consistent with the measured hydraulic diffusivity of the sediments and suggests that the forearc basin should not trap overpressures within the upper plate of the subduction zone. Minimum principal stresses are consistently lower than the vertical stress. We estimate the maximum horizontal stress from wellbore failures at the leak-off test and shallow MDT DP test depths. The results indicate a normal or strike-slip stress regime, consistent with the observation of abundant active normal faults in the seaward-most part of the basin, and a general decrease in fault activity in the vicinity of Site C0009.

Effective stresses and shear failure pressure from in situ Biot's coefficient, Hejre Field, North Sea

DEFF Research Database (Denmark)

Regel, Jeppe Bendix; Orozova-Bekkevold, Ivanka; Andreassen, Katrine Alling

2017-01-01

, is significantly different from 1. The log-derived Biot's coefficient is above 0.8 in the Shetland Chalk Group and in the Tyne Group, and 0.6-0.8 in the Heno Sandstone Formation. We show that the effective vertical and horizontal stresses obtained using the log-derived Biot's coefficient result in a drilling......We propose a combination of Biot's equations for effective stress and the expression for shear failure in a rock to obtain an expression for minimum pore pressure in a stable vertical well bore. We show that a Biot's coefficient calculated from logging data in the Hejre Field, North Sea...

Possible mechanism of horizontal overpressure generation of the Khibiny, Lovozero, and Kovdor ore clusters on the Kola Peninsula

Science.gov (United States)

Rebetsky, Yu. L.; Sim, L. A.; Kozyrev, A. A.

2017-07-01

The paper discusses questions related to the generation of increasing crustal horizontal compressive stresses compared to the idea of the standard gravitational state at the elastic stage or even from the prevalence of horizontal compression over vertical stress equal to the lithostatic pressure. We consider a variant of superfluous horizontal compression related to internal lithospheric processes occurrin in the crust of orogens, shields, and plates. The vertical ascending movements caused by these motions at the sole of the crust or the lithosphere pertain to these and the concomitant exogenic processes giving rise to denudation and, in particular, to erosion of the surfaces of forming rises. The residual stresses of the gravitational stressed state at the upper crust of the Kola Peninsula have been estimated for the first time. These calculations are based on the volume of sediments that have been deposited in Arctic seas beginning from the Mesozoic. The data speak to the possible level of residual horizontal compressive stresses up to 90 MPa in near-surface crustal units. This estimate is consistent with the results of in situ measurements that have been carried out at the Mining Institute of the Kola Science Center, Russian Academy of Sciences (RAS), for over 40 years. It is possible to forecast the horizontal stress gradient based on depth using our concept on the genesis of horizontal overpressure, and this forecasting is important for studying the formation of endogenic deposits.

Stress estimation around the survey wells in Hanshin-Awaji area by means of AE/DR and DSCA experiments; AE/DR ho to DSCA ho ni yoru Hanshin Awaji chiiki chosa kui shuhen no chikaku oryoku sokutei

Energy Technology Data Exchange (ETDEWEB)

Ito, H; Kuwahara, Y; Nishizawa, O [Geological Survey of Japan, Tsukuba (Japan); Yamamoto, K [Tohoku University, Sendai (Japan). Faculty of Science; Sano, O [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Yokoyama, T; Kudo, R [OYO Corp., Tokyo (Japan); Xue, Z [Kiso-Jiban Consultants Co. Ltd., Tokyo (Japan)

1996-05-01

A total of 5 wells were excavated in the Hanshin-Awaji area (Ikeda, Takarazuka, Tarumi, Hirabayashi and Ikunami) to collect the core samples, which were analyzed by the AE/DR and DSCA methods to determine crustal stresses. For the AE/DR analysis, the core sample was cut in the vertical direction, and in the horizontal direction at intervals of 45{degree}. The sample of unknown orientation was provided with a datum line common for both methods, to compare the results by these methods. A load was applied to the sample, provided with an AE sensor and strain gauge on the sides, in the longitudinal direction. For the DSCA analysis, the core sample was cut into a cube having a side length of 33mm, with a pair of planes directed in parallel to the datum line. A total of 18 strain gauges, 10mm in gauge length, were attached to the cube. The AE/DR analysis gave the maximum and minimum principal stresses in the horizontal plane and stresses in the vertical direction, whereas the DSCA the maximum, intermediate and minimum principal stresses. 3 refs., 7 figs.

Economic Integration and Quality Standards in a Duopoly Model with Horizontal and Vertical Product Differentiation

DEFF Research Database (Denmark)

Nielsen, Jørgen Ulff-Møller; Hansen, Jørgen Drud

This paper examines the effects of trade barriers on quality levels in a duopoly model for two countries with one producer in each country. The products are both vertically and horizontally differentiated. In absence of quality regulation, the two producers determine prices and quality levels...... standards are also ambiguous depending on the parameters of the model. Keywords: Vertical product differentiation; horizontal product differentiation; market integration; duopoly; minimum quality standard. JEL: F12, F13, F14....... product. On the unregulated markets, integration increases welfare in both countries if they are almost of similar size. However, if the countries are very asymmetrical with respect to size, market integration may harm welfare in the large country. Welfare effects by introduction of minimum quality...

Stress rotation along pre-Cenozoic basement structures

Science.gov (United States)

Reiter, K.; Heidbach, O.; Henk, A.

2017-12-01

-German Crystalline High based on this presumption. 1. The magnitude of SHmax and the minimum horizontal stress (Shmin) in the region is close by, allowing local stress rotation. 2. The stiffness contrast perpendicular to the strike of the Variscan basement structures is large enough as stress source to cause significant rotation of the stress pattern.

Erosion characteristics and horizontal variability for small erosion depths in the Sacramento-San Joaquin River Delta, California, USA

Science.gov (United States)

Schoellhamer, David H.; Manning, Andrew J.; Work, Paul A.

2017-01-01

Erodibility of cohesive sediment in the Sacramento-San Joaquin River Delta (Delta) was investigated with an erosion microcosm. Erosion depths in the Delta and in the microcosm were estimated to be about one floc diameter over a range of shear stresses and times comparable to half of a typical tidal cycle. Using the conventional assumption of horizontally homogeneous bed sediment, data from 27 of 34 microcosm experiments indicate that the erosion rate coefficient increased as eroded mass increased, contrary to theory. We believe that small erosion depths, erosion rate coefficient deviation from theory, and visual observation of horizontally varying biota and texture at the sediment surface indicate that erosion cannot solely be a function of depth but must also vary horizontally. We test this hypothesis by developing a simple numerical model that includes horizontal heterogeneity, use it to develop an artificial time series of suspended-sediment concentration (SSC) in an erosion microcosm, then analyze that time series assuming horizontal homogeneity. A shear vane was used to estimate that the horizontal standard deviation of critical shear stress was about 30% of the mean value at a site in the Delta. The numerical model of the erosion microcosm included a normal distribution of initial critical shear stress, a linear increase in critical shear stress with eroded mass, an exponential decrease of erosion rate coefficient with eroded mass, and a stepped increase in applied shear stress. The maximum SSC for each step increased gradually, thus confounding identification of a single well-defined critical shear stress as encountered with the empirical data. Analysis of the artificial SSC time series with the assumption of a homogeneous bed reproduced the original profile of critical shear stress, but the erosion rate coefficient increased with eroded mass, similar to the empirical data. Thus, the numerical experiment confirms the small-depth erosion hypothesis. A linear

Defining in-situ stress magnitude and the responses of geology to stress anisotropy in heterogeneous lithologies for the United Kingdom

Science.gov (United States)

Kingdon, A.; Fellgett, M. W.; Williams, J. D. O.

2017-12-01

Exploitation of shale gas in the USA has led to interest in similar UK deposits. After tremors at the Preese Hall well in 2011, the process of hydraulic fracturing has become contentious. In-situ stress orientation controls the direction that fractures propagate from a well. World Stress Map (WSM) data coverage for the UK has historically been sparse. Improvements to the stress orientations for the UK are vital for reducing risk levels of induced seismicity. In some offshore basins, maximum horizontal stress (SHMax) is sub-parallel to major inverted Permo-Triassic faults, episodically reactivated during the Cenozoic, indicating a degree of structural control. Understanding for UK stress magnitude has been poor. Data for Northern England has been augmented with new estimates of vertical stress (Sv), minimum horizontal stress (Shmin) and pore pressure, focussed on potentially prospective basins east and west of the Pennines. Calculated values combined with legacy hydraulic fracturing and overcoring data show vertical stress gradients vary from 23 to 26 MPa/Km-1. Cheshire and Scotland show higher Shmin values by 2 MPa/Km-1 compared to Yorkshire and South East England. SHMax values exceeds the Sv which in turn exceeds Shmin indicating a predominantly strike slip environment. Pore pressure appears to be uniformly hydrostatic across the studied regions. There is some evidence above 1200 m depth of reverse faulting in igneous rocks in Cornwall, Leicestershire and Cumbria. Analysis of borehole imaging for the lithologically heterogeneous Carboniferous Coal Measures, highlights variability failure modes over confined vertical intervals. Breakouts are disproportionately located in "seatearths", palaeosols located stratigraphically beneath coal seams. Drilling induced tensile fractures are located within close proximity in overbank silt/clay facies and relatively massive channel sands that typically over and underlie coal deposits. Strength tests show that breakouts occur in

Investigation of stress in a circular tunnel due to overburden and thermal loading of horizontally placed 21 PWR multi purpose canisters

International Nuclear Information System (INIS)

Kandalaft-Ladkany, N.; Wyman, R.V.

1994-01-01

The drift of a High Level Nuclear Waste (HLNW) Repository were subjected to 2-D thermal loading resulting from the horizontal emplacement of 125 Ton Multi-Purpose Canisters (MPC). Ten 2-D temperature profiles, resulting from 57 Kw/acre and 114 Kw/acre thermal loading conditions, were used in a finite element analysis of the drift; in which a quadrant of the drift and surrounding rock ±100m above and below the drift were modeled. Our analysis shows that the 114 Kw/acre thermal loading results in compressive stresses around the drift, 60 years after emplacement, that exceed the unconfined compressive strength of the TSW tuff analyzed. Stresses resulting from a 57 Kw/acre thermal loading are within the acceptable limit in tunnel rock. A parametric analysis of the invert backfill material showed that Young's modulus for the invert backfill should closely match that of the surrounding unconfined rock in the tunnel in order to prevent an unacceptable stress rise in both rock and backfill

Rock stress measurements in the deep boreholes at Kuhmo, Hyrynsalmi, Sievi, Eurajoki and Konginkangas

International Nuclear Information System (INIS)

Klasson, H.; Leijon, B.

1990-11-01

Hydraulic fracturing rock stress measurements, conducted in five boreholes are presented. The boreholes are located in different site investigation areas in Finland: Kuhmo-Romuvaara, Hyrynsalmi-Veitsivaara, Sievi-Syyry, Eurajoki-Olkiluoto and Konginkangas-Kivetty. The aim of the measurements was to provide rock stress data, forming input to the site selection process for an underground facility for disposal of high level radioactive waste from the Olkiluoto Nuclear Power Plant. A summary is given of the theoretical background to the hydrofracturing method, whilst the equipment and experimental procedures used in the present case are described in more detail. All results obtained are presented and subjected to critical discussion. The final stress parameters evaluated are magnitudes and directions of the maximum and minimum horizontal stresses. Testing was successfully completed according to the clan at Syyry, Olkiluoto and Kivetty. Testing was partly successful at Romuvaara but unsuccessful in the borehole at Veitsivaara

Modified theoretical minimum emittance lattice for an electron storage ring with extreme-low emittance

Directory of Open Access Journals (Sweden)

Yi Jiao

2011-05-01

Full Text Available In the continuing efforts to reduce the beam emittance of an electron storage ring composed of theoretical minimum emittance (TME lattice, down to a level of several tens of picometers, nonlinear dynamics grows to be a great challenge to the performance of the storage ring because of the strong sextupoles needed to compensate for its large global natural chomaticities coupled with its small average dispersion function. To help in dealing with the challenge of nonlinear optimization, we propose a novel variation of theoretical minimum emittance (TME lattice, named as “modified-TME” lattice, with minimal emittance about 3 times of the exact theoretical minimum, while with more compact layout, lower phase advance per cell, smaller natural chromaticities, and more relaxed optical functions than that in a TME cell, by using horizontally defocusing quadrupole closer to the dipole or simply combined-function dipole with horizontally defocusing gradient. We present approximate scaling formulas to describe the relationships of the design parameters in a modified-TME cell. The applications of modified-TME lattice in the PEP-X storage ring design are illustrated and the proposed lattice appears a good candidate for synchrotron radiation light source with extremely low emittance.

Rivulet flow round a horizontal cylinder subject to a uniform surface shear stress

KAUST Repository

Paterson, C.

2014-09-14

© 2014 © The Author, 2014. Published by Oxford University Press; all rights reserved. For Permissions, please email: journals.permissions@oup.com. The steady flow of a slowly varying rivulet with prescribed flux in the azimuthal direction round a large stationary horizontal cylinder subject to a prescribed uniform azimuthal surface shear stress is investigated. In particular, we focus on the case where the volume flux is downwards but the shear stress is upwards, for which there is always a solution corresponding to a rivulet flowing down at least part of one side of the cylinder. We consider both a rivulet with constant non-zero contact angle but slowly varying width (that is, de-pinned contact lines) and a rivulet with constant width but slowly varying contact angle (that is, pinned contact lines), and show that they have qualitatively different behaviour. When shear is present, a rivulet with constant non-zero contact angle can never run all the way from the top to the bottom of the cylinder, and so we consider the scenario in which an infinitely wide two-dimensional film of uniform thickness covers part of the upper half of the cylinder and \\'breaks\\' into a single rivulet with constant non-zero contact angle. In contrast, a sufficiently narrow rivulet with constant width can run all the way from the top to the bottom of the cylinder, whereas a wide rivulet can do so only if its contact lines de-pin, and so we consider the scenario in which the contact lines of a wide rivulet de-pin on the lower half of the cylinder.

Mechanical and mathematical models of multi-stage horizontal fracturing strings and their application

Directory of Open Access Journals (Sweden)

Zhanghua Lian

2015-03-01

Full Text Available Multi-stage SRV fracturing in horizontal wells is a new technology developed at home and abroad in recent years to effectively develop shale gas or low-permeability reservoirs, but on the other hand makes the mechanical environment of fracturing strings more complicated at the same time. In view of this, based on the loading features of tubing strings during the multi-stage fracturing of a horizontal well, mechanical models were established for three working cases of multiple packer setting, open differential-pressure sliding sleeve, and open ball-injection sliding sleeve under a hold-down packer. Moreover, mathematical models were respectively built for the above three cases. According to the Lame formula and Von Mises stress calculation formula for the thick-walled cylinder in the theory of elastic mechanics, a mathematical model was also established to calculate the equivalent stress for tubing string safety evaluation when the fracturing string was under the combined action of inner pressure, external squeezing force and axial stress, and another mathematical model was built for the mechanical strength and safety evaluation of multi-stage fracturing strings. In addition, a practical software was developed for the mechanical safety evaluation of horizontal well multi-stage fracturing strings according to the mathematical model developed for the mechanical calculation of the multi-packer string in horizontal wells. The research results were applied and verified in a gas well of Tahe Oilfield in the Tarim Basin with excellent effects, providing a theoretical basis and a simple and reliable technical means for optimal design and safety evaluation of safe operational parameters of multi-stage fracturing strings in horizontal wells.

Lithology-dependent In Situ Stress in Heterogeneous Carbonate Reservoirs

Science.gov (United States)

Pham, C. N.; Chang, C.

2017-12-01

Characterization of in situ stress state for various geomechanical aspects in petroleum development may be particularly difficult in carbonate reservoirs in which rock properties are generally heterogeneous. We demonstrate that the variation of in situ stress in highly heterogeneous carbonate reservoirs is closely related to the heterogeneity in rock mechanical property. The carbonate reservoir studied consists of numerous sequential layers gently folded, exhibiting wide ranges of porosity (0.01 - 0.29) and Young's modulus (25 - 85 GPa) depending on lithology. Wellbore breakouts and drilling-induced tensile fractures (DITFs) observed in the image logs obtained from several wells indicate that the in situ state of stress orientation changes dramatically with depth and location. Even in a wellbore, the azimuth of the maximum horizontal stress changes by as much as 60° within a depth interval of 500 m. This dramatic change in stress orientation is inferred to be due to the contrast in elastic properties between different rock layers which are bent by folding in the reservoir. The horizontal principal stress magnitudes are constrained by back-calculating stress conditions necessary to induce the observed wellbore failures using breakout width and the presence of DITFs. The horizontal stresses vary widely, which cannot be represented by a constant stress gradient with depth. The horizontal principal stress gradient increases with Young's modulus of layer monotonically, indicating that a stiffer layer conveys a higher horizontal stress. This phenomenon can be simulated using a numerical modelling, in which the horizontal stress magnitudes depend on stiffness of individual layers although the applied far-field stress conditions are constant. The numerical results also suggest that the stress concentration at the wellbore wall is essentially higher in a stiffer layer, promoting the possibility of wellbore breakout formation. These results are in agreement with our

Horizontal-view interferometer on TEXT-Upgrade

International Nuclear Information System (INIS)

Jiang, Y.; Brower, D.L.

1994-01-01

The first experimental results from the horizontal-view, multichannel, heterodyne FIR interferometer system on TEXT-Upgrade are reported. The system employs parabolic beam-expansion optics and a 15 cm array with minimum channel spacing of 1.5 cm. Profiles of the plasma electron density will be presented. In addition, small-amplitude density perturbations resulting from sawteeth and tearing modes are examined. Due to the double-pass of the laser beam through the plasma and the large distance of the detector array [2.5 m] from the plasma, refractive effects must be addressed for densities greater than 2 x 10 13 cm -3 . A ray tracing code is developed to correct the measured profiles

Volume fracturing of deep shale gas horizontal wells

Directory of Open Access Journals (Sweden)

Tingxue Jiang

2017-03-01

Full Text Available Deep shale gas reservoirs buried underground with depth being more than 3500 m are characterized by high in-situ stress, large horizontal stress difference, complex distribution of bedding and natural cracks, and strong rock plasticity. Thus, during hydraulic fracturing, these reservoirs often reveal difficult fracture extension, low fracture complexity, low stimulated reservoir volume (SRV, low conductivity and fast decline, which hinder greatly the economic and effective development of deep shale gas. In this paper, a specific and feasible technique of volume fracturing of deep shale gas horizontal wells is presented. In addition to planar perforation, multi-scale fracturing, full-scale fracture filling, and control over extension of high-angle natural fractures, some supporting techniques are proposed, including multi-stage alternate injection (of acid fluid, slick water and gel and the mixed- and small-grained proppant to be injected with variable viscosity and displacement. These techniques help to increase the effective stimulated reservoir volume (ESRV for deep gas production. Some of the techniques have been successfully used in the fracturing of deep shale gas horizontal wells in Yongchuan, Weiyuan and southern Jiaoshiba blocks in the Sichuan Basin. As a result, Wells YY1HF and WY1HF yielded initially 14.1 × 104 m3/d and 17.5 × 104 m3/d after fracturing. The volume fracturing of deep shale gas horizontal well is meaningful in achieving the productivity of 50 × 108 m3 gas from the interval of 3500–4000 m in Phase II development of Fuling and also in commercial production of huge shale gas resources at a vertical depth of less than 6000 m.

A mechanistic determination of horizontal flow regime bound using void wave celerity

Energy Technology Data Exchange (ETDEWEB)

Park, J.W. [Ajou Univ., Suwon (Korea, Republic of)

1995-09-01

The two-phase flow regime boundaries in a horizontal channel has been investigated by using the behavior of the second order void wave celerities. The average two-fluid model has been constituted with closure relations for horizontally stratified and bubbly flows. A vapor phase turbulent stress model for a smooth interface geometry has been included. It is found that the second order waves (i.e., eigenvalues) propagate in opposite direction with almost the same speed when the liquid phase is stationary. Using the well-posedness limit of the two-phase system, the dispersed-stratified flow regime boundary has been modeled. Two-phase Froude number has been theoretically found to be a convenient parameter in quantifying the flow regime boundary as a function of the void fraction. It is found that interaction between void wave celerities become stronger as the two-phase Froude number is reduced. This result should be interpreted as that gravity and the relative velocity are key parameters in determining flow regime boundaries in a horizontal flow. The influence of the vapor phase turbulent stress found to stabilize the flow stratification. This study clearly shows that the average two-fluid model is very effective for a mechanistic determination of horizontal flow regimes if appropriate closure relations are developed.

A mechanistic determination of horizontal flow regime bound using void wave celerity

International Nuclear Information System (INIS)

Park, J.W.

1995-01-01

The two-phase flow regime boundaries in a horizontal channel has been investigated by using the behavior of the second order void wave celerities. The average two-fluid model has been constituted with closure relations for horizontally stratified and bubbly flows. A vapor phase turbulent stress model for a smooth interface geometry has been included. It is found that the second order waves (i.e., eigenvalues) propagate in opposite direction with almost the same speed when the liquid phase is stationary. Using the well-posedness limit of the two-phase system, the dispersed-stratified flow regime boundary has been modeled. Two-phase Froude number has been theoretically found to be a convenient parameter in quantifying the flow regime boundary as a function of the void fraction. It is found that interaction between void wave celerities become stronger as the two-phase Froude number is reduced. This result should be interpreted as that gravity and the relative velocity are key parameters in determining flow regime boundaries in a horizontal flow. The influence of the vapor phase turbulent stress found to stabilize the flow stratification. This study clearly shows that the average two-fluid model is very effective for a mechanistic determination of horizontal flow regimes if appropriate closure relations are developed

Hydraulic fracturing stress measurements at Yucca Mountain, Nevada, and relationship to the regional stress field

International Nuclear Information System (INIS)

Stock, J.M.; Healy, J.H.; Hickman, S.H.; Zoback, M.D.

1985-01-01

Hydraulic fracturing stress measurements and acoustic borehole televiewer logs were run in holes USW G-1 and USW G-2 at Yucca Mountain as part of the Nevada Nuclear Waste Storage Investigations for the U. S. Department of Energy. Eight tests in the saturated zone, at depths from 646 to 1288 m, yielded values of the least horizontal stress S/sub h/ that are considerably lower than the vertical principal stress S/sub v/. In tests for which the greatest horizontal principal stress S/sub H/ could be determined, it was found to be less than S/sub v/, indicating a normal faulting stress regime. The borehole televiewer logs showed the presence of long (in excess of 10 m), vertical, drilling-induced fractures in the first 300 m below the water table. These are believed to form by the propagation of small preexisting cracks under the excess downhole fluid pressures (up to 5.2 MPa) applied during drilling. The presence of these drilling-induced hydrofractures provides further confirmation of the low value of the least horizontal stresses. A least horizontal principal stress direction of N60 0 W--N65 0 W is indicated by the orientation of the drilling-induced hydrofractures (N25 0 E--N30 0 E), and the orientation of stress-induced well bore breakouts in the lower part of USW G-2 (N65 0 W). This direction is in good agreement with indicators of stress direction from elsewhere at the Nevada Test Site. The observed stress magnitudes and directions were examined for the possibility of slip on preexisting faults. Using these data, the Coulomb criterion for frictional sliding suggests that for coefficients of friction close to 0.6, movement on favorably oriented faults could be expected

Test with different stress measurement methods in two orthogonal bore holes in Aespoe HRL

Energy Technology Data Exchange (ETDEWEB)

Janson, Thomas; Stigsson, Martin [Golder Associates AB, Stockholm (Sweden)

2002-12-01

conclusions have been drawn, based on the stress measurements and deeper investigations: The following stress state is obtained at the target volume at about -455 m. The minimum horizontal stress is between 10 and 13 MPa, which is lower than the theoretical vertical stress. The maximum horizontal stress is 24 {+-}5 MPa, most likely within the upper range. The vertical stress is between 15 and 20 MPa, most probably is this value only local due to the presence of a nearby fracture. The local disturbance of the stress field in the rock mass, due to discontinuities has been demonstrated. This also indicates one of the problems with stress measurements in boreholes. In the area with significant anisotropic stress conditions all the tested methods were able to determine the orientation of the principal major horizontal stress within {+-} 10 deg. The microscopy investigations confirm two sets of microcracks in the overcored core. One set was parallel and near the bore hole bottom and one set was perpendicular to the bottom and located a bit away from the hole bottom. The results from the overcoring may be influenced by microcracks, causing additional non-elastic strains. Only the results from the DDGS seem to have been influenced, indicating that the hollow cylinder of a 3D stress cell may be less sensitive for stress induced sample disturbance than core samples from the 2D Door stopper cell. The determination of Young's modulus in a medium grained crystalline rock with heterogeneity may not be trivial using core samples. The results from the determination influence the calculated stresses. Hydraulic fracturing most likely measures the most correct value of the minimum horizontal stress, provided that the induced fracture is aligned with the borehole. If the rock behaves reasonable elastic the overcoring methods provide stress magnitudes with an uncertainty of 15-20%. It seems likely that the overcoring methods may overestimate the stress magnitudes at large depth, due to the

Present-day stress magnitude at depth from leak-off tests in Italy

Science.gov (United States)

Mariucci, M. T.; Montone, P.; Pierdominici, S.

2012-04-01

We present new results from the analysis of leak-off tests, performed in deep oil wells in Italy, to characterize the present-day stress magnitude and regime in the crust. In the last years we have collected a large number of data (more than 500) from different stress indicators, mainly borehole breakouts, earthquake focal mechanisms and fault data, which provided information on the present-day stress orientations. In some areas the tectonic regime has been inferred either from fault plane solutions of M≥4 earthquakes or from stress inversions of smaller earthquakes. Where seismicity lacks, the regime is not well constrained and little or no information on the magnitude of the crustal stresses is available. In order to improve our knowledge in stress regime and its magnitude in Italy, in this work we use the leak-off test technique. Each test is performed at the bottom of an open hole by sealing off a section and then slowly pressurizing with a fluid until hydraulic tensile fractures develop. The minimum horizontal stress is inferred by leak-off pressure record, the vertical stress is computed by rock density data and the maximum horizontal stress is estimated applying a specific formula from the literature. Thanks to ENI S.p.A. (Italian oil company), that kindly provided new well data, we have been able to perform a critical review of our preliminary calculations and to enhance our previous results concerning stress magnitudes. Totally, we have analyzed 192 leak-off tests at depth between 200 and 5400m (average 1800m). In particular, wells are located along the Italian peninsula and in Sicily: most of them are in the Po Plain and along the Apenninic foredeep; few are in southern Apenninic belt and a few tens are in Sicily. After an accurate selection of the most robust results, we better characterize the Italian stress regime at depth.

Evaluation of Stress Distribution of Mini Dental Implant-Supported Overdentures in Complete Cleft Palate Models: A Three-Dimensional Finite Element Analysis Study.

Science.gov (United States)

Soğancı, Gökçe; Yazıcıoğlu, Hüseyin

2016-01-01

Mini dental implants could be an alternative treatment method for prosthetic treatment of edentulous cleft palate. The aim of this study was to analyze stress distribution around the cortical bone and different plans using a varied number of mini dental implants in edentulous unilateral complete cleft palates. Three edentulous maxillary models were modified to create unilateral complete cleft palates. Mini dental implants (2.4 × 15 mm) were located as two mini implants at the premolar region, four mini implants at the premolar and molar region, and six mini implants at the first premolar, second premolar, and first molar regions in the models, respectively. Mucosa, o-ring/ball attachments, and overdentures were simulated. Vertical and horizontal loads of 100 N were applied on both the right and left molar teeth of the overdenture for each model. Maximum and minimum principal stress values and the distribution at cortical bone around the implants and cleft palates were evaluated by finite element analysis. Stress values under vertical loads were lower than values under horizontal loadings for all models. Stress values were found to be lower in the first model than in the second and third models. The highest stress values were found around implants in the second model. The unilateral feature of a complete cleft pattern affected the stress distribution. Stresses occured mostly around implants when the overdenture was supported by six implants; however, the stress distribution around implants was low with two implants because of tissue support.

Exploration of joint systems and major horizontal stress direction in HDR drillholes of the Soultz site (Alsace, France)

Energy Technology Data Exchange (ETDEWEB)

Genter, A [BRGM/GIG, Orleans (France); Tenzer, H [Stadtwerke Bad Urach (Germany)

1997-12-01

Borehole imaging logs enable continuous recording of natural and artificial planar discontinuities on the drillhole wall and data of the drillhole geometry to be made. Efforts were made to resolve the orientation and characterization of the natural joint system, the active fault pattern, the alteration zones, the orientation of microcracks and the direction of maximum horizontal stress. Intense logging operations and measurements were carried out in the HDR drillholes GPK1 and EPS1 between 1000 and 3600 m depth in the Muschelkalk, Bunter and Granite at Soultz sous Forets. With the help of investigations on subvertical fractures the orientation of the maximum horizontal stress direction was determined as N175 E{+-}17 . These results are consistent with previous investigations performed in the horeholes GPK-1 and EPS-1. (orig./AKF) [Deutsch] Bohrlochmessungen mit dem akustschen Borehole Televiewer und elektrischen Formation MicroScanner (Imager) sowie dem Azimuthal Resistivity Imager und verschiedenen Sonic-Sonden ermoeglichen eine kontinuierliche Aufnahme sowohl von natuerlichen und kuenstlich erzeugten planaren Diskontinuitaeten an der Bohrlochwand als auch der Bohrlochgeometrie. Es wurden die Orientierung und Charakterisierung des natuerlichen Kluftsystems, das aktive Stoerungsmuster, die Alterationszonen, die Orientierung von Mikrorissen und die Orientierung der maximalen horizontalen Hauptspannungsrichtung ermittelt. Die Verfuegbarkeit von Strukturdaten aus Bohrloechern durch Bohrlochmessungen und hydraulischen Testen ermoeglicht die Bestimmung von hydraulisch aktiven Klueften und deren Beziehung zum regionalen Spannungsfeld. Mit Hilfe spezieller Bohrloch-Logs wurden die Orientierung und Haeufigkeit planarer Diskontinuitaeten und ihre scheinbare Oeffnungsweite sowie die Vorzugsrichtung der verschiedenen scheinbaren Weiten bestimmt. Innerhalb des gemeinsamen europaeischen Hot-Dry-Rock-Geothermal-Forschungsprogramms wurden vielfaeltige Bohrlochmessungen in den

Statistical Estimation of Subgrade Reaction Coefficient For Horizontally Loaded Piles

International Nuclear Information System (INIS)

Honjo, Yusuke; Zaika, Yulvi; Pokharel, Gyaneswor

2002-01-01

Appropriate horizontal subgrade reaction (k h ) is required to evaluate stress and displacement in horizontal loading pile. In order to obtain more accurate prediction of pile behavior, statistical analysis is employed. Based on 21 data set gathered on horizontal loading piles, inverse analysis and regression analysis are carried out. The main value and uncertainty are obtained by inverse analysis, could be employed in the regression analysis. The relationship between the lateral resistant constant (k c ) and SPT N value takes into account in correlated and uncorrelated condition. The results are compared with Port and Harbor Technical Research Institute (JPHA, 1999) and Japan Highway Bridge Specification IV (JRA, 1996). The computed values are found to be very close to the JPHA line and within the range of JRA lines in diameter 0.5 m and 2 m

Characterization of horizontal air–water two-phase flow

Energy Technology Data Exchange (ETDEWEB)

Kong, Ran; Kim, Seungjin, E-mail: skim@psu.edu

2017-02-15

Highlights: • A visualization study is performed to develop flow regime map in horizontal flow. • Database in horizontal bubbly flow is extended using a local conductivity probe. • Frictional pressure drop analysis is performed in horizontal bubbly flow. • Drift flux analysis is performed in horizontal bubbly flow. - Abstract: This paper presents experimental studies performed to characterize horizontal air–water two-phase flow in a round pipe with an inner diameter of 3.81 cm. A detailed flow visualization study is performed using a high-speed video camera in a wide range of two-phase flow conditions to verify previous flow regime maps. Two-phase flows are classified into bubbly, plug, slug, stratified, stratified-wavy, and annular flow regimes. While the transition boundaries identified in the present study compare well with the existing ones (Mandhane et al., 1974) in general, some discrepancies are observed for bubbly-to-plug/slug, and plug-to-slug transition boundaries. Based on the new transition boundaries, three additional test conditions are determined in horizontal bubbly flow to extend the database by Talley et al. (2015a). Various local two-phase flow parameters including void fraction, interfacial area concentration, bubble velocity, and bubble Sauter mean diameter are obtained. The effects of increasing gas flow rate on void fraction, bubble Sauter mean diameter, and bubble velocity are discussed. Bubbles begin to coalesce near the gas–liquid layer instead of in the highly packed region when gas flow rate increases. Using all the current experimental data, two-phase frictional pressure loss analysis is performed using the Lockhart–Martinelli method. It is found that the coefficient C = 24 yields the best agreement with the data with the minimum average difference. Moreover, drift flux analysis is performed to predict void-weighted area-averaged bubble velocity and area-averaged void fraction. Based on the current database, functional

Numerical Investigation on the Heat Extraction Capacity of Dual Horizontal Wells in Enhanced Geothermal Systems Based on the 3-D THM Model

Directory of Open Access Journals (Sweden)

Zhixue Sun

2018-01-01

Full Text Available The Enhanced Geothermal System (EGS constructs an artificial thermal reservoir by hydraulic fracturing to extract heat economically from hot dry rock. As the core element of the EGS heat recovery process, mass and heat transfer of working fluid mainly occurs in fractures. Since the direction of the natural and induced fractures are generally perpendicular to the minimum principal stress in the formation, as an effective stimulation approach, horizontal well production could increase the contact area with the thermal reservoir significantly. In this paper, the thermal reservoir is developed by a dual horizontal well system and treated as a fractured porous medium composed of matrix rock and discrete fracture network. Using the local thermal non-equilibrium theory, a coupled THM mathematical model and an ideal 3D numerical model are established for the EGS heat extraction process. EGS heat extraction capacity is evaluated in the light of thermal recovery lifespan, average outlet temperature, heat production, electricity generation, energy efficiency and thermal recovery rate. The results show that with certain reservoir and production parameters, the heat production, electricity generation and thermal recovery lifespan can achieve the commercial goal of the dual horizontal well system, but the energy efficiency and overall thermal recovery rate are still at low levels. At last, this paper puts forward a series of optimizations to improve the heat extraction capacity, including production conditions and thermal reservoir construction design.

Experimental Study on Natural Convection Heat Transfer From two Parallel Horizontal Cylinders in Horizontal Cylindrical Enclosure

Directory of Open Access Journals (Sweden)

Ahmed T. Ahmed

2013-05-01

Full Text Available  An experimental study on natural convection heat transfer from two parallel horizontal cylinders in horizontal cylindrical enclosure was carried out under condition of constant surfaces temperature for two cylinders and cylindrical enclosure. The study included the effect of Rayleigh number, rotation angle that represent the confined angle between the passing horizontal plane in cylindrical enclosure center and passing line in two cylinders centers, and the spaces between two cylinders on their heat loss ability.39An experimental set-up was used for this purpose which consist watercontainer, test section which is formed of plastic cylinder that represent the cylindrical enclosure, and two heating elements which are formed of two copper cylinders with (19 mm in diameters heated internally by electrical sources that represents transfer and heat loss elements through this set-up.      The experiments were done at the range of Rayleigh number between ( , cylinders rotation angle at ( , and spacing ratio at ( .     The study showed that the ability of heat loss from two cylinders is a function of Rayleigh number, cylinders rotation angle, and the spaces between them. This ability is increased by increasing of Rayleigh number and it was showed that this ability reaches maximum value at the first cylinder ( and minimum value at the second cylinder ( at spacing ratio (S/D=3 and rotation angle ( for the first and ( for the second cylinder respectively.      The effective variables on natural convection heat transfer from the above two cylinders are related by two correlating equations, each one explains dimensionless relation of heat transfer from each cylinder that represented by Nusselt number against Rayleigh number, rotation angle, and the spacing ratio between two cylinders. 

Influence of initial stress, irregularity and heterogeneity on Love-type wave propagation in double pre-stressed irregular layers lying over a pre-stressed half-space

Science.gov (United States)

Singh, Abhishek Kumar; Das, Amrita; Parween, Zeenat; Chattopadhyay, Amares

2015-10-01

The present paper deals with the propagation of Love-type wave in an initially stressed irregular vertically heterogeneous layer lying over an initially stressed isotropic layer and an initially stressed isotropic half-space. Two different types of irregularities, viz., rectangular and parabolic, are considered at the interface of uppermost initially stressed heterogeneous layer and intermediate initially stressed isotropic layer. Dispersion equations are obtained in closed form for both cases of irregularities, distinctly. The effect of size and shape of irregularity, horizontal compressive initial stress, horizontal tensile initial stress, heterogeneity of the uppermost layer and width ratio of the layers on phase velocity of Love-type wave are the major highlights of the study. Comparative study has been made to identify the effects of different shapes of irregularity, presence of heterogeneity and initial stresses. Numerical computations have been carried out and depicted by means of graphs for the present study.

Analytical, numerical and experimental investigations of transverse fracture propagation from horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Rahman, M.M.; Hossain, M.M.; Crosby, D.G.; Rahman, M.K.; Rahman, S.S. [School of Petroleum Engineering, The University of New South Wales, 2052 Sydney (Australia)

2002-08-01

This paper presents results of a comprehensive study involving analytical, numerical and experimental investigations into transverse fracture propagation from horizontal wells. The propagation of transverse hydraulic fractures from horizontal wells is simulated and investigated in the laboratory using carefully designed experimental setups. Closed-form analytical theories for Mode I (opening) stress intensity factors for idealized fracture geometries are reviewed, and a boundary element-based model is used herein to investigate non-planar propagation of fractures. Using the mixed mode fracture propagation criterion of the model, a reasonable agreement is found with respect to fracture geometry, net fracture pressures and fracture propagation paths between the modeled fractures and the laboratory tested fractures. These results suggest that the propagation of multiple fractures requires higher net pressures than a single fracture, the underlying reason of which is theoretically justified on the basis of local stress distribution.

A Comprehensive Comparison Study of Empirical Cutting Transport Models in Inclined and Horizontal Wells

Directory of Open Access Journals (Sweden)

Asep Mohamad Ishaq Shiddiq

2017-07-01

Full Text Available In deviated and horizontal drilling, hole-cleaning issues are a common and complex problem. This study explored the effect of various parameters in drilling operations and how they affect the flow rate required for effective cutting transport. Three models, developed following an empirical approach, were employed: Rudi-Shindu’s model, Hopkins’, and Tobenna’s model. Rudi-Shindu’s model needs iteration in the calculation. Firstly, the three models were compared using a sensitivity analysis of drilling parameters affecting cutting transport. The result shows that the models have similar trends but different values for minimum flow velocity. Analysis was conducted to examine the feasibility of using Rudi-Shindu’s, Hopkins’, and Tobenna’s models. The result showed that Hopkins’ model is limited by cutting size and revolution per minute (RPM. The minimum flow rate from Tobenna’s model is affected only by well inclination, drilling fluid weight and drilling fluid rheological property. Meanwhile, Rudi-Shindu’s model is limited by inclinations above 45°. The study showed that the investigated models are not suitable for horizontal wells because they do not include the effect of lateral section.

Generalized stress field in granular soils heap with Rayleigh–Ritz method

Directory of Open Access Journals (Sweden)

Gang Bi

2017-02-01

Full Text Available The stress field in granular soils heap (including piled coal will have a non-negligible impact on the settlement of the underlying soils. It is usually obtained by measurements and numerical simulations. Because the former method is not reliable as pressure cells instrumented on the interface between piled coal and the underlying soft soil do not work well, results from numerical methods alone are necessary to be doubly checked with one more method before they are extended to more complex cases. The generalized stress field in granular soils heap is analyzed with Rayleigh–Ritz method. The problem is divided into two cases: case A without horizontal constraint on the base and case B with horizontal constraint on the base. In both cases, the displacement functions u(x, y and v(x, y are assumed to be cubic polynomials with 12 undetermined parameters, which will satisfy the Cauchy's partial differential equations, generalized Hooke's law and boundary equations. A function is built with the Rayleigh–Ritz method according to the principle of minimum potential energy, and the problem is converted into solving two undetermined parameters through the variation of the function, while the other parameters are expressed in terms of these two parameters. By comparison of results from the Rayleigh–Ritz method and numerical simulations, it is demonstrated that the Rayleigh–Ritz method is feasible to study the generalized stress field in granular soils heap. Solutions from numerical methods are verified before being extended to more complicated cases.

Analysis of the D0 Crane Rail as a Support for a Horizontal Lifeline

International Nuclear Information System (INIS)

Cease, H.

2000-01-01

The D-Zero crane rail is analyzed for use as an anchor support for a one person Horizon(trademark) Horizontal Lifeline system that will span the pit area at D-Zero assembly hall. The lifeline will span 75 ft across the pit area, will be located out of the travel of the crane and above the concrete lentil wall. The crane rail is a suitable anchor for a one person Horizon TM Horizontal Lifeline system. The expected stress on the rail is 1,995 psi which has a factor of safety of 5.5 on the allowable stress. The anchor position is located 18 feet away from the concrete lentil wall and out of the travel of the overhead crane.

Intra-Wellbore Head Losses in a Horizontal Well with both Kinematic and Frictional Effects in an Anisotropic Confined Aquifer between Two Streams

Science.gov (United States)

Wang, Q.; Zhan, H.

2017-12-01

Horizontal drilling becomes an appealing technology for water exploration or aquifer remediation in recent decades, due to the decreasing operational cost and many technical advantages over the vertical wells. However, many previous studies on the flow into horizontal wells were based on the uniform flux boundary condition (UFBC) for treating horizontal wells, which could not reflect the physical processes of flow inside the well accurately. In this study, we investigated transient flow into a horizontal well in an anisotropic confined aquifer between two streams for three types of boundary conditions of treating the horizontal well, including UFBC, uniform head boundary condition (UHBC), and mixed-type boundary condition (MTBC). The MTBC model considered both kinematic and frictional effects inside the horizontal well, in which the kinematic effect referred to the accelerational and fluid inflow effects. The new solution of UFBC was derived by superimposing the point sink/source solutions along the axis of the horizontal well with a uniform strength. The solutions of UHBC and MTBC were obtained by a hybrid analytical-numerical method, and an iterative method was proposed to determine the minimum well segment number required to yield sufficiently accurate answer. The results showed that the differences among the UFBC, UHBC, MTBCFriction and MTBC solutions were obvious, in which MTBCFriction represented the solutions considering the frictional effect but ignoring the kinematic effect. The MTBCFriction and MTBC solutions were sensitive to the flow rate, and the difference of these two solutions increases with the flow rate, suggesting that the kinematic effect could not be ignored for studying flow to a horizontal well, especially when the flow rate is great. The well specific inflow (WSI) (which is the inflow per unit screen length at a specified location of the horizontal well) increased with the distance along the wellbore for the MTBC model at early stage, while

Active vibration suppression of helicopter horizontal stabilizers

Science.gov (United States)

Cinquemani, Simone; Cazzulani, Gabriele; Resta, Ferruccio

2017-04-01

Helicopters are among the most complex machines ever made. While ensuring high performance from the aeronautical point of view, they are not very comfortable due to vibration mainly created by the main rotor and by the interaction with the surrounding air. One of the most solicited structural elements of the vehicle are the horizontal stabilizers. These elements are particularly stressed because of their composite structure which, while guaranteeing lightness and strength, is characterized by a low damping. This work makes a preliminary analysis on the dynamics of the structure and proposes different solutions to actively suppress vibrations. Among them, the best in terms of the relationship between performance and weight / complexity of the system is that based on inertial actuators mounted on the inside of the horizontal stabilizers. The work addresses the issue of the design of the device and its use in the stabilizer from both the numerical and the experimental points of view.

Evaluation of the state of stress at the Forsmark site. Preliminary site investigation Forsmark area - version 1.2

Energy Technology Data Exchange (ETDEWEB)

Sjoeberg, Jonny; Lindfors, Ulf; Perman, Fredrik; Ask, Daniel [SwedPower AB, Stockholm (Sweden)

2005-09-15

horizontal stress was found in gneissic rock. Aside from this, clear correlations between rock type and measured stresses were also lacking, as well as confirmatory evidence of a low-stress environment in the superficial, more fractured bedrock. Assessment of a representative stress state for the Forsmark site was based on different subsets of the total data set of stress measurements. Linear stress profiles were assumed for the horizontal and vertical stress components, with each stress profile being representative of the conditions within the tectonic lens. These stress profiles define the lower and upper limit of the stress state based on the data considered reliable for each stress component. The resulting stress profiles are: Maximum horizontal stress ({sigma}H) applicable for 230-450 m vertical depth (z): Lower limit: {sigma}H = 0.085z (MPa), Upper limit: {sigma}H = 13+0.095z (MPa), Alternative upper limit: {sigma}H 29+0.050z (MPa). Orientation: 140 deg (clockwise from North). Minimum horizontal stress ({sigma}h) applicable for 0-1,000 m vertical depth (z): Lower limit: {sigma}h = 0.022z (MPa), Upper limit: {sigma}h 5.5+0.0265z (MPa). Vertical stress ({sigma}v) applicable for 0-800 m vertical depth (z): {sigma}v = 0.0265z (MPa). Future measurements and activities should be planned to address the gaps indicated by the present data set. It is recommended that new overcoring measurements are conducted, starting already at approximately 100 m depth below the ground surface, and continued as deep as possible - until the method is no longer applicable (extensive core damage and/or core discing inhibiting correct installation and/or overcoring of the measurement probe). Furthermore, any observations on core discing should be logged in detail to provide confirmatory evidence of stress magnitudes. If core discing of solid core is observed, pilot hole drilling with subsequent overcoring (without installation of the measurement probe) should be considered to induce ring discing

Evaluation of the state of stress at the Forsmark site. Preliminary site investigation Forsmark area - version 1.2

International Nuclear Information System (INIS)

Sjoeberg, Jonny; Lindfors, Ulf; Perman, Fredrik; Ask, Daniel

2005-09-01

gneissic rock. Aside from this, clear correlations between rock type and measured stresses were also lacking, as well as confirmatory evidence of a low-stress environment in the superficial, more fractured bedrock. Assessment of a representative stress state for the Forsmark site was based on different subsets of the total data set of stress measurements. Linear stress profiles were assumed for the horizontal and vertical stress components, with each stress profile being representative of the conditions within the tectonic lens. These stress profiles define the lower and upper limit of the stress state based on the data considered reliable for each stress component. The resulting stress profiles are: Maximum horizontal stress (σH) applicable for 230-450 m vertical depth (z): Lower limit: σH = 0.085z (MPa), Upper limit: σH = 13+0.095z (MPa), Alternative upper limit: σH 29+0.050z (MPa). Orientation: 140 deg (clockwise from North). Minimum horizontal stress (σh) applicable for 0-1,000 m vertical depth (z): Lower limit: σh = 0.022z (MPa), Upper limit: σh 5.5+0.0265z (MPa). Vertical stress (σv) applicable for 0-800 m vertical depth (z): σv = 0.0265z (MPa). Future measurements and activities should be planned to address the gaps indicated by the present data set. It is recommended that new overcoring measurements are conducted, starting already at approximately 100 m depth below the ground surface, and continued as deep as possible - until the method is no longer applicable (extensive core damage and/or core discing inhibiting correct installation and/or overcoring of the measurement probe). Furthermore, any observations on core discing should be logged in detail to provide confirmatory evidence of stress magnitudes. If core discing of solid core is observed, pilot hole drilling with subsequent overcoring (without installation of the measurement probe) should be considered to induce ring discing of a hollow core. Having two observations of different core geometries can

Minimum critical crack depths in pressure vessels guidelines for nondestructive testing

International Nuclear Information System (INIS)

Crossley, M.R.; Townley, C.H.A.

1983-09-01

Estimates of the minimum critical depths which can be expected in high quality vessels designed to certain British and American Code rules are given. A simple means of allowing for fatigue crack growth in service is included. The data which are presented can be used to decide what sensitivity and what reporting levels should be employed during an ultrasonic inspection of a pressure vessel. It is emphasised that the minimum crack depths are those which would be relevant to a vessel in which the material is stressed to its maximum permitted value during operation. Stresses may, in practice, be significantly less than this. Less restrictive inspection standards may be established, if it were considered worthwhile to carry out a detailed stress analysis of the particular vessel under examination. (author)

The blind faith deep water horizontal pipeline tie-in project

Energy Technology Data Exchange (ETDEWEB)

Charalambides, John Nicos [Oceaneering International, Inc., Houston, TX (United States)

2009-12-19

This presentation will concentrate on the design challenges, experience and learning from the SIT and offshore installation of two deepwater pipeline tie-ins using first-of-its-kind subsea technology and installation methodologies on the 'Blind Faith' project. The Blind Faith Subsea Tie-Ins join the Blind Faith oil and gas pipelines with the Canyon Chief gas pipeline and the Mountaineer oil pipeline in 5100 feet of water. Both of the Blind Faith oil and gas pipelines are terminated with conventional PLEMs providing a horizontal connector for the tie-in and a vertical connector for a future tie-in connection point. The connectors are ROV operable/installable clamp style connectors. The method of joining to the Canyon Chief oil and gas pipelines and the type of jumper employed are unique to the tie-in. An ROV operable / installable mechanical pipe end connector connects the bare ends of the Canyon Chief and Mountaineer pipelines. The mechanical pipe end connector is fitted with an integral clamp connector hub and rests on an ROV installed mud mat. After installation of the mechanical connector, metrology was performed to create a neutral state horizontal jumper for joining the mechanical connector hub and the Blind Faith PLEM. The neutral state horizontal jumper is a compliant 'Z-Bend' design. During installation the jumper was elastically pre-deformed using a bowstring system. Pre-deformation of the jumper provided installation clearances and facilitated the neutral stress state after installation. Once landed the jumper bowstring was relaxed, allowing the jumper to expand to fit between the hubs. After expansion and make-up, the clamp connectors were tightened via an ROV operated hydraulic torque wrench. A seal test verified the integrity of the connections. After installation the jumper remains in a minimal residual stress state atypical of most horizontal jumpers. The horizontal jumper was chosen over the vertical jumper because it provides a

The state of stress in British rocks

International Nuclear Information System (INIS)

Klein, R.J.; Brown, E.T.

1983-03-01

When designing underground works, it is necessary to take account of not only the vertical stresses arising predictably from the weight of the rock overhead, but also horizontal stresses which may vary from one direction to another as a result of past tectonic action. This report discussed the techniques that have been used to measure such stresses. Few determinations have been made in Great Britain, so it has been necessary to augment what little is known by reference to fault systems, relying on correlations between the measured magnitude and direction of maximum horizontal stress with local tectonic history. This has enabled general conclusions to be reached for Great Britain. (author)

Full-scale fire experiments on vertical horizontal cable trays

International Nuclear Information System (INIS)

Mangs, J.; Keski-Rahkonen, O.

1997-10-01

Two full-scale fire experiments on PVC cables used in nuclear power plants were carried out, one with cables in vertical position and one with cables in horizontal position. The vertical cable bundle, 3 m high, 300 mm wide and 30 mm thick, was attached to a steel cable ladder. The vertical bundle experiment was carried out in nearly free space with three walls near the cable ladder guiding air flow in order to stabilise flames. The horizontal cable experiment was carried out in a small room with five cable bundles attached to steel cable ladders. Three of the 2 m long cable bundles were located in an array, equally spaced above each other near one long side of the room and two correspondingly near the opposite long side. The vertical cable bundle was ignited with a small propane gas burner beneath the lower edge of the bundle. The horizontal cable bundles were ignited with a small propane burner beneath the lowest bundle in an array of three bundles. Rate of heat release by means of oxygen consumption calorimetry, mass change, CO 2 , CO and smoke production rate and gas, wall and cable surface temperatures were measured as a function of time, as well as time to sprinkler operation and failure of test voltage in cables. Additionally, the minimum rate of heat release needed to ignite the bundle was determined. This paper concentrates on describing and recording the experimental set-up and the data obtained. (orig.)

Reliability Based Geometric Design of Horizontal Circular Curves

Science.gov (United States)

Rajbongshi, Pabitra; Kalita, Kuldeep

2018-06-01

Geometric design of horizontal circular curve primarily involves with radius of the curve and stopping sight distance at the curve section. Minimum radius is decided based on lateral thrust exerted on the vehicles and the minimum stopping sight distance is provided to maintain the safety in longitudinal direction of vehicles. Available sight distance at site can be regulated by changing the radius and middle ordinate at the curve section. Both radius and sight distance depend on design speed. Speed of vehicles at any road section is a variable parameter and therefore, normally the 98th percentile speed is taken as the design speed. This work presents a probabilistic approach for evaluating stopping sight distance, considering the variability of all input parameters of sight distance. It is observed that the 98th percentile sight distance value is much lower than the sight distance corresponding to 98th percentile speed. The distribution of sight distance parameter is also studied and found to follow a lognormal distribution. Finally, the reliability based design charts are presented for both plain and hill regions, and considering the effect of lateral thrust.

Reliability Based Geometric Design of Horizontal Circular Curves

Science.gov (United States)

Rajbongshi, Pabitra; Kalita, Kuldeep

2018-03-01

Geometric design of horizontal circular curve primarily involves with radius of the curve and stopping sight distance at the curve section. Minimum radius is decided based on lateral thrust exerted on the vehicles and the minimum stopping sight distance is provided to maintain the safety in longitudinal direction of vehicles. Available sight distance at site can be regulated by changing the radius and middle ordinate at the curve section. Both radius and sight distance depend on design speed. Speed of vehicles at any road section is a variable parameter and therefore, normally the 98th percentile speed is taken as the design speed. This work presents a probabilistic approach for evaluating stopping sight distance, considering the variability of all input parameters of sight distance. It is observed that the 98th percentile sight distance value is much lower than the sight distance corresponding to 98th percentile speed. The distribution of sight distance parameter is also studied and found to follow a lognormal distribution. Finally, the reliability based design charts are presented for both plain and hill regions, and considering the effect of lateral thrust.

Numerical estimates of the maximum sustainable pore pressure in anticline formations using the tensor based concept of pore pressure-stress coupling

Directory of Open Access Journals (Sweden)

Andreas Eckert

2015-02-01

Full Text Available The advanced tensor based concept of pore pressure-stress coupling is used to provide pre-injection analytical estimates of the maximum sustainable pore pressure change, ΔPc, for fluid injection scenarios into generic anticline geometries. The heterogeneous stress distribution for different prevailing stress regimes in combination with the Young's modulus (E contrast between the injection layer and the cap rock and the interbedding friction coefficient, μ, may result in large spatial and directional differences of ΔPc. A single value characterizing the cap rock as for horizontal layered injection scenarios is not obtained. It is observed that a higher Young's modulus in the cap rock and/or a weak mechanical coupling between layers amplifies the maximum and minimum ΔPc values in the valley and limb, respectively. These differences in ΔPc imposed by E and μ are further amplified by different stress regimes. The more compressional the stress regime is, the larger the differences between the maximum and minimum ΔPc values become. The results of this study show that, in general compressional stress regimes yield the largest magnitudes of ΔPc and extensional stress regimes provide the lowest values of ΔPc for anticline formations. Yet this conclusion has to be considered with care when folded anticline layers are characterized by flexural slip and the friction coefficient between layers is low, i.e. μ = 0.1. For such cases of weak mechanical coupling, ΔPc magnitudes may range from 0 MPa to 27 MPa, indicating imminent risk of fault reactivation in the cap rock.

Interpretation of the Haestholmen in situ state of stress based on core damage observations

International Nuclear Information System (INIS)

Hakala, M.

2000-01-01

At the Haestholmen investigation site, direct in situ stress measurements, overcoring and hydraulic fracturing have been unsuccessful because of ring disking and horizontal hydraulic fracturing. Prior to this study, a detailed study on both core disking and ring disking was made, and based on those results an in situ state of stress interpretation method was developed. In this work this method is applied to the Haestholmen site. The interpretation is based on disk fracture type, spacing and shape. Also, the Hoek-Brown strength envelope and Poisson's ratio of intact rock are needed. The interpretation result is most reliable if both core disking and ring disking information at the same depth levels is available. A detailed core logging showed that ring disking is systematic below the -365 m level in the vertical overcoring stress measurement hole, HH-KR6. On the other hand, no representative core disking exists except for two points in two differently oriented subvertical boreholes HH-KR2 and HHKR7. Because the interpretation has to be based on ring disking only, upper and lower estimates for the vertical stress were set. These were gravitational and 67% of gravitational. Furthermore, the in situ stress state was assumed to be in horizontal and vertical planes, because the disking in vertical borehole HH-KR6 was not inclined. The interpretation resulted in a good estimate for the major horizontal stress but none of the horizontal stress rations ( 0.25, 0.5, 0.75 and 1.0 ) or vertical stress assumptions studied are clearly more probable the others. At the 500 m level the resulting maximum horizontal stress is 41 MPa. If a linear fit through the zero depth and zero stress point is applied, the maximum horizontal stress gradient is 0.0818 z MPa/m with a standard deviation between 5 and 12 per cent. The orientation of the major horizontal stress is 108 with standard deviation of 21 degrees. The interpreted major horizontal stress state also indicated that systematic

Rock stress investigations

International Nuclear Information System (INIS)

Pahl, A.; Heusermann, St.; Braeuer, V.; Gloeggler, W.

1989-04-01

On the research project 'Rock Stress Mesurements' the BGR has developed and tested several methods for use in boreholes at a depth of 200 m. Indirect stress measurements using overcoring methods with BGR-probes and CSIR-triaxial cells as well as direct stress measurements using the hydraulic-fracturing method were made. To determine in-situ rock deformation behavior borehole deformation tests, using a BGR-dilatometer, were performed. Two types of the BGR-probe were applied: a four-component-probe to determine horizontal stresses and a five-component-probe to determine a quasi three-dimensional stress field. The first time a computer for data processing was installed in the borehole together with the BGR-probe. Laboratory tests on low cylinders were made to study the stress-deformation behavior. To validate and to interprete the measurement results some test methods were modelled using the finite-element method. The dilatometer-tests yielded high values of Young's modulus, whereas laboratory tests showed lower values with a distinct deformation anisotropy. Stress measurements with the BGR-probe yielded horizontal stresses being higher than the theoretical overburden pressure. These results are comparable to the results of the hydraulic fracturing tests, whereas stresses obtained with CSIR-triaxial cells are lower. The detailed geological mapping of the borehole indicated relationships between stress and geology. With regard to borehole depth different zones of rock structure joint frequency, joint orientation, and orientation of microfissures as well as stress magnitude, stress direction, and degree of deformation anisotropy could be distinguished. (author) 4 tabs., 76 figs., 31 refs

Heavy crude production from shallow formations: long horizontal wells versus horizontal fractures

Energy Technology Data Exchange (ETDEWEB)

Valko, P.; Economides, M. J. [Texas A and M Univ., TX (United States)

1998-12-31

The feasibility of producing heavy oil from shallow formations using either horizontal wells or short horizontal wells fractured horizontally is demonstrated. The problem of optimum proppant placement is solved in two steps. In step one, the finite productivity performance is considered in general terms showing that the performance is a function of two dimensionless parameters. Following derivation of optimum conditions, the solution is applied to the horizontal fracture consideration. The limiting factor is that to create an effective finite conductivity fracture, the dimensionless fracture conductivity must be on the order of unity, a fracture that is difficult to realize in higher permeability formations. The best candidates for the suggested configuration are shallow or moderate formations, or formations otherwise proven to accept horizontal fractures, and formations with low permeability/viscosity ratio. 7 refs., 2 tabs., 10 figs., 2 appendices.

A Novel Analytical Solution for Estimating Aquifer Properties and Predicting Stream Depletion Rates by Pumping from a Horizontally Anisotropic Aquifer

Science.gov (United States)

Huang, Y.; Zhan, H.; Knappett, P.

2017-12-01

Past studies modeling stream-aquifer interactions commonly account for vertical anisotropy, but rarely address horizontal anisotropy, which does exist in certain geological settings. Horizontal anisotropy is impacted by sediment deposition rates, orientation of sediment particles and orientations of fractures etc. We hypothesize that horizontal anisotropy controls the volume of recharge a pumped aquifer captures from the river. To test this hypothesis, a new mathematical model was developed to describe the distribution of drawdown from stream-bank pumping with a well screened across a horizontally anisotropic, confined aquifer, laterally bounded by a river. This new model was used to determine four aquifer parameters including the magnitude and directions of major and minor principal transmissivities and storativity based on the observed drawdown-time curves within a minimum of three non-collinear observation wells. By comparing the aquifer parameters values estimated from drawdown data generated known values, the discrepancies of the major and minor transmissivities, horizontal anisotropy ratio, storativity and the direction of major transmissivity were 13.1, 8.8, 4, 0 and managers to exploit groundwater resource reasonably while protecting stream ecosystem.

Stress ratio determination from the core-disking phenomenon

International Nuclear Information System (INIS)

Lehnhoff, T.F.; Stefansson, B.; Thirumalai, K.

1982-08-01

The ability to predict in situ stress conditions from standard core samples offers planning and site-selection advantages for most underground facilities. This paper presents an empirical relation for estimating the horizontal to vertical stress ratio in basalt. The resulting estimates can then be used to help assess the extent to which measurement of in situ stress is required. The core disking phenomenon has long been used as an indicator of high in situ stress. It is concluded that disks form as the result of tensile failure initiation rather than shear failure initiation of the core. It is deduced that the tensile failure begins at the edge of the core and propagates toward the center in shear rather than beginning at the center and propagating outward. An empirical relation for horizontal to vertical stress ratio variation with depth has been developed and is shown to agree substantially with previous measured horizontal to vertical stress ratios for locations in several areas of the world. The stress-ratio predictions are justified based on finite-element studies using linear elastic analysis and also nonlinear (tension cut-off) analysis. Indications of fracture propagation paths were determined from the analyses. The shape of the predicted propagation path agrees well with physical observations

Stress regimes in the northwest of Iran from stress inversion of earthquake focal mechanisms

Science.gov (United States)

Afra, Mahsa; Moradi, Ali; Pakzad, Mehrdad

2017-11-01

Northwestern Iran is one of the seismically active regions with a high seismic risk in the world. This area is a part of the complex tectonic system due to the interaction between Arabia, Anatolia and Eurasia. The purpose of this study is to deduce the stress regimes in the northwestern Iran and surrounding regions from stress inversion of earthquake focal mechanisms. We compile 92 focal mechanisms data from the Global CMT catalogue and other sources and also determine the focal mechanisms of 14 earthquakes applying the moment tensor inversion. We divide the studied region into 9 zones using similarity of the horizontal GPS velocities and existing focal mechanisms. We implement two stress inversion methods, Multiple Inverse Method and Iterative Joint Inversion Method, which provide comparable results in terms of orientations of maximum horizontal stress axes SHmax. The similar results of the two methods should make us more confident about the interpretations. We consider zones of exclusion surrounding all the earthquakes according to independent focal mechanisms hypothesis. The hypothesis says that the inversion should involve events that are far enough from each other in order that any previous event doesn't affect the stress field near the earthquake under consideration. Accordingly we deal with the matter by considering zones of exclusion around all the events. The result of exclusion is only significant for eastern Anatolia. The stress regime in this region changes from oblique to strike slip faulting because of the exclusion. In eastern Anatolia, the direction of maximum horizontal stress is nearly north-south. The direction alters to east-west in Talesh region. Errors of σ1 are lower in all zones comparing with errors of σ2 and σ3 and there is a trade-off between data resolution and covariance of the model. The results substantiate the strike-slip and thrust faulting stress regimes in the northwest of Iran.

The stress field and transient stress generation at shallow depths in the Canadian shield

International Nuclear Information System (INIS)

Hasegawa, H.S.

1984-01-01

A prominent feature of the stress field in eastern Canada is the high horizontal stress at shallow depths. Possible causative factors to this shallow stress field are remanent stresses from a previous tectonic orogeny, plate tectonic stresses and glacial-related stresses (glacial drag and flexual stress). The inherent difficulty in differentiating residual from current stress is one of the reasons why the relative contributions to the stress field from the phenomena described above are not properly understood. Maximum stress-strain changes an underground vault is likely to encounter from natural phenomena should occur when the periphery of the advancing or retreating glacier is near the vault. Theoretical calculations indicate that lithospheric flexure, differential postglacial uplift and possibly glacial drag may be able to generate significant horizontal stresses around a vault. In order to calculate the earthquake potential of these induced stress changes, the ambient tectonic stress field should also be included and a suitable failure criterion (e.g. Coulomb-Mohr) used. For earthquakes to generate appreciable stress-strain concentrations near a vault; the seismic signal must contain appreciable energy at appropriate frequencies (wavelengths comparable to vault dimensions) and be of appreciable duration; the particle velocity must be high (> 10 cm/s), induced strain is a function of particle velocity; and, the hypocentre must be less than half a fault length from the vault for residual deformation (strain and tilt) to be significant. The most severe case is when the causative fault intersects the vault

On the relationship between stress intensity factor (K) and minimum ...

African Journals Online (AJOL)

Studies on crack-tip plastic zones are of fundamental importance in describing the process of failure and in formulating various fracture criteria. Minimum plastic zone radius (MPZR) theory is widely used in prediction of crack initiation angle in mixed mode fracture analysis of engineering materials. In this study, shape and ...

Horizontal wells in subsurface remediation

International Nuclear Information System (INIS)

Losonsky, G.; Beljin, M.S.

1992-01-01

This paper reports on horizontal wells which offer an effective alternative to vertical wells in various environmental remediation technologies. Hydrogeological advantages of horizontal wells over vertical wells include a larger zone of influence, greater screen length, higher specific capacity and lower groundwater screen entrance velocity. Because of these advantages, horizontal wells can reduce treatment time and costs of groundwater recovery (pump-and-treat), in situ groundwater aeration (sparging) and soil gas extraction (vacuum extraction). Horizontal wells are also more effective than vertical wells in landfill leachate collection (under-drains), bioremediation, and horizontal grout injection

Stress field models from Maxwell stress functions: southern California

Science.gov (United States)

Bird, Peter

2017-08-01

The lithospheric stress field is formally divided into three components: a standard pressure which is a function of elevation (only), a topographic stress anomaly (3-D tensor field) and a tectonic stress anomaly (3-D tensor field). The boundary between topographic and tectonic stress anomalies is somewhat arbitrary, and here is based on the modeling tools available. The topographic stress anomaly is computed by numerical convolution of density anomalies with three tensor Green's functions provided by Boussinesq, Cerruti and Mindlin. By assuming either a seismically estimated or isostatic Moho depth, and by using Poisson ratio of either 0.25 or 0.5, I obtain four alternative topographic stress models. The tectonic stress field, which satisfies the homogeneous quasi-static momentum equation, is obtained from particular second derivatives of Maxwell vector potential fields which are weighted sums of basis functions representing constant tectonic stress components, linearly varying tectonic stress components and tectonic stress components that vary harmonically in one, two and three dimensions. Boundary conditions include zero traction due to tectonic stress anomaly at sea level, and zero traction due to the total stress anomaly on model boundaries at depths within the asthenosphere. The total stress anomaly is fit by least squares to both World Stress Map data and to a previous faulted-lithosphere, realistic-rheology dynamic model of the region computed with finite-element program Shells. No conflict is seen between the two target data sets, and the best-fitting model (using an isostatic Moho and Poisson ratio 0.5) gives minimum directional misfits relative to both targets. Constraints of computer memory, execution time and ill-conditioning of the linear system (which requires damping) limit harmonically varying tectonic stress to no more than six cycles along each axis of the model. The primary limitation on close fitting is that the Shells model predicts very sharp

Dynamic Response in Transient Stress-Field Behavior Induced by Hydraulic Fracturing

Science.gov (United States)

Jenkins, Andrew

Hydraulic fracturing is a technique which is used to exploit geologic features and subsurface properties in an effort to increase production in low-permeability formations. The process of hydraulic fracturing provides a greater surface contact area between the producing formation and the wellbore and thus increases the amount of recoverable hydrocarbons from within the reservoir. The use of this stimulation technique has brought on massive applause from the industry due to its widespread success and effectiveness, however the dynamic processes that take part in the development of hydraulic fractures is a relatively new area of research with respect to the massive scale operations that are seen today. The process of hydraulic fracturing relies upon understanding and exploiting the in-situ stress distribution throughout the area of study. These in-situ stress conditions are responsible for directing fracture orientation and propagation paths throughout the period of injection. The relative magnitude of these principle stresses is key in developing a successful stimulation plan. In horizontal well plan development the interpretation of stress within the reservoir is required for determining the azimuth of the horizontal well path. These horizontal laterals are typically oriented in a manner such that the well path lies parallel to the minimum horizontal stress. This allows for vertical fractures to develop transversely to the wellbore, or normal to the least principle stress without the theoretical possibility of fractures overlapping, creating the most efficient use of the fluid energy during injection. The orientation and magnitude of these in-situ stress fields however can be dynamic, controlled by the subsequent fracture propagation and redistribution of the surrounding stresses. That is, that as the fracture propagates throughout the reservoir, the relative stress fields surrounding the fractures may see a shift and deviate from their original direction or

Dispersive stresses in wind farms

Science.gov (United States)

Segalini, Antonio; Braunbehrens, Robert; Hyvarinen, Ann

2017-11-01

One of the most famous models of wind farms is provided by the assumption that the farm can be approximated as a horizontally-homogeneous forest canopy with vertically-varying force intensity. By means of this approximation, the flow-motion equations become drastically simpler, as many of the three-dimensional effects are gone. However, the application of the horizontal average operator to the RANS equations leads to the appearance of new transport terms (called dispersive stresses) originating from the horizontal (small-scale) variation of the mean velocity field. Since these terms are related to the individual turbine signature, they are expected to vanish outside the roughness sublayer, providing a definition for the latter. In the present work, an assessment of the dispersive stresses is performed by means of a wake-model approach and through the linearised code ORFEUS developed at KTH. Both approaches are very fast and enable the characterization of a large number of wind-farm layouts. The dispersive stress tensor and its effect on the turbulence closure models are investigated, providing guidelines for those simulations where it is impossible to resolve the farm at a turbine scale due to grid requirements (as, for instance, mesoscale simulations).

Modelling of the Global Geopotential Energy & Stress Field

DEFF Research Database (Denmark)

Schiffer, Christian; Nielsen, S.B.

Lateral density and topography variations yield in and important contribution to the lithospheric stress field. The leading quantity is the Geopotential Energy, the integrated lithostatic pressure in a rock column. The horizontal gradient of this quantity is related to horizontal stresses through...... the Equations of equilibrium of stresses. The Geopotential Energy furthermore can be linearly related to the Geoid under assumption of local isostasy. Satellite Geoid measurements contain, however, also non-isostatic deeper mantle responses of long wavelength. Unfortunately, high-pass filtering of the Geoid...... flow in the presence of local isostasy and a steady state geotherm. Subsequently we use a FEM code to solve the Equations of equilibrium of stresses for a three dimensional elastic shell. The modelled results are shown and compared with the global stress field and other publications....

Natural Fractures Characterization and In Situ Stresses Inference in a Carbonate Reservoir—An Integrated Approach

Directory of Open Access Journals (Sweden)

Ali Shafiei

2018-02-01

Full Text Available In this paper, we characterized the natural fracture systems and inferred the state of in situ stress field through an integrated study in a very complex and heterogeneous fractured carbonate reservoir. Relative magnitudes and orientations of the in-situ principal stresses in a naturally fractured carbonate heavy oil field were estimated with a combination of available data (World Stress Map, geological and geotectonic evidence, outcrop studies and techniques (core analysis, borehole image logs and Side View Seismic Location. The estimates made here using various tools and data including routine core analysis and image logs are confirmatory to estimates made by the World Stress Map and geotectonic facts. NE-SW and NW-SE found to be the dominant orientations for maximum and minimum horizontal stresses in the study area. In addition, three dominant orientations were identified for vertical and sub-vertical fractures atop the crestal region of the anticlinal structure. Image logs found useful in recognition and delineation of natural fractures. The results implemented in a real field development and proved practical in optimal well placement, drilling and production practices. Such integrated studies can be instrumental in any E&P projects and related projects such as geological CO2 sequestration site characterization.

Vertical-to-Horizontal Rotational Myocutaneous Flap for Repairing Cicatricial Lower Lid Ectropion: A Novel Surgical Technique

Directory of Open Access Journals (Sweden)

Yu-Fan Chang

2017-01-01

Full Text Available Objective. To evaluate the efficacy and complications of a novel surgical technique for cicatricial lower lid ectropion that uses a vertical-to-horizontal (V-to-H rotational myocutaneous flap procedure (Tsai procedure. Methods. We performed the V-to-H rotational myocutaneous flap procedure on 20 eyelids in 20 patients with mild to moderate cicatricial lower lid ectropion. A vertical myocutaneous flap was created from the anterior lamella of the vertical pedicle in the lateral third of the lower eyelid. Following a horizontal relaxing incision from the base of the flap, a vertical myocutaneous flap was created and rotated to horizontal. Two patients with combined cicatricial ectropion and paralytic lagophthalmos simultaneously underwent additional lateral tarsorrhaphy. Results. After a minimum follow-up period of 6 months, all patients showed good anatomical and functional improvement with decreased dependence on topical lubricants and a satisfactory cosmetic appearance. Two patients with combined cicatricial and paralytic ectropion had mild residual asymptomatic lagophthalmos. No patients required further revision surgery and there were no complications or recurrence. Conclusion. The V-to-H rotational myocutaneous flap technique was an effective and simple one-stage procedure for correcting cicatricial lower lid ectropion. It lengthened the anterior lamella and tightened horizontal eyelid laxity without the need for a free skin graft.

Horizontal alternating steam drive process for the Orinoco heavy oil belt in eastern Venezuela

Energy Technology Data Exchange (ETDEWEB)

Edgar A. Fernandez R.; Bashbush, J.L. [Schlumberger, Sugar Land, TX (United States)

2008-10-15

Horizontal alternating steam drive (HASD) processes use single horizontal wells that cyclically switch between injection and production phases. The steam chambers generated by the wells are laterally driven by the pressure differentials created by adjacent producers to form a sweeping front between the wells. This feasibility study assessed the use of HASD processes at a heavy oil reservoir in Venezuela. The study used numerical simulations from a representative reservoir with a 5-horizontal well array to asses the HASD recovery technique under various scenarios. Sensitivity analyses were also conducted to consider the positioning of the horizontal well placement in the reservoir column; different injection sequences; variations in the duration of injection cycles; injection rates; and the lengths of the horizontal reach of the wells. Results of the study suggested that HASD is a suitable alternative for reservoirs with sands in the 20 foot to 50 foot thickness range. HASD achieved average recovery factors of above 20 per cent over a 15 year period, and required fewer wells than steam assisted gravity drainage (SAGD) processes. It was concluded that the wells must be designed to consider the additional thermal stresses resulting the repeated injection and production cycles associated with HASD processes. The 6 refs., 2 tabs., 16 figs.

Vertical and horizontal subsidiarity

Directory of Open Access Journals (Sweden)

Ivan V. Daniluk

2016-02-01

Full Text Available This article makes an attempt to analyze the principle of subsidiarity in its two main manifestations, namely vertical and horizontal, to outline the principles of relations between the state and regions within the vertical subsidiarity, and features a collaboration of the government and civil society within the horizontal subsidiarity. Scientists identify two types, or two levels of the subsidiarity principle: vertical subsidiarity and horizontal subsidiarity. First, vertical subsidiarity (or territorial concerning relations between the state and other levels of subnational government, such as regions and local authorities; second, horizontal subsidiarity (or functional concerns the relationship between state and citizen (and civil society. Vertical subsidiarity expressed in the context of the distribution of administrative responsibilities to the appropriate higher level lower levels relative to the state structure, ie giving more powers to local government. However, state intervention has subsidiary-lower action against local authorities in cases of insolvency last cope on their own, ie higher organisms intervene only if the duties are less authority is insufficient to achieve the goals. Horizontal subsidiarity is within the relationship between power and freedom, and is based on the assumption that the concern for the common good and the needs of common interest community, able to solve community members (as individuals and citizens’ associations and role of government, in accordance horizontal subsidiarity comes to attracting features subsidiarity assistance, programming, coordination and possibly control.

Alternativa estructural de refuerzo horizontal en muros de mampostería Structural alternative of horizontal reinforcement in masonry walls

Directory of Open Access Journals (Sweden)

Diego Fernando Páez Moreno

2009-01-01

Full Text Available La implementación de refuerzo horizontal en muros de mampostería con ladrillo macizo de arcilla cocida es una técnica empleada en varios países. En este trabajo se propone un análisis para muros de mampostería representativos de la ciudad de Tunja con la implementación de grafiles de acero como alternativa de refuerzo horizontal. Este estudio involucra la definición de los tipos de materiales a emplear, las características de los muros a ensayar y las variables que se deben aplicar, tanto en los muros como en la ejecución del ensayo de compresión diagonal, que define tipos de muros con características propias de refuerzo. Los resultados del proceso de análisis del comportamiento individual y general de los muros de mampostería sometidos al ensayo de compresión diagonal permiten identificar la variación del esfuerzo cortante representativo para cada tipo de muro, en relación con el refuerzo empleado en los diferentes modelos y la tipología de falla.Implementation of horizontal reinforcement in masonry walls with solid cooked clay bricks is a commonly used technique in several countries. This article is intended to analyze masonry walls representatives of Tunja City, with implementation of small steel bars as an alternative of horizontal reinforcement. This study involves definition of types of materials to be used, characteristics of walls to be tested, and variables which should be applied in both walls and during the execution of the diagonal compression test which defines the types of walls with own characteristics of reinforcement. Results from individual and general behavior analysis process of masonry walls subject to diagonal compression tests allow identifying variation of shear stress for each kind of wall, in relation to reinforcement used in several models and failure typology.

Phylogenetic Applications of the Minimum Contradiction Approach on Continuous Characters

Directory of Open Access Journals (Sweden)

Marc Thuillard

2009-01-01

Full Text Available We describe the conditions under which a set of continuous variables or characters can be described as an X-tree or a split network. A distance matrix corresponds exactly to a split network or a valued X-tree if, after ordering of the taxa, the variables values can be embedded into a function with at most a local maximum and a local minimum, and crossing any horizontal line at most twice. In real applications, the order of the taxa best satisfying the above conditions can be obtained using the Minimum Contradiction method. This approach is applied to 2 sets of continuous characters. The first set corresponds to craniofacial landmarks in Hominids. The contradiction matrix is used to identify possible tree structures and some alternatives when they exist. We explain how to discover the main structuring characters in a tree. The second set consists of a sample of 100 galaxies. In that second example one shows how to discretize the continuous variables describing physical properties of the galaxies without disrupting the underlying tree structure.

Improved waterflooding efficiency by horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Popa, C. G. [Petroleum and Gas Univ., Ploesti (Romania); Clipea, M. [SNP Petrom SA, ICPT Campina (Romania)

1998-12-31

The influence of well pattern involving the use of horizontal wells on the overall efficiency of the waterflooding process was analyzed. Three different scenarios were examined: (1) a pattern of using two parallel horizontal wells, one for injection, the other for production, (2) a pattern of one horizontal well for water injection and several vertical wells for production, and (3) a pattern of using vertical wells for injection and one horizontal well for production. In each case, the waterflooding process was simulated using a two phase two dimensional numerical model. Results showed that the pressure loss along the horizontal section had a large influence on the sweep efficiency whether the horizontal well was used for injection or production. Overall, the most successful combination appeared to be using vertical wells for injection and horizontal wells for production. 4 refs., 1 tab., 15 figs.

A collapse pressure prediction model for horizontal shale gas wells with multiple weak planes

Directory of Open Access Journals (Sweden)

Ping Chen

2015-01-01

Full Text Available Since collapse of horizontal wellbore through long brittle shale interval is a major problem, the occurrence characteristics of weak planes were analyzed according to outcrop, core, and SEM and FMI data of shale rocks. A strength analysis method was developed for shale rocks with multiple weak planes based on weak-plane strength theory. An analysis was also conducted of the strength characteristics of shale rocks with uniform distribution of multiple weak planes. A collapse pressure prediction model for horizontal wells in shale formation with multiple weak planes was established, which takes into consideration the occurrence of each weak plane, wellbore stress condition, borehole azimuth, and in-situ stress azimuth. Finally, a case study of a horizontal shale gas well in southern Sichuan Basin was conducted. The results show that the intersection angle between the shale bedding plane and the structural fracture is generally large (nearly orthogonal; with the increase of weak plane number, the strength of rock mass declines sharply and is more heavily influenced by weak planes; when there are more than four weak planes, the rock strength tends to be isotropic and the whole strength of rock mass is greatly weakened, significantly increasing the risk of wellbore collapse. With the increase of weak plane number, the drilling fluid density (collapse pressure to keep borehole stability goes up gradually. For instance, the collapse pressure is 1.04 g/cm3 when there are no weak planes, and 1.55 g/cm3 when there is one weak plane, and 1.84 g/cm3 when there are two weak planes. The collapse pressure prediction model for horizontal wells proposed in this paper presented results in better agreement with those in actual situation. This model, more accurate and practical than traditional models, can effectively improve the accuracy of wellbore collapse pressure prediction of horizontal shale gas wells.

Analytical model and application of stress distribution on mining coal floor

Institute of Scientific and Technical Information of China (English)

ZHU Shu-yun; JIAN Zhen-quan; HOU Hong-liang; XIAO Wei-guo; YAO Pu

2008-01-01

Given the analysis of underground pressure, a stress calculation model of coal floor stress has been established based on a theory of elasticity. The model presents the law of stress distribution on the relatively fixed position of the mining coal floor: the extent of stress variation in a fixed floor position decreases gradually along with depth, the decreasing rate of the vertical stress is clearly larger than that of the horizontal stress at a specific depth. The direction of the maximum principal stress changes gradually from a vertical direction to a horizontal direction with the advance of the working face. The deformation and permeability of the rock mass of the coal floor are obtained by contrasting the difference of the principal stress established from theoretical calculations with curves of stress-strain and permeability-strain from tests, which is an important mechanical basis for preventing water inrush from confined aquifers.

Deformation and Failure Mechanism of Roadway Sensitive to Stress Disturbance and Its Zonal Support Technology

Directory of Open Access Journals (Sweden)

Qiangling Yao

2016-01-01

Full Text Available The 6163 haulage roadway in the Qidong coal mine passes through a fault zone, which causes severe deformation in the surrounding rock, requiring repeated roadway repairs. Based on geological features in the fault area, we analyze the factors affecting roadway deformation and failure and propose the concept of roadway sensitive to stress disturbance (RSSD. We investigate the deformation and failure mechanism of the surrounding rocks of RSSD using field monitoring, theoretical analysis, and numerical simulation. The deformation of the surrounding rocks involves dilatation of shallow rocks and separation of deep rocks. Horizontal and longitudinal fissures evolve to bed separation and fracture zones; alternatively, fissures can evolve into fracture zones with new fissures extending to deeper rock. The fault affects the stress field of the surrounding rock to ~27 m radius. Its maximum impact is on the vertical stress of the rib rock mass and its minimum impact is on the vertical stress of the floor rock mass. Based on our results, we propose a zonal support system for a roadway passing through a fault. Engineering practice shows that the deformation of the surrounding rocks of the roadway can be effectively controlled to ensure normal and safe production in the mine.

Work ability and stress in a bus transportation company in Belo Horizonte, Brazil Avaliação da capacidade para o trabalho e estresse em uma empresa de transporte coletivo de Belo Horizonte, Brasil

Directory of Open Access Journals (Sweden)

Rosana Ferreira Sampaio

2009-02-01

Full Text Available Demographic, occupational and psychosocial characteristics affect the health and occupational performance of workers. The objective of the present study was to elaborate a profile of the work ability and factors that affect it in a bus transportation company in Belo Horizonte, Brazil. The instruments used included a socio-demographic and occupational questionnaire, the Work Ability Index and the Job Stress Scale. Demographic information revealed that 85.7% of the 126 employees of the company were active workers, 98% were males, with an average of 39 years of age (SD= 10 and 79 months working in the company (SD= 68; more than half reported having a low schooling level. In terms of personal habits, 88% were exposed to one or more risk factors, especially a sedentary lifestyle. The average strain value (as a consequence of stress was 0.78 (SD= 0.2 and 75.3% reported episodes of violence at the workplace. The work ability was good to excellent among 89% of the workers. Results from the logistic regression analysis showed that strain was the only significant variable in relation to the Work Ability Index, (estimated odds ratio of 0.02. The results suggest that psychosocial factors presented the greatest association with work ability, and preventive and/or corrective measures should be implemented.Características demográficas, ocupacionais e psicossociais afetam a saúde e o desempenho dos trabalhadores. O objetivo deste estudo foi elaborar um perfil da capacidade para o trabalho e fatores que a afetam em uma empresa de transporte coletivo de Belo Horizonte, Brasil. Os instrumentos utilizados foram o Índice de Capacidade para o Trabalho, a Job Stress Scale e um questionário sociodemográfico e ocupacional. Dos 126 trabalhadores, 14,3% estavam aposentados ou afastados, todos por doença. Entre os ativos, a maioria era do sexo masculino (98%, com idade média de 39 anos (DP=10, baixa escolaridade (acima de 50% e tempo médio na empresa de 79 meses

Mud peeling and horizontal crack formation in drying clays

KAUST Repository

Style, Robert W.

2011-03-01

Mud peeling is a common phenomenon whereby horizontal cracks propagate parallel to the surface of a drying clay. Differential stresses then cause the layer of clay above the crack to curl up to form a mud peel. By treating the clay as a poroelastic solid, we analyze the peeling phenomenon and show that it is caused by the gradient in tensile stress at the surface of the clay, analogously to the spalling of thermoelastic materials. For a constant water evaporation rate at the clay surface we derive equations for the depth of peeling and the time of peeling as functions of the evaporation rate. Our model predicts a simple relationship between the radius of curvature of a mud peel and the depth of peeling. The model predictions are in agreement with the available experimental data. Copyright 2011 by the American Geophysical Union.

Stress measurements in the Naesliden Mine

Energy Technology Data Exchange (ETDEWEB)

Leijon, B. [Univ. of Luleaa, Sweden; Carlsson, H.; Myrvang, A.

1980-05-15

Determinations of virgin stresses were performed at an early stage of the Naesliden Project in order to obtain input data for the finite element models of the mine. The Leeman three-dimensional overcoring technique was used at five locations on levels ranging from 210 m to 460 m below surface. Stress data were obtained at four of these locations. The results show an excess of horizontal stresses whilst the vertical stress is in accordance with the gravitational load from the overburden. The major and intermediate principal stresses are sub-horizontal and directed respectively perpendicular and parallel to the schisotsity of the wall rock and the strike of the tabular ore body. The minor principal stress is directed almost vertically. Stresses were also measured close to a stope on 300 m level in the mine. Biaxial and triaxial overcoring measurements were made at eighteen points between 0.25 m and 7.2 m above the roof of the stope. The stresses were found to have magnitudes of about 70 MPa close to the roof and to decrease rapidly with the distance from the roof. Stress measurements were made in connection with slot blastings in the foot wall, the latter measure being made in an attempt to de-stress the roof of stope 3. Two methods were used for stress monitorings, both showing that expected stress changes did not take place. Long-term stress guages have been installed in the ore body in order to monitor expected re-distributions of stresses due to mining. So far, the recorded stress changes are below 5 MPa.

Horizontal drilling assessment in Western Canada

International Nuclear Information System (INIS)

Catania, Peter; Wilson, Malcolm

1999-01-01

The first horizontal well was drilled in Saskatchewan in 1987. Since then, the number of horizontal wells drilled has escalated rapidly, averaging approximately 500 per year since 1993. When combined with horizontal wells drilled in Alberta, the major Canadian oil-producing province, the total number drilled in 1995 was 978. This total exceeds the National Energy Board (NEB) projected maximum of 816 wells per year. The NEB projections were based on a break-even point for the drilling of horizontal wells of a return of CDN $285,000 using a discount rate of 15%. This corresponded to a cumulative production from each individual well of some 11,000 m 3 . The introduction of a royalty-free production volume of 12,000 m 3 per horizontal well in Saskatchewan was instrumental in stimulating the rapid expansion in the use of horizontal wells and helping Canada to exceed the forecasted drilling level. Within Saskatchewan, daily production from 1964 active horizontal wells is in excess of 20,000 m 3 . Comparative analysis indicates that the average daily production per well has increased from approximately by 40% with the advent of horizontal wells. In total production terms, provincial production has increased from 11.7 million cubic metres in 1989 to 20.9 million m 3 in 1996. This represents an increase of almost 79% based primarily on the extensive use of horizontal wells. In 1996, horizontal wells produced 36% of the province's oil from 12% of the active wells. In the southeastern producing areas of Saskatchewan, the Williston Basin, declining oil-production has jumped 100%, with horizontal wells accounting for approximately 50% of total regional production. Pay zones in this areas, as in most of the province, tend to be relatively thin, with net pay frequently less that 5 m. The modest investment of some CDN $5 million in government research funding 10 years ago to stimulate the development of horizontal wells, combined with a favourable royalty structure, has been at

Investigating the Influence of Regional Stress on Fault and Fracture Permeability at Pahute Mesa, Nevada National Security Site

Energy Technology Data Exchange (ETDEWEB)

Reeves, Donald M. [Desert Research Inst. (DRI), Reno, NV (United States); Smith, Kenneth D. [Univ. of Nevada, Reno, NV (United States); Parashar, Rishi [Desert Research Inst. (DRI), Reno, NV (United States); Collins, Cheryl [Desert Research Inst. (DRI), Las Vegas, NV (United States); Heintz, Kevin M. [Desert Research Inst. (DRI), Las Vegas, NV (United States)

2017-05-24

Regional stress may exert considerable control on the permeability and hydraulic function (i.e., barrier to and/or conduit for fluid flow) of faults and fractures at Pahute Mesa, Nevada National Security Site (NNSS). In-situ measurements of the stress field are sparse in this area, and short period earthquake focal mechanisms are used to delineate principal horizontal stress orientations. Stress field inversion solutions to earthquake focal mechanisms indicate that Pahute Mesa is located within a transtensional faulting regime, represented by oblique slip on steeply dipping normal fault structures, with maximum horizontal stress ranging from N29°E to N63°E and average of N42°E. Average horizontal stress directions are in general agreement with large diameter borehole breakouts from Pahute Mesa analyzed in this study and with stress measurements from other locations on the NNSS.

Geopotential Stress

DEFF Research Database (Denmark)

Schiffer, Christian; Nielsen, S.B.

Density heterogeneity in the Earth’s lithosphere causes lateral pressure variations. Horizontal gradients of the vertically integrated lithostatic pressure, the Geopotential Energy (GPE), are a source of stresses (Geopotential Stress) that contribute to the Earth’s Stress Field. In theory the GPE...... is linearly related to the lithospheric part of the Geoid. The Geopotential Stress can be calculated if either the density structure and as a consequence the GPE or the lithospheric contribution to the Geoid is known. The lithospheric Geoid is usually obtained by short pass filtering of satellite Geoid...... are not entirely suitable for the stress calculations but can be compiled and adjusted. We present an approach in which a global lithospheric density model based on CRUST2.0 is obtained by simultaneously fitting topography and surface heat flow in the presence of isostatic compensation and long-wavelength lateral...

Attempts to isolate a horizontal high diameter (300 mm nominal diameter) pipeline with an ice plug at minimum water flow and without water flow

International Nuclear Information System (INIS)

Corbescu, B.; Gyongyosi, T.; Puiu, D.; Panaitescu, V. N.

2016-01-01

The ice plug isolation technique used for high diameter horizontal pipes is used for repair and maintenance activities on hydraulic installations that use liquid working agents. These techniques do not require shutting down the entire plant. The ice plug development inside the pipe requires using custom specialized equipment for each individual application. This paper briefly describes the experimental technological facilities used for conducting the experiments and highlights the important aspects in an experiment conducted on a horizontal NPS 12 testing section running demineralized water followed by the result analysis and conclusions. The paper is dedicated to specialists working in research and technological engineering. (authors)

Crustal stress regime in Italy

Directory of Open Access Journals (Sweden)

M. Cesaro

1997-06-01

Full Text Available In order to obtain a reliable map of the present-day stress field in Italy, needed to better understand the active tectonic processes and to contribute to the assessment of seismic hazard, in 1992 we started to collect and analyze new data from borehole breakouts in deep oil and geothermal wells and focal mechanisms of earthquakes (2.5 < M <5 occurred in Italy between 1988 and 1995. From about 200 deep wells and 300 focal mechanisms analyzed to date, we infer that: the internal (SW sector of the Northern Apenninic arc is extending with minimum compressional stress (Shmin oriented ? ENE, while the external front is thrusting over the Adriatic foreland (Shmin ? NW-SE. The entire Southern Apennine is extending in NE direction (from the Tyrrhenian margin to the Apulian foreland and compression (in the foredeep is no longer active at the outer (NE thrust front. Between these two arcs, an abrupt change in the tectonic regime is detected with directions of horizontal stress changing by as much as 90º in the external front, around latitude 430N. Along the Ionian side of the Calabrian arc the stress directions inferred from breakouts and focal mechanisms are scattered with a hint of rotation from N-S Shmin close to the Southern Apennines, to ~ E-W directions in the Messina Strait. In Sicily, a NW-SE direction of SHmax is evident in the Hyblean foreland, parallel to the direction of plate motion between Africa and Europe. A more complex pattern of stress directions is observed in the thrust belt zone, with rotations from the regional trend (NW í directed SHmax to NE oriented SHmax. A predominant NW direction of SHmax is also detected in mainland Sicily from earthquake focal mechanisms, but no well data are available in this region. In the northern part of Sicily (Aeolian Islands a ~N-S direction of SHmax is observed.

Economic Integration and Quality Standards in a Duopoly Model with Horizontal and Vertical Product Differentiation

DEFF Research Database (Denmark)

Hansen, Jørgen Drud; Nielsen, Jørgen Ulff-Møller

2006-01-01

This paper examines the effects of trade barriers on quality levels in a duopoly model for two countries with one producer in each country. The products are both vertically and horizontally differentiated. In absence of quality regulation, the two producers determine prices and quality levels...... product. On the unregulated markets, integration increases welfare in both countries if they are almost of similar size. However, if the countries are very asymmetrical with respect to size, market integration may harm welfare in the large country. Welfare effects by introduction of minimum quality...

Impact of In Situ Stress Distribution Characteristics on Jointed Surrounding Rock Mass Stability of an Underground Cavern near a Hillslope Surface

Directory of Open Access Journals (Sweden)

Bangxiang Li

2017-01-01

Full Text Available In this paper, a series of numerical simulations are performed to analyze the in situ stress distribution characteristics of the rock mass near different slope angles hillslope surfaces, which are subjected to the vertical gravity stress and different horizontal lateral stresses and the influence which the in situ stress distribution characteristics of 45° hillslope to the integral stability of surrounding rock mass when an underground cavern is excavated considering three different horizontal distances from the underground cavern to the slope surface. It can be concluded from the numerical results that different slope angles and horizontal lateral stresses have a strong impact on the in situ stress distribution and the integral surrounding rock mass stability of the underground cavern when the horizontal distance from the underground cavern to the slope surface is approximately 100 m to 200 m. The relevant results would provide some important constructive suggestions to the engineering site selection and optimization of large-scale underground caverns in hydropower stations.

Do Higher Minimum Wages Benefit Health? Evidence From the UK.

Science.gov (United States)

Lenhart, Otto

This study examines the link between minimum wages and health outcomes by using the introduction of the National Minimum Wage (NMW) in the United Kingdom in 1999 as an exogenous variation of earned income. A test for health effects by using longitudinal data from the British Household Panel Survey for a period of ten years was conducted. It was found that the NMW significantly improved several measures of health, including self-reported health status and the presence of health conditions. When examining potential mechanisms, it was shown that changes in health behaviors, leisure expenditures, and financial stress can explain the observed improvements in health.

Horizontal Accelerator

Data.gov (United States)

Federal Laboratory Consortium — The Horizontal Accelerator (HA) Facility is a versatile research tool available for use on projects requiring simulation of the crash environment. The HA Facility is...

Study on collapse mechanism of junction between greatly deeper shaft and horizontal drifts (Contract research)

International Nuclear Information System (INIS)

Kurosaki, Yukio; Yamachi, Hiroshi; Katsunuma, Yoshio; Nakata, Masao; Kuwahara, Hideki; Yamada, Fumitaka; Matsushita, Kiyoshi; Sato, Toshinori

2008-03-01

The Mizunami underground research laboratory is planned to consist of greatly deeper shaft and horizontal drifts. A junction space between a greatly deeper shaft and horizontal drifts forms which would take a complicated mechanical behavior during a junction excavation. However, a quantitative design method of supporting measures for a deep junction has not yet been established. This is because a conventional shaft design has been conducted based on past experience. Detail records have not been left either in what kind of collapses and deformed phenomena occurring in shaft constructions in a past. In order to examine a collapse mechanism of greatly deeper shaft junction, we have conducted literature surveys and interview studies concerned with deep shaft construction works in a past, and investigated what collapses or difficulties had been occurred in deep shaft junctions. Considering the results of investigations with reviews of intellectuals, a collapse mechanism of a super deep shaft junction depends on both a construction procedure of shaft junction and a geological condition at great depth. During a construction of a shaft junction, stress state of rock masses near junction wall would take a complicated stress path. Especially, it should be necessary to take a most careful consideration on that tangential stress acted around a shaft wall may reduce during horizontal drift excavation. On the other hand, where greatly deeper junction intersects faults and/or fractures with a large angle, a collapse called 'Take-nuke' may occur or extraordinary earth pressure acts on a concrete wall. This is the most typical difficulties during shaft construction. In order to recognize a mechanism of these phenomena and to find out a cause of collapse generation, numerical studies that can simulate a practical rock mass behavior around a shaft junction should be carry out. We demonstrate the finite difference method is most adequate for these simulations with intellectual review

Minimum weight design of composite laminates for multiple loads

International Nuclear Information System (INIS)

Krikanov, A.A.; Soni, S.R.

1995-01-01

A new design method of constructing optimum weight composite laminates for multiple loads is proposed in this paper. A netting analysis approach is used to develop an optimization procedure. Three ply orientations permit development of optimum laminate design without using stress-strain relations. It is proved that stresses in minimum weight laminate reach allowable values in each ply with given load. The optimum ply thickness is defined at maximum value among tensile and compressive loads. Two examples are given to obtain optimum ply orientations, thicknesses and materials. For comparison purposes, calculations of stresses are done in orthotropic material using classical lamination theory. Based upon these calculations, matrix degrades at 30 to 50% of ultimate load. There is no fiber failure and therefore laminates withstand all applied loads in both examples

A novel analytical solution for estimating aquifer properties within a horizontally anisotropic aquifer bounded by a stream

Science.gov (United States)

Huang, Yibin; Zhan, Hongbin; Knappett, Peter S. K.

2018-04-01

Past studies modeling stream-aquifer interaction commonly account for vertical anisotropy in hydraulic conductivity, but rarely address horizontal anisotropy, which may exist in certain sedimentary environments. If present, horizontal anisotropy will greatly impact stream depletion and the amount of recharge a pumped aquifer captures from the river. This scenario requires a different and somewhat more sophisticated mathematical approach to model and interpret pumping test results than previous models used to describe captured recharge from rivers. In this study, a new mathematical model is developed to describe the spatiotemporal distribution of drawdown from stream-bank pumping with a well screened across a horizontally anisotropic, confined aquifer, laterally bounded by a river. This new model is used to estimate four aquifer parameters including the magnitude and directions of major and minor principal transmissivities and storativity based on the observed drawdown-time curves within a minimum of three non-collinear observation wells. In order to approve the efficacy of the new model, a MATLAB script file is programmed to conduct a four-parameter inversion to estimate the four parameters of concern. By comparing the results of analytical and numerical inversions, the accuracy of estimated results from both inversions is acceptable, but the MATLAB program sometimes becomes problematic because of the difficulty of separating the local minima from the global minima. It appears that the new analytical model of this study is applicable and robust in estimating parameter values for a horizontally anisotropic aquifer laterally bounded by a stream. Besides that, the new model calculates stream depletion rate as a function of stream-bank pumping. Unique to horizontally anisotropic and homogeneous aquifers, the stream depletion rate at any given pumping rate depends closely on the horizontal anisotropy ratio and the direction of the principle transmissivities relative to

Potential minimum cost of electricity of superconducting coil tokamak power reactors

International Nuclear Information System (INIS)

Reid, R.L.; Peng, Y-K. M.

1989-01-01

The potential minimum cost of electricity (COE) for superconducting tokamak power reactors is estimated by increasing the physics (confinement, beta limit, bootstrap current fraction) and technology [neutral beam energy, toroidal field (TF) coil allowable stresses, divertor heat flux, superconducting coil critical field, critical temperature, and quench temperature rise] constraints far beyond those assumed for ITER until the point of diminishing returns is reached. A version of the TETRA systems code, calibrated with the ITER design and modified for power reactors, is used for this analysis, limiting this study to reactors with the same basic device configuration and costing algorithms as ITER. A minimum COE is reduced from >200 to about 80 mill/kWh when the allowable design constraints are raised to 2 times those of ITER. At 4 times the ITER allowables, a minimum COE of about 60 mill/kWh is obtained. The corresponding tokamak has a major radius of approximately 4 m, a plasma current close to 10 MA, an aspect ratio of 4, a confinement H- factor ≤3, a beta limit of approximately 2 times the first stability regime, a divertor heat flux of about 20 MW/m 2 , a Β max ≤ 18 T, and a TF coil average current density about 3 times that of ITER. The design constraints that bound the minimum COE are the allowable stresses in the TF coil, the neutral beam energy, and the 99% bootstrap current (essentially free current drive). 14 refs., 4 figs., 2 tabs

Continuous Data Assimilation for a 2D Bénard Convection System Through Horizontal Velocity Measurements Alone

Science.gov (United States)

Farhat, Aseel; Lunasin, Evelyn; Titi, Edriss S.

2017-06-01

In this paper we propose a continuous data assimilation (downscaling) algorithm for a two-dimensional Bénard convection problem. Specifically we consider the two-dimensional Boussinesq system of a layer of incompressible fluid between two solid horizontal walls, with no-normal flow and stress-free boundary conditions on the walls, and the fluid is heated from the bottom and cooled from the top. In this algorithm, we incorporate the observables as a feedback (nudging) term in the evolution equation of the horizontal velocity. We show that under an appropriate choice of the nudging parameter and the size of the spatial coarse mesh observables, and under the assumption that the observed data are error free, the solution of the proposed algorithm converges at an exponential rate, asymptotically in time, to the unique exact unknown reference solution of the original system, associated with the observed data on the horizontal component of the velocity.

Numerical modeling to assess possible influence of the mine openings on far-field in-situ stress measurements at Stripa

International Nuclear Information System (INIS)

Chan, T.; Guvanasen, V.; Littlestone, N.

1981-03-01

Finite element analyses were carried out to assess the possible effects of the Stripa mine openings on the in-situ stress measured in a 400-m-deep borehole drilled from the surface. For this assessment, four 2-dimensional cases were modeled. These cases variously included two horizontal sections, and two separate, idealized vertical sections. An iron ore body in the mine was assumed to be completely extracted, thereby providing conservative estimates of stress concentration effects. Since no in-situ stress measurements were made before mining, overburden weight and horizontal stresses measured by hyrodfracturing were assumed to be the pre-mining state of stress. The stress state resulting from excavation of the mine was calculated by the finite element model. In the cases using horizontal sections, the model predicted a stress concentration factor at the borehole of approximately 1.15, which is negligible considering the difficulty of obtaining accurate stress measurements. For the vertical sections the model predicted higher stress concentration factors at depths less than 200 m. This was expected because the vertical sections chosen brought the borehole unrealistically close to the mine openings, thereby leading to overly conservative estimates. In general, deviations in the magnitudes and orientations of the calculated redistributed principal stresses from the assumed pre-mining state of stress were found to be comparable to the scatter of overcoring data. It is, therefore, recommended that, for near-field stress calculations, the vertical stress due to overburden weight and the horizontal stresses measured by hydrofracturing at the borehole be considered the unperturbed far-field in situ state of stress

Horizontal drilling under Lake Erie

Energy Technology Data Exchange (ETDEWEB)

Meller, R.

2001-07-01

Drilling oil wells under Lake Erie calls for horizontal drilling wells to be drilled from shore out into the pay-zone under the lake. The nature and characteristics of horizontal wells as compared to vertical wells are explored. Considerations that have to be taken into account in drilling horizontal wells are explained (the degree of curvature, drilling fluid quality, geosteering in the pay-zone, steering instrumentation, measurements while drilling (MWD), logging while drilling (LWD)). The concept and reasons for extended reach wells are outlined, along with characteristic features of multilateral wells.

THE FIELD OF RECENT TECTONIC STRESSES IN CENTRAL AND SOUTH-EASTERN ASIA

Directory of Open Access Journals (Sweden)

Yu. L. Rebetsky

2014-01-01

Global CMT Database, reconstructions based on the first catalog are mapped. In the maps showing consolidated patterns of the state of stresses, spacious areas of horizontal extension of the crust in Tibet are clearly identified. In the south, such areas are bordered by regions of horizontal compression of the crust in Himalaya; in the north and north-east, they are bordered by regions of horizontal shear of the crust in East Kunlun. According to results of calculations at stage 2 of the method of cataclastic analyses, the crust in the central part of Tibet is subject to intensive confining pressure and lateral compression that is reduced in the neighboring regions. The crust in the southern and northern parts of Pamir is also subject to horizontal extension and shear. Regions of horizontal compression are located to the north, west and south of Pamir. Regulations of the field of recent tectonic stresses of Tibet and Pamir, which are revealed in this study, can be explained by the concept of ‘tectonic spreading’ of these regions due to gravity, which causes intensive horizontal spreading of the crust in Himalaya when the southern boundary of Tibet bends outwards and spreads over the Indian ‘indenter’ moving in the north–north-eastern direction. It is suggested by the data on horizontal extension of the crust in Tibet and underthrusting shear stresses over the horizontal zones that the impact Indian ‘indenter’ does not go beyond the crust of Pamir and the crust of the central parts of Tibet which is located above the long-term active mantle plume.  

Sequential Indentation Tests to Investigate the Influence of Confining Stress on Rock Breakage by Tunnel Boring Machine Cutter in a Biaxial State

Science.gov (United States)

Liu, Jie; Cao, Ping; Han, Dongya

2016-04-01

The influence of confining stress on rock breakage by a tunnel boring machine cutter was investigated by conducting sequential indentation tests in a biaxial state. Combined with morphology measurements of breaking grooves and an analysis of surface and internal crack propagation between nicks, the effects of maximum confining stress and minimum stress on indentation efficiency, crack propagation and chip formation were investigated. Indentation tests and morphology measurements show that increasing a maximum confining stress will result in increased consumed energy in indentations, enlarged groove volumes and promoted indentation efficiency when the corresponding minimum confining stress is fixed. The energy consumed in indentations will increase with increase in minimum confining stress, however, because of the decreased groove volumes as the minimum confining stress increases, the efficiency will decrease. Observations of surface crack propagation show that more intensive fractures will be induced as the maximum confining stress increases, whereas the opposite occurs for an increase of minimum confining stress. An observation of the middle section, cracks and chips shows that as the maximum confining stress increases, chips tend to form in deeper parts when the minimum confining stress is fixed, whereas they tend to formed in shallower parts as the minimum confining stress increases when the maximum confining stress is fixed.

Mobilization and mixing of settled solids in horizontal storage tanks

International Nuclear Information System (INIS)

Cummins, R.L.

1995-01-01

Studies were conducted using submerged jets for the mobilization and mixing of settled solids to form a suspension that can easily be removed from storage tanks. These studies focus on the specific problems relating to horizontal, cylindrical storage tanks. Of primary consideration are the storage tanks located at the Oak Ridge National Laboratory which are used for the collection of remote-handled, radioactive liquid wastes. These wastes are in two phases. A layer of undissolved, settled solids varying from 2 to 4 feet in depth under a layer of supernate. Using a surrogate of the tank contents and an approximate 2/3 dimensional scale tank, tests were performed to determine the optimum design and location of suction and discharge nozzles as well as the minimum discharge velocity required to achieve complete mobilization of the solids in the tank

Penetrating particles in horizontal air showers

International Nuclear Information System (INIS)

Wohlenberg, J.; Boehm, E.

1975-01-01

Particle density and arrival time of muons has been measured in Horizontal Air Showers. 5,600 showers have been recorded in 7,800 hours. Using stringent selection criteria 155 showers have been found horizontal (zenith angle larger 70 0 ) in the size range 4.1 > lg N > 5.5. The muons observed in these showers can be explained by purely electromagnetic origin of horizontal showers. (orig.) [de

A new method in predicting productivity of multi-stage fractured horizontal well in tight gas reservoirs

Directory of Open Access Journals (Sweden)

Yunsheng Wei

2016-10-01

Full Text Available The generally accomplished technique for horizontal wells in tight gas reservoirs is by multi-stage hydraulic fracturing, not to mention, the flow characteristics of a horizontal well with multiple transverse fractures are very intricate. Conventional methods, well as an evaluation unit, are difficult to accurately predict production capacity of each fracture and productivity differences between wells with a different number of fractures. Thus, a single fracture sets the minimum evaluation unit, matrix, fractures, and lateral wellbore model that are then combined integrally to approximate horizontal well with multiple transverse hydraulic fractures in tight gas reservoirs. This paper presents a new semi-analytical methodology for predicting the production capacity of a horizontal well with multiple transverse hydraulic fractures in tight gas reservoirs. Firstly, a mathematical flow model used as a medium, which is disturbed by finite conductivity vertical fractures and rectangular shaped boundaries, is established and explained by the Fourier integral transform. Then the idea of a single stage fracture analysis is incorporated to establish linear flow model within a single fracture with a variable rate. The Fredholm integral numerical solution is applicable for the fracture conductivity function. Finally, the pipe flow model along the lateral wellbore is adapted to couple multi-stages fracture mathematical models, and the equation group of predicting productivity of a multi-stage fractured horizontal well. The whole flow process from the matrix to bottom-hole and production interference between adjacent fractures is also established. Meanwhile, the corresponding iterative algorithm of the equations is given. In this case analysis, the productions of each well and fracture are calculated under the different bottom-hole flowing pressure, and this method also contributes to obtaining the distribution of pressure drop and production for every

Horizontal violence in Nursing

Directory of Open Access Journals (Sweden)

Tsimoulaki Evangelia

2017-01-01

Full Text Available One’s effort to clarify the definition of horizontal labour violence is of great importance, due to the variety of definitions that are mentioned in the worldwide scientific literature. Furthermore, the reference of multiple forms of such violence herein the nurse professional group is challenging, as well. Another fact of great importance is that, any form of professional violence (horizontal violence, horizontal mobbing in the work place environment can be possibly escalated and include even physical abuse (Bullying, besides the psychological and emotional impact for the victim. The definitions of Horizontal violence, Mobbing and Bullying, include a repeated negative behaviour emanating from at least one “predator” towards at least one “victim”, with work status differences and the existence or lack of physical abuse (Bullying. Horizontal violence is a hostile, aggressive and harmful behaviour which is either overt or concealed and is pointed from an individual to another individual of the same working rank and causes intense emotional pain at the victim. The manifestations vary from humiliating tasks assignment or the victim’s efforts undermining to clearly aggressive behaviors (criticism, intimidation, sarcasm etc.. The reason behind this phenomenon is multifactorial extended not only towards the working environment but also to the personal characteristics of the “predator” as well as the possible “victim”. The researchers emphasize the high incidence of the phenomenon, as well as the cost that is induced by the violent behaviors to both the health professionals and the hospital. Finally, they point out the paradox of the presence of violence inside a system that is designed to promote health.

Beam-transport study of an isocentric rotating ion gantry with minimum number of quadrupoles

International Nuclear Information System (INIS)

Pavlovic, Marius; Griesmayer, Erich; Seemann, Rolf

2005-01-01

A beam-transport study of an isocentric gantry for ion therapy is presented. The gantry is designed with the number of quadrupoles down to the theoretical minimum, which is the feature published for the first time in this paper. This feature has been achieved without compromising the ion-optical functions of the beam-transport system that is capable of handling non-symmetric beams (beams with different emittances in vertical and horizontal plane), pencil-beam scanning, double-achromatic optics and beam-size control. Ion-optical properties of the beam-transport system are described, discussed and illustrated by computer simulations performed by the TRANSPORT-code

Horizontal steam generator thermal-hydraulics

Energy Technology Data Exchange (ETDEWEB)

Ubra, O. [SKODA Praha Company, Prague (Czechoslovakia); Doubek, M. [Czech Technical Univ., Prague (Czechoslovakia)

1995-09-01

Horizontal steam generators are typical components of nuclear power plants with pressure water reactor type VVER. Thermal-hydraulic behavior of horizontal steam generators is very different from the vertical U-tube steam generator, which has been extensively studied for several years. To contribute to the understanding of the horizontal steam generator thermal-hydraulics a computer program for 3-D steady state analysis of the PGV-1000 steam generator has been developed. By means of this computer program, a detailed thermal-hydraulic and thermodynamic study of the horizontal steam generator PGV-1000 has been carried out and a set of important steam generator characteristics has been obtained. The 3-D distribution of the void fraction and 3-D level profile as functions of load and secondary side pressure have been investigated and secondary side volumes and masses as functions of load and pressure have been evaluated. Some of the interesting results of calculations are presented in the paper.

Termination for a superconducting power transmission line including a horizontal cryogenic bushing

Science.gov (United States)

Minati, Kurt F.; Morgan, Gerry H.; McNerney, Andrew J.; Schauer, Felix

1984-01-01

A termination for a superconducting power transmission line is disclosed which is comprised of a standard air entrance insulated vertical bushing with an elbow, a horizontal cryogenic bushing linking the pressurized cryogenic cable environment to the ambient temperature bushing and a stress cone which terminates the cable outer shield and transforms the large radial voltage gradient in the cable dielectric into a much lower radial voltage gradient in the high density helium coolant at the cold end of the cryogenic bushing.

Study of the Local Horizon. (Spanish Title: Estudio del Horizonte Local.) Estudo do Horizonte Local

Science.gov (United States)

Ros, Rosa M.

2009-12-01

The study of the horizon is fundamental to easy the first observations of the students at any education center. A simple model, to be developed in each center, allows to easy the study and comprehension of the rudiments of astronomy. The constructed model is presented in turn as a simple equatorial clock, other models (horizontal and vertical) may be constructed starting from it. El estudio del horizonte es fundamental para poder facilitar las primeras observaciones de los alumnos en un centro educativo. Un simple modelo, que debe realizarse para cada centro, nos permite facilitar el estudio y la comprensión de los primeros rudimentos astronómicos. El modelo construido se presenta a su vez como un sencillo modelo de reloj ecuatorial y a partir de él se pueden construir otros modelos (horizontal y vertical). O estudo do horizonte é fundamental para facilitar as primeiras observações dos alunos num centro educativo. Um modelo simples, que deve ser feito para cada centro, permite facilitar o estudo e a compreensão dos primeiros rudimentos astronômicos. O modelo construído apresenta-se, por sua vez, como um modelo simples de relógio equatorial e a partir dele pode-se construir outros modelos (horizontal e vertical)

Estimation of global solar radiation on horizontal surfaces in Jeddah, Saudi Arabia

International Nuclear Information System (INIS)

El-Sebaii, A.A.; Al-Ghamdi, A.A.; Al-Hazmi, F.S.; Faidah, Adel S.

2009-01-01

The measured data of global solar radiation on a horizontal surface, as well as the number of sunshine hours, mean daily ambient temperature, maximum and minimum ambient temperatures, relative humidity and amount of cloud cover, for Jeddah (latitude 21 deg. 42'37''N, longitude 39 deg. 11'12''E), Saudi Arabia for the period 1996-2006 are analyzed. The data are divided into two sets. The sub-data set 1 (1996-2004) are employed to develop empirical correlations between the monthly average of daily global solar radiation fraction (H/H 0 ) and various meteorological parameters. The nonlinear Angstroem type model developed by Sen and the trigonometric function model proposed by Bulut and Bueyuekalaca are also evaluated. New empirical constants for these two models have been obtained for Jeddah. The sub-data set 2 (2005, 2006) are then used to evaluate the derived correlations. Comparisons between measured and calculated values of H have been performed. It is indicated that, the Sen and Bulut and Bueyuekalaca models satisfactorily describe the horizontal global solar radiation for Jeddah. All the proposed correlations are found to be able to predict the annual average of daily global solar radiation with excellent accuracy. Therefore, the long term performance of solar energy devices can be estimated.

Stress state and movement potential of the Kar-e-Bas fault zone, Fars, Iran

Science.gov (United States)

Sarkarinejad, Khalil; Zafarmand, Bahareh

2017-08-01

The Kar-e-Bas or Mengharak basement-inverted fault is comprised of six segments in the Zagros foreland folded belt of Iran. In the Fars region, this fault zone associated with the Kazerun, Sabz-Pushan and Sarvestan faults serves as a lateral transfer zone that accommodates the change in shortening direction from the western central to the eastern Zagros. This study evaluates the recent tectonic stress regime of the Kar-e-Bas fault zone based on inversion of earthquake focal mechanism data, and quantifies the fault movement potential of this zone based on the relationship between fault geometric characteristics and recent tectonic stress regimes. The trend and plunge of σ 1 and σ 3 are S25°W/04°-N31°E/05° and S65°E/04°-N60°W/10°, respectively, with a stress ratio of Φ = 0.83. These results are consistent with the collision direction of the Afro-Arabian continent and the Iranian microcontinent. The near horizontal plunge of maximum and minimum principle stresses and the value of stress ratio Φ indicate that the state of stress is nearly strike-slip dominated with little relative difference between the value of two principal stresses, σ 1 and σ 2. The obliquity of the maximum compressional stress into the fault trend reveals a typical stress partitioning of thrust and strike-slip motion in the Kar-e-Bas fault zone. Analysis of the movement potential of this fault zone shows that its northern segment has a higher potential of fault activity (0.99). The negligible difference between the fault-plane dips of the segments indicates that their strike is a controlling factor in the changes in movement potential.

PRESENTDAY STRESS STATE OF THE SHANXI TECTONIC BELT

Directory of Open Access Journals (Sweden)

Wang Kaiying

2012-01-01

Full Text Available The Shanxi tectonic belt is a historically earthquakeabundant area. For the majority of strong earthquakes in this area, the distribution of earthquake foci was controlled by the N–S oriented local structures on the tectonic belt. Studies of the present stress state of the Shanxi tectonic belt can contribute to the understanding of the relationship between strong earthquakes’ occurrence and their structural distribution and also facilitate assessments of regional seismic danger and determination of the regions wherein strong earthquakes may occur in future. Using the Cataclastic Analysis Method (CAM, we performed stress inversion based on the focal mechanism data of earthquakes which took place in the Shanxi tectonic belt from 1967 to 2010. Our results show that orientations of the maximum principal compressive stress axis of the Shanxi tectonic belt might have been variable before and after the 2001 Kunlun MS=8.1 strong earthquake, with two different superior trends of the NW–SE and NE–SW orientation in different periods. When the maximum principal compressive stress axis is oriented in the NE–SW direction, the pattern of the space distribution of the seismic events in the Shanxi tectonic belt shows a trend of their concentration in the N–S oriented tectonic segments. At the same time, the stress state is registered as horizontal shearing and horizontal extension in the N–S and NE–SW oriented local segments in turn. When the maximum principal compressive stress axis is NW–SE oriented, the stress state of the N–S and NE–SW oriented tectonic segments is primarily registered as horizontal shearing. Estimations of plunges of stress axes show that seismicity in the Shanxi belt  corresponds primarily to the activity of lowangle faults, and highangle stress sites are located in the NE–SW oriented extensional tectonic segments of the Shanxi belt. This indicates that the stress change of the Shanxi belt is

A plant microRNA regulates the adaptation of roots to drought stress

KAUST Repository

Chen, Hao; Li, Zhuofu; Xiong, Liming

2012-01-01

Plants tend to restrict their horizontal root proliferation in response to drought stress, an adaptive response mediated by the phytohormone abscisic acid (ABA) in antagonism with auxin through unknown mechanisms. Here, we found that stress

HORIZONTAL WELL DRILL-IN FLUIDS

Directory of Open Access Journals (Sweden)

Nediljka Gaurina-Međimurec

1998-12-01

Full Text Available Main objective of horizontal driling is to place a drain-hole for a long distance within the pay zone to enhance productivity or injectivity. In drilling horizontal wells, more serious problems appear than in drilling vertical wells. These problems are: poor hole cleaning, excessive torque and drag, hole filling, pipe stucking, wellbore instability, loss of circulation, formation damage, poor cement job, and difficulties at logging jobs. From that reason, successful drilling and production of horizontal well depends largely on the fluid used during drilling and completion phases. Several new fluids, that fulfill some or all of required properties (hole cleaning, cutting suspension, good lubrication, and relative low formation damage, are presented in this paper.

Productivity and injectivity of horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Aziz, Khalid

2000-03-06

One of the key issues addressed was pressure drop in long horizontal wells and its influence on well performance. Very little information is available in the literature on flow in pipes with influx through pipe walls. Virtually all of this work has been in small diameter pipes and with single-phase flow. In order to address this problem new experimental data on flow in horizontal and near horizontal wells have been obtained. Experiments were conducted at an industrial facility on typical 6 1/8 ID, 100 feet long horizontal well model. The new data along with available information in the literature have been used to develop new correlations and mechanistic models. Thus it is now possible to predict, within reasonable accuracy, the effect of influx through the well on pressure drop in the well.

A criterion for the onset of slugging in horizontal stratified air-water countercurrent flow

International Nuclear Information System (INIS)

Chun, Moon-Hyun; Lee, Byung-Ryung; Kim, Yang-Seok

1995-01-01

This paper presents an experimental and theoretical investigation of wave height and transition criterion from wavy to slug flow in horizontal air-water countercurrent stratified flow conditions. A theoretical formula for the wave height in a stratified wavy flow regime has been developed using the concept of total energy balance over a wave crest to consider the shear stress acting on the interface of two fluids. From the limiting condition of the formula for the wave height, a necessary criterion for transition from a stratified wavy flow to a slug flow has been derived. A series of experiments have been conducted changing the non-dimensional water depth and the flow rates of air in a horizontal pipe and a duct. Comparisons between the measured data and the predictions of the present theory show that the agreement is within ±8%

A criterion for the onset of slugging in horizontal stratified air-water countercurrent flow

Energy Technology Data Exchange (ETDEWEB)

Chun, Moon-Hyun; Lee, Byung-Ryung; Kim, Yang-Seok [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)] [and others

1995-09-01

This paper presents an experimental and theoretical investigation of wave height and transition criterion from wavy to slug flow in horizontal air-water countercurrent stratified flow conditions. A theoretical formula for the wave height in a stratified wavy flow regime has been developed using the concept of total energy balance over a wave crest to consider the shear stress acting on the interface of two fluids. From the limiting condition of the formula for the wave height, a necessary criterion for transition from a stratified wavy flow to a slug flow has been derived. A series of experiments have been conducted changing the non-dimensional water depth and the flow rates of air in a horizontal pipe and a duct. Comparisons between the measured data and the predictions of the present theory show that the agreement is within {plus_minus}8%.

Stress transmission in soil

DEFF Research Database (Denmark)

Lamandé, Mathieu; Schjønning, Per

We urgently need increased quantitative knowledge on stress transmission in real soils loaded with agricultural machinery. 3D measurements of vertical stresses under tracked wheels were performed in situ in a Stagnic Luvisol (clay content 20 %) continuously cropped with small grain cereals......). Seven load cells were inserted horizontally from a pit with minimal disturbance of soil in each of three depths (0.3, 0.6 and 0.9 m), covering the width of the wheeled area. The position of the wheel relative to the transducers was recorded using a laser sensor. Finally, the vertical stresses near...... the soil-tyre interface were measured in separate tests by 17 stress transducers across the width of the tyres. The results showed that the inflation pressure controlled the level of maximum stresses at 0.3 m depth, while the wheel load was correlated to the measured stresses at 0.9 m depth. This supports...

Biomechanical effects of two different collar implant structures on stress distribution under cantilever fixed partial dentures.

Science.gov (United States)

Merıç, Gökçe; Erkmen, Erkan; Kurt, Ahmet; Eser, Atilim; özden, Ahmet Utku

2011-11-01

The purpose of the study was to compare the effects of two distinct collar geometries of implants on stress distribution in the bone around the implants supporting cantilever fixed partial dentures (CFPDs) as well as in the implant-abutment complex and superstructures. The three-dimensional finite element method was selected to evaluate the stress distribution. CFPDs which was supported by microthread collar structured (MCS) and non-microthread collar structured (NMCS) implants was modeled; 300 N vertical, 150 N oblique and 60 N horizontal forces were applied to the models separately. The stress values in the bone, implant-abutment complex and superstructures were calculated. In the MCS model, higher stresses were located in the cortical bone and implant-abutment complex in the case of vertical load while decreased stresses in cortical bone and implant-abutment complex were noted within horizontal and oblique loading. In the case of vertical load, decreased stresses have been noted in cancellous bone and framework. Upon horizontal and oblique loading, a MCS model had higher stress in cancellous bone and framework than the NMCS model. Higher von Mises stresses have been noted in veneering material for NMCS models. It has been concluded that stress distribution in implant-supported CFPDs correlated with the macro design of the implant collar and the direction of applied force.

Determination of near surface in-situ stresses

International Nuclear Information System (INIS)

Garritty, P.; Irvin, R.

1983-06-01

One of the major unknowns affecting aspects of underground construction and the geohydrology of rock masses is the magnitude and direction of the geostatic principal stresses in the earth's crust. This is particularly the case in near surface rocks where there are indications that high horizontal stresses may exist. The techniques, experiences and results of a preliminary rock stress measurement programme conducted at shallow depth in the Carnmenellis Granite, Cornwall, using C.S.I.R.O. triaxial hollow inclusion cells are described. (author)

Performance of horizontal versus vertical vapor extraction wells

International Nuclear Information System (INIS)

Birdsell, K.H.; Roseberg, N.D.; Edlund, K.M.

1994-06-01

Vapor extraction wells used for site remediation of volatile organic chemicals in the vadose zone are typically vertical wells. Over the past few years, there has been an increased interest in horizontal wells for environmental remediation. Despite the interest and potential benefits of horizontal wells, there has been little study of the relative performance of horizontal and vertical vapor extraction wells. This study uses numerical simulations to investigate the relative performance of horizontal versus vertical vapor extraction wells under a variety of conditions. The most significant conclusion that can be drawn from this study is that in a homogeneous medium, a single, horizontal vapor extraction well outperforms a single, vertical vapor extraction well (with surface capping) only for long, linear plumes. Guidelines are presented regarding the use of horizontal wells

Optimization of the key geological target parameters of shale-gas horizontal wells in the Changning Block, Sichuan Basin

Directory of Open Access Journals (Sweden)

Hongzhi Yang

2016-12-01

Full Text Available In recent years, great progress has been made in geologic evaluation, engineering test and development optimization of the Lower Cambrian Wufeng Fm–Lower Silurian Longmaxi Fm shale gas in the Sichuan Basin, and the main shale gas exploitation technologies have been understood preliminarily. In addition, scale productivity construction has been completed in Jiaoshiba, Changning and Weiyuan blocks. In this paper, the Wufeng Fm–Longmaxi Fm shale gas wells in Changning Block were taken as the study object to provide technical reference for the development design of similar shale-gas horizontal wells. The technology combining geology with engineering, dynamic with static, and statistical analysis with simulation prediction was applied to quantify the main factors controlling shale-gas well productivity, develop the shale-gas well production prediction model, and optimize the key technical parameters of geologic target of shale-gas horizontal wells in the block (e.g. roadway orientation, location and spacing, horizontal section length and gas well production index. In order to realize high productivity of shale gas wells, it is necessary to maximize the included angle between the horizontal section orientation and the maximum major stress and fracture development direction, deploy horizontal-well roadway in top-quality shale layers, and drill the horizontal section in type I reservoirs over 1000 m long. It is concluded that high productivity of shale gas wells is guaranteed by the horizontal-well wellbore integrity and the optimized low-viscosity slickwater and ceramsite fracturing technology for complex fracture creation. Based on the research results, the technical policies for shale gas development of Changning Block are prepared and a guidance and reference are provided for the shale gas development and productivity construction in the block and the development design of similar shale-gas horizontal wells.

Global, direct and diffuse solar radiation on horizontal and tilted surfaces in Jeddah, Saudi Arabia

International Nuclear Information System (INIS)

El-Sebaii, A.A.; Al-Hazmi, F.S.; Al-Ghamdi, A.A.; Yaghmour, S.J.

2010-01-01

The measured data of global and diffuse solar radiation on a horizontal surface, the number of bright sunshine hours, mean daily ambient temperature, maximum and minimum ambient temperatures, relative humidity and amount of cloud cover for Jeddah (lat. 21 o 42'37''N, long. 39 o 11'12''E), Saudi Arabia, during the period (1996-2007) are analyzed. The monthly averages of daily values for these meteorological variables have been calculated. The data are then divided into two sets. The sub-data set I (1996-2004) are employed to develop empirical correlations between the monthly average of daily global solar radiation fraction (H/H 0 ) and the various weather parameters. The sub-data set II (2005-2007) are then used to evaluate the derived correlations. Furthermore, the total solar radiation on horizontal surfaces is separated into the beam and diffuses components. Empirical correlations for estimating the diffuse solar radiation incident on horizontal surfaces have been proposed. The total solar radiation incident on a tilted surface facing south H t with different tilt angles is then calculated using both Liu and Jordan isotropic model and Klucher's anisotropic model. It is inferred that the isotropic model is able to estimate H t more accurate than the anisotropic one. At the optimum tilt angle, the maximum value of H t is obtained as ∼36 (MJ/m 2 day) during January. Comparisons with 22 years average data of NASA SSE Model showed that the proposed correlations are able to predict the total annual energy on horizontal and tilted surfaces in Jeddah with a reasonable accuracy. It is also found that at Jeddah, the solar energy devices have to be tilted to face south with a tilt angle equals the latitude of the place in order to achieve the best performance all year round.

Implications of Nash Bargaining for Horizontal Industry Integration

OpenAIRE

Richard E. Just; Siddhartha Mitra; Sinaia Netanyahu

2005-01-01

This article shows how horizontal industry integration can arise from transferable asymmetry of technologies and endowments. The Nash bargaining solution suggests that greater technological diversity among coordinating parties yields greater gains from horizontal integration. The framework fits the case where a firm with a superior technology franchises the technology by horizontal integration. The results appear to fit hog production where integration has been primarily horizontal and, in pa...

Multi-Objective Aerodynamic and Structural Optimization of Horizontal-Axis Wind Turbine Blades

Directory of Open Access Journals (Sweden)

Jie Zhu

2017-01-01

Full Text Available A procedure based on MATLAB combined with ANSYS is presented and utilized for the multi-objective aerodynamic and structural optimization of horizontal-axis wind turbine (HAWT blades. In order to minimize the cost of energy (COE and improve the overall performance of the blades, materials of carbon fiber reinforced plastic (CFRP combined with glass fiber reinforced plastic (GFRP are applied. The maximum annual energy production (AEP, the minimum blade mass and the minimum blade cost are taken as three objectives. Main aerodynamic and structural characteristics of the blades are employed as design variables. Various design requirements including strain, deflection, vibration and buckling limits are taken into account as constraints. To evaluate the aerodynamic performances and the structural behaviors, the blade element momentum (BEM theory and the finite element method (FEM are applied in the procedure. Moreover, the non-dominated sorting genetic algorithm (NSGA II, which constitutes the core of the procedure, is adapted for the multi-objective optimization of the blades. To prove the efficiency and reliability of the procedure, a commercial 1.5 MW HAWT blade is used as a case study, and a set of trade-off solutions is obtained. Compared with the original scheme, the optimization results show great improvements for the overall performance of the blade.

Global irradiation on horizontal surface at Hyderabad, Pakistan

International Nuclear Information System (INIS)

Kalhoro, A.N.

2005-01-01

The measurement of global irradiation on horizontal surface at PCSIR (Pakistan Council of Scientific and Industrial Research) Laboratories, Hyderabad, Pakistan, for the period of January-June, 2003 is presented in this paper. During six months the total global irradiation received on horizontal surface at Hyderabad Laboratories is 1.80238 MW-h-m2. The daily irradiation data (Watt-h/Sq.m) has been collected on continuous basis by means of EPLAB Pyranometer and EPLAB Electronic Integrator provided with DIGITEC printer system. HPX- Y recorder (potentiometer) is also connected for continuous data recording of solar intensity (m V). The weather effect over the radiation income was observed regularly and proportion of sunny, cloudy, partly cloudy and dusty days is plotted. Monthly mean daily irradiation bifurcated for sunny and cloudy days are also shown separately. To give an overview of sky conditions, the monthly clearness index is calculated. The highest value of average irradiation per day was recorded in June (7.15 kW/m/sup 2/) and minimum recorded in January (4.11 kW/m/sup 2/). The summer season, although rich in radiation with long sunshine duration, brings dust storms along with many partly cloudy or cloudy days, mostly in the month of May and likely in June as well. This could be an additional barrier for solar energy applications especially in desert areas; therefore the study was made for evaluating the effect of dust on the radiation flux. The purpose of the study is the development of rural life in Pakistan such that the inhabitants of rural areas may need not to wait for the connection to national grid. This study will help in improving the efficiency of solar thermal devices, (currently fabricated on theoretical basis at the laboratories), according to experimental data. (author)

Verification of surface minimum, mean, and maximum temperature forecasts in Calabria for summer 2008

Directory of Open Access Journals (Sweden)

S. Federico

2011-02-01

Full Text Available Since 2005, one-hour temperature forecasts for the Calabria region (southern Italy, modelled by the Regional Atmospheric Modeling System (RAMS, have been issued by CRATI/ISAC-CNR (Consortium for Research and Application of Innovative Technologies/Institute for Atmospheric and Climate Sciences of the National Research Council and are available online at http://meteo.crati.it/previsioni.html (every six hours. Beginning in June 2008, the horizontal resolution was enhanced to 2.5 km. In the present paper, forecast skill and accuracy are evaluated out to four days for the 2008 summer season (from 6 June to 30 September, 112 runs. For this purpose, gridded high horizontal resolution forecasts of minimum, mean, and maximum temperatures are evaluated against gridded analyses at the same horizontal resolution (2.5 km.

Gridded analysis is based on Optimal Interpolation (OI and uses the RAMS first-day temperature forecast as the background field. Observations from 87 thermometers are used in the analysis system. The analysis error is introduced to quantify the effect of using the RAMS first-day forecast as the background field in the OI analyses and to define the forecast error unambiguously, while spatial interpolation (SI analysis is considered to quantify the statistics' sensitivity to the verifying analysis and to show the quality of the OI analyses for different background fields.

Two case studies, the first one with a low (less than the 10th percentile root mean square error (RMSE in the OI analysis, the second with the largest RMSE of the whole period in the OI analysis, are discussed to show the forecast performance under two different conditions. Cumulative statistics are used to quantify forecast errors out to four days. Results show that maximum temperature has the largest RMSE, while minimum and mean temperature errors are similar. For the period considered

Field synergy characteristics in condensation heat transfer with non-condensable gas over a horizontal tube

Directory of Open Access Journals (Sweden)

Junxia Zhang

2017-05-01

Full Text Available Field synergy characteristics in condensation heat transfer with non-condensable gas (NCG over a horizontal tube were numerically simulated. Consequently, synergy angles between velocity and pressure or temperature gradient fields, gas film layer thickness, and induced velocity and shear stress on gas–liquid interface were obtained. Results show that synergy angles between velocity and temperature gradient fields are within 73.2°–88.7° and ascend slightly with the increment in mainstream velocity and that the synergy is poor. However, the synergy angle between velocity and pressure gradient fields decreases intensively with the increase in mainstream velocity at θ ≤ 30°, thereby improving the pressure loss. As NCG mass fraction increases, the gas film layer thickness enlarges and the induced velocity and shear stress on gas–liquid interface decreases. The synergy angles between velocity and temperature gradient fields increase, and the synergy angles between velocity and pressure gradient fields change at θ = 70°, decrease at θ 70°. When the horizontal tube circumference angle increases, the synergy angles between velocity and temperature or pressure gradient fields decrease, the synergy between velocity and pressure fields enhances, and the synergy between velocity and temperature fields degrades.

Unsteady flow of an incompressible fluid in a horizontal porous medium with suction

International Nuclear Information System (INIS)

Bestman, A.R.

1988-04-01

A theoretical analysis of two-dimensional unsteady flow in a porous medium bounded by a horizontal wall is presented as a perturbation on a basic flow. It is assumed that the perturbation is occasioned by a sudden suction at the wall. Even for a highly permeable medium the characteristic Reynolds number in porous media flow is usually small and asymptotic solutions are developed by the Laplace transform technique. It is observed that the perturbed shear stress at the wall decays exponentially with time. (author). 5 refs

Small horizontal emittance in the TESLA damping ring

International Nuclear Information System (INIS)

Decking, W.

2001-01-01

The present TESLA damping ring is designed for a normalized horizontal emittance of 8x10 -6 m. γ-γ collisions at the TESLA linear collider will benefit from a further decrease of the horizontal emittance. This paper reviews the processes which limit the horizontal emittance in the damping ring. Preliminary estimates on the smallest horizontal emittance for the present TESLA damping ring design as well as an ultimate limit of the emittance reachable with the TESLA damping ring concept will be given

Stress field modelling from digital geological map data

Science.gov (United States)

Albert, Gáspár; Barancsuk, Ádám; Szentpéteri, Krisztián

2016-04-01

calculated from the fracture criterion. The calculation includes the gravitational acceleration, the average density of rocks and the experimental 60 degree of the fracture angle from the normal of the fault plane. This way, the stress tensors are calculated as absolute pressure values per square meters on both sides of the faults. If the stress from the overburden is greater than 1 bar (i.e. the faults are buried), a confined compression would be present. Modelling this state of stress may result a confusing pattern of vectors, because in a confined position the horizontal stress vectors may point towards structures primarily associated with extension. To step over this, and to highlight the variability in the stress-field, the model calculates the vectors directly from the differential stress (practically subtracting the minimum principal stress from the critical stress). The result of the modelling is a vector map, which theoretically represents the minimum tectonic pressure in the moment, when the rock body breaks from an initial state. This map - together with the original fault-map - is suitable for determining those areas where unrevealed tectonic, sedimentary and lithological structures are possibly present (e.g. faults, sub-basins and intrusions). With modelling different deformational phases on the same area, change of the stress vectors can be detected which reveals not only the varying directions of the principal stresses, but the tectonic-driven sedimentation patterns too. The decrease of necessary critical stress in the case of a possible reactivation of a fault in subsequent deformation phase can be managed with the down-ranking of the concerning structural elements. Reference: Albert G., Ungvári ZS., Szentpéteri K. 2014: Modeling the present day stress field of the Pannonian Basin from neotectonic maps - In: Beqiraj A, Ionescu C, Christofides G, Uta A, Beqiraj Goga E, Marku S (eds.) Proceedings XX Congress of the Carpathian-Balkan Geological Association

DEVELOPMENT OF COILED TUBING STRESS ANALYSIS

Directory of Open Access Journals (Sweden)

Davorin Matanović

1998-12-01

Full Text Available The use of coiled tubing is increasing rapidly with drilling of horizontal wells. To satisfy all requirements (larger mechanical stresses, larger fluid capacities the production of larger sizes and better material qualities was developed. Stresses due to axial forces and pressures that coiled tubing is subjected are close to its performance limits. So it is really important to know and understand the behaviour of coiled tubing to avoid its break, burst or collapse in the well.

The Medial Stitch in Transosseous-Equivalent Rotator Cuff Repair: Vertical or Horizontal Mattress?

Science.gov (United States)

Montanez, Anthony; Makarewich, Christopher A; Burks, Robert T; Henninger, Heath B

2016-09-01

Despite advances in surgical technique, rotator cuff repair retears continue to occur at rates of 10%, 22%, and 57% for small, medium, and large tears, respectively. A common mode of failure in transosseous-equivalent rotator cuff repairs is tissue pullout of the medial mattress stitch. While the medial mattress stitch has been studied extensively, no studies have evaluated a vertical mattress pattern placed near the musculotendinous junction in comparison with a horizontal mattress pattern. Vertical mattress stitches will have higher load to failure and lower gapping compared with horizontal mattress stitches in a transosseous-equivalent rotator cuff repair. Controlled laboratory study. Double-row transosseous-equivalent rotator cuff repairs were performed in 9 pairs of human male cadaveric shoulders (mean age ± SD, 58 ± 10 years). One shoulder in each pair received a medial-row suture pattern using a vertical mattress stitch, and the contralateral shoulder received a horizontal mattress. Specimens were mounted in a materials testing machine and tested in uniaxial tensile deformation for cyclic loading (500 cycles at 1 Hz to 1.0 MPa of effective stress), followed by failure testing carried out at a rate of 1 mm/s. Construct gapping and applied loads were monitored continuously throughout the testing. Vertical mattress sutures were placed in 5 right and 4 left shoulders. Peak cyclic gapping did not differ between vertical (mean ± SD, 2.8 ± 1.1 mm) and horizontal mattress specimens (3.0 ± 1.2 mm) (P = .684). Vertical mattress sutures failed at higher loads compared with horizontal mattress sutures (568.9 ± 140.3 vs 451.1 ± 174.3 N; P = .025); however, there was no significant difference in failure displacement (8.0 ± 1.6 vs 6.0 ± 2.1 mm; P = .092). Failure stiffness did not differ between the suture patterns (P = .204). In transosseous-equivalent rotator cuff repairs near the musculotendinous junction, a vertical mattress suture used as the medial stitch

A new formulation of mean stress effects in fatigue

Science.gov (United States)

Manson, S. S.; Heidmann, K. R.

1987-01-01

A common method of treating the mean stress effect on fatigue life is to displace the elastic line on a Manson-Coffin-Basquin diagram while retaining the position of the plastic line. Manson and Halford pointed out that this procedure implies that mean stress significantly affects the cyclic stress-strain curve. Actually, however, they showed experimentally and by more general reasoning, that mean stress has little, if any, effect on the cyclic stress-strain curve. Thus, they concluded that it is necessary to displace the plastic line as well as the elastic line in order to keep the cyclic stress-strain curve unaltered. Another way to express the common displacement of the two lines is to keep the lines in place and change the horizontal coordinate to include a term relating to the displacement. Thus, instead of life, 2N sub f, as the horizontal coordinate, a new coordinate can become 2N sub f (1-sigma sub m/sigma sub f) superscript 1/b, thereby displacing both the elastic and plastic lines by an amount (1-sigma sub m/sigma sub f) superscript 1/b where sigma sub m is the mean stress and sigma sub f is the intercept of the elastic line at N sub f = 1/2 cycles and b is the slope of the elastic line.

The stress field and its sources in the North Atlantic Realm and Europe

DEFF Research Database (Denmark)

Nielsen, S.B.; Schiffer, Christian; Stephenson, Randell Alexander

A number of sources contribute to the lithospheric stress field. Lithospheric density heterogeneities cause horizontal gradients of the vertically integrated lithostatic pressure, which give rise to gravitational/geopotential stresses. Variations of pressure, temperature and composition in the co...

Spondylolysis and the sacro-horizontal angle in athletes

International Nuclear Information System (INIS)

Swaerd, L.; Hellstroem, M.; Jacobsson, B.; Peterson, L.; Sahlgrenska Sjukhuset, Goeteborg; King Faisal Specialist Hospital and Research Centre, Riyadh

1989-01-01

The frequency of spondylolysis and the relationship between spondylolysis and the sacro-horizontal angle in 143 athletes and 30 non-athletes is reported. Athletes had a larger sacro-horizontal angle than non-athletes. The sacro-horizontal angle was larger in athletes with spondylolysis as compared with those without. An increased incidence of spondylolysis with an increased angle was demonstrated. It is suggested that an increased sacro-horizontal angle may predispose to spondylolysis, especially in combination with the high mechanical loads sustained in certain sports. (orig.)

Spondylolysis and the sacro-horizontal angle in athletes

Energy Technology Data Exchange (ETDEWEB)

Swaerd, L.; Hellstroem, M.; Jacobsson, B.; Peterson, L. (Oestra Sjukhuset, Goeteborg (Sweden). Dept. of Orthopaedics; Sahlgrenska Sjukhuset, Goeteborg (Sweden). Dept. of Diagnostic Radiology; King Faisal Specialist Hospital and Research Centre, Riyadh (Saudi Arabia). Dept. of Radiology)

The frequency of spondylolysis and the relationship between spondylolysis and the sacro-horizontal angle in 143 athletes and 30 non-athletes is reported. Athletes had a larger sacro-horizontal angle than non-athletes. The sacro-horizontal angle was larger in athletes with spondylolysis as compared with those without. An increased incidence of spondylolysis with an increased angle was demonstrated. It is suggested that an increased sacro-horizontal angle may predispose to spondylolysis, especially in combination with the high mechanical loads sustained in certain sports. (orig.).

Drop deformation and breakup in a partially filled horizontal rotating cylinder

Science.gov (United States)

White, Andrew; Pereira, Caroline; Hyacinthe, Hyaquino; Ward, Thomas

2014-11-01

Drop deformation and breakup due to shear flow has been studied extensively in Couette devices as well as in gravity-driven flows. In these cases shear is generated either by the moving wall or the drop's motion. For such flows the drop shape remains unperturbed at low capillary number (Ca), deforms at moderate Ca , and can experience breakup as Ca --> 1 and larger. Here single drops of NaOH(aq) will be placed in a horizontal cylindrical rotating tank partially filled with vegetable oil resulting in 10-2 saponification, can yield lower minimum surface tensions and faster adsorption than non-reactive surfactant systems. Oil films between the wall and drop as well as drop shape will be observed as rotation rates and NaOH(aq) concentration are varied. Results will be presented in the context of previous work on bubble and drop shapes and breakup. NSF CBET #1262718.

Horizontal alveolar bone loss: A periodontal orphan

Science.gov (United States)

Jayakumar, A.; Rohini, S.; Naveen, A.; Haritha, A.; Reddy, Krishnanjeneya

2010-01-01

Background: Attempts to successfully regenerate lost alveolar bone have always been a clinician’s dream. Angular defects, at least, have a fairer chance, but the same cannot be said about horizontal bone loss. The purpose of the present study was to evaluate the prevalence of horizontal alveolar bone loss and vertical bone defects in periodontal patients; and later, to correlate it with the treatment modalities available in the literature for horizontal and vertical bone defects. Materials and Methods: The study was conducted in two parts. Part I was the radiographic evaluation of 150 orthopantomographs (OPGs) (of patients diagnosed with chronic periodontitis and seeking periodontal care), which were digitized and read using the AutoCAD 2006 software. All the periodontitis-affected teeth were categorized as teeth with vertical defects (if the defect angle was ≤45° and defect depth was ≥3 mm) or as having horizontal bone loss. Part II of the study comprised search of the literature on treatment modalities for horizontal and vertical bone loss in four selected periodontal journals. Results: Out of the 150 OPGs studied, 54 (36%) OPGs showed one or more vertical defects. Totally, 3,371 teeth were studied, out of which horizontal bone loss was found in 3,107 (92.2%) teeth, and vertical defects were found only in 264 (7.8%) of the teeth, which was statistically significant (P<.001). Search of the selected journals revealed 477 papers have addressed the treatment modalities for vertical and horizontal types of bone loss specifically. Out of the 477 papers, 461 (96.3%) have addressed vertical bone loss, and 18 (3.7%) have addressed treatment options for horizontal bone loss. Two papers have addressed both types of bone loss and are included in both categories. Conclusion: Horizontal bone loss is more prevalent than vertical bone loss but has been sidelined by researchers as very few papers have been published on the subject of regenerative treatment modalities for

comparative evaluation of pressure distribution between horizontal

African Journals Online (AJOL)

user

This paper presents comparative analysis between the pressure behavior of ... Green and source function were used to evaluate the performance of horizontal well and ..... Superscript. ' derivative. D = dimensionless. h = horizontal. = change.

Laboratory testing and field implementation of scale inhibitor squeeze treatments to subsea and platform horizontal wells, North Sea Basin

Energy Technology Data Exchange (ETDEWEB)

Jordan, M. M.; Lewis, M. [Nalco/Exxon Energy Chemicals Ltd, Aberdeen (United Kingdom); Tomlinson, C. J.; Pritchard, A. R. P. [Enterprise Oil Plc, Aberdeen (United Kingdom)

1998-12-31

Field results from a number of scale squeeze treatments carried out on subsea and platform horizontal wells in the Nelson Field of the North Sea are presented. Scale inhibitor chemicals are reviewed along with factors which influence inhibitor selection for both horizontal and highly deviated wells. Formation brine/inhibitor incompatibility, formation minerals/inhibitor incompatibility, and the potential for sand production and oil-in-water process as a result of these incompatibilities, are discussed. Practical difficulties in squeezing subsea horizontal wells, the use of chemical stabilizers to reduce formation brine/inhibitor incompatibility, variation of pump rates to encourage propagation of inhibitor along the wellbore, and the potential of fluid diversion are outlined, stressing the significance of production logging data (or good reservoir simulation data), to evaluate the location of water production prior to the squeeze treatment. Results of these treatments show that with the correct laboratory evaluation of both scale inhibitor and divertor agents, and with appropriate utilization of production logging or reservoir simulation data, it is possible to carry out scale inhibitor squeeze treatments of subsea and platform horizontal wells without having to resort to coiled tubing. 22 refs., 1 tab., 14 figs

Do Minimum Wages Fight Poverty?

OpenAIRE

David Neumark; William Wascher

1997-01-01

The primary goal of a national minimum wage floor is to raise the incomes of poor or near-poor families with members in the work force. However, estimates of employment effects of minimum wages tell us little about whether minimum wages are can achieve this goal; even if the disemployment effects of minimum wages are modest, minimum wage increases could result in net income losses for poor families. We present evidence on the effects of minimum wages on family incomes from matched March CPS s...

The development of Canadian leadership in horizontal drilling technology

Energy Technology Data Exchange (ETDEWEB)

Hawkins, J R

1989-01-01

Horizontal wells are of increasing interest in the oil and gas industry, as is evident from the increase in the numbers of such wells being drilled. Horizontal well technology is used to improve production rates, notably in low permeability formations; to capture reserves if a reservoir is not economic using non-horizontal wells; to manage breakthrough of sweep fluids and increase sweep efficiency; and to extend the areal reach from a single surface location, especially in offshore production. The types of horizontal wells, differentiated on the basis of how quickly the well becomes horizontal, are briefly outlined and a short history of horizontal wells is presented. Canadian accomplishments in this field are then described, including steerable drilling systems, measurement-while-drilling systems, management of hole drag and torque, and well completion techniques. About 25 horizontal wells are forecast to be drilled in Canada in 1989, indicating the favorable future of this technology. 2 figs., 5 tabs.

Elastic stress transmission and transformation (ESTT) by confined liquid: A new mechanics for fracture in elastic lithosphere of the earth

Science.gov (United States)

Xu, Xing-Wang; Peters, Stephen; Liang, Guang-He; Zhang, Bao-Lin

2016-01-01

We report on a new mechanical principle, which suggests that a confined liquid in the elastic lithosphere has the potential to transmit a maximum applied compressive stress. This stress can be transmitted to the internal contacts between rock and liquid and would then be transformed into a normal compressive stress with tangential tensile stress components. During this process, both effective compressive normal stress and tensile tangential stresses arise along the liquid–rock contact. The minimum effective tensile tangential stress causes the surrounding rock to rupture. Liquid-driven fracture initiates at the point along the rock–liquid boundary where the maximum compressive stress is applied and propagates along a plane that is perpendicular to the minimum effective tensile tangential stress and also is perpendicular to the minimum principal stress.

The horizontal plane appearances of scoliosis

DEFF Research Database (Denmark)

Illés, Tamás S.; Burkus, Máté; Somoskeőy, Szabolcs

2017-01-01

Purpose: A posterior-anterior vertebral vector is proposed to facilitate visualization and understanding of scoliosis. The aim of this study was to highlight the interest of using vertebral vectors, especially in the horizontal plane, in clinical practice. Methods: We used an EOS two-/three-dimen......Purpose: A posterior-anterior vertebral vector is proposed to facilitate visualization and understanding of scoliosis. The aim of this study was to highlight the interest of using vertebral vectors, especially in the horizontal plane, in clinical practice. Methods: We used an EOS two...... cases of a normal spine and a thoracic scoliosis are presented. Results: For a normal spine, vector projections in the transverse plane are aligned with the posterior-anterior anatomical axis. For a scoliotic spine, vector projections in the horizontal plane provide information on the lateral...... decompensation of the spine and the lateral displacement of vertebrae. In the horizontal plane view, vertebral rotation and projections of the sagittal curves can also be analyzed simultaneously. Conclusions: The use of posterior-anterior vertebral vector facilitates the understanding of the 3D nature...

Oxidative stress in deep scattering layers: Heat shock response and antioxidant enzymes activities of myctophid fishes thriving in oxygen minimum zones

Science.gov (United States)

Lopes, Ana Rita; Trübenbach, Katja; Teixeira, Tatiana; Lopes, Vanessa M.; Pires, Vanessa; Baptista, Miguel; Repolho, Tiago; Calado, Ricardo; Diniz, Mário; Rosa, Rui

2013-12-01

Diel vertical migrators, such as myctophid fishes, are known to encounter oxygen minimum zones (OMZ) during daytime in the Eastern Pacific Ocean and, therefore, have to cope with temperature and oxidative stress that arise while ascending to warmer, normoxic surface waters at night-time. The aim of this study was to investigate the antioxidant defense strategies and heat shock response (HSR) in two myctophid species, namely Triphoturus mexicanus and Benthosema panamense, at shallow and warm surface waters (21 kPa, 20-25 °C) and at hypoxic, cold (≤1 kPa, 10 °C) mesopelagic depths. More specifically, we quantified (i) heat shock protein concentrations (HSP70/HSC70) (ii) antioxidant enzyme activities [including superoxide dismutase (SOD), catalase (CAT) and glutathione-S-transferase (GST)], and (iii) lipid peroxidation [malondialdehyde (MDA) levels]. HSP70/HSC70 levels increased in both myctophid species at warmer, well-oxygenated surface waters probably to prevent cellular damage (oxidative stress) due to increased oxygen demand under elevated temperatures and reactive oxygen species (ROS) formation. On the other hand, CAT and GST activities were augmented under hypoxic conditions, probably as preparatory response to a burst of oxyradicals during the reoxygenation phase (while ascending). SOD activity decreased under hypoxia in B. panamense, but was kept unchanged in T. mexicanus. MDA levels in B. panamense did not change between the surface and deep-sea conditions, whereas T. mexicanus showed elevated MDA and HSP70/HSC70 concentrations at warmer surface waters. This indicated that T. mexicanus seems to be not so well tuned to temperature and oxidative stress associated to diel vertical migrations. The understanding of such physiological strategies that are linked to oxygen deprivation and reoxygenation phases may provide valuable information about how different species might respond to the impacts of environmental stressors (e.g. expanding mesopelagic hypoxia

Semi-integration of overcoring stress data and review of rock stress data at the Olkiluoto site

International Nuclear Information System (INIS)

Ask, D.

2011-06-01

This project involves a semi-integration of collected rock stress data at Olkiluoto. The data included in the study involves overcoring and hydraulic fracturing data reported in the 2006 Site Report, supplemented with the additional data gathered since then, measurements for the power plant construction, and measurements in ONKALO. Despite the extensive data, and although the data display a fair correspondence with respect to stress magnitudes between methods, a few discrepancies between methods exist. The discrepancies primarily concern the orientation of the horizontal stresses and the magnitude of maximum horizontal stress. The objective of the study is help answer the remaining discrepancies in the collected data using a semi-integration approach on the overcoring data, i.e. a simplified application of the Integrated Stress Determination Method. The semi-integration involves two steps: (i) a brief re-evaluation of data; and (ii) forced overcoring stress calculations based on constraints derived from the other stress measurement techniques. The overall intension was to force overcoring data, which is the method displaying the largest scatter in results at the Olkiluoto site, to be consistent with a number of constraints that were derived from other stress measurement techniques. This exercise would outline the most probable constraints and in the extension, help identifying a stress model for the site. Regrettably, the results of the semi-integration were not completely satisfactory. The most important factor of this outcome is believed to be the failure to reduce the initial scatter through a re-evaluation. The remaining scatter after re-evaluation is judged too large to represent solely in situ stress variation; hence, measurement related errors are likely still present in the re-evaluated data set. A more in-depth analysis may to some extent decrease the scatter in data, but perhaps more effectively, develop a tool that simultaneously can derive the stress

Horizontal drilling in Miocene thin sand of Lake Maracaibo

Energy Technology Data Exchange (ETDEWEB)

Partidas, C. [PDVSA Exploration and Production (Venezuela)

1998-12-31

Horizontal drilling in the mature Lake Maracaibo field in Venezuela as a means of stimulating production are discussed. The Miocene sand where the horizontal well technology was applied, presented a number of intervals of unconsolidated sand of varied continuity, pay intervals at ten to twenty feet thickness, and reservoir pressures mostly at hydrostatic or below hydrostatic values. This paper evaluates a horizontal drilling program in the Lagunallis Lago Production Unit of Maracaibo, involving 91 wells to date (since 1995). When assessed in economic terms, results indicate that horizontal wells are a better economic alternative than vertical wells. The same results also showed that drainage from thin sand reservoirs resulted in better production with horizontal well technology than production from vertical wells. Payout was less than two years for 50 per cent of the horizontal wells while 40 per cent had payouts of between two and four years. Profit to investment ratio was greater than two in the case of about 70 per cent of the horizontal wells drilled in 1996. 2 tabs., 10 figs.

Compressive residual stresses as a preventive measure against stress corrosion cracking on turbine components

International Nuclear Information System (INIS)

Berger, C.; Ewald, J.; Fischer, K.; Gruendler, O.; Potthast, E.; Stuecker, E.; Winzen, G.

1987-01-01

Disk type low pressure turbine rotors have been designed for a large variety of power plant applications. Developing disk type rotors required a concerted effort to design a shaft/disk shrink fit with a minimum of tensile stress concentrations in order to aim for the lowest possible susceptibility to corrosive attack, i.e. stress corrosion cracking. As a result of stresses, the regions of greatest concern are the shrink fit boundaries and the keyways of turbine disks. These stresses are caused by service loading, i.e. centrifugal and shrinkage stresses and by manufacturing procedure, i.e. residual stresses. The compressive residual stresses partly compensate the tensile service stresses so that an increase of compressive residual stresses decreases the whole stress state of the component. Special manufacturing procedures, e.g. accelerated cooling after tempering can induce compressive residual stresses up to about 400 MPa in the hub bore region of turbine disk

A method for evaluating horizontal well pumping tests.

Science.gov (United States)

Langseth, David E; Smyth, Andrew H; May, James

2004-01-01

Predicting the future performance of horizontal wells under varying pumping conditions requires estimates of basic aquifer parameters, notably transmissivity and storativity. For vertical wells, there are well-established methods for estimating these parameters, typically based on either the recovery from induced head changes in a well or from the head response in observation wells to pumping in a test well. Comparable aquifer parameter estimation methods for horizontal wells have not been presented in the ground water literature. Formation parameter estimation methods based on measurements of pressure in horizontal wells have been presented in the petroleum industry literature, but these methods have limited applicability for ground water evaluation and are based on pressure measurements in only the horizontal well borehole, rather than in observation wells. This paper presents a simple and versatile method by which pumping test procedures developed for vertical wells can be applied to horizontal well pumping tests. The method presented here uses the principle of superposition to represent the horizontal well as a series of partially penetrating vertical wells. This concept is used to estimate a distance from an observation well at which a vertical well that has the same total pumping rate as the horizontal well will produce the same drawdown as the horizontal well. This equivalent distance may then be associated with an observation well for use in pumping test algorithms and type curves developed for vertical wells. The method is shown to produce good results for confined aquifers and unconfined aquifers in the absence of delayed yield response. For unconfined aquifers, the presence of delayed yield response increases the method error.

Literature review of the benefits and obstacle of horizontal directional drilling

Science.gov (United States)

Norizam, M. S. Mohd; Nuzul Azam, H.; Helmi Zulhaidi, S.; Aziz, A. Abdul; Nadzrol Fadzilah, A.

2017-11-01

In this new era the construction industry not only need to be completed within budget, timely, at acceptable quality and safety but the stakeholders especially the local authorities and the public realises for the important need of sustainable construction method to be used for our younger generation to heritage if not better a safer world for them to live and raise up their children’s. Horizontal Directional Drilling method is the most commonly recognised trenchless utilities method as a preferred construction method in this age. Among the reasons HDD method offers less disturbance on traffic, the public, business activities and neighbourhood, lower restoration cost, less noise, dust and minimum import/export of the construction materials. In addition HDD method can drill through congested utilities areas with minimum cutting and shorter time. This paper aims to appraise the benefits and obstacle of HDD method in construction industry. It is an endeavour to fulfil the local authorities cry for alternative method that less damages to the roads, road furniture’s and public complaints compared to the conventional open cut method. In addition HDD method is seem to be in line with sustainable development requirements e.g. reduce, reuse, recycle and etc. Hence, it is important to determine the benefits and obstacle factors of HDD implementation. The factors are based on the literature review conducted by the author on the subject matters gathered from previous studies, journals, text books, guidelines, magazine articles, newspaper cutting and etc.

Benefits of a horizontal well in sandstone waterflood

International Nuclear Information System (INIS)

Hansen, K.L.

1992-01-01

This is a case study which describes the planning and results of a horizontal well in a shallow Wilcox sandstone waterflood unit in central Louisiana. The Tremont H-13-1 was OXY USA Inc.'s first horizontal well. Analysis will include examination of the selection criteria, planning, execution, completion, and production. A variety of well and field data is presented and reviewed to access the value of this information as it applies towards other applications. The Cruse Waterflood Unit is a 2100 ft. Wilcox formation in central Louisiana. Production improvements have been 500% or greater for the horizontal well versus adjacent vertical wells. The horizontal well paid out in less than 4 months Results from this well indicate that not only was this project an economic success, but that other fields will similar conditions can be produced in a more profitable manner with horizontal wells

Stress studies in EFG

Science.gov (United States)

1983-01-01

Stress distributions were calculated for a creep law to predict a rate of plastic deformation. The expected reduction in stresses is obtained. Improved schemes for calculating growth system temperature distributions were evaluated. Temperature field modeling examined the possibility of using horizontal temperature gradients to influence stress distribution in ribbon. The defect structure of 10 cm wide ribbon grown in the cartridge system was examined. A new feature is identified from an examination of cross sectional micrographs. It consists of high density dislocation bands extending through the ribbon thickness. A four point bending apparatus was constructed for high temperature study of the creep response of silicon, to be used to generate defects for comparison with as grown defects in ribbon. The feasibility of laser interferometric techniques for sheet residual stress distribution measurement is examined. The mathematical formalism for calculating residual stress from changes in surface topology caused by an applied stress in a rectangular specimen was developed, and the system for laser interferometric measurement to obtain surface topology data was tested on CZ silicon.

The Process of Horizontal Differentiation: Two Models.

Science.gov (United States)

Daft, Richard L.; Bradshaw, Patricia J.

1980-01-01

Explores the process of horizontal differentiation by examining events leading to the establishment of 30 new departments in five universities. Two types of horizontal differentiation processes--administrative and academic--were observed and each was associated with different organizational conditions. (Author/IRT)

Horizontal Conflict Resolution Maneuvers with a Cockpit Display of Traffic Information

Science.gov (United States)

Palmer, E.; Jago, S.; Dubord, M.

1981-01-01

Pilot resolution of potential conflicts in the horizontal plane when the only information available on the other aircraft was presented on a Cockpit Display of Traffic Information (CDTI) is investigated. The pilot's task was to assess the situation and if necessary maneuver so as to avoid the other aircraft. No instructions were given on evasive strategy or on what was considered to be an acceptable minimum separation. The results indicate that pilots had a strong bias of turning toward the intruder aircraft in order to pass behind it. In more than 50% of the encounters with a 90 degree crossing angle in which the intruder aircraft was programmed to pass behind the aircraft, the pilots maneuvered so as to pass behind the intruder. This bias was not as strong with the display which showed a prediction of the intruder's relative velocity. The average miss distance for all encounters was about 4500 feet.

Active faults paragenesis and the state of crustal stresses in the Late Cenozoic in Central Mongolia

Directory of Open Access Journals (Sweden)

V. A. Sankov

2015-01-01

Full Text Available Active faults of the Hangay-Hentiy tectonic saddle region in Central Mongolia are studied by space images interpretation, relief analysis, structural methods and tectonic stress reconstruction. The study results show that faults activation during the Late Cenozoic stage was selective, and a cluster pattern of active faults is typical for the study region. Morphological and genetic types and the kinematics of faults in the Hangay-Hentiy saddle region are related the direction of the ancient inherited structural heterogeneities. Latitudinal and WNW trending faults are left lateral strike-slips with reverse or thrust component (Dzhargalantgol and North Burd faults. NW trending faults are reverse faults or thrusts with left lateral horizontal component. NNW trending faults have right lateral horizontal component. The horizontal component of the displacements, as a rule, exceeds the vertical one. Brittle deformations in fault zones do not conform with the Pliocene and, for the most part, Pleistocene topography. With some caution it may be concluded that the last phase of revitalization of strike slip and reverse movements along the faults commenced in the Late Pleistocene. NE trending disjunctives are normal faults distributed mainly within the Hangay uplift. Their features are more early activation within the Late Cenozoic and the lack of relation to large linear structures of the previous tectonic stages. According to the stress tensor reconstructions of the last phase of deformation in zones of active faults of the Hangay-Hentiy saddle using data on tectonic fractures and fault displacements, it is revealed that conditions of compression and strike-slip with NNE direction of the axis of maximum compression were dominant. Stress tensors of extensional type with NNW direction of minimum compression are reconstructed for the Orkhon graben. It is concluded that the activation of faults in Central Mongolia in the Pleistocene-Holocene, as well as

Investigation of the influence of wall stiffness on the stress ratio in mammoth silos

NARCIS (Netherlands)

van Leeuwenstijn, P.L.L.; van Leeuwenstijn, P.L.L.; van Wijk, L.A.; van Wijk, L.A.; Haaker, G.

1994-01-01

To calculate the stresses on the walls of silos, it is necessary to have a good estimate of the ratio of horizontal to vertical stress. This ratio however is not known precisely, especially in cases of static stress as found in a mammoth silo. In this paper the influence of the wall stiffness on the

Minimum-fuel turning climbout and descent guidance of transport jets

Science.gov (United States)

Neuman, F.; Kreindler, E.

1983-01-01

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Stress measurements in the Stripa granite. Technical project report No. 4

International Nuclear Information System (INIS)

Carlsson, H.

1978-08-01

Rock stress measurements at the 348 m level of the Stripa Mine have been carried out with the Leeman tri-axial equipment. The largest principal stress is found to be 20.0 MPa and directed parallel with the strike of the contact between the granite and the orebody. The intermediate principal stress is 11.4 MPa and directed almost horizontal and perpendicular to the contact. The minor principal stress has a magnitude of 5.4 MPa. The deduced vertical stress is approximately of the same value as can be theoretically calculated

Variability of the inclination of anatomic horizontal reference planes of the craniofacial complex in relation to the true horizontal line in orthognathic patients.

Science.gov (United States)

Zebeib, Ameen M; Naini, Farhad B

2014-12-01

The purpose of this study was to assess the reliability of the Frankfort horizontal (FH), sella-nasion horizontal, and optic planes in terms of their variabilities in relation to a true horizontal line in orthognathic surgery patients. Thirty-six consecutive presurgical orthognathic patients (13 male, 23 female; age range, 16-35 years; 30 white, 6 African Caribbean) had lateral cephalometric radiographs taken in natural head position, with a plumb line orientating the true vertical line, and the true horizontal line perpendicular to the true vertical. The inclinations of the anatomic reference planes were compared with the true horizontal. The FH plane was found to be on average closest to the true horizontal, with a mean of -1.6° (SD, 3.4°), whereas the sella-nasion horizontal and the optic plane had means of 2.1° (SD, 5.1°) and 3.2° (SD, 4.7°), respectively. The FH showed the least variability of the 3 anatomic planes. The ranges of variability were high for all anatomic planes: -8° to 8° for the FH, -8° to 15° for the sella-nasion horizontal, and -6° to 13° for the optic plane. No significant differences were found in relation to patients' sex, skeletal patterns, or ethnic backgrounds. The clinically significant variability in the inclinations of anatomic reference planes in relation to the true horizontal plane makes their use unreliable in orthognathic patients. Copyright © 2014 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Stress variations during a glacial cycle at 500 m depth in Forsmark and Oskarshamn: Earth model effects

Energy Technology Data Exchange (ETDEWEB)

Lund, Bjoern [Uppsala Univ. (Sweden). Dept. of Earth Sciences

2006-06-15

This study has considered the response to a glaciation of Earth models of increasingly complex structure in elastic parameters and viscosity. The models are one-dimensional in the sense that they vary only in the depth direction, i.e. there are only uniform, horizontal layers in the models. I find that as the complexity of the models increase, and the properties of the uppermost kilometer of the Earth become less affected by average properties from deeper down, the flexural stresses at 500 m depth decrease, as expected. A lower Young's modulus, lower compressibility and lower density in the uppermost layer all act to lower the stresses. However, the three properties act differently on the resulting response. Introducing layering in Young's modulus generally decreases the stresses all along a profile through the ice model. Going from incompressible to compressible models affect the stresses outside the ice edge significantly more than the stresses under the ice sheet. Introducing layering in density conversely affect the stresses under the ice sheet more than those outside the ice edge. The combined effects of the most complex models tested here show that the glacially induced horizontal stresses at 500 m depth decrease to levels very similar in magnitude to the loading stress. There are, however, temporal variations in these horizontal stresses that do not follow the loading stress and which induce tensional or compressional horizontal stresses that persist when no ice is present.As is well known, changes in viscosity structure has a very large effect on the Earth response. Viscosity affect both the magnitudes of the induced stresses and the temporal behavior of the stress evolution. This is confirmed in the current study.The glacially induced stresses for some of the models have been used in combination with the current background stress field at Forsmark and Oskarshamn, as estimated in SKB's site models, to evaluate fault stability throughout a

Stress variations during a glacial cycle at 500 m depth in Forsmark and Oskarshamn: Earth model effects

International Nuclear Information System (INIS)

Lund, Bjoern

2006-06-01

This study has considered the response to a glaciation of Earth models of increasingly complex structure in elastic parameters and viscosity. The models are one-dimensional in the sense that they vary only in the depth direction, i.e. there are only uniform, horizontal layers in the models. I find that as the complexity of the models increase, and the properties of the uppermost kilometer of the Earth become less affected by average properties from deeper down, the flexural stresses at 500 m depth decrease, as expected. A lower Young's modulus, lower compressibility and lower density in the uppermost layer all act to lower the stresses. However, the three properties act differently on the resulting response. Introducing layering in Young's modulus generally decreases the stresses all along a profile through the ice model. Going from incompressible to compressible models affect the stresses outside the ice edge significantly more than the stresses under the ice sheet. Introducing layering in density conversely affect the stresses under the ice sheet more than those outside the ice edge. The combined effects of the most complex models tested here show that the glacially induced horizontal stresses at 500 m depth decrease to levels very similar in magnitude to the loading stress. There are, however, temporal variations in these horizontal stresses that do not follow the loading stress and which induce tensional or compressional horizontal stresses that persist when no ice is present.As is well known, changes in viscosity structure has a very large effect on the Earth response. Viscosity affect both the magnitudes of the induced stresses and the temporal behavior of the stress evolution. This is confirmed in the current study.The glacially induced stresses for some of the models have been used in combination with the current background stress field at Forsmark and Oskarshamn, as estimated in SKB's site models, to evaluate fault stability throughout a glacial cycle. The

Horizontal well impact on heavy oil supply

International Nuclear Information System (INIS)

Bowers, B.; Bielecki, J.; Hu, J.; Wall, B.; Drummond, K.

1993-01-01

Horizontal wells can take advantage of gravity drainage mechanisms, which can be important in conventional heavy oil and bitumen recovery. Horizontal drilling will impact on the development of established conventional heavy oil pools by infill drilling and application of enhanced recovery techniques. There will also be an impact on the development of extensions to established and newly discovered heavy oil pools, as well as a major impact on development of bitumen resources. To assess the impact of horizontal drilling on heavy oil supply, high-impact and low-impact scenarios were evaluated under specified oil-price assumptions for four heavy oil areas in Saskatchewan and Alberta. Horizontal well potential for infill drilling, waterflood projects, and thermal projects was assessed and estimates were made of such developments as reserves additions and heavy oil development wells under the two scenarios. In the low case, projected supply of conventional heavy oil and bitumen stabilizes at a level in the 90,000-94,000 m 3 /d after 1994. In the high case, overall supply continuously grows from 80,000 m 3 /d in 1992 to 140,000 m 3 /d in 2002. Through application of horizontal drilling, reserves additions in western Canada could be improved by ca 100 million m 3 by 2002. 14 figs., 6 tabs

Rising above the Minimum Wage.

Science.gov (United States)

Even, William; Macpherson, David

An in-depth analysis was made of how quickly most people move up the wage scale from minimum wage, what factors influence their progress, and how minimum wage increases affect wage growth above the minimum. Very few workers remain at the minimum wage over the long run, according to this study of data drawn from the 1977-78 May Current Population…

Horizontal bridges in polar dielectric liquids

Science.gov (United States)

Woisetschläger, Jakob; Wexler, Adam D.; Holler, Gert; Eisenhut, Mathias; Gatterer, Karl; Fuchs, Elmar C.

2012-01-01

When a high-voltage direct-current is applied to two beakers filled with polar liquid dielectrica like water or methanol, a horizontal bridge forms between the two beakers. By repeating a version of Pellat's experiment, it is shown that a horizontal bridge is stable by the action of electrohydrodynamic pressure. Thus, the static and dynamic properties of the phenomenon called a `floating water bridge' can be explained by the gradient of Maxwell pressure, replenishing the liquid within the bridge against any drainage mechanism. It is also shown that a number of liquids can form stable and long horizontal bridges. The stability of such a connection, and the asymmetry in mass flow through such bridges caused by the formation of ion clouds in the vicinity of the electrodes, is also discussed by two further experiments.

Reference respiratory waveforms by minimum jerk model analysis

Energy Technology Data Exchange (ETDEWEB)

Anetai, Yusuke, E-mail: anetai@radonc.med.osaka-u.ac.jp; Sumida, Iori; Takahashi, Yutaka; Yagi, Masashi; Mizuno, Hirokazu; Ogawa, Kazuhiko [Department of Radiation Oncology, Osaka University Graduate School of Medicine, Yamadaoka 2-2, Suita-shi, Osaka 565-0871 (Japan); Ota, Seiichi [Department of Medical Technology, Osaka University Hospital, Yamadaoka 2-15, Suita-shi, Osaka 565-0871 (Japan)

2015-09-15

Purpose: CyberKnife{sup ®} robotic surgery system has the ability to deliver radiation to a tumor subject to respiratory movements using Synchrony{sup ®} mode with less than 2 mm tracking accuracy. However, rapid and rough motion tracking causes mechanical tracking errors and puts mechanical stress on the robotic joint, leading to unexpected radiation delivery errors. During clinical treatment, patient respiratory motions are much more complicated, suggesting the need for patient-specific modeling of respiratory motion. The purpose of this study was to propose a novel method that provides a reference respiratory wave to enable smooth tracking for each patient. Methods: The minimum jerk model, which mathematically derives smoothness by means of jerk, or the third derivative of position and the derivative of acceleration with respect to time that is proportional to the time rate of force changed was introduced to model a patient-specific respiratory motion wave to provide smooth motion tracking using CyberKnife{sup ®}. To verify that patient-specific minimum jerk respiratory waves were being tracked smoothly by Synchrony{sup ®} mode, a tracking laser projection from CyberKnife{sup ®} was optically analyzed every 0.1 s using a webcam and a calibrated grid on a motion phantom whose motion was in accordance with three pattern waves (cosine, typical free-breathing, and minimum jerk theoretical wave models) for the clinically relevant superior–inferior directions from six volunteers assessed on the same node of the same isocentric plan. Results: Tracking discrepancy from the center of the grid to the beam projection was evaluated. The minimum jerk theoretical wave reduced the maximum-peak amplitude of radial tracking discrepancy compared with that of the waveforms modeled by cosine and typical free-breathing model by 22% and 35%, respectively, and provided smooth tracking for radial direction. Motion tracking constancy as indicated by radial tracking discrepancy

Reference respiratory waveforms by minimum jerk model analysis

International Nuclear Information System (INIS)

Anetai, Yusuke; Sumida, Iori; Takahashi, Yutaka; Yagi, Masashi; Mizuno, Hirokazu; Ogawa, Kazuhiko; Ota, Seiichi

2015-01-01

Purpose: CyberKnife"® robotic surgery system has the ability to deliver radiation to a tumor subject to respiratory movements using Synchrony"® mode with less than 2 mm tracking accuracy. However, rapid and rough motion tracking causes mechanical tracking errors and puts mechanical stress on the robotic joint, leading to unexpected radiation delivery errors. During clinical treatment, patient respiratory motions are much more complicated, suggesting the need for patient-specific modeling of respiratory motion. The purpose of this study was to propose a novel method that provides a reference respiratory wave to enable smooth tracking for each patient. Methods: The minimum jerk model, which mathematically derives smoothness by means of jerk, or the third derivative of position and the derivative of acceleration with respect to time that is proportional to the time rate of force changed was introduced to model a patient-specific respiratory motion wave to provide smooth motion tracking using CyberKnife"®. To verify that patient-specific minimum jerk respiratory waves were being tracked smoothly by Synchrony"® mode, a tracking laser projection from CyberKnife"® was optically analyzed every 0.1 s using a webcam and a calibrated grid on a motion phantom whose motion was in accordance with three pattern waves (cosine, typical free-breathing, and minimum jerk theoretical wave models) for the clinically relevant superior–inferior directions from six volunteers assessed on the same node of the same isocentric plan. Results: Tracking discrepancy from the center of the grid to the beam projection was evaluated. The minimum jerk theoretical wave reduced the maximum-peak amplitude of radial tracking discrepancy compared with that of the waveforms modeled by cosine and typical free-breathing model by 22% and 35%, respectively, and provided smooth tracking for radial direction. Motion tracking constancy as indicated by radial tracking discrepancy affected by respiratory

Core stress distribution of phase shifting multimode polymer optical fiber

International Nuclear Information System (INIS)

Furukawa, Rei; Matsuura, Motoharu; Nagata, Morio; Mishima, Kenji; Inoue, Azusa; Tagaya, Akihiro; Koike, Yasuhiro

2013-01-01

Poly-(methyl methacrylate-co-benzyl methacrylate) polarization-maintaining optical fibers are known for their high response to normal stress. In this report, responses to higher stress levels up to 0.45 MPa were investigated. The stress amplitude and direction in the fiber cross section were calculated and analyzed with a coincident mode-field obtained from the near-field pattern. The stress amplitude varies significantly in the horizontal direction and is considered to create multiple phases, explaining the measurement results. To investigate possible permanent deformation, the core yield point profile was analyzed. Although it largely exceeds the average applied stress, the calculated stress distribution indicates that the core could partially experience stress that exceeds the yield point

Spatial variations of current tectonic stress field and its relationship to the structure and rheology of lithosphere around the Bohai Sea, North China

Science.gov (United States)

Li, Xianrui; Wang, Jie; Zeng, Zuoxun; Dai, Qingqin

2017-05-01

The tectonic stress field in the middle-upper crust is closely related to the structure and rheology of the lithosphere. To determine the stress field in the deep crust, we inversed the focal mechanism solutions (FMSs) of 62 earthquakes that occurred between 2009 and 2015 in the Bohai Sea and its surrounding areas using broadband seismic waveforms collected from 140 stations. We then derived the tectonic stress field using the software SATSI (Spatial And Temporal Stress Inversion) based on the damped linear inversion method. The inversion results show that both the maximum (σ1) and minimum (σ3) principle stress axes throughout the entire region are nearly horizontal except in the Tangshan and Haicheng areas, suggesting that the study area is predominantly under a strike-slip faulting stress regime. The σ1 and σ3 axes are found to be oriented in the NEE-SWW or nearly E-W and NNW-SSE or nearly S-N directions, respectively. These results indicate that the stress field in the North China Craton is controlled by the combined effects of the Pacific Plate westward subduction and the India-Eurasia Plate collision. However, localized normal faulting stress regimes (where the vertical stress σv ≈ σ1) are observed in the Tangshan and Haicheng areas, where low viscosity bodies (LVBs) were identified using geophysical data. Based on the analysis of focal mechanism solutions, active faults and lithosphere rheology characteristics in the Tangshan and Haicheng areas, we speculate that the anomalous stress regime is caused by the local extension resulting from the movement of strike-slip faults under the action of the regional stress field. The existence of LVB may indicate weakness in the crust that favors the accumulation of tectonic stress and triggers large earthquakes.

Vertical-horizontal wells for depletion and sweep

Energy Technology Data Exchange (ETDEWEB)

Muraikhi, A. J.; Pham, T. R.; Liu, J. S.; Khatib, M. R.; Muhaish, A. S. [Saudi Aramco (Saudi Arabia)

1998-12-31

A well completion scheme currently in use in a thick, large, elongated carbonate anticline Middle-East oil reservoir is described. This method of well completion calls for a combination of an open hole horizontal section penetrating the top 10 feet of the reservoir and a cased or undisturbed vertical segment through the thick formation. The horizontal section is used for producing and the vertical segment is used for monitoring purposes. Field experience and supported reservoir simulation exercises have shown that the horizontal application is superior to conventional vertical completion both from the economic and from the sweep point of view. 4 refs., 12 figs.

Horizontal bridges in polar dielectric liquids

Energy Technology Data Exchange (ETDEWEB)

Woisetschlaeger, Jakob [Graz University of Technology, Experimental Turbomachinery Research and Optical Measurement Group, Institute for Thermal Turbomachinery and Machine Dynamics, Graz (Austria); Wexler, Adam D.; Fuchs, Elmar C. [Wetsus, Center of Excellence for Sustainable Water Technology, Leeuwarden (Netherlands); Holler, Gert [Graz University of Technology, Institute of Electrical Measurement and Measurement Signal Processing, Graz (Austria); Eisenhut, Mathias [Graz University of Technology, Institute of Analytical Chemistry and Food Chemistry, Graz (Austria); Gatterer, Karl [Graz University of Technology, Institute of Physical and Theoretical Chemistry, Graz (Austria)

2012-01-15

When a high-voltage direct-current is applied to two beakers filled with polar liquid dielectrica like water or methanol, a horizontal bridge forms between the two beakers. By repeating a version of Pellat's experiment, it is shown that a horizontal bridge is stable by the action of electrohydrodynamic pressure. Thus, the static and dynamic properties of the phenomenon called a 'floating water bridge' can be explained by the gradient of Maxwell pressure, replenishing the liquid within the bridge against any drainage mechanism. It is also shown that a number of liquids can form stable and long horizontal bridges. The stability of such a connection, and the asymmetry in mass flow through such bridges caused by the formation of ion clouds in the vicinity of the electrodes, is also discussed by two further experiments. (orig.)

Bubble shape in horizontal and near horizontal intermittent flow

International Nuclear Information System (INIS)

Gu, Hanyang; Guo, Liejin

2015-01-01

Highlights: • The bubble shapes in intermittent flows are presented experimentally. • The nose-tail inversion phenomenon appears at a low Froude number in downward pipe. • Transition from plug to slug flow occurs when the bubble tail changes from staircase pattern to hydraulic jump. - Abstract: This paper presents an experimental study of the shape of isolated bubbles in horizontal and near horizontal intermittent flows. It is found that the shapes of the nose and body of bubble depend on the Froude number defined by gas/liquid mixture velocity in a pipe, whereas the shape of the back of bubble region depends on both the Froude number and bubble length. The photographic studies show that the transition from plug to slug flow occurs when the back of the bubble changes from staircase pattern to hydraulic jump with the increase of the Froude number and bubble length. The effect of pipe inclination on characteristics of bubble is significant: The bubble is inversely located in a downwardly inclined pipe when the Froude number is low, and the transition from plug flow to slug flow in an upward inclined pipe is more ready to occur compared with that in a downwardly inclined pipe

Widespread of horizontal gene transfer in the human genome.

Science.gov (United States)

Huang, Wenze; Tsai, Lillian; Li, Yulong; Hua, Nan; Sun, Chen; Wei, Chaochun

2017-04-04

A fundamental concept in biology is that heritable material is passed from parents to offspring, a process called vertical gene transfer. An alternative mechanism of gene acquisition is through horizontal gene transfer (HGT), which involves movement of genetic materials between different species. Horizontal gene transfer has been found prevalent in prokaryotes but very rare in eukaryote. In this paper, we investigate horizontal gene transfer in the human genome. From the pair-wise alignments between human genome and 53 vertebrate genomes, 1,467 human genome regions (2.6 M bases) from all chromosomes were found to be more conserved with non-mammals than with most mammals. These human genome regions involve 642 known genes, which are enriched with ion binding. Compared to known horizontal gene transfer regions in the human genome, there were few overlapping regions, which indicated horizontal gene transfer is more common than we expected in the human genome. Horizontal gene transfer impacts hundreds of human genes and this study provided insight into potential mechanisms of HGT in the human genome.

A comparative pressure analysis of air flow between horizontal and V-Tail of UAV MALE of NACA0012H with speed variation

Directory of Open Access Journals (Sweden)

Riza Rahmat

2018-01-01

Full Text Available NACA0012H is an airfoil type that could be used for Unmanned Aerial Vehicle Medium Altitude Long Endurance. This experiment was used to analyze stress in the surface of Tail of UAV MALE that was caused by air flow. The experiment was conducted using Computational Fluid Dynamics Software. Two designs of tail, horizontal and V-tail, were considered to simulate pressure occurred on the surface of leading edge, chamber and trailing edge. The simulation was developed varying the speed of the UAV MALE. The results showed that pressure occurred on the surface of horizontal tail higher than pressure on the V-tail.

Designing from minimum to optimum functionality

Science.gov (United States)

Bannova, Olga; Bell, Larry

2011-04-01

This paper discusses a multifaceted strategy to link NASA Minimal Functionality Habitable Element (MFHE) requirements to a compatible growth plan; leading forward to evolutionary, deployable habitats including outpost development stages. The discussion begins by reviewing fundamental geometric features inherent in small scale, vertical and horizontal, pressurized module configuration options to characterize applicability to meet stringent MFHE constraints. A proposed scenario to incorporate a vertical core MFHE concept into an expanded architecture to provide continuity of structural form and a logical path from "minimum" to "optimum" design of a habitable module. The paper describes how habitation and logistics accommodations could be pre-integrated into a common Hab/Log Module that serves both habitation and logistics functions. This is offered as a means to reduce unnecessary redundant development costs and to avoid EVA-intensive on-site adaptation and retrofitting requirements for augmented crew capacity. An evolutionary version of the hard shell Hab/Log design would have an expandable middle section to afford larger living and working accommodations. In conclusion, the paper illustrates that a number of cargo missions referenced for NASA's 4.0.0 Lunar Campaign Scenario could be eliminated altogether to expedite progress and reduce budgets. The plan concludes with a vertical growth geometry that provides versatile and efficient site development opportunities using a combination of hard Hab/Log modules and a hybrid expandable "CLAM" (Crew Lunar Accommodations Module) element.

Employment effects of minimum wages

OpenAIRE

Neumark, David

2014-01-01

The potential benefits of higher minimum wages come from the higher wages for affected workers, some of whom are in low-income families. The potential downside is that a higher minimum wage may discourage employers from using the low-wage, low-skill workers that minimum wages are intended to help. Research findings are not unanimous, but evidence from many countries suggests that minimum wages reduce the jobs available to low-skill workers.

L'intérêt du forage horizontal pour l'exploitation de gisements d'hydrocarbures Advantages of Horizontal Drilling for Production from Hydrocarbon Fields

Directory of Open Access Journals (Sweden)

Giger F.

2006-11-01

fields with very heterogeneous permeability, such as karstic reservoirs, a horizontal well has a very good chance of encountering highly productive zones (case of Rospo Mare in Italy where a productivity increase of 10 and more was found in comparison with neighboring vertical wells. A study of overall productivity on the scale of the field confirms that, if vertical wells are to be replaced by horizontal wells, their number may be divided by a factor of about 4 to obtain the sa:e production under equivalent conditions. To prevent water (or gas influxes during multiphase flow, a horizontal well has two advantages. It can be drilled near the top of the reservoir so as to obtain as much clearance as possible. Likewise, even with greater total production, production per unit length is less, thus locally causing more moderate stress on the oil/water or oil/gas interface. The shape of this interface is thus smoother, and calculations show that vertical sweep is more efficient, and hence recovery is greater. Generally speaking, in multiphase flow, horizontal wells reveal all the more superiority as the mobility ratio is unfavorable, e. g. heavy oil driven by water. The phenomenon to be prevented is indeed the breakthrough of fronts, which occurs all the sonner as flow is more unstable. The steadiness of drainage among horizontal wells provides more homogeneous progression to fronts, which is especially advantageous at the beginning of production. Nonetheless, since reservoirs are more or less heterogeneous, full benefit can be drawn from such favorable effects only if selective completions can be implemented in horizontal wells. For partly similar reasons, horizontal wells are advantageous for thermal recovery. The exact positioning of a perforated injection casing at a specific depth in a reservoir should enable steam to be fed in easily so that the zone it invades expands steadily, while decreasing heat losses into the surrounding formations. Lastly, it should be added that

On a Minimum Problem in Smectic Elastomers

International Nuclear Information System (INIS)

Buonsanti, Michele; Giovine, Pasquale

2008-01-01

Smectic elastomers are layered materials exhibiting a solid-like elastic response along the layer normal and a rubbery one in the plane. Balance equations for smectic elastomers are derived from the general theory of continua with constrained microstructure. In this work we investigate a very simple minimum problem based on multi-well potentials where the microstructure is taken into account. The set of polymeric strains minimizing the elastic energy contains a one-parameter family of simple strain associated with a micro-variation of the degree of freedom. We develop the energy functional through two terms, the first one nematic and the second one considering the tilting phenomenon; after, by developing in the rubber elasticity framework, we minimize over the tilt rotation angle and extract the engineering stress

Horizontal biases in rats’ use of three-dimensional space

Science.gov (United States)

Jovalekic, Aleksandar; Hayman, Robin; Becares, Natalia; Reid, Harry; Thomas, George; Wilson, Jonathan; Jeffery, Kate

2011-01-01

Rodent spatial cognition studies allow links to be made between neural and behavioural phenomena, and much is now known about the encoding and use of horizontal space. However, the real world is three dimensional, providing cognitive challenges that have yet to be explored. Motivated by neural findings suggesting weaker encoding of vertical than horizontal space, we examined whether rats show a similar behavioural anisotropy when distributing their time freely between vertical and horizontal movements. We found that in two- or three-dimensional environments with a vertical dimension, rats showed a prioritization of horizontal over vertical movements in both foraging and detour tasks. In the foraging tasks, the animals executed more horizontal than vertical movements and adopted a “layer strategy” in which food was collected from one horizontal level before moving to the next. In the detour tasks, rats preferred the routes that allowed them to execute the horizontal leg first. We suggest three possible reasons for this behavioural bias. First, as suggested by Grobety and Schenk [5], it allows minimisation of energy expenditure, inasmuch as costly vertical movements are minimised. Second, it may be a manifestation of the temporal discounting of effort, in which animals value delayed effort as less costly than immediate effort. Finally, it may be that at the neural level rats encode the vertical dimension less precisely, and thus prefer to bias their movements in the more accurately encoded horizontal dimension. We suggest that all three factors are related, and all play a part. PMID:21419172

Problems in the development of high-rank CBM horizontal wells in the Fanzhuang–Zhengzhuang Block in the Qinshui Basin and countermeasures

Directory of Open Access Journals (Sweden)

Yongping Zhang

2017-11-01

Full Text Available Coal reservoirs in the Qinshui Basin are characterized by high thermal evolution degree, low permeability, low reservoir pressure, lower gas saturation and strong heterogeneity, so its coalbed methane (CBM development is quite difficult. In this paper, the development practice of high-rank CBM horizontal wells in the Fanzhuang–Zhengzhuang Block was analyzed in terms of geological and engineering factors to clarify the productivity influencing factors, suitable geological conditions and potential tapping countermeasures of multi-lateral horizontal wells. It is shown that the reasons for the low development efficiency of multi-lateral horizontal wells are divided into three types. The first one is geological factor, such as encountering low CBM content areas or faults. The second is engineering factor, such as drilling fluid plugging, drilling collapse, drainage collapse and dust coal blockage. The third is the combination of both factors. It is concluded that encountering low CBM content areas and faults, collapse and blockage are the main reasons for the low production of multi-lateral horizontal wells in the Zhengzhuang–Fanzhuang Block, with the CBM content higher than 20 m3/t, the ratio of critical desorption pressure and reservoir pressure higher than 0.7 and vitrinite reflectance (Ro higher than 3.8. The prerequisite for an open-hole horizontal well in this area to produce CBM at a high rate is that the well lies in the tensile stress zone. Finally, the countermeasures to tap the potential of some inefficient wells were put forward. First, the inefficient wells which are blocked with dust coal or collapsed in the later stage should be stimulated based on classifications. And second, it is necessary to explore new types of horizontal wells so as to deal with borehole collapse and continue the operation in the later stage by using tree-like roof horizontal wells, single-lateral horizontal wells with casing or screen completion and fish

Characteristics of Buoyancy Driven Natural Ventilation through Horizontal Openings

DEFF Research Database (Denmark)

Li, Zhigang

through horizontal openings. Two cases of full-scale measurements of buoyancy driven natural ventilation through horizontal openings are performed: one horizontal opening and one horizontal opening combined with one vertical opening. For the case of one horizontal opening, the measurements are made....... Computational fluid dynamics (CFD) are used to study these two air flow cases. The air flow rate and air flow pattern are predicted and compared with the full-scale measurements. The measurement data are used to compare two CFD models: standard k- ε model and large eddy simulation (LES) model. The cases...... transient, unstable and complex, and the air flow rates oscillate with time. Correlations between the Froude number Fr and the opening ratio L/D are obtained, which is reasonable agreement with Epstein's formula derived from brine-water measurements, but the obtained Fr values show considerable deviations...

Characteristic Value Method of Well Test Analysis for Horizontal Gas Well

Directory of Open Access Journals (Sweden)

Xiao-Ping Li

2014-01-01

Full Text Available This paper presents a study of characteristic value method of well test analysis for horizontal gas well. Owing to the complicated seepage flow mechanism in horizontal gas well and the difficulty in the analysis of transient pressure test data, this paper establishes the mathematical models of well test analysis for horizontal gas well with different inner and outer boundary conditions. On the basis of obtaining the solutions of the mathematical models, several type curves are plotted with Stehfest inversion algorithm. For gas reservoir with closed outer boundary in vertical direction and infinite outer boundary in horizontal direction, while considering the effect of wellbore storage and skin effect, the pseudopressure behavior of the horizontal gas well can manifest four characteristic periods: pure wellbore storage period, early vertical radial flow period, early linear flow period, and late horizontal pseudoradial flow period. For gas reservoir with closed outer boundary both in vertical and horizontal directions, the pseudopressure behavior of the horizontal gas well adds the pseudosteady state flow period which appears after the boundary response. For gas reservoir with closed outer boundary in vertical direction and constant pressure outer boundary in horizontal direction, the pseudopressure behavior of the horizontal gas well adds the steady state flow period which appears after the boundary response. According to the characteristic lines which are manifested by pseudopressure derivative curve of each flow period, formulas are developed to obtain horizontal permeability, vertical permeability, skin factor, reservoir pressure, and pore volume of the gas reservoir, and thus the characteristic value method of well test analysis for horizontal gas well is established. Finally, the example study verifies that the new method is reliable. Characteristic value method of well test analysis for horizontal gas well makes the well test analysis

Horizontal and vertical seismic isolation of a nuclear power plant

International Nuclear Information System (INIS)

Ikonomou, A.S.

1983-01-01

This paper presents a study for the horizontal and vertical seismic isolation of a nuclear power plant with a base isolation system, developed by the author, called the Alexisismon. This system -- which comprises different schemes for horizontal or vertical or both horizontal and vertical isolation -- is a linear system based on the principle of separation of functions. That is, horizontal and vertical isolation are realized through different components and act independently from each other. As far as horizontal isolation is concerned, the role of transmitting vertical loads is uncoupled from the role of inducing horizontal restoring forces so that both functions can be performed without instability. It is possible either to provide both horizontal and vertical isolation to the whole nuclear plant or to isolate the whole plant horizontally and to provide vertical isolation to sensitive and costly equipment only. When the fundamental period of the plant or equipment is 2 seconds and when the vertical displacements are of the order of + or - 20 inches, the structure or equipment are protected against earthquakes up to 1.10 and 1.30 g for actual and 0.60 and 1.50 g for artificial accelerograms. In both cases all the isolation elements behave elastically up to these acceleration limits as well as the superstructure and equipment

Bolt Thread Stress Optimization

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2012-01-01

of threads and therefore indirectly the bolt fatigue life. The root shape is circular, and from shape optimization for minimum stress concentration it is well known that the circular shape is seldom optimal. An axisymmetric Finite Element (FE) formulation is used to analyze the bolted connection, and a study...... is performed to establish the need for contact modeling with regard to finding the correct stress concentration factor. Optimization is performed with a simple parameterization with two design variables. Stress reduction of up to 9% is found in the optimization process, and some similarities are found...... in the optimized designs leading to the proposal of a new standard. The reductions in the stress are achieved by rather simple changes made to the cutting tool....

Estimating minimum polycrystalline aggregate size for macroscopic material homogeneity

International Nuclear Information System (INIS)

Kovac, M.; Simonovski, I.; Cizelj, L.

2002-01-01

During severe accidents the pressure boundary of reactor coolant system can be subjected to extreme loadings, which might cause failure. Reliable estimation of the extreme deformations can be crucial to determine the consequences of severe accidents. Important drawback of classical continuum mechanics is idealization of inhomogenous microstructure of materials. Classical continuum mechanics therefore cannot predict accurately the differences between measured responses of specimens, which are different in size but geometrical similar (size effect). A numerical approach, which models elastic-plastic behavior on mesoscopic level, is proposed to estimate minimum size of polycrystalline aggregate above which it can be considered macroscopically homogeneous. The main idea is to divide continuum into a set of sub-continua. Analysis of macroscopic element is divided into modeling the random grain structure (using Voronoi tessellation and random orientation of crystal lattice) and calculation of strain/stress field. Finite element method is used to obtain numerical solutions of strain and stress fields. The analysis is limited to 2D models.(author)

Topological properties of the limited penetrable horizontal visibility graph family

Science.gov (United States)

Wang, Minggang; Vilela, André L. M.; Du, Ruijin; Zhao, Longfeng; Dong, Gaogao; Tian, Lixin; Stanley, H. Eugene

2018-05-01

The limited penetrable horizontal visibility graph algorithm was recently introduced to map time series in complex networks. In this work, we extend this algorithm to create a directed-limited penetrable horizontal visibility graph and an image-limited penetrable horizontal visibility graph. We define two algorithms and provide theoretical results on the topological properties of these graphs associated with different types of real-value series. We perform several numerical simulations to check the accuracy of our theoretical results. Finally, we present an application of the directed-limited penetrable horizontal visibility graph to measure real-value time series irreversibility and an application of the image-limited penetrable horizontal visibility graph that discriminates noise from chaos. We also propose a method to measure the systematic risk using the image-limited penetrable horizontal visibility graph, and the empirical results show the effectiveness of our proposed algorithms.

Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of an approach to modelling the state of stress

Energy Technology Data Exchange (ETDEWEB)

Hakami, Eva; Hakami, Hossein [Itasca Geomekanik AB, Solna (Sweden); Cosgrove, John [Imperial College of Science and Technology, London (United Kingdom)

2002-05-01

performed using overcoring techniques or overcoring supported by hydraulic fracturing and HTPF measurements. Overcoring measurement techniques can be used to determine magnitude and orientation of all three principal stresses. Hydraulic fracturing measurements can be used to determine the magnitude and orientation of the minimum horizontal stress, often coinciding with the minimum principal stress. The maximum principal stresses can be estimated by multiplying the ration between the maximum and minimum principal stress, from overcoring, with the minimum principal stress determined by hydraulic fracturing. Hydraulic fracturing can be performed in existing boreholes. Boreholes for stress measurements are recommended to be located in all rock units, within which a reliable prediction is desired.

Strategy for a Rock Mechanics Site Descriptive Model. Development and testing of an approach to modelling the state of stress

International Nuclear Information System (INIS)

Hakami, Eva; Hakami, Hossein; Cosgrove, John

2002-05-01

techniques or overcoring supported by hydraulic fracturing and HTPF measurements. Overcoring measurement techniques can be used to determine magnitude and orientation of all three principal stresses. Hydraulic fracturing measurements can be used to determine the magnitude and orientation of the minimum horizontal stress, often coinciding with the minimum principal stress. The maximum principal stresses can be estimated by multiplying the ration between the maximum and minimum principal stress, from overcoring, with the minimum principal stress determined by hydraulic fracturing. Hydraulic fracturing can be performed in existing boreholes. Boreholes for stress measurements are recommended to be located in all rock units, within which a reliable prediction is desired

Behavioral and physiological significance of minimum resting metabolic rate in king penguins.

Science.gov (United States)

Halsey, L G; Butler, P J; Fahlman, A; Woakes, A J; Handrich, Y

2008-01-01

Because fasting king penguins (Aptenodytes patagonicus) need to conserve energy, it is possible that they exhibit particularly low metabolic rates during periods of rest. We investigated the behavioral and physiological aspects of periods of minimum metabolic rate in king penguins under different circumstances. Heart rate (f(H)) measurements were recorded to estimate rate of oxygen consumption during periods of rest. Furthermore, apparent respiratory sinus arrhythmia (RSA) was calculated from the f(H) data to determine probable breathing frequency in resting penguins. The most pertinent results were that minimum f(H) achieved (over 5 min) was higher during respirometry experiments in air than during periods ashore in the field; that minimum f(H) during respirometry experiments on water was similar to that while at sea; and that RSA was apparent in many of the f(H) traces during periods of minimum f(H) and provides accurate estimates of breathing rates of king penguins resting in specific situations in the field. Inferences made from the results include that king penguins do not have the capacity to reduce their metabolism to a particularly low level on land; that they can, however, achieve surprisingly low metabolic rates at sea while resting in cold water; and that during respirometry experiments king penguins are stressed to some degree, exhibiting an elevated metabolism even when resting.

Minimum Wages and Poverty

OpenAIRE

Fields, Gary S.; Kanbur, Ravi

2005-01-01

Textbook analysis tells us that in a competitive labor market, the introduction of a minimum wage above the competitive equilibrium wage will cause unemployment. This paper makes two contributions to the basic theory of the minimum wage. First, we analyze the effects of a higher minimum wage in terms of poverty rather than in terms of unemployment. Second, we extend the standard textbook model to allow for incomesharing between the employed and the unemployed. We find that there are situation...

Vertical vs. Horizontal Integration: Pre-emptive Merging.

OpenAIRE

Colangelo, Giuseppe

1995-01-01

Preemption plays a crucial role in arms merger decisions. The author studies whether and under which circumstances preemptive merging occurs in vertically related industries. He finds that vertical mergers often preempt horizontal mergers and are dominant outcomes. Preempting the threat of a detrimental horizontal integration may be the main reason for vertically integrating. Copyright 1995 by Blackwell Publishing Ltd.

Topography, stresses, and stability at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Swolfs, H.S.; Savage, W.Z.

1985-01-01

Plane-strain solutions are used to analyze the influence of topography on the state of stress at Yucca Mountain, Nye County, Nevada. The results are in good agreement with the measured stress components obtained in drill holes by the hydraulic-fracturing technique, particularly those measured directly beneath the crest of the ridge, and indicate that these stresses are gravitationally induced. A separate analysis takes advantage of the fact that a well-developed set of vertical faults and fractures, subparallel to the ridge trend, imparts a vertical transverse isotropy to the rock and that, as a consequence of gravitational loading, unequal horizontal stresses are induced in directions perpendicular and parallel to the anisotropy

Finite element prediction on the chassis design of UniART4 racing car

Science.gov (United States)

Zaman, Z. I.; Basaruddin, K. S.; Basha, M. H.; Rahman, M. T. Abd; Daud, R.

2017-09-01

This paper presents the analysis and evaluation of the chassis design for University Automotive Racing Team No. 4 (UniART4) car based on finite element analysis. The existing UniART4 car chassis was measured and modelled geometrically using Solidwork before analysed in FEA software (ANSYS). Four types of static structural analysis were used to predict the chassis design capability under four different loading conditions; vertical bending, lateral bending, lateral torsion and horizontal lozenging. The results showed the chassis subjected to the highest stress and strain under horizontal lozenging, whereas the minimum stress and strain response was obtained under lateral bending. The present analysis result could provide valuable information in predicting the sustainability of the current UniART car chassis design.

75 FR 6151 - Minimum Capital

Science.gov (United States)

2010-02-08

... capital and reserve requirements to be issued by order or regulation with respect to a product or activity... minimum capital requirements. Section 1362(a) establishes a minimum capital level for the Enterprises... entities required under this section.\\6\\ \\3\\ The Bank Act's current minimum capital requirements apply to...

A Pareto-Improving Minimum Wage

OpenAIRE

Eliav Danziger; Leif Danziger

2014-01-01

This paper shows that a graduated minimum wage, in contrast to a constant minimum wage, can provide a strict Pareto improvement over what can be achieved with an optimal income tax. The reason is that a graduated minimum wage requires high-productivity workers to work more to earn the same income as low-productivity workers, which makes it more difficult for the former to mimic the latter. In effect, a graduated minimum wage allows the low-productivity workers to benefit from second-degree pr...

Historical volcanism and the state of stress in the East African Rift System

Directory of Open Access Journals (Sweden)

Geoffrey Wadge

2016-09-01

Full Text Available Crustal extension at the East African Rift System (EARS should, as a tectonic ideal, involve a stress field in which the direction of minimum horizontal stress is perpendicular to the rift. A volcano in such a setting should produce dykes and fissures parallel to the rift. How closely do the volcanoes of the EARS follow this? We answer this question by studying the 21 volcanoes that have erupted historically (since about 1800 and find that 7 match the (approximate geometrical ideal. At the other 14 volcanoes the orientation of the eruptive fissures/dykes and/or the axes of the host rift segments are oblique to the ideal values. To explain the eruptions at these volcanoes we invoke local (non-plate tectonic variations of the stress field caused by: crustal heterogeneities and anisotropies (dominated by NW structures in the Protoerozoic basement, transfer zone tectonics at the ends of offset rift segments, gravitational loading by the volcanic edifice (typically those with 1-2 km relief and magmatic pressure in central reservoirs. We find that the more oblique volcanoes tend to have large edifices, large eruptive volumes and evolved and mixed magmas capable of explosive behaviour. Nine of the volcanoes have calderas of varying ellipticity, 6 of which are large, reservoir-collapse types mainly elongated across rift (e.g. Kone and 3 are smaller, elongated parallel to the rift and contain active lava lakes (e.g. Erta Ale, suggesting different mechanisms of formation and stress fields. Nyamuragira is the only EARS volcano with enough sufficiently well-documented eruptions to infer its long-term dynamic behaviour. Eruptions within 7 km of the volcano are of relatively short duration (<100 days, but eruptions with more distal fissures tend to have greater obliquity and longer durations, indicating a changing stress field away from the volcano. There were major changes in long-term magma extrusion rates in 1977 (and perhaps in 2002 due to major along

GABA sensitivity of spectrally classified horizontal cells in goldfish retina

NARCIS (Netherlands)

Verweij, J.; Kamermans, M.; Negishi, K.; Spekreijse, H.

1998-01-01

We studied the GABA sensitivity of horizontal cells in the isolated goldfish retina. After the glutamatergic input to the horizontal cells was blocked with DNQX, GABA depolarized the monophasic and biphasic horizontal cells. The pharmacology of these GABA-induced depolarizations was tested with the

Minimum critical mass systems

International Nuclear Information System (INIS)

Dam, H. van; Leege, P.F.A. de

1987-01-01

An analysis is presented of thermal systems with minimum critical mass, based on the use of materials with optimum neutron moderating and reflecting properties. The optimum fissile material distributions in the systems are obtained by calculations with standard computer codes, extended with a routine for flat fuel importance search. It is shown that in the minimum critical mass configuration a considerable part of the fuel is positioned in the reflector region. For 239 Pu a minimum critical mass of 87 g is found, which is the lowest value reported hitherto. (author)

Stresses in a submarine topography under ocean waves

Energy Technology Data Exchange (ETDEWEB)

Mei, C.C.; McTigue, D.F.

1984-09-01

The problem of submarine slope stability is of interest to both offshore engineering and geology. In an uneven topography, the weight above a horizontal plane induces two-dimensional variation in the static stress field. The action of wave pressure, which changes with depth, further introduces excess pore pressure and dynamic stresses in the sea bottom. In the present paper, we combine a simple analytical theory for the static stress by the present authors, and the recent solution by Mei and Foda for wave-induced stresses in a plane poro-elastic sea bed to account for mild bottom slope and wave shoaling, and obtain the effective stress field in a submarine topography under sea waves. Sample results are given for a ridge and a canyon. In particular, the dynamic pore pressure and the combined static and dynamic effective stresses are presented.

Life time forecasting method upon occurrence of stress corrosion cracking of structure and test device therefor

International Nuclear Information System (INIS)

Anzai, Hideya; Kida, Toshitaka; Urayama, Yoshinao; Kikuchi, Eiji; Shimanuki, Sei; Kuniya, Jiro; Nakata, Kiyotomo; Izumitani, Masakiyo; Hattori, Shigeo.

1993-01-01

A load stress is applied to a metal piece made of a material identical with the constituent material of a structure and having the sensitivity enhanced to a predetermined level, and plurality of such pieces are immersed in a corrosive circumstance in this state. Then, the time from the immersion till the rupture thereof and the number of ruptured pieces of the metal pieces are detected while observing them. The relation with the probability of rupture is plotted on a paper to determine the life time for the occurrence of minimum stress corrosion creacks (SSC) of the metal pieces. Based on the relationship between the previously determined stress and the life time for the occurrence of minimum SSC, the ratio between the life time for the occurrence of minimum SSC relative to estimated stress applied to the structure and the life time for the occurrence of minimum SSC relative to the stress applied to the metal pieces is determined as a first SSC acceleration rate. The ratio between the time of occurrence for minimum SSC and the sensitivity is determined as a second SSC acceleration rate. The first and the second SSC acceleration rates are multiplied to estimate the time for the occurrence of SSC of the structure. Then, the life time for the occurrence of SSC for the equipments and structures can be recognized quantitatively, to prevent ruptures of actual equipments and extend the life time. (N.H.)

Electroluminescence from completely horizontally oriented dye molecules

Energy Technology Data Exchange (ETDEWEB)

Komino, Takeshi [Education Center for Global Leaders in Molecular System for Devices, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Center for Organic Photonics and Electronics Research, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Japan Science and Technology Agency, ERATO, Adachi Molecular Exciton Engineering Project, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Sagara, Yuta [Center for Organic Photonics and Electronics Research, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Tanaka, Hiroyuki [Center for Organic Photonics and Electronics Research, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Department of Chemistry, Graduate School of Science, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8601 (Japan); Oki, Yuji [Japan Science and Technology Agency, ERATO, Adachi Molecular Exciton Engineering Project, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Department of Electronics, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Nakamura, Nozomi [Center for Organic Photonics and Electronics Research, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); International Institute for Carbon Neutral Energy Research (WPI-I2CNER), Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Fujimoto, Hiroshi [Center for Organic Photonics and Electronics Research, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan); Fukuoka i" 3-Center for Organic Photonics and Electronics Research (i3-OPERA), Fukuoka 819-0388 (Japan); and others

2016-06-13

A complete horizontal molecular orientation of a linear-shaped thermally activated delayed fluorescent guest emitter 2,6-bis(4-(10Hphenoxazin-10-yl)phenyl)benzo[1,2-d:5,4-d′] bis(oxazole) (cis-BOX2) was obtained in a glassy host matrix by vapor deposition. The orientational order of cis-BOX2 depended on the combination of deposition temperature and the type of host matrix. Complete horizontal orientation was obtained when a thin film with cis-BOX2 doped in a 4,4′-bis(N-carbazolyl)-1,1′-biphenyl (CBP) host matrix was fabricated at 200 K. The ultimate orientation of guest molecules originates from not only the kinetic relaxation but also the kinetic stability of the deposited guest molecules on the film surface during film growth. Utilizing the ultimate orientation, a highly efficient organic light-emitting diode with the external quantum efficiency of 33.4 ± 2.0% was realized. The thermal stability of the horizontal orientation of cis-BOX2 was governed by the glass transition temperature (T{sub g}) of the CBP host matrix; the horizontal orientation was stable unless the film was annealed above T{sub g}.

Implications of Liebig’s law of the minimum for tree-ring reconstructions of climate

Science.gov (United States)

Stine, A. R.; Huybers, P.

2017-11-01

A basic principle of ecology, known as Liebig’s Law of the Minimum, is that plant growth reflects the strongest limiting environmental factor. This principle implies that a limiting environmental factor can be inferred from historical growth and, in dendrochronology, such reconstruction is generally achieved by averaging collections of standardized tree-ring records. Averaging is optimal if growth reflects a single limiting factor and noise but not if growth also reflects locally variable stresses that intermittently limit growth. In this study a collection of Arctic tree ring records is shown to follow scaling relationships that are inconsistent with the signal-plus-noise model of tree growth but consistent with Liebig’s Law acting at the local level. Also consistent with law-of-the-minimum behavior is that reconstructions based on the least-stressed trees in a given year better-follow variations in temperature than typical approaches where all tree-ring records are averaged. Improvements in reconstruction skill occur across all frequencies, with the greatest increase at the lowest frequencies. More comprehensive statistical-ecological models of tree growth may offer further improvement in reconstruction skill.

Effective Stress Law in Unconventional Reservoirs under Different Boundary Conditions

Science.gov (United States)

Saurabh, S.; Harpalani, S.

2017-12-01

Unconventional reservoirs have attracted a great deal of research interest worldwide during the past two decades. Low permeability and specialized techniques required to exploit these resources present opportunities for improvement in both production rates and ultimate recovery. Understanding subsurface stress modifications and permeability evolution are valuable when evaluating the prospects of unconventional reservoirs. These reservoir properties are functions of effective stress. As a part of this study, effective stress law, specifically the variation of anisotropic Biot's coefficient under various boundary conditions believed to exist in gas reservoirs by different researchers, has been established. Pressure-dependent-permeability (PdK) experiments were carried out on San Juan coal under different boundary conditions, that is, uniaxial strain condition and constant volume condition. Stress and strain in the vertical and horizontal directions were monitored throughout the experiment. Data collected during the experiments was used to determine the Biot's coefficient in vertical and horizontal directions under these two boundary conditions, treating coal as transversely isotropic. The variation of Biot's coefficient was found to be well correlated with the variation in coal permeability. Based on the estimated values of Biot's coefficients, a theory of variation in its value is presented for other boundary conditions. The findings of the study shed light on the inherent behavior of Biot's coefficient under different reservoir boundary conditions. This knowledge can improve the modeling work requiring estimation of effective stress in reservoirs, such as, pressure-/stress- dependent permeability. At the same time, if the effective stresses are known with more certainty by other methods, it enables assessment of the unknown reservoir boundary conditions.

In situ stress measurements at 250m gallery off the ventilation shaft

International Nuclear Information System (INIS)

Nakamura, Takahiro; Sanada, Hiroyuki; Sugita, Yutaka; Kato, Harumi

2011-06-01

boreholes. Shut-in pressure of inclined transverse cracks and the circumferential position of longitudinal cracks on the wellbore surface were used to determine the magnitude and orientation of principal stress around the 250m gallery on the assumption that all of the target zones of hydraulic fracturing were in a uniform stress state. The determined in situ stress state showed a little difference of magnitude between intermediate stress and minimum stress. The vertical component of the in situ stress was evaluated to be about a half of the overburden at the test site. The maximum principal stress was inclined to about 40 degrees from the level with azimuth of NE orientation. The reason why the evaluated state of stress at 140m niches and 250m gallery are different would be attributed to geological environment. (2) Stress relief method by conical-ended borehole overcoring. Stress relief method by conical-ended borehole overcoring was successfully conducted at the depths of 17.25m and 17.72m of the borehole 09-V250-M02. Orientation of the evaluated principal stresses at the two depths showed a good agreement. The maximum principal stress inclined about 60 degrees from the level with azimuth of NNE and the intermediate principal stress was almost horizontal with WNW orientation. The orientation of the maximum principal stress was almost perpendicular to the plane of sedimentation of Koetoi formation and Wakkanai formation. The magnitude of the maximum principal stress was comparable to the uniaxial compressive strength of Wakkanai formation. The estimated ratio of the principal stresses σ 1 /σ 3 was 11.6 and 6.0 at the depth of 17.25m and 17.72m, respectively. No spalling of the walls of the boreholes due to the stress concentration was detected while both the magnitude and the ratio of principal stress were large enough to cause borehole breakout. The inconsistency would be explained by microcracks in the boring core formed during the drilling process or/and by elastic

5 CFR 551.301 - Minimum wage.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Minimum wage. 551.301 Section 551.301... FAIR LABOR STANDARDS ACT Minimum Wage Provisions Basic Provision § 551.301 Minimum wage. (a)(1) Except... employees wages at rates not less than the minimum wage specified in section 6(a)(1) of the Act for all...

Widespread of horizontal gene transfer in the human genome

OpenAIRE

Huang, Wenze; Tsai, Lillian; Li, Yulong; Hua, Nan; Sun, Chen; Wei, Chaochun

2017-01-01

Background A fundamental concept in biology is that heritable material is passed from parents to offspring, a process called vertical gene transfer. An alternative mechanism of gene acquisition is through horizontal gene transfer (HGT), which involves movement of genetic materials between different species. Horizontal gene transfer has been found prevalent in prokaryotes but very rare in eukaryote. In this paper, we investigate horizontal gene transfer in the human genome. Results From the pa...

Effect of the weld joint configuration on stressed components, residual stresses and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Cevik, Bekir; Oezer, Alpay; Oezcatalbas, Yusuf [Gazi Univ., Ankara (Turkey)

2014-03-01

The effect of the weld joint configuration on components has been studied, which are under service loads, under repair or construction and the residual stresses as well as the mechanical properties of the joint have been determined. For this purpose, a horizontal positioned tensile testing device and a semi-automatic MIG welding machine have been used and then the weld joints of the plates were subjected to different elastic stresses. When the temperature of the joined elements decreased to room temperature, applied elastic stresses were released. By this means, the effects of the existing tensile stresses in the joined parts and the tensile stresses created by the welding processes were investigated. The tensile stresses occurring in the joined elements were determined by using the photo-elasticity analysis method and the hole-drilling method. Also, tensile-shear tests were applied in order to determine the effect of permanent tensile loads on the mechanical properties of the joint. Experimental results showed that the application of corner welded lap joints for components under tensile loading significantly decrease the shear strength and yielding capacities of the joint. (orig.)

New horizontal global solar radiation estimation models for Turkey based on robust coplot supported genetic programming technique

International Nuclear Information System (INIS)

Demirhan, Haydar; Kayhan Atilgan, Yasemin

2015-01-01

Highlights: • Precise horizontal global solar radiation estimation models are proposed for Turkey. • Genetic programming technique is used to construct the models. • Robust coplot analysis is applied to reduce the impact of outlier observations. • Better estimation and prediction properties are observed for the models. - Abstract: Renewable energy sources have been attracting more and more attention of researchers due to the diminishing and harmful nature of fossil energy sources. Because of the importance of solar energy as a renewable energy source, an accurate determination of significant covariates and their relationships with the amount of global solar radiation reaching the Earth is a critical research problem. There are numerous meteorological and terrestrial covariates that can be used in the analysis of horizontal global solar radiation. Some of these covariates are highly correlated with each other. It is possible to find a large variety of linear or non-linear models to explain the amount of horizontal global solar radiation. However, models that explain the amount of global solar radiation with the smallest set of covariates should be obtained. In this study, use of the robust coplot technique to reduce the number of covariates before going forward with advanced modelling techniques is considered. After reducing the dimensionality of model space, yearly and monthly mean daily horizontal global solar radiation estimation models for Turkey are built by using the genetic programming technique. It is observed that application of robust coplot analysis is helpful for building precise models that explain the amount of global solar radiation with the minimum number of covariates without suffering from outlier observations and the multicollinearity problem. Consequently, over a dataset of Turkey, precise yearly and monthly mean daily global solar radiation estimation models are introduced using the model spaces obtained by robust coplot technique and

Resolution of thermal striping issue downstream of a horizontal pipe elbow in stratified pipe flow

International Nuclear Information System (INIS)

Kuzay, T.M.; Kasza, K.E.

1985-01-01

A thermally stratified pipe flow produced by a thermal transient when passing through a horizontal elbow as a result of secondary flow gives rise to large thermal fluctuations on the inner curvature wall of the downstream piping. These fluctuations were measured in a specially instrumented horizontal pipe and elbow system on a test set-up using water in the Mixing Components Technology Facility (MCTF) at Argonne National Laboratory (ANL). This study is part of a larger program which is studying the influence of thermal buoyancy on general reactor component performance. This paper discusses the influence of pipe flow generated thermal oscillations on the thermal stresses induced in the pipe walls. The instrumentation was concentrated around the exit plane of the 90 0 sweep elbow, since prior tests had indicated that the largest thermal fluctuations would occur within about one hydraulic diameter downstream of the elbow exit. The thermocouples were located along the inner curvature of the piping and measured the near surface fluid temperature. The test matrix involved thermal downramps under turbulent flow conditions

Towards the prediction of pre-mining stresses in the European continent. [Estimates of vertical and probable maximum lateral stress in Europe

Energy Technology Data Exchange (ETDEWEB)

Blackwood, R. L.

1980-05-15

There are now available sufficient data from in-situ, pre-mining stress measurements to allow a first attempt at predicting the maximum stress magnitudes likely to occur in a given mining context. The sub-horizontal (lateral) stress generally dominates the stress field, becoming critical to stope stability in many cases. For cut-and-fill mining in particular, where developed fill pressures are influenced by lateral displacement of pillars or stope backs, extraction maximization planning by mathematical modelling techniques demands the best available estimate of pre-mining stresses. While field measurements are still essential for this purpose, in the present paper it is suggested that the worst stress case can be predicted for preliminary design or feasibility study purposes. In the Eurpoean continent the vertical component of pre-mining stress may be estimated by adding 2 MPa to the pressure due to overburden weight. The maximum lateral stress likely to be encountered is about 57 MPa at depths of some 800m to 1000m below the surface.

Sidewall containment of liquid metal with horizontal alternating magnetic fields

Science.gov (United States)

Pareg, Walter F.

1990-01-01

An apparatus for confining molten metal with a horizontal alternating magnetic field. In particular, this invention employs a magnet that can produce a horizontal alternating magnetic field to confine a molten metal at the edges of parallel horizontal rollers as a solid metal sheet is cast by counter-rotation of the rollers.

Computation of principal stresses and stress intensity of a nozzle on a spherical pressure vessel

International Nuclear Information System (INIS)

Sun, B.C.; Lyow, B.L.; Koplik, B.

1993-01-01

This paper presents a Stress Computation Table that systematically computes the local stresses at various locations of the sphere-nozzle intersection. The six components of external loading are: radial load, two overturning moments, two horizontal shear forces, and a torsional moment. The radial and overturning moments induce local membrane and bending stresses in both the circumferential and meridional directions of the sphere around the nozzle. The shear forces and torsional moment produce local shear stresses. In addition, the shear forces induce local membrane and bending stresses around the nozzle. The local stress factors from each external loading component are taken from recent publications by Lyow, Sun and Koplik who have studied this subject through the use of the finite element method. These factors are a function of the nozzle-sphere geometrical parameters, beta, β, (nozzle radius/sphere radius) and gamma, γ, (sphere radius/thickness), with the beta value ranging from 0.1 to 0.5, and the gamma value ranging from 10 to 100. The Stress Table summarizes all the normal and shear stresses at eight different locations around the nozzle, and finally the principal stresses and stress intensity are computed. The stress factor plots from previous publications are replotted in this paper to provide a handy reference as well as consistency. A numerical sample employing a FORTRAN program is also given. (author)

A horizontal well analysis from a view of its productivity

Directory of Open Access Journals (Sweden)

Lucia Sciranková

2006-10-01

Full Text Available The 1990s may become known in the oil field as the decade of the horizontal well. Horizontal wells can increase the production rate and the ultimate recovery, and can reduce the number of platforms on wells required to develop a reservoir.An empirical equation to calculate the inflow performance of two-phase flow for a vertical and a horizontal well in regime of dissolved gas presented by Vogel in 1968. His equation was based on the results of reservoir simulation. The created model whore result (output is the ratio of the productivity of a horizontal well to the productivity of a vertical well for a given area expressed by anumber of vertical wells the replaced by one horizontal well. The model is applied for a concrete ideological model.

Horizontal and Vertical Rule Bases Method in Fuzzy Controllers

OpenAIRE

Aminifar, Sadegh; bin Marzuki, Arjuna

2013-01-01

Concept of horizontal and vertical rule bases is introduced. Using this method enables the designers to look for main behaviors of system and describes them with greater approximations. The rules which describe the system in first stage are called horizontal rule base. In the second stage, the designer modulates the obtained surface by describing needed changes on first surface for handling real behaviors of system. The rules used in the second stage are called vertical rule base. Horizontal...

Condensation Analysis of Steam/Air Mixtures in Horizontal Tubes

International Nuclear Information System (INIS)

Lee, Kwon Yeong; Bae, Sung Won; Kim, Moo Hwan

2008-01-01

Perhaps the most common flow configuration in which a convective condensation occurs is a flow in a horizontal circular tube. This configuration is encountered in air-conditioning and refrigeration condensers as well as condensers in Rankine power cycles. Although a convective condensation is also sometimes contrived to occur in a co-current vertical downward flow, a horizontal flow is often preferred because the flow can be repeatedly passed through the heat exchanger core in a serpentine fashion without trapping liquid or vapor in the return bends. Many researchers have investigated a in-tube condensation for horizontal heat exchangers. However, almost all of them obtained tube section-averaged data without a noncondensable gas. Recently, Wu and Vierow have experimentally studied the condensation of steam in a horizontal heat exchanger with air present. In order to measure the condenser tube inner surface temperatures and to calculate the local heat fluxes, they developed an innovative thermocouple design that allowed for nonintrusive measurements. Here we developed a theoretical model using the heat and mass analogy to analyze a steam condensation with a noncondensable gas in horizontal tubes

Rock stresses (Grimsel rock laboratory)

International Nuclear Information System (INIS)

Pahl, A.; Heusermann, S.; Braeuer, V.; Gloeggler, W.

1989-01-01

On the research and development project 'Rock Stress Measurements' the BGR has developed and tested several test devices and methods at GTS for use in boreholes at a depth of 200 m and has carried out rock mechanical and engineering geological investigations for the evaluation and interpretation of the stress measurements. The first time a computer for data processing was installed in the borehole together with the BGR-probe. Laboratory tests on hollow cylinders were made to study the stress-deformation behavior. To validate and to interprete the measurement results some test methods were modelled using the finite-element method. The dilatometer-tests yielded high values of Young's modulus, whereas laboratory tests showed lower values with a distinct deformation anisotropy. Stress measurements with the BGR-probe yielded horizontal stresses being higher than the theoretical overburden pressure and vertical stresses which agree well with the theoretical overburden pressure. These results are comparable to the results of the hydraulic fracturing tests, whereas stresses obtained with CSIR-triaxial cells are generally lower. The detailed geological mapping of the borehole indicated relationships between stress and geology. With regard to borehole depth different zones of rock structure joint frequency, joint orientation, and orientation of microfissures as well as stress magnitude, stress direction, and degree of deformation anisotropy could be distinguished. (orig./HP) [de

The influence of applied tensile stress on power loss in Co-rich amorphous Co-Fe-Si-B ribbons with induced magnetic anisotropy

DEFF Research Database (Denmark)

Nielsen, H; Nielsen, K; Nielsen, Otto V

1982-01-01

and atf = 400Hz,J_{max} = 0.10T. Measurements are carried out on samples in a stress-relieved state and with magnetic anisotropies induced by stress or field annealing. Atf = 50Hz, a minimum m Ptversus σ is observed. The σ-value (sigma_{min}) corresponding to the minimum PTincreases with increasing |Ku......|. Atf = 400Hz, a minimum in PTversus σ is observed in the samples with induced magnetic anisotropy, whereassigma_{min} = 0in the stress-relieved samiales. However, no correlation between andsigma_{min}and Kuis possible from the present data....

Influence of pavement condition on horizontal curve safety.

Science.gov (United States)

Buddhavarapu, Prasad; Banerjee, Ambarish; Prozzi, Jorge A

2013-03-01

Crash statistics suggest that horizontal curves are the most vulnerable sites for crash occurrence. These crashes are often severe and many involve at least some level of injury due to the nature of the collisions. Ensuring the desired pavement surface condition is one potentially effective strategy to reduce the occurrence of severe accidents on horizontal curves. This study sought to develop crash injury severity models by integrating crash and pavement surface condition databases. It focuses on developing a causal relationship between pavement condition indices and severity level of crashes occurring on two-lane horizontal curves in Texas. In addition, it examines the suitability of the existing Skid Index for safety maintenance of two-lane curves. Significant correlation is evident between pavement condition and crash injury severity on two-lane undivided horizontal curves in Texas. Probability of a crash becoming fatal is appreciably sensitive to certain pavement indices. Data suggested that road facilities providing a smoother and more comfortable ride are vulnerable to severe crashes on horizontal curves. In addition, the study found that longitudinal skid measurement barely correlates with injury severity of crashes occurring on curved portions. The study recommends exploring the option of incorporating lateral friction measurement into Pavement Management System (PMS) databases specifically at curved road segments. Copyright © 2012 Elsevier Ltd. All rights reserved.

Stresses in a submarine topography under ocean waves

Energy Technology Data Exchange (ETDEWEB)

Mei, C.C.; McTigue, D.F.

1984-01-01

The problem of submarine slope stability is of interest to both offshore engineering and geology. In an uneven topography, the weight above a horizontal plane induces two-dimensional variation in the static stress field. The action of wave pressure, which changes with depth, further introduces excess pore pressure and dynamic stresses in the sea bottom. In the present paper, we combine a simple analytical theory for the static stress by the present authors, and the recent solution by Mei and Foda for wave-induced stresses in a plane poro-elastic sea bed to account for mild bottom slope and wave shoaling, to obtain the effective stress field in a submarine topography under sea waves. Sample results are given for a ridge and a canyon. In particular the dynamic pore pressure and the combined static and dynamic effective stresses are presented. 10 references, 11 figures.

Design of a Horizontal Penetrometer for Measuring On‑the‑Go Soil Resistance

Directory of Open Access Journals (Sweden)

Davut Karayel

2010-10-01

Full Text Available Soil compaction is one of the main negative factors that limits plant growth and crop yield. Therefore, it is important to determine the soil resistance level and map it for the field to find solutions for the negative effects of the compaction. Nowadays, high powered communication technology and computers help us on this issue within the approach of precision agriculture applications. This study is focused on the design of a penetrometer, which can make instantaneous soil resistance measurements in the soil horizontally and data acquisition software based on the GPS (Global Positioning System. The penetrometer was designed using commercial 3D parametric solid modelling design software. The data acquisition software was developed in Microsoft Visual Basic.NET programming language. After the design of the system, manufacturing and assembly of the system was completed and then a field experiment was carried out. According to the data from GPS and penetration resistance values which are collected in Microsoft SQL Server database, a Kriging method by ArcGIS was used and soil resistance was mapped in the field for a soil depth of 40 cm. During operation, no faults, either in mechanical and software parts, were seen. As a result, soil resistance values of 0.2 MPa and 3 MPa were obtained as minimum and maximum values, respectively. In conclusion, the experimental results showed that the designed system works quite well in the field and the horizontal penetrometer is a practical tool for providing on‑line soil resistance measurements. This study contributes to further research for the development of on-line soil resistance measurements and mapping within the precision agriculture applications.

Design of a horizontal penetrometer for measuring on-the-go soil resistance.

Science.gov (United States)

Topakci, Mehmet; Unal, Ilker; Canakci, Murad; Celik, Huseyin Kursat; Karayel, Davut

2010-01-01

Soil compaction is one of the main negative factors that limits plant growth and crop yield. Therefore, it is important to determine the soil resistance level and map it for the field to find solutions for the negative effects of the compaction. Nowadays, high powered communication technology and computers help us on this issue within the approach of precision agriculture applications. This study is focused on the design of a penetrometer, which can make instantaneous soil resistance measurements in the soil horizontally and data acquisition software based on the GPS (Global Positioning System). The penetrometer was designed using commercial 3D parametric solid modelling design software. The data acquisition software was developed in Microsoft Visual Basic.NET programming language. After the design of the system, manufacturing and assembly of the system was completed and then a field experiment was carried out. According to the data from GPS and penetration resistance values which are collected in Microsoft SQL Server database, a Kriging method by ArcGIS was used and soil resistance was mapped in the field for a soil depth of 40 cm. During operation, no faults, either in mechanical and software parts, were seen. As a result, soil resistance values of 0.2 MPa and 3 MPa were obtained as minimum and maximum values, respectively. In conclusion, the experimental results showed that the designed system works quite well in the field and the horizontal penetrometer is a practical tool for providing on-line soil resistance measurements. This study contributes to further research for the development of on-line soil resistance measurements and mapping within the precision agriculture applications.

Surgical treatment for paralytic horizontal strabismus

Directory of Open Access Journals (Sweden)

Feng Zhou*

2015-08-01

Full Text Available AIM: To observe the effect of surgery for paralytic horizontal strabismus and the paralytic horizontal strabismus performed by Jensen procedure with antagonist muscle of paralytic muscle recession and medial or lateral rectus extra large resection/recession.METHODS: Fifteen cases(17 eyeswith complete or nearly complete paralytic horizontal strabismus from January 2005 to August. 2014 in our hospital were assessed retrospectively,7 eyes of 7 cases with treatment group A were performed Jensen procedure combined antagonist muscle of paralytic muscle recession, 10 eyes of 8 cases with treatment group B were performed medial or lateral rectus extra large resection/recession. seventeen eyes of 15 cases with an average of 21±8.71mo follow-up were observed.RESULTS: All 17 eyes of 15 cases after the operation obtained satisfied effects, 16 eyes of 14 cases obtained ideal long-term effect. One eye of a patient with a 6mo follow-up was undercorrected of 30△. We found a varying degree of postoperative improvement in visual function. There was a significant reduction in the strabismus angle for distance and near(t=28.71, Pt=36.21, Pt=17.96, Pt=9.20,PCONCLUSION: Jensen procedure combined antagonist muscle of paralytic muscle recession and medial or lateral rectus extra large resection/recession is a safe and successful method of treatment in complete or nearly complete paralysis horizontal strabismus. Patients achieve orthophoria, improvement of the motor ability, and larger field of binocular single vision for long time.

Implications for anomalous mantle pressure and dynamic topography from lithospheric stress patterns in the North Atlantic Realm

DEFF Research Database (Denmark)

Schiffer, Christian; Nielsen, Søren Bom

2016-01-01

With convergent plate boundaries at some distance, the sources of the lithospheric stress field of the North Atlantic Realm are mainly mantle tractions at the base of the lithosphere, lithospheric density structure and topography. Given this, we estimate horizontal deviatoric stresses using a wel...

Efficiency calibration and minimum detectable activity concentration of a real-time UAV airborne sensor system with two gamma spectrometers.

Science.gov (United States)

Tang, Xiao-Bin; Meng, Jia; Wang, Peng; Cao, Ye; Huang, Xi; Wen, Liang-Sheng; Chen, Da

2016-04-01

A small-sized UAV (NH-UAV) airborne system with two gamma spectrometers (LaBr3 detector and HPGe detector) was developed to monitor activity concentration in serious nuclear accidents, such as the Fukushima nuclear accident. The efficiency calibration and determination of minimum detectable activity concentration (MDAC) of the specific system were studied by MC simulations at different flight altitudes, different horizontal distances from the detection position to the source term center and different source term sizes. Both air and ground radiation were considered in the models. The results obtained may provide instructive suggestions for in-situ radioactivity measurements of NH-UAV. Copyright © 2016 Elsevier Ltd. All rights reserved.

Superposition of Stress Fields in Diametrically Compressed Cylinders

Directory of Open Access Journals (Sweden)

João Augusto de Lima Rocha

Full Text Available Abstract The theoretical analysis for the Brazilian test is a classical plane stress problem of elasticity theory, where a vertical force is applied to a horizontal plane, the boundary of a semi-infinite medium. Hypothesizing a normal radial stress field, the results of that model are correct. Nevertheless, the superposition of three stress fields, with two being based on prior results and the third based on a hydrostatic stress field, is incorrect. Indeed, this work shows that the Cauchy vectors (tractions are non-vanishing in the parallel planes in which the two opposing vertical forces are applied. The aim of this work is to detail the process used in the construction of the theoretical model for the three stress fields used, with the objective being to demonstrate the inconsistency often stated in the literature.

Demonstration of a utility industry horizontal drilling system: Horizontal well AMH-5 installation report

International Nuclear Information System (INIS)

1992-01-01

The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies and systems for cleanup of VOCs in soils and groundwater at the Savannah River Site (SRS) in 1989. The overall goal of the program is demonstration of multiple technologies and systems in the fields of drilling, characterization, monitoring, and remediation at a single test bed. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program. Directional drilling has been shown to be a successful technique for enhancing access to the subsurface, thus improving remediation systems, especially remediation systems which perform in situ. Demonstration of an innovative directional drilling system at the Integrated Demonstration Site at the SRS, was initiated in June of 1992. The directional drilling system was designed to install an in situ remediation system. The drilling system is an experimental compaction/dry drilling technique developed by Charles Machine Works (Ditch Witch reg-sign) of Perry, Oklahoma. A horizontal well was installed in the M Area of the SRS below and parallel to an abandoned tile process sewer line. The installation of the horizontal well was a two-part process. Part one consisted of drilling the borehole, and part two was the horizontal well completion

On elastic waves in an thinly-layered laminated medium with stress couples under initial stress

Directory of Open Access Journals (Sweden)

P. Pal Roy

1988-01-01

Full Text Available The present work is concerned with a simple transformation rule in finding out the composite elastic coefficients of a thinly layered laminated medium whose bulk properties are strongly anisotropic with a microelastic bending rigidity. These elastic coefficients which were not known completely for a layered laminated structure, are obtained suitably in terms of initial stress components and Lame's constants λi, μi of initially isotropic solids. The explicit solutions of the dynamical equations for a prestressed thinly layered laminated medium under horizontal compression in a gravity field are derived. The results are discussed specifying the effects of hydrostatic, deviatoric and couple stresses upon the characteristic propagation velocities of shear and compression wave modes.

Convection flow study within a horizontal fluid layer under the action of gas flow

Directory of Open Access Journals (Sweden)

Kreta Aleksei

2016-01-01

Full Text Available Experimental investigation of convective processes within horizontal evaporating liquid layer under shear–stress of gas flow is presented. It is found the structures of the convection, which move in opposite direction relative to each other. First convective structure moves in reverse direction with the flow of gas, and the second convective structure moves towards the gas flow. Convection flow within the liquid layer is registered with help of PIV technique. Average evaporation flow rate of Ethanol liquid layer under Air gas flow is measured. Influence of the gas velocity, at a constant temperature of 20 °C, on the evaporation flow rate has been studied.

Vacuum horizontal drainage for depressurization of uranium tailings

International Nuclear Information System (INIS)

Pakalnis, R.; Chedsey, G.; Robertson, A.M.; Follin, S.

1985-01-01

A recent advance in tailings slope depressurization is the application of vacuum assist horizontal drainage. Horizontal drains have been used for several decades to reduce water pressures in slopes in order to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by induced negative atmospheric pressures. The vacuum assist system has, since its inception in 1982, been successfully employed at two soil and four rock slope projects located in Western Canada. This paper describes the first application of this system in the United States. The technical feasibility of employing vacuum assisted horizontal drains to depressurize a uranium tailings dam near Riverton, Wyoming has been evaluated. Two horizontal drains (300 ft.) were installed and their effect monitored by nine piezometers. The study was conducted over a three-week internal with vacuum being applied for three and four day periods. The drawdowns achieved through vacuum drainage was found to be approximately double that obtained by gravity alone. The volume of water exhausted under vacuum during the seven day interval was approximately double that obtained by gravity alone

Should tsunami simulations include a nonzero initial horizontal velocity?

Science.gov (United States)

Lotto, Gabriel C.; Nava, Gabriel; Dunham, Eric M.

2017-08-01

Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require initial conditions on sea surface height and depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). Full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor confirm that substantial horizontal momentum is imparted to the ocean. However, almost all of that initial momentum is carried away by ocean acoustic waves, with negligible momentum imparted to the tsunami. We also compare tsunami propagation in each simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial velocity. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves from ocean acoustic and seismic waves at some final time, and backpropagating the tsunami waves to their initial state by solving the

The feature of the focal mechanism solutions and tectonic stress field around the focus of Zaduo earthquake (Ms 6.3) in eastern Tibet

Science.gov (United States)

Yang, Y.; Zeng, Z.; Shuang, X.; Li, X.

2017-12-01

On 17th October, 2016, an earthquake of Ms6.3 occurred in Zaduo County, Qinghai Province (32.9°N, 95.0°E), 159 km away from the epicenter of Yushu Ms7.3 earthquake in 2011. The earthquake is located in the eastern Tibet Plateau and the north region of Eastern Himalayan Syntaxis. Using the broadband seismic waveform data form regional networks, we determined the focal mechanism solutions (FMSs) of 83 earthquakes (M>3.5) occurred in Zaduo and its adjacent areas from 2009 to 2017. We also collected another 63 published FMSs and then inversed the current tectonic stress field in study region using the damped linear inversion method. The results show that the Zaduo earthquake is a normal oblique earthquake. The FMSs in our study region are mainly in strike-slip and normal fault patterns. The strike-slip earthquakes are mainly distributed in Yushu-Ganzi, Zaduo and Yanshiping fault zones, and the normal faulting events occurred in Nu Jiang fault zone and Nierong County and its vicinity, the south and southwest of the study areas. The tectonic stress field results indicate that the stress distribution in the north and east of the study region changes homogeneously and slowly. From west to east, the σ1 gradually changes from NNE to NE direction, and the σ3 varies from NWW to NW direction. Both the maximum (σ1) and minimum (σ3) principal stress axes in the study area are nearly horizontal, except in the Nu Jiang fault zone and its vicinity, the south of the study area, which is in a normal faulting stress regime (σ1 is vertical and σ3 is horizontal). The localized normal faulting stress field in the south area, which is almost limited in a semicircle, indicates that a high pressure and low viscosity body with low S-wave velocity and high conductivity might exists beneath the anomaly area. And there may be another semicircle abnormal area beyond the south of the study region. Waveform data for this study are provided by Data Management Centre of China National Seismic

Minimum income protection in the Netherlands

NARCIS (Netherlands)

van Peijpe, T.

2009-01-01

This article offers an overview of the Dutch legal system of minimum income protection through collective bargaining, social security, and statutory minimum wages. In addition to collective agreements, the Dutch statutory minimum wage offers income protection to a small number of workers. Its

Horizontal Multinational Firms, Vertical Multinational Firms and Domestic Investment

NARCIS (Netherlands)

J. Emami Namini (Julian); H.P.G. Pennings (Enrico)

2009-01-01

textabstractWe build a dynamic general equilibrium model with 2 countries, horizontal and vertical multinational activity and endogenous domestic and foreign investment. It is found that horizontal multinational activity always leads to a complementary relationship between domestic and foreign

Resolution of thermal striping issue downstream of a horizontal pipe elbow in stratified pipe flow. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Kuzay, T.M.; Kasza, K.E.

1985-01-01

A thermally stratified pipe flow produced by a thermal transient when passing through a horizontal elbow as a result of secondary flow gives rise to large thermal fluctuations on the inner curvature wall of the downstream piping. These fluctuations were measured in a specially instrumented horizontal pipe and elbow system on a test set-up using water in the Mixing Components Technology Facility (MCTF) at Argonne National Laboratory (ANL). This study is part of a larger program which is studying the influence of thermal buoyancy on general reactor component performance. This paper discusses the influence of pipe flow generated thermal oscillations on the thermal stresses induced in the pipe walls. The instrumentation was concentrated around the exit plane of the 90/sup 0/ sweep elbow, since prior tests had indicated that the largest thermal fluctuations would occur within about one hydraulic diameter downstream of the elbow exit. The thermocouples were located along the inner curvature of the piping and measured the near surface fluid temperature. The test matrix involved thermal downramps under turbulent flow conditions.

The Interplay of In Situ Stress Ratio and Transverse Isotropy in the Rock Mass on Prestressed Concrete-Lined Pressure Tunnels

Science.gov (United States)

Simanjuntak, T. D. Y. F.; Marence, M.; Schleiss, A. J.; Mynett, A. E.

2016-11-01

This paper presents the mechanical and hydraulic behaviour of passively prestressed concrete-lined pressure tunnels embedded in elastic transversely isotropic rocks subjected to non-uniform in situ stresses. Two cases are distinguished based on whether the in situ vertical stress in the rock mass is higher, or lower than the in situ horizontal stress. A two-dimensional finite element model was used to study the influence of dip angle, α, and horizontal-to-vertical stress ratio, k, on the bearing capacity of prestressed concrete-lined pressure tunnels. The study reveals that the in situ stress ratio and the orientation of stratifications in the rock mass significantly affect the load sharing between the rock mass and the lining. The distribution of stresses and deformations as a result of tunnel construction processes exhibits a symmetrical pattern for tunnels embedded in a rock mass with either horizontal or vertical stratification planes, whereas it demonstrates an unsymmetrical pattern for tunnels embedded in a rock mass with inclined stratification planes. The results obtained for a specific value α with coefficient k are identical to that for α + 90° with coefficient 1/ k by rotating the tunnel axis by 90°. The maximum internal water pressure was determined by offsetting the prestress-induced hoop strains at the final lining intrados against the seepage-induced hoop strains. As well as assessing the internal water pressure, this approach is capable of identifying potential locations where longitudinal cracks may occur in the final lining.

Effects of horizontal plyometric training volume on soccer players' performance.

Science.gov (United States)

Yanci, Javier; Los Arcos, Asier; Camara, Jesús; Castillo, Daniel; García, Alberto; Castagna, Carlo

2016-01-01

The aim of this study was to examine the dose response effect of strength and conditioning programmes, involving horizontally oriented plyometric exercises, on relevant soccer performance variables. Sixteen soccer players were randomly allocated to two 6-week plyometric training groups (G1 and G2) differing by imposed (twice a week) training volume. Post-training G1 (4.13%; d = 0.43) and G2 (2.45%; d = 0.53) moderately improved their horizontal countermovement jump performance. Significant between-group differences (p  0.05, d = trivial or small) post-training improvements in sprint, change of direction ability (CODA) and horizontal arm swing countermovement jump were reported in either group. Horizontal plyometric training was effective in promoting improvement in injury prevention variables. Doubling the volume of a horizontal plyometric training protocol was shown to have no additional effect over functional aspects of soccer players' performance.

Evaluation of horizontal magnification on panoramic images

Directory of Open Access Journals (Sweden)

Maryam Raoof

2013-01-01

Full Text Available Aims: This study evaluated the horizontal magnification of images taken from adults and pediatrics with PM 2002 CC Planmeca analogue machine. Materials and Methods: A series of 120 panoramic radiographs were obtained of 60 adults and 60 pediatrics. For all patients, negative impressions were used to make positive casts of the teeth. A caliper was used to measure the maximum mesiodistal length of the buccal surface of all teeth except canines on both casts and radiographs. The horizontal magnification factor was calculated for incisor, premolar, and molar regions by dividing the values obtained from the casts by the values obtained from the radiographs. Statistical Analysis: Independent t-test and one-way analysis of variance (ANOVA were used. Results: The results indicated that with regard to adults, maxillary and mandibular incisor regions, unlike the other two sessions, didn′t show significant difference of the mean magnification of horizontal dimension (P = 0.5. In pediatrics, the comparison between mean magnification factors of all subgroups showed significant difference (P < 0.0001. Despite the adults′ radiographs, the results of pediatrics′ radiographs showed significantly higher magnification than the index listed by the manufacturer of the radiographic machine used. Conclusion: The present study results point to the fact that PM 2002 CC Proline panoramic machine makes possible precise measurements on radiographs of adults′ jaws in the horizontal dimension.

On the effects of gravity and sulfur content on the weld shape in horizontal narrow gap GTAW of stainless steels

KAUST Repository

Traidia, Abderrazak

2013-07-01

A simplified 2D axisymmetric model and a comprehensive 3D weld pool model, accounting for the free surface deformation and the filler metal addition, have been developed to investigate the factors that lead to asymmetric bead shapes in horizontal GTA welding of stainless steels. Buoyancy-induced flow and the sagging of the pool free surface, under the action of gravity, are found to be responsible for the weld asymmetry and the decrease in the weld penetration at the bottom sidewall. The numerical results clearly emphasized the beneficial role of the Marangoni shear stress in limiting the asymmetry of horizontal GTA welds. An additional experimental investigation showed that the asymmetry in the weld shape can be reduced when placing the lowest sulfur content component at the bottom side. © 2013 Elsevier B.V. All rights reserved.

Economical Optimization of the Mechanized Longwall Faces with Top Coal Caving Mining, In Horizontal Slices

Science.gov (United States)

Onica, Ilie; Mihăilescu, Viorel; Andrioni, Felicia

2016-09-01

To increase the economic and technical performances of the Jiu Valley hard coal mines, the top coal caving, in horizontal slices, mining methods (Bourbaki methods) were introduced, adapted to the local geo-mining conditions. This mining was successfully experimented by using classical technology, using the individual supports and coal blasting. In the future, it is planned to adopt the mechanized technology, with frame supports and shearers. The mechanized longwall faces with top coal caving mining, in horizontal slices, of coal seam no. 3 could be efficient only if the sizes of the top coal height and the panel length determine a minimum cost of production. Therefore, the goal of this paper is the optimization of these parameters, from a technical and economic point of view, taking into account the general model of the cost function, at the panel level. For that, it was necessary to make a certain sequence of analysis involving: technological unit establishment, purpose function and optimizing model. Thus, there attaining to the mathematical model of the unit cost, after determination of all the individual calculation articles, regarding the preparatory workings, coal face equipments, materials, energy, workforce, etc. Because of the complexity of the obtained technical and economic model, to determine the optimum sizes of the panel length and top coal height, it was necessary to archive a sensitivity analysis of the unit cost function to the main parameters implied into this mathematical model.

Horizontal-Longitudinal Correlations of Acoustic Field in Deep Water

International Nuclear Information System (INIS)

Li Jun; Li Zheng-Lin; Ren Yun; Li Wen; Zhang Ren-He

2015-01-01

The horizontal-longitudinal correlations of the acoustic field in deep water are investigated based on the experimental data obtained in the South China Sea. It is shown that the horizontal-longitudinal correlation coefficients in the convergence zone are high, and the correlation length is consistent with the convergence zone width, which depends on the receiver depth and range. The horizontal-longitudinal correlation coefficients in the convergence zone also have a division structure for the deeper receiver. The signals from the second part of the convergence zone are still correlated with the reference signal in the first part. The horizontal-longitudinal correlation coefficients in the shadow zone are lower than that in the convergence zone, and the correlation length in the shadow zone is also much shorter than that in the convergence zone. The numerical simulation results by using the normal modes theory are qualitatively consistent with the experimental results. (paper)

Minimum exposure limits and measured relationships between the vitamin D, erythema and international commission on non-ionizing radiation protection solar ultraviolet.

Science.gov (United States)

Downs, Nathan; Parisi, Alfio; Butler, Harry; Turner, Joanna; Wainwright, Lisa

2015-01-01

The International Commission on Non-Ionizing Radiation Protection (ICNIRP) has established guidelines for exposure to ultraviolet radiation in outdoor occupational settings. Spectrally weighted ICNIRP ultraviolet exposures received by the skin or eye in an 8 h period are limited to 30 J m(-2). In this study, the time required to reach the ICNIRP exposure limit was measured daily in 10 min intervals upon a horizontal plane at a subtropical Australian latitude over a full year and compared with the effective Vitamin D dose received to one-quarter of the available skin surface area for all six Fitzpatrick skin types. The comparison of measured solar ultraviolet exposures for the full range of sky conditions in the 2009 measurement period, including a major September continental dust event, show a clear relationship between the weighted ICNIRP and the effective vitamin D dose. Our results show that the horizontal plane ICNIRP ultraviolet exposure may be used under these conditions to provide minimum guidelines for the healthy moderation of vitamin D, scalable to each of the six Fitzpatrick skin types. © 2014 The American Society of Photobiology.

Stratigraphy and Stress History Recorded by a Complex Volcano-Tectonic Feature in the Nemesis Tessera Quadrangle, Venus

Science.gov (United States)

Doggett, T. C.; Grosfils, E. B.

2002-01-01

The stress history of a feature, identified as a previously uncataloged dike swarm, at 45N 191E is mapped as clockwise rotation of maximum horizontal compressive stress. It is intermediate between areas associated with compression, mantle upwelling and convection. Additional information is contained in the original extended abstract.

Effect of extender oils on the stress relaxation behavior of thermoplastic vulcanizates

Directory of Open Access Journals (Sweden)

2008-11-01

Full Text Available The long term mechanical behavior of oil extended thermoplastic vulcanizates (TPV based on polypropylene (PP and acrylonitrile-butadiene rubber (NBR has been characterized by means of stress relaxation experiments. The morphology of TPV and the phase specific oil distribution which depend on the content and type of oil as well as on the mixing regime have been characterized by means of Atomic Force Microscopy (AFM, Dynamic Mechanical Thermal Analysis (DMTA and Differential Scanning Calorimetrie (DSC. The discussion of the stress relaxation behavior was carried out using the two-component model, which allows splitting the initial stress into two components: a thermal activated stress component and an athermal one. A master curve was created by shifting the relaxation curves vertically and horizontally towards the reference curve. The vertical shift factor bT is a function of the temperature dependence of the athermal stress components. It was found that the oil distribution strongly affects the athermal stress component which is related to the contribution of the structural changes, e.g. crystallinity of the PP phase and the average molecular weight between the crosslinks of the NBR phase. From the temperature dependence of the horizontal shift factor aT the main viscoelastic relaxation process was determined as the α-relaxation process of the crystalline PP phase. It is not dependent on the polarity and content of the oil as well as the mixing regime.

Tectonic stress orientations and magnitudes, and friction of faults, deduced from earthquake focal mechanism inversions over the Korean Peninsula

Science.gov (United States)

Soh, Inho; Chang, Chandong; Lee, Junhyung; Hong, Tae-Kyung; Park, Eui-Seob

2018-05-01

We characterize the present-day stress state in and around the Korean Peninsula using formal inversions of earthquake focal mechanisms. Two different methods are used to select preferred fault planes in the double-couple focal mechanism solutions: one that minimizes average misfit angle and the other choosing faults with higher instability. We invert selected sets of fault planes for estimating the principal stresses at regularly spaced grid points, using a circular-area data-binning method, where the bin radius is optimized to yield the best possible stress inversion results based on the World Stress Map quality ranking scheme. The inversions using the two methods yield well constrained and fairly comparable results, which indicate that the prevailing stress regime is strike-slip, and the maximum horizontal principal stress (SHmax) is oriented ENE-WSW throughout the study region. Although the orientation of the stresses is consistent across the peninsula, the relative stress magnitude parameter (R-value) varies significantly, from 0.22 in the northwest to 0.89 in the southeast. Based on our knowledge of the R-values and stress regime, and using a value for vertical stress (Sv) estimated from the overburden weight of rock, together with a value for the maximum differential stress (based on the Coulomb friction of faults optimally oriented for slip), we estimate the magnitudes of the two horizontal principal stresses. The horizontal stress magnitudes increase from west to east such that SHmax/Sv ratio rises from 1.5 to 2.4, and the Shmin/Sv ratio from 0.6 to 0.8. The variation in the magnitudes of the tectonic stresses appears to be related to differences in the rigidity of crustal rocks. Using the complete stress tensors, including both orientations and magnitudes, we assess the possible ranges of frictional coefficients for different types of faults. We show that normal and reverse faults have lower frictional coefficients than strike-slip faults, suggesting that

Mixed convection-radiation interaction in boundary-layer flow over horizontal surfaces

Science.gov (United States)

Ibrahim, F. S.; Hady, F. M.

1990-06-01

The effect of buoyancy forces and thermal radiation on the steady laminar plane flow over an isothermal horizontal flat plate is investigated within the framework of first-order boundary-layer theory, taking into account the hydrostatic pressure variation normal to the plate. The fluid considered is a gray, absorbing-emitting but nonscattering medium, and the Rosseland approximation is used to describe the radiative heat flux in the energy equation. Both a hot surface facing upward and a cold surface facing downward are considered in the analysis. Numerical results for the local Nusselt number, the local wall shear stress, the local surface heat flux, as well as the velocity and temperature distributions are presented for gases with a Prandtl number of 0.7 for various values of the radiation-conduction parameter, the buoyancy parameter, and the temperature ratio parameter.

Model and calculation of in situ stresses in anisotropic formations

Energy Technology Data Exchange (ETDEWEB)

Yuezhi, W.; Zijun, L.; Lixin, H. [Jianghan Petroleum Institute, (China)

1997-08-01

In situ stresses in transversely isotropic material in relation to wellbore stability have been investigated. Equations for three horizontal in- situ stresses and a new formation fracture pressure model were described, and the methodology for determining the elastic parameters of anisotropic rocks in the laboratory was outlined. Results indicate significantly smaller differences between theoretically calculated pressures and actual formation pressures than results obtained by using the isotropic method. Implications for improvements in drilling efficiency were reviewed. 13 refs., 6 figs.

Present-day Horizontal Mobility in the Serbian Part of the Pannonian Basin; Inferences from the Geometric Analysis of Deformations

Science.gov (United States)

Sušić, Zoran; Toljić, Marinko; Bulatović, Vladimir; Ninkov, Toša; Stojadinović, Uroš

2016-10-01

In tectonically complex environments, such as the Pannonian Basin surrounded by the Alps-Dinarides and Carpathians orogens, monitoring of recent deformations represents very challenging matter. Efficient quantification of active continental deformations demands the use of a multidisciplinary approach, including neotectonic, seismotectonic and geodetic methods. The present-day tectonic mobility in the Pannonian Basin is predominantly controlled by the northward movement of the Adria micro-plate, which has produced compressional stresses that were party accommodated by the Alps-Dinarides thrust belt and partly transferred towards its hinterland. Influence of thus induced stresses on the recent strain field, deformations and tectonic mobility in the southern segment of the Pannonian Basin has been investigated using GPS measurements of the horizontal mobility in the Vojvodina area (northern Serbia).

Seismic stress analysis of feeder lines to LOFT primary coolant pump motors

International Nuclear Information System (INIS)

Kuehster, C.J.

1978-01-01

The conduit system in the LOFT Support Building was analyzed for seismic loading. The conduit itself plus its various supports were subjected to both horizontal and vertical forces. The results show the system loads or stresses to be within allowables

Understanding the Minimum Wage: Issues and Answers.

Science.gov (United States)

Employment Policies Inst. Foundation, Washington, DC.

This booklet, which is designed to clarify facts regarding the minimum wage's impact on marketplace economics, contains a total of 31 questions and answers pertaining to the following topics: relationship between minimum wages and poverty; impacts of changes in the minimum wage on welfare reform; and possible effects of changes in the minimum wage…

Youth minimum wages and youth employment

NARCIS (Netherlands)

Marimpi, Maria; Koning, Pierre

2018-01-01

This paper performs a cross-country level analysis on the impact of the level of specific youth minimum wages on the labor market performance of young individuals. We use information on the use and level of youth minimum wages, as compared to the level of adult minimum wages as well as to the median

Logging while drilling keeps horizontal well on small target

International Nuclear Information System (INIS)

Leake, J.; Shray, F.

1991-01-01

This paper reports that the logging-while-drilling (LWD) measurement to two resistivities of different characteristics had led to a new interpretation method for the analysis of horizontal wells. By logging deep and shallow resistivity in real-time, marker beds were identified to help maintain well bore trajectory. The resistivity measurements were split into vertical and horizontal components to provide additional information of formation evaluation. In 1945, Ark Fuel Co. discovered and began developing the Olla field on the crest of the La Salle arch in La Salle Parish, La. Oil production comes from the Wilcox formation from alluvial sand packages that range in thickness from 3 ft to 120 ft. Now operated by Oxy U.S.A. Inc., Olla field was chosen in 1990 for a horizontal well pilot project. It was hoped that a horizontal well could alleviate water coming in one of the field's more productive sand packages- the 40-ft Cruse sand

Discretization of space and time: determining the values of minimum length and minimum time

OpenAIRE

Roatta , Luca

2017-01-01

Assuming that space and time can only have discrete values, we obtain the expression of the minimum length and the minimum time interval. These values are found to be exactly coincident with the Planck's length and the Planck's time but for the presence of h instead of ħ .

Minimum wage development in the Russian Federation

OpenAIRE

Bolsheva, Anna

2012-01-01

The aim of this paper is to analyze the effectiveness of the minimum wage policy at the national level in Russia and its impact on living standards in the country. The analysis showed that the national minimum wage in Russia does not serve its original purpose of protecting the lowest wage earners and has no substantial effect on poverty reduction. The national subsistence minimum is too low and cannot be considered an adequate criterion for the setting of the minimum wage. The minimum wage d...

Effectiveness of Horizontal Rebar on Concrete Block Retaining Wall Strength

OpenAIRE

Krishpersad Manohar; Rikhi Ramkissoon

2016-01-01

The effectiveness of including a horizontal rebar compared to only a vertical rebar in concrete filled core interlocking concrete block retaining wall sections was investigated with respect to the horizontal retaining force. Experimental results for three specimens of interlocking blocks with vertical rebar and concrete filled cores showed an average horizontal retaining force of 24546 N ± 5.7% at an average wall deflection of 13.3 mm. Experimental results for three wall specimens of interloc...

Improving steamflood effectiveness by horizontal producers

Energy Technology Data Exchange (ETDEWEB)

Leonhardt, B. [Wintershall AG, Barnstorf (Germany)

2001-12-01

The Emlichheim oilfield is located in North-West-Germany on the Dutch-German border being the Southern downdip part of the Schoonebeek anticline. The field was discovered in 1943 and came on production in 1944. Since production startup, Wintershall operates the field as owner of the concession (90% share of interest) in a joint venture with Mobil Erdgas-Erdoel GmbH (10%). For more than 50 years an average crude oil production of 150.000 t/year has been maintained. Starting with huff ''n'' puff and hot water flooding in the late 60's, the first steam flood project was implemented in 1981. Further steamflood projects started in 1989, 1992, 1993, 1994 and 1998 in different areas of the field. Until 1997, only vertical production wells were drilled in the field. Wellbore stability seemed to be a major problem for drilling horizontal wells in the unconsolidated sandstone reservoir at that time. In 1999 an innovative steamflood project was started with three newly drilled horizontal producers surrounding a vertical steam injector. First results are showing a significant improvement in the performance as compared to the earlier projects and offer new chances for further development of the field. Today, the field could no longer be operated without the steam projects as roughly 95% of the field production is coming from thermal EOR. This paper gives a brief overview of the field and its production history, the planning and realization of a current steamflood project using horizontal well technology as well as its performance compared to the earlier projects. It also describes the experience of drilling horizontal wells in the unconsolidated sandstone. A brief outlook to the future field development is given. (orig.)

Horizontal Stratification in Access to Danish University Programmes

DEFF Research Database (Denmark)

Munk, Martin D.; Thomsen, Jens Peter

2018-01-01

a relatively detailed classification of parents’ occupations to determine how students are endowed with different forms of capital, even when their parents would typically be characterised as belonging to the same social group. Second, we distinguish among disciplines and among university institutions...... to explain the dynamics of horizontal stratification in the Danish university system. Using unique and exhaustive register data, including all higher education institutions and the entire 1984 cohort as of the age of 24, we uncover distinct differences in the magnitude and type of horizontal stratification...... in different fields of study and university institutions. Most importantly, we find distinct patterns of horizontal stratification by field of study and parental occupation that would have remained hidden had we used more aggregated classifications for field of study and social origin....

Remaining life case history studies for high energy piping systems using equivalent stress

International Nuclear Information System (INIS)

Cohn, M.J.

1987-01-01

As the development of plant life extension for high energy piping systems is progressing, conventional piping system design methodologies are also being reevaluated. Traditional guidelines such as American National Standard Institute/American Society of Mechanical Engineers B31.1 (ANSI/ASME) were developed for plants having design lives in the 25- to 30-year regime based upon relatively short-term base metal creep data. These guidelines use a simplified approach for the piping analysis. Two types of stress criteria must be satisfied. The first type is longitudinal plus torsion stress checks for several types of loading conditions versus the material allowable stresses. The second type is an independent minimum wall thickness check which considers the hoop stress versus the material allowable stress. Seven case histories have been evaluated to estimate the minimum piping system creep life based on the current ANSI/ASME B31.1 finite element type of analysis, which is a traditional approach, versus a multiaxial stress state type of analysis. In nearly every case, the equivalent stress methodology predicted significantly higher stresses. Consequently, the equivalent stress methodology resulted in 11 to 96% lower time to rupture values as compared to the values predicted using ANSI/ASME B31.1 stresses

The measurement of in-situ stress in near surface environments

International Nuclear Information System (INIS)

Garritty, P.; Irvin, R.A.

1984-04-01

One of the major unknowns affecting aspects of underground construction and the geohydrology of rock masses is the magnitude and direction of the geostatic principal stresses in the earth's crust. This is particularly the case in near surface rocks where there are indications that high horizontal stresses may exist. The measurement of stress in near surface environments is particularly difficult. The techniques, experience and results of a geostatic stress measurement programme using four commercially available devices at shallow depth in the Carnmenellis Granite are critically discussed and compared. This report also brings together some of the conclusions of two previous reports in the series, Garritty (1983) and Garritty and Irvin (1983), and emphasises the fundamental relationship between the state of stress in the earth's crust and the geohydrology of rock masses. (author)

Minimum emittance of three-bend achromats

International Nuclear Information System (INIS)

Li Xiaoyu; Xu Gang

2012-01-01

The calculation of the minimum emittance of three-bend achromats (TBAs) made by Mathematical software can ignore the actual magnets lattice in the matching condition of dispersion function in phase space. The minimum scaling factors of two kinds of widely used TBA lattices are obtained. Then the relationship between the lengths and the radii of the three dipoles in TBA is obtained and so is the minimum scaling factor, when the TBA lattice achieves its minimum emittance. The procedure of analysis and the results can be widely used in achromats lattices, because the calculation is not restricted by the actual lattice. (authors)

The fatigue behavior of composite laminates under various mean stresses

Science.gov (United States)

Rotem, A.

1991-01-01

A method is developed for predicting the S-N curve of a composite laminate which is subjected to an arbitrary stress ratio, R (minimum stress/maximum stress). The method is based on the measuring of the S-N behavior of two distinct cases, tension-tension and compression-compression fatigue loadings. Using these parameters, expressions are formulated that estimate the fatigue behavior under any stress ratio loading. Experimental results from the testing of graphite/epoxy laminates, with various structures, are compared with the predictions and show good agreement.

Remediation of a contaminated thin aquifer by horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Breh, W.; Suttheimer, J.; Hoetzl, H. [Univ. of Karlsruhe (Germany); Frank, K. [GEO-Service GmbH, Rheinmuenster (Germany)

1997-12-31

At an industrial site in Bruchsal (Germany) a huge trichloroethene contamination was found. After common remedial actions proved to be widely ineffective, new investigations led to a highly contaminated thin aquifer above the main aquifer. The investigation and the beginning of the remediation of the thin aquifer by two horizontal wells is described in this paper. Special attention was given to the dependence between precipitation and the flow direction in the thin aquifer and to hydraulic connections between the thin and the main aquifer. Also a short introduction into a new remedial technique by horizontal wells and first results of the test phase of the horizontal wells are given.

Research on stress distribution regularity of cement sheaths of radial well based on ABAQUS

Science.gov (United States)

Shi, Jihui; Cheng, Yuanfang; Li, Xiaolong; Xiao, Wen; Li, Menglai

2017-12-01

To ensure desirable outcome of hydraulic fracturing based on ultra-short radius radial systems, it is required to investigate the stress distribution regularity and stability of the cement sheath. On the basis of the theoretical model of the cement sheath stress distribution, a reservoir mechanical model was built using the finite element software, ABAQUS, according to the physical property of a certain oil reservoir of the Shengli oilfield. The stress distribution of the casing-cement-sheath-formation system under the practical condition was simulated, based on which analyses were conducted from multiple points of view. Results show that the stress on the internal interface of the cement sheath exceeds that on the external interface, and fluctuates with higher amplitudes, which means that the internal interface is the most failure-prone. The unevenness of the cement sheath stress distribution grows with the increasing horizontal principal stress ratio, and so does the variation magnitude. This indicates that higher horizontal principal stress ratios are unfavourable for the structural stability of the cement sheath. Both the wellbore quantity of the URRS and the physical property of the material can affect the cement sheath distribution. It is suggested to optimize the quantity of the radial wellbore and use cement with a lower elastic modulus and higher Poisson’s ratio. At last, the impact level of the above factor was analysed, with the help of the grey correlation analysis.

30 CFR 57.19021 - Minimum rope strength.

Science.gov (United States)

2010-07-01

... feet: Minimum Value=Static Load×(7.0−0.001L) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0. (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0. (c) Tail...

30 CFR 56.19021 - Minimum rope strength.

Science.gov (United States)

2010-07-01

... feet: Minimum Value=Static Load×(7.0-0.001L) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0-0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes...

Analysis of rock stress and rock stress measurements with application to Aespoe HRL

International Nuclear Information System (INIS)

Lundholm, Beatrice

2000-11-01

The process of choosing a site for a nuclear waste repository means that many aspects have to be taken into consideration. One of these is that the repository has to be mechanically stable for a long time. The mechanical stability of the rock is very difficult to determine. One of several factors, which determine the mechanical stability, is the virgin state of stress. The thesis project consists of two parts. In the first part the state of stress at Aespoe Hard Rock Laboratory had to be defined. This was done based on earlier rock stress measurements conducted during the years 1988 to 1997. Two different measurement techniques have been used, hydraulic fracturing and overcoring. During the overcoring two types of cells have been used, CSIRO HI-cell and a cell developed by the Swedish State Power Board (SSPB). In the second part of the project, investigation of the correlation between the stress and geological structures are made using numerical modelling tools such as FLAC, UDEC and 3DEC. The rock stress measurements using the hydraulic fracturing gave orientations of the horizontal stress that coincide with earlier hydraulic fracturing measurements conducted in Scandinavia. The magnitudes of rock stresses are slightly lower than the earlier reported stress magnitudes for the Scandinavian part of the earth crust. The rock stresses obtained from the overcoring resulted in higher stresses than what was predicted by the hydraulic fracturing measurements. However, the orientation of the maximum horizontal stresses coincides well between the two techniques. The orientation is also more or less constant with respect to increasing depth. The state of stress at Aespoe is defined by using the results from the hydraulic fracturing and the measurements conducted by SSPB-cell. The measurements from the SSPB-cell are used since these have a Poisson's ratio that corresponds well with the uniaxial tests of rock samples and since the measurements have been done at a distance from

Principal permeability determination from multiple horizontal well tests

Energy Technology Data Exchange (ETDEWEB)

Economides, M. [Texas A and M Univ., TX (United States); Munoz, A.; Ehlig-Economides, C.

1998-12-31

A method for obtaining principal permeability magnitudes and direction that requires only the linear flow regime from transient tests in three horizontal wells oriented in three distinct and arbitrary directions, is described. Well design optimization strategies require knowledge of both the principal permeability orientation as well as the horizontal permeability magnitudes. When the degree of horizontal permeability anisotropy (i.e. permeability in the bedding plane with respect to direction) is significant, the productivity of a long horizontal well will depend greatly on its direction, especially when the well is first brought into production. Productivities have been found to deviate substantially among wells in the same reservoir and this deviation has been attributed to differences in well orientation. In view of this fact, measuring permeability anisotropy becomes a compelling necessity. The success of the proposed method is illustrated by a case study in which the principal permeability magnitudes and direction from three wells were used to predict the productivity of a fourth well within 10 per cent. Use of the computed principal permeabilities from the case study, it was possible to forecast the cumulative production to show the significance of well trajectory optimization on the discounted cash flow and the net present value. 20 refs., 3 figs.

Estimation of network parameters with consideration of the horizontal refraction influence

Directory of Open Access Journals (Sweden)

Ján Ježko

2007-06-01

Full Text Available The proposed paper is focused on reviewing the horizontal refraction during measurement in local geodetic networks. Based on elaborated theoretical assumptions the refraction model was arranged in a way that the questions were solved by the identity of the horizontal refraction. The necessary part of the application of the refraction model is the problem of optimizing the geodetic networks and deducting the method of the variance components, which play a major role in the precision of results. The independent acquisition of the thesis lies in the area of modeling the horizontal refraction with a stochastic approach, where the values of the refraction are gained through the measured data of the horizontal direction. In the model, it is necessary to identify the parameters according to the entire measurements and between two points. According to the attained results, I can state that the horizontal refraction was identified mainly on the measurements that were confirmed near the dam in most of the measured experiments. The experimented measurements were confirmed based on the assumptions that are in theoretical capitol, where the assumptions of the effect of the horizontal refraction are measured near the dam, river, shores, and valleys.

Demonstration of in situ-constructed horizontal soil containment barrier at Fernald

International Nuclear Information System (INIS)

Pettit, P.J.; Ridenour, D.; Walker, J.; Saugier, K.

1994-01-01

A new design of jet grouting tool that can be guided by horizontal well casings and that operates in the horizontal plane has been used for the in situ placement of grout and construction of a prototype horizontal barrier that is free of windows. Jet grouting techniques have been advanced to permit construction of horizontal barriers underneath contaminated soil without having to excavate or disturb the waste. The paper describes progress on the Fernald Environmental Restoration Management Corporation (FERMCO) In Situ Land Containment Project which is sponsored by the US Department of Energy's (DOE) Office of Technology Development (OTD) for DOE's Fernald Environmental Management Project (FEMP). The Fernald project is to demonstrate a novel, enabling technology for the controlled underground placement of horizontal panels of grout, and the joining of adjacent panels to construct practical, extensive barriers. Construction strategy, equipment mechanics and operating details of this new method are described

Business models for horizontal collaboration : a practical case study with reusable crates

NARCIS (Netherlands)

Brandi, Teresa

2012-01-01

This project is centered in the topic of horizontal collaboration. The first part focuses on finding business models for horizontal collaboration. The second part is a practical case study at Kuehne + Nagel. Horizontal collaboration consists of two or more independent companies that plan and execute

30 CFR 77.1431 - Minimum rope strength.

Science.gov (United States)

2010-07-01

... feet: Minimum Value=Static Load×(7.0−0.001L) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet or greater: Minimum Value=Static Load×5.0 (c) Tail ropes...

Two-phase flow patterns in horizontal rectangular minichannel

Directory of Open Access Journals (Sweden)

Ron’shin Fedor

2016-01-01

Full Text Available The two-phase flow in a short horizontal channel of rectangular cross-section of 1 × 19 mm2 has been studied experimentally. Five conventional two-phase flow patterns have been detected (bubble, churn, stratified, annular and jet and transitions between them have been determined. It is shown that a change in the width of the horizontal channels has a substantial effect on the boundaries between the flow regimes.

A Phosphate Minimum in the Oxygen Minimum Zone (OMZ) off Peru

Science.gov (United States)

Paulmier, A.; Giraud, M.; Sudre, J.; Jonca, J.; Leon, V.; Moron, O.; Dewitte, B.; Lavik, G.; Grasse, P.; Frank, M.; Stramma, L.; Garcon, V.

2016-02-01

The Oxygen Minimum Zone (OMZ) off Peru is known to be associated with the advection of Equatorial SubSurface Waters (ESSW), rich in nutrients and poor in oxygen, through the Peru-Chile UnderCurrent (PCUC), but this circulation remains to be refined within the OMZ. During the Pelágico cruise in November-December 2010, measurements of phosphate revealed the presence of a phosphate minimum (Pmin) in various hydrographic stations, which could not be explained so far and could be associated with a specific water mass. This Pmin, localized at a relatively constant layer ( 20minimum with a mean vertical phosphate decrease of 0.6 µM but highly variable between 0.1 and 2.2 µM. In average, these Pmin are associated with a predominant mixing of SubTropical Under- and Surface Waters (STUW and STSW: 20 and 40%, respectively) within ESSW ( 25%), complemented evenly by overlying (ESW, TSW: 8%) and underlying waters (AAIW, SPDW: 7%). The hypotheses and mechanisms leading to the Pmin formation in the OMZ are further explored and discussed, considering the physical regional contribution associated with various circulation pathways ventilating the OMZ and the local biogeochemical contribution including the potential diazotrophic activity.

Global seasonal strain and stress models derived from GRACE loading, and their impact on seismicity

Science.gov (United States)

Chanard, K.; Fleitout, L.; Calais, E.; Craig, T. J.; Rebischung, P.; Avouac, J. P.

2017-12-01

Loading by continental water, atmosphere and oceans deforms the Earth at various spatio-temporal scales, inducing crustal and mantelic stress perturbations that may play a role in earthquake triggering.Deformation of the Earth by this surface loading is observed in GNSS position time series. While various models predict well vertical observations, explaining horizontal displacements remains challenging. We model the elastic deformation induced by loading derived from GRACE for coefficients 2 and higher. We estimate the degree-1 deformation field by comparison between predictions of our model and IGS-repro2 solutions at a globally distributed network of 700 GNSS sites, separating the horizontal and vertical components to avoid biases between components. The misfit between model and data is reduced compared to previous studies, particularly on the horizontal component. The associated geocenter motion time series are consistent with results derived from other datasets. We also discuss the impact on our results of systematic errors in GNSS geodetic products, in particular of the draconitic error.We then compute stress tensors time series induced by GRACE loads and discuss the potential link between large scale seasonal mass redistributions and seismicity. Within the crust, we estimate hydrologically induced stresses in the intraplate New Madrid Seismic Zone, where secular stressing rates are unmeasurably low. We show that a significant variation in the rate of micro-earthquakes at annual and multi-annual timescales coincides with stresses induced by hydrological loading in the upper Mississippi embayment, with no significant phase-lag, directly modulating regional seismicity. We also investigate pressure variations in the mantle transition zone and discuss potential correlations between the statistically significant observed seasonality of deep-focus earthquakes, most likely due to mineralogical transformations, and surface hydrological loading.

Real-time horizontal position control for Aditya-upgrade tokamak

International Nuclear Information System (INIS)

Kumar, Rohit; Ghosh, Joydeep; Tanna, Rakesh L.

2015-01-01

Position of plasma column is required to be controlled in real time for improved operation of any tokamak. A PID based system for real-time horizontal plasma position control has been designed for Aditya Upgrade tokamak. Modelling of transfer functions of actuators, plasma and diagnostic system are carried out for ADITYA-U tokamak. The PID controller is optimized using MATLAB-SIMULINK for horizontal position control. Further feed-forward loop is implemented where disturbance due to density variation is suppressed, which results in improved performance as compared to conventional PID operation. In this paper the detailed design of the whole system for real time control of plasma horizontal position in Aditya Upgrade tokamak is presented. (author)

The Karush–Kuhn–Tucker optimality conditions in minimum weight design of elastic rotating disks with variable thickness and density

Directory of Open Access Journals (Sweden)

Sanaz Jafari

2011-10-01

Full Text Available Rotating discs work mostly at high angular velocity. High speed results in large centrifugal forces in discs and induces large stresses and deformations. Minimizing weight of such disks yields various benefits such as low dead weights and lower costs. In order to attain a certain and reliable analysis, disk with variable thickness and density is considered. Semi-analytical solutions for the elastic stress distribution in rotating annular disks with uniform and variable thicknesses and densities are obtained under plane stress assumption by authors in previous works. The optimum disk profile for minimum weight design is achieved by the Karush–Kuhn–Tucker (KKT optimality conditions. Inequality constrain equation is used in optimization to make sure that maximum von Mises stress is always less than yielding strength of the material of the disk.

Heat transfer by natural convection into an horizontal cavity; Transferencia de calor por conveccion natural en una cavidad horizontal

Energy Technology Data Exchange (ETDEWEB)

Arevalo J, P

1998-12-31

At this thesis it is studied the heat transfer by natural convection in an horizontal cavity, it is involved a boiling`s part that is described the regimes and correlations differences for boiling`s curve. It is designed a horizontal cavity for realize the experimental part and it`s mention from equipment or instrumentation to succeed in a experimentation that permits to realize the analysis of heat transfer, handling as water fluid at atmospheric pressure and where it`s present process from natural convection involving part boiling`s subcooled. The system consists of heater zone submerged in a horizontal cavity with water. Once part finished experimental with information to obtained it`s proceeded to obtain a correlation, realized starting from analysis dimensionless such as: Jakob, Bond and Grasoft (Boiling) besides of knows in natural convection: Prandtl and Nusselt. The mathematical model explains the behavior for natural convection continued part boiling`s subcooled. It is realize analysis graphics too where it`s show comparing with Globe Dropkin and Catton equations by natural convection with bottom heating. (Author)

Heat transfer by natural convection into an horizontal cavity; Transferencia de calor por conveccion natural en una cavidad horizontal

Energy Technology Data Exchange (ETDEWEB)

Arevalo J, P

1999-12-31

At this thesis it is studied the heat transfer by natural convection in an horizontal cavity, it is involved a boiling`s part that is described the regimes and correlations differences for boiling`s curve. It is designed a horizontal cavity for realize the experimental part and it`s mention from equipment or instrumentation to succeed in a experimentation that permits to realize the analysis of heat transfer, handling as water fluid at atmospheric pressure and where it`s present process from natural convection involving part boiling`s subcooled. The system consists of heater zone submerged in a horizontal cavity with water. Once part finished experimental with information to obtained it`s proceeded to obtain a correlation, realized starting from analysis dimensionless such as: Jakob, Bond and Grasoft (Boiling) besides of knows in natural convection: Prandtl and Nusselt. The mathematical model explains the behavior for natural convection continued part boiling`s subcooled. It is realize analysis graphics too where it`s show comparing with Globe Dropkin and Catton equations by natural convection with bottom heating. (Author)

Fourth international seminar on horizontal steam generators

Energy Technology Data Exchange (ETDEWEB)

Tuomisto, H. [ed.] [IVO Group, Vantaa (Finland); Purhonen, H. [ed.] [VTT, Espoo (Finland); Kouhia, V. [ed.] [Lappeenranta Univ. of Technology (Finland)

1997-12-31

The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main topics presented in the fourth seminar were: thermal hydraulic experiments and analyses, primary collector integrity, feedwater distributor replacement, management of primary-to-secondary leakage accidents and new developments in the VVER safety technology. The number of participants, representing designers and manufacturers of the horizontal steam generators, plant operators, engineering companies, research organizations, universities and regulatory authorities, was 70 from 10 countries.

Fourth international seminar on horizontal steam generators

Energy Technology Data Exchange (ETDEWEB)

Tuomisto, H [ed.; IVO Group, Vantaa (Finland); Purhonen, H [ed.; VTT, Espoo (Finland); Kouhia, V [ed.; Lappeenranta Univ. of Technology (Finland)

1998-12-31

The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main topics presented in the fourth seminar were: thermal hydraulic experiments and analyses, primary collector integrity, feedwater distributor replacement, management of primary-to-secondary leakage accidents and new developments in the VVER safety technology. The number of participants, representing designers and manufacturers of the horizontal steam generators, plant operators, engineering companies, research organizations, universities and regulatory authorities, was 70 from 10 countries.

Fourth international seminar on horizontal steam generators

International Nuclear Information System (INIS)

Tuomisto, H.; Purhonen, H.; Kouhia, V.

1997-01-01

The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main topics presented in the fourth seminar were: thermal hydraulic experiments and analyses, primary collector integrity, feedwater distributor replacement, management of primary-to-secondary leakage accidents and new developments in the VVER safety technology. The number of participants, representing designers and manufacturers of the horizontal steam generators, plant operators, engineering companies, research organizations, universities and regulatory authorities, was 70 from 10 countries

Potential for horizontal well technology in the U.S

International Nuclear Information System (INIS)

Biglarbigi, K.; Mohan, H.; Ray, R.M.; Meehan, D.N.

2000-01-01

In the past decade, the use of horizontal well technology has increased significantly in the U.S., contributing to the drilling of 600 to 1000 horizontal oil wells annually. A total of 86 per cent of the existing horizontal wells have been drilled in three formations, the Austin chalk in Texas, the Bakken shale in North Dakota, and the Niobrara in Colorado and Wyoming. A unique analytical system has been developed by the United States Department of Energy, National Petroleum Technology Office (USDOE/NPTO) to assess the potential for greater use of horizontal well technology for other oil resources in other geological formations. The analytical system is designed to be used in association with other enhanced recovery methods that make up the DOE's Total Oil Recovery Information System (TORIS). The DOE/NPTO collaborated with industry to identify the target resource for horizontal well technology and to evaluate its future recovery potential under different economic and technological conditions. This paper provides a national summary of the potential for additional production and reserves with more diverse application of horizontal wells in various types of U.S. oil resources, including the rest of the fractured reservoirs in the Austin chalk, other fractured reservoirs in the north and northwestern states, thin-bed reservoirs, and mature waterflood field. The results were presented in terms of production, reserves and national economic benefits with a full cash-flow analysis at oil prices in the range of $16 to $24 U.S. per bbl. It is estimated that 541 million to 1 billion bbls of new reserves are economically producible at these prices. The reserves estimates pertain to future horizontal wells in known fields only and are in addition to the reserves for the existing wells as of 1 January 1998. Potential production is substantial, ranging from 50 million to 85 million bbl per year by 2004 and then declining at a rate of 8 per cent per year in the following years

SFC/SFBMN guidelines update for nuclear cardiology procedures: stress testing in adults and children

International Nuclear Information System (INIS)

Manrique, A.; Marie, P.Y.; Maunoury, Ch.; Acar, Ph.; Agostini, D.

2002-01-01

The guidelines update for nuclear cardiology procedures are studied in this article. We find the minimum technique conditions for the stress testing practice, the recommendations for the different ischemia activation tests, the choice of the stress test. (N.C.)

A horizontal vane radiometer: experiment, theory and simulation

OpenAIRE

Wolfe, David; Lazarra, Andres; Garcia, Alejandro

2015-01-01

The existence of two motive forces on a Crookes radiometer has complicated the investigation of either force independently. The thermal creep shear force in particular has been subject to differing interpretations of the direction in which it acts and its order of magnitude. In this article we provide a horizontal vane radiometer design which isolates the thermal creep shear force. The horizontal vane radiometer is explored through experiment, kinetic theory, and the Direct Simulation Monte C...

Stress analysis of different prosthesis materials in implant-supported fixed dental prosthesis using 3D finite element method

Directory of Open Access Journals (Sweden)

Pedram Iranmanesh

2014-01-01

Full Text Available Introduction: In the present study, the finite element method (FEM was used to investigate the effects of prosthesis material types on stress distribution of the bone surrounding implants and to evaluate stress distribution in three-unit implant-supported fixed dental prosthesis (FDP. Materials and Methods: A three-dimensional (3D finite element FDP model of the maxillary second premolar to the second molar was designed. Three load conditions were statically applied on the functional cusps in horizontal (57.0 N, vertical (200.0 N, and oblique (400.0 N, θ = 120° directions. Four standard framework materials were evaluated: Polymethyl methacrylate (PMMA, base-metal, porcelain fused to metal, andporcelain. Results: The maximum of von Mises stress in the oblique direction was higher than the vertical and horizontal directions in all conditions. In the bone-crestal section, the maximum von Mises stress (53.78 MPa was observed in PMMA within oblique load. In FDPs, the maximum stress was generated at the connector region in all conditions. Conclusion: A noticeable difference was not observed in the bone stress distribution pattern with different prosthetic materials. Although, higher stress value could be seen in polymethyl methacrylate, all types of prosthesis yielded the same stress distribution pattern in FDP. More clinical studies are needed to evaluate the survival rate of these materials.

Method for stress determination in N, E, and T tunnels, Nevada Test Site, by hydraulic fracturing, with a comparison of overcoring methods

International Nuclear Information System (INIS)

Miller, C.H.

1976-01-01

Twenty-nine intervals in 10 core holes were hydraulically fractured in N, E, and T tunnels, Nevada Test Site, during 1974. Certain pressures were determined and related to the ambient stress field, but the orientation of the hydraulic fractures was not measured. These data and data from previous investigations in G tunnel indicated that both the magnitude of the hydraulic pressures and the direction of fracturing are independent of the orientation of the core holes. The maximum and minimum principal compressive stresses determined by the hydraulic fracturing methods are good approximations of those determined by nearby overcore methods. The data show that a good approximation of the magnitudes of the maximum and minimum principal stress axes can be obtained from several hydrofractured intervals in one core hole. Furthermore, if fracture orientation can be measured, then the direction of minimum principal compressive stress can be determined and the orientation of the plane of the maximum and intermediate principal compressive stresses can also be determined

Wake of inertial waves of a horizontal cylinder in horizontal translation

Science.gov (United States)

Machicoane, Nathanaël; Labarre, Vincent; Voisin, Bruno; Moisy, Frédéric; Cortet, Pierre-Philippe

2018-03-01

We analyze theoretically and experimentally the wake behind a horizontal cylinder of diameter d horizontally translated at constant velocity U in a fluid rotating about the vertical axis at a rate Ω . Using particle image velocimetry measurements in the rotating frame, we show that the wake is stabilized by rotation for Reynolds number Re =U d /ν much larger than in a nonrotating fluid. Over the explored range of parameters, the limit of stability is Re ≃(275 ±25 )/Ro , with Ro =U /2 Ω d the Rossby number, indicating that the stabilizing process is governed by the Ekman pumping in the boundary layer. At low Rossby number, the wake takes the form of a stationary pattern of inertial waves, similar to the wake of surface gravity waves behind a ship. We compare this steady wake pattern to a model, originally developed by Johnson [E. R. Johnson, J. Fluid Mech. 120, 359 (1982), 10.1017/S0022112082002808], assuming a free-slip boundary condition and a weak streamwise perturbation. Our measurements show quantitative agreement with this model for Ro ≲0.3 . At larger Rossby number, the phase pattern of the wake is close to the prediction for an infinitely small line object. However, the wake amplitude and phase origin are not correctly described by the weak-streamwise-perturbation model, calling for an alternative model for the boundary condition at moderate rotation rate.

HORIZONTE Y ESTRUCTURA DE LA PREGUNTA PEDAGÓGICA

Directory of Open Access Journals (Sweden)

Arturo G. Rillo

2011-01-01

Full Text Available En este artículo se abren caminos para la reflexión y la investigación de la pregunta pedagógica como un problema hermenéutico sustentado en la dialéctica de la pregunta y la respuesta. El punto de partida se construyó mediante las coordenadas propuestas por Heidegger (punto de mira, dirección de la mirada y horizonte de la mira y los prejuicios que subyacen en la tradición educativa contemporánea. El análisis se proyecta hacia la identificación de la estructura y el horizonte de la pregunta pedagógica confrontando los aportes de Heidegger, Gadamer y Freire en la elaboración de una pedagogía de la pregunta. La estructura de la pregunta incluye lo puesto en cuestión, lo preguntado y lo interrogado, lo que posibilita construir un horizonte para comprender la pregunta pedagógica desde la aproximación del estudiante a los saberes desde una praxis liberadora. Se concluye que la estructura y el horizonte de la pregunta pedagógica se sustentan en la lógica concreta del trabajo hermenéutico, donde la apertura del estudiante a las experiencias y vivencias desvela la construcción de su conocimiento mediante el arte de pensar que deriva de la praxis transformadora.

Estimation of gas wall shear stress in horizontal stratified gas-liquid pipe flow

International Nuclear Information System (INIS)

Newton, C.H.; Behnia, M.

1996-01-01

Two-phase pipe flows occur in many industrial applications, such as condensers and evaporators, chemical processing equipment, nuclear reactors, and oil pipelines. A variety of basic mechanistic flow models for predicting the pressure gradient and liquid loading characteristics of these types of flows to assist in design calculations has emerged over the past two decades, especially for the stratified and slug flow regimes. These models generally rely on a number of basic assumptions and empirical closure equations. Possibly the most notable of these relates to the evaluation of interfacial shear stresses. However, one of the most important yet least discussed assumptions used in most of these models is that the phase wall shear stresses can be accurately estimated from correlations developed for single-phase pipe flows. The object of this article is to present measurements of gas wall shear up to locations in close proximity to the gas-liquid interface for a variety of interface conditions in developed flow, and to determine the effects of the interface on average gas wall friction factors. In this context the interface may be smooth, rippled or wavy

The interconnection between biofilm formation and horizontal gene transfer

DEFF Research Database (Denmark)

Madsen, Jonas Stenløkke; Burmølle, Mette; Hansen, Lars H.

2012-01-01

Recent research has revealed that horizontal gene transfer and biofilm formation are connected processes. Although published research investigating this interconnectedness is still limited, we will review this subject in order to highlight the potential of these observations because....... Biofilms, furthermore, promote plasmid stability and may enhance the host range of mobile genetic elements that are transferred horizontally. Plasmids, on the other hand, are very well suited to promote the evolution of social traits such as biofilm formation. This, essentially, transpires because plasmids...... of their believed importance in the understanding of the adaptation and subsequent evolution of social traits in bacteria. Here, we discuss current evidence for such interconnectedness centred on plasmids. Horizontal transfer rates are typically higher in biofilm communities compared with those in planktonic states...

The Interplay of Different Types of Governance in Horizontal Cooperations

DEFF Research Database (Denmark)

Raue, Jan Simon; Wieland, Andreas

2015-01-01

Purpose – Over the last decades, horizontal cooperations between logistics service providers (LSPs) have become a well-established organizational form and their use is expected to grow even further in the future. In spite of this increasing importance of horizontal LSP cooperations, little research...

Assessment of the perception of verticality and horizontality with self-paced saccades.

Science.gov (United States)

Pettorossi, V E; Bambagioni, D; Bronstein, A M; Gresty, M A

1998-07-01

We investigated the ability of human subjects (Ss) to make self-paced saccades in the earth-vertical and horizontal directions (space-referenced task) and in the direction of the head-vertical and horizontal axis (self-referenced task) during whole body tilts of 0 degrees, 22.5 degrees, 45 degrees and 90 degrees in the frontal (roll) plane. Saccades were recorded in the dark with computerised video-oculography. During space-referenced tasks, the saccade vectors did not fully counter-rotate to compensate for larger angles of body tilt. This finding is in agreement with the 'A' effect reported for the visual vertical. The error was significantly larger for saccades intended to be space-horizontal than space-vertical. This vertico-horizontal dissociation implies greater difficulty in defining horizontality than verticality with the non-visual motor task employed. In contrast, normal Ss (and an alabyrinthine subject tested) were accurate in orienting saccades to their own (cranio-centric) vertical and horizontal axes regardless of tilt indicating that cranio-centric perception is robust and apparently not affected by gravitational influences.

Finite amplitude, horizontal motion of a load symmetrically supported between isotropic hyperelastic springs.

Science.gov (United States)

Beatty, Millard F; Young, Todd R

2012-03-01

The undamped, finite amplitude horizontal motion of a load supported symmetrically between identical incompressible, isotropic hyperelastic springs, each subjected to an initial finite uniaxial static stretch, is formulated in general terms. The small amplitude motion of the load about the deformed static state is discussed; and the periodicity of the arbitrary finite amplitude motion is established for all such elastic materials for which certain conditions on the engineering stress and the strain energy function hold. The exact solution for the finite vibration of the load is then derived for the classical neo-Hookean model. The vibrational period is obtained in terms of the complete Heuman lambda-function whose properties are well-known. Dependence of the period and hence the frequency on the physical parameters of the system is investigated and the results are displayed graphically.

12 CFR 564.4 - Minimum appraisal standards.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Minimum appraisal standards. 564.4 Section 564.4 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY APPRAISALS § 564.4 Minimum appraisal standards. For federally related transactions, all appraisals shall, at a minimum: (a...

Development of fuel assembly seismic analysis against vertical and horizontal earthquake

International Nuclear Information System (INIS)

Sato, T.; Akitake, J.; Kobayashi, H.; Azumi, S.; Koike, H.; Takeda, N.; Suzuki, S.

2001-01-01

Vertical vibration with large acceleration was observed in KOBE earthquake in 1995. Concerning PWR fuel assembly, though the vertical response has been calculated by a static analysis, it had better be calculated by a dynamic analysis in detail. Furthermore, mutual effects between horizontal and vertical motions attract our attention. For these reasons, a dynamic analysis method in the vertical direction was developed and linked with the previously developed method in the horizontal direction. This is the method that takes effect of vertical vibration into the horizontal vibration analysis as the change of horizontal stiffness, which is brought by axial compressive force. In this paper, fundamental test results for developing the method are introduced and summary of the advanced method's procedure and analysis results are also described. (authors)

The minimum wage in the Czech enterprises

OpenAIRE

Eva Lajtkepová

2010-01-01

Although the statutory minimum wage is not a new category, in the Czech Republic we encounter the definition and regulation of a minimum wage for the first time in the 1990 amendment to Act No. 65/1965 Coll., the Labour Code. The specific amount of the minimum wage and the conditions of its operation were then subsequently determined by government regulation in February 1991. Since that time, the value of minimum wage has been adjusted fifteenth times (the last increase was in January 2007). ...

Minimum Wages and Regional Disparity: An analysis on the evolution of price-adjusted minimum wages and their effects on firm profitability (Japanese)

OpenAIRE

MORIKAWA Masayuki

2013-01-01

This paper, using prefecture level panel data, empirically analyzes 1) the recent evolution of price-adjusted regional minimum wages and 2) the effects of minimum wages on firm profitability. As a result of rapid increases in minimum wages in the metropolitan areas since 2007, the regional disparity of nominal minimum wages has been widening. However, the disparity of price-adjusted minimum wages has been shrinking. According to the analysis of the effects of minimum wages on profitability us...

The model coupling fluid flow in reservoir with flow in horizontal wellbore

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiangping; Jiang, Zhixiang [RIPED-TEXACO Horizontal Well Technology Laboratory (United States)

1998-12-31

Three-dimensional pressure distributions of oil flow in a reservoir with horizontal well were derived, and a new formula to calculate pressure drop along the horizontal wellbore was developed based on the principle of conservation of matter and momentum. The formula considers the effect of influx into the horizontal wellbore from the reservoir on pressure drop in the wellbore. A mathematical model to couple fluid flow in the reservoir with flow in the horizontal wellbore is presented. Model results and experimental data showed good correspondence. Results showed the influence of pressure drop on well performance. 13 refs., 2 tabs., 7 figs.

A finite element analysis of the stress distribution to the mandible from impact forces with various orientations of third molars*

Science.gov (United States)

Liu, Yun-feng; Wang, Russell; Baur, Dale A.; Jiang, Xian-feng

2018-01-01

Objective: To investigate the stress distribution to the mandible, with and without impacted third molars (IM3s) at various orientations, resulting from a 2000-Newton impact force either from the anterior midline or from the body of the mandible. Materials and methods: A 3D mandibular virtual model from a healthy dentate patient was created and the mechanical properties of the mandible were categorized to 9 levels based on the Hounsfield unit measured from computed tomography (CT) images. Von Mises stress distributions to the mandibular angle and condylar areas from static impact forces (Load I-front blow and Load II left blow) were evaluated using finite element analysis (FEA). Six groups with IM3 were included: full horizontal bony, full vertical bony, full 450 mesioangular bony, partial horizontal bony, partial vertical, and partial 450 mesioangular bony impaction, and a baseline group with no third molars. Results: Von Mises stresses in the condyle and angle areas were higher for partially than for fully impacted third molars under both loading conditions, with partial horizontal IM3 showing the highest fracture risk. Stresses were higher on the contralateral than on the ipsilateral side. Under Load II, the angle area had the highest stress for various orientations of IM3s. The condylar region had the highest stress when IM3s were absent. Conclusions: High-impact forces are more likely to cause condylar rather than angular fracture when IM3s are missing. The risk of mandibular fracture is higher for partially than fully impacted third molars, with the angulation of impaction having little effect on facture risk. PMID:29308606

41 CFR 50-201.1101 - Minimum wages.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Minimum wages. 50-201... Contracts PUBLIC CONTRACTS, DEPARTMENT OF LABOR 201-GENERAL REGULATIONS § 50-201.1101 Minimum wages. Determinations of prevailing minimum wages or changes therein will be published in the Federal Register by the...

Condensation of steam in horizontal pipes: model development and validation

International Nuclear Information System (INIS)

Szijarto, R.

2015-01-01

This thesis submitted to the Swiss Federal Institute of Technology ETH in Zurich presents the development and validation of a model for the condensation of steam in horizontal pipes. Condensation models were introduced and developed particularly for the application in the emergency cooling system of a Gen-III+ boiling water reactor. Such an emergency cooling system consists of slightly inclined horizontal pipes, which are immersed in a cold water tank. The pipes are connected to the reactor pressure vessel. They are responsible for a fast depressurization of the reactor core in the case of accident. Condensation in horizontal pipes was investigated with both one-dimensional system codes (RELAP5) and three-dimensional computational fluid dynamics software (ANSYS FLUENT). The performance of the RELAP5 code was not sufficient for transient condensation processes. Therefore, a mechanistic model was developed and implemented. Four models were tested on the LAOKOON facility, which analysed direct contact condensation in a horizontal duct

Influence of stress on creep deformation properties of 9-12Cr ferritic creep resistant steels

Energy Technology Data Exchange (ETDEWEB)

Kimura, K.; Sawada, K.; Kushima, H. [National Institute for Materials Science (Japan)

2008-07-01

Creep deformation property of 9-12Cr ferritic creep resistant steels was investigated. With decrease in stress, a magnitude of creep strain at the onset of accelerating creep stage decreased from about 2% in the short-term to less than 1% in the longterm. A time to 1% total strain was observed in the transient creep stage in the short term regime, however, it shifted to the accelerating creep stage in the long-term regime. Life fraction of the times to 1% creep strain and 1% total strain tended to increase with decrease in stress. Difference in stress dependence of the minimum creep rate was observed in the high- and low-stress regimes with a boundary condition of 50% of 0.2% offset yield stress. Stress dependence of the minimum creep rate in the high stress regime was equivalent to a strain rate dependence of the flow stress evaluated by tensile test, and a magnitude of stress exponent, n, in the high stress regime decreased with increase in temperature from 20 at 550 C to 10 at 700 C. On the other hand, n value in the low stress regime was about 5, and creep deformation in the low stress regime was considered to be controlled by dislocation climb. Creep rupture life was accurately predicted by a region splitting method by considering a change in stress dependence of creep deformation. (orig.)

Stress and thermal expansion numerical analysis of subsea buried pipelines; Analise numerica de tensoes e expansao termica de dutos submarinos enterrados

Energy Technology Data Exchange (ETDEWEB)

Souto, Marcio de S.; Vaz, Murilo A. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia; Solano, Rafael F. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2005-07-01

The design of Capixaba North Terminal pipelines (TNC) became very complex, once the pipelines are exposed to elevated temperature variations. As the pipelines are buried, the interaction with the seabed can become critical with the thermal expansion development, since an axial compressive force arise, reaching critical values and then leading the pipeline to the thermo mechanical instability phenomenon. To minimize these effects, the pipeline will cross the shore approach through a horizontal directional drilling, and expansion loops and intermediate tie-ins took place on his route in order to permit pipeline displacements, working thermally. The objective of this present work is to develop a numerical model, able to analyze the entire pipeline stress, strain and displacements, considering different kinds of soil along of his route. The influence of expansion loops is evaluated and a comparative analysis in order to discover the minimum curvature radius at the directional drilling region is carried out. This study defines a methodology based on the developed numerical model which will be extended to future applications in subsea buried pipeline design. (author)

A test for the minimum scale of grooving on the Amatrice and Norcia earthquakes

Science.gov (United States)

Okamoto, K.; Brodsky, E. E.; Billi, A.

2017-12-01

As stress builds up along a fault, elastic strain energy builds until it cannot be accommodated by small-scale ductile deformation and then the fault brittlely fails. This brittle failure is associated with the grooving process that causes slickensides along fault planes. Therefore the scale at which slickensides disappear could be geological evidence of earthquake nucleation. Past studies found the minimum scale of grooving, however the studied fault surfaces were not exposed by recent earthquakes. These measurements could have been a product of chemical or mechanical weathering. On August 24th and October 30th of 2016, MW 6.0 and 6.5 earthquakes shook central Italy. The earthquakes caused decimeter to meter scale fault scarps along the Mt. Vettoretto Fault. Here, we analyze samples of a scarp using white light interferometry in order to determine if the minimum scale of grooving is present. Results suggest that grooving begins around 100 μm for these samples, which is consistent with previous findings of faults without any direct evidence of earthquakes. The measurement is also consistent with typical values of the frictional weakening distance Dc, which also is associated with a transition between ductile and brittle behavior. The measurements show that the minimum scale of grooving is a useful measure of the behavior of faults.

Stackelberg equilibria and horizontal differentiation

OpenAIRE

Lambertini, Luca

1993-01-01

This paper proposes a taxonomy of the Stackelberg equilibria emerging from a standard game of horizontal differentiation à la Hotelling in which the strategy set of the sellers in the location stage is the real axis. Repeated leadership appears the most advantageous position. Furthermore, this endogenously yields vertical differentiation between products at equilibrium.

HORIZONTAL LIFTING OF 5 DHLW/DOE LONG, 12-PWR LONG AND 24-BWR WASTE PACKAGES

International Nuclear Information System (INIS)

V. de la Brosse

2001-01-01

The objective of this calculation was to determine the structural response of a 12-Pressurized Water Reactor (PWR) Long, a 24-Boiling Water Reactor (BWR) and a 5-Defense High Level Waste/Department of Energy (DHLW/DOE)--Long spent nuclear fuel waste packages lifted in a horizontal position. The scope of this calculation was limited to reporting the calculation results in terms of maximum stress intensities in the trunnion collar sleeves. In addition, the maximum stress intensities in the inner and outer shells of the waste packages were presented for illustrative purposes. The information provided by the sketches (Attachments I, II and III) is that of the potential design of the types of waste packages considered in this calculation, and all obtained results are valid for these designs only. This calculation is associated with the waste package design and was performed by the Waste Package Design Section in accordance with the ''Technical work plan for: Waste Package Design Description for LA'' (Ref. 7). AP-3.12Q, Calculations (Ref. 13), was used to perform the calculation and develop the document

Minimum Wage Laws and the Distribution of Employment.

Science.gov (United States)

Lang, Kevin

The desirability of raising the minimum wage long revolved around just one question: the effect of higher minimum wages on the overall level of employment. An even more critical effect of the minimum wage rests on the composition of employment--who gets the minimum wage job. An examination of employment in eating and drinking establishments…

29 CFR 505.3 - Prevailing minimum compensation.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Prevailing minimum compensation. 505.3 Section 505.3 Labor... HUMANITIES § 505.3 Prevailing minimum compensation. (a)(1) In the absence of an alternative determination...)(2) of this section, the prevailing minimum compensation required to be paid under the Act to the...

Horizontally viscous effects in a tidal basin: extending Taylor's problem

NARCIS (Netherlands)

Roos, Pieter C.; Schuttelaars, H.M.

2009-01-01

The classical problem of Taylor (Proc. Lond. Math. Soc., vol. 20, 1921, pp. 148–181) of Kelvin wave reflection in a semi-enclosed rectangular basin of uniform depth is extended to account for horizontally viscous effects. To this end, we add horizontally viscous terms to the hydrodynamic model

Socioeconomic status, labour market connection, and self-rated psychological health: the role of social capital and economic stress.

Science.gov (United States)

Lindström, Martin; Ali, Sadiq M; Rosvall, Maria

2012-02-01

To investigate the association between socioeconomic status, unemployment and self-rated psychological health, taking economic stress and horizontal trust into account. The 2008 public health survey in Skåne is a cross-sectional postal questionnaire study with a 55% participation rate. A random sample was invited and 28,198 persons aged 18-80 participated. Logistic regression models were used to investigate associations between socioeconomic status by occupation (SES), labour market connection and self-rated psychological health (GHQ12). The multiple regression analyses included age, country of birth, education, economic stress and generalized (horizontal) trust. 13.8% of the men and 18.2% of the women had poor psychological health. Poor psychological health was more common among the young, among those born abroad, among those with lower education, with economic stress, and low horizontal trust. There were no significant differences between the employed and self-employed groups. However, the people who had retired early, the unemployed and those on long-term sick leave had significantly higher odds ratios of poor psychological health than higher non-manual employees throughout the analyses. There were no differences in psychological health between non-manual employees in higher positions and other employed and self-employed SES groups among men or women. In contrast, the early retired, the unemployed and the category on long-term sick leave had significantly higher odds ratios of poor psychological health among both men and women throughout the multiple analyses. Both economic stress and trust affected this association (i.e., lowered the odds ratios of poor psychological health), but affected by economic stress to a somewhat higher extent.

3D geomechanical modeling and numerical simulation of in-situ stress fields in shale reservoirs: A case study of the lower Cambrian Niutitang formation in the Cen'gong block, South China

Science.gov (United States)

Liu, Jingshou; Ding, Wenlong; Yang, Haimeng; Wang, Ruyue; Yin, Shuai; Li, Ang; Fu, Fuquan

2017-08-01

An analysis of the in-situ state of stress in a shale reservoir was performed based on comprehensive information about the subsurface properties from wellbores established during the development of an oil and gas field. Industrial-level shale gas production has occurred in the Niutitang formation of the lower Cambrian Cen'gong block, South China. In this study, data obtained from hydraulic fracturing, drilling-induced fractures, borehole breakout, global positioning system (GPS), and well deviation statistics have been used to determine the orientation of the maximum horizontal principal stress. Additionally, hydraulic fracturing and multi-pole array acoustic logging (XMAC) were used to determine the vertical variations in the in-situ stress magnitude. Based on logging interpretation and mechanical experiments, the spatial distributions of mechanical parameters were obtained by seismic inversion, and a 3D heterogeneous geomechanical model was established using a finite element stress analysis approach to simulate the in-situ stress fields. The effects of depth, faults, rock mechanics, and layer variations on the principal stresses, horizontal stress difference (Δσ), horizontal stress difference coefficient (Kh), and stress type coefficient (Sp) were determined. The results show that the direction of the maximum principal stress is ESE 120°. Additionally, the development zones of natural fractures appear to correlate with regions with high principal stress differences. At depths shallower than 375 m, the stress type is mainly a thrust faulting stress regime. At depths ranging from 375 to 950 m, the stress type is mainly a strike-slip faulting stress regime. When the depth is > 950 m, the stress type is mainly a normal faulting stress regime. Depth, fault orientation, and rock mechanics all affect the type of stress. The knowledge regarding the Cen'gong block is reliable and can improve borehole stability, casing set point determination, well deployment

77 FR 62396 - Annual Company-Run Stress Test Requirements for Banking Organizations With Total Consolidated...

Science.gov (United States)

2012-10-12

... minimum risk-based capital requirements.\\3\\ Stress testing is one tool that helps both bank supervisors... the FDIC and the OCC to help to ensure that the company-run stress testing regulations are consistent... purposes of the annual company-run stress tests so that the same set of scenarios can be used to conduct...

Development of fuel assembly seismic analysis against vertical and horizontal earthquake

Energy Technology Data Exchange (ETDEWEB)

Sato, T.; Akitake, J.; Kobayashi, H. [Nuclear Development Corporation, Ibaraki (Japan); Azumi, S. [Kansai Electric Power co., inc., Osaka (Japan); Koike, H.; Takeda, N.; Suzuki, S. [Kobe Shipyard and Machinery Works, Mitsubishi Heavy Industries, LTD., Kobe (Japan)

2001-07-01

Vertical vibration with large acceleration was observed in KOBE earthquake in 1995. Concerning PWR fuel assembly, though the vertical response has been calculated by a static analysis, it had better be calculated by a dynamic analysis in detail. Furthermore, mutual effects between horizontal and vertical motions attract our attention. For these reasons, a dynamic analysis method in the vertical direction was developed and linked with the previously developed method in the horizontal direction. This is the method that takes effect of vertical vibration into the horizontal vibration analysis as the change of horizontal stiffness, which is brought by axial compressive force. In this paper, fundamental test results for developing the method are introduced and summary of the advanced method's procedure and analysis results are also described. (authors)

Effect of the environment on horizontal gene transfer between bacteria and archaea.

Science.gov (United States)

Fuchsman, Clara A; Collins, Roy Eric; Rocap, Gabrielle; Brazelton, William J

2017-01-01

Horizontal gene transfer, the transfer and incorporation of genetic material between different species of organisms, has an important but poorly quantified role in the adaptation of microbes to their environment. Previous work has shown that genome size and the number of horizontally transferred genes are strongly correlated. Here we consider how genome size confuses the quantification of horizontal gene transfer because the number of genes an organism accumulates over time depends on its evolutionary history and ecological context (e.g., the nutrient regime for which it is adapted). We investigated horizontal gene transfer between archaea and bacteria by first counting reciprocal BLAST hits among 448 bacterial and 57 archaeal genomes to find shared genes. Then we used the DarkHorse algorithm, a probability-based, lineage-weighted method (Podell & Gaasterland, 2007), to identify potential horizontally transferred genes among these shared genes. By removing the effect of genome size in the bacteria, we have identified bacteria with unusually large numbers of shared genes with archaea for their genome size. Interestingly, archaea and bacteria that live in anaerobic and/or high temperature conditions are more likely to share unusually large numbers of genes. However, high salt was not found to significantly affect the numbers of shared genes. Numbers of shared (genome size-corrected, reciprocal BLAST hits) and transferred genes (identified by DarkHorse) were strongly correlated. Thus archaea and bacteria that live in anaerobic and/or high temperature conditions are more likely to share horizontally transferred genes. These horizontally transferred genes are over-represented by genes involved in energy conversion as well as the transport and metabolism of inorganic ions and amino acids. Anaerobic and thermophilic bacteria share unusually large numbers of genes with archaea. This is mainly due to horizontal gene transfer of genes from the archaea to the bacteria. In

Effect of the environment on horizontal gene transfer between bacteria and archaea

Directory of Open Access Journals (Sweden)

Clara A. Fuchsman

2017-09-01

Full Text Available Background Horizontal gene transfer, the transfer and incorporation of genetic material between different species of organisms, has an important but poorly quantified role in the adaptation of microbes to their environment. Previous work has shown that genome size and the number of horizontally transferred genes are strongly correlated. Here we consider how genome size confuses the quantification of horizontal gene transfer because the number of genes an organism accumulates over time depends on its evolutionary history and ecological context (e.g., the nutrient regime for which it is adapted. Results We investigated horizontal gene transfer between archaea and bacteria by first counting reciprocal BLAST hits among 448 bacterial and 57 archaeal genomes to find shared genes. Then we used the DarkHorse algorithm, a probability-based, lineage-weighted method (Podell & Gaasterland, 2007, to identify potential horizontally transferred genes among these shared genes. By removing the effect of genome size in the bacteria, we have identified bacteria with unusually large numbers of shared genes with archaea for their genome size. Interestingly, archaea and bacteria that live in anaerobic and/or high temperature conditions are more likely to share unusually large numbers of genes. However, high salt was not found to significantly affect the numbers of shared genes. Numbers of shared (genome size-corrected, reciprocal BLAST hits and transferred genes (identified by DarkHorse were strongly correlated. Thus archaea and bacteria that live in anaerobic and/or high temperature conditions are more likely to share horizontally transferred genes. These horizontally transferred genes are over-represented by genes involved in energy conversion as well as the transport and metabolism of inorganic ions and amino acids. Conclusions Anaerobic and thermophilic bacteria share unusually large numbers of genes with archaea. This is mainly due to horizontal gene transfer of

Selectively placing many fractures in openhole horizontal wells improves production

Energy Technology Data Exchange (ETDEWEB)

Love, T. G.; McCarty, R. A. [Chevron USA Inc (United States); Suraatmadja, J. B.; Chambers, R. W.; Grundmann, S. R.

1998-12-31

Result of a simulation of an openhole horizontal well that was treated with hydrajet fracturing, a new fracturing process wherein fractures are placed at different locations in a horizontal well without using sectional isolation techniques, are discussed. The process uses high-pressure jetting to concentrate fracturing energy at a precise fracture location, and data is obtained by means of surface and downhole pressure recorders, flow recorders, and tracers. This technique was used in a substantially depleted horizontal well in New Mexico with good results. The new process is reported to be expensive to implement which prevents widespread application at the present time. 7 refs., 9 figs.

Problems in the wellbore integrity of a shale gas horizontal well and corresponding countermeasures

Directory of Open Access Journals (Sweden)

Zhonglan Tian

2015-12-01

Full Text Available In the Changning–Weiyuan national shale gas demonstration area, SW Sichuan Basin, the wellbore integrity damage occurs in some shale gas wells and has direct effect on the gas production rate of single shale gas horizontal well. After statistics analysis was performed on the problems related with wellbore integrity, such as casing damage, casing running difficulty and cement sheath blow-by, the multi-factor coupling casing stress calculation and evaluation mode laws established. Then study was conducted on the influential mechanism of multi-factor coupling (temperature effect, casing bending and axial pressure on casing damage. The shale slip mechanism and its relationship with casing sheared formation were analyzed by using the Mohr–Coulomb criterion. Inversion analysis was performed on the main controlling factors of casing friction by using the developed casing hook load prediction and friction analysis software. And finally, based on the characteristics of shale gas horizontal wells, wellbore integrity control measures were proposed in terms of design and construction process, so as to improve the drilling quality (DQ. More specifically, shale gas well casing design calculation method and check standard were modified, well structure and full bore hole trajectory design were optimized, drilling quality was improved, cement properties were optimized and cement sealing integrity during fracturing process was checked. These research findings are significant in the design and management of future shale gas borehole integrity.

Horizontal Diplopia Following Upper Blepharoplasty

Directory of Open Access Journals (Sweden)

Tomás Ortiz-Basso

2014-09-01

Full Text Available Diplopia is an infrequent complication after blepharoplasty. Most of the cases are in its vertical form due to trauma of the extraocular muscles. In this article, we present a case of horizontal diplopia following cosmetic upper blepharoplasty; we review the literature on this unexpected complication and offer some recommendations to avoid it.

Face perception is tuned to horizontal orientation in the N170 time window.

Science.gov (United States)

Jacques, Corentin; Schiltz, Christine; Goffaux, Valerie

2014-02-07

The specificity of face perception is thought to reside both in its dramatic vulnerability to picture-plane inversion and its strong reliance on horizontally oriented image content. Here we asked when in the visual processing stream face-specific perception is tuned to horizontal information. We measured the behavioral performance and scalp event-related potentials (ERP) when participants viewed upright and inverted images of faces and cars (and natural scenes) that were phase-randomized in a narrow orientation band centered either on vertical or horizontal orientation. For faces, the magnitude of the inversion effect (IE) on behavioral discrimination performance was significantly reduced for horizontally randomized compared to vertically or nonrandomized images, confirming the importance of horizontal information for the recruitment of face-specific processing. Inversion affected the processing of nonrandomized and vertically randomized faces early, in the N170 time window. In contrast, the magnitude of the N170 IE was much smaller for horizontally randomized faces. The present research indicates that the early face-specific neural representations are preferentially tuned to horizontal information and offers new perspectives for a description of the visual information feeding face-specific perception.

Do Some Workers Have Minimum Wage Careers?

Science.gov (United States)

Carrington, William J.; Fallick, Bruce C.

2001-01-01

Most workers who begin their careers in minimum-wage jobs eventually gain more experience and move on to higher paying jobs. However, more than 8% of workers spend at least half of their first 10 working years in minimum wage jobs. Those more likely to have minimum wage careers are less educated, minorities, women with young children, and those…

Does the Minimum Wage Affect Welfare Caseloads?

Science.gov (United States)

Page, Marianne E.; Spetz, Joanne; Millar, Jane

2005-01-01

Although minimum wages are advocated as a policy that will help the poor, few studies have examined their effect on poor families. This paper uses variation in minimum wages across states and over time to estimate the impact of minimum wage legislation on welfare caseloads. We find that the elasticity of the welfare caseload with respect to the…

29 CFR 4.159 - General minimum wage.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true General minimum wage. 4.159 Section 4.159 Labor Office of... General minimum wage. The Act, in section 2(b)(1), provides generally that no contractor or subcontractor... a contract less than the minimum wage specified under section 6(a)(1) of the Fair Labor Standards...

A plant microRNA regulates the adaptation of roots to drought stress

KAUST Repository

Chen, Hao

2012-06-01

Plants tend to restrict their horizontal root proliferation in response to drought stress, an adaptive response mediated by the phytohormone abscisic acid (ABA) in antagonism with auxin through unknown mechanisms. Here, we found that stress-regulated miR393-guided cleavage of the transcripts encoding two auxin receptors, TIR1 and AFB2, was required for inhibition of lateral root growth by ABA or osmotic stress. Unlike in the control plants, the lateral root growth of seedlings expressing miR393-resistant TIR1 or AFB2 was no longer inhibited by ABA or osmotic stress. Our results indicate that miR393-mediated attenuation of auxin signaling modulates root adaptation to drought stress. © 2012 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

Horizontal gene transfer in chromalveolates

Directory of Open Access Journals (Sweden)

Bhattacharya Debashish

2007-09-01

Full Text Available Abstract Background Horizontal gene transfer (HGT, the non-genealogical transfer of genetic material between different organisms, is considered a potentially important mechanism of genome evolution in eukaryotes. Using phylogenomic analyses of expressed sequence tag (EST data generated from a clonal cell line of a free living dinoflagellate alga Karenia brevis, we investigated the impact of HGT on genome evolution in unicellular chromalveolate protists. Results We identified 16 proteins that have originated in chromalveolates through ancient HGTs before the divergence of the genera Karenia and Karlodinium and one protein that was derived through a more recent HGT. Detailed analysis of the phylogeny and distribution of identified proteins demonstrates that eight have resulted from independent HGTs in several eukaryotic lineages. Conclusion Recurring intra- and interdomain gene exchange provides an important source of genetic novelty not only in parasitic taxa as previously demonstrated but as we show here, also in free-living protists. Investigating the tempo and mode of evolution of horizontally transferred genes in protists will therefore advance our understanding of mechanisms of adaptation in eukaryotes.

A horizontal gene transfer at the origin of phenylpropanoid metabolism: a key adaptation of plants to land.

Science.gov (United States)

Emiliani, Giovanni; Fondi, Marco; Fani, Renato; Gribaldo, Simonetta

2009-02-16

The pioneering ancestor of land plants that conquered terrestrial habitats around 500 million years ago had to face dramatic stresses including UV radiation, desiccation, and microbial attack. This drove a number of adaptations, among which the emergence of the phenylpropanoid pathway was crucial, leading to essential compounds such as flavonoids and lignin. However, the origin of this specific land plant secondary metabolism has not been clarified. We have performed an extensive analysis of the taxonomic distribution and phylogeny of Phenylalanine Ammonia Lyase (PAL), which catalyses the first and essential step of the general phenylpropanoid pathway, leading from phenylalanine to p-Coumaric acid and p-Coumaroyl-CoA, the entry points of the flavonoids and lignin routes. We obtained robust evidence that the ancestor of land plants acquired a PAL via horizontal gene transfer (HGT) during symbioses with soil bacteria and fungi that are known to have established very early during the first steps of land colonization. This horizontally acquired PAL represented then the basis for further development of the phenylpropanoid pathway and plant radiation on terrestrial environments. Our results highlight a possible crucial role of HGT from soil bacteria in the path leading to land colonization by plants and their subsequent evolution. The few functional characterizations of sediment/soil bacterial PAL (production of secondary metabolites with powerful antimicrobial activity or production of pigments) suggest that the initial advantage of this horizontally acquired PAL in the ancestor of land plants might have been either defense against an already developed microbial community and/or protection against UV.

Horizontal cooperation in transport and logistics

NARCIS (Netherlands)

Cruijssen, F.C.A.M.

2006-01-01

This thesis deals with horizontal cooperation in transport and logistics. It contains a comprehensive discussion of the available academic literature on this topic, many practical examples, and an empirical investigation of opportunities and impediments. Furthermore, three enabling concepts for

Muon number violation in some horizontal gauge theories

International Nuclear Information System (INIS)

Shanker, O.

1980-11-01

Horizontal gauge models have been studied which have a mechanism for suppressing flavour changing processes involving only two flavours, i.e., processes like μ→eγ, μ→ ee anti e and the K 0 - anti K 0 transition. It is found that the rates for some muon-number violating processes, in particular for μe conversion and kaon decays, can be close to experimental upper limits. This is in contrast to horizontal gauge models in which the K 0 - anti K 0 transition is not suppressed. (auth)

The 'horizontal direct effect' of EU international agreements

DEFF Research Database (Denmark)

Gáspár-Szilágyi, Szilárd

2015-01-01

This article looks at a less discussed topic in European legal scholarship: the horizontal direct effect of EU international agreements and the Court of Justice’s apparent reluctance to expressly confirm it. It is argued that the direct effect of EU international agreements has been confirmed...... in proceedings involving private individuals/professionals against the private regulatory bodies of a profession or a State owned and controlled entity. However, direct effect has not yet been expressly confirmed in cases involving veritable horizontal relationships, between private parties of equal positions...

Gravity modulation effect on the onset of thermal buoyancy convection in a horizontal layer of the Oldroyd fluid

Energy Technology Data Exchange (ETDEWEB)

Lyubimova, Tatyana; Kovalevskaya, Kseniya, E-mail: lyubimovat@mail.ru [Institute of Continuous Media Mechanics UB RAS, Perm (Russian Federation)

2016-12-15

The effect of gravity modulation on the onset of convection in a horizontal layer of viscoelastic Oldroyd fluid heated from below is considered. The analytical solution of the problem has been obtained for the case of stress-free boundaries and rectangular modulation. It has been shown that depending on the parameter values, the modulation can produce either stabilizing or destabilizing effects. The deformation retardation always exerts a stabilizing effect, which is most pronounced in the shortwave range. The numerical results obtained by the solution of full nonlinear problems agree well with the results of linear stability analysis. (paper)

Evaluating interfacial shear stresses in composite hollo

Directory of Open Access Journals (Sweden)

Aiham Adawi

2016-09-01

Full Text Available Analytical evaluation of the interfacial shear stresses for composite hollowcore slabs with concrete topping is rare in the literature. Adawi et al. (2014 estimated the interfacial shear stiffness coefficient (ks that governs the behavior of the interface between hollowcore slabs and the concrete topping using push-off tests. This parameter is utilized in this paper to provide closed form solutions for the differential equations governing the behavior of simply supported composite hollowcore slabs. An analytical solution based on the deformation compatibility of the composite section and elastic beam theory, is developed to evaluate the shear stresses along the interface. Linear finite element modeling of the full-scale tests presented in Adawi et al. (2015 is also conducted to validate the developed analytical solution. The proposed analytical solution was found to be adequate in estimating the magnitude of horizontal shear stress in the studied composite hollowcore slabs.

Magnetoelastic shear wave propagation in pre-stressed anisotropic media under gravity

Science.gov (United States)

Kumari, Nirmala; Chattopadhyay, Amares; Singh, Abhishek K.; Sahu, Sanjeev A.

2017-03-01

The present study investigates the propagation of shear wave (horizontally polarized) in two initially stressed heterogeneous anisotropic (magnetoelastic transversely isotropic) layers in the crust overlying a transversely isotropic gravitating semi-infinite medium. Heterogeneities in both the anisotropic layers are caused due to exponential variation (case-I) and linear variation (case-II) in the elastic constants with respect to the space variable pointing positively downwards. The dispersion relations have been established in closed form using Whittaker's asymptotic expansion and were found to be in the well-agreement to the classical Love wave equations. The substantial effects of magnetoelastic coupling parameters, heterogeneity parameters, horizontal compressive initial stresses, Biot's gravity parameter, and wave number on the phase velocity of shear waves have been computed and depicted by means of a graph. As a special case, dispersion equations have been deduced when the two layers and half-space are isotropic and homogeneous. The comparative study for both cases of heterogeneity of the layers has been performed and also depicted by means of graphical illustrations.

Local versus regional active stress field in 5900m San Gregorio Magno 1 well (southern Apennines, Italy).

Science.gov (United States)

Pierdominici, S.; Montone, P.; Mariucci, M. T.

2009-04-01

The aim of this work is to characterize the local stress field in a peculiar sector of the southern Apennines by analyzing borehole breakouts, fractures and logging data along the San Gregorio Magno 1 deep well, and to compare the achieved stress field with the regional one. The study area is characterized by diffuse low-Magnitude seismicity, although in historical times it has been repeatedly struck by moderate to large earthquakes. We have analyzed in detail the 5900m San Gregorio Magno 1 well drilled in 1996-97 by ENI S.p.A. and located very close (1.3 km away) to the Irpinia Fault. This fault was responsible of the strongest earthquake happened in this area, the 23rd November 1980 M6.9 earthquake that produced the first unequivocal historical surface faulting ever documented in Italy. The mainshock enucleated on a fault 38 km-long with a strike of 308° and 60-70° northeast-dipping, consistent with a NE-SW T-axis and a normal faulting tectonic regime. Borehole breakouts, active faults and focal mechanism solutions have allowed to define the present-day stress along and around the San Gregorio Magno 1 well and other analysis (logging data) to discriminate the presence of fracture zones and/or faults at depth. We have considered data from 1200m to the bottom of San Gregorio Magno 1 well. Our analysis of stress-induced wellbore breakouts shows an inhomogeneous direction of minimum horizontal stress (N359+-31°) orientation along the well. This direction is moderately consistent with the Shmin-trend determined from breakouts in other wells in this region and also with the regional active stress field inferred from active faults and earthquake focal plane solutions (N44 Shmin oriented). For this reason we have computed for each breakout zone the difference between the local trend and the regional one; comparing these breakout rotations with the spikes or changing trend of logs we have identified possible fractures or faults at different depths. We have correlated

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures

Energy Technology Data Exchange (ETDEWEB)

Addai, Emmanuel Kwasi, E-mail: emmanueladdai41@yahoo.com; Gabel, Dieter; Krause, Ulrich

2016-04-15

Highlights: • Ignition sensitivity of a highly flammable dust decreases upon addition of inert dust. • Minimum ignition temperature of a highly flammable dust increases when inert concentration increase. • Minimum ignition energy of a highly flammable dust increases when inert concentration increase. • The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. - Abstract: The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%.

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures

International Nuclear Information System (INIS)

Addai, Emmanuel Kwasi; Gabel, Dieter; Krause, Ulrich

2016-01-01

Highlights: • Ignition sensitivity of a highly flammable dust decreases upon addition of inert dust. • Minimum ignition temperature of a highly flammable dust increases when inert concentration increase. • Minimum ignition energy of a highly flammable dust increases when inert concentration increase. • The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. - Abstract: The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%.

The use of horizontal wells for subsurface soil and aquifer remediation

International Nuclear Information System (INIS)

May, D.W.

1994-01-01

The use of directionally controlled horizontal drilling for environmental restoration had its genesis in 1988 when two horizontal remediation wells were drilled at the Savannah River Nuclear Facility near Aiken, South Carolina. Since that time, horizontal remediation wells have been drilled at several Department of Energy and Department of Defense sites as well as on several commercial sites across the country. Directional drilling technology applied to ''Near Surface Horizontal Environmental Drilling'' comes from the oil and gas industry, the utility/pipeline river crossing industry and to a lesser extent the mining industry. Rig designs vary from very small track or wheel mounted rigs using 10 feet (3 meters) drill pipe and having less than 2,500 ft. lb. (3,400 N-m) of torque and 15,000 lb. (67 kN) of push/pull force to extremely large trailer mounted rigs with torques exceeding 60,000 ft. lb. (81,400 N-m) and over 500,000 lb. (2,200 kN) of pull. Vertical depths of horizontal wells drilled to-date have exceeded 250 feet (75 m), but the great majority of contaminant plumes are located at depths of less than 50 feet (15 m). Horizontal well displacements have exceeded 1000 feet (300 m) but most of the projects cover less than 400 feet (120 m). Wells can be drilled ''blind'' (terminate in the earth) or exit back up the earth on the other side of the plume from the drill rig

Flooding characteristics of gas-liquid two-phase flow in a horizontal U bend pipe

International Nuclear Information System (INIS)

Sakaguchi, T.; Hosokawa, S.; Fujii, Y.

1995-01-01

For next-generation nuclear reactors, hybrid safety systems which consist of active and passive safety systems have been planned. Steam generators with horizontal U bend pipelines will be used as one of the passive safety systems. It is required to clarify flow characteristics, especially the onset of flooding, in the horizontal U bend pipelines in order to examine their safety. Flooding in vertical pipes has been studied extensively. However, there is little study on flooding in the horizontal U bend pipelines. It is supposed that the onset of flooding in the horizontal U bend pipelines is different from that in vertical pipes. On the other hand, liquid is generated due to condensation of steam in pipes of the horizontal steam generators at the loss of coolant accident because the steam generators will be used as a condenser of a cooling system of steam from the reactor. It is necessary to simulate this situation by the supply of water at the middle of horizontal pipe. In the present paper, experiments were carried out using a horizontal U bend pipeline with a liquid supply section in the midway of pipeline. The onset of flooding in the horizontal U bend pipeline was measured. Effects of the length of horizontal pipe and the radius of U bend on the onset of flooding were discussed

Flooding characteristics of gas-liquid two-phase flow in a horizontal U bend pipe

Energy Technology Data Exchange (ETDEWEB)

Sakaguchi, T.; Hosokawa, S.; Fujii, Y. [Kobe Univ. (Japan)] [and others

1995-09-01

For next-generation nuclear reactors, hybrid safety systems which consist of active and passive safety systems have been planned. Steam generators with horizontal U bend pipelines will be used as one of the passive safety systems. It is required to clarify flow characteristics, especially the onset of flooding, in the horizontal U bend pipelines in order to examine their safety. Flooding in vertical pipes has been studied extensively. However, there is little study on flooding in the horizontal U bend pipelines. It is supposed that the onset of flooding in the horizontal U bend pipelines is different from that in vertical pipes. On the other hand, liquid is generated due to condensation of steam in pipes of the horizontal steam generators at the loss of coolant accident because the steam generators will be used as a condenser of a cooling system of steam from the reactor. It is necessary to simulate this situation by the supply of water at the middle of horizontal pipe. In the present paper, experiments were carried out using a horizontal U bend pipeline with a liquid supply section in the midway of pipeline. The onset of flooding in the horizontal U bend pipeline was measured. Effects of the length of horizontal pipe and the radius of U bend on the onset of flooding were discussed.

Scattering phase functions of horizontally oriented hexagonal ice crystals

International Nuclear Information System (INIS)

Chen Guang; Yang Ping; Kattawar, George W.; Mishchenko, Michael I.

2006-01-01

Finite-difference time domain (FDTD) solutions are first compared with the corresponding T-matrix results for light scattering by circular cylinders with specific orientations. The FDTD method is then utilized to study the scattering properties of horizontally oriented hexagonal ice plates at two wavelengths, 0.55 and 12 μm. The phase functions of horizontally oriented ice plates deviate substantially from their counterparts obtained for randomly oriented particles. Furthermore, we compute the phase functions of horizontally oriented ice crystal columns by using the FDTD method along with two schemes for averaging over the particle orientations. It is shown that the phase functions of hexagonal ice columns with horizontal orientations are not sensitive to the rotation about the principal axes of the particles. Moreover, hexagonal ice crystals and circular cylindrical ice particles have similar optical properties, particularly, at a strongly absorbing wavelength, if the two particle geometries have the same length and aspect ratio defined as the ratio of the radius or semi-width of the cross section of a particle to its length. The phase functions for the two particle geometries are slightly different in the case of weakly absorbing plates with large aspect ratios. However, the solutions for circular cylinders agree well with their counterparts for hexagonal columns

A synopsis of environmental horizontal wells at the Savannah River Site

International Nuclear Information System (INIS)

Denham, M.E.; Lombard, K.H.

1995-01-01

Seven horizontal wells for environmental remediation were installed at the Savannah River Site as part of an Integrated Demonstration Project sponsored by the Department of Energy's Office of Technology Development. The wells were used to demonstrate innovative remediation systems for the clean up of chlorinated organic solvent contamination in groundwater and the vadose zone. The wells were installed in four demonstrations of different horizontal drilling technologies. A short-radius petroleum industry technology, a modified petroleum industry technology (using a down-hole motor), a utility industry technology, and a river crossing technology were demonstrated. The goals of the demonstrations were to show the utility of horizontal wells in environmental remediation and further development of the technology required to install these wells. From the first demonstration in 1988 to the latest in 1991, there was significant evolution in horizontal drilling technology. The main technical challenges in the first demonstration were directional control during drilling and borehole instability. Through advancement of the technology these problems were overcome and did not affect the last demonstration. Those considering the use of horizontal wells for environmental remediation will benefit from the knowledge gained from these demonstrations

Horizontal information drives the behavioural signatures of face processing

Directory of Open Access Journals (Sweden)

Valerie Goffaux

2010-09-01

Full Text Available Recent psychophysical evidence indicates that the vertical arrangement of horizontal information is particularly important for encoding facial identity. In this paper we extend this notion to examine the role that information at different (particularly cardinal orientations might play in a number of established phenomena each a behavioural “signature” of face processing. In particular we consider (a the face inversion effect (FIE, (b the facial identity after-effect, (c face-matching across viewpoint, and (d interactive, so-called holistic, processing of face parts. We report that filtering faces to remove all but the horizontal information largely preserves these effects but conversely, retaining vertical information generally diminishes or abolishes them. We conclude that preferential processing of horizontal information is a central feature of human face processing that supports many of the behavioural signatures of this critical visual operation.

The evolution of a horizontal scale for oscillatory magnetoconvection

Energy Technology Data Exchange (ETDEWEB)

Murphy, J O [Monash Univ., Clayton (Australia). Dept. of Mathematics; Lopez, J M [Aeronautical Research Labs., Port Melbourne (Australia). Aerodynamics Div.

1989-01-01

Oscillatory convective motions have been observed in the umbrae of sunspots and, in the past, the linear theory of overstability has been used for sunspot models. Here a non-linear model for oscillatory convection has been used to investigate the possibility of a preferred horizontal cell size for these motions, in the presence of a magnetic field. The integration forward in time, from the conductive state, of the non-linear multimode equations governing magnetoconvection when the magnetic Prandtl number is less than one portrays a complex interaction between the evolving magnetic and vertical velocity horizontal scales. Preferred horizontal scales for the convective cells have been established by identifying the modes that substantially contribute to the overall convective heat transport. All other modes, although initially perturbed, in time essentially decay to zero through self interaction. 8 refs., 5 figs.

The horizontal and vertical cervico-ocular reflexes of the rabbit.

Science.gov (United States)

Barmack, N H; Nastos, M A; Pettorossi, V E

1981-11-16

Horizontal and vertical cervico-ocular reflexes of the rabbit (HCOR, VCOR) were evoked by sinusoidal oscillation of the body about the vertical and longitudinal axes while the head was fixed. These reflexes were studied over a frequency range of 0.005-0.800 Hz and at stimulus amplitudes of +/- 10 degrees. When the body of the rabbit was rotated horizontally clockwise around the fixed head, clockwise conjugate eye movements were evoked. When the body was rotated about the longitudinal axis onto the right side, the right eye rotated down and the left eye rotated up. The mean gain of the HCOR (eye velocity/body velocity) rose from 0.21 and 0.005 Hz to 0.27 at 0.020 Hz and then declined to 0.06 at 0.3Hz. The gain of the VCOR was less than the gain of the HCOR by a factor of 2-3. The HCOR was measured separately and in combination with the horizontal vestibulo-ocular reflex (HVOR). These reflexes combine linearly. The relative movements of the first 3 cervical vertebrae during stimulation of the HCOR and VCOR were measured. For the HCOR, the largest angular displacement (74%) occurs between C1 and C2. For the VCOR, the largest relative angular displacement (45%) occurs between C2 and C3. Step horizontal clockwise rotation of the head and body (HVOR) evoked low velocity counterclockwise eye movements followed by fast clockwise (resetting) eye movements. Step horizontal clockwise rotation of the body about the fixed head (HCOR) evoked low velocity clockwise eye movements which were followed by fast clockwise eye movements. Step horizontal clockwise rotation of the head about the fixed body (HCOR + HVOR) evoked low velocity counterclockwise eye movements which were not interrupted by fast clockwise eye movements. These data provide further evidence for a linear combination of independent HCOR and HVOR signals.

Overview of Appalachian Basin high-angle and horizontal air and mud drilling

International Nuclear Information System (INIS)

Yost, A.B. III; Javins, B.H.

1991-01-01

The United States Department of Energy's Morgantown Energy Technology Center has been investigating the potential of using high angle and horizontal drilling technology to improve gas production from low permeability reservoirs for more than 20 years. A chronology of 45 high angle and horizontal wells have been identified to show the date, type well, type build curve, location, formation and the type of application. The historical well drilling events that have taken place since the first well are discussed to evaluate the progress in developing the technology. Detailed discussion about how the drilling technology developed in the Appalachian Basin for directional drilling and completion was provided. A discussion of the types of applications for high and horizontal drilling in the Appalachian Basin were identified. A summary of four jointly funded DOE/Industry horizontal wells were discussed to illustrate how the air horizontal drilling technology developed and learning curves for drilling cost and feet per day were provided to illustrate the improvement in the technology and equipment reliability

New Minimum Wage Research: A Symposium.

Science.gov (United States)

Ehrenberg, Ronald G.; And Others

1992-01-01

Includes "Introduction" (Ehrenberg); "Effect of the Minimum Wage [MW] on the Fast-Food Industry" (Katz, Krueger); "Using Regional Variation in Wages to Measure Effects of the Federal MW" (Card); "Do MWs Reduce Employment?" (Card); "Employment Effects of Minimum and Subminimum Wages" (Neumark,…

Exploration of horizontal intrinsic spin resonances with two partial Siberian snakes

Directory of Open Access Journals (Sweden)

F. Lin

2007-04-01

Full Text Available Two partial Siberian snakes were used to avoid all the spin imperfection and vertical intrinsic resonances in the alternating gradient synchrotron (AGS at Brookhaven National Laboratory. However, the horizontal betatron motion can cause polarization loss resulting from the nonvertical stable spin direction in the presence of two partial snakes. This type of resonance, called a horizontal intrinsic spin resonance, was observed and systematically studied in the AGS. A simplified analytic model and numerical simulation have been developed to compare with experimental data. Properties of the horizontal intrinsic resonance are discussed.

Optimal viewing position in vertically and horizontally presented Japanese words.

Science.gov (United States)

Kajii, N; Osaka, N

2000-11-01

In the present study, the optimal viewing position (OVP) phenomenon in Japanese Hiragana was investigated, with special reference to a comparison between the vertical and the horizontal meridians in the visual field. In the first experiment, word recognition scores were determined while the eyes were fixating predetermined locations in vertically and horizontally displayed words. Similar to what has been reported for Roman scripts, OVP curves, which were asymmetric with respect to the beginning of words, were observed in both conditions. However, this asymmetry was less pronounced for vertically than for horizontally displayed words. In the second experiment, the visibility of individual characters within strings was examined for the vertical and horizontal meridians. As for Roman characters, letter identification scores were better in the right than in the left visual field. However, identification scores did not differ between the upper and the lower sides of fixation along the vertical meridian. The results showed that the model proposed by Nazir, O'Regan, and Jacobs (1991) cannot entirely account for the OVP phenomenon. A model in which visual and lexical factors are combined is proposed instead.

Structural characteristics and collapse mechanism of the late Cretaceous Geumseongsan Caldera, SE Korea

Science.gov (United States)

Lee, S.; Cheon, Y.; Lee, Y.; Son, M.

2017-12-01

The Geumseongsan caldera provides an opportunity to understand the structural evolution of volcanic collapse and the role of paleostress. We focus on structural elements of the exhumed caldera floor to interpret the collapse mechanism. The caldera shows an NNW-trending elliptical shape (8×12 km). Basaltic and rhyolitic rocks are situated in the central high of the caldera, while pre-volcanic sedimentary rocks in the perimetric lowland of the volcanic rocks. Stratal attitudes change sharply from the outside to the inside of caldera bounded with a sub-vertical ring fault. The outside strata show a homocline toward SE about 15°, whereas the inside is divided into four structural domains (NE-, NW-, SE-, and SW-domains) based on the changing attitudes. The strata in NW- and SE-domains dip toward SE and NW, respectively, making an overall synclinal fold. While NE- and SW-domains comprise re-oriented, folded strata, which generally have NE- and SW-trending axes plunging toward the center. In addition, extensional and contractional structures occur distinctively in NW- and SE-domains and in NE- and SW-domains, respectively, indicating an axisymmetric deformation around NE-SW axis. The results indicate that higher horizontal mass movement toward the center occurred in NW- and SE-domains than in NE- and SW-domains while vertical mass movement was more active in the latter. This axisymmetric deformation could be produced by regional stress during the volcanic activity, which affected the collapse pattern of caldera floor. The regional stress field during the late Cretaceous is known as NW-SE horizontal maximum and NE-SW horizontal minimum stresses due to the oblique subduction of proto-Pacific Plate underneath Eurasian Plate. NNW-trending elliptical shape of the caldera is interpreted to have formed under the influence of this stresses, like a tension gash. The NW-SE maximum stress possibly acted to resist vertical displacement along the marginal fault of NW- and SE

Teaching the Minimum Wage in Econ 101 in Light of the New Economics of the Minimum Wage.

Science.gov (United States)

Krueger, Alan B.

2001-01-01

Argues that the recent controversy over the effect of the minimum wage on employment offers an opportunity for teaching introductory economics. Examines eight textbooks to determine topic coverage but finds little consensus. Describes how minimum wage effects should be taught. (RLH)

Vertical and horizontal control dilemmas in public hospitals.

Science.gov (United States)

Pettersen, Inger Johanne; Solstad, Elsa

2015-01-01

The hospital sector in Norway has been continuously reorganized since 2002 and the reforms have created organizations that are functionally/vertically controlled, whereas the production lines are coordinated on a process or a lateral basis. The purpose of this paper is to focus on both the perceived functional vertical control and horizontal controls within and between the local hospitals and the regional administrative levels. A national survey study, complemented with interviews of some key informants and document studies. The study shows that the functional and vertical lines of management control are perceived to be operating according to the traditional views of management control. The study indicates that the horizontal tasks are not very well implemented, and we did not find interactive and lateral uses of management control systems for managerial purposes. New control problems arise when services are to be coordinated between autonomous units. The paper focuses on the control problems found within the horizontal, flat relationship between production units in hospitals; new organizational structures have emerged where lateral relations are important, but traditional control practices follow functional, vertical lines.

Influence of physical characteristics and ingredients on the minimum burning pressure of ammonium nitrate emulsions

Energy Technology Data Exchange (ETDEWEB)

Turcotte, R.; Goldthorp, S.; Badeen, C.M.; Johnson, C.; Feng, H. [Natural Resources Canada, Ottawa, ON (Canada). Canadian Explosives Research Laboratory; Chan, S.K. [Orica Canada Inc., Brownsburg-Chatham, PQ (Canada)

2009-05-15

The sustained combustion of ammonium nitrate water-based explosives (AWEs) will not occur when pressures are kept below specific threshold values. The minimum burning pressure (MBP) is used to estimate safety operating pressures for the processing, manufacturing and handling of AWEs. MBP measurements were performed for various commercially available AWEs. The purpose of the study was to determine how common formulation changes may affect the MBP of AWEs and how changes in testing methodologies will influence obtained MBP values. The study examined how the testing geometries of products containing glass microspheres altered the combustion behaviour of the AWEs used in the test. The influence of temperature and initial viscosity on the MBP was also investigated. The study showed that re-solidified glass was found in the bottom cap of the cell during vertical testing geometries. It was concluded that slow decomposition events were eliminated when using a horizontal testing geometry. 12 refs., 8 figs.

Flow mapping for ESS horizontal target

Energy Technology Data Exchange (ETDEWEB)

Takeda, Y.; Kikura, H.; Taishi, T. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-09-01

Flow behaviour for ESS horizontal target is studied experimentally using two dimensional water model. A velocity field of stationary flow in reaction zone has been obtained. Three dimensional effect was also studied as a spanwise flow structure. (author) 3 figs., 3 refs.

30 CFR 75.1431 - Minimum rope strength.

Science.gov (United States)

2010-07-01

..., including rotation resistant). For rope lengths less than 3,000 feet: Minimum Value=Static Load×(7.0−0.001L) For rope lengths 3,000 feet or greater: Minimum Value=Static Load×4.0 (b) Friction drum ropes. For rope lengths less than 4,000 feet: Minimum Value=Static Load×(7.0−0.0005L) For rope lengths 4,000 feet...

Prediction of Heat Removal Capacity of Horizontal Condensation Heat Exchanger submerged in Pool

Energy Technology Data Exchange (ETDEWEB)

Jeon, Seong-Su; Hong, Soon-Joon [FNC Tech., Yongin (Korea, Republic of); Cho, Hyoung-Kyu [Seoul National University, Seoul (Korea, Republic of); Park, Goon-Cherl [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2014-10-15

As representative passive safety systems, there are the passive containment cooling system (PCCS) of ESBWR, the emergency condenser system (ECS) of the SWR-1000, the passive auxiliary feed-water system (PAFS) of the APR+ and etc. During the nuclear power plant accidents, these passive safety systems can cool the nuclear system effectively via the heat transfer through the steam condensation, and then mitigate the accidents. For the optimum design and the safety analysis of the passive safety system, it is essential to predict the heat removal capacity of the heat exchanger well. The heat removal capacity of the horizontal condensation heat exchanger submerged in a pool is determined by a combination of a horizontal in-tube condensation heat transfer and a boiling heat transfer on the horizontal tube. Since most correlations proposed in the previous nuclear engineering field were developed for the vertical tube, there is a certain limit to apply these correlations to the horizontal tube. Therefore, this study developed the heat transfer model for the horizontal Ushaped condensation heat exchanger submerged in a pool to predict well the horizontal in-tube condensation heat transfer, the boiling heat transfer on the horizontal tube and the overall heat removal capacity of the heat exchanger using the best-estimate system analysis code, MARS.

Sprint Acceleration Mechanics: The Major Role of Hamstrings in Horizontal Force Production

Science.gov (United States)

Morin, Jean-Benoît; Gimenez, Philippe; Edouard, Pascal; Arnal, Pierrick; Jiménez-Reyes, Pedro; Samozino, Pierre; Brughelli, Matt; Mendiguchia, Jurdan

2015-01-01

Recent literature supports the importance of horizontal ground reaction force (GRF) production for sprint acceleration performance. Modeling and clinical studies have shown that the hip extensors are very likely contributors to sprint acceleration performance. We experimentally tested the role of the hip extensors in horizontal GRF production during short, maximal, treadmill sprint accelerations. Torque capabilities of the knee and hip extensors and flexors were assessed using an isokinetic dynamometer in 14 males familiar with sprint running. Then, during 6-s sprints on an instrumented motorized treadmill, horizontal and vertical GRF were synchronized with electromyographic (EMG) activity of the vastus lateralis, rectus femoris, biceps femoris, and gluteus maximus averaged over the first half of support, entire support, entire swing and end-of-swing phases. No significant correlations were found between isokinetic or EMG variables and horizontal GRF. Multiple linear regression analysis showed a significant relationship (P = 0.024) between horizontal GRF and the combination of biceps femoris EMG activity during the end of the swing and the knee flexors eccentric peak torque. In conclusion, subjects who produced the greatest amount of horizontal force were both able to highly activate their hamstring muscles just before ground contact and present high eccentric hamstring peak torque capability. PMID:26733889

Sprint acceleration mechanics: the major role of hamstrings in horizontal force production

Directory of Open Access Journals (Sweden)

Jean-Benoit eMORIN

2015-12-01

Full Text Available Recent literature supports the importance of horizontal ground reaction force (GRF production for sprint acceleration performance. Modeling and clinical studies have shown that the hip extensors are very likely contributors to sprint acceleration performance. We experimentally tested the role of the hip extensors in horizontal GRF production during short, maximal, treadmill sprint accelerations. Torque capabilities of the knee and hip extensors and flexors were assessed using an isokinetic dynamometer in 14 males familiar with sprint running. Then, during 6-s sprints on an instrumented motorized treadmill, horizontal and vertical GRF were synchronized with electromyographic (EMG activity of the vastus lateralis, rectus femoris, biceps femoris and gluteus maximus averaged over the first half of support, entire support, entire swing and end-of-swing phases. No significant correlations were found between isokinetic or EMG variables and horizontal GRF. Multiple linear regression analysis showed a significant relationship (P = 0.024 between horizontal GRF and the combination of biceps femoris EMG activity during the end of the swing and the knee flexors eccentric peak torque. In conclusion, subjects who produced the greatest amount of horizontal force were both able to highly activate their hamstring muscles just before ground contact and present high eccentric hamstring peak torque capability.

Transmission of vertical soil stress under agricultural tyres

DEFF Research Database (Denmark)

Keller, Thomas; Berli, M.; Ruiz, S.

2014-01-01

and simulate soil stress under defined loads. Stress in the soil profile at 0.3, 0.5 and 0.7 m depth was measured during wheeling at a water content close to field capacity on five soils (13–66% clay). Stress transmission was then simulated with a semi-analytical model, using vertical stress at 0.1 m depth......The transmission of stress induced by agricultural machinery within an agricultural soil is typically modelled on the basis of the theory of stress transmission in elastic media, usually in the semi-empirical form that includes the “concentration factor” (v). The aim of this paper was to measure...... estimated from tyre characteristics as the upper boundary condition, and v was obtained at minimum deviation between measurements and simulations. For the five soils, we obtained an average v of 3.5 (for stress transmitting from 0.1 to 0.7 m depth). This was only slightly different from v = 3 for which...

Oriented cluster perforating technology and its application in horizontal wells

Directory of Open Access Journals (Sweden)

Huabin Chen

2016-11-01

Full Text Available An oriented cluster perforating technology, which integrates both advantages of cluster and oriented perforating, will help solve a series of technical complexities in horizontal well drilling. For realizing its better application in oil and gas development, a series of technologies were developed including perforator self-weight eccentricity, matching of the electronic selective module codes with the surface program control, axial centralized contact signal transmission, and post-perforation intercluster sealing insulation. In this way, the following functions could be realized, such as cable-transmission horizontal well perforator self-weight orientation, dynamic signal transmission, reliable addressing & selective perforation and post-perforation intercluster sealing. The combined perforation and bridge plug or the multi-cluster perforation can be fulfilled in one trip of perforation string. As a result, the horizontal-well oriented cluster perforating technology based on cable conveying was developed. This technology was successfully applied in unconventional gas reservoir exploitation, such as shale gas and coalbed methane, with accurate orientation, reliable selective perforation and satisfactory inter-cluster sealing. The horizontal-well oriented cluster perforating technology benefits the orientation of horizontal well drilling with a definite target and direction, which provides a powerful support for the subsequent reservoir stimulation. It also promotes the fracturing fluid to sweep the principal pay zones to the maximum extent. Moreover, it is conductive to the formation of complex fracture networks in the reservoirs, making quality and efficient development of unconventional gas reservoirs possible.

Natural convection in horizontal fluid layers

International Nuclear Information System (INIS)

Suo-Antilla, A.J.

1977-02-01

The experimental work includes developing and using a thermal convection cell to obtain measurements of the heat flux and turbulent core temperature of a horizontal layer of fluid heated internally and subject to both stabilizing and destabilizing temperature differences. The ranges of Rayleigh numbers tested were 10 7 equal to or less than R/sub I/ equal to or less than 10 13 and -10 10 equal to or less than R/sub E/ equal to or less than 10 10 . Power integral methods were found to be adequate for interpolating and extrapolating the data. The theoretical work consists of the derivation, solution and use of the mean field equations for study of thermally driven convection in horizontal layers of infinite extent. The equations were derived by a separation of variables technique where the horizontal directions were described by periodic structures and the vertical being some function of z. The derivation resulted in a coupled set of momentum and energy equations. The equations were simplified by using the infinite Prandtl number limit and neglecting direct intermodal interaction. Solutions to these equations are used to predict the existence of multi-wavenumber flows at all supercritical Rayleigh numbers. Subsequent inspection of existing experimental photographs of convecting fluids confirms their existence. The onset of time dependence is found to coincide with the onset of the second convective mode. Each mode is found to consist of two wavenumbers and typically the velocity and temperature fields of the right modal branch are found to be out of phase

Deformation of the southeast part of the Columbia Plateau

International Nuclear Information System (INIS)

Hooper, P.R.; Camp, V.E.

1981-01-01

Four structural elements north of the Olympic-Wallowa lineament in the southeast part of the Columbia Plateau (Washington, Idaho, and Oregon) are (1) the offlap of progressively younger basalt units from prebasalt topographic highs; (2) east-west open folds associated with reverse faulting; (3) northwest-southeast, northeast-southwest, and north-south faults with predominantly vertical displacement; and (4) vertical north-northwest-south-southeast feeder dikes. These may be explained by (1) a regional east to west tilting of the plateau caused by the isostatic rise of older rocks on the eastern margin; (2) a stress regime with a horizontal maximum principal stress in a north-northwest-south-southeast direction, and a horizontal minimum principal stress in a west-southwest-east-northeast direction; and (3) reactivation of an older northwest-southeast, northeast-southwest, and north-south structural grain in the pre-Miocene basement. The stress regime is similar to that envisaged for the area southwest of the Olympic-Wallowa lineament, and the difference in the type of deformation on either side of that feature may be attributed to differences in the thickness of the crust across the ancient boundary

Fracture criteria of reactor graphite under multiaxial stresses

International Nuclear Information System (INIS)

Sato, S.; Kawamata, K.; Kurumada, A.; Oku, T.

1987-01-01

New fracture criteria for graphite under multiaxial stresses are presented for designing core and support materials of a high temperature gas cooled reactor. Different kinds of fracture strength tests are carried out for a near isotropic graphite IG-11. Results show that, under the stress state in which tensile stresses are predominant, the maximum principal stress theory is seen as applicable for brittle fracture. Under the stress state in which compressive stresses are predominant there may be two fracture modes for brittle fracture, namely, slipping fracture and mode II fracture. For the former fracture mode the maximum shear stress criterion is suitable, but for the latter fracture mode a new mode II fracture criterion including a restraint effect for cracks is verified to be applicable. Also a statistical correction for brittle fracture criteria under multiaxial stresses is discussed. By considering the allowable stress values for safe design, the specified minimum ultimate strengths corresponding to a survival probability of 99% at the 95% confidence level are presented. (orig./HP)

Tendência da mortalidade perinatal em Belo Horizonte, 1984 a 2005 Tendencia de la mortalidad perinatal en Belo Horizonte, 1984 a 2005 Tendency of perinatal mortality in Belo Horizonte, 1984 to 2005

Directory of Open Access Journals (Sweden)

Eunice Francisca Martins

2010-06-01

Full Text Available O estudo objetivou analisar a tendência da mortalidade perinatal no município de Belo Horizonte no período de 1984 a 2005. A fonte dos dados foi o Sistema de Informação de Mortalidade (SIM. Realizou-se regressão linear simples para estimar a tendência de redução do percentual de informações ignoradas no SIM e das taxas de mortalidade. A melhora da qualidade da informação foi estatisticamente significativa apenas para a escolaridade materna e peso ao nascer. A redução média da mortalidade perinatal no período foi de 57,52%. O decréscimo da mortalidade perinatal nas duas últimas décadas em Belo Horizonte foi significativo, mas esforços devem ser direcionados no sentido de melhorar a completude do SIM para variáveis importantes na elaboração dos indicadores perinatais.El estudio apuntó a analizar la tendencia de la mortalidad perinatal en el distrito municipal de Belo Horizonte en el periodo de 1984 a 2005. La fuente de los datos era el Sistema de Información de Mortalidad. Tuvieron lugar la regresión lineal simple para estimar la tendencia de reducción del percentil de información desconocida en el sistema y de los impuestos de mortalidad. La mejora de la calidad de la información fue los significantes sólo para la educación maternal y peso al nacer. La reducción elemento de la mortalidad perinatal en el periodo era de 57,52%. La disminución de la mortalidad perinatal en las últimas dos décadas en Belo Horizonte era significante, pero deben dirigirse los esfuerzos en el sentido de mejorar el completude del sistema para las variables importantes en la elaboración del perinatais de los indicadores.The study aimed at to analyze the tendency of the mortality perinatal in the municipal district of Belo Horizonte in the period from 1984 to 2005. The source of the data was the System of Information of Mortality. Took place simple lineal regression to esteem the tendency of reduction of the percentile of unknown

The Alignment of the Mean Wind and Stress Vectors in the Unstable Surface Layer

Science.gov (United States)

Bernardes, M.; Dias, N. L.

2010-01-01

A significant non-alignment between the mean horizontal wind vector and the stress vector was observed for turbulence measurements both above the water surface of a large lake, and over a land surface (soybean crop). Possible causes for this discrepancy such as flow distortion, averaging times and the procedure used for extracting the turbulent fluctuations (low-pass filtering and filter widths etc.), were dismissed after a detailed analysis. Minimum averaging times always less than 30 min were established by calculating ogives, and error bounds for the turbulent stresses were derived with three different approaches, based on integral time scales (first-crossing and lag-window estimates) and on a bootstrap technique. It was found that the mean absolute value of the angle between the mean wind and stress vectors is highly related to atmospheric stability, with the non-alignment increasing distinctively with increasing instability. Given a coordinate rotation that aligns the mean wind with the x direction, this behaviour can be explained by the growth of the relative error of the u- w component with instability. As a result, under more unstable conditions the u- w and the v- w components become of the same order of magnitude, and the local stress vector gives the impression of being non-aligned with the mean wind vector. The relative error of the v- w component is large enough to make it undistinguishable from zero throughout the range of stabilities. Therefore, the standard assumptions of Monin-Obukhov similarity theory hold: it is fair to assume that the v- w stress component is actually zero, and that the non-alignment is a purely statistical effect. An analysis of the dimensionless budgets of the u- w and the v- w components confirms this interpretation, with both shear and buoyant production of u- w decreasing with increasing instability. In the v- w budget, shear production is zero by definition, while buoyancy displays very low-intensity fluctuations around

Analytical solution of velocity for ammonia-water horizontal falling-film flow

International Nuclear Information System (INIS)

Zhang, Qiang; Gao, Yide

2016-01-01

Highlights: • We built a new falling-film flow model that analyzed the film flow characteristics. • We have obtained a new formula of film thickness over the horizontal tube. • We derived analysis solution to analyze the effect of inertial force to velocity in the entrance region of liquid film. • It described the characters of the ammonia-waterfalling-film film over the horizontal tube. • It is good for falling-film absorption, generation and evaporation to optimizing the design parameters and further improving the capabilities. - Abstract: A new horizontal tube falling film velocity model was built and calculated to analyze the problem of film flow conditions. This model also analyzed the film thickness distribution in horizontal tube falling film flow and considered the effect of the inertial force on velocity. The film thickness and velocity profile can be obtained based on the principle of linear superposition, a method of separation of variables that introduces the effect of variable inertial force on the velocity profile in the process of falling-film absorption. The film flow condition and the film thickness distribution at different fluid Reynolds numbers (Re) and tube diameters were calculated and compared with the results of the Crank–Nicolson numerical solution under the same conditions. The results show that the film flow condition out of a horizontal tube and that the film thickness increases with the fluid Re. At a specific Re and suitable tube diameter, the horizontal tube reaches a more uniform film. Finally, the analysis results have similar trend with the experimental and numerical predicted data in literature.

Buoyancy Driven Natural Ventilation through Horizontal Openings

DEFF Research Database (Denmark)

Heiselberg, Per; Li, Zhigang

2009-01-01

An experimental study of the phenomenon of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. The measurements were made for opening ratios L/D ranging from 0.027 to 4.455, where L and D are the length of the opening...... and the diameter of the opening, respectively. The basic nature of airflow through single-sided openings, including airflow rate, air velocity, temperature difference between the rooms and the dimensions of the horizontal openings, were measured. A bi-directional airflow rate was measured using the constant...... quite well with the Epstein's formula but in other cases the measured data show clear deviations from the Epstein's formula. Thus, revised formulas for natural ventilation are proposed....

Conservative management of displaced horizontal root fracture

Directory of Open Access Journals (Sweden)

Sanjeev Kunhappan

2011-01-01

Full Text Available Traumatic injuries of teeth are the main cause of emergency treatment in dental practice. Radicular fractures in permanent teeth are uncommon, being only 0.5-7% of the cases. Horizontal root fractures are more frequently observed in the maxillary anterior region of young male patients and vary in severity from enamel fractures to avulsions. Fracture occurs often in the middle-third of the root followed by apical and coronal third. The present case report describes a clinical case of a horizontal root fracture located at the middle third of a maxillary left-central incisor treated endodontically after approximating fracture segment with the help of orthodontic appliance. After 6 months follow-up, the tooth was asymptomatic with normal periodontal health.

Effects of cross-anisotropy and stress-dependency of pavement layers on pavement responses under dynamic truck loading

Directory of Open Access Journals (Sweden)

Rafiqul A. Tarefder

2016-06-01

Full Text Available Previous studies by the authors have determined pavement responses under dynamic loading considering cross-anisotropy in one layer only, either the cross-anisotropic viscoelastic asphalt concrete (AC layer or the cross-anisotropic stress-dependent base layer, but not both. This study evaluates pavement stress–strain responses considering cross-anisotropy in all layers, i.e. AC, base and subbase, using finite element modeling (FEM technique. An instrumented pavement section on Interstate I-40 near Albuquerque, New Mexico was used in ABAQUS framework as model geometry. Field asphalt cores were collected and tested in the laboratory to determine the cross-anisotropy (n-values defined by horizontal to vertical modulus ratio, and other viscoelastic parameters as inputs of the model incorporated through user defined material interface (UMAT functionality in ABAQUS. Field base and subbase materials were also collected and tested in the laboratory to determine stress-dependent nonlinear elastic model parameters, as inputs of the model, again incorporated through UMAT. The model validation task was carried out using field-measured deflections and strain values under falling weight deflectometer (FWD loads at the instrumented section. The validated model was then subjected to an actual truck loading for studying cross-anisotropic effects. It was observed that horizontal tensile strain at the bottom of the AC layer and vertical strains in all layers decreased with an increase in n-value of the asphalt layer, from n < 1 (anisotropy to n=1 (isotropy. This indicates that the increase in horizontal modulus caused the decrease in layer strains. It was also observed that if the base and subbase layers were considered stress-dependent instead of linear elastic unbound layers, the horizontal tensile strain at the bottom of the asphalt layer increased and vertical strains on top of the base and subbase also increased.

30 CFR 281.30 - Minimum royalty.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Minimum royalty. 281.30 Section 281.30 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER THAN OIL, GAS, AND SULPHUR IN THE OUTER CONTINENTAL SHELF Financial Considerations § 281.30 Minimum royalty...

Identification of natural fractures and in situ stress at Rantau Dedap geothermal field

Science.gov (United States)

Artyanto, Andika; Sapiie, Benyamin; Idham Abdullah, Chalid; Permana Sidik, Ridwan

2017-12-01

Rantau Dedap Area is a geothermal field which is located in Great Sumatra Fault (GSF). The fault and fracture are main factor in the permeability of the geothermal system. However, not all faults and fractures have capability of to flow the fluids. Borehole image log is depiction of the borehole conditions, it is used to identify the natural fractures and drilling induced fracture. Both of them are used to identify the direction of the fracture, direction of maximum horizontal stress (SHmax), and geomechanics parameters. The natural fractures are the results of responses to stress on a rock and permeability which controlling factor in research area. Breakouts is found in this field as a trace of drilling induced fracture due to in situ stress work. Natural fractures are strongly clustered with true strike trending which first, second, and third major direction are N170°E - N180°E (N-S), N60°E - N70°E (NE-SW), and N310°E - N320°E (NW-SE), while the dominant dip is 80° -90°. Based on borehole breakout analysis, maximum horizontal stress orientation is identified in N162°E - N204°E (N-S) and N242°E (NE-SW) direction. It’s constantly similar with regional stress which is affected by GSF. Several parameters have been identified and analyzed are SHmax, SHmin, and Sy. It can be concluded that Rantau Dedap Geothermal Field is affected by strike-slip regime. The determination of in situ stress and natural fractures are important to study the pattern of permeability which is related to the fault in reservoir of this field.

Horizontal and Vertical Cultural Differences in the Content of Advertising Appeals.

Science.gov (United States)

Shavitt, Sharon; Johnson, Timothy P; Zhang, Jing

2011-05-01

The distinction between vertical (emphasizing hierarchy) and horizontal (valuing equality) cultures yields novel predictions regarding the prevalence of advertising appeals. A content analysis of 1211 magazine advertisements in five countries (Denmark, Korea, Poland, Russia, U.S.) revealed differences in ad content that underscore the value of this distinction. Patterns in the degree to which ads emphasized status benefits and uniqueness benefits corresponded to the countries' vertical/horizontal cultural classification. These and other patterns of ad benefits are analyzed and the predictions afforded by the vertical/horizontal distinction versus the broader individualism-collectivism distinction are compared and tested.

Stress evolution and fault stability during the Weichselian glacial cycle

Energy Technology Data Exchange (ETDEWEB)

Lund, Bjoern; Schmidt, Peter; Hieronymus, Christoph (Dept. of Earth Sciences, Uppsala Univ., Uppsala (Sweden))

2009-10-15

In this report we examine how the waxing and waning of an ice sheet during a glacial cycle affects the state of stress in the Earth, and how those changes in stress influence the stability of faults. We focus on the stresses at repository depth in Forsmark and Oskarshamn, and on the stability field at seismogenic depth at the proposed repository sites and at the Paervie endglacial fault in northern Sweden. This study is a modelling study, where we use 3-dimensional ice and earth models to calculate the glacial isostatic adjustment (GIA), i.e. the response of the Earth to an ice load, examining both displacements and stresses. We use a flat-earth finite element approach, based on Wu with some modifications. The result presented here is a continuation of previous studies in 2 dimensions and complement those studies in assessing how the 3-dimensionality of the problem affects the conclusions. We use the Fennoscandian ice model of Naeslund, which is a dynamic ice sheet model based on climate reconstructions with constraints from geological observations. The ice model spans the entire Weichselian glaciation but we only use the last 68 kyr, which includes the 2 major periods of ice cover as depicted in this ice sheet reconstruction. For the GIA calculation we use a number of different earth models, both with flat horizontal layers and with various 3D structures of lithosphere thickness. We don't include lateral variations in the viscosity of the mantle. Comparing the current day rebound velocities predicted by our models with GPS observations from the BIFROST project, we note that in general, we can obtain a reasonable fit to the observations with our models, and that the results are rather sensitive to the assumed viscosity of the mantle. We find that the differences between data and model results, for all earth models, have common features which we interpret as due to the ice model. These observations are in agreement with numerous other GIA studies. Our flat

Stress state and its anomaly observations in the vicinity of a fault in NanTroSEIZE Expedition 322

Science.gov (United States)

Wu, Hung-Yu; Saito, Saneatsu; Kinoshita, Masataka

2015-12-01

To better understand the stress state and geological properties within the shallow Shikoku Basin, southwest of Japan, two sites, C0011A and C0011B, were drilled in open-ocean sediments using Logging While Drilling (LWD) and coring, respectively. Resistivity image logging was performed at C0011A from sea floor to 950 m below sea floor (mbsf). At C0011B, the serial coring was obtained in order to determine physical properties from 340 to 880 mbsf. For the LWD images, a notable breakout anomaly was observed at a depth of 615 m. Using resistivity images and a stress polygon, the potential horizontal principal stress azimuth and its magnitude within the 500-750 mbsf section of the C0011A borehole were constrained. Borehole breakout azimuths were observed for the variation by the existence of a fault zone at a depth of 615 mbsf. Out of this fracture zone, the breakout azimuth was located at approximately 109° ± 12°, subparallel to the Nankai Trough convergence vector (300-315°). Our calculations describe a stress drop was determined based on the fracture geometry. A close 90° (73° ± 12°) rotation implied a 100% stress drop, defined as a maximum shear stress drop equal to 1 MPa. The magnitude of the horizontal principal stresses near the fracture stress anomaly ranged between 49 and 52 MPa, and the bearing to the vertical stress (Sv = 52 MPa) was found to be within the normal-faulting stress regime. Low rock strength and a low stress level are necessary to satisfy the observations.

Horizontal inequality in education and wealth in Tanzania: A 20-year perspective

OpenAIRE

Maliti, Emmanuel

2016-01-01

This study uses five series of demographic and health surveys to answer the question: 'Is horizontal inequality in education and wealth increasing or decreasing in the 20-year interval between 1991 and 2010?'. Horizontal inequality in education attainment has been moving in waves; however, there was an invested U-shaped trend where inequality increased between 2004 and 2007 before a declining trend in recent years. Unlike the fluctuating trends of the overall horizontal inequality in educatio...

State cigarette minimum price laws - United States, 2009.

Science.gov (United States)

2010-04-09

Cigarette price increases reduce the demand for cigarettes and thereby reduce smoking prevalence, cigarette consumption, and youth initiation of smoking. Excise tax increases are the most effective government intervention to increase the price of cigarettes, but cigarette manufacturers use trade discounts, coupons, and other promotions to counteract the effects of these tax increases and appeal to price-sensitive smokers. State cigarette minimum price laws, initiated by states in the 1940s and 1950s to protect tobacco retailers from predatory business practices, typically require a minimum percentage markup to be added to the wholesale and/or retail price. If a statute prohibits trade discounts from the minimum price calculation, these laws have the potential to counteract discounting by cigarette manufacturers. To assess the status of cigarette minimum price laws in the United States, CDC surveyed state statutes and identified those states with minimum price laws in effect as of December 31, 2009. This report summarizes the results of that survey, which determined that 25 states had minimum price laws for cigarettes (median wholesale markup: 4.00%; median retail markup: 8.00%), and seven of those states also expressly prohibited the use of trade discounts in the minimum retail price calculation. Minimum price laws can help prevent trade discounting from eroding the positive effects of state excise tax increases and higher cigarette prices on public health.

Performance of a Horizontal Triple Cylinder Type Pulping Machine

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2011-05-01

Full Text Available Pulping is one important step in wet coffee processing method. Pulping process usually uses a machine which constructed by wood or metal materials. A horizontal single cylinder type of fresh coffee cherries pulping machine is the most popular machine in coffee processing. One of the weaknesses of a horizontal single cylinder type of fresh coffee cherries pulping machine is higher in broken beans. Broken bean is one of mayor aspects in defect system that contribute to low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type of fresh coffee cherries pulping machine which resulted in 12.6—21.4% of broken beans. To reduce percentage of broken beans, Indonesian Coffee and Cocoa Research Institute has developed and tested a horizontal triple cylinder type of fresh coffee cherries pulping machine. Material tested was fresh mature Robusta coffee cherries, 60—65% (wet basis moisture content; has classified on 3 levels i.e. unsorted, small and medium, and clean from metal and foreign materials. The result showed that the machine produced 6,340 kg/h in optimal capacity for operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 55.5% whole parchment coffee, 3.66% broken beans, and 1% beans in wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

Guided Growth of Horizontal p-Type ZnTe Nanowires

Science.gov (United States)

2016-01-01

A major challenge toward large-scale integration of nanowires is the control over their alignment and position. A possible solution to this challenge is the guided growth process, which enables the synthesis of well-aligned horizontal nanowires that grow according to specific epitaxial or graphoepitaxial relations with the substrate. However, the guided growth of horizontal nanowires was demonstrated for a limited number of materials, most of which exhibit unintentional n-type behavior. Here we demonstrate the vapor–liquid–solid growth of guided horizontal ZnTe nanowires and nanowalls displaying p-type behavior on four different planes of sapphire. The growth directions of the nanowires are determined by epitaxial relations between the nanowires and the substrate or by a graphoepitaxial effect that guides their growth along nanogrooves or nanosteps along the surface. We characterized the crystallographic orientations and elemental composition of the nanowires using transmission electron microscopy and photoluminescence. The optoelectronic and electronic properties of the nanowires were studied by fabricating photodetectors and top-gate thin film transistors. These measurements showed that the guided ZnTe nanowires are p-type semiconductors and are photoconductive in the visible range. The guided growth of horizontal p-type nanowires opens up the possibility of parallel nanowire integration into functional systems with a variety of potential applications not available by other means. PMID:27885331

A review on critical heat flux in horizontal tubes

International Nuclear Information System (INIS)

Baburajan, P.K.; Gaikwad, Avinash; Prabhu, S.V.

2015-01-01

Coolant channels of PHWR during accident similar to loss of coolant accident (LOCA) may experience different flow transients with low pressure and low flow conditions. In the advanced PHWRs it is desired to have small amount of positive quality at the exit of the coolant channel to increase the thermal efficiency. Investigation on pressure drop and heat transfer coefficient under subcooled boiling condition is important in the design and operation of the PHWRs. Understanding of thermal hydraulic phenomena associated with horizontal flow is also important in the safety and accident management in these reactors. A detailed experimental investigation on the important thermal hydraulic phenomena of horizontal tubes under low pressure and low flow conditions is carried out. The phenomena covered in this work are measurement of diabatic single phase and subcooled boiling pressure drop and local heat transfer coefficients, steady state CHF, effect of upstream flow restrictions on flow transients and CHF, CHF under oscillatory flow and flow decreasing transients. A detailed literature review is carried out on CHF in horizontal channels to take stock of the works being carried out along with current state of the art and to justify the motivation for the experimental study. This paper presents the review of available literature on horizontal CHF with the results of the experimental work. (author)

Distributed deformation structures in shallow water carbonates subsiding through a simple stress field (Jandaira Formation, NE Brazil)

Science.gov (United States)

Bertotti, Giovanni; Bisdom, Kevin; Bezerra, Hilario; Reijmer, John; Cazarin, Carol

2016-04-01

Despite the scarcity of major deformation structures such as folds and faults, the flat-lying, post-rift shallow water carbonates of the Jandaira Formation (Potiguar Basin, NE Brazil) display well-organized fracture systems distributed of tens of km2. Structures observed in the outcropping carbonates are sub-vertical, generally N-S trending mode I and hybrid veins and barren fractures, sub-vertical roughly E-W trending stylolites and sub-horizontal stylolites. These features developed during subsidence in a simple and constant stress field characterized by, beside gravity, a significant horizontal stress probably of tectonic origin. The corresponding depth curves have different origin and slopes and, therefore, cross each other resulting in position of the principal stresses which change with depth. As a result, the type and amount of fractures affecting subsiding rocks change despite the fact that the far-field stresses remain constant. Following early diagenesis and porosity elimination in the first 100-200m depth, Jandaira carbonates experienced wholesale fracturing at depths of 400-800m resulting in a network of NNW-NE trending fractures partly organized in conjugate sets with a low interfault angle and a sub-vertical intersection, and sub-vertical stylolites roughly perpendicular to the fractures. Intense fluid circulation was activated as a consequence through the carbonates. With increasing subsidence, sub-horizontal stylolites formed providing calcite which precipitated in the open fractures transforming them in veins. The Jandaira formation lost thereby the permeability it had reached during the previous stage. Because of the lack of major deformation, the outcrops of the Jandaira Formation is an excellent analog for carbonate reservoirs in the Middle East, South Atlantic and elsewhere.

Color opponency in cone-driven horizontal cells in carp retina. Aspecific pathways between cones and horizontal cells

NARCIS (Netherlands)

Kamermans, M.; van Dijk, B. W.; Spekreijse, H.

1991-01-01

The spectral and dynamic properties of cone-driven horizontal cells in carp retina were evaluated with silent substitution stimuli and/or saturating background illumination. The aim of this study was to describe the wiring underlying the spectral sensitivity of these cells. We will present

Stress concentration effects in high pressure components

International Nuclear Information System (INIS)

Aller, J.E.

1990-01-01

This paper examines the stress concentration effects of sideholes in thick walled, high pressure cylinders. It has been shown that the theoretical stress concentration factor at the intersection of a small crossbore in a closed end, thick walled cylinder varies between 3.0 and 4.0. Tests have shown that this effect can be greatly reduced in practice by carefully radiusing the bore intersection and autofrettaging the cylinder. It has also been shown that the minimum stress concentration factor occurs when the main bore and sidehole or crossbore have the same diameter, and the radius of the intersection is approximately equal to the sidehole radius. When the bore and sidehole intersection angle decreases from 90 degrees, the stress concentration factor increases significantly. Knowledge of these fundamental relationships can be used in maintaining, as well ad designing, high pressure equipment

Formation evaluation of a horizontal well

International Nuclear Information System (INIS)

Najia, W.K.; Habib, K.H.; Asada, J.

1991-01-01

In Upper Zakum Field, the interest in horizontal drilling has continued. A second horizontal well was drilled during the second half of 1989. This necessitated running logging tools for well control and to evaluate the reservoir characteristics. The logging tool selected for this well is that of Sperry-Sun. Tools configuration and tolerance were found to fulfil SADCO's requirements and specifications. This paper reports on the services produced which included Measurement While Drilling (MWD) directional services and RLL (Recorded Lithology Logging). The RLL services cover Dual Gamma Ray (DGR), Electromagnetic Wave Resistivity (EWR) and Compensated Neutron Porosity (CN porosity). All the RLL tools were an integrated part of the Bottom Hole Drilling Assembly. Data acquired while surveying was recorded in a recording sub down-hole and retrieved when the tools were up at the surface. A PC assisted quick look interpretation was carried out using Archie's equation in shale free limestone to calculate: Effective porosity, Water Saturation and, Bulk water volume

Calculation of vapour bubble growth on the lower generatrix of horizontal tubes

International Nuclear Information System (INIS)

Chajka, V.D.

1987-01-01

The known models of vapour bubble growth are compared with experimental data. Cinematographic study of vapour formation during water boiling was carried out with elements of horizontal tubes of copper 10, 16, 24, 34 and 70 mm in diameter under the pressure of 100 kPa and specific thermal loadings of 20 and 40 kW/m 2 . According to the experimental data the main volume of vapour phase is occupied by vapour bubbles from the lower part of the horizontal tube. Five stages of vapour bubble growth on the lower generatrix of the horizontal tube: nucleation, growth to the point of breaking off from nucleate centre, the breaking off from the nucleate centre, the tube surface flowing around during floating up, the breaking off from the tube surface, were singled out. The shape of vapour volume varied during the whole period of the bubble growth and it was mainly determined by the horizontal tube diameter. The change of vapour bubble radius in time is the function of the horizontal tube diameter. Comparison of the experimental data with the known models of vapour bubble growth has shown, that every stage of vapour bubble growth on the lower generatrix of the tube is determined by the complex of thermal and hydrodynamic conditions, the effect of which depends on the horizontal tube diameter

Accuracy of Single Periapical Radiography in Diagnosis of Horizontal Root Fracture

Directory of Open Access Journals (Sweden)

Fazlolah Soleymani Najafabadi

2012-02-01

Full Text Available Background and Aims: Radiographic examination is a necessary step in diagnosis of horizontal root fracture. The purpose of this study was to determine the sensitivity and specificity of single radiograph for detection of horizontal root fracture. Materials and Methods: In this analytical-descriptive study, 30 human freshly extracted teeth were used. Using a hammer and clamp, the teeth were divided into two sections accidentally and then sections were attached together by cyanoacrylate glue. Two radiographs were taken; with and without a piece of human mandibular bone. Afterward, radiographs were analyzed by three expert dentists using a slide show device. Results: The diagnostic sensitivity and specificity of single radiograph for detection of horizontal root fracture without bone was 100%, but in radiographs of teeth with bone was 82.7% and 100%, respectively. Conclusion: Based on the results of this study, in most cases, the horizontal root fractures can be detected by a single periapical radiograph.

9 CFR 147.51 - Authorized laboratory minimum requirements.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Authorized laboratory minimum requirements. 147.51 Section 147.51 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Authorized Laboratories and Approved Tests § 147.51 Authorized laboratory minimum requirements. These minimum...

Space shuttle orbiter guidance, naviagation and control software functional requirements: Horizontal flight operations

Science.gov (United States)

1972-01-01

The shuttle GN&C software functions for horizontal flight operations are defined. Software functional requirements are grouped into two categories: first horizontal flight requirements and full mission horizontal flight requirements. The document privides the intial step in the shuttle GN&C software design process. It also serves as a management tool to identify analyses which are required to define requirements.

Thermal transient analysis applied to horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Duong, A.N. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[ConocoPhillips Canada Resources Corp., Calgary, AB (Canada)

2008-10-15

Steam assisted gravity drainage (SAGD) is a thermal recovery process used to recover bitumen and heavy oil. This paper presented a newly developed model to estimate cooling time and formation thermal diffusivity by using a thermal transient analysis along the horizontal wellbore under a steam heating process. This radial conduction heating model provides information on the heat influx distribution along a horizontal wellbore or elongated steam chamber, and is therefore important for determining the effectiveness of the heating process in the start-up phase in SAGD. Net heat flux estimation in the target formation during start-up can be difficult to measure because of uncertainties regarding heat loss in the vertical section; steam quality along the horizontal segment; distribution of steam along the wellbore; operational conditions; and additional effects of convection heating. The newly presented model can be considered analogous to pressure transient analysis of a buildup after a constant pressure drawdown. The model is based on an assumption of an infinite-acting system. This paper also proposed a new concept of a heating ring to measure the heat storage in the heated bitumen at the time of testing. Field observations were used to demonstrate how the model can be used to save heat energy, conserve steam and enhance bitumen recovery. 18 refs., 14 figs., 2 appendices.

Determination of service stresses in pretensioned beams, final report, December 2009.

Science.gov (United States)

2009-12-01

This report presents research on the evaluation of service flexural stresses and cracking moment in prestressed concrete members and on the minimum reinforcement requirements that are currently controlled by the flexural cracking moment. In prestress...

Vertical and horizontal differences of soil parameters and radiocaesium contents in soil profiles (dystric cambisol) under spruce

International Nuclear Information System (INIS)

Strebl, F.; Gerzabek, M.

1997-05-01

In a spruce forest stand 9 pooled soil profiles (ten auger cores each, 4 layers) were collected within a homogeneous area of 200 ha. This sampling technique provides sufficient accuracy for the determination of most physico-chemical soil characteristics as well as for the assessment of vertical gradients and horizontal variability within the investigation area. The results reveal the soils' tendency for podsolization and acidification processes. In spite of the small sample sizes cation wash-out (Ca, Mg) due to differences in the orographic situation was determined with high significance. 86 % of 137 Cs-contamination derived from the Chernobyl-fallout in 1986 are still found in the top-soil (10 cm). Nutrient-cycling and the high binding capacity of soil organic matter retard vertical migration of 137 Cs in forest soils effectively. From the present data sets for different soil parameters the minimum number of soil samples ensuring maximum admissible errors of 10 and 20 % were calculated. (author)

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures.

Science.gov (United States)

Addai, Emmanuel Kwasi; Gabel, Dieter; Krause, Ulrich

2016-04-15

The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. Copyright © 2016 Elsevier B.V. All rights reserved.

Should tsunami models use a nonzero initial condition for horizontal velocity?

Science.gov (United States)

Nava, G.; Lotto, G. C.; Dunham, E. M.

2017-12-01

Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require two initial conditions: one on sea surface height and another on depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). We run several full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor, using both idealized structures and a more realistic Tohoku structure. Substantial horizontal momentum is imparted to the ocean, but almost all momentum is carried away in the form of ocean acoustic waves. We compare tsunami propagation in each full-physics simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial conditions. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves (from ocean acoustic and seismic waves) at some final time, and backpropagating the tsunami

Applying the Helmholtz Illusion to Fashion: Horizontal Stripes Won't Make You Look Fatter

Directory of Open Access Journals (Sweden)

Peter Thompson

2011-01-01

Full Text Available A square composed of horizontal lines appears taller and narrower than an identical square made up of vertical lines. Reporting this illusion, Hermann von Helmholtz noted that such illusions, in which filled space seems to be larger than unfilled space, were common in everyday life, adding the observation that ladies' frocks with horizontal stripes make the figure look taller. As this assertion runs counter to modern popular belief, we have investigated whether vertical or horizontal stripes on clothing should make the wearer appear taller or fatter. We find that a rectangle of vertical stripes needs to be extended by 7.1% vertically to match the height of a square of horizontal stripes and that a rectangle of horizontal stripes must be made 4.5% wider than a square of vertical stripes to match its perceived width. This illusion holds when the horizontal or vertical lines are on the dress of a line drawing of a woman. We have examined the claim that these effects apply only for 2-dimensional figures in an experiment with 3-D cylinders and find no support for the notion that horizontal lines would be ‘fattening’ on clothes. Significantly, the illusion persists when the horizontal or vertical lines are on pictures of a real half-body mannequin viewed stereoscopically. All the evidence supports Helmholtz's original assertion.

Formulation of fracture gradient extension equations in the Sergipe Basin-Brazil

Energy Technology Data Exchange (ETDEWEB)

Suzart, J. Walter P.; Moreto, Rodrigo [Halliburton, Rio de Janeiro, RJ (Brazil); Luduvice, Roberto; Gomes, Isaac Santana; Richard Junior, Emerson [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

One of the challenges of drilling exploration wells is to accurately estimate fracture gradients. This may cause formation damage and lead to premature hydraulic fracturing and prevent an optimum hydraulic design during completion. To avoid this scenario, it is important to know the minimum pressure that causes fractures. This estimation may be based on density, overburden, Poisson's ratio, and minimum horizontal stress. It is now possible to monitor fracturing stimulation operations in real time, which allows real-time understanding of formation pressure response, including fracture extension behavior and screen out. It is possible to avoid risks related to unexpected high pressure applied on the formation while drilling and maintain well and equipment integrities. This may prevent non-productive time (NPT) caused by unplanned well-cleaning operations and material expenses. Real-time fracturing information is usually obtained from step-rate and/or mini-frac analyses. However, there are some scenarios where these tests and analyses may be uneconomical. This paper details an alternative solution. It uses modified Eaton's equations that are representative of the area of interest, which in the present case is the Sergipe Basin located in northeast Brazil. The modified Eaton's equations are used to estimate parameters of the minimum horizontal stress, fracture extension gradient, overburden, and Poisson's ratio. This is based on hydraulic fracturing jobs and density logs available from different locations within the Sergipe Basin. To validate the present method, the estimation results were compared with available step-rate test results for the area. (author)

Horizontally viscous effects in a tidal basin : Extending Taylor’s problem

NARCIS (Netherlands)

Roos, P.C.; Schuttelaars, H.M.

2009-01-01

The classical problem of Taylor (Proc. Lond. Math. Soc., vol. 20, 1921, pp. 148–181) of Kelvin wave reflection in a semi-enclosed rectangular basin of uniform depth is extended to account for horizontally viscous effects. To this end, we add horizontally viscous terms to the hydrodynamic model

Special wrench for B-nuts reduces torque stress in tubing

Science.gov (United States)

Stein, J. A.

1970-01-01

Gear-driven torque wrench with bearing support is used to tighten B-nut connection of partially supported fluid line with minimum stress to adjacent tubing and fittings. Wrench is useful for working with weak or brittle lines such as glass tubing.

Minimizing stress in large-area surface micromachined perforated membranes with slits

International Nuclear Information System (INIS)

Ghaderi, M; Ayerden, N P; De Graaf, G; Wolffenbuttel, R F

2015-01-01

This paper presents the effectiveness of both design and fabrication techniques for avoiding the rupturing or excessive bending of perforated membranes after release in surface micromachining. Special lateral designs of arrays of slits in the membrane were investigated for a maximum yield at a given level of residual stress. Process parameters were investigated and optimized for minimum residual stress in multilayer thin-film membranes. A 2 µm thick sacrificial TEOS layer and a structural membrane that is composed of silicon nitride and polysilicon layers in the stack is the basis of this study. The effect of sharp corners on the local stress in membranes was investigated, and structures are proposed that reduce these effects, maximizing the yield at a given level of residual stress. The effects of perforation and slits were studied both theoretically and using finite element analysis. While the overall effect of perforation is negligible in typical MEMS structures, an optimum design for the slits reduces the von Mises stress considerably as compared to sharp corners. The fabrication process was also investigated and optimized for the minimum residual stress of both the layers within the stack and the complete layer stack. The main emphasis of this work is on placing a stress-compensating layer on the wafer backside and simultaneously removing it during the surface micromachining, as this has been found to be the most effective method to reduce the overall stress in a stack of layers after sacrificial etching. Implementation of a stress compensating layer reduced the total residual stress from 200 MPa compressive into almost 60 MPa, tensile. Even though a particular structure was studied here, the employed methods are expected to be applicable to similar MEMS design problems. (paper)

Horizontal H 2-air turbulent buoyant jet resulting from hydrogen leakage

KAUST Repository

El-Amin, Mohamed

2012-02-01

The current article is devoted to introducing mathematical and physical analyses with numerical investigation of a buoyant jet resulting from hydrogen leakage in air from a horizontal round source. H 2-air jet is an example of the non-Boussinesq buoyant jet in which a low-density gas jet is injected/leak into a high-density ambient. The density of the mixture is a function of the concentration only, the binary gas mixture is assumed to be of a linear mixing type and the rate of entrainment is assumed to be a function of the plume centerline velocity and the ratio of the mean plume and ambient densities. On the other hand, the local rate of entrainment consists of two components; one is the component of entrainment due to jet momentum while the other is the component of entrainment due to buoyancy. The top-hat profile assumption is used to obtain the mean centerline velocity, width, density and concentration of the H 2-air horizontal jet in addition to kinematic relations which govern the jet trajectories. A set of ordinary differential equations is obtained and solved numerically using Runge-Kutta method. In the second step, the mean axial velocity, mean concentration and mean density of the jet are obtained based on Gaussian model. Finally, several quantities of interest, including the cross-stream velocity, Reynolds stress, velocity-concentration correlation (radial flux), turbulent eddy viscosity and turbulent eddy diffusivity, are obtained by solving the governing partial differential equations. Additionally, the turbulent Schmidt number is estimated and the normalized jet-feed material density and the normalized momentum flux density are correlated. © 2011, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Multivariate recurrence network analysis for characterizing horizontal oil-water two-phase flow.

Science.gov (United States)

Gao, Zhong-Ke; Zhang, Xin-Wang; Jin, Ning-De; Marwan, Norbert; Kurths, Jürgen

2013-09-01

Characterizing complex patterns arising from horizontal oil-water two-phase flows is a contemporary and challenging problem of paramount importance. We design a new multisector conductance sensor and systematically carry out horizontal oil-water two-phase flow experiments for measuring multivariate signals of different flow patterns. We then infer multivariate recurrence networks from these experimental data and investigate local cross-network properties for each constructed network. Our results demonstrate that a cross-clustering coefficient from a multivariate recurrence network is very sensitive to transitions among different flow patterns and recovers quantitative insights into the flow behavior underlying horizontal oil-water flows. These properties render multivariate recurrence networks particularly powerful for investigating a horizontal oil-water two-phase flow system and its complex interacting components from a network perspective.

Detection of Horizontal Gene Transfers from Phylogenetic Comparisons

Science.gov (United States)

Pylro, Victor Satler; Vespoli, Luciano de Souza; Duarte, Gabriela Frois; Yotoko, Karla Suemy Clemente

2012-01-01

Bacterial phylogenies have become one of the most important challenges for microbial ecology. This field started in the mid-1970s with the aim of using the sequence of the small subunit ribosomal RNA (16S) tool to infer bacterial phylogenies. Phylogenetic hypotheses based on other sequences usually give conflicting topologies that reveal different evolutionary histories, which in some cases may be the result of horizontal gene transfer events. Currently, one of the major goals of molecular biology is to understand the role that horizontal gene transfer plays in species adaptation and evolution. In this work, we compared the phylogenetic tree based on 16S with the tree based on dszC, a gene involved in the cleavage of carbon-sulfur bonds. Bacteria of several genera perform this survival task when living in environments lacking free mineral sulfur. The biochemical pathway of the desulphurization process was extensively studied due to its economic importance, since this step is expensive and indispensable in fuel production. Our results clearly show that horizontal gene transfer events could be detected using common phylogenetic methods with gene sequences obtained from public sequence databases. PMID:22675653

Columnar interactions determine horizontal propagation of recurrent network activity in neocortex

Science.gov (United States)

Wester, Jason C.; Contreras, Diego

2012-01-01

The cortex is organized in vertical and horizontal circuits that determine the spatiotemporal properties of distributed cortical activity. Despite detailed knowledge of synaptic interactions among individual cells in the neocortex, little is known about the rules governing interactions among local populations. Here we used self-sustained recurrent activity generated in cortex, also known as up-states, in rat thalamocortical slices in vitro to understand interactions among laminar and horizontal circuits. By means of intracellular recordings and fast optical imaging with voltage sensitive dyes, we show that single thalamic inputs activate the cortical column in a preferential L4→L2/3→L5 sequence, followed by horizontal propagation with a leading front in supra and infragranular layers. To understand the laminar and columnar interactions, we used focal injections of TTX to block activity in small local populations, while preserving functional connectivity in the rest of the network. We show that L2/3 alone, without underlying L5, does not generate self-sustained activity and is inefficient propagating activity horizontally. In contrast, L5 sustains activity in the absence of L2/3 and is necessary and sufficient to propagate activity horizontally. However, loss of L2/3 delays horizontal propagation via L5. Finally, L5 amplifies activity in L2/3. Our results show for the first time that columnar interactions between supra and infragranular layers are required for the normal propagation of activity in the neocortex. Our data suggest that supra and infragranular circuits with their specific and complex set of inputs and outputs, work in tandem to determine the patterns of cortical activation observed in vivo. PMID:22514308

Aspectos históricos da visita de Marie Sklodowska Curie a Belo Horizonte

Directory of Open Access Journals (Sweden)

Cássius Klay Nascimento

2011-01-01

Full Text Available In the year 2011 it is celebrated the Marie Sklodowska Curie Nobel Prize centenary and the International Year of Chemistry. However, it is not generally known that Marie Sklodowska Curie, one of the greatest scientists of all time, visited Belo Horizonte, state of Minas Gerais, Brazil. She arrived by train at Belo Horizonte city on 16 August 1926, coming from Rio de Janeiro and accompanied by her daughter Irène Joliot-Curie. The scientists visited the Institute of Radium of Belo Horizonte. The approach in this work emphasizes the presence of Marie Sklodowska Curie in Belo Horizonte, exploring the admiration and respect that people had for her.

Stress/Rest Tc-99m-MIBI SPECT in Comparison with Rest/Stress Rubidium - 82 PET

International Nuclear Information System (INIS)

Lee, D. S.; Kamg, K. W.; Lee, K. H.; Jeong, J. M.; Kwark, C. E.; Chung, J. K.; Lee, M.C.; Seo, J. D.; Koh, C. S.

1995-01-01

We compared stress/rest myocardial Tc-99m-MIBI tomographic image findings with rest/stress rubidium-82 tomographic images. In 23 patients with coronary artery disease (12 of them received bypass grafts before) and 6 normal subjects, rest rubidium PET study was performed, rubidium-82 and Tc-99m-MIBI were injected simultaneously to each patient after dipyridamole stress for rubidium PET and MIBI SPECT; and rest MIBI SPECT was performed 4 hours thereafter. We scored segmental decrease of rubidium, or MIBI uptakes into 5 grades for 29 segments from 3 short-axis, vertical and horizontal slices. Scores were summed for each major arterial territory. When more score than two grade-2's or one grade-3 was considered as the cue for significant stenosis for major arterial territories, 67% of 46 stenosed arteries were found with MIBI studies and 78% of them by rubidium studies. Fourteen among 28 grafted arterial territories of 12 post-CABG patients were found normal with both rubidium and MIBI. Segmental scores were concordant between rubidium and MIBI in 72% of 709-stress segments and in 80% of 825 rest segments. Stress rubidium segmental scores were less than stress MIBI scores in 9%, so were rest rubidium scores. Stress rubidium scores were more than stress MIBI scores in 20% of segments, and rest rubidium segmental scores were more than rest MIBI scores in 11%. Rank correlations (Spearman's rho's more than 0.7(stress) and 0.5(rest), slopes (MIBI/rubidium) around 0.7(stress) and 0.9(rest) suggested deeper and wider defects in stress with rubidium. Slope over 1 (MIBI/rubidium) with LAD segmental scores at rest and 7 territories which had much larger score with MIBI revealed exaggeration of rest defects with rest MIBI in same-day stress/rest study. Difference scores (stress-rest for each territory) suggesting ischemia were larger with rubidium (slope of MIBI/rubidium around 0.45). As has been implied by animal or separate-day- human studies, these segmental analyses with

Plane-stress fields for sharp notches in pressure-sensitive materials

International Nuclear Information System (INIS)

Al-Abduljabbar, Abdulhamid

2003-01-01

The effect of pressure sensitive yield on materials toughness can be determined by investigating stress fields around cracks and notches. In this work, fully-developed plastic stress fields around sharp wedge-shaped notches of perfectly-plastic pressure-sensitive materials are investigated for plane-stress case and Mode 1 loading condition. The pressure-sensitive yielding behavior is represented using the Drucker-Prager criterion. Using equilibrium equations, boundary conditions, and the yield criterion, closed-form expressions for stress fields are derived. The analysis covers the gradual change in the notch angle and compares it with the limiting case of a pure horizontal crack. Effects of notch geometry and pressure sensitivity on stress fields are examined by considering different specimen geometries, as well as different levels of pressure sensitivity. Results indicate that while the stress values directly ahead of the notch-tip are not affected, the extent of stress sector at notch front is reduced, thereby causing increase in the radial stress value around the notch. As the pressure sensitivity increases the reduction of the stress sector directly ahead of the notch tip is more evident. Also, for high pressure sensitivity values, introduction of the notch angle reduces the variation of the stress levels. Results are useful for design of structural components. (author)

Minimum Price Guarantees In a Consumer Search Model

NARCIS (Netherlands)

M.C.W. Janssen (Maarten); A. Parakhonyak (Alexei)

2009-01-01

textabstractThis paper is the first to examine the effect of minimum price guarantees in a sequential search model. Minimum price guarantees are not advertised and only known to consumers when they come to the shop. We show that in such an environment, minimum price guarantees increase the value of

Stress evolution and fault stability during the Weichselian glacial cycle

International Nuclear Information System (INIS)

Lund, Bjoern; Schmidt, Peter; Hieronymus, Christoph

2009-01-01

In this report we examine how the waxing and waning of an ice sheet during a glacial cycle affects the state of stress in the Earth, and how those changes in stress influence the stability of faults. We focus on the stresses at repository depth in Forsmark and Oskarshamn, and on the stability field at seismogenic depth at the proposed repository sites and at the Paervie endglacial fault in northern Sweden. This study is a modelling study, where we use three-dimensional ice and earth models to calculate the glacial isostatic adjustment (GIA), i.e. the response of the Earth to an ice load, examining both displacements and stresses. We use a flat-earth finite element approach, based on Wu with some modifications. The result presented here is a continuation of previous studies in two dimensions and complement those studies in assessing how the three-dimensionality of the problem affects the conclusions. We use the Fennoscandian ice model of Naeslund, which is a dynamic ice sheet model based on climate reconstructions with constraints from geological observations. The ice model spans the entire Weichselian glaciation but we only use the last 68 kyr, which includes the two major periods of ice cover as depicted in this ice sheet reconstruction. For the GIA calculation we use a number of different earth models, both with flat horizontal layers and with various 3D structures of lithosphere thickness. We do not include lateral variations in the viscosity of the mantle. Comparing the current day rebound velocities predicted by our models with GPS observations from the BIFROST project, we note that in general, we can obtain a reasonable fit to the observations with our models, and that the results are rather sensitive to the assumed viscosity of the mantle. We also find that the differences between data and model results, for all earth models, have common features which we interpret as due to the ice model. These observations are in agreement with numerous other GIA studies

Bridging scales of crustal stress patterns using the new World Stress Map

Science.gov (United States)

Heidbach, O.; Rajabi, M.; Cui, X.; Fuchs, K. W.; Mueller, B.; Reinecker, J.; Reiter, K.; Tingay, M. R. P.; Wenzel, F.; Xie, F.; Ziegler, M.; Zoback, M. D.; Zoback, M. L.

2017-12-01

Knowledge of the contemporary crustal stress field is a key parameter for the understanding of geodynamic processes such as global plate tectonics and the earthquake cycle. It is also an essential parameter for our sustainable and safe usage of Earth's resources, which is a major challenge for energy security in the 21st century. Since 1986, the World Stress Map (WSM) project has systematically compiled present-day stress information and provides a unique public domain global database. It is a long-term project based on an international network of partners from academia and industry. All data are public and available on the project website at world-stress-map.org. For the 30th anniversary of the project a new database has been compiled, containing double the amount of data records (n=42,870) including new data records from almost 4,000 deep boreholes. The new compilation focused on areas with previously sparse data coverage in order to resolve the stress pattern on different spatial scales. The significantly higher data density can now be used to resolve stress pattern heterogeneities on regional and local scales, as well as with depth in some regions. We present three results derived from the new WSM compilation: 1.) The global comparison between absolute plate motion and the mean of the orientation of maximum horizontal stress SHmax on a regular grid shows that there is still a correlation for the North and South America plate, but deviations from this general trend are now also clearly resolved. 2.) The variability of the crustal stress pattern changes when zooming in from plate-wide scale down to basin scale at 100 km. We show examples for Eastern Australia, Oklahoma and Central Europe. This regional and local variability of the stress pattern can be used as a proxy to identify and quantify regional and local stress sources by means of geomechanical-numerical models of the 3D stress tensor. 3.) Finally we present briefly the general concept of a multi-stage 3D

Electron-shading effect on the horizontal aligned growth of carbon nanotubes

International Nuclear Information System (INIS)

Chai Yang; Xiao Zhiyong; Chan, Philip C. H.

2009-01-01

Based on the well-accepted electron-shading theory during plasma processing, we designed microstructures to control the local built-in electric-field on the substrate surface. The distortion magnitude of the electric-field is largest near the sidewalls of the microstructures, creating a horizontal electric-field in this region. We showed that the horizontally aligned carbon nanotubes (CNTs) were grown by making use of this built-in electric-field during the plasma-enhanced chemical vapor deposition process, with a tactical choice of geometries and materials of the microstructures on the substrate. This technique opens up a way to selectively and controllably grow horizontally aligned CNTs on the substrate surface

Interaction between the soma and the axon terminal of horizontal cells in carp retina

NARCIS (Netherlands)

Kamermans, M.; van Dijk, B. W.; Spekreijse, H.

1990-01-01

In teleost retina, the receptive fields of horizontal cell axon terminals have a larger space constant than the receptive fields of the horizontal cell somata. Generally this difference in receptive field size is attributed to the cell coupling which is assumed to be stronger in the horizontal axon

Horizontal oil well applications and oil recovery assessment. Volume 2: Applications overview, Final report

Energy Technology Data Exchange (ETDEWEB)

Deskins, W.G.; McDonald, W.J.; Knoll, R.G.; Springer, S.J.

1995-03-01

Horizontal technology has been applied in over 110 formations in the USA. Volume 1 of this study addresses the overall success of horizontal technology, especially in less-publicized formations, i.e., other than the Austin Chalk, Bakken, and Niobrara. Operators in the USA and Canada were surveyed on a formation-by-formation basis by means of a questionnaire. Response data were received describing horizontal well projects in 58 formations in the USA and 88 in Canada. Operators` responses were analyzed for trends in technical and economic success based on lithology (clastics and carbonates) and resource type (light oil, heavy oil, and gas). The potential impact of horizontal technology on reserves was also estimated. A forecast of horizontal drilling activity over the next decade was developed.

Love-type wave propagation in a pre-stressed viscoelastic medium influenced by smooth moving punch

Science.gov (United States)

Singh, A. K.; Parween, Z.; Chatterjee, M.; Chattopadhyay, A.

2015-04-01

In the present paper, a mathematical model studying the effect of smooth moving semi-infinite punch on the propagation of Love-type wave in an initially stressed viscoelastic strip is developed. The dynamic stress concentration due to the punch for the force of a constant intensity has been obtained in the closed form. Method based on Weiner-hopf technique which is indicated by Matczynski has been employed. The study manifests the significant effect of various affecting parameters viz. speed of moving punch associated with Love-type wave speed, horizontal compressive/tensile initial stress, vertical compressive/tensile initial stress, frequency parameter, and viscoelastic parameter on dynamic stress concentration due to semi-infinite punch. Moreover, some important peculiarities have been traced out and depicted by means of graphs.

Wage inequality, minimum wage effects and spillovers

OpenAIRE

Stewart, Mark B.

2011-01-01

This paper investigates possible spillover effects of the UK minimum wage. The halt in the growth in inequality in the lower half of the wage distribution (as measured by the 50:10 percentile ratio) since the mid-1990s, in contrast to the continued inequality growth in the upper half of the distribution, suggests the possibility of a minimum wage effect and spillover effects on wages above the minimum. This paper analyses individual wage changes, using both a difference-in-differences estimat...

Wind Stress Variability Observed Over Coastal Waters

Science.gov (United States)

Ortiz-Suslow, D. G.; Haus, B. K.; Laxague, N.; Williams, N. J.; Graber, H. C.

2016-02-01

The wind stress on the ocean surface generates waves, drives currents, and enhances gas exchange; and a significant amount of work has been done to characterize the air-sea momentum flux in terms of bulk oceanographic and atmospheric parameters. However, the majority of this work to develop operational algorithms has been focused on the deep ocean and the suitability of these methods in the coastal regime has not been evaluated. The findings from a two-part field campaign will be presented which highlight the divergence of nearshore wind stress observations from conventional, deep water results. The first set of data comes from a coastal region near a relatively small, natural tidal inlet. A high degree of spatial variability was observed in both the wind stress magnitude and direction, suggestive of coastal processes (e.g., depth-limited wave affects and horizontal current shear) modulating the momentum flux from the atmosphere to the ocean surface. These shallow-water processes are typically not accounted for in conventional parameterizations. Across the experimental domain and for a given wind speed, the stress magnitude was found to be nearly 2.5 times that predicted by conventional methods; also, a high propensity for stress steering off the mean azimuthal wind direction (up to ±70 degrees) was observed and linked to horizontal current gradients produced by the tidal inlet. The preliminary findings from a second data set taken in the vicinity of the macrotidal Columbia River Mouth will also be presented. Compared to the first data set, a similar degree of variability is observed here, but the processes responsible for this are present at a much larger scale. Specifically, the Columbia River Mouth observations were made in the presence of significant swell wave energy and during periods of very high estuarine discharge. The relative angle between the wind and swell direction is expected to be significant with regards to the observed momentum flux. Also, these

Cell-specific cre recombinase expression allows selective ablation of glutamate receptors from mouse horizontal cells.

Directory of Open Access Journals (Sweden)

Sebastian Ströh

Full Text Available In the mouse retina, horizontal cells form an electrically coupled network and provide feedback signals to photoreceptors and feedforward signals to bipolar cells. Thereby, horizontal cells contribute to gain control at the first visual synapse and to the antagonistic organization of bipolar and ganglion cell receptive fields. However, the nature of horizontal cell output remains a matter of debate, just as the exact contribution of horizontal cells to center-surround antagonism. To facilitate studying horizontal cell function, we developed a knockin mouse line which allows ablating genes exclusively in horizontal cells. This knockin line expresses a Cre recombinase under the promoter of connexin57 (Cx57, a gap junction protein only expressed in horizontal cells. Consistently, in Cx57+/Cre mice, Cre recombinase is expressed in almost all horizontal cells (>99% and no other retinal neurons. To test Cre activity, we crossbred Cx57+/Cre mice with a mouse line in which exon 11 of the coding sequence for the ionotropic glutamate receptor subunit GluA4 was flanked by two loxP sites (GluA4fl/fl. In GluA4fl/fl:Cx57+/Cre mice, GluA4 immunoreactivity was significantly reduced (∼ 50% in the outer retina where horizontal cells receive photoreceptor inputs, confirming the functionality of the Cre/loxP system. Whole-cell patch-clamp recordings from isolated horizontal cell somata showed a reduction of glutamate-induced inward currents by ∼ 75%, suggesting that the GluA4 subunit plays a major role in mediating photoreceptor inputs. The persistent current in GluA4-deficient cells is mostly driven by AMPA and to a very small extent by kainate receptors as revealed by application of the AMPA receptor antagonist GYKI52466 and concanavalin A, a potentiator of kainate receptor-mediated currents. In summary, the Cx57+/Cre mouse line provides a versatile tool for studying horizontal cell function. GluA4fl/fl:Cx57+/Cre mice, in which horizontal cells receive less

Cell-Specific Cre Recombinase Expression Allows Selective Ablation of Glutamate Receptors from Mouse Horizontal Cells

Science.gov (United States)

Janssen-Bienhold, Ulrike; Schultz, Konrad; Cimiotti, Kerstin; Weiler, Reto; Willecke, Klaus; Dedek, Karin

2013-01-01

In the mouse retina, horizontal cells form an electrically coupled network and provide feedback signals to photoreceptors and feedforward signals to bipolar cells. Thereby, horizontal cells contribute to gain control at the first visual synapse and to the antagonistic organization of bipolar and ganglion cell receptive fields. However, the nature of horizontal cell output remains a matter of debate, just as the exact contribution of horizontal cells to center-surround antagonism. To facilitate studying horizontal cell function, we developed a knockin mouse line which allows ablating genes exclusively in horizontal cells. This knockin line expresses a Cre recombinase under the promoter of connexin57 (Cx57), a gap junction protein only expressed in horizontal cells. Consistently, in Cx57+/Cre mice, Cre recombinase is expressed in almost all horizontal cells (>99%) and no other retinal neurons. To test Cre activity, we crossbred Cx57+/Cre mice with a mouse line in which exon 11 of the coding sequence for the ionotropic glutamate receptor subunit GluA4 was flanked by two loxP sites (GluA4fl/fl). In GluA4fl/fl:Cx57+/Cre mice, GluA4 immunoreactivity was significantly reduced (∼50%) in the outer retina where horizontal cells receive photoreceptor inputs, confirming the functionality of the Cre/loxP system. Whole-cell patch-clamp recordings from isolated horizontal cell somata showed a reduction of glutamate-induced inward currents by ∼75%, suggesting that the GluA4 subunit plays a major role in mediating photoreceptor inputs. The persistent current in GluA4-deficient cells is mostly driven by AMPA and to a very small extent by kainate receptors as revealed by application of the AMPA receptor antagonist GYKI52466 and concanavalin A, a potentiator of kainate receptor-mediated currents. In summary, the Cx57+/Cre mouse line provides a versatile tool for studying horizontal cell function. GluA4fl/fl:Cx57+/Cre mice, in which horizontal cells receive less excitatory input

Horizonte construido. Transformación del paisaje en la Casa Huarte

Directory of Open Access Journals (Sweden)

Pablo Olalquiaga Bescós

2014-02-01

Full Text Available La Casa Huarte (Madrid, 1966 representa, ante todo, una actuación en el paisaje. Sus creadores, José Antonio Corrales y Ramón Vázquez Molezún, invirtieron un método utilizado en proyectos anteriores (Instituto en Herrera de Pisuerga, Residencia en Miraflores, Pabellón de Bruselas donde la edificación se adecuaba al medio y el paisaje donde se insertaba. Mediante una transformación topográfica Corrales y Molezún construyeron un lugar en el que el horizonte, entendido como el paisaje formado por el encuentro de planos donde converge nuestra mirada, fue modificado. Cuando esto ocurre se produce una alteración de la mirada del observador, se “construye” un nuevo horizonte visual que es en definitiva el horizonte de la arquitectura, en el que los límites están definidos por los distintos planos. En esta construcción del nuevo horizonte, en la creación de nuevas experiencias visuales, las esculturas y los árboles, situadas en las plataformas de los patios de la Casa Huarte, se convirtieron en referencias visuales que alteraban los ángulos de visión previamente establecidos por la arquitectura. Estas siluetas incorporan nuevos puntos de referencia en ese horizonte, proporcionando profundidad, perspectiva y una escala intermedia entre la intimidad del observador y la monumentalidad del infinito

A comparative pressure analysis of air flow between horizontal and V-Tail of UAV MALE of NACA0012H with speed variation

OpenAIRE

Riza Rahmat; Kurniawan Dicky; Wicaksono Arif Budi

2018-01-01

NACA0012H is an airfoil type that could be used for Unmanned Aerial Vehicle Medium Altitude Long Endurance. This experiment was used to analyze stress in the surface of Tail of UAV MALE that was caused by air flow. The experiment was conducted using Computational Fluid Dynamics Software. Two designs of tail, horizontal and V-tail, were considered to simulate pressure occurred on the surface of leading edge, chamber and trailing edge. The simulation was developed varying the speed of the UAV M...

Numerical simulations of a horizontal axis water turbine designed for underwater mooring platforms

Directory of Open Access Journals (Sweden)

Wenlong Tian

2016-01-01

Full Text Available In order to extend the operational life of Underwater Moored Platforms (UMPs, a horizontal axis water turbine is designed to supply energy for the UMPs. The turbine, equipped with controllable blades, can be opened to generate power and charge the UMPs in moored state. Three-dimensional Computational Fluid Dynamics (CFD simulations are performed to study the characteristics of power, thrust and the wake of the turbine. Particularly, the effect of the installation position of the turbine is considered. Simulations are based on the Reynolds Averaged Navier-Stokes (RANS equations and the shear stress transport k-ω turbulent model is utilized. The numerical method is validated using existing experimental data. The simulation results show that this turbine has a maximum power coefficient of 0.327 when the turbine is installed near the tail of the UMP. The flow structure near the blade and in the wake are also discussed.

Soret-driven double diffusive magneto-convection in couple stress liquid

Directory of Open Access Journals (Sweden)

Mishra P.

2012-07-01

Full Text Available The stability analysis of Soret driven double diffusive convection for electrically conducting couple stress liquid is investigated theoretically. The couple stress liquid is confined between two horizontal surfaces and a constant vertical magnetic field is applied across the surfaces. Linear stability analysis is used to investigate the effect of various parameters on the onset of convection. Effect of magnetic field on the onset of convection is presented by means of Chandrasekhar number. The problem is analyzed as a function of Chandrasekhar number (Q, positive and negative Soret parameter (S r and couple stress parameter (C, mainly. The results show that the Q, both positive and negative Sr and C delay the onset of convection. The effect of other parameters is also discussed in paper and shown by graphs.

Stress analysis of two methods of ceramic inlay preparation by finite element

Directory of Open Access Journals (Sweden)

Leila Pishevar

2014-01-01

Conclusion: Cements with minimum shrinkage and as thin layer as possible should be used. Filling the undercut with glass ionomer cement decreases the stress. Other experimental and clinical studies must follow this research.

Minimum Variance Portfolios in the Brazilian Equity Market

Directory of Open Access Journals (Sweden)

Alexandre Rubesam

2013-03-01

Full Text Available We investigate minimum variance portfolios in the Brazilian equity market using different methods to estimate the covariance matrix, from the simple model of using the sample covariance to multivariate GARCH models. We compare the performance of the minimum variance portfolios to those of the following benchmarks: (i the IBOVESPA equity index, (ii an equally-weighted portfolio, (iii the maximum Sharpe ratio portfolio and (iv the maximum growth portfolio. Our results show that the minimum variance portfolio has higher returns with lower risk compared to the benchmarks. We also consider long-short 130/30 minimum variance portfolios and obtain similar results. The minimum variance portfolio invests in relatively few stocks with low βs measured with respect to the IBOVESPA index, being easily replicable by individual and institutional investors alike.

Interplay between cytoskeletal stresses and cell adaptation under chronic flow.

Directory of Open Access Journals (Sweden)

Deepika Verma

Full Text Available Using stress sensitive FRET sensors we have measured cytoskeletal stresses in α-actinin and the associated reorganization of the actin cytoskeleton in cells subjected to chronic shear stress. We show that long-term shear stress reduces the average actinin stress and this effect is reversible with removal of flow. The flow-induced changes in cytoskeletal stresses are found to be dynamic, involving a transient decrease in stress (phase-I, a short-term increase (3-6 min (Phase-II, followed by a longer-term decrease that reaches a minimum in ~20 min (Phase-III, before saturating. These changes are accompanied by reorganization of the actin cytoskeleton from parallel F-actin bundles to peripheral bundles. Blocking mechanosensitive ion channels (MSCs with Gd(3+ and GsMTx4 (a specific inhibitor eliminated the changes in cytoskeletal stress and the corresponding actin reorganization, indicating that Ca(2+ permeable MSCs participate in the signaling cascades. This study shows that shear stress induced cell adaptation is mediated via MSCs.

Rock stress measurements in the Grimsel Underground Rock Laboratory and their geological interpretation

International Nuclear Information System (INIS)

Braeuer, V.; Heusermann, S.; Pahl, A.

1989-01-01

Rock stress is being studied as part of the Swiss-German cooperation between the National Cooperative for the Storage of Radioactive Waste (NAGRA), the Research Centre for Environmental Sciences (GSF), and the Federal Institute for Geosciences and Natural Resources (BGR) in the Grimsel Rock Laboratory in Switzerland. Several methods and various equipment for measuring rock stress have been developed and tested in an approximately 200-m borehole drilled from a gallery at a depth of 450 m. The measurements were made continually during overcoring; the data were recorded and processed in a computer located downhole or outside the borehole. The results of the overcoring tests and of frac tests indicate a principle horizontal stress of 25-40 MPa, directed mainly NW-SE. Detailed geological mapping shows relationships between stress and rock structure. A zone of nearly unfractured rock exhibits an increase in stress and a change in stress direction. (orig.)

Minimum Covers of Fixed Cardinality in Weighted Graphs.

Science.gov (United States)

White, Lee J.

Reported is the result of research on combinatorial and algorithmic techniques for information processing. A method is discussed for obtaining minimum covers of specified cardinality from a given weighted graph. By the indicated method, it is shown that the family of minimum covers of varying cardinality is related to the minimum spanning tree of…

The role of vertical shear on the horizontal oceanic dispersion

OpenAIRE

A. S. Lanotte; R. Corrado; G. Lacorata; L. Palatella; C. Pizzigalli; I. Schipa; R. Santoleri

2015-01-01

The effect of vertical shear on the horizontal dispersion properties of passive tracer particles on the continental shelf of South Mediterranean is investigated by means of observative and model data. In-situ current measurements reveal that vertical velocity gradients in the upper mixed layer decorrelate quite fast (∼ 1 day), whereas basin-scale ocean circulation models tend to overestimate such decorrelation time because of finite resolution effects. Horizontal dispers...

Seismic fragility capacity of equipment--horizontal shaft pump test

International Nuclear Information System (INIS)

Iijima, T.; Abe, H.; Suzuki, K.

2005-01-01