Determination of dimethyl selenide and dimethyl sulphide compounds causing off-flavours in bottled mineral waters.

Science.gov (United States)

Guadayol, Marta; Cortina, Montserrat; Guadayol, Josep M; Caixach, Josep

2016-04-01

Sales of bottled drinking water have shown a large growth during the last two decades due to the general belief that this kind of water is healthier, its flavour is better and its consumption risk is lower than that of tap water. Due to the previous points, consumers are more demanding with bottled mineral water, especially when dealing with its organoleptic properties, like taste and odour. This work studies the compounds that can generate obnoxious smells, and that consumers have described like swampy, rotten eggs, sulphurous, cooked vegetable or cabbage. Closed loop stripping analysis (CLSA) has been used as a pre-concentration method for the analysis of off-flavour compounds in water followed by identification and quantification by means of GC-MS. Several bottled water with the aforementioned smells showed the presence of volatile dimethyl selenides and dimethyl sulphides, whose concentrations ranged, respectively, from 4 to 20 ng/L and from 1 to 63 ng/L. The low odour threshold concentrations (OTCs) of both organic selenide and sulphide derivatives prove that several objectionable odours in bottled waters arise from them. Microbial loads inherent to water sources, along with some critical conditions in water processing, could contribute to the formation of these compounds. There are few studies about volatile organic compounds in bottled drinking water and, at the best of our knowledge, this is the first study reporting the presence of dimethyl selenides and dimethyl sulphides causing odour problems in bottled waters. Copyright © 2016 Elsevier Ltd. All rights reserved.

Radioactivity in French bottled waters

Energy Technology Data Exchange (ETDEWEB)

Loyen, J.; Brassac, A.; Augeray, C.; Fayolle, C.; Gleizes, M. [Institut de Radioprotection et de Surete Nucleaire - IRSN (France)

2014-07-01

As IRSN is considered as a reference laboratory for radioactivity measurements, French health ministry and French nuclear safety authority asked IRSN to carry out a study in order to get a fresh and complete status of radiological water quality of French bottled waters. The study was carried out during 12 months in 2012. A total of 142 bottled waters samples were analyzed (75 spring waters and 67 natural mineral waters). The laboratories of IRSN were in charge of: - systematic measurement of radioactivity following requirements of the French health ministry (Circulaire du 13/06/2007) regarding the monitoring and management of sanitary risk linked to the presence of radionuclides in drinking waters (natural mineral waters excepted). - systematic uranium mass concentration determination; - a few radon-222 gas measurements for waters in glass bottles. This study is a flash assessment of radiological characteristics of French bottled waters, at the analysis date for the sample received. It was done in informative way and was not done for regulatory control purposes.. This study has shown that: - all bottled waters analyzed have a tritium activity concentration lower than the quality reference value of 100 Bq/l of the French regulation; - More than 105 bottled waters analyzed (80% of the springs waters and 70% of natural mineral waters received) have a gross alpha activity concentration lower than the guideline value of 0,1 Bq/l of the French regulation; - All bottled waters analyzed have a residual gross beta activity concentration lower than the guideline value of 1 Bq/l of the French regulation; - All bottled waters analyzed have a uranium mass concentration lower than the provisory guideline value of 30 μg/l of the WHO for drinking waters; - radon-222 was only significantly measured once upon 6 glass bottled waters with a value far below the reference value of 100 Bq/l of the future European Directive on drinking waters. For 32 bottled waters with gross alpha

Acid-base balance and hydration status following consumption of mineral-based alkaline bottled water

Directory of Open Access Journals (Sweden)

Heil Daniel P

2010-09-01

Full Text Available Abstract Background The present study sought to determine whether the consumption of a mineral-rich alkalizing (AK bottled water could improve both acid-base balance and hydration status in young healthy adults under free-living conditions. The AK water contains a naturally high mineral content along with Alka-PlexLiquid™, a dissolved supplement that increases the mineral content and gives the water an alkalizing pH of 10.0. Methods Thirty-eight subjects were matched by gender and self-reported physical activity (SRPA, hrs/week and then split into Control (12 women, 7 men; Mean +/- SD: 23 +/- 2 yrs; 7.2 +/- 3.6 hrs/week SRPA and Experimental (13 women, 6 men; 22 +/- 2 yrs; 6.4 +/- 4.0 hrs/week SRPA groups. The Control group consumed non-mineralized placebo bottled water over a 4-week period while the Experimental group consumed the placebo water during the 1st and 4th weeks and the AK water during the middle 2-week treatment period. Fingertip blood and 24-hour urine samples were collected three times each week for subsequent measures of blood and urine osmolality and pH, as well as total urine volume. Dependent variables were analyzed using multivariate repeated measures ANOVA with post-hoc focused on evaluating changes over time within Control and Experimental groups (alpha = 0.05. Results There were no significant changes in any of the dependent variables for the Control group. The Experimental group, however, showed significant increases in both the blood and urine pH (6.23 to 7.07 and 7.52 to 7.69, respectively, a decreased blood and increased urine osmolality, and a decreased urine output (2.51 to 2.05 L/day, all during the second week of the treatment period (P Conclusions Consumption of AK water was associated with improved acid-base balance (i.e., an alkalization of the blood and urine and hydration status when consumed under free-living conditions. In contrast, subjects who consumed the placebo bottled water showed no changes over the

A microbiological study of bottled mineral water marketed in Ludhiana.

Science.gov (United States)

Lal, M; Kaur, H

2006-01-01

The microbiological quality of bottled mineral water marketed in Ludhiana was examined, Twenty three brands were analyzed for presumptive coliform count by multiple tube tests, and E. coli count was confirmed by Eijkman test. Bacterial and fungal loads were tested by membrane filtration test. Out of 23 only one sample (4.4%) showed the presumptive coliform count to be 460 most probable number (MPN)l 1 00ml,and 1 was found to be positive when tested by Eijkman test for Ecoli. In the membrane filtration test three samples (13%) showed more than two types of bacteria. Different types of bacteria isolated included Bacillus sp (19/23). Pseudomonas spp (13123), Ecoli, Klebsiella sp and S.albus one each Fungi was isolated from five of twenty three. (22%) samples. Only one brand of mineral water was unfit for human consumption. The rest of the samples were contaminated with non pathogenic flora.

Investigation of Antimony Leaching from Bottles (PET into the Bottled Waters in Fars Province

Directory of Open Access Journals (Sweden)

Masoud Noshadi

2015-05-01

Full Text Available Polyethylene Terephthalate (PET is the most common material used in manufacturing mineral water bottles. Antimony trioxide (Sb2O3 used to form the PET containers may pollute water with their ingredients. In this research, graphite furnance atomic absorption spectrometry was used to investigate the effects of storage time (1 to 8 weeks, storage temperature (-20 to 80 °C, pH (6.3 to 8.3, exposure to sunlight, and UV radiation on leaching antimony from PET bottles into the mineral water of 15 bottled water brands available in Fars Province. Concentrations of antimony in the first and second weeks were lower than the maximum standard limit (5 ppb recommended by Iranian regulations. Antimony concentration in one sample (brand A rose above the standard limit after four weeks and in 3 samples (brands A, F, and J with antimony concentrations of 5.48, 5.08, and 5.06 µg/L, respectively exceeded the standard limit after 8 weeks. Sunlight, UV radiation, changes in pH, and storage at temperatures of -20 ℃, 60 ℃, and 80℃ were also found to increase antimony concentrations to levels above the maximum standard limit. Clearly, storing bottled mineral water in ambient conditions may lead to the release of antimony into bottled water, which is a serious threat to public health.

Natural mineral bottled waters available on the Polish market as a source of minerals for the consumers. Part 1. Calcium and magnesium.

Science.gov (United States)

Gątarska, Anna; Tońska, Elżbieta; Ciborska, Joanna

2016-01-01

Natural mineral waters may be an essential source of calcium, magnesium and other minerals. In bottled waters, minerals occur in an ionized form which is very well digestible. However, the concentration of minerals in underground waters (which constitute the material for the production of bottled waters) varies. In view of the above, the type of water consumed is essential. The aim of the study was to estimate the calcium and magnesium contents in products available on the market and to evaluate calcium and magnesium consumption with natural mineral water by different consumer groups with an assumed volume of the consumed product. These represented forty different brands of natural mineral available waters on Polish market. These waters were produced in Poland or other European countries. Among the studied products, about 30% of the waters were imported from Lithuania, Latvia, Czech Republic, France, Italy and Germany. The content of calcium and magnesium in mineral waters was determined using flame atomic absorption spectrometry in an acetylene-air flame. Further determinations were carried out using atomic absorption spectrometer--ICE 3000 SERIES-THERMO-England, equipped with a GLITE data station, background correction (a deuterium lamp) as well as other cathode lamps. Over half of the analysed natural mineral waters were medium-mineralized. The natural mineral waters available on the market can be characterized by a varied content of calcium and magnesium and a high degree of product mineralization does not guarantee significant amounts of these components. Among the natural mineral waters available on the market, only a few feature the optimum calcium-magnesium proportion (2:1). Considering the mineralization degree of the studied products, it can be stated that the largest percentage of products with significant calcium and magnesium contents can be found in the high-mineralized water group. For some natural mineral waters, the consumption of 1 litre daily may

A survey of the radiological quality of Mexican bottled waters

Energy Technology Data Exchange (ETDEWEB)

Lopez del R, H.; Davila R, J. I.; Rosales H, M. A.; Mireles G, F.; Pinedo V, J. L., E-mail: hlopezdelrio@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98060 Zacatecas (Mexico)

2013-10-15

More bottled drinking water is consumed per capita in Mexico than in any other country in the world. With the purpose of verifying the compliance with Mexican standards for radioactive content of drinking water, the gross alpha and beta activities were measured in 34 brands of bottled water consisting of purified water (19), natural mineral water (12), and mineralized water (3). Electrical conductivity of water samples ranged from 10 to 1465 μS/cm, and mostly high values were for the mineralized water samples. Gross alpha activities ranged from <12.2 to 709.8 mBq/L, while gross beta activities values varied from <26 to 616 mBq/L. All the bottled water samples had radioactivity content below the maximum permissible levels established in the Official Mexican Norm, except for the gross alpha level of one natural mineral water. Based upon these results it can be concluded that, in general, the analyzed bottled waters have acceptable quality with regard to radioactive content of gross alpha and beta activities. (Author)

A survey of the radiological quality of Mexican bottled waters

International Nuclear Information System (INIS)

Lopez del R, H.; Davila R, J. I.; Rosales H, M. A.; Mireles G, F.; Pinedo V, J. L.

2013-10-01

More bottled drinking water is consumed per capita in Mexico than in any other country in the world. With the purpose of verifying the compliance with Mexican standards for radioactive content of drinking water, the gross alpha and beta activities were measured in 34 brands of bottled water consisting of purified water (19), natural mineral water (12), and mineralized water (3). Electrical conductivity of water samples ranged from 10 to 1465 μS/cm, and mostly high values were for the mineralized water samples. Gross alpha activities ranged from <12.2 to 709.8 mBq/L, while gross beta activities values varied from <26 to 616 mBq/L. All the bottled water samples had radioactivity content below the maximum permissible levels established in the Official Mexican Norm, except for the gross alpha level of one natural mineral water. Based upon these results it can be concluded that, in general, the analyzed bottled waters have acceptable quality with regard to radioactive content of gross alpha and beta activities. (Author)

Trace elements and heavy metals in mineral and bottled drinking waters on the Iranian market.

Science.gov (United States)

Hadiani, Mohammad Rasoul; Dezfooli-Manesh, Shirin; Shoeibi, Shahram; Ziarati, Parisa; Mousavi Khaneghah, Amin

2015-01-01

A survey of Iranian waters, sampled from 2010 to 2013, is presented. A total of 128 water samples from 42 different brands of bottled mineral and drinking water were collected and analysed for contamination levels of lead (Pb), cadmium (Cd), copper (Cu), arsenic (As) and mercury (Hg). Determinations were performed using a graphite furnace atomic absorption spectrophotometer for Pb, Cd and Cu, a hydride vapour generation as well as an Arsenator digital kit (Wagtech WTD, Tyne and Wear, UK) for As and a direct mercury analyser for Hg. Arsenic concentration in six bottled gaseous mineral samples was higher than the related limit. Regardless of these, mean concentrations of Pb, Cd, Cu, As and Hg in all types of water samples were 4.50 ± 0.49, 1.08 ± 0.09, 16.11 ± 2.77, 5.80 ± 1.63 and 0.52 ± 0.03 µg L⁻¹, respectively. Values obtained for analysed heavy metals in all samples were permissible according to the limits of national and international standards.

Measurement of the 226Ra-concentration in bottled Austrian mineral waters and table beverages

International Nuclear Information System (INIS)

Friedmann, H.; Hernegger, F.

1978-01-01

226 Ra being regarded nowadays as a toxic trace element, a systementic examination of bottled Austrian mineral waters and table beverages has been carried out. Only in one case was the maximum allowable concentration of 3.3 pCi/l, a value set up by the WHO, clearly exceeded. (orig.) [de

The occurrence of Aeromonas spp. in the bottled mineral water, well water and tap water from the municipal supplies

Directory of Open Access Journals (Sweden)

Denise de Oliveira Scoaris

2008-10-01

Full Text Available The aim of this work was to study the occurrence of Aeromonas sp in the bottled mineral water, well water and tap water from the municipal supplies. Positive samples were found for Aeromonas spp. 12.7% from the mineral water, 8.3% from the artesian water and 6.5% from the tap water. The recovery of Aeromonas spp. was significantly higher in the bottled mineral and artesian water than in the tap water from municipal supplies. The occurrence of the Aeromonas spp. did not correlate significantly with the contamination indicator bacteria (i.e. total coliforms in the artesian water samples. However, a significant correlation was found between Aeromonas spp. and total coliforms in the both mineral water and tap water samples. The presence or absence of a correlation between the indicator bacteria and Aeromonas could reflect the occasional appearance of the pathogen in the drinking water and the different rates of survival and recovery of these agents compared with those fecal indicators. The finding that 41.6, 14.8 and 9.0 % of the artesian water, bottled mineral water and tap water, respectively, sampled in the current study failed to meet the Brazilian standard for total coliforms in the drinking water should therefore be of concern.A porcentagem de amostras positivas para Aeromonas foi de 12.7% para água mineral, 8.3% para água de poço artesiano e 6.5% para água do sistema público de abastecimento. O isolamento de Aeromonas spp. foi significativamente maior em água mineral e água de poço artesiano do que em água do sistema público. A ocorrência de Aeromonas spp. não teve correlação significativa com os indicadores de contaminação tradicionalmente utilizados (coliformes totais em amostras de água de poço artesiano. No entanto, esta correlação foi positiva e significativa em água mineral e água do sistema público. A presença ou ausência de correlação entre bactérias indicadoras e a presença de Aeromonas pode refletir o

226Ra and natural uranium in egyptian bottled mineral waters

International Nuclear Information System (INIS)

Higgy, R.H.

2000-01-01

Concentration levels of 226 Ra and natural uranium have been analysed bottled mineral water commercially available in egypt. 226 Ra was determined by applying a chemical procedure in which Ra was coprecipitated with Ba as sulphate. The precipitate was then dissolved with EDTA and then measured by liquid scintillation system, after mixing with a scintillation cocktail. Natural uranium was determined by applying a chemical procedure for uranium extraction using MIBK and then measured using laser fluorimeter system. The concentration values obtained were compared with concentrations reported by other countries and with reference values accepted for drinking water. Based on the consumption rate and the measured concentrations, the collective committed effective doses were calculated. In addition, Ca, Mg and Na were measured using Icp system and compared with some worldwide values

Measurement of natural radionuclides in Malaysian bottled mineral water and consequent health risk estimation

Science.gov (United States)

Priharti, W.; Samat, S. B.; Yasir, M. S.

2015-09-01

The radionuclides of 226Ra, 232Th and 40K were measured in ten mineral water samples, of which from the radioactivity obtained, the ingestion doses for infants, children and adults were calculated and the cancer risk for the adult was estimated. Results showed that the calculated ingestion doses for the three age categories are much lower than the average worldwide ingestion exposure of 0.29 mSv/y and the estimated cancer risk is much lower than the cancer risk of 8.40 × 10-3 (estimated from the total natural radiation dose of 2.40 mSv/y). The present study concludes that the bottled mineral water produced in Malaysia is safe for daily human consumption.

Radium activity measurements in bottled mineral water

International Nuclear Information System (INIS)

Kappke, Jaqueline; Paschuk, Sergei A.; Correa, Janine N.; Denyak, Valeriy; Reque, Marilson; Rocha, Paschuk; Rocha, Zildete; Santos, Talita O.

2011-01-01

This work presents the preliminary results of 226 Ra activity measurements of fifteen samples of bottled mineral water acquired at markets of Curitiba-PR, Brazil. The measurements were performed at the Laboratory of Applied Nuclear Physics of the Federal University of Technology - Parana (UTFPR) in collaboration with the Center of Nuclear Technology Development of Brazilian Nuclear Energy Committee (CNEN). The experimental setup was based on the electronic radon detector RAD7 (Durridge Company, Inc.). The measurements were carried out with a special kit of accessory vessels (vials) RAD7 H 2 O, which allows one to identify the 222 Rn activity concentration in small water samples of 40 mL and 250 mL in the range going from less than 30 pCi/L to greater than 10 5 pCi/L. During each measurement a vial from RAD H 2 O was poured with a sample of water. The air pump, included in the close loop aeration circuit and connected to the vial and RAD7 detector, operated for five minutes to snatch the sample of air maintained above the level of water sample and transporting it from the vial through the system. Evaluation of the concentration of soluble radium ( 226 Ra) salts in water and their activity was performed after 30 days when 222 Rn in the water samples reached secular equilibrium. The background measurements were performed using the samples of the distilled water. Considering the importance of background measurements, it was found that the value suggested by user Manual protocol (RAD7) for the case of low activity radon measurements, has to be slightly modified. (author)

The radioactivity of bottled mineral waters

International Nuclear Information System (INIS)

Vrakova, M.; Babarikova, F.; Belanova, A.

2005-01-01

Mineral waters with increased contents of minerals (total mineralization ranging from 1000 to 4000 mg.dm -3 ) can also contain increased concentrations of natural radionuclides. For this reason it is necessary to monitor radioactivity of mineral and thermal springs. Hundreds of springs which are used for drinking purposes are spread in many regions all over Slovakia. In our laboratory we determined these radionuclides in mineral waters: total alpha, total beta, volume activity 222 Rn, concentration of U nat , volume 226 Ra, 228 Ra and 210 Po. From values of determined volume activities of radionuclides we calculated total effective dose from reception mineral waters. By calculation of effective dose we supposed consumption of mineral water 150 dm 3 .year -1 (0.4 dm 3 .day -1 ) for adults (according to UNSCEAR). Conversion factors are initiated in the regulation of Ministry of Health of Slovak Republic (MZ SR No.12/2001). (authors)

Macro and microelements in bottled and tap waters of Serbia

Directory of Open Access Journals (Sweden)

Petrović Tanja M.

2012-01-01

Full Text Available Comparative analysis between bottled and tap waters as well as its comparison with current Serbian regulations, European Union Directives and World Health Organization standard are shown in this paper. Thirteen bottled waters and fourteen tap waters from the territory of Serbia were analyzed in the Federal Institute for Geosciences and Natural Resources (BGR laboratory in Berlin, for the purpose of the “Geochemistry of European Bottled Water“ project conducted by EuroGeo Survey Geochemistry (EGS. Macrocomponents (main cations and anions of ground waters usually reflect on lithogeochemistry of the aquifer, while microcomponents indicate the circulation of ground water through the different lithological environment. Analyzed bottled waters could be classified as those with low mineral content (M<500 mg/L if HCO3 anion and Ca and Mg cations were the prevailing ones, or mineral (M>500 mg/L with prevailing HCO3 anion and Na cation. Waters with low mineral content were mainly from limestone and dolomite, while mineral waters mainly originated from magmatic and metamorphic rocks. Higher content of Cs, Li, Ge, Rb and F in bottled waters indicates the importance of the magmatic intrusions influence on their chemical composition. In some waters higher content of B, I, NH4, as well as of Tl and W has been observed which can be attributed to water’s circulation through different lithological complexes. Tap water was mostly obtained from groundwater (from Neogen and alluvial aquifers and karst springs with rest being those of rivers and surface accumulations. Tap waters from Central Serbia were with low mineral content, with prevailing HCO3 anion and Ca and Mg cations, while waters from Vojvodina, the northern province of Serbia, were with higher mineralization, HCO3-Na. Chemical analyses of the sampled tap waters showed good quality, with exception of waters from the cities of Senta and Zrenjanin in Vojvodina. High values of B (1170 and 895 g/L, As

Changes in Isotopic Composition of Bottled Natural Waters Due to Different Storage Conditions

Energy Technology Data Exchange (ETDEWEB)

Ferjan, T. [Geological Survey of Slovenia, Department of Hydrogeology, Ljubljana (Slovenia); Brencic, M. [Faculty of Natural Sciences and Engineering, Department of Geology, and Geological Survey of Slovenia, Department of Hydrogeology, Ljubljana (Slovenia); Vreca, P. [Jozef Stefan Institute, Department of Environmental Sciences, Ljubljana (Slovenia)

2013-07-15

To establish the influence of environmental conditions on processes affecting the stable isotopic composition of bottled water during storage, various brands of bottled water were exposed for 2 years in different conditions. Selected low mineralized natural mineral water of one particular brand stored in polyethylene terephthalate (PET) bottles was placed at three different locations with different physical conditions (temperature, relative humidity, air pressure, exposure to sunlight). For comparison, bottles of three other low mineralized natural mineral water brands, each from a different aquifer source, were placed in parallel at one of the locations. Each location was characterized by temperature, relative humidity and air pressure measurements. pH, conductivity and stable isotopic composition of oxygen, hydrogen and carbon in dissolved inorganic carbon ({delta}{sup 18}O, {delta}{sup 2}H, {delta}{sup 13}C{sub DIC}) were measured in regular intervals for nearly two years. Preliminary results from each location show noticeable changes in isotopic composition as well as the physical parameters of water with time of storage.

Measurement of natural radionuclides in Malaysian bottled mineral water and consequent health risk estimation

Energy Technology Data Exchange (ETDEWEB)

Priharti, W.; Samat, S. B.; Yasir, M. S. [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor (Malaysia)

2015-09-25

The radionuclides of {sup 226}Ra, {sup 232}Th and {sup 40}K were measured in ten mineral water samples, of which from the radioactivity obtained, the ingestion doses for infants, children and adults were calculated and the cancer risk for the adult was estimated. Results showed that the calculated ingestion doses for the three age categories are much lower than the average worldwide ingestion exposure of 0.29 mSv/y and the estimated cancer risk is much lower than the cancer risk of 8.40 × 10{sup −3} (estimated from the total natural radiation dose of 2.40 mSv/y). The present study concludes that the bottled mineral water produced in Malaysia is safe for daily human consumption.

Water Quality Evaluation of PET Bottled Water by Mineral Balance in the Northeast Asian Region: A Case Study of South Korea.

Science.gov (United States)

Houri, Daisuke; Koo, Chung Mo

2015-09-01

The past few years have seen a demand for drinking water in contemporary society with a focus on safety and taste. Mineral water is now marketed as a popular commercial product and, partly due to health concerns, the production. For the study, a comparison was carried out of water samples from 9 types of polyethylene terephthalate (PET) bottled water sold in South Korea as well as from tap water in the cities of Seoul and Chuncheon. These were compared with samples of Japanese PET bottled water in order to determine shared commonalities and identify individual characteristics. To evaluate water quality objectively, we quantified the elements contained in the water samples. Samples were assessed not with the usual sensory evaluation but with the evaluation approach advocated by Hashimoto et al. which employs the Water Index of Taste and the Water Index of Health. The levels of water quality obtained were compared with the "Prerequisites for Tasty Water" and the "Standards for Tasty Water" devised for city water. The PET Bottled water varieties analyzed in this study-Seoksu, Icis, Bong Pyong, Soon Soo 100, Dong Won Saem Mul, GI JANG SOO and DIAMOND-showed the Water Index of Taste ≥ 2.0 and the Water Index of Health ≥ 5.2, which we classified as tasty/healthy water. SamDaSoo and NamiNeral can be classified as tasty water due to their values of the Water Index of Taste ≥ 2.0 and the Water Index of Health water studied here fulfills the "Water Index of Taste," "Water Index of Health," "Standard for Tasty Water" and "Prerequisites for Tasty Water" that Japanese people value for city water. We can conclude that bottled water which meets water quality requirements will be considered good-tasting by a majority of people.

Concentration of ions in selected bottled water samples sold in Malaysia

Science.gov (United States)

Aris, Ahmad Zaharin; Kam, Ryan Chuan Yang; Lim, Ai Phing; Praveena, Sarva Mangala

2013-03-01

Many consumers around the world, including Malaysians, have turned to bottled water as their main source of drinking water. The aim of this study is to determine the physical and chemical properties of bottled water samples sold in Selangor, Malaysia. A total of 20 bottled water brands consisting of `natural mineral (NM)' and `packaged drinking (PD)' types were randomly collected and analyzed for their physical-chemical characteristics: hydrogen ion concentration (pH), electrical conductivity (EC) and total dissolved solids (TDS), selected major ions: calcium (Ca), potassium (K), magnesium (Mg) and sodium (Na), and minor trace constituents: copper (Cu) and zinc (Zn) to ascertain their suitability for human consumption. The results obtained were compared with guideline values recommended by World Health Organization (WHO) and Malaysian Ministry of Health (MMOH), respectively. It was found that all bottled water samples were in accordance with the guidelines set by WHO and MMOH except for one sample (D3) which was below the pH limit of 6.5. Both NM and PD bottled water were dominated by Na + K > Ca > Mg. Low values for EC and TDS in the bottled water samples showed that water was deficient in essential elements, likely an indication that these were removed by water treatment. Minerals like major ions were present in very low concentrations which could pose a risk to individuals who consume this water on a regular basis. Generally, the overall quality of the supplied bottled water was in accordance to standards and guidelines set by WHO and MMOH and safe for consumption.

Quality status of bottled water brands in Pakistan

International Nuclear Information System (INIS)

Kahlown, M. A.; Tahir, M.A.

2005-01-01

The (PCRWR) has carried out a study to evaluate the quality of mineral water brands available in the market owing to demand of general public and consumer associations. Twenty one brands of bottled water were collected from Islamabad and Rawalpindi. Each water sample was analyzed for 24 aesthetic, physico-chemical and bacteriological water quality parameters by adopting standard analytical methods. It was observed that only 10 out of 21 brands (47.62%) were fit for drinking purpose. The remaining eleven brands (52.38%), including one imported brand, were found unsafe for human consumption. It was also concluded that present situation of water quality of bottled water is due to lack of legislation for water quality control. Hence there is a dire need for a legal organization to monitor and regulate the quality issues of bottled water industry. (author)

Determination of barium in natural waters by ICP-OES technique. Part II: Assessment of human exposure to barium in bottled mineral and spring waters produced in Poland.

Science.gov (United States)

Garboś, Sławomir; Swiecicka, Dorota

2013-01-01

A method of the classification of natural mineral and spring waters and maximum admissible concentration (MAC) levels of metals present in such types of waters are regulated by Commission Directive 2003/40/EC, Directive 2009/54/EC of the European Parliament and of the Council and Ordinance of Minister of Health of 30 March 2011 on the natural mineral waters, spring waters and potable waters. MAC of barium in natural mineral and spring waters was set at 1.0 mg/l, while World Health Organization determined the Ba guideline value in water intended for human consumption at the level of 0.7 mg/l. The aims of the study were: the determination of barium in natural mineral and spring waters (carbonated, non-carbonated and medium-carbonated waters) produced and bottled on the area of Poland, and assessment of human exposure to this metal presents in the above-mentioned types of waters. The study concerning barium determinations in 23 types of bottled natural mineral waters and 15 types of bottled spring waters (bought in Polish retail outlets) was conducted in 2010. The analyses were performed by validated method of determination of barium in water based on inductively coupled plasma optical emission spectrometry, using modern internal quality control scheme. Concentrations of barium determined in natural mineral and spring waters were in the ranges from 0.0136 mg/l to 1.12 mg/l and from 0.0044 mg/l to 0.43 mg/l, respectively. Only in the single case of natural mineral water the concentration of barium (1.12 mg/l), exceeded above-mentioned MAC for this metal, which is obligatory in Poland and the European Union - 1.0 mg/l. The long-term monitoring of barium concentration in another natural mineral water (2006 - 2010), in which incidental exceeding MAC was observed in 2006, was conducted. All measured barium concentrations in this water were lower than 1.0 mg/l and therefore, it is possible to state that the proper method of mixing waters taken from six independent

Radioactivity in bottled waters sold in Mexico

International Nuclear Information System (INIS)

Davila Rangel, J.I.; Lopez del Rio, H.; Mireles Garcia, F.; Quirino Torres, L.L.; Villalba, M.L.; Colmenero Sujo, L.; Montero Cabrera, M.E.

2002-01-01

Measurements of gross alpha and beta activities were made on 21 domestic and international brands of bottled (purified and mineral) water sold in the Mexican market to assess its radiological quality. Alpha and beta activities were determined using a liquid-scintillation detector with pulse-shape analysis feature. All the purified water had values of beta activity lower than the limit for potable drinking water (1.0 Bq/l), while three brands surpassed the limit of alpha activity (0.1 Bq/l). The limit for alpha radioactivity content was exceed by three mineral waters; the results show a correlation between radioactivity content and mineral salts, which are related with the origin and treatment of the waters

Relieving Dry Mouth: Varying Levels of pH Found in Bottled Water.

Science.gov (United States)

Fisher, Bailey Jean; Spencer, Angela; Haywood, Van; Konchady, Gayathri

2017-07-01

It is estimated that 30% of people older than 60 years suffer from hyposalivation or dry mouth. Drinking water frequently has been recommended as a safe, non-pharmacologic way to combat hyposalivation. The saliva in patients with dry mouth is acidic. Beverages consumed daily may have an erosive potential on teeth. The pH and the mineral content of the beverage determine its erosive potential. An acidic beverage, therefore, may have harmful effects on mineralized tooth structures, causing erosion of enamel, dentin, and cementum. Because bottled water is both convenient and easily available, the authors tested the pH of eight common brands of bottled water. (One brand included two different bottle types, for a total of nine bottled waters tested.) To standardize the pH electrode, pH buffers of 4.7 and 10 were used. The pH was measured using the Denver Instruments basic pH meter. Six recordings were used for each brand and then averaged to report the pH. Two of the bottled water samples tested were below the critical level of 5.2 pH to 5.5 pH, the level at which erosion of enamel occurs. Six of the samples tested were below the critical pH of 6.8, at which erosion of root dentin occurs. The authors conclude that both patients and clinicians incorrectly presume bottled water to be innocuous. Clinicians should be cognizant of the erosive potential of different brands of bottled water to both educate patients and to recommend water with neutral or alkaline pH for patients with symptoms of dry mouth to prevent further deterioration and demineralization of tooth structure.

Uranium, radium and 40K isotopes in bottled mineral waters from Outer Carpathians, Poland

International Nuclear Information System (INIS)

Kozlowska, B.; Walencik, A.; Dorda, J.; Przylibski, T.A.

2007-01-01

Radioactivity content in commercially bottled mineral waters from Outer Carpathians was investigated on the basis of 28 samples. Activity concentration results for radium isotopes 226,228 Ra, uranium isotopes 234,238 U and isotopic ratios 234 U/ 238 U were determined. The correlations between investigated isotopes and calculated potassium 40 K ions dissolved in water were carried out. The results show a correlation between TDS (total dissolved solids) values and dissolved radionuclides. High correlation coefficients were observed between total radium content and 40 K. The isotopic ratio of 234 U/ 238 U varies in the range from 1.6 to 7 in all investigated waters which means that there is no radioactive equilibrium between the parent nuclide 238 U and its daughter 234 U. The effective radiation dose coming from studied radium and uranium radionuclides consumed with mineral water from the Outer Carpathians obtained by a statistical Pole is equal to 4.3μSv/year (58 l/year water consumption) and do not exceed the permissible limit equal to 100μSv/year. Assuming 0.5 l consumption per day, i.e. 182.5 l/year, the effective dose is equal to 13.4μSv/year, what is still below the unit

Energy implications of bottled water

International Nuclear Information System (INIS)

Gleick, P H; Cooley, H S

2009-01-01

As bottled water use continues to expand around the world, there is growing interest in the environmental, economical, and social implications of that use, including concerns about waste generation, proper use of groundwater, hydrologic effects on local surface and groundwater, economic costs, and more. A key concern is how much energy is required to produce and use bottled water. This paper estimates the energy footprint required for various phases of bottled water production, transportation, and use. We do not develop a single comprehensive life-cycle energy estimate because of differences among water sources, bottling processes, transportation costs, and other factors, but we quantify key energy inputs necessary for site-specific assessments. We also apply these inputs to three site-specific examples of the energy required from production to the point of use: local bottled water produced and used in Los Angeles, water bottled in the South Pacific and shipped by cargo ship to Los Angeles, and water bottled in France and shipped in various ways to Los Angeles. For water transported short distances, the energy requirements of bottled water are dominated by the energy used to produce the plastic bottles. Long-distance transport, however, can lead to energy costs comparable to, or even larger than, those of producing the bottle. All other energy costs-for processing, bottling, sealing, labeling, and refrigeration-are far smaller than those for the production of the bottle and transportation. These data can be used to generate specific estimates for different sources, treatments, and delivery options.

Bottled drinking water: Water contamination from bottle materials (glass, hard PET, soft PET), the influence of colour and acidification

International Nuclear Information System (INIS)

Reimann, Clemens; Birke, Manfred; Filzmoser, Peter

2010-01-01

A test comparing concentrations of 57 chemical elements (Ag, Al, As, B, Ba, Be, Bi, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Er, Eu, Fe, Ga, Gd, Ge, Hf, Ho, I, K, La, Li, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Pb, Pr, Rb, Sb, Se, Sm, Sn, Sr, Ta, Tb, Te, Th, Ti, Tl, Tm, U, V, W, Y, Yb, Zn and Zr) determined by inductively coupled plasma quadrupole mass spectrometry (ICP-QMS) in 294 samples of the same bottled water (predominantly mineral water) sold in the European Union in glass and PET bottles demonstrates significant (Wilcoxon rank sum test, α = 0.05) differences in median concentrations for Sb, Ce, Pb, Al, Zr, Ti, Th, La, Pr, Fe, Zn, Nd, Sn, Cr, Tb, Er, Gd, Bi, Sm, Y, Lu, Dy, Yb, Tm, Nb and Cu. Antimony has a 21x higher median value in bottled water when sold in PET bottles (0.33 vs. 0.016 μg/L). Glass contaminates the water with Ce (19x higher than in PET bottles), Pb (14x), Al (7x), Zr (7x), Ti, Th (5x), La (5x), Pr, Fe, Zn, Nd, Sn, Cr, Tb (2x), Er, Gd, Bi, Sm, Y, Lu, Yb, Tm, Nb and Cu (1.4x). Testing an additional 136 bottles of the same water sold in green and clear glass bottles demonstrates an important influence of colour, the water sold in green glass shows significantly higher concentrations in Cr (7.3x, 1.0 vs. 0.14 μg/L), Th (1.9x), La, Zr, Nd, Ce (1.6x), Pr, Nb, Ti, Fe (1.3x), Co (1.3x) and Er (1.1x). One hundred and twenty-six bottles of three different materials (glass, hard PET and soft PET) in 5 principal colours (clear, light and dark green and blue, brown) were subsequently washed and then filled with high purity water (18.2 MΩ cm). A portion of the bottles where left at the original average pH of the water (pH 6.5) while the remaining bottles were acidified to pH 3.5 with HNO 3 . Concentrations of the same 57 elements as above were determined after 1, 2, 3, 4, 5, 15, 30, 56, 80 and 150 days of leaching. Results substantiate the observations from the direct comparison of the same water sold in different bottle types (colour). For most elements leaching is

Bottled Water Basics

Science.gov (United States)

Table of Contents Bottled water basics ....................................... pg.2 Advice for people with severely compromised immune systems (Sidebar) ............................. pg2 Know what you’re buying .............................. pg.3 Taste considerations ........................................ pg.4 Bottled water terms (Sidebar) ..................... pg.4 Begin by reading the ...

Water mineralization and its importance for health

OpenAIRE

N. Babio; C. Ferreira-Pêgo; F. Maraver Eyzaguirre; I. Vitoria Miñana; J. Salas-Salvadó

2016-01-01

Water mineralization and its importance for health La mineralización del agua y su importancia para la salud. Water is essential for life, participating in the metabolism of all the living organisms. In recent years, the consumption of tap water has decreased and the consumption of bottled water has increased worldwide. The mineral quality and composition of natural mineral water is known and constantly over the year, and their potential effects on health must be determined. Only magnes...

Production environment in mineral water plants; Mineral water kojo no seisan kankyo

Energy Technology Data Exchange (ETDEWEB)

Yoshimatsu, A. [Morinaga Engineering Company, Tokyo (Japan)

1996-01-05

This paper summarizes mineral waters as commercial products, and the manufacturing facilities thereof. The most widely used pattern of packaging mineral waters is to use either PET bottle or back-in box. The manufacturing process consists generally of: rough filtration of natural water, storage, activated carbon filtration, filtration, sterilization, ultrafine filtration, warm water bottling, capping, cooling, cartoning, storage, and shipment. The rough filtration removes sands. The activated carbon filtration removes water soluble organics. The sterilization is carried out under conditions of retaining the water at 75{degree}C for 15 seconds or retaining at 120 to 140{degree}C for 2 seconds. The ultrafine filtration uses a ceramic filter with a thickness of 0.2{mu}m. Sterilizing harmful microorganisms uses heating operation and filters to remove bacteria. An example may be cited that uses a bio-clean room for the purpose of controlling the harmful microorganisms. Subject microorganisms include a variety of viruses, rickettsia, bacteria, and fungi. The super-high performance (HEPA) filter used in the sterilization is demanded of collecting dusts with sizes of 0.3{mu}m or larger at a collection efficiency of 99.97% or higher. 3 refs., 4 figs., 1 tab.

Trace element analysis of mineral water samples by PIXE and ICP-MS

International Nuclear Information System (INIS)

Kennedy, V.John; Augusthy, A.; Varier, K. M.; Magudapathy, P.; Panchapakesan, S.; Nair, K.G.M.

1998-01-01

Trace elements present in bottled mineral water have been studied by PIXE and ICP-MS. Samples from ten different brands of brands of bottled mineral water were prepared by preconcentration techniques. Measurements were carried out using the 2 MeV proton beam obtained from 3 MV Tandem pelletron accelerator at the Institute of Physics, Bhubaneswar. Our results are compared with Indian standard packaged natural mineral water specifications, World Health Organisation (WHO) and European guidelines for drinking water standards. Concentration of aluminum was found to be more in one of the brands. In general, our results are comparable to the above standards. (author)

Fluoride Intake through Consumption of Tap Water and Bottled Water in Belgium

Directory of Open Access Journals (Sweden)

Herman van Oyen

2009-05-01

Full Text Available There is a tendency to align higher levels of fluoride in natural mineral water with the existing higher levels in tap water. Treatment of natural mineral waters could harm the preservation of their natural character. In this study fluoride intake through bottled and tap water consumption in the Belgian adult population was assessed, taking into account regional differences. A deterministic approach was used whereby consumption quantities of tap water and different brands of bottled water were linked with their respective fluoride concentrations. Data from the national food consumption survey (2004 were used and the Nusser methodology was applied to obtain usual intake estimates. Mean intake of fluoride through total water consumption in Flanders was 1.4±0.7 mg/day (97.5th percentile: 3.1 mg/day, while in the Walloon region it was on average 0.9±0.6 mg/day (97.5th percentile: 2.4 mg/day. The probability of exceeding the UL of 7 mg per day via a normal diet was estimated to be low. Consequently, there is no need to revise the existing norms, but higher fluoride concentrations should be more clearly indicated on the labels. Reliable data about total dietary fluoride intake in children, including intake of fluoride via tooth paste and food supplements, are needed.

21 CFR 165.110 - Bottled water.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Bottled water. 165.110 Section 165.110 Food and... CONSUMPTION BEVERAGES Requirements for Specific Standardized Beverages § 165.110 Bottled water. (a) Identity—(1) Description. Bottled water is water that is intended for human consumption and that is sealed in...

Natural uranium and 226Ra in bottled potable waters of Argentina

International Nuclear Information System (INIS)

Bomben, Ana M.; Palacios, Miguel A.

2001-01-01

This paper presents the results obtained of the measurement of the natural uranium and 226 Ra concentrations carried out on 345 drinking water samples coming from different provinces of Argentina. The samples were collected from tap water systems and private wells. Six bottled mineral waters samples, selected from those most extensively consumed, were also analyzed. The natural uranium concentration was determined by a fluorimetric procedure and 226 Ra by the 222 Rn emanation technique and liquid scintillation counting. Values ranging from 0,03 to 50 μg L -1 of natural uranium and concentrations up to 22 mBq L -1 were found in the drinking water samples analyzed. Natural uranium concentrations from 0,04 to 3,8 μg L -1 and 226 Ra concentrations up to 2,4 mBq L -1 were measured in the bottled mineral waters samples. Based on the water intake rate and the measured concentrations of both radionuclides analyzed, an annual collective effective dose of 1,5 man Sv and an average committed effective dose of 0,5 μSv a -1 , were calculated for the City of Buenos Aires inhabitants. (author)

Bottled Water: United States Consumers and Their Perceptions of Water Quality

OpenAIRE

Hu, Zhihua; Morton, Lois Wright; Mahler, Robert L.

2011-01-01

Consumption of bottled water is increasing worldwide. Prior research shows many consumers believe bottled water is convenient and has better taste than tap water, despite reports of a number of water quality incidents with bottled water. The authors explore the demographic and social factors associated with bottled water users in the U.S. and the relationship between bottled water use and perceptions of the quality of local water supply. They find that U.S. consumers are more likely to report...

Heavy Metals in Spring and Bottled Drinking Waters of Sibylline Mountains National Park (Central Italy).

Science.gov (United States)

Annibaldi, Anna; Illuminati, Silvia; Truzzi, Cristina; Scarponi, Giuseppe

2018-02-01

Heavy metal concentrations (cadmium, lead, and copper) in spring, tap, and bottled waters of the Sibylline Mountains National Park (central Italy) were investigated using square wave anodic stripping voltammetry from 2004 to 2011. The mean (±SD) concentrations detected (1.3 ± 0.4 ng L -1 cadmium, 14 ± 6 ng L -1 lead, and 0.16 ± 0.10 μg L -1 copper) were below the limits stipulated by Italian and European legislation for drinking and natural mineral water. In the three studied areas of the park (Mount Bove north, Mount Bove south, and springs of River Nera) with very few exceptions, both mineral waters bottled in the area and aqueduct waters from public fountains had approximately the same metal concentrations as did the spring waters from which they were derived. Conversely, substantially higher metal concentrations were found at some sites in private houses, which may be due to release of metals from old metal pipes. At the time of this study, waters of Sibylline Mountains National Park were of good quality, and no influence of the bottling process on heavy metal concentrations was found.

MAIN PROBLEMS AND PROSPECTS OF REPUBLIC OF BELARUS IN RESPECT OF ITS ENTRY TO INTERNATIONAL BOTTLED WATER MARKET

Directory of Open Access Journals (Sweden)

P. G. Nikitenko

2009-01-01

Full Text Available The Republic of Belarus has significant reserves of ground fresh and mineral water. Consumption of bottled water in the world has a tendency of steady growth. In this regard, Belarus can increase production and sale of bottled water on the external  and domestic markets as well. The paper  describes main tendencies prevailing on the world market;  it contains an analysis of the normative and legal foundation on regulation of production and sale of bottled water in the Republic and abroad; the paper also estimates the possibilities to increase volume of export water. 

Radiological quality of mineral waters battled in Tunisia

International Nuclear Information System (INIS)

Lemaitre, N.

2002-01-01

There are approximately 60 natural water springs in Tunisia, but only 10 of them, mostly in the north, are legally authorized to be sold for bottled mineral water. The object of this study is to determine the radiological content of the mineral waters bottled in Tunisia by calculating the annual effective dose resulting from ingestion of the natural radionuclides in these waters. The results show that radioactivity is relatively low in the Tunisian mineral waters and is due essentially to uranium and radium picked up as the water passes through the deep rocks. Levels measured range from 3.3 to 2.5 mBq/L for 234 U. Radium levels range from 2.0 to 67.0 mBq/L for 226 Ra and from 2.0 to 30.2 mBq/L for 228 Ra. These levels are lower than those measured in many other regions over the world. For daily mineral water consumption over one year, the estimated effective dose level varies between 0.006 and 0.091 mSv for an adult and between 0.008 and 0.107 mSv for a 5-year old child. These results do not present a public health risk in Tunisia. This investigation enabled us to assess the contribution of bottler water to radiological exposure of natural origins. (author)

Some mineral profiles of fresh and bottled palm wine – a ...

African Journals Online (AJOL)

Some mineral profiles of fresh palm wine and those of seven brands of bottled palm wine were analysed using atomic absorption spectroscopy and the values were compared. Three of the bottled samples contained toxic levels of either Pb or Cd or both. Neither metal was detected in fresh palm wine. Zn, Cr and Ni were 2 to ...

Chemical quality of bottled mineral waters from markets of Curitiba-PR-Brazil

Directory of Open Access Journals (Sweden)

Éder José dos Santos

Full Text Available ABSTRACT Twenty-seven bottled mineral waters from local markets in Curitiba, State of Paraná, Brazil were analyzed for a number of constituents, including: pH, conductivity, total dissolved solids, hardness, HCO3 - and CO 3 2-, as well as Ca2+, Mg2+, Na+, K+, NH4 + , F-, Cl-, NO3 -, NO2 - and SO4 2- by ion chromatography (IC; Al, Ba, Cd, Cr, Cu, Fe, Li, Mn, Ni, Sr, V and Zn by inductively coupled plasma optical emission spectrometry (ICP OES; Hg by cold vapor generation-ICP OES and As, Pb, Sb and Se by ICP-mass spectrometry (ICP-MS. The obtained limits of quantitation (LOQ were adequate for the determination of all analytes using the various analytical techniques. Results for the analysis of AccuStandard certified reference materials QCS-01-5, QCS-02-R1-5 and TCLP-02-1 as well as spike recoveries to samples show acceptable values, within 90-111 % of expected concentrations with relative standard deviations below 10 %, demonstrating the accuracy of the determinations. Both NO2 - and NO 3 - were above the maximum limits set by Brazilian legislation in two samples, indicating a microbiological contamination. One imported sample presented As (6.1 ± 0.2 µg L-1 near the maximum limit (10 µg L-1 while all other elements of interest were below the values specified by Brazilian legislation. Principal component analysis revealed that four imported samples and one from the Minas Gerais State have the highest mineral concentrations.

Hydrogeochemical approach to estimate the quality of bottled waters in Serbia

Directory of Open Access Journals (Sweden)

Ćuk Marina D.

2016-01-01

Full Text Available Bottled waters were analyzed for different chemical parameters and activity concentrations of radionuclides. The hydrocarbonate ion was dominant in all samples, while the major cation composition was a combination of Ca-Mg-Na ions. Physicochemical properties of bottled water samples are influenced by underlying geology. The sum of trace element concentrations varied from 79.7 to 9349.7 μg/l. The Dietary Reference Intake (DRI system was applied and contributions of some essential elements were calculated according to age group and gender. Hierarchical Cluster Analysis (HCA grouped bottled water samples into four clusters based on the similarities of the groundwater quality and essential elements concentrations. The origin of radioactivity is natural and could be traced to minerals in felsic igneous rocks. Two brands exhibited elevated beta activity (1.087±0.134 Bq/l; 1.242±0.146 Bq/l. Effective doses were found to be below the reference level of 0.1 mSv/yr. [Projekat Ministarstva nauke Republike Srbije, br. III 43004

Natural mineral waters: chemical characteristics and health effects

Science.gov (United States)

Quattrini, Sara; Pampaloni, Barbara; Brandi, Maria Luisa

2016-01-01

Summary Water contributes significantly to health and a daily intake of 1.5 to 2 liters of water should be guaranteed, because a good hydration is essential to maintain the body water equilibrium, although needs may vary among people. However, worldwide population is far from the Recommended Allowance for water intake. Among the waters for human uses, there are ‘waters (treated or not), intended for drinking, used for the food and beverages preparation or for other domestic purposes’ and natural mineral waters, that are ‘originated from an aquifer or underground reservoir, spring from one or more natural or bore sources and have specific hygienic features and, eventually, healthy properties’. According to the European Legislation (2009/54/EC Directive), physical and chemical characterization is used to make a classification of the different mineral waters, basing on the analysis of main parameters. Mineral composition enables to classify natural mineral waters as bicarbonate mineral waters, sulphate mineral waters, chloride mineral waters, calcic mineral waters, magnesiac mineral waters, fluorurate mineral waters, ferrous mineral waters and sodium-rich mineral waters. Although the concerns about bottled mineral waters (due to plasticizers and endocrine disruptors), many are the health effects of natural mineral waters and several studies explored their properties and their role in different physiological and pathological conditions. PMID:28228777

Quality Assurance for Iraqi Bottled Water Specifications

Directory of Open Access Journals (Sweden)

May George Kassir

2015-10-01

Full Text Available In this research the specifications of Iraqi drinking bottled water brands are investigated throughout the comparison between local brands, Saudi Arabia and the World Health Organization (WHO for bottled water standard specifications. These specifications were also compared to that of Iraqi Tap Water standards. To reveal variations in the specifications for Iraqi bottled water, and above mentioned standards some quality control tools are conducted for more than 33% of different bottled water brands (of different origins such as spring, purified,..etc in Iraq by investigating the selected quality parameters registered on their marketing labels. Results employing Minitab software (ver. 16 to generate X bar, and Pareto chart. It was found from X bar charts that the quality parameters of some drinking bottled water brands are not within Iraqi standards set by the “Central Agency for Standardization and Quality Control” such as pH values, Fe, Na, and Mg concentrations. While the comparison of previously mentioned standard specifications through radar chart many important issues are detected such as the absence of lower limits the whole bottled water quality parameters such as for Na and Mg also the radar chart shows that Iraqi bottled and tap water specifications are almost equal in their quality values. Also the same chart pictured the limited range of Iraqi specifications compared to that of Saudi Arabia, and WHO and the need to introduce other water specifications such as K, Na, etc. This confirms the need to improve Iraqi bottled water specifications since it was introduced on 2000. These results also highlighted the weakness of quality assurance activities since only 33 % of the investigated companies registered the whole water quality specifications as shown in Pareto chart. Other companies do not register any quality characteristics. Also certain companies should be stopped due to non-conforming specifications, yet these companies are

21 CFR 880.6085 - Hot/cold water bottle.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hot/cold water bottle. 880.6085 Section 880.6085... Devices § 880.6085 Hot/cold water bottle. (a) Identification. A hot/cold water bottle is a device intended for medical purposes that is in the form of a container intended to be filled with hot or cold water...

Comparison of different concentration methods for the detection of hepatitis A virus and calicivirus from bottled natural mineral waters

DEFF Research Database (Denmark)

Di Pasquale, S.; Paniconi, M; Auricchio, B

2010-01-01

To evaluate the efficiency of different recovery methods of viral RNA from bottled water, a comparison was made of 2 positively and 2 negatively charged membranes that were used for absorbing and releasing HAV virus particles during the filtration of viral spiked bottled water. All the 4 membrane...

Calcite precipitates in Slovenian bottled waters.

Science.gov (United States)

Stanič, Tamara Ferjan; Miler, Miloš; Brenčič, Mihael; Gosar, Mateja

2017-06-01

Storage of bottled waters in varying ambient conditions affects its characteristics. Different storage conditions cause changes in the initial chemical composition of bottled water which lead to the occurrence of precipitates with various morphologies. In order to assess the relationship between water composition, storage conditions and precipitate morphology, a study of four brands of Slovenian bottled water stored in PET bottles was carried out. Chemical analyses of the main ions and measurements of the physical properties of water samples were performed before and after storage of water samples at different ambient conditions. SEM/EDS analysis of precipitates was performed after elapsed storage time. The results show that the presence of Mg 2+ , SO 4 2- , SiO 2 , Al, Mn and other impurities such as K + , Na + , Ba and Sr in the water controlled precipitate morphology by inhibiting crystal growth and leading to elongated rhombohedral calcite crystal forms which exhibit furrowed surfaces and calcite rosettes. Different storage conditions, however, affected the number of crystallization nuclei and size of calcite crystals. Hollow calcite spheres composed of cleavage rhombohedrons formed in the water with variable storage conditions by a combination of evaporation and precipitation of water droplets during high temperatures or by the bubble templating method.

Physical, chemical and microbial analysis of bottled drinking water.

Science.gov (United States)

Sasikaran, S; Sritharan, K; Balakumar, S; Arasaratnam, V

2012-09-01

People rely on the quality of the bottled drinking water, expecting it to be free of microbial contamination and health hazards. To evaluate the quality of bottled drinking water sold in Jaffna peninsula by analysing the physical, chemical and microbial contents and comparing with the recommended Sri Lankan Standard (SLS) values. All bottled water samples sold in Jaffna peninsula were collected. Electrical conductivity, total dissolved solid, pH, calcium, nitrate, total aerobic and anaerobic count, coliform bacterial count and faecal contamination were checked. These are 22 brands of bottled drinking water sold in Jaffna peninsula. The sample had very low electrical conductivity when compared with SLS (750 μS/ cm) and varied from 19 to 253 μS/cm with the mean of 80.53 (±60.92) μS/cm. The pH values of the bottled drinking water brands varied from 4.11 to 7.58 with a mean of 6.2 (±0.75). The total dissolved solid content of the bottled drinking water brands varied from 9 to 123.67 mg/l with a mean of 39.5 (±30.23) mg/l. The calcium content of the bottled drinking water brands varied from 6.48 to 83.77 mg/l with a mean of 49.9 (±25.09) mg/l. The nitrate content of the bottled drinking water brands varied from 0.21 to 4.19 mg/l with the mean of 1.26 (±1.08) mg/l. Aerobic bacterial count varied from 0 to 800 colony forming unit per ml (cfu/ml) with a mean of 262.6 (±327.50) cfu/ml. Among the 22 drinking bottled water brands 14 and 9% of bottled drinking water brands showed fungal and coliform bacterial contaminants respectively. The water brands which contained faecal contamination had either Escherichia coli or Klebsiella spp. The bottled drinking water available for sale do not meet the standards stipulated by SLS.

Natural radionuclides in Austrian bottled mineral waters

International Nuclear Information System (INIS)

Gabriele Wallner; Tania Jabbar

2010-01-01

All commercially available mineral waters of Austrian origin were investigated with regard to the natural radionuclides 228 Ra, 226 Ra, 210 Pb, 210 Po, 238 U and 234 U. From 1 to 1.5 L of sample the nuclides were extracted and measured sequentially: the radium isotopes as well as 210 Pb were measured by liquid scintillation counting after separation on a membrane loaded with element-selective particles (Empore Radium Disks), 210 Po was determined by α-particle spectroscopy after spontaneous deposition onto a copper planchette and uranium was determined also by α-particle spectroscopy after anion separation and microprecipitation with NdF 3 . The calculated committed effective doses for adults, teens and babies were compared to the total indicative dose of 0.1 mSv/year given in the EC Drinking Water Directive. The dominant portion of the committed effective dose was due to 228 Ra. Highly mineralised waters showed also higher 226 Ra and 228 Ra levels. (author)

Collaborative validation of a rapid method for efficient virus concentration in bottled water

DEFF Research Database (Denmark)

Schultz, Anna Charlotte; Perelle, Sylvie; Di Pasquale, Simona

2011-01-01

. Three newly developed methods, A, B and C, for virus concentration in bottled water were compared against the reference method D: (A) Convective Interaction Media (CIM) monolithic chromatography; filtration of viruses followed by (B) direct lysis of viruses on membrane; (C) concentration of viruses......Enteric viruses, including norovirus (NoV) and hepatitis A virus (HAV), have emerged as a major cause of waterborne outbreaks worldwide. Due to their low infectious doses and low concentrations in water samples, an efficient and rapid virus concentration method is required for routine control...... by ultracentrifugation; and (D) concentration of viruses by ultrafiltration, for each methods' (A, B and C) efficacy to recover 10-fold dilutions of HAV and feline calicivirus (FCV) spiked in bottles of 1.5L of mineral water. Within the tested characteristics, all the new methods showed better performance than method D...

Running Mechanics and Metabolic Responses with Water Bottles and Bottle Belt Holders.

Science.gov (United States)

Vincent, Heather K; Zdziarski, Laura A; Fallgatter, Kyle; Negron, Giorgio; Chen, Cong; Leavitt, Trevor; Horodyski, MaryBeth; Wasser, Joseph G; Vincent, Kevin R

2018-01-18

This study determined whether differential kinematics, kinetics, rates of energy use and cardiopulmonary responses occurred during running with water bottles and bottle belt holders compared to running only. Trained runners (N=42; 27.2±6.4 yr) ran on an instrumented treadmill for four conditions in a randomized order: 1) control run (CON); 2) hand-held full water bottle (FULL, 16.9 fluid oz; 454 g); 3) hand-held half-full water bottle (HALF, 8.4 fluid oz.; 227 g); and 4) waist-worn bottle belt holder (BELT; hydration belt; 676 g). Gas exchange was measured using a portable gas analyzer. Kinetic and kinematic responses were determined via standard 3D videographic techniques. Interactions of limb side (right, left) by study condition (CON, FULL, HALF, BELT) were tested for rates of oxygen use and energy expenditure, and kinematic and kinetic parameters. No significant limb side × condition interactions existed for rates of oxygen use or energy expenditure. A significant interaction occurred with sagittal elbow flexion (pwater by hand or on the waist does not significantly change kinematics of running motion, rates of oxygen use and energy expenditure or cardiopulmonary measures over short durations. Runners are likely making adjustments to joint moments and powers that preserve balance and protect the lower extremity joints while maintaining the rates of oxygen use and energy expenditure.

Bottled water, spas, and early years of water chemistry

Science.gov (United States)

Back, William; Landa, Edward R.; Meeks, Lisa

1995-01-01

Although hot springs have been used and enjoyed for thousands of years, it was not until the late 1700s that they changed the course of world civilization by being the motivation for development of the science of chemistry. The pioneers of chemistry such as Priestley, Cavendish, Lavoisier, and Henry were working to identify and generate gases, in part, to determine their role in carbonated beverages. In the 18th century, spas in America were developed to follow the traditional activities of popular European spas. However, they were to become a dominant political and economic force in American history on three major points: (1) By far the most important was to provide a place for the leaders of individual colonies to meet and discuss the need for separation from England and the necessity for the Revolutionary War; (2) the westward expansion of the United States was facilitated by the presence of hot springs in many locations that provided the economic justification for railroads and settlement; and (3) the desire for the preservation of hot springs led to the establishment of the National Park Service. Although mineral springs have maintained their therapeutic credibility in many parts of the world, they have not done so in the United States. We suggest that the American decline was prompted by: (1) the establishment of The Johns Hopkins School of Medicine in 1893; (2) enactment of the Pure Food and Drug Act of 1907; and (3) the remarkable achievement of providing safe water supplies for American cities by the end of the 1920s. The current expanding market for bottled water is based in part on bottled water being an alternative beverage Ito alcohol and sweetened drinks and the inconsistent palatability and perceived health hazards of some tap waters.

Fluoride Content of Bottled Drinking Waters in Qatar.

Science.gov (United States)

Almulla, Hessa Ibrahim; King, Nigel M; Alnsour, Hamza Mohammad; Sajnani, Anand K

2016-12-01

Fluoridation of drinking water has been recognized as one of the most effective ways of achieving community-wide exposure to the caries prevention effects of fluoride (F). A vast majority of people in Qatar use bottled water for drinking. Use of bottled water without knowing the F level may expose children to dental caries risk if the F level is lower than optimal or to dental fluorosis if the F level is too high. The aim of this study was to determine the F concentration of bottled water available in Qatar. A total of 32 brands of bottled water were evaluated. The F concentrations displayed on the labels were recorded. The F ion-selective electrode method was used to measure the F concentration in water samples, and three measurements were taken for every sample to ensure reproducibility. The p value was set at 0.05. The F concentration ranged from 0.06 to 3.0 ppm with a mean value of 0.8 ppm (±0.88). The F levels were provided by the manufacturers on the labels of 60 % of the samples, but this was significantly lower than the measured F levels (p < 0.0001). Moreover, bottled water that was produced in Saudi Arabia had significantly higher levels of F when compared to those produced in other countries (p < 0.05). There was a wide variation in the F levels in the different brands of bottled water. Furthermore, there was a significant disparity between the F levels which were measured and those that were provided on the labels.

Natural radionuclides in some romanian medicinal mineral water

Energy Technology Data Exchange (ETDEWEB)

Botezatu, E.; Iacob, O. [Institute of Public Health, Iasi (Romania)

2006-07-01

Radioactive minerals occur irregularly in the bedrock, similar to other minerals and they dissolve easily in water. Bedrock contains naturally occurring radioactivity including uranium, thorium, radium and potassium. The natural radioactivity results from water passing through deposits of naturally occurring radioactive materials.Many mineral water springs are traditionally used as drinking mineral water sources in the area.During the period from 1997 to 2000, we accomplished a study that had as basic objectives the radioacty control of the drinking mineral waters according to existing standards and evaluation of doses to population by ingestion of mineral water (bottled waters commercially available for human intake and some spring waters).For this reason, we were interested in finding out the extent to which these waters can be a natural radiation source. This survey aimed at assessing the radioactive content of these waters and their contribution to the population exposure.The presented data contribute to a national database concerning the natural radioactive content of Romanian mineral waters. A hypothetical person that undergoes a cure of mineral water by ingestion, inhalation and immersion is receiving an average supplementary dose of 3 {mu}Sv over background radiation of 2,512 {mu}Sv.y{sup -1} due to all natural radiation sources in Romania. The contribution of mineral water used in therapeutic purposes to the natural irradiation of population is very slight, almost insignificant. This supports the conclusion that these spring mineral waters can be used without any restrictions for drinking or bathing / washing for medical therapy of ailing persons even other sources of exposure are also taken into account. (N.C.)

A parallel analysis of hydrolithospheric beds geodata of Narzan mineral water Kislovodsk deposit

Directory of Open Access Journals (Sweden)

Д. А. Первухин

2016-11-01

Full Text Available The area of the Caucasus Mineral Waters – an environmental spa - occupies a special place among the other  spa regions of Russia due to richness, diversity, abundance and value of its mineral waters, landscape and climate conditions, and therapeutic muds. Lately the rate increased of developing its mineral water resources for both the local spa use and bottling for retail consumers. The growing number of mineral water bottling enterprises and sanatorium organizations affects significantly the amount of mineral water uptake. Irrational water uptake results in deterioration of underground water quality, change of its chemical composition and temperature. Expansion of the depression crater may eventually result in a collapse of seams roofing and vanishing of many water springs. It refers to all the waters underlying the area of Kavkazskie Mineralnye Vody. Due to that situation there is a potential threat of degradation of these deposits of mineral waters. Therefore, an important task consists in building forecast models of hydro-lithospheric processes in the region while the scope of water uptake changes in various parts of the deposit. it will be based on analyzing aerial photographs taken from board unmanned aerial vehicles. Currently such analysis is conducted using simple linear algorithms. The paper suggests to use the Nvidia CUDA technology for the purpose, adapting the mathematics used to ana- lyze aerial photographs to that technology. The initial data for processing were obtained by aerial photography in the course of remote sensing of the area by unmanned aerial vehicles belonging to OJSC «Narzan», Kislovodsk, an enterprise for mining mineral water. Presented in this paper have their Author’s Certificates issued by the Federal Institute of Industrial Property, the Russian Federation.

The switch to refillable bottled water in Indonesia: a serious health risk.

Science.gov (United States)

Komarulzaman, Ahmad; de Jong, Eelke; Smits, Jeroen

2017-10-01

In recent years, the consumption of refillable bottled water has increased considerably in emerging countries. However, the quality of this water is often questionable, as authorities lack the capacity to properly check refilling depots. Given that refillable bottled water not only replaces unimproved water sources, but also better-quality sources, like piped and branded bottled water, its increasing use poses a major health risk. We investigate the motives behind the decision to switch to refillable bottled water in Indonesia. Findings indicate that this switch is driven by lifestyle motives, as well as by cost and availability considerations. It is mostly the young affluent households who switch from piped and 'other' sources to refillable bottled water. In rural areas, the tendency to make this switch is negatively affected by availability problems and the higher price of refillable bottled water. Availability and cost also influence the switch from branded bottled to refillable bottled water, but here it is the poorer households who have a higher propensity to switch. Further exploration of the lifestyle motive and affordability issues, as well as better monitoring of the refilling depots, are needed to improve the quality of drinking water in Indonesia and other emerging countries.

What's Wrong with the Tap? Examining Perceptions of Tap Water and Bottled Water at Purdue University

Science.gov (United States)

Saylor, Amber; Prokopy, Linda Stalker; Amberg, Shannon

2011-09-01

The environmental impacts of bottled water prompted us to explore drinking water choices at Purdue University, located in West Lafayette, IN. A random sample of 2,045 Purdue University students, staff, and faculty was invited to participate in an online survey. The survey assessed current behaviors as well as perceived barriers and benefits to drinking tap water versus bottled water. 677 surveys were completed for a response rate of 33.1%. We then conducted qualitative interviews with a purposive sample of university undergraduates ( n = 21) to obtain contextual insights into the survey results and the beliefs of individuals with a variety of drinking water preferences. This study revealed that women drink disproportionately more bottled water then men while undergraduate students drink more than graduate students, staff and faculty. The study also uncovered a widespread belief that recycling eliminates the environmental impacts of bottled water. Important barriers to drinking tap water at Purdue include: perceived risks from tap water and the perceived safety of bottled water, preferring the taste of bottled water, and the convenience of drinking bottled water. The qualitative interviews revealed that drinking water choices can be influenced by several factors—especially whether individuals trust tap water to be clean—but involve varying levels of complexity. The implications of these results for social marketing strategies to promote tap water are discussed.

Salt Content in Ready-to-Eat Food and Bottled Spring and Mineral Water Retailed in Novi Sad.

Science.gov (United States)

Paplović, Ljiljana B Trajković; Popović, Milka B; Bijelović, Sanja V; Velicki, Radmila S; Torović, Ljilja D

2015-01-01

Salt intake above 5 g/person/day is a strong independent risk factor for hypertension, stroke and cardiovascular diseases. Published studies indicate that the main source of salt in human diet is processed ready-to-eat food, contributing with 65-85% to daily salt intake. The aim of this paper was to present data on salt content of ready-to-eat food retailed in Novi Sad, Serbia, and contribution of the salt contained in 100 g of food to the recommended daily intake of salt for healthy and persons with cardiovascular disease (CVD) risk. In 1,069 samples of ready-to-eat food, salt (sodium chloride) content was calculated based on chloride ion determined by titrimetric method, while in 54 samples of bottled water sodium content was determined using flame-photometry. Food items in each food group were categorized as low, medium or high salt. Average salt content of each food group was expressed as a percentage of recommended daily intake for healthy and for persons with CVD risk. Average salt content (g/100 g) ranged from 0.36 ± 0.48 (breakfast cereals) to 2.32 ± 1.02 (grilled meat). The vast majority of the samples of sandwiches (91.7%), pizza (80.7%), salami (73.9%), sausages (72.9%), grilled meat (70.0%) and hard cheese (69.6%) had a high salt profile. Average amount of salt contained in 100 g of food participated with levels ranging from 7.2% (breakfast cereals) to 46.4% (grilled meat) and from 9.6% to 61.8% in the recommended daily intake for healthy adult and person with CVD risk, respectively. Average sodium content in 100 ml of bottled spring and mineral water was 0.33 ± 0.30 mg and 33 ± 44 mg, respectively. Ready-to-eat food retailed in Novi Sad has high hidden salt content, which could be considered as an important contributor to relatively high salt consumption of its inhabitants.

[Mineral waters from several Brazilian natural sources].

Science.gov (United States)

Rebelo, M A; Araujo, N C

1999-01-01

To divulge information on the chemical composition and physical-chemical features of some mineral waters from Brazilian natural sources that will be of useful protocol investigation and patient advice. The survey was based on bottle labels of non-gaseous mineral waters commercially available in the city of Rio de Janeiro. The íon concentration of each mineral was calculated from the salt content. 36 springs were enralled from different states of the country. The pH (25 degrees C), 4.1 to 9.3, varied on dependence of the source and it was linearey correlated with the cations calcium, magnesium and sodium and the anion bicarbonate. It was atributed to high alkalinity (about 70% of bicarbonate in the molecula-gram) of these salts. The calcium (0.3 to 42 mg/l), magnesium (0.0 to 18 mg/l) and bicarbonate (4 to 228 mg/l) contents are relatively low. The mineral content of the Brazilian springs enrolled in this survey is low; about 70% of the sources having calcium and magnesium less than 10 mg/l and 1.0 mg/l, respectively, similar to local tap water.

Bottled Water Everywhere: Keeping it Safe

Science.gov (United States)

... that taps an aquifer—layers of porous rock, sand, and earth that contain water—which is under ... it to be labeled as “purified water.” Ensuring Quality and Safety Federal quality standards for bottled water ...

Bacteriological quality of bottled water sold on the Ghanaian market ...

African Journals Online (AJOL)

Bacteriological quality of bottled water sold on the Ghanaian market. ... Consumption of bottled water is increasing rapidly in developing countries especially among ... limits set by WHO guidelines and therefore safe for human consumption.

Evaluation of Microbial Quality of Bottled Water in Iran

Directory of Open Access Journals (Sweden)

Mahmood Alimohammadi

2014-03-01

Full Text Available Background: Because of population growth, limited access to fresh water resources, the need to use bottled water, controlling microbial quality of  bottled water is important. Materials and Methods: Microbiological quality of 24 brands of bottled water available in the town markets of Iran was studied Random. Samples were collected in summer and autumn, 2012. In each season, we collected two samples for each brand. In order to analyze Total coliforms, E-Coli, and HPC, MPN and Plate Count Methods were used. Data analysis was processed by SPSS software. Results: Total coliforms were 2 MPN/100CC in two brands S18 and S20. Increased HPC levels were also observed in all brands. pH level of 6% from bottled waters were higher than the standard. Average of turbidity was 0.232 and 0.228 at the autumn and summer, respectively. Conclusion: the heterotrophic microorganisms were present in 100% of the samples. Total coliforms were also found in 12% of the samples. None of the samples contained E-Coli.

Risk Factors Associated with the Choice to Drink Bottled Water and Tap Water in Rural Saskatchewan

Directory of Open Access Journals (Sweden)

Lianne McLeod

2014-01-01

Full Text Available A cross-sectional study investigated risk factors associated with choices to drink bottled water and tap water in rural Saskatchewan. Of 7,500 anonymous postal questionnaires mailed out, 2,065 responses were analyzed using generalized linear mixed models. Those who reported a water advisory (p < 0.001 or living in the area for £10 years (p = 0.01 were more likely to choose bottled water. Those who reported tap water was not safe to drink were more likely to choose bottled water, an effect greater for those who had no aesthetic complaints (p ≤ 0.001, while those with aesthetic complaints were more likely to choose bottled water if they believed the water was safe (p < 0.001. Respondents who treated their water and did not use a community supply were more likely to choose bottled water (p < 0.001, while those who did not treat their water were more likely to choose bottled water regardless of whether a community supply was used (p < 0.001. A similar pattern of risk factors was associated with a decreased likelihood of consuming tap water daily; however, the use of a community water supply was not significant. Understanding the factors involved in drinking water choices could inform public health education efforts regarding water management in rural areas.

Quality characteristics of commercial bottled water sold in Owerri ...

African Journals Online (AJOL)

The quality characteristics of commercial bottled water sold in Owerri, Imo State, Nigeria were investigated to determine their physical, chemical and bacteriological content. The four brands of bottled water investigated were Mevok ®, Ozonized April ®, Lacrystal ® and Eva ®. The mean turbidity value of all the samples were ...

Hazards of Healthy Living: Bottled Water and Salad Vegetables as Risk Factors for Campylobacter Infection

Science.gov (United States)

Ribeiro, C. Donald; Salmon, Roland L.

2003-01-01

Campylobacter is the most common cause of bacterial gastroenteritis worldwide, yet the etiology of this infection remains only partly explained. In a retrospective cohort study, we compared 213 sporadic campylobacter case-patients with 1,144 patients with negative fecal samples. Information was obtained on food history, animal contact, foreign travel, leisure activities, medical conditions, and medication use. Eating chicken, eating food from a fried chicken outlet, eating salad vegetables, drinking bottled water, and direct contact with cows or calves were all independently associated with infection. The population-attributable fractions for these risk factors explained nearly 70% of sporadic campylobacter infections. Eating chicken is a well-established risk factor, but consuming salad and bottled water are not. The association with salad may be explained by cross-contamination of food within the home, but the possibility that natural mineral water is a risk factor for campylobacter infection could have wide public health implications. PMID:14609455

Quality assessment of sachet and bottled water sold in Gboko ...

African Journals Online (AJOL)

The quality of selected sachet and bottled water produced and sold within Gboko town, Benue State was investigated to determine their Shelf life. Eight brands of sachet water and four brands of bottled water samples were collected from different manufacturers within 24 hours and stored at ambient temperature.

Assessing bottled water nitrate concentrations to evaluate total drinking water nitrate exposure and risk of birth defects.

Science.gov (United States)

Weyer, Peter J; Brender, Jean D; Romitti, Paul A; Kantamneni, Jiji R; Crawford, David; Sharkey, Joseph R; Shinde, Mayura; Horel, Scott A; Vuong, Ann M; Langlois, Peter H

2014-12-01

Previous epidemiologic studies of maternal exposure to drinking water nitrate did not account for bottled water consumption. The objective of this National Birth Defects Prevention Study (NBDPS) (USA) analysis was to assess the impact of bottled water use on the relation between maternal exposure to drinking water nitrate and selected birth defects in infants born during 1997-2005. Prenatal residences of 1,410 mothers reporting exclusive bottled water use were geocoded and mapped; 326 bottled water samples were collected and analyzed using Environmental Protection Agency Method 300.0. Median bottled water nitrate concentrations were assigned by community; mothers' overall intake of nitrate in mg/day from drinking water was calculated. Odds ratios for neural tube defects, limb deficiencies, oral cleft defects, and heart defects were estimated using mixed-effects models for logistic regression. Odds ratios (95% CIs) for the highest exposure group in offspring of mothers reporting exclusive use of bottled water were: neural tube defects [1.42 (0.51, 3.99)], limb deficiencies [1.86 (0.51, 6.80)], oral clefts [1.43 (0.61, 3.31)], and heart defects [2.13, (0.87, 5.17)]. Bottled water nitrate had no appreciable impact on risk for birth defects in the NBDPS.

Perceptions on the use of bottled water in restaurants in Harare's Central Business District (CBD)

Science.gov (United States)

Juba, Olivia Sakhile; Tanyanyiwa, Vincent Itai

2018-06-01

Bottled water use continues to expand worldwide and in the last two decades, a significant number of consumers have shifted from tap water to bottled water due to Cryptosporidium outbreaks. Bottled water consumption has increased in Harare due to erratic tap water supplies. Since 2011, forty bottled water brands have been banned because of failure to meet safety and quality standards due to contamination, unsuitable packaging, and wrong labelling. Nevertheless, the bottled water industry continues to thrive as local authorities fail to adequately purify municipal water. The study assessed the perceptions on drinking bottled water in restaurants within Harare's CBD. Demographic and social factors associated with bottled water users were established and the role and influence of stakeholders in bottling and distribution of water documented. A field survey through the administration of questionnaires to fifty restaurant users was carried out to assess the perceptions of people on the use of bottled water in terms of its safety and potential health benefits. Key informant interviews were conducted using a semi-structured interview with ten local water bottling companies as well as representatives from the Environmental Management Agency (EMA) and Standards Association of Zimbabwe (SAZ). Data were analysed using descriptive statistics and logistic regression analysis. Standard descriptive statistics were generated, with 95% confidence intervals (95% CIs). Consumers used bottled water as their primary drinking water source when they perceived that tap water was not safe. Perceptions of purity of water, bottled water convenience, and tap water unavailability seemed to determine consumption patterns among users. Females in the 18-48 age groups were more likely to think that bottled water was cleaner, safer, tasted better and was more convenient than tap water. Consumers regularly purchased bottled water for drinking and used bottled water as their primary drinking water

Effects of Water Bottle Materials and Filtration on Bisphenol A Content in Laboratory Animal Drinking Water.

Science.gov (United States)

Honeycutt, Jennifer A; Nguyen, Jenny Q T; Kentner, Amanda C; Brenhouse, Heather C

2017-05-01

Bisphenol A (BPA) is widely used in the polycarbonate plastics and epoxy resins that are found in laboratory animal husbandry materials including cages and water bottles. Concerns about BPA exposure in humans has led to investigations that suggest physiologic health risks including disruptions to the endocrine system and CNS. However, the extent of exposure of laboratory animals to BPA in drinking water is unclear. In the first study, we compared the amount of BPA contamination in water stored in plastic bottles used in research settings with that in glass bottles. The amount of BPA that leached into water was measured across several time points ranging from 24 to 96 h by using a BPA ELISA assay. The results showed that considerable amounts of BPA (approximately 0.15 μg/L) leached from polycarbonate bottles within the first 24 h of storage. In the second study, BPA levels were measured directly from water taken from filtered compared with unfiltered taps. We observed significantly higher BPA levels in water from unfiltered taps (approximately 0.40 μg/L) compared with taps with filtration systems (approximately 0.04 μg/L). Taken together, our findings indicate that the use of different types of water bottles and water sources, combined with the use of different laboratory products (food, caging systems) between laboratories, likely contribute to decreased rigor and reproducibility in research. We suggest that researchers consider reporting the types of water bottles used and that animal care facilities educate staff regarding the importance of flushing nonfiltered water taps when filling animal water bottles.

Organochlorine pesticides residues in bottled drinking water from Mexico City.

Science.gov (United States)

Díaz, Gilberto; Ortiz, Rutilio; Schettino, Beatriz; Vega, Salvador; Gutiérrez, Rey

2009-06-01

This work describes concentrations of organochlorine pesticides in bottled drinking water (BDW) in Mexico City. The results of 36 samples (1.5 and 19 L presentations, 18 samples, respectively) showed the presence of seven pesticides (HCH isomers, heptachlor, aldrin, and p,p'-DDE) in bottled water compared with the drinking water standards set by NOM-127-SSA1-1994, EPA, and World Health Organization. The concentrations of the majority of organochlorine pesticides were within drinking water standards (0.01 ng/mL) except for beta-HCH of BW 3, 5, and 6 samples with values of 0.121, 0.136, and 0.192 ng/mL, respectively. It is important monitoring drinking bottled water for protecting human health.

Hydrogeochemical and stable isotopic investigations on CO2-rich mineral waters from Harghita Mts. (Eastern Carpathians, Romania)

Science.gov (United States)

Kis, Boglárka-Mercedesz; Baciu, Călin; Kármán, Krisztina; Kékedy-Nagy, Ladislau; Francesco, Italiano

2013-04-01

There is a worldwide interest on geothermal, mineral and groundwater as a resource for energy, drinking water supply and therapeutic needs. The increasing trend in replacing tap water with commercial bottled mineral water for drinking purposes has become an economic, hydrogeologic and medical concern in the last decades. Several investigations have been carried out worldwide on different topics related to geothermal and mineral waters, dealing with mineral water quality assessment, origin of geothermal and mineral waters, geochemical processes that influence water chemistry and water-rock interaction In Romania, the Călimani-Gurghiu-Harghita Neogene to Quaternary volcanic chain (Eastern Carpathians) is one of the most important areas from the point of view of CO2-rich mineral waters. These mineral water springs occur within other post-volcanic phenomena like dry CO2 emissions, moffettes, bubbling pools, H2S gas emissions etc. Mineral waters from this area are used for bottling, local spas and drinking purposes for local people. The number of springs, around 2000 according to literature data, shows that there is still a significant unexploited potential for good quality drinking water in this area. Within the youngest segment of the volcanic chain, the Harghita Mts., its volcaniclastic aprons and its boundary with the Transylvanian Basin, we have carried out an investigation on 23 CO2-rich mineral water springs from a hydrogeochemical and stable isotopic point of view. The mineral waters are Ca-Mg-HCO3 to Na-Cl type. Sometimes mixing between the two types can be observed. We have detected a great influence of water-rock interaction on the stable isotopic composition of the mineral waters, shown by isotopic shifts to the heavier oxygen isotope, mixing processes between shallow and deeper aquifers and local thermal anomalies. Acknowledgements: The present work was financially supported by the Romanian National Research Council, Project PN-II-ID-PCE-2011-3-0537 and by

Community Responses to the Removal of Bottled Water on a University Campus

Science.gov (United States)

Mikhailovich, Katja; Fitzgerald, Robert

2014-01-01

Purpose: This paper aimed to examine the impact of the removal of bottled water on the campus community. This paper presents the findings of a survey conducted at the first Australian university to remove single-use bottled water from sale on a small regional university campus. The removal of bottled water from sale at the university formed part…

Content of 226Ra in tap and mineral waters of the Republic of Croatia and possible health effects

International Nuclear Information System (INIS)

Marovic, G.; Sencar, J.

1996-01-01

The paper describes the study of the content of 222 Ra in drinking water of Croatia: tap water from the public supply system of several major urban centres and bottled mineral water from two mineral water springs. 222 Ra was determined by alpha-spectrometric measurement after radiochemical separation. The study showed that 222 Ra concentrations for investigated categories of waters are below the levels at which any unacceptable dose due to ingestion would arise. (author)

Labeling practices of water bottling firms and its public health ...

African Journals Online (AJOL)

Background: Bottled water labels enable the consumers to choose brands that can best fit to their needs and preferences. Anything inaccurate, however, may pose serious public health risks, especially to vulnerable individuals. In Ethiopia, regular monitoring of bottled water quality and labelling practices is still lacking.

An alternative procedure for uranium analysis in drinking water using AQUALIX columns: application to varied French bottled waters.

Science.gov (United States)

Bouvier-Capely, C; Bonthonneau, J P; Dadache, E; Rebière, F

2014-01-01

The general population is chronically exposed to uranium ((234)U, (235)U, and (238)U) and polonium ((210)Po) mainly through day-to-day food and beverage intake. The measurement of these naturally-occurring radionuclides in drinking water is important to assess their health impact. In this work the applicability of calix[6]arene-derivatives columns for uranium analysis in drinking water was investigated. A simple and effective method was proposed on a specific column called AQUALIX, for the separation and preconcentration of U from drinking water. This procedure is suitable for routine analysis and the analysis time is considerably shortened (around 4h) by combining the separation on AQUALIX with fast ICP-MS measurement. This new method was tested on different French bottled waters (still mineral water, sparkling mineral water, and spring water). Then, the case of simultaneous presence of uranium and polonium in water was considered due to interferences in alpha spectrometry measurement. A protocol was proposed using a first usual step of spontaneous deposition of polonium on silver disc in order to separate Po, followed by the uranium extraction on AQUALIX column before alpha spectrometry counting. © 2013 Published by Elsevier B.V.

Applicability study of deuterium excess in bottled water life cycle analyses

Directory of Open Access Journals (Sweden)

Mihael Brenčič

2014-12-01

Full Text Available Paper explores the possible use of d‑excess in the investigation of bottled water. Based on the data set from Brencic and Vreca’s paper (2006. Identification of sources and production processes of bottled waters by stable hydrogen and oxygen isotope ratios, d‑excess values were statistically analysed and compared among different bottled water groups and different bottlers. The bottled water life cycle in relation to d‑excess values was also theoretically identified. Descriptive statistics and one-way ANOVA showed no significant differences among the groups. Differences were detected in the shape of empirical distributions. Groups of still and flavoured waters have similar shapes, but sparkling waters differed to the others. Two distinctive groups of bottlers could be discerned. The first group is represented by bottlers with a high range of d‑excess (from 7.7 ‰ to 18.6 ‰ with average of 12.0 ‰ exploring waters originating from the aquifers rich in highly mineralised groundwater and relatively high concentrations of CO2 gas. The second group is represented by bottlers using groundwater from relatively shallow aquifers. Their d‑excess values have characteristics similar to the local precipitation (from 7.8 ‰ to 14.3 ‰ with average of 10.3 ‰. More frequent sampling and better knowledge of production phases are needed to improve usage of isotope fingerprint for authentication of bottled waters.

Insulated Containers For Bottled Water (ICB)- Performance Evaluation

Science.gov (United States)

2017-04-21

WATER STOWAGE PROTOTYPES BOTTLED WATER HIGH TEMPERATURE WEIGHT EJECTION CONTAINERS ...Soldiers are ineffectively mounting commercially  available  coolers and they,  as well as the bottles they  contain , are becoming projectile hazards... container  (shown in Figure 15). The tie‐down procedures were determined by a professional  rigger; a video of the procedures is  available  from NSRDEC

The switch to refillable bottled water in Indonesia: a serious health risk

NARCIS (Netherlands)

Komarulzaman, A.; Jong, E. de; Smits, J.P.J.M.

2017-01-01

In recent years, the consumption of refillable bottled water has increased considerably in emerging countries. However, the quality of this water is often questionable, as authorities lack the capacity to properly check refilling depots. Given that refillable bottled water not only replaces

Temporal variation of microbiological and chemical quality of noncarbonated bottled drinking water sold in Sri Lanka.

Science.gov (United States)

Herath, A T; Abayasekara, C L; Chandrajith, Rohana; Adikaram, N K B

2012-03-01

Use of bottled water in Sri Lanka has increased over the last decade, while new brands of bottled water are often introduced to the market. However, the manufacturers' adherence to bottled water regulations is questionable, raising concerns regarding the quality of bottled water. The objective of the current study was to investigate the microbiological and chemical quality of bottled water in Sri Lanka. Thirty bottled water brands were sampled and their chemical and microbiological parameters were analyzed. Microbiological analysis was carried out within 1 to 3, 3 to 6, 6 to 9, and 9 to 12 mo after the date of manufacture. The results indicated that 63% of brands tested exceeded the levels permitted by the Sri Lanka Standards Institution (SLSI) for presumptive total coliforms (TC) (ammonia. The results of this study show the need for the bottling industry to be monitored closely by relevant authorities, in order to provide safe bottled drinking water to consumers in Sri Lanka. © 2012 Institute of Food Technologists®

Filling or Draining a Water Bottle with Two Holes

Science.gov (United States)

Cross, Rod

2016-01-01

Three simple experiments are described using a small water bottle with two holes in the side of the bottle. The main challenge is to predict and then explain the observations, but the arrangements can also be used for quantitative measurements concerning hydrostatic pressure, Bernoulli's equation, surface tension and bubble formation.

Safety of Bottled Water Beverages Including Flavored Water and Nutrient-Added Water Beverages

Science.gov (United States)

... Food Resources for You Consumers FDA Regulates the Safety of Bottled Water Beverages Including Flavored Water and Nutrient-Added Water Beverages ... addition, the flavorings and nutrients added to these beverages must comply with all applicable FDA safety requirements and they must be identified in the ...

Life cycle assessment of bottled water: A case study of Green2O products.

Science.gov (United States)

Horowitz, Naomi; Frago, Jessica; Mu, Dongyan

2018-03-01

This study conducted a full life cycle analysis of bottled water on four types of bottles: ENSO, PLA (corn based), recycled PET, and regular (petroleum based) PET, to discern which bottle material is more beneficial to use in terms of environmental impacts. PET bottles are the conventional bottles used that are not biodegradable and accumulate in landfills. PLA corn based bottles are derived from an organic substance and are degradable under certain environmental conditions. Recycled PET bottles are purified PET bottles that were disposed of and are used in a closed loop system. An ENSO bottle contains a special additive which is designed to help the plastic bottle degrade after disposed of in a landfill. The results showed that of all fourteen impact categories examined, the recycled PET and ENSO bottles were generally better than the PLA and regular PET bottles; however, the ENSO had the highest impacts in the categories of global warming and respiratory organics, and the recycled PET had the highest impact in the eutrophication category. The life cycle stages that were found to have the highest environmental impacts were the bottle manufacturing stage and the bottled water distribution to storage stage. Analysis of the mixed bottle material based on recycled PET resin and regular PET resin was discussed as well, in which key impact categories were identified. The PLA bottle contained extremely low impacts in the carcinogens, respiratory organics and global warming categories, yet it still contained the highest impacts in seven of the fourteen categories. Overall, the results demonstrate that the usage of more sustainable bottles, such as biodegradable ENSO bottles and recycled PET bottles, appears to be a viable option for decreasing impacts of the bottled water industry on the environment. Published by Elsevier Ltd.

Antimony leaching from polyethylene terephthalate (PET) plastic used for bottled drinking water.

Science.gov (United States)

Westerhoff, Paul; Prapaipong, Panjai; Shock, Everett; Hillaireau, Alice

2008-02-01

Antimony is a regulated contaminant that poses both acute and chronic health effects in drinking water. Previous reports suggest that polyethylene terephthalate (PET) plastics used for water bottles in Europe and Canada leach antimony, but no studies on bottled water in the United States have previously been conducted. Nine commercially available bottled waters in the southwestern US (Arizona) were purchased and tested for antimony concentrations as well as for potential antimony release by the plastics that compose the bottles. The southwestern US was chosen for the study because of its high consumption of bottled water and elevated temperatures, which could increase antimony leaching from PET plastics. Antimony concentrations in the bottled waters ranged from 0.095 to 0.521 ppb, well below the US Environmental Protection Agency (USEPA) maximum contaminant level (MCL) of 6 ppb. The average concentration was 0.195+/-0.116 ppb at the beginning of the study and 0.226+/-0.160 ppb 3 months later, with no statistical differences; samples were stored at 22 degrees C. However, storage at higher temperatures had a significant effect on the time-dependent release of antimony. The rate of antimony (Sb) release could be fit by a power function model (Sb(t)=Sb 0 x[Time, h]k; k=8.7 x 10(-6)x[Temperature ( degrees C)](2.55); Sb 0 is the initial antimony concentration). For exposure temperatures of 60, 65, 70, 75, 80, and 85 degrees C, the exposure durations necessary to exceed the 6 ppb MCL are 176, 38, 12, 4.7, 2.3, and 1.3 days, respectively. Summertime temperatures inside of cars, garages, and enclosed storage areas can exceed 65 degrees C in Arizona, and thus could promote antimony leaching from PET bottled waters. Microwave digestion revealed that the PET plastic used by one brand contained 213+/-35 mgSb/kg plastic; leaching of all the antimony from this plastic into 0.5L of water in a bottle could result in an antimony concentration of 376 ppb. Clearly, only a small

40 CFR 141.101 - Use of bottled water.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Use of bottled water. 141.101 Section 141.101 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Use of Non-Centralized Treatment Devices § 141.101...

[A norovirus-borne outbreak caused by contaminated bottled spring water in a school, Zhejiang province].

Science.gov (United States)

Shen, Ji-chuan; Lin, Jun-fen; Gao, Jie; Yao, Wen-ting; Wen, Dong; Liu, Guang-tao; Han, Jian-kang; Ma, Hui-lai; Zhang, Li-jie; Zhu, Bao-ping

2011-08-01

To study a local hospital reported acute gastroenteritis in a boarding school on its source of infection, mode of transmission and risk factors of the infection. A suspected case was defined as who had developed diarrhea (≥ 3 times/day) or vomiting among teachers or students of the school, during April 19 - 30, 2010. A confirmed case was from a probable case plus tested positive for norovirus in stool specimens by using RT-PCR. Stool specimens of cases and environmental specimens were collected for laboratory diagnosis. In a case-control study, we compared exposures to sources of bottled water, consumption of bottled water, and hygienic habits of 220 probable or confirmed cases from April 21 - 23 in the peak of the outbreak, together with another 220 controls, with frequency-matched by school grade. 20.3% of the 1536 students but none of the teachers developed the disease. 98.6% of the cases (n = 217) and 85.5% (n = 188) of the controls had drunk bottled water in the classroom (OR(M-H) = 12.3, 95%CI: 3.7 - 40.9). 47.9% (n = 104) of the cases and 41.5% (n = 78) of the controls had drunk unboiled bottled water in classroom (OR(M-H) = 3.8, 95%CI: 1.5 - 9.6). 47.9% (n = 104) of the cases and 48.4% (n = 91) of the controls had drunk bottled mixed water (boiled and unboiled) in the classroom (OR(M-H) = 2.8, 95%CI: 1.1 - 7.0). Stool specimens from 3 cases and one bottle of uncovered bottled water in classroom showed positive of having norovirus genotype II. Coliforms was cultured much higher rates than standard deviations in the bottled water. The factory making the bottled water was not licensed or having strict disinfection facilities. Bottled spring water contaminated by norovirus was responsible for this outbreak.

SmartStuff: A case study of a smart water bottle.

Science.gov (United States)

Jovanov, Emil; Nallathimmareddygari, Vindhya R; Pryor, Jonathan E

2016-08-01

The rapid growth of Internet of Things (IoT) and miniature wearable biosensors have generated new opportunities for personalized eHealth and mHealth services. Smart objects equipped with physiological sensors can provide robust monitoring of activities of daily living and context for wearable physiological sensors. We present a case study of an intelligent water bottle that can precisely measure the amount of liquid in the bottle, monitor activity using inertial sensors, and physiological parameters using a touch and photoplethysmographic sensor. We evaluate two system configurations: a smart water bottle integrated into a personal body sensor network and a cloud based device. This paper presents system organization and the results from preliminary field testing of the prototype device.

White HDPE bottles as source of serious contamination of water samples with Ba and Zn.

Science.gov (United States)

Reimann, Clemens; Grimstvedt, Andreas; Frengstad, Bjørn; Finne, Tor Erik

2007-03-15

During a recent study of surface water quality factory new white high-density polyethylene (HDPE) bottles were used for collecting the water samples. According to the established field protocol of the Geological Survey of Norway the bottles were twice carefully rinsed with water in the field prior to sampling. Several blank samples using milli-Q (ELGA) water (>18.2 MOmega) were also prepared. On checking the analytical results the blanks returned values of Ag, Ba, Sr, V, Zn and Zr. For Ba and Zn the values (c. 300 microg/l and 95 microg/l) were about 10 times above the concentrations that can be expected in natural waters. A laboratory test of the bottles demonstrated that the bottles contaminate the samples with significant amounts of Ba and Zn and some Sr. Simple acid washing of the bottles prior to use did not solve the contamination problem for Ba and Zn. The results suggest that there may exist "clean" and "dirty" HDPE bottles depending on manufacturer/production process. When collecting water samples it is mandatory to check bottles regularly as a possible source of contamination.

The bacteriological quality of different brands of bottled water available to consumers in Ile-Ife, south-western Nigeria.

Science.gov (United States)

Igbeneghu, Oluwatoyin A; Lamikanra, Adebayo

2014-11-28

The upsurge in the demand for bottled water has prompted the interest of many manufacturers in the production of bottled water and very many water bottling companies are therefore involved in its production. These range from large scale multinational companies to medium scale business enterprises, institutional and government business investment companies as well as small scale entrepreneurs. There is however little information on the comparative quality of bottled water brands produced by different classes of water bottling companies in Nigeria. This study was undertaken to determine the bacteriological quality of brands of bottled water available to consumers in Ile-Ife. Forty-three samples of bottled water comprising of three batches each of thirteen bottled water brands and two batches of two brands were purchased and analyzed for total bacterial count, presence of coliform and the presence of other bacterial indicators of drinking water quality. Only 67.4% of the water samples representing the products of 10 companies or 66.7% of the brands had heterotrophic counts within the acceptable limits. Coliforms present in 100 ml of water were detected in 26.7% of the bottled water brands. Other indicator organisms detected included Staphylococci isolated from 27.9% of the samples (33.3% of the brands) and specifically Staphylococcus aureus found in four brands constituting 14% of the samples. Pseudomonas strains were consistently detected in consecutive batches of three brands of the water samples. Bottled water samples produced by the large scale multinational producers were of acceptable bacteriological quality unlike those produced by most small companies. There is need for a greater control of water bottling processes carried out by commercial bottled water producers in Nigeria.

Predictors of Drinking Water Boiling and Bottled Water Consumption in Rural China: A Hierarchical Modeling Approach.

Science.gov (United States)

Cohen, Alasdair; Zhang, Qi; Luo, Qing; Tao, Yong; Colford, John M; Ray, Isha

2017-06-20

Approximately two billion people drink unsafe water. Boiling is the most commonly used household water treatment (HWT) method globally and in China. HWT can make water safer, but sustained adoption is rare and bottled water consumption is growing. To successfully promote HWT, an understanding of associated socioeconomic factors is critical. We collected survey data and water samples from 450 rural households in Guangxi Province, China. Covariates were grouped into blocks to hierarchically construct modified Poisson models and estimate risk ratios (RR) associated with boiling methods, bottled water, and untreated water. Female-headed households were most likely to boil (RR = 1.36, p water, or use electric kettles if they boiled. Our findings show that boiling is not an undifferentiated practice, but one with different methods of varying effectiveness, environmental impact, and adoption across socioeconomic strata. Our results can inform programs to promote safer and more efficient boiling using electric kettles, and suggest that if rural China's economy continues to grow then bottled water use will increase.

Is Your Drinking Water Acidic? A Comparison of the Varied pH of Popular Bottled Waters.

Science.gov (United States)

Wright, Kellie F

2015-06-01

Dental professionals continually educate patients on the dangers of consuming acidic foods and beverages due to their potential to contribute to dental erosion and tooth decay. Excess acid in the diet can also lead to acidosis, which causes negative systemic side effects. However, water is not typically categorized as acidic. The purpose of this in-vitro study was to investigate the pH levels of several popular brands of bottled water and compare them to various other acidic beverages. Two different brands of marketed alkaline water (with a pH of 8.8 or higher) were also studied, tested for acidity and described. A pilot in-vitro study was conducted to determine the pH levels of a convenience sample of popular brands of bottled water, tap water and other known acidic beverages in comparison with the pH values reported on the respective manufacturers' website. Each beverage was tested in a laboratory using a calibrated Corning pH meter model 240, and waters were compared to the corresponding company's testified pH value. Waters were also compared and contrasted based on their process of purification. The data was then compiled and analyzed descriptively. The pH values for the tested beverages and bottled waters were found to be predominantly acidic. Ten out of the 14 beverages tested were acidic (pHwaters were neutral (pH=7) and 2 bottled waters were alkaline (pH>7). The majority of waters tested had a more acidic pH when tested in the lab than the value listed in their water quality reports. It is beneficial for the health care provider to be aware of the potential acidity of popular bottled drinking waters and educate patients accordingly. Copyright © 2015 The American Dental Hygienists’ Association.

Ultra-trace analysis of hormones, pharmaceutical substances, alkylphenols and phthalates in two French natural mineral waters

Energy Technology Data Exchange (ETDEWEB)

Dévier, Marie-Hélène; Le Menach, Karyn [Environnements et Paléoenvironnements Océaniques et Continentaux (EPOC, UMR 5805 CNRS), Laboratoire de Physico- et Toxico-Chimie de l' Environnement (LPTC), Université de Bordeaux, 351 cours de la Libération, 33405 Talence cedex (France); Viglino, Liza [Danone Waters Analytical Center, Aqualab, Place de la Gare, 74500 Evian-Les-Bains (France); Di Gioia, Lodovico [Danone Research, R and D Waters Division, RD 128, 91767 Palaiseau Cedex (France); Lachassagne, Patrick [Danone Waters France, Environment and Water Resources Division, BP 87, 11 av. Général Dupas, 74500 Evian-Les-Bains cedex (France); Budzinski, Hélène, E-mail: h.budzinski@epoc.u-bordeaux1.fr [Environnements et Paléoenvironnements Océaniques et Continentaux (EPOC, UMR 5805 CNRS), Laboratoire de Physico- et Toxico-Chimie de l' Environnement (LPTC), Université de Bordeaux, 351 cours de la Libération, 33405 Talence cedex (France)

2013-01-15

The aim of this work was to investigate the potential presence of a broad range of organic compounds, such as hormones, alkylphenols, bisphenol A and phthalates, as well as pharmaceutical substances in two brands of bottled natural mineral waters (Evian and Volvic, Danone). The phthalates were determined by solid-phase microextraction coupled to gas chromatography–mass spectrometry (SPME-GC–MS) and the other compounds by liquid chromatography–tandem mass spectrometry (LC–MS/MS) or gas chromatography–mass spectrometry (GC–MS) after solid-phase extraction. The potential migration of alkylphenols, bisphenol A and phthalates from polyethylene terephthalate (PET) bottles was also investigated under standardized test conditions. Evian and Volvic natural mineral waters contain none of the around 120 targeted organic compounds. Traces of 3 pharmaceuticals (ketoprofen, salicylic acid, and caffeine), 3 alkylphenols (4-nonylphenol, 4-t-octylphenol, and 4-nonylphenol diethoxylate), and some phthalates including di(2-ethylhexyl)phthalate (DEHP) were detected in the samples, but they were also present in the procedural blanks at similar levels. The additional test procedures demonstrated that the few detected compounds originated from the background laboratory contamination. Analytical procedures have been designed both in the bottling factory and in the laboratory in order to investigate the sources of DEHP and to minimize to the maximum this unavoidable laboratory contamination. It was evidenced that no migration of the targeted compounds from bottles occurred under the test conditions. The results obtained in this study underline the complexity of reaching a reliable measure to qualify the contamination of a sample at ultra-trace level, in the field of very pure matrices. The analytical procedures involving glassware, equipment, hoods, and rooms specifically dedicated to trace analysis allowed us to reach reliable procedural limits of quantification at the ng

Ultra-trace analysis of hormones, pharmaceutical substances, alkylphenols and phthalates in two French natural mineral waters

International Nuclear Information System (INIS)

Dévier, Marie-Hélène; Le Menach, Karyn; Viglino, Liza; Di Gioia, Lodovico; Lachassagne, Patrick; Budzinski, Hélène

2013-01-01

The aim of this work was to investigate the potential presence of a broad range of organic compounds, such as hormones, alkylphenols, bisphenol A and phthalates, as well as pharmaceutical substances in two brands of bottled natural mineral waters (Evian and Volvic, Danone). The phthalates were determined by solid-phase microextraction coupled to gas chromatography–mass spectrometry (SPME-GC–MS) and the other compounds by liquid chromatography–tandem mass spectrometry (LC–MS/MS) or gas chromatography–mass spectrometry (GC–MS) after solid-phase extraction. The potential migration of alkylphenols, bisphenol A and phthalates from polyethylene terephthalate (PET) bottles was also investigated under standardized test conditions. Evian and Volvic natural mineral waters contain none of the around 120 targeted organic compounds. Traces of 3 pharmaceuticals (ketoprofen, salicylic acid, and caffeine), 3 alkylphenols (4-nonylphenol, 4-t-octylphenol, and 4-nonylphenol diethoxylate), and some phthalates including di(2-ethylhexyl)phthalate (DEHP) were detected in the samples, but they were also present in the procedural blanks at similar levels. The additional test procedures demonstrated that the few detected compounds originated from the background laboratory contamination. Analytical procedures have been designed both in the bottling factory and in the laboratory in order to investigate the sources of DEHP and to minimize to the maximum this unavoidable laboratory contamination. It was evidenced that no migration of the targeted compounds from bottles occurred under the test conditions. The results obtained in this study underline the complexity of reaching a reliable measure to qualify the contamination of a sample at ultra-trace level, in the field of very pure matrices. The analytical procedures involving glassware, equipment, hoods, and rooms specifically dedicated to trace analysis allowed us to reach reliable procedural limits of quantification at the ng

Random survey of the microbial quality of bottled water in South Africa

African Journals Online (AJOL)

Total and faecal coliform bacteria, enterococci, C. perfringens, bacteriophages or enteric viruses were not detected in any of the ten bottled water samples analysed. It can be concluded that the microbial quality of eight of the ten selected bottled water samples analysed was within the acceptable limits set by the SABS ...

Stochastic Optimization in The Power Management of Bottled Water Production Planning

Science.gov (United States)

Antoro, Budi; Nababan, Esther; Mawengkang, Herman

2018-01-01

This paper review a model developed to minimize production costs on bottled water production planning through stochastic optimization. As we know, that planning a management means to achieve the goal that have been applied, since each management level in the organization need a planning activities. The built models is a two-stage stochastic models that aims to minimize the cost on production of bottled water by observing that during the production process, neither interfernce nor vice versa occurs. The models were develop to minimaze production cost, assuming the availability of packing raw materials used considered to meet for each kind of bottles. The minimum cost for each kind production of bottled water are expressed in the expectation of each production with a scenario probability. The probability of uncertainly is a representation of the number of productions and the timing of power supply interruption. This is to ensure that the number of interruption that occur does not exceed the limit of the contract agreement that has been made by the company with power suppliers.

Estrogenic activity, selected plasticizers and potential health risks associated with bottled water in South Africa.

Science.gov (United States)

Aneck-Hahn, Natalie H; Van Zijl, Magdalena C; Swart, Pieter; Truebody, Barry; Genthe, Bettina; Charmier, Jessica; Jager, Christiaan De

2018-04-01

Potential endocrine disrupting chemicals (EDCs) are present in bottled water from various countries. In South Africa (SA), increased bottled water consumption and concomitant increases in plastic packaging create important consequences for public health. This study aimed to screen SA bottled water for estrogenic activity, selected target chemicals and assessing potential health risks. Ten bottled water brands were exposed to 20 °C and 40 °C over 10 days. Estrogenic activity was assessed using the recombinant yeast estrogen screen (YES) and the T47D-KBluc reporter gene assay. Solid phase extracts of samples were analyzed for bis(2-ethylhexyl) adipate (DEHA), selected phthalates, bisphenol-A (BPA), 4-nonylphenol (4-NP), 17β-estradiol (E 2 ), estrone (E 1 ), and ethynylestradiol (EE 2 ) using gas chromatography-mass spectrophotometry. Using a scenario-based health risk assessment, human health risks associated with bottled water consumption were evaluated. Estrogenic activity was detected at 20 °C (n = 2) and at 40 °C (n = 8). Estradiol equivalent (EEq) values ranged from 0.001 to 0.003 ng/L. BPA concentrations ranged from 0.9 ng/L to 10.06 ng/L. Although EEqs and BPA concentrations were higher in bottled water stored at 40 °C compared to 20 °C, samples posed an acceptable risk for a lifetime of exposure. Irrespective of temperature, bottled water from SA contained chemicals with acceptable health risks.

Random survey of the microbial quality of bottled water in South Africa

African Journals Online (AJOL)

Random survey of the microbial quality of bottled water in South Africa. Marthie M Ehlers, Walda B Van Zyl, Dobromir N Pavlov, Etienne E Muller. Abstract. Due to the increased demand and consumption of bottled water in South Africa, there has been a growing concern about the microbiological quality of this product.

Preference for tap, bottled, and recycled water: Relations to PTC taste sensitivity and personality.

Science.gov (United States)

Harmon, Daniel; Gauvain, Mary; Z Reisz; Arthur, Isaac; Story, S Drew

2018-02-01

This study investigated people's preferences for different water sources and factors that predict such preferences using a blind taste test. Water preferences of 143 participants for one name-brand bottled water, one groundwater-sourced tap water, and one indirect potable reuse (IDR) water were assessed. For predictors of water preference, we measured each participant's PTC taste sensitivity and assessed two personality traits (Neuroticism, Openness to Experience). We also explored participants' descriptions of each water source. Results indicate a preference for water treated with Reverse Osmosis (RO) (bottled and IDR water) over groundwater-sourced water, which had higher pH levels and lower concentrations of Ca and HCO 3 - . PTC taste sensitivity did not predict preferences, while Openness to Experience and Neuroticism predicted preference for IDR water. Positive relations between Openness to Experience and preferences for bottled and IDR water were moderated by gender and were stronger among females. Participants described water primarily by its taste and texture. Findings suggest that (1) tap water treated by RO is equally preferable to some bottled water, (2) personality traits may affect water preferences, and (3) prior findings of gender differences in preferences for bottled water may reflect personality characteristics. Efforts to increase acceptance for sustainable water alternatives, such as IDR, may be more successful by assuring consumers about taste and addressing personality traits that encourage or inhibit use. Copyright © 2017 Elsevier Ltd. All rights reserved.

Natural radioactivity in mineral and spa water: the current regulatory approach in Italy

International Nuclear Information System (INIS)

Nuccetelli, C.; Bochicchio, F.; Ruocco, G.

2004-01-01

Mineral and thermal waters can contain radioactivity of natural origin which, in some cases, can lead to radiation-protection problems for both workers and consumers. In Italy, as in many other countries, the consumption of bottled mineral water is rather high and the practice of spending short stays in spas is also popular. Consumer protection against natural radioactivity in mineral water is not regulated at all and exposure from thermal waters is not treated in detail, in either the European Union or Italy. For this reason, the Italian Ministry of Health - which has the duty to authorize spa activities and the sale of mineral water on the basis of water characteristics - asked the Istituto Superiore di Sanita (the Italian National Institute of Health) to provide ad-hoc reports containing both dosimetric calculations and analysis of the radiation-protection regulations to be applied in these situations. On the basis of these reports, the Ministry of Health decided, in two statements for spa and mineral waters respectively, to indicate upper levels for natural radioactivity content. Since 2002, spa water parameters have been in force for authorization of their use and sale, and are to be promulgated by specific and more comprehensive regulations. For mineral waters used for infant feeding and drinking, levels lower than those for general public uses have been proposed, in order to take into account the higher ingestion dose coefficients for infants. At the moment, mineral water levels are not enforced as law. This paper presents the dosimetric calculation results and the Ministry of Health statements. (Author) 17 refs

Treatment techniques for the recycling of bottle washing water in the soft drinks industry.

Science.gov (United States)

Ramirez Camperos, E; Mijaylova Nacheva, P; Diaz Tapia, E

2004-01-01

The soft drink production is an important sector in the manufacturing industry of Mexico. Water is the main source in the production of soft drinks. Wastewater from bottle washing is almost 50% of the total wastewater generated by this industry. In order to reduce the consumption of water, the water of the last bottle rinse can be reused in to the bottle pre-rinse and pre-washing cycles. This work presents the characterization of the final bottle washing rinse discharge and the treatability study for the most appropriate treatment system for recycling. Average characteristics of the final bottle wash rinse were as follows: Turbidity 40.46 NTU, COD 47.7 mg/L, TSS 56 mg/L, TS 693.6 mg/L, electrical conductivity 1,194 microS/cm. The results of the treatability tests showed that the final rinse water can be used in the pre-rinse and pre-washing after removing the totality of the suspended solids, 80% of the COD and 75% of the dissolved solids. This can be done using the following treatment systems: filtration-adsorption-reverse osmosis, or filtration-adsorption-ion exchange. The installation of these treatment techniques in the soft drink industry would decrease bottle washing water consumption by 50%.

Preconcentration and Determination of Antimony in Drinking Water Bottled by Modified Nano-Alumina

Directory of Open Access Journals (Sweden)

M Mohammad Zakizade

2016-01-01

Full Text Available Abstract Introduction: Antimony trioxide (Sb2O3 has been utilized as a catalyst in polyethylene terephtalate (PET production, and the studies conducted on the bottled water has demonstrated that antimony can be leached from PET bottles into drinking water. Methods: In this study, a simple method was applied in order to determine the trace amount of antimony in bottled drinking water based on preconcentration /solid phase extraction. The nano alumina modified with Schiff base ligand was used in regard with Sb preconcentration. The experiments were performed in a continuous system and HCI was used as eluent of Sb ion. Several chemical and flow variables were optimized for a quantitative preconcentration and determination of Sb ion. The atomic absorption spectroscopy was used to determine Sb ion concentration. In order to study the keeping conditions on the leaching of Sb ion from PET plastic, drinking water bottles were kept in different conditions(room temperature, sunny light and -18˚C. Results: The calibration graph was linear in the range of 0.5 to 15.0 ppm Sb with detection limit of 0.055 ppm. The flow rate of sample was optimized in range of 1.0-9.0 mLmin-1 and Sb ion can be quantitatively eluted at 90 Vsample: Veluent retio. Conclusion: The study results revealed that the modified nano alumina is an effective sorbent in regard with absorbing Sb ion from water and HCI 1M can be used as an appropriate eluent. Maximum leaching of Sb ion is observed when the bottled drinking water was exposed to the sun light. Keywords: Antimony; Bottled drinking water; Modified alumina; Preconcentration

Community Response to Impaired Drinking Water Quality: Evidence from Bottled Water Sales

Science.gov (United States)

Allaire, M.; Zheng, S.; Lall, U.

2017-12-01

Drinking water contaminants pose a harm to public health. When confronted with elevated contaminate levels, individuals can take averting actions to reduce exposure, such as bottled water purchases. This study addresses a problem of national interest given that 9 to 45 million people have been affected by drinking water quality violations in each of the past 34 years. Moreover, few studies address averting behavior and avoidance costs due to water quality violations. This study assesses how responses might differ across baseline risk of impaired water quality and demographics of service area. We match a panel of weekly supermarket sales data with geocoded violations data for 67 counties in the Southeast from 2006-2015. We estimate the change in bottled water sales due to drinking water violations using a fixed effects model. Observing market behavior also allows us to calculate the cost of these averting actions. Critical findings from this study contribute to understanding how communities respond to water quality violations. We find that violations have considerable effects on bottled water consumption. Sales increase 8.1 percent due to violations related to microorganisms and 31.2 percent due to Tier 1 violations, which pose an immediate health risk. In addition, we calculate a national cost of averting actions of $26 million for microorganism violations from 2006-2015, which represents a lower-bound estimate. Averting costs vary considerably across the U.S. and some counties bear a particularly large burden, such as in California and Texas. Overall, this study provides insight into how averting behavior differs across contaminant type, water utility characteristics, and community demographics. Such knowledge can aid public health agencies, water systems, and environmental regulators to direct assistance to communities most in need.

Natural mineral bottled waters available on the Polish market as a source of minerals for the consumers. Part 2: The intake of sodium and potassium.

Science.gov (United States)

Gątarska, Anna; Ciborska, Joanna; Tońska, Elżbieta

Natural mineral waters are purchased and consumed according to consumer preferences and possible recommendations. The choice of appropriate water should take into account not only the general level of mineralization but also the content of individual components, including electrolytes such as sodium and potassium. Sodium is necessary to ensure the proper physiological functions of the body. It is defined as a health risk factor only when its excessive intake occurs. Potassium acts antagonistically towards sodium and calcium ions, contributes to a reduction of the volume of extracellular fluids and at the same time reduces muscle tension and permeability of cell membranes. The demand for sodium and potassium is of particular importance in people expending significant physical effort, where an increased electrolyte supply is recommended. The aim of the study was to estimate the content of sodium and potassium in natural mineral waters available in the Polish market and to evaluate the intake of those components with the commercially available mineral waters by different groups of consumers at the assumed volume of their consumption. The research material consisted of natural mineral waters of forty various brands available on the Polish market. The examined products were either produced in Poland or originated in other European countries. Among the products under examination, about 30% of the waters were imported from Lithuania, Latvia, the Czech Republic, France, Italy and Germany. A sample for analyses consisted of two package units of the examined water from different production lots. Samples for research were collected at random. The study was conducted with the same samples in in which calcium and magnesium content was determined, which was the subject of the first part of the study. The content of sodium and potassium was determined using the emission technique (acetylene-air flame), with the use of atomic absorption spectrometer – ICE 3000 SERIES – THERMO

[Mineral water as a cure].

Science.gov (United States)

Nocco, Priska Binz

2008-01-01

resorts mentioned, especially regarding the quality and quantity aspects of the performed mineral water analyses, as well as in the reported written evidence and publications on the success of the therapies. Differences were also to be found in the conditions of the health resort facilities and in the medical support given. The therapy opportunities included mainly drinking and bath cures, which could occur alone or in combination. In the mentioned health resorts different clinical disease symptoms were treated. The most important baths were located in Acquarossa and Stabio, which were specialized in selected therapeutical domains, because of their particular water compositions. Numerous personalities from science and politics were concerned by the local springs and accepted to contribute to the promotion of these structures. Their engagement led to the integration of the native springs in the Farmacopea Ticinese. Since at that time it was extremely difficult to find experienced mineral water analysts in the region, the analyses of local native sources were assigned to qualified experts mainly coming from Italy. This scientific co-operation between the southern part of Switzerland and the northern part of Italy was, already at that time, active also in other work domains. The evaluation of the historical documentation available from the Farmacia Vantussi shows that this pharmacy supplied a considerable assortment of national and foreign spring waters, as well as foreign dried components. Of commercial interest was, to be noted, the free sale of the waters to hospitals, institutions, hotels, restaurants as well as to private households. The sales of waters and of their dried components upon prescription, however, constituted only the minor part. The introduction of the industrial bottling occurring in the first decades of the 20th century, led to a lowering price trend, through which the product 'mineral water' became accessible to a broader public. Henceforth its

75 FR 14607 - Small Entity Compliance Guide: Bottled Water: Total Coliform and E. coli

Science.gov (United States)

2010-03-26

...] Small Entity Compliance Guide: Bottled Water: Total Coliform and E. coli; Availability AGENCY: Food and... the availability of a guidance for industry entitled ``Bottled Water: Total Coliform and E. coli... determine whether any of the coliform organisms are Escherichia coli (E. coli), an indicator of fecal...

THE ANALYSIS OF THE THREAT OF REUSING PET BOTTLES FOR THE STORAGE OF DRINKING WATER

Directory of Open Access Journals (Sweden)

Manuilov A. M.

2017-12-01

Full Text Available Introduction. According to a sociological survey of about 86% of Kharkiv (Ukraine residents reuse PET bottles for a drinking water storing. This type of reuse of PET bottles isn't safe and the results of numerous research unequivocally confirm this assertion. The largest hazard of plastic bottles reuse for drinking water storage is biological film on the internally surface of bottle. This biofilm may contain pathogenic microorganisms which can migrate from biofilm to fresh water. Human, who drinking contaminated water, may drink microorganisms in common with this water. It's very dangerous, because the numerous strains of pathogens may migration in water and infect from gastric-bowel tract to the humans. Scientists from National technical university "Kharkiv polytechnic institute" in common with experts from Mechnikov institute of microbiology and immunology explored this problem and devised the apparatus, which can destroy a biofilm on polymer or another surface. Materials & Methods. The tested apparatus was the electrical device consisting of a block with electrodes, an electronic control, a water pump and a sprinkler for spraying the disinfectant. The electrode was made of 925˚ silver (sterling silver. Water for the preparation of a disinfectant was tap water and wasn't treated additionally. The sprinkler for spraying the disinfectant was placed in the neck of the infected bottle. Disinfectant solution was sprayed inside the bottle for 4 seconds. The water pressure was about 1.5 atmospheres. After that, the sprinkler was removed and the disinfectant was drained. A smear for microbiological composition was taken from three parts of the bottle - the neck, the middle part and the bottom. Growth of microorganisms and their detections was fixed by classic microbiological methods. Results & Discussion. In the article the scheme of the most probable and widespread way of infection of PET-bottles by pathogens and the way of minimization of this

Optimization of fixed titanium dioxide film on PET bottles and visual indicator for water disinfection

Science.gov (United States)

Heredia-Munoz, Manuel Antonio

Water is perhaps the most important resource that sustains human life. According to the World Health Organization (WHO), almost two billion people do not have access to the required water that is needed to satisfy their daily needs and one billion do not have access to clean sources of water for consumption, most of them living in isolated and poor areas around the globe. Poor quality water increases the risk of cholera, typhoid fever and dysentery, and other water-borne illness making this problem a real crisis that humankind is facing. Several water disinfection technologies have been proposed as solutions for this problem. Solar water disinfection using TiO2 coated PET bottles was the alternative that is studied in this work. This technology does not only inactivate bacteria but also disintegrates organic chemicals that can be present in water. The objectives of this work address the optimization of the TiO 2 coated PET bottles technologies. The improvement on the bottle coating process, using two coats of 10% W/V of TiO2 in a solution of vinegar and sodium bicarbonate to form the TiO2 film, the use of a different indigo carmine (1.25 X 10-1mg/pill) concentration in the pill indicator of contamination, the increase of the disinfection rate through shaking the bottles, degradation under intermittent UV radiation and the effect of bottle size on photocatalytic water disinfection were among the most important findings. A new mathematical model that describes better photocatalytic water disinfection in TiO2 coated bottles and simulates water disinfection under different working conditions was another important achievement. These results can now be used to design a strategy for disseminating this technology in areas where it is required and, in that way, generate the greatest positive impact on the people needing safe drinking water.

Concentration of Selected Anions in Bottled Water in the United Arab Emirates

Directory of Open Access Journals (Sweden)

Mohamed Yehia Z. Abouleish

2012-05-01

Full Text Available Several studies have shown concern over nitrate and nitrite contamination of prepared infant formula used by infants less than six months old, as it may lead to methemoglobinemia and death. One possible source of contamination is through the use of improperly treated drinking water. Contamination of water could result from fertilizers and manure runoff, not fully treated and released human and industrial waste, or from disinfection processes. In the United Arab Emirates (UAE, bottled water is the major source of drinking water and may be used for the preparation of infant formula. Therefore, in this study, several bottled water brands that are sold on the UAE market, and could be used for preparation of infant formula, were tested for nitrate and nitrite and other anions to show their compatibility with the permissible levels of the United States Environmental Protection Agency (U.S. EPA, United States Food and Drug Administration/Code of Federal Regulations (U.S. FDA/CFR, and other international organizations. All the bottled water samples demonstrated nitrate, nitrite, and other anions levels below the permissible levels accepted by U.S. EPA, U.S. FDA/CFR, and other international organizations, except for one sample that showed nitrite levels exceeding the European Commission and Drinking Water Directive (EC/DWD permissible levels. Such study sheds light on the quality of bottled water sold not only in the UAE and the region, but also in other countries, such as France, since some of them are imported. In addition, the results shed light on the effectiveness of the treatment processes and possible sources of infant formula contamination that can affect the health of infants.

Migration of bisphenol A into water from polycarbonate baby bottles during microwave heating

NARCIS (Netherlands)

Ehlert, K.A.; Beumer, C.W.E.; Groot, M.C.E.

2008-01-01

A comprehensive migration database was established for bisphenol A from polycarbonate baby bottles into water during exposure to microwave heating. Eighteen different brands of polycarbonate baby bottles sold in Europe were collected. Initial residual content of bisphenol A and migration after

Influence of bottled water packaging attributes on consumers ...

African Journals Online (AJOL)

The purpose of this study was to identify the influence of bottled water packaging attributes on consumers' purchase decision. The research focused in Addis Ababa (Ethiopia). The study used color, graphic design, size, printed information and shape of packaging as independent variables and consumers' purchase ...

Concentration of Nitrate in Bottled Drinking Water in Qom, Iran

Directory of Open Access Journals (Sweden)

Mohammad Saberi Bidgoli

2013-11-01

Full Text Available Background & Aims of the Study: The global consumption of bottled water is growing with substantial growth in sales volumes on every continent. The highest growth rates are occurring in Asia and South America. Biological and chemical monitoring of these waters is necessary. The aim of current study was determination of nitrate concentration in bottled drinking water in Qom, Iran in 2012. Materials & Methods: A cross-sectional study carried out in Qom, Iran. First of all, 18 most frequent brands of bottled drinking waters were purchased in June 2012 randomly. Then concentration of nitrate was measured according to the spectrophotometric method. In next step, experiment data were analyzed by Excel Software and P value was obtained by statistical calculations. Finally data were comprised with written nitrate concentration on labels and recommended permissible values . Results: The median nitrate concentration was 2.1 mg/L with the minimum 0.8 mg/L and maximum 8.1 mg/L. In 66.7 % of the samples, the measured nitrate concentrations were less than the written nitrate concentrations and in 33.3% of samples, the nitrate concentration was higher. The statistical calculation proved the significant difference between the median of written nitrate concentration on the label and investigated nitrate concentration (P value > 0.05. Conclusions: It be concluded that the measured nitrate concentration in all of the water samples is below the recommended permissible level.

The impact of geology on the migration of fluorides in mineral waters of the Bukulja and Brajkovac pluton area, Serbia

Directory of Open Access Journals (Sweden)

Papić Petar

2012-01-01

Full Text Available One of the hydrogeochemical parameters that classify groundwater as mineral water is the content of fluoride ions. Their concentration is both important and limited for bottled mineral waters. Hydrochemical research of mineral waters in the surrounding area of Bukulja and Brajkovac pluton, in central Serbia, was conducted in order to define the chemical composition and genesis of these waters. They are carbonated waters, with content of fluoride ranging from 0.2 up to 6.6 mg/L. Since hydrochemical analyses showed variations in the major water chemistry, it was obvious that, apart from hydrochemical research, some explorations of the structure of the regional terrain would be inevitable. For these purposes, some additional geological research was performed, creating an adequate basis for the interpretation of the genesis of these carbonated mineral waters. The results confirmed the significance of the application of hydrochemical methods in the research of mineral waters. The work tended to emphasize that “technological treatment” for decreasing the concentration of fluoride in mineral waters occurs in nature, indicating the existence of natural defluoridization. [Projekat Ministarstva nauke Republike Srbije, br. 43004

Screening of hormone-like activities in bottled waters available in Southern Spain using receptor-specific bioassays.

Science.gov (United States)

Real, Macarena; Molina-Molina, José-Manuel; Jiménez-Díaz, Inmaculada; Arrebola, Juan Pedro; Sáenz, José-María; Fernández, Mariana F; Olea, Nicolás

2015-01-01

Bottled water consumption is a putative source of human exposure to endocrine-disrupting chemicals (EDCs). Research has been conducted on the presence of chemicals with estrogen-like activity in bottled waters and on their estrogenicity, but few data are available on the presence of hormonal activities associated with other nuclear receptors (NRs). The aim of this study was to determine the presence of endocrine activities dependent on the activation of human estrogen receptor alpha (hERa) and/or androgen receptor (hAR) in water in glass or plastic bottles sold to consumers in Southern Spain. Hormone-like activities were evaluated in 29 bottled waters using receptor-specific bioassays based on reporter gene expression in PALM cells [(anti-)androgenicity] and cell proliferation assessment in MCF-7 cells [(anti-)estrogenicity] after optimized solid phase extraction (SPE). All of the water samples analyzed showed hormonal activity. This was estrogenic in 79.3% and anti-estrogenic in 37.9% of samples and was androgenic in 27.5% and anti-androgenic in 41.3%, with mean concentrations per liter of 0.113pM 17β-estradiol (E2) equivalent units (E2Eq), 11.01pM anti-estrogen (ICI 182780) equivalent units (ICI 182780Eq), 0.33pM methyltrienolone (R1881) equivalent units (R1881Eq), and 0.18nM procymidone equivalent units (ProcEq). Bottled water consumption contributes to EDC exposure. Hormone-like activities observed in waters from both plastic and glass bottles suggest that plastic packaging is not the sole source of contamination and that the source of the water and bottling process may play a role, among other factors. Further research is warranted on the cumulative effects of long-term exposure to low doses of EDCs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preparation of an Evaluated HACCP- Plan in Order to Implementation in Iranian Mineral Water Factories for Avoiding the Common Food Safety Hazards in Such Industries

Directory of Open Access Journals (Sweden)

Amin Kiyani

2014-12-01

Full Text Available Background: consumption of mineral waters in the world has increased in recent years, and also concerns of consumers about its contamination are growing. Thereby, implementation of such a protective system as HACCP can prevent contamination of waters by different agents. This research aimed to develop an HACCP-Plan standard for mineral waters manufacturing factories in Iran. Methods: In current study, like production lines, polyethylene terephthalate (PET containers packaging, warehouses and laboratories sections of factories were observed from view of production and quality control. To monitor, control and restrict the hazards, seven principles of HACCP were considered. In continue applicable solutions were presented inclusive and practically for all factories. Required information were verified and presented through investigation of national and international standards. Results: The results shown that lack of sanitizing mineral water supplies and factories environment, incomplete water treatment, non-standard production of PET bottles, improper storage of raw materials and final product, and lack of inspection of equipment led to the increasing health hazards of the product and endanger the consumers health. Conclusion: In order to produce safe mineral water, it is necessary to sanitize the water supplies and factory environment. In addition, the process of water treatment and the production of PET bottles must be according to national and international standards. As the implementation of the HACCP system in various mineral water producing factories is not same, application of developed system in this research will be effective to standardize the implementation of this system in plants.

PROFILE OF PLASTIC WATER BOTTLES WASTES PROCESSING BUSINESS UNIT FOR WASTE PICKERS

Directory of Open Access Journals (Sweden)

Herijanto P.

2017-09-01

Full Text Available Used plastic water bottles waste pickers can be categorized as one of the informal sector’s component. They work for themselves by picking up used water bottles and selling them to the waste collectors. The problem to be solved in this research is How the Most Appropriate Used Plastic Water Bottles Business Model for Waste Pickers Is that enables them to be categorized as formal sector. From the result of the interview with 120 waste pickers, 96 results were qualified to be analyzed. The interview was located in several waste collectors, which were visited by waste pickers at certain hours. The data were analyzed descriptively based on six business aspects. Specifically for production facilities, Quality Function Deployment (QFD and Value Engineering (VE analysis were performed. The results of the analysis indicate that the business is practicable for waste pickers and has the potential to enable them run a formal business sector.

Presence of polychlorinated biphenyls (PCBs) in bottled drinking water in Mexico City.

Science.gov (United States)

Salinas, Rutilio Ortiz; Bermudez, Beatriz Schettino; Tolentino, Rey Gutiérrez; Gonzalez, Gilberto Díaz; Vega y León, Salvador

2010-10-01

This paper describes the concentrations of seven polychlorinated biphenyls (PCBs) in bottled drinking water samples that were collected over 1 year from Mexico City in two sizes (1.5 and 19 L), using gas chromatography with an electron capture detector. PCBs 28 (0.018-0.042 μg/L), 52 (0.006-0.015 μg/L) and 101 (0.001-0.039 μg/L) were the most commonly found and were present in the majority of the samples. However, total concentrations of PCBs in bottled drinking water (0.035-0.039 μg/L) were below the maximum permissible level of 0.50 μg/L stated in Mexican regulations and probably do not represent a hazard to human health. PCBs were detectable in all samples and we recommend a monitoring program be established to better understand the quality of drinking bottled water over time; this may help in producing solutions for reducing the presence of organic contaminants.

77 FR 25721 - Small Entity Compliance Guide: Bottled Water: Quality Standard: Establishing an Allowable Level...

Science.gov (United States)

2012-05-01

...] Small Entity Compliance Guide: Bottled Water: Quality Standard: Establishing an Allowable Level for di(2... ``Bottled Water: Quality Standard: Establishing an Allowable Level for di(2- ethylhexyl)phthalate--Small... an allowable level for di(2- ethylhexyl)phthalate (DEHP). This final rule is effective April 16, 2012...

DETERMINATION OF PHTHALATES FROM BOTTLED WATER BY GC-MS

Directory of Open Access Journals (Sweden)

IRINA DUMITRAȘCU

2012-03-01

Full Text Available Determination of phthalates from bottled water by GC-MS. Phthalates are ubiquitous pollutants in the environment, due to their widespread use in the last years. These compounds are used principally as plasticizers, to impact flexibility, workability and durability to polymers but they can also be found in products such as paints, adhesives, inks and cosmetics. Phthalates are not chemically bounded to polymers; hence they are easily released and migrate into foods, beverages and drinking water from the packaging or bottling materials or manufacturing processes. This process accelerates as plastic products age and break down. With respect to their endocrine disrupting potential, phthalates such as benzyl butyl phthalate (BBP, di-butyl phthalate (DBP and di-isobutyl phthalate (DIBP have been found to elicit estrogenic responses in in vitro assays. It is possible that phthalates are a contributory factor to endocrine-mediated adverse effects observed in wildlife and humans over the past few decades. In this experiment we have analyzed the phthalates from different bottled waters purchased from the market. Determination by gas chromatography in combination with mass spectrometry detector (GC–MS in electronic ionization mode (EI with selected-ion monitoring (SIM acquisition method (GC–MS (EI–SIM has been carried out. Methods have been developed for both qualitative and quantitative analysis of phthalates. The base peak (m/z = 149 of all the phthalates was selected for the screening studies. The characteristic ions of each compound were chosen for quantitative studies.

Physicochemical and bacteriological quality of bottled drinking water in three sites of Amhara Regional State, Ethiopia.

Science.gov (United States)

Biadglegne, Fantahun; Tessema, Belay; Kibret, Mulugeta; Abera, Bayeh; Huruy, Kahsay; Anagaw, Belay; Mulu, Andargachew

2009-10-01

The consumption of bottled drinking water is becoming increasing in Ethiopia. As a result there has been a growing concern about the chemical, physical and bacteriological quality of this product. Studies on the chemical, physical and bacteriological quality of bottled water is quite scarce in Ethiopia. This study was therefore aimed to assess the physicochemical and bacteriological qualities of three factories of bottled drinking water products produced in Amhara region. A Laboratory based comparative study was conducted to evaluate the physicochemical and bacteriological quality of three factories of bottled drinking water produced in Amhara region. Analysis on the quality of bottled drinking water from the sources, wholesalers and retailers were made with World Health Organization and Quality and Standards Authority of Ethiopia recommendations. Triplicate samples from three types of bottled drinking water were randomly collected and analyzed from June, 2006 to December, 2006. A total of 108 commercial bottled drinking water samples were analyzed. The result showed that except pH of factory A all the physicochemical parameters analyzed were with in the recommended limits. The pH value of factory A tested from sources is 5.3 and from wholesalers and retailers is 5.5 and 5.3, respectively, which is below the normal value set by World Health Organization (6.5-8.0) and Quality and Standards Authority of Ethiopia (6.0-8.5). Our analyses also demonstrated that 2 (16.7%) of the samples tested from sources and 1 (8.3%) from wholesalers of factory B were contaminated with total coliforms, where as 2 (16.7%) samples from retailers were also contaminated with total coliforms. On the other hand, 1 (8.3%) of the samples tested from wholesalers and 2 (16.7%) of the samples tested from retailers of factory A were also contaminated with total coliforms. Total coliforms were not detected from all samples of factory C, fecal coliforms were not also isolated from all samples

Evaluating radon loss from water during storage in standard PET, bio-based PET, and PLA bottles

International Nuclear Information System (INIS)

Lucchetti, Carlo; De Simone, Gabriele; Galli, Gianfranco; Tuccimei, Paola

2016-01-01

Polyethylene terephthalate (PET) and polylactic acid (PLA) bottles were tested to evaluate radon loss from water during 15 days of storage. PET bottles (lower surface/volume-ratio vials) lost 0.4–7.1% of initial radon, whereas PLA bottles lost 3.7% of it. PET bottles with volume of 0.5 L, lower surface/weight ratio, and hence higher thickness display proportionally reduced radon loss. Corrections for dissolved radium are needed during analyses. Formulas for calculating degassing efficiency and water interference on electrostatic collections are developed. - Highlights: • Radon loss from water during storage in polyethylene terephthalate (PET) and polylactic acid (PLA) bottles was evaluated. • Surface/volume ratio and thickness of plastic materials were studied. • A correction for dissolved radium concentration was applied to estimate gas loss. • Proper corrections for degassing efficiency of aerators were developed. • The interference of H 2 O on radon daughter electrostatic collection was quantified.

Fluoride Content of Bottled Waters in Hong Kong and Qatar.

Science.gov (United States)

Al-Mulla, Hessa I; Anthonappa, Robert P; King, Nigel M

2016-01-01

To determine the F concentration of bottled waters that was available in Hong Kong and Qatar. The F concentrations of bottled waters collected from Hong Kong (n=81) and Qatar (n=32) were analysed. The F ion selective electrode method was used to measure the F concentration in the samples. Three measurements were obtained for every sample to ensure reproducibility and appropriate statistical analyses were employed. Qatar group: F concentrations ranged from 0.06 ppm to 3.0 ppm with a mean value of 0.8 ppm. The F concentrations displayed on the labels of the samples (60%) were significantly lower than the measured F concentration (p Qatar. The F concentrations displayed on the labels were not consistent with the measured F concentrations.

Thermal Jacket Design Using Cellulose Aerogels for Heat Insulation Application of Water Bottles

Directory of Open Access Journals (Sweden)

Hai M. Duong

2017-11-01

Full Text Available Thermal jacket design using eco-friendly cellulose fibers from recycled paper waste is developed in this report. Neoprene as an outmost layer, cellulose aerogels in the middle and Nylon as an innermost layer can form the best sandwiched laminate using the zigzag stitching method for thermal jacket development. The temperature of the ice slurry inside the water bottle covered with the designed thermal jackets remains at 0.1 °C even after 4 h, which is the average duration of an outfield exercise. Interestingly, the insulation performance of the designed thermal jackets is much better than the commercial insulated water bottles like FLOE bottles and is very competition to that of vacuum flasks for a same period of 4 h and ambient conditions.

Molecular and biochemical characterization of Pseudomonas putida isolated from bottled uncarbonated mineral drinking water

Directory of Open Access Journals (Sweden)

Tasić S.

2014-01-01

Full Text Available Pseudomonas putida belongs to a group of opportunistic pathogens that can cause disease in people with weakened or damaged immune systems. Some strains have medical significance, and for most ingestion is not the primary route of infection. If water used by predisposed subjects is contaminated by P. putida, they may become ill. The aim of this work was the biochemical and molecular characterization of strain ST3 of P. putida isolated from non-carbonated bottled drinking water from Jakov Do 4 on Mt. Vlasina. Characterization of P. putida was performed to assess the risk to human health of the indigenous strains present in the water. Biochemical characterization of strains was performed using the manual identification system ID 32 GN (BioMérieux. Identification was obtained using the database identification software ATB System (Bio-Mérieux. Molecular characterization was performed by PCR amplification and 16S rDNA “thermal cycling sequencing”. Biochemical identification of the strain ST3 was accurate (Id = 99.8%. Comparing the sequences obtained for strain ST3 with NCBI gene bank sequences for 16S rRNA, the highest similarity of our strain (96% identity with a strain of P. putida, designated as biotype A (gi|18076625|emb|AJ308311.1|.PPU308311 isolated in New Zealand, was obtained. While comparison with the NCBI collection of all deposited sequences showed that the 16S rRNA gene sequence of strain ST3 has very high homology, it is not identical, indicating indirectly that strain ST3 is an indigenous strain.

Community challenges when using large plastic bottles for Solar Energy Disinfection of Water (SODIS

Directory of Open Access Journals (Sweden)

Preeti Borde

2016-09-01

Full Text Available Abstract Background Communities living in developing countries as well as populations affected by natural or man-made disasters can be left at great risk from water related diseases, especially those spread through the faecal-oral route. Conventional water treatments such as boiling and chlorination can be effective but may prove costly for impoverished communities. Solar water disinfection (SODIS has been shown to be a cheap and effective way for communities to treat their water. The exposure to sunlight is typically carried out in small volume plastic beverage bottles (up to 2 l. Given the water requirements of consumption and basic personal hygiene, this may not always meet the needs of communities. Recent work has shown 19-L plastic water dispenser containers to be effective SODIS reactors, comparable in efficacy to PET bottles. In this paper we outline the need for studying SODIS in large volumes and discuss 4 main associated challenges. Discussion Apart from clean water needed for consumption, access to adequate water is essential for sanitation and hygiene. Contamination of treated water through unwashed hands or vessels contributes heavily to the spread of water borne pathogens in communities. Traditional water treatments such as boiling and chlorination can be effective but may prove financially burdensome for low income communities. SODIS in large vessels could be used as a simple method to meet water requirements in low income and disaster affected populations. However, there have been some concerns associated with the conventional SODIS method; we identify the main ones to be: (1 cold or cloudy weather; (2 the fear of leaching in plastic bottles; (3 water turbidity, and; (4 community acceptance. Summary The application of SODIS in large bottles like WDCs has the potential to be an efficient and cost effective method of disinfecting water, either for consumption until more rigorous water treatments can be put in place, or for

Water Jets from Bottles, Buckets, Barrels, and Vases with Holes

Science.gov (United States)

Lopac, Vjera

2015-01-01

Observation of the water jets flowing from three equidistant holes on the side of a vertical cylindrical bottle is an interesting and widely used didactical experiment illustrating the laws of fluids in motion. In this paper we analyze theoretically and numerically the ranges of the stationary water jets flowing from various rotationally symmetric…

Determination of long-lived natural Ra isotopes, 226Ra, in mineral and spring waters from Caxambu (MG) and Aguas de Lindoia (SP) spas

International Nuclear Information System (INIS)

Negrao, Sergio Garcia

2012-01-01

The aim of this work was to study the long-lived Ra isotopes, 226 Ra and 228 Ra, natural distribution in mineral and spring waters from Caxambu (MG) and Aguas de Lindoia (SP) water parks. In Caxambu mineral waters it was observed 228 Ra activity concentrations slightly higher than those of 226 Ra. The elevated content of carbonates and bicarbonates of these waters can result in an increased solubility of the both Ra isotopes and may play an important role for the fate of 228 Ra and its equilibrium distribution between solid and liquid phases. In Caxambu Thermal Spa, arithmetic mean activities ranged from 83 mBq L -1 to 3599 mBq L -1 and from 60 mBq L -1 to 4481 mBq L -1 for 226 Ra and 228 Ra, respectively. The highest 226 Ra activity was found in Venancio Spring, while the maximum 228 Ra activity value was determined in Ernestina Guedes. 228 Ra/ 226 Ra activity ratios varied from 0.079 (Conde D'Eau and Princesa Isabel Spring) to 4.2 (Mairink II Spring). In Aguas de Lindoia, arithmetic mean activities ranged from 4.6 mBq L -1 to 41 mBq L -1 and from 30 mBq L -1 to 54 mBq L -1 for 226 Ra and 228 Ra, respectively. The maximum 226 Ra activity concentration was found in the bottled mineral water Sao Jorge, while the higher 228 Ra activity concentration was determined in Santa Filomena Spring (public station 2). 228 Ra/ 226 Ra activity ratios varied from 1.2 (bottled mineral water Sao Jorge) to 9.1 (bottled mineral water Jatoba 1). This work also performed the dose assessment due to the ingestion of 226 Ra and 228 Ra in Caxambu and Aguas de Lindoia mineral and spring waters. The committed effective doses were estimated by using a conservative dosimetric model and taking into account the results over a lifetime (70 years) following intake of both long-lived Ra isotopes. The results from this radiological evaluation showed that the guidance committed effective dose level of 0.1 mSv y-1 recommended by World Health Organization was exceeded in almost all samples studied in

Gross alpha radioactivity of drinking water in Venezuela

International Nuclear Information System (INIS)

Sajo-Bohus, L.; Gomez, J.; Greaves, E.D.; Herrera, O.; Salazar, V.; Smith, A.

1997-01-01

Bottled mineral water is consumed by a large population in Venezuela. The alpha emitters concentration was measured in samples of bottled water and water springs collected near the surface. Approximately 30% of the total mineral water suppliers was monitored. a database on natural and artificial radioactivity in drinking water was produced. Results indicate that 54% of the waters sampled contain a total alpha radioactivity of less than 0.185 Bql -1 and only 12% above 0.37 Bql -1 . Our results revealed a total annual dose of 2.3 mSv year -1 . (author)

Bottled, filtered, and tap water use in Latino and non-Latino children.

Science.gov (United States)

Hobson, Wendy L; Knochel, Miguel L; Byington, Carrie L; Young, Paul C; Hoff, Charles J; Buchi, Karen F

2007-05-01

To describe bottled, filtered, and tap water consumption and fluoride use among pediatric patients; to analyze differences between ethnic and socioeconomic groups; and to describe the frequency of physician-parent discussions regarding water consumption. Convenience sample survey. An urban public health clinic. Parents attending a public health clinic. The primary outcome measure was the prevalence of tap, filtered, and bottled water use. The secondary outcome measures were supplemental fluoride use and the percentage of patients reporting discussions of water consumption with their physician. A total of 216 parents (80.5% Latino and 19.5% non-Latino) completed the survey. Of the parents, 30.1% never drank tap water and 41.2% never gave it to their children. Latino parents were less likely than non-Latino parents to drink tap water (odds ratio, 0.26; 95% confidence interval, 0.10-0.67) and less likely to give tap water to their children (odds ratio, 0.32; 95% confidence interval, 0.15-0.70). More Latinos believed that tap water would make them sick (odds ratio, 5.63; 95% confidence interval, 2.17-14.54). Approximately 40% of children who never drank tap water were not receiving fluoride supplements. Of the lowest-income families (water to their children. Of the parents surveyed, 82.5% reported that their child's physician had never discussed the type of water they should use. Many Latino families avoid drinking tap water because they fear it causes illness. Unnecessary use of bottled and filtered water is costly and may result in adverse dental health outcomes. Physicians should provide guidance to families regarding the safety, low cost, and dental health benefits of drinking tap water.

Are consumers concerned about plastic water bottles environmental impact?

OpenAIRE

Caroline Orset; Nicolas Barret; Aurélien Lemaire

2015-01-01

Although plastic induces environmental damages, almost all water bottles are made from plastic. However, these damages are more or less significant according to the plastic used. This study evaluates the consumers' willingness to pay (WTP) for different plastics used for water packaging. Successive messages emphasizing the characteristics of plastic are delivered to participants allowing explaining information influence on the consumers' WTP. We find that information has a significant effect ...

Thermophysical characteristics of plastic bottles as an element of water heat accumulators in solar greenhouses

International Nuclear Information System (INIS)

Khalimov, A. G.; Khairiddinov, B. Eh.; Kim, V. D.; Khalimov, G. G.

2012-01-01

This article considers the thermophysical and granulometric characteristics of polyethylene terephthalate (PET) plastic bottles filled with water. The given figures allow one to conduct calculations of thermal plastic bottles as heat storage elements for solar greenhouses. (author)

Qualidade microbiológica de águas minerais Microbiological quality of mineral waters

Directory of Open Access Journals (Sweden)

Anderson de S. Sant´Ana

2003-12-01

Full Text Available Quarenta e quatro amostras de água mineral envasadas, de diferentes marcas, foram examinadas quanto à contaminação por coliformes totais, E.coli, Pseudomonas aeruginosa, Enterococos, Clostrídios sulfito redutores a 46ºC, de acordo com o preconizado pela RDC 54/00 do Ministério da Saúde. Empregou-se a metodologia da membrana filtrante. Em nenhuma das amostras foi detectada a presença de clostrídios sulfito redutores a 46ºC, Pseudomonas aeruginosa e enterococos. A contaminação por coliformes totais e E.coli, detectada em 25% e 20,4% das amostras, respectivamente, sugere falhas higiênicas ao longo do processo e contaminação fecal recente. Tais amostras apresentam-se em desacordo com os padrões microbiológicos legais estabelecidos pela Legislação Brasileira. Devem-se adotar práticas higiênicas rigorosas em todo processamento, com o objetivo de obter-se produtos seguros, já que tratamentos não podem ser utilizados visando a redução/eliminação da contaminação.Forty four samples of bottled mineral water, from different brands, were examined for total coliforms, E.coli, Pseudomonas aeruginosa, enterococci and sulfide reducing clostridia, according to the Brazilian legal standard. The membrane-filter was the metodology used. None of the samples showed contamination by sulfide reducing clostridia, enterococci and Pseudomonas aeruginosa. Total coliforms and E.coli were detected in 25% and 20.4% of the samples respectively sugesting poor hygiene along the process and recent faecal contamination. Such samples were in disaccordance with the Brazilian microbiological specifications. The bottled mineral water must be produced under good manufacturing practices with the objective to obtain safe products, since treatments can not be used to reduce/eliminate the contamination.

Ancient water bottle use and polycyclic aromatic hydrocarbon (PAH) exposure among California Indians: a prehistoric health risk assessment.

Science.gov (United States)

Sholts, Sabrina B; Smith, Kevin; Wallin, Cecilia; Ahmed, Trifa M; Wärmländer, Sebastian K T S

2017-06-23

Polycyclic aromatic hydrocarbons (PAHs) are the main toxic compounds in natural bitumen, a fossil material used by modern and ancient societies around the world. The adverse health effects of PAHs on modern humans are well established, but their health impacts on past populations are unclear. It has previously been suggested that a prehistoric health decline among the native people living on the California Channel Islands may have been related to PAH exposure. Here, we assess the potential health risks of PAH exposure from the use and manufacture of bitumen-coated water bottles by ancient California Indian societies. We replicated prehistoric bitumen-coated water bottles with traditional materials and techniques of California Indians, based on ethnographic and archaeological evidence. In order to estimate PAH exposure related to water bottle manufacture and use, we conducted controlled experiments to measure PAH contamination 1) in air during the manufacturing process and 2) in water and olive oil stored in a completed bottle for varying periods of time. Samples were analyzed with gas chromatography/mass spectrometry (GC/MS) for concentrations of the 16 PAHs identified by the US Environmental Protection Agency (EPA) as priority pollutants. Eight PAHs were detected in concentrations of 1-10 μg/m 3 in air during bottle production and 50-900 ng/L in water after 2 months of storage, ranging from two-ring (naphthalene and methylnaphthalene) to four-ring (fluoranthene) molecules. All 16 PAHs analyzed were detected in olive oil after 2 days (2 to 35 μg/kg), 2 weeks (3 to 66 μg/kg), and 2 months (5 to 140 μg/kg) of storage. For ancient California Indians, water stored in bitumen-coated water bottles was not a significant source of PAH exposure, but production of such bottles could have resulted in harmful airborne PAH exposure.

Drinking water quality from the aspect of element concentrations

International Nuclear Information System (INIS)

Chiba, M.; Shinohara, A.; Sekine, M.; Hiraishi, S.

2006-01-01

Drinking water in developed countries is usually treated by the water-purification system, while in developing countries untreated natural water such as well water, river water, rain water, or pond water are used. On the other hand, many kinds of mineral water bottled in plastic containers are sold as drinking water with or without gas in urban areas in many countries. Seawater under hundreds meters from the surface is also bottled and sold as drinking water with advertising good mineral balance. Various element concentrations in water samples for drinking were analyzed, and then it was considered the effects of elements on human health. (author)

Tap versus bottled water consumption: The influence of social norms, affect and image on consumer choice.

Science.gov (United States)

Etale, Anita; Jobin, Marilou; Siegrist, Michael

2018-02-01

What drives consumers to choose bottled water instead of tap water where the latter is safe, accessible, costs far less, and in spite of its environmental impacts? This research investigates the influence of hitherto unexplored psychological drivers in an attempt to generate a more holistic understanding of the phenomenon, and strategies for designing more effective consumption reduction campaigns. Using data from an internet survey of Swiss and German respondents (N = 849) we investigated the role of, social norms, affect and image on water consumption. Results suggest that these psychological factors play a role in water consumption choice. Convenience was the only contextual predictor - the inconvenience of transporting bottled water has a negative effect on its consumption, and a positive effect on tap water consumption. Although concern about the effect of bottled water on the environment was not a significant predictor of tap water consumption, we found that for some people, a link exists between environmental concern and consumption choice. Ways through which consumers may be more effectively influenced towards environmentally-friendly consumption are discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Is container type the biggest predictor of trace element and BPA leaching from drinking water bottles?

Science.gov (United States)

Rowell, Candace; Kuiper, Nora; Preud'Homme, Hugues

2016-07-01

The knowledge-base of bottled water leachate is highly contradictory due to varying methodologies and limited multi-elemental and/or molecular analyses; understanding the range of contaminants and their pathways is required. This study determined the leaching potential and leaching kinetics of trace elements, using consistent comprehensive quantitative and semi-quantitative (79 elements total) analyses, and BPA, using isotopic dilution and MEPS pre-concentration with UHPLC-ESI-QTOF. Statistical methods were used to determine confounders and predictors of leaching and human health risk throughout 12days of UV exposure and after exposure to elevated temperature. Various types of water were used to assess the impact of water quality. Results suggest Sb leaching is primarily dependent upon water quality, not container type. Bottle type is a predictor of elemental leaching for Pb, Ba, Cr, Cu, Mn and Sr; BPA was detected in samples from polycarbonate containers. Health risks from the consumption of bottled water increase after UV exposure. Copyright © 2016 Elsevier Ltd. All rights reserved.

Radium removal from Australian spa waters

International Nuclear Information System (INIS)

Dickson, B.L.; Meakins, R.L.; Bland, C.J.

1982-01-01

The dissolved radium content of some mineral spring waters in Victoria and Queensland has been found to exceed the maximum permissible concentration in drinking water. Activities in excess of 40 pCi/1 were measured in some bottles. Studies revealed that the dissolved radium content decreased markedly if the spring water was aerated and filtered prior to bottling. The sediment removed contained ferric hydroxide which is a natural scavenging agent for radium. The formation of such sediments in storage tanks and their removal prior to bottling may create a possible radiation hazard

Determination of water vapor transmission rate (WVTR) of HDPE bottles for pharmaceutical products.

Science.gov (United States)

Chen, Yisheng; Li, Yanxia

2008-06-24

The objective of this study was to investigate the effects of experimental conditions for measuring the water vapor transmission rate (WVTR) of high-density polyethylene (HDPE) bottles using a steady-state sorption method. Bottles were filled with desiccant, closed with caps and heat induction sealed, and then stored in stability chambers at controlled temperature and relative humidity. Weight gain of the bottles was determined every 1 or 2 weeks until a linear weight gain profile was obtained. WVTR of the bottles was determined from the slope of the linear portion of the weight gain versus time profile. The effects of desiccants and temperature/humidity were studied. Results show that, with a sufficient amount of anhydrous calcium chloride in bottles, a negligibly low and sufficiently constant headspace humidity is maintained, and a steady-state permeation rate is achieved. For all 8 sizes of bottles used in this study, steady-state was achieved in 1 or 2 weeks after the experiment was started. This method provided reproducible WVTR data for HDPE bottles. Apparent moisture permeability of all 8 sizes of bottles was (2.3+/-0.3)x10(-7), (2.6+/-0.2)x10(-7), and (3.4+/-0.2)x10(-7)cm(2)/s at 25 degrees C, 30 degrees C, 40 degrees C, respectively. Moisture permeability determined from the current study was similar to data reported in the literature, indicating that the steady-state weight gain method can be used to obtain reliable WVTR of containers for pharmaceutical products.

Effects of storage temperature and time of antimony release from PET bottles into drinking water in China.

Science.gov (United States)

Qiao, Fei; Lei, Kun; Li, Zicheng; Liu, Qing; Wei, Zhanliang; An, Lihui; Qi, Hongli; Cui, Song

2018-01-01

Antimony (Sb) concentrations were measured in 10 brands of PET bottled drinking water available in supermarkets in China. To simulate general storage habits based on market research, these PET bottles with drinking water were stored for 4 weeks in a lab or a car trunk during the summer. Although the PET package material of brand A had the lowest Sb level (142.71 ± 29.81 μg/g), it showed a significant increase in Sb concentrations when stored in both the car trunk and the lab. There was significant release of Sb from the PET bottles into the water following 24 h of incubation at ≥ 40 °C (40, 50, 60, and 70 °C), especially at 70 °C. The potential health risk of Sb release from PET bottles was calculated based on daily intake values and determined to be acceptable for consumers under normal storage conditions.

A survey of the microbiological quality of bottled water sold in Peshawar city of north west frontier province of Pakistan

International Nuclear Information System (INIS)

Alizai, M.N.; Abid, H.; Ali, J.; Ibrahim, M.

2010-01-01

Nine brands of domestic bottled water purchased from various locations of Peshawar City were microbiological analysed with in three hours of collection for the test (i.e.) Total Coliforms, Total Fecal Coliform, E,coli and Total Plant Count. The results indicated that 33.3% of bottled water was within the acceptable limit set by World Health Organization (WHO) and Pakistan Standard Quality Control Authority (PSQCA) guideline whereas 66.6% bottled water samples were unsafe for human consumption. (author)

Ultimate resources of drinking water in the event of a major pollution crisis: the role of bottled water

International Nuclear Information System (INIS)

Collin, J.J.; Comte, J.P.; Daum, J.R.; Lopoukhine, M.; Mesny, M.

1995-01-01

In the event of a serious and widespread pollution incident - on the level of the ''Chernobyl cloud'' - most of the drinking water resources in France could be contaminated : surface water immediately, ground water in a few days... or a few months. Therefore on the initiative of the Ministry of the Environment's Director for Defence, a study has been initiated as to what might be qualified as ''final emergency resources''. An inventory and map of protected resources have been prepared. In this context it seems reasonable to show bottled water as a resource meeting the necessary protection criteria. However it seems that these criteria are not all, nor always, relevant for defining a ''ultimate emergency resource'' not contaminated by a major incident. This article outlines a typology of situations and defines the main criteria necessary for bottled water to be able to constitute an ultimate resource

76 FR 64810 - Beverages: Bottled Water Quality Standard; Establishing an Allowable Level for di(2-ethylhexyl...

Science.gov (United States)

2011-10-19

.... FDA 1993-N-0259 (Formerly Docket No. 1993N-0085)] Beverages: Bottled Water Quality Standard... evidence from two studies puts previous concerns to rest concerning the effects of DEHP consumption in... increase costs for consumers for beverages packaged in plastic bottles. However, this rule does not...

210Pb and 210Po Determination in Bottled Water Available on the Croatian Market

International Nuclear Information System (INIS)

Rogic, M.; Rozmaric Macefat, M.; Benedik, Lj.; Strok, M.

2011-01-01

An alpha emitting radionuclide 210Po and beta emitting radionuclide 210Pb are decay products of 238U. Due to their nuclear properties they are considered as radionuclides with the highest radiotoxicity and contribute significantly to the internal dose to the population received by drinking water. For radiological impact assessment 210Pb and 210Po must be measured routinely and accurately, with low detection limits. The aim of our study was determination of activity concentrations of 210Pb and 210Po in bottled drinking and mineral waters available on Croatian market. For their determination a procedure for their simultaneous separation from the water samples was used. After addition of 209Po tracer and lead carrier, radionuclides were preconcentrated from large volume by MnO 2 and their separation from interfering elements by Sr resin was done. 210Po source for alpha-particle spectrometric measurement was prepared by selfdeposition on silver disc, while lead was precipitated as lead sulphate and the beta activity of its daughter 210Bi was counted on a beta proportional counter. The results obtained show that values for activity concentrations of 210Pb and 210Po in all examined waters are in accordance with allowed activity concentration according to the European Commission Recommendation 2001/928/Euratom and Guidelines for Drinking Water Quality, published by WHO in 2006. (author)

Speciation of inorganic antimony in polyethylene terephthalate (PET) bottled water using hydride generation atomic absorption spectrophotometry (HG-AAS)

International Nuclear Information System (INIS)

Markwo, Ali

2015-07-01

Antimony (Sb) is a regulated drinking water contaminant that has been found to leach from polyethylene terephthalate (PET) plastic containers into the waters stored in them. The common inorganic species of antimony in water are Sb(III) and Sb(V), with the former being more toxic and the latter being more soluble. In order to assess the extent to which waters stored in PET bottles are contaminated with inorganic Sb and to further examine the effect of typical storage conditions on migration rates, speciation analysis of inorganic Sb using hydride generation atomic absorption spectrophotometry (HG-AAS) was undertaken on selected PET plastic bottled waters marketed in the Greater Accra Region of Ghana. Six brands of PET plastic bottled waters were obtained at source on the day of packaging, and analyses undertaken on samples of the waters stored in the plastic containers at intervals of four weeks for twelve weeks, under three carefully chosen storage conditions distinctive of bottled water usage. Selected physicochemical properties of samples of the waters stored in the plastic containers and total Sb of samples of the plastic containers were also determined to discover the effect of some physical properties and certain major ions, and the influence of the different quality PET plastic types on Sb migration respectively. The study revealed amounts of total Sb in the PET plastic containers of the 6 brands ranging from 123.46 mg/kg to 146.45 mg/kg. The selected physicochemical properties of the waters stored in the PET plastic containers considered were pH (6.78 – 7.43), Ca2+ (1.61 – 12.39 mg/L), Mg2+ (1.00 – 4.96 mg/L), HCO3− (6.18 – 55.41 mg/L) and TDS (8.70 – 70.40 mg/L)). PET bottled waters of 5 out of the 6 brands contained Sb (initial total Sb ranging from 1.11 – 14.65 μg/L) before storage. Total Sb concentrations of the waters stored in the plastic containers were observed to increase with storage time under all the three storage conditions for

Dimensioning of a solar water heater made from PET bottles; Dimensionamento de um aquecedor solar de agua feito com garrafas PET

Energy Technology Data Exchange (ETDEWEB)

Bertoleti, Pedro Henrique Fonseca; Souza, Teofilo Miguel de [Universidade Estadual Paulista (UNESP), Guaratingueta, SP (Brazil). Centro de Energias Renovaveis

2008-07-01

This document show the solar water heater made of PET bottles, a simple-construction solar water heater that try to give us two important solutions, water heating using solar energy and reutilization of the PET bottles left in the nature. Also, it will be showed how to do the dimensioning of it. Based on the showed dimensioning a application / software is developed and after that simulations are made using the application to provide how is the economy if it's used this kind of solar water heater and their environmental contribution by reutilization of the PET bottles abandoned in the nature. For example, in a common home the economy is about 45% of the electricity bill considering that the warmed water is used just to take a shower. So, the conclusion is: the solar water heater made by PET bottles is a very relevant equipment to the use of the solar energy, to useful applications and environmental contribution. (author)

Hydrokinesitherapy in thermal mineral water

Directory of Open Access Journals (Sweden)

Rendulić-Slivar Senka

2013-01-01

Full Text Available The treatment of clients in health spa resorts entails various forms of hydrotherapy. Due to specific properties of water, especially thermal mineral waters, hydrokinesitherapy has a positive effect on the locomotor system, aerobic capabilities of organism and overall quality of human life. The effects of use of water in movement therapy are related to the physical and chemical properties of water. The application of hydrotherapy entails precautionary measures, with an individual approach in assessment and prescription. The benefits of treatment in thermal mineral water should be emphasized and protected, as all thermal mineral waters differ in composition. All physical properties of water are more pronounced in thermal mineral waters due to its mineralisation, hence its therapeutical efficiency is greater, as well.

Field comparison of solar water disinfection (SODIS) efficacy between glass and polyethylene terephalate (PET) plastic bottles under sub-Saharan weather conditions.

Science.gov (United States)

Asiimwe, J K; Quilty, B; Muyanja, C K; McGuigan, K G

2013-12-01

Concerns about photodegradation products leaching from plastic bottle material into water during solar water disinfection (SODIS) are a major psychological barrier to increased uptake of SODIS. In this study, a comparison of SODIS efficacy using glass and plastic polyethylene terephalate (PET) bottles was carried out under strong real sunlight and overcast weather conditions at Makerere University in central Uganda. Both clear and turbid natural water samples from shallow wells and open dug wells, respectively, were used. Efficacy was determined from the inactivation of a wild strain of Escherichia coli in solar-exposed contaminated water in both glass and PET bottles. The studies reveal no significant difference in SODIS inactivation between glass and PET bottles (95% CI, p > 0.05), for all water samples under the different weather conditions except for clear water under overcast conditions where there was a small but significant difference (95% CI, p = 0.047) with less viable bacterial counts in PET bottles at two intermediate time points but not at the end of the exposure. The results demonstrate that SODIS efficacy in glass under tropical field conditions is comparable to PET plastic. SODIS users in these regions can choose either of reactors depending on availability and preference of the user.

Insulated Containers for Bottled Water (ICB)-Performance Evaluation

Science.gov (United States)

2017-04-21

Plastic   Wrapped  Cordura  Rubberized traction pad  PE  Plastic   Liner  No  Yes  Yes  No  Safe Tie‐Down  Capability  Yes  Yes  Yes  No  Easy Access...mounted Soldiers. The ICBs are lighter, require less storage space, and have more effective tie-down characteristics than coolers often used to carry...bottled water in vehicles. The performance of the ICBs and a commonly used cooler was assessed to determine whether the easier-to-stow ICBs would be as

Physicochemical properties and the concentration of anions, major and trace elements in groundwater, treated drinking water and bottled drinking water in Najran area, KSA

Science.gov (United States)

Brima, Eid I.

2017-03-01

Basic information about major elements in bottled drinking water is provided on product labels. However, more information is needed about trace elements in bottled drinking water and other sources of drinking water to assess its quality and suitability for drinking. This is the first such study to be carried out in Najran city in the Kingdom of Saudi Arabia (KSA). A total of 48 water samples were collected from different sources comprising wells, stations for drinking water treatment and bottled drinking water (purchased from local supermarkets). The concentrations of 24 elements [aluminum (Al), arsenic (As), barium (Ba), calcium (Ca), cadmium (Cd), cobalt (Co), chromium (Cr), cesium (Cs), copper (Cu), iron (Fe), potassium (K), magnesium (Mg), manganese (Mn), molydenum (Mo), sodium (Na), nickel (Ni), lead (Pb), rubidium (Rb), selenium (Se), strontium (Sr), titanium (Ti), vanadium (V), uranium (U) and zinc (Zn)] were determined by inductively coupled plasma-mass spectrometry (ICP-MS). Anions (chlorine (Cl-), fluoride (F-), sulfate (SO4 2-) and nitrate (NO3 -) were determined by ion chromatography (IC). Electrical conductivity (EC), pH, total dissolved salts (TDS) and total hardness (TH) were also measured. All parameters of treated drinking water and bottled drinking water samples did not exceed the World Health Organization (WHO) 2008, US Environmental Protection Agency (USEPA 2009), Gulf Cooperation Council Standardization Organization (GSO) 2008 and Saudi Arabian Standards Organization (SASO) 1984 recommended guidelines. It is noteworthy that groundwater samples were not used for drinking purpose. This study is important to raise public knowledge about drinking water, and to promote public health.

Impact of temperature and storage time on the migration of antimony from polyethylene terephthalate (PET) containers into bottled water in Qatar.

Science.gov (United States)

Al-Otoum, Fatima; Al-Ghouti, Mohammad A; Costa, Ozeas S; Khraisheh, Majeda

2017-11-12

Prosperity in Qatar and the consequent stresses on water resources resulted in a sustainable increase in the bottled drinking water market. Reports on health concerns and possible migration of chemicals from the plastic material into the water have driven the current investigation. This study aims to address the extent of antimony (Sb) leaching from polyethylene terephthalate (PET) water bottles subject to temperature variations (24-50 °C) due to Qatar's hot climate and improper storage conditions. A representative basket including 66 different imported and locally produced water bottles was considered. The concentrations of Sb in bottled water ranged from 0.168 to 2.263 μg/L at 24 °C and from 0.240 to 6.110 μg/L at 50 °C. Antimony concentrations in PET bottles at 24 °C was significantly lower than those at 50 °C (p = 0.0142), indicating that the temperature was a principal factor affecting the release of Sb from the plastic into the water. Although the detected Sb amounts were below the guidelines endorsed by WHO and Qatar (standard 5 μg/L) at 24 °C, the concentration measured at 50 °C was higher than the recommended WHO values (6.11 μg/L).

Using an interactive water bottle to target fluid adherence in pediatric kidney transplant recipients: a pilot study.

Science.gov (United States)

Kullgren, Kristin A; Scholl, Penny; Kidwell, Kelley M; Hmiel, S Paul

2015-02-01

Hydration is important post-renal transplant to maintain adequate renal perfusion and graft function. Adherence to fluid recommendations is challenging given barriers to staying hydrated. There are no studies of adherence to fluid intake recommendations following pediatric renal transplant. Through this pilot study, we sought to determine whether the use of a commercially available interactive water bottle would lead to better adherence to recommended fluid intake and improved kidney functioning post-transplant relative to standard of care. Participants included 32 youth ages 7-19 ≥1 month post-kidney transplant randomized to the intervention (HydraCoach(®) water bottle) or standard education control group. Laboratory records were reviewed for serum chemistries (Na, BUN, creatinine) at baseline and one-month follow-up, and participants recorded daily fluid intake for 28 days. Those in the intervention group were significantly more likely to meet or exceed their fluid target, but this did not translate into better kidney functioning. Participants in the intervention group largely reported satisfaction with the water bottle and were likely to continue its use. While an interactive water bottle providing real-time feedback may be a promising intervention to help pediatric kidney transplant patients meet fluid goals, it did not appear to impact kidney function. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Impact of temperature and storage duration on the chemical and odor quality of military packaged water in polyethylene terephthalate bottles

Energy Technology Data Exchange (ETDEWEB)

Greifenstein, Michael, E-mail: Michael.Greifenstein@us.army.mil [Department of Preventive Medicine and Biometrics, 4301 Jones Bridge Road, Uniformed Services University of the Health Sciences, Bethesda, MD 20814 (United States); White, Duvel W., E-mail: duvel.white@us.army.mil [Department of Preventive Medicine and Biometrics, 4301 Jones Bridge Road, Uniformed Services University of the Health Sciences, Bethesda, MD 20814 (United States); Stubner, Alex, E-mail: alex.stubner@usuhs.edu [Department of Preventive Medicine and Biometrics, 4301 Jones Bridge Road, Uniformed Services University of the Health Sciences, Bethesda, MD 20814 (United States); Hout, Joseph, E-mail: joseph.hout@usuhs.edu [Department of Preventive Medicine and Biometrics, 4301 Jones Bridge Road, Uniformed Services University of the Health Sciences, Bethesda, MD 20814 (United States); Whelton, Andrew J., E-mail: ajwhelton@southalabama.edu [Department of Civil Engineering, 3021 Shelby Hall, University of South Alabama, Mobile, AL 36688 (United States)

2013-07-01

The impact of temperature and storage time on military packaged water (MPW) quality was examined at four temperatures (23.0 °C to 60.0 °C) for 120 days. Polyethylene terephthalate (PET) bottles were filled in California and Afghanistan with unbuffered water treated by reverse osmosis. The US military's water pH long-term potability standard was exceeded, and US Food and Drug Administration (USFDA) and US Environmental Protection Agency (USEPA) drinking water pH and odor intensity limits were also exceeded. During a 70 day exposure period, Port Hueneme MPW total organic carbon and total trihalomethane levels increased from < 0.25 mg/L to 2.0 ± 0.0 mg/L and < 0.05 μg/L to 51.5 ± 2.1 μg/L, respectively. PET released organic contaminants into MPW and residual disinfectant generated trihalomethane contaminants. After 14 days at 37.7 °C and 60.0 °C, Afghanistan MPW threshold odor number values were 8.0 and 8.6, respectively. Total organic carbon concentration only increased with exposure duration at 60.0 °C. Acetaldehyde and formaldehyde contaminants were not detected likely due to the high method detection limits applied in this study. Phthalate contaminants detected and their maximum levels were butylbenzylphthalate (BBP) 0.43 μg/L, di-n-butylphthalate (DnBP) 0.38 μg/L, di(2-ethylhexyl)phthalate (DEHP) 0.6 μg/L, and diethylphthalate (DEP) 0.32 μg/L. Antimony was only detected in 60.0 °C Afghanistan MPW on Day 28 and beyond, and its maximum concentration was 3.6 ± 0.3 μg/L. No antimony was found in bottles exposed to lesser temperatures. Environmental health, PET synthesis and bottle manufacturers, and bottle users can integrate results of this work to improve health protective decisions and doctrine. - Highlights: • Temperature and storage time impacted military bottled water quality up to 60 °C. • The chemical quality of water bottled in California and Afghanistan was affected. • Drinking water pH and odor intensity limits were also

An evaluation of the migration of antimony from polyethylene terephthalate (PET) plastic used for bottled drinking water

Energy Technology Data Exchange (ETDEWEB)

Chapa-Martínez, C.A.; Hinojosa-Reyes, L.; Hernández-Ramírez, A.; Ruiz-Ruiz, E.; Maya-Treviño, L.; Guzmán-Mar, J.L., E-mail: jorge.guzmanmr@uanl.edu.mx

2016-09-15

The leaching of antimony (Sb) from polyethylene terephthalate (PET) bottling material was assessed in twelve brands of bottled water purchased in Mexican supermarkets by atomic fluorescence spectrometry with a hydride generation system (HG-AFS). Dowex® 1X8-100 ion-exchange resin was used to preconcentrate trace amounts of Sb in water samples. Migration experiments from the PET bottle material were performed in water according to the following storage conditions: 1) temperature (25 and 75 °C), 2) pH (3 and 7) and 3) exposure time (5 and 15 days), using ultrapure water as a simulant for liquid foods. The test conditions were studied by a 2{sup 3} factorial experimental design. The Sb concentration measured in the PET packaging materials varied between 73.0 and 111.3 mg/kg. The Sb concentration (0.28–2.30 μg/L) in all of the PET bottled drinking water samples examined at the initial stage of the study was below the maximum contaminant level of 5 μg/L prescribed by European Union (EU) regulations. The parameters studied (pH, temperature, and storage time) significantly affected the release of Sb, with temperature having the highest positive significant effect within the studied experimental domain. The highest Sb concentration leached from PET containers was in water samples at pH 7 stored at 75 °C for a period of 5 days. The extent of Sb leaching from the PET ingredients for different brands of drinking water can differ by as much as one order of magnitude in experiments conducted under the worst-case conditions. The chronic daily intake (CDI) caused by the release of Sb in one brand exceeded the Environmental Protection Agency (USEPA) regulated CDI value of 400 ng/kg/day, with values of 514.3 and 566.2 ng/kg/day for adults and children. Thus, the appropriate selection of the polymer used for the production of PET bottles seems to ensure low Sb levels in water samples. - Highlights: • The PET safety due to the release of Sb was evaluated in Mexican water PET

An evaluation of the migration of antimony from polyethylene terephthalate (PET) plastic used for bottled drinking water

International Nuclear Information System (INIS)

Chapa-Martínez, C.A.; Hinojosa-Reyes, L.; Hernández-Ramírez, A.; Ruiz-Ruiz, E.; Maya-Treviño, L.; Guzmán-Mar, J.L.

2016-01-01

The leaching of antimony (Sb) from polyethylene terephthalate (PET) bottling material was assessed in twelve brands of bottled water purchased in Mexican supermarkets by atomic fluorescence spectrometry with a hydride generation system (HG-AFS). Dowex® 1X8-100 ion-exchange resin was used to preconcentrate trace amounts of Sb in water samples. Migration experiments from the PET bottle material were performed in water according to the following storage conditions: 1) temperature (25 and 75 °C), 2) pH (3 and 7) and 3) exposure time (5 and 15 days), using ultrapure water as a simulant for liquid foods. The test conditions were studied by a 2 3 factorial experimental design. The Sb concentration measured in the PET packaging materials varied between 73.0 and 111.3 mg/kg. The Sb concentration (0.28–2.30 μg/L) in all of the PET bottled drinking water samples examined at the initial stage of the study was below the maximum contaminant level of 5 μg/L prescribed by European Union (EU) regulations. The parameters studied (pH, temperature, and storage time) significantly affected the release of Sb, with temperature having the highest positive significant effect within the studied experimental domain. The highest Sb concentration leached from PET containers was in water samples at pH 7 stored at 75 °C for a period of 5 days. The extent of Sb leaching from the PET ingredients for different brands of drinking water can differ by as much as one order of magnitude in experiments conducted under the worst-case conditions. The chronic daily intake (CDI) caused by the release of Sb in one brand exceeded the Environmental Protection Agency (USEPA) regulated CDI value of 400 ng/kg/day, with values of 514.3 and 566.2 ng/kg/day for adults and children. Thus, the appropriate selection of the polymer used for the production of PET bottles seems to ensure low Sb levels in water samples. - Highlights: • The PET safety due to the release of Sb was evaluated in Mexican water PET

Iodine mineral waters

Directory of Open Access Journals (Sweden)

Iluta Alexandru

2011-11-01

Full Text Available Iodine mineral waters are found especially in sub-Carpathian region, also in regions with Salif deposits. Waters are currently used iodine in drinking cure for chaps and Basedow. Are also indicated in balneology. Iodine water containing at least 1 mg L, there is pure iodine is usually given the nature of other types of mineral waters further: sodium chlorinated water (Bazna (50-70 mg iodine / l, Baile Govora (50 - 70 mg / l, Bălţăteşti (4-5 mg / l, salted Monteoru (30 mg / l, mine water mixed alkaline chlorination, sulphate, which are indicated for crenoterapie (hypo or isotonic to the bathrooms Olăneşti or Călimăneşti-Căciulata.

Characteristics of bacterial and fungal growth in plastic bottled beverages under a consuming condition model.

Science.gov (United States)

Watanabe, Maiko; Ohnishi, Takahiro; Araki, Emiko; Kanda, Takashi; Tomita, Atsuko; Ozawa, Kazuhiro; Goto, Keiichi; Sugiyama, Kanji; Konuma, Hirotaka; Hara-Kudo, Yukiko

2014-01-01

Microbial contamination in unfinished beverages can occur when drinking directly from the bottle. Various microorganisms, including foodborne pathogens, are able to grow in these beverages at room temperature or in a refrigerator. In this study, we elucidated the characteristics of microorganism growth in bottled beverages under consuming condition models. Furthermore, we provide insight into the safety of partially consumed bottled beverages with respect to food hygiene. We inoculated microorganisms, including foodborne pathogens, into various plastic bottled beverages and analysed the dynamic growth of microorganisms as well as bacterial toxin production in the beverages. Eight bottled beverage types were tested in this study, namely green tea, apple juice drink, tomato juice, carbonated drink, sport drink, coffee with milk, isotonic water and mineral water, and in these beverages several microorganism types were used: nine bacteria including three toxin producers, three yeasts, and five moulds. Following inoculation, the bottles were incubated at 35°C for 48 h for bacteria, 25°C for 48 h for yeasts, and 25°C for 28 days for moulds. During the incubation period, the number of bacteria and yeasts and visible changes in mould-growth were determined over time. Our results indicated that combinations of the beverage types and microorganism species correlated with the degree of growth. Regarding factors that affect the growth and toxin-productivity of microorganisms in beverages, it is speculated that the pH, static/shaking culture, temperature, additives, or ingredients, such as carbon dioxide or organic matter (especially of plant origin), may be important for microorganism growth in beverages. Our results suggest that various types of unfinished beverages have microorganism growth and can include food borne pathogens and bacterial toxins. Therefore, our results indicate that in terms of food hygiene it is necessary to consume beverages immediately after opening

Investigating the Concentration of Heavy Metals in Bottled Water and Comparing with its Standard: Case Study

Directory of Open Access Journals (Sweden)

Mohammad Hossien Salmani

2017-09-01

Results: Brand No. 1, the concentration of zinc ion was larger in Brand 2 while in Brand No. 2 had larger copper, nickel, and aluminum ions. The results indicated that the concentration of the measured metal ions were below the allowable limit of drinking water standard across all of the studied samples. Conclusion: Based on the obtained results from the investigated parameters, it can be concluded that the bottled water of both brands poses no health issue and is drinkable. Considering the changes in the concentration of ions and the increasing trend of consumption of bottled waters, their monitoring and qualitative control of pollutants are very crucial in terms of public health.

Oscillations in a half-empty bottle

Science.gov (United States)

Bourges, Andréane; Chardac, Amélie; Caussarieu, Aude; Plihon, Nicolas; Taberlet, Nicolas

2018-02-01

When a half-empty bottle of water is pushed to roll on a flat surface, the oscillations of the fluid inside the bottle induce an overall jerky motion. These velocity fluctuations of the bottle are studied through simple laboratory experiments accessible to undergraduate students and can help them to grasp fundamental concepts in mechanics and hydrodynamics. We first demonstrate through an astute experiment that the rotation of the fluid and the bottle is decoupled. The equations of motion are then derived using a mechanical approach, while the hydrodynamics of the fluid motion is explained. Finally, the theory is tested against two benchmark experiments.

Effect of temperature on the release of intentionally and non-intentionally added substances from polyethylene terephthalate (PET) bottles into water: chemical analysis and potential toxicity.

Science.gov (United States)

Bach, Cristina; Dauchy, Xavier; Severin, Isabelle; Munoz, Jean-François; Etienne, Serge; Chagnon, Marie-Christine

2013-08-15

The purpose of this study was to investigate the impact of temperature on the release of PET-bottle constituents into water and to assess the potential health hazard using in vitro bioassays with bacteria and human cell lines. Aldehydes, trace metals and other compounds found in plastic packaging were analysed in PET-bottled water stored at different temperatures: 40, 50, and 60°C. In this study, temperature and the presence of CO2 increased the release of formaldehyde, acetaldehyde and antimony (Sb). In parallel, genotoxicity assays (Ames and micronucleus assays) and transcriptional-reporter gene assays for estrogenic and anti-androgenic activity were performed on bottled water extracts at relevant consumer exposure levels. As expected, and in accordance with the chemical formulations specified for PET bottles, neither phthalates nor UV stabilisers were present in the water extracts. However, 2,4-di-tert-butylphenol, a degradation compound of phenolic antioxidants, was detected. In addition, an intermediary monomer, bis(2-hydroxyethyl)terephthalate, was found but only in PET-bottled waters. None of the compounds are on the positive list of EU Regulation No. 10/2011. However, the PET-bottled water extracts did not induce any cytotoxic, genotoxic or endocrine-disruption activity in the bioassays after exposure. Copyright © 2013 Elsevier Ltd. All rights reserved.

Quantitative Determination of Arsenic in Bottled Drinking Water Using Atomic Absorption Spectroscopy

Directory of Open Access Journals (Sweden)

Maria Guţu Claudia

2013-10-01

Full Text Available Background: Many studies have been performed in the past few years, to determine arsenic speciation in drinking water, food chain and environment, arsenic being a well-recognized carcinogenic and toxic agent mainly in its inorganic species. The instrumental techniques used for arsenic determination, such as hydride generation atomic absorption spectrometry (HGAAS, graphite furnace atomic absorption spectrometry (GFAAS and inductively coupled plasma mass spectrometry (ICP-MS, can provide a great sensitivity only on the total amount. Objective: The aim of this study was to develop a simple and rapid method and to analyze the concentration of total inorganic arsenic in bottled drinking water. Methods: Total arsenic was determined in samples from six different types of commercially available bottled drinking water using atomic absorption spectrometry with electrothermal or hydride generation vaporisation. All drinking water samples were acidified with 0.1M nitric acid to match the acidity of the standards. Results: The method was linear within the studied range (1-5 μg/L, R = 0.9943. The quantification limits for arsenic determination were 0.48 μg/L (HGAAS and 0.03 μg/L (GFAAS. The evaluated arsenic content in drinking water was within the accepted limits provided by law. Conclusions: A simple and sensitive method for the quantification of arsenic in drinking water using atomic absorbtion spectroscopy was described, which can be further used in toxicological studies. As an additional advantage, the system is very fast, efficient and environmental friendly

Microbiological assessment of house and imported bottled water by comparison of bacterial endotoxin concentration, heterotrophic plate count, and fecal coliform count.

Science.gov (United States)

Reyes, Mayra I; Pérez, Cynthia M; Negrón, Edna L

2008-03-01

Consumers increasingly use bottled water and home water treatment systems to avoid direct tap water. According to the International Bottled Water Association (IBWA), an industry trade group, 5 billion gallons of bottled water were consumed by North Americans in 2001. The principal aim of this study was to assess the microbial quality of in-house and imported bottled water for human consumption, by measurement and comparison of the concentration of bacterial endotoxin and standard cultivable methods of indicator microorganisms, specifically, heterotrophic and fecal coliform plate counts. A total of 21 brands of commercial bottled water, consisting of 10 imported and 11 in-house brands, selected at random from 96 brands that are consumed in Puerto Rico, were tested at three different time intervals. The Standard Limulus Amebocyte Lysate test, gel clot method, was used to measure the endotoxin concentrations. The minimum endotoxin concentration in 63 water samples was less than 0.0625 EU/mL, while the maximum was 32 EU/mL. The minimum bacterial count showed no growth, while the maximum was 7,500 CFU/mL. Bacterial isolates like P. fluorescens, Corynebacterium sp. J-K, S. paucimobilis, P. versicularis, A. baumannii, P. chlororaphis, F. indologenes, A. faecalis and P. cepacia were identified. Repeated measures analysis of variance demonstrated that endotoxin concentration did not change over time, while there was a statistically significant (p bacterial count over time. In addition, multiple linear regression analysis demonstrated that a unit change in the concentration of endotoxin across time was associated with a significant (p bacterial growth was not detected in some water samples, endotoxin was present. Measurement of Gram-negative bacterial endotoxins is one of the methods that have been suggested as a rapid way of determining bacteriological water quality.

MINERAL WATERS IN RHEUMATOID ARTHRITIS

Directory of Open Access Journals (Sweden)

BORGES, TIAGO

2013-02-01

Full Text Available Background: Rheumatoid arthritis (RA is an autoimmune disorder affecting nearly 1% of adult population. First-line therapies include disease-modifying antirheumatic drugs, but creno-balneotherapyis often prescribed in rheumatic disorders and RA is no exception. Objectives: To know the efficacy of creno-balneotherapy in RA. Methods: A Medline based search was made using MeSH terms “balneology” and “rheumatoid arthritis”. Articles concerning the use of mineral waters in RA treatment were included. Results: In RA, two traditional ways of employing mineral waters are commonly used: immersion and peliotherapy. Each owns their benefits to non-specific or hydrotherapeutic effects and specific or crenotherapeutic effects. Mineral waters must be regarded as an adjuvant therapy in quiescent, stable or non-progressive RA. Significant benefits have been accomplished with radonenriched and sulphurous waters. Isothermal or hyperthermal waters should be preferred. Conclusions: Although there is a global lack of evidence, mineral waters are a safe and effective therapy to be considered in RA.

A margin of exposure approach to assessment of non-cancerous risk of diethyl phthalate based on human exposure from bottled water consumption.

Science.gov (United States)

Zare Jeddi, Maryam; Rastkari, Noushin; Ahmadkhaniha, Reza; Yunesian, Masud; Nabizadeh, Ramin; Daryabeygi, Reza

2015-12-01

Phthalates may be present in food due to their widespread presence as environmental contaminants or due to migration from food contact materials. Exposure to phthalates is considered to be potentially harmful to human health as well. Therefore, determining the main source of exposure is an important issue. So, the purpose of this study was (1) to measure the release of diethyl phthalate (DEP) in bottled water consumed in common storage conditions specially low temperature and freezing conditions; (2) to evaluate the intake of DEP from polyethylene terephthalate (PET) bottled water and health risk assessment; and (3) to assess the contribution of the bottled water to the DEP intake against the tolerable daily intake (TDI) values. DEP migration was investigated in six brands of PET-bottled water under different storage conditions room temperature, refrigerator temperature, freezing conditions (40 °C ,0 °C and -18 °C) and outdoor] at various time intervals by magnetic solid extraction (MSPE) using gas chromatography-mass spectroscopy (GC-MS). Eventually, a health risk assessment was conducted and the margin of exposure (MOE) was calculated. The results indicate that contact time with packaging and storage temperatures caused DEP to be released into water from PET bottles. But, when comprising the DEP concentration with initial level, the results demonstrated that the release of phthalates were not substantial in all storage conditions especially at low temperatures ( children > lactating women > teenagers > adults > pregnant women), but in all target groups, the MOE was much higher than 1000, thus, low risk is implied. Consequently, PET-bottled water is not a major source of human exposure to DEP and from this perspective is safe for consumption.

Bottle roll leach test for Temrezli uranium ore

International Nuclear Information System (INIS)

Çetin, K.; Bayrak, M.; Turan, A. İsbir; Üçgül, E.

2014-01-01

The bottle roll leach test is one of the dynamic leaching procedure which can meet in-situ mining needs for determining suitable working conditions and helps to simulate one of the important parameter; injection well design. In this test, the most important parameters are pulp density, acidic or basic concentration of leach solution, time and temperature. In recent years, bottle roll test is used not only for uranium but also gold, silver, copper and nickel metals where in situ leach (ISL) mining is going to be applied. For this purpose for gold and silver metal cyanide bottle roll tests and for uranium metal; acidic and basic bottle roll tests could be applied. The new leach test procedure which is held in General Directorate of Mineral Research and Exploration (MTA) of Turkey is mostly suitable for determining metal extraction conditions and recovery values in uranium containing ore bodies. The tests were conducted with samples taken from Temrezli Uranium Ore located in approximately 200 km east of Turkey’s capital, Ankara. Mining rights of Temrezli Ore is controlled 100% by Anatolia Energy Ltd. The resource estimate includes an indicated mineral resource of 10.827 Mlbs U_3O_8 [~4160 t U] at an average grade of 1426 ppm [~1210 ppm U] and an additional inferred resource of 6.587 Mlbs of U_3O_8 [~2530 t U] at an average grade of 904 ppm [~767 ppm U]. In accordance with the demand from Anatolia Energy bottle roll leach tests have been initiated in MTA laboratories to investigate the recovery values of low-grade uranium ore under in-situ leach conditions. Bottle roll leaching tests are performed on pulverized samples with representative lixiviant solution at ambient pressure and provide an initial evaluation of ore leachability with a rough estimate of recovery value. At the end of the tests by using 2 g/L NaHCO_3 and 0.2 g/L H_2O_2 more than 90% of uranium can pass into leach solution in 12 days. (author)

Identification of Bottled Zam Zam Water in Malaysian Market using Hydrogen and Oxygen Stable Isotobe Ratios (δ2H and δ18O)

International Nuclear Information System (INIS)

Roslanzairi Mostapa; Abdul Kadir Ishak; Kamaruzaman Mohamad; Rohaimah Demanah

2014-01-01

The water drawn from the well of Zam Zam is believed by the adherents of Islam to be blessed and capable of treating a variety of ailments. The water originates from a well in an alluvium area, located in Mecca, Saudi Arabia and has been in use since 4000 years ago. Due to the religious significance of the water drawn from this well, bottled versions are very popular among Malaysians. Unfortunately, this disproportionate popularity may entice some unscrupulous dealers to engage in fraudulent behaviour, such as selling ordinary water purported to be Zam Zam water. This unethical practice might very well pose a physical and economical hazard to consumers. Therefore, for the purpose of this preliminary study, five samples of Zam Zam bottled water from different brands were purchased and analyzed using Isotope Ratio Mass Spectrometer (IRMS). For comparison purpose, four samples of zam zam water from Mecca, and two more types of water samples originating from Malaysian were also analyzed, namely, bottled drinking water and tap water. The sources of these water samples are from groundwater and surface water (river), respectively. Results of hydrogen (ε 2 H) and oxygen (ε 18 O) isotope ratios of zam zam water from mecca are in the range of -13.62 % to -10.60 %, and -2.17 % to 0.06 %, respectively, while the hydrogen (ε 2 H) and oxygen (δ 18 O) isotope ratios of five samples from the bottled Zam Zam water are within the range of -50.74 % to -7.95 % to -5.39 %, respectively. The results from the measured values of all the water samples, and might be immensely useful for the purpose of regulatory monitoring of bottled water products. (author)

Determination of Perchlorate in Bottled Water from Italy

Directory of Open Access Journals (Sweden)

Patrizia Iannece

2013-06-01

Full Text Available Perchlorate is regarded as an emerging persistent inorganic contaminant. It is widely known that perchlorate is an endocrine disruptor as it competitively inhibits iodide transport in the thyroid gland. As drinking water is the major source of human exposure to perchlorate, its occurrence in commercially available bottled waters purchased in different regions of Italy was investigated. Perchlorate was measured using the rapid, sensitive, and selective LC-ESI-MS/MS (liquid chromatography-electrospray tandem mass spectrometry method by multiple reaction monitoring (MRM of the transition 98.8→82.8, which corresponds to the loss of one oxygen atom in the perchlorate ion (ClO4−→ClO3−. The chlorine isotope ratio (35Cl/37Cl was used as a confirmation tool. The limit of quantification (LOQ for this method was 5 ng/L, and the recovery ranged from 94% to 108%. Perchlorate was detected in 44 of the 62 drinking waters tested, with concentrations ranging from <5 to 75 ng/L. These values are similar in magnitude to those reported in drinking water from the USA and do not pose an immediate health concern.

Marketing mix of chosen Slovak mineral water

Directory of Open Access Journals (Sweden)

Juhanová Silvia

2001-09-01

Full Text Available Considering its small area, Slovakia abounds in many sources of mineral waters and a considerable amount of them can be used for the commercial utilization. STN 86 8000 divides mineral waters in the natural mineral waters, natural mineral table waters and the natural mineral healing waters. Natural mineral water is, after the present norm, in effect water, which rises from natural trapped sources. This type of water contains more than 1 gram of dissolved substances or 1 gram of dissolved CO 2 in 1 litter. Natural mineral table water is water that, with its chemical composition as well as its physical and sensorial attributes is suitable as a refresher. It contains at least 1 gram of melted CO2 and up to 6 grams of dissolved illiquid substances in 1 litter. The mentioned substances are not characterised by any marked pharmacological effect. Natural mineral healing water is water, which with an eye to its chemical composition and physical properties, have a scientifically demonstrable effects to the human health and it is generally used for healing purposes. In the present contribution, an attention is orientated to the occurrence of listed types of waters in Slovakia, in connection with geological conditions of their circulation and accumulation and especially with possibilities of their use on the Slovak buyer’s market.The marketing mix is a complex of information, which can be regulated. Firms accumulate this information to satisfy a customer. Marketing mix of mineral waters includes information about four variables: product (characteristics of product, quality, packing, design..., prices, advertisement, distribution (the way how to get product to customer. Data listed in the contribution come from the sectional market research, which was performed between December 1st and December 22nd 2000 in twenty groceries in

Towards lower carbon footprint patterns of consumption: The case of drinking water in Italy

International Nuclear Information System (INIS)

Botto, S.; Niccolucci, V.; Rugani, B.; Nicolardi, V.; Bastianoni, S.; Gaggi, C.

2011-01-01

The effects that individual consumption behaviours have on climate change are explored, focusing on products that satisfy the same need but with different carbon footprints. Two types of drinking water, produced, distributed and consumed in Italy, were compared as a case study: tap water and PET-bottled natural mineral water. The first is the one supplied to the municipality of Siena, while the second is a set of 6 different Italian bottled water brands. The results showed that drinking 1.5 L of tap water instead of PET-bottled water saves 0.34 kg CO 2 eq. Thus, a PET-bottled water consumer (2 L per day) who changes to tap water may prevent 163.50 kg CO 2 eq of greenhouse gas emissions per year. In monetary terms, this translates into a tradable annual verified emission reduction (VER) between US$ 0.20 and 7.67 per drinker. Analysing a mature bottled water market, such as the Italian one, may provide insights into the growing global bottled-water market and its effects on climate change. The environmental and economic benefits of changing drinking water habits are also discussed.

Comparison of solidification of floating drop and homogenous liquid-liquid microextractions for the extraction of two plasticizers from the water kept in PET-bottles.

Science.gov (United States)

Yamini, Yadollah; Ghambarian, Mahnaz; Khalili-Zanjani, Mohammad Reza; Faraji, Mohammad; Shariati, Shahab

2009-09-01

Two approaches based on solidification of floating drop microextraction (SFDME) and homogenous liquid-liquid microextraction (HLLE) were compared for the extraction and preconcentration of di-(2-ethylhexyl) phthalate (DEHP) and di-(2-ethylhexyl) adipate (DEHA) from the mineral water samples. In SFDME, a floated drop of the mixture of acetophenone/1-undecanol (1:8) was exposed on the surface of the aqueous solution and extraction was permitted to occur. In HLLE, a homogenous ternary solvent system was used by water/methanol/chloroform and the phase separation phenomenon occurred by salt addition. Under the optimal conditions, the LODs for the two target plasticizers (DEHA and DEHP), obtained by SFDME-GC-FID and HLLE-GC-FID, were ranged from 0.03 to 0.01 microg/L and 0.02 to 0.01 microg/L, respectively. HLLE provided higher preconcentration factors (472.5- and 551.2-fold) within the shorter extraction time as well as better RSDs (4.5-6.9%). While, in SFDME, high preconcentration factors in the range of 162-198 and good RSDs in the range of 5.2-9.6% were obtained. Both methods were applied for the analysis of two plasticizers in different water samples and two target plasticizers were found in the bottled mineral water after the expiring time and the boiling water was exposed to a polyethylene vial.

Impact of temperature and storage duration on the chemical and odor quality of military packaged water in polyethylene terephthalate bottles

International Nuclear Information System (INIS)

Greifenstein, Michael; White, Duvel W.; Stubner, Alex; Hout, Joseph; Whelton, Andrew J.

2013-01-01

The impact of temperature and storage time on military packaged water (MPW) quality was examined at four temperatures (23.0 °C to 60.0 °C) for 120 days. Polyethylene terephthalate (PET) bottles were filled in California and Afghanistan with unbuffered water treated by reverse osmosis. The US military's water pH long-term potability standard was exceeded, and US Food and Drug Administration (USFDA) and US Environmental Protection Agency (USEPA) drinking water pH and odor intensity limits were also exceeded. During a 70 day exposure period, Port Hueneme MPW total organic carbon and total trihalomethane levels increased from 37.7 °C, consume bottled water within 14 days of packaging

Long-lived natural Ra isotopes in mineral, therapeutic and spring waters in Caxambu, Minas Gerais state, Brazil

International Nuclear Information System (INIS)

Negrao, Sergio Garcia; Oliveira, Joselene de

2011-01-01

In many countries all around the world, there is an increasing tendency to replace surface drinking water by commercially available bottled mineral water from different springs for consumption purposes. These practices involve an increased risk of finding higher activities of natural radionuclides in such waters, predominantly of the uranium-radium decay series. Naturally occurring radionuclides such as 238 U, 226 Ra, 222 Rn, 210 Po and 228 Ra are found frequently dissolved in water supplies and their concentrations vary over an extremely wide range. However, from the point of view of radiation hygiene, results of many worldwide surveys indicate that only 222 Rn, 226 Ra and 228 Ra have been found in concentrations that may be of health concern. 226 Ra and 228 Ra are the most radiotoxic isotopes of radium due to their long half-lives, 1,600 and 5.75 years, respectively. Since their chemical behavior is similar to that of calcium, radium isotopes tend to accumulate mostly in the skeleton after ingestion. For the purposes of this study, samples of mineral spring water were taken in Caxambu, a thermal resort located in the extreme south of Minas Gerais, 370 km south of Belo Horizonte. Caxambu is renowned by its waterpark, which has twelve sources of mineral water already being used in treatment of stomach, liver and kidney diseases, between others. 226 Ra activity concentrations varied from 83 to 3,599 mBq L-1, the highest value determined at Venancio spring. Activity concentrations of 228 Ra ranged from 69 to 4,481 mBq L-1. 228 Ra/ 226 Ra activity ratios varied from 0.079 to 4.2. (author)

Recycling plastic bottles in a creative way

OpenAIRE

Pavlin, Suzana

2016-01-01

Beside other plastic products, plastic bottles represent a true environmental disaster in the last few years. We assume that hardly anyone asks what happens after they drink that last drop of water out of it. Just like most municipal waste, a plastic bottle can be reused, recycled, burned or deposited into landfill. When the Environment Protection Act is not respected, plastic bottle ends up in the nature, very often in the sea, where it decomposes very slowly and has negative influence on th...

Green Fiber Bottle

DEFF Research Database (Denmark)

Didone, Mattia; Tosello, Guido

has to have an inner coating barrier. The most reliable solution proposed is to coat the inner walls with silicon dioxide, which is not biodegradable but rather environmentally inert. To enhance the environmental footprint and sustainability of the bottle, and to be competitive with the existing...... technologies, the manufacturing technology for the production of the bottle has to offer the possibility of significant energy savings. Molded pulp products are made from wood fibers dispersed in water, and then they are formed, drained and dried. A relatively large quantity of resources (i.e. energy and time......) is consumed during the drying process. It is in this process stage that an innovative way of drying the products can be exploited by using the concept of impulse drying. Impulse drying is an advance drying technique in which water is removed from a wet paper pulp by the combination of mechanical pressure...

MINERAL WATER FROM SUPERMARKET VS. TAP WATER. SOME CONSIDERATIONS RELATED TO INNOCUITY

Directory of Open Access Journals (Sweden)

Ciprian – Nicolae POPA

2015-04-01

Full Text Available 15 Romanian brands of mineral water were purchased from hypermarket. For each of the 15 mineral waters were determined the content of nitrates, nitrites and pH. The data obtained were compared with the content of nitrates, nitrites and pH of the tap water collected in 15 locations in Bucharest, according to data released by the Apa Nova operator. The results showed that the mean of tap water pH in Bucharest, although slightly higher than the tested mineral waters pH, did not differ significantly from the mean of mineral waters pH, being situated in the alkaline domain. The mean content of nitrates in tap water in Bucharest, did not differ significantly from that of the tested mineral waters (t = 0.811. Nitrates content of tap water in Bucharest was significantly distinct less, as the pH was higher (r = 0.68**. Basically, the change in pH by one unit, lowers the amount of nitrate by 46%. Bucharest tap water nitrites content was significantly lower than that of tested mineral waters (0.005 mg/l to 0.0124; t = 2.674*. Basically, Bucharest tap water contained up to 2.5 times less nitrites than the nitrites mean of tested mineral waters.

Bacteriological Quality and Essential Elements in Bottled Water in ...

African Journals Online (AJOL)

Objective: The bacteriological examination of different commercially packaged water in Nsukka Metropolis was examined. The level of essential mineral elements and organic acids in the water were also evaluated to determine their conformity with the standards. Materials and Methods: Eleven (11) water samples (S1 ...

Environmental impact of an Italian wine bottle: Carbon and water footprint assessment.

Science.gov (United States)

Bonamente, Emanuele; Scrucca, Flavio; Rinaldi, Sara; Merico, Maria Cleofe; Asdrubali, Francesco; Lamastra, Lucrezia

2016-08-01

The food sector represents one of the major impacting sectors from an environmental point of view and, among all the products, wine emerges as one of the most studied by the literature. Single-issue approaches are commonly used, but a more comprehensive analysis is desirable, since a single indicator does not properly track the pressure on the environment. This paper presents a combined carbon and water footprint assessment, with a cradle to grave approach, for a protected designation of origin Italian red wine, and suggests a correlation among the two indicators across the life cycle phases. A total CF equal to 1.07±0.09kgCO2eq/bottle and a total WF equal to 580±30l/bottle were calculated for the studied product and a direct proportionality was found between the total CF and the sum of WFgrey(indirect) and WFblue. Copyright © 2016 Elsevier B.V. All rights reserved.

Nutritional value OF Bottle Gourd ( Lagenaria siceraria ) Seeds ...

African Journals Online (AJOL)

Whole seeds, dehulled seeds and seed coats of bottle gourd seed (Lagenaria siceraria) were analysed for their proximate, amino acids and mineral compositions. The results of the analysis showed that, whole seed has highest content of moisture (17.5 0.21%) and ash (5.80 0.83%) while dehulled had highest amount ...

Correlation of lithium levels between drinking water obtained from different sources and scalp hair samples of adult male subjects.

Science.gov (United States)

Baloch, Shahnawaz; Kazi, Tasneem Gul; Afridi, Hassan Imran; Baig, Jameel Ahmed; Talpur, Farah Naz; Arain, Muhammad Balal

2017-10-01

There is some evidence that natural levels of lithium (Li) in drinking water may have a protective effect on neurological health. In present study, we evaluate the Li levels in drinking water of different origin and bottled mineral water. To evaluate the association between lithium levels in drinking water with human health, the scalp hair samples of male subjects (25-45 years) consumed drinking water obtained from ground water (GW), municipal treated water (MTW) and bottled mineral water (BMW) from rural and urban areas of Sindh, Pakistan were selected. The water samples were pre-concentrated five to tenfold at 60 °C using temperature-controlled electric hot plate. While scalp hair samples were oxidized by acid in a microwave oven, prior to determined by flame atomic absorption spectrometry. The Li content in different types of drinking water, GW, MTW and BMW was found in the range of 5.12-22.6, 4.2-16.7 and 0.0-16.3 µg/L, respectively. It was observed that Li concentration in the scalp hair samples of adult males consuming ground water was found to be higher, ranged as 292-393 μg/kg, than those who are drinking municipal treated and bottle mineral water (212-268 and 145-208 μg/kg), respectively.

Risk assessment from intake of Naturally Occuring Radioactive Materials in some bottled drinking water on the Ghanaian market

International Nuclear Information System (INIS)

Portuphy, M. O.

2015-07-01

Activity concentrations of the Naturally Occurring Radioactive Materials (NORMs) in some bottled water brands were analyzed using gamma spectrometry. 40 K activity concentrations were in the range of 3.57-5.47Bq/L, the highest occurring in brand L9. Similarly 232 Th activity concentrations were in the range of 0.30-0.56 Bq/L with the highest occurring in brand L8. 226 Ra was identified in eleven brands with the remaining five below detection limit. The highest value (0.53Bq/L) occurred in brand L9. Comparison of the mean concentrations showed significant differences at (α=0.05) between the various brands of bottled water. Estimated committed effective doses were generally below 0.1mSv/a for all age groups with the exception of children <1yr. Estimated lifetime cancer and hereditary risk was done using the ICRP risk assessment methodology. Relationship between Activity concentrations and some physicochemical parameters were established using scatter graphs. The significant one was the conductivity parameter and how estimated activity concentrations tend to correlate (Jobbàgy et al, 2013). Trace elements and heavy metals were analysed using titrimetry, UV-VIS spectroscopy and atomic absorption spectroscopy. Their levels were below recommended and conventional levels. Conclusively bottled water brands analyzed were therefore radiologically safe. (au)

Radon and radium concentrations in bottled waters: An estimate of ingestion doses

International Nuclear Information System (INIS)

Duenas, C.; Fernandez, M.C.; Carretero, J.; Liger, E.

1997-01-01

Concentration levels of Ra-226 and Rn-222 have been analysed in most of the bottled waters commercially available in Spain. Concentrations up to about 600 Bq/m 3 with a geometric mean of 12 Bq/m 3 were observed for Ra-226. For Rn-222 a geometric mean of 1200 Bq/m 3 with values ranging from 52000 to 1400 Bq/m 3 were measured. Doses resulting from the consumption of these waters were calculated. The effective dose equivalents due to the intake of Ra-226 present in these waters are expected to range from about 102 to 2 μSv·y -1 . Dose equivalents to the stomach due to Rn-222 intake through water consumption are estimated to reach values around 30 μSv·y -1 . (author)

Modeling CO2-Water-Mineral Wettability and Mineralization for Carbon Geosequestration.

Science.gov (United States)

Liang, Yunfeng; Tsuji, Shinya; Jia, Jihui; Tsuji, Takeshi; Matsuoka, Toshifumi

2017-07-18

Carbon dioxide (CO 2 ) capture and storage (CCS) is an important climate change mitigation option along with improved energy efficiency, renewable energy, and nuclear energy. CO 2 geosequestration, that is, to store CO 2 under the subsurface of Earth, is feasible because the world's sedimentary basins have high capacity and are often located in the same region of the world as emission sources. How CO 2 interacts with the connate water and minerals is the focus of this Account. There are four trapping mechanisms that keep CO 2 in the pores of subsurface rocks: (1) structural trapping, (2) residual trapping, (3) dissolution trapping, and (4) mineral trapping. The first two are dominated by capillary action, where wettability controls CO 2 and water two-phase flow in porous media. We review state-of-the-art studies on CO 2 /water/mineral wettability, which was found to depend on pressure and temperature conditions, salt concentration in aqueous solutions, mineral surface chemistry, and geometry. We then review some recent advances in mineral trapping. First, we show that it is possible to reproduce the CO 2 /water/mineral wettability at a wide range of pressures using molecular dynamics (MD) simulations. As the pressure increases, CO 2 gas transforms into a supercritical fluid or liquid at ∼7.4 MPa depending on the environmental temperature. This transition leads to a substantial decrease of the interfacial tension between CO 2 and reservoir brine (or pure water). However, the wettability of CO 2 /water/rock systems depends on the type of rock surface. Recently, we investigated the contact angle of CO 2 /water/silica systems with two different silica surfaces using MD simulations. We found that contact angle increased with pressure for the hydrophobic (siloxane) surface while it was almost constant for the hydrophilic (silanol) surface, in excellent agreement with experimental observations. Furthermore, we found that the CO 2 thin films at the CO 2 -hydrophilic

Assessment of 226Ra, 228Ra and 40K contents in the Egyptian bottled natural water

International Nuclear Information System (INIS)

El-Afifi, E.M.; Hilal, M.A.; Khalifa, S.M.; Aly, H.F.

2004-01-01

The activity concentrations of 2 26Ra, 2 28Ra and 4 0 and k in different brands of the bottled egyptian natural water of different origins obtained from four regions, have been analyzed nondestructively by gamma- ray spectrometry. The study covers nine brands of natural water commonly used mainly for drinking in egypt. The results showed, concentrations up to 184, 156 and 1700 mBq I - 1 for 2 26Ra, 2 28Ra and 4 0K, respectively, in one brand of the natural water from water from Siwa oasis. Whereas, lower activity concentrations of 2 26Ra and 2 28Ra were found in one brand of these natural waters from El sadat region. The activity concentration of 4 0K was found to be in the background range in the brands from El sadat, kafr El arbein and beilbeis regions. The committed effective doses reached 1.9 x 10 - 2 m Sy Y - 1 for ingestion of 2 26Ra and 2 28Ra for one liter per day, respectively, which are lower than the standard permissible limit by the WHO and IAEA. However, it is recommended to moderate drinking of bottled natural water to avoid the accumulation effect of radioactive nuclides especially radium

Liquid chromatographic determination of the cyanobacterial toxin beta-n-methylamino-L-alanine in algae food supplements, freshwater fish, and bottled water.

Science.gov (United States)

Scott, Peter M; Niedzwiadek, Barbara; Rawn, Dorothea F K; Lau, Ben P-Y

2009-08-01

Beta-N-Methylamino-L-alanine (BMAA) is a neurotoxin originally found in cycad seeds and now known to be produced by many species of freshwater and marine cyanobacteria. We developed a method for its determination in blue-green algae (BGA) food supplements, freshwater fish, and bottled water by using a strong cation-exchange, solid-phase extraction column for cleanup after 0.3 M trichloroacetic acid extraction of BGA supplements and fish. Bottled water was applied directly onto the solid-phase extraction column. For analysis of carbonated water, sonication and pH adjustment to 1.5 were needed. To determine protein-bound BMAA, the protein pellet left after extraction of the BGA supplement and fish was hydrolyzed by boiling with 6 M hydrochloric acid; BMAA was cleaned up on a C18 column and a strong cation-exchange, solid-phase extraction column. Determination of BMAA was by liquid chromatography of the fluorescent derivative formed with 9-fluorenylmethyl chloroformate. The method was validated by recovery experiments using spiking levels of 1.0 to 10 microg/g for BGA supplements, 0.5 to 5.0 microg/g for fish, and 0.002 microg/g for bottled water; mean recoveries were in the range of 67 to 89% for BGA supplements and fish, and 59 to 92% for bottled water. Recoveries of BMAA from spiked extracts of hydrolyzed protein from BGA supplements and fish ranged from 66 to 83%. The cleanup developed provides a useful method for surveying foods and supplements for BMAA and protein-bound BMAA.

Study of the influence of storage conditions on the quality and migration levels of antimony in polyethylene terephthalate-bottled water.

Science.gov (United States)

Payán, Luis; Poyatos, M Teresa; Muñoz, Lucía; La Rubia, M Dolores; Pacheco, Rafael; Ramos, Natividad

2017-06-01

The main objectives of this study are to determine the presence of antimony in water stored in polyethylene terephthalate bottles and the influence of temperature and time over the migration levels. For this purpose, Sb determination was carried out in water at different experimental conditions: storage for one to three weeks at 25 to 80 ℃; long-term (six months) storage at room temperature between 16 and 24 ℃ and storage in car during summer which is a common consumer's habit. In addition, water quality analysis was developed after different time-temperature storage conditions. All the samples at the end of their storage conditions were analyzed by inductively coupled plasma mass spectrometry. The limit of detection and quantification were 0.50 and 0.80 µg/L, respectively. The results for the bottled water stored during six months indicated that the average Sb concentration was 0.332 ± 0.015 µg/L. This value is below the European maximum permissible migration level of 5 µg/L. With regard to the newly bottled water, no Sb was detected at the initial time for all temperatures studied. However, the Sb concentration in water increased with both time and temperature. The levels of Sb started exceeding the European limits when the samples were stored at 60 ℃ for two weeks.

Evaluation of Minerals Content of Drinking Water in Malaysia

Science.gov (United States)

Azlan, Azrina; Khoo, Hock Eng; Idris, Mohd Aizat; Ismail, Amin; Razman, Muhammad Rizal

2012-01-01

The drinking and mineral water samples obtained from different geographical locations had concentrations of the selected minerals lower than the standard limits, except for manganese, arsenic, and fluoride. The concentrations of manganese and arsenic in two mineral water samples were slightly higher than the standard international recommended limits. One mineral water sample had a fluoride concentration higher than the standard limits, whereas manganese was not detected in nine drinking and mineral water samples. Most of the selected minerals found in the tap water samples were below the international standard limits, except for iron and manganese. The concentrations of iron and manganese in the tap water samples were higher than the standard limits, which were obtained from one and three of the studied locations, respectively. The potable water obtained from various manufacturers and locations in Peninsular Malaysia is safe for consumption, as the minerals concentrations were below the standard limits prescribed by the Malaysian Food Regulations of 1985. The data obtained may also provide important information related to daily intake of these minerals from drinking water. PMID:22649292

Evaluation of Minerals Content of Drinking Water in Malaysia

Directory of Open Access Journals (Sweden)

Azrina Azlan

2012-01-01

Full Text Available The drinking and mineral water samples obtained from different geographical locations had concentrations of the selected minerals lower than the standard limits, except for manganese, arsenic, and fluoride. The concentrations of manganese and arsenic in two mineral water samples were slightly higher than the standard international recommended limits. One mineral water sample had a fluoride concentration higher than the standard limits, whereas manganese was not detected in nine drinking and mineral water samples. Most of the selected minerals found in the tap water samples were below the international standard limits, except for iron and manganese. The concentrations of iron and manganese in the tap water samples were higher than the standard limits, which were obtained from one and three of the studied locations, respectively. The potable water obtained from various manufacturers and locations in Peninsular Malaysia is safe for consumption, as the minerals concentrations were below the standard limits prescribed by the Malaysian Food Regulations of 1985. The data obtained may also provide important information related to daily intake of these minerals from drinking water.

Evaluation of minerals content of drinking water in Malaysia.

Science.gov (United States)

Azlan, Azrina; Khoo, Hock Eng; Idris, Mohd Aizat; Ismail, Amin; Razman, Muhammad Rizal

2012-01-01

The drinking and mineral water samples obtained from different geographical locations had concentrations of the selected minerals lower than the standard limits, except for manganese, arsenic, and fluoride. The concentrations of manganese and arsenic in two mineral water samples were slightly higher than the standard international recommended limits. One mineral water sample had a fluoride concentration higher than the standard limits, whereas manganese was not detected in nine drinking and mineral water samples. Most of the selected minerals found in the tap water samples were below the international standard limits, except for iron and manganese. The concentrations of iron and manganese in the tap water samples were higher than the standard limits, which were obtained from one and three of the studied locations, respectively. The potable water obtained from various manufacturers and locations in Peninsular Malaysia is safe for consumption, as the minerals concentrations were below the standard limits prescribed by the Malaysian Food Regulations of 1985. The data obtained may also provide important information related to daily intake of these minerals from drinking water.

The optimation of radon-222 determination in water by Lucas cell technique

International Nuclear Information System (INIS)

Andrejkovicova, S.; Kuruc, J.; Kovacsova, A.; Mackova, J.; Rajec, P.

2003-01-01

The aim of this work was to determine detection efficiency ε, volume activity a v , low detection limit, minimal detection activity for radon. There were collecting several samples of water: water from tap water, mineral water, thermal water, water from wells and bottled drinking water. As we expected, the lowest values of volume activities of radon were reached in bottled drinking water (0.1 - 4.9 Bq/dm 3 ). Higher values were reached in water from tap water and natural mineral water (2.5 - 14.9 Bq/dm 3 ). The highest volume activities of radon were obtained in thermal water and water from wells (17.2 - 107.9 Bq/dm 3 ). Method for determination of radon in water was verified at Institute of Preventive and Clinical Medicine, Bratislava, Slovakia. Results of radon concentration in waters are in accordance with an uppermost - accepted value of radon in water. The volume activity of radon in our samples has never been higher as a limit value has allowed (300 Bq/dm 3 ). (authors)

Some physicochemical aspects of water-soluble mineral flotation.

Science.gov (United States)

Wu, Zhijian; Wang, Xuming; Liu, Haining; Zhang, Huifang; Miller, Jan D

2016-09-01

Some physicochemical aspects of water-soluble mineral flotation including hydration phenomena, associations and interactions between collectors, air bubbles, and water-soluble mineral particles are presented. Flotation carried out in saturated salt solutions, and a wide range of collector concentrations for effective flotation of different salts are two basic aspects of water-soluble mineral flotation. Hydration of salt ions, mineral particle surfaces, collector molecules or ions, and collector aggregates play an important role in water-soluble mineral flotation. The adsorption of collectors onto bubble surfaces is suggested to be the precondition for the association of mineral particles with bubbles. The association of collectors with water-soluble minerals is a complicated process, which may include the adsorption of collector molecules or ions onto such surfaces, and/or the attachment of collector precipitates or crystals onto the mineral surfaces. The interactions between the collectors and the minerals include electrostatic and hydrophobic interactions, hydrogen bonding, and specific interactions, with electrostatic and hydrophobic interactions being the common mechanisms. For the association of ionic collectors with minerals with an opposite charge, electrostatic and hydrophobic interactions could have a synergistic effect, with the hydrophobic interactions between the hydrophobic groups of the previously associated collectors and the hydrophobic groups of oncoming collectors being an important attractive force. Association between solid particles and air bubbles is the key to froth flotation, which is affected by hydrophobicity of the mineral particle surfaces, surface charges of mineral particles and bubbles, mineral particle size and shape, temperature, bubble size, etc. The use of a collector together with a frother and the use of mixed surfactants as collectors are suggested to improve flotation. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydrogeochemical tracing of mineral water in Jingyu County, Northeast China.

Science.gov (United States)

Yan, Baizhong; Xiao, Changlai; Liang, Xiujuan; Wu, Shili

2016-02-01

The east Jilin Province in China, Jingyu County has been explored as a potential for enriching mineral water. In order to assess the water quality and quantity, it is of crucial importance to investigate the origin of the mineral water and its flow paths. In this study, eighteen mineral springs were sampled in May and September of 2012, May and September of 2013, and May 2014 and the environment, evolvement, and reaction mechanism of mineral water formation were analysed by hydrochemical data analysis, geochemical modelling and multivariate statistical analysis. The results showed that the investigated mineral water was rich in calcium, magnesium, potassium, sodium, bicarbonate, chloride, sulphate, fluoride, nitrate, total iron, silicate, and strontium, and mineral water ages ranged from 11.0 to more than 61.0 years. The U-shape contours of the mineral ages indicate a local and discrete recharge. The mineral compositions of the rocks were olivine, potassium feldspar, pyroxene, albite, and anorthite and were under-saturated in the mineral water. The origin of mineral water was from the hydrolysis of basalt minerals under a neutral to slightly alkaline and CO2-rich environment.

Certified reference materials for the determination of mineral oil hydrocarbons in water, soil and waste

Energy Technology Data Exchange (ETDEWEB)

Koch, M.; Liebich, A.; Win, T.; Nehls, I.

2005-07-01

The international research project HYCREF, funded by the European Commission in the 5{sup th} Framework programme, aimed to develop methods to prepare homogeneous and stable water-, soil- and waste reference materials contaminated with mineral oil hydrocarbons and to test certify the mineral oil content by gas chromatographic methods. As mineral oil products are important sources for environmental contaminations a high need exists for certified reference materials for their determination using the new gas chromatographic methods (soil: ISO/FDIS 16703, waste: ENpr 14039, water: ISO 9377-2). The experimental conditions and results for preparation and characterisation of a total of nine reference materials (3 water, 3 soil- and 3 waste materials) are described and discussed. Target values for the reference materials were defined at the beginning of the project in order to have clear quality criteria, which could be compared with the achieved results at the end of the project. These target specifications were related to the maximum uncertainty from test certification exercises (<5% for soil/waste and <10% for water), the maximum inhomogeneity between bottles (<3%) and minimum requirements for stability (>5 years for soil/waste and >2 years for water). The feasibility studies showed that solid materials (soil, waste) could be prepared sufficiently homogeneous and stable. The test certified values of the 6 solid materials comprise a wide range of mineral oil content from about 200-9000 mg/kg with expanded uncertainties between 5.7-13.1% using a coverage factor k (k=2). The development of new water reference materials - the so-called ''spiking pills'' for an offshore- and a land-based discharge water represents one of the most innovative aspects of the project. The spiking pill technology facilitates the application and storage and improves the material stability compared with aqueous materials. Additional to the preparation and test certification of

Influence of packaging and conditions of storaging on content of mineral water Guber-Srebrenica

Directory of Open Access Journals (Sweden)

Blagojević Dragana D.

2008-01-01

Full Text Available Mineral waters are found in nature in greater depths most often in reduction conditions, so after surfacing their content alters in contact with oxygen, which is caused by oxidation of certain components. Due to this, efforts were made to make these waters more stabile so they could be used after certain time. This work monitors the stability of Guber (Argentaria-Srebrenica water exposed to light and with addition of ascorbic acid. The methods of analysis and the parameters analyzed are: gravimetric (SO2-4, suspended solids, total dry residue at 180°C, conductometry (electric conductivity, volumetric (Al3+, spectrometric (SiO2 and atomic-absorption spectrophotometry (Fe2+, Mg2+, Mn2+, Zn2+, K+, Ca2+, Na+ i Cu2+. Obtained results of water analysis, after retaining water in PET (polyethylentereftalate and glass bottles, in certain time intervals, show that significant changes of concentration of Fe2+, Al3+, K+, Ca2+, pH value and electric conductivity occurred. Concentration of iron Fe2+ has been slightly changed after 120 days, in sample stabilized with 0,2 g ascorbic acid, while concentrations of Al and K+ were changing the same as without adding of stabilizer. Samples of water in glass packaging without added stabilizer are less stable compared to samples which were retained in PET packaging.

Assessment of metal contaminations leaching out from recycling plastic bottles upon treatments.

Science.gov (United States)

Cheng, Xiaoliang; Shi, Honglan; Adams, Craig D; Ma, Yinfa

2010-08-01

Heavy metal contaminants in environment, especially in drinking water, are always of great concern due to their health impact. Due to the use of heavy metals as catalysts during plastic syntheses, particularly antimony, human exposure to metal release from plastic bottles has been a serious concern in recent years. The aim and scope of this study were to assess metal contaminations leaching out from a series of recycling plastic bottles upon treatments. In this study, leaching concentrations of 16 metal elements were determined in 21 different types of plastic bottles from five commercial brands, which were made of recycling materials ranging from no. 1 to no. 7. Several sets of experiments were conducted to study the factors that could potentially affect the metal elements leaching from plastic bottles, which include cooling with frozen water, heating with boiling water, microwave, incubating with low-pH water, outdoor sunlight irradiation, and in-car storage. Heating and microwave can lead to a noticeable increase of antimony leaching relative to the controls in bottle samples A to G, and some even reached to a higher level than the maximum contamination level (MCL) of the US Environmental Protection Agency (USEPA) regulations. Incubation with low-pH water, outdoor sunlight irradiation, and in-car storage had no significant effect on antimony leaching relative to controls in bottle samples A to G, and the levels of antimony leaching detected were below 6 ppb which is the MCL of USEPA regulations. Cooling had almost no effect on antimony leaching based on our results. For the other interested 15 metal elements (Al, V, Cr, Mn, Co, Ni, Cu, As, Se, Mo, Ag, Cd, Ba, Tl, Pb), no significant leaching was detected or the level was far below the MCL of USEPA regulations in all bottle samples in this study. In addition, washing procedure did contribute to the antimony leaching concentration for polyethylene terephthalate (PET) bottles. The difference of antimony leaching

levels of common ions in bottled mineral waters consumed in addis

African Journals Online (AJOL)

Preferred Customer

ment, cancer, organ damage, nervous system damage, and in ... consumed in any desired amount without adverse effect on ... drinking water which practically costs much .... mg/L) in 100 mL volumetric flask and working .... water and the lowest was in tap water sample. The ... blood pressure and a long list of degenerative.

Trace element analysis of mineral and tap water samples using total reflection x-ray fluorescence (TXRF)

International Nuclear Information System (INIS)

Mangala, M.J.; Korir, K.A.; Maina, D.M.; Kinyua, A.M.

2000-01-01

Results of trace element analysis by TXRF of tap water and various brands of bottled mineral water samples which are representative of local and imported brands sold in Nairobi are reported. The variation in elemental concentrations in water samples analyzed were as follows: potassium (K) 0.2 to 28.9 μg/ml; calcium (Ca) 2.2 to 120 μg/ml; titanium (Ti) 11 to 60 μg/l; manganese (Mn) 8 to 670 μg/l; iron (Fe) 31 to 540 μg/l; copper (Cu) 8 to 30 μg/l; zinc (Zn) 8 to 4730 μg/l; bromine (Br) 9 to 248 μg/l; rubidium (Rb) 10 to 40 μg/l and strontium (Sr) 10 to 1000 μg/l. Local mineral water samples contain higher levels of trace elements; manganese (Mn), zinc (Zn), bromine (Br), rubidium (Rb) and strontium (Sr) as compared to the imported brands. Principal component analysis of the results revealed three component loading factors clusters for: rubidium (Rb), strontium (Sr) and calcium (Ca); titanium (Ti), iron (Fe), bromine (Br), and zinc (Zn); zinc (Zn), manganese (Mn) and potassium (K) respectively. The percentage of total variance explained by the components was 31.4, 27.3, and 14.8 respectively. In this study, we also found that a limited spread of 5-6 mm for a 10 μl sample was achieved when the quartz sample carrier was dried in a low pressure (300 mbar) oven at 70 o C for 10 hours. (author)

An Investigation into the Effects of Temperature and Storage Time on Military Packaged Water in Afghanistan - The Liberation and Migration of Potential Contaminants from Expeditionary Water Packaging System Polyethylene Terephthalate Water Bottles

Science.gov (United States)

2012-03-29

soil ,  with  inhalation  being  the  predominant  route  of  entry  into  the   body.    Drinking  water...DEHP   concentrations   vanish   when   bottles   were   placed   outdoors   in   direct   sunlight   and   at   higher...Recycling  Plastic  Bottles  upon  Treatments."  Environmental  Science   Pollution  Research  17:  

Sulphurous Mineral Waters: New Applications for Health

Directory of Open Access Journals (Sweden)

Jose Manuel Carbajo

2017-01-01

Full Text Available Sulphurous mineral waters have been traditionally used in medical hydrology as treatment for skin, respiratory, and musculoskeletal disorders. However, driven by recent intense research efforts, topical treatments are starting to show benefits for pulmonary hypertension, arterial hypertension, atherosclerosis, ischemia-reperfusion injury, heart failure, peptic ulcer, and acute and chronic inflammatory diseases. The beneficial effects of sulphurous mineral waters, sulphurous mud, or peloids made from sulphurous mineral water have been attributed to the presence of sulphur mainly in the form of hydrogen sulphide. This form is largely available in conditions of low pH when oxygen concentrations are also low. In the organism, small amounts of hydrogen sulphide are produced by some cells where they have numerous biological signalling functions. While high levels of hydrogen sulphide are extremely toxic, enzymes in the body are capable of detoxifying it by oxidation to harmless sulphate. Hence, low levels of hydrogen sulphide may be tolerated indefinitely. In this paper, we review the chemistry and actions of hydrogen sulphide in sulphurous mineral waters and its natural role in body physiology. This is followed by an update of available data on the impacts of exogenous hydrogen sulphide on the skin and internal cells and organs including new therapeutic possibilities of sulphurous mineral waters and their peloids.

Hydrocarbons derived from petroleum in bottled drinking water from Mexico City.

Science.gov (United States)

Vega, Salvador; Gutiérrez, Rey; Ortiz, Rutilio; Schettino, Beatriz; Ramírez, Maria de Lourdes; Pérez, José Jesus

2011-06-01

This paper describes the concentrations of polycyclic aromatic hydrocarbons (PAHs) and aliphatic hydrocarbons (AHs) derived from petroleum in bottled drinking water samples that were collected over 1 year from Mexico City in two bottle sizes (1.5 and 19 L), all brought in supermarkets. The analysis was by gas chromatography with flame ionization detection. -Concentrations of AHs (9.26-1.74 μg/L) were greater than PAHs (20.15-12.78 ng/L). Individual concentrations of PAHs such as fluoranthene, benzo(b)fluoranthene, benzo(k)fluoranthene, indeno(1,2,3-cd)pyrene and benzo(ghi)perylene were comparable with data reported by the World Health Organization (WHO). Total concentrations of PAHs for all samples (BDW1: 12.78 μg/L, BDW2: 16.72 μg/L, BDW3: 14.62 μg/L, BDW4: 20.15 μg/L and BDW5: 13.23 ng/L) were below the maximum permissible European level of 100 ng/L; no regulations exist for AHs although their values were greater than PAHs (BDW1: 3.11 μg/L, BDW2: 8.45 μg/L, BDW3: 1.74 μg/L, BDW4: 4.75 μg/L and BDW5: 9.26 μg/L).

Determination of carbonyl compounds (acetaldehyde and formaldehyde in polyethylene terephthalate containers designated for water conservation

Directory of Open Access Journals (Sweden)

Redžepović Azra S.

2012-01-01

Full Text Available Polyethylene terephthalate (PET has in the last several years become the main packaging material for many food products, particularly carbonated beverages and bottled water, as well as for products of chemical industry (packaging of various hygiene maintenance agents, pesticides, solvents, etc.. The strength and permeability properties of PET are very good for packaging of beverages, its resistance to chemicals is high and it has a high degree of transparency. Acetaldehyde and formaldehyde are formed during the thermoforming of PET containers. After cooling, acetaldehyde and formaldehyde remain trapped in the walls of a PET bottle and may migrate into the water after filling and storage. Since there are no migration tests in Serbia prescribed for the determination of acetaldehyde and formaldehyde, the purpose of the paper is to test the quantitative contents of carbonyl compounds (acetaldehyde and formaldehyde in PET containers of different volumes, made by various manufacturers of bottled mineral carbonated and noncarbonated water, and exposed to different temperatures. In this study, the migration of acetaldehyde and formaldehyde from PET bottles into mineral carbonated and noncarbonated water was determined by high performance liquid chromatography. Taking into consideration that formaldehyde and acetaldehyde have no UV active or fluorescent group, the chromatography shall be preceded by derivatization in a closed system (due to a low boiling point of acetaldehyde and formaldehyde, which shall transform carbonyl compounds into UV active compounds.

Migration of 2-butoxyethyl acetate from polycarbonate infant feeding bottles

DEFF Research Database (Denmark)

Petersen, Jens Højslev; Lund, K.H.

2003-01-01

An enforcement campaign was carried out to assess the migration of 2-butoxyethyl acetate (2-BEA) from polycarbonate infant feeding bottles intended for repeated use. Migration was measured by three successive migration tests into two of the European Union official food simulants: distilled water......-BEA was found from eight of 12 bottles. However, migration above the target value of 0.33 mg kg(-1) was not observed in the third decisive test from any of the 12 different brands of polycarbonate feeding bottles. A migration of between 0.05 and 0.26 mg kg(-1) from seven of 12 bottles was measured...

Using of Mineral Recourses for Water Purification

International Nuclear Information System (INIS)

Tumanova, I.V.; Nazarenko, O.B.; Anna, Yu.

2009-01-01

Pollution of surface waters results in necessity of underground waters using for drinking. Underground waters are characterized by the high quantity of heavy metals salts. This led to development of methods reducing the concentration of the metal salts in water. Wide spread occurrence, cheapness and high sorption properties of nature minerals allow to consider them as perspective sorbents for different impurities extraction, including dissoluble compounds of heavy metals. Reachable purification efficiency with mineral resources use for the moment satisfies sanitary indexes and standards presenting to portable water in Russia. In given material there are presented the results of research of artificial sorbent and certain minerals sorption characteristics, which are typical for West Siberia. For purification quality improvement from Fe and Mn ions there are suggested to use the method of boiling bed.

Mineral waters from the Tanzawa Mountains

Energy Technology Data Exchange (ETDEWEB)

Oki, Y; Tajima, Y; Hirano, T; Ogino, K; Hirota, S; Takahashi, S; Kokaji, F; Moriya, M; Sugimoto, M

1964-11-01

Mineral waters from the depths of the Tanzawa mountains are briefly characterized as having high pH values ranging from 9.5 to 10.0. The origin of the mineral waters is discussed in relation to zeolites extensively developed along fractures and joints throughout the Tanzawa mountains. Thermal water (33/sup 0/C) of the Nakagawa spa may be regarded as evidence of past strong geothermal activity. Measurement of geothermal gradient at two locations, Nakagawa (12.6/sup 0/C/100m) and Higashi-sawa (5.55/sup 0/C/100m) also supports the presence of weak thermal activity in the depths. Chemical analysis of the mineral waters indicates that the pH of the system is chiefly controlled by the ratio of CO/sub 3//sup - -//HCO/sub 3//sup -/. The following reaction with zeolites promotes an increase of the pH: HCO/sub 3//sup -/ + (Ca/Na) zeolites reversible CO/sub 3//sup - -/ + H-type (Ca/Na) zeolites + (Ca/sup + +//Na/sup +/).

Determination of trace elements in bottled water in Greece by instrumental and radiochemical neutron activation analyses

International Nuclear Information System (INIS)

Soupioni, M.J.; Symeopoulos, B.D.; Papaefthymiou, H.V.

2006-01-01

Four different bottled water brands sold in Greece in the winter of 2001-2002 were analyzed for a wide range of chemical elements, using neutron activation analysis (NAA). The elements Na and Br were determined instrumentally (INAA), whereas the other metals and trace elements radiochemically (RNAA). The results indicated that the mean level of all the elements determined in the samples were well within the European Union (EU) directive on drinking water and accomplish the drinking water standards of the World Health Organisation (WHO) as well as of the Food and Drug Administration (FDA). (author)

factors influencing the consumption and standards of bottled

African Journals Online (AJOL)

BARTH EKWUEME

concern about the safety and quality of tap water in many cities and ... for the upper class markets. Most of the ... copying what is happening in the western world (Bullers,. 2002). ... bottled water and is the manufacturing of the water regulated?

Speciation of antimony in polyethylene terephthalate bottles

International Nuclear Information System (INIS)

Martin, R.R.; Ablett, J.; Shotyk, W.S.; Naftel, S.; Northrup, P.

2010-01-01

Antimony contamination has been reported in drinking water from polyethylene terephthalate (PET) bottles. Micro-X-ray fluorescence (XRF) analysis has been used to identify the distribution and chemical form of residual antimony used as a catalyst in the manufacture of PET bottles. The results are consistent with clusters of Sb(III) having dimensions of the order of tens of micrometers, clearly showing the ability of synchrotron radiation analyses to both map elemental distribution and determine oxidation state.

Application of Emotional Branding Strategy in the Model Development of Sports Brand of The Bottled Water Market

Directory of Open Access Journals (Sweden)

Marija Jankovic

2017-06-01

Full Text Available The new economy has brought new meaning to the brand, which is characterized by a brand, but also has a human touch, turning into an emotional brand. Alternative branding strategies put emphasis on brand experience in terms of emotional, holistic and socially responsible. Bottled water has become the world's "liquid gold" in the last 40 years, because it is a natural product, which is made with minimal costs. The paper develops the idea to perform a kind of humanization and the introduction of a new emotional brand of bottled water on the market, which will bear the name "Aqua F.I.F.A" designed label of FIFA international organizations, as well as the roof of the organizers of the most important football events in the world and the label of the national team. This paper will analyze in detail the market opportunities and prospects of introducing a unique sports brand, on the emotional aspect, with the use of effective marketing communication strategy.

120 MeV Ni Ion beam induced modifications in poly (ethylene terephthalate) used in commercial bottled water

International Nuclear Information System (INIS)

Kumar, Vijay; Sonkawade, R. G.; Ali, Yasir; Dhaliwal, A. S.

2012-01-01

We report the effects of heavy ion irradiation on the optical, structural, and chemical properties of polyethylene terephthalate (PET) film used in commercial bottled water. PET bottles were exposed with 120 MeV Ni ions at fluences varying from 3 x 10 10 to 3 x 10 12 ion/cm 2 . The modifications so induced were analyzed by using UV-Vis, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy. Substantial decrease in optical band gap is observed with the increase in ion fluence. In the FTIR spectra, most of bands are decreased due the degradation of the molecular structure. XRD measurements show the decrease in peak intensity, which reflects the loss of crystallinity after irradiation.

Thermo-mineral waters of Hammam Meskoutine (north-east Algeria: Composition and origin of mineralization

Directory of Open Access Journals (Sweden)

Benamara Abdelwaheb

2017-09-01

Full Text Available The extreme north-eastern Algeria, in particular the Guelma city conceals thermal springs, whose waters circulating at great depths allow the rain-waters to warm up (according to the average geothermal gradient of 1°C per 33 m and to acquire a mineralization which depends on the traversed rock. The goal of this research work was to determine mineralization origin of the thermo-mineral waters of Hammam Meskoutine (Algerian N-E. A hydro-chemical study involved analyses of a number of physical and chemical parameters of waters such as: temperature, hydrogen potential, electrolytical conductivity, Cl-, SO4 2-, HCO3 -, Ca2+, Mg2+, K+ and Na+. The data processing on the diagram revealed two dominating chemical facies: sulphate-magnesium and bicarbonate magnesium. With a high conductivity in excess of 2300 μS·cm-1, the temperature reaches 97°C. Calculation of the saturation index shows that the waters are supersaturated in carbonate minerals (calcite, dolomite and aragonite and less saturated with evaporite minerals (halite, anhydrite, sylvite and gypsum. The reconstitution in dissolved salts reveals a dominant salt rich in calcium bicarbonates, in calcium sulphates and secondarily in magnesium salts. Geological sections used in the study zone affirm that the chemical composition of the spring waters comes from the neritic limestone dissolution and the gypso-saline complex of Hammam Meskoutine.

Panel Board From Coconut Fibre And Pet Bottle

Science.gov (United States)

Ngadiman, Norhayati; Kaamin, Masiri; Abd. Kadir, Aslila; Sahat, Suhaila; Zaini, Aziza; Raihana Nor Zentan, Siti; Ain Ahmad, Nur; Amran, Wan Haizatul Aisyhah Wan

2018-03-01

The rate of global deforestation and its impact on the environment has led particle board manufacture to search for alternative feedstock, especially in countries where wood is less available compared to other cellulosic natural product. Based on the properties of coconut fibre and PET bottle, these two materials can be recycle as raw material for manufacture of panel board. As for this study, the coconut fibre were used as the filler and PET bottle as outer lining of the panel board. Two types of coconut fibre were used which are grinding and un-grinding coconut fibre. At first, the coconut fibre are undergoes softening, grinding, drying and sieving process, while PET bottle was cleaning, shredding, sieving before compacted using hydraulic hot press machine. There are four types of testing that been carried out which are swelling, water absorption, Modulus of Elasticity (MOE) and Modulus of Rupture (MOR). The result show the conventional board has the highest value for MOE test, so it's indicate that the conventional board is less strength from the coconut fibre board. As for water absorption test, the average water absorption of coconut fibre based panel board is less than conventional board. Overall, the coconut fibre board is better than conventional panel board because coconut fibre board are less swelling, has low water absorption, high modulus of rupture and low modulus of elasticity. Based on the finding, this coconut fibre panel board has potential as a stronger and long-lasting panel board than the conventional board in the market. Other than that, the panel also have their own aesthetic value since the recycled plastic bottle used as outer lining is colourful and giving aesthetic value.

An Intervention with Mineral Water Decreases Cardiometabolic Risk Biomarkers. A Crossover, Randomised, Controlled Trial with Two Mineral Waters in Moderately Hypercholesterolaemic Adults

Directory of Open Access Journals (Sweden)

Laura Toxqui

2016-06-01

Full Text Available Water intake is essential for health maintenance and disease prevention. The effects of an intervention with two mineral waters, sodium-bicarbonated mineral water (BW or control mineral water low in mineral content (CW, on cardiometabolic risk biomarkers were studied. In a randomised-controlled crossover-trial, sixty-four moderately hypercholesterolaemic adults were randomly assigned to consume 1 L/day of either BW (sodium, 1 g/L; bicarbonate, 2 g/L or CW with the main meals for eight weeks, separated by an eight-week washout period. Blood lipids, lipid oxidation, glucose, insulin, aldosterone, urine pH, urinary electrolytes, blood pressure, body weight, fluid intake, energy, and nutrients from total diet and beverages were determined. Total cholesterol, LDL cholesterol, and glucose decreased (p < 0.01, oxidised LDL tended to decrease (p = 0.073, and apolipoprotein B increased during the intervention, without water type effect. Energy and carbohydrates from beverages decreased since soft drinks and fruit juice consumptions decreased throughout the trial. BW increased urinary pH (p = 0.006 and reduced calcium/creatinine excretion (p = 0.011. Urinary potassium/creatinine decreased with both waters. Consumption of 1 L/day of mineral water with the main meals reduces cardiometabolic risk biomarkers, likely to be attributed to a replacement of soft drinks by water. In addition, BW does not affect blood pressure and exerts a moderate alkalizing effect in the body.

A pilot study comparing opaque, weighted bottles with conventional, clear bottles for infant feeding.

Science.gov (United States)

Ventura, Alison K; Pollack Golen, Rebecca

2015-02-01

It is hypothesized that the visual and weight cues afforded by bottle-feeding may lead mothers to overfeed in response to the amount of liquid in the bottle. The aim of the present pilot study was to test this hypothesis by comparing mothers' sensitivity and responsiveness to infant cues and infants' intakes when mothers use opaque, weighted bottles (that remove visual and weight cues) compared to conventional, clear bottles to feed their infants. We also tested the hypothesis that mothers' pressuring feeding style would moderate the effect of bottle type. Formula-feeding dyads (N = 25) visited our laboratory on two separate days. Mothers fed their infants from a clear bottle one day and an opaque, weighted bottle on the other; bottle-order was counterbalanced across the two days. Infant intake was assessed by weighing each bottle before and after the feeding. Maternal sensitivity and responsiveness to infant cues was objectively assessed using the Nursing Child Assessment Feeding Scale. Mothers were significantly more responsive to infant cues when they used opaque compared to clear bottles (p = .04). There was also a trend for infants to consume significantly less formula when fed from opaque compared to clear bottles (p = .08). Mothers' pressuring feeding style moderated the effect of bottle type on maternal responsiveness to infant cues (p = .02) and infant intake (p = .03). Specifically, mothers who reported higher levels of pressuring feeding were significantly more responsive to their infants' cues (p = .02) and fed their infants significantly less formula when using opaque versus clear bottles (p = .01); no differences were seen for mothers who reported lower levels of pressuring feeding. This study highlights a simple, yet effective intervention for improving the bottle-feeding practices of mothers who have pressuring feeding styles. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Moderating Role of Risk Perception on The Relationship Between Satisfaction and Repurchase Intention of Bottled Water in Nigeria: A Research Proposition

Directory of Open Access Journals (Sweden)

Wahid N. Abdul

2018-01-01

Full Text Available There has been a surge of bottled water consumption globally to date. This phenomenon requires investigation on why consumers intend to repeat purchase the product. While past literature has applied Oliver’s expectation disconfirmation theory (EDT to explain the link between customer satisfactions (CS and repurchase intention (RI, other studies have reported conflicting findings. Thus, this study argues that risk perception (RP should be added as a moderating variable between CS-RI which should improve our understanding of the RI behaviour in the context of EDT, bottled water consumption, policy and marketing strategy research. A new framework is proposed to explain the role of RP in EDT, with the aim of stimulating further enquiry.

Panel Board From Coconut Fibre And Pet Bottle

Directory of Open Access Journals (Sweden)

Ngadiman Norhayati

2018-01-01

Full Text Available The rate of global deforestation and its impact on the environment has led particle board manufacture to search for alternative feedstock, especially in countries where wood is less available compared to other cellulosic natural product. Based on the properties of coconut fibre and PET bottle, these two materials can be recycle as raw material for manufacture of panel board. As for this study, the coconut fibre were used as the filler and PET bottle as outer lining of the panel board. Two types of coconut fibre were used which are grinding and un-grinding coconut fibre. At first, the coconut fibre are undergoes softening, grinding, drying and sieving process, while PET bottle was cleaning, shredding, sieving before compacted using hydraulic hot press machine. There are four types of testing that been carried out which are swelling, water absorption, Modulus of Elasticity (MOE and Modulus of Rupture (MOR. The result show the conventional board has the highest value for MOE test, so it’s indicate that the conventional board is less strength from the coconut fibre board. As for water absorption test, the average water absorption of coconut fibre based panel board is less than conventional board. Overall, the coconut fibre board is better than conventional panel board because coconut fibre board are less swelling, has low water absorption, high modulus of rupture and low modulus of elasticity. Based on the finding, this coconut fibre panel board has potential as a stronger and long-lasting panel board than the conventional board in the market. Other than that, the panel also have their own aesthetic value since the recycled plastic bottle used as outer lining is colourful and giving aesthetic value.

[Determination of sodium, magnesium, calcium, lithium and strontium in natural mineral drinking water by microwave plasma torch spectrometer with nebulization sample introduction system].

Science.gov (United States)

Zhou, Wei; Xiong, Hai-long; Feng, Guo-dong; Yu, Ai-min; Chen, Huan-wen

2014-06-01

The microwave plasma torch (MPT) was used as the emission light source. Aqueous samples were introduced with a nebulizer and a desolvation system. A method for the determination of Na, Mg, Ca, Li and Sr in natural mineral drinking water by argon microwave plasma torch spectrometer (ArMPT spectrometer) was established. The effects of microwave power, flow rate of carrier gas and support gas were investigated in detail and these parameters were optimized. Under the optimized condition, the experiments for the determination of Na, Mg, Ca, Li and Sr in 11 kinds of bottled mineral drinking water were carried out by ArMPT spectrometer. The limit-of-detection (LOD) of Na, Mg, Ca, Li and Sr was found to be 4.4, 21, 56, 11 and 84 μg x mL(-1), respectively. Relative standard deviation (n = 6) was in the range of 1.30%-5.45% and standard addition recoveries were in the range of 84.6%-98.5%. MPT spectrometer was simpler, more convenient and of lower cost as compared to ICP unit. MPT spectrometer demonstrated its rapid analysis speed, accuracy, sensitivity and simultaneous multi element analysis ability during the analysis process. The results showed that MPT spectrometer was suitable for metal elements detection for natural mineral drinking water. This approach provides not only one way for resisting the illegal dealings, but also a security for the quality of drinking water. Moreover, the usability of MPT spectrometer in the field of food security; drug safety; clinical diagnostic is promised.

[Investigation of concentration levels of chromium(VI) in bottled mineral and spring waters by high performance ion chromatography technique with application of postcolumn reaction with 1,5-diphenylcarbazide and VIS detection].

Science.gov (United States)

Swiecicka, Dorota; Garboś, Sławomir

2008-01-01

The aim of this work was optimization and validation of the method of determination of Cr(VI) existing in the form of chromate(VI) in mineral and spring waters by High Performance Ion Chromatography (HPIC) technique with application of postcolumn reaction with 1,5-diphenylcarbazide and VIS detection. Optimization of the method performed with the use of initial apparatus parameters and chromatographic conditions from the Method 218.6 allowed to lowering detection limit for Cr(VI) from 400 ng/l to 2 ng/l. Thanks to very low detection limit achieved it was possible to determine of Cr(VI) concentrations in 25 mineral and spring waters presented at Polish market. In the cases of four mineral and spring waters analyzed, determined Cr(VI) concentrations were below of quantification limit (waters the concentrations of chromium(VI) were determined in the range of 5.6 - 1281 ng/l. The fact of existence of different Cr(VI) concentrations in investigated waters could be connected with secondary contamination of mineral and spring waters by chromium coming from metal installations and fittings. One should be underlined that even the highest determined concentration level of chromium(VI) was below of the maximum admissible concentration of total chromium presented in Polish Decree of Minister of Health from April 29th 2004. Therefore after taking into account determined in this work concentration of Cr(VI), the consumption of all waters analyzed in this study does not lead to essential human health risk.

Microcoulometric measurement of water in minerals

Science.gov (United States)

Cremer, M.; Elsheimer, H.N.; Escher, E.E.

1972-01-01

A DuPont Moisture Analyzer is used in a microcoulometric method for determining water in minerals. Certain modifications, which include the heating of the sample outside the instrument, protect the system from acid gases and insure the conversion of all hydrogen to water vapor. Moisture analyzer data are compared to concurrent data obtained by a modified Penfield method. In general, there is a positive bias of from 0.1 to 0.2% in the moisture analyzer results and a similarity of bias in minerals of the same kind. Inhomogeneity, sample size, and moisture pick-up are invoked to explain deviations. The method is particularly applicable to small samples. ?? 1972.

Effects of Sunlight Exposure on the Quality Parameters of Bottled ...

African Journals Online (AJOL)

PROF HORSFALL

microbial population (total coliform) of the bottled water with increasing exposure to sunlight was observed. ... safe drinking water which has led to the tremendous ... degradation under high temperature (Bach et al., ..... Solar and photocatalytic.

Interactive baby feeding bottle

NARCIS (Netherlands)

2013-01-01

An interactive baby bottle with an electronic unit is disclosed. The electronic unit comprises a sensor unit configured to sense the heart beat of a person bottle feeding a baby and an actuator unit configured to transmit the sensed heart beat to the baby. The disclosed interactive baby bottle can

THE USE OF FLUORIDE CONTAINING MINERAL WATER IN WORT PRODUCTION

Directory of Open Access Journals (Sweden)

Gunka Yonkova

2011-12-01

Full Text Available The present work aims to study the quality of wort produced using fluoride containing mineral water. The results show that the mineral water has a negative impact on the enzymatic destruction of starch, proteins, color intensity and pH of the wort. The changes of pH during mashing process using tap and mineral water was studied. The lower acidity of wort obtained using mineral water didn’t change during the brewing process. The fluoride content of beer is lower than 5 mg.L-1 when wort is produced using mineral and tap water in 1:1 ratio and citric acid for pH correction. At the same time, the final degree of fermentation, α-amine nitrogen content and the intensity of color of produced wort are close to the control sample. The changes in fluoride ion concentration are monitored using ion-selective potentiometry. The fluoride content is decreased from 5.7 to 4.75 mg.L-1, the most intense change is observed during the mashing process.

Stopping the Bottle

Science.gov (United States)

... difficult it can be to break the bottle habit. Longer bottle use may lead to cavities or ... Drinks for Kids Toddlers at the Table: Avoiding Power Struggles View more About Us Contact Us Partners ...

Water physics and chemistry data from bottle casts from FIXED PLATFORM from 26 April 1972 to 06 December 1972 (NODC Accession 7400880)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from MULTIPLE SHIPS from 26 April 1972 to 06 December 1972. Data were submitted by Edgerton,...

Gross alpha and beta activities in Tunisian mineral water

International Nuclear Information System (INIS)

Hamrouni Benbelgacem, Samar

2011-01-01

The quality of natural mineral water is a universal health problem seeing its vital importance. This problem is related to the presence of the radionuclides since this water is coming from underground, during their circulation it dissolves and conveys the radionuclides which are present in the earth's crust. This problem which leads to the contamination of the mineral water urged the World Health Organization to set standards and to recommend the respect of the median values of the activities alpha and beta within the framework of the man protection against this internal exhibition. Concerning the radiological quality of Tunisian mineral water studied in this project, we showed, by using the gross alpha and beta activities counting, that this water is specific to human consumption since their gross alpha and beta activities do not forward any risk on health.

Determinants of using pacifier and bottle feeding

Directory of Open Access Journals (Sweden)

Gabriela dos Santos Buccini

2014-08-01

Full Text Available OBJECTIVE To analyze the factors associated with the use of pacifiers and/or bottle feeding in infants aged under one year. METHODS This is a cross-sectional study with 34,366 children and using data from the database of the 2nd Nationwide Survey of Breastfeeding Prevalence performed in the Brazilian capitals and Federal District in 2008. Cluster sampling was used. The questionnaire included questions about the use of artificial nipples in the last 24 hours. The analysis considered three outcomes: exclusive use of pacifier, exclusive use of bottle feeding, and use of artificial nipples (pacifier and bottle feeding. Prevalence ratios were obtained using Poisson regression with robust variance following a hierarchical model. RESULTS The following factors were associated with exclusive use of the pacifier: mother working outside the home, primiparity, child was not breastfed within the first hour, and child had consumed tea on the first day at home. The following factors were associated with exclusive use of bottle feeding: mother working outside the home, primiparity, low birth weight, child not breastfed within the first hour, and child had consumed milk formula and tea on the first day at home. The following factors were associated with use of artificial nipples (pacifier and bottle feeding: mother working outside the home, primiparity, cesarean delivery, the male gender, low birth weight, born in a hospital not accredited as “baby friendly”, required health baby monitoring in the Primary Health Care Unit (PR = 0.91, and child had consumed milk formula, water, or tea on the first day at home. CONCLUSIONS This study identified profiles of exclusive users of pacifiers, bottle feeding, and both. The provided information can guide preventive practices for child health.

Determination of As, Cd, and Pb in Tap Water and Bottled Water Samples by Using Optimized GFAAS System with Pd-Mg and Ni as Matrix Modifiers

Directory of Open Access Journals (Sweden)

Sezgin Bakırdere

2013-01-01

Full Text Available Arsenic, lead, and cadmium were determined in tap and bottled water samples consumed in the west part of Turkey at trace levels. Graphite furnace atomic absorption spectrometry (GFAAS was used in all detections. All of the system parameters for each element were optimized to increase sensitivity. Pd-Mg mixture was selected as the best matrix modifier for As, while the highest signals were obtained for Pb and Cd in the case of Ni used as matrix modifier. Detection limits for As, Cd, and Pb were found to be 2.0, 0.036, and 0.25 ng/mL, respectively. 78 tap water and 17 different brands of bottled water samples were analyzed for their As, Cd, and Pb contents under the optimized conditions. In all water samples, concentration of cadmium was found to be lower than detection limits. Lead concentration in the samples analyzed varied between N.D. and 12.66 ± 0.68 ng/mL. The highest concentration of arsenic was determined as 11.54 ± 2.79 ng/mL. Accuracy of the methods was verified by using a certified reference material, namely, Trace Element in Water, 1643e. Results found for As, Cd, and Pb in reference materials were in satisfactory agreement with the certified values.

MINERAL WATERS IN RUPEA CITY: PHYSICOCHEMICAL FEATURES AND USE

Directory of Open Access Journals (Sweden)

R. MEREŢ

2016-03-01

Full Text Available This paper aims to analyse and highlight certain specificities of mineral waters in Rupea city (Braşov County: physicochemical characteristics, a short history of their use, and future use options. The article is based on the synthesis and analysis of information obtained from scientific papers, archival sources, and field investigations conducted between 2010 and 2015. Rupea City is located in the area situated at the contact between the Transylvanian Subcarpathians the Hârtibaciului Plateau, at 64 km northwest of Braşov and 53 km southeast of Sighişoara. The presence of the salt layer in the Tortonian deposits (Miocene at different depths and thickness accounts for the occurrence of concentrated chlorinated-sodic waters, discovered as early as the second half of the 19th century. The first analyses of the Rupea mineral waters were conducted by Henrik Muller (1856, who considered the mineral waters at Băile Cohalm (old name of the Rupea city to be “among the few chlorinated-sodic-sulphated waters of Transylvania”. The measurements conducted on physico-geographical parameters in the study period and the analysis of water samples performed in specialized laboratories showed that these mineral waters preserved their physicochemical characteristics (chorosodic, sulphated, hypertonic, athermal and, consequently, can be used for therapeutic purposes as was the case in the past. The pavilions of the old spa establishment “survived” until the year 2003 when they began to be gradually demolished, and the mineral water storage basins were consolidated and covered. The only one which is still currently being used (for household activities or sheepfold cheese processing is the “muriatic” salt water from the well locals call “Slatina”, located 1.5 km east towards Homorod, in close proximity to Cozd River (ancient name of the Valea Mare River.

Plasma sterilization of polyethylene terephthalate bottles by pulsed corona discharge at atmospheric pressure.

Science.gov (United States)

Masaoka, Satoshi

2007-06-01

A pulsed power supply was used to generate a corona discharge on a polyethylene terephthalate bottle, to conduct plasma sterilization at atmospheric pressure. Before generating such a discharge, minute quantities of water were attached to the inner surface of the bottle and to the surface of a high voltage (HV) electrode inserted into the bottle. Next, high-voltage pulses of electricity were discharged between electrodes for 6.0s, while rotating the bottle. The resulting spore log reduction values of Bacillus subtilis and Aspergillus niger on the inner surface of the bottle were 5.5 and 6 or higher, respectively, and those on the HV electrode surface were each 6 or higher for both strains. The presence of the by-products gaseous ozone, hydrogen peroxide, and nitric ions resulting from the electrical discharge was confirmed.

Water physics and chemistry data from bottle casts from the TAGE from 08 May 1969 to 30 December 1969 (NODC Accession 7100605)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from the TAGE from 08 May 1969 to 30 December 1969. Data were submitted by the Stanford University;...

Evaluation of Nevsehir mineral waters by using hydrochemical and isotopic data, central Anatolia, Turkey

International Nuclear Information System (INIS)

Afsin, M.; Kavurmaci, M.

2002-01-01

Many mineral waters are located in Nevsehir and its vicinity. Corak, Karakaya and Guemueskent mineral waters are investigated in this study. The springs generally emerge along faults in the study area. The marbles of the Bozcaldag metamorphic basement rocks form the confined aquifer of the springs. The hydrochemical facies of the springs are Na-Ca-HCO 3 of Karakaya cold springs, Ca-HCO 3 of Guemueskent mineral waters; and Na-Cl-HCO 3 of Corak and Karakaya mineral waters, respectively. Because of the gas-mineral-water interaction, total mineralizations are high in a CO 2 dominated and low temperature mineral waters. The springs are of meteoric origin. Corak and Karakaya mineral waters might be contributed by older waters. The Karakaya cold spring is shallow circulated, while the mineral waters which have high the free CO 2 -gas are circulated groundwaters. In addition to the old travertines extending along faultlines, recent travertine depositions appear in places where mineral waters appear. The travertines in these regions are formed under certain conditions including low flow depth, turbulent flow, increasing pH values due to the loss of CO 2

A pilot study comparing opaque, weighted bottles with conventional, clear bottles for infant feeding

OpenAIRE

Ventura, Alison K.; Golen, Rebecca Pollack

2014-01-01

Compared to breast-fed infants, bottle-fed infants consume greater volumes and gain more weight during infancy. It is hypothesized that the visual and weight cues afforded by bottle-feeding may lead mothers to overfeed in response to the amount of liquid in the bottle. The aim of the present pilot study was to test this hypothesis by comparing mothers’ sensitivity and responsiveness to infant cues and infants’ intakes when mothers use opaque, weighted bottles (that remove visual and weight cu...

Design and performance of a vacuum-bottle solid-state calorimeter

International Nuclear Information System (INIS)

Bracken, D.S.; Biddle, R.; Cech, R.

1997-01-01

EG and G Mound Applied Technologies calorimetry personnel have developed a small, thermos-bottle solid-state calorimeter, which is now undergoing performance testing at Los Alamos National Laboratory. The thermos-bottle solid-state calorimeter is an evaluation prototype for characterizing the heat output of small heat standards and other homogeneous heat sources. The current maximum sample size is 3.5 in. long with a diameter of 0.8 in. The overall size of the thermos bottle and thermoelectric cooling device is 9.25 in. high by 3.75 in. diameter and less than 3 lb. Coupling this unit with compact electronics and a laptop computer makes this calorimeter easily hand carried by a single individual. This compactness was achieved by servo controlling the reference temperature below room temperature and replacing the water bath used in conventional calorimeter design with the thermos-bottle insulator. Other design features will also be discussed. The performance of the calorimeter will be presented

Mineral concentrations in diets, water, and milk and their value in estimating on-farm excretion of manure minerals in lactating dairy cows.

Science.gov (United States)

Castillo, A R; St-Pierre, N R; Silva del Rio, N; Weiss, W P

2013-05-01

Thirty-nine commercial dairies in Merced County, California were enrolled in the present study to (1) compare lactating cow mineral intakes (via drinking water and total mixed ration) to the National Research Council (NRC) requirements, (2) evaluate the association between dietary concentrations of minerals with and without drinking water and adjusted for mineral concentrations in milk, and (3) compare 4 different methods to estimate excretion of minerals using either assays or estimations of milk mineral outputs and total daily mineral intake per cow with or without minerals coming from drinking water. Dairies were selected to represent a range of herd milk yields and a range of water mineral contents. Samples of total mixed ration, drinking water, and bulk tank milk were taken on 2 different days, 3 to 7d apart in each farm. Across-farm medians and percentile distributions were used to analyze results. The herd median milk yield interquartile ranged (10th to 90th percentile) from less than 25 to more than 39 kg/d and the concentration of total solids in water interquartile ranged from less than 200 to more than 1,490 mg/L. Including drinking water minerals in the diets increased dietary concentrations by minerals except for Na and Cl, which increased by 9.3 and 6.5%, respectively. Concentrations of P and K in milk were essentially the same as the NRC value to estimate lactation requirements. However, NRC milk values of Ca, Cl, and Zn were 10 to 20% greater than dairy farm values; and Na, Cu, Fe, and Mn were no less than 36% below NRC values. Estimated excretion of minerals via manure varied substantially across farms. Farms in the 10th percentile did have 2 to 3 times less estimated mineral excretions than those in the 90th percentile (depending on the mineral). Although including water minerals increased excretion of most minerals, the actual median effect of Ca, Mg, S, Cu, Fe, and Mn was less than 5%, and about 8% for Na and Cl. Replacing assayed concentrations

On the genesis and dynamics of mineral waters of Essentuki deposit in the Great Region of Caucasian Mineral Waters on the basis of uranium isotope information

International Nuclear Information System (INIS)

Chalov, P.I.; Tikhonov, A.I.; Kiselev, G.P.; Merkulova, K.I.

1991-01-01

The sources of the Great Region of Caucasian Mineral Waters are established and contribution of each source in the formation of this region is determined using the data on isotopic ratio and content of uranium in mineral waters. The investigation relies on the fact that 234 U/ 238 U radioactivity ratio used as a tracer in different for waters which drain the rocks with different content and distribution of uranium therein. The investigation results reveal the peculiarities of the geological history of the above region and can be used for predicting new deposits of mineral waters

Effects of waste PET bottles aggregate on the properties of concrete

International Nuclear Information System (INIS)

Choi, Yun-Wang; Moon, Dae-Joong; Chung, Jee-Seung; Cho, Sun-Kyu

2005-01-01

This paper investigates the surface microstructure of waste polyethylene terephthalate (PET) bottles lightweight aggregate (WPLA) to examine the effect of granulated blast-furnace slag (GBFS) on WPLA. The WPLA was made from the waste PET bottles and GBFS, and experimental tests were conducted on compressive strength, splitting tensile strength, modulus of elasticity, slump, and density of waste PET bottles lightweight aggregate concrete (WPLAC). The 28-day compressive strength of WPLAC with the replacement ratio of 75% reduces about 33% compared to the control concrete in the water-cement ratio of 45%. The density of WPLAC varies from 1940 to 2260 kg/m 3 by the influence of WPLA. The structural efficiency of WPLAC decreases as the replacement ratio increases. The workability of concrete with 75% WPLA improves about 123% compared to that of the normal concrete in the water-cement ratio of 53%. The adhered GBFS is able to strengthen the surface of WPLA and to narrow the transition zone owing to the reaction with calcium hydroxide

A complete life cycle assessment of high density polyethylene plastic bottle

Science.gov (United States)

Treenate, P.; Limphitakphong, N.; Chavalparit, O.

2017-07-01

This study was aimed to determine environmental performances of a lubricant oil bottle made from high density polyethylene and to develop potential measures for reducing its impacts. A complete life cycle assessment was carried out to understand a whole effect on the environment from acquiring, processing, using, and disposing the product. Two scenarios of disposal phase; recycle and incineration: were examined to quantify a lesser degree on environmental impact. The results illustrated that major impacts of the two scenarios were at the same categories with the highest contributor of raw material acquisition and pre-processing. However, all impacts in case of recycling provided a lower point than that in case of incineration, except mineral extraction. Finally, feasible measures for reducing the environmental impact of high density polyethylene plastic bottle were proposed in accordance with 3Rs concept.

Water physics and chemistry data from bottle casts from the BLUE FIN from 1976-02-26 to 1976-05-26 (NODC Accession 7800050)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from the BLUE FIN from 26 February 1976 to 26 May 1976. Data were submitted by the Skidaway...

Discharge, water temperature, and water quality of Warm Mineral Springs, Sarasota County, Florida: A retrospective analysis

Science.gov (United States)

Metz, Patricia A.

2016-09-27

Warm Mineral Springs, located in southern Sarasota County, Florida, is a warm, highly mineralized, inland spring. Since 1946, a bathing spa has been in operation at the spring, attracting vacationers and health enthusiasts. During the winter months, the warm water attracts manatees to the adjoining spring run and provides vital habitat for these mammals. Well-preserved late Pleistocene to early Holocene-age human and animal bones, artifacts, and plant remains have been found in and around the spring, and indicate the surrounding sinkhole formed more than 12,000 years ago. The spring is a multiuse resource of hydrologic importance, ecological and archeological significance, and economic value to the community.The pool of Warm Mineral Springs has a circular shape that reflects its origin as a sinkhole. The pool measures about 240 feet in diameter at the surface and has a maximum depth of about 205 feet. The sinkhole developed in the sand, clay, and dolostone of the Arcadia Formation of the Miocene-age to Oligocene-age Hawthorn Group. Underlying the Hawthorn Group are Oligocene-age to Eocene-age limestones and dolostones, including the Suwannee Limestone, Ocala Limestone, and Avon Park Formation. Mineralized groundwater, under artesian pressure in the underlying aquifers, fills the remnant sink, and the overflow discharges into Warm Mineral Springs Creek, to Salt Creek, and subsequently into the Myakka River. Aquifers described in the vicinity of Warm Mineral Springs include the surficial aquifer system, the intermediate aquifer system within the Hawthorn Group, and the Upper Floridan aquifer in the Suwannee Limestone, Ocala Limestone, and Avon Park Formation. The Hawthorn Group acts as an upper confining unit of the Upper Floridan aquifer.Groundwater flow paths are inferred from the configuration of the potentiometric surface of the Upper Floridan aquifer for September 2010. Groundwater flow models indicate the downward flow of water into the Upper Floridan aquifer

Decorporation of mixture of strontium and cesium isotopes with domestic mineral waters

International Nuclear Information System (INIS)

Slavov, S.; Filev, G.; Kiradzhiev, G.

1990-01-01

The possibilities of Bulgarian mineral waters to decorporate mixtures of strontium and cesium radioisotopes, simultaneous entering the body, were studied. A modified effect in respect to radioactive strontium was found. Modification of the effect of mixing two diferent types of mineral waters was not proven. No effect was found of potassium-containing mineral water on radioactive cesium kinetics. 1 tab., 7 refs

27 CFR 4.26 - Estate bottled.

Science.gov (United States)

2010-04-01

... bottled. (a) Conditions for use. The term Estate bottled may be used by a bottling winery on a wine label only if the wine is labeled with a viticultural area appellation of origin and the bottling winery: (1... owned or controlled by the winery within the boundaries of the labeled viticultural area; (3) crushed...

On the mineralization model of 'three sources--heat, water and uranium'

International Nuclear Information System (INIS)

Li Xueli

1992-01-01

In response to the relations between geological and geothermal settings, geothermal water and uranium mineralizations in the Southeastern China, the model of uranium mineralization in discharge area (depressurization area) of fossil geothermal systems in Mesozoic-Cenozoic Volcanic-magmatic active areas has been put forward and expounded in the view of mineral-formation by the 'three sources'-heat, water and uranium

Uranium mineralization by ground water in sedimentary rocks, Japan

International Nuclear Information System (INIS)

Doi, K.; Hirono, S.; Sakamaki, Y.

1975-01-01

To solve the mechanism of uranium concentration in stratabound uranium deposits occurring in the basal part of Neogene sediments overlying granite basement, attention was paid to uranium leaching from weathered granite by circulating carbonated fissure waters, to effective adsorbents for fixing uranium from uraniferous ground waters, to structural features controlling the ground-water circulation, and other relevant factors. The evidence for uranium transportation by hydothermal solutions, including hot spring waters, is hard to observe. Conclusions are summarized as follows: Uranium in the deposits is supplied from surrounding source rocks, mostly from granite. Uranium is transported by circulating ground-water solutions. The uranium dissolved in ground water is fixed in minerals in various ways, the most important being adsorption by carbonaceous matter. Ore-grade uranium concentrated from very dilute solutions occurs by multiple repetition of a leaching-and-fixation cycle between minerals or adsorbents and circulating uraniferous ground water. Important factors for uranium mineralization are sufficient uranium, supplied mostly from granite, the existence of effective adsorbents such as carbonaceous matter in the host rocks, and favorable geological, geochemical, and geophysical environments. The last seem to require not only physical and chemical conditions but also correct flow and volume of ground water. (U.S.)

Trace uranium determination in beverages and mineral water using fission track techniques

International Nuclear Information System (INIS)

Cheng, Y.L.; Lin, J.Y.; Hao, X.H.

1993-01-01

The uranium contents of beverages and mineral water have been estimated using the technique of fission track analysis with polycarbonate detector. The U contents in beverages have been found to vary from 0.26 ± 0.03 to 1.65 ± 0.07 ppb, the average value is 0.93 ± 0.05 ppb. The mean U content in mineral water is 9.20 ± 0.16 ppb, which is ∼ 10 times higher than the mean U content of beverages. The present study shows the high U content in mineral water, indicating need for further investigation of U content in mineral water for the studies of radiation health hazards. (Author)

Prevalence and Genetic Diversity of Enterococcus faecalis Isolates from Mineral Water and Spring Water in China

Directory of Open Access Journals (Sweden)

Lei Wei

2017-06-01

Full Text Available Enterococcus faecalis is an important opportunistic pathogen which is frequently detected in mineral water and spring water for human consumption and causes human urinary tract infections, endocarditis and neonatal sepsis. The aim of this study was to determine the prevalence, virulence genes, antimicrobial resistance and genetic diversity of E. faecalis from mineral water and spring water in China. Of 314 water samples collected from January 2013 to January 2014, 48 samples (15.3% were contaminated E. faecalis. The highest contamination rate occurred in activated carbon filtered water of spring water (34.5%, followed by source water of spring water (32.3% and source water of mineral water (6.4%. The virulence gene test of 58 E. faecalis isolates showed that the detection rates of asa1, ace, cylA, gelE and hyl were 79.3, 39.7, 0, 100, 0%, respectively. All 58 E. faecalis isolates were not resistant to 12 kinds of antibiotics (penicillin, ampicillin, linezolid, quinupristin/dalfopristin, vancomycin, gentamicin, streptomycin, ciprofloxacin, levofloxacin, norfloxacin, nitrofurantoin, and tetracycline. Enterobacterial repetitive intergenic consensus-PCR classified 58 isolates and three reference strains into nine clusters with a similarity of 75%. This study is the first to investigate the prevalence of E. faecalis in mineral water and spring water in China. The results of this study suggested that spring water could be potential vehicles for transmission of E. faecalis.

Post-consumer contamination in high-density polyethylene (HDPE) milk bottles and the design of a bottle-to-bottle recycling process.

Science.gov (United States)

Welle, F

2005-10-01

Six hundred conventional recycled HDPE flake samples, which were recollected and sorted in the UK, were screened for post-consumer contamination levels. Each analysed sample consisted of 40-50 individual flakes so that the amount of analysed individual containers was in the range 24,000-30,000 post-consumer milk bottles. Predominant contaminants in hot-washed flake samples were unsaturated oligomers, which can be also be found in virgin high-density polyethylene (HDPE) pellet samples used for milk bottle production. In addition, the flavour compound limonene, the degradation product of antioxidant additives di-tert-butylphenol and low amounts of saturated oligomers were found in higher concentrations in the post-consumer samples in comparison with virgin HDPE. However, the overall concentrations in post-consumer recycled samples were similar to or lower than concentration ranges in comparison with virgin HDPE. Contamination with other HDPE untypical compounds was rare and was in most cases related to non-milk bottles, which are HDPE and on the high cleaning efficiency of the super-clean recycling process especially for highly volatile compounds, the recycling process investigated is suitable for recycled post-consumer HDPE bottles for direct food-contact applications. However, hand-picking after automatically sorting is recommended to decrease the amount of non-milk bottles. The conclusions for suitability are valid, provided that the migration testing of recyclate contains milk bottles up to 100% and that both shelf-life testing and sensorial testing of the products are successful, which are topics of further investigations.

The main chemical properties of hot and cold mineral waters in Bayankhongor, Mongolia

Directory of Open Access Journals (Sweden)

D Oyuntsetseg

2014-12-01

Full Text Available In the current study, hot and cold mineral springs and sub mineral waters in the Bayankhongor province were examined for their chemical characteristics and identified cold mineral waters classification according to mineral water classification of Mongolia. The hot spring waters belong to Na+-HCO3- and Na+-SO42- types. The cold mineral spring of Lkham belongs to Ca2+-HCO3- type. All sub mineral waters are generally located in the two areas (northern part or mountain forest area and the southern part or Gobi desert area. TDS concentrations of cold springs of the southern part in the study area were higher than northern part’s cold springs. The total dissolved silica content of cold spring was ranged from 4.5mg/L to 26 mg/L which did not correspond to requirements of mineral water standard of Mongolia. Thus, these cold springs are belonging to sub mineral water classification. The sub mineral waters were characterized into four types such as a Ca2+-SO42-, Na+-SO42-, Na+-HCO3 and Ca2+ - HCO3 by their chemical composition in the study area. The values for the quartz, chalcedony geothermometer and the Na/K geothermometer were quite different. The silica-enthalpy mixing model predicts a subsurface reservoir temperature between 124 and 197°C and most of the hot waters have been  probably mixed with cold water. The result shows that an averaged value of calculated temperature ranges from 77°C to 119°C which indicates that studied area has low temperature geothermal resources. DOI: http://doi.dx.org/10.5564/mjc.v15i0.324 Mongolian Journal of Chemistry 15 (41, 2014, p56-62

Water in Nominally Anhydrous Minerals from Nakhlites and Shergottites

Science.gov (United States)

Peslier, Anne H.

2013-01-01

Estimating the amount of water in the interior of terrestrial planets has tremendous implications on our understanding of solar nebula evolution, planet formation and geological history, and extraterrestrial volcanism. Mars has been a recent focus of such enquiry with complementary datasets from spacecrafts, rovers and martian meteorite studies. In planetary interiors, water can be dissolved in fluids or melts and hydrous phases, but can also be locked as protons attached to structural oxygen in lattice defects in nominally anhydrous minerals (NAM) such as olivine, pyroxene, or feldspar [1-3]. Measuring water in Martian meteorite NAM is challenging because the minerals are fragile and riddled with fractures from impact processes that makes them break apart during sample processing. Moreover, curing the sample in epoxy causes problems for the two main water analysis techniques, Fourier transform infrared spectrometry (FTIR) and secondary ionization mass spectrometry (SIMS). Measurements to date have resulted in a heated debate on how much water the mantle of Mars contains. SIMS studies of NAM [4], amphiboles [5], and apatites [6-8] from Martian meteorites report finding enough water in these phases to infer that the martian mantle is as hydrous as that of the Earth. On the other hand, a SIMS study of glass in olivine melt inclusions from shergottites concludes that the Martian mantle is much drier [9]. The latter interpretation is also supported by the fact that most martian hydrous minerals generally have the relevant sites filled with Cl and F instead of H [10,11]. As for experimental results, martian basalt compositions can be reproduced using water as well as Cl in the parent melts [12,13]. Here FTIR is used to measure water in martian meteorite minerals in order to constrain the origin of the distribution of water in martian meteorite phases.

Water exchange rate in RAS and dietary inclusion of micro-minerals influence growth, body composition and mineral metabolism in common carp

NARCIS (Netherlands)

Antony Jesu Prabhu, P.; Kaushik, S.J.; Geurden, I.; Stouten, T.; Fontagné-dicharry, S.; Veron, V.; Mariojouls, C.; Verreth, J.A.J.; Eding, E.H.; Schrama, J.W.

2017-01-01

Recirculation aquaculture systems (RASs) operated at low water exchange rates are known to accumulate minerals in the water. This study examined the dietary mineral requirement and metabolism in common carp reared in RAS of contrasting water exchange rates. Two independent RAS (water exchange rates,

Application of Emotional Branding Strategy in the Model Development of Sports Brand of The Bottled Water Market

OpenAIRE

Marija Jankovic

2017-01-01

The new economy has brought new meaning to the brand, which is characterized by a brand, but also has a human touch, turning into an emotional brand. Alternative branding strategies put emphasis on brand experience in terms of emotional, holistic and socially responsible. Bottled water has become the world's "liquid gold" in the last 40 years, because it is a natural product, which is made with minimal costs. The paper develops the idea to perform a kind of humanization and the introduction o...

Origins of high pH mineral waters from ultramafic rocks, Central Portugal

Energy Technology Data Exchange (ETDEWEB)

Marques, Jose M. [Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001, Lisboa (Portugal)], E-mail: jose.marques@ist.ult.pt; Carreira, Paula M. [Instituto Tecnologico e Nuclear, Estrada Nacional No 10, 2686-953 Sacavem (Portugal); Carvalho, Maria Rosario [Departamento de Geologia, Faculdade de Ciencias, Universidade de Lisboa, Ed. C6, 3oP, Campo Grande, 1749-016 Lisboa (Portugal); Matias, Maria J. [Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001, Lisboa (Portugal); Goff, Fraser E. [Earth and Planetary Sciences Department MSCO3-2040, University of New Mexico, Albuquerque, New Mexico 87131-000 (United States); Basto, Maria J.; Graca, Rui C.; Aires-Barros, Luis [Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001, Lisboa (Portugal); Rocha, Luis [Junta de Freguesia, Av. da Libertacao, 45-D, 7460-002, Cabeco de Vide (Portugal)

2008-12-15

This paper reviews the geochemical, isotopic ({sup 2}H, {sup 18}O, {sup 13}C, {sup 3}H and {sup 14}C) and numerical modelling approaches to evaluate possible geological sources of the high pH (11.5)/Na-Cl/Ca-OH mineral waters from the Cabeco de Vide region (Central-Portugal). Water-rock interaction studies have greatly contributed to a conceptual hydrogeological circulation model of the Cabeco de Vide mineral waters, which was corroborated by numerical modelling approaches. The local shallow groundwaters belong to the Mg-HCO{sub 3} type, and are derived by interaction with the local serpentinized rocks. At depth, these type waters evolve into the high pH/Na-Cl/Ca-OH mineral waters of Cabeco de Vide spas, issuing from the intrusive contact between mafic/ultramafic rocks and an older carbonate sequence. The Cabeco de Vide mineral waters are supersaturated with respect to serpentine indicating that they may cause serpentinization. Magnesium silicate phases (brucite and serpentine) seem to control Mg concentrations in Cabeco de Vide mineral waters. Similar {delta}{sup 2}H and {delta}{sup 18}O suggest a common meteoric origin and that the Mg-HCO{sub 3} type waters have evolved towards Cabeco de Vide mineral waters. The reaction path simulations show that the progressive evolution of the Ca-HCO{sub 3} to Mg-HCO{sub 3} waters can be attributed to the interaction of meteoric waters with serpentinites. The sequential dissolution at CO{sub 2} (g) closed system conditions leads to the precipitation of calcite, magnesite, amorphous silica, chrysotile and brucite, indicating that the waters would be responsible for the serpentinization of fresh ultramafic rocks (dunites) present at depth. The apparent age of Cabeco de Vide mineral waters was determined as 2790 {+-} 40 a BP, on the basis of {sup 14}C and {sup 13}C values, which is in agreement with the {sup 3}H concentrations being below the detection limit.

The real water consumption behind drinking water: the case of Italy.

Science.gov (United States)

Niccolucci, V; Botto, S; Rugani, B; Nicolardi, V; Bastianoni, S; Gaggi, C

2011-10-01

The real amount of drinking water available per capita is a topic of great interest for human health and the economic and political management of resources. The global market of bottled drinking water, for instance, has shown exponential growth in the last twenty years, mainly due to reductions in production costs and investment in promotion. This paper aims to evaluate how much freshwater is actually consumed when water is drunk in Italy, which can be considered a mature bottled-water market. A Water Footprint (WF) calculation was used to compare the alternatives: bottled and tap water. Six Italian brands of water sold in PET bottles were inventoried, analysed and compared with the public tap water of the city of Siena, as representative of the Italian context. Results showed that more than 3 L of water were needed to provide consumers with 1.50 L of drinking water. In particular, a volume of 1.50 L of PET-bottled water required an extra virtual volume of 1.93 L of water while an extra 2.13 L was necessary to supply the same volume of tap water. These values had very different composition and origin. The WF of tap water was mainly due to losses of water during pipeline distribution and usage, while WF of bottled water was greatly influenced by the production of plastic materials. When the contribution of cooling water was added to the calculation, the WF of bottled water rose from 3.43 to 6.92 L. Different strategies to reduce total water footprint are discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effects of Fish Bone Meal Flour and Mineral Water «Abalakhskaya» on Bone Mineral Density

Directory of Open Access Journals (Sweden)

A.M. Palshina

2018-03-01

Full Text Available We present the results of the complex application of fish bone meal flour (FBMF and mineral water «Abalakhskaya» (AMW for correction of calcium-phosphorus metabolism disorders in patients with abnormal bone mineral density and biliary tract pathology.

Development of Syringe/Bottle Hybrids for Sampling Slurries

International Nuclear Information System (INIS)

Coleman, C.J.

1998-01-01

A convenient and effective sample bottle system based on simple modifications of disposable plastic syringes and bottles has been devised and tested for slurry samples. Syringe/ bottle hybrids (hereafter referred to as syringe bottles) have the convenience of regular flat-bottom bottles with screw cap closures. In addition, the syringe imparts a sliding and adjustable bottom to the bottle that forces the entire contents from the bottle. The system was designed especially to collect samples for high temperature work-ups of DWPF slurry samples. The syringe bottles together with fixed-bottom sample vial inserts would provide the DWPF with convenient and reliable methods for dealing with slurry samples

Baby bottle steam sterilizers for disinfecting home nebulizers inoculated with non-tuberculous mycobacteria.

Science.gov (United States)

Towle, D; Callan, D A; Lamprea, C; Murray, T S

2016-03-01

Non-tuberculous mycobacteria (NTMb), present in environmental water sources, can contribute to respiratory infection in patients with chronic pulmonary disease. Contaminated nebulizers are a potential source of respiratory infection. Treatment with baby bottle steam sterilizers disinfects home nebulizers inoculated with bacterial pathogens but whether this method works for disinfection of NTMb is unclear. Baby bottle steam sterilization was compared with vigorous water washing for disinfecting home nebulizers inoculated with NTMb mixed with cystic fibrosis sputum. No NTMb was recovered from any nebulizers after steam treatment whereas viable NTMb grew after water washing, demonstrating that steam sterilization effectively disinfects NTMb-inoculated nebulizers. Copyright © 2015 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

[Pay attention to the human health risk of drinking low mineral water].

Science.gov (United States)

Shu, Weiqun

2015-10-01

The consumption of low mineral drinking water has been increasing around the world with the shortage of water resources and the development of advanced water treatment technologies. Evidences from systematic document reviews, ecological epidemiological observations, and experimental drinking water intervention studies indicate that lack of minerals in drinking water may cause direct or indirect harm to human health, among which, the associations of magnesium in water with cardiovascular disease, as well as calcium in water with osteoporosis, are well proved by sufficient evidence. This article points out that it is urgent to pay more attention to the issues about establishment of health risk evaluation system on susceptible consuming population, establishment of lab evaluation system on water quality and health effect for non-traditional drinking water, and program of safety mineralization for demineralized or desalinated water and so on.

A Plastic Bottle in Rectosigmoid

Directory of Open Access Journals (Sweden)

A. Derakhshanfar

2007-07-01

Full Text Available Introduction: Evaluation and treatment of foreign bodies in rectum involves careful history and physical examination. The cases of forced introduction of the objects most commonly are , sexual assault , self – introduced for anal eroticism and accidental insertion.Case Report: We describe a case of a patient with rectal impaction following self administration of a plastic bottle for anal sexual gratification. A 49 years old man was admitted in the emergency department with the history of self introduced a bottle into his rectum physical examination and abdominal X-Ray diagnosed the case as impacted foreign body in rectosigmoid. An attempt was made to deliver the bottle through the rectum but because of high lying big bottle in the sigmoid laporotomy was performed and the bottle was removed though a longitudinal incision on sigmoid colon.Conclusion: Retained rectosigmoid foreign bodies have been encountered more frequently and present a dilemma for management and rarely laporotomy for extraction of foreign bodies was performed.

Factors influencing the consumption and standards of bottled ...

African Journals Online (AJOL)

Thus, a number of companies and industries in Kenya and other developed countries have come up with bottled/packaged drinking water for sale to a wide range of consumers particularly those in urban areas. The objectives ... The brand choices were influenced by price, availability and media advertisements. More than ...

Water physics and chemistry data from bottle casts from the ASTOR and other platforms from 03 January 1958 to 17 November 1961 (NODC Accession 6800201)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from the ASTOR and other platforms from 03 January 1958 to 17 November 1961. Data were submitted by...

Water physics and chemistry data from bottle casts from the MAURY and other platforms from 01 July 1949 to 13 August 1982 (NODC Accession 8500022)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from the MAURY and other platforms from 01 July 1949 to 13 August 1982. Data were submitted by...

Synchrotron X-ray scattering studies at mineral-water interfaces

International Nuclear Information System (INIS)

Chiarello, R.P.; Sturchio, N.C.

1995-01-01

Synchrotron X-ray scattering techniques provide a powerful tool for the in situ study of atomic scale processes occurring at solid-liquid interfaces. We have applied these techniques to characterize and study reactions at mineral-water interfaces. Here we present two examples. The first is the characterization of the calcite (CaCO 3 ) (10 bar 14) cleavage surface, in equilibrium with deionized water, by crystal truncation rod measurements. The second is the in situ study of the heteroepitaxial growth of otavite (CdCO 3 ) on the calcite (10 bar 14) cleavage surface. The results of such studies will lead to significant progress in understanding mineral-water interface geochemistry

27 CFR 24.256 - Bottle aging wine.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bottle aging wine. 24.256... OF THE TREASURY LIQUORS WINE Storage, Treatment and Finishing of Wine Bottling, Packing, and Labeling of Wine § 24.256 Bottle aging wine. Wine bottled or packed and stored for the purpose of aging need...

Radium 226 and other natural radionuclides in drinking water and in beverages in the Federal Republic of Germany

International Nuclear Information System (INIS)

Gans, I.; Fusban, H.U.; Wollenhaupt, H.; Kiefer, J.; Gloebel, B.; Berlich, J.; Porstendoerfer, J.

1987-01-01

Ra-226 was detected in tap water from public water supply plants, commercial bottled mineral water, springs, wells and also in milk, beer and wine; Rn-222 was detected in tap water, springs and wells. For these kinds of water and mineral waters, exploratory measurements on the content of Pb-210, Po-210 and uranium isotopes were carried out, too. While using the new dose concept of the ICRP and with standard quantities for mineral water consumption with the highest concentration measured, only in few cases the partial body doses of 0.9 mSv/a in the critical organs is exceeded, i.e. for Ra-226 and uranium. Even in these cases, effective dose equivalents of 0.3 mSv are not reached. The resulting health hazard lies in the range which is predetermined by external exposure to terrestrial radiation. (orig./DG) With 18 tabs., 7 figs [de

Water physics and chemistry data from moored current meter and bottle casts in the Coastal Waters of New Jersey as part of the Mesa New York Bight (MESA - NYB) project, 09 April 1979 - 23 August 1979 (NODC Accession 8100440)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected using moored current meter and bottle casts in the Coastal Waters of New Jersey from April 9, 1979 to August 23,...

76 FR 63191 - Sudanese Sanctions Regulations; Iranian Transactions Regulations

Science.gov (United States)

2011-10-12

... Sudan or Iran--including vitamins and minerals, food additives and supplements, and bottled drinking... minerals, food additives and supplements, and bottled drinking water, and seeds that germinate into items... than fish and shrimp roe), dried egg albumin, live animals, Rosary/Jequirity peas, non-food-grade...

Geochemistry and origins of mineralized waters in the Floridan aquifer system, northeastern Florida

Science.gov (United States)

Phelps, G.G.

2001-01-01

Increases in chloride concentration have been observed in water from numerous wells tapping the Floridan aquifer system in northeastern Florida. Although most increases have been in the eastern part of Duval County, Florida, no spatial pattern in elevated chloride concentrations is discernible. Possible sources of the mineralized water include modern seawater intrusion; unflushed Miocene-to-Pleistocene-age seawater or connate water in aquifer sediments; or mineralized water from deeper zones of the aquifer system or from formations beneath the Floridan aquifer system. The purpose of this study was to document the chemical and isotopic characteristics of water samples from various aquifer zones, and from geochemical and hydrogeologic data, to infer the source of the increased mineralization. Water samples were collected from 53 wells in northeastern Florida during 1997-1999. Wells tapped various zones of the aquifer including: the Fernandina permeable zone (FPZ), the upper zone of the Lower Floridan aquifer (UZLF), the Upper Floridan aquifer (UFA), and both the UFA and the UZLF. Water samples were analyzed for major ions and trace constituents and for isotopes of carbon, oxygen, hydrogen, sulfur, strontium, chlorine, and boron. Samples of rock from the aquifer were analyzed for isotopes of oxygen, carbon, and strontium. In general, water from various aquifer zones cannot be differentiated based on chemistry, except for water from FPZ wells. Major-ion concentrations vary as much within the upper zone of the Lower Floridan aquifer and the Upper Floridan aquifer as between these two zones. Simple models of mixing between fresh ground water and either modern seawater or water from the FPZ as a mineralized end member show that many water samples from the UZLF aquifer and the UFA are enriched in bicarbonate, calcium, magnesium, sulfate, fluoride, and silica and are depleted in sodium and potassium (as compared to concentrations predicted by simple mixing). Chemical mass

Hydrochemical and isotopic properties of the mineralized thermal waters of Kirsehir Province, Turkey

International Nuclear Information System (INIS)

Unsal, Nail; Celik, Mehmet; Murathan, Atilla M.

2003-01-01

The main objective of this study is to determine the chemical and isotopic properties and reservoir temperature of mineralized thermal waters of Kirsehir region, Turkey. Areas which have been included in this study are Savcih, Karakurt, Terme, Bulamach and Mahmutlu. Mahmutlu and Bulamach waters are mainly of the Na-Cl type, Savcih waters are of the Na-HCO 3 -Cl type and Karakurt and Terme waters are mainly of the Ca-HCO 3 type. The Saturation Index values of the waters have been evaluated and mineralized thermal waters were found to be saturated with respect to the calcite and dolomite minerals but undersaturated with respect to the halite mineral in spite of being NaCl type. The results of hydrochemical and environmental isotope ( 18 O, D, 3 H) analyses show that the waters are of meteoric origin and have varying component of relatively old water. The reservoir temperature of the five areas of thermal manifestations fall between 50 and 100 degC. Highest temperatures of about 100 degC have been estimated for Bulamach and Mahmutlu using various chalcedony geothermometers. Mahmutlu mineralized thermal water has longer residence times and higher reservoir temperature compared to other geothermal areas in Kirsehir Province. (author)

A method for improving reliability and relevance of LCA reviews: the case of life-cycle greenhouse gas emissions of tap and bottled water.

Science.gov (United States)

Fantin, Valentina; Scalbi, Simona; Ottaviano, Giuseppe; Masoni, Paolo

2014-04-01

The purpose of this study is to propose a method for harmonising Life Cycle Assessment (LCA) literature studies on the same product or on different products fulfilling the same function for a reliable and meaningful comparison of their life-cycle environmental impacts. The method is divided in six main steps which aim to rationalize and quicken the efforts needed to carry out the comparison. The steps include: 1) a clear definition of the goal and scope of the review; 2) critical review of the references; 3) identification of significant parameters that have to be harmonised; 4) harmonisation of the parameters; 5) statistical analysis to support the comparison; 6) results and discussion. This approach was then applied to the comparative analysis of the published LCA studies on tap and bottled water production, focussing on Global Warming Potential (GWP) results, with the aim to identify the environmental preferable alternative. A statistical analysis with Wilcoxon's test confirmed that the difference between harmonised GWP values of tap and bottled water was significant. The results obtained from the comparison of the harmonised mean GWP results showed that tap water always has the best environmental performance, even in case of high energy-consuming technologies for drinking water treatments. The strength of the method is that it enables both performing a deep analysis of the LCA literature and obtaining more consistent comparisons across the published LCAs. For these reasons, it can be a valuable tool which provides useful information for both practitioners and decision makers. Finally, its application to the case study allowed both to supply a description of systems variability and to evaluate the importance of several key parameters for tap and bottled water production. The comparative review of LCA studies, with the inclusion of a statistical decision test, can validate and strengthen the final statements of the comparison. Copyright © 2014 Elsevier B.V. All

Strontium isotopic composition of hot spring and mineral spring waters, Japan

International Nuclear Information System (INIS)

Notsu, Kenji; Wakita, Hiroshi; Nakamura, Yuji

1991-01-01

In Japan, hot springs and mineral springs are distributed in Quaternary and Neogene volcanic regions as well as in granitic, sedimentary and metamorphic regions lacking in recent volcanic activity. The 87 Sr/ 86 Sr ratio was determined in hot spring and mineral spring waters obtained from 47 sites. The ratios of waters from Quaternary and Neogene volcanic regions were in the range 0.703-0.708, which is lower than that from granitic, sedimentary and metamorphic regions (0.706-0.712). The geographical distribution of the ratios coincides with the bedrock geology, and particularly the ratios of the waters in Quaternary volcanic regions correlate with those of surrounding volcanic rocks. These features suggest that subsurface materials control the 87 Sr/ 86 Sr ratios of soluble components in the hot spring and mineral spring waters. (author)

Águas minerais de algumas fontes naturais brasileiras Mineral waters from brazilian natural sources

Directory of Open Access Journals (Sweden)

M. A. P. Rebelo

1999-07-01

Full Text Available Paciente de litíase renal é estimulado a aumentar a ingestão hídrica, principalmente na forma de água tratada da torneira, pela irrelevante biodisponibilidade de minerais em sua composição. O benefício é atribuído à redução da saturação dos sais urinários. Não está claro se as águas minerais naturais comercialmente disponíveis também é benéfica. OBJETIVO. Divulgar as informações sobre as características químicas e físico-químicas de águas minerais naturais de algumas das diversas fontes brasileiras. Essas informações serão de utilidade na análise de protocolos de pesquisa e na orientação do paciente. MÉTODOS. Foi feito uma coletânea das informações que constam nos rótulos de garrafas de águas minerais naturais, predominantemente não-gasosas, acessíveis ao consumo carioca. A partir da composição salina provável, foi calculada a concentração iônica de cada mineral. RESULTADOS. Foram estudadas as informações de 36 fontes situadas em alguns estados brasileiros. O pH, a 25oC, variou de 4,1 a 9,3 na dependência da fonte e foi linearmente correlacionado com as concentrações dos cátions cálcio, magnésio, sódio e do anion bicarbonato. Isto foi atribuído à alta alcalinidade desses sais, que contêm cerca de 70% de bicarbonato na molécula. Os teores de cálcio (0,3 a 42 mg/l, de magnésio (0,0 a 18 mg/l e de bicarbonato (4 a 228 mg/l foram considerados relativamente baixos. CONCLUSÃO. O teor mineral das fontes brasileiras que compuseram esse levantamento é baixo, com cerca de 70% delas apresentando teores de cálcio e de magnésio abaixo de 10 mg/l e 1 mg/l, respectivamente, semelhantes ao da água tratada da torneira.PURPOSE. To divulge information on the chemical composition and physical-chemical features of some mineral waters from Brazilian natural sources that will be of useful protocol in vestigation and patient advice. METHODS. The survey was based on bottle labels of non

Determination of thermotolerant coliforms present in coconut water produced and bottled in the Northeast of Brazil

Directory of Open Access Journals (Sweden)

Vandbergue Santos Pereira

2017-10-01

Full Text Available Abstract Coconut water is considered to be a natural isotonic drink and its marketing is gradually increasing. The objective of the present study was to evaluate the microbiological quality of the coconut water produced and bottled in the Northeast of Brazil. Products form ten industries from different states in the Northeast of Brazil were analyzed. The most probable number (MPN method was used to quantify the coliforms. Samples showing positive for coliforms were seeded on ChromAgar Orient plates and the bacteria identified from isolated colonies using the automated system Vitek 2 (BioMérieux, according to the manufacturer's instructions for the preparation of the inoculum, incubation, reading and interpretation. The samples showed thermotolerant coliform counts between 6.0×102 and 2.6×104 MPN/100 mL. The presence of Klebsiella pneumoniae, Morganella morganii and Providencia alcalifaciens was observed. The implementation of preventive methods and monitoring of the water quality by the industries is required.

Mineralization of hormones in breeder and broiler litters at different water potentials and temperatures.

Science.gov (United States)

Hemmings, Sarah N J; Hartel, Peter G

2006-01-01

When poultry litter is landspread, steroidal hormones present in the litter may reach surface waters, where they may have undesirable biological effects. In a laboratory study, we determined the mineralization of [4-14C]-labeled 17beta-estradiol, estrone, and testosterone in breeder litter at three different water potentials (-56, -24, and -12 MPa) and temperatures (25, 35, and 45 degrees C), and in broiler litter at two different water potentials (-24 and -12 MPa) and temperatures (25 and 35 degrees C). Mineralization was similar in both litters and generally increased with increasing water content and decreasing temperature. After 23 wk at -24 MPa, an average of 27, 11, and litter was mineralized to 14CO2 at 25, 35, and 45 degrees C, respectively. In contrast, mineralization of the radiolabeled estradiol and estrone was mineralized. The minimal mineralization suggests that the litters may still be potential sources of hormones to surface and subsurface waters.

Natural radioactivity in hot and mineral waters in Syria

International Nuclear Information System (INIS)

Othman, I.; Abbass, M.; Kattan, Z.

1994-08-01

A study of water chemistry and radioactivity of hot and mineral ground waters was conducted in Syria in order to determine the natural radioactivity levels as well as the mobility process of major radionuclides in the studied systems. The water samples were collected generally from carbonate and basaltic aquifer systems. The chemistry of groundwaters was a reflection of the rock type, while no relationship was found between the radionuclide activities and water temperatures. The increase of 222 Rn concentration in hot and mineral waters was accompanied by a similar increase of the concentration of its patent radionuclides (U t ot and 226 Ra). In parallel, the relative increase of 222 Rn concentration was correlated significantly with the presence of the large faults systems prevailing in the studied areas (Palmyrides and Great African Faults Systems). In all the cases, the radionuclide activity levels were below the maximum contaminant levels given for drinking water and health effects. (author). 11 refs., 7 figs., 8 tabs

Water physics and chemistry data from moored current meter and bottle casts in the Coastal Waters of New Jersey as part of the Mesa New York Bight (MESA - NYB) project, 1975-01-15 to 1975-12-08 (NODC Accession 7700136)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected using moored current meter and bottle casts in the Coastal Waters of New Jersey from January 15, 1975 to December 8,...

Formation of secondary minerals in a lysimeter approach - A mineral-microbe interaction

Science.gov (United States)

Schäffner, F.; Merten, D.; De Giudici, G.; Beyer, A.; Akob, D. M.; Ricci, P. C.; Küsel, K.; Büchel, G.

2012-04-01

Heavy metal contamination of large areas due to uranium mining operations poses a serious long-term environmental problem. In the Ronneburg district (eastern Thuringia, Germany), leaching of low grade uranium bearing ores (uranium content metals, especially Cd, Ni, Co, Cu and Zn due to a residual contamination even after remediation efforts. To reveal the processes of secondary mineral precipitation in the field a laboratory lysimeter approach was set up under in situ-like conditions. Homogenized soil from the field site and pure quartz sand were used as substrates. In general, in situ measurements of redox potentials in the substrates showed highly oxidizing conditions (200-750 mV). Water was supplied to the lysimeter from below via a mariottés bottle containing contaminated groundwater from the field. Evaporation processes were allowed, providing a continuous flow of water. This led to precipitation of epsomite and probably aplowite on the top layer of substrate, similar to what is observed in field investigations. After 4 weeks, the first iron and manganese bearing secondary minerals became visible. Soil water samples were used to monitor the behaviour of metals within the lysimeter. Saturation indices (SI) for different secondary minerals were calculated with PHREEQC. The SI of goethite showed oversaturation with respect to the soil solution. SEM-EDX analyses and IR spectroscopy confirmed the formation of goethite. Geochemical data revealed that goethite formation was mainly dominated by Eh/pH processes and that heavy metals, e.g. Zn and U, could be enriched in this phase. Although Eh/pH data does not support formation of manganese minerals, Mn(II)-oxidizing bacteria (MOB) could be isolated from field soil samples, supporting the fact that microorganisms may influence this natural attenuation process. Laser ablation ICP-MS data reveal accumulation of manganese in MOB biomass on Mn(II)-containing agar plates. Furthermore, it was possible to show the importance

Physical, chemical, and other data collected using moored bottle casts at the Coastal waters of California from 01 August 1999 to 01 October 1999 (NODC Accession 0000220)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Temperature, salinity, physical, chemical, and other data were collected using moored bottle casts in the Coastal Waters of California from the SAMPSON from August...

Water physics and chemistry data from moored current meter and bottle casts in the Coastal Waters of New Jersey as part of the Mesa New York Bight (MESA - NYB) project, 1974-03-08 to 1974-05-13 (NODC Accession 7501210)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected using moored current meter and bottle casts in the Coastal Waters of New Jersey from March 8, 1974 to May 13, 1974....

Water physics and chemistry data from moored current meter and bottle casts in the Coastal Waters of New Jersey as part of the Mesa New York Bight (MESA - NYB) project, 1963-05-21 to 1975-07-08 (NODC Accession 7601561)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected using moored current meter and bottle casts in the Coastal Waters of New Jersey from May 21, 1963 to July 8, 1975....

Isotopic investigations of mineral waters from Someseni - Cluj, Romania

International Nuclear Information System (INIS)

Cuna, Stela; Berdea, Petre; Baciu, Calin

2001-01-01

The Someseni mineral water spring area is located in the eastern part of Cluj-Napoca city, Romania, at the base of the first alluvial terrace of the Somesul Mic River. The presence of waters with therapeutical qualities in this area is known since the early 1920's. Only five springs are active at this moment. From a geological point of view, the mineral aquifer is located on the western border of the Neogene Transylvanian Basin. The Someseni spring area is situated in the axial zone of an anticline with salt core. Marls, with frequent intercalations of sandstones and volcanic tuffs dominate the lithology of these deposits. We have studied the flows of these waters by means of the hydrogen and oxygen isotopes. The method for determining the oxygen isotope composition was by equilibration with CO 2 and measurement of the isotopic ratio of CO 2 . Hydrogen isotope analysis of these waters was carried out on the hydrogen gas obtained by quantitative reduction of water directly in the inlet system of the mass spectrometer. In the interpretation of other authors, there are two distinct circuits of the waters from Someseni: a deep one, which determines a higher mineralisation, the water being in contact for a longer time with the salt massif, and a shallow one, located in alluvial deposits, which have a slight contact with the salt, reflected by its lower mineralisation. In our opinion, there is a single circuit for these mineral waters. The infiltration occurs through previous layers (volcanic tuffs, sandstones) in an unidentified recharging zone, generating a confined aquifer. This assumption can be sustained by the hydrogen and oxygen isotopes uptake of these waters. (authors)

Draft environmental impact report. California Department of Water Resources, Bottle Rock geothermal power plant, Lake County, CA

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

The California Department of Water Resources (DWR) proposes to construct the Bottle Rock power plant, a 55 MW geothermal power plant, at The Geysers Known Geothermal Resource Area (KGRA). The plant is projected to begin operation in April of 1983, and will be located in Lake County near the Sonoma County line on approximately 7.2 acres of the Francisco leasehold. The steam to operate the power plant, approximately 1,000,000 pounds/h, will be provided by McCulloch Geothermal Corporation. The power plant's appearance and operation will be basically the same as the units in operation or under construction in the KGRA. The power plant and related facilities will consist of a 55 MW turbine generator, a 1.1 mile (1.81 km) long transmission line, a condensing system, cooling tower, electrical switchyard, gas storage facility, cistern, and an atmospheric emission control system. DWR plans to abate hydrogen sulfide (H/sub 2/S) emissions through the use of the Stretford Process which scrubs the H/sub 2/S from the condenser vent gas stream and catalytically oxides the gas to elemental sulfur. If the Stretford Process does not meet emission limitations, a secondary H/sub 2/S abatement system using hydrogen peroxide/iron catalyst is proposed. The Bottle Rock project and other existing and future geothermal projects in the KGRA may result in cumulative impacts to soils, biological resources, water quality, geothermal steam resources, air quality, public health, land use, recreation, cultural resources, and aesthetics.

Molecular dynamics of interfacial water and cations associated with clay minerals

International Nuclear Information System (INIS)

Cygan, Randall T.; Greathouse, Jeffery A.; Teich-McGoldrick, Stephanie L.; Nenoff, Tina M.; Daemen, Luke L.

2012-01-01

Document available in extended abstract form only. Clay mineral interfaces, including interlayer and external surfaces, play an essential role in many geochemical processes. Adsorption, dissolution, precipitation, nucleation, and growth mechanisms, in particular, are controlled by the interplay of structure, thermodynamics, kinetics, and transport at clay mineral-water interfaces. Molecular details of these geochemical processes are especially important in evaluating the fate of radionuclide waste in the environment. Such details are typically beyond the sensitivity of experimental and analytical methods and therefore require accurate models and simulations. Also, the basal surfaces and interlayers of clay minerals offer structurally constrained interfacial environments to better evaluate the local molecular chemistry. We have developed and used classical and quantum methods to examine the complex behavior of clay mineral-water interfaces and dynamics of interlayer species. Bulk structures, swelling behavior, diffusion, and adsorption processes are evaluated and compared to experimental and spectroscopic findings. In particular, inelastic neutron scattering methods provide a successful probe of vibrational behavior of interlayer species to help guide the simulations. Librations involving rock, wag, and twist motions of water molecules are particularly sensitive to the interlayer environment of smectite minerals such as montmorillonite and beidellite. Trends in librational modes for interlayer water as a function of clay structure and cation hydration energy are readily explained using structural and vibrational analysis derived from molecular simulation. Molecular dynamics simulations of virtual phases, including hydrated pyrophyllite, help to explain the behavior of interlayer water that is not associated with cation species. Additionally, we use large-scale molecular dynamics simulations of other layered minerals, such as muscovite, to evaluate adsorption

Lithium content in potable water, surface water, ground water, and mineral water on the territory of Republic of Macedonia

OpenAIRE

Kostik, Vesna; Bauer, Biljana; Kavrakovski, Zoran

2014-01-01

The aim of this study was to determine lithium concentration in potable water, surface water, ground, and mineral water on the territory of the Republic of Macedonia. Water samples were collected from water bodies such as multiple public water supply systems located in 13 cities, wells boreholes located in 12 areas, lakes and rivers located in three different areas. Determination of lithium concentration in potable water, surface water was performed by the technique of inductively coupl...

Oxygen isotopic composition of sulphates from some mineral waters and mine waters in western Bohemia

International Nuclear Information System (INIS)

Smejkal, V.

1979-01-01

Two main genetic types of sulphate can be distinguished according to the delta 18 O(SO 4 2- ) measurements in sulphate-rich mineral and mine waters of western Bohemia - sulphates in descending mine waters and in weathered outcrops of graphitic pyrite slates from areas outside Tertiary basins, which originated in recent time by the oxidation of sulphides in the presence of atmospheric oxygen, have delta 18 O values from -2.1 to -6.1 per mille SMOW; and sulphates from springs of mineral waters of the renowned spas of Karlovy Vary, Frantiskovy Lazne and Marianske Lazne show distinctly heavier delta 18 O values - from +4.0 to +6.4 per mille, with maximum of values between +5.0 and +6.0 per mille. Similar delta 18 O values have been established in thenardites and in gypsum in Miocene claystones and in sulphates of some mine waters in the nearby Tertiary Cheb and Sokolov Basins. The presented results indicate that sulphates in mineral waters of the Karlovy Vary type originate mainly by leaching of Miocene sulphates and not by present-day oxidation of sulphidic sulphur. (author)

Mineralizing urban net-zero water treatment: Field experience for energy-positive water management.

Science.gov (United States)

Wu, Tingting; Englehardt, James D

2016-12-01

An urban net-zero water treatment system, designed for energy-positive water management, 100% recycle of comingled black/grey water to drinking water standards, and mineralization of hormones and other organics, without production of concentrate, was constructed and operated for two years, serving an occupied four-bedroom, four-bath university residence hall apartment. The system comprised septic tank, denitrifying membrane bioreactor (MBR), iron-mediated aeration (IMA) reactor, vacuum ultrafilter, and peroxone or UV/H 2 O 2 advanced oxidation, with 14% rainwater make-up and concomitant discharge of 14% of treated water (ultimately for reuse in irrigation). Chemical oxygen demand was reduced to 12.9 ± 3.7 mg/L by MBR and further decreased to below the detection limit (treatment. The process produced a mineral water meeting 115 of 115 Florida drinking water standards that, after 10 months of recycle operation with ∼14% rainwater make-up, had a total dissolved solids of ∼500 mg/L, pH 7.8 ± 0.4, turbidity 0.12 ± 0.06 NTU, and NO 3 -N concentration 3.0 ± 1.0 mg/L. None of 97 hormones, personal care products, and pharmaceuticals analyzed were detected in the product water. For a typical single-home system with full occupancy, sludge pumping is projected on a 12-24 month cycle. Operational aspects, including disinfection requirements, pH evolution through the process, mineral control, advanced oxidation by-products, and applicability of point-of-use filters, are discussed. A distributed, peroxone-based NZW management system is projected to save more energy than is consumed in treatment, due largely to retention of wastewater thermal energy. Recommendations regarding design and operation are offered. Copyright © 2016 Elsevier Ltd. All rights reserved.

Brucella detection in blood: comparison of the BacT/Alert standard aerobic bottle, BacT/Alert FAN aerobic bottle and BacT/Alert enhanced FAN aerobic bottle in simulated blood culture.

Science.gov (United States)

Sümerkan, B; Gökahmetoglu, S; Esel, D

2001-07-01

The objective of this study was to compare the performances of the standard aerobic bottle (StAe), FAN aerobic (FANAe) and enhanced FAN aerobic (E-FANAe) (the charcoal component of the FANAe was revised recently to improve the feasibility of Gram smear interpretation) blood culture bottles for BacT/Alert system for the detection of Brucella melitensis in simulated blood culture. Triplicate strains of eight clinical isolates of B. melitensis were studied. Each bottle was inoculated with 5 mL of freshly collected human blood at three different targeted bacterial inocula (10(1), 10(2) and 10(3) CFU/bottle). All bottles were monitored for up to 21 days or until they became positive. The results of time to detection (TTD) on the eight B. melitensis samples were as follows: at 10(1) CFU/bottle, the E-FANAe had a mean TTD significantly shorter than the StAe (48 h vs. 56.2 h, P StAe (41.2 h and 40 h vs. 45.6 h, P StAe, FANAe and E-FANAe were 96, 83 and 58%, respectively. At 10(3) CFU/bottle, the reproducibilities of StAe, FANAe and E-FANAe were 95, 95 and 91%, respectively. Positive results for the presence of bacteria in Gram smears were confirmed in 68% of StAe, 54% of FANAe and 90% of E-FANAe. In case of suspected brucellosis, the combination of one StAe bottle and one E-FANAe bottle seems to provide the highest and fastest recovery of the organism.

Study on heat transfer coefficients during cooling of PET bottles for food beverages

Science.gov (United States)

Liga, Antonio; Montesanto, Salvatore; Mannella, Gianluca A.; La Carrubba, Vincenzo; Brucato, Valerio; Cammalleri, Marco

2016-08-01

The heat transfer properties of different cooling systems dealing with Poly-Ethylene-Terephthalate (PET) bottles were investigated. The heat transfer coefficient (Ug) was measured in various fluid dynamic conditions. Cooling media were either air or water. It was shown that heat transfer coefficients are strongly affected by fluid dynamics conditions, and range from 10 W/m2 K to nearly 400 W/m2 K. PET bottle thickness effect on Ug was shown to become relevant under faster fluid dynamics regimes.

Water physics and chemistry data from moored current meter and bottle casts in the Coastal Waters of New Jersey as part of the Marine EcoSystems Analysis - New York Bight (MESA - NYB) project, 1973-08-27 to 1974-11-27 (NODC Accession 7600777)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected using moored current meter and bottle casts in the Coastal Waters of New Jersey from August 27, 1973 to November 7,...

Shipping container for a bottle of radioactive material

International Nuclear Information System (INIS)

Soldan, D.W.

1975-01-01

A shipping container for a bottle of radioactive material comprises a can having a cavity therein for receiving the bottle, a screw cap for the can and the cavity, and an annular bottle retainer extending downwardly in the cavity from its upper end having an outwardly extending flange at its upper end clamped between the cap and the upper end of the cavity and an inwardly extending flange at its lower end receiving the neck of the bottle. The cap carries a sponge to absorb spillage from the bottle. (U.S.)

Diagenetic and other highly mineralized waters in the Polish Carpathians

International Nuclear Information System (INIS)

Zuber, Andrzej; Chowaniec, Jozef

2009-01-01

Highly mineralized waters of different chemical types and origin occur in the flysch formations and their bedrocks in the western part of the Polish Carpathians. The marine sedimentation water of the flysch formations is not preserved, as the most mineralized and the heaviest isotopic values of flysch waters are characterized by δ 18 O and δ 2 H values in the ranges of 5-7 per mille and -(20-30) per mille , respectively. Their origin is related to the dehydration of clay minerals during burial diagenesis, with molecules of marine water completely removed by molecules of released bound water. They are relatively enriched in Na + in respect to the marine water, supposedly due to the release of Na + during the illitization of smectites and preferable incorporation of other cations from the primary brine into newly formed minerals. In some parts of younger formations, i.e. in the Badenian sediments, brines occur with isotopic composition close to SMOW and Cl - contents greatly exceeding the typical marine value of about 19.6 g/L, supposedly due to ultrafiltration. Most probably, the marine water of the flysch formations was similarly enriched chemically in its initial burial stages. Final Cl - contents in diagenetic waters depend on different Cl - contents in the primary brines and on relationships between diagenetic and further ultrafiltration processes. In some areas, diagenetic waters migrate to the surface along fault zones and mix with young local meteoric waters becoming diluted, with the isotope composition scattering along typical mixing lines. In areas with independent CO 2 flow from great depths, they form chloride CO 2 -rich waters. Common CO 2 -rich waters are formed in areas without near-surface occurrences of diagenetic waters. They change from the HCO 3 -Ca type for modern waters to HCO 3 -Mg-Ca, HCO 3 -Na-Ca and other types with elevated TDS, Mg 2+ and/or Na - contents for old waters reaching even those of glacial age. Bedrocks of the flysch are

Effects of Mineral Admixtures, Water Binder Ratio and Curing on ...

African Journals Online (AJOL)

Suitable addition of mineral admixtures like fly ash (FA), silica fume (SF), metakaolin (MK) etc., in concrete improves strength and durability characteristics of concrete. This paper presents the laboratory investigation on the effects of mineral admixtures and water binder ratio on compressive strength is discussed. The study ...

Green fiber bottle: Towards a sustainable package

DEFF Research Database (Denmark)

Didone, Mattia; Tosello, Guido; Howard, Thomas J.

The Green Fiber Bottle is a fully biodegradable bottle made from molded paper pulp.Its development depends on the establishment of the manufacturing technology. Impulse drying, an innovative way of drying, has the potential to improve significantly the manufacturing process of the Green Fiber Bot...... Bottle, towards a sustainable packaging...

The Consumption of Bicarbonate-Rich Mineral Water Improves Glycemic Control

Directory of Open Access Journals (Sweden)

Shinnosuke Murakami

2015-01-01

Full Text Available Hot spring water and natural mineral water have been therapeutically used to prevent or improve various diseases. Specifically, consumption of bicarbonate-rich mineral water (BMW has been reported to prevent or improve type 2 diabetes (T2D in humans. However, the molecular mechanisms of the beneficial effects behind mineral water consumption remain unclear. To elucidate the molecular level effects of BMW consumption on glycemic control, blood metabolome analysis and fecal microbiome analysis were applied to the BMW consumption test. During the study, 19 healthy volunteers drank 500 mL of commercially available tap water (TW or BMW daily. TW consumption periods and BMW consumption periods lasted for a week each and this cycle was repeated twice. Biochemical tests indicated that serum glycoalbumin levels, one of the indexes of glycemic controls, decreased significantly after BMW consumption. Metabolome analysis of blood samples revealed that 19 metabolites including glycolysis-related metabolites and 3 amino acids were significantly different between TW and BMW consumption periods. Additionally, microbiome analysis demonstrated that composition of lean-inducible bacteria was increased after BMW consumption. Our results suggested that consumption of BMW has the possible potential to prevent and/or improve T2D through the alterations of host metabolism and gut microbiota composition.

Development of technological modes for preparation of mineral water for sports drinks

Directory of Open Access Journals (Sweden)

I. Kovalenko

2015-05-01

Full Text Available Introduction. Conducted research study is devoted to development of technological modes of desalination of natural mineral medical-table sodium chloride water for water treatment technologies in the production of beverages for athletes. Materials and methods. Samples of initial water and water that has been desalinated using the experimental installation with different modes were investigated. Measuring of temperature mode of crystallizer was carried out using temperature sensors and digital thermometer. Quality indicators of the water samples using Photometer Palintest 7500 and standard techniques weredetermined. Resultsand discussion.The influence of different factors of the process of freezing on the quality of desalinated natural mineral medical-table sodium chloride water "Kuyalnik" was investigated. The patterns of distribution of components of initial water between the frozen solid phase, and a concentrated solution in the process of freezing are identified. For the majority of the investigated factors order of traffic was such: Ca 2+ >HCO -3 >(Na+>Cl- >(Mg2+>SO2-4 >K+, and with a decrease in water salinity so: Ca2+>SO2-4 >(Na+>Cl- >(HCO-3 >Mg2+>K+. Summary of the study results allowed to recommend the following technological parameters of the carrying out the process of desalination of natural mineral sodium chloride water by freeze: operating temperature mode of crystallizer, which is changing in the process from -2 to -4 ° C, the concentration of carbon dioxide in the water at the beginning of the process of freezing - 3,7 g/dm 3, duration of the desalination process (process without cooling - 60 minutes, one step of freezing, melting of solid phase under ambient conditions without prior separation of the frozen solid phase. With such technological modes of the carrying out the process of freezing it is possible to obtain water with mineral composition, mainly with existing relevant recommendations to the mineral composition of

Bottle appeal drifts across the Pacific

Science.gov (United States)

Ebbesmeyer, Curtis; Ingraham, W. James, Jr.; McKinnon, Richard; Okubo, Akira; Wang, Dong-Ping; Strickland, Richard; Willing, Peter

Pacific drift currents were used by a group of oceanographers to estimate the path of a drift bottle that was found on a beach of Barkley Sound in Vancouver Island by Richard Strickland on June 10, 1990. The Chinese rice wine bottle, which remained unopened until December 18, 1991, contained six leaflets, one appealing for the release of China's well-known dissident, Wei Jingsheng. The bottle was one of thousands set adrift as part of a propaganda effort from the islands of Quemoy and Matsu off mainland China shortly after Wei was sentenced in 1979 to 15 years in prison (see Figure 1 for locations). Wei was in poor health and still in prison when the bottle made its way across the Pacific Ocean.

Growth Performance, Mineral Digestibility, and Blood Characteristics of Ostriches Receiving Drinking Water Supplemented with Varying Levels of Chelated Trace Mineral Complex.

Science.gov (United States)

Seyfori, Hossein; Ghasemi, Hossein Ali; Hajkhodadadi, Iman; Nazaran, Mohammad Hassan; Hafizi, Maryam

2018-05-01

The effects of water supplementation of chelated trace minerals (CTM, which is named Bonzaplex designed with chelate compounds technology) on growth performance, apparent total tract digestibility (ATTD) of minerals, and some blood metabolites, TM, and antioxidant enzyme values in African ostriches were investigated from 8 to 12 months of age. A total of 20 8-month-old ostriches (five birds in five replicate pens) was randomly allocated into one of the following four treatments: (1) control (basal diet + tap water), (2) low CTM (basal diet +100 mg/bird/day CTM powder in tap water), (3) medium CTM (basal diet +1 g/bird/day CTM powder in tap water), and (4) high CTM (basal diet +2 g/bird/day CTM powder in tap water). Compared with control, medium CTM improved (P water can be recommended for improving growth performance, mineral absorption, and antioxidant status of ostriches fed diets containing the recommended levels of inorganic TM.

Management of PET plastic bottles waste through recycling Khartoum state

International Nuclear Information System (INIS)

Fadlalla, N. B. I.

2010-10-01

This study been carried out to assess the general waste management in Khartoum State and effectively manage the PET plastic bottles by identifying practical means and introducing recycling as cleaner production tool to achieve sustainable development goals. The information data were gathered during the period June-July 2010 through questionnaires, interview, meeting and visits to various sites, in addition to the official information and documents collected from reliable sources, mainly Sudan Central Bank, customs authorities, Ministry of Industry, soft drink and water bottling factories. The data were presented in tables, graphs and charts by applying windows excel program and also applying e view package for the future forecast. Analysis of data shows a rising consumption in PET bottles and the forecasted PET consumption in year 2015 estimated to be 60000 Tons, twice the estimate in the year 2010. This situation will create serious environmental problems that require much more effort to be exerted by all stake holders to book for scientific and practical solutions for the disposal of plastic waste through recycling. Based on the analysis and findings recommendations have been made that ensure on recycling of PET plastic bottles by mechanical method that depends mainly on collection, segregation, cleaning and processing. Further studies and researches on other recycling methods have been recommended in the future. (Author)

Mineral water 222 Rn activity decrease due to consumption habits

International Nuclear Information System (INIS)

Cipriani, Moacir; Taddei, Maria Helena Tirollo; Silva, Nivaldo Carlos da

2001-01-01

Mineral waters from the Pocos de Caldas Plateau springs, an elevated region with high natural radioactivity, in the State of Minas Gerais, Brazil, have significant 222 Rn concentration on site. The highest concentration in the waters are from: Fonte Villela - Aguas da Prata (∼ 1000 Bql -1 ); Fonte Grande Hotel - Pocinhos do Rio Verde (∼ 400 Brq -1 ) and Fonte CNEN Lab - Pocos de Caldas (∼ 290 Bql -1 ). These waters are used by the population as drinking water and due to consumption habits, can lead to internal doses above accepted limits for the public. This work deals with the decrease of 222 Rn activity in mineral waters fro two different popular consumption habits, and with the adult effective dose equivalent reduction due to water consumption habits. It has been found that the estimated dose based on the biokinetic Crawford-Brown model, can be one fourth of dose based on 222 Rn activity on site. (author)

Water physics and chemistry data from bottle casts from the AMIGO as part of the SEAGRANT project from 1972-01-19 to 1973-04-20 (NODC Accession 7400540)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Water physics and chemistry data were collected from bottle casts from the AMIGO from 19 January 1972 to 20 April 1973. Data were submitted by the Moss Landing...

Influence of UV radiation on the microflora of mineral waters mineralized differently

International Nuclear Information System (INIS)

Svorcova, L.

1981-01-01

The investigation was carried out on mineral waters with evaporation residues of 25 to 106 mg/l and 6300 to 6500 mg/l, resp., and turbidities up to 50 mg/l SiO 2 and numbers of germs up to 5 . 10 4 ml -1 . The parameters of the radiation device are: rate of water flow 2 to 7 l/min, radiation dosage 1.9 to 8.2 kWs/m 2 , wavelength 253.7 nm. As expected, the elimination performance with regard to the percent efficiency is dependent on the number of germs in the raw water, but the numbers of germs for the pseudomonades, mesophilic and gram-negative germs are always lower than 20/ml in clear raw water. Waters with turbidity values higher than 15 mg/l SiO 2 must be filtered prior to exposure. Iron and manganese bacteria are impaired only slightly, which leads to a rapid aftergrowth in the water. (author)

Diagenetic and other highly mineralized waters in the Polish Carpathians

Energy Technology Data Exchange (ETDEWEB)

Zuber, Andrzej, E-mail: andrzej.zuber@pgi.gov.pl [Polish Geological Institute, Carpathian Branch, PL-31560 Krakow, ul. Skrzatow 1 (Poland); Chowaniec, Jozef [Polish Geological Institute, Carpathian Branch, PL-31560 Krakow, ul. Skrzatow 1 (Poland)

2009-10-15

Highly mineralized waters of different chemical types and origin occur in the flysch formations and their bedrocks in the western part of the Polish Carpathians. The marine sedimentation water of the flysch formations is not preserved, as the most mineralized and the heaviest isotopic values of flysch waters are characterized by {delta}{sup 18}O and {delta}{sup 2}H values in the ranges of 5-7 per mille and -(20-30) per mille , respectively. Their origin is related to the dehydration of clay minerals during burial diagenesis, with molecules of marine water completely removed by molecules of released bound water. They are relatively enriched in Na{sup +} in respect to the marine water, supposedly due to the release of Na{sup +} during the illitization of smectites and preferable incorporation of other cations from the primary brine into newly formed minerals. In some parts of younger formations, i.e. in the Badenian sediments, brines occur with isotopic composition close to SMOW and Cl{sup -} contents greatly exceeding the typical marine value of about 19.6 g/L, supposedly due to ultrafiltration. Most probably, the marine water of the flysch formations was similarly enriched chemically in its initial burial stages. Final Cl{sup -} contents in diagenetic waters depend on different Cl{sup -} contents in the primary brines and on relationships between diagenetic and further ultrafiltration processes. In some areas, diagenetic waters migrate to the surface along fault zones and mix with young local meteoric waters becoming diluted, with the isotope composition scattering along typical mixing lines. In areas with independent CO{sub 2} flow from great depths, they form chloride CO{sub 2}-rich waters. Common CO{sub 2}-rich waters are formed in areas without near-surface occurrences of diagenetic waters. They change from the HCO{sub 3}-Ca type for modern waters to HCO{sub 3}-Mg-Ca, HCO{sub 3}-Na-Ca and other types with elevated TDS, Mg{sup 2+} and/or Na{sup -} contents for

Links between climate change, water-table depth, and water chemistry in a mineralized mountain watershed

Science.gov (United States)

Manning, Andrew H.; Verplanck, Philip L.; Caine, Jonathan S.; Todd, Andrew S.

2013-01-01

Recent studies suggest that climate change is causing rising solute concentrations in mountain lakes and streams. These changes may be more pronounced in mineralized watersheds due to the sensitivity of sulfide weathering to changes in subsurface oxygen transport. Specific causal mechanisms linking climate change and accelerated weathering rates have been proposed, but in general remain entirely hypothetical. For mineralized watersheds, a favored hypothesis is that falling water tables caused by declining recharge rates allow an increasing volume of sulfide-bearing rock to become exposed to air, thus oxygen. Here, we test the hypothesis that falling water tables are the primary cause of an increase in metals and SO4 (100-400%) observed since 1980 in the Upper Snake River (USR), Colorado. The USR drains an alpine watershed geologically and climatologically representative of many others in mineralized areas of the western U.S. Hydrologic and chemical data collected from 2005 to 2011 in a deep monitoring well (WP1) at the top of the USR watershed are utilized. During this period, both water table depths and groundwater SO4 concentrations have generally increased in the well. A numerical model was constructed using TOUGHREACT that simulates pyrite oxidation near WP1, including groundwater flow and oxygen transport in both saturated and unsaturated zones. The modeling suggests that a falling water table could produce an increase in metals and SO4 of a magnitude similar to that observed in the USR (up to 300%). Future water table declines may produce limited increases in sulfide weathering high in the watershed because of the water table dropping below the depth of oxygen penetration, but may continue to enhance sulfide weathering lower in the watershed where water tables are shallower. Advective air (oxygen) transport in the unsaturated zone caused by seasonally variable recharge and associated water table fluctuations was found to have little influence on pyrite

Method for strontium isolation from high-mineralized water

International Nuclear Information System (INIS)

Evzhanov, Kh.; Andriyasova, G.M.

1983-01-01

A method to isolate strontium from high-mineralized waters containing sodium, magnesium, calcium and strontium chlorides, which differ from the prototype method in a considerable decrease in energy consumption with the preservation of a high degree of Sr, Mg and Ca isolation selectivity, has been suggested. According to the method suggested mineralized waters are treated with alkali (NaOH) in the amount of 95-97% of stoichiometry by magnesium, then after separation of magnesium hydroxide precipitate mother liquor is treated with sodium carbonate in the amount of 50-60% of stoichiometry by calcium. After separation of calcium carbonate precipitate mother liquor is treated with NaOH in the amount of 130-135% of stoichiometry by calcium. After separation of calcium hydroxide precipitate from mother liquor by means of sodium carbonate introduction strontium carbonate is isolated. The degree of strontium extraction in the form of SrCO 3 constitutes 90.5% of its content in the initial solution. The method presented can be used for strontium separation from natural and waste waters

Bottled Water and Fluoride

Science.gov (United States)

... Private Wells Infant Formula Fluorosis Public Health Service Recommendation Water Operators & Engineers Water Fluoridation Additives Shortages of Fluoridation Additives Drinking Water Pipe Systems CDC-Sponsored Water Fluoridation Training Links to Other ...

27 CFR 24.308 - Bottled or packed wine record.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bottled or packed wine... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Records and Reports § 24.308 Bottled or packed wine record. A proprietor who bottles, packs, or receives bottled or packed beverage wine in bond shall...

Heat and mass transfer during the warming of a bottle of beer - doi: 10.4025/actascitechnol.v32i2.8273

Directory of Open Access Journals (Sweden)

Cláudio Vinicius Barbosa Monteiro

2010-07-01

Full Text Available The warming of a bottle of beer during a Friday evening happy hour directly involves transport phenomena, such as mass transfer due to condensation of air humidity on the bottle surface and heat transfer from the ambient to the bottle, which occurs by free convection and water condensation. Both processes happen simultaneously and are directly associated with the heat and mass transfer coefficients involved, which are affected by the ambient humidity and temperature. Several runs were made in several ambient conditions by exposing a cold bottle of beer to varied temperature and humidity and measuring the temperature of beer and the mass of water condensed on the bottle surface over time. From these measures, a theoretical and experimental methodology was developed and applied for the evaluation of the heat and mass transfer coefficients that govern this process. Both the relative humidity and ambient temperature exert a significant influence on the convective heat transfer coefficient. However, the mass transfer coefficient is affected only by the temperature.

1.3. Chemical and mineral additives of concretes and water used for concrete mix preparation

International Nuclear Information System (INIS)

Saidov, D.Kh.

2011-01-01

It is known that chemical and mineral additives increase physicochemical properties of concretes, thus, chemical and mineral additives, including super plasticizer and organo mineral additives are examined in this work. It was noted that along with salt water fresh water can also be used for concrete mix preparation.

Drinking Water Quality of Water Vending Machines in Parit Raja, Batu Pahat, Johor

Science.gov (United States)

Hashim, N. H.; Yusop, H. M.

2016-07-01

An increased in demand from the consumer due to their perceptions on tap water quality is identified as one of the major factor on why they are mentally prepared to pay for the price of the better quality drinking water. The thought that filtered water quality including that are commercially available in the market such as mineral and bottled drinking water and from the drinking water vending machine makes they highly confident on the level of hygiene, safety and the mineral content of this type of drinking water. This study was investigated the vended water quality from the drinking water vending machine in eight locations in Parit Raja are in terms of pH, total dissolve solids (TDS), turbidity, mineral content (chromium, arsenic, cadmium, lead and nickel), total organic carbon (TOC), pH, total colony-forming units (CFU) and total coliform. All experiments were conducted in one month duration in triplicate samples for each sampling event. The results indicated the TDS and all heavy metals in eight vended water machines in Parit Raja area were found to be below the Food Act 1983, Regulation 360C (Standard for Packaged Drinking Water and Vended water, 2012) and Malaysian Drinking Water Quality, Ministry of Health 1983. No coliform was presence in any of the vended water samples. pH was found to be slightly excess the limit provided while turbidity was found to be 45 to 95 times more higher than 0.1 NTU as required by the Malaysian Food Act Regulation. The data obtained in this study would suggest the important of routine maintenance and inspection of vended water provider in order to maintain a good quality, hygienic and safety level of vended water.

Interaction between Bisphosphonates and Mineral Water: Study of Oral Risedronate Absorption in Rats.

Science.gov (United States)

Itoh, Akihisa; Akagi, Yuuki; Shimomura, Hitoshi; Aoyama, Takao

2016-01-01

Bisphosphonates are antiosteoporotic agents prescribed for patients with osteoporosis. Drug package inserts for bisphosphonate supplements indicate that their bioavailability is reduced by high levels of metal cations (Ca(2+), Mg(2+), etc.). However, standards for these cations in water used for taking risedronate have not been defined. Here, we examined the effect of calcium and magnesium in mineral waters on the bioavailability of the third-generation bisphosphonate, risedronate, following oral administration in rats. As risedronate is unchanged and eliminated renally, risedronate absorption was estimated from the amount excreted in the urine. Risedronate was dissolved in mineral water samples and administered orally at 0.35 mg/kg. Urine samples were collected for 24 h after dosing. Risedronate was extracted from urine using ion-pair solid-phase cartridges and quantified by HPLC with UV detection (262 nm). Cumulative recovery of risedronate was calculated from the amount excreted in the urine. The 24-h recovery of risedronate from evian® (0.32±0.02% [mean±standard deviation (S.D.)], n=4) and Contrex(®) (0.22±0.05%) mineral waters was significantly lower than that from tap water (0.47±0.04%, pAbsorption of risedronate in calcium chloride and magnesium chloride aqueous solutions of the same hardness (822 mg/L) was 54% (0.27±0.04%) and 12% (0.51±0.08%) lower, respectively, compared with ultrapure water; suggesting that absorption of risedronate declines as the calcium concentration of mineral waters increases. Consumption of mineral waters containing high levels of calcium (80 mg/L or above), such as evian® and Contrex(®), is therefore not recommended when taking risedronate.

Microorganisms in the deposits of cold carbon mineral waters of the Russian Far East and their habitats

Science.gov (United States)

Kalitina, E. G.; Kharitonova, N. A.; Kuzmina, T. V.; Chelnokov, G. A.

2018-01-01

Study of the chemical composition of carbon mineral waters has shown the prevalence of calcium, magnesium and sodium among the cations, sulfate, nitrate and chloride ions among the anions, and ferric iron, strontium and manganese in the microelement composition. Results of the microbiological studies have revealed that carbon mineral waters contain various microorganisms that can transform the physical and chemical composition of mineral waters by interfering with geochemical cycles. The sanitary and microbiological properties of carbon mineral waters have been evaluated thus proving that the waters of Medvezhii (Shmakovskoe deposit) are microbiologically clean.

Origin of life and living matter in hot mineral water

OpenAIRE

Ignatov, Ignat; Mosin, Oleg

2013-01-01

In this review the composition of water and isotopic structure of water during a process of origin of life is submitted. The data obtained testify that life maintenance depends on physical-chemical properties of water and external factors – temperature and рН. Hot mineral alkaline water, which interacts with CaCO 3 is closest to these conditions. Next in line with regard to quality is sea and mountain water.

Zeta-potential and flotability of the scheelite mineral in different type of waters, Part 2: Flotability

Directory of Open Access Journals (Sweden)

Milanović Dragan B.

2009-01-01

Full Text Available The aim of this work was to study floatability of the mineral sheelite from mine 'Rudnik', central Serbia. Flotation tests of the mineral in a Hallimond tube cell were carried out in four different types of water, namely: tap water, distilled water, rain water and spring water. All types of water had different hardness and conductivity as well as natural pH values. It was found that the flotability of mineral scheelite depends on the hardness and electro-conductivity of the chosen type of water as well as on Ca2+ content. Also, it was found the floatability of mineral depends on the scheelite particle size fraction used in microflotation experiments. Presented results may be useful for proper selection of type of water, as well of the type of reagents used in flotation processes.

IMMOBILIZATION OF HEAVY METALS IN SOILS AND WATER BY A MANGANESE MINERAL

Science.gov (United States)

A synthesized Mn mineral used in study on adsorption of heavy metals from water has shown a great adsorption capability for Pb, Cu, Cd, Co, Ni and Zn on this mineral over a pH range from 2 to 8. The retention of Pb on this mineral was as high as 10% of its weight. Application of ...

[The marketing evaluation of the consumers' preference as regards the use of medicinal and medicinal table mineral waters].

Science.gov (United States)

Babaskin, D V; Babaskina, L I; Pavlova, A V

2017-12-28

The development of modern technologies in physiotherapy with the use of mineral waters, the expansion of the assortment of the medicinal and medicinal table waters as well as increasing the competitive advantages of domestic products require the more extensive marketing survey of the consumers' preferences in the market of mineral waters. The objective of the present study was the marketing evaluation of the consumers' preference in the segment of medicinal and medicinal table mineral waters in the city of Moscow. The survey involved 697 consumers of medicinal and medicinal table mineral waters. The sampling was carried out by the deterministic quota method. The field research was conducted by means of personal verbal interviews (32%) and the CATI to Web method (phone recruiting and on-line questioning) (68%) with the use of the structured questionnaire. Positioning was carried out making use of the two-dimensional schematic map and scoring assessment on an individual basis with calculation of integrated indicators. The marketing evaluation has demonstrated that the principal motive for purchasing mineral waters in more than 40% of respondents was the treatment and prevention of various diseases including disturbances in the urogenital system as well as digestive and respiratory disorders that appear to be the most frequent reasons for the consumption of mineral waters. The main factors that form the preferences of the consumers as regards the use of a concrete variety of mineral waters were elucidated. Of crucial importance for approximately 40% of the consumers (p<0.01) proved to be their health condition, the medical indications, and the available information about the therapeutic effectiveness of one or another type of mineral waters. Other factors were the quality of mineral water, its cost, the manufacturer and/or place of production, the attractiveness of the packaging, etc. The evaluation of the positioning of the mineral water consumers' preferences made

27 CFR 19.749 - Bottling and packaging record.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bottling and packaging record. 19.749 Section 19.749 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Account § 19.749 Bottling and packaging record. The bottling and packaging record shall be prepared and...

DEVELOPMENT OF RAPID TECHNIQUE FOR DETERMINATION OF THE TOTAL MINERALIZATION OF NATURAL WATERS

Directory of Open Access Journals (Sweden)

T. A. Kuchmenko

2015-01-01

Full Text Available A new approach has been proposed for rapid and easy evaluation of a indicator of quality and properties of natural water - soluble salt content (mineralization. The method of quartz crystal microbalance is employed at load of the mass-sensitive resonator electrode (BAW-type with investigated water. The degree of correlation between the various indicators related to the contents of salts and insoluble compounds and the level of mineralization obtained by the standard method (gravimetry has been studied. A procedure for salt weighing by single sensor at unilateral load with small sample of natural water has been developed. The optimal conditions for measurement is established using the design of experiment by model 23 . The possibilities of quartz crystal microbalance for determination of non-volatile compounds in the water are described. The calibration of piezosensor is produced by standard solution NaCl (c = 1.000 g / dm3 at optimal conditions of experiment. The adequacy and accuracy of proposed technique is assessed by the correlation between the results of quartz crystal microbalance and conductometry. The correlation between indicators of mineralization established by quartz crystal microbalance and gravimetry is found. It has been obtained an equation that can be used to calculate the standard indicator of the mineralization by the results of a quartz crystal microbalance using single sensor. The approaches to enhance the analytical capabilities of the developed technique for water with low and high mineralization are proposed. The metrological characteristics of quartz crystal microbalance of insoluble compounds in natural water are estimated. A new technique of determination of the mass concentration of the dry residue in water with a conductivity of 0.2 mS or above has been developed, which can be used for rapid analysis of the water at nonlaboratory conditions and in the laboratory for rapid obtaining the information about a sample.

RO unit for canned coffee drink processing line. Shipped to Tone Coca-Cola Bottling Co. Ltd., Ibaraki plant; Coffee line yo RO sochi. Tone Coca-Cola Bottling (kabu) Ibaraki kojo nonyu

Energy Technology Data Exchange (ETDEWEB)

Nakajima, K. [Ebara Corp., Tokyo (Japan)

1996-01-20

The paper introduces an RO unit (reverse osmotic membrane equipment) for producing water holding for the canned coffee drink processing line introduced to the Ibaraki plant of Tone Coca-Cola Bottling Co. The unit aims at reducing hardness components from city water and producing water holding for the coffee drink processing line. The capacity of the unit is 25m{sup 3}/h and the recovery rate is 80%. The unit is composed of a sand filter, an heat exchanger, a pre-filter, RO modules, a treated water tank, chemicals storage tanks, and an RO cleaning unit, which are all for pretreatment. The treated water, into which chlorine is injected, is sent through the existing activated carbon tower and micro filter to the processing line. The RO unit can remove at the same time ion and trihalomethane, pathogens, organic matters which are substances other than hardness components. The continued water bottling is possible with no need for the usual reproduction process, and the maintenance is easy. Because of the high hardness of the supplied raw water, acid is injected at the primary side of the unit for pH regulation to prevent scale deposition in the RO modules. The quality of the treated water well met the specifications. 2 figs., 2 tabs.

LOW WATER DEMAND CEMENTS - WAY OF EFFICIENT USE OF CLINKER AND MINERAL FILLERS IN CONCRETES

Directory of Open Access Journals (Sweden)

Khokhryakov Oleg Viktorovich

2017-10-01

Full Text Available Subject: the provisions in the updated edition of the technical specifications for cements are analyzed. A trend to decrease the clinker volume in Portland cement due to the wider use of mineral additives, up to 95%, was observed. Research objectives: substantiation of the most complete and efficient use of Portland cement and mineral additives in the composition of low water demand cements. Materials and methods: portland cement, mineral additives and superplasticizer were used as raw materials for obtaining cements of low water demand. The experimental methods comply with the current standards. Results: comparative properties of low water demand cements and cements with mineral additives are presented. The properties of cement-water suspensions of these binders have been studied, and, on their basis, heavy concretes have been made. The results of the grindability of Portland cement and mineral components with a superplasticizer are given. Conclusions: it is shown that the cement of low water demand, in which the advantages of both Portland cement and mineral additives are more fully and efficiently presented, complies with the tendency to decrease the clinker volume to the greatest degree. It is established that the clinker volume index for heavy concrete prepared on low water demand cement is almost four times lower than that for heavy concrete based on common Portland cement.

Ocular injuries from carbonated soft drink bottle explosions.

Science.gov (United States)

Al Salem, M; Sheriff, S M

1984-04-01

Sixteen cases of ocular injuries serious enough to require admission to Ibn-Sina Hospital, Kuwait, Arabian Gulf, due to explosion of glass bottles of carbonated soft drinks are reported over a period of 14 months from the beginning of July 1981 to the end of August 1982. Prevalence was much greater in the summer months and among children. Explosions of bottles without prior agitation occurred in 11 cases (68.7%). High environmental temperature and defective bottles were the most important predisposing factors. Preventive measures we suggest are better standards for manufacturers, more careful inspection of returnable bottles to detect defective ones, a separate detailed warning label on all bottles, and health education especially of school children about this and other risks of serious injury to the eyes and other parts of the body.

Heat and mass transfer during the warming of a bottle of beer - doi: 10.4025/actascitechnol.v32i2.8273

OpenAIRE

Monteiro, Cláudio Vinicius Barbosa; UEM; Righetto, Aderson Roberto; Universidade Estadual de Maringá; Souza, Leonardo César de; Universidade Estadual de Maringá; Paraíso, Paulo Roberto; UEM; Jorge, Luiz Mario de Matos; UEM

2010-01-01

The warming of a bottle of beer during a Friday evening happy hour directly involves transport phenomena, such as mass transfer due to condensation of air humidity on the bottle surface and heat transfer from the ambient to the bottle, which occurs by free convection and water condensation. Both processes happen simultaneously and are directly associated with the heat and mass transfer coefficients involved, which are affected by the ambient humidity and temperature. Several runs were made in...

Radioactivity in drinking water: regulations, monitoring results and radiation protection issues

Directory of Open Access Journals (Sweden)

Cristina Nuccetelli

2012-12-01

Full Text Available INTRODUCTION: Drinking waters usually contain several natural radionuclides: tritium, radon, radium, uranium isotopes, etc. Their concentrations vary widely since they depend on the nature of the aquifer, namely, the prevailing lithology and whether there is air in it or not. AIMS: In this work a broad overview of the radioactivity in drinking water is presented: national and international regulations, for limiting the presence of radioactivity in waters intended for human consumption; results of extensive campaigns for monitoring radioactivity in drinking waters, including mineral bottled waters, carried out throughout the world in recent years; a draft of guidelines for the planning of campaigns to measure radioactivity in drinking water proposed by the Environmental Protection Agency (ARPA of Lombardia.

Mineral waters of the Pannonian basin spas in the Republic of Serbia

Directory of Open Access Journals (Sweden)

Klimo Atila

2011-01-01

Full Text Available Introduction. The fact itself that thermo-mineral waters and mud have healing effects has always attracted attention throughout the history to exploit, explore and study their benefit on the human body. Modern lifestyle and the speed of life endanger man’s psycho-physical health. This is why people more often return to old time proven values, the nature and natural health resorts. Objective. To establish hydro-geological conditions for the formation of mineral water and to summarize their balneological characteristics in spas, i.e., in rehabilitation centres of the Pannonian basin of the Republic of Serbia, where underground waters are still actively exploited for balneotherapy. Methods. By retrospective descriptive analysis, a recapitulation of hydro-geological conditions for the formation of mineral waters was made and their balneological characteristics were established in eight spas of the Pannonian basin. Results. The healing spas of the Pannonian basin are predominated by HCO3 (2.9 g/l - 4.6% milival, iodic (up to 6.5 mg/l, slightly alkaline (pH up to 8.1 thermal-mineral water (temperature up to 72°C, bounty to 36.6 l/s with a significant content of Br (up to 8.1 mg/l, Fe (to 6.0 mg/l, metaboron (up to 60 mg/l and metasilicon acid (up to 95 mg/l. They are used for external application, bathing and showering. Conclusion. Once the Pannonian Sea (the Paratethys, today a wide plain terrain is a tectonic depression of the lower Pannonian pont age with compact type aquifers. In the geological column of sedimentary rocks a large underground aquifer was formed with free water of high mineralization, high temperature and geothermal properties above the average in relation to the European hydrogeological standards. Therefore, the Pannonian basin can be rightly called a thermal valley with the predominance of sodium hydro-carbonate (alkaline iodine healing water of enviable abundance and reserves.

[The effects of the combined use of mineral water with ascorbic acid and rutin experimentally and clinically].

Science.gov (United States)

Polushina, N D; Kartazaeva, V A; Botvineva, L A; Kozhevnikov, S A

2000-01-01

Effects of a single and course intake of glucose, ascorbic acid and rutin in combination with mineral water Essentuki N17 on blood levels of glucose, hydrocortisone, ACTH, insulin were studied in 336 Wistar male rats. 80 patients with diabetes mellitus type I and II received a course of ascorutin and mineral water. Mineral water proved able to reduce a hyperglycemic effect of vitamins. A course of mineral water and ascorutin promotes improvement of carbohydrate, lipid metabolism, elevates plasma content of ascorbic acid, diminishes the need in sugar-reducing drugs.

Determination of iron in natural and mineral waters by flame atomic absorption spectrometry

Directory of Open Access Journals (Sweden)

ROLANDAS KAZLAUSKAS

2004-05-01

Full Text Available Simple methods for the determination of Fe in natural and mineral waters by flame atomic absorption spectrometry (AAS are suggested. The results of the investigation of selectivity of the proposed AAS method proved that this procedure is not affected by high concentrations of other metals. The calibration graph for iron was linear at levels near the detection limit up to at least 0.10 mg ml-1. For the determination of microamounts of iron in mineral waters, an extraction AAS technique was developed. Iron was retained as Fe-8-oxyquinoline complex and extracted into chloroform. The optimal conditions for the extraction of the iron complex were determined. The AAS method was applied to the determination of Fe in mineral waters and natural waters from different areas of Lithuania. The accuracy of the developed method was sufficient and evaluated in comparison with a photometric method. The obtained results demonstrated that the procedure could be successfully applied for the analysis of water samples with satisfactory accuracy.

Effect of carbonated beverages, coffee, sports and high energy drinks, and bottled water on the in vitro erosion characteristics of dental enamel.

Science.gov (United States)

Kitchens, Michael; Owens, Barry M

2007-01-01

This study evaluated the effect of carbonated and non-carbonated beverages, bottled and tap water, on the erosive potential of dental enamel with and without fluoride varnish protection. Beverages used in this study included: Coca Cola Classic, Diet Coke, Gatorade sports drink, Red Bull high-energy drink, Starbucks Frappuccino coffee drink, Dasani water (bottled), and tap water (control). Enamel surfaces were coated with Cavity Shield 5% sodium fluoride treatment varnish. Twenty-eight previously extracted human posterior teeth free of hypocalcification and caries were used in this study. The coronal portion of each tooth was removed and then sectioned transverse from the buccal to lingual surface using a diamond coated saw blade. The crown sections were embedded in acrylic resin blocks leaving the enamel surfaces exposed. The enamel surfaces were polished using 600 to 2000 grit abrasive paper and diamond paste. Test specimens were randomly distributed to seven beverage groups and comprised 4 specimens per group. Two specimens per beverage group were treated with a fluoride varnish while 2 specimens did not receive fluoride coating. Surface roughness (profilometer) readings were performed at baseline (prior to fluoride treatment and immersion in the beverage) and again, following immersion for 14 days (24 hours/day). The test beverages were changed daily and the enamel specimens were immersed at 37 degrees C. Surface roughness data was evaluated using multiple factor ANOVA at a significance level of pStarBucks coffee, Dasani water, and tap water. Fluoride varnish was not a significant impact factor; however, beverage (type) and exposure time were significant impact variables. Both carbonated and non-carbonated beverages displayed a significant erosive effect on dental enamel; however, fluoride varnish treatments did not demonstrate a significant protective influence on enamel surfaces.

Arsenic mobilization and attenuation by mineral-water interactions: implications for managed aquifer recharge.

Science.gov (United States)

Neil, Chelsea W; Yang, Y Jeffrey; Jun, Young-Shin

2012-07-01

Managed aquifer recharge (MAR) has potential for addressing deficits in water supplies worldwide. It is also widely used for preventing saltwater intrusion, maintaining the groundwater table, and augmenting ecological stream flows, among many other beneficial environmental applications. However, field MAR sites have experienced arsenic mobilization from aquifer formation minerals due to induced changes in groundwater chemistry. To address this environmental concern, it is crucial to understand the potential sources and sinks impacting arsenic mobilization. This paper outlines important mineral-water interactions that can occur at MAR sites. Detailed information on minerals of concern, physiochemical processes for arsenic mobilization or attenuation, and the potential impact of microbial activity and hydrology on these processes is provided. Based on these mineral-water interactions, guidelines for predicting arsenic mobility are presented, and recommendations are made concerning MAR site monitoring. The review emphasizes important aspects in correlating interfacial reactions to reactive transport modeling and elucidating future challenges, a first step toward developing safer and more sustainable MAR operations.

Calcium Bioavailability from Mineral Waters with Different Mineralization in Comparison to Milk and a Supplement.

Science.gov (United States)

Greupner, Theresa; Schneider, Inga; Hahn, Andreas

2017-07-01

The aim of the present study was to compare the bioavailability of calcium from 3 mineral waters with different concentrations of minerals with that of milk and a calcium supplement. A single-center, randomized controlled trial with a crossover design with 21 healthy men and women was conducted at the Institute of Food Science and Human Nutrition, Leibniz University Hannover. The participants consumed the 5 test products providing 300 mg of calcium each on 5 examination days with 1-week wash-out phases in between. Primary outcome variables were the area under the curve of serum calcium levels for 10-hour (AUC 0-10h ) and 24-hour urinary calcium excretion. In all groups, no significant differences in the AUC 0-10h of serum calcium levels as well as in the 24-hour urinary calcium excretion were observed. Likewise, mean changes in serum phosphate and urinary phosphate, as well as serum parathormone, showed no differences between the groups. Given an equivalent bioavailability of calcium in all test products, neither a high concentration of SO 4 2- or of HCO 3 influenced the bioavailability of calcium. Accordingly, the use of mineral water with high concentrations of calcium constitutes a calorie-free calcium source that can improve calcium supply.

UTILIZATION OF WASTE PLASTIC BOTTLES IN ASPHALT MIXTURE

Directory of Open Access Journals (Sweden)

TAHER BAGHAEE MOGHADDAM

2013-06-01

Full Text Available Nowadays, large amounts of waste materials are being produced in the world. One of the waste materials is plastic bottle. Generating disposable plastic bottles is becoming a major problem in many countries. Using waste plastic as a secondary material in construction projects would be a solution to overcome the crisis of producing large amount of waste plastics in one hand and improving the structure’s characteristics such as resistance against cracking on the other hand. This study aimed to investigate the effects of adding plastic bottles in road pavement. Marshall properties as well as specific gravity of asphalt mixture containing different percentages of plastic bottles were evaluated. Besides, Optimum Asphalt Content (OAC was calculated for each percentages of plastic bottles used in the mix. The stiffness and fatigue characteristics of mixture were assessed at OAC value. Results showed that the stability and flow values of asphalt mixture increased by adding waste crushed plastic bottle into the asphalt mixture. Further, it was shown that the bulk specific gravity and stiffness of mixtures increased by adding lower amount of plastic bottles; however, adding higher amounts of plastic resulted in lower specific gravity and mix stiffness. In addition, it was concluded that the mixtures containing waste plastic bottles have lower OAC values compared to the conventional mixture, and this may reduce the amount of asphalt binder can be used in road construction projects. Besides, the mixtures containing waste plastic showed significantly greater fatigue resistance than the conventional mixture.

Eliminating Heavy Metals from Water with NanoSheet Minerals as Adsorbents

Directory of Open Access Journals (Sweden)

Shaoxian Song

2017-12-01

Full Text Available Heavy metals usually referred to those with atomic weights ranging from 63.5 to 200.6. Because of natural-mineral dissolution and human activities such as mining, pesticides, fertilizer, metal planting and batteries manufacture, etc., these heavy metals, including zinc, copper, mercury, lead, cadmium and chromium have been excessively released into water courses, like underground water, lake and river, etc. The ingestion of the heavy metals-contaminated water would raise serious health problems to human beings even at a low concentration. For instance, lead can bring human beings about barrier to the normal function of kidney, liver and reproductive system, while zinc can cause stomach cramps, skin irritations, vomiting and anemia. Mercury is a horrible neurotoxin that may result in damages to the central nervous system, dysfunction of pulmonary and kidney, chest and dyspnea. Chromium (VI has been proved can cause many diseases ranging from general skin irritation to severe lung carcinoma. Accordingly, the World Health Organization announced the maximum contaminant levels (MCL for the heavy metals in drinking water. There are numerous processes for eliminating heavy metals from water in order to provide citizens safe drinking water, including precipitation, adsorption, ion exchange, membrane separation and biological treatment, etc. Adsorption is considered as a potential process for deeply removing heavy metals, in which the selection of adsorbents plays a predominant role. Nano-sheet minerals as the adsorbents are currently the hottest researches in the field. They are obtained from layered minerals, such as montmorillonite, graphite and molybdenite, through the processing of intercalation, electrochemical and mechanical exfoliation, etc. Nano-sheet minerals are featured by their large specific surface area, relatively low costs and active adsorbing sites, leading to be effective and potential adsorbents for heavy metals removal from water

27 CFR 31.232 - Wine bottling.

Science.gov (United States)