WorldWideScience

Sample records for mg yield rich

  1. Preparation and Hydrogen Storage Properties of Mg-Rich Mg-Ni Ultrafine Particles

    Directory of Open Access Journals (Sweden)

    Jianxin Zou

    2012-01-01

    Full Text Available In the present work, Mg-rich Mg-Ni ultrafine powders were prepared through an arc plasma method. The phase components, microstructure, and hydrogen storage properties of the powders were carefully investigated. It is found that Mg2Ni and MgNi2 could be obtained directly from the vapor state reactions between Mg and Ni, depending on the local vapor content in the reaction chamber. A nanostructured MgH2 + Mg2NiH4 hydrogen storage composite could be generated after hydrogenation of the Mg-Ni ultrafine powders. After dehydrogenation, MgH2 and Mg2NiH4 decomposed into nanograined Mg and Mg2Ni, respectively. Thermogravimetry/differential scanning calorimetry (TG/DSC analyses showed that Mg2NiH4 phase may play a catalytic role in the dehydriding process of the hydrogenated Mg ultrafine particles.

  2. Microstructural evolution in Mg-rich Mg-Zn-Y alloys

    International Nuclear Information System (INIS)

    Biswas, T.; Ranganathan, S.; Nair, S.; Bajargan, G.

    2005-01-01

    Mg-rich Mg-Zn-Y alloys with nominal compositions Mg 97 Zn 1 Y 2 , Mg 97 Zn 2 Y 1 , Mg 92 Zn 6.5 Y 1.5 and Mg 97-x Zn 1 Y 2 Zr x have been chosen for the present study. These alloys are prepared by using sand casting mold. The sand cast alloys are remelted and subjected to copper mold casting and melt spinning techniques. The effect of cooling rate on microstructures was studied. It is observed that the size of the precipitates decreases with an increase of cooling rate. The formation of nano precipitates results in higher strength of the alloy as compared to the conventional alloys. The microstructures of melt spun ribbons are compared with RS/PM (rapidly solidified power metallurgy) Mg 97 Zn 1 Y 2 alloy, obtained from a different source. (author)

  3. The study of a Mg-rich epoxy primer for protection of AZ91D magnesium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Lu Xiangyu [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zuo Yu, E-mail: zuoy@mail.buct.edu.c [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zhao Xuhui; Tang Yuming; Feng Xingguo [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

    2011-01-15

    Research highlights: {yields} A Mg-rich epoxy primer was prepared by adding pure magnesium particles in epoxy coating. Cross scratch testing results showed that in 3% NaCl solution the Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. {yields} The open circuit potential of AZ91D alloy in NaCl solution decreased after coated with Mg-rich coating, suggesting that cathodic protection effect of the Mg-rich coating on AZ91D alloy was present. {yields} EIS studies showed that during the immersion tests of AZ91D alloy with Mg-rich coating the magnesium particles in coating dissolved with the charge-transfer resistance R{sub ct} at the magnesium particle/coating interface decreased and the double-layer capacitance Q{sub dl} increased. While the coating resistance remained stable for a long time and corrosion of the AZ91D alloy substrate was obviously delayed. - Abstract: A Mg-rich epoxy primer was prepared by adding pure magnesium particles to an epoxy coating. The coating properties were studied with electrochemical impedance spectroscopy (EIS), scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. The open circuit potential measurements showed cathodic protection effect of the Mg-rich primer on AZ91D alloy. Cross scratch testing showed that the Mg-rich primer provided better protection for the substrate than original epoxy coating. The precipitation of Mg(OH){sub 2} in the coating also provided some degree of barrier protection.

  4. Non-Equilibrium Heavy Flavored Hadron Yields from Chemical Equilibrium Strangeness-Rich QGP

    OpenAIRE

    Kuznetsova, Inga; Rafelski, Johann

    2008-01-01

    The yields of heavy flavored hadrons emitted from strangeness-rich QGP are evaluated within chemical non-equilibrium statistical hadronization model, conserving strangeness, charm, and entropy yields at hadronization.

  5. Magnesium-Based Sacrificial Anode Cathodic Protection Coatings (Mg-Rich Primers for Aluminum Alloys

    Directory of Open Access Journals (Sweden)

    Michael D. Blanton

    2012-09-01

    Full Text Available Magnesium is electrochemically the most active metal employed in common structural alloys of iron and aluminum. Mg is widely used as a sacrificial anode to provide cathodic protection of underground and undersea metallic structures, ships, submarines, bridges, decks, aircraft and ground transportation systems. Following the same principle of utilizing Mg characteristics in engineering advantages in a decade-long successful R&D effort, Mg powder is now employed in organic coatings (termed as Mg-rich primers as a sacrificial anode pigment to protect aerospace grade aluminum alloys against corrosion. Mg-rich primers have performed very well on aluminum alloys when compared against the current chromate standard, but the carcinogenic chromate-based coatings/pretreatments are being widely used by the Department of Defense (DoD to protect its infrastructure and fleets against corrosion damage. Factors such as reactivity of Mg particles in the coating matrix during exposure to aggressive corrosion environments, interaction of atmospheric gases with Mg particles and the impact of Mg dissolution, increases in pH and hydrogen gas liberation at coating-metal interface, and primer adhesion need to be considered for further development of Mg-rich primer technology.

  6. Radio Telescopes' Precise Measurements Yield Rich Scientific Payoffs

    Science.gov (United States)

    2008-01-01

    Having the sharpest pictures always is a big advantage, and a sophisticated radio-astronomy technique using continent-wide and even intercontinental arrays of telescopes is yielding extremely valuable scientific results in a wide range of specialties. That's the message delivered to the American Astronomical Society's meeting in Austin, Texas, by Mark Reid of the Harvard-Smithsonian Center for Astrophysics, a leading researcher in the field of ultra-precise astronomical position measurements. Very Long Baseline Interferometry provides extremely high precision that can extend use of the parallax technique to many more celestial objects. Parallax is a direct means of measuring cosmic distances by detecting the slight shift in an object’s apparent position in the sky caused by Earth’s orbital motion. Credit: Bill Saxton, NRAO/AUI/NSF "Using radio telescopes, we are measuring distances and motions of celestial bodies with unprecedented accuracy. That's helping us better understand many processes ranging from star formation to the scale of the entire Universe," Reid said. The observing technique, called Very Long Baseline Interferometry (VLBI), was pioneered in 1967, but has come into continuous use only in the past 10-15 years. The National Science Foundation's Very Long Baseline Array (VLBA), a system of 10 radio-telescope antennas ranging from Hawaii to the Caribbean, was dedicated in 1993. There are other VLBI systems in Europe and Asia, and large radio telescopes around the world cooperate regularly to increase sensitivity. VLBI observations routinely produce images hundreds of times more detailed than those made at visible-light wavelengths by the Hubble Space Telescope. Several groups of researchers from across the globe use the VLBA to study stellar nurseries in our own Milky Way Galaxy and measure distances to regions where new stars are forming. The key has been to improve measurement accuracy to a factor of a hundred times better than that produced by the

  7. Compositional and structural variabilities of Mg-rich iron oxide spinels from tuffite

    Directory of Open Access Journals (Sweden)

    W. N. Mussel

    1999-12-01

    Full Text Available Maghemite (γFe2O3 from tuffite is exceptionally rich in Mg, relatively to most of those reportedly found in other mafic lithosystems. To investigate in detail the compositional and structural variabilities of this natural magnetic iron oxide, sets of crystals were isolated from samples collected at different positions in a tuffite weathering mantle. These sets of crystal were individually powdered and studied by X-ray diffractometry, Mössbauer spectroscopy, magnetization measurements and chemical analysis. Lattice parameter of the cubic cell (a0 was found to vary from 0.834(1 to 0.8412(1 nm. Lower a0-values are characteristic of maghemite whereas higher ones are related to a magnetite precursor. FeO content ranges up to 17 mass % and spontaneous magnetization ranges from 8 to 32 J T-1 kg-1. Zero-field room temperature Mössbauer spectra are rather complex, indicating that the hyperfine field distributions due to Fe3+ and mixed valence Fe3+/2+ overlap. The structural variabilities of the (Mg, Ti-rich iron oxide spinels is essentially related to the range of chemical composition of its precursor (Mg, Ti-rich magnetite, and probably to the extent to which it has been oxidized during transformation in soil.

  8. The study of a Mg-rich epoxy primer for protection of AZ91D magnesium alloy

    International Nuclear Information System (INIS)

    Lu Xiangyu; Zuo Yu; Zhao Xuhui; Tang Yuming; Feng Xingguo

    2011-01-01

    Research highlights: → A Mg-rich epoxy primer was prepared by adding pure magnesium particles in epoxy coating. Cross scratch testing results showed that in 3% NaCl solution the Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. → The open circuit potential of AZ91D alloy in NaCl solution decreased after coated with Mg-rich coating, suggesting that cathodic protection effect of the Mg-rich coating on AZ91D alloy was present. → EIS studies showed that during the immersion tests of AZ91D alloy with Mg-rich coating the magnesium particles in coating dissolved with the charge-transfer resistance R ct at the magnesium particle/coating interface decreased and the double-layer capacitance Q dl increased. While the coating resistance remained stable for a long time and corrosion of the AZ91D alloy substrate was obviously delayed. - Abstract: A Mg-rich epoxy primer was prepared by adding pure magnesium particles to an epoxy coating. The coating properties were studied with electrochemical impedance spectroscopy (EIS), scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. The open circuit potential measurements showed cathodic protection effect of the Mg-rich primer on AZ91D alloy. Cross scratch testing showed that the Mg-rich primer provided better protection for the substrate than original epoxy coating. The precipitation of Mg(OH) 2 in the coating also provided some degree of barrier protection.

  9. The Pressure-Volume-Temperature Equation of State of Iron-Rich (Mg,Fe)O

    Science.gov (United States)

    Wicks, J. K.; Jackson, J. M.; Zhuravlev, K. K.; Prakapenka, V.

    2012-12-01

    Seismic observations near the base of the core-mantle boundary (CMB) have detected 5-20 km thick patches in which the seismic wave velocities are reduced by up to 30%. These ultra-low velocity zones (ULVZs) have been interpreted as aggregates of partially molten material (e.g. Williams and Garnero 1996, Hernlund and Jellinek, 2010) or as solid, iron-enriched residues (e.g. Knittle and Jeanloz, 1991; Mao et al., 2006; Wicks et al., 2010), typically based on proposed sources of velocity reduction. The stabilities of these structure types have been explored through dynamic models that have assembled a relationship between ULVZ stability and density (Hernlund and Tackley, 2007; Bower et al., 2010). Now, to constrain the chemistry of ULVZs, more information is needed on the relationship between density and sound velocity of candidate phases. Recently, we have shown that the characteristically low sound speeds of ULVZs can be produced by small amounts of iron-rich (Mg,Fe)O, which is likely to be found in iron-rich assemblages based on current partitioning studies (eg. Sakai et al., 2010; Tange et al., 2009). We determined the Debye velocity (VD) of (Mg.1657Fe.84)O using nuclear resonant inelastic x-ray scattering (NRIXS), and calculated the seismically relevant compressional (VP) and shear (VS) wave velocities up to 120 GPa using an equation of state of a similar composition (Wicks et al., 2010). These densities and sound velocities, in turn, are consistent with reasonable morphologies of modeled solid ULVZs (Bower et al., 2011). To increase the accuracy of density and sound velocity predictions, measurements must be made at elevated temperatures to correctly predict the properties of iron-rich (Mg,Fe)O at mantle conditions. In this study, we present the pressure-volume-temperature equation of state of (Mg.0657Fe.94)O measured up to pressures of 120 GPa and temperatures of 2000 K. Volume was measured with x-ray diffraction at beamline 13-ID-D of the Advanced Photon

  10. Growth and Yield Stimulation of Winter Oilseed Rape (Brasssica Napus L. by Mg-Titanit Fertiliser

    Directory of Open Access Journals (Sweden)

    Kováčik Peter

    2014-12-01

    Full Text Available The effort to achieve higher yields at the required qualitative level has led to the intensive studying the problems of the rational usage of the titanium containing fertilisers by the agricultural research in the course the previous thirty years. Therefore, the objective of the experiment was to evaluate the impact of two doses of Mg-Titanit (0.2 l/ha and 0.4 l/ha on the formation of the aboveground and underground phytomass, also on the total chlorophyll in leaves, on the titanium and nitrogen content in the seeds and straw, on the quantity and quality of winter rape yield. The doses were applied two or three times on the leaves of winter rape (BBCH 50-52, BBCH 59, BBCH 66-67. The experiment was realized on the Haplic Chernozem (48°42´ N, 17°70´ E - Western Slovakia during two farming years (2009/2010 and 2010/2011. The results showed that all three applications of Mg-Titanit in both doses stimulated the formation of aboveground and underground phytomass of winter rape. The highest growth of phytomass was detected after the second application. The application of Mg-Titanit in the growth phases BBCH 50-52 and BBCH 59 increased the contents of both chlorophylls (a and b, where the growth of chlorophyll b content was more considerable than the growth of chlorophyll a content. The third spraying by Mg-Titanit decreased the content of the total chlorophyll. The application of Mg-Titanit had the positive impact on the yield of seeds, straw and fat content in the winter oilseed rape seeds.

  11. Formation of Fe- and Mg-Rich Smectite under Hyperalkaline Conditions at Narra in Palawan, the Philippines

    OpenAIRE

    Shimbashi, Misato; Sato, Tsutomu; Yamakawa, Minoru; Fujii, Naoki; Otake, Tsubasa

    2018-01-01

    The formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions, as secondary minerals after the alkaline alteration of bentonite in repositories for radioactive waste, is of major concern. It is crucial for safety assessments to know whether smectite is formed as a secondary mineral after the alkaline alteration of bentonite. In the present paper, Fe- and Mg-rich smectite, which interacted with the hyperalkaline groundwater at Narra in Palawan, Philippines, was used. Mineralo...

  12. Evolution of Single Particle and Collective properties in the Neutron-Rich Mg Isotopes

    CERN Multimedia

    Reiter, P; Wiens, A; Fitting, J; Lauer, M; Van duppen, P L E; Finke, F

    2002-01-01

    We propose to study the single particle and collective properties of the neutron-rich Mg isotopes in transfer reactions and Coulomb excitation using REX-ISOLDE and MINIBALL. From the Coulomb excitation measurement precise and largely model independent B( E2 ; 0$^{+}_{g.s.}\\rightarrow$ 2$^{+}_{1}$ ) will be determined for the even-even isotopes. For the odd isotopes the distribution of the E2 strength over a few low-lying states will be measured. The sign of the M1/E2 mixing ratio, extracted from angular distributions, is characteristic of the sign of the deformation, as is the resulting level scheme. The neutron-pickup channel in the transfer reactions will allow for a determination of the single particle properties (spin, parity, spectroscopic factors) of these nuclei. This information will give new insights in changes of nuclear structure in the vicinity of the island of deformation around $^{32}$Mg. A total of 24 shifts of REX beam time is requested.

  13. Yield Evaluation of Nutrient-rich Potato Clones in High Hill of Nepal

    Directory of Open Access Journals (Sweden)

    Binod Prasad Luitel

    2017-05-01

    Full Text Available A study was conducted to evaluate the yield of nutrient-rich potato clones in high-hill districts: Dolakha and Jumla of Nepal during the years 2013 and 2014, respectively. Fourteen potato clones were tested as on-station and on-farm experiments at both districts, and those fourteen clones were compared to ‘Lady Rosita’ and ‘Jumli Local’ respectively as the check varieties in the first year experiment, 2013. Eight promising clones were selected from the first year experiment, and were evaluated and compared with same local varieties in the consecutive year, 2014. Two clones namely; CIP 395112.32 (19.3 tha-1 and CIP 393073.179 (17.8 tha-1 exhibited superior marketable tuber yield than that of ‘Lady Rosita’(14.2 tha-1 in Dolakha and five CIP clones namely; 395112.32 (25.5 tha-1, 393073.179 (22.5 tha-1, 394611.112 (20.9 tha-1, 390478.9 (19.9 tha-1 and 395017.229 (17.0 tha-1 showed higher marketable tuber yield than ‘Jumli Local’(14.5 tha-1. Based on two years’ phenotypic and tuber yield result, clones CIP 395112.32 and CIP 393073.179 are recommended to potato growers at high hills of Nepal for commercial cultivation.

  14. Predictive calculation of phase formation in Al-rich Al-Zn-Mg-Cu-Sc-Zr alloys using a thermodynamic Mg-alloy database

    International Nuclear Information System (INIS)

    Groebner, J.; Rokhlin, L.L.; Dobatkina, T.V.; Schmid-Fetzer, R.

    2007-01-01

    Three series of Al-rich alloys in the system Al-Zn-Mg-Cu-Sc-Zr and the subsystems Al-Zn-Mg-Cu-Sc and Al-Zn-Mg-Sc were studied by thermodynamic calculations. Phase formation was compared with experimental data obtained by DTA and microstructural analysis. Calculated phase diagrams, phase amount charts and enthalpy charts together with non-equilibrium calculations under Scheil conditions reveal significant details of the complex phase formation. This enables consistent and correct interpretation of thermal analysis data. Especially the interpretation of liquidus temperature and primary phase is prone to be wrong without using this tool of computational thermodynamics. All data are predictions from a thermodynamic database developed for Mg-alloys and not a specialized Al-alloy database. That provides support for a reasonable application of this database for advanced Mg-alloys beyond the conventional composition ranges

  15. Predictive calculation of phase formation in Al-rich Al-Zn-Mg-Cu-Sc-Zr alloys using a thermodynamic Mg-alloy database

    Energy Technology Data Exchange (ETDEWEB)

    Groebner, J. [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch Strasse 42, D-38678 Clausthal-Zellerfeld (Germany); Rokhlin, L.L. [Baikov Institute of Metallurgy and Materials Science, Leninsky prosp. 49, 119991 GSP-1, Moscow (Russian Federation); Dobatkina, T.V. [Baikov Institute of Metallurgy and Materials Science, Leninsky prosp. 49, 119991 GSP-1, Moscow (Russian Federation); Schmid-Fetzer, R. [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch Strasse 42, D-38678 Clausthal-Zellerfeld (Germany)]. E-mail: schmid-fetzer@tu-clausthal.de

    2007-05-16

    Three series of Al-rich alloys in the system Al-Zn-Mg-Cu-Sc-Zr and the subsystems Al-Zn-Mg-Cu-Sc and Al-Zn-Mg-Sc were studied by thermodynamic calculations. Phase formation was compared with experimental data obtained by DTA and microstructural analysis. Calculated phase diagrams, phase amount charts and enthalpy charts together with non-equilibrium calculations under Scheil conditions reveal significant details of the complex phase formation. This enables consistent and correct interpretation of thermal analysis data. Especially the interpretation of liquidus temperature and primary phase is prone to be wrong without using this tool of computational thermodynamics. All data are predictions from a thermodynamic database developed for Mg-alloys and not a specialized Al-alloy database. That provides support for a reasonable application of this database for advanced Mg-alloys beyond the conventional composition ranges.

  16. Solution of the spatial neutral model yields new bounds on the Amazonian species richness

    Science.gov (United States)

    Shem-Tov, Yahav; Danino, Matan; Shnerb, Nadav M.

    2017-02-01

    Neutral models, in which individual agents with equal fitness undergo a birth-death-mutation process, are very popular in population genetics and community ecology. Usually these models are applied to populations and communities with spatial structure, but the analytic results presented so far are limited to well-mixed or mainland-island scenarios. Here we combine analytic results and numerics to obtain an approximate solution for the species abundance distribution and the species richness for the neutral model on continuous landscape. We show how the regional diversity increases when the recruitment length decreases and the spatial segregation of species grows. Our results are supported by extensive numerical simulations and allow one to probe the numerically inaccessible regime of large-scale systems with extremely small mutation/speciation rates. Model predictions are compared with the findings of recent large-scale surveys of tropical trees across the Amazon basin, yielding new bounds for the species richness (between 13100 and 15000) and the number of singleton species (between 455 and 690).

  17. Abnormal devitrification behavior and mechanical response of cold-rolled Mg-rich Mg-Cu-Gd metallic glasses

    International Nuclear Information System (INIS)

    Lee, J.I.; Kim, J.W.; Oh, H.S.; Park, J.S.; Park, E.S.

    2016-01-01

    Abnormal devitrification behavior and mechanical response of Mg 75 Cu 15 Gd 10 (relatively strong glass former with higher structural stability) and Mg 85 Cu 5 Gd 10 (relatively fragile glass former with lower structural stability) metallic glasses, fabricated by repeated forced cold rolling, have been investigated. When metallic glasses were cold-rolled up to a thickness reduction ratio of ∼33%, the heat of relaxation (ΔH relax. ) below T g of the cold-rolled specimens was reduced, which indicates the formation of local structural ordering via cold rolling due to stress-induced relaxation. The local structural ordering results in abnormal devitrification behavior, such as higher resistance of glass-to-supercooled liquid transition and delayed growth, in the following heat treatment due to increased nuclei density and pinning site. In particular, the fragility index, m, could assist in understanding structural stability and local structural variation by mechanical processing as well as compositional tuning. Indeed, we examine the shear avalanche size to rationalize the variation of the deformation unit size depending on the structural instability before and after cold rolling. The deformation mode in Mg 85 Cu 5 Gd 10 metallic glass might change from self-organized critical state to chaotic state by cold rolling, which results in unique hardening behavior under the condition for coexisting well distributed local structural ordering and numerous thinner shear deformed areas. These results would give us a guideline for atomic scale structural manipulation of metallic glasses, and help develop novel metallic glass matrix composites with optimal properties through effective mechanical processing as well as heat treatment.

  18. Very low sound velocities in iron-rich (Mg,Fe)O: Implications for the core-mantle boundary region

    International Nuclear Information System (INIS)

    Wicks, J.K.; Jackson, J.M.; Sturhahn, W.

    2010-01-01

    The sound velocities of (Mg .16 Fe .84 )O have been measured to 121 GPa at ambient temperature using nuclear resonant inelastic x-ray scattering. The effect of electronic environment of the iron sites on the sound velocities were tracked in situ using synchrotron Moessbauer spectroscopy. We found the sound velocities of (Mg .16 Fe .84 )O to be much lower than those in other presumed mantle phases at similar conditions, most notably at very high pressures. Conservative estimates of the effect of temperature and dilution on aggregate sound velocities show that only a small amount of iron-rich (Mg,Fe)O can greatly reduce the average sound velocity of an assemblage. We propose that iron-rich (Mg,Fe)O be a source of ultra-low velocity zones. Other properties of this phase, such as enhanced density and dynamic stability, strongly support the presence of iron-rich (Mg,Fe)O in localized patches above the core-mantle boundary.

  19. Mg doping of GaN grown by plasma-assisted molecular beam epitaxy under nitrogen-rich conditions

    International Nuclear Information System (INIS)

    Zhang Meng; Bhattacharya, Pallab; Guo Wei; Banerjee, Animesh

    2010-01-01

    Acceptor doping of GaN with Mg during plasma-assisted molecular beam epitaxy, under N-rich conditions and a relatively high growth temperature of 740 deg. C, was investigated. The p-doping level steadily increases with increasing Mg flux. The highest doping level achieved, determined from Hall measurements, is 2.1x10 18 cm -3 . The corresponding doping efficiency and hole mobility are ∼4.9% and 3.7 cm 2 /V s at room temperature. Cross-sectional transmission electron microscopy and photoluminescence measurements confirm good crystalline and optical quality of the Mg-doped layers. An InGaN/GaN quantum dot light emitting diode (λ peak =529 nm) with p-GaN contact layers grown under N-rich condition exhibits a low series resistance of 9.8 Ω.

  20. Phase-field simulations of dendrite morphologies and selected evolution of primary {alpha}-Mg phases during the solidification of Mg-rich Mg-Al-based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Mingyue [Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Jing, Tao; Liu, Baicheng [Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

    2009-10-15

    A formulation of solid-liquid interfacial thermodynamic and kinetic anisotropic characteristics for hexagonal close-packed metals is proposed. The two- and three-dimensional dendritic growth of primary Mg in undercooled Mg-Al alloy melts is modeled using the phase-field method, based on a combination of crystallographic lattice symmetry and experimental observations. The morphologies of three-dimensional dendrites are obtained and the calculated results show intricately hierarchical branched structures. The excess free energy of the solution system is based on the Redlich-Kister model.

  1. Phase-field simulations of dendrite morphologies and selected evolution of primary α-Mg phases during the solidification of Mg-rich Mg-Al-based alloys

    International Nuclear Information System (INIS)

    Wang, Mingyue; Jing, Tao; Liu, Baicheng

    2009-01-01

    A formulation of solid-liquid interfacial thermodynamic and kinetic anisotropic characteristics for hexagonal close-packed metals is proposed. The two- and three-dimensional dendritic growth of primary Mg in undercooled Mg-Al alloy melts is modeled using the phase-field method, based on a combination of crystallographic lattice symmetry and experimental observations. The morphologies of three-dimensional dendrites are obtained and the calculated results show intricately hierarchical branched structures. The excess free energy of the solution system is based on the Redlich-Kister model.

  2. Influence of spray forming process parameters on the microstructure and porosity of Mg{sub 2}Si rich aluminum alloys

    Energy Technology Data Exchange (ETDEWEB)

    Stelling, O.; Hehl, A. von [Foundation Institute for Material Science, Bremen (Germany); Uhlenwinkel, V. [University of Bremen, FB4 FG01 Department Process and Chemcial Engineering, Bremen (Germany); Krug, P. [PEAK Werkstoff GmbH, Velbert (Germany); Ellendt, N.

    2010-07-15

    Due to high cooling rates spray forming is an appropriate process to produce aluminum alloys with a high content of Mg{sub 2}Si. Compared to common casting processes, a fine microstructure can be achieved yielding in improved mechanical properties. In this work, billets were spray formed from the two alloys AlMg15Si8Cu2 (22 mass-% Mg{sub 2}Si) and AlMg20.5Si11Cu2 (30 mass-% Mg{sub 2}Si) under different spraying conditions. The analysis of the microstructure showed that the size of Mg{sub 2}Si dispersoids is very sensitive to process parameters. Besides the well known thermal effects of melt superheat (carried out from -40 K to +170 K) and GMR (varied from 2.0 to 6.3) a strong influence of the scanning frequency of the atomizer nozzle (7 Hz and 15 Hz) could be observed. Similar effects could be found for the occurrence of porosity. A new parameter, the enthalpy flow to gas flow ratio (EGR), was defined from these two parameters of which correlations of Mg{sub 2}Si dispersoid size and amount of porosity were found. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  3. First principle investigations of the physical properties of hydrogen-rich MgH2

    KAUST Repository

    Zarshenas, Mohammed

    2013-11-28

    Hydrogen being a cleaner energy carrier has increased the importance of hydrogen-containing light metal hydrides, in particular those with large gravimetric hydrogen density like magnesium hydride (MgH2). In this study, density functional and density functional perturbation theories are combined to investigate the structural, elastic, thermodynamic, electronic and optical properties of MgH2. Our structural parameters calculated with those proposed by Perdew, Burke and Ernzerof generalized gradient approximation (PBE-GGA) and Wu-Cohen GGA (WC-GGA) are in agreement with experimental measurements, however the underestimated band gap values calculated using PBE-GGA and WC-GGA were greatly improved with the GGA suggested by Engle and Vosko and the modified Becke-Johnson exchange correlation potential by Trans and Blaha. As for the thermodynamic properties the specific heat values at low temperatures were found to obey the T3 rule and at higher temperatures Dulong and Petit\\'s law. Our analysis of the optical properties of MgH2 also points to its potential application in optoelectronics. © 2013 The Royal Swedish Academy of Sciences.

  4. First principle investigations of the physical properties of hydrogen-rich MgH2

    KAUST Repository

    Zarshenas, Mohammed; Ahmed, Rashid; Kanoun, Mohammed; Ul Haq, Bakhtiar; Isa, Ahmad Radzi Mat; Goumri-Said, Souraya

    2013-01-01

    Hydrogen being a cleaner energy carrier has increased the importance of hydrogen-containing light metal hydrides, in particular those with large gravimetric hydrogen density like magnesium hydride (MgH2). In this study, density functional and density functional perturbation theories are combined to investigate the structural, elastic, thermodynamic, electronic and optical properties of MgH2. Our structural parameters calculated with those proposed by Perdew, Burke and Ernzerof generalized gradient approximation (PBE-GGA) and Wu-Cohen GGA (WC-GGA) are in agreement with experimental measurements, however the underestimated band gap values calculated using PBE-GGA and WC-GGA were greatly improved with the GGA suggested by Engle and Vosko and the modified Becke-Johnson exchange correlation potential by Trans and Blaha. As for the thermodynamic properties the specific heat values at low temperatures were found to obey the T3 rule and at higher temperatures Dulong and Petit's law. Our analysis of the optical properties of MgH2 also points to its potential application in optoelectronics. © 2013 The Royal Swedish Academy of Sciences.

  5. Origin of the reversed yield asymmetry in Mg-rare earth alloys at high temperature

    International Nuclear Information System (INIS)

    Hidalgo-Manrique, P.; Herrera-Solaz, V.; Segurado, J.; Llorca, J.; Gálvez, F.; Ruano, O.A.; Yi, S.B.; Pérez-Prado, M.T.

    2015-01-01

    The mechanical behaviour in tension and compression of an extruded Mg–1 wt.% Mn–1 wt.% Nd (MN11) alloy was studied along the extrusion direction in the temperature range −175 °C to 300 °C at both quasi-static and dynamic strain rates. Microstructural analysis revealed that the as-extruded bar presents a recrystallized microstructure and a weak texture that remain stable in the whole temperature range. A remarkable reversed yield stress asymmetry was observed above 150 °C, with the compressive yield stress being significantly higher than the tensile yield stress. The origin of this anomalous reversed yield stress asymmetry, which to date remains unknown, was investigated through the analysis of the macro and microtexture development during deformation, as well as by means of crystal plasticity finite element simulations of a representative volume element of the polycrystal. The critical resolved shear stresses of slip and twining for simulated single crystals were obtained as a function of the temperature by means of an inverse optimisation strategy. Experimental and simulation results suggest that the reversed yield asymmetry may be primarily attributed to the non-Schmid behaviour of pyramidal 〈c + a〉 slip, which is the dominant deformation mechanism at high temperatures. It is proposed, furthermore, that the asymmetry is enhanced at quasi-static strain rates by the stronger interaction of 〈c + a〉 dislocations with the diffusing solute atoms and particles in compression than in tension

  6. Theoretical evidence for unexpected O-rich phases at corners of MgO surfaces

    Science.gov (United States)

    Bhattacharya, Saswata; Berger, Daniel; Reuter, Karsten; Ghiringhelli, Luca M.; Levchenko, Sergey V.

    2017-12-01

    Realistic oxide materials are often semiconductors, in particular at elevated temperatures, and their surfaces contain undercoordinated atoms at structural defects such as steps and corners. Using hybrid density-functional theory and ab initio atomistic thermodynamics, we investigate the interplay of bond-making, bond-breaking, and charge-carrier trapping at the corner defects at the (100) surface of a p -doped MgO in thermodynamic equilibrium with an O2 atmosphere. We show that by manipulating the coordination of surface atoms, one can drastically change and even reverse the order of stability of reduced versus oxidized surface sites.

  7. Forecasting the Yield Curve in a Data-Rich Environment Using the Factor-Augmented Nelson-Siegel Model

    DEFF Research Database (Denmark)

    Exterkate, Peter; Dijk, Dick van; Heij, Christiaan

    2013-01-01

    This paper compares various ways of extracting macroeconomic information from a data-rich environment for forecasting the yield curve using the Nelson–Siegel model. Five issues in extracting factors from a large panel of macro variables are addressed; namely, selection of a subset of the available......, with principal component methods ranking second best. Reductions of mean squared prediction errors of 20–30% are attained, compared to the Nelson–Siegel model without macro factors....

  8. Adsorption of nucleotides onto Fe-Mg-Al rich swelling clays

    Science.gov (United States)

    Feuillie, Cécile; Daniel, Isabelle; Michot, Laurent J.; Pedreira-Segade, Ulysse

    2013-11-01

    Mineral surfaces may have played a role in the origin of the first biopolymers, by concentrating organic monomers from a dilute ocean. Swelling clays provide a high surface area for the concentration of prebiotic monomers, and have therefore been the subject of numerous investigations. In that context, montmorillonite, the most abundant swelling clay in modern environments, has been extensively studied with regard to adsorption and polymerization of nucleic acids. However, montmorillonite was probably rather marginal on the primitive ocean floor compared to iron-magnesium rich phyllosilicates such as nontronite that results from the hydrothermal alteration of a mafic or ultramafic oceanic crust. In the present paper, we study the adsorption of nucleotides on montmorillonite and nontronite, at various pH and ionic strength conditions plausible for Archean sea-water. A thorough characterization of the mineral surfaces shows that nucleotide adsorb mainly on the edge faces of the smectites by ligand exchange between the phosphate groups of the nucleotides and the -OH groups from the edge sites over a wide pH range (4-10). Nontronite is more reactive than montmorillonite. At low pH, additional ion exchange may play a role as the nucleotides become positively charged.

  9. Ultraviolet electroluminescence from Au/MgO/MgxZn1−xO heterojunction diodes and the observation of Zn-rich cluster emission

    International Nuclear Information System (INIS)

    Liu, C.Y.; Xu, H.Y.; Sun, Y.; Zhang, C.; Ma, J.G.; Liu, Y.C.

    2014-01-01

    In this work, ultraviolet (UV) electroluminescence (EL) is achieved from Au/MgO/Mg x Zn 1−x O heterojunction diodes. The EL mechanism and laser forming process are discussed based on the energy band diagram, impact-ionization process and disordered optical structure. For ZnO and low Mg-content MgZnO devices, their EL spectra show single near-band-edge (NBE) emission. While in high Mg-content MgZnO devices, the emission from self-formed Zn-rich MgZnO clusters is observed and also contribute to the UV EL band. These Zn-rich clusters can act as thermally-stable luminescence centers, suggesting a promising route for developing MgZnO-based UV light-emitting devices. -- Highlights: • A series of Au/MgO/Mg x Zn 1−x O heterojunction diodes with multiple Mg compositions are fabricated and ultraviolet electroluminescence is achieved. • EL mechanism and laser forming process are discussed based on energy band diagram, impact-ionization process and disordered optical structure. • The transition from spontaneous to stimulated emission is observed in these heterojunctions, and the lasing mode is random laser. • In high Mg-content MgZnO devices, the emission from self-formed Zn-rich clusters is observed, which are thermally stable luminescence centers

  10. Environmental Change: Precipitation and N, P, K, mg Fertilization Influences on Crop Yield Under Temperate Climate Conditions

    Science.gov (United States)

    László Phd, Dd. M.

    2009-04-01

    Summary: Agroecological quality has a well estabished dependence on climate-rainfall changes because the water problems are pressing. Therefore, there is, growing concern about the potentially wide ranging risks that climate change would have on these key industries as the nature and extent of anticipated changes have become more evident. It also includes changes in land use and in plant production and their management. These changes are unprecedented in terms of both their rate and their spatial extent. Changes in land use (agrotechnics, soil, cultivation, fertility, quality, protection etc.) and in plant production (plant, nutrition, rotation, protection etc.) are currently the main manifestations. As an interdisciplinary problem it is necessary to study such a complex matter in terms of agricultural production. Generally, among natural catastrophes, droughts and floods cause the greatest problems in field crop production. The droughts and the floods that were experienced in Hungary in the early 1980s have drawn renewed attention to the analyses of these problems. New research on climate change-soil-plant systems are focused on yield and yield quality. This paper reports of the climate changes (rainfall); soil (acidic sandy brown forest) properties, mineral N, P, K, Mg fertilisation level and plant interactions on rye (Secale cereale L.), on potato (Solanum tuberosum L.) and on winter wheat (Triticum aestivum L.) yields in a long term field experiment set up at Nyírlugos in north-eastern Hungary under temperate climate conditions in 1962. Results are summarised from 1962 to 1990. Main conclusions were as follows: 1. Rye: a, Experimental years were characterised by frequent extremes of precipitation variabilities and changes. b, By an average year, at a satisfactory fertilisation level (N: 90 kg ha-1 and NP, NK, NPK, NPKMg combinations) the maximum yield reached 3.8 t ha-1. But yield was decreased by 17% and by 52% due to drought and excess rainfall, respectively

  11. Microstructural evolution of Fe-rich particles in an Al-Zn-Mg-Cu alloy during equal-channel angular pressing

    International Nuclear Information System (INIS)

    Sha, G.; Wang, Y.B.; Liao, X.Z.; Duan, Z.C.; Ringer, S.P.; Langdon, T.G.

    2010-01-01

    The microstructures of a severely deformed Al-Zn-Mg-Cu (AA7136) alloy have been characterized carefully using transmission electron microscopy and three-dimensional atom probe analysis. The Fe-rich intermetallic particles are predominantly Al 13 Fe 4 type in the as-extruded alloy. Significantly, equal-channel angular pressing (ECAP) at 200 deg. C refines Fe-rich particles from ∼1 to 2 μm to as small as ∼50 nm after 4 passes processing, and effectively narrow down their size distribution with the increase of number of ECAP passes. In addition, small Fe-rich particles evolve into spherical morphology and are in a more uniform distribution. The formations of Fe-rich phases in AA7136, the kinetic and thermodynamic effects in relation to the refinement of Fe-rich particles and their morphology evolution during ECAP processing are discussed.

  12. Ab-initio study of the interfacial properties in ultrathin MgO films on O-rich FeO/Fe(001) surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Junjin; Yu, Byungdeok [University of Seoul, Seoul (Korea, Republic of)

    2014-09-15

    Using ab-initio simulations based on density functional theory, we systematically studied the interfacial properties of MgO films on O-rich FeO/Fe(001) surfaces with increasing number of MgO layers from one to three monolayers (MLs). The structural and the adhesion properties of the MgO/FeO/Fe(001) system were assessed and compared with those of simple MgO/Fe(001) interfaces. Our calculated results showed that the adhesion energy for MgO/FeO/Fe(001) was smaller than that for simple MgO/Fe(001). An analysis of the electronic structures and the charge rearrangements of the MgO/FeO/Fe(001) interfaces was also performed. The work functions of the MgO/FeO/Fe(001) systems upon the deposition of MgO films exhibited smaller decreases (0.45 - 0.67 eV) than those (1.43 - 1.74 eV) of the MgO/Fe(001) systems. In addition, the obtained work functions (3.77 - 3.99 eV) for MgO/FeO/Fe(001) were much larger than those (2.12 - 2.43 eV) for MgO/Fe(001).

  13. Methane-yielding microbial communities processing lactate-rich substrates: a piece of the anaerobic digestion puzzle.

    Science.gov (United States)

    Detman, Anna; Mielecki, Damian; Pleśniak, Łukasz; Bucha, Michał; Janiga, Marek; Matyasik, Irena; Chojnacka, Aleksandra; Jędrysek, Mariusz-Orion; Błaszczyk, Mieczysław K; Sikora, Anna

    2018-01-01

    Anaerobic digestion, whose final products are methane and carbon dioxide, ensures energy flow and circulation of matter in ecosystems. This naturally occurring process is used for the production of renewable energy from biomass. Lactate, a common product of acidic fermentation, is a key intermediate in anaerobic digestion of biomass in the environment and biogas plants. Effective utilization of lactate has been observed in many experimental approaches used to study anaerobic digestion. Interestingly, anaerobic lactate oxidation and lactate oxidizers as a physiological group in methane-yielding microbial communities have not received enough attention in the context of the acetogenic step of anaerobic digestion. This study focuses on metabolic transformation of lactate during the acetogenic and methanogenic steps of anaerobic digestion in methane-yielding bioreactors. Methane-yielding microbial communities instead of pure cultures of acetate producers were used to process artificial lactate-rich media to methane and carbon dioxide in up-flow anaerobic sludge blanket reactors. The media imitated the mixture of acidic products found in anaerobic environments/digesters where lactate fermentation dominates in acidogenesis. Effective utilization of lactate and biogas production was observed. 16S rRNA profiling was used to examine the selected methane-yielding communities. Among Archaea present in the bioreactors, the order Methanosarcinales predominated. The acetoclastic pathway of methane formation was further confirmed by analysis of the stable carbon isotope composition of methane and carbon dioxide. The domain Bacteria was represented by Bacteroidetes , Firmicutes , Proteobacteria , Synergistetes , Actinobacteria , Spirochaetes , Tenericutes , Caldithrix , Verrucomicrobia , Thermotogae , Chloroflexi , Nitrospirae, and Cyanobacteria. Available genome sequences of species and/or genera identified in the microbial communities were searched for genes encoding the lactate

  14. Effect of Ce-rich rare earth on microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy

    Directory of Open Access Journals (Sweden)

    You Zhiyong

    2012-05-01

    Full Text Available To improve the comprehensive mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy, different amount of Ce-rich rare earth (RE was added to the alloy, and the effect of RE addition on the microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb alloy was investigated by means of Brinell hardness measurement, scanning electron microscopy (SEM, energy dispersive spectroscope (EDS and X-ray diffraction (XRD. The results show that an appropriate amount of Ce-rich rare earth addition can make the Al4Ce phase particles and CeSb phase disperse more evenly in the alloy. These phases refine the alloy抯 matrix and make the secondary phases [t-Mg32(Al,Zn49 phase and f-Al2Mg5Zn2 phase] finer and more dispersive, therefore significantly improve the mechanical properties of the Mg-10Zn-5Al-0.1Sb alloy. When the RE addition is 1.0 wt.%, the tensile strengths of the alloy both at room temperature and 150 篊 reach the maximum values while the impact toughness is slightly lower than that of the matrix alloy. The hardness increases with the increase of RE addition.

  15. Formation of Si-Al-Mg-Ca-rich zoned magnetite in an end-Permian phreatomagmatic pipe in the Tunguska Basin, East Siberia

    Science.gov (United States)

    Neumann, Else-Ragnhild; Svensen, Henrik H.; Polozov, Alexander G.; Hammer, Øyvind

    2017-12-01

    Magma-sediment interactions in the evaporite-rich Tunguska Basin resulted in the formation of numerous phreatomagmatic pipes during emplacement of the Siberian Traps. The pipes contain magnetite-apatite deposits with copper and celestine mineralization. We have performed a detailed petrographic and geochemical study of magnetite from long cores drilled through three pipe breccia structures near Bratsk, East Siberia. The magnetite samples are zoned and rich in Si (≤5.3 wt% SiO2), Ca, Al, and Mg. They exhibit four textural types: (1) massive ore in veins, (2) coating on breccia clasts, (3) replacement ore, and (4) reworked ore at the crater base. The textural types have different chemical characteristics. "Breccia coating" magnetite has relatively low Mg content relative to Si, as compared to the other groups, and appears to have formed at lower oxygen fugacity. Time series analyses of MgO variations in microprobe transects across Si-bearing magnetite in massive ore indicate that oscillatory zoning in the massive ore was controlled by an internal self-organized process. We suggest that hydrothermal Fe-rich brines were supplied from basalt-sediment interaction zones in the evaporite-rich sedimentary basin, leading to magnetite ore deposition in the pipes. Hydrothermal fluid composition appears to be controlled by proximity to dolerite fragments, temperature, and oxygen fugacity. Magnetite from the pipes has attributes of iron oxide-apatite deposits (e.g., textures, oscillatory zoning, association with apatite, and high Si content) but has higher Mg and Ca content and different mineral assemblages. These features are similar to magnetite found in skarn deposits. We conclude that the Siberian Traps-related pipe magnetite deposit gives insight into the metamorphic and hydrothermal effects following magma emplacement in a sedimentary basin.

  16. Shape coexistence in the N=19 neutron-rich nucleus 31Mg explored by β–γ spectroscopy of spin-polarized 31Na

    Directory of Open Access Journals (Sweden)

    H. Nishibata

    2017-04-01

    Full Text Available The structure of excited states in the neutron-rich nucleus 31Mg, which is in the region of the “island of inversion” associated with the neutron magic number N=20, is studied by β–γ spectroscopy of spin-polarized 31Na. Among the 31Mg levels below the one neutron separation energy of 2.3 MeV, the spin values of all five positive-parity levels are unambiguously determined by observing the anisotropic β decay. Two rotational bands with Kπ=1/2+ and 1/2− are proposed based on the spins and energies of the levels. Comparison on a level-by-level basis is performed between the experimental results and theoretical calculations by the antisymmetrized molecular dynamics (AMD plus generator coordinate method (GCM. It is found that various nuclear structures coexist in the low excitation energy region in 31Mg.

  17. Low yield syntheses of [18F]FDG at CDTN/CNEN-MG: problem diagnosis and corrective actions

    International Nuclear Information System (INIS)

    Dalle, Hugo M.; Silva, Juliana B.; Valente, Eduardo S.; Malamut, Carlos; Nascimento, Leonardo T.C.; Silveira, Marina B.; Ferreira, Soraya M.Z.M.D.; Borges, Leonardo T.; Truong, Phong; Olsson, Ake

    2017-01-01

    The Nuclear Technology Development Center manages, since 2007, a Radiopharmaceuticals Research and Production Unit. In the first months of 2014, the radiopharmaceuticals syntheses yields started to fall well under the nominal values. This paper presents a summary of the tests performed to identify the causes of the low yield syntheses and the actions taken to resolve. By sharing our experience, we aim to help other radiopharmaceuticals producers facing similar situation, as solution may not be trivial, neither fast nor cheap. (author)

  18. Low yield syntheses of [{sup 18}F]FDG at CDTN/CNEN-MG: problem diagnosis and corrective actions

    Energy Technology Data Exchange (ETDEWEB)

    Dalle, Hugo M.; Silva, Juliana B.; Valente, Eduardo S.; Malamut, Carlos; Nascimento, Leonardo T.C.; Silveira, Marina B.; Ferreira, Soraya M.Z.M.D.; Borges, Leonardo T. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Truong, Phong [GE Healthcare do Brasil, São Paulo, SP (Brazil); Olsson, Ake, E-mail: dallehm@cdtn.br, E-mail: leonardo.borges@ge.com, E-mail: phong.truong@ge.com [GE Healthcare, Uppsala (Sweden)

    2017-07-01

    The Nuclear Technology Development Center manages, since 2007, a Radiopharmaceuticals Research and Production Unit. In the first months of 2014, the radiopharmaceuticals syntheses yields started to fall well under the nominal values. This paper presents a summary of the tests performed to identify the causes of the low yield syntheses and the actions taken to resolve. By sharing our experience, we aim to help other radiopharmaceuticals producers facing similar situation, as solution may not be trivial, neither fast nor cheap. (author)

  19. Calculation of the total electron excitation cross section in the Born approximation using Slater wave functions for the Li (2s yields 2p), Li (2s yields 3p), Na (3s yields 4p), Mg (3p yields 4s), Ca (4s yields 4p) and K (4s yields 4p) excitations. M.S. Thesis

    Science.gov (United States)

    Simsic, P. L.

    1974-01-01

    Excitation of neutral atoms by inelastic scattering of incident electrons in gaseous nebulae were investigated using Slater Wave functions to describe the initial and final states of the atom. Total cross sections using the Born Approximation are calculated for: Li(2s yields 2p), Na(3s yields 4p), k(4s yields 4p). The intensity of emitted radiation from gaseous nebulae is also calculated, and Maxwell distribution is employed to average the kinetic energy of electrons.

  20. Synthesis and crystal structure of Mg2B24C, a new boron-rich boride related to 'tetragonal boron I'

    International Nuclear Information System (INIS)

    Adasch, Volker; Hess, Kai-Uwe; Ludwig, Thilo; Vojteer, Natascha; Hillebrecht, Harald

    2006-01-01

    Single crystals of Mg 2 B 24 C, a new boron-rich boridecarbide of magnesium, were synthesized as black needles and columns by reaction of the elements in Ta ampoules and BN crucibles at 1300 deg. C. The crystal structure was determined by X-ray diffraction (P-4n2, a=8.9391(13)A, c=5.0745(10)A, Z=2, 713 reflections, 64 variables, R 1 (F)=0.0235, wR 2 (I)=0.0591). It is closely related to 'tetragonal boron I' and can be described as a tetragonal rod packing of corner-linked B 12 icosahedra with C and Mg atoms in the voids. Each B 12 icosahedron has 2 B-C bonds and 10 exohedral bonds to other icosahedra, 2 within the rod and 4x2 to neighbouring rods. The isolated C atoms are 4-fold coordinated forming distorted tetrahedra. Mg is placed on two crystallographically independent positions within the three-dimensional B 12 C network. Mg 2 B 24 C is the first example for a compound related to 'tetragonal boron I' with a stoichiometric composition

  1. The effect of Fe-rich intermetallics on the microstructure, hardness and tensile properties of Al–Mg2Si die-cast composite

    International Nuclear Information System (INIS)

    Emamy, M.; Emami, A.R.; Khorshidi, R.; Ghorbani, M.R.

    2013-01-01

    Highlights: ► Effect of Fe on the microstructure and mechanical properties of Al–Mg 2 Si composite. ► Fe changed the size of primary Mg 2 Si from 33 μm to 15 μm. ► Higher hardness, YS, UTS and Quality Index values obtained from Fe addition. ► Different morphologies of Fe-intermetallics were found with higher Fe contents. - Abstract: In present paper, an attempt was made to examine the effect of different concentrations of Fe (0.5, 1, 1.5, 2 and 3 wt.%) on the microstructure and tensile properties of an in situ Al–15wt.%Mg 2 Si metal matrix composite (MMC). The composite was made by casting process and characterized by optical microscope, scanning electron microscope (SEM) equipped with energy dispersive X-ray spectroscopy. The results depicted that the addition of 2 wt.% Fe to the MMC changes the morphology of primary Mg 2 Si from irregular to polyhedral shape and reduces its average particle size from 33 μm to 15 μm. The microstructural studies also showed that the addition of Fe leads to the formation of Fe-rich intermetallics with polyhedral, plate-like and star-like morphology. Hardness results demonstrated that Fe addition to Al–15%Mg 2 Si composite has a positive effect on the hardness improvement. Further investigations on tensile tests revealed optimum Fe (1 wt.%) level for improving tensile properties. In the point of fracture behavior of the composite, Fe-containing specimens showed a brittle mode of failure

  2. Carcass and cut yields of broiler chickens fed diet containing purslane meal rich in omega-3 fats

    Science.gov (United States)

    Kartikasari, LR; Hertanto, B. S.; Nuhriawangsa, A. MP

    2018-01-01

    The aim of the research was to investigate the effect of diets containing Portulaca oleraceae (purslane) as a source of omega-3 fats on carcass and cut yields of broiler chickens. One-day old unsexed Lohmann broiler chickens (n = 180) were used and randomly allocated into 30 pens (each pen contained 6 birds). The pens were randomly assigned to five experimental diets with 6 replicates (36 birds per treatment). The diets were formulated by supplementing a basal diet with purslane meal at a level of 0, 1.5, 3.0, 4.5 and 6.0%. For a period of 42 days, water and diets were provided ad libitum. Feed intake and body weight gain were collected weekly to determine feed conversion ratio. The collected data were analysed using analysis of variance. If there were significant differences between treatment means, the analysis was continued by Duncan’s New Multiple Range Test. Findings showed that diets enriched with omega-3 fats, alpha-linolenic acid did not change body weight and carcass percentage of broilers. In terms of cuts yield, there was no significant different on the percentage of breast, back and wings by feeding diets supplemented with purslane meal. However, the inclusion levels of dietary purslane meal significantly affected the percentage of thighs (P<0.05) with the highest weight achieved for diets supplemented with 3% purslane meal. Drumsticks tended to increase (P = 0.056) by feeding the experimental diets. It was concluded that the inclusion level of 6% purslane meal didn’t have negative effect on carcass and cut yields of broiler chickens.

  3. Low-temperature MIR to submillimeter mass absorption coefficient of interstellar dust analogues. II. Mg and Fe-rich amorphous silicates

    Science.gov (United States)

    Demyk, K.; Meny, C.; Leroux, H.; Depecker, C.; Brubach, J.-B.; Roy, P.; Nayral, C.; Ojo, W.-S.; Delpech, F.

    2017-10-01

    Context. To model the cold dust emission observed in the diffuse interstellar medium, in dense molecular clouds or in cold clumps that could eventually form new stars, it is mandatory to know the physical and spectroscopic properties of this dust and to understand its emission. Aims: This work is a continuation of previous studies aiming at providing astronomers with spectroscopic data of realistic cosmic dust analogues for the interpretation of observations. The aim of the present work is to extend the range of studied analogues to iron-rich silicate dust analogues. Methods: Ferromagnesium amorphous silicate dust analogues were produced by a sol-gel method with a mean composition close to Mg1-xFexSiO3 with x = 0.1, 0.2, 0.3, 0.4. Part of each sample was annealed at 500 °C for two hours in a reducing atmosphere to modify the oxidation state of iron. We have measured the mass absorption coefficient (MAC) of these eight ferromagnesium amorphous silicate dust analogues in the spectral domain 30-1000 μm for grain temperature in the range 10-300 K and at room temperature in the 5-40 μm range. Results: The MAC of ferromagnesium samples behaves in the same way as the MAC of pure Mg-rich amorphous silicate samples. In the 30-300 K range, the MAC increases with increasing grain temperature whereas in the range 10-30 K, we do not see any change of the MAC. The MAC cannot be described by a single power law in λ- β. The MAC of the samples does not show any clear trend with the iron content. However the annealing process has, on average, an effect on the MAC that we explain by the evolution of the structure of the samples induced by the processing. The MAC of all the samples is much higher than the MAC calculated by dust models. Conclusions: The complex behavior of the MAC of amorphous silicates with wavelength and temperature is observed whatever the exact silicate composition (Mg vs. Fe amount). It is a universal characteristic of amorphous materials, and therefore of

  4. A Combined Precipitation, Yield Stress, and Work Hardening Model for Al-Mg-Si Alloys Incorporating the Effects of Strain Rate and Temperature

    Science.gov (United States)

    Myhr, Ole Runar; Hopperstad, Odd Sture; Børvik, Tore

    2018-05-01

    In this study, a combined precipitation, yield strength, and work hardening model for Al-Mg-Si alloys known as NaMo has been further developed to include the effects of strain rate and temperature on the resulting stress-strain behavior. The extension of the model is based on a comprehensive experimental database, where thermomechanical data for three different Al-Mg-Si alloys are available. In the tests, the temperature was varied between 20 °C and 350 °C with strain rates ranging from 10-6 to 750 s-1 using ordinary tension tests for low strain rates and a split-Hopkinson tension bar system for high strain rates, respectively. This large span in temperatures and strain rates covers a broad range of industrial relevant problems from creep to impact loading. Based on the experimental data, a procedure for calibrating the different physical parameters of the model has been developed, starting with the simplest case of a stable precipitate structure and small plastic strains, from which basic kinetic data for obstacle limited dislocation glide were extracted. For larger strains, when work hardening becomes significant, the dynamic recovery was linked to the Zener-Hollomon parameter, again using a stable precipitate structure as a basis for calibration. Finally, the complex situation of concurrent work hardening and dynamic evolution of the precipitate structure was analyzed using a stepwise numerical solution algorithm where parameters representing the instantaneous state of the structure were used to calculate the corresponding instantaneous yield strength and work hardening rate. The model was demonstrated to exhibit a high degree of predictive power as documented by a good agreement between predictions and measurements, and it is deemed well suited for simulations of thermomechanical processing of Al-Mg-Si alloys where plastic deformation is carried out at various strain rates and temperatures.

  5. Closed-loop MBE growth of droplet-free GaN with very metal rich conditions using Metal Modulated Epitaxy with Mg and In

    Energy Technology Data Exchange (ETDEWEB)

    Burnham, S.D.; Henderson, W.; Doolittle, W.A. [School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States)

    2008-07-01

    Improvements to the Metal Modulated Epitaxy (MME) technique are achieved through computer controlled shutter transitions based on feedback from RHEED transients (S. D. Burnham and W. A. Doolittle, J. Vac. Sci. Technol. B 24, 2100 (2006)), thus creating a closed-loop control system for nitride MBE, the first of its kind. A high-sensitivity 22 bit camera is used to determine when RHEED transients have subsided, upon which a shutter transition is initiated allowing the efficient buildup and depletion of the metal bilayer, which improves surface morphology and growth rate compared to the standard MME technique. RMS surface roughness was reduced by 41% by using this 'Smart Shuttering' improvement to MME. A substantially higher peak concentration of Mg, approaching 2% atomic concentration, was achieved using the MME technique. As expected, a negligible amount of In was incorporated into the very Ga-rich films. Using the new closed loop control system developed for MBE, the surface morphology was improved for GaN films while highly repeatable holes concentrations as high as 4.7 x 10{sup 18} cm{sup -3} with 1.07 cm{sup 2}/V-sec mobility was obtained. This approach offers great promise for improved reproducibility and improved material quality. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  6. Selective inhibition of MG-63 osteosarcoma cell proliferation induced by curcumin-loaded self-assembled arginine-rich-RGD nanospheres

    Directory of Open Access Journals (Sweden)

    Chang R

    2015-05-01

    cytotoxicity against MG-63 osteosarcoma cells when compared with normal osteoblasts. We have demonstrated for the first time that APNPs can encapsulate hydrophobic curcumin in their hydrophobic cores, and curcumin-loaded APNPs could be an innovative treatment for the selective inhibition of osteosarcoma cells. Keywords: osteosarcoma, selective inhibition, curcumin, arginine-rich, arginine-glycine-aspartic acid, self-assembly

  7. Selective inhibition of MG-63 osteosarcoma cell proliferation induced by curcumin-loaded self-assembled arginine-rich-RGD nanospheres.

    Science.gov (United States)

    Chang, Run; Sun, Linlin; Webster, Thomas J

    2015-01-01

    Osteosarcoma is the most frequent primary malignant form of bone cancer, comprising 30% of all bone cancer cases. The objective of this in vitro study was to develop a treatment against osteosarcoma with higher selectivity toward osteosarcoma cells and lower cytotoxicity toward normal healthy osteoblast cells. Curcumin (or diferuloylmethane) has been found to have antioxidant and anticancer effects by multiple cellular pathways. However, it has lower water solubility and a higher degradation rate in alkaline conditions. In this study, the amphiphilic peptide C18GR7RGDS was used as a curcumin carrier in aqueous solution. This peptide contains a hydrophobic aliphatic tail group leading to their self-assembly by hydrophobic interactions, as well as a hydrophilic head group composed of an arginine-rich and an arginine-glycine-aspartic acid structure. Through characterization by transmission electron microscopy, self-assembled structures of spherical amphiphilic nanoparticles (APNPs) with diameters of 10-20 nm in water and phosphate-buffered saline were observed, but this structure dissociated when the pH value was reduced to 4. Using a method of codissolution with acetic acid and dialysis tubing, the solubility of curcumin was enhanced and a homogeneous solution was formed in the presence of APNPs. Successful encapsulation of curcumin in APNPs was then confirmed by Fourier transform infrared and X-ray diffraction analyses. The cytotoxicity and cellular uptake of the APNP/curcumin complexes on both osteosarcoma and normal osteoblast cell lines were also evaluated by methyl-thiazolyl-tetrazolium assays and confocal fluorescence microscopy. The results showed that the curcumin-loaded APNPs had significant selective cytotoxicity against MG-63 osteosarcoma cells when compared with normal osteoblasts. We have demonstrated for the first time that APNPs can encapsulate hydrophobic curcumin in their hydrophobic cores, and curcumin-loaded APNPs could be an innovative treatment

  8. Produtividade e rendimento do cafeeiro nas cinco primeiras safras irrigado por pivô central em Lavras, MG Coffee yield and production during the initial five harvests under irrigation with center pivot in Lavras, MG

    Directory of Open Access Journals (Sweden)

    Luiz Antônio Lima

    2008-12-01

    foi de 225,6 sc e a média anual de 45,12 sc ha-1, com acréscimo de 119% na produtividade do cafeeiro quando comparada ao tratamento não irrigado, que produziu, em média, 24 sc ha-1 ano-1. O grau de maturação, no momento da colheita, influenciou o rendimento dos tratamentos, sendo os frutos nos estádios cereja e seco, os que mais interferiram no rendimento.Search for sustainability on agricultural exploration and incorporation of new technologies impose the necessity for knowledge and management of main factors related to production, such as irrigation. This experiment evaluated the irrigation effect on yield and production efficiency (amount of beans to produce a bag of 60Kg of coffee irrigated by center pivot in Lavras-MG, Brazil. The experiment was planted with the cultivar Rubi MG-1192, planted on March, 1999. spaced 3.5 meters between rows and 0.8 meters between plants. The experimental design was the one of randomized blocks, with six treatment levels and three replicates. The irrigation was applied at intervals of 2 or 3 days, on Mondays, Wednesdays and Fridays, based on the amount estimated by the water blance considering the class A pan evaporation (ECA and rain depths. The irrigation was calculated as 0% of the difference between ECA and rain depth - 0% ECA (T1, non irrigated, 60% ECA (T2, 80% ECA (T3, 100% ECA (T4, 120% ECA (T5 and 140% ECA (T6. After harvesting the coffee grains from the experimental plots, coffee samples were packed in ventilated plastic bags and dried on wood benches exposed to air long enough to decrease its moisture content between 11 and 12%, gravimetric water content. After drying, the beans were unpeeled and weighed to calculate the yield and production efficiency. Irrigation increased the yield of irrigated plots compared to non irrigated. Although non significant difference was statistically observed when comparing annual yields, the differences were statistically significant when the total production was compared among

  9. Sowing time on Soybean yield potential in Uberlândia-MGÉpoca de semeadura no Potencial produtivo de Soja em Uberlândia-MG

    Directory of Open Access Journals (Sweden)

    Cristina Divina Lemes Hamawaki

    2011-12-01

    Full Text Available The work was done in Uberlândia (MG to evaluate the performance of seven soybeans cultivars sowed in four different times: October 30th, November 15th, December 14th and 31st during the 2001/2002 season. The cultivars utilized were: DM-118 early-maturing, DM-247, DM-Victoria, DM-339, medium late cycle and DM-309, DM-98C81 and DM-Noble cycle Late. The statistical design was a randomized blocks in a factorial scheme (7 cultivars x 4 times with three replications. The evaluated characteristics were: yield, number of days for flowering, number of days for maturing, plant height, first bean height and plant laying. For the most evaluated cultivars, sowing beyond December 14th in Uberlandia region presented yield losses for earlier cultivars as DM-118 as well for the later ones as DM Vitória, compared to sowing in 30th October. The time for flowering and maturing and plant height had effect on the yield.O trabalho foi feito em Uberlândia, com o objetivo de avaliar o comportamento de sete cultivares de soja em quatro épocas distintas de semeadura: 30 de Outubro, 15 de Novembro, 14 e 31 de Dezembro, na safra 2001/02. As cultivares utilizadas foram: DM-118 de ciclo precoce, DM-247, DM-Vitória, DM-339, de ciclo semitardio e DM-309, DM-98C81 e DM-Nobre de ciclo tardio. O delineamento utilizado foi o de blocos casualizados em esquema fatorial (7 cultivares x 4 épocas com três repetições. As características avaliadas foram: produtividade, número de dias para floração e maturação, altura de plantas na maturação, inserção da primeira vagem e acamamento. Para a maioria das cultivares, a semeadura realizada a partir de 14 de dezembro na região de Uberlândia provocou queda na produtividade, tanto para as cultivares mais precoces quanto para mais tardia, DM Vitória, quando comparada a semeadura em 30 de outubro. O período para o florescimento, maturação e a altura de plantas interferiram na produtividade. Há decréscimo de altura de

  10. Occurrence of Fe-Mg-rich smectites and corrensite in the Morron de Mateo bentonite deposit (Cabo de Gata region, Spain): A natural analogue of the bentonite barrier in a radwaste repository

    Energy Technology Data Exchange (ETDEWEB)

    Pelayo, M., E-mail: m.pelayo@ciemat.es [Departamento de Medio Ambiente, CIEMAT, Avda. Complutense 22, 28040 Madrid (Spain); Garcia-Romero, E. [Departamento de Cristalografia y Mineralogia, Facultad C.C. Geologicas, UCM, 28040 Madrid (Spain); Labajo, M.A.; Perez del Villar, L. [Departamento de Medio Ambiente, CIEMAT, Avda. Complutense 22, 28040 Madrid (Spain)

    2011-07-15

    Highlights: > A hydrothermal process transformed Fe-Mg smectites into corrensite. > This transformation was favoured by the intrusion of the Morron de Mateo dome. > The intrusion caused a temperature increased and a supply of Fe-Mg rich solutions. > The system can be a good natural analogue of bentonite barrier in a radwaste disposal. > Experimental studies of stability of bentonite are in agreement with the results. - Abstract: The Morron de Mateo bentonite deposit is being studied as a natural analogue of the thermal and geochemical effects on a bentonite barrier in a deep geological repository of high level radioactive wastes. This bentonite deposit and its host rocks were intruded by a rhyodacitic volcanic dome that induced a hydrothermal metasomatic process affecting the biocalcarenite beds close to the dome. In this work, the mineralogical and chemical features of the clay minerals of the hydrothermally altered pyroclastic (white tuffs) and epiclastic rocks (mass flow), located in the NE sector of the Morron de Mateo deposit are described. White tuffs have a high content of phyllosilicates, mainly composed of dioctahedral smectites, while mass flow have a higher proportion of inherited minerals, the neoformed phyllosilicates are dioctahedral smectites and an interlayer chlorite/smectite mineral of corrensite type. The chemical composition of smectites reflects the different nature of the parent rocks, in such a way that smectites from white tuffs have a quite homogeneous chemical composition and their structural formulae correspond to montmorillonite type, while smectites from mass flow show more chemical variability, higher Fe and Mg contents and a mean structural formulae corresponding to Fe-Mg-rich beidellite and/or to an intermediate smectite member between beidellite and saponite. In addition, chemical composition and textural features of corrensite-like clay minerals in relation to Fe-Mg-rich smectites in the samples have also been studied, suggesting

  11. Occurrence of Fe-Mg-rich smectites and corrensite in the Morron de Mateo bentonite deposit (Cabo de Gata region, Spain): A natural analogue of the bentonite barrier in a radwaste repository

    International Nuclear Information System (INIS)

    Pelayo, M.; Garcia-Romero, E.; Labajo, M.A.; Perez del Villar, L.

    2011-01-01

    Highlights: → A hydrothermal process transformed Fe-Mg smectites into corrensite. → This transformation was favoured by the intrusion of the Morron de Mateo dome. → The intrusion caused a temperature increased and a supply of Fe-Mg rich solutions. → The system can be a good natural analogue of bentonite barrier in a radwaste disposal. → Experimental studies of stability of bentonite are in agreement with the results. - Abstract: The Morron de Mateo bentonite deposit is being studied as a natural analogue of the thermal and geochemical effects on a bentonite barrier in a deep geological repository of high level radioactive wastes. This bentonite deposit and its host rocks were intruded by a rhyodacitic volcanic dome that induced a hydrothermal metasomatic process affecting the biocalcarenite beds close to the dome. In this work, the mineralogical and chemical features of the clay minerals of the hydrothermally altered pyroclastic (white tuffs) and epiclastic rocks (mass flow), located in the NE sector of the Morron de Mateo deposit are described. White tuffs have a high content of phyllosilicates, mainly composed of dioctahedral smectites, while mass flow have a higher proportion of inherited minerals, the neoformed phyllosilicates are dioctahedral smectites and an interlayer chlorite/smectite mineral of corrensite type. The chemical composition of smectites reflects the different nature of the parent rocks, in such a way that smectites from white tuffs have a quite homogeneous chemical composition and their structural formulae correspond to montmorillonite type, while smectites from mass flow show more chemical variability, higher Fe and Mg contents and a mean structural formulae corresponding to Fe-Mg-rich beidellite and/or to an intermediate smectite member between beidellite and saponite. In addition, chemical composition and textural features of corrensite-like clay minerals in relation to Fe-Mg-rich smectites in the samples have also been studied

  12. Magnesium-rich intermetallics RE3RuMg7 (RE = Y, Nd, Dy, Ho). Rows of condensed Ru rate at RE6/2 octahedra in magnesium matrices

    International Nuclear Information System (INIS)

    Kersting, Marcel; Rodewald, Ute C.; Schwickert, Christian; Poettgen, Rainer

    2013-01-01

    The magnesium-rich intermetallic phases RE 3 RuMg 7 (RE = Y, Nd, Dy, Ho) have been synthesized from the elements in sealed niobium ampoules and subsequently characterized by powder X-ray diffraction. The structure of the dysprosium compound was refined on the basis of single-crystal X-ray diffractometer data: Ti 6 Sn 5 type, P6 3 /mmc, a = 1019.1(2), c = 606.76(9) pm, wR2 = 0.0159, 439 F 2 values, 19 variables. The Mg3 site shows a small degree of Mg3/Dy mixing, leading to the composition Dy 3.03 RuMg 6.97 for the investigated crystal. The striking structural motifs in the Dy 3 RuMg 7 structure are rows of face-sharing Ru rate at Dy 6 octahedra and corner-sharing Mg2 rate at Mg 8 Dy 4 icosahedra. The rows of octahedra form a hexagonal rod-packing, and each rod is enrolled by six rows of the condensed icosahedra. Temperature-dependent magnetic susceptibility measurements of Dy 3 RuMg 7 show Curie-Weiss behavior with an experimental magnetic moment of 10.66(1) μ B per Dy atom. Antiferromagnetic ordering is detected at T N = 27.5(5) K. The 5 K isotherm shows a metamagnetic transition at a critical field of H C = 40 kOe. (orig.)

  13. Synthesize and electrochemical characterization of Mg-doped Li-rich layered Li[Li0.2Ni0.2Mn0.6]O2 cathode material

    International Nuclear Information System (INIS)

    Wang, Dan; Huang, Yan; Huo, Zhenqing; Chen, Li

    2013-01-01

    Highlights: • Layered Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 (2x = 0, 0.01, 0.02, 0.05) were synthetized. • Li[Li 0.2 Ni 0.2−x Mn 0.6−x Mg 2x ]O 2 exhibit enhanced electrochemical properties. • The improved performance is attributed to enhanced structure stability. -- Abstract: Mg-doped Li[Li 0.2 Ni 0.2 Mn 0.6 ]O 2 as a Li-rich cathode material of lithium-ion batteries were prepared by co-precipitation method and ball-milling treatment using Mg(OH) 2 as a dopant. Scanning electron microscopy (SEM), ex situ X-ray powder diffraction (XRD), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvantatic charge/discharge were used to investigate the effect of Mg doping on structure and electrochemical performance. Compared with the bare material, Mg-doped materials exhibit better cycle stabilities and superior rate capabilities. Li[Li 0.2 Ni 0.195 Mn 0.595 Mg 0.01 ]O 2 displays a high reversible capacity of 226.5 mAh g −1 after 60 cycles at 0.1 C. The excellent cycle performance can be attributed to the improvement in structure stability, which is verified by XRD tests before and after 60 cycles. EIS results show that Mg doping decreases the charge-transfer resistance and enhances the reaction kinetics, which is considered to be the major factor for higher rate performance

  14. Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

    International Nuclear Information System (INIS)

    Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

    2004-01-01

    Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

  15. Effect of Mn and Fe on the Formation of Fe- and Mn-Rich Intermetallics in Al-5Mg-Mn Alloys Solidified Under Near-Rapid Cooling.

    Science.gov (United States)

    Liu, Yulin; Huang, Gaoren; Sun, Yimeng; Zhang, Li; Huang, Zhenwei; Wang, Jijie; Liu, Chunzhong

    2016-01-29

    Mn was an important alloying element used in Al-Mg-Mn alloys. However, it had to be limited to a low level (Al-5Mg-Mn alloy with low Fe content (Al₆(Fe,Mn) was small in size and amount. With increasing Mn content, intermetallic Al₆(Fe,Mn) increased, but in limited amount. In high-Fe-containing Al-5Mg-Mn alloys (0.5 wt % Fe), intermetallic Al₆(Fe,Mn) became the dominant phase, even in the alloy with low Mn content (0.39 wt %). Cooling rate played a critical role in the refinement of the intermetallics. Under near-rapid cooling, intermetallic Al₆(Fe,Mn) was extremely refined. Even in the high Mn and/or high-Fe-containing alloys, it still demonstrated fine Chinese script structures. However, once the alloy composition passed beyond the eutectic point, the primary intermetallic Al₆(Fe,Mn) phase displayed extremely coarse platelet-like morphology. Increasing the content of Fe caused intermetallic Al₆(Fe,Mn) to become the primary phase at a lower Mn content.

  16. Ground state properties of neutron-rich Mg isotopes the "island of inversion" studied with laser and $\\beta$-NMR spectroscopy

    CERN Document Server

    Kowalska, M

    2006-01-01

    Studies in regions of the nuclear chart in which the model predictions of properties of nuclei fail can bring a better understanding of the strong interaction in the nuclear medium. To such regions belongs the so called "island of inversion" centered around Ne, Na and Mg isotopes with 20 neutrons in which unexpected ground-state spins, large deformations and dense low-energy spectra appear. This is a strong argument that the magic N=20 is not a closed shell in this area. In this thesis investigations of isotope shifts of stable $^{24-26}$Mg, as well as spins and magnetic moments of short-lived $^{29,31}$Mg are presented. The successful studies were performed at the ISOLDE facility at CERN using collinear laser and $\\beta$-NMR spectroscopy techniques. The isotopes were investigated as single-charged ions in the 280 nm transition from the atomic ground state $^2\\!$S$_{1/2}$ to one of the two lowest excited states $^2\\!$P$_{1/2 ,\\,3/2}$ using continuous wave laser beams. The isotope-shift measurements with fluor...

  17. Mineralogy and geochemistry of Zn-rich mine-drainage precipitates from an MgO passive treatment system by synchrotron-based X-ray analysis.

    Science.gov (United States)

    Pérez-López, Rafael; Macías, Francisco; Caraballo, Manuel A; Nieto, José Miguel; Román-Ross, Gabriela; Tucoulou, Rémi; Ayora, Carlos

    2011-09-15

    Synchrotron radiation-induced micro-X-ray analysis were applied to characterize the newly formed phases that precipitate in a passive treatment system using magnesium oxide to remove high concentrations of zinc (ca. 440 mg/L) and other minor metals from neutral pretreated waters in the Iberian Pyrite Belt (SW Iberian Peninsula). Micro-X-ray fluorescence (μ-XRF) maps of polished samples were used to find spatial correlations among metals, pinpointing zones of interest where micro-X-ray diffraction (μ-XRD) data were exploited to identify the mineral phases responsible for metal retention. This coupled technique identified hydrozincite (Zn(5)(CO(3))(2)(OH)(6)) and minor loseyite ((Mn,Zn)(7)(CO(3))(2)(OH)(10)) as the mineral sinks for Zn and also other potentially toxic elements such as Co and Ni. Although hydrozincite retains traces of Mn, this metal is mainly retained by precipitation of loseyite. The precipitation of zinc hydroxy-carbonates and their ability to uptake other metals (Mn, Co, and Ni) is hence of potential interest not only for the treatment of contaminated waters but also for the generation of a solid waste that could be exploited as a new Zn economic resource.

  18. Discovery of Ni-smectite-rich saprolite at Loma Ortega, Falcondo mining district (Dominican Republic): geochemistry and mineralogy of an unusual case of "hybrid hydrous Mg silicate - clay silicate" type Ni-laterite

    Science.gov (United States)

    Tauler, Esperança; Lewis, John F.; Villanova-de-Benavent, Cristina; Aiglsperger, Thomas; Proenza, Joaquín A.; Domènech, Cristina; Gallardo, Tamara; Longo, Francisco; Galí, Salvador

    2017-10-01

    Hydrous Mg silicate-type Ni-laterite deposits, like those in the Falcondo district, Dominican Republic, are dominated by Ni-enriched serpentine and garnierite. Recently, abundant Ni-smectite in the saprolite zone have been discovered in Loma Ortega, one of the nine Ni-laterite deposits in Falcondo. A first detailed study on these Ni-smectites has been performed (μXRD, SEM, EPMA), in addition to a geochemical and mineralogical characterisation of the Loma Ortega profile (XRF, ICP-MS, XRD). Unlike other smectite occurrences in laterite profiles worldwide, the Loma Ortega smectites are trioctahedral and exhibit high Ni contents never reported before. These Ni-smectites may be formed from weathering of pyroxene and olivine, and their composition can be explained by the mineralogy and the composition of the Al-depleted, olivine-rich parent ultramafic rock. Our study shows that Ni-laterites are mineralogically complex, and that a hydrous Mg silicate ore and a clay silicate ore can be confined to the same horizon in the weathering profile, which has significant implications from a recovery perspective. In accordance, the classification of "hybrid hydrous Mg silicate - clay silicate" type Ni-laterite deposit for Loma Ortega would be more appropriate.

  19. Study of Beta-Delayed Neutron Emission by Neutron-Rich Nuclei and Analysis of the Nuclear Reaction Mechanism responsible for the Yields of these Nuclei

    International Nuclear Information System (INIS)

    Bazin, D.

    1987-07-01

    Among the nuclear mechanisms used for the production of nuclei far from stability, the projectile fragmentation process has recently proved its efficiency. However, at Fermi energies, one has to take into account some collective and relaxation effects which drastically modify the production cross-sections. The spectroscopic study of very neutron-rich nuclei is very dependent of these production rates. A study of beta-delayed neutron emission which leads to new measurements of half-lives and neutron delayed emission probabilities is achieved with a liquid scintillator detector. The results which are then compared to different theories are of interest for the understanding of natural production of heavy elements (r processus) [fr

  20. A rich fossil record yields calibrated phylogeny for Acanthaceae (Lamiales) and evidence for marked biases in timing and directionality of intercontinental disjunctions.

    Science.gov (United States)

    Tripp, Erin A; McDade, Lucinda A

    2014-09-01

    More than a decade of phylogenetic research has yielded a well-sampled, strongly supported hypothesis of relationships within the large ( > 4000 species) plant family Acanthaceae. This hypothesis points to intriguing biogeographic patterns and asymmetries in sister clade diversity but, absent a time-calibrated estimate for this evolutionary history, these patterns have remained unexplored. Here, we reconstruct divergence times within Acanthaceae using fossils as calibration points and experimenting with both fossil selection and effects of invoking a maximum age prior related to the origin of Eudicots. Contrary to earlier reports of a paucity of fossils of Lamiales (an order of ∼ 23,000 species that includes Acanthaceae) and to the expectation that a largely herbaceous to soft-wooded and tropical lineage would have few fossils, we recovered 51 reports of fossil Acanthaceae. Rigorous evaluation of these for accurate identification, quality of age assessment and utility in dating yielded eight fossils judged to merit inclusion in analyses. With nearly 10 kb of DNA sequence data, we used two sets of fossils as constraints to reconstruct divergence times. We demonstrate differences in age estimates depending on fossil selection and that enforcement of maximum age priors substantially alters estimated clade ages, especially in analyses that utilize a smaller rather than larger set of fossils. Our results suggest that long-distance dispersal events explain present-day distributions better than do Gondwanan or northern land bridge hypotheses. This biogeographical conclusion is for the most part robust to alternative calibration schemes. Our data support a minimum of 13 Old World (OW) to New World (NW) dispersal events but, intriguingly, only one in the reverse direction. Eleven of these 13 were among Acanthaceae s.s., which comprises > 90% of species diversity in the family. Remarkably, if minimum age estimates approximate true history, these 11 events occurred within

  1. Do the rich always become richer? Characterizing the leaf physiological response of the high-yielding rice cultivar Takanari to free-air CO2 enrichment.

    Science.gov (United States)

    Chen, Charles P; Sakai, Hidemitsu; Tokida, Takeshi; Usui, Yasuhiro; Nakamura, Hirofumi; Hasegawa, Toshihiro

    2014-02-01

    The development of crops which are well suited to growth under future environmental conditions such as higher atmospheric CO2 concentrations ([CO2]) is essential to meeting the challenge of ensuring food security in the face of the growing human population and changing climate. A high-yielding indica rice variety (Oryza sativa L. cv. Takanari) has been recently identified as a potential candidate for such breeding, due to its high productivity in present [CO2]. To test if it could further increase its productivity under elevated [CO2] (eCO2), Takanari was grown in the paddy field under season-long free-air CO2 enrichment (FACE, approximately 200 µmol mol(-1) above ambient [CO2]) and its leaf physiology was compared with the representative japonica variety 'Koshihikari'. Takanari showed consistently higher midday photosynthesis and stomatal conductance than Koshihikari under both ambient and FACE growth conditions over 2 years. Maximum ribulose-1,5-bisphosphate carboxylation and electron transport rates were higher for Takanari at the mid-grain filling stage in both years. Mesophyll conductance was higher in Takanari than in Koshihikari at the late grain-filling stage. In contrast to Koshihikari, Takanari grown under FACE conditions showed no decrease in total leaf nitrogen on an area basis relative to ambient-grown plants. Chl content was higher in Takanari than in Koshihikari at the same leaf nitrogen level. These results indicate that Takanari maintains its superiority over Koshihikari in regards to its leaf-level productivity when grown in elevated [CO2] and it may be a valuable resource for rice breeding programs which seek to increase crop productivity under current and future [CO2].

  2. Produção e composição química da Brachiaria brizantha cv. MG-4 sob efeito de adubação com NPK = Yield and chemical composition of Brachiaria brizantha cv. MG-4 under the effect of NPK fertilization

    Directory of Open Access Journals (Sweden)

    Thaisa Grazielle Radin Magalhães Teles

    2011-04-01

    Full Text Available O objetivo deste trabalho foi avaliar os efeitos de combinações de doses de nitrogênio, fósforo e potássio sobre a produção de matéria seca e composição química de Brachiaria brizantha cv. MG-4. O experimento foi composto por 16 tratamentos de NPK, conforme matriz experimental Plan Puebla II, distribuídos em delineamento inteiramentecasualizado com cinco repetições. Utilizou-se um Argissolo Vermelho-Amarelo Distrófico Arênico e, como fonte de N, P e K, foram utilizados sulfato de amônio e uréia, superfosfato triplo e cloreto de potássio, respectivamente. O material coletado foi separado em colmo e folha, e pré-seco para a determinação da produção matéria seca de folhas (MSF, colmos (MSC e total (MST, teor de proteína bruta (PB, N, P e K. A adubação promoveu incremento na produção da B. brizantha cv. MG-4, cujas doses de 360-370-360 g vaso-1 de NPK, respectivamente, proporcionaram 95% da maior produção de MST observada. As produtividades máximas foram nas doses de 373, 407 e 317 mg dm-3 de N de solo para MST, MSF e MSC, respectivamente. As doses de N proporcionaram incrementos nos teores de PB das folhas. As adubações fosfatada e nitrogenada proporcionaram aumento na quantidade acumulada de N, P e K na B. brizantha cv. MG-4.The objective of this work was to evaluate the effects of combinations of nitrogen (N, phosphorus (P and potassium (K on the dry matter yield and chemical composition of Brachiaria brizantha cv. MG-4. The experiment consisted of 16 combination levels of NPK, according to experimental matrix Plan Puebla II, in a completely randomized design with five replications. It used a dystrophic RedYellow Sand-Argisol; ammonium and urea sulfate, triple super phosphate and potassium chloride were used as sources of N, P and K, respectively. The harvested material was separated into leaves and stem and submitted to dry matter yield (DMY evaluations of the aerial part, crude protein (CP and determination of

  3. Observation of the new neutron-rich nuclei 29F, 35,36Mg, 38,39Al, 40,41Si, 43,44P, 45,46,47S, 46,47,48,49Cl and 49,50,51Ar by means of a 55 MeV/u 48Ca beam

    International Nuclear Information System (INIS)

    Guillemaud-Mueller, D.; Anne, R.; Penionzhkevich, Yu.Eh.

    1988-01-01

    Using magnetic separation and identification through time of flight and ΔE,E measurements, the new neutron-rich nuclei, 29 F, 35,36 Mg, 38,39 Al, 40,41 Si, 43,44 P, 45,46,47 S, 46,47,48,49 Cl, 49,50,51 Ar have been observed from interactions of 48 Ca beam of 55 MeV/u with tantalum targets

  4. Comparing predicted yield and yield stability of willow and Miscanthus across Denmark

    DEFF Research Database (Denmark)

    Larsen, Søren; Jaiswal, Deepak; Bentsen, Niclas Scott

    2016-01-01

    was 12.1 Mg DM ha−1 yr−1 for willow and 10.2 Mg DM ha−1 yr−1 for Miscanthus. Coefficent of variation as a measure for yield stability was poorest on the sandy soils of northern and western Jutland and the year-to-year variation in yield was greatest on these soils. Willow was predicted to outyield...... Miscanthus on poor, sandy soils whereas Miscanthus was higher yielding on clay-rich soils. The major driver of yield in both crops was variation in soil moisture, with radiation and precipitation exerting less influence. This is the first time these two major feedstocks for northern Europe have been compared....... The semi-mechanistic crop model BioCro was used to simulate the production of both short rotation coppice (SRC) willow and Miscanthus across Denmark. Predictions were made from high spatial resolution soil data and weather records across this area for 1990-2010. The potential average, rain-fed mean yield...

  5. Equity yields

    NARCIS (Netherlands)

    Vrugt, E.; van Binsbergen, J.H.; Koijen, R.S.J.; Hueskes, W.

    2013-01-01

    We study a new data set of dividend futures with maturities up to ten years across three world regions: the US, Europe, and Japan. We use these asset prices to construct equity yields, analogous to bond yields. We decompose the equity yields to obtain a term structure of expected dividend growth

  6. Translocação orgânica, produtividade e rendimento de óleo essencial de Mentha piperita L. cultivada em solução nutritiva com variação dos níveis de N, P, K e Mg Organic translocation, productivity and essential oil yield of Mentha piperita L. cultivated in nutrient solution with varying N, P, K and Mg levels

    Directory of Open Access Journals (Sweden)

    E.F.S. David

    2009-01-01

    relação às demais plantas. Todos esses índices indicam melhor produtividade das plantas submetidas ao tratamento 65%N/50%P/25%K/100%Mg, que também apresentaram rendimento de óleo essencial, em média, maior durante o ciclo. Conclui-se que a redução de 35% de N, 50% de P, 75% de K (65%N/50%P/25%K/100%Mg é indicada para o cultivo e extração de óleo essencial de M. piperita.This study aimed to evaluate organic translocation, physiologic indexes of growth analysis and essential oil yield of Mentha piperita L. cultivated in nutrient solution with varying levels of N, P, K and Mg. Thus, four treatments were evaluated: 50% N, P, K, 25% Mg; 50% N, P, K, Mg; 65% N, 50% P, 25% K, 100% Mg; and 100% N, P, K, Mg. Organic translocation was assessed through leaf mass ratio (LMR and dry matter distribution to the different organs. The physiologic indexes leaf area ratio (LAR, specific leaf area (SLA, net assimilation rate (NAR and relative growth rate (RGR, derived from growth analysis, were estimated using the software ANACRES, following the quadratic exponential fitting of leaf area and dry mass of leaves and total plant, relative to time. Essential oil yield was calculated as percentage after extraction from shoot using hydrodistillation. Plants subjected to the treatment with complete level of nutrients (100%N/P/K/Mg less efficiently exported organic material from the leaf and LMR showed slower decrease due to the longer retention of such material in its production site. Besides, those plants did not present higher productivity and NAR and RGR curves showed slower decrease. Plants subjected to the treatment with 65%N/50%P/25%K/100%Mg had adequate organic matter exportation from the leaves to the stem and petioles, as demonstrated by LMR and dry matter distribution to these organs. Also in these plants, LAR was higher at the initial development and lower at 94 DAT, indicating leaf shading as a result of growth, and SLA showed less variation during the cycle, reflecting

  7. Transformation of Mg-bearing amorphous calcium carbonate to Mg-calcite - In situ monitoring

    Science.gov (United States)

    Purgstaller, Bettina; Mavromatis, Vasileios; Immenhauser, Adrian; Dietzel, Martin

    2016-02-01

    The formation of Mg-bearing calcite via an amorphous precursor is a poorly understood process that is of relevance for biogenic and abiogenic carbonate precipitation. In order to gain an improved insight on the controls of Mg incorporation in calcite formed via an Mg-rich amorphous calcium carbonate (Mg-ACC) precursor, the precipitation of Mg-ACC and its transformation to Mg-calcite was monitored by in situ Raman spectroscopy. The experiments were performed at 25.0 ± 0.03 °C and pH 8.3 ± 0.1 and revealed two distinct pathways of Mg-calcite formation: (i) At initial aqueous Mg/Ca molar ratios ⩽ 1:6, Mg-calcite formation occurs via direct precipitation from solution. (ii) Conversely, at higher initial Mg/Ca molar ratios, Mg-calcite forms via an intermediate Mg-rich ACC phase. In the latter case, the final product is a calcite with up to 20 mol% Mg. This Mg content is significant higher than that of the Mg-rich ACC precursor phase. Thus, a strong net uptake of Mg ions from the solution into the crystalline precipitate throughout and also subsequent to ACC transformation is postulated. Moreover, the temporal evolution of the geochemical composition of the reactive solution and the Mg-ACC has no significant effect on the obtained ;solubility product; of Mg-ACC. The enrichment of Mg in calcite throughout and subsequent to Mg-ACC transformation is likely affected by the high aqueous Mg/Ca ratio and carbonate alkalinity concentrations in the reactive solution. The experimental results have a bearing on the formation mechanism of Mg-rich calcites in marine early diagenetic environments, where high carbonate alkalinity concentrations are the rule rather than the exception, and on the insufficiently investigated inorganic component of biomineralisation pathways in many calcite secreting organisms.

  8. The CBM RICH project

    Energy Technology Data Exchange (ETDEWEB)

    Adamczewski-Musch, J. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Akishin, P. [Laboratory of Information Technologies, Joint Institute for Nuclear research (JINR-LIT), Dubna (Russian Federation); Becker, K.-H. [Department of Physics, University of Wuppertal, D-42097 Wuppertal (Germany); Belogurov, S. [SSC RF ITEP, 117218 Moscow (Russian Federation); Bendarouach, J. [Institute of Physics II and Institute of Applied Physics, Justus Liebig University Giessen, D-35392 Giessen (Germany); Boldyreva, N. [National Research Centre “Kurchatov Institute” B.P. Konstantinov Petersburg Nuclear Physics Institute, 188300 Gatchina (Russian Federation); Chernogorov, A. [SSC RF ITEP, 117218 Moscow (Russian Federation); Deveaux, C. [Institute of Physics II and Institute of Applied Physics, Justus Liebig University Giessen, D-35392 Giessen (Germany); Dobyrn, V. [National Research Centre “Kurchatov Institute” B.P. Konstantinov Petersburg Nuclear Physics Institute, 188300 Gatchina (Russian Federation); Dürr, M. [Institute of Physics II and Institute of Applied Physics, Justus Liebig University Giessen, D-35392 Giessen (Germany); Eschke, J. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Förtsch, J. [Department of Physics, University of Wuppertal, D-42097 Wuppertal (Germany); Heep, J.; Höhne, C. [Institute of Physics II and Institute of Applied Physics, Justus Liebig University Giessen, D-35392 Giessen (Germany); Kampert, K.-H. [Department of Physics, University of Wuppertal, D-42097 Wuppertal (Germany); and others

    2017-02-11

    The CBM RICH detector is an integral component of the future CBM experiment at FAIR, providing efficient electron identification and pion suppression necessary for the measurement of rare dileptonic probes in heavy ion collisions. The RICH design is based on CO{sub 2} gas as radiator, a segmented spherical glass focussing mirror with Al+MgF{sub 2} reflective coating, and Multianode Photomultipliers for efficient Cherenkov photon detection. Hamamatsu H12700 MAPMTs have recently been selected as photon sensors, following an extensive sensor evaluation, including irradiation tests to ensure sufficient radiation hardness of the MAPMTs. A brief overview of the detector design and concept is given, results on the radiation hardness of the photon sensors are shown, and the development of a FPGA-TDC based readout chain is discussed.

  9. Study of the neutron-rich nuclei with N=21, sup 3 sup 5 Si and sup 3 sup 3 Mg, by beta decay of sup 3 sup 5 Al and sup 3 sup 3 Na

    CERN Document Server

    Nummela, S; Caurier, E; Courtin, S; Dessagne, P; Holmlund, E; Jokinen, A; Knipper, A; Le Scornet, G; Mieh, C; Nowacki, F; Lyapin, L G; Oinonen, M; Poirier, E; Radivojevic, Z; Ramdhane, M; Trzaska, W H; Walter, G; Äystö, J

    2002-01-01

    The first information on the level structure of the N=21 nuclei, sup 3 sup 5 Si and sup 3 sup 3 Mg, has been obtained by the beta decay study of sup 3 sup 5 Al and sup 3 sup 3 Na, produced by fragmentation of an UC target with 1.4 GeV protons at CERN/ISOLDE. The experimental technique involved beta-gamma, beta-gamma-gamma, and beta-n-gamma coincidences, neutron spectra being obtained by time of flight measurements. Gamma detection was made either using large Ge counters or small BaF sub 2 scintillators (for lifetime measurements). In the case of the sup 3 sup 5 Al decay, (T sub 1 sub / sub 2 =41.6(2.2) ms), a simple structure has been found for the level scheme of sup 3 sup 5 Si (Z=14, N=21) which has been interpreted with the level sequence : 7/2 sup - , 3/2 sup - and 3/2 sup + corresponding respectively to the ground state and the states at 910 and 974 keV. The life-time of the 974 keV [T sub 1 sub / sub 2 =5.9(6) ns] is found consistent with the proposed level scheme and multipolarities. The investigation ...

  10. Produção e composição química da Brachiaria brizantha cv. MG-4 sob efeito de adubação com NPK - doi: 10.4025/actascianimsci.v33i2.9392 Yield and chemical composition of Brachiaria brizantha cv. MG-4 under the effect of NPK fertilization - doi: 10.4025/actascianimsci.v33i2.9392

    Directory of Open Access Journals (Sweden)

    Pedro Zione de Souza

    2011-04-01

    Full Text Available O objetivo deste trabalho foi avaliar os efeitos de combinações de doses de nitrogênio, fósforo e potássio sobre a produção de matéria seca e composição química de Brachiaria brizantha cv. MG-4. O experimento foi composto por 16 tratamentos de NPK, conforme matriz experimental Plan Puebla II, distribuídos em delineamento inteiramente casualizado com cinco repetições. Utilizou-se um Argissolo Vermelho-Amarelo Distrófico Arênico e, como fonte de N, P e K, foram utilizados sulfato de amônio e uréia, superfosfato triplo e cloreto de potássio, respectivamente. O material coletado foi separado em colmo e folha, e pré-seco para a determinação da produção matéria seca de folhas (MSF, colmos (MSC e total (MST, teor de proteína bruta (PB, N, P e K. A adubação promoveu incremento na produção da B. brizantha cv. MG-4, cujas doses de 360-370-360 g vaso-1 de NPK, respectivamente, proporcionaram 95% da maior produção de MST observada. As produtividades máximas foram nas doses de 373, 407 e 317 mg dm-3 de N de solo para MST, MSF e MSC, respectivamente. As doses de N proporcionaram incrementos nos teores de PB das folhas. As adubações fosfatada e nitrogenada proporcionaram aumento na quantidade acumulada de N, P e K na B. brizantha cv. MG-4.The objective of this work was to evaluate the effects of combinations of nitrogen (N, phosphorus (P and potassium (K on the dry matter yield and chemical composition of Brachiaria brizantha cv. MG-4. The experiment consisted of 16 combination levels of NPK, according to experimental matrix Plan Puebla II, in a completely randomized design with five replications. It used a dystrophic Red Yellow Sand-Argisol; ammonium and urea sulfate, triple super phosphate and potassium chloride were used as sources of N, P and K, respectively. The harvested material was separated into leaves and stem and submitted to dry matter yield (DMY evaluations of the aerial part, crude protein (CP and determination

  11. Correlation Analysis of some Growth, Yield, Yield Components and ...

    African Journals Online (AJOL)

    three critical growth stages which was imposed by withholding water (at ... November, 5th December, 19th December and 2nd January) laid out in a split ... Simple correlation coefficient ® of different crop parameters and grain yield ... The husk bran and germ are rich sources of ..... heat in 2009/2010 dry season at Fadam a ...

  12. Identification of four families of yCCR4- and Mg2+-dependent endonuclease-related proteins in higher eukaryotes, and characterization of orthologs of yCCR4 with a conserved leucine-rich repeat essential for hCAF1/hPOP2 binding

    Directory of Open Access Journals (Sweden)

    Corbo Laura

    2001-11-01

    Full Text Available Abstract Background The yeast yCCR4 factor belongs to the CCR4-NOT transcriptional regulatory complex, in which it interacts, through its leucine-rich repeat (LRR motif with yPOP2. Recently, yCCR4 was shown to be a component of the major cytoplasmic mRNA deadenylase complex, and to contain a fold related to the Mg2+-dependent endonuclease core. Results Here, we report the identification of nineteen yCCR4-related proteins in eukaryotes (including yeast, plants and animals, which all contain the yCCR4 endonuclease-like fold, with highly conserved CCR4-specific residues. Phylogenetic and genomic analyses show that they form four distinct families, one of which contains the yCCR4 orthologs. The orthologs in animals possess a leucine-rich repeat domain. We show, using two-hybrid and far-Western assays, that the human member binds to the human yPOP2 homologs, i.e. hCAF1 and hPOP2, in a LRR-dependent manner. Conclusions We have identified the mammalian orthologs of yCCR4 and have shown that the human member binds to the human yPOP2 homologs, thus strongly suggesting conservation of the CCR4-NOT complex from yeast to human. All members of the four identified yCCR4-related protein families show stricking conservation of the endonuclease-like catalytic motifs of the yCCR4 C-terminal domain and therefore constitute a new family of potential deadenylases in mammals.

  13. Crescimento , produção de matéria seca e acúmulo de N, P, K, Ca, Mg e S na parte aérea de mudas de andiroba (Carapa guianensis Aubl. cultivadas em solo de várzea, em função de diferentes doses de fósforo Growth, dry matter yield and N, P, K, Ca, Mg and S accumulation in andiroba seedling shoots (Carapa guianensis Aubl. cultivated in lowland soil, in function of phosphorus doses

    Directory of Open Access Journals (Sweden)

    Orlando Sílvio Caires Neves

    2004-06-01

    Full Text Available Com o objetivo de avaliar o efeito de diferentes doses de fósforo no crescimento e produção de matéria seca e acúmulo de N, P, K, Ca, Mg e S na parte aérea de mudas de andiroba, cultivadas em solo de várzea, foi conduzido um experimento em casa de vegetação, no Departamento de Ciências do Solo (DCS da Universidade Federal de Lavras (UFLA. O delineamento utilizado foi em blocos casualizados com cinco repetições e quatro doses de fósforo (0, 150, 300 e 450 mg dm-3 de P. Foram avaliados diâmetro do caule (mm, altura de plantas (cm, matéria seca de raiz, caule, folha e total (g planta-1. A partir dos teores dos elementos, determinou-se o acúmulo dos nutrientes com base na matéria seca. A máxima resposta física da planta de andiroba à adubação fosfatada foi obtida na faixa de 239 a 265 mg dm-3 de P. O máximo acúmulo de N, P, K, Ca, Mg e S foi atingido com as doses de 254; 287,5; 244,5; 254; 241; e 275 mg dm-3 de P, respectivamente. Os elementos em estudo que mais acumularam na parte aérea das mudas de andiroba seguem a seguinte ordem decrescente: N > Ca > K > Mg > S > P.To evaluate the effect of phosphorus application on growth, dry matter yield and N, P, K, Ca, Mg and S accumulation in "andiroba" seedling shoots, cultivated in lowland soil, an experiment was conducted under greenhouse conditions at the Soil Science Department (DCS of the Federal University of Lavras (UFLA. The experiment was conducted in a randomized block design, with five replications and four phosphorus doses (0, 150, 300 and 450 mg dm-3 of P. Stem diameter (mm, plant height (cm, root dry matter, stem, leafs and total (g plant-1 were evaluated and the accumulation of the nutrients based on dry matter was determined. The maximum physical response of andiroba to phosphorus was obtained between 239 to 265 mg dm-3 of P. The maximum accumulation of N, P, K, Ca, Mg and S was observed with the doses 254, 287,5, 244,5, 254, 241 and 275 mg dm-3 of P, respectively

  14. Redefining yield gaps at various spatial scales

    Science.gov (United States)

    Meng, K.; Fishman, R.; Norstrom, A. V.; Diekert, F. K.; Engstrom, G.; Gars, J.; McCarney, G. R.; Sjostedt, M.

    2013-12-01

    Recent research has highlighted the prevalence of 'yield gaps' around the world and the importance of closing them for global food security. However, the traditional concept of yield gap -defined as the difference between observed and optimal yield under biophysical conditions - omit relevant socio-economic and ecological constraints and thus offer limited guidance on potential policy interventions. This paper proposes alternative definitions of yield gaps by incorporating rich, high resolution, national and sub-national agricultural datasets. We examine feasible efforts to 'close yield gaps' at various spatial scales and across different socio-economic and ecological domains.

  15. The CAPRICE RICH detector

    Energy Technology Data Exchange (ETDEWEB)

    Basini, G. [INFN, Laboratori Nazionali di Frascati, Rome (Italy); Codino, A.; Grimani, C. [Perugia Univ. (Italy)]|[INFN, Perugia (Italy); De Pascale, M.P. [Rome Univ. `Tor Vergata` (Italy). Dip. di Fisica]|[INFN, Sezione Univ. `Tor Vergata` Rome (Italy); Cafagna, F. [Bari Univ. (Italy)]|[INFN, Bari (Italy); Golden, R.L. [New Mexico State Univ., Las Cruces, NM (United States). Particle Astrophysics Lab.; Brancaccio, F.; Bocciolini, M. [Florence Univ. (Italy)]|[INFN, Florence (Italy); Barbiellini, G.; Boezio, M. [Trieste Univ. (Italy)]|[INFN, Trieste (Italy)

    1995-09-01

    A compact RICH detector has been developed and used for particle identification in a balloon borne spectrometer to measure the flux of antimatter in the cosmic radiation. This is the first RICH detector ever used in space experiments that is capable of detecting unit charged particles, such as antiprotons. The RICH and all other detectors performed well during the 27 hours long flight.

  16. Cl-rich hydrous mafic mineral assemblages in the Highiș massif, Apuseni Mountains, Romania

    Science.gov (United States)

    Bonin, Bernard; Tatu, Mihai

    2016-08-01

    The Guadalupian (Mid-Permian) Highiș massif (Apuseni Mountains, Romania) displays a bimodal igneous suite of mafic (gabbro, diorite) and A-type felsic (alkali feldspar granite, albite granite, and hybrid granodiorite) rocks. Amphibole is widespread throughout the suite, and yields markedly high chlorine contents. Three groups are identified: Cl-rich potassic hastingsite (2.60-3.40 wt% Cl) within A-type felsic rocks and diorite, mildly Cl-rich pargasite to hornblende (0.80-1.90 wt% Cl) within gabbro, and low F-Cl hornblende within gabbro and hybrid granodiorite. Coexisting biotite is either Cl-rich within diorite, or F-Cl-poor to F-rich within A-type felsic rocks. Chlorine and fluorine are distributed in both mafic phases, according to the F-Fe and Cl-Mg avoidance rules. The low-Ti contents suggest subsolidus compositions. Cl-rich amphibole within diorite and A-type felsic rocks yields a restricted temperature range - from 575 °C down to 400 °C, whereas mildly Cl-rich amphibole within gabbro displays the highest range - from 675 to 360 °C. Temperatures recorded by Cl-rich biotite within diorite range from 590 to 410 °C. Biotite within A-type felsic rocks yields higher temperatures than amphibole: the highest values- from 640 to 540 °C - are recorded in low-F-Cl varieties, whereas the lowest values- from 535 to 500 °C - are displayed by F-rich varieties. All data point to halogen-rich hydrothermal fluids at upper greenschist facies conditions percolating through fractures and shear zones and pervasively permeating the whole Highiș massif, with F precipitating as interstitial fluorite and Cl incorporating into amphibole, during one, or possibly several, hydrothermal episodes that would have occurred during a ~ 150 My-long period of time extending from the Guadalupian (Mid-Permian) to the Albian (Mid-Cretaceous).

  17. Evaluation of an indicator for water yield in a watershed of Alto Rio Grande Region, State of Minas Gerais , Brazil Avaliação de um indicador de produção de água em uma bacia hidrográfica no Alto Rio Grande - MG

    Directory of Open Access Journals (Sweden)

    Roberto de Mattos

    2012-08-01

    Full Text Available The Brazilian Law stipulates that water is a limited natural resource doted of economic value, thus it is necessary to develop mechanisms for its adequate management. Actions that encourage the farmers to apply soil conservation practices with the purpose of increase water yield from springs and to promote improvement of its quality, reducing production of sediment transportation, is being encouraged by governments, even with financial compensation for owners. From these assertions, this study aims to quantify the benefits of the conservation actions of the management units and to characterize a Water Yield Indicator (WYI to support sustainable actions in the watershed of Alto Rio Grande region, in the state of Minas Gerais (MG. To assess the impact of actions it were identified four scenarios of land use and occupation of the watershed from Marcela stream which is located in Alto Rio Grande Region. After analyzing the results, it can be stated that the scenarios simulation has demonstrated important changes in water yield and that the definition of the Water Yield Index from the junction of the erosion potential with the water storage potential, has proved effective, as it integrate quantity and quality of water.A legislação brasileira estabelece que a água é um recurso natural limitado e dotado de valor econômico; logo, há necessidade de se criar mecanismos para sua adequada gestão. Medidas que estimulam os produtores rurais a adotarem práticas conservacionistas, visando a maior produção de água, melhoria de sua qualidade e redução da produção de sedimentos, vêm sendo estimuladas pelos governos, utilizando para isso até mesmo uma compensação financeira. A partir destas asserções, objetivou-se quantificar os benefícios das ações de conservação nas unidades de gestão e definir um Indicador de Produção de Água (IPA para a tomada de decisão em uma bacia hidrográfica da região Alto Rio Grande-MG. Para avaliar o

  18. Fungal endophytes from Acer ginnala Maxim: isolation, identification and their yield of gallic acid.

    Science.gov (United States)

    Qi, F-H; Jing, T-Z; Wang, Z-X; Zhan, Y-G

    2009-07-01

    The aim of the study was to isolate the endophytic fungi from Acer ginnala and screen isolates rich in gallic acid. After epiphytic sterilization, 145 fungal endophytes were isolated from the stem, annual twig and seed of Acer ginnala. The endophytes were grouped into ten different taxa, Phomopsis sp., Neurospora sp., Phoma sp., Epicoccum sp., Penicillium sp., Alternaria sp., Fusarium sp., Trichoderma sp., Cladosporium sp. and a species of Pleosporales Incertae Sedis, by their morphological traits and ITS-rDNA sequence analysis. The content and yield of gallic acid of 141 isolates were determined by HPLC. On average, the species of Pleosporales Incertae Sedis had the highest content and yield of gallic acid (13.28 mg g(-1) DW; 119.62 mg l(-1)), while Alternaria sp. had the lowest. Of 141 fungal endophytes from A. ginnala, Phomopsis sp. isolate SX10 showed both the highest content and the highest yield of gallic acid (29.25 mg g(-1) DW; 200.47 mg l(-1)). Endophytic fungi isolated from A. ginnala may be used as potential producers of gallic acid and other compounds with biological activities, or functioned as elicitors to produce natural compounds.

  19. Polysaccharide rich fractions from barks of Ximenia americana inhibit peripheral inflammatory nociception in mice Antinociceptive effect of Ximenia americana polysaccharide rich fractions

    Directory of Open Access Journals (Sweden)

    Kaira E.S. da Silva-Leite

    Full Text Available Abstract Ximenia americana L., Olacaceae, barks are utilized in folk medicine as analgesic and anti-inflammatory. The objective was to evaluate the toxicity and antinociceptive effect of polysaccharides rich fractions from X. americana barks. The fractions were obtained by extraction with NaOH, followed by precipitation with ethanol and fractionation by ion exchange chromatography. They were administered i.v. or p.o. before nociception tests (writhing, formalin, carragenan-induced hypernociception, hot plate, or during 14 days for toxicity assay. The total polysaccharides fraction (TPL-Xa: 8.1% yield presented 43% carbohydrate (21% uronic acid and resulted in two main fractions after chromatography (FI: 12%, FII: 22% yield. FII showed better homogeneity/purity, content of 44% carbohydrate, including 39% uronic acid, arabinose and galactose as major monosaccharides, and infrared spectra with peaks in carbohydrate range for COO- groups of uronic acid. TPL-Xa (10 mg/kg and FII (0.1 and 1 mg/kg presented inhibitory effect in behavior tests that evaluate nociception induced by chemical and mechanical, but not thermal stimuli. TPL-Xa did not alter parameters of systemic toxicity. In conclusion, polysaccharides rich fractions of X. americana barks inhibit peripheral inflammatory nociception, being well tolerated by animals.

  20. Investigation of the 24Mg(d, p)25Mg reaction

    NARCIS (Netherlands)

    Meurders, F.; Korte, G. de

    1975-01-01

    Abstract Proton angular distributions from the 24Mg(d, p)25Mg reaction at Ed = 12.0 MeV have been measured with a split-pole magnetic spectrograph for Ex < 6 MeV at an average resolution (FWHM) of 7 keV. New ln values have been determined for three levels. A DWBA analysis yielded spectroscopic

  1. Investigation of the 26Mg(d, p)27Mg reaction

    NARCIS (Netherlands)

    Meurders, F.; Steld, A. van der

    1974-01-01

    The angular distributions of 31 protons groups from the 26Mg(d, p)27Mg reaction have been measured at Ed = 12.0 MeV with a split-pole magnetic spectrograph. Excitation energies have been determined for 29 bound states. Three new levels have been found. A DWBA analysis yields ln values for 19 levels;

  2. Production of phenolic-rich bio-oil from catalytic fast pyrolysis of biomass using magnetic solid base catalyst

    International Nuclear Information System (INIS)

    Zhang, Zhi-bo; Lu, Qiang; Ye, Xiao-ning; Li, Wen-tao; Hu, Bin; Dong, Chang-qing

    2015-01-01

    Highlights: • Phenolic-rich bio-oil was selectively produced from catalytic fast pyrolysis of biomass using magnetic solid base catalyst. • The actual yield of twelve major phenolic compounds reached 43.9 mg/g. • The peak area% of all phenolics reached 68.5% at the catalyst-to-biomass ratio of 7. • The potassium phosphate/ferroferric oxide catalyst possessed promising recycling properties. - Abstract: A magnetic solid base catalyst (potassium phosphate/ferroferric oxide) was prepared and used for catalytic fast pyrolysis of poplar wood to selectively produce phenolic-rich bio-oil. Pyrolysis–gas chromatography/mass spectrometry experiments were conducted to investigate the effects of pyrolysis temperature and catalyst-to-biomass ratio on the product distribution. The actual yields of important pyrolytic products were quantitatively determined by the external standard method. Moreover, recycling experiments were performed to determine the re-utilization abilities of the catalyst. The results showed that the catalyst exhibited promising activity to selectively produce phenolic-rich bio-oil, due to its capability of promoting the decomposition of lignin to generate phenolic compounds and meanwhile inhibiting the devolatilization of holocellulose. The maximal phenolic yield was obtained at the pyrolysis temperature of 400 °C and catalyst-to-biomass ratio of 2. The concentration of the phenolic compounds increased monotonically along with the increasing of the catalyst-to-biomass ratio, with the peak area% value increasing from 28.1% in the non-catalytic process to as high as 68.5% at the catalyst-to-biomass ratio of 7. The maximal total actual yield of twelve quantified major phenolic compounds was 43.9 mg/g, compared with the value of 29.0 mg/g in the non-catalytic process. In addition, the catalyst could be easily recovered and possessed promising recycling properties.

  3. Research: Rags to Rags? Riches to Riches?

    Science.gov (United States)

    Bracey, Gerald W.

    2004-01-01

    Everyone has read about what might be called the "gold gap"--how the rich in this country are getting richer and controlling an ever-larger share of the nation's wealth. The Century Foundation has started publishing "Reality Check", a series of guides to campaign issues that sometimes finds gaps in these types of cherished delusions. The guides…

  4. A study on preparation and hydriding of β-Mg2Al3 and γ-Mg17Al12

    International Nuclear Information System (INIS)

    Hadi Suwarno

    2009-01-01

    The mechanism of the synthetic formation of β-Mg 2 Al 3 and γ-Mg 17 Al 12 has been studied. Mechanical alloying of Mg and Al powders with the atomic ratio of Mg:Al = 2:3 in toluene solution yields β-Mg 2 Al 3 compound after milling for 30 h. The γ-Mg 17 Al 12 can be formed by heating the β-Mg 2 Al 3 at 430°C under high vacuum. The measured hydrogen capacities of β-Mg 2 Al 3 and γ-Mg 17 Al 12 as hydride at 300°C are 3.2 and 4.9 wt%, respectively. Microstructure of the Mg-Al specimen shows that on hydriding at 300°C the polygonal shape of the γ-Mg 17 Al 12 changes into irregular shapes which are composed of γ-MgH 2 and Al. (author)

  5. Kings Today, Rich Tomorrow

    DEFF Research Database (Denmark)

    Fattoum, Asma

    2013-01-01

    This study investigates the King vs. Rich dilemma that founder-CEOs face at IPO. When undertaking IPO, founders face two options. They can either get rich, but then run the risk of losing the control over their firms; or they can remain kings by introducing defensive mechanisms, but this is likel...

  6. Developments on RICH detectors

    International Nuclear Information System (INIS)

    Besson, P.; Bourgeois, P.

    1996-01-01

    The RICH (ring imaging Cherenkov) detector which is dedicated to Cherenkov radiation detection is described. An improvement made by replacing photo sensible vapor with solid photocathode is studied. A RICH detector prototype with a CsI photocathode has been built in Saclay and used with Saturne. The first results are presented. (A.C.)

  7. Effects of limestone, N, K and Mg fertilizers on Mg absorption by oats and barley

    Energy Technology Data Exchange (ETDEWEB)

    Alston, A M

    1966-01-01

    Oats grown in a pot experiment on two sandy loams were sampled at four stages of growth. Neither KCl nor MgSO/sub 4/. 7H/sub 2/O had any effect on yield but % Mg and total Mg uptake were consistently decreased by applying K and increased by applying Mg. Ca(NO/sub 3/)/sub 2/ increased % Mg more than did (NH/sub 4/)/sub 2/SO/sub 4/, but yield and total Mg uptake were higher where (NH/sub 4/)/sub 2/SO/sub 4/ was applied. The effects of fertilizers were similar on both soils. The effects of applying (NH/sub 4/)/sub 2/SO/sub 4/ and NaNO/sub 2/ to the soil on % Mg in barley were compared in a field experiment on an acid loam to which several rates of limestone had been applied. Treatments had no effect on the % Mg in grain or straw at maturity. At four earlier stages of growth (NH/sub 4/)/sub 2/SO)/sub 4/ increased % Mg in the plants more than did NaNO/sub 2/. Limestone slightly increased % Mg. Nitrification of NH/sub 4/ in the soil was rapid.

  8. Detection of Mg spinel lithologies on central peak of crater ...

    Indian Academy of Sciences (India)

    identified Fe bearing Mg-spinel-rich rock types are defined by their strong 2-μm ... The Modified Gaussian Modeling (MGM) analysis ... study the deep crustal and/or upper mantle composition and may lead to a fresh ... Lunar surface; Mg-spinel; central peak; Theophilus; remote sensing. .... The explanation of these spec-.

  9. Nuclear shell effects in neutron-rich nuclei around N=20 and N=32,34

    CERN Document Server

    Seidlitz, M

    Nuclear shell effects in neutron-rich nuclei around N=20 and N=32,34 were studied by means of reduced transition probabilities, i.e. B(E2) and B(M1) values. To this end a series of Coulomb-excitation experiments, employing radioactive 31Mg and 29,30Na beams, as well as a precise lifetime experiment of excited states in 56Cr were performed. The collective properties of excited states of 31Mg were the subject of a Coulomb-excitation experiment at REX-ISOLDE, CERN, employing a radioactive 31Mg beam at a beam energy of 3.0 MeV/u. The beam intensity amounted to 3000 ions/s on average. The highly efficient MINIBALL setup was employed, consisting of eight HPGe cluster detectors for gamma-ray detection and a segmented Si-detector for coincident particle detection. The level scheme of 31Mg was extended. Spin and parity assignment of the observed 945 keV state yielded 5/2+ and its de-excitation is dominated by a strong collective M1 transition. Comparison of the transition probabilities of 30,31,32Mg establishes that f...

  10. Industrial production of MgH2 and its application

    International Nuclear Information System (INIS)

    Uesugi, H.; Sugiyama, T.; Nii, H.; Ito, T.; Nakatsugawa, I.

    2011-01-01

    Research highlights: → Tablet and powder Mg were hydrogenated in a 50 kg batch furnace based on thermal equilibrium method. → Compression of Mg tablet improved the hydrogenation yield. → Hydrolysis of MgH 2 using citric acid generated hydrogen under 373 K. → A MgH 2 -hydrogen reactor utilizing hydraulic head pressure was developed. → - Abstract: A process for the industrial production of magnesium hydride (MgH 2 ) based on a thermal equilibrium method and its application to portable hydrogen sources is proposed. Mg powders and tablets compressed with mechanically ground Mg ribbons were successfully hydrogenated in a 50-kg-batch furnace. The resultant MgH 2 showed a hydrogen yield of around 96% with good reproducibility. The compression ratio of Mg tablets was found to be an important factor in the hydrogenation yield. A hydrolysis technique using citric acid as an additive was employed to generate hydrogen under 373 K. Increasing the concentration of citric acid and the temperature accelerated the hydrolysis reactivity. A hydrogen reactor utilizing hydraulic head pressure was developed. It generated hydrogen continuously for 1 h at a flow rate of 100 ml min -1 with hydrolysis of 5 g of tablet-form MgH 2 . The conversion yield was around 70%, regardless of the flow rate.

  11. 6 Grain Yield

    African Journals Online (AJOL)

    create a favourable environment for rice ... developing lines adaptable to many ... have stable, not too short crop duration with ..... Analysis of variance of the effect of site and season on maturity, grain yield and plant ..... and yield components.

  12. The CBM RICH project

    Energy Technology Data Exchange (ETDEWEB)

    Adamczewski-Musch, J. [GSI Darmstadt (Germany); Becker, K.-H. [University Wuppertal (Germany); Belogurov, S. [ITEP Moscow (Russian Federation); Boldyreva, N. [PNPI Gatchina (Russian Federation); Chernogorov, A. [ITEP Moscow (Russian Federation); Deveaux, C. [University Gießen (Germany); Dobyrn, V. [PNPI Gatchina (Russian Federation); Dürr, M. [University Gießen (Germany); Eom, J. [Pusan National University (Korea, Republic of); Eschke, J. [GSI Darmstadt (Germany); Höhne, C. [University Gießen (Germany); Kampert, K.-H. [University Wuppertal (Germany); Kleipa, V. [GSI Darmstadt (Germany); Kochenda, L. [PNPI Gatchina (Russian Federation); Kolb, B. [GSI Darmstadt (Germany); Kopfer, J. [University Wuppertal (Germany); Kravtsov, P. [PNPI Gatchina (Russian Federation); Lebedev, S.; Lebedeva, E. [University Gießen (Germany); Leonova, E. [PNPI Gatchina (Russian Federation); and others

    2014-12-01

    The Compressed Baryonic Matter (CBM) experiment will study the properties of super dense nuclear matter by means of heavy ion collisions at the future FAIR facility. An integral detector component is a large Ring Imaging Cherenkov detector with CO{sub 2} gas radiator, which will mainly serve for electron identification and pion suppression necessary to access rare dileptonic probes like e{sup +}e{sup −} decays of light vector mesons or J/Ψ. We describe the design of this future RICH detector and focus on results obtained by building a CBM RICH detector prototype tested at CERN-PS.

  13. Yield stress fluids slowly yield to analysis

    NARCIS (Netherlands)

    Bonn, D.; Denn, M.M.

    2009-01-01

    We are surrounded in everyday life by yield stress fluids: materials that behave as solids under small stresses but flow like liquids beyond a critical stress. For example, paint must flow under the brush, but remain fixed in a vertical film despite the force of gravity. Food products (such as

  14. Neutron rich nuclei

    International Nuclear Information System (INIS)

    Foucher, R.

    1979-01-01

    If some β - emitters are particularly interesting to study in light, medium, and heavy nuclei, another (and also) difficult problem is to know systematically the properties of these neutron rich nuclei far from the stability line. A review of some of their characteristics is presented. How far is it possible to be objective in the interpretation of data is questioned and implications are discussed

  15. interrelationships between grain yield and other physiological traits

    African Journals Online (AJOL)

    Prof. Adipala Ekwamu

    Combined analysis of variance, cluster analysis and genotype-by- ... all phenological and morphological traits, except grain yield and associated yield components. ... egg, and other protein-rich foods (Alghali, 1991). ... systematic modelling approach. ... MD IT98 K -132 – 3 .... traits based on Principal Component axes (PC)1.

  16. Biofuels from pyrolysis in perspective: trade-offs between energy yields and soil-carbon additions.

    Science.gov (United States)

    Woolf, Dominic; Lehmann, Johannes; Fisher, Elizabeth M; Angenent, Largus T

    2014-06-03

    Coproduction of biofuels with biochar (the carbon-rich solid formed during biomass pyrolysis) can provide carbon-negative bioenergy if the biochar is sequestered in soil, where it can improve fertility and thus simultaneously address issues of food security, soil degradation, energy production, and climate change. However, increasing biochar production entails a reduction in bioenergy obtainable per unit biomass feedstock. Quantification of this trade-off for specific biochar-biofuel pathways has been hampered by lack of an accurate-yet-simple model for predicting yields, product compositions, and energy balances from biomass slow pyrolysis. An empirical model of biomass slow pyrolysis was developed and applied to several pathways for biochar coproduction with gaseous and liquid biofuels. Here, we show that biochar production reduces liquid biofuel yield by at least 21 GJ Mg(-1) C (biofuel energy sacrificed per unit mass of biochar C), with methanol synthesis giving this lowest energy penalty. For gaseous-biofuel production, the minimum energy penalty for biochar production is 33 GJ Mg(-1) C. These substitution rates correspond to a wide range of Pareto-optimal system configurations, implying considerable latitude to choose pyrolysis conditions to optimize for desired biochar properties or to modulate energy versus biochar yields in response to fluctuating price differentials for the two commodities.

  17. Bond yield curve construction

    Directory of Open Access Journals (Sweden)

    Kožul Nataša

    2014-01-01

    Full Text Available In the broadest sense, yield curve indicates the market's view of the evolution of interest rates over time. However, given that cost of borrowing it closely linked to creditworthiness (ability to repay, different yield curves will apply to different currencies, market sectors, or even individual issuers. As government borrowing is indicative of interest rate levels available to other market players in a particular country, and considering that bond issuance still remains the dominant form of sovereign debt, this paper describes yield curve construction using bonds. The relationship between zero-coupon yield, par yield and yield to maturity is given and their usage in determining curve discount factors is described. Their usage in deriving forward rates and pricing related derivative instruments is also discussed.

  18. Measurements of fission yields

    International Nuclear Information System (INIS)

    Denschlag, H.O.

    2000-01-01

    After some historical introductory remarks on the discovery of nuclear fission and early fission yield determinations, the present status of knowledge on fission yields is briefly reviewed. Practical and fundamental reasons motivating the pursuit of fission yield measurements in the coming century are pointed out. Recent results and novel techniques are described that promise to provide new interesting insights into the fission process during the next century. (author)

  19. Fission product yields

    International Nuclear Information System (INIS)

    Valenta, V.; Hep, J.

    1978-01-01

    Data are summed up necessary for determining the yields of individual fission products from different fissionable nuclides. Fractional independent yields, cumulative and isobaric yields are presented here for the thermal fission of 235 U, 239 Pu, 241 Pu and for fast fission (approximately 1 MeV) of 235 U, 238 U, 239 Pu, 241 Pu; these values are included into the 5th version of the YIELDS library, supplementing the BIBFP library. A comparison is made of experimental data and possible improvements of calculational methods are suggested. (author)

  20. Radiolytically depolymerized sodium alginate improves physiological activities, yield attributes and composition of essential oil of Eucalyptus citriodora Hook.

    Science.gov (United States)

    Ali, Akbar; Khan, M Masroor A; Uddin, Moin; Naeem, M; Idrees, Mohd; Hashmi, Nadeem; Dar, Tariq Ahmad; Varshney, Lalit

    2014-11-04

    Eucalyptus citriodora Hook. is highly valued for its citronellal-rich essential oil (EO) extracted from its leaves. Hence, escalated EO production of eucalyptus is the need of hour. Marine polysaccharides (sodium alginate) are processed through gamma radiation of particular intensity, to obtain the irradiated sodium alginate (ISA). A pot experiment was conducted to study the effect of foliar application of ISA on growth, biochemical, physiological, EO yield and composition of E. citriodora. The treatments were applied as: foliar spray of deionized water only (control), seed soaked with ISA (90 mg L(-1)) and foliar spray of ISA with 30, 60, 120 and 240 mg L(-1). The treatment 6 (spray of ISA at 120 mg L(-1)) showed the highest value for most of the parameters studied. It also enhanced the EO content (33.3%), EO yield (86.7%), citronellal content (63.4%) and citronellal yield (205.5%) as compared to the control. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. The CLEO RICH detector

    International Nuclear Information System (INIS)

    Artuso, M.; Ayad, R.; Bukin, K.; Efimov, A.; Boulahouache, C.; Dambasuren, E.; Kopp, S.; Li, Ji; Majumder, G.; Menaa, N.; Mountain, R.; Schuh, S.; Skwarnicki, T.; Stone, S.; Viehhauser, G.; Wang, J.C.; Coan, T.E.; Fadeyev, V.; Maravin, Y.; Volobouev, I.; Ye, J.; Anderson, S.; Kubota, Y.; Smith, A.

    2005-01-01

    We describe the design, construction and performance of a Ring Imaging Cherenkov Detector (RICH) constructed to identify charged particles in the CLEO experiment. Cherenkov radiation occurs in LiF crystals, both planar and ones with a novel 'sawtooth'-shaped exit surface. Photons in the wavelength interval 135-165nm are detected using multi-wire chambers filled with a mixture of methane gas and triethylamine vapor. Excellent π/K separation is demonstrated

  2. CBM RICH geometry optimization

    Energy Technology Data Exchange (ETDEWEB)

    Mahmoud, Tariq; Hoehne, Claudia [II. Physikalisches Institut, Giessen Univ. (Germany); Collaboration: CBM-Collaboration

    2016-07-01

    The Compressed Baryonic Matter (CBM) experiment at the future FAIR complex will investigate the phase diagram of strongly interacting matter at high baryon density and moderate temperatures in A+A collisions from 2-11 AGeV (SIS100) beam energy. The main electron identification detector in the CBM experiment will be a RICH detector with a CO{sub 2} gaseous-radiator, focusing spherical glass mirrors, and MAPMT photo-detectors being placed on a PMT-plane. The RICH detector is located directly behind the CBM dipole magnet. As the final magnet geometry is now available, some changes in the RICH geometry become necessary. In order to guarantee a magnetic field of 1 mT at maximum in the PMT plane for effective operation of the MAPMTs, two measures have to be taken: The PMT plane is moved outwards of the stray field by tilting the mirrors by 10 degrees and shielding boxes have been designed. In this contribution the results of the geometry optimization procedure are presented.

  3. Effect of different seawater Mg

    NARCIS (Netherlands)

    Mewes, A.; Langer, G.; de Nooijer, L.J.; Bijma, J.; Reichart, G.J.

    2014-01-01

    Magnesium, incorporated in foraminiferal calcite (Mg/CaCC), is used intensively to reconstruct past seawater temperatures but, in addition to temperature, the Mg/CaCC of foraminiferal tests also depends on the ratio of Mg and Ca in seawater (Mg/CaSW). The physiological mechanisms responsible for

  4. Sorption of selenium on Mg-Al and Mg-Al-Eu layered double hydroxides

    International Nuclear Information System (INIS)

    Curtius, H.; Paparigas, Z.; Kaiser, G.

    2008-01-01

    Salt domes represent deep geological formations which are under consideration as final repositories for irradiated research reactor fuel elements. For long-term safety aspects the mobilisation of the radionuclides due to a water ingress is intensively investigated. At the Institute of Energy Research (IEF-6), leaching experiments were performed in a hot cell facility with UAl x -Al and U 3 Si 2 -Al dispersed research reactor fuel elements in repository-relevant MgCl 2 -rich salt brines under anaerobic conditions. The fuel plates corroded completely within one year and a Mg-Al-layered double hydroxide (LDH) with chloride as interlayer anion was identified as one crystalline phase component of the corrosion products (secondary phases). This Mg-Al-LDH was synthesized, characterized, and the ability to retard europium by an incorporation process was investigated. Europium, as a representative for lanthanides, was identified to be one of the radionuclides which were found in the corrosion products. We could show that europium was incorporated in the lattice structure. LDHs have high anion exchange capacities that enhance their potential to remove anionic contaminants from aqueous systems. In this work the sorption behaviour of selenium in the chemical form as selenite (SeO 3 2- ) on Mg-Al-LDH and on Mg-Al-Eu-LDH was investigated. Especially the influence of the larger europium-III ion was of interest. It represents in the Mg-Al-Eu-LDH about 10% of the molar aluminium amount. The sorption has been experimentally studied in a wide range of pH, ionic strength, radionuclide and sorbent concentration. Both LDHs with chloride as interlayer anion were synthesized by a coprecipitation method under controlled conditions, and their main physico-chemical properties were analyzed prior to the sorption experiments. The sorption kinetics of selenite on the LDHs in water and in MgCl 2 -rich brine were rapid using a LDH concentration of 10 g/L. Equilibrium, indicated by stable p

  5. Excitation functions and yields for cyclotron production of radiorhenium via deuteron irradiation. {sup nat}W(d,xn){sup 181,182,(A+B),183,184(m+g),186g}Re nuclear reactions and tests on the production of {sup 186g}Re using enriched {sup 186}W

    Energy Technology Data Exchange (ETDEWEB)

    Manenti, Simone; Persico, Elisa; Bonardi, Mauro L.; Gini, Luigi; Groppi, Flavia [LASA, Univ. degli Studi di Milano, Segrate (Italy); INFN Milano (Italy); Abbas, Kamel; Holzwarth, Uwe; Simonelli, Federica [Institute for Health and Consumer Protection, IHCP, JRC-Ispra, Ispra (Italy)

    2014-10-01

    Excitation functions, thin- and thick-target yields for the {sup 181-186g}Re and {sup 187}W radionuclides were measured by the activation stacked-foil technique on natural tungsten foils for deuteron energies up to 18.0 MeV. These cross sections were validated by comparing the experimental results for thick-target yields with those calculated by integration of the thin-target yields. It was found that the maximum {sup 186g}Re content by irradiation of natural tungsten is about 55%, a higher value compared with the one found for proton beam, but not sufficient to use natural tungsten for medical purposes yet. Thus, in order to have a higher specific activity A{sub S} of {sup 186g}Re, the use of enriched {sup 186}W target is necessary. Therefore the irradiation of a thick target of enriched {sup 186}W by accelerated deuterons was studied and the results for the production of {sup 186g}Re were compared with those obtained from the irradiation of the same target by accelerated protons. It was found that the deuteron irradiation is preferable for three reasons: larger yield, less contamination by tantalum radioisotopes and smaller required amount of the target, which simplify the separation of the {sup 186g}Re from the target itself.

  6. Quantitative electron microscopy and spectroscopy of MgB2 wires and tapes

    International Nuclear Information System (INIS)

    Birajdar, B; Peranio, N; Eibl, O

    2008-01-01

    In MgB 2 the correlation of microstructure with superconducting properties, in particular the critical current density, requires powerful analytical tools. Critical current densities and electrical resistivities of different MgB 2 superconductors differ by orders of magnitudes and the current limiting mechanisms have not been fully understood. Granularity of MgB 2 is one significant reason for reduced critical current densities and is introduced intrinsically by the anisotropy of B c2 but also extrinsically by the microstructure of the material. B c2 enhancement by doping is another important challenge for chemical analysis and, at present, doping levels are not well controlled on the sub-μm scale. In this paper the quantitative electron microscopy and spectroscopy methods essential for the microstructural analysis of MgB 2 are described. By quantitative electron microscopy and spectroscopy we mean a combined SEM and TEM analysis that covers various length scales from μm to nm. Contamination-free sample preparation, chemical mapping including B, and advanced chemical quantification using x-ray microanalysis were essential elements of the applied methodology. The methodology was applied to in situ and ex situ MgB 2 wires and tapes with and without SiC additives. Quantitative B analysis by EDX spectroscopy was applied quantitatively in the SEM and TEM, which is a major achievement. Although MgB 2 is a binary system, the thermodynamics of phase formation is complex, and the complexity is dramatically increased if additives like SiC are used. The small, sub-μm grain sizes of the matrix and secondary phases require TEM methods. However, granularity on the μm scale was also identified and underlines the importance of the combined SEM and TEM studies. Significant differences in the microstructure were observed for in situ and ex situ samples. This holds particularly if SiC was added and yielded Mg 2 Si for in situ samples annealed at 600-650 deg. C and Mg-Si-O phases

  7. Stability Performance of Inductively Coupled Plasma Mass Spectrometry-Phenotyped Kernel Minerals Concentration and Grain Yield in Maize in Different Agro-Climatic Zones.

    Science.gov (United States)

    Mallikarjuna, Mallana Gowdra; Thirunavukkarasu, Nepolean; Hossain, Firoz; Bhat, Jayant S; Jha, Shailendra K; Rathore, Abhishek; Agrawal, Pawan Kumar; Pattanayak, Arunava; Reddy, Sokka S; Gularia, Satish Kumar; Singh, Anju Mahendru; Manjaiah, Kanchikeri Math; Gupta, Hari Shanker

    2015-01-01

    Deficiency of iron and zinc causes micronutrient malnutrition or hidden hunger, which severely affects ~25% of global population. Genetic biofortification of maize has emerged as cost effective and sustainable approach in addressing malnourishment of iron and zinc deficiency. Therefore, understanding the genetic variation and stability of kernel micronutrients and grain yield of the maize inbreds is a prerequisite in breeding micronutrient-rich high yielding hybrids to alleviate micronutrient malnutrition. We report here, the genetic variability and stability of the kernel micronutrients concentration and grain yield in a set of 50 maize inbred panel selected from the national and the international centres that were raised at six different maize growing regions of India. Phenotyping of kernels using inductively coupled plasma mass spectrometry (ICP-MS) revealed considerable variability for kernel minerals concentration (iron: 18.88 to 47.65 mg kg(-1); zinc: 5.41 to 30.85 mg kg(-1); manganese: 3.30 to 17.73 mg kg(-1); copper: 0.53 to 5.48 mg kg(-1)) and grain yield (826.6 to 5413 kg ha(-1)). Significant positive correlation was observed between kernel iron and zinc within (r = 0.37 to r = 0.52, p kernel minerals concentration and grain yield. Most of the variation was contributed by genotype main effect for kernel iron (39.6%), manganese (41.34%) and copper (41.12%), and environment main effects for both kernel zinc (40.5%) and grain yield (37.0%). Genotype main effect plus genotype-by-environment interaction (GGE) biplot identified several mega environments for kernel minerals and grain yield. Comparison of stability parameters revealed AMMI stability value (ASV) as the better representative of the AMMI stability parameters. Dynamic stability parameter GGE distance (GGED) showed strong and positive correlation with both mean kernel concentrations and grain yield. Inbreds (CM-501, SKV-775, HUZM-185) identified from the present investigation will be useful in

  8. Stability Performance of Inductively Coupled Plasma Mass Spectrometry-Phenotyped Kernel Minerals Concentration and Grain Yield in Maize in Different Agro-Climatic Zones.

    Directory of Open Access Journals (Sweden)

    Mallana Gowdra Mallikarjuna

    Full Text Available Deficiency of iron and zinc causes micronutrient malnutrition or hidden hunger, which severely affects ~25% of global population. Genetic biofortification of maize has emerged as cost effective and sustainable approach in addressing malnourishment of iron and zinc deficiency. Therefore, understanding the genetic variation and stability of kernel micronutrients and grain yield of the maize inbreds is a prerequisite in breeding micronutrient-rich high yielding hybrids to alleviate micronutrient malnutrition. We report here, the genetic variability and stability of the kernel micronutrients concentration and grain yield in a set of 50 maize inbred panel selected from the national and the international centres that were raised at six different maize growing regions of India. Phenotyping of kernels using inductively coupled plasma mass spectrometry (ICP-MS revealed considerable variability for kernel minerals concentration (iron: 18.88 to 47.65 mg kg(-1; zinc: 5.41 to 30.85 mg kg(-1; manganese: 3.30 to 17.73 mg kg(-1; copper: 0.53 to 5.48 mg kg(-1 and grain yield (826.6 to 5413 kg ha(-1. Significant positive correlation was observed between kernel iron and zinc within (r = 0.37 to r = 0.52, p < 0.05 and across locations (r = 0.44, p < 0.01. Variance components of the additive main effects and multiplicative interactions (AMMI model showed significant genotype and genotype × environment interaction for kernel minerals concentration and grain yield. Most of the variation was contributed by genotype main effect for kernel iron (39.6%, manganese (41.34% and copper (41.12%, and environment main effects for both kernel zinc (40.5% and grain yield (37.0%. Genotype main effect plus genotype-by-environment interaction (GGE biplot identified several mega environments for kernel minerals and grain yield. Comparison of stability parameters revealed AMMI stability value (ASV as the better representative of the AMMI stability parameters. Dynamic stability

  9. Soviet test yields

    Science.gov (United States)

    Vergino, Eileen S.

    Soviet seismologists have published descriptions of 96 nuclear explosions conducted from 1961 through 1972 at the Semipalatinsk test site, in Kazakhstan, central Asia [Bocharov et al., 1989]. With the exception of releasing news about some of their peaceful nuclear explosions (PNEs) the Soviets have never before published such a body of information.To estimate the seismic yield of a nuclear explosion it is necessary to obtain a calibrated magnitude-yield relationship based on events with known yields and with a consistent set of seismic magnitudes. U.S. estimation of Soviet test yields has been done through application of relationships to the Soviet sites based on the U.S. experience at the Nevada Test Site (NTS), making some correction for differences due to attenuation and near-source coupling of seismic waves.

  10. Microstructure and fatigue properties of Mg-to-steel dissimilar resistance spot welds

    International Nuclear Information System (INIS)

    Liu, L.; Xiao, L.; Chen, D.L.; Feng, J.C.; Kim, S.; Zhou, Y.

    2013-01-01

    Highlights: ► Mg/steel dissimilar spot weld had the same fatigue strength as Mg/Mg similar weld. ► Crack propagation path of Mg/Mg and Mg/steel welds was the same. ► Penetration of Zn into the Mg base metal led to crack initiation of Mg/steel weld. ► HAZ weakening and stress concentration led to crack initiation of Mg/Mg weld. -- Abstract: The structural application of lightweight magnesium alloys in the automotive industry inevitably involves dissimilar welding with steels and the related durability issues. This study was aimed at evaluating the microstructural change and fatigue resistance of Mg/steel resistance spot welds, in comparison with Mg/Mg welds. The microstructure of Mg/Mg spot welds can be divided into: base metal, heat affected zone and fusion zone (nugget). However, the microstructure of Mg/steel dissimilar spot welds had three different regions along the joined interface: weld brazing, solid-state joining and soldering. The horizontal and vertical Mg hardness profiles of Mg/steel and Mg/Mg welds were similar. Both Mg/steel and Mg/Mg welds were observed to have an equivalent fatigue resistance due to similar crack propagation characteristics and failure mode. Both Mg/steel and Mg/Mg welds failed through thickness in the magnesium sheet under stress-controlled cyclic loading, but fatigue crack initiation of the two types of welds was different. The crack initiation of Mg/Mg welds was occurred due to a combined effect of stress concentration, grain growth in the heat affected zone (HAZ), and the presence of Al-rich phases at HAZ grain boundaries, while the penetration of small amounts of Zn coating into the Mg base metal stemming from the liquid metal induced embrittlement led to crack initiation in the Mg/steel welds.

  11. Effects of Land-Applied Ammonia Scrubber Solutions on Yield, Nitrogen Uptake, Soil Test Phosphorus, and Phosphorus Runoff.

    Science.gov (United States)

    Martin, Jerry W; Moore, Philip A; Li, Hong; Ashworth, Amanda J; Miles, Dana M

    2018-03-01

    Ammonia (NH) scrubbers reduce amounts of NH and dust released from animal rearing facilities while generating nitrogen (N)-rich solutions, which may be used as fertilizers. The objective of this study was to determine the effects of various NH scrubber solutions on forage yields, N uptake, soil-test phosphorus (P), and P runoff. A small plot study was conducted using six treatments: (i) an unfertilized control, (ii) potassium bisulfate (KHSO) scrubber solution, (iii) aluminum sulfate [Al(SO) ⋅14HO, alum] scrubber solution, (iv) sodium bisulfate (NaHSO) scrubber solution, (v) sulfuric acid (HSO) scrubber solution, and (vi) ammonium nitrate (NHNO) fertilizer. The scrubber solutions were obtained from ARS Air Scrubbers attached to commercial broiler houses. All N sources were applied at a rate of 112 kg N ha. Plots were harvested approximately every 4 wk and soil-test P measurements were made, then a rainfall simulation study was conducted. Cumulative forage yields were greater ( scrubber solutions than for alum (6.7 Mg ha) or HSO (6.5 Mg ha) scrubber solutions or for NHNO (6.9 Mg ha). All N sources resulted in higher yields than the control (5.1 Mg ha). The additional potassium in the KHSO treatment likely resulted in higher yields. Although Mehlich-III-extractable P was not affected, water-extractable P in soil was lowered by the alum-based scrubber solution, which also resulted in lower P runoff. This study demonstrates that N captured using NH scrubbers is a viable N fertilizer. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  12. Effect of Mg content on microstructure and corrosion behavior of hot dipped Zn–Al–Mg coatings

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Caizhen; Lv, Haibing [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Zhu, Tianping [Department of Chemical and Materials Engineering, The University of Auckland, PB 92019, Auckland 1142 (New Zealand); Zheng, Wanguo [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Yuan, Xiaodong, E-mail: xdyuan@caep.cn [Research Centre of Laser Fusion, CAEP, P.O.Box 919-988-5, Mianyang, Sichuan 621900 (China); Gao, Wei, E-mail: w.gao@auckland.ac.nz [Department of Chemical and Materials Engineering, The University of Auckland, PB 92019, Auckland 1142 (New Zealand)

    2016-06-15

    In this article, Zn–Al–Mg coatings were prepared by hot dipping method. The surface morphology, cross–section microstructure, microhardness, composition, corrosion behaviour of ZAM coatings were investigated by using X–ray diffraction (XRD), Optical microscope, Environmental scanning electron microscopy equipped with EDS (FESEM–EDS), Microhardness tester and Electrochemical analysis respectively. Corrosion test was also performed in a standard salt fog spray chamber. Microstructure studies indicates that Zn grain size was refined and eutectic areas at Zn grain boundary areas increased with increasing Mg content. ZA5M1.5 and ZA5M2 coatings have two distinct layers. Mg tends to exist in the outer layer while Al is in the inner layer. The inner layer is composed of Al{sub 5}Fe{sub 2}Zn{sub 0.4} intermetallic, which may to contribute to the microhardness. The outer layer is Zn grains surrounded by Zn–Mg etutectics, which may improve the corrosion resistance. The microhardness is more than 700 HV{sub 50g} for Al-rich layer and around 151 HV{sub 25g} for Mg-rich layer. The improved corrosion resistance of Zn–5%Al-1.5%Mg coating comes from the corrosion product of flocculent type simonkolleite, which prolongs the micro-path and impedes the movement of O{sub 2} and H{sub 2}O, ultimately retards the overall corrosion process. - Highlights: • Two-layer structured Zn–Al–Mg coatings were prepared by hot dipping method. • Mg exists in the outer layer while Al exists in the inner layer of Zn–Al–Mg coating. • Zn–Al–Mg coating has better protective ability than Zn and Zn–Al coatings. • The Mg-modified simonkolleite is the reason of the enhanced corrosion resistance.

  13. Phase formation in Mg-Sn-Si and Mg-Sn-Si-Ca alloys

    Energy Technology Data Exchange (ETDEWEB)

    Kozlov, A.; Groebner, J. [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Schmid-Fetzer, R., E-mail: schmid-fetzer@tu-clausthal.de [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany)

    2011-02-17

    Research highlights: > The solidification paths of ternary and quaternary alloys are analyzed in detail, using the tool of thermodynamic calculations. > The precipitation sequence of phases and their amounts compare well with the microstructure of alloys. > The most efficient comparison to the experimental thermal analysis data is done by calculation of the enthalpy variation with temperature. > The viability of a procedure for the selection of multicomponent key samples is demonstrated for the development of the Mg-Ca-Si-Sn phase diagram. - Abstract: Experimental work is done and combined with the Calphad method to generate a consistent thermodynamic description of the Mg-Ca-Si-Sn quaternary system, validated for Mg-rich alloys. The viability of a procedure for the selection of multicomponent key samples is demonstrated for this multicomponent system. Dedicated thermal analysis with DTA/DSC on sealed samples is performed and the microstructure of slowly solidified alloys is analyzed using SEM/EDX. The thermodynamic description and phase diagram of the ternary Mg-Si-Sn system, developed in detail also in this work, deviates significantly from a previous literature proposal. The phase formation in ternary and quaternary alloys is analyzed using the tool of thermodynamic equilibrium and Scheil calculations for the solidification paths and compared with present experimental data. The significant ternary/quaternary solid solubilities of pertinent intermetallic phases are quantitatively introduced in the quaternary Mg-Ca-Si-Sn phase diagram and validated by experimental data.

  14. Enhancement of HHG yield

    International Nuclear Information System (INIS)

    Serrat, C.; Biegert, J.

    2011-01-01

    A static electric field periodically distributed in space controls and enhances the yield in high harmonic generation. The method is relatively simple to implement and allows tuning from the extreme-ultraviolet to soft X-ray. The radiation yield is selectively enhanced due to symmetry breaking induced by a static electric field on the interaction between the driving laser and the medium. The enhanced spectral region is tuned by varying the periodicity of the static electric field. Simulations predict an increase of more than two orders of magnitude for harmonics in the water window spectral range.

  15. nduced hyperlipidemic rats. Methods: Column chromatographic fractionation of butanol fraction of total methanol extract of leaves of Bauhinia variegata (Linn. yields four sub-fractions (sub-fraction A-D. All sub-fractions tested for their anti-hyperlipidemic activity. Sub-fractions administered at a dose of 65 mg/kg (oral to the Triton WR-1339 induced hyperlipidemic rats and total cholesterol, triglycerides, HDL, LDL and VLDL

    Directory of Open Access Journals (Sweden)

    Deepak Kumar

    2012-10-01

    Full Text Available Objective: To investigate the effect and evaluation of Anti-hyperlipidemic activity guided subfraction isolated from total methanolic extract of Bauhinia variegata (Linn. leaves on Triton WR-1339 induced hyperlipidemic rats. Methods: Column chromatographic fractionation of butanol fraction of total methanol extract of leaves of Bauhinia variegata (Linn. yields four subfractions (sub-fraction A-D. All sub-fractions tested for their anti-hyperlipidemic activity. Subfractions administered at a dose of 65 mg/kg (oral to the Triton WR-1339 induced hyperlipidemic rats and total cholesterol, triglycerides, HDL, LDL and VLDL level in the blood were checked. Results: Sub-fraction D showed significant reduction (P<0.05 among four sub-fraction in comparison with standard drug fenofibrate. Conclusions: From the above study it could be concluded that butanol sub-fraction D of Bauhinia variegata (Linn. not only have resulted in significant reduction in cholesterol, triglyceride, LDL, VLDL level but also increases the HDL level at a reduced dose level.

  16. Quasicrystal-reinforced Mg alloys.

    Science.gov (United States)

    Kyun Kim, Young; Tae Kim, Won; Hyang Kim, Do

    2014-04-01

    The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg-Zn-Y and Mg-Zn-Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α -Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by the strong bonding property at the I-phase/matrix interface. The presence of an additional secondary solidification phase can further enhance formability and mechanical properties. In Mg-Zn-Y alloys, the co-presence of I and Ca 2 Mg 6 Zn 3 phases by addition of Ca can significantly enhance formability, while in Mg-Zn-Al alloys, the co-presence of the I-phase and Mg 2 Sn phase leads to the enhancement of mechanical properties. Dynamic and static recrystallization are significantly accelerated by addition of Ca in Mg-Zn-Y alloy, resulting in much smaller grain size and more random texture. The high strength of Mg-Zn-Al-Sn alloys is attributed to the presence of finely distributed Mg 2 Sn and I-phase particles embedded in the α -Mg matrix.

  17. Cigarette nicotine yields and nicotine intake among Japanese male workers

    OpenAIRE

    Ueda, K; Kawachi, I; Nakamura, M; Nogami, H; Shirokawa, N; Masui, S; Okayama, A; Oshima, A

    2002-01-01

    Objectives: To analyse brand nicotine yield including "ultra low" brands (that is, cigarettes yielding ≤ 0.1 mg of nicotine by Federal Trade Commission (FTC) methods) in relation to nicotine intake (urinary nicotine, cotinine and trans-3'-hydroxycotinine) among 246 Japanese male smokers.

  18. Improving growth and yield of cowpea by foliar application of ...

    African Journals Online (AJOL)

    Water stress impaired cowpea plant growth and decreased ion percentage and chlorophyll and carbohydrate concentration in the shoot as well as yield and its quality. Foliar-applied chitosan, in particular 250 mg/l, increased plant growth, yield and its quality as well as physiological constituents in plant shoot under stressed ...

  19. Energetics of Mg incorporation at GaN(0001) and GaN(0001¯) surfaces

    Science.gov (United States)

    Sun, Qiang; Selloni, Annabella; Myers, T. H.; Doolittle, W. Alan

    2006-04-01

    By using density functional calculations in the generalized gradient approximation, we investigate the energetics of Mg adsorption and incorporation at GaN(0001) and GaN(0001¯) surfaces under various Ga and Mg coverage conditions as well as in presence of light or electron beam-induced electronic excitation. We find significant differences in Mg incorporation between Ga- and N-polar surfaces. Mg incorporation is easier at the Ga-polar surface, but high Mg coverages are found to cause important distortions which locally change the polarity from Ga to N polar. At the N-rich and moderately Ga-rich GaN(0001) surface, 0.25 ML of Mg substituting Ga in the top bilayer strongly reduce the surface diffusion barriers of Ga and N adatoms, in agreement with the surfactant effect observed in experiments. As the Mg coverage exceeds 0.5 ML, partial incorporation in the subsurface region (second bilayer) becomes favorable. A surface structure with 0.5 ML of incorporated Mg in the top bilayer and 0.25 ML in the second bilayer is found to be stable over a wide range of Ga chemical potential. At the Ga bilayer-terminated GaN(0001) surface, corresponding to Ga-rich conditions, configurations where Mg is incorporated in the interface region between the metallic Ga bilayer and the underlying GaN bilayer appear to be favored. At the N-polar surface, Mg is not incorporated under N-rich or moderately Ga-rich conditions, whereas incorporation in the adlayer may take place under Ga-rich conditions. In the presence of light or electron beam induced excitation, energy differences between Mg incorporated at the surface and in deeper layers are reduced so that the tendency toward surface segregation is also reduced.

  20. Physiological indexese macro- and micronutrients in plant tissue and essential oil of Mentha piperita L. grown in nutrient solution with variation in N, P, K and Mg levels

    Directory of Open Access Journals (Sweden)

    E.F.S. David

    2014-03-01

    Full Text Available Mentha piperita L. is an aromatic and medicinal species of the family Lamiaceae, known as mint or peppermint, and its leaves and branches produce essential oil rich in menthol. This study aimed to evaluate physiological indexes, macro- and micronutrients inthe shootsand essential oil of Mentha piperita L. grown in nutrient solution number 2 of Hoagland and Arnon (1950 with different N, P, K and Mg levels. Shoot length, dry mass of the different organs, total dry mass, leaf area, essential oil yield and composition, and macronutrient (N, P, K, Mg, Ca, S and micronutrient (Mn, Cu, Fe, Zn contents in the shoot were evaluated. Plants treated with 65%N/50%P/25%K/100%Mg had a tendency towards longer shoot, greaterroot and leaf blade dry masses, higher essential oil yield, higher menthol levels and lower menthone levels. The results showed that Mentha can be grown in nutrient solution by reducing 65% N, 50% P, 25% K and 100% Mg. This solution had better development compared to the other tested treatments. Therefore,we recommendMentha piperita L. to be grown with such nutrient levels.

  1. Investigating the hydrological significance of stalagmite geochemistry (Mg, Sr) using Sr isotope and particulate element records across the Late Glacial-to-Holocene transition

    Science.gov (United States)

    Belli, R.; Borsato, A.; Frisia, S.; Drysdale, R.; Maas, R.; Greig, A.

    2017-02-01

    The trace element and Sr isotope records in two coeval stalagmites characterized by different growth rates and flow regimes at Savi cave (Grotta Savi, NE Italy) reveal different sources and incorporation mechanisms for Mg and Sr. Mg is sourced primarily from dissolved cave host rock while particulate Mg derived from soil plays a subordinate role. The presence of particulate-borne Mg is inferred from the co-variation of Mg and particle-associated elements (Th, Al and Mn) which are preferentially concentrated in open columnar calcite layers. Variation in Mg concentrations corrected for particle-influenced components, the Mgc parameter, is controlled by water-rock interaction, with higher and lower Mgc during dry and wet phases, respectively. This is thought to reflect incongruent dissolution of Mg-rich phases. Correction of Sr concentrations for contributions from airborne exogenic Sr, based on 87Sr/86Sr ratios, yields the bedrock-only contribution (Src). Src variation in stalagmite calcite is influenced by speleothem growth rate and by variation of the calcite-water Sr partitioning in wet and dry phases, and only to a minor extent by incongruent dissolution of Mg-rich phases. Concentration profiles for Mgc and Srcg (corrected for growth rate effects) show inverse correlations and are inferred to show hydrological significance which is captured in a hydrological index, HI. We suggest HI provides robust information on water-rock interaction related to hydrological changes and can be utilized in both wet and semi-arid environments, provided the corrections for soil Mg and exogenic Sr can be applied with confidence. Application of the HI index allows correction of Grotta Savi oxygen isotope data, to yield a δ18Oc time series that shows when changes in moisture sources and atmospheric reorganization, or changes in moisture amount, were significant. This is especially evident during the Younger Dryas (YD). The Savi record supports the concept of a two-phase YD, marked by

  2. Magnesium-rich Basalts on Mercury

    Science.gov (United States)

    Martel, L. M. V.

    2013-05-01

    X-ray and gamma-ray spectrometers on NASA's MESSENGER spacecraft are making key measurements regarding the composition and properties of the surface of Mercury, allowing researchers to more clearly decipher the planet's formation and geologic history. The origin of the igneous rocks in the crust of Mercury is the focus of recent research by Karen Stockstill-Cahill and Tim McCoy (National Museum of Natural History, Smithsonian Institution), along with Larry Nittler and Shoshana Weider (Carnegie Institution of Washington) and Steven Hauck II (Case Western Reserve University). Using the well-known MELTS computer code Stockstill-Cahill and coauthors worked with MESSENGER-derived and rock-analog compositions to constrain petrologic models of the lavas that erupted on the surface of Mercury. Rock analogs included a partial melt of the Indarch meteorite and a range of Mg-rich terrestrial rocks. Their work shows the lavas on Mercury are most similar to terrestrial magnesian basalt (with lowered FeO content). The implications of the modeling are that Mg-rich lavas came from high-temperature sources in Mercury's mantle and erupted at high temperature with exceptionally low viscosity into thinly bedded and laterally extensive flows, concepts open to further evaluation by laboratory experiments and by geologic mapping of Mercury's surface using MESSENGER's imaging system and laser altimeter to document flow features and dimensions.

  3. Effect of Cr, Ti, V, and Zr Micro-additions on Microstructure and Mechanical Properties of the Al-Si-Cu-Mg Cast Alloy

    Science.gov (United States)

    Shaha, S. K.; Czerwinski, F.; Kasprzak, W.; Friedman, J.; Chen, D. L.

    2016-05-01

    Uniaxial static and cyclic tests were used to assess the role of Cr, Ti, V, and Zr additions on properties of the Al-7Si-1Cu-0.5Mg (wt pct) alloy in as-cast and T6 heat-treated conditions. The microstructure of the as-cast alloy consisted of α-Al, eutectic Si, and Cu-, Mg-, and Fe-rich phases Al2.1Cu, Al8.5Si2.4Cu, Al5.2CuMg4Si5.1, and Al14Si7.1FeMg3.3. In addition, the micro-sized Cr/Zr/Ti/V-rich phases Al10.7SiTi3.6, Al6.7Si1.2TiZr1.8, Al21.4Si3.4Ti4.7VZr1.8, Al18.5Si7.3Cr2.6V, Al7.9Si8.5Cr6.8V4.1Ti, Al6.3Si23.2FeCr9.2V1.6Ti1.3, Al92.2Si16.7Fe7.6Cr8.3V1.8, and Al8.2Si30.1Fe1.6Cr18.8V3.3Ti2.9Zr were present. During solution treatment, Cu-rich phases were completely dissolved, while the eutectic silicon, Fe-, and Cr/Zr/Ti/V-rich intermetallics experienced only partial dissolution. Micro-additions of Cr, Zr, Ti, and V positively affected the alloy strength. The modified alloy in the T6 temper during uniaxial tensile tests exhibited yield strength of 289 MPa and ultimate tensile strength of 342 MPa, being significantly higher than that for the Al-Si-Cu-Mg base. Besides, the cyclic yield stress of the modified alloy in the T6 state increased by 23 pct over that of the base alloy. The fatigue life of the modified alloy was substantially longer than that of the base alloy tested using the same parameters. The role of Cr, Ti, V, and Zr containing phases in controlling the alloy fracture during static and cyclic loading is discussed.

  4. LHCB RICH gas system proposal

    CERN Document Server

    Bosteels, Michel; Haider, S

    2001-01-01

    Both LHCb RICH will be operated with fluorocarbon as gas radiator. RICH 1 will be filled with 4m^3 of C4F10 and RICH 2 with 100m^3 of CF4. The gas systems will run as a closed loop circulation and a gas recovery system within the closed loop is planned for RICH 1, where the recovery of the CF4 will only be realised during filling and emptying of the detector. Inline gas purification is foreseen for the gas systems in order to limit water and oxygen impurities.

  5. Metallurgical Parameters Controlling the Eutectic Silicon Charateristics in Be-Treated Al-Si-Mg Alloys.

    Science.gov (United States)

    Ibrahim, Mohamed F; Elgallad, Emad M; Valtierra, Salvador; Doty, Herbert W; Samuel, Fawzy H

    2016-01-27

    The present work was carried out on Al-7%Si-0.4%Mg-X alloy (where X = Mg, Fe, Sr or Be), where the effect of solidification rate on the eutectic silicon characteristics was investigated. Two solidification rates corresponding to dendrite arm spacings (DAS) of 24 and 65 μm were employed. Samples with 24 μm DAS were solution heat-treated at 540 °C for 5 and 12 h prior to quenching in warm water at 65 °C. Eutectic Si particle charateristics were measured using an image analyzer. The results show that the addition of 0.05% Be leads to partial modification of the Si particles. Full modification was only obtained when Sr was added in an amount of 150-200 ppm, depending on the applied solidification rate. Increasing the amount of Mg to 0.8% in Sr-modified alloys leads to a reduction in the effectiveness of Sr as the main modifier. Similar observations were made when the Fe content was increased in Be-treated alloys due to the Be-Fe interaction. Over-modification results in the precipitation of hard Sr-rich particles, mainly Al₄SrSi₂, whereas overheating causes incipient melting of the Al-Cu eutectic and hence the surrounding matrix. Both factors lead to a deterioration in the alloy mechanical properties. Furthermore, the presence of long, acicular Si particles accelerates the occurrence of fracture and, as a result, yields poor ductility. In low iron (less than 0.1 wt%) Al-Si-Mg alloys, the mechanical properties in the as cast, as well as heat treated conditions, are mainly controlled by the eutectic Si charatersitics. Increasing the iron content and, hence, the volume fraction of Fe-based intermetallics leads to a complex fracture mode.

  6. Metallurgical Parameters Controlling the Eutectic Silicon Charateristics in Be-Treated Al-Si-Mg Alloys

    Directory of Open Access Journals (Sweden)

    Mohamed F. Ibrahim

    2016-01-01

    Full Text Available The present work was carried out on Al-7%Si-0.4%Mg-X alloy (where X = Mg, Fe, Sr or Be, where the effect of solidification rate on the eutectic silicon characteristics was investigated. Two solidification rates corresponding to dendrite arm spacings (DAS of 24 and 65 μm were employed. Samples with 24 μm DAS were solution heat-treated at 540 °C for 5 and 12 h prior to quenching in warm water at 65 °C. Eutectic Si particle charateristics were measured using an image analyzer. The results show that the addition of 0.05% Be leads to partial modification of the Si particles. Full modification was only obtained when Sr was added in an amount of 150–200 ppm, depending on the applied solidification rate. Increasing the amount of Mg to 0.8% in Sr-modified alloys leads to a reduction in the effectiveness of Sr as the main modifier. Similar observations were made when the Fe content was increased in Be-treated alloys due to the Be-Fe interaction. Over-modification results in the precipitation of hard Sr-rich particles, mainly Al4SrSi2, whereas overheating causes incipient melting of the Al-Cu eutectic and hence the surrounding matrix. Both factors lead to a deterioration in the alloy mechanical properties. Furthermore, the presence of long, acicular Si particles accelerates the occurrence of fracture and, as a result, yields poor ductility. In low iron (less than 0.1 wt% Al-Si-Mg alloys, the mechanical properties in the as cast, as well as heat treated conditions, are mainly controlled by the eutectic Si charatersitics. Increasing the iron content and, hence, the volume fraction of Fe-based intermetallics leads to a complex fracture mode.

  7. Brazilian Soybean Yields and Yield Gaps Vary with Farm Size

    Science.gov (United States)

    Jeffries, G. R.; Cohn, A.; Griffin, T. S.; Bragança, A.

    2017-12-01

    Understanding the farm size-specific characteristics of crop yields and yield gaps may help to improve yields by enabling better targeting of technical assistance and agricultural development programs. Linking remote sensing-based yield estimates with property boundaries provides a novel view of the relationship between farm size and yield structure (yield magnitude, gaps, and stability over time). A growing literature documents variations in yield gaps, but largely ignores the role of farm size as a factor shaping yield structure. Research on the inverse farm size-productivity relationship (IR) theory - that small farms are more productive than large ones all else equal - has documented that yield magnitude may vary by farm size, but has not considered other yield structure characteristics. We examined farm size - yield structure relationships for soybeans in Brazil for years 2001-2015. Using out-of-sample soybean yield predictions from a statistical model, we documented 1) gaps between the 95th percentile of attained yields and mean yields within counties and individual fields, and 2) yield stability defined as the standard deviation of time-detrended yields at given locations. We found a direct relationship between soy yields and farm size at the national level, while the strength and the sign of the relationship varied by region. Soybean yield gaps were found to be inversely related to farm size metrics, even when yields were only compared to farms of similar size. The relationship between farm size and yield stability was nonlinear, with mid-sized farms having the most stable yields. The work suggests that farm size is an important factor in understanding yield structure and that opportunities for improving soy yields in Brazil are greatest among smaller farms.

  8. Estimating Corporate Yield Curves

    OpenAIRE

    Antionio Diaz; Frank Skinner

    2001-01-01

    This paper represents the first study of retail deposit spreads of UK financial institutions using stochastic interest rate modelling and the market comparable approach. By replicating quoted fixed deposit rates using the Black Derman and Toy (1990) stochastic interest rate model, we find that the spread between fixed and variable rates of interest can be modeled (and priced) using an interest rate swap analogy. We also find that we can estimate an individual bank deposit yield curve as a spr...

  9. Information rich display design

    International Nuclear Information System (INIS)

    Welch, Robin; Braseth, Alf Ove; Veland, Oeystein

    2004-01-01

    This paper presents the concept Information Rich Displays. The purpose of Information Rich Displays (IRDs) is to condensate prevailing information in process displays in such a way that each display format (picture) contains more relevant information for the user. Compared to traditional process control displays, this new concept allows the operator to attain key information at a glance and at the same time allows for improved monitoring of larger portions of the process. This again allows for reduced navigation between both process and trend displays and ease the cognitive demand on the operator. This concept has been created while working on designing display prototypes for the offshore petroleum production facilities of tomorrow. Offshore installations basically consist of wells, separation trains (where oil, gas and water are separated from each other), an oil tax measurement system (where oil quality is measured and the pressure increased to allow for export), gas compression (compression of gas for export) and utility systems (water treatment, chemical systems etc.). This means that an offshore control room operator has to deal with a complex process that comprises several functionally different systems. The need for a new approach to offshore display format design is in particular based on shortcomings in today's designs related to the keyhole effect, where the display format only reveals a fraction of the whole process. Furthermore, the upcoming introduction of larger off- and on-shore operation centres will increase the size and complexity of the operators' work domain. In the light of the increased demands on the operator, the proposed IRDs aim to counter the negative effects this may have on the workload. In this work we have attempted to classify the wide range of different roles an operator can have in different situations. The information content and amount being presented to the operator in a display should be viewed in context of the roles the

  10. Biochemical Studies in Some Indigenous Dye Yielding Plants of Manipur

    Directory of Open Access Journals (Sweden)

    Joylani D. SAIKHOM

    2013-08-01

    Full Text Available Ten natural dye yielding and two mordant plants were biochemically analyzed. Though natural dyes are widely used, information about the active principles responsible for dyeing is hardly available. In the present experiment, total chlorophyll, carotinoids, tannins, phenolics, flavonoids and curcumin were determined among the dye yielding plants, while K, S, P, Ca, Mg, Mn, Zn, Fe, Cu and Co were determined in the case of mordant plants. In Bixa orellana, used for yellow dyeing, the carotinoid content was 163.11 mg g-1 and in Clerodendrum chinense and Datura stramonium, which were used for green colouring, total chlorophyll content of 10.29 mg and 11.83 mg g-1 was recorded. Curcumin content responsible for orange colouring in Curcuma domestica was 27.7 mg g-1 while flavonoid content in Solanum nigrum and Terminalia chebula, which were used for brown, brown to black dyes was 24.89 and 21.73 mg g-1. Among the plants used for dyeing different colours, Punica granatum and Parkia timoriana were found to contain higher amounts of total phenols and bound phenols by recording 681.2 mg g-1 and 287.6 mg g-1 total phenols and 151.6 mg g-1 and 130.2mg g-1 bound phenols, while higher amounts of orthodihydric phenols and tannins were recorded in Punica granatum and Strobilanthes flaccidifolius by recording 20.11mg g-1 and 9.54mg g-1 orthodihydric phenols and 675.57mg g-1 and 648.12 mg g-1 tannins, respectively. In case of the plants used as mordant, higher contents of Ca, Mg, K, Zn, Fe and Mn were detected in Achyranthes aspera, while higher amounts of P, Fe and Cu were recorded in Garcinia xanthochymus.

  11. Uncovering the Local Magnesium Environment in the Metal–Organic Framework Mg 2 (dobpdc) Using 25 Mg NMR Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Jun; Blaakmeer, E. S. Merijn [Institute; Lipton, Andrew S. [Environmental; McDonald, Thomas M.; Liu, Yifei Michelle; Smit, Berend [Laboratory; Long, Jeffrey R. [Materials; Kentgens, Arno P. M. [Institute; Reimer, Jeffrey A. [Materials

    2017-09-06

    The incorporation of N,N'-dimethylethylenediamine into an expanded MOF-74 framework has yielded a material (mmen-Mg2(dobpdc)) exhibiting “step-shaped” CO2 adsorption isotherms. The coordination of mmen at the Mg open metal center is essential for the unique cooperative adsorption mechanism elucidated for this material. Despite its importance for carbon capture, there is as yet no experimental structure determination available for the underlying metal– organic framework Mg2(dobpdc). Our 25Mg solid-state NMR data unravel the local Mg environments in several Mg2(dobpdc) samples, unambiguously confirming the formation of fivecoordinate Mg centers in the activated material and six-coordinate Mg centers in the solvent- or diamine-loaded samples, such as mmen-Mg2(dobpdc). A fraction of the Mg centers are locally disordered due to the framework deformation accompanied by the guest distributions and dynamics.

  12. Growth kinetics of cellular precipitation in a Mg-8.5Al-0.5Zn-0.2Mn (wt.%) alloy

    Energy Technology Data Exchange (ETDEWEB)

    Contreras-Piedras, Edgar [Instituto Politecnico Nacional-ESIQIE-DIMM-ESFM, Apartado Postal 118-430, Admon. GAM, Mexico, D.F. 07051 (Mexico); Esquivel-Gonzalez, Ramon [Universidad del Valle de Mexico, Depto. Ingenierias, Paseo de las Aves 1, Col. San Mateo Nopala, Lomas Verdes, Naucalpan de Juarez, Edo. Mex. 53220 (Mexico); Lopez-Hirata, Victor M.; Saucedo-Munoz, M.L.; Paniagua-Mercado, Ana M. [Instituto Politecnico Nacional-ESIQIE-DIMM-ESFM, Apartado Postal 118-430, Admon. GAM, Mexico, D.F. 07051 (Mexico); Dorantes-Rosales, Hector J., E-mail: hectordorantes@yahoo.com [Instituto Politecnico Nacional-ESIQIE-DIMM-ESFM, Apartado Postal 118-430, Admon. GAM, Mexico, D.F. 07051 (Mexico)

    2010-11-15

    Research highlights: {yields} The growth kinetics of lamellar spacing follows the behavior predicted by Turnbull theory. {yields} The growth kinetics of cellular precipitation is a process controlled by grain boundary diffusion. {yields} The presence of two types of morphology for cellular precipitation depends on the aging temperature. {yields} The highest hardness peak is associated to a fine continuous precipitation at the lowest temperature. {yields} The lowest hardness is attributed to the fast coarsening process of both precipitations. - Abstract: Microstructural evolution and growth kinetics were studied in an isothermally aged Mg-8.5Al-0.5Zn-0.2Mn (wt.%) alloy by means of X-ray diffraction, scanning electron microscopy, Vickers hardness measurements and transmission electron microscopy. Specimens were solution-treated and then aged at 373, 473 and 573 K for different time period. The characterization results indicated the presence of both continuous and discontinuous precipitations of the Mg{sub 17}Al{sub 12}-{gamma} phase in a Mg-rich matrix. The discontinuous or cellular precipitation was present with a lamellar structure, and the growth kinetics was evaluated using the Johnson-Mehl-Avrami-Kolmogorov equation analysis, which gives a time exponent close to 1. This value confirms that cellular precipitation takes place on the saturation sites corresponding to grain boundaries. In addition, the activation energy for cellular precipitation was determined to be about 64.6 kJ mol{sup -1}. This also indicates a grain boundary diffusion process. The variation of cellular spacing with temperature follows the behavior expected by Turnbull theory. The highest hardness peak corresponded to the lowest aging temperature and it is associated with a fine continuous precipitation; while the lowest hardness peak was detected at the highest aging temperature and it is attributed to the rapid coarsening process of both precipitations.

  13. Small millet farmers increase yields through participatory varietal ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Small millets, despite being rich in micronutrients and dietary fibre and known for their low glycemic index and tolerance of water stress, are in decline in South Asia. Existing varieties suffer from low yield and farmers lack access to improved varieties. The Revalorising Small Millets in Rainfed Regions of South Asia ...

  14. Effect of amorphous Mg{sub 50}Ni{sub 50} on hydriding and dehydriding behavior of Mg{sub 2}Ni alloy

    Energy Technology Data Exchange (ETDEWEB)

    Guzman, D., E-mail: danny.guzman@uda.cl [Departamento de Ingenieria en Metalurgia, Facultad de Ingenieria, Universidad de Atacama y Centro Regional de Investigacion y Desarrollo Sustentable de Atacama (CRIDESAT), Av. Copayapu 485, Copiapo (Chile); Ordonez, S. [Departamento de Ingenieria Metalurgica, Facultad de Ingenieria, Universidad de Santiago de Chile, Av. Lib. Bernardo O' Higgins 3363, Santiago (Chile); Fernandez, J.F.; Sanchez, C. [Departamento de Fisica de Materiales, Facultad de Ciencias, Universidad Autonoma de Madrid, Cantoblanco 28049, Madrid (Spain); Serafini, D. [Departamento de Fisica, Facultad de Ciencias, Universidad de Santiago de Chile and Center for Interdisciplinary Research in Materials, CIMAT, Av. Lib. Bernardo O' Higgins 3363, Santiago (Chile); Rojas, P.A. [Escuela de Ingenieria Mecanica, Facultad de Ingenieria, Av. Los Carrera 01567, Quilpue, Pontificia Universidad Catolica de Valparaiso, PUCV (Chile); Aguilar, C. [Departamento de Ingenieria Metalurgica y Materiales, Universidad Tecnica Federico Santa Maria, Av. Espana 1680, Valparaiso (Chile); Tapia, P. [Departamento de Ingenieria en Metalurgia, Facultad de Ingenieria, Universidad de Atacama, Av. Copayapu 485, Copiapo (Chile)

    2011-04-15

    Composite Mg{sub 2}Ni (25 wt.%) amorphous Mg{sub 50}Ni{sub 50} was prepared by mechanical milling starting with nanocrystalline Mg{sub 2}Ni and amorphous Mg{sub 50}Ni{sub 50} powders, by using a SPEX 8000 D mill. The morphological and microstructural characterization of the powders was performed via scanning electron microscopy and X-ray diffraction. The hydriding characterization of the composite was performed via a solid gas reaction method in a Sievert's-type apparatus at 363 K under an initial hydrogen pressure of 2 MPa. The dehydriding behavior was studied by differential thermogravimetry. On the basis of the results, it is possible to conclude that amorphous Mg{sub 50}Ni{sub 50} improved the hydriding and dehydriding kinetics of Mg{sub 2}Ni alloy upon cycling. A tentative rationalization of experimental observations is proposed. - Research Highlights: {yields} First study of the hydriding behavior of composite Mg{sub 2}Ni (25 wt.%) amorphous Mg{sub 50}Ni{sub 50}. {yields} Microstructural characterization of composite material using XRD and SEM was obtained. {yields} An improved effect of Mg{sub 50}Ni{sub 50} on the Mg{sub 2}Ni hydriding behavior was verified. {yields} The apparent activation energy for the hydrogen desorption of composite was obtained.

  15. Shotgun Approach to Increasing Enzymatic Saccharification Yields of Ammonia Fiber Expansion Pretreated Cellulosic Biomass

    International Nuclear Information System (INIS)

    Chundawat, Shishir P. S.; Uppugundla, Nirmal; Gao, Dahai; Curran, Paul G.; Balan, Venkatesh; Dale, Bruce E.

    2017-01-01

    Most cellulolytic enzyme blends, either procured from a commercial vendor or isolated from a single cellulolytic microbial secretome, do not efficiently hydrolyze ammonia-pretreated (e.g., ammonia fiber expansion, AFEX) lignocellulosic agricultural crop residues like corn stover to fermentable sugars. Typically reported commercial enzyme loading (30–100 mg protein/g glucan) necessary to achieve >90% total hydrolysis yield (to monosaccharides) for AFEX-treated biomass, within a short saccharification time frame (24–48 h), is economically unviable. Unlike acid-based pretreatments, AFEX retains most of the hemicelluloses in the biomass and therefore requires a more complex suite of enzymes for efficient hydrolysis of cellulose and hemicellulose at industrially relevant high solids loadings. One strategy to reduce enzyme dosage while improving cocktail effectiveness for AFEX-treated biomass has been to use individually purified enzymes to determine optimal enzyme combinations to maximize hydrolysis yields. However, this approach is limited by the selection of heterologous enzymes available or the labor required for isolating low-abundance enzymes directly from the microbial secretomes. Here, we show that directly blending crude cellulolytic and hemicellulolytic enzymes-rich microbial secretomes can maximize specific activity on AFEX-treated biomass without having to isolate individual enzymes. Fourteen commercially available cellulolytic and hemicellulolytic enzymes were procured from leading enzyme companies (Novozymes ® , Genencor ® , and Biocatalysts ® ) and were mixed together to generate several hundred unique cocktail combinations. The mixtures were assayed for activity on AFEX-treated corn stover (AFEX-CS) using a previously established high-throughput methodology. The optimal enzyme blend combinations identified from these screening assays were enriched in various low-abundance hemicellulases and accessory enzymes typically absent in most commercial

  16. Role of Cu-Mg-Al mixed oxide catalysts in lignin depolymerization in supercritical ethanol

    NARCIS (Netherlands)

    Huang, X.; Ceylanpinar, A.; Koranyi, T.I.; Boot, M.D.; Hensen, E.J.M.

    2015-01-01

    We investigate the role of Cu-Mg-Al mixed oxides in depolymerization of soda lignin in supercritical ethanol. A series of mixed oxides with varying Cu content and (Cu+Mg)/Al ratio were prepared. The optimum catalyst containing 20 wt% Cu and having a (Cu+Mg)/Al ratio of 4 yielded 36 wt% monomers

  17. Status of fission yield measurements

    International Nuclear Information System (INIS)

    Maeck, W.J.

    1979-01-01

    Fission yield measurement and yield compilation activities in the major laboratories of the world are reviewed. In addition to a general review of the effort of each laboratory, a brief summary of yield measurement activities by fissioning nuclide is presented. A new fast reactor fission yield measurement program being conducted in the US is described

  18. Synthesis, crystal growth and structure of Mg containing β-rhombohedral boron: MgB17.4

    International Nuclear Information System (INIS)

    Adasch, Volker; Hess, Kai-Uwe; Ludwig, Thilo; Vojteer, Natascha; Hillebrecht, Harald

    2006-01-01

    For the first time, single crystals of Mg containing β-rhombohedral boron MgB 17.4 were synthesised from the elements in a Mg/Cu melt at 1600deg. C. The crystal structure determined by the refinement of single crystal data (space group R-3m, a=10.991(2)A, c=24.161(4)A, 890 reflections, 123 variables, R 1 (F)=0.049, wR 2 (I)=0.122) improves and modifies the former structure model derived from earlier investigations on powder samples. Mg is located on four different positions with partial occupation. While the occupation of the sites D (53.3%), E (91%) and F (7.2%) is already known from other boron-rich borides related to β-rhombohedral boron, the occupation of the fourth position (18h, 6.7%) is observed for the first time. Two boron positions show partial occupation. The summation reveals the composition MgB 17.4 and Mg 5.85 B 101.9 , respectively, confirmed by WDX measurements. The single crystals of MgB 17.4 show the highest Mg content ever found. Preliminary measurements indicate no superconductivity

  19. Enhanced yield of phenolic extracts from banana peels (Musa acuminata Colla AAA) and cinnamon barks (Cinnamomum varum) and their antioxidative potentials in fish oil.

    Science.gov (United States)

    Anal, Anil Kumar; Jaisanti, Sirorat; Noomhorm, Athapol

    2014-10-01

    The bioactive compounds of banana peels and cinnamon barks were extracted by vacuum microwave and ultrasonic-assisted extraction methods at pre-determined temperatures and times. These methods enhance the yield extracts in shorter time. The highest yields of both extracts were obtained from the conditions which employed the highest temperature and the longest time. The extracts' yield from cinnamon bark method was higher by ultrasonic than vacuum microwave method, while vacuum microwave method gave higher extraction yield from banana peel than ultrasonic method. The phenolic contents of cinnamon bark and banana peel extracts were 467 and 35 mg gallic acid equivalent/g extract, respectively. The flavonoid content found in banana peel and cinnamon bark extracts were 196 and 428 mg/g quercetin equivalent, respectively. In addition, it was found that cinnamon bark gave higher 2,2-Diphenyl-1-1 picryhydrazyl (DPPH) radical scavenging activity and total antioxidant activity (TAA). The antioxidant activity of the extracts was analyzed by measuring the peroxide and p-anisidine values after oxidation of fish oils, stored for a month (30 days) at 25 °C and showed lesser peroxide and p-anisidine values in the fish oils containing the sample extracts in comparison to the fish oil without containing any extract. The banana peel and cinnamon extracts had shown the ability as antioxidants to prevent the oxidation of fish oil and might be considered as rich sources of natural antioxidant.

  20. Coal pyrolysis under hydrogen-rich gases

    Energy Technology Data Exchange (ETDEWEB)

    Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

    1998-04-01

    To improve the economy of the pyrolysis process by reducing the hydrogen cost, it is suggested to use cheaper hydrogen-rich gases such as coke-oven gas (COG) or synthesis gas (SG) instead of pure hydrogen. The pyrolysis of Chinese Xianfeng lignite which was carried out with real COG and SG at 3-5 MPa, a final temperature of 650{degree}C and a heating rate of 5{degree}C/min in a 10g fixed-bed reactor is compared with coal pyrolysis with pure hydrogen and nitrogen under the same conditions. The results indicate that compared with hydropyrolysis at the same total pressure, the total conversion and tar yields from coal pyrolysis with COG and SG decreases while the unwanted water increases. However, at the same H{sub 2} partial pressure, the tar yields and yields of BBTX, PCX and naphthalene from the pyrolysis of coal with COG and SG are all significantly higher than those of hydropyrolysis. Therefore, it is possible to use COG and SG instead of pure hydrogen. 8 refs., 3 figs., 6 tabs.

  1. Combinatorial search for hydrogen storage alloys: Mg-Ni and Mg-Ni-Ti

    Energy Technology Data Exchange (ETDEWEB)

    Oelmez, Rabia; Cakmak, Guelhan; Oeztuerk, Tayfur [Dept. of Metallurgical and Materials Engineering, Middle East Technical University, 06531 Ankara (Turkey)

    2010-11-15

    A combinatorial study was carried out for hydrogen storage alloys involving processes similar to those normally used in their fabrication. The study utilized a single sample of combined elemental (or compound) powders which were milled and consolidated into a bulk form and subsequently deformed to heavy strains. The mixture was then subjected to a post annealing treatment, which brings about solid state reactions between the powders, yielding equilibrium phases in the respective alloy system. A sample, comprising the equilibrium phases, was then pulverized and screened for hydrogen storage compositions. X-ray diffraction was used as a screening tool, the sample having been examined both in the as processed and the hydrogenated state. The method was successfully applied to Mg-Ni and Mg-Ni-Ti yielding the well known Mg{sub 2}Ni as the storage composition. It is concluded that a partitioning of the alloy system into regions of similar solidus temperature would be required to encompass the full spectrum of equilibrium phases. (author)

  2. Effect of Biofertilizers on the Yield and Yield Components of Black Cumin (Nigella sativa L.

    Directory of Open Access Journals (Sweden)

    S Khorramdel

    2011-02-01

    Full Text Available Abstract Application of biological fertilizers is one of the most important methods for plant nutrition in ecological agriculture. In order to investigate the effect of biofertilizers on yield and yield components of black cumin (Nigella sativa L., a field experiment was arranged in a randomized complete block design with three replications during 2007 growing season at the Agricultural Research Station of Ferdowsi University of Mashhad. Treatments included: (A Azotobacter paspali, (B Azospirillum brasilense, (C the fungus of Glomus intraradaices, C+A, C+B, A+B, A+B+C, and control without no biofertilizers. In all treatments except control, the amounts of 15 mg of each biofertilizer were applied to 110 g of seeds. Results indicated that application of biofertilizers enhanced yield and yield components and decreased percentage of hollow capsules. Plant performance was better with application of Azospirillum plus mycorrhiza and a mixture of Azotobacter, Azospirillum and mycorrhiza in terms of yield determining criteria. The maximum and minimum amounts of seed yield were recorded in the B+C treatment with 41.4 gm-2, and control with 24.1 gm-2, respectively. There was no significant correlation between number of capsules per plant and seed yield, but the positive and significant correlation between number of branches per plant, number of seeds per capsule, 1000-seed weight and seed yield was observed. This study showed that application of suitable biofertilizers could increase yield and yield components of black cumin. Keywords: Biofertilizer, Ecological agriculture, Medicinal plants, Plant growth promoting rhizobacteria

  3. The microstructure and mechanical properties of Mg-3Al-3RE alloys

    International Nuclear Information System (INIS)

    Tian, X.; Wang, L.M.; Wang, J.L.; Liu, Y.B.; An, J.; Cao, Z.Y.

    2008-01-01

    The Mg-3Al-3RE alloys (RE, the cerium-rich or the yttrium-rich misch metal) were smelted in a resistance furnace under the protective flux from the Mg-RE master alloys and pure magnesium ingots. The microstructure and mechanical properties of samples prepared by steel mould casting method were investigated. Results show that the main phases of the alloys are α-Mg, Mg 17 Al 12 and Al-RE compounds, and the grain size reduced with the increasing content of the cerium-rich misch metal. Mg-3Al-2Ymm-1Cemm (Ymm, the yttrium-rich misch metal; Cemm, the Cerium-rich misch metal) exhibited the highest mechanical properties, that is UTS = 201 MPa and YS = 75 MPa, and ε = 8.2% at room temperature; UTS = 146 MPa, and YS = 70 MPa, ε = 18.2% at the temperature of 150 deg. C, respectively. Fracture surface analysis revealed that the Mg-3Al-2Ymm-1Cemm alloy has a mixed fracture feature at room temperature but ductile fracture at elevated temperature (150 deg. C)

  4. The feasibility of tunable p-type Mg doping in a GaN monolayer nanosheet

    International Nuclear Information System (INIS)

    Xia, Congxin; Peng, Yuting; Wei, Shuyi; Jia, Yu

    2013-01-01

    Based on density functional theory, the electronic structures, formation energy and transition energy level of a p-type Mg-doped GaN nanosheet are investigated. Numerical results show that the transition energy level decreases monotonously with increasing Mg doping concentration in Mg-doped GaN nanosheet systems, which is lower than that of the Mg-doped bulk GaN case. Moreover, the formation energy calculations indicate that Mg-doped GaN nanosheet structures can be realized under N-rich experimental growth conditions

  5. Myasthenia Gravis (MG): Medical Management

    Science.gov (United States)

    ... take effect, prior to surgery or for myasthenic crisis. However, some people receive regular plasmapheresis or IVIg as a supplement to immunosuppressant drugs. Pregnancy In rare cases, pregnancy appears to trigger the onset of MG. ...

  6. An Improved Cluster Richness Estimator

    Energy Technology Data Exchange (ETDEWEB)

    Rozo, Eduardo; /Ohio State U.; Rykoff, Eli S.; /UC, Santa Barbara; Koester, Benjamin P.; /Chicago U. /KICP, Chicago; McKay, Timothy; /Michigan U.; Hao, Jiangang; /Michigan U.; Evrard, August; /Michigan U.; Wechsler, Risa H.; /SLAC; Hansen, Sarah; /Chicago U. /KICP, Chicago; Sheldon, Erin; /New York U.; Johnston, David; /Houston U.; Becker, Matthew R.; /Chicago U. /KICP, Chicago; Annis, James T.; /Fermilab; Bleem, Lindsey; /Chicago U.; Scranton, Ryan; /Pittsburgh U.

    2009-08-03

    Minimizing the scatter between cluster mass and accessible observables is an important goal for cluster cosmology. In this work, we introduce a new matched filter richness estimator, and test its performance using the maxBCG cluster catalog. Our new estimator significantly reduces the variance in the L{sub X}-richness relation, from {sigma}{sub lnL{sub X}}{sup 2} = (0.86 {+-} 0.02){sup 2} to {sigma}{sub lnL{sub X}}{sup 2} = (0.69 {+-} 0.02){sup 2}. Relative to the maxBCG richness estimate, it also removes the strong redshift dependence of the richness scaling relations, and is significantly more robust to photometric and redshift errors. These improvements are largely due to our more sophisticated treatment of galaxy color data. We also demonstrate the scatter in the L{sub X}-richness relation depends on the aperture used to estimate cluster richness, and introduce a novel approach for optimizing said aperture which can be easily generalized to other mass tracers.

  7. Mg doping of GaN by molecular beam epitaxy

    International Nuclear Information System (INIS)

    Lieten, R R; Buchowicz, G; Dubon, O; Motsnyi, V; Zhang, L; Cheng, K; Leys, M; Degroote, S; Borghs, G

    2011-01-01

    We present a systematic study on the influence of growth conditions on the incorporation and activation of Mg in GaN layers grown by plasma-assisted molecular beam epitaxy. We show that high quality p-type GaN layers can be obtained on GaN-on-silicon templates. The Mg incorporation and the electrical properties have been investigated as a function of growth temperature, Ga : N flux ratio and Mg : Ga flux ratio. It was found that the incorporation of Mg and the electrical properties are highly sensitive to the Ga : N flux ratio. The highest hole mobility and lowest resistivity were achieved for slightly Ga-rich conditions. In addition to an optimal Ga : N ratio, an optimum Mg : Ga flux ratio was also observed at around 1%. We observed a clear Mg flux window for p-type doping of GaN : 0.31% 17 cm -3 and a mobility of 15 cm 2 V -1 s -1 . Temperature-dependent Hall effect measurements indicate an acceptor depth in these samples of 100 meV for a hole concentration of 5.5 x 10 17 cm -3 . The corresponding Mg concentration is 5 x 10 19 cm -3 , indicating approximately 1% activation at room temperature. In addition to continuous growth of Mg-doped GaN layers we also investigated different modulated growth procedures. We show that a modulated growth procedure has only limited influence on Mg doping at a growth temperature of 800 deg. or higher. This result is thus in contrast to previously reported GaN : Mg doping at much lower growth temperatures of 500 deg. C.

  8. Effect of Integrated Nutrient Management on Yield and Yield ...

    African Journals Online (AJOL)

    Declining soil fertility is one of the major problems causing yield reduction of barley ... (VC) with inorganic NP on growth, yield and yield components of food barley. ... The experiments were laid out in a randomized complete block design with ...

  9. Mg2FeH6 Synthesis Efficiency Map

    Directory of Open Access Journals (Sweden)

    Katarzyna Witek

    2018-02-01

    Full Text Available The influences of the processing parameters on the Mg2FeH6 synthesis yield were studied. Mixtures of magnesium hydride (MgH2 and iron (Fe were mechanically milled in a planetary ball mill under argon for 0.5-, 1-, 2- and 3-h periods and subsequently sintered at temperatures from 300–500 ∘ C under hydrogen. The reaction yield, phase content and hydrogen storage properties of the received materials were investigated. The morphologies of the powders after synthesis were studied by SEM. The synthesis effectiveness map was presented. The obtained results prove that synthesis parameters, such as the milling time and synthesis temperature, greatly influence the reaction yield and material properties and show that extended mechanical milling may not be beneficial to the reaction efficiency.

  10. Positron annihilation study of formation of Mg vacancy in MgO

    International Nuclear Information System (INIS)

    Mizuno, M.; Araki, H.; Shirai, Y.; Inoue, Y.; Sugita, K.; Mizoguchi, T.; Tanaka, I.; Adachi, H.

    2004-01-01

    We have investigated the formation of Mg vacancy induced by ultra-dilute trivalent impurities in MgO by a combination of positron annihilation measurement and theoretical calculations of positron lifetimes. The undoped MgO yields the shortest positron lifetime of 130 ps that is shorter than that of 166 ps previously reported using a single crystal sample. The positron lifetime of the doped samples increases with the increase of the Al or Ga dopant concentration and is saturated at around 170 ps. This result indicates that the previously reported value of 166 ps is ascribed to not the bulk but the vacancy state induced by impurities. The experimental bulk lifetime of 130 ps, which is obtained by employing trapping model, is well reproduced by the theoretical calculation using the semiconductor model. The calculated defect lifetime is about 20 ps longer than the experimental value. This may be due to the lattice relaxation around Mg vacancy associated with the trapping of positrons. (orig.)

  11. Positron annihilation study of formation of Mg vacancy in MgO

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, M.; Araki, H.; Shirai, Y. [Science and Technology Center for Atoms, Molecules and Ions Control, Osaka Univ., Osaka (Japan); Inoue, Y.; Sugita, K. [Dept. of Materials Science and Engineering, Osaka Univ., Osaka (Japan); Mizoguchi, T.; Tanaka, I.; Adachi, H. [Dept. of Materials Science and Engineering, Kyoto Univ., Kyoto (Japan)

    2004-07-01

    We have investigated the formation of Mg vacancy induced by ultra-dilute trivalent impurities in MgO by a combination of positron annihilation measurement and theoretical calculations of positron lifetimes. The undoped MgO yields the shortest positron lifetime of 130 ps that is shorter than that of 166 ps previously reported using a single crystal sample. The positron lifetime of the doped samples increases with the increase of the Al or Ga dopant concentration and is saturated at around 170 ps. This result indicates that the previously reported value of 166 ps is ascribed to not the bulk but the vacancy state induced by impurities. The experimental bulk lifetime of 130 ps, which is obtained by employing trapping model, is well reproduced by the theoretical calculation using the semiconductor model. The calculated defect lifetime is about 20 ps longer than the experimental value. This may be due to the lattice relaxation around Mg vacancy associated with the trapping of positrons. (orig.)

  12. Effect of Mg Doping on the Photoluminescence of GaN:Mg Films by Radio-Frequency Plasma-Assisted Molecular Beam Epitaxy

    International Nuclear Information System (INIS)

    Sui Yan-Ping; Yu Guang-Hui

    2011-01-01

    We investigate undoped GaN and Mg-doped GaN grown by rf plasma-assisted molecular beam epitaxy (MBE) with different Mg concentrations by photoluminescence (PL) at low temperature, Hall-effect and XRD measurements. In the PL spectra of lightly Mg-doped GaN films, a low intensity near band edge (NBE) emission and strong donor-acceptor pair (DAP) emission with its phonon replicas are observed. As the Mg concentration is increased, the DAP and NBE bands become weaker and a red shift of these bands is observed in the PL spectra. Yellow luminescence (YL) is observed in heavily Mg-doped GaN. The x-ray diffraction is employed to study the structure of the films. Hall measurement shows that there is a maximum value (3.9 × 10 18 cm −3 ) of hole concentration with increasing Mg source temperature for compensation effect. PL spectra of undoped GaN are also studied under N-rich and Ga-rich growth conditions. Yellow luminescences of undoped Ga-rich GaN and heavily Mg-doped GaN are compared, indicating the different origins of the YL bands. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  13. Yield enhancement with DFM

    Science.gov (United States)

    Paek, Seung Weon; Kang, Jae Hyun; Ha, Naya; Kim, Byung-Moo; Jang, Dae-Hyun; Jeon, Junsu; Kim, DaeWook; Chung, Kun Young; Yu, Sung-eun; Park, Joo Hyun; Bae, SangMin; Song, DongSup; Noh, WooYoung; Kim, YoungDuck; Song, HyunSeok; Choi, HungBok; Kim, Kee Sup; Choi, Kyu-Myung; Choi, Woonhyuk; Jeon, JoongWon; Lee, JinWoo; Kim, Ki-Su; Park, SeongHo; Chung, No-Young; Lee, KangDuck; Hong, YoungKi; Kim, BongSeok

    2012-03-01

    A set of design for manufacturing (DFM) techniques have been developed and applied to 45nm, 32nm and 28nm logic process technologies. A noble technology combined a number of potential confliction of DFM techniques into a comprehensive solution. These techniques work in three phases for design optimization and one phase for silicon diagnostics. In the DFM prevention phase, foundation IP such as standard cells, IO, and memory and P&R tech file are optimized. In the DFM solution phase, which happens during ECO step, auto fixing of process weak patterns and advanced RC extraction are performed. In the DFM polishing phase, post-layout tuning is done to improve manufacturability. DFM analysis enables prioritization of random and systematic failures. The DFM technique presented in this paper has been silicon-proven with three successful tape-outs in Samsung 32nm processes; about 5% improvement in yield was achieved without any notable side effects. Visual inspection of silicon also confirmed the positive effect of the DFM techniques.

  14. Compositional variations of chromiferous spinel in Mg-rich rocks of ...

    Indian Academy of Sciences (India)

    tions typical of spinels found in mid-ocean ridge basalts. ... composition of the source region of the magmas ... The Deccan Traps, one of the largest continen- tal LIPs ... outcrops in the Seychelles Islands (Mahoney 1988; ...... Beane J E 1994 A role for lower continental crust in flood ... magmatic evolution; J. Asian Earth Sci.

  15. Using CaO- and MgO-rich industrial waste streams for carbon sequestration

    International Nuclear Information System (INIS)

    Stolaroff, Joshuah K.; Lowry, Gregory V.; Keith, David W.

    2005-01-01

    To prevent rapid climate change, it will be necessary to reduce net anthropogenic CO 2 emissions drastically. This likely will require imposition of a tax or tradable permit scheme that creates a subsidy for negative emissions. Here, we examine possible niche markets in the cement and steel industries where it is possible to generate a limited supply of negative emissions (carbon storage or sequestration) cost-effectively. Ca(OH) 2 and CaO from steel slag or concrete waste can be dissolved in water and reacted with CO 2 in ambient air to capture and store carbon safely and permanently in the form of stable carbonate minerals (CaCO 3 ). The kinetics of Ca dissolution for various particle size fractions of ground steel slag and concrete were measured in batch experiments. The majority of available Ca was found to dissolve on a time scale of hours, which was taken to be sufficiently fast for use in an industrial process. An overview of the management options for steel slag and concrete waste is presented, which indicates how their use for carbon sequestration might be integrated into existing industrial processes. Use of the materials in a carbon sequestration scheme does not preclude subsequent use and is likely to add value by removing the undesirable qualities of water absorption and expansion from the products. Finally, an example scheme is presented which could be built and operated with current technology to sequester CO 2 with steel slag or concrete waste. Numerical models and simple calculations are used to establish the feasibility and estimate the operating parameters of the scheme. The operating cost is estimated to be US$8/t-CO 2 sequestered. The scheme would be important as an early application of technology for capturing CO 2 directly from ambient air

  16. Adaptive Reactive Rich Internet Applications

    Science.gov (United States)

    Schmidt, Kay-Uwe; Stühmer, Roland; Dörflinger, Jörg; Rahmani, Tirdad; Thomas, Susan; Stojanovic, Ljiljana

    Rich Internet Applications significantly raise the user experience compared with legacy page-based Web applications because of their highly responsive user interfaces. Although this is a tremendous advance, it does not solve the problem of the one-size-fits-all approach1 of current Web applications. So although Rich Internet Applications put the user in a position to interact seamlessly with the Web application, they do not adapt to the context in which the user is currently working. In this paper we address the on-the-fly personalization of Rich Internet Applications. We introduce the concept of ARRIAs: Adaptive Reactive Rich Internet Applications and elaborate on how they are able to adapt to the current working context the user is engaged in. An architecture for the ad hoc adaptation of Rich Internet Applications is presented as well as a holistic framework and tools for the realization of our on-the-fly personalization approach. We divided both the architecture and the framework into two levels: offline/design-time and online/run-time. For design-time we explain how to use ontologies in order to annotate Rich Internet Applications and how to use these annotations for conceptual Web usage mining. Furthermore, we describe how to create client-side executable rules from the semantic data mining results. We present our declarative lightweight rule language tailored to the needs of being executed directly on the client. Because of the event-driven nature of the user interfaces of Rich Internet Applications, we designed a lightweight rule language based on the event-condition-action paradigm.2 At run-time the interactions of a user are tracked directly on the client and in real-time a user model is built up. The user model then acts as input to and is evaluated by our client-side complex event processing and rule engine.

  17. Willow yield is highly dependent on clone and site

    DEFF Research Database (Denmark)

    Ugilt Larsen, Søren; Jørgensen, Uffe; Lærke, Poul Erik

    2014-01-01

    Use of high-yielding genotypes is one of the means to achieve high yield and profitability in willow (Salix spp.) short rotation coppice. This study investigated the performance of eight willow clones (Inger, Klara, Linnea, Resolution, Stina, Terra Nova, Tora, Tordis) on five Danish sites......, differing considerably in soil type, climatic conditions and management. Compared to the best clone, the yield was up to 36 % lower for other clones across sites and up to 51 % lower within sites. Tordis was superior to other clones with dry matter yields between 5.2 and 10.2 Mg ha−1 year−1 during the first...... 3-year harvest rotation, and it consistently ranked as the highest yielding clone on four of the five sites and not significantly lower than the highest yielding clone on the fifth site. The ranking of the other clones was more dependent on site with significant interaction between clone and site...

  18. Bulk yields of nucleosynthesis from massive stars

    International Nuclear Information System (INIS)

    Arnett, W.D.

    1978-01-01

    Preliminary estimates are made of the absolute yields of abundant nuclei synthesized in observed stars. The compositions of nine helium stars of mass 3 or =10M/sub sun/ is estimated. A variety of choices for the initial mass function (IMF) are used to calculate the yield per stellar generation. For standard choices of the (IMF) the absolute and relative yields of 12 C, 16 O, 20 Ne, 24 Mg, the Si to Ca group, and the iron group agree with solar system values, to the accuracy of the calculations. The relative yields are surprisingly insensitive to the slope of the IMF. In a second approach, using standard estimates (Ostriker, Richstone, and Thuan) for the current rate of stellar death, I find the present rate of nucleosynthesis in the solar neighborhood to be about 10%of the average rate over galactic history. This result is consistent with many standard models of galactic evolution (for example, the Schmidt model in which star formation goes as gas density squared). It appears that if the star formation rate is high enough to produce the stars we see around us, then the nucleosynthesis rate is large enough to produce the processed nuclei (except 4 He) seen in those stars. The typical nucleosynthesis source is massive (Mapprox. =30 M/sub sun/); the death rate of such stars is a small fraction (3-10%) of recent estimates of the total rate of supernovae

  19. A note on hypoplastic yielding

    OpenAIRE

    Nader, José Jorge

    2010-01-01

    This note discusses briefly the definition of yield surface in hypoplasticity in connection with the physical notion of yielding. The relation of yielding with the vanishing of the material time derivative of the stress tensor and the vanishing of the corotational stress rate is investigated.

  20. Effect of heat treatment on the microstructures and damping properties of biomedical Mg-Zr alloy

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, Ming-Hung [Department of Mechanical Engineering and Graduate Institute of Mechanical and Precision Engineering, National Kaoshiung University of Applied Sciences, Kaoshiung 807, Taiwan (China); Department of Dentistry, Chang Yin dental clinic, No.46-1, Yangming St., Banqiao City, Taipei County 220, Taiwan (China); Research Center for Biomedical Devices, Taipei Medical University, Taipei 110, Taiwan (China); Chen, May-Show [Research Center for Biomedical Devices, Taipei Medical University, Taipei 110, Taiwan (China); School of Oral Hygiene, College of Oral Medicine, Taipei Medical University, Taipei 110, Taiwan (China); Department of Dentistry, Taipei Medical University Hospital, Taipei 110, Taiwan (China); Lin, Ling-Hung [Department of Dentistry, Taipei Medical University Hospital, Taipei 110, Taiwan (China); School of Dentistry, College of Oral Medicine, Taipei Medical University, Taipei 110, Taiwan (China); Lin, Ming-Hong [Department of Mechanical Engineering and Graduate Institute of Mechanical and Precision Engineering, National Kaoshiung University of Applied Sciences, Kaoshiung 807, Taiwan (China); Wu, Ching-Zong, E-mail: chinaowu@tmu.edu.tw [Department of Dentistry, Taipei Medical University Hospital, Taipei 110, Taiwan (China); School of Dentistry, College of Oral Medicine, Taipei Medical University, Taipei 110, Taiwan (China); Ou, Keng-Liang, E-mail: klou@tmu.edu.tw [Research Center for Biomedical Devices, Taipei Medical University, Taipei 110, Taiwan (China); Graduated Institute of Biomedical Materials and Engineering, Taipei Medical University, Taipei 110, Taiwan (China); Research Center for Biomedical Implants and Microsurgery Devices, Taipei Medical University, Taipei 110, Taiwan (China); Yu, Chih-Hua [Research Center for Biomedical Devices, Taipei Medical University, Taipei 110, Taiwan (China); Research Center for Biomedical Implants and Microsurgery Devices, Taipei Medical University, Taipei 110, Taiwan (China)

    2011-01-21

    Research highlights: > When the as-quenched Mg-1Zr alloy was aged at temperatures ranging from 200 deg. C to 500 deg. C, a microstructural transformation sequence was found to be {alpha}-Mg {yields} ({alpha}-Mg + twin{sub dense}) {yields} ({alpha}-Mg + twin{sub loose}) {yields} ({alpha}-Mg + {alpha}-Zr). > As the as-quenched Mg-1Zr alloy was subjected to aging treatment at 300 deg. C for 16 h, it exhibited the maximum damping properties. > The twin structure plays a crucial role in increasing the damping capacity of the Mg-1Zr alloy. - Abstract: In this study, we elucidated the effect of heat treatment on the microstructures and damping properties of the biomedical Mg-1 wt% Zr (K1) alloy by optical microscopy, transmission electron microscopy, energy-dispersive X-ray spectrometry, and experimental model analysis. The following microstructural transformation occurred when the as-quenched (AQ, i.e., solution heat treated and quenched) K1 alloy was subjected to aging treatment in the temperature range 200-500 deg. C: {alpha}-Mg {yields} ({alpha}-Mg + twin{sub dense}) {yields} ({alpha}-Mg + twin{sub loose}) {yields} ({alpha}-Mg + {alpha}-Zr). This microstructural transformation was accompanied by variations in the damping capacity. The damping properties of the AQ K1 alloy subjected to aging treatment at 300 deg. C for 16 h were the best among those of the alloys investigated in the present study. The presence of twin structures in the alloy matrix was thought to play a crucial role in increasing the damping capacity of the K1 alloy. Hence, we state that a combination of solution treatment and aging is an effective means of improving the damping capacity of biomedical K1 alloys.

  1. H2-rich fluids from serpentinization: Geochemical and biotic implications

    OpenAIRE

    Sleep, N. H.; Meibom, A.; Fridriksson, Th.; Coleman, R. G.; Bird, D. K.

    2004-01-01

    Metamorphic hydration and oxidation of ultramafic rocks produces serpentinites, composed of serpentine group minerals and varying amounts of brucite, magnetite, and/or FeNi alloys. These minerals buffer metamorphic fluids to extremely reducing conditions that are capable of producing hydrogen gas. Awaruite, FeNi3, forms early in this process when the serpentinite minerals are Fe-rich. Olivine with the current mantle Fe/Mg ratio was oxidized during serpentinization after the Moon-forming impac...

  2. Effect of Aluminum Addition on the Evolution of Microstructure, Crystallographic Texture and Mechanical Properties of Single Phase Hexagonal Close Packed Mg-Li Alloys

    Science.gov (United States)

    Bhagat Singh, P.; Sabat, R. K.; Kumaran, S.; Suwas, S.

    2018-02-01

    In the present investigation, an effort has been made to understand the effect of aluminum addition to α Mg-Li alloys. The corresponding composition Mg-4Li- xAl ( x = 0, 2, 4 and 6 wt.%) alloys have been prepared by stir casting route under an argon environment. Extrusion was carried out at 300 °C with the extrusion ratio of 15:1. Significant grain refinement was observed after extrusion. X-ray diffraction-based investigation of the cast and extruded alloys showed the presence of intermetallic compounds such as Mg17Al12 and AlLi in the Al-rich alloys namely, Mg-4Li- xAl ( x = 4 and 6 wt.%). These precipitates were also present in the extruded plus annealed samples, indicating the stability of the precipitates at high temperature. The bulk x-ray texture measurement revealed a crystallographic texture where the c-axis of the h.c.p crystals was perpendicular to the extrusion direction (ED) for extruded sample. A texture transition was observed on annealing. The c-axis was oriented parallel to the ED. Mechanical properties of the cast, extruded and extruded plus annealed material illustrate that the addition of Al led to enhancement in hardness, yield strength and ultimate tensile strength.

  3. Optical absorption and thermoluminescence in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature; Absorcion optica y termoluminiscencia en MgO, MgO:Ni y MgO:Li irradiados a temperatura ambiente

    Energy Technology Data Exchange (ETDEWEB)

    Delgado, L

    1984-07-01

    Optical absorption and thermoluminescence (TL) studies in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature are presented. In pure Mg O the thermal annihilation of Fe3+ by recombination with thermally released electrons at {approx} 90 and 175 degree centigree and the V center annealing by hole release up to 100 degree centigree cause the observed glow peaks at these temperatures. The TL excitation spectrum shows two maxima at 245 nm (electron center) and 288 nm (Fe3+). In Mg O:Ni X irradiation induces Fe{sup 2}+ {yields}- Fe{sup 3}+ and Ni{sup 2}+ {yields} Ni{sup 3}+ oxidations. Two TL emission bands centered at 110 degree centigree (red) and 80 o{sup C} (green) are assigned to electron release and their recombination at Fe{sup 3}+ and Ni{sup 3}+ respectively. In Mg O:Li two TL emission bands, one blue (430 nm) and the other red (730 nm) with excitation maxima at 245 nm (electron center) and 200 nm (hole center) respectively are observed. No V-center formation was detected in both Ni and Li doped samples. (Author) 42 refs.

  4. The role of natural organic matter in nitrite formation by LP-UV/H2O2 treatment of nitrate-rich water.

    Science.gov (United States)

    Semitsoglou-Tsiapou, Sofia; Mous, Astrid; Templeton, Michael R; Graham, Nigel J D; Hernández Leal, Lucía; Kruithof, Joop C

    2016-12-01

    The role of natural organic matter (NOM) on nitrite formation from nitrate photolysis by low pressure ultraviolet lamp (LP-UV) photolysis and LP-UV/H 2 O 2 treatment was investigated. Nitrate levels up to the WHO guideline maximum of 50 mg NO 3 - /L were used in tests. The presence of 4 mg/L Suwannee River natural organic matter (NOM) led to increased nitrite yields compared to NOM-free controls. This was caused partly by NOM scavenging of OH radicals, preserving the produced NO 2 - as well as the ONOO - that leads to NO 2 - formation, but also via the production of radical species ( 1 O 2 , O 2 - and OH) by the photolysis of NOM. In addition, solvated electrons formed by NOM photolysis may reduce nitrate directly to nitrite. For comparison, Nordic Lake NOM, representative of aquatic NOM, as well as Pony Lake NOM, which had a greater nitrogen content (6.51% w/w) than the other two types of NOM, were investigated, yielding similar nitrite levels as Suwannee River NOM. The results suggest that neither the type nor the nitrogen content of the NOM have an effect on the nitrite yields obtained over the range of UV/H 2 O 2 doses applied (UV fluences of 500-2100 mJ/cm 2 and hydrogen peroxide doses of 10, 25, and 50 mg/L). The findings indicate that for UV fluences above 1500 mJ/cm 2 the resulting nitrite concentration can exceed the 0.1 mg/L EU regulatory limit for nitrite, suggesting that nitrite formation by LP-UV advanced oxidation of nitrate-rich waters is important to consider. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. MgO encapsulated mesoporous zeolite for the side chain alkylation of toluene with methanol.

    Science.gov (United States)

    Jiang, Nanzhe; Jin, Hailian; Jeong, Eun-Young; Park, Sang-Eon

    2010-01-01

    Side chain alkylation of toluene with methanol was studied over mesoporous zeolite supported MgO catalysts. MgO were supported onto the carbon templated mesoporous silicalite-1 by direct synthesis route under microwave conditions. This direct synthesis route yields the majority of MgO highly dispersed into the mesopores of the silicalite-1 crystals. The vapor phase alkylation of toluene with methanol was performed over these catalysts under vapor phase conditions at atmospheric pressure. Mesoporous silicalite-1 supported MgO catalysts gave improved yields towards side chain alkylated products compared to the bulk MgO. The higher activity exhibited by 5% MgO supported on mesoporous silicalite compared to the one with 1% MgO can be attributed to the large number of weak basic sites observed from the CO2 TPD.

  6. Experimental investigation and thermodynamic calculation of the Mg-Sr-Zr system

    International Nuclear Information System (INIS)

    Zhou, Hua; Chen, Chong; Du, Yong; Central South Univ., Hunan; Gong, Haoran

    2016-01-01

    Both experimental investigation and thermodynamic calculation were performed for the Mg-Sr-Zr system. Four decisive alloys were firstly selected and prepared using a powder metallurgy method to measure the isothermal section at 400 C via a combination of X-ray diffraction and electron probe microanalysis. No ternary compound has been observed for this ternary system. Four three-phase regions, (Mg) + (αZr) + Mg 17 Sr 2 , Mg 17 Sr 2 + (αZr) + Mg 38 Sr 9 , Mg 38 Sr 9 + (αZr) + Mg 23 Sr 6 , and Mg 23 Sr 6 + (αZr) + Mg 2 Sr, have been identified at 400 C. No appreciable ternary solubility has been detected in the binary Mg-Sr compounds. Phase transition temperatures of the Mg-Sr-Zr alloys were measured by means of differential scanning calorimetry. The thermodynamic calculations match well with the experimental data in the present work, indicating that no ternary thermodynamic parameters are needed for the thermodynamic description of this ternary system. In order to verify the reliability of the current thermodynamic calculations of the Mg-Sr-Zr system, eight as-cast alloys in the Mg-rich corner were also prepared. The calculated liquidus projection is consistent with the observed primary phase regions. The present thermodynamic calculations are reliable and can be used in the development of Mg alloys.

  7. Powder metallurgical low-modulus Ti-Mg alloys for biomedical applications.

    Science.gov (United States)

    Liu, Yong; Li, Kaiyang; Luo, Tao; Song, Min; Wu, Hong; Xiao, Jian; Tan, Yanni; Cheng, Ming; Chen, Bing; Niu, Xinrui; Hu, Rong; Li, Xiaohui; Tang, Huiping

    2015-11-01

    In this work, powder metallurgical (PM) Ti-Mg alloys were prepared using combined techniques of mechanical alloying and spark plasma sintering. The alloys mainly consist of super saturations of Mg in Ti matrix, and some laminar structured Ti- and Mg-rich phases. The PM Ti-Mg alloys contain a homogeneous mixtures of nanocrystalline Mg and Ti phases. The novel microstructures result in unconventional mechanical and biological properties. It has been shown that the PM Ti-Mg alloys have a much lower compression modulus (36-50GPa) compared to other Ti alloys, but still remain a very high compressive strength (1500-1800MPa). In addition, the PM Ti-Mg alloys show good biocompatibility and bioactivity. Mg can dissolve in the simulated body fluids, and induce the formation of the calcium phosphate layer. The compression modulus of PM Ti-Mg alloys decreases with the amount of Mg, while the bioactivity increases. Although the corrosion resistance of Ti-Mg alloys decreases with the content of Mg, the alloys still show good stability in simulated body fluid under electrochemical conditions. The indirect and direct cytotoxicity results show that PM Ti-Mg alloys have a good biocompatibility to NIH-3T3 cells. Therefore, the PM Ti-Mg alloys are promising candidates in biomedical applications. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. The Abundance of Mg in the Interstellar Medium

    Science.gov (United States)

    Fitzpatrick, Edward L.

    1997-06-01

    An empirical determination of the f-values of the far-UV Mg II λλ1239, 1240 lines is reported. The strong near-UV Mg II λλ2796, 2803 lines are generally highly saturated along most interstellar sight lines outside the local interstellar medium (ISM) and usually yield extremely uncertain estimates of Mg+ column densities in interstellar gas. Since Mg+ is the dominant form of Mg in the neutral ISM, and since Mg is expected to be a significant constituent of interstellar dust grains, the far-UV lines are critical for assessing the role of this important element in the ISM. This study consists of complete component analyses of the absorption along the lines of sight toward HD 93521 in the Galactic halo and ξ Persei and ζ Ophiuchi in the Galactic disk, including all four UV Mg+ lines and numerous other transitions. The three analyses yield consistent determinations of the λλ1239, 1240 f-values, with weighted means of (6.4 +/- 0.4) × 10-4 and (3.2 +/- 0.2) × 10-4, respectively. These results are a factor of ~2.4 larger than a commonly used theoretical estimate, and a factor of ~2 smaller than a recently suggested empirical revision. The effects of this result on gas- and dust-phase abundance measurements of Mg are discussed. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, under NASA contract NAS5-2655. This Letter is dedicated to the memory of Professor Lyman Spitzer Jr. He was a great guy.

  9. Interface Promoted Reversible Mg Insertion in Nanostructured Tin-Antimony Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Yingwen; Shao, Yuyan; Parent, Lucas R.; Sushko, Maria L.; Li, Guosheng; Sushko, Petr; Browning, Nigel D.; Wang, Chong M.; Liu, Jun

    2015-11-11

    This paper demonstrates intermetallic compounds SnSb are highly active materials for reversibly hosting Mg ions. Compared with monometallic Sn and Sb, SnSb alloy exhibited exceptionally high reversible capacity (420 mAh/g), excellent rate capability and good cyclic stability. Mg insertion into pristine SnSb involves an activation process to complete, which induces particle breakdown and results in phase segregation to Sn-rich and Sb-rich phases. Both experimental analysis and DFT simulation suggest that the Sn-rich phase is particularly active and provides most of the capacity whereas the Sb-rich phase is not as active, and the interface between these two phases play a key role in promoting the formation and stabilization of the cubic Sn phase that is more favorable for fast and reversible Mg insertion. We further show that activated SnSb alloy has good compatibility with simple Mg electrolytes. Overall, this work could provide new approaches for designing materials capable of reversible Mg ion insertion and new opportunities for understanding Mg electrochemistry.

  10. Yield and nutrient composition of biochar produced from different feedstocks at varying pyrolytic temperatures

    International Nuclear Information System (INIS)

    Naeem, M.A.; Khalid, M.; Arshad, M.; Ahmad, R.

    2014-01-01

    Variation in pyrolytic temperatures and feedstocks affects the yield and nutrient composition of biochar. Selection of suitable feedstock and optimum pyrolytic temperature is crucial before using it for agricultural purposes. We compared biochars produced from two feedstocks (wheat straw and rice) at three temperatures (300, 400 and 500 degree C). Biochar yield decreased significantly (p<0.05) with increasing pyrolysis temperature, while ash contents were increased. The cation exchange capacity was significantly higher (119 cmolc kg/sup -1/) at temperature 400 degree C. The pH, electrical conductivity (EC) and carbon content of biochars increased significantly with increasing temperature and maximum pH (10.4) and EC (3.35 dS m/sup -1/) were observed in rice straw biochar (WSB) at 500 degree C and carbon content (662 g kg/sup -1/) in wheat straw biochar (RSB) at 500 degree C. Concentration of phosphorus (P) and potassium (K) increased significantly with increasing temperature, while of nitrogen (N) decreased. Overall, the maximum N (13.8 g kg/sup -1/at 300 degree C) and P (3.4 g kg/sup -1/at 500 degree C) concentrations were observed in WSB while, maximum K (48 g kg/sup -1/ at 500 degree C)in RSB. High pyrolysis temperature reduced AB-DTPA extractable nutrients (expect Mn). The highest AB-DTPA extractable nutrients such as P (113 mg kg/sup -1/) and Ca (1.07 g kg/sup -1/) were observed in WSB at 300 degree C while, K (18 g kg/sup -1/) and magnesium (Mg) (1.55 g kg/sup -1/) in RSB at 300 degree C. Selected feedstock and use of low pyrolysis temperature may produce nutrient-rich biochar, with high CEC and low pH and these could have positive effects on calcareous soils. (author)

  11. Recovery of methane-rich gas from solid-feed anaerobic digestion of ipomoea (Ipomoea carnea).

    Science.gov (United States)

    Sankar Ganesh, P; Sanjeevi, R; Gajalakshmi, S; Ramasamy, E V; Abbasi, S A

    2008-03-01

    Studies are presented on new types of anaerobic digesters in which chopped or dry crushed Ipomoea carnea was fed without any other pretreatment, in an attempt to develop commercially viable means of utilizing the otherwise very harmful plant. Two types of solid-feed anaerobic digesters (SFADs) were studied. The first type had a single vessel in which the bottom 35% portion was separated from the top portion by a perforated PVC disk. The weed was charged from the top and inoculated with anaerobically digested cowdung-water slurry. The fermentation of the weed in the reactor led to the formation of volatile fatty acids (VFAs) plus some biogas. The leachate, rich in the VFAs, was passed through the perforated PVC sheet and collected in the lower portion of the vessel. The other type of reactors had two vessels, the first one was fully charged with the weed and the second received the VFA leachate. With both types were attached upflow anaerobic filters (UAFs) which converted the leachate into combustible biogas consisting of approximately 70% methane. All SFADs developed very consistent performance in terms of biogas yield within 17 weeks of start. The two-compartment reactors yielded significantly more biogas than the single-compartment reactors of corresponding total volume, and the reactors with which anaerobic filters (AF) were attached yielded more biogas than the ones without AF. The best performing units generated 2.41m(3) of biogas per m(3) of digester volume, as compared to 0.1-0.2m(3) of biogas, m(-3)d(-1), obtainable with conventional digesters. This indicates the viability of this technology. The spent weed can be vermicomposted directly to obtain good soil-conditioner cum fertilizer; earthworm Eudrilus eugeniae produced 540mg vermicast per animal every day, achieving near total conversion of feed to vermicast in 20 days. The proposed systems, thus, makes it possible to accomplish total utilization of ipomoea.

  12. The natural aging and precipitation hardening behaviour of Al-Mg-Si-Cu alloys with different Mg/Si ratios and Cu additions

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Lipeng [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 China (China); Jia, Zhihong, E-mail: zhihongjia@cqu.edu.cn [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 China (China); Zhang, Zhiqing; Sanders, Robert E.; Liu, Qing [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 China (China); Yang, Guang [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education and International Centre for Dielectric Research, Xi’an Jiaotong University, Xi’an 710049 (China)

    2015-03-11

    The natural aging and artificial aging behaviours of Al-Mg-Si-Cu alloys with different Mg/Si ratios and Cu additions were investigated using Vickers microhardness measurements, differential scanning calorimetry (DSC) analysis and transmission electron microscopy (TEM) characterisation. Excess Si and Cu additions enhanced the alloy hardening ability during natural (NA) and artificial aging (AA). Alloys with low Cu and high Si contents exhibited higher precipitation hardening than alloys rich in Mg during artificial aging. In contrast, the alloys with high amounts of Cu were less dependent on the Mg/Si ratio during precipitation hardening due to their similar aging kinetics. The main precipitate phases that contributed to the peak-aging hardness were the L, Q′ and β″ phases. In the over-aging conditions, the alloys rich in Mg and Cu had finer and more numerous precipitates than their Si-rich equivalents due to the preferential precipitation of the L phase. The combination of excess Mg and high Cu resulted in an alloy with a relatively low hardness in T4 temper and a relatively higher hardness after the paint baking cycle. Thus, this alloy has good potential for use in auto body panel applications.

  13. Synthesis of Mg(OH)2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

    Energy Technology Data Exchange (ETDEWEB)

    Tran, P.X.; Howard, B.H.; Martello, D.V.; Soong, Y.; Chyu, M.K.

    2008-01-01

    laser ablation of magnesium in deionized water (OW), solutions of OW and sodium dodecyl sulfate (50S) with different concentrations, acetone and 2-propanol has been conducted, The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alterationj decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH)2 particles were mainly produced by laser ablation of Mg in either OW or OW~SOS solutions. Ablation in OW yielded particles of fiber-like shapes having a diameter of about 5-lOnm and length as long as 150nm. Materials produced in DW-SOS solutions were composed of various size and shape particles, Some had rough surfaces with irregular shapes. Small particles were about 20-30nm and larger particles were about 120 nm. Particles with rod-like, triangular, and plate-like shapes were also observed.

  14. Synthesis of Mg(OH)2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

    Energy Technology Data Exchange (ETDEWEB)

    Phuoc, Tran X. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Howard, Bret. H. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Martello, Donald V. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Soong, Yee [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Chyu, Minking K. [Univ. of Pittsburgh, PA (United States)

    2008-11-01

    Laser ablation of magnesium in deionized water (DW), solutions of DW and sodium dodecyl sulfate (SDS) with different concentrations, acetone and 2-propanol has been conducted. The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alteration/decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH)2 particles were mainly produced by laser ablation of Mg in either DW or DW-SDS solutions. Ablation in DW yielded particles of fiber-like shapes having a diameter of about 5-10nm and length-as long as 150 nm. Materials produced in DW-SDS solutions were composed of various size and shape particles. Some had rough surfaces with irregular shapes. Small particles were about 20-30 nm and larger particles were about 120 nm. Particles with rodlike, triangular, and plate-like shapes were also observed.

  15. Synthesis of Mg(OH) 2, MgO, and Mg nanoparticles using laser ablation of magnesium in water and solvents

    Science.gov (United States)

    Phuoc, Tran X.; Howard, Bret. H.; Martello, Donald V.; Soong, Yee; Chyu, Minking K.

    2008-11-01

    Laser ablation of magnesium in deionized water (DW), solutions of DW and sodium dodecyl sulfate (SDS) with different concentrations, acetone and 2-propanol has been conducted. The results showed that ablation in acetone and 2-propanol yielded MgO and Mg nanocrystallites as isolated particles and agglomerated chains probably intermixed with organic residues resulting from the alteration/decomposition of the solvents under the high-energy conditions. Brucite-like Mg(OH) 2 particles were mainly produced by laser ablation of Mg in either DW or DW-SDS solutions. Ablation in DW yielded particles of fiber-like shapes having a diameter of about 5-10 nm and length as long as 150 nm. Materials produced in DW-SDS solutions were composed of various size and shape particles. Some had rough surfaces with irregular shapes. Small particles were about 20-30 nm and larger particles were about 120 nm. Particles with rod-like, triangular, and plate-like shapes were also observed.

  16. The STAR-RICH Detector

    CERN Document Server

    Lasiuk, B; Braem, André; Cozza, D; Davenport, M; De Cataldo, G; Dell'Olio, L; Di Bari, D; Di Mauro, A; Dunlop, J C; Finch, E; Fraissard, Daniel; Franco, A; Gans, J; Ghidini, B; Harris, J W; Horsley, M; Kunde, G J; Lasiuk, B; Lesenechal, Y; Majka, R D; Martinengo, P; Morsch, Andreas; Nappi, E; Paic, G; Piuz, François; Posa, F; Raynaud, J; Salur, S; Sandweiss, J; Santiard, Jean-Claude; Satinover, J; Schyns, E M; Smirnov, N; Van Beelen, J; Williams, T D; Xu, Z

    2002-01-01

    The STAR-RICH detector extends the particle idenfication capabilities of the STAR spectrometer for charged hadrons at mid-rapidity. It allows identification of pions and kaons up to ~3 GeV/c and protons up to ~5 GeV/c. The characteristics and performance of the device in the inaugural RHIC run are described.

  17. SOFTWARE SUPPORT FOR RICH PICTURES

    DEFF Research Database (Denmark)

    Valente, Andrea; Marchetti, Emanuela

    2010-01-01

    Rich pictures (RP) are common in object-oriented analysis and design courses, but students seem to have problems in integrating them in their projects' workflow. A new software tool is being developed, specific for RP authoring. To better understand students' issues and working practice with RP...

  18. Ternary particle yields in 249Cf(nth,f)

    Science.gov (United States)

    Tsekhanovich, I.; Büyükmumcu, Z.; Davi, M.; Denschlag, H. O.; Gönnenwein, F.; Boulyga, S. F.

    2003-03-01

    An experiment measuring ternary particle yields in 249Cf(nth,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37Si and 37S; their possible origin is discussed.

  19. Ternary particle yields in 249Cf(nth,f)

    International Nuclear Information System (INIS)

    Tsekhanovich, I.; Bueyuekmumcu, Z.; Davi, M.; Denschlag, H.O.; Goennenwein, F.; Boulyga, S.F.

    2003-01-01

    An experiment measuring ternary particle yields in 249 Cf(n th ,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30 Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37 Si and 37 S; their possible origin is discussed

  20. Laser spectroscopy and beta-NMR measurements of short-lived Mg isotopes

    CERN Document Server

    Kowalska, M

    2005-01-01

    The feasibility of studying the neutron-rich 29Mg, 31Mg and 33Mg isotopes has been demonstrated with the laser and beta-NMR spectroscopy setup at ISOLDE/CERN. The values of the magnetic moment and the nuclear spin of 31Mg are reported and reveal an intruder ground state. This proves the weakening of N=20 shell gap and places this nucleus inside the so called "island of inversion". The experimental setup and technique, as well as the results, are presented.

  1. Systematics in delayed neutron yields

    Energy Technology Data Exchange (ETDEWEB)

    Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan). Atomic Energy Research Inst.

    1998-03-01

    An attempt was made to reproduce the systematic trend observed in the delayed neutron yields for actinides on the basis of the five-Gaussian representation of the fission yield together with available data sets for delayed neutron emission probability. It was found that systematic decrease in DNY for heavier actinides is mainly due to decrease of fission yields of precursors in the lighter side of the light fragment region. (author)

  2. VARIABILITY OF YIELD AND YIELD COMPONENTS IN “EGUSI ...

    African Journals Online (AJOL)

    journal

    Estimate of expected genetic advance in seed yield plant-1 ranged between. 25.90-48.40%. ..... values in fruit and seed yield characters have been reported in culinary melon, ... and Khund, A. 2004. Extent of heterosis and heritability in some.

  3. Response of Yield and Yield Components of Tef [Eragrostis Tef ...

    African Journals Online (AJOL)

    The partial budget analysis also indicates that applications of 46 kg. N ha-1 and 10 kg P ha-1 are ..... (1994) indicated that where the grain yield response is negative, yield reduction is primarily caused by a .... An Economic Training. Manual.

  4. On yield gaps and yield gains in intercropping

    NARCIS (Netherlands)

    Gou, Fang; Yin, Wen; Hong, Yu; Werf, van der Wopke; Chai, Qiang; Heerink, Nico; Ittersum, van Martin K.

    2017-01-01

    Wheat-maize relay intercropping has been widely used by farmers in northwest China, and based on field experiments agronomists report it has a higher productivity than sole crops. However, the yields from farmers’ fields have not been investigated yet. Yield gap analysis provides a framework to

  5. 7755 EFFECT OF NPK FERTILIZER ON FRUIT YIELD AND YIELD ...

    African Journals Online (AJOL)

    Win7Ent

    2013-06-03

    Jun 3, 2013 ... peasant farmers in Nigeria. With the increased ... did not significantly (p=0.05) increase the fruit yield nor the seed yield. Key words: NPK fertilizer, Fruit ..... SAS (Statistical Analysis System) Version 9.1. SAS Institute Inc., Cary, ...

  6. SLIFER measurement for explosive yield

    International Nuclear Information System (INIS)

    Bass, R.C.; Benjamin, B.C.; Miller, H.M.; Breding, D.R.

    1976-04-01

    This report describes the shorted location indicator by frequency of electrical resonance (SLIFER) system used at Sandia Laboratories for determination of explosive yield of under ground nuclear tests

  7. Optimization of decolorization process in agar production from Gracilaria lemaneiformis and evaluation of antioxidant activities of the extract rich in natural pigments.

    Science.gov (United States)

    Yuan, Shengliang; Duan, Zhihong; Lu, Yingnian; Ma, Xiaoli; Wang, Sheng

    2018-01-01

    Gracilaria lemaneiformis is mainly used as a raw material source for agar industry, and its extract is rich in natural pigments with antioxidant activities. In this study, a solvent reflux extraction method for decolorization of G. lemaneiformis has been developed in agar production. The extraction conditions were optimized as follows: solvent-to-material ratio, 50:1; ethanol concentration, 70%; number of extractions, 3; extraction time, 0.5 h, under which the total antioxidant yield of the extract reached 2.89 ± 0.88 mg/g dried seaweeds. Their IC 50 values of DPPH radical scavenging activity, hydroxyl radical scavenging activity and superoxide anion scavenging activity were 21.91 ± 1.8 mg/L, 40.59 ± 1.5 mg/L and 160.87 ± 2.8 mg/L, respectively. Further isolation and spectroscopic analysis of natural pigments suggested the strong antioxidant capacities were attributed to chlorophyll derivatives. The results indicate that the decolorization process was able to improve the agar quality, and the extract containing lots of natural pigments had antioxidant activities which may be used in functional food and cosmetics.

  8. DILEPTON YIELD FROM THE DECAY OF EXCITED SI-28 STATES

    NARCIS (Netherlands)

    BACELAR, JC; BUDA, A; BALANDA, A; KRASZNAHORKAY, A; VANDERPLOEG, H; SUJKOWSKI, Z; VANDERWOUDE, A

    1994-01-01

    The first dilepton yield measurements from excited nuclear states obtained with a new Positron-Electron Pair Spectroscopic Instrument (PEPSI) are reported. Nuclear states in Si-28, with an initial excitation energy E* = 50 MeV, were populated via the isospin T = 0 reaction He-4 + Mg-24 and the

  9. Corrosion inhibition of powder metallurgy Mg by fluoride treatments.

    Science.gov (United States)

    Pereda, M D; Alonso, C; Burgos-Asperilla, L; del Valle, J A; Ruano, O A; Perez, P; Fernández Lorenzo de Mele, M A

    2010-05-01

    Pure Mg has been proposed as a potential degradable biomaterial to avoid both the disadvantages of non-degradable internal fixation implants and the use of alloying elements that may be toxic. However, it shows excessively high corrosion rate and insufficient yield strength. The effects of reinforcing Mg by a powder metallurgy (PM) route and the application of biocompatible corrosion inhibitors (immersion in 0.1 and 1M KF solution treatments, 0.1M FST and 1M FST, respectively) were analyzed in order to improve Mg mechanical and corrosion resistance, respectively. Open circuit potential measurements, polarization techniques (PT), scanning electrochemical microscopy (SECM) and electrochemical impedance spectroscopy (EIS) were performed to evaluate its corrosion behavior. SECM showed that the local current of attacked areas decreased during the F(-) treatments. The corrosion inhibitory action of 0.1M FST and 1M FST in phosphate buffered solution was assessed by PT and EIS. Under the experimental conditions assayed, 0.1M FST revealed better performance. X-ray photoelectron spectroscopy, energy dispersive X-ray and X-ray diffraction analyses of Mg(PM) with 0.1M FST showed the presence of KMgF(3) crystals on the surface while a MgF(2) film was detected for 1M FST. After fluoride inhibition treatments, promising results were observed for Mg(PM) as degradable metallic biomaterial due to its higher yield strength and lower initial corrosion rate than untreated Mg, as well as a progressive loss of the protective characteristics of the F(-)-containing film which ensures the gradual degradation process. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  10. Economics and yields of energy plantations: Status and potential

    International Nuclear Information System (INIS)

    Kenney, W.A.; Gambles, R.L.; Zsuffa, L.

    1992-01-01

    A study was carried out to: determine the factors affecting the cost of energy conversion feedstocks in short rotation intensive culture plantations of trees; determine the factors influencing biomass yield; identify interrelationships between the previous two objectives; present estimates of potential biomass yields and associated economics; and to identify gaps in the knowledge of the economics and yields of biomass production and their interrelationships. Reported costs for most aspects had a wide range. Currently, yields of 10-15 dry Mg/hectare/y are readily achievable. Using the cost and yield data, and assuming a biomass price of $40/dry Mg, a series of cash flow analyses were performed. For the low cost inputs, all scenarios were marginally profitable. For the high cost inputs, none of the scenarios were profitable. A current scenario, using figures for contract farming, was not profitable, however this system would break even with a yield of 23.3 dry Mg/hectare/y, within the range of some production clones. A future scenario using farm labour with increased productivity, product values, and machinery efficiencies yielded a profit-making situation. The addition of incentives increased profitability. There is great potential for the production of woody biomass in Canada as a feedstock for energy and other products. Continued and more intensive breeding and selection to develop high yielding stress tolerant clones, cost efficient harvesting systems, continued research into optimization of planting density, rotation length and cultural techniques, and characterization of promising clones with respect to nutrient-use efficiency, site requirements and pest/disease resistance are important areas for further work. 81 refs., 3 figs., 13 tabs

  11. Sulphate removal from sodium sulphate-rich brine and recovery of barium as a barium salt mixture.

    Science.gov (United States)

    Vadapalli, Viswanath R K; Zvimba, John N; Mulopo, Jean; Motaung, Solly

    2013-01-01

    Sulphate removal from sodium sulphate-rich brine using barium hydroxide and recovery of the barium salts has been investigated. The sodium sulphate-rich brine treated with different dosages of barium hydroxide to precipitate barium sulphate showed sulphate removal from 13.5 g/L to less than 400 mg/L over 60 min using a barium to sulphate molar ratio of 1.1. The thermal conversion of precipitated barium sulphate to barium sulphide achieved a conversion yield of 85% using coal as both a reducing agent and an energy source. The recovery of a pure mixture of barium salts from barium sulphide, which involved dissolution of barium sulphide and reaction with ammonium hydroxide resulted in recovery of a mixture of barium carbonate (62%) and barium hydroxide (38%), which is a critical input raw material for barium salts based acid mine drainage (AMD) desalination technologies. Under alkaline conditions of this barium salt mixture recovery process, ammonia gas is given off, while hydrogen sulfide is retained in solution as bisulfide species, and this provides basis for ammonium hydroxide separation and recovery for reuse, with hydrogen sulfide also recoverable for further industrial applications such as sulfur production by subsequent stripping.

  12. Electronic conductivity of solid and liquid (Mg, Fe)O computed from first principles

    Science.gov (United States)

    Holmström, E.; Stixrude, L.; Scipioni, R.; Foster, A. S.

    2018-05-01

    Ferropericlase (Mg, Fe)O is an abundant mineral of Earth's lower mantle and the liquid phase of the material was an important component of the early magma ocean. Using quantum-mechanical, finite-temperature density-functional theory calculations, we compute the electronic component of the electrical and thermal conductivity of (Mg0.75, Fe0.25)O crystal and liquid over a wide range of planetary conditions: 0-200 GPa, 2000-4000 K for the crystal, and 0-300 GPa, 4000-10,000 K for the liquid. We find that the crystal and liquid are semi-metallic over the entire range studied: the crystal has an electrical conductivity exceeding 103 S/m, whereas that of the liquid exceeds 104 S/m. Our results on the crystal are in reasonable agreement with experimental measurements of the electrical conductivity of ferropericlase once we account for the dependence of conductivity on iron content. We find that a harzburgite-dominated mantle with ferropericlase in combination with Al-free bridgmanite agrees well with electromagnetic sounding observations, while a pyrolitic mantle with a ferric-iron rich bridgmanite composition yields a lower mantle that is too conductive. The electronic component of thermal conductivity of ferropericlase with XFe = 0.19 is negligible (accounts for the high conductance that has been proposed to explain anomalies in Earth's nutation. The electrical conductivity of liquid ferropericlase exceeds that of liquid silica by more than an order of magnitude at conditions of a putative basal magma ocean, thus strengthening arguments that the basal magma ocean could have produced an ancient dynamo.

  13. Breeding for Grass Seed Yield

    DEFF Research Database (Denmark)

    Boelt, Birte; Studer, Bruno

    2010-01-01

    Seed yield is a trait of major interest for many fodder and amenity grass species and has received increasing attention since seed multiplication is economically relevant for novel grass cultivars to compete in the commercial market. Although seed yield is a complex trait and affected...... by agricultural practices as well as environmental factors, traits related to seed production reveal considerable genetic variation, prerequisite for improvement by direct or indirect selection. This chapter first reports on the biological and physiological basics of the grass reproduction system, then highlights...... important aspects and components affecting the seed yield potential and the agronomic and environmental aspects affecting the utilization and realization of the seed yield potential. Finally, it discusses the potential of plant breeding to sustainably improve total seed yield in fodder and amenity grasses....

  14. Age and origin of fluorapatite-rich dyke from Baranec Mt. (Tatra Mts., Western Carpathians: a key to understanding of the post-orogenic processes and element mobility

    Directory of Open Access Journals (Sweden)

    Gawęda Aleksandra

    2016-10-01

    Full Text Available On the southeastern slope of the Baranec Mount in the Western Tatra Mountains (Slovakia an apatite-rich pegmatite-like segregation was found in the subvertical fault zone cutting metapelitic rocks. Two zones: felsic (F and mafic (M were found, differing in mineral assemblages and consequently in chemistry. Fluorapatite crystals yield a LA-ICP-MS U-Pb age of 328.6 ± 2.4 Ma. A temperature decrease from 634 °C to 454 °C at a pressure around 500 to 400 MPa with oxygen fugacity increasing during crystallization are the possible conditions for formation of the pegmatite-like segregation, while secondary alterations took place in the temperature range of 340 – 320 °C. The Sr-Nd isotope composition of both apatite and whole rock point toward a crustal origin of the dike in question, suggesting partial melting of (P, F, H2O-rich metasedimentary rocks during prolonged decompression of the Tatra Massif. The original partial melt (felsic component was mixed with an external (F, H2O-rich fluid, carrying Fe and Mg fluxed from more mafic metapelites and crystallizing as biotite and epidote in the mafic component of the dyke.

  15. Flexible MgO Barrier Magnetic Tunnel Junctions.

    Science.gov (United States)

    Loong, Li Ming; Lee, Wonho; Qiu, Xuepeng; Yang, Ping; Kawai, Hiroyo; Saeys, Mark; Ahn, Jong-Hyun; Yang, Hyunsoo

    2016-07-01

    Flexible MgO barrier magnetic tunnel junction (MTJ) devices are fabricated using a transfer printing process. The flexible MTJ devices yield significantly enhanced tunneling magnetoresistance of ≈300% and improved abruptness of switching, as residual strain in the MTJ structure is released during the transfer process. This approach could be useful for flexible electronic systems that require high-performance memory components. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Examination of the Mg-Zn phase formation in hot-dip galvanized steel sheet; Untersuchung der Mg-Zn-Phasenbildung in feuerverzinktem Stahlblech

    Energy Technology Data Exchange (ETDEWEB)

    Zywitzki, Olaf; Modes, Thomas; Scheffel, Bert; Metzner, Christoph [Fraunhofer-Institut fuer Elektronenstrahl- und Plasmatechnik, Dresden (Germany)

    2012-07-01

    Zinc-magnesium layers have been produced by a combination of conventional hot-dip galvanizing and PVD magnesium coating. A subsequent short heat treatment causes the diffusion of magnesium into the zinc layer. The influence of the maximum temperature of the heat treatment on the diffusion of magnesium and on the type and distribution of the formed intermetallic Mg-Zn phases has been examined in detail in a temperature range from 300 to 400 C by means of X-ray phase analyses and metallographic cross sections. With increasing temperature a sequential intermetallic Mg-Zn phase formation has been detected. At 300 C, an initial magnesium rich, intermetallic MgZn{sub 2} surface layer is formed, which, at higher temperatures from 335 to 379 C, is progressively transformed into a zinc rich Mg{sub 2}Zn{sub 11} layer by interdiffusion. In this context, the nucleation of the Mg{sub 2}Zn{sub 11} phase takes place on the interface between the MgZn{sub 2} and the Zn phase. Above the peritectic temperature of 381 C, the microstructure is composed of a zinc matrix in which precipitated MgZn{sub 2} is dispersed. (orig.)

  17. Enzymatic digestibility and ethanol fermentability of AFEX-treated starch-rich lignocellulosics such as corn silage and whole corn plant

    Directory of Open Access Journals (Sweden)

    Thelen Kurt D

    2010-06-01

    Full Text Available Abstract Background Corn grain is an important renewable source for bioethanol production in the USA. Corn ethanol is currently produced by steam liquefaction of starch-rich grains followed by enzymatic saccharification and fermentation. Corn stover (the non-grain parts of the plant is a potential feedstock to produce cellulosic ethanol in second-generation biorefineries. At present, corn grain is harvested by removing the grain from the living plant while leaving the stover behind on the field. Alternatively, whole corn plants can be harvested to cohydrolyze both starch and cellulose after a suitable thermochemical pretreatment to produce fermentable monomeric sugars. In this study, we used physiologically immature corn silage (CS and matured whole corn plants (WCP as feedstocks to produce ethanol using ammonia fiber expansion (AFEX pretreatment followed by enzymatic hydrolysis (at low enzyme loadings and cofermentation (for both glucose and xylose using a cellulase-amylase-based cocktail and a recombinant Saccharomyces cerevisiae 424A (LNH-ST strain, respectively. The effect on hydrolysis yields of AFEX pretreatment conditions and a starch/cellulose-degrading enzyme addition sequence for both substrates was also studied. Results AFEX-pretreated starch-rich substrates (for example, corn grain, soluble starch had a 1.5-3-fold higher enzymatic hydrolysis yield compared with the untreated substrates. Sequential addition of cellulases after hydrolysis of starch within WCP resulted in 15-20% higher hydrolysis yield compared with simultaneous addition of hydrolytic enzymes. AFEX-pretreated CS gave 70% glucan conversion after 72 h of hydrolysis for 6% glucan loading (at 8 mg total enzyme loading per gram glucan. Microbial inoculation of CS before ensilation yielded a 10-15% lower glucose hydrolysis yield for the pretreated substrate, due to loss in starch content. Ethanol fermentation of AFEX-treated (at 6% w/w glucan loading CS hydrolyzate (resulting

  18. Enzymatic digestibility and ethanol fermentability of AFEX-treated starch-rich lignocellulosics such as corn silage and whole corn plant

    Science.gov (United States)

    2010-01-01

    Background Corn grain is an important renewable source for bioethanol production in the USA. Corn ethanol is currently produced by steam liquefaction of starch-rich grains followed by enzymatic saccharification and fermentation. Corn stover (the non-grain parts of the plant) is a potential feedstock to produce cellulosic ethanol in second-generation biorefineries. At present, corn grain is harvested by removing the grain from the living plant while leaving the stover behind on the field. Alternatively, whole corn plants can be harvested to cohydrolyze both starch and cellulose after a suitable thermochemical pretreatment to produce fermentable monomeric sugars. In this study, we used physiologically immature corn silage (CS) and matured whole corn plants (WCP) as feedstocks to produce ethanol using ammonia fiber expansion (AFEX) pretreatment followed by enzymatic hydrolysis (at low enzyme loadings) and cofermentation (for both glucose and xylose) using a cellulase-amylase-based cocktail and a recombinant Saccharomyces cerevisiae 424A (LNH-ST) strain, respectively. The effect on hydrolysis yields of AFEX pretreatment conditions and a starch/cellulose-degrading enzyme addition sequence for both substrates was also studied. Results AFEX-pretreated starch-rich substrates (for example, corn grain, soluble starch) had a 1.5-3-fold higher enzymatic hydrolysis yield compared with the untreated substrates. Sequential addition of cellulases after hydrolysis of starch within WCP resulted in 15-20% higher hydrolysis yield compared with simultaneous addition of hydrolytic enzymes. AFEX-pretreated CS gave 70% glucan conversion after 72 h of hydrolysis for 6% glucan loading (at 8 mg total enzyme loading per gram glucan). Microbial inoculation of CS before ensilation yielded a 10-15% lower glucose hydrolysis yield for the pretreated substrate, due to loss in starch content. Ethanol fermentation of AFEX-treated (at 6% w/w glucan loading) CS hydrolyzate (resulting in 28 g/L ethanol

  19. Hydrogen incorporation in high hole density GaN:Mg

    Science.gov (United States)

    Zvanut, M. E.; Uprety, Y.; Dashdorj, J.; Moseley, M.; Doolittle, W. Alan

    2011-03-01

    We investigate hydrogen passivation in heavily doped p-type GaN using electron paramagnetic resonance (EPR) spectroscopy. Samples include both conventionally grown GaN (1019 cm-3 Mg, 1017 cm-3 holes) and films grown by metal modulation epitaxy (MME), which yielded higher Mg (1- 4 x 1020 cm-3) and hole (1- 40 x 1018 cm-3) densities than found in conventionally grown GaN. The Mg acceptor signal is monitored throughout 30 minute annealing steps in N2 :H2 (92%:7%)) and subsequently pure N2 . N2 :H2 heat treatments of the lower hole density films begin to reduce the Mg EPR intensity at 750 o C, but quench the signal in high hole density films at 600 o C. Revival of the signal by subsequent N2 annealing occurs at 800 o C for the low hole density material and 600 o C in MME GaN. The present work highlights chemical differences between heavily Mg doped and lower doped films; however, it is unclear whether the difference is due to changes in hydrogen-Mg complex formation or hydrogen diffusion. The work at UAB is supported by the NSF.

  20. In vitro degradation of pure Mg in response to glucose

    Science.gov (United States)

    Zeng, Rong-Chang; Li, Xiao-Ting; Li, Shuo-Qi; Zhang, Fen; Han, En-Hou

    2015-08-01

    Magnesium and its alloys are promising biodegradable biomaterials but are still challenging to be used in person with high levels of blood glucose or diabetes. To date, the influence of glucose on magnesium degradation has not yet been elucidated, this issue requires more attention. Herein, we present pure Mg exhibiting different corrosion responses to saline and Hank’s solutions with different glucose contents, and the degradation mechanism of pure Mg in the saline solution with glucose in comparison with mannitol as a control. On one hand, the corrosion rate of pure Mg increases with the glucose concentration in saline solutions. Glucose rapidly transforms into gluconic acid, which attacks the oxides of the metal and decreases the pH of the solution; it also promotes the absorption of chloride ions on the Mg surface and consequently accelerates corrosion. On the other hand, better corrosion resistance is obtained with increasing glucose content in Hank’s solution due to the fact that glucose coordinates Ca2+ ions in Hank’s solution and thus improves the formation of Ca-P compounds on the pure Mg surface. This finding will open up new avenues for research on the biodegradation of bio-Mg materials in general, which could yield many new and interesting results.

  1. Yield potential and fruit quality of scallop squash (Cucurbita pepo L. var. patissonina Greb. f. radiata Nois. cultivars grown for processing

    Directory of Open Access Journals (Sweden)

    Eugeniusz Kołota

    2015-10-01

    Full Text Available Scallop squash fruits may be harvested at different stages of development. Small size fruits, intended both for the fresh market and the food industry, have the highest biological value. This study was conducted to determine the yield potential of scallop squash cultivars (‘Polo F1’, ‘Disco’, ‘Gagat’, ‘Okra’, ‘Sunny Delight F1’ grown on mulched (black polyethylene foil or black agrotextile or unmulched soil, and harvested when fruits reached a diameter of 3–6 cm. Based on 3-year average data, the highest marketable and early yield was produced by ‘Sunny Delight F1’. This cultivar is also appreciated by consumers for its yellow colored skin of fruits. Another advantage of this cultivar was its high nutritional value expressed by the highest content of dry matter, vitamin C, polyphenols and minerals (K, P, Ca, Mg, with limited tendency to nitrate accumulation. Among the other cultivars tested, ‘Okra’ showed high yield potential, ‘Gagat’ was a rich source of carotenoids, and ‘Disco’ – polyphenols. Black polyethylene foil and black agrotextile appeared to be equally effective mulching materials. The benefit from the application of mulch was a significant increase in yield without any change in the chemical composition of the fruit.

  2. Nitrogen rate and plant population effects on yield and yield ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-12-17

    Gan et al., 2003). Nitrogen increases yield by influencing a variety of agronomic and quality parameters. In general, there was an increase in plant height and dry matter accumulation per plant in soybean (Manral and Saxena, ...

  3. Nitrogen rate and plant population effects on yield and yield ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-12-17

    Dec 17, 2008 ... density and nitrogen rate increased plant height, lowest pod height, harvest index and seed yield. ... since some combine harvester heads are unable to pick ..... as effected by population density and plant distribution.

  4. Mg isotopes and the disappearance of magic N=20 - Laser and beta-NMR studies

    CERN Document Server

    Kowalska, M

    2006-01-01

    Collinear laser spectroscopy and beta-NMR spectroscopy with optical pumping were applied at ISOLDE/CERN to measure for the first time the magnetic moments of neutron-rich 27Mg, 29Mg, 31Mg and 33Mg, along with the spins of the two latter. The magnetic moment of 27Mg was derived from its hyperfine structure detected in UV fluorescent light, whereas the nuclear magnetic resonance observed in beta-decay asymmetry from a polarised ensemble of nuclei gave the magnetic moment of 29Mg. For 31Mg and 33Mg, the hyperfine structure and nuclear magnetic resonance gave the spin and the magnetic moment. The preliminary results for 27Mg and 29Mg are consistent with a large neutron shell gap at N=20, whereas data on 31Mg show that for this nucleus N=20 is not a magic number, which is also the case for 33Mg, based on preliminary analysis. Thus, the two latter isotopes belong to the island of inversion.

  5. Effects of application boron on yields, yield component and oil ...

    African Journals Online (AJOL)

    The study was conducted to investigate the effects of five boron (B) doses; 0, 2.5, 5.0, 7.5 and 10.0 kg B ha-1 in B-deficient calcareous soils on yield and some yield components of four sunflower genotypes. Genotypes have shown variations with respect to their responses to B applications. AS-615 and Coban had the ...

  6. Predicting trends of invasive plants richness using local socio-economic data: An application in North Portugal

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Mario, E-mail: mgsantoss@gmail.com [Laboratory of Applied Ecology, CITAB-Centre for the Research and Technology of Agro-Environment and Biological Sciences, University of Tras-os-Montes e Alto Douro, 5000-911 Vila Real (Portugal); Freitas, Raul, E-mail: raulfreitas@portugalmail.com [Herbarium, UTAD Botanical Garden, CITAB-Centre for the Research and Technology of Agro-Environment and Biological Sciences, University of Tras-os-Montes e Alto Douro, 5000-911 Vila Real (Portugal); Crespi, Antonio L., E-mail: aluis.crespi@gmail.com [Herbarium, UTAD Botanical Garden, CITAB-Centre for the Research and Technology of Agro-Environment and Biological Sciences, University of Tras-os-Montes e Alto Douro, 5000-911 Vila Real (Portugal); Hughes, Samantha Jane, E-mail: shughes@utad.pt [Department of Forest and Landscape, CITAB-Centre for the Research and Technology of Agro-Environment and Biological Sciences, University of Tras-os-Montes e Alto Douro, 5000-911 Vila Real (Portugal); Cabral, Joao Alexandre, E-mail: jcabral@utad.pt [Laboratory of Applied Ecology, CITAB-Centre for the Research and Technology of Agro-Environment and Biological Sciences, University of Tras-os-Montes e Alto Douro, 5000-911 Vila Real (Portugal)

    2011-10-15

    This study assesses the potential of an integrated methodology for predicting local trends in invasive exotic plant species (invasive richness) using indirect, regional information on human disturbance. The distribution of invasive plants was assessed in North Portugal using herbarium collections and local environmental, geophysical and socio-economic characteristics. Invasive richness response to anthropogenic disturbance was predicted using a dynamic model based on a sequential modeling process (stochastic dynamic methodology-StDM). Derived scenarios showed that invasive richness trends were clearly associated with ongoing socio-economic change. Simulations including scenarios of growing urbanization showed an increase in invasive richness while simulations in municipalities with decreasing populations showed stable or decreasing levels of invasive richness. The model simulations demonstrate the interest and feasibility of using this methodology in disturbance ecology. - Highlights: {yields} Socio-economic data indicate human induced disturbances. {yields} Socio-economic development increase disturbance in ecosystems. {yields} Disturbance promotes opportunities for invasive plants.{yields} Increased opportunities promote richness of invasive plants.{yields} Increase in richness of invasive plants change natural ecosystems.

  7. Decomposing global crop yield variability

    Science.gov (United States)

    Ben-Ari, Tamara; Makowski, David

    2014-11-01

    Recent food crises have highlighted the need to better understand the between-year variability of agricultural production. Although increasing future production seems necessary, the globalization of commodity markets suggests that the food system would also benefit from enhanced supplies stability through a reduction in the year-to-year variability. Here, we develop an analytical expression decomposing global crop yield interannual variability into three informative components that quantify how evenly are croplands distributed in the world, the proportion of cultivated areas allocated to regions of above or below average variability and the covariation between yields in distinct world regions. This decomposition is used to identify drivers of interannual yield variations for four major crops (i.e., maize, rice, soybean and wheat) over the period 1961-2012. We show that maize production is fairly spread but marked by one prominent region with high levels of crop yield interannual variability (which encompasses the North American corn belt in the USA, and Canada). In contrast, global rice yields have a small variability because, although spatially concentrated, much of the production is located in regions of below-average variability (i.e., South, Eastern and South Eastern Asia). Because of these contrasted land use allocations, an even cultivated land distribution across regions would reduce global maize yield variance, but increase the variance of global yield rice. Intermediate results are obtained for soybean and wheat for which croplands are mainly located in regions with close-to-average variability. At the scale of large world regions, we find that covariances of regional yields have a negligible contribution to global yield variance. The proposed decomposition could be applied at any spatial and time scales, including the yearly time step. By addressing global crop production stability (or lack thereof) our results contribute to the understanding of a key

  8. Growth and scintillation properties of BaMgF4

    International Nuclear Information System (INIS)

    Yanagida, Takayuki; Kawaguchi, Noriaki; Fujimoto, Yutaka; Sugiyama, Makoto; Furuya, Yuki; Kamada, Kei; Yokota, Yuui; Yoshikawa, Akira; Chani, Valery

    2010-01-01

    By using the micro-pulling down (μ-PD) method, the barium magnesium fluoride (BaMgF 4 ) single crystalline scintillator was produced. The crystal was cut and mirror polished to the physical dimensions of 1x2x10 mm 3 for examination of scintillation properties. BaMgF 4 demonstrated ∼70% transmittance in wavelength range above 170 nm, and strong emission peaking around 205 nm was observed under X-ray excitation. The absolute light yield of BaMgF 4 was 1300±100 ph/MeV, and the decay time profile showed two components as 0.57±0.01 (70%) and 2.2±0.31 (30%) ns at room temperature.

  9. Early Cretaceous Na-rich granitoids and their enclaves in the Tengchong Block, SW China: Magmatism in relation to subduction of the Bangong-Nujiang Tethys ocean

    Science.gov (United States)

    Zhu, Ren-Zhi; Lai, Shao-Cong; Santosh, M.; Qin, Jiang-Feng; Zhao, Shao-Wei

    2017-08-01

    The Na-rich intermediate-to-felsic granitic rocks provide insights into the generation of magmas in subduction zones. This paper presents zircon LA-ICP-MS U-Pb ages as well as whole-rock geochemical, mineral chemical, and in situ zircon Hf isotopic data on Na-rich granitic rocks from the Tengchong Block, SW China. The granodiorites and associated mafic magmatic enclaves (MMEs) from the Menglian batholith yield zircon U-Pb ages of 116.1 ± 0.8 to 117.8 ± 0.6 Ma and 117.7 ± 0.7 Ma, respectively. Both host granodiorites and enclaves show calc-alkaline and sodium-rich nature, enrichment in large-ion lithophile elements (LILEs), and variable depletion in zircon Hf isotopic compositions. Euhedral amphiboles in both granodiorites and associated enclaves are magnesian-hornblende with high Mg and Ca and contain euhedral plagioclase inclusions of labradorite to andesine (An36-57) composition. The granodiorite was most likely derived through the mixing of partial melts derived from juvenile basaltic lower crust and a minor evolved component of ancient crustal sources. The quartz monzodiorite-granodiorites and associated MMEs from the Xiaotang-Mangdong batholith yield zircon U-Pb ages of 120.3 ± 1.3 to 122.6 ± 0.8 Ma and 120.7 ± 1.5 Ma. These rocks are also sodium-rich and show calc-alkaline trend with negative zircon Hf isotopic compositions (- 5.55 to + 0.58). The MMEs in the host intrusions are monzogabbro with variable and depleted zircon Hf isotopic compositions. The amphiboles in the both host intrusions and the enclaves show Al-rich ferro-tschermakite composition. We infer that the quartz monzodiorite-granodiorites were derived from magmas generated by the melting of ancient basaltic rocks in the lower arc crust induced by the underplating of mantle-derived mafic magmas. The formation of the different types of Na-rich granitic rocks is correlated to the subduction of Bangong-Nujiang Tethyan ocean. A comparison with magmatism in the northern magmatic belt suggests

  10. Stability of rapidly quenched and hydrogenated Mg-Ni-Y and Mg-Cu-Y alloys in extreme alkaline medium

    International Nuclear Information System (INIS)

    Gebert, A.; Khorkounov, B.; Wolff, U.; Mickel, Ch.; Uhlemann, M.; Schultz, L.

    2006-01-01

    Amorphous-nanocrystalline Mg 50 Ni 30 Y 20 and Mg 63 Ni 30 Y 7 and amorphous Mg 65 Cu 25 Y 10 alloys were produced by melt-spinning and characterized regarding their microstructure and thermal behaviour using XRD, TEM and DSC. Their electrochemical behaviour in the as-quenched state and after hydrogen charging at -25 mA/cm 2 for up to 20 h was studied in electrolytes with pH 5-7 and 13, but mainly in a battery electrolyte: 6 M KOH with pH 14.8 by means of anodic and cathodic polarization measurements. In the as-quenched state, the highest alloys stability was observed at pH 13. At pH 14.8, gradual oxidation and dissolution of copper or nickel governs the anodic behaviour before a passive state is attained. The dissolution of nickel is much more inhibited than that of copper due to its lower tendency to form soluble oxidized ions and to a stabilizing effect of higher fractions of yttrium in the alloy on the passivation. By galvanostatic charging, the Mg 65 Cu 25 Y 10 alloy shows the highest hydrogen absorption capacity followed by Mg 50 Ni 30 Y 20 and Mg 63 Ni 30 Y 7 . During the charging process, the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel- or copper-rich species, causing preferential oxidation and dissolution during subsequent exposure under free corrosion and anodic conditions. Mg-Ni-Y alloys demonstrate a higher stability during this treatment in extreme alkaline medium. The reasons for this and consequences regarding the use as electrode materials are discussed in detail

  11. Elastic and Plastic Behavior of an Ultrafine-Grained Mg Reinforced with BN Nanoparticles

    Science.gov (United States)

    Trojanová, Zuzanka; Dash, Khushbu; Máthis, Kristián; Lukáč, Pavel; Kasakewitsch, Alla

    2018-04-01

    Pure microcrystalline magnesium (µMg) was reinforced with hexagonal boron nitride (hBN) nanoparticles and was fabricated by powder metallurgy process followed by hot extrusion. For comparison pure magnesium powder was consolidated by hot extrusion too. Both materials exhibited a significant fiber texture. Mg-hBN nanocomposites (nc) and pure Mg specimens were deformed between room temperature and 300 °C under tension and compression mode. The yield strength and ultimate tensile and compression strength as well as characteristic stresses were evaluated and reported. The tensile and compressive strengths of Mg-hBN nc are quiet superior in values compared to monolithic counterpart as well as Mg alloys. The compressive yield strength of µMg was recorded as 90 MPa, whereas the Mg-hBN nancomposite shows 125 MPa at 200 °C. The tensile yield strength of µMg was computed as 67 MPa which is quite lower as compared to Mg-hBN nanocomposite's value which was recorded as 157 MPa at 200 °C. Under tensile stress the true stress-strain curves are flat in nature, whereas the stress-strain curves observed in compression at temperatures up to 100 °C exhibited small local maxima at the onset of deformation followed by a significant work hardening.

  12. Dilepton as a signature for the baryon-rich quark-gluon matter

    International Nuclear Information System (INIS)

    Zejun He; Jiaju Zhang

    1995-01-01

    From the full stopping scenario, we study dilepton production in a baryon rich quark-gluon fireball on the basis of a relativistic hydrodynamic model, and find that with increasing initial baryon density a characteristic valley and a subsequent peak, which more uniquely signal the formation of the baryon-rich quark-gluon matter, appear in the total dilepton yield. Such characteristics can be tested in future experiments at CERN and Brookhaven. (author). Letter-to-the-editor

  13. Structural elucidation, molecular representation and solvent interactions of vitrinite-rich and inertinite-rich South African coals

    Science.gov (United States)

    van Niekerk, Daniel

    the kinetic parameters and it was found that the swelling was governed by relaxation of the coal structure (super-Case II swelling). X-ray computed tomography was conducted confirming anisotropic swelling. The petrographic transitions (maceral-group composition and reflectance) with solvent swelling and extraction were quantified. No changes in the maceral compositions were found, but changes in some coal particles were observed. Random reflectance analysis showed that, for both vitrinite and inertinite, there is a decrease in reflectance values with solvent treatment. Vitrinite reflectograms showed a shift from the dominant reflecting V-types to lower V-types. The inertinite reflectograms exhibited an increase in number of I-types (broadening of reflectrograms). Molecular simulation and visualization approaches to solvent swelling and extraction were performed on the proposed molecular models of vitrinite-rich and inertinite-rich coals. A theoretical extraction yield was determined using solubility parameters and showed agreement with experimental extraction yield trends. Statistical Associating Fluid Theory (SAFT) modeling was explored to test whether this method could predict swelling extent. The predicted swelling trends of SAFT were comparable to that of the experimental swelling results. SAFT was found to be a promising tool for solvent-coal interaction predictions. Partially solvent swollen structures were constructed by the addition of solvent molecules to the original coal molecules using a amorphous building approach. This method showed that coal-coal non-bonding interaction changed with the introduction of solvent. A disruption in the van der Waals interaction energies and a change in hydrogen bond distributions were observed in the swollen coal models and quantified. It was concluded that small changes in coal structure translates to significant changes in solvent interaction behavior. These changes were successfully visualized and simulated using

  14. Mechanical and corrosion properties of binary Mg-Dy alloys for medical applications

    Energy Technology Data Exchange (ETDEWEB)

    Yang Lei, E-mail: lei.yang@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany); Yuanding, Huang; Qiuming, Peng; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany)

    2011-12-15

    Microstructure, mechanical and corrosion properties of binary magnesium-dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg-10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg-Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

  15. Discharge characteristics of plasma display panels with Si-doped MgO protective layers

    Energy Technology Data Exchange (ETDEWEB)

    Ram, Sanjay K., E-mail: sanjayk.ram@gmail.co [Laboratoire de Physique des Interfaces et des Couches Minces (UMR 7647 du CNRS), Ecole Polytechnique, 91128 Palaiseau Cedex (France); Department of Physics, Indian Institute of Technology Kanpur, Kanpur-208016 (India); Barik, U K [Samtel Color Limited, Ghaziabad-201009 (India); Sarkar, Surajit; Biswas, Paramananda [Department of Physics, Indian Institute of Technology Kanpur, Kanpur-208016 (India); Singh, Vandana [Laboratoire de Physique des Interfaces et des Couches Minces (UMR 7647 du CNRS), Ecole Polytechnique, 91128 Palaiseau Cedex (France); Dwivedi, H K [Samtel Color Limited, Ghaziabad-201009 (India); Kumar, Satyendra [Department of Physics, Indian Institute of Technology Kanpur, Kanpur-208016 (India)

    2009-10-01

    We report on our study of the influence of varying concentrations of Si doping on the secondary electron emission (SEE) yield of MgO thin films prepared by electron beam evaporation technique. The series of Si-doped MgO films were microstructurally characterized with various tools like X-ray diffraction, scanning electron microscopy and atomic force microscopy. The optimization of the concentration of Si doping is seen to enhance the SEE yield. We discuss the correlation of SEE yield in the context of different deposition and measurement conditions and crystalline orientation.

  16. Investigating equality: The poverty and riches indices

    International Nuclear Information System (INIS)

    Eliazar, Iddo

    2016-01-01

    As noise is omnipresent, real-world quantities measured by scientists and engineers are commonly obtained in the form of statistical distributions. In turn, perhaps the most compact representation of a given statistical distribution is via the mean-variance approach: the mean manifesting the distribution’s ‘typical’ value, and the variance manifesting the magnitude of the distribution’s fluctuations about its mean. The mean-variance approach is based on an underlying Euclidean-geometry perspective. So very often real-world quantities of interest are non-negative sizes, and their measurements yield statistical size distributions. In this paper, and in the context of size distributions, we present an alternative to the Euclidean-based mean-variance approach: a mean-equality approach that is based on an underlying socioeconomic perspective. We establish two equality indices that score, on a unit-interval scale, the intrinsic ‘egalitarianism’ of size distributions: (i) the poverty equality index which is particularly sensitive to the existence of very small “poor” sizes; (ii) the riches equality index which is particularly sensitive to the existence of very large “rich” sizes. These equality indices, their properties, their computation, their application, and their connections to the mean-variance approach – are explored and described comprehensively.

  17. Fission yield measurements at IGISOL

    Science.gov (United States)

    Lantz, M.; Al-Adili, A.; Gorelov, D.; Jokinen, A.; Kolhinen, V. S.; Mattera, A.; Moore, I.; Penttilä, H.; Pomp, S.; Prokofiev, A. V.; Rakopoulos, V.; Rinta-Antila, S.; Simutkin, V.; Solders, A.

    2016-06-01

    The fission product yields are an important characteristic of the fission process. In fundamental physics, knowledge of the yield distributions is needed to better understand the fission process. For nuclear energy applications good knowledge of neutroninduced fission-product yields is important for the safe and efficient operation of nuclear power plants. With the Ion Guide Isotope Separator On-Line (IGISOL) technique, products of nuclear reactions are stopped in a buffer gas and then extracted and separated by mass. Thanks to the high resolving power of the JYFLTRAP Penning trap, at University of Jyväskylä, fission products can be isobarically separated, making it possible to measure relative independent fission yields. In some cases it is even possible to resolve isomeric states from the ground state, permitting measurements of isomeric yield ratios. So far the reactions U(p,f) and Th(p,f) have been studied using the IGISOL-JYFLTRAP facility. Recently, a neutron converter target has been developed utilizing the Be(p,xn) reaction. We here present the IGISOL-technique for fission yield measurements and some of the results from the measurements on proton induced fission. We also present the development of the neutron converter target, the characterization of the neutron field and the first tests with neutron-induced fission.

  18. Fission yield measurements at IGISOL

    Directory of Open Access Journals (Sweden)

    Lantz M.

    2016-01-01

    Full Text Available The fission product yields are an important characteristic of the fission process. In fundamental physics, knowledge of the yield distributions is needed to better understand the fission process. For nuclear energy applications good knowledge of neutroninduced fission-product yields is important for the safe and efficient operation of nuclear power plants. With the Ion Guide Isotope Separator On-Line (IGISOL technique, products of nuclear reactions are stopped in a buffer gas and then extracted and separated by mass. Thanks to the high resolving power of the JYFLTRAP Penning trap, at University of Jyväskylä, fission products can be isobarically separated, making it possible to measure relative independent fission yields. In some cases it is even possible to resolve isomeric states from the ground state, permitting measurements of isomeric yield ratios. So far the reactions U(p,f and Th(p,f have been studied using the IGISOL-JYFLTRAP facility. Recently, a neutron converter target has been developed utilizing the Be(p,xn reaction. We here present the IGISOL-technique for fission yield measurements and some of the results from the measurements on proton induced fission. We also present the development of the neutron converter target, the characterization of the neutron field and the first tests with neutron-induced fission.

  19. HTML5 rich media foundation

    CERN Document Server

    David, Matthew

    2010-01-01

    Learn about the new ways in which video and audio can be easily embedded into your HTML5 Web pages. Discover how you can create new Web media content and how JavaScript, CSS, and SVG can be integrated to create a compelling, rich media foundation for your work. HTML 5, is the first major update to the core language of the Web in over a decade The focus of this book is on innovations that most directly effect Web site design and multimedia integration The companion Web site features working demonstrations and tutorial media for hands-on pract

  20. Struvite Precipitation as a Means of Recovering Nutrients and Mitigating Ammonia Toxicity in a Two-Stage Anaerobic Digester Treating Protein-Rich Feedstocks.

    Science.gov (United States)

    Wang, Shunli; Hawkins, Gary L; Kiepper, Brian H; Das, Keshav C

    2016-08-03

    Accumulation of ammonia, measured as total ammonia nitrogen (TAN), a product of protein decomposition in slaughterhouse wastes, inhibits the anaerobic digestion process, reducing digester productivity and leading to failure. Struvite precipitation (SP) is an effective means to remove TAN and enhance the buffering of substrates. Different Mg and P sources were evaluated as reactants in SP in acidogenic digester effluents to reduce its TAN levels. In order to measure impact of TAN removal, a standard biochemical methane potential (BMP) test was conducted to measure methane yield from treatments that had the highest TAN reductions. SP results showed 6 of 9 reagent combinations resulted in greater than 70% TAN removal. The BMP results indicated that SP treatment by adding Mg(OH)₂ and H₃PO₄ resulted in 57.6% nitrogen recovery and 41.7% increase in methane yield relative to the substrate without SP. SP is an effective technology to improve nutrient recovery and methane production from the anaerobic digestion of protein-rich feedstocks.

  1. Struvite Precipitation as a Means of Recovering Nutrients and Mitigating Ammonia Toxicity in a Two-Stage Anaerobic Digester Treating Protein-Rich Feedstocks

    Directory of Open Access Journals (Sweden)

    Shunli Wang

    2016-08-01

    Full Text Available Accumulation of ammonia, measured as total ammonia nitrogen (TAN, a product of protein decomposition in slaughterhouse wastes, inhibits the anaerobic digestion process, reducing digester productivity and leading to failure. Struvite precipitation (SP is an effective means to remove TAN and enhance the buffering of substrates. Different Mg and P sources were evaluated as reactants in SP in acidogenic digester effluents to reduce its TAN levels. In order to measure impact of TAN removal, a standard biochemical methane potential (BMP test was conducted to measure methane yield from treatments that had the highest TAN reductions. SP results showed 6 of 9 reagent combinations resulted in greater than 70% TAN removal. The BMP results indicated that SP treatment by adding Mg(OH2 and H3PO4 resulted in 57.6% nitrogen recovery and 41.7% increase in methane yield relative to the substrate without SP. SP is an effective technology to improve nutrient recovery and methane production from the anaerobic digestion of protein-rich feedstocks.

  2. Conservation and Biodiversity of Rich Fens

    DEFF Research Database (Denmark)

    Andersen, Dagmar Kappel

    2014-01-01

    Rich fen is a habitat type dependent on a constant supply of nutrient poor, calcium rich groundwater. A high, stable groundwater table, relatively high pH combined with nutrient poor conditions support a special and very species rich vegetation including many rare and threatened plant species. In...

  3. Platelet-rich fibrin in the treatment of periodontal bone defects.

    Science.gov (United States)

    Ranganathan, Aravindhan T; Chandran, Chitraa R

    2014-05-01

    Periodontitis is characterized by the formation of true pockets, bone loss and attachment loss. Various techniques have been attempted in the past to truly regenerate the lost periodontal structures, albeit with variable outcome. In this evolution, the technique being tried out widely is the use of platelet rich concentrates, namely platelet-rich fibrin (PRF). In this report, we present a case of surgical treatment of osseous bone defects namely two walled crater and dehiscence treated in posterior teeth with autologously prepared platelet rich fibrin mixed with hydroxy apatite bone graft and PRF in the form of a membrane. Our results showed clinical improvements in all the clinical parameters postoperatively namely the pocket depth reduction and gain in attachment level and hence, PRF can be used alone or in combination with the bone graft to yield successful clinical results in treating periodontal osseous defects. Platelet-rich fibrin is an effective alternative to platelet-rich plasma (PRP) in reconstructing bone defects.

  4. Shotgun Approach to Increasing Enzymatic Saccharification Yields of Ammonia Fiber Expansion Pretreated Cellulosic Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Chundawat, Shishir P. S., E-mail: shishir.chundawat@rutgers.edu [Department of Chemical and Biochemical Engineering, Rutgers-State University of New Jersey, Piscataway, NJ (United States); Uppugundla, Nirmal; Gao, Dahai [Department of Chemical Engineering and Materials Science, Michigan State University, East Lansing, MI (United States); Curran, Paul G. [Center for Statistical Training and Consulting (CSTAT), Michigan State University, East Lansing, MI (United States); Balan, Venkatesh; Dale, Bruce E. [Department of Chemical Engineering and Materials Science, Michigan State University, East Lansing, MI (United States)

    2017-05-10

    Most cellulolytic enzyme blends, either procured from a commercial vendor or isolated from a single cellulolytic microbial secretome, do not efficiently hydrolyze ammonia-pretreated (e.g., ammonia fiber expansion, AFEX) lignocellulosic agricultural crop residues like corn stover to fermentable sugars. Typically reported commercial enzyme loading (30–100 mg protein/g glucan) necessary to achieve >90% total hydrolysis yield (to monosaccharides) for AFEX-treated biomass, within a short saccharification time frame (24–48 h), is economically unviable. Unlike acid-based pretreatments, AFEX retains most of the hemicelluloses in the biomass and therefore requires a more complex suite of enzymes for efficient hydrolysis of cellulose and hemicellulose at industrially relevant high solids loadings. One strategy to reduce enzyme dosage while improving cocktail effectiveness for AFEX-treated biomass has been to use individually purified enzymes to determine optimal enzyme combinations to maximize hydrolysis yields. However, this approach is limited by the selection of heterologous enzymes available or the labor required for isolating low-abundance enzymes directly from the microbial secretomes. Here, we show that directly blending crude cellulolytic and hemicellulolytic enzymes-rich microbial secretomes can maximize specific activity on AFEX-treated biomass without having to isolate individual enzymes. Fourteen commercially available cellulolytic and hemicellulolytic enzymes were procured from leading enzyme companies (Novozymes{sup ®}, Genencor{sup ®}, and Biocatalysts{sup ®}) and were mixed together to generate several hundred unique cocktail combinations. The mixtures were assayed for activity on AFEX-treated corn stover (AFEX-CS) using a previously established high-throughput methodology. The optimal enzyme blend combinations identified from these screening assays were enriched in various low-abundance hemicellulases and accessory enzymes typically absent in most

  5. System tests of the LHCb RICH detectors in a charged particle beam

    CERN Document Server

    Skottowe, Hugh

    2009-01-01

    The RICH detectors of the LHCb experiment will provide efficient particle identification over the momentum range 1-100 GeV=c. Results are presented from a beam test of the LHCb RICH system using final production pixel Hybrid Photon Detectors, the final readout electronics and an adapted version of LHCb RICH reconstruction software. Measurements of the photon yields and Cherenkov angle resolutions for both nitrogen and C4F10 radiators agree well with full simulations. The quality of the data and the results obtained demonstrate that all aspects meet the stringent physics requirements of the experiment are now ready for first data.

  6. FOLIAR NUTRIENT CONTENTS AND FRUIT YIELD IN CUSTARD APPLE PROGENIES

    Directory of Open Access Journals (Sweden)

    Paulo Sérgio Lima e Silva

    2009-01-01

    Full Text Available Foliar nutrient contents are evaluated in several fruit trees with many objectives. Leaf analysis constitutes a way of evaluating the nutritional requirements of crops. Due to the positive impact that fertilizers have on crop yields, researchers frequently try to evaluate the correlations between yield and foliar nutrient contents. This work's objective was to present fruit yields from the 4th to the 6th cropping seasons, evaluate foliar nutrient contents (on the 5th cropping season, and estimate the correlations between these two groups of traits for 20 half-sibling custard apple tree progenies. The progenies were evaluated in a random block design with five replicates and four plants per plot. One hundred leaves were collected from the middle third of the canopy (in height of each of four plants in each plot. The leaves were collected haphazardly, i.e., in a random manner, but without using a drawing mechanism. In the analysis of variance, the nutrient concentrations in the leaves from plants of each plot were represented by the average of four plants in the plot. Fruit yield in the various progenies did not depend on cropping season; progeny A4 was the most productive. No Spearman correlation was found between leaf nutrient concentrations and fruit yield. Increased nutrient concentrations in the leaves were progeny-dependent, i.e., with regard to Na (progenies FE5 and JG1, Ca (progeny A4, Mg (progeny SM7, N (progeny A3, P (progeny M, and K contents (progeny JG3. Spearman's correlation was negative between Na-Mg, Na-Ca, and Mg-P contents, and positive between Mg-Ca and N-K contents.

  7. Influence Of The Neutron Richness On Binary Decays

    Directory of Open Access Journals (Sweden)

    Roy R.

    2010-03-01

    Full Text Available The influence of the neutron richness on binary decays is investigated in 78,82Kr+ 40Ca reactions at 5.5 MeV/A incident energy. Kinetic energy distributions and angular distributions of fragments with atomic number 6 ≤ Z ≤ 28 were measured using the 4π-INDRA array. Global features are compatible with an emission from a long-lived system. The yields around the symmetric splitting are about 30The persistence of strong structural effects is evidenced from elemental cross-sections of the light fragments. The cross-sections for odd-Z fragments are higher for the neutron rich CN while cross-sections for even-Z fragments are higher for the neutron poor CN. Calculations assuming two different potential energy surfaces are presented.

  8. Excitation energy of the lowest 2+ and 3- levels in 32Mg and 146Gd

    International Nuclear Information System (INIS)

    Barranco, M.; Lombard, R.J.

    1978-06-01

    The excitation energy of the lowest 2 + and 3 - levels are calculated for neutron rich Mg-isotopes as well as for N=82 isotones. The calculations are made by assuming quadrupole-quadrupole and octupole-octupole forces. The quasi-particles energies and occupation numbers are taken from the energy density method

  9. Hydrothermal replacement of calcite by Mg-carbonates

    Science.gov (United States)

    Jonas, Laura; Mueller, Thomas; Dohmen, Ralf

    2014-05-01

    The transport of heat and mass through the Earth's crust is coupled to mineral reactions and the exchange of isotopes and elements between different phases. Carbonate minerals are a major constituent of the Earth's crust and play an important role in different physical, chemical and even biological processes. In this experimental study, the element exchange reaction between calcite (CaCO3) and a Mg-rich fluid phase is investigated under hydrothermal conditions. Single crystals of calcite (2x2x2 mm) react with 1 ml of a 1 M MgCl2 solution at 200° C in a Teflon-lined steel autoclave for different times between one day and four weeks. The reaction leads to the formation of a porous reaction front and the pseudomorphic replacement of calcite by dolomite [CaMg(CO3)2] and magnesite (MgCO3). Scanning electron microscopy revealed that the reaction rim consists of small Mg-carbonate rhombs closely attached to each other, suggesting that the replacement reaction takes place by a dissolution-precipitation mechanism. Typically, the observed reaction front can be divided into two different domains. The outer part of the reaction rim, i.e. from the mineral surface in contact to the fluid inwards, consists of magnesite, whereas the inner part of the rim surrounding the unreacted calcite core consists of Ca-rich dolomite. The formation of a porous microstructure that varies in different parts of the reaction rim is a direct result of the large molar volume change induced by the replacement of calcite by magnesite and dolomite. The developing porosity therefore creates fluid pathways that promote the progress of the reaction front towards the unreacted core of the single crystal. Compositional profiles measured perpendicular to the mineral surface across the reactions rims using electron microprobe (EMPA) further revealed a compositional gradient within the reaction rim with regard to the structure-forming elements Mg and Ca. Here, the amount of Mg incorporated in both product

  10. Discovery of the shape coexisting 0+ state in 32Mg

    International Nuclear Information System (INIS)

    Wimmer, Kathrin

    2010-01-01

    The evolution of shell structure in exotic nuclei as a function of proton (Z) and neutron (N) number is currently at the center of many theoretical and experimental investigations. It has been realized that the interaction of the last valence protons and neutrons, in particular the monopole component of the residual interaction between those nucleons, can lead to significant shifts in the single-particle energies, leading to the collapse of classic shell closures and the appearance of new shell gaps. The ''Island of Inversion'' around 32 Mg, which is one of the most studied phenomena in the nuclear chart, is a well known example for such changes in nuclear structure. In this region of neutron-rich nuclei around the magic number N=20 strongly deformed ground states in Ne, Na, and Mg isotopes have been observed. Due to the reduction of the N=20 shell gap quadrupole correlations can enable low-lying deformed 2p-2h intruder states from the fp-shell to compete with spherical normal neutron 0p-0h states of the sd-shell. In this situation the promotion of a neutron pair across the N=20 gap can result in deformed intruder ground states. Consequentially the two competing configurations can lead to the coexistence of spherical and deformed 0 + states in the neutron rich nuclei 30,32 Mg. In this work the shape coexistence in 32 Mg was studied by a two neutron transfer reaction at the REX-ISOLDE facility (CERN). The two neutron transfer reaction with a 30 Mg beam involved for the first time the use of a radioactive tritium target in combination with a radioactive heavy ion beam. Light charged particles emitted from the target were detected and identified by the T-REX particle detector while γ-rays were detected by the MINIBALL Germanium detector array. The shape of the angular distribution of the protons allows to unambiguously determine the angular momentum transfer ΔL of the reaction and thus to identify the 0 + states. The analysis of excitation energies and angular

  11. The role of Mg in the crystallization of monohydrocalcite

    Science.gov (United States)

    Rodriguez-Blanco, Juan Diego; Shaw, Samuel; Bots, Pieter; Roncal-Herrero, Teresa; Benning, Liane G.

    2014-02-01

    Monohydrocalcite is a member of the carbonate family which forms in Mg-rich environments at a wide range of Mg/Ca ratios Mg2+aq/Ca2+aq≥0.17stock solutions. However, its crystallite and particle size are inversely proportional to these parameters. At high supersaturations (SIMHC = 3.89) nanometer-sized single crystals of monohydrocalcite form, while at low values (SIMHC = 2.43) the process leads to low-angle branching spherulites. Many carbonates produced during biomineralization form at similar conditions to most synthetic monohydrocalcites, and thus we hypothesize that some calcite or aragonite deposits found in the geologic record that have formed at high Mg/Ca ratios could be secondary in origin and may have originally formed via a metastable monohydrocalcite intermediate. High-Mg monohydrocalcite (χMgCO3 > 0.06) consists of individual nanometer-sized crystals (500 °C (Fig. 9b). Such high-Mg monohydrocalcites are uncommon in nature, but can be synthesized in the laboratory at high initial supersaturation levels (SI > 3.25). Low-Mg monohydrocalcite (χMgCO3 bonded to Mg, so it fully dehydrates at low temperatures (150-200 °C). They have the same composition as natural monohydrocalcites reported in the literature, and can be synthesized in the laboratory at lower supersaturation levels (SI relationships. Firstly, our on-line experiment shows an increase in nanocrystal sizes during the secondary crystallization of monohydrocalcite, which is coupled with a significant decrease in χMgCO3 (from ˜0.26 to ˜0.065). This corresponds to the transition from high- to low-Mg monohydrocalcite, suggesting that the former would be metastable and rapidly transforming to the latter, possibly triggered by the removal of Mg from aqueous solution. Secondly, Davis et al. (2000) determined that the solubility of Mg-calcite (Ca1-xMgxCO3; x = 0-0.20) varies by approximately half an order of magnitude depending on the Mg content of the solid (Ksp = 10-8.0-10-8.5). A similar

  12. Level structures of neutron-rich Xe isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, I.; Lister, C.J.; Morss, L.R. [and others

    1995-08-01

    The level structures of neutron-rich Xe isotopes were determined by observing prompt gamma-ray coincidences in {sup 248}Cm fission fragments. A 5-mg {sup 248}Cm, in the form of {sup 248}Cm-KCl pellet, was placed inside Eurogam array which consisted of 45 Compton-suppressed Ge detectors and 5 Low-Energy Photon Spectrometers. Transitions in Xe isotopes were identified by the appearance of new peaks in the {gamma}-ray spectra obtained by gating on the gamma peaks of the complementary Mo fragments.

  13. Evaluation of Yield and Yield Attributes of Five Sweet Potato ...

    African Journals Online (AJOL)

    0087, and TIS 2532.OP.1.13) were evaluated for yield and agronomic performance in Imo State University Farm, Owerri. The experiment was laid out in a randomised complete block design with three replications. The planting density was 33,000 ...

  14. Heterosis and combining ability for grain yield and yield component ...

    African Journals Online (AJOL)

    ... ranged from 0 to -13% indicating that the hybrids tend to be earlier in maturity than the parents. The mean squares due to GCA for days to maturity, ear diameter, member of kernels per row, 1000 kernel weight and grain yield were significant, indicating the importance of additive genetic variance in controlling these traits.

  15. Rice yield prediction from yield components and limiting factors

    NARCIS (Netherlands)

    Casanova, D.; Goudriaan, J.; Catala Former, M.M.; Withagen, J.C.M.

    2002-01-01

    This article aims to quantify growth at field level in relation to crop status and soil properties in irrigated direct-seeded rice. Forty fields were selected in the Ebro Delta (Spain). Rice growth was monitored and soil properties measured. Yield was related to soil properties by a deductive

  16. The leucine-rich repeat structure.

    Science.gov (United States)

    Bella, J; Hindle, K L; McEwan, P A; Lovell, S C

    2008-08-01

    The leucine-rich repeat is a widespread structural motif of 20-30 amino acids with a characteristic repetitive sequence pattern rich in leucines. Leucine-rich repeat domains are built from tandems of two or more repeats and form curved solenoid structures that are particularly suitable for protein-protein interactions. Thousands of protein sequences containing leucine-rich repeats have been identified by automatic annotation methods. Three-dimensional structures of leucine-rich repeat domains determined to date reveal a degree of structural variability that translates into the considerable functional versatility of this protein superfamily. As the essential structural principles become well established, the leucine-rich repeat architecture is emerging as an attractive framework for structural prediction and protein engineering. This review presents an update of the current understanding of leucine-rich repeat structure at the primary, secondary, tertiary and quaternary levels and discusses specific examples from recently determined three-dimensional structures.

  17. Status of fission yield data

    International Nuclear Information System (INIS)

    England, T.R.; Blachot, J.

    1988-01-01

    In this paper we summarize the current status of the recent US evaluation for 34 fissioning nuclides at one or more neutron incident energies and for spontaneous fission. Currently there are 50 yields sets, and for each we have independent and cumulative yields and uncertainties for approximately 1100 fission products. When finalized the recommended data will become part of Version VI of the US ENDF/B. Other major evaluations in progress that are included in a recently formed IAEA Coordinated Research Program are also summarized. In a second part we review two empirical models in use to estimate independent yields. Comparison of model estimates with measured data is presented, including a comparison with some recent data obtained from Lohengrin (Cf-249 T). 18 refs., 13 figs., 3 tabs

  18. The effects of microalloying with Cd on precipitation processes in Al-1.7 Cu-0.3 mg (At. %) alloys

    International Nuclear Information System (INIS)

    Sofyan, Bondan T.

    2002-01-01

    The present work investigates the effects of microalloying with Cd on precipitation processes in Al-1.7 Cu-0.3 mg (At. %) alloys. Analytical STEM (Scanning Transmission Electron Microscope) revealed the presence of clusters rich in Cd and Mg at early stages of ageing, which is believed to be responsible in promoting the nucleation of θ (Al,Cu) in the alloy on its (001) planes. The Cd-Mg clusters then grow as Cd-Mg-rich particles when ageing is continued beyond the peak hardness. The presence of Cd-Mg-rich clusters is thought to play an important role on the nucleation of θ phase by accommodating the misfit strain on the non-coherent rim of the phase. The accommodation of misfit strain is made available by the presence of large amount of vacancies, which is trapped by Cd and Mg atoms during quenching, around θ platelet nuclei

  19. Microstructure, corrosion behavior and cytotoxicity of biodegradable Mg-Sn implant alloys prepared by sub-rapid solidification.

    Science.gov (United States)

    Zhao, Chaoyong; Pan, Fusheng; Zhao, Shuang; Pan, Hucheng; Song, Kai; Tang, Aitao

    2015-09-01

    In this study, biodegradable Mg-Sn alloys were fabricated by sub-rapid solidification, and their microstructure, corrosion behavior and cytotoxicity were investigated by using optical microscopy, scanning electron microscopy equipped with an energy dispersive X-ray spectroscopy, X-ray diffraction, immersion test, potentiodynamic polarization test and cytotoxicity test. The results showed that the microstructure of Mg-1Sn alloy was almost equiaxed grain, while the Mg-Sn alloys with higher Sn content (Sn≥3 wt.%) displayed α-Mg dendrites, and the secondary dendrite arm spacing of the primary α-Mg decreased significantly with increasing Sn content. The Mg-Sn alloys consisted of primary α-Mg matrix, Sn-rich segregation and Mg2Sn phase, and the amount of Mg2Sn phases increased with increasing Sn content. Potentiodynamic polarization and immersion tests revealed that the corrosion rates of Mg-Sn alloys increased with increasing Sn content. Cytotoxicity test showed that Mg-1Sn and Mg-3Sn alloys were harmless to MG63 cells. These results of the present study indicated that Mg-1Sn and Mg-3Sn alloys were promising to be used as biodegradable implants. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. Spinodal instability of baryon-rich quark matter

    International Nuclear Information System (INIS)

    Li, Feng; Ko, Che Ming

    2017-01-01

    The spinodal instabilities of both confined and expanding baryon-rich quark matters are studied in a transport model derived from the Nambu-Jona-Lasino model. Appreciable higher-order density moments are seen as a result of the first-order phase transition in both cases. The skewness of the quark number event-by-event distribution in a small subvolume of the system becomes appreciable for the confined quark matter. For the expanding quark matter, the density fluctuations lead to enhanced anisotropic flows and dilepton yield. (paper)

  1. Isotopic Hg in an Allende carbon-rich residue

    Science.gov (United States)

    Reed, G. W., Jr.; Jovanovic, S.

    1990-01-01

    A carbon-rich residue from Allende subjected to stepwise heating yielded two isotopically resolvable types of Hg: one with an (Hg-196)/(Hg-202) concentration ratio the same as terrestrial (monitor) Hg; the other enriched in Hg-196 relative to Hg-202 by about 60 percent. Hg with the 202 isotope enriched relative to 196, as is found in bulk Allende, was not observed. Whether the result of mass fractionation or nucleosynthesis, the distinct types of Hg entered different carrier phases and were not thermally mobilized since the accretion of the Allende parent body.

  2. Isotopic Hg in an Allende carbon-rich residue

    International Nuclear Information System (INIS)

    Reed, G.W. Jr.; Jovanovic, S.

    1990-01-01

    A carbon-rich residue from Allende subjected to stepwise heating yielded two isotopically resolvable types of Hg: one with an (Hg-196)/(Hg-202) concentration ratio the same as terrestrial (monitor) Hg; the other enriched in Hg-196 relative to Hg-202 by about 60 percent. Hg with the 202 isotope enriched relative to 196, as is found in bulk Allende, was not observed. Whether the result of mass fractionation or nucleosynthesis, the distinct types of Hg entered different carrier phases and were not thermally mobilized since the accretion of the Allende parent body. 9 refs

  3. Preparation of proton rich radionuclides in support of radiochemical analysis

    International Nuclear Information System (INIS)

    Jerome, Simon; Larijani, Cyrus; Parker, David

    2012-01-01

    The production of proton rich radionuclides supports a wide range of radiochemical analyses via radioactive yield tracers ( 95m Tc and 236 Pu). In recent years, NPL and the University of Birmingham cyclotron have collaborated to produce these, and other, radionuclides. - Highlights: ► In this paper we options for the production of Tc and Pu tracers. ► The irradiation and measurement of targets producing Tc-95 m and Pu-236 are described. ► Options for production are discussed. ► The results of this study and future work needed are described.

  4. Rich Language Analysis for Counterterrorism

    Science.gov (United States)

    Guidère, Mathieu; Howard, Newton; Argamon, Shlomo

    Accurate and relevant intelligence is critical for effective counterterrorism. Too much irrelevant information is as bad or worse than not enough information. Modern computational tools promise to provide better search and summarization capabilities to help analysts filter and select relevant and key information. However, to do this task effectively, such tools must have access to levels of meaning beyond the literal. Terrorists operating in context-rich cultures like fundamentalist Islam use messages with multiple levels of interpretation, which are easily misunderstood by non-insiders. This chapter discusses several kinds of such “encryption” used by terrorists and insurgents in the Arabic language, and how knowledge of such methods can be used to enhance computational text analysis techniques for use in counterterrorism.

  5. N and P addition inhibits growth of rich fen bryophytes

    DEFF Research Database (Denmark)

    Andersen, Dagmar Kappel; Ejrnæs, Rasmus; Riis, Tenna

    2016-01-01

    vernicosus and paludella squarrosa) rich fen bryophytes were grown in mixed culture and subjected to rainwater or groundwater and three levels of N (0, 1 and 3 mg N L-1) and P (0, 0.05 and 0.1 mg P NL-1). All species responded negatively to higher N-levels and three of four species responded negatively...... to rainwater and higher P-levels. C. cuspidata had highest relative growth rate in all treatments, and the infrequently occurringrare species had lower relative growth rate and were more negatively affected by high levels of N than the frequently occurringcommon species. A negative effect of rainwater seemed...... to be caused by higher background levels of N in rainwater compared to groundwater rather than a pH-effect per se. We found a negative effect of high initial bryophyte density in three of four species indicating density dependent inhibition between species.We suggest that maintenance of oligotrophic conditions...

  6. Alterations of Mg2+ After Hemorrhagic Shock.

    Science.gov (United States)

    Lee, Mun-Young; Yang, Dong Kwon; Kim, Shang-Jin

    2017-11-01

    Hemorrhagic shock is generally characterized by hemodynamic instability with cellular hypoxia and diminishing cellular function, resulting from an imbalance between systemic oxygen delivery and consumption and redistribution of fluid and electrolytes. Magnesium (Mg) is the fourth most abundant cation overall and second most abundant intracellular cation in the body and an essential cofactor for the energy production and cellular metabolism. Data for blood total Mg (tMg; free-ionized, protein-bound, and anion-bound forms) and free Mg 2+ levels after a traumatic injury are inconsistent and only limited information is available on hemorrhagic effects on free Mg 2+ as the physiologically active form. The aim of this study was to determine changes in blood Mg 2+ and tMg after hemorrhage in rats identifying mechanism and origin of the changes in blood Mg 2+ . Hemorrhagic shock produced significant increases in blood Mg 2+ , plasma tMg, Na + , K + , Cl - , anion gap, partial pressures of oxygen, glucose, and blood urea nitrogen but significant decreases in RBC tMg, blood Ca 2+ , HCO 3 - , pH, partial pressures of carbon dioxide, hematocrit, hemoglobin, total cholesterol, and plasma/RBC ATP. During hemorrhagic shock, K + , anion gap, and BUN showed significant positive correlations with changes in blood Mg 2+ level, while Ca 2+ , pH, and T-CHO correlated to Mg 2+ in a negative manner. In conclusion, hemorrhagic shock induced an increase in both blood-free Mg 2+ and tMg, resulted from Mg 2+ efflux from metabolic damaged cell with acidosis and ATP depletion.

  7. Iron-Rich Carbonates as the Potential Source of Evolved CO2 Detected by the Sample Analysis at Mars (SAM) Instrument in Gale Crater

    Science.gov (United States)

    Sutter, B.; Heil, E.; Rampe, E. B.; Morris, R. V.; Ming, D. W.; Archer, P. D.; Eigenbrode, J. L.; Franz, H. B.; Glavin, D. P.; McAdam, A. C.; hide

    2015-01-01

    The Sample Analysis at Mars (SAM) instrument detected at least 4 distinct CO2 release during the pyrolysis of a sample scooped from the Rocknest (RN) eolian deposit. The highest peak CO2 release temperature (478-502 C) has been attributed to either a Fe-rich carbonate or nano-phase Mg-carbonate. The objective of this experimental study was to evaluate the thermal evolved gas analysis (T/EGA) characteristics of a series of terrestrial Fe-rich carbonates under analog SAM operating conditions to compare with the RN CO2 releases. Natural Fe-rich carbonates (<53 microns) with varying Fe amounts (Fe(0.66)X(0.34)- to Fe(0.99)X(0.01)-CO3, where X refers to Mg and/or Mn) were selected for T/EGA. The carbonates were heated from 25 to 715 C (35 C/min) and evolved CO2 was measured as a function of temperature. The highest Fe containing carbonates (e.g., Fe(0.99)X(0.01)-CO3) yielded CO2 peak temperatures between 466-487 C, which is consistent with the high temperature RN CO2 release. The lower Fe-bearing carbonates (e.g., Fe(0.66)X(0.34)CO3) did not have peak CO2 release temperatures that matched the RN peak CO2 temperatures; however, their entire CO2 releases did occur within RN temperature range of the high temperature CO2 release. Results from this laboratory analog analysis demonstrate that the high temperature RN CO2 release is consistent with Fe-rich carbonate (approx.0.7 to 1 wt.% FeCO3). The similar RN geochemistry with other materials in Gale Crater and elsewhere on Mars (e.g., Gusev Crater, Meridiani) suggests that up to 1 wt. % Fe-rich carbonate may occur throughout the Gale Crater region and could be widespread on Mars. The Rocknest Fe-carbonate may have formed from the interaction of reduced Fe phases (e.g., Fe2+ bearing olivine) with atmospheric CO2 and transient water. Alternatively, the Rocknest Fe-carbonate could be derived by eolian processes that have eroded distally exposed deep crustal material that possesses Fe-carbonate that may have formed through

  8. Assessing potential sustainable wood yield

    Science.gov (United States)

    Robert F. Powers

    2001-01-01

    Society is making unprecedented demands on world forests to produce and sustain many values. Chief among them is wood supply, and concerns are rising globally about the ability of forests to meet increasing needs. Assessing this is not easy. It requires a basic understanding of the principles governing forest productivity: how wood yield varies with tree and stand...

  9. NIF total neutron yield diagnostic

    International Nuclear Information System (INIS)

    Cooper, Gary W.; Ruiz, Carlos L.

    2001-01-01

    We have designed a total neutron yield diagnostic for the National Ignition Facility (NIF) which is based on the activation of In and Cu samples. The particular approach that we have chosen is one in which we calibrate the entire counting system and which we call the ''F factor'' method. In this method, In and/or Cu samples are exposed to known sources of DD and DT neutrons. The activated samples are then counted with an appropriate system: a high purity Ge detector for In and a NaI coincidence system for Cu. We can then calculate a calibration factor, which relates measured activity to total neutron yield. The advantage of this approach is that specific knowledge of such quantities as cross sections and detector efficiencies is not needed. Unless the actual scattering environment of the NIF can be mocked up in the calibration experiment, the F factor will have to be modified using the results of a numerical simulation of the NIF scattering environment. In this article, the calibration factor methodology will be discussed and experimental results for the calibration factors will be presented. Total NIF neutron yields of 10 9 --10 19 can be measured with this method assuming a 50 cm stand-off distance can be employed for the lower yields

  10. Robust Optical Richness Estimation with Reduced Scatter

    Energy Technology Data Exchange (ETDEWEB)

    Rykoff, E.S.; /LBL, Berkeley; Koester, B.P.; /Chicago U. /Chicago U., KICP; Rozo, E.; /Chicago U. /Chicago U., KICP; Annis, J.; /Fermilab; Evrard, A.E.; /Michigan U. /Michigan U., MCTP; Hansen, S.M.; /Lick Observ.; Hao, J.; /Fermilab; Johnston, D.E.; /Fermilab; McKay, T.A.; /Michigan U. /Michigan U., MCTP; Wechsler, R.H.; /KIPAC, Menlo Park /SLAC

    2012-06-07

    Reducing the scatter between cluster mass and optical richness is a key goal for cluster cosmology from photometric catalogs. We consider various modifications to the red-sequence matched filter richness estimator of Rozo et al. (2009b), and evaluate their impact on the scatter in X-ray luminosity at fixed richness. Most significantly, we find that deeper luminosity cuts can reduce the recovered scatter, finding that {sigma}{sub ln L{sub X}|{lambda}} = 0.63 {+-} 0.02 for clusters with M{sub 500c} {approx}> 1.6 x 10{sup 14} h{sub 70}{sup -1} M{sub {circle_dot}}. The corresponding scatter in mass at fixed richness is {sigma}{sub ln M|{lambda}} {approx} 0.2-0.3 depending on the richness, comparable to that for total X-ray luminosity. We find that including blue galaxies in the richness estimate increases the scatter, as does weighting galaxies by their optical luminosity. We further demonstrate that our richness estimator is very robust. Specifically, the filter employed when estimating richness can be calibrated directly from the data, without requiring a-priori calibrations of the red-sequence. We also demonstrate that the recovered richness is robust to up to 50% uncertainties in the galaxy background, as well as to the choice of photometric filter employed, so long as the filters span the 4000 {angstrom} break of red-sequence galaxies. Consequently, our richness estimator can be used to compare richness estimates of different clusters, even if they do not share the same photometric data. Appendix A includes 'easy-bake' instructions for implementing our optimal richness estimator, and we are releasing an implementation of the code that works with SDSS data, as well as an augmented maxBCG catalog with the {lambda} richness measured for each cluster.

  11. Correlation of superconducting properties and microstructure in MgB{sub 2} using SEM, EPMA and TEM

    Energy Technology Data Exchange (ETDEWEB)

    Birajdar, Balaji I.

    2008-04-14

    This thesis can be subdivided as follows: (I) Development of the quantitative electron microscopy and spectroscopy methods essential for the microstructural analysis of MgB{sub 2} and thereby assess the performance of two energy-filtered TEMs. (II) Application of these methods to few selected samples: (a) Pure and Al-alloyed MgB{sub 2} bulk samples prepared by solid-state reaction or by mechanical alloying, (b) In-situ and ex-situ MgB{sub 2} wires and tapes with and without SiC additives prepared by different variants of the powder-in-tube technology. Quantitative B analysis by EDX spectroscopy was applied in the SEM and TEM, which is a major achievement. (III) Establishing a model which quantitatively explains the correlation between microstructure and critical current density as a function of magnetic field. The actual Al mole fraction in the MgB{sub 2} matrix was found to be less than the nominal Al mole fraction and the difference increased with increasing Al mole fraction. Al is incorporated into MgB{sub 2} grains of {approx}1{mu}m size by substitution of Mg atoms causing T{sub c} and c lattice parameter to decrease at a rate of 1.56 K and 1.15 pm per at.% of Al alloying. Precipitation of Al was not detected up to highest Al mole fractions but Al was inhomogeneously distributed in the sample, which explained the broadening of the superconducting transition width ({delta}T{sub c}) with increasing Al mole fraction. For wires and tapes, significant differences were observed in the microstructure of in-situ and ex-situ samples. This holds particularly if SiC was added and yielded Mg{sub 2}Si for in-situ samples annealed at 600 -650 C and Mg-Si-O phases for ex-situ samples annealed between 900 -1050 C. Four microstructural parameters were identified as relevant for the I{sub c} of wires and tapes and these were: 1) MgB{sub 2} grain size which lies in the range of 20-1000 nm, 2) colony size (colony is a dense arrangement of MgB{sub 2} grains) which lies in the range

  12. Modeling and stabilities of Mg/MgH2 interfaces: A first-principles investigation

    Directory of Open Access Journals (Sweden)

    Jia-Jun Tang

    2014-07-01

    Full Text Available We have theoretically investigated the modeling and the structural stabilities of various Mg/MgH2 interfaces, i.e. Mg(101¯0/MgH2(210, Mg(0001/MgH2(101 and Mg(101¯0/MgH2(101, and provided illuminating insights into Mg/MgH2 interface. Specifically, the main factors, which impact the interfacial energies, are fully considered, including surface energies of two phases, mutual lattice constants of interface model, and relative position of two phases. The surface energies of Mg and MgH2, on the one hand, are found to be greatly impacting the interfacial energies, reflected by the lowest interfacial energy of Mg(0001/MgH2(101 which is comprised of two lowest energy surfaces. On the other hand, it is demonstrated that the mutual lattice constants and the relative position of two phases lead to variations of interfacial energies, thus influencing the interface stabilities dramatically. Moreover, the Mg-H bonding at interface is found to be the determinant of Mg/MgH2 interface stability. Lastly, interfacial and strain effects on defect formations are also studied, both of which are highly facilitating the defect formations. Our results provide a detailed insight into Mg/MgH2 interface structures and the corresponding stabilities.

  13. The Role of KREEP in the Production of Mg-Suite Magmas and Its Influence on the Extent of Mg-Suite Magmatism in the Lunar Crust

    Science.gov (United States)

    Elardo, S. M.; Shearer, C. K.; McCubbin, F. M.

    2017-01-01

    The lunar magnesian-suite, or Mg-suite, is a series of ancient plutonic rocks from the lunar crust. They have received a considerable amount of attention from lunar scientists since their discovery for three primary reasons: 1) their ages and geochemistry indicate they represent pristine magmatic samples that crystallized very soon after the formation of the Moon; 2) their ages often overlap with ages of the ferroan anorthosite (FAN) crust; and 3) planetary-scale processes are needed in formation models to account for their unique geochemical features. Taken as a whole, the Mg-suite samples, as magmatic cumulate rocks, approximate a fractional crystallization sequence in the low-pressure forsterite-anorthite-silica system, and thus these samples are generally thought to be derived from layered mafic intrusions which crystallized very slowly from magmas that intruded the anorthositic crust. However, no direct linkages have been established between different Mg-suite samples based either on field relationships or geochemistry.The model for the origin of the Mg-suite, which best fits the limited available data, is one where Mg-suite magmas form from melting of a hybrid cumulate package consisting of deep mantle dunite, crustal anorthosite, and KREEP (potassium-rare earth elements-phosphorus) at the base of the crust under the Procellarum KREEP Terrane (PKT). In this model, these three LMO (Lunar Magma Ocean) cumulate components are brought into close proximity by the cumulate overturn process. Deep mantle dunitic cumulates with an Mg number of approximately 90 rise to the base of the anorthositic crust due to their buoyancy relative to colder, more dense Fe- and Ti-rich cumulates. This hybridized source rock melts to form Mg-suite magmas, saturated in Mg-rich olivine and anorthitic plagioclase, that have a substantial KREEP component.

  14. GENETIC ANALYSIS OF YIELD AND YIELD COMPONENTS IN ...

    African Journals Online (AJOL)

    ACSS

    2017-11-16

    Nov 16, 2017 ... used different genotypes and the environmental conditions under which their ... and Jinks (1971):. Y = m + aa + βd + a2aa + 2aβad +β2dd … .... /plant, 100-grain weight per plant and Grain yield per plant (g) of six generations in IET6279 X IR70445-146-3-. 3 cross. Traits. Generation. Mean. Standard. Range.

  15. Potato yield and yield structure depending on irrigation

    Directory of Open Access Journals (Sweden)

    Milić Stanko

    2010-01-01

    Full Text Available In the agroclimatic conditions of the Vojvodina Province, the application of an economic water regime and modern technology is necessary for stable and intensive potato production. A two-year experiment on calcareous chernozem was carried out to determine how irrigation and different pre-irrigation soil moisture affect potato yield and distribution of tuber fraction in the potato yield. The block-design trial had four replicates and was adapted for sprinkler irrigation conditions. It included four treatments: irrigation with pre-irrigation moisture levels of 60 % of field water capacity (FC, irrigation with pre-irrigation moisture levels of 70 % (FC, irrigation with pre-irrigation moisture levels of 80% (FC, and a non-irrigated control treatment. Irrigation significantly increased the yield of potato, which increased from 37.27 % to 75.86 %. Under irrigation, the percentage of small fractions decreased in favour of the 55 mm one, or fractions above the 45-55 mm range. On average, irrigated treatments produced significantly more tubers than the conditions of natural water supply. .

  16. Mutually beneficial pollinator diversity and crop yield outcomes in small and large farms.

    Science.gov (United States)

    Garibaldi, Lucas A; Carvalheiro, Luísa G; Vaissière, Bernard E; Gemmill-Herren, Barbara; Hipólito, Juliana; Freitas, Breno M; Ngo, Hien T; Azzu, Nadine; Sáez, Agustín; Åström, Jens; An, Jiandong; Blochtein, Betina; Buchori, Damayanti; Chamorro García, Fermín J; Oliveira da Silva, Fabiana; Devkota, Kedar; Ribeiro, Márcia de Fátima; Freitas, Leandro; Gaglianone, Maria C; Goss, Maria; Irshad, Mohammad; Kasina, Muo; Pacheco Filho, Alípio J S; Kiill, Lucia H Piedade; Kwapong, Peter; Parra, Guiomar Nates; Pires, Carmen; Pires, Viviane; Rawal, Ranbeer S; Rizali, Akhmad; Saraiva, Antonio M; Veldtman, Ruan; Viana, Blandina F; Witter, Sidia; Zhang, Hong

    2016-01-22

    Ecological intensification, or the improvement of crop yield through enhancement of biodiversity, may be a sustainable pathway toward greater food supplies. Such sustainable increases may be especially important for the 2 billion people reliant on small farms, many of which are undernourished, yet we know little about the efficacy of this approach. Using a coordinated protocol across regions and crops, we quantify to what degree enhancing pollinator density and richness can improve yields on 344 fields from 33 pollinator-dependent crop systems in small and large farms from Africa, Asia, and Latin America. For fields less than 2 hectares, we found that yield gaps could be closed by a median of 24% through higher flower-visitor density. For larger fields, such benefits only occurred at high flower-visitor richness. Worldwide, our study demonstrates that ecological intensification can create synchronous biodiversity and yield outcomes. Copyright © 2016, American Association for the Advancement of Science.

  17. Microstructure and Mechanical Properties of Dissimilar Joints of Al-Mg2Si and 5052 Aluminum Alloy by Friction Stir Welding

    Science.gov (United States)

    Huang, B. W.; Qin, Q. D.; Zhang, D. H.; Wu, Y. J.; Su, X. D.

    2018-03-01

    Al-Mg2Si alloy and 5052 Al alloy were welded successfully by friction stir welding (FSW) in this study. The results show that the alloy consists of three distinct zones after FSW: the base material zone (BMZ), the transitional zone, and the weld nugget (WN). The morphologies of the primary Mg2Si phases are identified as coarse equiaxed crystals for Al-Mg2Si alloys in the BMZ. The WN is a mixture of rich Al-Mg2Si and rich 5052 alloy, and a banded structure is formed in the zone. Interestingly, in the WN, the equiaxed crystals changed to polygonal particles with substantially reduced sizes in the rich Al-Mg2Si zone. However, in addition to the white rich Mg phase appearing in the rich 5052 zone near the interface, the 5052 alloy does not show obvious changes. The hardness gradually increases from the BMZ of the 5052 to the welded joint to the Al-Mg2Si BMZ. In addition, the ultimate tensile strength (UTS) of the welded joint is higher than that of the base material of the Al-Mg2Si, whereas it is lower than that of the 5052 base alloy. The results of the elongation are similar to the UTS results. The fracture mechanism is also investigated.

  18. Mg substituted apatite coating from alkali conversion of acidic calcium phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Navarro da Rocha, Daniel, E-mail: dnr.navarro@gmail.com [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Cruz, Leila Rosa de Oliveira [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Campos, José Brant de [Rio de Janeiro State University - UERJ, Rio de Janeiro, R.J. (Brazil); Marçal, Rubens L. Santana Blazutti [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil); Mijares, Dindo Q.; Coelho, Paulo G. [Department of Biomaterials and Biomimetics, New York University College of Dentistry (NYU), New York, NY (United States); Prado da Silva, Marcelo H. [Military Institute of Engineering-IME, Pça. Gen. Tiburcio, 80, P. Vermelha, Urca, Rio de Janeiro, R.J. (Brazil)

    2017-01-01

    In this work, two solutions were developed: the first, rich in Ca{sup 2+}, PO{sub 4}{sup 3−} ions and the second, rich in Ca{sup 2+}, PO{sub 4}{sup 3−} and Mg{sup 2+}, defined as Mg-modified precursor solution. For each Mg-modified precursor solution, the concentrations of Mg{sup 2+} ions were progressively increased by 5%, 10% and 15%wt. The aims of this research were to investigate the influence of magnesium ions substitution in calcium phosphate coatings on titanium surface and to evaluate these coatings by bioactivity assay in McCoy culture medium. The obtained coatings were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analysis, and the presence of Mg ions was confirmed by the inductively coupled plasma atomic emission spectroscopy (ICP) analysis. In vitro bioactivity assay in McCoy culture medium showed bioactivity after 14 days in incubation for the HA and 10% Mg-monetite coatings. The high chemical stability of Mg-HA coatings was verified by the bioactivity assays, and no bone-like apatite deposition, characteristic of bioactivity, was observed for Mg-HA coatings, for the time period used in this study. - Highlights: • The presence of Mg ions influenced the final apatite phase present in the produced coatings. • A lower efficiency in heterogeneous deposition and an exposure of Ti substrate in 5% Mg-monetite coatings was soon verified. • McCoy culture medium was effective in predicting the coatings bioactivity.

  19. Isotopic evidence for primordial molecular cloud material in metal-rich carbonaceous chondrites

    DEFF Research Database (Denmark)

    van Kooten, Elishevah M. M. E.; Wielandt, Daniel Kim Peel; Schiller, Martin

    2016-01-01

    product of (26)Al. This correlation is interpreted as reflecting progressive thermal processing of in-falling (26)Al-rich molecular cloud material in the inner Solar System. The thermally unprocessed molecular cloud matter reflecting the nucleosynthetic makeup of the molecular cloud before the last......)Mg*-depleted and (54)Cr-enriched component. This composition is consistent with that expected for thermally unprocessed primordial molecular cloud material before its pollution by stellar-derived (26)Al. The (26)Mg* and (54)Cr compositions of bulk metal-rich chondrites require significant amounts (25......-50%) of primordial molecular cloud matter in their precursor material. Given that such high fractions of primordial molecular cloud material are expected to survive only in the outer Solar System, we infer that, similarly to cometary bodies, metal-rich carbonaceous chondrites are samples of planetesimals...

  20. High production rate of IBAD-MgO buffered substrate

    Energy Technology Data Exchange (ETDEWEB)

    Yoshizumi, M., E-mail: myoshizumi@istec.or.j [Superconductivity Research Laboratory, ISTEC, Shinonome 1-10-13, Koto-ku, Tokyo 135-0062 (Japan); Miyata, S.; Ibi, A.; Fukushima, H.; Yamada, Y.; Izumi, T.; Shiohara, Y. [Superconductivity Research Laboratory, ISTEC, Shinonome 1-10-13, Koto-ku, Tokyo 135-0062 (Japan)

    2009-10-15

    The conventional IBAD (Ion Beam Assisted Deposition) process using fluorite materials yields low production rates, resulting in high production cost, which reduces the motivation for practical application in spite of its high quality. The IBAD process using rock salt materials, e.g. MgO, is well known as a strong candidate of practical application due to its potential of high production rate and high in-plane grain alignment. In this work, the IBAD-MgO process was investigated for a newly developed architecture of PLD (Pulsed Laser Deposition)-CeO{sub 2}/sputter-LMO (LaMnO{sub 3})/IBAD-MgO/sputter-GZO (Gd{sub 2}Zr{sub 2}O{sub 7})/Hastelloy{sup TM} to make long buffered metal tapes with high properties and a high production rate. The 50 m-long IBAD-MgO substrates with about 4 deg. of DELTAphiCeO{sub 2} in an XRD phi scan could be fabricated repeatedly. A GdBCO (GdBa{sub 2}Cu{sub 3}O{sub x}) layer deposited on the buffered substrate showed the minimum I{sub c} value of 325 A/cm-w in a 41 m-long tape. Almost of the tape showed 500-600 A/cm-w of I{sub c} value. The deposition time for the IBAD-MgO layer was 60 s which was about 2 orders of magnitude shorter than the conventional IBAD process. The production rate of 24 m/h was realized at the IBAD-MgO process to fabricate the GdBCO coated conductor with high J{sub c} and I{sub c} properties.

  1. CALCIUM-RICH GAP TRANSIENTS: SOLVING THE CALCIUM CONUNDRUM IN THE INTRACLUSTER MEDIUM

    International Nuclear Information System (INIS)

    Mulchaey, John S.; Kollmeier, Juna A.; Kasliwal, Mansi M.

    2014-01-01

    X-ray measurements suggest that the abundance of calcium in the intracluster medium is higher than can be explained using favored models for core-collapse and Type Ia supernovae alone. We investigate whether the ''calcium conundrum'' in the intracluster medium can be alleviated by including a contribution from the recently discovered subclass of supernovae known as calcium-rich gap transients. Although the calcium-rich gap transients make up only a small fraction of all supernovae events, we find that their high calcium yields are sufficient to reproduce the X-ray measurements found for nearby rich clusters. We find the χ 2 goodness-of-fit metric improves from 84 to 2 by including this new class. Moreover, calcium-rich supernovae preferentially occur in the outskirts of galaxies making it easier for the nucleosynthesis products of these events to be incorporated in the intracluster medium via ram-pressure stripping. The discovery of calcium-rich gap transients in clusters and groups far from any individual galaxy suggests that supernovae associated with intracluster stars may play an important role in enriching the intracluster medium. Calcium-rich gap transients may also help explain anomalous calcium abundances in many other astrophysical systems including individual stars in the Milky Way, the halos of nearby galaxies, and the circumgalactic medium. Our work highlights the importance of considering the diversity of supernovae types and corresponding yields when modeling the abundance of the intracluster medium and other gas reservoirs

  2. Permanent magnet with MgB{sub 2} bulk superconductor

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Akiyasu, E-mail: yamamoto@appchem.t.u-tokyo.ac.jp [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); JST-PRESTO, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Ishihara, Atsushi; Tomita, Masaru [Railway Technical Research Institute, 2-8-38 Hikari, Kokubunji, Tokyo 185-8540 (Japan); Kishio, Kohji [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan)

    2014-07-21

    Superconductors with persistent zero-resistance currents serve as permanent magnets for high-field applications requiring a strong and stable magnetic field, such as magnetic resonance imaging. The recent global helium shortage has quickened research into high-temperature superconductors (HTSs)—materials that can be used without conventional liquid-helium cooling to 4.2 K. Herein, we demonstrate that 40-K-class metallic HTS magnesium diboride (MgB{sub 2}) makes an excellent permanent bulk magnet, maintaining 3 T at 20 K for 1 week with an extremely high stability (<0.1 ppm/h). The magnetic field trapped in this magnet is uniformly distributed, as for single-crystalline neodymium-iron-boron. Magnetic hysteresis loop of the MgB{sub 2} permanent bulk magnet was determined. Because MgB{sub 2} is a simple-binary-line compound that does not contain rare-earth metals, polycrystalline bulk material can be industrially fabricated at low cost and with high yield to serve as strong magnets that are compatible with conventional compact cryocoolers, making MgB{sub 2} bulks promising for the next generation of Tesla-class permanent-magnet applications.

  3. Yield trends and yield gap analysis of major crops in the world

    OpenAIRE

    Hengsdijk, H.; Langeveld, J.W.A.

    2009-01-01

    This study aims to quantify the gap between current and potential yields of major crops in the world, and the production constraints that contribute to this yield gap. Using an expert-based evaluation of yield gaps and the literature, global and regional yields and yield trends of major crops are quantified, yield gaps evaluated by crop experts, current yield progress by breeding estimated, and different yield projections compared. Results show decreasing yield growth for wheat and rice, but ...

  4. Proton-rich nuclear statistical equilibrium

    International Nuclear Information System (INIS)

    Seitenzahl, I.R.; Timmes, F.X.; Marin-Lafleche, A.; Brown, E.; Magkotsios, G.; Truran, J.

    2008-01-01

    Proton-rich material in a state of nuclear statistical equilibrium (NSE) is one of the least studied regimes of nucleosynthesis. One reason for this is that after hydrogen burning, stellar evolution proceeds at conditions of an equal number of neutrons and protons or at a slight degree of neutron-richness. Proton-rich nucleosynthesis in stars tends to occur only when hydrogen-rich material that accretes onto a white dwarf or a neutron star explodes, or when neutrino interactions in the winds from a nascent proto-neutron star or collapsar disk drive the matter proton-rich prior to or during the nucleosynthesis. In this Letter we solve the NSE equations for a range of proton-rich thermodynamic conditions. We show that cold proton-rich NSE is qualitatively different from neutron-rich NSE. Instead of being dominated by the Fe-peak nuclei with the largest binding energy per nucleon that have a proton-to-nucleon ratio close to the prescribed electron fraction, NSE for proton-rich material near freezeout temperature is mainly composed of 56Ni and free protons. Previous results of nuclear reaction network calculations rely on this nonintuitive high-proton abundance, which this Letter explains. We show how the differences and especially the large fraction of free protons arises from the minimization of the free energy as a result of a delicate competition between the entropy and nuclear binding energy.

  5. Controllable synthesis of carbon nanotubes by changing the Mo content in bimetallic Fe-Mo/MgO catalyst

    International Nuclear Information System (INIS)

    Xu Xiangju; Huang Shaoming; Yang Zhi; Zou Chao; Jiang Junfan; Shang Zhijie

    2011-01-01

    Research highlights: → Increasing the Mo content in the Fe-Mo/MgO catalysts resulted in an increase in wall number, diameter and growth yield of carbon nanotubes. → The Fe interacts with MgO to form complex (MgO) x (FeO) 1-x (0 4 and relative large metal Mo particles can be generated after reduction. → The avalanche-like reduction of MgMoO 4 makes the catalyst particles to be small thus enhances the utilize efficiency of Fe nanoparticles. - Abstract: A series of Fe-Mo/MgO catalysts with different Mo content were prepared by combustion method and used as catalysts for carbon nanotube (CNT) growth. Transmission electron microscopy studies of the nanotubes show that the number of the CNT walls and the CNT diameters increase with the increasing of Mo content in the bimetallic catalyst. The growth yield determined by thermogravimetric analysis also follows the trend: the higher the Mo content, the higher the yield of the CNTs. However, the increase of Mo content leads to the lower degree of graphitization of CNTs. A comparative study on the morphology and catalytic functions of Fe/MgO, Mo/MgO and Fe-Mo/MgO catalysts was carried out by scanning electron microscopy and X-ray diffraction. It is found that the Fe interacts with MgO to form complexes and is then dispersed into the MgO support uniformly, resulting in very small Fe nanoparticles after reduction. The Mo interacts with MgO to form stoichiometry compound MgMoO 4 and relative large metal Mo particles can be generated after reduction. High yield CNTs with small diameter can be generated from Fe-Mo/MgO because the avalanche-like reduction of MgMoO 4 makes the catalyst particles to be small thus enhances the utilize efficiency of Fe nanoparticles.

  6. Elevated Lipoprotein(A Impairs Platelet Radiolabeling Yield

    Directory of Open Access Journals (Sweden)

    Susanne Granegger

    2015-02-01

    Full Text Available Objectives: Platelet radiolabeling in clinical routine usually results in labeling efficiencies (LE above 80%. A variety of risk factors and clinical conditions are known to impair platelet labeling yield, among them elevated triglycerides and low-density lipoproteins. The potential influence of lipoprotein(a (Lp(a, an atherogenic lipoprotein particle containing a kringle subunit, which is widely found in the proteins of fibrinolysis pathway, has never been studied. Normal Lp(a levels range below 30 mg/ dl. The exact prevalence of elevated Lp(a is unknown, most likely ranging below 10%. Even more rare is an isolated elevation despite an otherwise normal lipoprotein profile. Methods: We examined the role of isolated elevated Lp(a (> 50 mg/dl, ranging up to 440 mg/dl compared to patients with normal lipid profile. Platelets were radiolabeled with in-111-oxine at 37 °C for 5 minutes using ISORBE-consensus methodology. Results: The findings indicate that already at levels below 100 mg/dl Lp(a decreases LE. LE assessment after cross-incubation of hyper-Lp(a platelets with normal Lp(a plasma and vice versa reveals that platelets rather than the plasmatic environment are responsible for the deterioration of labeling yield. This behavior already has been reported for elevated low-density lipoproteins. Apparently, the quantitative influence of LDL and Lp(a/mg is comparable. Plotting the sum of LDL and Lp(a versus LE reveals a clear significant negative correlation. Conclusion: As extremely elevated Lp(a, particularly above 150 mg/dl, may significantly impair labeling results. We therefore recommend to include extremely elevated Lp(a into the list of parameters, which should be known before performing radiolabeling of human platelets.

  7. Effect of phosphorus level on nitrogen accumulation and yield in soybean

    International Nuclear Information System (INIS)

    You Yubo; Wu Dongmei; Gong Zhenping; Ma Chunmei

    2012-01-01

    In this paper, the 15 N labeling with sand culture was conducted to study effects of phosphorus level on nitrogen accumulation, nodule nitrogen fixation and yield of soybean plants. Results showed that nitrogen accumulation, fixation and yield of soybean plants all presented a single peak curve with improvement of phosphorus nutrition level, with the peak value of phosphorus concentration in nutrient solution of 31 mg/L. When phosphorus concentration of nutrient solution was 11 mg/L, no obvious promotion was found on the ratio of nodule nitrogen fixation when increasing phosphorus concentration again, However, when phosphorus concentration of nutrient solution was 21 mg/L, increasing phosphorus concentration again had no obvious promotion on soybean plant nitrogen accumulation, nodule nitrogen fixation accumulation and yield, indicating that effect of phosphorus nutrition level on nitrogen fixation was lower than that on yield formation level. (authors)

  8. Heavy metals and yield of cowpea cultivated under composted tannery sludge amendment

    Directory of Open Access Journals (Sweden)

    Iuna Carmo Ribeiro Gonçalves

    2014-04-01

    Full Text Available The study aimed to evaluate the phytoavailability of heavy metals (Cr, Cd, Ni and Pb concentrations in leaves and grains, and yield of cowpea (Vigna unguiculata L grown in soil amended with composted tannery sludge (CTS for two consecutive years. The experiments were carried out in 2009 and 2010 in soil amended with CTS at 0, 5, 10, 20, and 40 Mg ha-1. The CTS amendment rates applied were above 10 Mg ha-1, increased Cr concentrations in cowpea leaves. There were not increases in the heavy metals concentrations in cowpea grains after two years. In 2009, the application of CTS amendment did not promote increase in plant yield. However, in 2010, CTS amendment at 10 and 20 Mg ha-1 increased cowpea yield. The amendment of composted tannery sludge linearly increased linearly the concentration of Cr in the leaves of cowpea after two years. Composted tannery sludge promoted increases in cowpea yield.

  9. Genotypic Variation in Yield, Yield Components, Root Morphology and Architecture, in Soybean in Relation to Water and Phosphorus Supply

    Science.gov (United States)

    He, Jin; Jin, Yi; Du, Yan-Lei; Wang, Tao; Turner, Neil C.; Yang, Ru-Ping; Siddique, Kadambot H. M.; Li, Feng-Min

    2017-01-01

    Water shortage and low phosphorus (P) availability limit yields in soybean. Roots play important roles in water-limited and P-deficient environment, but the underlying mechanisms are largely unknown. In this study we determined the responses of four soybean [Glycine max (L.) Merr.] genotypes [Huandsedadou (HD), Bailudou (BLD), Jindou 21 (J21), and Zhonghuang 30 (ZH)] to three P levels [applied 0 (P0), 60 (P60), and 120 (P120) mg P kg-1 dry soil to the upper 0.4 m of the soil profile] and two water treatment [well-watered (WW) and water-stressed (WS)] with special reference to root morphology and architecture, we compared yield and its components, root morphology and root architecture to find out which variety and/or what kind of root architecture had high grain yield under P and drought stress. The results showed that water stress and low P, respectively, significantly reduced grain yield by 60 and 40%, daily water use by 66 and 31%, P accumulation by 40 and 80%, and N accumulation by 39 and 65%. The cultivar ZH with the lowest daily water use had the highest grain yield at P60 and P120 under drought. Increased root length was positively associated with N and P accumulation in both the WW and WS treatments, but not with grain yield under water and P deficits. However, in the WS treatment, high adventitious and lateral root densities were associated with high N and P uptake per unit root length which in turn was significantly and positively associated with grain yield. Our results suggest that (1) genetic variation of grain yield, daily water use, P and N accumulation, and root morphology and architecture were observed among the soybean cultivars and ZH had the best yield performance under P and water limited conditions; (2) water has a major influence on nutrient uptake and grain yield, while additional P supply can modestly increase yields under drought in some soybean genotypes; (3) while conserved water use plays an important role in grain yield under drought

  10. 26Al-26Mg deficit dating ultramafic meteorites and silicate planetesimal differentiation in the early Solar System?

    DEFF Research Database (Denmark)

    Baker, Joel A.; Schiller, Martin; Bizzarro, Martin

    2012-01-01

    Meteorites with significantly sub-chondritic Al/Mg that formed in the first 2million years of the Solar System should be characterised by deficits in the abundance of Mg (d Mg ) due to the absence of in-growth of Mg from the decay of short-lived Al (t =0.73Myr). However, these Mg deficits...... will be small (d Mg >-0.037‰) even for material that formed at the same time as the Solar System's oldest solids - calcium-aluminium-rich inclusions - and thus measurement of these deficits is analytically challenging.Here, we report on a search for Mg deficits in three types of ultramafic meteorites...

  11. Bird communities and biomass yields in potential bioenergy grasslands.

    Directory of Open Access Journals (Sweden)

    Peter J Blank

    Full Text Available Demand for bioenergy is increasing, but the ecological consequences of bioenergy crop production on working lands remain unresolved. Corn is currently a dominant bioenergy crop, but perennial grasslands could produce renewable bioenergy resources and enhance biodiversity. Grassland bird populations have declined in recent decades and may particularly benefit from perennial grasslands grown for bioenergy. We asked how breeding bird community assemblages, vegetation characteristics, and biomass yields varied among three types of potential bioenergy grassland fields (grass monocultures, grass-dominated fields, and forb-dominated fields, and assessed tradeoffs between grassland biomass production and bird habitat. We also compared the bird communities in grassland fields to nearby cornfields. Cornfields had few birds compared to perennial grassland fields. Ten bird Species of Greatest Conservation Need (SGCN were observed in perennial grassland fields. Bird species richness and total bird density increased with forb cover and were greater in forb-dominated fields than grass monocultures. SGCN density declined with increasing vertical vegetation density, indicating that tall, dense grassland fields managed for maximum biomass yield would be of lesser value to imperiled grassland bird species. The proportion of grassland habitat within 1 km of study sites was positively associated with bird species richness and the density of total birds and SGCNs, suggesting that grassland bioenergy fields may be more beneficial for grassland birds if they are established near other grassland parcels. Predicted total bird density peaked below maximum biomass yields and predicted SGCN density was negatively related to biomass yields. Our results indicate that perennial grassland fields could produce bioenergy feedstocks while providing bird habitat. Bioenergy grasslands promote agricultural multifunctionality and conservation of biodiversity in working landscapes.

  12. Effect of Cs and Li atom adsorption on MgO: Secondary emission and work function

    International Nuclear Information System (INIS)

    Bagraev, N.T.; Borisov, V.L.

    1980-01-01

    Adsorption of Cs and Li atoms on the surface of single crystal magnesium oxide films has been investigated using Auger, LEED and contact difference techniques. A decreased work function for a single crystal MgO film grown on the Mo (100) face was observed to be accompanied by an increased secondary electron emission yield shown to be due to a larger escape depth for secondary electrons. LEED showed well ordered layers of adsorbed Cs on the MgO film surface. A model to explain the behaviour of Cs atoms on the film surface is proposed. It is shown that the stability of the Cs coating is not dependent on a prolonged bombardment of the film by incident electron beams of high current density. Depositing and implanting of thin single crystal MgO films with Li were found to result in an increased secondary electron emission yield, with Li adsorption on the MgO film surface being disordered. (orig.)

  13. Re-examining the 26Mg(α ,α')26Mg reaction: Probing astrophysically important states in 26Mg

    Science.gov (United States)

    Adsley, P.; Brümmer, J. W.; Li, K. C. W.; Marín-Lámbarri, D. J.; Kheswa, N. Y.; Donaldson, L. M.; Neveling, R.; Papka, P.; Pellegri, L.; Pesudo, V.; Pool, L. C.; Smit, F. D.; van Zyl, J. J.

    2017-11-01

    Background: The 22Ne(α ,n )25Mg reaction is one of the neutron sources for the s process in massive stars. The properties of levels in 26Mg above the α -particle threshold control the strengths of the 22Ne(α ,n )25Mg and 22Ne(α ,γ )26Mg reactions. The strengths of these reactions as functions of temperature are one of the major uncertainties in the s process. Purpose: Information on the existence, spin, and parity of levels in 26Mg can assist in constraining the strengths of the 22Ne(α ,γ )26Mg and 22Ne(α ,n )25Mg reactions, and therefore in constraining s -process abundances. Methods: Inelastically scattered α particles from a 26Mg target were momentum-analyzed in the K600 magnetic spectrometer at iThemba LABS, South Africa. The differential cross sections of states were deduced from the focal-plane trajectory of the scattered α particles. Based on the differential cross sections, spin and parity assignments to states are made. Results: A newly assigned 0+ state was observed in addition to a number of other states, some of which can be associated with states observed in other experiments. Some of the deduced Jπ values of the states observed in the present study show discrepancies with those assigned in a similar experiment performed at RCNP Osaka. The reassignments and additions of the various states can strongly affect the reaction rate at low temperatures. Conclusion: The number, location, and assignment of levels in 26Mg that may contribute to the 22Ne+α reactions are not clear. Future experimental investigations of 26Mg must have an extremely good energy resolution to separate the contributions from different levels. Coincidence experiments of 26Mg provide a possible route for future investigations.

  14. Nuclear shell effects in neutron-rich nuclei around N=20 and N=32,34

    International Nuclear Information System (INIS)

    Seidlitz, Michael

    2012-01-01

    Nuclear shell effects in neutron-rich nuclei around N=20 and N=32,34 were studied by means of reduced transition probabilities, i.e. B(E2) and B(M1) values. To this end a series of Coulomb-excitation experiments, employing radioactive 31 Mg and 29,30 Na beams, as well as a precise lifetime experiment of excited states in 56 Cr were performed. The collective properties of excited states of 31 Mg were the subject of a Coulomb-excitation experiment at REX-ISOLDE, CERN, employing a radioactive 31 Mg beam at a beam energy of 3.0 MeV/u. The beam intensity amounted to 3000 ions/s on average. The highly efficient MINIBALL setup was employed, consisting of eight HPGe cluster detectors for γ-ray detection and a segmented Si-detector for coincident particle detection. The level scheme of 31 Mg was extended. Spin and parity assignment of the observed 945 keV state yielded 5/2 + and its de-excitation is dominated by a strong collective M1 transition. Comparison of the transition probabilities of 30,31,32 Mg establishes that for the N=19 magnesium isotope not only the ground state but also excited states are largely dominated by a deformed pf intruder configuration. This implies that 31 Mg is part of the so-called ''island of inversion''. Coulomb-excitation experiments of radioactive 29,30 Na were carried out at REX-ISOLDE, CERN, at a final beam energy of 2.85 MeV/u. De-excitation γ rays were detected by the MINIBALL γ-ray spectrometer in coincidence with scattered particles in a segmented Si-detector. Despite rather low beam intensities transition probabilities to the first excited states were deduced. Results of very recently published experiments at MSU and TRIUMF could be largely confirmed and extended. The measured B(E2) values agree well with shell-model predictions, supporting the idea that in the sodium isotopic chain the ground-state wave function contains a significant intruder admixture already at N=18, with N=19 having an almost pure 2p2h deformed ground

  15. Micropropagation of Alibertia edulis Rich

    Directory of Open Access Journals (Sweden)

    Fernanda Augusta Boato da Silva

    2008-12-01

    Full Text Available The aim of this work was to develop a micropropagation protocol for Alibertia edulis, a medicinal Brazilian Cerrado plant. A. edulis seeds were sterilized and germinated in water-agar. Fifteen millimeter long explants from the seedlings cultivated for 50 days were used for the multiplication in three consecutive subcultures. The cytokinin benzyladenine (BA alone or combined with indole-3-butyric acid (IBA was added to ¼ MS medium. The treatments containing combinations of the BA + IBA induced more shoot proliferation than the BA alone, with the optimum concentration of 0.5 mg.L-1 for both growth regulators. A. edulis shoots elongated easily and the presence of growth regulators did have a positive effect on the shoot elongation. Consecutive subcultures also had a positive effect on both sprouting and shoot elongation. Activated charcoal was essential for rooting, and all rooted plants were able to acclimatize.Foi desenvolvido um protocolo de micropropagação para A. edulis, uma espécie arbórea frutífera e medicinal presente no Cerrado brasileiro. Sementes de A. edulis foram esterilizadas e germinadas em ágar-água. Explantes de 15 mm foram retirados das plântulas e cultivados por 50 dias em meio de multiplicação e três subculturas. A citocinina benzilalanina (BA, sozinha ou em combinação com ácido indol butírico (IBA foram adicionados em no meio ¼ MS. Os tratamentos contendo combinações de BA-IBA induziram uma maior proliferação de brotos que aqueles somente com BA, e a concentração ótima desses reguladores de crescimento foi de 0.5 mg.L-1 para cada. Os brotos de A. edulis facilmente se alongaram e a presença de reguladores de crescimento no meio de cultura teve efeito positivo sobre o alongamento. Da mesma forma, as consecutivas subculturas tiveram um efeito positivo tanto sobre a brotação quanto no alongamento. Carvão ativado foi essencial para o enraizamento dos ramos, e todas as plantas foram aclimatadas com sucesso.

  16. How Rice (Oryza sativa L.) Responds to Elevated As under Different Si-Rich Soil Amendments.

    Science.gov (United States)

    Teasley, William A; Limmer, Matthew A; Seyfferth, Angelia L

    2017-09-19

    Several strategies exist to mitigate As impacts on rice and each has its set of trade-offs with respect to yield, inorganic As content in grain, and CH 4 emissions. The addition of Si to paddy soil can decrease As uptake by rice but how rice will respond to elevated As when soil is amended with Si-rich materials is unresolved. Here, we evaluated yield impacts and grain As content and speciation in rice exposed to elevated As in response to different Si-rich soil amendments including rice husk, rice husk ash, and CaSiO 3 in a pot study. We found that As-induced yield losses were alleviated by Husk amendment, partially alleviated by Ash amendment, and not affected by CaSiO 3 amendment. Furthermore, Husk was the only tested Si-amendment to significantly decrease grain As concentrations. Husk amendment was likely effective at decreasing grain As and improving yield because it provided more plant-available Si, particularly during the reproductive and ripening phases. Both Husk and Ash provided K, which also played a role in yield improvement. This study demonstrates that while Si-rich amendments can affect rice uptake of As, the kinetics of Si dissolution and nutrient availability can also affect As uptake and toxicity in rice.

  17. LHCb RICH1 Engineering Design Review Report

    CERN Document Server

    Brook, N; Metlica, F; Muir, A; Phillips, A; Buckley, A; Gibson, V; Harrison, K; Jones, C R; Katvars, S G; Lazzeroni, C; Storey, J; Ward, CP; Wotton, S; Alemi, M; Arnabaldi, C; Bellunato, T F; Calvi, M; Matteuzzi, C; Musy, M; Negri, P; Perego, D L; Pessina, G; Chamonal, R; Eisenhardt, S; Lawrence, J; McCarron, J; Muheim, F; Playfer, S; Walker, A; Cuneo, S; Fontanelli, F; Gracco, Valerio; Mini, G; Musico, P; Petrolini, A; Sannino, M; Bates, A; MacGregor, A; O'Shea, V; Parkes, C; Paterson, S; Petrie, D; Pickford, A; Rahman, M; Soler, F; Allebone, L; Barber, J H; Cameron, W; Clark, D; Dornan, Peter John; Duane, A; Egede, U; Hallam, R; Howard, A; Plackett, R; Price, D; Savidge, T; Vidal-Sitjes, G; Websdale, D M; Adinolfi, M; Bibby, J H; Cioffi, C; Gligorov, Vladimir V; Harnew, N; Harris, F; McArthur, I A; Newby, C; Ottewell, B; Rademacker, J; Senanayake, R; Somerville, L P; Soroko, A; Smale, N J; Topp-Jørgensen, S; Wilkinson, G; Yang, S; Benayoun, M; Khmelnikov, V A; Obraztsov, V F; Densham, C J; Easo, S; Franek, B; Kuznetsov, G; Loveridge, P W; Morrow, D; Morris, JV; Papanestis, A; Patrick, G N; Woodward, M L; Aglieri-Rinella, G; Albrecht, A; Braem, André; Campbell, M; D'Ambrosio, C; Forty, R W; Frei, C; Gys, Thierry; Jamet, O; Kanaya, N; Losasso, M; Moritz, M; Patel, M; Piedigrossi, D; Snoeys, W; Ullaland, O; Van Lysebetten, A; Wyllie, K

    2005-01-01

    This document describes the concepts of the engineering design to be adopted for the upstream Ring Imaging Cherenkov detector (RICH1) of the reoptimized LHCb detector. Our aim is to ensure that coherent solutions for the engineering design and integration for all components of RICH1 are available, before proceeding with the detailed design of these components.

  18. Island Species Richness Increases with Habitat Diversity

    NARCIS (Netherlands)

    Hortal, J.; Triantis, K.A.; Meiri, S.; Thebault, E.M.C.; Sfenthourakis, S.

    2009-01-01

    Species richness is commonly thought to increase with habitat diversity. However, a recent theoretical model aiming to unify niche and island biogeography theories predicted a hump-shaped relationship between richness and habitat diversity. Given the contradiction between model results and previous

  19. Antibacterial biodegradable Mg-Ag alloys

    Directory of Open Access Journals (Sweden)

    D Tie

    2013-06-01

    Full Text Available The use of magnesium alloys as degradable metals for biomedical applications is a topic of ongoing research and the demand for multifunctional materials is increasing. Hence, binary Mg-Ag alloys were designed as implant materials to combine the favourable properties of magnesium with the well-known antibacterial property of silver. In this study, three Mg-Ag alloys, Mg2Ag, Mg4Ag and Mg6Ag that contain 1.87 %, 3.82 % and 6.00 % silver by weight, respectively, were cast and processed with solution (T4 and aging (T6 heat treatment.The metallurgical analysis and phase identification showed that all alloys contained Mg4Ag as the dominant β phase. After heat treatment, the mechanical properties of all Mg-Ag alloys were significantly improved and the corrosion rate was also significantly reduced, due to presence of silver. Mg(OH2 and MgO present the main magnesium corrosion products, while AgCl was found as the corresponding primary silver corrosion product. Immersion tests, under cell culture conditions, demonstrated that the silver content did not significantly shift the pH and magnesium ion release. In vitro tests, with both primary osteoblasts and cell lines (MG63, RAW 264.7, revealed that Mg-Ag alloys show negligible cytotoxicity and sound cytocompatibility. Antibacterial assays, performed in a dynamic bioreactor system, proved that the alloys reduce the viability of two common pathogenic bacteria, Staphylococcus aureus (DSMZ 20231 and Staphylococcus epidermidis (DSMZ 3269, and the results showed that the killing rate of the alloys against tested bacteria exceeded 90%. In summary, biodegradable Mg-Ag alloys are cytocompatible materials with adjustable mechanical and corrosion properties and show promising antibacterial activity, which indicates their potential as antibacterial biodegradable implant materials.

  20. Antinociceptive Activity of the Chloroform Fraction of Dioclea virgata (Rich. Amshoff (Fabaceae in Mice

    Directory of Open Access Journals (Sweden)

    Vanine Gomes Mota

    2011-01-01

    Full Text Available Acute treatment with the chloroform fraction of Dioclea virgata (Rich. Amshoff (CFDv in mice produced decreased ambulation and sedation in the behavioral pharmacological screening. Doses of 125 and 250 mg/kg CFDv decreased latency of sleep onset in the test of sleeping time potentiation. In the open field, animals treated with CFDv reduced ambulation and rearing (250 mg/kg, as well as defecation (125; 250 mg/kg. Regarding the antinociceptive activity, CFDv (125, 250, 500 mg/kg increased latency to first writhing and decreased the number of writhings induced by acetic acid. In the formalin test, CFDv (250 mg/kg decreased paw licking time in the first and second phases indicating antinociceptive activity that can be mediated both peripherally and at the central level. CFDv did not affect motor coordination until 120 minutes after treatment. CFDv shows psychopharmacological effects suggestive of CNS-depressant drugs with promising antinociceptive activity.

  1. Fertigation for improved water use efficiency and crop yield

    International Nuclear Information System (INIS)

    Al-Wabel, M.I.; Al-Jaloud, A.A.; Hussain, G.; Karimulla, S.

    2002-01-01

    A greenhouse experiment was carried out at the Al-Muzahmiya Research Station, King Abdulaziz City for Science and Technology, Riyadh, to evaluate the effect of fertigation on cucumber yield. Five labelled N ( 15 N) treatments namely a control, soil application (120 mg N L -1 ), N-1 (60 mg N L -1 ), N-2 (120 mg N L -1 ) and N-3 (180 mg N L -1 ) were tried for their effect on greenhouse cucumber yield. A cucumber cultivar (Figaro F-1) was sown as test crop. The experiment was carried out during the period from April to July, 1997. The mean fresh fruit cucumber yield ranged between 7.73 to 33.74 t ha -1 . Highest yield was obtained with the labelled N application of 180 mg L -1 . The mean ranges for the different elements in the plant leaves were 1.33- 2.70% (N), 0.364-0.515% (P) and 1.57-3.82% (K). Whereas, in the plant shoot these ranges were 1.26-2.42% (N), 0.28-0.49% (P) and 4.74-9.45% (K). The mean content of the different elements in the cucumber fruit was 2.15-3.70% (N), 0.47-0.73% (P) and 4.40-5.23% (K). The soil salinity varied between 2.23-4.66 dS m -1 in the top soil (0-20 cm depth) and 0.95-2.62 dS m -1 in the sub-surface (20-40 cm depth) soil. The application did not affect significantly the soil salinity and was found well below the hazardous limit for most crops. The evolution of the other elements was different.. For example, elements such as Ca, P and K showed an increase while Na showed a decrease, whereas the Mg content did not respond with increasing N application. The soil moisture ranged between 8.06-9.15% (0-20 cm depth) and 5.51-9.36% (20-40 cm depth) and did not show any effect of N application. The nitrogen use efficiency (NUE) varied between 72.70 to 129.53 kg kg -1 N in the different N treatments. The mean 15 N a.e. ranged from 0.010 to 0.844% (leaves), 0.058 to 0.855% (shoots), 0.044 to 0.747 (roots) and 0.07 to 0.823 % (fruits). In conclusion, the mean highest yield of cucumber as fresh fruit was 33.74 t ha -1 , obtained with 180 mg N L

  2. Effect of inter-row spacing and plant stand per hill on the yield of ...

    African Journals Online (AJOL)

    Yield was used to determined the best inter-row spacing and plant stand per bill ... high yieldlng cowpea Vigna unguicuJata lines at Serere Agricultural and Animal P.roduction .... constitute a rich source of adaptation to local conditions.

  3. Intra-individual comparison of different contrast media concentrations (300 mg, 370 mg and 400 mg iodine) in MDCT

    Energy Technology Data Exchange (ETDEWEB)

    Behrendt, Florian F.; Keil, Sebastian; Plumhans, Cedric; Guenther, Rolf W. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); Pietsch, Hubertus; Jost, Gregor; Sieber, Martin A.; Seidensticker, Peter [Bayer Schering Pharma AG, Berlin (Germany); Mahnken, Andreas H. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); RWTH Aachen University, Applied Medical Engineering, Helmholtz-Institute for Biomedical Engineering, Aachen (Germany)

    2010-07-15

    To compare intra-individual contrast enhancement in multi-detector-row computed tomography (MDCT) using contrast media (CM) containing 300, 370 and 400 mg iodine per ml (mgI/ml). Six pigs underwent repeated chest MDCT using three different CM (iopromide 300, iopromide 370, iomeprol 400). An identical iodine delivery (IDR) rate of 1.5 gI/s and a constant total iodine dose of 300 mg/kg body weight were used. Dynamic CT were acquired at the level of the pulmonary artery, and the ascending and descending aorta. After the time enhancement curves were computed, the pulmonary and aortic peak enhancement, time to peak and plateau time above 300 HU were calculated. Intra-individual peak contrast enhancement was significantly higher for the 300 mgI/ml contrast medium compared with the 370 and 400 mgI/ml media: pulmonary trunk 595 HU vs 516 HU (p = 0.0093) vs 472HU (p = 0.0005), and aorta 505 HU vs 454 HU (p = 0.0008) vs 439 HU (p = 0.0001), respectively. Comparison of time to peaks showed no significant difference. Plateau times were significantly longer for the 300 mgI/ml than for the 370 and 400 mgI/ml CM at all anatomical sites. Given normalised IDR and total iodine burden, the use of CM with a standard concentration with 300 mg iodine/ml provides improved contrast enhancement compared with highly concentrated CM in the chest. (orig.)

  4. Platelet-rich plasma in otolaryngology.

    Science.gov (United States)

    Stavrakas, M; Karkos, P D; Markou, K; Grigoriadis, N

    2016-12-01

    Platelet-rich plasma is a novel material that is being used more frequently in many surgical specialties. A literature review on the current and potential uses of platelet-rich plasma in otolaryngology was performed. There is limited evidence on the use of platelet-rich plasma in otolaryngology compared with other specialties: only 11 studies on various subspecialties (otology, rhinology and laryngology) were included in the final review. Based on the limited number of studies, we cannot draw safe conclusions about the value of platelet-rich plasma in otolaryngology. Nevertheless, the available literature suggests that platelet-rich plasma holds promise for future research and may have a number of clinical applications.

  5. Goodness of isospin in neutron rich systems from the fission fragment distribution

    Science.gov (United States)

    Garg, Swati; Jain, Ashok Kumar

    2017-09-01

    We present the results of our calculations for the relative yields of neutron-rich fission fragments emitted in 208Pb (18O, fission) reaction by using the concept of the conservation of isospin and compare with the experimental data. We take into account a range of isospin values allowed by the isospin algebra and assume that the fission fragments are formed in isobaric analog states. We also take into account the neutron multiplicity data for various neutron-emission channels in each partition, and use them to obtain the weight factors in calculating the yields. We then calculate the relative yields of the fission fragments. Our calculated results are able to reproduce the experimental trends reasonably well. This is the first direct evidence of the isospin conservation in neutron-rich systems and may prove a very useful tool in their studies.

  6. Yields of historical exploration programs

    International Nuclear Information System (INIS)

    Huslende, T.

    1995-01-01

    The paper relates to an method of evaluation developed for analysing the yield of historical exploration programs by computerized simulation. The most important elements show in coarse features how the results can be used in the different analyses. The evaluation is to be executed annually for the comparison and sorting of data from different offshore sites. Topics are exploration evaluation study, evaluation process, handling of exploration costs, discovered reserves, development projects, cash flow analysis, analysis of results, finding cost, international comparison. 1 ref., 11 figs

  7. Contribution of insect pollinators to crop yield and quality varies with agricultural intensification

    Directory of Open Access Journals (Sweden)

    Ignasi Bartomeus

    2014-03-01

    Full Text Available Background. Up to 75% of crop species benefit at least to some degree from animal pollination for fruit or seed set and yield. However, basic information on the level of pollinator dependence and pollinator contribution to yield is lacking for many crops. Even less is known about how insect pollination affects crop quality. Given that habitat loss and agricultural intensification are known to decrease pollinator richness and abundance, there is a need to assess the consequences for different components of crop production.Methods. We used pollination exclusion on flowers or inflorescences on a whole plant basis to assess the contribution of insect pollination to crop yield and quality in four flowering crops (spring oilseed rape, field bean, strawberry, and buckwheat located in four regions of Europe. For each crop, we recorded abundance and species richness of flower visiting insects in ten fields located along a gradient from simple to heterogeneous landscapes.Results. Insect pollination enhanced average crop yield between 18 and 71% depending on the crop. Yield quality was also enhanced in most crops. For instance, oilseed rape had higher oil and lower chlorophyll contents when adequately pollinated, the proportion of empty seeds decreased in buckwheat, and strawberries’ commercial grade improved; however, we did not find higher nitrogen content in open pollinated field beans. Complex landscapes had a higher overall species richness of wild pollinators across crops, but visitation rates were only higher in complex landscapes for some crops. On the contrary, the overall yield was consistently enhanced by higher visitation rates, but not by higher pollinator richness.Discussion. For the four crops in this study, there is clear benefit delivered by pollinators on yield quantity and/or quality, but it is not maximized under current agricultural intensification. Honeybees, the most abundant pollinator, might partially compensate the loss of wild

  8. Contribution of insect pollinators to crop yield and quality varies with agricultural intensification.

    Science.gov (United States)

    Bartomeus, Ignasi; Potts, Simon G; Steffan-Dewenter, Ingolf; Vaissière, Bernard E; Woyciechowski, Michal; Krewenka, Kristin M; Tscheulin, Thomas; Roberts, Stuart P M; Szentgyörgyi, Hajnalka; Westphal, Catrin; Bommarco, Riccardo

    2014-01-01

    Background. Up to 75% of crop species benefit at least to some degree from animal pollination for fruit or seed set and yield. However, basic information on the level of pollinator dependence and pollinator contribution to yield is lacking for many crops. Even less is known about how insect pollination affects crop quality. Given that habitat loss and agricultural intensification are known to decrease pollinator richness and abundance, there is a need to assess the consequences for different components of crop production. Methods. We used pollination exclusion on flowers or inflorescences on a whole plant basis to assess the contribution of insect pollination to crop yield and quality in four flowering crops (spring oilseed rape, field bean, strawberry, and buckwheat) located in four regions of Europe. For each crop, we recorded abundance and species richness of flower visiting insects in ten fields located along a gradient from simple to heterogeneous landscapes. Results. Insect pollination enhanced average crop yield between 18 and 71% depending on the crop. Yield quality was also enhanced in most crops. For instance, oilseed rape had higher oil and lower chlorophyll contents when adequately pollinated, the proportion of empty seeds decreased in buckwheat, and strawberries' commercial grade improved; however, we did not find higher nitrogen content in open pollinated field beans. Complex landscapes had a higher overall species richness of wild pollinators across crops, but visitation rates were only higher in complex landscapes for some crops. On the contrary, the overall yield was consistently enhanced by higher visitation rates, but not by higher pollinator richness. Discussion. For the four crops in this study, there is clear benefit delivered by pollinators on yield quantity and/or quality, but it is not maximized under current agricultural intensification. Honeybees, the most abundant pollinator, might partially compensate the loss of wild pollinators in

  9. Hydrogen insertion effects on the electronic structure of equiatomic MgNi traced by ab initio calculations

    Energy Technology Data Exchange (ETDEWEB)

    Matar, Samir F. [CNRS, ICMCB, UPR 9048, Pessac (France); Bordeaux Univ., Pessac (France). ICMCB, UPR 9048; Al Alam, Adel F.; Ouaini, Naim [Univ. Saint Esprit de Kaslik (USEK), Jounieh (Lebanon). URA GREVE, CSR-USEK

    2013-01-15

    For equiatomic MgNi which can be hydrogenated up to the composition MgNiH{sub 1.6} at an absorption/desorption temperature of 200 C, the effects of hydrogen absorption are approached with the model structures MgNiH, MgNiH{sub 2} and MgNiH{sub 3}. From full geometry optimization and calculated cohesive energies obtained within DFT, the MgNiH{sub 2} composition close to the experimental limit is identified as most stable. Charge density analysis shows an increasingly covalent character of hydrogen: MgNiH(H{sup -0.67}) {yields} MgNiH{sub 2}(H{sup -0.63}) {yields} MgNiH{sub 3}(H{sup -0.55}). While Mg-Ni bonding prevails in MgNi and hydrogenated model phases, extra itinerant low-energy Ni states appear when hydrogen is introduced signaling Ni-H bonding which prevails over Mg-H as evidenced from total energy calculations and chemical bonding analyses. (orig.)

  10. Behaviour of Fe4O5-Mg2Fe2O5 solid solutions and their relation to coexisting Mg-Fe silicates and oxide phases

    Science.gov (United States)

    Uenver-Thiele, Laura; Woodland, Alan B.; Miyajima, Nobuyoshi; Ballaran, Tiziana Boffa; Frost, Daniel J.

    2018-03-01

    Experiments at high pressures and temperatures were carried out (1) to investigate the crystal-chemical behaviour of Fe4O5-Mg2Fe2O5 solid solutions and (2) to explore the phase relations involving (Mg,Fe)2Fe2O5 (denoted as O5-phase) and Mg-Fe silicates. Multi-anvil experiments were performed at 11-20 GPa and 1100-1600 °C using different starting compositions including two that were Si-bearing. In Si-free experiments the O5-phase coexists with Fe2O3, hp-(Mg,Fe)Fe2O4, (Mg,Fe)3Fe4O9 or an unquenchable phase of different stoichiometry. Si-bearing experiments yielded phase assemblages consisting of the O5-phase together with olivine, wadsleyite or ringwoodite, majoritic garnet or Fe3+-bearing phase B. However, (Mg,Fe)2Fe2O5 does not incorporate Si. Electron microprobe analyses revealed that phase B incorporates significant amounts of Fe2+ and Fe3+ (at least 1.0 cations Fe per formula unit). Fe-L2,3-edge energy-loss near-edge structure spectra confirm the presence of ferric iron [Fe3+/Fetot = 0.41(4)] and indicate substitution according to the following charge-balanced exchange: [4]Si4+ + [6]Mg2+ = 2Fe3+. The ability to accommodate Fe2+ and Fe3+ makes this potential "water-storing" mineral interesting since such substitutions should enlarge its stability field. The thermodynamic properties of Mg2Fe2O5 have been refined, yielding H°1bar,298 = - 1981.5 kJ mol- 1. Solid solution is complete across the Fe4O5-Mg2Fe2O5 binary. Molar volume decreases essentially linearly with increasing Mg content, consistent with ideal mixing behaviour. The partitioning of Mg and Fe2+ with silicates indicates that (Mg,Fe)2Fe2O5 has a strong preference for Fe2+. Modelling of partitioning with olivine is consistent with the O5-phase exhibiting ideal mixing behaviour. Mg-Fe2+ partitioning between (Mg,Fe)2Fe2O5 and ringwoodite or wadsleyite is influenced by the presence of Fe3+ and OH incorporation in the silicate phases.

  11. High-Temperature Nucleosynthesis Processes on the Proton-Rich Side of Stability: the Alpha-Rich Freezeout and the rp^2-Process

    Science.gov (United States)

    Meyer, Bradley S.

    2001-10-01

    Nucleosynthesis on the proton-rich side of stability has at least two intriguing aspects. First, the most abundant of the stable iron-group isotopes, such as ^48Ti, ^52Cr, and ^56,57Fe, are synthesized as proton-rich, radioactive parents in alpha-rich freezeouts from equilibrium. The production of these radioactive progenitors depends in large measure on reactions on the proton-rich side of stability. The second intriguing aspect is that explosive nucleosynthesis in a hydrogen-rich environment (namely, the rp-process) may be associated with exotic astrophysical settings, such as x-ray bursts, and may be responsible for production of some of the light p-process nuclei (for example, ^92,94Mo and ^96,98Ru). We have developed web-based tools to help nuclear physicists determine which nuclear reactions on the proton-rich side of stability govern the nucleosynthesis in these processes. For the alpha-rich freezeout, one may determine the effect of any one of 2,140 reactions on the yield of any isotope in the nuclear reaction network with the web calculator. As a relevant example, I will discuss the governing role of ^57Ni (n,p)^57Co in the synthesis of the important astronomical observable ^57Co. As for explosive, proton-rich burning, I will discuss the synthesis of p-process nuclei in the repetitive rp-process (the rp^2-process). movies/rp.html>Movies of the rp^2-process illustrate its important features and give some indications of the important nuclear reactions.

  12. Crop diversity for yield increase.

    Directory of Open Access Journals (Sweden)

    Chengyun Li

    2009-11-01

    Full Text Available Traditional farming practices suggest that cultivation of a mixture of crop species in the same field through temporal and spatial management may be advantageous in boosting yields and preventing disease, but evidence from large-scale field testing is limited. Increasing crop diversity through intercropping addresses the problem of increasing land utilization and crop productivity. In collaboration with farmers and extension personnel, we tested intercropping of tobacco, maize, sugarcane, potato, wheat and broad bean--either by relay cropping or by mixing crop species based on differences in their heights, and practiced these patterns on 15,302 hectares in ten counties in Yunnan Province, China. The results of observation plots within these areas showed that some combinations increased crop yields for the same season between 33.2 and 84.7% and reached a land equivalent ratio (LER of between 1.31 and 1.84. This approach can be easily applied in developing countries, which is crucial in face of dwindling arable land and increasing food demand.

  13. The minimum yield in channeling

    International Nuclear Information System (INIS)

    Uguzzoni, A.; Gaertner, K.; Lulli, G.; Andersen, J.U.

    2000-01-01

    A first estimate of the minimum yield was obtained from Lindhard's theory, with the assumption of a statistical equilibrium in the transverse phase-space of channeled particles guided by a continuum axial potential. However, computer simulations have shown that this estimate should be corrected by a fairly large factor, C (approximately equal to 2.5), called the Barrett factor. We have shown earlier that the concept of a statistical equilibrium can be applied to understand this result, with the introduction of a constraint in phase-space due to planar channeling of axially channeled particles. Here we present an extended test of these ideas on the basis of computer simulation of the trajectories of 2 MeV α particles in Si. In particular, the gradual trend towards a full statistical equilibrium is studied. We also discuss the introduction of this modification of standard channeling theory into descriptions of the multiple scattering of channeled particles (dechanneling) by a master equation and show that the calculated minimum yields are in very good agreement with the results of a full computer simulation

  14. The Effects of Application Vinasseand additive nitrogen and phosphorus on Growth and Yield of Tomato

    Directory of Open Access Journals (Sweden)

    Ahmad Golchin

    2017-02-01

    Full Text Available Introduction:Vinasse is a byproduct of the sugar industry. Sugarcane or Sugarbeet is processed to produce crystallinesugar, pulp and molasses. The latter isfurther processed by fermentation to ethanol, ascorbicacid or other products. After the removal of the desired product (alcohol, ascorbicacid, etc. the remaining material is called vinasse. Vinasse is sold after a partial dehydration and usually has a viscositycomparable to molasses. Commercially offered vinasse comes either from sugarcaneand is called cane-vinasse or from sugarbeet and is called beet-vinasse. On average, for each liter of vinasse, 12 liters alcohol produced. Vinasse is a material with dark brown color and the smell of burned sugar, which is rich in potassium, calcium, magnesium, phosphorus and nitrogen. Materials and Methods:To determine the effect of vinasse and additive nitrogen and phosphorus on growth and yield of tomato, a factorial pot experiment was conducted at ZanjanUniversity in 2008. Two different plant nutrient including N and P and their combination (N+P were added to vinasse with three different concentrations to form experimental treatments. In addition to these treatments, three control treatments with vinasse of different concentrations, but with no additive were also included in the experiment. Each treatment used with two different application methods (soil application and soil + foliar application.The experiment had 24 treatments, a complete randomized design and three replications. The vinasse used in this experiment was diluted with water 10, 20 and 40 times to make a nutrient solution of three different concentrations of tomato plant. The amounts of nitrogen and phosphorus that were added to vinasse were 224 and 62 mg/l, respectively. Phosphorus and nitrogen were applied to as super-phosphate triple and calcium nitrate and ammonium nitrate respectively. After being deployed to ensure complete installation of tomatoes in pots containing perlite (about 2

  15. Production of high specific activity 27Mg by fast neutron irradiation and recoil-aided leaching

    International Nuclear Information System (INIS)

    Wierczinski, B.; Goeij, J.J.M. de; Volkers, K.J.

    2000-01-01

    High specific activity 27 Mg was produced via recoil-aided leaching from alumina in aqueous medium during irradiation with fast neutrons from a nuclear reactor. After irradiation the aqueous medium was passed through an IC-chelate column, the 24 Na formed during irradiation was removed by elution with 0.25 ml . l -1 sodium acetate and subsequently the 27 Mg was eluted with 2 mol . l -1 hydrochloric acid. Irradiation of alumina with a particle size of 3 μm and a specific surface area of 100 m 2 . g -1 in Milli-Q Plus Water yielded 90% of the total 27 Mg activity produced. Under standard conditions activities of about 8 . 10 5 Bq and specific activities of ca. 10 13 Bq . mol -1 were obtained at the end of irradiation. The standard working conditions involved irradiation of 200 mg alumina dispersed in 0.5 ml liquid in a fast neutron flux of 3 . 10 15 m -2 . s -1 for 15 min, a waiting time of 10 min, and a processing time of 15 minutes. Various alumina samples with different particle sizes and specific surfaces were tested, and the 27 Mg yields were fitted to a mathematical function. Since the high leaching yields cannot only be explained by recoil only, other phenomena such as diffusion and leaching aided by the high hydration energy of the Mg 2+ ion are probably involved. (orig.)

  16. Correlated O and Mg isotopic anomalies in Allende inclusions: II. Magnesium

    International Nuclear Information System (INIS)

    Wasserburg, G.J.; Lee, T.; Papanastassiou, D.A.

    1977-01-01

    Mg in two Allende Ca-Al rich inclusions shows large isotopic, mass-dependent fractionation which enriched the heavier isotopes. After normalization, Mg in these inclusions shows negative delta 26 Mg which appears to require the presence of nuclear effects in Mg distinct from 26 Al decay. The Mg mass fractionation is correlated with distinct but smaller fractionation effects for O reported by Clayton and Mayeda for the same inclusions (see companion paper). The observation of distinctive but uniform Mg isotopic composition in different phases within single Allende inclusions indicates that nuclear effects in O and Mg are not due to the entrapment of interstellar carrier grains as discrete entities, which are preserved as remnants, but are instead due to a homogenized mixture of components of extraordinary isotopic composition mixed with a component of ordinary solar system material and subjected to isotopic fractionation. The distinct O isotopic composition of different phases within a single inclusion is believed to be due to incomplete back-reaction of the higher temperature condensates with a cooler solar nebula of ''normal '' composition. The processes responsible for the O and Mg nuclear effects and the astrophysical site of their occurrence remain undefined

  17. New fundamental experimental studies on α-Mg(BH4)2 and other borohydrides

    International Nuclear Information System (INIS)

    Hagemann, Hans; D'Anna, Vincenza; Rapin, Jean-Philippe; Cerny, Radovan; Filinchuk, Yaroslav; Kim, Ki Chul; Sholl, David S.; Parker, Stewart F.

    2011-01-01

    Research highlights: → Eutectic behavior is observed in the LiBH4 -Mg(BH4)2 system. → New INS data show good agreement with theoretical DFT calculations. → Temperature dependent Raman spectra complement previous NMR studies. - Abstract: Several new studies of Mg(BH 4 ) 2 are reported. A 1:1 LiBH 4 :Mg(BH 4 ) 2 mixture was studied by in situ synchrotron X-ray diffraction and reveals an eutectic behavior with the eutectic composition more rich in Mg(BH 4 ) 2 , and the eutectic temperature lower than 456 K. No dual cation compound was observed in this experiment. New vibrational spectra including INS data have been obtained and are compared with theoretical DFT calculations and recent NMR studies, showing good agreement.

  18. New fundamental experimental studies on {alpha}-Mg(BH{sub 4}){sub 2} and other borohydrides

    Energy Technology Data Exchange (ETDEWEB)

    Hagemann, Hans, E-mail: Hans-Rudolf.Hagemann@unige.ch [Dept. de Chim. Phys, Univ. of Geneva (Switzerland); D' Anna, Vincenza [Dept. de Chim. Phys, Univ. of Geneva (Switzerland); Rapin, Jean-Philippe; Cerny, Radovan [Lab. Crystallography, Univ. of Geneva (Switzerland); Filinchuk, Yaroslav [Swiss-Norwegian Beam Lines at ESRF, Grenoble (France); Kim, Ki Chul; Sholl, David S. [School of Chemical and Biomolecular Engineering, Georgia Inst. Technol., Atlanta (United States); Parker, Stewart F. [ISIS Facility, STFC Rutherford Appleton Laboratory, Chilton, Didcot, Oxon OX11 0QX (United Kingdom)

    2011-09-15

    Research highlights: > Eutectic behavior is observed in the LiBH4 -Mg(BH4)2 system. > New INS data show good agreement with theoretical DFT calculations. > Temperature dependent Raman spectra complement previous NMR studies. - Abstract: Several new studies of Mg(BH{sub 4}){sub 2} are reported. A 1:1 LiBH{sub 4}:Mg(BH{sub 4}){sub 2} mixture was studied by in situ synchrotron X-ray diffraction and reveals an eutectic behavior with the eutectic composition more rich in Mg(BH{sub 4}){sub 2}, and the eutectic temperature lower than 456 K. No dual cation compound was observed in this experiment. New vibrational spectra including INS data have been obtained and are compared with theoretical DFT calculations and recent NMR studies, showing good agreement.

  19. Synthesis of glycerol carbonate by transesterification of glycerol with dimethyl carbonate over MgAl mixed oxide catalysts

    NARCIS (Netherlands)

    Liu, P.; Derchi, M.; Hensen, E.J.M.

    2013-01-01

    A series of hydrotalcite-like layered double hydroxides (LDHx) with different Mg/Al atomic ratios (x = 2–6) were prepared by using the co-precipitation method. Further calcination yields mixed oxides with tunable basicity. The basicity of the calcined LDHx (LDOx) strongly depends on the Mg/Al ratio

  20. The effect of the MgO buffer layer thickness on magnetic anisotropy in MgO/Fe/Cr/MgO buffer/MgO(001)

    Energy Technology Data Exchange (ETDEWEB)

    Kozioł-Rachwał, Anna, E-mail: a.koziolrachwal@aist.go.jp [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); Nozaki, Takayuki; Zayets, Vadym; Kubota, Hitoshi; Fukushima, Akio; Yuasa, Shinji [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Suzuki, Yoshishige [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)

    2016-08-28

    The relationship between the magnetic properties and MgO buffer layer thickness d was studied in epitaxial MgO/Fe(t)/Cr/MgO(d) layers grown on MgO(001) substrate in which the Fe thickness t ranged from 0.4 nm to 1.1 nm. For 0.4 nm ≤ t ≤ 0.7 nm, a non-monotonic coercivity dependence on the MgO buffer thickness was shown by perpendicular magneto-optic Kerr effect magnetometry. For thicker Fe films, an increase in the buffer layer thickness resulted in a spin reorientation transition from perpendicular to the in-plane magnetization direction. Possible origins of these unusual behaviors were discussed in terms of the suppression of carbon contamination at the Fe surface and changes in the magnetoelastic anisotropy in the system. These results illustrate a method to control magnetic anisotropy in MgO/Fe/Cr/MgO(d) via an appropriate choice of MgO buffer layer thickness d.

  1. Ultraviolet spectra of Mg in liquid helium

    International Nuclear Information System (INIS)

    Moriwaki, Y.; Morita, N.

    1999-01-01

    Emission and absorption spectra of Mg atoms implanted in liquid helium have been observed in the ultraviolet region. We have presented a model of exciplex formation of Mg-He 10 and found that this model is more suitable for understanding the dynamics in the 3s3p 1 P→3s 21 S transition than the bubble model. (orig.)

  2. Methane Emission and Milk Production of Dairy Cows Grazing Pastures Rich in Legumes or Rich in Grasses in Uruguay

    Directory of Open Access Journals (Sweden)

    Roberto Gratton

    2012-06-01

    Full Text Available Understanding the impact of changing pasture composition on reducing emissions of GHGs in dairy grazing systems is an important issue to mitigate climate change. The aim of this study was to estimate daily CH4 emissions of dairy cows grazing two mixed pastures with contrasting composition of grasses and legumes: L pasture with 60% legumes on Dry Matter (DM basis and G pasture with 75% grasses on DM basis. Milk production and CH4 emissions were compared over two periods of two weeks during spring using eight lactating Holstein cows in a 2 × 2 Latin square design. Herbage organic matter intake (HOMI was estimated by chromic oxide dilution and herbage organic matter digestibility (OMD was estimated by faecal index. Methane emission was estimated by using the sulfur hexafluoride (SF6 tracer technique adapted to collect breath samples over 5-day periods. OMD (0.71 and HOMI (15.7 kg OM were not affected by pasture composition. Milk production (20.3 kg/d, milk fat yield (742 g/d and milk protein yield (667 g/d were similar for both pastures. This may be explained by the high herbage allowance (30 kg DM above 5 cm/cow which allowed the cows to graze selectively, in particular in grass sward. Similarly, methane emission expressed as absolute value (368 g/d or 516 L/d or expressed as methane yield (6.6% of Gross Energy Intake (GEI was not affected by treatments. In conclusion, at high herbage allowance, the quality of the diet selected by grazing cows did not differ between pastures rich in legumes or rich in grasses, and therefore there was no effect on milk or methane production.

  3. Methane Emission and Milk Production of Dairy Cows Grazing Pastures Rich in Legumes or Rich in Grasses in Uruguay.

    Science.gov (United States)

    Dini, Yoana; Gere, José; Briano, Carolina; Manetti, Martin; Juliarena, Paula; Picasso, Valentin; Gratton, Roberto; Astigarraga, Laura

    2012-06-08

    Understanding the impact of changing pasture composition on reducing emissions of GHGs in dairy grazing systems is an important issue to mitigate climate change. The aim of this study was to estimate daily CH₄ emissions of dairy cows grazing two mixed pastures with contrasting composition of grasses and legumes: L pasture with 60% legumes on Dry Matter (DM) basis and G pasture with 75% grasses on DM basis. Milk production and CH₄ emissions were compared over two periods of two weeks during spring using eight lactating Holstein cows in a 2 × 2 Latin square design. Herbage organic matter intake (HOMI) was estimated by chromic oxide dilution and herbage organic matter digestibility (OMD) was estimated by faecal index. Methane emission was estimated by using the sulfur hexafluoride (SF6) tracer technique adapted to collect breath samples over 5-day periods. OMD (0.71) and HOMI (15.7 kg OM) were not affected by pasture composition. Milk production (20.3 kg/d), milk fat yield (742 g/d) and milk protein yield (667 g/d) were similar for both pastures. This may be explained by the high herbage allowance (30 kg DM above 5 cm/cow) which allowed the cows to graze selectively, in particular in grass sward. Similarly, methane emission expressed as absolute value (368 g/d or 516 L/d) or expressed as methane yield (6.6% of Gross Energy Intake (GEI)) was not affected by treatments. In conclusion, at high herbage allowance, the quality of the diet selected by grazing cows did not differ between pastures rich in legumes or rich in grasses, and therefore there was no effect on milk or methane production.

  4. Magnesium Isotopic Evidence for Ancient Subducted Oceanic Crust in LOMU-Like Potassium-Rich Volcanic Rocks

    Science.gov (United States)

    Sun, Yang; Teng, Fang-Zhen; Ying, Ji-Feng; Su, Ben-Xun; Hu, Yan; Fan, Qi-Cheng; Zhou, Xin-Hua

    2017-10-01

    To evaluate the role of subducted oceanic crust in the genesis of potassium-rich magmas, we report high-precision Mg isotopic data for a set of Cenozoic volcanic rocks from Northeast China. These rocks overall are lighter in Mg isotopic composition than the normal mantle and display considerable Mg isotopic variations, with δ26Mg ranging from -0.61 to -0.23. The covariation of δ26Mg with TiO2 in these rocks suggests that their light Mg isotopic compositions were derived from recycled oceanic crust in the form of carbonated eclogite in the source region. The strong correlations between δ26Mg and (Gd/Yb)N ratio as well as Sr-Pb isotopes further indicate a multicomponent and multistage origin of these rocks. Magnesium isotopes may thus be used as a novel tracer of recycled oceanic crust in the source region of mantle-derived magmas.

  5. Enhancing photocatalytic activity by using TiO2-MgO core-shell-structured nanoparticles

    International Nuclear Information System (INIS)

    Jung, Hyun Suk; Lee, Jung-Kun; Nastasi, Michael; Kim, Jeong-Ryeol; Lee, Sang-Wook; Kim, Jin Young; Park, Jong-Sung; Hong, Kug Sun; Shin, Hyunho

    2006-01-01

    Hygroscopic Mg(OH) 2 gel was topotactically decomposed on TiO 2 particle surfaces, resulting in highly nanoporous MgO-coated TiO 2 particles. The highly hygroscopic and nanoporous MgO shell absorbed more water molecules and hydroxyl groups from the environment to yield an improved photocatalytic property of the core-shell particles as compared to the uncoated TiO 2 counterpart

  6. Triglyceride-Rich Lipoproteins and Atherosclerotic Cardiovascular Disease: New Insights From Epidemiology, Genetics, and Biology.

    Science.gov (United States)

    Nordestgaard, Børge G

    2016-02-19

    Scientific interest in triglyceride-rich lipoproteins has fluctuated over the past many years, ranging from beliefs that these lipoproteins cause atherosclerotic cardiovascular disease (ASCVD) to being innocent bystanders. Correspondingly, clinical recommendations have fluctuated from a need to reduce levels to no advice on treatment. New insight in epidemiology now suggests that these lipoproteins, marked by high triglycerides, are strong and independent predictors of ASCVD and all-cause mortality, and that their cholesterol content or remnant cholesterol likewise are strong predictors of ASCVD. Of all adults, 27% have triglycerides >2 mmol/L (176 mg/dL), and 21% have remnant cholesterol >1 mmol/L (39 mg/dL). For individuals in the general population with nonfasting triglycerides of 6.6 mmol/L (580 mg/dL) compared with individuals with levels of 0.8 mmol/L (70 mg/dL), the risks were 5.1-fold for myocardial infarction, 3.2-fold for ischemic heart disease, 3.2-fold for ischemic stroke, and 2.2-fold for all-cause mortality. Also, genetic studies using the Mendelian randomization design, an approach that minimizes problems with confounding and reverse causation, now demonstrate that triglyceride-rich lipoproteins are causally associated with ASCVD and all-cause mortality. Finally, genetic evidence also demonstrates that high concentrations of triglyceride-rich lipoproteins are causally associated with low-grade inflammation. This suggests that an important part of inflammation in atherosclerosis and ASCVD is because of triglyceride-rich lipoprotein degradation and uptake into macrophage foam cells in the arterial intima. Taken together, new insights now strongly suggest that elevated triglyceride-rich lipoproteins represent causal risk factors for low-grade inflammation, ASCVD, and all-cause mortality. © 2016 American Heart Association, Inc.

  7. Neutron rich nuclei around 132Sn

    International Nuclear Information System (INIS)

    Bhattacharya, Sarmishtha

    2016-01-01

    The neutron rich nuclei with few particles or holes in 132 Sn have various experimental and theoretical interest to understand the evolution of nuclear structure around the doubly magic shell closure Z=50 and N=82. Some of the exotic neutron rich nuclei in this mass region are situated near waiting points in the r-process path and are of special astrophysical interest. Neutron rich nuclei near 132 Sn have been studied using fission fragment spectroscopy. The lifetime of low lying isomeric states have been precisely measured and the beta decay from the ground and isomeric states have been characterized using gamma-ray spectroscopy

  8. Firm size diversity, functional richness, and resilience

    Science.gov (United States)

    Garmestani, A.S.; Allen, Craig R.; Mittelstaedt, J.D.; Stow, C.A.; Ward, W.A.

    2006-01-01

    This paper applies recent advances in ecology to our understanding of firm development, sustainability, and economic development. The ecological literature indicates that the greater the functional richness of species in a system, the greater its resilience - that is, its ability to persist in the face of substantial changes in the environment. This paper focuses on the effects of functional richness across firm size on the ability of industries to survive in the face of economic change. Our results indicate that industries with a richness of industrial functions are more resilient to employment volatility. ?? 2006 Cambridge University Press.

  9. Positron annihilation study on the Fermi surface of Cd-Mg alloys

    International Nuclear Information System (INIS)

    Koike, Shu-ichi; Hirabayashi, Makoto; Suzuki, Toshiharu; Hasegawa, Masayuki.

    1979-01-01

    Angular correlation measurements of annihilation photons have been made on single crystals of the Cd-Mg alloys over all compositions. It is found that the Fermi surfaces of the alloys in the Cd-rich region distort considerably from a free-electron sphere; the 3rd band ''stars'' and the 4th band horizontal ''cigars'' around the points L do not exist in Cd, and appear at 10 at % Mg accompanying an appreciable decrease of the energy gap at L. It is proposed that changes in the 4d core states cause the sudden decrease of the energy gap. (author)

  10. Structural and mechanical properties of ZnMgO nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Tosun, M. [Istanbul Technical University, Faculty of Mechanical Engineering, 34437, Gumussuyu, Istanbul (Turkey); Ataoglu, S. [Istanbul Technical University, Faculty of Civil Engineering, 34469, Maslak, Istanbul (Turkey); Istanbul Technical University, Earthquake Engineering and Disaster Management Institute, 34469, Maslak, Istanbul (Turkey); Arda, L., E-mail: lutfi.arda@bahcesehir.edu.tr [Bahcesehir University, Faculty of Arts and Sciences, Department of Mathematics and Computer Sciences, Ciragan Cad, Osmanpasa Mektebi Sok, 34349, Besiktas, Istanbul (Turkey); Ozturk, O.; Asikuzun, E. [Kastamonu University, Faculty of Arts and Sciences, Department of Physics, 37100, Kastamonu (Turkey); Akcan, D. [Bahcesehir University, Faculty of Arts and Sciences, Department of Mathematics and Computer Sciences, Ciragan Cad, Osmanpasa Mektebi Sok, 34349, Besiktas, Istanbul (Turkey); Cakiroglu, O. [Hasan Ali Yucel Education Faculty, Istanbul University, 34452, Beyazit, Istanbul (Turkey)

    2014-01-10

    This study reports the effect of annealing temperature on the structure and mechanical properties of Zn{sub 0.95}Mg{sub 0.05}O bulk samples by using digital Vickers microhardness tester, X-ray diffraction analysis, scanning electron microscopy and electron dispersive X-ray measurements. The samples were prepared using Zn and Mg based alkoxed by the sol–gel technique and annealed at various temperatures (500, 600, 700 and 800 °C). Vickers microhardness, elastic modulus, yield strength and fracture toughness values of Zn{sub 0.95}Mg{sub 0.05}O bulk samples were separately calculated and compared with each other. The experimental results of hardness measurements were analyzed using Meyer's law, Proportional Specimen Resistance (PSR) and Elastic/Plastic Deformation (EPD) models and Hays–Kendall (HK) approach. Finally, it was seen that HK approach is the most successful model for the microhardness analysis of these materials.

  11. Broad range tuning of structural and optical properties of Znx Mg1−x O nanostructures grown by vapor transport method

    International Nuclear Information System (INIS)

    Vanjaria, Jignesh V; Azhar, Ebraheem Ali; Yu, Hongbin

    2016-01-01

    One-dimensional (1D) Zn x Mg 1−x O nanomaterials have drawn global attention due to their remarkable chemical and physical properties, and their diverse current and future technological applications. In this work, 1D ZnMgO nanostructures with different magnesium concentrations and different morphologies were grown directly on zinc oxide-coated silicon substrates by thermal evaporation of zinc oxide, magnesium boride and graphite powders. Highly well-defined Mg-rich ZnMgO nanorods with a rock salt structure and Zn-rich ZnMgO nanostructures with a wurtzite structure have been deposited individually by careful optimization of the source mixture and process parameters. Structural and optical properties of the deposited products were studied by scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, and Raman spectroscopy. Cathodoluminescence measurements demonstrate strong dominant peaks at 3.3 eV in Mg poor ZnMgO nanostructures and 4.8 eV in Mg rich nanostructures implying that the ZnMgO nanostructures can be used for the fabrication of deep UV optoelectronic devices. A mechanism for the formation and achieved diverse morphology of the ZnMgO nanostructures was proposed based on the characterization results. (paper)

  12. Electrochemical deposition of La-Mg alloys in LaCl3-MgCl2-KCl system with molten salt electrolysis process

    Directory of Open Access Journals (Sweden)

    Sahoo Kumar D.

    2014-01-01

    Full Text Available La-Mg alloys of different compositions were prepared by electrolysis of LaCl3-MgCl2-KCl melts. Different phases of La-Mg alloys were characterized by X-ray diffraction (XRD and Scanning Electron Microscopy (SEM. Energy dispersive spectrometry (EDS and Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES analyses showed that chemical compositions of La-Mg alloys were consistent with phase structures of XRD pattern, and magnesium content in the alloy could be controlled by electrolysis parameters. The effects of various process parameters such as concentration of magnesium chloride in the bath, temperature of electrolysis and cathode current density on the current efficiency have been investigated. A maximum current efficiency of 85% and yield of 80% was obtained from the bath at 12.5A/cm2 current density at an operating temp 850°C.

  13. Formkoexistenz in $^{32}$Mg: entdeckung des angeregten 0$^{+}$ zustands

    CERN Document Server

    Wimmer, Kathrin

    2010-01-01

    The evolution of shell structure in exotic nuclei as a function of proton (${Z}$) and neutron (${N}$) number is currently at the center of many theoretical and experimental investigations. It has been realized that the interaction of the last valence protons and neutrons, in particular the monopole component of the residual interaction between those nucleons, can lead to significant shifts in the single-particle energies, leading to the collapse of classic shell closures and the appearance of new shell gaps. The “Island of Inversion” around $^{32}$Mg, which is one of the most studied phenomena in the nuclear chart, is a well known example for such changes in nuclear structure. In this region of neutron-rich nuclei around the magic number${ N}$ = 20 strongly deformed ground states in Ne, Na, and Mg isotopes have been observed. Due to the reduction of the ${N}$ = 20 shell gap quadrupole correlations can enable low-lying deformed 2${p}$ − 2${h}$ intruder states from the ${fp}$-shell to compete with spheric...

  14. Steam gasification of rapeseed, wood, sewage sludge and miscanthus biochars for the production of a hydrogen-rich syngas

    International Nuclear Information System (INIS)

    Sattar, Anwar; Leeke, Gary A.; Hornung, Andreas; Wood, Joseph

    2014-01-01

    Steam gasification of biochars has emerged as a promising method for generating syngas that is rich in hydrogen. In this study four biochars formed via intermediate pyrolysis (wood pellet, sewage sludge, rapeseed and miscanthus) were gasified in a quartz tubular reactor using steam. The dynamic behaviour of the process and effects of temperature, steam flow and particle size were studied. The results show that increases in both steam flow and temperature significantly increase the dry gas yield and carbon conversion, but hydrogen volume fraction decreases at higher temperatures whilst particle size has little effect on gaseous composition. The highest volume fraction of hydrogen, 58.7%, was obtained at 750 °C from the rapeseed biochar. - Highlights: • Four biochars from intermediate pyrolysis were gasified. • High hydrogen concentration was achieved in all cases. • Peak hydrogen was 165 mg min −1  g −1 biochar at 700–750 °C. • High mineral content biochars had the highest reactivities. • Varying particle size had very little effect on gaseous composition

  15. Small-scale production in the Congo basin of low-acid carotene-rich red palm oil

    Directory of Open Access Journals (Sweden)

    Silou Thomas

    2017-09-01

    Full Text Available The red palm oil consumed in the Congo basin come essentially from small-scale production from the dura or tenera varieties (the latter being a hybrid of dura and pisifera. These three varieties are endemic to the Congo basin. The tenera variety is characterized a thick pulp (about 50% of the nut from which 70–90% of oil (based on fresh pulp can be extracted. The dura variety has less pulp (30% of the nut by weight, and gives an oil yield of the same order of magnitude. The oil is extracted from the crushed pulp after a series of mixing steps in hot water at about 60 °C. When obtained from freshly harvested nuts (at most 3 days storage, this oil is rich in carotenoids (800–2600 ppm and polyphenols (5–13 mg/g, and presents low acid values (IA < 5 and peroxide values (IP < 10. Here we describe this traditional production process, widespread in the Congo basin, and suggest innovations that substantially increase the quantity of oil extracted and significantly improve the quality of the end product.

  16. Obtaining anthocyanin-rich extracts from frozen açai (Euterpe oleracea Mart. pulp using pressurized liquid extraction

    Directory of Open Access Journals (Sweden)

    Sylvia Carolina ALCÁZAR-ALAY

    Full Text Available Abstract Açai is considered a functional food, and in addition to being a source of energy and fiber, it is a valuable source of bioactive compounds such as anthocyanins, minerals and fatty acids. In the present work, antioxidant-rich extracts from açai pulp were obtained using pressurized liquid extraction (PLE. The effects of the independent variables, including solvent type (pure ethanol and ethanol/water (50:50 v/v, citric acid (0 and 0.3%, w/w, pressure (20 and 80 bar and temperature (30 and 60 °C were evaluated using a full factorial design. The extraction was affected primarily by the solvent type and the citric acid percentage. The results indicate that the maximum overall yield (X0 was 64± 9 (%, d.b. when the process was performed using ethanol (99.5% and citric acid (0.3% w/w. The maximum total anthocyanin content and anthocyanin recovered from the raw material were 7 ± 1 (mg anthocyanin/g extract, d.b. and 11 ± 2 (%, d.b., respectively.

  17. Mg-spinel lithology: A new rock type on the lunar farside

    Science.gov (United States)

    Pieters, C.M.; Besse, S.; Boardman, J.; Buratti, B.; Cheek, L.; Clark, R.N.; Combe, J.-P.; Dhingra, D.; Goswami, J.N.; Green, R.O.; Head, J.W.; Isaacson, P.; Klima, R.; Kramer, G.; Lundeen, S.; Malaret, E.; McCord, T.; Mustard, J.; Nettles, J.; Petro, N.; Runyon, C.; Staid, M.; Sunshine, J.; Taylor, L.A.; Thaisen, K.; Tompkins, S.; Whitten, J.

    2011-01-01

    High-resolution compositional data from Moon Mineralogy Mapper (M 3) for the Moscoviense region on the lunar farside reveal three unusual, but distinctive, rock types along the inner basin ring. These are designated "OOS" since they are dominated by high concentrations of orthopyroxene, olivine, and Mg-rich spinel, respectively. The OOS occur as small areas, each a few kilometers in size, that are widely separated within the highly feldspathic setting of the basin rim. Although the abundance of plagioclase is not well constrained within the OOS, the mafic mineral content is exceptionally high, and two of the rock types could approach pyroxenite and harzburgite in composition. The third is a new rock type identified on the Moon that is dominated by Mg-rich spinel with no other mafic minerals detectable (lunar crust; they may thus be near contemporaneous with crustal products from the cooling magma ocean. Copyright ?? 2011 by the American Geophysical Union.

  18. Early-stage precipitation in Al-Zn-Mg-Cu alloy (7050)

    International Nuclear Information System (INIS)

    Sha Gang; Cerezo, Alfred

    2004-01-01

    GP zone and metastable η ' formation during the early-stage precipitation of a 7050 Al alloy aged at 121 deg. C has been investigated using transmission electron microscopy, together with 3-dimensional atom probe analysis (of the chemistry and morphology) of individual precipitates. Small Mg-rich clusters (GPI zones) are found in the alloy after short ageing times at 121 deg. C, together with larger GPI zones (Zn/Mg=1.0). Zn-rich η ' platelets are seen to form mainly between 30 and 240 min ageing, coexisting with larger GPI zones. A significant fraction of elongated clusters have also been observed over this period of ageing. The dominant mechanism for η ' formation at this stage is shown to be by transformation of small GPI zones, via these elongated clusters and not by nucleation on larger zones

  19. An Efficient, Solvent-Free Process for Synthesizing Anhydrous MgCl2

    Energy Technology Data Exchange (ETDEWEB)

    Motkuri, Radha K.; Vemuri, Venkata Rama S.; Barpaga, Dushyant; Schaef, Herbert T.; Loring, John S.; Martin, Paul F.; Lao, David; Nune, Satish K.; McGrail, Bernard P.

    2018-01-02

    A new efficient and solvent-free method for the synthesis of anhydrous MgCl2 from its hexahydrate is proposed. Fluidized dehydration of MgCl2·6H2O feedstock at 200 °C in a porous bed reactor yields MgCl2·nH2O (0 < n < 1), which has a similar diffraction pattern as activated MgCl2. The MgCl2·nH2O is then ammoniated directly using liquefied NH3 in the absence of solvent to form MgCl2·6NH3. Calcination of the hexammoniate complex at 300 °C then yields anhydrous MgCl2. Both dehydration and deammoniation were thoroughly studied using in situ as well as ex situ characterization techniques. Specifically, a detailed understanding of the dehydration process was monitored by in situ PXRD and in situ FTIR techniques where formation of salt with nH2O (n = 4, 2, 1, <1) was characterized. Given the reduction in thermal energy required to produce dehydrated feedstock with this method compared with current strategies, significant cost benefits are expected. Overall, the combined effect of activation, macroporosity, and coordinated water depletion allows the formation of hexammoniate without using solvent, thus minimizing waste formation.

  20. Influences of Gd on the microstructure and strength of Mg-4.5Zn alloy

    International Nuclear Information System (INIS)

    Yang Jie; Xiao Wenlong; Wang Lidong; Wu Yaoming; Wang Limin; Zhang Hongjie

    2008-01-01

    Microstructure and mechanical properties of peak-aged Mg-4.5Zn-xGd (x 0, 0.5, 1.0 and 1.5 wt.%) alloys have been investigated. The results showed that the grain size of the alloys was refined gradually with increasing Gd. Mg 5 Gd and Mg 3 Gd 2 Zn 3 phases were found in the Gd-containing alloys. The strengths were greatly improved with Gd additions, and the highest strength level was obtained in the Mg-4.5Zn-1.5Gd alloy, in which the ultimate tensile strength and yield strength were 231 MPa and 113 MPa, respectively. Through comparing with the Mg-4.5Zn alloy, the increments of ultimate tensile strength and yield strength were 22 MPa and 56 MPa, respectively. The improved strength was mainly correlated to the grain refining effect, the strengthening effect of the Mg 5 Gd and Mg 3 Gd 2 Zn 3 phases and also the hardening effect of the solutioned Gd atoms

  1. Effect of water regime and salinity on artichoke yield

    Directory of Open Access Journals (Sweden)

    Francesca Boari

    2012-03-01

    Full Text Available This work focuses on the effects of different salinity and water inputs on the yield of artichoke Violetto di Provenza. Two years of experimental works had been carried out in a site in Southern Italy characterized by semi-arid climate and deep loam soil. Three salinity levels of irrigation water (S0, S1 and S2 with electrical conductivity (ECw of 0.5, 5 and 10 dS m-1, respectively, were combined with three water regimes (W1, W2 and W3 corresponding in that order to 20 40 and 60% of available water depletion. The overall results of the salinity tolerance are in agreement with those from the literature. However, an higher tolerance to salinity was demonstrated when crop was watered more frequently (at 20% of available water depletion and a lower one when crop watering was performed less frequently (at 60% of available water depletion. The increase of salinity level reduced marketable yield (from 12.9 to 8.8 Mg ha-1, total heads (from 125,100 to 94,700 n ha-1 and heads mean weight (from 99.9 to 94.6 g, while increased heads dry matter (from 161.8 to 193.6 g kg-1 f.w. and reduced edible parte percentage of heads (from 35.2 to 33.2 %. Watering regimes, as average of the salinity levels, affected total heads marketable yield (115,350 n ha-1 and 11.4 Mg ha-1 for W1 and W2, 105,900 n ha-1 and 10 Mg ha-1 for W3. In addition, different watering regimes affected the secondary heads yield for which it was reduced by 3% of mean weight. The effect of different watering regimes changed with various salinity levels. In condition of moderate salinity (S1, maximum water depletion fraction to preserve heads number and weight yield was 40 and 20% of total soil available water, respectively. However, with high salinity (S2, maximum water depletion fraction to keep unchanged heads number and weight yield was 20% for both. The level of soil salinity at beginning of the crop cycle favoured the incidence of head atrophy in the main heads produced in the second year.

  2. Microstructures and mechanical properties of pure Mg processed by rotary swaging

    International Nuclear Information System (INIS)

    Gan, W.M.; Huang, Y.D.; Wang, R.; Wang, G.F.; Srinivasan, A.; Brokmeier, H.-G.; Schell, N.; Kainer, K.U.; Hort, N.

    2014-01-01

    Highlights: • Grain size of pure Mg can be effectively reduced by rotary swaging processing. • The dominated texture of the swaged pure Mg was a basal fibre. • Twinning and non-basal plane sliding accommodated the swaging process. • Gradient texture distribution was observed through the rod diameter. • There existed a slight shear deformation on the surface of the swaged rod. - Abstract: Microstructures and tensile properties of commercial pure magnesium processed by rotary swaging (RS) technique were investigated. Bulk and gradient textures in the RS processed Mg were characterised by neutron and synchrotron diffractions, respectively. Grains of the pure Mg were gradually refined with increase in the RS passes, which largely contributed to an increase in the tensile yield strength. A dominated basal fibre texture was observed in the RS processed pure Mg. Accommodated twinning deformation was also observed. Both the optical observations and texture analyses through the diameter of the swaged rod showed a gradient evolution in microstructure

  3. Ab-initio study of Mg-doped InN(0001 surface

    Directory of Open Access Journals (Sweden)

    A. Belabbes

    2013-01-01

    Full Text Available We study the incorporation of Mg atoms into the InN(0001 surface. Energies and atomic geometries are described within density functional theory, while the electronic structure is investigated by an approximate quasiparticle method that yields a gap value of 0.7 eV for bulk InN. The formation of substitutional Mg is energetically favored in the surface layer. The surface electronic structure is less influenced by Mg-derived states. The Fermi level is pinned by In-derived surface states. With increasing depth of Mg beneath the surface the Fermi-level position moves toward the valence band top, suggesting formation of holes and, hence, p-doping of Mg in bulk-like layers.

  4. Susceptibility testing for welding of AlMg alloys intended for extrusion

    Directory of Open Access Journals (Sweden)

    J. Borowski

    2016-07-01

    Full Text Available The objective of research was to determine the weldability, using Tungsten Inert Gas (TIG of extruded sections made of hard-deformable 5xxx series aluminum alloys with differing magnesium content, i.e. AlMg3, AlMg4,5, AlMg5, AlMg7. Welded joints were obtained as a result of a welding process consisting of several steps. Only welds characterized by very good appearance and quality were selected for tests. As a result of conducted research, TIG welding parameters were determined for sections with a thickness of 8 mm. It was observed that alloys of differing Mg content are characterized by high weldability and do not exhibit a significant reduction of the yield point. Moreover, joints exhibit uniform hardness distribution in the welded joint and heat-affected zone. Tensile strength is reduced.

  5. Comparing organic farming and land sparing: optimizing yield and butterfly populations at a landscape scale.

    Science.gov (United States)

    Hodgson, Jenny A; Kunin, William E; Thomas, Chris D; Benton, Tim G; Gabriel, Doreen

    2010-11-01

    Organic farming aims to be wildlife-friendly, but it may not benefit wildlife overall if much greater areas are needed to produce a given quantity of food. We measured the density and species richness of butterflies on organic farms, conventional farms and grassland nature reserves in 16 landscapes. Organic farms supported a higher density of butterflies than conventional farms, but a lower density than reserves. Using our data, we predict the optimal land-use strategy to maintain yield whilst maximizing butterfly abundance under different scenarios. Farming conventionally and sparing land as nature reserves is better for butterflies when the organic yield per hectare falls below 87% of conventional yield. However, if the spared land is simply extra field margins, organic farming is optimal whenever organic yields are over 35% of conventional yields. The optimal balance of land sparing and wildlife-friendly farming to maintain production and biodiversity will differ between landscapes. © 2010 Blackwell Publishing Ltd/CNRS.

  6. Optical absorption and thermoluminescence in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature

    International Nuclear Information System (INIS)

    Delgado, L.

    1984-01-01

    Optical absorption and thermoluminescence (TL) studies in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature are presented. In pure Mg O the thermal annihilation of Fe3+ by recombination with thermally released electrons at ∼ 90 and 175 degree centigree and the V center annealing by hole release up to 100 degree centigree cause the observed glow peaks at these temperatures. The TL excitation spectrum shows two maxima at 245 nm (electron center) and 288 nm (Fe3+). In Mg O:Ni X irradiation induces Fe 2 + →- Fe 3 + and Ni 2 + → Ni 3 + oxidations. Two TL emission bands centered at 110 degree centigree (red) and 80 o C (green) are assigned to electron release and their recombination at Fe 3 + and Ni 3 + respectively. In Mg O:Li two TL emission bands, one blue (430 nm) and the other red (730 nm) with excitation maxima at 245 nm (electron center) and 200 nm (hole center) respectively are observed. No V-center formation was detected in both Ni and Li doped samples. (Author) 42 refs

  7. Thermodynamics of neutron-rich nuclear matter

    Energy Technology Data Exchange (ETDEWEB)

    López, Jorge A., E-mail: jorgelopez@utep.edu [Department of Physics, University of Texas at El Paso, El Paso, Texas 79968, U.S.A (United States); Porras, Sergio Terrazas, E-mail: sterraza@uacj.mx; Gutiérrez, Araceli Rodríguez, E-mail: al104010@alumnos.uacj.mx [Universidad Autónoma de Ciudad Juárez, Ciudad Juárez, Chihuahua, México (Mexico)

    2016-07-07

    This manuscript presents methods to obtain properties of neutron-rich nuclear matter from classical molecular dynamics. Some of these are bulk properties of infinite nuclear matter, phase information, the Maxwell construction, spinodal lines and symmetry energy.

  8. Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

    Science.gov (United States)

    Kim, Il-Ho

    2018-05-01

    Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed

  9. Genesis of Cenozoic intraplate high Mg# andesites in Northeast China

    Science.gov (United States)

    Liu, J. Q.; Chen, L. H.; Zhong, Y.; Wang, X. J.

    2017-12-01

    High-Mg# andesites (HMAs) are usually generated in the converged plate boundary and have genetic relationships with slab subduction. However, it still remained controversial about the origin of those HMAs erupted in the intra-plate setting. Here we present major, trace element, and Sr-Nd-Pb-Hf isotopic compositions for the Cenozoic intra-plate HMAs from Northeast China to constrain their origin and formation process. Cenozoic Xunke volcanic rocks are located in the northern Lesser Khingan Range, covering an area of about 3, 000 km2. These volcanic rocks are mainly basaltic andesite and basaltic trachyandesite, with only several classified as trachyandesite and andesites. They have high SiO2 contents (54.3-57.4 wt%) and Mg# (49.6-57.8), falling into the scope of high Mg# andesites. The Xunke HMAs are enriched in large ion lithophile elements but depleted in high field strength elements, with positive Ba, K, Sr and negative Zr-Hf, and Ti anomalies. Their trace element absolute concentrations are between those of potassic basalts and Wuchagou HMAs. The Xunke HMAs have relatively enriched Sr-Nd-Hf isotopes (87Sr/86Sr = 0.705398-0.705764, ɛNd=-8.8-3.8, ɛHf=0.5-11.7), and low radiogenic Pb isotopes (206Pb/204Pb = 16.701-17.198), towards to the EM1 end-member, which indicates that they are ultimately derived from ancient, recycled crustal components. Primitive silica-rich melts were generated from higher degrees of partial melting of recycled crustal materials (relative to potassic basalts) and then interacted with the peridotite to produce the Xunke HMAs.

  10. Yield and Quality Traits of some Rice Mutant Lines as Affected by Different Nitrogen Levels

    International Nuclear Information System (INIS)

    Sobieh, S.El-S.S.

    2007-01-01

    Two field experiments were carried out during two growing seasons (2004 and 2005) at a farm located in Sahafa village, Sharkia Governorate, to evaluate newly rice mutants comparing with the local cultivar Sakha 104 for yield and quality characteristics as affected by nitrogen fertilizer levels. The obtained results showed that: 1- Rice grain yield and yield attributes were significantly increased with increasing N levels from 23 to 69 kg N fed '. 2- Both mutant MG 16 and MS 6 exhibited highly significant increases in mean values for yield attributes except for number of panicles/m2, as compared with the local cultivar Sakha 104. 3- Percentage of yield increases were 26.85 and 16.21 % for mutant MG16 and MS6 comparing with the local variety Sakha 104, respectively. Mutant MG 16 showed the highest mean values for plant height, panicle length, number of grains per panicle, panicle weight, 1000-grain weight, grain yield/fed, and straw yield/fed, as compared with the mutant MS 6 and Sakha 104. 4- Hulling and milling % were significantly increased as increasing of nitrogen levels from 23 to 69 kg N fed 1 , whereas head rice, gel consistency and amylose content were not significantly affect. 5- Significant differences were obtained between the three rice genotypes for hulling %, milling %, head rice %, amylose content and gel consistency

  11. Leveraging data rich environments using marketing analytics

    OpenAIRE

    Holtrop, Niels

    2017-01-01

    With the onset of what is popularly known as “big data”, increased attention is being paid to creating value from these data rich environments. Within the field of marketing, the analysis of customer and market data supported by models is known as marketing analytics. The goal of these analyses is to enhance managerial decision making regarding marketing problems. However, before these data rich environments can be used to guide managerial decision making, firms need to grasp the process of d...

  12. Hydrogen-rich gas production by cogasification of coal and biomass in an intermittent fluidized bed.

    Science.gov (United States)

    Wang, Li-Qun; Chen, Zhao-Sheng

    2013-01-01

    This paper presents the experimental results of cogasification of coal and biomass in an intermittent fluidized bed reactor, aiming to investigate the influences of operation parameters such as gasification temperature (T), steam to biomass mass ratio (SBMR), and biomass to coal mass ratio (BCMR) on hydrogen-rich (H2-rich) gas production. The results show that H2-rich gas free of N2 dilution is produced and the H2 yield is in the range of 18.25~68.13 g/kg. The increases of T, SBMR, and BCMR are all favorable for promoting the H2 production. Higher temperature contributes to higher CO and H2 contents, as well as H2 yield. The BCMR has a weak influence on gas composition, but the yield and content of H2 increase with BCMR, reaching a peak at the BCMR of 4. The H2 content and yield in the product gas increase with SBMR, whilst the content of CO increases first and then decreases correspondingly. At a typical case, the relative linear sensitivity coefficients of H2 production efficiency to T, SBMR, and BCMR were calculated. The results reveal that the order of the influence of the operation parameters on H2 production efficiency is T > SBMR > BCMR.

  13. Improving magnetic properties of MgB{sub 2} bulk superconductors by synthetic engine oil treatment

    Energy Technology Data Exchange (ETDEWEB)

    Taylan Koparan, E., E-mail: etaylan20@gmail.com [Department of Science Education, Eregli Faculty of Education, Bulent Ecevit University, TR-67300, Zonguldak (Turkey); Savaskan, B. [Energy Systems Engineering, Faculty of Technology, Karadeniz Technical University, 61830, Of, Trabzon (Turkey); Yanmaz, E. [Department of Mechatronics, Faculty of Engineering and Architecture, İstanbul Gelişim University, İstanbul (Turkey)

    2016-08-15

    Highlights: • The effects of synthetic engine oil treatment on magnetic properties of bulk MgB{sub 2} superconductors has been first time investigated and reported. • Synthetic engine oil used as a product which is cheap and a rich carbon source obviously has improved the superconducting magnetic properties of MgB{sub 2}. • The critical current density of all of MgB{sub 2} samples immersed at different standby time in engine oil in whole field range has been better than that of the pure MgB{sub 2} sample. • The MgB{sub 2} sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. - Abstract: The present study focuses on the effects of standby time of the MgB{sub 2} samples immersed in synthetic engine oil on the critical current density ( J{sub c}(H)), magnetic field dependence of the pinning force density f{sub p}(b) and T{sub c} performances of MgB{sub 2} bulk superconductors. Synthetic engine oil was used as a product which is cheap and a rich carbon source. Manufactured MgB{sub 2} pellet samples were immersed at different standby time of 30 min, 120 min, 300 min and 1440 min in synthetic engine oil after the first heating process. Finally, MgB{sub 2} samples immersed in synthetic engine oil were sintered at 1000 °C and kept for 15 min in Ar atmosphere. The critical current density of all of MgB{sub 2} samples immersed at different standby time in engine oil in whole field range was better than that of the pure MgB{sub 2} sample because of the number of the pinning centers. The MgB{sub 2} sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. The J{sub c} value for the pure sample is 2.0 × 10{sup 3} A/cm{sup 2}, whereas for the MgB{sub 2} sample immersed at 300 min standby time in engine oil the J{sub c} is enhanced to 4.8 × 10{sup 3} A/cm{sup 2} at 5 K and 3 T. The superconducting transition temperature (T{sub c}) did not change

  14. Improving magnetic properties of MgB_2 bulk superconductors by synthetic engine oil treatment

    International Nuclear Information System (INIS)

    Taylan Koparan, E.; Savaskan, B.; Yanmaz, E.

    2016-01-01

    Highlights: • The effects of synthetic engine oil treatment on magnetic properties of bulk MgB_2 superconductors has been first time investigated and reported. • Synthetic engine oil used as a product which is cheap and a rich carbon source obviously has improved the superconducting magnetic properties of MgB_2. • The critical current density of all of MgB_2 samples immersed at different standby time in engine oil in whole field range has been better than that of the pure MgB_2 sample. • The MgB_2 sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. - Abstract: The present study focuses on the effects of standby time of the MgB_2 samples immersed in synthetic engine oil on the critical current density ( J_c(H)), magnetic field dependence of the pinning force density f_p(b) and T_c performances of MgB_2 bulk superconductors. Synthetic engine oil was used as a product which is cheap and a rich carbon source. Manufactured MgB_2 pellet samples were immersed at different standby time of 30 min, 120 min, 300 min and 1440 min in synthetic engine oil after the first heating process. Finally, MgB_2 samples immersed in synthetic engine oil were sintered at 1000 °C and kept for 15 min in Ar atmosphere. The critical current density of all of MgB_2 samples immersed at different standby time in engine oil in whole field range was better than that of the pure MgB_2 sample because of the number of the pinning centers. The MgB_2 sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. The J_c value for the pure sample is 2.0 × 10"3 A/cm"2, whereas for the MgB_2 sample immersed at 300 min standby time in engine oil the J_c is enhanced to 4.8 × 10"3 A/cm"2 at 5 K and 3 T. The superconducting transition temperature (T_c) did not change with the increasing standby time of the samples in synthetic engine oil at all. The best diamagnetic property was

  15. Phase boundary between cubic B1 and rhombohedral structures in (Mg,Fe)O magnesiowüstite determined by in situ X-ray diffraction measurements

    Science.gov (United States)

    Dymshits, Anna M.; Litasov, Konstantin D.; Shatskiy, Anton; Chanyshev, Artem D.; Podborodnikov, Ivan V.; Higo, Yuji

    2018-01-01

    The phase relations and equation of state of (Mg0.08Fe0.92)O magnesiowüstite (Mw92) have been studied using the Kawai-type high-pressure apparatus coupled with synchrotron radiation. To determine the phase boundary between the NaCl-type cubic (B1) and rhombohedral ( rB1) structures in Mw92, in situ X-ray observations were carried out at pressures of 0-35 GPa and temperatures of 300-1473 K. Au and MgO were used as the internal pressure markers and metallic Fe as oxygen fugacity buffer. The phase boundary between B1 and rB1 structures was described by a linear equation P (GPa) = 1.6 + 0.033 × T (K). The Clapeyron slope (d P/d T) determined in this study is close to that obtained at pressures above 70 GPa but steeper than that obtained for FeO. An addition of MgO to FeO structure expands the stability field of the rB1 phase to lower pressures and higher temperatures. Thus, the rB1 phase may be stabilized with respect to the B1 phase at a lower pressures. The pressure-volume-temperature equation of state of B1-Mw92 was determined up to 30 GPa and 1473 K. Fitting the hydrostatic compression data up to 30 GPa with the Birch-Murnaghan equation of state (EoS) yielded: unit cell volume ( V 0, T0), 79.23 ± 4 Å3; bulk modulus ( K 0, T0), 183 ± 4 GPa; its pressure derivative ( K' T ), 4.1 ± 0.4; (∂ K 0, T /∂ T) = -0.029 ± 0.005 GPa K‒1; a = 3.70 ± 0.27 × 10-5 K-1 and b = 0.47 ± 0.49 × 10-8 K-2, where α0, T = a + bT is the volumetric thermal expansion coefficient. The obtained bulk modulus of Mw92 is very close to the value expected for stoichiometric iron-rich (Mg,Fe)O. This result confirms the idea that the bulk modulus of (Mg,Fe)O is greatly affected by the actual defect structure, caused by either Mg2+ or vacancies.

  16. Preparation of nanocrystalline MgO by surfactant assisted precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, Mehran, E-mail: rezaei@kashanu.ac.ir [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of); Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan (Iran, Islamic Republic of); Khajenoori, Majid; Nematollahi, Behzad [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of)

    2011-10-15

    Highlights: {yields} Nanocrystalline magnesium oxide with high surface area. {yields} MgO prepared with surfactant showed different morphologies compared with the sample prepared without surfactant. {yields} MgO prepared with surfactant showed a plate-like shape. {yields} Refluxing temperature and time and the surfactant to metal molar ratio affect the textural properties of MgO. -- Abstract: Nanocrystalline magnesium oxide with high surface area was prepared by a simple precipitation method using pluronic P123 triblock copolymer (Poly (ethylene glycol)-block, Poly (propylene glycol)-block, Poly (ethylene glycol)) as surfactant and under refluxing conditions. The prepared samples were characterized by X-ray diffraction (XRD), N{sub 2} adsorption (BET) and scanning and transmission electron microscopies (SEM and TEM). The obtained results revealed that the refluxing time and temperature and the molar ratio of surfactant to metal affect the structural properties of MgO, because of the changes in the rate and extent of P123 adsorption on the prepared samples. The results showed that the addition of surfactant is effective to prepare magnesium oxide with high surface area and affects the morphology of the prepared samples. With increasing the P123/MgO molar ratio to 0.05 the pore size distribution was shifted to larger size. The sample prepared with addition of surfactant showed a plate-like shape which was completely different with the morphology of the sample prepared without surfactant. The formation of nanoplate-like MgO was related to higher surface density of Mg ions on the (0 0 1) plane than that on the other planes of the Mg(OH){sub 2} crystal. The (0 0 1) plane would be blocked preferentially by the adsorbed P123 molecules during the growing process of Mg(OH){sub 2} nanoentities and the growth on the (0 0 1) plane would be markedly restricted, and the consequence is the generation of nanoplate-like MgO. In addition, increase in refluxing temperature and time

  17. Superconductivity in MgB{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Muranaka, Takahiro; Akimitsu, Jun [Aoyama Gakuin Univ., Kanagawa (Japan). Dept. of Physics and Mathematics

    2011-07-01

    We review superconductivity in MgB{sub 2} in terms of crystal and electronic structure, electron-phonon coupling, two-gap superconductivity and application. Finally, we introduce the development of new superconducting materials in related compounds. (orig.)

  18. Additive Manufacturing of Magnesium (Mg) Alloys

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed work is to investigate additive manufacturing techniques for Mg alloys.  It will leverage off research being conducted at University of Florida and...

  19. Yield trends and yield gap analysis of major crops in the world

    NARCIS (Netherlands)

    Hengsdijk, H.; Langeveld, J.W.A.

    2009-01-01

    This study aims to quantify the gap between current and potential yields of major crops in the world, and the production constraints that contribute to this yield gap. Using an expert-based evaluation of yield gaps and the literature, global and regional yields and yield trends of major crops are

  20. The intergranular corrosion behavior of 6000-series alloys with different Mg/Si and Cu content

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Yun; Liu, Qing, E-mail: qingliu@cqu.edu.cn; Jia, Zhihong, E-mail: zhihongjia@cqu.edu.cn; Xing, Yuan; Ding, Lipeng; Wang, Xueli

    2017-05-31

    Highlights: • High Cu alloy with high Mg/Si ratio has the best comprehensive property. • Addition of excess Mg could improve the intergranular corrosion resistance. • Si containing particles on the grain boundaries of Si-rich alloys promote IGC. • IGC susceptibility depends primarily on Cu content and secondarily on Mg/Si ratio. - Abstract: 6000-series aluminium alloys with high Cu or excess Si addition were susceptible to intergranular corrosion (IGC). In order to obtain good IGC resistance, four alloys with low/high Cu and various Mg/Si ratios were designed. The corrosion behaviour of four alloys was investigated by accelerated corrosion test, electrochemical test and electron microscopies. It was revealed that IGC susceptibility of alloys was the result of microgalvanic coupling between the noble grain boundary precipitates and the adjacent precipitates free zone (PFZ), which was closely related to a combination of Cu content and the Mg/Si ratio. Excess Mg could improve the IGC resistance of alloys by forming discontinuous precipitates on the grain boundaries. The designed alloy with high Cu and excess Mg has the same corrosion level as the commercial alloy with low Cu and excess Si, which provides possibility for developing new alloy.

  1. Preparation and characterisation of Os doped MgB{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Grivel, J.-C., E-mail: jean@dtu.dk; Namazkar, S.; Alexiou, A.; Holte, O.J.

    2014-12-15

    Highlights: • Polycrystalline osmium doped MgB{sub 2} samples were prepared by solid state route. • Up to 1 at.% Mg can be replaced by Os in the MgB{sub 2} lattice. • T{sub c} decreases at a rate of 2.1 K/at.% Os upon doping. - Abstract: Polycrystalline samples with Mg{sub 1−x}Os{sub x}B{sub 2.04} nominal stoichiometry were made by reacting elemental powders at 800 °C under argon atmosphere. Based on XRD diffraction patterns, EDS analysis and magnetisation measurements, it is found that Os can replace up to about 1 at.% Mg in the MgB{sub 2} lattice. Beyond this doping level, unreacted Os and Mg-rich Mg–Os impurity phases are formed. The a-axis parameter contracts upon doping while the superconducting transition temperature decreases at a rate of 2.1 K/at.% Os substitution. At 10 K, Os doping induces an improvement of the normalised critical current density under applied magnetic fields in excess of 0.5 T, indicating a modest enhancement of flux pinning in this range.

  2. Band gap tuning of ZnO nanoparticles via Mg doping by femtosecond laser ablation in liquid environment

    International Nuclear Information System (INIS)

    Chelnokov, E.; Rivoal, M.; Colignon, Y.; Gachet, D.; Bekere, L.; Thibaudau, F.; Giorgio, S.; Khodorkovsky, V.; Marine, W.

    2012-01-01

    Highlights: ► Femtosecond laser ablation synthesis of Mg doped ZnO nanoparticles. ► Electronic properties of ZnO are modified by Mg. ► Band gap and exciton energy shifts to the blue. ► The exciton energy shift is saturated at Mg content of about 20%. ► Phase separation at Mg content is at more than 25%. ► Mechanism of exciton pinning – recombination via new surface states. - Abstract: We use multiphoton IR femtosecond laser ablation to induce non-thermal non-equilibrium conditions of the nanoparticle growth in liquids. Modifications of the electronic properties of ZnO NP were achieved by Mg ion doping of targets prepared from mixtures of Zn and Mg acetylacetonates. The nanoparticle sizes were 3–20 nm depending on the ablation conditions. X-ray fluorescence indicates that stoichiometric ablation and incorporation of Mg in nanocrystalline ZnO occurs. HRTEM observations show that nanoparticles retain their wurtzite structure, while at high Mg concentrations we detect the MgO rich domains. Exciton emissions exhibit relatively narrow bands with progressive and controlled blue shifts up to 184 meV. The exciton energy correlates to band edge absorption indicating strong modification of the NP band gaps. Stabilisation of the exciton blue shift is observed at high Mg concentration. It is accompanied by the formation of structure defects and ZnO/MgO phase separation within the nanoparticles.

  3. Effect of Different Silicon Sources on Yield and Silicon Uptake of Rice Grown under Varying Phosphorus Rates

    Directory of Open Access Journals (Sweden)

    Flavia B. Agostinho

    2017-08-01

    Full Text Available A series of pot experiments were conducted to: (1 evaluate the effects of different Si sources (soil- and foliar-applied on grain yield and Si accumulation of rice supplied with varying P rates, and (2 evaluate Si absorption of rice using foliar- and soil-applied Si fertilizers. Three P rates, (0, 112, and 224 kg ha−1 combined with five Si treatments (wollastonite and slag applied at 4.5 ton ha−1 and one foliar Si solution applied at 20, 40 and 80 mg Si L−1 and a check were arranged in a randomized complete block design with four replications. The presence of P and Si in the soil created a synergistic effect on soil Al, Mn, and As (P < 0.01, but not on rice growth and P uptake. Wollastonite and slag application were most effective in raising rice Si content than foliar applied Si (P < 0.001. While there was an improvement in biomass (42% and tiller production (25% for rice receiving foliar Si, no supporting evidence was obtained in these experiments to verify leaf surface Si absorption. The application of Si-rich materials to soil still remains the most effective method for enhancing Si uptake by plants.

  4. Effect of Different Silicon Sources on Yield and Silicon Uptake of Rice Grown under Varying Phosphorus Rates.

    Science.gov (United States)

    Agostinho, Flavia B; Tubana, Brenda S; Martins, Murilo S; Datnoff, Lawrence E

    2017-08-29

    A series of pot experiments were conducted to: (1) evaluate the effects of different Si sources (soil- and foliar-applied) on grain yield and Si accumulation of rice supplied with varying P rates, and (2) evaluate Si absorption of rice using foliar- and soil-applied Si fertilizers. Three P rates, (0, 112, and 224 kg ha -1 ) combined with five Si treatments (wollastonite and slag applied at 4.5 ton ha -1 and one foliar Si solution applied at 20, 40 and 80 mg Si L -1 ) and a check were arranged in a randomized complete block design with four replications. The presence of P and Si in the soil created a synergistic effect on soil Al, Mn, and As ( P rice growth and P uptake. Wollastonite and slag application were most effective in raising rice Si content than foliar applied Si ( P production (25%) for rice receiving foliar Si, no supporting evidence was obtained in these experiments to verify leaf surface Si absorption. The application of Si-rich materials to soil still remains the most effective method for enhancing Si uptake by plants.

  5. Effects of organic fertilizers on soil physicochemistry and on the yield and botanical composition of forage over 3 years.

    Science.gov (United States)

    Matos-Moreira, Mariana; López-Mosquera, M Elvira; Cunha, Mario; Sáinz Osés, María Jesús; Rodríguez, Teresa; Carral, Emilio V

    2011-07-01

    Organic wastes have been reported to reduce saturation of the exchange complex by Al in Al-rich acid soils. For 3 years, the main soil fertility properties were studied in plots sown with mixed pasture species. These plots were fertilized with cattle slurry, dairy sludge (DS), or granulated broiler litter (BL) in comparison with mineral fertilizer. Al saturation levels were low after the initial inorganic liming treatment (19.00-33.71%) but tended to rise under all treatments (21.09-61.37%) except BL (8.45-30.98%), which was also associated with the highest average soil pH and the highest average levels of exchangeable Ca2+, Mg2+, and K+. Treatment DS performed similarly to mineral fertilizer in most respects, but it led to greater available P levels. Under the dry conditions of the second and third years of the study, BL and DS treatments were associated with significantly greater forage yields than the other treatments. Under DS treatment, available P levels were too low to allow the maintenance of mixed pasture, clover being eliminated by the less P-dependent species.

  6. Using biomass of starch-rich transgenic Arabidopsis vacuolar as feedstock for fermentative hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Lo, Yung-Chung; Cheng, Chieh-Lun; Chen, Chun-Yen [National Cheng Kung Univ., Tainan, Taiwan (China). Dept. of Chemical Engineering; Huang, Li-Fen; Chang, Jo-Shu [Yuan Ze Univ., Tao-yuan, Taiwan (China). Graduate School of Biotechnology and Bioengineering

    2010-07-01

    Cellulose is the major constitute of plant biomass and highly available in agricultural wastes and industrial effluents, thereby being a cost-effective feedstock for bioenergy production. However, most hydrogen producing bacteria (HPB) could not directly convert cellulosic materials (such as rice husk and rice straw) into hydrogen whereas most HPB could utilize sugar and starch for hydrogen production. In this work, we used an indigenous bacterial isolate Clostridium butyricum CGS2 as HPB, which could directly convert soluble starch into H2 with a maximum H2 production rate and a H2 yield of 205.07 ml H2/h/l and 6.46 mmol H2/g starch, respectively. However, C. butyricum CGS2 could not ferment pure cellulosic materials such as carboxymethyl cellulose and xylan. Moreover, we found that C. butyricum CGS2 could utilize rich husk to produce H2 at a rate of 13.19 ml H2/h/l due to the starch content in rice husk (H2 yield = 1.49 mmol H2/g rice husk). In contrast, since lacking starch content, rice straw cannot be converted to H2 by C. butyricum CGS2. The foregoing results suggest that increasing the starch content in the natural agricultural wastes may make them better feedstock for fermentative H2 production. Hence, a genetically modified plant (Arabidopsis vacuolar) was constructed to enhance its starch concentration. The starch concentration of mutant plant S1 increased to 10.67 mg/fresh weight, which is four times higher than that of wild type plant. Using mutant plant S1 as carbon source, C. butyricum CGS2 was able to give a high cumulative H2 production and H2 production rate of 285.4 ml H2/l and 43.6 ml/h/l, respectively. The cumulative H2 production and H2 production rate both increased when the concentration of the transgenic plant was increased. Therefore, this study successful demonstrated the feasibility of expressing starch on genetically-modified plants to create a more effective feedstock for dark H2 fermentation. (orig.)

  7. Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation.

    Science.gov (United States)

    Martinez Sanchez, Adela H; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J C

    2017-03-01

    Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10wt% of gadolinium (Mg-10Gd) and Mg with 2wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Mg/Ca of Continental Ostracode Shells

    Science.gov (United States)

    Ito, E.; Forester, R. M.; Marco-Barba, J.; Mezquita, F.

    2007-12-01

    Marine ionic chemistry is thought to remain constant. This, together with the belief that marine calcifiers partition Mg/Ca in a systematic manner as functions of temperature (and Mg/Ca) of water forms the basis of the Mg/Ca thermometer. In continental settings both of these assumptions are usually not true. Continental waters contain a wide variety of solutes in absolute and relative ion concentrations. Hence, waters with identical Mg/Ca may have very different concentrations of Mg and Ca and very different anions. Here we use two examples to focus on the effects of ion chemistry on Mg/Ca partitioning in continental ostracode shells and we ignore the complexities of solute evolution, which can change Mg/Ca over timescales of minutes to millennia. Palacios-Fest and Dettman (2001) conducted a monthly study of ,Cypridopsis vidua at El Yeso Lake in Sonora, Mexico. They established a relation between temperature and average shell Mg/Ca using regression analyses on averaged data. When their Mg/Ca-temperature relation is applied to monthly ,C. vidua data from Page Pond near Cleveland, Ohio, water temperatures of -8 to -1°C are obtained. The observed Mg/Ca ranges for El Yeso Lake (0.31 to 0.46) and Page Pond (0.33 to 0.46) are similar, as are their specific conductivities (700 to 850μS for El Yeso Lake; 400 to 600μS for Page Pond). However, [Ca] is 140-260 mg/L for El Yeso, but only 70-90 mg/L for Page Pond. Page Pond data, in fact, shows a good temperature shell Mg/Ca relation for .C. vidua, but the relation is different from that at El Yeso. Hence, shell Mg/Ca is a multi-valued, family of curves function of temperature and Mg/Ca of water that depends on the [Mg] and [Ca] values in water and perhaps other factors. Our second example comes from sites near Valencia, Spain and involves shell data for ,Cyprideis torosa, an estuarine ostracode that is tolerant of a wide range of salinity and can live in continental waters as long as the carbonate alkalinity to Ca ratio is

  9. Prussian Blue Mg-Li Hybrid Batteries.

    Science.gov (United States)

    Sun, Xiaoqi; Duffort, Victor; Nazar, Linda F

    2016-08-01

    The major advantage of Mg batteries relies on their promise of employing an Mg metal negative electrode, which offers much higher energy density compared to graphitic carbon. However, the strong coulombic interaction of Mg 2+ ions with anions leads to their sluggish diffusion in the solid state, which along with a high desolvation energy, hinders the development of positive electrode materials. To circumvent this limitation, Mg metal negative electrodes can be used in hybrid systems by coupling an Li + insertion cathode through a dual salt electrolyte. Two "high voltage" Prussian blue analogues (average 2.3 V vs Mg/Mg 2+ ; 3.0 V vs Li/Li + ) are investigated as cathode materials and the influence of structural water is shown. Their electrochemical profiles, presenting two voltage plateaus, are explained based on the two unique Fe bonding environments. Structural water has a beneficial impact on the cell voltage. Capacities of 125 mAh g -1 are obtained at a current density of 10 mA g -1 (≈C/10), while stable performance up to 300 cycles is demonstrated at 200 mA g -1 (≈2C). The hybrid cell design is a step toward building a safe and high density energy storage system.

  10. Arsenic rich iron plaque on macrophyte roots - an ecotoxicological risk?

    International Nuclear Information System (INIS)

    Taggart, M.A.; Mateo, R.; Charnock, J.M.; Bahrami, F.; Green, A.J.; Meharg, A.A.

    2009-01-01

    Arsenic is known to accumulate with iron plaque on macrophyte roots. Three to four years after the Aznalcollar mine spill (Spain), residual arsenic contamination left in seasonal wetland habitats has been identified in this form by scanning electron microscopy. Total digestion has determined arsenic concentrations in thoroughly washed 'root + plaque' material in excess of 1000 mg kg -1 , and further analysis using X-ray absorption spectroscopy suggests arsenic exists as both arsenate and arsenite. Certain herbivorous species feed on rhizomes and bulbs of macrophytes in a wide range of global environments, and the ecotoxicological impact of consuming arsenic rich iron plaque associated with such food items remains to be quantified. Here, greylag geese which feed on Scirpus maritimus rhizome and bulb material in areas affected by the Aznalcollar spill are shown to have elevated levels of arsenic in their feces, which may originate from arsenic rich iron plaque. - Accumulation of metals with iron plaque on macrophyte roots in wetlands poses an ecotoxicological risk to certain herbivores

  11. Arsenic rich iron plaque on macrophyte roots - an ecotoxicological risk?

    Energy Technology Data Exchange (ETDEWEB)

    Taggart, M.A. [School of Biological Sciences, University of Aberdeen, Cruickshank Bld, St Machar Drive, Aberdeen, AB24 3UU (United Kingdom); Instituto de Investigacion en Recursos Cinegeticos, IREC (CSIC-UCLM-JCCM), Ronda de Toledo s/n, 13005 Ciudad Real (Spain)], E-mail: mark.taggart@uclm.es; Mateo, R. [Instituto de Investigacion en Recursos Cinegeticos, IREC (CSIC-UCLM-JCCM), Ronda de Toledo s/n, 13005 Ciudad Real (Spain); Charnock, J.M.; Bahrami, F. [Synchrotron Radiation Department, CCLRC Daresbury Laboratory, Warrington, Cheshire, WA4 4AD (United Kingdom); Green, A.J. [Department of Wetland Ecology, Estacion Biologica de Donana, CSIC, Pabellon del Peru, Avenida Maria Luisa s/n, 41013 Seville (Spain); Meharg, A.A. [School of Biological Sciences, University of Aberdeen, Cruickshank Bld, St Machar Drive, Aberdeen, AB24 3UU (United Kingdom)

    2009-03-15

    Arsenic is known to accumulate with iron plaque on macrophyte roots. Three to four years after the Aznalcollar mine spill (Spain), residual arsenic contamination left in seasonal wetland habitats has been identified in this form by scanning electron microscopy. Total digestion has determined arsenic concentrations in thoroughly washed 'root + plaque' material in excess of 1000 mg kg{sup -1}, and further analysis using X-ray absorption spectroscopy suggests arsenic exists as both arsenate and arsenite. Certain herbivorous species feed on rhizomes and bulbs of macrophytes in a wide range of global environments, and the ecotoxicological impact of consuming arsenic rich iron plaque associated with such food items remains to be quantified. Here, greylag geese which feed on Scirpus maritimus rhizome and bulb material in areas affected by the Aznalcollar spill are shown to have elevated levels of arsenic in their feces, which may originate from arsenic rich iron plaque. - Accumulation of metals with iron plaque on macrophyte roots in wetlands poses an ecotoxicological risk to certain herbivores.

  12. GDP growth and the yield curvature

    DEFF Research Database (Denmark)

    Møller, Stig Vinther

    2014-01-01

    This paper examines the forecastability of GDP growth using information from the term structure of yields. In contrast to previous studies, the paper shows that the curvature of the yield curve contributes with much more forecasting power than the slope of yield curve. The yield curvature also...... predicts bond returns, implying a common element to time-variation in expected bond returns and expected GDP growth....

  13. Applications of pressurized cation exchange chromatography for fission yield determination

    International Nuclear Information System (INIS)

    Yan Shuheng; Lin Fa; Zhang Hongdi; Li Xueliang; Zhang Shulan

    1988-01-01

    In order to determine the fission yields of lanthanides precisely, lanthanides with carriers of 1-2 mg per element are separated from each other by means of pressurized cation exchange chromatography - αHIBA concentration gradient elution. The effect of initial loading technique, concentration gradient, flow rate, and temperature on separation were investigated in detail. Under the optimum conditions adapted according to the results given in this work, all the lanthanides can be completely separated within about 90 minutes with a recovery of more than 95% and purity higher than 99%. (author) 3 refs.; 6 figs

  14. Biodegradation of Mg-14Li alloy in simulated body fluid: A proof-of-concept study

    Directory of Open Access Journals (Sweden)

    Xiao-Bo Chen

    2018-03-01

    Full Text Available High corrosion kinetics and localised corrosion progress are the primary concerns arising from the clinical implementation of magnesium (Mg based implantable devices. In this study, a binary Mg-lithium (Li alloy consisting a record high Li content of 14% (in weight was employed as model material aiming to yield homogenous and slow corrosion behaviour in a simulated body fluid, i.e. minimum essential medium (MEM, in comparison to that of generic Mg alloy AZ31 and biocompatible Mg-0.5Zn-0.5Ca counterparts. Scanning electron microscopy examination reveals single-phase microstructural characteristics of Mg-14Li (β-Li, whilst the presence of insoluble phases, cathodic to α-Mg matrix, in AZ31 and Mg-0.5Zn-0.5Ca. Though slight differences exist in the corrosion kinetics of all the specimens over a short-term time scale (no longer than 60 min, as indicated by potentiodynamic polarisation and electrochemical impedance spectroscopy, profound variations are apparent in terms of immersion tests, i.e. mass loss and hydrogen evolution measurements (up to 7 days. Cross-sectional micrographs unveil severe pitting corrosion in AZ31 and Mg-0.5Zn-0.5Ca, but not the case for Mg-14Li. X-ray diffraction patterns and X-ray photoelectron spectroscopy confirm that a compact film (25 μm in thickness consisting of lithium carbonate (Li2CO3 and calcium hydroxide was generated on the surface of Mg-14Li in MEM, which contributes greatly to its low corrosion rate. It is proposed therefore that the single-phase structure and formation of protective and defect-free Li2CO3 film give rise to the controlled and homogenous corrosion behaviour of Mg-14Li in MEM, providing new insights for the exploration of biodegradable Mg materials.

  15. Formation and Corrosion Resistance of Mg-Al Hydrotalcite Film on Mg-Gd-Zn Alloy

    Science.gov (United States)

    Ba, Z. X.; Dong, Q. S.; Kong, S. X.; Zhang, X. B.; Xue, Y. J.; Chen, Y. J.

    2017-06-01

    An environment-friendly technique for depositing a Mg-Al hydrotalcite (HT) (Mg6Al2(OH)16-CO3ṡ4H2O) conversion film was developed to protect the Mg-Gd-Zn alloy from corrosion. The morphology and chemical compositions of the film were analyzed by scanning electronic microscope (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and Raman spectroscopy (RS), respectively. The electrochemical test and hydrogen evolution test were employed to evaluate the biocorrosion behavior of Mg-Gd-Zn alloy coated with the Mg-Al HT film in the simulated body fluid (SBF). It was found that the formation of Mg-Al HT film was a transition from amorphous precursor to a crystalline HT structure. The HT film can effectively improve the corrosion resistance of magnesium alloy. It indicates that the process provides a promising approach to modify Mg-Gd-Zn alloy.

  16. Reaction mechanism for the symmetric breakup of 24Mg following an interaction with 12C

    International Nuclear Information System (INIS)

    Gyapong, G.J.; Watson, D.L.; Catford, W.N.; Clarke, N.M.; Bennett, S.J.; Freer, M.; Fulton, B.R.; Jones, C.D.; Leddy, M.; Murgatroyd, J.T.; Rae, W.D.M.; Simmons, P.

    1994-01-01

    Data on the yield of the symmetric breakup of 24 Mg as a function of beam energy are presented and compared with detailed calculations of the energy dependence. The 24 Mg states seen in symmetric breakup agree with previously observed breakup states having spin and parities J π =4 + ,(6 + ),8 + . The data allow the variations of yield for indivual states to be judged, as the beam energy is varied. The variation in the yield of the 4 + states is compared in detail with calculations assuming several possible compound nuclear or direct reaction mechanisms. It is concluded that a massive ( 12 C) transfer or a simple statistical compound process are unlikely mechanisms, but that each of several other mechanisms is consistent with the data. ((orig.))

  17. Analysis of yield advantage in mixed cropping

    NARCIS (Netherlands)

    Ranganathan, R.

    1993-01-01

    It has long been recognized that mixed cropping can give yield advantages over sole cropping, but methods that can identify such yield benefits are still being developed. This thesis presents a method that combines physiological and economic principles in the evaluation of yield advantage.

  18. Fission yield data evaluation system FYDES

    International Nuclear Information System (INIS)

    Liu Tingjin

    1998-01-01

    Taking account of some features of fission yield data, to do the fission yield data evaluation conveniently, a fission yield data evaluation system FYDES has been developed for last two years. Outline of the system, data retrieval and data table standardization, data correction codes, data averaging code, simultaneous evaluation code and data fit programs were introduced

  19. modelling relationship between rainfall variability and yields

    African Journals Online (AJOL)

    , S. and ... factors to rice yield. Adebayo and Adebayo (1997) developed double log multiple regression model to predict rice yield in Adamawa State, Nigeria. The general form of .... the second are the crop yield/values for millet and sorghum ...

  20. LITHIUM-RICH GIANTS IN GLOBULAR CLUSTERS

    Energy Technology Data Exchange (ETDEWEB)

    Kirby, Evan N.; Cohen, Judith G. [California Institute of Technology, 1200 E. California Boulevard, MC 249-17, Pasadena, CA 91125 (United States); Guhathakurta, Puragra [UCO/Lick Observatory and Department of Astronomy and Astrophysics, University of California, 1156 High Street, Santa Cruz, CA 95064 (United States); Zhang, Andrew J. [The Harker School, 500 Saratoga Avenue, San Jose, CA 95129 (United States); Hong, Jerry [Palo Alto High School, 50 Embarcadero Road, Palo Alto, CA, 94301 (United States); Guo, Michelle [Stanford University, 450 Serra Mall, Stanford, CA 94305 (United States); Guo, Rachel [Irvington High School, 41800 Blacow Road, Fremont, CA 94538 (United States); Cunha, Katia [Observatório Nacional, São Cristóvão Rio de Janeiro (Brazil)

    2016-03-10

    Although red giants deplete lithium on their surfaces, some giants are Li-rich. Intermediate-mass asymptotic giant branch (AGB) stars can generate Li through the Cameron–Fowler conveyor, but the existence of Li-rich, low-mass red giant branch (RGB) stars is puzzling. Globular clusters are the best sites to examine this phenomenon because it is straightforward to determine membership in the cluster and to identify the evolutionary state of each star. In 72 hours of Keck/DEIMOS exposures in 25 clusters, we found four Li-rich RGB and two Li-rich AGB stars. There were 1696 RGB and 125 AGB stars with measurements or upper limits consistent with normal abundances of Li. Hence, the frequency of Li-richness in globular clusters is (0.2 ± 0.1)% for the RGB, (1.6 ± 1.1)% for the AGB, and (0.3 ± 0.1)% for all giants. Because the Li-rich RGB stars are on the lower RGB, Li self-generation mechanisms proposed to occur at the luminosity function bump or He core flash cannot explain these four lower RGB stars. We propose the following origin for Li enrichment: (1) All luminous giants experience a brief phase of Li enrichment at the He core flash. (2) All post-RGB stars with binary companions on the lower RGB will engage in mass transfer. This scenario predicts that 0.1% of lower RGB stars will appear Li-rich due to mass transfer from a recently Li-enhanced companion. This frequency is at the lower end of our confidence interval.

  1. Effect of fertilisation on biomass yield, ash and element uptake in SRC willow

    DEFF Research Database (Denmark)

    Ugilt Larsen, Søren; Jørgensen, Uffe; Kjeldsen, Jens Bonderup

    2016-01-01

    +0, 2) NPK120+0, 3) Slurry180+0, 4) NPK120+120, 5) NPK240+0, 6) Slurry360+0. Fertilization affected biomass yield significantly but interacted with rotation and clone. In first rotation, fertilization increased dry matter (DM) yield across clones significantly from 3.7 Mg ha−1 y−1 for Control0+0 to 6.......5, 6.4 and 5.6 for Slurry360+0, NPK120+120 and NPK240+0, respectively. In second rotation, yield increased from 6.2 Mg ha−1 y−1 to 8.8, 8.2, 7.8 and 7.4 for Slurry360+0, NPK240+0, Slurry180+0 and NPK120+120, respectively. Biomass dry matter yield per ha increased linearly at 15 kg kg−1 of applied total...

  2. Cover Crops Effects on Soil Chemical Properties and Onion Yield

    Directory of Open Access Journals (Sweden)

    Rodolfo Assis de Oliveira

    2016-01-01

    Full Text Available ABSTRACT Cover crops contribute to nutrient cycling and may improve soil chemical properties and, consequently, increase crop yield. The aim of this study was to evaluate cover crop residue decomposition and nutrient release, and the effects of these plants on soil chemical properties and on onion (Allium cepa L. yield in a no-tillage system. The experiment was carried out in an Inceptisol in southern Brazil, where cover crops were sown in April 2012 and 2013. In July 2013, shoots of weeds (WD, black oats (BO, rye (RY, oilseed radish (RD, oilseed radish + black oats (RD + BO, and oilseed radish + rye (RD + RY were cut at ground level and part of these material from each treatment was placed in litter bags. The litter bags were distributed on the soil surface and were collected at 0, 30, 45, 60, 75, and 90 days after distribution (DAD. The residues in the litter bags were dried, weighed, and ground, and then analyzed to quantify lignin, cellulose, non-structural biomass, total organic carbon (TOC, N, P, K, Ca, and Mg. In November 2012 and 2013, onion crops were harvested to quantify yield, and bulbs were classified according to diameter, and the number of rotted and flowering bulbs was determined. Soil in the 0.00-0.10 m layer was collected for chemical analysis before transplanting and after harvesting onion in December 2012 and 2013. The rye plant residues presented the highest half-life and they released less nutrients until 90 DAD. The great permanence of rye residue was considered a protection to soil surface, the opposite was observed with spontaneous vegetation. The cultivation and addition of dry residue of cover crops increased the onion yield at 2.5 Mg ha-1.

  3. Melting relations in the MgO-MgSiO3 system up to 70 GPa

    Science.gov (United States)

    Ohnishi, Satoka; Kuwayama, Yasuhiro; Inoue, Toru

    2017-06-01

    Melting experiments in a binary system MgO-MgSiO3 were performed up to 70 GPa using a CO2 laser heated diamond anvil cell. The quenched samples were polished and analyzed by a dualbeam focused ion beam (FIB) and a field emission scanning electron microscope (FE-SEM), respectively. The liquidus phase and the eutectic composition were determined on the basis of textual and chemical analyses of sample cross sections. Our experimental results show that the eutectic composition is the Si/Mg molar ratio of 0.76 at 35 GPa and it decreases with increasing pressure. Above 45 GPa, it becomes relatively constant at about 0.64-0.65 Si/Mg molar ratio. Using our experimental data collected at a wide pressure range up to 70 GPa together with previous experimental data, we have constructed a thermodynamic model of the eutectic composition of the MgO-MgSiO3 system. The eutectic composition extrapolated to the pressure and temperature conditions at the base of the mantle is about 0.64 Si/Mg molar ratio. The modeled eutectic composition is quite consistent with a previous prediction from ab initio calculations (de Koker et al. in Earth Planet Sci Lett 361:58-63, 2013), suggesting that the simple assumption of a non-ideal regular solution model can well describe the melting relation of the MgO-MgSiO3 system at high pressure. Our results show that the liquidus phase changes from MgO-periclase to MgSiO3-bridgmanite at 35 GPa for the simplified pyrolite composition ( 0.7 Si/Mg molar ratio), while MgSiO3-bridgmanite is the liquidus phase at the entire lower mantle conditions for the chondritic composition ( 0.84 Si/Mg molar ratio).

  4. Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

    Energy Technology Data Exchange (ETDEWEB)

    Martinez Sanchez, Adela H., E-mail: adela.martinez@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany); Weinberg, Annelie [Department of Orthopedics and Orthopedic Surgery, Medical University of Graz (Austria); Luthringer, Bérengère J.C. [Helmholtz-Zentrum Geesthacht, Institute of Material Research, Department for Structural Research on Macromolecules, Geesthacht (Germany)

    2017-03-01

    Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

  5. Chondrogenic differentiation of ATDC5-cells under the influence of Mg and Mg alloy degradation

    International Nuclear Information System (INIS)

    Martinez Sanchez, Adela H.; Feyerabend, Frank; Laipple, Daniel; Willumeit-Römer, Regine; Weinberg, Annelie; Luthringer, Bérengère J.C.

    2017-01-01

    Biodegradable magnesium (Mg)-based materials are a potential alternative to permanent implants for application in children. Nevertheless effects of those materials on growth plate cartilage and chondrogenesis have not been previously evaluated. In vitro differentiation of ATDC5 cells was evaluated under the influence of pure Mg (PMg), Mg with 10 wt% of gadolinium (Mg-10Gd) and Mg with 2 wt% of silver (Mg-2Ag) degradation products (extracts) and direct cell culture on the materials. Gene expression showed an inhibitory effect on ATDC5 mineralization with the three extracts and a chondrogenic potential of Mg-10Gd. Cells cultured in Mg-10Gd and Mg-2Ag extracts showed the same proliferation and morphology than cells cultured in growth conditions. Mg-10Gd induced an increase in production of ECM and a bigger cell size, similar to the effects found with differentiation conditions. An increased metabolic activity was observed in cells cultured under the influence of Mg-10Gd extracts, indicated by an acidic pH during most of the culture period. After 7 days of culture on the materials, ATDC5 growth, distribution and ECM synthesis were higher on Mg-10Gd samples, followed by Mg-2Ag and PMg, which was influenced by the homogeneity and composition of the degradation layer. This study confirmed the tolerance of ATDC5 cells to Mg-based materials and a chondrogenic effect of Mg-10Gd. Further studies in vitro and in vivo are necessary to evaluate cell reactions to those materials, as well as the effects on bone growth and the biocompatibility of the alloying system in the body. - Highlights: • Degradation of PMg, and Mg-2Ag do not influence ATDC5 cells growth and chondrogenic redifferentiation. • Mg-10Gd enhances fast chondrogenic redifferentiation and expression of hyperthrophic markers on ATDC5 cells. • Further evaluation of the effects of PMg, Mg-10Gd and Mg-2Ag in vivo are necessary to confirm its potential for application in growing bones.

  6. The Effectiveness of Al-Si Coatings for Preventing Interfacial Reaction in Al - Mg Dissimilar Metal Welding

    OpenAIRE

    Wang, Yin; Al-Zubaidy, Basem; Prangnell, Philip

    2017-01-01

    The dissimilar welding of aluminum to magnesium is challenging because of the rapid formation of brittle intermetallic compounds (IMC) at the weld interface. An Al-Si coating interlayer was selected to address this problem, based on thermodynamic calculations that predicted silicon would change the reaction path to avoid formation of the normally observed binary Al-Mg IMC phases (-Al3Mg2 and -Al12Mg17). Long-term static heat treatments confirmed that a Si-rich coating will preferentially pr...

  7. Thermal stability and creep behaviour of MgNiYCe-rich mischmetal alloys processed by a powder metallurgy route

    Czech Academy of Sciences Publication Activity Database

    Peréz, P.; Milička, Karel; Badia, J. M.; Garcés, G.; Antoranz, J. M.; Gonzáles, S.; Dobeš, Ferdinand; Adeva, P.

    289-292, - (2009), s. 127-136 ISSN 1012-0386. [DIMAT 2008, International Conference on Diffusion in Materials /7./. Lanzarote, Canary Islands, 28.10.2008-31.10.2008] Grant - others:Ministerio de Ciencia y Tecnologia (ES) MAT2006-11731-C02 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * powder metallurgy * microstructure * thermal stability * creep Subject RIV: JG - Metallurgy

  8. Developmental and Reproductive Effects of SE5-OH: An Equol-Rich Soy-Based Ingredient

    International Nuclear Information System (INIS)

    Matulka, R.A.; Burdock, G.; Matsuura, I.; Uesugi, T.; Ueno, T.

    2009-01-01

    Consumption of the isoflavones daidzein, genistein, glycitein, and their structural analogues is generally considered beneficial to human health. Equol is not found in soy, but is converted from daidzein by human gut bacterial flora. Research indicates that between 30-50% of the population is capable of converting daidzein to equol; therefore, there has been recent development of a new equol-rich functional food that relies on bacterial conversion of daidzein to equol under strictly controlled conditions. Therefore, a new equol-rich soy product (SE5-OH) has been developed, based on the bacterial conversion of daidzein; and its reproductive and developmental toxicity has been evaluated in a two-generation study and a developmental toxicity study with Sprague-Dawley rats at dose levels of 200, 1000, and 2000 mg/kg/day by gavage. SE5-OH contains approximately 0.65% equol, 0.024% daidzein, 0.022% genistein, and 0.30% glycitein. From the reproductive study, the no-observed-adverse-effect-level (NOAEL) for SE5-OH determined for both male and female rats is 1000 mg/kg/day (6.5 mg equol/kg/day). In the developmental toxicity phase of the study, no effects by SE5-OH were found in the embryo-fetus at any of the doses tested. The NOAEL for developmental effects of SE5-OH is 2000 mg/kg/day (13 mg equol/kg/day).

  9. Developmental and Reproductive Effects of SE5-OH: An Equol-Rich Soy-Based Ingredient

    Directory of Open Access Journals (Sweden)

    Ray A. Matulka

    2009-01-01

    Full Text Available Consumption of the isoflavones daidzein, genistein, glycitein, and their structural analogues is generally considered beneficial to human health. Equol is not found in soy, but is converted from daidzein by human gut bacterial flora. Research indicates that between 30–50% of the population is capable of converting daidzein to equol; therefore, there has been recent development of a new equol-rich functional food that relies on bacterial conversion of daidzein to equol under strictly controlled conditions. Therefore, a new equol-rich soy product (SE5-OH has been developed, based on the bacterial conversion of daidzein; and its reproductive and developmental toxicity has been evaluated in a two-generation study and a developmental toxicity study with Sprague-Dawley rats at dose levels of 200, 1000, and 2000 mg/kg/day by gavage. SE5-OH contains approximately 0.65% equol, 0.024% daidzein, 0.022% genistein, and 0.30% glycitein. From the reproductive study, the no-observed-adverse-effect-level (NOAEL for SE5-OH determined for both male and female rats is 1000 mg/kg/day (6.5 mg equol/kg/day. In the developmental toxicity phase of the study, no effects by SE5-OH were found in the embryo-fetus at any of the doses tested. The NOAEL for developmental effects of SE5-OH is 2000 mg/kg/day (13 mg equol/kg/day.

  10. Corn stover harvest strategy effects on grain yield and soil quality indicators

    International Nuclear Information System (INIS)

    Douglas, K.; Stuart, B.; Adam, W.

    2013-01-01

    Developing strategies to collect and use cellulo sic biomass for bio energy production is important because those materials are not used as human food sources. This study compared corn (Zea mays L.) stover harvest strategies on a 50 ha Clarion- Nicol let-Webster soil Association site near Emmetsburg, Iowa, USA. Surface soil samples (0 to 15 cm) were analyzed after each harvest to monitor soil organic carbon (Soc), ph, phosphorus (P) and potassium (K) changes. Grain yields in 2008, before the stover harvest treatments were imposed, averaged 11.4 Mg ha-1. In 2009, 2010, and 2011 grain yields averaged 10.1, 9.7, and 9.5 Mg ha-1, respectively. Although grain yields after stover harvest strategies imposed were lower than in 2008, there were no significant differences among the treatments. Four-year average stover collection rates ranged 1.0 to 5.2 Mg ha-1 which was 12 to 60% of the above-ground biomass. Soc showed a slight decrease during the study, but the change was not related to any specific stover harvest treatment. Instead, we attribute the Soc decline to the tillage intensity and lower than expected crop yields. Overall, these results are consistent with other Midwestern USA studies that indicate corn stover should not be harvested if average grain yields are less than 11 Mg ha-1

  11. Heavy-element yields and abundances of asymptotic giant branch models with a Small Magellanic Cloud metallicity

    Science.gov (United States)

    Karakas, Amanda I.; Lugaro, Maria; Carlos, Marília; Cseh, Borbála; Kamath, Devika; García-Hernández, D. A.

    2018-06-01

    We present new theoretical stellar yields and surface abundances for asymptotic giant branch (AGB) models with a metallicity appropriate for stars in the Small Magellanic Cloud (SMC, Z = 0.0028, [Fe/H] ≈ -0.7). New evolutionary sequences and post-processing nucleosynthesis results are presented for initial masses between 1 and 7 M⊙, where the 7 M⊙ is a super-AGB star with an O-Ne core. Models above 1.15 M⊙ become carbon rich during the AGB, and hot bottom burning begins in models M ≥ 3.75 M⊙. We present stellar surface abundances as a function of thermal pulse number for elements between C to Bi and for a selection of isotopic ratios for elements up to Fe and Ni (e.g. 12C/13C), which can be compared to observations. The integrated stellar yields are presented for each model in the grid for hydrogen, helium, and all stable elements from C to Bi. We present evolutionary sequences of intermediate-mass models between 4 and 7 M⊙ and nucleosynthesis results for three masses (M = 3.75, 5, and 7 M⊙) including s-process elements for two widely used AGB mass-loss prescriptions. We discuss our new models in the context of evolved AGB and post-AGB stars in the SMCs, barium stars in our Galaxy, the composition of Galactic globular clusters including Mg isotopes with a similar metallicity to our models, and to pre-solar grains which may have an origin in metal-poor AGB stars.

  12. Lignin-rich biomass of cotton by-products for biorefineries via pyrolysis.

    Science.gov (United States)

    Chen, Jiao; Liang, Jiajin; Wu, Shubin

    2016-10-01

    Pyrolysis was demonstrated to investigate the thermal decomposition characteristics and potential of lignin-rich cotton by-products cotton exocarp (CE) and spent mushroom substrate consisted of cotton by-products (MSC) for biorefineries. The chemical component and structure alteration of CE and MSC was found to affect their thermochemical behaviors. The bio-oil yield from CE was 58.13wt% while the maximum yield from MSC was 45.01% at 600°C. The phenolic compounds obtained from CE and MSC were 33.9% and 39.2%, respectively. The yield of acetic acid from MSC between 400 and 600°C was about 30-38% lower than that from CE, which suggests the high quality of bio-oil was obtained. Biochar from MSC via slow pyrolysis had a high mass yield (44.38wt%) with well-developed pore structure. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Maximum credibly yield for deuteriuim-filled double shell imaging targets meeting requirements for yield bin Category A

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Douglas Carl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Loomis, Eric Nicholas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-17

    We are anticipating our first NIF double shell shot using an aluminum ablator and a glass inner shell filled with deuterium shown in figure 1. The expected yield is between a few 1010 to a few 1011 dd neutrons. The maximum credible yield is 5e+13. This memo describes why, and what would be expected with variations on the target. This memo evaluates the maximum credible yield for deuterium filled double shell capsule targets with an aluminum ablator shell and a glass inner shell in yield Category A (< 1014 neutrons). It also pertains to fills of gas diluted with hydrogen, helium (3He or 4He), or any other fuel except tritium. This memo does not apply to lower z ablator dopants, such as beryllium, as this would increase the ablation efficiency. This evaluation is for 5.75 scale hohlraum targets of either gold or uranium with helium gas fills with density between 0 and 1.6 mg/cc. It could be extended to other hohlraum sizes and shapes with slight modifications. At present only laser pulse energies up to 1.5 MJ were considered with a single step laser pulse of arbitrary shape. Since yield decreases with laser energy for this target, the memo could be extended to higher laser energies if desired. These maximum laser parameters of pulses addressed here are near the edge of NIF’s capability, and constitute the operating envelope for experiments covered by this memo. We have not considered multiple step pulses, would probably create no advantages in performance, and are not planned for double shell capsules. The main target variables are summarized in Table 1 and explained in detail in the memo. Predicted neutron yields are based on 1D and 2D clean simulations.

  14. Modeling Aquatic Macroinvertebrate Richness Using Landscape Attributes

    Directory of Open Access Journals (Sweden)

    Marcia S. Meixler

    2015-01-01

    Full Text Available We used a rapid, repeatable, and inexpensive geographic information system (GIS approach to predict aquatic macroinvertebrate family richness using the landscape attributes stream gradient, riparian forest cover, and water quality. Stream segments in the Allegheny River basin were classified into eight habitat classes using these three landscape attributes. Biological databases linking macroinvertebrate families with habitat classes were developed using life habits, feeding guilds, and water quality preferences and tolerances for each family. The biological databases provided a link between fauna and habitat enabling estimation of family composition in each habitat class and hence richness predictions for each stream segment. No difference was detected between field collected and modeled predictions of macroinvertebrate families in a paired t-test. Further, predicted stream gradient, riparian forest cover, and total phosphorus, total nitrogen, and suspended sediment classifications matched observed classifications much more often than by chance alone. High gradient streams with forested riparian zones and good water quality were predicted to have the greatest macroinvertebrate family richness and changes in water quality were predicted to have the greatest impact on richness. Our findings indicate that our model can provide meaningful landscape scale macroinvertebrate family richness predictions from widely available data for use in focusing conservation planning efforts.

  15. Species richness, area and climate correlates

    DEFF Research Database (Denmark)

    Nogues, David Bravo; Bastos Araujo, Miguel

    2006-01-01

    affects: (1) the selection of climate variables entering a species richness model; and (2) the accuracy of models in predicting species richness in unsampled grid cells. Location Western Europe. Methods Models are developed for European plant, breeding bird, mammal and herptile species richness using...... seven climate variables. Generalized additive models are used to relate species richness, climate and area. Results We found that variation in the grid cell area was large (50 × 50 km: 8-3311 km2; 220 × 220: 193-55,100 km2), but this did not affect the selection of variables in the models. Similarly...... support the assumption that variation in near-equal area cells may be of second-order importance for models explaining or predicting species richness in relation to climate, although there is a possibility that drops in accuracy might increase with grid cell size. The results are, however, contingent...

  16. Effect of irrigation water salinity and zinc application on yield, yield components and zinc accumulation of wheat

    Directory of Open Access Journals (Sweden)

    mohamad ahmadi

    2009-06-01

    Full Text Available Salinity stress is one of the most important problems of agriculture in crop production in arid and semi arid regions. Under these conditions, in addition to management strategies, proper and adequate nutrition also has an important role in crop improvement. A greenhouse experiment was conducted to study the effect of 4 different irrigation water salinities (blank, 4, 8 and 12 dS m-1, prepared with 1:1 molar ratio of chlorides of calcium and sodium and magnesium sulphate salts. and 5 different zinc applications (0, 10, 20, 30 mg Kg-1 soil and foliar application of salt of zinc sulphate on yield, yield components and zinc concentration of wheat, using a completely randomized design, factorial with three replications. Plant height, spike length, 1000 grain weight, number of grain per spike, grain and straw yield was decreased by Irrigation water salinity. And all of these parameters were improved by zinc application except 1000 grain weight. Zinc absorption and concentration in straw and grain was decreased by Saline water compared to blank. And concentration of zinc significantly was increased in straw and grain by increase zinc application. The results indicated that, zinc application under low to medium salinity conditions improved growth and yield of wheat due to decreasing the impacts salinity.

  17. Specific heat of MgB{sub 2} after irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Wang Yuxing [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland); Bouquet, Frederic [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland); Sheikin, Ilya [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland); Toulemonde, Pierre [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland); Revaz, Bernard [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland); Eisterer, Michael [Atominstitut der Oesterreichischen Universitaeten, A-1020 Vienna (Austria); Weber, Harald W [Atominstitut der Oesterreichischen Universitaeten, A-1020 Vienna (Austria); Hinderer, Joerg [GHMFL, Max-Planck Institute Grenoble, BP 166, F-38042, Grenoble (France); Junod, Alain [Universite de Geneve, Departement de physique de la matiere condensee, 24 quai Ernest-Ansermet, CH-1211 Geneva (Switzerland)

    2003-02-19

    We studied the effect of disorder on the superconducting properties of polycrystalline MgB{sub 2} by specific-heat measurements. In the pristine state, these measurements give a bulk confirmation of the presence of two superconducting gaps with 2{delta}{sub 0}/k{sub B}T{sub c}=1.3 and 3.9 with nearly equal weights. The scattering introduced by irradiation suppresses T{sub c} and tends to average the two gaps although less than predicted by theory. We also found that by a suitable irradiation process by fast neutrons, a substantial bulk increase of dH{sub c2}/dT at T{sub c} can be obtained without sacrificing more than a few degrees in T{sub c}. The upper critical field of the sample after irradiation exceeds 28 T at T{yields}0.

  18. Evaluation of E2 form factor = 24Mg

    International Nuclear Information System (INIS)

    Marinelli, J.R.; Moreira, J.R.

    1988-11-01

    Longitudinal and transverse electron scattering form factors for the 2 + state at 1.37 Mev of the 24 Mg nucleus was evaluated with rotational model wavefunctions. Four different approaches were used for the transverse E2 form factor: PHF, cranking model, ridig rotor and irrotational flow. For the nuclear intrinsic wavefunction, the Nilsson model was assumed in all approaches yielding the calculation of the form factor in PWBA and DWBA. The results are discussed and compared with a recent measurement performed with 180 0 electron scattered from this state. The DWBA calculation, taking into account first order corrections shows that PHF and irrotational flow models give the best agreements with the available data and compete in quality with more complex calculation performed under the 'shell model' approach. (author) [pt

  19. Mg Incorporation Efficiency in Pulsed MOCVD of N-Polar GaN:Mg

    Science.gov (United States)

    Marini, Jonathan; Mahaboob, Isra; Hogan, Kasey; Novak, Steve; Bell, L. D.; Shahedipour-Sandvik, F.

    2017-10-01

    We report on the effect of growth polarity and pulsed or δ -doped growth mode on impurity incorporation in metalorganic chemical vapor deposition-grown GaN. In Ga-polar orientation, up to 12× enhancement in Mg concentration for given Mg flow rate is observed, resulting in enhanced p-type conductivity for these samples. In contrast, this enhancement effect is greatly diminished for N-polar samples, falling off with increasing Mg flow and showing maximum enhancement of 2.7× at 30 nmol/min Mg flow. At higher Mg flow rates, Mg incorporation at normal levels did not correspond to p-type conductivity, which may be due to Mg incorporation at nonacceptor sites. Concentrations of C, O, and Si were also investigated, revealing dependence on Mg flow in N-polar pulsed samples. Carbon incorporation was found to decrease with increasing Mg flow, and oxygen incorporation was found to remain high across varied Mg flow. These effects combine to result in N-polar samples that are not p-type when using the pulsed growth mode.

  20. Structural characteristics and corrosion behavior of biodegradable Mg-Zn, Mg-Zn-Gd alloys.

    Science.gov (United States)

    Kubásek, J; Vojtěch, D

    2013-07-01

    In this research, binary Mg-Zn (up to 3 wt% Zn) and ternary Mg-Zn-Gd (up to 3 wt% Gd, 3 wt% Zn) alloys were prepared by induction melting in an argon atmosphere. The structures of these alloys were characterized using light and scanning electron microscopy, energy dispersive spectrometry, X-ray diffraction and X-ray fluorescence. In addition, Brinell hardness measurements were taken to supplement these studies. Corrosion behavior was evaluated by immersion tests and potentiodynamic measurements in a physiological solution (9 g/l NaCl). Depending on the composition, structures of the as-cast alloys contained α-Mg dendrites, MgZn, Mg5Gd and Mg3Gd2Zn3 phases. Compared to pure Mg, zinc improved the corrosion resistance of binary Mg-Zn. Gadolinium also improved the corrosion resistance in the case of Mg-1Zn-3Gd alloy. The highest corrosion rate was observed for Mg-3Zn-3Gd alloy. Our results improve the understanding of the relationships between the structure and corrosion behavior of our studied alloy systems.

  1. Yield surface evolution for columnar ice

    Science.gov (United States)

    Zhou, Zhiwei; Ma, Wei; Zhang, Shujuan; Mu, Yanhu; Zhao, Shunpin; Li, Guoyu

    A series of triaxial compression tests, which has capable of measuring the volumetric strain of the sample, were conducted on columnar ice. A new testing approach of probing the experimental yield surface was performed from a single sample in order to investigate yield and hardening behaviors of the columnar ice under complex stress states. Based on the characteristic of the volumetric strain, a new method of defined the multiaxial yield strengths of the columnar ice is proposed. The experimental yield surface remains elliptical shape in the stress space of effective stress versus mean stress. The effect of temperature, loading rate and loading path in the initial yield surface and deformation properties of the columnar ice were also studied. Subsequent yield surfaces of the columnar ice have been explored by using uniaxial and hydrostatic paths. The evolution of the subsequent yield surface exhibits significant path-dependent characteristics. The multiaxial hardening law of the columnar ice was established experimentally. A phenomenological yield criterion was presented for multiaxial yield and hardening behaviors of the columnar ice. The comparisons between the theoretical and measured results indicate that this current model is capable of giving a reasonable prediction for the multiaxial yield and post-yield properties of the columnar ice subjected to different temperature, loading rate and path conditions.

  2. Measurements of beryllium sputtering yields at JET

    Science.gov (United States)

    Jet-Efda Contributors Stamp, M. F.; Krieger, K.; Brezinsek, S.

    2011-08-01

    The lifetime of the beryllium first wall in ITER will depend on erosion and redeposition processes. The physical sputtering yields for beryllium (both deuterium on beryllium (Be) and Be on Be) are of crucial importance since they drive the erosion process. Literature values of experimental sputtering yields show an order of magnitude variation so predictive modelling of ITER wall lifetimes has large uncertainty. We have reviewed the old beryllium yield experiments on JET and used current beryllium atomic data to produce revised beryllium sputtering yields. These experimental measurements have been compared with a simple physical sputtering model based on TRIM.SP beryllium yield data. Fair agreement is seen for beryllium yields from a clean beryllium limiter. However the yield on a beryllium divertor tile (with C/Be co-deposits) shows poor agreement at low electron temperatures indicating that the effect of the higher sputtering threshold for beryllium carbide is important.

  3. Investigation on the production of hydrogen rich gas in a plasma converter for motorcycle applications

    International Nuclear Information System (INIS)

    Horng, R.-F.; Chang, Y.-P.; Wu, S.-C.

    2006-01-01

    A plasma fuel converter producing a hydrogen rich gas fuel has been designed and constructed. The methodology included using a high voltage electric arc generator to ionize the mixture of methane fuel and air, which was then reformed into a hydrogen rich gas. It transpired from the experiment that the higher the arc frequency, the higher was the generated hydrogen concentration, with a maximum concentration of 43 vol.% attained with an arc frequency of 200 Hz and an O/C (O 2 /CH 4 ) ratio of 0.10. The maximum hydrogen yield of 0.55 was obtained with an arc frequency of 200 Hz and an O/C ratio between 0.20 and 0.25. By fueling a four stroke motorcycle engine with the hydrogen rich gas, low emissions during the cold start idle condition can be obtained

  4. Measurement of total reaction cross sections of exotic neutron rich nuclei

    International Nuclear Information System (INIS)

    Mittig, W.; Chouvel, J.M.; Wen Long, Z.

    1987-01-01

    Total reaction cross-sections of neutron rich nuclei from C to Mg in a thick Si-target have been measured using the detection of the associated γ-rays in a 4Π-geometry. This cross-section strongly increases with neutron excess, indicating an increase of as much as 15% of the reduced strong absorption radius with respect to stable nuclei

  5. Reaction cross section measurements of neutron-rich exotic nuclei in the vicinity of closed shells N=20 and N=28; Mesures de section efficace de reaction de noyaux exotiques riches en neutrons dans la zone de fermeture des couches N=20 et N=28

    Energy Technology Data Exchange (ETDEWEB)

    Khouaja, A

    2003-12-01

    Using the direct method, the mean energy integrated reaction cross section was investigated for a wide range of neutron-rich nuclei (N {yields} Ar) at GANIL. Using the parametrisation of S. Kox, 19 new radii measurements (reaction cross sections) were obtained. By the isotopic, isotonic and isospin dependence, the evolution of the strong reduced radius was studied according to the excess of neutrons. New halo effect is proposed to the nuclei of Mg{sup 35} and S{sup 44}. A quadratic parametrization is also proposed for the nuclear radius as a function of the isospin in the region of closed shells N=8 and N=28. In addition, we used a modified version of the Glauber model for studying the tail and matter distribution of nuclei. Indeed, using our new data the effects of the nuclear size (root mean square radii) and the matter distribution (diffusivity) were de-convoluted for each isotope. The root mean square radii of Na and Mg isotopes obtained so far were consistent with the ones from literature. (author)

  6. Morphology and the structure of quasicrystal phase in as-cast and melt-spun Mg-Zn-Y-Zr alloys

    International Nuclear Information System (INIS)

    Tang, Y.L.; Zhao, D.S.; Shen, N.F.

    1993-01-01

    During recent years, many researchers have investigated the experimental and theoretical aspects of quasicrystal materials. In some Mg alloys (Mg 32 Al 17 Zn 32 , Mg 32 (Al,Zn) 49 , Mg 32 (Al,Zn,Cu) 49 , Mg 4 CuAl 6 and Ga 16 Mg 32 Zn 52 ), icosahedral quasicrystals (IQC) have been found. However, most of the quasicrystals in these alloys were formed under a rapid solidification condition. In the recent study on Mg-Zn-(Zr,Y) as-cast alloys, the authors identified a new Mg-rich and a Zn-rich IQC by X-ray diffraction (XRD) and electron microscopy (EM). The discovery of Mg-Zn-Y IQC is of interest because it formed in an as-cast ingot and did not contain the element Al, which is the major constituent of nearly all IQC forming alloys reported. Also, analyses on IQC in as-cast and RS Mg alloys with the composition have not previously been carried out. In this paper, TEM and XRD investigations were completed on IQC formed in a Mg-Zn-Y-Zr cast ingot and melt-spun ribbons for microstructure comparison

  7. Palladium, platinum, rhodium, iridium and ruthenium in chromite- rich rocks from the Samail ophiolite, Oman.

    Science.gov (United States)

    Page, N.J.; Pallister, J.S.; Brown, M.A.; Smewing, J.D.; Haffty, J.

    1982-01-01

    30 samples of chromitite and chromite-rich rocks from two stratigraphic sections, 250 km apart, through the basal ultramafic member of the Samail ophiolite were spectrographically analysed for platinum-group elements (PGE) and for Co, Cu, Ni and V. These data are reported as are Cr/(Cr + Al), Mg/(Mg + Fe) and wt.% TiO2 for most samples. The chromitite occurs as pods or lenses in rocks of mantle origin or as discontinuous layers at the base of the overlying cumulus sequence. PGE abundances in both sections are similar, with average contents in chromite-rich rocks: Pd 8 ppb, Pt 14 ppb, Rh 6 ppb, Ir 48 ppb and Ru 135 ppb. The PGE data, combined with major-element and petrographic data on the chromitite, suggest: 1) relatively larger Ir and Ru contents and highest total PGE in the middle part of each section; 2) PGE concentrations and ratios do not correlate with coexisting silicate and chromite abundances or chromite compositions; 3) Pd/PGE, on average, increases upward in each section; 4) Samail PGE concentrations, particularly Rh, Pt and Pd, are lower than the average values for chromite-rich rocks in stratiform intrusions. 2) suggests that PGEs occur in discrete alloy or sulphide phases rather than in the major oxides or silicates, and 4) suggests that chromite-rich rocks from the oceanic upper mantle are depleted in PGE with respect to chondrites. L.C.C.

  8. Structure of Light Neutron-rich Nuclei

    International Nuclear Information System (INIS)

    Dlouhy, Zdenek

    2007-01-01

    In this contribution we searched for irregularities in various separation energies in the frame of mass measurement of neutron-rich nuclei at GANIL. On this basis we can summarize that the new doubly magic nuclei are 8 He, 22 O and 24 O. They are characterized by extra stability and, except 24 O, they cannot accept and bind additional neutrons. However, if we add to these nuclei a proton we obtain 9 Li and 25 F which are the core for two-neutron halo nucleus 11 Li and enables that fluorine can bound even 6 more neutrons, respectively. In that aspect the doubly magic nuclei in the neutron-rich region can form the basis either for neutron halo or very neutron-rich nuclei. (Author)

  9. Origin of the latitudinal richness gradient

    DEFF Research Database (Denmark)

    Engemann, Kristine; Sandel, Brody Steven; Enquist, Brian J.

    2015-01-01

    Spatial variation in richness patterns must be due to variation in rates of speciation, extinction, immigration and emigration. Hotspots of diversity can occur either because they are hotspots of speciation (cradles) or cold spots of extinction (museums) – two major hypotheses that make contrasting...... predictions for the phylogenetic structure of communities. We test these hypotheses by comparing centers of species richness and phylogenetic clustering for vascular plants in the New World. Range maps for 88,417 plant species were extracted from the Botanical Information and Ecology Network (BIEN) database...... and combined with the BIEN mega phylogeny of >80,000 species. We calculated the Phylogenetic Diversity Index (PDI) and Net Relatedness Index (NRI) for each cell in a 100×100 km grid using a new computationally efficient algorithm. Species richness patterns were compared to patterns of PDI and NRI. We found...

  10. Platelet-Rich Plasma Increases Pigmentation.

    Science.gov (United States)

    Uysal, Cagri A; Ertas, Nilgun Markal

    2017-11-01

    Platelet-rich plasma (PRP) is an autologous solution of plasma containing 4 to 7 times the baseline concentration of human platelets. Platelet-rich plasma has been widely popular in facial rejuvenation to attenuate wrinkles and has been practically used. The authors have been encountering various patients of increased hiperpigmentation following PRP applications that were performed to attenuate the postinflammatory hiperpigmentation especially after laser treatment. The authors have been using PRP for facial rejuvenation in selected patients and in 1 patient the authors have encountered increased pigmentation over the pigmented skin lesions that were present before the application. The authors recommend that the PRP might increase pigmentation especially in the face region and precautions might be taken before and after the application. Platelet-rich plasma should not be used for the treatment of post inflammatory hiperpigmentation.

  11. Atomic structure of pyramidal defects in GaN:Mg: Influence of annealing

    Energy Technology Data Exchange (ETDEWEB)

    Liliental-Weber, Z.; Tomaszewicz, T.; Zakharov, D.; O' Keefe, M. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Hautakangas, S.; Saarinen, K. [Materials Science and Engineering, University of California, Berkeley, Berkeley, CA 94720 (United States); Freitas, J.A.; Henry, R.L. [ESTD-Electronic Materials Branch, Naval Research Laboratory, Washington, D.C. 20375 (United States)

    2006-05-15

    The atomic structure of the characteristic defects (Mg-rich hexagonal pyramids) in p-doped bulk and MOCVD GaN:Mg thin films grown with Ga polarity was determined at atomic resolution by direct reconstruction of the scattered electron wave in a transmission electron microscope. Small cavities were present inside the defects, confirmed also with positron annihilation. The inside walls of the cavities were covered by GaN of reverse polarity compared to the matrix. Annealing of the MOCVD layers lead to slight increase of the defect size and an increase of the room temperature photoluminescence intensity. Positron annihilation confirms presence of vacancy clusters of different sizes triggered by the Mg doping in as-grown samples and decrease of their concentration upon annealing at 900 and 1000 C. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  12. Thermoelectric power of PrMg3

    Science.gov (United States)

    Isikawa, Yosikazu; Somiya, Kazuya; Koyanagi, Huruto; Mizushima, Toshio; Kuwai, Tomohiko; Tayama, Takashi

    2010-01-01

    PrMg3 is supposed to be one of the strongly correlated electron systems originated from the hybridization between the Pr 4f and conduction electrons, because the gigantic electronic specific heat coefficient C/T was observed at low temperatures. However, a typical behaviour of - ln T dependence was not observed in the temperature dependence of the electrical resistivity. The thermoelectric power S is a powerful tool to investigate the density of states at the Fermi energy. We measured carefully the thermoelectric power of PrMg3 in the temperature range between 2 and 300 K. S is extremely small, ranged within ±1 μV/K over the whole temperature. The value of S/T at low temperature limit was also significantly smaller than expected from the specific heat results. We therefore conclude that the density of state at the Fermi level is not enhanced in PrMg3.

  13. Thermoelectric power of PrMg3

    International Nuclear Information System (INIS)

    Isikawa, Yosikazu; Somiya, Kazuya; Koyanagi, Huruto; Mizushima, Toshio; Kuwai, Tomohiko; Tayama, Takashi

    2010-01-01

    PrMg 3 is supposed to be one of the strongly correlated electron systems originated from the hybridization between the Pr 4f and conduction electrons, because the gigantic electronic specific heat coefficient C/T was observed at low temperatures. However, a typical behaviour of - ln T dependence was not observed in the temperature dependence of the electrical resistivity. The thermoelectric power S is a powerful tool to investigate the density of states at the Fermi energy. We measured carefully the thermoelectric power of PrMg 3 in the temperature range between 2 and 300 K. S is extremely small, ranged within ±1 μV/K over the whole temperature. The value of S/T at low temperature limit was also significantly smaller than expected from the specific heat results. We therefore conclude that the density of state at the Fermi level is not enhanced in PrMg 3 .

  14. Raman-spectroscopic (Fe/Fe+Mg, CO2) and Structural studies of Mg-Fe cordierites

    International Nuclear Information System (INIS)

    Haefeker, U.

    2013-01-01

    In the course of this dissertation synthetic hexagonal and orthorhombic Mg-Fe-cordierites have been investigated with Raman-spectroscopy and XRD methods. Cordierite´s Mg- and Fe-end-members as well as their Mg-Fe solid solutions with the chemical formula (Mg, Fe 2+ ) 2 Al 4 Si 5 O 18 *nH 2 O have been synthesized. Raman-data of synthetic hydrous Mg- and Fe-cordierites have been obtained in the wavenumber-region 100-1250 cm-1 and the experimental data were then compared with the results of quantum-mechanical calculations. 86 theoretical bands could be related to specific vibrational modes of the tetrahedral and octahedral sites of the cordierite structure. Maximum and mean deviation between experimentally-derived bands and calculated modes were ±7 cm -1 for Mg-cordierite and ±19 cm -1 for Fe-cordierite. Spectra comparison revealed a trend of peak downshifting as a consequence of Fe-incorporation. The calculations now allow more accurate interpretation of the Raman spectra with respect to structural changes of cordierite, resulting from Al-Si ordering and Mg-Fe exchange. Atomic motions in cordierite have been compared with those of the structurally similar mineral beryl. Investigations of 16 H 2 O-bearing synthetic well-ordered Mg-Fe-cordierites (XFe =0-1) with micro-Raman spectroscopy revealed a linear correlation between the Fe/Mg ratio and the position of certain Raman peaks. The peaks (wave-number Mg-/Fe-cordierite) at 122/111, 262/257, 430/418, 579/571, 974/967, and 1012/1007 cm -1 were selected for a detailed deconvolution analysis . The shifts of these peaks were then plotted vs. XFe and regression of the data lead to the formulation of a set of linear equations. In addition, the effect of different H 2 O contents and the degree of Al-Si ordering on the Fe/Mg determination were also investigated. Testing the calibration against data from six well-characterized natural cordierite samples yielded excellent agreement. Existing calibration diagrams for CO 2

  15. Microstructure and properties of hot extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5) alloys

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Bao-sheng; Kuang, Ya-fei; Fang, Da-qing; Chai, Yue-sheng [Taiyuan Univ. of Science and Technology (China). College of Materials Science and Engineering; Taiyuan Univ. of Science and Technology (China). Engineering Research Center for Magnesium Alloys of Shanxi Province; Zhang, Yue-zhong [Taiyuan Univ. of Science and Technology (China). Engineering Research Center for Magnesium Alloys of Shanxi Province; Taiyuan Univ. of Science and Technology (China). College of Chemical and Biological Engineering

    2017-04-15

    In petroleum drilling engineering, materials with high strength and rapid degradation are required for degradable fracturing ball applications. In this work, the microstructure, mechanical properties, and corrosion behavior of extruded Mg-3Zn-Y-xCu (x = 0, 1, 3, 5 weight percent) alloys are investigated using optical microscopy, scanning electronic microscopy equipped with energy dispersive X-ray spectroscopy, X-ray diffraction, transmission electronic microscopy, compression tests, electrochemical measurements, and hydrogen evolution tests, to explore their potential as excellent candidate alloys for degradable fracturing ball applications. It is found that the Mg-3Zn-Y alloy is mainly composed of α-Mg, Mg{sub 3}Zn{sub 3}Y{sub 2}, and Mg{sub 3}Zn{sub 6}Y phases. After Cu addition, a new MgZnCu phase is formed, while the Mg{sub 3}Zn{sub 3}Y{sub 2} phase disappears. The Mg-3Zn-Y-3Cu alloy shows the highest compressive strength (473 MPa) and yield strength (402 MPa), mainly attributed to the combined effect of the fine-grain and dispersed precipitation of Mg{sub 3}Zn{sub 6}Y and MgZnCu. The corrosion rate of Mg-3Zn-Y-3Cu reaches 0.41 mm day{sup -1} in 3.5 wt.% KCl solution. Consequently, Mg-3Zn-Y-3Cu alloy is a suitable degradable fracturing ball-seat material.

  16. Photosynthetic capacity, nutrient status and growth of maize (Zea mays L. upon MgSO4 leaf-application

    Directory of Open Access Journals (Sweden)

    Mareike eJezek

    2015-01-01

    Full Text Available The major plant nutrient magnesium is involved in numerous physiological processes and its deficiency can severely reduce the yield and quality of crops. Since Mg availability in soil and uptake into the plant is often limited by unfavorable soil or climatic conditions, application of Mg onto leaves, the site with highest physiological Mg demand, might be a reasonable alternative fertilization strategy. This study aimed to investigate, if MgSO4 leaf-application in practically relevant amounts can efficiently alleviate the effects of Mg starvation in maize, namely reduced photosynthesis capacity, disturbed ion homeostasis and growth depression. Results clearly demonstrated that Mg deficiency could be mitigated by MgSO4 leaf-application as efficiently as by resupply of MgSO4 via the roots in vegetative maize plants. Significant increases in SPAD values and net rate of CO2-assimilation as well as enhanced shoot biomass have been achieved. Ion analysis furthermore revealed an improvement of the nutrient status of Mg-deficient plants with regard to [Mg], [K] and [Mn] in distinct organs, thereby reducing the risk of Mn-toxicity at the rootside, which often occurs together with Mg deficiency on acid soils. In conclusion, foliar fertilization with Mg proved to be an efficient strategy to adequately supply maize plants with magnesium and might hence be of practical relevance to correct nutrient deficiencies during the growing season.

  17. In vitro and in vivo corrosion, mechanical properties and biocompatibility evaluation of MgF2-coated Mg-Zn-Zr alloy as cancellous screws.

    Science.gov (United States)

    Li, Zhen; Shizhao, Sun; Chen, Minfang; Fahlman, Bradley Dean; Debao Liu; Bi, Hongwei

    2017-06-01

    Magnesium (Mg) and its alloys as biodegradable materials have received much attention in the orthopedics applications; however, the corrosion behavior of these metals in vivo remains challenging. In this work, a dense and nanoscale magnesium fluoride (MgF 2 ) coating was deposited on the surface of Mg-Zn-Zr (MZZ) alloy cancellous screw. The MZZ cancellous screw with MgF 2 coating maintained an integrated shape and high yield tensile stress after 30days immersion in SBF, comparing with the bare screw. Hydrogen releasing rate of the MZZ samples was suppressed at a lower level at the initial stage, which is in favour of the adhesion of the cells. And in vivo experiments indicated that MgF 2 -coated MZZ screws presented advantages in cytocompatibility, osteoconductivity and osteogenesis of cancellous bone in rabbits. Corrosion rate in vivo perfusion environment increased very slowly with time in long-term study, which was an opposite trend in vitro static immersion test. Moreover, maximum corrosion rate (CR max ), a critical calculation method of corrosion rate was introduced to predict fracture regions of the sample. The MZZ alloy with MgF 2 coating possesses a great potential for clinical applications for internal fracture fixation repair. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Fast Photon Detection for COMPASS RICH1

    CERN Document Server

    Abbon, P; Angerer, H; Apollonio, M; Birsa, R; Bordalo, P; Bradamante, F; Bressan, A; Busso, L; Chiosso, M; Ciliberti, P; Colantoni, M L; Costa, S; Dibiase, N; Dafni, T; Dalla Torre, S; Diaz, V; Duic, v; Delagnes, E; Deschamps, H; Eyrich, W; Faso, D; Ferrero, A; Finger, M; Finger, M Jr; Fischer, H; Gerassimov, S; Giorgi, M; Gobbo, B; Hagemann, R; Von Harrach, D; Heinsius, F H; Joosten, R; Ketzer, B; Königsmann, K; Kolosov, V N; Konorov, I; Kramer, D; Kunne, F; Levorato, S; Maggiora, A; Magnon, A; Mann, A; Martin, A; Menon, G; Mutter, A; Nähle, O; Neyret, D; Nerling, F; Pagano, P; Paul, S; Panebianco, S; Panzieri, D; Pesaro, G; Pizzolotto, C; Polak, J; Rebourgeard, P; Rocco, E; Robinet, F; Schiavon, P; Schill, C; Schoenmeier, P; Silva, L; Slunecka, M; Steiger, L; Sozzi, F; Sulc, M; Svec, M; Tessarotto, F; Teufel, A; Wollny, H

    2006-01-01

    The new photon detection system for COMPASS RICH-1 has been designed to cope with the demanding requests of operation at high beam intensity and at high trigger rates. The detection technique in the central region of RICH-1 has been changed with a system based on multianode photomultipliers coupled to individual fused silica lens telescopes and to a fast, almost dead time free readout system based on the MAD-4 amplifier-discriminator and the F1 TDC-chip. The new photon detection system design and construction are described, as well as its first response in the experiment.

  19. Hamman-Rich syndrome in a goldsmith

    International Nuclear Information System (INIS)

    Kirchner, J.; Stein, A.; Jacobi, V.; Viel, K.

    1997-01-01

    We report the case of a 54-year-old goldsmith admitted because of dyspnea on exertion, persistent cough, and weakness under the suspicion of exogenous allergic alveolitis. He rapidly developed progressive lung fibrosis with exitus letalis 7 weeks after admission. Radiological examination (chest X-ray and HRCT) first showed ground glass opacities, and later rapid development of severe interstitial pattern with architectural distraction. The findings were similar to idiopathic lung fibrosis; however, the rare Hamman-Rich syndrome was confirmed by progressive course of the disease. Correlations between Hamann-Rich syndrome and idiopathic lung fibrosis are discussed. (orig.) [de

  20. Performance of two honey bee subspecies during harsh weather and Acacia gerrardii nectar-rich flow

    Directory of Open Access Journals (Sweden)

    Awad Mohamed Awad

    Full Text Available ABSTRACT Both climatic factors and bee forage characteristics affect the population size and productivity of honey bee colonies. To our knowledge, no scientific investigation has as yet considered the potential effect of nectar-rich bee forage exposed to drastic subtropical weather conditions on the performance of honey bee colonies. This study investigated the performance of the honey bee subspecies Apis mellifera jemenitica Ruttner (Yemeni and Apis mellifera carnica Pollmann (Carniolan in weather that was hot and dry and in an environment of nectar-rich flora. The brood production, food storage, bee population and honey yield of Yemeni (native and Carniolan (imported colonies on Talh trees (Acacia gerrardii Benth., a nectar-rich, subtropical, and summer bee forage source in Central Arabia were evaluated. Owing to their structural and behavioral adaptations, the Yemeni bees constructed stronger (high population size colonies than the Carniolan bees. Although both groups yielded similar amounts of Talh honey, the Yemeni bees consumed their stored honey rapidly if not timely harvested. A. m. jemenitica has a higher performance than A. m. carnica during extremely hot-dry conditions and A. gerrardii nectar-rich flow.

  1. Resource stoichiometry and availability modulate species richness and biomass of tropical litter macro-invertebrates.

    Science.gov (United States)

    Jochum, Malte; Barnes, Andrew D; Weigelt, Patrick; Ott, David; Rembold, Katja; Farajallah, Achmad; Brose, Ulrich

    2017-09-01

    High biodiversity and biomass of soil communities are crucial for litter decomposition in terrestrial ecosystems such as tropical forests. However, the leaf litter that these communities consume is of particularly poor quality as indicated by elemental stoichiometry. The impact of resource quantity, quality and other habitat parameters on species richness and biomass of consumer communities is often studied in isolation, although much can be learned from simultaneously studying both community characteristics. Using a dataset of 780 macro-invertebrate consumer species across 32 sites in tropical lowland rain forest and agricultural systems on Sumatra, Indonesia, we investigated the effects of basal resource stoichiometry (C:X ratios of N, P, K, Ca, Mg, Na, S in local leaf litter), litter mass (basal resource quantity and habitat space), plant species richness (surrogate for litter habitat heterogeneity), and soil pH (acidity) on consumer species richness and biomass across different consumer groups (i.e. 3 feeding guilds and 10 selected taxonomic groups). In order to distinguish the most important predictors of consumer species richness and biomass, we applied a standardised model averaging approach investigating the effects of basal resource stoichiometry, litter mass, plant species richness and soil pH on both consumer community characteristics. This standardised approach enabled us to identify differences and similarities in the magnitude and importance of such effects on consumer species richness and biomass. Across consumer groups, we found litter mass to be the most important predictor of both species richness and biomass. Resource stoichiometry had a more pronounced impact on consumer species richness than on their biomass. As expected, taxonomic groups differed in which resource and habitat parameters (basal resource stoichiometry, litter mass, plant species richness and pH) were most important for modulating their community characteristics. The importance

  2. Excited states in 22Mg via the 12C(12C,2n)22Mg reaction

    International Nuclear Information System (INIS)

    Jewett, Cybele; Baktash, Cyrus; Bardayan, Daniel W.; Blackmon, Jeff C.; Chipps, K.; Galindo-Uribarri, Alfredo; Greife, U.; Gross, Carl J.; Jones, K. L.; Liang, Junjien; Livesay, Jake; Kozub, R. L.; Nesaraja, Caroline D; Radford, David C.; Sarazin, F.; Smith, Michael Scott; Thomas, J. S.; Yu, Chang-Hong

    2007-01-01

    The 12C(12C, 2n)22Mg reaction was measured with the CLARION array and the RMS separator at the Holifield Facility of Oak Ridge National Laboratory. This experiment was performed to gather more information on the excited states in 22Mg, which might be of relevance to recent radioactive ion beam measurements of the astrophysically important 21Na(p,γ)22Mg reaction. The results are compared to direct measurements, transfer experiments and a competing experiment performed with Gammasphere

  3. Mifepristone 5 mg versus 10 mg for emergency contraception: double-blind randomized clinical trial

    Directory of Open Access Journals (Sweden)

    Carbonell JL

    2015-01-01

    Full Text Available Josep Lluis Carbonell,1 Ramon Garcia,2 Adriana Gonzalez,2 Andres Breto,2 Carlos Sanchez2 1Mediterranea Medica Clinic, Valencia, Spain; 2Eusebio Hernandez Gynecology and Obstetrics Teaching Hospital, Havana, Cuba Purpose: To estimate the efficacy and safety of 5 mg and 10 mg mifepristone for emergency contraception up to 144 hours after unprotected coitus. Methods: This double-blind randomized clinical trial was carried out at Eusebio Hernandez Hospital (Havana, Cuba. A total of 2,418 women who requested emergency contraception after unprotected coitus received either 5 mg or 10 mg mifepristone. The variables for assessing efficacy were the pregnancies that occurred and the fraction of pregnancies that were prevented. Other variables assessed were the side effects of mifepristone, vaginal bleeding, and changes in the date of the following menstruation. Results: There were 15/1,206 (1.2% and 9/1,212 (0.7% pregnancies in the 5 mg and 10 mg group, respectively (P=0.107. There were 88% and 93% prevented pregnancies in the 5 mg and 10 mg group, respectively. The side effect profiles were similar in both groups. Delayed menstruation ≥7 days was experienced by 4.9% and 11.0% of subjects in the 5 mg and 10 mg group, respectively (P=0.001. There was a significant high failure rate for women weighing >75 kg in the 5 mg group. Conclusion: It would be advisable to use the 10 mg dose of mifepristone for emergency contraception as there was a trend suggesting that the failure rate of the larger dose was lower. Keywords: mifepristone, emergency contraception

  4. Microstructure and degradation performance of biodegradable Mg-Si-Sr implant alloys.

    Science.gov (United States)

    Gil-Santos, Andrea; Marco, Iñigo; Moelans, Nele; Hort, Norbert; Van der Biest, Omer

    2017-02-01

    In this work the microstructure and degradation behavior of several as-cast alloy compositions belonging to the Mg rich corner of the Mg-Si-Sr system are presented and related. The intermetallic phases are identified and analyzed describing the microstructure evolution during solidification. It is intended in this work to obtain insight in the behavior of the ternary alloys in in vitro tests and to analyze the degradation behavior of the alloys under physiologically relevant conditions. The as-cast specimens have been exposed to immersion tests, both mass loss (ML) and potentiodynamic polarization (PDP). The degradation rate (DR) have been assessed and correlated to microstructure features, impurity levels and alloy composition. The initial reactions resulted to be more severe while the degradation stabilizes with time. A higher DR is related with a high content of the Mg 17 Sr 2 phase and with the presence of coarse particles of the intermetallics Mg 2 Si, MgSiSr and MgSi 2 Sr. Specimens with a higher DR typically have higher levels of impurities and alloy contents. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Structurally characterized 1,1,3,3-tetramethylguanidine solvated magnesium aryloxide complexes: [Mg(mu-OEt)(DBP)(H-TMG)]2, [Mg(mu-OBc)(DBP)(H-TMG)]2, [Mg(mu-TMBA)(DBP)(H-TMG)]2, [Mg(mu-DPP)(DBP)(H-TMG)]2, [Mg(BMP)2(H-TMG)2], [Mg(O-2,6-Ph2C6H3)2 (H-TMG)2].

    Science.gov (United States)

    Monegan, Jessie D; Bunge, Scott D

    2009-04-06

    The synthesis and structural characterization of several 1,1,3,3-tetramethylguanidine (H-TMG) solvated magnesium aryloxide complexes are reported. Bu(2)Mg was successfully reacted with H-TMG, HOC(6)H(3)(CMe(3))(2)-2,6 (H-DBP), and either ethanol, a carboxylic acid, or diphenyl phosphate in a 1:1 ratio to yield the corresponding [Mg(mu-L)(DBP)(H-TMG)](2) where L = OCH(2)CH(3) (OEt, 1), O(2)CC(CH(3))(3) (OBc, 2), O(2)C(C(6)H(2)-2,4,6-(CH(3))(3)) (TMBA, 3), or O(2)P(OC(6)H(5))(2) (DPP, 4). Bu(2)Mg was also reacted with two equivalents of H-TMG and HOC(6)H(3)(CMe(3))-2-(CH(3))-6 (BMP) or HO-2,6-Ph(2)C(6)H(3) to yield [Mg(BMP)(2)(H-TMG)(2)] (5) and [Mg(O-2,6-Ph(2)C(6)H(3))(2)(H-TMG)(2)] (6). Compounds 1-6 were characterized by single-crystal X-ray diffraction. Polymerization of l- and rac-lactide with 1 was found to generate polylactide (PLA). A discussion concerning the relevance of compounds 2 - 4 to the structure of Mg-activated phosphatase enzymes is also provided. The bulk powders for all complexes were found to be in agreement with the crystal structures based on elemental analyses, FT-IR spectroscopy, and (1)H, (13)C and (31)P NMR studies.

  6. Superconducting properties of MgB2 particle impregnated with Mg-based alloys

    International Nuclear Information System (INIS)

    Shimizu, Yusuke; Matsuda, Kenji; Mizutani, Manabu; Nishimura, Katsuhiko; Kawabata, Tokimasa; Ikeno, Susumu; Hishinuma, Yoshimitsu; Aoyama, Shigeki

    2011-01-01

    The three-dimensional penetration method combined with semi-solid casting (SS-3DPC) was utilized to prepare magnesium diboride (MgB 2 ) powder composite materials with various host materials of Mg, Mg-3%Al, Mg-3%Al-1%Zn, Mg-9%Al, and Mg-9%Al-1%Zn. X-ray diffraction measurements indicated predominant peak patterns of MgB 2 and a host alloy, implying that the host material tightly bonded MgB 2 grains without melting the MgB 2 powder. This was confirmed by SEM images. Measured electrical resistivity and magnetization versus temperature showed clear signals of superconducting transition temperature of 27-38 K for all the samples cut out from the billets. Magnetic hysteresis loop observed at 5 K enabled us to estimate a critical current density (J c ) based on the extended Bean model. Additions of aluminum and zinc elements to magnesium host-matrix were found to enhance J c and increase residual resistivity (ρ 0 ) suggesting that aluminum and zinc have an effect on pinning magnetic flux flow for J c enhancement, and scattering conduction electrons for increase of ρ 0 . (author)

  7. Low-lying dipole strength of neutron-rich 'island of inversion' nuclei around n ∼ 20

    International Nuclear Information System (INIS)

    Datta Pramanik, U.; Chakraborty, S.; Ray, I.

    2009-01-01

    Magic numbers are the basic building blocks of nuclear structure since last fifty years. Recently, through various experimental results using Radioactive Ion Beam (RIB) facilities, it has been observed that those long cherished magic numbers are not valid anymore in the neutron rich nuclei like 32 Mg etc. The breakdown of magic number was hinted in the late 1980 's by Thibault et. al. in sodium nuclei ( 31,32 Na). Motobayashi et. al. showed large deformation for 32 Mg which leads to the failure of magic number at N = 20. Exploration into the cause of this breakdown shows the filling of higher pf orbitals rather than the pure lower sd orbitals in the ground state of the neutron-rich nuclei like Ne, Na, Mg in the region N∼20. Thus there is obviously an inversion in nuclear orbitals and hence the so called name 'island of inversion'. This year, we have performed an experiment at GSI, Darmstadt. The measurement of dipole threshold strength of neutron-rich nucleus (N∼20) through electromagnetic excitation was done using LAND-FRS setup. Through this dipole strength, we would like to probe directly the quantum numbers of the valence neutrons in neutron rich nuclei like 31-33 Mg, 33-35 Al, 29-30 Na, 25-27 Ne, 24 F etc.

  8. Geochemistry and oxygen isotope composition of main-group pallasites and olivine-rich clasts in mesosiderites

    DEFF Research Database (Denmark)

    Greenwood, Richard C.; Barrat, Jean-Alix; Scott, Edward R. D.

    2015-01-01

    origin. Although the Dawn mission did not detect mesosiderite-like material on Vesta, evidence linking the mesosiderites and HEDs includes: (i) theirnearly identical oxygen isotope compositions; (ii) the presence in both of coarse-grained Mg-rich olivines; (iii) both have synchronous Lu-Hf and Mn-Cr ages...

  9. Tracing subduction zone fluid-rock interactions using trace element and Mg-Sr-Nd isotopes

    Science.gov (United States)

    Wang, Shui-Jiong; Teng, Fang-Zhen; Li, Shu-Guang; Zhang, Li-Fei; Du, Jin-Xue; He, Yong-Sheng; Niu, Yaoling

    2017-10-01

    , whereas high Pb* and 87Sr/86Sr eclogites have mantle-like δ26Mg values, suggesting that the two fluid components have diverse influences on the Mg isotopic systematics of these eclogites. The LILE-rich fluid component, possibly derived from mica-group minerals, contains a considerable amount of isotopically heavy Mg that has shifted the δ26Mg of the eclogites towards higher values. By contrast, the 87Sr/86Sr- and Pb-rich fluid component, most likely released from epidote-group minerals in metasediments, has little Mg so as not to modify the Mg isotopic composition of the eclogites. In addition, the influence of talc-derived fluid might be evident in a very few eclogites that have low Rb/Sr and Ba/Pb but slightly heavier Mg isotopic compositions. These findings represent an important step toward a broad understanding of the Mg isotope geochemistry in subduction zones, and contributing to understanding why island arc basalts have averagely heavier Mg isotopic compositions than the normal mantle.

  10. Electronic structure of MgB2

    Indian Academy of Sciences (India)

    Abstract. Results of ab initio electronic structure calculations on the compound MgB2 using the. FPLAPW method employing GGA for the exchange-correlation energy are presented. Total energy minimization enables us to estimate the equilibrium volume, c/a ratio and the bulk modulus, all of which are in excellent ...

  11. Electronic structure of MgB 2

    Indian Academy of Sciences (India)

    Results of ab initio electronic structure calculations on the compound MgB2 using the FPLAPW method employing GGA for the exchange-correlation energy are presented. Total energy minimization enables us to estimate the equilibrium volume, / ratio and the bulk modulus, all of which are in excellent agreement with ...

  12. doped LiMgPO4 phosphor

    Indian Academy of Sciences (India)

    attention because of their remarkable luminescence proper- ties and .... Figure 1. (a) X-ray diffraction patterns of LiMgPO4:Tb3+ phosphor and (b) standard data. ICDD file. .... ground signal which affects the signal to noise ratio [17]. MDD was ...

  13. Systematics of Fission-Product Yields

    International Nuclear Information System (INIS)

    Wahl, A.C.

    2002-01-01

    Empirical equations representing systematics of fission-product yields have been derived from experimental data. The systematics give some insight into nuclear-structure effects on yields, and the equations allow estimation of yields from fission of any nuclide with atomic number Z F = 90 thru 98, mass number A F = 230 thru 252, and precursor excitation energy (projectile kinetic plus binding energies) PE = 0 thru ∼200 MeV--the ranges of these quantities for the fissioning nuclei investigated. Calculations can be made with the computer program CYFP. Estimates of uncertainties in the yield estimates are given by equations, also in CYFP, and range from ∼ 15% for the highest yield values to several orders of magnitude for very small yield values. A summation method is used to calculate weighted average parameter values for fast-neutron (∼ fission spectrum) induced fission reactions

  14. Systematics of Fission-Product Yields

    Energy Technology Data Exchange (ETDEWEB)

    A.C. Wahl

    2002-05-01

    Empirical equations representing systematics of fission-product yields have been derived from experimental data. The systematics give some insight into nuclear-structure effects on yields, and the equations allow estimation of yields from fission of any nuclide with atomic number Z{sub F} = 90 thru 98, mass number A{sub F} = 230 thru 252, and precursor excitation energy (projectile kinetic plus binding energies) PE = 0 thru {approx}200 MeV--the ranges of these quantities for the fissioning nuclei investigated. Calculations can be made with the computer program CYFP. Estimates of uncertainties in the yield estimates are given by equations, also in CYFP, and range from {approx} 15% for the highest yield values to several orders of magnitude for very small yield values. A summation method is used to calculate weighted average parameter values for fast-neutron ({approx} fission spectrum) induced fission reactions.

  15. Interface modulated currents in periodically proton exchanged Mg doped lithium niobate

    Energy Technology Data Exchange (ETDEWEB)

    Neumayer, Sabine M.; Rodriguez, Brian J., E-mail: brian.rodriguez@ucd.ie, E-mail: gallo@kth.se [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland); Conway Institute of Biomolecular and Biomedical Research, University College Dublin, Belfield, Dublin 4 (Ireland); Manzo, Michele; Gallo, Katia, E-mail: brian.rodriguez@ucd.ie, E-mail: gallo@kth.se [Department of Applied Physics, KTH-Royal Institute of Technology, Roslagstullbacken 21, 10691 Stockholm (Sweden); Kholkin, Andrei L. [Department of Physics and CICECO-Aveiro Institute of Materials, 3810-193 Aveiro, Portugal and Institute of Natural Sciences, Ural Federal University, 620000 Ekaterinburg (Russian Federation)

    2016-03-21

    Conductivity in Mg doped lithium niobate (Mg:LN) plays a key role in the reduction of photorefraction and is therefore widely exploited in optical devices. However, charge transport through Mg:LN and across interfaces such as electrodes also yields potential electronic applications in devices with switchable conductivity states. Furthermore, the introduction of proton exchanged (PE) phases in Mg:LN enhances ionic conductivity, thus providing tailorability of conduction mechanisms and functionality dependent on sample composition. To facilitate the construction and design of such multifunctional electronic devices based on periodically PE Mg:LN or similar ferroelectric semiconductors, fundamental understanding of charge transport in these materials, as well as the impact of internal and external interfaces, is essential. In order to gain insight into polarization and interface dependent conductivity due to band bending, UV illumination, and chemical reactivity, wedge shaped samples consisting of polar oriented Mg:LN and PE phases were investigated using conductive atomic force microscopy. In Mg:LN, three conductivity states (on/off/transient) were observed under UV illumination, controllable by the polarity of the sample and the externally applied electric field. Measurements of currents originating from electrochemical reactions at the metal electrode–PE phase interfaces demonstrate a memresistive and rectifying capability of the PE phase. Furthermore, internal interfaces such as domain walls and Mg:LN–PE phase boundaries were found to play a major role in the accumulation of charge carriers due to polarization gradients, which can lead to increased currents. The insight gained from these findings yield the potential for multifunctional applications such as switchable UV sensitive micro- and nanoelectronic devices and bistable memristors.

  16. Test-beam Results from a RICH Detector Prototype Using Aerogel Radiator and Pixel Hybrid Photon Detectors

    CERN Document Server

    Aglieri-Rinella, G; Van Lysebetten, A; Piedigrossi, D; Wyllie, K; Bellunato, T F; Calvi, M; Matteuzzi, C; Musy, M; Perego, D L; Somerville, L P; Newby, C; Easo, S; Wotton, S

    2006-01-01

    A test-beam study was performed at CERN with a Ring Imaging Cherenkov (RICH) prototype using three pixel Hybrid Photon Detectors. Results on the photon yield and Cherenkov angle resolution are presented here, for the Aerogel radiator and also for reference runs taken with Nitrogen radiator.

  17. Experiments with neutron-rich isomeric beams

    International Nuclear Information System (INIS)

    Rykaczewski, K.; Lewitowicz, M.; Pfuetzner, M.

    1998-01-01

    A review of experimental results obtained on microsecond-isomeric states in neutron-rich nuclei produced in fragmentation reactions and studied with SISSI-Alpha-LISE3 spectrometer system at GANIL Caen is given. The perspectives of experiments based on secondary reactions with isomeric beams are presented

  18. Development of a Rich Picture editor

    DEFF Research Database (Denmark)

    Valente, Andrea; Marchetti, Emanuela

    2010-01-01

    rich picture practice into software proved difficult, therefore, we decided to follow a user-centered approach: design and implement a prototype with basic functionalities, then run a usability test with a few students and professionals. The feedback collected in the test validated our hypothesis circa...

  19. Leveraging data rich environments using marketing analytics

    NARCIS (Netherlands)

    Holtrop, Niels

    2017-01-01

    With the onset of what is popularly known as “big data”, increased attention is being paid to creating value from these data rich environments. Within the field of marketing, the analysis of customer and market data supported by models is known as marketing analytics. The goal of these analyses is

  20. Proximity focusing RICH with TOF capabilities

    International Nuclear Information System (INIS)

    Korpar, S.; Adachi, I.; Fujita, K.; Fukushima, T.; Gorisek, A.; Hayashi, D.; Iijima, T.; Ikado, T.; Ishikawa, T.; Kawai, H.; Kozakai, Y.; Krizan, P.; Kuratani, A.; Mazuka, Y.; Nakagawa, T.; Nishida, S.; Ogawa, S.; Pestotnik, R.; Seki, T.; Sumiyoshi, T.; Tabata, M.; Unno, Y.

    2007-01-01

    A proximity focusing RICH counter with a multi-channel micro-channel plate (MCP) PMT was tested as a time-of-flight counter. Cherenkov photons emitted in the radiator medium as well as in the entrance window of the PMT were used for the time-of-flight measurement, and an excellent performance of the counter could be demonstrated

  1. Probing luminescence centers in Na rich feldspar

    DEFF Research Database (Denmark)

    Prasad, Amit Kumar; Lapp, Torben; Kook, Myung Ho

    2016-01-01

    our understanding of the luminescence mechanisms and recombination sites, in a sample of Na rich plagioclase feldspar (oligoclase). Both the UV and violet–blue emissions show resonant excitations arising from a distribution of energy levels. We propose, contrary to the general understanding...

  2. Technology-Rich Schools Up Close

    Science.gov (United States)

    Levin, Barbara B.; Schrum, Lynne

    2013-01-01

    This article observes that schools that use technology well have key commonalities, including a project-based curriculum and supportive, distributed leadership. The authors' research into tech-rich schools revealed that schools used three strategies to integrate technology successfully. They did so by establishing the vision and culture,…

  3. Platelet-rich fibrin: the benefits.

    Science.gov (United States)

    Kumar, Yuvika Raj; Mohanty, Sujata; Verma, Mahesh; Kaur, Raunaq Reet; Bhatia, Priyanka; Kumar, Varun Raj; Chaudhary, Zainab

    2016-01-01

    Current published data presents confusing results about the effects of platelet-rich fibrin on bone, and there is a need for studies that throw light on its effect. Our main objective therefore was to evaluate (by fractal analysis) osseous regeneration in extraction sockets with and without platelet-rich fibrin in a study with a substantial sample and a reliable technique to calibrate its effects on bone cells. We also assessed the soft tissue response. Thirty-four patients had their bilaterally impacted third molars (68 surgical sites) extracted in this split-mouth study, following which platelet-rich fibrin was placed in one of the sockets. Patients were followed up clinically and radiographically, and a pain score and fractal analysis were used to evaluate healing of soft tissue and bone, respectively. We conclude that platelet-rich fibrin improves healing of both soft and hard tissues. Although osseous healing did not differ significantly between the groups, healing of soft tissue as judged by the pain score was significantly better in the experimental group. Copyright © 2015 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  4. Power Divider for Waveforms Rich in Harmonics

    Science.gov (United States)

    Sims, William Herbert, III

    2005-01-01

    A method for dividing the power of an electronic signal rich in harmonics involves the use of an improved divider topology. A divider designed with this topology could be used, for example, to propagate a square-wave signal in an amplifier designed with a push-pull configuration to enable the generation of more power than could be generated in another configuration.

  5. Microstructure evolution and texture development in thermomechanically processed Mg-Li-Al based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Vinod [Department of Materials Science and Engineering, IIT Kanpur (India); Govind [Vikram Sarabhai Space Center, Trivandrum (India); Shekhar, Rajiv; Balasubramaniam, R. [Department of Materials Science and Engineering, IIT Kanpur (India); Balani, Kantesh, E-mail: kbalani@iitk.ac.in [Department of Materials Science and Engineering, IIT Kanpur (India)

    2012-06-15

    Highlights: Black-Right-Pointing-Pointer Thermomechanical processing of novel LAT 971 and LATZ 9531 Mg-Al-Li based alloys. Black-Right-Pointing-Pointer Microstructural deviation from the equilibrium phase diagram. Black-Right-Pointing-Pointer Disparity in texture of these alloys after hot-rolling (recrystallization and grain growth). Black-Right-Pointing-Pointer Role of alloying and phase distribution in affecting the texture/interplaner spacing. - Abstract: In the present study, the influence of alloying and thermomechanical processing on the microstructure and texture evolution on the two Mg-Li-Al based alloys, namely Mg-9 wt% Li-7 wt% Al-1 wt% Sn (LAT971) and Mg-9 wt% Li-5 wt% Al-3 wt% Sn-1 wt% Zn (LATZ9531) has been elicited. Novel Mg-Li-Al based alloys were cast (induction melting under protective atmosphere) followed by hot rolling at {approx}573 K with a cumulative reduction of five. A contrary dual phase dendritic microstructure rich in {alpha}-Mg, instead of {beta}-Li phase predicted by equilibrium phase diagram of Mg-Li binary alloy was observed. Preferential presence of Mg-Li-Sn primary precipitates (size 4-10 {mu}m) within {alpha}-Mg phase and Mg-Li-Al secondary precipitates (<3 {mu}m) interspersed in {beta}-Li indicated their degree of dissolution during hot-rolling and homogenization in the dual phase matrix. Presence of Al, Sn and Zn alloying elements in the Mg-Li based alloy has resulted an unusual dual-phase microstructure, change in the lattice parameter, and intriguing texture evolution after hot-rolling of cast LAT 971 and LATZ9531 alloy. Strong texture was absent in the as-cast samples whereas texture development after hot-rolling revealed an increased activity of the non-basal (101{sup Macron }0) slip planes. The quantification of the grain average misorientation (less than 2 Degree-Sign ) using electron backscattered diffraction confirmed the presence of strain free grains in majority of the grains (fraction >0.75) after hot-rolling of Mg

  6. Yield stress determination of a physical gel

    DEFF Research Database (Denmark)

    Hvidt, Søren

    2013-01-01

    Pluronic F127 solutions form gels in water with high elastic moduli. Pluronic gels can, however, only withstand small deformations and stresses. Different steady shear and oscillatory methods traditionally used to determine yield stress values are compared. The results show that the yield stresses...... values of these gels depend on test type and measurement time, and no absolute yield stress value can be determined for these physical gels....

  7. Alumina Yield in the Bayer Process

    Science.gov (United States)

    Den Hond, R.

    The alumina industry has historically been able to reduce alumina production costs, by increasing the liquor alumina yield. To know the potential for further yield increases, the phase diagram of the ternary system Na2O-Al2O -H2O at various temperature levels was analysed. It was found that the maximum theorical precipitation alumina yield is 160 g/l, while that for digestion was calculated to be 675 g/l.

  8. Equity Volatility and Corporate Bond Yields

    OpenAIRE

    John Y. Campbell; Glen B. Taksler

    2002-01-01

    This paper explores the effect of equity volatility on corporate bond yields. Panel data for the late 1990s show that idiosyncratic firm-level volatility can explain as much cross-sectional variation in yields as can credit ratings. This finding, together with the upward trend in idiosyncratic equity volatility documented by Campbell, Lettau, Malkiel, and Xu (2001), helps to explain recent increases in corporate bond yields. The definitive version is available at www.blackwell-synergy.com.

  9. Thermoluminescence responses of photon- and electron-irradiated lithium potassium borate co-doped with Cu+Mg or Ti+Mg

    International Nuclear Information System (INIS)

    Alajerami, Y.S.M.; Hashim, S.; Ramli, A.T.; Saleh, M.A.; Saripan, M.I.; Alzimami, K.; Min Ung, Ngie

    2013-01-01

    New glasses Li 2 CO 3 –K 2 CO 3 –H 3 BO 3 (LKB) co-doped with CuO and MgO, or with TiO 2 and MgO, were synthesized by the chemical quenching technique. The thermoluminescence (TL) responses of LKB:Cu,Mg and LKB:Ti,Mg irradiated with 6 MV photons or 6 MeV electrons were compared in the dose range 0.5–4.0 Gy. The standard commercial dosimeter LiF:Mg,Ti (TLD-100) was used to calibrate the TL reader and as a reference in comparison of the TL properties of the new materials. The dependence of the responses of the new materials on 60 Co dose is linear in the range of 1–1000 Gy. The TL yields of both of the co-doped glasses and TLD-100 are greater for electron irradiation than for photon irradiation. The TL sensitivity of LKB:Ti,Mg is 1.3 times higher than the sensitivity of LKB:Cu,Mg and 12 times less than the sensitivity of TLD-100. The new TL dosimetric materials have low effective atomic numbers, good linearity of the dose responses, excellent signal reproducibility, and a simple glow curve structure. This combination of properties makes them suitable for radiation dosimetry. - Highlights: • Enhancement of about three times has been shown with the increment of MgO. • A comparison was carried out between the TL responses of the prepared dosimeters and TLD-100. • The prepared dosimeters show simple glow curve, low Z material and excellent reproducibility. • The TL measurements show a linear dose response in a long span of exposures. • The electron response shows 1.18 times greater than photon response for the prepared dosimeters

  10. Status of fission product yield data

    International Nuclear Information System (INIS)

    Cuninghame, J.G.

    1978-01-01

    The topics covered in this paper are: (a) cumulative yields in thermal neutron fission and in fast fission up to 14 MeV incident neutron energy, (b) dependence of the yields on incident neutron energy and spectrum, (c) independent yields, (d) charge dispersion and distribution, and (e) yields of light particles from ternary fission. The paper reviews information on these subjects for fission of actinides from 232 Th upwards with special emphasis on data published since the 1973 Bologna FPND Panel, compares data sets, and discusses the gaps still to be found in them. (author)

  11. Food for thought: pretty good multispecies yield

    DEFF Research Database (Denmark)

    Rindorf, Anna; Dichmont, C. M.; Levin, P.S.

    2017-01-01

    good multidimensional yield to accommodate situations where the yield from a stock affects the ecosystem, economic and social benefits, or sustainability. We demonstrate in a European example that PGMY is a practical concept. As PGMY provides a safe operating space for management that adheres...... that broader ecosystem, economic, and social objectives are addressed. We investigate how the principles of a “pretty good yield” range of fishing mortalities assumed to provide >95% of the average yield for a single stock can be expanded to a pretty good multispecies yield (PGMY) space and further to pretty...

  12. Yield Mapping in Salix; Skoerdekartering av salix

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Christoffer; Gilbertsson, Mikael; Rogstrand, Gustav; Thylen, Lars

    2004-09-01

    The most common species for energy forest production is willow. Willow is able to produce a large amount of biomass in a short period of time. Growing willow has a potential to render a good financial result for the farmer if cultivated on fields with the right conditions and plenty of water. Under the right conditions growing willow can give the farmer a net income of 3,000 SEK (about 430 USD) per hectare and year, which is something that common cereal crops cannot compete with. However, this is not the common case since willow is often grown as a substitute crop on fields where cereal crop yield is low. The aim of this study was to reveal if it is possible to measure yield variability in willow, and if it is possible to describe the reasons for yield variation both within the field but also between different fields. Yield mapping has been used in conventional farming for about a decade. The principles for yield mapping are to continuously measure the yield while registering location by the use of GPS when harvesting the field. The collected data is then used to search for spatial variations within the field, and to try to understand the reasons for this variation. Since there is currently no commercial equipment for yield mapping in willow, a yield mapping system had to be developed within this project. The new system was installed on a Claas Jaguar harvester. The principle for yield mapping on the Claas Jaguar harvester is to measure the distance between the feeding rollers. This distance is correlated to the flow through the harvester. The speed and position of the machine was registered using GPS. Knowing the working width of the harvester this information was used to calculate the yield. All collected data was stored on a PDA computer. Soil samples were also collected from the yield mapped fields. This was to be able to test yield against both physical and chemical soil parameters. The result shows that it is possible to measure spatial variations of yield in

  13. Improving the yield from fermentative hydrogen production.

    Science.gov (United States)

    Kraemer, Jeremy T; Bagley, David M

    2007-05-01

    Efforts to increase H(2) yields from fermentative H(2) production include heat treatment of the inoculum, dissolved gas removal, and varying the organic loading rate. Although heat treatment kills methanogens and selects for spore-forming bacteria, the available evidence indicates H(2) yields are not maximized compared to bromoethanesulfonate, iodopropane, or perchloric acid pre-treatments and spore-forming acetogens are not killed. Operational controls (low pH, short solids retention time) can replace heat treatment. Gas sparging increases H(2) yields compared to un-sparged reactors, but no relationship exists between the sparging rate and H(2) yield. Lower sparging rates may improve the H(2) yield with less energy input and product dilution. The reasons why sparging improves H(2) yields are unknown, but recent measurements of dissolved H(2) concentrations during sparging suggest the assumption of decreased inhibition of the H(2)-producing enzymes is unlikely. Significant disagreement exists over the effect of organic loading rate (OLR); some studies show relatively higher OLRs improve H(2) yield while others show the opposite. Discovering the reasons for higher H(2) yields during dissolved gas removal and changes in OLR will help improve H(2) yields.

  14. Effects of iron on intermetallic compound formation in scandium modified Al–Si–Mg Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Patakham, Ussadawut [National Metal and Materials Technology Center, National Science and Technology Development Agency, 114 Thailand Science Park, Klong Nueng, Klong Luang, Pathumthani 12120 (Thailand); Limmaneevichitr, Chaowalit, E-mail: chaowalit.lim@mail.kmutt.ac.th [Production Engineering Department, Faculty of Engineering, King Mongkut’s University of Technology Thonburi, 126 Pracha-Utid Rd., Bangmod, Tungkhru, Bangkok 10140 (Thailand)

    2014-12-15

    Highlights: • Iron reduces the modification effects of scandium in Al–Si–Mg alloys. • Morphologies of Sc-rich intermetallic phases vary with Fe and Sc contents and the cooling rates. • Sc neutralizes effects of Fe by changing Fe-rich intermetallic phases from platelets to more cubic. - Abstract: In general, iron has a strong tendency to dissolve in molten aluminum. Iron has very low solid solubility in aluminum–silicon casting alloys, so it will form intermetallic compounds that cause detrimental effects on mechanical properties. In this work, the effects of iron on intermetallic compound formations in scandium modified Al–Si–Mg alloys were studied. There were two levels of iron addition (0.2 and 0.4 wt.%) and two levels of scandium addition (0.2 and 0.4 wt.%). We found that the effects of scandium modification decreased with increasing iron addition. The morphologies of the complex intermetallic compounds were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscatter diffraction (EBSD) techniques. It was found that scandium changes the morphology of Fe-rich intermetallic compounds from β-phase (plate-like) to α-phase, which reduces the harmful effects of β-phase.

  15. Preliminary study of the characteristics of a high Mg containing Al-Mg-Si alloy

    International Nuclear Information System (INIS)

    Yan, F; McKay, B J; Fan, Z; Chen, M F

    2012-01-01

    An Al-20Mg-4Si high Mg containing alloy has been produced and its characteristics investigated. The as-cast alloy revealed primary Mg 2 Si particles evenly distributed throughout an α-Al matrix with a β-Al 3 Mg 2 fully divorced eutectic phase observed in interdendritic regions. The Mg 2 Si particles displayed octahedral, truncated octahedral, and hopper morphologies. Additions of Sb, Ti and Zr had a refining influence reducing the size of the Mg 2 Si from 52 ± 4 μm to 25 ± 0.1 μm, 35 ± 1 μm and 34 ± 1 μm respectively. HPDC tensile test samples could be produced with a 0.6 wt.% Mn addition which prevented die soldering. Solution heating for 1 hr was found to dissolve the majority of the Al 3 Mg 2 eutectic phase with no evidence of any effect on the primary Mg 2 Si. Preliminary results indicate that the heat treatment has a beneficial effect on the elongation and the UTS.

  16. Respiratory outcomes following 100 mg/kg v. 200 mg/kg of poractant ...

    African Journals Online (AJOL)

    In keeping with current evidence, the initial dose of poractant alpha was increased from 100 mg/kg to 200 mg/kg. e outcomes of newborns requiring treatment with surfactant before and aer this change were reviewed. Methods. Electronic clinical records were reviewed of infants admitted to ACH who received surfactant ...

  17. Mg/Ca ratio in fertilization and agricultural soils, Mg percent of liming ...

    African Journals Online (AJOL)

    Strong increase of NPK (nitrogen, phosphorus and potassium) in mineral fertilization (fm) included relative delay in Mg supplementation and dilution in plant available silicon (Si) via recycled nutrients (rcl). (Silicon is not included in essential fertilizers in Finland.) Methods: We have assessed old data on Ca and Mg in ...

  18. Effect of fertilizer application on yield of oil palm

    Directory of Open Access Journals (Sweden)

    Eksomtramage, T.

    2001-11-01

    Full Text Available The effects of fertilizer application rates on leaf nutrient contents and yield of oil palm were investigated at the Agricultural and Technological College Plantation in Trang province during May 1998 - June 2001. A five-year-old oil palm plantation, planted on the Na Tham soil series (Fine loamy, mixed, isohyperthermic Oxic Plinthudults with spacing 9x9x9 m, was selected for study. A randomized complete block designwith three replications with 20 palms/replication was used. The treatments included six different rates of fertilizer application. The rates of fertilizer were as follows: T1 (farmer practice, T2 (40% of application rate in T4, T3 (70% of application rate in T4, T4 (urea 2,750 g/plant; triple super phosphate 1,500 g/plant; potassium chloride 4,000 g/plant; kieserite 1,000 g/plant; borate 80 g/plant, T5 (130% of application rate in T4 and T6 (170% of application rate in T4. The high leaf nutrient contents of N, P and K at the range of 2.6-2.8%, 0.16-0.18% and 1.13-1.18%, respectively, were found in the high nutrient application rate treatments (T5, T6. However, the amounts of leaf Ca and Mg in T5 and T6 decreased from 0.75-0.80% and 0.33- 0.37% at the beginning of experiment to 0.65-0.70% and 0.22-0.24%, respectively, at the end of the experiment. Small increases of leaf sulphur and boron up to about 0.20-0.22% and 16-19 mg/kg were also found in the high rate of fertilizer treatments. Accumulated fresh fruit bunch yield (FFB increased according to increasing rate of fertilizer application. Accumulated FFB yield of 268.4 kg/plant in the low fertilizer rate (T1 (farmer practice and 278.8 kg/plant in T2 were found compared with the highest yield of 370.2 kg/plant in the highest fertilizer application treatment (T6 for the 3 years experiment. Regarding the economic return, the medium rate of fertilizer application (T3 which achieved an accumulated FFB yield of 338.0 kg/ plant gave the highest profit with the VCR (Value: Cost ratio of 2.53.

  19. Decay of a Jπ=36+ Resonance in the 24Mg+24Mg Reaction

    International Nuclear Information System (INIS)

    Salsac, M.-D.; Haas, F.; Courtin, S.

    2005-01-01

    For the 24 Mg+ 24 Mg reaction, striking narrow and correlated resonance structures have been observed previously in the excitation functions of the elastic and low-lying channels. In our study we have decided to focus on the resonance at E C M =45.7 MeV, which is known to have J π =36 + . Despite the very high excitation energy(∼60 MeV) in the 48 Cr composite system, this resonance has a narrow total width of 170 keV. To determine precisely which states in the inelastic 24 Mg channels carry away the resonance flux, an experiment, on the 24 Mg + 24 Mg reaction at energies On and OFF resonance, has been performed at the Legnaro Tandem accelerator using the Prisma fragment spectrometer associated with the CLARA γ array

  20. Microbial Species and Functional Diversity in Rice Rhizosphere of High-yield Special Ecological Areas

    Directory of Open Access Journals (Sweden)

    PAN Li-yuan

    2016-11-01

    Full Text Available Taoyuan, Yunnan Province is a special eco-site which keeps the highest yield records of rice cultivation in small planting areas. Soil microbial species and functional diversity were evaluated using cultivation method and BIOLOG ecoplates. The results showed that the microbial community of the high yield region was more abundant, and the total microbial population was 2 times of the control, furthermore, the areas belonged to the healthy "bacteria" soil, which was showed as bacteria > actinomycetes > fungi. Bacteria were the dominant populations in the rhizosphere of high yielding rice field, and the yield formation of rice was not correlated with the depth of soil layers. In order to obtain more species diversity information, Shannon diversity index H, Shannon evenness index E and Simpson index D were analyzed, and the results showed that microbial community diversity and evenness were not the main differences between the high and general yield areas. Then, the functional diversity of soil microbial community was investigated through the average well color development(AWCD and diversity index analyses. The results of AWCD analysis indicated that the metabolic activity of soil microbial community in high yield paddy soils were stronger than the control. Moreover, the difference range from large to small showed as tillering stage > harvest period > seedling period > rotation period, the stronger the rice growth, the greater the difference between the high yield region and the control. At tillering stage and harvest stage, due to the vigorous plant growth, the root exudates were rich, and the microbial communities of high yield paddy soils showed a strong metabolic activity and strong ability to use carbon sources. The results of Shannon, Simpson and McIntosh indices analysis indicated that common microbial species was not a key factor affecting the yield of rice. Tillering stage was a key period for the growth of high yield rice, and many

  1. Microstructures, mechanical properties and corrosion resistances of extruded Mg-Zn-Ca-xCe/La alloys.

    Science.gov (United States)

    Tong, L B; Zhang, Q X; Jiang, Z H; Zhang, J B; Meng, J; Cheng, L R; Zhang, H J

    2016-09-01

    Magnesium alloys are considered as good candidates for biomedical applications, the influence of Ce/La microalloying on the microstructure, mechanical property and corrosion performance of extruded Mg-5.3Zn-0.6Ca (wt%) alloy has been investigated in the current study. After Ce/La addition, the conventional Ca2Mg6Zn3 phases are gradually replaced by new Mg-Zn-Ce/La-(Ca) phases (T1'), which can effectively divide the Ca2Mg6Zn3 phase. The Ca2Mg6Zn3/T1' structure in Mg-Zn-Ca-0.5Ce/La alloy is favorably broken into small particles during the extrusion, resulting in an obvious refinement of secondary phase. The dynamic recrystallized grain size is dramatically decreased after 0.5Ce/La addition, and the tensile yield strength is improved, while further addition reverses the effect, due to the grain coarsening. However, the corrosion resistance of extruded Mg-Zn-Ca alloy deteriorates after Ce/La addition, because the diameter of secondary phase particle is remarkably decreased, which increases the amount of cathodic sites and accelerates the galvanic corrosion process. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Seed priming with iron and zinc in bread wheat: effects in germination, mitosis and grain yield.

    Science.gov (United States)

    Reis, Sara; Pavia, Ivo; Carvalho, Ana; Moutinho-Pereira, José; Correia, Carlos; Lima-Brito, José

    2018-07-01

    Currently, the biofortification of crops like wheat with micronutrients such as iron (Fe) and zinc (Zn) is extremely important due to the deficiencies of these micronutrients in the human diet and in soils. Agronomic biofortification with Fe and Zn can be done through different exogenous strategies such as soil application, foliar spraying, and seed priming. However, the excess of these micronutrients can be detrimental to the plants. Therefore, in the last decade, a high number of studies focused on the evaluation of their phytotoxic effects to define the best strategies for biofortification of bread wheat. In this study, we investigated the effects of seed priming with different dosages (1 mg L -1 to 8 mg L -1 ) of Fe and/or Zn in germination, mitosis and yield of bread wheat cv. 'Jordão' when compared with control. Overall, our results showed that: micronutrient dosages higher than 4 mg L -1 negatively affect the germination; Fe and/or Zn concentrations higher than 2 mg L -1 significantly decrease the mitotic index and increase the percentage of dividing cells with anomalies; treatments performed with 8 mg L -1 of Fe and/or 8 mg L -1 Zn caused negative effects in germination, mitosis and grain yield. Moreover, seed priming with 2 mg L -1 Fe + 2 mg L -1 Zn has been shown to be non-cytotoxic, ensuring a high rate of germination (80%) and normal dividing cells (90%) as well as improving tillering and grain yield. This work revealed that seed priming with Fe and Zn micronutrients constitutes a useful and alternative approach for the agronomic biofortification of bread wheat.

  3. The content of parthenolide and its yield per plant during the growth of Tanacetum parthenium

    NARCIS (Netherlands)

    Hendriks, H; Anderson-Wildeboer, Y.; Bos, R.; Woerdenbag, H.J.

    During the growth of Tanaceum parthenium (L.) Schultz-Bip. Feverfew, Asteraceae) the percentage of parthenolide was the highest at an early stage (just before the formation of stems), The yield of parthenolide per individual plant gradually increased from about 10 mg at the beginning of the study to

  4. Insights into Collisional between Small Bodies: Comparison of Impacted Magnesium-rich Minerals

    Science.gov (United States)

    Lederer, Susan M.; Jensen, E. A.; Strojia, C.; Smith, D. C.; Keller, L. P.; Nakamura-Messenger, K.; Berger, E. L.; Lindsay, S. S.; Wooden, D. H.; Cintala, M. J.; hide

    2013-01-01

    Impacts are sustained by comets and asteroids throughout their lives, especially early in the Solar system's history, as described by the Nice model. Identifying observable properties that may be altered due to impacts can lead to a better understanding their collisional histories. Here, we investigate spectral effects and physical shock features observed in infrared spectra and Transmission Electron Microscope (TEM) images, respectively, of magnesium-rich minerals subjected to shock through impact experiments. Samples of magnesium-rich forsterite (Mg2SiO4, olivine), orthoenstatite (Mg2SiO3, pyroxene), diopside (MgCaSi2O6, monoclinic pyroxene), and magnesite (MgCO3, carbonate) were impacted at speeds of 2.4 km/s, 2.6 km/s and 2.8 km/s. Impact experiments were conducted in the Johnson Space Center Experimental Impact Laboratory using the vertical gun. Clear signatures are observed in both the mid-IR spectra (shift in wavelengths of the spectral peaks and relative amplitude changes) of all minerals except magnesite, and in TEM images (planar dislocations) of both the forsterite and orthoenstatite samples. Further discussion on forsterite and enstatite analyses can be found in Jensen et al., this meeting.

  5. Microstructure and mechanical properties of an extruded Mg-8Bi-1Al-1Zn (wt%) alloy

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Shuaiju [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Yu, Hui, E-mail: yuhuidavid@gmail.com [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Materials Commercialization Center, Korea Institute of Materials Science, Changwon 51508 (Korea, Republic of); Zhang, Huixing [Mechanical and Material School, Tianjin Sino-German University of Applied Sciences, Tianjin 300350 (China); Cui, Hongwei [School of Materials Science and Engineering, Shangdong University of Technology, Zibo 255049 (China); Park, Sung Hyuk [School of Materials Science and Engineering, Kyungpook National University, Daegu 702701 (Korea, Republic of); Zhao, Weiming [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); You, Bong Sun [Materials Commercialization Center, Korea Institute of Materials Science, Changwon 51508 (Korea, Republic of)

    2017-04-06

    In this study, the microstructural evolution and mechanical properties of a newly developed rare earth free Mg-8Bi-1Al-1Zn (BAZ811, in wt%) alloy were investigated and compared with those of a commercial AZ31 alloy. The as-extruded BAZ811 alloy with much finer grain size shows more homogeneous dynamical recrystallized (DRXed) microstructure and weaker basal texture than those of AZ31 alloy. In addition, compared with bimodal structure AZ31 alloy containing only relatively coarse and sparse Al{sub 8}Mn{sub 5} phases, the coexistence of strip-like fragmented Mg{sub 3}Bi{sub 2} precipitate and nano-size Mg{sub 3}Bi{sub 2} particles in the microstructure was observed in BAZ811 alloy. Moreover, the BAZ811 alloy exhibits a tensile yield stress of 291 MPa, an ultimate tensile strength of 331 MPa, an elongation to failure of 14.6% as well as a reduction in yield asymmetry, which is mainly attributed to the combined effects of grain refinement and micro-scale broken Mg{sub 3}Bi{sub 2} particles together with nano-scale spherical Mg{sub 3}Bi{sub 2} precipitates. The strain hardening behavior of both BAZ811 and AZ31 alloys were also discussed in terms of microstructure variation.

  6. MgAl-Layered Double Hydroxide Solid Base Catalysts for Henry Reaction: A Green Protocol

    Directory of Open Access Journals (Sweden)

    Magda H. Abdellattif

    2018-03-01

    Full Text Available A series of MgAl-layered double hydroxide (MgAl-HT, the calcined form at 500 °C (MgAlOx, and the rehydrated one at 25 °C (MgAl-HT-RH were synthesized. Physicochemical properties of the catalysts were characterized by X-ray diffraction (XRD and scanning electron microscopy (SEM. Surface area of the as-synthesized, calcined, and rehydrated catalysts was determined by N2 physisorption at −196 °C. CO2 temperature-programmed desorption (CO2-TPD was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1–15 were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90 °C in liquid phase or under microwave irradiation method. The mesoporous structure and basic nature of the rehydrated solid catalyst were responsible for its superior catalytic efficiency. The robust nature was determined by using the same catalyst five times, where the product % yield was almost unchanged significantly.

  7. Effects of Ca on microstructure, mechanical and corrosion properties and biocompatibility of Mg-Zn-Ca alloys.

    Science.gov (United States)

    Yin, Ping; Li, Nian Feng; Lei, Ting; Liu, Lin; Ouyang, Chun

    2013-06-01

    Zn and Ca were selected as alloying elements to develop an Mg-Zn-Ca alloy system for biomedical application due to their good biocompatibility. The effects of Ca on the microstructure, mechanical and corrosion properties as well as the biocompatibility of the as-cast Mg-Zn-Ca alloys were studied. Results indicate that the microstructure of Mg-Zn-Ca alloys typically consists of primary α-Mg matrix and Ca₂Mg₆Zn₃/Mg₂Ca intermetallic phase mainly distributed along grain boundary. The yield strength of Mg-Zn-Ca alloy increased slightly with the increase of Ca content, whilst its tensile strength increased at first and then decreased. Corrosion tests in the simulated body fluid revealed that the addition of Ca is detrimental to corrosion resistance due to the micro-galvanic corrosion acceleration. In vitro hemolysis and cytotoxicity assessment disclose that Mg-5Zn-1.0Ca alloy has suitable biocompatibility.

  8. The influence of ferric iron in calcined nano-Mg/Al hydrotalcite on adsorption of Cr (VI) from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Lili [College of Chemistry, Dalian University of Technology, Dalian, Liaoning 116023 (China); Ma Wei, E-mail: chmawv@yahoo.com [College of Chemistry, Dalian University of Technology, Dalian, Liaoning 116023 (China); Han Mei; Cheng Zihong [College of Chemistry, Dalian University of Technology, Dalian, Liaoning 116023 (China)

    2011-02-15

    Research highlights: {yields} The reconstruction processes of CH-Mg/Al and CH-Mg/Al/Fe were fast and efficient, but the adsorption of Cr (VI) on CH-Mg/Al/Fe reached equilibrium faster. {yields} The removal mechanism involved not only intercalation but also adsorption on external surface of the layers and interlayer anion exchange. {yields} The existence of Fe3{sup +} in Mg/Al calcined hydrotalcite led to the interlayer anion exchange more difficult and it is affected equilibrium amount of Cr (VI) adsorption. - Abstract: The influence of ferric iron in calcined nano-Mg/Al hydrotalcite on removal of Cr (VI) from aqueous solution was studied from aspects of structure characteristics, adsorption properties and mechanism discussions. The calcined hydrotalcites (CH-Mg/Al and CH-Mg/Al/Fe) were obtained by thermal decomposition of their corresponding precursors and characterized by XRD, TEM, pH{sub PZC} and FTIR. The adsorption properties were studied as a function of pH, initial Cr (VI) concentration and contact time. The results showed that the nature of adsorption is endothermic and spontaneous for both CH-Mg/Al and CH-Mg/Al/Fe, but the thermodynamic parameter value changes revealed the addition of Fe{sup 3+} is disadvantage to adsorption process and the theoretical saturated adsorption capacity decreased by approximately 10.2 mg/g at tested temperatures. The removal mechanism involved not only intercalation but adsorption on external surface of the layers and interlayer anion exchange for both CH-Mg/Al and CH-Mg/Al/Fe. Furthermore, the results also indicated that intercalation accounts for a large proportion during removal process whatever for CH-Mg/Al, or for CH-Mg/Al/Fe. Additionally, the replacement of Al{sup 3+} by Fe{sup 3+} in CH-Mg/Al led to the interlayer anion exchange more difficult. On the basis of the results, it is concluded that the existence of ferric iron in calcined Mg/Al hydrotalcite is unfavorable to removal of Cr (VI) from aqueous solution.

  9. Yields from pyrolysis of refinery residue using a batch process

    Directory of Open Access Journals (Sweden)

    S. Prithiraj

    2017-12-01

    Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

  10. EARLY SPRING APPLICATION OF AMINOETHOXYVINILGLYCINE (AVG INCREASES FRUIT SET AND YIELD OF ‘ROCHA’ PEARS

    Directory of Open Access Journals (Sweden)

    MATEUS DA SILVEIRA PASA

    2017-10-01

    Full Text Available ABSTRACT The low fruit set is one of the main factors leading to poor yield of pear orchards in Brazil. Ethylene is associated with abscission of flowers and fruitlets. Then, the application of ethylene synthesis inhibitors, such as AVG, is a potential tool to increase fruit set of pears. The objective of this study was to evaluate the effect of AVG, sprayed at different rates and timings, on fruit set, yield and fruit quality of ‘Rocha’ pear. The study was performed in a commercial orchard located in the municipality of São Joaquim, SC, during the growing seasons of 2014/2015 and 2015/2016. Plant material consisted of ‘Rocha’ pear trees grafted on quince rootstock ‘BA29’. AVG was tested at different rates (60 mg L-1 and 80 mg L-1 and timings [full bloom, one week after full bloom (WAFB, and two WAFB, either alone or in combination. The experiment was arranged in a randomized block design, with at least five single-tree replications. The fruit set, number of fruit per tree, yield, estimated yield, fruit weight, return bloom, and fruit quality attributes were assessed. Fruit set and yield were consistently increased by single applications of AVG at 60 and 80 mg L-1 at both one and two weeks after full bloom, without negatively affecting fruit quality attributes and return bloom.

  11. Mg II Line Variation of 32 Cygni

    Directory of Open Access Journals (Sweden)

    Young Woon Kang

    1992-12-01

    Full Text Available The Mg II lines have been extracted from the IUE archival spectra of 32 Cygni to investigate the effect of the atmospheric eclipse. The UV light curve has been reduced from the continuum flux at the center wavelength of 2807.5 Å in the IUE spectra. The equivalent width of the Mg II k absoption line has been measured for each spectra. The results of the light variation and flux tracing of the absorption line at the vicinity of the primary eclipse confirmed the atmospheric eclipse. The atmospheric effect lasted until the phase 0.06 in the absorptin line tracing, while it lasted until the phase 0.02 in the UV light curve, respectively.

  12. Crop yield response to increasing biochar rates

    Science.gov (United States)

    The benefit or detriment to crop yield from biochar application varies with biochar type/rate, soil, crop, or climate. The objective of this research was to identify yield response of cotton (Gossypium hirsutum L.), corn (Zea mayes L.), and peanut (Arachis hypogaea L.) to hardwood biochar applied at...

  13. Central Bank Communication and the Yield Curve

    DEFF Research Database (Denmark)

    Leombroni, Matteo; Vedolin, Andrea; Venter, Gyuri

    communication shocks have a significant impact, with intermediate maturities being affected the most; (ii) positive (negative) communication shocks significantly lower (raise) the yield spread between the peripheral and core countries; (iii) this cross-sectional difference arises after the 2008 financial crises......-for-yield investors....

  14. FEM growth and yield data monocultures - Poplar

    NARCIS (Netherlands)

    Mohren, G.M.J.; Goudzwaard, L.; Jansen, J.J.; Oosterbaan, A.; Oldenburger, J.F.; Ouden, den J.

    2016-01-01

    The current database is part of the FEM growth and yield database, a collection of growth and yield data from even-aged monocultures (douglas fir, common oak, poplar, Japanese Larch, Norway spruce, Scots pine, Corsican pine, Austrian pine, red oak and several other species, with only a few plots,

  15. Yield stress of alumina-zirconia suspensions

    International Nuclear Information System (INIS)

    Ramakrishnan, V.; Pradip; Malghan, S.G.

    1996-01-01

    The yield stress of concentrated suspensions of alumina, zirconia, and mixed alumina-zirconia powders was measured by the vane technique as a function of solids loading, relative amounts of alumina and zirconia, and pH. At the isoelectric point (IEP), the yield stress varied as the fourth power of the solids loading. The relative ratio of alumina and zirconia particles was important in determining the yield stress of the suspension at the IEP. The yield stress of single and mixed suspensions showed a marked variation with pH. The maximum value occurred at or near the IEP of the suspension. The effect of electrical double-layer forces on the yield stress can be described on the basis of the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. A normalized yield stress--that is, the ratio of the yield stress at a given pH to the yield stress at the IEP predicted by this model--showed good correlation with experimental data

  16. Effects of land-applied ammonia scrubber solutions on yield, nitrogen uptake, soil test phosphorus and phosphorus runoff

    Science.gov (United States)

    Ammonia (NH3) scrubbers reduce amounts of NH3 and dust released from animal rearing facilities, while generating nitrogen (N) rich solutions, which may be used as fertilizer. The objective of this study was to determine the effects of various NH3 scrubber solutions on yields, N uptake by forage, so...

  17. Adipose tissue-derived mesenchymal stem cell yield and growth characteristics are affected by the tissue-harvesting procedure

    NARCIS (Netherlands)

    Oedayrajsingh-Varma, M. J.; van Ham, S. M.; Knippenberg, M.; Helder, M. N.; Klein-Nulend, J.; Schouten, T. E.; Ritt, M. J. P. F.; van Milligen, F. J.

    2006-01-01

    Adipose tissue contains a stromal vascular fraction that can be easily isolated and provides a rich source of adipose tissue-derived mesenchymal stem cells (ASC). These ASC are a potential source of cells for tissue engineering. We studied whether the yield and growth characteristics of ASC were

  18. High temperature mechanical forming of Mg alloys

    International Nuclear Information System (INIS)

    Mwembela, A.; McQueen, H.J.; Myshlyaev, M.

    2002-01-01

    Mg alloys are hot worked in the range 180-450 o C and 0.0-10 s -1 ; the present project data are compared with a wide selection of published results. The flow stresses and their dependence on temperature and strain rate are fairly similar to simple Al alloys: however, the hot ductility is much lower (≤3 in torsion). Twinning plays a significant role in Mg alloys almost independently of temperature; the twins initiate at low strains in grains poorly oriented for basal slip and in consequence become well disposed for such slip. As T rises, there is increasing formation of subgrains that spread toward the grain centers from grain and twin boundaries: this is indicative of stress concentrations inducing non-basal sup which helps provide the geometrically necessary dislocations. Above about 240 o C, dynamic (DRX) nucleates at grain and twin boundaries, preferentially at intersections; this again is evidence of non-basal slip that provides the highly misoriented cells. The boundaries in which further strain concentrates producing further DRX. The microstructure remains very heterogeneous compared to the uniform dynamically recovered substructure in Al alloys, thus giving rise to the reduced ductility. These results are employed to interpret the mechanical and microstructural behavior of Mg alloys in extrusion, rolling and forging. (author)

  19. Mg,Ca-ATPase activity under irradiation

    International Nuclear Information System (INIS)

    Ladutin, V.V.; Orlova, V.V.; Lob, P.A.; Gerasiminko, I.V.; Mack, E.I.

    2003-01-01

    Full text: The influence of different doses irradiation at the Mg,Ca-ATPase activity at the rat brain has been investigated. The analyses were made at the apparatus of LKB and Carl-Ceis-Jena firm with help of reagents of Sigma and Boehringer firm. Rats decapitated after 1, 3, 6, 24 and 48 h after action of irradiation. Dose 0.206 C/kg. Erythrocytes. 1 and 3h after irradiation influence- decrease of Mg,Ca-ATPase activity to 86-87% relatively control level, 24 and 48 h - increase of activity to the control level. Dose 0.312 C/kg. Large hemispheres. 1h - decrease of ATPase activity to 90% relatively control, 3h - increase to control level, 24h - fall to 86%, after 48h small increase to 93% relatively control. Dose 9.287 C/kg. Large hemispheres. 1h - sharp fall of Mg, Ca-ATPase activity to 67 % relatively control, increase of activity to 96% after 3h and sharp fall of activity to 64% 6h after action of irradiation. Dose 9.287 C/kg. Cerebellum. 1h - sharp decrease of ATPase activity to 80%. After 3h -sharp increase to 160% relatively control level and sharp fall of ATPase activity to 47% relatively control after 6h. The mechanism of radiation pathology of active ion transport has been discussed

  20. Interstitial Fe in MgO

    CERN Document Server

    Mølholt, T E; Gunnlaugsson, H P; Svane, A; Masenda, H; Naidoo, D; Bharuth-Ram, K; Fanciulli, M; Gislason, H P; Johnston, K; Langouche, G; Ólafsson, S; Sielemann, R; Weyer, G

    2014-01-01

    Isolated Fe-57 atoms were studied in MgO single-crystals by emission Mossbauer spectroscopy following implantation of Mn-57 decaying to Fe-57. Four Mossbauer spectral components were found corresponding to different Fe lattice positions and/or charge states. Two components represent Fe atoms substituting Mg as Fe2+ and Fe3+, respectively; a third component is due to Fe in a strongly implantation-induced disturbed region. The fourth component, which is the focus of this paper, can be assigned to Fe at an interstitial site. Comparison of its measured isomer shift with ab initio calculations suggests that the interstitial Fe is located on, or close to, the face of the rock-salt MgO structure. To harmonize such an assignment with the measured near-zero quadrupole interaction a local motion process (cage motion) of the Fe has to be stipulated. The relation of such a local motion as a starting point for long range diffusion is discussed.

  1. Wheat yield dynamics: a structural econometric analysis.

    Science.gov (United States)

    Sahin, Afsin; Akdi, Yilmaz; Arslan, Fahrettin

    2007-10-15

    In this study we initially have tried to explore the wheat situation in Turkey, which has a small-open economy and in the member countries of European Union (EU). We have observed that increasing the wheat yield is fundamental to obtain comparative advantage among countries by depressing domestic prices. Also the changing structure of supporting schemes in Turkey makes it necessary to increase its wheat yield level. For this purpose, we have used available data to determine the dynamics of wheat yield by Ordinary Least Square Regression methods. In order to find out whether there is a linear relationship among these series we have checked each series whether they are integrated at the same order or not. Consequently, we have pointed out that fertilizer usage and precipitation level are substantial inputs for producing high wheat yield. Furthermore, in respect for our model, fertilizer usage affects wheat yield more than precipitation level.

  2. Biogas and Methane Yield from Rye Grass

    Directory of Open Access Journals (Sweden)

    Tomáš Vítěz

    2015-01-01

    Full Text Available Biogas production in the Czech Republic has expanded substantially, including marginal regions for maize cultivation. Therefore, there are increasingly sought materials that could partially replace maize silage, as a basic feedstock, while secure both biogas production and its quality.Two samples of rye grass (Lolium multiflorum var. westerwoldicum silage with different solids content 21% and 15% were measured for biogas and methane yield. Rye grass silage with solid content of 15% reached an average specific biogas yield 0.431 m3·kg−1 of organic dry matter and an average specific methane yield 0.249 m3·kg−1 of organic dry matter. Rye grass silage with solid content 21% reached an average specific biogas yield 0.654 m3·kg−1 of organic dry matter and an average specific methane yield 0.399 m3·kg−1 of organic dry matter.

  3. The HADES-RICH upgrade using Hamamatsu H12700 MAPMTs with DiRICH FEE + Readout

    Science.gov (United States)

    Patel, V.; Traxler, M.

    2018-03-01

    The High Acceptance Di-Electron Spectrometer (HADES) is operational since the year 2000 and uses a hadron blind RICH detector for electron identification. The RICH photon detector is currently replaced by Hamamatsu H12700 MAPMTs with a readout system based on the DiRICH front-end module. The electronic readout chain is being developed as a joint effort of the HADES-, CBM- and PANDA collaborations and will also be used in the photon detectors for the upcoming Compressed Baryonic Matter (CBM) and PANDA experiments at FAIR . This article gives a brief overview on the photomultipliers and their quality assurance test measurements, as well as first measurements of the new DiRICH front-end module in final configurations.

  4. Reducing Mg acceptor activation-energy in Al(0.83)Ga(0.17)N disorder alloy substituted by nanoscale (AlN)₅/(GaN)₁ superlattice using Mg(Ga) δ-doping: Mg local-structure effect.

    Science.gov (United States)

    Zhong, Hong-xia; Shi, Jun-jie; Zhang, Min; Jiang, Xin-he; Huang, Pu; Ding, Yi-min

    2014-10-23

    Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al(0.83)Ga(0.17)N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al(0.83)Ga(0.17)N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 10(19) cm(-3) can be obtained in (AlN)5/(GaN)1 SL by Mg(Ga) δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

  5. Reducing Mg Acceptor Activation-Energy in Al0.83Ga0.17N Disorder Alloy Substituted by Nanoscale (AlN)5/(GaN)1 Superlattice Using MgGa δ-Doping: Mg Local-Structure Effect

    Science.gov (United States)

    Zhong, Hong-Xia; Shi, Jun-Jie; Zhang, Min; Jiang, Xin-He; Huang, Pu; Ding, Yi-Min

    2014-10-01

    Improving p-type doping efficiency in Al-rich AlGaN alloys is a worldwide problem for the realization of AlGaN-based deep ultraviolet optoelectronic devices. In order to solve this problem, we calculate Mg acceptor activation energy and investigate its relationship with Mg local structure in nanoscale (AlN)5/(GaN)1 superlattice (SL), a substitution for Al0.83Ga0.17N disorder alloy, using first-principles calculations. A universal picture to reduce acceptor activation energy in wide-gap semiconductors is given for the first time. By reducing the volume of the acceptor local structure slightly, its activation energy can be decreased remarkably. Our results show that Mg acceptor activation energy can be reduced significantly from 0.44 eV in Al0.83Ga0.17N disorder alloy to 0.26 eV, very close to the Mg acceptor activation energy in GaN, and a high hole concentration in the order of 1019 cm-3 can be obtained in (AlN)5/(GaN)1 SL by MgGa δ-doping owing to GaN-monolayer modulation. We thus open up a new way to reduce Mg acceptor activation energy and increase hole concentration in Al-rich AlGaN.

  6. Di-lepton yield from the decay of excited 28Si states

    International Nuclear Information System (INIS)

    Bacelar, J.C.; Buda, A.; Balanda, A.; Krasznahorkay, A.; Ploeg, H. van der; Sujkowski, Z.; Woude, A. van der

    1994-01-01

    The first dilepton yield measurements from excited nuclear states obtained with a new Positron-Electron Pair Spectroscopic Instrument (PEPSI) are reported. Nuclear states in 28 Si, with an initial excitation energy E * =50 MeV, were populated via the isospin T=0 reaction 4 He+ 24 Mg and the mixed-isospin 3 He+ 25 Mg reaction. In both reactions the dilepton (e + e - ) and photon decay yields were measured concurrently. An excess of counts in the e + e - spectrum, over the converted photon yield, is observed in the energy region above 15 MeV. An analyses is discussed whereby the observed excess counts are assumed to represent the isoscalar E0 strength in excited nuclear states. (orig.)

  7. IMPACT OF A REVISED {sup 25}Mg(p, {gamma}){sup 26}Al REACTION RATE ON THE OPERATION OF THE Mg-Al CYCLE

    Energy Technology Data Exchange (ETDEWEB)

    Straniero, O.; Cristallo, S. [INAF-Osservatorio Astronomico di Collurania, Teramo (Italy); Imbriani, G.; DiLeva, A.; Limata, B. [INFN Sezione di Napoli, Napoli (Italy); Strieder, F. [Institut fuer Experimentalphysik, Ruhr-Universitaet Bochum, Bochum (Germany); Bemmerer, D. [Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstr. 400 (Germany); Broggini, C.; Caciolli, A. [Istituto Nazionale di Fisica Nucleare (INFN), Sezione di Padova, via Marzolo 8, I-35131 Padova (Italy); Corvisiero, P.; Costantini, H.; Lemut, A. [Universita di Genova and INFN Sezione di Genova, Genova (Italy); Formicola, A.; Gustavino, C.; Junker, M. [INFN, Laboratori Nazionali del Gran Sasso (LNGS), Assergi (AQ) (Italy); Elekes, Z.; Fueloep, Zs.; Gyuerky, Gy. [Institute of Nuclear Research (ATOMKI), Debrecen (Hungary); Gervino, G. [Dipartimento di Fisica Universita di Torino and INFN Sezione di Torino, Torino (Italy); Guglielmetti, A., E-mail: straniero@oa-teramo.inaf.it [Universita degli Studi di Milano and INFN, Sezione di Milano (Italy); and others

    2013-02-15

    Proton captures on Mg isotopes play an important role in the Mg-Al cycle active in stellar H-burning regions. In particular, low-energy nuclear resonances in the {sup 25}Mg(p, {gamma}){sup 26}Al reaction affect the production of radioactive {sup 26}Al{sup gs} as well as the resulting Mg/Al abundance ratio. Reliable estimations of these quantities require precise measurements of the strengths of low-energy resonances. Based on a new experimental study performed at the Laboratory for Underground Nuclear Astrophysics, we provide revised rates of the {sup 25}Mg(p, {gamma}){sup 26}Al{sup gs} and the {sup 25}Mg(p, {gamma}){sup 26}Al {sup m} reactions with corresponding uncertainties. In the temperature range 50-150 MK, the new recommended rate of {sup 26}Al {sup m} production is up to five times higher than previously assumed. In addition, at T = 100 MK, the revised total reaction rate is a factor of two higher. Note that this is the range of temperature at which the Mg-Al cycle operates in a H-burning zone. The effects of this revision are discussed. Due to the significantly larger {sup 25}Mg(p, {gamma}){sup 26}Al {sup m} rate, the estimated production of {sup 26}Al{sup gs} in H-burning regions is less efficient than previously obtained. As a result, the new rates should imply a smaller contribution from Wolf-Rayet stars to the galactic {sup 26}Al budget. Similarly, we show that the asymptotic giant branch (AGB) extra-mixing scenario does not appear able to explain the most extreme values of {sup 26}Al/{sup 27}Al, i.e., >10{sup -2}, found in some O-rich presolar grains. Finally, the substantial increase of the total reaction rate makes the hypothesis of self-pollution by massive AGBs a more robust explanation for the Mg-Al anticorrelation observed in globular-cluster stars.

  8. Will energy crop yields meet expectations?

    International Nuclear Information System (INIS)

    Searle, Stephanie Y.; Malins, Christopher J.

    2014-01-01

    Expectations are high for energy crops. Government policies in the United States and Europe are increasingly supporting biofuel and heat and power from cellulose, and biomass is touted as a partial solution to energy security and greenhouse gas mitigation. Here, we review the literature for yields of 5 major potential energy crops: Miscanthus spp., Panicum virgatum (switchgrass), Populus spp. (poplar), Salix spp. (willow), and Eucalyptus spp. Very high yields have been achieved for each of these types of energy crops, up to 40 t ha −1  y −1 in small, intensively managed trials. But yields are significantly lower in semi-commercial scale trials, due to biomass losses with drying, harvesting inefficiency under real world conditions, and edge effects in small plots. To avoid competition with food, energy crops should be grown on non-agricultural land, which also lowers yields. While there is potential for yield improvement for each of these crops through further research and breeding programs, for several reasons the rate of yield increase is likely to be slower than historically has been achieved for cereals; these include relatively low investment, long breeding periods, low yield response of perennial grasses to fertilizer, and inapplicability of manipulating the harvest index. Miscanthus × giganteus faces particular challenges as it is a sterile hybrid. Moderate and realistic expectations for the current and future performance of energy crops are vital to understanding the likely cost and the potential of large-scale production. - Highlights: • This review covers Miscanthus, switchgrass, poplar, willow, and Eucalyptus. • High yields of energy crops are typically from small experimental plots. • Field scale yields are lower due to real world harvesting losses and edge effects. • The potential for yield improvement of energy crops is relatively limited. • Expectations must be realistic for successful policies and commercial production

  9. A recently developed bifacial platelet-rich fibrin matrix

    Directory of Open Access Journals (Sweden)

    E Lucarelli

    2010-07-01

    Full Text Available Platelet-rich plasma (PRP is used clinically in liquid or gel form to promote tissue repair. Because of the poor mechanical properties, conventional PRP is often difficult to handle when used in clinical settings and requires secure implantation in a specific site, otherwise when released growth factors could be washed out during an operation. In this study, we analyzed the end product of a recently developed commercially available system (FIBRINET®, which is a dense pliable, platelet-rich fibrin matrix (PRFM. We characterized the mechanical properties of PRFM and tested whether PRFM releases growth factors and whether released factors induce the proliferation of mesenchymal stem cells (MSC. Mechanical properties as well as platelet distribution were evaluated in PRFM. PRFM demonstrated robust mechanical properties, with a tear elastic modulus of 937.3 + 314.6 kPa, stress at a break of 1476.0 + 526.3 kPa, and an elongation at break of 146.3 + 33.8 %. PRFM maintained its mechanical properties throughout the testing process. Microscopic observations showed that the platelets were localized on one side of the matrix. Elevated levels of PDGF-AA, PDGF-AB, EGF, VEGF, bFGF and TGF-β1 were measured in the day 1-conditioned media (CM of PRFM and growth factor levels decreased thereafter. BMP2 and BMP7 were not detectable. MSC culture media supplemented with 20% PRFM-CM stimulated MSC cell proliferation; at 24 and 48 hours the induction of the proliferation was significantly greater than the induction obtained with media supplemented with 20% foetal bovine serum. The present study shows that the production of a dense, physically robust PRFM made through high-speed centrifugation of intact platelets and fibrin in the absence of exogenous thrombin yields a potential tool for accelerating tissue repair.

  10. Performance in space of the AMS-02 RICH detector

    Energy Technology Data Exchange (ETDEWEB)

    Giovacchini, F., E-mail: francesca.giovacchini@cern.ch

    2014-12-01

    AMS-02 was successfully installed on the International Space Station (ISS) in May 2011, to perform precise measurements of galactic cosmic rays in the 100 MV to few TV magnetic rigidity range. Among several specialized sub-detectors, AMS-02 includes a Ring Imaging Cherenkov detector (RICH), which provides a precise measurement of the particle charge and velocity. The Cherenkov light is produced in a radiator made of silica aerogel and sodium fluoride and collected by means of an array of photomultiplier tubes. Since its launch to space, the detector has been taking data without failures; its functionality and data integrity are monitored and show stable response. In order to achieve the optimal detector performance, calibrations have been performed to account for the dependence of the photodetectors response on temperature and for effective non-uniformities in the detector. The knowledge gathered of the photon yield at the percent level resulted in a charge resolution of 0.3 charge units for He and 0.5 charge units for Si ions. The required precision in the measurements of the particle velocity at the per mil level demanded a more accurate determination of the aerogel refractive index. A map of the aerogel radiator refractive index has been directly inferred from in-flight high statistics data with a precision of Δn/n<2×10{sup −5} on average and its stability with time has also been checked. Finally, a velocity resolution of ∼0.8×10{sup −3} for He and ∼0.5×10{sup −3} for Z>5 ions has been obtained. - Highlights: • AMS-02 RICH detector is fully operational in space and monitored from ground. • Detector calibration for t-dependent and t-independent effects is performed. • Aerogel refractive index fine map has been obtained and its stability checked. • Charge and velocity resolution fulfill design requirements.

  11. Prospecting for Energy-Rich Renewable Raw Materials: Agave Leaf Case Study.

    Science.gov (United States)

    Corbin, Kendall R; Byrt, Caitlin S; Bauer, Stefan; DeBolt, Seth; Chambers, Don; Holtum, Joseph A M; Karem, Ghazwan; Henderson, Marilyn; Lahnstein, Jelle; Beahan, Cherie T; Bacic, Antony; Fincher, Geoffrey B; Betts, Natalie S; Burton, Rachel A

    2015-01-01

    Plant biomass from different species is heterogeneous, and this diversity in composition can be mined to identify materials of value to fuel and chemical industries. Agave produces high yields of energy-rich biomass, and the sugar-rich stem tissue has traditionally been used to make alcoholic beverages. Here, the compositions of Agave americana and Agave tequilana leaves are determined, particularly in the context of bioethanol production. Agave leaf cell wall polysaccharide content was characterized by linkage analysis, non-cellulosic polysaccharides such as pectins were observed by immuno-microscopy, and leaf juice composition was determined by liquid chromatography. Agave leaves are fruit-like--rich in moisture, soluble sugars and pectin. The dry leaf fiber was composed of crystalline cellulose (47-50% w/w) and non-cellulosic polysaccharides (16-22% w/w), and whole leaves were low in lignin (9-13% w/w). Of the dry mass of whole Agave leaves, 85-95% consisted of soluble sugars, cellulose, non-cellulosic polysaccharides, lignin, acetate, protein and minerals. Juice pressed from the Agave leaves accounted for 69% of the fresh weight and was rich in glucose and fructose. Hydrolysis of the fructan oligosaccharides doubled the amount of fermentable fructose in A. tequilana leaf juice samples and the concentration of fermentable hexose sugars was 41-48 g/L. In agricultural production systems such as the tequila making, Agave leaves are discarded as waste. Theoretically, up to 4000 L/ha/yr of bioethanol could be produced from juice extracted from waste Agave leaves. Using standard Saccharomyces cerevisiae strains to ferment Agave juice, we observed ethanol yields that were 66% of the theoretical yields. These data indicate that Agave could rival currently used bioethanol feedstocks, particularly if the fermentation organisms and conditions were adapted to suit Agave leaf composition.

  12. Prospecting for Energy-Rich Renewable Raw Materials: Agave Leaf Case Study.

    Directory of Open Access Journals (Sweden)

    Kendall R Corbin

    Full Text Available Plant biomass from different species is heterogeneous, and this diversity in composition can be mined to identify materials of value to fuel and chemical industries. Agave produces high yields of energy-rich biomass, and the sugar-rich stem tissue has traditionally been used to make alcoholic beverages. Here, the compositions of Agave americana and Agave tequilana leaves are determined, particularly in the context of bioethanol production. Agave leaf cell wall polysaccharide content was characterized by linkage analysis, non-cellulosic polysaccharides such as pectins were observed by immuno-microscopy, and leaf juice composition was determined by liquid chromatography. Agave leaves are fruit-like--rich in moisture, soluble sugars and pectin. The dry leaf fiber was composed of crystalline cellulose (47-50% w/w and non-cellulosic polysaccharides (16-22% w/w, and whole leaves were low in lignin (9-13% w/w. Of the dry mass of whole Agave leaves, 85-95% consisted of soluble sugars, cellulose, non-cellulosic polysaccharides, lignin, acetate, protein and minerals. Juice pressed from the Agave leaves accounted for 69% of the fresh weight and was rich in glucose and fructose. Hydrolysis of the fructan oligosaccharides doubled the amount of fermentable fructose in A. tequilana leaf juice samples and the concentration of fermentable hexose sugars was 41-48 g/L. In agricultural production systems such as the tequila making, Agave leaves are discarded as waste. Theoretically, up to 4000 L/ha/yr of bioethanol could be produced from juice extracted from waste Agave leaves. Using standard Saccharomyces cerevisiae strains to ferment Agave juice, we observed ethanol yields that were 66% of the theoretical yields. These data indicate that Agave could rival currently used bioethanol feedstocks, particularly if the fermentation organisms and conditions were adapted to suit Agave leaf composition.

  13. Electronic structure of ferromagnet-insulator interfaces: Fe/MgO and Co/MgO

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, M.

    2007-07-11

    In this thesis the electronic structure of Fe/MgO{sub x} and Co/MgO{sub x} ferromagnet-insulator interfaces, representing material systems which are widely used in magnetic tunnel junctions, is studied by means of spin- and angle-resolved photoemission spectroscopy. The photoemission studies focus particularly on the response of the ferromagnetic electronic system in contact with MgO of varying stoichiometries, as this reflects the mechanisms of metal-oxide bonding at real ferromagnet-insulator interfaces. The correlation between chemical bonding and electronic structure formation is analyzed by combining information from core- and valence-band photoemission spectroscopy. The spectral features are compared to band structure calculations, which are performed using the SPR-KKR method. The Fe/MgO and Co/MgO systems are prepared by molecular beam epitaxy under ultrahigh vacuum conditions on well-defined (4 x 6) GaAs(001) substrates. A structural analysis by means of low-energy electron diffraction (LEED) reveals their body-centered cubic crystalline structure, whereas the chemical characterization by Auger electron spectroscopy is used to quantify the chemical environment at the sample surfaces. The magnetic analysis, using the magneto-optical Kerr effect, reveals the uniaxial anisotropy of the ferromagnetic layers. A crucial parameter is given by the MgO degree of oxidation, which is addressed by means of core-level spectroscopy and quantified by suitable fitting procedures of the Mg 2p core level. The results of the photoemission experiments show, that the electronic structure of the Fe/MgO and Co/MgO ferromagnet/insulator interfaces and, consequently, the interfacial spin polarization are sensitively controlled by the interface chemistry. In particular, three distinct scenarios are identified: the nearly stoichiometric, the oxygen-deficient and the over-oxidized ferromagnet/MgO interface. Each case is defined by innate characteristics of the electronic structure at

  14. Structure and optical properties of cored wurtzite (Zn,Mg)O heteroepitaxial nanowires

    International Nuclear Information System (INIS)

    Heo, Y.W.; Abernathy, C.; Pruessner, K.; Sigmund, W.; Norton, D.P.; Overberg, M.; Ren, F.; Chisholm, M.F.

    2004-01-01

    The synthesis, structure, and optical properties of one-dimensional heteroepitaxial cored (Zn,Mg)O semiconductor nanowires grown by a catalyst-driven molecular beam epitaxy technique are discussed. The structures form spontaneously in a Zn, Mg and O 2 /O 3 flux, consisting of a single crystal, Zn-rich Zn 1-x Mg x O(x 1-y Mg y O(y>>0.02) sheath. High resolution Z-contrast scanning transmission electron microscopy shows core diameters as small as 4 nm. The cored structure forms spontaneously under constant flux due to a bimodal growth mechanism in which the core forms via bulk like vapor-liquid-solid growth, while the outer sheath grows as a heteroepitaxial layer. Temperature-dependent photoluminescence shows a slight blueshift in the near band edge peak, which is attributed to a few percent Mg doping in the nanoscale ZnO core. The catalyst-driven molecular beam epitaxy technique provides for site-specific nanorod growth on arbitrary substrates

  15. Site preference of Mg acceptors and improvement of p-type doping efficiency in nitride alloys.

    Science.gov (United States)

    Park, Ji-Sang; Chang, K J

    2013-06-19

    We perform first-principles density functional calculations to investigate the effect of Al and In on the formation energy and acceptor level of Mg in group-III nitride alloys. Our calculations reveal a tendency for the Mg dopants to prefer to occupy the lattice sites surrounded with Al atoms, whereas hole carriers are generated in In- or Ga-rich sites. The separation of the Mg dopants and hole carriers is energetically more favourable than a random distribution of dopants, being attributed to the local bonding effect of weak In and strong Al potentials in alloys. As a consequence, the Mg acceptor level, which represents the activation energy of Mg, tends to decrease with increasing numbers of Al next-nearest neighbours, whereas it increases as the number of In next-nearest neighbours increases. Based on the results, we suggest that the incorporation of higher Al and lower In compositions will improve the p-type doping efficiency in quaternary alloys, in comparison with GaN or AlGaN ternary alloys with similar band gaps.

  16. Reproducible increased Mg incorporation and large hole concentration in GaN using metal modulated epitaxy

    International Nuclear Information System (INIS)

    Burnham, Shawn D.; Doolittle, W. Alan; Namkoong, Gon; Look, David C.; Clafin, Bruce

    2008-01-01

    The metal modulated epitaxy (MME) growth technique is reported as a reliable approach to obtain reproducible large hole concentrations in Mg-doped GaN grown by plasma-assisted molecular-beam epitaxy on c-plane sapphire substrates. An extremely Ga-rich flux was used, and modulated with the Mg source according to the MME growth technique. The shutter modulation approach of the MME technique allows optimal Mg surface coverage to build between MME cycles and Mg to incorporate at efficient levels in GaN films. The maximum sustained concentration of Mg obtained in GaN films using the MME technique was above 7x10 20 cm -3 , leading to a hole concentration as high as 4.5x10 18 cm -3 at room temperature, with a mobility of 1.1 cm 2 V -1 s -1 and a resistivity of 1.3 Ω cm. At 580 K, the corresponding values were 2.6x10 19 cm -3 , 1.2 cm 2 V -1 s -1 , and 0.21 Ω cm, respectively. Even under strong white light, the sample remained p-type with little change in the electrical parameters

  17. Reproducible increased Mg incorporation and large hole concentration in GaN using metal modulated epitaxy

    Science.gov (United States)

    Burnham, Shawn D.; Namkoong, Gon; Look, David C.; Clafin, Bruce; Doolittle, W. Alan

    2008-07-01

    The metal modulated epitaxy (MME) growth technique is reported as a reliable approach to obtain reproducible large hole concentrations in Mg-doped GaN grown by plasma-assisted molecular-beam epitaxy on c-plane sapphire substrates. An extremely Ga-rich flux was used, and modulated with the Mg source according to the MME growth technique. The shutter modulation approach of the MME technique allows optimal Mg surface coverage to build between MME cycles and Mg to incorporate at efficient levels in GaN films. The maximum sustained concentration of Mg obtained in GaN films using the MME technique was above 7×1020cm-3, leading to a hole concentration as high as 4.5×1018cm-3 at room temperature, with a mobility of 1.1cm2V-1s-1 and a resistivity of 1.3Ωcm. At 580K, the corresponding values were 2.6×1019cm-3, 1.2cm2V-1s-1, and 0.21Ωcm, respectively. Even under strong white light, the sample remained p-type with little change in the electrical parameters.

  18. RICH Detector for Jefferson Labs CLAS12

    Science.gov (United States)

    Trotta, Richard; Torisky, Ben; Benmokhtar, Fatiha

    2015-10-01

    Jefferson Lab (Jlab) is performing a large-scale upgrade to its Continuous Electron Beam Accelerator Facility (CEBAF) up to 12GeV beams. The Large Acceptance Spectrometer (CLAS12) in Hall B is being upgraded and a new hybrid Ring Imaging Cherenkov (RICH) detector is being developed to provide better kaon - pion separation throughout the 3 to 8 GeV/c momentum range. This detector will be used for a variety of Semi-Inclusive Deep Inelastic Scattering experiments. Cherenkov light can be accurately detected by a large array of sophisticated Multi-Anode Photomultiplier Tubes (MA-PMT) and heavier particles, like kaons, will span the inner radii. We are presenting our work on the creation of the RICH's geometry within the CLAS12 java framework. This development is crucial for future calibration, reconstructions and analysis of the detector.

  19. Climate Variability and Sugarcane Yield in Louisiana.

    Science.gov (United States)

    Greenland, David

    2005-11-01

    This paper seeks to understand the role that climate variability has on annual yield of sugarcane in Louisiana. Unique features of sugarcane growth in Louisiana and nonclimatic, yield-influencing factors make this goal an interesting and challenging one. Several methods of seeking and establishing the relations between yield and climate variables are employed. First, yield climate relations were investigated at a single research station where crop variety and growing conditions could be held constant and yield relations could be established between a predominant older crop variety and a newer one. Interviews with crop experts and a literature survey were used to identify potential climatic factors that control yield. A statistical analysis was performed using statewide yield data from the American Sugar Cane League from 1963 to 2002 and a climate database. Yield values for later years were adjusted downward to form an adjusted yield dataset. The climate database was principally constructed from daily and monthly values of maximum and minimum temperature and daily and monthly total precipitation for six cooperative weather-reporting stations representative of the area of sugarcane production. The influence of 74 different, though not independent, climate-related variables on sugarcane yield was investigated. The fact that a climate signal exists is demonstrated by comparing mean values of the climate variables corresponding to the upper and lower third of adjusted yield values. Most of these mean-value differences show an intuitively plausible difference between the high- and low-yield years. The difference between means of the climate variables for years corresponding to the upper and lower third of annual yield values for 13 of the variables is statistically significant at or above the 90% level. A correlation matrix was used to identify the variables that had the largest influence on annual yield. Four variables [called here critical climatic variables (CCV

  20. Ring recognition in the CBM RICH detector

    International Nuclear Information System (INIS)

    Lebedev, S.; Ososkov, G.; Hoehne, C.

    2007-01-01

    Two algorithms of ring recognition, a standalone ring finder (using only RICH information) and an algorithm based on the information from vertex tracks are described. The fake ring problem and its solution using a set of two-dimensional cuts or an artificial neural network are discussed. Results of a comparative study are given. All developed algorithms were tested on large statistics of simulated events and were then included into the CBM framework for common use

  1. Proton radioactivity from proton-rich nuclei

    International Nuclear Information System (INIS)

    Guzman, F.; Goncalves, M.; Tavares, O.A.P.; Duarte, S.B.; Garcia, F.; Rodriguez, O.

    1999-03-01

    Half-lives for proton emission from proton-rich nuclei have been calculated by using the effective liquid drop model of heavy-particle decay of nuclei. It is shown that this model is able to offer results or spontaneous proton-emission half-life-values in excellent agreement with the existing experimental data. Predictions of half-life-values for other possible proton-emission cases are present for null orbital angular momentum. (author)

  2. Comparison of hydrogen storage properties of pure Mg and milled ...

    Indian Academy of Sciences (India)

    Administrator

    increase the hydriding and dehydriding rates, pure Mg was ground under hydrogen atmosphere (reactive .... Hydrogen storage properties of pure Mg and milled pure Mg. 833. Figure 3. ... elongated and flat shapes via collisions with the steel.

  3. Nutrient Uptake by High-Yielding Cotton Crop in Brazil

    Directory of Open Access Journals (Sweden)

    José Luís Vilela Vieira

    2018-02-01

    Full Text Available ABSTRACT: Determining nutrient uptake and accumulation rates by cotton crops is important to define management strategies, especially for transgenic varieties, which are cultivated using high-technology approaches that require substantial investment to maximize yield. Currently in Brazil, the states of Bahia and Mato Grosso are responsible for 84.4 % of the total cotton growing area. In the present study, two trials were conducted in 2013, one that involved planting FM 940 GLT, FM 980 GLT, and FM 913 GLT varieties in the state of Bahia and the other which involved FM 940 GLT and FM 980 GLT varieties in the state of Mato Grosso. The aim of the two trials was to represent the two regions that currently encompass the largest areas of cotton cultivation. Tissue samples, consisting of leaves, stems, and reproductive components, were collected eleven times during the crop cycle for determination of nutrient content and shoot dry matter. After weighing, plant tissue samples were dried and ground to determine nutrient contents. Because there were no overall differences in nutrient contents and biomass accumulation of the varieties during the crop cycle, we undertook joint analysis of the data from all varieties at each site. Favorable climatic conditions in Bahia promoted plant biomass production that was twice as much as plants grown in Mato Grosso, with cotton yields of 6.2 and 3.8 t ha−1 of lint and seed, respectively. The maximum nutrient accumulation occurred between 137-150 days after emergence (DAE for N; 143-148 for P; 172-185 for K; 100 for Ca; 144-149 for Mg; and 153-158 for S. Maximum uptake ranged from 218-362 kg ha−1 N; 26-53 kg ha−1 P; 233-506 kg ha−1 K; 91-202 kg ha−1 Ca; 28-44 kg ha−1 Mg; and 19-61 kg ha−1 S. On average, the sites revealed nutrient export of 14, 2, 23, 3, 2, and 2 kg t−1 of lint and seed for N, P, K, Ca, Mg, and S, respectively, with little variation among sites. Extraction of nutrients per area by cotton

  4. Microstructure and mechanical property of dual-directional-extruded Mg alloy AZ31

    International Nuclear Information System (INIS)

    Lu Liwei; Liu Tianmo; Jiang Shan; Pan Fushen; Liu Qing; Wang Zhongchang

    2010-01-01

    We report microstructure evolution and mechanical property of Mg alloy AZ31 processed by a new deformation technique, dual-directional extrusion (DDE). Using optical microscopy, scanning electron microscopy, and electron back scatter diffraction technique, we attribute the significant refinement of original coarse grains in the DDE-processed alloy to the occurrence of dynamic recrystallization. Moreover, we find that low temperature is crucial for yielding fine grain, which consequently results in high micro-hardness and yield stress, large fracture strain, and enhanced elongation. The improved mechanical properties are comparable or even superior to those of the alloy subjected to other deformation techniques, rendering the DDE a promising way for further tailoring properties of Mg-based alloys.

  5. Effects of phosphorus and zinc applications on the yields and yields ...

    African Journals Online (AJOL)

    Effects of phosphorus and zinc applications on the yields and yields components of sole early maturing maize ( Zea mays ) and bambaranut ( Vigna subterranean Thour. ) and in intercrop under southern guinea savannah ecology zone.

  6. Yield and competition in barley variety mixtures

    Directory of Open Access Journals (Sweden)

    Kari Jokinen

    1991-09-01

    Full Text Available Competition between spring barley varieties and yield performance of two-, three and four-variety mixtures were studied in two replacement series field experiments. In the first experiment, repeated in three successive years (1983 —85 the components were the six-row varieties Agneta, Arra, Hja-673 and Porno. In the second experiment (1984, including two nitrogen doses (50 and 100 kgN/ha, both six-row (Agneta, Pomo and two-row (Ida, Kustaa varieties were used. Arra in the first and Agneta in the second experiment were the most competitive varieties. The results suggested that the fast growth of Arra at the beginning promoted its competitive ability. Increase in available nitrogen usually strengthened the competitiveness of Agneta. The observed competitive differences between varieties were not related to the earliness of a variety, neither to the morphological characters (two- and six-row varieties nor to the grain yield of a variety grown alone. The competitive ability was not always a stable character, the dominant suppression relationship varying from one environment to another (e.g. growing season, nitrogen dose. The observed overyielding was not statistically significant. The ratio of actual to expected yield and the relative yield total of several mixtures exceeded slightly one. As a conclusion, the yield advantage of mixtures was marginal. As a rule, the mixtures were not more stable than monocultures as determined by the coefficient of variation. However, the yield of some mixtures varied less than the yield of the most stable monoculture.

  7. Superconductivity of powder-in-tube MgB{sub 2} wires

    Energy Technology Data Exchange (ETDEWEB)

    Glowacki, B A; Evetts, J E [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Majoros, M [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Institute of Electrical Engineering, Slovak Academy of Science, Dubravska Cesta 9, Bratislava (Slovakia); Vickers, M [Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Shi, Y [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); McDougall, I [Oxford Instruments Plc, Eynsham, OX8 ITL (United Kingdom)

    2001-04-01

    A new class of 'powder-in-tube' Mg-B superconducting conductors has been prepared using two different methods: an in situ technique where an Mg + 2B mixture was used as a central conductor core and reacted in situ to form MgB{sub 2}, and an ex situ technique where fully reacted MgB{sub 2} powder was used to fill the metal tube. Conductors were prepared using silver, copper and bimetallic silver/stainless steel tubes. Wires manufactured by the in situ technique, diffusing Mg to B particles experienced {approx}25.5% decrease in density from the initial value after cold deformation, due to the phase transformation from Mg + 2({beta}-B){yields}MgB{sub 2} all with hexagonal structure. A comparative study of the intergranular current and grain connectivity in wires was conducted by AC susceptibility measurements and direct four point transport measurements. Using a SQUID magnetometer, magnetization versus magnetic field (M-H) curves of the round wires before and after sintering and reactive diffusion were measured at 5 K and in magnetic fields up to 5 T to define the J{sub cmag}. The direct current measurements were performed in self field at 4.2 K. A comparison between zero-field-cooled (ZFC) and field-cooled (FC) susceptibility measurements for sintered Ag/MgB{sub 2}, and reacted Cu/Mg + 2B conductors revealed systematic differences in the flux pinning in the wires which is in very good agreement with direct high transport current measurements. (author)

  8. Superconductivity of powder-in-tube MgB{sub 2} wires

    Energy Technology Data Exchange (ETDEWEB)

    Glowacki, B.A.; Evetts, J.E. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Majoros, M. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); Institute of Electrical Engineering, Slovak Academy of Science, Dubravska Cesta 9, Bratislava (Slovakia); Vickers, M. [Department of Materials Science and Metallurgy, Pembroke Street, Cambridge, CB2 3QZ (United Kingdom); Shi, Y. [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge, CB3 OHE (United Kingdom); McDougall, I. [Oxford Instruments Plc, Eynsham, OX8 ITL (United Kingdom)

    2001-04-01

    A new class of 'powder-in-tube' Mg-B superconducting conductors has been prepared using two different methods: an in situ technique where an Mg + 2B mixture was used as a central conductor core and reacted in situ to form MgB{sub 2}, and an ex situ technique where fully reacted MgB{sub 2} powder was used to fill the metal tube. Conductors were prepared using silver, copper and bimetallic silver/stainless steel tubes. Wires manufactured by the in situ technique, diffusing Mg to B particles experienced {approx}25.5% decrease in density from the initial value after cold deformation, due to the phase transformation from Mg + 2({beta}-B){yields}MgB{sub 2} all with hexagonal structure. A comparative study of the intergranular current and grain connectivity in wires was conducted by AC susceptibility measurements and direct four point transport measurements. Using a SQUID magnetometer, magnetization versus magnetic field (M-H) curves of the round wires before and after sintering and reactive diffusion were measured at 5 K and in magnetic fields up to 5 T to define the J{sub cmag}. The direct current measurements were performed in self field at 4.2 K. A comparison between zero-field-cooled (ZFC) and field-cooled (FC) susceptibility measurements for sintered Ag/MgB{sub 2}, and reacted Cu/Mg + 2B conductors revealed systematic differences in the flux pinning in the wires which is in very good agreement with direct high transport current measurements. (author)

  9. Discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys as anodes for Mg-air battery

    International Nuclear Information System (INIS)

    Wang, Naiguang; Wang, Richu; Peng, Chaoqun; Peng, Bing; Feng, Yan; Hu, Chengwang

    2014-01-01

    Highlights: • We investigate the effect of indium on the discharge behaviour of Mg-Al-Pb alloy. • We evaluate the performance of Mg-air batteries with Mg-Al-Pb and Mg-Al-Pb-In anodes. • We analyze the activation mechanism of Mg-Al-Pb-In alloy in the discharge process. - Abstract: The discharge behaviour of Mg-Al-Pb and Mg-Al-Pb-In alloys in 3.5 wt.% NaCl solution is investigated by electrochemical techniques, and compared with that of pure magnesium. The results show that Mg-Al-Pb-In alloy provides a more negative potential and exhibits a higher utilization efficiency in contrast with Mg-Al-Pb alloy and pure magnesium during the half-cell test at a large current density, and gives desirable discharge performance when used as anode for Mg- air battery. The peak power density of the Mg-air battery with Mg-Al-Pb-In anode is 94.5 mW cm −2 , which is comparable with those of Mg-H 2 O 2 semi-fuel batteries. Moreover, the activation mechanism of Mg-Al-Pb-In alloy during the discharge process is also analyzed

  10. Proton resonance elastic scattering of $^{30}$Mg for single particle structure of $^{31}$Mg

    CERN Multimedia

    The single particle structure of $^{31}$Mg, which is located in the so-called “island of inversion”, will be studied through measuring Isobaric Analog Resonances (IARs) of bound states of $^{31}$Mg. They are located in the high excitation energy of $^{31}$Al. We are going to determine the spectroscopic factors and angular momenta of the parent states by measuring the excitation function of the proton resonance elastic scattering around 0 degrees in the laboratory frame with around 3 MeV/nucleon $^{30}$Mg beam. The present study will reveal the shell evolution around $^{32}$Mg. In addition, the spectroscopic factor of the (7/2)$^{−}$ state which was not yet determined experimentally, may allow one to study the shape coexistence in this nucleus.

  11. Applications of thermodynamic calculations to Mg alloy design: Mg-Sn based alloy development

    International Nuclear Information System (INIS)

    Jung, In-Ho; Park, Woo-Jin; Ahn, Sang Ho; Kang, Dae Hoon; Kim, Nack J.

    2007-01-01

    Recently an Mg-Sn based alloy system has been investigated actively in order to develop new magnesium alloys which have a stable structure and good mechanical properties at high temperatures. Thermodynamic modeling of the Mg-Al-Mn-Sb-Si-Sn-Zn system was performed based on available thermodynamic, phase equilibria and phase diagram data. Using the optimized database, the phase relationships of the Mg-Sn-Al-Zn alloys with additions of Si and Sb were calculated and compared with their experimental microstructures. It is shown that the calculated results are in good agreement with experimental microstructures, which proves the applicability of thermodynamic calculations for new Mg alloy design. All calculations were performed using FactSage thermochemical software. (orig.)

  12. Green emission from ZnO–MgO nanocomposite due to Mg diffusion at the interface

    International Nuclear Information System (INIS)

    Sowri Babu, K.; Ramachandra Reddy, A.; Venugopal Reddy, K.

    2015-01-01

    The origin and electronic transitions responsible for green emission observed from ZnO–MgO nanocomposite are investigated. The photoluminescence (PL) spectrum of ZnO–MgO nanocomposite annealed at 600 °C showed only a sharp and intense UV emission peak centered at 396 nm. As the annealing temperature increased from 600 °C to 1000 °C, the green emission positioned at 503 nm is emerged and its intensity enhanced gradually and reached maximum value at 900 °C and then decreased at 1000 °C. It is observed that both UV and green emission intensities are enhanced with variation of atomic ratio (Zn/Mg=1.52, 0.50, 0.30, 0.21, 0.15). Our experiments confirmed that the enhancement of green emission intensity is due to the formation of oxygen vacancies (V o ) due to Mg doping at the interface of ZnO and MgO. This experimental observation is in good agreement with the recent theoretical predictions which states that Mg doping in ZnO lowers the formation energies of oxygen vacancies (V o ) and zinc interstitials (Zn i ) significantly. PL excitation and emission spectra analysis reveals that excited state for both UV and green emissions is same and lies 0.24 eV below the conduction band of ZnO. Hence, the green emission is attributed to the transition of an electron form the shallow donor (defect level of Zn i ) to the deep acceptor (defect level of V o ). - Highlights: • It is found that the UV emission intensity from ZnO–MgO nanocomposite enhanced with increase of Mg concentration. • The intensity of the green emission is enhanced gradually as the temperature increased from 600 °C to 900 °C and then decreased at 1000 °C. • The effect of Mg concentration, MgO, strain at the interface on green emission is investigated. • These experiments confirmed that green emission is due to the oxygen vacancies created in ZnO due to the Mg doping at the interface and it is in good agreement with the theoretical predictions. • The decrease of green emission intensity is

  13. Mineralogy and geochemistry of boehmite-rich coals: New insights from the Haerwusu Surface Mine, Jungar Coalfield, Inner Mongolia, China

    Science.gov (United States)

    Dai, S.; Li, D.; Chou, C.-L.; Zhao, L.; Zhang, Y.; Ren, D.; Ma, Y.; Sun, Y.

    2008-01-01

    Boehmite-rich coal of Pennsylvanian age was discovered earlier at the Heidaigou Surface Mine, Jungar Coalfield, Inner Mongolia, China. This paper reports new results on 29 bench samples of the no. 6 coal from a drill core from the adjacent Haerwusu Surface Mine, and provides new insights into the origin of the minerals and elements present. The results show that the proportion of inertinite in the no. 6 coal is higher than in other Late Paleozoic coals in northern China. Based on mineral proportions (boehmite to kaolinite ratio) and major element concentrations in the coal benches of the drill core, the no. 6 coal may be divided into five sections (I to V). Major minerals in Sections I and V are kaolinite. Sections II and IV are mainly kaolinite with a trace of boehmite, and Section III is high in boehmite. The boehmite is derived from bauxite in the weathered surface (Benxi Formation) in the sediment-source region. The no. 6 coal is rich in Al2O3 (8.89%), TiO2 (0.47%), Li (116????g/g), F (286????g/g), Ga (18????g/g), Se (6.1????g/g), Sr (350????g/g), Zr (268????g/g), REEs (172????g/g), Pb (30????g/g), and Th (17????g/g). The elements are classified into five associations by cluster analysis, i.e. Groups A, B, C, D, and E. Group A (ash-SiO2-Al2O3-Na2O-Li) and Group B (REE-Sc-In-Y-K2O-Rb-Zr-Hf-Cs-U-P2O5-Sr-Ba-Ge) are strongly correlated with ash yield and mainly have an inorganic affinity. The elements that are negatively or less strongly correlated with ash yield (with exceptions of Fe2O3, Be, V, and Ni) are grouped in the remaining three associations: Group C, Se-Pb-Hg-Th-TiO2-Bi-Nb-Ta-Cd-Sn; Group D, Co-Mo-Tl-Be-Ni-Sb-MgO-Re-Ga-W-Zn-V-Cr-F-Cu; and Group E, S-As-CaO-MnO-Fe2O3. Aluminum is mainly distributed in boehmite, followed by kaolinite. The high correlation coefficients of the Li-ash, Li-Al2O3, and Li-SiO2 pairs indicate that Li is related to the aluminosilicates in the coal. The boehmite-rich coal is high in gallium and F, which occur in boehmite and the

  14. Benefits of seasonal forecasts of crop yields

    Science.gov (United States)

    Sakurai, G.; Okada, M.; Nishimori, M.; Yokozawa, M.

    2017-12-01

    Major factors behind recent fluctuations in food prices include increased biofuel production and oil price fluctuations. In addition, several extreme climate events that reduced worldwide food production coincided with upward spikes in food prices. The stabilization of crop yields is one of the most important tasks to stabilize food prices and thereby enhance food security. Recent development of technologies related to crop modeling and seasonal weather forecasting has made it possible to forecast future crop yields for maize and soybean. However, the effective use of these technologies remains limited. Here we present the potential benefits of seasonal crop-yield forecasts on a global scale for choice of planting day. For this purpose, we used a model (PRYSBI-2) that can well replicate past crop yields both for maize and soybean. This model system uses a Bayesian statistical approach to estimate the parameters of a basic process-based model of crop growth. The spatial variability of model parameters was considered by estimating the posterior distribution of the parameters from historical yield data by using the Markov-chain Monte Carlo (MCMC) method with a resolution of 1.125° × 1.125°. The posterior distributions of model parameters were estimated for each spatial grid with 30 000 MCMC steps of 10 chains each. By using this model and the estimated parameter distributions, we were able to estimate not only crop yield but also levels of associated uncertainty. We found that the global average crop yield increased about 30% as the result of the optimal selection of planting day and that the seasonal forecast of crop yield had a large benefit in and near the eastern part of Brazil and India for maize and the northern area of China for soybean. In these countries, the effects of El Niño and Indian Ocean dipole are large. The results highlight the importance of developing a system to forecast global crop yields.

  15. Metal-rich fluid inclusions provide new insights into unconformity-related U deposits (Athabasca Basin and Basement, Canada)

    Science.gov (United States)

    Richard, Antonin; Cathelineau, Michel; Boiron, Marie-Christine; Mercadier, Julien; Banks, David A.; Cuney, Michel

    2016-02-01

    The Paleoproterozoic Athabasca Basin (Canada) hosts numerous giant unconformity-related uranium deposits. The scope of this study is to establish the pressure, temperature, and composition (P-T-X conditions) of the brines that circulated at the base of the Athabasca Basin and in its crystalline basement before, during and after UO2 deposition. These brines are commonly sampled as fluid inclusions in quartz- and dolomite-cementing veins and breccias associated with alteration and U mineralization. Microthermometry and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) data from five deposits (Rabbit Lake, P-Patch, Eagle Point, Millennium, and Shea Creek) complement previously published data for the McArthur River deposit. In all of the deposits investigated, fluid inclusion salinity is between 25 and 40 wt.% NaCl equiv., with compositions displaying a continuum between a "NaCl-rich brine" end-member (Cl > Na > Ca > Mg > K) and a "CaCl2-rich brine" end-member (Cl > Ca ≈ Mg > Na > K). The CaCl2-rich brine has the highest salinity and shows evidence for halite saturation at the time of trapping. The continuum of compositions between the NaCl-rich brine and the CaCl2-rich brine end-members combined with P-T reconstructions suggest anisothermal mixing of the two brines (NaCl-rich brine, 180 ± 30 °C and 800 ± 400 bars; CaCl2-rich brine, 120 ± 30 °C and 600 ± 300 bars) that occurred under fluctuating pressure conditions (hydrostatic to supra-hydrostatic). However, because the two brines were U bearing and therefore oxidized, brine mixing was probably not the driving force for UO2 deposition. Several scenarios are put forward to account for the Cl-Na-Ca-Mg-K composition of the brines, involving combinations of seawater evaporation, halite dissolution, mixing with a halite-dissolution brine, Mg/Ca exchange by dolomitization, Na/Ca exchange by albitization of plagioclase, Na/K exchange by albitization of K-feldspar, and Mg loss by Mg-rich

  16. Microstructure, mechanical properties and bio-corrosion properties of Mg-Zn-Mn-Ca alloy for biomedical application

    International Nuclear Information System (INIS)

    Zhang Erlin; Yang Lei

    2008-01-01

    Microstructure, mechanical properties and bio-corrosion properties of as-cast Mg-Zn-Mn-Ca alloys were investigated for biomedical application in detail by optical microscopy, scanning electronic microscopy (SEM), mechanical properties testing and electrochemical measurement. SEM and optical microscopy observation indicated that the grain size of the as-cast alloys significantly decreased with the increasing of Ca content up to 0.5 wt.%. Further increasing of Ca content did not refine the grain more. The phase constitute was mainly controlled by the atomic ratio of Zn to Ca. When the ratio was more than 1.0-1.2, the alloy was mainly composed of primary Mg and lamellar eutectic (α-Mg + Ca 2 Mg 6 Zn 3 ), while the alloy was composed of primary Mg and divorced eutectic (α-Mg + Mg 2 Ca + Ca 2 Mg 6 Zn 3 ) when the atomic ratio was less than 1.0-1.2. The yield strength of the as-cast alloy increased but the elongation and the tensile strength increased first and then decreased with the increasing of Ca content. It was thought that Mg 2 Ca phase deteriorated the tensile strength and ductility. Electrochemical measurements indicated that Mg 2 Ca phase improved the corrosion resistance of the as-cast alloy

  17. Corrosion analysis of AlMg2 and AlMgSi using electrochemical method

    International Nuclear Information System (INIS)

    Dian A; Maman Kartaman; Rosika K; Yanlinastuti

    2014-01-01

    Corrosion test of cladding materials and structures of research reactor fuel, AlMgSi and AlMg2 have been performed in demineralized water of pH 2 and 6.7 using an electrochemical method. Corrosion phenomenon is affected by several factor such as composition and condition of solution. The purpose of this activity is to investigate the corrosion phenomena through the determination of the parameters of corrosion and polarization curve. The materials used are AlMg2 and AlMgSi alloy in circular dish shape with an area of 1 Cm"2. Preparation of the test sample is performed through several stages polishing, cleaning and drying procedures followed ASTM G3. The electrochemical method is done by measuring the open circuit potential (OCP), polarization resistance and potentiodynamic in demineralized water of pH 2 and pH 6.7 at temperature of 25°C. The results of the OCP is the corrosion potential (Ecorr) of AlMg2 and AlMgSi each of -906.1 mV and -619.8 mV at pH 2 and -868.6 and -756.7 mV at pH 6.7 mV. The results of measurements by polarization resistance technique showed that the corrosion rate of AlMg2 and AlMgSi in safe category (<2 mpy) at pH 6.7 and at pH 2 corrosion rate increased significantly, but still in the lightweight category (<20 mpy). Potentiodynamic curves showed that the passivation at pH 6.7 is very low while the passivation at pH 2 occurs within a relatively short range potential and followed events corroded. (author)

  18. Slope Controls Grain Yield and Climatic Yield in Mountainous Yunnan province, China

    Science.gov (United States)

    Duan, X.; Rong, L.; Gu, Z.; Feng, D.

    2017-12-01

    Mountainous regions are increasingly vulnerable to food insecurity because of limited arable land, growing population pressure, and climate change. Development of sustainable mountain agriculture will require an increased understanding of the effects of environmental factors on grain and climatic yields. The objective of this study was to explore the relationships between actual grain yield, climatic yield, and environmental factors in a mountainous region in China. We collected data on the average grain yield per unit area in 119 counties in Yunnan province from 1985 to 2012, and chose 17 environmental factors for the same period. Our results showed that actual grain yield ranged from 1.43 to 6.92 t·ha-1, and the climatic yield ranged from -0.15 to -0.01 t·ha-1. Lower climatic yield but higher grain yield was generally found in central areas and at lower slopes and elevations in the western and southwestern counties of Yunnan province. Higher climatic yield but lower grain yield were found in northwestern parts of Yunnan province on steep slopes. Annual precipation and temperature had a weak influence on the climatic yield. Slope explained 44.62 and 26.29% of the variation in grain yield and climatic yield. The effects of topography on grain and climatic yields were greater than climatic factors. Slope was the most important environmental variable for the variability in climatic and grain yields in the mountainous Yunnan province due to the highly heterogeneous topographic conditions. Conversion of slopes to terraces in areas with higher climatic yields is an effective way to maintain grain production in response to climate variability. Additionally, soil amendments and soil and water conservation measures should be considered to maintain soil fertility and aid in sustainable development in central areas, and in counties at lower slopes and elevations in western and southwestern Yunnan province.

  19. Optimizing rice yields while minimizing yield-scaled global warming potential.

    Science.gov (United States)

    Pittelkow, Cameron M; Adviento-Borbe, Maria A; van Kessel, Chris; Hill, James E; Linquist, Bruce A

    2014-05-01

    To meet growing global food demand with limited land and reduced environmental impact, agricultural greenhouse gas (GHG) emissions are increasingly evaluated with respect to crop productivity, i.e., on a yield-scaled as opposed to area basis. Here, we compiled available field data on CH4 and N2 O emissions from rice production systems to test the hypothesis that in response