WorldWideScience

Sample records for mg dry weight

  1. Changes of micronutrients, dry weight and plant development in ...

    African Journals Online (AJOL)

    User

    2011-05-09

    May 9, 2011 ... This study was carried out to determine the effects of salt stress on the growth, dry weights and micronutrient contents of canola (Brassica napus L.) cultivars grown in greenhouse ... crop productivity in the arid and semiarid regions of the ... fertilizer equivalent to 150 kg ha-1 and triple-superphosphate (80 kg.

  2. Dry cryomagnetic system with MgB2 coil

    Science.gov (United States)

    Abin, D. A.; Mineev, N. A.; Osipov, M. A.; Pokrovskii, S. V.; Rudnev, I. A.

    2017-12-01

    MgB2 may be the future superconducting wire material for industrial magnets due to it’s higher operation temperature and potentially lower cost than low temperature superconductors (LTS) have. We designed a compact cryomagnetic system with the use of MgB2. The possibility of creating a magnet with a central field of 5 T from a commercial MgB2 wire by the “react and wound” method was investigated. The magnetic system is cooled by a cryocooler through a copper bus. The magnet has a warm bore diameter of 4 cm. The design of a magnet consisting of three concentric solenoids is proposed: an internal one of high-temperature superconductor (HTS), an average of MgB2, and an external of NbTi. The operating current of the system is 100 A. Two pairs of current leads are used. A separate pair of current leads for power supplying NbTi coil allows testing of MgB2 and HTS coils in an external field. The load curves for each of the magnets are calculated.

  3. Changes in dimensions and weight of human dentine after different drying procedures and during subsequent rehydration

    NARCIS (Netherlands)

    Van der Graaf, E R; Ten Bosch, J J

    Shrinkage of dentine and the decrease in its weight after drying were measured. Three drying procedures were used, freeze-drying and drying in nitrogen at 60 and 100 degrees C. The dentine was subsequently rehydrated while measuring its dimensions. Rehydrated dentine was weighed. Dentine weight

  4. EFFECT OF ARSENIC ON DRY WEIGHT AND RELATIVE CHLOROPHYLL CONTENT IN GREENINGMAIZE AND SUNFLOWER TISSUES

    Directory of Open Access Journals (Sweden)

    Szilvia Várallyay

    2015-02-01

    Full Text Available Arsenic is one of the most toxic elements that can be found in the environment. Excessive uptake of arsenic may cause physiological changes in plants. The aim of the study was to investigate the effect of different arsenic treatments on relative chlorophyll content and dry weight of shoot and root of maize and sunflower in the early phases of plant development. Seedlings were grown in climatic room in nutrient solution under strictly regulated environmental conditions. The plants were exposed to 3, 10 and 30 mg kg-1arsenic, whereas there was no arsenic treatment on the control plants. We applied arsenic in the form of arsenite (NaAsO2 and arsenate (KH2AsO4, respectively. After 14 days of arsenic treatments, changes in relative chlorophyll content and dry weight of maize shoots and roots were recorded. In the case of sunflower these physiological parameters were measured after 21 day. The applied arsenic decreased the relative chlorophyll content of maize and sunflower leaves, especially at concentration of30 mg kg-1. The increasing amount of As treatment were resulted the lower weight of the experimental plants, which was more considerable in the case of the roots. The results indicate that the sunflower plants is more sensitive to arsenic toxicity than maize plants and all data demonstrate that the As(III is more toxic to these crop plants than the As(V.

  5. BIOIMPEDANCE VECTOR ANALYSIS AS A TOOL FOR DETERMINATION AND ADJUSTMENT OF DRY WEIGHT IN HEMODIALYSIS PATIENTS

    OpenAIRE

    Ximena Atilano; José Luis.Miguel; Jorge Martínez; Rafael Sánchez; Rafael Selgas

    2012-01-01

    The hemodialysis (HD) patient is fluid overloaded, even when there is no apparent edema. Due to this, is vital to know the dry weight. No clinical or laboratory parameters are reliable, simple and accessible for this purpose. The bioelectrical impedance has been applied to estimate body fluids and dry weight. The purpose was to use the bioelectrical vector analysis (BIVA) as a tool to adjust the intensity of ultrafiltration and achievement of dry weight in HD patients. We performed monthly me...

  6. Contribution to the development of dry R and W MgB2 superconducting magnets

    International Nuclear Information System (INIS)

    Pasquet, Raphael

    2015-01-01

    Currently, the majority of superconducting magnets, including MRI, are cooled by a bath of liquid helium at atmospheric pressure. Nevertheless, this type of cooling is expensive and imposes significant security constraints for large volumes. For these reasons, the cooling of superconducting magnets is desirable without liquid helium. Cryo-cooler provides dry cooling to 4 K without any liquid helium. However, the power available is low and dry cooling is difficult. In these conditions, it is complicate to use NbTi with dry cooling. But if we increase the operating temperature to 10 K, the power of cryo-cooler increases by a factor of ten. Nevertheless in this case, it is necessary to use of a high critical temperature superconductor. We choose to use MgB 2 R and W conductors because it is relatively low cost but it has the handicap to be sensible at mechanical stress. It is therefore necessary to be careful during their winding to not degrade their superconducting performance. As part of this thesis, we have developed a dry test facility to measure the critical current of MgB 2 R and W conductors as well as mock-ups. To do this, a new type of thermal contact based on aluminum nitride has been developed. In addition to this development, we designed two MgB 2 R and W magnet mock-ups: a solenoid and a double pancake. The double pancake was manufactured (with a new patented winding method) and it has been successfully tested. (author) [fr

  7. BIOIMPEDANCE VECTOR ANALYSIS AS A TOOL FOR DETERMINATION AND ADJUSTMENT OF DRY WEIGHT IN HEMODIALYSIS PATIENTS

    Directory of Open Access Journals (Sweden)

    Ximena Atilano

    2012-06-01

    Full Text Available The hemodialysis (HD patient is fluid overloaded, even when there is no apparent edema. Due to this, is vital to know the dry weight. No clinical or laboratory parameters are reliable, simple and accessible for this purpose. The bioelectrical impedance has been applied to estimate body fluids and dry weight. The purpose was to use the bioelectrical vector analysis (BIVA as a tool to adjust the intensity of ultrafiltration and achievement of dry weight in HD patients. We performed monthly measurements of bioimpedance in 24 HD patients pre-and post-dialysis for four months. We plotted the patient´s vectors in the RXc graph in order to meet individually hydration status and adjust the dry weight. Nutritional status was evaluated by Bilbrey Index. Adjustment on dry weight, was made in 18 patients, 13 of whom (72% were able to reach it. The postdialysis vectors, migrated to upper quadrants, indicating adequate hydration. Postdialysis vectors at the end of the study were significantly different compared to baseline (Figure 1. Five patients didn´t reach dry weight despite the adjustments, 4 were men with overhydration and 3 of them were severely malnourished. A woman remained dehydrated. In conclusion, the impedance vector analysis is a useful tool for adjusting dry weight in hemodialysis patients.fx1

  8. Liraglutide 3.0 mg for weight management: weight-loss dependent and independent effects.

    Science.gov (United States)

    Bays, Harold; Pi-Sunyer, Xavier; Hemmingsson, Joanna Uddén; Claudius, Birgitte; Jensen, Christine B; Van Gaal, Luc

    2017-02-01

    As an adjunct to a reduced-calorie diet and increased physical activity, treatment with liraglutide 3.0 mg for weight management provides a statistically significant and clinically meaningful weight loss of 5.7%-8.0% compared to 1.6%-2.6% with placebo. The objective of this post hoc analysis was to quantify the relative contribution of weight loss to the treatment effects of liraglutide 3.0 mg on key efficacy endpoints. The analysis utilized data from 4725 participants across three randomized, placebo-controlled, double-blind trials that evaluated the efficacy and safety of liraglutide 3.0 mg versus placebo, as an adjunct to a reduced-calorie diet and increased physical activity (ClinicalTrials.gov identifiers: NCT01272219, NCT01272232 and NCT01557166). The duration of two of the trials was 56 weeks; one trial was of 32 weeks' duration. A mediation analysis was performed, which ranked the relative contribution of weight loss to the treatment effects of liraglutide 3.0 mg on key cardiometabolic efficacy endpoints, Apnea-Hypopnea Index (AHI) and health-related quality of life (QoL). A limitation of this type of analysis is that it cannot conclusively prove a causal relationship. In individuals without type 2 diabetes mellitus (T2DM), endpoints predominantly driven by liraglutide-induced weight loss included waist circumference, diastolic blood pressure, triglycerides, high density lipoprotein cholesterol, AHI, and Impact of Weight on Quality of Life-Lite total and physical function scores. Endpoints predominantly independent of weight loss included the glycemic endpoints hemoglobin A1c and fasting plasma glucose in individuals with and without T2DM. Regardless of the degree of dependence on weight loss according to the mediation analysis, greater weight loss was associated with greater improvement in all endpoints. Treatment with liraglutide 3.0 mg contributes to improved cardiometabolic parameters, AHI and health-related QoL through both weight

  9. Influence of sugars on the dry-weight increase of gamma irradiated Jerusalem artichoke tuber's tissue

    International Nuclear Information System (INIS)

    Schaeverbeke-Sacre, J.

    1976-01-01

    Jerusalem artichoke tuber's explants after a γ irradiation of 6000 rads couldn't proliferate in a growth medium containing glucose and indolyl acetic acid; their dry weight is increased by an accumulation of sugars [fr

  10. A randomized, controlled trial of 3.0 mg of Liraglutide in weight management

    DEFF Research Database (Denmark)

    Pi-Sunyer, Xavier; Astrup, Arne; Fujioka, Ken

    2015-01-01

    Background Obesity is a chronic disease with serious health consequences, but weight loss is difficult to maintain through lifestyle intervention alone. Liraglutide, a glucagon-like peptide-1 analogue, has been shown to have potential benefit for weight management at a once-daily dose of 3.0 mg...... or untreated dyslipidemia or hypertension. We randomly assigned patients in a 2:1 ratio to receive once-daily subcutaneous injections of liraglutide at a dose of 3.0 mg (2487 patients) or placebo (1244 patients); both groups received counseling on lifestyle modification. The coprimary end points were...... with liraglutide were mild or moderate nausea and diarrhea. Serious events occurred in 6.2% of the patients in the liraglutide group and in 5.0% of the patients in the placebo group. Conclusions In this study, 3.0 mg of liraglutide, as an adjunct to diet and exercise, was associated with reduced body weight...

  11. Exposure-response analyses of liraglutide 3.0 mg for weight management.

    Science.gov (United States)

    Wilding, J P H; Overgaard, R V; Jacobsen, L V; Jensen, C B; le Roux, C W

    2016-05-01

    Liraglutide 3.0 mg, an acylated GLP-1 analogue approved for weight management, lowers body weight through decreased energy intake. We conducted exposure-response analyses to provide important information on individual responses to given drug doses, reflecting inter-individual variations in drug metabolism, absorption and excretion. We report efficacy and safety responses across a wide range of exposure levels, using data from one phase II (liraglutide doses 1.2, 1.8, 2.4 and 3.0 mg), and two phase IIIa [SCALE Obesity and Prediabetes (3.0 mg); SCALE Diabetes (1.8; 3.0 mg)] randomized, placebo-controlled trials (n = 4372). There was a clear exposure-weight loss response. Weight loss increased with greater exposure and appeared to level off at the highest exposures associated with liraglutide 3.0 mg in most individuals, but did not fully plateau in men. In individuals with overweight/obesity and comorbid type 2 diabetes, there was a clear exposure-glycated haemoglobin (HbA1c) relationship. HbA1c reduction increased with higher plasma liraglutide concentration (plateauing at ∼21 nM); however, for individuals with baseline HbA1c >8.5%, HbA1c reduction did not fully plateau. No exposure-response relationship was identified for any safety outcome, with the exception of gastrointestinal adverse events (AEs). Individuals with gallbladder AEs, acute pancreatitis or malignant/breast/benign colorectal neoplasms did not have higher liraglutide exposure compared with the overall population. These analyses support the use of liraglutide 3.0 mg for weight management in all subgroups investigated; weight loss increased with higher drug exposure, with no concomitant deterioration in safety/tolerability besides previously known gastrointestinal side effects. © 2016 John Wiley & Sons Ltd.

  12. Exposure–response analyses of liraglutide 3.0 mg for weight management

    Science.gov (United States)

    Overgaard, R. V.; Jacobsen, L. V.; Jensen, C. B.; le Roux, C. W.

    2016-01-01

    Aims Liraglutide 3.0 mg, an acylated GLP‐1 analogue approved for weight management, lowers body weight through decreased energy intake. We conducted exposure‐response analyses to provide important information on individual responses to given drug doses, reflecting inter‐individual variations in drug metabolism, absorption and excretion. Methods We report efficacy and safety responses across a wide range of exposure levels, using data from one phase II (liraglutide doses 1.2, 1.8, 2.4 and 3.0 mg), and two phase IIIa [SCALE Obesity and Prediabetes (3.0 mg); SCALE Diabetes (1.8; 3.0 mg)] randomized, placebo‐controlled trials (n = 4372). Results There was a clear exposure–weight loss response. Weight loss increased with greater exposure and appeared to level off at the highest exposures associated with liraglutide 3.0 mg in most individuals, but did not fully plateau in men. In individuals with overweight/obesity and comorbid type 2 diabetes, there was a clear exposure–glycated haemoglobin (HbA1c) relationship. HbA1c reduction increased with higher plasma liraglutide concentration (plateauing at ∼21 nM); however, for individuals with baseline HbA1c >8.5%, HbA1c reduction did not fully plateau. No exposure–response relationship was identified for any safety outcome, with the exception of gastrointestinal adverse events (AEs). Individuals with gallbladder AEs, acute pancreatitis or malignant/breast/benign colorectal neoplasms did not have higher liraglutide exposure compared with the overall population. Conclusions These analyses support the use of liraglutide 3.0 mg for weight management in all subgroups investigated; weight loss increased with higher drug exposure, with no concomitant deterioration in safety/tolerability besides previously known gastrointestinal side effects. PMID:26833744

  13. Use of the dry-weight-rank method of botanical analysis in the ...

    African Journals Online (AJOL)

    The dry-weight-rank method of botanical analysis was tested in the highveld of the Eastern Transvaal and was found to be an efficient and accurate means of determining the botanical composition of veld herbage. Accuracy was increased by weighting ranks on the basis of quadrat yield, and by allocation of equal ranks to ...

  14. Liraglutide 3.0 mg for Weight Management: A Population Pharmacokinetic Analysis.

    Science.gov (United States)

    Overgaard, Rune V; Petri, Kristin C; Jacobsen, Lisbeth V; Jensen, Christine B

    2016-11-01

    This analysis used a population pharmacokinetic approach to identify covariates that influence plasma exposure of liraglutide 3.0 mg, a glucagon-like peptide-1 (GLP-1) receptor agonist approved for weight management in overweight and obese individuals. Samples for pharmacokinetic analysis were drawn at weeks 2, 12 and 28 of the phase IIIa SCALE Obesity and Prediabetes (N = 2339) and SCALE Diabetes (N = 584) trials. Dose proportionality of liraglutide in obese subjects was investigated using data from a phase II dose-finding study (N = 331). Dose-proportional exposure of liraglutide up to and including 3.0 mg was confirmed. Body weight and sex influenced exposure of liraglutide 3.0 mg, while age ≥70 years, race, ethnicity and baseline glycaemic status did not. Compared with a reference subject weighing 100 kg, exposure of liraglutide 3.0 mg was 44 % lower for a subject weighing 234 kg (90 % CI 41-47), 41 % higher for a subject weighing 60 kg (90 % CI 37-46), and 32 % higher (90 % CI 28-35) in females than males with the same body weight. Neither injection site nor renal function significantly influenced exposure of liraglutide 3.0 mg (post hoc analysis). Population pharmacokinetics of liraglutide up to and including 3.0 mg daily in overweight and obese adults demonstrated dose-proportional exposure, and limited effect of covariates other than sex and body weight. These findings were similar to those previously observed with liraglutide up to 1.8 mg in subjects with type 2 diabetes mellitus. Further analysis of exposure-response relationship and its effect on dose requirements is addressed in a separate publication.

  15. Catalytic performance of Ni/MgO catalyst in methane dry reforming

    Science.gov (United States)

    Al-Swai, Basem M.; Osman, N. B.; Abdullah, Bawadi

    2017-10-01

    Methane dry reforming to synthesis gas over nickel catalysts supported on magnesium oxide has been studied. The support was prepared via co-precipitation method using ammonia solution (20 wt% in water) as the precipitating agent. 10 wt% of Ni metal was impregnated to form Ni/MgO catalyst. The prepared catalyst was characterized by different techniques, such as XRD, BET, SEM, and TGA analysis. The effect of reaction conditions on the conversions of CH4 and CO2, selectivity of H2 and CO, and carbon deposition were investigated in a tabular furnace reactor. The catalyst afforded as high as 93% CH4 conversion at 900 °C. The catalyst has also shown excellent stability during reaction at relatively higher space velocity (1.8×104 ml g-1 h-1) and 800 °C reaction temperature. TGA characterization of spent catalyst has shown lesser magnitude of carbon deposition on the surface of the catalyst at 900 °C.

  16. Self-healing of drying shrinkage cracks in cement-based materials incorporating reactive MgO

    Science.gov (United States)

    Qureshi, T. S.; Al-Tabbaa, A.

    2016-08-01

    Excessive drying shrinkage is one of the major issues of concern for longevity and reduced strength performance of concrete structures. It can cause the formation of cracks in the concrete. This research aims to improve the autogenous self-healing capacity of traditional Portland cement (PC) systems, adding expansive minerals such as reactive magnesium oxide (MgO) in terms of drying shrinkage crack healing. Two different reactive grades (high ‘N50’and moderately high ‘92-200’) of MgO were added with PC. Cracks were induced in the samples with restraining end prisms through natural drying shrinkage over 28 days after casting. Samples were then cured under water for 28 and 56 days, and self-healing capacity was investigated in terms of mechanical strength recovery, crack sealing efficiency and improvement in durability. Finally, microstructures of the healing materials were investigated using FT-IR, XRD, and SEM-EDX. Overall N50 mixes show higher expansion and drying shrinkage compared to 92-200 mixes. Autogenous self-healing performance of the MgO containing samples were much higher compared to control (only PC) mixes. Cracks up to 500 μm were sealed in most MgO containing samples after 28 days. In the microstructural investigations, highly expansive Mg-rich hydro-carbonate bridges were found along with traditional calcium-based, self-healing compounds (calcite, portlandite, calcium silicate hydrates and ettringite).

  17. A Randomized, Controlled Trial of 3.0 mg of Liraglutide in Weight Management.

    Science.gov (United States)

    Pi-Sunyer, Xavier; Astrup, Arne; Fujioka, Ken; Greenway, Frank; Halpern, Alfredo; Krempf, Michel; Lau, David C W; le Roux, Carel W; Violante Ortiz, Rafael; Jensen, Christine Bjørn; Wilding, John P H

    2015-07-02

    Obesity is a chronic disease with serious health consequences, but weight loss is difficult to maintain through lifestyle intervention alone. Liraglutide, a glucagon-like peptide-1 analogue, has been shown to have potential benefit for weight management at a once-daily dose of 3.0 mg, injected subcutaneously. We conducted a 56-week, double-blind trial involving 3731 patients who did not have type 2 diabetes and who had a body-mass index (BMI; the weight in kilograms divided by the square of the height in meters) of at least 30 or a BMI of at least 27 if they had treated or untreated dyslipidemia or hypertension. We randomly assigned patients in a 2:1 ratio to receive once-daily subcutaneous injections of liraglutide at a dose of 3.0 mg (2487 patients) or placebo (1244 patients); both groups received counseling on lifestyle modification. The coprimary end points were the change in body weight and the proportions of patients losing at least 5% and more than 10% of their initial body weight. At baseline, the mean (±SD) age of the patients was 45.1±12.0 years, the mean weight was 106.2±21.4 kg, and the mean BMI was 38.3±6.4; a total of 78.5% of the patients were women and 61.2% had prediabetes. At week 56, patients in the liraglutide group had lost a mean of 8.4±7.3 kg of body weight, and those in the placebo group had lost a mean of 2.8±6.5 kg (a difference of -5.6 kg; 95% confidence interval, -6.0 to -5.1; Pweight (Pweight (Pweight and improved metabolic control. (Funded by Novo Nordisk; SCALE Obesity and Prediabetes NN8022-1839 ClinicalTrials.gov number, NCT01272219.).

  18. Dry sliding wear behaviour of Al-12Si-4Mg alloy with cerium addition

    International Nuclear Information System (INIS)

    Anasyida, A.S.; Daud, A.R.; Ghazali, M.J.

    2010-01-01

    The purpose of this work is to understand the effect of cerium addition on wear resistance behaviour of as-cast alloys. Al-12Si-4 Mg alloys with 1-5 wt% cerium addition were prepared using the casting technique. A sliding wear test was carried out under applied loads of 10 N, 30 N and 50 N at a fixed sliding speed of 1 m/s using a pin-on-disc configuration. The wear test was conducted in dry conditions at room temperature of ∼25 o C. Detailed analysis of the microstructure, worn surface, collected debris and microhardness was undertaken in order to investigate the differences between the as-cast alloys with different levels of cerium addition. The addition of 1-5 wt% cerium was found to lead to the precipitation of intermetallic phases (Al-Ce), resulting a needle-like structures. Increasing cerium content up to 2 wt% improved both wear resistance and microhardness of as-cast alloys. Addition of more than 2 wt% cerium, however, led to a decrease in microhardness, resulting in lower wear resistance of the alloys. Moderate wear was observed at all loads, with specific wear rates (K') ranging from 6.82 x 10 -5 with 2 wt% Ce at applied load of 50 N to 21.48 x 10 -5 mm 3 /N m without added Ce at an applied load of 10 N. Based on K' ranges, the as-cast alloys exhibited moderate wear regimes, and the mechanism of wear is a combination of abrasion and adhesion. Alloy containing 2 wt% Ce, with the highest hardness and lowest K' value, showed the greatest wear resistance.

  19. High Coke-Resistance Pt/Mg1-xNixO Catalyst for Dry Reforming of Methane.

    Directory of Open Access Journals (Sweden)

    Faris A J Al-Doghachi

    Full Text Available A highly active and stable nano structured Pt/Mg1-xNixO catalysts was developed by a simple co-precipitation method. The obtained Pt/Mg1-xNixO catalyst exhibited cubic structure nanocatalyst with a size of 50-80 nm and realized CH4 and CO2 conversions as high as 98% at 900°C with excellent stability in the dry reforming of methane. The characterization of catalyst was performed using various kinds of analytical techniques including XRD, BET, XRF, TPR-H2, TGA, TEM, FESEM, FT-IR, and XPS analyses. Characterization of spent catalyst further confirms that Pt/Mg1-xNixO catalyst has high coke-resistance for dry reforming. Thus, the catalyst demonstrated in this study, offers a promising catalyst for resolving the dilemma between dispersion and reducibility of supported metal, as well as activity and stability during high temperature reactions.

  20. Density and dry weight of pigweed by various weed control methods ...

    African Journals Online (AJOL)

    This study evaluates effects of various weeds control methods and nitrogen fertilizer resources on density and dry weight of pigweed and the performance of corn forage as factorial in full random block design with 3 repetitions in research farm of Ferdowsi Mashhad University in 2014. The test treatments include weed ...

  1. Research Notes Use of the dry-weight-rank method of botanical ...

    African Journals Online (AJOL)

    When used in combination with the double sampling (or comparative yield) method of yield estimation, the dry-weight-rank method of botanical analysis provides a rapid non-destructive means of estimating botanical composition. The composition is expressed in terms of the contribution of individual species to total herbage ...

  2. [Bioimpedance vector analysis as a tool for the determination and adjustment of dry weight in patients undergoing hemodialysis].

    Science.gov (United States)

    Atilano-Carsi, Ximena; Miguel, José Luis; Martínez Ara, Jorge; Sánchez Villanueva, Rafael; González García, Elena; Selgas Gutiérrez, Rafael

    2015-05-01

    Overhydration in hemodialysis patients is associated with cardiovascular mortality. Adequate removal of liquids and achievement of dry weight is one of the main goals of therapy. So far there are no clinical or laboratory parameters that are reliable, simple and affordable for its determination. The bioelectrical impedance vector analysis (BIVE) is a tool that allows identifying and monitoring hydration status, so the aim of this study was to use BIVE to adjust the intensity of ultrafiltration and achieve dry weight in hemodialysis patients. We studied 26 patients on hemodialysis, which were performed monthly measurements of bioelectrical impedance for four months. Corresponding vectors were plotted to know in an individual way the state of hydration, according to which the dry weight was adjusted when necessary. Dry weight adjustment was performed in 13 patients, 7 of which required increase and 6 decrease of dry weight. The displacement of vectors on the ellipses corresponded to the type of intervention made. Dry weight was reached in 84.6% of patients at the end of the study with a significant decrease in mean arterial blood pressure and an increase in phase angle in the group of decrease of dry weight. Bioelectrical impedance vector analysis is an useful tool for adjusting the dry weight in patients undergoing hemodialysis. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

  3. Neuropsychiatric safety with liraglutide 3.0 mg for weight management

    DEFF Research Database (Denmark)

    O'Neil, Patrick M; Aroda, V R; Astrup, Arne

    2017-01-01

    with liraglutide 3.0 mg were evaluated post hoc. METHODS: Data from the liraglutide weight-management programme were pooled. Across trials, individuals with a body mass index ≥30 kg/m(2) or ≥27 kg/m(2) with weight-related comorbidities were randomized to once-daily subcutaneous liraglutide 3.0 mg (n = 3384......) or placebo (n = 1941), both with a 500 kcal/day deficit diet plus exercise. Adverse events related to neuropsychiatric safety were collected in all trials. Additionally, in the phase 3a trials, validated mental-health questionnaires were prospectively and systematically administered. RESULTS: In the pooled...... analysis of 5325 randomized and exposed individuals, rates of depression (2.1 versus 2.1 events/100 person-years) and anxiety (1.9 versus 1.7 events/100 person-years) through adverse event reporting were similarly low in the liraglutide group and the placebo group. Nine (0.3%) individuals on liraglutide...

  4. The Effect of Body Weight on Heat Strain Indices in Hot and Dry Climatic Conditions

    Directory of Open Access Journals (Sweden)

    Habibi

    2016-03-01

    Full Text Available Background Being overweight is a characteristic that may influence a person’s heat exchange. Objectives The purpose of this study was to assess the effect of body weight on heat strain indices in hot and dry climatic conditions. Materials and Methods This study was completed with a sample of 30 participants with normal weights, as well as 25 participants who were overweight. The participants were physically inactive for a period of 120 minutes in a climatic chamber with hot and dry conditions (22 - 32°C and with 40% relative humidity (RH.The physiological strain index (PSI and heat strain score index (HSSI questionnaires were used. Simultaneous measurements were completed during heat exposure for periods of five minutes. The resting periods acted as the initial measurements for 15 minutes. Results In both groups, oral temperature, heart rate, and thermal perceptual responses increased during heat exposure. The means and standard deviations of heart rate and oral temperature were gathered when participants were in hot and dry climatic conditions and were not physically active. The heart rates and oral temperatures were 79.21 ± 5.93 bpm and 36.70 ± 0.45°C, respectively, for those with normal weights. For overweight individuals, the measurements for heart rate and oral temperature reached 82.21 ± 8.9 bpm and 37.84 ± 0.37°C, respectively. Conclusions The results showed that, compared to participants with normal weights, physiological and thermal perceptual responses were higher in overweight participants. Therefore, overweight individuals should avoid hot/dry weather conditions to decrease the amount of heat strain.

  5. Understanding the performance and mechanism of Mg-containing oxides as support catalysts in the thermal dry reforming of methane.

    Science.gov (United States)

    Khairudin, Nor Fazila; Sukri, Mohd Farid Fahmi; Khavarian, Mehrnoush; Mohamed, Abdul Rahman

    2018-01-01

    Dry reforming of methane (DRM) is one of the more promising methods for syngas (synthetic gas) production and co-utilization of methane and carbon dioxide, which are the main greenhouse gases. Magnesium is commonly applied in a Ni-based catalyst in DRM to improve catalyst performance and inhibit carbon deposition. The aim of this review is to gain better insight into recent developments on the use of Mg as a support or promoter for DRM catalysts. Its high basicity and high thermal stability make Mg suitable for introduction into the highly endothermic reaction of DRM. The introduction of Mg as a support or promoter for Ni-based catalysts allows for good metal dispersion on the catalyst surface, which consequently facilitates high catalytic activity and low catalyst deactivation. The mechanism of DRM and carbon formation and reduction are reviewed. This work further explores how different constraints, such as the synthesis method, metal loading, pretreatment, and operating conditions, influence the dry reforming reactions and product yields. In this review, different strategies for enhancing catalytic activity and the effect of metal dispersion on Mg-containing oxide catalysts are highlighted.

  6. Microstructural evolution during dry wear test in magnesium and Mg-Y alloy

    Energy Technology Data Exchange (ETDEWEB)

    Somekawa, Hidetoshi, E-mail: SOMEKAWA.Hidetoshi@nims.go.jp [Research Center for Strategic Materials, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Maeda, Shunsuke; Hirayama, Tomoko; Matsuoka, Takashi [Department of Mechanical Engineering, Doshisha University, 1-3 Miyakodani, Tatara, Kyotanabe 610-0321 (Japan); Inoue, Tadanobu [Research Center for Strategic Materials, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Mukai, Toshiji [Department of Mechanical Engineering, Kobe University, 1-1 Rokkodai, Kobe, 657-8501 (Japan)

    2013-01-20

    The friction and wear properties of pure magnesium and the Mg-Y alloy were investigated using the pin-on-disk configuration. The friction and wear resistance of the Mg-Y alloy was superior to those of pure magnesium. The wear mechanism was abrasion under all the conditions. The deformed microstructural evolutions near the surface region were observed by transmission electron microscopy and electron backscatter diffraction. The stress and strain states were also evaluated by finite element analysis (FEA). The deformed microstructures of both alloys consisted of the {l_brace}10-12{r_brace} twinning formation and the FEA results showed the occurrence of plastic deformation even at the beginning of the test. The formation of low angle grain boundaries was also confirmed with an increase in the applied load in the Mg-Y alloy. On the other hand, grain refinement due to dynamic recrystallization was observed in pure magnesium as the wear test progressed. The different microstructures resulted from difference in the surface temperature during the wear test, which was estimated to be around 393 K and 363 K for pure magnesium and the Mg-Y alloy, respectively. The high increment temperature in the fine-grained alloys brought about the occurrence of grain boundary sliding, i.e., material softening, which led to a decrease in the friction and wear properties. The present results indicated that one of the methods for enhancing the friction and wear properties is to increase the dynamic recrystallization temperature.

  7. Dry etching of MgCaO gate dielectric and passivation layers on GaN

    International Nuclear Information System (INIS)

    Hlad, M.; Voss, L.; Gila, B.P.; Abernathy, C.R.; Pearton, S.J.; Ren, F.

    2006-01-01

    MgCaO films grown by rf plasma-assisted molecular beam epitaxy and capped with Sc 2 O 3 are promising candidates as surface passivation layers and gate dielectrics on GaN-based high electron mobility transistors (HEMTs) and metal-oxide semiconductor HEMTs (MOS-HEMTs), respectively. Two different plasma chemistries were examined for etching these thin films on GaN. Inductively coupled plasmas of CH 4 /H 2 /Ar produced etch rates only in the range 20-70 A/min, comparable to the Ar sputter rates under the same conditions. Similarly slow MgCaO etch rates (∼100 A/min) were obtained with Cl 2 /Ar discharges under the same conditions, but GaN showed rates almost an order of magnitude higher. The MgCaO removal rates are limited by the low volatilities of the respective etch products. The CH 4 /H 2 /Ar plasma chemistry produced a selectivity of around 2 for etching the MgCaO with respect to GaN

  8. Early Weight Loss with Liraglutide 3.0 mg Predicts 1-Year Weight Loss and is Associated with Improvements in Clinical Markers.

    Science.gov (United States)

    Fujioka, Ken; O'Neil, Patrick M; Davies, Melanie; Greenway, Frank; C W Lau, David; Claudius, Birgitte; Skjøth, Trine Vang; Bjørn Jensen, Christine; P H Wilding, John

    2016-11-01

    To identify an early response criterion for predicting ≥5% weight loss with liraglutide 3.0 mg at week 56 and to compare efficacy outcomes in early responders (ERs) and early nonresponders (ENRs). Using pooled data from the SCALE Obesity and Prediabetes and SCALE Diabetes trials, weight loss of ≥4% at 16 weeks best predicted ≥5% weight loss after 56 weeks. Weight loss and changes in cardiometabolic risk factors and health-related quality of life were evaluated in ERs (≥4% weight loss at week 16) and ENRs (3.0 mg were 77.3%/22.7% (individuals without type 2 diabetes, T2D) and 62.7%/37.3% (those with T2D). Greater mean weight loss was observed in ERs versus ENRs: 10.8% versus 3.0% (without T2D) and 8.5% versus 3.1% (T2D). In both trials, greater proportions of ERs versus ENRs achieved ≥5%, >10%, and >15% weight loss at week 56 with liraglutide 3.0 mg. Greater improvements in cardiometabolic risk factors and health-related quality of life scores were observed in ERs versus ENRs. The early response criterion was clinically useful to identify individuals who would achieve clinically meaningful weight loss at 56 weeks. © 2016 The Authors Obesity published by Wiley Periodicals, Inc. on behalf of The Obesity Society (TOS).

  9. Early Weight Loss with Liraglutide 3.0 mg Predicts 1‐Year Weight Loss and is Associated with Improvements in Clinical Markers

    Science.gov (United States)

    O'Neil, Patrick M.; Davies, Melanie; Greenway, Frank; C.W. Lau, David; Claudius, Birgitte; Skjøth, Trine Vang; Bjørn Jensen, Christine; P.H. Wilding, John

    2016-01-01

    Objective To identify an early response criterion for predicting ≥5% weight loss with liraglutide 3.0 mg at week 56 and to compare efficacy outcomes in early responders (ERs) and early nonresponders (ENRs). Methods Using pooled data from the SCALE Obesity and Prediabetes and SCALE Diabetes trials, weight loss of ≥4% at 16 weeks best predicted ≥5% weight loss after 56 weeks. Weight loss and changes in cardiometabolic risk factors and health‐related quality of life were evaluated in ERs (≥4% weight loss at week 16) and ENRs (3.0 mg were 77.3%/22.7% (individuals without type 2 diabetes, T2D) and 62.7%/37.3% (those with T2D). Greater mean weight loss was observed in ERs versus ENRs: 10.8% versus 3.0% (without T2D) and 8.5% versus 3.1% (T2D). In both trials, greater proportions of ERs versus ENRs achieved ≥5%, >10%, and >15% weight loss at week 56 with liraglutide 3.0 mg. Greater improvements in cardiometabolic risk factors and health‐related quality of life scores were observed in ERs versus ENRs. Conclusions The early response criterion was clinically useful to identify individuals who would achieve clinically meaningful weight loss at 56 weeks. PMID:27804269

  10. Effect of moisture content and dry unit weight on the resilient modulus of subgrade soils predicted by cone penetration test.

    Science.gov (United States)

    2002-06-01

    The objective of this study was to investigate the effect of moisture content and dry unit weight on the resilient characteristics of subgrade soil predicted by the cone penetration test. An experimental program was conducted in which cone penetratio...

  11. Rotary Friction Welding of Weight Heavy Alloy with Wrought AlMg3 Alloy for Subcaliber Ammunition

    Directory of Open Access Journals (Sweden)

    Olgierd Janusz Goroch

    2017-12-01

    Full Text Available The results of studies concerning friction welding of Weight Heavy Alloy (WHA with AlMg3 alloy are presented. The friction welding of density 17,5 Mg/m3 with aluminum alloy showed that it is possible to reach the joints with the strength exceeding the yield strength of wrought AlMg3 alloy. This strength looks to be promising from point of view of condition which have to be fulfilled in case of armor subcaliber ammunition, where WHA rods play the role Kinetic Energy Penetrators and aluminum is used for projectile ballistic cup.

  12. Rotary Friction Welding of Weight Heavy Alloy with Wrought AlMg3 Alloy for Subcaliber Ammunition

    OpenAIRE

    Olgierd Janusz Goroch; Zbigniew Gulbinowicz

    2017-01-01

    The results of studies concerning friction welding of Weight Heavy Alloy (WHA) with AlMg3 alloy are presented. The friction welding of density 17,5 Mg/m3 with aluminum alloy showed that it is possible to reach the joints with the strength exceeding the yield strength of wrought AlMg3 alloy. This strength looks to be promising from point of view of condition which have to be fulfilled in case of armor subcaliber ammunition, where WHA rods play the role Kinetic Energy Penetrators and aluminum i...

  13. The influence of incorporating MgO into Ni-based cermets by plasma spraying on anode microstructural and chemical stability in dry methane

    Science.gov (United States)

    Lay, E.; Metcalfe, C.; Kesler, O.

    2012-11-01

    The Solution Precursor Plasma Spray (SPPS) process was successfully used to deposit cermet coatings that exhibit fine microstructures with high surface area. MgO addition in Ni-YSZ and Ni-SDC cermets results in (Ni,Mg)O solid solution formation, and nickel particles after reduction are finer than in coatings without magnesia. The influence of MgO on the chemical stability of cermets in anodic operating conditions is discussed. It was found that a sufficient amount of magnesia addition (Ni0.9(MgO)0.1) helps to reduce carbon deposition in dry methane.

  14. Effect of Drying Conditions on the Catalytic Performance, Structure, and Reaction Rates over the Fe-Co-Mn/MgO Catalyst for Production of Light Olefins

    Directory of Open Access Journals (Sweden)

    Majid Abdouss

    2018-01-01

    How to Cite: Abdouss, M., Arsalanfar, M., Mirzaei, N., Zamani, Y. (2018. Effect of Drying Conditions on the Catalytic Performance, Structure, and Reaction Rates over the Fe-Co-Mn/MgO Catalyst for Production of Light Olefins. Bulletin of Chemical Reaction Engineering & Catalysis, 13 (1: 97-112 (doi:10.9767/bcrec.13.1.1222.97-112

  15. Reliability of blood pressure parameters for dry weight estimation in hemodialysis patients.

    Science.gov (United States)

    Susantitaphong, Paweena; Laowaloet, Suthanit; Tiranathanagul, Khajohn; Chulakadabba, Adhisabandh; Katavetin, Pisut; Praditpornsilpa, Kearkiat; Tungsanga, Kriang; Eiam-Ong, Somchai

    2013-02-01

    Chronic volume overload resulting from interdialytic weight gain and inadequate fluid removal plays a significant role in poorly controlled high blood pressure. Although bioimpedance has been introduced as an accurate method for assessing hydration status, the instrument is not available in general hemodialysis (HEMO) centers. This study was conducted to explore the correlation between hydration status measured by bioimpedance and blood pressure parameters in chronic HEMO patients. Multifrequency bioimpedance analysis was used to determine pre- and post-dialysis hydration status in 32 stable HEMO patients. Extracellular water/total body water (ECW/TBW) determined by sum of segments from bioimpedance analysis was used as an index of hydration status. The mean age was 57.9 ± 16.4 years. The mean dry weight and body mass index were 57.7 ± 14.5 kg and 22.3 ± 4.7 kg/m(2), respectively. Pre-dialysis ECW/TBW was significantly correlated with only pulse pressure (r = 0.5, P = 0.003) whereas post-dialysis ECW/TBW had significant correlations with pulse pressure, systolic blood pressure, and diastolic blood pressure (r = 0.6, P = 0.001, r = 0.4, P = 0.04, r = -0.4, and P = 0.02, respectively). After dialysis, the mean values of ECW/TBW, systolic blood pressure, mean arterial pressure, and pulse pressure were significantly decreased. ECW/TBW was used to classify the patients into normohydration (≤ 0.4) and overhydration (>0.4) groups. Systolic blood pressure, mean arterial pressure, and pulse pressure significantly reduced after dialysis in the normohydration group but did not significantly change in the overhydration group. Pre-dialysis pulse pressure, post-dialysis pulse pressure, and post-dialysis systolic blood pressure in the overhydration group were significantly higher than normohydration group. Due to the simplicity and cost, blood pressure parameters, especially pulse pressure, might be a simple reference for clinicians to determine hydration status in HEMO

  16. Leaf area development, dry weight accumulation and solar energy conversion efficiencies of Phaseolus vulgaris L. under different soil moisture levels near Nairobi, Kenya

    NARCIS (Netherlands)

    Muniafu, M.M.; Macharia, J.N.M.; Stigter, C.J.; Coulson, G.L.

    1999-01-01

    Leaf area development, dry weight accumulation and solar energy conversion efficiencies of Phaseolus vulgaris L. cv GLP-2 under two soil moisture levels in two contrasting seasons near Nairobi, Kenya were investigated. The experiment confirms that dry weights and yields of Phaseolus vulgaris are

  17. Improvements in health-related quality of life with liraglutide 3.0 mg compared with placebo in weight management.

    Science.gov (United States)

    Kolotkin, R L; Fujioka, K; Wolden, M L; Brett, J H; Bjorner, J B

    2016-08-01

    Obesity has a negative impact on health-related quality of life (HRQoL). The SCALE Obesity and Prediabetes study investigated the effect of liraglutide 3.0 mg, as adjunct to diet and exercise, on HRQoL in patients with obesity [body mass index (BMI) ≥ 30 kg m(-2) ] or overweight (BMI ≥ 27 kg m(-2) ) with comorbidity. Participants were advised on a 500 kcal d(-1) deficit diet and a 150-min week(-1) exercise programme and were randomised 2:1 to once-daily subcutaneous liraglutide 3.0 mg or placebo. HRQoL was assessed using the Impact of Weight on Quality of Life-Lite (IWQOL-Lite) and Short-Form 36 (SF-36) v2 health questionnaires. Individuals on liraglutide 3.0 mg (n = 2046) had significantly greater improvements in IWQOL-Lite total score (10.6 ± 13.3) vs. placebo (n = 1020) (7.7 ± 12.8) and SF-36 physical (PCS) and mental (MCS) component summary scores (PCS, 3.6 ± 6.8; MCS, 0.2 ± 8.1) vs. placebo (PCS, 2.2 ± 7.7; MCS, -0.9 ± 9.1). The estimated treatment differences were IWQOL-Lite total score 3.1 (95% CI: 2.2; 4.0), P 3.0 mg vs. placebo. More patients on liraglutide 3.0 mg experienced meaningful improvement on the IWQOL-Lite total (P < 0.0001) and the SF-36 PCS (P < 0.0001) scores. © 2016 The Authors. Clinical Obesity published by John Wiley & Sons Ltd on behalf of International Association for the Study of Obesity (IASO).

  18. Effect of magnesium content on the microstructure and dry sliding wear behavior of centrifugally cast functionally graded A356-Mg2Si in situ composites

    Science.gov (United States)

    Ram, Subhash Chandra; Chattopadhyay, K.; Chakrabarty, I.

    2018-04-01

    Functionally graded A356 alloy (Al–7.2Si–0.3Mg) –Mg2Si in situ composites have been synthesized via centrifugal casting route. Mg2Si particles tend to migrate towards the core of the tubular product by centrifugal force. The in situ formed Mg2Si particles in composites are characterized by x-ray diffraction (XRD) analysis, Energy dispersive spectrometry (EDS), Optical, Scanning Electron and Transmission Electron Microscopy. Apart from primary blocky Mg2Si particles the matrix contains other phases viz. Al-Si eutectic, pseudo-binary Al-Mg2Si eutectic and Al-Fe-Si intermetallics. Density is found to decrease and %porosity is increased with increase in volume fraction of Mg2Si. Maximum hardness was observed at the inner core region due to maximum segregation of Mg2Si particles and gradually decreases towards the outer periphery region. The dry sliding wear was evaluated with varying parameters such as normal loads (N) and sliding distances (m). A substantial increase in wear resistance at the inner core region is observed. From the worn surface characterization, the wear mechanisms have been explained.

  19. Dry Sliding Wear Behavior of A356 Alloy/Mg2Sip Functionally Graded in-situ Composites: Effect of Processing Conditions

    Directory of Open Access Journals (Sweden)

    S.C. Ram

    2016-09-01

    Full Text Available In present study, the effect of dry sliding wear conditions of A356 alloy/Mg2Sip functionally graded in-situ composites developed by centrifugal casting method has been studied. A pure commercial A356 alloy (Al–7.5Si–0.3Mg was selected to be the matrix of the composites and primary Mg2Sip reinforcing particles were formed by in-situ chemical reaction with an average grain size of 40-47.8 µm. The Al–(Mg2Sip functionally graded metal matrix composites (FGMMC’s were synthesized by centrifugal casting technique with radial geometry, using two different mould rotating speeds ( 1200 and 1600 rpm. The X-ray diffraction (XRD characterization technique was carried out to confirm the in-situ formed Mg2Si particles in composites. Optical microscopy examination was carried out to reveals the grain refinement of Al-rich grains due to in-situ formed Mg2Si particles. Scanning electron microscope (SEM and Energy dispersive X-ray spectroscopy (EDS techniques were carried out to reveal the distribution of phases, morphological characteristics and confirmation of primary Mg2Si particles in the matrix. The sliding wear behavior was studied using a Pin-on-Disc set-up machine with sliding wear parameters: effect of loads (N, effect of sliding distances (m and effect of Mg on wear at room temperature with a high-carbon chromium steel disc (HRC-64 as counter surfaces. A good correlation was evidenced between the dry sliding behaviour of functionally graded in-situ composites and the distribution of Mg2Si reinforcing particles. Beside the above processing conditions, the dominant wear mechanisms of functionally graded in-situ composites have been correlated with the microstructures. The hardness and wear resistance properties of these composites increase with increasing volume percent of reinforced primary Si/Mg2Si particles toward inner zone of cast cylindrical shapes. The objective of this works was to study the tribological characteristics under dry sliding

  20. Improvements in health-related quality of life with liraglutide 3.0 mg compared with placebo in weight management

    DEFF Research Database (Denmark)

    Kolotkin, R. L.; Fujioka, K.; Wolden, M. L.

    2016-01-01

    Obesity has a negative impact on health-related quality of life (HRQoL). The SCALE Obesity and Prediabetes study investigated the effect of liraglutide 3.0 mg, as adjunct to diet and exercise, on HRQoL in patients with obesity [body mass index (BMI) ≥ 30 kg m−2] or overweight (BMI ≥ 27 kg m−2......) with comorbidity. Participants were advised on a 500 kcal d−1 deficit diet and a 150-min week−1 exercise programme and were randomised 2:1 to once-daily subcutaneous liraglutide 3.0 mg or placebo. HRQoL was assessed using the Impact of Weight on Quality of Life-Lite (IWQOL-Lite) and Short-Form 36 (SF-36) v2 health...... questionnaires. Individuals on liraglutide 3.0 mg (n = 2046) had significantly greater improvements in IWQOL-Lite total score (10.6 ± 13.3) vs. placebo (n = 1020) (7.7 ± 12.8) and SF-36 physical (PCS) and mental (MCS) component summary scores (PCS, 3.6 ± 6.8; MCS, 0.2 ± 8.1) vs. placebo (PCS, 2.2 ± 7.7; MCS, −0...

  1. Identification of impeding factors for dry weight achievement in end-stage renal disease after appropriate kidney graft function.

    Science.gov (United States)

    Rivera-González, Sonia Catalina; Pérez-Grovas, Héctor; Madero, Magdalena; Mora-Bravo, Franklin; Saavedra, Nadia; López-Rodriguez, Javier; Lerma, Claudia

    2014-02-01

    The aim of this study was to evaluate the factors that prevent dry weight achievement in patients with end-stage renal disease (ESRD) in renal replacement therapy through the change in their body weight after kidney transplant (KT) compared with 1 week before KT. The study included 188 ESRD patients of diverse etiology who received living kidney transplantation with normal immediate graft function, 62.2% were male, age 29 ± 11 years old. All patients were on renal replacement therapy for at least 1 month before KT with either hemodiafiltration (N = 106), hemodialysis (N = 25), or peritoneal dialysis (N = 57). Based on body weight difference (after transplant-before transplant), patients with body weight difference ≤2 kg were considered as being close to their dry weight (Group 1, N = 112), whereas patients with body weight difference >2 kg were considered as being overhydrated (Group 2, N = 76). Clinical and biochemical characteristics were obtained from the medical records at three periods of time: time of ESRD initiation (baseline), 1 week before undergoing KT, and 1 week after KT. The mean time (± standard deviation) from renal replacement therapy initiation to the week before KT was 9.2 ± 5 months. Group 2 had a higher proportion of men, antihypertensive use, peritoneal dialysis, and higher urine output during all periods. Before KT, Group 2 had higher systolic and diastolic blood pressures than Group 1. After KT, both systolic and diastolic blood pressures decreased in Group 2, whereas no change occurred in Group 1. Before KT, Group 2 had higher levels of blood urea nitrogen, creatinine, uric acid, and phosphorous compared with Group 1. Compared with baseline, Group 1 had more optimal blood urea nitrogen, creatinine, and uric acid parameters before KT than Group 2. After KT, all parameters improved with respect to baseline in both groups. Hemoglobin, albumin, and sodium were similar between groups, except for higher

  2. VOLUME ESTIMATION, DRY WEIGHT, OIL CONTENT AND QUANTITY OF FENCEPOSTS OF CANDEIA (Eremanthus erythropappus (DC MacLeish

    Directory of Open Access Journals (Sweden)

    José Roberto Soares Scolforo

    2004-06-01

    Full Text Available This research aimed at studying the behavior of volume, dry weight, oil content and fence post quantity per diametric class of candeia; to define its stack factor, with and without diametric class control; and to determine equations for estimating the main stem and branches volume, dry weight and oil content of the hole tree, trunk, branches and leaves and fencepost quantity. Data were obtained from a forest inventory carried out in a native candeia forest located in Aiuruoca county, Minas Gerais state - Brazil. Tree volume was calculated through the Huber formula and oil extraction methods employed were “the solvent method” and “vapor hauling method”. For estimation volume, dry weight, oil content and fencepost number the traditional double entry models were used. The oil weight in 1 cubic meter of wood of small dimensions, trees between 5 and 10cm, is around 6 kilos, while the oil content of the largest trees, between 40 and 45cm, is around 11 kilos. The same tendency is observed for the wood volume, without bark, and in the volume of piled up wood, although in these last situations the magnitude of quantities are different. The oil content of candeia trees present the following behavior: in the stem and branches up to 3cm of diameter with bark, it varies from 1,02% to 1,37%, respectively to plants with diameter between 5 and 10cm and between 40 and 45cm; in the branches with less than 3cm of diameter with bark, it varies from 0,33% to 0,65%,respectively, to plants between 5 and 10cm and between 40 and 45cm of diameter; in the leaves it varies from 0,28% to 0,77%, respectively, for plants between 5-10cm and between 40-45cm of diameter. The average stack factor is 1.9087 and diminishes as diameter classes increases. The best model for estimating oil content, dry weight, fence post quantity and volume is the logarithmic form of Schumacher-Hall model.

  3. Three-site mechanism and molecular weight: Time dependency in liquid propylene batch polymerization using a MgCl2-supported Ziegler-Natta catalyst

    NARCIS (Netherlands)

    Shimizu, Fumihiko; Pater, J.T.M.; Weickert, G.

    2001-01-01

    This article demonstrates that the molecular weight of propylene homopolymer decreases with time, and that the molecular weight distribution (MWD) narrows when a highly active MgCl2-supported catalyst is used in a liquid pool polymerization at constant H2 concentration and temperature. To track the

  4. Mathematical modeling of ethanol production in solid-state fermentation based on solid medium' dry weight variation.

    Science.gov (United States)

    Mazaheri, Davood; Shojaosadati, Seyed Abbas; Zamir, Seyed Morteza; Mousavi, Seyyed Mohammad

    2018-04-21

    In this work, mathematical modeling of ethanol production in solid-state fermentation (SSF) has been done based on the variation in the dry weight of solid medium. This method was previously used for mathematical modeling of enzyme production; however, the model should be modified to predict the production of a volatile compound like ethanol. The experimental results of bioethanol production from the mixture of carob pods and wheat bran by Zymomonas mobilis in SSF were used for the model validation. Exponential and logistic kinetic models were used for modeling the growth of microorganism. In both cases, the model predictions matched well with the experimental results during the exponential growth phase, indicating the good ability of solid medium weight variation method for modeling a volatile product formation in solid-state fermentation. In addition, using logistic model, better predictions were obtained.

  5. Rational design of Mg-Al mixed oxide-supported bimetallic catalysts for dry reforming of methane

    Energy Technology Data Exchange (ETDEWEB)

    Tsyganok, Andrey I. [Centre for Catalysis Research and Innovation, Department of Chemistry, University of Ottawa, D' Iorio Hall, 10 Marie Curie Street, Ottawa, Ont. (Canada); Inaba, Mieko [Natural Gas Technology Development Team, Teikoku Oil Co., 9-23-30 Kitakarasuyama, Setagaya-ku, Tokyo 157-0061 (Japan); Tsunoda, Tatsuo; Uchida, Kunio; Suzuki, Kunio; Hayakawa, Takashi [Institute for Materials and Chemical Process, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba Central 5, 1-1-1 Higashi, Tsukuba 305-8565 (Japan); Takehira, Katsuomi [Department of Applied Chemistry, Faculty of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima 739-8527 (Japan)

    2005-09-18

    A novel synthetic strategy for preparing bimetallic Ru-M (M=Cr, Fe, Co, Ni and Cu) catalysts, supported on Mg-Al mixed oxide, has been introduced. It was based on a 'memory effect', i.e. on the ability of Mg-Al mixed oxide to reconstruct a layered structure upon rehydration with an aqueous solution. By repeated calcinations-rehydration cycles, layered double hydroxide (LDH) precursors of catalysts containing two different metals were synthesized. Bimetallic catalysts were then generated (1) in situ from LDH under methane reforming reaction conditions and (2) from mixed metal oxides obtained by preliminary LDH calcination. Among all the LDH-derived catalysts, a Ru{sup 0.1%}-Ni{sup 5.0%}/MgAlO{sub x} sample revealed the highest activity and selectivity to syngas, a suitable durability and a low coking capacity. A promoting effect of ruthenium on catalytic function of supported nickel was demonstrated. Preliminary LDH calcination was shown to markedly affect the catalytic activity of the derived catalysts and especially their coking properties.

  6. Gas exchange, dry weights, and chlorophyll contents of Populus tremuloides seedlings grown from gamma-irradiated seeds

    International Nuclear Information System (INIS)

    Salmonson, B.J.; Zavitkovski, J.

    1977-01-01

    Photosynthesis and respiration rates of Populus tremuloides seedlings grown from seeds acutely irradiated with gamma rays (at levels of 0, 0.47, 0.94, 1.8, 3.7, 7.5, and 15 kr) were measured using a closed system and infrared (IR) gas analyzer. Dry weights of seedling roots and shoots and chlorophyll contents were also determined. In general, gamma irradiation of seed had little effect on subsequent gas-exchange processes in the plant. Net photosynthesis and dark respiration rates of the seedling at any radiation level were not significantly different from those of the control group. Pooled net photosynthesis of all irradiated seedlings was nonsignificantly lower than that of the control seedlings. The data suggested a slight stimulation in dry-matter production of shoots by low levels of gamma radiation. At the highest levels of radiation, shoot dry weight was significantly reduced. Root production displayed a pattern similar to that of shoots. No trends different from controls were evident in the shoot/root ratios. Total chlorophyll concentrations of the seedling increased over the controls by radiation treatment. Age and radiation effects were evident in the chlorophyll a/b ratios. The chlorophyll a/b ratios decreased with age in both the control and treatment groups. Although in seedlings 39 through 46 days old chlorophyll a/b ratios were higher in the control, chlorophyll a/b ratios were significantly higher in the treatment seedlings at 68 days. Changes in chlorophyll a were primarily responsible for this change

  7. Olive paste oil content on a dry weight basis (OPDW): an indicator for optimal harvesting time in modern olive orchards

    Energy Technology Data Exchange (ETDEWEB)

    Zipori, I.; Bustan, A.; Kerem, Z.; Dag, A.

    2016-07-01

    In modern oil olive orchards, mechanical harvesting technologies have significantly accelerated harvesting outputs, thereby allowing for careful planning of harvest timing. While optimizing harvest time may have profound effects on oil yield and quality, the necessary tools to precisely determine the best date are rather scarce. For instance, the commonly used indicator, the fruit ripening index, does not necessarily correlate with oil accumulation. Oil content per fruit fresh weight is strongly affected by fruit water content, making the ripening index an unreliable indicator. However, oil in the paste, calculated on a dry weight basis (OPDW), provides a reliable indication of oil accumulation in the fruit. In most cultivars tested here, OPDW never exceeded ca. 0.5 g·g–1 dry weight, making this threshold the best indicator for the completion of oil accumulation and its consequent reduction in quality thereafter. The rates of OPDW and changes in quality parameters strongly depend on local conditions, such as climate, tree water status and fruit load. We therefore propose a fast and easy method to determine and monitor the OPDW in a given orchard. The proposed method is a useful tool for the determination of optimal harvest timing, particularly in large plots under intensive cultivation practices, with the aim of increasing orchard revenues. The results of this research can be directly applied in olive orchards, especially in large-scale operations. By following the proposed method, individual plots can be harvested according to sharp thresholds of oil accumulation status and pre-determined oil quality parameters, thus effectively exploiting the potentials of oil yield and quality. The method can become a powerful tool for scheduling the harvest throughout the season, and at the same time forecasting the flow of olives to the olive mill. (Author)

  8. Impact of non-binder ingredients and molecular weight of polymer binders on heat assisted twin screw dry granulation.

    Science.gov (United States)

    Liu, Y; Thompson, M R; O'Donnell, K P

    2018-01-30

    Two grades of commercial AFFINISOL™ HPMC HME were used as polymer binders to explore the influence of polymer viscosity and concentration on a novel heat assisted dry granulation process with a twin screw extruder. Contributions of other non-binder ingredients in the formulations were also studied for lactose, microcrystalline cellulose and an active pharmaceutical ingredient of caffeine. As sensitive indicators of processing conditions that expose the drug to high internally generated heat, dehydration of α-lactose monohydrate and polymorphic transformation of caffeine were monitored by differential scanning calorimetry (DSC) and powder X-ray diffraction (XRD). Additionally, any decomposition of caffeine was determined by high-performance liquid chromatography (HPLC). Granular samples were characterized by particle size, circularity, fracture strength and their temperature on the exit of extruder. Higher screw speed and lower feed rate were found to help particles agglomerate by allowing feed particles a greater opportunity to increase in temperature. Lower binder molecular weight and higher binder concentration enable granules to build stronger strength and thereby lead to higher particle size. This new twin screw dry granulation was demonstrated as offering advantages over conventional hot melt granulation by minimizing thermal degradation of the tested ingredients. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Dry weight assessment by combined ultrasound and bioimpedance monitoring in low cardiovascular risk hemodialysis patients: a randomized controlled trial.

    Science.gov (United States)

    Siriopol, Dimitrie; Onofriescu, Mihai; Voroneanu, Luminita; Apetrii, Mugurel; Nistor, Ionut; Hogas, Simona; Kanbay, Mehmet; Sascau, Radu; Scripcariu, Dragos; Covic, Adrian

    2017-01-01

    Fluid overload is associated with adverse outcomes in hemodialysis (HD) patients. The precise assessment of hydration status in HD patients remains a major challenge for nephrologists. Our study aimed to explore whether combining two bedside methods, lung ultrasonography (LUS) and bioimpedance, may provide complementary information to guide treatment in specific HD patients. In total, 250 HD patients from two dialysis units were included in this randomized clinical trial. Patients were randomized 1:1 to have a dry weight assessment based on clinical (control) or LUS with bioimpedance in case of clinical hypovolemia (active)-guided protocol. The primary outcome was to assess the difference between the two groups on a composite of all-cause mortality and first cardiovascular event (CVE)-including death, stroke, and myocardial infarction. During a mean follow-up period was 21.3 ± 5.6 months, there were 54 (21.6%) composite events in the entire population. There was a nonsignificant 9% increase in the risk of this outcome in the active arm (HR = 1.09, 95% CI 0.64-1.86, p = 0.75). Similarly, there were no differences between the two groups when analyzing separately the all-cause mortality and CVE outcomes. However, patients in the active arm had a 19% lower relative risk of pre-dialytic dyspnea (rate ratio-0.81, 95% CI 0.68-0.96), but a 26% higher relative risk of intradialytic cramps (rate ratio-1.26, 95% CI 1.16-1.37). This study shows that a LUS-bioimpedance-guided dry weight adjustment protocol, as compared to clinical evaluation, does not reduce all-cause mortality and/or CVE in HD patients. A fluid management protocol based on bioimpedance with LUS on indication might be a better strategy.

  10. Dry Season Effect on Live Weight and some Body Dimensions of Working Donkeys in the Sudano-sahel Region of Cameroon

    Directory of Open Access Journals (Sweden)

    Ebangi, AL.

    2005-01-01

    Full Text Available Live weight (LW, heart girth (HG, trunk length (TL, body length (BL and height-at-withers (HW of 135 working donkeys, aged between two and 15 years, were monitored during the dry season of 1996 and 1997. This was to determine period(s of the dry season when feed supplementation and/or health care should be reinforced in preparation of high work demands during the rainy season. Variations in LW, HG, TL, BL, HW, HG:HW and TL:HW from start of the dry season to the start of the rainy season were highly significant (P< 0.001. Correlations between live weight and the other measures were positive and highly significant (P< 0.0001. Males showed weight gains between start of the cold-dry-season (CDS and start of the hot-dryseason (HDS. Weight gains in castrates were between start of the CDS and end of the HDS (April. Female donkeys maintained weight gains through out the dry season. Consequently, supplementation of castrates and males at the beginning (January and end (April of the HDS as to reinforce and maintain significant weight gains for maximize draught energy potential for rainy season work demands, is necessary. Where the female donkey express weight gain but poor bodied there will be need for supplementation in order to booster and enhance endurance. Also, estimates of HG, TL, BL, HW, HG:HW and TL:HW may be useful indicators for the selection of working donkeys as to optimize draft capacity and endurance for rainy season work demands.

  11. The comparative evaluation of patients′ body dry weight under hemodialysis using two methods: Bioelectrical impedance analysis and conventional method

    Directory of Open Access Journals (Sweden)

    Neda Alijanian

    2012-01-01

    Full Text Available Background: Dry weight (DW is an important concept related to patients undergoing hemodialysis. Conventional method seems to be time consuming and operator dependent. Bio impedance analysis (BIA is a new and simple method reported to be an accurate way for estimating DW. In this study, we aimed to compare the conventional estimation of DW with measuring DW by BIA. Materials and Methods: This study involved 130 uremic patients, performed in Isfahan, Iran. DW was calculated by both conventional (CDW and BIA (BIADW method and results were compared based on different grouping factors including sex, underlying cause of renal failure (RF (diabetic RF and non-diabetic RF, body mass index (BMI status, and sessions of hemodialysis. We also calculated the difference between DWs of 2 methods (DW diff = CDW-BIADW. Results: The mean of BIADW was significantly lower than CDW (57.20 ± 1.82 vs 59.36 ± 1.77, P value < 0.001. After grouping cases according to the underlying cause, BMI, sex, and dialysis sessions BIADW was significantly lower than CDW. Conclusion: Based on the combination of problems with CDW measurement which are corrected by BIA, and more clinical reliability of CDW, we concluded that although conventional method is a time-consuming and operator-dependent way to assess DW, DW could be estimated by combining both of these methods by finding the mathematic correlation between these methods.

  12. Effect of Cover Crops and Nitrogen Fertilizer on Total Production of Forage Corn and Dry Weight of Weeds

    Directory of Open Access Journals (Sweden)

    R Fakhari

    2014-10-01

    Full Text Available To evaluate the effect of cover crops, split application of nitrogen and control weeds on forage corn and weed biomass a factorial experiment based on randomized complete block design with three replications and three factors was conducted at the Agricultural Research Station of Ardabil (Iran during 2012 crop year. The first factor was cover crops (consisting of winter rye, hairy vetch, berseem clover, with and without weeding as controls. The second factor was two levels of split application of 225 kg.ha-1 urea at two growth stages forage corn: the first level (N1= 1/2 at planting and 1/2 at 8-10 leaf stage, second level (N2= 1/3 at planting, 1/3 at 8-10 leaf and 1/3 one week before tasselling stage. The third factor consisted of two levels of weed control: weeding at 8 leaves and weeding one week before tasselling. Results showed that winter rye, hairy vetch and berseem clover cover crops decreased total weed dry weights up to 87, 82 and 65 % respectively as compared to control (without weeding. Cover crops and nitrogen application time had a significant effect on yield of fresh forage corn and cover crops. Based on the advantages of effective weed control and higher forage production of hairy vetch it can be recommended as proper cover crop.

  13. Structure characterization of the central repetitive domain of high molecular weight gluten proteins .2. Characterization in solution and in the dry state

    NARCIS (Netherlands)

    van Dijk, A.A.; De Boef, E.; Bekkers, A.; van Wijk, L.L.; van Swieten, E.; Hamer, R.J.; Robillard, G.T.

    The structure of the central repetitive domain of high molecular weight (HMW) wheat gluten proteins was characterized in solution and in the dry state using HMW proteins Bx6 and Bx7 and a subcloned, bacterially expressed part of the repetitive domain of HMW Dx5. Model studies of the HMW consensus

  14. Genetic covariance functioners for live weight, condition score, and dry-matter intake measured at different lactations stages of Holstein-Friesian heifers

    NARCIS (Netherlands)

    Koenen, E.P.C.; Veerkamp, R.F.

    1998-01-01

    Genetic parameters for live weight, body condition score and dry-matter intake of dairy heifers were estimated using covariance function methodology. Data were from 469 heifers of the Langhill Dairy Cattle Research Centre and included observations during the first 25 weeks in lactation. Genetic

  15. Grain Yield, Dry Weight and Phosphorus Accumulation and Translocation in Two Rice (Oryza sativa L. Varieties as Affected by Salt-Alkali and Phosphorus

    Directory of Open Access Journals (Sweden)

    Zhijie Tian

    2017-08-01

    Full Text Available Salt-alkali is the main threat to global crop production. The functioning of phosphorus (P in alleviating damage to crops from saline-alkaline stress may be dependent on the variety of crop but there is little published research on the topic. This pot experiment was conducted to study if P has any effect on rice (Oryza sativa L. yield, dry matter and P accumulation and translocation in salt-alkaline soils. Plant dry weight and P content at heading and harvest stages of two contrasting saline-alkaline tolerant (Dongdao-4 and sensitive (Tongyu-315 rice varieties were examined under two saline-alkaline (light versus severe soils and five P supplements (P0, P50, P100, P150 and P200 kg ha−1. The results were: in light saline-alkaline soil, the optimal P levels were found for P150 for Dongdao-4 and for P100 for Tongyu-315 with the greatest grain dry weight and P content. Two rice varieties obtained relatively higher dry weight and P accumulation and translocation in P0. In severe saline-alkaline soil, however, dry weight and P accumulation and translocation, 1000-grain weight, seed-setting rate and grain yield significantly decreased, but effectively increased with P application for Dongdao-4. Tongyu-315 showed lower sensitivity to P nutrition. Thus, a more tolerant variety could have a stronger capacity to absorb and translocate P for grain filling, especially in severe salt-alkaline soils. This should be helpful for consideration in rice breeding and deciding a reasonable P application in saline-alkaline soil.

  16. Effect of curing methods, packaging and gamma irradiation on the weight loss and dry matter percent of garlic during curing and storage

    International Nuclear Information System (INIS)

    Mahmoud, A.A.; El-Oksh, I.I.; Farag, S.E.A.

    1988-01-01

    The Egyptian garlic plants, showed higher percent of weight loss at 17 or 27 days from curing compared to those of Chinese plants. The curing period of 17 days seemed satisfactory for the Egyptian cultivar, whereas, 27 days seemed to be enough for the Chinese garlic. No significant differences were observed between common and shaded curing methods in weight loss per cent. The Chinese garlic contained higher dry matter percentage than those of the Egyptian cultivar. Shaded cured plants of the two cultivars contained higher dry matter percent than those subjected to the common curing methods. Irradiation of garlic bulbs, shaded curing method and sack packaging decreased, in general the weight loss during storage in comparison with other treatments

  17. Efficacy and safety of liraglutide 3.0 mg for weight management are similar across races: subgroup analysis across the SCALE and phase II randomized trials.

    Science.gov (United States)

    Ard, J; Cannon, A; Lewis, C E; Lofton, H; Vang Skjøth, T; Stevenin, B; Pi-Sunyer, X

    2016-04-01

    The efficacy and safety of liraglutide 3.0 mg versus placebo, as adjunct to diet and exercise, was evaluated in racial subgroups. This post hoc analysis of pooled data from five double-blind randomized, placebo-controlled trials was conducted in 5325 adults with either a body mass index (BMI) ≥27 kg/m(2) plus ≥1 comorbidity or a BMI ≥30 kg/m(2). Statistical interaction tests evaluated possible treatment effect differences between racial subgroups: white (4496, 84.4%), black/African-American (550, 10.3%), Asian (168, 3.2%) and other (111, 2.1%). Effects of liraglutide 3.0 mg on weight loss, associated metabolic effects and safety profile were generally consistent across racial subgroups. All achieved statistically significant mean weight loss at end-of-treatment with liraglutide 3.0 mg versus placebo: white 7.7% versus 2.3%, black/African-American 6.3% versus 1.4%, Asian 6.3% versus 2.5%, other 7.3% versus 0.49%. Treatment effects on weight and cardiovascular risk markers generally showed no dependence on race (interaction test p > 0.05). Adverse events were similar across racial subgroups. © 2016 John Wiley & Sons Ltd.

  18. Influence of Ca/Mg ratio on phytoextraction properties of Salix viminalis. II. Secretion of low molecular weight organic acids to the rhizosphere.

    Science.gov (United States)

    Magdziak, Z; Kozlowska, M; Kaczmarek, Z; Mleczek, M; Chadzinikolau, T; Drzewiecka, K; Golinski, P

    2011-01-01

    A hydroponic experiment in a phytotron was performed to investigate the effect of two different Ca/Mg ratios (4:1 and 1:10) and trace element ions (Cd, Cu, Pb and Zn) in solution on the efficiency of low molecular weight organic acid (LMWOA) formation in Salix viminalis rhizosphere. Depending on the Ca/Mg ratio and presence of selected trace elements at 0.5mM concentration, the amount and kind of LMWOAs in the rhizosphere were significantly affected. In physiological 4:1 Ca/Mg ratio the following complex of acids was observed: malonic (Pb, Zn), citric, lactic, maleic and succinic (Zn) acids. Under 1:10 Ca/Mg ratio, citric (Cd, Zn), maleic and succinic (Cd, Cu, Pb, Zn) acids were seen. Additionally, high accumulation of zinc and copper in all systems was observed, with the exception of those where one of the metals was at higher concentration. Summing up, the results indicate a significant role of LMWOAs in Salix phytoremediation abilities. Both effects can be modulated depending on the mutual Ca/Mg ratio. Copyright © 2010 Elsevier Inc. All rights reserved.

  19. Specific leaf mass, fresh: dry weight ratio, sugar and protein contents in species of Lamiaceae from different light environments

    Directory of Open Access Journals (Sweden)

    M Castrillo

    2005-06-01

    Full Text Available Samples from eleven species of Lamiaceae were collected from different light environments in Venezuela for laboratory analysis.The studied species were: Plectranthus scutellarioides (Ps, Scutellaria purpurascens (Sp, Hyptis pectinata (Hp, H. sinuata (Hs, Leonorus japonicus (Lj, Plecthranthus amboinicus (Pa Ocimum basilicum (Ocb, O.campechianum (Occ Origanum majorana (Orm, Rosmarinus officinali ,(Ro and Salvia officinalis (So. Protein and soluble sugar contents per unit of area were measured, Specific Leaf Mass (SLMand fresh: dry weight (FW/DW ratios were calculated. The higher values for soluble sugars contents were present in sun species: Lj, Pa, Ocb, Occ, Or. m, Ro and So; the lower values were obtained in low light species: Ps, Sp, Hp, Hs. The values of protein content do not show any clear trend or difference between sun and shade environments. The lowest values for the fresh weight: dry weight ratio are observed in sun species with the exception of Lj and Pa, while the highest value is observed in Pa, a succulent plant. The higher values of specific leaf mass (SLM(Kg DMm-2 are observed in sun plants. The two way ANOVA revealed that there were significant differences among species and between sun and low light environments for sugar content and FW: DW ratio, while SLM was significant for environments but no significant for species, and not significant for protein for both species and environments. The soluble sugar content, FW: DW ratio and SLM values obtained in this work, show a clear separation between sun and shade plants. The sugar content and FW:DW ratio are distinctive within the species,and the light environment affected sugar content, FW:DW ratio and SLM. These species may be shade-tolerant and able to survive in sunny environments. Perhaps these species originated in shaded environments and have been adapting to sunny habitats.Rev.Biol.Trop.53(1-2:23-28.Epub 2005 Jun 24En once especies de la familia Lamiaceae: Plecthranthus

  20. Olive paste oil content on a dry weight basis (OPDW: an indicator for optimal harvesting time in modern olive orchards

    Directory of Open Access Journals (Sweden)

    Zipori, I.

    2016-06-01

    Full Text Available In modern oil olive orchards, mechanical harvesting technologies have significantly accelerated harvesting outputs, thereby allowing for careful planning of harvest timing. While optimizing harvest time may have profound effects on oil yield and quality, the necessary tools to precisely determine the best date are rather scarce. For instance, the commonly used indicator, the fruit ripening index, does not necessarily correlate with oil accumulation. Oil content per fruit fresh weight is strongly affected by fruit water content, making the ripening index an unreliable indicator. However, oil in the paste, calculated on a dry weight basis (OPDW, provides a reliable indication of oil accumulation in the fruit. In most cultivars tested here, OPDW never exceeded ca. 0.5 g.g–1 dry weight, making this threshold the best indicator for the completion of oil accumulation and its consequent reduction in quality thereafter. The rates of OPDW and changes in quality parameters strongly depend on local conditions, such as climate, tree water status and fruit load. We therefore propose a fast and easy method to determine and monitor the OPDW in a given orchard. The proposed method is a useful tool for the determination of optimal harvest timing, particularly in large plots under intensive cultivation practices, with the aim of increasing orchard revenues. The results of this research can be directly applied in olive orchards, especially in large-scale operations. By following the proposed method, individual plots can be harvested according to sharp thresholds of oil accumulation status and pre-determined oil quality parameters, thus effectively exploiting the potentials of oil yield and quality. The method can become a powerful tool for scheduling the harvest throughout the season, and at the same time forecasting the flow of olives to the olive mill.En los modernos olivares, las tecnologías de recogida mecánica han acelerado significativamente la recogida

  1. EFFECTS OF LIRAGLUTIDE 3.0 MG ON WEIGHT AND RISK FACTORS IN HISPANIC VERSUS NON-HIPANIC POPULATIONS: SUBGROUP ANALYSIS FROM SCALE RANDOMIZED TRIALS.

    Science.gov (United States)

    O'Neil, Patrick M; Garvey, W Timothy; Gonzalez-Campoy, J Michael; Mora, Pablo; Ortiz, Rafael Violante; Guerrero, German; Claudius, Birgitte; Pi-Sunyer, Xavier

    2016-11-01

    Scarce data exist on pharmacotherapy for obesity in Hispanic individuals. This post hoc analysis of pooled data from 4 phase 3a trials compared the efficacy and safety of liraglutide 3.0 mg versus placebo, as adjunct to a reduced-calorie diet and physical activity, in Hispanic versus non-Hispanic subgroups. We conducted the double-blind randomized, placebo-controlled trials in adults with a minimum body mass index (BMI) of 27 kg/m 2 with at least 1 comorbidity, or a minimum BMI of 30 kg/m 2 , at clinical research sites worldwide. In this analysis, we investigated possible differences in treatment effects between 534 Hispanics (10.4% of the population) and 4,597 non-Hispanics (89.6%) through statistical tests of interaction between subgroups and treatment. Variables examined included mean and categorical weight change, cardiovascular risk markers, and safety data. Both subgroups achieved clinically significant mean weight loss at end-of-treatment with liraglutide 3.0 mg versus placebo: Hispanics 7.0% versus 1.5%, treatment difference -5.1% (95% CI, -6.2 to -4.0); non-Hispanics 7.5% versus 2.3%, -5.2% (95% CI, -5.5 to -4.8). More individuals in both subgroups lost ≥5%, >10%, and >15% of their baseline weight with liraglutide 3.0 mg than with placebo. Efficacy endpoints generally did not vary with ethnicity (P>.05). Adverse events were comparable between ethnic subgroups, with more gastrointestinal disorders reported with liraglutide 3.0 mg than placebo. Efficacy and safety were largely similar between Hispanic and non-Hispanic subgroups. Results support that liraglutide 3.0 mg, used with a reduced-calorie diet and physical activity, can facilitate weight loss in Hispanic individuals. A1c = glycated hemoglobin BMI = body mass index CI = confidence interval FPG = fasting plasma glucose GLP-1 = glucagon-like peptide-1 hsCRP = high-sensitivity C-reactive protein SCALE = Satiety and Clinical Adiposity - Liraglutide Evidence in individuals with and without diabetes T2DM

  2. Successful pregnancy following low-dose hCG administration in addition to hMG in a patient with hypothalamic amenorrhea due to weight loss.

    Science.gov (United States)

    Tsutsumi, Ryo; Fujimoto, Akihisa; Osuga, Yutaka; Harada, Miyuki; Takemura, Yuri; Koizumi, Minako; Yano, Tetsu; Taketani, Yuji

    2012-06-01

    We describe successful ovulation induction with low-dose hCG administration in addition to hMG in a patient with refractory hypothalamic amenorrhea. A 24-year-old woman with weight loss-related amenorrhea underwent ovulation induction and intracytoplasmic sperm injection (ICSI). Administration of exogenous gonadotropins was ineffective in ovulation induction. Supplementation with low-dose hCG in order to increase luteinizing hormone (LH) activity in the late follicular phase produced late folliculogenesis and steroidogenesis, and ovulation was then successfully induced. This report reacknowledges the critical role that LH plays cooperatively with follicle-stimulating hormone in both folliculogenesis and steroidogenesis.

  3. Effect of storage conditions on the weight and appearance of dried blood spot samples on various cellulose-based substrates.

    Science.gov (United States)

    Denniff, Philip; Spooner, Neil

    2010-11-01

    Before shipping and storage, dried blood spot (DBS) samples must be dried in order to protect the integrity of the spots. In this article, we examine the time required to dry blood spot samples and the effects of different environmental conditions on their integrity. Under ambient laboratory conditions, DBS samples on Whatman 903(®), FTA(®) and FTA(®) Elute substrates are dry within 90 min of spotting. An additional 5% of moisture is lost during subsequent storage with desiccant. When exposed to elevated conditions of temperature and relative humidity, the DBS samples absorb moisture. DBS samples on FTA lose this moisture on being returned to ambient conditions. DBS samples on 903 show no visible signs of deterioration when stored at elevated conditions. However, these conditions cause the DBS to diffuse through the FTA Elute substrate. Blood spots are dry within 90 min of spotting. However, the substrates examined behave differently when exposed to conditions of high relative humidity and temperature, in some cases resulting in the integrity of the substrate and DBS sample being compromised. It is recommended that these factors be investigated as part of method development and validation.

  4. Real-time measurement system for tracking birefringence, weight, thickness, and surface temperature during drying of solution cast coatings and films

    Science.gov (United States)

    Unsal, E.; Drum, J.; Yucel, O.; Nugay, I. I.; Yalcin, B.; Cakmak, M.

    2012-02-01

    This paper describes the design and performance of a new instrument to track temporal changes in physical parameters during the drying behavior of solutions, as well as curing of monomers. This real-time instrument follows in-plane and out-of-plane birefringence, weight, thickness, and surface temperature during the course of solidification of coatings and films through solvent evaporation and thermal or photocuring in a controlled atmosphere. It is specifically designed to simulate behavior of polymer solutions inside an industrial size, continuous roll-to-roll solution casting line and other coating operations where resins are subjected to ultraviolet (UV) curing from monomer precursors. Controlled processing parameters include air speed, temperature, initial cast thickness, and solute concentration, while measured parameters are thickness, weight, film temperature, in-plane and out-of-plane birefringence. In this paper, we illustrate the utility of this instrument with solution cast and dried poly (amide-imide)/DMAc (Dimethylacetamide) solution, water based black paint, and organo-modified clay/NMP (N-Methylpyrrolidone) solution. In addition, the physical changes that take place during UV photo polymerization of a monomer are tracked. This instrument is designed to be generic and it can be used for tracking any drying/swelling/solidification systems including paper, foodstuffs such as; grains, milk as well as pharmaceutical thin paste and slurries.

  5. Nickel catalyst supported on magnesium and zinc aluminates (MgAl{sub 2}O{sub 4} and ZnAl{sub 2}O{sub 4}) spinels for dry reforming of methane

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, L.C.B. de; Melo, D.M. de A.; Melo, M.A. de F.; Barros, J.M. de F.; Braga, R.M.; Costa, C. de C.; Rodrigues, G., E-mail: ieda.garcia@pq.cnpq.br [Universidade Federal da Paraiba (LACOM/UFPB), Joao Pessoa, PB (Brazil). Dept. de Quimica

    2017-01-15

    Materials such as MgAl{sub 2}O{sub 4} and ZnAl{sub 2}O{sub 4} assessed in the reaction of dry reforming of methane to produce syngas were synthesized by microwave-assisted combustion method using urea as fuel. Samples of synthesized oxides were calcined at 800 °C for 2 h and impregnated with 5% nickel. The impregnated samples were calcined at 850 °C for 4 h to obtain the desired phases. The results of the catalytic tests showed that the catalysts are active for the reaction of dry reforming of methane, and the catalyst that showed the best performance for methane conversion was 5% Ni/MgAl{sub 2}O{sub 4} calcined at 850 °C/4 h. (author)

  6. Flow Cytometry Pulse Width Data Enables Rapid and Sensitive Estimation of Biomass Dry Weight in the Microalgae Chlamydomonas reinhardtii and Chlorella vulgaris

    Science.gov (United States)

    Chioccioli, Maurizio; Hankamer, Ben; Ross, Ian L.

    2014-01-01

    Dry weight biomass is an important parameter in algaculture. Direct measurement requires weighing milligram quantities of dried biomass, which is problematic for small volume systems containing few cells, such as laboratory studies and high throughput assays in microwell plates. In these cases indirect methods must be used, inducing measurement artefacts which vary in severity with the cell type and conditions employed. Here, we utilise flow cytometry pulse width data for the estimation of cell density and biomass, using Chlorella vulgaris and Chlamydomonas reinhardtii as model algae and compare it to optical density methods. Measurement of cell concentration by flow cytometry was shown to be more sensitive than optical density at 750 nm (OD750) for monitoring culture growth. However, neither cell concentration nor optical density correlates well to biomass when growth conditions vary. Compared to the growth of C. vulgaris in TAP (tris-acetate-phosphate) medium, cells grown in TAP + glucose displayed a slowed cell division rate and a 2-fold increased dry biomass accumulation compared to growth without glucose. This was accompanied by increased cellular volume. Laser scattering characteristics during flow cytometry were used to estimate cell diameters and it was shown that an empirical but nonlinear relationship could be shown between flow cytometric pulse width and dry weight biomass per cell. This relationship could be linearised by the use of hypertonic conditions (1 M NaCl) to dehydrate the cells, as shown by density gradient centrifugation. Flow cytometry for biomass estimation is easy to perform, sensitive and offers more comprehensive information than optical density measurements. In addition, periodic flow cytometry measurements can be used to calibrate OD750 measurements for both convenience and accuracy. This approach is particularly useful for small samples and where cellular characteristics, especially cell size, are expected to vary during growth. PMID

  7. Neuropsychiatric safety with liraglutide 3.0 mg for weight management: Results from randomized controlled phase 2 and 3a trials.

    Science.gov (United States)

    O'Neil, Patrick M; Aroda, Vanita R; Astrup, Arne; Kushner, Robert; Lau, David C W; Wadden, Thomas A; Brett, Jason; Cancino, Ana-Paula; Wilding, John P H

    2017-11-01

    Liraglutide, a GLP-1 receptor agonist, regulates appetite via receptors in the brain. Because of concerns regarding the potential of centrally-acting anti-obesity medications to affect mental health, pooled neuropsychiatric safety data from all phase 2 and 3a randomized, double-blind trials with liraglutide 3.0 mg were evaluated post hoc. Data from the liraglutide weight-management programme were pooled. Across trials, individuals with a body mass index ≥30 or ≥27 kg/m 2 with weight-related comorbidities were randomized to once-daily subcutaneous liraglutide 3.0 mg (n = 3384) or placebo (n = 1941), both with a 500 kcal/d deficit diet, plus exercise. Adverse events related to neuropsychiatric safety were collected in all trials. Additionally, in the phase 3a trials, validated mental-health questionnaires were prospectively and systematically administered. In the pooled analysis of 5325 randomized and exposed individuals, rates of depression (2.1 vs 2.1 events/100 person-years) and anxiety (1.9 vs 1.7 events/100 person-years) through adverse event reporting were similarly low in liraglutide and placebo groups. Nine (0.3%) individuals receiving liraglutide and 2 (0.1%) receiving placebo reported adverse events of suicidal ideation or behaviour. In phase 3a trials, mean baseline Patient Health Questionnaire-9 scores of 2.8 ± 3.0 vs 2.9 ± 3.1 for liraglutide vs placebo improved to 1.8 ± 2.7 vs 1.9 ± 2.7, respectively, at treatment end; 34/3291 individuals (1.0%) receiving liraglutide 3.0 mg vs 19/1843 (1.0%) receiving placebo reported suicidal ideation on the Columbia-Suicide Severity Rating Scale. Results of this exploratory pooled analysis provide no cause for concern regarding the neuropsychiatric safety of treatment with liraglutide 3.0 mg in patients similar to those included in the examined trials. Although there was a small numerical imbalance in suicidal ideation with liraglutide through adverse event reporting, no

  8. Dry weight and N-uptake by rice plants fertilized with azolla and N-15 enriched urea

    International Nuclear Information System (INIS)

    Abdel-Monem, M.; Gadalla, A.M.; Abbady, Kh.

    1994-01-01

    Integrated soil fertility management is essential if soil productivity is to be sustained or improved. In view the recently high cost of N-fertilizers, interest was generated in using Azolla in rice fields. A greenhouse experiment was conducted to study the fate of N-15 labelled urea to rice with or without Azolla application, also to examine the effect of the soil moisture regime at the time of urea application on nitrogen recovery. The results indicated that addition of urea to dry soil gave more than 20% of the rice dry matter as compared to the urea application to wet soil which was also reflected on the N-uptake by the rice. Also N-15 recovery by plant was increased from 22% to 41% when urea was applied to wet and dry soil respectively. At the same time N-losses dropped from 62% to 29%. Addition of Azolla to rice provided rice with 63% of the nitrogen provided by urea, this may be attributed not only to N-fixation by Azolla, but also to its role in reducing the N-losses. Application of Azolla reduced the losses of applied nitrogen from 45.5% to 22.5%. Thus, integration between Azolla and urea is valuable in N-fixation as well as inhibiting nitrogen losses. 2 tabs

  9. Structure characterization of the central repetitive domain of high molecular weight gluten proteins. II. Characterization in solution and in the dry state

    OpenAIRE

    Dijk, Alard A. van; Boef, Esther de; Bekkers, August; Wijk, Lourens L. van; Swieten, Eric van; Hamer, Rob J.; Robillard, George T.

    1997-01-01

    The structure of the central repetitive domain of high molecular weight HMW) wheat gluten proteins was characterized in solution and in the dry state using HMW proteins Bx6 and Bx7 and a subcloned, bacterially expressed part of the repetitive domain of HMW Dx5. Model studies of the HMW consensus peptides PGQGQQ and GYYPTSPQQ formed the basis for the data analysis (van Dijk AA et al., 1997, Protein Sci 6:637-648). In solution, the repetitive domain contained a continuous nonoverlapping series ...

  10. An evaluation of the use of the dry-weight-rank and the comparative yield biomass estimation methods in paramo ecosystem research

    Directory of Open Access Journals (Sweden)

    Hofstede Robert G.M.

    1993-12-01

    Full Text Available The use of the combination of the semi-destructive comparative yield method for overall biomass estimation and the non- destructive dry-weight-rank method for studying botanical composition on a dry weight basis in an undisturbed páramo vegetation in the Los Nevados national park (Colombian Central Cordillera was evaluated. These methods, developed for Australian production grasslands, were adapted for use in the páramo ecosystem. The average above ground biomass in the area was estimated as 2864 g dryweight. m-2 (sd.48, of which the bunchgrass Calamagrostis effusa contributed with ca 70%. When used with some adaptations, the comparative yield method seems suitable for biomass estimations in the páramo ecosystem. The here presented estimation of botanical eomposition with this method gave better results than dry-weight-rank method, which had too many shortcomings for use in the complex páramo grassland ecosystem.Se evaluó la aplicabilidad de una combinación de dos étodos para estimar la biomasa  general y la composición botánica, en una vegetación natural paramuna en el Parque Nacional Natural los Nevados (Cordillera Central de Colombia. El primer método (ecomparative yield determina la biomasa general, destruyendo parcialmente la vegetación de los cuadrantes de muestreo y el segundo (dryweight rank determina la composición botánica con base en el peso seco, sin destruir la vegetación. Estos métodos, inicialmente desarrollados para pajonales forrajeros en Australia, se adaptaron para ser utilizados en el ecosistema paramuno. Como resultado se obtuvo una estimación de la biomasa aérea de 2864 g peso seco m2 (desviación stándard 48 en la cual, la gramínea Calamagrostis effusa contribuyó con el 70%. Puede concluirse que el método de producción comparativa es útil para estimar la biomasa en el ecosistema paramuno, siempre y cuando se utilicen las adaptaciones mencionadas. Por otra parte la estimación de la composición bot

  11. Effect of Hibiscus sabdariffa L. Dried Calyx Ethanol Extract on Fat Absorption-Excretion, and Body Weight Implication in Rats

    Science.gov (United States)

    Carvajal-Zarrabal, O.; Hayward-Jones, P. M.; Orta-Flores, Z.; Nolasco-Hipólito, C.; Barradas-Dermitz, D. M.; Aguilar-Uscanga, M. G.; Pedroza-Hernández, M. F.

    2009-01-01

    The effect of Hibiscus sabdariffa L. (Hs) calyx extract on fat absorption-excretion and body weight in rats, was investigated. Rats were fed with either a basal diet (SDC = Control diet) or the same diet supplemented with Hs extracts at 5%, 10% and 15% (SD5, SD10 and SD15). Only SD5 did not show significant increases in weight, food consumption and efficiency compared to SDC. The opposite occurred in SD15 group which showed a significant decrease for these three parameters. The SD10 responses were similar to SD15, with the exception of food consumption. In both SDC and SD5 groups, no body weight loss was observed; however, only in the latter group was there a significantly greater amount of fatty acids found in feces. A collateral effect emerging from the study is that components of Hs extract at the intermediate and greater concentrations used in this experiment could be considered possible antiobesity agents. PMID:19756159

  12. Effect of Hibiscus sabdariffa L. Dried Calyx Ethanol Extract on Fat Absorption-Excretion, and Body Weight Implication in Rats

    Directory of Open Access Journals (Sweden)

    O. Carvajal-Zarrabal

    2009-01-01

    , and . Only did not show significant increases in weight, food consumption and efficiency compared to . The opposite occurred in group which showed a significant decrease for these three parameters. The responses were similar to , with the exception of food consumption. In both and groups, no body weight loss was observed; however, only in the latter group was there a significantly greater amount of fatty acids found in feces. A collateral effect emerging from the study is that components of Hs extract at the intermediate and greater concentrations used in this experiment could be considered possible antiobesity agents.

  13. Effect of molecular weight and ratio of poly ethylene glycols' derivatives in combination with trehalose on stability of freeze-dried IgG.

    Science.gov (United States)

    Mohammad Zadeh, Amir Hossein; Rouholamini Najafabadi, Abdolhosein; Vatanara, Alireza; Faghihi, Homa; Gilani, Kambiz

    2017-12-01

    The influence of poly ethylene glycol (PEG) at different molecular weights (MWs) and ratios was studied on the stability of freeze-dried immune globulin G (IgG). PEGs (600-4000 Dalton) at concentrations of 0.5 and 5% W/V were applied in the presence of 40 and 60% W/W of trehalose to prepare freeze-dried IgG formulations. Size-exclusion chromatography, infra-red spectroscopy, differential scanning calorimeter, and gel electrophoresis were performed to characterize lyophilized samples. Pure IgG demonstrated the highest aggregation of 5.77 ± 0.10% after process and 12.66 ± 0.50% as well as 44.69 ± 0.50% upon 1 and 2 months of storage at 45 °C, respectively. 5% W/V of PEGs 4000 in combination with 40% W/W trehalose, significantly suppressed aggregation, 0.05 ± 0.01%, with minimum aggregation rate constant of 0.32 (1/month). The integrity of IgG molecules and secondary conformation were properly preserved in all formulations comparing native IgG. It could be concluded that appropriate concentration and MW of PEGs, prominently augmented stabilizing effect of trehalose on freeze-dried antibody through inserting additional supportive mechanisms of actions.

  14. Effect of Drought Stress on Water Use Efficiency and Root Dry Weight of Wheat (Triticum aesativum L. and Rye (Secale cereale L. in Competition Conditions

    Directory of Open Access Journals (Sweden)

    F Golestani Far

    2017-10-01

    Full Text Available Introduction Deficiency of water during the plant growth is one of the main factors which reduce the crops production around the world. Drought stress is one of the most important tensions that may occur around the low rainfall, high temperature and wind blowing environments. Plant response to this stress depends on the stage of plant growth and drought intensity. Weeds are unwanted and harmful plants with disturbance in agricultural practices which make increase the cost of crop production and reduce the crop yields. Rye (Secale cereal L. is one of the most important weeds at wheat fields in Iran (Baghestani and Atri, 2003. Low expectations, allelopathic effects and similarity of life cycle and morphology, caused increasing of rye density in winter wheat fields. Water use efficiency (WUE as an important physiological characteristic indicates the ability of plants to water stress. WUE may be affected by climatic and soil or plant factors. In plant communities, competition is one of most important physiological topics (Evans et al, 2003. At Inter-specific competition, weeds interfere to absorbing of light, water and nutrients through the adjacency with crop and so affect the growth and yield of crops. Weeds often compete with crops for soil water and reduce the accessibility of water. Competition between weeds and crops decrease the soil moisture and cause water stress which might decrease the weeds and crops growth. When the supply of water is limited, water drainage overlap areas in soil profile could be occurred relatively fast at early of in the crop life cycle. Materials and Methods In order to study the effects of drought stress on water use efficiency and root dry weight of wheat (Triticum aesativum L. and rye (Secale cereale L. in competition conditions, a pot experiment was conducted in the greenhouse of Agriculture Faculty , University of Birjand in 2012. The experiment was arranged as factorial based on completely randomized design

  15. Relationship between the ability of oral streptococci to interact with platelet glycoprotein Ibalpha and with the salivary low-molecular-weight mucin, MG2.

    Science.gov (United States)

    Plummer, Christopher; Douglas, Charles William Ian

    2006-12-01

    The oral streptococci Streptococcus sanguinis, Streptococcus gordonii and Streptococcus oralis are common aetiological agents of infective endocarditis, and their ability to adhere to and induce the aggregation of platelets is thought to be a virulence trait. The platelet glycoprotein GPIbalpha has been implicated as the adhesion receptor for S. sanguinis and S. gordonii, but it is not known if this is the case for S. oralis and other species. The aim of this study was to determine the GPIbalpha-interactive capability of a range of oral streptococci and to determine the relationship between this capability and their ability to interact with the salivary constituents that they would encounter in their normal habitat. All platelet-adhesive S. sanguinis strains and most S. gordonii strains adhered in a GPIbalpha-dependent manner, but strains of S. oralis, Streptococcus cristatus, Streptococcus parasanguinis and Streptococcus mitis had no direct affinity for platelets. Those strains that were able to bind GPIbalpha also bound to the low-molecular-weight submandibular salivary mucin, MG2, and this interaction was sialic acid-dependent. The data suggest that S. sanguinis and S. gordonii may be efficient colonizers of platelet vegetations because of their adaptation to recognize sialylated salivary mucins. In contrast, S. oralis does not interact with platelets and so is likely to colonize vegetations through an as yet unidentified mechanism.

  16. Statistical models for prediction of dry weight and nitrogen accumulation based on visible and near-infrared hyper-spectral reflectance of rice canopies

    International Nuclear Information System (INIS)

    Takahashi, W.; Nguyen-Cong, V.; Kawaguchi, S.; Minamiyama, M.; Ninomiya, S.

    2000-01-01

    Various multivariate regression models were examined with ten-fold cross-validation to develop efficient, accurate models to predict dry weight and nitrogen accumulation of rice crops (cultivars Koshihikari, Hanaechizen, Nipponbare, and IR-36) from the maximum tiller number stage to the meiosis stage, using plant-canopy reflectance of hyper-spectra within the 400-1100 nm domain without any variable selection. The results showed that the principal component regression using hyper-spectra gave better fits and predictability than that using specific wavelengths. On the other hand, partial least squares regression was the most useful among the models tested; this method avoided overfitting and multicollinearity by using all wavelength information without variable selection and by inclusion of both x and y variations in its latent variables. (author)

  17. 20% Efficient Zn0.9Mg0.1O:Al/Zn0.8Mg0.2O/Cu(In,Ga)(S,Se)2 Solar Cell Prepared by All-Dry Process through a Combination of Heat-Light-Soaking and Light-Soaking Processes.

    Science.gov (United States)

    Chantana, Jakapan; Kato, Takuya; Sugimoto, Hiroki; Minemoto, Takashi

    2018-04-04

    Development of Cd-free Cu(In,Ga)(S,Se) 2 (CIGSSe)-based thin-film solar cells fabricated by an all-dry process is intriguing to minimize optical loss at a wavelength shorter than 520 nm owing to absorption of the CdS buffer layer and to be easily integrated into an in-line process for cost reduction. Cd-free CIGSSe solar cells are therefore prepared by the all-dry process with a structure of Zn 0.9 Mg 0.1 O:Al/Zn 0.8 Mg 0.2 O/CIGSSe/Mo/glass. It is demonstrated that Zn 0.8 Mg 0.2 O and Zn 0.9 Mg 0.1 O:Al are appropriate as buffer and transparent conductive oxide layers with large optical band gap energy values of 3.75 and 3.80 eV, respectively. The conversion efficiency (η) of the Cd-free CIGSSe solar cell without K-treatment is consequently increased to 18.1%. To further increase the η, the Cd-free CIGSSe solar cell with K-treatment is next fabricated and followed by posttreatment called the heat-light-soaking (HLS) + light-soaking (LS) process, including HLS at 110 °C followed by LS under AM 1.5G illumination. It is disclosed that the HLS + LS process gives rise to not only the enhancement of carrier density but also the decrease in the carrier recombination rate at the buffer/absorber interface. Ultimately, the η of the Cd-free CIGSSe solar cell with K-treatment prepared by the all-dry process is enhanced to the level of 20.0%.

  18. Bone regeneration: in vitro evaluation of the behaviour of osteoblast-like MG63 cells placed in contact with polylactic-co-glycolic acid, deproteinized bovine bone and demineralized freeze-dried bone allograft.

    Science.gov (United States)

    Pappalardo, S; Mastrangelo, F; Reale Marroccia, D; Cappello, V; Ciampoli, C; Carlino, V; Tanteri, L; Costanzo, M; Sinatra, F; Tetè, S

    2008-01-01

    Insufficient bone density of the alveolar crests, caused by loss of the dental elements, sometimes impedes the primary stability of an integrated bone implant. The techniques of bone regeneration allow to obtain a sufficient quantity of alveolar bone to permit the implant rehabilitation of the edentulous crests. Today several grafting materials are available and they have different characteristics, according to their structure, which influence the different behaviour of the grafting materials to the bone and the implant surface. The aim of this study is to evaluate the interaction between a human osteosarcoma MG63 cell line and three different biomaterials: polylactic-co-glycolic acid (PLAGA), deproteinized bovine bone and demineralised freeze-dried bone allograft (DFDBA). From this study a different behaviour emerges of the osteoblast-like MG63 cells in relation to the sublayer on which these cells were placed in culture. The results of the study, in fact, demonstrate that the most osteoconductive material of the three analysed is the DFDBA, followed by DPBB. On the contrary, the PLGA, because of its roughness, does not seem to represent a valid support for cell growth, and does not encourage any morphologic modification in tumor cells. Furthermore, deproteinized bovine bone shows a differentiating effect which could lead to hypothesise an osteoconductive capacity of this biomaterial. Further studies should be carried out with the aim of explaining the results obtained.

  19. Produção de matéria seca e eficiência nutricional para P, Ca e Mg em leguminosas herbáceas Dry matter production and nutritional efficiency for P, Ca and Mg in herbaceous legumes

    Directory of Open Access Journals (Sweden)

    Antonio Rodrigues Fernandes

    2007-06-01

    Full Text Available As leguminosas para adubação verde têm sido introduzidas nos sistemas agrícolas para a recuperação de solos desgastados pelo uso intensivo. O objetivo desse trabalho foi avaliar a resposta de leguminosas herbáceas à aplicação de calcário e fósforo sobre a produção de biomassa e eficiência nutricional para o P, Ca e Mg. O experimento foi desenvolvido em casa-de-vegetação do Departamento de Ciência do Solo da Universidade Federal Rural da Amazônia, utilizando-se um Latossolo Amarelo distrófico coletado na profundidade de 0 - 20 cm, em Belém, PA. O delineamento experimental usado foi o de blocos ao acaso, com arranjo de tratamentos em um fatorial 3³, onde foram comparadas três espécies de leguminosas: mucuna preta (Stizolobium atterrimum, mucuna cochinchinensis (Stilozobium cochinchinensis e feijão-de-porco (Canavalia ensiformes; três níveis de calagem: de calcário dolomítico (0, 4 e 8 t.ha-1 e de fósforo (0, 25 e 45 mg.dm-3, com quatro repetições cada um. Mucuna cochinchinensis e o feijão de porco produziram maiores quantidades de biomassa vegetal do que a mucuna preta, sendo que a primeira espécie acumulou maior quantidade de P e a segunda maior quantidade de Ca. Mucuna cochinchinensis apresentou maior eficiência de utilização de P, Ca e Mg na ausência da calagem. Nos solos intemperizados com baixa concentração de P, Ca e Mg, o feijão-de-porco e a mucuna cochinchinensis poderão ter melhor desempenho do que a mucuna preta, visto que apresentaram maior eficiência de translocação e de utilização desses nutrientes, respectivamente.The legumes used for green manure have been introduced in agricultural systems for recovering degraded soils by intensive use. The objective of this work was to evaluate the response of herbaceous legumes to liming and P application on dry matter and its nutritional efficiency. The experiment was developed in greenhouse at the Soil Science Department of the Federal University

  20. Effects of drying on caffeoylquinic acid derivative content and antioxidant capacity of sweet potato leaves

    Directory of Open Access Journals (Sweden)

    Toong Long Jeng

    2015-12-01

    Full Text Available Caffeoylquinic acid (CQA derivatives are known to possess antioxidative potential and have many beneficial effects on human health. The present study compared the CQA contents and antioxidant activities of aerial parts of sweet potato plants. The effects of drying methods (freeze drying, and drying at 30°C, 70°C, and 100°C on these two parameters of the first fully expanded leaves were also assessed. The results indicated that the CQA derivatives were detectable in leaves, stem, and flowers of sweet potato plants (varied from 39.34 mg/g dry weight to 154.05 mg/g dry weight, with the leaves (particularly expanding and first fully expanded leaves containing more CQA derivatives than other aerial plant parts. The expanding and first fully expanded leaves also exhibited greater antioxidant activities than other aerial plant parts, possibly due to their higher contents of CQA derivatives. Drying method significantly affected the content of CQA derivatives in dried sweet potato leaf tissues. Drying treatments at both 70°C and 100°C significantly reduced the CQA derivative content and antioxidant activity in the first fully expanded leaves. Among the tested drying methods, the freeze-drying method demonstrated the preservation of the highest amount of CQA derivatives (147.84 mg/g and antioxidant property. However, 30°C cool air drying was also a desirable choice (total CQA derivative content was reduced to only 129.52 mg/g, compared to 70°C and 100°C hot air drying, for commercial-scale processing of sweet potato leaves, if the higher operation cost of freeze drying was a major concern.

  1. Effects of drying on caffeoylquinic acid derivative content and antioxidant capacity of sweet potato leaves.

    Science.gov (United States)

    Jeng, Toong Long; Lai, Chia Chi; Liao, Ting Chen; Lin, Su Yue; Sung, Jih Min

    2015-12-01

    Caffeoylquinic acid (CQA) derivatives are known to possess antioxidative potential and have many beneficial effects on human health. The present study compared the CQA contents and antioxidant activities of aerial parts of sweet potato plants. The effects of drying methods (freeze drying, and drying at 30°C, 70°C, and 100°C) on these two parameters of the first fully expanded leaves were also assessed. The results indicated that the CQA derivatives were detectable in leaves, stem, and flowers of sweet potato plants (varied from 39.34 mg/g dry weight to 154.05 mg/g dry weight), with the leaves (particularly expanding and first fully expanded leaves) containing more CQA derivatives than other aerial plant parts. The expanding and first fully expanded leaves also exhibited greater antioxidant activities than other aerial plant parts, possibly due to their higher contents of CQA derivatives. Drying method significantly affected the content of CQA derivatives in dried sweet potato leaf tissues. Drying treatments at both 70°C and 100°C significantly reduced the CQA derivative content and antioxidant activity in the first fully expanded leaves. Among the tested drying methods, the freeze-drying method demonstrated the preservation of the highest amount of CQA derivatives (147.84 mg/g) and antioxidant property. However, 30°C cool air drying was also a desirable choice (total CQA derivative content was reduced to only 129.52 mg/g), compared to 70°C and 100°C hot air drying, for commercial-scale processing of sweet potato leaves, if the higher operation cost of freeze drying was a major concern. Copyright © 2014. Published by Elsevier B.V.

  2. Effect of Different Fertilization Systems (Chemical, Biological and Integrated( on Nitrogen and Phosphorus Concentration, Biochemical Attributes and Sepals Dry Weight of Roselle (Hibiscus sabdariffa L.

    Directory of Open Access Journals (Sweden)

    roghayeh mohammadpour vashvaei

    2017-12-01

    and 75 kg.h-1 of urea, triple super phosphate and potassium sulphate, respectively, bio-phosphate, bio-phosphate + 25% NPK, bio-phosphate + 50% NPK, bio-phosphate + 100% NPK, nitroxin, nitroxin + 25%NPK, nitroxin + 50%NPK, nitroxin + 100%NPK, nitroxin + bio-phosphate, nitroxin + biophosphate + 25% NPK, nitroxin + biophosphate + 50% NPK, nitroxin + biophosphate + 100% NPK and control (non-use of any fertilizer. Plant traits such as leaf nitrogen and protein, sepal nitrogen and protein, leaf and sepal phosphorus, sepal anthocyanin and vitamin C content, sepal acidity and sepal dry weight of roselle were measured. For statistical analysis, combined analysis of variance, Duncan’s multiple range test (DMRT, simple correlation analysis and principal component analysis were performed using SAS version 9.2 (SAS Institute Inc., Cary, NC, USA. Results and Discussion The results of combined analysis of variance of two years showed that the effects of different treatments of chemical fertilizers, bio-fertilizers and their combinations were significant (P≤0.01 for all studied traits. The highest values of all studied traits belong to the nitroxin + biophosphate + 100% NPK treatment that its difference with nitroxin + biophosphate + 50% NPK treatment was not significant, except for leaf nitrogen and protein. Dry weight of sepals had positive, strong and very significant correlation to the percentage of nitrogen, phosphorous and protein of leaves and sepals. Principal component analysis was extracted two components that justified 83.71 and 7.50% of the total variation. According to weight of the included characteristics, these two components were named to the “yield” and “quality”. Based on the diagram of principal component analysis, treatment "Nitroxin + biophosphate + 50% NPK" was achieved maximum yield and quality of roselle. Conclusion The use of 50% of the recommended dose of fertilizers with nitroxin and bio-phosphate bio-fertilizers improved plant growth and

  3. The diagnostic accuracy of physical examination compared to lung ultrasound for determining lung congestion in hemodialysis patients who have reached their dry weight

    Science.gov (United States)

    Rahardjo, K. D.; Dharmaeizar; Nainggolan, G.; Harimurti, K.

    2017-08-01

    Research has shown that hemodialysis patients with lung congestion have high morbidity and mortality. Patients were assumed to be free of lung congestion if they had reached their post-dialysis dry weight. Most often, to determine if the patient was free of lung congestion, physical examination was used. However, the accuracy of physical examination in detecting lung congestion has not been established. To compare the capabilities of physical examination and lung ultrasound in detection of lung congestion, cross-sectional data collection was conducted on hemodialysis patients. Analysis was done to obtain proportion, sensitivity, specificity, positive predictive value, negative predictive value, and positive likelihood ratio. Sixty patients participated in this study. The inter observer variation of 20 patients revealed a kappa value of 0.828. When all 60 patients were taken into account, we found that 36 patients (57.1%) had lung congestion. Mild lung congestion was found in 24 (38.1%), and 12 (19%) had a moderate degree of congestion. In the analysis comparing jugular venous pressure to lung ultrasound, we found that sensitivity was 0.47 (0.31-0.63), specificity was 0.73 (0.54-0.86), positive predictive value (PPV) was 0.51 (0.36-0.67), negative predictive value (NPV) was 0.70 (0.49-0.84), positive likelihood ratio (PLR) was 1.75 (0.88-3.47), and the negative likelihood ratio (NLR) was 0.72 (0.47-1.12). In terms of lung auscultation, we found that sensitivity was 0.56 (0.39-0.71), specificity was 0.54 (0.35-0.71), PPV was 0.61 (0.44-0.76), NPV was 0.48 (0.31-0.66), PLR was 1.21 (0.73-2.0), and NLR was 0.82 (0.49-1.38). The results of our study showed that jugular venous distention and lung auscultation examination are not reliable means of detecting lung congestion.

  4. Specific features of the structure and weight loss of aliovalent-substituted oxides based on lanthanum gallate (La,Sr)(Ga,Fe,Mg)O3-y

    International Nuclear Information System (INIS)

    Ivanov, S. A.; Kaleva, G. M.; Aleksandrovskii, V. V.; Politova, E. D.; Eriksson, S.

    2006-01-01

    The structure of the (La 0.9 Sr 0.1 )(Ga 0.56 Fe 0.24 Mg 0.20 )O 2.85+y oxide is investigated using neutron powder diffraction at temperatures of 10, 295, and 1000 K. The results of the structure refinement are in good agreement with the dilatometric and thermogravimetric data and confirm the inference that the valence state of iron cations is higher than 3+ and that the lattice undergoes an additional expansion due to the oxygen loss at temperatures above 870 K

  5. Dry Eye

    Science.gov (United States)

    ... Eye » Facts About Dry Eye Listen Facts About Dry Eye Fact Sheet Blurb The National Eye Institute (NEI) ... and their families search for general information about dry eye. An eye care professional who has examined the ...

  6. Quality of pomegranate pomace as affected by drying method.

    Science.gov (United States)

    Cano-Lamadrid, Marina; Lech, Krzysztof; Calín-Sánchez, Ángel; Rosas-Burgos, Ema Carina; Figiel, Adam; Wojdyło, Aneta; Wasilewska, Malwina; Carbonell-Barrachina, Ángel A

    2018-03-01

    During the industrial manufacturing of pomegranate juice, large amounts of pomace are produced. The aim of this work was to find the effective method to dry pomegranate pomace to open new commercial applications for this co-product. The effects of three drying methods: (i) convective drying (CD) at 50, 60, and 70 °C; (ii) vacuum microwave drying (VMD) at 240, 360, and 480 W, and (iii) a combined method (CPD-VMFD); convective pre-drying (60 °C) followed by vacuum microwave finish drying (360 W), on drying kinetics and quality of PomP (pomegranate pomace obtained after preparing pomegranate juice by squeezing only arils) were evaluated. The shortest treatments were VMD at 240 and 360 W (52 and 33 min, respectively); besides, these treatments led to interesting values of the green-red coordinate, a *, (12.2 and 4.1, respectively), total phenolic content (4.0 and 4.1 mg eq gallic acid g -1  dry weight, respectively), and antioxidant activity (30.8 and 29.0 µmol g -1  dry weight, respectively). On the other hand, this study demonstrated that this co-product is a rich source of punicic acid (average value = 66.4%), being a good opportunity for the pharmaceutical and nutraceutical industries. Moreover, no significant changes in the fatty acid profile was observed as affected by the drying treatments, and no off-flavors were generated by any of the drying methods.

  7. Acute and chronic toxicity studies of the water extract from dried ...

    African Journals Online (AJOL)

    Acute and chronic toxicities of the water extract from the dried fruits of Terminalia bellerica (Gaertn.) Roxb. were assessed in both female and male rats. For the study of acute toxicity, a single oral administration of the water extract at a dose of 5,000 mg/kg body weight (10 female, 10 male) was performed and the results ...

  8. Herbal dryer: drying of ginger (zingiber officinale) using tray dryer

    Science.gov (United States)

    Haryanto, B.; Hasibuan, R.; Alexander; Ashari, M.; Ridha, M.

    2018-02-01

    Drying is widely used as a method to preserve food because of its convenience and affordability. Drying of ginger using tray dryer were carried out at various drying conditions, such as air-drying flow, air-drying temperature, and sample dimensions, to achieve the highest drying rate. Samples with various dimensions were placed in the tray dryer and dried using various air-drying flow and temperatures. The weights of samples were observed every 3 minutes interval. Drying was stopped after three times of constant weighing. Data of drying was collected to make the drying curves. Drying curves show that the highest drying rate is achieved using highest air flow and temperature.

  9. The iron content and ferritin contribution in fresh, dried, and toasted nori, Pyropia yezoensis.

    Science.gov (United States)

    Masuda, Taro; Yamamoto, Ami; Toyohara, Haruhiko

    2015-01-01

    Iron is one of the essential trace elements for humans. In this study, the iron contents in fresh, dried, and toasted nori (Pyropia yezoensis) were analyzed. The mean iron content of fresh, dried, and toasted nori were 19.0, 22.6, and 26.2 mg/100 g (dry weight), respectively. These values were superior to other food of plant origin. Furthermore, most of the iron in nori was maintained during processing, such as washing, drying, and toasting. Then, the form of iron in fresh, dried, and toasted nori was analyzed. As a result, an iron storage protein ferritin contributed to iron storage in raw and dried nori, although the precise rate of its contribution is yet to be determined, while ferritin protein cage was degraded in the toasted nori. It is the first report that verified the ferritin contribution to iron storage in such edible macroalgae with commercial importance.

  10. Dry socket

    Science.gov (United States)

    Alveolar osteitis; Alveolitis; Septic socket ... You may be more at risk for dry socket if you: Have poor oral health Have a ... after having a tooth pulled Have had dry socket in the past Drink from a straw after ...

  11. Evaluación del peso seco y el agua corporal según bioimpedancia vectorial frente al método tradicional Assessing dry weight and body water using bioimpedance vector analysis compared to the traditional method

    Directory of Open Access Journals (Sweden)

    María Teresa Centellas Tristán

    2013-03-01

    , los resultados mostraron variaciones poco significativas de los parámetros estudiados. Conclusiones: Aunque la bioimpedancia aporta conocimientos más exactos sobre la composición hídrica corporal y la distribución del agua, el peso seco establecido por estimación clínica sigue siendo de gran valor. La bioimpedancia ayuda a detectar pequeños cambios subclínicos, que podrían tener trascendencia a más largo plazo. La bioimpedancia pone de manifiesto de forma objetiva la desnutrición presente en casi la mitad de pacientes de hemodiálisis.Introduction: Electrical bioimpedance can be used to establish the hydration and nutritional state in haemodialysis. Assessing the hydration status of patients is habitually done as a "clinical art" using the concept of "dry weight". There are few studies that examine the concordance between dry weight estimated clinically and the dry weight deduced post-bioimpedance analysis. Material and methods: 36 patients were studied (26 men and 10 women. Electrical bioimpedance vector analysis was performed before and 30' after midweek dialysis, measuring weight, total water and its distribution, phase angle, Na/K ratio, and the position of each patient's vector in the sphere normogram: percentiles 50.75 and 95. Dry weight was estimated according to the subjective assessment of the nephrologist, nurse and patient. Furthermore, in 12 stable patients the bioimpedance analysis continued for 4 weeks. Results: The age was 69.6±12.5 (r=29-89. Weight was 73.1±14.1 predialysis, and 70.4±13.6 postdialysis. Total body water was 24.7±2.8 L/m (53.7±8.2% of weight; 22.1±3.0 L (56.2±5.9% of weight corresponded to extracellular water and 17.4±3.8 L/m to intracellular water. Following haemodialysis, total water fell to 22.8±2.4 L/m (51.8±8.6% of weight (23.5±2.2 L in men; and 21.5±3 L in women of which 19.6±2.5 L (54.3±5.8% of weight corresponded to extracellular water and 16.7±3.3 to intracellular water. One man and 5 women exceeded

  12. Antioxidant capacity and polyphenolic content of dried wild edible mushrooms from Poland.

    Science.gov (United States)

    Radzki, Wojciech; Sławińska, Aneta; Jabłońska-Ryś, Ewa; Gustaw, Waldemar

    2014-01-01

    In this study 6 species of wild edible mushrooms were evaluated in terms of their total phenolic content and antioxidant activity using 1,1-diphenyl-2-picrylhydrazyl radical and ferric reducing antioxidant power assay methods. The mushrooms, namely Armillaria mellea, Cantharellus cibarius, Lactarius deliciosus, Leccinum aurantiacum, Suillus luteus, and Boletus badius, were dried using both freeze drying and convection drying at 50°C. The amounts of phenolic compounds varied from 3.0 ± 0.1 to 12.8 ± 0.4 mg gallic acid equivalents/g dry weight (for water extracts) and from 2.4 ± 0.1 to 11 ± 0.5 mg gallic acid equivalents/g dry weight (for ethanolic extracts). The species that presented the highest antioxidant potential were B. badius and S. luteus. The impact of hot-air drying on the antioxidant activity of water and ethanolic extracts was evaluated. We demonstrated that hot-air drying may have either a negative or positive influence on phenolics and antioxidant activity, depending on the mushroom species. However, a negative effect was more frequent.

  13. Infrared Drying as a Quick Preparation Method for Dried Tangerine Peel

    Directory of Open Access Journals (Sweden)

    Mingyue Xu

    2017-01-01

    Full Text Available To establish the most convenient and effective method to dry tangerine peels, different methods (sun drying, hot-air drying, freeze drying, vacuum drying, and medium- and short-wave infrared drying were exploited. Our results indicated that medium- and short-wave infrared drying was the best method to preserve nutraceutical components; for example, vitamin C was raised to 6.77 mg/g (D.W. from 3.39 mg/g (sun drying. Moreover, the drying time can be shortened above 96% compared with sun drying. Importantly, the efficiency of DPPH radical scavenging was enhanced from 26.66% to 55.92%. These findings would provide a reliable and time-saving methodology to produce high-quality dried tangerine peels.

  14. Dry Etching

    DEFF Research Database (Denmark)

    Stamate, Eugen; Yeom, Geun Young

    2016-01-01

    generation) to 2,200 × 2,500 mm (eighth generation), and the substrate size is expected to increase further within a few years. This chapter aims to present relevant details on dry etching including the phenomenology, materials to be etched with the different recipes, plasma sources fulfilling the dry...

  15. Efeito do alumínio sobre o crescimento de raízes, peso seco da parte aérea e raízes de diferentes cultivares de soja Effect of aluminum on root growth, dry matter weight of the above ground parts and roots of soybeans

    Directory of Open Access Journals (Sweden)

    Hipolito Assunção Antonio Mascarenhas

    1984-01-01

    Full Text Available Foram instalados dois experimentos preliminares, em solução nutritiva, para avaliar a tolerância da soja ao alumínio. No primeiro, foram testados os cultivares Cristalina e UFV-1, utilizando-se os teores 0, 5, 10 e 20mg/litro de Al. Esses níveis foram muito altos e reduziram drasticamente o comprimento das raízes primarias das plântulas após sete dias de crescimento. Com base nesses dados, outro experimento foi instalado, testando os cultivares Lee, Bragg, Cristalina e UFV-1. a 0, 1, 2 e 4mg/litro de Al. Os resultados mostraram que o comprimento das raízes primárias das plântulas foi melhor parâmetro do que o peso seco da parte aérea ou das raízes, para avaliar tolerância de soja ao alumínio. O nível de 1mg/litro na solução foi suficiente para separar os cultivares susceptíveis e tolerantes, enquanto os níveis de 2 e 4mg/litro causaram drástica redução do comprimento de raiz primária das plântulas de todos os cultivares. Nessas condições, 'Lee' e 'Cristalina' mostraram ser tolerantes enquanto o 'Bragg' se apresentou intermediário e o 'UFV-1' foi o mais susceptível entre eles. Os cultivares tolerantes revelaram tendência de acumular menores teores de Al na parte aérea, em comparação com os demais.Two experiments were conducted in nutrient solution to study the level of Al necessary to separate tolerant cultivars from the susceptible. In the first experiment the levels of Al were 0, 5, 10 and 20mg/l and two cultivars Cristalina and UFV-1 were studied. These levels were found to be too high as they had drastic effect on the primary roots after 7 days of transplanting. Based on this data another experiment was conducted using 0, 1, 2 and 4mg/l of Al and using cultivars Lee, Bragg, Cristalina and UFV-1. The results showed that the length of the primary root was the best parameter as compared with dry weight of the above ground parts and roots to evaluate tolerance of soybeans to Al. The level of 1mg/l was adequate to

  16. Crescimento , produção de matéria seca e acúmulo de N, P, K, Ca, Mg e S na parte aérea de mudas de andiroba (Carapa guianensis Aubl. cultivadas em solo de várzea, em função de diferentes doses de fósforo Growth, dry matter yield and N, P, K, Ca, Mg and S accumulation in andiroba seedling shoots (Carapa guianensis Aubl. cultivated in lowland soil, in function of phosphorus doses

    Directory of Open Access Journals (Sweden)

    Orlando Sílvio Caires Neves

    2004-06-01

    Full Text Available Com o objetivo de avaliar o efeito de diferentes doses de fósforo no crescimento e produção de matéria seca e acúmulo de N, P, K, Ca, Mg e S na parte aérea de mudas de andiroba, cultivadas em solo de várzea, foi conduzido um experimento em casa de vegetação, no Departamento de Ciências do Solo (DCS da Universidade Federal de Lavras (UFLA. O delineamento utilizado foi em blocos casualizados com cinco repetições e quatro doses de fósforo (0, 150, 300 e 450 mg dm-3 de P. Foram avaliados diâmetro do caule (mm, altura de plantas (cm, matéria seca de raiz, caule, folha e total (g planta-1. A partir dos teores dos elementos, determinou-se o acúmulo dos nutrientes com base na matéria seca. A máxima resposta física da planta de andiroba à adubação fosfatada foi obtida na faixa de 239 a 265 mg dm-3 de P. O máximo acúmulo de N, P, K, Ca, Mg e S foi atingido com as doses de 254; 287,5; 244,5; 254; 241; e 275 mg dm-3 de P, respectivamente. Os elementos em estudo que mais acumularam na parte aérea das mudas de andiroba seguem a seguinte ordem decrescente: N > Ca > K > Mg > S > P.To evaluate the effect of phosphorus application on growth, dry matter yield and N, P, K, Ca, Mg and S accumulation in "andiroba" seedling shoots, cultivated in lowland soil, an experiment was conducted under greenhouse conditions at the Soil Science Department (DCS of the Federal University of Lavras (UFLA. The experiment was conducted in a randomized block design, with five replications and four phosphorus doses (0, 150, 300 and 450 mg dm-3 of P. Stem diameter (mm, plant height (cm, root dry matter, stem, leafs and total (g plant-1 were evaluated and the accumulation of the nutrients based on dry matter was determined. The maximum physical response of andiroba to phosphorus was obtained between 239 to 265 mg dm-3 of P. The maximum accumulation of N, P, K, Ca, Mg and S was observed with the doses 254, 287,5, 244,5, 254, 241 and 275 mg dm-3 of P, respectively

  17. Dry cell battery poisoning

    Science.gov (United States)

    Batteries - dry cell ... Acidic dry cell batteries contain: Manganese dioxide Ammonium chloride Alkaline dry cell batteries contain: Sodium hydroxide Potassium hydroxide Lithium dioxide dry cell batteries ...

  18. Light-weight plastination.

    Science.gov (United States)

    Steinke, Hanno; Rabi, Suganthy; Saito, Toshiyuki; Sawutti, Alimjan; Miyaki, Takayoshi; Itoh, Masahiro; Spanel-Borowski, Katharina

    2008-11-20

    Plastination is an excellent technique which helps to keep the anatomical specimens in a dry, odourless state. Since the invention of plastination technique by von Hagens, research has been done to improve the quality of plastinated specimens. In this paper, we have described a method of producing light-weight plastinated specimens using xylene along with silicone and in the final step, substitute xylene with air. The finished plastinated specimens were light-weight, dry, odourless and robust. This method requires less use of resin thus making the plastination technique more cost-effective. The light-weight specimens are easy to carry and can easily be used for teaching.

  19. DETERMINATION OF A MATHEMATICAL MODEL TO ESTIMATE THE AREA AND DRY WEIGHT OF THE LEAF LIMBO OF Prunus persica CV. Jarillo DETERMINACIÓN DE UN MODELO MATEMÁTICO PARA LA ESTIMACIÓN DEL ÁREA FOLIAR Y PESO SECO DEL LIMBO DE Prunus persica CV. Jarillo

    Directory of Open Access Journals (Sweden)

    Enrique Quevedo García

    2012-06-01

    Full Text Available Abstract. A study was conducted to determine the variables that estimated the leaf limbo area and the leaf limbo dry weight of peach Prunus persica (L. Batsch cv. Jarillo. Fifty leaves, aged 2.5 months, were selected and measured: leaf limbo length and width, petiole length, leaf length, petiole diameter, leaf limbo fresh weight, petiole fresh weight, leaf fresh weight, leaf limbo dry weight, petiole dry weight, leaf dry weight, length/width limbo, petiole length/limbo length and leaf limbo area. The results allowed to obtain regression equations for estimating the leaf area and the limbo dry weight. Using the lineal models LA = b1 + b2 (LLL x LLW and LA= b1+ b2LLL + b3LLW a leaf area equation was determined. Alternative models to calculate limbo dry weight were evaluated LLDW = -b1+ b2 LLFW and LLDW= - b1 + b2LLL + b3PL. The best equations found with an R2 of 0.99 were LA = 1.572 + 0.65169(LLL x LLW, LA=-23.106+2.8064LLW + 3.6761LLL and LLDW = -0.002+0.401(LLFW.Resumen. Se realizó un estudio para determinar las variables que estimaran el área del limbo foliar y el peso seco del limbo de durazno Prunus persica (L. Batsch cv. Jarillo. Se seleccionaron cincuenta hojas con 2,5 meses de edad, fueron medidos: ancho del limbo, longitud del limbo, longitud del peciolo, longitud hoja, diámetro peciolo, peso fresco del limbo, peso fresco del peciolo, peso fresco de la hoja, peso seco del limbo, peso seco peciolo, peso seco de la hoja, longitud /ancho limbo, longitud del peciolo/longitud del limbo, área foliar del limbo. Los resultados alcanzados permitieron obtener ecuaciones de regresión para estimar el área foliar del limbo y el peso seco del limbo. Se halló una ecuación para la determinación del área foliar del limbo con los modelos lineales LA = b1 + b2 (LLL x LLW y LA= b1 + b2LLL + b3LLW. También se evaluaron modelos alternativas para calcular el peso seco del limbo, LLDW = -b1+ b2LLFW y LLDW= - b1 + b2LLL + b3PL. Las mejores ecuaciones

  20. Antioxidant, Antinociceptive, and Anti-Inflammatory Effects of Carotenoids Extracted from Dried Pepper (Capsicum annuum L.)

    Science.gov (United States)

    Hernández-Ortega, Marcela; Ortiz-Moreno, Alicia; Hernández-Navarro, María Dolores; Chamorro-Cevallos, Germán; Dorantes-Alvarez, Lidia; Necoechea-Mondragón, Hugo

    2012-01-01

    Carotenoids extracted from dried peppers were evaluated for their antioxidant, analgesic, and anti-inflammatory activities. Peppers had a substantial carotenoid content: guajillo 3406 ± 4 μg/g, pasilla 2933 ± 1 μg/g, and ancho 1437 ± 6 μg/g of sample in dry weight basis. A complex mixture of carotenoids was discovered in each pepper extract. The TLC analysis revealed the presence of chlorophylls in the pigment extract from pasilla and ancho peppers. Guajillo pepper carotenoid extracts exhibited good antioxidant activity and had the best scavenging capacity for the DPPH+ cation (24.2%). They also exhibited significant peripheral analgesic activity at 5, 20, and 80 mg/kg and induced central analgesia at 80 mg/kg. The results suggest that the carotenoids in dried guajillo peppers have significant analgesic and anti-inflammatory benefits and could be useful for pain and inflammation relief. PMID:23091348

  1. Dry storage

    International Nuclear Information System (INIS)

    Arnott, Don.

    1985-01-01

    The environmental movement has consistently argued against disposal of nuclear waste. Reasons include its irretrievability in the event of leakage, the implication that reprocessing will continue and the legitimacy attached to an expanding nuclear programme. But there is an alternative. The author here sets out the background and a possible future direction of a campaign based on a call for dry storage. (author)

  2. The influence of lysozyme on mannitol polymorphism in freeze-dried and spray-dried formulations depends on the selection of the drying process

    DEFF Research Database (Denmark)

    Grohganz, Holger; Lee, Yan-Ying; Rantanen, Jukka

    2013-01-01

    Freeze-drying and spray-drying are often applied drying techniques for biopharmaceutical formulations. The formation of different solid forms upon drying is often dependent on the complex interplay between excipient selection and process parameters. The purpose of this study was to investigate...... the influence of the chosen drying method on the solid state form. Mannitol-lysozyme solutions of 20mg/mL, with the amount of lysozyme varying between 2.5% and 50% (w/w) of total solid content, were freeze-dried and spray-dried, respectively. The resulting solid state of mannitol was analysed by near......-dried formulations an increase in protein concentration resulted in a shift from ß-mannitol to a-mannitol. An increase in final drying temperature of the freeze-drying process towards the temperature of the spray-drying process did not lead to significant changes. It can thus be concluded that it is the drying...

  3. Drying Spirulina with Foam Mat Drying at Medium Temperature

    Directory of Open Access Journals (Sweden)

    Aji Prasetyaningrum

    2012-10-01

    Full Text Available Spirulina is a single cell blue green microalgae (Cyanobacteria containing many Phytonutrients (Beta-carotene, Chlorophyl, Xanthophyl, Phyocianin using as anti-carcinogen in food. Producing dry spirulina by quick drying process at medium temperature is very important to retain the Phytonutrient quality. Currently, the work is still challenging due to the gel formation that block the water diffusion from inside to the surface.  This research studies the performance of foam-mat drying on production of dry spirulina. In this method the spirulina was mixed with foaming agent (glair/egg albumen, popular as white egg at 2.5% by weight at air velocity 2.2 m/sec. Here, the effect of spirulina thickness and operational temperature on drying time and quality (Beta-carotene and color were observed. The drying time was estimated based on the measurement of water content in spirulina versus time. Result showed that the thicker spirulina, the longer drying time. Conversely, the higher operational temperature, faster drying time. At thickness ranging 1-3 mm and operational temperature below 70oC, the quality of spirulina can fit the market requirement

  4. Microwave wood strand drying: energy consumption, VOC emission and drying quality

    Energy Technology Data Exchange (ETDEWEB)

    Wang, S.; Du, G.; Zhang, Y. [Tennessee Univ., Knoxville, TN (United States). Dept. of Forestry, Wildlife and Fisheries

    2005-07-01

    The objective of this research was to develop microwave drying technology for wood strand drying for oriented strand board (OSB) manufacturing. The advantages of microwave drying included a reduction in the drying time of wood strands and a reduction in the release of volatile organic compounds (VOC) through a decrease in the thermal degradation of the wood material. Temperature and moisture content changes under different microwave drying conditions were investigated. The effects of microwave drying on VOC emissions were evaluated and analyzed using gas chromatography and mass spectrometry. Microwave power input and the mass of drying materials in the microwave oven were found to have a dominant effect on drying quality. Results indicated that an increase in microwave power input and a decrease in sample weights resulted in high drying temperatures, short drying times and a high drying rate. The effect of microwave drying on the strand surfaces was also investigated. Different strand geometries and initial moisture content resulted in varying warm-up curves, but did not influence final moisture content. VOC emissions were quantified by comparing alpha-pinene concentrations. The microwave drying resulted in lower VOC emissions compared with conventional drying methods. It was concluded that the microwave drying technique provided faster strand drying and reduced energy consumption by up to 50 per cent. In addition, the surface wettability of wood strands dried with microwaves was better than with an industrial rotary drum drier. 12 refs., 3 tabs., 5 figs.

  5. Evaluation of drying methods with respect to drying parameters, some nutritional and colour characteristics of peppermint (Mentha x piperita L.)

    International Nuclear Information System (INIS)

    Arslan, Derya; Ozcan, M. Musa; Menges, Hakan Okyay

    2010-01-01

    Peppermint leaves (Mentha x piperita L.) were dried by using sun, oven (50 deg. C) and microwave oven (700 W) drying methods. Page, Modified page, Midilli and Kuecuek models adequately described the oven, sun and microwave oven drying behaviours of peppermint leaves. The drying process was explicated through the diffusional model in order to obtain effective diffusivity values, which were determined as 3.10 x 10 -12 , 2.68 x 10 -12 and 4.09 x 10 -10 for the sun, oven and microwave oven drying process, respectively. Fresh and dried herbs had high amounts of K, Ca, P, Mg, Fe and Al minerals. Microwave oven drying method leaded to the lowest increase in Ag, Al, B, Na, Mn, Mg and Zn values than the other drying methods. Microwave oven drying shortened the drying time, revealed the highest phenolic content and optimum colour values.

  6. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Stories Español Eye Health / Eye Health A-Z Dry Eye Sections What Is Dry Eye? Dry Eye Symptoms ... of Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué es el ojo seco? ...

  7. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Español Eye Health / Eye Health A-Z Dry Eye Sections What Is Dry Eye? Dry Eye Symptoms ... Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué es el ojo seco? ...

  8. Characterization of biomasses, concentrates, and permeates of dried powder of Kombucha fermentation of spinach (Amaranthus sp.) and broccoli (Brassica oleracea) with membrane microfiltration and freeze drying techniques for natural sources of folic acid

    Science.gov (United States)

    Nugraha, Tutun; Susilowati, Agustine; Aspiyanto, Lotulung, Puspa Dewi; Maryati, Yati

    2017-11-01

    Fermentation of spinach (Amaranthus sp) and Broccoli (Brassica oleracea) using Kombucha Culture has been shown to produce biomass that has the potential to become natural sources of folic acid. To produce the materials, following the fermentation, the biomass was filtered using membrane microfiltration (0.15 µm) at a pressure of 40 psia, at room temperature, yielding the concentrate and the permeate fractions. Following this step, freeze drying process was done on the biomass feeds, as well as on the concentrate and permeate fractions. For the freeze drying stage, the samples were frozen, and the condenser was kept at -50°C for 40 hours, while the pressure in the chamber was set at 200 Pa. Freeze drying results showed that the final products, have differences in compositions, as well as differences in the dominat monomers of folates. After water content was driven out, freeze drying increased the concentrations of folic acid in the dried products, and was found to be the highest in the concentrate fractions. Freeze drying has been shown to be capable of protecting the folates from heat and oxidative damages that typicaly occur with other types of drying. The final freeze dried concentrates of fermentation of spinach and broccoli were found to contain folic acid at 2531.88 µg/mL and 1626.94 µg/mL, total solids at 87.23% and 88.65 %, total sugar at 22.66 µg/mL and 25.13 µg/mL, total reducing sugar at 34.46 mg/mL and 15.22 mg/mL, as well as disolved protein concentrations at 0.93 mg/mL and 1.45 mg/mL. Liquid Chromatography Mass Spectometry (LC-MS) identification of the folates in the freeze dried concentrates of fermented spinach and broccoli was done using folic acid and glutamic acid standard solutions as the reference materials. The results showed the presence of folic acid and showed that the dominant monomers of molecules of folates with molecular weights of 441.44 Da. and 441.54 Da. for spinach and broccoli respectively. Moreover, the monomers of glutamic

  9. Solar Drying and Sensory Attributes of Eland (Taurotragus oryx Jerky

    Directory of Open Access Journals (Sweden)

    Iva Kučerová

    2018-01-01

    Full Text Available A double-pass solar drier (DPSD and a laboratory oven (LO were used for thin-layer drying of eland and beef. Prior to drying, the physicochemical characteristics of the raw meat were determined, such as pH, dry matter content (%, Warner-Bratzler shear force (N, pigment concentration (mg·kg−1, weight loss during cooking (%, water holding capacity (%, colour (L,a,b, and crude fat content (%. Both meats were pretreated with traditional jerky marinade (TM, TM with fresh pineapple juice (TMP, TM with honey (TMH, and TM with Coca Cola© (TMCCL and compared to an untreated control (C. The sensory properties of the eland and beef jerky were assessed in a two-stage process. The surface colour values of the jerky samples were measured in the CIE L⁎  a⁎  b⁎ colour space and the effect of the different pretreatments on the overall combined colour (ΔE was calculated. Significant differences (p<0.05 between raw eland and beef samples were found in case of pH, pigment concentration, water holding capacity, crude fat content, and colour (L and b. Jerky from TMP pretreated meat had the highest scores for texture, colour, and taste. Generally, for both meats dried in both driers, TMH marinade was evaluated as the one with the highest total difference ΔE compared to meat dipped in TMP pretreatment, which had the lowest total difference ΔE.

  10. Effect of green manure crops and nitrogen fertilizer levels on dry matter remobilization efficiency in wheat (Triticum aestivum L. internodes

    Directory of Open Access Journals (Sweden)

    F. Gerami

    2016-05-01

    Full Text Available In order to evaluate the effect of nitrogen rates and green manure crops on dry matter mobilization and mobilization efficiency indices of wheat (Triticum aestivum L. a field experiment was conducted in Agricultural Faculty of Shahid Chamran University, Ahvaz during growing season of 2010-2011. The experimental design was split-plot based on randomized complete block with three replications. Main plot included four nitrogen rates (i.e. 0, 50, 100 and 150 kgN.ha-1 and sub-plot included six green manure crops containing millet (Pennisetum sp., amaranth (Amaranthus sp., sesbania (Sesbania sp., cowpea (Vigna unguiculata L., mung bean (Vigna radiata L. and fallow. This experiment was done at two stages. First, planting and turn down of green manure crops and then planting of wheat. The results showed that the maximum weight and specific weight of all stem internodes obtained from 0 to 20 days after wheat anthesis. Then, this trend decreased from 20 to 50 days after wheat anthesis due to remobilization of dry matter to grain. Mobilized dry matter was more in control (0 kg.N.h-1 than in high N application for peduncle (219 vs. 181 mg and penultimate (203 vs. 165 mg, while, was less in the lower internodes (403 vs. 407 mg. Generally, with increasing of nitrogen levels, dry matter mobilization efficiency was decreased by. So, the effect of green manure crops not limited only by soil properties, while influences the relationship between physiological sources and sink.

  11. Comparative Evaluation of Sulfur Compounds Contents and Antiobesity Properties of Allium hookeri Prepared by Different Drying Methods

    Directory of Open Access Journals (Sweden)

    Min Hye Yang

    2017-01-01

    Full Text Available Despite the nutritional and medicinal values of Allium hookeri, its unique flavor (onion or garlic taste and smell coming from sulfur containing compounds limits its usage as functional food. For comparative study, A. hookeri roots were prepared under two different drying conditions, namely, low-temperature drying that minimizes the volatilization of sulfur components and hot-air drying that minimizes the garlic odor and spicy taste of A. hookeri. In GC/MS olfactory system, the odorous chemicals and organosulfur compounds such as diallyl trisulfide, dimethyl trisulfide, and dipropyl trisulfide were significantly decreased in hot-air drying compared to low-temperature drying. The spiciness and saltiness taste were noticeably reduced, while sourness, sweetness, and umami taste were significantly increased in hot-air dried A. hookeri according to electronic tongue. Although the content of volatile sulfur components was present at lower level, the administration of hot-air dried A. hookeri extract (100 mg/kg p.o. apparently prevented the body weight gain and improved insulin resistance in C57BL/6J obese mice receiving high fat diet. Results suggested that the hot-air dried A. hookeri possessing better taste and odor might be available as functional crop and bioactive diet supplement for the prevention and/or treatment of obesity.

  12. Evaluation of drying methods with respect to drying kinetics, mineral content and colour characteristics of rosemary leaves

    International Nuclear Information System (INIS)

    Arslan, Derya; Musa Ozcan, M.

    2008-01-01

    Rosemary leaves (Rosmarinus officinalis L., Lamiaceae) were dried by using sun, oven (50 deg. C) and microwave oven (700 W, 2450 MHz) drying methods. Microwave oven drying shortened the drying time more than 99% when compared to the sun and oven drying methods. K, Ca, Na, Mg and P were the most abundant elements in the rosemary samples. The mineral content of oven dried rosemary leaves was higher than that of the sun and microwave dried samples. The logarithmic and Midilli and Kuecuek models were shown to give a good fit to the sun and oven drying. The Page, Modified Page and Midilli and Kuecuek models have shown a better fit to the experimental microwave oven drying data of rosemary leaves. Microwave oven drying revealed optimum colour values. Oven drying resulted in a considerable decrease in the colour quality of the rosemary leaves

  13. Prueba de supresión con Dexametasona 1mg en una población de individuos con normopeso, sobrepeso y obesidad: Estudio multicéntrico The Overnight 1mg Dexamethasone Test in Healthy Subjects with Normal Weight, Overweight and Obesity: a Multicentric Study

    OpenAIRE

    Ester Pardes; Susana Belli; Fabiana Baña; Liliana Contreras; Estela Cardoso; Liliana Costa; Dora Cornaló; Mariela Leal; Marcela Martínez; María Teresa Nofal; Gabriela Ruibal

    2007-01-01

    La prueba de supresión con dexametasona-1mg oral nocturna evalúa la conservación del mecanismo de retroalimentación negativa normal ejercido por los glucocorticoides sobre el eje hipotálamo-hipófiso-adrenal (HH-A), siendo ampliamente utilizada en el algoritmo diagnóstico de sospecha de síndrome de Cushing (SC). Pero la concentración de cortisol sérico matinal postinhibición que define la supresiblidad normal ha sido motivo de controversia, con valores variables desde el original =5 ug/dl (=13...

  14. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Eye? Dry Eye Symptoms Causes of Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué ... Inside of Your Eyelid Nov 29, 2017 New Dry Eye Treatment is a Tear-Jerker Jul 21, 2017 Three ...

  15. What Is Dry Eye?

    Science.gov (United States)

    ... Eye? Dry Eye Symptoms Causes of Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué ... Inside of Your Eyelid Nov 29, 2017 New Dry Eye Treatment is a Tear-Jerker Jul 21, 2017 Three ...

  16. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Ophthalmology/Strabismus Ocular Pathology/Oncology Oculoplastics/Orbit Refractive Management/Intervention Retina/Vitreous Uveitis Focus On ... Dry Eye Sections What Is Dry Eye? Dry Eye Symptoms Causes of ...

  17. A comparative study of metabolism and concentration factors of Fe, Cu, Zn, Mn, Co and Mg in Carcinus maenas and Cancer irroratus ovaries during ovogenesis

    International Nuclear Information System (INIS)

    Martin, J.-L.M.

    1975-01-01

    Fe, Cu, Zn, Mn, Co, and Mg were analysed in the ovary of Carcinus maenas and Cancer irroratus during ovogenesis. In both ovaries, the relatives rates, expressed as parts per millions as a ratio of wet and dry weight, are the following: Mg>Zn>Fe>Cu>Mn>Co, while in the hemolymph of Cancer irroratus these relative rates are the following: Mg>Cu>Zn>Fe>Mn>Co. Compared to concentrations of these metals in sea water, Mg expected, all metals in the ovary of Cancer irroratus have a concentration factor upper than 1. Compared to the concentration of metals in the hemolymph is, for Fe, Mn, and Co, the concentration factor upper than 1, and for Cu, Zn and Mg, the concentration factor lower than 1. A study of correlations was done between the concentrations of metals considered in pairs, and between the concentrations of metals and the parameters: water content and gonad index [fr

  18. Recent advances in drying and dehydration of fruits and vegetables: a review

    OpenAIRE

    Sagar, V. R.; Suresh Kumar, P.

    2010-01-01

    Fruits and vegetables are dried to enhance storage stability, minimize packaging requirement and reduce transport weight. Preservation of fruits and vegetables through drying based on sun and solar drying techniques which cause poor quality and product contamination. Energy consumption and quality of dried products are critical parameters in the selection of drying process. An optimum drying system for the preparation of quality dehydrated products is cost effective as it shortens the drying ...

  19. Weight Management

    Science.gov (United States)

    ... Health Information Weight Management English English Español Weight Management Obesity is a chronic condition that affects more ... Liver (NASH) Heart Disease & Stroke Sleep Apnea Weight Management Topics About Food Portions Bariatric Surgery for Severe ...

  20. Surface fixation of dried blood by glutaraldehyde and peracetic acid.

    Science.gov (United States)

    Kampf, G; Bloss, R; Martiny, H

    2004-06-01

    The difficulties of successful prion inactivation by chemical agents has led to changes in recommendations regarding the reprocessing of instruments including flexible endoscopes. One of the changes is the preference for peracetic acid instead of glutaraldehyde in order to avoid fixation of organic material, but the surface fixation by various active agents has not been fully investigated. We used a standardized amount of dried blood soil on metal carriers (on average 22 mg). One part of the carriers was exposed to different disinfectants (four based on peracetic acid, three based on glutaraldehyde, two based on quaternary ammonium compounds (QAC), one based on QAC and amines, one based on phenols and one cleaning agent) and air dried. The difference compared with the non-exposed soiled carrier was taken as the measure of blood removal by exposure to the disinfectants. In addition the other part of the carriers was exposed to a cleaning agent and air dried. The cleaning agent itself was capable of removing more than 99% of the dried blood and served as a control for non-fixation. The rate of fixation of dried blood was calculated as the ratio of the weight of residual soil on 'soiled, disinfected and cleaned' carriers and on 'soiled and disinfected' carriers. All experiments were repeated eight times. Blood removal varied between 90.3% +/- 1.5% (phenol-based disinfectant) and peracetic acid. No other preparations showed a potential for blood fixation (peracetic acid, and support the evidence that effective cleaning should precede the chemical disinfection. Copyright 2004 The Hospital Infection Society

  1. Evaluation of the effect of alternative measurements of body weight gain and dry matter intake for the calculation of residual feed intake in growing purebred Charolais and Red Angus cattle.

    Science.gov (United States)

    Kayser, W; Glaze, J B; Welch, C M; Kerley, M; Hill, R A

    2015-07-01

    The objective of this study was to determine the effects of alternative-measurements of body weight and DMI used to evaluate residual feed intake (RFI). Weaning weight (WW), ADG, and DMI were recorded on 970 growing purebred Charolais bulls (n = 519) and heifers (n = 451) and 153 Red Angus growing steers (n = 69) and heifers (n = 84) using a GrowSafe (GrowSafe, Airdrie, Alberta, Canada) system. Averages of individual DMI were calculated in 10-d increments and compared to the overall DMI to identify the magnitude of the errors associated with measuring DMI. These incremental measurements were also used in calculation of RFI, computed from the linear regression of DMI on ADG and midtest body weight0.75 (MMWT). RFI_Regress was calculated using ADG_Regress (ADG calculated as the response of BW gain and DOF) and MMWT_PWG (metabolic midweight calculated throughout the postweaning gain test), considered the control in Red Angus. A similar calculation served as control for Charolais; RFI was calculated using 2-d consecutive start and finish weights (RFI_Calc). The RFI weaning weight (RFI_WW) was calculated using ADG_WW (ADG from weaning till the final out weight of the postweaning gain test) and MMWT_WW, calculated similarly. Overall average estimated DMI was highly correlated to the measurements derived over shorter periods, with 10 d being the least correlated and 60 d being the most correlated. The ADG_Calc (calculated using 2-d consecutive start and finish weight/DOF) and ADG_WW were highly correlated in Charolais. The ADG_Regress and ADG_Calc were highly correlated, and ADG_Regress and ADG_WW were moderately correlated in Red Angus. The control measures of RFI were highly correlated with the RFI_WW in Charolais and Red Angus. The outcomes of including abbreviated period DMI in the model with the weaning weight gain measurements showed that the model using 10 d of intake (RFI WW_10) was the least correlated with the control measures. The model with 60 d of intake had

  2. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Eye Symptoms Causes of Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué ... Your Eyelid Nov 29, 2017 New Dry Eye Treatment is a Tear-Jerker Jul 21, 2017 Three ...

  3. Drying of building lumber

    Energy Technology Data Exchange (ETDEWEB)

    Washimi, Hiroshi

    1988-08-20

    Dried lumber is classified into air dried and kiln-dried lumber. The water content of kiln-dried lumber is specified by the Japan Agricultural Standards. However, since building lumber varies in such factors as the location where it was growing, species and shape, the standards, though relaxed, are not being observed. In fact, lumbered products which are not ''Kiln-dried'' frequently bear ''kiln-dried lumber'' marks. In an attempt to correct the situation, the Forestry Agency has set up voluntary standards, but problems still remain. The conventional drying method consists of first subjecting the lumber to optimum drying, then letting bending and deformations to freely and fully appear, and follow this with corrective sawing to produce planks straight from end to end. Compared with air dried lumber in terms of moisture content, kiln-dried lumber remains much with same with minimal shrinkage and expansion. For oil-containing resin, such normal treatments as drying by heating, steaming and boiling seem to be quite effective. Kiln drying, which is becoming more and more important with changes in the circulation system, consists of the steaming-drying-heating method and the dehumidizing type drying method. The major factor which determines the drying cost is the number of days required for drying, which depends largely on the kind of lumber and moisture content. The Forestry Angency is promoting production of defoiled lumber. (2 figs, 2 tables)

  4. Distribution of major elements (Na, K, Ca, Mg in the various anatomical parts of Fadama crops in Ekiti State, Nigeria

    Directory of Open Access Journals (Sweden)

    E.I. Adeyeye

    2005-12-01

    Full Text Available Levels of sodium, potassium, calcium and magnesium were determined in plant organs (bud, flowers, fruit, seed, leaves, stems, roots, cobs, styles, shaft, grains and efflorescences of three Fadama farms located in Ifaki-Ekiti, Ado-Ekiti and Ikere-Ekiti of Ekiti State, Nigeria. The highest levels of Mg, K, Na and Ca were obtained in the bud of Hibiscus esculentus with respective values (ppm dry weight, ppm DW of 4397, 2983, 3928 and 1622; this was closely followed by their levels in Lycopersicon esculentum root: Mg (2734, K (1079, Na (2111 and Ca (678. The levels of all the elements were highly varied in the anatomical parts of each plant and between the various plants. The index of bioaccumulation (ratio in plants/soil was recorded for all the elements with all values falling within 1-101 showing that the degree of accumulation was intensive. The overall levels of the elements were Mg > Na > K > Ca.

  5. Effects of the usage of dried brewing yeast in the diets on the performance, egg traits and blood parameters in quails.

    Science.gov (United States)

    Yalçın, S; Erol, H; Ozsoy, B; Onbaşılar, I; Yalçın, S

    2008-12-01

    This experiment was carried out to determine the effects of the usage of dried brewing yeast in quail diets on laying performance, egg traits and blood parameters. A total of 240 Japanese quails (Coturnix coturnix japonica) aged 10 weeks were randomly allocated into one control group and three treatment groups. Each group was divided into five replicates as subgroups, comprising 12 quails each. Dried brewing yeast (Saccharomyces cerevisiae) was used at the levels of 1.5%, 3.0% and 4.5% in the diets of the first, second and third treatment groups, respectively. Soyabean meal was replaced with dried brewing yeast. The diets were formulated to be isocaloric and isonitrogenous. The experimental period lasted 18 weeks. Dietary treatments did not significantly affect body weight, daily feed intake, daily protein intake, egg production, egg weight, feed efficiency, mortality, egg shell thickness, egg albumen index, egg yolk index, egg Haugh unit, the percentages of egg shell, albumen and yolk, excreta moisture and small intestinal pH. Inclusion of 3% and 4.5% dried brewing yeast in diets reduced egg yolk cholesterol concentration as mg per yolk and mg per g yolk (P brewing yeast was significantly lower (P brewing yeast resulted in significant increases (P brewing yeast. It is concluded that dried brewing yeast can be used up to 4.5% in the diets of laying quails without adverse effects on the measured parameters.

  6. Determination of pistachio drying behaviour and conditions in a solar drying system

    Energy Technology Data Exchange (ETDEWEB)

    Midilli, Adnan [Karadeniz Technical Univ., Mechanical Engineering Dept., Trabzon (Turkey)

    2001-07-01

    The main object of this study is to determine the drying behaviour and conditions of shelled and unshelled pistachio samples using both solar assisted and open sun drying. For each drying experiment, 100 g each of unshelled and shelled pistachio were used. The least-squares method was applied to find the drying curve equation of pistachio. During the experiments, shelf temperatures, weight loss of pistachio, moisture content of air, and distribution of solar radiation were measured; and presented depending on the drying time. Also, the mass shrinkage ratios of shelled and unshelled pistachio samples were determined, and the experimental uncertainty ratio was calculated as 15-16.5 per cent based on the experimental results. It was deduced that the shelled and unshelled pistachio samples in the solar assisted forced convection dryer were perfectly dried at temperatures of 50{+-}10degC in the time period of 6 h. Whereas, the samples in the open sun drying were not sufficiently dried at temperatures of 28{+-}4degC in the same time period. Hence, it is suggested that the pistachio samples with approximately 29.0 per cent of moisture are dried in the solar assisted convection dryer at 50{+-}10degC of temperature in the time period of approximately 6 h in order to protect from the negative climatic and environmental effects. However, it is not desirable to dry the pistachio samples in the open sun because of greater drying time, dirt, dust and harmful insects. (Author)

  7. Recent advances in drying and dehydration of fruits and vegetables: a review.

    Science.gov (United States)

    Sagar, V R; Suresh Kumar, P

    2010-01-01

    Fruits and vegetables are dried to enhance storage stability, minimize packaging requirement and reduce transport weight. Preservation of fruits and vegetables through drying based on sun and solar drying techniques which cause poor quality and product contamination. Energy consumption and quality of dried products are critical parameters in the selection of drying process. An optimum drying system for the preparation of quality dehydrated products is cost effective as it shortens the drying time and cause minimum damage to the product. To reduce the energy utilization and operational cost new dimensions came up in drying techniques. Among the technologies osmotic dehydration, vacuum drying, freeze drying, superheated steam drying, heat pump drying and spray drying have great scope for the production of quality dried products and powders.

  8. Nuttall Oak Volume and Weight Tables

    Science.gov (United States)

    Bryce E. Schlaegel; Regan B. Willson

    1983-01-01

    Volume and weight tables were constructed from a 62-tree sample of Nuttall oak (Quercus nuttallii Palmer) taken in the Mississippi Delta. The tables present volume, green weight, and dry weight of bole wood, bole wood plus bark, and total tree above a one-foot stump as predicted from the nonlinear model Y = 0Db

  9. Antibacterial biodegradable Mg-Ag alloys

    Directory of Open Access Journals (Sweden)

    D Tie

    2013-06-01

    Full Text Available The use of magnesium alloys as degradable metals for biomedical applications is a topic of ongoing research and the demand for multifunctional materials is increasing. Hence, binary Mg-Ag alloys were designed as implant materials to combine the favourable properties of magnesium with the well-known antibacterial property of silver. In this study, three Mg-Ag alloys, Mg2Ag, Mg4Ag and Mg6Ag that contain 1.87 %, 3.82 % and 6.00 % silver by weight, respectively, were cast and processed with solution (T4 and aging (T6 heat treatment.The metallurgical analysis and phase identification showed that all alloys contained Mg4Ag as the dominant β phase. After heat treatment, the mechanical properties of all Mg-Ag alloys were significantly improved and the corrosion rate was also significantly reduced, due to presence of silver. Mg(OH2 and MgO present the main magnesium corrosion products, while AgCl was found as the corresponding primary silver corrosion product. Immersion tests, under cell culture conditions, demonstrated that the silver content did not significantly shift the pH and magnesium ion release. In vitro tests, with both primary osteoblasts and cell lines (MG63, RAW 264.7, revealed that Mg-Ag alloys show negligible cytotoxicity and sound cytocompatibility. Antibacterial assays, performed in a dynamic bioreactor system, proved that the alloys reduce the viability of two common pathogenic bacteria, Staphylococcus aureus (DSMZ 20231 and Staphylococcus epidermidis (DSMZ 3269, and the results showed that the killing rate of the alloys against tested bacteria exceeded 90%. In summary, biodegradable Mg-Ag alloys are cytocompatible materials with adjustable mechanical and corrosion properties and show promising antibacterial activity, which indicates their potential as antibacterial biodegradable implant materials.

  10. Intra-individual comparison of different contrast media concentrations (300 mg, 370 mg and 400 mg iodine) in MDCT

    Energy Technology Data Exchange (ETDEWEB)

    Behrendt, Florian F.; Keil, Sebastian; Plumhans, Cedric; Guenther, Rolf W. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); Pietsch, Hubertus; Jost, Gregor; Sieber, Martin A.; Seidensticker, Peter [Bayer Schering Pharma AG, Berlin (Germany); Mahnken, Andreas H. [RWTH Aachen University, Department of Diagnostic Radiology, University Hospital, Aachen (Germany); RWTH Aachen University, Applied Medical Engineering, Helmholtz-Institute for Biomedical Engineering, Aachen (Germany)

    2010-07-15

    To compare intra-individual contrast enhancement in multi-detector-row computed tomography (MDCT) using contrast media (CM) containing 300, 370 and 400 mg iodine per ml (mgI/ml). Six pigs underwent repeated chest MDCT using three different CM (iopromide 300, iopromide 370, iomeprol 400). An identical iodine delivery (IDR) rate of 1.5 gI/s and a constant total iodine dose of 300 mg/kg body weight were used. Dynamic CT were acquired at the level of the pulmonary artery, and the ascending and descending aorta. After the time enhancement curves were computed, the pulmonary and aortic peak enhancement, time to peak and plateau time above 300 HU were calculated. Intra-individual peak contrast enhancement was significantly higher for the 300 mgI/ml contrast medium compared with the 370 and 400 mgI/ml media: pulmonary trunk 595 HU vs 516 HU (p = 0.0093) vs 472HU (p = 0.0005), and aorta 505 HU vs 454 HU (p = 0.0008) vs 439 HU (p = 0.0001), respectively. Comparison of time to peaks showed no significant difference. Plateau times were significantly longer for the 300 mgI/ml than for the 370 and 400 mgI/ml CM at all anatomical sites. Given normalised IDR and total iodine burden, the use of CM with a standard concentration with 300 mg iodine/ml provides improved contrast enhancement compared with highly concentrated CM in the chest. (orig.)

  11. Weighted Clustering

    DEFF Research Database (Denmark)

    Ackerman, Margareta; Ben-David, Shai; Branzei, Simina

    2012-01-01

    We investigate a natural generalization of the classical clustering problem, considering clustering tasks in which different instances may have different weights.We conduct the first extensive theoretical analysis on the influence of weighted data on standard clustering algorithms in both...... the partitional and hierarchical settings, characterizing the conditions under which algorithms react to weights. Extending a recent framework for clustering algorithm selection, we propose intuitive properties that would allow users to choose between clustering algorithms in the weighted setting and classify...

  12. Dry Mouth (Xerostomia)

    Science.gov (United States)

    ... Finding Dental Care Home Health Info Health Topics Dry Mouth Saliva, or spit, is made by the salivary ... help keep teeth strong and fight tooth decay. Dry mouth, also called xerostomia (ZEER-oh-STOH-mee-ah), ...

  13. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Dry Eye Symptoms Related Ask an Ophthalmologist Answers Can a six-month dissolvable punctal plug be removed ... my eyes dry after LASIK? Jun 19, 2016 Can I be tested whether I close my eyes ...

  14. The influence of lysozyme on mannitol polymorphism in freeze-dried and spray-dried formulations depends on the selection of the drying process.

    Science.gov (United States)

    Grohganz, Holger; Lee, Yan-Ying; Rantanen, Jukka; Yang, Mingshi

    2013-04-15

    Freeze-drying and spray-drying are often applied drying techniques for biopharmaceutical formulations. The formation of different solid forms upon drying is often dependent on the complex interplay between excipient selection and process parameters. The purpose of this study was to investigate the influence of the chosen drying method on the solid state form. Mannitol-lysozyme solutions of 20mg/mL, with the amount of lysozyme varying between 2.5% and 50% (w/w) of total solid content, were freeze-dried and spray-dried, respectively. The resulting solid state of mannitol was analysed by near-infrared spectroscopy in combination with multivariate analysis and further, results were verified with X-ray powder diffraction. It was seen that the prevalence of the mannitol polymorphic form shifted from β-mannitol to δ-mannitol with increasing protein concentration in freeze-dried formulations. In spray-dried formulations an increase in protein concentration resulted in a shift from β-mannitol to α-mannitol. An increase in final drying temperature of the freeze-drying process towards the temperature of the spray-drying process did not lead to significant changes. It can thus be concluded that it is the drying process in itself, rather than the temperature, that leads to the observed solid state changes. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. The amount of food ingested in a single meal by rainbow trout offered chopped herring, dry and wet diets

    Science.gov (United States)

    Ruohonen; Grove; McIlroy

    1997-07-01

    Two-year-old 1·5-kg rainbow trout were held in cages and conditioned by feeding either on low-fat chopped herring (H trout) or dry pellets (P trout) for 15 weeks. Their satiation amounts were then determined under standard conditions. On a wet weight basis H trout ate 2·5-3·5 times more food than P trout; this was sufficient to compensate for the high water content of herring and thereby maintain the dry matter intake. When P trout were offered herring (PH trout) they consumed more food than when offered dry pellets but not as much as H trout. Stomach capacity restricted the intake and their dry matter intake was reduced by c. 40%. When H trout were offered dry pellets (HP trout) they adjusted their intake immediately close to the level of P trout although their larger stomachs could have accommodated more than twice this volume of dry food. The return of appetite after a satiation meal was almost linear with time. Appetite increased at c. 556 mg g-1 body weight h-1 for H trout and at 142 mg g-1 bw h-1 for P trout. The return of appetite in PH trout was significantly slower (c. 370 mg g-1 bw h-1) than in H trout; the previous dietary history of the PH trout limited their capacity to process larger volumes of wet food in a single meal. Fish offered dry diet (P and HP trout) had similar rates of appetite return despite their previous feeding history suggesting that the property of the dry feed itself might limit meal size. The total gastric emptying time of diets of similar dry matter content (with and without large amounts of water) was similar, but the delay time before gastric emptying starts tended to be longer for dry diets. Dry pellets appear to impose a demand for water that prolongs the gastric delay. This water demand is met partly by drinking since the trout fed on dry pellets drank significantly more (436±189 mg kg-1 h-1) than unfed and herring-fed trout which drank little or not at all (65±113 and 70±66 mg kg-1 h-1 respectively). Dietary water

  16. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Eye Health A-Z Symptoms Glasses & Contacts Tips & Prevention News Ask an Ophthalmologist Patient Stories Español Eye ... Eye Symptoms Causes of Dry Eye Dry Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué ...

  17. Drying process of fermented inulin fiber concentrate by Bifidobacterium bifidum as a dietary fiber source for cholesterol binder

    Science.gov (United States)

    Susilowati, Agustine; Aspiyanto, Ghozali, Muhammad

    2017-11-01

    Fermentation on inulin hydrolysate as fructooligosaccharides (FOS) by Bifidobacterium bifidum as a result of hydrolysis by inulase enzyme of Scopulariopsis sp.-CBS1 fungi has been performed to bind cholesterol. Their applications on preparation of fermented pour beverages was conducted via a series of concentration process using dead-end Stirred Ultrafiltration Cell (SUFC) mode at stirrer rotation of 400 rpm, room temperature and pressure of 40 psia for 0 minute (pre-concentration process) as concentrate (A) and 45 minutes as concentrate (B), and drying process using vacuum dryer at 30 °C and 22 cm Hg for 0, 8, 16, 24, 32, 40 and 48 hours. Based on optimization of Total Dietary Fiber (TDF), the best time of drying process was achieved for 40 hours. Long time of drying process would increase TDF and total solids, decreased total acids, and fluctuated dissolved protein and Cholesterol Binding Capacity (CBC). At the optimum condition of drying process was get fermented inulin fiber powder from concentration processes using both UF as pre process (0 minute) as concentrate (A) and UF for 45 minutes as concentrate (B) with compositions of total solids of 92.31 % and 93.67 %, TDF of 59.07 % (dry weight) and 69.28 %, total acids of 7.03 % and 7.5 %, dissolved protein of 3.95 mg/mL and 3.05 mg/mL, and CBC pH 2 15.71 mg/g and 16.8 mg/g, respectively. Concentration process through dead-end SUFC mode gave distribution of particles with better smoothness level than without through dead-end SUFC mode.

  18. Drying-induced physico-chemical changes in cranberry products.

    Science.gov (United States)

    Michalska, Anna; Wojdyło, Aneta; Honke, Joanna; Ciska, Ewa; Andlauer, Wilfried

    2018-02-01

    Sugar-free cranberry juice (XAD) and juice with 15% of maltodextrin were dried by freeze-, vacuum and spray drying methods. Total phenolics (589-6435mg/kg dry matter) including 5 flavonols, 3 phenolic acids, 2 procyanidins and 5 anthocyanins were stronger affected by juice formulation than by drying methods. Spray drying of juice, regardless of its formulation, was competitive to freeze drying in terms of polyphenols' retention. Increase in temperature up to 100°C during vacuum drying of XAD extracts resulted in degradation of polyphenolics (down to 4%), except chlorogenic acid. Its content increased with rise in temperature and accelerated hydroxymethylfurfural formation. The stronger the impact of drying, the more chlorogenic acid is present in cranberry products. In all powders analysed, formation of furoylmethyl amino acids was noted. Antioxidant capacity of cranberry products was influenced by juice formulation and was linked to content of polyphenols. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Dry and Semi-Dry Tropical Cyclones

    Science.gov (United States)

    Cronin, T.; Chavas, D. R.

    2017-12-01

    Our understanding of dynamics in our real moist atmosphere is strongly informed by idealized dry models. It is widely believed that tropical cyclones (TCs) are an intrinsically moist phenomenon - relying fundamentally on evaporation and latent heat release - yet recent numerical modeling work has found formation of dry axisymmetric tropical cyclones from a state of dry radiative-convective equilibrium. What can such "dry hurricanes" teach us about intensity, structure, and size of real moist tropical cyclones in nature? Are dry TCs even stable in 3D? What about surfaces that are nearly dry but have some latent heat flux - can they also support TCs? To address these questions, we use the SAM cloud-system resolving model to simulate radiative-convective equilibrium on a rapidly rotating f-plane, subject to constant tropospheric radiative cooling. We use a homogeneous surface with fixed temperature and with surface saturation vapor pressure scaled by a factor 0-1 relative to that over pure water - allowing for continuous variation between moist and dry limits. We also explore cases with surface enthalpy fluxes that are uniform in space and time, where partitioning between latent and sensible heat fluxes is specified directly. We find that a completely moist surface yields a TC-world where multiple vortices form spontaneously and persist for tens of days. A completely dry surface can also yield a parallel dry TC-world with many vortices that are even more stable and persistent. Spontaneous cyclogenesis, however, is impeded for a range of low to intermediate surface wetness values, and by the combination of large rotation rates and a dry surface. We discuss whether these constraints on spontaneous cyclogenesis might arise from: 1) rain evaporation in the subcloud layer limiting the range of viable surface wetness values, and 2) a natural convective Rossby number limiting the range of viable rotation rates. Finally, we discuss simulations with uniform surface enthalpy

  20. Dry vacuum pumps

    International Nuclear Information System (INIS)

    Sibuet, R

    2008-01-01

    For decades and for ultimate pressure below 1 mbar, oil-sealed Rotary Vane Pumps have been the most popular solution for a wide range of vacuum applications. In the late 80ies, Semiconductor Industry has initiated the development of the first dry roughing pumps. Today SC applications are only using dry pumps and dry pumping packages. Since that time, pumps manufacturers have developed dry vacuum pumps technologies in order to make them attractive for other applications. The trend to replace lubricated pumps by dry pumps is now spreading over many other market segments. For the Semiconductor Industry, it has been quite easy to understand the benefits of dry pumps, in terms of Cost of Ownership, process contamination and up-time. In this paper, Technology of Dry pumps, its application in R and D/industries, merits over conventional pumps and future growth scope will be discussed

  1. The effects of Echinacea purpurea dried extract on humoral immune ...

    African Journals Online (AJOL)

    edoja

    however, some of the poultry farms are being encountered with this disease because the available vaccines ... For six weeks, various doses of dry extract (17, 21, 25, 29 mg/kg) ... producing institute, were used as eye drop and subcutaneous.

  2. Status Ca, Mg dan Zn pada Kambing Peranakan Etawah Muda yang Diberi Ransum Bentuk Mash dengan Pakan Sumber Serat Berbeda

    Directory of Open Access Journals (Sweden)

    T. Toharmat

    2007-08-01

    Full Text Available Fibrous agricultural by-products are the component of most rations for ruminant raised intensively. Slow rate and low digestibility of the fibrous feed may limit mineral bioavailability. Present experiment aimed to clarify the influence of fibrous feed component in ration on the status of Ca, Mg and Zn in growing goats. Twenty of female Etawah-grade goats weighing of 13.5±2.14 kg were grouped and allocated into five treatments in a randomized block design. Rations composed of 50% fibrous feed and 50% concentrate. The fibrous feed component as treatments were: RG = napier grass, JP = rice straw, KC = cacao pod, JK = mixed rice straw and coffee husk, and CP = mixed rice straw, napier grass, coffee husk and cacao pod. Rations were offered at 3% of live weight. The result showed that fibrous feed influenced Ca, Mg, and Zn intake, Ca and Mg absorption, and Ca, Mg and Zn plasma of growing goats. Intake, absorption and plasma Ca, Mg, and Zn had positive correlation with dry mater intake. Absorption of Ca and Zn had positive correlations with crude fiber digestibility. Supplementation of Ca, Mg and Zn was necessary when the fibrous feed was included at the level of 50% in the ration of growing goats, but the supplement level varied according to the type of the fibrous feed.

  3. Quality properties of fruits as affected by drying operation.

    Science.gov (United States)

    Omolola, Adewale O; Jideani, Afam I O; Kapila, Patrick F

    2017-01-02

    The increasing consumption of dried fruits requires further attention on the quality parameters. Drying has become necessary because most fruits are highly perishable owing to their high moisture content and the need to make them available all year round and at locations where they are not produced. In addition to preservation, the reduced weight and bulk of dehydrated products decreases packaging, handling and transportation costs. Quality changes associated with drying of fruit products include physical, sensory, nutritional, and microbiological. Drying gives rise to low or moderate glycemic index (GI) products with high calorie, vitamin and mineral contents. This review examines the nutritional benefits of dried fruits, protective compounds present in dried fruits, GI, overview of some fruit drying methods and effects of drying operations on the quality properties such as shrinkage, porosity, texture, color, rehydration, effective moisture diffusivity, nutritional, sensory, microbiological and shelf stability of fruits.

  4. Antibacterial effect of citrus press-cakes dried by high speed and far-infrared radiation drying methods

    Science.gov (United States)

    Samarakoon, Kalpa; Senevirathne, Mahinda; Lee, Won-Woo; Kim, Young-Tae; Kim, Jae-Il; Oh, Myung-Cheol

    2012-01-01

    In this study, the antibacterial effect was evaluated to determine the benefits of high speed drying (HSD) and far-infrared radiation drying (FIR) compared to the freeze drying (FD) method. Citrus press-cakes (CPCs) are released as a by-product in the citrus processing industry. Previous studies have shown that the HSD and FIR drying methods are much more economical for drying time and mass drying than those of FD, even though FD is the most qualified drying method. The disk diffusion assay was conducted, and the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) were determined with methanol extracts of the dried CPCs against 11 fish and five food-related pathogenic bacteria. The disk diffusion results indicated that the CPCs dried by HSD, FIR, and FD prevented growth of all tested bacteria almost identically. The MIC and MBC results showed a range from 0.5-8.0 mg/mL and 1.0-16.0 mg/mL respectively. Scanning electron microscopy indicated that the extracts changed the morphology of the bacteria cell wall, leading to destruction. These results suggest that CPCs dried by HSD and FIR showed strong antibacterial activity against pathogenic bacteria and are more useful drying methods than that of the classic FD method in CPCs utilization. PMID:22808341

  5. Single droplet drying step characterization in microsphere preparation.

    Science.gov (United States)

    Al Zaitone, Belal; Lamprecht, Alf

    2013-05-01

    Spray drying processes are difficult to characterize since process parameters are not directly accessible. Acoustic levitation was used to investigate microencapsulation by spray drying on one single droplet facilitating the analyses of droplet behavior upon drying. Process parameters were simulated on a poly(lactide-co-glycolide)/ethyl acetate combination for microencapsulation. The results allowed quantifying the influence of process parameters such as temperature (0-40°C), polymer concentration (5-400 mg/ml), and droplet size (0.5-1.37 μl) on the drying time and drying kinetics as well as the particle morphology. The drying of polymer solutions at temperature of 21°C and concentration of 5 mg/ml, shows that the dimensionless particle diameter (Dp/D0) approaches 0.25 and the particle needs 350 s to dry. At 400 mg/ml, Dp/D0=0.8 and the drying time increases to one order of magnitude and a hollow particle is formed. The study demonstrates the benefit of using the acoustic levitator as a lab scale method to characterize and study the microparticle formation. This method can be considered as a helpful tool to mimic the full scale spray drying process by providing identical operational parameters such as air velocity, temperature, and variable droplet sizes. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. Drying and energy technologies

    CERN Document Server

    Lima, A

    2016-01-01

    This book provides a comprehensive overview of essential topics related to conventional and advanced drying and energy technologies, especially motivated by increased industry and academic interest. The main topics discussed are: theory and applications of drying, emerging topics in drying technology, innovations and trends in drying, thermo-hydro-chemical-mechanical behaviors of porous materials in drying, and drying equipment and energy. Since the topics covered are inter- and multi-disciplinary, the book offers an excellent source of information for engineers, energy specialists, scientists, researchers, graduate students, and leaders of industrial companies. This book is divided into several chapters focusing on the engineering, science and technology applied in essential industrial processes used for raw materials and products.

  7. Chemical and physical parameters of dried salted pork meat

    Directory of Open Access Journals (Sweden)

    Petronela Cviková

    2016-07-01

    Full Text Available The aim of the present study was analysed and evaluated chemical and physical parameters of dried salted pork neck and ham. Dried salted meat is one of the main meat products typically produced with a variety of flavors and textures. Neck (14 samples and ham (14 samples was salted by nitrite salt mixture during 1week. The nitrite salt mixture for salting process (dry salting was used. This salt mixture contains: salt, dextrose, maltodextrin, flavourings, stabilizer E316, taste enhancer E621, nitrite mixture. The meat samples were dried at 4 °C and relative humudity 85% after 1 week salting. The weight of each sample was approximately 1 kg. After salting were vacuum-packed and analysed after 1 week. The traditional dry-cured meat such as dry-cured ham and neck obtained after 12 - 24 months of ripening under controlled conditions. The average protein content was significantly (p <0.001 lower in dried pork neck in comparison with dried salted pork ham. The average intramuscular fat was significantly (p <0.001 lower in dried pork ham in comparison with dried salted pork neck. The average moisture was significantly lower (p ≤0.05 in dried salted ham in comparison with dried pork neck. The average pH value was 5.50 in dried salted pork ham and 5.75 in dried salted pork neck. The content of arginine, phenylalanine, isoleucine, leucine and threonine in dried salted ham was significantly lower (p <0.001 in comparison with dried salted pork neck. The proportion of analysed amino acids from total proteins was 56.31% in pork salted dried ham and 56.50% in pork salted dried neck.  Normal 0 21 false false false EN-GB X-NONE X-NONE Normal 0 21 false false false SK X-NONE X-NONE

  8. Decontamination of polypropylene fabrics by dry cleaning

    International Nuclear Information System (INIS)

    Severa, J.; Knajfl, J.

    1983-01-01

    Polypropylene fabrics can efficiently be decontaminated by dry cleaning in benzine or perchloroethylene, this also in case the fabric was greased in addition to radioactive contamination. For heavily soiled fabric, it is advantageous to first dry clean it and then wash it. The positive effect was confirmed of intensifiers on the cleaning process, especially of benzine soap. In practice, its concentration should be selected within 1 and 10 g.dm - 3 . Decontamination by dry cleaning and subsequent washing is advantageous in that that the resulting activity of waste water from the laundry is low. Radioactive wastes from the dry cleaning process have a low weight and can be handled as solid waste. (M.D.)

  9. Ambient Dried Aerogels

    Science.gov (United States)

    Jones, Steven M.; Paik, Jong-Ah

    2013-01-01

    A method has been developed for creating aerogel using normal pressure and ambient temperatures. All spacecraft, satellites, and landers require the use of thermal insulation due to the extreme environments encountered in space and on extraterrestrial bodies. Ambient dried aerogels introduce the possibility of using aerogel as thermal insulation in a wide variety of instances where supercritically dried aerogels cannot be used. More specifically, thermoelectric devices can use ambient dried aerogel, where the advantages are in situ production using the cast-in ability of an aerogel. Previously, aerogels required supercritical conditions (high temperature and high pressure) to be dried. Ambient dried aerogels can be dried at room temperature and pressure. This allows many materials, such as plastics and certain metal alloys that cannot survive supercritical conditions, to be directly immersed in liquid aerogel precursor and then encapsulated in the final, dried aerogel. Additionally, the metalized Mylar films that could not survive the previous methods of making aerogels can survive the ambient drying technique, thus making multilayer insulation (MLI) materials possible. This results in lighter insulation material as well. Because this innovation does not require high-temperature or high-pressure drying, ambient dried aerogels are much less expensive to produce. The equipment needed to conduct supercritical drying costs many tens of thousands of dollars, and has associated running expenses for power, pressurized gasses, and maintenance. The ambient drying process also expands the size of the pieces of aerogel that can be made because a high-temperature, high-pressure system typically has internal dimensions of up to 30 cm in diameter and 60 cm in height. In the case of this innovation, the only limitation on the size of the aerogels produced would be in the ability of the solvent in the wet gel to escape from the gel network.

  10. Accelerated dry curing of hams.

    Science.gov (United States)

    Marriott, N G; Kelly, R F; Shaffer, C K; Graham, P P; Boling, J W

    1985-01-01

    Uncured pork legs from the right side of 18 carcasses were treated with a Ross Tenderizer and the left side were controls. All 36 samples were dry-cured for 40, 56 or 70 days and evaluated for appearance traits, cure penetration characteristics, microbial load, Kramer Shear force and taste attributes. The tenderization treatment had no effect (P > 0·05) on visual color or cure penetration rate, weight loss before curing, percentage moisture, nitrate level, nitrite level, total plate count, anaerobic counts, psychrotrophic counts, objective and subjective tenderness measurements or juiciness. However, the higher values of salt suggested a possible acceleration of the dry cure penetration process among the tenderized samples. Cure time had no effect (P > 0·05) on percentage moisture, percentage salt, nitrate content, nitrite content, shear force and juiciness. Results suggest a limited effect of the mechanical tenderization process on certain traits related to dry curing and that total process time should be at least 70 days if color stability during cooking is desired. Copyright © 1985. Published by Elsevier Ltd.

  11. Dry etching for microelectronics

    CERN Document Server

    Powell, RA

    1984-01-01

    This volume collects together for the first time a series of in-depth, critical reviews of important topics in dry etching, such as dry processing of III-V compound semiconductors, dry etching of refractory metal silicides and dry etching aluminium and aluminium alloys. This topical format provides the reader with more specialised information and references than found in a general review article. In addition, it presents a broad perspective which would otherwise have to be gained by reading a large number of individual research papers. An additional important and unique feature of this book

  12. Inflammation in dry eye.

    Science.gov (United States)

    Stern, Michael E; Pflugfelder, Stephen C

    2004-04-01

    Dry eye is a condition of altered tear composition that results from a diseased or dysfunctional lacrimal functional unit. Evidence suggests that inflammation causes structural alterations and/or functional paralysis of the tear-secreting glands. Changes in tear composition resulting from lacrimal dysfunction, increased evaporation and/or poor clearance have pro-inflammatory effects on the ocular surface. This inflammation is responsible in part for the irritation symptoms, ocular surface epithelial disease, and altered corneal epithelial barrier function in dry eye. Anti-inflammatory therapies for dry eye target one or more of the inflammatory mediators/pathways that have been identified in dry eye.

  13. Drying hardwood lumber

    Energy Technology Data Exchange (ETDEWEB)

    Chow, A T

    1988-11-14

    Dried lumber is a high-value-added product, especially when it is of high quality. Lumber damaged during the drying operation can represent substantial lost revenue. It has been demonstrated that dehumidification kilns can improve lumber quality, and reduce energy consumption over conventional drying methods. A summary of the literature on drying hardwood lumber, particularly using heat pump dehumidification, has been prepared to allow the information to be readily accessible to Ontario Hydro personnel who work with customers in the lumber industry. For that purpose, this summary has been prepared from the perspective of the customer, a dry kiln operator. Included are brief descriptions of drying schedules, precautions needed to minimize drying defects in the lumber, and rules-of-thumb for selecting and estimating the capital cost of the drying equipment. A selection of drying schedules and moisture contents of green lumber, a glossary of lumber defects and brief descriptions of the possible preventive measures are also included. 10 refs., 8 figs., 4 tabs.

  14. Physical properties of sunflower grains after drying

    Directory of Open Access Journals (Sweden)

    Paulo Carteri Coradi

    2015-12-01

    Full Text Available The knowledge of the physical properties of the grains is important for the optimization of post-harvest operations. This study aimed to evaluate the effects of convective drying with different air temperatures (45, 55, 65 and 75 °C the physical properties of sunflower seeds. The drying sunflower grains was performed in convection oven with forced air. In natural conditions, samples of 5 kg of pellets were used for each repetition drying. During the drying process, the grains samples were weighed periodically until they reach 10% (wet basis, w.b., then were subjected to evaluations of physical properties. According to the results it was observed that the porosity, apparent density, thousand kernel weight to the drag coefficient, roundness, sphericity and width of sunflower seed did not change with increasing temperature drying air. It was concluded that the drying air temperatures of 45 °C and 55 retained the initial physical characteristics of sunflower seeds. The temperature of the drying air of 75 °C had greater influence on changes in volumetric shrinkage of the grains.

  15. Spray drying of bead resins: feasibility tests

    International Nuclear Information System (INIS)

    Gay, R.L.; Grantham, L.F.; Jones, L.J.

    1984-01-01

    Rockwell International has developed a volume reduction system for low-level reactor wastes based on drying the wastes in a heated-air spray dryer. The drying of slurries of sodium sulfate, boric acid, and powdered ion exchange resins was demonstrated in previous tests. The drying of bead ion exchange resins can be especially difficult due to the relatively large size of bead resins (about 500 to 800 microns) and their natural affinity for water. This water becomes part of the pore structure of the resins and normally comprises 50 t 60 wt % of the resin weight. A 76-cm-diameter spray dryer was used for feasibility tests of spray drying of cation and anion bead resins. These resins were fed to the dryer in the as-received form (similar to dewatered resins) and as slurries. A dry, free-flowing product was produced in all the tests. The volume of the spray-dried product was one-half to one-third the volume of the as-received material. An economic analysis was made of the potential cost savings that can be achieved using the Rockwel spray dryer system. In-plant costs, transportation costs, and burial costs of spray-dried resins were compared to similar costs for disposal of dewatered resins. A typical utility producing 170 m 3 (6,000 ft 3 ) per year of dewatered resins can save $600,000 to $700,000 per year using this volume reduction system

  16. Experimental Study of Paddy Grain Drying in Continuous Recirculation System Pneumatic Conveyor

    Directory of Open Access Journals (Sweden)

    Prasetyo Totok

    2018-01-01

    Full Text Available Nowadays, paddy drying using conventional method is irrelevant to used. The increasing need of grain each year is one of the main factor that pushes scientist to invent new methods of drying paddy grain. The old method is unusefull since it takes up space, needed the sun as the drying media which causes a long drying time. One of the alternative of drying paddy grain is by using mechanic dryer. By using this dryer type, the process of drying takes faster comparing to the old method and the distribution of grain is supplied continuously. The dryer which uses pneumatic conveyor can be one of the solution due to its less energy consumption, a better drying result, and high drying capacity. The variable used to identify drying performance is temperature and loading weight. From the experiment, it is resulted that the best temperature for drying paddy grain is 60°C with the weight loading of 150 gram.

  17. Drying Characteristics and Water-soluble Polysaccharides Evaluation of Kidney Shape Ganoderma lucidum Drying in Air Circulation System

    Science.gov (United States)

    Prasetyo, D. J.; Jatmiko, T. H.; Poeloengasih, C. D.; Kismurtono, M.

    2017-12-01

    In this project, drying kinetic of kidney shape Ganoderma lucidum fruiting body in air circulation system was studied. The drying experiments were conducted at 40, 50 and 60°C with air flow rate of 1.3 ms-1. Samples were weighted periodically until no change in sample weight was recorded, and then the samples were analyzed for its moisture content. Four different thin-layer mathematical models (Newton, Page, Two-term, Midilli) were used and compare to evaluate the drying curves of kidney shape G. lucidum. The water-soluble polysaccharides were evaluated in order to find the best drying temperature condition. The results indicates that Midilli model was the fittest model to describe the characteristic of kidney shape G. lucidum in the air circulation drying system and temperature of 50°C was the best drying condition to get highest value of water-soluble polysaccharides.

  18. Weight Loss

    Science.gov (United States)

    ... Rights Employment Discrimination Health Care Professionals Law Enforcement Driver's License For Lawyers Food & Fitness Home Food MyFoodAdvisor ... Fit Types of Activity Weight Loss Assess Your Lifestyle Getting Started Food Choices In My Community Home ...

  19. Effect of different seawater Mg

    NARCIS (Netherlands)

    Mewes, A.; Langer, G.; de Nooijer, L.J.; Bijma, J.; Reichart, G.J.

    2014-01-01

    Magnesium, incorporated in foraminiferal calcite (Mg/CaCC), is used intensively to reconstruct past seawater temperatures but, in addition to temperature, the Mg/CaCC of foraminiferal tests also depends on the ratio of Mg and Ca in seawater (Mg/CaSW). The physiological mechanisms responsible for

  20. Acute and subchronic toxicity study of the water extract from dried fruits of Piper nigrum L. in rats

    Directory of Open Access Journals (Sweden)

    Kanjana Jaijoy

    2007-03-01

    Full Text Available The study was carried out to evaluate acute and subchronic toxicities of the water extract from the dried fruits of Piper nigrum L. A single oral administration of the extract at a dose of 5,000 mg/kg body weight (5 male, 5 female did not produce signs of toxicity, behavioral changes, mortality, changes on gross appearance or histopathological changes of internal organs. The subchronic toxicity was determined by oral feeding both male and female rats (10 male, 10 female daily with the test substance at the doses of 300, 600 and 1,200 mg/kg body weight continuously for 90 days. The examinations of signs, animal behavior and health monitoring showed no abnormalities in the test groups as compared to the controls. The test and control groups (on the 90th day and the satellite group (on the 118th day were analyzed by measuring their final body and organ weights, taking necropsy, and examining hematology, blood clinical chemistry and histopathology. The results suggest that the water extract from the dried fruits of P. nigrum does not cause acute or subchronic toxicities in either male or female rats.

  1. What Is Dry Eye?

    Medline Plus

    Full Text Available ... Tips & Prevention News Ask an Ophthalmologist Patient Stories Español Eye Health / Eye Health A-Z Dry Eye ... Eye Treatment What Is Dry Eye? Leer en Español: ¿Qué es el ojo seco? Written By: Kierstan ...

  2. Dry eye syndrome

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000426.htm Dry eye syndrome To use the sharing features on this page, ... second-hand smoke exposure Cold or allergy medicines Dry eye can also be caused by: Heat or ... Symptoms may include: Blurred vision Burning, itching, ...

  3. Dry Mouth (Xerostomia)

    Science.gov (United States)

    ... mouth Trouble chewing, swallowing, tasting, or speaking A burning feeling in the mouth A dry feeling in the throat Cracked lips ... Food and Drug Administration provides information on dry mouth and offers advice for ... Syndrome Clinic NIDCR Sjogren’s Syndrome Clinic develops new therapies ...

  4. Egg weights, egg component weights, and laying gaps in Great Tits (Parus major) in relation to ambient temperature

    NARCIS (Netherlands)

    Lessells, C.M.; Dingemanse, N.J.; Both, C.; Blem, C.

    2002-01-01

    We collected 328 freshly laid Great Tit (Parus major) eggs from 38 clutches in 1999 to determine the relationship of whole egg weight, wet yolk weight, wet albumen weight, dry shell weight, and the occurrence of laying gaps with mean ambient temperature in the three days preceding laying, while

  5. Egg weights, egg component weights, and laying gaps in great tits (Parus major) in relation to ambient temperature.

    NARCIS (Netherlands)

    Lessells, C.M.; Dingemanse, N.J.; Both, C.

    2002-01-01

    We collected 328 freshly laid Great Tit (Parus major) eggs from 38 clutches in 1999 to determine the relationship of whole egg weight, wet yolk weight, wet albumen weight, dry shell weight, and the occurrence of laying gaps with mean ambient temperature in the three days preceding laying, while

  6. Neutron activation analysis of Ca, Cl, K, Mg, Mn, Na, P, and Sr contents in the crowns of human permanent teeth

    International Nuclear Information System (INIS)

    Zaichick, V.

    2009-01-01

    The effect of age and gender on chemical element contents in intact crowns of permanent teeth of 84 apparently healthy 15-55 year old women (n 38) and men (n = 46) was investigated. Mass fractions of Ca, Cl, K, Mg, Mn, Na, P, and Sr in crowns were determined by instrumental neutron activation analysis using short-lived radionuclides. Mean values (M ± SEL) for female and male combined were (on dry weight basis): 350 ± 5 g/kg, 2920± 150 mg/kg, 839 ± 80 mg/kg, 4880 ± 240 mg/kg, 3.20 ± 0.30 mg/kg, 6240 ± 140 mg/kg, 181 ± 4 g/kg, and 293 ± 24 mg/kg respectively. A statistically significant decrease of Sr (P ≤ 0.01) and increase of Na (P ≤ 0.01) content in the tooth crowns with age was found for women. Sex-related comparison did not show any differences. (author)

  7. Assessment of Osmotic Pre-Drying Treatment on Drying Rates of Fresh Tomato Fruits

    Directory of Open Access Journals (Sweden)

    P. A. Idah

    2014-06-01

    Full Text Available The aim of this work is to investigate the influence of osmotic pre-drying treatments on drying rates of tomato (Lycopersiconesculentum at various drying temperatures. Fresh Roma tomato fruit samples were sliced to a thickness of 5 mm and the seeds were removed. Weight of 300 g was measured for each of the three replicates and immersed in a hypertonic solution of sucrose of different concentrations 40 and 60 oBrix each held for osmotic duration of 1 and 2 hours, drained for 10 min and then dried at 50, 60, and 70 oC in a mechanical dryer. Control samples were also weighed 300 g per replicate and dried at 50, 60, and 70 oC without pre-drying treatment. The initial moisture content of fresh tomato used was 94.5% (wb. Moisture loss of each sample was monitored and recorded hourly until the product has reached the desired final moisture content (≤ 7%.The data collected were subjected to statistical analysis of variance (ANOVA and Duncan New Multiple range tests (DNMRT to ascertain the level of significance differences between the individual treatments and their interaction at p ≤ 0.05.The results show that at all the drying temperatures used, the control tomato samples exhibited the fastest drying rate with an average of 35.2 g/hr, samples pre-treated at 40 oBrix has an average drying rate of 26.6 g/hr, while samples pre-treated at 60 oBrix has the slowest drying rate of 25.2 g/hr. It was also revealed that samples subjected to 1 hour osmotic time have faster drying rates than those treated for 2 hours osmotic time.

  8. Dry well cooling device

    International Nuclear Information System (INIS)

    Suzuki, Hiroyuki.

    1997-01-01

    A plurality of blowing ports with introduction units are disposed to a plurality of ducts in a dry well, and a cooling unit comprising a cooler, a blower and an isolating valve is disposed outside of the dry well. Cooling air and the atmosphere in the dry well are mixed to form a cooling gas and blown into the dry well to control the temperature. Since the cooling unit is disposed outside of the dry well, the maintenance of the cooling unit can be performed even during the plant operation. In addition, since dampers opened/closed depending on the temperature of the atmosphere are disposed to the introduction units for controlling the temperature of the cooling gas, the temperature of the atmosphere in the dry well can be set to a predetermined level rapidly. Since an axial flow blower is used as the blower of the cooling unit, it can be contained in a ventilation cylinder. Then, the atmosphere in the dry well flowing in the ventilation cylinder can be prevented from leaking to the outside. (N.H.)

  9. Radiation data input for the design of dry or semi-dry U tailings disposal

    International Nuclear Information System (INIS)

    Kvasnicka, J.

    1986-01-01

    Before discussion of design criteria for the handling of dry or semi-dry tailings, it is necessary to obtain an insight into the radiation levels associated with the tailings particles and to study the basic physical properties of dry tailings. This article presents the experimental results of assessing Ra and specific alpha-activity distribution with respect to particle size of the Ranger (RUM) and Nabarlek (QML) uranium mines dry tailings samples. The variation of Rn emanation coefficient versus particle size of dry tailings has also been measured. The nuclear-track detection technique, gamma spectrometry and alpha counting were used for the above measurements. Surface Rn flux from the hypothetical Nabarlek semi-infinite dry tailings pile is 32 Bq m -2 s -1 and the Rn flux for Ranger is 10 Bq m -2 s -1 . The theoretical exposure rates for 1 m above these hypothetical tailings piles are 0.95 microC kg -1 h -1 and 0.28 microC kg -1 h -1 , respectively. The derived air alpha-contamination limits (DAAC) for the tailings dust were calculated to be 1.2 Bq m -3 for workers and 0.034 Bq m -3 for a member of the public. The limit for workers corresponds to the air tailings dust concentration of 0.79 mg m -3 for QML tailings and 2.2 mg m -3 for RUM tailings. The DAAC limit for the public corresponds to the air tailings dust concentration of 0.022 mg m -3 for QML tailings and 0.064 mg m -3 for RUM tailings

  10. Characteristics of Timbers Dried Using Kiln Drying and Radio Frequency-Vacuum Drying Systems

    OpenAIRE

    Rabidin Zairul Amin; Seng Gan Kee; Wahab Mohd Jamil Abdul

    2017-01-01

    Heavy hardwoods are difficult-to-dry timbers as they are prone to checking and internal stresses when dried using a conventional kiln drying system. These timbers are usually dried naturally to reach 15% to 19% moisture content with an acceptable defects. Besides long drying time, timbers at these moisture contents are not suitable for indoor applications since they will further dry and causing, for example, jointing and lamination failures. Drying to a lower moisture content could only be ac...

  11. Drying equipment for radioisotope-treated animals

    International Nuclear Information System (INIS)

    Fujikake, Toshio; Ohmori, Akira; Takada, Yukio; Nakano, Shozoh; Tamai, Shinsuke.

    1978-01-01

    The animal experiments using radioisotopes have been carried out over wide fields, accordingly, the number of radioisotope-contaminated animal cadavers has been increasing rapidly. It was decided that each establishment employing radioiosotopes dries those cadavers to such state as to be able to burn up with the device in Japan Atomic Energy Research Institute. The animal waste-drying device meeting the above mentioned purpose was developed by the joint work of Fuji Electric General Devices Co. and Fuji Electric Co. It is known as the micro-wave drying device for animals (its nickname is Microdry). This device dehydrates at high speed by micro-wave drying method. By using along with a moisture detector, it gives the drying state as requested regardless of the water content of each animal. The animal wastes after perfect dehydration are reduced to the weight of about one-third, and the dried animal cadavers can be preserved for a long time at room temperature because of the sterilizing effect of the micro-wave heating. This device is noted for its excellent safeness, simple operation, and low treatment cost. It is anticipated that it can be further applied to other fields such as excreta, breeding materials, etc. (Kobatake, H.)

  12. Healthy Weight

    Science.gov (United States)

    ... such diets limit your nutritional intake, can be unhealthy, and tend to fail in the long run. The key to achieving and maintaining a healthy weight isn't about short-term dietary changes. It's about a lifestyle that includes healthy eating, regular physical activity, and ...

  13. Corrosion analysis of AlMg2 and AlMgSi using electrochemical method

    International Nuclear Information System (INIS)

    Dian A; Maman Kartaman; Rosika K; Yanlinastuti

    2014-01-01

    Corrosion test of cladding materials and structures of research reactor fuel, AlMgSi and AlMg2 have been performed in demineralized water of pH 2 and 6.7 using an electrochemical method. Corrosion phenomenon is affected by several factor such as composition and condition of solution. The purpose of this activity is to investigate the corrosion phenomena through the determination of the parameters of corrosion and polarization curve. The materials used are AlMg2 and AlMgSi alloy in circular dish shape with an area of 1 Cm"2. Preparation of the test sample is performed through several stages polishing, cleaning and drying procedures followed ASTM G3. The electrochemical method is done by measuring the open circuit potential (OCP), polarization resistance and potentiodynamic in demineralized water of pH 2 and pH 6.7 at temperature of 25°C. The results of the OCP is the corrosion potential (Ecorr) of AlMg2 and AlMgSi each of -906.1 mV and -619.8 mV at pH 2 and -868.6 and -756.7 mV at pH 6.7 mV. The results of measurements by polarization resistance technique showed that the corrosion rate of AlMg2 and AlMgSi in safe category (<2 mpy) at pH 6.7 and at pH 2 corrosion rate increased significantly, but still in the lightweight category (<20 mpy). Potentiodynamic curves showed that the passivation at pH 6.7 is very low while the passivation at pH 2 occurs within a relatively short range potential and followed events corroded. (author)

  14. What Is Dry Eye?

    Medline Plus

    Full Text Available ... seasonal allergens and dry eye Apr 27, 2015 Choosing Wisely When It Comes to Eye Care, Part ... Name: Member ID: * Phone Number: * Email: * Enter code: * Message: Thank you Your feedback has been sent.

  15. What Is Dry Eye?

    Medline Plus

    Full Text Available ... month dissolvable punctal plug be removed or pushed down the tear duct to insert a permanent punctal ... Your Eyelid Nov 29, 2017 New Dry Eye Treatment is a Tear-Jerker Jul 21, 2017 Three ...

  16. Dry Skin Relief

    Science.gov (United States)

    ... on a budget Skin care products Skin care secrets Skin lighteners Skin of color Summer skin problems ... condition, such as eczema. Additional related information Dermatologists' top tips for relieving dry skin FIND A DERMATOLOGIST ...

  17. Dry process potentials

    International Nuclear Information System (INIS)

    Faugeras, P.

    1997-01-01

    Various dry processes have been studied and more or less developed in order particularly to reduce the waste quantities but none of them had replaced the PUREX process, for reasons departing to policy errors, un-appropriate demonstration examples or too late development, although realistic and efficient dry processes such as a fluoride selective volatility based processes have been demonstrated in France (CLOVIS, ATILA) and would be ten times cheaper than the PUREX process. Dry processes could regain interest in case of a nuclear revival (following global warming fears) or thermal wastes over-production. In the near future, dry processes could be introduced in complement to the PUREX process, especially at the end of the process cycle, for a more efficient recycling and safer storage (inactivation)

  18. Freeze drying method

    International Nuclear Information System (INIS)

    Coppa, N.V.; Stewart, P.; Renzi, E.

    1999-01-01

    The present invention provides methods and apparatus for freeze drying in which a solution, which can be a radioactive salt dissolved within an acid, is frozen into a solid on vertical plates provided within a freeze drying chamber. The solid is sublimated into vapor and condensed in a cold condenser positioned above the freeze drying chamber and connected thereto by a conduit. The vertical positioning of the cold condenser relative to the freeze dryer helps to help prevent substances such as radioactive materials separated from the solution from contaminating the cold condenser. Additionally, the system can be charged with an inert gas to produce a down rush of gas into the freeze drying chamber to also help prevent such substances from contaminating the cold condenser

  19. What Is Dry Eye?

    Medline Plus

    Full Text Available ... removed or pushed down the tear duct to insert a permanent punctal plug? Sep 12, 2017 Why ... Eye from Jennifer Aniston Sep 02, 2016 The link between seasonal allergens and dry eye Apr 27, ...

  20. Cold Vacuum Drying Facility

    Data.gov (United States)

    Federal Laboratory Consortium — Located near the K-Basins (see K-Basins link) in Hanford's 100 Area is a facility called the Cold Vacuum Drying Facility (CVDF).Between 2000 and 2004, workers at the...

  1. Weighted approximation with varying weight

    CERN Document Server

    Totik, Vilmos

    1994-01-01

    A new construction is given for approximating a logarithmic potential by a discrete one. This yields a new approach to approximation with weighted polynomials of the form w"n"(" "= uppercase)P"n"(" "= uppercase). The new technique settles several open problems, and it leads to a simple proof for the strong asymptotics on some L p(uppercase) extremal problems on the real line with exponential weights, which, for the case p=2, are equivalent to power- type asymptotics for the leading coefficients of the corresponding orthogonal polynomials. The method is also modified toyield (in a sense) uniformly good approximation on the whole support. This allows one to deduce strong asymptotics in some L p(uppercase) extremal problems with varying weights. Applications are given, relating to fast decreasing polynomials, asymptotic behavior of orthogonal polynomials and multipoint Pade approximation. The approach is potential-theoretic, but the text is self-contained.

  2. Dry flue gas desulfurization byproducts as amendments for reclamation of acid mine spoil

    International Nuclear Information System (INIS)

    Dick, W.A.; Stehouwer, R.C.; Beeghly, J.H.; Bigham, J.M.; Lal, R.

    1994-01-01

    Development of beneficial reuses of highly alkaline, dry flue gas desulfurization (FGD) byproducts can impact the economics of adopting these FGD technologies for retrofit on existing powerplants. Greenhouse studies were conducted to evaluate the use of two dry FGD byproducts for reclamation of acid mine spoil (pH, 3.1 to 5.8). Treatment rates of FGD ranges from 0% to 32% by dry weight and most treatments also included 6% by dry weight of sewage sludge. Fescue (Festuca arundinacea Schreb.) was harvested monthly for a total of six harvests. Plant tissue composition and root growth were determined after the sixth harvest. Leachate analyses and pH determination of mixes were done at the beginning and end of the experiments. Both FGD byproducts were effective in raising the spoil pH and in improving fescue growth. At the highest FGD application rate, fescue growth decreased from the optimum due to high pH and reduced rooting volume caused by cementation reactions between the FGD and spoil. Trace elements, with the exception of B, were decreased in the fescue tissue when FGD was applied. Leachate pH, electrical conductivity, dissolved organic carbon, Ca, Mg, and S tended to increase with increased FGD application rate; Al, Fe, Mn, and Zn decreased. pH was the most important variable controlling the concentrations of these elements in the leachate. Concentrations of elements of environmental concern were near or below drinking water standard levels. These results indicate that FGD applied at rates equivalent to spoil neutralization needs can aid in the revegetation of acid spoil revegetation with little potential for introduction of toxic elements into the leachate water or into the food chain

  3. Antioxidant capacity and total phenolic content of air-dried cape gooseberry (Physalis peruviana L. at different ripeness stages

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo Narváez-Cuenca

    2014-08-01

    Full Text Available Because the use of drying at high temperatures might negatively affect the functional properties of fruits, the effect of air-drying at 60°C on the total phenolic content (TPC and antioxidant capacity (AOC of cape gooseberry fruit was evaluated at three ripeness stages. The AOC was evaluated with 2,2'-azino-bis(3- ethylbenzothiazoline-6-sulfonic acid (ABTS , ferric reducing ability of plasma (FRAP, 1,1-diphenyl-2-picrylhydrazyl (DPPH, and beta-carotene-linoleate assays. The TPC and AOC increased in the fresh fruit as the ripeness stage increased. The TPC increased from 401.8±19.8 to 569.3±22.3 mg GA E/100 g dry weight (DW. The AOC values obtained with ABTS in the fresh fruit (ranging from 79.4±4.5 to 132.7±12.9 mumol trolox/g fruit DW were comparable to those obtained with FRAP (ranging from 82.9±16.3 to 153.9±31.7 mumol trolox/g fruit DW. The values assessed with DPPH ranged from 21.0±3.2 to 34.1±5.1 mumol trolox/g fruit DW. The beta-carotene-linoleate assay gave values ranging from 5.8±1.1 to 12.7±2.0 mumol a-tocoferol/g fruit DW. Air-drying the cape gooseberry fruit had a small influence on the TPC. The air-dried fruit had AOC values ranging from 27 to 164% of the value of the fresh fruit. While the ABTS assay produced higher values in the air-dried fruit than in the fresh fruit, the FRAP, DPPH, and beta-carotene-linoleate assays resulted in lower values in the air-dried fruit.

  4. In vivo Confocal Microscopy Evaluation of Meibomian Gland Dysfunction in Dry Eye Patients with Different Symptoms

    Directory of Open Access Journals (Sweden)

    Hui Zhao

    2016-01-01

    Conclusions: IVCM application provides a strong support to differentiate dry eye patients with different symptoms: meibomian gland dysfunction (MGD plays a pivotal role in dry eye aggravation, and using IVCM to observe MG fibrosis, changes in size and density of MG as well as status of inflammation cells can help not only correctly diagnose the type and severity of dry eye, but also possibly prognosticate in routine eye examination in the occurrence of MGD.

  5. Dry body weight: water and sodium removal targets in PD

    NARCIS (Netherlands)

    Krediet, Raymond T.

    2006-01-01

    BACKGROUND/AIMS: Cardiovascular mortality is high in peritoneal dialysis patients. This may be due to the presence of hypertension and fluid overload. Dietary intake of water and sodium are likely to be important, especially in anuric patients. METHODS: A review of the literature on assessment of

  6. Changes in micronutrients, dry weight and plant growth of soybean ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-06-03

    Jun 3, 2008 ... of soybean (Glycine max L. Merrill) cultivars under salt stress. Murat Tunçturk1* ... Salinity stress negatively affected soybean cultivars and the extent of ... INTRODUCTION. Soybean is a ..... A general approach. Science 210: ...

  7. Rapid isolation of high molecular weight DNA from single dried ...

    African Journals Online (AJOL)

    ANAND

    For studying genetic diversity in populations of predatory coccinellid, Cryptolaemus montrouzieri. Mulsant (Coccinellidae: Coleoptera), our attempts to isolate high quality DNA from individual adult beetle using several previously reported protocols and even modifications were quite unsuccessful as the insect size was small ...

  8. Mushroom drying with solar assisted heat pump system

    International Nuclear Information System (INIS)

    Şevik, Seyfi; Aktaş, Mustafa; Doğan, Hikmet; Koçak, Saim

    2013-01-01

    Highlights: • Experimental investigation of a simple and cost effective solar assisted heat pump system. • Developing of a computer program for a drying system with different scenarios by using PLC. • Obtained less energy input with high coefficients of performance of system and more quality products. • Determination of mushroom drying properties such as moisture content, moisture ratio and drying ratio. - Abstract: In this study, a simple and cost effective solar assisted heat pump system (SAHP) with flat plate collectors and a water source heat pump has been proposed. Mushroom drying was examined experimentally in the drying system. Solar energy (SE) system and heat pump (HP) system can be used separately or together. A computer program has been developed for the system. Drying air temperature, relative humidity, weight of product values, etc. were monitored and controlled with different scenarios by using PLC. This system is cheap, good quality and sustainable and it is modeled for good quality product and increased efficiency. Thus, products could be dried with less energy input and more controlled conditions. Mushrooms were dried at 45 °C and 55 °C drying air temperature and 310 kg/h mass flow rate. Mushrooms were dried from initial moisture content 13.24 g water/g dry matter (dry basis) to final moisture content 0.07 g water/g dry matter (dry basis). Mushrooms were dried by using HP system, SE system and SAHP system respectively at 250–220 min, at 270–165 min and at 230–190 min. The coefficients of performance of system (COP) are calculated in a range from 2.1 to 3.1 with respect to the results of experiments. The energy utilization ratios (EURs) were found to vary between 0.42 and 0.66. Specific moisture extraction rate (SMER) values were found to vary between 0.26 and 0.92 kg/kW h

  9. Quasicrystal-reinforced Mg alloys.

    Science.gov (United States)

    Kyun Kim, Young; Tae Kim, Won; Hyang Kim, Do

    2014-04-01

    The formation of the icosahedral phase (I-phase) as a secondary solidification phase in Mg-Zn-Y and Mg-Zn-Al base systems provides useful advantages in designing high performance wrought magnesium alloys. The strengthening in two-phase composites (I-phase + α -Mg) can be explained by dispersion hardening due to the presence of I-phase particles and by the strong bonding property at the I-phase/matrix interface. The presence of an additional secondary solidification phase can further enhance formability and mechanical properties. In Mg-Zn-Y alloys, the co-presence of I and Ca 2 Mg 6 Zn 3 phases by addition of Ca can significantly enhance formability, while in Mg-Zn-Al alloys, the co-presence of the I-phase and Mg 2 Sn phase leads to the enhancement of mechanical properties. Dynamic and static recrystallization are significantly accelerated by addition of Ca in Mg-Zn-Y alloy, resulting in much smaller grain size and more random texture. The high strength of Mg-Zn-Al-Sn alloys is attributed to the presence of finely distributed Mg 2 Sn and I-phase particles embedded in the α -Mg matrix.

  10. Tuning the composition of metastable CoxNiyMg100−xy(OH)(OCH3) nanoplates for optimizing robust methane dry reforming catalyst

    DEFF Research Database (Denmark)

    Fan, Xiaoli; Liu, Zhiting; Zhu, Yi-An

    2015-01-01

    of the metastable precursor CoxNiyMg100−x−y(OH)(OCH3) derived from solvothermal synthesis. The catalyst composition and reaction conditions have been modulated to achieve maximum coke resistance and catalyst stability. Long-term stability for 1000 h time on stream at 800°C has been achieved for the optimized Co0.......075Ni7.425Mg92.5O catalyst. The role of Co in the catalyst has been disclosed through kinetic measurements and detailed characterization of the spent catalysts. Co is enriched on the Co–Ni alloy surface under reforming conditions and accelerates the gasification of coke intermediates. Co also enhances...

  11. Engineering of EPA/DHA omega-3 fatty acid production by Lactococcus lactis subsp. cremoris MG1363.

    Science.gov (United States)

    Amiri-Jami, Mitra; Lapointe, Gisele; Griffiths, Mansel W

    2014-04-01

    Eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) have been shown to be of major importance in human health. Therefore, these essential polyunsaturated fatty acids have received considerable attention in both human and farm animal nutrition. Currently, fish and fish oils are the main dietary sources of EPA/DHA. To generate sustainable novel sources for EPA and DHA, the 35-kb EPA/DHA synthesis gene cluster was isolated from a marine bacterium, Shewanella baltica MAC1. To streamline the introduction of the genes into food-grade microorganisms such as lactic acid bacteria, unnecessary genes located upstream and downstream of the EPA/DHA gene cluster were deleted. Recombinant Escherichia coli harboring the 20-kb gene cluster produced 3.5- to 6.1-fold more EPA than those carrying the 35-kb DNA fragment coding for EPA/DHA synthesis. The 20-kb EPA/DHA gene cluster was cloned into a modified broad-host-range low copy number vector, pIL252m (4.7 kb, Ery) and expressed in Lactococcus lactis subsp. cremoris MG1363. Recombinant L. lactis produced DHA (1.35 ± 0.5 mg g(-1) cell dry weight) and EPA (0.12 ± 0.04 mg g(-1) cell dry weight). This is believed to be the first successful cloning and expression of EPA/DHA synthesis gene cluster in lactic acid bacteria. Our findings advance the future use of EPA/DHA-producing lactic acid bacteria in such applications as dairy starters, silage adjuncts, and animal feed supplements.

  12. Dried culture of the fungus Aspergillus oryzae for saccharification in alcohol production

    Energy Technology Data Exchange (ETDEWEB)

    Drazhner, T M; Ashkinuzi, Z K; El' chits, S V

    1963-01-01

    Dried A. oryzae in place of malt in saccharification of starch-containing grain mash is known to save valuable grain, labor, and space. Laboratory tests showed adequate amylolytic, dextrinolytic, and maltase activity even after nine months storage. Treatment with 0.1% formalin for one hour or with the filtrate of a calcium hypochlorite solution containing 700 mg/l active chlorine for two hours prevented growth of contaminating microflora for 24 hours of fermentation and was not detrimental. Reduction of dried culture needed for saccharification from 8 to 10 to 3.5 to 4% by weight of the starch in the raw material was possible by 2 methods: (1) a l-stage addition at 40/sup 0/, or (2) a 2-stage introduction: 20 to 25% into the sugaring vessel at 57 to 59/sup 0/ and the rest into the fermentation vat after yeast is added. Method 2 avoids the viscosity problem. Alcohol yield was essentially the same as with malt. An industrial test for a 66-hour fermentation confirmed the advantages of the 2-stage method. Higher acidity of final broth did not affect the results because mold enzymes are more resistant to this factor than are those of malt. Nor is higher dry content, the result of breakdown of hemicellulose, cellulose, and pentosans by mold enzymes, a marked disadvantage.

  13. The effect of slicing type on drying kinetics and quality of dried carrot

    Directory of Open Access Journals (Sweden)

    M Naghipour zadeh mahani

    2016-04-01

    Full Text Available Introduction: Carrot is one of the most common vegetables used for human nutrition because of its high vitamin and fiber contents. Drying improves the product shelf life without addition of any chemical preservative and reduces both the size of package and the transport cost. Drying also aidsto reduce postharvest losses of fruits and vegetables especially, which can be as high as 70%. Dried carrots are used in dehydrated soups and in the form of powder in pastries and sauces. The main aim of drying agricultural products is decrease the moisture content to a level which allows safe storage over an extended period. Many fruits and vegetables can be sliced before drying.because of different tissue of a fruit or vegetable, cutting them in different direction and shape created different tissue slices. Due to drying is the exiting process of the moisture from internal tissue so different tissue slices caused different drying kinetics. Therefore, the study on effect of cutting parameters on drying is necessary. Materials and Methods: Carrots (Daucus carota L. were purchased from the local market (Kerman, Iran and stored in a refrigerator at 5°C. The initial moisture contents of the Carrot samples were determined by the oven drying method. The sample was dried in an oven at 105±2°C about 24 hours. The carrots cut by 3 models blade at 3 directions. The samples were dried in an oven at 70°C. Moisture content of the carrot slices were determined by weighting of samples during drying. Volume changes because of sample shrinkage were measured by a water displacement method. Rehydration experiment was performed by immersing a weighted amount of dried samples into hot water 50 °C for 30 min. In this study the effect of some cutting parameters was considered on carrot drying and the quality of final drying product. The tests were performed as a completely random design. The effects of carrot thickness at two levels (3 and 6 mm, blade in 3 models (flat blade

  14. Drying of Concrete

    DEFF Research Database (Denmark)

    Hansen, Kurt Kielsgaard; Geiker, Mette Rica; Nygaard, Peter Vagn

    2002-01-01

    Estimated and measured relative humidity (RH) change during drying are compared for two concretes, 1: w/c=0.46 and 2: w/(c+0.5fa+2sf)=0.50. The estimations were undertaken by means of the Swedish program TorkaS 1.0. Measurements were performed by RH-sensors type Humi-Guard. Drying of 150 mm thick...... samples from sides at 60% RH and 22 °C took place from 4 to 56 days after casting. At the end of the drying period the measured RH was about 4% lower than the estimated RH at 1/5th depth from the exposed surface for both concretes. In the middle of the samples, the measured RH of concretes 1 and 2 were 2...

  15. SILAGE CANE SUGAR ADDED WITH DRIED BREWER

    Directory of Open Access Journals (Sweden)

    W. J. R. Castro

    2015-02-01

    Full Text Available The objective of this experiment was to evaluate the fermentative parameters and chemical composition of silage cane sugar added with residue dried brewery. The experimental design was completely randomized with four treatments and four replications: 100% cane sugar; 90% of cane sugar + 10% residue dried brewer; 80% of cane sugar + 20% residue dried brewer and 70% cane sugar + 30% dried brewer based on natural matter, composed silages. The sugar cane was chopped in a stationary machine with forage particle size of approximately 2 cm, and homogenized manually with the additives. For storage chopped fresh weight were used in experimental silos capacity of about 4 liters. The results showed that the contents of dry matter and crude protein showed positive linear (P0.05 with mean value of 3.81, while for ether extract and ash results were positive linear (P0.05 for N ammonia presented average value of 4.18. It is concluded that the addition of brewer dehydrated improves the fermentation process of silage cane sugar, in addition to improving their nutritional characteristics.

  16. Safety of dried aerial parts of Hoodia parviflora as a novel food pursuant to Regulation (EC) No 258/97

    DEFF Research Database (Denmark)

    Sjödin, Anders Mikael

    2017-01-01

    provided on the composition, the specifications, the production process, the batch-to-batch variability and the stability of the NF is sufficient and does not raise safety concerns. The applicant intends to use the NF in a number of energy-reduced/sugar-free/no-added-sugar foods in quantities of up to 15......Following a request from the European Commission, the EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA) was asked to deliver a scientific opinion on the dried aerial parts of Hoodia parviflora as a novel food (NF) submitted pursuant to Regulation (EC) No 258/97. The information...... mg per serving. The applicant also proposes to provide the NF as a food supplement. The target population proposed by the applicant is adults. The highest intake estimates were found in the group of elderly (≥ 65 years) individuals, with a high intake of 1.0 mg/kg body weight (bw) per day. One 90-day...

  17. Pecan drying with silica gel

    Energy Technology Data Exchange (ETDEWEB)

    Ghate, S.R.; Chhinnan, M.S.

    1983-07-01

    High moisture in-shell pecans were dried by keeping them in direct and indirect contact with silica gel to investigate their drying characteristics. In-shell pecans were also dried with ambient air from a controlled environment chamber and with air dehumidified by silica gel. Direct contact and dehumidified air drying seemed feasible approaches.

  18. Herbal Weight Loss Pill Overdose: Sibutramine Hidden in Pepper Pill

    Directory of Open Access Journals (Sweden)

    Gul Pamukcu Gunaydin

    2015-01-01

    Full Text Available Supposedly herbal weight loss pills are sold online and are widely used in the world. Some of these products are found to contain sibutramine by FDA and their sale is prohibited. We report a case of a female patient who presented to the emergency department after taking slimming pills. 17-year-old female patient presented to the emergency room with palpitations, dizziness, anxiety, and insomnia. She stated that she had taken 3 pills named La Jiao Shou Shen for slimming purposes during the day. Her vital signs revealed tachycardia. On her physical examination, she was restless, her oropharynx was dry, her pupils were mydriatic, and no other pathological findings were found. Sibutramine intoxication was suspected. She was given 5 mg IV diazepam for restlessness. After supportive therapy and observation in emergency department for 12 hours there were no complications and the patient was discharged home. Some herbal pills that are sold online for weight loss have sibutramine hidden as an active ingredient, and their sale is prohibited for this reason. For people who use herbal weight loss drugs, sibutramine excessive intake should be kept in mind at all times.

  19. Comparative effects of partial rootzone drying and deficit irrigation on growth and physiology of tomato plants

    Directory of Open Access Journals (Sweden)

    Savić Slađana

    2009-01-01

    Full Text Available The effects of partial rootzone drying (PRD, deficit irrigation (DI, and full irrigation (FI on tomato physiology were investigated. In PRD and DI plants, leaf water potential values and stomatal conductance were significantly lower, while xylem ABA concentration was greater compared to FI plants. Photosynthesis was similar for all treatments. Water use efficiency was improved by PRD and DI, which reduced fruit dry weight, but had no effect on dry weight of leaves and stems.

  20. Effect of sterilization process on surface characteristics and biocompatibility of pure Mg and MgCa alloys

    International Nuclear Information System (INIS)

    Liu, X.L.; Zhou, W.R.; Wu, Y.H.; Cheng, Y.; Zheng, Y.F.

    2013-01-01

    The aim of this work was to investigate the effect of various sterilization methods on surface characteristics and biocompatibility of MgCa alloy, with pure Mg as a comparison, including steam autoclave sterilization (SA), ethylene oxide steam sterilization (EO), glutaraldehyde sterilization (GD), dry heat sterilization (DH) and Co60 γ ray radiation sterilization (R) technologies. The surface characterizations were performed by environmental scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, grazing incidence X-ray diffraction, water contact angle and surface free energy measurement, whereas the cytotoxicity and hemocompatibility were evaluated by cellular adhesive experiment, platelet adhesion and hemolysis test. The results showed that the five sterilization processes caused more changes on the surface of MgCa alloy than that on the surface of pure Mg. The GD sterilization caused the most obvious changes on the surface of the pure Mg, and the SA sterilization made the largest alteration on the MgCa alloy surface. The GD and DH sterilization processes could cause increases on surface free energy for both pure Mg and MgCa alloys, while the other three sterilization processes reduced the surface free energy. The DH and GD sterilization processes caused the least alteration on the cell adhesion on pure Mg surface, whereas the EO sterilization performed the greatest impact on the cell adhesion on the Mg–Ca alloy surface. The hemolysis percentage of pure Mg and MgCa alloys were reduced by SA sterilization, meanwhile the other four sterilization processes increased their hemolysis percentages significantly, especially for the EO sterilization. - Highlights: • The effect of sterilization on surface chemistry and biocompatibility was studied. • Sterilization caused more surface changes on MgCa alloy than pure Mg. • Co60 γ ray radiation is the most appropriate sterilization process

  1. Characteristics of Timbers Dried Using Kiln Drying and Radio Frequency-Vacuum Drying Systems

    Directory of Open Access Journals (Sweden)

    Rabidin Zairul Amin

    2017-01-01

    Full Text Available Heavy hardwoods are difficult-to-dry timbers as they are prone to checking and internal stresses when dried using a conventional kiln drying system. These timbers are usually dried naturally to reach 15% to 19% moisture content with an acceptable defects. Besides long drying time, timbers at these moisture contents are not suitable for indoor applications since they will further dry and causing, for example, jointing and lamination failures. Drying to a lower moisture content could only be achieved in artificial drying kilns such as conventional kiln, dehumidification kiln, solar kiln, radio frequency-vacuum, etc. The objective of this study was to evaluate the characteristics of 30 mm and 50 mm thick kekatong (Cynometra spp. timber dried using kiln drying (KD and radio frequency-vacuum drying (RFV system. The investigation involved drying time, moisture content (MC variations between and within boards, drying defects, shrinkage, and drying stress. Drying defects include checks (surface, end, and internal checks and warping (bowing, cuping, spring, and twisting. The results showed that RFV drying time was reduced to 50% compared to the KD. RFV dried boards demonstrated a more uniform MC between and within boards. Shrinkage in width and thickness, as well as tangential/radial and volumetric shrinkages were substantially less in RFV boards. The amount of cupping, bowing and spring were very low and negligible in all drying runs. There was no twisting observed in all drying methods. The number of stress-free RFV board was higher than KD. With proper procedure, the RFV technology could be used for drying heavy hardwoods which are difficult to dry in conventional kilns due to excessive drying times and degradation.

  2. FREEZE DRYING PROCESS: A REVIEW

    OpenAIRE

    Soham Shukla

    2011-01-01

    Among the various methods of drying, this article has mentioned only one most important method, “Freeze drying”. This method is mainly used for the drying of thermo labile materials. This method works on the principle of sublimation. This method is divided into 3 steps for its better understanding; these are Freezing, Primary drying, and secondary drying. There are many advantages and disadvantages of this method, but still this is the most useful drying method nowadays.

  3. Dry piston coal feeder

    Science.gov (United States)

    Hathaway, Thomas J.; Bell, Jr., Harold S.

    1979-01-01

    This invention provides a solids feeder for feeding dry coal to a pressurized gasifier at elevated temperatures substantially without losing gas from the gasifier by providing a lock having a double-acting piston that feeds the coals into the gasifier, traps the gas from escaping, and expels the trapped gas back into the gasifier.

  4. Dry Macular Degeneration

    Science.gov (United States)

    ... a combination of heredity and environmental factors, including smoking and diet. The condition develops as the eye ages. Dry ... nonsmokers. Ask your doctor for help to stop smoking. Maintain a ... controlling your diet. Choose a diet rich in fruits and vegetables. ...

  5. Essays on Dry Ports

    NARCIS (Netherlands)

    G.G. Chandrakant (Gujar)

    2011-01-01

    textabstractDue to several reasons, currently the global supply chains are getting stretched further away into the hinterlands from the gateway seaports. This single fact enhances the importance of dry ports. It would not be against logic, to state that in coming times, as a result of ever-growing

  6. What Is Dry Eye?

    Medline Plus

    Full Text Available ... bloodshot when I wake up? Jun 26, 2016 Why are my eyes dry after LASIK? Jun 19, 2016 Can I be tested whether I close my eyes when I sleep? Feb 10, 2016 Can light sensitivity from Parkinson’s ...

  7. Infrared Drying Parameter Optimization

    Science.gov (United States)

    Jackson, Matthew R.

    In recent years, much research has been done to explore direct printing methods, such as screen and inkjet printing, as alternatives to the traditional lithographic process. The primary motivation is reduction of the material costs associated with producing common electronic devices. Much of this research has focused on developing inkjet or screen paste formulations that can be printed on a variety of substrates, and which have similar conductivity performance to the materials currently used in the manufacturing of circuit boards and other electronic devices. Very little research has been done to develop a process that would use direct printing methods to manufacture electronic devices in high volumes. This study focuses on developing and optimizing a drying process for conductive copper ink in a high volume manufacturing setting. Using an infrared (IR) dryer, it was determined that conductive copper prints could be dried in seconds or minutes as opposed to tens of minutes or hours that it would take with other drying devices, such as a vacuum oven. In addition, this study also identifies significant parameters that can affect the conductivity of IR dried prints. Using designed experiments and statistical analysis; the dryer parameters were optimized to produce the best conductivity performance for a specific ink formulation and substrate combination. It was determined that for an ethylene glycol, butanol, 1-methoxy 2- propanol ink formulation printed on Kapton, the optimal drying parameters consisted of a dryer height of 4 inches, a temperature setting between 190 - 200°C, and a dry time of 50-65 seconds depending on the printed film thickness as determined by the number of print passes. It is important to note that these parameters are optimized specifically for the ink formulation and substrate used in this study. There is still much research that needs to be done into optimizing the IR dryer for different ink substrate combinations, as well as developing a

  8. Avaliação de três cultivares de Panicum maximum Jacq. sob pastejo: composição da dieta, consumo de matéria seca e ganho de peso animal Evaluation of three varieties of Panicum maximum Jacq. under grazing: diet composition, dry matter intake and animal weight gain

    Directory of Open Access Journals (Sweden)

    Patrícia Amarante Brâncio

    2003-10-01

    Full Text Available Três cultivares de Panicum maximum Jacq. submetidos a pastejo rotativo foram avaliados ao longo do ano, antes e após o período de pastejo, quanto à composição botânica e química da dieta, consumo de matéria seca e ganho de peso animal. Os tratamentos constituíram em: 1 cv. Tanzânia + 50 kg/ha de N, 2 cv. Tanzânia + 100 kg/ha de N, 3 cv. Mombaça + 50 kg/ha de N, e 4 cv. Massai + 50 kg/ha de N. As dietas selecionadas pelos animais na cv. Massai tenderam a apresentar os menores valores de digestibilidade e proteína bruta e os maiores de fibra em detergente neutro, enquanto na cv. Mombaça as dietas continham, em geral, maiores teores de sílica. Os animais selecionaram, em média, 92,4% de folhas verdes, independentemente do tratamento e da época de amostragem. Os animais consumiram semelhantes quantidades de forragem nos diversos tratamentos, apresentando, em média, consumos de 1,9; 2,8; 3,4; e 2,3 kgMS/100kgPV, respectivamente, em junho, setembro e novembro de 1998 e março de 1999. Os piores resultados quanto ao ganho de peso por animal foram verificados na cv. Massai, mas, devido a sua alta capacidade de suporte na época chuvosa, superou a cv. Mombaça e cv. Tanzânia + 50 kg/ha de N, em termos de ganho de peso por área. A participação de folhas, a altura do pasto, o teor de proteína bruta da dieta selecionada pelos animais e o tamanho de bocado foram os fatores que mais influenciaram positivamente o ganho de peso animal.Three varieties of Panicum maximum Jacq. were evaluated by measuring the botanical and chemical composition of the diet, and the dry matter intake and weight gain of the animal under rotational grazing, before and after a period of grazing. The treatments were: 1 v. Tanzânia + 50 kg N/ha, 2 v. Tanzânia + 100 kg N/ha, 3 v. Mombaça + 50 kg N/ha, and 4 v. Massai + 50 kg N/ha. Of the diets selected by the animals, v. Massai tended to show lower values for digestibility and crude protein, and higher values

  9. Stabilization of Reactive MgO Surfaces by Ni Doping

    Science.gov (United States)

    Mazheika, Aliaksei; Levchenko, Sergey V.

    Ni-MgO solid solutions are promising materials for catalytic reduction of CO2 and dry reforming of CH4. To explain the catalytic activity, an ab initio study of Ni-substitutional defects in MgO (NiMg) has been performed. At first, the validation of the theory level was done. We compared results of CCSD(T) embedded-cluster calculations of NiMg formation energies and adsorption energies of CO, CO2 and H2 on them to the HSE(α) hybrid DFT functional with the fraction of the exact exchange α varied between 0 and 1. HSE(0.3) was found to be the best compromise in this study. Our periodic HSE(0.3) calculations show that NiMg defects are most stable at corner sites, followed by steps, and are least stable at (001) terraces. Thus, Ni-doping stabilizes stepped MgO surfaces. The dissociative adsorption of H2 on the terrace is found to be endothermic (+ 1 . 1 eV), whereas on (110) surface with NiMg it is highly exothermic (- 1 . 6 eV). Adsorbed CO2 is also significantly stabilized (- 0 . 6 vs. - 2 . 2 eV). These findings explain recent microcalorimetry measurements of H2 and CO2 adsorption at doped Ni-MgO samples. partially supported by UniCat (Deutsche Forschungsgemeinschaft).

  10. Inhibitory effect of MgSO4 on calcium overload after radiation-induced brain injuries

    International Nuclear Information System (INIS)

    Tu Yu; Zhou Yuying; Wang Lili

    2005-01-01

    Objective: To explore the neuroprotective effect of magnesium sulfate (MgSO 4 ) on radiation-induced acute brain injuries. Methods: A total of 60 mature Sprague-Dawley rats were randomly divided into 3 groups: blank control group, experimental control group and experimental therapy group. The whole brain of SD rats of experimental control group and experimental therapy group was irradiated to a dose of 20 Gy using 6 MeV electrons. Magnesium sulfate was injected intraperitoneally into the rats of experimental therapy group before and after irradiation for five times. At different time points (24 h, 7 days, 14 days, 30 days after irradiation), the brain tissue was taken. Plasma direct reading spectrography was used to measure the contents of Ca 2+ , Mg 2+ in brain tissue, and the percentage of brain water content was calculated with the wet-dry weight formula. Results: Compared with the blank control group, the percentage of brain water and content of Ca 2+ in brain of the experimental control group increased markedly (P 2+ decreased significantly (P 2+ in brain of the experimental therapy group were significantly lower than those of the experimental control group (P<0.05). Conclusion: Magnesium sulfate used in the early stage after irradiation can inhibit the calcium overload in rat brain , and attenuate brain edema and injuries. (authors)

  11. Improved hydrogen sorption kinetics in wet ball milled Mg hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Li

    2011-05-04

    In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ball milling. The improved particle size and specific surface area of wet ball milled MgH{sub 2} powder is found to be determining its hydrogen sorption kinetics especially at relatively low temperatures. And it also shows good cycling sorption behavior, which decides on its industrial applicability. With three different catalysts MgH{sub 2} powder shows improved hydrogen sorption behavior as well as the cyclic sorption behavior. Among them, the Nb{sub 2}O{sub 5} catalyst is found to be the most effective one in this work. Compared to the wet ball milled MgH{sub 2} powder, the particle size and specific surface area of the MgH{sub 2} powder with catalysts are similar to the previous ones, while the grain size of the MgH{sub 2} with catalysts is much finer. In this case, two reasons for hydrogen sorption improvement are suggested: one is the reduction of the grain size. The other may be as pointed out in some literatures that formation of new oxidation could enhance the hydrogen sorption kinetics, which is also the reason why its hydrogen capacity is decreased compared to without catalysts. After further ball milling, the specific surface area of wet ball milled Mg

  12. Microwave energy-assisted formation of bioactive CaO–MgO–SiO2 ...

    Indian Academy of Sciences (India)

    Ogun State, South-west, Nigeria); MgO was obtained from. Mg(NO3)2·6H2O ... 2.3 Extraction of Ca from chicken eggshells. The chicken eggshells were washed with deionized water, oven-dried at .... There is no carbon peak observed .... present in critical concentrations could be biologically active. [28]. .... Solids 354 722.

  13. Dried fruit breadfruit slices by Refractive Window™ technique

    Directory of Open Access Journals (Sweden)

    Diego F. Tirado

    2016-01-01

    Full Text Available A large amount of products are dried due several reasons as preservation, weight reduction and improvement of stability. However, on the market are not offered low-cost and high quality products simultaneously. Although there are effective methods of dehydrating foods such as freeze drying, which preserves the flavor, color and vitamins, they are poor accessibility technologies. Therefore, alternative processes are required to be efficient and economical. The aim of this research was compare drying kinetics of sliced of breadfruit (Artocarpus communis using the technique of Refractive Window® (VR with the tray drying. To carry out this study, sliced of 1 and 2 mm thick were used. Refractive window drying was performed with the water bath temperature to 92 °C; and tray drying at 62 °C and an air velocity of 0.52 m/s. During the Refractive window drying technique, the moisture content reached the lower than tray drying levels. Similarly it happened with samples of 1 mm, which, having a smaller diameter reached lower moisture levels than samples 2 mm. The higher diffusivities were obtained during drying sliced VR 1 and 2 mm with coefficients of 6.13 and 3.90*10-9 m2/s respectively.

  14. Spray Drying Processing: granules production and drying kinetics of droplets

    International Nuclear Information System (INIS)

    Mondragon, R.; Julia, J. E.; Barba, A.; Jarque, J. C.

    2013-01-01

    Spray drying is a unit operation very common in many industrial processes. For each particular application, the resulting granulated material must possess determined properties that depend on the conditions in which the spray drying processing has been carried out, and whose dependence must be known in order to optimize the quality of the material obtained. The large number of variables that influence on the processes of matter and energy transfer and on the formation of granular material has required a detailed analysis of the drying process. Over the years there have been many studies on the spray drying processing of all kind of materials and the influence of process variables on the drying kinetics of the granulated material properties obtained. This article lists the most important works published for both the spray drying processing and the drying of individual droplets, as well as studies aimed at modeling the drying kinetics of drops. (Author)

  15. Cassava Sun Drying Performance on Various Surfaces and Drying ...

    African Journals Online (AJOL)

    Traditional processing methods that include ... The traditional sun drying method is very inefficient as the product can take 2-. 3 days to dry. .... using a digital balance (Ohaus Corporation type). The same applied .... preservation and marketing.

  16. Dry alcohol production plant

    Directory of Open Access Journals (Sweden)

    Stanković Mirjana S.

    2003-01-01

    Full Text Available The IGPC Engineering Department designed basic projects for dry alcohol production plant, using technology developed in the IGPC laboratories. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects a production plant with a capacity of 40 m3/y was manufactured, at "Zorka Pharma", Šabac in 1995-1996. The product meets all quality demands, as well as environmental regulations. The dry alcohol production process is fully automatized. There is no waste in the process, neither gaseous, nor liquid. The chosen process provides safe operation according to temperature regime and resistance in the pipes, air purification columns and filters. Working at increased pressure is suitable for evaporation and condensation at increased temperatures. The production process can be controlled manually, which is necessary during start-up, and repairs.

  17. Stabilization of Live Attenuated Influenza Vaccines by Freeze Drying, Spray Drying, and Foam Drying.

    Science.gov (United States)

    Lovalenti, Phillip M; Anderl, Jeff; Yee, Luisa; Nguyen, Van; Ghavami, Behnaz; Ohtake, Satoshi; Saxena, Atul; Voss, Thomas; Truong-Le, Vu

    2016-05-01

    The goal of this research is to develop stable formulations for live attenuated influenza vaccines (LAIV) by employing the drying methods freeze drying, spray drying, and foam drying. Formulated live attenuated Type-A H1N1 and B-strain influenza vaccines with a variety of excipient combinations were dried using one of the three drying methods. Process and storage stability at 4, 25 and 37°C of the LAIV in these formulations was monitored using a TCID50 potency assay. Their immunogenicity was also evaluated in a ferret model. The thermal stability of H1N1 vaccine was significantly enhanced through application of unique formulation combinations and drying processes. Foam dried formulations were as much as an order of magnitude more stable than either spray dried or freeze dried formulations, while exhibiting low process loss and full retention of immunogenicity. Based on long-term stability data, foam dried formulations exhibited a shelf life at 4, 25 and 37°C of >2, 1.5 years and 4.5 months, respectively. Foam dried LAIV Type-B manufactured using the same formulation and process parameters as H1N1 were imparted with a similar level of stability. Foam drying processing methods with appropriate selection of formulation components can produce an order of magnitude improvement in LAIV stability over other drying methods.

  18. Myasthenia Gravis (MG): Medical Management

    Science.gov (United States)

    ... take effect, prior to surgery or for myasthenic crisis. However, some people receive regular plasmapheresis or IVIg as a supplement to immunosuppressant drugs. Pregnancy In rare cases, pregnancy appears to trigger the onset of MG. ...

  19. Dry mouth during cancer treatment

    Science.gov (United States)

    ... gov/ency/patientinstructions/000032.htm Dry mouth during cancer treatment To use the sharing features on this page, please enable JavaScript. Some cancer treatments and medicines can cause dry mouth. Symptoms you ...

  20. Nitramine Drying & Fine Grinding Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Nitramine Drying and Fine Grinding Facility provides TACOM-ARDEC with a state-of-the-art facility capable of drying and grinding high explosives (e.g., RDX and...

  1. New method measures moisture and true dry mass

    International Nuclear Information System (INIS)

    Frank, H.

    The moisture content of wood can be determined by measuring the nuclear magnetic resonance of free water hydrogen atoms in wood. Nanassy studied NMR curves for six types of wood and obtained the calibration curve by reducing the moisture content in steps by 4% moisture down to ca. 1% moisture and then by gradually wetting the wood. The initial material was fresh wood. For each step he measured the intensity of the free water hydrogen signal. If the sample weight is known the dry matter content (dry weight) and moisture content of the sample can be derived from the measured NMR signal. (J.P.)

  2. Overweight, Obesity, and Weight Loss

    Science.gov (United States)

    ... Back to section menu Healthy Weight Weight and obesity Underweight Weight, fertility, and pregnancy Weight loss and ... section Home Healthy Weight Healthy Weight Weight and obesity Underweight Weight, fertility, and pregnancy Weight loss and ...

  3. Total Diet Study. Mg and Mn content estimation of a Market Basket of Sao Paulo state (Brazil) by Instrumental Neutron Activation

    International Nuclear Information System (INIS)

    Roseane Pagliaro Avegliano; Vera Akiko Maihara

    2014-01-01

    Total Diet Studies (TDS) have been carried out to estimate dietary intakes of the essential and toxic elements for a large-scale population over a specific period of time. In this study, the TDS was based on the evaluation of food representing a Market Basket (MB), which reflected the dietary habits of the Sao Paulo State population, corresponding to 72 % of the average food consumption for the state of Sao Paulo. In the present Total Diet Study, magnesium and manganese concentrations were determined in 30 of the most consumed food groups of a MB of Sao Paulo State, Brazil. Instrumental Neutron Activation Analysis (INAA) has been successfully used on a regularly basis in several areas of nutrition and foodstuffs. Element concentrations were determined by INAA in freeze-dried samples and ranged in mg kg -1 . Mg 41.4 (fats)-5287 (coffee) and Mn 0.12 (prime grade beef)-32.9 (coffee). The average daily Mg and Mn intake was calculated by multiplying the concentration of each element in each table-ready food group by the respective weight (g day -1 ) of the food group in the MB and adding the products from all food groups. The results of daily dietary intakes in this study were: Mg 174.8 and Mn 1.34 mg day -1 . Theses values were lower than the adequate intake (AI) proposed by the Food and Nutrition Board of the Institute of Medicine (USA National Academy) for adults. The low levels of Mg and Mn intakes presented in this TDS are probably due to the fact that MB of this study represented only 72 % of the weight of the most consumed household foods of Sao Paulo State. (author)

  4. A double-blind study comparing ibuprofen 1800 mg or 2400 mg daily and placebo in sports injuries.

    Science.gov (United States)

    Hutson, M A

    1986-01-01

    In a double-blind, placebo-controlled study of forty-six patients with acute ligamentous damage of the knee, ibuprofen in dosages 1800 mg and 2400 mg produced significant improvements in joint mobility, weight bearing ability and match fitness. Joint effusion, pain on stress and pain severity was significantly improved by all three treatments. Only two patients reported side-effects (one while taking placebo and one taking ibuprofen 2400 mg). The study confirmed the efficacy and excellent tolerance to ibuprofen in patients with sports injuries to the knee.

  5. The Effect of Temperature and Drying Method on Drying Time and Color Quality of Mint

    Directory of Open Access Journals (Sweden)

    H Bahmanpour

    2017-10-01

    Full Text Available Introduction Mint (Mentha spicata L. cbelongs to the Lamiaceae family, is an herbaceous, perennial, aromatic and medicinal plant that cultivated for its essential oils and spices. Since the essential oil is extracted from dried plant, choosing the appropriate drying method is essential for gaining high quality essential oil.Vacuum drying technology is an alternative to conventional drying methods and reported by many authors as an efficient method for improving the drying quality especially color characteristics. On the other side, solar dryers are also useful for saving time and energy. In this study the effect of two method of dryings including vacuum-infrared versus solar at three different conventional temperatures (30, 40 and 50°C on mint plant is evaluated while factorial experiment with randomized complete block is applied. Drying time as well as color characteristics areconsidered for evaluation of each method of drying. Materials and Methods Factorial experiment with randomized complete block was applied in order to evaluate the effect of drying methods (vacuum-infrared versus solar and temperature (30, 40 and 50°C on drying time and color characteristics of mint. The initially moisture content of mint leaves measured according to the standard ASABE S358.2 during 24 hours inside an oven at 104 °C. Drying the samples continued until the moisture content (which real time measured reached to 10% wet basis. The components of a vacuum dryer consisted of a cylindrical vacuum chamber (0.335 m3 and a vacuum pump (piston version. The temperature of the chamber was controlled using three infrared bulbs using on-off controller. Temperature and weight of the products registered real time using a data acquisition system. The components of a solar dryer were consisting of a solar collector and a temperature control system which was turning the exhaust fan on and off in order to maintain the specific temperature. A date acquisition system was

  6. Analysis of Drying Process Quality in Conventional Dry-Kilns

    OpenAIRE

    Sedlar Tomislav; Pervan Stjepan

    2010-01-01

    This paper presents testing results of drying quality in a conventional dry kiln. Testing is based on a new methodology that will show the level of success of the drying process management by analyzing the quality of drying process in a conventional dry kiln, using a scientifi cally improved version of the check list in everyday practical applications. A company that specializes in lamel and classic parquet production was chosen so as to verify the new testing methodology. A total of 56 m3 of...

  7. CO{sub 2} capture in Mg oxides doped with Fe and Ni; Captura de CO{sub 2} en oxidos de Mg dopados con Fe y Ni

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez S, I. F.

    2016-07-01

    In this work the CO{sub 2} capture-desorption characteristics in Mg oxides doped with Fe and Ni obtained by the direct oxidation of Mg-Ni and Mg-Fe mixtures are presented. Mixtures of Mg-Ni and Mg-Fe in a different composition were obtained by mechanical milling in a Spex-type mill in a controlled atmosphere of ultra high purity argon at a weight / weight ratio of 4:1 powder using methanol as a lubricating agent, for 20 h. The powders obtained by mechanical milling showed as main phase, the Mg with nanocrystalline structure. Subsequently, the mixtures of Mg-Ni and Mg-Fe were oxidized within a muffle for 10 min at 600 degrees Celsius. By means of X-ray diffraction analysis, the Mg O with nano metric grain size was identified as the main phase, which was determined by the Scherrer equation. In the Mg O doped with Ni, was identified that as the Ni amount 1 to 5% by weight dispersed in the Mg O matrix was increased, the main peak intensity of the Ni phase increased, whereas in the Mg O doped with Fe was observed by XRD, that the Fe{sub 2}O{sub 3} phase was present and by increasing the amount of Fe (1 to 5% by weight) dispersed in the crystalline phase of Mg O, the intensity of this impurity also increased. Sem-EDS analysis showed that the Ni and Fe particles are dispersed homogeneously in the Mg O matrix, and the particles are porous, forming agglomerates. Through energy dispersive spectroscopy analysis, the elemental chemical composition obtained is very close to the theoretical composition. The capture of CO{sub 2} in the Mg O-1% Ni was carried out in a Parr reactor at different conditions of pressure, temperature and reaction time. Was determined that under the pressure of 0.2 MPa at 26 degrees Celsius for 1 h of reaction, the highest CO{sub 2} capture of 7.04% by weight was obtained, while in Mg O-1% Fe the CO{sub 2} capture was 6.32% by weight. The other magnesium oxides doped in 2.5 and 5% by weight Ni and Fe showed lower CO{sub 2} capture. The different stages

  8. Fluid flow in drying drops

    NARCIS (Netherlands)

    Gelderblom, Hanneke

    2013-01-01

    When a suspension drop evaporates, it leaves behind a drying stain. Examples of these drying stains encountered in daily life are coffee or tea stains on a table top, mineral rings on glassware that comes out of the dishwasher, or the salt deposits on the streets in winter. Drying stains are also

  9. Burnup credit in a dry storage module

    International Nuclear Information System (INIS)

    Thornton, J.R.

    1989-01-01

    Comparison of spent fuel storage expansion options available to Oconee Nuclear Station revealed that dry storage could be economically competitive with transshipment and rod consolidation. Economic competitiveness, however, mandated large unit capacity while existing cask handling facilities at Oconee severely limited size and weight. The dry storage concept determined to best satisfy these conflicting criteria is a 24 pressurized water reactor (PWR) fuel assembly capacity NUTECH Horizontal Modular Storage (NUHOMS) system. The Oconee version of the NUHOMS system takes advantage of burnup credit in demonstrating criticality safety. The burnup credit criticality analysis was performed by Duke Power Company's Design Engineering Department. This paper was prepared to summarize the criticality control design features employed in the Oconee NUHOMS-24P DSC basket and to describe the incentives for pursuing a burnup credit design. Principal criticality design parameters, criteria, and analysis methodology are also presented

  10. Hypoglycemic activity of dried extracts of Bauhinia forficata Link.

    Science.gov (United States)

    da Cunha, A M; Menon, S; Menon, R; Couto, A G; Bürger, C; Biavatti, M W

    2010-01-01

    Leaves of the pantropical genus Bauhinia (Fabaceae) are known popularly as cow's foot, due to their unique characteristic bilobed aspect. The species Bauhinia forficata (Brazilian Orchid-tree) is widely used in folk medicine as an antidiabetic. The present work investigates the hypoglycemic activity of the dried extracts of Bauhinia forficata leaves in vivo, as well as the influence of the drying and granulation processes on this activity. The fluid extract was dried to generate oven-dried (ODE), spray-dried (SDE) and wet granulation (WGE) extracts, with the aid of colloidal silicon dioxide and/or cellulose:lactose mixture. The dried extracts were characterized by spectrophotometric, chromatographic and photo microscopy image analysis. 200 mg/kg body wt., p.o. of each dried product were administered orally to male Wistar rats over 7 days old, for biomonitoring of the hypoglycemic activity profile. The effect of the extracts was studied in STZ-induced diabetic rats. After 7 days of treatment, fasting glucose was determined, and the livers were removed, dried on tissue paper, weighed, and stored at -20 degrees C to estimate hepatic glycogen. Our results show that spray-drying or oven-drying processes applied to B. forficata extracts did not significantly alter its flavonoid profile or its hypoglycemic activity. Indeed, the dried extracts of B. forficata act differently from glibenclamide. Despite the lower active content in WGE, because of the higher concentration of adjuvants, the use of the granulation process improved the manufacturing properties of the ODE, making this material more appropriate for use in tablets or capsules.

  11. Effects of Oral Administration of Nicotine on Organ Weight, Serum ...

    African Journals Online (AJOL)

    This study investigated the effects of oral administration of nicotine on body and reproductive organ weight, serum testosterone level and testicular histology in adult male rats. Forty male rats divided into five groups and treated for a period of 30 days with 0.5mg/kg (low dose) and 1.0mg/kg (high dose) body weight of ...

  12. A review of dry ports

    OpenAIRE

    Violeta Roso; Kent Lumsden

    2010-01-01

    The objective of this article is to present the previous research on the dry port concept and to review the world's existing dry ports, that is freight terminals that use the term ‘dry port’ in their name. Therefore, the purpose of this article is to clarify the concept by showing potential discrepancies or agreements between theory and practice. Starting from a literature review on the dry port concept, this article presents a review of existing dry ports in the world. A number of qualitativ...

  13. Drying and decontamination of pistachios with sequential infrared drying, tempering and hot air drying

    Science.gov (United States)

    The pistachio industry is in need of improved drying technology as the current hot air drying has low energy efficiency and drying rate and high labor cost and also does not produce safe products against microbial contamination. In the current study, dehulled and water- sorted pistachios with a mois...

  14. Effect of paddy drying depth using open-sun drying on drying time ...

    African Journals Online (AJOL)

    The smallholder rice farmers in the Uganda dry their paddy using open-sun drying method. In most cases the paddy is badly dried and has very high fissure levels. Such paddy on milling contributes to low levels of mill recovery and whole grain in the milled rice. This study was therefore done to find a recommendable ...

  15. Weight Loss Surgery

    Science.gov (United States)

    Weight loss surgery helps people with extreme obesity to lose weight. It may be an option if you cannot lose weight ... obesity. There are different types of weight loss surgery. They often limit the amount of food you ...

  16. VARIABILITY PROMISING LINES PEANUT ON THE DRY LAND IN CENTRAL MALUKU DISTRICT

    Directory of Open Access Journals (Sweden)

    Sheny Kaihatu

    2013-01-01

    Full Text Available Study multiple strains or varieties of peanut aim to get two until three peanut promising lines (productivity larger three tons per ha of drought-tolerant Series of Dry Days larger than 15 percent and adaptive dryland agroecosystem in Maluku, performed in Central Maluku district Makariki 2010, using Randomized Block Design three replications. 10 strains planted include: S-4, S-5, S-8, S-9, S-10, S-11, S-15, S-16, S-19, S-20, and two varieties local Lions and Red as comparison. Wide swath of 2.5 m x 3.5 m, spacing of 40 cm x 15 cm, one seed per planting hole. Parameter: number of observations crop plants, 50 percent flowering, plant height, maturity, number of pods per plant, weight of wet pods per plant, dry weight of pods per plant, pod dry weight per plot, weight of 100 seeds (g and dry seed weight (tons per ha. Results: strains or varieties S-4 gives a wet pod weight and dry weight of pods per plant higher in amount of 62.2 g and 37.27 g where as strain S-5, S-11, and S-15 dry seed weight higher respectively by two tons per ha.

  17. Key composition optimization of meat processed protein source by vacuum freeze-drying technology

    Directory of Open Access Journals (Sweden)

    Yan Ma

    2018-05-01

    Full Text Available Vacuum freeze-drying technology is a high technology content, a wide range of knowledge of technology in the field of drying technology is involved, it is also a method of the most complex drying equipment, the largest energy consumption, the highest cost of drying method, but due to the particularity of its dry goods: the freeze-drying food has the advantages of complex water performance is good, cooler and luster of freezing and drying food to maintain good products, less nutrient loss, light weight, easy to carry transportation, easy to long-term preservation, and on the quality is far superior to the obvious advantages of other dried food, making it become the forefront of drying technology research and development. The freeze-drying process of Chinese style ham and western Germany fruit tree tenderloin is studied in this paper, their eutectic point, melting point and collapse temperature, freeze-drying curve and its heat and mass transfer characteristics are got, then the precool temperature and the highest limiting temperature of sublimation interface are determined. The effect of system pressure on freeze-dried rate in freeze-drying process is discussed, and the method of regulating pressure circularly is determined. Keywords: Ham, Tenderloin, Vacuum freeze-dry, Processing, Optimization

  18. Estimated Bioaccessibility to 5-hydroxymethylfurfural from Frequently Consumed Dried Fruits in Iran

    Directory of Open Access Journals (Sweden)

    Nooshin Rahimzadeh

    2014-08-01

    Full Text Available We sought to determine levels of oral bioaccessibility of hydroxymethylfurfural (HMF from frequently consumed dried fruits in Iran. Fifty samples from frequently consumed types of dried fruits were analyzed for moisture, acidity and HMF content before and after in vitro digestion. Besides, bioaccessibility of HMF in dried fruits using an in vitro gastrointestinal digestive model and HMF intake from dried fruits based on consumption of each dried fruit groups wasdetermined. The mean estimated intake of HMF was 72.90 mg/kg and the maximum intake was 240.23 mg/kg for fruit bread. The mean bioaccessibility was 60.26%. There was a correlation between HMF and acid content of fruit bread (r= 0.98, P<0.05. In conclusion, the HMF levels in dried fruits remains high even after the in vitro digestion.

  19. Half-life determination for 27Mg

    Science.gov (United States)

    Zahn, G. S.; Genezini, F. A.

    2015-07-01

    In this work, the half-life of the short-lived magnesium radionuclide 27Mg was measured by following the activity of samples after they were irradiated in the IEA-R1 reactor. An exponential decay function was then fitted to the results using the counts from a 60Co source as livetime chronometer; the individual half-life values obtained for each irradiation were compiled using both the usual unweighted and σ-2-weighted averages, as well as the robust averages obtained using the Normalized Residuals and the Rajeval techniques. The final halflive values obtained aren't compatible with the ENSDF compilation values, but have a similar uncertainty; analysis of the experimental literature values, all from the 50’s-60’s, show that further measurements should be undertaken in order to achieve a more robust consensus value for this half-life.

  20. Maintenance of lettuce seed viability and counter-action of radiation damage by moisture equilibration-drying treatment

    International Nuclear Information System (INIS)

    Punjabi, Bina; Basu, R.N.

    1982-01-01

    Lettuce seeds were subjected to X- and gamma-radiation after moisture equilibration-drying or they were equilibrated with a saturated atmosphere for 24 hrs immediately after irradiation followed by drying back to the original weight. Results showed that moisture-equilibration drying treatment either before or after irradiation counteracts the adverse effects of irradiation. (M.G.B.)

  1. Maintenance of lettuce seed viability and counter-action of radiation damage by moisture equilibration-drying treatment

    Energy Technology Data Exchange (ETDEWEB)

    Punjabi, B; Basu, R N

    1982-10-01

    Lettuce seeds were subjected to X- and gamma-radiation after moisture equilibration-drying or they were equilibrated with a saturated atmosphere for 24 hrs immediately after irradiation followed by drying back to the original weight. Results showed that moisture-equilibration drying treatment either before or after irradiation counteracts the adverse effects of irradiation. (M.G.B.). 14 refs.

  2. Sibutramine in weight control: a dose-ranging, efficacy study.

    Science.gov (United States)

    Weintraub, M; Rubio, A; Golik, A; Byrne, L; Scheinbaum, M L

    1991-09-01

    We tested the safety and efficacy of sibutramine, 5 and 20 mg, and placebo on weight loss. Medication was added to caloric restriction, behavior modification, and exercise in a parallel-group, double-blind clinical trial. Participants were 130% to 180% of ideal body weight and in good health. The study lasted 12 weeks over Thanksgiving, Christmas, and New Year's Day. Weight loss during 8 weeks of study medication was: placebo, 1.4 +/- 2.1 kg (n = 19); 5 mg sibutramine, 2.9 +/- 2.3 kg (n = 18); and 20 mg sibutramine, 5.0 +/- 2.7 kg (n = 18) (p less than 0.05 sibutramine, 5 and 20 mg, versus placebo; p less than 0.05 sibutramine, 20 mg versus 5 mg). There is a significant dose-effect relationship. Five participants left the study before completion, all because of adverse events; placebo (one patient), 5 mg sibutramine (one patient), and 20 mg sibutramine (three patients). Sleep difficulties were noted by eight participants (20 mg sibutramine, seven patients; 5 mg, one patient; and placebo, no patients). Six of 21 participants receiving 20 mg complained of irritability, unusual impatience, or "excitation." Sibutramine, 5 and 20 mg, added to a multimodal program assisted participants in losing weight.

  3. Influence of drying method on steviol glycosides and antioxidants in Stevia rebaudiana leaves.

    Science.gov (United States)

    Periche, Angela; Castelló, María Luisa; Heredia, Ana; Escriche, Isabel

    2015-04-01

    The application of different drying conditions (hot air drying at 100 °C and 180 °C, freeze drying and shade drying) on steviol glycosides (stevioside, dulcoside A, rebaudioside A and rebaudioside C) and antioxidants in Stevia leaves was evaluated. Stevioside, the major glycoside found in fresh leaves (81.2mg/g), suffered an important reduction in all cases, although shade drying was the least aggressive treatment. Considering the antioxidant parameters (total phenols, flavonoids and total antioxidants), the most suitable drying method was hot air at 180 °C, since it substantially increased all of them (76.8 mg gallic acid, 45.1mg catechin and 126 mg Trolox, all equivalent/g Stevia, respectively), with respect to those present in fresh leaves (44.4, 2.5 and 52.9 mg equivalent/g). Therefore, the ideal method for drying Stevia leaves depends on their final use (sweetener or antioxidant), although, hot air at 180 °C is the most recommendable if only one treatment has to be chosen. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Evaluation of Genotoxicity and 28-day Oral Dose Toxicity on Freeze-dried Powder of Tenebrio molitor Larvae (Yellow Mealworm).

    Science.gov (United States)

    Han, So-Ri; Yun, Eun-Young; Kim, Ji-Young; Hwang, Jae Sam; Jeong, Eun Ju; Moon, Kyoung-Sik

    2014-06-01

    The larval form of Tenebrio molitor (T. molitor) has been eaten in many countries and provides benefits as a new food source of protein for humans. However, no information exists regarding its safety for humans. The objective of the present study was to evaluate the genotoxicity and repeated dose oral toxicity of the freeze-dried powder of T. molitor larvae. The genotoxic potential was evaluated by a standard battery testing: bacterial reverse mutation test, in vitro chromosome aberration test, and in vivo micronucleus test. To assess the repeated dose toxicity, the powder was administered once daily by oral gavage to Sprague-Dawley (SD) rats at dose levels of 0, 300, 1000 and 3000 mg/kg/day for 28 days. The parameters which were applied to the study were mortality, clinical signs, body and organ weights, food consumption, ophthalmology, urinalysis, hematology, serum chemistry, gross findings and histopathologic examination. The freezedried powder of T. molitor larvae was not mutagenic or clastogenic based on results of in vitro and in vivo genotoxicity assays. Furthermore, no treatment-related changes or findings were observed in any parameters in rats after 28 days oral administration. In conclusion, the freeze-dried powder of T. molitor larvae was considered to be non-genotoxic and the NOAEL (No Observed Adverse Effect Level) was determined to be 3000 mg/kg/day in both sexes of SD rats under our experimental conditions.

  5. Evaluation of Genotoxicity and 28-day Oral Dose Toxicity on Freeze-dried Powder of Tenebrio molitor Larvae (Yellow Mealworm)

    Science.gov (United States)

    Han, So-Ri; Yun, Eun-Young; Kim, Ji-Young; Hwang, Jae Sam; Jeong, Eun Ju

    2014-01-01

    The larval form of Tenebrio molitor (T. molitor) has been eaten in many countries and provides benefits as a new food source of protein for humans. However, no information exists regarding its safety for humans. The objective of the present study was to evaluate the genotoxicity and repeated dose oral toxicity of the freeze-dried powder of T. molitor larvae. The genotoxic potential was evaluated by a standard battery testing: bacterial reverse mutation test, in vitro chromosome aberration test, and in vivo micronucleus test. To assess the repeated dose toxicity, the powder was administered once daily by oral gavage to Sprague-Dawley (SD) rats at dose levels of 0, 300, 1000 and 3000 mg/kg/day for 28 days. The parameters which were applied to the study were mortality, clinical signs, body and organ weights, food consumption, ophthalmology, urinalysis, hematology, serum chemistry, gross findings and histopathologic examination. The freezedried powder of T. molitor larvae was not mutagenic or clastogenic based on results of in vitro and in vivo genotoxicity assays. Furthermore, no treatment-related changes or findings were observed in any parameters in rats after 28 days oral administration. In conclusion, the freeze-dried powder of T. molitor larvae was considered to be non-genotoxic and the NOAEL (No Observed Adverse Effect Level) was determined to be 3000 mg/kg/day in both sexes of SD rats under our experimental conditions. PMID:25071922

  6. Corrosion behaviour of Mg-Cu and Mg-Mo composites in 3.5% NaCl

    International Nuclear Information System (INIS)

    Budruk Abhijeet, S.; Balasubramaniam, R.; Gupta, M.

    2008-01-01

    The corrosion behaviour of pure magnesium, Mg-Cu (0.3, 0.6, and 1 vol.%) and Mg-Mo (0.1, 0.3, and 0.6 vol.%) composites has been studied in 3.5% NaCl solution by weight loss and polarisation methods. Corrosion rates determined by weight loss method were considerably higher than that determined by polarisation method. The corrosion rate increased with increasing volume fraction of reinforcement in Mg-Cu and Mg-Mo composites. At the same volume fraction of reinforcement, molybdenum reinforced composite corroded faster than copper reinforced composite. The galvanic current density between Mg-Cu and Mg-Mo couples has been experimentally measured using zero resistance ammeter technique. The experimentally observed galvanic current densities were in close agreement with those obtained using mixed potential theory analysis. SEM observation of corroded samples confirmed microgalvanic activity at the matrix/reinforcement interfaces. The poor corrosion resistance of composites has been attributed to microgalvanic effects between the matrix and reinforcements and inferior quality of surface films

  7. Successful Treatment of Dry Mouth and Dry Eye Symptoms in Sjögren's Syndrome Patients With Oral Pilocarpine: A Randomized, Placebo-Controlled, Dose-Adjustment Study.

    Science.gov (United States)

    Papas, Athena S; Sherrer, Yvonne S; Charney, Michael; Golden, Harvey E; Medsger, Thomas A; Walsh, Bridget T; Trivedi, Madhu; Goldlust, Barry; Gallagher, Susan C

    2004-08-01

    : Sjögren's syndrome is characterized by the presence of xerostomia and/or xerophthalmia. Pilocarpine, a muscarinic cholinergic agonist, has been proven to be efficacious in treating radiation-induced xerostomia (up to 30 mg/day) and symptoms of dry mouth in Sjögren's patients (up to 20 mg/day). : To compare the safety and efficacy of oral pilocarpine (dose-adjusted) versus placebo in the treatment of dry eye and dry mouth symptoms in Sjögren's syndrome at 6 and 12 weeks. : In this 11-center, 256-patient placebo-controlled study, the safety and efficacy of oral pilocarpine (20 mg to 30 mg daily) for relief of Sjögren's-related dry mouth and dry eye symptoms was assessed. Changes in symptoms and salivary flow were measured over 12 weeks. : Compared with placebo, salivary flow was significantly increased in the pilocarpine group (Pdry mouth (Poral symptoms (Pdry eyes (Pdry mouth symptoms was noted at 20 mg/day, and significant relief in ocular symptoms, including lower artificial tear requirement, was noted after the dose was increased to 30 mg/day.

  8. Design of solar drying-plant for bulk material drying

    Directory of Open Access Journals (Sweden)

    Peter Horbaj

    2008-11-01

    Full Text Available A generally well-known high energy requirement for technological processes of drying and the fact that the world’s supplyof the conventional energy sources has considerably decreased are the decisive factors forcing us to look for some new, if possible,renewable energy sources for this process by emphasising their environmental reliability. One of the possibilities how to replace, atleast partly, the conventional energy sources – heat in a drying process is solar energy.Air-drying of bulk materials usually has a series of disadvantages such as time expenditure, drying defects in the bulk materialand inadequate final moisture content. A method that obviates or reduces the disadvantages of air-drying and, at the same time, reducesthe costs of kiln drying, is drying with solar heat. Solar energy can replace a large part of this depletable energy since solar energy cansupply heat at the temperatures most often used to dry bulk material. Solar drying-plant offer an attractive solution.

  9. Drying of carrots in slices with osmotic dehydration

    African Journals Online (AJOL)

    SAM

    2014-07-23

    Jul 23, 2014 ... extend the shelf-life by a few weeks, one year or more. The methods .... drated carrots, this work studied the drying of carrot with pre-osmotic ... e) Weight Loss - obtained directly using balance semi-analytical model BEL ...

  10. Forage selection and performance of sheep grazing dry annual range.

    NARCIS (Netherlands)

    Ridder, de N.; Benjamin, R.W.; Keulen, van H.

    1986-01-01

    During 114 days of grazing, sheep grazing a dry annual pasture in Israel selected the fine fraction available with a higher nutritive value. As this fraction became depleted and feed quality dropped, organic matter intake dropped from 1.73 to 0.75 kg/sheep/d. Sheep lost weight, body condition and

  11. Characterization of spray dried bioadhesive metformin microparticles for oromucosal administration

    DEFF Research Database (Denmark)

    Sander, Camilla; Madsen, Katrine Dragsbæk; Hyrup, Birgitte

    2013-01-01

    delivery systems are considered a promising approach as they facilitate a close contact between the drug and the oral mucosa. In this study, bioadhesive chitosan-based microparticles of metformin hydrochloride were prepared by spray drying aqueous dispersions with different chitosan:metformin ratios...... be prepared and analyzed using the ex vivo retention model. We observed an increase in metformin retention on porcine mucosa with increasing chitosan:metformin ratios, while no effect of increasing the chitosan molecular weight was found. Rheological characterization of feeds for spray drying was performed...... and chitosan grades with increasing molecular weights. A recently developed ex vivo flow retention model with porcine buccal mucosa was used to evaluate the bioadhesive properties of spray dried microparticles. An important outcome of this study was that microparticles with the desired metformin content could...

  12. Influence of Freeze-Drying and Oven-Drying Post Blanching on the Nutrient Composition of the Edible Insect Ruspolia differens.

    Science.gov (United States)

    Fombong, Forkwa Tengweh; Van Der Borght, Mik; Vanden Broeck, Jozef

    2017-09-16

    The longhorn grasshopper, Ruspolia differens (Serville), plays an important role as a food source across Sub-Saharan Africa, where it is consumed as a delicacy in both rural and urban areas. The effect of two drying methods (freeze-drying and oven-drying), employed after blanching, on the proximate, fatty acid and mineral composition of the two most common morphs was determined. Ruspolia differens grasshoppers were harvested in Uganda and Kenya from wild swarms during the rainy periods of November-December 2016. Based on cuticular coloration, we identified three morphs, green, brown and purple, which occurred at a ratio of 65:33:2, respectively. Results indicated that these insects have a high lipid content of 36%, as well as significant protein levels ranging between 33% and 46% dry matter. Oleic acid (44%) and palmitic acid (28%) were the two most abundant fatty acids; while the presence of arachidonic acid (0.6%) and docosahexaenoic acid (0.21%) suggests that Ruspolia differens is also a source of polyunsaturated fatty acids. The observed amino acid profile showed similar trends in all morphs, and all essential amino acids were present. Calcium (896-1035 mg/100 g), potassium (779-816 mg/100 g) and phosphorus (652-685 mg/100 g) were quite high among the minerals. The presence of the trace elements iron (217-220 mg/100 g), zinc (14.2-14.6 mg/100 g), manganese (7.4-8.3 mg/100 g) and copper (1.66 mg/100 g) suggests that inclusion of these grasshoppers in human diets may aid in combatting micronutrient deficiencies. Oven-drying Ruspolia differens delivered the same nutritional quality as freeze-drying. Hence, both drying approaches can be adequately used to formulate insect-based food products without noticeable nutritional changes.

  13. Influence of Freeze-Drying and Oven-Drying Post Blanching on the Nutrient Composition of the Edible Insect Ruspolia differens

    Directory of Open Access Journals (Sweden)

    Forkwa Tengweh Fombong

    2017-09-01

    Full Text Available The longhorn grasshopper, Ruspolia differens (Serville, plays an important role as a food source across Sub-Saharan Africa, where it is consumed as a delicacy in both rural and urban areas. The effect of two drying methods (freeze-drying and oven-drying, employed after blanching, on the proximate, fatty acid and mineral composition of the two most common morphs was determined. Ruspolia differens grasshoppers were harvested in Uganda and Kenya from wild swarms during the rainy periods of November–December 2016. Based on cuticular coloration, we identified three morphs, green, brown and purple, which occurred at a ratio of 65:33:2, respectively. Results indicated that these insects have a high lipid content of 36%, as well as significant protein levels ranging between 33% and 46% dry matter. Oleic acid (44% and palmitic acid (28% were the two most abundant fatty acids; while the presence of arachidonic acid (0.6% and docosahexaenoic acid (0.21% suggests that Ruspolia differens is also a source of polyunsaturated fatty acids. The observed amino acid profile showed similar trends in all morphs, and all essential amino acids were present. Calcium (896–1035 mg/100 g, potassium (779–816 mg/100 g and phosphorus (652–685 mg/100 g were quite high among the minerals. The presence of the trace elements iron (217–220 mg/100 g, zinc (14.2–14.6 mg/100 g, manganese (7.4–8.3 mg/100 g and copper (1.66 mg/100 g suggests that inclusion of these grasshoppers in human diets may aid in combatting micronutrient deficiencies. Oven-drying Ruspolia differens delivered the same nutritional quality as freeze-drying. Hence, both drying approaches can be adequately used to formulate insect-based food products without noticeable nutritional changes.

  14. Comparison of drying characteristic and uniformity of banana cubes dried by pulse-spouted microwave vacuum drying, freeze drying and microwave freeze drying.

    Science.gov (United States)

    Jiang, Hao; Zhang, Min; Mujumdar, Arun S; Lim, Rui-Xin

    2014-07-01

    To overcome the flaws of high energy consumption of freeze drying (FD) and the non-uniform drying of microwave freeze drying (MFD), pulse-spouted microwave vacuum drying (PSMVD) was developed. The results showed that the drying time can be dramatically shortened if microwave was used as the heating source. In this experiment, both MFD and PSMVD could shorten drying time by 50% as compared to the FD process. Depending on the heating method, MFD and PSMVD dried banana cubes showed trends of expansion while FD dried samples demonstrated trends of shrinkage. Shrinkage also brought intensive structure and highest fracturability of all three samples dried by different methods. The residual ascorbic acid content of PSMVD dried samples can be as high as in FD dried samples, which were superior to MFD dried samples. The tests confirmed that PSMVD could bring about better drying uniformity than MFD. Besides, compared with traditional MFD, PSMVD can provide better extrinsic feature, and can bring about improved nutritional features because of the higher residual ascorbic acid content. © 2013 Society of Chemical Industry.

  15. Neuropathic pain and dry eye.

    Science.gov (United States)

    Galor, Anat; Moein, Hamid-Reza; Lee, Charity; Rodriguez, Adriana; Felix, Elizabeth R; Sarantopoulos, Konstantinos D; Levitt, Roy C

    2018-01-01

    Dry eye is a common, multifactorial disease currently diagnosed by a combination of symptoms and signs. Its epidemiology and clinical presentation have many similarities with neuropathic pain outside the eye. This review highlights the similarities between dry eye and neuropathic pain, focusing on clinical features, somatosensory function, and underlying pathophysiology. Implications of these similarities on the diagnosis and treatment of dry eye are discussed. Published by Elsevier Inc.

  16. Solar drying of West Indian ginger (Zingiber officinale Roscoe) rhizome using a wire basket dryer

    Energy Technology Data Exchange (ETDEWEB)

    Balladin, D.A.; Headley, O. [University of the West Indies (Barbados). Dept. of Chemistry; Chang Yen, I. [University of the West Indies, St. Augustine (Trinidad and Tobago). Dept. of Chemistry; McGaw, D.R. [University of the West Indies, St. Augustine (Trinidad and Tobago). Dept. of Chemical Engineering

    1996-09-01

    A wire basket dryer (1.8 m x 0.9 m x 0.2 m) was used to dry sliced (0.15 cm) West Indian ginger (Zingiber officinale Roscoe) rhizome to an acceptable moisture content of 10.2% (dry weight basis) over a 3 day period. The optimum charge size was 14.97 kg, with a packing density of 462.04 kg m{sup -3} and a specific drying rate of 0.446 h{sup -1}. The quantities (determined by high-pressure liquid chromatography) of the main pungent principles (ginerol and shogaol) extracted from fresh, non-steam-distilled solar-dried and steam-distilled solar-dried ginger rhizomes showed increases of 0.068, 0.46 and 0.67 g [per 100 g (dry weight basis)], respectively, with a decrease in the oleoresin quality (reflected in pungency profile) of the same order. (author)

  17. Key composition optimization of meat processed protein source by vacuum freeze-drying technology.

    Science.gov (United States)

    Ma, Yan; Wu, Xingzhuang; Zhang, Qi; Giovanni, Vigna; Meng, Xianjun

    2018-05-01

    Vacuum freeze-drying technology is a high technology content, a wide range of knowledge of technology in the field of drying technology is involved, it is also a method of the most complex drying equipment, the largest energy consumption, the highest cost of drying method, but due to the particularity of its dry goods: the freeze-drying food has the advantages of complex water performance is good, cooler and luster of freezing and drying food to maintain good products, less nutrient loss, light weight, easy to carry transportation, easy to long-term preservation, and on the quality is far superior to the obvious advantages of other dried food, making it become the forefront of drying technology research and development. The freeze-drying process of Chinese style ham and western Germany fruit tree tenderloin is studied in this paper, their eutectic point, melting point and collapse temperature, freeze-drying curve and its heat and mass transfer characteristics are got, then the precool temperature and the highest limiting temperature of sublimation interface are determined. The effect of system pressure on freeze-dried rate in freeze-drying process is discussed, and the method of regulating pressure circularly is determined.

  18. Mindfulness Approaches and Weight Loss, Weight Maintenance, and Weight Regain.

    Science.gov (United States)

    Dunn, Carolyn; Haubenreiser, Megan; Johnson, Madison; Nordby, Kelly; Aggarwal, Surabhi; Myer, Sarah; Thomas, Cathy

    2018-03-01

    There is an urgent need for effective weight management techniques, as more than one third of US adults are overweight or obese. Recommendations for weight loss include a combination of reducing caloric intake, increasing physical activity, and behavior modification. Behavior modification includes mindful eating or eating with awareness. The purpose of this review was to summarize the literature and examine the impact of mindful eating on weight management. The practice of mindful eating has been applied to the reduction of food cravings, portion control, body mass index, and body weight. Past reviews evaluating the relationship between mindfulness and weight management did not focus on change in mindful eating as the primary outcome or mindful eating as a measured variable. This review demonstrates strong support for inclusion of mindful eating as a component of weight management programs and may provide substantial benefit to the treatment of overweight and obesity.

  19. Post-LASIK dry eye

    Science.gov (United States)

    Shtein, Roni M

    2011-01-01

    Laser-assisted in situ keratomileusis (LASIK) is a frequently performed corneal refractive surgery with excellent refractive outcomes. The most common complication of LASIK is dry eyes, with virtually all patients developing some degree of dryness in the immediate postoperative period. Identifying preoperative dry eyes, and conscientious attention and treatment in the perioperative time period, can lead to enhanced patient satisfaction and more accurate visual outcomes. Improved understanding of the development of dry eyes after LASIK will advance our understanding of the complex pathophysiology of dry eye disease. PMID:22174730

  20. Quality of dry chemistry testing.

    Science.gov (United States)

    Nakamura, H; Tatsumi, N

    1999-01-01

    Since the development of the qualitative test paper for urine in 1950s, several kinds of dry-state-reagents and their automated analyzers have been developed. "Dry chemistry" has become to be called since the report on the development of quantitative test paper for serum bilirubin with reflectometer in the end of 1960s and dry chemistry has been world widely known since the presentation on the development of multilayer film reagent for serum biochemical analytes by Eastman Kodak Co at the 10th IFCC Meeting in the end of 1970s. We have reported test menu, results in external quality assessment, merits and demerits, and the future possibilities of dry chemistry.

  1. MgB2 and Mg1-xAlxB2 single crystals: high pressure growth and physical properties

    International Nuclear Information System (INIS)

    Karpinski, J.; Kazakov, S.M.; Jun, J.; Zhigadlo, N.D.; Angst, M.; Puzniak, R.; Wisniewski, A.

    2004-01-01

    Single crystals of MgB 2 have been grown with a high pressure cubic anvil technique. They grow via the peritectic decomposition of the MgNB 9 ternary nitride. The crystals are of a size up to 2 x 1 x 0.1 mm 3 with a weight up to 230 μg. Typically they have transition temperatures between 38 and 38.6 K with a width of 0.3-0.5 K. Investigations of the P-T phase diagram prove that the MgB 2 phase is stable at least up to 2190 deg. C at high hydrostatic pressure in the presence of Mg vapor under high pressure. Substitution of aluminum for magnesium in single crystals leads to stepwise decrease of T c . This indicates a possible appearance of superstructures or phases with different T c 's. The upper critical field decreases with Al doping

  2. Comparison of Different Drying Methods for Recovery of Mushroom DNA.

    Science.gov (United States)

    Wang, Shouxian; Liu, Yu; Xu, Jianping

    2017-06-07

    Several methods have been reported for drying mushroom specimens for population genetic, taxonomic, and phylogenetic studies. However, most methods have not been directly compared for their effectiveness in preserving mushroom DNA. In this study, we compared silica gel drying at ambient temperature and oven drying at seven different temperatures. Two mushroom species representing two types of fruiting bodies were examined: the fleshy button mushroom Agaricus bisporus and the leathery shelf fungus Trametes versicolor. For each species dried with the eight methods, we assessed the mushroom water loss rate, the quality and quantity of extracted DNA, and the effectiveness of using the extracted DNA as a template for PCR amplification of two DNA fragments (ITS and a single copy gene). Dried specimens from all tested methods yielded sufficient DNA for PCR amplification of the two genes in both species. However, differences among the methods for the two species were found in: (i) the time required by different drying methods for the fresh mushroom tissue to reach a stable weight; and (ii) the relative quality and quantity of the extracted genomic DNA. Among these methods, oven drying at 70 °C for 3-4 h seemed the most efficient for preserving field mushroom samples for subsequent molecular work.

  3. CO_2 capture in Mg oxides doped with Fe and Ni

    International Nuclear Information System (INIS)

    Sanchez S, I. F.

    2016-01-01

    In this work the CO_2 capture-desorption characteristics in Mg oxides doped with Fe and Ni obtained by the direct oxidation of Mg-Ni and Mg-Fe mixtures are presented. Mixtures of Mg-Ni and Mg-Fe in a different composition were obtained by mechanical milling in a Spex-type mill in a controlled atmosphere of ultra high purity argon at a weight / weight ratio of 4:1 powder using methanol as a lubricating agent, for 20 h. The powders obtained by mechanical milling showed as main phase, the Mg with nanocrystalline structure. Subsequently, the mixtures of Mg-Ni and Mg-Fe were oxidized within a muffle for 10 min at 600 degrees Celsius. By means of X-ray diffraction analysis, the Mg O with nano metric grain size was identified as the main phase, which was determined by the Scherrer equation. In the Mg O doped with Ni, was identified that as the Ni amount 1 to 5% by weight dispersed in the Mg O matrix was increased, the main peak intensity of the Ni phase increased, whereas in the Mg O doped with Fe was observed by XRD, that the Fe_2O_3 phase was present and by increasing the amount of Fe (1 to 5% by weight) dispersed in the crystalline phase of Mg O, the intensity of this impurity also increased. Sem-EDS analysis showed that the Ni and Fe particles are dispersed homogeneously in the Mg O matrix, and the particles are porous, forming agglomerates. Through energy dispersive spectroscopy analysis, the elemental chemical composition obtained is very close to the theoretical composition. The capture of CO_2 in the Mg O-1% Ni was carried out in a Parr reactor at different conditions of pressure, temperature and reaction time. Was determined that under the pressure of 0.2 MPa at 26 degrees Celsius for 1 h of reaction, the highest CO_2 capture of 7.04% by weight was obtained, while in Mg O-1% Fe the CO_2 capture was 6.32% by weight. The other magnesium oxides doped in 2.5 and 5% by weight Ni and Fe showed lower CO_2 capture. The different stages of mass loss and thermal

  4. a comparative study of the drying rate constant, drying efficiency

    African Journals Online (AJOL)

    The drying rate constants for the solar dryer and open- air sun dried bitter leaf were 0.8 and ... of cost benefit but the poorest when other considerations ... J. I. Eze, National Centre for Energy Research and Development (NCERD), University of ...

  5. Carrageenan drying with dehumidified air: drying characteristics and product quality

    NARCIS (Netherlands)

    Djaeni, M.; Sasongko, S.B.; Prasetyaningrum, Aji A A.A.; Jin, X.; Boxtel, van A.J.B.

    2012-01-01

    Applying dehumidified air is considered as an option to retain quality in carrageenan drying. This work concerns the effects of operational temperature, air velocity, and carrageenan thickness on the progress of drying and product quality when using dehumidified air. Final product quality and

  6. The antisickling effects of dried fish (tilapia) And dried prawn ...

    African Journals Online (AJOL)

    The antisickling effect of dried fish (Tilapia) and dried prawn (Astacus red) were investigated to ascertain the ability of the extracts of these samples to inhibit polymerisation of sickle cell haemoglobin (HbS), improve the Fe 2+/Fe 3+ ratio and lower the activity of lactate dehydrogenase (LDH) in blood plasma. The samples ...

  7. Optimization of frozen wild blueberry vacuum drying process

    Directory of Open Access Journals (Sweden)

    Šumić Zdravko M.

    2015-01-01

    Full Text Available The objective of this research was to optimize the vacuum drying of frozen blueberries in order to preserve health benefits phytochemicals using response surface methodology. The drying was performed in a new design of vacuum dryer equipment. Investigated range of temperature was 46-74°C and of pressure 38-464 mbar. Total solids, total phenolics, vitamin C, anthocyanin content and total color change were used as quality indicators of dried blueberries. Within the experimental range of studied variables, the optimum conditions of 60 °C and 100 mbar were established for vacuum drying of blueberries. Separate validation experiments were conducted at optimum conditions to verify predictions and adequacy of the second-order polynomial models. Under these optimal conditions, the predicted amount of total phenolics was 3.70 mgCAE/100dw, vitamin C 59.79 mg/100gdw, anthocyanin content 2746.33 mg/100gdw, total solids 89.50% and total color change 88.83. [Projekat Ministarstva nauke Republike Srbije, br. TR 31044

  8. Spray Drying of High Sugar Content Foods: Improving of Product Yield and Powder Properties

    OpenAIRE

    Mehmet Koç; Figen Kaymak-Ertekin

    2016-01-01

    Spray drying is the most preferred drying method to produce powdered food in the food industry and it is also widely used to convert sugar-rich liquid foods to a powder form. During and/or after spray drying process of sugar-rich products, undesirable situation was appeared such as stickiness, high moisture affinity (hygroscopicity) and low solubility due to low molecular weight monosaccharides that found naturally in the structure. The basis of these problems was formed by low glass transiti...

  9. Generalized drying curves in conductive/convective paper drying

    Directory of Open Access Journals (Sweden)

    O.C. Motta Lima

    2000-12-01

    Full Text Available This work presents a study related to conductive/convective drying of paper (cellulose sheets over heated surfaces, under natural and forced air conditions. The experimental apparatus consists in a metallic box heated by a thermostatic bath containing an upper surface on which the paper samples (about 1 mm thick are placed. The system is submitted to ambient air under two different conditions: natural convection and forced convection provide by an adjustable blower. The influence of initial paper moisture content, drying (heated surface temperature and air velocity on drying curves behavior is observed under different drying conditions. Hence, these influence is studied through the proposal of generalized drying curves. Those curves are analyzed individually for each air condition exposed above and for both together. A set of equations to fit them is proposed and discussed.

  10. Effects of composite surface coating and pre-drying on the properties of kabanosy dry sausage.

    Science.gov (United States)

    Tyburcy, Andrzej; Kozyra, Daniel

    2010-10-01

    Coating of dry sausages with renewable materials could be an alternative to vacuum packaging. In this study kabanosy dry sausage was coated with a composite emulsion and stored for 7 or 15 days at 4-6 degrees C. Effects of different emulsion formulas (0.5 or 1% w/w of kappa-carrageenan and 5 or 10% w/w of glycerol) and pre-drying of coated sausages (at 50 degrees C for 1.5h) were investigated. Carrageenan concentration had a significant effect (Pemulsion adsorbed on the sausage surface but little influence on the barrier properties of the coatings. At both glycerol concentration levels, coatings had no visible cracks and were easily removed from the sausage surface after 7 and 15 days of storage. The colour values of coatings (L*, a*, and b*) changed along with the decreasing water activity during storage. Pre-drying of coated sausages reduced peeled product weight loss after storage. The financial analysis showed that among coatings tested the best proved to be the emulsion containing (w/w): 5% glycerol, 5% gelatin, 0.5% carrageenan, 20% lard, 20% beeswax, and 50% water. Copyright (c) 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

  11. Market opportunities for solar drying

    International Nuclear Information System (INIS)

    Voskens, R.G.J.H.; Out, P.G.; Schulte, B.

    2000-01-01

    One of the most promising applications for solar heating is the drying of agricultural products. The drying of agricultural products requires large quantities of low temperature air, in many cases, on a year-round basis. Low cost air-based collectors can provide heated air at solar collection efficiencies of 30 to 70%. In 1998/1999 a study was commissioned to better understand the technical and economic potential for solar drying of agricultural products in the world. The practical potential for solar drying was then determined for 59 crops and 22 regions. The world market for solar drying can be divided into three market segments: 1) mechanical drying T 50 deg. C; 3) sun drying. The most promising market for solar drying is generally market segment 1. For this segment the potential amount of energy displaced by solar is in between 216 770 PJ (World-wide). For Western Europe this potential is estimated between 23 88 PJ and for Eastern Europe between 7 and 13 PJ. A different market introduction strategy is required for each market segment. A total of 13 combinations of crops and regions are selected that appear to have the highest practical potential for solar drying. In the Netherlands a programme of activities was carried out by Ecofys and other organisations, to identify and develop the market potential for solar (assisted) drying of agricultural products. A promotional campaign for the use of renewable energy in the (promising) flower bulb sector is planned on a short-term basis to speed up market developments. It can be concluded that there is a large market for solar drying in the World as well as in Europe. (au)

  12. Dry wall Kras 2011

    Directory of Open Access Journals (Sweden)

    Domen Zupančič

    2012-01-01

    Full Text Available Despite the modesty of hiska, they show a simple understanding of corbelling technique. One could say they are all examples of human landscape cultivation. Although there is no evident common line when comparing all types of hiska, the cunning eye may observe one shared feature: the positioning of the entrance. More or less all the documented shelters have south or south-western facing entrances. The burja is a cold northerly wind; from the south (Adriatic Sea the winds are warmer. When resting, the setting sun is taken as a sign of the ending of the working day and a reward for the whole day’s efforts. Entrances are the only openings to these structures, and they should serve as well as possible - to watch over the crops, to wait when hunting, to enjoy the calm of evening light, to breathe the sea wind.The syntax of the architectural language of layering stone and shaping the pattern of the landscape remain an inventive realisation of spatial ideas from the past until today. Not only ideas of shaping space - these ideas are basic interventions in the natural habitat which contribute to survival. Culture and an awareness of its values are the origins of local development and reasonable heritage preservation. The next step are tutorial days with workshops on how to build dry stone structures, walls and other stone architecture, as the DSWA organisation in the UK is doing.

  13. Forward Osmosis Brine Drying

    Science.gov (United States)

    Flynn, Michael; Shaw, Hali; Hyde, Deirdre; Beeler, David; Parodi, Jurek

    2015-01-01

    The Forward Osmosis Brine Drying (FOBD) system is based on a technique called forward osmosis (FO). FO is a membrane-based process where the osmotic potential between brine and a salt solution is equalized by the movement of water from the brine to the salt solution. The FOBD system is composed of two main elements, the FO bag and the salt regeneration system. This paper discusses the results of testing of the FO bag to determine the maximum water recovery ratio that can be attained using this technology. Testing demonstrated that the FO bag is capable of achieving a maximum brine water recovery ratio of the brine of 95%. The equivalent system mass was calculated to be 95 kg for a feed similar to the concentrated brine generated on the International Space Station and 86 kg for an Exploration brine. The results have indicated that the FOBD can process all the brine for a one year mission for between 11% to 10% mass required to bring the water needed to make up for water lost in the brine if not recycled. The FOBD saves 685 kg and when treating the International Space Station brine and it saves 829 kg when treating the Exploration brine. It was also demonstrated that saturated salt solutions achieve a higher water recovery ratios than solids salts do and that lithium chloride achieved a higher water recovery ratio than sodium chloride.

  14. Wet Mars, Dry Mars

    Science.gov (United States)

    Fillingim, M. O.; Brain, D. A.; Peticolas, L. M.; Yan, D.; Fricke, K. W.; Thrall, L.

    2012-12-01

    The magnetic fields of the large terrestrial planets, Venus, Earth, and Mars, are all vastly different from each other. These differences can tell us a lot about the interior structure, interior history, and even give us clues to the atmospheric history of these planets. This poster highlights the third in a series of presentations that target school-age audiences with the overall goal of helping the audience visualize planetary magnetic field and understand how they can impact the climatic evolution of a planet. Our first presentation, "Goldilocks and the Three Planets," targeted to elementary school age audiences, focuses on the differences in the atmospheres of Venus, Earth, and Mars and the causes of the differences. The second presentation, "Lost on Mars (and Venus)," geared toward a middle school age audience, highlights the differences in the magnetic fields of these planets and what we can learn from these differences. Finally, in the third presentation, "Wet Mars, Dry Mars," targeted to high school age audiences and the focus of this poster, the emphasis is on the long term climatic affects of the presence or absence of a magnetic field using the contrasts between Earth and Mars. These presentations are given using visually engaging spherical displays in conjunction with hands-on activities and scientifically accurate 3D models of planetary magnetic fields. We will summarize the content of our presentations, discuss our lessons learned from evaluations, and show (pictures of) our hands-on activities and 3D models.

  15. Presence or absence of ocular surface inflammation directs clinical and therapeutic management of dry eye.

    Science.gov (United States)

    Sambursky, Robert

    2016-01-01

    The presence of clinically significant inflammation has been confirmed in the tears of 40%-65% of patients with symptoms of dry eye. Ocular surface inflammation may lead to tear film instability, epithelial cell irregularities, and permeability, resulting in chronic symptomatic pain and fluctuating vision as well as negative surgical outcomes. A retrospective single center medical chart review of 100 patients was conducted. All patients were tested with the InflammaDry test to determine if patients exhibited elevated levels of matrix metalloproteinase 9 (MMP-9). InflammaDry-positive patients were started on a combination of cyclosporine 0.05% twice daily, 2,000-4,000 mg oral omega-3 fatty acids, and frequent artificial tear replacement. InflammaDry-negative patients were started on 2,000-4,000 mg of oral omega-3 fatty acids and frequent artificial tear replacement. Each patient was retested at ~90 days. A symptom questionnaire was performed at the initial visit and at 90 days. 60% of the patients with dry eye symptoms tested positive for elevated MMP-9 at the initial visit. 78% of all patients returned for follow-up at ~90 days including 80% (48/60) of the previously InflammaDry-positive patients and 75% (30/40) of the previously InflammaDry-negative patients. A follow-up symptom questionnaire reported at least 75% symptomatic improvement in 65% (31/48) of the originally InflammaDry-positive patients and in 70% (21/30) of the initially InflammaDry-negative patients. Symptomatic improvement of at least 50% was reported in 85% (41/48) of previously InflammaDry-positive patients and 86% (26/30) of previously InflammaDry-negative patients. Following treatment, 54% (26/48) of previously InflammaDry-positive patients converted to a negative InflammaDry result. Identifying which symptomatic dry eye patients have underlying inflammation may predict patient responses to treatment and influence clinical management strategies.

  16. Presence of electrostatically adsorbed polysaccharides improves spray drying of liposomes.

    Science.gov (United States)

    Karadag, Ayse; Özçelik, Beraat; Sramek, Martin; Gibis, Monika; Kohlus, Reinhard; Weiss, Jochen

    2013-02-01

    Spray drying of liposomes with conventional wall materials such as maltodextrins often yields nonfunctional powders, that is, liposomes break down during drying and rehydration. Electrostatically coating the surface of liposomes with a charged polymer prior to spray drying may help solve this problem. Anionic lecithin liposomes (approximately 400 nm) were coated with lower (approximately 500 kDa, LMW-C) or higher (approximately 900 kDa, HMW-C) molecular weight cationic chitosan using the layer-by-layer depositing method. Low (DE20, LMW-MD) or high molecular weight (DE2, HMW-MD) maltodextrin was added as wall material to facilitate spray drying. If surfaces of liposomes (1%) were completely covered with chitosan (0.4%), no bridging or depletion flocculation would occur, and mean particle diameters would be approximately 500 nm. If maltodextrins (20%) were added to uncoated liposomes, extensive liposomal breakdown would occur making the system unsuitable for spray drying. No such aggregation or breakdown was observed when maltodextrin was added to chitosan-coated liposomes. Size changed little or even decreased slightly depending on the molecular weight of maltodextrin added. Scanning electron microscopy images of powders containing chitosan-coated liposomes revealed that their morphologies depended on the type of maltodextrin added. Powders prepared with LMW-MD contained mostly spherical particles while HMW-MD powders contained particles with concavities and dents. Upon redispersion, coated liposomes yielded back dispersions with particle size distributions similar to the original ones, except for LMW-C coated samples that had been spray dried with HMW-MD which yielded aggregates (approximately 30 μm). Results show that coating of liposomes with an absorbing polymer allows them to be spray dried with conventional maltodextrin wall materials. Liposomes have attracted considerable attention in the food and agricultural, biomedical industries for the delivery of

  17. Weight Gain during Pregnancy

    Science.gov (United States)

    ... Global Map Premature Birth Report Cards Careers Archives Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal ... fitness > Weight gain during pregnancy Weight gain during pregnancy E-mail to a friend Please fill in ...

  18. Should I Gain Weight?

    Science.gov (United States)

    ... Videos for Educators Search English Español Should I Gain Weight? KidsHealth / For Teens / Should I Gain Weight? ... something about it. Why Do People Want to Gain Weight? Some of the reasons people give for ...

  19. Heavy Metals (Mg, Mn, Ni and Sn contamination in Soil Samples of Ahvaz II Industrial Estate of Iran in 2013

    Directory of Open Access Journals (Sweden)

    Soheil l Sobhanardakani

    2016-04-01

    Full Text Available Background & Aims of the Study: Due to the rapid industrial development in Khuzestan province of Iran during recent years, this study was performed to analyze the variation of metals concentrations (Mg, Mn, Ni, and Sn in soil samples of Ahvaz II Industrial estate during the spring season of 2013. Materials & Methods: In this experimental study, 27 topsoil samples were collected from nine stations. The intensity of the soil contamination was evaluated, using a contamination factor (Cf and geo-accumulation index (I-geo. Results:  The mean soil concentrations (in mg kg-1 (dry weight were in ranged within 870-1144 (Mg, 188-300 (Mn, 93-199 (Ni and 9-15 (Sn. The data indicated that the I-geo value for all metals falls in class ‘1’. Also the Cf value for Mg and Mn falls in class ‘0’, the Cf value for Sn falls in class ‘1’ and the Cf value for Ni falls in the classes of ‘1’ and ‘2’. The result of the Pearson correlation showed that there were significant positive associations between all metals. Conclusions: According to the results which were achieved by a cluster analysis, there were significant positive associations among all metals based on Pearson correlation coefficient, especially between Ni and Sn; also both of them with Mn. Because the Ni originates from oil sources it can be resulted that Mn and Sn originate from oil sources, too. Therefore, industrial activities and exploitation of oil reservoirs are the main cause of pollution in that area. Also, it can be concluded that, with increasing the distance from the source of pollution, the accumulation of contaminants in the soil samples decreased.

  20. Energy cost of seed drying

    Directory of Open Access Journals (Sweden)

    Weerachet Jittanit

    2017-11-01

    Full Text Available In this work, the energy costs of drying corn, rice and wheat seeds between 3 drying options were compared. They consisted of 1 two-stage drying by using fluidised bed dryer (FBD in the 1st stage and in-store dryer (ISD in the 2nd stage, 2 single-stage drying by fixed bed dryer (FXD and 3 two-stage drying by using FXD in the 1st  stage and ISD in the 2nd  stage. The drying conditions selected for comparison were proved to be safe for seed viability by the previous studies. The results showed that the drying options 2 and 3 consumed less energy than option 1. However, the benefits from lower energy cost must be weighed against some advantages of using FBD. Furthermore, it appeared that running the burners of FXD and ISD for warming up the ambient air during humid weather condition could shorten drying time significantly with a little higher energy cost.

  1. Drying effect on flavonoid composition and antioxidant activity of immature kumquat.

    Science.gov (United States)

    Lou, Shyi-Neng; Lai, Yi-Chun; Huang, Jia-De; Ho, Chi-Tang; Ferng, Lin-Huei A; Chang, Yung-Chung

    2015-03-15

    A seven flavonoids in hot water extract of immature kumquat (Citrus japonica var. margarita) were identified and quantified (mg/100g fresh fruit): 3',5'-di-C-β-glucopyranosylphloretin (DGPP, 285.9 ± 2.9 mg/100g), acacetin 8-C-neohesperidoside (margaritene, 136.2 ± 2.6 mg/100g), acacetin 6-C-neohesperidoside (isomargaritene, 119.1 ± 1.8 mg/100g), fortunellin (acacetin 7-O-neohesperidoside, 28.5 ± 0.7 mg/100g), apigenin 8-C-neohesperidoside (16.9 ± 0.1mg/100g), poncirin (isosakuranetin 7-O-neohesperidoside, 5.1 ± 0.1mg/100g), and rhoifolin (apigenin 7-O-neohesperidoside, 2.0 ± 0.1mg/100g). When immature kumquat was dried at 110 and 130°C for 0.5h, the antioxidant activity, total phenolic content and identified flavonoids increased. The UV absorbance of browning products of immature kumquat dried at 130°C for 1.5h increased dramatically, while the identified flavonoids decreased. Therefore, it was concluded that drying below 130°C for 1.0 h, could release phenolic compounds, which resulted in the increasing antioxidant activity. Drying at 130°C for 1.5h, it might be due to the effect of formed browning products. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Dry eyes: etiology and management.

    Science.gov (United States)

    Latkany, Robert

    2008-07-01

    Until recently, the cause of dry eye syndrome was uncertain and the treatment was palliative. Since discovering that dry eyes are caused by inflammation, there has been an abundance of research focusing on anti-inflammatory therapies, other contributing causes, and better diagnostic testing. This review summarizes some of the interesting published research on ocular surface disease over the past year. The definition of dry eye now highlights the omnipresent symptom of blurry vision. The re-evaluation of ocular surface staining, tear meniscus height, and visual change will allow for a better diagnosis and understanding of dry eyes. Punctal plugs, and oral and topical anti-inflammatory use will strengthen our arsenal against ocular surface disease. Major progress has occurred in the past few years in gaining a better understanding of the etiology of dry eye syndrome, which will inevitably lead to more effective therapeutic options.

  3. Drying kinetics of atemoya pulp

    Directory of Open Access Journals (Sweden)

    Plúvia O. Galdino

    Full Text Available ABSTRACT This study was conducted in order to obtain drying curves of whole atemoya pulp through the foam-mat drying method. The suspension was prepared with whole atemoya pulp mixed with 2% of Emustab® and 2% of Super Liga Neutra® with mixing time of 20 min, and dried in a forced-air oven at different temperatures (60; 70 and 80 °C and thicknesses of the foam layer (0.5, 1.0 and 1.5 cm. The drying rate curves were plotted against the water content ratio and the semi-theoretical models of Henderson & Pabis, Page and Midilli were used. All tested models showed coefficient of determination (R2 above 0.993, and the Midilli model showed the best fit for all conditions. Drying curves were affected by temperature and layer thickness.

  4. Total arsenic, mercury, lead, and cadmium contents in edible dried seaweed in Korea.

    Science.gov (United States)

    Hwang, Y O; Park, S G; Park, G Y; Choi, S M; Kim, M Y

    2010-01-01

    Total arsenic, mercury, lead, and cadmium contents were determined in 426 samples of seaweed sold in Korea in 2007-08. The average concentrations, expressed in mg kg(-1), dry weight, were: total arsenic 17.4 (less than the limit of detection [LOD] to 88.8), Hg 0.01 (from 0.001 to 0.050), lead 0.7 (less than the LOD to 2.7), and cadmium 0.50 (less than the LOD to 2.9). There were differences in mercury, cadmium, and arsenic content in seaweed between different kinds of products and between coastal areas. The intakes of total mercury, lead, and cadmium for Korean people from seaweed were estimated to be 0.11, 0.65, and 0.45 µg kg(-1) body weight week(-1), respectively. With respect to food safety, consumption of 8.5 g day(-1) of the samples analysed could represent up to 0.2-6.7% of the respective provisional tolerable weekly intakes established by the World Health Organization (WHO). Therefore, even if Korean people have a high consumption of seaweed, this study confirms the low probability of health risks from these metals via seaweed consumption.

  5. Space and Industrial Brine Drying Technologies

    Science.gov (United States)

    Jones, Harry W.; Wisniewski, Richard S.; Flynn, Michael; Shaw, Hali

    2014-01-01

    This survey describes brine drying technologies that have been developed for use in space and industry. NASA has long considered developing a brine drying system for the International Space Station (ISS). Possible processes include conduction drying in many forms, spray drying, distillation, freezing and freeze drying, membrane filtration, and electrical processes. Commercial processes use similar technologies. Some proposed space systems combine several approaches. The current most promising candidates for use on the ISS use either conduction drying with membrane filtration or spray drying.

  6. Radiation preservation of dried fish indigenous to Asia

    International Nuclear Information System (INIS)

    Hussain, A.M.; Haz, I.; Chaudry, M.A.

    1989-01-01

    Commercially dried marine fish such as mackerel, shark, tuna and saram (Scomboromorus commersoni) contain 36-50% moisture and 10-12% salt. During preliminary studies, there was visible mould growth on sun or over dried freshwater rahu (Labeo sp.) fish containing moisture levels above 15.5%. Fusarium was present in samples containing a moisture level of 46% and above, while below this level Aspergillus sp. and Penicillium sp. were present. Dipping of fish fillets in 2% potassium sorbate checked the visible mould growth on irradiated (0.25-1 kGy) and non-irradiated rahu fish containing moisture levels of 20-40%. Radiation doses of 0.5-0.75 kGy were found suitable for keeping sun or oven dried samples in good and acceptable conditions for six months at room temperature. Polyethylene film about 0.1 mm thick was suitable for packing dried fish as far as insect penetration, bacterial permeability, water permeability, water vapour transfer rate and weight loss of dried fish during storage were concerned. An oxygen absorber was effective for six months in maintaining colour, odour and texture of irradiated dried fish packaged in an oxygen impermeable film. Dried fish was acceptable to consumers except to some extent for its texture. Bulk storage of dried fish fillets at an ambient temperature for 3 months produced no adverse changes in the fillets. About 5% of the fillets were badly shredded during transportation of irradiated dried fish over a distance of about 2,400 km. (author). 27 refs, 6 figs, 13 tabs

  7. Spray-dried powders improve the controlled release of antifungal tioconazole-loaded polymeric nanocapsules compared to with lyophilized products

    International Nuclear Information System (INIS)

    Ribeiro, Roseane Fagundes; Motta, Mariana Heldt; Härter, Andréia Pisching Garcia; Flores, Fernanda Cramer; Beck, Ruy Carlos Ruver; Schaffazick, Scheila Rezende

    2016-01-01

    This work aimed to obtain solid formulations from polymeric nanocapsules and nanoemulsions containing tioconazole, a broad spectrum antifungal drug. Two dehydration methods were used: spray-drying and freeze-drying, using lactose as adjuvant (10%, w/v). The liquid formulations had a mean particle size around 206 nm and 182 nm for nanocapsules and nanoemulsions, respectively, and an adequate polydispersity index. Tioconazole content was close to the theoretical amount (1.0 mg/mL). After drying, the content ranged between 98 and 102% with a mean nanometric size of the dried products after redispersion. Scanning electron microscopy showed that the particles are rounded, sphere-shaped for the dried products obtained by spray-drying, and shapeless and irregular shapes for those obtained by freeze-drying. In the microbiological evaluation, all dried products remained active against the yeast Candida albicans when compared to the original systems. The dried products obtained by spray-drying from nanocapsules presented better control of the tioconazole release when compared to the freeze-drying products. - Highlights: • Polymeric nanocapsule suspensions containing tioconazole were submitted to spray-drying and freeze-drying. • Dried products from nanocapsule suspensions were stable for 30 days. • Release studies showed that the dried products presented greater control of drug release compared to the original suspension.

  8. Spray-dried powders improve the controlled release of antifungal tioconazole-loaded polymeric nanocapsules compared to with lyophilized products

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Roseane Fagundes [Programa de Pós-Graduação em Ciências Farmacêuticas, Universidade Federal de Santa Maria, Av. Roraima, 1000, Santa Maria, RS, 97105-900 (Brazil); Motta, Mariana Heldt [Curso de Farmácia, Centro de Ciências da Saúde, Universidade Federal de Santa Maria, Av. Roraima, 1000, Santa Maria, RS, 97105-900 (Brazil); Härter, Andréia Pisching Garcia; Flores, Fernanda Cramer [Programa de Pós-Graduação em Ciências Farmacêuticas, Universidade Federal de Santa Maria, Av. Roraima, 1000, Santa Maria, RS, 97105-900 (Brazil); Beck, Ruy Carlos Ruver [Programa de Pós-Graduação em Ciências Farmacêuticas, Faculdade de Farmácia, Universidade Federal do Rio Grande do Sul, Av. Ipiranga, 2752, Porto Alegre, RS, 90610-000 (Brazil); Schaffazick, Scheila Rezende [Programa de Pós-Graduação em Ciências Farmacêuticas, Universidade Federal de Santa Maria, Av. Roraima, 1000, Santa Maria, RS, 97105-900 (Brazil); and others

    2016-02-01

    This work aimed to obtain solid formulations from polymeric nanocapsules and nanoemulsions containing tioconazole, a broad spectrum antifungal drug. Two dehydration methods were used: spray-drying and freeze-drying, using lactose as adjuvant (10%, w/v). The liquid formulations had a mean particle size around 206 nm and 182 nm for nanocapsules and nanoemulsions, respectively, and an adequate polydispersity index. Tioconazole content was close to the theoretical amount (1.0 mg/mL). After drying, the content ranged between 98 and 102% with a mean nanometric size of the dried products after redispersion. Scanning electron microscopy showed that the particles are rounded, sphere-shaped for the dried products obtained by spray-drying, and shapeless and irregular shapes for those obtained by freeze-drying. In the microbiological evaluation, all dried products remained active against the yeast Candida albicans when compared to the original systems. The dried products obtained by spray-drying from nanocapsules presented better control of the tioconazole release when compared to the freeze-drying products. - Highlights: • Polymeric nanocapsule suspensions containing tioconazole were submitted to spray-drying and freeze-drying. • Dried products from nanocapsule suspensions were stable for 30 days. • Release studies showed that the dried products presented greater control of drug release compared to the original suspension.

  9. Effects of Mg on C and N Metabolism of Soybean at Different Nitrogen Supplying Levels

    Institute of Scientific and Technical Information of China (English)

    LANG Man; LIU Yuanying; PENG Xianlong; ZHANG Wenzhao

    2006-01-01

    A pot experiment was conducted to study the effects of magnesium on carbon and nitrogen metabolism of soybean at different nitrogen supplying levels. The results showed that the effects of magnesium at low nitrogen rate on N content, soluble protein, soluble sugar contents were not alike at different growth stage, although nodule dry weights raised, the yield and protein content of seeds decreased, however, the oil content was improved.The application of magnesium at medium and high nitrogen supplying levels promoted the uptake of N effectively,increased the soluble protein and soluble sugar contents, but the nodule dry weights of application magnesium at medium nitrogen supplying level decreased and the yield increased only a little despite the improved quality.Application of magnesium at high nitrogen supplying level raised nodule dry weights and soybean yield significantly, the quality of seeds was also improved.

  10. Dry needling in lateral epicondylitis: a prospective controlled study.

    Science.gov (United States)

    Uygur, Esat; Aktaş, Birol; Özkut, Afşar; Erinç, Samet; Yilmazoglu, Emime Gül

    2017-11-01

    Lateral epicondylitis (LE), a common disease, especially in middle age, causes decreased productivity and economic losses. The first-line treatment for LE is conservative and consists of topical and oral anti-inflammatory drugs, ice application, and brace use. If the first-line treatment fails, second-line treatment modalities, which are generally invasive, are offered. Second-line therapeutic regimens include saline, corticosteroid, or platelet-rich plasma injections. Dry needling is relatively new. We hypothesized that dry needling would be at least as effective as first-line treatment for LE. We compared the outcomes of first-line treatment and dry needling. The study allocated 110 patients into groups using online randomization software. After completing the Patient-rated Tennis Elbow Evaluation (PRTEE), patients in group I received dry needling, whereas those in group II received first-line treatment, consisting of ibuprofen 100 mg twice a day and a proximal forearm brace. The patients were evaluated after three weeks and six months. The study ultimately analyzed 92 patients. Although both treatment methods were effective at three weeks, dry needling was significantly more effective than the first-line treatment at six months. Because of the low complication rate, dry needling is a safe method, and it might be an effective treatment option for LE.

  11. Drying of α-amylase by spray drying and freeze-drying - a comparative study

    Directory of Open Access Journals (Sweden)

    S. S. de Jesus

    2014-09-01

    Full Text Available This study is aimed at comparing two traditional methods of drying of enzymes and at verifying the efficiency of each one and their advantages and disadvantages. The experiments were performed with a laboratory spray dryer and freeze-dryer using α-amylase as the model enzyme. An experimental design in star revealed that spray drying is mainly influenced by the inlet air temperature and feed flow rate, which were considered to be the main factors influencing the enzymatic activity and water activity; the long period of material exposure to high temperatures causes a partial activity loss. In the experiments of freeze drying, three methods of freezing were used (freezer, acetone and dry ice, and liquid nitrogen and samples subsequently freeze-dried for times ranging between 0-24 hours. The product obtained from the two techniques showed high enzymatic activity and low water activity. For the drying of heat-resistant enzymes, in which the product to be obtained does not have high added value, spray drying may be more economically viable because, in the freeze drying process, the process time can be considered as a limiting factor when choosing a technique.

  12. Mechanisms of Weight Regain following Weight Loss.

    Science.gov (United States)

    Blomain, Erik Scott; Dirhan, Dara Anne; Valentino, Michael Anthony; Kim, Gilbert Won; Waldman, Scott Arthur

    2013-01-01

    Obesity is a world-wide pandemic and its incidence is on the rise along with associated comorbidities. Currently, there are few effective therapies to combat obesity. The use of lifestyle modification therapy, namely, improvements in diet and exercise, is preferable over bariatric surgery or pharmacotherapy due to surgical risks and issues with drug efficacy and safety. Although they are initially successful in producing weight loss, such lifestyle intervention strategies are generally unsuccessful in achieving long-term weight maintenance, with the vast majority of obese patients regaining their lost weight during followup. Recently, various compensatory mechanisms have been elucidated by which the body may oppose new weight loss, and this compensation may result in weight regain back to the obese baseline. The present review summarizes the available evidence on these compensatory mechanisms, with a focus on weight loss-induced changes in energy expenditure, neuroendocrine pathways, nutrient metabolism, and gut physiology. These findings have added a major focus to the field of antiobesity research. In addition to investigating pathways that induce weight loss, the present work also focuses on pathways that may instead prevent weight regain. Such strategies will be necessary for improving long-term weight loss maintenance and outcomes for patients who struggle with obesity.

  13. No Heat Spray Drying Technology

    Energy Technology Data Exchange (ETDEWEB)

    Beetz, Charles [ZoomEssence, Inc., Hebron, KY (United States)

    2016-06-15

    No Heat Spray Drying Technology. ZoomEssence has developed our Zooming™ spray drying technology that atomizes liquids to powders at ambient temperature. The process of drying a liquid into a powder form has been traditionally achieved by mixing a heated gas with an atomized (sprayed) fluid within a vessel (drying chamber) causing the solvent to evaporate. The predominant spray drying process in use today employs air heated up to 400° Fahrenheit to dry an atomized liquid into a powder. Exposing sensitive, volatile liquid ingredients to high temperature causes molecular degradation that negatively impacts solubility, stability and profile of the powder. In short, heat is detrimental to many liquid ingredients. The completed award focused on several areas in order to advance the prototype dryer to a commercial scale integrated pilot system. Prior to the award, ZoomEssence had developed a prototype ‘no-heat’ dryer that firmly established the feasibility of the Zooming™ process. The award focused on three primary areas to improve the technology: (1) improved ability to formulate emulsions for specific flavor groups and improved understanding of the relationship of emulsion properties to final dry particle properties, (2) a new production atomizer, and (3) a dryer controls system.

  14. Facile fabrication of hydrophobic surfaces on mechanically alloyed-Mg/HA/TiO{sub 2}/MgO bionanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Khalajabadi, Shahrouz Zamani [Medical Devices and Technology Group (MEDITEG), Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Abdul Kadir, Mohammed Rafiq, E-mail: rafiq@biomedical.utm.my [Medical Devices and Technology Group (MEDITEG), Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Izman, Sudin; Mohd Yusop, Mohd Zamri [Department of Materials, Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia)

    2015-01-01

    Highlights: • Mg/HA/TiO{sub 2}-based nanocomposite was produced using mechanical alloying. • The hydrophobic surface coverage was fabricated on the mechanical alloyed samples by annealing. • The morphological characteristics, phase evolution and wettability of nanocomposites and the hydrophobic surface coverage were investigated. • The activation energies and reaction kinetic of the powder mixture of nanocomposites were calculated. - Abstract: The effect of mechanical alloying and post-annealing on the phase evolution, microstructure, wettability and thermal stability of Mg–HA–TiO{sub 2}–MgO composites was investigated in this study. Phase evolution and microstructure analysis were performed using X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy and atomic force microscopy, as well as the wettability determined by contact angle measurements with SBF. The 16-h mechanical alloying resulted in the formation of MgTiO{sub 3}, CaTiO{sub 3}, Mg{sub 3}(PO{sub 4}){sub 2} and Mg(OH){sub 2} phases and a decrease in wettability of the nanocomposites. A hydrophobic film with hierarchical structures comprising nanoflakes of MgTiO{sub 3}, nano-cuboids of CaTiO{sub 3}, microspheres of Mg{sub 3}(PO{sub 4}){sub 2} and Mg(OH){sub 2} was successfully constructed on the surface of the Mg-based nanocomposites substrates as a result of the post-annealing process. After 1-h annealing at 630 °C, the synthesized hydrophobic surface on the nanocomposite substrates decreased the wettability, as the 8-h-mechanically alloyed samples exhibited a contact angle close to 93°. The formation activation energies and reaction kinetics of the powder mixture were investigated using differential thermal analysis and thermal gravimetric analysis. The released heat, weight loss percentage and reaction kinetics increased, while the formation activation energies of the exothermic reactions decreased following an increase in the milling time.

  15. Dry Mouth Treatment: Tips for Controlling Dry Mouth

    Science.gov (United States)

    ... mouthwashes that contain alcohol because they can be drying. Stop all tobacco use if you smoke or ... also help your condition: Avoid sugary or acidic foods and drinks because they increase your risk of ...

  16. Proven Weight Loss Methods

    Science.gov (United States)

    Fact Sheet Proven Weight Loss Methods What can weight loss do for you? Losing weight can improve your health in a number of ways. It can lower ... at www.hormone.org/Spanish . Proven Weight Loss Methods Fact Sheet www.hormone.org

  17. Carpel size, grain filling, and morphology determine individual grain weight in wheat

    OpenAIRE

    Xie, Quan; Mayes, Sean; Sparkes, Debbie L.

    2015-01-01

    Individual grain weight is a major yield component in wheat. To provide a comprehensive understanding of grain weight determination, the carpel size at anthesis, grain dry matter accumulation, grain water uptake and loss, grain morphological expansion, and final grain weight at different positions within spikelets were investigated in a recombinant inbred line mapping population of bread wheat (Triticum aestivum L.)?spelt (Triticum spelta L.). Carpel size, grain dry matter and water accumulat...

  18. Is dry cleaning all wet?

    International Nuclear Information System (INIS)

    Ryan, M.

    1993-01-01

    Chemical solvents from dry cleaning, particularly perchloroethylene (perc), have contributed to groundwater contamination, significant levels of air pollution in and around cleaners, and chemical accumulation in food. Questions are being raised about the process of cleaning clothes with chemical, and other less toxic cleaning methods are being explored. The EPA has focused attention on the 50 year old Friedburg method of cleaning, Ecoclean, which uses no dangerous chemicals and achieves comparable results. Unfortunately, the cleaning industry is resistant to change, so cutting back on amount of clothes that need dry cleaning and making sure labels aren't exaggerating when they say dry clean only, is frequently the only consumer option now

  19. Land application uses of dry FGD by-products. [Quarterly] report, July 1, 1993--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Dick, W.A.; Beeghly, J.H.

    1993-12-31

    Reclamation of mine-sites with acid overburden requires the use of alkaline amendments and represents a potential high-volume use of alkaline dry flue gas desulfurization (FGD) by products. In a greenhouse study, 25-cm columns of acid mine spoil were amended with two FGD by-products; lime injection multistage burners (LIMB) fly ash or pressurized fluidized bed (PFBC) fly ash at rates of 0, 4, 8, 16, and 32% by weight (0, 40, 80, 160, and 320 tons/acre). Amended spoil was covered with 20 cm of acid topsoil amended with the corresponding FGD by-product to pH 7. Column leachate pH increased with FGD amendment rate while leachate Fe, Mn, and Zn decreased, Leachate Ca, S, and Mg decreased with LIMB amendment rate and increased with PFBC amendment. Leachate concentrations of regulated metals were decreased or unaffected by FGD amendment except for Se which was increased by PFBC. Spoil pH was increased up to 8.9 by PFBC, and up to 9.2 by LIMB amendment. Spoil pH also increased with depth with FGD amendments of 16 and 32%, Yield of fescue was increased by FGD amendment of 4 to 8%. Plant tissue content of most elements was unaffected by FGD amendment rate, and no toxicity symptoms were observed. Plant Ca and Mg were increased by LIMB and PFBC respectively, while plant S, Mn and Sr were decreased. Plant Ca and B was increased by LIMB, and plant Mg and S by PFBC amendment. These results indicate dry FGD by-products are effective in ameliorating acid, spoils and have a low potential for creating adverse environmental impacts.

  20. Physicochemical properties of direct compression tablets with spray dried and ball milled solid dispersions of tadalafil in PVP-VA.

    Science.gov (United States)

    Wlodarski, K; Tajber, L; Sawicki, W

    2016-12-01

    The aim of this research was to develop immediate release tablets comprising solid dispersion (IRSDTs) of tadalafil (Td) in a vinylpyrrolidone and vinyl acetate block copolymer (PVP-VA), characterized by improved dissolution profiles. The solid dispersion of Td in PVP-VA (Td/PVP-VA) in a weight ratio of 1:1 (w/w) was prepared using two different processes i.e. spray drying and ball milling. While the former process has been well established in the formulation of IRSDTs the latter has not been exploited in these systems yet. Regardless of the preparation method, both Td/PVP-VA solid dispersions were amorphous as confirmed by PXRD, DSC and FTIR. However, different morphology of particles (SEM) resulted in differences in water apparent solubility and disk intrinsic dissolution rate (DIDR). Both solid dispersions and crystalline Td were successfully made into directly compressible tablets at three doses of Td, i.e. 2.5mg, 10mgand20mg, yielding nine different formulations (D 1 -D 9 ). Each of the lots met the requirements set by Ph.Eur. and was evaluated with respect to appearance, diameter, thickness, mass, hardness, friability, disintegration time and content of Td. IRSDTs performed as supersaturable formulations and had significantly improved water dissolution profiles in comparison with equivalent tablets containing crystalline Td and the marketed formulations. Tablets with both spray dried and ball milled Td/PVP-VA revealed the greatest improvement in dissolution depending on the investigated doses, i.e. 2.5mgand20mg, respectively. Also, dissolution of Td from Td/PVP-VA delivered in different forms occurred in the following order: powders>tablets>capsules. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Spent fuel drying system test results (second dry-run)

    International Nuclear Information System (INIS)

    Klinger, G.S.; Oliver, B.M.; Abrefah, J.; Marschman, S.C.; MacFarlan, P.J.; Ritter, G.A.

    1998-07-01

    The water-filled K-Basins in the Hanford 100 Area have been used to store N-Reactor spent nuclear fuel (SNF) since the 1970s. Because some leaks have been detected in the basins and some of the fuel is breached due to handling damage and corrosion, efforts are underway to remove the fuel elements from wet storage. An Integrated Process Strategy (IPS) has been developed to package, dry, transport, and store these metallic uranium fuel elements in an interim storage facility on the Hanford Site (WHC 1995). Information required to support the development of the drying processes, and the required safety analyses, is being obtained from characterization tests conducted on fuel elements removed from the K-Basins. A series of whole element drying tests (reported in separate documents, see Section 7.0) have been conducted by Pacific Northwest National Laboratory (PNNL) on several intact and damaged fuel elements recovered from both the K-East and K-West Basins. This report documents the results of the second dry-run test, which was conducted without a fuel element. With the concurrence of project management, the test protocol for this run, and subsequent drying test runs, was modified. These modifications were made to allow for improved data correlation with drying procedures proposed under the IPS. Details of these modifications are discussed in Section 3.0

  2. Strong, Ductile, and Thermally Stable bcc-Mg Nanolaminates.

    Science.gov (United States)

    Pathak, Siddhartha; Velisavljevic, Nenad; Baldwin, J Kevin; Jain, Manish; Zheng, Shijian; Mara, Nathan A; Beyerlein, Irene J

    2017-08-15

    Magnesium has attracted attention worldwide because it is the lightest structural metal. However, a high strength-to-weight ratio remains its only attribute, since an intrinsic lack of strength, ductility and low melting temperature severely restricts practical applications of Mg. Through interface strains, the crystal structure of Mg can be transformed and stabilized from a simple hexagonal (hexagonal close packed hcp) to body center cubic (bcc) crystal structure at ambient pressures. We demonstrate that when introduced into a nanocomposite bcc Mg is far more ductile, 50% stronger, and retains its strength after extended exposure to 200 C, which is 0.5 times its homologous temperature. These findings reveal an alternative solution to obtaining lightweight metals critically needed for future energy efficiency and fuel savings.

  3. Effects of Dietary Supplementation of Dried Distillers Grain with Solubles (DDGS and Yucca (Yucca schidigera on Broiler Performance, Carcass Traits, Intestinal Viscosity and Marketing

    Directory of Open Access Journals (Sweden)

    Savaş Sariozkan

    2016-01-01

    Full Text Available This study was conducted to determine the effects of dietary supplementation of dried distillers’ grain with soluble (DDGS and yucca (Yucca schidigera on broiler performance, intestinal viscosity, carcass traits, and marketing. A total of 360, 21-d-old male broiler chickens were divided into 4 groups as 1: Control (C, corn based diet, without DDGS and yucca (Y supplementation, 2: DDGS (30%, 3: C + Y (120 mg/kg Yucca and 4: DDGS (30% + Y (120 mg/kg with 6 replicates (15 chicks x 6 replicates. The study was performed between 21 to 42 days of age. As a result, there were no significant differences among the groups in terms of body weight, body weight gain, feed consumption, feed conversion ratio and mortality rate (P>0.05. The carcass traits and effects of different marketing type (whole sale or cutting parts on profit were compared. A slight decrease was determined in group 4 in terms of leg quarter ratio to cold carcass weight and carcass yield. Intestinal viscosity, bacterial counts and pH values (in duodenum and ileum were not different among the groups (P>0.05. The lowest production cost was determined in DDGS and DDGS+Y groups (P

  4. Optimasi Proses Spray Drying Pada Enkapsulasi Antosianin Ubi Ungu

    Directory of Open Access Journals (Sweden)

    Retno Yunilawati

    2018-04-01

    Full Text Available Teknologi proses spray drying banyak dilakukan pada enkapsulasi zat warna alam untuk aplikasi di industri. Pada penelitian ini dilakukan enkapsulasi antosianin ubi ungu dengan teknik spray drying. Tujuan dari penelitian ini adalah optimasi proses spray drying pada enkapsulasi antosianin ubi ungu. Optimasi proses dilakukan pada kondisi berbagai suhu inlet (150 °C sampai dengan 180 °C dan jumlah maltodekstrin sebagai carrier (5% sampai dengan 15%. Sebagai respon dilakukan pengukuran kadar air, absorbansi, dan kadar antosianin. Response Surface Methodology (RSM dengan metode Central Composite Design (CCD digunakan untuk analisis data optimasi. Hasil analisis menunjukkan bahwa suhu inlet dan persentase maltodekstrin berpengaruh secara signifikan terhadap kadar air, absorbansi, dan kadar antosianin total. Kondisi optimal didapatkan pada suhu inlet 166,96 °C dan maltodekstrin sebesar 5%. Pada kondisi ini dihasilkan serbuk antosianin ubi ungu dengan kadar air 4,79%; absorbansi 0,8827; dan kadar antosianin total 968,65 mg/kg.

  5. The Abundance of Mg in the Interstellar Medium

    Science.gov (United States)

    Fitzpatrick, Edward L.

    1997-06-01

    An empirical determination of the f-values of the far-UV Mg II λλ1239, 1240 lines is reported. The strong near-UV Mg II λλ2796, 2803 lines are generally highly saturated along most interstellar sight lines outside the local interstellar medium (ISM) and usually yield extremely uncertain estimates of Mg+ column densities in interstellar gas. Since Mg+ is the dominant form of Mg in the neutral ISM, and since Mg is expected to be a significant constituent of interstellar dust grains, the far-UV lines are critical for assessing the role of this important element in the ISM. This study consists of complete component analyses of the absorption along the lines of sight toward HD 93521 in the Galactic halo and ξ Persei and ζ Ophiuchi in the Galactic disk, including all four UV Mg+ lines and numerous other transitions. The three analyses yield consistent determinations of the λλ1239, 1240 f-values, with weighted means of (6.4 +/- 0.4) × 10-4 and (3.2 +/- 0.2) × 10-4, respectively. These results are a factor of ~2.4 larger than a commonly used theoretical estimate, and a factor of ~2 smaller than a recently suggested empirical revision. The effects of this result on gas- and dust-phase abundance measurements of Mg are discussed. Based on observations with the NASA/ESA Hubble Space Telescope, obtained at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, under NASA contract NAS5-2655. This Letter is dedicated to the memory of Professor Lyman Spitzer Jr. He was a great guy.

  6. Administration of dried Aloe vera gel powder reduced body fat mass in diet-induced obesity (DIO) rats.

    Science.gov (United States)

    Misawa, Eriko; Tanaka, Miyuki; Nabeshima, Kazumi; Nomaguchi, Kouji; Yamada, Muneo; Toida, Tomohiro; Iwatsuki, Keiji

    2012-01-01

    The aim of the present study was to investigate the anti-obesity effects of Aloe vera gel administration in male Sprague-Dawley (SD) rats with diet-induced obesity (DIO). SD rats at 7 wk of age were fed either a standard diet (10 kcal% fat) (StdD) or high-fat (60 kcal% fat) diet (HFD) during the experimental period. Four weeks after of HFD-feeding, DIO rats (11 wk of age) were orally administered with two doses of Aloe vera gel powder (20 and 200 mg/kg/d) for 90 d. Body weights (g) and body fat (%) of HFD fed rats were significantly higher than those of StdD-fed rats. Although a modest decrease of body weight (g) was observed with the administration of dried Aloe vera gel powder, both subcutaneous and visceral fat weight (g) and body fat (%) were reduced significantly in Aloe vera gel-treated rats. Serum lipid parameters elevated by HFD were also improved by the Aloe vera gel treatment. The oxygen consumption (VO(2)), an index of energy expenditure, was decreased in HFD-fed rats compared with that in StdD-fed rats. Administration of Aloe vera gel reversed the change in VO(2) in the HFD-fed rats. These results suggest that intake of Aloe vera gel reduced body fat accumulation, in part, by stimulation of energy expenditure. Aloe vera gel might be beneficial for the prevention and improvement of diet-induced obesity.

  7. Air dehumidification and drying processes

    Energy Technology Data Exchange (ETDEWEB)

    Steiner, R.

    1988-07-01

    Details are given on the physical principles of air dehumidification and drying as well as on appropriate systems available on the market. Reference is made to dehumidification through condensation (intermittent compressor or electric auxiliary heater defrosting, reversible-circuit hot gas bypass defrosting), air drying through sorption (sorbents, regeneration through heat inputs), the operation of absorptive dryers (schematic sketches), and the change of state of air (Mollier h,x-diagramm). Practical examples refer to the dehumidification of storage rooms, archives, and waterworks as well as to air drying in the pharmaceutical industry, the pastry and candy industry, the food industry, and the drying (preservation) of turbines and generators during long standstill periods. A diagramm shows that while adsorption processes are efficient at temperatures below 80/sup 0/C, low-temperature dehumidification is efficient at temperatures above. (HWJ).

  8. Simple Solutions for Dry Eye

    Science.gov (United States)

    Patient Education Sheet Simple Solutions for Dry Eye The SSF thanks J. Daniel Nelson, MD, Associate Medical Director, Specialty Care HealthPartners Medical Group & Clinics, and Professor of Ophthalmology, University of ...

  9. Sustaining dry surfaces under water

    DEFF Research Database (Denmark)

    Jones, Paul R.; Hao, Xiuqing; Cruz-Chu, Eduardo R.

    2015-01-01

    Rough surfaces immersed under water remain practically dry if the liquid-solid contact is on roughness peaks, while the roughness valleys are filled with gas. Mechanisms that prevent water from invading the valleys are well studied. However, to remain practically dry under water, additional...... mechanisms need consideration. This is because trapped gas (e.g. air) in the roughness valleys can dissolve into the water pool, leading to invasion. Additionally, water vapor can also occupy the roughness valleys of immersed surfaces. If water vapor condenses, that too leads to invasion. These effects have...... not been investigated, and are critically important to maintain surfaces dry under water.In this work, we identify the critical roughness scale, below which it is possible to sustain the vapor phase of water and/or trapped gases in roughness valleys – thus keeping the immersed surface dry. Theoretical...

  10. Dry skin - self-care

    Science.gov (United States)

    ... pat skin dry then apply your moisturizer. Avoid skin care products and soaps that contain alcohol, fragrances, dyes, or other chemicals. Take short, warm baths or showers. Limit your ... gentle skin cleansers or soap with added moisturizers. Only use ...

  11. Emulsion type dry cleaning system

    International Nuclear Information System (INIS)

    Kohanawa, Osamu; Matsumoto, Hiroyo.

    1988-01-01

    Protective clothing against radioactive contamination used in the radiation controlled areas of nuclear plants has been washed by the same wet washing as used for underwear washing, but recently dry cleaning is getting used in place of wet washing, which generates a large quantity of laundry drain. However, it was required to use wet washing once every five to ten dry cleanings for washing protective clothing, because conventional dry cleaning is less effective in removing water-soluble soils. Therefore, in order to eliminate wet washing, and to decrease the quantity of laundry drains, the emulsion type dry cleaning system capable of removing both oil-soluble and water-soluble soils at a time has been developed. The results of developmental experiments and actual application are presented in this paper. (author)

  12. Anthology of dry storage solutions

    Energy Technology Data Exchange (ETDEWEB)

    Allimann, Nathalie; Otton, Camille [AREVA, Paris (France)

    2012-03-15

    Around 35,000 PWR, BWR or Veer used fuel elements with various enrichment value up to 5%, various cooling time down to 2 years and various burn-ups up to 60,000 Mwd/tU are currently stored in AREVA dry storage solutions. These solutions are delivered in the United States, in Japan and in many European countries like Belgium, Switzerland, Italy, Armenia and Germany. With more than 1000 dry storage solutions delivered all over the world AREVA is the leader on this market. Dealing with dry storage is not an easy task. Products have to be flexible, to be adapted to customer needs and to the national regulations which may stipulate very strict tests such as airplane crash or simulation of earthquake. To develop a dry storage solution for a foreign country means to deal with its national competent authorities. All the national competent authorities do not have the same requirements. Storage conditions may also be different.

  13. Anthology of dry storage solutions

    International Nuclear Information System (INIS)

    Allimann, Nathalie; Otton, Camille

    2012-01-01

    Around 35,000 PWR, BWR or Veer used fuel elements with various enrichment value up to 5%, various cooling time down to 2 years and various burn-ups up to 60,000 Mwd/tU are currently stored in AREVA dry storage solutions. These solutions are delivered in the United States, in Japan and in many European countries like Belgium, Switzerland, Italy, Armenia and Germany. With more than 1000 dry storage solutions delivered all over the world AREVA is the leader on this market. Dealing with dry storage is not an easy task. Products have to be flexible, to be adapted to customer needs and to the national regulations which may stipulate very strict tests such as airplane crash or simulation of earthquake. To develop a dry storage solution for a foreign country means to deal with its national competent authorities. All the national competent authorities do not have the same requirements. Storage conditions may also be different

  14. Use of a non-linear method for including the mass uncertainty of gravimetric standards and system measurement errors in the fitting of calibration curves for XRFA freeze-dried UNO3 standards

    International Nuclear Information System (INIS)

    Pickles, W.L.; McClure, J.W.; Howell, R.H.

    1978-05-01

    A sophisticated nonlinear multiparameter fitting program was used to produce a best fit calibration curve for the response of an x-ray fluorescence analyzer to uranium nitrate, freeze dried, 0.2% accurate, gravimetric standards. The program is based on unconstrained minimization subroutine, VA02A. The program considers the mass values of the gravimetric standards as parameters to be fit along with the normal calibration curve parameters. The fitting procedure weights with the system errors and the mass errors in a consistent way. The resulting best fit calibration curve parameters reflect the fact that the masses of the standard samples are measured quantities with a known error. Error estimates for the calibration curve parameters can be obtained from the curvature of the ''Chi-Squared Matrix'' or from error relaxation techniques. It was shown that nondispersive XRFA of 0.1 to 1 mg freeze-dried UNO 3 can have an accuracy of 0.2% in 1000 s

  15. Post-LASIK dry eye

    OpenAIRE

    Shtein, Roni M

    2011-01-01

    Laser-assisted in situ keratomileusis (LASIK) is a frequently performed corneal refractive surgery with excellent refractive outcomes. The most common complication of LASIK is dry eyes, with virtually all patients developing some degree of dryness in the immediate postoperative period. Identifying preoperative dry eyes, and conscientious attention and treatment in the perioperative time period, can lead to enhanced patient satisfaction and more accurate visual outcomes. Improved understanding...

  16. Dry and coating of powders

    International Nuclear Information System (INIS)

    Alonso, M.; Alguacil, F. J.

    1999-01-01

    This paper presents a review on the mixing and coating of powders by dry processes. The reviews surveys fundamental works on mixture characterization (mixing index definitions and sampling techniques), mixing mechanisms and models, segregation with especial emphasis on free-surface segregation, mixing of cohesive powders and interparticle forces, ordered mixing (dry coating) including mechanism, model and applications and mixing equipment selection. (Author) 180 refs

  17. Photovoltaic assisted solar drying system

    International Nuclear Information System (INIS)

    Ruslan, M.H.; Othman, M.Y.; Baharuddin Yatim; Kamaruzzaman Sopian; Ali, M.I.; Ibarahim, Z.

    2006-01-01

    A photovoltaic assisted solar drying system has been constructed at the Solar Energy Research Park, Universiti Kebangsaan Malaysia. This drying system uses a custom designed parallel flow V-groove type collector. A fan powered by photovoltaic source assists the air flow through the drying system. A funnel with increasing diameter towards the top with ventilator turbine is incorporated into the system to facilitate the air flow during the absence of photovoltaic energy source. This drying system is designed with high efficiency and portability in mind so that it can readily be used at plantation sites where the crops are harvested or produced. A daily mean efficiency about 44% with mean air flow rate 0.16 kgs -1 has been achieved at mean daily radiation intensity of 800 Wm -2 . daily mean temperature of air drying chamber under the above conditions is 46 o C. Study has shown that the air flow and air temperature increase with the increase of solar radiation intensity. On a bright sunny day with instantaneous solar intensity about 600 Wm -2 , the temperature of air entering the drying chamber of 45 o C has been measured. In the absence of photovoltaic or in natural convection flow, the instantaneous efficiency decreased when solar radiation increased. The instantaneous efficiency recorded are 35% and 27% respectively at 570 Wm -2 and 745 Wm -2 of solar radiation. The temperature of drying chamber for the same amount of solar radiation are 42 o C and 48 o C respectively. Thus, the solar dryer shows a great potential for application in drying process of agricultural produce

  18. Dry Orgasm (Orgasm without Discharge of Semen)

    Science.gov (United States)

    Symptoms Dry orgasm By Mayo Clinic Staff Dry orgasm occurs when a man reaches sexual climax but doesn't release (ejaculate) ... the thick, white fluid that carries sperm. Dry orgasm usually isn't harmful, but it can interfere ...

  19. Dry Eyes and Glaucoma: Double Trouble

    Science.gov (United States)

    ... Involved News About Us Donate In This Section Dry Eyes and Glaucoma: Double Trouble email Send this article ... eye disease bothers the patient more. What Causes Dry Eye Syndrome? Dry eye can be caused by many ...

  20. Efficiency and safety of subconjunctival injection of anti-VEGF agent - bevacizumab - in treating dry eye.

    Science.gov (United States)

    Jiang, Xiaodan; Lv, Huibin; Qiu, Weiqiang; Liu, Ziyuan; Li, Xuemin; Wang, Wei

    2015-01-01

    Dry eye is a chronic inflammatory ocular surface disease with high prevalence. The current therapies for dry eye remain to be unspecific and notcomprehensive. This study aims to explore safety and efficacy of a novel treatment - subconjunctival injection of bevacizumab - in dry eye patients. Sixty-four eyes of 32 dry eye patients received subconjunctival injection of 100 μL 25 mg/mL bevacizumab. Dry eye symptoms, signs (corrected visual acuity, intraocular pressure, conjunctival vascularity, corneal staining, tear break-up time, Marx line score, and blood pressure), and conjunctival impression cytology were evaluated 3 days before and 1 week, 1 month, and 3 months after injection. Significant improvements were observed in dry eye symptoms, tear break-up time, and conjunctival vascularization area at all the visits after injection compared to the baseline (Pdry eye disease.

  1. Influence of drying treatments on antioxidant capacity of forage legume leaves.

    Science.gov (United States)

    Sang, Saw Yei; Jamharee, Fazrina; Prasad, K Nagendra; Azlan, Azrina; Maliki, Nurzillah

    2014-05-01

    This study was aimed to investigate the antioxidant capacities of four common forage legume leaves namely, Arachis pintoi (Pintoi), Calapogonium mucunoides (Calapo), Centrosema pubescens (Centro), and Stylosanthes guanensis (Stylo). Two different drying methods (oven-drying and freeze-drying) were employed and antioxidant activities were determined by DPPH, Ferric Reducing Antioxidant Power (FRAP) and β-carotene bleaching assays. Total phenolic content (TPC) was determined using Folin-Ciocalteu assay. Freeze-dried extract showed the highest antioxidant activities by DPPH (EC50 values 1.17-2.13 mg/ml), FRAP (147.08-246.42 μM of Fe(2+)/g), and β-carotene bleaching (57.11-78.60%) compared to oven drying. Hence, freeze drying treatment could be considered useful in retention of antioxidant activity and phenolic content.

  2. Dry mouth and older people.

    Science.gov (United States)

    Thomson, W M

    2015-03-01

    Dry mouth is more common among older people than in any other age group. Appropriate definition and accurate measurement of dry mouth is critical for better understanding, monitoring and treatment of the condition. Xerostomia is the symptom(s) of dry mouth; it can be measured using methods ranging from single questions to multi-item summated rating scales. Low salivary flow (known as salivary gland hypofunction, or SGH) must be determined by measuring that flow. The relationship between SGH and xerostomia is not straightforward, but both conditions are common among older people, and they affect sufferers' day-to-day lives in important ways. The major risk factor for dry mouth is the taking of particular medications, and older people take more of those than any other age group, not only for symptomatic relief of various age-associated chronic diseases, but also in order to reduce the likelihood of complications which may arise from those conditions. The greater the number taken, the greater the associated anticholinergic burden, and the more likely it is that the individual will suffer from dry mouth. Since treating dry mouth is such a challenge for clinicians, there is a need for dentists, doctors and pharmacists to work together to prevent it occurring. © 2015 Australian Dental Association.

  3. Dry adhesives with sensing features

    International Nuclear Information System (INIS)

    Krahn, J; Menon, C

    2013-01-01

    Geckos are capable of detecting detachment of their feet. Inspired by this basic observation, a novel functional dry adhesive is proposed, which can be used to measure the instantaneous forces and torques acting on an adhesive pad. Such a novel sensing dry adhesive could potentially be used by climbing robots to quickly realize and respond appropriately to catastrophic detachment conditions. The proposed torque and force sensing dry adhesive was fabricated by mixing Carbon Black (CB) and Polydimethylsiloxane (PDMS) to form a functionalized adhesive with mushroom caps. The addition of CB to PDMS resulted in conductive PDMS which, when under compression, tension or torque, resulted in a change in the resistance across the adhesive patch terminals. The proposed design of the functionalized dry adhesive enables distinguishing an applied torque from a compressive force in a single adhesive pad. A model based on beam theory was used to predict the change in resistance across the terminals as either a torque or compressive force was applied to the adhesive patch. Under a compressive force, the sensing dry adhesive was capable of measuring compression stresses from 0.11 Pa to 20.9 kPa. The torque measured by the adhesive patch ranged from 2.6 to 10 mN m, at which point the dry adhesives became detached. The adhesive strength was 1.75 kPa under an applied preload of 1.65 kPa for an adhesive patch with an adhesive contact area of 7.07 cm 2 . (paper)

  4. Dry adhesives with sensing features

    Science.gov (United States)

    Krahn, J.; Menon, C.

    2013-08-01

    Geckos are capable of detecting detachment of their feet. Inspired by this basic observation, a novel functional dry adhesive is proposed, which can be used to measure the instantaneous forces and torques acting on an adhesive pad. Such a novel sensing dry adhesive could potentially be used by climbing robots to quickly realize and respond appropriately to catastrophic detachment conditions. The proposed torque and force sensing dry adhesive was fabricated by mixing Carbon Black (CB) and Polydimethylsiloxane (PDMS) to form a functionalized adhesive with mushroom caps. The addition of CB to PDMS resulted in conductive PDMS which, when under compression, tension or torque, resulted in a change in the resistance across the adhesive patch terminals. The proposed design of the functionalized dry adhesive enables distinguishing an applied torque from a compressive force in a single adhesive pad. A model based on beam theory was used to predict the change in resistance across the terminals as either a torque or compressive force was applied to the adhesive patch. Under a compressive force, the sensing dry adhesive was capable of measuring compression stresses from 0.11 Pa to 20.9 kPa. The torque measured by the adhesive patch ranged from 2.6 to 10 mN m, at which point the dry adhesives became detached. The adhesive strength was 1.75 kPa under an applied preload of 1.65 kPa for an adhesive patch with an adhesive contact area of 7.07 cm2.

  5. Dry dock gate stability modelling

    Science.gov (United States)

    Oktoberty; Widiyanto; Sasono, E. J.; Pramono, S.; Wandono, A. T.

    2018-03-01

    The development of marine transportation needs in Indonesia increasingly opens national shipyard business opportunities to provide shipbuilding services to the shipbuilding vessels. That emphasizes the stability of prime. The ship's decking door becomes an integral part of the efficient place and the specification of the use of the asset of its operational ease. This study aims to test the stability of Dry Dock gate with the length of 35.4 meters using Maxsurf and Hydromax in analyzing the calculation were in its assessment using interval per 500 mm length so that it can get detail data toward longitudinal and transverse such as studying Ship planning in general. The test result shows dry dock gate meets IMO standard with ballast construction containing 54% and 68% and using fix ballast can produce GMt 1,924 m, tide height 11,357m. The GMt value indicates dry dick gate can be stable and firmly erect at the base of the mouth dry dock. When empty ballast produces GMt 0.996 which means dry dock date is stable, but can easily be torn down. The condition can be used during dry dock gate treatment.

  6. Preparation and Hydrogen Storage Properties of Mg-Rich Mg-Ni Ultrafine Particles

    Directory of Open Access Journals (Sweden)

    Jianxin Zou

    2012-01-01

    Full Text Available In the present work, Mg-rich Mg-Ni ultrafine powders were prepared through an arc plasma method. The phase components, microstructure, and hydrogen storage properties of the powders were carefully investigated. It is found that Mg2Ni and MgNi2 could be obtained directly from the vapor state reactions between Mg and Ni, depending on the local vapor content in the reaction chamber. A nanostructured MgH2 + Mg2NiH4 hydrogen storage composite could be generated after hydrogenation of the Mg-Ni ultrafine powders. After dehydrogenation, MgH2 and Mg2NiH4 decomposed into nanograined Mg and Mg2Ni, respectively. Thermogravimetry/differential scanning calorimetry (TG/DSC analyses showed that Mg2NiH4 phase may play a catalytic role in the dehydriding process of the hydrogenated Mg ultrafine particles.

  7. Biocides in urban wastewater treatment plant influent at dry and wet weather: concentrations, mass flows and possible sources

    DEFF Research Database (Denmark)

    Bollmann, Ulla E.; Petersen, Camilla Tang; Eriksson, Eva

    2014-01-01

    in Denmark and Sweden during dry and wet weather. It was discovered, that biocides are detectable not only during wet weather but also during dry weather when leaching from façade coatings can be excluded as source. In most cases, the concentrations during dry weather were in the same range as during wet...... to 116 mg h(-1) carbendazim or 73 mg h(-1) mecoprop) supporting the hypothesis that the biocides were washed off by wind driven rain. Contrary, the biocide emissions during dry weather were rather related to household activities than with emissions from buildings, i.e., emissions were highest during...... morning and evening hours (up to 50 mg h(-1)). Emissions during night were significantly lower than during daytime. Only for propiconazole a different emission behaviour during dry weather was observed: the mass load peaked in the late afternoon (3 g h(-1)) and declined slowly afterwards. Most likely...

  8. Preparation of High-Grade Powders from Tomato Paste Using a Vacuum Foam Drying Method.

    Science.gov (United States)

    Sramek, Martin; Schweiggert, Ralf Martin; van Kampen, Andreas; Carle, Reinhold; Kohlus, Reinhard

    2015-08-01

    We present a rapid and gentle drying method for the production of high-grade tomato powders from double concentrated tomato paste, comparing results with powders obtained by foam mat air drying and freeze dried powders. The principle of this method consists of drying tomato paste in foamed state at low temperatures in vacuum. The formulations were dried at temperatures of 50, 60, and 70 °C and vacuum of 200 mbar. Foam stability was affected by low serum viscosity and the presence of solid particles in tomato paste. Consequently, serum viscosity was increased by maltodextrin addition, yielding optimum stability at tomato paste:maltodextrin ratio of 2.4:1 (w/w) in dry matter. Material foamability was improved by addition of 0.5% (w/w, fresh weight) egg white. Because of solid particles in tomato paste, foam air filling had to be limited to critical air volume fraction of Φ = 0.7. The paste was first pre-foamed to Φ = 0.2 and subsequently expanded in vacuo. After drying to a moisture content of 5.6% to 7.5% wet base (w.b.), the materials obtained were in glassy state. Qualities of the resulting powders were compared with those produced by freeze and air drying. Total color changes were the least after vacuum drying, whereas air drying resulted in noticeable color changes. Vacuum foam drying at 50 °C led to insignificant carotenoid losses, being equivalent to the time-consuming freeze drying method. In contrast, air drying caused lycopene and β-carotene losses of 18% to 33% and 14% to 19% respectively. Thus, vacuum foam drying enables production of high-grade tomato powders being qualitatively similar to powders obtained by freeze drying. © 2015 Institute of Food Technologists®

  9. Antioxidant activity, the content of total phenols and flavonoids in the ethanol extracts of Mentha longifolia (L. Hudson dried by the use of different techniques

    Directory of Open Access Journals (Sweden)

    Stanisavljević Dragana M.

    2012-01-01

    Full Text Available In this study, we have examined the yield of extracted substances obtained by means of extraction using 70 % ethanol (v/v, the content of total phenols and flavonoids, as well as the antioxidant activity of the extracts obtained from the samples of the herbs dried by means of different techniques. Wild mint Mentha longifolia (L. Hudson was dried naturally in a laboratory oven at a temperature of 45 °C and in an absorptive low temperature condensation oven at 35°C. The highest yield of extracts was obtained from the naturally dried herbs and the lowest from the herbs dried in the low temperature condensation drying oven. The content of total phenols and flavonoids was determined by spectrophotometric methods with an FC reagent and by the complexation reaction with aluminium-chloride, respectively. The extract of the naturally dried herbs had the highest overall content of phenols (113.8±2.0 mg of gallic acid/g of the dry extract and flavonoids (106.7±0.3 mg of rutin/g of the dry extract. The highest antioxidant activity determined by the FRAP and DPPH assay was determined in the extracts obtained from naturally dried herbs (2.76±0.15 mmol Fe2+/mg of the dry extract and EC50=0.022±0.001 mg/ml, while the lowest was obtained from the extracts of herbs dried in the laboratory oven (1.13±0.11 mmol Fe2+/mg of the dry extract and EC50=0.033±0.001 mg/ml. The HPLC-DAD analysis result show that the greatest content of phenolic compounds show extract obtained from naturally dried plant material. The dominant phenolic component in the all extracts is Kaempferol 3-O-glucoside. The content of all phenolic compound strongly depend on the drying conditions.

  10. Surface modification of an Mg-1Ca alloy to slow down its biocorrosion by chitosan

    International Nuclear Information System (INIS)

    Gu, X N; Zheng, Y F; Lan, Q X; Cheng, Y; Xi, T F; Zhang, Z X; Zhang, D Y

    2009-01-01

    The surface morphologies before and after immersion corrosion test of various chitosan-coated Mg-1Ca alloy samples were studied to investigate the effect of chitosan dip coating on the slowdown of biocorrosion. It showed that the corrosion resistance of the Mg-Ca alloy increased after coating with chitosan, and depended on both the chitosan molecular weight and layer numbers of coating. The Mg-Ca alloy coated by chitosan with a molecular weight of 2.7 x 10 5 for six layers has smooth and intact surface morphology, and exhibits the highest corrosion resistance in a simulated body fluid.

  11. Surface modification of an Mg-1Ca alloy to slow down its biocorrosion by chitosan

    Energy Technology Data Exchange (ETDEWEB)

    Gu, X N; Zheng, Y F; Lan, Q X [State Key Laboratory for Turbulence and Complex System and College of Engineering, Peking University, Beijing 100871 (China); Cheng, Y; Xi, T F [Center for Biomedical Materials and Tissue Engineering, Academy for Advanced Interdisciplinary Studies, Peking University, Beijing 100871 (China); Zhang, Z X [Biomedical Engineering Research Center, Research Institute of Peking University in Shenzhen, Shenzhen 518057 (China); Zhang, D Y, E-mail: gxn139888@pku.edu.c, E-mail: yfzheng@pku.edu.c, E-mail: 8lanqiuxiang@163.co, E-mail: chengyan@pku.edu.c, E-mail: top5460@163.co, E-mail: xitingfei@tom.co, E-mail: zhangdeyuan@lifetechmed.co [Lifetech Scientific (Shenzhen) Co. Ltd, Hi-Tech Park, Shenzhen 518000 (China)

    2009-08-15

    The surface morphologies before and after immersion corrosion test of various chitosan-coated Mg-1Ca alloy samples were studied to investigate the effect of chitosan dip coating on the slowdown of biocorrosion. It showed that the corrosion resistance of the Mg-Ca alloy increased after coating with chitosan, and depended on both the chitosan molecular weight and layer numbers of coating. The Mg-Ca alloy coated by chitosan with a molecular weight of 2.7 x 10{sup 5} for six layers has smooth and intact surface morphology, and exhibits the highest corrosion resistance in a simulated body fluid.

  12. Surface modification of an Mg-1Ca alloy to slow down its biocorrosion by chitosan.

    Science.gov (United States)

    Gu, X N; Zheng, Y F; Lan, Q X; Cheng, Y; Zhang, Z X; Xi, T F; Zhang, D Y

    2009-08-01

    The surface morphologies before and after immersion corrosion test of various chitosan-coated Mg-1Ca alloy samples were studied to investigate the effect of chitosan dip coating on the slowdown of biocorrosion. It showed that the corrosion resistance of the Mg-Ca alloy increased after coating with chitosan, and depended on both the chitosan molecular weight and layer numbers of coating. The Mg-Ca alloy coated by chitosan with a molecular weight of 2.7 x 10(5) for six layers has smooth and intact surface morphology, and exhibits the highest corrosion resistance in a simulated body fluid.

  13. Heating stage Raman and infrared emission spectroscopic study of the dehydroxylation of synthetic Mg-hydrotalcite

    International Nuclear Information System (INIS)

    Kloprogge, J.T.; Hickey, L.; Frost, R.L.

    1998-01-01

    Full text: Hydrotalcites, also described as anionic clays or layered double hydroxides (LDH), form an important group of compounds because of their catalytic (basic) activity, as a precursor for the preparation of oxidic catalysts as for other specific powder properties such as filler, UV-radiation stabiliser, chloride scavenger and thermal stabiliser (Titulaer, 1993). The structure of hydrotalcites can be visualised as positively charged hydroxide layers comparable to the hydroxide layers in brucite, Mg(OH) 2 , in which a part of the divalent metal is substituted by a trivalent metal separated by charge compensating mostly hydrated anions in a so-called interlayer between the hydroxide layers. In both naturally occurring and synthetic hydrotalcites a broad range of compositions are possible of the type [M 2+ 1-x M 3+ x (OH) 2 ][A n- ] x/n. yH 2 O, where M 2+ and M 3+ are the di- and trivalent cations in the octahedral positions within the hydroxide layers with x normally between 0.17 and 0.33. A n- is an exchangeable interlayer anion. The thermal behaviour of hydrotalcites is of importance for a number of applications indicated above. For example, when a hydrotalcite is used as a precursor for the preparation of mixed metal oxide catalysts the dehydration, decarbonisation and dehydroxylation reactions must be well known in order to control the final reaction product. The hydrotalcite Mg 6 Al 2 (OH) 16 CO 3 .nH 2 O was synthesised according to the method described before by Kloprogge and Frost (1999a,b). This method comprises the slow simultaneous addition of a mixed aluminium nitrate (0.25M)-magnesium nitrate (0.75M), aluminium nitrate (0.25M)-solutions and a mixed NaOH (2.00M)-Na 2 CO 3 (0.125M) solution under vigorous stirring buffering the pH at approximately 10. The product was washed to eliminate excess salt and dried at 60 deg C. The thermal behaviour of synthetic hydrotalcite, Mg 6 Al 2 (OH)O 16 CO 3 .nH 2 O, has been studied by Infrared Emission

  14. The Change of Total Anthocyanins in Blueberries and Their Antioxidant Effect After Drying and Freezing

    Directory of Open Access Journals (Sweden)

    Virachnee Lohachoompol

    2004-01-01

    Full Text Available This study examined the effects of freezing, storage, and cabinet drying on the anthocyanin content and antioxidant activity of blueberries (Vaccinium corymbosum L. Fresh samples were stored for two weeks at 5∘C while frozen samples were kept for up to three months at −20∘C. There were two drying treatments, one including osmotic pretreatment followed by cabinet drying and the other involving only cabinet drying. Total anthocyanins found in fresh blueberries were 7.2±0.5 mg/g dry matter, expressed as cyanidin 3-rutinoside equivalents. In comparison with fresh samples, total anthocyanins in untreated and pretreated dried blueberries were significantly reduced to 4.3±0.1 mg/g solid content, 41% loss, and 3.7±0.2 mg/g solid content, 49% loss, respectively. Osmotic treatment followed by a thermal treatment had a greater effect on anthocyanin loss than the thermal treatment alone. In contrast, the frozen samples did not show any significant decrease in anthocyanin level during three months of storage. Measurement of the antioxidant activity of anthocyanin extracts from blueberries showed there was no significant difference between fresh, dried, and frozen blueberries.

  15. The Change of Total Anthocyanins in Blueberries and Their Antioxidant Effect After Drying and Freezing

    Science.gov (United States)

    Srzednicki, George

    2004-01-01

    This study examined the effects of freezing, storage, and cabinet drying on the anthocyanin content and antioxidant activity of blueberries (Vaccinium corymbosum L). Fresh samples were stored for two weeks at 5°C while frozen samples were kept for up to three months at −20°C. There were two drying treatments, one including osmotic pretreatment followed by cabinet drying and the other involving only cabinet drying. Total anthocyanins found in fresh blueberries were 7.2 ± 0.5 mg/g dry matter, expressed as cyanidin 3-rutinoside equivalents. In comparison with fresh samples, total anthocyanins in untreated and pretreated dried blueberries were significantly reduced to 4.3 ± 0.1 mg/g solid content, 41% loss, and 3.7 ± 0.2 mg/g solid content, 49% loss, respectively. Osmotic treatment followed by a thermal treatment had a greater effect on anthocyanin loss than the thermal treatment alone. In contrast, the frozen samples did not show any significant decrease in anthocyanin level during three months of storage. Measurement of the antioxidant activity of anthocyanin extracts from blueberries showed there was no significant difference between fresh, dried, and frozen blueberries. PMID:15577185

  16. Anti-inflammatory and antinociceptive activities of Phyllanthus niruri spray-dried standardized extract

    Directory of Open Access Journals (Sweden)

    Cínthia R. C. Porto

    2013-02-01

    Full Text Available Phyllanthus niruri L., Euphorbiaceae, spray-dried standardized extract was studied for its anti-inflammatory and antinociceptive activities in adult albino rats and mice. The anti-inflammatory effect of spray-dried standardized extract was observed in carrageenan-induced paw edema and thioglycolate-induced leukocyte migration, while antinociceptive effects were observed using Randall & Selitto, tail flick, and hot plate tests. This study showed that intraperitoneal spray-dried standardized extract at 100, 200, 800, or 1600 mg/kg reduced the vascular response in the inflammatory process of paw edema induced by 1% carrageenan. Oral spray-dried standardized extract at 100 or 200 mg/kg inhibited leukocyte migration to the site of inflammation induced by 3% thioglycolate. In rats, at 100 and 200 mg/kg intraperitoneally, the extract exhibited a marked peripheral analgesic effect in a Randall & Selitto assay and showed significant central analgesic activity in a hot plate and tail flick assay. In conclusion, this study suggested that Phyllanthus niruri spray-dried standardized extract has potent inflammatory and antinociceptive activities and that these activities are not modified by standard drying process, making it feasible to use the dry extract standardized to obtain a phytotherapic preparation and thus validating its use for the treatment of pain and inflammation disorders.

  17. Obtain and characterization of chitosan / propranolol microparticles by spray drying

    International Nuclear Information System (INIS)

    Nascimento, Ednaldo G. do; Silva Junior, Arnobio A. da; Santos, Katia S.C.R. dos

    2015-01-01

    The study investigated the application of chitosan microparticles as carriers into hard gelatin capsule containing propranolol, evaluating the variability of the molecular weight and the chitosan particles by spray drying. The formulations were characterized by average weight, dosing unit dose uniformity and dissolution profile according to the pharmacopoeia. While the microparticles were characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy and X-ray diffraction. The results showed that chitosan microparticles obtained without the drug and then physically mixed with propranolol promoted a modified release 85% of the drug after 5 hours. While, chitosan microparticles sprayed with propranolol released only 55% at 5 hours is presented both as a modified release system. Samples of dried chitosan showed up amorphous and homogeneous and spherical morphology. (author)

  18. Spray Drying of High Sugar Content Foods: Improving of Product Yield and Powder Properties

    Directory of Open Access Journals (Sweden)

    Mehmet Koç

    2016-05-01

    Full Text Available Spray drying is the most preferred drying method to produce powdered food in the food industry and it is also widely used to convert sugar-rich liquid foods to a powder form. During and/or after spray drying process of sugar-rich products, undesirable situation was appeared such as stickiness, high moisture affinity (hygroscopicity and low solubility due to low molecular weight monosaccharides that found naturally in the structure. The basis of these problems was formed by low glass transition temperature of sugar-rich products. This review gives information about the difficulties in drying of sugar-rich products via spray dryer, actions need to be taken against these difficulties and drying of sugar-rich honey and fruit juices with spray drying method.

  19. Weighted network modules

    International Nuclear Information System (INIS)

    Farkas, Illes; Abel, Daniel; Palla, Gergely; Vicsek, Tamas

    2007-01-01

    The inclusion of link weights into the analysis of network properties allows a deeper insight into the (often overlapping) modular structure of real-world webs. We introduce a clustering algorithm clique percolation method with weights (CPMw) for weighted networks based on the concept of percolating k-cliques with high enough intensity. The algorithm allows overlaps between the modules. First, we give detailed analytical and numerical results about the critical point of weighted k-clique percolation on (weighted) Erdos-Renyi graphs. Then, for a scientist collaboration web and a stock correlation graph we compute three-link weight correlations and with the CPMw the weighted modules. After reshuffling link weights in both networks and computing the same quantities for the randomized control graphs as well, we show that groups of three or more strong links prefer to cluster together in both original graphs

  20. Preventing Weight Gain

    Science.gov (United States)

    ... Local Programs Related Topics Diabetes Nutrition Preventing Weight Gain Language: English (US) Español (Spanish) Recommend on Facebook ... cancer. Choosing an Eating Plan to Prevent Weight Gain So, how do you choose a healthful eating ...

  1. Power ultrasound as a pretreatment to convective drying of mulberry (Morus alba L.) leaves: Impact on drying kinetics and selected quality properties.

    Science.gov (United States)

    Tao, Yang; Wang, Ping; Wang, Yilin; Kadam, Shekhar U; Han, Yongbin; Wang, Jiandong; Zhou, Jianzhong

    2016-07-01

    The effect of ultrasound pretreatment prior to convective drying on drying kinetics and selected quality properties of mulberry leaves was investigated in this study. Ultrasound pretreatment was carried out at 25.2-117.6 W/L for 5-15 min in a continuous mode. After sonication, mulberry leaves were dried in a hot-air convective dryer at 60 °C. The results revealed that ultrasound pretreatment not only affected the weight of mulberry leaves, it also enhanced the convective drying kinetics and reduced total energy consumption. The drying kinetics was modeled using a diffusion model considering external resistance and effective diffusion coefficient De and mass transfer coefficient hm were identified. Both De and hm during convective drying increased with the increase of acoustic energy density (AED) and ultrasound duration. However, De and hm increased slowly at high AED levels. Furthermore, ultrasound pretreatment had a more profound influence on internal mass transfer resistance than on external mass transfer resistance during drying according to Sherwood numbers. Regarding the quality properties, the color, antioxidant activity and contents of several bioactive compounds of dried mulberry leaves pretreated by ultrasound at 63.0 W/L for 10 min were similar to that of mulberry leaves without any pretreatments. Overall, ultrasound pretreatment is effective to shorten the subsequent drying time of mulberry leaves without damaging the quality of final product. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. California Black Oak Drying Problems and the Bacterial Factor.

    Science.gov (United States)

    1979-01-01

    operations in Anderson area and to adjacent kilns by spacing stickers 18 inches apart and Georgia and wondered if bacterial tree drying softwood lumber at...on stickers in a weighted, volatile fatty acids which are the sapwood , and then from the outer, covered pile placed outdoors on the characteristic of...1. JT~~~ Figure 1 —Scanning electron micrographs of nonintected sapwood (A-B) and bacterially infected heartwood (C-D) from

  3. Spent fuel drying system test results (first dry-run)

    International Nuclear Information System (INIS)

    Klinger, G.S.; Oliver, B.M.; Abrefah, J.; Marschman, S.C.; MacFarlan, P.J.; Ritter, G.A.

    1998-07-01

    The water-filled K-Basins in the Hanford 100 Area have been used to store N-Reactor spent nuclear fuel (SNF) since the 1970s. Because some leaks in the basin have been detected and some of the fuel is breached due to handling damage and corrosion, efforts are underway to remove the fuel elements from wet storage. An Integrated Process Strategy (IPS) has been developed to package, dry, transport, and store these metallic uranium fuel elements in an interim storage facility on the Hanford Site. Information required to support the development of the drying processes, and the required safety analyses, is being obtained from characterization tests conducted on fuel elements removed from the K-Basins. A series of whole element drying tests (reported in separate documents, see Section 7.0) have been conducted by Pacific Northwest National Laboratory (PNNL) on several intact and damaged fuel elements recovered from both the K-East and K-West Basins. This report documents the results of the first dry-run test, which was conducted without a fuel element. The empty test apparatus was subjected to a combination of low- and high-temperature vacuum drying treatments that were intended to mimic, wherever possible, the fuel treatment strategies of the IPS. The data from this dry-run test can serve as a baseline for the first two fuel element tests, 1990 (Run 1) and 3128W (Run 2). The purpose of this dry-run was to establish the background levels of hydrogen in the system, and the hydrogen generation and release characteristics attributable to the test system without a fuel element present. This test also serves to establish the background levels of water in the system and the water release characteristics. The system used for the drying test series was the Whole Element Furnace Testing System, described in Section 2.0, which is located in the Postirradiation Testing Laboratory (PTL, 327 Building). The test conditions and methodology are given in section 3.0, and the experimental

  4. Weight management in pregnancy

    OpenAIRE

    Olander, E. K.

    2015-01-01

    Key learning points:\\ud - Women who start pregnancy in an overweight or obese weight category have increased health risks\\ud - Irrespective of pre-pregnancy weight category, there are health risks associated with gaining too much weight in pregnancy for both mother and baby\\ud - There are currently no official weight gain guidelines for pregnancy in the UK, thus focus needs to be on supporting pregnant women to eat healthily and keep active

  5. Impact of daily consumption of Moringa ( Moringa oleifera ) dry leaf ...

    African Journals Online (AJOL)

    A randomized study was conducted to test the efficacy of Moringa powder on iron status and weight gain in women. In an open-labelled randomized trial, 82 moderately anaemic, lactating women, aged 26.7 6.5 years, received a weekly dose of either 100g of Moringa powder(Moringa group) or 120 mg iron sulphate with ...

  6. Use of a continuous twin screw granulation and drying system during formulation development and process optimization.

    Science.gov (United States)

    Vercruysse, J; Peeters, E; Fonteyne, M; Cappuyns, P; Delaet, U; Van Assche, I; De Beer, T; Remon, J P; Vervaet, C

    2015-01-01

    Since small scale is key for successful introduction of continuous techniques in the pharmaceutical industry to allow its use during formulation development and process optimization, it is essential to determine whether the product quality is similar when small quantities of materials are processed compared to the continuous processing of larger quantities. Therefore, the aim of this study was to investigate whether material processed in a single cell of the six-segmented fluid bed dryer of the ConsiGma™-25 system (a continuous twin screw granulation and drying system introduced by GEA Pharma Systems, Collette™, Wommelgem, Belgium) is predictive of granule and tablet quality during full-scale manufacturing when all drying cells are filled. Furthermore, the performance of the ConsiGma™-1 system (a mobile laboratory unit) was evaluated and compared to the ConsiGma™-25 system. A premix of two active ingredients, powdered cellulose, maize starch, pregelatinized starch and sodium starch glycolate was granulated with distilled water. After drying and milling (1000 μm, 800 rpm), granules were blended with magnesium stearate and compressed using a Modul™ P tablet press (tablet weight: 430 mg, main compression force: 12 kN). Single cell experiments using the ConsiGma™-25 system and ConsiGma™-1 system were performed in triplicate. Additionally, a 1h continuous run using the ConsiGma™-25 system was executed. Process outcomes (torque, barrel wall temperature, product temperature during drying) and granule (residual moisture content, particle size distribution, bulk and tapped density, hausner ratio, friability) as well as tablet (hardness, friability, disintegration time and dissolution) quality attributes were evaluated. By performing a 1h continuous run, it was detected that a stabilization period was needed for torque and barrel wall temperature due to initial layering of the screws and the screw chamber walls with material. Consequently, slightly deviating

  7. Influence of Ripeness and Drying Process on the Polyphenols and Tocopherols of Pistacia vera L.

    Directory of Open Access Journals (Sweden)

    Gabriele Ballistreri

    2009-10-01

    Full Text Available This paper highlights, for the first time, the changes in the phenolics fraction (anthocyanins, flavonoids and stilbenes and tocopherols of unpeeled Pistacia vera L. var. bianca with ripening, and the effect of the sun-drying process. The total polyphenol levels in pistachios, measured as mg of Gallic Acid Equivalent (GAE, were: 201 ± 10.1, 349 ± 18.3 and 184.7 ± 6.2 mg GAE/100 g DM in unripe, ripe and dried ripe samples, respectively. Most phenolics in ripe pistachios were found to be anthocyanins. They increased with ripening, while the sun drying process caused a susbtantial loss. Flavonoids found in all pistachio samples were daidzein, genistein, daidzin, quercetin, eriodictyol, luteolin, genistin and naringenin, which decreased both with ripening and drying. Before the drying process both unripe and ripe pistachios showed a higher content of trans-resveratrol than dried ripe samples. γ-Tocopherol was the major vitamin E isomer found in pistachios. The total content (of α- and γ-tocopherols decreased, both during ripening and during the drying process. These results suggested that unpeeled pistachios can be considered an important source of phenolics, particularly of anthocyanins. Moreover, in order to preserve these healthy characteristics, new and more efficient drying processes should be adopted.

  8. Treatment of Dry Eye Disease.

    Science.gov (United States)

    Marshall, Leisa L; Roach, J Michael

    2016-02-01

    Review of the etiology, clinical manifestations, and treatment of dry eye disease (DED). Articles indexed in PubMed (National Library of Medicine), Iowa Drug Information Service (IDIS), and the Cochrane Reviews and Trials in the last 10 years using the key words "dry eye disease," "dry eye syndrome," "dry eye and treatment." Primary sources were used to locate additional resources. Sixty-eight publications were reviewed, and criteria supporting the primary objective were used to identify useful resources. The literature included practice guidelines, book chapters, review articles, original research articles, and product prescribing information for the etiology, clinical manifestations, diagnosis, and treatment of DED. DED is one of the most common ophthalmic disorders. Signs and symptoms of DED vary by patient, but may include ocular irritation, redness, itching, photosensitivity, visual blurring, mucous discharge, and decreased tear meniscus or break-up time. Symptoms improve with treatment, but the condition is not completely curable. Treatment includes reducing environmental causes, discontinuing medications that cause or worsen dry eye, and managing contributing ocular or systemic conditions. Most patients use nonprescription tear substitutes, and if these are not sufficient, other treatment is prescribed. These treatments include the ophthalmic anti-inflammatory agent cyclosporine, punctal occlusion, eye side shields, systemic cholinergic agents, and autologous serum tears. This article reviews the etiology, symptoms, and current therapy for DED.

  9. Alterations of Mg2+ After Hemorrhagic Shock.

    Science.gov (United States)

    Lee, Mun-Young; Yang, Dong Kwon; Kim, Shang-Jin

    2017-11-01

    Hemorrhagic shock is generally characterized by hemodynamic instability with cellular hypoxia and diminishing cellular function, resulting from an imbalance between systemic oxygen delivery and consumption and redistribution of fluid and electrolytes. Magnesium (Mg) is the fourth most abundant cation overall and second most abundant intracellular cation in the body and an essential cofactor for the energy production and cellular metabolism. Data for blood total Mg (tMg; free-ionized, protein-bound, and anion-bound forms) and free Mg 2+ levels after a traumatic injury are inconsistent and only limited information is available on hemorrhagic effects on free Mg 2+ as the physiologically active form. The aim of this study was to determine changes in blood Mg 2+ and tMg after hemorrhage in rats identifying mechanism and origin of the changes in blood Mg 2+ . Hemorrhagic shock produced significant increases in blood Mg 2+ , plasma tMg, Na + , K + , Cl - , anion gap, partial pressures of oxygen, glucose, and blood urea nitrogen but significant decreases in RBC tMg, blood Ca 2+ , HCO 3 - , pH, partial pressures of carbon dioxide, hematocrit, hemoglobin, total cholesterol, and plasma/RBC ATP. During hemorrhagic shock, K + , anion gap, and BUN showed significant positive correlations with changes in blood Mg 2+ level, while Ca 2+ , pH, and T-CHO correlated to Mg 2+ in a negative manner. In conclusion, hemorrhagic shock induced an increase in both blood-free Mg 2+ and tMg, resulted from Mg 2+ efflux from metabolic damaged cell with acidosis and ATP depletion.

  10. Gradient Weight in Phonology

    Science.gov (United States)

    Ryan, Kevin Michael

    2011-01-01

    Research on syllable weight in generative phonology has focused almost exclusively on systems in which weight is treated as an ordinal hierarchy of clearly delineated categories (e.g. light and heavy). As I discuss, canonical weight-sensitive phenomena in phonology, including quantitative meter and quantity-sensitive stress, can also treat weight…

  11. Gestational weight gain.

    Science.gov (United States)

    Kominiarek, Michelle A; Peaceman, Alan M

    2017-12-01

    Prenatal care providers are advised to evaluate maternal weight at each regularly scheduled prenatal visit, monitor progress toward meeting weight gain goals, and provide individualized counseling if significant deviations from a woman's goals occur. Today, nearly 50% of women exceed their weight gain goals with overweight and obese women having the highest prevalence of excessive weight gain. Risks of inadequate weight gain include low birthweight and failure to initiate breast-feeding whereas the risks of excessive weight gain include cesarean deliveries and postpartum weight retention for the mother and large-for-gestational-age infants, macrosomia, and childhood overweight or obesity for the offspring. Prenatal care providers have many resources and tools to incorporate weight and other health behavior counseling into routine prenatal practices. Because many women are motivated to improve health behaviors, pregnancy is often considered the optimal time to intervene for issues related to eating habits and physical activity to prevent excessive weight gain. Gestational weight gain is a potentially modifiable risk factor for a number of adverse maternal and neonatal outcomes and meta-analyses of randomized controlled trials report that diet or exercise interventions during pregnancy can help reduce excessive weight gain. However, health behavior interventions for gestational weight gain have not significantly improved other maternal and neonatal outcomes and have limited effectiveness in overweight and obese women. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. In vivo and in vitro addition of dried olive extract in poultry.

    Science.gov (United States)

    King, Annie J; Griffin, Johanna K; Roslan, Fahkirah

    2014-08-06

    A freeze-dried powder from organic olive (Olea europaea) juice extract, contains 8.82% polyphenols and a minimum of 2.5% hydroxytyrosol (3,4-dihydroxyphenylethanol), an effective free radical scavenger and the major antioxidant in the byproduct (dried olive extract, DOE). Myricetin, a bioflavonoid extract from the bark powder of the bayberry tree (Myrica cerifera), also has many beneficial biological properties and antioxidative capacity. While well-known as antioxidants, the capacity of these compounds to retard lipid oxidation in foods containing unsaturated fatty acids has not been widely evaluated. Thus, a study was conducted to assess the capacity of DOE to (1) enhance the growth of poultry, (2) determine the effectiveness of DOE (administered in vivo) as an antioxidant in post-mortem tissue and further processed meat, and (3) compare the in vitro antioxidative capacity of hydroxytyrosol and myricetin. DOE was administered ad libitum in water at 6 and 12 mg per bird per day for 6 weeks in a factorial design: 3 diets (control plus two treatment levels) × 2 blocks × 2 replications. There was no enhancement of feed consumption, body weight (BW), or feed conversion by DOE; overall means for these measurements were 5.49 kg per bird, 3.32 kg per bird, and 1.65 g feed per g live BW, respectively. Diagnostic examinations of two birds per pen at the end of the study revealed no adverse effects due to consumption of DOE, a generally recognized as safe substance. The byproduct, administered in vivo, did not retard lipid oxidation in fresh, heated, or NaCl (1.0% w/w)/heated/stored meat as assessed by absorbance values for thiobarbituric acid reactive substances at 532 nm and 2,2-diphenylpicrylhydrazyl at 517 nm. Both the byproduct and hydroxytyrosol are highly water-soluble and may have been unavailable as an antioxidant in the tissue of broilers that did not consume water for 4-6 h prior to processing. As an additive in processed thigh meat, 6 and 12 mg of DOE (2

  13. Modeling and stabilities of Mg/MgH2 interfaces: A first-principles investigation

    Directory of Open Access Journals (Sweden)

    Jia-Jun Tang

    2014-07-01

    Full Text Available We have theoretically investigated the modeling and the structural stabilities of various Mg/MgH2 interfaces, i.e. Mg(101¯0/MgH2(210, Mg(0001/MgH2(101 and Mg(101¯0/MgH2(101, and provided illuminating insights into Mg/MgH2 interface. Specifically, the main factors, which impact the interfacial energies, are fully considered, including surface energies of two phases, mutual lattice constants of interface model, and relative position of two phases. The surface energies of Mg and MgH2, on the one hand, are found to be greatly impacting the interfacial energies, reflected by the lowest interfacial energy of Mg(0001/MgH2(101 which is comprised of two lowest energy surfaces. On the other hand, it is demonstrated that the mutual lattice constants and the relative position of two phases lead to variations of interfacial energies, thus influencing the interface stabilities dramatically. Moreover, the Mg-H bonding at interface is found to be the determinant of Mg/MgH2 interface stability. Lastly, interfacial and strain effects on defect formations are also studied, both of which are highly facilitating the defect formations. Our results provide a detailed insight into Mg/MgH2 interface structures and the corresponding stabilities.

  14. Serum biochemical activities and muscular soreness in transported goats administered with ascorbic acid during the hot-dry season

    Directory of Open Access Journals (Sweden)

    Ndazo S Minka

    2010-12-01

    Full Text Available The effects of handling, loading and 12 h of road transportation during the hot-dry season on muscular metabolism of 20 experimental goats administered orally with 100 mg/kg body weight of ascorbic acid (AA dissolved in 10 ml of sterile water, and other 20 control goats given equivalent of sterile water 40 min prior to transportation were investigated. The result obtained post-transportation showed that handling, loading and transportation were stressful to the goats, especially the control goats and resulted into muscular damage and the development of delayed-onset-muscular-soreness (DOMS, which may lead to dark-firm-dry (DFD syndrome meat with undesirable effects on its quality. In the experimental goats administered AA such transportation effects were minimal or completely abolished. The result demonstrated that AA reduced the incidence of DOMS and muscular damage in transported goats, therefore it may be used to improve the welfare and quality of meat obtained from goats subjected to long period of road transportation under adverse climatic conditions.

  15. Tropical savannas and dry forests.

    Science.gov (United States)

    Pennington, R Toby; Lehmann, Caroline E R; Rowland, Lucy M

    2018-05-07

    In the tropics, research, conservation and public attention focus on rain forests, but this neglects that half of the global tropics have a seasonally dry climate. These regions are home to dry forests and savannas (Figures 1 and 2), and are the focus of this Primer. The attention given to rain forests is understandable. Their high species diversity, sheer stature and luxuriance thrill biologists today as much as they did the first explorers in the Age of Discovery. Although dry forest and savanna may make less of a first impression, they support a fascinating diversity of plant strategies to cope with stress and disturbance including fire, drought and herbivory. Savannas played a fundamental role in human evolution, and across Africa and India they support iconic megafauna. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Dry Fruits and Diabetes Mellitus

    Directory of Open Access Journals (Sweden)

    Khan Sohaib A

    2017-04-01

    Full Text Available Dry fruits are some of the essential foods a human body requires staying healthy. They are made after extracting water from them. These fruits are full of essential nutrients including minerals, vitamins, enzymes, fibers and protect the body from a number of different adversities. These fruits are also a source of healthy nutrition among diabetic people who are very concerned about what to eat and what not to eat. But besides their countless benefits, these dry fruits can cause a number of harms to the body and therefore, must be used in a balanced way. This article is based on healthy and unhealthy effects of dry fruits and their use in diabetes mellitus.

  17. Ageing of Dry Cement Mixes for Finishing Purposes

    Directory of Open Access Journals (Sweden)

    Bronius VEKTARIS

    2013-09-01

    Full Text Available Dry building mixes, stored in the air, absorb water vapor and CO2 gas and ageing because properties of binding materials, mostly Portland cement, deteriorate after its prehydration and carbonation. In this paper the ageing singularities of dry cement mixes for finishing purposes and additives for retarding this process has been determinated. Ordinary and quickly hardening Portland cements absorb H2O and CO2 more than white cement – about 70 % – 75 % and 30 % – 38 % per month of innitial mass, respectively. White cement is more resistant to prehydration and carbonation, because it contains less C3A, C4AF and alkali, characterized initial activity. Dry mixes with white cement, although slower, but still worse after stored. Influence of routine dry mortar mixes ingredients and additives (methyl cellulose, pigments, sand and lime on prehydration properties of the mixes for finishing purpose is not substantial. Significant positive influence comes from the addition of fatty acid salts (zinc stearate or sodium oleate. The dry cement mixes for finishing purpose has been recomended to hydrophobisate with one of these additives, adding about 1 % by weight of cement during preducing mixes. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.5243

  18. Ageing of Dry Cement Mixes for Finishing Purposes

    Directory of Open Access Journals (Sweden)

    Bronius VEKTARIS

    2013-09-01

    Full Text Available Dry building mixes, stored in the air, absorb water vapor and CO2 gas and ageing because properties of binding materials, mostly Portland cement, deteriorate after its prehydration and carbonation. In this paper the ageing singularities of dry cement mixes for finishing purposes and additives for retarding this process has been determinated. Ordinary and quickly hardening Portland cements absorb H2O and CO2 more than white cement – about 70 % – 75 % and 30 % – 38 % per month of innitial mass, respectively. White cement is more resistant to prehydration and carbonation, because it contains less C3A, C4AF and alkali, characterized initial activity. Dry mixes with white cement, although slower, but still worse after stored. Influence of routine dry mortar mixes ingredients and additives (methyl cellulose, pigments, sand and lime on prehydration properties of the mixes for finishing purpose is not substantial. Significant positive influence comes from the addition of fatty acid salts (zinc stearate or sodium oleate. The dry cement mixes for finishing purpose has been recomended to hydrophobisate with one of these additives, adding about 1 % by weight of cement during preducing mixes. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.5243

  19. Freeze-dried microarterial allografts

    International Nuclear Information System (INIS)

    Raman, J.; Hargrave, J.C.

    1990-01-01

    Rehydrated freeze-dried microarterial allografts were implanted to bridge arterial defects using New Zealand White rabbits as the experimental model. Segments of artery from the rabbit ear and thigh were harvested and preserved for a minimum of 2 weeks after freeze-drying. These allografts, approximately 1 mm in diameter and ranging from 1.5 to 2.5 cm in length, were rehydrated and then implanted in low-pressure and high-pressure arterial systems. Poor patency was noted in low-pressure systems in both allografts and autografts, tested in 12 rabbits. In the high-pressure arterial systems, allografts that were freeze-dried and reconstituted failed in a group of 10 rabbits with an 8-week patency rate of 30 percent. Gamma irradiation in an effort to reduce infection and antigenicity of grafts after freeze-drying was associated with a patency rate of 10 percent at 8 weeks in this system in another group of 10 rabbits. Postoperative cyclosporin A therapy was associated with a patency rate of 22.2 percent in the high-pressure arterial system in a 9-rabbit group. Control autografts in this system in a group of 10 rabbits showed a 100 percent patency at 8 weeks. Microarterial grafts depend on perfusion pressure of the vascular bed for long-term patency. Rehydrated freeze-dried microarterial allografts do not seem to function well in lengths of 1 to 2.5 cm when implanted in a high-pressure arterial system. Freeze-dried arterial allografts are probably not antigenic

  20. Selected chemical compounds in firm and mellow persimmon fruit before and after the drying process.

    Science.gov (United States)

    Senica, Mateja; Veberic, Robert; Grabnar, Jana Jurhar; Stampar, Franci; Jakopic, Jerneja

    2016-07-01

    Persimmon is a seasonal fruit and only available in fresh form for a short period of each year. In addition to freezing, drying is the simplest substitute for the fresh fruit and accessible throughout the year. The effect of mellowing and drying was evaluated in 'Tipo' persimmon, an astringent cultivar. 'Tipo' firm fruit contained high levels of tannins (1.1 mg g(-1) DW), which were naturally decreased to 0.2 mg g(-1) DW after mellowing. The drying process greatly impacted the contents of carotenoids, total phenols, individual phenolics, tannins, organic acids, sugars and colour parameters in firm and mellow fruit. The reduction of tannins, phenolic compounds and organic acids were accompanied by the increase of sugars and carotenoids, improving the colour of the analysed samples. These results showed that the drying process improved the quality of persimmon products and extended their shelf life. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

  1. The synthesis and characterization of Mg-Zn-Ca alloy by powder metallurgy process

    Energy Technology Data Exchange (ETDEWEB)

    Annur, Dhyah; Franciska, P.L.; Erryani, Aprilia; Amal, M. Ikhlasul; Kartika, Ika, E-mail: pepeng2000@yahoo.com [Research center for Metallurgy and Material, Indonesian Institute of Science (Indonesia); Sitorus, Lyandra S. [Sultan Ageng Tirtayasa University (Indonesia)

    2016-04-19

    Known for its biodegradation and biocompatible properties, magnesium alloys have gained many interests to be researched as implant material. In this study, Mg-3Zn-1Ca, Mg-29Zn-1Ca, and Mg-53Zn-4.3Ca (in wt%) were synthesized by means of powder metallurgy method. The compression strength and corrosion resistance of magnesium alloy were thoroughly examined. The microstructures of the alloy were characterized using optical microscopy, Scanning Electron Microscope, and also X-ray diffraction analysis. The corrosion resistance were evaluated using electrochemical analysis. The result indicated that Mg- Zn- Ca alloy could be synthesized using powder metallurgy method. This study showed that Mg-29Zn-1Ca would make the highest mechanical strength up to 159.81 MPa. Strengthening mechanism can be explained by precipitation hardening and grain refinement mechanism. Phase analysis had shown the formation of α Mg, MgO, and intermetallic phases: Mg2Zn11 and also Ca2Mg6Zn3. However, when the composition of Zn reach 53% weight, the mechanical strength will be decreasing. In addition, all of Mg-Zn-Ca alloy studied here had better corrosion resistance (Ecorr around -1.4 VSCE) than previous study of Mg. This study indicated that Mg- 29Zn- 1Ca alloy can be further analyzed to be a biodegradable implant material.

  2. Foam-mat drying technology: A review.

    Science.gov (United States)

    Hardy, Z; Jideani, V A

    2017-08-13

    This article reviews various aspects of foam-mat drying such as foam-mat drying processing technique, main additives used for foam-mat drying, foam-mat drying of liquid and solid foods, quality characteristics of foam-mat dried foods, and economic and technical benefits for employing foam-mat drying. Foam-mat drying process is an alternative method that allows the removal of water from liquid materials and pureed materials. In this drying process, a liquid material is converted into foam that is stable by being whipped after adding an edible foaming agent. The stable foam is then spread out in sheet or mat and dried by using hot air (40-90°C) at atmospheric pressure. Methyl cellulose (0.25-2%), egg white (3-20%), maltodextrin (0.5-05%), and gum Arabic (2-9%) are the commonly utilized additives for the foam-mat drying process at the given range, either combined together for their effectiveness or individual effect. The foam-mat drying process is suitable for heat sensitive, viscous, and sticky products that cannot be dried using other forms of drying methods such as spray drying because of the state of product. More interest has developed for foam-mat drying because of the simplicity, cost effectiveness, high speed drying, and improved product quality it provides.

  3. 7 CFR 58.813 - Dry whey.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Dry whey. 58.813 Section 58.813 Agriculture... Products Bearing Usda Official Identification § 58.813 Dry whey. The quality requirements for dry whey shall be in accordance with the U.S. Standards for Dry Whey. Supplemental Specifications for Plants...

  4. Economics of dry storage systems

    International Nuclear Information System (INIS)

    Moore, G.R.; Winders, R.C.

    1980-01-01

    This paper postulates a dry storage application suitable as a regional away-from-reactor storage (AFR), develops an economical system design concept and estimates system costs. The system discussed uses the experience gained in the dry storage research activities and attempts to present a best foot forward system concept. The major element of the system is the Receiving and Packaging Building. In this building fuel assemblies are removed from transportation casks and encapsulated for storage. This facility could be equally applicable to silo, vault, or caisson storage. However the caisson storage concept has been chosen for discussion purposes

  5. Thyroid weight with age

    International Nuclear Information System (INIS)

    Raulier-Fabry, C.; Hammer, R.

    1965-01-01

    A large number of data on thyroid weight of euthyroid subjects have been collected from the literature in this study. The most probable average weight of the gland appears to be 20 g in the adult and 2 g in the newborn. A decrease in weight has been observed during the first year of life (1 g at 6 months) and only in the second year of life the initial birth weight is reached again. The weight curve may be considered as consisting of three straight lines: from 2 to 7, from 7 to 18 and from 18 to 25 years, their slopes being respectively 0.6, 0.9 and 0.5 g/year. The variations in weight of the thyroid during adulthood are sufficiently small to consider it as having constant value between 25 and 55 years. The available information points to a negligible weight difference between sexes. (authors) [fr

  6. Drying properties and quality parameters of dill dried with intermittent and continuous microwave

    OpenAIRE

    Eştürk, Okan

    2012-01-01

    In this study, influence of various microwave-convective air drying applications on drying kinetics, color and sensory quality of dill leaves (Anethum graveolens L.) were investigated. In general, increasing the drying air temperature decreased the drying time, and increased the drying rate. Increasing microwave pulse ratio increased the drying time. Page, Logarithmic, Midilli et al, Wang & Singh and Logistic models were fitted to drying data and the Page model was found to satisfactorily...

  7. Kinetics, mass transport characteristics, and structural changes during air-drying of purple yam (Dioscorea Alata L.) at different process conditions

    Science.gov (United States)

    De Vera, Flordeliza C.; Comaling, Leif Anthony B.; Lao, Iya Ray Alyanna M.; Caparanga, Alvin R.; Sauli, Zaliman

    2017-11-01

    This experiment was designed to follow the 2k factorial design to study the effects of the three drying parameters on the drying characteristics and effective moisture diffusivity and to fit each run performed on the best thin-layer drying kinetics model. Raw purple yam samples were pre-treated and undergone the designed drying procedures at which the weight of the samples were recorded every minute until such time that the sample weights become constant. Scanning Electron Microscopy (SEM) is utilized for qualitative analysis of the dried samples. The number of pores per unit area and the overall aesthetics of the surface of the dried samples were compared also using SEM. Considering the qualitative analysis conducted on the samples from the images of SEM, dried samples from run 2 has the most desirable conditions such as high temperature and low air velocity for drying because the samples from this run have large pore diameters with minimal cell breakages.

  8. Yogurt and weight management.

    Science.gov (United States)

    Jacques, Paul F; Wang, Huifen

    2014-05-01

    A large body of observational studies and randomized controlled trials (RCTs) has examined the role of dairy products in weight loss and maintenance of healthy weight. Yogurt is a dairy product that is generally very similar to milk, but it also has some unique properties that may enhance its possible role in weight maintenance. This review summarizes the human RCT and prospective observational evidence on the relation of yogurt consumption to the management and maintenance of body weight and composition. The RCT evidence is limited to 2 small, short-term, energy-restricted trials. They both showed greater weight losses with yogurt interventions, but the difference between the yogurt intervention and the control diet was only significant in one of these trials. There are 5 prospective observational studies that have examined the association between yogurt and weight gain. The results of these studies are equivocal. Two of these studies reported that individuals with higher yogurt consumption gained less weight over time. One of these same studies also considered changes in waist circumference (WC) and showed that higher yogurt consumption was associated with smaller increases in WC. A third study was inconclusive because of low statistical power. A fourth study observed no association between changes in yogurt intake and weight gain, but the results suggested that those with the largest increases in yogurt intake during the study also had the highest increase in WC. The final study examined weight and WC change separately by sex and baseline weight status and showed benefits for both weight and WC changes for higher yogurt consumption in overweight men, but it also found that higher yogurt consumption in normal-weight women was associated with a greater increase in weight over follow-up. Potential underlying mechanisms for the action of yogurt on weight are briefly discussed.

  9. Characterization of wet and dry deposition in the downwind of industrial sources in a dry tropical area.

    Science.gov (United States)

    Singh, R K; Agrawal, M

    2001-12-19

    An atmospheric deposition study was conducted in the downwind of Shaktinagar Thermal Power Plant (STPP), Renusagar Thermal Power Plant (RTPP), and Anpara Thermal Power Plant (ATPP), at Singrauli region, Uttar Pradesh (UP), India to characterize dry and wet deposition in relation to different pollution loading. During the study period, dry and wet depositions and levels of gaseous pollutants (SO2 and NO2) were estimated across the sites. Dry deposition was collected on a monthly basis and wet deposition on an event basis. Depositions were analyzed for pH, nitrate (NO3-), ammonium (NH4+), and sulphate (SO4(2-)) contents. Dry deposition rate both collected as clearfall and throughfall varied between 0.15 to 2.28 and 0.33 to 3.48 g m(-2) day(-1), respectively, at control and maximally polluted sites. The pH of dry deposition varied from 5.81 to 6.89 during winter and 6.09 to 7.02 during summer across the sites. During the rainy season, the mean pH of clear wet deposition varied from 6.56 to 7.04 and throughfall varied from 6.81 to 7.22. The concentrations of NO2 and SO2 pollutants were highest during the winter season. Mean SO2 concentrations varied from 18 to 75 g m(-3) at control and differently polluted sites during the winter season. The variation in NO2 concentrations did not show a pattern similar to that of SO2. The highest NO2 concentration during the winter season was 50 g m(-3), observed near RTPP. NO2 concentration did not show much variation among different sites, suggesting that the sources of NO2 emission are evenly distributed along the sites. The concentrations of NH4+, NO3-, and SO4(2-) ions in dry deposition were found to be higher in summer as compared to the winter season. In dry deposition (clearfall) the concentrations of NH4+, NO3-, and SO4(2-) varied from 0.13 to 1.0, 0.81 to 1.95, and 0.82 to 3.27 mg l(-1), respectively, during winter. In wet deposition (clearfall), the above varied from 0.14 to 0.74, 0.81 to 1.82, and 0.67 to 2.70 mg l(-1

  10. The use of distillers dried grains plus solubles as a feed ingredient on air emissions and performance from laying hens.

    Science.gov (United States)

    Wu-Haan, W; Powers, W; Angel, R; Applegate, T J

    2010-07-01

    The objectives of the current study were to evaluate the effect of feeding diets containing 0, 10, or 20% distillers dried grains plus solubles (DDGS) to laying hens (21 to 26 wk of age) on emissions of NH3 and H2S. Hy-Line W-36 hens (n = 640) were allocated randomly to 8 environmental rooms for a 5-wk period (hens in 3 rooms were offered the 10% and 20% DDGS diets each; hens in 2 rooms were offered the 0% DDGS diet). Diets were formulated to contain similar CP levels (18.3%), nonphytate P (0.46%), and Ca (4.2%). On an analyzed basis, the 0, 10, and 20% DDGS diets contained 0.22, 0.27, and 0.42% S. Egg weight (50.9 g), egg production (85%), and feed intake (87.9 g/hen per d) were unaffected by diet (P > 0.05) over the study period. Daily NH3 emissions from hens fed diets containing 0, 10, and 20% DDGS were 105.4, 91.7, and 80.2 mg/g of N consumed, respectively (P hens fed commercial diets containing 0, 10, and 20% DDGS were 2.6, 2.4, and 1.1 mg/g of S consumed, respectively. Overall, feeding 21- to 26-wk-old laying hens diets containing 20% DDGS decreased daily NH3 emissions by 24% and H2S emissions by 58%. Each hen emitted approximately 280 mg of NH3 and 0.5 mg of H2S daily when fed a control diet containing 18% CP and 0.2% S. The results of this study demonstrate that 20% DDGS derived from ethanol production can be fed to laying hens, resulting in lower emissions of NH3 and H2S with no apparent adverse effects on hen performance.

  11. Blades Couple Dry Friction Connection

    Czech Academy of Sciences Publication Activity Database

    Půst, Ladislav; Pešek, Luděk; Radolfová, Alena

    2015-01-01

    Roč. 9, č. 1 (2015), s. 31-40 ISSN 1802-680X Institutional support: RVO:61388998 Keywords : stick-slip dry friction * 3D friction characteristic * tangential contact stiffness * hysterezis loop * response curves Subject RIV: BI - Acoustics

  12. THE DIRT ON DRY MERGERS

    International Nuclear Information System (INIS)

    Desai, Vandana; Soifer, B. T.; Dey, Arjun; Cohen, Emma; Le Floc'h, Emeric

    2011-01-01

    Using data from the Spitzer Space Telescope, we analyze the mid-infrared (3-70 μm) spectral energy distributions of dry merger candidates in the Booetes field of the NOAO Deep Wide-Field Survey. These candidates were selected by previous authors to be luminous, red, early-type galaxies with morphological evidence of recent tidal interactions. We find that a significant fraction of these candidates exhibit 8 and 24 μm excesses compared to expectations for old stellar populations. We estimate that a quarter of dry merger candidates have mid-infrared-derived star formation rates greater than ∼1 M sun yr -1 . This represents a 'frosting' on top of a large old stellar population, and has been seen in previous studies of elliptical galaxies. Further, the dry merger candidates include a higher fraction of star-forming galaxies relative to a control sample without tidal features. We therefore conclude that the star formation in these massive ellipticals is likely triggered by merger activity. Our data suggest that the mergers responsible for the observed tidal features were not completely dry, and may be minor mergers involving a gas-rich dwarf galaxy.

  13. DRY TRANSFER FACILITY SEISMIC ANALYSIS

    International Nuclear Information System (INIS)

    EARNEST, S.; KO, H.; DOCKERY, W.; PERNISI, R.

    2004-01-01

    The purpose of this calculation is to perform a dynamic and static analysis on the Dry Transfer Facility, and to determine the response spectra seismic forces for the design basis ground motions. The resulting seismic forces and accelerations will be used in a subsequent calculation to complete preliminary design of the concrete shear walls, diaphragms, and basemat

  14. Dry technologies and community bureaucracies

    DEFF Research Database (Denmark)

    Rasmussen, Mattias Borg

    2014-01-01

    Irrigation channels criss-cross the Andes, bringing water to the dry soils of the peasants' fields. To obtain water, people must deal not only with the amount of water and the physical terrain, but also with concerns of others and matters of the social terrain....

  15. Dry spent fuel storage licensing

    International Nuclear Information System (INIS)

    Sturz, F.C.

    1995-01-01

    In the US, at-reactor-site dry spent fuel storage in independent spent fuel storage installations (ISFSI) has become the principal option for utilities needing storage capacity outside of the reactor spent fuel pools. Delays in the geologic repository operational date at or beyond 2010, and the increasing uncertainty of the US Department of Energy's (DOE) being able to site and license a Monitored Retrievable Storage (MRS) facility by 1998 make at-reactor-site dry storage of spent nuclear fuel increasingly desirable to utilities and DOE to meet the need for additional spent fuel storage capacity until disposal, in a repository, is available. The past year has been another busy year for dry spent fuel storage licensing. The licensing staff has been reviewing 7 applications and 12 amendment requests, as well as participating in inspection-related activities. The authors have licensed, on a site-specific basis, a variety of dry technologies (cask, module, and vault). By using certified designs, site-specific licensing is no longer required. Another new cask has been certified. They have received one new application for cask certification and two amendments to a certified cask design. As they stand on the brink of receiving multiple applications from DOE for the MPC, they are preparing to meet the needs of this national program. With the range of technical and licensing options available to utilities, the authors believe that utilities can meet their need for additional spent fuel storage capacity for essentially all reactor sites through the next decade

  16. Apparatus for drying sugar cubes

    NARCIS (Netherlands)

    Derckx, H.A.J.; Torringa, H.M.

    1999-01-01

    Device for drying sugar cubes containing a heating apparatus for heating and dehumidifying the sugar cubes, a conditioning apparatus for cooling off and possibly further dehumidifying the sugar cubes and a conveying apparatus for conveying the sugar cubes through the heating apparatus and the

  17. Some Physics Inside Drying Droplets

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 19; Issue 2. Some Physics Inside Drying Droplets. Dileep Mampallil. General Article Volume 19 Issue 2 February 2014 pp 123-134. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/019/02/0123-0134 ...

  18. Fluidization of Dried Wastewater Sludge.

    Czech Academy of Sciences Publication Activity Database

    Hartman, Miloslav; Pohořelý, Michael; Trnka, Otakar

    2007-01-01

    Roč. 178, 3 (2007) , s. 166-172 ISSN 0032-5910 R&D Projects: GA AV ČR(CZ) IAA4072201 Institutional research plan: CEZ:AV0Z40720504 Keywords : fluidization characteristics * multiphase reactors * dried stabilized wastewater sludge Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.130, year: 2007

  19. Dry release of suspended nanostructures

    DEFF Research Database (Denmark)

    Forsén, Esko Sebastian; Davis, Zachary James; Dong, M.

    2004-01-01

    , the technique enables long time storage and transportation of produced devices without the risk of stiction. By combining the dry release method with a plasma deposited anti-stiction coating both fabrication induced stiction, which is mainly caused by capillary forces originating from the dehydration...

  20. Flavour release from dried vegetables

    NARCIS (Netherlands)

    Ruth, van S.M.

    1995-01-01

    The research described in this thesis was focused on the development of an in vitro model system for isolation of volatile compounds from dried vegetables under mouth conditions, such as volume of the mouth, temperature, salivation and mastication. Instrumental analysis of these

  1. Formulation development of the biocontrol agent Bacillus subtilis strain CPA-8 by spray-drying.

    Science.gov (United States)

    Yánez-Mendizábal, V; Viñas, I; Usall, J; Torres, R; Solsona, C; Abadias, M; Teixidó, N

    2012-05-01

    To prepare commercially acceptable formulations of Bacillus subtilis CPA-8 by spray-drying with long storage life and retained efficacy to control peach and nectarine brown rot caused by Monilinia spp. CPA-8 24-h- and 72-h-old cultures were spray dried using 10% skimmed milk, 10% skimmed milk plus 10% MgSO(4) , 10% MgSO(4) and 20% MgSO(4) as carriers/protectants. All carriers/protectants gave good percentages of powder recovery (28-38%) and moisture content (7-13%). CPA-8 survival varied considerably among spray-dried 24-h- and 72-h-old cultures. Seventy-two hours culture spray dried formulations showed the highest survival (28-32%) with final concentration products of 1·6-3·3 × 10(9) CFU g(-1) , while viability of 24-h-old formulations was lower than 1%. Spray-dried 72-h-old formulations were selected to subsequent evaluation. Rehydration of cells with water provided a good recovery of CPA-8 dried cells, similar to other complex rehydration media tested. Spray-dried formulations stored at 4 ± 1 and 20 ± 1°C showed good shelf life during 6 months, and viability was maintained or slightly decreased by 0·2-0·3-log. CPA-8 formulations after 4- and 6 months storage were effective in controlling brown rot caused by Monilinia spp. on nectarines and peaches resulting in a 90-100% reduction in disease incidence. Stable and effective formulations of biocontrol agent B. subtilis CPA-8 could be obtained by spray-drying. New shelf-stable and effective formulations of a biocontrol agent have been obtained by spray-drying to control brown rot on peach. © 2012 The Authors. Journal of Applied Microbiology © 2012 The Society for Applied Microbiology.

  2. Determination of drying characteristics and quality properties of eggplant in different drying conditions

    Directory of Open Access Journals (Sweden)

    Gözde Bayraktaroglu Urun

    2015-12-01

    Full Text Available Drying is the most traditional process used for preserving eggplant a long time. The aim of this study was to determining drying characteristics and quality properties of eggplant dried by sun drying, hot air convective drying and infrared assisted convective drying. Convective drying and infrared assisted convective were carried out in a convective dryer at three different temperatures(40°, 50°, 60°C and air velocity at 5 m/s.The increasing of temperatures during the drying of eggplant led to a significant reduction of the drying time. However loss of nutrition was observed in eggplant samples dried at higher temperature.The biggest change in colour parameters was observed in samples dried with sun drying.So it was thought that sun drying had a negative effect on quality properties of eggplant samples.

  3. Transformation of Mg-bearing amorphous calcium carbonate to Mg-calcite - In situ monitoring

    Science.gov (United States)

    Purgstaller, Bettina; Mavromatis, Vasileios; Immenhauser, Adrian; Dietzel, Martin

    2016-02-01

    The formation of Mg-bearing calcite via an amorphous precursor is a poorly understood process that is of relevance for biogenic and abiogenic carbonate precipitation. In order to gain an improved insight on the controls of Mg incorporation in calcite formed via an Mg-rich amorphous calcium carbonate (Mg-ACC) precursor, the precipitation of Mg-ACC and its transformation to Mg-calcite was monitored by in situ Raman spectroscopy. The experiments were performed at 25.0 ± 0.03 °C and pH 8.3 ± 0.1 and revealed two distinct pathways of Mg-calcite formation: (i) At initial aqueous Mg/Ca molar ratios ⩽ 1:6, Mg-calcite formation occurs via direct precipitation from solution. (ii) Conversely, at higher initial Mg/Ca molar ratios, Mg-calcite forms via an intermediate Mg-rich ACC phase. In the latter case, the final product is a calcite with up to 20 mol% Mg. This Mg content is significant higher than that of the Mg-rich ACC precursor phase. Thus, a strong net uptake of Mg ions from the solution into the crystalline precipitate throughout and also subsequent to ACC transformation is postulated. Moreover, the temporal evolution of the geochemical composition of the reactive solution and the Mg-ACC has no significant effect on the obtained ;solubility product; of Mg-ACC. The enrichment of Mg in calcite throughout and subsequent to Mg-ACC transformation is likely affected by the high aqueous Mg/Ca ratio and carbonate alkalinity concentrations in the reactive solution. The experimental results have a bearing on the formation mechanism of Mg-rich calcites in marine early diagenetic environments, where high carbonate alkalinity concentrations are the rule rather than the exception, and on the insufficiently investigated inorganic component of biomineralisation pathways in many calcite secreting organisms.

  4. Short communication: Effect of heat stress on markers of autophagy in the mammary gland during the dry period.

    Science.gov (United States)

    Wohlgemuth, S E; Ramirez-Lee, Y; Tao, S; Monteiro, A P A; Ahmed, B M; Dahl, G E

    2016-06-01

    Heat stress (HT) during the dry period compromises mammary gland (MG) growth, thus negatively affecting subsequent milk yield. Cooling during the late dry period, when mammary tissue proliferates, is a common management practice. However, it neglects MG involution during the early dry period, a process that is accomplished by both apoptosis and autophagy. Our objective was to evaluate the effect of HT on MG autophagy during the early dry period. Holstein cows were dried off ~45d before expected calving and randomly assigned to 1 of 2 treatments: HT or cooling (CL). All cows were housed in the same free stall barn during the dry period, but only the stall area for CL cows was equipped with soakers and fans. Rectal temperature and respiration rate were measured daily during the dry period. Mammary gland biopsies were collected from each cow 3d before dry-off and on d 3, 7, 14, and 22±2 after dry-off. Autophagy in the MG was determined by measuring protein expression of 2 autophagic markers, autophagy-related protein 7 and microtubule-associated protein light chain 3 (LC3). The average temperature-humidity index during the dry period was 77.7, which indicated that HT and CL cows were exposed to significant heat stress. However, the cooling system effectively alleviated heat strain in CL cows by decreasing the rectal temperature (39.0 vs. 39.4°C) and respiration rate (47.3 vs. 71.2 breaths per minute) relative to HT cows. Protein expression of autophagy-related protein 7, a marker for early autophagosome formation, did not change within or between groups. In contrast, protein expression of LC3-II, a marker of autophagosomes, and its precursor LC3-I showed a dynamic expression pattern in MG from CL cows during the early dry period. Relative to HT cows, MG from CL cows displayed higher expression of LC3-I and LC3-II on d 7 and lower expression of LC3-II on d 14 and 22 after dry-off. Collectively, our data provide a possible mechanistic explanation for the impairment of

  5. Predictors of weight maintenance

    NARCIS (Netherlands)

    Pasman, W.J.; Saris, W.H.M.; Westerterp-Plantenga, M.S.

    1999-01-01

    Objective: To obtain predictors of weight maintenance after a weight-loss intervention. Research Methods and Procedures: An overall analysis of data from two-long intervention studies [n = 67 women; age: 37.9±1.0 years; body weight (BW): 87.0±1.2 kg; body mass index: 32.1±0.5 kg·m-2; % body fat:

  6. Robustness of weighted networks

    Science.gov (United States)

    Bellingeri, Michele; Cassi, Davide

    2018-01-01

    Complex network response to node loss is a central question in different fields of network science because node failure can cause the fragmentation of the network, thus compromising the system functioning. Previous studies considered binary networks where the intensity (weight) of the links is not accounted for, i.e. a link is either present or absent. However, in real-world networks the weights of connections, and thus their importance for network functioning, can be widely different. Here, we analyzed the response of real-world and model networks to node loss accounting for link intensity and the weighted structure of the network. We used both classic binary node properties and network functioning measure, introduced a weighted rank for node importance (node strength), and used a measure for network functioning that accounts for the weight of the links (weighted efficiency). We find that: (i) the efficiency of the attack strategies changed using binary or weighted network functioning measures, both for real-world or model networks; (ii) in some cases, removing nodes according to weighted rank produced the highest damage when functioning was measured by the weighted efficiency; (iii) adopting weighted measure for the network damage changed the efficacy of the attack strategy with respect the binary analyses. Our results show that if the weighted structure of complex networks is not taken into account, this may produce misleading models to forecast the system response to node failure, i.e. consider binary links may not unveil the real damage induced in the system. Last, once weighted measures are introduced, in order to discover the best attack strategy, it is important to analyze the network response to node loss using nodes rank accounting the intensity of the links to the node.

  7. Molybdenum reduction to molybdenum blue in Serratia sp. Strain DRY5 is catalyzed by a novel molybdenum-reducing enzyme.

    Science.gov (United States)

    Shukor, M Y; Halmi, M I E; Rahman, M F A; Shamaan, N A; Syed, M A

    2014-01-01

    The first purification of the Mo-reducing enzyme from Serratia sp. strain DRY5 that is responsible for molybdenum reduction to molybdenum blue in the bacterium is reported. The monomeric enzyme has an apparent molecular weight of 105 kDalton. The isoelectric point of this enzyme was 7.55. The enzyme has an optimum pH of 6.0 and maximum activity between 25 and 35°C. The Mo-reducing enzyme was extremely sensitive to temperatures above 50°C (between 54 and 70°C). A plot of initial rates against substrate concentrations at 15 mM 12-MP registered a V max for NADH at 12.0 nmole Mo blue/min/mg protein. The apparent K m for NADH was 0.79 mM. At 5 mM NADH, the apparent V max and apparent K m values for 12-MP of 12.05 nmole/min/mg protein and 3.87 mM, respectively, were obtained. The catalytic efficiency (k cat/K m ) of the Mo-reducing enzyme was 5.47 M(-1) s(-1). The purification of this enzyme could probably help to solve the phenomenon of molybdenum reduction to molybdenum blue first reported in 1896 and would be useful for the understanding of the underlying mechanism in molybdenum bioremediation involving bioreduction.

  8. Molybdenum Reduction to Molybdenum Blue in Serratia sp. Strain DRY5 Is Catalyzed by a Novel Molybdenum-Reducing Enzyme

    Directory of Open Access Journals (Sweden)

    M. Y. Shukor

    2014-01-01

    Full Text Available The first purification of the Mo-reducing enzyme from Serratia sp. strain DRY5 that is responsible for molybdenum reduction to molybdenum blue in the bacterium is reported. The monomeric enzyme has an apparent molecular weight of 105 kDalton. The isoelectric point of this enzyme was 7.55. The enzyme has an optimum pH of 6.0 and maximum activity between 25 and 35°C. The Mo-reducing enzyme was extremely sensitive to temperatures above 50°C (between 54 and 70°C. A plot of initial rates against substrate concentrations at 15 mM 12-MP registered a Vmax for NADH at 12.0 nmole Mo blue/min/mg protein. The apparent Km for NADH was 0.79 mM. At 5 mM NADH, the apparent Vmax and apparent Km values for 12-MP of 12.05 nmole/min/mg protein and 3.87 mM, respectively, were obtained. The catalytic efficiency (kcat/Km of the Mo-reducing enzyme was 5.47 M-1 s-1. The purification of this enzyme could probably help to solve the phenomenon of molybdenum reduction to molybdenum blue first reported in 1896 and would be useful for the understanding of the underlying mechanism in molybdenum bioremediation involving bioreduction.

  9. Performance of Clarias gariepinus Fed Dried Brewer's Yeast (Saccharomyces cerevisiae) Slurry in Replacement for Soybean Meal.

    Science.gov (United States)

    Solomon, Shola Gabriel; Ataguba, Gabriel Arome; Itodo, Gabriel Enemona

    2017-01-01

    Following disparity of earlier results, this study tested the performance of African catfish Clarias gariepinus fed dried brewer's yeast slurry meal (DBYM) based diets. Fingerlings of C. gariepinus with pooled mean initial weight of 1.58 ± 0.01 g were stocked in hapas (1 m × 1 m × 1 m) immersed in an earthen pond at a density of 15 fish per cage. Five diets with increasing substitution of soybean meal with 25%, 50%, 75%, and 100% of dried brewer's yeast and a control without dried brewer's yeast (0% substitution) were evaluated for 8 weeks. Palatability of diets reduced with increasing levels of DBYM. Growth and utilization parameters such as weight gain, feed conversion ratio, protein efficiency ratio, and specific growth rate differed significantly ( p meal with DBYM in C. gariepinus feed is between 1% and 14% of dry matter.

  10. Re-examining the 26Mg(α ,α')26Mg reaction: Probing astrophysically important states in 26Mg

    Science.gov (United States)

    Adsley, P.; Brümmer, J. W.; Li, K. C. W.; Marín-Lámbarri, D. J.; Kheswa, N. Y.; Donaldson, L. M.; Neveling, R.; Papka, P.; Pellegri, L.; Pesudo, V.; Pool, L. C.; Smit, F. D.; van Zyl, J. J.

    2017-11-01

    Background: The 22Ne(α ,n )25Mg reaction is one of the neutron sources for the s process in massive stars. The properties of levels in 26Mg above the α -particle threshold control the strengths of the 22Ne(α ,n )25Mg and 22Ne(α ,γ )26Mg reactions. The strengths of these reactions as functions of temperature are one of the major uncertainties in the s process. Purpose: Information on the existence, spin, and parity of levels in 26Mg can assist in constraining the strengths of the 22Ne(α ,γ )26Mg and 22Ne(α ,n )25Mg reactions, and therefore in constraining s -process abundances. Methods: Inelastically scattered α particles from a 26Mg target were momentum-analyzed in the K600 magnetic spectrometer at iThemba LABS, South Africa. The differential cross sections of states were deduced from the focal-plane trajectory of the scattered α particles. Based on the differential cross sections, spin and parity assignments to states are made. Results: A newly assigned 0+ state was observed in addition to a number of other states, some of which can be associated with states observed in other experiments. Some of the deduced Jπ values of the states observed in the present study show discrepancies with those assigned in a similar experiment performed at RCNP Osaka. The reassignments and additions of the various states can strongly affect the reaction rate at low temperatures. Conclusion: The number, location, and assignment of levels in 26Mg that may contribute to the 22Ne+α reactions are not clear. Future experimental investigations of 26Mg must have an extremely good energy resolution to separate the contributions from different levels. Coincidence experiments of 26Mg provide a possible route for future investigations.

  11. The determination of optimum condition in water hyacinth drying process by mixed adsorption drying method and modified fly ash as an adsorbent

    Science.gov (United States)

    Saputra, Asep Handaya; Putri, Rizky Anggreini

    2017-05-01

    Water hyacinth is an aquatic weed that has a very fast growth which makes it becomes a problem to the ecosystem. On the other hand, water hyacinth has a high fiber content (up to 20% by weight) which makes it potential to become raw material for composites and textile industries. As an aquatic plant, water hyacinth has a high initial moisture content that reaches more than 90%. Meanwhile the moisture content of fiber as a raw material for composite and textile industry should not be more than 10% to maintain the good quality of the products. Mixed adsorption drying method is one of the innovative method that can replace conventional drying process. Fluidization method which has been commonly used in agricultural and pharmaceutical products drying, can be enhanced by combining it with the adsorption method as performed in this study. In mixed fluidization-adsorption drying method, fly ash as adsorbent and water hyacinth fiber were put together into the fluidization column where the drying air evaporate the moisture content in water hyacinth fiber. In addition, the adsorbent adsorb the moisture content in the drying air to make the moisture content of the drying air remain low. The drying process is performed in various temperature and composition of water hyacinth and adsorbent in order to obtain the optimum drying condition. In addition, the effect of fly ash pellet and fly ash powder to the drying process was also performed. The result shows that the higher temperature and the more amount of adsorbent results in the faster drying rate. Fly ash pellet shows a better adsorption since it has a smaller pore diameter and wider surface area. The optimum temperature obtained from this study is 60°C and the optimum ratio of water hyacinth and fly ash is 50:50.

  12. Specific heat of MgB_2 after irradiation

    OpenAIRE

    Wang, Yuxing; Bouquet, Frederic; Sheikin, Ilya; Toulemonde, Pierre; Revaz, Bernard; Eisterer, Michael; Weber, Harald W.; Hinderer, Joerg; Junod, Alain

    2002-01-01

    We studied the effect of disorder on the superconducting properties of polycrystalline MgB_2 by specific-heat measurements. In the pristine state, these measurements give a bulk confirmation of the presence of two superconducting gaps with 2 Delta 0 / k_B T_c = 1.3 and 3.9 with nearly equal weights. The scattering introduced by irradiation suppresses T_c and tends to average the two gaps although less than predicted by theory. We also found that by a suitable irradiation process by fast neutr...

  13. Solar Drying in Hot and Dry Climate of Jaipur

    OpenAIRE

    Parikh, Darshit; Agrawal, G. D.

    2016-01-01

    Objective of the present study was to design, develop and to carry out detail experimentation and then analyze solar cabinet dryer. For these various types of solar dryer, their principles and design methods, modeling, drying temperature, efficiency, utilization of dryer and payback period were reviewed. In the present study, solar cabinet dryer is constructed at Mechanical Engineering Department, M.N.I.T, Jaipur, latitude (26.01° N). The measurement of solar intensity, temperatures, relative...

  14. Oxidation characteristics of MgF2 in air at high temperature

    Science.gov (United States)

    Chen, H. K.; Jie, Y. Y.; Chang, L.

    2017-02-01

    High temperature oxidation properties of MgF2 in air were studied. The changes of phase composition, macro surface morphology, weight and elemental composition of MgF2 samples with temperature were investigated by using XRD, EDS and gravimetric analyses. The results show that the oxidation reaction of MgF2 converted to MgO occurred at high temperature, and the reaction was accelerated by the increase of temperature and the presence of impurities. This result clarifies the understanding of the high temperature oxidation behavior of MgF2 in air, and provides a theoretical basis for the reasonable application of MgF2 in optical coating materials, electronic ceramic materials and magnesium melt protection.

  15. Embriões liofilizados e flocos de Artemia no cultivo pós-larval de Litopenaeus vannamei (Boone, 1931 = Use of freeze-dried embryos and Artemia flakes in the post-larval culture of Litopenaeus vannamei (Boone, 1931

    Directory of Open Access Journals (Sweden)

    Pedro Hercílio de Oliveira Cavalcante

    2008-01-01

    Full Text Available O objetivo do estudo foi avaliar o crescimento e sobrevivência de 1pós-larvas de Litopenaeus vannamei que receberam embriões liofilizados (EMB e flocos (FLO de Artemia como suplementos alimentares a uma dieta microparticulada (DMP. Nos tratamentos T1,T2 e T3, os camarões receberam DMP e após 2h, acréscimos de FLO (T1; de EMB (T2; e da mesma DMP, anteriormente, ofertada (T3. No T4, as pós-larvas foram alimentadas com DMP, mas sem suplementações posteriores. Não houve diferença significativa (p > 0,05 na sobrevivência dos camarões após o período experimental de 21 dias. Por outro lado, o ganho de peso absoluto (mg peso seco das pós-larvas, cuja dieta foi suplementada com BEM, foi significativamente superior (p The objective of the study was to evaluate the growth and survival of Litopenaeus vannamei post-larvae fed with freeze-driedembryos and Artemia flakes as feeding supplements to a microparticulate diet (DMP. In treatments T1, T2 and T3, the shrimp were fed with DMP and after 2 hours, received supplements of FLO (T1; EMB (T2; and the same DMP previously offered (T3. In T4,post-larvae were fed with DMP but without additional supplementation. There was no significant difference (p > 0.05 in shrimp survival after the experimental period of 21 days. On the other hand, the absolute weight gain (mg of dry weight of post-larvae whose dietwas supplemented with EMB (T2 was significantly higher (p < 0.05 than growth found in the other experimental groups (T1, T3 and T4. Shrimp fed with DMP and EMB obtained a significantly higher absolute weight gain (6.7 mg than those found in treatments that used DMP and FLO (5.4 mg or DMP alone (5.8 mg in T3 and 5.7 mg in T4. Theseresults underline the nutritional value of freeze-dried Artemia embryos and recommend their inclusion in the post-larval diet of Litopenaeus vannamei.

  16. Research on MgLi and a specifically German consequence. MgLi-Forschung und ihre spezifisch deutsche Konsequenz

    Energy Technology Data Exchange (ETDEWEB)

    Hehmann, F [Office National d' Etudes et de Recherches Aerospatiales (ONERA), 92 - Chatillon (France)

    1994-05-01

    When light weight structural applications are of prime concern, magnesium cannot be ignored. When magnesium is of prime concern, of course, the research cannot be ignored, either. Since there is not much to be ignored (or not), however, it is the research on MgLi that takes the lead in the German press. ''Rock-solid as Kruppstahl'' was it meant to be, though MgLi-alloys soften quite appreciable already at ambient temperature. A hydrogen treatment of the MgLi melt was the phenomenon that was naturally astounded. In the meantime, however, it became very tranquilly around the contest for the selection of the species from the ''MgLi-Born''. Has the hot air already escaped Warm wind is not bad in each case. Daily discipline, however, has scaled ever since with the natural beauty of the more concrete results by working. What follows is an article that looks upon this particular German variant at the ''histoire parallele'' in the field of metallic innovations as well as upon the sound base of such deliberately outbalanced renaissances. (orig.)

  17. Theoretical and experimental study of the intrinsic physical properties of the Mg-MgH{sub 2} system

    Energy Technology Data Exchange (ETDEWEB)

    Puszkiel, Julian A.; Gervasoni, Juana L. [Centro Atomico Bariloche (CAB) - Instituto Balseiro (IB) - Comision Nacional de Energia Atomica (CNEA), Av. Bustillo km 9.5, R8402 AGP S.C. de Bariloche (Argentina)

    2010-06-15

    Due to the fundamental problems of energy source limitations and environmental pollution, hydrogen has become an attractive clean energy source for the future. Despite the fact that the incentive to switch to a hydrogen economy has increased, there are many problems which must be solved. One of the main unsolved issues is hydrogen storage. Among the potential materials to store hydrogen in a safe way, Mg has drawn interest owing to its high hydrogen capacity (7.6 wt%), light weight and low cost. In order to improve the hydrogen capacity of potential storage materials such as Mg, it is important to understand the site preferences of hydrogen atoms in the metal. Such behavior depends mainly on the screening charge density ({delta}n(r)) of the system proton-metallic host, from which all the physical macroscopic properties (viz. V{sub H}, {delta}H{sub S}, B, etc.) and IDOS are determined. In the present work we study the interaction between a proton and Mg as host metal via ab initio calculations, using the Jellium model, based on the density-functional theory (DFT). The macroscopic properties are determined and compared with experimental results and values found in the bibliography. Furthermore, in order to obtain information about the electronic distribution of hydrogen and the nature of the Mg-H bonding, the IDOS is described. (author)

  18. Presence or absence of ocular surface inflammation directs clinical and therapeutic management of dry eye

    Directory of Open Access Journals (Sweden)

    Sambursky R

    2016-11-01

    Full Text Available Robert Sambursky Coastal Eye Institute, Cornea and Comprehensive Ophthalmology, Bradenton, FL, USA Background: The presence of clinically significant inflammation has been confirmed in the tears of 40%–65% of patients with symptoms of dry eye. Ocular surface inflammation may lead to tear film instability, epithelial cell irregularities, and permeability, resulting in chronic symptomatic pain and fluctuating vision as well as negative surgical outcomes.Patients and methods: A retrospective single center medical chart review of 100 patients was conducted. All patients were tested with the InflammaDry test to determine if patients exhibited elevated levels of matrix metalloproteinase 9 (MMP-9. InflammaDry-positive patients were started on a combination of cyclosporine 0.05% twice daily, 2,000–4,000 mg oral omega-3 fatty acids, and frequent artificial tear replacement. InflammaDry-negative patients were started on 2,000–4,000 mg of oral omega-3 fatty acids and frequent artificial tear replacement. Each patient was retested at ~90 days. A symptom questionnaire was performed at the initial visit and at 90 days.Results: 60% of the patients with dry eye symptoms tested positive for elevated MMP-9 at the initial visit. 78% of all patients returned for follow-up at ~90 days including 80% (48/60 of the previously InflammaDry-positive patients and 75% (30/40 of the previously InflammaDry-negative patients. A follow-up symptom questionnaire reported at least 75% symptomatic improvement in 65% (31/48 of the originally InflammaDry-positive patients and in 70% (21/30 of the initially InflammaDry-negative patients. Symptomatic improvement of at least 50% was reported in 85% (41/48 of previously InflammaDry-positive patients and 86% (26/30 of previously InflammaDry-negative patients. Following treatment, 54% (26/48 of previously InflammaDry-positive patients converted to a negative InflammaDry result.Conclusion: Identifying which symptomatic dry eye

  19. Reduced weight decontamination formulation for neutralization of chemical and biological warfare agents

    Science.gov (United States)

    Tucker, Mark D.

    2014-06-03

    A reduced weight DF-200 decontamination formulation that is stable under high temperature storage conditions. The formulation can be pre-packed as an all-dry (i.e., no water) or nearly-dry (i.e., minimal water) three-part kit, with make-up water (the fourth part) being added later in the field at the point of use.

  20. X-ray microanalysis of freeze-dried and frozen-hydrated cryosections

    International Nuclear Information System (INIS)

    Zierold, K.

    1988-01-01

    The elemental composition and the ultrastructure of biological cells were studied by scanning transmission electron microscopy (STEM) combined with energy dispersive X-ray microanalysis. The preparation technique involves cryofixation, cryoultramicrotomy, cryotransfer, and freeze-drying of samples. Freeze-dried cryosections 100-nm thick appeared to be appropriate for measuring the distribution of diffusible elements and water in different compartments of the cells. The lateral analytical resolution was less than 50 nm, depending on ice crystal damage and section thickness. The detection limit was in the range of 10 mmol/kg dry weight for all elements with an atomic number higher than 12; for sodium and magnesium the detection limits were about 30 and 20 mmol/kg dry weight, respectively. The darkfield intensity in STEM is linearly related to the mass thickness. Thus, it becomes possible to measure the water content in intracellular compartments by using the darkfield signal of the dry mass remaining after freeze-drying. By combining the X-ray microanalytical data expressed as dry weight concentrations with the measurements of the water content, physiologically more meaningful wet weight concentrations of elements were determined. In comparison to freeze-dried cryosections frozen-hydrated sections showed poor contrast and were very sensitive against radiation damage, resulting in mass loss. The high electron exposure required for recording X-ray spectra made reproducible microanalysis of ultrathin (about 100-nm thick) frozen-hydrated sections impossible. The mass loss could be reduced by carbon coating; however, the improvement achieved thus far is still insufficient for applications in X-ray microanalysis. Therefore, at present only bulk specimens or at least 1-micron thick sections can be used for X-ray microanalysis of frozen-hydrated biological samples

  1. Use of dry sludge from waste water treatment plants as an additive in prefabricated concrete brick

    OpenAIRE

    Yagüe, A.; Valls, S.; Vázquez, E.; Kuchinow, V.

    2002-01-01

    Dry sludge from the Sabadell Water Treatment Plant was used to prepare prefabricated concrete bricks. After characterising the sludge and the manufacturing process used to make the bricks, we define the conditions of addition of the sludges in the manufacture. Reference samples not containing sludge and samples containing 2 % of dry sludge by cement weight were prepared. The variation in density, porosity, absorption coefficient and compressive strength of the bricks with the presence of...

  2. Drying kinetics and characteristics of dried gambir leaves using solar heating and silica gel dessicant

    Science.gov (United States)

    Hasibuan, R.; Hidayati, J.; Sundari, R.; Wicaksono, A. S.

    2018-02-01

    A drying combination of solar heating and silica gel dessicant has been applied to dry gambir leaves. The solar energy is captured by a collector to heat the air and the hot air is used to dry gambir leaves in a drying chamber. An exhaust fan in drying chamber assists to draw water molecules from gambir leaves accelerated by silica gel dessicant. This study has investigated the drying kinetics and drying characteristics of gambir leaves drying. In drying operation the air velocity is tuned by a PWM (pulse width modulation) controller to adjust minimum and maximum level, which is based on the rotation speed of the exhaust fan. The results show that the air velocity influenced the drying kinetics and drying characteristics of gambir leaves using solar-dessicant drying at 40 cm distance between exhaust fan and silica gel dessicant.

  3. Clay as a matrix former for spray drying of drug nanosuspensions.

    Science.gov (United States)

    Dong, Yuancai; Ng, Wai Kiong; Hu, Jun; Shen, Shoucang; Tan, Reginald B H

    2014-04-25

    Utilization of sugars (e.g. lactose, sucrose) as matrix formers for spray drying of drug nanosuspensions is associated with two drawbacks: (1) sugars are incapable of preventing agglomeration of drug nanoparticles (NPs) in the suspension state; and (2) the spray-dried sugars are usually amorphous and hygroscopic. This work aimed to apply a clay, montmorillonite (MMT) as an alternative matrix former for spray drying of drug nanosuspensions with fenofibrate (feno) as a model compound. Drug nanosuspensions were synthesized by liquid antisolvent precipitation with different amount of MMT followed by spray drying. It is found that MMT is able to reduce the agglomeration of drug nanoparticles in the suspension state, as observed from the gradual alleviation of the clogging with the increased clay during the spray drying. The spray-dried feno NPs/MMT powders exhibited a much lower moisture sorption than spray-dried feno NPs/lactose powders as evidenced by the dynamic vapor sorption (DVS) analysis. The dissolution within 5 min for the spray-dried feno NPs/MMT powders at drug:MMT weight ratio of 1:3 was 81.4 ± 1.8% and the total dissolution within 60 min was 93.4 ± 0.9%. Our results demonstrate that MMT is a useful matrix former for preservation of the high dissolution rate of nanosized drug particles after drying. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Changes in polyphenol profile of dried apricots containing SO2 at various concentrations during storage.

    Science.gov (United States)

    Altındağ, Melek; Türkyılmaz, Meltem; Özkan, Mehmet

    2018-05-01

    Changes in polyphenols have important effects on the quality (especially color) and health benefits of dried apricots. SO 2 concentration, storage and the activities of polyphenol oxidase (PPO) and phenylalanine ammonia lyase (PAL) were factors which had significant effects on polyphenols. Polyphenol profile and activities of PPO and PAL in sulfured dried apricots (SDAs, 0, 451, 832, 2112 and 3241 mg SO 2 kg -1 ) were monitored during storage at 4, 20 and 30 °C for 379 days for the first time. Even the lowest SO 2 concentration (451 mg kg -1 ) was sufficient to inactivate PPO during the entire storage period. However, while SO 2 led to the increase in PAL activity of the samples (r = 0.767) before storage, PAL activities of SDAs decreased during storage. After 90 days of storage, PAL activity was determined in only non-sulfured dried apricots (NSDAs) and dried apricots containing 451 mg SO 2 kg -1 . Although the major polyphenol in NSDAs was epicatechin (611.4 mg kg -1 ), that in SDAs was chlorogenic acid (455-1508 mg kg -1 ), followed by epicatechin (0-426.8 mg kg -1 ), rutin (148.9-477.3 mg kg -1 ), ferulic acid (23.3-55.3 mg kg -1 ) and gallic acid (2.4-43.6 mg kg -1 ). After storage at 30 °C for 379 days, the major polyphenol in SDAs was gallic acid (706-2324 mg kg -1 ). However, the major polyphenol in NSDAs did not change after storage. The highest total polyphenol content was detected in SDAs containing 2112 mg SO 2 kg -1 and stored at 30 °C. To produce dried apricots having high polyphenol content, ∼2000 mg SO 2 kg -1 should be used. Low storage temperature (<30 °C) was not necessary for the protection of polyphenols. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  5. Production of cocrystals in an excipient matrix by spray drying.

    Science.gov (United States)

    Walsh, David; Serrano, Dolores R; Worku, Zelalem Ayenew; Norris, Brid A; Healy, Anne Marie

    2018-01-30

    Spray drying is a well-established scale-up technique for the production of cocrystals. However, to the best of our knowledge, the effect of introducing a third component into the feed solution during the spray drying process has never been investigated. Cocrystal formation in the presence of a third component by a one-step spray drying process has the potential to reduce the number of unit operations which are required to produce a final pharmaceutical product (e.g. by eliminating blending with excipient). Sulfadimidine (SDM), a poorly water soluble active pharmaceutical ingredient (API), and 4-aminosalicylic acid (4ASA), a hydrophilic molecule, were used as model drug and coformer respectively to form cocrystals by spray drying in the presence of a third component (excipient). The solubility of the cocrystal in the excipient was measured using a thermal analysis approach. Trends in measured solubility were in agreement with those determined by calculated Hansen Solubility Parameter (HSP) values. The ratio of cocrystal components to excipient was altered and cocrystal formation at different weight ratios was assessed. Cocrystal integrity was preserved when the cocrystal components were immiscible with the excipient, based on the difference in Hansen Solubility Parameters (HSP). For immiscible systems (difference in HSP > 9.6 MPa 0.5 ), cocrystal formation occurred even when the proportion of excipient was high (90% w/w). When the excipient was partly miscible with the cocrystal components, cocrystal formation was observed post spray drying, but crystalline API and coformer were also recovered in the processed powder. An amorphous dispersion was formed when the excipient was miscible with the cocrystal components even when the proportion of excipient used as low (10% w/w excipient). For selected spray dried cocrystal-excipient systems an improvement in tableting characteristics was observed, relative to equivalent physical mixtures. Copyright © 2017 Elsevier

  6. Preparation and characterization of fast dissolving flurbiprofen and esomeprazole solid dispersion using spray drying technique.

    Science.gov (United States)

    Pradhan, Roshan; Tran, Tuan Hiep; Kim, Sung Yub; Woo, Kyu Bong; Choi, Yong Joo; Choi, Han-Gon; Yong, Chul Soon; Kim, Jong Oh

    2016-04-11

    We aimed to develop an immediate-release flurbiprofen (FLU) and esomeprazole (ESO) combination formulation with enhanced gastric aqueous solubility and dissolution rate. Aqueous solubility can be enhanced by formulating solid dispersions (SDs) with a polyvinylpyrrolidone (PVP)-K30 hydrophilic carrier, using spray-drying technique. Aqueous and gastric pH dissolution can be achieved by macro-environmental pH modulation using sodium bicarbonate (NaHCO3) and magnesium hydroxide (Mg(OH)2) as the alkaline buffer. FLU/ESO-loaded SDs (FLU/ESO-SDs) significantly improved aqueous solubility of both drugs, compared to each drug powder. Dissolution studies in gastric pH and water were compared with the microenvironmental pH modulated formulations. The optimized FLU/ESO-SD powder formulation consisted of FLU/ESO/PVP-K30/sodium carbonate (Na2CO3) in a weight ratio 1:0.22:1.5:0.3, filled in the inner capsule. The outer capsule consisted of NaHCO3 and Mg(OH)2, which created the macro-environmental pH modulation. Increased aqueous and gastric pH dissolution of FLU and ESO from the SD was attributed to the alkaline buffer effects and most importantly, to drug transformation from crystalline to amorphous SD powder, clearly revealed by scanning electron microscopy, differential scanning calorimetry, and powder X-ray diffraction studies. Thus, the combined FLU and ESO SD powder can be effectively delivered as an immediate-release formulation using the macro-environmental pH modulation concept. Copyright © 2016. Published by Elsevier B.V.

  7. Effect of Fishmeal Supplementation on Body Weight Gain of White ...

    African Journals Online (AJOL)

    Two 8-week feeding trials were carried out to investigate the effect of supplementing an inadequate commercial diet available in Eritrea. with fishmeal produced locally by sun-drying and grinding on the body weight gain of White Leghorn chicks. The commercial diet consisted 'of a mixture of sorghum, wheat middlings, ...

  8. Weighted Bergman Kernels for Logarithmic Weights

    Czech Academy of Sciences Publication Activity Database

    Engliš, Miroslav

    2010-01-01

    Roč. 6, č. 3 (2010), s. 781-813 ISSN 1558-8599 R&D Projects: GA AV ČR IAA100190802 Keywords : Bergman kernel * Toeplitz operator * logarithmic weight * pseudodifferential operator Subject RIV: BA - General Mathematics Impact factor: 0.462, year: 2010 http://www.intlpress.com/site/pub/pages/journals/items/pamq/content/vols/0006/0003/a008/

  9. Body Weight - Multiple Languages

    Science.gov (United States)

    ... Supplements Videos & Tools You Are Here: Home → Multiple Languages → All Health Topics → Body Weight URL of this page: https://medlineplus.gov/ ... V W XYZ List of All Topics All Body Weight - Multiple Languages To use the sharing features on this page, ...

  10. Concurrent weighted logic

    DEFF Research Database (Denmark)

    Xue, Bingtian; Larsen, Kim Guldstrand; Mardare, Radu Iulian

    2015-01-01

    We introduce Concurrent Weighted Logic (CWL), a multimodal logic for concurrent labeled weighted transition systems (LWSs). The synchronization of LWSs is described using dedicated functions that, in various concurrency paradigms, allow us to encode the compositionality of LWSs. To reflect these......-completeness results for this logic. To complete these proofs we involve advanced topological techniques from Model Theory....

  11. Unexplained Weight Loss

    Science.gov (United States)

    ... weight is affected by your calorie intake, activity level, overall health, age, nutrient absorption, and economic and social factors. If you're losing weight without trying and you're concerned about it, consult your doctor — as a rule of thumb, losing more than 5 ...

  12. Thyroid and Weight

    Science.gov (United States)

    ... Hypothyroidism in Children and Adolescents Pediatric Differentiated Thyroid Cancer Thyroid Nodules in Children and Adolescents Thyroid and Weight Resources Thyroid and Weight Brochure PDF En Español La Tiroides y el Peso El folleto de La Tiroides y el ...

  13. Adolescent Weight Status

    DEFF Research Database (Denmark)

    Hjort Kjelldgaard, Heidi; Holstein, Bjørn Evald; Due, Pernille

    2017-01-01

    day) communication with friends through cellphones, SMS messages, or Internet (1.66, 1.03-2.67). In the full population, overweight/obese weight status was associated with not perceiving best friend as a confidant (1.59, 1.11-2.28). No associations were found between weight status and number of close...

  14. Isotopes and atomic weights

    International Nuclear Information System (INIS)

    Zhang Qinglian

    1990-01-01

    A review of the chemical and mass spectrometric methods of determining the atomic weights of elements is presented. A, special discussion is devoted to the calibration of the mass spectrometer with highly enriched isotopes. It is illustrated by the recent work on europium. How to choose the candidate element for new atomic weight determination forms the last section of the article

  15. Cracking in Drying Colloidal Films

    Science.gov (United States)

    Singh, Karnail B.; Tirumkudulu, Mahesh S.

    2007-05-01

    It has long been known that thick films of colloidal dispersions such as wet clays, paints, and coatings crack under drying. Although capillary stresses generated during drying have been recently identified as the cause for cracking, the existence of a maximum crack-free film thickness that depends on particle size, rigidity, and packing has not been understood. Here, we identify two distinct regimes for crack-free films based on the magnitude of compressive strain at the maximum attainable capillary pressure and show remarkable agreement of measurements with our theory. We anticipate our results to not only form the basis for design of coating formulations for the paints, coatings, and ceramics industry but also assist in the production of crack-free photonic band gap crystals.

  16. Dry storage of Magnox fuel

    International Nuclear Information System (INIS)

    1986-09-01

    This work, commissioned by the CEGB, studies the feasibility of a combination of short-term pond storage and long-term dry storage of Magnox spent fuel as a cheaper alternative to reprocessing. Storage would be either at the reactor site or a central site. Two designs are considered, based on existing design work done by GEC-ESL and NNC; the capsule design developed by NNC and with storage in passive vaults for up to 100 yrs and the GEC-ESL tube design developed at Wylfa for the interim storage of LWR. For the long-term storage of Magnox spent fuel the GEC-ESL tubed vault all-dry storage method is recommended and specifications for this method are given. (U.K.)

  17. [Study on the weight-reducing effect of Acer truncatum leave extract in alimentary obesity rat].

    Science.gov (United States)

    Gao, Lifang; Cao, Lige; Tian, Mi; Chen, Zhenliang

    2012-07-01

    To investigate the weight-reducing effect of Acer truncatum leave extract on alimentary obesity rats and its effect on fatty acid synthase (FAS). SPF-grade adult male Wistar rats were fed with high-fat diet and Acer truncatum leave extract (10, 30 and 100 mg/kg BW) was given by gavage once a day for 31 days. Body weight (BW), adipose weight and food consumption were recorded, and the activity of hepatic fatty acid synthase (FAS) was measured. Compared with the model-control group, body weight, adipose weight and the ratio of adipose weight to body weight were obviously lower in 30 mg/kg BW and 100 mg/kg BW groups (P Acer truncatum leave extract on reducing body weight.

  18. Evaluation of a microwave method for dry matter determination in faecal samples from weaned pigs with or without clinical diarrhoea.

    Science.gov (United States)

    Pedersen, Ken Steen; Stege, Helle; Nielsen, Jens Peter

    2011-07-01

    Microwave drying as a procedure for determination of faecal dry matter in weaned pigs was evaluated and clinical relevant cut-off values between faecal consistency scores were determined. Repeatability and reproducibility were evaluated. Overall coefficient of variation was 0.03. The 95% confidence limits for any future faecal subsample examined by any operator in any replica were ± 0.85% faecal dry matter. Robustness in relation to weight of wet faeces was evaluated. The weight categories were 0.5, 1.0, 1.5, 2.0 and 3.0 g. Samples of 0.5 g gave significantly different mean faecal dry matter content compared to weighing of 1.0-3.0 g. Agreement with freeze-drying was evaluated. Lin's concordance correlation coefficient was 0.94. On average the faecal dry matter values was 1.7% (SD=1.99%) higher in freeze dried compared to micro waved samples. Non-parametric ROC analyses were used to determine optimal faecal dry matter cut-off values for clinical faecal consistency scores. The 4 consistency scores were score 1=firm and shaped, score 2=soft and shaped, score 3=loose and score 4=watery. The cut-off values were score 1: faecal dry matter content >19.5%, score 2: faecal dry matter content ≤ 19.5% and >18.0%, score 3: faecal dry matter content ≤ 18.0% and >11.3%, score 4: faecal dry matter content ≤ 11.3%. In conclusion, the microwave procedure has an acceptable repeatability/reproducibility and good agreement with freeze drying can be expected. A minimum of 1.0 g of wet faeces must be used for analyses. Faecal dry matter cut-off values between 4 different clinical consistency scores were determined. © 2011 Elsevier B.V. All rights reserved.

  19. Relationship between moisture content and electrical impedance of carrot slices during drying

    Science.gov (United States)

    Kertész, Ákos; Hlaváčová, Zuzana; Vozáry, Eszter; Staroňová, Lenka

    2015-01-01

    Electrical properties of food materials can give information about the inner structure and physiological state of biological tissues. Generally, the process of drying of fruits and vegetables is followed by weight loss. The aim of this study was to measure the impedance spectra of carrot slices during drying and to correlate impedance parameters to moisture content in different drying periods. Cylindrical slices were cut out from the carrot root along the axis. The slices were dried in a Venticell 111 air oven at 50°C. The weight of the slices was measured with a Denver SI-603 electronic analytical and precision balance. The weighing of the samples was performed every 30 min at the beginning of drying and every 60 min after the process. The moisture content of the samples was calculated on wet basis. The magnitude and phase angle of electrical impedance of the slices were measured with HP 4284A and 4285A precision LCR meters in the frequency range from 30 Hz to 1 MHz and from 75 kHz to 30 MHz, respectively, at voltage 1 V. The impedance measurement was performed after weighting. The change in the magnitude of impedance during drying showed a good correlation with the change in the moisture content.

  20. Reciprocity of weighted networks.

    Science.gov (United States)

    Squartini, Tiziano; Picciolo, Francesco; Ruzzenenti, Franco; Garlaschelli, Diego

    2013-01-01

    In directed networks, reciprocal links have dramatic effects on dynamical processes, network growth, and higher-order structures such as motifs and communities. While the reciprocity of binary networks has been extensively studied, that of weighted networks is still poorly understood, implying an ever-increasing gap between the availability of weighted network data and our understanding of their dyadic properties. Here we introduce a general approach to the reciprocity of weighted networks, and define quantities and null models that consistently capture empirical reciprocity patterns at different structural levels. We show that, counter-intuitively, previous reciprocity measures based on the similarity of mutual weights are uninformative. By contrast, our measures allow to consistently classify different weighted networks according to their reciprocity, track the evolution of a network's reciprocity over time, identify patterns at the level of dyads and vertices, and distinguish the effects of flux (im)balances or other (a)symmetries from a true tendency towards (anti-)reciprocation.

  1. Weight discrimination and bullying.

    Science.gov (United States)

    Puhl, Rebecca M; King, Kelly M

    2013-04-01

    Despite significant attention to the medical impacts of obesity, often ignored are the negative outcomes that obese children and adults experience as a result of stigma, bias, and discrimination. Obese individuals are frequently stigmatized because of their weight in many domains of daily life. Research spanning several decades has documented consistent weight bias and stigmatization in employment, health care, schools, the media, and interpersonal relationships. For overweight and obese youth, weight stigmatization translates into pervasive victimization, teasing, and bullying. Multiple adverse outcomes are associated with exposure to weight stigmatization, including depression, anxiety, low self-esteem, body dissatisfaction, suicidal ideation, poor academic performance, lower physical activity, maladaptive eating behaviors, and avoidance of health care. This review summarizes the nature and extent of weight stigmatization against overweight and obese individuals, as well as the resulting consequences that these experiences create for social, psychological, and physical health for children and adults who are targeted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Antioxidant Potential of the Giant Mushroom, Macrocybe gigantea (Agaricomycetes), from India in Different Drying Methods.

    Science.gov (United States)

    Gaur, Tanvi; Rao, P B

    2016-01-01

    Free radicals are responsible for several diseases like cancer, atherosclerosis, gastric ulcers, and several others. Studies have shown that mushrooms possess antioxidant activity and Macrocybe gigantea was recently added to the list of mushrooms under cultivation in India. The methanolic extracts were prepared from lyophilized and oven-dried samples of MA1 and MA2 strains of M. gigantea and their antioxidant properties were studied. MA2 showed comparatively higher total antioxidant activity (111.88 µg/mg) than MA1 (97.00 µg/mg). The scavenging activity on 2,2'-diphenyl picryl hydrazyl free radical (74.41%), ferrous chelating (83.74%), reducing power (0.371), and superoxide anion radical (72.05%) was significantly higher in freeze-dried MA2 than MA1 at 200 µg/mL. Correspondingly, the EC50 values were lower in freeze-dried states (96.03 µg/mL, 95.00 µg/mL, and 68.12 µg/mL in MA2 and 105.12 µg/mL, 109.8 µg/mL, and 74.60 µg/mL in MA1) than in oven-dried states (97.97 µg/mL, 120.2 µg/mL, and 125.33 µg/mL in MA2 and 108.3 µg/mL, 131.2 µg/mL, and 147.5 µg/mL in MA1, respectively). In addition, total phenolic, total flavonoid, and ortho-dihydroxy phenol content was examined and their values were comparatively higher in freeze-dried MA2 (18.00 mg/g of gallic acid equivalents, 1.67 mg/g of quercetin equivalents, and 1.10 mg/g of catechol equivalents, respectively) than in MA1 and oven-dried states in both strains. Further, MA2 showed lower EC50 values in freeze-dried samples than MA1 and oven-dried states in both strains. These results suggested that MA2 contains higher antioxidant potential than MA1 and freeze-drying by lyophilization retains higher antioxidants than heat drying by a hot air oven in both the strains; thus, they can be a good source of nutraceuticals.

  3. Equipment selection for atmospheric drying

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, P D; Bhattacharyya, S [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    Heavy water management is a major factor in deciding the economics of the PHWRs. Hence it is necessary to have an efficient recovery system, for the heavy water vapour escaping from various process systems and maintain a dry atmosphere in the recovery areas. While the basic objective of the atmospheric drying system is to maximize recovery and to minimize stack losses, it is equally important to optimally design the system with due consideration to operational and maintenance aspects. At present, heavy water vapour recovery in the existing Nuclear Power Plants (NPPs) is carried out by dryers of dual fixed bed design. While moving bed design could have some advantages, this has not been adopted so far because of the cumbersome mechanical design involved and special requirements for nuclear application. Developmental work done in this direction has resulted in compact alternative designs. In one of the designs, the change over from adsorption to regeneration is achieved by rotating the bed slowly. This concept is further refined in another alternative using a dessicant wheel. This paper contains brief equipment description of different designs; enumerates the design requirements of an atmospheric drying system for reactor building; describes steps for designing fixed bed type D{sub 2}O vapour recovery system, and highlights advances in dryer technology. (author). 2 refs., 4 figs., 1 ill.

  4. Magnesium absorption in human subjects from leafy vegetables, intrinsically labeled with stable 26Mg

    International Nuclear Information System (INIS)

    Schwartz, R.; Spencer, H.; Welsh, J.J.

    1984-01-01

    Collards, turnip greens, leaf lettuce, and spinach, grown in nutrient solution so that their Mg content was 80 to 90% 26 Mg, were tested in ambulant male volunteers stabilized on a constant metabolic diet. The freeze-dried vegetables were incorporated in bran muffins in which the vegetables replaced part of the bran. Bran muffins without vegetables were consumed for breakfast each day. They were also used as a standard test meal to which the vegetable muffins were compared. All subjects participated in three consecutive isotope absorption tests: one of the standard test meal and two of the vegetables. The standard test was carried out after at least 30 days on the controlled diet. Subsequent tests of vegetables followed at 4-wk intervals. Each test meal contained 30 microCi 28 MgCl2 and 50 mg stable 26 Mg, the latter either as the intrinsic label of a test vegetable or as 26 MgCl 2 in solution taken with the standard bran muffins. Net absorption of both isotopes was measured to establish exchangeability and to determine relative Mg absorption from the vegetables. Exchangeability was 90% or higher from all meals tested. Relative Mg absorption was highest from collards and least from the standard test meal. Net absorption values ranged from 40 to 60%

  5. Pseudobrookite-type MgTi2O5 water purification filter with controlled particle morphology

    Directory of Open Access Journals (Sweden)

    Yuta Nakagoshi

    2015-09-01

    Full Text Available Pseudobrookite-type oxide-based ceramics, such as Al2TiO5 and MgTi2O5, have recently been studied as porous ceramic membranes. Here, the effect of LiF doping on the morphology of MgTi2O5 particles is presented in detail. Water purification filters were produced using porous MgTi2O5, with different particle morphologies. MgCO3 (basic and TiO2 powders with various LiF contents were wet-ball milled, dried, and then, calcined in air at 1100 °C to obtain the MgTi2O5 powders. The powder compacts were sintered at 1000–1200 °C to produce the MgTi2O5 disk filters. The 0.5 wt.% LiF-doped MgTi2O5 disk filter, with elongated grains, showed well-balanced performance removing boehmite particles with diameter of 0.7 μm. Non-doped MgTi2O5 disk filter with equiaxed grains was suitable for precise filtration.

  6. The effect of the MgO buffer layer thickness on magnetic anisotropy in MgO/Fe/Cr/MgO buffer/MgO(001)

    Energy Technology Data Exchange (ETDEWEB)

    Kozioł-Rachwał, Anna, E-mail: a.koziolrachwal@aist.go.jp [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); Nozaki, Takayuki; Zayets, Vadym; Kubota, Hitoshi; Fukushima, Akio; Yuasa, Shinji [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Suzuki, Yoshishige [National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531 (Japan)

    2016-08-28

    The relationship between the magnetic properties and MgO buffer layer thickness d was studied in epitaxial MgO/Fe(t)/Cr/MgO(d) layers grown on MgO(001) substrate in which the Fe thickness t ranged from 0.4 nm to 1.1 nm. For 0.4 nm ≤ t ≤ 0.7 nm, a non-monotonic coercivity dependence on the MgO buffer thickness was shown by perpendicular magneto-optic Kerr effect magnetometry. For thicker Fe films, an increase in the buffer layer thickness resulted in a spin reorientation transition from perpendicular to the in-plane magnetization direction. Possible origins of these unusual behaviors were discussed in terms of the suppression of carbon contamination at the Fe surface and changes in the magnetoelastic anisotropy in the system. These results illustrate a method to control magnetic anisotropy in MgO/Fe/Cr/MgO(d) via an appropriate choice of MgO buffer layer thickness d.

  7. Ultraviolet spectra of Mg in liquid helium

    International Nuclear Information System (INIS)

    Moriwaki, Y.; Morita, N.

    1999-01-01

    Emission and absorption spectra of Mg atoms implanted in liquid helium have been observed in the ultraviolet region. We have presented a model of exciplex formation of Mg-He 10 and found that this model is more suitable for understanding the dynamics in the 3s3p 1 P→3s 21 S transition than the bubble model. (orig.)

  8. Physicochemical and microbiological evaluation of sun dried tomatoes in comparison with fresh tomatoes

    International Nuclear Information System (INIS)

    Sohail, M.

    2011-01-01

    The present study was conducted to evaluate the quality of sun dried tomatoes in comparison with fresh tomatoes. Fresh fully ripen tomatoes were washed and cut in thin slices with sterilized stainless steel knife and divided into two lots, one was taken as control and other was dipped in 3% potassium meta bisulfite solution for 5 minutes. The samples were spread over stainless steel trays covered with muslin cloth and kept in solar dehydrator for 5 days at 55 +- 2 deg. C. The physicochemical analyses were carried out in both dried and fresh (control) tomatoes. They were also analyzed microbiologically for bacterial and fugal count. Results showed that sun dried tomatoes are microbiologically safe. The values of moisture content and vitamin C of fresh and sun dried tomatoes statistically differ from each others at probability level of 5 %. The nutrient which is highly affected by sun drying is vitamin C. In fresh tomatoes it was 32.5 mg/100 g which is reduced to 24.6 mg/100 g after sun drying and further reduced to 15.86 mg/100 g during three months storage. The moisture content of the fresh tomatoes was 94.4% which decreased to 8.15% after drying, and then slowly increased to 9.95% in the three months storage. Statistically no major difference was found in the other nutrients during storage, which indicates that sun drying is nutritionally and microbiologically safe and can be used to preserve tomatoes and other fruits and vegetables for off season use. (author)

  9. Role of CeO2 promoter in NiO/α-Al2O3 catalyst for dry reforming of methane

    Science.gov (United States)

    Loc, Luu Cam; Phuong, Phan Hong; Tri, Nguyen

    2017-09-01

    A series of Ni/α-Al2O3 (NiAl) catalysts promoted by CeO2 was prepared by co-impregnation methods with content of (NiO+CeO2) being in the range of 10-30 wt%. The NiO:CeO2 weight ratio was fluctuated at 1:1, 1:2 and 1:3. Several techniques, including X-ray powder diffraction (XRD), Hydrogen temperature-programmed reduction (H2-TPR), and transmission electron microscopy (TEM) were used to investigate catalysts' physico-chemical properties. The activity of these catalysts in dry reforming of CH4 was investigated at temperature range of 550-800 °C. The results revealed that the most suitable CeO2 promoted Ni catalyst contained 20 wt% of (NiO+CeO2) and NiO:CeO2 weight ratio of 1:2. The best catalytic performance of catalyst [20(1Ni2Ce)Al] due to a better reducibility resulted in a higher amount of free small particle NiO. At 700 °C and CH4:CO2 molar ratio of 1:1, the conversion of CH4 and CO2 on the most suitable CeO2 promoted Ni catalyst reached 86% and 67%, respectively; H2 and CO selectivity of 90% and H2:CO molar ratio of 1.15 were obtained. Being similar to MgO [1], promoter CeO2 could improve catalytic activity of Ni/α-Al2O3 catalyst at a lower range of temperature. Besides, both MgO and CeO2 had a great impact on improving coke resistance of Ni catalysts. At higher temperature, the role of CeO2 as well as MgO in preventing coke formation on catalyst was clarified by temperature-programmed oxidation (TPO) technique. Coke amount formed after 30-h TOS on 20(1Ni2Ce) catalyst was found to be 22.18 mgC/gcat, being less than on non-promoted catalyst (36.75 mgC/gcat), but more than on 20(1Ni2Mg)Al one (5.25 mgC/gcat).

  10. A novel method to produce dry geopolymer cement powder

    Directory of Open Access Journals (Sweden)

    H.A. Abdel-Gawwad

    2016-04-01

    Full Text Available Geopolymer cement is the result of reaction of two materials containing aluminosilicate and concentrated alkaline solution to produce an inorganic polymer binder. The alkali solutions are corrosive and often viscous solutions which are not user friendly, and would be difficult to use for bulk production. This work aims to produce one-mix geopolymer mixed water that could be an alternative to Portland cement by blending with dry activator. Sodium hydroxide (SH was dissolved in water and added to calcium carbonate (CC then dried at 80 °C for 8 h followed by pulverization to a fixed particle size to produce the dry activator consisting of calcium hydroxide (CH, sodium carbonate (SC and pirssonite (P. This increases their commercial availability. The dry activator was blended with granulated blast-furnace slag (GBFS to produce geopolymer cement powder and by addition of water; the geopolymerization process is started. The effect of W/C and SH/CC ratio on the physico-mechanical properties of slag pastes was studied. The results showed that the optimum percent of activator and CC content is 4% SH and 5% CC, by the weight of slag, which give the highest physico-mechanical properties of GBFS. The characterization of the activated slag pastes was carried out using TGA, DTG, IR spectroscopy and SEM techniques.

  11. Dry-distillation of experimental animal wastes containing radioisotopes

    International Nuclear Information System (INIS)

    Miyatake, Hideo; Saito, Kazumi; Kurihara, Norio

    1988-01-01

    Mice were dry-distilled at 800deg C for 10 min, after [ 32 P]orthophosphate or L-[4,5- 3 H]leucine was intraperitoneally administered. Phosphorus-32 was quantitatively recovered in the residual solid, whereas 95% of 3 H was found in the distillate (condensed water). When 14 C (L-[U- 14 C]malic acid or L-[U- 14 C]leucine) was administered to mice and they were dry-distilled, 14 C-radioactivity was distributed into two fractions; residual solid and exhaust gas. In these cases, the recovery percentage of 14 C in residual solid was not very high but increased as the treating temperature decreased. It reached about 40% of the administered 14 C at 400deg C for 120 min. By the dry-distillation of animals, their weight was reduced to about 10% in every animal tested (mice, rats and rabbits). The volume was reduced to about 20% in cases of mice and rats, and about 30% in case of rabbits. It was concluded that the dry-distillation can be useful as a pre-treatment for disposal of animal wastes containing radioisotopes. (author)

  12. Effect of freeze-dried leek powder (FDLP) and nitrite level on processing and quality characteristics of fermented sausages.

    Science.gov (United States)

    Tsoukalas, D S; Katsanidis, E; Marantidou, S; Bloukas, J G

    2011-02-01

    Fermented sausages were produced with 0.84% and 1.68% freeze-dried leek powder (FDLP), providing 75 and 150 mg/kg NaNO(3), respectively, and three levels of added nitrite (0, 75, and 150 mg/kg NaNO(2). A control treatment was also produced with 150 mg/kg NaNO(2). Sausages with FDLP were darker and yellower (pnitrite. Copyright © 2010 Elsevier Ltd. All rights reserved.

  13. Novel strip-cast Mg/Al clad sheets with excellent tensile and interfacial bonding properties.

    Science.gov (United States)

    Kim, Jung-Su; Lee, Dong Ho; Jung, Seung-Pill; Lee, Kwang Seok; Kim, Ki Jong; Kim, Hyoung Seop; Lee, Byeong-Joo; Chang, Young Won; Yuh, Junhan; Lee, Sunghak

    2016-06-01

    In order to broaden industrial applications of Mg alloys, as lightest-weight metal alloys in practical uses, many efforts have been dedicated to manufacture various clad sheets which can complement inherent shortcomings of Mg alloys. Here, we present a new fabrication method of Mg/Al clad sheets by bonding thin Al alloy sheet on to Mg alloy melt during strip casting. In the as-strip-cast Mg/Al clad sheet, homogeneously distributed equi-axed dendrites existed in the Mg alloy side, and two types of thin reaction layers, i.e., γ (Mg17Al12) and β (Mg2Al3) phases, were formed along the Mg/Al interface. After post-treatments (homogenization, warm rolling, and annealing), the interfacial layers were deformed in a sawtooth shape by forming deformation bands in the Mg alloy and interfacial layers, which favorably led to dramatic improvement in tensile and interfacial bonding properties. This work presents new applications to multi-functional lightweight alloy sheets requiring excellent formability, surface quality, and corrosion resistance as well as tensile and interfacial bonding properties.

  14. The subtle attractions of dry vault storage

    International Nuclear Information System (INIS)

    Ealing, C.J.

    1993-01-01

    Utilities in the United States of America, Scotland and Hungary have all adopted dry vault technology in their plans for spent fuel storage. This article looks at what makes dry storage an attractive option. (author)

  15. ORDERED WEIGHTED DISTANCE MEASURE

    Institute of Scientific and Technical Information of China (English)

    Zeshui XU; Jian CHEN

    2008-01-01

    The aim of this paper is to develop an ordered weighted distance (OWD) measure, which is thegeneralization of some widely used distance measures, including the normalized Hamming distance, the normalized Euclidean distance, the normalized geometric distance, the max distance, the median distance and the min distance, etc. Moreover, the ordered weighted averaging operator, the generalized ordered weighted aggregation operator, the ordered weighted geometric operator, the averaging operator, the geometric mean operator, the ordered weighted square root operator, the square root operator, the max operator, the median operator and the min operator axe also the special cases of the OWD measure. Some methods depending on the input arguments are given to determine the weights associated with the OWD measure. The prominent characteristic of the OWD measure is that it can relieve (or intensify) the influence of unduly large or unduly small deviations on the aggregation results by assigning them low (or high) weights. This desirable characteristic makes the OWD measure very suitable to be used in many actual fields, including group decision making, medical diagnosis, data mining, and pattern recognition, etc. Finally, based on the OWD measure, we develop a group decision making approach, and illustrate it with a numerical example.

  16. Assessment of thermal load on transported goats administered with ascorbic acid during the hot-dry conditions

    Science.gov (United States)

    Minka, N. S.; Ayo, J. O.

    2012-03-01

    The major factor in the induction of physiological stress during road transportation of livestock is the complex fluctuations of the thermal transport microenvironment, encountered when animals are transported across different ecological zones. Recommended guidelines on optimum "on-board" conditions in which goats should be transported are lacking, and there are no acceptable ranges and limits for the thermal loads to which goats may be subjected during long-distance road transportation in hot-dry conditions. Panting score (PS), rectal temperature (RT), heart rate (HR) and respiratory rate (RR) were employed as reliable stress indices to assess the effects of different thermal loads, measured as temperature humidity index (THI), encountered in the vehicle during 12 h of road transportation of 40 goats, and to suggest the administration of 100 mg/kg body weight of ascorbic acid (AA) as an ameliorating agent. The results obtained showed that the PS, RT, HR and RR rose above normal reference values with increase in the THI and journey duration. The rise in PS value, which is a visual indicator of the severity of thermal load, was the most pronounced. The results suggest that values of THI in the vehicle up to 94.6 constitute no risk, while at of 100 it presents a moderate risk and above 100 may result in severe stress. The relationships between the thermal load and the physiological variables were positive and significant ( P goats. The results demonstrated that administration of 100 mg/kg body weight of AA before road transportation mitigated the risk of adverse effects of high THI values and other stress factors due to road transportation in goats.

  17. Accelerating oak air drying by presurfacing

    Science.gov (United States)

    W. T. Simpson; R. C. Baltes

    1972-01-01

    A comparison was made between the air-drying rates of rough and presurfaced northern red oak and white oak. In both species, the presurfaced material was about 1/8 inch thinner than the rough material and dried faster than the rough material. The reduction in drying time depends on the method of analyzing the drying curves, but is slightly less than 10 percent.

  18. Latest Apple Drying Technologies: A Review

    OpenAIRE

    ÖZDEMİR, Yasin; SAYIN, Emir Olcay; KURULTAY, Şefik

    2009-01-01

    Drying is known as one of the oldest preservation methods and can be applicable to many fruits. Sun drying of apple has been known from ancient times. However, this technique is weather-dependent and has contamination problems such as dust, soil, sand particles and insects. Hot air drying of apples has low energy efficiency and requires longer drying period. The desire to eliminate these problems, prevent quality loss, and achieve fast and effective thermal processing has resulted in an incre...

  19. Effects of Aging in Dry Eye

    Science.gov (United States)

    de Paiva, Cintia S.

    2017-01-01

    Dry eye affects millions of people worldwide and causes eye well recognized risk factors for dry eye. Anatomical and inflammation-induced age-related changes affect all components of the lacrimal gland functional unit, inclusive of lacrimal gland, conjunctiva, meibomian gland and compromise ocular surface health. There is increased evidence that inflammation plays a role in dry eye. This review will summarize the current knowledge about aging and dry eye, inclusive of lessons learned from animal models and promising therapies. PMID:28282314

  20. Selective dry cow treatment in dairy cows

    OpenAIRE

    Scherpenzeel, C.G.M.

    2017-01-01

    In the dairy industry, udder health is associated with mastitis management, of which blanket dry cow treatment has been an important part for decades. To prevent the udder from new intramammary infections during the dry period, the use of blanket dry cow treatment has been advocated for more than 50 years as part of the five-point mastitis prevention program. The goal of dry cow treatment is to reduce the prevalence of intramammary infections by eliminating infections already present at dryin...

  1. Impact of dry eye on work productivity

    Directory of Open Access Journals (Sweden)

    Yamada M

    2012-10-01

    Full Text Available Masakazu Yamada, Yoshinobu Mizuno, Chika ShigeyasuNational Institute of Sensory Organs, National Hospital Organization Tokyo Medical Center, Tokyo, JapanBackground: The purpose of this study was to evaluate the impact of dry eye on work productivity of office workers, especially in terms of presenteeism.Methods: A total of 396 individuals aged ≥20 years (258 men and 138 women, mean age 43.4 ± 13.0 years were recruited through an online survey. Data from 355 responders who did not have missing values were included in the analysis. They were classified into the following four groups according to the diagnostic status and subjective symptoms of dry eye: a definite dry eye group; a marginal dry eye group; a self-reported dry eye group; and a control group. The impact of dry eye on work productivity was evaluated using the Japanese version of the Work Limitations Questionnaire. The cost of work productivity loss associated with dry eye and the economic benefits of providing treatment for dry eye were also assessed.Results: The degree of work performance loss was 5.65% in the definite dry eye group, 4.37% in the marginal dry eye group, 6.06% in the self-reported dry eye group, and 4.27% in the control group. Productivity in the self-reported dry eye group was significantly lower than that in the control group (P < 0.05. The annual cost of work productivity loss associated with dry eye was estimated to be USD 741 per person.Conclusion: Dry eye impairs work performance among office workers, which may lead to a substantial loss to industry. Management of symptoms of dry eye by providing treatment may contribute to improvement in work productivity.Keywords: burden of disease, dry eye, presenteeism, quality of life

  2. Effect of Hot Water Blanching Time and Drying Temperature on the Thin Layer Drying Kinetics of and Anthocyanin Degradation in Black Carrot (Daucus carota L. Shreds

    Directory of Open Access Journals (Sweden)

    Umar Garba

    2015-01-01

    Full Text Available This study was conducted to investigate the eff ect of blanching treatment (98 °C for 3 and 6 min and air drying temperature of 40, 50 and 60 °C on the thin layer drying characteristics such as drying time, drying rate constant, effective moisture diffusivity and activation energy, as well as on anthocyanin content of black carrot shreds. It was observed that drying temperature aff ected the drying rate but blanching did not have an eff ect on drying time. Three thin layer drying models, i.e. Page, Lewis and Henderson-Pabis were evaluated. The goodness of these models was evaluated based on the coefficient of determination (R2, root mean square error, reduced chi square (χ2 and standard error. Page model showed the best fit to the drying data. The effective diffusivity ranges of 1.4·10–9 to 2.6·10–9 m2/s, 1.3·10–9 to 2.1·10–9 m2/s and 1.5·10–9 to 2.2·10–9 m2/s aft er 3 or 6 min of blanching and control samples respectively were calculated using Fick’s second law. The activation energy of 37.5, 26.0 and 34.6 kJ/(mol·K of the control samples and samples blanched for 3 or 6 min respectively was determined from the Arrhenius plot. The blanching treatment affected the anthocyanin content to a great extent. The anthocyanin content of (231.7±2.9 and (278.8±7.8 mg per 100 g was recorded in samples blanched for 3 and 6 min and then dried at 60 °C, and (153.0±4.3 and (247.0±5.5 mg per 100 g was recorded at 40 °C as compared to the control of (580.1±1.3 at 60 °C and (466.7±1.1 mg per 100 g at 40 °C.

  3. Amorphous phase formation in intermetallic Mg2Ni alloy synthesized by ethanol wet milling

    International Nuclear Information System (INIS)

    Wang, H.-W.; Chyou, S.-D.; Wang, S.-H.; Yang, M.-W.; Hsu, C.-Y.; Tien, H.-C.; Huang, N.-N.

    2009-01-01

    The hydriding/dehydriding properties of an intermetallic Mg 2 Ni alloy synthesized by wet ball milling in ethanol have been investigated. The appearance of the particle surface after different milling methods is one obvious difference. The alloyed powders prepared by either dry milling or wet milling under ethanol were characterized for phase content by X-ray diffractometer (XRD). The results show that two broad diffuse peaks, which are an ionic-organic-Mg amorphous material, appear in addition to the nickel element peaks. This unexpected amorphous phase has the special hydrogen absorbing/desorbing features.

  4. The preliminary study of the quench protection of an MgB2

    Science.gov (United States)

    Juster, F. P.; Berriaud, C.; Bonelli, A.; Pasquet, R.; Przybilski, H.; Schild, T.; Scola, L.

    2014-01-01

    In the framework of general studies currently carried out at CEA/Saclay in collaboration with Sigmaphi Company on dry MgB2 magnet operating at 10 K and medium range field, 1 T up to 4 T., we plan to build a prototype-coil with a commercial MgB2 wire. This coil, the nominal axial magnetic field of which is 1 tesla, will be placed in a 3 teslas background field generated by a classical NbTi coil. This paper deals with the preliminary quench protection studies including stability and quench propagation modeling.

  5. Quantification of multiple elements in dried blood spot samples

    DEFF Research Database (Denmark)

    Pedersen, Lise; Andersen-Ranberg, Karen; Hollergaard, Mads

    2017-01-01

    BACKGROUND: Dried blood spots (DBS) is a unique matrix that offers advantages compared to conventional blood collection making it increasingly popular in large population studies. We here describe development and validation of a method to determine multiple elements in DBS. METHODS: Elements were...... in venous blood. Samples with different hematocrit were spotted onto filter paper to assess hematocrit effect. RESULTS: The established method was precise and accurate for measurement of most elements in DBS. There was a significant but relatively weak correlation between measurement of the elements Mg, K...

  6. Polyfloral, linden and acacia honeys with dried cherries after three months of storage - antioxidant and sensory evaluation

    Directory of Open Access Journals (Sweden)

    Vulić Jelena J.

    2015-01-01

    Full Text Available Samples of three types of honey: polyfloral (PH, linden (LH and acacia (AH, without and with addition of dried cherries (40% were analyzed before and after three months of storage. The total phenol (TPh, flavonoid (TFd and anthocyanin (TAn contents, antioxidant activities and sensory properties of honeys with and without the addition of dry cherries were evaluated. TPh and TFd increased with addition of dried cherries to the honey, while enriched honeys showed high TAn. The LH sample with dried cherries showed the highest anthocyanins content (41.41mgCGE/100g. The antioxidant activity increased with addition of dried cherries in honey in the DPPH• test and reducing power. The PH and enriched PH exibited the best antiradical activity compared to LH and AH. The EC50 DPPH values were: 23.81 for PH and 24.19 mg/mL for PH, while the EC50 DPPH were: 1.16 mg/mL for PH40 and 1.18 mg/mL for PH40s. RP0.5 values were: 57.00 mg/mL for PH40 and 56.00 mg/ml for PH40s, while RP0.5 were: 15.05 mg/mL for PH40 and 15.18 mg/mL for PH40s. The statistical analysis showed that TPh, TFd and TAn, and antioxidant activity of honeys and enriched honeys showed significant correlation. Sensory analysis of honey with dried cherries, before and after storage, indicated very good sensory characteristics.

  7. energetic performance analysis of drying agricultural products

    African Journals Online (AJOL)

    user

    ... a solar box dryer aided by a tracking device, and open air drying over an effective total drying time of 6 hours each day, for 5 days. ... cost in the use of modern dryers. Drying can be ..... speed, cloud cover and humidity respectively. 4.2 Solar ...

  8. Drying principles and theory: An overview

    International Nuclear Information System (INIS)

    Ekechukwu, O.V.

    1995-10-01

    A comprehensive review of the fundamental principles and theories governing the drying process is presented. Basic definitions are given. The development of contemporary models of drying of agricultural products are traced from the earliest reported sorption and moisture equilibrium models, through the single kernel of product models to the thin layer and deep bed drying analysis. (author). 29 refs, 10 figs

  9. Selective dry cow treatment in dairy cows

    NARCIS (Netherlands)

    Scherpenzeel, C.G.M.

    2017-01-01

    In the dairy industry, udder health is associated with mastitis management, of which blanket dry cow treatment has been an important part for decades. To prevent the udder from new intramammary infections during the dry period, the use of blanket dry cow treatment has been advocated for more than 50

  10. Economic optimization of selective dry cow treatment

    NARCIS (Netherlands)

    Scherpenzeel, C G M; Hogeveen, H; Maas, L; Lam, T J G M

    2018-01-01

    The objective of this study was to develop a mathematical model to identify a scenario with the lowest costs for mastitis associated with the dry period while restricting the percentage of cows to be dried off with dry cow antimicrobials. Costs of clinical and subclinical mastitis as well as

  11. Albendazole Microparticles Prepared by Spray Drying Technique ...

    African Journals Online (AJOL)

    Purpose: To enhance the dissolution of albendazole (ABZ) using spray-drying technique. Method: ABZ binary mixtures with Kollicoat IR® (KL) and polyvinyl pyrrolidone (PVP) in various drug to polymer ratios (1: 1, 1: 2 and 1; 4) were prepared by spray-drying. The spray-dried particles were characterized for particle shape, ...

  12. Drying characteristics of willow chips and stems

    NARCIS (Netherlands)

    Gigler, J.K.; Loon, van W.K.P.; Seres, I.; Meerdink, G.; Coumans, W.J.

    2000-01-01

    In supply chains of willow (Salix viminalis) biomass to energy plants, drying is advisable in order to enable safe long-term storage, increase boiler efficiency and reduce gaseous emissions. To gain insight into the drying process, drying characteristics of willow chips and stems were investigated

  13. Quality drying of hardwood lumber : guidebook -- checklist

    Science.gov (United States)

    R. S. Boone; M. R. Milota; J. D. Danielson; D. W. Huber

    The IMPROVE Lumber Drying Program is intended to increase awareness of the lumber drying system as a critical component in the manufacture of quality lumber. One objective of the program is to provide easy-to-use tools that a kiln operator can use to maintain an efficient kiln operation and therefore improve lumber drying quality. This report is one component of the...

  14. Quality drying of softwood lumber : guidebook - checklist

    Science.gov (United States)

    M. R. Milota; J. D. Danielson; R. S. Boone; D. W. Huber

    The IMPROVE Lumber Drying Program is intended to increase awareness of the lumber drying system as a critical component in the manufacture of quality lumber. One objective of the program is to provide easy-to-use tools that a kiln operator can use to maintain an efficient kiln operation and therefore contribute to lumber drying quality. This report is one component of...

  15. Inert carrier drying and coating process

    International Nuclear Information System (INIS)

    1980-01-01

    An inert carrier process is described for drying radioactive (particularly low level) waste material and for incorporating the dry material into a binder matrix from which the dried material will not be leached. Experimental details, and examples of the carrier and binder materials, are given. (U.K.)

  16. Kinetics and Quality of Microwave-Assisted Drying of Mango (Mangifera indica

    Directory of Open Access Journals (Sweden)

    Ernest Ekow Abano

    2016-01-01

    Full Text Available The effect of microwave-assisted convective air-drying on the drying kinetics and quality of mango was evaluated. Both microwave power and pretreatment time were significant factors but the effect of power was more profound. Increase in microwave power and pretreatment time had a positive effect on drying time. The nonenzymatic browning index of the fresh samples increased from 0.29 to 0.60 while the ascorbic acid content decreased with increase in microwave power and time from 3.84 mg/100g to 1.67 mg/100g. The effective moisture diffusivity varied from 1.45 × 10−9 to 2.13 × 10−9 m2/s for microwave power range of 300-600 W for 2 to 4 minutes of pretreatment. The Arrhenius type power-dependent activation energy was found to be in the range of 8.58–17.48 W/mm. The fitting of commonly used drying models to the drying data showed the Midilli et al. model as the best. Microwave power of 300 W and pretreatment time of 4 minutes emerged as the optimum conditions prior to air-drying at 7°C. At this ideal condition, the energy savings as a result of microwave application was approximately 30%. Therefore, microwave-assisted drying should be considered for improved heat and mass transfer processes during drying to produce dried mangoes with better quality.

  17. Antidepressants and Weight Gain

    Science.gov (United States)

    ... 2015;37:46. Blumenthal SR, et al. An electronic health records study of long-term weight gain following antidepressant ... your agreement to the Terms and Conditions and Privacy Policy linked below. Terms and Conditions Privacy Policy ...

  18. Weight gain - unintentional

    Science.gov (United States)

    ... diabetes Hormone changes or medical problems can also cause unintentional weight gain. This may be due to: Cushing syndrome Underactive thyroid, or low thyroid (hypothyroidism) Polycystic ovary syndrome Menopause Pregnancy Bloating, or swelling ...

  19. Weight and psychiatry

    African Journals Online (AJOL)

    Adele

    Beyond the physical aspects of weight, the psychological mean- ing sees the virtues of ... sion in the development and persistence of adolescent obesity. Pediat- rics 2002 ... or secondary as in mood, anxiety or psychotic disorders. II. a related.

  20. birth-weight infants

    African Journals Online (AJOL)

    including the CRIB (Clinical Risk Index for Babies) score, in a local ... these babies for expensive tertiary care. Subjects. ... patient numbers, the tendency is simply to increase the ... included birth weight, gestational age, 5-minute Apgar score ...

  1. Weight loss and alcohol

    Science.gov (United States)

    ... Maclean JC. Alcohol consumption and body weight. Health Econ . 2010;19(7):814-832. PMID: 19548203 www. ... member of Hi-Ethics and subscribes to the principles of the Health on the Net Foundation (www. ...

  2. Optical absorption and thermoluminescence in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature

    International Nuclear Information System (INIS)

    Delgado, L.

    1984-01-01

    Optical absorption and thermoluminescence (TL) studies in Mg O, Mg O:Ni and Mg O:Li irradiated at room temperature are presented. In pure Mg O the thermal annihilation of Fe3+ by recombination with thermally released electrons at ∼ 90 and 175 degree centigree and the V center annealing by hole release up to 100 degree centigree cause the observed glow peaks at these temperatures. The TL excitation spectrum shows two maxima at 245 nm (electron center) and 288 nm (Fe3+). In Mg O:Ni X irradiation induces Fe 2 + →- Fe 3 + and Ni 2 + → Ni 3 + oxidations. Two TL emission bands centered at 110 degree centigree (red) and 80 o C (green) are assigned to electron release and their recombination at Fe 3 + and Ni 3 + respectively. In Mg O:Li two TL emission bands, one blue (430 nm) and the other red (730 nm) with excitation maxima at 245 nm (electron center) and 200 nm (hole center) respectively are observed. No V-center formation was detected in both Ni and Li doped samples. (Author) 42 refs

  3. Neural network potential for Al-Mg-Si alloys

    Science.gov (United States)

    Kobayashi, Ryo; Giofré, Daniele; Junge, Till; Ceriotti, Michele; Curtin, William A.

    2017-10-01

    The 6000 series Al alloys, which include a few percent of Mg and Si, are important in automotive and aviation industries because of their low weight, as compared to steels, and the fact their strength can be greatly improved through engineered precipitation. To enable atomistic-level simulations of both the processing and performance of this important alloy system, a neural network (NN) potential for the ternary Al-Mg-Si has been created. Training of the NN uses an extensive database of properties computed using first-principles density functional theory, including complex precipitate phases in this alloy. The NN potential accurately reproduces most of the pure Al properties relevant to the mechanical behavior as well as heat of solution, solute-solute, and solute-vacancy interaction energies, and formation energies of small solute clusters and precipitates that are required for modeling the early stage of precipitation and mechanical strengthening. This success not only enables future detailed studies of Al-Mg-Si but also highlights the ability of NN methods to generate useful potentials in complex alloy systems.

  4. Hydrothermal synthesis and corrosion behavior of the protective coating on Mg-2Zn-Mn-Ca-Ce alloy

    Directory of Open Access Journals (Sweden)

    Dan Song

    2016-12-01

    Full Text Available Protective coatings were synthesized on the Mg-2Zn-Mn-Ca-Ce Mg alloy through the hydrothermal method with de-ionized water as the reagent. The coatings were composed of Mg hydroxide, generally uniform and compact. Hydrogen evolution tests and electrochemical tests in the Hanks’ solution demonstrated that the Mg(OH2 coatings effectively decreased the bio-degradation rate of the Mg alloy substrate. Microstructure observation showed that the coating formation on the secondary phases was more difficult than that on the α-Mg matrix, which led to micro cracks and pores on the secondary phases after drying. Over synthesizing time, the coating layer on secondary phases gradually becomes more compact and uniform. Meanwhile, owing to the thicker and more compact coatings, the corrosion resistance and protective efficiency were significantly improved with longer synthesizing time as well.

  5. Mg2BIV: Narrow Bandgap Thermoelectric Semiconductors

    Science.gov (United States)

    Kim, Il-Ho

    2018-05-01

    Thermoelectric materials can convert thermal energy directly into electric energy and vice versa. The electricity generation from waste heat via thermoelectric devices can be considered as a new energy source. For instance, automotive exhaust gas and all industrial processes generate an enormous amount of waste heat that can be converted to electricity by using thermoelectric devices. Magnesium compound Mg2BIV (BIV = Si, Ge or Sn) has a favorable combination of physical and chemical properties and can be a good base for the development of new efficient thermoelectrics. Because they possess similar properties to those of group BIV elemental semiconductors, they have been recognized as good candidates for thermoelectric applications. Mg2Si, Mg2Ge and Mg2Sn with an antifluorite structure are narrow bandgap semiconductors with indirect band gaps of 0.77 eV, 0.74 eV, and 0.35 eV, respectively. Mg2BIV has been recognized as a promising material for thermoelectric energy conversion at temperatures ranging from 500 K to 800 K. Compared to other thermoelectric materials operating in the similar temperature range, such as PbTe and filled skutterudites, the important aspects of Mg2BIV are non-toxic and earth-abundant elements. Based on classical thermoelectric theory, the material factor β ( m* / m e)3/2μκ L -1 can be utilized as the criterion for thermoelectric material selection, where m* is the density-of-states effective mass, me is the mass of an electron, μ is the carrier mobility, and κL is the lattice thermal conductivity. The β for magnesium silicides is 14, which is very high compared to 0.8 for iron silicides, 1.4 for manganese silicides, and 2.6 for silicon-germanium alloys. In this paper, basic phenomena of thermoelectricity and transport parameters for thermoelectric materials were briefly introduced, and thermoelectric properties of Mg2BIV synthesized by using a solid-state reaction were reviewed. In addition, various Mg2BIV compounds were discussed

  6. Large-area thin self-supporting carbon foils with MgO coatings

    Science.gov (United States)

    Stolarz, Anna; Maier-Komor, Peter

    2002-03-01

    Large area self-supporting carbon foils in the thickness of range of 8-22 μg/cm 2, coated with approximately 4 μg/cm 2 MgO have been prepared by e-gun evaporation. They were mounted on frames with apertures of 130 cm 2. Problems related to the parting agent preparation, floating procedure, and mounting onto frames are discussed. Special precautions necessary to avoid damage during foil drying, storage and transportation are suggested.

  7. Zinder: a city running dry.

    Science.gov (United States)

    Price, T

    1993-01-01

    In the West African Sahel lies the old Hausa city of Zinder, Niger. Since the last few decades, it has constantly faced considerable population growth (19,300-119,8000 between 1960 and 1980) while its acute problems with the water supply are increasing. The dry regional climate compounds the problems. In the past, Zinder was a trade center between northern and sub-Saharan Africa as well as being the colonial capital of Niger (1911-26). Its economic and political position has fallen greatly with independence. Lower than average rainfall and the disastrous droughts of the 1970s and 1980s have seriously diminished the region's economic base, e.g., the average annual rainfall in 1930-60 was 535 mm, but by the 1980s, it was only 355 mm. Zinder sits on an elevated, rocky hill which is encircled by dry river valleys and there are no major permanent bodies of water in the vicinity. Impenetrable layers of stone prevent the digging of wells within the city, so the city depends on wells in nearby valleys. The reduced rainfall hinders replenishment of the aquifer, resulting in a drop in the availability of water for daily consumption from 6500 to 3500 sq m. Per capita water consumption in Zinder is much lower than the national average (55 1/day vs. about 100 1/day). The drought in 1992 caused per capita consumption to fall to 29 1/day, just barely above the minimal standards for private use in urban areas of 20 1/person/day. To further compound the problem, 20 villages in Zinder's environs, some villages with a population of 5000, people, rely on the same water system. Zinder serves as a refuge for the regional population in drought years and during the yearly dry season. Promised international financing cannot resolve Zinder's problems at a realistic cost.

  8. Impact of dry eye on work productivity.

    Science.gov (United States)

    Yamada, Masakazu; Mizuno, Yoshinobu; Shigeyasu, Chika

    2012-01-01

    The purpose of this study was to evaluate the impact of dry eye on work productivity of office workers, especially in terms of presenteeism. A total of 396 individuals aged ≥20 years (258 men and 138 women, mean age 43.4 ± 13.0 years) were recruited through an online survey. Data from 355 responders who did not have missing values were included in the analysis. They were classified into the following four groups according to the diagnostic status and subjective symptoms of dry eye: a definite dry eye group; a marginal dry eye group; a self-reported dry eye group; and a control group. The impact of dry eye on work productivity was evaluated using the Japanese version of the Work Limitations Questionnaire. The cost of work productivity loss associated with dry eye and the economic benefits of providing treatment for dry eye were also assessed. The degree of work performance loss was 5.65% in the definite dry eye group, 4.37% in the marginal dry eye group, 6.06% in the self-reported dry eye group, and 4.27% in the control group. Productivity in the self-reported dry eye group was significantly lower than that in the control group (P work productivity loss associated with dry eye was estimated to be USD 741 per person. Dry eye impairs work performance among office workers, which may lead to a substantial loss to industry. Management of symptoms of dry eye by providing treatment may contribute to improvement in work productivity.

  9. Preparation and provisional validation of a large size dried spike: Batch SAL-9931

    International Nuclear Information System (INIS)

    Jammet, G.; Zoigner, A.; Doubek, N.; Grabmueller, G.; Bagliano, G.

    1990-05-01

    To determine uranium and plutonium concentration using isotope dilution mass spectrometry, weighed aliquands of a synthetic mixture containing about 2 mg of Pu (with a 239 Pu abundance of about 98%) and 40 mg of U (with a 235 U enrichment of about 19%) have been prepared and verified by SAL to be used to spike samples of concentrated spent fuel solutions with a high burn-up and a low 235 U enrichment. The advantages of such a Large Size Dried (LSD) Spike have been pointed out elsewhere and proof of the usefulness in the field reported. Certified Reference Materials Pu-NBL-126, natural U-NBS-960 and 93% enriched U-NBL-116 were used to prepare a stock solution containing 1.8 mg/ml of Pu and 37.3 mg/ml of 19.4% enriched U. Before shipment to the Reprocessing Plant, aliquands of the stock solution are dried to give Large Size Dried Spikes which resist shocks encountered during transportation, so that they can readily be recovered quantitatively at the plant. This paper describes the preparation and the validation of a Large Size Dried Spike which is intended to be used as a common spike by the plant operator, the national and the IAEA inspectorates. 6 refs, 7 tabs

  10. Influence of Fermentation and Drying Materials on the Contamination of Cocoa Beans by Ochratoxin A

    Directory of Open Access Journals (Sweden)

    Sébastien Djédjé Dano

    2013-11-01

    Full Text Available Ochratoxin A (OTA is a mycotoxin produced mainly by species of Aspergillus and Penicillium. Contamination of food with OTA is a major consumer health hazard. In Cote D’Ivoire, preventing OTA contamination has been the subject of extensive study. The current study was conducted to evaluate the influence of fermentation and drying materials on the OTA content in cocoa. For each test, 7000 intact cocoa pods were collected, split open to remove the beans, fermented using 1 of 3 different materials, sun-dried on 1 of 3 different platform types and stored for 30 days. A total of 22 samples were collected at each stage of post-harvesting operations. The OTA content in the extracted samples was then quantified by high-performance liquid chromatography. OTA was detected in beans at all stages of post-harvesting operations at varying levels: pod-opening (0.025 ± 0.02 mg/kg, fermentation (0.275 ± 0.2 mg/kg, drying (0.569 ± 0.015 mg/kg, and storage (0.558 ± 0.04 mg/kg. No significant relationships between the detected OTA level and the materials used in the fermentation and drying of cocoa were observed.

  11. Dry-cleaning of graphene

    International Nuclear Information System (INIS)

    Algara-Siller, Gerardo; Lehtinen, Ossi; Kaiser, Ute; Turchanin, Andrey

    2014-01-01

    Studies of the structural and electronic properties of graphene in its pristine state are hindered by hydrocarbon contamination on the surfaces. Also, in many applications, contamination reduces the performance of graphene. Contamination is introduced during sample preparation and is adsorbed also directly from air. Here, we report on the development of a simple dry-cleaning method for producing large atomically clean areas in free-standing graphene. The cleanness of graphene is proven using aberration-corrected high-resolution transmission electron microscopy and electron spectroscopy

  12. Dry-cleaning of graphene

    Energy Technology Data Exchange (ETDEWEB)

    Algara-Siller, Gerardo [Central Facility for Electron Microscopy, Group of Electron Microscopy of Materials Science, Ulm University, Albert-Einstein-Allee 11, Ulm 89081 (Germany); Department of Chemistry, Technical University Ilmenau, Weimarer Strasse 25, Ilmenau 98693 (Germany); Lehtinen, Ossi; Kaiser, Ute, E-mail: ute.kaiser@uni-ulm.de [Central Facility for Electron Microscopy, Group of Electron Microscopy of Materials Science, Ulm University, Albert-Einstein-Allee 11, Ulm 89081 (Germany); Turchanin, Andrey [Faculty of Physics, University of Bielefeld, Universitätsstr. 25, Bielefeld 33615 (Germany)

    2014-04-14

    Studies of the structural and electronic properties of graphene in its pristine state are hindered by hydrocarbon contamination on the surfaces. Also, in many applications, contamination reduces the performance of graphene. Contamination is introduced during sample preparation and is adsorbed also directly from air. Here, we report on the development of a simple dry-cleaning method for producing large atomically clean areas in free-standing graphene. The cleanness of graphene is proven using aberration-corrected high-resolution transmission electron microscopy and electron spectroscopy.

  13. Dry storage of spent fuel

    International Nuclear Information System (INIS)

    Jeffrey, R.

    1993-01-01

    Scottish Nuclear's plans to build and operate dry storage facilities at each of its two nuclear power station sites in Scotland are explained. An outline of where waste materials arise as part of the operation and decommissioning of nuclear power stations, the volumes for each category of high-, intermediate-and low-level wastes and the costs involved are given. The present procedure for the spent fuels from Hunterston-B and Torness stations is described and Scottish Nuclear's aims of driving output up and costs down are studied. (UK)

  14. Dry deposition on urban surfaces

    International Nuclear Information System (INIS)

    Roed, J.

    1985-01-01

    In order to facilitate developing a model for deposition in urban areas, beryllium-7, created by cosmic radiation and fall-out cesium-137, have been used as tracers in measurements designed to find the dry deposition velocity on building surfaces. A literature review has revealed that very little work has been done on deposition in urban areas; therefore, a major effort on meausring the deposition parameter is needed to construct reliable models in this field. Deposition velocities in the range from 0.001-0.04 cm/s have been found. (author)

  15. Dry containment of radioactive materials

    International Nuclear Information System (INIS)

    Williams, C.E.

    1980-01-01

    A cask for the dry containment of radioactive fuel elements is described. The cask has a cover which contains valved drain and purge passageways. These passageways are sealed by after purge cover seals which are clamped over them and to the outer surface of the cover. The cover seals are tested by providing them with a pair of concentric ring seal elements squeezed between the cover seal and the outer surface of the cover and by forcing a gas under pressure into the annular region between the seal element

  16. Dry decontamination for tritiated wastes

    International Nuclear Information System (INIS)

    Shi Zhengkun; Wu Tao; Dan Guiping; Xie Yun

    2009-01-01

    To aim at decontamination of tritiated wastes, we have developed and fabricated a dry tritium decontamination system, which is designed to reduce tritium surface contamination of various alloy by UV, ozone and heating. The result indicates that the elevation of temperature can obviously improve decontamination effect. With 3 h irradiation by 365 nm UV at 220 degree C, it has a decontamination rate of 99% to stainless steel surface. Ozone can more obviously improve decontamination effect when metal was heated. Ozone has a decontamination effect beyond 95% to stainless steel, aluminum and brass at 220 degree C. Tritium surface concentration of metal has a little increase after decontamination. (authors)

  17. Development and Characterisation of Aluminium Matrix Nanocomposites AlSi10Mg/MgAl2O4 by Laser Powder Bed Fusion

    Directory of Open Access Journals (Sweden)

    Giulio Marchese

    2018-03-01

    Full Text Available Recently, additive manufacturing techniques have been gaining attention for the fabrication of parts from aluminium alloys to composites. In this work, the processing of an AlSi10Mg based composite reinforced with 0.5% in weight of MgAl2O4 nanoparticles through laser powder bed fusion (LPBF process is presented. After an initial investigation about the effect of process parameters on the densification levels, the LPBF materials were analysed in terms of microstructure, thermo-mechanical and mechanical properties. The presence of MgAl2O4 nanoparticles involves an increment of the volumetric energy density delivered to the materials, in order to fabricate samples with high densification levels similar to the AlSi10Mg samples. However, the application of different building parameters results in modifying the size of the cellular structures influencing the mechanical properties and therefore, limiting the strengthening effect of the reinforcement.

  18. Study of MgO transformation into MgF2 in the presence of CF2Cl2•

    Directory of Open Access Journals (Sweden)

    Vedyagin Aleksey A.

    2017-01-01

    Full Text Available Alkaline-earth metal oxide aerogels prepared by sol–gel method followed by autoclave drying are nanocrystalline mesoporous materials with high reactivity. Bulk solid-state reaction of MgO aerogels with CF2Cl2 takes place after a long induction period, during which the active sites are accumulated on the surface of the nanoparticles. It was found that vanadium addition has a promoting effect on this reaction accelerating the process of the active sites formation. A method for characterization of electron-acceptor sites by electron spin resonance spectroscopy using perylene as the spin probe was developed. A good correlation was observed between the rate of the CF2Cl2 destructive sorption and the concentration of weak electron-acceptor sites. Simplified models of such sites were suggested. The acid sites on the modified MgO surface were supposed to be originated from separation of the charged fragments resulting in the surface polarization. Uncompensated oxygen substitution for chlorine and/or fluorine ions leads to appearance of Lewis acid sites while HCl/HF chemisorption results in Bronsted acid sites formation.

  19. Effectiveness of hormone therapy for treating dry eye syndrome in postmenopausal women: a randomized trial.

    Science.gov (United States)

    Piwkumsribonruang, Narongchai; Somboonporn, Woraruk; Luanratanakorn, Patanaree; Kaewrudee, Srinaree; Tharnprisan, Piangjit; Soontrapa, Sugree

    2010-06-01

    The efficacy of hormone therapy (HT) on dry eye syndrome remains debatable. To study the efficacy of HT on dry eye syndrome. A randomized controlled, double blind, parallel group, community-based study in 42 post-menopausal patients was conducted. The patients had dry eye syndrome and were not taking any medications. They were assigned to one of two groups. Group A comprised 21 patients given transdermal 17 beta-estradiol (50 mg/day) and medroxy progesterone acetate (2.5 mg/day) continuously for three months and group B comprised 21 patients given both transdermal and oral placebo. Participants in the study were included for final analysis. The improvement of dry eye symptoms were measured by visual analog scale, tear secretion, intraocular pressure, corneal thickness, and tear breakup time determined before treatment and at 6 and 12 weeks of treatment. At 12 weeks, the number of patients who reported improvement of dry eye symptoms was greater in the HT group than that in the placebo group. However, the difference was not statistically significant (RR 0.25, 95% CI 0.04-2.80 and 0.60, 95% CI 0.33-2.03 in right and left eye, respectively). For other parameters, there was no significant difference between the two groups. According to the present study, there is no strong evidence to support the use of HT for treating dry eye syndrome. The limited number of participants included in the present study may have contributed to the insignificant effects.

  20. Single droplet drying for optimal spray drying of enzymes and probiotics

    NARCIS (Netherlands)

    Schutyser, M.A.I.; Perdana, J.A.; Boom, R.M.

    2012-01-01

    Spray drying is a mild and cost-effective convective drying method. It can be applied to stabilise heat sensitive ingredients, such as enzymes and probiotic bacteria, albeit in industrial practice for example freeze drying or freezing are often preferred. The reason is that optimum drying conditions

  1. Theoretical and practical aspects of aroma retention in spray drying and freeze drying

    NARCIS (Netherlands)

    Coumans, W.J.; Kerkhof, P.J.A.M.; Bruin, S.

    1994-01-01

    A review with 75 refs. on aroma loss in slab drying, spray drying and freeze drying. For many food products the presence of volatile aroma components is a prime quality feature. Upon drying part of these components may be lost, leading to unbalanced flavor patterns in the reconstituted product. The

  2. Dry Transfer Systems for Used Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Brett W. Carlsen; Michaele BradyRaap

    2012-05-01

    The potential need for a dry transfer system (DTS) to enable retrieval of used nuclear fuel (UNF) for inspection or repackaging will increase as the duration and quantity of fuel in dry storage increases. This report explores the uses for a DTS, identifies associated general functional requirements, and reviews existing and proposed systems that currently perform dry fuel transfers. The focus of this paper is on the need for a DTS to enable transfer of bare fuel assemblies. Dry transfer systems for UNF canisters are currently available and in use for transferring loaded canisters between the drying station and storage and transportation casks.

  3. Spray drying for processing of nanomaterials

    International Nuclear Information System (INIS)

    Lindeloev, Jesper Saederup; Wahlberg, Michael

    2009-01-01

    Consolidation of nano-particles into micron-sized granules reduces the potential risks associated with handling nano-powders in dry form. Spray drying is a one step granulation technique which can be designed for safe production of free flowing low dusty granules from suspensions of nano-particles. Spray dried granules are well suited for subsequent processing into final products where the superior properties given by the nano-particles are retained. A spray drier with bag filters inside the drying chamber and recycling of drying gas combined with containment valves are proposed as a safe process for granulation of potential hazardous nano-particles.

  4. Effect of drying conditions on the physical properties of impregnated orange peel

    Directory of Open Access Journals (Sweden)

    K. Manjarres-Pinzon

    2013-09-01

    Full Text Available Orange peel represents approximately 30-40 g/100g of the fresh fruit weight and could be used to develop value-added products. Hence, this study aims to evaluate the effects of drying conditions on the physical properties of orange peel impregnated with sucrose solution. The response surface method (RSM was used to optimize two parameters: drying temperature (35-55 ºC and air flow rate (2-3 m/s. The measured responses used to determine the effect of dying process conditions were: moisture content. drying time. total soluble solids. color and hardness. The dried orange peels from the optimal process were subjected to a sensory test by 60 consumers. The optimum conditions for the drying of orange peels were determined to obtain minimum hardness, moisture content and drying time for a w values below 0.6. The optimum conditions were found to be a dying temperature of 52.3 ºC and air flow rate of 2.0 m/s. At this point, drying time, hardness and moisture content were found to be 20 h, 78.4 N and 7.6%, respectively. The sensory results showed that consumers aged over 30 years old accepted well the dried orange peel.

  5. Drying on the germination and vigor of Crataeva tapia L. seeds

    Directory of Open Access Journals (Sweden)

    Edna Ursulino Alves

    Full Text Available ABSTRACT: Crataeva tapia L. is a fruit native to the Brazilian savanna, the Caatinga, and is used in the production of soft drinks and other beverages. Given the importance of this species and the lack of knowledge about its seeds, this research aimed to evaluate the physiological quality of C. tapia L. seeds subjected to different environments and drying periods. Seeds were dried for the following time periods: 0 (no drying, 24, 48, 72, 96, and 120 hours, in the laboratory environment (25°C and 90% RH and in a greenhouse (30°C and 80% RH. After the drying period, seeds from each of the treatments were used for determining the water content, germination, and vigor (using tests for emergence, first count of germination and emergence, rate of germination and emergence, length, and seedling dry weight. The experimental design was completely randomized and a factorial 2×6 scheme (local environment × drying periods was used with four replicate sets of seeds. The data were subjected to analysis of variance and polynomial regression using quadratic models. The germination and seed vigor reduced as the drying periods increased. For optimum results, the seeds of C. tapia L. must be dried in the laboratory for a period of 48 hours. In addition, their desiccation resistance was classified as intermediate.

  6. Phenolic compounds and vitamins in wild and cultivated apricot (Prunus armeniaca L.) fruits grown in irrigated and dry farming conditions.

    Science.gov (United States)

    Kan, Tuncay; Gundogdu, Muttalip; Ercisli, Sezai; Muradoglu, Ferhad; Celik, Ferit; Gecer, Mustafa Kenan; Kodad, Ossama; Zia-Ul-Haq, Muhammad

    2014-09-23

    Turkey is the main apricot producer in the world and apricots have been produced under both dry and irrigated conditions in the country. In this study, phenolic compounds and vitamins in fruits of one wild (Zerdali) and three main apricot cultivars ('Cataloglu', 'Hacihaliloglu' and 'Kabaasi') grown in both dry and irrigated conditions in Malatya provinces in Turkey were investigated. The findings indicated that higher content of phenolic compounds and vitamins was found in apricot fruits grown in irrigated conditions. Among the cultivars, 'Cataloglu' had the highest rutin contents both in irrigated and dry farming conditions as 2855 μg in irrigated and 6952 μg per 100 g dried weight base in dry conditions and the highest chlorogenic acid content in irrigated and dry farming conditions were measured in fruits of 'Hacıhaliloglu' cultivar as 7542 μg and 15251 μg per 100 g dried weight base. Vitamin C contents in homogenates of fruit flesh and skin was found to be higher than β-caroten, retinol, vitamin E and lycopen contents in apricot fruits both in irrigated and dry farming conditions. The results suggested that apricot fruits grown in both dry and irrigated conditions had high health benefits phytochemicals and phytochemical content varied among cultivars and irrigation conditions as well. However, more detailed biological and pharmacological studies are needed for the demonstration and clarification of health benefits of apricot fruits.

  7. Intracellular water exchange for measuring the dry mass, water mass and changes in chemical composition of living cells.

    Directory of Open Access Journals (Sweden)

    Francisco Feijó Delgado

    Full Text Available We present a method for direct non-optical quantification of dry mass, dry density and water mass of single living cells in suspension. Dry mass and dry density are obtained simultaneously by measuring a cell's buoyant mass sequentially in an H2O-based fluid and a D2O-based fluid. Rapid exchange of intracellular H2O for D2O renders the cell's water content neutrally buoyant in both measurements, and thus the paired measurements yield the mass and density of the cell's dry material alone. Utilizing this same property of rapid water exchange, we also demonstrate the quantification of intracellular water mass. In a population of E. coli, we paired these measurements to estimate the percent dry weight by mass and volume. We then focused on cellular dry density - the average density of all cellular biomolecules, weighted by their relative abundances. Given that densities vary across biomolecule types (RNA, DNA, protein, we investigated whether we could detect changes in biomolecular composition in bacteria, fungi, and mammalian cells. In E. coli, and S. cerevisiae, dry density increases from stationary to exponential phase, consistent with previously known increases in the RNA/protein ratio from up-regulated ribosome production. For mammalian cells, changes in growth conditions cause substantial shifts in dry density, suggesting concurrent changes in the protein, nucleic acid and lipid content of the cell.

  8. Phenolic compounds and vitamins in wild and cultivated apricot (Prunus armeniaca L. fruits grown in irrigated and dry farming conditions

    Directory of Open Access Journals (Sweden)

    Tuncay Kan

    2014-01-01

    Full Text Available BACKGROUND: Turkey is the main apricot producer in the world and apricots have been produced under both dry and irrigated conditions in the country. In this study, phenolic compounds and vitamins in fruits of one wild (Zerdali and three main apricot cultivars ('Cataloglu', 'Hacihaliloglu' and 'Kabaasi' grown in both dry and irrigated conditions in Malatya provinces in Turkey were investigated. RESULTS: The findings indicated that higher content of phenolic compounds and vitamins was found in apricot fruits grown in irrigated conditions. Among the cultivars, 'Cataloglu' had the highest rutin contents both in irrigated and dry farming conditions as 2855 µg in irrigated and 6952 µg per 100 g dried weight base in dry conditions and the highest chlorogenic acid content in irrigated and dry farming conditions were measured in fruits of 'Hacıhaliloglu' cultivar as 7542 µg and 15251 µg per 100 g dried weight base. Vitamin C contents in homogenates of fruit flesh and skin was found to be higher than β-caroten, retinol, vitamin E and lycopen contents in apricot fruits both in irrigated and dry farming conditions. CONCLUSION: The results suggested that apricot fruits grown in both dry and irrigated conditions had high health benefits phytochemicals and phytochemical content varied among cultivars and irrigation conditions as well. However, more detailed biological and pharmacological studies are needed for the demonstration and clarification of health benefits of apricot fruits.

  9. Intracellular Water Exchange for Measuring the Dry Mass, Water Mass and Changes in Chemical Composition of Living Cells

    Science.gov (United States)

    Hecht, Vivian C.; Son, Sungmin; Li, Yingzhong; Knudsen, Scott M.; Olcum, Selim; Higgins, John M.; Chen, Jianzhu; Grover, William H.; Manalis, Scott R.

    2013-01-01

    We present a method for direct non-optical quantification of dry mass, dry density and water mass of single living cells in suspension. Dry mass and dry density are obtained simultaneously by measuring a cell’s buoyant mass sequentially in an H2O-based fluid and a D2O-based fluid. Rapid exchange of intracellular H2O for D2O renders the cell’s water content neutrally buoyant in both measurements, and thus the paired measurements yield the mass and density of the cell’s dry material alone. Utilizing this same property of rapid water exchange, we also demonstrate the quantification of intracellular water mass. In a population of E. coli, we paired these measurements to estimate the percent dry weight by mass and volume. We then focused on cellular dry density – the average density of all cellular biomolecules, weighted by their relative abundances. Given that densities vary across biomolecule types (RNA, DNA, protein), we investigated whether we could detect changes in biomolecular composition in bacteria, fungi, and mammalian cells. In E. coli, and S. cerevisiae, dry density increases from stationary to exponential phase, consistent with previously known increases in the RNA/protein ratio from up-regulated ribosome production. For mammalian cells, changes in growth conditions cause substantial shifts in dry density, suggesting concurrent changes in the protein, nucleic acid and lipid content of the cell. PMID:23844039

  10. Electrical, Structural and Mechanical Properties of Superconducting MGB2/MG Composites

    International Nuclear Information System (INIS)

    Ulucan, S.

    2004-01-01

    The brittle nature of MgB 2 does not allow this material to be used as a stand-alone material for large scale applications based on wire production. MgB 2 /Mg composites were prepared using metal matrix composite fabrication technique. To obtain composites MgB 2 and Mg powders were mixed at different weight fractions and uniaxially pressed in a cylindrical dye under the pressure of 0.5 GPa and 1.0 GPa for two hours at various temperatures. XRD, SEM and EDX techniques were used for phase identification and microstructural studies. Resistivities of the composites were measured between 20 K and room temperature. The effect of temperature on the mechanical properties of MgB 2 /Mg composites was investigated. For this purpose, compressive mechanical testing was performed to measure elastic modulus and strain at failure values of the composites. It was found that the relative weight fraction of the powders and the temperature have same considerable effect on the electrical, microstructural and the mechanical properties of the composites

  11. Superconductivity in MgB{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Muranaka, Takahiro; Akimitsu, Jun [Aoyama Gakuin Univ., Kanagawa (Japan). Dept. of Physics and Mathematics

    2011-07-01

    We review superconductivity in MgB{sub 2} in terms of crystal and electronic structure, electron-phonon coupling, two-gap superconductivity and application. Finally, we introduce the development of new superconducting materials in related compounds. (orig.)

  12. Additive Manufacturing of Magnesium (Mg) Alloys

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed work is to investigate additive manufacturing techniques for Mg alloys.  It will leverage off research being conducted at University of Florida and...

  13. Atmospheric freeze drying assisted by power ultrasound

    International Nuclear Information System (INIS)

    Santacatalina, J V; Cárcel, J A; Garcia-Perez, J V; Mulet, A; Simal, S

    2012-01-01

    Atmospheric freeze drying (AFD) is considered an alternative to vacuum freeze drying to keep the quality of fresh product. AFD allows continuous drying reducing fix and operating costs, but presents, as main disadvantage, a long drying time required. The application of power ultrasound (US) can accelerate AFD process. The main objective of the present study was to evaluate the application of power ultrasound to improve atmospheric freeze drying of carrot. For that purpose, AFD experiments were carried out with carrot cubes (10 mm side) at constant air velocity (2 ms −1 ), temperature (−10°C) and relative humidity (10%) with (20.5 kWm −3 ,USAFD) and without (AFD) ultrasonic application. A diffusion model was used in order to quantify the influence of US in drying kinetics. To evaluate the quality of dry products, rehydration capacity and textural properties were determined. The US application during AFD of carrot involved the increase of drying rate. The effective moisture diffusivity identified in USAFD was 73% higher than in AFD experiments. On the other hand, the rehydration capacity was higher in USAFD than in AFD and the hardness of dried samples did not show significant (p<0.05) differences. Therefore, US application during AFD significantly (p<0.05) sped-up the drying process preserving the quality properties of the dry product.

  14. Lightweight MgB2 superconducting 10 MW wind generator

    Science.gov (United States)

    Marino, I.; Pujana, A.; Sarmiento, G.; Sanz, S.; Merino, J. M.; Tropeano, M.; Sun, J.; Canosa, T.

    2016-02-01

    The offshore wind market demands a higher power rate and more reliable turbines in order to optimize capital and operational costs. The state-of-the-art shows that both geared and direct-drive conventional generators are difficult to scale up to 10 MW and beyond due to their huge size and weight. Superconducting direct-drive wind generators are considered a promising solution to achieve lighter weight machines. This work presents an innovative 10 MW 8.1 rpm direct-drive partial superconducting generator using MgB2 wire for the field coils. It has a warm iron rotor configuration with the superconducting coils working at 20 K while the rotor core and the armature are at ambient temperature. A cooling system based on cryocoolers installed in the rotor extracts the heat from the superconducting coils by conduction. The generator's main parameters are compared against a permanent magnet reference machine, showing a significant weight and size reduction. The 10 MW superconducting generator concept will be experimentally validated with a small-scale magnetic machine, which has innovative components such as superconducting coils, modular cryostats and cooling systems, and will have similar size and characteristics as the 10 MW generator.

  15. Lightweight MgB2 superconducting 10 MW wind generator

    International Nuclear Information System (INIS)

    Marino, I; Pujana, A; Sarmiento, G; Sanz, S; Merino, J M; Tropeano, M; Sun, J; Canosa, T

    2016-01-01

    The offshore wind market demands a higher power rate and more reliable turbines in order to optimize capital and operational costs. The state-of-the-art shows that both geared and direct-drive conventional generators are difficult to scale up to 10 MW and beyond due to their huge size and weight. Superconducting direct-drive wind generators are considered a promising solution to achieve lighter weight machines. This work presents an innovative 10 MW 8.1 rpm direct-drive partial superconducting generator using MgB 2 wire for the field coils. It has a warm iron rotor configuration with the superconducting coils working at 20 K while the rotor core and the armature are at ambient temperature. A cooling system based on cryocoolers installed in the rotor extracts the heat from the superconducting coils by conduction. The generator’s main parameters are compared against a permanent magnet reference machine, showing a significant weight and size reduction. The 10 MW superconducting generator concept will be experimentally validated with a small-scale magnetic machine, which has innovative components such as superconducting coils, modular cryostats and cooling systems, and will have similar size and characteristics as the 10 MW generator. (paper)

  16. Technique of solar drying the linden

    International Nuclear Information System (INIS)

    Fonseca Fonseca, Susana; Andión Torres, Ronald; Espinosa Borges, Ruberlando; Torres Ten, Alonso; Arzuaga Machado, Yusnel; Fuentes lombá, Osmay

    2017-01-01

    In Santiago of Cuba exists interest in the utilization of medicinal plants for the manufacture of flowed abstract and Tinturas, and this requires the dry product. At the present time this process is done in houses roofed. This product will be dried at 10 or 12 days. Having in account than in the Center of investigation of Solar Energy was developed a prototype of solar drier, which enables the drying of the anamu with the required quality, in this work is done a study, for the utilization of the aforementioned drier, for the drying of others medicinal plants. It is determine and evaluated experimentally a Procedure of drying of linden in this solar drier. The dry plants were sent to the UBPC La Rosita of medicinal plants, which manifested conformity with the obtained results, showing contentment with the quality of the dry product. (author)

  17. Dry well storage of spent LWBR fuel

    International Nuclear Information System (INIS)

    Christensen, A.B.; Fielding, K.D.

    1985-01-01

    Recently, 50 dry wells were constructed at the Idaho Chemical Processing Plant (ICPP) to temporarily store the Light Water Breeder Reactor (LWBR) fuel. Over 400 dry wells of the same design are projected to be constructed in the next 5 yr at the ICPP to store unreprocessible fuels until a permanent repository becomes available. This summary describes the LWBR fuel storage dry wells and the enhancements made over the Peach Bottom fuel and Fermi blanket dry wells that have been in use for up to 4 yr. Dry well storage at the ICPP has historically been found to be a safe and efficient method of temporary fuel storage. The LWBR dry wells should be more reliable than the original dry wells and provide data not previously available

  18. Impregnation of leather during "freeze-drying"

    DEFF Research Database (Denmark)

    Storch, Mikkel; Vestergaard Poulsen Sommer, Dorte; Hovmand, Ida

    2016-01-01

    Freeze-drying is a recognized method for the preservation of waterlogged objects. Naturally, freeze-drying has also been used for waterlogged archaeological leather often after treatment with Na2.EDTA and impregnation with PEG; but the treated leather sometimes suffers from “excessive drying......” becoming too stiff and brittle. The aim of this study was to examine the effect of a conventional freeze-drying method against an alternative freeze-drying method that preserves the natural moisture content of the leather. Both new and archaeological waterlogged leather were included in the study...... suggest that the process which takes place within the leather during the freeze-drying in not actual freeze-drying, but rather a sophisticated way of distributing the impregnating agent. The pure ice phase freezes out, but the impregnating agent remains liquid as the temperature does not become low enough...

  19. Dry shrinkage characteristics of buffer materials

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H. [ITC, Tokai, Ibaraki (Japan); Fujita, A.

    1999-03-01

    Generation of cracks due to drying of compressed bentonite was observed by changing the initial water content to obtain shrinkage constants such as shrinkage limit and shrinking rate. As a result, generation of practically no cracks was observed when the initial water content of samples was below 13%. The volume change due to drying increased with the water content in the sample, and the shrinkage constants were found to depend on the initial water content. Further, the one-dimensional compression strength after drying was compared with that before drying in order to clarify the effect of cracks generated by drying on the mechanical strength. As a result, the dry sample with cracks proved to have large one-dimensional compression strength or E{sub 50} compared to wet samples, so that the mechanical strength was kept even after drying. (H. Baba)

  20. Properties of thymidylate synthetase from Ehrlich ascites carcinoma cells. Effect of Mg2/ and MgATP2-.

    Science.gov (United States)

    Jastreboff, M; Kedzierska, B; Rode, W

    1982-01-15

    Ehrlich ascites carcinoma thymidylate synthetase was purified to electrophoretic homogeneity by affinity chromatography on 10-formyl-5,8-dideazofolate-ethyl-Sepharose. Electrophoretic analysis of the formation of the enzyme-5-fluorodeoxyuridylate-5,10-methylenetetrahydrofolate complexes showed the presence of two binding sites for 5-fluorodeoxyuridylate on the enzyme molecule. Molecular weight of the native enzyme was found to be 78,5000, whereas that of its monomer was 38, 500. The apparent Michaelis constants for dUMP and (+/-)-L-5,10-methylenetetrahydrofolate were 1.3 +/- 0.4 and 32.2 +/- 0.7 micrometers respectively. Phosphate acted as a weak inhibitor, competitive toward dUMP. The enzyme reaction exhibited a temperature-dependent change of activation energy, reflected in the binding affinity of dUMP, with a transitional temperature of 35.8 degrees. Both Mg2+ and MgATP2- were strong activators of the enzyme, MgATP2- being more effective.