ASM observations of X-ray flares from 4U 0115+63 and ASM 1354-64.

Science.gov (United States)

Tsunemi, H.; Kitamoto, S.

The authors report two X-ray flares detected with the All Sky Monitor (ASM) on board the GINGA satellite. One is from the recurrent X-ray pulsar 4U 0115+63 and the other is from the probable recurrent X-ray nova named ASM 1354-64. The maximum intensity for 4U 0115+63 was 180 mCrab and its duration was at least 22 days. Its spectrum was hard and resembled those of X-ray pulsars. The maximum intensity of ASM 1354-64 was 300 mCrab. It faded down below the detection limit at the end of August 1987. Its spectrum was soft and was similar to those of black hole candidates.

Robust boundary detection of left ventricles on ultrasound images using ASM-level set method.

Science.gov (United States)

Zhang, Yaonan; Gao, Yuan; Li, Hong; Teng, Yueyang; Kang, Yan

2015-01-01

Level set method has been widely used in medical image analysis, but it has difficulties when being used in the segmentation of left ventricular (LV) boundaries on echocardiography images because the boundaries are not very distinguish, and the signal-to-noise ratio of echocardiography images is not very high. In this paper, we introduce the Active Shape Model (ASM) into the traditional level set method to enforce shape constraints. It improves the accuracy of boundary detection and makes the evolution more efficient. The experiments conducted on the real cardiac ultrasound image sequences show a positive and promising result.

Rethinking ASME III seismic analysis for piping operability evaluations

International Nuclear Information System (INIS)

Adams, T.M.; Stevenson, J.D.

1994-01-01

It has been recognized since the mid 1980's that there are very large seismic margins to failure for nuclear piping systems when designed using current industry practice, design criteria, and methods. As a result of this realization there are or have been approximately eighteen initiatives within the ASME , Boiler and Pressure Vessel Code Section III, Division 1, in the form of proposed code cases and proposed code text changes designed to reduce these failure margins to more realistic values. For the most part these initiatives have concentrated on reclassifying seismic inertia stresses in the piping as secondary and increasing the allowable stress limits permitted by Section III of the ASME, Boiler Code. This paper focuses on the application of non-linear spectral analysis methods as a method to reduce the input seismic demand determination and thereby reduce the seismic failure margins. The approach is evaluated using the ASME Boiler Pressure Vessel Code Section III Subgroup on Design benchmark procedure as proposed by the Subgroup's Special Task Group on Integrated Piping Criteria. Using this procedure, criteria are compared to current code criterion and analysis methods, and several other of the currently proposed Boiler and Pressure Vessel, Section III, changes. Finally, the applicability of the non-linear spectral analysis to continued Safe Operation Evaluations is reviewed and discussed

Evaluation of ASME code flaw analysis procedure using the influence function method for application to PWR primary piping

International Nuclear Information System (INIS)

Hong, S.Y.; Yeater, M.L.

1985-01-01

This paper discusses stress intensity factor calculations and fatigue analysis for a PWR primary coolant piping system. The influence function method is applied to evaluate ASME Code Section XI Appendix A ''analysis of flaw indication'' for the application to a PWR primary piping. Results of the analysis are discussed in detail. (orig.)

The ASME research task force on risk-based in-service inspection

International Nuclear Information System (INIS)

Balkey, K.R.; Chapman, O.J.V.

1997-01-01

The use of risk-based methods in the development of in-service inspection (ISI) and in-service testing (IST) programs for nuclear power plant and other industrial applications has been studied for the last several years through the American Society of Mechanical Engineers Centre for Research and Technology Development (ASME 1991, 1992, 1994, 1996). The results of this work are being used as a foundation to develop specific requirements for implementation of risk-based technology in ASME Codes and Standards, regulatory requirements and industry programs both in the U.S. and other countries. This paper provides a brief overview of the ASME Research Methodology and how it has been adapted for application to the inspection of piping within the USA. It also relates how the reliability of nondestructive examination (NDE) methods for pressure boundary components can impact the risk and discusses the relationship between this and NDE qualification/demonstration now being implemented in Europe and the USA. (orig.)

Activated sludge model No. 2d, ASM2d

DEFF Research Database (Denmark)

Henze, M.

1999-01-01

The Activated Sludge Model No. 2d (ASM2d) presents a model for biological phosphorus removal with simultaneous nitrification-denitrification in activated sludge systems. ASM2d is based on ASM2 and is expanded to include the denitrifying activity of the phosphorus accumulating organisms (PAOs......). This extension of ASM2 allows for improved modeling of the processes, especially with respect to the dynamics of nitrate and phosphate. (C) 1999 IAWQ Published by Elsevier Science Ltd. All rights reserved....

An example of a component replacement when applying ASME N509 and ASME N510 to older ventilation systems

International Nuclear Information System (INIS)

Arndt, T.E.

1994-06-01

This paper presents an example of a component replacement (electric heater) when installed in an older ventilation system that was constructed before the issuance of ASME N509 and N510. Many of the existing ventilation systems at the Hanford Site were designed, fabricated, and installed before the issuance of ASME N509 and N510. Requiring the application of these codes to existing ventilation systems presents challenges to the engineer when design changes are needed. Although it may seem that the application of ASME N509 or N510 may be a hindrance at times, this does not need to occur. Proper preparation at the start of project or design modifications can minimize frustration to the engineer when it is judged that portions of ASME N509 and N510 do not apply in a particular application

Safety Analysis Report for the KRI-ASM Transport Package

Energy Technology Data Exchange (ETDEWEB)

Bang, K. S.; Lee, J. C.; Kim, D. H.; Park, H. Y.; Kim, J. B.; Kim, H. J.; Seo, K. S

2005-11-15

Safety evaluation for the KRI-ASM transport package to transport safely I-131, which is produced at HANARO research reactor in KAERI, was carried out. In the safety analyses results for the KRI-ASM transport package, all the maximum stresses as well as the maximum temperature of the surface are lower than their allowable limits. The safety tests were performed by using the test model of the KRI-ASM transport package. Leak Test was performed after drop test and penetration test, the measured leakage rate was lower than allowable leakage rate. It is revealed that the containment integrity of the KRI-ASM transport package is maintained. Therefore, it shows that the integrity of the KRI-ASM transport package is well maintained.

ASME Code requirements for multi-canister overpack design and fabrication

International Nuclear Information System (INIS)

SMITH, K.E.

1998-01-01

The baseline requirements for the design and fabrication of the MCO include the application of the technical requirements of the ASME Code, Section III, Subsection NB for containment and Section III, Subsection NG for criticality control. ASME Code administrative requirements, which have not historically been applied at the Hanford site and which have not been required by the US Nuclear Regulatory Commission (NRC) for licensed spent fuel casks/canisters, were not invoked for the MCO. As a result of recommendations made from an ASME Code consultant in response to DNFSB staff concerns regarding ASME Code application, the SNF Project will be making the following modifications: issue an ASME Code Design Specification and Design Report, certified by a Registered Professional Engineer; Require the MCO fabricator to hold ASME Section III or Section VIII, Division 2 accreditation; and Use ASME Authorized Inspectors for MCO fabrication. Incorporation of these modifications will ensure that the MCO is designed and fabricated in accordance with the ASME Code. Code Stamping has not been a requirement at the Hanford site, nor for NRC licensed spent fuel casks/canisters, but will be considered if determined to be economically justified

International Accreditation of ASME Codes and Standards

International Nuclear Information System (INIS)

Green, Mervin R.

1989-01-01

ASME established a Boiler Code Committee to develop rules for the design, fabrication and inspection of boilers. This year we recognize 75 years of that Code and will publish a history of that 75 years. The first Code and subsequent editions provided for a Code Symbol Stamp or mark which could be affixed by a manufacturer to a newly constructed product to certify that the manufacturer had designed, fabricated and had inspected it in accordance with Code requirements. The purpose of the ASME Mark is to identify those boilers that meet ASME Boiler and Pressure Vessel Code requirements. Through thousands of updates over the years, the Code has been revised to reflect technological advances and changing safety needs. Its scope has been broadened from boilers to include pressure vessels, nuclear components and systems. Proposed revisions to the Code are published for public review and comment four times per year and revisions and interpretations are published annually; it's a living and constantly evolving Code. You and your organizations are a vital part of the feedback system that keeps the Code alive. Because of this dynamic Code, we no longer have columns in newspapers listing boiler explosions. Nevertheless, it has been argued recently that ASME should go further in internationalizing its Code. Specifically, representatives of several countries, have suggested that ASME delegate to them responsibility for Code implementation within their national boundaries. The question is, thus, posed: Has the time come to franchise responsibility for administration of ASME's Code accreditation programs to foreign entities or, perhaps, 'institutes.' And if so, how should this be accomplished?

Proceedings: 2001 ASME/EPRI Radwaste Workshop

International Nuclear Information System (INIS)

2001-01-01

Nuclear utilities continually evaluate methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has increased the emphasis on this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technology and management improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

Temporal Deductive Verification of Basic ASM Models

OpenAIRE

Daho, Hocine El-Habib; University of Oran; Benhamamouch, Djillali; University of Oran

2010-01-01

Abstract State Machines (ASMs, for short) provide a practical new computational model which has been applied in the area of software engineering for systems design and analysis. However, reasoning about ASM models occurs, not within a formal deductive system, but basically in the classical informal proofs style of mathematics. Several formal verification approaches for proving correctness of ASM models have been investigated. In this paper we consider the use of the TLA+logic for the deductive...

Meeting the difficulties of an ASME calibration for pipe welds

Energy Technology Data Exchange (ETDEWEB)

Ginzel, E., E-mail: eginzel@mri.on.ca [Materials Research Inst., Waterloo, Ontario (Canada); Ginzel, R.; Buchholz, J., E-mail: rginzel@eclipsescientific.com [Eclipse Scientific, Waterloo, Ontario (Canada)

2013-11-15

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code Section V deals with Non-Destructive Testing (NDT). In North America the use of ASME Sec. V is not always limited to just ASME regulated projects. Even such seemingly unrelated Standards as CSA Z662 (the Canadian construction standard for Oil and Gas Pipeline Systems) references this document for some aspects of the NDT. ASME has several codes that are dedicated to piping welds, for example ASME 31.1, 31.3 and 31.8. All of them reference back to ASME Section V Article 4 for the accepted techniques to use when UT is the examination option, but sometimes ASME is not very helpful. As they try to leave options open in one area they close the doors in others, or so it seems when reading the clauses as mandatory where you see the word 'shall'. This paper will attempt to layout the issues with pipe weld inspections as per Article 4, 2011 edition. Like all other codes and standards, ASME is a regulated standard that is regularly reviewed and updated, and one must be careful to reference the year of the edition being used. For the purposes of this paper we have used the 2010/11 edition. (author)

Meeting the difficulties of an ASME calibration for pipe welds

International Nuclear Information System (INIS)

Ginzel, E.; Ginzel, R.; Buchholz, J.

2013-01-01

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code Section V deals with Non-Destructive Testing (NDT). In North America the use of ASME Sec. V is not always limited to just ASME regulated projects. Even such seemingly unrelated Standards as CSA Z662 (the Canadian construction standard for Oil and Gas Pipeline Systems) references this document for some aspects of the NDT. ASME has several codes that are dedicated to piping welds, for example ASME 31.1, 31.3 and 31.8. All of them reference back to ASME Section V Article 4 for the accepted techniques to use when UT is the examination option, but sometimes ASME is not very helpful. As they try to leave options open in one area they close the doors in others, or so it seems when reading the clauses as mandatory where you see the word 'shall'. This paper will attempt to layout the issues with pipe weld inspections as per Article 4, 2011 edition. Like all other codes and standards, ASME is a regulated standard that is regularly reviewed and updated, and one must be careful to reference the year of the edition being used. For the purposes of this paper we have used the 2010/11 edition. (author)

An example of a component replacement when applying ASME N509 and ASME N510 to older ventilation systems

Energy Technology Data Exchange (ETDEWEB)

Arndt, T.E. [Westinghouse Hanford Company, Richland, WA (United States)

1995-02-01

This paper presents an example of a component replacement (electric heater) when installed in an older ventilation system that was constructed before the issuance of ASME N509{sup 1} and N510{sup 2}. Many of the existing ventilation systems at the Hanford Site were designed, fabricated, and installed before the issuance of ASME N509{sup 1} and N510{sup 2}. Requiring the application of these codes to existing ventilation systems presents challenges to the engineer when design changes are needed. Although it may seem that the application of ASME N509{sup 1} or N510{sup 2} may be a hindrance at times, this does not need to occur. Proper preparation at the start of project or design modifications can minimize frustration to the engineer when it is judged that portions of ASME N509{sup 1} and N510{sup 2} do not apply in a particular application.

Proceedings: 2000 ASME/EPRI Radwaste Workshop

International Nuclear Information System (INIS)

2001-01-01

Nuclear utilities are continually evaluating methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has added increased emphasis to this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technological and managerial improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

Review of ASME-NH Design Materials for Creep-Fatigue

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Kim, Jong Bum

2010-01-01

To review and recommend the candidate design materials for the Sodium-Cooled Fast Reactor, the material sensitivity evaluations by the comparison of design data between the ASME-NH materials were performed by using the SIE ASME-NH computer program implementing the material database of the ASME-NH. The design material data provided by the ASME-NH code are the elastic modulus and yield Strength, Time-Independent Allowable Stress Intensity value, time-dependent allowable stress intensity value, expected minimum stress-to rupture value, stress rupture Factors for weldment, isochronous stress-strain curves, and design fatigue curves. Among these, the data related with the creep-fatigue evaluation are investigated in this study

Cisco ASM Router

CERN Multimedia

2001-01-01

One of the two "ASM/2-32EM" boxes installed in 1988, from "Cisco Systems Inc." - then an unknown 20-employee company in Menlo Park, California (USA). This is one of the first two Cisco boxes to appear in Switzerland, and possibly Europe. The 220v power supply was a special modification made for use at CERN. They supported IP address filtering, which seemed just what CERN needed to help protect the new Cray XMP-48 super computer from network hackers. The two ASM boxes were both routers and terminal servers. They protected a secure private Ethernet segment used by the Cray project, as well as providing secure terminal connections to that segment, including CERN's first dialback terminal service, which allowed Cray and CERN system analysts to work on the machine from home, using another Cisco feature called TACACS. (Kindly offered by B. Segal who discovered this company while at a Usenix Conference in Phoenix, Arizona in June 1987.)

Report on the Current Technical Issues on ASME Nuclear Code and Standard

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2008-11-01

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

[Cardiac Synchronization Function Estimation Based on ASM Level Set Segmentation Method].

Science.gov (United States)

Zhang, Yaonan; Gao, Yuan; Tang, Liang; He, Ying; Zhang, Huie

At present, there is no accurate and quantitative methods for the determination of cardiac mechanical synchronism, and quantitative determination of the synchronization function of the four cardiac cavities with medical images has a great clinical value. This paper uses the whole heart ultrasound image sequence, and segments the left & right atriums and left & right ventricles of each frame. After the segmentation, the number of pixels in each cavity and in each frame is recorded, and the areas of the four cavities of the image sequence are therefore obtained. The area change curves of the four cavities are further extracted, and the synchronous information of the four cavities is obtained. Because of the low SNR of Ultrasound images, the boundary lines of cardiac cavities are vague, so the extraction of cardiac contours is still a challenging problem. Therefore, the ASM model information is added to the traditional level set method to force the curve evolution process. According to the experimental results, the improved method improves the accuracy of the segmentation. Furthermore, based on the ventricular segmentation, the right and left ventricular systolic functions are evaluated, mainly according to the area changes. The synchronization of the four cavities of the heart is estimated based on the area changes and the volume changes.

Regulation of dynein-mediated autophagosomes trafficking by ASM in CASMCs.

Science.gov (United States)

Xu, Ming; Zhang, Qiufang; Li, Pin-Lan; Nguyen, Thaison; Li, Xiang; Zhang, Yang

2016-01-01

Acid sphingomyelinase (ASM; gene symbol Smpd1) has been shown to play a crucial role in autophagy maturation by controlling lysosomal fusion with autophagosomes in coronary arterial smooth muscle cells (CASMCs). However, the underlying molecular mechanism by which ASM controls autophagolysosomal fusion remains unknown. In primary cultured CASMCs, lysosomal Ca2+ induced by 7-ketocholesterol (7-Ket, an atherogenic stimulus and autophagy inducer) was markedly attenuated by ASM deficiency or TRPML1 gene silencing suggesting that ASM signaling is required for TRPML1 channel activity and subsequent lysosomal Ca(2+) release. In these CASMCs, ASM deficiency or TRPML1 gene silencing markedly inhibited 7-Ket-induced dynein activation. In addition, 7-Ket-induced autophagosome trafficking, an event associated with lysosomal Ca(2+) release and dynein activity, was significantly inhibited in ASM-deficient (Smpd1(-/-)) CASMCs compared to that in Smpd1(+/+) CASMCs. Finally, overexpression of TRPML1 proteins restored 7-Ket-induced lysosomal Ca(2+) release and autophagosome trafficking in Smpd1-/- CASMCs. Collectively, these results suggest that ASM plays a critical role in regulating lysosomal TRPML1-Ca(2+) signaling and subsequent dynein-mediated autophagosome trafficking, which leads its role in controlling autophagy maturation in CASMCs under atherogenic stimulation.

ASME nuclear codes and standards risk management strategic planning

International Nuclear Information System (INIS)

Hill, Ralph S. III; Balkey, Kenneth R.; Erler, Bryan A.; Wesley Rowley, C.

2007-01-01

This paper is prepared in honor and in memory of the late Professor Emeritus Yasuhide Asada to recognize his contributions to ASME Nuclear Codes and Standards initiatives, particularly those related to risk-informed technology and System Based Code developments. For nearly two decades, numerous risk-informed initiatives have been completed or are under development within the ASME Nuclear Codes and Standards organization. In order to properly manage the numerous initiatives currently underway or planned for the future, the ASME Board on Nuclear Codes and Standards (BNCS) has an established Risk Management Strategic Plan (Plan) that is maintained and updated by the ASME BNCS Risk Management Task Group. This paper presents the latest approved version of the plan beginning with a background of applications completed to date, including the recent probabilistic risk assessment (PRA) standards developments for nuclear power plant applications. The paper discusses planned applications within ASME Nuclear Codes and Standards that will require expansion of the ASME PRA Standard to support new advanced light water reactor and next generation reactor developments, such as for high temperature gas-cooled reactors. Emerging regulatory developments related to risk-informed, performance- based approaches are summarized. A long-term vision for the potential development and evolution to a nuclear systems code that adopts a risk-informed approach across a facility life-cycle (design, construction, operation, maintenance, and closure) is also summarized. Finally, near term and long term actions are defined across the ASME Nuclear Codes and Standards organizations related to risk management, including related U.S. regulatory activities. (author)

Design Procedure of Graphite Components by ASME HTR Codes

Energy Technology Data Exchange (ETDEWEB)

Kang, Ji-Ho; Jo, Chang Keun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study, the ASME B and PV Code, Subsection HH, Subpart A, design procedure for graphite components of HTRs was reviewed and the differences from metal materials were remarked. The Korean VHTR has a prismatic core which is made of multiple graphite blocks, reflectors, and core supports. One of the design issues is the assessment of the structural integrity of the graphite components because the graphite is brittle and shows quite different behaviors from metals in high temperature environment. The American Society of Mechanical Engineers (ASME) issued the latest edition of the code for the high temperature reactors (HTR) in 2015. In this study, the ASME B and PV Code, Subsection HH, Subpart A, Graphite Materials was reviewed and the special features were remarked. Due the brittleness of graphites, the damage-tolerant design procedures different from the conventional metals were adopted based on semi-probabilistic approaches. The unique additional classification, SRC, is allotted to the graphite components and the full 3-D FEM or equivalent stress analysis method is required. In specific conditions, the oxidation and viscoelasticity analysis of material are required. The fatigue damage rule has not been established yet.

Design Procedure of Graphite Components by ASME HTR Codes

International Nuclear Information System (INIS)

Kang, Ji-Ho; Jo, Chang Keun

2016-01-01

In this study, the ASME B and PV Code, Subsection HH, Subpart A, design procedure for graphite components of HTRs was reviewed and the differences from metal materials were remarked. The Korean VHTR has a prismatic core which is made of multiple graphite blocks, reflectors, and core supports. One of the design issues is the assessment of the structural integrity of the graphite components because the graphite is brittle and shows quite different behaviors from metals in high temperature environment. The American Society of Mechanical Engineers (ASME) issued the latest edition of the code for the high temperature reactors (HTR) in 2015. In this study, the ASME B and PV Code, Subsection HH, Subpart A, Graphite Materials was reviewed and the special features were remarked. Due the brittleness of graphites, the damage-tolerant design procedures different from the conventional metals were adopted based on semi-probabilistic approaches. The unique additional classification, SRC, is allotted to the graphite components and the full 3-D FEM or equivalent stress analysis method is required. In specific conditions, the oxidation and viscoelasticity analysis of material are required. The fatigue damage rule has not been established yet

AsmL Specification of a Ptolemy II Scheduler

DEFF Research Database (Denmark)

Lázaro Cuadrado, Daniel; Koch, Peter; Ravn, Anders Peter

2003-01-01

Ptolemy II is a tool that combines different computational models for simulation and design of embedded systems. AsmL is a software specification language based on the Abstract State Machine formalism. This paper reports on development of an AsmL model of the Synchronous Dataflow domain scheduler...

High temperature structural integrity evaluation method and application studies by ASME-NH for the next generation reactor design

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, Jae Han

2006-01-01

The main purpose of this paper is to establish the high temperature structural integrity evaluating procedures for the next generation reactors, which are to be operated at over 500 .deg. C and for 60 years. To do this, comparison studies of the high temperature structural design codes and assessment procedures such as the ASME-NH (USA), RCC-MR (France), DDS (Japan), and R5 (UK) are carried out in view of the accumulated inelastic strain and the creep-fatigue damage evaluations. Also the application procedures of the ASME-NH rules with the actual thermal and structural analysis results are described in detail. To overcome the complexity and the engineering costs arising from a real application of the ASME-NH rules by hand, all the procedures established in this study such as the time-dependent primary stress limits, total accumulated creep ratcheting strain limits, and the creep-fatigue damage limits are computerized and implemented into the SIE ASME-NH program. Using this program, the selected high temperature structures subjected to two cycle types are evaluated and the parametric studies for the effects of the time step size, primary load, number of cycles, normal temperature for the creep damage evaluations and the effects of the load history on the creep ratcheting strain calculations are investigated

Researching on knowledge architecture of design by analysis based on ASME code

International Nuclear Information System (INIS)

Bao Shiyi; Zhou Yu; He Shuyan

2003-01-01

The quality of knowledge-based system's knowledge architecture is one of decisive factors of knowledge-based system's validity and rationality. For designing the ASME code knowledge based system, this paper presents a knowledge acquisition method which is extracting knowledge through document analysis consulted domain experts' knowledge. Then the paper describes knowledge architecture of design by analysis based on the related rules in ASME code. The knowledge of the knowledge architecture is divided into two categories: one is empirical knowledge, and another is ASME code knowledge. Applied as the basement of the knowledge architecture, a general procedural process of design by analysis that is met the engineering design requirements and designers' conventional mode is generalized and explained detailed in the paper. For the sake of improving inference efficiency and concurrent computation of KBS, a kind of knowledge Petri net (KPN) model is proposed and adopted in expressing the knowledge architecture. Furthermore, for validating and verifying of the empirical rules, five knowledge validation and verification theorems are given in the paper. Moreover the research production is applicable to design the knowledge architecture of ASME codes or other engineering standards. (author)

A user's perspective on the merits and shortcomings of ASME Section III

International Nuclear Information System (INIS)

Antaki, G.A.

1994-01-01

There are several aspects of Section III which when compared to process industry codes (ASME VIII, ASME B31.3, API, etc.) have proven to be a significant improvement in engineering practice. There are, however, other aspects of ASME III which have added to costs without clear benefits in safety or reliability. The authors present a user's perspective on some of the relative merits and shortcomings of the nuclear codes (ASME III and XI) compared to the process industry codes (such as ASME VIII, B31.3 and API)

Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

Energy Technology Data Exchange (ETDEWEB)

Seniuk, P.J.

1996-12-01

This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, {open_quotes}Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plants{close_quotes}. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O&M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O&M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion.

Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

International Nuclear Information System (INIS)

Seniuk, P.J.

1996-01-01

This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, open-quotes Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plantsclose quotes. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O ampersand M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O ampersand M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion

Application procedures and analysis examples of the SIE ASME-NH program

International Nuclear Information System (INIS)

Kim, Seok Hoon; Koo, G. H.; Kim, J. B.

2010-12-01

In this report, the design rule of the ASME-NH Code was briefly summarized and the application procedures of SIE ASME-NH program were analysed, the analysis examples were described. The SIE ASME-NH program was developed according to the ASME Code Section III Subsection NH rules to perform the primary stress limits, the accumulated inelastic strain limits and the creep fatigue damage evaluations in the structural design of nuclear power plants operating with high temperatures over creep temperature at normal operating conditions. In the analysis examples, the benchmark problem for the high temperature reactor vessel which was discussed in the SIE ASME-NH user's seminar was described. Also, the preliminary structural analysis of an Advanced Burner Test Reactor internal structure was described. Considering the load combinations of the various cycle types submitted from significant operating conditions, the integrity of a reactor internal structure was reviewed according to the stress and strain limits of the ASME-NH rules and the analysis and evaluation results were summarized

A Survey of Variable Extragalactic Sources with XTE's All Sky Monitor (ASM)

Science.gov (United States)

Jernigan, Garrett

1998-01-01

The original goal of the project was the near real-time detection of AGN utilizing the SSC 3 of the ASM on XTE which does a deep integration on one 100 square degree region of the sky. While the SSC never performed sufficiently well to allow the success of this goal, the work on the project has led to the development of a new analysis method for coded aperture systems which has now been applied to ASM data for mapping regions near clusters of galaxies such as the Perseus Cluster and the Coma Cluster. Publications are in preparation that describe both the new method and the results from mapping clusters of galaxies.

Interpreting ASME limits and philosophy in FEA of pressure vessel parts

International Nuclear Information System (INIS)

Bezerra, L.M.; Cruz, J.R.B.; Miranda, C.A.J.; Neto, M.M.

1995-01-01

In recent years there has been an effort to interpret finite element (FE) stress results on the light of the ASME B and PV rules and philosophy. Many task groups have issued guidelines on stress linearization and classifications. All those attempts have come up trying to cope modern FE techniques with the rules imposed by the ASME Code. This paper is an independent contribution to the Pressure Vessel Research Council (PVRC) groups which are studying the stress classification and the failure mechanism in a FE framework. This work tries to complement the interesting work by Hollinger and Hechmer presented in the PVP-94 in Minneapolis. In that paper, the authors examined a typical support skirt and showed relations between the skirt collapse load obtained by finite element analysis and the loads allowed from the ASME stress limits. To complement such paper, in the present article, different skirt geometry configurations are analyzed. The configurations here investigated consist of similar support skirts but with different angles of attachments between cylinder and cone parts. It will be possible to observe the influence of the bending stress in the collapse load and its relation to the allowable loads inferred from the ASME limits. A pressure vessel with torispherical head under internal pressure is also examined. Using elastic and limit load FEA, the present paper determines the collapse loads of the configurations. It sets up the relations between these collapse loads, stress categories, and limits dictated by the ASME Code Subsection NB. On the light of NB rules and philosophy, this paper shows how different methods of stress assessment, classification, and limits may influence in the design of a pressure vessel

ASME nuclear codes and standards risk management strategic plan

International Nuclear Information System (INIS)

Balkey, Kenneth R.

2003-01-01

Over the past 15 years, several risk-informed initiatives have been completed or are under development within the ASME Nuclear Codes and Standards organization. In order to better manage the numerous initiatives in the future, the ASME Board on Nuclear Codes and Standards has recently developed and approved a Risk Management Strategic Plan. This paper presents the latest approved version of the plan beginning with a background of applications completed to date, including the recent issuance of the ASME Standard for Probabilistic Risk Assessment (PRA) for Nuclear Power Plant Applications. The paper discusses potential applications within ASME Nuclear Codes and Standards that may require expansion of the PRA Standard, such as for new generation reactors, or the development of new PRA Standards. A long-term vision for the potential development and evolution to a nuclear systems code that adopts a risk-informed approach across a facility life-cycle (design, construction, operation, maintenance, and closure) is summarized. Finally, near term and long term actions are defined across the ASME Nuclear Codes and Standards organizations related to risk management, and related U.S. regulatory activities are also summarized. (author)

Modification of the ASME code z-factor for circumferential surface crack in nuclear ferritic pipings

International Nuclear Information System (INIS)

Choi, Young Hwan; Chung, Yon Ki; Koh, Wan Young; Lee, Joung Bae

1996-01-01

The purpose of this paper is to modify the ASME Code Z-Factor, which is used in the evaluation of circumferential surface crack in nuclear ferritic pipings. The ASME Code Z-Factor is a load multiplier to compensate plastic load with elasto-plastic load. The current ASME Code Z-Factor underestimates pipe maximum load. In this study, the original SC. TNP method is modified first because the original SC. TNP method has a problem that the maximum allowable load predicted from the original SC. TNP method is slightly higher than that measured from the experiment. Then the new Z-Factor is developed using the modified SC. TNP method. The desirability of both the modified SC. TNP method and the new Z-Factor is examined using the experimental results for the circumferential surface crack in pipings. The results show that (1) the modified SC. TNP method is good for predicting the circumferential surface crack behavior in pipings, and (2) the Z-Factor obtained from the modified SC. TNP method well predicts the behavior of circumferential surface crack in ferritic pipings. 30 refs., 13 figs., 4 tabs. (author)

Computer Program of SIE ASME-NH (Revision 1.0) Code

Energy Technology Data Exchange (ETDEWEB)

Koo, Gyeong Hoi; Lee, J. H

2008-01-15

In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail.

Computer Program of SIE ASME-NH (Revision 1.0) Code

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, J. H.

2008-01-01

In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail

Recent development in the ASME O and M committee codes, standards, and guides

International Nuclear Information System (INIS)

Rowley, C.W.

1999-01-01

The ASME O and M Committee continues to expand and update its code, standards, and guides as contained in the ASME OM Code and the ASME OM Standards/Guides. This paper will describe recent changes to these two ASME documents, including technical inquiries, code cases, and the major reformat of the ASME OM Code 1998 Edition. Also two new Parts to the ASME OM S/G will be discussed: OM Part 23 and OM Part 24, which are close to being initially published. A third new Part to the ASME OM S/G has been authorized and has recently started to get organized: Part 26, 'Thermal Calibration of RTDs'. In addition this paper will describe the future plans for these two documents as provided in the O and M Committee Strategic Plan. (author)

Future direction of ASME nuclear codes and standards

International Nuclear Information System (INIS)

Ennis, Kevin; Sheehan, Mark E.

2003-01-01

While the nuclear power industry in the US is in a period of stasis, there continues to be a great deal of activity in the ASME nuclear standards development arena. As plants age, the need for new approaches in standardization changes with the changing needs of the industry. New tools are becoming available in the form of risk analysis, and this is finding its way into more and more of ASME's standards activities. This paper will take a look at the direction that ASME nuclear Codes and Standards are heading in this and other areas, as well as taking a look at some advance reactor concepts and plans for standards to address new technologies

ASME and RCC-MR comparison for the prevention of fatigue analysis

International Nuclear Information System (INIS)

Autrusson, B.; Acker, D.

1989-01-01

The purpose of this survey is to compare the simplified methods, without reference to the safety factor allowed for the mechanical properties. An application of both codes, RCC-MR and ASME, on the design of the wall mock-up of the NET project is made and also an estimation with an elastoplastic analysis. In the case of fatigue analysis according to ASME in the plastic field, the elastic stress is magnified by a K e factor derived from stress variation, S n , disregarding geometrical discontinuities. According to RCC-MR, the elastic maximum strain will magnified by two coefficients accounting for plasticity and variation of Poisson ratio

ASM Based Synthesis of Handwritten Arabic Text Pages

Directory of Open Access Journals (Sweden)

Laslo Dinges

2015-01-01

Full Text Available Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

ASM Based Synthesis of Handwritten Arabic Text Pages.

Science.gov (United States)

Dinges, Laslo; Al-Hamadi, Ayoub; Elzobi, Moftah; El-Etriby, Sherif; Ghoneim, Ahmed

2015-01-01

Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs) based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

Dynamic fracture toughness of ASME SA508 Class 2a ASME SA533 grade A Class 2 base and heat affected zone material and applicable weld metals

International Nuclear Information System (INIS)

Logsdon, W.A.; Begley, J.A.; Gottshall, C.L.

1978-03-01

The ASME Boiler and Pressure Vessel Code, Section III, Article G-2000, requires that dynamic fracture toughness data be developed for materials with specified minimum yield strengths greater than 50 ksi to provide verification and utilization of the ASME specified minimum reference toughness K/sub IR/ curve. In order to qualify ASME SA508 Class 2a and ASME SA533 Grade A Class 2 pressure vessel steels (minimum yield strengths equal 65 kip/in. 2 and 70 kip/in. 2 , respectively) per this requirement, dynamic fracture toughness tests were performed on these materials. All dynamic fracture toughness values of SA508 Class 2a base and HAZ material, SA533 Grade A Class 2 base and HAZ material, and applicable weld metals exceeded the ASME specified minimum reference toughness K/sub IR/ curve

3D automatic anatomy segmentation based on iterative graph-cut-ASM

International Nuclear Information System (INIS)

Chen, Xinjian; Bagci, Ulas

2011-01-01

Purpose: This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. Methods: The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al.[Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. Results: The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 deg. and 0.03, and over all foot bones are about 3.5709 mm, 0.35 deg. and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and

Penetration of ASM 981 in canine skin: a comparative study.

Science.gov (United States)

Gutzwiller, Meret E Ricklin; Reist, Martin; Persohn, Elke; Peel, John E; Roosje, Petra J

2006-01-01

ASM 981 has been developed for topical treatment of inflammatory skin diseases. It specifically inhibits the production and release of pro-inflammatory cytokines. We measured the skin penetration of ASM 981 in canine skin and compared penetration in living and frozen skin. To make penetration of ASM 981 visible in dog skin, tritium labelled ASM 981 was applied to a living dog and to defrosted skin of the same dog. Using qualitative autoradiography the radioactive molecules were detected in the lumen of the hair follicles until the infundibulum, around the superficial parts of the hair follicles and into a depth of the dermis of 200 to 500 microm. Activity could not be found in deeper parts of the hair follicles, the dermis or in the sebaceous glands. Penetration of ASM 981 is low in canine skin and is only equally spread in the upper third of the dermis 24 hours after application. Penetration in frozen skin takes even longer than in living canine skin but shows the same distribution.

ASME factory authorization system and the situation in Japan

International Nuclear Information System (INIS)

Futagawa, Kiyoshi

1978-01-01

Since about three or four years ago, the enterprises of machinery, iron and steel and welding materials in Japan are paying much attention to the acquisition of ASME (American Society of Mechanical Engineers) certificates or authorization to stamp the code symbols. That is, over 70 factories in Japan have undergone ASME examination, and consequently acquired the authorization or certificates. Such authorization is divided into over 20 kinds, of which about 7 are possessed by the companies in Japan. In nuclear field, the kinds of authorization are N (nuclear vessel), NPT (nuclear vessel parts), NV (nuclear vessel safety valve), and MM (material manufacturing). In non-nuclear fields, they are S (power boilers), U (pressure vessels, in Div. 1), and U2 (pressure vessels in Div. 2). The following matters are described: ASME setup, authorization procedures of ASME for factories, the kinds of authorization, factories in Japan holding the authorization or certificates, and renewal of the authorization. (Mori, K.)

Statistical analysis of the ASME KIc database

International Nuclear Information System (INIS)

Sokolov, M.A.

1998-01-01

The American Society of Mechanical Engineers (ASME) K Ic curve is a function of test temperature (T) normalized to a reference nil-ductility temperature, RT NDT , namely, T-RT NDT . It was constructed as the lower boundary to the available K Ic database. Being a lower bound to the unique but limited database, the ASME K Ic curve concept does not discuss probability matters. However, a continuing evolution of fracture mechanics advances has led to employment of the Weibull distribution function to model the scatter of fracture toughness values in the transition range. The Weibull statistic/master curve approach was applied to analyze the current ASME K Ic database. It is shown that the Weibull distribution function models the scatter in K Ic data from different materials very well, while the temperature dependence is described by the master curve. Probabilistic-based tolerance-bound curves are suggested to describe lower-bound K Ic values

ASM-Triggered Too Observations of Kilohertz Oscillations in Three Atoll Sources

Science.gov (United States)

Kaaret, P.; Swank, Jean (Technical Monitor)

2000-01-01

Three Rossi Timing Explorer (RXTE) observations were carried out for this proposal based on target of opportunity triggers derived from the All-Sky Monitor (ASM) on RXTE. We obtained short observations of 4U1636-536 (15ks) and 4U1735-44 (23ks) and a longer observation of 4U0614+091 (117ks). Our analysis of our observations of the atoll neutron star x-ray binary 4U1735-44 lead to the discovery of a second high frequency quasiperiodic oscillation (QPO) in this source. These results were published in the Astrophysical Journal Letters. The data obtained on the source 4U0614+091 were used in a comprehensive study of this source, which will be published in the Astrophysical Journal. The data from this proposal were particularly critical for that study as they lead to the detection of the highest QPO frequency every found in the x-ray emission from an x-ray binary which will be important in placing limits on the equation of state of nuclear matter.

3D automatic anatomy segmentation based on iterative graph-cut-ASM.

Science.gov (United States)

Chen, Xinjian; Bagci, Ulas

2011-08-01

This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al. [Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 degrees and 0.03, and over all foot bones are about 3.5709 mm, 0.35 degrees and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and all foot bones for

ASME nuclear codes and standards: Scope of coverage and current initiatives

International Nuclear Information System (INIS)

Eisenberg, G. M.

1995-01-01

The objective of this paper is to address the broad scope of coverage of nuclear codes, standards and guides produced and administered by the American Society of Mechanical Engineers (ASME). Background information is provided regarding the evolution of the present activities. Details are provided on current initiatives intended to permit ASME to meet the needs of a changing nuclear industry on a worldwide scale. During the early years of commercial nuclear power, ASME produced a code for the construction of nuclear vessels used in the reactor coolant pressure boundary, containment and auxiliary systems. In response to industry growth, ASME Code coverage soon broadened to include rules for construction of other nuclear components, and inservice inspection of nuclear reactor coolant systems. In the years following this, the scope of ASME nuclear codes, standards and guides has been broadened significantly to include air cleaning activities for nuclear power reactors, operation and maintenance of nuclear power plants, quality assurance programs, cranes for nuclear facilities, qualification of mechanical equipment, and concrete reactor vessels and containments. ASME focuses on globalization of its codes, standards and guides by encouraging and promoting their use in the international community and by actively seeking participation of international members on its technical and supervisory committees and in accreditation activities. Details are provided on current international representation. Initiatives are underway to separate the technical requirements from administrative and enforcement requirements, to convert to hard metric units, to provide for non-U. S. materials, and to provide for translations into non-English languages. ASME activity as an accredited ISO 9000 registrar for suppliers of mechanical equipment is described. Rules are being developed for construction of containment systems for nuclear spent fuel and high-level waste transport packagings. Intensive

Bibliometric Analyses Reveal Patterns of Collaboration between ASMS Members

Science.gov (United States)

Palmblad, Magnus; van Eck, Nees Jan

2018-03-01

We have explored the collaborative network of the current American Society for Mass Spectrometry (ASMS) membership using bibliometric methods. The analysis shows that 4249 members are connected in a single, large, co-authorship graph, including the majority of the most published authors in the field of mass spectrometry. The map reveals topographical differences between university groups and national laboratories, and that the co-authors with the strongest links have long worked together at the same location. We have collected and summarized information on the geographical distribution of members, showing a high coverage of active researchers in North America and Western Europe. Looking at research fields, we could also identify a number of new or `hot' topics among ASMS members. Interactive versions of the maps are available on-line at https://goo.gl/UBNFMQ (collaborative network) and https://goo.gl/WV25vm (research topics). [Figure not available: see fulltext.

Highlights of proposed changes to ANSI/ASME N509-80

International Nuclear Information System (INIS)

Ornberg, S.C.

1987-01-01

The ASME Committee on Nuclear Air and Gas Treatment (CONAGT) are at the time of this writing considering performing maintenance revisions of ANSI N509 and N510 based on the results of a required 5-year review and comments received from users of the standards at workshops and through inquiries. This paper discusses the highlights of the significant revisions to ANSI/ASME N509 and explains the reasons for the changes. It should be emphasized that these revisions are not yet approved by ASME CONAGT, the board of Nuclear Codes and Standards, or ANSI

Equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos

Directory of Open Access Journals (Sweden)

Marta Cristina Rodrigues da Silva

2013-06-01

Full Text Available O objetivo foi analisar e comparar o equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos. Fizeram parte do grupo de estudos 24 sujeitos com idades de 7 a 14 anos divididos em dois grupos: grupo asmático e grupo controle. Para avaliação do equilíbrio corporal utilizou-se uma plataforma de força. Foram utilizadas as condições, olhos abertos e fechados com três tentativas aleatórias, com duração de 30 segundos cada uma. Os resultados apontaram diferença significativa entre os grupos, no teste de equilíbrio com olhos abertos apresentando maior amplitude de deslocamento na direção ântero-posterior (COPap (p = 0,04, e médio lateral (COPml (p = 0,02 no grupo asmático. Enquanto que no teste com olhos fechados a diferença foi significante apenas na amplitude de deslocamento ântero-posterior (COPap (p = 0,02 e Área de Elipse (p=0,03. Desse modo, a asma com suas limitações e consequências parece influenciar negativamente no equilíbrio corporal de seus portadores quando comparados com crianças sem a patologia e da mesma faixa etária.

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

Science.gov (United States)

Luger, T; Van Leent, E J; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knop, J; Knulst, A C; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; Van Der Valk, P G; Bos, J D

2001-04-01

SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy of SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6% and 1.0% in the treatment of patients with atopic dermatitis and to select the concentration to be used in phase III studies. This was a double-blind, randomized, parallel-group, multicentre dose-finding study. A total of 260 patients were randomly assigned to treatment with SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6%, or 1.0%, matching vehicle cream, or the internal control 0.1% betamethasone-17-valerate cream (BMV). Treatment was given twice daily for up to 3 weeks. A clear dose-response relationship for SDZ ASM 981 was evident, with 0.2%, 0.6% and 1.0% SDZ ASM 981 creams all being significantly more effective than vehicle (P = 0.041, 0.001 and 0.008, respectively) in terms of baseline to end-point changes in the Eczema Area Severity Index (EASI) and pruritus score. The 1.0% cream was the most effective SDZ ASM 981 concentration. BMV was more effective than the SDZ ASM 981 creams tested in this study. It appears that the efficacy plateau was not reached with the SDZ ASM 981 creams within 3 weeks treatment. SDZ ASM 981 was well tolerated. Burning or a feeling of warmth were the only adverse events reported more frequently in the 0.6% and 1.0% SDZ ASM 981 treatment groups than in the vehicle treatment group (42.9%, 48.9% and 34.9%, respectively). Few systemic adverse events were reported during the study (headache was the most frequent systemic event reported by 15 of 252 patients) and none was considered to be related to treatment. The local tolerability profile of the 1.0% cream was similar to that of the lower concentrations. 1.0% SDZ ASM 981 cream, which was shown to be safe, well tolerated and

Consideration of the Construction Code for TBM-body in ASME BPVC

International Nuclear Information System (INIS)

Kim, Dongjun; Kim, Yunjae; Kim, Suk Kwon; Park, Sung Dae; Lee, Dong Won

2016-01-01

In this paper, ASME code is briefly introduced, and the TBM-body is classified for selecting the ASME section. With the classification of TBM-body, the appropriate section is determined. Helium Cooled Ceramic Reflector (HCCR) Test Blanket System (TBS) has been designed to research on the functions of breeding blanket by KO TBM team. The functions has three subjects as 1) Tritium breeding, 2) Heat conversion and extraction, and 3) Neutron and Gamma-ray shielding. For the process of design, it is needed to select the appropriate construction code as the design criteria. ITER Organization (IO) has proposed that RCC-MR Edition 2007 ver. shall be used for TBM-shield. Because the TBM-shield is connected to the vacuum boundary. For the other part of TBM-set, TBM-body, there is no constraint on the selected code, and the manufacturer can appropriately select the construction code to apply design and fabrication parts. KO TBM Team has considered whether it is appropriate to choose any code for TBM-body. One of the things is ASME code. The advantage of ASME choice is suitable to the domestic status. In the domestic nuclear plant, ASME or KEPIC code is used as regulatory requirements. Based on this, it is possible to prepare a domestic fusion plant regulatory. In this paper, the construction code of TBM-body was determined in ASME BPVC. For the determination of code, the structure of ASME BPVC was introduced and the classification for TBM-body was conducted by the ITER criteria. And the operation conditions of TBM-body that contained creep and irradiation effects was considered to determine the construction code

Consideration of the Construction Code for TBM-body in ASME BPVC

Energy Technology Data Exchange (ETDEWEB)

Kim, Dongjun; Kim, Yunjae [Korea Univ., Seoul (Korea, Republic of); Kim, Suk Kwon; Park, Sung Dae; Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this paper, ASME code is briefly introduced, and the TBM-body is classified for selecting the ASME section. With the classification of TBM-body, the appropriate section is determined. Helium Cooled Ceramic Reflector (HCCR) Test Blanket System (TBS) has been designed to research on the functions of breeding blanket by KO TBM team. The functions has three subjects as 1) Tritium breeding, 2) Heat conversion and extraction, and 3) Neutron and Gamma-ray shielding. For the process of design, it is needed to select the appropriate construction code as the design criteria. ITER Organization (IO) has proposed that RCC-MR Edition 2007 ver. shall be used for TBM-shield. Because the TBM-shield is connected to the vacuum boundary. For the other part of TBM-set, TBM-body, there is no constraint on the selected code, and the manufacturer can appropriately select the construction code to apply design and fabrication parts. KO TBM Team has considered whether it is appropriate to choose any code for TBM-body. One of the things is ASME code. The advantage of ASME choice is suitable to the domestic status. In the domestic nuclear plant, ASME or KEPIC code is used as regulatory requirements. Based on this, it is possible to prepare a domestic fusion plant regulatory. In this paper, the construction code of TBM-body was determined in ASME BPVC. For the determination of code, the structure of ASME BPVC was introduced and the classification for TBM-body was conducted by the ITER criteria. And the operation conditions of TBM-body that contained creep and irradiation effects was considered to determine the construction code.

Comparison of ASME pressure–temperature limits on the fracture probability for a pressurized water reactor pressure vessel

International Nuclear Information System (INIS)

Chou, Hsoung-Wei; Huang, Chin-Cheng

2017-01-01

Highlights: • P-T limits based on ASME K_I_a curve, K_I_C curve and RI method are presented. • Probabilistic and deterministic methods are used to evaluate P-T limits on RPV. • The feasibility of substituting P-T curves with more operational is demonstrated. • Warm-prestressing effect is critical in determining the fracture probability. - Abstract: The ASME Code Section XI-Appendix G defines the normal reactor startup (heat-up) and shut-down (cool-down) operation limits according to the fracture toughness requirement of reactor pressure vessel (RPV) materials. This paper investigates the effects of different pressure-temperature limit operations on structural integrity of a Taiwan domestic pressurized water reactor (PWR) pressure vessel. Three kinds of pressure-temperature limits based on different fracture toughness requirements – the K_I_a fracture toughness curve of ASME Section XI-Appendix G before 1998 editions, the K_I_C fracture toughness curve of ASME Section XI-Appendix G after 2001 editions, and the risk-informed revision method supplemented in ASME Section XI-Appendix G after 2013 editions, respectively, are established as the loading conditions. A series of probabilistic fracture mechanics analyses for the RPV are conducted employing ORNL’s FAVOR code considering various radiation embrittlement levels under these pressure-temperature limit conditions. It is found that the pressure-temperature operation limits which provide more operational flexibility may lead to higher fracture risks to the RPV. The cladding-induced shallow surface breaking flaws are the most critical and dominate the fracture probability of the RPV under pressure-temperature limit transients. Present study provides a risk-informed reference for the operation safety and regulation viewpoint of PWRs in Taiwan.

ASME nuclear codes and standards: Recent technical initiatives

International Nuclear Information System (INIS)

Feigel, R. E.

1995-01-01

Although nuclear power construction is currently in a hiatus in the US, ASME and its volunteer committees remain committed to continual improvements in the technical requirements in its nuclear codes. This paper provides an overview of several significant recent revisions to ASME' s nuclear codes. Additionally, other important initiatives currently being addressed by ASME committees will be described. With the largest population of operating light water nuclear plants in the world and worldwide use of its nuclear codes, ASME continues to support technical advancements in its nuclear codes and standards. While revisions of various magnitude are an ongoing process, several recent revisions embody significant changes based on state of the art design philosophy and substantial industry experience. In the design area, a significant revisions has recently been approved which will significantly reduce conservatisms in seismic piping design as well as provide simplified design rules. Major revisions have also been made to the requirements for nuclear material manufacturers and suppliers, which should result in clearer understanding of this difficult administrative area of the code. In the area of Section XI inservice rules, substantial studies are underway to investigate the application of probabilistic, risked based inspection in lieu of the current deterministic inspection philosophy. While much work still is required in this area, it is an important potential application of the emerging field of risk based inspection

ASME Evaluation on Grid Mobile E-Commerce Process

OpenAIRE

Dan Chang; Wei Liao

2012-01-01

With the development of E-commerce, more scholars have paid attention to research on Mobile E-commerce and mostly focus on the optimization and evaluation of existing process. This paper researches the evaluation of Mobile E-commerce process with a method called ASME. Based on combing and analyzing current mobile business process and utilizing the grid management theory, mobile business process based on grid are constructed. Firstly, the existing process, namely Non-grid Mobile E-commerce, an...

Comparison of ASME Code NB-3200 and NB-3600 results for fatigue analysis of B31.1 branch nozzles

International Nuclear Information System (INIS)

Nitzel, M.E.; Ware, A.G.; Morton, D.K.

1996-01-01

Fatigue analyses wre conducted on two reactor coolant system branch nozzles in an operating PWR designed to the B31.1 Code, for which no explicit fatigue analysis was required by the licensing basis. These analyses were performed as part of resolving issues connected with NRC's Fatigue Action Plan to determine if the cumulative usage factor (CUF) for these nozzles, using the 1992 ASME Code and representative PWR transients, were comparable to nozzles designed and analyzed to the ASME Code. Both NB-3200 and NB-3600 ASME Code methods were used. NB-3200 analyses included the development of finite element models for each nozzle. Although detailed thermal transients were not available for the plant analyzed, representative transients from similar PWRs were applied in each method. CUFs calculated using NB-3200 methods were significantly less than using NB-3600. The paper points out differences in analysis methods and highlights difficulties and unknowns in performing more detailed analyses to reduce conservative assumptions

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2012-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2011-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

Analysis of the Current Technical Issues on ASME Code and Standard for Nuclear Mechanical Design(2009)

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2009-11-01

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

Analysis of the Current Technical Issues on ASME Code and Standard for Nuclear Mechanical Design(2009)

Energy Technology Data Exchange (ETDEWEB)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2009-11-15

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

Operating nuclear plant feedback to ASME and French codes

International Nuclear Information System (INIS)

Journet, J.; O'Donnell, W.J.

1996-01-01

The French have an advantage in nuclear plant operating experience feedback due to the highly centralized nature of their nuclear industry. There is only one utility in charge of design as well as operations (EDF) and only one reactor vendor (Framatome). The ASME Code has played a key role in resolving technical issues in the design and operation of nuclear plants since the inception of nuclear power. The committee structure of the Code brings an ideal combination of senior technical people with both broad and specialized experience to bear on complex how safe is safe enough technical issues. The authors now see an even greater role for the ASME Code in a proposed new regulatory era for the US nuclear industry. The current legalistic confrontational regulatory era has been quite destructive. There now appears to be a real opportunity to begin a new era of technical consensus as the primary means for resolving safety issues. This change can quickly be brought about by having the industry take operating plant problems and regulatory technical issues directly to the ASME Code for timely resolution. Surprisingly, there is no institution in the US nuclear industry with such a mandate. In fact, the industry is organized to feedback through the Nuclear Regulatory Commission issues which could be far better resolved through the ASME Code. Major regulatory benefits can be achieved by closing this loop and providing systematic interaction with the ASME Code. The essential elements of a new regulatory era and ideas for organizing US institutional industry responsibilities, taken from the French experience, are described in this paper

Regulatory Endorsement Activities for ASME Nuclear Codes and Standards

International Nuclear Information System (INIS)

West, Raymond A.

2006-01-01

The ASME Board on Nuclear Codes and Standards (BNCS) has formed a Task Group on Regulatory Endorsement (TG-RE) that is currently in discussions with the United States Nuclear Regulatory Commission (NRC) to look at suggestions and recommendations that can be used to help with the endorsement of new and revised ASME Nuclear Codes and Standards (NC and S). With the coming of new reactors in the USA in the very near future we need to look at both the regulations and all the ASME NC and S to determine where we need to make changes to support these new plants. At the same time it is important that we maintain our operating plants while addressing ageing management needs of our existing reactors. This is going to take new thinking, time, resources, and money. For all this to take place the regulations and requirements that we use must be clear concise and necessary for safety and to that end both the NRC and ASME are working together to make this happen. Because of the influence that the USA has in the world in dealing with these issues, this paper is written to inform the international nuclear engineering community about the issues and what actions are being addressed under this effort. (author)

Integrin and GPCR Crosstalk in the Regulation of ASM Contraction Signaling in Asthma.

Science.gov (United States)

Teoh, Chun Ming; Tam, John Kit Chung; Tran, Thai

2012-01-01

Airway hyperresponsiveness (AHR) is one of the cardinal features of asthma. Contraction of airway smooth muscle (ASM) cells that line the airway wall is thought to influence aspects of AHR, resulting in excessive narrowing or occlusion of the airway. ASM contraction is primarily controlled by agonists that bind G protein-coupled receptor (GPCR), which are expressed on ASM. Integrins also play a role in regulating ASM contraction signaling. As therapies for asthma are based on symptom relief, better understanding of the crosstalk between GPCRs and integrins holds good promise for the design of more effective therapies that target the underlying cellular and molecular mechanism that governs AHR. In this paper, we will review current knowledge about integrins and GPCRs in their regulation of ASM contraction signaling and discuss the emerging concept of crosstalk between the two and the implication of this crosstalk on the development of agents that target AHR.

Risk-informed technology developments for nuclear power plants within the ASME in 2000-2001

International Nuclear Information System (INIS)

Wesley Rowley, C.; Balkey, K.R.

2001-01-01

The purpose of this paper is to provide information on developments within the ASME to support risk-informing NRC regulations for nuclear power plants. This paper builds on a publication at ICONE-8 that discussed ASME risk-informed nuclear power plant initiatives, both in Research and in Codes and Standards, particularly those related to risk-informing Part 50 of the 10 CFR (Code of federal regulations). During the past year, the ASME BNCS formed a Task Force to focus the Society's efforts to support risk-informing 10 CFR Part 50. Key efforts underway that are guided by the task force include finalizing the ASME PRA (probability risk assessment) Standard, developing a Code Case to risk-inform the repair, replacement, and modification activities for ASME components, and developing a Code Case to risk-inform the safety classification of pressure boundary components. Several other initiatives are also under investigation such as introducing risk insights into other ASME nuclear codes and standards supported by appropriate research and technical basis information. Supplementary information will also be provided to update an initial high level plan of ASME risk-informed initiatives for nuclear power plants that was presented at ICONE-8, including plans to communicate these risk-informed technology developments to the public. The authors included and acknowledged contributions from several other cognizant members of the ASME BNCS (board on nuclear codes standards) Task Group on RIP50 in the paper. (authors)

Statistical re-evaluation of the ASME KIC and KIR fracture toughness reference curves

International Nuclear Information System (INIS)

Wallin, K.

1999-01-01

Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the 'master curve', has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original database was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound master curve has the same inherent degree of safety as originally intended for the K IC -reference curve. Similarly, the 1% lower bound master curve corresponds to the K IR -reference curve. (orig.)

Statistical re-evaluation of the ASME KIC and KIR fracture toughness reference curves

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.

1998-01-01

Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the 'Master curve', has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the Master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original data base was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound Master curve has the same inherent degree of safety as originally intended for the K IC -reference curve. Similarly, the 1% lower bound Master curve corresponds to the K IR -reference curve. (orig.)

Using ASM Podcasts to Excite Undergraduate Students about Current Microbiological Research

Directory of Open Access Journals (Sweden)

Stacey E. Lettini

2014-08-01

Full Text Available Innovative technology is often used as a mechanism to engage students in and out of the classroom and can be used to increase critical thinking skills. Podcasts are an excellent way to introduce students to current topics and research in microbiology. The American Society for Microbiology (ASM produces three podcasts that are microbiologically focused: This Week in Microbiology (TWiM, This Week in Parasitology (TWiP, and This Week in Virology (TWiV. These podcasts are usually presented in a manner similar to a journal club, as the presenters regularly invite guests to discuss current research papers. Since students often find reading scientific literature difficult and get bogged down in the details rather than seeing the over-arching purpose of a paper, these podcasts have been used in a General Microbiology course to introduce recent research articles. The students were first assigned an original research article to read and review, and they were asked to generate questions pertaining to things they did not understand. Next, students listened to the corresponding podcast that discussed the article and used it to answer their questions. This was followed by a classroom discussion of the article and the podcast. The ASM podcast helped to demystify original research by providing details of the experimental design and presentation of the results in a language that is more casual and relatable. Students demonstrated greater critical thinking and comprehension of microbiology literature after listening to the podcast. This activity can be used in a variety of courses in the biology curriculum.

Inhibition of allergen-induced basophil activation by ASM-024, a nicotinic receptor ligand.

Science.gov (United States)

Watson, Brittany M; Oliveria, John Paul; Nusca, Graeme M; Smith, Steven G; Beaudin, Sue; Dua, Benny; Watson, Rick M; Assayag, Evelynne Israël; Cormier, Yvon F; Sehmi, Roma; Gauvreau, Gail M

2014-01-01

Nicotinic acetylcholine receptors (nAChRs) were identified on eosinophils and shown to regulate inflammatory responses, but nAChR expression on basophils has not been explored yet. We investigated surface receptor expression of nAChR α4, α7 and α1/α3/α5 subunits on basophils. Furthermore, we examined the effects of ASM-024, a synthetic nicotinic ligand, on in vitro anti-IgE and in vivo allergen-induced basophil activation. Basophils were enriched from the peripheral blood of allergic donors and the expression of nAChR subunits and muscarinic receptors was determined. Purified basophils were stimulated with anti-IgE in the presence of ASM-024 with or without muscarinic or nicotinic antagonists for the measurement of CD203c expression and histamine release. The effect of 9 days of treatment with 50 and 200 mg ASM-024 on basophil CD203c expression was examined in the blood of mild allergic asthmatics before and after allergen inhalation challenge. nAChR α4, α7 and α1/α3/α5 receptor subunit expression was detected on basophils. Stimulation of basophils with anti-IgE increased CD203c expression and histamine release, which was inhibited by ASM-024 (10(-5) to 10(-)(3) M, p ASM-024 was reversed in the presence of muscarinic and nicotinic antagonists. In subjects with mild asthma, ASM-024 inhalation significantly inhibited basophil CD203c expression measured 24 h after allergen challenge (p = 0.03). This study shows that ASM-024 inhibits IgE- and allergen-induced basophil activation through both nicotinic and muscarinic receptors, and suggests that ASM-024 may be an efficacious agent for modulating allergic asthma responses. © 2015 S. Karger AG, Basel.

Acid Sphingomyelinase (ASM) is a Negative Regulator of Regulatory T Cell (Treg) Development.

Science.gov (United States)

Zhou, Yuetao; Salker, Madhuri S; Walker, Britta; Münzer, Patrick; Borst, Oliver; Gawaz, Meinrad; Gulbins, Erich; Singh, Yogesh; Lang, Florian

2016-01-01

Regulatory T cell (Treg) is required for the maintenance of tolerance to various tissue antigens and to protect the host from autoimmune disorders. However, Treg may, indirectly, support cancer progression and bacterial infections. Therefore, a balance of Treg function is pivotal for adequate immune responses. Acid sphingomyelinase (ASM) is a rate limiting enzyme involved in the production of ceramide by breaking down sphingomyelin. Previous studies in T-cells have suggested that ASM is involved in CD28 signalling, T lymphocyte granule secretion, degranulation, and vesicle shedding similar to the formation of phosphatidylserine-exposing microparticles from glial cells. However, whether ASM affects the development of Treg has not yet been described. Splenocytes, isolated Naive T lymphocytes and cultured T cells were characterized for various immune T cell markers by flow cytometery. Cell proliferation was measured by Carboxyfluorescein succinimidyl ester (CFSE) dye, cell cycle analysis by Propidium Iodide (PI), mRNA transcripts by q-RT PCR and protein expression by Western Blotting respectively. ASM deficient mice have higher number of Treg compared with littermate control mice. In vitro induction of ASM deficient T cells in the presence of TGF-β and IL-2 lead to a significantly higher number of Foxp3+ induced Treg (iTreg) compared with control T-cells. Further, ASM deficient iTreg has less AKT (serine 473) phosphorylation and Rictor levels compared with control iTreg. Ceramide C6 led to significant reduction of iTreg in both ASM deficient and WT mice. The reduction in iTreg leads to induction of IL-1β, IL-6 and IL-17 but not IFN-γ mRNA levels. ASM is a negative regulator of natural and iTreg. © 2016 The Author(s) Published by S. Karger AG, Basel.

ASM-024, a piperazinium compound, promotes the in vitro relaxation of β2-adrenoreceptor desensitized tracheas.

Science.gov (United States)

Israël-Assayag, Evelyne; Beaulieu, Marie-Josée; Cormier, Yvon

2015-01-01

Inhaled β2-adrenoreceptor agonists are widely used in asthma and chronic obstructive pulmonary disease (COPD) for bronchoconstriction relief. β2-Adrenoreceptor agonists relax airway smooth muscle cells via cyclic adenosine monophosphate (cAMP) mediated pathways. However, prolonged stimulation induces functional desensitization of the β2-adrenoreceptors (β2-AR), potentially leading to reduced clinical efficacy with chronic or prolonged administration. ASM-024, a small synthetic molecule in clinical stage development, has shown activity at the level of nicotinic receptors and possibly at the muscarinic level and presents anti-inflammatory and bronchodilator properties. Aerosolized ASM-024 reduces airway resistance in mice and promotes in-vitro relaxation of tracheal and bronchial preparations from animal and human tissues. ASM-024 increased in vitro relaxation response to maximally effective concentration of short-acting beta-2 agonists in dog and human bronchi. Although the precise mechanisms by which ASM-024 promotes airway smooth muscle (ASM) relaxation remain unclear, we hypothesized that ASM-024 will attenuate and/or abrogate agonist-induced contraction and remain effective despite β2-AR tachyphylaxis. β2-AR tachyphylaxis was induced with salbutamol, salmeterol and formoterol on guinea pig tracheas. The addition of ASM-024 relaxed concentration-dependently intact or β2-AR desensitized tracheal rings precontracted with methacholine. ASM-024 did not induce any elevation of intracellular cAMP in isolated smooth muscle cells; moreover, blockade of the cAMP pathway with an adenylate cyclase inhibitor had no significant effect on ASM-024-induced guinea pig trachea relaxation. Collectively, these findings show that ASM-024 elicits relaxation of β2-AR desensitized tracheal preparations and suggest that ASM-024 mediates smooth muscle relaxation through a different target and signaling pathway than β2-adrenergic receptor agonists. These findings suggest ASM-024

Analysis of preservice inspection relief requests and recommendations for ASME code changes

International Nuclear Information System (INIS)

Cook, J.F.

1985-05-01

NRC regulations require that preservice inspection (PSI) of nuclear plants be performed in accordance with referenced editions and addenda of Division 1 rules of Section XI, ''Rules for Inservice Inspection of Nuclear Power Plant Components'', of the ASME Boiler and Pressure Vessel Code (ASME Code). The regulations permit applicants to request and obtain relief from the NRC from specific ASME Code requirements that are determined to be impractical. Applicant requests for relief from preservice inspection (PSI) requirements were compiled and analyzed. From this data, covering a total of 178 relief requests, common problems with examination requirements were identified. Changes to examination requirements to solve selected problems are proposed. By following later ASME Code requirements, 46 out of the 178 relief requests can be eliminated. Implementing proposed Code changes would eliminate another 25 relief requests, leaving 107 relief requests out of the original 178 relief requests covered by this survey

Evaluation of practicality of ASME code, Section XI

International Nuclear Information System (INIS)

Mattu, R.K.; Lauderdale, J.R.; Liu, S.N.; Lance, J.J.

2004-01-01

Many nuclear power plants have found that it is impractical or unduly burdensome to comply with some ASME Boiler and Pressure Code provisions and have sought relief from those provisions from the Nuclear Regulatory Commission. An Electric Power Research Institute (EPRI) project is evaluating such Code provisions and alternatives to them that will meet the safety intent of the Code with less burden on utilities. The methodology is to extract data from an on-line data base of relief requests since 1980, analyse the data to identify burdensome provisions for which there are satisfactory alternatives, and recommend changes in the Code to the ASME. (author)

NIST/ASME Steam Properties Database

Science.gov (United States)

SRD 10 NIST/ASME Steam Properties Database (PC database for purchase)   Based upon the International Association for the Properties of Water and Steam (IAPWS) 1995 formulation for the thermodynamic properties of water and the most recent IAPWS formulations for transport and other properties, this updated version provides water properties over a wide range of conditions according to the accepted international standards.

High Level Analysis, Design and Validation of Distributed Mobile Systems with CoreASM

Science.gov (United States)

Farahbod, R.; Glässer, U.; Jackson, P. J.; Vajihollahi, M.

System design is a creative activity calling for abstract models that facilitate reasoning about the key system attributes (desired requirements and resulting properties) so as to ensure these attributes are properly established prior to actually building a system. We explore here the practical side of using the abstract state machine (ASM) formalism in combination with the CoreASM open source tool environment for high-level design and experimental validation of complex distributed systems. Emphasizing the early phases of the design process, a guiding principle is to support freedom of experimentation by minimizing the need for encoding. CoreASM has been developed and tested building on a broad scope of applications, spanning computational criminology, maritime surveillance and situation analysis. We critically reexamine here the CoreASM project in light of three different application scenarios.

Estimates of margins in ASME Code strength values for stainless steel nuclear piping

International Nuclear Information System (INIS)

Ware, A.G.

1995-01-01

The margins in the ASME Code stainless steel allowable stress values that can be attributed to the variations in material strength are evaluated for nuclear piping steels. Best-fit curves were calculated for the material test data that were used to determine allowable stress values for stainless steels in the ASME Code, supplemented by more recent data, to estimate the mean stresses. The mean yield stresses (on which the stainless steel S m values are based) from the test data are about 15 to 20% greater than the ASME Code yield stress values. The ASME Code yield stress values are estimated to approximately coincide with the 97% confidence limit from the test data. The mean and 97% confidence limit values can be used in the probabilistic risk assessments of nuclear piping

Integrity evaluation for stud female threads on pressure vessel according to ASME code using FEM

International Nuclear Information System (INIS)

Kim, Moon Young; Chung, Nam Yong

2003-01-01

The extension of design life among power plants is increasingly becoming a world-wide trend. Kori no.1 unit in Korea is operating two cycle. It has two man-ways for tube inspection in a steam generator which is one of the important components in a nuclear power plant. Especially, stud bolts for man-way cover have damaged by disassembly and assembly several times and degradation for bolt materials for long term operation. It should be evaluated and compared by ASME code criteria for integrity evaluation. Integrity evaluation criteria which has been made by the manufacturer is not applied on the stud bolts of nuclear pressure vessels directly because it is controlled by the yield stress of ASME code. It can apply evaluation criteria through FEM analysis to damaged female threads and to evaluated safety for helical-coil method which is used according to code case-N-496-1. From analysis results, we found that it is the same results between stress intensity which got from FEM analysis on damaged female threads over 10% by manufacture integrity criteria and 2/3 yield strength criteria on ASME code. It was also confirmed that the helical-coil repair method would be safe

A comparative study for SMART steam generator sizing based on ASME and Russian standard

International Nuclear Information System (INIS)

Kim, Y. W.; Kim, J. I.; Jang, M. H.

2000-01-01

A systematic comparison of ASME and Russian standard with respect to the design of SMART steam generator has been carried out. Classification of allowable stress in the Russian standard is quite different from that of ASME. Allowable stress of Russian standard and stress intensity defined in ASME were compared for various steam generator tube material as a function of design temperature. Equations and methodology of determining the thickness for the important parts of steam generator have been analyzed. For the tube subjected to internal and/or external pressure, Russian standard use the same equation in the sizing of tube with different allowable stress. However, ASME use different equations with the same value of allowable stress intensity. The hydraulic test pressure of ASME was also compared with that of Russian standard. In general, hydraulic test pressure determined by Russian standard is higher since it considers difference between allowable stress of test temperature and that of design temperature

Passport of global nuclear business. ASME code certificate acquirement and inspection practices

International Nuclear Information System (INIS)

Kawabata, Hiroyuki; Terajima, Makoto; Anami, Kazuhiro

2010-01-01

There are possibilities of Japanese nuclear industries to participate in global business such as new and additional construction of nuclear power plants in US and also Asian and other developing countries in the world. It is requisite to acquire ASME code certificate for global business participation, just as passport. This article consists of five papers on present status of ASME code certificate acquirement and inspection practices of nuclear components vendors in the area of Japanese nuclear business. Activities of JSME Committee on Power Generation Facility Codes to make JSME codes corresponded to ASME nuclear codes and standards for their international deployment are also described. (T. Tanaka)

Review of ASME nuclear codes and standards- subcommittee on repairs, replacements, and modifications

International Nuclear Information System (INIS)

Mawson, T.J.

1990-01-01

As requested by the ASME board on Nuclear Codes and Standards, the Pressure Vessel Research Committee initiated a project to review Sections III and XI of the ASME Boiler and Pressure Vessel Code for the purposes of improving, clarifying, providing transition, consistency, compatibility, and simplifying code requirements. The project was organized with six subcommittees to address various Code activities: design; tests and examinations; documentation; quality assurance; repair, replacement and modification; and general requirements. This paper discusses how the subcommittee on repair, replacement and modification was organized to review the repair, replacement and modification requirements of the ASME boiler and pressure vessel code, Section III and Section XI for Class 1, 2, and 3 and MC components and their supports, and other documents of the nuclear industry related to the repair, replacement and modification requirements of the ASME code

[Ca2+]i oscillations in ASM: relationship with persistent airflow obstruction in asthma.

Science.gov (United States)

Sweeney, David; Hollins, Fay; Gomez, Edith; Saunders, Ruth; Challiss, R A John; Brightling, Christopher E

2014-07-01

The cause of airway smooth muscle (ASM) hypercontractility in asthma is not fully understood. The relationship of spontaneous intracellular calcium oscillation frequency in ASM to asthma severity was investigated. Oscillations were increased in subjects with impaired lung function abolished by extracellular calcium removal, attenuated by caffeine and unaffected by verapamil or nitrendipine. Whether modulation of increased spontaneous intracellular calcium oscillations in ASM from patients with impaired lung function represents a therapeutic target warrants further investigation. © 2014 The Authors. Respirology published by Wiley Publishing Asia Pty Ltd on behalf of Asian Pacific Society of Respirology.

Investigating ASME allowable loads with finite element analyses

International Nuclear Information System (INIS)

Mattar Neto, Miguel; Bezerra, Luciano M.; Miranda, Carlos A. de J.; Cruz, Julio R.B.

1995-01-01

The evaluation of nuclear components using finite element analysis (FEA) does not generally fall into the shell type verification adopted by the ASME Code. Consequently, the demonstration that the modes of failure are avoided sometimes is not straightforward. Allowable limits, developed by limit load theory, require the computation of shell membrane and bending stresses. How to calculate these stresses from FEA is not necessarily self-evident. One approach to be considered is to develop recommendations in a case-by-case basis for the most common pressure vessel geometries and loads based on comparison between the results of elastic and plastic FEA. In this paper, FE analyses of common 2D and complex 3D geometries are examined and discussed. It will be clear that in the cases studied, stress separation and categorization are not self-evident and simple tasks to undertake. Certain unclear recommendations of ASME Code can lead the stress analyst to non conservative designs as will be demonstrated in this paper. At the endo of this paper, taking into account comparison between elastic and elastic-plastic FE results from ANSYS some observations, suggestions and conclusions about the degree of conservatism of the ASME recommendations will be addressed. (author)

ASM LabCap's contributions to disease surveillance and the International Health Regulations (2005).

Science.gov (United States)

Specter, Steven; Schuermann, Lily; Hakiruwizera, Celestin; Sow, Mah-Séré Keita

2010-12-03

The revised International Health Regulations [IHR(2005)], which requires the Member States of the World Health Organization (WHO) to develop core capacities to detect, assess, report, and respond to public health threats, is bringing new challenges for national and international surveillance systems. As more countries move toward implementation and/or strengthening of their infectious disease surveillance programs, the strengthening of clinical microbiology laboratories becomes increasingly important because they serve as the first line responders to detect new and emerging microbial threats, re-emerging infectious diseases, the spread of antibiotic resistance, and the possibility of bioterrorism. In fact, IHR(2005) Core Capacity #8, "Laboratory", requires that laboratory services be a part of every phase of alert and response.Public health laboratories in many resource-constrained countries require financial and technical assistance to build their capacity. In recognition of this, in 2006, the American Society for Microbiology (ASM) established an International Laboratory Capacity Building Program, LabCap, housed under the ASM International Board. ASM LabCap utilizes ASM's vast resources and its membership's expertise-40,000 microbiologists worldwide-to strengthen clinical and public health laboratory systems in low and low-middle income countries. ASM LabCap's program activities align with HR(2005) by building the capability of resource-constrained countries to develop quality-assured, laboratory-based information which is critical to disease surveillance and the rapid detection of disease outbreaks, whether they stem from natural, deliberate or accidental causes.ASM LabCap helps build laboratory capacity under a cooperative agreement with the U.S. Centers for Disease Control and Prevention (CDC) and under a sub-contract with the Program for Appropriate Technology in Health (PATH) funded by the United States Agency for International Development (USAID

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

Energy Technology Data Exchange (ETDEWEB)

John, P K; Anto, Y; Mungikar, C P; Wagh, P M [Nuclear Power Corporation of India Ltd., Tarapur (India). Tarapur Atomic Power Station

1994-12-31

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs.

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

International Nuclear Information System (INIS)

John, P.K.; Anto, Y.; Mungikar, C.P.; Wagh, P.M.

1994-01-01

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs

Technical requirements for the ASME PRA standard for nuclear power plant applications

International Nuclear Information System (INIS)

Fleming, Karl N.; Bernsen, Sidney A.; Simard, Ronald L.

2000-01-01

In 1998 the American Society of Mechanical Engineers (ASME) formed the Committee on Nuclear Risk Management (CNRM) and a Project Team to develop a standard on PRAs for use in risk informed applications. This ASME standard is being developed to help provide an adequate level of quality in PRAs that are being used to support ASME initiatives to risk informed in-service inspection (ISI) and in-service testing (IST) of nuclear power plant components. A related need supported by the industry and the U.S. Nuclear Regulatory Commission is to reduce the level of effort that is being expended in pilot applications of risk informed initiatives to address questions about the sufficiency of quality in the supporting PRA models. The purpose of this paper is to discuss the authors' views on some of the technical issues that were encountered in the effort to develop the ASME PRA standard. Draft 12 of this standard has been issued for comment, and is currently being finalized with the aim of releasing the standard in early 2001. (author)

Review of the margins for ASME code fatigue design curve - effects of surface roughness and material variability

International Nuclear Information System (INIS)

Chopra, O. K.; Shack, W. J.

2003-01-01

The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. The Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Existing fatigue strain-vs.-life ((var e psilon)-N) data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of pressure vessel and piping steels. This report provides an overview of the existing fatigue (var e psilon)-N data for carbon and low-alloy steels and wrought and cast austenitic SSs to define the effects of key material, loading, and environmental parameters on the fatigue lives of the steels. Experimental data are presented on the effects of surface roughness on the fatigue life of these steels in air and LWR environments. Statistical models are presented for estimating the fatigue (var e psilon)-N curves as a function of the material, loading, and environmental parameters. Two methods for incorporating environmental effects into the ASME Code fatigue evaluations are discussed. Data available in the literature have been reviewed to evaluate the conservatism in the existing ASME Code fatigue evaluations. A critical review of the margins for ASME Code fatigue design curves is presented

Review of the margins for ASME code fatigue design curve - effects of surface roughness and material variability.

Energy Technology Data Exchange (ETDEWEB)

Chopra, O. K.; Shack, W. J.; Energy Technology

2003-10-03

The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. The Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Existing fatigue strain-vs.-life ({var_epsilon}-N) data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of pressure vessel and piping steels. This report provides an overview of the existing fatigue {var_epsilon}-N data for carbon and low-alloy steels and wrought and cast austenitic SSs to define the effects of key material, loading, and environmental parameters on the fatigue lives of the steels. Experimental data are presented on the effects of surface roughness on the fatigue life of these steels in air and LWR environments. Statistical models are presented for estimating the fatigue {var_epsilon}-N curves as a function of the material, loading, and environmental parameters. Two methods for incorporating environmental effects into the ASME Code fatigue evaluations are discussed. Data available in the literature have been reviewed to evaluate the conservatism in the existing ASME Code fatigue evaluations. A critical review of the margins for ASME Code fatigue design curves is presented.

14 CFR 330.31 - What data must air carriers submit concerning ASMs or RTMs?

Science.gov (United States)

2010-01-01

... combination passenger/cargo carrier, you must have submitted your August 2001 total completed ASM report to... correct an error that you document to the Department, you must not alter the ASM or RTM reports you...

Technical Challenge and Demonstration of Advanced Solution Monitoring and Measurement System (ASMS)

International Nuclear Information System (INIS)

Takaya, A.; Mukai, Y.; Nakamura, H.; Hosoma, T.; Yoshimoto, K.; Tamura, T.; Iwamoto, T.

2010-01-01

JNFL and JAEA have collaboratively started to develop an Advanced Solution Measurement and monitoring System (ASMS) as a part of technical challenge intended for next generation safeguards NDA equipment. After we completed feasibility study by using small detectors, the second stage of ASMS has installed into PCDF tank located in a cell, and then tested and calibrated by Pu nitrate solution experimentally. There was no experience measuring around 50kg Pu inventory directly, so it was very challenging work. The conventional SMMS (Solution Monitoring and Measurement System) that is composed of precision manometers acquires density, level and temperature of solution, so that the sampling and analysis are essential to obtain the nuclear material amount in the tank. The SMMS has two weak points on verification and monitoring of the nuclear material flow and inventory; (1) Direct measurement of the inventory cannot be done, (2) Solution rework and reagent adjustment operation in actual plant will make miss-interpretation on the monitoring evaluation. The purpose of ASMS development is to establish quantitative plutonium mass measurement technique directly by NDA of high concentrated pure plutonium nitrate solution and monitoring capability for solution transfers in a process. The merits of ASMS are considered below; (1) Provide direct Pu measurement and continuous monitoring capability, (2) Eliminate sampling and analysis at IIV, (3) Reduce unmeasured inventory. The target of the measurement uncertainty of ASMS is set less than 6% (1sigma) which is equivalent to meet the detection level of the partial defect at IIV by NDA. Known-alpha coincidence counting technique is applied to the ASMS, which is similar to the NDAs for MOX powder as a principle measurement technique. Especially, three following points are key techniques to establish ASMS. (1) Pre-determination of plutonium isotopic composition because it impacts alpha and rho-zero values to obtain multiplication

The ASM Curriculum Guidelines for Undergraduate Microbiology: A Case Study of the Advocacy Role of Societies in Reform Efforts.

Science.gov (United States)

Horak, Rachel E A; Merkel, Susan; Chang, Amy

2015-05-01

A number of national reports, including Vision and Change in Undergraduate Biology Education: A Call to Action, have called for drastic changes in how undergraduate biology is taught. To that end, the American Society for Microbiology (ASM) has developed new Curriculum Guidelines for undergraduate microbiology that outline a comprehensive curriculum for any undergraduate introductory microbiology course or program of study. Designed to foster enduring understanding of core microbiology concepts, the Guidelines work synergistically with backwards course design to focus teaching on student-centered goals and priorities. In order to qualitatively assess how the ASM Curriculum Guidelines are used by educators and learn more about the needs of microbiology educators, the ASM Education Board distributed two surveys to the ASM education community. In this report, we discuss the results of these surveys (353 responses). We found that the ASM Curriculum Guidelines are being implemented in many different types of courses at all undergraduate levels. Educators indicated that the ASM Curriculum Guidelines were very helpful when planning courses and assessments. We discuss some specific ways in which the ASM Curriculum Guidelines have been used in undergraduate classrooms. The survey identified some barriers that microbiology educators faced when trying to adopt the ASM Curriculum Guidelines, including lack of time, lack of financial resources, and lack of supporting resources. Given the self-reported challenges to implementing the ASM Curriculum Guidelines in undergraduate classrooms, we identify here some activities related to the ASM Curriculum Guidelines that the ASM Education Board has initiated to assist educators in the implementation process.

The ASM Curriculum Guidelines for Undergraduate Microbiology: A Case Study of the Advocacy Role of Societies in Reform Efforts

Directory of Open Access Journals (Sweden)

Rachel E.A. Horak

2015-03-01

Full Text Available A number of national reports, including Vision and Change in Undergraduate Biology Education: A Call to Action, have called for drastic changes in how undergraduate biology is taught. To that end, the American Society for Microbiology (ASM developed new Curriculum Guidelines for undergraduate microbiology that outline a comprehensive curriculum for any undergraduate introductory microbiology course or program of study. Designed to foster enduring understanding of core microbiology concepts, the Guidelines work synergistically with backwards course design to focus teaching on student-centered goals and priorities.  In order to qualitatively assess how the ASM Curriculum Guidelines are used by educators and learn more about the needs of microbiology educators, the ASM Education Board distributed two surveys to the ASM education community. In this report, we discuss results of these surveys (353 responses. We found that the ASM Curriculum Guidelines are being implemented in many different types of courses at all undergraduate levels. Educators indicated that the ASM Curriculum Guidelines were very helpful when planning courses and assessments. We discuss some specific ways in which the ASM Curriculum Guidelines have been used in undergraduate classrooms. The survey identified some barriers that microbiology educators faced when trying to adopt the ASM Curriculum Guidelines, including lack of time, lack of financial resources, and lack of supporting resources. Given the self-reported challenges to implementing the ASM Curriculum Guidelines in undergraduate classrooms, we identify here some activities related to the ASM Curriculum Guidelines that the ASM Education Board has initiated to assist educators in the implementation process.

ASME Section XI philosophy related to operating nuclear plant fatigue damage protection

International Nuclear Information System (INIS)

Gosselin, S.R.

1995-01-01

When faced with operating fatigue concerns, nuclear plants traditionally look to the requirements contained in the original construction design code, ASME Section 3, as a basis for component operability. These rules constitute the requirements for nuclear power plant vessel and component construction and, when combined with the Owner's Design Specification, provide reasonable assurance of reliable operation. However, once construction is complete and operation begins, the purpose of any subsequent evaluations shifts from component ''design qualification'' to component ''fitness for service.'' This is a role that has been assumed for ASME Section 11. This paper presents a philosophy, recently endorsed by the ASME Section 11 Executive Committee, intended to guide future Code activities regarding fatigue and its impact on component serviceability

115-year-old society knows how to reach young scientists: ASM Young Ambassador Program.

Science.gov (United States)

Karczewska-Golec, Joanna

2015-12-25

With around 40,000 members in more than 150 countries, American Society for Microbiology (ASM) faces the challenge of meeting very diverse needs of its increasingly international members base. The newly launched ASM Young Ambassador Program seeks to aid the Society in this effort. Equipped with ASM conceptual support and financing, Young Ambassadors (YAs) design and pursue country-tailored approaches to strengthen the Society's ties with local microbiological communities. In a trans-national setting, the active presence of YAs at important scientific events, such as 16th European Congress on Biotechnology, forges new interactions between ASM and sister societies. The paper presents an overview of the Young Ambassadors-driven initiatives at both global and country levels, and explores the topic of how early-career scientists can contribute to science diplomacy and international relations. Copyright © 2014 Elsevier B.V. All rights reserved.

Approaching application of risk-based inspection to ASME code section XI

International Nuclear Information System (INIS)

Hedden, Owen F.

1995-01-01

This paper will describe current efforts within the ASME Boiler and Pressure Vessel Committee's Subcommittee on Nuclear Inservice Inspection to introduce risk-based technology to optimize inservice inspection of nuclear power plants. The subcommittee is responsible for the content of ASME Boiler and Pressure Vessel Code Section XI, Rules for Inservice Inspection of Nuclear Power Plant Components. The paper will first provide the historical background for the inspection program currently in Section XI. It will then describe the development of new technology through the ASME Center for Research and Technology Development program. Next, the work now going on in two of the groups under the Section XI committee will be described in detail. Each of these two efforts is directed toward the application of new risk-based inspection technology to nuclear piping systems. Finally, the directions of additional research and applications of the technology will be discussed. (author)

Structural and functional analysis of the ASM p.Ala359Asp mutant that causes acid sphingomyelinase deficiency.

Science.gov (United States)

Acuña, Mariana; Castro-Fernández, Víctor; Latorre, Mauricio; Castro, Juan; Schuchman, Edward H; Guixé, Victoria; González, Mauricio; Zanlungo, Silvana

2016-10-21

Niemann-Pick disease (NPD) type A and B are recessive hereditary disorders caused by deficiency in acid sphingomyelinase (ASM). The p.Ala359Asp mutation has been described in several patients but its functional and structural effects in the protein are unknown. In order to characterize this mutation, we modeled the three-dimensional ASM structure using the recent available crystal of the mammalian ASM as a template. We found that the p.Ala359Asp mutation is localized in the hydrophobic core and far from the sphingomyelin binding site. However, energy function calculations using statistical potentials indicate that the mutation causes a decrease in ASM stability. Therefore, we investigated the functional effect of the p.Ala359Asp mutation in ASM expression, secretion, localization and activity in human fibroblasts. We found a 3.8% residual ASM activity compared to the wild-type enzyme, without changes in the other parameters evaluated. These results support the hypothesis that the p.Ala359Asp mutation causes structural alterations in the hydrophobic environment where ASM is located, decreasing its enzymatic activity. A similar effect was observed in other previously described NPDB mutations located outside the active site of the enzyme. This work shows the first full size ASM mutant model describe at date, providing a complete analysis of the structural and functional effects of the p.Ala359Asp mutation over the stability and activity of the enzyme. Copyright © 2016 Elsevier Inc. All rights reserved.

Roles of the outer membrane protein AsmA of Salmonella enterica in the control of marRAB expression and invasion of epithelial cells.

Science.gov (United States)

Prieto, Ana I; Hernández, Sara B; Cota, Ignacio; Pucciarelli, M Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

2009-06-01

A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S. enterica, suggesting that lack of AsmA activates expression of the marRAB operon. Hence, asmA mutations may enhance bile resistance by inducing gene expression changes in the marRAB-controlled Mar regulon. In silico analysis of AsmA structure predicted the existence of one transmembrane domain. Biochemical analysis of subcellular fractions revealed that the asmA gene of S. enterica encodes a protein of approximately 70 kDa located in the outer membrane. Because AsmA is unrelated to known transport and/or efflux systems, we propose that activation of marRAB in asmA mutants may be a consequence of envelope reorganization. Competitive infection of BALB/c mice with asmA(+) and asmA isogenic strains indicated that lack of AsmA attenuates Salmonella virulence by the oral route but not by the intraperitoneal route. Furthermore, asmA mutants showed a reduced ability to invade epithelial cells in vitro.

Comparison of SKIFS 2004:1 and Tillsynshandbok PSA against the ASME PRA Standard and European requirements on PSA

International Nuclear Information System (INIS)

Hellstroem, Per

2005-04-01

Requirements on PSA for risk informed applications are expressed in different international documents. The ASME PRA standard published in spring 2002 is one such document, PSA requirements are also expressed in the European Utility Requirements (EUR) for new reactors. The Swedish PSA requirements are provided in the Swedish regulators (SKI) statutes SKIFS 2004:1. SKI also has a review handbook for PSA activities (SKI report 2003:48). The review handbook is a support during review of the utilities PSA activities and the PSAs themselves. The review handbook expresses SKIs expectations by providing so called important aspects for both the PSA work and the PSAs, A comparison of SKIFS requirements and the important aspects in the Review handbook, on one side, and the requirements on PSA in EUR and ASME on the other side, is presented. The comparison shows a large difference in the level of detail in the different documents, where ASME is most detailed and specific. This is expected since the SKI review handbook not is a 'PSA guide' in the same way as the ASME PRA standard. A direct comparison of the ASME PRA standard requirements with the important aspects in the review handbook cannot answer the question which ASME capacity level that is achieved by a PSA meeting all important aspects. The conclusion is that it is not likely to achieve capacity level 2 and 3, since very few ASME level 3 attributes are explicitly expressed as important aspects, though many are expressed in general terms. The review handbook important aspects that are most similar to the ASME capacity level 1 attributes are initiating events, sequence analysis, and system analysis while less similarity is found for analysis of operator actions data analysis, quantification and containment analysis (level 2). Less similarity is found for capacity level 2 and 3. However, the number of additional ASME attributes on capacity level 2 and 3 are few. There are also important aspects in the review handbook that

Neurospora crassa ASM-1 complements the conidiation defect in a stuA mutant of Aspergillus nidulans.

Science.gov (United States)

Chung, Dawoon; Upadhyay, Srijana; Bomer, Brigitte; Wilkinson, Heather H; Ebbole, Daniel J; Shaw, Brian D

2015-01-01

Aspergillus nidulans StuA and Neurospora crassa ASM-1 are orthologous APSES (ASM-1, PHD1, SOK2, Efg1, StuA) transcription factors conserved across a diverse group of fungi. StuA and ASM-1 have roles in asexual (conidiation) and sexual (ascospore formation) development in both organisms. To address the hypothesis that the last common ancestor of these diverse fungi regulated conidiation with similar genes, asm-1 was introduced into the stuA1 mutant of A. nidulans. Expression of asm-1 complemented defective conidiophore morphology and restored conidia production to wild type levels in stuA1. Expression of asm-1 in the stuA1 strain did not rescue the defect in sexual development. When the conidiation regulator AbaA was tagged at its C-terminus with GFP in A. nidulans, it localized to nuclei in phialides. When expressed in the stuA1 mutant, AbaA::GFP localized to nuclei in conidiophores but no longer was confined to phialides, suggesting that expression of AbaA in specific cell types of the conidiophore was conditioned by StuA. Our data suggest that the function in conidiation of StuA and ASM-1 is conserved and support the view that, despite the great morphological and ontogenic diversity of their condiphores, the last common ancestor of A. nidulans and N. crassa produced an ortholog of StuA that was involved in conidiophore development. © 2015 by The Mycological Society of America.

Statistical analysis of geomagnetic field intensity differences between ASM and VFM instruments onboard Swarm constellation

Science.gov (United States)

De Michelis, Paola; Tozzi, Roberta; Consolini, Giuseppe

2017-02-01

From the very first measurements made by the magnetometers onboard Swarm satellites launched by European Space Agency (ESA) in late 2013, it emerged a discrepancy between scalar and vector measurements. An accurate analysis of this phenomenon brought to build an empirical model of the disturbance, highly correlated with the Sun incidence angle, and to correct vector data accordingly. The empirical model adopted by ESA results in a significant decrease in the amplitude of the disturbance affecting VFM measurements so greatly improving the vector magnetic data quality. This study is focused on the characterization of the difference between magnetic field intensity measured by the absolute scalar magnetometer (ASM) and that reconstructed using the vector field magnetometer (VFM) installed on Swarm constellation. Applying empirical mode decomposition method, we find the intrinsic mode functions (IMFs) associated with ASM-VFM total intensity differences obtained with data both uncorrected and corrected for the disturbance correlated with the Sun incidence angle. Surprisingly, no differences are found in the nature of the IMFs embedded in the analyzed signals, being these IMFs characterized by the same dominant periodicities before and after correction. The effect of correction manifests in the decrease in the energy associated with some IMFs contributing to corrected data. Some IMFs identified by analyzing the ASM-VFM intensity discrepancy are characterized by the same dominant periodicities of those obtained by analyzing the temperature fluctuations of the VFM electronic unit. Thus, the disturbance correlated with the Sun incidence angle could be still present in the corrected magnetic data. Furthermore, the ASM-VFM total intensity difference and the VFM electronic unit temperature display a maximal shared information with a time delay that depends on local time. Taken together, these findings may help to relate the features of the observed VFM-ASM total intensity

Inservice inspection procedures and training according to the ASME code

International Nuclear Information System (INIS)

Greenwald, S.M.; Chockie, L.J.

1987-01-01

Mandatory training of the technical staff at a nuclear power plant is of paramount importance if we are to avoid costly plant shutdowns. This training should include the requirements for both Preservice and Inservice Inspection, in addition to Quality Assurance procedures as required by the American Society of Mechanical Engineers (ASME) Code. The training is best accomplished by utilizing instructors who are thoroughly familiar with plant operations and the ASME Code, as well as serving on one of the Code committees. This paper focuses on the Inservice Inspection procedures and the results of an intensive training effort to implement such procedures. (author)

Corticosteroids reduce IL-6 in ASM cells via up-regulation of MKP-1.

Science.gov (United States)

Quante, Timo; Ng, Yee Ching; Ramsay, Emma E; Henness, Sheridan; Allen, Jodi C; Parmentier, Johannes; Ge, Qi; Ammit, Alaina J

2008-08-01

The mechanisms by which corticosteroids reduce airway inflammation are not completely understood. Traditionally, corticosteroids were thought to inhibit cytokines exclusively at the transcriptional level. Our recent evidence, obtained in airway smooth muscle (ASM), no longer supports this view. We have found that corticosteroids do not act at the transcriptional level to reduce TNF-alpha-induced IL-6 gene expression. Rather, corticosteroids inhibit TNF-alpha-induced IL-6 secretion by reducing the stability of the IL-6 mRNA transcript. TNF-alpha-induced IL-6 mRNA decays at a significantly faster rate in ASM cells pretreated with the corticosteroid dexamethasone (t(1/2) = 2.4 h), compared to vehicle (t(1/2) = 9.0 h; P ASM cells.

Development of ASME Code Section 11 visual examination requirements

International Nuclear Information System (INIS)

Cook, J.F.

1990-01-01

Section XI of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code) defines three types of nondestructive examinations, visual, surface, and volumetric. Visual examination is important since it is the primary examination method for many safety-related components and systems and is also used as a backup examination for the components and systems which receive surface or volumetric examinations. Recent activity in the Section XI Code organization to improve the rules for visual examinations is reviewed and the technical basis for the new rules, which cover illumination, vision acuity, and performance demonstration, is explained

Elastic creep-fatigue evaluation for ASME [American Society of Mechanical Engineers] code

International Nuclear Information System (INIS)

Severud, L.K.; Winkel, B.V.

1987-02-01

Reassessment of past ASME N-47 creep-fatigue rules have been under way by committee members. The new proposed elastic creep-fatigue methods are easier to apply than those previously in the code case. They also provide a wider range of practical application while still providing conservative assessments. It is expected that new N-47 code rules for elastic creep-fatigue evaluation will be adopted in the near future

Modifications to LLNL Plutonium Packaging Systems (PuPS) to achieve ASME VIII UW-13.2(d) Requirements for the DOE Standard 3013-00 Outer Can Weld

International Nuclear Information System (INIS)

Riley, D; Dodson, K

2001-01-01

The Lawrence Livermore National Laboratory (LLNL) Plutonium Packaging System (PuPS) prepares packages to meet the DOE Standard 3013 (Reference 1). The PuPS equipment was supplied by the British Nuclear Fuels Limited (BNFL). The DOE Standard 3013 requires that the welding of the Outer Can meets ASME Section VIII Division 1 (Reference 2). ASME Section VIII references to ASME Section IX (Reference 3) for most of the welding requirements, but UW-13.2 (d) of Section VIII requires a certain depth and width of the weld. In this document the UW-13.2(d) requirement is described as the (a+b)/2t s ratio. This ratio has to be greater than or equal to one to meet the requirements of UW-13.2(d). The Outer Can welds had not been meeting this requirement. Three methods are being followed to resolve this issue: (1) Modify the welding parameters to achieve the requirement, (2) Submit a weld case to ASME that changes the UW-13.2(d) requirement for their review and approval, and (3) Change the requirements in the DOE-STD-3013. Each of these methods are being pursued. This report addresses how the first method was addressed for the LLNL PuPS. The experimental work involved adjusting the Outer Can rotational speed and the power applied to the can. These adjustments resulted in being able to achieve the ASME VIII, UW-13.2(d) requirement

Revision of the ASME nuclear quality assurance standard and its historical background

International Nuclear Information System (INIS)

Suzuki, Tetsuya

2009-01-01

ASME NQA-1-2008 'Quality Assurance Requirements for Nuclear Facility Applications' will be endorsed by US NRC by the end of 2009. This standard will apply to design, construction and operation of nuclear power plants newly erected in USA. It is important to Japanese vendors developing nuclear business in USA. Historical background, significance of revision and main revised points of the ASME nuclear quality assurance standard are described in the present paper. (T. Tanaka)

Cyclin D1 in ASM Cells from Asthmatics Is Insensitive to Corticosteroid Inhibition.

Science.gov (United States)

Allen, Jodi C; Seidel, Petra; Schlosser, Tobias; Ramsay, Emma E; Ge, Qi; Ammit, Alaina J

2012-01-01

Hyperplasia of airway smooth muscle (ASM) is a feature of the remodelled airway in asthmatics. We examined the antiproliferative effectiveness of the corticosteroid dexamethasone on expression of the key regulator of G(1) cell cycle progression-cyclin D1-in ASM cells from nonasthmatics and asthmatics stimulated with the mitogen platelet-derived growth factor BB. While cyclin D1 mRNA and protein expression were repressed in cells from nonasthmatics in contrast, cyclin D1 expression in asthmatics was resistant to inhibition by dexamethasone. This was independent of a repressive effect on glucocorticoid receptor translocation. Our results corroborate evidence demonstrating that corticosteroids inhibit mitogen-induced proliferation only in ASM cells from subjects without asthma and suggest that there are corticosteroid-insensitive proliferative pathways in asthmatics.

Elastic creep-fatigue evaluation for ASME code

International Nuclear Information System (INIS)

Severud, L.K.; Winkel, B.V.

1987-01-01

Experience with applying the ASME Code Case N-47 rules for evaluation of creep-fatigue with elastic analysis results has been problematic. The new elastic evaluation methods are intended to bound the stress level and strain range values needed for use in employing the code inelastic analysis creep-fatigue damage counting procedures. To account for elastic followup effects, ad hoc rules for stress classification, shakedown, and ratcheting are employed. Because elastic followup, inelastic strain concentration, and stress-time effects are accounted for, the design fatigue curves in Case N-47 for inelastic analysis are used instead of the more conservative elastic analysis curves. Creep damage assessments are made using an envelope stress-time history that treats multiple load events and repeated cycles during elevated temperature service life. (orig./GL)

Regulatory Safety Issues in the Structural Design Criteria of ASME Section III Subsection NH and for Very High Temperatures for VHTR & GEN IV

Energy Technology Data Exchange (ETDEWEB)

William J. O’Donnell; Donald S. Griffin

2007-05-07

The objective of this task is to identify issues relevant to ASME Section III, Subsection NH [1], and related Code Cases that must be resolved for licensing purposes for VHTGRs (Very High Temperature Gas Reactor concepts such as those of PBMR, Areva, and GA); and to identify the material models, design criteria, and analysis methods that need to be added to the ASME Code to cover the unresolved safety issues. Subsection NH was originally developed to provide structural design criteria and limits for elevated-temperature design of Liquid Metal Fast Breeder Reactor (LMFBR) systems and some gas-cooled systems. The U.S. Nuclear Regulatory Commission (NRC) and its Advisory Committee for Reactor Safeguards (ACRS) reviewed the design limits and procedures in the process of reviewing the Clinch River Breeder Reactor (CRBR) for a construction permit in the late 1970s and early 1980s, and identified issues that needed resolution. In the years since then, the NRC and various contractors have evaluated the applicability of the ASME Code and Code Cases to high-temperature reactor designs such as the VHTGRs, and identified issues that need to be resolved to provide a regulatory basis for licensing. This Report describes: (1) NRC and ACRS safety concerns raised during the licensing process of CRBR , (2) how some of these issues are addressed by the current Subsection NH of the ASME Code; and (3) the material models, design criteria, and analysis methods that need to be added to the ASME Code and Code Cases to cover unresolved regulatory issues for very high temperature service.

Statistical re-evaluation of the ASME K{sub IC} and K{sub IR} fracture toughness reference curves

Energy Technology Data Exchange (ETDEWEB)

Wallin, K.; Rintamaa, R. [Valtion Teknillinen Tutkimuskeskus, Espoo (Finland)

1998-11-01

Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the `Master curve`, has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the Master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original data base was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound Master curve has the same inherent degree of safety as originally intended for the K{sub IC}-reference curve. Similarly, the 1% lower bound Master curve corresponds to the K{sub IR}-reference curve. (orig.)

Adoption of ASME Code Section XI for ISI to Research Reactors

International Nuclear Information System (INIS)

Tawfik, Y.E.; El-sesy, I.A.; Shaban, H.I.; Ibrahim, M.M.

2002-01-01

ETRR-2 (Second Egyptian thermal research reactor) is a multi-purpose, pool- type reactor with an open water surface and variable core arrangement. The core power is 22 MWth, cooled and moderated by light water and with beryllium reflectors. It contains plate- type fuel elements (MTR type, 19.7% enriched uranium) with aluminum clad. The ETRR-2 reactor consist of 57 systems and around 200 subsystems. These systems contain many mechanical components such as tanks, pipes, valves, pumps, heat exchangers, cooling tower, air compressors, and supports. In this present work, a trial was made to adopt the general requirements of ASME code, section XI to ETRR-2 research reactor. ASME (American Society of Mechanical Engineers) boiler and pressure vessel Code, section XI, provides requirements for in-service inspection (ISI) and in-service testing (IST) of components and systems, and repair/replacement activities in a nuclear power plant. Also, IAEA (International Atomic Energy Authority) has published some recommendations for ISI for research reactors similar to that rules and requirements specified in ASME. The complete ISI program requires several steps that have to be performed in sequence. These steps are described in many logic flow charts (LFC's). These logic flow charts include; the general LFC's for all steps required to complete ISI program, the LFC's for examination requirements, the LFC's for flaw evaluation modules, and the LFC's for acceptability of welds for class 1 components. This program includes, also, the inspection program for welded parts of the reactor components during its lifetime. This inspection program is applied for each system and subsystem of ETRR-2 reactor. It includes the examination area type, the component type, the part to be examined, the weld type, the examination method, the inspection program schedule, and the detailed figures of the welded components. (authors)

Interaction between endoplasmic/sarcoplasmic reticulum stress (ER/SR stress), mitochondrial signaling and Ca(2+) regulation in airway smooth muscle (ASM).

Science.gov (United States)

Delmotte, Philippe; Sieck, Gary C

2015-02-01

Airway inflammation is a key aspect of diseases such as asthma. Several inflammatory cytokines (e.g., TNFα and IL-13) increase cytosolic Ca(2+) ([Ca(2+)]cyt) responses to agonist stimulation and Ca(2+) sensitivity of force generation, thereby enhancing airway smooth muscle (ASM) contractility (hyper-reactive state). Inflammation also induces ASM proliferation and remodeling (synthetic state). In normal ASM, the transient elevation of [Ca(2+)]cyt induced by agonists leads to a transient increase in mitochondrial Ca(2+) ([Ca(2+)]mito) that may be important in matching ATP production with ATP consumption. In human ASM (hASM) exposed to TNFα and IL-13, the transient increase in [Ca(2+)]mito is blunted despite enhanced [Ca(2+)]cyt responses. We also found that TNFα and IL-13 induce reactive oxidant species (ROS) formation and endoplasmic/sarcoplasmic reticulum (ER/SR) stress (unfolded protein response) in hASM. ER/SR stress in hASM is associated with disruption of mitochondrial coupling with the ER/SR membrane, which relates to reduced mitofusin 2 (Mfn2) expression. Thus, in hASM it appears that TNFα and IL-13 result in ROS formation leading to ER/SR stress, reduced Mfn2 expression, disruption of mitochondrion-ER/SR coupling, decreased mitochondrial Ca(2+) buffering, mitochondrial fragmentation, and increased cell proliferation.

Roles of the Outer Membrane Protein AsmA of Salmonella enterica in the Control of marRAB Expression and Invasion of Epithelial Cells▿

OpenAIRE

Prieto, Ana I.; Hernández, Sara B.; Cota, Ignacio; Pucciarelli, M. Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

2009-01-01

A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S....

Regulatory Safety Issues in the Structural Design Criteria of ASME Section III Subsection NH and for Very High Temperatures for VHTR and GEN IV

International Nuclear Information System (INIS)

O'Donnell, William J.; Griffin, Donald S.

2007-01-01

The objective of this task is to identify issues relevant to ASME Section III, Subsection NH [1], and related Code Cases that must be resolved for licensing purposes for VHTGRs (Very High Temperature Gas Reactor concepts such as those of PBMR, Areva, and GA); and to identify the material models, design criteria, and analysis methods that need to be added to the ASME Code to cover the unresolved safety issues. Subsection NH was originally developed to provide structural design criteria and limits for elevated-temperature design of Liquid Metal Fast Breeder Reactor (LMFBR) systems and some gas-cooled systems. The U.S. Nuclear Regulatory Commission (NRC) and its Advisory Committee for Reactor Safeguards (ACRS) reviewed the design limits and procedures in the process of reviewing the Clinch River Breeder Reactor (CRBR) for a construction permit in the late 1970s and early 1980s, and identified issues that needed resolution. In the years since then, the NRC and various contractors have evaluated the applicability of the ASME Code and Code Cases to high-temperature reactor designs such as the VHTGRs, and identified issues that need to be resolved to provide a regulatory basis for licensing. This Report describes: (1) NRC and ACRS safety concerns raised during the licensing process of CRBR , (2) how some of these issues are addressed by the current Subsection NH of the ASME Code; and (3) the material models, design criteria, and analysis methods that need to be added to the ASME Code and Code Cases to cover unresolved regulatory issues for very high temperature service.

New methods of analysis of materials strength data for the ASME Boiler and Pressure Vessel Code

International Nuclear Information System (INIS)

Booker, M.K.; Booker, B.L.P.

1980-01-01

Tensile and creep data of the type used to establish allowable stress levels for the ASME Boiler and Pressure Vessel Code have been examined for type 321H stainless steel. Both inhomogeneous, unbalanced data sets and well-planned homogeneous data sets have been examined. Data have been analyzed by implementing standard manual techniques on a modern digital computer. In addition, more sophisticated techniques, practical only through the use of the computer, have been applied. The result clearly demonstrates the efficacy of computerized techniques for these types of analyses

Technical justification for ASME code section xi crack detection by visual examination

International Nuclear Information System (INIS)

Nickell, R.E.; Rashid, Y.R.

2001-01-01

A critical technical element of nuclear power plant license renewal in the United States is the demonstration that the effects of aging do not compromise the intended safety function(s) of a system, structure, or component during the extended term of operation. The demonstration may take either of two forms. First, it can be shown that the design basis for the system, structure, or component is sufficiently robust that the aging effects have been insignificant through the current license term, and will continue to be insignificant through the extended term. Alternatively, it can be shown that, while the aging effects may be potentially significant, those effects can be managed and functionality maintained by defined programmatic activities during the extended term of operation. The first of the two approaches is generally provided by the construction basis, such as construction in accordance with the ASME Code Section III and other consensus codes and standards. The second of the two approaches is often provided by periodic inservice inspection and testing, in accordance with the ASME Code Section XI. The purpose of the ASME Section XI inspections and tests is to assure that systems, components, and structures are fit for continued service until the next scheduled inspection or test. The purpose of this paper is to document the effectiveness of the current ASME Code Section XI visual examination procedures in detecting the effects of aging for systems, structures, and components that are tolerant of mature cracks. (author)

Nuclear component design ontology building based on ASME codes

International Nuclear Information System (INIS)

Bao Shiyi; Zhou Yu; He Shuyan

2005-01-01

The adoption of ontology analysis in the study of concept knowledge acquisition and representation for the nuclear component design process based on computer-supported cooperative work (CSCW) makes it possible to share and reuse numerous concept knowledge of multi-disciplinary domains. A practical ontology building method is accordingly proposed based on Protege knowledge model in combination with both top-down and bottom-up approaches together with Formal Concept Analysis (FCA). FCA exhibits its advantages in the way it helps establish and improve taxonomic hierarchy of concepts and resolve concept conflict occurred in modeling multi-disciplinary domains. With Protege-3.0 as the ontology building tool, a nuclear component design ontology based ASME codes is developed by utilizing the ontology building method. The ontology serves as the basis to realize concept knowledge sharing and reusing of nuclear component design. (authors)

Simulation and optimization of a coking wastewater biological treatment process by activated sludge models (ASM).

Science.gov (United States)

Wu, Xiaohui; Yang, Yang; Wu, Gaoming; Mao, Juan; Zhou, Tao

2016-01-01

Applications of activated sludge models (ASM) in simulating industrial biological wastewater treatment plants (WWTPs) are still difficult due to refractory and complex components in influents as well as diversity in activated sludges. In this study, an ASM3 modeling study was conducted to simulate and optimize a practical coking wastewater treatment plant (CWTP). First, respirometric characterizations of the coking wastewater and CWTP biomasses were conducted to determine the specific kinetic and stoichiometric model parameters for the consecutive aeration-anoxic-aeration (O-A/O) biological process. All ASM3 parameters have been further estimated and calibrated, through cross validation by the model dynamic simulation procedure. Consequently, an ASM3 model was successfully established to accurately simulate the CWTP performances in removing COD and NH4-N. An optimized CWTP operation condition could be proposed reducing the operation cost from 6.2 to 5.5 €/m(3) wastewater. This study is expected to provide a useful reference for mathematic simulations of practical industrial WWTPs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Basic requirements of mechanical properties for nuclear pressure vessel materials in ASME-BPV code

International Nuclear Information System (INIS)

Ning Dong; Yao Weida

2011-01-01

The four basic aspects of strengths, ductility, toughness and fatigue strengths can be summarized for overall mechanical properties requirements of materials for nuclear pressure-retaining vessels in ASME-BPV code. These mechanical property indexes involve in the factors of melting, manufacture, delivery conditions, check or recheck for mechanical properties and chemical compositions, etc. and relate to degradation and damage accumulation during the use of materials. This paper specifically accounts for the basic requirements and theoretic basis of mechanical properties for nuclear pressure vessel materials in ASME-BPV code and states the internal mutual relationships among the four aspects of mechanical properties. This paper focuses on putting forward at several problems on mechanical properties of materials that shall be concerned about during design and manufacture for nuclear pressure vessels according to ASME-BPV code. (author)

Función adrenal y metabolismo lipídico en niños asmáticos tratados con budesonida

Directory of Open Access Journals (Sweden)

Paoli-de Valeri Mariela

1999-01-01

Full Text Available Objetivo. Evaluar el efecto de bajas dosis de budesonida inhalado sobre la función adrenal y el metabolismo lipídico en niños asmáticos. Material y métodos. Se estudiaron: 10 niños asmáticos (edad promedio, 8.6 años tratados con budesonida inhalado (200-300 µg/día por un lapso mayor a tres meses (grupo A; 15 niños asmáticos (edad promedio, 7.8 años sin tratamiento esteroideo (grupo B, y 10 niños no asmáticos (grupo C. Se determinaron los niveles de cortisol basal y postestímulo con ACTH, andrógenos adrenales, lípidos y cortisol urinario. Resultados. Entre los grupos A y B no hubo diferencias significativas en las variables estudiadas. En los niños asmáticos (grupo A-B el cortisol urinario fue significativamente mayor en relación con el grupo C. Los niveles de triglicéridos, colesterol total, colesterol de la lipoproteína de baja densidad e índices aterogénicos fueron mayores en el grupo de niños asmáticos, con y sin budesonida, comparados con el grupo C. Conclusiones. El tratamiento con dosis bajas de budesonida inhalado en niños asmáticos no modificó la función del eje adrenal ni el metabolismo lipídico. Los pacientes asmáticos presentaron un perfil lipídico aterogénico que podría incrementar el riesgo de enfermedad cardiovascular.

The 1997 NRC IST workshops and the status of questions and issues directed to the ASME O and M committee

International Nuclear Information System (INIS)

DiBiasio, A.M.

1998-05-01

This paper describes the results of the four NRC Inservice Testing (IST) Workshops which were held in early 1997 pertaining to NRC Inspection Procedure P 73756, Inservice Testing of Pumps and Valves. It also presents the status of the ASME code committees' resolution of certain questions forwarded to the ASME by the NRC. These questions relate to code interpretations, inconsistencies in the code, and industry concerns that are most appropriately resolved through the ASME consensus process. The ASME committees reviewed the questions at their December 1997 and March 1998 code meetings. Of particular interest are those questions for which the ASME code committees did not agree with the NRC response. These questions, as well as those which the committees provided some additional insight or input, are presented in this paper

ASME code and ratcheting in piping components. Final technical report

International Nuclear Information System (INIS)

Hassan, T.; Matzen, V.C.

1999-01-01

The main objective of this research is to develop an analysis program which can accurately simulate ratcheting in piping components subjected to seismic or other cyclic loads. Ratcheting is defined as the accumulation of deformation in structures and materials with cycles. This phenomenon has been demonstrated to cause failure to piping components (known as ratcheting-fatigue failure) and is yet to be understood clearly. The design and analysis methods in the ASME Boiler and Pressure Vessel Code for ratcheting of piping components are not well accepted by the practicing engineering community. This research project attempts to understand the ratcheting-fatigue failure mechanisms and improve analysis methods for ratcheting predictions. In the first step a state-of-the-art testing facility is developed for quasi-static cyclic and seismic testing of straight and elbow piping components. A systematic testing program to study ratcheting is developed. Some tests have already been performed and the rest will be completed by summer'99. Significant progress has been made in the area of constitutive modeling. A number of sophisticated constitutive models have been evaluated in terms of their simulations for a broad class of ratcheting responses. From the knowledge gained from this evaluation study two improved models are developed. These models are demonstrated to have promise in simulating ratcheting responses in piping components. Hence, implementation of these improved models in widely used finite element programs, ANSYS and/or ABAQUS, is in progress. Upon achieving improved finite element programs for simulation of ratcheting, the ASME Code provisions for ratcheting of piping components will be reviewed and more rational methods will be suggested. Also, simplified analysis methods will be developed for operability studies of piping components and systems. Some of the future works will be performed under the auspices of the Center for Nuclear Power Plant Structures

The ASME Section 11 Special Working Group On Plant Life Extension

International Nuclear Information System (INIS)

Katz, L.R.

1990-01-01

The codes and standards applicable to plant life extension have not been identified in the U.S. at this time. However, several initiatives have been taken to establish specific codes and standards pertaining to nuclear plant life extension (PLEX). One of these initiatives, sponsored by ASME, is the Section XI Special Working Group on Plant Life Extension (SWG-PLEX). The SWG-PLEX reports to the ASME Section XI Subcommittee and is responsible for recommending or drafting rules and requirements for modifying Section XI to accommodate age-related degradation to support nuclear plant life extension. This paper summarizes the results and reports the activities of the SWG-PLEX during the 1989/1990 period

Bronchodilatory and anti-inflammatory effects of ASM-024, a nicotinic receptor ligand, developed for the treatment of asthma.

Science.gov (United States)

Assayag, Evelyne Israël; Beaulieu, Marie-Josée; Cormier, Yvon

2014-01-01

Conventional asthma and COPD treatments include the use of bronchodilators, mainly β2-adrenergic agonists, muscarinic receptor antagonists and corticosteroids or leukotriene antagonists as anti-inflammatory agents. These active drugs are administered either separately or given as a fixed-dose combination medication into a single inhaler. ASM-024, a homopiperazinium compound, derived from the structural modification of diphenylmethylpiperazinium (DMPP), has been developed to offer an alternative mechanism of action that could provide symptomatic control through combined anti-inflammatory and bronchodilator properties in a single entity. A dose-dependent inhibition of cellular inflammation in bronchoalveolar lavage fluid was observed in ovalbumin-sensitized mice, subsequently treated for 3 days by nose-only exposure with aerosolized ASM-024 at doses up to 3.8 mg/kg (ED50 = 0.03 mg/kg). The methacholine ED250 values indicated that airway hyperresponsivenness (AHR) to methacholine decreased following ASM-024 administration by inhalation at a dose of 1.5 mg/kg, with a value of 0.145 ± 0.032 mg/kg for ASM 024-treated group as compared to 0.088 ± 0.023 mg/kg for untreated mice. In in vitro isometric studies, ASM-024 elicited dose-dependent relaxation of isolated mouse tracheal, human, and dog bronchial preparations contracted with methacholine and guinea pig tracheas contracted with histamine. ASM-024 showed also a dose and time dependant protective effect on methacholine-induced contraction. Overall, with its combined anti-inflammatory, bronchodilating and bronchoprotective properties, ASM-024 may represent a new class of drugs with a novel pharmacological approach that could prove useful for the chronic maintenance treatment of asthma and, possibly, COPD.

Creep-fatigue damage evaluation for SS-316LN (ORNL PLATES): - RCC-MR vs. ASME SEC III - NH

International Nuclear Information System (INIS)

Sati, Bhuwan Chandra; Jalaldeen, S.; Velusamy, K.; Selvaraj, P.

2016-01-01

Investigations of high temperature tests done on ORNL plate with deformation control loading, under creep-fatigue damage have been presented. The test results with methodology of RCC-MR and ASME-NH life prediction under creep-fatigue loading have been assessed. The stress relaxation effect in calculating the life using RCC-MR under creep-fatigue damage is found to be significant in presence of secondary stress. RCC-MR: 2007 is more realistic number of cycles (predicts 51 number of cycles) as compared to ASME-NH (predicts 312 number of cycles) which is demonstrated by the experimental work (observed 86 numbers of cycles). Between RCC-MR and experimental work, design code seems to be more conservative for life prediction due to creep-fatigue damage. For fatigue damage, the approaches are same and the difference comes from material properties and the starting stress for applying Neuber's rule. ASME approach has the limitation of stress range magnitude. ASME approach predicts lower elastic plus plastic strain for the cases having S* above the linear stress limit. For creep strain and creep damage evaluation, ASME and RCC-MR have different approaches for calculating the stress at the beginning and during the hold period. The RCC-MR takes account of cyclic hardening or softening effects (hardening in the present case of 316 LN) by means of the cyclic stress-strain curve and the benefit of symmetrization effects which are significant for this material. The ASME code neglects these effects and instead relies on an approach based on the isochronous stress-strain curves. (author)

A study on technical issues of materials and design bases in ASME section III subsection NH code

International Nuclear Information System (INIS)

Lee, Hyeong Yeon; Kim, Jong Bum; Yoo, Bong

2000-12-01

In this study, an analysis of evaluation report by ORNL on the technical issues of elevated temperatures design guide line, ASME Code Section III Subsection NH was conducted and a brief evaluation procedure of the creep-fatigue damage was presented. ORNL published the report in 1993 and reviewed the issue areas where code rules or regulatory guides may be lacking or inadequate to ensure safe operation over the expected life cycles for liquid metal reactor systems. From historical viewpoint of the ASME NH code development, ASME Code Case 47 was changed much in 1989 edition, which includes the stress relaxation behavior in creep damage evaluation. Afterwards the 1992 version of CC N-47 was upgraded to Subsection NH in 1995 edition, which is the same with that of CC N-47 1992 edition except few material data. This report brings up the technical and regulatory issues that can not guarantee the safe and reliable operation of the ALMR which got the conceptual design certification from NRC. Twenty three technical issues were raised and settlement methodology were proposed. Additionally, the status of items approved by ASME code subgroup of elevated temperature design committee for the revision of the most recent 1998 edition of ASME NH was described

ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

Directory of Open Access Journals (Sweden)

Yongsoon Kim

Full Text Available In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

Science.gov (United States)

Kim, Yongsoon; Sun, Hong

2012-01-01

In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

ASM-3 Acid Sphingomyelinase Functions as a Positive Regulator of the DAF-2/AGE-1 Signaling Pathway and Serves as a Novel Anti-Aging Target

Science.gov (United States)

Kim, Yongsoon; Sun, Hong

2012-01-01

In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals. PMID:23049887

Abelian Sandpile Model (ASM) and Infinite Volume Limit

Indian Academy of Sciences (India)

ASM- Properties. Any possible sequence of topplings leads to the same stable configuration [Dhar]. The result of particle addition at and subsequent relaxation is given by an operator. £ бвд £ евд £. , where вд £. ¢. ¦. ¤ззз ¤ вг иг . £. ©. ¢ йа£. (Abelian). 7-b ...

The ASM-NSF Biology Scholars Program: An Evidence-Based Model for Faculty Development

Directory of Open Access Journals (Sweden)

Amy L. Chang

2016-05-01

Full Text Available The American Society for Microbiology (ASM established its ASM-NSF (National Science Foundation Biology Scholars Program (BSP to promote undergraduate education reform by 1 supporting biologists to implement evidence-based teaching practices, 2 engaging life science professional societies to facilitate biologists’ leadership in scholarly teaching within the discipline, and 3 participating in a teaching community that fosters disciplinary-level science, technology, engineering, and mathematics (STEM reform. Since 2005, the program has utilized year-long residency training to provide a continuum of learning and practice centered on principles from the scholarship of teaching and learning (SoTL to more than 270 participants (“scholars” from biology and multiple other disciplines. Additionally, the program has recruited 11 life science professional societies to support faculty development in SoTL and discipline-based education research (DBER. To identify the BSP’s long-term outcomes and impacts, ASM engaged an external evaluator to conduct a study of the program’s 2010­–2014 scholars (n = 127 and society partners. The study methods included online surveys, focus groups, participant observation, and analysis of various documents. Study participants indicate that the program achieved its proposed goals relative to scholarship, professional society impact, leadership, community, and faculty professional development. Although participants also identified barriers that hindered elements of their BSP participation, findings suggest that the program was essential to their development as faculty and provides evidence of the BSP as a model for other societies seeking to advance undergraduate science education reform. The BSP is the longest-standing faculty development program sponsored by a collective group of life science societies. This collaboration promotes success across a fragmented system of more than 80 societies representing the life

The ASM-NSF Biology Scholars Program: An Evidence-Based Model for Faculty Development.

Science.gov (United States)

Chang, Amy L; Pribbenow, Christine M

2016-05-01

The American Society for Microbiology (ASM) established its ASM-NSF (National Science Foundation) Biology Scholars Program (BSP) to promote undergraduate education reform by 1) supporting biologists to implement evidence-based teaching practices, 2) engaging life science professional societies to facilitate biologists' leadership in scholarly teaching within the discipline, and 3) participating in a teaching community that fosters disciplinary-level science, technology, engineering, and mathematics (STEM) reform. Since 2005, the program has utilized year-long residency training to provide a continuum of learning and practice centered on principles from the scholarship of teaching and learning (SoTL) to more than 270 participants ("scholars") from biology and multiple other disciplines. Additionally, the program has recruited 11 life science professional societies to support faculty development in SoTL and discipline-based education research (DBER). To identify the BSP's long-term outcomes and impacts, ASM engaged an external evaluator to conduct a study of the program's 2010-2014 scholars (n = 127) and society partners. The study methods included online surveys, focus groups, participant observation, and analysis of various documents. Study participants indicate that the program achieved its proposed goals relative to scholarship, professional society impact, leadership, community, and faculty professional development. Although participants also identified barriers that hindered elements of their BSP participation, findings suggest that the program was essential to their development as faculty and provides evidence of the BSP as a model for other societies seeking to advance undergraduate science education reform. The BSP is the longest-standing faculty development program sponsored by a collective group of life science societies. This collaboration promotes success across a fragmented system of more than 80 societies representing the life sciences and helps

The use of mixed methods research in interdisciplinary educational journals

OpenAIRE

López-Fernández, Olatz; Molina Azorín, José Francisco

2011-01-01

Mixed methods research is becoming increasingly important in several scientific areas. The analysis of prevalence rates is a new line of research that has emerged in mixed methods research, and this methodological approach has only been applied carefully in a handful of journals. The purpose of this article was to analyse the prevalence of mixed methods research in interdisciplinary educational journals. Moreover, the main characteristics of the mixed methods articles identified were examined...

46 CFR 53.01-3 - Adoption of section IV of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section IV of the ASME Boiler and Pressure...) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-3 Adoption of section IV of the ASME Boiler and Pressure Vessel Code. (a) Heating boilers shall be designed, constructed, inspected, tested...

A strategy for implementation of experience based seismic equipment qualification in IEEE and ASME industry standards

International Nuclear Information System (INIS)

Adams, T.M.

1996-01-01

In the past 20 years, extensive data on the performance of mechanical and electric equipment during actual strong motion earthquakes and seismic qualification tests has been accumulated. Recognizing that an experience based approach provides a technically sound and cost effective method for the seismic qualification of some or certain equipment, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment established a Special Working Group to investigate the incorporation of experienced based methods into the industry consensus codes and standards currently used in the seismic qualification of Seismic Category Nuclear Power Plant equipment. This paper presents the strategy (course of action) which was developed by the Special Working Group for meeting this objective of incorporation of experience based seismic qualification standards used in the design and seismic qualification of seismic category nuclear power plant equipment. This strategy was recommended to both chartering organizations, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment for their consideration and implementation. The status of the review and implementation of the Special Working Group's recommended strategy by the sponsoring organization is also discussed

46 CFR 52.01-2 - Adoption of section I of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section I of the ASME Boiler and Pressure...) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-2 Adoption of section I of the ASME Boiler and Pressure Vessel Code. (a) Main power boilers and auxiliary boilers shall be designed, constructed...

Adaptive SLICE method: an enhanced method to determine nonlinear dynamic respiratory system mechanics

International Nuclear Information System (INIS)

Zhao, Zhanqi; Möller, Knut; Guttmann, Josef

2012-01-01

The objective of this paper is to introduce and evaluate the adaptive SLICE method (ASM) for continuous determination of intratidal nonlinear dynamic compliance and resistance. The tidal volume is subdivided into a series of volume intervals called slices. For each slice, one compliance and one resistance are calculated by applying a least-squares-fit method. The volume window (width) covered by each slice is determined based on the confidence interval of the parameter estimation. The method was compared to the original SLICE method and evaluated using simulation and animal data. The ASM was also challenged with separate analysis of dynamic compliance during inspiration. If the signal-to-noise ratio (SNR) in the respiratory data decreased from +∞ to 10 dB, the relative errors of compliance increased from 0.1% to 22% for the ASM and from 0.2% to 227% for the SLICE method. Fewer differences were found in resistance. When the SNR was larger than 40 dB, the ASM delivered over 40 parameter estimates (42.2 ± 1.3). When analyzing the compliance during inspiration separately, the estimates calculated with the ASM were more stable. The adaptive determination of slice bounds results in consistent and reliable parameter values. Online analysis of nonlinear respiratory mechanics will profit from such an adaptive selection of interval size. (paper)

Estimates of the burst reliability of thin-walled cylinders designed to meet the ASME Code allowables

International Nuclear Information System (INIS)

Stancampiano, P.A.; Zemanick, P.P.

1976-01-01

Pressure containment components in nuclear power plants are designed by the conventional deterministic safety factor approach to meet the requirements of the ASME Pressure Vessel Code, Section III. The inevitable variabilities and uncertainties associated with the design, manufacture, installation, and service processes suggest a probabilistic design approach may also be pertinent. Accordingly, the burst reliabilities of two thin-walled 304 SS cylindrical vessels such as might be employed in liquid metal plants are estimated. A large vessel fabricated from rolled plate per ASME SA-240 and a smaller pipe sized vessel also fabricated from rolled plate per ASME SA-358 are considered. The vessels are sized to just meet the allowable ASME Code primary membrance stresses at 800 0 F (427 0 C). The bursting probability that the operating pressure is greater than the burst strength of the cylinders is calculated using stress-strength interference theory by direct Monte Carlo simulation on a high speed digital computer. A sensitivity study is employed to identify those design parameters which have the greatest effect on the reliability. The effects of preservice quality assurance defect inspections on the reliability are also evaluated parametrically

Assessment of induction elbows for an ASME Code application

International Nuclear Information System (INIS)

Panesar, J.S.; Soliman, M.

1991-01-01

The ASME Nuclear Codes impose some specific requirements on the wall thickness uniformity and the out-of-roundness of cross sections of the elbows for Nuclear Power Plant applications. Due to some of these requirements, manufacturing and installation of these elbows can be time consuming and quite expensive. This paper explores the feasibility of using induction elbows for nuclear application from the stress analysis point of view. To this end, three different sizes of 90deg elbows have been analyzed based on the geometry of an 'ASME Code' elbow and an elbow formed by induction bending. The analysis is carried out for internal pressure, in-plane and out-of-plane loads. Based on the results of these three carbon steel elbows, the use of induction elbows in some of the CANDU-PHW (CANadian Deuterium Uranium-Pressurized Heavy Water) power plant applications seems encouraging. However, before the feasibility can be fully confirmed analysis and induction bending tests over a wider range of geometries, loading conditions, and materials are required. (author)

Utilização de Ecolife® e Acibenzolar-s-metil (ASM no controle da antracnose da banana em pós-colheita Use of Ecolife® and Acibenzolar-S-metil (ASM on the control of antracnosis in banana post-harvest

Directory of Open Access Journals (Sweden)

Luciano Marinho Furtado

2010-09-01

Full Text Available O objetivo deste trabalho foi avaliar a ação dos produtos ASM e Ecolife no controle da antracnose pós-colheita em frutos de banana. Frutos sadios de banana, variedades maçã, prata, pacovan e cacau , em fase intermediária de maturação, foram imersos previamente em soluções de ASM e Ecolife e inoculados com Colletotrichum musae. Utilizou-se o delineamento inteiramente casualizado, em esquema fatorial com quatro repetições. Os resultados apresentados demonstraram a eficácia dos produtos nas concentrações de 5 ml/ L (Ecolife e 0,50g/ L (ASM no controle da antracnose nas variedades analisa das. A variedade cacau apresentou menor lesão quando tratada com o Ecolife (5,79 mm. Com relação ao efeito do ASM, a bana na prata demonstrou um melhor resultado, com tamanho médio de lesão de 5,62 mm. Com o decorrer do processo de maturação dos frutos houve um decréscimo na severidade da doença nas quatro variedades estudadas, exceto no tratamento testemunha, que continuou apresentando aumento no tamanho das lesões nos frutos e atingir a polpa ao final da maturação.The aim of this work was to evaluate the effects of ASM and Ecolife on the control of post-harvest antracnosis in banana. Banana fruits of Maçã, Prata, Pacovan and Figo varieties, at intermediate stage of maturation, were immersed in solutions of ASM and Ecolife and inoculated with Colletotrichum musae A completely randomized design was used, at a factorial scheme 4x2 (four varieties x two products with four replicates. The presented results demonstrated the susceptibility of the fruits to the disease, mainly Maça variety with lesion of 17,99 mm. It was demosntrated the effectiveness of products at concentrations of 5ml. L-1 (Ecolife and 0.50g. L-1 (ASM on antracnosis control. The Figo variety presented the smallest injuries when treated with Ecolife (5.79 mm. Regarding ASM effects, Prata variety demonstrated the best performance, with 5.62 mm of injuries diameter

Appropriate nominal stresses for use with ASME Code pressure-loading stress indices for nozzles

International Nuclear Information System (INIS)

Rodabaugh, E.C.

1976-06-01

This program is part of a cooperative effort with industry to develop and verify analytical methods for assessing the safety of nuclear pressure-vessel and piping-system design. The study of nominal stresses and stress indices described is part of a continuing study of design rules for nozzles in pressure vessels being coordinated by the PVRC Subcommittee on Reinforced Openings and External Loadings. Results from these studies are used by appropriate ASME Code groups in drafting new and improved design rules

Recommendations to ASME for code guidelines and criteria for continued operation of equipment

International Nuclear Information System (INIS)

Harvey, J.F.

1993-01-01

In May 1988, the American Society of Mechanical Engineers, ASME, asked the Pressure Vessel Research Council, PVRC, to review the part it should play in the continued operation of equipment originally designed and fabricated to the ASME codes and rules. This was prompted solely by an economic opportunity in which the capital expenditures to replace plants was far more costly than evaluating, repairing, and extending the nominal design life of the individual component. For instance, nuclear plants are normally designed for a life of 40 years, while fossil fired facilities may have been designed for other time lives, yet at the end of their original design life may actually have many useful years remaining. While this action was economically prompted, it inherently involved a two-fold one; namely, (1) safety, (2) legal. There is no question of safety to operating personnel. While codes for fossil components do not specify design lives, their adoption by many states provides a legal means of procedure in event of a mishap. This recognizes a cradle-to-grave safety responsibility. It is toward maintaining ASMEs leadership as a code authority that this report has been prepared

Towards a consensus-based biokinetic model for green microalgae - The ASM-A.

Science.gov (United States)

Wágner, Dorottya S; Valverde-Pérez, Borja; Sæbø, Mariann; Bregua de la Sotilla, Marta; Van Wagenen, Jonathan; Smets, Barth F; Plósz, Benedek Gy

2016-10-15

Cultivation of microalgae in open ponds and closed photobioreactors (PBRs) using wastewater resources offers an opportunity for biochemical nutrient recovery. Effective reactor system design and process control of PBRs requires process models. Several models with different complexities have been developed to predict microalgal growth. However, none of these models can effectively describe all the relevant processes when microalgal growth is coupled with nutrient removal and recovery from wastewaters. Here, we present a mathematical model developed to simulate green microalgal growth (ASM-A) using the systematic approach of the activated sludge modelling (ASM) framework. The process model - identified based on a literature review and using new experimental data - accounts for factors influencing photoautotrophic and heterotrophic microalgal growth, nutrient uptake and storage (i.e. Droop model) and decay of microalgae. Model parameters were estimated using laboratory-scale batch and sequenced batch experiments using the novel Latin Hypercube Sampling based Simplex (LHSS) method. The model was evaluated using independent data obtained in a 24-L PBR operated in sequenced batch mode. Identifiability of the model was assessed. The model can effectively describe microalgal biomass growth, ammonia and phosphate concentrations as well as the phosphorus storage using a set of average parameter values estimated with the experimental data. A statistical analysis of simulation and measured data suggests that culture history and substrate availability can introduce significant variability on parameter values for predicting the reaction rates for bulk nitrate and the intracellularly stored nitrogen state-variables, thereby requiring scenario specific model calibration. ASM-A was identified using standard cultivation medium and it can provide a platform for extensions accounting for factors influencing algal growth and nutrient storage using wastewater resources. Copyright �

Towards a consensus-based biokinetic model for green microalgae – The ASM-A

DEFF Research Database (Denmark)

Wágner, Dorottya Sarolta; Valverde Pérez, Borja; Sæbø, Mariann

2016-01-01

developed to predict microalgal growth. However, none of these models can effectively describe all the relevant processes when microalgal growth is coupled with nutrient removal and recovery from wastewaters. Here, we present a mathematical model developed to simulate green microalgal growth (ASM-A) using...... and substrate availability can introduce significant variability on parameter values for predicting the reaction rates for bulk nitrate and the intracellularly stored nitrogen state-variables, thereby requiring scenario specific model calibration. ASM-A was identified using standard cultivation medium...

Feature extraction for face recognition via Active Shape Model (ASM) and Active Appearance Model (AAM)

Science.gov (United States)

Iqtait, M.; Mohamad, F. S.; Mamat, M.

2018-03-01

Biometric is a pattern recognition system which is used for automatic recognition of persons based on characteristics and features of an individual. Face recognition with high recognition rate is still a challenging task and usually accomplished in three phases consisting of face detection, feature extraction, and expression classification. Precise and strong location of trait point is a complicated and difficult issue in face recognition. Cootes proposed a Multi Resolution Active Shape Models (ASM) algorithm, which could extract specified shape accurately and efficiently. Furthermore, as the improvement of ASM, Active Appearance Models algorithm (AAM) is proposed to extracts both shape and texture of specified object simultaneously. In this paper we give more details about the two algorithms and give the results of experiments, testing their performance on one dataset of faces. We found that the ASM is faster and gains more accurate trait point location than the AAM, but the AAM gains a better match to the texture.

46 CFR 56.60-1 - Acceptable materials and specifications (replaces 123 and Table 126.1 in ASME B31.1).

Science.gov (United States)

2010-10-01

... Fittings and Other Piping Components—Magnetic Particle Examination Method. SP-55 Quality Standard for Steel... certification, use is limited to applications within heat exchangers. 12 Hydrostatic testing of these fittings... and Seamless Wrought Steel Pipe. ASME B36.19M 2004 Stainless Steel Pipe. American Society for Testing...

Progress toward NuPack, the ASME code for Type B containments

International Nuclear Information System (INIS)

Turula, P.

1995-01-01

This paper presented a brief status report on the development of an ASME Code Division for nuclear packaging and discussed some of the more interesting policy decisions as to what is and is not covered in terms of analytical methods, criteria, scope, and other aspects. The process of the development of this Division has been very slow and inconsistent. There were many participants with many diverse interests. The Division 3 rules are close to being ready to be issued. They are a compromise between many needs and the result is certainly not perfect. Opportunities for fine tuning and expanding this document will present themselves after it is issued as future needs become clear

Low appendicular skeletal muscle mass (ASM) with limited mobility and poor health outcomes in middle-aged African Americans.

Science.gov (United States)

Malmstrom, Theodore K; Miller, Douglas K; Herning, Margaret M; Morley, John E

2013-09-01

Recent efforts to provide a consensus definition propose that sarcopenia be considered a clinical syndrome associated with the loss of both skeletal muscle mass and muscle function that occurs with aging. Validation of sarcopenia definitions that include both low muscle mass and poor muscle function is needed. In the population-based African American Health (AAH) study (N = 998 at baseline/wave 1), muscle mass and mobility were evaluated in a clinical testing center in a subsample of N = 319 persons (ages 52-68) at wave 4 (2004). Muscle mass was measured using dual energy x-ray absorptiometry and mobility by a 6-min walk test and 4-m gait walk test. Height corrected appendicular skeletal mass (ASM; 9.0 ± 1.5 in n = 124 males, 8.3 ± 2.2 in n = 195 females) was computed as total lean muscle mass in arms and legs (kilograms) divided by the square of height (meters). Cross-sectional and longitudinal (6-year) associations of low ASM (bottom 25 % AAH sample; ASM with limited mobility (4-m gait walk ≤1 m/s or 6-min walk ASM with limited mobility was associated with IADL difficulties (p = .008) and frailty (p = .040) but not with ADL difficulties or falls in cross-sectional analyses; and with ADL difficulties (p = .022), IADL difficulties (p = .006), frailty (p = .039), and mortality (p = .003) but not with falls in longitudinal analyses adjusted for age and gender. Low ASM alone was marginally associated with mortality (p = .085) but not with other outcomes in cross-sectional or longitudinal analyses. Low ASM with limited mobility is associated with poor health outcomes among late middle-aged African Americans.

A novel anti-inflammatory drug, SDZ ASM 981, for the treatment of skin diseases: in vitro pharmacology.

Science.gov (United States)

Grassberger, M; Baumruker, T; Enz, A; Hiestand, P; Hultsch, T; Kalthoff, F; Schuler, W; Schulz, M; Werner, F J; Winiski, A; Wolff, B; Zenke, G

1999-08-01

SDZ ASM 981, a novel ascomycin macrolactam derivative, has high anti-inflammatory activity in animal models of allergic contact dermatitis and shows clinical efficacy in atopic dermatitis, allergic contact dermatitis and psoriasis, after topical application. Here we report on the in vitro activities of this promising new drug. SDZ ASM 981 inhibits the proliferation of human T cells after antigen-specific or non-specific stimulation. It downregulates the production of Th1 [interleukin (IL)-2, interferon-gamma] and Th2 (IL-4, IL-10) type cytokines after antigen-specific stimulation of a human T-helper cell clone isolated from the skin of an atopic dermatitis patient. SDZ ASM 981 inhibits the phorbol myristate acetate/phytohaemagglutinin-stimulated transcription of a reporter gene coupled to the human IL-2 promoter in the human T-cell line Jurkat and the IgE/antigen-mediated transcription of a reporter gene coupled to the human tumour necrosis factor (TNF)-alpha promoter in the murine mast-cell line CPII. It does not, however, affect the human TNF-alpha promoter controlled transcription of a reporter gene in a murine dendritic cell line (DC18 RGA) after stimulation via the FcgammaRIII receptor. SDZ ASM 981 also prevents the release of preformed pro-inflammatory mediators from mast cells, as shown in the murine cell line CPII after stimulation with IgE/antigen. In summary, these results demonstrate that SDZ ASM 981 is a specific inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro.

Comparative evaluation of structural integrity for ITER blanket shield block based on SDC-IC and ASME code

Energy Technology Data Exchange (ETDEWEB)

Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Ha, Min-Su, E-mail: msha12@nfri.re.kr [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Sa-Woong; Jung, Hun-Chea [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Duck-Hoi [ITER Organization, Route de Vinon sur Verdon - CS 90046, 13067 Sant Paul Lez Durance (France)

2016-11-01

Highlights: • The procedure of structural integrity and fatigue assessment was described. • Case studies were performed according to both SDC-IC and ASME Sec. • III codes The conservatism of the ASME code was demonstrated. • The study only covers the specifically comparable case about fatigue usage factor. - Abstract: The ITER blanket Shield Block is a bulk structure to absorb radiation and to provide thermal shielding to vacuum vessel and external vessel components, therefore the most significant load for Shield Block is the thermal load. In the previous study, the thermo-mechanical analysis has been performed under the inductive operation as representative loading condition. And the fatigue evaluations were conducted to assure structural integrity for Shield Block according to Structural Design Criteria for In-vessel Components (SDC-IC) which provided by ITER Organization (IO) based on the code of RCC-MR. Generally, ASME code (especially, B&PV Sec. III) is widely applied for design of nuclear components, and is usually well known as more conservative than other specific codes. For the view point of the fatigue assessment, ASME code is very conservative compared with SDC-IC in terms of the reflected K{sub e} factor, design fatigue curve and other factors. Therefore, an accurate fatigue assessment comparison is needed to measure of conservatism. The purpose of this study is to provide the fatigue usage comparison resulting from the specified operating conditions shall be evaluated for Shield Block based on both SDC-IC and ASME code, and to discuss the conservatism of the results.

Comparative evaluation of structural integrity for ITER blanket shield block based on SDC-IC and ASME code

International Nuclear Information System (INIS)

Shim, Hee-Jin; Ha, Min-Su; Kim, Sa-Woong; Jung, Hun-Chea; Kim, Duck-Hoi

2016-01-01

Highlights: • The procedure of structural integrity and fatigue assessment was described. • Case studies were performed according to both SDC-IC and ASME Sec. • III codes The conservatism of the ASME code was demonstrated. • The study only covers the specifically comparable case about fatigue usage factor. - Abstract: The ITER blanket Shield Block is a bulk structure to absorb radiation and to provide thermal shielding to vacuum vessel and external vessel components, therefore the most significant load for Shield Block is the thermal load. In the previous study, the thermo-mechanical analysis has been performed under the inductive operation as representative loading condition. And the fatigue evaluations were conducted to assure structural integrity for Shield Block according to Structural Design Criteria for In-vessel Components (SDC-IC) which provided by ITER Organization (IO) based on the code of RCC-MR. Generally, ASME code (especially, B&PV Sec. III) is widely applied for design of nuclear components, and is usually well known as more conservative than other specific codes. For the view point of the fatigue assessment, ASME code is very conservative compared with SDC-IC in terms of the reflected K_e factor, design fatigue curve and other factors. Therefore, an accurate fatigue assessment comparison is needed to measure of conservatism. The purpose of this study is to provide the fatigue usage comparison resulting from the specified operating conditions shall be evaluated for Shield Block based on both SDC-IC and ASME code, and to discuss the conservatism of the results.

ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

International Nuclear Information System (INIS)

Stillo, Andrew; Ricketts, Craig I.

2013-01-01

High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

Energy Technology Data Exchange (ETDEWEB)

Stillo, Andrew [Camfil Farr, 1 North Corporate Drive, Riverdale, NJ 07457 (United States); Ricketts, Craig I. [New Mexico State University, Department of Engineering Technology and Surveying Engineering, P.O. Box 30001 MSC 3566, Las Cruces, NM 88003-8001 (United States)

2013-07-01

High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

Research Methods and Techniques in Spanish Library and Information Science Journals (2012-2014)

Science.gov (United States)

Ferran-Ferrer, Núria; Guallar, Javier; Abadal, Ernest; Server, Adan

2017-01-01

Introduction. This study examines the research methods and techniques used in Spanish journals of library and information science, the topics addressed by papers in these journals and their authorship affiliation. Method. The researchers selected 580 papers published in the top seven Spanish LIS journals indexed in Web of Science and Scopus and…

Conservatism of ASME KIR-reference curve with respect to crack arrest

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.; Nagel, G.

1999-01-01

The conservatism of the RT NDT temperature indexing parameter and the ASME K IR -reference curve with respect to crack arrest toughness, has been evaluated. Based on an analysis of the original ASME K Ia data, it was established that inherently, the ASME K IR -reference curve corresponds to an overall 5% lower bound curve with respect to crack arrest. It was shown that the scatter of crack arrest toughness is essentially material independent and has a standard deviation of 18% and the temperature dependence of K Ia has the same form as predicted by the master curve for crack initiation toughness. The 'built in' offset between the mean 100 MPa√(m) crack arrest temperature, TK Ia , and RT NDT is 38 C (TK Ia =RT NDT +38 C) and the experimental relation between TK Ia and NDT is, TK Ia =NDT+28 C. The K IR -reference curve using NDT as reference temperature will be conservative with respect to the general 5% lower bound K Ia(5%) -curve, with a 75% confidence. The use of RT NDT , instead of NDT, will generally increase the degree of conservatism, both for non-irradiated as well as irradiated materials, close to a 95% confidence level. This trend is pronounced for materials with Charpy-V upper shelf energies below 100 J. It is shown that the K IR -curve effectively constitutes a deterministic lower bound curve for crack arrest. The findings are valid both for nuclear pressure vessel plates, forgings and welds. (orig.)

Conservatism of ASME KIR-reference curve with respect to crack arrest

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.; Nagel, G.

2001-01-01

The conservatism of the RT NDT temperature indexing parameter and the ASME K IR -reference curve with respect to crack arrest toughness, has been evaluated. Based on an analysis of the original ASME K Ia data, it was established that inherently, the ASME K IR -reference curve corresponds to an overall 5% lower bound curve with respect to crack arrest. It was shown that the scatter of crack arrest toughness is essentially material independent and has a standard deviation (S.D.) of 18% and the temperature dependence of K Ia has the same form as predicted by the master curve for crack initiation toughness. The 'built in' offset between the mean 100 MPa√m crack arrest temperature, TK Ia , and RT NDT is 38 deg. C (TK Ia =RT NDT +38 deg. C) and the experimental relation between TK Ia and NDT is, TK Ia =NDT+28 deg. C. The K IR -reference curve using NDT as reference temperature will be conservative with respect to the general 5% lower bound K Ia(5%) -curve, with a 75% confidence. The use of RT NDT , instead of NDT, will generally increase the degree of conservatism, both for non-irradiated as well as irradiated materials, close to a 95% confidence level. This trend is pronounced for materials with Charpy-V upper shelf energies below 100 J. It is shown that the K IR -curve effectively constitutes a deterministic lower bound curve for crack arrest The findings are valid both for nuclear pressure vessel plates, forgings and welds

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Brun, B.; De Crecy, F.

1994-01-01

This paper deals with the application of the adjoint sensitivity method (ASM) to thermal hydraulic codes. The advantage of the method is to use small central processing unit time in comparison with the usual approach requiring one complete code run per sensitivity determination. In the first part the mathematical aspects of the problem are treated, and the applicability of the method of the functional-type response of a thermal hydraulic model is demonstrated. On a simple example of non-linear hyperbolic equation (Burgers equation) the problem has been analysed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the continuous ASM and the discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the discrete ASM constitutes a practical solution for thermal hydraulic codes. The application of the discrete ASM to the thermal hydraulic safety code CATHARE is then presented for two examples. They demonstrate that the discrete ASM constitutes an efficient tool for the analysis of code sensitivity. ((orig.))

Simulation of municipal-industrial full scale WWTP in an arid climate by application of ASM3

Directory of Open Access Journals (Sweden)

Abdelsalam Elawwad

2017-03-01

Full Text Available In developing countries, and due to the high cost of treatment of industrial wastewater, municipal wastewater treatment facilities usually receive a mixture of municipal wastewater and partially treated industrial wastewater. As a result, an increased potential for shock loads with high pollutant concentrations is expected. The use of mathematical modelling of wastewater treatment is highly efficient in such cases. A dynamic model based on activated sludge model no. 3 (ASM3 describing the performance of the activated sludge process at a full scale wastewater treatment plant (WWTP receiving mixed domestic–industrial wastewater located in an arid area is presented. ASM3 was extended by adding the Arrhenius equation to respond to changes in temperature. BioWin software V.4 was used as the model platform. The model was calibrated under steady-state conditions, adjusting only three kinetic and stoichiometric parameters: maximum heterotrophic growth rate (μH = 8 d−1, heterotrophic aerobic decay rate (bH, O2 = 0.18 d−1, and aerobic heterotrophic yield (YH,O2 = 0.4 (gCOD/gCOD. ASM3 was successful in predicting the WWTP performance, as the model was validated with 10 months of routine daily measurements. ASM3 extended with the Arrhenius equation could be helpful in the design and operation of WWTPs with mixed municipal–industrial influent in arid areas.

Auriculoterapia en pacientes asmáticos

Directory of Open Access Journals (Sweden)

Adolfo González Salvador

1997-04-01

Full Text Available Se realiza un estudio para evaluar la eficacia de la auriculopuntura en 30 asmáticos del área de salud de Aguada de Pasajeros, durante los meses de noviembre de 1992 a abril de 1993. El tratamiento se aplicó durante un mes, con seguimiento durante los 5 meses posteriores. Se observó una disminución en la frecuencia, intensidad y duración de las crisis de asma; la mayoría de los pacientes tuvo una evolución satisfactoria y no se presentaron complicaciones. Se concluye que la auriculoterapia es un método útil en pacientes con asma bronquial debido a su eficacia e inocuidadA study was conducted to evaluate the efficacy of auriculopuncture in 30 asthmatic patients from the health area of Aguada de Pasajeros between November, 1992, and April, 1993. The treatment was applied for a month, with a follow-up during the next 5 months. It was observed a reduction in the frequency, intensity and duration of the asthma crises. Most of the patients had a satisfactory evolution and there were no complications. It is concluded that auriculotherapy is a useful method for patients with bronchial asthma due to its effectiveness and innocuousness.

Spectrum of SMPD1 mutations in Asian-Indian patients with acid sphingomyelinase (ASM)-deficient Niemann-Pick disease.

Science.gov (United States)

Ranganath, Prajnya; Matta, Divya; Bhavani, Gandham SriLakshmi; Wangnekar, Savita; Jain, Jamal Mohammed Nurul; Verma, Ishwar C; Kabra, Madhulika; Puri, Ratna Dua; Danda, Sumita; Gupta, Neerja; Girisha, Katta M; Sankar, Vaikom H; Patil, Siddaramappa J; Ramadevi, Akella Radha; Bhat, Meenakshi; Gowrishankar, Kalpana; Mandal, Kausik; Aggarwal, Shagun; Tamhankar, Parag Mohan; Tilak, Preetha; Phadke, Shubha R; Dalal, Ashwin

2016-10-01

Acid sphingomyelinase (ASM)-deficient Niemann-Pick disease is an autosomal recessive lysosomal storage disorder caused by biallelic mutations in the SMPD1 gene. To date, around 185 mutations have been reported in patients with ASM-deficient NPD world-wide, but the mutation spectrum of this disease in India has not yet been reported. The aim of this study was to ascertain the mutation profile in Indian patients with ASM-deficient NPD. We sequenced SMPD1 in 60 unrelated families affected with ASM-deficient NPD. A total of 45 distinct pathogenic sequence variants were found, of which 14 were known and 31 were novel. The variants included 30 missense, 4 nonsense, and 9 frameshift (7 single base deletions and 2 single base insertions) mutations, 1 indel, and 1 intronic duplication. The pathogenicity of the novel mutations was inferred with the help of the mutation prediction software MutationTaster, SIFT, Polyphen-2, PROVEAN, and HANSA. The effects of the identified sequence variants on the protein structure were studied using the structure modeled with the help of the SWISS-MODEL workspace program. The p. (Arg542*) (c.1624C>T) mutation was the most commonly identified mutation, found in 22% (26 out of 120) of the alleles tested, but haplotype analysis for this mutation did not identify a founder effect for the Indian population. To the best of our knowledge, this is the largest study on mutation analysis of patients with ASM-deficient Niemann-Pick disease reported in literature and also the first study on the SMPD1 gene mutation spectrum in India. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Interpretation, with respect to ASME code Case N-318, of limit moment and fatigue tests of lugs welded to pipe

International Nuclear Information System (INIS)

Foster, D.C.; Van Duyne, D.A.; Budlong, L.A.; Muffett, J.W.; Wais, E.A.; Streck, G.; Rodabaugh, E.C.

1990-01-01

Two nonmandatory ASME code cases have been used often in the evaluation of lugs on nuclear-power- plant piping systems. ASME Code Case N-318 provides guidance for evaluation of the design of rectangular cross-section attachments on Class 2 or 3 piping, and ASME Code Case N-122 provides guidance for evaluation of lugs on Class 1 piping. These code cases have been reviewed and evaluated based on available test data. The results indicate that the Code cases are overly conservative. Recommendations for revisions to the cases are presented which, if adopted, will reduce the overconservatism

Non-uniform sampling and wide range angular spectrum method

International Nuclear Information System (INIS)

Kim, Yong-Hae; Byun, Chun-Won; Oh, Himchan; Lee, JaeWon; Pi, Jae-Eun; Heon Kim, Gi; Lee, Myung-Lae; Ryu, Hojun; Chu, Hye-Yong; Hwang, Chi-Sun

2014-01-01

A novel method is proposed for simulating free space field propagation from a source plane to a destination plane that is applicable for both small and large propagation distances. The angular spectrum method (ASM) was widely used for simulating near field propagation, but it caused a numerical error when the propagation distance was large because of aliasing due to under sampling. Band limited ASM satisfied the Nyquist condition on sampling by limiting a bandwidth of a propagation field to avoid an aliasing error so that it could extend the applicable propagation distance of the ASM. However, the band limited ASM also made an error due to the decrease of an effective sampling number in a Fourier space when the propagation distance was large. In the proposed wide range ASM, we use a non-uniform sampling in a Fourier space to keep a constant effective sampling number even though the propagation distance is large. As a result, the wide range ASM can produce simulation results with high accuracy for both far and near field propagation. For non-paraxial wave propagation, we applied the wide range ASM to a shifted destination plane as well. (paper)

Flujo espiratorio máximo en niños asmáticos: Casos y controles

Directory of Open Access Journals (Sweden)

Arturo Recabarren Lozada

1995-04-01

Full Text Available Con el fin de determinar las variaciones del Flujo Espiratorio Máximo (PEF, se estudiaron a 38 niños asmáticos (CASOS en período intercrítico de la enfermedad y a 38 niños sanos (CONTROLES, de ambos sexos comprendidos entre los 5 y 15 años de edad. Los niños asmáticos fueron clasificados por parámetros clínicos en determinado grado de severidad de asma bronquial, determinando el PEF de cada niño objeto de estudio conel mini-Wright Peak Flow Meter, en 2 registros diarios a los 06 y 18 horas, durante 7 días consecutivos, obteniendo la variabilidad del mismo. Se encuentra diferencia en la variabilidad global de niños asmáticos de todos los grados de severidad de la enfermedad comprada con la de los niños normales, con diferencia estadística altamente significativa (p<0.000001. Las variaciones diurnas del PEF ayuda en el diagnóstico del asma bronquial y también son útiles para realizar la catalogación de severidad de la enfermedad. El PEF correlaciona bien con los síntomas presentados por los pacientes y por lo tanto guarda correspondencia con la Hiperreactividad bronquial (HRB del niño asmático. Postulamos que un niño con historia clínica sugestiva, una variabilidad global mayor del 8% indica que el diagnóstico de asma es altamente probable (Rev Med Hered 1995; 6: 76-82

Comparisons of ASME-code fatigue-evaluation methods for nuclear Class 1 piping with Class 2 or 3 piping

International Nuclear Information System (INIS)

Rodabaugh, E.C.

1983-06-01

The fatigue evaluation procedure used in the ASME Boiler and Pressure Vessel Code, Sect. III, Nuclear Power Plant Components, for Class 1 piping is different from the procedure used for Class 2 or 3 piping. The basis for each procedure is described, and correlations between the two procedures are presented. Conditions under which either procedure or both may be unconservative are noted. Potential changes in the Class 2 or 3 piping procedure to explicitly cover all loadings are discussed. However, the report is intended to be informative, and while the contents of the report may guide future Code changes, specific recommendations are not given herein

Analysis of multi lobe journal bearings with surface roughness using finite difference method

Science.gov (United States)

PhaniRaja Kumar, K.; Bhaskar, SUdaya; Manzoor Hussain, M.

2018-04-01

Multi lobe journal bearings are used for high operating speeds and high loads in machines. In this paper symmetrical multi lobe journal bearings are analyzed to find out the effect of surface roughnessduring non linear loading. Using the fourth order RungeKutta method, time transient analysis was performed to calculate and plot the journal centre trajectories. Flow factor method is used to evaluate the roughness and the finite difference method (FDM) is used to predict the pressure distribution over the bearing surface. The Transient analysis is done on the multi lobe journal bearings for threedifferent surface roughness orientations. Longitudinal surface roughness is more effective when compared with isotopic and traverse surface roughness.

Summary of design of nuclear vessels and piping to ASME III (NB, NC, ND) and vessels to BS 5500

International Nuclear Information System (INIS)

Harrop, L.P.

1992-01-01

There is a hierarchy of design code requirements for pressurised components, starting with non-nuclear codes as the minimum and progressing through the ASME III nuclear Classes 3, 2, 1. In establishing and assessing the safety justifications of nuclear plants it is important to have an appreciation of the gradation of requirements in the ASME III design rules and how these go beyond non-nuclear component design rules. There are two broad aspects to the structural integrity of pressurised components, namely the achievement of integrity and the demonstration of integrity. The technical requirements of design codes are associated with achieving integrity while the documentary aspects are usually associated with demonstrating integrity. In practice documents also have a part in achieving integrity in the communication of information between different organisations and personnel involved in the design process. It is not possible to assign simple numerical measures to the relative integrity afforded by non-nuclear codes and the three Classes of ASME III. Instead it is necessary to compare the different requirements of the rules for the various technical and documentary aspects. This paper summarises the most important technical and documentary aspects of the three Classes of the ASME III Code for vessels and the non-nuclear code BS 5500. A similar summary is also provided for the three Classes of ASME III rules for piping. The intention is that the paper provides a basis for appreciating the relative integrity afforded by these various rules. (author)

Application of ASME code AG-1 to YGN 3 ampersand 4 plants, South Korea

International Nuclear Information System (INIS)

Kim, Y.K.; Porco, R.D.; York, Y.D.

1993-01-01

Yonggwang Nuclear Power Plant Units 3 ampersand 4 are located on the southwestern coast of South Korea on the Yellow Sea. The plant is owned by Korea Electric Power Corp. (KEPCO), with the engineering being performed by Korea Power Engineering Co., Inc. (KOPEC) and Sargent and Lundy under a technology transfer agreement. The plants are both 950 Megawatt (electric) pressurized water reactors of US design. Under contract to KEPCO, Korea Heavy Industries and Construction Co., Ltd. and Ellis and Watts, Division of Dynamics Corporation of America, Batavia, Ohio, supplied major components to the YGN plants in compliance to ASME AG-1. These components included safety related Air Cleaning Units, Reactor containment Fan Cooler Units, Air Handling Units, Cubicle Coolers, Duct Electric Heaters, and fans. This paper details the extent of applicability of ASME Code AG-1 to the specific equipment, description of the equipment, conformance, testing, and design required. The paper also discusses the problems encountered in implementing ASME AG-1, working around Code sections that were not complete at contract inception, conflicts in project documents and related problems. Also discussed are the logistics problems, material availability, and quality assurance aspects complicating the applications of ASME AG-1, due to the required Korean content for some components. Based on successfully supplying the equipment referenced above, it has been concluded that AG-1 is a working document and can be successfully implemented. It provides the requirements necessary for performance, design, construction, acceptance testing, and quality assurance of equipment used as components in nuclear air and gas treatment systems in nuclear facilities. The paper also addresses lessons learned and aspects of mixing US design and US built components in Korean built assemblies

Comparison of the ASME Environmental Fatigue Design Curve with the Leax' Low Bound Model

International Nuclear Information System (INIS)

Jeong, Ill Seok; Kim, Wan Jae; Jun, Hyun Ik

2010-01-01

Environmental fatigue issue long time argued between industry and regulator. The issues of the debates are about environmental fatigue data only from experiment laboratories, no evidences in fields, and over conservatism. However, NRC issued the requirement to implement it to the construction design prior to industry practical design code. American Society of Mechanical Engineers (ASME) determined to issue non-mandatory code cases of environmental fatigue design. This paper evaluated the conservatism of the ASME proposed environmental fatigue design curve in comparison with the Leax' low bound approach model of environmental fatigue curve. A group of CF8M cast austenitic stainless steel (CASS) produced in KEPCO Research Center was introduced in the evaluation

Biomedical journals lack a consistent method to detect outcome reporting bias: a cross-sectional analysis.

Science.gov (United States)

Huan, L N; Tejani, A M; Egan, G

2014-10-01

An increasing amount of recently published literature has implicated outcome reporting bias (ORB) as a major contributor to skewing data in both randomized controlled trials and systematic reviews; however, little is known about the current methods in place to detect ORB. This study aims to gain insight into the detection and management of ORB by biomedical journals. This was a cross-sectional analysis involving standardized questions via email or telephone with the top 30 biomedical journals (2012) ranked by impact factor. The Cochrane Database of Systematic Reviews was excluded leaving 29 journals in the sample. Of 29 journals, 24 (83%) responded to our initial inquiry of which 14 (58%) answered our questions and 10 (42%) declined participation. Five (36%) of the responding journals indicated they had a specific method to detect ORB, whereas 9 (64%) did not have a specific method in place. The prevalence of ORB in the review process seemed to differ with 4 (29%) journals indicating ORB was found commonly, whereas 7 (50%) indicated ORB was uncommon or never detected by their journal previously. The majority (n = 10/14, 72%) of journals were unwilling to report or make discrepancies found in manuscripts available to the public. Although the minority, there were some journals (n = 4/14, 29%) which described thorough methods to detect ORB. Many journals seemed to lack a method with which to detect ORB and its estimated prevalence was much lower than that reported in literature suggesting inadequate detection. There exists a potential for overestimation of treatment effects of interventions and unclear risks. Fortunately, there are journals within this sample which appear to utilize comprehensive methods for detection of ORB, but overall, the data suggest improvements at the biomedical journal level for detecting and minimizing the effect of this bias are needed. © 2014 John Wiley & Sons Ltd.

A survey of variable selection methods in two Chinese epidemiology journals

Directory of Open Access Journals (Sweden)

Lynn Henry S

2010-09-01

Full Text Available Abstract Background Although much has been written on developing better procedures for variable selection, there is little research on how it is practiced in actual studies. This review surveys the variable selection methods reported in two high-ranking Chinese epidemiology journals. Methods Articles published in 2004, 2006, and 2008 in the Chinese Journal of Epidemiology and the Chinese Journal of Preventive Medicine were reviewed. Five categories of methods were identified whereby variables were selected using: A - bivariate analyses; B - multivariable analysis; e.g. stepwise or individual significance testing of model coefficients; C - first bivariate analyses, followed by multivariable analysis; D - bivariate analyses or multivariable analysis; and E - other criteria like prior knowledge or personal judgment. Results Among the 287 articles that reported using variable selection methods, 6%, 26%, 30%, 21%, and 17% were in categories A through E, respectively. One hundred sixty-three studies selected variables using bivariate analyses, 80% (130/163 via multiple significance testing at the 5% alpha-level. Of the 219 multivariable analyses, 97 (44% used stepwise procedures, 89 (41% tested individual regression coefficients, but 33 (15% did not mention how variables were selected. Sixty percent (58/97 of the stepwise routines also did not specify the algorithm and/or significance levels. Conclusions The variable selection methods reported in the two journals were limited in variety, and details were often missing. Many studies still relied on problematic techniques like stepwise procedures and/or multiple testing of bivariate associations at the 0.05 alpha-level. These deficiencies should be rectified to safeguard the scientific validity of articles published in Chinese epidemiology journals.

46 CFR 54.01-2 - Adoption of division 1 of section VIII of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... Boiler and Pressure Vessel Code. 54.01-2 Section 54.01-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... division 1 of section VIII of the ASME Boiler and Pressure Vessel Code. (a) Pressure vessels shall be designed, constructed, and inspected in accordance with section VIII of the ASME Boiler and Pressure Vessel...

Effects of ASM-024, a modulator of acetylcholine receptor function, on airway responsiveness and allergen-induced responses in patients with mild asthma.

Science.gov (United States)

Boulet, Louis-Philippe; Gauvreau, Gail M; Cockcroft, Donald W; Davis, Beth; Vachon, Luc; Cormier, Yvon; O'Byrne, Paul M

2015-01-01

To evaluate the safety, tolerability and clinical activity of ASM-024, a new cholinergic compound with dual nicotinic and muscarinic activity, in mild allergic asthma. The present study involved 24 stable, mild allergic asthmatic subjects. In a cross-over design, ASM-024 (50 mg or 200 mg) or placebo were administered once daily by nebulization over three periods of nine consecutive days separated by a three-week washout. The effect of each treatment on the forced expiratory volume in 1 s (FEV1), provocative concentration of methacholine causing a 20% decline in FEV1 (PC20), early and late asthmatic responses, and allergen-induced inflammation were measured. Seventeen subjects completed the study. During treatment with ASM-024 at 50 mg or 200 mg, the PC20 value increased respectively from a mean (± SD) 2.56±3.86 mg/mL to 4.11 mg/mL (P=0.007), and from 3.12±4.37 mg/mL to 5.23 mg/mL (P=0.005) (no change with placebo). On day 7 (day preceding allergen challenge), postdosing FEV1 increased by 2.0% with 50 mg (P=0.005) and 1.9% with 200 mg (P=0.008) (placebo -1.1%). ASM-24 had no inhibitory effect on early and late asthmatic responses, nor on sputum eosinophil or neutrophil levels. ASM-024 induced no serious adverse events, but caused cough in 22% and 48% of the subjects with 50 mg and 200 mg, respectively, compared with 10% who were on placebo. ASM-024 did not inhibit allergen-induced asthmatic response and related airway inflammation, but reduced methacholine airway responsiveness and slightly improved lung function. The mechanism by which ASM-024 improves these outcomes requires further study.

IL-17A acts via p38 MAPK to increase stability of TNF-alpha-induced IL-8 mRNA in human ASM.

Science.gov (United States)

Henness, Sheridan; van Thoor, Eveline; Ge, Qi; Armour, Carol L; Hughes, J Margaret; Ammit, Alaina J

2006-06-01

Human airway smooth muscle (ASM) plays an immunomodulatory role in asthma. Recently, IL-17A has become of increasing interest in asthma, being found at elevated levels in asthmatic airways and emerging as playing an important role in airway neutrophilia. IL-17A predominantly exerts its neutrophil orchestrating role indirectly via the induction of cytokines by resident airway structural cells. Here, we perform an in vitro study to show that although IL-17A did not induce secretion of the CXC chemokine IL-8 from ASM cells, IL-17A significantly potentiates TNF-alpha-induced IL-8 protein secretion and gene expression in a concentration- and time-dependent manner (P ASM cells, acting via a p38 MAPK-dependent posttranscriptional pathway to augment TNF-alpha-induced secretion of the potent neutrophil chemoattractant IL-8 from ASM cells.

Understanding the Long-Term Spectral Variability of Cygnus X-1 from BATSE and ASM Observations

Science.gov (United States)

Zdziarski, Andrzej A.; Poutanen, Juri; Paciesas, William S.; Wen, Linqing; Six, N. Frank (Technical Monitor)

2002-01-01

We present a spectral analysis of observations of Cygnus X-1 by the RXTE/ASM (1.5-12 keV) and CGRO/BATSE (20-300 keV), including about 1200 days of simultaneous data. We find a number of correlations between intensities and hardnesses in different energy bands from 1.5 keV to 300 keV. In the hard (low) spectral state, there is a negative correlation between the ASM 1.5-12 keV flux and the hardness at any energy. In the soft (high) spectral state, the ASM flux is positively correlated with the ASM hardness (as previously reported) but uncorrelated with the BATSE hardness. In both spectral states, the BATSE hardness correlates with the flux above 100 keV, while it shows no correlation with the flux in the 20-100 keV range. At the same time, there is clear correlation between the BATSE fluxes below and above 100 keV. In the hard state, most of the variability can be explained by softening the overall spectrum with a pivot at approximately 50 keV. The observations show that there has to be another, independent variability pattern of lower amplitude where the spectral shape does not change when the luminosity changes. In the soft state, the variability is mostly caused by a variable hard (Comptonized) spectral component of a constant shape superimposed on a constant soft blackbody component. These variability patterns are in agreement with the dependence of the rms variability on the photon energy in the two states. We interpret the observed correlations in terms of theoretical Comptonization models. In the hard state, the variability appears to be driven mostly by changing flux in seed photons Comptonized in a hot thermal plasma cloud with an approximately constant power supply. In the soft state, the variability is consistent with flares of hybrid, thermal/nonthermal, plasma with variable power above a stable cold disk. Also, based on broadband pointed observations simultaneous with those of the ASM and BATSE, we find the intrinsic bolometric luminosity increases by a

Evaluation of flaws in ferritic piping: ASME Code Appendix J, Deformation Plasticity Failure Assessment Diagram (DPFAD)

International Nuclear Information System (INIS)

Bloom, J.M.

1991-08-01

This report summarizes the methods and bases used by an ASME Code procedure for the evaluation of flaws in ferritic piping. The procedure is currently under consideration by the ASME Boiler and Pressure Vessel Code Committee of Section 11. The procedure was initially proposed in 1985 for the evaluation of the acceptability of flaws detected in piping during in-service inspection for certain materials, identified in Article IWB-3640 of the ASME Boiler and Pressure Vessel Code Section 11 ''Rules for In-service Inspection of Nuclear Power Plant Components.'' for which the fracture toughness is not sufficiently high to justify acceptance based solely on the plastic limit load evaluation methodology of Appendix C and IWB-3641. The procedure, referred to as Appendix J, originally included two approaches: a J-integral based tearing instability (J-T) analysis and the deformation plasticity failure assessment diagram (DPFAD) methodology. In Appendix J, a general DPFAD approach was simplified for application to part-through wall flows in ferritic piping through the use of a single DPFAD curve for circumferential flaws. Axial flaws are handled using two DPFAD curves where the ratio of flaw depth to wall thickness is used to determine the appropriate DPFAD curve. Flaws are evaluated in Appendix J by comparing the actual pipe applied stress with the allowable stress with the appropriate safety factors for the flaw size at the end of the evaluation period. Assessment points for circumferential and axial flaws are plotted on the appropriate failure assessment diagram. In addition, this report summarizes the experimental test predictions of the results of the Battelle Columbus Laboratory experiments, the Eiber experiments, and the JAERI tests using the Appendix J DPFAD methodology. Lastly, this report also provides guidelines for handling residual stresses in the evaluation procedure. 22 refs., 13 figs., 5 tabs

Iterative and non-iterative solutions of engine flows using ASM and k-ε turbulence models

International Nuclear Information System (INIS)

Khaleghi, H.; Fallah, E.

2003-01-01

Various turbulent models are widely developed in order to make a good prediction of turbulence phenomena in different applications. The standard k-ε model shows a poor prediction for some applications. The Reynolds Stress Model (RSM) is expected to give a better prediction of turbulent characteristics, because a separate differential equation for each Reynolds stress component is solved in this model. In order to save both time and memory in this calculation a new Algebraic Stress Model (ASM) which was developed by Lumly et al in 1995 is used for calculations of flow characteristics in the internal combustion engine chamber. With using turbulent realizability principles, this model becomes a powerful and reliable turbulence model. In this paper the abilities of the model is examined in internal combustion engine flows. The results of ASM and k-ε models are compared with the experimental data. It is shown that the poor predictions of k-ε model are modified by ASM model. Also in this paper non-iterative PISO and iterative SIMPLE solution algorithms are compared. The results show that the PISO solution algorithm is the preferred and more efficient procedure in the calculation of internal combustion engine. (author)

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

NARCIS (Netherlands)

Luger, T.; Leent, E.J. van; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A.C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; Valk, P.G.M. van der; Bos, J.D.

2001-01-01

BACKGROUND: SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. OBJECTIVES: This study was designed to determine

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

NARCIS (Netherlands)

Luger, T; Van Leent, EJM; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knulst, AC; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; van der Valk, P. G. M.; Bos, JD

Background SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. Objectives This study was: designed to determine

Design and test of ASME strainer for primary cooling system in HANARO

International Nuclear Information System (INIS)

Park, Yong-Chul; Ryu, Jeong-Soo

1999-01-01

The ASME strainers have been newly installed at the suction side of each reactor coolant pump to get rid of the foreign materials which may damage the pump impeller or interfere with the coolant path of fuel flow tube or primary plate type heat exchanger. The strainer was designed in accordance with ASME SEC. III, DIV. 1, ND and the structural integrity was verified by seismic analysis. The screen was designed in accordance with the effective void area from the result of flow analysis for T-type strainer. After installation of the strainer, it was confirmed through the field test that the flow characteristics of primary cooling system were not adversely affected. The pressure loss coefficient was calculated by Darcy equation using the pressure difference through each strainer and the flow rate measured during the strainer performance test. And these are useful data to predict flow variations by the pressure difference. (author)

Art of reading a journal article: Methodically and effectively

Science.gov (United States)

Subramanyam, RV

2013-01-01

Background: Reading scientific literature is mandatory for researchers and clinicians. With an overflow of medical and dental journals, it is essential to develop a method to choose and read the right articles. Objective: To outline a logical and orderly approach to reading a scientific manuscript. By breaking down the task into smaller, step-by-step components, one should be able to attain the skills to read a scientific article with ease. Methods: The reader should begin by reading the title, abstract and conclusions first. If a decision is made to read the entire article, the key elements of the article can be perused in a systematic manner effectively and efficiently. A cogent and organized method is presented to read articles published in scientific journals. Conclusion: One can read and appreciate a scientific manuscript if a systematic approach is followed in a simple and logical manner. PMID:23798833

When a Plant Resistance Inducer Leaves the Lab for the Field: Integrating ASM into Routine Apple Protection Practices.

Science.gov (United States)

Marolleau, Brice; Gaucher, Matthieu; Heintz, Christelle; Degrave, Alexandre; Warneys, Romain; Orain, Gilles; Lemarquand, Arnaud; Brisset, Marie-Noëlle

2017-01-01

Plant resistance inducers, also called elicitors, could be useful to reduce the use of pesticides. However, their performance in controlling diseases in the field remains unsatisfactory due to lack of specific knowledge of how they can integrate crop protection practices. In this work, we focused on apple crop and acibenzolar- S -methyl (ASM), a well-known SAR (systemic acquired resistance) inducer of numerous plant species. We provide a protocol for orchard-effective control of apple scab due to the ascomycete fungus Venturia inaequalis , by applying ASM in combination with a light integrated pest management program. Besides we pave the way for future optimization levers by demonstrating in controlled conditions (i) the high influence of apple genotypes, (ii) the ability of ASM to prime defenses in newly formed leaves, (iii) the positive effect of repeated elicitor applications, (iv) the additive effect of a thinning fruit agent.

Corticosteroid-Induced MKP-1 Represses Pro-Inflammatory Cytokine Secretion by Enhancing Activity of Tristetraprolin (TTP) in ASM Cells.

Science.gov (United States)

Prabhala, Pavan; Bunge, Kristin; Ge, Qi; Ammit, Alaina J

2016-10-01

Exaggerated cytokine secretion drives pathogenesis of a number of chronic inflammatory diseases, including asthma. Anti-inflammatory pharmacotherapies, including corticosteroids, are front-line therapies and although they have proven clinical utility, the molecular mechanisms responsible for their actions are not fully understood. The corticosteroid-inducible gene, mitogen-activated protein kinase (MAPK) phosphatase 1 (MKP-1, DUSP1) has emerged as a key molecule responsible for the repressive effects of steroids. MKP-1 is known to deactivate p38 MAPK phosphorylation and can control the expression and activity of the mRNA destabilizing protein-tristetraprolin (TTP). But whether corticosteroid-induced MKP-1 acts via p38 MAPK-mediated modulation of TTP function in a pivotal airway cell type, airway smooth muscle (ASM), was unknown. While pretreatment of ASM cells with the corticosteroid dexamethasone (preventative protocol) is known to reduce ASM synthetic function in vitro, the impact of adding dexamethasone after stimulation (therapeutic protocol) had not been explored. Whether dexamethasone modulates TTP in a p38 MAPK-dependent manner in this cell type was also unknown. We address this herein and utilize an in vitro model of asthmatic inflammation where ASM cells were stimulated with the pro-asthmatic cytokine tumor necrosis factor (TNF) and the impact of adding dexamethasone 1 h after stimulation assessed. IL-6 mRNA expression and protein secretion was significantly repressed by dexamethasone acting in a temporally distinct manner to increase MKP-1, deactivate p38 MAPK, and modulate TTP phosphorylation status. In this way, dexamethasone-induced MKP-1 acts via p38 MAPK to switch on the mRNA destabilizing function of TTP to repress pro-inflammatory cytokine secretion from ASM cells. J. Cell. Physiol. 231: 2153-2158, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

NARCIS (Netherlands)

Luger, T.; van Leent, E. J.; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A. C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; van der Valk, P. G.; Bos, J. D.

2001-01-01

SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy

Determination of the optimal method for the field-in-field technique in breast tangential radiotherapy

International Nuclear Information System (INIS)

Tanaka, Hidekazu; Hayashi, Shinya; Hoshi, Hiroaki

2014-01-01

Several studies have reported the usefulness of the field-in-field (FIF) technique in breast radiotherapy. However, the methods for the FIF technique used in these studies vary. These methods were classified into three categories. We simulated a radiotherapy plan with each method and analyzed the outcomes. In the first method, a pair of subfields was added to each main field: the single pair of subfields method (SSM). In the second method, three pairs of subfields were added to each main field: the multiple pairs of subfields method (MSM). In the third method, subfields were alternately added: the alternate subfields method (ASM). A total of 51 patients were enrolled in this study. The maximum dose to the planning target volume (PTV) (Dmax) and the volumes of the PTV receiving 100% of the prescription dose (V100%) were calculated. The thickness of the breast between the chest wall and skin surface was measured, and patients were divided into two groups according to the median. In the overall series, the average V100% with ASM (60.3%) was significantly higher than with SSM (52.6%) and MSM (48.7%). In the thin breast group as well, the average V100% with ASM (57.3%) and SSM (54.2%) was significantly higher than that with MSM (43.3%). In the thick breast group, the average V100% with ASM (63.4%) was significantly higher than that with SSM (51.0%) and MSM (54.4%). ASM resulted in better dose distribution, regardless of the breast size. Moreover, planning for ASM required a relatively short time. ASM was considered the most preferred method. (author)

Conversion rates of abstracts presented at the Urological Society of Australia and New Zealand (USANZ) Annual Scientific Meeting into full-text journal articles.

Science.gov (United States)

Yoon, Peter D; Chalasani, Venu; Woo, Henry H

2012-08-01

What's known on the subject? and What does the study add? It is well known that the transition of a presented abstract in a scientific meeting to a journal article improves the quality of the meeting and prevents an abstract being incorporated into meta-analyses or practice guidelines without proper appraisal. This is the first analysis of USANZ Annual Scientific Meeting abstracts' conversion to full publication. With relatively low publication rates compared to other international meetings, this review identifies the need for mechanisms to encourage USANZ researchers to convert their abstracts into published articles. The numbers and characteristics of the abstracts presented at the Annual Scientific Meetings (ASM) of the Urological Society of Australia and New Zealand (USANZ) that are converted to peer-reviewed publications have not previously been analysed and published. We undertook a review of all abstracts presented at the USANZ ASM from 2005 to 2009. A PubMed search was performed between 15 June and 15 July 2012, using a search algorithm to identify the full-text publications of the presented abstracts. Correlation between abstract characteristics and publication rate was then examined to distinguish the predictors for publications. Of 614 abstracts that were presented at USANZ ASM between 2005 and 2009, 183 papers were published, giving a publication rate of 29.80%. The papers were predominantly published in urological journals and were more likely to be published if they were presented by an international author or were retrospective studies or if basic science research. The mean (SD) time to publication was 14.46 (13.89) months and the mean Impact Factor of journals where papers were published was 2.90. The overall publication rate was relatively low compared with other urological meetings held in America and Europe. USANZ has a challenge of encouraging higher-quality research from the authors to further enhance its publication rate and consequently the

Parametric study of emerging high power accelerator applications using Accelerator Systems Model (ASM)

International Nuclear Information System (INIS)

Berwald, D.H.; Mendelsohn, S.S.; Myers, T.J.; Paulson, C.C.; Peacock, M.A.; Piaszczyk, CM.; Rathke, J.W.; Piechowiak, E.M.

1996-01-01

Emerging applications for high power rf linacs include fusion materials testing, generation of intense spallation neutrons for neutron physics and materials studies, production of nuclear materials and destruction of nuclear waste. Each requires the selection of an optimal configuration and operating parameters for its accelerator, rf power system and other supporting subsystems. Because of the high cost associated with these facilities, economic considerations become paramount, dictating a full evaluation of the electrical and rf performance, system reliability/availability, and capital, operating, and life cycle costs. The Accelerator Systems Model (ASM), expanded and modified by Northrop Grumman during 1993-96, provides a unique capability for detailed layout and evaluation of a wide variety of normal and superconducting accelerator and rf power configurations. This paper will discuss the current capabilities of ASM, including the available models and data base, and types of trade studies that can be performed for the above applications. (author)

Scope and implementation of standards ASME N510 / N511 in air treatment system (HVAC) of the Asco nuclear power plant; Alcance e implementacion de las normas ASME N511 en el sistema de tratamiento de aire (HVAC) de la central nuclear de Asco

Energy Technology Data Exchange (ETDEWEB)

Jaimot Jimenez, J. J.

2013-07-01

With the ITC for renewal of license units 1 and 2 of Asco, the CSN It required the commissioning tests underway in the air, according to ASME N510 filter units. It is required that, for safety-related units, to undertake preventive inspections according to ASME N511. All these requirements, in tight deadlines, have represented a great challenge for the organizations of maintenance and engineering of ANAV.

Technical report on comparative analysis of ASME QA requirements and ISO series

International Nuclear Information System (INIS)

Kim, Kwan Hyun

2000-06-01

This technical report provides the differences on the QA requirement ASME and ISO in nuclear fields. This report applies to the quality assurance(QA) programmes of the design of two requirement. The organization having overall responsibility for the nuclear design, preservation, fabrication shall be described in this report in each stage of design project

Impact of ACI-ASME code on design and construction of nuclear containment structures

International Nuclear Information System (INIS)

Reedy, R.F.

1978-01-01

The effect of the ACI-ASME code for design and construction of concrete containment structures on the nuclear and concrete industries is examined. Topics covered include purpose of the code, general requirements, responsibilities and duties, design and construction specifications, quality assurance, inspection, the liner, and stamping

Enactment of KEPIC MNH Based on 2007 ASME BPVC Section III Division 1, Subsection NH: Class 1 Components in Elevated Temperature Service

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Kim, J. B.; Lee, H. Y.; Park, C. G.

2008-11-01

This report is a draft of an enactment of KEPIC MNH based on 2007 ASME Boiler and Pressure Vessel Code, Section III, Division 1 Subsection NH for Class 1 Components in Elevated Temperature Service and contains of ASME Article NH-3000 design, the mandatory appendix I-14, and non-mandatory appendices T and X

Enactment of KEPIC MNH Based on 2007 ASME BPVC Section III Division 1, Subsection NH: Class 1 Components in Elevated Temperature Service

Energy Technology Data Exchange (ETDEWEB)

Koo, Gyeong Hoi; Kim, J. B.; Lee, H. Y.; Park, C. G

2008-11-15

This report is a draft of an enactment of KEPIC MNH based on 2007 ASME Boiler and Pressure Vessel Code, Section III, Division 1 Subsection NH for Class 1 Components in Elevated Temperature Service and contains of ASME Article NH-3000 design, the mandatory appendix I-14, and non-mandatory appendices T and X.

Development of Rotor Diagnosis Method via Motor Current Signature Analysis

Energy Technology Data Exchange (ETDEWEB)

Park, Jin Seok; Huh, Hyung; Kim, Min Hwan; Jeong, Kyeong Hoon; Lee, Gyu Mhan; Park, Jin Ho; Park, Keun Bae; Lee, Cheol Kwon; Hur, S

2006-01-15

A study on motor current signature analysis has been performed to monitor a journal bearing fault due to increasing clearance. It was known that the journal bearing clearance produces side band frequencies, the supplied current frequency plus and minus rotational rotor frequency in motor current. But the existence information of the side band frequencies is not sufficient to diagnose whether the journal bearing is safe or not. Four journal bearing sets with different clearances are used to measure the side band frequency amplitude and the rotor vibration amplitude versus the journal bearing clearance. The side band frequency amplitude and the rotor vibration amplitude are increased as the journal bearing clearance is increasing. This trend assures that ASME OM vibration guide line can be applied to estimate the journal bearing clearance size. In this research, 2.5 times the reference side band amplitude is suggested as an indicator of a journal bearing fault. Further study is necessary to make out more specific quantitative relations between the side band frequency amplitude and the journal bearing clearance of a motor.

Development of Rotor Diagnosis Method via Motor Current Signature Analysis

International Nuclear Information System (INIS)

Park, Jin Seok; Huh, Hyung; Kim, Min Hwan; Jeong, Kyeong Hoon; Lee, Gyu Mhan; Park, Jin Ho; Park, Keun Bae; Lee, Cheol Kwon; Hur, S.

2006-01-01

A study on motor current signature analysis has been performed to monitor a journal bearing fault due to increasing clearance. It was known that the journal bearing clearance produces side band frequencies, the supplied current frequency plus and minus rotational rotor frequency in motor current. But the existence information of the side band frequencies is not sufficient to diagnose whether the journal bearing is safe or not. Four journal bearing sets with different clearances are used to measure the side band frequency amplitude and the rotor vibration amplitude versus the journal bearing clearance. The side band frequency amplitude and the rotor vibration amplitude are increased as the journal bearing clearance is increasing. This trend assures that ASME OM vibration guide line can be applied to estimate the journal bearing clearance size. In this research, 2.5 times the reference side band amplitude is suggested as an indicator of a journal bearing fault. Further study is necessary to make out more specific quantitative relations between the side band frequency amplitude and the journal bearing clearance of a motor

Precipitation-hardening stainless steel bars, shapes, and forgings (ASME SA-564 with additional requirements)

International Nuclear Information System (INIS)

1975-05-01

A standard prescribing requirements for precipitation-hardening stainless steel bars, shapes, and forgings (ASME SA-564 with additional requirements) for nuclear and associated applications is presented. This standard supersedes RDT M 7-6T, dated January 1974. (U.S.)

Application of the ASME-code-case N 47 to a typical thickwalled HTR-component made of Incoloy 800

International Nuclear Information System (INIS)

Kemter, F.; Schmidt, A.

Several components of the HTR-plant are exposed to temperatures beyond 500 0 C, i.e. within the high-temperature range. The service life of those components is not only limited by fatigue damage but also mainly by creep damage and accumulated inelastic strain. These can be conservatively estimated according to the ASME-Code (high temperature part CC N47) by means of the results of elastic calculations, yet this simplified method to provide evidence often leads to calculated overloads such as the present case of the live steam collector of the steam generator of a HTR. For providing the evidence that the actual loads of the component are within permissible limits, comprehensive inelastic analyses have to be referred to in such a case. The two-dimensional inelastic analysis which is reported here in detail shows that the creep and fatigue failure as well as the inelastic extensions of the live steam collectors accumulated during the service time are below the permissible limit stated in the ASME-Code and failure of those components while used in the reactor can this be excluded. (orig.) [de

Inelasticity and the ASME code

International Nuclear Information System (INIS)

Berman, I.

1978-01-01

Although it may have more general applicability, this paper is specifically concerned with some aspects of plasticity for class I nuclear components that are contained in section III of the ASME Boiler and Pressure Vessel Code. It directly addresses design for components at temperatures at which creep is not a factor. A review is made of the relationship of plasticity to each of the three failure modes that the stress limits are intended to prevent. It is found that the prevention of bursting and gross distortion from a single application of pressure and the prevention of fatigue failure caused by repeated cycles of peak stresses are well supported by experimental results. The experimental verification for the rules to show that the primary plus secondary stresses shakedown to elastic behavior is not clear. Various directed efforts which could lead to greater assurance of shakedown to elastic behavior are suggested. The major approach should be a massive program to develop a test matrix of experimental information for various portions of each component of interest in the Code. (Auth.)

Symbolic manipulation methods in general relativity and fluid mechanics

International Nuclear Information System (INIS)

Cohen, I.

1976-03-01

Algebraic manipulation by computer, or automatic symbol manipulation (ASM) has not been used much in theoretical physics, especially if one compares it with numerical methods. Three examples of the use of ASM as a tool in theoretical physics are discussed. (Auth.)

Methods for Computing Accurate Atomic Spin Moments for Collinear and Noncollinear Magnetism in Periodic and Nonperiodic Materials.

Science.gov (United States)

Manz, Thomas A; Sholl, David S

2011-12-13

The partitioning of electron spin density among atoms in a material gives atomic spin moments (ASMs), which are important for understanding magnetic properties. We compare ASMs computed using different population analysis methods and introduce a method for computing density derived electrostatic and chemical (DDEC) ASMs. Bader and DDEC ASMs can be computed for periodic and nonperiodic materials with either collinear or noncollinear magnetism, while natural population analysis (NPA) ASMs can be computed for nonperiodic materials with collinear magnetism. Our results show Bader, DDEC, and (where applicable) NPA methods give similar ASMs, but different net atomic charges. Because they are optimized to reproduce both the magnetic field and the chemical states of atoms in a material, DDEC ASMs are especially suitable for constructing interaction potentials for atomistic simulations. We describe the computation of accurate ASMs for (a) a variety of systems using collinear and noncollinear spin DFT, (b) highly correlated materials (e.g., magnetite) using DFT+U, and (c) various spin states of ozone using coupled cluster expansions. The computed ASMs are in good agreement with available experimental results for a variety of periodic and nonperiodic materials. Examples considered include the antiferromagnetic metal organic framework Cu3(BTC)2, several ozone spin states, mono- and binuclear transition metal complexes, ferri- and ferro-magnetic solids (e.g., Fe3O4, Fe3Si), and simple molecular systems. We briefly discuss the theory of exchange-correlation functionals for studying noncollinear magnetism. A method for finding the ground state of systems with highly noncollinear magnetism is introduced. We use these methods to study the spin-orbit coupling potential energy surface of the single molecule magnet Fe4C40H52N4O12, which has highly noncollinear magnetism, and find that it contains unusual features that give a new interpretation to experimental data.

Development and application of proposed ASME Section XI Code changes for risk-based inspection of piping

International Nuclear Information System (INIS)

West, R.A.

1996-01-01

This synopsis has been written to describe a perspective on the development and application of ASME Section XI Code changes for risk-based inspection of piping. The content is specifically related to the use of risk-based technology for Inservice Inspection (ISI) of piping and efforts made to support the ASME Research/Westinghouse Owners Group/Millstone Unit 3 approach for use of this technology. The opinions contained herein may or may not reflect those of the ASME Codes and Standards Committees responsible for these activities. In order to take such a detailed technical subject and put it into an understandable format, the author has chosen to provide an analogy to simplify what is actually taking place. Risk-based technology in the ISI of piping can be likened to the process of making and using specifically ground prescription glasses to allow for better vision. It provides a process to develop and use these uniquely ground glasses that will dynamically focus on all the locations and obstacles within a plant's piping systems that could cause that plant to trip and fall; more importantly it identifies the locations where the fall could possibly hurt someone else. In this way, Nuclear Safety is being addressed

Elastic-plastic stress analysis and ASME code evaluation of a bottomhead penetration in a reactor pressure vessel

International Nuclear Information System (INIS)

Ranganath, S.

1979-01-01

Nuclear pressure vessel components are designed to meet the requirements of Section III of the ASME Boiler and Pressure Vessel Code. Specifically, the design must satisfy the limits on stress range and fatigue usage prescribed in NB-3200, Section III ASME Code for the various design and operating conditions for the component. The Code requirements assure that the component does not experience gross yielding and that in general, elastic shakedown occurs following cyclic loading. When elastic stress analysis is performed this can be shown by meeting the limits in the Code on Primary and Primary plus Secondary (P+Q) stress intensities. However, when the P+Q limits cannot be met and elastic Shakedown cannot be demonstrated, plastic analysis may be performed to meet the requirements of the Code. This paper describes the elastic-plastic stress analysis of a Boiling Water Reactor Vessel bottom head in-core penetration and illustrates how plastic analysis can be used in ASME Code evaluations to show Code compliance. Details of the thermal analysis, elastic-plastic stress analysis and fatigue evaluation are presented and it is shown that the in-core penetration satisfies the code requirements. 6 refs

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Crecy, F. de; Brun, B.

1993-01-01

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs

The adjoint sensitivity method. A contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Brun, B.

1993-01-01

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs

The adjoint sensitivity method. A contribution to the code uncertainty evaluation

Energy Technology Data Exchange (ETDEWEB)

Ounsy, A; Brun, B

1994-12-31

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs.

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

Energy Technology Data Exchange (ETDEWEB)

Ounsy, A; Crecy, F de; Brun, B

1994-12-31

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs.

ASTM and ASME-BPE Standards--Complying with the Needs of the Pharmaceutical Industry.

Science.gov (United States)

Huitt, William M

2011-01-01

Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and standards and then modifying them in order to meet the more stringent requirements of the Food and Drug Administration (FDA). In 1997 the American Society of Mechanical Engineers (ASME) published the first Bioprocessing Equipment (BPE) Standard. Through harmonization efforts this relatively new standard has brought together, scrutinized, and refined industry accepted methodologies together with FDA compliance requirements, and has established an American National Standard that provides a comprehensive set of standards that are integral to the pharmaceutical industry. This article describes various American National Standards, including those developed and published by the American Society for Testing and Materials (ASTM), and how they apply to the pharmaceutical industry. It goes on to discuss the harmonization effort that takes place between the various standards developers in an attempt to prevent conflicts and omissions between the many standards. Also included are examples of tables and figures taken from the ASME-BPE Standard. These examples provide the reader with insight to the relevant content of the ASME-BPE Standard. Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and

Conservation Methods of Endangered Species | Gundu | Journal of ...

African Journals Online (AJOL)

Journal of Research in Forestry, Wildlife and Environment. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 6, No 2 (2014) >. Log in or Register to get access to full text downloads.

Prediction of surface cracks from thick-walled pressurized vessels with ASME code

International Nuclear Information System (INIS)

Thieme, W.

1983-01-01

The ASME-Code, Section XI, Appendix A 'Analysis of flow indications' is still non-mandatory for the pressure components of nuclear power plants. It is certainly difficult to take realistic account of the many factors influencing crack propagation while making life predictions. The accuracy of the US guideline is analysed, and its possible applications are roughly outlined. (orig./IHOE) [de

The statistical background to proposed ASME/MPC fracture toughness reference curves

International Nuclear Information System (INIS)

Oldfield, W.

1981-01-01

The ASME Pressure Vessel Codes define, in Sec. 11, lower bound fracture toughness curves. These curves are used to predict the lower bound fracture toughness on the basis of the RT test procedure. This test is used to remove heat to heat differences, by permitting the lower bound (reference) curve to be moved along the temperature scale according to the measured RT. Numerous objections have been raised to the procedure, and a Subcommittee (the ASME/MPC Working Group on Reference Toughness) is currently revising the codified procedures for fracture toughness prediction. The task has required a substantial amount of statistical work, since the new procedure are to have a statistical basis. Using initiation fracture toughness (J-Integral R curve procedures in the ductile domain) it was shown that when CVN energy data is properly transformed it is highly correlated with valid fracture toughness measurements. A single functional relationship can be used to predict the mean fracture toughness for a sample of steel from a set of CVN energy measurements, and the coefficients of the function tabulated. More importantly, the approximate lower statistical bounds to the initiation fracture toughness behaviour can be similarly predicted, and coefficients for selected bounds have also been tabulated. (orig.)

Methods for the Compilation of a Core List of Journals in Toxicology.

Science.gov (United States)

Kuch, T. D. C.

Previously reported methods for the compilation of core lists of journals in multidisciplinary areas are first examined, with toxicology used as an example of such an area. Three approaches to the compilation of a core list of journals in toxicology were undertaken and the results analyzed with the aid of models. Analysis of the results of the…

Hearsay Ethnography: Conversational Journals as a Method for Studying Culture in Action.

Science.gov (United States)

Watkins, Susan Cotts; Swidler, Ann

2009-04-01

Social scientists have long struggled to develop methods adequate to their theoretical understanding of meaning as collective and dynamic. While culture is widely understood as an emergent property of collectivities, the methods we use keep pulling us back towards interview-situated accounts and an image of culture as located in individual experience. Scholars who seek to access supra-individual semiotic structures by studying public rituals and other collectively-produced texts then have difficulty capturing the dynamic processes through which such meanings are created and changed in situ. To try to capture more effectively the way meaning is produced and re-produced in everyday life, we focus here on conversational interactions-the voices and actions that constitute the relational space among actors. Conversational journals provide us with a method: the analysis of texts produced by cultural insiders who keep journals of who-said-what-to-whom in conversations they overhear or events they participate in during the course of their daily lives. We describe the method, distinguishing it from other approaches and noting its drawbacks. We then illustrate the methodological advantages of conversational journals with examples from our texts. We end with a discussion of the method's potential in our setting as well as in other places and times.

Comparative studies on the effects of a yucca extract and acibenzolar-S-methyl (ASM) on inhibition of Venturia inaequalis in apple leaves

DEFF Research Database (Denmark)

Bengtsson, Marianne Vibeke; Wulff, Ednar Gadelha; Jørgensen, Hans Jørgen Lyngs

2009-01-01

The effect of an extract of Yucca schidigera on the control and infection process of the apple scab pathogen, Venturia inaequalis, was examined and compared with the chemical resistance inducer, acibenzolar-S-methyl (ASM). In seedling assays, both materials significantly reduced apple scab symptoms...... and pathogen sporulation on leaves and both showed similar control efficacies as the reference treatment, sulphur. Whereas yucca extract and sulphur gave significant inhibition of conidial germination in vitro, ASM did not inhibit germination. Histopathological studies of the infection process of V. inaequalis...... in apple leaves showed that the yucca extract primarily acted by inhibiting pre-penetration events and penetration itself. In contrast, the ASM treatment significantly inhibited more stages of the infection process (pre-penetration, penetration and post-penetration events). These observations suggest...

Probabilistic evaluation of design S-N curve and reliability assessment of ASME code-based evaluation

International Nuclear Information System (INIS)

Zhao Yongxiang

1999-01-01

A probabilistic evaluating approach of design S-N curve and a reliability assessment approach of the ASME code-based evaluation are presented on the basis of Langer S-N model-based P-S-N curves. The P-S-N curves are estimated by a so-called general maximum likelihood method. This method can be applied to deal with the virtual stress amplitude-crack initial life data which have a characteristics of double random variables. Investigation of a set of the virtual stress amplitude-crack initial life (S-N) data of 1Cr18Ni9Ti austenitic stainless steel-welded joint reveals that the P-S-N curves can give a good prediction of scatter regularity of the S-N data. Probabilistic evaluation of the design S-N curve with 0.9999 survival probability has considered various uncertainties, besides of the scatter of the S-N data, to an appropriate extent. The ASME code-based evaluation with 20 reduction factor on the mean life is much more conservative than that with 2 reduction factor on the stress amplitude. Evaluation of the latter in 666.61 MPa virtual stress amplitude is equivalent to 0.999522 survival probability and in 2092.18 MPa virtual stress amplitude equivalent to 0.9999999995 survival probability. This means that the evaluation in the low loading level may be non-conservative and in contrast, too conservative in the high loading level. Cause is that the reduction factors are constants and the factors can not take into account the general observation that scatter of the N data increases with the loading level decreasing. This has indicated that it is necessary to apply the probabilistic approach to the evaluation of design S-N curve

Alteraciones espirométricas en pacientes asmáticos del municipio Majibacoa, 2009-2013

Directory of Open Access Journals (Sweden)

Mailin Molina Leyva

2014-08-01

Full Text Available Se realizó un estudio descriptivo, con el objetivo de identificar alteraciones espirométricas en pacientes asmáticos del municipio Majibacoa, en el período comprendido desde enero del 2009 a enero del 2013. La muestra se integró por cincuenta pacientes asmáticos con más de 20 años de evolución de la enfermedad. Se les realizó previo consentimiento informado y una prueba espirométrica. Predominó el sexo femenino y las edades comprendidas entre 35 y 54 años. Prevalecieron los pacientes en la categoría de asma persistente severa. El volumen espiratorio forzado del primer segundo se comportó patológico en el mayor por ciento de los pacientes y la capacidad vital forzada mostró alteración en un menor número de pacientes. El patrón espirométrico obstructivo fue el más frecuente en los pacientes estudiados

Long periodicity of Blazar with RXTE ASM, TA and HEGRA

OpenAIRE

Osone, S.; Teshima, M.

2002-01-01

Long periodicity for Mkn501 during a large flare in 1997 have been reported by TA, HEGRA group. Here, we establish this periodicity with archival data of RXTE All Sky Monitor(ASM), Telescope Array(TA) and HEGRA with a chance probability less than $10^{-5}$. We also find that an origin of 23 day periodicity is related with a change of either a gamma factor of electrons $\\gamma$ or the magnetic field or a beaming factor. And, in order to search for a category which have a long periodicity, we m...

Comparison of Fatigue crack growth rate of Type 347 stainless steel with ASME and JSME models

Energy Technology Data Exchange (ETDEWEB)

Hong, Seokmin; Min, Ki-Deuk; Jeon, Soon-Hyeok; Lee, Bong-Sang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study, the FCGR of 347SS was evaluated in modified PWR high temperature water conditions. The FCGRs of 347SS under modified pressurized-water conditions were measured by using compact-tension (CT) specimens at different levels of dissolved oxygen (DO), and it were compared with other models proposed by ASME and Japanese groups. Corrosion fatigue is main factor of environmental fatigue effect. Increase of DO level in water induced more corrosion damage, and it accelerated FCGR in PWR and FCGR of 347SS in PWR water condition was faster than reference curves in J-PWR and ASME draft code case derived by 304 and 316 stainless steel, but it was slower than J-BWR reference curve. Using J-BWR model for estimating the FCGR of 347SS under PWR might be conservative.

Doxofylline does not increase formoterol-induced cAMP nor MKP-1 expression in ASM cells resulting in lack of anti-inflammatory effect.

Science.gov (United States)

Patel, Brijeshkumar S; Kugel, Michael J; Baehring, Gina; Ammit, Alaina J

2017-08-01

The xanthine doxofylline has been examined in clinical trials and shown to have efficacy and greater tolerability than theophylline in asthma and chronic obstructive pulmonary disease. The 'novofylline' doxofylline has demonstrated bronchodilatory and anti-inflammatory actions in in vivo and ex vivo experimental models of respiratory disease. However, there are limited studies in vitro. We address this herein and examine whether doxofylline has anti-inflammatory impact on primary cultures of airway smooth muscle (ASM) cells. We conduct a series of investigations comparing and contrasting doxofylline with the archetypal xanthine, theophylline, and the specific phosphodiesterase (PDE) 4 inhibitor, cilomilast. We confirm that the xanthine drugs do not have action as PDE inhibitors in ASM cells. Unlike cilomilast, doxofylline (and theophylline) do not increase cAMP production in ASM cells induced by long-acting β 2 -agonist formoterol. Similar to theophylline, and consistent with the lack of cAMP potentiation, doxofylline does not augment formoterol-induced upregulation of the anti-inflammatory protein mitogen-activated protein kinase phosphatase 1 (MKP-1). However, when we examine the effect of doxofylline on secretion of the interleukin 8 from ASM cells stimulated by tumour necrosis factor (an in vitro surrogate measure of inflammation), there was no repression of inflammation. This is in contrast to the anti-inflammatory impact exerted by theophylline and cilomilast in confirmatory experiments. In summary, our study is the first to examine the effect of doxofylline on ASM cells in vitro and highlights some distinct differences between two key members of xanthine drug family, doxofylline and theophylline. Copyright © 2017 Elsevier Ltd. All rights reserved.

Arbitral action and preventive methods against predatory journal practice

Directory of Open Access Journals (Sweden)

Sung Pil Park

2018-02-01

Full Text Available As open access model of journal publication increases, predatory journals, which deceive scholars to publish journals in fake database websites and exploit them for publishing fee, is also increasing. There are two types of predatory journals. First, journal hijacking and cybersquatting generally create fake database website by mimicking authentic database website, thereby defrauding scholars for publication fee. Second, journal phishing use scam emails to steal scholars’ personal information. If scholars suffered damage from predatory journals, scholars can take either arbitral or judicial actions. Arbitral action follows arbitrational resolution process termed Uniform Domain-Name Dispute-Resolution Policy. Scholars can join Uniform Domain-Name Dispute-Resolution Policy proceeding with legal entity that has right to authentic database website, which will result in cancellation or transfer of fake database website. In contrast, scholars can take judicial action under Anticybersquatting Consumer Protection Act, which may help scholars to recover an actual monetary damage from predatory journals. Nonetheless, taking precaution to avoid predatory journals is the best course of action, rather than going through arduous cure procedures. Scholars may prevent predatory journals by carefully examining fake database website names or email addresses, or observing unreasonable number of published article issues in predatory journal websites.

Comparative study of design of piping supports class 1, 2 and 3 considering german code KTA and ASME III - NF

International Nuclear Information System (INIS)

Faloppa, Altair A.; Fainer, Gerson; Mattar Neto, Miguel; Elias, Marcos V.

2013-01-01

The objective of this paper is developing a comparative study of the design criteria for class 1, 2, 3 piping supports considering the American Code ASME Section III - NF and the German Code KTA 3205.1 to the Primary Circuit, KTA 3205.2 to the others systems and KTA 3205.3 series-production standards supports of a PWR nuclear power plant. An additional purpose of the paper is a general analysis of the main design concepts of the American Code ASME Boiler and Pressure Vessel Code, Section III, Division 1 and German Nuclear Design Code KTA that was performed in order to aid the comparative study proposed. The relevance of this study is to show the differences between codes ASME and KTA since they were applied in the design of the Nuclear Power Plants Angra 1 and Angra 2, and to the design of Angra 3, which is at the moment under construction. It is also considered their use in the design of nuclear installations such as RMB - Reator MultiProposito Brasileiro and LABGENE - Laboratorio de Geracao Nucleoeletrica. (author)

TRAIL death receptor 4 signaling via lysosome fusion and membrane raft clustering in coronary arterial endothelial cells: evidence from ASM knockout mice.

Science.gov (United States)

Li, Xiang; Han, Wei-Qing; Boini, Krishna M; Xia, Min; Zhang, Yang; Li, Pin-Lan

2013-01-01

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and its receptor, death receptor 4 (DR4), have been implicated in the development of endothelial dysfunction and atherosclerosis. However, the signaling mechanism mediating DR4 activation leading to endothelial injury remains unclear. We recently demonstrated that ceramide production via hydrolysis of membrane sphingomyelin by acid sphingomyelinase (ASM) results in membrane raft (MR) clustering and the formation of important redox signaling platforms, which play a crucial role in amplifying redox signaling in endothelial cells leading to endothelial dysfunction. The present study aims to investigate whether TRAIL triggers MR clustering via lysosome fusion and ASM activation, thereby conducting transmembrane redox signaling and changing endothelial function. Using confocal microscopy, we found that TRAIL induced MR clustering and co-localized with DR4 in coronary arterial endothelial cells (CAECs) isolated from wild-type (Smpd1 (+/+)) mice. Furthermore, TRAIL triggered ASM translocation, ceramide production, and NADPH oxidase aggregation in MR clusters in Smpd1 ( +/+ ) CAECs, whereas these observations were not found in Smpd1 (-/-) CAECs. Moreover, ASM deficiency reduced TRAIL-induced O(2) (-[Symbol: see text]) production in CAECs and abolished TRAIL-induced impairment on endothelium-dependent vasodilation in small resistance arteries. By measuring fluorescence resonance energy transfer, we found that Lamp-1 (lysosome membrane marker protein) and ganglioside G(M1) (MR marker) were trafficking together in Smpd1 (+/+) CAECs, which was absent in Smpd1 (-/-) CAECs. Consistently, fluorescence imaging of living cells with specific lysosome probes demonstrated that TRAIL-induced lysosome fusion with membrane was also absent in Smpd1 (-/-) CAECs. Taken together, these results suggest that ASM is essential for TRAIL-induced lysosomal trafficking, membrane fusion and formation of MR redox signaling platforms

Assessment of ASME code examinations on regenerative, letdown and residual heat removal heat exchangers

International Nuclear Information System (INIS)

Gosselin, Stephen R.; Cumblidge, Stephen E.; Anderson, Michael T.; Simonen, Fredric A.; Tinsley, G A.; Lydell, B.; Doctor, Steven R.

2005-01-01

Inservice inspection requirements for pressure retaining welds in the regenerative, letdown, and residual heat removal heat exchangers are prescribed in Section XI Articles IWB and IWC of the ASME Boiler and Pressure Vessel Code. Accordingly, volumetric and/or surface examinations are performed on heat exchanger shell, head, nozzle-to-head, and nozzle-to-shell welds. Inspection difficulties associated with the implementation of these Code-required examinations have forced operating nuclear power plants to seek relief from the U.S. Nuclear Regulatory Commission. The nature of these relief requests are generally concerned with metallurgical, geometry, accessibility, and radiation burden. Over 60% of licensee requests to the NRC identify significant radiation exposure burden as the principle reason for relief from the ASME Code examinations on regenerative heat exchangers. For the residual heat removal heat exchangers, 90% of the relief requests are associated with geometry and accessibility concerns. Pacific Northwest National Laboratory was funded by the NRC Office of Nuclear Regulatory Research to review current practice with regard to volumetric and/or surface examinations of shell welds of letdown heat exchangers regenerative heat exchangers and residual (decay) heat removal heat exchangers Design, operating, common preventative maintenance practices, and potential degradation mechanisms are reviewed. A detailed survey of domestic and international PWR-specific operating experience was performed to identify pressure boundary failures (or lack of failures) in each heat exchanger type and NSSS design. The service data survey was based on the PIPExp- database and covers PWR plants worldwide for the period 1970-2004. Finally a risk assessment of the current ASME Code inspection requirements for residual heat removal, letdown, and regenerative heat exchangers is performed. The results are then reviewed to discuss the examinations relative to plant safety and

Ranking Journals Using Social Choice Theory Methods: A Novel Approach in Bibliometrics

Energy Technology Data Exchange (ETDEWEB)

Aleskerov, F.T.; Pislyakov, V.; Subochev, A.N.

2016-07-01

We use data on economic, management and political science journals to produce quantitative estimates of (in)consistency of evaluations based on seven popular bibliometric indica (impact factor, 5-year impact factor, immediacy index, article influence score, h-index, SNIP and SJR). We propose a new approach to aggregating journal rankings: since rank aggregation is a multicriteria decision problem, ordinal ranking methods from social choice theory may solve it. We apply either a direct ranking method based on majority rule (the Copeland rule, the Markovian method) or a sorting procedure based on a tournament solution, such as the uncovered set and the minimal externally stable set. We demonstrate that aggregate rankings reduce the number of contradictions and represent the set of single-indicator-based rankings better than any of the seven rankings themselves. (Author)

A new clamp method for firing bricks | Obeng | Journal of Applied ...

African Journals Online (AJOL)

A new clamp method for firing bricks. ... Journal of Applied Science and Technology ... To overcome this operational deficiencies, a new method of firing bricks that uses brick clamp technique that incorporates a clamp wall of 60 cm thickness, a six tier approach of sealing the top of the clamp (by combination of green bricks) ...

Efecto de budesonida sobre la densidad y el metabolismo óseo en niños asmáticos

Directory of Open Access Journals (Sweden)

Paoli de Valeri Mariela

2000-01-01

Full Text Available OBJETIVO: Determinar el efecto de la administración de budesonida inhalado sobre la densidad, el contenido mineral y el metabolismo óseo en niños asmáticos. MATERIAL Y MÉTODOS: Estudio transversal realizado de septiembre de 1996 a julio de 1997, en el que se estudiaron 38 niños y niñas de entre 6 y 11 años de edad, seleccionados de la consulta externa de neumonología infantil del Instituto Autónomo Hospital Universitario de Los Andes, Mérida, Venezuela. Se constituyeron tres grupos: nueve niños asmáticos tratados con budesonida inhalado (300 µg/día en promedio durante más de seis meses, (grupo A, 14 niños asmáticos que no recibieron tratamiento esteroideo (grupo B y 15 niños no asmáticos (grupo C. A todos se les practicó una evaluación ósea con marcadores de formación y resorción y con una medición de la densidad (DMO y el contenido mineral óseo (CMO. Se calcularon medidas de tendencia central y de dispersión, se realizó análisis de varianza, y se utilizaron las pruebas de Fisher y Scheffé para comparación de medias. RESULTADOS: En los grupos estudiados (A, B y C los niveles séricos de calcio fueron 9.1±0.3; 9.6±0.4; 9.3±0.6 mg/ml; los de osteocalcina fueron 14.8±4.6; 13.0±2.5; 11.9±3.4 ng/dl; los de telopéptido carboxiterminal del colágeno tipo I (ICTP fueron 19.6±16.5; 14.2±15.4; 13.0±18.3 µg/l; la DMO fue de 0.67±0.06; 0.68±0.06; 0.69±0.06 g/cm², y el CMO fue de 1 158.8±217.4; 1 106.4±256.1; 1 176.5±240.5 g, respectivamente. No hubo diferencias significativas entre los grupos. CONCLUSIONES: La administración de budesonida inhalada en dosis de 100 a 400 µg/día por un periodo de seis meses no produce modificaciones en la densidad y en el metabolismo óseo en niños asmáticos.

Comportamiento de variables clínico-epidemiológicas en pacientes asmáticos. Consultorio Médico de Familia 14, Puerto Padre

Directory of Open Access Journals (Sweden)

José Ramón Martínez Pérez

2015-12-01

Full Text Available Se realizó un estudio descriptivo de corte transversal en 40 pacientes asmáticos de todas las edades, pertenecientes al Consultorio 14 del área de salud de Puerto Padre, provincia de Las Tunas, durante los meses de enero a junio de 2008; con el objetivo de determinar el comportamiento de variables clínico-epidemiológicas en dichos pacientes. Para cumplimentar los objetivos se diseñó una encuesta que recogió las variables de interés. El análisis se hizo a través del sistema Statistix, permitiendo  obtener  la distribución de frecuencia y los porcientos. El test de Chi-Cuadrado se empleó en la comparación de variables cualitativas. Los resultados fueron descritos, interpretados y comparados con otros estudios. Se concluye que los pacientes grado I según Kraeppelin son los mas representados en nuestra población de pacientes asmáticos;  los broncodilatadores son los medicamentos mas utilizados por la población asmática estudiada; el incumplimiento del tratamiento medicamentoso no se relacionó con la severidad de la enfermedad en la población estudiada;  las malas condiciones de la vivienda y  el tabaquismo influyeron de forma negativa en la evolución del paciente asmático.

Analysis of the ASME methodology for evaluation of erosion-corrosion defects with respect to the differences in the calculation and in materials used at the Dukovany NPP

International Nuclear Information System (INIS)

Kadecka, P.

1995-01-01

The problem of evaluation of tolerable defects and thinning of pipe walls was analyzed. In fact, a procedure for evaluation of tolerable defects is described in ASME Code Case N 480 based on the ASME ''Rules for Construction of Nuclear Power Plant Components''. The pipe systems of the Dukovany NPP, however, were constructed to different (East European) standards, and therefore caution should be exercised when applying US standards to this plant. The report demonstrates major differences between the ASME Standard and the proposed Czech standard ''A.S.I. Standards Documentation for Strength Calculations of Equipment and Piping of WWER Type Nuclear Power Plants'' developed by the Czech Association of Mechanical Engineers (A.S.I), evaluates the applicability of Code Case N 480 to the Dukovany plant, and proposes a Czech procedure for the evaluation. The basic characteristics of materials cited by ASME II and carbon steels used in the secondary circuit of the Dukovany NPP are also compared. (P.A.). 78 tabs., 2 figs., 4 refs

FY16 ASME High Temperature Code Activities

Energy Technology Data Exchange (ETDEWEB)

Swindeman, M. J. [Chromtech Inc., Oak Ridge, TN (United States); Jetter, R. I. [R. I Jetter Consulting, Pebble Beach, CA (United States); Sham, T. -L. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-09-01

One of the objectives of the ASME high temperature Code activities is to develop and validate both improvements and the basic features of Section III, Division 5, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to be used to assess whether or not a specific component under specified loading conditions will satisfy the elevated temperature design requirements for Class A components in Section III, Division 5, Subsection HB, Subpart B (HBB). There are many features and alternative paths of varying complexity in HBB. The initial focus of this task is a basic path through the various options for a single reference material, 316H stainless steel. However, the program will be structured for eventual incorporation all the features and permitted materials of HBB. Since this task has recently been initiated, this report focuses on the description of the initial path forward and an overall description of the approach to computer program development.

Draft ASME code case on ductile cast iron for transport packaging

International Nuclear Information System (INIS)

Saegusa, T.; Arai, T.; Hirose, M.; Kobayashi, T.; Tezuka, Y.; Urabe, N.; Hueggenberg, R.

2004-01-01

The current Rules for Construction of ''Containment Systems for Storage and Transport Packagings of Spent Nuclear Fuel and High Level Radioactive Material and Waste'' of Division 3 in Section III of ASME Code (2001 Edition) does not include ductile cast iron in its list of materials permitted for use. The Rules specify required fracture toughness values of ferritic steel material for nominal wall thickness 5/8 to 12 inches (16 to 305 mm). New rule for ductile cast iron for transport packaging of which wall thickness is greater than 12 inches (305mm) is required

Shared Journaling as Peer Support in Teaching Qualitative Research Methods

Science.gov (United States)

Humble, Aine M.; Sharp, Elizabeth

2012-01-01

Teaching qualitative research methods (QRM), particularly early on in one's academic career, can be challenging. This paper describes shared peer journaling as one way in which to cope with challenges such as complex debates in the field and student resistance to interpretive paradigms. Literature on teaching QRM and the pedagogical value of…

Activated sludge model (ASM) based modelling of membrane bioreactor (MBR) processes: a critical review with special regard to MBR specificities.

Science.gov (United States)

Fenu, A; Guglielmi, G; Jimenez, J; Spèrandio, M; Saroj, D; Lesjean, B; Brepols, C; Thoeye, C; Nopens, I

2010-08-01

Membrane bioreactors (MBRs) have been increasingly employed for municipal and industrial wastewater treatment in the last decade. The efforts for modelling of such wastewater treatment systems have always targeted either the biological processes (treatment quality target) as well as the various aspects of engineering (cost effective design and operation). The development of Activated Sludge Models (ASM) was an important evolution in the modelling of Conventional Activated Sludge (CAS) processes and their use is now very well established. However, although they were initially developed to describe CAS processes, they have simply been transferred and applied to MBR processes. Recent studies on MBR biological processes have reported several crucial specificities: medium to very high sludge retention times, high mixed liquor concentration, accumulation of soluble microbial products (SMP) rejected by the membrane filtration step, and high aeration rates for scouring purposes. These aspects raise the question as to what extent the ASM framework is applicable to MBR processes. Several studies highlighting some of the aforementioned issues are scattered through the literature. Hence, through a concise and structured overview of the past developments and current state-of-the-art in biological modelling of MBR, this review explores ASM-based modelling applied to MBR processes. The work aims to synthesize previous studies and differentiates between unmodified and modified applications of ASM to MBR. Particular emphasis is placed on influent fractionation, biokinetics, and soluble microbial products (SMPs)/exo-polymeric substances (EPS) modelling, and suggestions are put forward as to good modelling practice with regard to MBR modelling both for end-users and academia. A last section highlights shortcomings and future needs for improved biological modelling of MBR processes. (c) 2010 Elsevier Ltd. All rights reserved.

Ascomycin macrolactam derivative SDZ ASM 981 inhibits the release of granule-associated mediators and of newly synthesized cytokines in RBL 2H3 mast cells in an immunophilin-dependent manner.

Science.gov (United States)

Hultsch, T; Müller, K D; Meingassner, J G; Grassberger, M; Schopf, R E; Knop, J

1998-09-01

Mast cells play an important role in the pathological development of many inflammatory and allergic diseases and inhibition of mast cell activation is a potential target for therapeutic intervention. Therefore, the effect of the novel ascomycin macrolactam derivative SDZ ASM 981 on Fc epsilonRI-mediated activation of rat basophilic leukemia (RBL) cells, as a model for mast cell activation, was investigated. First, the ability to inhibit different mast cell immunophilins in vitro was tested. Using recombinant macrophilin-12 (FKBP-12), inhibition of rotamase activity with an IC50 of approximately 6 nM was observed. The rotamase activity of cyclophilin A (18 kDa) was not affected. Secondly, the effect of SDZ ASM 981 on Fc epsilonRI-mediated mast cell activation was investigated in the RBL cell model. SDZ ASM 981 inhibited exocytosis of preformed mediators (e.g. serotonin) with an IC50 of approximately 30 nM. Transcription and release of newly synthesized mediators (e.g. TNF-alpha) was inhibited with an IC50 of approximately 100 nM. The inhibitory effect of SDZ ASM 981 was antagonized by rapamycin. We conclude that SDZ ASM 981 is a potent inhibitor of Fc epsilonRI-mediated activation of mast cells in vitro. The mechanism of action involves formation of (calcineurin) inhibitory complexes with macrophilins. We suggest that this inhibitory action on mast cells might contribute to the antiinflammatory effect of SDZ ASM 981 observed in vivo (e.g. in aptopic dermatitis and psoriasis).

Methodology and guidelines for evaluation of welded attachments on ASME Class 1,2, or 3 piping

International Nuclear Information System (INIS)

Chang, K.C.; Adams, T.M.; Rodabaugh, E.C.

1985-01-01

The ASME Boiler and Pressure Vessel Code, Section III Subsection NB/NC/ND-3600 provides simplified rules for the evaluation and qualification of piping components. The use of rectangular and hollow, circular welded attachments (hereafter called lugs and trunions) is sometimes necessary in order to provide support for piping systems. The Code provides a set of simple and conservative equations, the associated stress indicies, and specified limitations on their applicability for lugs on Class 1 and Class 2/3 piping in Code Cases N-122 and N-318 respectively. Two new ASME Section III Code Cases, N-391 and N-392, have been prepared to provide the corresponding design guidelines for specific trunion configurations. This paper presents the background on the major concepts involved in the development of these Code Cases and provides some general guidelines to the analysts and designers for the qualification of the attachments not covered by the Code Cases

A superlinear iteration method for calculation of finite length journal bearing's static equilibrium position

Science.gov (United States)

Zhou, Wenjie; Wei, Xuesong; Wang, Leqin; Wu, Guangkuan

2017-05-01

Solving the static equilibrium position is one of the most important parts of dynamic coefficients calculation and further coupled calculation of rotor system. The main contribution of this study is testing the superlinear iteration convergence method-twofold secant method, for the determination of the static equilibrium position of journal bearing with finite length. Essentially, the Reynolds equation for stable motion is solved by the finite difference method and the inner pressure is obtained by the successive over-relaxation iterative method reinforced by the compound Simpson quadrature formula. The accuracy and efficiency of the twofold secant method are higher in comparison with the secant method and dichotomy. The total number of iterative steps required for the twofold secant method are about one-third of the secant method and less than one-eighth of dichotomy for the same equilibrium position. The calculations for equilibrium position and pressure distribution for different bearing length, clearance and rotating speed were done. In the results, the eccentricity presents linear inverse proportional relationship to the attitude angle. The influence of the bearing length, clearance and bearing radius on the load-carrying capacity was also investigated. The results illustrate that larger bearing length, larger radius and smaller clearance are good for the load-carrying capacity of journal bearing. The application of the twofold secant method can greatly reduce the computational time for calculation of the dynamic coefficients and dynamic characteristics of rotor-bearing system with a journal bearing of finite length.

Batse/Sax and Batse/RXTE-ASM Joint Spectral Studies of GRBs

Science.gov (United States)

Paciesas, William S.

2002-01-01

We proposed to make joint spectral analysis of gamma-ray bursts (GRBs) in the BATSE data base that are located within the fields of view of either the BeppoSAX wide field cameras (WFCs) or the RXTE all-sky monitor (ASM). The very broad-band coverage obtained in this way would facilitate various studies of GRB spectra that are difficult to perform with BATSE data alone. Unfortunately, the termination of the CGRO mission in June 2000 was not anticipated at the time of the proposal, and the sample of common events turned out to be smaller than we would have liked.

Materials and design bases issues in ASME Code Case N-47

International Nuclear Information System (INIS)

Huddleston, R.L.; Swindeman, R.W.

1993-04-01

A preliminary evaluation of the design bases (principally ASME Code Case N-47) was conducted for design and operation of reactors at elevated temperatures where the time-dependent effects of creep, creep-fatigue, and creep ratcheting are significant. Areas where Code rules or regulatory guides may be lacking or inadequate to ensure the operation over the expected life cycles for the next-generation advanced high-temperature reactor systems, with designs to be certified by the US Nuclear Regulatory Commission, have been identified as unresolved issues. Twenty-two unresolved issues were identified and brief scoping plans developed for resolving these issues

Meta-analysis as Statistical and Analytical Method of Journal's Content Scientific Evaluation.

Science.gov (United States)

Masic, Izet; Begic, Edin

2015-02-01

A meta-analysis is a statistical and analytical method which combines and synthesizes different independent studies and integrates their results into one common result. Analysis of the journals "Medical Archives", "Materia Socio Medica" and "Acta Informatica Medica", which are located in the most eminent indexed databases of the biomedical milieu. The study has retrospective and descriptive character, and included the period of the calendar year 2014. Study included six editions of all three journals (total of 18 journals). In this period was published a total of 291 articles (in the "Medical Archives" 110, "Materia Socio Medica" 97, and in "Acta Informatica Medica" 84). The largest number of articles was original articles. Small numbers have been published as professional, review articles and case reports. Clinical events were most common in the first two journals, while in the journal "Acta Informatica Medica" belonged to the field of medical informatics, as part of pre-clinical medical disciplines. Articles are usually required period of fifty to fifty nine days for review. Articles were received from four continents, mostly from Europe. The authors are most often from the territory of Bosnia and Herzegovina, then Iran, Kosovo and Macedonia. The number of articles published each year is increasing, with greater participation of authors from different continents and abroad. Clinical medical disciplines are the most common, with the broader spectrum of topics and with a growing number of original articles. Greater support of the wider scientific community is needed for further development of all three of the aforementioned journals.

Description of comprehensive pump test change to ASME OM code, subsection ISTB

International Nuclear Information System (INIS)

Hartley, R.S.

1994-01-01

The American Society of Mechanical Engineers (ASME) Operations and Maintenance (OM) Main Committee and Board on Nuclear Codes and Standards (BNCS) recently approved changes to ASME OM Code-1990, Subsection ISTB, Inservice Testing of Pumps in Light-Water Reactor Power Plants. The changes will be included in the 1994 addenda to ISTB. The changes, designated as the comprehensive pump test, incorporate a new, improved philosophy for testing safety-related pumps in nuclear power plants. An important philosophical difference between the open-quotes old codeclose quotes inservice testing (IST) requirements and these changes is that the changes concentrate on less frequent, more meaningful testing while minimizing damaging and uninformative low-flow testing. The comprehensive pump test change establishes a more involved biannual test for all pumps and significantly reduces the rigor of the quarterly test for standby pumps. The increased rigor and cost of the biannual comprehensive tests are offset by the reduced cost of testing and potential damage to the standby pumps, which comprise a large portion of the safety-related pumps at most plants. This paper provides background on the pump testing requirements, discusses potential industry benefits of the change, describes the development of the comprehensive pump test, and gives examples and reasons for many of the specific changes. This paper also describes additional changes to ISTB that will be included in the 1994 addenda that are associated with, but not part of, the comprehensive pump test

Intervención educativa para población infanto-juvenil asmática

Directory of Open Access Journals (Sweden)

Maria Antonia Acevedo Veja

2015-11-01

Full Text Available Se realizó una intervención educativa a la población infanto-juvenil asmática con edades entre ocho y once años en el policlínico de Manatí, Las Tunas, entre enero y julio de 2012, con el objetivo de evaluar la eficacia de la misma. La población de estudio estuvo formada por los 258 pacientes asmáticos de los 29 Consultorios de Médico de Familia (CMF del área, y la muestra por los 50 seleccionados por muestreo aleatorio simple. La información se obtuvo mediante un cuestionario que fue aplicado antes y después de la intervención educativa y los datos fueron recogidos durante la consulta y de la historia clínica individual. Se concluyó que predominó el sexo masculino, con antecedentes de primera línea de asma bronquial, con factores desencadenantes tales como: infecciones respiratorias agudas, polvo y humedad, así como aquellos que presentan signos clínicos de reflujo y que tienen una mala técnica de aplicación de spray. Se apreció un insuficiente nivel de conocimientos sobre la evaluación de severidad de la crisis, los factores desencadenantes, el manejo del spray y el tratamiento intercrisis, y las exacerbaciones.

ASME power test code ptc 4.1 for steam generators; Codigo de pruebas de potencia ASME ptc 4.1 para generadores de vapor

Energy Technology Data Exchange (ETDEWEB)

Plauchu Alcantara, Jorge Alberto [Plauchu Consultores, Morelia, Michoacan (Mexico)

2001-07-01

This presentation is oriented towards those who in this subject have experience in the design and equipment specification, plant projects, factory and field testing, operation or result analyses. An important fraction of the national energy supply, approximately 13%, is applied to the steam generation in the different aspects of the industrial activity, in the electrical industry of public service and in the commercial and services sector. The development of the national programs of energy efficiency verifies this when dedicating to this use of the energy important projects, some of them with support of the USAID. The measurement of the energy utilization or the efficiency of steam generators (or boilers) is made applying some procedure agreed by the parts and the one of greater acceptance and best known in Mexico and internationally is the ASME Power Test Code PTC 4.1 for Steam Generators. The purpose and formality in the determination of efficiency and of steam generation capacity behavior, thermal basic regime or fulfillment of guarantees, radically changes the exigencies of strict attachment to the PTC 4.1 This definition will determine the importance of the test method selected, the deviations and convened exceptions, the influence of the precision and the measurement errors, the consideration of auxiliary equipment, etc. An interpretation or incorrect application of the Test Code has lead and will lead to results and nonreliable decisions. [Spanish] Esta exposicion se orienta a quienes en este tema cuenta con experiencia en diseno y especificacion de equipo, proyecto de planta, pruebas en fabrica y campo, operacion o analisis de resultados. Una fraccion importante de la oferta nacional de energia, 13% aproximadamente, se aplica a la generacion de vapor en diferentes giros de actividad industrial, en la industria electrica, de servicio publico y en el sector de servicios y comercial. El desarrollo de los programas nacionales de eficiencia energetica comprueba

A Retrospective Look at 20 Years of ASM Education Programs (1990-2010) and a Prospective Look at the Next 20 Years (2011-2030).

Science.gov (United States)

Chang, Amy

2011-01-01

Professional societies provide visibility and legitimacy to the work of their post secondary educator members, advocate best practices in courses and sponsored student research, and establish deep networks and communities that catalyze members to collectively engage in undergraduate teaching and learning scholarship. Within the American Society for Microbiology (ASM), the Education Board, established in the mid-1970s, assumes this role. I have been fortunate enough to watch several pivotal programs support our growth and change the status quo by providing opportunities for biology educators to flourish. In this retrospective review, the background and details I offer about each initiative help explain ASM Education offerings, how our growth has been supported and how the status quo has changed. In this prospective look, I offer my vision of the future in post secondary education where classroom learning is student-centered and focused on global problems affecting our health and environment. For the profession to proliferate, the ASM must provide members as many opportunities in learning biology as they do with advancing biology to new frontiers.

Challenge - converting to ANSI/ASME NQA Standard 1

International Nuclear Information System (INIS)

Nansen, J.N.

1983-03-01

Prior to August, 1980, Westinghouse Hanford Company operated the Hanford Engineering Development Laboratory Quality Program in accordance with the requirements of RDT F 2-2T and RDT F 2-4T and for a short while to ANSI N45.2. Following the issuance of the national consensus standard ANSI/ ASME NQA Standard 1 in August 1979, and its acceptance by DOE, the Laboratory began making changes to meet these requirements in its internal quality program in August 1980. This was followed with the invoking of these requirements on supplier's programs and all procurement activities in March of 1981. This conversion was completed in approximately six months and provided an opportunity for several improvements. The keynote of this standard is flexibility. A major improvement noted was in the flexibility of application. The program can be tailored to meet specific needs. Vendor surveys under NQA-1 have shown positive results in that the organization and structure of the standard is much easier to follow and understand

Conversion of Traditional Journalism in the Age of Information: Data Journalism

Directory of Open Access Journals (Sweden)

Alaattin ASLAN

2016-12-01

Full Text Available The changes in technology and the emergence of information revolution as a result of these changes lead to differences in journalists’ methods of getting news. These developments in computer and internet area have affected the profession of journalism and this situation led to the emergence of concept of data journalism. Data journalism reflects a system in which open data and online reporting are used for creating the story which constitutes the essence of journalism. The changes in both news distribution environment and news consumption habits have directed news corporations and journalists to a new area. This environment is called internet – a free and unlimited source- in which unstructured data are abundantly available. In today’s environment where almost everything is expressed numerically, in other words digitized; internet has become the most significant channel for data journalism. For the data journalism to work efficiently, data should be clear, analyzable and be in a format which is proper for turning into a story. Therefore, the first task of data journalists appears as purifying data from redundancy and combining them by using multiple methods in order to create the story. This study aims to clarify and explain the concept of data journalism -a new aspect of journalismand its processes. As a research method, descriptive research model has been used in the study and data journalism examples have been evaluated. By means of this evaluation, a discussion about transforming of traditional journalism into data journalism and the effect of data journalism concept on understanding of new aspect of journalism has been conducted. As a result, conveying the news by making a story of it based on data is regarded as a new movement. Besides, making a story out of news clarifies a serious example related to the reliability of news and how open source data are conveyed to the public. It is understood well that this new understanding of

Meeting report on the ASM Conference on Mechanisms of Interbacterial Cooperation and Competition.

Science.gov (United States)

Lories, Bram; Parijs, Ilse; Foster, Kevin R; Steenackers, Hans P

2017-08-14

The ASM Conference on Mechanisms of Interbacterial Cooperation and Competition was held in Washington DC, from 1 to 4 March 2017. The conference provided an international forum for sociomicrobiologists from different disciplines to present and discuss new findings. The meeting covered a wide range of topics, spanning molecular mechanisms, ecology, evolution, computation and manipulation of interbacterial interactions, and encompassed social communities in medicine, the natural environment, and industry. This report summarizes the presentations and emerging themes. Copyright © 2017 American Society for Microbiology.

Nupack, the new ASME code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as Nupack, has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used for the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper

Aeração nasal em crianças asmáticas Nasal ventilation in asthmatics children

Directory of Open Access Journals (Sweden)

Daniele Andrade da Cunha

2011-10-01

Full Text Available OBJETIVO: identificar a presença de sinais de alterações na expiração de crianças asmáticas. MÉTODO: este estudo foi realizado com 30 crianças com idades entre 6 e 10 anos de ambos os sexos com diagnóstico clínico de asma confirmado pelo prontuário médico e 30 crianças não asmáticas também de ambos os sexos na mesma faixa etária. Foi avaliada a aeração nasal com o espelho milimetrado de Altmann, sendo mensurado o escape de ar nasal objetivando a verificação da saída uni ou bilateral do ar e a relação de simetria entre a narina direita e a esquerda. As imagens foram importadas para o computador por meio do scanner HP da série Scanjet 2400. A análise foi realizada no software Scion Image for Windows (Alpha 4.0.3.2. Para análise das variáveis quantitativas entre grupos foi aplicado o teste t-student e para a análise intragrupos foi aplicado o teste t-Student pareado.Todas as conclusões foram tomadas ao nível de significância de 5%, sendo usados o Excel 2000 e o SPSS v8.0, para as análises. RESULTADOS: não foram encontradas diferenças estatisticamente significantes entre as crianças asmáticas e não-ásmáticas, acerca das mensurações quanto à área total e quanto às áreas das narinas direita e esquerda. CONCLUSÃO: não foi identificada a presença de sinais de alterações na expiração de crianças asmáticas, desta forma, faz-se necessário um estudo mais específico das funções nasal e pulmonar.PURPOSE: to identify the symptoms of changes in the exhalation of asthmatic children. METHOD: this study was conducted with 30 children from 6 to 10 year-old, of both genders and with asthma clinical diagnosis confirmed by medical records and 30 non-asthmatic children from 6 to 10 year-old, of both genders, and with same age. We evaluated the nasal ventilation with Altmann millimeter nasal mirror measuring the nasal air escape in order to check their unilateral or bilateral air output and the relation of

Interim status report on the revision of ASME PTC 12.1 -- closed feedwater heaters

International Nuclear Information System (INIS)

Stellern, J.L.; Hoobler, J.V.; Milton, J.W.; Welch, T.; Kona, C.; Thompson, H.N.; Tsou, J.L.

1993-01-01

The ASME Performance Test Code (PTC) 12.1-1978 for the performance testing of feedwater heaters is being revised extensively and updated. The committee anticipates that the final draft of the proposed Code will be ready for industry review in 1993. This Code revision will greatly enhance the usefulness and cost effectiveness of feedwater heater performance testing. This paper has been prepared to report on the progress of the committee and to disseminate information on the nature of the revision. Included in this paper are some of the notable changes intended for the Code. The most extensive change is the calculation method, which is described in step-by-step detail. An approach is also described for using ultrasonic flow techniques to test individual or split-string feedwater heaters, when flow nozzles are not available. Additionally some educational information on the use and limitations of ultrasonic measurement instrumentation is included. Discussion is also included on the required uncertainty analysis. 3 refs., 2 figs., 2 tabs

Sex Reporting in Preclinical Microbiological and Immunological Research.

Science.gov (United States)

Potluri, Tanvi; Engle, Kyrra; Fink, Ashley L; Vom Steeg, Landon G; Klein, Sabra L

2017-11-14

Both sex (i.e., biological construct of male and female) and gender (i.e., social construct of masculine and feminine) impact the pathogenesis of diseases, including those caused by microbial infections. Following the 2015 NIH policy for consideration of sex as a biological variable in preclinical research, in 2018, authors of papers published in primary-research American Society for Microbiology (ASM) journals will be asked to report the sex of the research subjects and animals and of materials derived directly from them. To address the need for sex reporting in ASM journals, we systematically reviewed 2,928 primary-research articles published in six primary-research ASM journals ( Antimicrobial Agents and Chemotherapy , Clinical and Vaccine Immunology , Infection and Immunity , Journal of Bacteriology , Journal of Virology , and mBio ) in 2016. Approximately 37% of animal studies and 9% of primary cell culture papers published in 2016 would have been affected by the new sex-reporting policy. For animal studies (i.e., studies with any nonhuman vertebrate hosts), most published papers either did not report the sex of the animals or used only female animals, and a minority used only males or both sexes. For published studies using primary cells from diverse animal species (i.e., humans and nonhuman vertebrates), almost all studies failed to report the sex of donors from which the cells were isolated. We believe that reporting the sex of animals and even of the donors of derived cells could improve the rigor and reproducibility of research conducted in microbiology and immunology and published in ASM journals. Copyright © 2017 Potluri et al.

NRC needs and their implementation-ASME Section IX code

International Nuclear Information System (INIS)

Liaw, B.D.

1985-01-01

The guiding principle from the onset of government regulation for the peaceful use of nuclear energy has been to prescribe only the minimum requirements that are needed for safety. In the pioneer regulators' collective mind, the technical details could be left to the regulated industry through its agents like NSSS vendors and A/E's and their surrogate organizations like ASME, ANS, AIF, etc. However, it has evolved through the years, due either to the bureaucratic momentum or the vacuum in industry leadership, into a situation where one sees an ever increasing number of detailed ''requirements'' prescribed by the regulators. Within the scope of activities covered by Section XI, there is no exception: e.g., NUREG-067, -0531 -1061; NUREG-0313 Rev. 0, Rev. 1, and now Rev. 2; IE Bulletins 82-03, 83-02; and Generic Letters 84-11, and 84-07, etc. for one issue of pipe crack alone; and there are more to come. There appears a consensus among all concerned parties including regulators that this is not a desirable situation and that something must be done to reverse this trend. The purpose of this discussion is, therefore, to explore the areas where the Section XI Code can be restructured to meet this need, and to seek ideas from the representatives of the regulated industry on the methods of implementation that are effective, efficient, and acceptable to all concerned parties

Developments on ASME Code Cases to Risk-Informed Repair/Replacement Activities in Support of Risk-Informed Regulation Initiatives

International Nuclear Information System (INIS)

Balkey, Kenneth R.; Holston, William C.

2002-01-01

ASME Code Case N-658, 'Risk-Informed Safety Classification for Use in Risk-Informed Repair/Replacement Activities' and Code Case N-660, 'Alternative Repair/Replacement Requirements For Items Classified In Accordance With Risk-Informed Processes' are being completed to expand the breadth of risk-informed requirements for pressure-retaining items. This initiative, which is built from prior ASME Section XI risk-informed inservice inspection developments over the past decade, has been undertaken in conjunction with U.S. risk-informed regulation efforts. The U.S. Nuclear Regulatory Commission (NRC) is working with the industry on risk informing Title 10 Code of Federal Regulations Part 50 (10CFR50). The Nuclear Regulatory Commission's basic proposal is to allow modification of some of the special treatment requirements of 10CFR50. Their effort is proceeding via an Advanced Notice of Public Rulemaking, March 3, 2000, and an announcement of Availability of Draft Rule Wording, November 29, 2001, to add 10 CFR 50.69, 'Risk-Informed Treatment of Structures, Systems and Components'. A parallel task by the Nuclear Energy Institute (NEI) to develop a guideline on how to implement the results of the rulemaking is also well underway via NEI 00-04 (Draft Revision B), 'Option 2 Implementation Guideline', May 2001. This paper summarizes the content and status of approval of the proposed ASME Code Cases, including how they relate to the above NRC and NEI efforts. Some initial results from trial application of the Code Cases will also be cited. (authors)

Comparison Between Predictions and Measurements of Performance Characteristics for an Eight Pocket Hybrid (Combination Hydrostatic and Hydrodynamic) Thrust Bearing

Science.gov (United States)

2008-12-03

STB stainless steel housing. Drive End Thrust Collar Free End Splash Guard Slave Thrust Bearing Face STB Flange Figure 12: Exploded view of slave...Bulk Flow Analysis of Hybrid Thrust Bearing for Process Fluid Applications.” ASME Trans., Journal of Tribology , January, Vol. 122 (1), pp. 170-180...ASME Journal of Tribology , Vol. 123, pp. 768-776 [5] San Andrés, L., (2006), “MEEN 626 Notes 2 Derivation of the Classical Reynolds Equation for

Procedures of ASME code case N-201 for KALIMER. Reactor internal structures

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Yoo, B.

2001-02-01

The main objective of this report is to describe the design procedure of ASME Boiler and Pressure Vessel Code, Code Case N-201-4, which is an elevated temperature structural design code of the Nuclear reactor internal structures, checking the criteria of stress limit, accumulated inelastic strain and deformation, creep-fatigue damage, and buckling limit. As one of examples, the creep-fatigue damage evaluations are carried out for the KALIMER reactor internal structures of baffle annulus. This report is expected to be very useful in evaluating the structural integrity of the liquid metal reactor operating under an elevated temperature

ASME N510 test results for Savannah River Site AACS filter compartments

Energy Technology Data Exchange (ETDEWEB)

Paul, J.D.; Punch, T.M. [Westinghouse Savannah River Company, Aiken, SC (United States)

1995-02-01

The K-Reactor at the Savannah River Site recently implemented design improvements for the Airborne Activity Confinement System (AACS) by procuring, installing, and testing new Air Cleaning Units, or filter compartments, to ASME AG-11, N509, and N510 requirements. Specifically, these new units provide documentable seismic resistance to a Design Basis Accident earthquake, provide 2 inch adsorber beds with 0.25 second residence time, and meet all AG-1, N509, and N510 requirements for testability and maintainability. This paper presents the results of the Site acceptance testing and discusses an issue associated with sample manifold qualification testing.

Performance of a generic non-axisymmetric end wall in a single stage, rotating turbine at on and off-design conditions

CSIR Research Space (South Africa)

Snedden, Glen C

2010-06-01

Full Text Available ) “Low Pressure Turbine Design for Rolls-Royce TRENT 900 Turbofan”, ASME Turbo Expo, GT2006-90997. [5] Denton J. D., (1993) “Loss Mechanisms in Turbomachines,” Transactions of the ASME Journal of Turbomachinery, Vol. 115, pp. 621-650. [6] Langston...

Design specifications for ASME B and PV Code Section III nuclear class 1 piping

International Nuclear Information System (INIS)

Richardson, J.A.

1978-01-01

ASME B and PV Code Section III code regulations for nuclear piping requires that a comprehensive Design Specification be developed for ensuring that the design and installation of the piping meets all code requirements. The intent of this paper is to describe the code requirements, discuss the implementation of these requirements in a typical Class 1 piping design specification, and to report on recent piping failures in operating light water nuclear power plants in the US. (author)

Report on ANSI/ASME nuclear air and gas treatment standards for nuclear power plants

International Nuclear Information System (INIS)

Fish, J.F.

1979-01-01

Original N Committee, N45-8, has completed and published through the approved American National Standards Institute process two Standards, N-509 and N-510. This committee has been dissolved and replaced by ASME Committee on Nuclear Air and Gas Treatment with expanded scope to cover not only air cleaning, but thermal treatment equipment. Current efforts are directed to produce Code documents rather than Standards type publications. This report summarizes changed scope, current organization and sub-committee coverage areas

Ethnographic journalism

DEFF Research Database (Denmark)

Hermann, Anne Kirstine

2016-01-01

require more contextual reporting, ethnographic journalism emerges in American feature journalism. Analyzed holistically, this genre is characterized as the employment of immersion strategies adopted from social science for distinct storytelling purposes. These methods, however, transform conventional......Accounting for emerging journalistic genres is a difficult endeavor not least because there is little agreement as to what constitutes journalism itself. Doing so, however, is essential if we are to recognize changing journalistic doxas. To capture such changes, we must include a holistic framework...... journalistic epistemology, changing it through practice. In turn, the analysis reveals how journalism practices can evolve its troubled philosophical position...

Probing the Mysteries of the X-Ray Binary 4U 1210-64 with ASM, MAXI and Suzaku

Science.gov (United States)

Coley, Joel B.; Corbet, R.; Mukai, K.; Pottschmidt, K.

2013-01-01

Optical and X-ray observations of 4U 1210-64 (1ES 1210-646) suggest that the source is a High Mass X-ray Binary (HMXB) probably powered by the Be mechanism. Data acquired by the RXTE All Sky Monitor (ASM), the ISS Monitor of All-sky X-ray Image (MAXI) and Suzaku provide a detailed temporal and spectral description of this poorly understood source. Long-term data produced by ASM and MAXI indicate that the source shows two distinct high and low states. A 6.7-day orbital period of the system was found in folded light curves produced by both ASM and MAXI. A two day Suzaku observation in Dec. 2010 took place during a transition from the minimum to the maximum of the folded light curve. The two day Suzaku observation reveals large variations in flux indicative of strong orbit to orbit variability. Flares in the Suzaku light curve can reach nearly 1.4 times the mean count rate. From a spectral analysis of the Suzaku data, emission lines in the Fe K alpha region were detected at 6.4 keV, 6.7 keV and 6.97 keV interpreted as FeI, FeXXV and FeXXVI. In addition, emission lines were observed at approximately 1.0 and 2.6 keV, corresponding to NeX and SXVI respectively. Thermal bremsstrahlung or power law models both modified by interstellar and partially covering absorption provide a good fit to the continuum data. This source is intriguing for these reasons: i) No pulse period was observed; ii) 6.7 day orbital period is much less than typical orbital periods seen in Be/X-ray Binaries; iii) The optical companion is a B5V--an unusual spectral class for an HMXB; iv) There are extended high and low X-ray states.

Present activity in ASME Section XI regarding risk-informed maintenance

International Nuclear Information System (INIS)

Hedden, Owen; Chockie, Alan

2005-01-01

Since 1996 Section XI of the ASME Boiler and Pressure Vessel Code has actively incorporated risk-informed concepts. The risk-informed process provides a framework for allocating inspection resources in a cost-effective manner and helps focus inspections where most critical for plant safety. Based on the success of the risk-informed ISI piping applications at US and non-US plants, Section XI has refined existing Code Cases and expanded the use of the risk-informed process to a variety of high-risk components and systems. The risk informed approach started in the area of inspection and is now being expanded to other plant maintenance activities. This article summarizes the Section XI actions and the continued development of the risk-informed process to improve nuclear plant maintenance. (author)

Evaluation of conservatisms and environmental effects in ASME Code, Section III, Class 1 fatigue analysis

International Nuclear Information System (INIS)

Deardorff, A.F.; Smith, J.K.

1994-08-01

This report documents the results of a study regarding the conservatisms in ASME Code Section 3, Class 1 component fatigue evaluations and the effects of Light Water Reactor (LWR) water environments on fatigue margins. After review of numerous Class 1 stress reports, it is apparent that there is a substantial amount of conservatism present in many existing component fatigue evaluations. With little effort, existing evaluations could be modified to reduce the overall predicted fatigue usage. Areas of conservatism include design transients considerably more severe than those experienced during service, conservative grouping of transients, conservatisms that have been removed in later editions of Section 3, bounding heat transfer and stress analysis, and use of the ''elastic-plastic penalty factor'' (K 3 ). Environmental effects were evaluated for two typical components that experience severe transient thermal cycling during service, based on both design transients and actual plant data. For all reasonable values of actual operating parameters, environmental effects reduced predicted margins, but fatigue usage was still bounded by the ASME Section 3 fatigue design curves. It was concluded that the potential increase in predicted fatigue usage due to environmental effects should be more than offset by decreases in predicted fatigue usage if re-analysis were conducted to reduce the conservatisms that are present in existing component fatigue evaluations

Acid sphingomyelinase (Asm) deficiency patients in The Netherlands and Belgium: disease spectrum and natural course in attenuated patients.

Science.gov (United States)

Hollak, C E M; de Sonnaville, E S V; Cassiman, D; Linthorst, G E; Groener, J E; Morava, E; Wevers, R A; Mannens, M; Aerts, J M F G; Meersseman, W; Akkerman, E; Niezen-Koning, K E; Mulder, M F; Visser, G; Wijburg, F A; Lefeber, D; Poorthuis, B J H M

2012-11-01

Niemann-Pick disease (NPD) is a neurovisceral lysosomal storage disorder caused by acid sphingomyelinase (ASM) deficiency, which can be categorized as either Niemann-Pick disease type A [NPD-A], with progressive neurological disease and death in early childhood, or as Niemann-Pick disease type B [NPD-B], with a more variable spectrum of manifestations. Enzyme replacement therapy (ERT) with recombinant sphingomyelinase is currently studied as potential treatment for NPD-B patients. The objective of this study is to characterize the clinical features of patients with ASM deficiency in the Netherlands and Belgium with focus on the natural disease course of NPD-B patients. Prospective and retrospective data on ASM deficient patients were collected in The Netherlands and part of Belgium. Patients with NPD-B that could be followed prospectively were evaluated every 6-12 months for pulmonary function tests, 6 minute walk test (6 MWT), imaging (bone marrow infiltration measured by QCSI, organ volumes by MRI and CT scan of the lungs) and biochemical markers. Twenty-five patients with ASM deficiency were identified (13 males, 12 females, median age 13years, range 1-59 years). Nine patients had died at the time of the study, including four NPD-A patients at the age of 1,1, 2, 3 and five NPDB patents at the age of 5, 6, 43, 56 and 60 years. There was a high prevalence of homozygosity and compound heterozygosity for the common p.Arg608del mutation in 43% and 19% of NPD-B patients, respectively. In NPD-B patients, thrombocytopenia was present in most, while anemia and leucopenia were less common (33% and 6 % respectively). HDL cholesterol was reduced in most patients. Pulmonary disease was severe in several patients. Follow-up up to 11 years revealed a gradual decrease in platelet count. Detailed investigations in 6 NPD-B patients with follow-up in 4 patients revealed remarkable stable disease parameters up to 6 years, with some decline in pulmonary function and 6 MWT. Bone

Optimized periodic verification testing blended risk and performance-based MOV inservice test program an application of ASME code case OMN-1

Energy Technology Data Exchange (ETDEWEB)

Sellers, C.; Fleming, K.; Bidwell, D.; Forbes, P. [and others

1996-12-01

This paper presents an application of ASME Code Case OMN-1 to the GL 89-10 Program at the South Texas Project Electric Generating Station (STPEGS). Code Case OMN-1 provides guidance for a performance-based MOV inservice test program that can be used for periodic verification testing and allows consideration of risk insights. Blended probabilistic and deterministic evaluation techniques were used to establish inservice test strategies including both test methods and test frequency. Described in the paper are the methods and criteria for establishing MOV safety significance based on the STPEGS probabilistic safety assessment, deterministic considerations of MOV performance characteristics and performance margins, the expert panel evaluation process, and the development of inservice test strategies. Test strategies include a mix of dynamic and static testing as well as MOV exercising.

Optimized periodic verification testing blended risk and performance-based MOV inservice test program an application of ASME code case OMN-1

International Nuclear Information System (INIS)

Sellers, C.; Fleming, K.; Bidwell, D.; Forbes, P.

1996-01-01

This paper presents an application of ASME Code Case OMN-1 to the GL 89-10 Program at the South Texas Project Electric Generating Station (STPEGS). Code Case OMN-1 provides guidance for a performance-based MOV inservice test program that can be used for periodic verification testing and allows consideration of risk insights. Blended probabilistic and deterministic evaluation techniques were used to establish inservice test strategies including both test methods and test frequency. Described in the paper are the methods and criteria for establishing MOV safety significance based on the STPEGS probabilistic safety assessment, deterministic considerations of MOV performance characteristics and performance margins, the expert panel evaluation process, and the development of inservice test strategies. Test strategies include a mix of dynamic and static testing as well as MOV exercising

Thermal-structural Analysis and Fatigue Life Evaluation of a Parallel Slide Gate Valve in Accordance with ASME B and PVC

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Ho; Han, Jeong Sam [Andong Nat’l Univ., Andong (Korea, Republic of); Jae Seung Choi [Key Valve Technologies Ltd., Siheung (Korea, Republic of)

2017-02-15

A parallel slide gate valve (PSGV) is located between the heat recovery steam generator (HRSG) and the steam turbine in a combined cycle power plant (CCPP). It is used to control the flow of steam and runs with repetitive operations such as startups, load changes, and shutdowns during its operation period. Therefore, it is necessary to evaluate the fatigue damage and the structural integrity under a large compressive thermal stress due to the temperature difference through the valve wall thickness during the startup operations. In this paper, the thermal-structural analysis and the fatigue life evaluation of a 16-inch PSGV, which is installed on the HP steam line, is performed according to the fatigue life assessment method described in the ASME B and PVC VIII-2; the method uses the equivalent stress from the elastic stress analysis.

Code cases for implementing risk-based inservice testing in the ASME OM code

International Nuclear Information System (INIS)

Rowley, C.W.

1996-01-01

Historically inservice testing has been reasonably effective, but quite costly. Recent applications of plant PRAs to the scope of the IST program have demonstrated that of the 30 pumps and 500 valves in the typical plant IST program, less than half of the pumps and ten percent of the valves are risk significant. The way the ASME plans to tackle this overly-conservative scope for IST components is to use the PRA and plant expert panels to create a two tier IST component categorization scheme. The PRA provides the quantitative risk information and the plant expert panel blends the quantitative and deterministic information to place the IST component into one of two categories: More Safety Significant Component (MSSC) or Less Safety Significant Component (LSSC). With all the pumps and valves in the IST program placed in MSSC or LSSC categories, two different testing strategies will be applied. The testing strategies will be unique for the type of component, such as centrifugal pump, positive displacement pump, MOV, AOV, SOV, SRV, PORV, HOV, CV, and MV. A series of OM Code Cases are being developed to capture this process for a plant to use. One Code Case will be for Component Importance Ranking. The remaining Code Cases will develop the MSSC and LSSC testing strategy for type of component. These Code Cases are planned for publication in early 1997. Later, after some industry application of the Code Cases, the alternative Code Case requirements will gravitate to the ASME OM Code as appendices

Code cases for implementing risk-based inservice testing in the ASME OM code

Energy Technology Data Exchange (ETDEWEB)

Rowley, C.W.

1996-12-01

Historically inservice testing has been reasonably effective, but quite costly. Recent applications of plant PRAs to the scope of the IST program have demonstrated that of the 30 pumps and 500 valves in the typical plant IST program, less than half of the pumps and ten percent of the valves are risk significant. The way the ASME plans to tackle this overly-conservative scope for IST components is to use the PRA and plant expert panels to create a two tier IST component categorization scheme. The PRA provides the quantitative risk information and the plant expert panel blends the quantitative and deterministic information to place the IST component into one of two categories: More Safety Significant Component (MSSC) or Less Safety Significant Component (LSSC). With all the pumps and valves in the IST program placed in MSSC or LSSC categories, two different testing strategies will be applied. The testing strategies will be unique for the type of component, such as centrifugal pump, positive displacement pump, MOV, AOV, SOV, SRV, PORV, HOV, CV, and MV. A series of OM Code Cases are being developed to capture this process for a plant to use. One Code Case will be for Component Importance Ranking. The remaining Code Cases will develop the MSSC and LSSC testing strategy for type of component. These Code Cases are planned for publication in early 1997. Later, after some industry application of the Code Cases, the alternative Code Case requirements will gravitate to the ASME OM Code as appendices.

Analysis and Elimination of High Temperature Notch Induced Microcrack Initiation in Inconel 718 Nickel-Based Alloy

Science.gov (United States)

1989-01-01

Compressor Rear Frame (ClF) which exhibits extensive cract:ing of the forward flange. ThL 1988 Actuarial Function data shows CRF crackiing As the number 2...Creep-Rupture properties of Waspaloy sheet to Sharp-Edged Notches in the Temperature Range of 1O000F-14O0OF. Journal of Basle Engineering, Trans ASME ...Dependence of the Notch Sensitivity of Waspaloy at 10000F-1400F on the Gamma Prime Phase, Journal of Basic Engineering, Trans ASME (in print at time of

Development of a software for the ASME code qualification of class-I nuclear piping systems

International Nuclear Information System (INIS)

Mishra, Rajesh; Umashankar, C.; Soni, R.S.; Kushwaha, H.S.; Venkat Raj, V.

1999-11-01

In nuclear industry, the designer often comes across the requirements of Class-1 piping systems which need to be qualified for various normal and abnormal loading conditions. In order to have quick design changes and the design reviews at various stages of design, it is quite helpful if a dedicated software is available for the qualification of Class-1 piping systems. BARC has already purchased a piping analysis software CAESAR-II and has used it for the life extension of heavy water plant, Kota. CAESAR-II facilitates the qualification of Class-2 and Class-3 piping systems among others. However, the present version of CAESAR-II does not have the capability to perform stress checks for the ASME Class-1 nuclear piping systems. With this requirement in mind and the prohibitive costs of commercially available software for the Class-1 piping analyses, it was decided to develop a separate software for this class of piping in such a way that the input and output details of the piping from the CAESAR-II software can be made use of. This report principally contains the details regarding development of a software for codal qualification of Class-1 nuclear piping as per ASME code section-III, NB-3600. The entire work was carried out in three phases. The first phase consisted of development of the routines for reading the output files obtained from the CAESAR-II software, and converting them into required format for further processing. In this phase, the nodewise informations available from the CAESAR-II output file were converted into element-wise informations. The second phase was to develop a general subroutine for reading the various input parameters such as diameter, wall thickness, corrosion allowance, bend radius and also to recognize the bend elements based on the bend radius, directly from the input file of CAESAR-II software. The third phase was regarding the incorporation of the required steps for performing the ASME codal checks as per NB-3600 for Class-1 piping

Nupack, the new Asme code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as 'Nupack', has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper. Participation in the Nupack development work described in this paper was supported by the U.S. Department of Energy. (authors)

Analysis of Statistical Methods Currently used in Toxicology Journals.

Science.gov (United States)

Na, Jihye; Yang, Hyeri; Bae, SeungJin; Lim, Kyung-Min

2014-09-01

Statistical methods are frequently used in toxicology, yet it is not clear whether the methods employed by the studies are used consistently and conducted based on sound statistical grounds. The purpose of this paper is to describe statistical methods used in top toxicology journals. More specifically, we sampled 30 papers published in 2014 from Toxicology and Applied Pharmacology, Archives of Toxicology, and Toxicological Science and described methodologies used to provide descriptive and inferential statistics. One hundred thirteen endpoints were observed in those 30 papers, and most studies had sample size less than 10, with the median and the mode being 6 and 3 & 6, respectively. Mean (105/113, 93%) was dominantly used to measure central tendency, and standard error of the mean (64/113, 57%) and standard deviation (39/113, 34%) were used to measure dispersion, while few studies provide justifications regarding why the methods being selected. Inferential statistics were frequently conducted (93/113, 82%), with one-way ANOVA being most popular (52/93, 56%), yet few studies conducted either normality or equal variance test. These results suggest that more consistent and appropriate use of statistical method is necessary which may enhance the role of toxicology in public health.

Results from Evaluation of Proposed ASME AG-1 Section FI Metal Media Filters - 13063

Energy Technology Data Exchange (ETDEWEB)

Wilson, John A.; Giffin, Paxton K.; Parsons, Michael S.; Waggoner, Charles A. [Institute for Clean Energy Technology, Mississippi State University, 205 Research Blvd Starkville, MS 39759 (United States)

2013-07-01

High efficiency particulate air (HEPA) filtration technology is commonly used in Department of Energy (DOE) facilities that require control of radioactive particulate matter (PM) emissions due to treatment or management of radioactive materials. Although HEPA technology typically makes use of glass fiber media, metal and ceramic media filters are also capable of filtering efficiencies beyond the required 99.97%. Sintered metal fiber filters are good candidates for use in DOE facilities due to their resistance to corrosive environments and resilience at high temperature and elevated levels of relative humidity. Their strength can protect them from high differential pressure or pressure spikes and allow for back pulse cleaning, extending filter lifetime. Use of these filters has the potential to reduce the cost of filtration in DOE facilities due to life cycle cost savings. ASME AG-1 section FI has not been approved due to a lack of protocols and performance criteria for qualifying section FI filters. The Institute for Clean Energy Technology (ICET) with the aid of the FI project team has developed a Section FI test stand and test plan capable of assisting in the qualification ASME AG-1 section FI filters. Testing done at ICET using the FI test stand evaluates resistance to rated air flow, test aerosol penetration and resistance to heated air of the section FI filters. Data collected during this testing consists of temperature, relative humidity, differential pressure, flow rate, upstream particle concentration, and downstream particle concentration. (authors)

Prospective Science Teachers' Attitudes and Views of Using Journal Writing in the "Methods of Teaching Science" Course

Science.gov (United States)

Ambusaidi, Abdullah

2014-01-01

The aim of this study was to investigate the attitudes of prospective science teachers at Sultan Qaboos University towards and their views about using journal writing in the Methods of Teaching Science course. Twenty-six prospective science teachers were asked to write about each topic in the course in their journal to show their understanding of…

Journaling: identification of challenges and reflection on strategies.

Science.gov (United States)

Hayman, Brenda; Wilkes, Lesley; Jackson, Debra

2012-01-01

To identify the challenges associated with using journaling as a method of data collection and to offer strategies for effectively managing those challenges. While journaling can be used for a variety of reasons, in the context of this paper, journaling refers to the process of participants sharing thoughts, ideas, feelings and experiences through writing and/or other media. Journaling is used in phenomenological research studies to record participant experiences in their natural contexts. The findings are based on the experiences of the researchers during a qualitative study that explored the experiences of lesbian mothers and used journaling as one method of data collection. This is a methodological paper. Three main challenges affect journaling as a method of data collection: poor participation, feeling exposed and staying on track. Six strategies to promote participation in journaling are: coaching participants, limiting the journaling period, providing follow-up contact, promoting comfort, ensuring safety and providing clear content expectations. Each strategy is discussed and methods of implementing the strategies are offered. Journaling as a method of data collection has long been accepted as a valid method of accessing rich qualitative data. By acknowledging the common challenges associated with the process of journaling that are experienced by the participants, researchers employing this data collection method can promote constructive and valuable participation. Further research examining participants' experiences of journaling as a method of qualitative data collection would be useful in determining challenges, barriers and benefits of the method.

User-inspired design methodology using Affordance Structure Matrix (ASM for construction projects

Directory of Open Access Journals (Sweden)

Maheswari J. Uma

2017-01-01

Full Text Available Traditionally, design phase of construction projects is often performed with incomplete and inaccurate user preferences. This is due to inefficiencies in the methodologies used for capturing the user requirements that can subsequently lead to inconsistencies and result in non-optimised end-result. Iterations and subsequent reworks due to such design inefficiencies is one of the major reasons for unsuccessful project delivery as they impact project performance measures such as time and cost among others. The existing design theories and practice are primarily based on functional requirements. Function-based design deals with design of artifact alone, which may yield favourable or unfavourable consequences with the design artifact. However, incorporating other interactions such as interactions between user & designer is necessary for optimised end-result. Hence, the objective of this research work is to devise a systematic design methodology considering all the three interactions among users, designers and artefacts for improved design efficiency. In this study, it has been attempted to apply the theory of affordances in a case project that involves the design of an offshore facility. A step-by-step methodology for developing Affordance Structure Matrix (ASM, which integrates House of Quality (HOQ and Design Structure Matrix (DSM, is proposed that can effectively capture the user requirements. HOQ is a popular quality management tool for capturing client requirements and DSM is a matrix-based tool that can capture the interdependency among the design entities. The proposed methodology utilises the strengths of both the tools, as DSM compliments HOQ in the process. In this methodology, different affordances such as AUA (Artifact-User-Affordance, AAA (Artifact-Artifact-Affordance and DDA (Designer-Designer-Affordance are captured systematically. Affordance is considered to be user-driven in this context that is in contrast to prevailing design

Twenty years of fracture mechanics and flaw evaluation applications in the ASME Nuclear Code

International Nuclear Information System (INIS)

Riccardella, P.C.

1991-01-01

The paper presents a retrospective on the development and applications of fracture mechanics-based toughness requirements and flaw evaluation methodology in Sections III and XI of the ASME Code. Section III developments range from the rules and requirements for thick section Class 1 pressure vessels to thinner section components in other Classes. Section XI applications include flaw acceptance standards and evaluation methodology for various components ranging from pressure vessels to thins section piping of carbon and austenitic steels. The experience gained in operating plant applications of these rules and procedures are also discussed

A method for assessment of the shape of the proximal femur and its relationship to osteoporotic hip fracture.

Science.gov (United States)

Gregory, J S; Testi, D; Stewart, A; Undrill, P E; Reid, D M; Aspden, R M

2004-01-01

The shape of the proximal femur has been demonstrated to be important in the occurrence of fractures of the femoral neck. Unfortunately, multiple geometric measurements frequently used to describe this shape are highly correlated. A new method, active shape modeling (ASM) has been developed to quantify the morphology of the femur. This describes the shape in terms of orthogonal modes of variation that, consequently, are all independent. To test this method, digitized standard pelvic radiographs were obtained from 26 women who had suffered a hip fracture and compared with images from 24 age-matched controls with no fracture. All subjects also had their bone mineral density (BMD) measured at five sites using dual-energy X-ray absorptiometry. An ASM was developed and principal components analysis used to identify the modes which best described the shape. Discriminant analysis was used to determine which variable, or combination of variables, was best able to discriminate between the groups. ASM alone correctly identified 74% of the individuals and placed them in the appropriate group. Only one of the BMD values (Ward's triangle) achieved a higher value (82%). A combination of Ward's triangle BMD and ASM improved the accuracy to 90%. Geometric variables used in this study were weaker, correctly classifying less than 60% of the study group. Logistic regression showed that after adjustment for age, body mass index, and BMD, the ASM data was still independently associated with hip fracture (odds ratio (OR)=1.83, 95% confidence interval 1.08 to 3.11). The odds ratio was calculated relative to a 10% increase in the probability of belonging to the fracture group. Though these initial results were obtained from a limited data set, this study shows that ASM may be a powerful method to help identify individuals at risk of a hip fracture in the future.

Journal Benchmarking for Strategic Publication Management and for Improving Journal Positioning in the World Ranking Systems

Science.gov (United States)

Moskovkin, Vladimir M.; Bocharova, Emilia A.; Balashova, Oksana V.

2014-01-01

Purpose: The purpose of this paper is to introduce and develop the methodology of journal benchmarking. Design/Methodology/ Approach: The journal benchmarking method is understood to be an analytic procedure of continuous monitoring and comparing of the advance of specific journal(s) against that of competing journals in the same subject area,…

The ASME section XI code, past, present, and future

International Nuclear Information System (INIS)

Anderson, W.F.; Bush, S.H.; Chockie, L.J.

1982-01-01

A little over a decade has passed since the first drafts of the Codes effecting the program of inservice inspections in the United States have been implemented and enforced in operating power plants. During the ensuing years, advantage has been taken of results of the application of the program of inspections and tests. In several instances, the Code has been revised to correct deficiencies, and additional rules have been added to accommodate additional systems and portions of the plant which were deemed to also be important to safety. Additional rules have now been published to recognize the liquid metal cooled reactor systems and the gas cooled reactor systems along with the water cooled reactor systems. While the past and the present can be stated with considerable certainty, opinions of the authors, each of whom is a member of the American Society of Mechanical Engineers (ASME) Code Committee, are advanced as to their plans which will reveal the direction the Code is projected to follow in the future. (author)

Comparison Between Impact Factor, Eigenfactor Metrics, and SCimago Journal Rank Indicator of Pediatric Neurology Journals

OpenAIRE

Kianifar, Hamidreza; Sadeghi, Ramin; Zarifmahmoudi, Leili

2014-01-01

Background: Impact Factor (IF) as a major journal quality indicator has a series of shortcomings including effect of self-citation, review articles, total number of articles, etc. In this study, we compared 4 journals quality indices ((IF), Eigenfactor Score (ES), Article Influence Score (AIS) and SCImago Journal Rank indicator (SJR)) in the specific Pediatric Neurology journals. Methods: All ISI and Scopus indexed specific Pediatric Neurology journals were compared regarding their 2011 IF, E...

Qualitative and Quantitative Status and International Visibility of Iranian Journals Indexed in Journal Citation Reports

Directory of Open Access Journals (Sweden)

Mohammadamin Erfanmanesh

2016-12-01

Full Text Available Objectives: The present study aims to investigate the international status and visibility of Iranian journals which have been indexed in Journal Citation Reports (JCR. Accordingly, the number of international papers, citations and editorial board members of each journal was studied. Moreover, various measures were utilized to compare the quality of Iranian journals with their international counterparts. Method: Current paper applied scientometric research method. A total of 16471 papers which published in 38 Iranian journals and indexed by the JCR 2013 were selected as the population of the study. Web of Science (WoS, JCR and journals’ website were used for data gathering. Results: Results of the study revealed that foreign researchers have published 34.8% of papers published in Iranian ISI journals. Moreover, only 30.6% of citations to Iranian ISI journals have been received from foreign papers or Iranian internationally collaborative papers. The results showed that Iranian researchers accounted for 66.4% of editorial board member of all studied journals, while foreign researchers only occupied 33.6% of the editorial board positions. Based on the findings, only two Iranian journals have impact factors above the median of the journals in the disciplinary category areas in which they are classified in JCR. Furthermore, only 8 Iranian journals have ever been placed in the 1st and 2nd quartile of journals of the same field in the JCR. Findings also showed that 36 out of the 38 Iranian journals have mostly cited by journals with higher median impact factors than cited journals. Conclusion: The findings indicate that the share of international papers, citations and editorial board memberships is low in Iranian ISI journals. Moreover, Iranian journals’ impact factor was below of those of the leading journals.

A simple objective method for determining a dynamic journal collection.

Science.gov (United States)

Bastille, J D; Mankin, C J

1980-10-01

In order to determine the content of a journal collection responsive to both user needs and space and dollar constraints, quantitative measures of the use of a 647-title collection have been related to space and cost requirements to develop objective criteria for a dynamic collection for the Treadwell Library at the Massachusetts General Hospital, a large medical research center. Data were collected for one calendar year (1977) and stored with the elements for each title's profile in a computerized file. To account for the effect of the bulk of the journal runs on the number of uses, raw use data have been adjusted using linear shelf space required for each title to produce a factor called density of use. Titles have been ranked by raw use and by density of use with space and cost requirements for each. Data have also been analyzed for five special categories of use. Given automated means of collecting and storing data, use measures should be collected continuously. Using raw use frequency ranking to relate use to space and costs seems sensible since a decision point cutoff can be chosen in terms of the potential interlibrary loans generated. But it places new titles at risk while protecting titles with long, little used runs. Basing decisions on density of use frequency ranking seems to produce a larger yield of titles with fewer potential interlibrary loans and to identify titles with overlong runs which may be pruned or converted to microform. The method developed is simple and practical. Its design will be improved to apply to data collected in 1980 for a continuous study of journal use. The problem addressed is essentially one of inventory control. Viewed as such it makes good financial sense to measure use as part of the routine operation of the library to provide information for effective management decisions.

Normalized impact factor (NIF): an adjusted method for calculating the citation rate of biomedical journals.

Science.gov (United States)

Owlia, P; Vasei, M; Goliaei, B; Nassiri, I

2011-04-01

The interests in journal impact factor (JIF) in scientific communities have grown over the last decades. The JIFs are used to evaluate journals quality and the papers published therein. JIF is a discipline specific measure and the comparison between the JIF dedicated to different disciplines is inadequate, unless a normalization process is performed. In this study, normalized impact factor (NIF) was introduced as a relatively simple method enabling the JIFs to be used when evaluating the quality of journals and research works in different disciplines. The NIF index was established based on the multiplication of JIF by a constant factor. The constants were calculated for all 54 disciplines of biomedical field during 2005, 2006, 2007, 2008 and 2009 years. Also, ranking of 393 journals in different biomedical disciplines according to the NIF and JIF were compared to illustrate how the NIF index can be used for the evaluation of publications in different disciplines. The findings prove that the use of the NIF enhances the equality in assessing the quality of research works produced by researchers who work in different disciplines. Copyright © 2010 Elsevier Inc. All rights reserved.

What are Bogus Journal

Directory of Open Access Journals (Sweden)

Willy A. Renandya

2014-11-01

Full Text Available Abstract The purpose of this paper is to warn novice researchers/writers of the danger of publishing in journals of questionable quality (often referred to as bogus, scam or predatory journals and highlight key characteristics of these journals and their method of operation. Understanding the characteristics and how they operate could help us avoid publishing our work in scam journals. These journals claim (falsely that they employ a blind review process by experts in the field, promise quick turnaround, claim legitimacy by quoting the ISSN and listing a number of databases in which they are indexed (e.g., EBSCO, DOAJ and PROQUEST. The paper outlines 15 reasons why as members of the academic community we should shun journals of dubious quality. The key message of this paper is that before we send our scholarly work to academic journals, we need to invest time doing our due diligence, making sure that our target journal is a legitimate and respectable outlet for our work.

Content and Method Trends in the "Journal of Community Psychology" between 2003 and 2007

Science.gov (United States)

Graham, Tanya M.; Ismail, Tasneem

2011-01-01

Ongoing inquiry into the characteristics of published work and its synergy with community psychology's core principles is an important reflexive endeavour in the field's continuing development. This study examined topic and method trends within the "Journal of Community Psychology" during a 5-year period (January 2003-December 2007).…

Dynamic experiments with high bisphenol-A concentrations modelled with an ASM model extended to include a separate XOC degrading microorganism

DEFF Research Database (Denmark)

Lindblom, Erik Ulfson; Press-Kristensen, Kåre; Vanrolleghem, P.A.

2009-01-01

The perspective of this work is to develop a model, which can be used to better understand and optimize wastewater treatment plants that are able to remove xenobiotic organic compounds (XOCs) in combination with removal of traditional pollutants. Results from dynamic experiments conducted...... with the endocrine disrupting XOC bisphenol-A (BPA) in an activated sludge process with real wastewater were used to hypothesize an ASM-based process model including aerobic growth of a specific BPA-degrading microorganism and sorption of BPA to sludge. A parameter estimation method was developed, which...... simultaneously utilizes steady-state background concentrations and dynamic step response data, as well as conceptual simplifications of the plant configuration. Validation results show that biodegradation of BPA is sensitive to operational conditions before and during the experiment and that the proposed model...

Effect of beta2-adrenoceptor agonists and other cAMP-elevating agents on inflammatory gene expression in human ASM cells: a role for protein kinase A.

Science.gov (United States)

Kaur, Manminder; Holden, Neil S; Wilson, Sylvia M; Sukkar, Maria B; Chung, Kian Fan; Barnes, Peter J; Newton, Robert; Giembycz, Mark A

2008-09-01

In diseases such as asthma, airway smooth muscle (ASM) cells play a synthetic role by secreting inflammatory mediators such as granulocyte-macrophage colony-stimulating factor (GM-CSF), IL-6, or IL-8 and by expressing surface adhesion molecules, including ICAM-1. In the present study, PGE(2), forskolin, and short-acting (salbutamol) and long-acting (salmeterol and formoterol) beta(2)-adrenoceptor agonists reduced the expression of ICAM-1 and the release of GM-CSF evoked by IL-1beta in ASM cells. IL-1beta-induced IL-8 release was also repressed by PGE(2) and forskolin, whereas the beta(2)-adrenoceptor agonists were ineffective. In each case, repression of these inflammatory indexes was prevented by adenoviral overexpression of PKIalpha, a highly selective PKA inhibitor. These data indicate a PKA-dependent mechanism of repression and suggest that agents that elevate intracellular cAMP, and thereby activate PKA, may have a widespread anti-inflammatory effect in ASM cells. Since ICAM-1 and GM-CSF are highly NF-kappaB-dependent genes, we used an adenoviral-delivered NF-kappaB-dependent luciferase reporter to examine the effects of forskolin and the beta(2)-adrenoceptor agonists on NF-kappaB activation. There was no effect on luciferase activity measured in the presence of forskolin or beta(2)-adrenoceptor agonists. This finding is consistent with the observation that IL-1beta-induced expression of IL-6, a known NF-kappaB-dependent gene in ASM, was also unaffected by beta(2)-adrenoceptor agonists, forskolin, PGE(2), 8-bromo-cAMP, or rolipram. Collectively, these results indicate that repression of IL-1beta-induced ICAM-1 expression and GM-CSF release by cAMP-elevating agents, including beta(2)-adrenoceptor agonists, may not occur through a generic effect on NF-kappaB.

Algorithmic Procedure for Finding Semantically Related Journals.

Science.gov (United States)

Pudovkin, Alexander I.; Garfield, Eugene

2002-01-01

Using citations, papers and references as parameters a relatedness factor (RF) is computed for a series of journals. Sorting these journals by the RF produces a list of journals most closely related to a specified starting journal. The method appears to select a set of journals that are semantically most similar to the target journal. The…

ASME stress linearization and classification - a discussion based on a case study

International Nuclear Information System (INIS)

Miranda, Carlos A. de J.; Faloppa, Altair A.; Mattar Neto, Miguel; Fainer, Gerson

2011-01-01

The ASME code, specially in its Nuclear Division (Subsection NB - Class I Components), gives some recommendations to the structural analyst on how to perform the verifications required to prove the design as good as the by-analysis prevented failures modes. Each of these failure modes has specific stress limits which are established based on simple but conservative hypothesis like the material perfectly plastic behavior and the shell theory with its typical membrane and bending stresses with linear distribution along the thickness. Other detail to keep in mind is the code distinction between primary and secondary stresses (respectively, stress that came due to equilibrium and due to displacement compatibility). In general, the numerical models used in the analyses are developed with plane or 3D solid elements and due this fact no direct comparison with the code limits can be done and, besides that, the programs do not distinguish between primary and secondary stresses. Mostly, the later are produced due to the temperature variation but they also appear near discontinuities. Sometimes, this classification is not so clear or direct. To perform the required ASME Code verifications the analyst should obtain the membrane and bending stresses from the plane or 3-D model which is called stress linearization and, also, should classify them as primary and secondary. (The excess between the maximum stress at a point and the sum of these linearized values is called peak stress and is included in the fatigue verification.) This task, most of the time is not a simple one due to the nature of the involved load and/or the complex geometry under analysis. In fact, there are several studies discussing on how to perform these stress classification and linearization. The present paper shows a discussion on how to perform these verifications based on a generic geometry found in many plants, from petrochemical to nuclear, which emphasizes some of theses issues. (author)

ASME stress linearization and classification - a discussion based on a case study

Energy Technology Data Exchange (ETDEWEB)

Miranda, Carlos A. de J.; Faloppa, Altair A.; Mattar Neto, Miguel; Fainer, Gerson, E-mail: cmiranda@ipen.b, E-mail: afaloppa@ipen.b, E-mail: mmattar@ipen.b, E-mail: gfainer@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The ASME code, specially in its Nuclear Division (Subsection NB - Class I Components), gives some recommendations to the structural analyst on how to perform the verifications required to prove the design as good as the by-analysis prevented failures modes. Each of these failure modes has specific stress limits which are established based on simple but conservative hypothesis like the material perfectly plastic behavior and the shell theory with its typical membrane and bending stresses with linear distribution along the thickness. Other detail to keep in mind is the code distinction between primary and secondary stresses (respectively, stress that came due to equilibrium and due to displacement compatibility). In general, the numerical models used in the analyses are developed with plane or 3D solid elements and due this fact no direct comparison with the code limits can be done and, besides that, the programs do not distinguish between primary and secondary stresses. Mostly, the later are produced due to the temperature variation but they also appear near discontinuities. Sometimes, this classification is not so clear or direct. To perform the required ASME Code verifications the analyst should obtain the membrane and bending stresses from the plane or 3-D model which is called stress linearization and, also, should classify them as primary and secondary. (The excess between the maximum stress at a point and the sum of these linearized values is called peak stress and is included in the fatigue verification.) This task, most of the time is not a simple one due to the nature of the involved load and/or the complex geometry under analysis. In fact, there are several studies discussing on how to perform these stress classification and linearization. The present paper shows a discussion on how to perform these verifications based on a generic geometry found in many plants, from petrochemical to nuclear, which emphasizes some of theses issues. (author)

The Flipped Journal Club

OpenAIRE

Bounds, Richard; Boone, Stephen

2018-01-01

Introduction: Educators struggle to develop a journal club format that promotes active participation from all levels of trainees. The explosion of social media compels residencies to incorporate the evaluation and application of these resources into evidence-based practice. We sought to design an innovative “flipped journal club” to achieve greater effectiveness in meeting goals and objectives among residents and faculty. Methods: Each journal club is focused o...

Applicability of ASME sections III and VIII and of B31.1 and B31.3 to DOE facilities

International Nuclear Information System (INIS)

Antaki, G.A.

1993-01-01

DOE order 6430.1A Section 1300-3.2 requires that open-quotes....safety class items shall be designed to the ASME Boiler and Pressure Vessel Code (ASME Section III) or to other comparable safety-related codes and standards...close quotes. This requirement raises a host of technical and practical questions which, to the author's knowledge, have not been fully addressed in the past. This paper attempts to cover the following essential points, in order: Evolution of industry reference codes, Code scope, Safety margins, Logistical considerations, Costs, Backfit considerations. These points are covered in the context of a reference safety class piping and vessel system at a DOE facility which processes radioactive fluids, and which this paper calls the open-quotes reference DOE nuclear facilityclose quotes. In the conclusion, the author proposes three alternatives for code applicability which are ranked technically as open-quotes goodclose quotes, open-quotes closer to 6430.1Aclose quotes and open-quotes closest to 6430.1Aclose quotes. It is however questionable whether the alternatives which are labeled open-quotes closerclose quotes and open-quotes closestclose quotes are practically viable, as will be discussed

Journal of Pharmacy & Bioresources: Journal Sponsorship

African Journals Online (AJOL)

Journal of Pharmacy & Bioresources: Journal Sponsorship. Journal Home > About the Journal > Journal of Pharmacy & Bioresources: Journal Sponsorship. Log in or Register to get access to full text downloads.

Update and Improve Subsection NH - Alternative Simplified Creep-Fatigue Design Methods

International Nuclear Information System (INIS)

Asayama, Tai

2009-01-01

This report described the results of investigation on Task 10 of DOE/ASME Materials NGNP/Generation IV Project based on a contract between ASME Standards Technology, LLC (ASME ST-LLC) and Japan Atomic Energy Agency (JAEA). Task 10 is to Update and Improve Subsection NH -- Alternative Simplified Creep-Fatigue Design Methods. Five newly proposed promising creep-fatigue evaluation methods were investigated. Those are (1) modified ductility exhaustion method, (2) strain range separation method, (3) approach for pressure vessel application, (4) hybrid method of time fraction and ductility exhaustion, and (5) simplified model test approach. The outlines of those methods are presented first, and predictability of experimental results of these methods is demonstrated using the creep-fatigue data collected in previous Tasks 3 and 5. All the methods (except the simplified model test approach which is not ready for application) predicted experimental results fairly accurately. On the other hand, predicted creep-fatigue life in long-term regions showed considerable differences among the methodologies. These differences come from the concepts each method is based on. All the new methods investigated in this report have advantages over the currently employed time fraction rule and offer technical insights that should be thought much of in the improvement of creep-fatigue evaluation procedures. The main points of the modified ductility exhaustion method, the strain range separation method, the approach for pressure vessel application and the hybrid method can be reflected in the improvement of the current time fraction rule. The simplified mode test approach would offer a whole new advantage including robustness and simplicity which are definitely attractive but this approach is yet to be validated for implementation at this point. Therefore, this report recommends the following two steps as a course of improvement of NH based on newly proposed creep-fatigue evaluation

Students’ Learning through Reflective Journaling

OpenAIRE

Alvyda Liuolienė; Regina Metiūnienė

2011-01-01

The aim of the article is to get acquainted with the types of journals used in education to help students to learn. The paper presents some ways of fostering student’s learning through reflective journaling. It also describes the key aspects of a new method ARRIVE cycle in connection with teachers preparation to use reflective journals in a classroom. The article also presents self-assessment in reflective journaling and students’ need to self-evaluate their learning process. Reflective journ...

News from the Library: A new key reference work for the engineer: ASME's Boiler and Pressure Vessel Code at the CERN Library

CERN Multimedia

CERN Library

2011-01-01

The Library is aiming at offering a range of constantly updated reference books, to cover all areas of CERN activity. A recent addition to our collections strengthens our offer in the Engineering field.   The CERN Library now holds a copy of the complete ASME Boiler and Pressure Vessel Code, 2010 edition. This code establishes rules of safety governing the design, fabrication, and inspection of boilers and pressure vessels, and nuclear power plant components during construction. This document is considered worldwide as a reference for mechanical design and is therefore important for the CERN community. The Code published by ASME (American Society of Mechanical Engineers) is kept current by the Boiler and Pressure Committee, a volunteer group of more than 950 engineers worldwide. The Committee meets regularly to consider requests for interpretations, revision, and to develop new rules. The CERN Library receives updates and includes them in the volumes until the next edition, which is expected to ...

Students’ Learning through Reflective Journaling

Directory of Open Access Journals (Sweden)

Alvyda Liuolienė

2011-04-01

Full Text Available The aim of the article is to get acquainted with the types of journals used in education to help students to learn. The paper presents some ways of fostering student’s learning through reflective journaling. It also describes the key aspects of a new method ARRIVE cycle in connection with teachers preparation to use reflective journals in a classroom. The article also presents self-assessment in reflective journaling and students’ need to self-evaluate their learning process. Reflective journaling as central to students’ self-evaluation is described as a means of fostering metacognition.

Application of the ASME code in designing containment vessels for packages used to transport radioactive materials

International Nuclear Information System (INIS)

Raske, D.T.; Wang, Z.

1992-01-01

The primary concern governing the design of shipping packages containing radioactive materials is public safety during transport. When these shipments are within the regulatory jurisdiction of the US Department of Energy, the recommended design criterion for the primary containment vessel is either Section III or Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code, depending on the activity of the contents. The objective of this paper is to discuss the design of a prototypic containment vessel representative of a packaging for the transport of high-level radioactive material

Production of a small-circulation medical journal using desktop publishing methods.

Science.gov (United States)

Peters, B A

1994-07-01

Since its inception in January 1988, the Baylor University Medical Center Proceedings, a quarterly medical journal, has been published by the few staff of the Scientific Publications Office (Baylor Research Institute, Dallas, Texas, USA) using microcomputers and page-makeup software in conjunction with a commercial printing company. This article outlines the establishment of the journal; the steps used in the publication process; the software and hardware used; and the changes in design, content, and circulation that have taken place as the journal and the technology used to create it have evolved.

Reporting on methods of subgroup analysis in clinical trials: a survey of four scientific journals

Directory of Open Access Journals (Sweden)

E.D. Moreira Jr.

2001-11-01

Full Text Available Results of subgroup analysis (SA reported in randomized clinical trials (RCT cannot be adequately interpreted without information about the methods used in the study design and the data analysis. Our aim was to show how often inaccurate or incomplete reports occur. First, we selected eight methodological aspects of SA on the basis of their importance to a reader in determining the confidence that should be placed in the author's conclusions regarding such analysis. Then, we reviewed the current practice of reporting these methodological aspects of SA in clinical trials in four leading journals, i.e., the New England Journal of Medicine, the Journal of the American Medical Association, the Lancet, and the American Journal of Public Health. Eight consecutive reports from each journal published after July 1, 1998 were included. Of the 32 trials surveyed, 17 (53% had at least one SA. Overall, the proportion of RCT reporting a particular methodological aspect ranged from 23 to 94%. Information on whether the SA preceded/followed the analysis was reported in only 7 (41% of the studies. Of the total possible number of items to be reported, NEJM, JAMA, Lancet and AJPH clearly mentioned 59, 67, 58 and 72%, respectively. We conclude that current reporting of SA in RCT is incomplete and inaccurate. The results of such SA may have harmful effects on treatment recommendations if accepted without judicious scrutiny. We recommend that editors improve the reporting of SA in RCT by giving authors a list of the important items to be reported.

Study of Dimple Effect on the Friction Characteristics of a Journal Bearing using Taguchi Method

Science.gov (United States)

Murthy, A. Amar; Raghunandana, Dr.

2018-02-01

The effect of producing dimples using chemically etched techniques or by machining process on the surface of a journal bearing bushing to reduce the friction using Taguchi method is investigated. The data used in the present analysis is based on the results obtained by the series of experiments conducted to study the dimples effect on the Stribeck curve. It is statistically proved that producing dimples on the bushing surface of a journal bearing has significant effect on the friction coefficient when used with light oils. Also it is seen that there is an interaction effect between speeds-load and load-dimples. Hence the interaction effect, which are usually neglected should be considered during actual experiments that significantly contributes in reducing the friction in mixed lubrication regime. The experiments, if were conducted after Taguchi method, then the number of experiments would have been reduced to half of the actual set of experiments that were essentially conducted.

Avaliação do programa de atenção a crianças asmáticas acompanhadas nas unidades de saúde do Município do Embu, São Paulo, no período de 1988 a 1993

Directory of Open Access Journals (Sweden)

Renato Nabas Ventura

Full Text Available Com o objetivo de avaliar o desempenho do Programa de Atenção a Crianças Portadoras de "Chiado no Peito", no Município de Embu, São Paulo, foram estudadas 434 crianças e adolescentes de zero a 14 anos, admitidas no programa de maio/88 a julho/93. Mais de 90% desses pacientes nunca haviam sido acompanhados por esse motivo em serviço médico. Apenas 6,2% foram encaminhados a outros serviços de referência durante o acompanhamento no programa. Segundo critérios clínicos, os pacientes foram classificados em: bebê chiador (21,8%, asmáticos leves (41,7%, asmáticos moderados (28,3%, asmáticos graves (7,6% e outros (0,4%. Ao se analisar o comportamento dos asmáticos moderados e graves acompanhados por mais de um ano, observou-se melhora clínica nesses dois grupos, e o que influenciou positivamente esse fato foi a maior aderência ao uso da medicação. O número de exacerbações decresceu entre os asmáticos graves, após um ano de acompanhamento regular, embora durante os 12 meses analisados tenha havido um consumo praticamente constante de medicação broncodilatadora. O abandono ocorreu em 53,2% das crianças matriculadas, principalmente nos primeiros seis meses de acompanhamento, sendo significantemente mais freqüente entre os asmáticos moderados. Concluímos que as crianças com maior aderência ao programa se beneficiaram do mesmo, apesar das dificuldades e da falta de alguns recursos medicamentosos atualmente existentes.

Avaliação do programa de atenção a crianças asmáticas acompanhadas nas unidades de saúde do Município do Embu, São Paulo, no período de 1988 a 1993

Directory of Open Access Journals (Sweden)

Ventura Renato Nabas

1998-01-01

Full Text Available Com o objetivo de avaliar o desempenho do Programa de Atenção a Crianças Portadoras de "Chiado no Peito", no Município de Embu, São Paulo, foram estudadas 434 crianças e adolescentes de zero a 14 anos, admitidas no programa de maio/88 a julho/93. Mais de 90% desses pacientes nunca haviam sido acompanhados por esse motivo em serviço médico. Apenas 6,2% foram encaminhados a outros serviços de referência durante o acompanhamento no programa. Segundo critérios clínicos, os pacientes foram classificados em: bebê chiador (21,8%, asmáticos leves (41,7%, asmáticos moderados (28,3%, asmáticos graves (7,6% e outros (0,4%. Ao se analisar o comportamento dos asmáticos moderados e graves acompanhados por mais de um ano, observou-se melhora clínica nesses dois grupos, e o que influenciou positivamente esse fato foi a maior aderência ao uso da medicação. O número de exacerbações decresceu entre os asmáticos graves, após um ano de acompanhamento regular, embora durante os 12 meses analisados tenha havido um consumo praticamente constante de medicação broncodilatadora. O abandono ocorreu em 53,2% das crianças matriculadas, principalmente nos primeiros seis meses de acompanhamento, sendo significantemente mais freqüente entre os asmáticos moderados. Concluímos que as crianças com maior aderência ao programa se beneficiaram do mesmo, apesar das dificuldades e da falta de alguns recursos medicamentosos atualmente existentes.

Effects of Induction Heat Bending Process on Microstructure and Corrosion Properties of ASME SA312 Gr.TP304 Stainless Steel Pipes

International Nuclear Information System (INIS)

Kim, Nam In; Kim, Young Sik; Kim, Kyung Soo; Chang, Hyun Young; Park, Heung Bae; Sung, Gi Ho; Sung, Gi Ho

2015-01-01

The usage of bending products recently have increased since many industries such as automobile, aerospace, shipbuilding, and chemical plants need the application of pipings. Bending process is one of the inevitable steps to fabricate the facilities. Induction heat bending is composed of compressive bending process by local heating and cooling. This work focused on the effect of induction heat bending process on the properties of ASME SA312 Gr. TP304 stainless steel pipes. Tests were performed for base metal and bended area including extrados, intrados, crown up, and down parts. Microstructure was analyzed using an optical microscope and SEM. In order to determine intergranular corrosion resistance, Double Loop Electrochemical Potentiokinetic Reactivation (DL-EPR) test and ASTM A262 practice A and C tests were done. Every specimen revealed non-metallic inclusion free under the criteria of 1.5i of the standard and the induction heat bending process did not affect the non-metallic inclusion in the alloys. Also, all the bended specimens had finer grain size than ASTM grain size number 5 corresponding to the grain sizes of the base metal and thus the grain size of the pipe bended by induction heat bending process is acceptable. Hardness of transition start, bend, and transition end areas of ASME SA312 TP304 stainless steel was a little higher than that of base metal. Intergranular corrosion behavior was determined by ASTM A262 practice A and C and DL-EPR test, and respectively step structure, corrosion rate under 0.3 mm/y, and Degree of Sensitization (DOS) of 0.001 - 0.075 % were obtained. That is, the induction heat bending process didn't affect the intergranular corrosion behavior of ASME SA312 TP304 stainless steel

JOURNAL ANALYSIS ON OPHTHALMOLOGY AND OTHERS

Directory of Open Access Journals (Sweden)

Denise de Freitas

Full Text Available Objective: To update knowledge and methods to access and view the journals included in Qualis of CAPES Medicine III, and how to measure the impact factor. Method: Document review on the attempt to verify the way Qualis uses for ranking journals cited by the post-graduate programs of Medicine III in their evaluation periods, and the impact factors obtained by journals indexing base. Results: The classification is annual and are ranking in strata ranging from A1, the highest, and A2; B1; B2; B3; B4; B5; C. The latter has zero evaluation weight. These strata take as reference the impact factor of the journals listed by the programs. The same journal can be classified into different Qualis in other areas, and this is no inconsistency, but expressed the assigned value, in each area, at that particular journal. The Impact Factor is measured using the Journal of Citation Report in Web of Knowledge website. Conclusion: Using the criteria established by WebQualis for stratification of journals there is a quality guidance of what is produced by the program and, based on it, can be made scientific comparison of program performance. Consulting the JCR is recommended because it defines exactly what is the journal's impact factor; Qualis stratifies numerical intervals and not individual journal specificity.

Selection and reporting of statistical methods to assess reliability of a diagnostic test: Conformity to recommended methods in a peer-reviewed journal

International Nuclear Information System (INIS)

Park, Ji Eun; Sung, Yu Sub; Han, Kyung Hwa

2017-01-01

To evaluate the frequency and adequacy of statistical analyses in a general radiology journal when reporting a reliability analysis for a diagnostic test. Sixty-three studies of diagnostic test accuracy (DTA) and 36 studies reporting reliability analyses published in the Korean Journal of Radiology between 2012 and 2016 were analyzed. Studies were judged using the methodological guidelines of the Radiological Society of North America-Quantitative Imaging Biomarkers Alliance (RSNA-QIBA), and COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN) initiative. DTA studies were evaluated by nine editorial board members of the journal. Reliability studies were evaluated by study reviewers experienced with reliability analysis. Thirty-one (49.2%) of the 63 DTA studies did not include a reliability analysis when deemed necessary. Among the 36 reliability studies, proper statistical methods were used in all (5/5) studies dealing with dichotomous/nominal data, 46.7% (7/15) of studies dealing with ordinal data, and 95.2% (20/21) of studies dealing with continuous data. Statistical methods were described in sufficient detail regarding weighted kappa in 28.6% (2/7) of studies and regarding the model and assumptions of intraclass correlation coefficient in 35.3% (6/17) and 29.4% (5/17) of studies, respectively. Reliability parameters were used as if they were agreement parameters in 23.1% (3/13) of studies. Reproducibility and repeatability were used incorrectly in 20% (3/15) of studies. Greater attention to the importance of reporting reliability, thorough description of the related statistical methods, efforts not to neglect agreement parameters, and better use of relevant terminology is necessary

Selection and reporting of statistical methods to assess reliability of a diagnostic test: Conformity to recommended methods in a peer-reviewed journal

Energy Technology Data Exchange (ETDEWEB)

Park, Ji Eun; Sung, Yu Sub [Dept. of Radiology and Research Institute of Radiology, University of Ulsan College of Medicine, Asan Medical Center, Seoul (Korea, Republic of); Han, Kyung Hwa [Dept. of Radiology, Research Institute of Radiological Science, Yonsei University College of Medicine, Seoul (Korea, Republic of); and others

2017-11-15

To evaluate the frequency and adequacy of statistical analyses in a general radiology journal when reporting a reliability analysis for a diagnostic test. Sixty-three studies of diagnostic test accuracy (DTA) and 36 studies reporting reliability analyses published in the Korean Journal of Radiology between 2012 and 2016 were analyzed. Studies were judged using the methodological guidelines of the Radiological Society of North America-Quantitative Imaging Biomarkers Alliance (RSNA-QIBA), and COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN) initiative. DTA studies were evaluated by nine editorial board members of the journal. Reliability studies were evaluated by study reviewers experienced with reliability analysis. Thirty-one (49.2%) of the 63 DTA studies did not include a reliability analysis when deemed necessary. Among the 36 reliability studies, proper statistical methods were used in all (5/5) studies dealing with dichotomous/nominal data, 46.7% (7/15) of studies dealing with ordinal data, and 95.2% (20/21) of studies dealing with continuous data. Statistical methods were described in sufficient detail regarding weighted kappa in 28.6% (2/7) of studies and regarding the model and assumptions of intraclass correlation coefficient in 35.3% (6/17) and 29.4% (5/17) of studies, respectively. Reliability parameters were used as if they were agreement parameters in 23.1% (3/13) of studies. Reproducibility and repeatability were used incorrectly in 20% (3/15) of studies. Greater attention to the importance of reporting reliability, thorough description of the related statistical methods, efforts not to neglect agreement parameters, and better use of relevant terminology is necessary.

Assessment of crack-like flaws - Comparison of procedures in BS 7910, API 579-1/ASME FFS-1, RSE-M AND FITNET

International Nuclear Information System (INIS)

Chaudouet, A.

2007-01-01

Among all Fitness For Service Codes enabling to assess flaws in metallic structures and to evaluate their remaining life, new editions of the most important ones at the international level have been issued recently. The latest edition of BS 7910 in United Kingdom has been released in October 2005. In the USA, API and ASME have edited a new standard in 2007, API579-1/ASME FFS-1, dedicated to pressure equipment. In France, the rules concerning the of Light Water Reactors, RSE-M, have been updated in 2005. Finally, in Europe, the FITNET network is writing a document based on BS 7910 but extended with the most recent results in this domain. Rules given in these documents to assess crack-like flaws with respect to fracture and fatigue propagation are presented. They are compared in order to point out the most interesting aspects of each ones and to identify those which could be generalized. An example assessed with the above mentioned 'Codes' enlightens the differences in the results with respect to the 'Code' used. (author) [fr

Journalism studies in Nederland: een inventarisatie

NARCIS (Netherlands)

Brants, K.; Vasterman, P.

2010-01-01

This article presents the results of a survey among journalism studies researchers from universities and schools of journalism in the Netherlands. It shows the themes they focus on, what they publish about, in what journals, books and book chapters, in what language, and what methods they generally

Interactive overlays: a new method for generating global journal maps from Web-of-Science data

NARCIS (Netherlands)

Leydesdorff, L.; Rafols, I.

2012-01-01

Recent advances in methods and techniques enable us to develop interactive overlays to a global map of science based on aggregated citation relations among the 9162 journals contained in the Science Citation Index and Social Science Citation Index 2009. We first discuss the pros and cons of the

Conflicts of interest at medical journals

DEFF Research Database (Denmark)

Lundh, Andreas; Barbateskovic, Marija; Hróbjartsson, Asbjørn

2010-01-01

for journals. We investigated industry-supported trials' influence on journal impact factors and revenue. METHODS AND FINDINGS: we sampled six major medical journals (Annals of Internal Medicine, Archives of Internal Medicine, BMJ, JAMA, The Lancet, and New England Journal of Medicine [NEJM]). For each journal......BACKGROUND: transparency in reporting of conflict of interest is an increasingly important aspect of publication in medical journals. Publication of large industry-supported trials may generate many citations and journal income through reprint sales and thereby be a source of conflicts of interest......, we identified randomised trials published in 1996-1997 and 2005-2006 using PubMed, and categorized the type of financial support. Using Web of Science, we investigated citations of industry-supported trials and the influence on journal impact factors over a ten-year period. We contacted journal...

Progress in Developing Finite Element Models Replicating Flexural Graphite Testing

International Nuclear Information System (INIS)

Bratton, Robert

2010-01-01

This report documents the status of flexural strength evaluations from current ASTM procedures and of developing finite element models predicting the probability of failure. This work is covered under QLD REC-00030. Flexural testing procedures of the American Society for Testing and Materials (ASTM) assume a linear elastic material that has the same moduli for tension and compression. Contrary to this assumption, graphite is known to have different moduli for tension and compression. A finite element model was developed and demonstrated that accounts for the difference in moduli tension and compression. Brittle materials such as graphite exhibit significant scatter in tensile strength, so probabilistic design approaches must be used when designing components fabricated from brittle materials. ASTM procedures predicting probability of failure in ceramics were compared to methods from the current version of the ASME graphite core components rules predicting probability of failure. Using the ASTM procedures yields failure curves at lower applied forces than the ASME rules. A journal paper was published in the Journal of Nuclear Engineering and Design exploring the statistical models of fracture in graphite.

Fast and accurate semi-automated segmentation method of spinal cord MR images at 3T applied to the construction of a cervical spinal cord template.

Directory of Open Access Journals (Sweden)

Mohamed-Mounir El Mendili

Full Text Available To design a fast and accurate semi-automated segmentation method for spinal cord 3T MR images and to construct a template of the cervical spinal cord.A semi-automated double threshold-based method (DTbM was proposed enabling both cross-sectional and volumetric measures from 3D T2-weighted turbo spin echo MR scans of the spinal cord at 3T. Eighty-two healthy subjects, 10 patients with amyotrophic lateral sclerosis, 10 with spinal muscular atrophy and 10 with spinal cord injuries were studied. DTbM was compared with active surface method (ASM, threshold-based method (TbM and manual outlining (ground truth. Accuracy of segmentations was scored visually by a radiologist in cervical and thoracic cord regions. Accuracy was also quantified at the cervical and thoracic levels as well as at C2 vertebral level. To construct a cervical template from healthy subjects' images (n=59, a standardization pipeline was designed leading to well-centered straight spinal cord images and accurate probability tissue map.Visual scoring showed better performance for DTbM than for ASM. Mean Dice similarity coefficient (DSC was 95.71% for DTbM and 90.78% for ASM at the cervical level and 94.27% for DTbM and 89.93% for ASM at the thoracic level. Finally, at C2 vertebral level, mean DSC was 97.98% for DTbM compared with 98.02% for TbM and 96.76% for ASM. DTbM showed similar accuracy compared with TbM, but with the advantage of limited manual interaction.A semi-automated segmentation method with limited manual intervention was introduced and validated on 3T images, enabling the construction of a cervical spinal cord template.

Fast and accurate semi-automated segmentation method of spinal cord MR images at 3T applied to the construction of a cervical spinal cord template.

Science.gov (United States)

El Mendili, Mohamed-Mounir; Chen, Raphaël; Tiret, Brice; Villard, Noémie; Trunet, Stéphanie; Pélégrini-Issac, Mélanie; Lehéricy, Stéphane; Pradat, Pierre-François; Benali, Habib

2015-01-01

To design a fast and accurate semi-automated segmentation method for spinal cord 3T MR images and to construct a template of the cervical spinal cord. A semi-automated double threshold-based method (DTbM) was proposed enabling both cross-sectional and volumetric measures from 3D T2-weighted turbo spin echo MR scans of the spinal cord at 3T. Eighty-two healthy subjects, 10 patients with amyotrophic lateral sclerosis, 10 with spinal muscular atrophy and 10 with spinal cord injuries were studied. DTbM was compared with active surface method (ASM), threshold-based method (TbM) and manual outlining (ground truth). Accuracy of segmentations was scored visually by a radiologist in cervical and thoracic cord regions. Accuracy was also quantified at the cervical and thoracic levels as well as at C2 vertebral level. To construct a cervical template from healthy subjects' images (n=59), a standardization pipeline was designed leading to well-centered straight spinal cord images and accurate probability tissue map. Visual scoring showed better performance for DTbM than for ASM. Mean Dice similarity coefficient (DSC) was 95.71% for DTbM and 90.78% for ASM at the cervical level and 94.27% for DTbM and 89.93% for ASM at the thoracic level. Finally, at C2 vertebral level, mean DSC was 97.98% for DTbM compared with 98.02% for TbM and 96.76% for ASM. DTbM showed similar accuracy compared with TbM, but with the advantage of limited manual interaction. A semi-automated segmentation method with limited manual intervention was introduced and validated on 3T images, enabling the construction of a cervical spinal cord template.

Technical Review on Fitness-for-Service for Buried Pipe by ASME Code Case N-806

International Nuclear Information System (INIS)

Park, Sang Kyu; Lee, Yo Seop; So, Il Su; Lim, Bu Taek

2012-01-01

Fitness-for-Service is a useful technology to determine replacement timing, next inspection timing or in-service when nuclear power plant's buried pipes are damaged. If is possible for buried pipes to be aged by material loss, cracks and occlusion as operating time goes by. Therefore Fitness-for-Service technology for buried pipe is useful for plant industry to perform replacement and repair. Fitness-for-Service for buried pipe is studied in terms of existing code and standard for Fitness-for-Service and a current developing code case. Fitness-for-Service for buried pipe was performed according to Code Case N-806 developed by ASME (American Society of Mechanical Engineers)

International Journal of Humanistic Studies: Journal Sponsorship

African Journals Online (AJOL)

International Journal of Humanistic Studies: Journal Sponsorship. Journal Home > About the Journal > International Journal of Humanistic Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

East African Journal of Statistics: Journal Sponsorship

African Journals Online (AJOL)

East African Journal of Statistics: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Statistics: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of Neurological Sciences: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Neurological Sciences: Journal Sponsorship. Journal Home > About the Journal > African Journal of Neurological Sciences: Journal Sponsorship. Log in or Register to get access to full text downloads.

Nigerian Journal of General Practice: Journal Sponsorship

African Journals Online (AJOL)

Nigerian Journal of General Practice: Journal Sponsorship. Journal Home > About the Journal > Nigerian Journal of General Practice: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of Political Science: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Political Science: Journal Sponsorship. Journal Home > About the Journal > African Journal of Political Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of AIDS Research: Journal Sponsorship

African Journals Online (AJOL)

African Journal of AIDS Research: Journal Sponsorship. Journal Home > About the Journal > African Journal of AIDS Research: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of Management Research: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Management Research: Journal Sponsorship. Journal Home > About the Journal > African Journal of Management Research: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of Infectious Diseases: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Infectious Diseases: Journal Sponsorship. Journal Home > About the Journal > African Journal of Infectious Diseases: Journal Sponsorship. Log in or Register to get access to full text downloads.

West African Journal of Radiology: Journal Sponsorship

African Journals Online (AJOL)

West African Journal of Radiology: Journal Sponsorship. Journal Home > About the Journal > West African Journal of Radiology: Journal Sponsorship. Log in or Register to get access to full text downloads.

Journal of Civil Engineering, JKUAT: Journal Sponsorship

African Journals Online (AJOL)

Journal of Civil Engineering, JKUAT: Journal Sponsorship. Journal Home > About the Journal > Journal of Civil Engineering, JKUAT: Journal Sponsorship. Log in or Register to get access to full text downloads.

New Egyptian Journal of Microbiology: Journal Sponsorship

African Journals Online (AJOL)

New Egyptian Journal of Microbiology: Journal Sponsorship. Journal Home > About the Journal > New Egyptian Journal of Microbiology: Journal Sponsorship. Log in or Register to get access to full text downloads.

Mgbakoigba: Journal of African Studies: Journal Sponsorship

African Journals Online (AJOL)

Mgbakoigba: Journal of African Studies: Journal Sponsorship. Journal Home > About the Journal > Mgbakoigba: Journal of African Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

Narrative journalism as complementary inquiry

Directory of Open Access Journals (Sweden)

Jørgen Jeppesen

2011-10-01

Full Text Available Narrative journalism is a method to craft stories worth reading about real people. In this article, we explore the ability of that communicative power to produce insights complementary to those obtainable through traditional qualitative and quantitative research methods. With examples from a study of journalistic narrative as patient involvement in professional rehabilitation, interview data transcribed as stories are analyzed for qualities of heterogeneity, sensibility, transparency, and reflexivity. Building on sociological theories of thinking with stories, writing as inquiry, and public journalism as ethnography, we suggest that narrative journalism as a common practice might unfold dimensions of subjective otherness of the self. Aspiring to unite writing in both transparently confrontational and empathetically dialogic ways, the narrative journalistic method holds a potential to expose dynamics of power within the interview.

Educational Technology Research Journals: "Journal of Research on Technology in Education," 2001-2010

Science.gov (United States)

Billings, Christopher; Nielsen, P. Lynne; Snyder, Aaron; Sorensen, Alec; West, Richard E.

2012-01-01

In this study, the authors examined the "Journal of Research on Technology in Education (JRTE)" to discover trends from 2001-2010 in the topics covered in the articles, article types (including research methods used), authorship, and citation frequency. Articles from the journal dealt mostly with PK-12 settings and focused on technology…

How to Rank Journals.

Science.gov (United States)

Bradshaw, Corey J A; Brook, Barry W

2016-01-01

There are now many methods available to assess the relative citation performance of peer-reviewed journals. Regardless of their individual faults and advantages, citation-based metrics are used by researchers to maximize the citation potential of their articles, and by employers to rank academic track records. The absolute value of any particular index is arguably meaningless unless compared to other journals, and different metrics result in divergent rankings. To provide a simple yet more objective way to rank journals within and among disciplines, we developed a κ-resampled composite journal rank incorporating five popular citation indices: Impact Factor, Immediacy Index, Source-Normalized Impact Per Paper, SCImago Journal Rank and Google 5-year h-index; this approach provides an index of relative rank uncertainty. We applied the approach to six sample sets of scientific journals from Ecology (n = 100 journals), Medicine (n = 100), Multidisciplinary (n = 50); Ecology + Multidisciplinary (n = 25), Obstetrics & Gynaecology (n = 25) and Marine Biology & Fisheries (n = 25). We then cross-compared the κ-resampled ranking for the Ecology + Multidisciplinary journal set to the results of a survey of 188 publishing ecologists who were asked to rank the same journals, and found a 0.68-0.84 Spearman's ρ correlation between the two rankings datasets. Our composite index approach therefore approximates relative journal reputation, at least for that discipline. Agglomerative and divisive clustering and multi-dimensional scaling techniques applied to the Ecology + Multidisciplinary journal set identified specific clusters of similarly ranked journals, with only Nature & Science separating out from the others. When comparing a selection of journals within or among disciplines, we recommend collecting multiple citation-based metrics for a sample of relevant and realistic journals to calculate the composite rankings and their relative uncertainty windows.

Flanged joints with contact outside the bolt circle: ASME Part B design rules

International Nuclear Information System (INIS)

Rodabaugh, E.C.; Moore, S.E.

1976-05-01

The ASME Boiler and Pressure Vessel Code, Section VIII, Division 1, gives rules which are subdivided into ''Part A'' and ''Part B''. Part A covers flanged joints where contact between flanges occurs through a gasket located inside the bolt holes. Part B covers flanged joints with contact outside the bolt holes. This report (a) summarizes the theory for Part B flanged joints, (b) presents examples which show the significant differences between Part A flanged joints and Part B flanged joints, (c) presents the available test data relevant to the characteristics of Part B flanged joints, (d) gives listings of two computer programs which can be used to evaluate the characteristics of Part B flanged joints, and (e) gives recommendations for Code revisions and other aspects of Part B flanged-joint design

Nigerian Journal of Gastroenterology and Hepatology: Journal ...

African Journals Online (AJOL)

Nigerian Journal of Gastroenterology and Hepatology: Journal Sponsorship. Journal Home > About the Journal > Nigerian Journal of Gastroenterology and Hepatology: Journal Sponsorship. Log in or Register to get access to full text downloads.

Hypothetical influence of non-indexed Spanish journals on the impact factor of radiological journals

International Nuclear Information System (INIS)

Miguel-Dasit, Alberto; Aleixandre, Rafael; Valderrama, Juan C.; Marti-Bonmati, Luis; Sanfeliu, Pilar

2005-01-01

Objective: The aim of this study was to analyze the hypothetical changes in the 2001 impact factor of 52 radiological journals included in the Science Citation Index-Journal Citation Reports by also counting cites proceeding from 73 Spanish journals on different medical specialties. Also, to estimate the possible impact factor of the official Spanish radiology journal, Radiologia, not included in this database. Materials and methods: A modified 2001 impact factor of 52 radiological journals and Radiologia was obtained by adding the number of cites in 1999 and 2000 from the medical Spanish journals. Data were obtained by consulting the 2001 edition of the Journal Citation Reports in the 'Web of Science' database. Results: The 16,985 bibliographical references were analysed (232 of them to radiological journals). The journal with the largest increase in its 2001 impact factor (from 1.83 to 1.90) was Radiologic Clinics of North America. European Journal of Radiology was the European journal with the highest increase (from 1.084 to 1.110) in the difference between the 2001 modified and original impact factor. The modified 2001 impact factor of the 34 American journals was statistically higher (P = 0.016) than that of the 18 European journals (1.64 versus 0.93). Differences between the 2001 modified and original impact factor were slightly higher in the American journals (no statistically significant difference). The 2001 impact factor of Radiologia was 0.056. Discussion: Differences between the 2001 original and modified impact factor were small, but larger in the American journals. The 2001 impact factor of Radiologia was modest, although similar to other publications included in the Journal Citation Reports

IE Information Notice No. 85-33: Undersized nozzle-to-shell welded joints in tanks and heat exchangers constructed under the rules of the ASME boiler and vessel code

International Nuclear Information System (INIS)

Jordan, E.L.

1993-01-01

During the CAT (Construction Appraisal Team) inspections conducted at the River Bend, Shearon Harris, and Braidwood nuclear power projects, the NRC identified undersized nozzle-to-shell welded joints (ASME Category D joints) in tanks and heat exchangers manufactured by various vendors. Specifically, four main steam isolation valve air accumulator tanks were found to have undersized nozzle-to-shell joints at the River Bend plant; seven tanks were found to have undersized nozzle-to-shell weld reinforcements at the Shearon Harris Station; eight tanks and two heat exchangers were found to have undersized nozzle-to-shell weld reinforcements at Braidwood Station. These tanks and heat exchangers were Code stamped and certified as being constructed in accordance with the requirements of the ASME Code. The ASME Code, Section III (NX-3352.4) requires that nozzle-to-shell welded joints have reinforcement (t c ) of 0.7t p or 1/4 inch, whichever is less, where t p is the thickness of the penetrating part. Some of the inspected welded joints did not have the minimum weld reinforcement (t c ) required by the Code. Other joints had the minimum weld reinforcement (t c ) required by the Code, but were found to be undersized with respect to the sizes specified on the applicable construction drawings

Video Journaling as a Method of Reflective Practice

Science.gov (United States)

Parikh, Sejal B.; Janson, Christopher; Singleton, Tiffany

2012-01-01

The purpose of this phenomenological study was to examine seven school counseling students' experiences of creating reflective video journals during their first internship course. Specifically, this study focused on capturing the essence of the experiences related to personal reactions, feelings, and thoughts about creating two video journal…

An abnormal situation modeling method to assist operators in safety-critical systems

International Nuclear Information System (INIS)

Naderpour, Mohsen; Lu, Jie; Zhang, Guangquan

2015-01-01

One of the main causes of accidents in safety-critical systems is human error. In order to reduce human errors in the process of handling abnormal situations that are highly complex and mentally taxing activities, operators need to be supported, from a cognitive perspective, in order to reduce their workload, stress, and the consequent error rate. Of the various cognitive activities, a correct understanding of the situation, i.e. situation awareness (SA), is a crucial factor in improving performance and reducing errors. Despite the importance of SA in decision-making in time- and safety-critical situations, the difficulty of SA modeling and assessment means that very few methods have as yet been developed. This study confronts this challenge, and develops an innovative abnormal situation modeling (ASM) method that exploits the capabilities of risk indicators, Bayesian networks and fuzzy logic systems. The risk indicators are used to identify abnormal situations, Bayesian networks are utilized to model them and a fuzzy logic system is developed to assess them. The ASM method can be used in the development of situation assessment decision support systems that underlie the achievement of SA. The performance of the ASM method is tested through a real case study at a chemical plant. - Highlights: • Bayesian networks are applied to represent operators’ mental models when confront with abnormal situations. • A fuzzy logic system is used to resemble operators’ generating assessment results for every abnormal situation. • A virtual plant user interface and a prototype based on proposed method are developed to simulate a real case

International Journal of Health Research

African Journals Online (AJOL)

Erah

The International Journal of Health Research is an online international journal allowing ... forum for the communication and evaluation of data, methods and findings in health sciences and related ... Conclusion: Permeation rate of drugs across the ..... New Delhi, McGraw Hill Medical Publishing ... Human skin permeation of.

Higher education journals as didactic frameworks

DEFF Research Database (Denmark)

Keiding, Tina Bering; Qvortrup, Ane

2018-01-01

topics. Students as participants and learners are a frequent topic in especially one journal, but receive little attention in the other journals. Also, educational technologies receive a varying degree of attention across the journals. Based on the mapping, this article discusses Higher Education......During the last 20 years, we have witnessed a growing interest in research in teaching, learning and educational development in higher education (HE). The result is that ‘Higher Education Didactics’ has established itself as a research field in its own right. This article explores Higher Education...... influential, while the others stem from the Anglo-Saxon curriculum tradition. The mapping shows that all journals are strongly occupied with teaching methods, especially methods grounded in theories of active and social learning. In contrast, didactic categories such as goal, content and assessment are rare...

Are claims made in orthodontic journal advertisements evidence-supported?

NARCIS (Netherlands)

Livas, Christos; Kouskoura, Thaleia; Ren, Yijin; Katsaros, Christos; Pandis, Nikolaos

Objective: To examine the supporting evidence of advertisements published in six leading orthodontic journals. Materials and Methods: The 2012-2013 printed issues of American Journal of Orthodontics and Dentofacial Orthopedics, Australian Orthodontic Journal, Journal of Orthodontics, European

Teaching Civic Journalism: Integrating Theory and Practice.

Science.gov (United States)

McDevitt, Michael

2000-01-01

Describes a journalism course that used an integrative approach to teaching about the principles, practice, and effects of civic journalism, combining theory, news writing, and evaluation. Describes the class project on the controversial issue of panhandling. Discusses goals of civic journalism and of the project, journalistic methods used,…

instU_3d_asm_Cp: MERRA 3D IAU State, Meteorology Diurnal 1.25 x 1.25 degree V5.2.0 (MAIUCPASM) at GES DISC

Data.gov (United States)

National Aeronautics and Space Administration — The MAIUCPASM or instU_3d_asm_Cp data product is the MERRA Data Assimilation System 3-Dimensional assimilated state on pressure, at a reduced resolution. It is a...

African Journal of Finance and Management: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Finance and Management: Journal Sponsorship. Journal Home > About the Journal > African Journal of Finance and Management: Journal Sponsorship. Log in or Register to get access to full text downloads.

Scopus: Journal of East African Ornithology: Journal Sponsorship

African Journals Online (AJOL)

Scopus: Journal of East African Ornithology: Journal Sponsorship. Journal Home > About the Journal > Scopus: Journal of East African Ornithology: Journal Sponsorship. Log in or Register to get access to full text downloads.

East African Journal of Public Health: Journal Sponsorship

African Journals Online (AJOL)

East African Journal of Public Health: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Public Health: Journal Sponsorship. Log in or Register to get access to full text downloads.

Science, Technology and Arts Research Journal: Journal Sponsorship

African Journals Online (AJOL)

Science, Technology and Arts Research Journal: Journal Sponsorship. Journal Home > About the Journal > Science, Technology and Arts Research Journal: Journal Sponsorship. Log in or Register to get access to full text downloads.

African Journal of Oral Health Sciences: Journal Sponsorship

African Journals Online (AJOL)

African Journal of Oral Health Sciences: Journal Sponsorship. Journal Home > About the Journal > African Journal of Oral Health Sciences: Journal Sponsorship. Log in or Register to get access to full text downloads.

South African Journal of Sports Medicine: Journal Sponsorship

African Journals Online (AJOL)

South African Journal of Sports Medicine: Journal Sponsorship. Journal Home > About the Journal > South African Journal of Sports Medicine: Journal Sponsorship. Log in or Register to get access to full text downloads.

Journal of History and Diplomatic Studies: Journal Sponsorship

African Journals Online (AJOL)

Journal of History and Diplomatic Studies: Journal Sponsorship. Journal Home > About the Journal > Journal of History and Diplomatic Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

West African Journal of Applied Ecology: Journal Sponsorship

African Journals Online (AJOL)

West African Journal of Applied Ecology: Journal Sponsorship. Journal Home > About the Journal > West African Journal of Applied Ecology: Journal Sponsorship. Log in or Register to get access to full text downloads.

The role of qualitative research in psychological journals.

Science.gov (United States)

Kidd, Sean A

2002-03-01

The acceptance of qualitative research in 15 journals published and distributed by the American Psychological Association (APA) was investigated. This investigation included a PsycINFO search using the keyword qualitative, an analysis of 15 APA journals for frequency of qualitative publication, a content analysis of the journal descriptions, and the results of qualitative interviews with 10 of the chief editors of those journals. The results indicate that there exists a substantial amount of interest in the potential contribution of qualitative methods in major psychological journals, although this interest is not ubiquitous, well defined, or communicated. These findings highlight the need for APA to state its position regarding the applicability of qualitative methods in the study of psychology.

New Egyptian Journal of Microbiology: About this journal

African Journals Online (AJOL)

New Egyptian Journal of Microbiology: About this journal. Journal Home > New Egyptian Journal of Microbiology: About this journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue ...

Calculation methods for externally pressurised (hydrostatic) journal bearings with capillary restrictor control

Science.gov (United States)

1992-09-01

ESDU 92026 provides a procedure for the design and performance analysis of the bearings with five or more identical equally-spaced rectangular recesses (or pockets) fed by identical capillary restrictors from a constant pressure supply. The method takes account of stiffness and overload capacity requirements and determines the bearing overall size and proportions from the required load, speed and shaft diameter, recommends the clearance and supply pressure, and defines the recess dimensions and capillary restrictor size from the properties of the chosen lubricant. Equations and charts allow prediction of the journal displacement under load, the power loss, the lubricant flow rate, and the bearing and lubricant temperatures. The method applies to laminar flow and guidance is given for assessing the onset of non-laminar flow in the bearing and restrictors. Guidance is also given on the likelihood of bearing-induced instability. The user is assisted by flowcharts in applying the method, and two practical worked examples illustrate the procedure. ESDU 92037 introduces a FORTRAN program that implements the method, and magnetic media are available in ESDUpac A9237.

International Journal of Development and Policy Studies: Journal ...

African Journals Online (AJOL)

International Journal of Development and Policy Studies: Journal Sponsorship. Journal Home > About the Journal > International Journal of Development and Policy Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

Western Indian Ocean Journal of Marine Science: Journal ...

African Journals Online (AJOL)

Western Indian Ocean Journal of Marine Science: Journal Sponsorship. Journal Home > About the Journal > Western Indian Ocean Journal of Marine Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

Lagos Journal of Library and Information Science: Journal ...

African Journals Online (AJOL)

Lagos Journal of Library and Information Science: Journal Sponsorship. Journal Home > About the Journal > Lagos Journal of Library and Information Science: Journal Sponsorship. Log in or Register to get access to full text downloads.

Tanzania Journal of Forestry and Nature Conservation: Journal ...

African Journals Online (AJOL)

Tanzania Journal of Forestry and Nature Conservation: Journal Sponsorship. Journal Home > About the Journal > Tanzania Journal of Forestry and Nature Conservation: Journal Sponsorship. Log in or Register to get access to full text downloads.

Application of the ASME code in the design of the GA-4 and GA-9 casks

International Nuclear Information System (INIS)

Mings, W.J.; Koploy, M.A.

1992-01-01

General Atomics (GA) is developing two spent fuel shipping casks for transport by legal weight truck (LWT). The casks are designed to the loading, environmental conditions and safety requirements defined in Title 10 of the Code of Federal Regulations, Part 71 (10CFR71). To ensure that all components of the cask meet the 10CFR71 rules, GA established structural design criteria for each component based on NRC Regulatory Guides and the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code). This paper discusses the criteria used for different cask components, how they were applied and the conservatism and safety margins built into the criteria and assumption

Evaluation of the integrity of reactor vessels designed to ASME Code, Sections I and/or VIII

International Nuclear Information System (INIS)

Hoge, K.G.

1976-01-01

A documented review of nuclear reactor pressure vessels designed to ASME Code, Sections I and/or VIII is made. The review is primarily concerned with the design specifications and quality assurance programs utilized for the reactor vessel construction and the status of power plant material surveillance programs, pressure-temperature operating limits, and inservice inspection programs. The following ten reactor vessels for light-water power reactors are covered in the report: Indian Point Unit No. 1, Dresden Unit No. 1, Yankee Rowe, Humboldt Bay Unit No. 3, Big Rock Point, San Onofre Unit No. 1, Connecticut Yankee, Oyster Creek, Nine Mile Point Unit No. 1, and La Crosse

Journal of Genetics | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Genetics. James F. Crow. Articles written in Journal of Genetics. Volume 87 Issue 4 December 2008 pp 349-353 Perspectives. Maintaining evolvability · James F. Crow · More Details Abstract Fulltext PDF. Although molecular methods, such as QTL mapping, have revealed a number of loci with ...

BrowZine: A Method for Managing a Personalized Collection of Journals.

Science.gov (United States)

Swogger, Susan E; Linares, Brenda M

2016-01-01

BrowZine is a mobile application and web service that helps users create their own personalized library/collection of journals. This column will showcase some special features of this app and describe its format and capabilities for mobile devices. BrowZine enables users to organize and manage journals and articles that are commonly read in their field and disciplines in order to track and keep abreast of new research.

[Quantitative analysis of the structure of neuronal dendritic spines in the striatum using the Leitz-ASM system].

Science.gov (United States)

Leontovich, T A; Zvegintseva, E G

1985-10-01

Two principal classes of striatum long axonal neurons (sparsely ramified reticular cells and densely ramified dendritic cells) were analyzed quantitatively in four animal species: hedgehog, rabbit, dog and monkey. The cross section area, total dendritic length and the area of dendritic field were measured using "LEITZ-ASM" system. Classes of neurons studied were significantly different in dogs and monkeys, while no differences were noted between hedgehog and rabbit. Reticular neurons of different species varied much more than dendritic ones. Quantitative analysis has revealed the progressive increase in the complexity of dendritic tree in mammals from rabbit to monkey.

TOC: Table of Contents Practices of Primary Journals--Recommendations for Monolingual, Multilingual and International Journals.

Science.gov (United States)

Juhasz, Stephen; And Others

Table of contents (TOC) practices of some 120 primary journals were analyzed. The journals were randomly selected. The method of randomization is described. The samples were selected from a university library with a holding of approximately 12,000 titles published worldwide. A questionnaire was designed. Purpose was to find uniformity and…

Journal of Biosciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Biosciences. Sangappa. Articles written in Journal of Biosciences. Volume 30 Issue 2 March 2005 pp 259-268 Articles. Crystal structure of raw pure Mysore silk fibre based on (Ala-Gly)2-Ser-Gly peptide sequence using Linked-Atom-Least-Squares method · Sangappa S S Mahesh R Somashekar.

Modeling Nitrous Oxide Production during Biological Nitrogen Removal via Nitrification and Denitrification: Extensions to the General ASM Models

DEFF Research Database (Denmark)

Ni, Bing-Jie; Ruscalleda, Maël; Pellicer i Nàcher, Carles

2011-01-01

on N2O production from four different mixed culture nitrification and denitrification reactor study reports. Modeling results confirm that hydroxylamine oxidation by ammonium oxidizers (AOB) occurs 10 times slower when NO2– participates as final electron acceptor compared to the oxic pathway. Among......Nitrous oxide (N2O) can be formed during biological nitrogen (N) removal processes. In this work, a mathematical model is developed that describes N2O production and consumption during activated sludge nitrification and denitrification. The well-known ASM process models are extended to capture N2O...

A Computer-Aided Bibliometrics System for Journal Citation Analysis and Departmental Core Journal Ranking List Generation

Directory of Open Access Journals (Sweden)

Yih-Chearng Shiue

2004-12-01

Full Text Available Due to the tremendous increase and variation in serial publications, faculties in department of university are finding it difficult to generate and update their departmental core journal list regularly and accurately, and libraries are finding it difficult to maintain their current serial collection for different departments. Therefore, the evaluation of a departmental core journal list is an important task for departmental faculties and librarians. A departmental core journal list not only helps departments understand research performances of faculties and students, but also helps librarians make decisions about which journals to retain and which to cancel. In this study, a Computer-Aided Bibliometrics System was implemented and two methodologies (JCDF and LibJF were proposed in order to generate a departmental core journal ranking list and make the journal citation analysis. Six departments were taken as examples, with MIS as the major one. One journal citation pattern was found and the ratio of Turning point-to-No. journal was always around 0.07 among the 10 journals and 6 departments. After comparing with four methodologies via overlapping rate and standard deviation distances, the two proposed methodologies were shown to be better than questionnaire and library subscription method.

International Journal of Humanistic Studies: About this journal

African Journals Online (AJOL)

International Journal of Humanistic Studies: About this journal. Journal Home > International Journal of Humanistic Studies: About this journal. Log in or Register to get access to full text downloads.

Tropical Journal of Pharmaceutical Research: About this journal

African Journals Online (AJOL)

Tropical Journal of Pharmaceutical Research: About this journal. Journal Home > Tropical Journal of Pharmaceutical Research: About this journal. Log in or Register to get access to full text downloads.

Nigerian Journal of Pharmaceutical Research: About this journal

African Journals Online (AJOL)

Nigerian Journal of Pharmaceutical Research: About this journal. Journal Home > Nigerian Journal of Pharmaceutical Research: About this journal. Log in or Register to get access to full text downloads.

Detecting Hijacked Journals by Using Classification Algorithms.

Science.gov (United States)

Andoohgin Shahri, Mona; Jazi, Mohammad Davarpanah; Borchardt, Glenn; Dadkhah, Mehdi

2018-04-01

Invalid journals are recent challenges in the academic world and many researchers are unacquainted with the phenomenon. The number of victims appears to be accelerating. Researchers might be suspicious of predatory journals because they have unfamiliar names, but hijacked journals are imitations of well-known, reputable journals whose websites have been hijacked. Hijacked journals issue calls for papers via generally laudatory emails that delude researchers into paying exorbitant page charges for publication in a nonexistent journal. This paper presents a method for detecting hijacked journals by using a classification algorithm. The number of published articles exposing hijacked journals is limited and most of them use simple techniques that are limited to specific journals. Hence we needed to amass Internet addresses and pertinent data for analyzing this type of attack. We inspected the websites of 104 scientific journals by using a classification algorithm that used criteria common to reputable journals. We then prepared a decision tree that we used to test five journals we knew were authentic and five we knew were hijacked.

Good journalism or peace journalism?

OpenAIRE

David Loyn

2007-01-01

This paper argues against the prescriptive notions of Peace Journalism, and in particular its exclusive nature and attempt to define itself as a new orthodoxy. Most of the paper is a critique of the work of Jake Lynch and Annabel McGoldrick, in a book published in 2005, as well as their earlier Reporting the World series. They condemn all other ways of reporting as 'War Journalism, biased in favour of war.' I argue instead that the opposite of Peace Journalism is good journalism. Much of ...

Accelerator system model (ASM): A unique tool in exploring accelerator driven transmutation technologies (ADTT) system trade space

Energy Technology Data Exchange (ETDEWEB)

Myers, T.J.; Favale, A.J.; Berwald, D.H.; Burger, E.C.; Paulson, C.C.; Peacock, M.A.; Piaszczyk, C.M.; Piechowiak, E.M.; Rathke, J.W. [Northrop Grumman Corp., Bethpage, NY (United States). Advanced Technology and Development Center

1997-09-01

To aid in the development and optimization of emerging Accelerator Driven Transmutation Technology (ADTT) concepts, the Northrop Grumman Corporation, working together with G.H. Gillespie Associates and Los Alamos National Laboratory has developed a computational tool which combines both accelerator physics layout/analysis capabilities with engineering analysis capabilities to create a standardized platform to compare and contrast accelerator system configurations. In this context, the accelerator system configuration includes not only the accelerating structures, but also the major support systems such as the vacuum, thermal control, RF power, and cryogenic subsystem (if superconducting accelerator operation is investigated) as well as estimates of the costs for enclosures (accelerating tunnel and RF halls). This paper presents an overview of the Accelerator System Model (ASM) code flow, as well as a discussion of the data and analysis upon which it is based. Also presented is material which addresses the development of the evaluation criteria employed by this code including a presentation of the economic analysis methods, and a discussion of the cost database employed. The paper concludes with examples depicting completed and planned trade studies for both normal and superconducting accelerator applications. 8 figs.

Proceedings of the Conference on the Design of Experiments in Army Research Development and Testing (39th) Held in Houston, Texas on 20-22 October 1993

Science.gov (United States)

1994-06-01

exam struc- ture (similar to that of the Society of Actuaries ) which is not a single exam but a series of exams? In this way one can encourage and...April, 1994 from the Technical Management Division, LOSAT Project Office, U.S. Army Missile Command, Attn: SFAX- ASM -LS, Redstone Arsenal, Huntsville...High Reynolds Numbers," Trans, ASME Journal of Fluids Eng., Vol. 105, 1983, pp. 168-173. Kuo, K.K., and Nydegger, C.C., "Flow Resistance Measurements and

Survey Research in the Forest Science Journals - Insights from Journal Editors

Directory of Open Access Journals (Sweden)

Mirjana Stevanov

2015-06-01

Full Text Available Background and Purpose: Survey research is one of the most commonly applied approaches in the social sciences. In the forest research it has been used for more than five decades. In spite of that or the fact that the amount of survey-based articles in the forest science journals has increased during the last decade, their share in all articles published in 20 forest science journals (9,372 articles, 2005-2014 is quite modest (3.2%. In our paper we look at the opinions and attitudes of forest science journal editors towards survey research, as their perspective might enlarge our understanding of the use of this approach in the field of forestry. Materials and Methods: We selected 20 forest science journals - 15 from the SCI list and five non-SCI journals and contacted editors of these journals with the self-administered e-mail questionnaire. Data were collected in October 2014 and analyzed by descriptive statistics. The overall response rate was 75%. The assumptions for the study were based on the evidence addressing opinions and attitudes of journal editors from other research fields (finance since no similar study was found in the field of forestry. Results: The majority of editors reported the same review process for survey-based articles as for all others. In two journals, articles with the survey-based content are screened more rigorously and in two journals their publishing is generally discouraged. 40% of journal editors hold the view that no difference should be made between survey research and other types of original research, and another 40% think that survey research should in the first place play a complementary role. As the main strength of survey research editors see the possibility to obtain data unavailable from other sources. They perceive adverse selection and the difficulty to generalize results as the main weaknesses. Conclusions: Editors of forest science journals have similar opinion on survey research as those from the

Rethinking Constructive Journalism by Means of Service Journalism

DEFF Research Database (Denmark)

From, Unni; Kristensen, Nete Nørgaard

2018-01-01

This article argues that constructive journalism scholarship should look to service journalism and its subfields, cultural journalism and lifestyle journalism, to understand key characteristics of this newer type of journalism. Though constructive journalism is typically associated...... with the reporting of political and social issues, it is also seen to challenge traditional ways of writing about such hard news topics due to its positive and solution-oriented approach. In this respect, constructive journalism seems to reuse some of the approaches known from service journalism, especially in terms...... of audience address and an expanded social role for journalists. However, service journalism emerged in the increasingly commercialized and globalized media landscape of the post-WW2-period, whereas constructive journalism has emerged in the digital media landscape of the 2010s. These historical contexts...

Journal of Biosciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Biosciences. R S Sharma. Articles written in Journal of Biosciences. Volume 26 Issue 4 November 2001 pp 391-405. Current status of fertility control methods in India · R S Sharma M Rajalakshmi D Antony Jeyaraj · More Details Abstract Fulltext PDF. Approximately 48.2% of couples of 15 to 49 ...

Journalism Forum

Science.gov (United States)

Journalism Educator, 1985

1985-01-01

Includes (1) survey results indicating value of traditional journalism and mass communication research; (2) survey results indicating knowledge of grammar, economics, and government are journalists' most valuable resources; (3) methods for teaching listening skills; (4) suggestions for giving public relations students an overview online services;…

Factors associated with the Journal Impact Factor (JIF for Urology and Nephrology Journals

Directory of Open Access Journals (Sweden)

Joseph M. Sewell

2015-12-01

Full Text Available Purpose: The Journal Impact Factor (JIF is an index used to compare a journal's quality among academic journals and it is commonly used as a proxy for journal quality. We sought to examine the JIF in order to elucidate the main predictors of the index while generating awareness among scientific community regarding need to modify the index calculation in the attempt to turn it more accurate. Materials and Methods: Under the Urology and Nephrology category in the Journal Citations Report Website, the top 17 Journals by JIF in 2011 were chosen for the study. All manuscripts’ abstracts published from 2009-2010 were reviewed; each article was categorized based on its research design (Retrospective, Review, etc. T and correlation tests were performed for categorical and continuous variables respectively. The JIF was the dependent variable. All variables were then included in a multivariate model. Results: 23,012 articles from seventeen journals were evaluated with a median of 1,048 (range=78-6,342 articles per journal. Journals with a society affiliation were associated with a higher JIF (p=0.05. Self-citations (rho=0.57, p=0.02, citations for citable articles (rho=0.73, p=0.001, citations to non-citable articles (rho=0.65, p=0.0046, and retrospective studies (rho=-0.51, p=0.03 showed a strong correlation. Slight modifications to include the non-citable articles in the denominator yield drastic changes in the JIF and the ranking of the journals. Conclusion: The JIF appears to be closely associated with the number of citable articles published. A change in the formula for calculating JIF to include all types of published articles in the denominator would result in a more accurate representation.

On the Peripheries of Scholarly Infrastructure: A look at the Journals Using Open Journal Systems

Energy Technology Data Exchange (ETDEWEB)

Alperin, J.P.; Stranack, K.; Garnett, A.

2016-07-01

Although there have been calls for scholarly infrastructure to be inclusive, new layers of infrastructure are built without a clear understanding of the breadth of scholarly journals that lie on the peripheries of the existing infrastructure. In the hopes that future infrastructure can take a wider range of journals into account, this paper presents the results of an effort to track the number, location, and rate of publication of journals using Open Journal Systems, an open source manuscript management and publication system built by the Public Knowledge Project. The method employed, which involves a combination of scanning weblogs, scraping webpages, and harvesting metadata, has yielded an estimated 9,828 journals that have collectively published 2,565,300 articles since 1990. These journals are distributed across 136 countries on 6 continents, and, in 2015, around a fifth of the OJS journals were published in low or low-middle income countries, and over a third in upper-middle income countries, suggesting that the majority of OJS journals are on the on the “periphery” of today's global scholarly infrastructure. As infrastructure and services continue to be developed, this paper argues, it is necessary to look to such journal so that the infrastructure that is built can be developed in a way that is truly inclusive of the global nature of scholarship. (Author)

[E-learning with journal articles].

Science.gov (United States)

Adriaanse, Marcel T; van Eijsden, Pieter; de Leeuw, Peter W

2014-01-01

E-learning is a popular method of continuous medical education (CME) which is becoming increasingly available to doctors. A specific form of E-learning is an online knowledge test accompanying a journal article. CME accreditation points can be obtained by reading an article and then answering test questions on it. This is a user-friendly form of CME which an increasing number of journals are offering as a service to their readers. The Dutch Journal of Medicine (NTvG) has been offering accredited tests to its readers since 2011. On comparison with international journals, a high standard has been set by the development of a test concept in which interpretation and reflection play integral roles. In the Dutch setting, the concept of the test was developed by professional bodies working closely together and it is a concept that is used as an example to other journals.

The Flipped Journal Club

Directory of Open Access Journals (Sweden)

Richard Bounds

2017-12-01

Full Text Available Introduction Educators struggle to develop a journal club format that promotes active participation from all levels of trainees. The explosion of social media compels residencies to incorporate the evaluation and application of these resources into evidence-based practice. We sought to design an innovative “flipped journal club” to achieve greater effectiveness in meeting goals and objectives among residents and faculty. Methods Each journal club is focused on a specific clinical question based on a landmark article, a background article, and a podcast or blog post. With the “flipped” model, residents are assigned to prepare an in-depth discussion of one of these works based on their level of training. At journal club, trainees break into small groups and discuss their assigned readings with faculty facilitation. Following the small-group discussions, all participants convene to summarize key points. In redesigning our journal club, we sought to achieve specific educational outcomes, and improve participant engagement and overall impressions. Results Sixty-one residents at our emergency medicine program participated in the flipped journal club during the 2015–2016 academic year, with supervision by core faculty. Program evaluation for the flipped journal club was performed using an anonymous survey, with response rates of 70% and 56% for residents and faculty, respectively. Overall, 95% of resident respondents and 100% of faculty respondents preferred the flipped format. Conclusion The “flipped journal club” hinges upon well-selected articles, incorporation of social media, and small-group discussions. This format engages all residents, holds learners accountable, and encourages greater participation among residents and faculty.

Desobstrução ineficaz das vias aéreas em crianças asmáticas: um estudo descritivo

Directory of Open Access Journals (Sweden)

Lanuza Celes Mendes

2012-01-01

Full Text Available Estudio transversal realizado con 147 niños asmáticos ingresados en un hospital público de Fortaleza-CE, Brasil. Ha sido desarrollado con el objetivo de analizar la efectividad de las características definitorias del diagnóstico de enfermería "limpieza ineficaz de las vías aéreas" en niños asmáticos. Se utilizó un guión de examen físico para recopilar los datos. Las características definitorias más frecuentes fueron ruidos respiratorios agregados (82,3%, disnea (55,8% y cambio en la frecuencia respiratoria (50,3%. El diagnóstico de enfermería: "limpieza ineficaz de las vías aéreas" estuvo presente en el 55,8% de la muestra. La característica definitoria para este diagnóstico fueron los "ruidos respiratorios agregados". La característica específica ha sido "ojos muy abiertos". Con relación a los valores predictivos, los ruidos respiratorios agregados presentaron un alto valor predictivo negativo. Se llegó a la conclusión de que los estudios que contribuyen a configurar el perfil de las características definitorias más comunes a una población particular deben ser fomentados, pues sirven de guía para la práctica de enfermería.

South African Journal of Bioethics and Law: Journal Sponsorship

African Journals Online (AJOL)

South African Journal of Bioethics and Law: Journal Sponsorship. Journal Home > About the Journal > South African Journal of Bioethics and Law: Journal Sponsorship. Log in or Register to get access to full text downloads.

Journal of Computer Science and Its Application: Journal Sponsorship

African Journals Online (AJOL)

Journal of Computer Science and Its Application: Journal Sponsorship. Journal Home > About the Journal > Journal of Computer Science and Its Application: Journal Sponsorship. Log in or Register to get access to full text downloads.

Nigeria Journal of Pure and Applied Physics: Journal Sponsorship

African Journals Online (AJOL)

Nigeria Journal of Pure and Applied Physics: Journal Sponsorship. Journal Home > About the Journal > Nigeria Journal of Pure and Applied Physics: Journal Sponsorship. Log in or Register to get access to full text downloads.

OGIRISI: a New Journal of African Studies: Journal Sponsorship

African Journals Online (AJOL)

OGIRISI: a New Journal of African Studies: Journal Sponsorship. Journal Home > About the Journal > OGIRISI: a New Journal of African Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

Journal of Research in Forestry, Wildlife and Environment: Journal ...

African Journals Online (AJOL)

Journal of Research in Forestry, Wildlife and Environment: Journal Sponsorship. Journal Home > About the Journal > Journal of Research in Forestry, Wildlife and Environment: Journal Sponsorship. Log in or Register to get access to full text downloads.

Journal of the Nigerian Association of Mathematical Physics: Journal ...

African Journals Online (AJOL)

Journal of the Nigerian Association of Mathematical Physics: Journal Sponsorship. Journal Home > About the Journal > Journal of the Nigerian Association of Mathematical Physics: Journal Sponsorship. Log in or Register to get access to full text downloads.

Use of the Paid Open Access Option in Hybrid Open Access Journals in Agriculture: A Mixed-Methods Study

Directory of Open Access Journals (Sweden)

Megan Kocher

2016-12-01

Full Text Available We explore the use and usefulness of the hybrid open access publishing model in agricultural sciences using a combination of quantitative and qualitative methods. To ascertain the level of usage of the paid open access option in hybrid open access journals in agriculture, we studied the agriculture-related journals published by six commercial publishers. These publishers offer authors the option of paying a fee, often close to $3,000 per article, to make their article immediately freely available, usually with a Creative Commons license. We defined agriculture broadly but also assigned each journal to a subspecialty (e.g., animal science in order to see if there were differences based on these subdivisions. For each journal we gathered data for 2014-2015 and noted the total number of research articles and the number of those that were made freely available by authors paying the open access fee. To give context to our results we also surveyed local faculty in agricultural sciences, asking their reasons for considering the paid open access options and the sources of the funds to pay for it. Survey respondents were asked about their academic position and rank to see if there were differences to be noted. We also investigated the findability of the open access articles, noting if each individual publisher offered a way to easily locate all the freely available articles in a particular journal and if there are other avenues to easily locate these articles.

Update on ASME rules for spent nuclear fuel and high level radioactive material and waste storage containments

International Nuclear Information System (INIS)

Ralph S. Hill III; Foster, G.M.

2005-01-01

In 2004, a new Code Case, N-717, of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (Code) was published. The Code Case provides rules for construction of containments used for storage of spent nuclear fuel and high level radioactive material and waste. The Code Case has been incorporated into Section III of the Code as Division 3, Subsection WC, Class SC Storage Containments, and will be published in the 2005 Addenda. This paper provides an informative background and insight for these rules to provide Owners, regulators, designers, and fabricators with a more comprehensive understanding of the technical basis for these rules. (authors)

A Comparison of the Variability of the Symbiotic X-ray Binaries GX 1+4, 4U 1954+31, and 4U 1700+24 from Swift/BAT and RXTE/ASM Observations

Science.gov (United States)

Corbet, R. H. D.; Sokoloski, J. L.; Mukai, K.; Markwardt, C. B.; Tueller, J.

2007-01-01

We present an analysis of the X-ray variability of three symbiotic X-ray binaries, GX 1+4, 4U 1700+24, and 4U 1954+31, using observations made with the Swift Burst Alert Telescope (BAT) and the Rossi X-ray Timing Explorer (RXTE) All-Sky Monitor (ASM). Observations of 4U 1954+31 with the Swift BAT show modulation at a period near 5 hours. Models to explain this modulation are discussed including the presence of an exceptionally slow X-ray pulsar in the system and accretion instabilities. We conclude that the most likely interpretation is that 4U 1954+31 contains one of the slowest known X-ray pulsars. Unlike 4U 1954+31, neither GX 1+4 nor 4U 1700+24 show any evidence for modulation on a timescale of hours. An analysis of the RXTE ASM light curves of GX l+4, 4U 1700+24, and 4U 1954+31 does not show the presence of periodic modulation in any source, although there is considerable variability on long timescales for all three sources. There is no modulation in GX 1+4 on either the optical 1161 day orbital period or a previously reported 304 day X-ray period. For 4U 1700+24 we do not confirm the 404 day period previously proposed for this source from a shorter duration ASM light curve.

Quality of reporting statistics in two Indian pharmacology journals

OpenAIRE

Jaykaran,; Yadav, Preeti

2011-01-01

Objective: To evaluate the reporting of the statistical methods in articles published in two Indian pharmacology journals. Materials and Methods: All original articles published since 2002 were downloaded from the journals′ (Indian Journal of Pharmacology (IJP) and Indian Journal of Physiology and Pharmacology (IJPP)) website. These articles were evaluated on the basis of appropriateness of descriptive statistics and inferential statistics. Descriptive statistics was evaluated on the basis of...

Analysis of Statistical Methods and Errors in the Articles Published in the Korean Journal of Pain

Science.gov (United States)

Yim, Kyoung Hoon; Han, Kyoung Ah; Park, Soo Young

2010-01-01

Background Statistical analysis is essential in regard to obtaining objective reliability for medical research. However, medical researchers do not have enough statistical knowledge to properly analyze their study data. To help understand and potentially alleviate this problem, we have analyzed the statistical methods and errors of articles published in the Korean Journal of Pain (KJP), with the intention to improve the statistical quality of the journal. Methods All the articles, except case reports and editorials, published from 2004 to 2008 in the KJP were reviewed. The types of applied statistical methods and errors in the articles were evaluated. Results One hundred and thirty-nine original articles were reviewed. Inferential statistics and descriptive statistics were used in 119 papers and 20 papers, respectively. Only 20.9% of the papers were free from statistical errors. The most commonly adopted statistical method was the t-test (21.0%) followed by the chi-square test (15.9%). Errors of omission were encountered 101 times in 70 papers. Among the errors of omission, "no statistics used even though statistical methods were required" was the most common (40.6%). The errors of commission were encountered 165 times in 86 papers, among which "parametric inference for nonparametric data" was the most common (33.9%). Conclusions We found various types of statistical errors in the articles published in the KJP. This suggests that meticulous attention should be given not only in the applying statistical procedures but also in the reviewing process to improve the value of the article. PMID:20552071

Calidad de vida en el adolescente asmático Quality of life in the asthmatic adolescent

Directory of Open Access Journals (Sweden)

Orquídea Aguirre Pérez

2010-12-01

Full Text Available INTRODUCCIÓN: la mejoría de la calidad de vida es clave en el tratamiento del niño-adolescente con asma. OBJETIVO: identificar la afectación que provoca el asma bronquial en la calidad de vida del adolescente asmático. MÉTODOS: se realizó un estudio descriptivo, longitudinal y prospectivo de 103 adolescentes asmáticos con diagnóstico de asma leve intermitente, asma leve persistente y asma moderada persistente en la Escuela Secundaria Básica "Antonio José de Sucre", en la localidad de Cojímar, en el período entre el 1ro. de enero de 2006 y el 31 de diciembre del propio año. RESULTADOS: los síntomas principales fueron la tos, la disnea y la sibilancia, y las molestias más frecuentes, el cansancio, la dificultad para respirar hondo y la sensación de quedar sin aire. Predominó el sexo masculino y las edades de 12 y 13 años. El mayor número de respuestas de las alteraciones de la función emocional se concentraba en las categorías más bajas del nivel de afectación, y las respuestas sobre la limitación de la actividad motora se inclinaron hacia las categorías de muchísimo, mucho, bastante y regular. Predominó la afectación moderada de la calidad de vida. El asma persistente moderada fue la mayormente referida en la afectación de calidad de vida severa.INTRODUCTION: the improvement in quality of life is a key element in treatment of asthmatic child-adolescent. OBJECTIVE: to identify the affection provoking the bronchial asthma in the quality of life of the asthmatic adolescent. METHODS: a prospective longitudinal and descriptive study was conducted in 103 asthmatic adolescents diagnosed with intermittent slight asthma from the "Antonio José de Sucre" Secondary Basic School in the Cojimar place, from January 1, to December 31, 2006. RESULTS: the major symptoms included cough, dyspnea and sibilation and the more frequent nuisances were the tiredness, profound breathlessness and the feeling of lack of air. There was

Good journalism or peace journalism?

Directory of Open Access Journals (Sweden)

David Loyn

2007-10-01

Full Text Available This paper argues against the prescriptive notions of Peace Journalism, and in particular its exclusive nature and attempt to define itself as a new orthodoxy. Most of the paper is a critique of the work of Jake Lynch and Annabel McGoldrick, in a book published in 2005, as well as their earlier Reporting the World series. They condemn all other ways of reporting as 'War Journalism, biased in favour of war.' I argue instead that the opposite of Peace Journalism is good journalism. Much of this Peace Journalism argument is derived from the work of Johan Galtung, who accuses 'war journalists' of reporting war in an enclosed space and time, with no context, concealing peace initiatives and making wars 'opaque/secret.' Galtung specifically calls on journalists as part of their mission to search out peace proposals which might begin as something small and beneath notice, but which might then be picked up and owned by politicians as their own. My response is clear and simple: creating peacemaking politicians is not the business of a reporter. I examine the traditional journalistic methods of using objectivity to get at a version of the truth. I concede that perfect truth is unattainable, (and paradoxically the tool of objectivity we use to get there is slippery too. I conclude that a more quotidian truth, or 'truthfulness' is though a manageable goal. I engage with philosophers who examine objectivity, concluding with the assistance of Thomas Nagel that it does still have a value. Nagel's account also has the merit of explaining how practices such as peace-reporting are bound to be less objective than alternatives, 'since they commit themselves to the adoption of particular perspectives, in effect giving up on the ideal of stripping away as much…as possible.' I examine the responses of the so-called 'journalism of attachment' framed as a desire of journalists faced by the horrors of Bosnia to cast off impartiality and emotional detachment and take

Journal of Biosciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

2007-06-28

Jun 28, 2007 ... Home; Journals; Journal of Biosciences; Volume 32; Issue 5 ... These methods suffer from disadvantages such as the lack of availability of ... In this work, we have constructed a library of local conformation classes purely ...

Fatores de risco para hospitalização de crianças e adolescentes asmáticos

Directory of Open Access Journals (Sweden)

Laura Lasmar

2002-08-01

Full Text Available OBJETIVO: Verificar a ocorrência e os fatores de risco associados à hospitalização de um grupo de crianças asmáticas e realizar diagnóstico da assistência à saúde desses pacientes. MÉTODOS: Foram estudados 325 pacientes (crianças e adolescentes asmáticos, registrados em um ambulatório de referência, sendo que 202 já haviam sido hospitalizados. O diagnóstico da assistência prestada foi feito por meio de formulário que abordou características gerais das hospitalizações e fatores biológicos, demográficos, socioeconômicos e os relacionados à asma. Análises univariada e multivariada foram empregadas para verificar a associação entre variáveis independentes e a ocorrência de hospitalização. RESULTADOS: Dos pacientes estudados, 62,2% já haviam sido hospitalizados durante sua moléstia, 64,9% iniciaram crises, e 60,9% se internaram no primeiro ano de vida. A maioria (76,0% apresentava formas clínicas moderadas e graves. Apesar disto, 94,2% não estavam em uso de drogas profiláticas, recebendo assistência apenas durante o episódio agudo. Nenhum dos pacientes se encontrava vinculado à atenção primária para controle periódico da doença e profilaxia com corticosteróides inalados. Os familiares (97,8% não dispunham de conhecimentos básicos necessários ao manejo da asma. Os principais fatores de risco para hospitalização foram: a idade de início dos sintomas antes de 12 meses de idade (OR=3,20, IC95%, 1,55-6,61 ou entre 12 e 24 meses (OR=3,89, IC95%, 1,62-9,36, a escolaridade materna inferior a sete anos de estudos (OR=3,06, IC95%, 1,62-5,76, a gravidade da doença (OR=2,32, IC95%, 1,36-3,96, o número de consultas a serviços de urgência igual ou superior a duas vezes por mês (OR=2,19, IC95%, 1,24-3,88 e o diagnóstico de encaminhamento de pneumonia de repetição (OR=2,00; IC95%, 1,06-3,80. CONCLUSÃO: Com vistas à redução dos índices de hospitalização, os serviços de saúde devem se organizar para

Fatores de risco para hospitalização de crianças e adolescentes asmáticos

Directory of Open Access Journals (Sweden)

Lasmar Laura

2002-01-01

Full Text Available OBJETIVO: Verificar a ocorrência e os fatores de risco associados à hospitalização de um grupo de crianças asmáticas e realizar diagnóstico da assistência à saúde desses pacientes. MÉTODOS: Foram estudados 325 pacientes (crianças e adolescentes asmáticos, registrados em um ambulatório de referência, sendo que 202 já haviam sido hospitalizados. O diagnóstico da assistência prestada foi feito por meio de formulário que abordou características gerais das hospitalizações e fatores biológicos, demográficos, socioeconômicos e os relacionados à asma. Análises univariada e multivariada foram empregadas para verificar a associação entre variáveis independentes e a ocorrência de hospitalização. RESULTADOS: Dos pacientes estudados, 62,2% já haviam sido hospitalizados durante sua moléstia, 64,9% iniciaram crises, e 60,9% se internaram no primeiro ano de vida. A maioria (76,0% apresentava formas clínicas moderadas e graves. Apesar disto, 94,2% não estavam em uso de drogas profiláticas, recebendo assistência apenas durante o episódio agudo. Nenhum dos pacientes se encontrava vinculado à atenção primária para controle periódico da doença e profilaxia com corticosteróides inalados. Os familiares (97,8% não dispunham de conhecimentos básicos necessários ao manejo da asma. Os principais fatores de risco para hospitalização foram: a idade de início dos sintomas antes de 12 meses de idade (OR=3,20, IC95%, 1,55-6,61 ou entre 12 e 24 meses (OR=3,89, IC95%, 1,62-9,36, a escolaridade materna inferior a sete anos de estudos (OR=3,06, IC95%, 1,62-5,76, a gravidade da doença (OR=2,32, IC95%, 1,36-3,96, o número de consultas a serviços de urgência igual ou superior a duas vezes por mês (OR=2,19, IC95%, 1,24-3,88 e o diagnóstico de encaminhamento de pneumonia de repetição (OR=2,00; IC95%, 1,06-3,80. CONCLUSÃO: Com vistas à redução dos índices de hospitalização, os serviços de saúde devem se organizar para

A study on literature obsolescence and core journals' cost-benefit in citations of the 'Scientific Medical Journal of Ahwaz'.

Science.gov (United States)

Zare-Farashbandi, Firoozeh; Mohammadi, Parastoo Parsaei

2014-01-01

One of the methods of identifying core and popular resources is by citation evaluation. Using citation evaluation, the librarians of the Acquisition Department can use quantitative methods to indentify core and popular resources among numerous information resources and make serious savings in the library's budget, by acquiring these core resources and eliminating useless ones. The aim of this study is assessing literature obsolescence and core journals' cost-benefit in citations of the 'Scientific Medical Journal of Ahwaz'. This study is a descriptive and cross-sectional survey that uses citation analysis. Sampling is objective sampling from all documents from years 1364 (1985) to 1385 (2006), and the population comprises of 6342 citations of the articles published in 'Scientific Medical Journal of Ahwaz'. Data collection is done through referring to the original documents and the data is analyzed using the Excel software, and for descriptive and analytical statistics the cost-benefit formula and Bradford law formula are used. Findings showed that the average citation for each document in the 'Scientific Medical Journal of Ahwaz' was 15.81. The average citation to international sources was 14.37, and the average citation to national sources was 1.44. The literature obsolescence of Farsi documents in this study was 15 years, while it was equal to 20 years for English documents. The highly cited Farsi journals were (sorted based on citation in descending order): 'Scientific Medical Journal of Ahwaz', 'Daroudarman', 'Nabz,' and 'Journal of Medical School, Shahid Beheshti University of Medical Sciences'. The highly cited English journals were (sorted based on citation in descending order): 'Pediatrics', 'The New England Journal of Medicine', 'Gastroenterology' and 'Medicine'. All of these four journals are part of the ISI database and have good impact factors in the Journal Citation Reports (JCR). Also their cost-benefit was reasonable based on the frequency of their

Improved Monte Carlo Method for PSA Uncertainty Analysis

International Nuclear Information System (INIS)

Choi, Jongsoo

2016-01-01

The treatment of uncertainty is an important issue for regulatory decisions. Uncertainties exist from knowledge limitations. A probabilistic approach has exposed some of these limitations and provided a framework to assess their significance and assist in developing a strategy to accommodate them in the regulatory process. The uncertainty analysis (UA) is usually based on the Monte Carlo method. This paper proposes a Monte Carlo UA approach to calculate the mean risk metrics accounting for the SOKC between basic events (including CCFs) using efficient random number generators and to meet Capability Category III of the ASME/ANS PRA standard. Audit calculation is needed in PSA regulatory reviews of uncertainty analysis results submitted for licensing. The proposed Monte Carlo UA approach provides a high degree of confidence in PSA reviews. All PSA needs accounting for the SOKC between event probabilities to meet the ASME/ANS PRA standard

Improved Monte Carlo Method for PSA Uncertainty Analysis

Energy Technology Data Exchange (ETDEWEB)

Choi, Jongsoo [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2016-10-15

The treatment of uncertainty is an important issue for regulatory decisions. Uncertainties exist from knowledge limitations. A probabilistic approach has exposed some of these limitations and provided a framework to assess their significance and assist in developing a strategy to accommodate them in the regulatory process. The uncertainty analysis (UA) is usually based on the Monte Carlo method. This paper proposes a Monte Carlo UA approach to calculate the mean risk metrics accounting for the SOKC between basic events (including CCFs) using efficient random number generators and to meet Capability Category III of the ASME/ANS PRA standard. Audit calculation is needed in PSA regulatory reviews of uncertainty analysis results submitted for licensing. The proposed Monte Carlo UA approach provides a high degree of confidence in PSA reviews. All PSA needs accounting for the SOKC between event probabilities to meet the ASME/ANS PRA standard.

Timelag between submission and publication of an article to scientific journal. Special feature: Scientific journal, today

International Nuclear Information System (INIS)

Ishikawa, Masashi

1994-01-01

As to the period till the papers that researchers contributed to journals are published and the period till the papers published in journals are contained in data bases, investigation was carried out on three main journals in atomic energy field. Moreover, also as to the issue of preprints which have been circulated in the field of physics, investigation was carried out. As the results of investigation, the period till being published in journlas was from 6 months to 16 months, and the period till being contained in data bases was from 4 months to 9 months. Since preprints are issued by several months earlier than journals, those have large merit for the quick publication of the results of researches. There are about 10,000 scientific journals that publish the papers in atomic energy field in the world. Journals are the place where researchers publish the results of researches and the important information source for knowing the recent trend of research. The procedure of publishing contributed papers in journals is explained. The method of investigating the time lag and the results are reported. The examination of papers by editorial committee takes time. (K.I.)

Journal of Biosciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

2009-12-09

Dec 9, 2009 ... Home; Journals; Journal of Biosciences; Volume 34; Issue 6 ... and suitable teaching methods have been of great importance in the progress of knowledge. ... And what is valid for the learning of anatomy can be generalized to ...

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences. G Ranga Rao. Articles written in Journal of Chemical Sciences. Volume 113 Issue 5-6 October-December 2001 pp 651-658. XRD and UV-Vis diffuse reflectance analysis of CeO2-ZrO2 solid solutions synthesized by combustion method · G Ranga Rao H Ranjan Sahu.

Resonance – Journal of Science Education | Indian Academy of ...

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education. Raamesh Gowri Raghavan. Articles written in Resonance – Journal of Science Education. Volume 10 Issue 1 January 2005 pp 17-24 General Article. Numerical Methods in Linguistics - An Introduction to Glottochronology · Raamesh Gowri Raghavan.

Citation analysis of five journals in andrology.

Science.gov (United States)

Yang, H; Pan, B-C; Chen, J

2006-01-01

To find out features in literature demand by researchers in the field of andrology and to offer advice on literature utilization and journal management. Five andrology journals indexed by Science Citation Index Expanded (SCI-E) (Andrologia, Archives of Andrology, Asian Journal of Andrology, International Journal of Andrology, and Journal of Andrology) were included in the study. Original articles, editorials, reviews, corrections and letters from these journals were analyzed with bibliometric method for document loading, citations, information absorbing ability, and geographical coverage. The average number of references in each paper was 28.78. The main type of references was periodicals (94.32%), while books and other sources accounted for only 5.68%. Average Price index was 30.14%. The number of references in the first ranking 10 periodicals cited by the five journals made up 34.53% of the total references cited. Geographically, the five journals covered 6 continents with 42 countries or regions. Andrology journals have a wide coverage of literatures, which are related to reproductive medicine, urology, endocrinology and biochemistry. References in andrology journals are mainly periodicals and are relatively old. US, China and Japan lead the world in andrology researches for the number of papers published.

Journals Abroad

Science.gov (United States)

Ando, Shoichi

1975-01-01

This article summarizes four journal articles on language teaching appearing in the American pedagogical language journals, "The Modern Language Journal,""English Language Teaching Journal," and "TESOL Quarterly." The purpose is to give an indication of what kinds of articles can be found in journals outside Japan.…

Journal Management

African Journals Online (AJOL)

The Journal Manager sees to all aspects of Journal Management, in consultation with the Editors, including setting up and configuring the journal system, enrolling users in the various roles needed to run the journal, setting up the various Sections of the journal, and many other managerial tasks.

A literature survey on numerical heat transfer

Science.gov (United States)

Shih, T. M.

1982-12-01

Technical papers in the area of numerical heat transfer published from 1977 through 1981 are reviewed. The journals surveyed include: (1) ASME Journal of Heat Transfer, (2) International Journal of Heat and Mass Transfer, (3) AIAA Journal, (4) Numerical Heat Transfer, (5) Computers and Fluids, (6) International Journal for Numerical Methods in Engineering, (7) SIAM Journal of Numerical Analysis, and (8) Journal of Computational Physics. This survey excludes experimental work in heat transfer and numerical schemes that are not applied to equations governing heat transfer phenomena. The research work is categorized into the following areas: (A) conduction, (B) boundary-layer flows, (C) momentum and heat transfer in cavities, (D) turbulent flows, (E) convection around cylinders and spheres or within annuli, (F) numerical convective instability, (G) radiation, (H) combustion, (I) plumes, jets, and wakes, (J) heat transfer in porous media, (K) boiling, condensation, and two-phase flows, (L) developing and fully developed channel flows, (M) combined heat and mass transfer, (N) applications, (O) comparison and properties of numerical schemes, and (P) body-fitted coordinates and nonuniform grids.

American Society of Maxillofacial Surgeons 2006 to 2016: Another Decade of Excellence in Education and Research.

Science.gov (United States)

Doumit, Gaby; Totonchi, Ali; Wexler, Andy; Gosain, Arun K

2017-09-01

Over the past 10 years, the American Society of Maxillofacial Surgeons (ASMS) has continued to advance to meet its mission of being the premier organization to represent maxillofacial and pediatric plastic surgery in the United States. These advances are focused on education of its members, to include the American Society of Maxillofacial Surgeons basic course, the preconference symposium, the annual meeting, two basic maxillofacial courses per year, advanced maxillofacial courses, a boot camp for craniofacial fellows, a cleft course, quarterly webinars, sponsored fellowships, a visiting professorship, and the ASMS journal. In addition, the ASMS has continued to advance as the premier national organization representing maxillofacial and pediatric plastic surgery in the United States, thereby positioning the organization as a primary advocate for these surgical specialties. Outreach of the ASMS has grown over the past decade and now includes representatives to the American Society of Plastic Surgeons/Plastic Surgery Foundation, the American Board of Plastic Surgeons, the American Medical Association, and most recently a seat as a governor with the American College of Surgeons. The ASMS has also initiated an annual Summer Leadership Seminar to explore topics of relevance in a changing health care environment. The present report outlines the major initiatives of the ASMS over the past 10 years.

MARKET CONCENTRATION IN TURKISH JOURNALISM SECTOR

Directory of Open Access Journals (Sweden)

ADEM KALÇA

2013-05-01

Full Text Available Concentration is a situation in which market structure of a sector is controlled by a few firms. At the present time, many analyzing methods such as Herfindahl-Hirschman and N-Firm Concentration Indexes are used to determine market structure.According to market concentration indexes, higher concentration level means more monopolistic market structure, lower concentration level means more full competitive market structure. In this study concentration levels of media groups in Turkish journalism sector within the scope of traditional journalism and internet journalism was analyzed via N-Firm Concentration and H-H Indexes. As a result of the study, it’s seen that first four biggest media groups have monopolistic competition in internet journalism sector,and oligopol structure in traditional journalism sector. According to H-H index analyze, there is monopolistic competition in the sector.

Definition and identification of journals as bibliographic and subject entities: Librarianship versus ISI Journal Citation Reports methods and their effect on citation measures

NARCIS (Netherlands)

Bensman, S.J.; Leydesdorff, L.

2009-01-01

This paper explores the ISI Journal Citation Reports (JCR) bibliographic and subject structures through Library of Congress (LC) and American research libraries cataloging and classification methodology. The 2006 Science Citation Index JCR Behavioral Sciences subject category journals are used as an

Journal of the Cameroon Academy of Sciences: About this journal

African Journals Online (AJOL)

Journal of the Cameroon Academy of Sciences: About this journal. Journal Home > Journal of the Cameroon Academy of Sciences: About this journal. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Journal Home · ABOUT THIS JOURNAL · Advanced Search ...

Risk-informed appendices G and E for section XI of the ASME Boiler and Pressure Vessel Code

International Nuclear Information System (INIS)

Carter, B; Spanner, J.; Server, W.; Gamble, R.; Bishop, B.; Palm, N.; Heinecke, C.

2011-01-01

Full text of publication follows: The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section XI, contains two appendices (G and E) related to reactor pressure boundary integrity. Appendix G provides procedures for defining Service Level A and B pressure temperature limits for ferritic components in the reactor coolant pressure boundary. Recently, an alternative risk informed methodology has been developed for ASME Section XI, Appendix G. The alternative methodology provides simple procedures to define risk informed pressure temperature limits for Service Level A and B events, including leak testing and reactor start up and shut down for both pressurized water reactors (PWRs) and boiling water reactors (BWRs). Risk informed pressure temperature limits provide more operational flexibility, particularly for reactor pressure vessels (RPV) with relatively high irradiation levels and radiation sensitive materials. Appendix E of Section XI provides a methodology for assessing conditions when the Appendix G limits are exceeded. A similar risk informed methodology is being considered for Appendix E. The probabilistic fracture mechanics evaluations used to develop the risk informed relationships included appropriate material properties for the range of RPV materials in operating plants in the United States and operating history and system operational constraints in both BWRs and PWRs. The analysis results were used to define pressure temperature relationships that provide an acceptable level of risk, consistent with safety goals defined by the U.S. Nuclear Regulatory Commission. The alternative methodologies for Appendices G and E will provide greater operational flexibility, especially for Service Level A and B events that may adversely affect efficient and safe plant operation, such as low temperature over pressurization for PWRs and BWR leak testing. Overall, application of the risk informed appendices can result in increased plant

Rehabilitación integral y tolerancia al ejercicio físico en escolares asmáticos severos

Directory of Open Access Journals (Sweden)

. Héctor Alejandro Cruz Oliver

1995-04-01

Full Text Available Se realizó un estudio en 99 escolares asmáticos severos, incluidos en un programa de rehabilitación integral en el centro para niños asmáticos de la Ciudad de los Pioneros "José Martí" en Tarará, durante el curso escolar 1991-1992. A todos los escolares se les sometió antes de comenzar el programa, a una prueba de tolerancia al ejercicio físico mediante la carrera libre, y acorde con los resultados de ésta se clasificaron en 2 grupos; grupo I, con asma inducida por el ejercicio (AIE y grupo II, sin AIE. Al finalizar el programa de rehabilitación al grupo I se le sometió nuevamente a la prueba de tolerancia al ejercicio físico. Todos los escolares se evaluaron mediante la espirometría en condiciones basales antes del programa de rehabilitación y al finalizar éste. En 55 escolares (55,5 % se constató la presencia inicial de AIE. Al finalizar el programa de rehabilitación sólo en 23 de ellos se mantuvo este fenómeno. Con excepción de un escolar perteneciente al grupo I el resto de los niños toleraron sin dificultad las actividades físicas programadas. En relación con los parámetros de función respiratoria no se hallaron diferencias significativas en ninguno de ellos, cuando se compararon ambos grupos entre sí antes del programa de rehabilitación, y después de él. Comparando cada grupo consigo mismo sólo se observó un incremento significativo del flujo máximo medio (MMF en ambos grupos, lo que reflejó una disminución del componente obstructivo bronquial periférico.

Reporting research methods of empirical studies | Korb | Journal of ...

African Journals Online (AJOL)

Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL · News. OTHER RESOURCES.

Creative Artist: A Journal of Theatre and Media Studies: Journal ...

African Journals Online (AJOL)

Creative Artist: A Journal of Theatre and Media Studies: Journal Sponsorship. Journal Home > About the Journal > Creative Artist: A Journal of Theatre and Media Studies: Journal Sponsorship. Log in or Register to get access to full text downloads.

Relação da medida da amplitude tóraco-abdominal de adolescentes asmáticos e saudáveis com seu desempenho físico

Directory of Open Access Journals (Sweden)

Renata Pedrolongo Basso

Full Text Available OBJETIVOS: Este estudo teve como objetivo verificar as diferenças das amplitudes tóraco-abdominais nos três níveis (axilar, xifoide e abdominal, nos adolescentes asmáticos e nos saudáveis, e compará-las entre eles. Além de relacioná-las com a capacidade de exercício físico. MATERIAIS E MÉTODOS: Foram avaliados 38 adolescentes, na faixa etária dos 11 aos 15 anos, de ambos os sexos, sendo 19 adolescentes asmáticos, que compuseram o grupo asmático (GA, e 19 saudáveis, que compuseram o grupo saudável (GS. Foi preenchida uma ficha de anamnese e realizada a avaliação antropométrica, espirométrica, o teste do degrau de seis minutos (TD6 e a cirtometria, e calculado o índice de amplitude tóraco-abdominal (IA RESULTADOS: Observou-se diferença significativa para IA entre os níveis axilar e abdominal e xifoidiano e abdominal em ambos os grupos. Não houve diferença significativa quanto ao IA entre os grupos. Somente no GA houve correlação positiva do número total de subidas no TD6 com o IA axilar e xifoide. CONCLUSÃO: Para adolescentes com asma intermitente e persistente leve não houve diferença na cirtometria tóraco-abdominal quando comparados aos saudáveis e houve correlação dos IA axilar e xifoidiano com o desempenho físico no TD6.

Journal of Earth System Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Earth System Science. V S Dubey. Articles written in Journal of Earth System Science. Volume 114 Issue 5 October 2005 pp 515-522. Identification of groundwater prospective zones by using remote sensing and geoelectrical methods in Jharia and Raniganj coalfields, Dhanbad district, ...

Journal of Earth System Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Journal of Earth System Science. G Sasibhushana Rao. Articles written in Journal of Earth System Science. Volume 116 Issue 5 October 2007 pp 407-411. GPS satellite and receiver instrumental biases estimation using least squares method for accurate ionosphere modelling · G Sasibhushana Rao.

Resonance – Journal of Science Education | Indian Academy of ...

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education. Mugdha Deshpande. Articles written in Resonance – Journal of Science Education. Volume 5 Issue 11 November 2000 pp 56-68 General Article. Techniques of WasteWater Treatment - Introduction to Effluent Treatment and Industrial Methods · Amol A Kulkarni ...

Journal Home

African Journals Online (AJOL)

for Researchers · for Journals · for Authors · for Policy Makers · about Open Access · Journal Quality. 521 African Journals. Browse By Category · Browse Alphabetically · Browse By Country · List All Titles · Free To Read Titles This Journal is Open Access. Featuring journals from 32 Countries: Algeria (5); Benin (2); Botswana ...

Investigation of the Stress Intensity Limits of ASME Section III Div.5 for Structure Design Criteria of SFR Fuel Assembly

Energy Technology Data Exchange (ETDEWEB)

Choo, Jin-Yup; Kim, Hyung-Kyu; Cheon, Jin-Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

These affect the mechanical design of the fuel assembly components. And thus, appropriate structural design criteria should also be chosen to incorporate the specific design conditions of the SFR fuel assemblies. Among them, the temperature is one of the most crucial conditions to be concerned because the sodium coolant temperature is normally more than 500ºC which is much higher than that of the LWR (< 350ºC). This implies that a thermal creep should be significantly considered in the SFR fuel assembly mechanical design. In addition to the high temperature condition, an irradiation swelling is also an important behavior that the SFR fuel assembly material should accommodate. To incorporate the temperature and irradiation impacts, the material of the fuel assembly components is presently determined to be made of HT-9, the ferriticmartensitic steel. In this paper, the ASME Sec. III Div. 5 (referred to as ‘Div. 5’ hereinafter), which was developed for a ‘high temperature reactor’, is considered as one of the structural design criteria for the mechanical design of SFR fuel assemblies. In this paper, the stress intensity limits, S{sub m} and S{sub t} of HT-9 were built for the structural criteria of an SFR fuel assembly. S{sub m} is obtained from the ultimate strength. As for S{sub t}, it is more complicated because of its dependency of time duration in addition to temperature. Following the definition of S{sub mt}, the method in the ASME Sec. III Div. 1, Subsec. NH was consulted. We found that the Sm is adopted as S{sub mt} under the temperature about 470ºC which is relatively low temperature range and over 470ºC with relatively short time duration as 1000 hours. And the S{sub t} is adopted as Smt at over 470ºC and long time duration over 34800 hours, and over 520ºC and 10{sup 4} hours too. And at over 570ºC and 1000 hours, and at over 630ºC and 100 hours, S{sub t} is also adopted for S{sub mt}.

[Scientific stealing (Plagiarism) in medical journals].

Science.gov (United States)

Enöz, Murat

2007-01-01

The obligation to publish academic papers in order to get academic rank has made medical doctors more ambitious to publish faster and more papers. According to the ethical and legal rules in our country and in the world, if an idea or technical methods of another person is used in a medical journal, the owner of the method or idea and its publication has to be cited. If an idea, information or a technical method of another scientist is published without citation as if it was one's own idea it's called "Plagiarism". Despite the prohibitive laws and rules, this scientific stealing has become an increasing problem for medical journals worldwide.

Pramana – Journal of Physics | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics. Barnali Chakrabarti. Articles written in Pramana – Journal of Physics. Volume 65 Issue 1 July 2005 pp 61-74 Research Articles. Application of potential harmonic expansion method to BEC: Thermodynamic properties of trappedNa atoms · Anasuya Kundu Barnali Chakrabarti ...

The new equation of steam quality and the evaluation of nonradioactive tracer method in PWR steam generators

International Nuclear Information System (INIS)

Ki Bang, Sung; Young Jin, Chang

2001-01-01

The performance of steam turbines is tested as ANSI/ASME-PTC 6. This code provides rules for the accurate testing of steam turbines for the purpose of obtaining the level of performance with a minimum uncertainty. Only the relevant portion of this code needs to process any individual case, In some case the procedure is simple. However, in complex turbines or complex operation modes, more procedures are required to test the involved provisions. Anyway, to measure the steam quality in the Wolsong PHWR with 4 SGs in Korea by the methods in the section ''Measure of steam quality methods'' of ANSI/ASME PTC 6, the result was not good though the steam generators are efficient. So, the new testing method was developed and the sophisticated equation of steam quality was introduced and uses the nonradioactive chemical tracer, Lithium hydroxide(LiOH) instead of the radioactive tracer, Na-24. (author)

Broadcast Journalism Education and the Capstone Experience

Science.gov (United States)

Tanner, Andrea; Forde, Kathy Roberts; Besley, John C.; Weir, Tom

2012-01-01

This study assesses the current state of the television news capstone experience in accredited journalism and mass communication programs in the United States. Specifically, the authors employed a mixed-methods approach, interviewing 20 television news capstone instructors and conducting an analysis of broadcast journalism curriculum information…

An adaptive sampling method for variable-fidelity surrogate models using improved hierarchical kriging

Science.gov (United States)

Hu, Jiexiang; Zhou, Qi; Jiang, Ping; Shao, Xinyu; Xie, Tingli

2018-01-01

Variable-fidelity (VF) modelling methods have been widely used in complex engineering system design to mitigate the computational burden. Building a VF model generally includes two parts: design of experiments and metamodel construction. In this article, an adaptive sampling method based on improved hierarchical kriging (ASM-IHK) is proposed to refine the improved VF model. First, an improved hierarchical kriging model is developed as the metamodel, in which the low-fidelity model is varied through a polynomial response surface function to capture the characteristics of a high-fidelity model. Secondly, to reduce local approximation errors, an active learning strategy based on a sequential sampling method is introduced to make full use of the already required information on the current sampling points and to guide the sampling process of the high-fidelity model. Finally, two numerical examples and the modelling of the aerodynamic coefficient for an aircraft are provided to demonstrate the approximation capability of the proposed approach, as well as three other metamodelling methods and two sequential sampling methods. The results show that ASM-IHK provides a more accurate metamodel at the same simulation cost, which is very important in metamodel-based engineering design problems.

A Case Study: The Ethics of "New Journalism."

Science.gov (United States)

Brown, Donal

1986-01-01

Offers a method for teaching students about ethical journalism and new journalism using a favorite short story and asking questions such as "How is truth in fiction different from the truth in a news story?" (SRT)

Journal of Technology and Education in Nigeria: About this journal

African Journals Online (AJOL)

Journal of Technology and Education in Nigeria: About this journal. Journal Home > Journal of Technology and Education in Nigeria: About this journal. Log in or Register to get access to full text downloads.

East and Central African Journal of Surgery: About this journal

African Journals Online (AJOL)

East and Central African Journal of Surgery: About this journal. Journal Home > East and Central African Journal of Surgery: About this journal. Log in or Register to get access to full text downloads.

Ethiopian Journal of Business and Economics (The): About this journal

African Journals Online (AJOL)

Ethiopian Journal of Business and Economics (The): About this journal. Journal Home > Ethiopian Journal of Business and Economics (The): About this journal. Log in or Register to get access to full text downloads.

Zagazig Journal of Occupational Health and Safety: About this journal

African Journals Online (AJOL)

Zagazig Journal of Occupational Health and Safety: About this journal. Journal Home > Zagazig Journal of Occupational Health and Safety: About this journal. Log in or Register to get access to full text downloads.

Journal of Computer Science and Its Application: About this journal

African Journals Online (AJOL)

Journal of Computer Science and Its Application: About this journal. Journal Home > Journal of Computer Science and Its Application: About this journal. Log in or Register to get access to full text downloads.

Nigeria Journal of Pure and Applied Physics: About this journal

African Journals Online (AJOL)

Nigeria Journal of Pure and Applied Physics: About this journal. Journal Home > Nigeria Journal of Pure and Applied Physics: About this journal. Log in or Register to get access to full text downloads.

Journal of Youth Research

Directory of Open Access Journals (Sweden)

Dilek Solay

2013-12-01

Full Text Available Journal was published by Turkey Ministry of Youth and Sports for young people in order to support academic studies which is semi annual and articles submitted for “blind referee” method.

Pramana – Journal of Physics | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics. M Eslami. Articles written in Pramana – Journal of Physics. Volume 81 Issue 2 August 2013 pp 225-236 Research Articles. Exact solutions of some nonlinear partial differential equations using functional variable method · A Nazarzadeh M Eslami M Mirzazadeh · More Details ...

Open Access Journal Policies: A Systematic Analysis of Radiology Journals.

Science.gov (United States)

Narayan, Anand; Lobner, Katie; Fritz, Jan

2018-02-01

The open access movement has pushed for greater access to scientific knowledge by expanding access to scientific journal articles. There is limited information about the extent to which open access policies have been adopted by radiology journals. We performed a systematic analysis to ascertain the proportion of radiology journals with open access options. A search was performed with the assistance of a clinical informationist. Full and mixed English-language diagnostic and interventional radiology Web of Science journals (impact factors > 1.0) were included. Nuclear medicine, radiation oncology, physics, and solicitation-only journals were excluded. Primary outcome was open access option (yes or no) with additional outcomes including presence or absence of embargo, complete or partial copyright transfer, publication fees, and self-archiving policies. Secondary outcomes included journal citations, journal impact factors, immediacy, Eigenfactor, and article influence scores. Independent double readings were performed with differences resolved by consensus, supplemented by contacting editorial staff at each journal. In all, 125 journals were identified; review yielded 49 journals (39%, mean impact factor of 2.61). Thirty-six of the journals had open access options (73.4%), and four journals were exclusively open access (8.2%). Twelve-month embargoes were most commonly cited (90.6%) with 28.6% of journals stating that they did not require a complete transfer of copyright. Prices for open access options ranged from $750 to $4,000 (median $3,000). No statistically significant differences were found in journal impact measures comparing journals with open access options to journals without open access options. Diagnostic and interventional radiology journals have widely adopted open access options with a few radiology journals being exclusively open access. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

The Importance of Nutrition Journal Publication

Directory of Open Access Journals (Sweden)

Saptawati Bardosono

2017-09-01

. Knowledge of nutrition; which includes community, clinical, and critical care nutrition, is constantly growing. Therefore, the needs of journal submissions and reference searches continue to increase. In this digital era, the web has greatly reduced the barriers for communicating scientific output.1 One of many methods of publishing journals online is open access (OA. This is a method of publishing peer-reviewed journals and articles in the internet. This model of publishing can be freely accessed and read.2 In Indonesia, there are still only few open accessed journal publications, especially regarding nutrition-related knowledge. Considering the importance of journal publications, INA establishes World Nutrition Journal as an open access journal for the expansion of nutrition-related   knowledge and acts as a media for authors to publish their researches. World Nutrition Journal (abbreviated as WNJ is the peer-reviewed, world scale scientific journal of community, clinical, and critical care nutrition. It is the official journal of Indonesian Nutrition Association.  As a brand new journal, WNJ’s team haveroles to achieve standard requirementsof an International Journal. Recently, WNJ’s ISSN has been registered from LIPI (Lembaga Ilmu Pengetahuan Indonesia or Indonesian Science Institution, and has become a member of Crossref for Metadata and Similarity Check. Our goals are to publish high standard articles which are available to be tracked and cited by International scientists, as well as being indexed in Scopus, a bibliographic database containing abstracts and citations for academic journal articles. We do realize our first issue of World Nutriton Journal is a starting point and a stepping stone to develop our journal to be more credible and havemore impact factors. We will strive to polish and achieve our targets to be fulfilled for our next edition.

Technical basis for the extension of ASME Code Case N-494 for assessment of austenitic piping

International Nuclear Information System (INIS)

Bloom, J.M.

1995-01-01

In 1990, the ASME Boiler and Pressure Vessel Code for Nuclear Components approved Code Case N-494 as an alternative procedure for evaluating laws in Light Water Reactor alterative procedure for evaluating flaws in Light Water Reactor (LWR) ferritic piping. The approach is an alternative to Appendix H of the ASME Code and alloys the user to remove some unnecessary conservatism in the existing procedure by allowing the use of pipe specific material properties. The Code Case is an implementation of the methodology of the Deformation Plasticity Failure Assessment diagram (DPFAD). The key ingredient in the application of DPFAD is that the material stress-strain curve must be in the format of a simple power law hardening stress-strain curve such as the Ramberg-Osgood (R-O) model. Ferritic materials can be accurately fit by the R-O model and, therefore, it was natural to use the DPFAD methodology for the assessment of LWR ferritic piping. An extension of Code Case N-494 to austenitic piping required a modification of the existing DPFAD methodology. The Code Case N-494 approach was revised using the PWFAD procedure in the same manner as in the development of the original N-494 approach for ferritic materials. A lower bound stress-strain curve was used to generate a PWFAD curve for the geometry of a part-through wall circumferential flaw in a cylinder under tension. Earlier work demonstrated that a cylinder under axial tension with a 50% flaw depth, 90 degrees in circumference, and radius to thickness of 10, produced a lower bound FAD curve. Validation of the new proposed Code Case procedure for austenitic piping was performed using actual pipe test data. Using the lower bound PWFAD curve, pipe test results were conservatively predicted. The resultant development of ht PWFAD curve for austenitic piping led to a revision of Code Case N-494 to include a procedure for assessment of flaws in austenitic piping

Simplified method evaluation for piping elastic follow-up

International Nuclear Information System (INIS)

Severud, L.K.

1983-05-01

A proposed simplified method for evaluating elastic follow-up effects in high temperature pipelines is presented. The method was evaluated by comparing the simplified analysis results with those obtained from detailed inelastic solutions. Nine different pipelines typical of a nuclear breeder reactor power plant were analyzed; the simplified method is attractive because it appears to give fairly accurate and conservative results. It is easy to apply and inexpensive since it employs iterative elastic solutions for the pipeline coupled with the readily available isochronous stress-strain data provided in the ASME Code

The application of RCM to ASME code requirements for in-service testing

International Nuclear Information System (INIS)

Rowley, C.W.

1990-01-01

This paper reports that the high reliability of nuclear power plant systems and components is highly important for both nuclear safety and electrical power production economics. The optimum operating performance of these plant systems and components is heavily dependent on the original or modified design for its inherent reliability and the appropriate trade-off in preventive and corrective maintenance for its developed reliability. In developing this optimum operating performance goal, the plant staff could rely solely on the experience of its personnel. However using this internal subjective approach, the average nuclear power availability has been far less than 80%. Obviously the production economics of a nuclear power plant is the province of the owner-operator, but the safety system and component performance impacts the entire industry. Hence the nuclear industry needs to have in-service testing requirements that maintain the necessary safety standards. Historically the ASME Inservice Testing Code has been a vehicle for defining some of those necessary safety standards, such as inservice testing of pumps, valves, and snubbers. The nuclear industry needs to expand the code testing to include all the systems that affect these necessary safety standards

An Automated Approach for Ranking Journals to Help in Clinician Decision Support

Science.gov (United States)

Jonnalagadda, Siddhartha R.; Moosavinasab, Soheil; Nath, Chinmoy; Li, Dingcheng; Chute, Christopher G.; Liu, Hongfang

2014-01-01

Point of care access to knowledge from full text journal articles supports decision-making and decreases medical errors. However, it is an overwhelming task to search through full text journal articles and find quality information needed by clinicians. We developed a method to rate journals for a given clinical topic, Congestive Heart Failure (CHF). Our method enables filtering of journals and ranking of journal articles based on source journal in relation to CHF. We also obtained a journal priority score, which automatically rates any journal based on its importance to CHF. Comparing our ranking with data gathered by surveying 169 cardiologists, who publish on CHF, our best Multiple Linear Regression model showed a correlation of 0.880, based on five-fold cross validation. Our ranking system can be extended to other clinical topics. PMID:25954382