WorldWideScience

Sample records for metallurgy fibre

  1. Metallurgy Department

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration...

  2. Implantation metallurgy

    International Nuclear Information System (INIS)

    Picraux, S.T.

    1975-01-01

    Important changes in the near-surface physical properties of metals were obtained by high-fluence ion implantation. Recently there have been an increasing number of studies of the behavior of implanted species with the aim of understanding the detailed physical processes that occur in an implanted metal layer. A key aspect of these implantation metallurgy studies has been the ability to form uniquely controlled systems in the near-surface regions of metals that can be studied with accurate depth resolution. Metallurgical parameters that may be difficult or impossible to obtain by other means can be measured. Also, parameters that depend on the implantation process, due to the athermal introduction of atoms and defects can be determined. Thus the dual objective of implantation metallurgy is to obtain information to improve understanding of the microscopic aspects of metallurgy and to understand how to form controlled new metallurgical systems. Examples of parameters studied include implanted impurity location, diffusion, enhanced diffusion, solubility, precipitation, and dissolution. (auth)

  3. Metallurgy Department publications 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1989-08-01

    A presentation (including abstracts) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1988 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following catagories: Publications, Lectures and Poster Presentations. (author)

  4. Metallurgy Department publications 1989

    International Nuclear Information System (INIS)

    Horsewell, A.

    1990-08-01

    All publiclations by the staff of the Metallurgy Department during 1989 are listed. This list is divided into three sections as follows: Publications (journal and conference papers, reports); Lectures (public lecture presentations) and Posters (poster presentations at conferences and symposia). Abstracts are included. (author)

  5. Extractive metallurgy. Recent advances

    International Nuclear Information System (INIS)

    Stevenson, E.J.

    1977-01-01

    Detailed technical information derived from patents issued since 1975 on extractive metallurgy is presented. In part one, concerning copper, the major areas covered are: smelting and roasting; acid leaching; ammonia leach processes; cuprous chloride and ferric chloride; and recovery of copper values from solution. Part two covers other metals, including: nickel and cobalt; ocean floor nodules; lead, zinc, molybdenum and manganese; precious metals; and uranium titanium, tantalum, rhenium, gallium, and other metals

  6. Current programmes of Metallurgy Division (1991)

    International Nuclear Information System (INIS)

    1991-01-01

    Current research and development programmes of the Metallurgy Division are listed under the headings: 1)Thrust Areas, 2)High Temperature Materials Section, 3)Chemical Metallurgy Section, 4)Metallurgical Thermochemistry Section, 5)Physical Metallurgy Section, 6)Mechanical Metallurgy Section, 7)Corrosion Metallurgy Section, 8)Electrochemical Science and Technology Section, 9)Ceramics Section, and 10)Fabrication and Maintenance Group. A list of equipment in the Division and a list of sciientific personnel of the Division are also given. (M.G.B.)

  7. Lithium extractive metallurgy

    International Nuclear Information System (INIS)

    Josa, J.M.; Merino, J.L.

    1985-01-01

    The Nuclear Fusion National Program depends on lithium supplies. Extractive metallurgy development is subordinate to the localization and evaluation of ore resources. Nowadays lithium raw materials usable with present technology consist of pegmatite ore and brine. The Instituto Geologico y Minero Espanol (IGME) found lepidolite, ambligonite and spodrimene in pegmatite ores in different areas of Spain. However, an evaluation of resources has not been made. Different Spanish surface and underground brines are to be sampled and analyzed. If none of these contain significant levels of lithium, the Junta de Energia Nuclear (JEN) will try an agreement with IGME for ENUSA (Empresa Nacional del Uranio, S.A.) to explore pegmatite-ore bodies from different locations. Different work stages, laboratory tests, pilots plants tests and commercial plant, are foreseen, if the deposits are found. (author)

  8. The extractive metallurgy of gold

    Energy Technology Data Exchange (ETDEWEB)

    Kongolo, K.; Mwema, M.D. [University of Lubumbashi, Zaire, Gecamines Metallurgical Research Centre, Likasi, Zaire, c/o Gecamines Brussels (Belgium)

    1998-12-15

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied.

  9. The extractive metallurgy of gold

    International Nuclear Information System (INIS)

    Kongolo, K.; Mwema, M.D.

    1998-01-01

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied

  10. Physical metallurgy of nickel aluminides

    Indian Academy of Sciences (India)

    A description of the important physical metallurgy aspects of Ni$_3Al and NiAl encompassing structure, crystallographic defects, slip systems and phase stability has been presented in this article. The microstructures generated in the two alloys by conventional as well as novel processing techniques have been discussed.

  11. Fibre tracking

    International Nuclear Information System (INIS)

    Gaillard, J.M.

    1994-03-01

    A large-size scintillating plastic fibre tracking detector was built as part of the upgrade of the UA2 central detector at the SPS proton-antiproton collider. The cylindrical fibre detector of average radius of 40 cm consisted of 60000 plastic fibres with an active length of 2.1 m. One of the main motivations was to improve the electron identification. The fibre ends were bunched to be coupled to read-out systems of image intensifier plus CCD, 32 in total. The quality and the reliability of the UA2 fibre detector performance exceeded expectations throughout its years of operation. A few examples of the use of image intensifiers and of scintillating fibres in biological instrumentation are described. (R.P.) 11 refs., 15 figs., 2 tabs

  12. Metallurgi for Ingeniører

    DEFF Research Database (Denmark)

    Pedersen, Jan

    Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962......Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962...

  13. Optical fibres

    CERN Multimedia

    1992-01-01

    These optical fibres are used to detect particles passing through in bunches. Made from scintillating material, the fibres glow when a high energy particle passes through them. These detectors are known as spaghetti detectors and are used to measure the energy of particles.

  14. The metallurgy, science and engineering

    International Nuclear Information System (INIS)

    Pineau, A.; Quere, Y.

    2011-01-01

    Metallurgy, the science of metals and the technical discipline concerned with the production, shaping and assembling of metals, is one of the major assets of European economy. The French metallurgy industry - from producers (steel, light alloys, ...) to users (car, aviation, nuclear industries, ...) -- has achieved in many of its sectors a world-class level of excellence, based on high-quality research centres that are recognized both for their theoretical and experimental academic work. By contrast, public research is insufficiently concerned with engineering. In 2004, this industry employed 1 800 000 persons, 220 000 of which worked as engineers and managers in 45 000 companies, with a turnover of 420 billion euros. This state of grace is starting to decline. We are undergoing, in this sector as in others, a de-industrialization that affects upstream activities: courses in these disciplines, which have been previously outstanding, have partially disappeared; laboratories have shrunk; expertise has been dispersed; students are staying away from a discipline they consider 'unfruitful', like many other engineering sciences. Simultaneously, further up in this sector, decision centres have moved away from production centres and away from our country. France still maintains a few important R and D centres within international groups in spite of France's decreasing weight in world production. However, these groups see the future of R and D as being centred in the emerging countries (China, India...). The main users (transport, energy, ...) are losing their experts as are the technical centres on which rely a large network of small and medium businesses. The consequences are alarming in view of the already noticeable loss of technical control. This trend can and must be reversed. Because of its presence in many industrial sectors and its excellence, metallurgy - including both research and industry - is an essential activity in which France should remain a major player

  15. Progress report of the Metallurgy Group

    International Nuclear Information System (INIS)

    Sundaram, C.V.; Moorthy, V.K.

    1975-01-01

    The activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the year 1974 are reported under six sections, namely: ore dressing; extractive metallurgy; ceramics; physical metallurgy; corrosion and electrometallurgy, and radiometallurgy. The developmental programme is not only concerned with materials of nuclear interest such as uranium, thorium, plutonium, zirconium, niobium and beryllium, but also other materials of national interest such as titanium, tantalum, ceramics, corrosion-resistant alloys etc. In addition to the laboratory studies, collaborative work has also been undertaken with other units of the Department of Atomic Energy. (A.K.)

  16. Dietary Fibre

    NARCIS (Netherlands)

    Kamp, van der J.W.; Asp, N.G.; Miller Jones, J.; Schaafsma, G.

    2004-01-01

    In this book invited expert scientists of leading research groups all over the world will address the following issues: Definitions, health claims and new challenges, Analytical tools, technological aspects and applications, Health Benefits of dietary fibre, including both authoritative generic

  17. [Respiratory diseases in metallurgy production workers].

    Science.gov (United States)

    Shliapnikov, D M; Vlasova, E M; Ponomareva, T A

    2012-01-01

    The authors identified features of respiratory diseases in workers of various metallurgy workshops. Cause-effect relationships are defined between occupational risk factors and respiratory diseases, with determining the affection level.

  18. Structural Description of Powder Metallurgy Prepared Materials

    Czech Academy of Sciences Publication Activity Database

    Michalcová, A.; Vojtěch, D.; Kubatík, Tomáš František; Novák, P.; Dvořák, P.

    2014-01-01

    Roč. 14, č. 3 (2014), s. 359-362 ISSN 1213-2489. [Mezinárodní konference „Mikroskopie a nedestruktivní zkoušení materiálů/3./. Litoměřice, 22.10.2014-24.10.2014] Institutional support: RVO:61389021 Keywords : SPS * Intermetallics * powder metallurgy Subject RIV: JG - Metallurgy http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XIV_2014-3.pdf

  19. Advanced powder metallurgy aluminum alloys and composites

    Science.gov (United States)

    Lisagor, W. B.; Stein, B. A.

    1982-01-01

    The differences between powder and ingot metallurgy processing of aluminum alloys are outlined. The potential payoff in the use of advanced powder metallurgy (PM) aluminum alloys in future transport aircraft is indicated. The national program to bring this technology to commercial fruition and the NASA Langley Research Center role in this program are briefly outlined. Some initial results of research in 2000-series PM alloys and composites that highlight the property improvements possible are given.

  20. Powder metallurgy development at SRL

    International Nuclear Information System (INIS)

    Peacock, H.B.

    1978-01-01

    Fuel for Savannah River Plant (SRP) reactors consists of extruded tubes with aluminum--uranium alloy cores clad with 8001 aluminum. The 235 U in the fuel is periodically recovered and recycled in new fuel assemblies. The buildup of 236 U in the enriched uranium requires increased total uranium contents to maintain reactivity in existing assembly designs. High level waste production from these tubes is proportional to the aluminum content; therefore, appreciable radioactive waste reductions result from lower aluminum--uranium ratios and thinner clad tubes. The casting process now used for fuel cores is limited to below 40 wt % U because of the reduced fabricability of high uranium alloys. To increase tube loading and reduce aluminum, the U 3 O 8 -Al powder metallurgy (P/M) process for fuel tubes is under development. Several fabricaion and irradiaion tests have been made using production conditions. Both small scale and production tests carried out at SRL for high-density P/M fuel development are discussed

  1. Metallurgy department progress report for the period 1 January to 31 December 1979

    International Nuclear Information System (INIS)

    1980-07-01

    The activities of the Metallurgy Department at Risoe during 1979 are described. The work is presented in four chapters: General material research, technology and materials development, fuel elements, non-destructive testing. An article on wingblades of glass fibre reinforced polyester for a 630 kW windturbine is also included. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1979 is included. (author)

  2. Flow mechanisms in creep of a short-fibre AZ91 alloy-based composite

    Czech Academy of Sciences Publication Activity Database

    Pahutová, Marie; Sklenička, Václav; Kuchařová, Květa; Svoboda, Milan; Langdon, T. G.

    43 2005, č. 1 (2005), s. 34-44 ISSN 0023-432X R&D Projects: GA ČR(CZ) GA106/03/0901 Institutional research plan: CEZ:AV0Z20410507 Keywords : AZ91 magnesium alloy * metal matrix composite * short fibre reinforcement Subject RIV: JG - Metallurgy Impact factor: 0.973, year: 2005

  3. Current programmes on physical metallurgy and related areas in BARC

    International Nuclear Information System (INIS)

    1994-01-01

    Current research and development programmes on physical metallurgy and related areas from the following Divisions of Bhabha Atomic Research Centre are included in this report : Atomic Fuels Division, High Pressure Physics Division, Metallurgy Division, Radio Metallurgy Division, Solid State Physics Division. Important publications corresponding to each activity have also been listed. (author)

  4. Ideate about building green mine of uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Shi Zuyuan

    2012-01-01

    Analysing the current situation of uranium mining and metallurgy; Setting up goals for green uranium mining and metallurgy, its fundamental conditions, Contents and measures. Putting forward an idea to combine green uranium mining and metallurgy with the state target for green mining, and keeping its own characteristics. (author)

  5. Powder metallurgy development at SRL

    International Nuclear Information System (INIS)

    Peacock, H.B.

    1993-01-01

    The Savannah River Laboratory (SRL) is developing a powder metallurgy (P/M) process for manufacturing reactor-grade fuel tubes containing high wt % U 3 O 8 -Al cores clad with 8001 aluminum. The P/M cores are made by isostatic compaction. They are assembled in billets, outgassed, and hot-extruded using conventional coextrusion techniques. Cores have been compacted with up to 100% U3O 8 and tubes extruded with 80 wt % oxide cores. Irradiation tests have been made using P/M core tubes in the Savannah River reactors. These tubes contained U 3 O 8 concentrations up to 59 wt % and no significant swelling or blistering occurred. The tubes were irradiated to ∼ 40% burnup or 1.6x10 21 fissions/cc of core. This report discusses both small-scale and production tests for high-density P/M fuel development. The purpose of the P/M development program at SRL is to: determine the maximum U 3 O 8 content that can be fabricated into thin wall tubes, irradiate high-density tubes to high burnup and assess irradiation and dimensional stability, continue metal forming studies for extrusion and drawing, and evaluate hydrostatic extrusion and hydrostatically assisted drawing of P/M core tubes. Experimental results of testing the fuel assemblies performance so far indicate that: cores containing fine (-325 mesh) U 3 O 8 and aluminum powders can be made practically free of high-density areas using the outlined P/M pre blending and sieving techniques. U 3 O 8 -Al cores can be isostatically compacted with up to 100 wt U 3 O 8 and tubes successfully extruded with up to 80 wt oxide; fission gas blistering of U 3 O 8 -Al P/M tubes as indicated by the blister tests is a function of fissions/cc of U 3 O 8 in the core; Decreasing the fission density of oxide increases the threshold temperature for blister formation; U 3 O 8 -Al P/M fuel tubes with up to 59 wt U 3 O 8 have been successfully irradiated in SRP reactor to 1.6 x 10 21 fissions/cc of core or 7 x 10 20 fissions/cc of U 3 O 8 small

  6. Scintillating fibres

    International Nuclear Information System (INIS)

    Nahnhauer, R.

    1990-01-01

    In the search for new detector techniques, scintillating fibre technology has already gained a firm foothold, and is a strong contender for the extreme experimental conditions of tomorrow's machines. Organized by a group from the Institute of High Energy Physics, Berlin-Zeuthen, a workshop held from 3-5 September in the nearby village of Blossin brought together experts from East and West, and from science and industry

  7. Biennial activity report of metallurgy programme for 1987 and 1988

    International Nuclear Information System (INIS)

    Shanmugam, V.; Rao, B.P.C.; Bhanu Sankara Rao, K.; Muralidharan, P.; Bhaduri, A.K.; Kuppusami, P.; Shyamsunder, M.T.; Sampath, N.; Sreedharan, O.M.

    1990-01-01

    The research and development (R and D) activities in the field of metallurgy at Indira Gandhi Centre for Atomic Research, Kalpakkam during 1987-1988 are reported in the form of individual summaries arranged under headings : (1) Mechanical Metallurgy Section, (2) Physical Metallurgy Section, (3) Chemical Metallurgy Section, (4) Materials Technology Section, (5) Division for PIE and NDT Development and (6) Quality Engineering Section. A list of publications by the staff scientists working in the field of metallurgy during report period is given in one of the appendices. (author). figs., tabs

  8. Metallurgy department publications and lectures 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1988-04-01

    A presentation (including abstract) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1987 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following categories: Publications, Lectures and Poster Presentations. (author)

  9. Investigations to problems of the implantation metallurgy

    International Nuclear Information System (INIS)

    Rauschenbach, B.

    1987-01-01

    Basing on processes and effects caused ion implantation of metals a review is given about the problems of the implantation metallurgy. Techniques of high-fluence ion implantation and ion beam mixing are generally confined. These techniques change the structure and the chemical composition in the near of the surface of metals. The application of these methods is demonstrated on series of examples. (author)

  10. Powder-Metallurgy Process And Product

    Science.gov (United States)

    Paris, Henry G.

    1988-01-01

    Rapid-solidification processing yields alloys with improved properties. Study undertaken to extend favorable property combinations of I/M 2XXX alloys through recently developed technique of rapid-solidification processing using powder metallurgy(P/M). Rapid-solidification processing involves impingement of molten metal stream onto rapidly-spinning chill block or through gas medium using gas atomization technique.

  11. Development and prospect of china uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Que Weimin; Wang Haifeng; Niu Yuqing; Gu Wancheng; Zhang Feifeng

    2007-01-01

    The development of industry of uranium mining and metallurgy in China has been reviewed generally, emphasizing on investigation approaches and application levels of uranium mining technologies such as in-situ leaching, heap leaching, stope leaching: on the basis of analysis on status of uranium mining and metallurgy and problems existed, also considering the specific features of deposit resources, the development orientation of uranium mining and metallurgy in China is pointed out. The industry of China uranium mining and metallurgy is faced to new opportunity of development and challenge in 21st century, the only way to realize sustainable development of uranium mining and metallurgy and harmonious development between economy and environment is to develop new technology on mining, ore beneficiation and metallurgy, increase the utilization level of uranium resources, low down impact on environment caused by mining and metallurgy. (authors)

  12. Computational thermodynamics in electric current metallurgy

    DEFF Research Database (Denmark)

    Bhowmik, Arghya; Qin, R.S.

    2015-01-01

    A priori derivation for the extra free energy caused by the passing electric current in metal is presented. The analytical expression and its discrete format in support of the numerical calculation of thermodynamics in electric current metallurgy have been developed. This enables the calculation...... of electric current distribution, current induced temperature distribution and free energy sequence of various phase transitions in multiphase materials. The work is particularly suitable for the study of magnetic materials that contain various magnetic phases. The latter has not been considered in literature....... The method has been validated against the analytical solution of current distribution and experimental observation of microstructure evolution. It provides a basis for the design, prediction and implementation of the electric current metallurgy. The applicability of the theory is discussed in the derivations....

  13. Powder metallurgy bearings for advanced rocket engines

    Science.gov (United States)

    Fleck, J. N.; Killman, B. J.; Munson, H.E.

    1985-01-01

    Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified.

  14. Metallurgy Department. Annual progress report for 1989

    International Nuclear Information System (INIS)

    Horsewell, A.; Hansen, N.

    1990-07-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1989 are described. The work is presented in three chapters: Materials Science, Materials Engineering and Materials Technology. A survey is given of the Department's participation in international collaboration and of its acitivities within eduation and training. Furthermore, the main figures outlining the funding and expenditure of the Department are given. Lists of staff members, visiting scientists, publicaltions, lectures and poster presentations are included. (author) 90 refs

  15. Metallurgy Department annual progress report for 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1988-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1987 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Departments's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. 38 ills. (author)

  16. Metallurgy Department. Annual progress report for 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1989-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1988 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Department's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. (author) 36 ills., 81 refs

  17. Low-Cobalt Powder-Metallurgy Superalloy

    Science.gov (United States)

    Harf, F. H.

    1986-01-01

    Highly-stressed jet-engine parts made with less cobalt. Udimet 700* (or equivalent) is common nickel-based superalloy used in hot sections of jet engines for many years. This alloy, while normally used in wrought condition, also gas-atomized into prealloyed powder-metallurgy (PM) product. Product can be consolidated by hot isostatically pressing (HIPPM condition) and formed into parts such as turbine disk. Such jet-engine disks "see" both high stresses and temperatures to 1,400 degrees F (760 degrees C).

  18. Borax as a lubricant in powder metallurgy

    Directory of Open Access Journals (Sweden)

    Héctor Geovanny Ariza-Suarez

    2014-12-01

    were compacted at 700 MPa in a uniaxial press of 15 tons. DSC-TGA analysis of the mixture with borax was realized. The specimens were sintered in a plasma reactor at 1000 for 30 minutes, with a combined atmosphere of hydrogen and argon. Microhardness and density of the sintered samples was haracterized. XRD analysis was realized to detect possible compounds formation by interaction of borax. This paper shows that borax can be used as a lubricant in powder metallurgy.

  19. Biaxially textured articles formed by powder metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-07-29

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  20. Biaxially textured articles formed by power metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-26

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  1. Preparation of nitinol by non-conventional powder metallurgy techniques

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Salvetr, P.; Průša, F.; Drahokoupil, Jan; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2015-01-01

    Roč. 31, č. 15 (2015), s. 1886-1893 ISSN 0267-0836 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:68378271 ; RVO:61389021 Keywords : shape memory alloys * SHS process * SEM * powder metallurgy Subject RIV: JG - Metallurgy Impact factor: 1.008, year: 2015

  2. Metallurgy and Heat Treating. Welding Module 7. Instructor's Guide.

    Science.gov (United States)

    Missouri Univ., Columbia. Instructional Materials Lab.

    This guide is intended to assist vocational educators in teaching a three-unit module in metallurgy and heat treating. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The basic principles of metallurgy and heat treatment and techniques for…

  3. Metallurgy of high-silicon steel parts produced using Selective Laser Melting

    International Nuclear Information System (INIS)

    Garibaldi, Michele; Ashcroft, Ian; Simonelli, Marco; Hague, Richard

    2016-01-01

    The metallurgy of high-silicon steel (6.9%wt.Si) processed using Selective Laser Melting (SLM) is presented for the first time in this study. High-silicon steel has great potential as a soft magnetic alloy, but its employment has been limited due to its poor workability. The effect of SLM-processing on the metallurgy of the alloy is investigated in this work using microscopy, X-Ray Diffraction (XRD) and Electron Backscatter Diffraction (EBSD). XRD analysis suggests that the SLM high-silicon steel is a single ferritic phase (solid solution), with no sign of phase ordering. This is expected to have beneficial effects on the material properties, since ordering has been shown to make silicon steels more brittle and electrically conductive. For near-fully dense samples, columnar grains with a high aspect ratio and oriented along the build direction are found. Most importantly, a <001> fibre-texture along the build direction can be changed into a cube-texture when the qualitative shape of the melt-pool is altered (from shallow to deep) by increasing the energy input of the scanning laser. This feature could potentially open the path to the manufacture of three-dimensional grain-oriented high-silicon steels for electromechanical applications.

  4. Microgel polymer composite fibres

    OpenAIRE

    Kehren, Dominic

    2014-01-01

    In this thesis some novel ideas and advancements in the field of polymer composite fibres, specifically microgel-based polymer composite fibres have been achieved. The main task was to investigate and understand the electrospinning process of microgels and polymers and the interplay of parameter influences, in order to fabricate reproducible and continuously homogenous composite fibres. The main aim was to fabricate a composite material which combines the special properties of polymer fibres ...

  5. Titanium surgical implants processed by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, M.V. de [INT-DMCM, Inst. Nacional de Tecnologia, Rio de Janeiro, RJ (Brazil); Pereira, L.C. [Programa de Eng. de Materiais e Metalurgica, UFRJ-COPPE (Brazil); Schwanke, C.M.; Schaeffer, L. [Centro de Tecnologia- LdTM-INT-DMCM, UFRGS, Venezuela, CEP, Rio de Janeiro, RJ (Brazil)

    2001-07-01

    Due to their low density coupled with excellent corrosion resistance and good mechanical properties, titanium and titanium alloys have been widely used for surgical implants. They have also a relatively low young's modulus, allowing a good load transfer to the bone. The elastic modulus difference between metallic implant material and bone is large, which can lead to a fracture of the implant. To solve this problem, many implants for artificial joint and dental applications have been produced by powder metallurgy routes, obtaining a porous material with an even lower young's modulus than that of the bulk titanium. This porous structure allows bone ingrowth, as the osseous tissue invade the holes of the porous material while growing and adheres to it. Besides, near net shape technologies like powder metallurgy and injection molding techniques, can reduce the components high costs due to machining final steps, also providing a fine, uniform grain structure and lack of texture and segregation. This work outlines the characteristics, properties and some of the powder routes for producing titanium surgical implants and implant porous coatings. (orig.)

  6. Fun with Optical Fibres

    Science.gov (United States)

    Alti, Kamlesh

    2017-01-01

    Optical fibres play a very crucial role in today's technologies. Academic courses in optical fibres start at the undergraduate level. Nevertheless, student's curiosity towards optical fibres starts from the school level. In this paper, some fun experiments have been designed for both school and college students, which have some concrete…

  7. Microstructured polymer optical fibres

    CERN Document Server

    Large, Maryanne; Barton, Geoff; van Eijkelenborg, Martijn A

    2008-01-01

    Microstructured Polymer Optical Fibres describes the optical properties of microstructured fibres, how they are made and modelled, and outlines some potential applications. These applications include areas where polymer fibres are already used, such as high-data rate transmission for Fibre-to-the Home or within cars, as well as completely new areas such as the photonic bandgap transmission of ""difficult"" wavelengths. Emphasising a conceptual understanding of the underlying physics, Microstructured Polymer Optical Fibres is clearly written, and includes numerous illustrations. It provides an

  8. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end......-directional arrangement. The fibre illumination system comprises a fibre illumination module of the above-mentioned type. By the invention, daylight may be exploited for the illumination of remote interior spaces of buildings in order to save energy, and improve the well-being of users in both housing and working...

  9. Promoting energy conservation in China's metallurgy industry

    International Nuclear Information System (INIS)

    Lin, Boqiang; Du, Zhili

    2017-01-01

    China is undergoing rapid industrialization and urbanization, with consequent dramatic increase in energy demand. Given energy scarcity, environmental pollution, energy security and energy cost constraints, energy conservation will be the major strategy in China's transition to a low-carbon economy. Since the metallurgy industry is a main sector of energy consumption, the efficiency of energy conservation in this industry will affect the future prospects of energy savings. This paper analyzes the energy conservation potential of China's metallurgy industry. First, seemingly unrelated regression method is applied to investigate the relationship between energy relative price, R&D input, enterprise ownership structure, enterprise scale and energy intensity of the metallurgy industry. Then, based on the SUR results, we use the scenario analysis method to predict energy consumption and savings potential in the industry in different scenarios. This paper provides references for China's government and metallurgy industry in formulating relevant energy conservation policies. - Highlights: • Seemingly unrelated regression method is applied to analyze the energy intensity of metallurgy industry. • We use the scenario analysis method to predict energy consuming and energy saving of Chinese metallurgy industry. • Provide references for China's government and metallurgy industry in formulating relevant energy conservation policies.

  10. Biennial activity report of Metallurgy Division for 1989 and 1990

    International Nuclear Information System (INIS)

    Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

    1993-01-01

    This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

  11. Chemistry and metallurgy in the Portuguese Empire

    Energy Technology Data Exchange (ETDEWEB)

    Habashi, F. [Laval Univ., Sainte-Foy, Quebec City, PQ (Canada)

    2000-10-01

    The foundation and expansion of the Portuguese Empire is sketched, with emphasis on the development of a new type of ship by Prince Henrique the Navigator (AD 1385-1460), known as the caravel. By virtue of its advanced design, it was capable of sailing the stormy seas at high speeds, and thereby was instrumental in extending Portuguese influence over vast territories in South America, Asia and Africa, extending Portuguese know-how in mining, metallurgy, chemistry and trade along with Christianity. The role played by the University of Coimbra, founded in 1306, and the contribution of the Brazilian Geological Survey, established in 1875, and of the School of Mines in Ouro Preto in Brazil in 1876, in the exploitation of the mineral wealth of the Portuguese colonies is chronicled.

  12. Thermogravimetric control of intermediate compounds in uranium metallurgy

    International Nuclear Information System (INIS)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-01-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs

  13. HIPPI and Fibre Channel

    International Nuclear Information System (INIS)

    Tolmie, D.E.

    1992-01-01

    The High-Performance Parallel Interface (HIPPI) and Fibre Channel are near-gigabit per second data communications interfaces being developed in ANSI standards Task Group X3T9.3. HIPPI is the current interface of choice in the high-end and supercomputer arena, and Fibre Channel is a follow-on effort. HIPPI came from a local area network background, and Fibre Channel came from a mainframe to peripheral interface background

  14. The metallurgy of superalloys part 2

    International Nuclear Information System (INIS)

    Abdelazim, M.E.; Hammad, F.H.

    1990-01-01

    This is part II of the report titled 'the metallurgy of superalloys'. It deals with the effect of heat treatment and operating conditions (thermal exposure and environment) on the mechanical properties of superalloys. The heat treatment is important in the development of superalloys through that it controls type, amount, size shape and distribution of the precipitate and the grain size of the matrix. The thermal exposure leads to reduction in the amount of the primary carbides and to precipitation of secondary carbides. Also it leads to the agglomeration and coarsening of gamma or the transformation of gamma phase to phase. The environment may lead to the internal oxidation, carburization, decarburization or sulphidization of the superalloys which may result in the degradation of their mechanical properties. This part gives also an example of applications of superalloys in the field of nuclear reactors especially high temperature-gas cooled reactors. Joined with this part a table which contains the major superalloys including its chemical analysis, creep rupture strength and some of its applications. 1 tab

  15. A major advance in powder metallurgy

    Science.gov (United States)

    Williams, Brian E.; Stiglich, Jacob J., Jr.; Kaplan, Richard B.; Tuffias, Robert H.

    1991-01-01

    Ultramet has developed a process which promises to significantly increase the mechanical properties of powder metallurgy (PM) parts. Current PM technology uses mixed powders of various constituents prior to compaction. The homogeneity and flaw distribution in PM parts depends on the uniformity of mixing and the maintenance of uniformity during compaction. Conventional PM fabrication processes typically result in non-uniform distribution of the matrix, flaw generation due to particle-particle contact when one of the constituents is a brittle material, and grain growth caused by high temperature, long duration compaction processes. Additionally, a significant amount of matrix material is usually necessary to fill voids and create 100 percent dense parts. In Ultramet's process, each individual particle is coated with the matrix material, and compaction is performed by solid state processing. In this program, Ultramet coated 12-micron tungsten particles with approximately 5 wt percent nickel/iron. After compaction, flexure strengths were measured 50 percent higher than those achieved in conventional liquid phase sintered parts (10 wt percent Ni/Fe). Further results and other material combinations are discussed.

  16. Fibre-concrete container

    International Nuclear Information System (INIS)

    2000-01-01

    In this leaflet the fibre-concrete container for radioactive wastes is described. The fibre container is made of fibre-concrete that contains cement, aggregate, sand, filter, flame-silica, super-plastificator, water and scattered metal fibres. The fibre-concrete container has a dice shape with outer dimension 1.7 x 1.7 x 1.7 m. It is mounted of a container body, a container cover and two caps. Total weight of container is 4,240 kg, maximum weight of loaded container do not must exceed 15,000 kg. The physical and mechanical properties of the fibre-concrete container are described in detail. The fibre-concrete container manufactured for storing of low and intermediate radioactive wastes. A fibre-concrete container utilization to store of radioactive wastes solves these problems: increase of stability of stored packages of radioactive waste; watertightness within 300 years at least; static stability of bearing space; better utilization of bearing spaces; insulation of radioactive waste in a case of seismic and geological event; increase of fire resistance; and transport of radioactive waste

  17. Photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Sanchez Bjarklev, Araceli

    Photonic crystal fibres represent one of the most active research areas today in the field of optics. The diversity of applications that may be addressed by these fibres and their fundamental appeal, by opening up the possibility of guiding light in a radically new way compared to conventional...... optical fibres, have spun an interest from almost all areas of optics and photonics. The aim of this book is to provide an understanding of the different types of photonic crystal fibres and to outline some of the many new and exciting applications that these fibres offer. The book is intended for both...... readers with a general interest in photonic crystals, as well as for scientists who are entering the field and desire a broad overview as well as a solid starting point for further specialized stuides. Teh book, therefore, covers bothe general aspects such as the link from classical optics to photonic...

  18. Copper alloys with improved properties: standard ingot metallurgy vs. powder metallurgy

    Directory of Open Access Journals (Sweden)

    Milan T. Jovanović

    2014-09-01

    Full Text Available Three copper-based alloys: two composites reinforced with Al2O3 particles and processed through powder metallurgy (P/M route, i.e. by internal oxidation (Cu-2.5Al composite and by mechanical alloying (Cu-4.7Al2O3 and Cu-0.4Cr-0.08Zr alloy produced by ingot metallurgy (vacuum melting and casting were the object of this investigation. Light microscope and scanning electron microscope (SEM equipped with electron X-ray spectrometer (EDS were used for microstructural characterization. Microhardness and electrical conductivity were also measured. Compared to composite materials, Cu-0.4Cr-0.08Zr alloy possesses highest electrical conductivity in the range from 20 to 800 ℃, whereas the lowest conductivity shows composite Cu-2.5Al processed by internal oxidation. In spite to somewhat lower electrical conductivity (probably due to inadequate density, Cu-2.5Al composite exhibits thermal stability enabling its application at much higher temperatures than materials processed by mechanical alloying or by vacuum melting and casting.

  19. FibreBags vs. FibreCaps for acid and neutral detergent fibre analysis

    OpenAIRE

    Koivisto , Jason

    2003-01-01

    International audience; A new procedure for determining acid detergent fibre and neutral detergent fibre (ADF and NDF) was developed to reduce the need for filtration and to allow for batch processing of forage samples. The FibreBag system is an economically necessary evolution of the earlier FibreCap system. The purpose of this enquiry was to determine if the FibreBag is a suitable replacement for the FibreCap. The FibreBag method produced very similar results to the FibreCap system of analy...

  20. Reliability of fibre Bragg gratings in polymer optical fibre

    OpenAIRE

    Dobb, H.; Carroll, K.; Kalli, K.; Komodromos, M.; Themistos, C.; Peng, G.D.; Argyros, A.; Large, M.C.J.; van Eijkelenborg, M.A.; Arresy, M.; Kukureka, S.

    2006-01-01

    In this paper we report on investigations of some of the factors that have a bearing on the reliability and repeatability of polymer fibre Bragg gratings. The main issues discussed are the fibre preform composition, the fibre drawing conditions and the thermal history of the fibre grating.

  1. 78 FR 8202 - Meeting of the Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy...

    Science.gov (United States)

    2013-02-05

    ... Hydraulic Phenomena and Materials, Metallurgy and Reactor Fuels; Notice of Meeting The Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy and Reactor Fuels will hold a meeting on...

  2. The Metallurgy of some indian swords

    Directory of Open Access Journals (Sweden)

    Williams, Alan

    2007-12-01

    Full Text Available The metallurgy of Indian swords shows many differences from that of European swords. The distinction between "Damascus Steel" (or wootz and crucible steel is explained. Ten broken blades from the Armoury of the Nizams of Hyderabad were made available for microscopic examination. Six of these seem to been made from crucible steels, and are of notably high quality. By contrast, a group of six randomly collected from Private Collections in England were also examined. Only one of these was made of crucible steel, and three of the others were of very mediocre quality. This perhaps represents the quality of blades available to the average Indian soldier.

    La metalurgia de las espadas indias presenta notables diferencias en comparación con la de las europeas. Se explica la distinción entre el ‘acero de Damasco’ (o wootz y el acero de crisol. Se ha realizado un análisis microscópico de un conjunto de diez hojas rotas de espada depositadas en la Armería de los Nizams de Hyderabad. Seis de ellas parecen haber sido realizadas a partir de acero de crisol, y son de elevada calidad. En contraste, se examinó también un grupo de seis espadas de colecciones privadas en Inglaterra. Sólo una de ellas estaba fabricada con acero de crisol, y tres de las otras eran de calidad muy mediocre. Esto representa quizá la calidad de las hojas de espada al alcance del soldado medio indio.

  3. POLARISATION PRESERVING OPTICAL FIBRE

    DEFF Research Database (Denmark)

    2000-01-01

    A micro-structured optical fibre having a cladding comprising a number of elements having a non-circular cross-section. Each element has at least one part extending outside a circle having the same cross-sectional area as the element. These extending parts are directed in the same direction....... This cladding structure provides polarisation preserving properties to the optical fibre. Optical fibres using this technology may have claddings with elements placed non-periodically as well as in a two-dimensional periodic lattice - such as cladding providing Photonic Band Gap (PBG) effects....

  4. Biennial activity report of Metallurgy Programme - 1985 and 1986

    International Nuclear Information System (INIS)

    Mallika, C.; Sreenivasan, P.R.; Muraleedharan, P.; Shyamsunder, M.T.; Kuppuswami, P.; Sampath, N.; Bhaduri, A.K.; Sreedharan, O.M.

    1988-01-01

    The biennial activity report of the Metallurgy Programme of the Indira Gandhi Centre for Atomic Research covers the period of the years 1985 and 1986. Along with NDT, welding metallurgy, low cycle fatigue, creep and creep fatigue interactions, structure-property correlations, thermodynamics and corrosion metallurgy of alloy steels with respect to their compatibility with aqueous and liquid sodium environments continue to be the major thrust areas of the Programme. Some of the basic research contributions of the Programme are: the observation of uniform and homogeneous distribution of voids in cyclically deformed 304 SS, the role of grain boundaries and precipitation in dynamic strain ageing of 316 SS and the determination of the activities of component metals in 316 and 304 SS by metastable EMF method. (author)

  5. Introduction to powder metallurgy processes for titanium manufacturing

    International Nuclear Information System (INIS)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-01-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  6. Summarizing of new techniques in uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Wang Delin; Zhang Fei; Su Yanru; Zeng Yijun; Meng Jin

    2010-01-01

    According to character of national resources and uranium mining and metallurgical science and technology members research achievements, new techniques in ten scientific research area of in-situ leaching, heap leaching, multi-metal comprehensive recovery, bio-metallurgy etc. for 10 years is introduced in this paper. The level of innovation ability is shown by technical index, resources recovery and reduction capital cost etc. datum. The application bound of natural uranium resource is enlarged and production ability of national uranium is increased. It is put forward renovation and development ideas for uranium mining and metallurgy. (authors)

  7. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  8. DETECTORS: scintillating fibres

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    In the continual search for improved detection techniques, new materials are continually proving profitable. A good example is scintillating plastic fibres - tiny transparent threads sometimes finer than a human hair which transmit light. The narrowness and flexibility of these fibres was a major breakthrough for endoscopy - non-invasive techniques for viewing the otherwise inaccessible in surgery or machine inspection. In a more sophisticated form, these fibres find ready application in communications technology, where the goal is to transmit information rather than electrical power, replacing conventional and unwieldy current-carrying wire conductors. In particle physics, fibres have long been used to take the tiny scintillations produced when high energy particles hit fluorescent materials and 'conduct' them to photosensitive detectors some distance away

  9. Fibre illumination system

    DEFF Research Database (Denmark)

    2012-01-01

    the proximal end of the collection optics into the first end of the input fibre, each collector element having a principal axis for the collection of light defining an optical axis of the collector element. The optical axes of the collector elements are arranged in a radially outward pointing multi......Source: EP2426402A The invention relates to a fibre illumination module and system for the collection and delivery of daylight for illumination purposes. The fibre illumination module comprises a plurality of collector elements, each collector element comprising an input fibre having a first end...... and a second end, and a collection optics, the collection optics being configured to receive light incident on a distal end of the collection optics, to transfer at least partially the incident light to a proximal end of the collection optics, and to couple at least partially the transferred light from...

  10. Optical fibre microwire sensors

    OpenAIRE

    Brambilla, G.; Belal, Mohammad; Jung, Y.; Song, Z.; Xu, F.; Newson, T.P.; Richardson, D.J.

    2011-01-01

    This paper reviews sensing applications of optical fibre microwires and nanowires. In addition to the usual benefits of sensors based on optical fibres, these sensors are extremely compact and have fast response speeds. In this review sensors will be grouped in three categories according to their morphology: linear sensors, resonant sensors and tip sensors. While linear and resonant sensors mainly exploit the fraction of power propagating outside the microwire physical boundary, tip sensors t...

  11. Fibre Concrete 2017

    Science.gov (United States)

    2017-09-01

    9th international conference on fibre reinforced concretes (FRC), textile reinforced concretes (TRC) and ultra-high performance concretes (UHPC) Preface The Fibre Concrete Conference series is held biennially to provide a platform to share knowledge on fibre reinforced concretes, textile concretes and ultra-high performance concretes regarding material properties and behaviour, technology procedures, topics of long-term behaviour, creep, durability; sustainable aspects of concrete including utilisation of waste materials in concrete production and recycling of concrete. The tradition of Fibre Concrete Conferences started in eighties of the last century. Nowadays the conference is organized by the Department of Concrete and Masonry Structures of the Czech Technical University in Prague, Faculty of Civil Engineering. The 9th International Conference Fibre Concrete 2017 had 109 participants from 27 countries all over the world. 55 papers were presented including keynote lectures of Professor Bažant, Professor Bartoš and Dr. Broukalová. The conference program covered wide range of topics from scientific research to practical applications. The presented contributions related to performance and behaviour of cement based composites, their long-term behaviour and durability, sustainable aspects, advanced analyses of structures from these composites and successful applications. This conference was organized also to honour Professor Zděnek P. Bažant on the occasion of his jubilee and to appreciate his merits and discoveries in the field of fibre reinforced composites, structural mechanics and engineering.

  12. The effect of powder metallurgy process parameters on mechanical ...

    African Journals Online (AJOL)

    The ever-increasing development of applying the iron pieces made by powder metallurgy in car industries and other usages depends on making pieces with high density and consequently acceptable physical and mechanical properties. Regarding the effect of decrease in the powder bits' size on improvement of the ...

  13. Chemical and Metallurgy Research (CMR) Sample Tracking System Design Document

    International Nuclear Information System (INIS)

    Bargelski, C. J.; Berrett, D. E.

    1998-01-01

    The purpose of this document is to describe the system architecture of the Chemical and Metallurgy Research (CMR) Sample Tracking System at Los Alamos National Laboratory. During the course of the document observations are made concerning the objectives, constraints and limitations, technical approaches, and the technical deliverables

  14. Damage on 316LN stainless steel transformed by powder metallurgy

    International Nuclear Information System (INIS)

    Couturier, R.; Burlet, H.

    1998-01-01

    This study deals with the 316 LN stainless steel elaboration by powder metallurgy. This method allows the realization of structures in austenitic steel less affected by the thermal aging than the cast austenitic-ferritic components. The components are performed by the method of HIP (Hot Isostatic Pressing). Mechanical tests are provided to control mechanical properties

  15. Iron Metallurgy: Technical Terminology Bulletin. Terminotech, Vol. 2, No. 7.

    Science.gov (United States)

    General Electric Co. of Canada, Ltd., Montreal, Quebec.

    This issue of a bulletin of technological terminology is devoted to iron metallurgy. Various aspects of iron production are described in both French and English. An English-French dictionary of terms comprises the bulk of the document. Explanatory illustrations are appended. (JB)

  16. [Hygienic evaluation of risk factors on powder metallurgy production].

    Science.gov (United States)

    2011-01-01

    Complex hygienic, clinical, sociologic and epidemiologic studies revealed reliable relationship between work conditions and arterial hypertension, locomotory system disorders, monocytosis in powder metallurgy production workers. Findings are more probable cardiovascular and respiratory diseases, digestive tract diseases due to influence of lifestyle factors.

  17. Microstructurally sensitive crack nucleation around inclusions in powder metallurgy nickel-based superalloys

    International Nuclear Information System (INIS)

    Jiang, J.; Yang, J.; Zhang, T.; Zou, J.; Wang, Y.; Dunne, F.P.E.; Britton, T.B.

    2016-01-01

    Nickel-based superalloys are used in high strength, high-value applications, such as gas turbine discs in aero engines. In these applications the integrity of the disc is critical and therefore understanding crack initiation mechanisms is of high importance. With an increasing trend towards powder metallurgy routes for discs, sometimes unwanted non-metallic inclusions are introduced during manufacture. These inclusions vary in size from ∼10 μm to 200 μm which is comparable to the grain size of the nickel-based superalloys. Cracks often initiate near these inclusions, and the precise size, shape, location and path of these cracks are microstructurally sensitive. In this study, we focus on crack initiation at the microstructural length scale using a controlled three-point bend test, with the inclusion deliberately located within the tensile fibre of the beam. Electron backscatter diffraction (EBSD) is combined with high spatial resolution digital image correlation (HR-DIC) to explore full field plastic strain distributions, together with finite element modelling, to understand the micro-crack nucleation mechanisms. This full field information and controlled sample geometry enable us to systematically test crack nucleation criteria. We find that a combined stored energy and dislocation density provide promising results. These findings potentially facilitate more reliable and accurate lifing prediction tools to be developed and applied to engineering components. - Highlights: • High resolution digital image correlation. • High resolution electron backscatter diffraction. • Crack nucleation. • Non-metallic inclusion.

  18. Glass ceramic fibres

    International Nuclear Information System (INIS)

    Blaschek, O.; Paulitsch, P.

    1983-01-01

    As the correlation between mineralogical phase and chemical composition influences the type of application at different high temperatures, we studied the mineralogical phases of nine crystal glass fibres of the temperature ranges 1 150 degrees Celsius (Type 1), 1 400 degrees Celsius (Type 2) and 1 500 degrees Celsius (Type 3) at various high temperatures. The methods used in the study were microscopy, X-ray diffraction, transmission electron microscopy and differential thermal analysis. The investigations showed that mullite forms in glassy fibres of the system Al 2 O 3 . SiO 2 from 850 degrees Celsius to 990 degrees Celsius as 2/1 mullite; 3/2 mullite appeared above 990 degrees Celsius besides the crystallization of cristobalite. Fibres with 95 per cent Al 2 O 3 include the phases delta-Al 2 O 3 and alpha- Al 2 O 3 and mullite. Delta- Al 2 O 3 is stable up to 1 100 degrees Celsius. Alpha-Al 2 O 3 and mullite are only stable phases at 1 400 degrees Celsius. These different crystal phases influence the quality of the technical fibre according to the stability field of glass and crystals. This study has determined that it is possible to identify different fibres from different productions by their mineralogical compositions and to relate them to the high temperature application

  19. Differences in mean fibre diameter and fibre diameter variance in ...

    African Journals Online (AJOL)

    sampled at five different body locations (Figure 1) at an age of 15 months. Samples were analysed by the Wool Testing. Bureaux, using an Optical Fibre Diameter Analyser which measured 4000 individual fibres in each sample. Apart from the mean, the variance of fibre diameter within samples was available. The statistical ...

  20. Multibeam Fibre Laser Cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    -laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single......The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre...

  1. Polarisation effects in fibre lasers

    OpenAIRE

    Lin, J.T.; Morkel, P.R.; Reekie, L.; Payne, D.N.

    1987-01-01

    Two orthogonal polarisation eigenmodes have been observed in a single-mode fibre laser. Experimental investigation shows good agreement with theoretical analysis. Both Nd3+ and Er3+-doped single-polarisation single-mode fibre lasers have been demonstrated

  2. Modelling of photonic crystal fibres

    DEFF Research Database (Denmark)

    Knudsen, Erik

    2003-01-01

    , as well as a honeycomb bandgap fibre and the first analysis of semi-periodic layered air-hole fibres. Using the modelling framework established as a basis, we provide an analysis of microbend loss, by regarding displacement of a fibre core as a stationary stochastic process, inducing mismatch between......In the presenta ph.d. work a theoretical study of aspects of modelling photonic crystal fibres was carried out. Photonic crystal fibres form a class of optical waveguides where guidance is no longer provided by a difference in refractive index between core and cladding. Instead, guidance...... is provided by an arrangement of air-holes running along the length of the fibre. Depending on the geometry of the fibre, the guiding mechanism may be either arising from the formation of a photonic bandgap in the cladding structure (photonic bandgap fibre), or by an effect resembling total internal...

  3. Current status of natural fibres

    CSIR Research Space (South Africa)

    Anandjiwala, RD

    2006-12-01

    Full Text Available Natural fibres and their products were prevalent since the early civilization of our society. Since then, the utilization and economic impact of natural fibre cultivation and down stream processing and products have been well established all over...

  4. Mineral fibres and health

    International Nuclear Information System (INIS)

    Hoskins, J.A.

    2001-01-01

    The use of inorganic fibrous materials is a comparatively new phenomenon and was uncommon before the Industrial Revolution. Humans evolved in a comparatively fibre-free environment and consequently never fully developed the defence mechanisms needed to deal with the consequences of inhaling fibres. However, the urban environment now has an airborne fibre concentration of around 1 f.l -1 , which is a tenfold increase on the natural background. Any sample of ambient air collected indoors or outdoors will probably contain some mineral fibres, but there is little evidence that these pose any risk to human health. They come from asbestos used in brakes, glass and mineral wools used as insulation and fire proofing of buildings, gypsum from plaster and a variety of types from many sources. Few of these have the potential to do any harm. Asbestos is the only fibre of note but urban levels are insignificant compared to occupational exposures. When the health of cohorts occupationally exposed to the several types of asbestos is studied the problem can be put into perspective. Studies of workers in the chrysotile industry exposed to much higher dust levels than in a factory today show no excess lung cancer or mesothelioma. By comparison those living near crocidolite mines, let alone working in them, may develop asbestos-related disease. As always, dose is the critical factor. Chrysotile is cleared from the lungs very efficiently, only the amphiboles are well retained. The only real health problem comes from the earlier use of asbestos products that may now be old, friable and damaged and made from amphibole or mixed fibre. If though, these are still in good condition, they do not pose a health problem. Asbestos-related diseases are very rare in those not occupationally exposed. Where they exist exposure has nearly always been to crocidolite. (author)

  5. Concrete workability and fibre content

    OpenAIRE

    Vikan, Hedda

    2007-01-01

    Research report Parameters influencing the workability of fibre concrete and maximum fibre content are given in this state of the art report along with the range of fibre types available on today’s market. The study reveales that new placing techniques and production methods are crucial in order to increase fibre content and concrete strength. Achieving the same mechanical properties as traditionally reinforced concrete will probably also demand changes of the matrix. Finally, reco...

  6. Single-mode optical fibres

    CERN Document Server

    Cancellieri, G

    1991-01-01

    This book describes signal propagation in single-mode optical fibres for telecommunication applications. Such description is based on the analysis of field propagation, considering waveguide properties and also some of the particular characteristics of the material fibre. The book covers such recent advances as, coherent transmissions; optical amplification; MIR fibres; polarization maintaining; polarization diversity and photon counting.

  7. Natural fibres-based polymers

    Indian Academy of Sciences (India)

    Natural fibres-based polymers: Part I—Mechanical analysis of Pine needles reinforced biocomposites. Vijay Kumar Thakur A S ... Keeping in view the various advantages of natural fibres, in current series of green composites a study on natural fibre reinforced polymer composites has been made. This paper presents the ...

  8. Powder Metallurgy characteristics and application: state of the art

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2005-01-01

    Powder metallurgy process (P/M) is a near-net or net-shape manufacturing process that combines the features of shape making technology of powder compaction with the development of final material and design properties (physical and mechanical) during subsequent densification or consolidation processes, e.g. sintering. It utilizes the metal powder or powders of metal alloys. In this paper, the major historical developments in P/M are reviewed and discussed. The main parameters involved in the process and their effects on the product characteristics are presented and discussed, which include: powders and methods of their production, particle size and shape, compressibility and additives, sintering temperature and time and finishing processes. The advantages and limitations of powder metallurgy are also presented and discussed. Finally, applications and future developments of the process are outlined and discussed. (author)

  9. Powder Metallurgy Fabrication of Molybdenum Accelerator Target Disks

    Energy Technology Data Exchange (ETDEWEB)

    Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans Jr., James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nunn, Stephen D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parten, Randy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-07-01

    Powder metallurgy approaches for the fabrication of accelerator target disks are being examined to support the development of Mo-99 production by NorthStar Medical Technologies, LLC. An advantage of powder metallurgy is that very little material is wasted and, at present, dense, quality parts are routinely produced from molybdenum powder. The proposed targets, however, are thin wafers, 29 mm in diameter with a thickness of 0.5 mm, with very stringent dimensional tolerances. Although tooling can be machined to very high tolerance levels, the operations of powder feed, pressing and sintering involve complicated mechanisms, each of which affects green density and shrinkage, and therefore the dimensions and shape of the final product. Combinations of powder morphology, lubricants and pressing technique have been explored to produce target disks with minimal variations in thickness and little or no distortion. In addition, sintering conditions that produce densities for optimum target dissolvability are being determined.

  10. Uranium 2000 : International symposium on the process metallurgy of uranium

    International Nuclear Information System (INIS)

    Ozberk, E.; Oliver, A.J.

    2000-01-01

    The International Symposium on the Process Metallurgy of Uranium has been organized as the thirtieth annual meeting of the Hydrometallurgy Section of the Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). This meeting is jointly organized with the Canadian Mineral Processors Division of CIM. The proceedings are a collection of papers from fifteen countries covering the latest research, development, industrial practices and regulatory issues in uranium processing, providing a concise description of the state of this industry. Topics include: uranium industry overview; current milling operations; in-situ uranium mines and processing plants; uranium recovery and further processing; uranium leaching; uranium operations effluent water treatment; tailings disposal, water treatment and decommissioning; mine decommissioning; and international regulations and decommissioning. (author)

  11. Microstructure and Aging of Powder-Metallurgy Al Alloys

    Science.gov (United States)

    Blackburn, L. B.

    1987-01-01

    Report describes experimental study of thermal responses and aging behaviors of three new aluminum alloys. Alloys produced from rapidly solidified powders and contain 3.20 to 5.15 percent copper, 0.24 to 1.73 percent magnesium, 0.08 to 0.92 percent iron, and smaller amounts of manganese, nickel, titanium, silicon, and zinc. Peak hardness achieved at lower aging temperatures than with standard ingot-metallurgy alloys. Alloys of interest for automobile, aircraft, and aerospace applications.

  12. Powder-metallurgy superalloy strengthened by a secondary gamma phase.

    Science.gov (United States)

    Kotval, P. S.

    1971-01-01

    Description of experiments in which prealloyed powders of superalloy compositions were consolidated by extrusion after the strengthening by precipitation of a body-centered tetragonal gamma secondary Ni3 Ta phase. Thin foil electron microscopy showed that the mechanical properties of the resultant powder-metallurgy product were correlated with its microstructure. The product exhibited high strength at 1200 F without loss of ductility, after thermomechanical treatment and aging.

  13. Mechanical and microstructural characterization of powder metallurgy CoCrNi medium entropy alloy

    Czech Academy of Sciences Publication Activity Database

    Moravčík, I.; Čížek, Jan; Kováčová, Z.; Nejezchlebová, J.; Kitzmantel, M.; Neubauer, E.; Kuběna, Ivo; Horník, Vít; Dlouhý, I.

    2017-01-01

    Roč. 701, July (2017), s. 370-380 ISSN 0921-5093 Institutional support: RVO:61389021 ; RVO:68081723 Keywords : tensile test * mechanical alloying * plasticity * mechanical characterization * powder metallurgy Subject RIV: JG - Metallurgy; JG - Metallurgy (UFM-A) OBOR OECD: Materials engineering ; Materials engineering (UFM-A) Impact factor: 3.094, year: 2016 https://www.sciencedirect.com/science/article/pii/S0921509317308535

  14. Optical Fibre Bundle

    CERN Multimedia

    These are sample fibre optic cables which are used for networking. Optical fibers are widely used in fiber-optic communications, where they permit transmission over longer distances and at higher bandwidths (data rates) than wire cables. Fibers are used instead of metal wires because signals travel along them with less loss and are also immune to electromagnetic interference. This is useful for somewhere like CERN where magnets with their highly powerful magnetic fields could pose a problem.

  15. Fibre-optical microendoscopy.

    Science.gov (United States)

    Gu, M; Bao, H; Kang, H

    2014-04-01

    Microendoscopy has been an essential tool in exploring micro/nano mechanisms in vivo due to high-quality imaging performance, compact size and flexible movement. The investigations into optical fibres, micro-scanners and miniature lens have boosted efficiencies of remote light delivery to sample site and signal collection. Given the light interaction with materials in the fluorescence imaging regime, this paper reviews two classes of compact microendoscopy based on a single fibre: linear optical microendoscopy and nonlinear optical microendoscopy. Due to the fact that fluorescence occurs only in the focal volume, nonlinear optical microendoscopy can provide stronger optical sectioning ability than linear optical microendoscopy, and is a good candidate for deep tissue imaging. Moreover, one-photon excited fluorescence microendoscopy as the linear optical microendoscopy suffers from severe photobleaching owing to the linear dependence of photobleaching rate on excitation laser power. On the contrary, nonlinear optical microendoscopy, including two-photon excited fluorescence microendoscopy and second harmonic generation microendoscopy, has the capability to minimize or avoid the photobleaching effect at a high excitation power and generate high image contrast. The combination of various nonlinear signals gained by the nonlinear optical microendoscopy provides a comprehensive insight into biophenomena in internal organs. Fibre-optical microendoscopy overcomes physical limitations of traditional microscopy and opens up a new path to achieve early cancer diagnosis and microsurgery in a minimally invasive and localized manner. © 2014 The Authors Journal of Microscopy © 2014 Royal Microscopical Society.

  16. Analysis of glass fibre sizing

    DEFF Research Database (Denmark)

    Petersen, Helga Nørgaard; Kusano, Yukihiro; Brøndsted, Povl

    2014-01-01

    surfaces are called sizing. The sizing influences the properties of the interface between fibres and a matrix, and subsequently affects mechanical properties of composites. In this work the sizing of commercially available glass fibres was analysed so as to study the composition and chemical structures......Glass fibre reinforced polymer composites are widely used for industrial and engineering applications which include construction, aerospace, automotive and wind energy industry. During the manufacturing glass fibres, they are surface-treated with an aqueous solution. This process and the treated....... Soxhlet extraction was used to extract components of the sizing from the glass fibres. The glass fibres, their extracts and coated glass plates were analysed by Thermo-Gravimetric Analysis combined with a mass spectrometer (TGA-MS), and Attenuated Total Reflectance Fourier Transform Infrared (ATR...

  17. Calcium binding by dietary fibre

    International Nuclear Information System (INIS)

    James, W.P.T.; Branch, W.J.; Southgate, D.A.T.

    1978-01-01

    Dietary fibre from plants low in phytate bound calcium in proportion to its uronic-acid content. This binding by the non-cellulosic fraction of fibre reduces the availability of calcium for small-intestinal absorption, but the colonic microbial digestion of uronic acids liberates the calcium. Thus the ability to maintain calcium balance on high-fibre diets may depend on the adaptive capacity on the colon for calcium. (author)

  18. Fibre constituents of some foods.

    Science.gov (United States)

    Rani, B; Kawatra, A

    1994-06-01

    Some plant foods viz. bottlegourd, carrot, cauliflower, cabbage, green bengalgram, pea, apple, plum, guava, karonda, blackgram husk and lentil husk were analysed for their dietary fibre components. The total dietary fibre contents of these foods varied from 14.68 to 78.21 percent on dry matter basis. As compared to fruits and vegetables, the husks had higher amount of total dietary fibre. Cellulose represented as the major fibre constituent in most of the foods whereas, husks were observed to be good sources of hemicellulose. All foods were low in pectin and lignin contents except guava.

  19. Advanced Fibre Based Energy Storage

    Science.gov (United States)

    Reid, Daniel Oliver

    New energy storage devices are required to enable future technologies. With the rise of wearable consumer and medical devices, a suitable flexible and wearable means of storing electrical energy is required. Fibre-based devices present a possible method of achieving this aim. Fibres are inherently more flexible than their bulk counterparts, and as such can be employed to form the electrodes of flexible batteries and capacitors. They also present a facile possibility for incorporation into many fabrics and clothes, further boosting their potential for use in wearable devices. Electrically conducting fibres were produced from a dispersion of carbon nanomaterials in a room temperature ionic liquid. Coagulation of this dispersion was achieved through manual injection into aqueous solutions of xanthan gum. The limitations of this method are highlighted by very low ultimate tensile strengths of these fibres, in the order of 3 MPa, with high variation within all of the fibres. Fibres were also produced via scrolling of bi-component films containing poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and poly(vinyl alcohol) (PVA). Chemical treatments were employed to impart water compatibility to these fibres, and their electrochemical, physical and electrical properties were analysed. Fibres were wet spun from two PEDOT:PSS sources, in several fibre diameters. The effect of chemical treatments on the fibres were investigated and compared. Short 5 min treatment times with dimethyl sulfoxide (DMSO) on 20 mum fibres produced from Clevios PH1000 were found to produce the best overall treatment. Up to a six-fold increase in electrical conductivity resulted, reaching 800 S cm-1, with up to 40 % increase in specific capacitance and no loss of mechanical strength (55 F g-1 and 150 MPa recorded). A wet spinning system to produce PEDOT:PSS fibres containing functionalised graphenes and carbon nanotubes, as well as birnessite nanotubes was subsequently developed

  20. A fibre optic displacement sensor

    OpenAIRE

    Sohlström, Hans; Holm, Ulf

    1982-01-01

    Fibre optics is beginning to find use for sensing purposes. Fibre optic sensors have many interesting features, e.g., their immunity to interference from electromagnetic fields. The paper briefly discusses different sensor principles. A displacement sensor using multimode, step index fibres is desccribed. Measurement data showing a resolution of 0.05 nm/sqrt(Hz) in a 150 µm linear range is given. In this sensor, the light coupling between two fibre ends varies with the position of a movable ...

  1. Development of Cu-Be bronzes through powder metallurgy

    International Nuclear Information System (INIS)

    Abbas, M.

    2012-01-01

    Copper and copper alloys are the major group of commercial alloy. One of the important copper bronzes is Copper beryllium. This is unique among all engineering alloys. Copper beryllium alloy possesses the highest strength in all the copper base alloys. Development of copper beryllium alloy with powder metallurgy is challenging problem due to toxicity of beryllium dust. Purpose of this project to find out parameters by which copper beryllium with all unique properties should obtained. For this purpose efforts are put on development of alternative to copper beryllium system like copper-tin and copper-aluminum by powder metallurgy route. Different time of milling with uniaxial pressure of about 200 MPa and different sintering temperature according to phase diagram of alloy, with different soaking time is tried. Problems may occur like decrease in density after sintering, breaking of samples by Rockwell A, B and C indenters arid by hammering. Cold iso-static pressing at 300 MPa and sintering at above 900 degree C is used to develop copper beryllium alloy. As quenched samples are heat treated at 260 degree C, 315 degree C and 370 degree C with different soaking time of 30, 90 and 180 minutes to find out optimum time and temperature parameters. . It is observed that at aging at 260 degree C for 180 minutes, aging at 315 degree C for 180 minutes and aging at 370 degree C for 30 minutes produce optimum result. By observing these pellets by SEM, precipitates appeared in peak-aged alloy and bigger precipitates in over-aged alloy. Copper beryllium alloy developed through powder metallurgy has better prospects than other copper bronzes. (author)

  2. Welding Metallurgy and Processing Issues for Joining of Power Sources

    Energy Technology Data Exchange (ETDEWEB)

    Lienert, Thomas J. [Los Alamos National Laboratory; Reardon, Patrick T. [Los Alamos National Laboratory

    2012-08-14

    Weldability issues with the pertinent alloys have been reviewed and preliminary results of our work on Haynes 25 have been presented. Further results on the mechanical properties and metallography on the EB welds are imminent. Hot-ductility experiments will commence within a few weeks. Aging studies on the effects of heat treatment using the Gleeble are also planned. MST-6 has extensive background in the welding metallurgy of the pertinent alloys. We also have considerable experience with the various welding processes to be used.

  3. Annual report of the Metallurgy Division - period ending December 1975

    International Nuclear Information System (INIS)

    1976-01-01

    The R and D activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay (India) during 1975 are described. Some of the R and D programmes of particular interest to nuclear technology are: (1) flowsheet development for the production of rare metals and alloys of nuclear use e.g. hafnium, beryllium, zirconium (2) metallurgical, irradiation hardening and corrosion studies on Zr and Zr-base alloys and (3) studies of nuclear ceramic materials such as UO2 and beryllia. (M.G.B.)

  4. Powder Metallurgy Reconditioning of Food and Processing Equipment Components

    Science.gov (United States)

    Nafikov, M. Z.; Aipov, R. S.; Konnov, A. Yu.

    2017-12-01

    A powder metallurgy method is developed to recondition the worn surfaces of food and processing equipment components. A combined additive is composed to minimize the powder losses in sintering. A technique is constructed to determine the powder consumption as a function of the required metallic coating thickness. A rapid method is developed to determine the porosity of the coating. The proposed technology is used to fabricate a wear-resistant defectless metallic coating with favorable residual stresses, and the adhesive strength of this coating is equal to the strength of the base metal.

  5. Properties of porous magnesium prepared by powder metallurgy.

    Science.gov (United States)

    Čapek, Jaroslav; Vojtěch, Dalibor

    2013-01-01

    Porous magnesium-based materials are biodegradable and promising for use in orthopaedic applications, but their applications are hampered by their difficult fabrication. This work reports the preparation of porous magnesium materials by a powder metallurgy technique using ammonium bicarbonate as spacer particles. The porosity of the materials depended on the amount of ammonium bicarbonate and was found to have strong negative effects on flexural strength and corrosion behaviour. However, the flexural strength of materials with porosities of up to 28 vol.% was higher than the flexural strength of non-metallic biomaterials and comparable with that of natural bone. Copyright © 2012 Elsevier B.V. All rights reserved.

  6. CURRENT STATE AND TENDENCIES OF DEVELOPMENT OF FERROUS METALLURGY IN THE EAEU COUNTRIES

    Directory of Open Access Journals (Sweden)

    N. P. Dragun

    2016-01-01

    Full Text Available The analysis of modern status and tendencies of development of ferrous metallurgy in the countries of the EAEU is described in the article. On the basis of the conducted analysis are revealed the identified systemic problems of metallurgy and the conclusions on possible ways of their solution using the potential of integration are given.

  7. Preliminary analysis about reducing production costs in uranium mining and metallurgy at Fuzhou uranium mine

    International Nuclear Information System (INIS)

    Wu Sanmao

    1999-01-01

    The production costs in uranium ming and metallurgy have been analyzed quantitatively term by term according to present production situation for The Uranium Mining and Metallurgy Corp, which is part of Fuzhou Uranium Mine. The principal factors influencing on the production costs and the main means reducing the production costs have been found

  8. Non-Linear Fibres for Widely Tunable Femtosecond Fibre Lasers

    DEFF Research Database (Denmark)

    Pedersen, Martin Erland Vestergaard

    of a fusion splicer and a gas-line burner, is applied to the few-moded fibres. An intermodal four-wave mixing process and a novel intermodal Cerenkov generation process are demonstrated experimentally in one of the two speciality few-moded fibres. The two intermodal processes are described theoretically...

  9. Creep properties of discontinuous fibre composites with partly creeping fibres

    International Nuclear Information System (INIS)

    Bilde-Soerensen, J.B.; Lilholt, H.

    1977-05-01

    In a previous report (RISO-M-1810) the creep properties of discontinuous fibre composites with non-creeping fibres were analyzed. In the present report this analysis is extended to include the case of discontinuous composites with partly creeping fibres. It is shown that the creep properties of the composite at a given strain rate, epsilonsub(c), depend on the creep properties of the matrix at a strain rate higher than epsilonsub(c), and on the creep properties of the fibres at epsilonsub(c). The composite creep law is presented in a form which permits a graphical determination of the composite creep curve. This can be constructed on the basis of the matrix and the fibre creep curves by vector operations in a log epsilon vs. log sigma diagram. The matrix contribution to the creep strength can be evaluated by a simple method. (author)

  10. Microstructured Optical Fibres

    DEFF Research Database (Denmark)

    1999-01-01

    complete PBGs, which reflects light incident from air or vacuum. Such structures may be used as cladding structures in optical fibres, where light is confined and thereby guided in a hollow core region. In addition, the present invention relates to designs for ultra low-loss PBG waveguiding structures......The present invention relates to a new class of optical waveguides, in which waveguiding along one or more core regions is obtained through the application of the Photonic Bandgap (PBG) effect. The invention further relates to optimised two-dimensional lattice structures capable of providing...

  11. Scintillating-fibre calorimetry

    International Nuclear Information System (INIS)

    Livan, M.; Vercesi, V.; Wigmans, R.

    1995-01-01

    In the past decade, calorimetry based on scintillating plastic fibres as active elements was developed from a conceptual idea to a mature detector technology, which is nowadays widely applied in particle physics experiments. This development and the performance characteristics of representative calorimeters, both for the detection of electromagnetic and hadronic showers, are reviewed. We also discuss new information on shower development processes in dense matter and its application to calorimetric principles that has emerged from some very thorough studies that were performed in the framework of this development. (orig.)

  12. Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

    DEFF Research Database (Denmark)

    Thygesen, Anders

    2006-01-01

    Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage...... obtained by steam explosion of hemp fibres prior defibrated with pectin degrading enzymes. The S2 layer in the fibre wall of the hemp fibres consisted of1-4 cellulose rich and lignin poor concentric layers constructed of ca. 100 nm thick lamellae. The microfibril angle showed values in the range 0......-10° for the main part of the S2-layer and 70-90° for the S1-layer. The microfibrils that are mainly parallelwith the fibre axis explain the high fibre stiffness, which in defibrated hemp fibres reached 94 GPa. The defibrated hemp fibres had higher fibre stiffness (88-94 GPa) than hemp yarn (60 GPa), which...

  13. Analysis of glass fibre sizing

    DEFF Research Database (Denmark)

    Petersen, Helga Nørgaard; Kusano, Yukihiro; Brøndsted, Povl

    2014-01-01

    . Soxhlet extraction was used to extract components of the sizing from the glass fibres. The glass fibres, their extracts and coated glass plates were analysed by Thermo-Gravimetric Analysis combined with a mass spectrometer (TGA-MS), and Attenuated Total Reflectance Fourier Transform Infrared (ATR...

  14. Design of DFB fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Povlsen, Jørn Hedegaard; Varming, Poul

    1998-01-01

    A numerical model for erbium distributed feedback (DFB) fibre lasers is presented. The model is used to optimise the location of a discrete phase-shift to obtain maximum output power. For DFB fibre lasers of up to 10cm in length it is shown that the influence of Kerr nonlinearity with respect...

  15. Design of DFB fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Povlsen, Jørn Hedegaard; Varming, Poul

    1998-01-01

    A numerical model for erbium distributed feedback (DFB) fibre lasers is presented. The model is used to optimise the location of a discrete phase-shift to obtain maximum output power. For DFB fibre lasers of up to 10cm in length it is shown that the influence of Kerr nonlinearity with respect to ...... to output power is negligible....

  16. The mysterious world of plutonium metallurgy: Past and future

    International Nuclear Information System (INIS)

    Hecker, S.S.; Hammel, E.F.

    1998-01-01

    The first atomic bomb detonated at the Trinity Site in New Mexico on July 16, 1945, used plutonium, a man-made element discovered < 5 yr earlier. The story of how Manhattan Project scientists and engineers tackled the mysteries of this element and fabricated it into the first atomic bomb is one of the most fascinating in the history of metallurgy and materials. The authors are currently trying to generate renewed interest in plutonium metallurgy because of the challenge posed by President Clinton, i.e., to keep the nuclear stockpile of weapons safe and reliable without nuclear testing. The stockpile stewardship challenge requires either a lifetime extension of the plutonium components or a remanufacture--neither of which can be verified by testing. In turn, this requires that one achieve a better fundamental understanding of plutonium. Of special interest is the effect of self-irradiation on the properties and on the long-term stability of plutonium and its alloys. Additional challenges arise from long-term concerns about disposing of plutonium and dealing with its environmental legacy. It is imperative to interest the next generation of students in these plutonium challenges

  17. Aligned flax fibre/polylactate composites

    DEFF Research Database (Denmark)

    Madsen, Bo; Lilholt, Hans; Thygesen, Anders

    2008-01-01

    are well predicted by the model. The back-calculated effective stiffness and failure stress of the flax fibres are in the ranges 56-60 GPa and 515-730 MPa, respectively. Finally, the model is used for parametric analysis and overall guidelines for the comparisons between tensile performance of flax fibre......The potential of biocomposites in engineering applications is demonstrated by using aligned flax fibre/polylactate composites as a materials model system. The failure stress of flax fibres is measured by tensile testing of single fibres and fibre bundles. For both fibre configurations, it is found...... that failure stress is decreased by increasing the tested fibre volume. Based on two types of flax fibre preforms: carded sliver and unidirectional non-crimp fabric, aligned flax fibre/polylactate composites were fabricated with variable fibre content. The volumetric composition and tensile properties...

  18. Bast fibre content, fibre yield and fibre quality of different linseed genotypes

    Directory of Open Access Journals (Sweden)

    H. SANKARI

    2008-12-01

    Full Text Available Linseed (Linum usitatissimum L. grown for seed does not compete well with flax in fibre yield, but as a by-product of seed production its stems could be used in non-woven products. With the aim of discovering suitable linseed genotypes to be cultivated for dual-purpose use in Finland, Finnish linseed cv. Helmi was compared with ten other linseed genotypes and one flax cultivar for stem yield, bast fibre content in stem, stem length and diameter and bast fibre yield. In addition, breaking tenacity and elongation at break of the fibres were determined. The experiments were carried out in 1996B1997 at the Agricultural Research Centre (MTT in Jokioinen, Finland (latitude 60o49'N. Bast fibre content in stem averaged 16.9% and breeding line Bor 18 had significantly higher bast fibre content than cv. Helmi. Bast fibre yield averaged 301 kg dry matter ha-1. Compared with cv. Helmi, breeding lines Bor 15 and Bor 18 and cvs. Flanders and Gold Merchant produced significantly higher fibre yield. The median for breaking tenacity varied among the genotypes between 41 and 67 cN/tex and the median for elongation at break between 3.5 and 6.8%. Finnish breeding line Bor 18 is recommended for cultivation as dual-purpose linseed in Finland. ;

  19. Dispersion properties of photonic crystal fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Dridi, Kim

    1998-01-01

    Approximate dispersion and bending properties of all-silica two-dimensional photonic crystal fibres are characterised by the combination of an effective-index model and classical analysis tools for optical fibres. We believe for the first time to have predicted the dispersion properties of photonic...... crystal fibres. The results strongly indicate that these fibres have potential applications as dispersion managing components...

  20. Use of fibre wastes from production of acetate fibres

    Energy Technology Data Exchange (ETDEWEB)

    Askarov, M.I.; Tashpulatova, A.B.

    1995-07-01

    The rational use of production wastes is an important part of the Fergana Chemical Fibre Plant in Russia. This recycling reduces the negative effect of the technological process on the environment, increases the economy of production, and produces additional consumer goods. Consumer goods began to be produced at the plant in 1978 with processing of amide-acetate textured fibres into yarn for hand knitting. The need to increase the volumes and expand the variety of goods for the market predetermined an important increase in production of this product. Production of consumer goods has increased since 1990, and both fibre wastes and untreated low-grade fibres and filaments have been used as the starting material. Technological processes for processing wastes and low-grade figured, textured polyamide-acetate fibres into knitting yarn, haberdashery cord, and finishing tape and fringe were created and introduced in subsequent years. The primary technological formulation for production of these materials is well known and is used in light industry. However, production of each type of product in the plant was preceded by research related to selection of the optimum linear density of the filaments used, composition of blends, and the structure of figured fibres, as well as the concrete technological parameters and operating regimes of the equipment to produce articles of the required quality. Development and testing of new decorative textiles are continuing. Low grade and nonstandard acetate semifinished fibre from spinning machines and low grade, bulk dyed acetate fibres have been selected as the raw material for fabrication of these articles.

  1. Fibre Bragg grating and no-core fibre sensors

    CERN Document Server

    Daud, Suzairi

    2018-01-01

    This book focuses on the development and set-up of fibre Bragg grating (FBG) and no-core fibre (NCF) sensors. It discusses the properties of the sensors and modelling of the resulting devices, which include electronic, optoelectronic, photovoltaic, and spintronic devices. In addition to providing detailed explanations of the properties of FBG and NCF sensors, it features a wealth of instructive illustrations and tables, helping to visualize the respective devices’ functions.

  2. New alloying systems for ferrous powder metallurgy precision parts

    Directory of Open Access Journals (Sweden)

    Danninger H.

    2008-01-01

    Full Text Available Traditionally, the common alloy elements for sintered steels have been Cu and Ni. With increasing requirements towards mechanical properties, and also as a consequence of soaring prices especially for these two metals, other alloy elements have also become more and more attractive for sintered steels, which make the steels however more tricky to process through PM. Here, the chances and risks of using in particular Cr and Mn alloy steels are discussed, considering the different alloying techniques viable in powder metallurgy, and it is shown that there are specific requirements in particular for sintering process. The critical importance of chemical reactions between the metal and the atmosphere is described, and it is shown that not only O2 and H2O but also H2 and even N2 can critically affect sintering and microstructural homogenization.

  3. Stress analyses of pump gears produced by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Cetinel, Hakan [Celal Bayar Univ., Mechanical Engineering Dept. (Turkey); Yilmaz, Burak

    2013-06-01

    In this study, trochoidal type (gerotor) hydraulic pump gears were produced by powder metallurgy (P/M) technique. Several gears with different mechanical properties have been obtained by changing process variables. The tooth contact stresses were calculated analytically under particular operation conditions of the hydraulic pump. The 3D models have been obtained from real gears by using Capability Maturity Model (CMM, 3D scanning) operation and SOLIDWORKS software. Stress analyses were conducted on these 3D models by using ANSYS WORKBENCH software. It was found that the density increases by the increase of sintering duration and mechanical properties were positively affected by the increase of density. Maximum deformation takes place in the region of the outer gear where failure generally occurs with the minimum cross-section area.

  4. An application of powder metallurgy for the LHC

    CERN Document Server

    Sgobba, Stefano

    2004-01-01

    The cold mass of the 1232 superconducting dipole magnets of LHC, operating at 1.9 K, is enclosed by a shrinking cylinder and two end covers at its extremities. The covers are structural components that must retain high strength and toughness at cryogenic temperature. They are manufactured by Metso Oy /FI in AISI 316 LN steel by Powder Metallurgy (PM) and Hot Isostatic Pressing. PM represents an attractive near net shaping technique for these components of complex geometry for which dimension tolerances, dimensional stability, weldability are key issues for magnet fabrication, and mechanical properties, ductility and leak tightness have to be guaranteed during operation. The material of the covers and its welds have been fully characterized and mechanically tested down to 4.2 K at CERN. The fine grained structure, the absence of residual stresses, the full isotropy of mechanical properties associated to the low level of Prior Particle Boundaries oxides result in superior mechanical properties and high ductilit...

  5. N18, powder metallurgy superalloy for disks: Development and applications

    Energy Technology Data Exchange (ETDEWEB)

    Guedou, J.Y.; Lautridou, J.C.; Honnorat, Y. (SNECMA, Evry (France). Materials and Processes Dept.)

    1993-08-01

    The preliminary industrial development of a powder metallurgy (PM) superalloy, designated N18, for disk applications has been completed. This alloy exhibits good overall mechanical properties after appropriate processing of the material. These properties have been measured on both isothermally forged and extruded billets, as well as on specimens cut from actual parts. The temperature capability of the alloy is about 700 C for long-term applications and approximately 750 C for short-term use because of microstructural instability. Further improvements in creep and crack propagation properties, without significant reduction in tensile strength, are possible through appropriate thermomechanical processing, which results in a large controlled grain size. Spin pit tests on subscale disks have confirmed that the N18 alloy has a higher resistance than PM Astrology and is therefore an excellent alloy for modern turbine disk applications.

  6. Powder metallurgy: Solid and liquid phase sintering of copper

    Science.gov (United States)

    Sheldon, Rex; Weiser, Martin W.

    1993-01-01

    Basic powder metallurgy (P/M) principles and techniques are presented in this laboratory experiment. A copper based system is used since it is relatively easy to work with and is commercially important. In addition to standard solid state sintering, small quantities of low melting metals such as tin, zinc, lead, and aluminum can be added to demonstrate liquid phase sintering and alloy formation. The Taguchi Method of experimental design was used to study the effect of particle size, pressing force, sintering temperature, and sintering time. These parameters can be easily changed to incorporate liquid phase sintering effects and some guidelines for such substitutions are presented. The experiment is typically carried out over a period of three weeks.

  7. Advanced powder metallurgy aluminum alloys via rapid solidification technology

    Science.gov (United States)

    Ray, R.

    1984-01-01

    Aluminum alloys containing 10 to 11.5 wt. pct. of iron and 1.5 to 3 wt. pct. of chromium using the technique of rapid solidification powder metallurgy were studied. Alloys were prepared as thin ribbons (.002 inch thick) rapidly solidified at uniform rate of 10(6) C/second by the melt spinning process. The melt spun ribbons were pulverized into powders (-60 to 400 mesh) by a rotating hammer mill. The powders were consolidated by hot extrusion at a high reduction ratio of 50:1. The powder extrusion temperature was varied to determine the range of desirable processing conditions necessary to yield useful properties. Powders and consolidated alloys were characterized by SEM and optical metallography. The consolidated alloys were evaluated for (1) thermal stability, (2) tensile properties in the range, room temperature to 450 F, and (3) notch toughness in the range, room temperature to 450 F.

  8. The Chemical Composition of Grape Fibre

    OpenAIRE

    Jolana Karovičová; Zlatica Kohajdová; Lucia Minarovičová; Veronika Kuchtová

    2015-01-01

    Dietary fibres from cereals are much more used than dietary fibres from fruits; however, dietary fibres from fruits have better quality. In recent years, for economic and environmental reasons, there has been a growing pressure to recover and exploit food wastes. Grape fibre is used to fortify baked goods, because the fibre can lower blood sugar, cut cholesterol and may even prevent colon cancer. Grape pomace is a functional ingredient in bakery goods to increase total phenolic content and di...

  9. Modeling of photonic Crystal Fibres

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Broeng, Jes; Barkou, Stig Eigil

    1999-01-01

    Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated.......Diferent theoretical models for analysis of photonic crystal fibres are reviewed and compaired. The methods span from simple scalar approaches to full-vectorial models using different mode-field decompositions. The specific advantages of the methods are evaluated....

  10. Advanced fibre based energy storage.

    OpenAIRE

    Reid, Daniel

    2017-01-01

    New energy storage devices are required to enable future technologies. With the rise of wearable consumer and medical devices, a suitable flexible and wearable means of storing electrical energy is required. Fibre-based devices present a possible method of achieving this aim. Fibres are inherently more flexible than their bulk counterparts, and as such can be employed to form the electrodes of flexible batteries and capacitors. They also present a facile possibility for incorporation into man...

  11. The Chemical Composition of Grape Fibre

    Directory of Open Access Journals (Sweden)

    Jolana Karovičová

    2015-05-01

    Full Text Available Dietary fibres from cereals are much more used than dietary fibres from fruits; however, dietary fibres from fruits have better quality. In recent years, for economic and environmental reasons, there has been a growing pressure to recover and exploit food wastes. Grape fibre is used to fortify baked goods, because the fibre can lower blood sugar, cut cholesterol and may even prevent colon cancer. Grape pomace is a functional ingredient in bakery goods to increase total phenolic content and dietary fibre in nourishment. The aim of this study was to determine the chemical composition of commercial fibres, obtained from different Grape sources concerning their chemical properties such as moisture, ash, fat, protein, total dietary fibre. The chemical composition of Grape fibre is known to vary depending on the Grape cultivar, growth climates, and processing conditions. The obliged characteristics of the fibre product are: total dietary fibre content above 50%, moisture lower than 9%, low content of lipids, a low energy value and neutral flavour and taste. Grape pomace represents a rich source of various high-value products such as ethanol, tartrates and malates, citric acid, Grape seed oil, hydrocolloids and dietary fibre. Used commercial Grape fibres have as a main characteristic, the high content of total dietary fibre. Amount of total dietary fibre depends on the variety of Grapes. Total dietary fibre content (TDF in our samples of Grape fibre varied from 56.8% to 83.6%. There were also determined low contents of moisture (below 9%. In the samples of Grape fibre were determined higher amount of protein (8.6 - 10.8%, mineral (1.3 - 3.8% and fat (2.8 - 8.6%. This fact opens the possibility of using both initial by-products as ingredients in the food industry, due to the effects associated with the high total dietary fibre content.

  12. Connectorization of fibre Bragg grating sensors recorded in microstructured polymer optical fibre

    DEFF Research Database (Denmark)

    Abang, A.; Saez-Rodriguez, D.; Nielsen, Kristian

    2013-01-01

    We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate).......We describe te production and characterization of FC/PC connectorised fibre Bragg grating sensors in polymer fibre. Sensors were recorded in few-moded and single mode microstructured fibre composed of poly (methyl methacrylate)....

  13. Uranium mining and metallurgy library information service under the network environment

    International Nuclear Information System (INIS)

    Tang Lilei

    2012-01-01

    This paper analyzes the effect of the network environment on the uranium mining and metallurgy of the information service. Introduces some measures such as strengthening professional characteristic literature resources construction, changing the service mode, building up information navigation, deepening service, meet the individual needs of users, raising librarian's quality, promoting the co-construction and sharing of library information resources, and puts forward the development idea of uranium mining and metallurgy library information service under the network environment. (author)

  14. Production of uranium in Navoi Mining and Metallurgy Combinat, Uzbekistan

    International Nuclear Information System (INIS)

    Kuchersky, N.; Tolstov, E.A.; Mazurkevich, A.P.; Inozemzev, S.B.

    2001-01-01

    Full text: Under the conditions of constantly increasing level of development of the nuclear power, it is inevitable that the uranium stockpiles accumulated to 1985 will soon be depleted. This consideration underlies the development concept of uranium production in the Navoi Mining and Metallurgy Combinat, Uzbekistan. Because this product has become a source of hard currency revenues for the Republic, there will be a significant increase in the processed ore and output of uranium oxide within the next few years. Uranium production in the Navoi Mining and Metallurgy Combinat represents a full-cycle operations ranging from geological survey through hydrometallurgical processing resulting in the output of uranium concentrate in the form of uranium protoxide-oxide (U 3 O 8 ). The NMMC uranium operations include the Hydrometallurgical Plant and three facilities accomplishing ISL mining facilities. A successful start on the development of the Uchkuduk deposit by ISL method in the 1960s gave rise to scientific and production approach for development of other uranium deposits of the infiltration bedded (sandstone) type. Uranium recovery by ISL has become a separate mining branch within the 30-year period of its history and the contribution of this branch in uranium production has steadily grown. Since 1995 all uranium produced by Navoi Mining and Metallurgy Combinat is attributed to ISL. During this evolution period of the ISL method, a whole range of systematic scientific research and practical works were carried out covering improvement of process flowsheets, equipment, operational methods and techniques for particular mining conditions at those specific sites. In co-operation with design and scientific research institutions, a significant number of scientific researches, test works, design and engineering projects were achieved in order to create optimal conditions for ISL mining and further processing of pregnant solutions by sorption as well as to appropriately equip

  15. Development and application of characteristic database for uranium mining and metallurgy in the library of Beijing Research Institute of Chemical Engineering and Metallurgy

    International Nuclear Information System (INIS)

    Gao Renxi

    2012-01-01

    Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM) is a multi disciplinary comprehensive research institute engaged in uranium mining, engineering design and related material researches. After 53 years of researches and development, BRICEM has accumulated a plenty of valuable data and resources. By analyzing the actual conditions of BRICEM's technological database, this thesis aims to propose the idea of building a characteristic database for uranium mining and metallurgy. It gives an in-depth analysis on content design, development status and problems of database development, in order to come up with solutions to these problems, as well as suggestions on the future development plans of the characteristic database. (author)

  16. Carbon nanotubes for ultrafast fibre lasers

    Directory of Open Access Journals (Sweden)

    Chernysheva Maria

    2016-06-01

    Full Text Available Carbon nanotubes (CNTs possess both remarkable optical properties and high potential for integration in various photonic devices. We overview, here, recent progress in CNT applications in fibre optics putting particular emphasis on fibre lasers. We discuss fabrication and characterisation of different CNTs, development of CNT-based saturable absorbers (CNT-SA, their integration and operation in fibre laser cavities putting emphasis on state-of-the-art fibre lasers, mode locked using CNT-SA. We discuss new design concepts of high-performance ultrafast operation fibre lasers covering ytterbium (Yb, bismuth (Bi, erbium (Er, thulium (Tm and holmium (Ho-doped fibre lasers.

  17. Practical Hydrogen Loading of Air Silica Fibres

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Jensen, Jesper Bevensee; Jensen, Jesper Bo Damm

    2005-01-01

    A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown.......A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown....

  18. Production of titanium alloys for medical implants by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Henriques, V.A.R. [Dept. de Engenharia de Materiais, Faculdade de Engenharia Quimica de Lorena, Lorena SP (Brazil); Silva, C.R.M. da [Div. de Materiais, CTA-IAE-AMR, Sao Jose dos Campos SP (Brazil)

    2001-07-01

    Titanium alloys are expected to be much more widely used for implant materials in the medical and dental fields because of their superior biocompatibility, corrosion resistance and specific strength compared with other metallic implant materials. Vanadium free alloys like Ti-6Al-7Nb and Ti-5Al-2,5Fe have been recently developed for biomedical use. More recently vanadium and aluminum free alloys composed of non-toxic elements like Nb, Ta, Zr and so on with lower modulus have been started to be developed. The {beta} type alloys like Ti-15Mo are now the main target for medical materials. A blended elemental titanium powder metallurgy process has been developed to offer low cost products. The process employs hydride-dehydride (HDH) powders and near-net shape techniques. In this work, the influence of the processing parameters and chemical composition of the elementary powders on the final microstructure was investigated. The alloys were characterized by means of scanning electron microscopy, X-ray diffraction, Vickers microhardness measurements, chemical analysis and density. The results indicate that the samples presented high densification, homogeneous chemical composition and coherent microstructures. The process parameters were defined aiming to reduce the interstitial pick-up (O, N) and to avoid the grain growth. (orig.)

  19. The traces of roman metallurgy in Eastern Serbia

    Directory of Open Access Journals (Sweden)

    Petković Sofija

    2009-01-01

    Full Text Available The archaeological traces of the Roman mining and metallurgy in eastern Serbia are rather frequent but insufficiently studied and published. Three mining-metallurgical regions abounding in gold, silver, copper, iron and lead could be distinguished there: 1. the upper course of the Pek river, metalla Pincensia, 2. the area between Bor, Zlot, Crna Reka and Rgotina and 3. the area in the river basin of Beli Timok, two latter ones had been organized as territoria metallorum. The archeometallurgical sites confirmed by investigations are: Kraku lu Jordan at the confluence of the Brodica river and the Pek river, Rudna Glava, Tilva Roš in Bor, Gamzigrad - Romuliana, Rgotina near Zaječar and Timacum Minus in the village Ravna near Knjaževac. Roman mining-metallurgical activities in eastern Serbia flourished from the end of the 3rd century, were interrupted by the invasion of Huns in AD 441. and restored in the time of emperors Anastasius and Justin I, in the end of the 5th - beginning of the 6th centuries. The Roman mining-metallurgical centers functioned in the 6th century until the Slav invasion in the beginning of the 7th century.

  20. Wear mechanisms in powder metallurgy high speed steels matrix composites

    International Nuclear Information System (INIS)

    Gordo, E.; Martinez, M. A.; Torralba, J. M.; Jimenez, J. A.

    2001-01-01

    The development of metal matrix composites has a major interest for automotive and cutting tools industries since they possess better mechanical properties and wear resistance than corresponding base materials. One of the manufacturing methods for these materials includes processing by powder metallurgy techniques. in this case, blending of both, base material and reinforcement powders constitute the most important process in order to achieve a homogeneous distribution of second phase particles. in the present work, composite materials of M3/2 tool steel reinforced with 2.5,5 and 8 vol% of niobium carbide have been prepared. In order to ensure a homogeneous mix, powders of both materials were mixed by dry high-energy mechanical milling at 200 r.p.m. for 40 h. After a recovering annealing, two routes for consolidate were followed die pressing and vacuum sintering, and hot isostatic pressing (HIP). Pin-on-disc tests were carried out to evaluate wear behaviour in all the materials. Results show that ceramic particles additions improve wear resistance of base material. (Author) 9 refs

  1. TRADITIONAL METALLURGY, NANOTECHNOLOGIES AND STRUCTURAL MATERIALS: A SORBY AWARD LECTURE

    Energy Technology Data Exchange (ETDEWEB)

    Louthan, M

    2007-07-17

    Traditional metallurgical processes are among the many ''old fashion'' practices that use nanoparticles to control the behavior of materials. Many of these practices were developed long before microscopy could resolve nanoscale features, yet the practitioners learned to manipulate and control microstructural elements that they could neither see nor identify. Furthermore, these early practitioners used that control to modify microstructures and develop desired material properties. Centuries old colored glass, ancient high strength steels and medieval organ pipes derived many of their desirable features through control of nanoparticles in their microstructures. Henry Sorby was among the first to recognize that the properties of rocks, minerals, metals and organic materials were controlled by microstructure. However, Mr. Sorby was accused of the folly of trying to study mountains with a microscope. Although he could not resolve nanoscale microstructural features, Mr. Sorby's observations revolutionized the study of materials. The importance of nanoscale microstructural elements should be emphasized, however, because the present foundation for structural materials was built by manipulating those features. That foundation currently supports several multibillion dollar industries but is not generally considered when the nanomaterials revolution is discussed. This lecture demonstrates that using nanotechnologies to control the behavior of metallic materials is almost as old as the practice of metallurgy and that many of the emergent nanomaterials technologists are walking along pathways previously paved by traditional metallurgists.

  2. [Possible health effects associated with Pre-Columbian metallurgy].

    Science.gov (United States)

    Idrovo, Alvaro Javier

    2005-09-01

    In the Old World, several researchers have indicated that adverse health effects were associated with exposure to arsenic, and that this influenced a change in the use of copper-arsenic alloys to others less toxic. This hypothesis was evaluated for three Pre-Columbian metallurgy traditions: Central Andes, Intermediate Area, and West Mexico. The metal artifacts from the Central Andes showed arsenic concentrations similar to those in the Old World (0.5%-1.0%). In the Intermediate Area the values were smallest; however, in West Mexico the arsenic content was very high (7%-25%). In Central Andes arsenical bronze was used initially, but copper-tin alloys when introduced were preferred and distributed throughout the Inca Empire. Osteological and artistic evidences of foot amputations among Moche individuals from Central Andes support the presence of "black foot disease" (a condition associated with arsenic poisoning) among Pre-Columbian populations. In conclusion, the adverse effects of arsenic have been observed in the New World, and that these effects promoted a change toward the use of less toxic alloys.

  3. Drop on a bent fibre.

    Science.gov (United States)

    Pan, Zhao; Weyer, Floriane; Pitt, William G; Vandewalle, Nicolas; Truscott, Tadd T

    2018-03-15

    Inspired by the huge droplets attached on cypress tree leaf tips after rain, we find that a bent fibre can hold significantly more water in the corner than a horizontally placed fibre (typically up to three times or more). The maximum volume of the liquid that can be trapped is remarkably affected by the bending angle of the fibre and surface tension of the liquid. We experimentally find the optimal included angle (∼36°) that holds the most water. Analytical and semi-empirical models are developed to explain these counter-intuitive experimental observations and predict the optimal angle. The data and models could be useful for designing microfluidic and fog harvesting devices.

  4. Carbon fibre material for tomorrow

    International Nuclear Information System (INIS)

    Kartini Noorsal; Mohd Ariff Baharom

    2010-01-01

    As science and technology continue to cross boundaries of known practices, materials and manufacturing techniques and into the frontiers of new materials, environment and applications, the opportunities for research in materials in general will inevitably increase. The unique properties of carbon fibre which combines low weight and high stiffness, makes it in ever greater demand as substitutes for traditional materials. This is due to the rising costs of raw materials and energy and the necessity to reduce carbon dioxide emission. The carbon fibres produced are particularly of high standard in terms of quality and processing characteristics especially when it is designed in structural components in the aerospace and defence industries. This results in a well structured organisation in producing the fibre starting from its raw material to the final composite products. In achieving this effort, research and communication of the progress takes a fundamental role. (author)

  5. LHCb Upgrade: Scintillating Fibre Tracker

    International Nuclear Information System (INIS)

    Tobin, Mark

    2016-01-01

    The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less read-out system. All front-end electronics will be replaced and several sub-detectors must be redesigned to cope with higher occupancy. The current tracking detectors downstream of the LHCb dipole magnet will be replaced by the Scintillating Fibre (SciFi) Tracker. The SciFi Tracker will use scintillating fibres read out by Silicon Photomultipliers (SiPMs). State-of-the-art multi-channel SiPM arrays are being developed to read out the fibres and a custom ASIC will be used to digitise the signals from the SiPMs. The evolution of the design since the Technical Design Report in 2014 and the latest R & D results are presented.

  6. Fibre Optics In Coal Mining

    Science.gov (United States)

    Cooper, Paul

    1984-08-01

    Coal mines have a number of unique problems which affect the use of fibre optic technology. These include a potentially explosive atmosphere due to the evolution of methane from coal, and a dirty environment with no cleaning facilities readily available. Equipment being developed by MRDE to allow the exploitation of optical fibres underground includes: A hybrid electrical/fibre optic connector for the flexible power trailing cable of the coal-face shearer; An Intrinsically Safe (IS) pulsed laser transmitter using Frequency Shift Key (FSK) data modulation; An IS Avalanche Photo Diode Receiver suitable for pulsed & continuous wave optical signals; A mine shaft and roadway cable/ connector system incorporating low loss butt-splices and preterminated demountable connectors.

  7. Indexation Rules for Metallurgy in PASCAL. Original Title: Regles d'Indexation de la Metallurgie'--Technical Note Issued by Informascience--January 1980. Translated by Marie Wallin.

    Science.gov (United States)

    Royal Inst. of Tech., Stockholm (Sweden). Library.

    The indexing rules presented are designed for use with a new French-German database on metallurgy being developed under an agreement by CNRS (Centre National de la Recherche Scientifique, Paris) and BAM (Bundesanstalt fur Materialprufung, Berlin). The new database, which will feature multilingual titles and index terms (French-German-English-) and…

  8. Development of hemp fibre - PP nonwoven composites

    CSIR Research Space (South Africa)

    Hargitai, H

    2006-01-01

    Full Text Available Nonwoven mats from hemp and polypropylene fibres in various proportions were produced and hot pressed to make composite material. The effect of hemp fibre content and anisotropy in nonwoven mats resulting from the carding technology were examined...

  9. Hollow Core Photonic Crystal Fibre Comprising a Fibre Grating in the Cladding and its Applications

    DEFF Research Database (Denmark)

    2010-01-01

    An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction.......An optical fibre is provided having a fibre cladding around a longitudinally extending optical propagation core. The cladding has a reflection region of a varying refractive index in the longitudinal direction....

  10. The Influence of Fibre Content on the Performance of Steel Fibre ...

    African Journals Online (AJOL)

    Steel fibres are commonly used in the refractory industry to reinforce high temperature concretes. Little information is available on the effect of fibre content on refractory performance and in particular resistance to thermal shock. This study has examined the influence of fibre content of stainless steel melt extract fibres on the ...

  11. Fibre reinforced concrete in flexure and single fibre pull-out test: a correlation

    Science.gov (United States)

    Manca, M.; Ciancio, D.; Dight, P.

    2017-09-01

    The aim of the present work is to assess whether a single fibre pull-out test can be related to the behaviour of multiple fibres in fibre reinforced concrete under bending condition. A simple model based on the stress block theory is described and compared with experimental results on three point bending tests with aligned fibres.

  12. Methodology for characterisation of glass fibre composite architecture

    DEFF Research Database (Denmark)

    Hansen, Jens Zangenberg; Larsen, J.B.; Østergaard, R.C.

    2012-01-01

    of the fibres. The information is used for different analyses to investigate and characterise the fibre architecture. As an example, the methodology is applied to glass fibre reinforced composites with varying fibre contents. The different fibre volume fractions (FVFs) affect the number of contact points per...... fibre architecture and composite properties....

  13. Photonic crystal fibres and effective index approaches

    DEFF Research Database (Denmark)

    Riishede, Jesper; Libori, Stig E. Barkou; Bjarklev, Anders Overgaard

    2001-01-01

    Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres.......Photonic crystal fibres are investigated with an effective index approach. The effective index of both core and cladding is found to be wavelength dependent. Accurate modelling must respect the rich topology of these fibres....

  14. Local fibred right adjoints are polynomial

    DEFF Research Database (Denmark)

    Kock, Anders; Kock, Joachim

    2013-01-01

    For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense......For any locally cartesian closed category E, we prove that a local fibred right adjoint between slices of E is given by a polynomial. The slices in question are taken in a well known fibred sense...

  15. Fibre Optic Communication Key Devices

    CERN Document Server

    Grote, Norbert

    2012-01-01

    The book gives an in-depth description of the key devices of current and next generation fibre optic communication networks. In particular, the book covers devices such as semiconductor lasers, optical amplifiers, modulators, wavelength filters, and detectors but the relevant properties of optical fibres as well. The presentations include the physical principles underlying the various devices, the technologies used for the realization of the different devices, typical performance characteristics and limitations, and development trends towards more advanced components are also illustrated. Thus the scope of the book spans relevant principles, state-of-the-art implementations, the status of current research and expected future components.

  16. Carbon Fibres from Kraft Lignin

    OpenAIRE

    Norberg, Ida

    2012-01-01

    Kraft lignin has a high potential for use in more valuable applications than its current use as fuel in pulp mills and integrated pulp and paper mills. The possibility of using kraft lignin, a green material with a carbon content of more than 60 %, for the manufacturing of carbon fibres was investigated in this thesis. The strong and lightweight carbon fibre material has many potential application areas, e.g. in cars; the main obstacle limiting its demand is the high production cost, with the...

  17. Active textiles with Janus fibres

    Science.gov (United States)

    Zakharov, A. P.; Pismen, L. M.

    We describe reshaping of active textiles actuated by bending of Janus fibres comprising both active and passive components. A great variety of shapes, determined by minimising the overall energy of the fabric, can be produced by varying bending directions determined by the orientation of Janus fibres. Under certain conditions, alternative equilibrium states, one absolutely stable and the other metastable coexist, and their relative energy may flip its sign as system parameters, such as the extension upon actuation, change. A snap-through reshaping in a specially structured textile reproduces the Venus flytrap effect.

  18. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available animal hair fibres L Hunter, CSIR and Nelson Mandela Metropolitan University (NMMU), South Africa Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury...

  19. Continuous jute fibre reinforced laminated paper composite

    Indian Academy of Sciences (India)

    Plastic bags create a serious environmental problem. The proposed jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate may help to combat the war against this pollutant to certain extent. The paper laminate, without reinforcement fibre, exhibited a few fold superiority in tensile ...

  20. Stress concentrations in an impregnated fibre bundle with random fibre packing

    OpenAIRE

    Swolfs, Y.; Gorbatikh, L.; Romanov, V.; Orlova, S.; Lomov, S. V.; Verpoest, I.

    2013-01-01

    The stress redistribution after a single fibre break is a fundamental issue in longitudinal strength models for unidirectional composites. Current models assume hexagonal or square fibre packings. In the present work, random fibre packings were modelled using 3D finite element analysis and compared to ordered fibre packings. Significant differences in the stress redistribution are found. Compared to square and hexagonal packings, random fibre packings result in smaller stress concentration fa...

  1. Mechanical processing of bast fibres: The occurrence of damage and its effect on fibre structure

    DEFF Research Database (Denmark)

    Hänninen, Tuomas; Thygesen, Anders; Mehmood, Shahid

    2012-01-01

    Currently, separation processes used for natural fibres for composite reinforcing textiles cause a significant amount of damage to the fibres. Microscopic analysis showed that industrially processed flax (Linum usitassimium L.) fibres contained significantly more defects than green or retted ones...... to heterogeneous reactivity. Analogous findings were observed in hemp (Cannabis sativa L.) fibre damaged in the laboratory under controlled conditions, emphasising the need to develop extraction and separation processes that minimise mechanical damage to the fibres....

  2. [Atmospheric emission of PCDD/Fs from secondary aluminum metallurgy industry in the southwest area, China].

    Science.gov (United States)

    Lu, Yi; Zhang, Xiao-Ling; Guo, Zhi-Shun; Jian, Chuan; Zhu, Ming-Ji; Deng, Li; Sun, Jing; Zhang, Qin

    2014-01-01

    Five secondary aluminum metallurgy enterprises in the southwest area of China were measured for emissions of PCDD/Fs. The results indicated that the emission levels of PCDD/Fs (as TEQ) were 0.015-0.16 ng x m(-3), and the average was 0.093 ng x m(-3) from secondary aluminum metallurgy enterprises. Emission factors of PCDD/Fs (as TEQ) from the five secondary aluminum metallurgy enterprises varied between 0.041 and 4.68 microg x t(-1) aluminum, and the average was 2.01 microg x t(-1) aluminum; among them, PCDD/Fs emission factors from the crucible smelting furnace was the highest. Congener distribution of PCDD/F in stack gas from the five secondary aluminum metallurgies was very different from each other. Moreover, the R(PCDF/PCDD) was the lowest in the enterprise which was installed only with bag filters; the R(PCDF/PCDD) were 3.8-12.6 (the average, 7.7) in the others which were installed with water scrubbers. The results above indicated that the mechanism of PCDD/Fs formation was related to the types of exhaust gas treatment device. The results of this study can provide technical support for the formulation of PCDD/Fs emission standards and the best available techniques in the secondary aluminum metallurgy industry.

  3. A method for estimating the fibre length in fibre-PLA composites.

    Science.gov (United States)

    Chinga-Carrasco, G; Solheim, O; Lenes, M; Larsen, A

    2013-04-01

    Wood pulp fibres are an important component of environmentally sound and renewable fibre-reinforced composite materials. The high aspect ratio of pulp fibres is an essential property with respect to the mechanical properties a given composite material can achieve. The length of pulp fibres is affected by composite processing operations. This thus emphasizes the importance of assessing the pulp fibre length and how this may be affected by a given process for manufacturing composites. In this work a new method for measuring the length distribution of fibres and fibre fragments has been developed. The method is based on; (i) dissolving the composites, (ii) preparing the fibres for image acquisition and (iii) image analysis of the resulting fibre structures. The image analysis part is relatively simple to implement and is based on images acquired with a desktop scanner and a new ImageJ plugin. The quantification of fibre length has demonstrated the fibre shortening effect because of an extrusion process and subsequent injection moulding. Fibres with original lengths of >1 mm where shortened to fibre fragments with length of <200 μm. The shortening seems to be affected by the number of times the fibres have passed through the extruder, the amount of chain extender and the fraction of fibres in the polymer matrix. © 2013 The Authors Journal of Microscopy © 2013 Royal Microscopical Society.

  4. Nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch

    is potentially the case for microstructured polymer optical fibres (mPOFs). Another advantage is that polymer materials have a higher biocompatibility than silica, meaning that it is easier to bond certain types of biosensor materials to a polymer surface than to silica. As with silica PCFs, it is difficult...

  5. Cool application for Optical Fibres

    CERN Multimedia

    2001-01-01

    In a new first for CERN, optical fibres have been put on test to measure very low temperatures. If these tests prove successful, this new technology could lead to important cost-saving changes in the way the temperatures of superconducting magnets are measured. There was excitement in the air last March when the team led by Walter Scandale and Luc Thévenaz tested very low temperature measurement using optical fibres. This spring in CERN's Cryogenics lab an idea was put to the test as a new kind of low-temperature thermometry using optical fibres was tested down to 2 Kelvin (around 300 degrees below room temperature), and the first results are looking good. Optical fibres are well known for their ability to carry large amounts of data around the world, but it is less well known that they can be used for measuring temperatures. The intuition that they might be able to measure very low temperatures - such as those of the LHC magnets - came to the attention of CERN's Walter Scandale at the Optical Fi...

  6. Flow diagnostics using fibre optics

    Indian Academy of Sciences (India)

    high enthalpy, high speed flows and in combustion chambers, rocket exhausts etc. 3. Aerodynamic load measurements at hypersonic speeds using internally mounted fibre-optic balance system. 3.1 The IISc hypersonic wind tunnel. The IISc hypersonic wind tunnel is of the pressure-vacuum type with an open jet test section.

  7. Moisture sorption in naturally coloured cotton fibres

    Science.gov (United States)

    Ceylan, Ö.; De Clerck, K.

    2017-10-01

    Increasing environmental concerns have stimulated an interest in naturally coloured cottons. As many commercial and technical performance aspects of cotton fibres are influenced by their response towards atmospheric humidity, an in-depth research on moisture sorption behaviour of these fibres using dynamic vapour sorption is carried out. Significant differences were observed in sorption capacity and hysteresis behaviour of brown and green cotton fibres. These differences are mainly attributed to the variations in maturity and crystallinity index of the fibres. This study provides valuable insights into the moisture sorption behaviour of naturally coloured cotton fibres.

  8. Laser–fibre vibrometry at 1550 nm

    International Nuclear Information System (INIS)

    Waz, A T; Kaczmarek, P R; Abramski, K M

    2009-01-01

    This paper presents new solutions for laser vibrometry, which are based on fibre vibrometry in the third telecommunication window. The scattered laser beam from a vibrating object is guided by a fibre collimator and coherently detected through heterodyning it with an acousto-optical frequency-shifted reference beam. The concept of measuring vibration parameters from many points of the vibrating object has been inspired by wavelength division multiplexing (WDM) in fibre telecommunications. The N-independent WDM separated 15XX nm fibre-coupled laser diodes (used for optical fibre telecommunications) form a system of sources for multipoint vibration measurement according to the rule 'one wavelength–one point'

  9. Fibre optic power meter calibration uncertainties

    CSIR Research Space (South Africa)

    Nel, M

    2010-06-01

    Full Text Available The method to empirically quantify the effect that flexing (movement) of the fibre has on the output power was determined by connecting an optical fibre to a power meter head and performing controlled movements of the head (displacements and rotations..., and with their optical axes roughly parallel to one another to reduce the effect of fibre flexing when interchanging from one detector head to another. Excessive flexing and moving of the fibre can cause differences in the radiant power emerging from the fibre...

  10. Fibre optic cable in the nuclear industry

    International Nuclear Information System (INIS)

    Roberts, Berwyn

    1987-01-01

    The uses of optical fibre cables to transmit light signals include medical applications and telecommunications. In the nuclear industry the applications include process control and monitoring, conventional datacoms, security fencing and sensors. Time division multiplexing is described and currently available fibre optic multipexers are listed and explained. Single and multimode fibres are mentioned. Fibre optics are also used in cryogenics, to monitor the integrity of the storage vessels for cryogenic liquids. The uses of fibre optics at Hartlepool, Heysham I and Torness are mentioned in particular. (UK)

  11. Superplasticity in powder metallurgy aluminum alloys and composites

    International Nuclear Information System (INIS)

    Mishra, R.S.; Bieler, T.R.; Mukherjee, A.K.

    1995-01-01

    Superplasticity in powder metallurgy Al alloys and composites has been reviewed through a detailed analysis. The stress-strain curves can be put into 4 categories: classical well-behaved type, continuous strain hardening type, continuous strain softening type and complex type. The origin of these different types of is discussed. The microstructural features of the processed material and the role of strain have been reviewed. The role of increasing misorientation of low angle boundaries to high angle boundaries by lattice dislocation absorption is examined. Threshold stresses have been determined and analyzed. The parametric dependencies for superplastic flow in modified conventional aluminum alloys, mechanically alloyed alloys and Al alloy matrix composites is determined to elucidate the superplastic mechanism at high strain rates. The role of incipient melting has been analyzed. A stress exponent of 2, an activation energy equal to that for grain boundary diffusion and a grain size dependence of 2 generally describes superplastic flow in modified conventional Al alloys and mechanically alloyed alloys. The present results agree well with the predictions of grain boundary sliding models. This suggests that the mechanism of high strain rate superplasticity in the above-mentioned alloys is similar to conventional superplasticity. The shift of optimum superplastic strain rates to higher values is a consequence of microstructural refinement. The parametric dependencies for superplasticity in aluminum alloy matrix composites, however, is different. A true activation energy of superplasticity in aluminum alloy matrix composites, however, is different. A true activation energy of 313 kJ/mol best describes the composites having SiC reinforcements. The role of shape of the reinforcement (particle or whisker) and processing history is addressed. The analysis suggests that the mechanism for superplasticity in composites is interface diffusion controlled grain boundary sliding

  12. Corrosion inhibition of powder metallurgy Mg by fluoride treatments.

    Science.gov (United States)

    Pereda, M D; Alonso, C; Burgos-Asperilla, L; del Valle, J A; Ruano, O A; Perez, P; Fernández Lorenzo de Mele, M A

    2010-05-01

    Pure Mg has been proposed as a potential degradable biomaterial to avoid both the disadvantages of non-degradable internal fixation implants and the use of alloying elements that may be toxic. However, it shows excessively high corrosion rate and insufficient yield strength. The effects of reinforcing Mg by a powder metallurgy (PM) route and the application of biocompatible corrosion inhibitors (immersion in 0.1 and 1M KF solution treatments, 0.1M FST and 1M FST, respectively) were analyzed in order to improve Mg mechanical and corrosion resistance, respectively. Open circuit potential measurements, polarization techniques (PT), scanning electrochemical microscopy (SECM) and electrochemical impedance spectroscopy (EIS) were performed to evaluate its corrosion behavior. SECM showed that the local current of attacked areas decreased during the F(-) treatments. The corrosion inhibitory action of 0.1M FST and 1M FST in phosphate buffered solution was assessed by PT and EIS. Under the experimental conditions assayed, 0.1M FST revealed better performance. X-ray photoelectron spectroscopy, energy dispersive X-ray and X-ray diffraction analyses of Mg(PM) with 0.1M FST showed the presence of KMgF(3) crystals on the surface while a MgF(2) film was detected for 1M FST. After fluoride inhibition treatments, promising results were observed for Mg(PM) as degradable metallic biomaterial due to its higher yield strength and lower initial corrosion rate than untreated Mg, as well as a progressive loss of the protective characteristics of the F(-)-containing film which ensures the gradual degradation process. Copyright (c) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  13. Elastic fibres in health and disease.

    Science.gov (United States)

    Baldwin, Andrew K; Simpson, Andreja; Steer, Ruth; Cain, Stuart A; Kielty, Cay M

    2013-08-20

    Elastic fibres are insoluble components of the extracellular matrix of dynamic connective tissues such as skin, arteries, lungs and ligaments. They are laid down during development, and comprise a cross-linked elastin core within a template of fibrillin-based microfibrils. Their function is to endow tissues with the property of elastic recoil, and they also regulate the bioavailability of transforming growth factor β. Severe heritable elastic fibre diseases are caused by mutations in elastic fibre components; for example, mutations in elastin cause supravalvular aortic stenosis and autosomal dominant cutis laxa, mutations in fibrillin-1 cause Marfan syndrome and Weill-Marchesani syndrome, and mutations in fibulins-4 and -5 cause autosomal recessive cutis laxa. Acquired elastic fibre defects include dermal elastosis, whereas inflammatory damage to fibres contributes to pathologies such as pulmonary emphysema and vascular disease. This review outlines the latest understanding of the composition and assembly of elastic fibres, and describes elastic fibre diseases and current therapeutic approaches.

  14. Plant fibre composites - porosity and volumetric interaction

    DEFF Research Database (Denmark)

    Madsen, Bo; Thygesen, Anders; Lilholt, Hans

    2007-01-01

    the combination of a high fibre volume fraction, a low porosity and a high composite density is optimal. Experimental data from the literature on volumetric composition and density of four types of plant fibre composites are used to validate the model. It is demonstrated that the model provides a concept......Plant fibre composites contain typically a relative large amount of porosity, which considerably influences properties and performance of the composites. The large porosity must be integrated in the conversion of weight fractions into volume fractions of the fibre and matrix parts. A model...... is presented to predict the porosity as a function of the fibre weight fractions, and to calculate the related fibre and matrix volume fractions, as well as the density of the composite. The model predicts two cases of composite volumetric interaction separated by a transition fibre weight fraction, at which...

  15. Progress report of the Metallurgy Division for the period 1978-1980

    International Nuclear Information System (INIS)

    Sharma, B.D.; Mohan, Ashok; Bose, D.K.; Rao, C.N.; Chouthai, S.S.

    1980-01-01

    The research and development (R and D) work of the Metallurgy Division of the Bhabha Atomic Research Centre at Bombay for the period 1978-1980 is reported in the form of individual summaries under the headings: extractive metallurgy section, physical metallurgy section, corrosion and electrometallurgy section, ceramics section. Progress of work of beryllium pilot plant project, programme for R-5 utilisation for materials irradiation research project, development of rare, reactive and refractory metals, and development of ceramics materials for MHD programme is surveyed. Lists of publications, deputations, visits, conferences, colloquia are given. A chart at the end shows the various sections of the Division and personnel in each section. (M.G.B.)

  16. Introduction to powder metallurgy processes for titanium manufacturing; Introduccion al procesado pulvimetalurgico del titanio

    Energy Technology Data Exchange (ETDEWEB)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-07-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  17. 76 FR 64344 - Amended Record of Decision for the Nuclear Facility Portion of the Chemistry and Metallurgy...

    Science.gov (United States)

    2011-10-18

    ... the same sets of safety controls and key equipment. Further, as the SEIS analysis indicates, once... Nuclear Facility Portion of the Chemistry and Metallurgy Research Building Replacement Project at Los...) for the Nuclear Facility portion of the Chemistry and Metallurgy Research Building Replacement (CMRR...

  18. Modernization of the Ural Metallurgy during the Great Patriotic War (1941–1945

    Directory of Open Access Journals (Sweden)

    Vladimir V. Zaparii

    2013-09-01

    Full Text Available The article characterizes the Ural industry modernization in war footing, shows the significance of evacuation of enterprises from the Western areas of the country to the region, reveals their role in the formation of a new metallurgical center of modern metallurgy in terms of human resources and manufacture. Innovations in metallurgy, the role of human factor in solving industrial restructuring problem are examined. Forms and methods of science use for the industrial modernization are considered. Solving of human resources problem is shown. The author touches upon the problem of metallurgical sector management in wartime. The role of people’s heroism in this difficult period of Russian history is discussed.

  19. Metallurgy of high-silicon steel parts produced using Selective Laser Melting

    OpenAIRE

    Garibaldi, Michele; Ashcroft, Ian; Simonelli, Marco; Hague, Richard

    2016-01-01

    The metallurgy of high-silicon steel (6.9%wt.Si) processed using Selective Laser Melting (SLM) is presented for the first time in this study. High-silicon steel has great potential as a soft magnetic alloy, but its employment has been limited due to its poor workability. The effect of SLM-processing on the metallurgy of the alloy is investigated in this work using microscopy, X-Ray Diffraction (XRD) and Electron Backscatter Diffraction (EBSD). XRD analysis suggests that the SLM high-silicon s...

  20. [Analysis of changes in characteristics of arterial hypertension occupational risk in workers of nonferrous metallurgy].

    Science.gov (United States)

    Vlasova, E M; Shliapnikov, D M; Lebedeva, T M

    2015-01-01

    The article covers changes in occupational cardiovascular risk for workers of nonferrous,metallurgy. Findings are that exposure to noise up to 94 dB with length of service increases possible atherosclerosis and metabolic syndrome. With 5 years of service, risk of the predicted conditions increases by 40.5%. When occupational exposure lasts over 5 years, risk of arterial hypertension increases. A group of workers without exposure to occupational factors appeared to have no connection between length of service and metabolic syndrome and arterial hypertension. Risk evolution modelling proved that risk of functional disorders in nonferrous metallurgy workers becomes unacceptable after 5 years of service (cardiovascular disorders are critical).

  1. Fundamentals of fibre-reinforced soil engineering

    CERN Document Server

    Shukla, Sanjay Kumar

    2017-01-01

    This book is intended to serve as a one-stop reference on fibre-reinforced soils. Over the past 30-35 years, the engineering behaviour of randomly distributed/oriented fibre-reinforced soil, also called simply fibre-reinforced soil, has been investigated in detail by researchers and engineers worldwide. Waste fibres (plastic waste fibres, old tyre fibres, etc.) create disposal and environmental problems. Utilization of such fibres in construction can help resolve these concerns. Research studies and some field applications have shown that the fibres can be utilized in large quantities in geotechnical and civil engineering applications in a cost-effective and environmentally friendly manner. This book covers a complete description of fibres, their effects when included within a soil or other similar materials such as the fly ash, and their field applications. It gives a detailed view of fibre-reinforced soil engineering. The book will be useful to students, professional, and researchers alike, and can also ser...

  2. Fibre reinforced concrete exposed to elevated temperature

    Science.gov (United States)

    Novák, J.; Kohoutková, A.

    2017-09-01

    Although concrete when subject to fire performs very well, its behaviour and properties change dramatically under high temperature due to damaged microstructure and mesostructure. As fibre reinforced concrete (FRC) represents a complex material composed of various components with different response to high temperature, to determine its behaviour and mechanical properties in fire is a demanding task. The presented paper provides a summary of findings on the fire response of fibre FRC. Namely, the information on steel fibre reinforced concrete (SFRC), synthetic fibre reinforced concrete and hybrid (steel + synthetic) fibre reinforced concrete have been gathered from various contributions published up to date. The mechanical properties including the melting point and ignition point of fibres affect significantly the properties of concrete composites with addition of fibres. The combination of steel and synthetic fibres represents a promising alternative how to ensure good toughness of a concrete composite before heating and improve its residual mechanical behaviour and spalling resistance as well as the ductility after heating. While synthetic fibres increase concrete spalling resistance, steel fibres in a concrete mix leads to an improvement in both mechanical properties and resistance to heating effects.

  3. Metallurgy, environmental pollution and the decline of Etruscan civilisation.

    Science.gov (United States)

    Harrison, Adrian P; Cattani, Ilenia; Turfa, Jean M

    2010-01-01

    The Etruscans were justifiably famous in antiquity for their advanced metallurgy and for the rich mineral resources of their region (including La Tolfa, the Colline Metallifere, Mont'Amiata and Elba). We offer a new perspective on certain Iron Age and Archaic (ca. 1,000-480 BC: ) Etruscan industrial and habitation sites, and on the problem of heavy metal poisoning, still being investigated today, coincidentally in some of the same areas that originally saw Etruscan mines and workshops. This study investigates ancient sources, including literature and excavation reports, in the light of modern studies of heavy metal poisoning on human beings, plant and animal life. Furthermore, it is the first to use non-invasive Niton X-ray fluorescence analysis of samples of Etruscan (strictly ethnically Faliscan) hair (c. 350 BCE: ). The findings show the strong likelihood of heavy metal poisoning in areas of Etruscan metallurgical activity with the effects of this being responsible for or contributing to the abandonment of a number of these sites around the 6th century BC: . No thoroughly satisfactory explanation of this phenomenon has previously been offered. However, findings suggest that Faliscan women, represented by sample CG 2004-6-2, were not exposed to high levels of arsenic in life, which is not perhaps surprising for an urban aristocratic woman of the mid-4th century BC: . The reasons for the abandonment of several flourishing settlements are without doubt complex, and include political and social change. We suggest heavy metal contamination as an additional stimulus to the noted phenomenon of the peaceful abandonment, at the beginning, and at the end of the 6th century BC: , of sites in southern and northern Etruria such as Marsiliana d'Albegna (late 7th c.), Lago dell'Accesa, Acquarossa and Poggio Civitate-Murlo (late 6th c.). While the historical truth of the demise of Etruscan civilisation is much more complex, an interim set of related events, the desertion of

  4. Fibre optic communication key devices

    CERN Document Server

    Grote, Norbert

    2017-01-01

    The book gives an in-depth description of key devices of current and next generation fibre optic communication networks. Devices treated include semiconductor lasers, optical amplifiers, modulators, wavelength filters and other passives, detectors, all-optical switches, but relevant properties of optical fibres and network aspects are included as well. The presentations include the physical principles underlying the various devices, technologies used for their realization, typical performance characteristics and limitations, but development trends towards more advanced components are also illustrated. This new edition of a successful book was expanded and updated extensively. The new edition covers among others lasers for optical communication, optical switches, hybrid integration, monolithic integration and silicon photonics. The main focus is on Indium phosphide-based structures but silicon photonics is included as well. The book covers relevant principles, state-of-the-art implementations, status of curren...

  5. Flow diagnostics using fibre optics

    Indian Academy of Sciences (India)

    a finely machined calibration body as shown in figure 10. The entire loading setup was placed under water in a fish tank measuring 3 × 1·5 × 1·25 ft as shown in figure 11. Prede- termined loads were applied to the balance and the resulting calibration curves are shown in figure 12a & b. The fibre-optic processor was set at ...

  6. Standard Fibre Optic Ring LANs

    Science.gov (United States)

    Beale, N. C. L.

    1985-08-01

    The paper begins with a reminder of the particular need for standards in LANs. We then describe the requirements of High Integrity LANs. Current developments in LAN standards are then outlined. It is argued that the requirements of industrial LANs lead ideally to reconfiguring fibre optic rings, for which there are two major emerging standards. These two (IEEE 802.5 and ANSI FDDI) and the Cambridge Ring are discussed and compared. One implementation - the HILAN is discussed.

  7. Factors That Improve the Impact Responses of Ukam Plant Fibre ...

    African Journals Online (AJOL)

    Natural fibres around us have mechanical properties capable of making them compete effectively with synthetic fibres in the development of fibre reinforced composites. Synthetic fibres (such as glass fibres) and resins (such as polyester resin) have long been used in the development of structural components for car bodies, ...

  8. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...... of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish...

  9. Frost resistance of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1999-01-01

    of 0.4-1% by volume of fibres cannot replace air entrainment in order to secure a frost resistant concrete; the minimum amount of air needed to make the concrete frost resistant is not changed when adding fibres· the amount of air entrainment must be increased when fibres are added to establish......Frost resistance of fibre reinforced concrete with 2.5-4.2% air and 6-9% air (% by volume in fresh concrete) casted in the laboratory and in-situ is compared. Steel fibres with hooked ends (ZP, length 30 mm) and polypropylene fibres (PP, CS, length 12 mm) are applied. It is shown that· addition...

  10. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place

    1998-01-01

    Durability studies are carried out at BKM as part of the research project "Design Methods for Fibre Reinforced Concrete" (FRC) involving BKM, The Concrete Research Center at DTI, Building Technology at Aalborg University, Rambøll, 4K-Beton and Rasmussen & Schiøtz. Concrete beams with or without...... fibre reinforcement are exposed to a combination of mechanical and environmental load to indicate whether fibre reinforcement will improve the durability of cracked concrete structures. Secondly, it is the aim to identify important mechanisms for the effect of the fibre reinforcement on the durability......) and polypropylene fibres (PP) are used in the concrete beams as well as main reinforcement. Results of the durability tests on cracked FRC-beams are compared with results for uncracked FRC-beams and beams without fibres....

  11. Theorem of comparative sensitivity of fibre sensors

    Science.gov (United States)

    Belovolov, M. I.; Paramonov, V. M.; Belovolov, M. M.

    2017-12-01

    We report an analysis of sensitivity of fibre sensors of physical quantities based on different types of interferometers. We formulate and prove the following theorem: under the time-dependent external physical perturbations at nonzero frequencies (i.e., except the static and low-frequency ones) on the sensitive arms of an interferometer in the form of multiturn elements (coils), there exist such lengths L of the measuring arms of the fibre interferometers at which the sensitivity of sensors based on the Sagnac fibre interferometers can be comparable with the sensitivity of sensors based on Michelson, Mach - Zehnder, or Fabry - Perot fibre interferometers, as well as exceed it under similar other conditions (similar-type perturbations, similar arm lengths and single-mode fibre types). The consequences that follow from the theorem, important for practical implementation of arrays of fibre sensors for measurement purposes and the devices with stable metrological properties, are discussed.

  12. Uranium mining and metallurgy library science and technology literature retrieval of network

    International Nuclear Information System (INIS)

    Tang Lilei

    2014-01-01

    This paper introduces the network resources and characteristics retrieve service of Beijing research Institute of Chemical Engineering of Metallurgy library, Analyzes the problems often encountered in the literature retrieval in science and technology, And puts forward the solution, Puts forward the thinking and Suggestions of science and technology literature retrieval. (author)

  13. Solvent Extraction of Copper: An Extractive Metallurgy Exercise for Undergraduate Teaching Laboratories

    Science.gov (United States)

    Smellie, Iain A.; Forgan, Ross S.; Brodie, Claire; Gavine, Jack S.; Harris, Leanne; Houston, Daniel; Hoyland, Andrew D.; McCaughan, Rory P.; Miller, Andrew J.; Wilson, Liam; Woodhall, Fiona M.

    2016-01-01

    A multidisciplinary experiment for advanced undergraduate students has been developed in the context of extractive metallurgy. The experiment serves as a model of an important modern industrial process that combines aspects of organic/inorganic synthesis and analysis. Students are tasked to prepare a salicylaldoxime ligand and samples of the…

  14. Metallurgy department progress report for the period 1 January to 31 December 1981

    International Nuclear Information System (INIS)

    1982-07-01

    The activities of the Metallurgy Department at Risoe during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1981 is included. (author)

  15. Metallurgy department progress report for the period 1 January to 31 December 1982

    International Nuclear Information System (INIS)

    1983-07-01

    The activities of the Metallurgy Department at Risoe during 1982 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Deveopment, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1982 is included. (author)

  16. Powder metallurgy preparation of Al-Cu-Fe quasicrystals using mechanical alloying and Spark Plasma Sintering

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Kubatík, Tomáš František; Vystrčil, J.; Hendrych, R.; Kříž, J.; Mlynár, J.; Vojtěch, D.

    2014-01-01

    Roč. 52, September (2014), s. 131-137 ISSN 0966-9795 Institutional support: RVO:61389021 Keywords : Nanostructure intermetallics * Ternary alloys systems * Mechanical alloying and milling * Sintering * Diffraction Subject RIV: JG - Metallurgy Impact factor: 2.131, year: 2014 http://www.sciencedirect.com/science/article/pii/S0966979514001198#

  17. Recycling of wastes from uranium mining and metallurgy and recovery of useful resources in China

    International Nuclear Information System (INIS)

    Pan Yingjie; Xue Jianxin; Chen Zhongqiu

    2012-01-01

    Recycling of wastes from uranium mining and metallurgy in China and recovery of useful resources are summarized from the aspects such as recovery of uranium from mine water, reusing of waste water, decontaminating and recycling of radioactivity contaminated metal, backfill of gangues and tailings, and comprehensive recovery and utilization of associated uranium deposits. (authors)

  18. Practical application of solid phase spectrophotometry in analysis of materials and goods of mining and metallurgy

    International Nuclear Information System (INIS)

    Duan Qunzhang

    1999-01-01

    The author reviewed recent development and practical application of solid phase spectrophotometry in analysis of materials and goods of mining-metallurgy. Separation and preconcentration and conditions of coloring determination, sensitivity and range of detection, as well as interference of corresponding method are discussed

  19. Annual report of the Metallurgy Division [for the] period ending December 1977

    International Nuclear Information System (INIS)

    Elayaperumal, K.; Sridhar Rao, Ch.; Mukhopadhyay, P.; Rao, S.V.K.

    1979-01-01

    The research and development work carried out and the various programmes underway in the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the calendar year 1977 have been reported. The R and D work and programmes cover extraction metallurgy, physical metallurgy, alloy development, corrosion metallurgy and ceramics. Some of the major studies and programmes are: (1) development of processes for extraction of niobium, vanadium, hafnium and nickel, (2) preparation of niobium alloys, ferro-zirconium, ceramic grade zirconia, (3) electro-refining of zircaloy scrap, (4) preparation of anhydrous beryllium fluoride from Indian beryl, (5) preparation of beryllium alloys, (6) studies on phase transformation and deformation behaviour of zirconium and zirconium-oxygen alloys, (7) self-diffusion studies in dilute Zr-Fe and Zr-Cr alloys, (8) studies on corrosion and stress corrosion cracking of zirconium base alloys and (9) sintering studies on ZrO 2 -PuO 2 and BeO. (M.G.B.)

  20. Metallurgy Department progress report for the period 1 January to 31 December 1984

    International Nuclear Information System (INIS)

    1985-04-01

    The activities of the Metallurgy Department at Risoe during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1984 is included. (author)

  1. Powder Metallurgy Preparation of Co-Based Alloys for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Marek, I.; Novák, P.; Mlynár, J.; Vojtěch, D.; Kubatík, Tomáš František; Málek, J.

    2015-01-01

    Roč. 128, č. 4 (2015), s. 597-601 ISSN 0587-4246. [International Symposium on Physics of Materials (ISPMA) /13./. Prague, 31.08.2014-04.09.2014] Institutional support: RVO:61389021 Keywords : powder metallurgy * mechanical properties * biomedical applications Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 0.525, year: 2015

  2. Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

    Science.gov (United States)

    Harf, Fredric H.

    1989-01-01

    Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

  3. Ice-core evidence of earliest extensive copper metallurgy in the Andes 2700 years ago.

    Science.gov (United States)

    Eichler, A; Gramlich, G; Kellerhals, T; Tobler, L; Rehren, Th; Schwikowski, M

    2017-01-31

    The importance of metallurgy for social and economic development is indisputable. Although copper (Cu) was essential for the wealth of pre- and post-colonial societies in the Andes, the onset of extensive Cu metallurgy in South America is still debated. Comprehensive archaeological findings point to first sophisticated Cu metallurgy during the Moche culture ~200-800 AD, whereas peat-bog records from southern South America suggest earliest pollution potentially from Cu smelting as far back as ~2000 BC. Here we present a 6500-years Cu emission history for the Andean Altiplano, based on ice-core records from Illimani glacier in Bolivia, providing the first complete history of large-scale Cu smelting activities in South America. We find earliest anthropogenic Cu pollution during the Early Horizon period ~700-50 BC, and attribute the onset of intensified Cu smelting in South America to the activities of the central Andean Chiripa and Chavin cultures ~2700 years ago. This study provides for the first time substantial evidence for extensive Cu metallurgy already during these early cultures.

  4. A Guide for Planning Facilities for Occupational Preparation Programs in Metallurgy Technology. Interim Report. Research 28.

    Science.gov (United States)

    German, Carl, Jr.

    The major purpose of this guide is to elicit the information necessary for writing educational specifications for facilities to house technical education programs in metallurgy. It is organized in these parts: (1) Part I discusses the major purpose, underlying assumptions, recent instructional trends, and guiding principles utilized in the…

  5. Microstructural and mechanical properties of biodegradable iron foam prepared by powder metallurgy

    Czech Academy of Sciences Publication Activity Database

    Čapek, Jaroslav; Vojtěch, D.; Oborná, A.

    2015-01-01

    Roč. 83, Oct (2015), s. 468-482 ISSN 0261-3069 R&D Projects: GA ČR GBP108/12/G043 Institutional support: RVO:68378271 Keywords : powder metallurgy * metallic foams * biodegradable iron * mechanical properties * scaffolds Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.997, year: 2015

  6. Powder metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Research is reported for the tensile strength, ductility, and heat performance characterisitics of powder metallurgy (p/m) superalloys. Oxide dispersion strengthened alloys were also evaluated for their strength during thermal processing. The mechanical attributes evident in both p/m supperalloys and dispersion strengthened alloys are discussed in terms of research into their possible combination.

  7. Power metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Work conducted by NASA and NASA contractors on prealloyed superalloy powders and materials strengthened by oxide dispersion is reviewed. Fabrication, tensile strength, superplasticity, grain growth control, stress rupture life, and grain-size and dispersion-level effects are covered. Distinct strength advantages of powder metallurgy superalloys over conventional wrought alloys are noted.

  8. [Concomitant influence of occupational and social risk factors on health of workers engaged into powder metallurgy].

    Science.gov (United States)

    Shur, P Z; Zaĭtseva, N V; Kostarev, V G; Lebedeva-Nesevria, N A; Shliapnikov, D M

    2012-01-01

    Results of health risk evaluation in workers engaged into powder metallurgy, using complex of hygienic, medical, epidemiologic and sociologic studies, enable to define priority occupational and social risk factors, to assess degree of their influence on the workers' health and to identify occupationally induced diseases.

  9. Influence of fibre orientation on the performance of steel fibre-reinforced concrete

    OpenAIRE

    Grünewald, Steffen; Laranjeira de Oliveira, Filipe; Walraven, Joost; Aguado de Cea, Antonio; Molins i Borrell, Climent

    2012-01-01

    The performance of fibre-reinforced materials in the hardened state depends on the material behaviour, the production method and influences related to the structure. The position and the orientation of fibres in a structure can differ from the homogenous distribution and the random orientation in a mixer. Due to the flow of the concrete, fibres are able to orient which makes the prediction of the structural behaviour of fibre-reinforced concrete more complex, but it also offers the potential ...

  10. Strength variability of single flax fibres

    DEFF Research Database (Denmark)

    Aslan, Mustafa; Chinga-Carrasco, G.; Sørensen, Bent F.

    2011-01-01

    (linear and nonlinear) of the fibres are found to be correlated with the amount of defects. The linear stress–strain curves tend to show a higher tensile strength, a higher Young’s modulus, and a lower strain to failure than the nonlinear curves. Finally, the fibres are found to fracture by a complex......Due to the typical large variability in the measured mechanical properties of flax fibres, they are often employed only in low grade composite applications. The present study aims to investigate the reasons for the variability in tensile properties of flax fibres. It is found that an inaccuracy...

  11. Microstructural characterization of stone wool fibre network

    DEFF Research Database (Denmark)

    Chapelle, Lucie; Brøndsted, Povl; Kusano, Yukihiro

    2014-01-01

    as the number density of fibre contacts. The methods are based on image analysis of 3D datasets which have been obtained by x-ray tomography. Validation of the proposed methods was demonstrated by testing generated virtual fibrous network with known fibre characteristics.......Understanding the mechanical properties of fibrous network as complex as stone wool materials requires a relevant description of their microstructure and architecture. In this study, different methods have been proposed to characterize the fibre orientation, diameter and length of fibres as well...

  12. A novel photonic crystal fibre switch

    DEFF Research Database (Denmark)

    Alkeskjold, Thomas Tanggaard; Hermann, D.S.; Broeng, Jes

    2003-01-01

    A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB.......A new thermo-optic fibre switch is demonstrated, which utilizes the phase transitions of a thermochromic liquid crystal inside a photonic crystal fibre. We report an extinction ratio of 60 dB and an insertion loss of 1 dB....

  13. A validation of the fibre orientation and fibre length attrition prediction for long fibre-reinforced thermoplastics

    International Nuclear Information System (INIS)

    Hopmann, Ch.; Weber, M.; Haag, J. van; Schöngart, M.

    2015-01-01

    To improve the mechanical performance of polymeric parts, fibre reinforcement has established in industrial applications during the last decades. Next to the widely used Short Fibre-reinforced Thermoplastics (SFT) the use of Long Fibre-reinforced Thermoplastics (LFT) is increasingly growing. Especially for non-polar polymeric matrices like polypropylene (PP), longer fibres can significantly improve the mechanical performance. As with every kind of discontinuous fibre reinforcement the fibre orientations (FO) show a high impact on the mechanical properties. On the contrary to SFT where the local fibre length distribution (FLD) can be often neglected, for LFT the FLD show a high impact on the material’s properties and has to be taken into account in equal measure to the FOD. Recently numerical models are available in commercial filling simulation software and allow predicting both the local FOD and FLD in LFT parts. The aim of this paper is to compare i.) the FOD results and ii) the FLD results from available orientation- and fibre length attrition-models to those obtained from experimental data. The investigations are conducted by the use of different injection moulded specimens made from long glass fibre reinforced PP. In order to determine the FOD, selected part sections are examined by means of Computed Tomographic (CT) analyses. The fully three dimensional measurement of the FOD is then performed by digital image processing using grey scale correlation. The FLD results are also obtained by using digital image processing after a thermal pyrolytic separation of the polymeric matrix from the fibres. Further the FOD and the FLD are predicted by using a reduced strain closure (RSC) as well as an anisotropic rotary diffusion - reduced strain closure model (ARD-RSC) and Phelps-Tucker fibre length attrition model implemented in the commercial filling software Moldflow, Autodesk Inc., San Rafael, CA, USA

  14. Prerequisites and opportunities for repositioning of the Urals metallurgy within the Industry 4.0

    Directory of Open Access Journals (Sweden)

    O. A. Romanova

    2017-12-01

    Full Text Available The authors present the modern trends in the development of metallurgy, and classify the technological structure of metallurgical industry. The article contains specific features of the development of metallurgy in the conditions of industry formation. A special role in this process plays the pace of digitalization and robotization of the industry, the development of additive technologies, Internet of things. The authors substantiate the possibility of developing the metallurgy of the Middle Urals as a science-intensive, high-tech complex that meets the requirements of Industry 4.0. This possibility interrelates with its repositioning, one of the main tasks of which is the formation of new sales markets focused on high-tech consumer industries, as well as the preservation of traditional consumption sectors under conditions of increasing competition in the construction materials market. The authors underline the importance of international cooperation in the field of environmentally safe industrial development, with applying the best available technologies and innovative development in general. The authors propose a methodological approach for assessing the repositioning of the regional metallurgical complex. This approach is the consecutive implementation of the following stages: assessment of dynamics and the forecast of development of consumer steel products sector and its structure based on identified priority areas of technological development of metallurgy in the region; construction of a factor model describing the changes in parameters of the RMC repositioning process, and approximation of the characteristics of their nonlinear elements; building a mathematical model on the basis of neural network algorithms for assessing the process of repositioning the RMC, taking into account projected values of the RMK parameters in the process of repositioning and changing the structure of consumer markets for metal products; formation of a variable

  15. Blast Resistance of Slurry Infiltrated Fibre Concrete with Waste Steel Fibres from Tires

    Directory of Open Access Journals (Sweden)

    Drdlová Martina

    2018-01-01

    Full Text Available The utilization of waste steel fibres (coming from the recycling process of the old tires in production of blast resistant cement based panels was assessed. Waste fibres were incorporated in slurry infiltrated fibre concrete (SIFCON, which is a special type of ultra-highperformance fibre reinforced concrete with high fibre content. The technological feasibility (i.e. suitability of the waste fibres for SIFCON technology was assessed using homogeneity test. Test specimens were prepared with three volume fractions (5; 7.5 and 10 % by vol. of waste unclassified fibres. SIFCON with industrial steel fibres (10% by vol. and ultra-highperformance fibre concrete with industrial fibres were also cast and tested for comparison purposes. Quasi-static mechanical properties were determined. Real blast tests were performed on the slab specimens (500x500x40 mm according to the modified methodology M-T0-VTU0 10/09. Damage of the slab, the change of the ultrasound wave velocity propagation in the slab specimen before and after the blast load in certain measurement points, the weight of fragments and their damage potential were evaluated and compared. Realized tests confirmed the possibility of using the waste fibres for SIFCON technology. The obtained results indicate, that the usage of waste fibres does not significantly reduce the values of SIFCON flexural and compressive strength at quasi-static load - the values were comparable to the specimens with industrially produced fibres. With increasing fibre content, the mechanical parameters are increasing as well. Using of the waste fibres reduces fragmentation of SIFCON at blast load due to the fibre size parameters. Using of low diameter fibres means more fibres in the matrix and thus better homogeneity of the whole composite with less unreinforced areas. Regarding the blast tests, the specimen with waste steel fibres showed the best resistance and outperformed also the specimen with commercial fibres. Using of

  16. Optical fibre probes in the measurement of scattered light ...

    Indian Academy of Sciences (India)

    2014-01-08

    based mea- surements and sensors. An optrode usually comprises a bundle of multimode fibres, out of which one or more fibres are used for irradiating the sample, and the remaining fibres are used to collect the.

  17. Surface treated polypropylene (PP) fibres for reinforced concrete

    Energy Technology Data Exchange (ETDEWEB)

    López-Buendía, Angel M., E-mail: buendia@uv.es [AIDICO Technological Institute of Construction, Benjamin Franklin 17, 46380 Paterna, Valencia (Spain); Romero-Sánchez, María Dolores [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain); Climent, Verónica [Lafarge Cementos, Polígono Sepes, Isaac Newton s/n, 46500 Sagunto, Valencia (Spain); Guillem, Celia [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain)

    2013-12-15

    Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

  18. Powder-metallurgy preparation of NiTi shape-memory alloy using mechanical alloying and spark-plasma sintering.

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Vojtěch, V.; Knaislová, A.; Školáková, A.; Kubatík, Tomáš František; Kopeček, Jaromír

    2017-01-01

    Roč. 51, č. 1 (2017), s. 141-144 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : mechanical alloying * spark plasma sintering * NiTi * shape memory alloy Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) OBOR OECD: Materials engineering ; Materials engineering (FZU-D) Impact factor: 0.436, year: 2016 https://www.researchgate.net/publication/313900224_Powder-metallurgy_preparation_of_NiTi_shape-memory_alloy_using_mechanical_alloying_and_spark-plasma_sintering

  19. Postponed sowing does not alter the fibre/wood ratio or fibre extractability of fibre hemp (Cannabis sativa)

    NARCIS (Netherlands)

    Westerhuis, W.; Struik, P.C.; Dam, van J.E.G.; Stomph, T.J.

    2009-01-01

    Because hemp is a short-day plant, postponing the sowing date might be a suitable strategy to obtain shorter and smaller plants around flowering, when primary fibres are 'ripe' enough to be harvested. Smaller plants can be processed on existing flax scutching and hackling lines and might have fibre

  20. EXPERIMENTAL STUDY ON LIGHT TRANSMITTING CONCRETE BY USING OPTICAL FIBRE

    OpenAIRE

    S. Suganya; S. Minu Gopika

    2017-01-01

    Light transmitting concrete is one of the fibre reinforced concrete which is mainly used for aesthetic application by incorporating the optical fibres in concrete. Optical fibres help to transmit the light through the fibres and the end-light type of fibre is used to increase the aesthetic appearance of the concrete which is like a transparent concrete. Fibres are arranged in different layers, to increase the load carrying capacity and also the pattern can be created to make the concrete deco...

  1. Properties of self-compacting fibre reinforced concrete

    OpenAIRE

    Vandewalle, Lucie; Heirman, Gert

    2009-01-01

    The postcracking behaviour of fibre reinforced concrete is particularly influenced by the fibre distribution and the fibre orientation. One could suppose that in self-compacting fibre reinforced concrete (SCFRC) fibres orient along the flow due to the wall-effect, the flow direction and the velocity profile in the concrete. To investigate the fresh and hardened characteristics (mechanical properties, orientation and distribution of the fibres) of SCFRC and to relate them to those of tradition...

  2. Concretes reinforced with acrylic fibres

    Directory of Open Access Journals (Sweden)

    Amat, T.

    1997-12-01

    Full Text Available This article is based on works, carried out at the IETcc, aimed to evaluate the behaviour of concretes reinforced with acrylic polyacrylonitrile fibres, and to study the influence they have on concrete physical and mechanical properties.

    El presente artículo está basado en trabajos realizados en el Instituto de Ciencias de la Construcción Eduardo Torroja, teniendo por objetivo evaluar el comportamiento de los hormigones reforzados con fibras acrílicas de poliacrilonitrilo, estudiando la influencia que tiene sobre sus propiedades físicas y mecánicas.

  3. A PHOTONIC BAND GAP FIBRE

    DEFF Research Database (Denmark)

    1999-01-01

    An optical fibre having a periodicidal cladding structure provididing a photonic band gap structure with superior qualities. The periodical structure being one wherein high index areas are defined and wherein these are separated using a number of methods. One such method is the introduction...... of additional low index elements, another method is providing elongated elements deformed in relation to a circular cross section. Also described is a cladding structure comprising elongated elements of a material having an index of refraction higher than that of the material adjacent thereto. Using...

  4. Scintillating fibre tracking neutron detector

    International Nuclear Information System (INIS)

    Karlsson, Joakim.

    1995-04-01

    A detector for measurements of collimated fluxes of neutrons in the energy range 2-20 MeV is proposed. It utilizes (n.p) elastic scattering in scintillating optical fibres placed in successive orthogonal layers perpendicular to the neutron flux. A test module has been designed, constructed and tested with respect to separation of neutron and gamma events. The pulse height measurements show the feasibility to discriminate between neutron, gamma and background events. Application to measurements of fusion neutrons is considered. 18 refs, 22 figs, 4 tabs

  5. Human Dietary Fibre: A Review,

    Science.gov (United States)

    1979-05-01

    largely overcome by initial lipid extract iomi . 2 ) Starch can remain insoluble in the hot detergent and 1~e measure d withresidual NI )F. E nzvm u a t i...unavailable to animals. This was referred to as “crude fibre”. Crude fibre analysis consists of extract ion wit h petroleum ether , follow- ed by acid, then...with a cuticular laver on the outer surface. Potato is ~ii exani p le. (ii) Leaf Structure : These are lightl y l ignif ied , have a cut icular layer and

  6. Characterisation of Flax Fibres and Flax Fibre Composites. Being cellulose based sources of materials

    DEFF Research Database (Denmark)

    Aslan, Mustafa

    a transition value, as predicted by the volumetric composition model. This leads furthermore to a scatter in the experimental data of stiffness at high fibre weight fractions. The qualitative analysis of the composite cross sections by microscopy also shows that the low and high pressure composites have......Cellulosic fibres, like wood and plant fibres, have the potential for use as load-bearing constituents in composite materials due to their attractive properties such as high stiffness-to-weight ratio that makes cellulosic fibre composites ideal for many structural applications. There is thus...... a growing interest among composite manufacturers for such low-cost and low-weight cellulosic fibre composites. In addition, wood and plant fibre based composites with thermoplastic polymeric matrices are recyclable, and they are cost attractive alternatives to oil based fibre reinforced polymer composites...

  7. ASSESSMENT OF FIBRE CHARACTERISTICS AND SUITABILITY ...

    African Journals Online (AJOL)

    Samuel

    Key Words: Maize, husk, stalk, pulp, and fibre length. INTRODUCTION. Paper is one of the most fundamental things that is widely used by many people across the globe. The world consumption of ... around the world are used by paper industries on every continent. ..... On the fin structure of bamboo fibres. Wood Science.

  8. Winding of fibre composites; Vikling af fiberkompositter

    Energy Technology Data Exchange (ETDEWEB)

    Lystrup, Aage

    2006-01-01

    Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

  9. Insertion of optic fibre for CMS

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    The MicroJET system uses high pressure to carefully put the optical fibres into their protective tubes. These fibres are vital for rapid data transfer, but are also very delicate and, if damanged, may not work at the required efficiency. Similiar methods are used to install cables for the telecommunications industry.

  10. Fibre digestion in the hyra;r

    African Journals Online (AJOL)

    dried samples by calorimeter combustion. The fibre con- tent was determined by the method of Van Soest (1964) us- ing a Fibretec 1020 hot extraction apparatus. Two-way analysis of variance was used to test for differences between the two most important fibre digesting gut regions, the sac- culation and caeca. Results.

  11. low pump power photonic crystal fibre amplifiers

    DEFF Research Database (Denmark)

    Hougaard, Kristian G.; Broeng, Jes; Bjarklev, Anders Overgaard

    2003-01-01

    Designs of low pump power optical amplifiers, based on photonic crystal fibres are presented. The potential of these fibre amplifiers is investigated, and it is demonstrated that such amplifiers may deliver gains of more than 15 dB at 1550 nm with less than 1 mW of optical pump power....

  12. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  13. Durability of fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Hansen, Kurt Kielsgaard

    1996-01-01

    The planned research will indicate, whether fibre reinforced concrete has better or worse durability than normal concrete. Durability specimens will be measured on cracked as well as uncracked specimens. Also the pore structure in the concrete will be characterized.Keywords: Fibre reinforced...... concrete, durability, pore structure, mechanical load...

  14. Mohair, cashmere and other animal hair fibres

    CSIR Research Space (South Africa)

    Hunter, L

    2012-11-01

    Full Text Available Although luxury animal fibres, excluding silk, represent far less than 0.1% of global fibre production, they play a very significant role in the luxury, high value-added end of the market, notably the apparel market, being renowned for their special...

  15. Thermally induced structural changes in Nomex fibres

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Thermally aged Nomex fibres manifest several residual effects viz. reduction in X-ray crystallinity, weight loss and deterioration in tensile characteristics. Surface damages in the form of longi- tudinal openings, holes, material deposits etc have also been observed. Based on the data from thermally exposed fibres ...

  16. Photonic crystal fibres in the market

    DEFF Research Database (Denmark)

    Broeng, Jes; Laurila, Marko; Noordegraaf, Danny

    2011-01-01

    Photonic crystal fibres (PCFs) emerged as a research topic in the mid 1990'ies [1]. Today, 15 years later, these fibres are increasing deployed in various commercial markets. Here, we will address three of these markets; medical imaging, materials processing and sensors. We will describe how the ...

  17. Fibre optic cables for the ALICE experiment

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    These thin fibres will transmit the signal received in detectors at the ALICE experiment when it starts up with the LHC in 2008. The analogue signals produced in the detectors are first converted into digital pulse, which are transported in light down such fibres. Computers then read this digital signal to produce the final set of data.

  18. Metals in Past Societies: A Global Perspective on Indigenous African Metallurgy Shadreck Chirikure

    Energy Technology Data Exchange (ETDEWEB)

    Devanathan, Ram [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-10-01

    This slim book (166 pages) shines a spotlight on pre-industrial African metallurgy, its global connections, and anthropological implications. It integrates seemingly disparate disciplines, such as history, geology, ethnography, archeology, and metallurgy, to illustrate the diversity and innovation in metallurgy across Africa and the role of metals in the rise of socio-economic inequalities and political power. The book has 7 chapters and the focus on metals as enablers of human needs and wants is evident in each chapter. The first chapter presents the context of the work and data sources. The second chapter focuses on the origin and development of mining and metallurgy in pre-industrial Africa. Chapter 3 is dedicated to the interaction of nature and culture in the process of mining. Chapter 4 deals with the transformation of the ore into metal by smelting and the sociocultural aspects of this process. Chapter 5 explores the social and cultural roles acquired by metals as a result of fabrication into objects. Chapter 6 examines the social role of metals, trade in metals, cultural contact, proto-globalization, and technology transfer. Finally, Chapter 7 draws lessons for global anthropology from the African experience. The sources of information are adequately cited and the long list of references at the end of each chapter will be a boon to researchers in this field. The author highlights the cultural aspects and social context of the adoption of metallurgy in Africa while drawing parallels between practices in pre-industrial Africa and those in other parts of the world. The book is peppered with delightful vignettes that offer insights into the process of transforming nature into culturally significant objects. For instance, African miners, like their counterparts in Nepal and Latin America, called upon deities, spirits and ancestors to mediate between nature and humans. Women had distinct roles in this process, but there were variations in these roles and in the

  19. List of unclassified documents by the staff of Metallurgy Division, AERE Harwell from January 1979 to July 1980

    International Nuclear Information System (INIS)

    Smith, N.C.

    1980-12-01

    This list constitutes unclassified material published or presented between January 1979 and July 1980, by the staff of Metallurgy Division. It covers reports, memoranda, articles in periodicals, conference papers, books and patent specifications. (author)

  20. Insulation Characteristics of Sisal Fibre/Epoxy Composites

    Directory of Open Access Journals (Sweden)

    A. Shalwan

    2017-01-01

    Full Text Available Using natural fibres in civil engineering is the aim of many industrial and academics sectors to overcome the impact of synthetic fibres on environments. One of the potential applications of natural fibres composites is to be implemented in insulation components. Thermal behaviour of polymer composites based on natural fibres is recent ongoing research. In this article, thermal characteristics of sisal fibre reinforced epoxy composites are evaluated for treated and untreated fibres considering different volume fractions of 0–30%. The results revealed that the increase in the fibre volume fraction increased the insulation performance of the composites for both treated and untreated fibres. More than 200% insulation rate was achieved at the volume fraction of 20% of treated sisal fibres. Untreated fibres showed about 400% insulation rate; however, it is not recommended to use untreated fibres from mechanical point of view. The results indicated that there is potential of using the developed composites for insulation purposes.

  1. Review article: dietary fibre-microbiota interactions.

    Science.gov (United States)

    Simpson, H L; Campbell, B J

    2015-07-01

    Application of modern rapid DNA sequencing technology has transformed our understanding of the gut microbiota. Diet, in particular plant-based fibre, appears critical in influencing the composition and metabolic activity of the microbiome, determining levels of short-chain fatty acids (SCFAs) important for intestinal health. To assess current epidemiological, experimental and clinical evidence of how long-term and short-term alterations in dietary fibre intake impact on the microbiome and metabolome. A Medline search including items 'intestinal microbiota', 'nutrition', 'diet', 'dietary fibre', 'SCFAs' and 'prebiotic effect' was performed. Studies found evidence of fibre-influenced differences in the microbiome and metabolome as a consequence of habitual diet, and of long-term or short-term intervention (in both animals and humans). Agrarian diets high in fruit/legume fibre are associated with greater microbial diversity and a predominance of Prevotella over Bacteroides. 'Western'-style diets, high in fat/sugar, low in fibre, decrease beneficial Firmicutes that metabolise dietary plant-derived polysaccharides to SCFAs and increase mucosa-associated Proteobacteria (including enteric pathogens). Short-term diets can also have major effects, particularly those exclusively animal-based, and those high-protein, low-fermentable carbohydrate/fibre 'weight-loss' diets, increasing the abundance of Bacteroides and lowering Firmicutes, with long-term adherence to such diets likely increasing risk of colonic disease. Interventions to prevent intestinal inflammation may be achieved with fermentable prebiotic fibres that enhance beneficial Bifidobacteria or with soluble fibres that block bacterial-epithelial adherence (contrabiotics). These mechanisms may explain many of the differences in microbiota associated with long-term ingestion of a diet rich in fruit and vegetable fibre. © 2015 The Authors. Alimentary Pharmacology & Therapeutics published by John Wiley & Sons Ltd.

  2. Thermal stability and creep behaviour of MgNiYCe-rich mischmetal alloys processed by a powder metallurgy route

    Czech Academy of Sciences Publication Activity Database

    Peréz, P.; Milička, Karel; Badia, J. M.; Garcés, G.; Antoranz, J. M.; Gonzáles, S.; Dobeš, Ferdinand; Adeva, P.

    289-292, - (2009), s. 127-136 ISSN 1012-0386. [DIMAT 2008, International Conference on Diffusion in Materials /7./. Lanzarote, Canary Islands, 28.10.2008-31.10.2008] Grant - others:Ministerio de Ciencia y Tecnologia (ES) MAT2006-11731-C02 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * powder metallurgy * microstructure * thermal stability * creep Subject RIV: JG - Metallurgy

  3. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  4. Computational predictions of the tensile properties of electrospun fibre meshes: effect of fibre diameter and fibre orientation.

    Science.gov (United States)

    Stylianopoulos, Triantafyllos; Bashur, Chris A; Goldstein, Aaron S; Guelcher, Scott A; Barocas, Victor H

    2008-10-01

    The mechanical properties of biomaterial scaffolds are crucial for their efficacy in tissue engineering and regenerative medicine. At the microscopic scale, the scaffold must be sufficiently rigid to support cell adhesion, spreading, and normal extracellular matrix deposition. Concurrently, at the macroscopic scale the scaffold must have mechanical properties that closely match those of the target tissue. The achievement of both goals may be possible by careful control of the scaffold architecture. Recently, electrospinning has emerged as an attractive means to form fused fibre scaffolds for tissue engineering. The diameter and relative orientation of fibres affect cell behaviour, but their impact on the tensile properties of the scaffolds has not been rigorously characterized. To examine the structure-property relationship, electrospun meshes were made from a polyurethane elastomer with different fibre diameters and orientations and mechanically tested to determine the dependence of the elastic modulus on the mesh architecture. Concurrently, a multiscale modelling strategy developed for type I collagen networks was employed to predict the mechanical behaviour of the polyurethane meshes. Experimentally, the measured elastic modulus of the meshes varied from 0.56 to 3.0 MPa depending on fibre diameter and the degree of fibre alignment. Model predictions for tensile loading parallel to fibre orientation agreed well with experimental measurements for a wide range of conditions when a fitted fibre modulus of 18 MPa was used. Although the model predictions were less accurate in transverse loading of anisotropic samples, these results indicate that computational modelling can assist in design of electrospun artificial tissue scaffolds.

  5. Effects of Extrusion on Fibre Length in Sisal Fibre-Reinforced Polypropylene Composites

    Science.gov (United States)

    Pathi, Sridhar; Jayaraman, Krishnan

    Natural fibre reinforced thermoplastic composites find a wide array of applications in the automobile, building and construction industries. These composites are mostly produced by injection moulding or extrusion through properly designed dies. During these production processes, the shear forces exerted by the screw or ram leads to the degradation of the natural fibres. A screwless extruder that minimises fibre degradation and employs a reliable and low technology process has already been developed. However, the fibre degradation caused by the screwless extruder has not been compared with that of the conventional extruders. So, this study is focused on the influence of extrusion processes on the degradation of natural fibres in thermoplastic composites. Sisal fibres of 10 mm length were extruded with polypropylene, to furnish extrudates with a fibre mass fraction of 25%, using conventional single screw and screwless extruders. Polypropylene in the extrudates was dissolved in Xylene in a Sohxlet process; the fibres that were extracted were analysed for length variations. While fibre degradation in the form of fibre length variation is similar in both cases, this can be minimised in screwless extrusion by extending the gap between the front face of the cone and the orifice plate.

  6. Influence of Cellulosic Fibres on the Physical Properties of Fibre Cement Composites

    Science.gov (United States)

    Hospodarova, V.; Stevulova, N.; Vaclavik, V.; Dvorsky, T.

    2017-10-01

    Nowadays, there are new approaches directing to processing of non-conventional fibre-cement composites for application in the housing construction. Vegetable cellulosic fibres coming from natural resources used as reinforcement in cost-effective and environmental friendly building products are in the spotlight. The applying of natural fibres in cement based composites is narrowly linked to the ecological building sector, where a choice of materials is based on components including recyclable, renewable raw materials and low-resource manufacture techniques. In this paper, two types of cellulosic fibres coming from wood pulp and recycled waste paper with 0.2%; 0.3% and 0.5% of fibre addition into cement mixtures were used. Differences in the physical characteristics (flowability, density, coefficient of thermal conductivity and water absorbability) of 28 days hardened fibre-cement composites are investigated. Addition of cellulosic fibres to cement mixture caused worsening the workability of fresh mixture as well as absorbability of hardened composites due to hydrophilic nature of biomaterial, whereas density and thermal conductivity of manufactured cement based fibre plaster are enhanced. The physical properties of cement plasters based on cellulosic fibres depend on structural, physical characteristics of cellulosic fibres, their nature and processing.

  7. Structural and electrical properties of copper-nickel-aluminum alloys obtained by conventional powder metallurgy method

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Silveira, C.R. da; Pertile, H.K.S., E-mail: fisica.cch@mackenzie.br [Universidade Presbiteriana Mackenzie (UPM/CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades. Dept. de Fisica; Silva, L.C.E. da; Buso, S.J., E-mail: jgcarrio@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    This work looked for to search out systematically, in scale of laboratory, copper-nickel-aluminum alloys (Cu-Ni-Al) with conventional powder metallurgy processing, in view of the maintenance of the electric and mechanical properties with the intention of getting electric connectors of high performance or high mechanical damping. After cold uniaxial pressing (1000 kPa), sintering (780 deg C) and convenient homogenization treatments (500 deg C for different times) under vacuum (powder metallurgy), the obtained Cu-Ni-Al alloys were characterized by optical microscopy, electrical conductivity, Vickers hardness. X rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, hardness, macrostructures and microstructures of the samples. (author)

  8. Structural and electrical properties of copper-nickel-aluminum alloys obtained by conventional powder metallurgy method

    International Nuclear Information System (INIS)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Silveira, C.R. da; Pertile, H.K.S.

    2009-01-01

    This work looked for to search out systematically, in scale of laboratory, copper-nickel-aluminum alloys (Cu-Ni-Al) with conventional powder metallurgy processing, in view of the maintenance of the electric and mechanical properties with the intention of getting electric connectors of high performance or high mechanical damping. After cold uniaxial pressing (1000 kPa), sintering (780 deg C) and convenient homogenization treatments (500 deg C for different times) under vacuum (powder metallurgy), the obtained Cu-Ni-Al alloys were characterized by optical microscopy, electrical conductivity, Vickers hardness. X rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, hardness, macrostructures and microstructures of the samples. (author)

  9. Development of new metal matrix composite electrodes for electrical discharge machining through powder metallurgy process

    Directory of Open Access Journals (Sweden)

    C. Mathalai Sundaram

    2014-12-01

    Full Text Available Electrical discharge machining (EDM is one of the widely used nontraditional machining methods to produce die cavities by the erosive effect of electrical discharges. This method is popular due to the fact that a relatively soft electrically conductive tool electrode can machine hard work piece. Copper electrode is normally used for machining process. Electrode wear rate is the major drawback for EDM researchers. This research focus on fabrication of metal matrix composite (MMC electrode by mixing copper powder with titanium carbide (TiC and Tungsten carbide (WC powder through powder metallurgy process, Copper powder is the major amount of mixing proportion with TiC and WC. However, this paper focus on the early stage of the project where powder metallurgy route was used to determine suitable mixing time, compaction pressure and sintering and compacting process in producing EDM electrode. The newly prepared composite electrodes in different composition are tested in EDM for OHNS steel.

  10. Quantifying the properties of low-cost powder metallurgy titanium alloys

    International Nuclear Information System (INIS)

    Bolzoni, L.; Ruiz-Navas, E.M.; Gordo, E.

    2017-01-01

    The extensive industrial employment of titanium is hindered by its high production costs where reduction of these costs can be achieved using cheap alloying elements and appropriate alternative processing techniques. In this work the feasibility of the production of low-cost titanium alloys is addressed by adding steel to pure titanium and processing the alloys by powder metallurgy. In particular, a spherical 4140 LCH steel powder commonly used in metal injection moulding is blended with irregular hydride-dehydride Ti. The new low-cost alloys are cold uniaxially pressed and sintered under high vacuum and show comparable properties to other wrought-equivalent and powder metallurgy titanium alloys. Differential thermal analysis and X-ray diffraction analyses confirm that Ti can tolerate the employment of iron as primary alloying element without forming detrimental TiFe-based intermetallic phases. Thus, the newly designed α+β alloys could be used for cheaper non-critical components.

  11. Preparation of Three-Dimensional Graphene Foams Using Powder Metallurgy Templates.

    Science.gov (United States)

    Sha, Junwei; Gao, Caitian; Lee, Seoung-Ki; Li, Yilun; Zhao, Naiqin; Tour, James M

    2016-01-26

    A simple and scalable method which combines traditional powder metallurgy and chemical vapor deposition is developed for the synthesis of mesoporous free-standing 3D graphene foams. The powder metallurgy templates for 3D graphene foams (PMT-GFs) consist of particle-like carbon shells which are connected by multilayered graphene that shows high specific surface area (1080 m(2) g(-1)), good crystallization, good electrical conductivity (13.8 S cm(-1)), and a mechanically robust structure. The PMT-GFs did not break under direct flushing with DI water, and they were able to recover after being compressed. These properties indicate promising applications of PMT-GFs for fields requiring 3D carbon frameworks such as in energy-based electrodes and mechanical dampening.

  12. [Investigation about prevention behavior for dust workers in machinery, ceramic, and metallurgy industry].

    Science.gov (United States)

    Shen, Fu-hai; Ma, Qing-kun; Xiao, Shu-yu; Cui, Feng-tao; Meng, Qing-di; Yang, Xiu-qing; Qi, Hui-sheng; Fan, Xue-yun; Yao, San-qiao

    2011-01-01

    The purposes of this thesis were to study the behavior about workers exposed to dust and provide scientific basis for health promotion. We designed a questionnaire and carry it on the 746 dust workers in the 3 representative corporations of Machinery, Ceramic, and Metallurgy Industry. All data were input into computer. And a database was established with Excel. SPSS11.5 statistical analysis software was used to analyze the influence on protecting behavioral between the application of qualifications, different jobs, training or protection, and other aspects etc. The rates were 94.4% and 75.3% about the regular physical examination and requirements for protective equipment. The rate of choosing an effective way of protection was generally low (15.4%). There was significant difference for among different educational background workers (P Metallurgy Industry. Those who were not educated had a lower using rate about the protection behavior, regular physical examination, and requirements for protective equipment than those educated.

  13. [Risk and features of occupational diseases in nonferrous metallurgy workers of Kolsky Transpolar area].

    Science.gov (United States)

    Siurin, S A; Chashchin, V P; Frolova, N M

    2015-01-01

    The study covered data on 977 cases of occupational diseases in 615 workers of nonferrous metallurgy in Kolsky Transpolar area. Findings are high risk of occupational diseases in workers engaged into electrolysis production of aluminium, all nickel reprocessing and pyrometallic copper reprocessing (GR 7.02-10.0). Electrolysis operators and anode operators of aluminium production are more prone to occupational diseases, with bone and muscular disorders (46.8%) prevalent in the morbidity structure. Respiratory diseases are more prevalent (68.2-100%) in the occupational morbidity structure of copper-nickelindustry workers. Conclusion is made on mandatory improvement of the work conditions and more effective individual protective means against occupational hazards in workers of nonferrous metallurgy in Kolsky Transpolar area.

  14. Estimation and characterization of polycyclic aromatic hydrocarbons from magnesium metallurgy facilities in China.

    Science.gov (United States)

    Nie, Zhiqiang; Yang, Yufei; Tang, Zhenwu; Liu, Feng; Wang, Qi; Huang, Qifei

    2014-11-01

    Field monitoring was conducted to develop a polycyclic aromatic hydrocarbon (PAH) emission inventory for the magnesium (Mg) metallurgy industry in China. PAH emissions in stack gas and fly/bottom ash samples from different smelting units of a typical Mg smelter were measured and compared. Large variations of concentrations, congener patterns, and emission factors of PAHs during the oxidation and reduction stages in the Mg smelter were observed. The measured average emission factor (166,487 μg/t Mg) was significantly higher than those of other industrial sources. Annual emission from Mg metallurgy in 2012 in China was estimated at 116 kg (514 g BaPeq) for PAHs. The results of this study suggest that PAH emission from Mg industries should be considered by local government agencies. These data may be helpful for understanding PAH levels produced by the Mg industry and in developing a PAH inventory.

  15. Mechanical properties of metals for biomedical applications using powder metallurgy process: A review

    Science.gov (United States)

    Dewidar, Montasser Marasy; Yoon, Ho-Chel; Lim, Jae Kyoo

    2006-06-01

    The uses of biomaterials have been revolutionizing the biomedical field in deployment as implants for humans. During the past five decades, many implant materials made of metals have been put into practical use. Powder metallurgy techniques have been used to produce controlled porous structures, such as porous coatings applied for dental and orthopedic surgical implants, which allow bony tissue ingrowth within the implant surface, thereby improving fixation. This paper examines various important metals using powder metallurgy technology to produce elements of a total hip replacement. These alloys are 316L stainless steel alloy, Co-Cr-Mo alloy, and Ti-6Al-4V alloy. Also, this paper examines current information on the mechanical properties. Mechanical properties are discussed as a function of type of materials and process of fabrication. This article addresses the engineering aspects concerning the advantages and disadvantages of each type of material.

  16. Metallurgy Department. Progress Report for the Period 1 January to 31 December 1984

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its...... activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1984 is included....

  17. Metallurgy Department progress report for the period 1 January to 31 December 1986

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1987-04-01

    The activities of the Metallurgy Department at Risoe during 1986 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1986 is included. (editors)

  18. Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Březina, M.; Minda, J.; Doležal, P.; Krystýnová, M.; Fintová, Stanislava; Zapletal, J.; Wasserbauer, J.; Ptáček, P.

    2017-01-01

    Roč. 7, č. 11 (2017), č. článku 461. ISSN 2075-4701 Institutional support: RVO:68081723 Keywords : magnesium * powder metallurgy * cold pressing * hot pressing * EIS (Electrochemical impedance spectroscopy) * three-point bending test * corrosion Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 1.984, year: 2016 http://www.mdpi.com/2075-4701/7/11/461

  19. Metallurgy department progress report for the period 1 January to 31 December 1977

    International Nuclear Information System (INIS)

    1978-03-01

    The activities of the Metallurgy Department at Risoe during 1977 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel elements, and Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1977 is included. (author)

  20. Metallurgy Department progress report for the period 1 January to 31 December 1985

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde Soerensen, J.B.

    1986-04-01

    The activities of the Metallurgy department at Risoe during 1985 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1985 is included. (author)

  1. Production of titanium alloys for advanced aerospace systems by powder metallurgy

    OpenAIRE

    Henriques, Vinicius André Rodrigues; Campos, Pedro Paulo de; Cairo, Carlos Alberto Alves; Bressiani, José Carlos

    2005-01-01

    Titanium alloys parts are ideally suited for advanced aerospace systems because of their unique combination of high specific strength at both room temperature and moderately elevated temperature, in addition to excellent corrosion resistance. Despite these features, use of titanium alloys in engines and airframes is limited by cost. The alloys processing by powder metallurgy eases the obtainment of parts with complex geometry. In this work, results of the Ti-6Al-4V and Ti-13Nb-13Zr alloys pro...

  2. Production of a low young modulus titanium alloy by powder metallurgy

    OpenAIRE

    Santos,Dalcy Roberto dos; Henriques,Vinicius André Rodrigues; Cairo,Carlos Alberto Alves; Pereira,Marcelo dos Santos

    2005-01-01

    Titanium alloys have several advantages over ferrous and non-ferrous metallic materials, such as high strengthto-weight ratio and excellent corrosion resistance. A blended elemental titanium powder metallurgy process has been developed to offer low cost commercial products. The process employs hydride-dehydride (HDH) powders as raw material. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy due to its lower modulus of elasticity and high biocompatibility is a prom...

  3. A Comparison of the Plastic Flow Response of a Powder Metallurgy Nickel Base Superalloy (Postprint)

    Science.gov (United States)

    2017-04-01

    Materials The nickel-base, powder-metallurgy (PM) cc¢ super- alloy LSHR was used to establish the effect of test method on plastic -flow response under hot...of friction was estimated to lead to maximum errors in flow stress of the order of 3 pct for the sample geometry and height reduction used in the... plastic -flow behavior of LSHR (in effective stress-strain terms) was described using a phenomeno- logical relationship typical of those for

  4. Metallurgy department progress report for the period 1 January to 31 December 1980

    International Nuclear Information System (INIS)

    1981-07-01

    The activities of the Metallurgy Department at Risoe during 1980 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel Elements, Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1980 is included. (Author)

  5. Review of some past and present powder metallurgy programs at the Los Alamos Scientific Laboratory

    International Nuclear Information System (INIS)

    Sheinberg, H.

    1977-01-01

    Powder metallurgy programs at LASL are reviewed. Topics covered include: KIWI reactor fuel elements; Phoebus reactor fuel elements, criticality control and poison plate material, structural composites for fuel element supports, and heat shields for fuel element supports; thermionic emitter reactor uranium carbide--zirconium carbide fuel pins, and molybdenum--uranium oxide fuel pins; laser and electron beam fusion targets; and current work in MHD components

  6. Situation of radioactive wastes and their prevention and treatment measures in China's uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Li Renjie.

    1988-01-01

    The sorts of radioactive wastes produced in uranium mining and metallurgy and their hazards are discribed in this paper. The characteristics of the radioactive wastes are discussed. The measurements and results are introduced for treatment and disposal of the radioactive wastes. The way to deal with prevention and treatment of radioactive wastes is presented in the stages of engineering design, construction, production and decommission of uranium mines and plants

  7. Extractive metallurgy of the beryllium; Fundamentos da metalurgia extrativa do berilio

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, Neusa; Capocchi, Jose Deodoro Trani [Sao Paulo Univ., SP (Brazil). Escola Politecnica

    1995-07-01

    A bibliographic review is performed on the beryllium extractive metallurgy. The work describes the main type of ores and processes applied to the metallic beryllium production, beryllium oxide production using fluoride, sulfide and direct chlorination. The thermodynamic consideration are made on beryllium reduction processes, discussing the viability of the beryllium oxide and hallide reduction processes. Under the technological viewpoint, the Cu-Be alloys main production processes are discussed, and the main toxicity problems related with beryllium are mentioned 15 refs..

  8. Metallurgy department progress report for the period 1 January to 31 December 1978

    International Nuclear Information System (INIS)

    1979-04-01

    The activities of the metallurgy department at Risoe during 1978 are described. The work is presented in four chapters: General materials research, technology and materials development, fuel elements, and non-destructive testing. Furthermore, a survey is given of the depratment's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1978 is included. (author)

  9. Investigation of a thermoplastic-powder metallurgy process for the fabrication of porous niobium rods

    International Nuclear Information System (INIS)

    Nordin, D.R.

    1978-06-01

    The feasibility of using a thermoplastic-powder metallurgy technique for the fabrication of porous niobium rods was investigated. Some early problems were overcome to successfully extrude the polymer coated niobium powder into long lengths. The effects of certain process variables were investigated. Residual porosity and extrusion pressure were found to be regulated by the polymer fraction. The procedures for taking the extruded polystyrene--niobium rods through the heat treatments to the final, tin infiltrated stage are explained

  10. Metallurgy department progress report for the period 1 January to 31 December 1983

    International Nuclear Information System (INIS)

    1984-06-01

    The activities of the Metallurgy Department at Risoe during 1983 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. Furthermore, a survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1983 is included. (author)

  11. Ceramic fibres for the automotive industry

    Energy Technology Data Exchange (ETDEWEB)

    Fryatt, J.

    1985-01-01

    The outstanding thermal, physical and chemical properties of ceramic fibres make them a noticeable contender for inclusion in engineered systems to satisfy such performance demands. A wide range of fibres and fibre-based products are available which exhibit such characteristics as high temperature continuous service ability (1600/sup 0/C if required), low thermal conductivity, excellent resistance to chemical attack (including reducing conditions), good acoustic performance at all temperatures and good resistance to vibration. They are also lightweight, fireproof and incombustible. Ceramic fibres should really be referred to as refractory fibres as they are based on combinations of high purity alumina and silica. Two groups of products exist. The most common have a continuous-use temperature of 1260/sup 0/C. These fibres are characterized by an alumina content of 40-50% but refractoriness and temperature use limit can be increased to about 1400/sup 0/C by modifying the basic chemistry. This generally involves increasing the alumina content to as much as 62% or adding chromia or zirconia to the basic mix. The second and less common group of fibres is characterized by both chemistry and crystal morphology. Chemistry is biased towards a high alumina content (over 70%), while production routes are designed to yield as high a crystal phase (and so enhanced high temperature stability) as possible.

  12. Oxidation of lignin in hemp fibres by laccase: effects on mechanical properties of hemp fibres and unidirectional fibre/epoxy composites

    DEFF Research Database (Denmark)

    Liu, Ming; Baum, Andreas; Odermatt, Jürgen

    2017-01-01

    Laccase activity catalyzes oxidation and polymerization of phenols. The effect of laccase treatment on the mechanical properties of hemp fibres and hemp fibre/epoxy composites was examined. Laccase treatment on top of 0.5% EDTA + 0.2% endo-polygalacturonase (EPG) treatments increased the mechanical...... properties of hemp fibres and fibre/epoxy composites. Comparing all fibre treatments, composites with 0.5% EDTA + 0.2% EPG + 0.5% laccase treated fibres had highest stiffness of 42 GPa and highest ultimate tensile strength (UTS) of 326 MPa at a fibre volume content of 50%. The thermal resistance of hemp...... hemp fibres and their composites were due to laccase catalyzed polymerization of lignin moieties in hemp fibres....

  13. Effect of repressing on the mechanical properties of the valve guides manufactured by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Andrés Rodríguez-Spitia

    2017-03-01

    Full Text Available Characterization of hardness, mass loss, and friction coefficient, was carried out on valve guides for internal combustion engines, manufactured by powder metallurgy, with the aim of finding out if they fulfill the requirements of an internal combustion engine and to be mass produced. Currently available brass casting valve guides were used as comparative parameter. It was analyzed whether properties were present in a homogeneous way in the piece lengthwise; the additional repressing process carried out in the production line with respect to the sintered guides was evaluated. Therefore, Brinell, Vickers and dry slip pin-on-disk tests were done in order to determine the friction coefficient and the wear rate. Scanning electron microscopy SEM and the metallographic analysis were used to study the wear mechanism, chemical composition of the guides, and the effect of repressing -quantifying the porosity. It was clear that these pieces manufactured by powder metallurgy process showed lower values in their mechanical-tribological properties compared to commercially available valve guides taken as reference. With these results, the company which manufactures the guides by powder metallurgy will make some adjustments suggested for the parameters at the guide’s production line.

  14. Manufacture of good-weldable low oxygen molybdenum by powder metallurgy

    International Nuclear Information System (INIS)

    Hiraoka, Yutaka; Okada, Masatoshi; Akiyama, Takashi; Yamafuchi, Yasuo.

    1984-01-01

    In general most of commercial molybdenum is produced by the powder metallurgy method and is utilized as a superior heat-resisting material in many fields. Moreover, molybdenum is expected to be used as the first-wall components of JT-60 (JAERI Tokamak-60). However, one of major problems on molybdenum, particularly on powder metallurgy molybdenum, is that any sound welded joint is hard to be obtainable. In many cases weld pores are formed on welding and, therefore, ductility of the welded joint is severely degraded. The object of the present work is to get a sound welded joint without any weld pores by reducing impurity levels in the material. The materials were produced by modifying one or several parts in the ordinary manufacturing process of powder metallurgy molybdenum. Oxygen, nitrogen, carbon and other principal metallic impurities were chemically analysed. The above materials were then subjected to electron-beam-welding by using a melt-run technique, and the soundness of the welded joints was examined by optical microscopy. (author)

  15. Properties of WZ21 (%wt) alloy processed by a powder metallurgy route.

    Science.gov (United States)

    Cabeza, Sandra; Garcés, Gerardo; Pérez, Pablo; Adeva, Paloma

    2015-06-01

    Microstructure, mechanical properties and corrosion behaviour of WZ21 (%wt) alloy prepared by a powder metallurgy route from rapidly solidified powders have been studied. Results were compared to those of the same alloy prepared through a conventional route of casting and extrusion. The microstructure of the extruded ingot consisted of α-Mg grains and Mg3Zn3Y2 (W-phase) and LPSO-phase particles located at grain boundaries. Moreover, stacking faults were also observed within α-Mg grains. The alloy processed by the powder metallurgy route exhibited a more homogeneous and finer microstructure, with a grain size of 2 μm. In this case W-phase and Mg24Y5 phase were identified, but not the LPSO-phase. The microstructural refinement induced by the use of rapidly solidified powders strengthened the alloy at room temperature and promoted superplasticity at higher strain rates. Corrosion behaviour in PBS medium evidenced certain physical barrier effect of the almost continuous arrangements of second phases aligned along the extrusion direction in conventionally processed WZ21 alloy, with a stable tendency around 7 mm/year. On the other hand, powder metallurgy processing promoted significant pitting corrosion, inducing accelerated corrosion rate during prolonged immersion times. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. A millennium of metallurgy recorded by lake sediments from Morococha, Peruvian Andes.

    Science.gov (United States)

    Cooke, Colin A; Abbott, Mark B; Wolfe, Alexander P; Kittleson, John L

    2007-05-15

    To date, information concerning pre-Colonial metallurgy in South America has largely been limited to the archaeological record of artifacts. Here, we reconstruct a millennium of smelting activity in the Peruvian Andes using the lake-sediment stratigraphy of atmospherically derived metals (Pb, Zn, Cu, Ag, Sb, Bi, and Ti) and lead isotopic ratios (206Pb/ 207Pb) associated with smelting from the Morococha mining region in the central Peruvian Andes. The earliest evidence for metallurgy occurs ca. 1000 A.D., coinciding with the fall of the Wari Empire and decentralization of local populations. Smelting during this interval appears to have been aimed at copper and copper alloys, because of large increases in Zn and Cu relative to Pb. A subsequent switch to silver metallurgy under Inca control (ca. 1450 to conquest, 1533 A.D.) is indicated by increases in Pb, Sb, and Bi, a conclusion supported by further increases of these metals during Colonial mining, which targeted silver extraction. Rapid development of the central Andes during the 20th century raised metal burdens by an order of magnitude above previous levels. Our results represent the first evidence for pre-Colonial smelting in the central Peruvian Andes, and corroborate the sensitivity of lake sediments to pre-Colonial metallurgical activity suggested by earlier findings from Bolivia.

  17. Degradation of dietary fibre from 'Gari' by faecal bacteria and ...

    African Journals Online (AJOL)

    Dietary fibre (soluble and insoluble fibre) was extracted from 'gari' (a fermented cassava product). The 'gari' fibre was subjected to degradation by faecal microflora and the microbial extracellular enzymes obtained from six clinically healthy adults (S1-S6). Other common components of dietary fibre namely starch, xylan, ...

  18. Effects of moisture on the mechanical properties of glass fibre ...

    Indian Academy of Sciences (India)

    Unknown

    SEM study of the fractured surfaces showed heavy fibre pull-out in the tensile zone whilst shear fracture of the fibre bundles was predominant at the compressive zone of the samples tested for flexural strength properties. Keywords. Nascent glass fibre; vinylester resin; moisture effects; fibre pull-out. 1. Introduction. Over the ...

  19. Assessment of Fibre Characteristics and Suitability of Maize Husk ...

    African Journals Online (AJOL)

    Maize husk and stalk were assessed for their fibre characteristics and suitability for pulp and paper production. Fifteen (15) fibres were randomly selected and measured from each representative sample. It was observed that fibre length of maize husk was 1.37mm and that of maize stalk was 1.52mm. The fibre diameter (D) ...

  20. Mechanical properties of natural fibre reinforced polymer composites

    Indian Academy of Sciences (India)

    Wintec

    green composites involving Hibiscus sabdariffa fibre as a reinforcing material in urea–formaldehyde (UF) resin based polymer ... mixed Hibiscus sabdariffa fibre reinforced polymer composites such as tensile, compressive and wear proper- ties were ... in natural fibres and its applications in various fields. Natural fibres are ...

  1. Mechanical properties of natural fibre reinforced polymer composites

    Indian Academy of Sciences (India)

    Wintec

    forcing materials such as glass fibre, carbon fibre etc are their specific ... this is the substitution of inorganic fibres such as glass or aramid fibres by .... friction. The samples were tested with different loads vary- ing from 1–3 kg. For each load the machine was allowed to run for 15 min and the readings were recorded. After.

  2. Dietary fibre: new frontiers for food and health

    National Research Council Canada - National Science Library

    Kamp, J. W. van der

    2010-01-01

    ... papers of the Dietary fibre analysis workshop and the HEALTHGRAIN Symposium Cereal grain fibre and health , both held in conjunction with DF09. This book is titled Dietary fibre- new frontiers for food and health . With the adoption - after decades of debate - of almost identical definitions of dietary fibre by Codex Alimentarius and the European Un...

  3. Comparison of two novel approaches to model fibre reinforced concrete

    NARCIS (Netherlands)

    Radtke, F.K.F.; Simone, A.; Sluys, L.J.

    2009-01-01

    We present two approaches to model fibre reinforced concrete. In both approaches, discrete fibre distributions and the behaviour of the fibre-matrix interface are explicitly considered. One approach employs the reaction forces from fibre to matrix while the other is based on the partition of unity

  4. Enhancement of Short Chain Fatty Acid Production from Millet Fibres ...

    African Journals Online (AJOL)

    Dietary fibre was extracted from two millet varieties viz Pearl millet, Pennisetum glaucum (PM) and Foxtail millet (FxM, Setaria italica), and separated into total dietary fibre (TDF), insoluble dietary fibre (IDF) and soluble dietary fibre (SDF). Four probiotic bacteria (Lactobacillus rhamnosus, Lactobacillus acidophilus, ...

  5. factors that improve the impact responses of ukam plant fibre ...

    African Journals Online (AJOL)

    mat, woven rovings, surface tissues, continu- ous strand mat and woven cloth webbing. In fibre reinforced composites, high- strength fibres are incased within a tough ma- trix. The functions of the matrix are to bond the fibres together, protect them against dam- ages and transmit load from fibre to another. According to Harris ...

  6. Plant fibre composites - porosity and stiffness

    DEFF Research Database (Denmark)

    Madsen, Bo; Thygesen, Anders; Lilholt, Hans

    2009-01-01

    of the composites with their mechanical properties. The fibre weight fraction is used as an independent parameter to calculate the complete volumetric composition. A maximum obtainable stiffness of the composites is calculated at a certain transition fibre weight fraction, which is characterised by a best possible...... combination of high fibre volume fraction and low porosity. The model is validated with experimental data from the literature on several types of composites. A stiffness diagram is presented to demonstrate that the calculations can be used for tailoring and design of composites with a given profile...... of properties. (C) 2009 Elsevier Ltd. All rights reserved....

  7. Higher order modes of coupled optical fibres

    International Nuclear Information System (INIS)

    Alexeyev, C N; Yavorsky, M A; Boklag, N A

    2010-01-01

    The structure of hybrid higher order modes of two coupled weakly guiding identical optical fibres is studied. On the basis of perturbation theory with degeneracy for the vector wave equation expressions for modes with azimuthal angular number l ≥ 1 are obtained that allow for the spin–orbit interaction. The spectra of polarization corrections to the scalar propagation constants are calculated in a wide range of distances between the fibres. The limiting cases of widely and closely spaced fibres are studied. The obtained results can be used for studying the tunnelling of optical vortices in directional couplers and in matters concerned with information security

  8. A target fibre study on seats in public houses.

    Science.gov (United States)

    Kelly, E; Griffin, R M

    1998-01-01

    A target fibre survey was conducted to assess the random occurrence of a blue wool fibre on seats in public houses throughout the United Kingdom. Fibre tape lifts were taken from 80 seats. Four seats yielded matching fibres and five of these were found on one seat. A total of 292 fibres were identified; nine fibres proved indistinguishable from the target after comparison microscopy, microspectro-photometry and attempts at thin layer chromatography, and two of these fibres were still apparently indistinguishable after TLC analysis although only one dye component was visible.

  9. Inhibition of starch absorption by dietary fibre. A comparative study of wheat bran, sugar-beet fibre, and pea fibre

    DEFF Research Database (Denmark)

    Hamberg, O; Rumessen, J J; Gudmand-Høyer, E

    1989-01-01

    The effect of dietary fibre on starch absorption was investigated in 8 healthy subjects. Amounts of starch escaping small-bowel absorption was assessed by comparison of breath H2 excretion after test meals and after lactulose (10g). After ingestion of bread made from 100g of wheat flour increases...... that the dietary fibres used in this impaired the absorption of wheat starch and thereby increased the amount of starch-derived carbohydrate available for colonic fermentation....... in H2 excretion occurred in all subjects; the calculated fractions of unabsorbed starch ranged from 4% to 17% (median, 8%). Concurrent ingestion of this bread with either wheat bran, sugar-beet fibre, or pea fibre increased the fraction of unabsorbed starch to 12.5% (5-22%) (p less than 0.05), 12.5% (5...

  10. Fibre Bragg Grating and Long Period Grating Sensors in Polymer Optical Fibres

    OpenAIRE

    Bundalo, Ivan-Lazar; Bang, Ole; Nielsen, Kristian

    2017-01-01

    The work presented in this thesis focuses on improving the fabrication of Fibre Bragg Gratings (FBGs) and Long Period Gratings (LPGs) in microstructure polymer optical fibres (mPOF). It also focuses on exploring new options for biomedical and acoustic sensing with the purpose of expanding the range of applications and pushing the limits. The first part of the work focuses on the fabrication of FBGs in polymer optical fibres. FBGs are a periodic perturbation of the refractive index of the opti...

  11. Hybrid RSOA and fibre raman amplified long reach feeder link for WiMAX-on-fibre

    DEFF Research Database (Denmark)

    Amaya Fernández, Ferney Orlando; Martinez, Javier; Yu, Xianbin

    2009-01-01

    A distributed fibre Raman amplified long reach optical access feeder link using a reflective semiconductor optical amplifier in the remote base station is experimentally demonstrated for supporting WiMAXover- fibre transmission. The measured values for the error vector magnitude for quadrature ph...... phase shift keying and 16-ary quadrature amplitude modulation after 40 km of fibre transmission meet the IEEE 820.16 standard requirements...

  12. Shrinkage Behaviour of Fibre Reinforced Concrete with Recycled Tyre Polymer Fibres

    OpenAIRE

    Marijana Serdar; Ana Baričević; Marija Jelčić Rukavina; Martina Pezer; Dubravka Bjegović; Nina Štirmer

    2015-01-01

    Different types of fibres are often used in concrete to prevent microcracking due to shrinkage, and polypropylene fibres are among the most often used ones. If not prevented, microcracks can lead to the development of larger cracks as drying shrinkage occurs, enabling penetration of aggressive substances from the environment and reducing durability of concrete structures. The hypothesis of the present research is that polypropylene fibres, used in concrete for controlling formation of microcr...

  13. Compression moulding of composites with hybrid fibre architectures

    OpenAIRE

    Corbridge, D.M.; Harper, Lee Thomas; De Focatiis, Davide S.A.; Warrior, N.A.

    2016-01-01

    Advanced Sheet Moulding Compounds (ASMC) and unidirectional (UD) prepregs have been co-compression moulded to form a hybrid composite material. In-mould flow influences the UD fibre architecture in two ways. When UD fibres are aligned transversely to the ASMC flow direction, shearing occurs which causes local changes in fibre volume fraction and fibre waviness. When the UD fibres are aligned with the ASMC flow direction, ply migration takes place. In general, the composite stiffness follows a...

  14. Extraction of lotus fibres from lotus stems under microwave irradiation

    OpenAIRE

    Cheng, Cheng; Guo, Ronghui; Lan, Jianwu; Jiang, Shouxiang

    2017-01-01

    An efficient technology for preparing lotus fibres under microwave irradiation was developed. The lotus fibres were characterized by scanning electron microscopy, Fourier transform infrared spectrometry, X-ray diffraction and thermogravimetry. Lotus fibres prepared are a kind of hollow fibres which are composed of a superfine fibre and an external shell. The effect of the treatment time with hydrogen peroxide under microwave irradiation on components, whiteness, moisture regain, removal rate ...

  15. DESIGN OF COMPOSITION OF CONCRETE USING POLYPROPYLENE FIBRE REINFORCEMENT

    OpenAIRE

    Dang Van Thanh1,*, Vu Hoang Hiep2, Nguyen Van Bac1, Hoang Gia Duong1

    2016-01-01

    Fibre-reinforced concrete is an emerging trend that delivers new materials with high quality for construction. Polyporpylene fibre, an organic textile, has high potential to be used for reinforcing concrete, but there has been little research conducted into using this fibre for concrete reinforcement worldwide and no research work on this fibre reinforced concrete has been published in Vietnam. Thereofore, researchinginto Polyporylene fibre reinforced concrete to establish fundamental underst...

  16. Biological durability and oxidative potential of a stonewool mineral fibre compared to crocidolite asbestos fibres

    Energy Technology Data Exchange (ETDEWEB)

    Hippeli, S. [Lehrstuhl fuer Phytopathologie, Labor fuer Biochemische Toxikologie, Technische Universitaet Muenchen-Weihenstephan, D-85350 Freising-Weihenstephan (Germany); Dornisch, K. [Lehrstuhl fuer Phytopathologie, Labor fuer Biochemische Toxikologie, Technische Universitaet Muenchen-Weihenstephan, D-85350 Freising-Weihenstephan (Germany); Kaiser, S. [Lehrstuhl fuer Phytopathologie, Labor fuer Biochemische Toxikologie, Technische Universitaet Muenchen-Weihenstephan, D-85350 Freising-Weihenstephan (Germany); Draeger, U. [Deutsche Rockwool Mineralwoll GmbH, Karl-Schneider-Strasse 14-18, D-45966 Gladbeck (Germany); Elstner, E.F. [Lehrstuhl fuer Phytopathologie, Labor fuer Biochemische Toxikologie, Technische Universitaet Muenchen-Weihenstephan, D-85350 Freising-Weihenstephan (Germany)

    1997-07-01

    Experiments are described concerning the differences in redox properties and biodurability of natural asbestos fibres and an experimental stonewool fibre incubated in Gamble solution and reconstructed surfactant fluid. Crocidolite exhibits a significantly higher oxidative potential compared to the tested stonewool fibres. The oxidative acitivity of both types of fibres is not constant during incubation over several weeks, but rather shows a sinoidal curve including reactivities much higher than those at the beginning of the incubation. A continuous loss of mass is concluded not to be definitively connected with a continuous loss of toxicity. (orig.). With 1 fig.

  17. ELASTICITY of SHORT FIBRE REINFORCED POLYAMIDE: MORPHOLOGICAL AND NUMERICAl ANALYSIS OF FIBRE ORIENTATION EFFECTS

    Directory of Open Access Journals (Sweden)

    Francesca Cosmi

    2010-10-01

    Full Text Available The fatigue behaviour of injection moulded short fibre reinforced polymers depends upon fibre orientation, as shown in experiments conducted with notched specimens injected through different injection gates. The different fatigue behaviour is mainly related to the different local elastic properties, as determined by the different fibre orientation patterns, resulting into different strain distributions. In order to quantify the relationship between fibre orientation and elastic constants, the Cell Method was applied to volumes extracted from the specimens, reconstructed by micro-tomography.

  18. Shrinkage Behaviour of Fibre Reinforced Concrete with Recycled Tyre Polymer Fibres

    Directory of Open Access Journals (Sweden)

    Marijana Serdar

    2015-01-01

    Full Text Available Different types of fibres are often used in concrete to prevent microcracking due to shrinkage, and polypropylene fibres are among the most often used ones. If not prevented, microcracks can lead to the development of larger cracks as drying shrinkage occurs, enabling penetration of aggressive substances from the environment and reducing durability of concrete structures. The hypothesis of the present research is that polypropylene fibres, used in concrete for controlling formation of microcracks due to shrinkage, can be replaced with recycled polymer fibres obtained from end-of-life tyres. To test the hypothesis, concrete mixtures containing polypropylene fibres and recycled tyre polymer fibres were prepared and tested. Experimental programme focused on autogenous, free, and restrained shrinkage. It was shown that PP fibres can be substituted with higher amount of recycled tyre polymer fibres obtaining concrete with similar shrinkage behaviour. The results indicate promising possibilities of using recycled tyre polymer fibres in concrete products. At the same time, such applications would contribute to solving the problem of waste tyre disposal.

  19. Individual fibre segmentation from 3D X-ray computed tomography for characterising the fibre orientation in unidirectional composite materials

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Jespersen, Kristine Munk; Dahl, Anders Bjorholm

    2017-01-01

    The aim of this paper is to characterise the fibre orientation in unidirectional fibre reinforced polymers, namely glass and carbon fibre composites. The compression strength of the composite is related to the orientation of the fibres. Thus the orientation is essential when designing materials...... for wind turbine blades. The calculation of the fibre orientation distribution is based on segmenting the individual fibres from volumes that have been acquired through X-ray tomography. The segmentation method presented in this study can accurately extract individual fibres from low contrast X-ray scans...... of composites with high fibre volume fraction. From the individual fibre orientations, it is possible to obtain results which are independent of the scanning quality. The compression strength for both composites is estimated from the average fibre orientations and is found to be of the same order of magnitude...

  20. Optical Fibre Pressure Sensors in Medical Applications

    Directory of Open Access Journals (Sweden)

    Sven Poeggel

    2015-07-01

    Full Text Available This article is focused on reviewing the current state-of-the-art of optical fibre pressure sensors for medical applications. Optical fibres have inherent advantages due to their small size, immunity to electromagnetic interferences and their suitability for remote monitoring and multiplexing. The small dimensions of optical fibre-based pressure sensors, together with being lightweight and flexible, mean that they are minimally invasive for many medical applications and, thus, particularly suited to in vivo measurement. This means that the sensor can be placed directly inside a patient, e.g., for urodynamic and cardiovascular assessment. This paper presents an overview of the recent developments in optical fibre-based pressure measurements with particular reference to these application areas.

  1. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Nielsen, Laila

    1997-01-01

    (capillary water uptake) is used, involving an in-situ method and a laboratory method. Three different concrete qualities as well as steel fibres (ZP) and polypropylene fibres (PP) are used. Results of the durability tests on cracked FRC-beams are compared to results for uncracked FRC-beams and beams without......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to il-point bending until a predefined crack width is reached, using a newly developed test setup. As environmental load, exposure to water...... fibres and the influence of fibres and cracks on the water uptake is discussed....

  2. Central Tracking Detector Based on Scintillating Fibres

    CERN Multimedia

    2002-01-01

    Scintillating fibres form a reasonable compromise for central tracking detectors in terms of price, resolution, response time, occupancy and heat production. \\\\ \\\\ New fluorescents with large Stokes shifts have been produced, capable of working without wavelength shifters. Coherent multibundles have been developed to achieve high packing fractions. Small segments of tracker shell have been assembled and beam tests have confirmed expectations on spatial resolution. An opto-electronic delay line has been designed to delay the track patterns and enable coincidences with a first level trigger. Replacement of the conventional phosphor screen anode with a Si pixel chip is achieved. This tube is called ISPA-tube and has already been operated in beam tests with a scintillating fibres tracker. \\\\ \\\\ The aim of the proposal is to improve hit densities for small diameter fibres by increasing the fraction of trapped light, by reducing absorption and reflection losses, by reflecting light at the free fibre end, and by inc...

  3. Interfaces between a fibre and its matrix

    DEFF Research Database (Denmark)

    Lilholt, Hans; Sørensen, Bent F.

    2017-01-01

    parameters (applied load, debond length and relative fibre/matrix displacement) are rather similar for these test modes. A simplified analysis allows the direct determination of the three interface parameters from two plots for the experimental data. The complete analysis is demonstrated for steel fibres...... in polyester matrix. The analysis of existing experimental literature data is demonstrated for steel fibres in epoxy matrix and for tungsten wires in copper matrix. These latter incomplete analyses show that some results can be obtained even if all three experimental parameters are not recorded.......The interface between a fibre and its matrix represents an important element in the characterization and exploitation of composite materials. Both theoretical models and analyses of experimental data have been presented in the literature since modern composite were developed and many experiments...

  4. Shielding properties of fibre cement wallboard.

    Science.gov (United States)

    Thiele, D L; Godwin, G A; Coakley, K S

    1998-09-01

    Transmission data for a fibre cement wallboard (villaboard) are determined for use in diagnostic shielding designs. Villaboard is found to be more attenuating than plasterboard e.g. 9 mm of villaboard is equivalent to 16 mm of plasterboard.

  5. Optical Fibre Pressure Sensors in Medical Applications.

    Science.gov (United States)

    Poeggel, Sven; Tosi, Daniele; Duraibabu, DineshBabu; Leen, Gabriel; McGrath, Deirdre; Lewis, Elfed

    2015-07-15

    This article is focused on reviewing the current state-of-the-art of optical fibre pressure sensors for medical applications. Optical fibres have inherent advantages due to their small size, immunity to electromagnetic interferences and their suitability for remote monitoring and multiplexing. The small dimensions of optical fibre-based pressure sensors, together with being lightweight and flexible, mean that they are minimally invasive for many medical applications and, thus, particularly suited to in vivo measurement. This means that the sensor can be placed directly inside a patient, e.g., for urodynamic and cardiovascular assessment. This paper presents an overview of the recent developments in optical fibre-based pressure measurements with particular reference to these application areas.

  6. Radiation-resistant fibre for particle accelerator

    CERN Multimedia

    2007-01-01

    "Radiation-resistant optical fibre is being used by CERN, the European Laboratory for Particle Physics, in the world's largest particle accelerator, the Large Hadron Collider (LHC) near Geneva." (1 page)

  7. Optical fibres bringing the LHC into focus

    CERN Multimedia

    2003-01-01

    New components are being added to CERN's optical fibre network, which will transport the torrents of data produced by the LHC. 1500 kilometres of cables will be installed in the tunnels and at ground level.

  8. Angiogenic effect induced by mineral fibres

    International Nuclear Information System (INIS)

    Carbonari, Damiano; Campopiano, Antonella; Ramires, Deborah; Strafella, Elisabetta; Staffolani, Sara; Tomasetti, Marco; Curini, Roberta; Valentino, Matteo; Santarelli, Lory; Amati, Monica

    2011-01-01

    Highlights: → In this study we described the angiogenetic effect of some mineral fibres. → Wollastonite fibres induce blood vessel formation. → The size and shape of the fibres were important factors for the cell signalling. → Wollastonite induce ROS-NFκB activation and EGFR signalling. → Involvement of wollastonite exposure in the development of pathological conditions. -- Abstract: Due to the toxic effect of asbestos, other materials with similar chemical-physical characteristics have been introduced to substitute it. We evaluate the angiogenic effect of certain asbestos substitute fibres such as glass fibres (GFs), ceramic fibres (CFs) and wollastonite fibres (WFs) and then compare angiogenic responses to those induced by crocidolite asbestos fibres (AFs). An in vitro model using human endothelial cells in small islands within a culture matrix of fibroblasts (Angio-Kit) was used to evaluate vessel formation. The release of IL-6, sIL-R6, IL-8, VEGF-A and their soluble receptors, sVEGFR-1, sVEGFR-2, was determined in the conditioning medium of Angio-Kit system after fibre treatment. ROS formation and cell viability were evaluated in cultured endothelial cells (HUVEC). To evaluate the involvement of intracellular mechanisms, EGFR signalling, ROS formation and nuclear factor-κB (NFκB) pathway were then inhibited by incubating HUVEC cells with AG1478, NAC and PDTC respectively, and the cytokine and growth factor release was analyzed in the culture medium after 7 days of fibre incubation. Among the mineral fibres tested, WFs markedly induced blood vessel formation which was associated with release of IL-6 and IL-8, VEGF-A and their soluble receptors. ROS production was observed in HUVEC after WFs treatment which was associated with cell cytotoxicity. The EGFR-induced ERK phosphorylation and ROS-mediated NFκB activation were involved in the cytokine and angiogenic factor release. However, only the EGFR activation was able to induce angiogenesis. The WFs

  9. Force focusing in confined fibres and sheets

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Victor; Cerda, Enrique [Departamento de Fisica, Universidad de Santiago, Av. Ecuador 3493, Santiago (Chile); Witten, T A; Liang Tao [James Franck Institute, University of Chicago, Chicago IL 60637 (United States)], E-mail: t-witten@uchicago.edu

    2008-07-07

    A thin fibre or sheet curled into a circular container has a detached region whose shape and force ratios are independent of material properties and container radius. We compute this shape and compare it with experiments. The discrete forces acting at either end of the detached region have a ratio that depends only on the length of the fibre or sheet relative to the circle radius. We calculate this force ratio in three regimes of circle radius. (fast track communication)

  10. Tissue elasticity and the ageing elastic fibre

    OpenAIRE

    Sherratt, Michael J.

    2009-01-01

    The ability of elastic tissues to deform under physiological forces and to subsequently release stored energy to drive passive recoil is vital to the function of many dynamic tissues. Within vertebrates, elastic fibres allow arteries and lungs to expand and contract, thus controlling variations in blood pressure and returning the pulmonary system to a resting state. Elastic fibres are composite structures composed of a cross-linked elastin core and an outer layer of fibrillin microfibrils. Th...

  11. Dynamic response analysis of DFB fibre lasers

    DEFF Research Database (Denmark)

    Yujun, Qian; Varming, Poul; Povlsen, Jørn Hedegaard

    1998-01-01

    We present a model for relative intensity noise (RIN) in DFB fibre lasers which predicts measured characteristics accurately. Calculation results implies that the RIN decreases rapidly with stronger Bragg grating and higher pump power. We propose here a simplified model based on three spatially...... independent rate equations to describe the dynamic response of erbium doped DFB fibre lasers on pump power fluctuations, using coupled-mode theory to calculate the steady-state hole-burning of the erbium ion inversion...

  12. Power consumption in multicore fibre networks

    DEFF Research Database (Denmark)

    Nooruzzaman, Md; Jain, Saurabh; Jung, Yongmin

    2017-01-01

    We study potential energy savings in MCF-based networks compared to SMF-based ones in a Pan-European network topology based on the power consumption of recently fabricated cladding-pumped multi-core optical fibre amplifiers.......We study potential energy savings in MCF-based networks compared to SMF-based ones in a Pan-European network topology based on the power consumption of recently fabricated cladding-pumped multi-core optical fibre amplifiers....

  13. Design of distributed feedback fibre lasers

    DEFF Research Database (Denmark)

    Lauridsen, Vibeke Claudia; Søndergaard, Thomas; Varming, Poul

    1997-01-01

    A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift.......A numerical model for erbium fibre lasers with Bragg gratings is presented. The model is used to optimize the location of a discrete phase-shift and the phase-shift magnitude for a distributed phase-shift....

  14. Polarisation control of DFB fibre lasers

    DEFF Research Database (Denmark)

    Varming, Poul; Philipsen, Jacob Lundgreen; Berendt, Martin Ole

    1998-01-01

    The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser......The polarisation properties of a distributed feedback (DFB) fibre laser are investigated. It is shown experimentally that the birefringence of the UV induced phase-shift is the dominating effect controlling the polarisation properties of the laser...

  15. Design Methods for Fibre Reinforced Concrete

    DEFF Research Database (Denmark)

    Stang, Henrik

    1996-01-01

    The present paper describes the outline of a research project on Fibre Reinforced Concrete (FRC) currently being carried out in Denmark under the supervision of Danish Council of Technology, Danish Technical Research Council and Danish Natural Science Research Counsil.......The present paper describes the outline of a research project on Fibre Reinforced Concrete (FRC) currently being carried out in Denmark under the supervision of Danish Council of Technology, Danish Technical Research Council and Danish Natural Science Research Counsil....

  16. Mode conversion in magneto photonic crystal fibre

    International Nuclear Information System (INIS)

    Otmani, Hamza; Bouchemat, Mohamed; Hocini, Abdesselam; Boumaza, Touraya; Benmerkhi, Ahlem

    2017-01-01

    The first concept of an integrated isolator was based on nonreciprocal TE–TM mode conversion, the nonreciprocal coupling between these modes is caused by the Faraday rotation if the magnetization is aligned along the z–axis, parallel to mode propagation. We propose to study this magneto-optical phenomenon, by the simulation of magneto photonic crystal fibre (MPCF), it consists of a periodic triangular lattice of air-holes filled with magnetic fluid which consists of magnetic nanoparticles into a BIG (Bismuth Iron Garnet) fibre. We simulated the influence of gyrotropy and the wavelength, and calculated Faraday rotation and modal birefringence. In this fibre the light is guided by internal total reflection, like classical fibres. However it was shown that they could function on a mode conversion much stronger than conventional fibres. - Highlights: • We propose to study mode conversion TE–TM, by the simulation of magneto photonic crystal fibre (MPCF). • We simulated the influence of gyrotropy. • We simulated the wavelength. • We calculated Faraday rotation. • We calculated modal birefringence.

  17. The effect of fibre content, fibre size and alkali treatment to Charpy impact resistance of Oil Palm fibre reinforced composite material

    Science.gov (United States)

    Fitri, Muhamad; Mahzan, Shahruddin

    2016-11-01

    In this research, the effect of fibre content, fibre size and alkali treatment to the impact resistance of the composite material have been investigated, The composite material employs oil palm fibre as the reinforcement material whereas the matrix used for the composite materials are polypropylene. The Oil Palm fibres are prepared for two conditions: alkali treated fibres and untreated fibres. The fibre sizes are varied in three sizes: 5mm, 7mm and 10mm. During the composite material preparation, the fibre contents also have been varied into 3 different percentages: 5%, 7% and 10%. The statistical approach is used to optimise the variation of specimen determined by using Taguchi method. The results were analyzed also by the Taguchi method and shows that the Oil Palm fibre content is significantly affect the impact resistance of the polymer matrix composite. However, the fibre size is moderately affecting the impact resistance, whereas the fibre treatment is insignificant to the impact resistance of the oil palm fibre reinforced polymer matrix composite.

  18. Fibre-matrix interface properties in a wood fibre reinforced cement matrix

    NARCIS (Netherlands)

    Sierra Beltran, M.G.; Schlangen, H.E.J.G.

    2010-01-01

    Wood fibres can be a low cost reinforcement for cementitious materials for structural applications. In order to design a ductile cementitious material reinforced with softwood fibres the fibrematrix interface properties are studied. Pullout tests have been carried out to determine the bond strength

  19. Analysis of filler--fibre interaction in fly ash filled short fibre-epoxy ...

    Indian Academy of Sciences (India)

    These properties showed an improvement of about 30-40% as compared to the ones where a single reinforcement either ash or fibre was used. Further, they exhibited uniform distribution of defects whose population was least compared to the situation where only one component (either filler or fibre) as reinforcement was ...

  20. EVALUATION OF FIBRE LENGTH DISTRIBUTION IN A SHORT GLASS FIBRE REINFORCED PA-6

    Directory of Open Access Journals (Sweden)

    Camilla Ravalico

    2015-09-01

    Full Text Available The aim of this work is to evaluate the fibre length distribution in a polyamide reinforced by short glass fibre. The fibre length and the fibre orientation distributions strongly influence the mechanical properties of short fibre reinforced composites. The sample investigated is a 30GFPA6 (polyamide-6 reinforced by 30 % by weight glass fibre, extracted from an injection-moulded plate. The digital reconstruction of the three-dimensional structure of the sample was obtained by synchrotron radiation micro-computed tomography (micro-CT, a high spatial resolution non-destructive technique. One global and one local method have been tested for the automatic evaluation of the fibre length distribution in our sample. The global method is based on the mean fibre length distribution computed from the Star Length Distribution (SLD, a morphological parameter. The local method is based on a 3D skeletonize function. The results are discussed in the light of the experimental data available in literature.

  1. Properties of Wood Fibre-Polypropylene Composites: Effect of Wood Fibre Source

    Science.gov (United States)

    Butylina, Svetlana; Martikka, Ossi; Kärki, Timo

    2011-04-01

    This study examined the effect of type of wood fibre source on the physical and mechanical properties of wood fibre-polypropylene composites. Wood flour, fibres of heat-treated wood and pellets were used as sources of wood fibres in the manufacturing process. All studied wood fibre-polypropylene composites were made from 75% wood, 22% recycled polypropylene (PP) and 3% maleated polypropylene (MAPP). Wood fibre-polypropylene composites were compounded in a conical twin-screw extruder. Water absorption and thickness swelling were studied. Mechanical properties of the composites were characterised by tensile, flexural, and impact testing. Micromechanical deformation processes were investigated using scanning electron microscopy done on the fractured surfaces of broken samples. The durability of composites exposed to three accelerated cycles of water immersion, freezing and thawing was examined. The results showed that the density of the composites was a key factor governing water absorption and thickness swelling. A significant improvement in tensile strength, flexural strength, and Charpy impact strength was observed for composites reinforced with heat-treated fibre compared to composites reinforced with pellets and especially to wood flour reinforced composites. The flexural strength and dimensional stability performance reduced after exposure to freeze-thaw cycling for all composites, but the degree of these changes was dependent on the wood fibre source.

  2. Vibrated and self-compacting fibre reinforced concrete: experimental investigation on the fibre orientation

    Science.gov (United States)

    Conforti, A.; Plizzari, G. A.; Zerbino, R.

    2017-09-01

    In addition to the fibre type and content, the residual properties of fibre reinforced concrete are influenced by fibre orientation. Consequently, the performance fibre reinforced concrete can be affected by its fresh properties (workability, flowing capacity) and by casting and compaction processes adopted. This paper focuses on the study of the orientation of steel or macro-synthetic fibres in two materials characterized by very different fresh properties: vibrated and self-compacting concrete. Four rectangular slabs 1800 mm long, 925 mm wide and 100 mm high were produced changing concrete and fibre type. From each slab, eighteen small prisms (550 mm long) were firstly cut either orthogonal or parallel to casting direction and, secondly, notched and tested in bending according to EN 14651. Experimental results showed that the toughness properties of a thin slab significantly varies both in vibrated and self-compacting concrete, even if in case of self-compacting concrete this variation resulted higher. Steel fibres led to greater variability of results compared to polymer one, underlining a different fibre orientation. A discussion on the relative residual capacity measured on the prisms sawn from the slabs and the parameters obtained from standard specimens is performed.

  3. Fibre-Bragg-grating writing in single-mode optical fibres by UV femtosecond pulses

    International Nuclear Information System (INIS)

    Zagorul'ko, K A; Kryukov, P G; Dianov, Evgenii M; Dragomir, A; Nikogosyan, D N

    2003-01-01

    Fibre-Bragg-grating writing in single-mode optical fibres by the phase-mask method using 220-fs, 264-nm UV pulses of intensity 31 - 77 GW cm -2 is reported for the first time. The achieved degree of modulation of the photoinduced refractive index was 1.9 x 10 -3 in an H 2 -loaded SMF-28 telecommunication fibre and 1.1 x 10 -3 in a H 2 -free Nufern GF1 fibre. The dependence of the induced refractive index on the intensity for the same irradiation fluences in the case of the H 2 -loaded SMF-28 fibre shows that the refractive index is induced due to nonlinear absorption. (letters)

  4. Polarisation maintaining fibre with pure silica core and two depressed claddings for fibre optic gyroscope

    Science.gov (United States)

    Kurbatov, A. M.; Kurbatov, R. A.; Voloshin, V. V.; Vorob'ev, I. L.; Kolosovsky, A. O.

    2016-12-01

    Polarisation maintaining (PM) fibre is described with pure silica core and two depressed claddings for fibre optic gyro (FOG) sensing coil. Detailed mathematical simulation is presented by supermodes method, which is extremely necessary for such fibre. Simulation is fulfilled by frequency domain finite difference method (FDFDM), taking into account all details of realistic index profile with stress applying parts, while the leakage/bend loss occur in the region with complex index, surrounding the fibre. Cutoff and small bend loss are theoretically predicted and experimentally measured with excellent agreement between theory and experiment. Polarisation maintaining ability is measured in the form of conventional h-parameter (7.1·10-6 1/m) for 90-μm diameter fibre with birefringence value only 3.9·10-4.

  5. Influence of fibre design and curvature on crosstalk in multi-core fibre

    Energy Technology Data Exchange (ETDEWEB)

    Egorova, O N; Astapovich, M S; Semjonov, S L; Dianov, E M [Fiber Optics Research Center, Russian Academy of Sciences, Moscow (Russian Federation); Melnikov, L A [Kotel' nikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, Saratov Branch, Saratov (Russian Federation); Salganskii, M Yu [G.G.Devyatykh Institute of Chemistry of High-Purity Substances, Russian Academy of Sciences, Nizhnii Novgorod (Russian Federation); Mishkin, S N; Nishchev, K N [N.P. Ogarev Mordovia State University, Physics and Chemistry Institute, Saransk (Russian Federation)

    2016-03-31

    We have studied the influence of cross-sectional structure and bends on optical cross-talk in a multicore fibre. A reduced refractive index layer produced between the cores of such fibre with a small centre-to-centre spacing between neighbouring cores (27 μm) reduces optical cross-talk by 20 dB. The cross-talk level achieved, 30 dB per kilometre of the length of the multicore fibre, is acceptable for a number of applications where relatively small lengths of fibre are needed. Moreover, a significant decrease in optical cross-talk has been ensured by reducing the winding diameter of multicore fibres with identical cores. (fiber optics)

  6. Hemp fibres: Enzymatic effect of microbial processing on fibre bundle structure

    DEFF Research Database (Denmark)

    Thygesen, Anders; Liu, Ming; Meyer, Anne S.

    2013-01-01

    The effects of microbial pretreatment on hemp fibres were evaluated after microbial retting using the white rot fungi Ceriporiopsis subvermispora and Phlebia radiata Cel 26 and water retting. Based on chemical composition, P. radiata Cel 26 showed the highest selectivity for pectin and lignin...... degradation and lowest cellulose loss (14%) resulting in the highest cellulose content (78.4%) for the treated hemp fibres. The pectin and lignin removal after treatment with P. radiata Cel 26 were of the order 82% and 50%, respectively. Aligned epoxy-matrix composites were made from hemp fibres defibrated...... hemp fibres were badly impregnated due to porosity caused by surface impurities such as epidermis and other pectin rich plant cells. The pectin and lignin mainly located in the outer part of the fibres were assumed to be extracted and degraded by pectinase and peroxidase enzymes produced by the fungi....

  7. Latest developments in silica fibre luminescence dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, D. A.; Abdul S, S. F.; Jafari, S. M.; Alanazi, A. [University of Surrey, Department of Physics, GU2 7XH Guildford, Surrey (United Kingdom); Amouzad M, G. [University of Malaya, Faculty of Engineering, Department of Electrical Engineering, Integrated Lightwave Research Group, 50603 Kuala Lumpur (Malaysia); Addul R, H. A.; Mizanur R, A. K. M.; Zubair, H. T.; Begum, M.; Yusoff, Z.; Omar, N. Y. M. [Multimedia University, Faculty of Engineering, 2010 Cyberjaya, Selangor (Malaysia); Maah, M. J. [University of Malaya, Department of Chemistry, 50603 Kuala Lumpur (Malaysia); Collin, S. [National Physical Laboratory, Hampton Road, Teddington, TW11 OLW Middlesex (United Kingdom); Mat-Sharif, K. A.; Muhd-Yassin, S. Z.; Zulkifli, M. I., E-mail: d.a.bradley@surrey.ac.uk [Telekom Malaysia Research and Development Sdn Bhd., 63000 Cyberjaya, Selangor (Malaysia)

    2015-10-15

    Full text: Using tailor made sub-mm diameter doped-silica fibres, we are carrying out luminescence dosimetry studies for a range of situations, including thermoluminescence (Tl)investigations on a liquid alpha source formed of {sup 223}RaCl (the basis of the Bayer Health care product Xofigo), the Tl response to a 62 MeV proton source and Tl response to irradiation from an {sup 241}Am-Be neutron source. In regard to the former, in accord with the intrinsic high linear energy transfer (Let) and short path length (<100 um) of the α-particles in calcified tissue, the product is in part intended as a bone-seeking radionuclide for treatment of metastatic cancer, offering high specificity and efficacy. The Tl yield of Ge-doped SiO{sub 2} fibres has been investigated including for photonic crystal fibre un collapsed, flat fibres and single mode fibres, these systems offering many advantages over conventional passive dosimetry types. In particular, one can mention comparable and even superior sensitivity, an effective atomic number Z{sub eff} of the silica dosimetric material close to that of bone, and the glassy nature of the fibres offering the additional advantage of being able to place such dosimeters directly into liquid environments. Finally we review the use of our tailor made fibres for on-line radioluminescence measurements of radiotherapy beams. The outcome from these various lines of research is expected to inform development of doped fiber radiation dosimeters of versatile utility, ranging from clinical applications through to industrial studies and environmental evaluations. (Author)

  8. Experimental and numerical study on refractive index sensors based on fibre Bragg gratings inscribed in multimode fibre

    Science.gov (United States)

    Filipe Kuhne, Jean; Rocha, Ana Maria; de Oliveira, Valmir; José Kalinowski, Hypolito; Canute Kamikawachi, Ricardo

    2018-02-01

    In this work is reported the experimental and numerical results of the refractive index response of etched fibre Bragg gratings written in a graded index multimode fibre. The responses of the modes coupled by the grating inscribed in a multimode fibre are compared with the mode coupled by a grating inscribed in single mode fibre. The results of this study show that the refractive index sensitivity and the dynamical range of etched fibre Bragg gratings written in multimode fibres are higher than the ones verified in single-mode fibres. The determination of oil-biodiesel blend concentrations are also compared as an example of practical applications. It is shown that a greater core diameter of the multimode fibre enables the Bragg gratings to exhibit enhanced sensitivity without requiring further fibre diameter reduction.

  9. Microanalytical investigation of fibre-reinforced ceramic materials

    International Nuclear Information System (INIS)

    Meier, B.; Grathwohl, G.

    1989-01-01

    Microanalytical investigations have been made on samples of ceramic fibres (SiC fibres, (Nicalon) C fibre coated with TiN) and fibre-reinforced ceramics (SiC-and glass-matrices). High resolution Auger electron spectroscopy (HRAES), electron probe microanalysis (EPMA) and scanning electron microscopy were employed for these examinations. Analysis was best performed with HRAES on account of its lateral and depth resolution. Some of the problems involved in this technique are discussed e.g. electron beam effects. AES depth profiles of ceramic fibres are reported and compared with the surface analysis of fibres in the composites after being broken in situ. (orig.)

  10. Functional dependency between the logistics security system and the MySAP ERP in metallurgy

    Directory of Open Access Journals (Sweden)

    P. Ranitović

    2013-10-01

    Full Text Available MySAP ERP - Enterprise Resource Planning (system - solution which provides a whole set of functions for the business analytics, finance, human resources management, logistics and corporate services has developed from SAP R/3. It is one of the main products of the SAP AG German multinational company and as such, it is a very important element of the international industrial and technological security system. By defining the functional dependency between the security systems (logistics security systems and the IT (My SAP ERP systems in metallurgy, a concept for designing MY SAP ERP system in metallurgic industry is defined, based on the security aspects.

  11. Physical metallurgy: Scientific school of the Academician V.M. Schastlivtsev

    Science.gov (United States)

    Tabatchikova, T. I.

    2016-04-01

    This paper is to honor Academician Vadim Mikhailovich Schastlivtsev, a prominent scientist in the field of metal physics and materials science. The article comprises an analysis of the topical issues of the physical metallurgy of the early 21st century and of the contribution of V.M. Schastlivtsev and of his school to the science of phase and structural transformations in steels. In 2015, Vadim Mikhailovich celebrates his 80th birthday, and this paper is timed to this honorable date. The list of his main publications is given in it.

  12. Metallurgy of mercury in Almaden: from aludel furnaces until Pacific furnaces

    International Nuclear Information System (INIS)

    Tejero-Manzanares, J.; Garrido Saenz, I.; Mata Cabrera, F.; Rubio Mesas, M. L.

    2014-01-01

    This paper shows the different types of furnaces for roasting cinnabar, used in the metallurgy of quicksilver over the centuries of exploitation of the Almaden Mines (Spain). Some of these techniques are part of our industrial heritage. They have contributed to name UNESCO World Heritage Site the vast technological legacy of these mines recently. This research contributes to close the long way of metallurgical activity from aludel furnaces until Pacif furnaces, first and lasted technology to produce on an industrial scale. It is delved into the most relevant aspects having to do with the type, evolution and number of furnaces existing on each of the periods. (Author)

  13. Proceedings of the III International Congress of Mining and Metallurgy MINEMETAL 2016

    International Nuclear Information System (INIS)

    2016-10-01

    The III International Congress of Mining and Metallurgy was inaugurated at the Plaza América Convention Center in Varadero. Professionals from 16 countries come together to promote scientific exchange for sustainable mining and to make concrete future investments to boost the development of this important sector in Cuba. Among the topics that will occupy the agenda of these days of congress stand out the development of geology, new technological processes, advances in the application of zeolite, sustainable development and care of the environment.

  14. Accelerated Near-Threshold Fatigue Crack Growth Behavior of an Aluminum Powder Metallurgy Alloy

    Science.gov (United States)

    Piascik, Robert S.; Newman, John A.

    2002-01-01

    Fatigue crack growth (FCG) research conducted in the near threshold regime has identified a room temperature creep crack growth damage mechanism for a fine grain powder metallurgy (PM) aluminum alloy (8009). At very low DK, an abrupt acceleration in room temperature FCG rate occurs at high stress ratio (R = Kmin/Kmax). The near threshold accelerated FCG rates are exacerbated by increased levels of Kmax (Kmax less than 0.4 KIC). Detailed fractographic analysis correlates accelerated FCG with the formation of crack-tip process zone micro-void damage. Experimental results show that the near threshold and Kmax influenced accelerated crack growth is time and temperature dependent.

  15. Influence of the Testing Gage Length on the Strength, Young's Modulus and Weibull Modulus of Carbon Fibres and Glass Fibres

    Directory of Open Access Journals (Sweden)

    Luiz Claudio Pardini

    2002-10-01

    Full Text Available Carbon fibres and glass fibres are reinforcements for advanced composites and the fiber strength is the most influential factor on the strength of the composites. They are essentially brittle and fail with very little reduction in cross section. Composites made with these fibres are characterized by a high strength/density ratio and their properties are intrisically related to their microstructure, i.e., amount and orientation of the fibres, surface treatment, among other factors. Processing parameters have an important role in the fibre mechanical behaviour (strength and modulus. Cracks, voids and impurities in the case of glass fibres and fibrillar misalignments in the case of carbon fibres are created during processing. Such inhomogeneities give rise to an appreciable scatter in properties. The most used statistical tool that deals with this characteristic variability in properties is the Weibull distribution. The present work investigates the influence of the testing gage length on the strength, Young's modulus and Weibull modulus of carbon fibres and glass fibres. The Young's modulus is calculated by two methods: (i ASTM D 3379M, and (ii interaction between testing equipment/specimen The first method resulted in a Young modulus of 183 GPa for carbon fibre, and 76 GPa for glass fibre. The second method gave a Young modulus of 250 GPa for carbon fibre and 50 GPa for glass fibre. These differences revelead differences on how the interaction specimen/testing machine can interfere in the Young modulus calculations. Weibull modulus can be a tool to evaluate the fibre's homogeneity in terms of properties and it is a good quality control parameter during processing. In the range of specimen gage length tested the Weibull modulus for carbon fibre is ~ 3.30 and for glass fibres is ~ 5.65, which indicates that for the batch of fibres tested, the glass fibre is more uniform in properties.

  16. Tissue elasticity and the ageing elastic fibre.

    Science.gov (United States)

    Sherratt, Michael J

    2009-12-01

    The ability of elastic tissues to deform under physiological forces and to subsequently release stored energy to drive passive recoil is vital to the function of many dynamic tissues. Within vertebrates, elastic fibres allow arteries and lungs to expand and contract, thus controlling variations in blood pressure and returning the pulmonary system to a resting state. Elastic fibres are composite structures composed of a cross-linked elastin core and an outer layer of fibrillin microfibrils. These two components perform distinct roles; elastin stores energy and drives passive recoil, whilst fibrillin microfibrils direct elastogenesis, mediate cell signalling, maintain tissue homeostasis via TGFβ sequestration and potentially act to reinforce the elastic fibre. In many tissues reduced elasticity, as a result of compromised elastic fibre function, becomes increasingly prevalent with age and contributes significantly to the burden of human morbidity and mortality. This review considers how the unique molecular structure, tissue distribution and longevity of elastic fibres pre-disposes these abundant extracellular matrix structures to the accumulation of damage in ageing dermal, pulmonary and vascular tissues. As compromised elasticity is a common feature of ageing dynamic tissues, the development of strategies to prevent, limit or reverse this loss of function will play a key role in reducing age-related morbidity and mortality.

  17. Nanoporous ultrahigh specific surface polyacrylonitrile fibres

    International Nuclear Information System (INIS)

    Zhang Lifeng; Hsieh, Y-L

    2006-01-01

    The concept of phase separation was coupled with electrospinning to generate polyacrylonitrile (PAN) and poly(ethylene oxide) (PEO) bicomponent fibres that, upon removal of the phase-separated PEO domains, became nanoporous. Electrospinning of PAN (150 kDa) with 15-50% w/w PEO (10 kDa) at a 8% w/w total concentration in N,N-dimethylformamide produced fibres with decreasing averaged diameters from 390 to 130 nm. Evidence of phase separation between PAN and PEO in the bicomponent fibres was indicated by the characteristic PAN and PEO peaks by Fourier transform infrared (FTIR) spectroscopy and solid-state nuclear magnetic resonance (NMR) imaging, and confirmed by the co-existence of PAN cyclization and PEO melting by differential scanning calorimetry (DSC) and the presence of PEO crystalline diffraction by wide-angle x-ray scattering (WAXS). Removal of PEO by dissolution in water was confirmed by the matched mass loss to PEO fraction and the absence of PEO by FTIR and DSC. The water-treated bicomponent fibres appeared slightly larger in diameter and contained internal pores of nanometre scale. The nanoporous fibres generated from 50/50 PAN/PEO bicomponent precursor contained internal pores of a few nanometres to tens of nanometres in size and had 50% higher pore volume and 2.5-fold higher specific surface

  18. Fibre-reinforced hydrogels for tissue engineering

    Science.gov (United States)

    Waters, Sarah; Byrne, Helen; Chen, Mike; Dias Castilho, Miguel; Kimpton, Laura; Please, Colin; Whiteley, Jonathan

    2017-11-01

    Tissue engineers aim to grow replacement tissues in vitro to replace those in the body that have been damaged through age, trauma or disease. One approach is to seed cells within a scaffold consisting of an interconnected 3D-printed lattice of polymer fibres, cast in a hydrogel, and subject the construct (cell-seeded scaffold) to an applied load in a bioreactor. A key question is to understand how this applied load is distributed throughout the construct to the mechanosensitive cells. To address this, we exploit the disparate length scales (small inter-fibre spacing compared with construct dimensions). The fibres are treated as a linear elastic material and the hydrogel as a poroelastic material. We employ homogenisation theory to derive equations governing the material properties of a periodic, elastic-poroelastic composite. To validate the mobel, model solutions are compared to experimental data describing the unconfined compression of the fibre-reinforced hydrogels. The model is used to derive the bulk mechanical properties of a cylindrical construct of the composite material for a range of fibre spacings, and the local mechanical environment experienced by cells embedded within the construct is determined. Funded by the European Union Seventh Framework Programme (FP7/2007-2013).

  19. Fibre-Related Dietary Patterns: Socioeconomic Barriers to Adequate Fibre Intake in Polish Adolescents. A Short Report.

    Science.gov (United States)

    Krusinska, Beata; Kowalkowska, Joanna; Wadolowska, Lidia; Wuenstel, Justyna Weronika; Slowinska, Malgorzata Anna; Niedzwiedzka, Ewa

    2017-06-10

    There is no complete explanation for the association between socioeconomic status (SES), fibre, and whole diet described by dietary patterns. The aim of this short report was to increase the understanding of adolescent dietary patterns related to fibre in their social context. A cross-sectional study was conducted involving 1176 adolescents aged 13-18 years from central and north-eastern Poland. The overall SES was composed of five single factors: place of residence, self-declared economic situation of family, self-declared economic situation of household, paternal and maternal education. The consumption frequency of nine dietary fibre sources was collected using Block's questionnaire and was expressed in points. Fibre dietary patterns (DPs) were drawn by cluster analysis and odds ratios (ORs) adjusted for age, sex, and BMI were calculated. Three fibre-related DPs were identified: "High-fibre" (mean frequency of total fibre intake 22.7 points; range: 0-36), "Average-fibre" (17.7 points), "Low-fibre" (14.6 points). The "High-fibre" DP was characterized by a relatively higher frequency consumption of white bread, fruit, fruit or vegetable juices, potatoes, green salad and prepared vegetables, and a moderate frequency consumption of high-fibre or bran cereals and wholegrain bread compared to the "Low-fibre" DP. The "Average-fibre" DP was characterized by a relatively higher frequency consumption of wholegrain bread and high-fibre or bran cereals and a moderate frequency consumption of fruit, fruit or vegetable juices, green salad and prepared vegetables compared to the "Low-fibre" DP. Less likely to adhere to the "High-fibre" DP were adolescents with low SES (OR: 0.55, 95% CI: 0.39-0.77) or average SES (0.58, 95% CI: 0.41-0.81) in comparison with high SES (reference) as a result of elementary or secondary paternal or maternal education, rural residence, and lower household economic situation. Similar associations were found for the "Average-fibre" DP. Low and average

  20. Fibre Length Reduction in Natural Fibre-Reinforced Polymers during Compounding and Injection Moulding—Experiments Versus Numerical Prediction of Fibre Breakage

    Directory of Open Access Journals (Sweden)

    Katharina Albrecht

    2018-03-01

    Full Text Available To establish injection-moulded, natural fibre-reinforced polymers in the automotive industry, numerical simulations are important. To include the breakage behaviour of natural fibres in simulations, a profound understanding is necessary. In this study, the length and width reduction of flax and sisal fibre bundles were analysed experimentally during compounding and injection moulding. Further an optical analysis of the fibre breakage behaviour was performed via scanning electron microscopy and during fibre tensile testing with an ultra-high-speed camera. The fibre breakage of flax and sisal during injection moulding was modelled using a micromechanical model. The experimental and simulative results consistently show that during injection moulding the fibre length is not reduced further; the fibre length was already significantly reduced during compounding. For the mechanical properties of a fibre-reinforced composite it is important to overachieve the critical fibre length in the injection moulded component. The micromechanical model could be used to predict the necessary fibre length in the granules.

  1. Mechanical Property Analysis on Sandwich Structured Hybrid Composite Made from Natural Fibre, Glass Fibre and Ceramic Fibre Wool Reinforced with Epoxy Resin

    Science.gov (United States)

    Bharat, K. R.; Abhishek, S.; Palanikumar, K.

    2017-06-01

    Natural fibre composites find wide range of applications and usage in the automobile and manufacturing industries. They find lack in desired properties, which are required for present applications. In current scenario, many developments in composite materials involve the synthesis of Hybrid composite materials to overcome some of the lacking properties. In this present investigation, two sandwich structured hybrid composite materials have been made by reinforcing Aloe Vera-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and Sisal fibre-Ceramic Fibre Wool-Glass fibre with Epoxy resin matrix and its mechanical properties such as Tensile, Flexural and Impact are tested and analyzed. The test results from the two samples are compared and the results show that sisal fibre reinforced hybrid composite has better mechanical properties than aloe vera reinforced hybrid composite.

  2. Study on the formation of cubic texture in Ni-7 at.% W alloy substrates by powder metallurgy routes

    DEFF Research Database (Denmark)

    Zhao, Yue; Suo, HongLi; Zhu, YongHua

    2009-01-01

    One of the main challenges for coated conductor applications is to produce sharp cubic textured alloy substrates with high strength and low magnetism. In this work, the cubic textured Ni–7 at.% W substrates were prepared from different powder metallurgy ingots by rolling-assisted biaxially textured...... substrate processing. The fabrication processes of cubic texture in the Ni–7 at.% W tapes by two powder metallurgy routes are described in detail. Through the optimized process, full width at half maximum values of 6.7° and 5.0° were obtained, as estimated by X-ray (1 1 1) phi scan and (2 0 0) rocking curve...

  3. THERMOMECHANICAL PROPERTIES OF JUTE/BAGASSE HYBRID FIBRE REINFORCED EPOXY THERMOSET COMPOSITES

    OpenAIRE

    Sudhir Kumar Saw; Chandan Datta

    2009-01-01

    Natural fibres are partly replacing currently used synthetic fibres as reinforcement for polymer composites. Jute fibre bundles were high-cellulose-content modified by alkali treatment, while the bagasse fibre bundles were modified by creating quinones in the lignin portions of fibre surfaces and reacting them with furfuryl alcohol (FA) to increase their adhesiveness. The effects of different fibre bundle loading and modification of bagasse fibre surfaces in hybrid fibre reinforced epoxy comp...

  4. EDITORIAL: Optical Fibre Sensors 18 (OFS-18)

    Science.gov (United States)

    Jones, Julian D. C.; Tatam, Ralph P.

    2007-10-01

    The International Conference on Optical Fibre Sensors (OFS-18) was held in October 2006 in Cancún, Mexico, under the general chairmanship of Dr Alexis Mendez (MCH Engineering LLC, USA) and Dr Fernando Mendoza (Centro de Investigaciones en Optica, Mexico). 'OFS', as it has become known, is firmly established as the leading international conference for the optical fibre sensor community. Since its inception, in London in 1983, and under the leadership of an international steering committee independent of any learned society or professional institution, it has been held approximately every eighteen months. The venue nominally rotates from Europe, to the Americas, and thence to Asia and the Pacific. OFS-18 demonstrated the continuing vigour of the community, with some 250 papers presented, plus two workshops, with attendance as international as ever. In recent years, it has become a tradition to publish a post-conference special issue in the journal Measurement Science and Technology, and these special issues offer a representative sample of the current status of the field. In the nearly 25 years since OFS began, many of the early ideas and laboratory-based proof-of-principle experiments have led to highly developed instrumentation systems, and to successful commercial products. Perhaps the most mature of all of these technologies is the optical fibre gyroscope, with the fibre hydrophone a close second—originally developed for defence applications for which it is now established, but with increasing relevance to the oil and gas industry; electromagnetic sensors based on the Faraday and electro-optic effects are of growing significance in the power generation and distribution industry; whilst in-fibre grating-based sensors occupy an expanding niche in structural monitoring, especially in civil engineering. It is therefore appropriate that the first day of OFS was devoted to workshops on structural health monitoring, and to commemorate the 30th anniversary of the

  5. Single fibre strength of cellulosic fibre extracted from "Belatlan roots" plant

    Science.gov (United States)

    M. Hanis. A., H.; Majid, M. S. Abdul; Ridzuan, M. J. M.; Fahmi, I.

    2017-12-01

    The tensile strength of a fibre extracted from "Belatlan Root" plant was investigated as potential reinforcement material in polymeric composites. Following retting process, the fibres were manually extracted from "Belatlan" root's plant. The fibres were treated with 5 % 10 %, 15 %, and 20 % sodium hydroxide (NaOH) wt. % concentration for 24 h. The single fibre tests were then performed in accordance with ASTM D3822-07 standard. The surfaces of the fibres prior and after the treatment were observed with a metallurgical Microscope MT8100 and the physical properties were recorded. Physically, in the post treatment, the fibre showed a decrease in diameter with increase in NaOH concentration The results from the mechanical testing indicates that samples subjected to 5 % NaOH treatment yielded the highest tensile strength and elastic modulus at 89.05 MPa ± 2.75 and 3.81 GPa ± 0.09 respectively compared to untreated fibres. This represents an increase of almost 72 % in tensile strength and 42 % for elastic modulus. The findings support the preliminary information for incorporating the "Belatlan Root" as possible reinforcing materials in composite structures.

  6. Fatigue processes in thermoplastic fibres; Les mecanismes de fatigue dans les fibres thermoplastiques

    Energy Technology Data Exchange (ETDEWEB)

    Herrera Ramirez, J.M.

    2004-09-15

    The present study examines and compares the behaviour of the two types of PA66 fibres and two types of PET fibres under fatigue loading up to failure, and the correlation between the fibres (nano)structures and their structural heterogeneities, with fatigue lifetimes. Several techniques have been used to analyze the materials, such as scanning electron microscopy (SEM), microanalysis (EDS), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and micro-Raman spectroscopy. A meticulous analysis by scanning electron microscopy of the fracture morphology of fibres broken in tension and in fatigue, as well as a study of the fatigue life, were undertaken. The fatigue process occurs when the cyclic load amplitude is sufficiently large, however a condition for fatigue failure is that the minimum load each cycle must be lower than a threshold stress level. Failure under fatigue conditions leads to distinctive fracture morphologies which are very different from those seen after tensile or creep failure and this allows easy identification of the fatigue process. The fibres have been analyzed in the as received state and after fatigue failure in order to observe the microstructural changes resulting from the fatigue loading. The results will be compared with those obtained for fibres loaded under conditions where the fatigue process was hindered. The role of the microstructure of the fibres in determining fatigue will be discussed in this work and the possibility of improving their resistance to fatigue or eliminating the fatigue process will be discussed. (author)

  7. Biomolecular analysis of elastic fibre molecules.

    Science.gov (United States)

    Cain, Stuart A; Raynal, Bertrand; Hodson, Nigel; Shuttleworth, Adrian; Kielty, Cay M

    2008-05-01

    Elastic fibres are macromolecular extracellular matrix assemblies that endow dynamic connective tissues such as arteries, lungs and skin with the property of elastic recoil. Here, we describe how we have purified elastic fibre molecules and then analysed them using a range of biochemical and biomolecular approaches. Such approaches have provided powerful insights into the complex hierarchical processes of extracellular matrix assembly. We outline molecular interaction and kinetics assays using Biacore, biophysical approaches such as multi-angle laser light scattering and analytical ultracentrifugation which provide information on molecular and macromolecular shape and mass in solution, the visualisation of molecules and assemblies using microscopy approaches such as atomic force microscopy and environmental scanning electron microscopy, and compositional analysis of macromolecular complexes using mass spectrometry. Data from these in vitro analytical approaches can be combined to develop powerful new models of elastic fibre assembly.

  8. Laser acceleration... now with added fibre

    CERN Multimedia

    Katarina Anthony

    2012-01-01

    Laser acceleration technology is plagued by two main issues: efficiency and repetition rates. In other words, lasers consume too much power and cannot sustain accelerating particles long enough to produce collisions. ICAN, a new EU-funded project, is examining how fibre lasers may help physicists tackle these issues.   A diode-pumped fibre laser. (Image courtesy of Laser Zentrum Hannover.) The International Coherent Amplification Network (ICAN) is studying the potential of lasers for collision physics. CERN is a beneficiary of the project and will collaborate with 15 other institutes from around the world, including KEK in Japan, Fermilab in the USA, and DESY in Germany. “The network is looking into existing fibre laser technology, which we believe has fantastic potential for accelerators,” says Gerard Mourou, ICAN co-ordinator at the École Polytechnique in France. “The hope is to make laser acceleration competitive with traditional radio-fre...

  9. Mechanical losses in thin fused silica fibres

    International Nuclear Information System (INIS)

    Bilenko, I A; Braginsky, V B; Lourie, S L

    2004-01-01

    Intracavity topology of the readout system for LIGO III project and table-top QND mechanical measurements under development require the use of small probe masses and suspensions with a very low level of internal losses. A good choice is to use thin fused silica fibres similar to LIGO II mirrors suspensions. Mechanical losses of silica fibres are investigated in this work through the study of quality factor dependence on diameter for pendulum and violin modes of oscillations with diameters ranging from 1.5 to 40 μm. The estimated values of effective mechanical loss angle show noticeably greater growth with lower diameters than might be expected while extrapolating known results of research done for thicker fibres

  10. Mechanical losses in thin fused silica fibres

    Energy Technology Data Exchange (ETDEWEB)

    Bilenko, I A; Braginsky, V B; Lourie, S L [Department of Oscillatory Physics, Physics Faculty, Moscow State University (Russian Federation)

    2004-03-07

    Intracavity topology of the readout system for LIGO III project and table-top QND mechanical measurements under development require the use of small probe masses and suspensions with a very low level of internal losses. A good choice is to use thin fused silica fibres similar to LIGO II mirrors suspensions. Mechanical losses of silica fibres are investigated in this work through the study of quality factor dependence on diameter for pendulum and violin modes of oscillations with diameters ranging from 1.5 to 40 {mu}m. The estimated values of effective mechanical loss angle show noticeably greater growth with lower diameters than might be expected while extrapolating known results of research done for thicker fibres.

  11. Analysing the nanoporous structure of aramid fibres

    DEFF Research Database (Denmark)

    Pauw, Brian Richard; Vigild, Martin Etchells; Mortensen, Kell

    2010-01-01

    After consideration of the applicability of classical methods, a novel analysis method for the characterization of fibre void structures is presented, capable of fitting the entire anisotropic two-dimensional scattering pattern to a model of perfectly aligned, polydisperse ellipsoids. It is tested...... for validity against the computed scattering pattern for a simulated nanostructure, after which it is used to fit the scattering from the void structure of commercially available heat-treated poly(p-phenylene terephtalamide) fibre and its as-spun precursor fibre. The application shows a reasonable fit...... and results in size distributions for both the lengths and the widths of the ellipsoidal voids. Improvements to the analysis methods are compared, consisting of the introduction of an orientation distribution for the nano-ellipsoids, and the addition of large scatterers to account for the effect of fibrillar...

  12. Infrared Supercontinuum Generation in Optical Fibres

    DEFF Research Database (Denmark)

    Dupont, Sune Vestergaard Lund

    During my PhD studies I have worked with intense lasers and optical fibres. In our conceptual universe the colour of light (wavelength) does not depend on the material in which it propagates. At high intensities however, nonlinear effects change the behaviour of light and rise of new wavelength...... with laser-like intensity is obtained, which otherwise is impossible without the use of more complicated equipment. Until recently, supercontinuum covering the mid-infrared was not possible due to absorption in the silica glass optical fibres are made of. In our project infrared transparent materials...... such as ZBLAN and chalcogenide have been investigated. Using ZBLAN it has been possible to generated a supercontinuum stretching beyond 4200 nm. Supercontinuum generation requires knowledge about the physical properties of the optical fibre in which the pulse-broadening takes place. Consequently thorough...

  13. Development of SERS active fibre sensors

    CERN Document Server

    Polwart, E

    2002-01-01

    Surface-enhanced Raman scattering (SERS) is sensitive and selective and when coupled with fibre-optics could potentially produce an effective chemical sensing system. This thesis concerns the development of a single-fibre-based sensor, with an integral SERS-active substrate. A number of different methods for the manufacture of SERS-active surfaces on glass substrates were investigated and compared. The immobilisation of metal nanoparticles on glass functionalised with (3-aminopropyl)trimethoxysilane emerged as a suitable approach for the production of sensors. Substrates prepared by this approach were characterised using UV-visible spectroscopy, electron microscopy and Raman mapping. It was found that exposure of substrates to laser radiation led to a decrease in the signal recorded from adsorbed analytes. This speed of the decrease was shown to depend on the analyte, and the exciting wavelength and power. SERS-active fibre sensors were produced by immobilisation of silver nanoparticles at the distal end of a...

  14. Muscle fibre capillarization is a critical factor in muscle fibre hypertrophy during resistance exercise training in older men.

    Science.gov (United States)

    Snijders, Tim; Nederveen, Joshua P; Joanisse, Sophie; Leenders, Marika; Verdijk, Lex B; van Loon, Luc J C; Parise, Gianni

    2017-04-01

    Adequate muscle fibre perfusion is critical for the maintenance of muscle mass; it is essential in the rapid delivery of oxygen, nutrients and growth factors to the muscle, stimulating muscle fibre growth. Muscle fibre capillarization is known to decrease substantially with advancing age. However, whether (relative) low muscle fibre capillarization negatively impacts the muscle hypertrophic response following resistance exercise training in older adults is unknown. Twenty-two healthy older men (71 ± 1 years) performed 24 weeks of progressive resistance type exercise training. To assess the change in muscle fibre characteristics, percutaneous biopsies from the vastus lateralis muscle were taken before and following 12 and 24 weeks of the intervention programme. A comparison was made between participants who had a relatively low type II muscle fibre capillary-to-fibre perimeter exchange index (CFPE; LOW group) and high type II muscle fibre CFPE (HIGH group) at baseline. Type I and type II muscle fibre size, satellite cell, capillary content and distance between satellite cells to the nearest capillary were determined by immunohistochemistry. Overall, type II muscle fibre size (from 5150 ± 234 to 6719 ± 446 µm 2 , P muscle fibre, P muscle fibre capillarization, whereas muscle fibre size (from 5170 ± 390 to 7133 ± 314 µm 2 , P muscle fibre, P muscle fibre capillarization were observed in response to 12 and 24 weeks of resistance exercise training in both the LOW and HIGH group. Type II muscle fibre capillarization at baseline may be a critical factor for allowing muscle fibre hypertrophy to occur during prolonged resistance exercise training in older men. © 2016 The Authors. Journal of Cachexia, Sarcopenia and Muscle published by John Wiley & Sons Ltd on behalf of the Society on Sarcopenia, Cachexia and Wasting Disorders.

  15. Ca2+-activated force-generating properties of mammalian skeletal muscle fibres: histochemically identified single peeled rabbit fibres.

    Science.gov (United States)

    Donaldson, S K

    1984-12-01

    Single peeled (sarcolemma removed) rabbit skeletal muscle fibres, identified histochemically from their myofibrillar ATPase and oxidative staining patterns, were characterized according to their Ca2+-activated steady-state force-generating properties at normal intracellular pH (7.0) and under acidotic (pH 6.5) conditions. Maximum force-generating capacity of each fibre was assessed by measuring steady-state isometric force generation at saturating Ca2+ concentration at both pH values. The Ca2+ sensitivity of each fibre was ascertained by determining the percentage of maximum force generated at each of several subsaturating Ca2+ concentrations at both pH values. Fibres were selected from soleus, tibialis anterior and adductor magnus muscles. At subsaturating Ca2+ concentrations only two functional groups of fibres were distinguishable, corresponding to the histochemical classifications type I and type II. Type I fibres were more sensitive to Ca2+ and less depressed by acidosis than type II fibres in the subsaturating range of Ca2+ concentrations. At saturating Ca2+ concentrations, the acidotic depression of maximum force was significantly less for type I fibres than type II nonoxidative fibres regardless of their muscle of origin. Type II oxidative fibre maximum force properties depended upon the muscle of origin and demonstrated subgroups of these fibres that were different from type II nonoxidative fibres and similar to type I fibres.

  16. Study of injection moulded long glass fibre-reinforced polypropylene and the effect on the fibre length and orientation distribution

    Science.gov (United States)

    Parveeen, B.; Caton-Rose, P.; Costa, F.; Jin, X.; Hine, P.

    2014-05-01

    Long glass fibre (LGF) composites are extensively used in manufacturing to produce components with enhanced mechanical properties. Long fibres with length 12 to 25mm are added to a thermoplastic matrix. However severe fibre breakage can occur in the injection moulding process resulting in shorter fibre length distribution (FLD). The majority of this breakage occurs due to the melt experiencing extreme shear stress during the preparation and injection stage. Care should be taken to ensure that the longer fibres make it through the injection moulding process without their length being significantly degraded. This study is based on commercial 12 mm long glass-fibre reinforced polypropylene (PP) and short glass fibre Nylon. Due to the semi-flexiable behaviour of long glass fibres, the fibre orientation distribution (FOD) will differ from the orientation distribution of short glass fibre in an injection molded part. In order to investigate the effect the change in fibre length has on the fibre orientation distribution or vice versa, FOD data was measured using the 2D section image analyser. The overall purpose of the research is to show how the orientation distribution chnages in an injection moulded centre gated disc and end gated plaque geometry and to compare this data against fibre orientation predictions obtained from Autodesk Moldflow Simulation Insight.

  17. Investigation of digital light processing using fibre-reinforced polymers

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Nielsen, Jakob Skov

    2016-01-01

    -reinforced polymers in digital light processing (DLP) are limited. Fibre-reinforced polymer composites were manufactured into test objects using digital light processing. Short fibres were used in an unordered manner. An anisotropic property due to fibre orientation within the material was observed. The importance......Literature research shows multiple applications of fibre-reinforced polymers (FRP) respectively in fused deposition modelling and gypsum printing influencing the quality of the products in terms of stress and strain resistance as well as flexibility. So far, applications of fibre...... of fibre length and shape compared to layer thickness has been investigated including concepts to circumvent clustering of the fibres.This research contributes to the implementation of fibre-reinforced polymers in additive manufacturing technologies. Digital light processing allows generation...

  18. Ductile behavior of polyethylene fibre reinforced geopolymer composite

    Directory of Open Access Journals (Sweden)

    Ahmed Shaikh Faiz Uddin

    2017-01-01

    Full Text Available This paper presents the effects of various volume fractions of polyethylene (PE fibres of 0.5%, 1%, 1.5% and 2% on tensile, flexure and compressive behavior of PE fibres reinforced geopolymer composites (PE-FRGC. Results show that the 1% PE fibre by volume is the optimum fibre volume fraction for fly ash geopolymer composite, which exhibit superior strain and deflection hardening behavior in uni-axial tension and three-point bending, respectively. Results also show that the compressive strength of the composites decreases with increase in volume fractions of PE fibre. The fibre surface examination of PE fibre in the gopolymer matrix using scanning electron microscope (SEM and energy dispersive spectroscopy (EDS revealed no significant damage of PE fibre in the alkaline geopolymer matrix.

  19. Mechanical Properties of Man-Made Mineral glass fibres

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    ; man-made mineral glass fibres. The basaltic melt is prevented from crystallizing due to the high cooling rate, forming the mineral glass wool fibres. Basaltic mineral wool fibres are of high interest in industry due to their good chemical durability and excellent heat and sound insulation properties......In nature basaltic volcanic glass fibres are know from Hawaii as Pele's hair, formed by droplets of lava thrown into the air during volcanic eruption. The concept of glass fibre formation by an air stream dragging fibres from drops of melt is copied in industry to form basaltic glass wool fibres...... of the information gained from the mechanical tests, fracture characteristics of individual glass fibres are imaged by scanning electron microscopy. The fracture surfaces showed to fall in three groups; 1) surfaces including fracture mirror, mist and hackle, 2) bend fracture surfaces and 3) surfaces including pores...

  20. Extraction of nanocellulose fibrils from lignocellulosic fibres: a novel approach

    CSIR Research Space (South Africa)

    Abraham, E

    2011-06-01

    Full Text Available The objective of this work was to develop a simple process to obtain an aqueous stable colloid suspension of cellulose nano fibrils from various lignocellulosic fibres. For the preliminary analysis we have studied three different fibres: banana...

  1. Fractographic observations of the microstructural characteristics of flax fibre composites

    DEFF Research Database (Denmark)

    Madsen, Bo; Asian, Mustafa; Lilholt, Hans

    2016-01-01

    Natural fibre composites possess a number of special microstructural characteristics, which need to be documented to aid in the further development of these materials. Using field emission scanning electron microscopy, fractographic observations of the microstructural characteristics of aligned f...... novel observations, measurements and interpretations to be used in the further analysis and understanding of the properties of natural fibre composites. (C) 2015 Elsevier Ltd. All rights reserved.......Natural fibre composites possess a number of special microstructural characteristics, which need to be documented to aid in the further development of these materials. Using field emission scanning electron microscopy, fractographic observations of the microstructural characteristics of aligned...... flax fibre/thermoplastic composites are presented. The findings are presented in relation to the three operational parts in composites: fibres, matrix and fibre/matrix interface. For the flax fibres, the striated structure on the fibre surface is shown to consist of cellulose macrofibrils oriented...

  2. Geometrical Characterisation of Individual Fibres From X-Ray Tomograms

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Dahl, Vedrana Andersen; Mikkelsen, Lars Pilgaard

    2017-01-01

    We have developed an image analysis pipeline1 that can extract individual fibre tracksfrom low contrast X-ray tomograms of unidirectional composites with high fibre volumefraction. Measuring individual fibre tracks opens up the possibility of modelling thisempirical data in a statistical manner....... Thus, allowing to analyse the spatial distributionsof the parameters characterising the orientation and curvature of these individual fibres,which can also provide insights on the interactions amongst the individual fibres.Finite element models (FEMs) can be built from the extracted geometry...... to simulatethe performance of the scanned fibre structure under realistic conditions. Moreover, as-pects of the fibre architecture that inuence the macroscopic behaviour of the compositecan be quantified. Examples are 2D FEMs to predict the transverse stifiness or the quantification of fibre orientations...

  3. Association mapping and favourable QTL alleles for fibre quality ...

    Indian Academy of Sciences (India)

    To investigate the genetic mechanisms of fibre quality, a diverse panel of 403 Upland cotton accessions was grown, and the fibre quality traits were measured in six different environments. Genotyping was performed with genomewide simple ...

  4. Development of hemp fibre reinforced polypropylene composite - Journal Article

    CSIR Research Space (South Africa)

    Hargitai, H

    2005-06-01

    Full Text Available Nonwoven mats from hemp and polypropylene fibres in various proportions were produced and hot pressed to make composite material. The effect of fibre content and the anisotropy in nonwoven mat resulting from the carding technology were examined...

  5. FOAM CONCRETE REINFORCEMENT BY BASALT FIBRES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-10-01

    Full Text Available The authors demonstrate that the foam concrete performance can be improved by dispersed reinforcement, including methods that involve basalt fibres. They address the results of the foam concrete modeling technology and assess the importance of technology-related parameters. Reinforcement efficiency criteria are also provided in the article. Dispersed reinforcement improves the plasticity of the concrete mix and reduces the settlement crack formation rate. Conventional reinforcement that involves metal laths and rods demonstrates its limited application in the production of concrete used for thermal insulation and structural purposes. Dispersed reinforcement is preferable. This technology contemplates the infusion of fibres into porous mixes. Metal, polymeric, basalt and glass fibres are used as reinforcing components. It has been identified that products reinforced by polypropylene fibres demonstrate substantial abradability and deformability rates even under the influence of minor tensile stresses due to the low adhesion strength of polypropylene in the cement matrix. The objective of the research was to develop the type of polypropylene of D500 grade that would demonstrate the operating properties similar to those of Hebel and Ytong polypropylenes. Dispersed reinforcement was performed by the basalt fibre. This project contemplates an autoclave-free technology to optimize the consumption of electricity. Dispersed reinforcement is aimed at the reduction of the block settlement in the course of hardening at early stages of their operation, the improvement of their strength and other operating properties. Reduction in the humidity rate of the mix is based on the plasticizing properties of fibres, as well as the application of the dry mineralization method. Selection of optimal parameters of the process-related technology was performed with the help of G-BAT-2011 Software, developed at Moscow State University of Civil Engineering. The authors also

  6. Effects of hybrid composition of LCP and glass fibres on abrasive ...

    Indian Academy of Sciences (India)

    The effect of replacing glass fibre with LCP fibre on wear is reported. Wear loss increased with the applied loads and glass fibre contents in LLDPE. The replacements of glass fibres with LCP fibres improved abrasive wear resistance of composite. The composite containing 20 vol% of glass fibres in LLDPE showed the ...

  7. The synthesis and characterization of Mg-Zn-Ca alloy by powder metallurgy process

    Energy Technology Data Exchange (ETDEWEB)

    Annur, Dhyah; Franciska, P.L.; Erryani, Aprilia; Amal, M. Ikhlasul; Kartika, Ika, E-mail: pepeng2000@yahoo.com [Research center for Metallurgy and Material, Indonesian Institute of Science (Indonesia); Sitorus, Lyandra S. [Sultan Ageng Tirtayasa University (Indonesia)

    2016-04-19

    Known for its biodegradation and biocompatible properties, magnesium alloys have gained many interests to be researched as implant material. In this study, Mg-3Zn-1Ca, Mg-29Zn-1Ca, and Mg-53Zn-4.3Ca (in wt%) were synthesized by means of powder metallurgy method. The compression strength and corrosion resistance of magnesium alloy were thoroughly examined. The microstructures of the alloy were characterized using optical microscopy, Scanning Electron Microscope, and also X-ray diffraction analysis. The corrosion resistance were evaluated using electrochemical analysis. The result indicated that Mg- Zn- Ca alloy could be synthesized using powder metallurgy method. This study showed that Mg-29Zn-1Ca would make the highest mechanical strength up to 159.81 MPa. Strengthening mechanism can be explained by precipitation hardening and grain refinement mechanism. Phase analysis had shown the formation of α Mg, MgO, and intermetallic phases: Mg2Zn11 and also Ca2Mg6Zn3. However, when the composition of Zn reach 53% weight, the mechanical strength will be decreasing. In addition, all of Mg-Zn-Ca alloy studied here had better corrosion resistance (Ecorr around -1.4 VSCE) than previous study of Mg. This study indicated that Mg- 29Zn- 1Ca alloy can be further analyzed to be a biodegradable implant material.

  8. Development of processes for zircaloy chips recycling by electric arc furnace remelting and powder metallurgy

    International Nuclear Information System (INIS)

    Pereira, Luiz Alberto Tavares

    2014-01-01

    PWR reactors employ, as nuclear fuel, UO 2 pellets with Zircaloy clad. In the fabrication of fuel element parts, machining chips from the alloys are generated. As the Zircaloy chips cannot be discarded as ordinary metallic waste, the recycling of this material is important for the Brazilian Nuclear Policy, which targets the reprocess of Zircaloy residues for economic and environmental aspects. This work presents two methods developed in order to recycle Zircaloy chips. In one of the methods, Zircaloy machining chips were refused using an electric-arc furnace to obtain small laboratory ingots. The second one uses powder metallurgy techniques, where the chips were submitted to hydriding process and the resulting material was milled, isostatically pressed and vacuum sintered. The ingots were heat-treated by vacuum annealing. The microstructures resulting from both processing methods were characterized using optical and scanning electron microscopy. Chemical composition, crystal phases and hardness were also determined. The results showed that the composition of recycled Zircaloy comply with the chemical specifications and presented adequate microstructure for nuclear use. The good results of the powder metallurgy method suggest the possibility of producing small parts, like cladding end-caps, using near net shape sintering. (author)

  9. Microstructural and electrical investigation of Cu-Ni-Cr alloys obtained by powder metallurgy method

    Energy Technology Data Exchange (ETDEWEB)

    Carrio, Juan A.G.; Carvalhal, M.A.; Ayabe, L.M.; Monteiro, W.A., E-mail: jgcarrio@mackenzie.br [Universidade Presbiteriana Mackenzie (UPM/CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades. Dept. de Fisica; Silva, L.C.E. da; Silva Junior, R.V., E-mail: fisica.cch@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    The aim of this work, using the powder metallurgy process, is to synthesize metallic alloys with high mechanical strength and high electric conductivity, after melting optimizing and thermal treatments. The Cu-Ni-Cr (wt%) alloys are characterized in their mechanical and electrical properties as well as the obtained microstructure. Through the process of powder metallurgy, contacts and structural parts can be obtained. The alloys elements are added to copper with the intention to improve their strength, ductility and thermal stability, without causing considerable damages in their form, electrical and thermal conductivity, and corrosion resistance. The metallic powders were mixed for a suitable time and then they were pressed in a cold uniaxial pressing (1000 kPa). Afterwards, the specimens were sintered in temperatures varying from 700 up to 800 deg C under vacuum. At last, the samples were homogenized at 550 deg C under vacuum, for special times. The comparative analysis is based on the sintered density, densification parameter, hardness, macrostructures and microstructures of the samples. The alloys were characterized by optical microscopy, X-rays powder diffraction, electrical conductivity and Vickers hardness. (author)

  10. Summary of NRC LWR safety research programs on fuel behavior, metallurgy/materials and operational safety

    International Nuclear Information System (INIS)

    Bennett, G.L.

    1979-09-01

    The NRC light-water reactor safety-research program is part of the NRC regulatory program for ensuring the safety of nuclear power plants. This paper summarizes the results of NRC-sponsored research into fuel behavior, metallurgy and materials, and operational safety. The fuel behavior research program provides a detailed understanding of the response of nuclear fuel assemblies to postulated off-normal or accident conditions. Fuel behavior research includes studies of basic fuel rod properties, in-reactor tests, computer code development, fission product release and fuel meltdown. The metallurgy and materials research program provides independent confirmation of the safe design of reactor vessels and piping. This program includes studies on fracture mechanics, irradiation embrittlement, stress corrosion, crack growth, and nondestructive examination. The operational safety research provides direct assistance to NRC officials concerned with the operational and operational-safety aspects of nuclear power plants. The topics currently being addressed include qualification testing evaluation, fire protection, human factors, and noise diagnostics

  11. Acoustic harmonic generation measurement applications: Detection of tight cracks in powder metallurgy compacts

    International Nuclear Information System (INIS)

    Barnard, D.J.; Foley, J.C.

    2000-01-01

    Standard linear ultrasonic testing techniques have long been employed for locating and characterizing relatively open cracks in a wide variety of materials, from metallic alloys and ceramics to composites. In all these materials, the detection of open cracks easily accomplished because the void between the two crack surfaces provides sufficient acoustic impedance mismatch to reflect the incident energy. Closed or partially closed cracks, however, may often go undetected because contacting interfaces allow transmission of ultrasound. In the green (unsintered) state, powder metallurgy compacts typically contain high residual stresses that have the ability to close cracks formed during the compaction process, a result of oxide films, improper powder lubricant, mold design, etc. After sintering, the reduction of residual stresses may no longer be sufficient to close the crack. Although the crack may be more easily detected, it is obvious most desirable to discover defects prior to sintering. It has been shown that the displacements of an interface may be highly nonlinear if a stress wave of sufficient intensity propagates across it, a result of the stress wave either opening or closing the interface. Current efforts involve the application of nonlinear acoustic techniques, in particular acoustic harmonic generation measurements, for the detection and characterization of tightly closed cracks in powder metallurgy parts. A description of the equipment and the measurement technique will be discussed and initial experimental results on sintered and green compacts will be presented. - This work was performed at the Ames Laboratory, Iowa State University under USDOE Contract No. W-7405-ENG-82

  12. Characterization of aluminum/steel components from recycled swarf using the powder metallurgy as technique

    International Nuclear Information System (INIS)

    Souza, V.E.S.; Masieiro, F.R.S.; Lourenco, J.M.; Felipe, R.C.T.S.

    2009-01-01

    Full text: The powder metallurgy process consists to produce metallic or ceramic components through pressure in a powder mass. These components will be submitted to a sintering temperature in order to consolidate them and then improve their mechanical proprieties. The industry is responsible for the swarf generation from different manufacture process. This paper has main goal the reutilization of aluminum and steel swarf using the powder metallurgy as technique. The methodology used in this work consists to compact Al 6060 plus steel SAE 1045 as reinforce material at 250MPa, 400MPa and 600MPa. The composition about these compacted will be 30%, 40%, 50% of steel into aluminum matrix. In this way will be analyze the hardness as function of the compressibility and quantity of steel. The samples will be processed at 500°C during 45 minutes using a resistive furnace in a hydrogen atmosphere. Micrographs of the sintered samples will be obtained by using a Scanning Electron Microscope and Optic Microscope. X-rays diffraction will be also used to characterize the phases found to due diffusivity between the steel and aluminum. (author)

  13. Development of an extra-high strength powder metallurgy nickel-base superalloy

    Science.gov (United States)

    Kent, W. B.

    1977-01-01

    A program was conducted to optimize the composition of NASA IIb-11, an alloy originally developed as a wrought material, for thermal stability and to determine the feasibility for producing the alloy using powder metallurgy techniques. Seven compositions were melted and atomized, hot isostatically pressed, cross rolled to disks and heat treated. Tensile and stress rupture properties from room temperature to 870 C (1600 F) were determined in addition to thermal stability characteristics. Processing variables included hot isostatic pressing parameters and handling, cross rolling procedures and heat treatment cycles. NASA IIb-11E displayed the best combination of overall properties for service as a 760 C (1400 F) disk material. Its composition is 0.06 C, 8.5 Cr, 9.0 Co, 2.0 Mo, 7.1 W, 6.6 Ta, 4.5 Al, 0.75 Ti, 0.5 V, 0.7 Hf, 0.01 B, 0.05 Zr and balance Ni. While the alloy exhibits the highest 760 C (1400 F) rupture strength reported for any powder metallurgy disk alloy to date, additional studies to further evaluate the effects of heat treatment may be required. The alloy is not susceptible to topologically close-packed phase formation during thermal exposure at 870 C (1600 F) for 1,500 hours, but its mechanical property levels are lowered due to grain boundary carbide formation.

  14. Analysis of cancer mortality risk among workers of a research uranium metallurgy division in France

    International Nuclear Information System (INIS)

    Jejati, H.; Laurier, D.; Tirmarche, M.; Giraud, J.M.

    1997-01-01

    This cohort study has been undertaken in response to a suspected cluster of cancers mentioned by workers involved in research activities concerning the metallurgy of uranium. The studied population included all persons having worked between 1950 and 1968 at the Metallurgy Division of the French Atomic Energy Commission (CEA). Exposures were registered on an individual annual basis. For analysis, they were grouped in three categories: use of chemicals agents (Benzene, beryllium, alcohols, solvents ...), manipulation of radioactive materials (uranium, thorium, fission decay products), and exposure to external radiation. This relatively small cohort included 356 workers followed up to December 1990. Out of observed deaths, 21 were from cancer. Total mortality from cancer was less than expected from national rates (Standardised Mortality Ratio = 0.73). Cancer mortality did not increase with duration of exposure to external radiation or with duration of manipulation of radioactive materials. Risk of cancer was increasing with the number of years of exposure to chemicals. The small size of this cohort limits the conclusion of the observed results. The purpose, despite this lack of power, was to answer a worry of the workers, more than to estimate a clear dose-response relationship linked to a specific cancer site. The effect studied here is ''all cancers'', a distinction of the different sites being uninformative because of the very small number of cases observed. Nevertheless, this study suggests some routes for further research: it highlights the importance of considering concomitant exposures like chemical ones in studies of nuclear workers. (author)

  15. Porous titanium scaffolds fabricated using a rapid prototyping and powder metallurgy technique.

    Science.gov (United States)

    Ryan, Garrett E; Pandit, Abhay S; Apatsidis, Dimitrios P

    2008-09-01

    One of the main issues in orthopaedic implant design is the fabrication of scaffolds that closely mimic the biomechanical properties of the surrounding bone. This research reports on a multi-stage rapid prototyping technique that was successfully developed to produce porous titanium scaffolds with fully interconnected pore networks and reproducible porosity and pore size. The scaffolds' porous characteristics were governed by a sacrificial wax template, fabricated using a commercial 3D-printer. Powder metallurgy processes were employed to generate the titanium scaffolds by filling around the wax template with titanium slurry. In the attempt to optimise the powder metallurgy technique, variations in slurry concentration, compaction pressure and sintering temperature were investigated. By altering the wax design template, pore sizes ranging from 200 to 400 microm were achieved. Scaffolds with porosities of 66.8 +/- 3.6% revealed compression strengths of 104.4+/-22.5 MPa in the axial direction and 23.5 +/- 9.6 MPa in the transverse direction demonstrating their anisotropic nature. Scaffold topography was characterised using scanning electron microscopy and microcomputed tomography. Three-dimensional reconstruction enabled the main architectural parameters such as pore size, interconnecting porosity, level of anisotropy and level of structural disorder to be determined. The titanium scaffolds were compared to their intended designs, as governed by their sacrificial wax templates. Although discrepancies in architectural parameters existed between the intended and the actual scaffolds, overall the results indicate that the porous titanium scaffolds have the properties to be potentially employed in orthopaedic applications.

  16. Environmental legacy of copper metallurgy and Mongol silver smelting recorded in Yunnan Lake sediments.

    Science.gov (United States)

    Hillman, Aubrey L; Abbott, Mark B; Yu, JunQing; Bain, Daniel J; Chiou-Peng, TzeHuey

    2015-03-17

    Geochemical measurements on well-dated sediment cores from Lake Er (Erhai) are used to determine the timing of changes in metal concentrations over 4500 years in Yunnan, a borderland region in southwestern China noted for rich mineral deposits but with inadequately documented metallurgical history. Our findings add new insight into the impacts and environmental legacy of human exploitation of metal resources in Yunnan history. We observe an increase in copper at 1500 BC resulting from atmospheric emissions associated with metallurgy. These data clarify the chronological issues related to links between the onset of Yunnan metallurgy and the advent of bronze technology in adjacent Southeast Asia, subjects that have been debated for nearly half a century. We also observe an increase from 1100 to 1300 AD in a number of heavy metals including lead, silver, zinc, and cadmium from atmospheric emissions associated with silver smelting. Culminating during the rule of the Mongols, known as the Yuan Dynasty (1271-1368 AD), these metal concentrations approach levels three to four times higher than those from industrialized mining activity occurring within the catchment today. Notably, the concentrations of lead approach levels at which harmful effects may be observed in aquatic organisms. The persistence of this lead pollution over time created an environmental legacy that likely contributes to known issues in modern day sediment quality. We demonstrate that historic metallurgical production in Yunnan can cause substantial impacts on the sediment quality of lake systems, similar to other paleolimnological findings around the globe.

  17. Microstructural and mechanical characteristics of porous iron prepared by powder metallurgy.

    Science.gov (United States)

    Capek, Jaroslav; Vojtěch, Dalibor

    2014-10-01

    The demand for porous biodegradable load-bearing implants has been increasing recently. Based on investigations of biodegradable stents, porous iron may be a suitable material for such applications. In this study, we prepared porous iron samples with porosities of 34-51 vol.% by powder metallurgy using ammonium bicarbonate as a space-holder material. We studied sample microstructure (SEM-EDX and XRD), flexural and compressive behaviors (universal loading machine) and hardness HV5 (hardness tester) of the prepared samples. Sample porosity increased with the amount of spacer in the initial mixtures. Only the pore surfaces had insignificant oxidation and no other contamination was observed. Increasing porosity decreased the mechanical properties of the samples; although, the properties were still comparable with human bone and higher than those of porous non-metallic biomaterials and porous magnesium prepared in a similar way. Based on these results, powder metallurgy appears to be a suitable method for the preparation of porous iron for orthopedic applications. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Fractionation study in bioleached metallurgy wastes using six-step sequential extraction.

    Science.gov (United States)

    Krasnodebska-Ostrega, Beata; Pałdyna, Joanna; Kowalska, Joanna; Jedynak, Łukasz; Golimowski, Jerzy

    2009-08-15

    The stored metallurgy wastes contain residues from ore processing operations that are characterized by relatively high concentrations of heavy metals. The bioleaching process makes use of bacteria to recover elements from industrial wastes and to decrease potential risk of environmental contamination. Wastes were treated by solutions containing bacteria. In this work, the optimized six-stage sequential extraction procedure was applied for the fractionation of Ni, Cr, Fe, Mn, Cu and Zn in iron-nickel metallurgy wastes deposited in Southern Poland (Szklary). Fractionation and total concentrations of elements in wastes before and after various bioleaching treatments were studied. Analyses of the extracts were performed by ICP-MS and FAAS. To achieve the most effective bioleaching of Zn, Cr, Ni, Cu, Mn, Fe the usage of both autotrophic and heterotrophic bacteria in sequence, combined with flushing of the residue after bioleaching is required. 80-100% of total metal concentrations were mobilized after the proposed treatment. Wastes treated according to this procedure could be deposited without any risk of environmental contamination and additionally the metals could be recovered for industrial purposes.

  19. Fibre Bragg Grating and Long Period Grating Sensors in Polymer Optical Fibres

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar

    in ΔΛfast. It would have the highest sensing range around 3%. In the last part of the FBG section, a simple fibre FBG microphone is investigated, and the influence of a membrane amplifier on sound detection is also investigated. In the last part of the thesis the LPG inscription system is shown...... which translates the outside pressure into strain on the fibre. The transducer consisted of a 3Dprinted skeleton through which the fibre is pulled. A latex material is then wrapped around it and all the holes were sealed in order to prevent the air from leaking out. The pod transducer was tested...

  20. A Fibre Bragg Grating Interrogation Technique Based on High Birefringence Fibre Loop Mirror and WDM

    Directory of Open Access Journals (Sweden)

    Zhang Xun

    2016-01-01

    Full Text Available In this paper, a fibre Bragg grating (FBG interrogation technique based on high Birefringence fibre loop mirror (Hi-Bi FLM and wavelength division multiplexer (WDM is proposed and demonstrated. The approximate linear edge of the transmittance of the Hi-Bi FLM, which is a sinusoidal function of wavelength, is used to interrogate the sensing FBGs and WDMs is used to realize wavelength discrimination .Suitable for both static and dynamic sensing, this interrogation method has the advantages of all fibre design and high stability.

  1. Fibre Optical Parametric Amplification in Defect Bragg Fibres with Zero Dispersion Slow Light Effect

    International Nuclear Information System (INIS)

    Li, Xiao; Wei, Zhang; Yi-Dong, Huang; Jiang-De, Peng; Hong, Zhao; Ke-Wu, Yang

    2008-01-01

    Nonlinearity enhancement by slow light effect and strong light confinement in defect Bragg fibres is demonstrated and analysed in applications of fibre optical parametric amplifiers. Broadband low group velocity and zero dispersion as well as the strong light confinement by band gap enhances the nonlinear coefficient up to more than one order than the conventional high nonlinear fibres. Moreover, the zero dispersion wavelength of coupled core mode can be designed arbitrarily, under which the phase-matching bandwidth of the nonlinear process can be extended. (fundamental areas of phenomenology (including applications))

  2. CAPSULES AS A PREVENTION OF FIBRE CLUSTERS IN CONCRETE

    OpenAIRE

    JOSEF STRYK; KAREL POSPíšIL; RADEK MATULA

    2012-01-01

    Homogenous concrete mixture without aggregate pockets and fibre clusters is a presumption for appropriate properties of concrete element or structure. There are technological measures how to achieve homogenously looking mixture from aggregate point of view, but fibres are still predisposed for clusters forming. The paper evaluates originally designed and protected within European patent treatment of fibre, based on capsules containing individual rolled fibre which can be admixed into a concre...

  3. Steel fibre corrosion in cracks:durability of sprayed concrete

    OpenAIRE

    Nordström, Erik

    2000-01-01

    Steel fibre reinforced sprayed concrete is common practice for permanent linings in underground construction. Today there is a demand on "expected technical service life" of 120 years. Thin steel fibres could be expected to discontinue carrying load fast with a decrease of fibre diameter caused by corrosion, especially in cracks. The thesis contains results from inspections on existing sprayed concrete structures and a literature review on corrosion of steel fibres in cracked concrete. To stu...

  4. Zeonex Microstructured Polymer Optical Fibre Bragg Grating Sensor

    DEFF Research Database (Denmark)

    Woyessa, Getinet; Fasano, Andrea; Markos, Christos

    2016-01-01

    We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time.......We fabricated an endlessly single mode and humidity insensitive Zeonex microstructured polymer optical fibre (mPOF) for fibre Bragg grating (FBG) temperature and strain sensors. We inscribed and characterise FBGs in Zeonex mPOF for the first time....

  5. Spider silk: a novel optical fibre for biochemical sensing

    OpenAIRE

    Hey Tow, Kenny; Chow, Desmond; Vollrath, Fritz; Dicaire, Isabelle; Gheysens, Tom; Thévenaz, Luc

    2015-01-01

    Whilst being thoroughly used in the textile industry and biomedical sector, silk has not yet been exploited for fibre optics-based sensing although silk fibres directly obtained from spiders can guide light and have shown early promises to being sensitive to some solvents. In this communication, a pioneering optical fibre sensor based on spider silk is reported, demonstrating for the first time the use of spider silk as an optical fibre sensor to detect polar solvents such as water, ammonia a...

  6. Orientation of fibres in suspensions flowing over a solid surface

    OpenAIRE

    Carlsson, Allan

    2007-01-01

    The orientation of fibres suspended in a viscous fluid, flowing over a solid surface, has been studied experimentally. A shear layer was generated, by letting the suspension flow down an inclined plate. Far upstream from the measuring section the suspension was accelerated to obtain an initial orientation of the fibres aligned with the flow direction. A CCD-camera was used to visualise the fibres. The velocity profile of the fibres coincided with the theoretical expression for fully developed...

  7. Solution electrospinning of particle-composite fibres

    DEFF Research Database (Denmark)

    Christiansen, Lasse; Fojan, Peter

    2016-01-01

    Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio.......Electrospinning is a simple and fast way to produce nano- and microfibers. By applying high voltage to a droplet of solution or polymer melt, fibre mats can be produced. These mats are porous in the micrometre domain, and have a high surface area to volume ratio....

  8. Durability of cracked fibre reinforced concrete structures

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan De Place; Nielsen, Laila

    1997-01-01

    (capillary water uptake) is used, involving an in-situ method and a laboratory method. Three different concrete qualities as well as steel fibres (ZP) and polypropylene fibres (PP) are used. Results of the durability tests on cracked FRC-beams are compared to results for uncracked FRC-beams and beams without......Durability studies are carried out by subjecting FRC-beams to combined mechanical and environmental load. Mechanical load is obtained by exposing beams to il-point bending until a predefined crack width is reached, using a newly developed test setup. As environmental load, exposure to water...

  9. Fibre-based imaging: new challenges

    Science.gov (United States)

    Plöschner, Martin; Straka, Branislav; Dholakia, Kishan; Čižmár, TomáÅ.¡

    2015-03-01

    A novel minimally invasive micro-endoscopes utilizing disordered light within a standard multimode optical fibre have been introduced recently. The two most important limitations of this exciting technology are (i) the lack of bending flexibility (transformation matrix is only valid as long as the fibre remains stationary) and (ii) high demands on computational power, making the performance of such systems slow. Here we discuss possible routes to address the later one: We introduce a GPU toolbox to make this powerful technique faster and more accessible to bio-medical researchers.

  10. Benign Fibröz Histiositoma

    OpenAIRE

    ÖĞÜTCEN TOLLER, Melahat; ÖZKAN, Nilüfer; YILDIZ, Levent

    2015-01-01

    Benign fibröz histiositoma (BFH), ağız kavitesinde nadir görülen, klinik ve histopatolojik olarak teşhiste karışıklığa yol açan bir tümördür. Bu makalede, sağ mandibular bukkal bölgede görülen bir benign fibröz histiositoma vakası sunularak, klinik ve histopatolojik özellikleri tartışıldı.

  11. A statistical analysis of fibre size and shape distribution after compounding in composites reinforced by natural fibres

    NARCIS (Netherlands)

    Moigne, Le N.; Oever, van den M.J.A.; Budtova, T.

    2011-01-01

    Using high resolution optical microscopy coupled with image analysis software and statistical methods, fibre length and aspect ratio distributions in polypropylene composites were characterized. Three types of fibres, flax, sisal and wheat straw, were studied. Number and surface weighted

  12. Dietary fibres in the regulation of appetite and food intake

    DEFF Research Database (Denmark)

    Kristensen, Mette; Jensen, Morten Møller Georg

    2011-01-01

    it is essential to have an understanding of individual dietary fibre viscosity characteristics. The goal of this paper is to provide a brief overview on the role of dietary fibres in appetite regulation highlighting the importance of viscosity and also include new findings on the role of linseed dietary fibre...

  13. Effects of dietary fibre on behaviour and satiety in pigs

    NARCIS (Netherlands)

    Leeuw, de J.A.; Bolhuis, J.E.; Bosch, G.; Gerrits, W.J.J.

    2008-01-01

    During the past decades there has been considerable interest in the use of dietary fibre in both animal and human nutrition. In human subjects dietary fibre has been studied intensively for possible effects on body-weight management and health. In animal nutrition the interest in dietary fibre has

  14. Distribution of Elastic Fibres in the Human Abdominal Linea Alba ...

    African Journals Online (AJOL)

    The linea alba (LA) supports biomechanical stress generated by intra-abdominal pressure. It is believed to contain connective tissue fibres, which provide tensile strength and pliancy. Previous studies have dwelt on collagen fibres with scarce reports on elastic fibres. Biomechanical studies have shown that the LA has ...

  15. Association mapping and favourable QTL alleles for fibre quality ...

    Indian Academy of Sciences (India)

    Cheng-Guang Dong

    Abstract. Improving cotton fibre quality is a major breeding goal for Upland cotton in China. To investigate the genetic mechanisms of fibre quality, a diverse panel of 403 Upland cotton accessions was grown, and the fibre quality traits were measured in six different environments. Genotyping was performed with ...

  16. Tensile behaviour of polyethylene and poly(p-xylylene) fibres

    NARCIS (Netherlands)

    van der Werff, Harm

    1991-01-01

    This thesis deals with the tensile behaviour of fibres prepared from high molecular weight polymers.The tensile strength of a polymeric fibre is in general much lower than the corresponding theoretical value. In case of ultra-high molecular weight polyethylene (UHMWPE), fibres can be prepared by

  17. Modelling fibre laydown and web uniformity in nonwoven fabric

    Science.gov (United States)

    Battocchio, F.; Sutcliffe, M. P. F.

    2017-04-01

    The mechanical and functional performance of nonwoven fabric critically depends on the fibre architecture. The fibre laydown process plays a key role in controlling this architecture. The fibre dynamic behaviour during laydown is studied through a finite element model which describes the role of the parameters in defining the area covered by a single fibre when deposited on the conveyor belt. The path taken by a fibre is described in terms of the radius of gyration, which characterises the area covered by the fibre in the textile, and the spectrum of curvature, which describes the degree of fibre looping as a function of the arc length. Starting from deterministic and idealised fibre curvature spectra, stochastic Monte Carlo simulations are undertaken to generate full nonwoven web samples and reproduce the uniformity of fibre density. A novel image analysis technique that allows measurement of the uniformity of real spunbonded nonwoven samples from images of textiles is used to confirm the validity of the model. It is shown that the main parameter that governs the fibre density uniformity is the ratio of the fibre spinning velocity to the velocity of conveyor belt, while fibre oscillations prior to deposition play a secondary role.

  18. Optical fibre probes in the measurement of scattered light

    Indian Academy of Sciences (India)

    2014-01-08

    Jan 8, 2014 ... An optrode usually comprises a bundle of multimode fibres, out of which one or more fibres are used for irradiating the sample, and the remaining fibres are used to collect the light reflected/scattered/fluoresced from the sample containing the measurand(s). The so-collected light carries the characteristic ...

  19. Design of fibre reinforced PV concepts for building integrated applications

    NARCIS (Netherlands)

    Reinders, Angelina H.M.E.; de Wit, H.; de Boer, Andries; Ossenbrink Sinke, W.; Helm, P.

    2009-01-01

    Fibre reinforced polymers present an interesting encapsulation medium for PV-modules. Glass fibres can provide increased strength and stiffness to thin polymer layers overcoming the brittleness and limited deformability of glass-panes. Glass fibre reinforced polymers allows for transparency over a

  20. Continuous jute fibre reinforced laminated paper composite and ...

    Indian Academy of Sciences (India)

    Plastic bags create a serious environmental problem. The proposed jute fibre reinforced laminated paper composite and reinforcement-fibre free paper laminate may help to combat the war against this pollutant to certain extent. The paper laminate, without reinforcement fibre, exhibited a few fold superiority in tensile ...

  1. Mechanical property analysis of kenaf–glass fibre reinforced ...

    Indian Academy of Sciences (India)

    mechanical properties and are used as reinforcing materials in polymer composites [3–5]. However, the products made from natural fibre composite are still limited to the structural applications, owing to their poor mechanical prop- erties [6]. To solve this issue, the natural fibres are hybridized with synthetic fibres to make the ...

  2. Compressive behaviour of unidirecterional flax fibre reinforced composites

    NARCIS (Netherlands)

    Bos, H.L.; Molenveld, K.; Teunissen, W.; Wingerde, van A.M.; Delft, van D.R.V.

    2004-01-01

    The compressive strength of unidirectional flax fibre epoxy composites was studied. The compressive strength is influenced negatively by the presence of kink bands in the flax fibres. Improvement of the adhesion between the fibres and the epoxy resin can be achieved easily by removing the thin wax

  3. Investigation on effect of fibre hybridization and orientation on ...

    Indian Academy of Sciences (India)

    This paper aimsto find the effect of fibre hybridization and orientation on mechanical behaviour of composite fabricated with neem, abacafibres and epoxy resin. Here, three varieties of composites are fabricated namely, composite 1 which consists of abaca fibreand glass fibre, composite 2, which consists of neem fibre and ...

  4. Effect of fibre content and alkali treatment on mechanical properties ...

    Indian Academy of Sciences (India)

    Roystonea regia fibre; epoxy resin; alkali treatment; mechanical properties. Abstract. The present paper investigates the effect of fibre content and alkali treatment on tensile, flexural and impact properties of unidirectional Roystonea regia natural-fibre-reinforced epoxy composites which are partially biodegradable.

  5. Mechanical properties of natural fibre reinforced polymer composites

    Indian Academy of Sciences (India)

    During the last few years, natural fibres have received much more attention than ever before from the research community all over the world. These natural fibres offer a number of advantages over traditional synthetic fibres. In the present communication, a study on the synthesis and mechanical properties of new series of ...

  6. Study on durability of natural fibre concrete composites using ...

    Indian Academy of Sciences (India)

    was done using glass and palm tree fibres on high strength concrete. Mechanical strength properties such as compres- ... are comparable with glass fibres. A finite element analysis was also done using ANSYS ... internal friction were determined for three different mix ratios and four different aspect ratios and fibre contents.

  7. Fabrication of silicon based glass fibres for optical communication

    Indian Academy of Sciences (India)

    Silicon based glass fibres are fabricated by conventional fibre drawing process. First, preform fabrication is carried out by means of conventional MCVD technique by using various dopants such as SiCl4, GeCl4, POCl3, and FeCl3. The chemicals are used in such a way that step index single mode fibre can be drawn.

  8. Microwave absorbing properties of activated carbon fibre polymer ...

    Indian Academy of Sciences (India)

    absorption characteristics of the ACF composite with one containing unactivated fibres, it is found that carbon fibre activation increases the absorption of the composite. Keywords. Activated carbon fibres; microwave absorbing properties; composite materials. 1. Introduction. The reduction of electromagnetic backscatter with ...

  9. Fabrication of silicon based glass fibres for optical communication

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Silicon based glass fibres are fabricated by conventional fibre drawing process. First, preform fabrication is carried out by means of conventional MCVD technique by using various dopants such as SiCl4,. GeCl4, POCl3, and FeCl3. The chemicals are used in such a way that step index single mode fibre can be.

  10. Effect of alkali treated jute fibres on composite properties

    Indian Academy of Sciences (India)

    Vinylester resin; jute fibre composite; alkali; mechanical properties; fracture; fibre pull out. ... For the 35% composites with 4 h treated fibres, the flexural strength improved from 199.1 MPa to 238.9 MPa by 20%, modulus improved from 11.89 GPa to 14.69 GPa by 23% and laminar shear strength increased from 0.238 MPa to ...

  11. Preparation of ultrafine poly(sodium 4-styrenesulfonate) fibres via ...

    Indian Academy of Sciences (India)

    The ultrafine poly (sodium 4-styrenesulfonate) (NaPSS) fibres have been prepared for the first time by electrospinning. The spinning solutions (NaPSS aqueous solutions) in varied concentrations were studied for electrospinning into ultrafine fibres. The results indicated that the smooth fibre could be formed when the ...

  12. Optical fibre probes in the measurement of scattered light ...

    Indian Academy of Sciences (India)

    2014-01-08

    Jan 8, 2014 ... absorption of light from the sample solution. Details of the experiments and results are presented here. Keywords. Fibre optic sensors; optical fibre probes; turbidity sensor; optical properties. PACS Nos 42.81.−I; 42.81.Pa; 78.15.+e. 1. Introduction. Apart from being the transmission medium in optical fibre ...

  13. Natural Pineapple Leaf Fibre Extraction On Josapine And Morris

    Directory of Open Access Journals (Sweden)

    Mazalan Muhammad Firdaus

    2017-01-01

    Full Text Available The pineapple’s leaf plant contains approximately 2.5% to 3.5% of strong white silky fibres. These fibres are useful and can be extracted from the leaves. There are a few ways to extract the fibre such as hand scrapping and by extraction machine. The objective of this research is to study the quality of fibre extraction by using different age of pineapple leaf. Next, the study aims to compare the quality of Josapine and Morris pineapple leaf with tensile test. Fibre yield percentage are calculated to determine which type of pineapple leaf produce high production of dry fibre. The mechanical properties of the fibres are analysed by Tensile Test under American Standard Testing Methods (ASTM C1577-03 and Scanning Electron Microscope (SEM. The result of the fibre yield percentage show the Josapine type on 12 month ages are the highest value fibre yield percentage which is 7.89%. Based on fibre yield percentages, it showed the Josapine type produce better dry fibre production compare to Morris type. Based on mechanical test, it showed Josapine type on 12 months ages are the strongest fibre compare to Morris type since it can withstand on 67.6 N of load.

  14. Dietary Fibre in Health and Disease | Kolawole | Nigerian Endocrine ...

    African Journals Online (AJOL)

    The mechanism by which dietary fibre exerts its various effects have been the subject several studies. Its ability to slow food digestion and nutrient absorption is well known. This review summarises the broader literature on what constitutes dietary fibre, mechanisms of action of dietary fibre, and its impact on some disease ...

  15. Mechanical properties of short-flax-fibre reinforced compounds

    NARCIS (Netherlands)

    Bos, H.L.; Müssig, J.; Oever, van den M.J.A.

    2006-01-01

    The mechanical properties of flax/polypropylene compounds, manufactured both with a batch kneading and an extrusion process were determined and compared with the properties of Natural fibre Mat Thermoplastic (NMT) composites. The fibre length and width distributions of the fibres from the compounds

  16. Microbending in photonic crystal fibres - an ultimate loss limit?

    DEFF Research Database (Denmark)

    Bjarklev, Anders Overgaard; Hansen, Theis Peter; Hougaard, Kristian G.

    2001-01-01

    Microbending losses are for the first time estimated in index-guiding photonic crystal fibres, and comparisons with standard step-index fibres are made. The results indicate that typical photonic crystal fibres are significantly less sensitive (one order of magnitude smaller loss) towards...

  17. Optical fibre Bragg grating recorded in TOPAS cyclic olefin copolymer

    DEFF Research Database (Denmark)

    Johnson, I.P.; Yuan, Scott Wu; Stefani, Alessio

    2011-01-01

    A report is presented on the inscription of a fibre Bragg grating into a microstructured polymer optical fibre fabricated from TOPAS cyclic olefin copolymer. This material offers two important advantages over poly (methyl methacrylate), which up to now has formed the basis for polymer fibre Bragg...

  18. Effects of moisture on the mechanical properties of glass fibre ...

    Indian Academy of Sciences (India)

    Similarly, 27.48 wt% nascent fibre reinforced composites and those composites with boiling water treatment showed the estimation of defect concentrations of 39.94% and 50.55% respectively. SEM study of the fractured surfaces showed heavy fibre pull-out in the tensile zone whilst shear fracture of the fibre bundles was ...

  19. Multicore fibre photonic lanterns for precision radial velocity Science

    Science.gov (United States)

    Gris-Sánchez, Itandehui; Haynes, Dionne M.; Ehrlich, Katjana; Haynes, Roger; Birks, Tim A.

    2018-04-01

    Incomplete fibre scrambling and fibre modal noise can degrade high-precision spectroscopic applications (typically high spectral resolution and high signal to noise). For example, it can be the dominating error source for exoplanet finding spectrographs, limiting the maximum measurement precision possible with such facilities. This limitation is exacerbated in the next generation of infra-red based systems, as the number of modes supported by the fibre scales inversely with the wavelength squared and more modes typically equates to better scrambling. Substantial effort has been made by major research groups in this area to improve the fibre link performance by employing non-circular fibres, double scramblers, fibre shakers, and fibre stretchers. We present an original design of a multicore fibre (MCF) terminated with multimode photonic lantern ports. It is designed to act as a relay fibre with the coupling efficiency of a multimode fibre (MMF), modal stability similar to a single-mode fibre and low loss in a wide range of wavelengths (380 nm to 860 nm). It provides phase and amplitude scrambling to achieve a stable near field and far-field output illumination pattern despite input coupling variations, and low modal noise for increased stability for high signal-to-noise applications such as precision radial velocity (PRV) science. Preliminary results are presented for a 511-core MCF and compared with current state of the art octagonal fibre.

  20. Preparation of ultrafine poly (sodium 4-styrenesulfonate) fibres via ...

    Indian Academy of Sciences (India)

    The ultrafine poly (sodium 4-styrenesulfonate) (NaPSS) fibres have been prepared for the first time by electrospinning. The spinning solutions (NaPSS aqueous solutions) in varied concentrations were studied for electrospinning into ultrafine fibres. The results indicated that the smooth fibre could be formed when the ...

  1. Microstructure and Mechanical Properties of Aligned Natural Fibre Composites

    DEFF Research Database (Denmark)

    Rask, Morten

    Recently, there has been a great interest in developing and maturing natural fibre composites for structural applications. Natural fibres derived from plants such as flax and hemp have the potential to compete with traditional glass fibres as reinforcements in polymer matrices, due to good specific...

  2. Pectin Methylesterase and Pectin Remodelling Differ in the Fibre Walls of Two Gossypium Species with Very Different Fibre Properties

    Science.gov (United States)

    Liu, Qinxiang; Talbot, Mark; Llewellyn, Danny J.

    2013-01-01

    Pectin, a major component of the primary cell walls of dicot plants, is synthesized in Golgi, secreted into the wall as methylesters and subsequently de-esterified by pectin methylesterase (PME). Pectin remodelling by PMEs is known to be important in regulating cell expansion in plants, but has been poorly studied in cotton. In this study, genome-wide analysis showed that PMEs are a large multi-gene family (81 genes) in diploid cotton (Gossypium raimondii), an expansion over the 66 in Arabidopsis and suggests the evolution of new functions in cotton. Relatively few PME genes are expressed highly in fibres based on EST abundance and the five most abundant in fibres were cloned and sequenced from two cotton species. Their significant sequence differences and their stage-specific expression in fibres within a species suggest sub-specialisation during fibre development. We determined the transcript abundance of the five fibre PMEs, total PME enzyme activity, pectin content and extent of de-methylesterification of the pectin in fibre walls of the two cotton species over the first 25–30 days of fibre growth. There was a higher transcript abundance of fibre-PMEs and a higher total PME enzyme activity in G. barbadense (Gb) than in G. hirsutum (Gh) fibres, particularly during late fibre elongation. Total pectin was high, but de-esterified pectin was low during fibre elongation (5–12 dpa) in both Gh and Gb. De-esterified pectin levels rose thereafter when total PME activity increased and this occurred earlier in Gb fibres resulting in a lower degree of esterification in Gb fibres between 17 and 22 dpa. Gb fibres are finer and longer than those of Gh, so differences in pectin remodelling during the transition to wall thickening may be an important factor in influencing final fibre diameter and length, two key quality attributes of cotton fibres. PMID:23755181

  3. Design and evaluation of carbon fibre-reinforced launch packages with segmented, copper and molybdenum fibre armatures

    NARCIS (Netherlands)

    Koops, M.; Huijser, T.; Karthaus, W.

    1997-01-01

    Fibre armatures have been studied both dynamically and statically to gain insight in their electrothermal and mechanical behaviour. In the first part of this paper, the results of launch experiments with single and multi-segment copper and molybdenum fibre armatures integrated in carbon-fibre

  4. GLUT4 expression at the plasma membrane is related to fibre volume in human skeletal muscle fibres

    DEFF Research Database (Denmark)

    Gaster, M; Vach, W; Beck-Nielsen, H

    2002-01-01

    In this study we examined the relationship between GLUT4 expression at the plasma membrane and muscle fibre size in fibre-typed human muscle fibres by immunocytochemistry and morphometry in order to gain further insight into the regulation of GLUT4 expression. At the site of the plasma membrane...

  5. Influence of the physical structure of flax fibres on the mechanical properties of flax fibre reinforced polypropylene composites

    NARCIS (Netherlands)

    Oever, van den M.J.A.; Bos, H.L.; Kemenade, van M.J.J.M.

    2000-01-01

    This study investigates the influence of the physical structure of flax fibres on the mechanical properties of polypropylene (PP) composites. Due to their composite-like structure, flax fibres have relatively weak lateral bonds which are in particular present in flax fibres that are often used in

  6. New Insights into Muscle Fibre Types in Casertana Pig

    Directory of Open Access Journals (Sweden)

    Salvatore Velotto

    2010-01-01

    Full Text Available Little is known about the Casertana pig. The aim of this study was to evaluate the effect of sex on histochemical and morphometrical characteristics of muscle fibres (myocytes in this pure breed and to verify the presence of giant fibres as well as vascularity of the muscle. Finally, maximum shortening velocity and isometric tension were measured in single muscle fibres. Sixteen Casertana pigs (8 males, 8 females from a farm in Campania (Italy were slaughtered at one year of age. Muscle tissues were obtained from psoas minor, rhomboideus and longissimus dorsi. Myofibres were stained for myosin adenosine triphosphatase, succinic dehydrogenase, and α-amylase-periodic acid schiff. For all fibre types, the area and perimeter were measured. Slowtwitch oxidative fibres, fast-twitch glycolytic fibres and fast-twitch oxidative-glycolytic fibres were histochemically differentiated; an image-analyzing system was used. The results showed significant differences between the sexes in the size of all three fibre types. The psoas minor muscle had a high percentage of slow-twitch oxidative fibres and contained more capillaries per fibre and per mm2 than rhomboideus and longissimus dorsi, in which fast-twitch glycolytic fibres dominated. The cross-sectional area of all fibre types was larger in longissimus dorsi than in rhomboideus and psoas minor muscles; the giant fibres were present in the longissimus dorsi muscle only. Besides, isometric tension values were higher in fast-twitch glycolytic fibres than in the other ones. Variations in fibre type composition may contribute to meat quality.

  7. Influence of thermo-mechanical processing on the microstructure of Cu-based shape memory alloys produced by powder metallurgy

    International Nuclear Information System (INIS)

    Rodriguez, P.P.; Ibarra, A.; Iza-Mendia, A.; Recarte, V.; Perez-Landazabal, J.I.; San Juan, J.; No, M.L.

    2003-01-01

    Cu-Al-Ni shape memory alloys processed by powder metallurgy show very good thermo-mechanical properties, much better than those found in alloys produced by conventional casting. In this paper, we present the microstructural characterisation of these powder metallurgy alloys in order to find the microscopic mechanisms, linked to the powder metallurgy processing method, which are indeed responsible of such good thermo-mechanical behaviour. Electron microscopy studies [scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM)] show that powder metallurgy processing creates a sub-grain structure characterised by the presence of low angle sub-boundaries. These sub-boundaries are found to be lying on {1 1 0} and {1 1 2} lattice planes and are composed by an arrangement of superdislocations. These sub-boundaries may improve ductility in two ways: acting as a sink of dislocations which promotes plastic deformation and decreasing stress concentration at grain boundaries. Moreover, since sub-boundaries act as weak obstacles for the movement of martensite plates, the improvement on ductility is accomplished by an adequate thermo-mechanical behaviour

  8. Self-Paced Tutorial Courses for Mineral Science - Metallurgy Departments. Final Progress Report (July 1975-August 1980).

    Science.gov (United States)

    Twidwell, L. G.

    Four courses in extractive metallurgy (Pyrometallurgy, Hydrometallurgy, Electrometallurgy; and Physical Chemistry of Iron and Steel) were prepared in a modular, self-paced format. Development of the course materials included: (1) preparation of course outlines by unit coordinators and advisory committees; (2) approval of course outlines (included…

  9. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, S.

    1979-01-01

    This manual deals with the following subjects: plastic deformation of pure metals, yield strength in pure metals, work hardening in pure metals, hardening of solid solutions, recovery, recrystallization, crystal growth, creep, rupture and fatigue properties, metal transformations [fr

  10. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual, the following topics are discussed: thermodynamics of solid solutions, phase diagrams, properties of dilute solid solutions, structure of solid solutions, thermodynamics of surfaces, perfect dislocations, partial dislocations and stacking faults, interfaces, point defects

  11. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual the following topics are reviewed: macroscopic thermodynamics, statistical mechanics, quantum mechanics, cristallography, elasticity and anelasticity, and plastic deformation of a homogeneous medium [fr

  12. Physical metallurgy

    International Nuclear Information System (INIS)

    Adda, Y.; Dupouy, J.M.; Philibert, J.; Quere, Y.

    1976-01-01

    In this manual, the following topics are discussed: atomic vibrations, lattice thermal properties, chemical bonds, free electron model, band theory, properties of actinides, rare earths and transition metals, transport phenomena, magnetic properties, properties of liquid metals and amorphous state alloys

  13. Practical Metallurgy

    DEFF Research Database (Denmark)

    Bissacco, Giuliano; Deganello, Davide

    2003-01-01

    This is the report regards the activities carried out during the practical metatllurgy course concerning material properties and structures and their testing & analysis methods. During the course several aspects of the materials have been considered and different techniques have been analyzed....

  14. EFFECTS OF POLYTHENE FIBRES ON SELECTED PROPERTIES ...

    African Journals Online (AJOL)

    eobe

    Keywords: Compressive Strength, Polythene Fibre, Sandcrete Blocks, Tensile Strength. 1. INTRODUCTION. 1. INTRODUCTION. Sandcrete blocks are walling materials that are made of coarse natural sand ... as walling elements in structures; although used for centuries, still ... Bamboo wood waste can be used in making of ...

  15. Multimode supercontinuum generation in chalcogenide glass fibres

    DEFF Research Database (Denmark)

    Kubat, Irnis; Bang, Ole

    2016-01-01

    Mid-infrared supercontinuum generation is considered in chalcogenide fibres when taking into account both polarisations and the necessary higher order modes. In particular we focus on high pulse energy supercontinuum generation with long pump pulses. The modeling indicates that when only a single...

  16. Measuring method for optical fibre sensors

    NARCIS (Netherlands)

    Lammerink, Theodorus S.J.; Fluitman, J.H.J.

    1984-01-01

    A new measuring method for the signal amplitude in intensity modulating fibre optic sensors is described. A reference signal is generated in the time domain. The method is insensitive for the sensitivity fluctuations of the light transmitter and the light receiver. The method is experimentally

  17. Step index fibre using laser interferometer

    Indian Academy of Sciences (India)

    2014-03-04

    Mar 4, 2014 ... fibre of a nearly quadratic thickness variation is introduced between the two plates of the interfer- ometer. The obtained fringe shift shows a good agreement with the proposed quadratic model. The ... The radon function computes the line integrals from multiple sources along parallel paths, or beams,.

  18. Focused ion beam milling of carbon fibres

    International Nuclear Information System (INIS)

    Huson, Mickey G.; Church, Jeffrey S.; Hillbrick, Linda K.; Woodhead, Andrea L.; Sridhar, Manoj; Van De Meene, Allison M.L.

    2015-01-01

    A focused ion beam has been used to mill both individual carbon fibres as well as fibres in an epoxy composite, with a view to preparing flat surfaces for nano-indentation. The milled surfaces have been assessed for damage using scanning probe microscopy nano-indentation and Raman micro-probe analysis, revealing that FIB milling damages the carbon fibre surface and covers surrounding areas with debris of disordered carbon. The debris is detected as far as 100 μm from the milling site. The energy of milling as well as the orientation of the beam was varied and shown to have an effect when assessed by Raman spectroscopy. - Highlights: • Focused ion beam (FIB) milling was used to mill flat surfaces on carbon fibres. • Raman spectroscopy showed amorphous carbon was generated during FIB milling. • The amorphous debris is detected as far as 100 μm from the milling site. • This surface degradation was confirmed by nano-indentation experiments.

  19. Recycling of Aluminum from Fibre Metal Laminates

    NARCIS (Netherlands)

    Zhu, G.; Xiao, Y.; Yang, Y.; Wang, J.; Sun, B.; Boom, R.

    2012-01-01

    Recycling of aluminum alloy scrap obtained from delaminated fibre metal laminates (FMLs) was studied through high temperature refining in the presence of a salt flux. The aluminum alloy scrap contains approximately mass fraction w(Cu) = 4.4%, w(Mg) = 1.1% and w(Mn) = 0.6% (2024 aluminum alloy). The

  20. Microscopic Study on Hemp Bast Fibre Formation

    NARCIS (Netherlands)

    Hernandez, A.; Westerhuis, W.; Dam, van J.E.G.

    2007-01-01

    Commonly, fibre hemp (Cannabis sativa) is not considered for the production of soft and easy-care textiles. However, initial tests in the textile industry have shown that certain processes allow improvement in the everyday-wear characteristics of hemp textiles. In the framework of the EU R&D

  1. Step index fibre using laser interferometer

    Indian Academy of Sciences (India)

    2014-03-04

    Mar 4, 2014 ... the graded index fibres is shown referring to the corresponding tomographic image. Also, the tomographic cylinder shows a gross diameter related to the major axis of the ellipse compared to the small width at the ends of the cylinder indicating the minor axis of the cylinder. Pramana – J. Phys., Vol. 82, No.

  2. SILK FIBRE DEGRADATION AND ANALYSIS BY PROTEOMICS

    Directory of Open Access Journals (Sweden)

    YUKSELOGLU S.Muge

    2016-05-01

    Full Text Available Silk is one of the promising natural fibres and has a long established history in textile production throughout the centuries. Silk is produced by cultured silk worms, spiders, scorpions, mites and flies. It is extracellular proteinaceous fibres which consist of highly crystalline and insoluble proteins, the fibroins glued with sericin and an amourphous protein. On the other hand, understanding and controlling the degradation of protein materials are important for determining quality and the value of appearance retention in textiles. Hence, for silk textiles, appearance retention is critical value for the quality. And this is one of the key properties directly related to the degree and nature of protein degradation. It is therefore necessary to understand the silk composition and damage to obtain good conservation treatments and long-term preservation especially for the historical silk fabrics. In this study, silk fibre and its properties are briefly introduced along with images on their fibre damages. Additionally, proteomics method which helps to understand the degradation at the molecular level in textiles is introduced. Finally, proteomic evaluation of silk is summarized according to the researchers carried out in the literature.

  3. hollow fibre supported liquid membrane extraction of ...

    African Journals Online (AJOL)

    Preferred Customer

    ABSTRACT. ABSTRACT. A simple sample pre-treatment method utilizing hollow fibre supported liquid membrane. (HFSLM) was carried out on pharmaceuticals samples comprising of cough syrups (CS1 and CS2) and an anti- inflammatory product (AI). The active ingredients targeted in the extraction process were ...

  4. Thermally induced structural changes in Nomex fibres

    Indian Academy of Sciences (India)

    Unknown

    Meredith 1975). In this context, it is of interest to gain knowledge about the response of these fibres to thermal environments. Detailed analyses have been carried out in the past to identify the effect of thermal exposures on the initial characteristics of ...

  5. Control systems in optical fibre industry

    Czech Academy of Sciences Publication Activity Database

    Kostka, František

    1998-01-01

    Roč. 1, č. 4 (1998), s. 195-200 ISSN 1405-5546 Grant - others:AV ČR(CZ) KSK1067601 Projekt 10/96/K:4107 Keywords : control systems * real time systems * microcomputers * optical fibres Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  6. Scintillating fibre (SciFi) tracker

    CERN Multimedia

    Caraban Gonzalez, Noemi

    2017-01-01

    128 modules – containing 11 000 km of scintillating fibres – will make up the new SciFi tracker, which will replace the outer and inner trackers of the LHCb detector as part of the experiment’s major upgrade during Long Shutdown 2 (LS2)

  7. Hollow fibre supported liquid membrane extraction of ...

    African Journals Online (AJOL)

    A simple sample pre-treatment method utilizing hollow fibre supported liquid membrane (HFSLM) was carried out on pharmaceuticals samples comprising of cough syrups (CS1 and CS2) and an anti-inflammatory product (AI). The active ingredients targeted in the extraction process were diphenylhydramine (DPH), ...

  8. Fabrication of Polymer Optical Fibre (POF) Gratings.

    Science.gov (United States)

    Luo, Yanhua; Yan, Binbin; Zhang, Qijin; Peng, Gang-Ding; Wen, Jianxiang; Zhang, Jianzhong

    2017-03-04

    Gratings inscribed in polymer optical fibre (POF) have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

  9. Single Chromatin Fibre Assembly Using Optical Tweezers

    NARCIS (Netherlands)

    Bennink, Martin L.; Pope, L.H.; Leuba, S.H.; de Grooth, B.G.; Greve, Jan

    2001-01-01

    Here we observe the formation of a single chromatin fibre using optical tweezers. A single -DNA molecule was suspended between two micron-sized beads, one held by a micropipette and the other in an optical trap. The constrained DNA molecule was incubated with Xenopus laevis egg extract in order to

  10. Hybrid Composite Structures : Multifunctionality through Metal Fibres

    NARCIS (Netherlands)

    Ahmed, T.

    2009-01-01

    The introduction of fibre reinforced polymer composites into the wings and fuselages of the newest aircraft are changing the design and manufacturing approach. Composites provide greater freedom to designers who want to improve aircraft performance in an affordable way. In this quest, researchers

  11. Dietary fibre, glycaemic response, and diabetes.

    Science.gov (United States)

    Brennan, Charles S

    2005-06-01

    The much publicised global trend in rising levels of obesity and diabetes has refuelled interest in the dietary intake of the macronutrients (fat, protein, and carbohydrates) necessary to maintain the state of normalcy (good health) of an individual. Both scientific and public attention have focused on the dietary mediation of chronic health syndromes, either through use of dietary supplements, or a review of the whole diet situation. Dietary supplements have been used extensively both as pharmacological supplements, food ingredients, in processed foods to aid weight control, and the regulation of glucose control for diabetic patients. Particular interest has focused on the use of dietary fibres, especially soluble dietary fibres (such as guar gum, locust bean gum, and psyllium fibres), resistant starch, and slowly digestible carbohydrates. These have been shown to alter food structure, texture, and viscosity, and hence the rate of starch degradation during digestion. Research has also illustrated an association between the rate of carbohydrate degradation during digestion, and the regulation of postprandial blood sugar and insulin levels. The current paper explores the potential use of dietary fibres in the treatment of obesity and diabetes.

  12. Compressive Failure of Fibre Reinforced Materials

    DEFF Research Database (Denmark)

    Jensen, Henrik Myhre

    2003-01-01

    Compressive failure of uni-directional fibre composites by the kink band mechanism is analysed taking into account effects of residual stresses. Two criteria for determining the strength of the composite material have been investigated: Kink band formation at a bifurcation stress in a composite...

  13. Fibre inflation and α-attractors

    Science.gov (United States)

    Kallosh, Renata; Linde, Andrei; Roest, Diederik; Westphal, Alexander; Yamada, Yusuke

    2018-02-01

    Fibre inflation is a specific string theory construction based on the Large Volume Scenario that produces an inflationary plateau. We outline its relation to α-attractor models for inflation, with the cosmological sector originating from certain string theory corrections leading to α = 2 and α = 1/2. Above a certain field range, the steepening effect of higher-order corrections leads first to the breakdown of single-field slow-roll and after that to the onset of 2-field dynamics: the overall volume of the extra dimensions starts to participate in the effective dynamics. Finally, we propose effective supergravity models of fibre inflation based on an \\overline{D3} uplift term with a nilpotent superfield. Specific moduli dependent \\overline{D3} induced geometries lead to cosmological fibre models but have in addition a de Sitter minimum exit. These supergravity models motivated by fibre inflation are relatively simple, stabilize the axions and disentangle the Hubble parameter from supersymmetry breaking.

  14. Self-compacting fibre-reinforced concrete

    NARCIS (Netherlands)

    Grunewald, S.; Walraven, J.C.

    2001-01-01

    The project 'self-compacting fibre-reinforced concrete (SCFRC)' is part of the Dutch STW/PPM program - 'cement-bonded materials' - DCT.4010. Subproject III to which the project ,SCFRC' belongs deals with the development of new high performance concretes. The project 'SCFRC' aims at investigating the

  15. CERN selects Fujikura's radiation resistant fibre

    CERN Multimedia

    2007-01-01

    "Fujikura today announced that its radiation resistant single mode optical fibre has been selected by CERN, the European Laboratory for Particle Physics, to provide communication links within the world's largest particle accelerator - the Large hadron Collider (LHC) - near Genevan, Switzerland. (1/2 page)

  16. From nanoparticles to fibres: effect of dispersion composition on fibre properties

    Science.gov (United States)

    Schirmer, Katharina S. U.; Esrafilzadeh, Dorna; Thompson, Brianna C.; Quigley, Anita F.; Kapsa, Robert M. I.; Wallace, Gordon G.

    2015-06-01

    A polyvinyl alcohol (PVA)-stabilized polypyrrole nanodispersion has been optimised for conductivity and processability by decreasing the quantity of PVA before and after synthesis. A reduction of PVA before synthesis leads to the formation of particles with a slight increase in dry particle diameter (51 ± 6 to 63 ± 3 nm), and conversely a reduced hydrodynamic diameter. Conductivity of the dried nanoparticle films was not measureable after a reduction of PVA prior to synthesis. Using filtration of particles after synthesis, PVA content was sufficiently reduced to achieve dried thin film conductivity of 2 S cm-1, while the electroactivity of the dispersed particles remained unchanged. The as-synthesized and PVA-reduced polypyrrole particles were successfully spun into all-nanoparticle fibres using a wet-extrusion approach without the addition of any polymer or gel matrix. Using nanoparticles as a starting material is a novel approach, which allowed the production of macro-scale fibres that consisted entirely of polypyrrole nanoparticles. Fibres made from PVA-reduced polypyrrole showed higher electroactivity compared to fibres composed of the dispersion high in PVA. The mechanical properties of the fibres were also improved by reducing the amount of PVA present, resulting in a stronger, more ductile and less brittle fibre, which could find potential application in various fields.

  17. From nanoparticles to fibres: effect of dispersion composition on fibre properties

    Energy Technology Data Exchange (ETDEWEB)

    Schirmer, Katharina S. U.; Esrafilzadeh, Dorna; Thompson, Brianna C.; Quigley, Anita F.; Kapsa, Robert M. I.; Wallace, Gordon G., E-mail: gwallace@uow.edu.au [University of Wollongong, ARC Centre for Electromaterials Science and Intelligent Polymer Research Institute (Australia)

    2015-06-15

    A polyvinyl alcohol (PVA)-stabilized polypyrrole nanodispersion has been optimised for conductivity and processability by decreasing the quantity of PVA before and after synthesis. A reduction of PVA before synthesis leads to the formation of particles with a slight increase in dry particle diameter (51 ± 6 to 63 ± 3 nm), and conversely a reduced hydrodynamic diameter. Conductivity of the dried nanoparticle films was not measureable after a reduction of PVA prior to synthesis. Using filtration of particles after synthesis, PVA content was sufficiently reduced to achieve dried thin film conductivity of 2 S cm{sup −1}, while the electroactivity of the dispersed particles remained unchanged. The as-synthesized and PVA-reduced polypyrrole particles were successfully spun into all-nanoparticle fibres using a wet-extrusion approach without the addition of any polymer or gel matrix. Using nanoparticles as a starting material is a novel approach, which allowed the production of macro-scale fibres that consisted entirely of polypyrrole nanoparticles. Fibres made from PVA-reduced polypyrrole showed higher electroactivity compared to fibres composed of the dispersion high in PVA. The mechanical properties of the fibres were also improved by reducing the amount of PVA present, resulting in a stronger, more ductile and less brittle fibre, which could find potential application in various fields.

  18. REINFORCING FIBRES AS PART OF TECHNOLOGY OF CONCRETES

    Directory of Open Access Journals (Sweden)

    Zhukov Aleksey Dmitrievich

    2012-07-01

    It was identified that the basalt fibre consumption rate influences both the strength and the density of products made of cellular concrete. The length of the basalt fibre impacts the strength of products. A nomogram was developed to identify the consumption rate of the basalt fibre driven by the strength of products and the Portland cement consumption rate. The authors also studied the influence of the consumption rate of Portland cement and basalt fibre onto the structural quality ratio of the foamed fibre concrete.

  19. Natural Pineapple Leaf Fibre Extraction On Josapine And Morris

    OpenAIRE

    Mazalan Muhammad Firdaus; Yusof Yusri

    2017-01-01

    The pineapple’s leaf plant contains approximately 2.5% to 3.5% of strong white silky fibres. These fibres are useful and can be extracted from the leaves. There are a few ways to extract the fibre such as hand scrapping and by extraction machine. The objective of this research is to study the quality of fibre extraction by using different age of pineapple leaf. Next, the study aims to compare the quality of Josapine and Morris pineapple leaf with tensile test. Fibre yield percentage are calcu...

  20. Simple Room Temperature Method for Polymer Optical Fibre Cleaving

    DEFF Research Database (Denmark)

    Saez-Rodriguez, David; Nielsen, Kristian; Bang, Ole

    2015-01-01

    In this paper, we report on a new method to cleave polymer optical fibre. The most common way to cut a polymer optical fibre is chopping it with a razor blade; however, in this approach both the fibre and the blade must be preheated in order to turn the material ductile, and thus, prevent crazing....... In this paper, we make use of the temperature-time equivalence in polymers to replace the use of heating by an increase of the cleaving time and use a sawing motion to reduce fibre end face damage. In this way, the polymer fibre can be cleaved at room temperature in seconds with the resulting end face being...

  1. Sorption Properties of Steam Treated Wood and Plant Fibres

    DEFF Research Database (Denmark)

    Hoffmeyer, Preben; Jensen, Signe Kamp; Jones, Dennis

    2003-01-01

    Hygrothermal treatment of wood and plant fibres was carried out to improve the dimensional stability of the fibres and products made from these. Fibres of Norway spruce, beech, wheat and hemp were included. The efficiency of the treatment was assessed by studying the moisture sorption properties...... sorption sites. The annual plant fibres proved less susceptible than wood fibres to chemical breakdown from steam treatment. The component most susceptible to chemical breakdown was hemicellulose. Beech, wheat and hemp showed only a modest decrease of cellulose content, even at high temperatures, whereas...

  2. The carbon fibre market and uses for composite wind blades

    Energy Technology Data Exchange (ETDEWEB)

    Lowe, J.R. [Tenax Fibers Gmbh and Co. KG, Wuppertal (Germany)

    1996-09-01

    Due to its excellent fatigue properties, low weight and high stiffness, carbon fibre reinforced plastic (CFRP) is the ideal material to use for the manufacture of wind blades. The present use of CFRP in the wind energy sector however is very low in comparison to glass fibre reinforced plastic (GFRP) materials. The main reason for this low use of CFRP is cost since at present times carbon fibre is valued ten times as much as glass fibre. This paper introduces carbon fibre as an alternative material to glass and examines the use of CFRP components in other high fatigue applications. (au)

  3. Fibre Bragg Gratings in Embedded Microstructured Optical Fibres Allow Distinguishing between Symmetric and Anti-Symmetric Lamb Waves in Carbon Fibre Reinforced Composites.

    Science.gov (United States)

    De Pauw, Ben; Goossens, Sidney; Geernaert, Thomas; Habas, Dimitrios; Thienpont, Hugo; Berghmans, Francis

    2017-08-24

    Conventional contact sensors used for Lamb wave-based ultrasonic inspection, such as piezo-electric transducers, measure omnidirectional strain and do not allow distinguishing between fundamental symmetric and anti-symmetric modes. In this paper, we show that the use of a single fibre Bragg grating created in a dedicated microstructured optical fibre allows one to directly make the distinction between these fundamental Lamb wave modes. This feature stems from the different sensitivities of the microstructured fibre to axial and transverse strain. We fabricated carbon fibre-reinforced polymer panels equipped with embedded microstructured optical fibre sensors and experimentally demonstrated the strain waves associated with the propagating Lamb waves in both the axial and transverse directions of the optical fibre.

  4. Biological durability and oxidative potential of man-made vitreous fibres as compared to crocidolite asbestos fibres

    Energy Technology Data Exchange (ETDEWEB)

    Hippeli, S.; Dornisch, K.; Elstner, E.F. [Lehrstuhl fuer Phytopathologie, Technische Univ. Muenchen-Weihenstephan, Freising-Weihenstephan (Germany); Wiethege, T.; Mueller, K.M. [Berufsgenossenschaftliche Kliniken Bergmannsheil, Universitaetsklinik, Inst. fuer Pathologie, Bochum (Germany); Gillissen, A. [Medizinische Universitaetsklinik und Poliklinik II, Kardiologie, Pneumologie, Bonn (Germany)

    2001-08-01

    In this study we investigated relationships between redox properties and biodurability of crocidolite asbestos fibres and three different man-made vitreous fibres (MMVF): traditional stone wool fibres (MMVF 21), glass fibres (MMVF 11) and refractory ceramic fibres (RCF). Each fibre type was incubated up to 22 weeks in four different incubation media: gamble solution (GS) pH 5.0 and pH 7.4, representing blood plasma without proteins, and surfactant-like solution (SLS) pH 5.0 and pH 7.4. During incubation time aliquots of incubation mixtures were removed and analysed in a biochemical model reaction, mimicking activated phagocytes. In addition, changes of fibre morphology and chemical composition were examined using SEM- and EDX-technology. In the presence of crocidolite asbestos fibres and MMVF 21 the formation of OH-radicals according to the Haber-Weiss sequence could be demonstrated, whereas MMVF 11 and RCF showed no reactivity. Crocidolite asbestos fibres exhibited a significant higher activity compared with the stone wool fibres at the onset of incubation. The oxidative capacities of these fibre types were shown to depend on both specific surface area and iron content. The oxidative potentials of crocidolite asbestos fibres as well as MMVF 21 were not constant during incubation over several weeks in each incubation medium. The reactivities showed sinoidal curves including reactivities much higher than those at the onset of incubation time. These irregular changes of oxidative capacity may be explained by changes of the redox state of fibre surface-complexed iron. Furthermore our results showed clear differences between incubation of fibres in GS and SLS, respectively, indicating that phospholipids play an important part in fibre dissolution behaviour and oxidative reactivity. (orig.)

  5. Mechanical properties of thermoplastic composites reinforced with Entada Mannii fibre

    Directory of Open Access Journals (Sweden)

    Oluwayomi BALOGUN

    2017-06-01

    Full Text Available The mechanical properties and fracture mechanisms of thermoplastic composites reinforced with Entada mannii fibres was investigated. Polypropylene reinforced with 1, 3, 5, and 7 wt% KOH treated and untreated Entada mannii fibres were processed using a compression moulding machine. The tensile properties, impact strength, and flexural properties of the composites were evaluated while the tensile fracture surface morphology was examined using scanning electron microscopy. The results show that reinforcing polypropylene with Entada mannii fibres resulted in improvement of the tensile strength and elastic modulus. This improvement is remarkable for 5 wt% KOH treated Entada mannii fibre reinforced composites by 28 % increase as compared with the unreinforced polypropylene. The composites reinforced with Entada mannii fibres also had impact strength values of 70 % higher than the unreinforced polypropylene. However, the polypropylene reinforced with 5 and 7wt% KOH treated fibres exhibited significantly higher flexural strength and Young’s modulus by 53% and 52% increase as compared with the unreinforced polypropylene. The fracture surface of the polypropylene composites reinforced with untreated Entada mannii fibres were characterized by fibre debonding, fibre pull-out and matrix yielding while less voids and fibre pull-outs are observed in the composites reinforced with KOH treated Entada mannii fibres. v

  6. Effects of Basalt Fibres on Mechanical Properties of Concrete

    Directory of Open Access Journals (Sweden)

    El-Gelani A. M.

    2018-01-01

    Full Text Available This paper presents the results of an experimental program carried out to investigate the effects of Basalt Fibre Reinforced Polymers (BFRP on some fundamental mechanical properties of concrete. Basalt fibres are formed by heating crushed basalt rocks and funnelling the molten basalt through a spinneret to form basalt filaments. This type of fibres have not been widely used till recently. Two commercially available chopped basalt fibres products with different aspect ratios were investigated, which are dry basalt (GeoTech Fibre and basalt pre-soaked in an epoxy resin (GeoTech Matrix .The experimental work included compression tests on 96 cylinders made of multiple batches of concrete with varying amounts of basalt fibre additives of the two mentioned types, along with control batches containing no fibres. Furthermore, flexural tests on 24 prisms were carries out to measure the modulus of rupture, in addition to 30 prisms for average residual strength test. Results of the research indicated that use of basalt fibres has insignificant effects on compressive strength of plain concrete, where the increase in strength did not exceed about 5%. On the other hand, results suggest that the use of basalt fibres may increase the compressive strength of concrete containing fly as up top 40%. The rupture strength was increased also by 8% to 28% depending on mix and fibre types and contents. Finally, there was no clear correlation between the average residual strength and ratios of basalt fibres mixed with the different concrete batches.

  7. Turbulent stress measurements of fibre suspensions in a straight pipe

    Science.gov (United States)

    MacKenzie, Jordan; Söderberg, Daniel; Swerin, Agne; Lundell, Fredrik

    2018-02-01

    The focus of the present work is an experimental study of the behaviour of semi-dilute, opaque fibre suspensions in fully developed cylindrical pipe flows. Measurements of the normal and turbulent shear stress components and the mean flow were acquired using phase-contrast magnetic resonance velocimetry. Two fibre types, namely, pulp fibre and nylon fibre, were considered in this work and are known to differ in elastic modulus. In total, three different mass concentrations and seven Reynolds numbers were tested to investigate the effects of fibre interactions during the transition from the plug flow to fully turbulent flow. It was found that in fully turbulent flows of nylon fibres, the normal, ⟨uzuz ⟩ +, and shear, ⟨uzur ⟩ + (note that ⟨.⟩ is the temporal average, u is the fluctuating velocity, z is the axial or streamwise component, and r is the radial direction), turbulent stresses increased with Reynolds number regardless of the crowding number (a concentration measure). For pulp fibre, the turbulent stresses increased with Reynolds number when a fibre plug was present in the flow and were spatially similar in magnitude when no fibre plug was present. Pressure spectra revealed that the stiff, nylon fibre reduced the energy in the inertial-subrange with an increasing Reynolds and crowding number, whereas the less stiff pulp fibre effectively cuts the energy cascade prematurely when the network was fully dispersed.

  8. Analysis on fibre orientation of thermal bonded nonwoven

    Science.gov (United States)

    Musa, Atiyyah; Gong, Rong Hugh; Nasir, Eryna; Baharudin, Aznin; Tulos, Najua

    2016-02-01

    The aim of this research is to produce some three-dimensional (3D) nonwoven fabrics with variation in weight and type of fibre and then analyse their fibre orientation distribution by fast Fourier Transform (FFT) method. Three different fibres were used: polyester, polypropylene and blended polyester and polypropylene. Fabric weight varied from 20 to 180 g/m2. The processes of web formation and consolidation were based on the principle of air-laid and hot through-air thermal bonding technique. The result of the fibre orientation showed a random distribution of the fibres for all the samples. It indicated that there was no relationship between the variables and fibre orientation distribution. The position of 3D web whether from the top or side part did not show any variation and thus they did not have the influence towards the fibre orientation.

  9. High strength and low weight hollow carbon fibres

    Science.gov (United States)

    Köhler, T.; Brüll, R.; Pursche, F.; Langgartner, J.; Seide, G.; Gries, T.

    2017-10-01

    Carbon fibres have strengths of 2.5 to 5 GPa in the fibre direction and an elastic modulus of 200 to 500 GPa. Carbon fibres have equal mechanical properties as steel but 20% of the weight. But the material is more expensive than steel. Therefore, they are only used in industry sectors where the benefits legitimate the high costs. The use of hollow rather than solid fibres allows an even lower weight of the components. At the same time, similar mechanical properties are achieved by the circular cross section. Carbon fibres are obtained from polyacrylonitrile fibers (PAN). These can be produced as hollow fibres. As a first step stabilization and carbonization of hollow PAN precursors is investigated to produce hollow carbon fibres.

  10. Simplifying the design of microstructured optical fibre pressure sensors.

    Science.gov (United States)

    Osório, Jonas H; Chesini, Giancarlo; Serrão, Valdir A; Franco, Marcos A R; Cordeiro, Cristiano M B

    2017-06-07

    In this paper, we propose a way to simplify the design of microstructured optical fibres with high sensitivity to applied pressure. The use of a capillary fibre with an embedded core allows the exploration of the pressure-induced material birefringence due to the capillary wall displacements and the photoelastic effect. An analytical description of pressure-induced material birefringence is provided, and fibre modal characteristics are explored through numerical simulations. Moreover, a capillary fibre with an embedded core is fabricated and used to probe pressure variations. Even though the embedded-core fibre has a non-optimized structure, measurements showed a pressure sensitivity of (1.04 ± 0.01) nm/bar, which compares well with more complex, specially designed fibre geometries reported in the literature. These results demonstrate that this geometry enables a novel route towards the simplification of microstructured fibre-based pressure sensors.

  11. Natural Composites: Cellulose Fibres and the related Performance of Composites

    DEFF Research Database (Denmark)

    Lilholt, Hans; Madsen, Bo

    2014-01-01

    Biobased materials are becoming of increasing interest as potential structural materials for the future. A useful concept in this context is the fibre reinforcement of materials by stiff and strong fibres. The biobased resources can contribute with cellulose fibres and biopolymers. This offers...... the potential for stiff and strong biocomposite materials, but these have some limitations and obstacles to full performance. The focus will be on the ultra-structure, and the strength and stiffness of cellulose fibres, on the (unavoidable) defects causing large reductions in strength and moderate reductions...... in stiffness, on the packing ability of cellulose fibres and the related maximum fibre volume fraction in composites, on the moisture sorption of cellulose fibres and the related mass increase and (large) hygral strains induced, and on the mechanical performance of composites....

  12. Application of Microscopy and X-ray Diffraction in Optimization of the Production of NiTi Alloy by Powder Metallurgy

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Školáková, A.; Vojtěch, V.; Knaislová, A.; Pokorný, P.; Moravec, H.; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2014-01-01

    Roč. 14, č. 3 (2014), s. 387-392 ISSN 1213-2489. [Mezinárodní konference „Mikroskopie a nedestruktivní zkoušení materiálů/3./. Litoměřice, 22.10.2014-24.10.2014] R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : powder metallurgy * NiTi, * mechanical alloying * reactive sintering Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XIV_2014-3.pdf

  13. Compaction in optical fibres and fibre Bragg gratings under nuclear reactor high neutron and gamma fluence

    Energy Technology Data Exchange (ETDEWEB)

    Remy, L.; Cheymol, G. [CEA, French Nuclear Energy Commission, Nuclear Energy Division, DPC/SEARS/LISL Bat 467 CEA Saclay 91191 Gif/Yvette Cedex (France); Gusarov, A. [SCK.CEN - Belgian Nuclear Research center, Boeretang 200 2400 Mol (Belgium); Morana, A.; Marin, E.; Girard, S. [Universite de Saint-Etienne, Laboratoire Hubert Curien, UMR CNRS5516, 18, rue du Pr. Lauras, F-42000 Saint-Etienne (France)

    2015-07-01

    In the framework of the development by CEA and SCK.CEN of a Fabry Perot Sensor (FPS) able to measure dimensional changes in Material Testing Reactor (MTR), the first goal of the SAKE 1 (Smirnof extention - Additional Key-tests on Elongation of glass fibres) irradiation was to measure the linear compaction of single mode fibres under high fast neutron fluence. Indeed, the compaction of the fibre which forms one side of the Fabry Perot cavity, may in particular cause a noticeable measurement error. An accurate quantification of this effect is then required to predict the radiation-induced drift and optimize the sensor design. To achieve this, an innovative approach was used. Approximately seventy uncoated fibre tips (length: 30 to 50 mm) have been prepared from several different fibre samples and were installed in the SCK.CEN BR2 reactor (Mol Belgium). After 22 days of irradiation a total fast (E > 1 MeV) fluence of 3 to 5x10{sup 19} n{sub fast}/cm{sup 2}, depending on the sample location, was accumulated. The temperature during irradiation was 291 deg. C, which is not far from the condition of the intended FPS use. A precise measurement of each fibre tip length was made before the irradiation and compared to the post irradiation measurement highlighting a decrease of the fibres' length corresponding to about 0.25% of linear compaction. The amplitude of the changes is independent of the capsule, which could mean that the compaction effect saturates even at the lowest considered fluence. In the prospect of performing distributed temperature measurement in MTR, several fibre Bragg gratings written using a femtosecond laser have been also irradiated. All the gratings were written in radiation hardened fibres, and underwent an additional treatment with a procedure enhancing their resistance to ionizing radiations. A special mounting made it possible to test the reflection and the transmission of the gratings on fibre samples cut down to 30 to 50 mm. The comparison

  14. Some aspects of barreling in sintered plain carbon steel powder metallurgy preforms during cold upsetting

    Directory of Open Access Journals (Sweden)

    Sumesh Narayan

    2012-04-01

    Full Text Available The present research establishes a relationship of bulged diameter with densification and hydrostatic stress in forming of sintered iron (Fe powder metallurgy preforms cold upset under two different frictional conditions, namely, nil/no and graphite lubricant condition. Sintered plain carbon steel cylindrical preforms with carbon (C contents of 0, 0.35, 0.75 and 1.1% with constant initial theoretical density of 84% and aspect ratio of 0.4 and 0.6 were prepared using a suitable die-set assembly on a 1 MN capacity hydraulic press and sintered for 90 minutes at 1200 °C. Each sintered preform was cold upset under two different frictional constraints. It is seen that the degree of bulging reduces with reducing frictional constraints at the die contact surface. Further, it is found that the bulging ratio changed as a function of relative density and hydrostatic stress, respectively, according to the power law equations.

  15. Modeling of wear behavior of Al/B{sub 4}C composites produced by powder metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Sahin, Ismail; Bektas, Asli [Gazi Univ., Ankara (Turkey). Dept. of Industrial Design Engineering; Guel, Ferhat; Cinci, Hanifi [Gazi Univ., Ankara (Turkey). Dept. of Materials and Metallurgy Engineering

    2017-06-01

    Wear characteristics of composites, Al matrix reinforced with B{sub 4}C particles percentages of 5, 10,15 and 20 produced by the powder metallurgy method were studied in this study. For this purpose, a mixture of Al and B{sub 4}C powders were pressed under 650 MPa pressure and then sintered at 635 C. The analysis of hardness, density and microstructure was performed. The produced samples were worn using a pin-on-disk abrasion device under 10, 20 and 30 N load through 500, 800 and 1200 mesh SiC abrasive papers. The obtained wear values were implemented in an artificial neural network (ANN) model having three inputs and one output using feed forward backpropagation Levenberg-Marquardt algorithm. Thus, the optimum wear conditions and hardness values were determined.

  16. Modeling of wear behavior of Al/B4C composites produced by powder metallurgy

    International Nuclear Information System (INIS)

    Sahin, Ismail; Bektas, Asli; Guel, Ferhat; Cinci, Hanifi

    2017-01-01

    Wear characteristics of composites, Al matrix reinforced with B 4 C particles percentages of 5, 10,15 and 20 produced by the powder metallurgy method were studied in this study. For this purpose, a mixture of Al and B 4 C powders were pressed under 650 MPa pressure and then sintered at 635 C. The analysis of hardness, density and microstructure was performed. The produced samples were worn using a pin-on-disk abrasion device under 10, 20 and 30 N load through 500, 800 and 1200 mesh SiC abrasive papers. The obtained wear values were implemented in an artificial neural network (ANN) model having three inputs and one output using feed forward backpropagation Levenberg-Marquardt algorithm. Thus, the optimum wear conditions and hardness values were determined.

  17. Microstructure and microanalysis studies of copper-nickel-tin alloys obtained by conventional powder metallurgy processing

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Masson, T.J.; Vitor, E.; Abreu, C.D.; Marques, I.M., E-mail: fisica.cch@mackenzie.br [Universidade Presbiteriana Mackenzie (CCH), Sao Paulo, SP (Brazil). Centro de Ciencias e Humanidades; Silva, L.C.E. da, E-mail: jgcarrio@mackenzie.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    The aim of this paper was to analyze the microstructural development in samples of Cu-Ni-Sn alloys (weight %) obtained by powder metallurgy (P/M). The powders were mixed for 1/2 hour. After this, they were pressed, in a cold uniaxial pressing (1000 kPa). In the next step the specimens were sintered at temperatures varying from 650 up to 780 deg C under vacuum. Secondly, the samples were homogenized at 500 deg C for several special times. The alloys were characterized by optical microscopy, electrical conductivity and Vickers hardness. X-rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, densification parameter, hardness, macrostructures and microstructures of the samples. (author)

  18. A powder metallurgy austenitic stainless steel for application at very low temperatures

    CERN Document Server

    Sgobba, Stefano; Liimatainen, J; Kumpula, M

    2000-01-01

    The Large Hadron Collider to be built at CERN will require 1232 superconducting dipole magnets operating at 1.9 K. By virtue of their mechanical properties, weldability and improved austenite stability, nitrogen enriched austenitic stainless steels have been chosen as the material for several of the structural components of these magnets. Powder Metallurgy (PM) could represent an attractive production technique for components of complex shape for which dimension tolerances, dimensional stability, weldability are key issues during fabrication, and mechanical properties, ductility and leak tightness have to be guaranteed during operation. PM Hot Isostatic Pressed test plates and prototype components of 316LN-type grade have been produced by Santasalo Powdermet Oy. They have been fully characterized and mechanically tested down to 4.2 K at CERN. The fine grained structure, the absence of residual stresses, the full isotropy of mechanical properties associated to the low level of Prior Particle Boundaries oxides ...

  19. New evidence for prehistoric copper metallurgy in the vicinity of Bor

    Directory of Open Access Journals (Sweden)

    Kapuran Aleksandar

    2016-01-01

    Full Text Available The last three years of archaeological investigations at the site Ru`ana in Banjsko Polje, in the immediate vicinity of Bor, have provided new evidence regarding the role of non-ferrous metallurgy in the economy of the prehistoric communities of north-eastern Serbia. The remains of metallurgical furnaces and a large amount of metallic slags at two neighbouring sites in the mentioned settlement reveal that locations with many installations for the thermal processing of copper ore existed in the Bronze Age. We believe, judging by the finds of material culture, that metallurgical activities in this area also continued into the Iron Age and, possibly, into the 4th century AD. [Projekat Ministarstva nauke Republike Srbije, br. 177020: Archaeology of Serbia: Cultural identity, integration factors, technological processes and the role of the central Balkans in the development of European prehistory

  20. Annual report of the Metallurgy Division [for the] period ending December 1976

    International Nuclear Information System (INIS)

    Elayaperumal, K.; Gupta, C.K.; Mukhopadhyay, P.; Rao, S.V.K.

    1977-01-01

    An account of the work done in the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the calendar year 1976 is given. Some of the major achievements are: (1) production of boron carbide and boral sheet for the Trombay R-5 reactor under construction, (2) production of niobium metal for the manufacture of Zr-Nb-Cu alloy garter springs, (3) development of a process for graphite coating on zircaloy, (4) studies on structural and metal physics aspects of zirconium alloys and steels, (5) studies on the corrosion behaviour of zircaloy-2 as affected by the replacement of helium and stress corrosion cracking of zircaloy fuel tubes in iodine atmosphere and (6) production of high density UO 2 pellets with stable microstructures and sinterable magnesium oxide for MHD application. (M.G.B.)

  1. Encyclopedic dictionary bilingual English-Spanish of sciences: mining, chemistry, geology, metallurgy and environment

    International Nuclear Information System (INIS)

    Munoz Maradona, M.; Bellini, M.; Busleiman, M.

    2007-01-01

    This dictionary has been designed to satisfy scientists, researchers, technicians, interpreters, translators and students' needs in the areas of chemistry, geology, mining, metallurgy and environment for they find it necessary to have an English- Spanish encyclopedia on their sciences. It is a reliable book when looking for words that are normally not included in everyday dictionaries. It is now reaching the final revision stage with more than 15,000 entries. It includes scientific terms, chemical formulas of minerals and other elements, noticeable scientists' biographies, tables, graphics, and images so as to help readers' understanding. It is divided into three columns: the first one presents the English term and its area of concern; the second, the corresponding Spanish equivalent, and in the third, a suitable explanation.(author)

  2. Microstructure, mechanical behavior and biocompatibility of powder metallurgy Nb-Ti-Ta alloys as biomedical material.

    Science.gov (United States)

    Liu, Jue; Chang, Lin; Liu, Hairong; Li, Yongsheng; Yang, Hailin; Ruan, Jianming

    2017-02-01

    Microstructures, mechanical properties, apatite-forming ability and in vitro experiments were studied for Nb-25Ti-xTa (x=10, 15, 20, 25, 35at.%) alloys fabricated by powder metallurgy. It is confirmed that the alloys could achieve a relative density over 80%. Meanwhile, the increase in Ta content enhances the tensile strength, elastic modulus and hardness of the as-sintered alloys. When increasing the sintering temperatures, the microstructure became more homogeneous for β phase, resulting in a decrease in the modulus and strength. Moreover, the alloys showed a good biocompatibility due to the absence of cytotoxic elements, and were suitable for apatite formation and cell adhesion. In conclusion, Nb-25Ti-xTa alloys are potentially useful in biomedical applications with their mechanical and biological properties being evaluated in this work. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. 9th Mining and metallurgy international congress, Leon, 24-28 May 1994

    International Nuclear Information System (INIS)

    1994-01-01

    The 9th Mining and Metallurgy International Congress had 201 communications. These was articulated into 4th areas: 1.- Geological resources management and profit: 1.1- Geological and mining research on geologic resources. 1.2.- Non energetic mineral resources exploitation. 1.3- Hydro-geologic and geothermia resources. 1.4- Geologic resources and planning. 2.- Energy: 2.1.- Energetic mining.- 2.2 Oil and gas. 2.3.- Electricity production and distribution. 2.4.- Coal clean technologies. 2.5.- Energetic management. 3.- Material engineering: 3.1.- Minerallurgia and metallurgic processes. 3.2- Industrial minerals and ornamental 10cks. 3.3 .- Building materials. 3.4 Advanced technology materials. 4.- Environmental and territorial engineering in basic industry. 4.1.-Valuation of environmental impacts. 4.2.- Restoration engineering in mining. 4.3.- Effluent and residue engineering. 4.4.- Environmental management and clean technologies 4.5.- Natural and technological risks

  4. U3O8 from resin for powder-metallurgy fabrication of reactor fuel

    International Nuclear Information System (INIS)

    Mosley, W.C. Jr.

    1982-01-01

    A study was conducted to determine if cation exchange resin could be used to produce U 3 O 8 powder suitable for use in powder metallurgy fabrication of fuel tubes for production reactors at the Savannah River Plant (SRP). U 3 O 8 powders have been produced from three cation exchange resins: DOWEX (Dow Chemical Co.) 50W, AG (Bio-Rad Laboratories, Richmond, California) MP-50, and Bio-REX (Bio-Rad Laboratories, Richmond, California). This study included characterization of the thermal decomposition of uranium-loaded resins, measurement of properties of resin-based U 3 O 8 powders, and metallographic examination of U 3 O 8 -Al cores in extruded fuel tubes. Results to date show that AG MP-50 appears to be the best resin for producing U 3 O 8 powder suitable for the PM process. 20 figures

  5. Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

    Science.gov (United States)

    Chen, B.; Moon, S. K.; Yao, X.; Bi, G.; Shen, J.; Umeda, J.; Kondoh, K.

    2018-02-01

    The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.

  6. [The organization of the comprehensive prevention of urolithiasis among ferrous metallurgy workers].

    Science.gov (United States)

    Egorova, A M

    2009-01-01

    The purpose of study is to evaluate the effectiveness of the set of preventive measures as applied to 321 workers of basic ferrous metallurgy specialties (steel makers, mill men, hot metal shearers). During the clinical examination all the workers were divided on three groups: the workers without any pathology (11.83%, the first group), the workers with metabolic disorders only without urolitiasis (64.81%, the second group) and the workers with urolitiasis diagnosis approved by ultrasonography (23.36%, the third group). The effectiveness of rehabilitation measures was evaluated during half a year (diet therapy, drinking regimen, medicinal plants treatment). After the course of preventive measures was applied the overall health condition of most workers ameliorated and the number of workers with urolitiasis development risk factors reliably decreased up to 6-12%.

  7. Separating and recycling metals from mixed metallic particles of crushed electronic wastes by vacuum metallurgy.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2009-09-15

    During the treatment of electronic wastes, a crushing process is usually used to strip metals from various base plates. Several methods have been applied to separate metals from nonmetals. However, mixed metallic particles obtained from these processes are still a mixture of various metals, including some toxic heavy metals such as lead and cadmium. With emphasis on recovering copper and other precious metals, there have hitherto been no satisfactory methods to recover these toxic metals. In this paper, the criterion of separating metals from mixed metallic particles by vacuum metallurgy is built. The results show that the metals with high vapor pressure have been almost recovered completely, leading to a considerable reduction of environmental pollution. In addition, the purity of copper in mixed particles has been improved from about 80 wt % to over 98 wt %.

  8. An Overview of Internal Fixation Implant Metallurgy and Galvanic Corrosion Effects.

    Science.gov (United States)

    Koh, Justin; Berger, Aaron; Benhaim, Prosper

    2015-08-01

    Orthopedic and hand surgery implants for internal fixation of fractures have evolved substantially over the past 50 years. Newer metal compositions have been used, and new standards have been applied to older alloys, resulting in modern implants with unique physical properties and better clinical performances. Conventional wisdom has long dictated that implanting different metals should be avoided, but few guidelines exist regarding the safety of using in proximity implant systems of dissimilar metals. To better characterize the landscape of internal fixation implant metallurgy, we have compiled the recommendations and conclusions of the currently available and pertinent literature. Copyright © 2015 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

  9. Fabrication of homogeneously dispersed graphene/Al composites by solution mixing and powder metallurgy

    Science.gov (United States)

    Zeng, Xiang; Teng, Jie; Yu, Jin-gang; Tan, Ao-shuang; Fu, Ding-fa; Zhang, Hui

    2018-01-01

    Graphene-reinforced aluminum (Al) matrix composites were successfully prepared via solution mixing and powder metallurgy in this study. The mechanical properties of the composites were studied using microhardness and tensile tests. Compared to the pure Al alloy, the graphene/Al composites showed increased strength and hardness. A tensile strength of 255 MPa was achieved for the graphene/Al composite with only 0.3wt% graphene, which has a 25% increase over the tensile strength of the pure Al matrix. Raman spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy were used to investigate the morphologies, chemical compositions, and microstructures of the graphene and the graphene/Al composites. On the basis of fractographic evidence, a relevant fracture mechanism is proposed.

  10. [Evaluation and prognosis of occupational risk in workers of nonferrous metallurgy enterprises].

    Science.gov (United States)

    Shliapnikov, D M; Kostarev, V G

    2014-01-01

    The article deals with results of a priori and a posteriori evaluation of occupational risk for workers' health. Categories of a priori occupational risk for workers are estimated as high to very high (intolerable) risk. Findings are that work conditions in nonferrous metallurgy workshop result in upper respiratory tract diseases (medium degree of occupational conditionality). Increased prevalence of such diseases among the workers is connected with length of service. The authors revealed priority factors for occupationally conditioned diseases. A promising approach in occupational medicine is creation of methods to evaluate and forecast occupational risk, that enable to specify goal parameters for prophylactic measures. For example, modelling the risk of occupationally conditioned diseases via changes in exposure to occupational factor and length of service proved that decrease of chemical concentrations in air of workplace to maximally allowable ones lowers risk of respiratory diseases from 14 to 6 cases per year, for length of service of 5 years and population risk.

  11. Influence of alkali treatment and fibre length on mechanical properties of short Agave fibre reinforced epoxy composites

    International Nuclear Information System (INIS)

    Mylsamy, K.; Rajendran, I.

    2011-01-01

    Highlights: → New renewable and biodegradable Agave americana fibre. → The mechanical properties of alkali treated composites increase 10-15% to compare untreated composites. → The influence fibre length is contributing the strength of short fibre composites. → Future scope in light weight materials manufacture. -- Abstract: Composites based on short Agave fibres (untreated and alkali treated) reinforced epoxy resin using three different fibre lengths (3 mm, 7 mm and 10 mm length) are prepared by using hand lay up and compression mould technique. The materials were characterized in terms of tensile, compressive, flexural, impact, water absorption properties and machinability behaviour. All mechanical tests showed that alkali treated fibre composites withstand more fracture strain than untreated fibre composites. As evidenced by the dynamic mechanical analysis (DMA) tests, the thermo-mechanical properties of the composite with alkali treated Agave fibre were considerably good as alkali treatment had facilitated more sites of fibre resin interface. The machinability and atomic force microscope (AFM) studies were carried out to analyze the fibre-matrix interaction in untreated and alkali treated Agave fibre-epoxy composites.

  12. Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications

    Directory of Open Access Journals (Sweden)

    Matěj Březina

    2017-10-01

    Full Text Available Magnesium with its mechanical properties and nontoxicity is predetermined as a material for biomedical applications; however, its high reactivity is a limiting factor for its usage. Powder metallurgy is one of the promising methods for the enhancement of material mechanical properties and, due to the introduced plastic deformation, can also have a positive influence on corrosion resistance. Pure magnesium samples were prepared via powder metallurgy. Compacting pressures from 100 MPa to 500 MPa were used for samples’ preparation at room temperature and elevated temperatures. The microstructure of the obtained compacts was analyzed in terms of microscopy. The three-point bendisng test and microhardness testing were adopted to define the compacts’ mechanical properties, discussing the results with respect to fractographic analysis. Electrochemical corrosion properties analyzed with electrochemical impedance spectroscopy carried out in HBSS (Hank’s Balanced Salt Solution and enriched HBSS were correlated with the metallographic analysis of the corrosion process. Cold compacted materials were very brittle with low strength (up to 50 MPa and microhardness (up to 50 HV (load: 0.025 kg and degraded rapidly in both solutions. Hot pressed materials yielded much higher strength (up to 250 MPa and microhardness (up to 65 HV (load: 0.025 kg, and the electrochemical characteristics were significantly better when compared to the cold compacted samples. Temperatures of 300 °C and 400 °C and high compacting pressures from 300 MPa to 500 MPa had a positive influence on material bonding, mechanical and electrochemical properties. A compacting temperature of 500 °C had a detrimental effect on material compaction when using pressure above 200 MPa.

  13. Acoustical model of a Shoddy fibre absorber

    Science.gov (United States)

    Manning, John Peter

    Shoddy fibres or "Shoddies" are a mixture of post-consumer and post-industrial fibres diverted from textile waste streams and recycled into their raw fibre form. They have found widespread use as a raw material for manufacturing sound absorbers that include, but are not limited to: automotive, architectural and home appliance applications. The purpose of this project is to develop a simple acoustic model to describe the acoustic behaviour of sound absorbers composed primarily of Shoddy fibres. The model requires knowledge of the material's bulk density only. To date, these materials have not been the focus of much published research and acoustical designers must rely on models that were developed for other materials or are overly complex. For modelling purposes, an equivalent fluid approach is chosen to balance complexity and accuracy. In deriving the proposed model, several popular equivalent fluid models are selected and the required input parameters for each model identified. The models are: the model of Delaney and Bazley, two models by Miki, the model of Johnson in conjunction with the model of Champoux and Allard and the model of Johnson in conjunction with the model of Lafarge. Characterization testing is carried out on sets of Shoddy absorbers produced using three different manufacturing methods. The measured properties are open porosity, tortuosity, airflow resistivity, the viscous and thermal characteristic lengths and the static thermal permeability. Empirical relationships between model parameters and bulk density are then derived and used to populate the selected models. This yields several 'simplified' models with bulk density as the only parameter. The most accurate model is then selected by comparing each model's prediction to the results of normal incidence sound absorption tests. The model of Johnson-Lafarge populated with the empirical relations is the most accurate model over the range of frequencies considered (approx. 300 Hz - 4000 Hz

  14. Modified glass fibre reinforced polymer composites

    Science.gov (United States)

    Cao, Yumei

    A high ratio of strength to density and relatively low-cost are some of the significant features of glass fibre reinforced polymer composites (GFRPCs) that made them one of the most rapidly developed materials in recent years. They are widely used as the material of construction in the areas of aerospace, marine and everyday life, such as airplane, helicopter, boat, canoe, fishing rod, racket, etc. Traditionally, researchers tried to raise the mechanical properties and keep a high strength/weight ratio using all or some of the following methods: increasing the volume fraction of the fibre; using different polymeric matrix material; or changing the curing conditions. In recent years, some new techniques and processing methods were developed to further improve the mechanical properties of glass fibre (GF) reinforced polymer composite. For example, by modifying the surface condition of the GF, both the interface strength between the GF and the polymer matrix and the shear strength of the final composite can be significantly increased. Also, by prestressing the fibre during the curing process of the composite, the tensile, flexural and the impact properties of the composite can be greatly improved. In this research project, a new method of preparing GFRPCs, which combined several traditional and modern techniques together, was developed. This new method includes modification of the surface of the GF with silica particles, application of different levels of prestressing on the GF during the curing process, and the change of the fibre volume fraction and curing conditions in different sets of experiments. The results of the new processing were tested by the three-point bend test, the short beam shear test and the impact test to determine the new set of properties so formed in the composite material. Scanning electronic microscopy (SEM) was used to study the fracture surface of the new materials after the mechanical tests were performed. By taking advantages of the

  15. Crystal structure of raptor adenovirus 1 fibre head and role of the beta-hairpin in siadenovirus fibre head domains.

    Science.gov (United States)

    Nguyen, Thanh H; Ballmann, Mónika Z; Do, Huyen T; Truong, Hai N; Benkő, Mária; Harrach, Balázs; van Raaij, Mark J

    2016-06-22

    Most adenoviruses recognize their host cells via an interaction of their fibre head domains with a primary receptor. The structural framework of adenovirus fibre heads is conserved between the different adenovirus genera for which crystal structures have been determined (Mastadenovirus, Aviadenovirus, Atadenovirus and Siadenovirus), but genus-specific differences have also been observed. The only known siadenovirus fibre head structure, that of turkey adenovirus 3 (TAdV-3), revealed a twisted beta-sandwich resembling the reovirus fibre head architecture more than that of other adenovirus fibre heads, plus a unique beta-hairpin embracing a neighbouring monomer. The TAdV-3 fibre head was shown to bind sialyllactose. Raptor adenovirus 1 (RAdV-1) fibre head was expressed, crystallized and its structure was solved and refined at 1.5 Å resolution. The structure could be solved by molecular replacement using the TAdV-3 fibre head structure as a search model, despite them sharing a sequence identity of only 19 %. Versions of both the RAdV-1 and TAdV-3 fibre heads with their beta-hairpin arm deleted were prepared and their stabilities were compared with the non-mutated proteins by a thermal unfolding assay. The structure of the RAdV-1 fibre head contains the same twisted ABCJ-GHID beta-sandwich and beta-hairpin arm as the TAdV-3 fibre head. However, while the predicted electro-potential surface charge of the TAdV-3 fibre head is mainly positive, the RAdV-1 fibre head shows positively and negatively charged patches and does not appear to bind sialyllactose. Deletion of the beta-hairpin arm does not affect the structure of the raptor adenovirus 1 fibre head and only affects the stability of the RAdV-1 and TAdV-3 fibre heads slightly. The high-resolution structure of RAdV-1 fibre head is the second known structure of a siadenovirus fibre head domain. The structure shows that the siadenovirus fibre head structure is conserved, but differences in the predicted surface charge

  16. In vitro bacterial fermentation of tropical fruit fibres.

    Science.gov (United States)

    Vong, M H; Stewart, M L

    2013-09-01

    Tropical fruits such as mango, papaya, pineapple and banana are rich sources of dietary fibre. However, few studies have examined the potential physiological effects of fibre from these tropical fruits. The aim of this study was to characterise the fermentability of dietary fibre found in banana, papaya, pineapple and mango as an estimate of the physiological effects of consuming these fruits. Freeze-dried fruit was subjected to in vitro digestion to remove digestible carbohydrates. Digestion residues were freeze-dried prior to fermentation. In vitro fermentation was carried for 24 h under anaerobic conditions to simulate conditions in the large intestine. Gas volume, pH and short chain fatty acids (SCFAs) concentration were measured at 0, 4, 8, 12, and 24 h. SCFAs were analysed by gas chromatography. There was no gas production from 0 to 8 h time points for all samples. Mango fibre resulted in more gas at 12 and 24 h than pineapple, papaya and banana fibres. The slurry pH was significantly lower for mango fibre at 12 and 24 h compared to other samples. Mango fibre resulted in significantly more propionate at 8 h compared to papaya and pineapple fibres. Butyrate concentrations were only significantly different at 4 h. At 24 h total and individual SCFA production did not differ among samples. All fruit fibres were fermentable, with mango fibre being the most rapidly fermented. Additional work is necessary to confirm a benefit on digestive health.

  17. Strength and toughness of structural fibres for composite material reinforcement.

    Science.gov (United States)

    Herráez, M; Fernández, A; Lopes, C S; González, C

    2016-07-13

    The characterization of the strength and fracture toughness of three common structural fibres, E-glass, AS4 carbon and Kevlar KM2, is presented in this work. The notched specimens were prepared by means of selective carving of individual fibres by means of the focused ion beam. A straight-fronted edge notch was introduced in a plane perpendicular to the fibre axis, with the relative notch depth being a0/D≈0.1 and the notch radius at the tip approximately 50 nm. The selection of the appropriate beam current during milling operations was performed to avoid to as much as possible any microstructural changes owing to ion impingement. Both notched and un-notched fibres were submitted to uniaxial tensile tests up to failure. The strength of the un-notched fibres was characterized in terms of the Weibull statistics, whereas the residual strength of the notched fibres was used to determine their apparent toughness. To this end, the stress intensity factor of a fronted edge crack was computed by means of the finite-element method for different crack lengths. The experimental results agreed with those reported in the literature for polyacrylonitrile-based carbon fibres obtained by using similar techniques. After mechanical testing, the fracture surface of the fibres was analysed to ascertain the failure mechanisms. It was found that AS4 carbon and E-glass fibres presented the lower toughness with fracture surfaces perpendicular to the fibre axis, emanating from the notch tip. The fractured region of Kevlar KM2 fibres extended along the fibre and showed large permanent deformation, which explains their higher degree of toughness when compared with carbon and glass fibres. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'. © 2016 The Author(s).

  18. LiFi: transforming fibre into wireless

    Science.gov (United States)

    Yin, Liang; Islim, Mohamed Sufyan; Haas, Harald

    2017-01-01

    Light-fidelity (LiFi) uses energy-efficient light-emitting diodes (LEDs) for high-speed wireless communication, and it has a great potential to be integrated with fibre communication for future gigabit networks. However, by making fibre communication wireless, multiuser interference arises. Traditional methods use orthogonal multiple access (OMA) for interference avoidance. In this paper, multiuser interference is exploited with the use of non-orthogonal multiple access (NOMA) relying on successive interference cancellation (SIC). The residual interference due to imperfect SIC in practical scenarios is characterized with a proportional model. Results show that NOMA offers 5 -10 dB gain on the equivalent signal-to-interference-plus-noise ratio (SINR) over OMA. The bit error rate (BER) performance of direct current optical orthogonal frequency division multiplexing (DCO-OFDM) is shown to be significantly improved when SIC is used.

  19. Optical fibre sensing: a solution for industry

    Science.gov (United States)

    Sun, T.; Fabian, M.; Chen, Y.; Vidakovic, M.; Javdani, S.; Grattan, K. T. V.; Carlton, J.; Gerada, C.; Brun, L.

    2017-04-01

    Optical fibres have been explored widely for their sensing capability to meet increasing industrial needs, building on their success in telecommunications. This paper provides a review of research activities at City University of London in response to industrial challenges through the development of a range of fibre Bragg grating (FBG)-based sensors for transportation structural monitoring. For marine propellers, arrays of FBGs mapped onto the surface of propeller blades allow for capturing vibrational modes, with reference to simulation data. The research funded by EU Cleansky programme enables the development of self-sensing electric motor drives to support `More Electric Aircraft' concept. The partnership with Faiveley Brecknell Willis in the UK enables the integration of FBG sensors into the railway current-collecting pantographs for real-time condition monitoring when they are operating under 25kV conditions.

  20. Presynaptic calcium signalling in cerebellar mossy fibres

    DEFF Research Database (Denmark)

    Thomsen, Louiza Bohn; Jörntell, Henrik; Midtgaard, Jens

    2010-01-01

    affected burst firing in mossy fibres; this paired-pulse depression was reduced by GABA B antagonists. While our results indicated that a presynaptic rosette electrophysiologically functioned as a unit, topical GABA application showed that calcium signals in the branches of complex rosettes could......Whole-cell recordings were obtained from mossy fibre terminals in adult turtles in order to characterize the basic membrane properties. Calcium imaging of presynaptic calcium signals was carried out in order to analyse calcium dynamics and presynaptic GABA B inhibition. A tetrodotoxin (TTX......)-sensitive fast Na(+) spike faithfully followed repetitive depolarizing pulses with little change in spike duration or amplitude, while a strong outward rectification dominated responses to long-lasting depolarizations. High-threshold calcium spikes were uncovered following addition of potassium channel blockers...