Shear Bond Strength of Saliva Contaminated and Re-etched All-in-One Adhesive to Enamel

Directory of Open Access Journals (Sweden)

M. Khoroushi

2008-12-01

Full Text Available Objective: The aim of this study was to investigate the effect of phosphoric acid re-etching of an enamel surface treated via a one-bottle adhesive system on shear bond strength between resin composite and the enamelsurface in different stages of adhesive application.Materials and Methods: Extracted intact premolars (n=84 were divided into sevengroups (n=12. In the control group 1, the adhesive i-Bond was used according to the manufacturer's instructions, with nocontamination. In groups 2 to 4, the conditioned and saliva, contaminated enamel was blot dried only, rinsed,and blot dried, rinsed blot dried and re-etched, respectively. In groups 5, 6and 7 cured adhesive was contaminated with saliva and then rinsed and blot-dried, blot dried only and rinsed, blot-dried and re-etched respectively. In groups 3, 4, 6 and 7 the adhesive was reapplied. Afterward, Z100 compos-ite cylinders were bonded to the enamel surfaces. The samples were thermocycled (5°C and 55°C, 30 s, dwelling time: 10 s, 500 cycles. Finally, the samples were sheared using Dartec testing machine and shear bond strength data were subjected to one-way ANOVA analysis and Tukey's HSD test.Results: There were statistically significant differences among groups 1 and 5-7. The samples in groups 1 and 4 demonstrated higher bond strengths than those in the other groups.Conclusion: Using phosphoric acid etching may be effective, only where contamination occurs prior to curing of the adhesive. After curing of the adhesive, none of the methods in this study would be preferred.

Determination of bond energies by mass spectrometry. Some transition metal carbonyls

International Nuclear Information System (INIS)

Michels, G.D.

1979-01-01

Two groups of transition metal carbonyls have been studied, M(CO) 6 and M(CO) 5 CS complexes of the Group VIB metals and M 2 (CO) 10 complexes of the Group VIIB metals. Results for the hexacarbonyl complexes indicate that the measured fragmentation energies are in error by 0.25 +- 0.02 eV per CO produced. This is attributed to excitation of CO to the first vibrational state. Least-squares dissociation energies calculated from corrected data for M(CO) 5 CS complexes indicate that the M--CS bond is 3 to 4 times stronger than the M--CO bonds. Substitution of CS for CO in going from M(CO) 6 to M(CO) 5 CS weakens the remaining M--CO bonds by an average of 0.2 eV. Previously unreported MnTc(CO) 10 and TcRe(CO) 10 are prepared by halide substitution of Tc(CO) 5 Br and Re(CO) 5 Br with Mn(CO) 5 - and Tc(CO) 5 - , respectively. In the positive ion, metal and mixed-metal decacarbonyls are considered as (CO) 5 M + --M(CO) 5 complexes possessing five strong and five weak M--CO bonds. For Mn 2 (CO) 10 and Re 2 (CO) 10 , M + --M dissociation energies are 3.0 +- 0.1 and 4.0 +- 0.3 eV, respectively. These energies are 2.5 times greater than those reported for homolytic cleavage to M(CO) 5 + and M(CO) 5

Spontaneous growth of whiskers on RE-bearing intermetallic compounds of Sn-RE, In-RE, and Pb-RE

International Nuclear Information System (INIS)

Liu Meng; Xian Aiping

2009-01-01

A phenomenon of the whiskers growth on the bulk rare earth (RE)-intermetallic compounds of NdSn 3 , NdIn 3 , and LaPb 3 is reported. The whiskers formed spontaneously on all of the RE-intermetallic compounds after exposed to room ambience (21-28 deg. C/20-56% RH, relative humidity) for several days. Among the samples, the propensity of whisker growth for NdSn 3 is the strongest, on which the tin whiskers were flourishing and covered all of the surfaces after exposed to room ambience for 22 days; while LaPb 3 is the secondary and NdIn 3 is the last one. Observed by SEM, the whiskers were exhibited as different morphology, size, and number density. The XRD analysis confirms the existence of RE(OH) 3 after whiskers formed, also, the weight gain curve of the samples exposed to room ambience supports that a spontaneous chemical reaction of the RE-intermetallic compounds with water in room ambience takes place. In discussion, it is proposed that the fresh metal atoms released by the chemical reaction could be causative to result in nucleation and spontaneous growth of the whiskers, while the anisotropy of crystal structure could be a reason to understand the difference of the whisker growth behaviors between Sn and Pb.

Spontaneous growth of whiskers on RE-bearing intermetallic compounds of Sn-RE, In-RE, and Pb-RE

Energy Technology Data Exchange (ETDEWEB)

Liu Meng [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 72 Wenhua Road, Shenyang 110016 (China); Xian Aiping, E-mail: ap.xian@imr.ac.c [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 72 Wenhua Road, Shenyang 110016 (China)

2009-11-03

A phenomenon of the whiskers growth on the bulk rare earth (RE)-intermetallic compounds of NdSn{sub 3}, NdIn{sub 3}, and LaPb{sub 3} is reported. The whiskers formed spontaneously on all of the RE-intermetallic compounds after exposed to room ambience (21-28 deg. C/20-56% RH, relative humidity) for several days. Among the samples, the propensity of whisker growth for NdSn{sub 3} is the strongest, on which the tin whiskers were flourishing and covered all of the surfaces after exposed to room ambience for 22 days; while LaPb{sub 3} is the secondary and NdIn{sub 3} is the last one. Observed by SEM, the whiskers were exhibited as different morphology, size, and number density. The XRD analysis confirms the existence of RE(OH){sub 3} after whiskers formed, also, the weight gain curve of the samples exposed to room ambience supports that a spontaneous chemical reaction of the RE-intermetallic compounds with water in room ambience takes place. In discussion, it is proposed that the fresh metal atoms released by the chemical reaction could be causative to result in nucleation and spontaneous growth of the whiskers, while the anisotropy of crystal structure could be a reason to understand the difference of the whisker growth behaviors between Sn and Pb.

Evaluation of structural vacancies for 1/1-Al-Re-Si approximant crystals by positron annihilation spectroscopy

Science.gov (United States)

Yamada, K.; Suzuki, H.; Kitahata, H.; Matsushita, Y.; Nozawa, K.; Komori, F.; Yu, R. S.; Kobayashi, Y.; Ohdaira, T.; Oshima, N.; Suzuki, R.; Takagiwa, Y.; Kimura, K.; Kanazawa, I.

2018-01-01

The size of structural vacancies and structural vacancy density of 1/1-Al-Re-Si approximant crystals with different Re compositions were evaluated by positron annihilation lifetime and Doppler broadening measurements. Incident positrons were found to be trapped at the monovacancy-size open space surrounded by Al atoms. From a previous analysis using the maximum entropy method and Rietveld method, such an open space is shown to correspond to the centre of Al icosahedral clusters, which locates at the vertex and body centre. The structural vacancy density of non-metallic Al73Re17Si10 was larger than that of metallic Al73Re15Si12. The observed difference in the structural vacancy density reflects that in bonding nature and may explain that in the physical properties of the two samples.

Transport and re-deposition of limiter-released metal impurities

International Nuclear Information System (INIS)

Claasen, H.A.; Repp, H.

1983-01-01

The transport parallel B-vector and re-deposition of limiter- (or divertor-target-)released metal impurities in a given counter-streaming scrape-off layer plasma is studied analytically by using a kinetic approach. Electron impact ionization, Coulomb collisions with the hydrogen ions, and impurity ion acceleration in a pre-sheath electric field are accounted for. The friction and electric-field forces provide the driving forces for impurity re-cycling in front of the limiter. Both hydrogen ion sputtering and self-sputtering are included (the latter for impurity emission perpendicular to the limiter surface). The analytical formulas are numerically evaluated for the example of sputtered iron impurities, assuming a simple model for a scrape-off layer plasma in contact with a stainless-steel poloidal ring limiter. (author)

Pt, Re and Pt-Re incorporation in sulfated zirconia as catalysts for n-pentane isomerization

International Nuclear Information System (INIS)

Aboul-Gheit, A.K.; El-Desouki, D.S.; Abdel-Hamid, S.M.; Ghoneim, S.A.; Ibrahim, A.H.; Gad, F.K.; Abdel-Aleem, G.M.

2010-01-01

Two groups of modified Sulfated Zirconia (S Z) catalysts were prepared by the sol-gel method. The first group was modified by four different concentrations of Pt metal (0.15, 0.30, 0.45 and 0.60 wt %), whereas the second group contained Pt-Re combinations on SZ. All the prepared catalysts were characterized by XRD, TPR, TEM, TGA, IR spectroscopy as well as surface properties using the BET method. The catalytic activity of the catalysts was examined for the hydro isomerization of n-pentane to iso-pentane. The catalytic activity was found to increase with increasing Pt concentration in the mono metallic catalysts. The combination of Re ion with Pt on SZ results in significant changes in the characters and activities of the catalysts. The 0.45 wt % Pt + 0.15 wt % Re/SZ catalyst exhibited the highest selective compared to other metal ratios investigated

All-electron study of ultra-incompressible superhard material ReB2: structural and electronic properties

International Nuclear Information System (INIS)

Yan-Ling, Li; Guo-Hua, Zhong; Zhi, Zeng

2009-01-01

This paper investigates the structural and electronic properties of rhenium diboride by first-principles calculation based on density functional theory. The obtained results show that the calculated equilibrium structural parameters of ReB 2 are in excellent agreement with experimental values. The calculated bulk modulus is 361 GPa in comparison with that of the experiment. The compressibility of ReB 2 is lower than that of well-known OsB 2 . The anisotropy of the bulk modulus is confirmed by c/a ratio as a function of pressure curve and the bulk modulus along different axes along with the electron density distribution. The high bulk modulus is attributed to the strong covalent bond between Re-d and B-p orbitals and the wider pseudogap near the Fermi level, which could be deduced from both electron charge density distribution and density of states. The band structure and density of states of ReB 2 exhibit that this material presents metallic behavior. The good metallicity and ultra-incompressibility of ReB 2 might suggest its potential application as pressure-proof conductors. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Electronic structures and properties of the rhenium alkoxy derivatives Re2O3(OMe)6, Re4O6(OMe)12, and ReMoO2(OMe)7

International Nuclear Information System (INIS)

Ermakov, A.I.; Belousov, V.V.; Drobot, D.V.; Shcheglov, P.A.

2006-01-01

The geometrical structures, charge distributions, dipole moments, frequencies of normal vibrations, NMR spectra, and total energies of the chemical bonds for the rhenium alkoxy derivatives Re 2 O 3 (OMe) 6 , Re 4 O 6 (OMe) 12 , and ReMoO 2 (OMe) 7 were calculated by the DFT-B3LYP and Hartree-Fock ab initio methods based on the effective core potential theory (LANL2DZ approximation) and the semiempirical PM3(tm) method. Two optimized structures of Re 2 O 3 (OMe) 6 with close energies were found to substantially differ in geometry, 1 H, 13 C, and 17 O NMR spectra, and dipole moment. Various characteristics of the electronic structures and the trans-effect of the ligands in the compounds under consideration were discussed [ru

Developments with melt spun RE-Fe-B powder for bonded magnets

International Nuclear Information System (INIS)

Brown, D.N.; Chen, Z.; Guschl, P.; Campbell, P.

2006-01-01

Rapidly quenched isotropic rare earth iron boride (RE-Fe-B) powders have found many applications throughout the electronics, automotive and white goods industries. The magnetic performance, thermal stability, corrosion resistance and processability of a powder are important factors when selecting a RE-Fe-B powder for a particular application. For electronic devices that operate at ambient temperatures, high remanence (B r ) tends to be a priority and RE 2 Fe 14 B/α-Fe nanocomposite powder magnets are favoured. Alternatively, automotive applications tend to require greater thermal stability and corrosion resistance, which are satisfied by single-phase RE 2 Fe 14 B powder magnets with higher intrinsic coercivity (H ci ). This article reviews the performance of commercially available rapidly solidified RE-Fe-B powders and recent developments made to address the demands of applications

Production of {sup 186}Re and {sup 188}Re, and synthesis of {sup 188}Re-DTPA

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, Kazuyuki; Motoishi, Shoji; Kobayashi, Katsutoshi; Izumo, Mishiroku [Department of Radioisotopes, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Musdja, Muhammad Yanis

1999-08-01

Production of radioactive rhenium isotopes {sup 186}Re and {sup 188}Re, and synthesis of {sup 188}Re-DTPA have been studied. For {sup 186}Re, a production method by the {sup 185}Re(n, {gamma}) {sup 186}Re reaction in a reactor has been established. For {sup 188}Re, a production method by the double neuron capture reaction of {sup 186}W, which produces a {sup 188}W/{sup 188}Re generator, has been established. For synthesis of {sup 188}Re-DTPA, the optimum conditions, including pH, the amounts of regents and so on, have been determined. (author)

Re-telling, Re-evaluating and Re-constructing

Directory of Open Access Journals (Sweden)

Gorana Tolja

2013-11-01

Full Text Available 'Graphic History: Essays on Graphic Novels and/as History '(2012 is a collection of 14 unique essays, edited by scholar Richard Iadonisi, that explores a variety of complex issues within the graphic novel medium as a means of historical narration. The essays address the issues of accuracy of re-counting history, history as re-constructed, and the ethics surrounding historical narration.

Re-OPCAB vs. Re-CABG for myocardial revascularization.

Science.gov (United States)

Schütz, A; Mair, H; Wildhirt, S M; Gillrath, G; Lamm, P; Kilger, E; Reichart, B

2001-06-01

The present study compared redo coronary artery bypass grafting (Re-OPCAB) techniques with conventional redo coronary artery bypass grafting (Re-CABG) with particular focus on myocardial damage and clinical outcome parameters. Redo OPCAB (Re-OPCAB) was performed on 20 consecutive patients (15 males, mean age 63.2 +/- 9.3 years) using either the anterolateral approach for minimally invasive direct coronary artery bypass (n = 4) or the Octopus technique with regular sternotomy (n = 16). The Re-CABG group consisted of 20 consecutive patients (18 males, mean age 67.1 +/- 6.6 years). Groups did not differ in the number of atherosclerotic risk factors, or left ventricular, renal or liver function. Duration of surgery, number of bypass grafts and amount of transfused red blood cells did not differ significantly between both groups. Requirement of epinephrine (mg/h) within the first 24 h was lower in the Re-OPCAB group (Re-OPCAB: 0.14 +/- 0.22 vs. CABG: 0.88 +/- 0.97; p<0.01). In addition, CKMB levels at 24 h after operation were lower in the Re-OPCAB group (Re-OPCAB: 10.0 +/- 10.1 vs. Re-CABG: 38.7 +/- 28.1 U/l, p<0.001). There were no acute myocardial infarctions or deaths in the perioperative period. In the CABG group, there was a longer time period to extubation (hours) (Re-OPCAB: 9.8 +/- 3.9 vs. Re-CABG: 28.7 +/- 25.5; p<0.001), and the length of ICU stay was significantly prolonged (OPCAB: 1.3 +/- 0.5 versus Re-CABG: 4.4 +/- 8.7; p<0.001). The graft patency rate at follow-up was 95% in the Re-OPCAB group. Re-OPCAB results in decreased cardiac specific enzyme release, reduced requirement of inotropes and comparable clinical outcome in the early postoperative period. It is an appropriate alternative to conventional Re-CABG in selected patients awaiting reoperation for myocardial revascularization. Larger prospective and randomized trials are required to select the appropriate patient who benefits most from one or the other treatment regime.

Excimer laser assisted re-oxidation of BaTiO3 thin films on Ni metal foils

International Nuclear Information System (INIS)

Bharadwaja, S. S. N.; Ko, S. W.; Qu, W.; Clark, T.; Rajashekhar, A.; Motyka, M.; Podraza, N.; Randall, C. A.; Trolier-McKinstry, S.

2016-01-01

Excimer laser assisted re-oxidation for reduced, crystallized BaTiO 3 thin films on Ni-foils was investigated. It was found that the BaTiO 3 can be re-oxidized at an oxygen partial pressure of ∼50 mTorr and substrate temperature of 350 °C without forming a NiO x interface layer between the film and base metal foil. The dielectric permittivity of re-oxidized films was >1000 with loss tangent values <2% at 100 Hz, 30 mV rms excitation signal. Electron Energy Loss Spectroscopy indicated that BaTiO 3 thin films can be re-oxidized to an oxygen stoichiometry close to ∼3 (e.g., stoichiometric). High resolution cross sectional transmission electron microscopy showed no evidence of NiO x formation between the BaTiO 3 and the Ni foil upon excimer laser re-oxidation. Spectroscopic ellipsometry studies on laser re-oxidized [001] C and [111] C BaTiO 3 single crystals indicate that the re-oxidation of BaTiO 3 single crystals is augmented by photo-excitation of the ozone, as well as laser pulse induced temperature and local stress gradients

Effect of Re-Application of Microbrush on Micro Tensile Bond Strength of an Adhesive to Dentin

Directory of Open Access Journals (Sweden)

Seied Majid Mosavi Nasab

2013-02-01

Full Text Available Background and Aims: Re-application of microbrush may affect the micro tensile bond strength of adhesives to dentin. The aim of this study was to evaluate the effect of re-application of microbrushes on the micro tensile bond strength of an adhesive to dentin.Materials and Methods: Thirty freshly extracted molars teeth were collected and enamel of occlusal surface were removed to expose superficial dentin. Then superficial dentin was etched, washed and partially air dried.According to the times of application of microbrush, teeth were divided into two test groups. In group 1, newmicrobrushs were used, but in group 2, the ones that were already used for twice were included. Ambar dentin bonding agent (FGM/Brazil was applied to the etched dentin with microbrushes according to the manufacturer’s instructions. Then the crown of teeth was built up with LLiss (FGM/Brazil composite resin. The teeth were sectioned in buccolingual direction to obtain 1mm slabs. Then 50 hourglass- shape samples were made from 30 teeth (25 Specimens per group. The microtensile bond strength of the specimens was tested using MTD500 (SD Mechatronik, Germany. The data were statistically analyzed by T-test.Results: The mean values for the microtensile bond strength were 30.49±7.18 and 23.61±9.06 MPa±SD for the first and second groups, respectively. There was significant difference between the groups (P=0.005.Conclusion: Microbrushes should not be used for more than one cavity preparation.

Rhenium Re

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for determining rhenium in various objects are presented. The gravimetric determination of rhenium is based on a quantitative precipitation of ReO 4 - ions with tetraphenylarsonium chloride. The determination is not hindered by tungstates and molybdates. The potentiometric determination of rhenium in alloys (>=0.5% Re) is based on perrhenate ion reduction to Re(4) with the titrated solution of the Cr(2) salt. Re(7) is titrated in a hot sulfuric acid solution in the presence of KJ. The relative error of the method is 1 to 3%. The photometric determination of rhenium is performed by the rhodamide method in molybdenum-and tungsten-containing alloys and catalytically, in rocks, after it has been separated in the form of sulfide. The extraction-photometric determination of rhenium is carried out with the aid of methyl violet (analysis of a stock with a high content of Mo, W, Ta, Nb, Ti ahd Zr) and thio-oxine (the determination of Re is hindered by Au, Pt, Pd, Ru, Os, Rh, Ir). Also described are methods for differential-spectrophotometric determination of Re with the aid of thiocarbamide, as well as with the aid of dimethylglyoxime in the presence of SnCl 2 in an acid medium when Re is determined in its alloys with niobium and hafnium. It takes 2 hours to analyze the Hf-Re alloy and 3 hours to analyze the Nb-Re alloy, the standard deviation being 0.005 at 30-50% Re and 0.027 to 0.019 at 10-50% Re

Coherent Control of Nanoscale Ballistic Currents in Transition Metal Dichalcogenide ReS2.

Science.gov (United States)

Cui, Qiannan; Zhao, Hui

2015-04-28

Transition metal dichalcogenides are predicted to outperform traditional semiconductors in ballistic devices with nanoscale channel lengths. So far, experimental studies on charge transport in transition metal dichalcogenides are limited to the diffusive regime. Here we show, using ReS2 as an example, all-optical injection, detection, and coherent control of ballistic currents. By utilizing quantum interference between one-photon and two-photon interband transition pathways, ballistic currents are injected in ReS2 thin film samples by a pair of femtosecond laser pulses. We find that the current decays on an ultrafast time scale, resulting in an electron transport of only a fraction of one nanometer. Following the relaxation of the initially injected momentum, backward motion of the electrons for about 1 ps is observed, driven by the Coulomb force from the oppositely moved holes. We also show that the injected current can be controlled by the phase of the laser pulses. These results demonstrate a new platform to study ballistic transport of nonequilibrium carriers in transition metal dichalcogenides.

Partitioning of metals in a degraded acid sulfate soil landscape: influence of tidal re-inundation.

Science.gov (United States)

Claff, Salirian R; Sullivan, Leigh A; Burton, Edward D; Bush, Richard T; Johnston, Scott G

2011-11-01

The oxidation and acidification of sulfidic soil materials results in the re-partitioning of metals, generally to more mobile forms. In this study, we examine the partitioning of Fe, Cr, Cu, Mn, Ni and Zn in the acidified surface soil (0-0.1 m) and the unoxidised sub-soil materials (1.3-1.5 m) of an acid sulfate soil landscape. Metal partitioning at this acidic site was then compared to an adjacent site that was previously acidified, but has since been remediated by tidal re-inundation. Differences in metal partitioning were determined using an optimised six-step sequential extraction procedure which targets the "labile", "acid-soluble", "organic", "crystalline oxide", "pyritic" and "residual" fractions. The surficial soil materials of the acidic site had experienced considerable losses of Cr, Cu, Mn and Ni compared to the underlying parent material due to oxidation and acidification, yet only minor losses of Fe and Zn. In general, the metals most depleted from the acidified surface soil materials exhibited the greatest sequestration in the surface soil materials of the tidally remediated site. An exception to this was iron, which accumulated to highly elevated concentrations in the surficial soil materials of the tidally remediated site. The "acid-soluble", "organic" and "pyritic" fractions displayed the greatest increase in metals following tidal remediation. This study demonstrates that prolonged tidal re-inundation of severely acidified acid sulfate soil landscapes leads to the immobilisation of trace metals through the surficial accumulation of iron oxides, organic material and pyrite. Copyright © 2011 Elsevier Ltd. All rights reserved.

Phase stability, electronic, elastic and thermodynamic properties of Al-RE intermetallics in Mg-Al-RE alloy: A first principles study

Directory of Open Access Journals (Sweden)

H.L. Chen

2015-09-01

Full Text Available Electronic structure and elastic properties of Al2Y, Al3Y, Al2Gd and Al3Gd phases were investigated by means of first-principles calculations from CASTEP program based on density functional theory (DFT. The ground state energy and elastic constants of each phase were calculated, the formation enthalpy (ΔH, bulk modulus (B, shear modulus (G, Young's modulus (E, Poisson's ratio (ν and anisotropic coefficient (A were derived. The formation enthalpy shows that Al2RE is more stable than Al3RE, and Al-Y intermetallics have stronger phase stability than Al-Gd intermetallics. The calculated mechanical properties indicate that all these four intermetallics are strong and hard brittle phases, it may lead to the similar performance when deforming due to their similar elastic constants. The total and partial electron density of states (DOS, Mulliken population and metallicity were calculated to analyze the electron structure and bonding characteristics of the phases. Finally, phonon calculation was conducted, and the thermodynamic properties were obtained and further discussed.

Composition and local bonding in RE-Si-M-O-N (M=Mg, Al ; RE=La, Lu) glasses

Energy Technology Data Exchange (ETDEWEB)

Fouquet-Parry, V. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France); Paumier, F. [Laboratoire de Metallurgie Physique - UMR 6630 CNRS, Department of Materials Sciences, University of Poitiers (France); Guittet, M.J. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France); Gautier-Soyer, M. [Service de Physique et de Chimie des Surfaces et des Interfaces, DSM/DRECAM/SPCSI, CEA Saclay, 91191 Gif sur Yvette Cedex (France)], E-mail: mgautiersoyer@cea.fr; Satet, R.; Hoffmann, M.J. [Institut fuer Keramik im Maschinenbau, Universitaet Karlsruhe (Thailand), Haid-und-Neu-Strasse 7, D 76131 Karlsruhe (Germany); Becher, P.F.; Painter, G.S. [Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2008-05-30

Two series of oxynitride glasses, RE-Si-Mg-O-N (M=Mg, Al ; RE=La, Lu), have been studied by X-Ray photoelectron spectroscopy (XPS). The oxygen 1s photoelectron lineshape reveals a striking difference depending on the rare earth, both in the Mg series and in the Al series. Specifically, the oxygen 1s photoelectron lines of the La doped glasses are broader than the ones of the Lu doped glasses. This result is an experimental evidence that Lu has a larger affinity for oxygen versus nitrogen than La, as theoretically predicted by the first-principles calculations by Painter et al.

Nuclear fuel re-processing plant

International Nuclear Information System (INIS)

Sasaki, Yuko; Honda, Takashi; Shoji, Saburo; Kobayashi, Shiro; Furuya, Yasumasa

1989-01-01

In a nuclear fuel re-processing plant, high Si series stainless steels not always have sufficient corrosion resistance in a solution containing only nitric acid at medium or high concentration. Further, a method of blowing NOx gases may possibly promote the corrosion of equipment constituent materials remarkably. In view of the above, the corrosion promoting effect of nuclear fission products is suppressed without depositing corrosive metal ions as metals in the nitric acid solution. That is, a reducing atmosphere is formed by generating NOx by electrolytic reduction thereby preventing increase in the surface potential of stainless steels. Further, an anode is disposed in the nitric acid solution containing oxidative metal ions to establish an electrical conduction and separate them by way of partition membranes and a constant potential or constant current is applied while maintaining an ionic state so as not to deposit metals. Thus, equipments of re-processing facility can be protected from corrosion with no particular treatment for wastes as radioactive materials. (K.M.)

Adsorption and dissociation of dinitrogen on transition metal (Ta, W and Re) doped MgO surface

KAUST Repository

Yadav, Manoj Kumar; Vovusha, Hakkim; Sanyal, Biplab

2016-01-01

The adsorption and dissociation of dinitrogen on transition metal (Ta, W and Re) doped MgO(100) surface has been studied employing density functional theory. It is found that all these transition metals (TM) on MgO(100) surface are capable

Behavior of Re and Os during contact between an aqueous solution and oil: Consequences for the application of the Re-Os geochronometer to petroleum

Science.gov (United States)

Mahdaoui, Fatima; Michels, Raymond; Reisberg, Laurie; Pujol, Magali; Poirier, Yannick

2015-06-01

Several recent studies have raised the exciting possibility that oils can be dated using the Re-Os radioisotope system. However the exact nature of the events dated by this technique often remains unclear. Geochronologic interpretation of Re-Os data for oils is hampered by our limited knowledge of how these metals behave in petroleum systems. In particular, it is difficult to understand how isotopic homogenization, an essential prerequisite for the development of an isochronal relationship, can be achieved at the scale of a petroleum basin. The mechanisms capable of fractionating the Re/Os ratio in a suite of oils are also poorly understood. For this reason, we have performed an experimental study aimed at investigating the behavior of Re and Os during a particularly widespread phenomenon in petroleum systems, the interaction of formation waters with oils during migration. Contact experiments between natural oils and aqueous solutions enriched in Re and/or Os were carried out for varying lengths of time (6 h to 5 months), at different temperatures (25-150 °C), over a wide range of metal concentrations in the enriched solution (0.001-100 μg/g for Re; 1 and 10 ng/g for Os). In addition, the effect of oil composition on Re-Os exchange at the water-oil interface was examined by testing two oils with very different properties. All of our results demonstrate that Re and Os are transferred massively and very rapidly from the aqueous solution to the organic phase. This is true regardless of temperature or oil composition. It is also true for a very wide range of metal concentrations in the aqueous solution, up to an apparent saturation level that exceeds natural concentrations in oils by several orders of magnitude. Given the efficiency of Re and Os transfer from water to oil demonstrated here, and assuming that our findings are applicable to natural conditions, water/oil ratios of only about 250 would be needed to explain the Re and Os contents of most oils, based on

Hydrogen-induced structural transition in single layer ReS2

Science.gov (United States)

Yagmurcukardes, M.; Bacaksiz, C.; Senger, R. T.; Sahin, H.

2017-09-01

By performing density functional theory-based calculations, we investigate how structural, electronic and mechanical properties of single layer ReS2 can be tuned upon hydrogenation of its surfaces. It is found that a stable, fully hydrogenated structure can be obtained by formation of strong S-H bonds. The optimized atomic structure of ReS2H2 is considerably different than that of the monolayer ReS2 which has a distorted-1T phase. By performing phonon dispersion calculations, we also predict that the Re2-dimerized 1T structure (called 1T {{}\\text{R{{\\text{e}}2}}} ) of the ReS2H2 is dynamically stable. Unlike the bare ReS2 the 1T {{}\\text{R{{\\text{e}}2}}} -ReS2H2 structure which is formed by breaking the Re4 clusters into separated Re2 dimers, is an indirect-gap semiconductor. Furthermore, mechanical properties of the 1T {{}\\text{R{{\\text{e}}2}}} phase in terms of elastic constants, in-plane stiffness (C) and Poisson ratio (ν) are investigated. It is found that full hydrogenation not only enhances the flexibility of the single layer ReS2 crystal but also increases anisotropy of the elastic constants.

Formation of a Six-Coordinate fac-[Re(Co)3]+ Complex by the N-C bond cleavage of a potentially tetradentate ligand

International Nuclear Information System (INIS)

Booysen, I.; Gerber, T. I. A.; Hosten, E.; Mayer, P.

2008-01-01

The rhenium(I) compound fac-[Re(CO) 3 (daa)]. Hpab.H 2 O (Hpab N,N'-(l,2-phenylene)bis(2'-aminobenzamide); Hdaa 2-amino-N-(2-aminophenyl)benzamide) was synthesized from the reaction of [Re(CO) 5 ,Br] with two equivalent of Hpab in toluene. The monoanionic tridentate ligand daa was formed by the rhenium-mediated cleavage of an amido N-C bond of the potentially tetradentate ligand Hpab. The compound was characterized by IR spectroscopy and X-ray crystallography, and daa is coordinated as a diamino amide via three nitrogen-donor atoms

Radioanalysis of RE enrichment of ion adsorption type RE ores

CERN Document Server

Zhao Shu Quan; Hu He Ping; Li Fu Sheng; Chen Ying Min; LiuShiMing

2002-01-01

Objective: To analyze the radioactivity in Rare Earth (RE) enrichment of ion adsorption type RE ores. Methods: Using HPGe-gamma spectrometer to analyze the activity ratio of gamma radionuclides in kind of samples, using FJ-2603 low background alpha, beta measurement apparatus to measure their total alpha and total beta activities, and using X-ray fluorescence spectrometer to analyze contents of La sub 2 O sub 3 and Y sub 2 O sub 3 , respectively. Results: HPGe gamma spectroscopy and X-ray fluorescence spectroscopy are simple, convenient and non-destructive methods of analyzing radionuclides and La sub 2 O sub 3 , Y sub 2 O sub 3 in RE enrichment of ion adsorption type RE ores, respectively. Conclusion: The basic data were provided for radiation protection and treatment of gas, liquid and solid waste in RE production of ion adsorption type RE ores; method and experience were provided for studying ion adsorption type RE ores

MoRe-based and NbN-based tunnel junctions and their characteristics

International Nuclear Information System (INIS)

Shaternik, V.E.; Noskov, V.L.; Chubatyy, V.V.; Larkin, S.Yu.; Sizontov, V.M.; Miroshnikov, A.M.; Karmazin, A.A.

2007-01-01

Full text: Perspective [1] Josephson Mo-Re alloy-oxide-Pb, Mo-Re alloy-normal metal-oxide-Pb and Mo-Re alloy-normal metal-oxide- normal metal-Mo-Re alloy junctions have been fabricated and investigated. Thin (∼50-100 nm) MoRe superconducting films are deposited on Al 2 O 3 substrates by using a dc magnetron sputtering of MoRe target. Normal metal (Sn, Al) thin films are deposited on the MoRe films surfaces by thermal evaporation of metals in vacuum and oxidized to fabricate junctions oxide barriers. Quasiparticle I-V curves of the fabricated junctions were measured in wide range of voltages. To investigate a transparency spread for the fabricated junctions barriers the computer simulation of the measured quasiparticle I-V curves have been done in framework of the model of multiple Andreev reflections in double-barrier junction interfaces. It's demonstrated the investigated junctions can be described as highly asymmetric double-barrier Josephson junctions with great difference between the two barrier transparencies [2,3]. The result of the comparison of experimental quasiparticle I-V curves and calculated ones is proposed and discussed. Results of computer simulation of quasiparticles I-V curves of NbN-based junctions are presented and discussed. Also I-V curves of the fabricated junctions have been measured under microwave irradiation with 60 GHz frequency , clear Shapiro steps in the measured I-V curves were observed and discussed. (authors)

Electronic structures of ReS2, ReSe2 and TcS2 in the real and the hypothetical undistorted structures

NARCIS (Netherlands)

Fang, CM; Wiegers, GA; Haas, C; deGroot, RA

1997-01-01

The transition-metal dichalcogenides ReX2 (X = Sor Se) and TcS2 with a d(3) electron configuration have distorted; CdCl2 and Cd(OH)(2) structures, respectively, with the Re(Tc) atoms in each layer forming parallelogram-shaped connected clusters (diamond chain). Ab-initio band-structure calculations

Indides RE{sub 3}T{sub 2}In{sub 4} (RE = Y, Gd-Tm, Lu; T = Ni, Ru, Rh) with a ZrNiAl superstructure

Energy Technology Data Exchange (ETDEWEB)

Heying, Birgit; Niehaus, Oliver; Rodewald, Ute C.; Poettgen, Rainer [Univ. Muenster (Germany). Inst. fuer Anorganische und Analytische Chemie

2016-07-01

Three series of rare earth-transition metal-indides RE{sub 3}T{sub 2}In{sub 4} (RE=Y, Gd-Tm, Lu; T=Ni, Ru, Rh) were synthesized from arc-melted RE{sub 3}T{sub 2} precursor compounds and indium tear shot in sealed niobium ampoules using different annealing sequences. The new indides crystallize with the hexagonal Lu{sub 3}Co{sub 2}In{sub 4}-type structure, space group P anti 6. All samples were characterized on the basis of Guinier powder patterns and six structures were refined from single crystal X-ray diffractometer data. The RE{sub 3}T{sub 2}In{sub 4} structures are derived from the ZrNiAl type through RE/In ordering, paralleled by a symmetry reduction from P anti 62m to P anti 6. This induces twinning for some of the investigated crystals. The main crystal chemical motifs of the RE{sub 3}T{sub 2}In{sub 4} structures are trigonal prisms of rare earth, respectively indium atoms that are filled by the transition metals.

Strain induced optical properties of BaReO3

Science.gov (United States)

Kumavat, Sandip R.; Kansara, Shivam; Gupta, Sanjeev K.; Sonvane, Yogesh

2018-05-01

Here, we have performed strain induce optical properties of BaReO3 by using density functional theory (DFT). We noticed that after applying intrinsic and extrinsic strain to the BaReO3, it shows the metallic behavior. We also studied optical properties, which show good activity in the ultraviolet region. The results show that after applying intrinsic and extrinsic strain to BaReO3 the absorption peaks are shifted towards the high UV region of the spectrum. Thus, we concluded that, BaReO3 material with extrinsic strain can be useful for high frequency UV device and optoelectronic devices.

Effects of annealing on the microstructure, corrosion resistance, and mechanical properties of RE{sub 65}Co{sub 25}Al{sub 10} (RE=Ce, La, Pr, Sm, and Gd) bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhou [School of Materials Science and Engineering, University of Jinan, No. 336, West Road of Nan Xinzhuang, Jinan 250022 (China); Shandong Provincial Key Laboratory of Preparation and Measurement of Building Materials, University of Jinan, No. 336, West Road of Nan Xinzhuang, Jinan 250022 (China); Xing, Qi; Sun, Zhenxi; Xu, Jing; Zhao, Zhengfeng [School of Materials Science and Engineering, University of Jinan, No. 336, West Road of Nan Xinzhuang, Jinan 250022 (China); Chen, Shuying; Liaw, Peter K. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, TN (United States); Wang, Yan, E-mail: mse_wangy@ujn.edu.cn [School of Materials Science and Engineering, University of Jinan, No. 336, West Road of Nan Xinzhuang, Jinan 250022 (China); Shandong Provincial Key Laboratory of Preparation and Measurement of Building Materials, University of Jinan, No. 336, West Road of Nan Xinzhuang, Jinan 250022 (China)

2015-02-25

The effects of annealing on the microstructure, corrosion resistance and mechanical properties of the RE{sub 65}Co{sub 25}Al{sub 10} (RE=Ce, La, Pr, Sm, and Gd) bulk metallic glasses (BMGs) were studied. Microstructural changes are induced after annealing below the onset crystallization temperature of 484 K, resulting in the variation of thermal stability and crystallization behavior. A proper annealing enhances the corrosion resistance in 3.5 wt% NaCl solution, which can be attributed to reduction of the electrochemical activity and galvanic coupling effects in the chloride solution. Moreover, the RE-based BMG annealed at 484 K possesses the higher corrosion potential and lower corrosion current density, combined with the corrosion morphologies, which suggests the best corrosion resistance. Annealing can also obviously change the mechanical properties and fracture morphologies. It presents that free volume annihilation can cause more difficulty in the elastic atom rearrangement for the as-annealed RE-based BMGs.

Hydrocarbons dating by Re-Os method: experimental study of the Re-Os couple geochemical behaviour in oils during the evolution of a petroleum system

International Nuclear Information System (INIS)

Mahdaoui, Fatima

2013-01-01

The Re-Os radiogenic system is well adapted to the dating of oils and bitumen. However the meaning of the obtained age is ambiguous. This is mainly due to gaps in our knowledge of the geochemical behavior and the speciation of Re and Os in oils. Specifically, use of the Re-Os geo-chronometer requires an understanding of how Re-Os behavior can lead to the fulfillment of the conditions necessary for the development of an isochron. These conditions are: i) the isotopic homogenization of oils at the scale of a petroleum field ii) the fractionation of Re from Os so as to obtain samples with various Re/Os ratios iii) the closure of the system during the period of radiogenic ingrowth of the daughter isotope, that is, from the time of the event of interest to the present day. Experimental investigation of the organic geochemical behavior of Re and Os in oils under various conditions, designed as analogs of the different stages of petroleum generation and evolution, were performed in order to evaluate the use of the Re-Os system as a geo-chronometer in the context of a direct use on petroleum. The possibility of Re-Os fractionation resulting from asphaltene loss during oil evolution was investigated by sequential asphaltene precipitation in the laboratory. This study determined that Re and Os are mainly located in the most polar asphaltene fractions, that is, in the first to precipitate. This study also demonstrated that Re/Os ratios are not disturbed by asphaltene loss during the evolution of oils, unless this loss is unrealistically large. Thus asphaltene precipitation during migration and emplacement is not responsible for the Re/Os fractionation required for the use of the geo-chronometer. The possibility of metal transfer from formation waters to petroleum was studied by performing contact experiments between oils and aqueous solutions of Re and Os of various concentrations over a wide range of temperatures and for varying periods of time. This study demonstrated a

Relativistic Effects on Metal-Metal Bonding. Comparison of the Performance of ECP and Scalar DKH Description on the Picture of Metal-Metal Bonding in Re2Cl8(2-)

Czech Academy of Sciences Publication Activity Database

Ponec, Robert; Bučinský, L.; Gatti, C.

2010-01-01

Roč. 6, č. 10 (2010), s. 3113-3121 ISSN 1549-9618 R&D Projects: GA ČR GA203/09/0118 Grant - others:VEGA(SK) 1/0817/08; VEGA(SK) 1/0127/09; APVV(SK) 0093-07 Institutional research plan: CEZ:AV0Z40720504 Keywords : relativistic effects * metal-metal bonding Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 5.138, year: 2010

Surface studies of Os Re W alloy-coated impregnated tungsten cathodes

International Nuclear Information System (INIS)

Ares Fang, C.S.; Maloney, C.E.

1990-01-01

Impregnated tungsten cathodes half-coated with Re/W (or Os/W) alloy and Os Re W alloy at right angles were studied to compare the effects of Os Re W alloy coatings on the electron emission and emission mechanisms. Constant surface metal compositions of 32% Os--29% Re--39% W and 35% Os--26% Re--39% W were obtained from the activated surfaces initially coated with 40% Os--40% Re--20% W and 35% Os--45% Re--20% W alloys, respectively. Thermionic emission microscopy measurements showed that the Os Re W alloy-coated surface gives an average effective work function of 0.29, 0.08, and 0.03 eV lower than the uncoated, Re/W and Os/W alloy-coated surfaces. An effective work function of 1.73 eV was obtained from an activated Os Re W alloy surface. Auger studies exhibited a smaller BaO coverage and a higher barium coverage in excess of BaO stoichiometry on the Os Re W alloy-coated surface compared to the uncoated, Re/W and Os/W alloy-coated surfaces

Multiple C-H Bond Activations and Ring-Opening C-S Bond Cleavage of Thiophene by Dirhenium Carbonyl Complexes.

Science.gov (United States)

Adams, Richard D; Dhull, Poonam; Tedder, Jonathan D

2018-06-14

The reaction of Re 2 (CO) 8 (μ-C 6 H 5 )(μ-H) (1) with thiophene in CH 2 Cl 2 at 40 °C yielded the new compound Re 2 (CO) 8 (μ-η 2 -SC 4 H 3 )(μ-H) (2), which contains a bridging σ-π-coordinated thienyl ligand formed by the activation of the C-H bond at the 2 position of the thiophene. Compound 2 exhibits dynamical activity on the NMR time scale involving rearrangements of the bridging thienyl ligand. The reaction of compound 2 with a second 1 equiv of 1 at 45 °C yielded the doubly metalated product [Re 2 (CO) 8 (μ-H)] 2 (μ-η 2 -2,3-μ-η 2 -4,5-C 4 H 2 S) (3), formed by the activation of the C-H bond at the 5 position of the thienyl ligand in 2. Heating 3 in a hexane solvent to reflux transformed it into the ring-opened compound Re(CO) 4 [μ-η 5 -η 2 -SCC(H)C(H)C(H)][Re(CO) 3 ][Re 2 (CO) 8 (μ-H)] (4) by the loss of one CO ligand. Compound 4 contains a doubly metalated 1-thiapentadienyl ligand formed by the cleavage of one of the C-S bonds. When heated to reflux (125 °C) in an octane solvent in the presence of H 2 O, the new compound Re(CO) 4 [η 5 -μ-η 2 -SC(H)C(H)C(H)C(H)]Re(CO) 3 (5) was obtained by cleavage of the Re 2 (CO) 8 (μ-H) group from 4 with formation of the known coproduct [Re(CO) 3 (μ 3 -OH)] 4 . All new products were characterized by single-crystal X-ray diffraction analyses.

Design and assembly of ternary Pt/Re/SnO2 NPs by controlling the zeta potential of individual Pt, Re, and SnO2 NPs

Science.gov (United States)

Drzymała, Elżbieta; Gruzeł, Grzegorz; Pajor-Świerzy, Anna; Depciuch, Joanna; Socha, Robert; Kowal, Andrzej; Warszyński, Piotr; Parlinska-Wojtan, Magdalena

2018-05-01

In this study Pt, Re, and SnO2 nanoparticles (NPs) were combined in a controlled manner into binary and ternary combinations for a possible application for ethanol oxidation. For this purpose, zeta potentials as a function of the pH of the individual NPs solutions were measured. In order to successfully combine the NPs into Pt/SnO2 and Re/SnO2 NPs, the solutions were mixed together at a pH guaranteeing opposite zeta potentials of the metal and oxide NPs. The individually synthesized NPs and their binary/ternary combinations were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning transmission electron microscopy (STEM) combined with energy dispersive X-ray spectroscopy (EDS) analysis. FTIR and XPS spectroscopy showed that the individually synthesized Pt and Re NPs are metallic and the Sn component was oxidized to SnO2. STEM showed that all NPs are well crystallized and the sizes of the Pt, Re, and SnO2 NPs were 2.2, 1.0, and 3.4 nm, respectively. Moreover, EDS analysis confirmed the successful formation of binary Pt/SnO2 and Re/SnO2 NP, as well as ternary Pt/Re/SnO2 NP combinations. This study shows that by controlling the zeta potential of individual metal and oxide NPs, it is possible to assemble them into binary and ternary combinations. [Figure not available: see fulltext.

Phase formation in systems Re-Se-Br-MBr (M=Li, Na, K, Rb, Cs

International Nuclear Information System (INIS)

Yarovoj, S.S.; Mironov, Yu.V.; Tkachev, S.V.; Fedorov, V.E.

2009-01-01

Phase formation in the systems Re-Se-Br-MBr (M=K, Rb, Cs) has been studied by NMR-spectroscopy and X-ray phase analysis. Polymer complexes Re 6 Se 8 Br 2 and M 2 Re 6 Se 8 Br 4 (M=Cs, Rb), and salts containing cluster anions [Re 6 Se 6 Br 8 ] 2- and [Re 6 Se 7 Br 7 ] 3- are the main products of reactions occurring in molten alkali metal halides in the number of cluster anions [{Re 6 Se 8-n Br n }Br 6 ] (4-n)- (0≤n≤4). Effect of alkali metal cation on the composition and ratios of formed products is established

Adaptive prostate IGRT combining online re-optimization and re-positioning: a feasibility study

International Nuclear Information System (INIS)

Li Taoran; Zhu Xiaofeng; Lee, W Robert; Vujaskovic, Zeljko; Yin Fangfang; Wu, Q Jackie; Thongphiew, Danthai

2011-01-01

In prostate radiation therapy, inter-fractional organ motion/deformation has posed significant challenges on reliable daily dose delivery. To correct for this issue, off-line re-optimization and online re-positioning have been used clinically. In this paper, we propose an adaptive images guided radiation therapy (AIGRT) scheme that combines these two correction methods in an anatomy-driven fashion. The AIGRT process first tries to find a best plan for the daily target from a plan pool, which consists of the original CT plan and all previous re-optimized plans. If successful, the selected plan is used for daily treatment with translational shifts. Otherwise, the AIGRT invokes the re-optimization process of the CT plan for the anatomy of the day, which is afterward added to the plan pool as a candidate for future fractions. The AIGRT scheme is evaluated by comparisons with daily re-optimization and online re-positioning techniques based on daily target coverage, organs at risk (OAR) sparing and implementation efficiency. Simulated treatment courses for 18 patients with re-optimization alone, re-positioning alone and AIGRT shows that AIGRT offers reliable daily target coverage that is highly comparable to daily re-optimization and significantly improves from re-positioning. AIGRT is also seen to provide improved OAR sparing compared to re-positioning. Apart from dosimetric benefits, AIGRT in addition offers an efficient scheme to integrate re-optimization to current re-positioning-based IGRT workflow.

Theoretical analysis of hydrogen chemisorption on Pd(111), Re(0001) and PdML/Re(0001), ReML/Pd(111) pseudomorphic overlayers

DEFF Research Database (Denmark)

Pallassana, Venkataraman; Neurock, Matthew; Hansen, Lars Bruno

1999-01-01

not appear to provide an independent parameter for assessing surface reactivity. The weak chemisorption of hydrogen on the Pd-ML/Re(0001) surface relates to substantial lowering of the d-band center of Pd, when it is pseudomorphically deposited as a monolayer on a Re substrate. [S0163-1829(99)00331-2].......Gradient-corrected density-functional theory (DFT-GGA) periodic slab calculations have been used to analyze the binding of atomic hydrogen on monometallic Pd(111), Re(0001), and bimetallic Pd-mL/Re(0001) [pseudomorphic monolayer of Pd(111) on Re(0001)] and Re-ML/Pd(111) surfaces. The computed...

Crystal structure of R.E. NiSn and R.E. PdSn equiatomic compounds

International Nuclear Information System (INIS)

Dwight, A.E.

1983-03-01

Call constants and volume per formula weight are tabulated for RE NiSn (RE = La to Lu, Y) and RE PdSn (RE = Nd to Ho). The unit cell constants are also plotted versus ionic radius of the RE; trends are noted

76 FR 40403 - R.E. Ginna Nuclear Power Plant, LLC, R.E. Ginna Nuclear Power Plant, R.E. Ginna Independent Spent...

Science.gov (United States)

2011-07-08

... NUCLEAR REGULATORY COMMISSION [Docket No. 50-244; Docket No. 72-67] R.E. Ginna Nuclear Power Plant, LLC, R.E. Ginna Nuclear Power Plant, R.E. Ginna Independent Spent Fuel Storage Installation; Notice of... Facility Operating License No. DPR-18, for the R.E. Ginna Nuclear Power Plant (Ginna), currently held by R...

Sculpting carbon bonds for allotropic transformation through solid-state re-engineering of –sp2 carbon

Energy Technology Data Exchange (ETDEWEB)

Jung, Hyun Young; Araujo, Paulo T.; Kim, Young Lae; Jung, Sung Mi; Jia, Xiaoting; Hong, Sanghyun; Ahn, Chi Won; Kong, Jing; Dresselhaus, Mildred S.; Kar, Swastik; Jung, Yung Joon

2014-09-15

Carbon forms one of nature’s strongest chemical bonds; its allotropes having provided some of the most exciting scientific discoveries in recent times. The possibility of inter-allotropic transformations/hybridization of carbon is hence a topic of immense fundamental and technological interest. Such modifications usually require extreme conditions (high temperature, pressure and/or high-energy irradiations), and are usually not well controlled. Here we demonstrate inter-allotropic transformations/hybridizations of specific types that appear uniformly across large-area carbon networks, using moderate alternating voltage pulses. By controlling the pulse magnitude, small-diameter single-walled carbon nanotubes can be transformed predominantly into larger-diameter single-walled carbon nanotubes, multi-walled carbon nanotubes of different morphologies, multi-layered graphene nanoribbons or structures with sp3 bonds. This re-engineering of carbon bonds evolves via a coalescence-induced reconfiguration of sp2 hybridization, terminates with negligible introduction of defects and demonstrates remarkable reproducibility. This reflects a potential step forward for large-scale engineering of nanocarbon allotropes and their junctions.

Electronic structures of ReS sub 2 , ReSe sub 2 and TcS sub 2 in the real and the hypothetical undistorted structures

CERN Document Server

Fang, C M; Haas, C; Groot, R A D

1997-01-01

The transition-metal dichalcogenides ReX sub 2 (X = S or Se) and TcS sub 2 with a d sup 3 electron configuration have distorted CdCl sub 2 and Cd(OH) sub 2 structures, respectively, with the Re(Tc) atoms in each layer forming parallelogram-shaped connected clusters (diamond chain). Ab-initio band-structure calculations were performed for ReX sub 2 and TcS sub 2 , and the hypothetical undistorted 1T-TcS sub 2 and 3R-ReX sub 2 structures. The calculations show that ReS sub 2 , ReSe sub 2 and TcS sub 2 are semiconductors with energy gaps of about 1.0 eV, 0.5 eV and 0.7 eV, respectively, while for the undistorted structures the Fermi level is in the partly filled band of d sub x sub sup 2 sub - sub y sub sup 2 and d sub x sub y orbitals of the t sub 2 sub g manifold. X-ray photoemission spectra for the core levels and valence band of ReSe sub 2 and ReS sub 2 are presented. The valence x-ray photoemission spectra showed that ReS sub 2 is a p-type semiconductor with an energy gap of about 1.5 eV, while ReSe sub 2 i...

(ReTranslating as Re-membering

Directory of Open Access Journals (Sweden)

Julie Tarif

2016-07-01

Full Text Available This paper explores how (retranslation – interlingual and intersemiotic – can be perceived as a way of both remembering the literary legacy of other cultures but also as a way of re-membering/re-generating the body of literature(s of the importing culture. It focuses on what is called “a classic” and anchors its reflexion in polysystem theory and in the metaphorical vision of literary works as an organic living body. To do so, it concentrates on the British literary classic Oliver Twist and its translations and adaptations into French. The article addresses the following questions: What is to be remembered of certain works? Why, how and by whom are those works remembered?

The microstructure and mechanical properties of Mg-3Al-3RE alloys

International Nuclear Information System (INIS)

Tian, X.; Wang, L.M.; Wang, J.L.; Liu, Y.B.; An, J.; Cao, Z.Y.

2008-01-01

The Mg-3Al-3RE alloys (RE, the cerium-rich or the yttrium-rich misch metal) were smelted in a resistance furnace under the protective flux from the Mg-RE master alloys and pure magnesium ingots. The microstructure and mechanical properties of samples prepared by steel mould casting method were investigated. Results show that the main phases of the alloys are α-Mg, Mg 17 Al 12 and Al-RE compounds, and the grain size reduced with the increasing content of the cerium-rich misch metal. Mg-3Al-2Ymm-1Cemm (Ymm, the yttrium-rich misch metal; Cemm, the Cerium-rich misch metal) exhibited the highest mechanical properties, that is UTS = 201 MPa and YS = 75 MPa, and ε = 8.2% at room temperature; UTS = 146 MPa, and YS = 70 MPa, ε = 18.2% at the temperature of 150 deg. C, respectively. Fracture surface analysis revealed that the Mg-3Al-2Ymm-1Cemm alloy has a mixed fracture feature at room temperature but ductile fracture at elevated temperature (150 deg. C)

Extraction of Tc(VII) and Re(VII) on TRU resin

Energy Technology Data Exchange (ETDEWEB)

Guerin, Nicolas; Riopel, Remi; Kramer-Tremblay, Sheila [Canadian Nuclear Laboratories (CNL), Chalk River, ON (Canada). Radiobiology and Health Branch; De Silva, Nimal; Cornett, Jack [Ottawa Univ., ON (Canada). Dept. of Earth and Environmental Sciences; Dai, Xiongxin [China Institute for Radiation Protection, Beijing (China)

2017-06-01

TRU resin can be used to rapidly and selectively extract Tc(VII) and Re(VII). The retention capacity curves of Tc(VII) and Re(VII) for HNO{sub 3}, HCl, H{sub 2}SO{sub 4} and H{sub 3}PO{sub 4} solutions were studied and prepared. Tc(VII) and Re(VII) were simultaneously extracted in 2 M H{sub 2}SO{sub 4} and 1.5 M H{sub 3}PO{sub 4} and were effectively separated from Mo(VI) and Ru(III). Tc(VII) and Re(VII) remained strongly bonded to the resin even after washing using a large volume of 2 M H{sub 2}SO{sub 4} at a relatively high flow rate. Also, they were both completely eluted from the resin using 15 mL of near boiling water, an eluent directly compatible for ICP-MS instrument measurements.

First-principles study of rare-earth (RE) cobaltites (RE=Nd,Sm,Gd,Dy,Er,Lu)

Science.gov (United States)

Topsakal, M.; Wentzcovitch, R. M.

2014-12-01

The lanthanide series of the periodic table comprises 15 members ranging from Lanthanum (La) to Lutetium (Lu). Although they are more abundant than silver, and some of them are more abundant than lead, they are known as rare-earth (RE) elements. The "rare" in their name refers to the difficulty of obtaining the pure elements, not to their abundances in nature. They are never found as free metals in the Earth's crust and do not exist as pure minerals. Using first-principles plane-wave calculations, we investigate the structural and electronic properties of rare-earth cobaltites (RECoO3). Structurally consistent Hubbard U treatment was shown to essential for proper description of strongly correlated cobalt-d electrons. We successfully capture the experimentally observed structural trends and give first-principles insights on interesting phenomena related with the cobalt spin state change. It was demonstrated that increase of crystal-field splitting energy between eg-t2g orbitals and shrinking of unoccupied σ*-bonding eg bands are responsible for the increase of onset spin-state transition temperature along the series.

In vitro structure-activity relationship of Re-cyclized octreotide analogues

Energy Technology Data Exchange (ETDEWEB)

Dannoon, Shorouk F. [Department of Chemistry, University of Missouri, Columbia, MO 65211 (United States); Bigott-Hennkens, Heather M. [Department of Veterinary Medicine and Surgery, University of Missouri, Columbia, MO 65211 (United States); Ma Lixin [Department of Radiology, University of Missouri, Columbia, MO 65211 (United States); International Institute of Nano and Molecular Medicine, University of Missouri, Columbia, MO 65211 (United States); Nuclear Science and Engineering Institute, University of Missouri, Columbia, MO 65211 (United States); Research Service, Harry S. Truman Memorial Veterans' Hospital, Columbia, MO 65201 (United States); Gallazzi, Fabio [Structural Biology Core, University of Missouri, Columbia, MO 65211 (United States); Lewis, Michael R., E-mail: lewismic@missouri.ed [Department of Veterinary Medicine and Surgery, University of Missouri, Columbia, MO 65211 (United States); Department of Radiology, University of Missouri, Columbia, MO 65211 (United States); Nuclear Science and Engineering Institute, University of Missouri, Columbia, MO 65211 (United States); Research Service, Harry S. Truman Memorial Veterans' Hospital, Columbia, MO 65201 (United States); Jurisson, Silvia S., E-mail: jurissons@missouri.ed [Department of Chemistry, University of Missouri, Columbia, MO 65211 (United States); Department of Radiology, University of Missouri, Columbia, MO 65211 (United States); Nuclear Science and Engineering Institute, University of Missouri, Columbia, MO 65211 (United States)

2010-07-15

Introduction: Development of radiolabeled octreotide analogues is of interest for targeting somatostatin receptor (SSTR)-positive tumors for diagnostic and therapeutic purposes. We are investigating a direct labeling approach for incorporation of a Re ion into octreotide analogues, where the peptide sequences are cyclized via coordination to Re rather than through a disulfide bridge. Methods: Various octreotide analogue sequences and coordination systems (e.g., S{sub 2}N{sub 2} and S{sub 3}N) were synthesized and cyclized with nonradioactive Re. In vitro competitive binding assays with {sup 111}In-DOTA-Tyr{sup 3}-octreotide in AR42J rat pancreatic tumor cells yielded IC{sub 50} values as a measure of SSTR affinity of the Re-cyclized analogues. Three-dimensional structures of Re-cyclized Tyr{sup 3}-octreotate and its disulfide-bridged analogue were calculated from two-dimensional NMR experiments to visualize the effect of metal cyclization on the analogue's pharmacophore. Results: Only two of the 11 Re-cyclized analogues investigated showed moderate in vitro binding affinity toward somatostatin subtype 2 receptors. Three-dimensional molecular structures of Re- and disulfide-cyclized Tyr{sup 3}-octreotate were calculated, and both of their pharmacophore turns appear to be very similar with minor differences due to metal coordination to the amide nitrogen of one of the pharmacophore amino acids. Conclusions: Various Re-cyclized analogues were developed and analogue 4 had moderate affinity toward somatostatin subtype 2 receptors. In vitro stable studies that are in progress showed stable radiometal cyclization of octreotide analogues via NS{sub 3} and N{sub 2}S{sub 2} coordination forming five- and six-membered chelate rings. In vivo biodistribution studies are underway of {sup 99m}Tc-cyclized analogue 4.

Re-thinking residential mobility

Science.gov (United States)

van Ham, Maarten; Findlay, Allan M.

2015-01-01

While researchers are increasingly re-conceptualizing international migration, far less attention has been devoted to re-thinking short-distance residential mobility and immobility. In this paper we harness the life course approach to propose a new conceptual framework for residential mobility research. We contend that residential mobility and immobility should be re-conceptualized as relational practices that link lives through time and space while connecting people to structural conditions. Re-thinking and re-assessing residential mobility by exploiting new developments in longitudinal analysis will allow geographers to understand, critique and address pressing societal challenges. PMID:27330243

Synthesis of {sup 188}Re-DMSA complex using carrier-free {sup 188}Re

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, Kazuyuki; Izumo, Mishiroku [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Islam, M S

1997-03-01

The synthesis of rhenium-DMSA labelled compound using carrier-free {sup 188}Re from the {sup 188}W/{sup 188}Re generator has been carried out. Stannous chloride was used as the reducing agent for reduction of rhenium and ascorbic acid was used as an antioxidant in the reaction media. The dependence of the yield of Re-DMSA complex upon the concentration of reducing agent, pH, reaction time, anti-oxidant, carrier and temperature was investigated. Under optimum conditions, the yield of Re-DMSA complexes were more than 98% for the carrier-free as well as carrier-added {sup 188}Re. The stability of the Re-DMSA complexes at different pH and time were also investigated. It was found that the Re-DMSA complex was very stable and did not undergo any changes or decomposition with the changes of pH from its initial values even after 48 hours of pH change for carrier-free as well as carrier-added complexes. (author)

188Re(V) Nitrido Radiopharmaceuticals for Radionuclide Therapy.

Science.gov (United States)

Boschi, Alessandra; Martini, Petra; Uccelli, Licia

2017-01-19

The favorable nuclear properties of rhenium-188 for therapeutic application are described, together with new methods for the preparation of high yield and stable 188 Re radiopharmaceuticals characterized by the presence of the nitride rhenium core in their final chemical structure. 188 Re is readily available from an 188 W/ 188 Re generator system and a parallelism between the general synthetic procedures applied for the preparation of nitride technetium-99m and rhenium-188 theranostics radiopharmaceuticals is reported. Although some differences between the chemical characteristics of the two metallic nitrido fragments are highlighted, it is apparent that the same general procedures developed for the labelling of biologically active molecules with technetium-99m can be applied to rhenium-188 with minor modification. The availability of these chemical strategies, that allow the obtainment, in very high yield and in physiological condition, of 188 Re radiopharmaceuticals, gives a new attractive prospective to employ this radionuclide for therapeutic applications.

188Re(V) Nitrido Radiopharmaceuticals for Radionuclide Therapy

Science.gov (United States)

Boschi, Alessandra; Martini, Petra; Uccelli, Licia

2017-01-01

The favorable nuclear properties of rhenium-188 for therapeutic application are described, together with new methods for the preparation of high yield and stable 188Re radiopharmaceuticals characterized by the presence of the nitride rhenium core in their final chemical structure. 188Re is readily available from an 188W/188Re generator system and a parallelism between the general synthetic procedures applied for the preparation of nitride technetium-99m and rhenium-188 theranostics radiopharmaceuticals is reported. Although some differences between the chemical characteristics of the two metallic nitrido fragments are highlighted, it is apparent that the same general procedures developed for the labelling of biologically active molecules with technetium-99m can be applied to rhenium-188 with minor modification. The availability of these chemical strategies, that allow the obtainment, in very high yield and in physiological condition, of 188Re radiopharmaceuticals, gives a new attractive prospective to employ this radionuclide for therapeutic applications. PMID:28106830

Re-annotation and re-analysis of the Campylobacter jejuni NCTC11168 genome sequence

Directory of Open Access Journals (Sweden)

Dorrell Nick

2007-06-01

Full Text Available Abstract Background Campylobacter jejuni is the leading bacterial cause of human gastroenteritis in the developed world. To improve our understanding of this important human pathogen, the C. jejuni NCTC11168 genome was sequenced and published in 2000. The original annotation was a milestone in Campylobacter research, but is outdated. We now describe the complete re-annotation and re-analysis of the C. jejuni NCTC11168 genome using current database information, novel tools and annotation techniques not used during the original annotation. Results Re-annotation was carried out using sequence database searches such as FASTA, along with programs such as TMHMM for additional support. The re-annotation also utilises sequence data from additional Campylobacter strains and species not available during the original annotation. Re-annotation was accompanied by a full literature search that was incorporated into the updated EMBL file [EMBL: AL111168]. The C. jejuni NCTC11168 re-annotation reduced the total number of coding sequences from 1654 to 1643, of which 90.0% have additional information regarding the identification of new motifs and/or relevant literature. Re-annotation has led to 18.2% of coding sequence product functions being revised. Conclusions Major updates were made to genes involved in the biosynthesis of important surface structures such as lipooligosaccharide, capsule and both O- and N-linked glycosylation. This re-annotation will be a key resource for Campylobacter research and will also provide a prototype for the re-annotation and re-interpretation of other bacterial genomes.

The Chemistry of Re-188 Radiopharmaceuticals: Could Re-188 Play the Same Role in Therapy as Tc-99m in Diagnostics?

International Nuclear Information System (INIS)

Duatti, A.

2009-01-01

Radiopharmaceuticals incorporating the β-emitting radionuclide Re-188 are still attracting much interest for their potential application in nuclear medicine as therapeutic agents. There are many advantages of employing this class of radioactive compounds as briefly summarized in the following. (1) Re-188 emits a high-energy β- particle (2.1 MeV) that can be efficiently used to deliver high-dose radiation to the target. (2) Re-188 concomitantly emits a 155-keV γ photon that can be conveniently employed to obtain good-quality SPECT images of the biodistribution of Re-188 radiopharmaceuticals and, ultimately, following in vivo the course of the therapy. (3) Re-188 has a relatively short half-life (17 hours) that may allow multiple treatments of the same patient's disease. (4) Re-188 is a radiometal belonging to the same group of Tc-99m in the transition metal series of the Periodic Table, and shares with its cogener similar (though not identical) chemical properties that could be useful for designing a broad class of Re-188 radiopharmaceuticals having the same biodistribution properties of the corresponding Tc-99m analogues. (5) Similarly to Tc-99m, the radionuclide Re-188 is produced in high-specific activity through the 188 W/ 188 Re transportable generator system. A first challenge encountered in the attempt to develop efficient labeling procedures for Re-188 was related to the low radiochemical yield usually observed in tracer-level preparations of Re-188 radiopharmaceuticals starting from generator-produced [ 188 ReO 4 ]-. This drawback is commonly associated with the low value of the standard reduction potential of the tetraoxo anion as compared to the corresponding Tc-99m pertechnetate anion. In recent years, we reported a simple and efficient procedure for overcoming this problem based on a general chemical principle called 'expansion of the coordination sphere' and involving the addition to the reaction vial of an ancillary ligand (usually, chelating hard

Quaternary rare-earth sulfides RE{sub 3}M{sub 0.5}GeS{sub 7} (RE=La–Nd, Sm; M=Co, Ni) and Y{sub 3}Pd{sub 0.5}SiS{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Iyer, Abishek K. [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Yin, Wenlong [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Institute of Chemical Materials, China Academy of Engineering Physics, Mianyang 621900 (China); Lee, Emma J. [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Lin, Xinsong [Centre for Oil Sands Sustainability, Northern Alberta Institute of Technology, Edmonton, Alberta, Canada T6N 1E5 (Canada); Mar, Arthur, E-mail: arthur.mar@ualberta.ca [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada)

2017-06-15

The two metal-deficient series of quaternary Ge-containing sulfides RE{sub 3}M{sub 0.5}GeS{sub 7} (RE = La–Nd, Sm; M = Co, Ni), as well as the related Si-containing sulfide Y{sub 3}Pd{sub 0.5}SiS{sub 7}, were prepared by reactions of the elements at 1050 °C. Single-crystal X-ray diffraction analysis performed on all compounds confirmed noncentrosymmetric hexagonal structures (space group P6{sub 3}, Z =2) with cell parameters in the ranges of a =10.0–10.3 Å and c =5.7–5.8 Å for RE{sub 3}Co{sub 0.5}GeS{sub 7} and RE{sub 3}Ni{sub 0.5}GeS{sub 7}, or a =9.7891(3) Å and c =5.6840(4) Å for Y{sub 3}Pd{sub 0.5}SiS{sub 7}. They are classified as La{sub 3}Mn{sub 0.5}SiS{sub 7}-type structures, with M atoms centred within octahedra (in contrast to La{sub 3}CuSiS{sub 7}-type structures in which M atoms occupy trigonal planar sites) and Ge atoms centred within tetrahedra, both types of polyhedra being arranged in one-dimensional stacks aligned along the c-direction. Charge balance requirements dictate half-occupancy of the M sites. However, bond valence sum arguments indicated that the M atoms are somewhat underbonded within these octahedral sites, so that there is evidence that in some compounds, they can also enter the trigonal planar site at low occupancy (~5%). Magnetic measurements on RE{sub 3}Co{sub 0.5}GeS{sub 7} (RE = Ce, Pr, Sm) revealed paramagnetic behaviour for the Ce and Pr members and apparent antiferromagnetic ordering (T{sub N} =14 K) for the Sm member; fitting to the Curie-Weiss law gave effective magnetic moments consistent with the presence of RE{sup 3+} and Co{sup 2+} species. Band structure calculations on ordered models of La{sub 3}M{sub 0.5}GeS{sub 7} (M = Co, Ni) showed that the Fermi level cuts through M 3d states in the DOS curve and supported the presence of strong M–S and Ge–S bonding interactions. - Graphical abstract: RE{sub 3}M{sub 0.5}GeS{sub 7} (M = Co, Ni) and Y{sub 3}Pd{sub 0.5}SiS{sub 7} contain M atoms partially occupying

Labelling of Re-ABP with 188Re for bone pain palliation

International Nuclear Information System (INIS)

Arteaga de Murphy, Consuelo; Ferro-Flores, Guillermina; Pedraza-Lopez, Martha; Melendez-Alafort, Laura; Croft, B.Y.Barbara Y.; Ramirez, Flor de Maria; Padilla, Juan

2001-01-01

Etidronate and medronate have been labelled with technetium-99m ( 99m Tc-HEDP, 99m Tc-MDP) for bone scanning and, with rhenium-188 ( 188 Re-HEDP) to palliate the pain resulting from bone metastases. The objective of this study was to label alendronate, ABP, a new bisphosphonate, with SnF 2 -reduced- 188 Re. The reagents for the 5 mg ABP kit were SnF 2 , KReO 4 and gentisic acid at acid pH. The chemical, spectroscopic and microscopic characteristics, quality control, rat bone uptake of [ 188 Re]Re-ABP and similarities with 99m Tc-ABP are presented. We conclude that this is a promising new radiopharmaceutical for bone metastases pain palliation

Dynamic re-weighted total variation technique and statistic Iterative reconstruction method for x-ray CT metal artifact reduction

Science.gov (United States)

Peng, Chengtao; Qiu, Bensheng; Zhang, Cheng; Ma, Changyu; Yuan, Gang; Li, Ming

2017-07-01

Over the years, the X-ray computed tomography (CT) has been successfully used in clinical diagnosis. However, when the body of the patient to be examined contains metal objects, the image reconstructed would be polluted by severe metal artifacts, which affect the doctor's diagnosis of disease. In this work, we proposed a dynamic re-weighted total variation (DRWTV) technique combined with the statistic iterative reconstruction (SIR) method to reduce the artifacts. The DRWTV method is based on the total variation (TV) and re-weighted total variation (RWTV) techniques, but it provides a sparser representation than TV and protects the tissue details better than RWTV. Besides, the DRWTV can suppress the artifacts and noise, and the SIR convergence speed is also accelerated. The performance of the algorithm is tested on both simulated phantom dataset and clinical dataset, which are the teeth phantom with two metal implants and the skull with three metal implants, respectively. The proposed algorithm (SIR-DRWTV) is compared with two traditional iterative algorithms, which are SIR and SIR constrained by RWTV regulation (SIR-RWTV). The results show that the proposed algorithm has the best performance in reducing metal artifacts and protecting tissue details.

Preparation of 186Re complexes of dimercaptosuccinic acid hydroxy ethylidine diphosphonate

International Nuclear Information System (INIS)

Kothari, K.; Pillai, M.R.A.; Unni, P.R.; Mathakar, A.R.; Shimpi, H.H.; Noronha, O.P.D.; Samuel, A.M.

1998-01-01

99m Tc(V)-DMSA and 99m Tc-HEDP are widely used for imaging medullary carcinoma and bone, respectively. 186 Re-HEDP is now well established as a therapeutic radiopharmaceutical for palliation of pain due to bone metastases. It is expected that 186/188 Re(V)-DMSA could find application for treating medullary carcinoma. In the present paper we report the work carried out for the preparation of 186 Re complexes of DMSA and HEDP and their bio-distribution studies in Wistar rats. 186 Re was prepared by irradiation of natural Re metal at a flux of 3x10 13 neutrons/cm 2 /s for seven days and processed after a cooling period of four days. The specific activity of 186 Re formed was ∼35 mCi/mg. Complexes with RC purity >98% could be prepared in both the cases by carefully optimizing the reaction conditions. Bio-distribution studies carried out in rats revealed that pharmacological behaviour of 186 Re(V)-DMSA was similar to that of 99m Tc(V)-DMSA. 186 Re-HEDP showed a bone uptake of ∼ 30% at 3 h post injection which remained almost constant for 48 h. (author)

Revision total hip arthoplasty: factors associated with re-revision surgery.

Science.gov (United States)

Khatod, Monti; Cafri, Guy; Inacio, Maria C S; Schepps, Alan L; Paxton, Elizabeth W; Bini, Stefano A

2015-03-04

highly cross-linked polyethylene bearing articulation decreases the hazard relative to metal on highly cross-linked polyethylene by a factor of 0.32 (95% confidence interval, 0.11 to 0.95). Metal on constrained bearing increases the hazard relative to metal on highly cross-linked polyethylene by a factor of 3.32 (95% confidence interval, 1.16 to 9.48). When evaluating patient, implant, and surgical factors at the time of revision total hip arthroplasty, age, surgeon experience, implant fixation, and bearing surfaces had significant impacts on the risk of re-revision. Copyright © 2015 by The Journal of Bone and Joint Surgery, Incorporated.

Improved Mo-Re VPS Alloys for High-Temperature Uses

Science.gov (United States)

Hickman, Robert; Martin, James; McKechnie, Timothy; O'Dell, John Scott

2011-01-01

Dispersion-strengthened molybdenum- rhenium alloys for vacuum plasma spraying (VPS) fabrication of high-temperature-resistant components are undergoing development. In comparison with otherwise equivalent non-dispersion-strengthened Mo-Re alloys, these alloys have improved high-temperature properties. Examples of VPS-fabricated high-temperature-resistant components for which these alloys are expected to be suitable include parts of aircraft and spacecraft engines, furnaces, and nuclear power plants; wear coatings; sputtering targets; x-ray targets; heat pipes in which liquid metals are used as working fluids; and heat exchangers in general. These alloys could also be useful as coating materials in some biomedical applications. The alloys consist of 60 weight percent Mo with 40 weight percent Re made from (1) blends of elemental Mo and Re powders or (2) Re-coated Mo particles that have been subjected to a proprietary powder-alloying-and-spheroidization process. For most of the dispersion- strengthening experiments performed thus far in this development effort, 0.4 volume percent of transition-metal ceramic dispersoids were mixed into the feedstock powders. For one experiment, the proportion of dispersoid was 1 volume percent. In each case, the dispersoid consisted of either ZrN particles having sizes <45 m, ZrO2 particles having sizes of about 1 m, HfO2 particles having sizes <45 m, or HfN particles having sizes <1 m. These materials were chosen for evaluation on the basis of previously published thermodynamic stability data. For comparison, Mo-Re feedstock powders without dispersoids were also prepared.

Re-qualification of MTR-type fuel plates fabrication process

International Nuclear Information System (INIS)

Elseaidy, I.M.; Ghoneim, M.M.

2010-01-01

The fabricability issues with increased uranium loading due to use low enrichment of uranium (LEU), i.e. less than 20 % of U 235 , increase the problems which occur during compact manufacturing, roll bonding of the fuel plates, potential difficulty in forming during rolling process, mechanical integrity of the core during fabrication, potential difficulty in meat homogeneity, and the ability to fabricate plates with thicker core as a means of increasing total uranium loading. To produce MTR- type fuel plates with high uranium loading (HUL) and keep the required quality of these plates, many of qualification process must be done in the commissioning step of fuel fabrication plant. After that any changing of the fabrication parameters, for example changing of any of the raw materials, devises, operators, and etc., a re- qualification process should be done in order to keep the quality of produced plates. Objective of the present work is the general description of the activities to be accomplished for re-qualification of manufacturing MTR- type nuclear fuel plates. For each process to be re-qualified, a detailed of re-qualification process were established. (author)

Chemical activation of molecules by metals: Experimental studies of electron distributions and bonding

International Nuclear Information System (INIS)

Lichienberger, D.L.

1990-10-01

This quarter has witnessed further progress both in our experimental methods of photoelectron spectroscopy and in our understanding the fundamental relationships between ionization energies and the chemistry of transition metal species. Progress continues on the new gas phase photoelectron spectrometer that combine improved capabilities for HeI/HeII UPS, XPS, and Auger investigations of organometallic molecules. Several measurements have been accomplished this year that were not possible previously. We have published the formal relationship between measured molecular ionization energies and thermodynamic bond dissociation energies, and applied the relationships to homonuclear and heteronuclear diatomic molecules, multiple bonds, and metal-ligand bonds. Studies of C-H bond activation have continued with examination of different degrees of Si-H bond addition to metals. the electronic effects of intermolecular interactions have been observed by comparing the ionizations of metal complexes in the gas phase with the ionizations of monolayer solid organometallic films prepared in ultra-high vacuum. The orientations of the molecules have been determined by scanning tunneling microscopy. Especially interesting has been the recent application of these techniques to the characterization of the soccer-ball shaped C 60 molecule, buckminsterfullerene. Studies of the following complexes are described : Fe, Os, Nb, Mo, Rh, Re, Al, and Mn. 19 refs

Preparation of cyclotron-produced {sup 186}Re and comparison with reactor-produced {sup 186}Re and generator-produced {sup 188}Re for the labeling of bombesin

Energy Technology Data Exchange (ETDEWEB)

Moustapha, Moustapha E. [Department of Chemistry, University of Missouri-Columbia, Columbia, MO 65211 (United States); University of Missouri Research Reactor (MURR), University of Missouri-Columbia, Columbia, MO 65211 (United States); Ehrhardt, Gary J. [Department of Chemistry, University of Missouri-Columbia, Columbia, MO 65211 (United States); University of Missouri Research Reactor (MURR), University of Missouri-Columbia, Columbia, MO 65211 (United States); Smith, Charles J. [Department of Radiology, University of Missouri-Columbia, Columbia, MO 65211 (United States); University of Missouri Research Reactor (MURR), University of Missouri-Columbia, Columbia, MO 65211 (United States); Research Services, Harry S. Truman Memorial Veterans' Hospital, Columbia, MO 65201 (United States); Szajek, Lawrence P. [Positron Emission Tomography Department, National Institutes of Health, Bethesda, MD 20892-1180 (United States); Eckelman, William C. [Positron Emission Tomography Department, National Institutes of Health, Bethesda, MD 20892-1180 (United States); Jurisson, Silvia S. [Department of Chemistry, University of Missouri-Columbia, Columbia, MO 65211 (United States)]. E-mail: jurissons@missouri.edu

2006-01-15

The radioisotopes {sup 186}Re and {sup 188}Re have been extensively investigated for various forms of radiotherapy due to their useful and high-abundance {beta} particle emissions, low-abundance and imageable {gamma}-rays, and chemical resemblance to technetium. In addition, {sup 188}Re is available in no-carrier-added (NCA) form from long lived W-188 generators, whereas {sup 186}Re can be produced in large quantities from reactors, although not in NCA form. However, NCA {sup 186}Re can be produced on a cyclotron by a (p,n) reaction on {sup 186}W. The purpose of this study was to compare labeling of the peptide bombesin with these three forms of rhenium radioisotopes. Cyclotron-produced NCA {sup 186}Re was separated radiochemically from enriched {sup 186}W (96.9%) targets using high-purity methyl ethyl ketone (MEK). The resulting {sup 186}Re-MEK was then loaded onto a small alumina column to separate the resulting NCA {sup 186}Re from any remaining {sup 186}W. The experimental levels of impurities associated with {sup 186}Re at the end of the separation process were found to be 5.7x10{sup -6} Ci of {sup 182}Re (0.57%, t {sub 1/2}=12.7 h) and 1.283x10{sup -5} Ci of {sup 182m}Re (1.28%, t {sub 1/2}=2.67 days). The radionuclidic purity of the separated {sup 186}Re was found to be 99.6%, whereas the chemical identity was determined by reversed phase high-performance liquid chromatography (RP-HPLC) to be perrhenate ({sup 186}ReO{sub 4} {sup -}). Generator-produced {sup 188}ReO{sub 4} {sup -} from a {sup 188}W/{sup 188}Re generator (Oak Ridge National Laboratory) and CA {sup 186}ReO{sub 4} {sup -} produced from a {sup 185}Re(n,{gamma}){sup 186}Re reaction at the University of Missouri Research Reactor (MURR) were used for comparison with the NCA {sup 186}Re in subsequent studies. N{sub 3}S-5-Ava-BBN(7-14)NH{sub 2} conjugates provide flexibility for designing {sup 186,188}Re-labeled conjugates that retain high in vitro and in vivo specificity targeting of GRP receptor

Rare earth-rich cadmium compounds RE{sub 10}TCd{sub 3} (RE = Y, Tb, Dy, Ho, Er, Tm, Lu; T = Rh, Pd, Ir, Pt) with an ordered Co{sub 2}Al{sub 5}-type structure

Energy Technology Data Exchange (ETDEWEB)

Block, Theresa; Klenner, Steffen; Heletta, Lukas; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie

2018-04-01

Eighteen new rare earth-rich intermetallic phases RE{sub 10}TCd{sub 3} (RE = Y, Tb, Dy, Ho, Er, Tm, Lu; T = Rh, Pd, Ir, Pt) were obtained by induction melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. All samples were characterized by X-ray powder diffraction. The structures of four representatives were refined from single-crystal X-ray diffractometer data: ordered Co{sub 2}Al{sub 5} type, P6{sub 3}/mmc, a = 951.2(1), c = 962.9(2) pm, wR = 0.0460, 595 F{sup 2} values, 20 parameters for Er{sub 10}RhCd{sub 3}; a = 945.17(4), c = 943.33(4), wR = 0.0395, 582 F{sup 2} values, 21 parameters for Lu{sub 9.89}PdCd{sub 3.11}; a = 964.16(6), c = 974.93(6) pm, wR = 0.0463, 614 F{sup 2} values, 21 parameters for Y{sub 10}Ir{sub 1.09}Cd{sub 2.91}; a = 955.33(3), c = 974.56(3) pm, wR = 0.0508, 607 F{sup 2} values, 22 refined parameters for Dy{sub 9.92}IrCd{sub 3.08}. Refinements of the occupancy parameters revealed small homogeneity ranges resulting from RE/Cd, respectively T/Cd mixing. The basic building units of the RE{sub 10}TCd{sub 3} phases are transition metal-centered RE{sub 6} trigonal prisms (TP) that are condensed with double-pairs of empty RE{sub 6} octahedra via common triangular faces. A second type of rods is formed by slightly distorted RE3 rate at Cd{sub 6}RE{sub 6} icosahedra which are condensed via Cd{sub 3} triangular faces. The shortest interatomic distances occur for RE-T, compatible with strong covalent bonding interactions. Temperature dependent magnetic susceptibility measurements were performed for RE{sub 10}RhCd{sub 3} (RE = Dy-Tm, Lu), RE{sub 10}IrCd{sub 3} (RE = Er, Tm, Lu) and RE{sub 10}PtCd{sub 3} (RE = Y, Lu). While Y{sub 10}PtCd{sub 3} and Lu{sub 10}TCd{sub 3} (T = Rh, Ir, Pt) show Pauli paramagnetic behavior, the compounds containing paramagnetic rare earth elements show Curie-Weiss behavior (the experimental magnetic moments indicate stable trivalent RE{sup 3+}) and magnetic ordering at low temperatures

Re-irradiation tests of spent fuel at JMTR by means of re-instrumentation technique

International Nuclear Information System (INIS)

Nakamura, Jinichi; Shimizu, Michio; Endo, Yasuichi; Nabeya, Hideaki; Ichise, Kenichi; Saito, Junichi; Oshima, Kunio; Uetsuka, Hiroshi

1999-01-01

JAERI has developed re-irradiation test procedures of spent fuel irradiated at commercial reactor by means of re-instrumentation technique. Full length rods irradiated at commercial LWRs were re-fabricated to short length rods, and rod inner pressure gauges and fuel center thermocouples were re-instrumented to the rods. Re-irradiation tests to study the fuel behavior during power change were carried out by means of BOCA/OSF-1 facility at the JMTR. In the tests to study the fission gas release during power change, the rod inner pressure increase was observed during power change, especially during power reduction. The fission gas release during power reduction is estimated to be the release from fission gas bubbles on the grain boundary caused by the thermal stress in the pellet during power reduction. Re-irradiation test of gadolinia added fuel was performed by means of dual re-instrumentation technique (fuel center thermocouples and rod inner pressure gauge). A stepwise fission gas release during power change, and the following fuel center temperature change due to gap conductance change were observed. (author)

Veritex(TM) Patches for Structural Repair and Re-Use, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Cornerstone Research Group, Inc. (CRG) proposes to develop a bonded composite patch repair and re-use system based on CRG's VeritexTM materials. VeritexTM is a...

Studies of HEDP labelled with 188Re from different generators of 188W /188Re

International Nuclear Information System (INIS)

Marczewski, Barbara Szot

2006-01-01

The widespread interest in 188 Re for therapeutic applications, is due to its attractive 16,9 hours half-life, emission of a β - particle with maximum energy of 2.12 MeV and gamma-ray of 155 keV suitable for imaging. This work presents the radiolabelling of HEDP (etidronate) with 188 Re eluted from alumina-based 188 W/ 188 Re generators and tungstate-based 188 W/ 188 Re gel generators. Dependence of the yield of the 18 '8Re-HEDP on the concentration of the reduction agent, p H, reaction time, temperature and addition of carrier Re 2 O 7 were evaluated. The radiolabelling of 188 Re-HEDP procedure using the optimum conditions resulted a yield >= 98% for liquid and lyophilized kits. This basic formulation contains: 30 mg de HEDP, 7 mg de SnCl 2 , 3 mg de ascorbic acid and addition of 20 mug of Re 2 O 7 . The reactions were carried out with heating in boiling water for 30 minutes followed by 60 minutes of incubation. Another important aspect of this work was the radiochemical quality control comparing the results of PC, TLC and ion chromatography, along with the experiments with HPLC. The biological distribution proved the adequate bone uptake and in vivo stability of 188 Re-HEDP complexes. (author)

Investigation on thermophysical properties of RE{sub 6}UO{sub 12}(s) (RE = La, Pr, Nd, Sm)

Energy Technology Data Exchange (ETDEWEB)

Sahu, Manjulata, E-mail: manju@barc.gov.in [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Krishnan, K. [Fuel Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Jain, Dheeraj [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Saxena, M.K. [Radioanalytical Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Dash, Smruti [Product development Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2016-08-10

Highlights: • Synthesis of RE{sub 6}UO{sub 12}(s)(RE = La, Pr, Nd, Sm) was performed by combustion method and characterization by XRD. • Thermal expansion measurements were carried out on RE{sub 6}UO{sub 12}(s)(RE = Pr, and Sm) using HT-XRD. • Heat capacity of RE{sub 6}UO{sub 12}(s)(RE = La, Pr, Nd, Sm) was measured in the temperature range 300–870 K. • The nonstoichiometry in RE{sub 6}UO{sub 12}(s) was checked using TG, XPS, chemical analysis and electrical conductivity measurement. - Abstract: RE{sub 6}UO{sub 12}(s) (RE = La, Pr, Nd, Sm) was synthesized by citrate-nitrate combustion method. The synthesis condition for Pr{sub 6}UO{sub 12}(s) was optimized. Nonstoichiometry in these rare earth uranates in argon atmosphere was analysed using various techniques like thermogravimetry (TG), X-ray photo electron spectroscopy (XPS), chemical analysis and electrical conductivity measurements. Thermal expansions of RE{sub 6}UO{sub 12}(s) (RE = Pr and Sm) was studied in the temperature range 298–1273 K by high temperature X-ray powder diffractometry and compared with that of similar rare earth compounds reported in the literature. Heat capacity of RE{sub 6}UO{sub 12}(s) (RE = La, Pr, Nd, Sm) was measured by differential scanning calorimetry in the temperature range 300–870 K. Enthalpy, entropy and Gibbs energy functions of these compounds were computed from the measured heat capacity data.

Influence of annealing temperature on structural and optical properties of SiO{sub 2}:RE{sub 2}O{sub 3} [RE = Y, Gd] powder

Energy Technology Data Exchange (ETDEWEB)

Ahlawat, Rachna, E-mail: rachnaahlawat2003@yahoo.com

2015-07-25

Highlights: • Sol–gel process is used to obtain spherical nanocrystallites of SiO{sub 2}:RE{sub 2}O{sub 3} [RE = Y, Gd] powder. • Effect of four steps annealing is studied on micro strain, nanocrystallite size and dislocation density. • Optical properties are examined by absorption spectra and PL. • SiO{sub 2}:RE{sub 2}O{sub 3} [RE = Y, Gd] binary oxides are promising materials for high temperature structural applications. - Abstract: SiO{sub 2}:RE{sub 2}O{sub 3} [RE = Y, Gd] powder were prepared by wet chemical technique and the prepared binary oxides annealed at 500 °C and 900 °C. The crystalline structure, phase transformation, and surface morphologies of as-prepared and annealed samples were investigated by XRD and TEM. The normal transmission was measured using FTIR spectroscopy. Optical properties have been studied with UV–Vis spectroscopy and PL study. XRD results shows that the as prepared samples of SiO{sub 2}:RE{sub 2}O{sub 3} [RE = Y, Gd] powder has mixed phases of RE(NO{sub 3}){sub 3} and Si(OH){sub 3}. However, cubic rare earth oxide phase alone is found for annealed samples. The strain values are calculated from W–H plot for annealed samples. TEM micrograph shows that the samples are composed of individual spherical nanocrystallites at 500 °C and aggregated nanocrystallites at 900 °C. From the UV–Vis spectra, it is found that the position of the absorption peak is shifted toward the higher wavelength side when annealing temperature is increased. In the PL spectra, the broad emission bands are observed between 570–600 nm and the presence of O–Si–O (silica) and metal oxide is confirmed by FTIR spectra.

Atomistic mechanisms of ReRAM cell operation and reliability

Science.gov (United States)

Pandey, Sumeet C.

2018-01-01

We present results from first-principles-based modeling that captures functionally important physical phenomena critical to cell materials selection, operation, and reliability for resistance-switching memory technologies. An atomic-scale description of retention, the low- and high-resistance states (RS), and the sources of intrinsic cell-level variability in ReRAM is discussed. Through the results obtained from density functional theory, non-equilibrium Green’s function, molecular dynamics, and kinetic Monte Carlo simulations; the role of variable-charge vacancy defects and metal impurities in determining the RS, the LRS-stability, and electron-conduction in such RS is reported. Although, the statistical electrical characteristics of the oxygen-vacancy (Ox-ReRAM) and conductive-bridging RAM (M-ReRAM) are notably different, the underlying similar electrochemical phenomena describing retention and formation/dissolution of RS are being discussed.

Adsorption and dissociation of dinitrogen on transition metal (Ta, W and Re) doped MgO surface

KAUST Repository

Yadav, Manoj Kumar

2016-06-16

The adsorption and dissociation of dinitrogen on transition metal (Ta, W and Re) doped MgO(100) surface has been studied employing density functional theory. It is found that all these transition metals (TM) on MgO(100) surface are capable of adsorbing dinitrogen (N2), however there is no dissociative adsorption of N2 on single transition metal dopant. When two TM atoms are doped on MgO(100) surface, dissociative adsorption of dinitrogen occurs in all the three cases. Whether the dissociation is spontaneous or is it associated with activation barrier depends on the orientation of N2 molecule approaching the dopant site.

Trapping and re-emission of energetic hydrogen and helium ions in materials

International Nuclear Information System (INIS)

Yamaguchi, Sadae

1981-01-01

The experimental results on the trapping and re-emission of energetic hydrogen and helium ions in materials are explained. The trapping of deuterium and helium in graphite saturates at the concentration of 10 18 ions/cm 2 . The trapping rate of hydrogen depends on the kinds of target materials. In the case of the implantation in Mo over 3 x 10 16 H/cm 2 , hydrogen is hardly trapped. On the other hand, the trapping of hydrogen in Ti, Zr and Ta which form solid solution is easily made. The hydrogen in these metals can diffuse toward the inside of metals. The deuterium retained in 316 SS decreased with time. The trapping rate reached saturation more rapidly at higher implantation temperature. The effective diffusion constant for the explanation of the re-emission process is 1/100 as small as the ordinary value. The radiation damage due to helium irradiation affects on the trapping of deuterium in Mo. The temperature dependence of the trapping rate can be explained by the diffusion model based on the Sievert's law. The re-emission of helium was measured at various temperature. At low temperature, the re-emission was low at first, then the rate increased. At high temperature, the re-emission rate was high from the beginning. (Kato, T.)

A parity-breaking electronic nematic phase transition in the spin-orbit coupled correlated metal Cd2Re2O7

Science.gov (United States)

Harter, J. W.; Zhao, Z. Y.; Yan, J.-Q.; Mandrus, D. G.; Hsieh, D.

Strong interactions between electrons are known to drive metallic systems toward a variety of well-known symmetry-broken phases, including superconducting, electronic liquid crystalline, and charge- and spin-density wave ordered states. In contrast, the electronic instabilities of correlated metals with strong spin-orbit coupling have only recently begun to be explored. We uncover a novel multipolar nematic phase of matter in the metallic pyrochlore Cd2Re2O7 using spatially-resolved second-harmonic optical anisotropy measurements. Like previously discovered electronic liquid crystalline phases, this multipolar nematic phase spontaneously breaks rotational symmetry while preserving translational invariance. However, it has the distinguishing property of being odd under spatial inversion, which is allowed only in the presence of spin-orbit coupling. By examining the critical behavior of the multipolar nematic order parameter, we show that it drives the thermal phase transition near 200 K in Cd2Re2O7 and induces a parity-breaking lattice distortion as a secondary order parameter.

checkCIF/PLATON report Datablock: monika-bd1re3

Indian Academy of Sciences (India)

IF USED AS PART OF A REVIEW PROCEDURE. FOR PUBLICATION, IT SHOULD NOT REPLACE THE EXPERTISE OF AN EXPERIENCED. CRYSTALLOGRAPHIC REFEREE. No syntax errors found. CIF dictionary Interpreting this report. Datablock: monika-bd1re3. Bond precision: C-C = 0.0046 A. Wavelength=0.71073.

Analysis of heavy metals in the re-suspended road dusts from different functional areas in Xi'an, China.

Science.gov (United States)

Wang, Qian; Lu, Xinwei; Pan, Huiyun

2016-10-01

A study on heavy metal pollution was undertaken in the re-suspended road dusts from different functional areas in Xi'an City of China to investigate the impacts of human activities and land uses on urban environment. The concentrations of Co, Cr, Cu, Mn, Ni, Pb, V, and Zn were determined using X-ray fluorescence spectrometry, and their accumulations were analyzed using enrichment factor. Correlation analysis, principal component analysis, and cluster analysis, combined with the concentration property and enrichment factor, were used to identify the possible sources of heavy metals investigated. The investigated re-suspended road dusts had Co, Cr, Cu, Pb, and Zn concentrations higher than background levels. Samples from different functional areas had diverse heavy metal concentration levels. Co, Cr, Cu, Pb, and Zn presented moderate/significant enrichment in the samples. The source analyses indicated that Mn, Ni, V, Pb, and Zn had the mixed sources of nature and traffic, Cr and Cu mainly originated from traffic source, while Co was primarily derived from construction source. Traffic and construction activities had a significant impact on urban environment. This preliminary research provides a valuable basis for urban environment protection and management.

Crystal Structure, Spectroscopic Investigations, and Physical Properties of the Ternary Intermetallic REPt2Al3 (RE = Y, Dy–Tm and RE2Pt3Al4 Representatives (RE = Tm, Lu

Directory of Open Access Journals (Sweden)

Fabian Eustermann

2018-04-01

Full Text Available The REPt2Al3 compounds of the late rare-earth metals (RE = Y, Dy–Tm were found to crystallize isostructural. Single-crystal X-ray investigations of YPt2Al3 revealed an orthorhombic unit cell (a = 1080.73(6, b = 1871.96(9, c = 413.04(2 pm, wR2 = 0.0780, 942 F2 values, 46 variables with space group Cmmm (oC48; q2pji2hedb. A comparison with the Pearson database indicated that YPt2Al3 forms a new structure type, in which the Pt and Al atoms form a [Pt2Al3]δ− polyanion and the Y atoms reside in the cavities within the framework. Via a group-subgroup scheme, the relationship between the PrNi2Al3-type structure and the new YPt2Al3-type structure was illustrated. The compounds with RE = Dy–Tm were characterized by powder X-ray diffraction experiments. While YPt2Al3 is a Pauli-paramagnet, the other REPt2Al3 (RE = Dy–Tm compounds exhibit paramagnetic behavior, which is in line with the rare-earth atoms being in the trivalent oxidation state. DyPt2Al3 and TmPt2Al3 exhibit ferromagnetic ordering at TC = 10.8(1 and 4.7(1 K and HoPt2Al3 antiferromagnetic ordering at TN = 5.5(1 K, respectively. Attempts to synthesize the isostructural lutetium compound resulted in the formation of Lu2Pt3Al4 (Ce2Ir3Sb4-type, Pnma, a = 1343.4(2, b = 416.41(8, c = 1141.1(2 pm, which could also be realized with thulium. The structure was refined from single-crystal data (wR2 = 0.0940, 1605 F2 values, 56 variables. Again, a polyanion with bonding Pt–Al interactions was found, and the two distinct Lu atoms were residing in the cavities of the [Pt3Al4]δ– framework. X-ray photoelectron spectroscopy (XPS measurements were conducted to examine the electron transfer from the rare-earth atoms onto the polyanionic framework.

Re-torsion of the ovaries

DEFF Research Database (Denmark)

Hyttel, Trine E W; Bak, Geske S; Larsen, Solveig B

2015-01-01

The increasing use of de-torsion of the ovaries may result in re-torsion. This review addresses risk of re-torsion and describes preventive strategies to avoid re-torsion in pre-menarcheal girls, and fertile and pregnant women. We clinically reviewed PubMed, Embase, Trip and Cochrane databases. T...

Re-Entry Trauma: Asian Re-Integration after Study in the West

Science.gov (United States)

Pritchard, Rosalind

2011-01-01

Many students who re-locate from host to home country are said to undergo a process of reverse culture shock akin to bereavement, involving stages of a grieving process. This has been likened to a "W-curve" in which feelings fluctuate before reaching a more balanced state. The present study examined the re-acculturation of Taiwanese and…

Critical evaluation and thermodynamic optimisation of the Si-RE systems: Part II. Si-RE system (RE = Gd, Tb, Dy, Ho, Er, Tm, Lu and Y)

International Nuclear Information System (INIS)

Kim, Junghwan; Jung, In-Ho

2015-01-01

Highlights: • The (Si-RE) (RE = Gd, Tb, Dy, Ho, Er, Tm, Lu and Y) systems have been reviewed. • The thermodynamic optimization of the (Si-RE) systems have been performed. • Systematic changes and similarities in the (Si-RE) systems were found. • The systematic approach resolved inconsistencies in the experimental data. • The systematic approach was used to assess the unexplored phase diagrams. - Abstract: A critical evaluation and optimisation of all available phase diagrams and thermodynamic data of the (Si-RE) (RE = Gd, Tb, Dy, Ho, Er, Tm, Lu and Y) systems was conducted to obtain reliable thermodynamic functions of all the phases in the system. In the thermodynamic modelling, a systematic analysis involving the similarity and periodicity observed in the lanthanide series was applied to resolve inconsistencies in the experimental data and to estimate the unknown thermodynamic properties and phase equilibria data. In particular, the phase diagrams and thermodynamic properties of (Si-Tm) and (Si-Lu) systems which are rarely investigated can be predicted from this approach. Systematic trends in thermodynamic properties of solid and liquid phases and phase diagram of the entire (Si-RE) systems were summarized

Entrepreneurship as re-sourcing

DEFF Research Database (Denmark)

Korsgaard, Steffen; Anderson, Alistair; Gaddefors, Johan

Objectives The purpose of this paper is to re-examine the concept of entrepreneurship in light of the current financial and environmental crisis and its socio-spatial impact. Building on Hudson’s analysis of production in late-capitalist societies, we identify problems inherent in the dominant...... of grounding in material reality, lacking emphasis on environmental externalities and an impoverished conceptualization of spatial relations. Comparing this analysis with the dominant opportunistic image of the entrepreneur, leads us to formulate a critique of this image. In formulating an alternative we build...... The paper presents a “new image” of entrepreneurship as re-sourcing. The concept of re-sourcing emphasizes the dual meaning of the word resource as both a stock of supply and strategy or action adopted in adverse circumstances. Re-sourcing thus signifies a shift in focus from opportunities to resources...

Electronic Switch in the Carbon-Centered [Re12CS17(CN6] n−Nanocluster

Directory of Open Access Journals (Sweden)

Gabuda SP

2009-01-01

Full Text Available Abstract An abrupt change in internuclear Re–Re distances between {Re6} subunits in the carbon-centered [Re12μ6-CS17(CN6] n−complexes caused by the change of the oxidation state (n = 6, 8 is first theoretically shown to be possibly controlled by an external electric field.13C NMR signal is shown to change over ~400 ppm (~37G for μ6-C atom together withn. Thereby, the metal cluster [Re12μ6-CS17(CN6] n−can be considered as a perspective model of a molecular switch.

Examination of rotator cuff re-tear

International Nuclear Information System (INIS)

Kitahara, Hiroyuki; Yabe, Yoshihiro; Norimatsu, Takahiro; Adachi, Shinji; Sera, Keisuke

2010-01-01

The six-month post-operative re-tear rate in 72 arthroscopic rotator cuff repair cases was 16.3% by MRI. The re-tear rate of massive tears was 50%. We investigated the details of the re-tears by MRI and arthroscopic findings. High re-tear rates were connected with cuff tear size and fatty degeneration of muscle belly. Cases with poor cuff quality in arthroscopically showed high re-tear rate. These results suggest that surgery operation should be performed as soon as possible after diagnosis of cuff tear to obtain good results. Cases with damage of long head of the biceps (LHB) are likely to develop impingement causes of re-tears. Some type of rehabilitation is required to avoid impingement in such cases. (author)

The Impact of Family Engagement and Child Welfare Services on Maltreatment Re-reports and Substantiated Re-reports.

Science.gov (United States)

Fuller, Tamara; Zhang, Saijun

2017-08-01

Despite decades of debate about the most effective ways to intervene with families reported to child protective services (CPS), little evidence exists regarding the types of services or approach that reduce children's risk of additional maltreatment. The current study used data collected during a statewide experimental evaluation of CPS to examine the impact of numerous service variables, family engagement, and family characteristics on the risk of maltreatment re-reports and substantiated re-reports among families initially reported for neglect and risk of harm. The sample included 4,868 families with screened-in reports that were randomly assigned to receive either an investigation or an assessment. The results of the Cox regression analyses found that service duration, intensity, and breadth were unrelated to maltreatment re-report or substantiated re-reports, but caseworker ratings of the service-need match were associated with both. The provision of domestic violence services was related to decreased risk of maltreatment re-reports. Increased levels of family engagement were associated with lowered risk of both maltreatment re-reports and substantiated re-reports. Once the effects of services, engagement, and family characteristics were taken into account, CPS response pathway (investigation or assessment) had no relationship to maltreatment re-reports or substantiated re-reports.

Insights into Andean metallogenesis from the perspective of Re-Os analyses of sulfides

International Nuclear Information System (INIS)

Mathur, R.; Ruiz, J.R; Munizaga, F.M

2001-01-01

The source of metals and duration of mineralization for ore deposits are basic issues used to describe the metallogenesis of an area. In order to address these fundamental issues in the Andean Cordillera, we chose to analyze Re-Os isotopes in sulfides from twelve porphyry copper ore deposits that are spatially and temporally separated. Re-Os concentrates in sulfide minerals, and can thus provide genetic information on the source of metals and the timing of mineralization. The advantage of using Re-Os isotopes is that genetic and geochronologic information is obtained directly from the sulfide ore mineral, rather than by inferring chemical relationships from possibly unrelated alteration silicates. In this study we use the source of Os in low concentration sulfides as a proxy for the source of base metals. Initial ratios greater than the chondritic mantle (∼0.13) serve as indication of a crustal source for Os and, by inference, other ore forming metals. Molybdenite contains orders of magnitude more Re than the common sulfides and effectively no initial radiogenic 187 Os (Luck and Allegre, 1982). Therefore, it can be used as a high-precision geochronometer (McCandless, 1994; Stein et al. 1997). Re-Os data from low concentration sulfides and chronologic data from high concentration molybdenites highlight important processes within and among these Andean deposits.The low concentration sulfides contain between 5-30 ppt Os and 1- 30 ppb Re. There are two samples of hydrothermal and magmatic magnetite from Escondida that contain slightly more Re and Os than the other sulfides reported. The molybdenites have 187 Os concentrations that range from 5-2000 ppb, and Re concentrations that range from 60-3600 ppm. Mathur et al. (2000) and Mathur (2000) highlighted a strong relationship between the copper tonnage in Andean ore deposits and the Os initial ratio of sulfide minerals. The larger deposits have sulfide minerals with lower initial Os ratios than the smaller, less

Sports video games: re-shaping football and re-defining fandom?

OpenAIRE

ervine bangor ac uk, j.

2017-01-01

This paper will examine ways in which football video games, such as Football Manager and FIFA, are re- shaping the sport of football and re-defining the relationship between fans and the sport. In so doing, it will explore ways in which football video games have been portrayed in both the UK and France through close study of the press, academic literature, the press and popular culture.To begin with, it will be argued that dismissive attitudes of some journalists and football managers towards...

CH3-ReO3 on gamma-Al2O3: understanding its structure, initiation,and reactivity in olefin metathesis

Energy Technology Data Exchange (ETDEWEB)

Salameh, Alain; Joubert, Jerome; Baudouin, Anne; Lukens, Wayne; Delbecq, Francoise; Sautet, Philippe; Basset, Jean Marie; Coperet,Christophe

2007-01-20

Me-ReO3 on gamma-alumina: understanding the structure, theinitiation and thereactivity of a highly active olefin metathesiscatalyst Heterolytic splitting of the C-H bond of the methyl group ofCH3ReO3 on AlsO reactive sites of alumina as a way to generate the activesite of CH3ReO3 supported on gamma-Al203.

Detection and quantification of ginsenoside Re in ginseng samples by a chromatographic immunostaining method using monoclonal antibody against ginsenoside Re.

Science.gov (United States)

Morinaga, Osamu; Tanaka, Hiroyuki; Shoyama, Yukihiro

2006-01-02

A chromatographic immunostaining method has been developed for the determination of ginsenoside Re (G-Re) in ginseng samples on a polyethersulphone (PES) membrane. G-Re standard and the extracts of ginseng roots were applied to a PES membrane and developed by methanol-water-acetic acid (45:55:1, by volume). G-Re was clearly detected by an immunostaining method using a monoclonal antibody against G-Re. The coloring spots of G-Re were analyzed quantitatively using NIH Image software indicating at least 0.125 microg of G-Re was detectable. G-Re can be analyzed quantitatively between 0.25 and 4.0 microg.

Calculation and evaluation of the activation cross sections for 187Re(n,2n)186m,gRe reactions

International Nuclear Information System (INIS)

Huang Xiaolong; Lu Hanlin; Zhou Chunmei

1998-01-01

The activation cross sections for 187 Re(n,2n) 186m,g Re reactions are calculated using UNF code. The calculations are in good agreement with the re-evaluated measured data. Finally the excitation function for 187 Re(n,2n) 186m,g Re reactions are evaluated and recommended based on present calculations and evaluated decay data

Investigation of the transport properties and compositions of the Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5} series (RE=Pr, Sm, Gd, Dy; Pn=Sb, Bi)

Energy Technology Data Exchange (ETDEWEB)

Forbes, Scott [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4M1 (Canada); Yuan, Fang [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4M1 (Canada); Institute for Materials Science, 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan); Kosuda, Kosuke; Kolodiazhnyi, Taras [Institute for Materials Science, 1-1 Namiki, Tsukuba, Ibaraki 305-0044 (Japan); Mozharivskyj, Yurij, E-mail: mozhar@mcmaster.ca [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4M1 (Canada)

2016-10-15

The Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5} phases (RE=Pr, Sm, Gd, Dy; Pn=Sb, Bi) were successfully prepared from high temperature reactions at 1225–1300 °C. These phases maintain the same structure types as the parent RE{sub 9}Pn{sub 5}O{sub 5} phases, except for a Ca/RE mixing. The study and preparation of these phases was motivated by the desire to shift the metallic type properties of the parent RE{sub 9}Pn{sub 5}O{sub 5} phases to a level more suitable for thermoelectric applications. Electrical resistivity measurements performed on pure, bulk samples indicated all phases to be narrow band gap semiconductors or semimetals, supporting the charge balanced electron count of the Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5} composition. Unfortunately, all samples are too electrically resistive for any potential usage as thermoelectrics. Electronic band structure calculations performed on idealized RE{sub 9}Pn{sub 5}O{sub 5} structures revealed the presence of a pseudogap at the Fermi level, which is consistent with the observed electrical resistivity and Seebeck coefficient behavior. - Graphical abstract: Ca substitution in RE{sub 9}Pn{sub 5}O{sub 5} leads to charge-balanced Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5} phases with semiconducting or semimetallic properties. - Highlights: • The RE{sub 9}Pn{sub 5}O{sub 5} structure may be stabilized with calcium substitution in the form of Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5}. • The Ca{sub 2}RE{sub 7}Pn{sub 5}O{sub 5} phases maintain the parent P 4/n structure, albeit with Ca/RE mixing. • The Ca{sub 2}RE{sub 7}Sb{sub 5}O{sub 5} phases behave as semiconductors while Ca{sub 2}RE{sub 7}Bi{sub 5}O{sub 5} are semimetals with electron-electron correlations. • Electronic structure calculations yield a semimetal-like density of states for both Ca{sub 2}RE{sub 7}Sb{sub 5}O{sub 5} and Ca{sub 2}RE{sub 7}Bi{sub 5}O{sub 5}.

First principles electronic and thermal properties of some AlRE intermetallics

Science.gov (United States)

Srivastava, Vipul; Sanyal, Sankar P.; Rajagopalan, M.

2008-10-01

A study on structural and electronic properties of non-magnetic cubic B 2-type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grüneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grüneisen model and compared with the others’ theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics.

First principles electronic and thermal properties of some AlRE intermetallics

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Vipul [Department of Physics, Barkatullah University, Hoshangabad Road, Bhopal, Madhya Pradesh 462 026 (India)], E-mail: vips73@yahoo.com; Sanyal, Sankar P. [Department of Physics, Barkatullah University, Hoshangabad Road, Bhopal, Madhya Pradesh 462 026 (India); Rajagopalan, M. [Department of Physics, Anna University, Chennai-600 025 (India)

2008-10-01

A study on structural and electronic properties of non-magnetic cubic B{sub 2}-type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grueneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grueneisen model and compared with the others' theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics.

First principles electronic and thermal properties of some AlRE intermetallics

International Nuclear Information System (INIS)

Srivastava, Vipul; Sanyal, Sankar P.; Rajagopalan, M.

2008-01-01

A study on structural and electronic properties of non-magnetic cubic B 2 -type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grueneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grueneisen model and compared with the others' theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics

The Re-Think Tree.

Science.gov (United States)

Gear, Jim

1993-01-01

The Re-Think Tree is a simple framework to help individuals assess and improve their behaviors related to environmental issues. The branches of the tree in order of priority are refuse, reduce, re-use, and recycle. Roots of the tree include such things as public opinion, education, and watchdog groups. (KS)

Re-use of disposable coil dialysers

International Nuclear Information System (INIS)

Abbud Filho, M.

1980-01-01

Re-use of disposable dialysers has been in practice for over 16 years throughout the world but it still is a polemical subject. The main justification for it is the reduction of costs in the hemodialytic treatment. We evaluated the technique of re-use that we adopt by studying 33 patients who should re-utilize coil dialysers for 8 consecutive hemodialysis sessions. We investigated: 1) small and middle molecules clearances trough a radioisotopic method; 2) the integrity of the system regarding bacterial invasion; 3) the frequency of anti-N antibodies; 4) aspects of scanning electron microscopy (SEM) of dialysis membrane after re-use. We observed no changes in the dialysers performance during re-use. We conclude that the re-use of dialyzers is feasible, without risks for the patients, allowing marked reduction of costs, thus making possible to offer treatment to a larger number of uremic patients. (author)

Effects of abutment diameter, luting agent type, and re-cementation on the retention of implant-supported CAD/CAM metal copings over short abutments.

Science.gov (United States)

Safari, Sina; Hosseini Ghavam, Fereshteh; Amini, Parviz; Yaghmaei, Kaveh

2018-02-01

The aim of this study was to evaluate the effects of abutment diameter, cement type, and re-cementation on the retention of implant-supported CAD/CAM metal copings over short abutments. Sixty abutments with two different diameters, the height of which was reduced to 3 mm, were vertically mounted in acrylic resin blocks with matching implant analogues. The specimens were divided into 2 diameter groups: 4.5 mm and 5.5 mm (n=30). For each abutment a CAD/CAM metal coping was manufactured, with an occlusal loop. Each group was sub-divided into 3 sub-groups (n=10). In each subgroup, a different cement type was used: resin-modified glass-ionomer, resin cement and zinc-oxide-eugenol. After incubation and thermocycling, the removal force was measured using a universal testing machine at a cross-head speed of 0.5 mm/min. In zinc-oxide-eugenol group, after removal of the coping, the cement remnants were completely cleaned and the copings were re-cemented with resin cement and re-tested. Two-way ANOVA, post hoc Tukey tests, and paired t-test were used to analyze data (α=.05). The highest pulling force was registered in the resin cement group (414.8 N), followed by the re-cementation group (380.5 N). Increasing the diameter improved the retention significantly ( P =.006). The difference in retention between the cemented and recemented copings was not statistically significant ( P =.40). Resin cement provided retention almost twice as strong as that of the RMGI. Increasing the abutment diameter improved retention significantly. Re-cementation with resin cement did not exhibit any difference from the initial cementation with resin cement.

Charge Carrier Trapping Processes in RE2O2S (RE = La, Gd, Y, and Lu)

NARCIS (Netherlands)

Luo, H.; Bos, A.J.J.; Dorenbos, P.

2017-01-01

Two different charge carrier trapping processes have been investigated in RE2O2S:Ln3+ (RE = La, Gd, Y, and Lu; Ln = Ce, Pr, and Tb) and RE2O2S:M (M = Ti4+ and Eu3+). Cerium, praseodymium and terbium act as recombination centers and hole trapping centers while host intrinsic defects provide the

Equiatomic indides REIrIn (RE=La, Pr, Nd, Er-Yb). Crystal and electronic structure

Energy Technology Data Exchange (ETDEWEB)

Zaremba, Nazar [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Technische Univ. Muenchen, Garching (Germany). Fakultaet fuer Chemie; Muts, Ihor; Zaremba, Vasyl [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Hlukhyy, Viktor [Technische Univ. Muenchen, Garching (Germany). Fakultaet fuer Chemie; Stein, Sebastian; Rodewald, Ute C.; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Pavlyuk, Volodymyr [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Czestochowa Jan Dlugosz Univ., Czestochowa (Poland). Inst. of Chemistry, Environmental Protection and Biotechnology

2017-10-01

The equiatomic rare earth iridium indides REIrIn (RE=La, Pr, Nd, Er-Yb) were synthesized by reaction of the elements in induction or muffle furnaces and were characterized through X-ray powder patterns. The structures of LaIr{sub 0.86}In{sub 1.14}, PrIr{sub 0.89}In{sub 1.11}, NdIr{sub 0.94}In{sub 1.06}, ErIrIn (all ZrNiAl type, P anti 62m), and YbIrIn (TiNiSi type, Pnma) were refined from single crystal X-ray diffractometer data. Refinements of the occupancy parameters revealed small degrees of solid solutions with indium substitution on the iridium sites. Chemical bonding analyses and electronic structure calculations indicate the dominance of metallic bonding in addition to partial ionic interactions between the cations and polyanions, as well as covalent contributions between the indium and iridium atoms.

Structural Properties and UV-Visible Absorption Spectroscopy of Retinal-pyridyl-CN Re(I) Carbonyl Bipyridine Complex: A Theoretical Study.

Science.gov (United States)

Eng, Julien; Daniel, Chantal

2015-10-29

The structural, electronic, and optical properties of the all-trans and five cis conformers of [Re(CO)3(bpy)(ret-pyr-CN)](+) (bpy = 2,2'-bipyridine; ret-pyr-CN = pyridyl-CN-3,7-dimethyl-9-(2,6,6-trimethylcyclohex-2-n)-none-(2,4,6,8-tetraen) were studied in solvent by means of density functional theory (DFT) and time-dependent DFT. The isolated retinal-like chromophore ret-pyr-CN was investigated as well for comparison. By coordination to the complex the two lowest intraligand (IL) states localized on the retinal group are slightly red-shifted from 627 to 690 nm and from 415 to 450 nm, respectively. Several isomerization pathways are open upon irradiation of the Re(I) complex by visible light (400-450 nm), especially to two cis conformers corresponding to the isomerization of the two double bonds of the retinal-like ligand close to the pyridyl group linked to the Re(I) fragment. The metal-to-ligand charge transfer states localized either on the retinal group or on the bpy ligand should play a minor role in the isomerization process itself but could improve its efficiency via ultra-fast intersystem crossing.

Critical systematic evaluation and thermodynamic optimization of the Mn–RE system: RE = La, Ce, Pr, Nd and Sm

International Nuclear Information System (INIS)

Kim, Junghwan; Jung, In-Ho

2012-01-01

Highlights: ► The Mn–RE (RE = La, Ce, Pr, Nd and Sm) systems have been critically reviewed. ► The thermodynamic optimization of the Mn–RE systems have been performed. ► Systematic changes in the phase diagrams and thermodynamic properties were found. ► The systematic approach resolved inconsistencies in the experimental data. - Abstract: Critical evaluation and optimization of all available phase diagram and thermodynamic data for the Mn–RE (RE = La, Ce, Pr, Nd and Sm) systems have been conducted to obtain reliable thermodynamic functions of all the phases in the system. In the thermodynamic modeling, it is found that the Mn–RE systems show systematic changes in the phase diagrams and thermodynamic properties such as enthalpy of mixing in liquid state in the order of periodic number in the lanthanide series. This systematic thermodynamic modeling approach for all light RE elements can allow to resolve inconsistencies in the experimental data.

Polarization sensitive behaviour of the band-edge transitions in ReS2 and ReSe2 layered semiconductors

International Nuclear Information System (INIS)

Ho, C H; Lee, H W; Wu, C C

2004-01-01

The polarization sensitive behaviour of the band-edge transitions in ReS 2 and ReSe 2 layered compounds was studied using polarized-transmission and polarized-thermoreflectance (PTR) measurements with polarization angles from θ = 0 deg. (Evector parallel b-axis) to θ = 90 deg. (Evector perpendicular b-axis) at 300 K. The polarization dependence of the polarized energy gaps of ReS 2 and ReSe 2 shows a sinusoidal-like variation with respect to the angular change of the linearly polarized light. The angular dependences of the polarized energy gaps of ReS 2 and ReSe 2 were evaluated. The polarization sensitive behaviour of the band-edge excitons in rhenium disulfide and diselenide was characterized using angular dependent PTR measurements from θ = 0 deg. to 90 deg. The polarized transition intensities of the band-edge excitons (E 1 ex and E 2 ex ) of ReX 2 (X = S, Se) demonstrate a sinusoidal variation with respect to the angular change of the linearly polarized light. The angular dependence of the polarized transition probabilities of E 1 ex and E 2 ex is analysed. The polarization sensitive behaviours of ReX 2 (X = S, Se) layers are discussed

Re-design, re-use and recycle of temporary houses

Energy Technology Data Exchange (ETDEWEB)

Arslan, Hakan [Department of Construction, Faculty of Technical Education, University of Abant Izzet Baysal, Duzce 81100 (Turkey)

2007-01-15

Disasters are recurring to global problems, which results in homelessness. The affected region had economical, environmental and social problems as well. In relief and reconstruction phases, the need for integrated management appeared in order to use the national sources actively and productively. Especially housing implementations had an important role for future development of the affected region. For accelerating the reconstruction of the region and forming a sustainable community, which maintains itself socially, environmentally and economically over time; energy usage for construction should be kept to a minimum. Past research in Turkey shows that the cost of temporary houses (to be used as the short term shelter) had a ratio of 10-15% of the total expenses of whole construction activity. For saving money and protecting the environment and conserving scarce resources, the affected region must consider the option of temporary houses to meet their short and long-term need during the reconstruction process. After the end of usage, temporary houses should be able to be re-used for the same or new function. This study is a test of re-design and re-use of a temporary housing site; by using recycled materials, minimum energy and voluntary participation so that this site can finally become a permanent housing site. (author)

Intricate Resonant Raman Response in Anisotropic ReS2.

Science.gov (United States)

McCreary, Amber; Simpson, Jeffrey R; Wang, Yuanxi; Rhodes, Daniel; Fujisawa, Kazunori; Balicas, Luis; Dubey, Madan; Crespi, Vincent H; Terrones, Mauricio; Hight Walker, Angela R

2017-10-11

The strong in-plane anisotropy of rhenium disulfide (ReS 2 ) offers an additional physical parameter that can be tuned for advanced applications such as logic circuits, thin-film polarizers, and polarization-sensitive photodetectors. ReS 2 also presents advantages for optoelectronics, as it is both a direct-gap semiconductor for few-layer thicknesses (unlike MoS 2 or WS 2 ) and stable in air (unlike black phosphorus). Raman spectroscopy is one of the most powerful characterization techniques to nondestructively and sensitively probe the fundamental photophysics of a 2D material. Here, we perform a thorough study of the resonant Raman response of the 18 first-order phonons in ReS 2 at various layer thicknesses and crystal orientations. Remarkably, we discover that, as opposed to a general increase in intensity of all of the Raman modes at excitonic transitions, each of the 18 modes behave differently relative to each other as a function of laser excitation, layer thickness, and orientation in a manner that highlights the importance of electron-phonon coupling in ReS 2 . In addition, we correct an unrecognized error in the calculation of the optical interference enhancement of the Raman signal of transition metal dichalcogenides on SiO 2 /Si substrates that has propagated through various reports. For ReS 2 , this correction is critical to properly assessing the resonant Raman behavior. We also implemented a perturbation approach to calculate frequency-dependent Raman intensities based on first-principles and demonstrate that, despite the neglect of excitonic effects, useful trends in the Raman intensities of monolayer and bulk ReS 2 at different laser energies can be accurately captured. Finally, the phonon dispersion calculated from first-principles is used to address the possible origins of unexplained peaks observed in the Raman spectra, such as infrared-active modes, defects, and second-order processes.

Structural, electronic, superconducting and mechanical properties of ReC and TcC

Energy Technology Data Exchange (ETDEWEB)

Kavitha, M.; Priyanga, G. Sudha; Rajeswarapalanichamy, R., E-mail: rajeswarapalanichamy@gmail.com; Santhosh, M. [Department of Physics, N.M.S.S.V.N College, Madurai, Tamilnadu-625019 (India)

2015-06-24

The structural, electronic, superconducting and mechanical properties of ReC and TcC are investigated using density functional theory calculations. The lattice constants, bulk modulus, and the density of states are obtained. The calculated lattice parameters are in good agreement with the available results. The density of states reveals that ReC and TcC exhibit metallic behavior at ambient condition. A pressure-induced structural phase transition is observed in both materials.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

Energy Technology Data Exchange (ETDEWEB)

Lu, Zhao; Zhang, Lijun [Central South Univ., Changsha (China). State Key Lab of Powder Metallurgy; Tang, Ying [Thermo-Calc Software AB, Solna (Sweden)

2017-06-15

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

International Nuclear Information System (INIS)

Lu, Zhao; Zhang, Lijun

2017-01-01

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Crystal structure and Mössbauer studies of the isotypic Fe6-cluster compounds RE15[Fe8C25], RE=Dy, Ho

KAUST Repository

Davaasuren, Bambar

2015-05-01

The carboferrates RE15[Fe8C25] (RE=Dy, Ho) were prepared from mixtures of the elements by arc-melting followed with subsequent annealing at 1373 K. The crystal structures were determined from single crystal X-ray diffraction data and revealed an isotypic relationship to Er15[Fe8C25] (hP48, P321). The main feature of the crystal structure is given by Fe6 cluster units characterized by covalent Fe-Fe bonding interactions. 57Fe Mössbauer spectra of Dy15[Fe8C25] were fitted by three subspectra with relative spectral weights of about 3:3:2 which is in general agreement with the crystal structure. Below 50 K, an onset of magnetic hyperfine fields at the three iron sites is observed which is supposed to be caused by dipolar fields arising from neighboring, slowly relaxing Dy magnetic moments.

Development of Premacy Hydrogen RE Hybrid

Energy Technology Data Exchange (ETDEWEB)

Wakayama, N. [Mazda Motor Corporation, Hiroshima (Japan)

2010-07-01

Hydrogen powered ICE (internal combustion engine) vehicles can play an important role as an automotive power source in the future, because of its higher reliability and cost performance than those of fuel cell vehicles. Combined with hydrogen, Mazda's unique rotary engine (RE) has merits such as a prevention of hydrogen pre-ignition. Mazda has been developing hydrogen vehicles with the hydrogen RE from the early 1990s. Premacy (Mazda5) Hydrogen RE Hybrid was developed and launched in 2009, following RX-8 Hydrogen RE delivered in 2006. A series hybrid system was adopted in Premacy Hydrogen RE Hybrid. A traction motor switches its windings while the vehicle is moving. This switching technology allows the motor to be small and high-efficient. The lithium-ion high voltage battery, which has excellent input-output characteristics, was installed. These features extend the hydrogen fuel driving range to 200 km and obtain excellent acceleration performance. The hydrogen RE can be also operated by gasoline (Dual Fuel System). The additional gasoline operation makes hydrogen vehicles possible to drive in non-hydrogen station area. With approval from the Japanese Ministry of Land Infrastructure and Transport, Mazda Premacy Hydrogen RE Hybrid was delivered successfully to the Japanese market in the form of leasing. (orig.)

First-principles study on the structure, elastic properties, hardness and electronic structure of TMB4 (TM=Cr, Re, Ru and Os) compounds

International Nuclear Information System (INIS)

Pan, Y.; Zheng, W.T.; Guan, W.M.; Zhang, K.H.; Fan, X.F.

2013-01-01

The structural formation, elastic properties, hardness and electronic structure of TMB 4 (TM=Cr, Re, Ru and Os) compounds are investigated using first-principles approach. The value of C 22 for these compounds is almost two times bigger than the C 11 and C 33 . The intrinsic hardness, shear modulus and Young's modulus are calculated to be in a sequence of CrB 4 >ReB 4 >RuB 4 >OsB 4 , and the Poisson's ratio and B/G ratio of TMB 4 follow the order of CrB 4 4 4 4 . The intrinsic hardness of CrB 4 and ReB 4 by LDA is bigger than 40 GPa. The high hardness of TMB 4 compounds is derived from the feature of B–B bonds cage and higher C 22 value. The B–B covalent bonds as bonds cage enhances the resistance to shear deformation and improve the hardness. We predict that the TMB 4 compounds with CrB 4 -type are the potential superhard materials. - Graphical abstract: The first-principles calculations show that the intrinsic hardness of CrB 4 and ReB 4 are bigger than 40 GPa, which are the potential superhard materials due to the B–B bonds cage structure. Display Omitted - Highlights: • The intrinsic hardness of CrB 4 and ReB 4 is bigger than 40 GPa. • The hardness of TMB 4 is calculated to be in a sequence of CrB 4 >ReB 4 >RuB 4 >OsB 4 . • The trend of hardness for TMB 4 is consistent with the variation of elastic modulus. • The C 22 value of TMB 4 is bigger than that of C 11 and C 33 . • The high hardness of TMB 4 is originated from the B–B bonds cage

(Re)politicising and (re)positioning prevention: community ...

African Journals Online (AJOL)

They also signal a need to critically re-evaluate “community mobilisation” as an AIDS prevention tradition. Intersecting social and political power dynamics play a significant role in both opening up and constraining community mobilisation efforts. This paper proposes the need for a pedagogical turn to “deep organising” and ...

Rare-earth transition-metal intermetallics: Structure-bonding-property relationships

Energy Technology Data Exchange (ETDEWEB)

Han, M. K. [Iowa State Univ., Ames, IA (United States)

2006-01-01

The explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding property relationships. The work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe_13-xSi_x system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn{sub 13}-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides Re_2-xFe₄Si_14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi₂: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb₃Zn_3.6Al_7.4: Partially ordered structure of Tb₃Zn_3.6Al_7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn₃₉(Cr_xAl_1-x)₈₁

Rare-Earth Transition-Metal Intermetallics: Structure-bonding-Property Relationships

Energy Technology Data Exchange (ETDEWEB)

Han, Mi-Kyung [Iowa State Univ., Ames, IA (United States)

2006-01-01

Our explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding-property relationships. Our work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe_13-xSi_x system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn₁₃-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides RE_2-xFe₄Si_14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi₂: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb₃Zn_3.6Al_7.4: Partially ordered structure of Tb_3.6Zn_13-xAl_7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn₃₉(Cr_xAl_1-x

Re-admissions, re-operations and length of stay in hospital after aseptic revision knee replacement in Denmark

DEFF Research Database (Denmark)

Lindberg-Larsen, M.; Jørgensen, C. C.; Hansen, Torben Bæk

2014-01-01

of hospital stay was four days (interquartile range: 3 to 5), with a 90 days re-admission rate of 9.9%, re-operation rate of 3.5% and mortality rate of 0.2%. The age ranges of 51 to 55 years (p = 0.018), 76 to 80 years (p re-admission...

Structural, elastic, electronic and dynamical properties of OsB and ReB: Density functional calculations

Science.gov (United States)

Li, Yanling; Zeng, Zhi; Lin, Haiqing

2010-06-01

The structural, elastic, electronic and dynamical properties of ReB and OsB are investigated by first-principles calculations based on density functional theory. It turns out that ReB and OsB are metallic ultra-incompressible solids with small elastic anisotropy and high hardness. The change of c/ a ratio in OsB indicates that there is a structural phase transition at about 31 GPa. Phonon spectra calculations show that both OsB and ReB are stable dynamically and there are abnormal phonon dispersions along special directions in Brillouin zone. OsB and ReB do not show superconductivity due to very weak electron-phonon interactions in them.

Effects of abutment diameter, luting agent type, and re-cementation on the retention of implant-supported CAD/CAM metal copings over short abutments

Science.gov (United States)

Safari, Sina; Amini, Parviz; Yaghmaei, Kaveh

2018-01-01

PURPOSE The aim of this study was to evaluate the effects of abutment diameter, cement type, and re-cementation on the retention of implant-supported CAD/CAM metal copings over short abutments. MATERIALS AND METHODS Sixty abutments with two different diameters, the height of which was reduced to 3 mm, were vertically mounted in acrylic resin blocks with matching implant analogues. The specimens were divided into 2 diameter groups: 4.5 mm and 5.5 mm (n=30). For each abutment a CAD/CAM metal coping was manufactured, with an occlusal loop. Each group was sub-divided into 3 sub-groups (n=10). In each subgroup, a different cement type was used: resin-modified glass-ionomer, resin cement and zinc-oxide-eugenol. After incubation and thermocycling, the removal force was measured using a universal testing machine at a cross-head speed of 0.5 mm/min. In zinc-oxide-eugenol group, after removal of the coping, the cement remnants were completely cleaned and the copings were re-cemented with resin cement and re-tested. Two-way ANOVA, post hoc Tukey tests, and paired t-test were used to analyze data (α=.05). RESULTS The highest pulling force was registered in the resin cement group (414.8 N), followed by the re-cementation group (380.5 N). Increasing the diameter improved the retention significantly (P=.006). The difference in retention between the cemented and recemented copings was not statistically significant (P=.40). CONCLUSION Resin cement provided retention almost twice as strong as that of the RMGI. Increasing the abutment diameter improved retention significantly. Re-cementation with resin cement did not exhibit any difference from the initial cementation with resin cement. PMID:29503708

Status report on seismic re-evaluation

International Nuclear Information System (INIS)

1998-01-01

In May 1997, a meeting of the PWG 3 Sub Group on the Seismic Behaviour of Structures agreed several priority objectives, of which one was the production of a status report on seismic re-evaluation. Seismic re-evaluation is identified as the process of carrying out a re-assessment of the safety of existing nuclear power plants for a specified seismic hazard. This may be necessary when no seismic hazard was considered in the original design of the plant, the relevant codes and regulations have been revised, the seismic hazard for the site has been re-assessed or there is a need to assess the capacity of the plant for severe accident conditions and behaviour beyond the design basis. Re-evaluation may also be necessary to resolve an issue, or to assess the impact of new findings or knowledge. A questionnaire on the subject was issued to all members of the Seismic Sub Group in the summer of 1997, and responses to the questionnaire had been received from most members by the end of 1997. This report is based on the responses to the questionnaire, together with comment and discussion within the group. The questionnaire covered the following main topics of interest in relation to seismic re-evaluation: General and Legislative Framework, Overall Approach, Input Definition and Analysis Methods, Scope of Plant and Assessment of As-built Situation, Assessment criteria, Outcome of Re-evaluations, Research. The responses to the questionnaire have been collated and reviewed with the objective of comparing current practice in the field of seismic re-evaluation in member countries, and a number of important points have been identified in relation to the position of seismic re-evaluation in the nuclear power industry throughout the world. It is evident that seismic re-evaluation is a relatively mature process that has been developing for some time, with most countries adopting similar practices, often based on principles which have been developed in the US nuclear industry. Seismic

Ternary rare-earth bismuthides RE5SiBi2 and RE5GeBi2 (RE=La-Nd, Gd-Er): Stabilization of the β-Yb5Sb3-type structure through tetrel substitution

International Nuclear Information System (INIS)

Barry, Stephen D.; Tkachuk, Andriy V.; Bie, Haiying; Blanchard, Peter E.R.; Mar, Arthur

2011-01-01

Ternary bismuthides RE 5 TtBi 2 containing rare-earth (RE=La-Nd, Gd-Er) and tetrel (Tt=Si, Ge) atoms have been prepared by arc-melting of the elements followed by annealing at 800 o C. They adopt the β-Yb 5 Sb 3 -type structure (Pearson symbol oP32, space group Pnma, Z=4), as revealed through analysis by single-crystal X-ray diffraction on Ce 5 Si 0.869(4) Bi 2.131(4) and powder X-ray diffraction on Ce 5 GeBi 2 . Cell parameters for the entire series lie in the ranges of a=12.8-11.8 A, b=9.6-9.0 A, and c=8.4-7.9 A. Solid solubility in Ce 5 Si x Bi 3-x and Pr 5 Si x Bi 3-x (approximately 0.9≤x≤1.2, depending on the RE member) is much more limited compared to the antimonides, consistent with a highly ordered structure in which the two possible anion sites are essentially segregated into a smaller one occupied by Tt atoms (CN7) and a larger one occupied by Bi atoms (CN9). Band structure calculations on La 5 SiBi 2 confirm the importance of La-La bonding interactions near the Fermi level. X-ray photoelectron spectra support the presence of partially anionic Bi atoms, as indicated by a small negative binding energy shift relative to elemental Bi. The Ce and Pr members undergo magnetic transitions at low temperatures, possibly involving ferromagnetic interactions, that are strongly influenced by the nature of the Tt atom. -- Graphical Abstract: Tetrel (Si or Ge) and Bi atoms are arranged in an ordered manner in the β-Yb 5 Sb 3 -type structure adopted by RE 5 TtBi 2 . Display Omitted

InSpiRe - Intelligent Spine Rehabilitation

DEFF Research Database (Denmark)

Bøg, Kasper Hafstrøm; Helms, Niels Henrik; Kjær, Per

Rapport on InSpiRe-projektet: InSpiRe er et nationalt netværk, der skal fremme mulighederne for intelligent genoptræning i forhold til ryglidelser. I netværket mødes forskere, virksomheder, kiropraktorer og fysioterapeuter for at udvikle nye genoptrænings og/eller behandlingsteknologier.......Rapport on InSpiRe-projektet: InSpiRe er et nationalt netværk, der skal fremme mulighederne for intelligent genoptræning i forhold til ryglidelser. I netværket mødes forskere, virksomheder, kiropraktorer og fysioterapeuter for at udvikle nye genoptrænings og/eller behandlingsteknologier....

Ternary silicides ScIr{sub 4}Si{sub 2} and RERh{sub 4}Si{sub 2} (RE = Sc, Y, Tb-Lu) and quaternary derivatives RERh{sub 4}Si{sub 2-x}Sn{sub x} (RE = Y, Nd, Sm, Gd-Lu) - structure, chemical bonding, and solid state NMR spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Vosswinkel, Daniel; Benndorf, Christopher; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Eckert, Hellmut [Muenster Univ. (Germany). Inst. fuer Physikalische Chemie; Sao Paulo Univ., Sao Carlos (Brazil). Inst. of Physics; Matar, Samir F. [Bordeaux Univ., CNRS, ICMCB, UPR 9048, Pessac (France)

2016-11-01

The silicides ScIr{sub 4}Si{sub 2} and RERh{sub 4}Si{sub 2} (RE = Sc, Y, Tb-Lu) and silicide stannides RERh{sub 4}Si{sub 2-x}Sn{sub x}(RE = Y, Nd, Sm, Gd-Lu) were synthesized from the elements by arc-melting and subsequent annealing. The new compounds crystallize with the orthorhombic YRh{sub 4}Ge{sub 2} type structure, space group Pnma. They were characterized by X-ray powder patterns and several structures were refined from single crystal X-ray diffractometer data. The main structural motifs of this series of silicides are tricapped trigonal prisms formed by the transition metal and rare earth atoms. One of the two crystallographically independent silicon sites allows for formation of solid solutions with tin, exemplarily studied for ErRh{sub 4}Si{sub 2-x}Sn{sub x}. Electronic structure calculations reveal strong covalent Rh-Si bonding as the main stability factor. Multinuclear ({sup 29}Si, {sup 45}Sc, and {sup 89}Y) magic-angle spinning (MAS) NMR spectra of the structure representatives with diamagnetic rare-earth elements (Sc, Y, Lu) are found to be consistent with the crystallographic data and specifically confirm the selective substitution of Sn in the Si2 sites in the quaternary compounds YRh{sub 4}SiSn and LuRh{sub 4}SiSn.

Re-dispersion of alumina particles in water: influence of the surface state

International Nuclear Information System (INIS)

Desset, Sabine

1999-01-01

The aim of this work was to determine the mechanisms by which suspensions of alpha alumina particles may be dried and then re-dispersed spontaneously in water. To get reproducible results, we designed appropriate protocols: (i) for preparing the surface state, and for generating controlled interparticle contacts (presence of water or complexing agents); (ii) for measuring the amount of re-dispersed material with a proper averaging over all interparticle bonds (turbidity). These results show that there are thresholds, determined by the conditions of drying and re-dispersion, where all the powder goes from the aggregated state to the dispersed state. With hydrated powders, it was found that mild changes in the chemical conditions (pH) and application of very weak mechanical forces (sedimentation) were enough to cause significant change in re-dispersion. According to these thresholds, a re-dispersion mechanism could be identified. Re-dispersion is ruled, indeed, by a balance of forces and the displacement of the re-dispersion thresholds indicates a shift in the balance of forces. These forces are the well known forces that control colloidal stability: van der Waals attraction, electrostatic repulsion and hydration forces. We found that hydration acts as a repulsive wall corresponding to one or two monolayers of water on each surface and depends on the Relative Humidity of drying. We also found that electrostatic repulsions at short separations are much weaker than the predictions based on the Poisson Boltzmann equation, but should be modelled according to the triple layer model. Repulsions to be considered are those calculated with the screened charges of the particles. Another aim of this work was to facilitate re-dispersion by using complexing agents that bind to the surfaces and add a steric repulsion We have found that molecules with carboxylic and hydroxyl groups can be efficient in this respect, if they are bound to surfaces before aggregation, if they are not

Re-dispersion of alumina particles in water: influence of the surface state

International Nuclear Information System (INIS)

Desset, Sabine

1999-01-01

The aim of this work was to determine the mechanisms by which suspensions of alpha alumina particles may be dried and then re-dispersed spontaneously in water. To get reproducible results, we designed appropriate protocols: (i) for preparing the surface state, and for generating controlled interparticle contacts (presence of water or complexing agents); (ii) for measuring the amount of re-dispersed material with a proper averaging over all interparticle bonds (turbidity). These results show that there are thresholds, determined by the conditions of drying and re-dispersion, where all the powder goes from the aggregated state to the dispersed state. With hydrated powders, it was found that mild changes in the chemical conditions (pH) and application of very weak mechanical forces (sedimentation) were enough to cause significant change in re-dispersion. According to these thresholds, a re-dispersion mechanism could be identified. Re-dispersion is ruled, indeed, by a balance of forces and the displacement of the re-dispersion thresholds indicates a shift in the balance of forces. These forces are the well-known forces that control colloidal stability: van der Waals attraction, electrostatic repulsion and hydration forces. We found that hydration acts as a repulsive wall corresponding to one or two monolayers of water on each surface and depends on the Relative Humidity of drying. We also found that electrostatic repulsions at short separations are much weaker than the predictions based on the Poisson Boltzmann equation, but should be modelled according to the triple layer model. Repulsions to be considered are those calculated with the screened charges of the particles. Another aim of this work was to facilitate re-dispersion by using complexing agents that bind to the surfaces and add a steric repulsion We have found that molecules with carboxylic and hydroxyl groups can be efficient in this respect, if they are bound to surfaces before aggregation, if they are not

Concentration of 188Re-Perrhenate for Therapeutic Radiopharmaceuticals

International Nuclear Information System (INIS)

Bokhari, T.H.; Hina, S.; Ahmad, M.; Iqbal, M.

2013-01-01

Summary: Rhenium-188 (T1/2=16.9h) has great potential for a variety of therapeutic applications, including radionuclide synovectomy, oncology and bone pain palliation. The radioactive concentration of 188Re is dependent upon the specific activity of 188W, which dictates the bed size of the alumina/gel column. Due to the high content of inactive tungsten in neutron irradiated WO3, large columns containing aluminum oxide or gel are needed to prepare to double neutron capture based 188W/188Re generators that results in large elution volumes containing relatively high188W contents and low concentrations of /sup 188/ ReO/sub 4/ This decrease in specific volume of 188ReO/sub 4/ places a limitation because a high radioactive concentration of 188ReO4 - is always needed for filling angioplasty balloons or other therapeutic radiopharmaceuticals like188Re -EHDP 188Re -EDTMP, 188Re - MAG3 and 188Re -DTPA. We report post elution concentration of 188ReO4 - using in- house prepared lead cation exchange and alumina columns. Using these columns high bolus volume (10 mL saline) of 188ReO4 - can conveniently be concentrated in 1 mL of physiological saline for therapeutic use. (author)

Thermolysis of salts of [ReCl6]2- and [ReBr6]2- anions

International Nuclear Information System (INIS)

Gubanov, A.I.; Korenev, S.V.; Gromilov, S.A.; Shubin, Yu.V.

2003-01-01

Thermal decomposition of the [Pd(NH 3 ) 4 ][ReG 6 ], [Pt(NH 3 ) 4 ][ReG 6 ], (NH 4 ) 2 [ReG 6 ] complexes, where G = Cl, Br, was studied in the inert atmosphere. Certain regularities of the thermolysis were established. Finished products of the thermolysis of binary complexes in the inert atmosphere were demonstrated to be two-phase systems containing two solid solutions - one on the basis of the platinum (palladium) fcc-lattice, another - on the basis of the rhenium hcp lattice. One-phase solid palladium - rhenium solutions were established to be obtained during reduction of the studied complexes in the hydrogen atmosphere [ru

Quaternary germanides RE{sub 3}TRh{sub 4}Ge{sub 4} (RE = Ce, Pr, Nd; T = Nb, Ta) - a new coloring variant of the aristotype AlB{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, Rolf-Dieter; Vosswinkel, Daniel; Poettgen, Rainer [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster, Corrensstrasse 30, 48149 Muenster (Germany); Matar, Samir F. [CNRS, Universite de Bordeaux, ICMCB, UPR 9048, 33600 Pessac (France)

2016-09-15

The quaternary germanides RE{sub 3}TRh{sub 4}Ge{sub 4} (RE = Ce, Pr, Nd; T = Nb, Ta) were synthesized from the elements by arc-melting and subsequent annealing in a muffle furnace. The structure of Ce{sub 3}TaRh{sub 4}Ge{sub 4} was refined from single-crystal X-ray diffractometer data: new type, Pbam, a = 719.9(2), b = 1495.0(3), c = 431.61(8), wR{sub 2} = 0.0678, 1004 F{sup 2} values, and 40 variables. Isotypy of the remaining phases was evident from X-ray powder patterns. Ce{sub 3}TaRh{sub 4}Ge{sub 4} is a new superstructure variant of the aristotype AlB{sub 2} with an ordering of cerium and tantalum on the aluminum site, whereas the honey-comb network is built up by a 1:1 ordering of rhodium and germanium. This crystal-chemical relationship is discussed based on a group-subgroup scheme. The distinctly different size of tantalum and cerium leads to a pronounced puckering of the [Rh{sub 4}Ge{sub 4}] network, which shows the shortest interatomic distances (253-271 pm Rh-Ge) within the Ce{sub 3}TaRh{sub 4}Ge{sub 4} structure. Another remarkable structural feature concerns the tantalum coordination with six shorter Ta-Rh bonds (265-266 pm) and six longer Ta-Ge bonds (294-295 pm). The [Rh{sub 4}Ge{sub 4}] network fully separates the tantalum and cerium atoms (Ce-Ce > 387 pm, Ta-Ta > 431 pm, and Ce-Ta > 359 pm). The electronic density of states DOS from DFT calculations show metallic behavior with large contributions of localized Ce 4f as well as itinerant ones from all constituents at the Fermi level but no significant magnetic polarization on Ce could be identified. The bonding characteristics described based on overlap populations illustrate further the crystal chemistry observations of the different coordination of Ce1 and Ce2 in Ce{sub 3}TaRh{sub 4}Ge{sub 4}. The Rh-Ge interactions within the network are highlighted as dominant. The bonding magnitudes follow the interatomic distances and identify differences of Ta bonding vs. Ce1/Ce2 bonding with the Rh and Ge

Espectro infrarrojo de [zn(mh34](re042 com substituicion isotópica 14n/15n

Directory of Open Access Journals (Sweden)

Claudio Téllez

1983-11-01

Full Text Available The infrared spectra of [Zn(15NH34] (Re042 and the isotopoc shift 14N/15N (Zn-n for the metal-ligand band, is reportedInforma-se o espectro infravermelho do complexo de Zn(II, [Zn(15NH341(Re04 e o deslocamento isotópico 14N/15N, para a banda metal - ligante v(Zn-N.

Design analysis of a Helium re-condenser

Science.gov (United States)

Muley, P. K.; Bapat, S. L.; Atrey, M. D.

2017-02-01

Modern helium cryostats deploy a cryocooler with a re-condenser at its II stage for in-situ re-condensation of boil-off vapor. The present work is a vital step in the ongoing research work of design of cryocooler based 100 litre helium cryostat with in-situ re-condensation. The cryostat incorporates a two stage Gifford McMahon cryocooler having specified refrigerating capacity of 40 W at 43 K for I stage and 1 W at 4.2 K for II stage. Although design of cryostat ensures thermal load for cryocooler below its specified refrigerating capacity at the second stage, successful in-situ re-condensation depends on proper design of re-condenser which forms the objective of this work. The present work proposes design of helium re-condenser with straight rectangular fins. Fins are analyzed for optimization of thermal performance parameters such as condensation heat transfer coefficient, surface area for heat transfer, re-condensing capacity, efficiency and effectiveness. The present work provides design of re-condenser with 19 integral fins each of 10 mm height and 1.5 mm thickness with a gap of 1.5 mm between two fins, keeping in mind the manufacturing feasibility, having efficiency of 80.96 % and effectiveness of 10.34.

India RE Grid Integration Study

Energy Technology Data Exchange (ETDEWEB)

Cochran, Jaquelin M [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-08

The use of renewable energy (RE) sources, primarily wind and solar generation, is poised to grow significantly within the Indian power system. The Government of India has established a target of 175 gigawatts (GW) of installed RE capacity by 2022, including 60 GW of wind and 100 GW of solar, up from 29 GW wind and 9 GW solar at the beginning of 2017. Thanks to advanced weather and power system modeling made for this project, the study team is able to explore operational impacts of meeting India's RE targets and identify actions that may be favorable for integration.

The effect of reactive ion etch (RIE) process conditions on ReRAM device performance

Science.gov (United States)

Beckmann, K.; Holt, J.; Olin-Ammentorp, W.; Alamgir, Z.; Van Nostrand, J.; Cady, N. C.

2017-09-01

The recent surge of research on resistive random access memory (ReRAM) devices has resulted in a wealth of different materials and fabrication approaches. In this work, we describe the performance implications of utilizing a reactive ion etch (RIE) based process to fabricate HfO2 based ReRAM devices, versus a more unconventional shadow mask fabrication approach. The work is the result of an effort to increase device yield and reduce individual device size. Our results show that choice of RIE etch gas (SF6 versus CF4) is critical for defining the post-etch device profile (cross-section), and for tuning the removal of metal layers used as bottom electrodes in the ReRAM device stack. We have shown that etch conditions leading to a tapered profile for the device stack cause poor electrical performance, likely due to metal re-deposition during etching, and damage to the switching layer. These devices exhibit nonlinear I-V during the low resistive state, but this could be improved to linear behavior once a near-vertical etch profile was achieved. Device stacks with vertical etch profiles also showed an increase in forming voltage, reduced switching variability and increased endurance.

Transition metal-centered trigonal prisms as building units in RE{sub 14}T{sub 3}In{sub 3} (RE = Y, Ho, Er, Tm, Lu; T = Pd, Ir, Pt) and Y{sub 4}IrIn

Energy Technology Data Exchange (ETDEWEB)

Zaremba, R.; Rodewald, U.C.; Poettgen, R. [Inst. fuer Anorganische und Analytische Chemie, Univ. Muenster (Germany)

2007-12-15

The indides RE{sub 14}T{sub 3}In{sub 3} (RE = Y, Ho, Er, Tm, Lu; T = Pd, Ir, Pt) and Y{sub 4}IrIn were synthesized from the elements by are-melting and subsequent annealing for crystal growth. Their structures were characterized on the basis of X-ray powder and single crystal data: Lu{sub 14}Co{sub 3}In{sub 3}-type, space group P4{sub 2}/nmc, a = 970.2(1), c = 2340.7(5) pm for Y{sub 13.95}Pd{sub 3}In{sub 3.05}, a = 959.7(1), c = 2309.0(5) pm for Ho{sub 14}Pd{sub 2.95}In{sub 3}, a = 955.5(1), c = 2305.1(5) pm for Er{sub 14}Pd{sub 3}In{sub 3}, a = 950.9(1), c = 2291.6(5) pm for Tm{sub 13.90}Pd{sub 3}In{sub 3.10}, a = 944.4(1), c = 2275.5(5) pm for Lu{sub 13.93}Pd{sub 3}In{sub 3.07}, a = 962.9(1), c = 2343.0(5) pm for Y{sub 13.86}Ir{sub 2.97}In{sub 3.02}, a = 967.6(1), c = 2347.8(5) pm for Y{sub 13.92}Pt{sub 3.05}In{sub 2.91}, and Gd{sub 4}RhIn-type, space group F anti 43m, a = 1368.6(2) pm for Y{sub 4}IrIn. The main structural motifs are transition metal-centered trigonal prisms of the rare Earth elements which are condensed to two-dimensional networks in the RE{sub 14}T{sub 3}In{sub 3} indides and to a three-dimensional one in Y{sub 4}IrIn. The indium atoms in both structure types show segregation in the metal-rich matrix, i.e. In{sub 2} dumbbells in the RE{sub 14}T{sub 3}In{sub 3} indides (309 pm In2-In2 in Y{sub 13.86}Ir{sub 2.97}In{sub 3.02}) and In{sub 4} tetrahedra (322 pm In-In) in Y{sub 4}IrIn. The crystal chemical peculiarities of both structure types are discussed. (orig.)

Simulation of the ATV Re-Entry Obsrvations

Science.gov (United States)

Bastida Virgili, B.; Krag, H.; Lips, T.; De Pasquale, E.

2010-09-01

The first ATV was launched on 9th March 2008 and, after a successful mission, the last phase was a controlled destructive re-entry on 29th September 2008, shortly after 13:30 UTC, in which the remains of the ATV and its load fell into the South Pacific Ocean. In order to better understand the re-entry processes, an insitu optical observation campaign was launched to record and analyze the ATV controlled re-entry with several instruments on board of two airplanes and also from the ISS. This observation campaign was successful and triggered several different still-ongoing studies on the extraction and analysis of data to draw conclusions on the adequacy of the re-entry break-up and explosion models used for the safety analysis of the ATV re-entry. This paper addresses the validation process for ESA’s model for re-entry survivability and on-ground risk assessment for explosive re-entry events using the observation data. The underlying rationale is to improve the models for the benefit of planning and execution of future controlled re-entries and in risk calculation in case of uncontrolled ones. The re-entry trajectory of the ATV, the explosive event and the trajectories of the fragments are simulated with the existing ESA tools and the EVOLVE explosion model. Additional software has been developed to simulate airborne sensor field of view(FOV) crossings based on the aircraft trajectories, attitude profile, sensor mounts and FOVs. Sensor performance and object radiation are modeled in order to generate synthetic images for the different sensors in the ISS and the two airplanes. These synthetic images and synthetic videos are compared with the available reentry observations of the ATV. This paper will present the software and techniques to generate synthetic imagery. It will give results of the comparison between the simulated and the real trajectories and fragmentation and explain the subsequent validation process of the ESA re-entry tools and the potential

L-acetylcarnitine enhances functional muscle re-innervation.

Science.gov (United States)

Pettorossi, V E; Brunetti, O; Carobi, C; Della Torre, G; Grassi, S

1991-01-01

The efficacy of L-acetylcarnitine and L-carnitine treatment on motor re-innervation was analyzed by evaluating different muscular parameters describing functional muscle recovery after denervation and re-innervation. The results show that L-acetylcarnitine markedly enhances functional muscle re-innervation, which on the contrary is unaffected by L-carnitine. The medial gastrocnemius muscle was denervated by cutting the nerve at the muscle entry point. After 20 days the sectioned nerve was resutured into the medial gastrocnemius muscle, and the extent of re-innervation was monitored 45 days later. L-acetylcarnitine-treated animals show significantly higher twitch and tetanic tensions of re-innervated muscle. Furthermore the results, obtained by analysing the twitch time to peak and tetanic contraction-relaxation times, suggest that L-acetylcarnitine mostly affects the functional re-innervation of slow motor units. The possible mechanisms by which L-acetylcarnitine facilitates such motor and nerve recovery are discussed.

Immobilization of {sup 99}Tc (Re) using Iron-Phosphate Glasses

Energy Technology Data Exchange (ETDEWEB)

Heo, Jong; Xu, Kai; Um, Woo Yong; Hrma, Pavel [Pohang Univ. of Science and Technology, Pohang (Korea, Republic of)

2012-05-15

Technetium-99 ({sup 99}Tc) is a fission product artificially generated during the irradiation of {sup 235}U for commercial power production or {sup 239}Pu for nuclear weapons. Under oxidizing conditions, the dominant species of Tc, the pertechnetate anion (TcO{sub 4} {sup -}), is highly soluble in ground water and thus easily transports through the geologic systems. In addition, because of its high fission yield ({approx}6 %) and long half-life (2.1x10{sup 5} yr), immobilization of {sup 99}Tc has been investigated for decades. Several waste forms such as metallic alloys, sintered titanate ceramics and chemically bonded phosphate ceramics have been proposed to encapsulate {sup 99}Tc. They have not yet been realized in the industrial-scale, mostly either due to the high volatilization of {sup 99}Tc during high temperature process (>1300 .deg. C), or the low {sup 99}Tc loading. Iron-phosphate (FeP) glasses have been developed as alternative waste forms because of their chemical durability equivalent to borosilicate glasses. Additionally, vitrification of radioactive waste by FeP glasses can be done at a relatively low temperature ({approx}1000 .deg. C) and the low-temperature process can reduce the volatilization of {sup 99}Tc significantly. Thus, this work reports the immobilization of {sup 99}Tc by FeP glasses using rhenium (Re) as a surrogate. We also examine the chemical durability of Re-containing FeP glasses using product consistency test (PCT). Experimental results reveal that FeP glass can become a promising candidate for immobilizing {sup 99}Tc

Comparative NMR investigation of the Re-based borides

Science.gov (United States)

Lue, C. S.; Tao, Y. F.; Su, T. H.

2008-07-01

We report a systematic study of the rhenium-based borides, ReB2 , Re7B3 , and Re3B , by means of the B11 nuclear magnetic resonance (NMR) spectroscopy. While Re7B3 and Re3B are superconductors, ReB2 exhibits no superconducting signature but is of current interest due to its superhard mechanical property. Since the major focus of this investigation is their electronic characteristics in the normal states, we performed the measurements at temperatures between 77 and 295 K. For Re7B3 and Re3B , s -character electrons were found to be responsible for the observed B11 NMR Knight shift and spin-lattice relaxation rate (1/T1) . From T1 analysis, we thus deduce the partial Bs Fermi-level density of states (DOS) of both borides. On the other hand, the relaxation rate of ReB2 is mainly associated with p electrons, similar to the cases of OsB2 and RuB2 . In addition, the extracted B2p Fermi-level DOS is in good agreement with the theoretical prediction from band-structure calculations.

Voyage dans le noir. Trous noirs, matière noire, énergie noire et antimatière

CERN Multimedia

CERN. Geneva; Alvarez-Gaume, Luis; Grojean, Christophe

2009-01-01

Et si nous faisions avec les physiciens un voyage dans le noir ? De l'astrophysique à la physique des particules les trois noirs, la matière noire, l'énergie noire ou l’antimatière intriguent et fascinent. Que sont ces objets qui bousculent nos idées et qui véhiculent parfois des craintes irraisonnées? Luis Alvarez-Gaume, Michael Doser et Christophe Grojean, physiciens du CERN vous invitent à mettre en lumière (!) les constituants de base de la matière et à explorer les mystères de la physique contemporaine. Une soirée lumineuse pour éclairer des concepts et ne plus avoir peur du noir.

Allele Re-sequencing Technologies

DEFF Research Database (Denmark)

Byrne, Stephen; Farrell, Jacqueline Danielle; Asp, Torben

2013-01-01

The development of next-generation sequencing technologies has made sequencing an affordable approach for detection of genetic variations associated with various traits. However, the cost of whole genome re-sequencing still remains too high to be feasible for many plant species with large...... alternative to whole genome re-sequencing to identify causative genetic variations in plants. One challenge, however, will be efficient bioinformatics strategies for data handling and analysis from the increasing amount of sequence information....

Biomolecule labelling by 186 Re

International Nuclear Information System (INIS)

Lungu, Valeria Viorica; Mihailescu, Gabriela; Dumitrescu, Gabriela

1998-01-01

The aim of this study is to develop and improve the existing radiolabelling techniques of peptides and monoclonal antibodies with 186 Re and 188 Re as potential agents for cancer targeted radiotherapy. We selected the following methods and techniques for direct labelling of peptides and monoclonal antibody: 1. Prereduction of -S-S- bridges of biomolecule to sulfhydryls using reducing agents: ascorbic acid, cysteine, active hydrogen, 2,3 dimercaptopropanol. The prereduction reactions are controlled by massic ratios of reduction agents/biomolecule, pH, temperature and time of incubation; 2. Reduction of 186 Re O 4 - stannous chloride in acid and alkaline pH; 3. Coupling reaction of 186 Re (red) with the biomolecule controlled by the time and temperature of incubation, the influence of pH regarding the binding of 186 Re to the biomolecules. The quality control was effected by chromatography techniques (paper and elution gel chromatography) on labeled biomolecule before and after purification. The elution gel chromatography was spectrophotometricaly monitored at 280 nm. In the same time the radioactivity of samples was measured using a gamma counter. All the results confirm in vitro stability of labeled biomolecule. The biological evaluation studies regarding accumulation and biological affinity will be controlled by scintigraphy method. Biodistribution studies will be effected to Walker tumor bearing animals at 4 and 24 hours after injections. (authors)

99Tc and Re incorporated into metal oxide polyoxometalates: oxidation state stability elucidated by electrochemistry and theory.

Science.gov (United States)

McGregor, Donna; Burton-Pye, Benjamin P; Mbomekalle, Israel M; Aparicio, Pablo A; Romo, Susanna; López, Xavier; Poblet, Josep M; Francesconi, Lynn C

2012-08-20

The radioactive element technetium-99 ((99)Tc, half-life = 2.1 × 10(5) years, β(-) of 253 keV), is a major byproduct of (235)U fission in the nuclear fuel cycle. (99)Tc is also found in radioactive waste tanks and in the environment at National Lab sites and fuel reprocessing centers. Separation and storage of the long-lived (99)Tc in an appropriate and stable waste-form is an important issue that needs to be addressed. Considering metal oxide solid-state materials as potential storage matrixes for Tc, we are examining the redox speciation of Tc on the molecular level using polyoxometalates (POMs) as models. In this study we investigate the electrochemistry of Tc complexes of the monovacant Wells-Dawson isomers, α(1)-P(2)W(17)O(61)(10-) (α1) and α(2)-P(2)W(17)O(61)(10-) (α2) to identify features of metal oxide materials that can stabilize the immobile Tc(IV) oxidation state accessed from the synthesized Tc(V)O species and to interrogate other possible oxidation states available to Tc within these materials. The experimental results are consistent with density functional theory (DFT) calculations. Electrochemistry of K(7-n)H(n)[Tc(V)O(α(1)-P(2)W(17)O(61))] (Tc(V)O-α1), K(7-n)H(n)[Tc(V)O(α(2)-P(2)W(17)O(61))] (Tc(V)O-α2) and their rhenium analogues as a function of pH show that the Tc-containing derivatives are always more readily reduced than their Re analogues. Both Tc and Re are reduced more readily in the lacunary α1 site as compared to the α2 site. The DFT calculations elucidate that the highest oxidation state attainable for Re is VII while, under the same electrochemistry conditions, the highest oxidation state for Tc is VI. The M(V)→ M(IV) reduction processes for Tc(V)O-α1 are not pH dependent or only slightly pH dependent suggesting that protonation does not accompany reduction of this species unlike the M(V)O-α2 (M = (99)Tc, Re) and Re(V)O-α1 where M(V/IV) reduction process must occur hand in hand with protonation of the terminal M═O to

Chemical Vapor Deposition Growth of Degenerate p-Type Mo-Doped ReS2 Films and Their Homojunction.

Science.gov (United States)

Qin, Jing-Kai; Shao, Wen-Zhu; Xu, Cheng-Yan; Li, Yang; Ren, Dan-Dan; Song, Xiao-Guo; Zhen, Liang

2017-05-10

Substitutional doping of transition metal dichalcogenide two-dimensional materials has proven to be effective in tuning their intrinsic properties, such as band gap, transport characteristics, and magnetism. In this study, we realized substitutional doping of monolayer rhenium disulfide (ReS 2 ) with Mo via chemical vapor deposition. Scanning transmission electron microscopy demonstrated that Mo atoms are successfully doped into ReS 2 by substitutionally replacing Re atoms in the lattice. Electrical measurements revealed the degenerate p-type semiconductor behavior of Mo-doped ReS 2 field effect transistors, in agreement with density functional theory calculations. The p-n diode device based on a doped ReS 2 and ReS 2 homojunction exhibited gate-tunable current rectification behaviors, and the maximum rectification ratio could reach up to 150 at V d = -2/+2 V. The successful synthesis of p-type ReS 2 in this study could largely promote its application in novel electronic and optoelectronic devices.

Neutron diffraction studies on structural and magnetic properties of RE2NiGe3 (RE=La, Ce)

International Nuclear Information System (INIS)

Kalsi, Deepti; Rayaprol, S.; Siruguri, V.; Peter, Sebastian C.

2014-01-01

We report the crystallographic properties of RE 2 NiGe 3 (RE=La, Ce) synthesized by arc melting. Rietveld refinement on the powder neutron diffraction (ND) data suggest both compounds are isostructural and crystallize in the non-centrosymmetric Er 2 RhSi 3 type structure having hexagonal space group P6 ¯ 2c. In the crystal structure of RE 2 NiGe 3 , two dimensional arrangements of nickel and germanium atoms lead to the formation of hexagonal layers with rare earth atoms sandwiched between them. Magnetic susceptibility measurements performed in low fields exhibit antiferromagnetic ordering in cerium compound around (T o =) 3.2 K. Neutron diffraction measurements at 2.8 K (i.e., at TRE 2 NiGe 3 (RE=La, Ce) crystallize in the ordered superstructure of the AlB 2 type. Magnetic susceptibility measurements exhibit antiferromagnetic ordering in Ce 2 NiGe 3 . Structure and magnetism of RE 2 NiGe 3 (RE=La, Ce) are studied by neutron diffraction

Recurring Anomaly Detection System (ReADS)

Data.gov (United States)

National Aeronautics and Space Administration — Overview: ReADS can analyze text reports, such as aviation reports and problem or maintenance records. ReADS uses text clustering algorithms to group loosely related...

The self-activation and synergy of amorphous Re nanoparticle – Si nanowire composites for the electrocatalytic hydrogen evolution

International Nuclear Information System (INIS)

Yang, Lulu; Lu, Shunkai; Wang, Hui; Shao, Qi; Liao, Fan; Shao, Mingwang

2017-01-01

Highlights: • Amorphous Re nanoparticle modified Si nanowire nanocomposites were prepared. • An interesting self-activation phenomenon was observed in HER process. • Re/SiNW showed synergy in HER process. • The optimal mass ratio of Re: Si was determined to be 31.1: 68.9. - Abstract: Amorphous rhenium nanoparticles modified silicon nanowires were prepared via reducing Re ion by Si−H bonds, which were employed to electrocatalysize the hydrogen evolution reaction because amorphous structure may have excellent catalytic activity. It is interesting that an obvious self-activation for Re/Si catalysts was observed with the current density enhanced by 2.2 times its previous value at 400 mV after a 3,000 s of continuous cyclic voltammetry scanning, and the catalytic performance remained steady thereafter. The optimal electrocatalytic performance was found with the Re: Si mass ratio of 31.1: 68.9, resulting in a Tafel slope of 81 mV·dec −1 and overpotential of 100 mV at current density of 10 mA·cm −2 .

Split Fermi Surfaces of the Spin-Orbit-Coupled Metal Cd2Re2O7 Probed by de Haas-van Alphen Effect

Science.gov (United States)

Matsubayashi, Yasuhito; Sugii, Kaori; Hirose, Hishiro T.; Hirai, Daigorou; Sugiura, Shiori; Terashima, Taichi; Uji, Shinya; Hiroi, Zenji

2018-05-01

The superconducting pyrochlore oxide Cd2Re2O7 shows a structural transition with inversion symmetry breaking (ISB) at Ts1 = 200 K. A recent theory [https://doi.org/10.1103/PhysRevLett.115.026401" xlink:type="simple">L. Fu, Phys. Rev. Lett. 115, 026401 (2015)] suggests that the origin is an electronic instability that leads to a multipolar order in the spin-orbit-coupled metal. To observe the Fermi surface of the low-temperature phase of Cd2Re2O7, we perform de Haas-van Alphen effect measurements by means of magnetic torque. In reference to a calculated band structure, the spin-split Fermi surfaces with large cyclotron masses of 5-9m0 are revealed. The splitting is suggested to be due to an antisymmetric spin-orbit coupling induced by ISB, the strength of which is estimated to be approximately 67 K, which is rather smaller than those of typical non-centrosymmetric metals.

Synthesis of complex compounds in the system [ReOG5]2--thiosemicarbazone acetone-Hg-acetone

International Nuclear Information System (INIS)

Amindzhanov, A.A.; Kurbanov, N.M.

1993-01-01

Present article is devoted to synthesis of complex compounds in the system [ReOG 5 ] 2- -thiosemicarbazone acetone-Hg-acetone. The literature data on complex compounds of various metals with thiosemicarbazone was summarized. The synthesis of complex compounds in the system [ReOG 5 ] 2- -thiosemicarbazone acetone-Hg-acetone was conducted. The complex compounds of rhenium with methyl ident thiosemicarbazone were synthesized.

Familiære abdominale aortaaneurismer

DEFF Research Database (Denmark)

Mejnert Jørgensen, Trine; Lindholt, Jes S.; Høgh, Annette Langager

Formål og baggrund: Det er velkendt, at risikoen for at udvikle et abdominalt aortaaneurisme (AAA) er væsentligt forøget blandt førstegradsslægtninge til AAA-patienter, men tidligere studier er få og svært sammenlignelige, ligesom man ikke har kunnet belyse, om familiære tilfælde af AAA fremtræder...... mere aggressivt end ikke-familiære. Man ved således meget lidt om væksthastighed, prognose for ruptur, alder ved diagnose og operation og risiko for AAA-relaterede dødsfald for denne gruppe. Projektet vil forsøge at besvare følgende: Hvor stor er forekomsten af AAA blandt førstegradsslægtninge til AAA......-patienter på landsplan og er familiære tilfælde af AAA mere aggressive i form af lavere gennemsnitsalder ved diagnose og operation, hurtigere vækstrate, større rupturrisiko og højere forekomst af AAA-relaterede dødsfald end ikke-familiære AAA? Design: Projektet er et retrospektivt case-kontrolstudie, hvor man...

RE-Powering’s Electronic Decision Tree

Science.gov (United States)

Developed by US EPA's RE-Powering America's Land Initiative, the RE-Powering Decision Trees tool guides interested parties through a process to screen sites for their suitability for solar photovoltaics or wind installations

Business process re-engineering in service operations

International Nuclear Information System (INIS)

McClintock, J.W.

1995-01-01

The concept of business process re-engineering, and how it was applied to the operations of the Consumers Gas Company were discussed. Business process re-engineering was defined as the improvement of the efficiency of the customer-service process, and the overall improvement of practices and operations. The re-engineering project was said to involve a thorough analysis of information technology, current limitations, and business operational needs, undertaken on an enterprise-wide basis. Viewed generically,a re-engineering project was said to have six major components: (1) business drivers (i.e. the articulation of the Company's strategic issues); (2) benchmark measures; (3) future state process models; (4) cost/benefit analysis; (5) a change management plan; and (6) a development plan. Business improvements expected to result from the project include reduced cost of operation, reduction of waste, and a substantially complete re-design of the business process. Management of the project involved a team approach, and help of a consultant to identify the scope of the re-design, its limitations, and future state. A life expectancy of approximately 10 years was given for the re-engineering plan, with annual benefits (in terms of cost reduction) of $4.6 million by the year 2000

Space-Efficient Re-Pair Compression

DEFF Research Database (Denmark)

Bille, Philip; Gørtz, Inge Li; Prezza, Nicola

2017-01-01

Re-Pair [5] is an effective grammar-based compression scheme achieving strong compression rates in practice. Let n, σ, and d be the text length, alphabet size, and dictionary size of the final grammar, respectively. In their original paper, the authors show how to compute the Re-Pair grammar...... in expected linear time and 5n + 4σ2 + 4d + √n words of working space on top of the text. In this work, we propose two algorithms improving on the space of their original solution. Our model assumes a memory word of [log2 n] bits and a re-writable input text composed by n such words. Our first algorithm runs...

Cohesion of BaReH₉ and BaMnH₉: Density Functional Calculations and Prediction of (MnH₉)^2- Salts

Energy Technology Data Exchange (ETDEWEB)

Singh, David J [ORNL; Gupta, Michele [Universite Paris Sud, Orsay, France; Gupta, Raju [CEA, Saclay, France

2007-01-01

Density functional calculations are used to calculate the structural and electronic properties of BaReH9 and to analyze the bonding in this compound. The high coordination in BaReH9 is due to bonding between Re 5d states and states of d-like symmetry formed from combinations of H s orbitals in the H9 cage. This explains the structure of the material, its short bond lengths and other physical properties, such as the high band gap. We compare with results for hypothetical BaMnH9, which we find to have similar bonding and cohesion to the Re compound. This suggests that it may be possible to synthesize (MnH9)2- salts. Depending on the particular cation, such salts may have exceptionally high hydrogen contents, in excess of 10 weight %.

Magnetoelastic coupling in Sr2(Fe1-xCrx)ReO6 double perovskites

International Nuclear Information System (INIS)

Serrate, D; Teresa, J M De; Algarabel, P A; Marquina, C; Blasco, J; Ibarra, M R; Galibert, J

2007-01-01

We have investigated magnetoelastic coupling in Sr 2 (Fe 1-x Cr x )ReO 6 polycrystalline double perovskites. The end compound, Sr 2 CrReO 6 , shows a high ferromagnetic transition temperature of 635 K and is thought to exhibit a nearly half-metallic conduction band. We probed the unexpected high orbital moment borne by the Re atom by means of volume and anisotropic magnetostriction measurements in magnetic fields up to 12 T. Our magnetostriction results can be explained by the existence of a large spin-orbit coupling which, in combination with crystal-field effects, produces a single-ion type magnetostrictive response. The Re orbital moment triggers a greatly enhanced magnetocrystalline anisotropy compared to other ferromagnetic double perovskites. From our magnetostriction data, the temperature dependence of the coercive field as a function of Cr-doping is obtained. We discovered that the coercive field increases as Fe is replaced with Cr, which is linked to a strong enhancement of the magnetic anisotropy. This suggests a close relationship between the Fe[Cr]-O-Re coupling and the magnetic anisotropy. We also analysed the impact of the Re orbital moment on the spin-dependent transport across Sr 2 CrReO 6 grain boundaries. The present work opens up the possible use of these compounds for magnetostrictive applications in a wide temperature and magnetic field range

Studies on the preparation and isomeric composition of [sup 186]Re- and [sup 188]Re-pentavalent rhenium dimercaptosuccinic acid complex

Energy Technology Data Exchange (ETDEWEB)

Singh, J. (Canterbury Univ. (United Kingdom). Biological Lab.); Reghebi, K.; Lazarus, C.R.; Clarke, S.E.M. (Guy' s Hospital, London (United Kingdom)); Callahan, A.P.; Knapp, F.F. Jr. (Oak Ridge National Lab., TN (United States)); Blower, P.J. (Kent and Canterbury Hospital (United Kingdom))

1993-03-01

The preparative conditions for [sup 186]Re(V)DMSA and [sup 188]Re(V)DMSA (DMSA = meso-dimercaptosuccinic acid), [beta]-emitting radiopharmaceuticals that have been shown to localize in medullary thyroid carcinoma, require modification depending on the amount of carrier rhenium and the chemical form and medium in which the rhenium is supplied. Preparative conditions are described for use with carrier-free [sup 188]ReO[sub 4][sup -] in saline, and for use with [sup 186]ReO[sub 4][sup -] in saline, sodium hydroxide or nitric acid. Preparation of [sup 186]Re(V)DMSA (carrier present up to 2 mg per 2.5 ml reaction volume) requires a DMSA:SnCl[sub 2]:Re ratio of 10:5:1 at 100[sup o]C for 30 min. Addition of excess nitric acid or hydrochloric acid up to a concentration of 155 mM does not reduce the yield from 100%. A commercial DMSA kit vial (e.g. Amerscan DMSA) can be used for preparation of [sup 188]Re(V)DMSA (carrier free) provided the required is in a volume of less than 1 ml per vial. A convenient method of concentrating the [sup 188]Re generator eluate to the required volume is described. (Author).

First-principles study on the structure, elastic properties, hardness and electronic structure of TMB{sub 4} (TM=Cr, Re, Ru and Os) compounds

Energy Technology Data Exchange (ETDEWEB)

Pan, Y. [Department of Materials Science, Key Laboratory of Automobile Materials of MOE and State Key Laboratory of Superhard Materials, Jilin University, Changchun 130012 (China); Zheng, W.T., E-mail: WTZheng@jlu.edu.cn [Department of Materials Science, Key Laboratory of Automobile Materials of MOE and State Key Laboratory of Superhard Materials, Jilin University, Changchun 130012 (China); Guan, W.M.; Zhang, K.H. [State Key Laboratory of Advanced Technologies for Comprehensive Utilization of Platinum Metals, Kunming 650106 (China); Fan, X.F. [Department of Materials Science, Key Laboratory of Automobile Materials of MOE and State Key Laboratory of Superhard Materials, Jilin University, Changchun 130012 (China)

2013-11-15

The structural formation, elastic properties, hardness and electronic structure of TMB{sub 4} (TM=Cr, Re, Ru and Os) compounds are investigated using first-principles approach. The value of C{sub 22} for these compounds is almost two times bigger than the C{sub 11} and C{sub 33}. The intrinsic hardness, shear modulus and Young's modulus are calculated to be in a sequence of CrB{sub 4}>ReB{sub 4}>RuB{sub 4}>OsB{sub 4}, and the Poisson's ratio and B/G ratio of TMB{sub 4} follow the order of CrB{sub 4}<ReB{sub 4}ReB{sub 4} by LDA is bigger than 40 GPa. The high hardness of TMB{sub 4} compounds is derived from the feature of B–B bonds cage and higher C{sub 22} value. The B–B covalent bonds as bonds cage enhances the resistance to shear deformation and improve the hardness. We predict that the TMB{sub 4} compounds with CrB{sub 4}-type are the potential superhard materials. - Graphical abstract: The first-principles calculations show that the intrinsic hardness of CrB{sub 4} and ReB{sub 4} are bigger than 40 GPa, which are the potential superhard materials due to the B–B bonds cage structure. Display Omitted - Highlights: • The intrinsic hardness of CrB{sub 4} and ReB{sub 4} is bigger than 40 GPa. • The hardness of TMB{sub 4} is calculated to be in a sequence of CrB{sub 4}>ReB{sub 4}>RuB{sub 4}>OsB{sub 4}. • The trend of hardness for TMB{sub 4} is consistent with the variation of elastic modulus. • The C{sub 22} value of TMB{sub 4} is bigger than that of C{sub 11} and C{sub 33}. • The high hardness of TMB{sub 4} is originated from the B–B bonds cage.

Re-irradiation for abdominal tumor. Preliminary results

International Nuclear Information System (INIS)

Narisada, Hiroyuki; Imada, Hajime; Tomoda, Yoshinori

2012-01-01

The purpose of this study was to assess the efficacy of loco-regional radiotherapy for recurrent abdominal tumor treated with re-irradiation. Re-irradiated areas of 16 patients were eight of pelvic space, five of retroperitonium and three of liver or porta hepatica. Eligibility criteria of re-irradiation were success of initial irradiation, no other effective treatment except re-irradiation, constancy of bowel gas at hunger status and respiratory movement, visceral dosage reduction at re-irradiation. Total dose of initial, second course of radiation were 51.3±10.8 Gy, 50.6±14.2 Gy, respectively. Interval of initial and second course of radiation were 16.6±10.2 months. Local control after second course of radiation was four cases of complete response, five of partial response and seven of stable disease. Median survival periods were 55 months after initial treatment and 28 months after second course of radiation. In two cases of pelvic reirradiation, skin to pelvic space fistula was occurred. Re-irradiation for abdominal tumor may become useful salvage treatment. (author)

Synthesis, Characterization, and In Vitro Evaluation of New (99m)Tc/Re(V)-Cyclized Octreotide Analogues: An Experimental and Computational Approach.

Science.gov (United States)

Li, Yawen; Ma, Lixin; Gaddam, Vikram; Gallazzi, Fabio; Hennkens, Heather M; Harmata, Michael; Lewis, Michael R; Deakyne, Carol A; Jurisson, Silvia S

2016-02-01

Radiolabeled proteolytic degradation-resistant somatostatin analogues have been of long-standing interest as cancer imaging and radiotherapy agents for targeting somatostatin receptor-positive tumors. Our interest in developing (186)Re- and (188)Re-based therapeutic radiopharmaceuticals led to investigation of a new Re(V)-cyclized octreotide analogue, Re(V)-cyclized, thiolated-DPhe(1)-Cys(2)-Tyr(3)-DTrp(4)-Lys(5)-Thr(6)-Cys(7)-Thr(OH)(8) (Re-SDPhe-TATE) using both experimental and quantum chemical methods. The metal is directly coordinated to SDPhe-TATE through cyclization of the peptide around the [ReO](3+) core. Upon complexation, four isomers were observed; the isolated/semi-isolated isomers exhibited different somatostatin receptor (sstr) binding affinities, 0.13 to 1.5 μM, in rat pancreatic tumor cells. Two-dimensional NMR experiments and electronic structure calculations were employed to elucidate the structural differences among the different isomers. According to NMR studies, the metal is coordinated to three thiolates and the backbone amide of Cys(2) in isomers 1 and 4, whereas the metal is coordinated to three thiolates and the backbone amide of Tyr(3) in isomer 2. Quantum chemical methods clarified the stereochemistry of Re-SDPhe-TATE and the possible peptide arrangements around the [ReO](3+) core. The re-cyclization reaction was translated to the (99m)Tc radiotracer level with four isomers observed on complexation with comparable HPLC retention times as the Re-SDPhe-TATE isomers. About 85% total (99m)Tc labeling yield was achieved by ligand exchange from (99m)Tc-glucoheptonate at 60 °C for an hour. About 100% and 51% of (99m)Tc(V)-cyclized SDPhe-TATE remained intact in phosphate buffered saline and 1 mM cysteine solution under physiological conditions at 6 h, respectively.

An analytical threshold voltage model for a short-channel dual-metal-gate (DMG) recessed-source/drain (Re-S/D) SOI MOSFET

Science.gov (United States)

Saramekala, G. K.; Santra, Abirmoya; Dubey, Sarvesh; Jit, Satyabrata; Tiwari, Pramod Kumar

2013-08-01

In this paper, an analytical short-channel threshold voltage model is presented for a dual-metal-gate (DMG) fully depleted recessed source/drain (Re-S/D) SOI MOSFET. For the first time, the advantages of recessed source/drain (Re-S/D) and of dual-metal-gate structure are incorporated simultaneously in a fully depleted SOI MOSFET. The analytical surface potential model at Si-channel/SiO2 interface and Si-channel/buried-oxide (BOX) interface have been developed by solving the 2-D Poisson’s equation in the channel region with appropriate boundary conditions assuming parabolic potential profile in the transverse direction of the channel. Thereupon, a threshold voltage model is derived from the minimum surface potential in the channel. The developed model is analyzed extensively for a variety of device parameters like the oxide and silicon channel thicknesses, thickness of source/drain extension in the BOX, control and screen gate length ratio. The validity of the present 2D analytical model is verified with ATLAS™, a 2D device simulator from SILVACO Inc.

Comparison of programmed and cabled re-entrance systems. Elaboration of cabled re-entrance system for a CII 90.40

International Nuclear Information System (INIS)

Perraudeau, Jean

1976-01-01

The objective of this research thesis is to study problems related to re-entrance, and, more particularly, to study a re-entrance system for a CII 90.40 computer. Such a system can be realised under a programmed or cabled form, and both approaches are described and compared. A generalisation of this comparison is briefly proposed. As the computer already possesses a programmed re-entrance system, the author focuses on the study of the cabled re-entrance system which results in an improvement of performance and possibilities provided by this computer, particularly for its use in real time. The design, realisation and development of such a cabled system are reported. A first part reports a theoretical study on re-entrance (definition, problems, applications), a presentation of the computer, a description of the programmed re-entrance system, a presentation of the principle of the chosen cabled re-entrance system, a definition of the structure and operating mode of the cabled pile and a description of its various components, and a flowchart analysis of function execution. The second part reports the practical realisation: definition, technological overview, technology used in the cabled pile, sequencing and multiplexing principle, impulse transmission, logical layouts, and circuit adjustments. The third part presents practical example. An assessment and perspectives are finally discussed

Onboard autonomous mission re-planning for multi-satellite system

Science.gov (United States)

Zheng, Zixuan; Guo, Jian; Gill, Eberhard

2018-04-01

This paper presents an onboard autonomous mission re-planning system for Multi-Satellites System (MSS) to perform onboard re-planing in disruptive situations. The proposed re-planning system can deal with different potential emergency situations. This paper uses Multi-Objective Hybrid Dynamic Mutation Genetic Algorithm (MO-HDM GA) combined with re-planning techniques as the core algorithm. The Cyclically Re-planning Method (CRM) and the Near Real-time Re-planning Method (NRRM) are developed to meet different mission requirements. Simulations results show that both methods can provide feasible re-planning sequences under unforeseen situations. The comparisons illustrate that using the CRM is average 20% faster than the NRRM on computation time. However, by using the NRRM more raw data can be observed and transmitted than using the CRM within the same period. The usability of this onboard re-planning system is not limited to multi-satellite system. Other mission planning and re-planning problems related to autonomous multiple vehicles with similar demands are also applicable.

Existing reflection seismic data re-processing

International Nuclear Information System (INIS)

Higashinaka, Motonori; Sano, Yukiko; Kozawa, Takeshi

2005-08-01

This document is to report the results of existing seismic data re-processing around Horonobe town, Hokkaido, Japan, which is a part of the Horonobe Underground Research Project. The main purpose of this re-processing is to recognize the subsurface structure of Omagari Fault and fold system around Omagari Fault. The seismic lines for re-processing are TYHR-A3 line and SHRB-2 line, which JAPEX surveyed in 1975. Applying weathering static correction using refraction analysis and noise suppression procedure, we have much enhanced seismic profile. Following information was obtained from seismic re-processing results. TYHR-A3 line: There are strong reflections, dipping to the west. These reflections are corresponding western limb of anticline to the west side of Omagari Fault. SHRB-2 line: There are strong reflections, dipping to the west, at CDP 60-140, while there are reflections, dipping to the east, to the east side of CDP 140. These reflections correspond to the western limb and the eastern limb of the anticline, which is parallel to Omagari FAULT. This seismic re-processing provides some useful information to know the geological structure around Omagari Fault. (author)

Dissecting the Re-Os molybdenite geochronometer.

Science.gov (United States)

Barra, Fernando; Deditius, Artur; Reich, Martin; Kilburn, Matt R; Guagliardo, Paul; Roberts, Malcolm P

2017-11-22

Rhenium and osmium isotopes have been used for decades to date the formation of molybdenite (MoS 2 ), a common mineral in ore deposits and the world's main source of molybdenum and rhenium. Understanding the distribution of parent 187 Re and radiogenic daughter 187 Os isotopes in molybdenite is critical in interpreting isotopic measurements because it can compromise the accurate determination and interpretation of mineralization ages. In order to resolve the controls on the distribution of these elements, chemical and isotope mapping of MoS 2 grains from representative porphyry copper-molybdenum deposits were performed using electron microprobe and nano-scale secondary ion mass spectrometry. Our results show a heterogeneous distribution of 185,187 Re and 192 Os isotopes in MoS 2 , and that both 187 Re and 187 Os isotopes are not decoupled as previously thought. We conclude that Re and Os are structurally bound or present as nanoparticles in or next to molybdenite grains, recording a complex formation history and hindering the use of microbeam techniques for Re-Os molybdenite dating. Our study opens new avenues to explore the effects of isotope nuggeting in geochronometers.

Deformation behavior of Re alloyed Mo thin films on flexible substrates: In situ fragmentation analysis supported by first-principles calculations.

Science.gov (United States)

Jörg, Tanja; Music, Denis; Hauser, Filipe; Cordill, Megan J; Franz, Robert; Köstenbauer, Harald; Winkler, Jörg; Schneider, Jochen M; Mitterer, Christian

2017-08-07

A major obstacle in the utilization of Mo thin films in flexible electronics is their brittle fracture behavior. Within this study, alloying with Re is explored as a potential strategy to improve the resistance to fracture. The sputter-deposited Mo 1-x Re x films (with 0 ≤ x ≤ 0.31) were characterized in terms of structural and mechanical properties, residual stresses as well as electrical resistivity. Their deformation behavior was assessed by straining 50 nm thin films on polyimide substrates in uniaxial tension, while monitoring crack initiation and propagation in situ by optical microscopy and electrical resistance measurements. A significant toughness enhancement occurs with increasing Re content for all body-centered cubic solid solution films (x ≤ 0.23). However, at higher Re concentrations (x > 0.23) the positive effect of Re is inhibited due to the formation of dual-phase films with the additional close packed A15 Mo 3 Re phase. The mechanisms responsible for the observed toughness behavior are discussed based on experimental observations and electronic structure calculations. Re gives rise to both increased plasticity and bond strengthening in these Mo-Re solid solutions.

The ionic conductivity and local environment of cations in Bi9ReO17

International Nuclear Information System (INIS)

Thompson, M.; Herranz, T.; Santos, B.; Marco, J.F.; Berry, F.J.; Greaves, C.

2010-01-01

The influence of temperature on the structure of Bi 9 ReO 17 has been investigated using differential thermal analysis, variable temperature X-ray diffraction and neutron powder diffraction. The material undergoes an order-disorder transition at ∼1000 K on heating, to form a fluorite-related phase. The local environments of the cations in fully ordered Bi 9 ReO 17 have been investigated by Bi L III - and Re L III -edge extended X-ray absorption fine structure (EXAFS) measurements to complement the neutron powder diffraction information. Whereas rhenium displays regular tetrahedral coordination, all bismuth sites show coordination geometries which reflect the importance of a stereochemically active lone pair of electrons. Because of the wide range of Bi-O distances, EXAFS data are similar to those observed for disordered structures, and are dominated by the shorter Bi-O bonds. Ionic conductivity measurements indicate that ordered Bi 9 ReO 17 exhibits reasonably high oxide ion conductivity, corresponding to 2.9x10 -5 Ω -1 cm -1 at 673 K, whereas the disordered form shows higher oxide ion conductivity (9.1x10 -4 Ω -1 cm -1 at 673 K). - Graphical abstract: The structure of Bi 9 ReO 17 is discussed and related to the ionic conductivity of the ordered and disordered forms.

Bond financing for renewable energy in Asia

International Nuclear Information System (INIS)

Ng, Thiam Hee; Tao, Jacqueline Yujia

2016-01-01

Addressing the financing gap for renewable energy (RE) projects in Asia is critical to ensure that the rapidly increasing energy needs could be met sustainably. This paper explores the cause of the financing gap in Asia and proposes the use of bond financing to address the financing gap. Specifically, three fixed income instruments, namely local currency denominated (LCY) corporate bonds, asset backed project bonds and financial green bonds, will be assessed. Whilst the potential for these three instruments to mobilize large flows of private sector financing is great, key supportive policies aimed at reducing the capital market bias for conventional power generation technologies and supportive RE policies are required. Another key aspect would be the necessary deepening of local and regional fixed income markets before such capital market instruments are able to play a big role. - Highlights: •This study looks at the current financing gap and RE financing landscape in developing Asia. •LCY corporate bonds, asset backed projects bonds and financial green bonds could help to address the financing gap for RE in the region. •Policy recommendations for building the fixed income market for RE projects are provided.

Processing and properties of large grain (RE)BCO

International Nuclear Information System (INIS)

Cardwell, D.A.

1998-01-01

The potential of high temperature superconductors to generate large magnetic fields and to carry current with low power dissipation at 77 K is particularly attractive for a variety of permanent magnet applications. As a result large grain bulk (RE)-Ba-Cu-O ((RE)BCO) materials have been developed by melt process techniques in an attempt to fabricate practical materials for use in high field devices. This review outlines the current state of the art in this field of processing, including seeding requirements for the controlled fabrication of these materials, the origin of striking growth features such as the formation of a facet plane around the seed, platelet boundaries and (RE) 2 BaCuO 5 (RE-211) inclusions in the seeded melt grown microstructure. An observed variation in critical current density in large grain (RE)BCO samples is accounted for by Sm contamination of the material in the vicinity of the seed and with the development of a non-uniform growth morphology at ∼4 mm from the seed position. (RE)Ba 2 Cu 3 O 7-δ (RE-123) dendrites are observed to form and bro[en preferentially within the a/b plane of the lattice in this growth regime. Finally, trapped fields in excess of 3 T have been reported in irr[iated U-doped YBCO and (RE) 1+x Ba 2-x Cu 3 O y (RE=Sm, Nd) materials have been observed to carry transport current in fields of up to 10 T at 77 K. This underlines the potential of bulk (RE)BCO materials for practical permanent magnet type applications. (orig.)

BIFOCAL STEREO FOR MULTIPATH PERSON RE-IDENTIFICATION

Directory of Open Access Journals (Sweden)

G. Blott

2017-11-01

Full Text Available This work presents an approach for the task of person re-identification by exploiting bifocal stereo cameras. Present monocular person re-identification approaches show a decreasing working distance, when increasing the image resolution to obtain a higher reidentification performance. We propose a novel 3D multipath bifocal approach, containing a rectilinear lens with larger focal length for long range distances and a fish eye lens of a smaller focal length for the near range. The person re-identification performance is at least on par with 2D re-identification approaches but the working distance of the approach is increased and on average 10% more re-identification performance can be achieved in the overlapping field of view compared to a single camera. In addition, the 3D information is exploited from the overlapping field of view to solve potential 2D ambiguities.

PTFE Additive and Re-annealing Effect on Thermoluminescence Response of CaSO4:Dy Derived from Co-precipitation Method

Science.gov (United States)

Nuraeni, Nunung; Dwi Septianto, Ricky; Iskandar, Ferry; Haryanto, Freddy; Waris, Abdul; Hiswara, Eri

2017-07-01

Effect of re-annealing treatment in thermoluminescence response of thermoluminescent dosimeter (TLD) CaSO4:Dy and CaSO4:Dy with PTFE (Polytetrafluoroethylene) addition was investigated. CaSO4:Dy was prepared by a co-precipitation method. The PTFE was added before re-annealing treatment which the mass ratio of CaSO4:Dy and PTFE was fixed to 2:3. The re-annealing treatments of the samples were done at temperature 700 °C for 1 hr. The obtained samples were characterized using a Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) to observe the molecule bonding in sample and crystal properties, respectively. From the experimental results, it was observed that the thermoluminescence intensity of CaSO4:Dy, CaSO4:Dy re-annealed at 700 °C, and CaSO4:Dy + PTFE re-annealed at 700 °C are 57.03, 75.15, and 1191.11 nC, respectively. The intensity of 700 °C-re-annealed CaSO4:Dy increased significantly after PTFE addition.

Stability Analysis for HIFiRE Experiments

Science.gov (United States)

Li, Fei; Choudhari, Meelan M.; Chang, Chau-Lyan; White, Jeffery A.; Kimmel, Roger; Adamczak, David; Borg, Matthew; Stanfield, Scott; Smith, Mark S.

2012-01-01

The HIFiRE-1 flight experiment provided a valuable database pertaining to boundary layer transition over a 7-degree half-angle, circular cone model from supersonic to hypersonic Mach numbers, and a range of Reynolds numbers and angles of attack. This paper reports selected findings from the ongoing computational analysis of the measured in-flight transition behavior. Transition during the ascent phase at nearly zero degree angle of attack is dominated by second mode instabilities except in the vicinity of the cone meridian where a roughness element was placed midway along the length of the cone. The growth of first mode instabilities is found to be weak at all trajectory points analyzed from the ascent phase. For times less than approximately 18.5 seconds into the flight, the peak amplification ratio for second mode disturbances is sufficiently small because of the lower Mach numbers at earlier times, so that the transition behavior inferred from the measurements is attributed to an unknown physical mechanism, potentially related to step discontinuities in surface height near the locations of a change in the surface material. Based on the time histories of temperature and/or heat flux at transducer locations within the aft portion of the cone, the onset of transition correlated with a linear N-factor, based on parabolized stability equations, of approximately 13.5. Due to the large angles of attack during the re-entry phase, crossflow instability may play a significant role in transition. Computations also indicate the presence of pronounced crossflow separation over a significant portion of the trajectory segment that is relevant to transition analysis. The transition behavior during this re-entry segment of HIFiRE-1 flight shares some common features with the predicted transition front along the elliptic cone shaped HIFiRE-5 flight article, which was designed to provide hypersonic transition data for a fully 3D geometric configuration. To compare and contrast the

Framework for ReSTful Web Services in OSGi

Science.gov (United States)

Shams, Khawaja S.; Norris, Jeffrey S.; Powell, Mark W.; Crockett, Thomas M.; Mittman, David S.; Fox, Jason M.; Joswig, Joseph C.; Wallick, Michael N.; Torres, Recaredo J.; Rabe, Kenneth

2009-01-01

Ensemble ReST is a software system that eases the development, deployment, and maintenance of server-side application programs to perform functions that would otherwise be performed by client software. Ensemble ReST takes advantage of the proven disciplines of ReST (Representational State Transfer. ReST leverages the standardized HTTP protocol to enable developers to offer services to a diverse variety of clients: from shell scripts to sophisticated Java application suites

Analysis of heavy alloying elements segregation in gravity cast experimental Mg-Al-Zn-RE alloy

Directory of Open Access Journals (Sweden)

A. Żydek

2010-01-01

Full Text Available Microstructure of experimental AZ91 alloy with an addition of rare earth elements (RE at a level of 4 wt.% was examined by means of light microscopy. The investigated AZ91 + 4 wt.% RE alloy was fabricated by adding cerium rich mish metal to molten commercial AZ91 alloy. In the microstructure of the resulting alloy, besides α solid solution, α + γ eutectic and discontinuous precipitates of γ phase, also the Al11RE3 phase with needle-like morphology and the polygonal Al10RE2Mn7 phase were revealed. No segregation of rare earth elements was found in the investigated gravity cast alloy, which was confirmed by statistical analysis of cerium concentrations in selected parts of the cast. Similar results were obtained for manganese. Ce and Mn concentrations were determined by a spectrophotometric method.

Unraveling the Raman Enhancement Mechanism on 1T'-Phase ReS2 Nanosheets.

Science.gov (United States)

Miao, Peng; Qin, Jing-Kai; Shen, Yunfeng; Su, Huimin; Dai, Junfeng; Song, Bo; Du, Yunchen; Sun, Mengtao; Zhang, Wei; Wang, Hsing-Lin; Xu, Cheng-Yan; Xu, Ping

2018-04-01

2D transition metal dichalcogenides materials are explored as potential surface-enhanced Raman spectroscopy substrates. Herein, a systematic study of the Raman enhancement mechanism on distorted 1T (1T') rhenium disulfide (ReS 2 ) nanosheets is demonstrated. Combined Raman and photoluminescence studies with the introduction of an Al 2 O 3 dielectric layer unambiguously reveal that Raman enhancement on ReS 2 materials is from a charge transfer process rather than from an energy transfer process, and Raman enhancement is inversely proportional while the photoluminescence quenching effect is proportional to the layer number (thickness) of ReS 2 nanosheets. On monolayer ReS 2 film, a strong resonance-enhanced Raman scattering effect dependent on the laser excitation energy is detected, and a detection limit as low as 10 -9 m can be reached from the studied dye molecules such as rhodamine 6G and methylene blue. Such a high enhancement factor achieved through enhanced charge interaction between target molecule and substrate suggests that with careful consideration of the layer-number-dependent feature and excitation-energy-related resonance effect, ReS 2 is a promising Raman enhancement platform for sensing applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of mixing RE elements (Nd, Sm, Gd, Eu, Y, Yb) on the RE2BaCuO5/Nd4-2xBa2+2xCu2-xO10-2x phases in RE cuprate high-Tc superconductors

International Nuclear Information System (INIS)

Langhorn, J.B.; Black, M.A.; McGinn, P.J.

1999-01-01

The phases RE 2 BaCuO 5 /RE 4 Ba 2 Cu 2 O 10 phases (where RE is a mixture of Nd, Sm, Gd, Eu, Y and Yb) have been synthesized in an oxygen atmosphere and subsequently characterized. The mixing of RE elements which inherently form the RE 2 BaCuO 5 phase through the peritectic decomposition of REBa 2 Cu 3 O 7-x (RE123) (i.e. Sm, Gd, Eu, Y, Yb), was observed to give homogeneous mixing of the elements in the 211 phase. In contrast it was found that on mixing Nd with other RE elements a mixture of the Nd 4-2x Ba 2+2x Cu 2-x O 10-2x (Nd422) and RE 2 BaCuO 5 (RE211) phases resulted. It was also observed that on mixing Nd with other REs a finite amount of the RE is substituted into the Nd422 phase and Nd into the RE211. (author)

Diagnostic criteria for Menière's disease.

Science.gov (United States)

Lopez-Escamez, Jose A; Carey, John; Chung, Won-Ho; Goebel, Joel A; Magnusson, Måns; Mandalà, Marco; Newman-Toker, David E; Strupp, Michael; Suzuki, Mamoru; Trabalzini, Franco; Bisdorff, Alexandre

2015-01-01

This paper presents diagnostic criteria for Menière's disease jointly formulated by the Classification Committee of the Bárány Society, The Japan Society for Equilibrium Research, the European Academy of Otology and Neurotology (EAONO), the Equilibrium Committee of the American Academy of Otolaryngology-Head and Neck Surgery (AAO-HNS) and the Korean Balance Society. The classification includes two categories: definite Menière's disease and probable Menière's disease. The diagnosis of definite Menière's disease is based on clinical criteria and requires the observation of an episodic vertigo syndrome associated with low- to medium-frequency sensorineural hearing loss and fluctuating aural symptoms (hearing, tinnitus and/or fullness) in the affected ear. Duration of vertigo episodes is limited to a period between 20 minutes and 12 hours. Probable Menière's disease is a broader concept defined by episodic vestibular symptoms (vertigo or dizziness) associated with fluctuating aural symptoms occurring in a period from 20 minutes to 24 hours.

Ternary rare-earth bismuthides RE5SiBi 2 and RE5GeBi 2 ( RE=La-Nd, Gd-Er): Stabilization of the β-Yb 5Sb 3-type structure through tetrel substitution

Science.gov (United States)

Barry, Stephen D.; Tkachuk, Andriy V.; Bie, Haiying; Blanchard, Peter E. R.; Mar, Arthur

2011-01-01

Ternary bismuthides RE5TtBi 2 containing rare-earth ( RE=La-Nd, Gd-Er) and tetrel ( Tt=Si, Ge) atoms have been prepared by arc-melting of the elements followed by annealing at 800 °C. They adopt the β-Yb 5Sb 3-type structure (Pearson symbol o P32, space group Pnma, Z=4), as revealed through analysis by single-crystal X-ray diffraction on Ce 5Si 0.869(4)Bi 2.131(4) and powder X-ray diffraction on Ce 5GeBi 2. Cell parameters for the entire series lie in the ranges of a=12.8-11.8 Å, b=9.6-9.0 Å, and c=8.4-7.9 Å. Solid solubility in Ce 5Si xBi 3- x and Pr 5Si xBi 3- x (approximately 0.9≤ x≤1.2, depending on the RE member) is much more limited compared to the antimonides, consistent with a highly ordered structure in which the two possible anion sites are essentially segregated into a smaller one occupied by Tt atoms (CN7) and a larger one occupied by Bi atoms (CN9). Band structure calculations on La 5SiBi 2 confirm the importance of La-La bonding interactions near the Fermi level. X-ray photoelectron spectra support the presence of partially anionic Bi atoms, as indicated by a small negative binding energy shift relative to elemental Bi. The Ce and Pr members undergo magnetic transitions at low temperatures, possibly involving ferromagnetic interactions, that are strongly influenced by the nature of the Tt atom.

Giant magnetostriction in Ca2FeReO6 double perovskite

International Nuclear Information System (INIS)

Serrate, D.; De Teresa, J.M.; Algarabel, P.A.; Marquina, C.; Morellon, L.; Blasco, J.; Ibarra, M.R.

2005-01-01

We report magnetostriction measurements in polycrystalline Ca 2 FeReO 6 magnetic double perovskite up to 20T and in the temperature range 4.2-250K. This compound shows a high Curie temperature (T C =523K) and a structural transition at low temperatures (T S =110K). By combining magnetostriction measurements parallel and perpendicular to the magnetic field, we evaluate the anisotropic (λ t ) and volume magnetostriction (ω). The λ t at room temperature is large and reaches below T S the giant value of ∼0.1% at 15T. Below T S , the ω is also found to be large: ∼0.05% at 15T at 5K. These results are interpreted within a scenario where the Re orbital state plays a crucial role in the ground state. The observed effect could open a new way to observe giant magnetostriction effects in transition-metal-based magnetic oxides through suitable tuning of the orbital effects in the transition metals

2.2.1. Synthesis, spectroscopic characterization and crystal structure of [ReV(O2(pyz4][ReII(NOBr4(pyz] (pyz = pyrazine

Directory of Open Access Journals (Sweden)

Mario Pacheco, Alicia Cuevas, Javier González-Platas, Carlos Kremer*

2015-03-01

Full Text Available Abstract: A novel Re(V-Re(II nitrosyl complex, [Re(O2(pyz 4][Re(NOBr4(pyz] (pyz = pyrazine was prepared and characterized by X-ray diffraction, elemental analysis, infrared and ultraviolet-visible absorption spectra. This product is obtained in the initial steps of the reaction of (NBu4[Re(NOBr4(EtOH] with pyrazine. Both, the cation and the anion are mononuclear complexes. The Re(V atom in the cation is six-coordinate with four nitrogen atoms from pyrazine ligands, and two oxo ligands. The Re(II anion is also six-coordinate, with four bromide ligands, a linear nitrosyl group and one nitrogen from pyrazine. The spectroscopic studies are discussed and compared with those already reported separately for the cation and the anion. Supporting information: X-Ray (CIF file

Small Commercial Building Re-tuning: A Primer

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Hostick, Donna J.; Underhill, Ronald M.; Fernandez, Nicholas; Katipamula, Srinivas

2013-09-30

To help building owners and managers address issues related to energy-efficient operation of small buildings, DOE has developed a Small Building Re-tuning training curriculum. This "primer" provides additional background information to understand some of the concepts presented in the Small Building Re-tuning training. The intent is that those who are less familiar with the buidling energy concepts will review this material before taking the building re-tuning training class.

Hierarchical architecture of ReS_2/rGO composites with enhanced electrochemical properties for lithium-ion batteries

International Nuclear Information System (INIS)

Qi, Fei; Chen, Yuanfu; Zheng, Binjie; He, Jiarui; Li, Qian; Wang, Xinqiang; Lin, Jie; Zhou, Jinhao; Yu, Bo; Li, Pingjian; Zhang, Wanli

2017-01-01

Highlights: • The ReS_2/rGO composites have been synthesized by a facile one-pot method. • The ReS_2/rGO composites exhibit hierarchical architecture. • The ReS_2/rGO composites deliver better electrochemical performances than ReS_2. • The enhanced performance is due to porous and conductive structure of ReS_2/rGO. - Abstract: Rhenium disulfide (ReS_2), a two-dimensional (2D) semiconductor, has attracted more and more attention due to its unique anisotropic electronic, optical, mechanical properties. However, the facile synthesis and electrochemical property of ReS_2 and its composite are still necessary to be researched. In this study, for the first time, the ReS_2/reduced graphene oxide (rGO) composites have been synthesized through a facile and one-pot hydrothermal method. The ReS_2/rGO composites exhibit a hierarchical, interconnected, and porous architecture constructed by nanosheets. As anode for lithium-ion batteries, the as-synthesized ReS_2/rGO composites deliver a large initial capacity of 918 mAh g"−"1 at 0.2 C. In addition, the ReS_2/rGO composites exhibit much better electrochemical cycling stability and rate capability than that of bare ReS_2. The significant enhancement in electrochemical property can be attributed to its unique architecture constructed by nanosheets and porous structure, which can allow for easy electrolyte infiltration, efficient electron transfer, and ionic diffusion. Furthermore, the graphene with high electronic conductivity can provide good conductive passageways. The facile synthesis approach can be extended to prepare other 2D transition metal dichalcogenides semiconductors for energy storage and catalytic application.

Photoluminescence properties of aeschynite-type LaNbTiO6:RE3+ (RE = Tb, Dy, Ho) down-converting phosphors.

Science.gov (United States)

Ma, Qian; Lu, Mengkai; Yang, Ping; Zhang, Aiyu; Cao, Yongqiang

2014-06-01

In this study, a series of LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) down-converting phosphors were synthesized using a modified sol-gel combustion method, and their photoluminescence (PL) properties were investigated as a function of activator concentration and annealing temperature. The resultant particles were characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, UV/Vis diffuse reflectance spectroscopy and PL spectra. The highly crystalline LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) phosphors with an average size of 200-300 nm obtained at 1100°C have an orthorhombic aeschynite-type structure and exhibit the highest luminescent intensity in our study range. The emission spectra of LaNbTiO6:RE(3+) (RE = Tb, Dy, Ho) phosphors under excitations at UV/blue sources are mainly composed of characteristic peaks arising from the f-f transitions of RE(3+), including 489 nm ((5) D4 → (7) F6) and 545 nm ((5) D4 → (7) F5) for Tb(3+), 476 and 482 nm ((4) F9/2 → (6) H15/2) and 571 nm ((4) F9/2 → (6) H13/2) for Dy(3+), and 545 nm ((5) F4 + (5) S2 → (5) I8) for Ho(3+), respectively. The luminescent mechanisms were further investigated. It can be expected that these phosphors are of intense interest and potential importance for many optical applications. Copyright © 2013 John Wiley & Sons, Ltd.

188W→188Re generator for biomedical applications

International Nuclear Information System (INIS)

Kamioki, Hiroshi; Mirzadeh, S.; Lambrecht, R.M.; Knapp, R. Jr.; Dadachova, K.

1994-01-01

An alumina-based 188 W → 188 Re generator was evaluated for 188 Re yield and elution profile and 188 W breakthrough using various reagents for a three-month period. To address the problem of low specific volume, the generator was eluted with reagents which could be easily destroyed by gentle evaporation from acidic solutions (e.g. NH 4 Cl and NH 4 NO 3 ). We also evaluated a proposed ''alumina/anion-exchange'' tandem generator for the preparation of highly purified 188 Re as perrhenic acid. In parallel studies, the adsorption dynamics of tungsten on alumina showed a sharp rise in the tungsten breakthrough at W/Al 2 O 3 ratio of ∼ 120 mg/g corresponding to a distribution constant of ∼ 8400 from nitrate solution at 0.05 M ionic strength. In adsorption on anion exchange resins, carrier-free 188 Re exhibited a behavior very similar to that of macroscopic quantities of Re. These studies further demonstrated the long and useful shelf-life of 188 W → 188 Re generator. (orig.)

Jacques Rancière and indisciplinarity

NARCIS (Netherlands)

Baronian, M.A.; Rosello, M.

2008-01-01

This is the transcript of an interview conducted with Jacques Rancière by Marie-Aude Baronian and Mireille Rosello from the University of Amsterdam and ASCA. A version of this interview was published in Dutch by Valiz (NL), in a volume of studies on Jacques Rancière that appeared in the Netherlands

Absolute counting of 188Re radiopharmaceuticals

International Nuclear Information System (INIS)

Ravindra, Anuradha; Kulkarni, D.B.; Joseph, Leena; Kulkarni, M.S.

2018-01-01

Rhenium-188 is radiopharmaceutical that belongs to the group of strong beta-weak gamma emitters. It emits high energy beta particles, (E β m ax = 2.12MeV) and weak gamma rays (E γ = 155 keV) hence makes it suitable for wide variety of therapeutic as well as diagnostic applications. Therapeutic applications include therapy of tumors, radionuclide synovectomy, bone pain palliation, intra vascular radiation therapy etc. 188 Re-labeled medicines have been employed increasingly in the therapy of tumors and vascular restenosis. To ensure that patient receives the appropriate radiation dose during the treatment, both the activity standardization and the determination of sensitivity coefficient of the secondary standard for 188 Re have become important tasks. This paper presents the methods and results obtained for the following measurements a) Standardisation of the 188 Re by using the 4π proportional counter (4πPC)-gamma extrapolation method b) Determination of sensitivity coefficient (pA/MBq) of the secondary standard ionization chamber type Centronic IG12, 20A for 188 Re

75 FR 23631 - Sugar Re-Export Program, the Sugar-Containing Products Re-Export Program, and the Polyhydric...

Science.gov (United States)

2010-05-04

... Part 1530 Sugar Re-Export Program, the Sugar-Containing Products Re-Export Program, and the Polyhydric...), Additional U.S. Note 6, which authorizes entry of raw cane sugar under subheading 1701.11.20 of the HTS for the production of polyhydric alcohols, except polyhydric alcohols for use as a substitute for sugar in...

Re-assessment of dose from the Vinten extremity dosemeter

International Nuclear Information System (INIS)

O'Hagan, J.B.; Pearson, A.J.; Dutt, J.C.

1989-01-01

A procedure is described for re-assessing the dose from the Vinten extremity dosemeter using phototransferred thermoluminescence. The technique produces a linear response up to 50 Sv. The re-assessment efficiency is approximately 10% for the first re-assessment and 3-5% for the second re-assessment. The detection threshold values (at the 95% confidence level) are 3 mSv and 9 mSv respectively. (author)

[ReF₆]^2-

DEFF Research Database (Denmark)

Pedersen, Kasper Steen; Sigrist, Marc; Sørensen, Mikkel Agerbæk

2014-01-01

studied including the slow relaxation of the magnetization observed below ca. 4 K. This slow dynamic is preserved for the one-dimensional coordination polymer [Zn(viz)4(ReF 6)]1 (2, viz=1-vinylimidazole), demonstrating the irrelevance of low symmetry for such magnetization dynamics in systems with easy......-plane-type anisotropy. The ability of fluoride to mediate significant exchange interactions is exemplified by the isostructural [Ni(viz)4(ReF6)]1 (3) analogue in which the ferromagnetic NiII-ReIV interaction (+10.8 cm-1) dwarfs the coupling present in related cyanide-bridged systems. These results reveal [ReF6...

ASR and RE

DEFF Research Database (Denmark)

Jensen, Tim

2016-01-01

As a university discipline, the academic study of religions (ASR) has produced a critical approach to the study of religion which is (or ought be), I think, of fundamental importance for a modern secular and enlightened democratic state. However, the ”study-of-religions” approach has percolated...... with limited success into society at large as well as into the primary and secondary educational systems of Western democracies. Too often so-called religious education (RE) really is religious or confessional, and even so-called non-confessional RE is, mostly if not always, mixed with crypto......-confessional approaches, inculcation of moral values (not least those claimed to be Christian) and the promoting of religion as a resource for a more ”spiritual” approach to life. While these goals may be in line with the traditional use of the public school as the key instrument of the (nation-) state to try to confer...

Nano-Ionic Solid State Resistive Memories (Re-RAM): A Review.

Science.gov (United States)

Sahoo, Satyajeet; Prabaharan, S R S

2017-01-01

Nano-ionic devices based on modest to fast ion conductors as active materials intrigued a revolution in the field of nano solid state resistive memories (the so-called Re-RAM) ever since HP labs unveiled the first solid state memristor device based on titanium dioxide (TiO2). This has brought impetus to the practical implementation of fourth missing element called “Memristor” correlating charge (q) and flux (φ) based on the conceptual thought by Chua in 1971 completing a missing gap between the passive electronic components (R, C and L). It depicts various functional features as memory element in terms of ionic charge transport in solid state by virtue of external electric flux variations. Consequently, a new avenue has been found by manipulating the ionic charge carriers creating a fast switching resistive random access memory (Re-RAM) or the so-called Memristors. The recent research has led to low power, faster switching speed, high endurance and high retention time devices that can be scaled down the order of few nanometers dimension and the 3D stacking is employed that significantly reduces the die area. This review is organized to provide the progress hitherto accomplished in the materials arena to make memristor devices with respect to current research attempts, different stack structures of ReRAM cells using various materials as well as the application of memristive system. Different synthesis approaches to make nano-ionic conducting metal oxides, the fabrication methods for ReRAM cells and its memory performance are reviewed comprehensively.

Phase characterization of Re-based diffusion barrier layer on Nb substrate

International Nuclear Information System (INIS)

Sugiarti, Eni; Wang, Youngmin; Hashimoto, Naoyuki; Ohnuki, Somei; Narita, Toshio

2011-01-01

An electron microscopy phase characterization was carried out for a Re-based diffusion barrier layer, which was deposited on the Nb substrate used as an ultra high temperature material. The coating process produced three layers; an outer Cr(Re) layer, an intermediate Cr-Nb-Re layer, and an inner Nb(Re) layer. The Cr-Nb-Re layer is considered to act as a diffusion barrier layer between the substrate and the outer Cr(Re) reservoir layer. The Cr(Re) and Nb(Re) layers are in single phase with a similar bcc structures, but they are different in structure from the intermediate layer, which is composed of a dual phase of Re 63 Cr 20 Nb 17 with a cubic structure and Nb 42 Re 33 Cr 25 with a hexagonal structure determined by transmission electron microscopy (TEM) in this study. (author)

At være optimal

DEFF Research Database (Denmark)

Holm, Karina Ellegaard; Frederiksen, Kirsten Søndergaard; Kolind, Torsten

2016-01-01

Kapitlet undersøger forholdet til fest og rus blandt unge med anden etnisk baggrund end dansk. Det er tydeligt, at alkohol, fester, rus og kropslighed opleves forskelligt blandt de interviewede; for nogle handler fest om mad, dans, musik og at gøre sig lækker, mens det for andre også handler om r...... sammen med fulde klassekammerater. Selv de få, som beretter om rusmiddelbrug, fortæller, at det foregår med målet om at være optimal....

Mechanical properties and electronic structure of anti-ReO3 structured cubic nitrides, M3N, of d block transition metals M: An ab initio study

International Nuclear Information System (INIS)

Zhou, Xiuquan; Gall, Daniel; Khare, Sanjay V.

2014-01-01

Highlights: • We use DFT to model the anti-ReO 3 structured transition metal nitrides M 3 N. • We predict their lattice constants, electronic structures and mechanical properties. • We correlate the metal d and nitrogen 2p orbitals with stability and hardness. • We established a high-throughput database for materials design. - Abstract: We report a systematic study of the anti-ReO 3 structured transition metal nitrides, M 3 N, using ab initio density functional theory computations in the local density approximation. Here M denotes all the 3d, 4d and 5d transition metals. Our calculations indicate that all M 3 N compounds except V 3 N of group 5 and Zn 3 N and Hg 3 N of group 12 are mechanically stable. For the stable M 3 N compounds, we report a database of predictions for their lattice constants, electronic properties and mechanical properties including bulk modulus, Young’s modulus, shear modulus, ductility, hardness and Debye temperature. It is found that most M 3 N compounds exhibit ductility with Vickers hardness between 0.4 GPa and 11.2 GPa. Our computed lattice constant for Cu 3 N, the only M 3 N compound where experiments exist, agrees well with the experimentally reported values. We report ratios of the melting points of all M 3 N compounds to that of Cu 3 N. The local density of states for all M 3 N compounds are obtained, and electronic band gaps are observed only for M of group 11 (Cu, Ag and Au) while the remaining M 3 N compounds are metallic without band gaps. Valence electron density along with the hybridization of the metal d and nitrogen 2p orbitals play an important role in determining the stability and hardness of different compounds. Our high-throughput databases for the cubic anti-ReO 3 structured transition metal nitrides should motivate future experimental work and shorten the time to their discovery

Re-Sonification of Objects, Events, and Environments

Science.gov (United States)

Fink, Alex M.

Digital sound synthesis allows the creation of a great variety of sounds. Focusing on interesting or ecologically valid sounds for music, simulation, aesthetics, or other purposes limits the otherwise vast digital audio palette. Tools for creating such sounds vary from arbitrary methods of altering recordings to precise simulations of vibrating objects. In this work, methods of sound synthesis by re-sonification are considered. Re-sonification, herein, refers to the general process of analyzing, possibly transforming, and resynthesizing or reusing recorded sounds in meaningful ways, to convey information. Applied to soundscapes, re-sonification is presented as a means of conveying activity within an environment. Applied to the sounds of objects, this work examines modeling the perception of objects as well as their physical properties and the ability to simulate interactive events with such objects. To create soundscapes to re-sonify geographic environments, a method of automated soundscape design is presented. Using recorded sounds that are classified based on acoustic, social, semantic, and geographic information, this method produces stochastically generated soundscapes to re-sonify selected geographic areas. Drawing on prior knowledge, local sounds and those deemed similar comprise a locale's soundscape. In the context of re-sonifying events, this work examines processes for modeling and estimating the excitations of sounding objects. These include plucking, striking, rubbing, and any interaction that imparts energy into a system, affecting the resultant sound. A method of estimating a linear system's input, constrained to a signal-subspace, is presented and applied toward improving the estimation of percussive excitations for re-sonification. To work toward robust recording-based modeling and re-sonification of objects, new implementations of banded waveguide (BWG) models are proposed for object modeling and sound synthesis. Previous implementations of BWGs

STS-134 Re-Rendezvous Design History

Science.gov (United States)

Stuit, Timothy D.

2011-01-01

In preparation to provide the capability for the Orion spacecraft to rendezvous with the International Space Station (ISS), a new suite of relative navigation sensors are in development and will be tested on one of the final Space Shuttle missions to ISS. The National Aeronautics and Space Administration (NASA) commissioned a flight test of prototypes of the instruments on STS-134, in order to test their performance in the space environment during the nominal rendezvous and docking, as well as a re-rendezvous dedicated to testing the prototype sensors following the undocking of the Space Shuttle Orbiter at the end of the mission. Unlike the initial rendezvous and docking, the re-rendezvous profile would replicate the newly designed Orion coelliptic approach trajectory, something never before attempted with the Shuttle Orbiter. Therefore, there were a number of new parameters that needed to be conceived of, designed, and tested for this re-rendezvous to make the flight test successful. And all of this work had to be integrated with the normal operations of the ISS and Shuttle and had to conform to the constraints of the mission and vehicles. The result of this work is a separation and re-rendezvous trajectory design that will prove not only the design of the relative navigation sensors for the Orion vehicle, but also will serve as a proof of concept for the Orion rendezvous trajectory itself. This document presents the analysis and decision making process involved in attaining the final STS-134 re-rendezvous design.

Study on the preparation and stability of 188Re biomolecules via EHDP

International Nuclear Information System (INIS)

Ferro-Flores, G.; Garcia-Salinas, L.; Paredes-Gutierrez, L.; Hashimoto, K.; Melendez-Alafort, L.; Murphy, C.A.

2001-01-01

A direct labelling technique via ethane-1-hydroxy-1,1-diphosphonic acid (EHDP) as a weak competing ligand was developed for the preparation of several biomolecules: 188 Re-monoclonal antibody ior cea1 against carcinoembryonic antigen ( 188 Re-MoAb), biotinylated 188 Re-MoAb ( 188 Re-MoAb-biotin), 188 Re-polyclonal IgG ( 188 Re-IgG), 188 Re-peptide (somatostatine analogue peptide b-(2-naphtyl)-D-Ala-Cys-Tyr-D-Trp-Lys-Val-Cys-Thr-amide), 188 Re-MoAb fragments ( 188 Re-F(ab') 2 ) and biotinylated 188 Re-F(ab') 2 ( 188 Re-F(ab') 2 -biotin). The reaction conditions such as pH, temperature, weak ligand concentration and stannous chloride concentration were optimized during the radiolabelling of each biomolecule. Before the labelling procedure, disulphide bridge groups of the biomolecules were reduced with 2-mercaptoethanol (2-ME). To obtain 188 Re labelled antibodies and peptides in high radiochemical yields (>90%) via EHDP, it was necessary to use acidic conditions and a high concentration of stannous chloride to allow the redox reaction Re +7 →Re +5 :Re +4 . The labelling of MoAb and F(ab') 2 with 188 Re via EHDP was also evaluated employing a pretargeted technique by avidin-biotin strategy in normal mice, demonstrating that the 188 Re-labelled biotinylated antibodies are stable complexes in vivo. The 188 Re-peptide complex prepared by this method, was stable for 24 h and no radiolytic degradation was observed. (author)

Beneficial Re-use of Decommissioned Former Nuclear Facilities

International Nuclear Information System (INIS)

Boing, L.E.

1997-01-01

With the decision to decommission a nuclear facility, it is necessary to evaluate whether to fully demolish a facility or to re-use the facility in some capacity. This evaluation is often primarily driven by both the past mission of the site and the facility and the site's perceived future mission. In the case where the facility to be decommissioned is located within a large research or industrial complex and represents a significant resource to the site's future mission, it may be a perfect candidate to be re-used in some fashion. However, if the site is a rather remote older facility with little chance of being modified to today's standards for its re-use, the chances for its re-use will be substantially reduced. In this presentation, some specific cases of former nuclear facilities being decommissioned and re-used will be reviewed and some factors required to be considered in making this decision will be reviewed

Defense programs business practices re-engineering QFD exercise

International Nuclear Information System (INIS)

Murray, C.; Halbleib, L.

1996-03-01

The end of the cold war has resulted in many changes for the Nuclear Weapons Complex (NWC). We now work in a smaller complex, with reduced resources, a smaller stockpile, and no new phase 3 weapons development programs. This new environment demands that we re-evaluate the way we design and produce nuclear weapons. The Defense Program (DP) Business Practices Re-engineering activity was initiated to improve the design and production efficiency of the DP Sector. The activity had six goals: (1) to identify DP business practices that are exercised by the Product Realization Process (PRP); (2) to determine the impact (positive, negative, or none) of these practices on defined, prioritized customer criteria; (3) to identify business practices that are candidates for elimination or re-engineering; (4) to select two or three business practices for re-engineering; (5) to re-engineer the selected business practices; and (6) to exercise the re-engineered practices on three pilot development projects. Business practices include technical and well as administrative procedures that are exercised by the PRP. A QFD exercise was performed to address (1)-(4). The customer that identified, defined, and prioritized the criteria to rate the business practices was the Block Change Advisory Group. Five criteria were identified: cycle time, flexibility, cost, product performance/quality, and best practices. Forty-nine business practices were identified and rated per the criteria. From this analysis, the group made preliminary recommendations as to which practices would be addressed in the re-engineering activity. Sixteen practices will be addressed in the re-engineering activity. These practices will then be piloted on three projects: (1) the Electronic Component Assembly (ECA)/Radar Project, (2) the B61 Mod 11, and (3) Warhead Protection Program (WPP)

The availability of plutonium and americium in Irish Sea sediments for re-dissolution

International Nuclear Information System (INIS)

McDonald, P.; Vives i Batlle, J.; Bousher, A.; Whittall, A.; Chambers, N.

2001-01-01

The availability of plutonium and americium, for re-dissolution from offshore sediments into Irish Sea water, has been examined. Sediments collected from the mud-patch near the Cumbrian coast were characterized in terms of spatial location, particle size, partitioning of radionuclides with respect to physico-chemical bonds and availability of actinides for release into seawater. Sequential extraction investigations revealed that plutonium was predominantly associated with strongly bound sesquioxide and organic complex fractions. Americium was associated mainly with the organic complex fraction, but a significant fraction was in carbonate form. Sediment/water re-dissolution experiments with and without stirring were compared to simulate the effect of disturbing bed sediment. After 1 week, neither set of re-dissolution data provided significant trends between dissolved activity and time. Stirred systems appeared to release 2.5 times more plutonium and americium into seawater than unstirred systems. Measured 239,240Pu and 241Am distribution coefficients (K d values) were both typically approximately 10 5 l kg -1 . 241Am K d values are an order of magnitude lower than previously reported for the north-eastern Irish Sea, but similar to western Irish Sea values. Overall, the fractions of plutonium and americium available for re-dissolution from bed sediment are very low at <0.1%, with proportionally more plutonium being released than americium. These findings lend further support for the extrapolation of laboratory-derived information to environmental conditions

Development of pharmaceuticals with radioactive rhenium for cancer therapy. Production of {sup 186}Re and {sup 188}Re, synthesis of labeled compounds and their biodistributions

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Production of the radioactive rhenium isotopes {sup 186}Re and {sup 188}Re, and synthesis of their labeled compounds have been studied together with the biodistributions of the compounds. This work was carried out by the Working Group on Radioactive Rhenium, consisting of researchers of JAERI and some universities, in the Subcommittee for Production and Radiolabeling under the Consultative Committee of Research on Radioisotopes. For {sup 186}Re, production methods by the {sup 185}Re(n,{gamma}){sup 186}Re reaction in a reactor and by the {sup 186}W(p,n){sup 186}Re reaction with an accelerator, which can produce nocarrier-added {sup 186}Re, have been established. For {sup 188}Re, a production method by the double neutron capture reaction of {sup 186}W, which produces a {sup 188}W/{sup 188}Re generator, has been established. For labeling of bisphosphonate, DMSA, DTPA, DADS, aminomethylenephosphonate and some monoclonal antibodies with the radioactive rhenium isotopes, the optimum conditions, including pH, the amounts of reagents and so on, have been determined for each compound. The biodistributions of each of the labeled compounds in mice have been also obtained. (author)

Image re-sampling detection through a novel interpolation kernel.

Science.gov (United States)

Hilal, Alaa

2018-06-01

Image re-sampling involved in re-size and rotation transformations is an essential element block in a typical digital image alteration. Fortunately, traces left from such processes are detectable, proving that the image has gone a re-sampling transformation. Within this context, we present in this paper two original contributions. First, we propose a new re-sampling interpolation kernel. It depends on five independent parameters that controls its amplitude, angular frequency, standard deviation, and duration. Then, we demonstrate its capacity to imitate the same behavior of the most frequent interpolation kernels used in digital image re-sampling applications. Secondly, the proposed model is used to characterize and detect the correlation coefficients involved in re-sampling transformations. The involved process includes a minimization of an error function using the gradient method. The proposed method is assessed over a large database of 11,000 re-sampled images. Additionally, it is implemented within an algorithm in order to assess images that had undergone complex transformations. Obtained results demonstrate better performance and reduced processing time when compared to a reference method validating the suitability of the proposed approaches. Copyright © 2018 Elsevier B.V. All rights reserved.

Efficient Conditional Proxy Re-encryption with Chosen-Ciphertext Security

NARCIS (Netherlands)

Weng, Jiang; Yang, Yanjiang; Tang, Qiang; Deng, Robert H.; Bao, Feng

Recently, a variant of proxy re-encryption, named conditional proxy re-encryption (C-PRE), has been introduced. Compared with traditional proxy re-encryption, C-PRE enables the delegator to implement fine-grained delegation of decryption rights, and thus is more useful in many applications. In this

'If they're helping me then how can I be independent?' The perceptions and experience of users of home-care re-ablement services.

Science.gov (United States)

Wilde, Alison; Glendinning, Caroline

2012-11-01

Home-care re-ablement is a short-term, intensive service that helps people to (re-) establish their capacity and confidence in performing basic personal care and domestic tasks at home, thereby reducing needs for longer term help. Home-care re-ablement is an increasingly common feature of English adult social care services; there are similar service developments in Australia and New Zealand. This paper presents evidence from semi-structured interviews conducted in early 2010 with 34 service users and 10 carers from five established re-ablement services in England. The interviews formed part of a larger, mixed-methods study into the immediate and longer term impacts and cost-effectiveness of home-care re-ablement services. There was clear evidence that interviewees felt that they had benefitted from re-ablement services; most service users and their families valued the intervention. However, the interviews also identified potential barriers to optimal independence for some service users, particularly those with progressive conditions, sensory impairments, specific cultural needs, or who lived alone. The beneficial impacts of re-ablement could also be reduced if users failed to understand the aims of the service, or if the service failed to provide support with activities or outcomes that were particularly important to the service user or carer. Putting the lived experiences of people receiving re-ablement at the centre of analysis, this paper concludes that re-ablement services have the potential for enhanced effectiveness, particularly if there is more understanding of users' own priorities and concepts of independence. © 2012 Blackwell Publishing Ltd.

a comparison of bond perform with reinforcements from son of bond ...

African Journals Online (AJOL)

User

steel that are manufactured from metal scraps (re- ... metal scraps from re-cycle obsolete vehicle and machine ..... (PAC) Reinforced With Glass-Fibre-Reinforced. Polymer ... 99 – 113. [8] Abrishami H. H. and Mitchell D. (1992) “Simulation of.

Hierarchical architecture of ReS{sub 2}/rGO composites with enhanced electrochemical properties for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Qi, Fei; Chen, Yuanfu, E-mail: yfchen@uestc.edu.cn; Zheng, Binjie; He, Jiarui; Li, Qian; Wang, Xinqiang; Lin, Jie; Zhou, Jinhao; Yu, Bo; Li, Pingjian; Zhang, Wanli

2017-08-15

Highlights: • The ReS{sub 2}/rGO composites have been synthesized by a facile one-pot method. • The ReS{sub 2}/rGO composites exhibit hierarchical architecture. • The ReS{sub 2}/rGO composites deliver better electrochemical performances than ReS{sub 2}. • The enhanced performance is due to porous and conductive structure of ReS{sub 2}/rGO. - Abstract: Rhenium disulfide (ReS{sub 2}), a two-dimensional (2D) semiconductor, has attracted more and more attention due to its unique anisotropic electronic, optical, mechanical properties. However, the facile synthesis and electrochemical property of ReS{sub 2} and its composite are still necessary to be researched. In this study, for the first time, the ReS{sub 2}/reduced graphene oxide (rGO) composites have been synthesized through a facile and one-pot hydrothermal method. The ReS{sub 2}/rGO composites exhibit a hierarchical, interconnected, and porous architecture constructed by nanosheets. As anode for lithium-ion batteries, the as-synthesized ReS{sub 2}/rGO composites deliver a large initial capacity of 918 mAh g{sup −1} at 0.2 C. In addition, the ReS{sub 2}/rGO composites exhibit much better electrochemical cycling stability and rate capability than that of bare ReS{sub 2}. The significant enhancement in electrochemical property can be attributed to its unique architecture constructed by nanosheets and porous structure, which can allow for easy electrolyte infiltration, efficient electron transfer, and ionic diffusion. Furthermore, the graphene with high electronic conductivity can provide good conductive passageways. The facile synthesis approach can be extended to prepare other 2D transition metal dichalcogenides semiconductors for energy storage and catalytic application.

A single crystal study of RE{sub 14}Co{sub 3}In{sub 3} (RE = Y, Tb, Dy, Ho, Er)

Energy Technology Data Exchange (ETDEWEB)

Zaremba, V.I.; Kalychak, Y.M.; Dzevenko, M.V. [Inorganic Chemistry Dept., Ivan Franko National Univ. of Lviv (Ukraine); Rodewald, U.Ch.; Heying, B.; Poettgen, R. [Inst. fuer Anorganische und Analytische Chemie, Westfaelische Wilhelms-Univ. Muenster (Germany)

2006-01-01

The rare earth-cobalt-indides RE{sub 14}Co{sub 3}In{sub 3} (RE = Y, Tb, Dy, Ho, Er) were prepared in polycrystalline form from the elements by arc-melting. Small single crystals were grown through a special annealing sequence. The compounds were investigated on the basis of X-ray powder and single crystal data: Lu{sub 14}Co{sub 2}In{sub 3} (Gd{sub 14}Co{sub 3}In{sub 2.7}) type, P4{sub 2}/nmc, Z = 4, a = 959.0(1), c = 2319.1(5) pm, wR2 = 0.055, 2289 F{sup 2} values, 65 variables for Y{sub 13.90}Co{sub 2.99}In{sub 3.02}, a = 953.8(1), c = 2315.8(5) pm, wR2 = 0.108, 2357 F{sup 2} values, 65 variables for Tb{sub 13.92}Co{sub 3.01}In{sub 2.92}, a = 949.24(3), c = 2296.5(1) pm, wR2 = 0.129, 2518 F{sup 2} values, 65 variables for Dy{sub 13.90}Co{sub 2.97}In{sub 2.95}, a = 946.3(1), c = 2289.0(5) pm, wR2 = 0.099, 2297 F{sup 2} values, 64 variables for Ho{sub 14}Co{sub 2.80}In{sub 2.89}, and a = 941.0(1), c = 2274.2(5) pm, wR2 = 0.140, 2450 F{sup 2} values, 65 variables for Er{sub 13.83}Co{sub 2.88}In{sub 3.10}. All RE{sub 14}Co{sub 3}In{sub 3} indides show a small degree of In/Co mixing (between 7 and 16% Co) on the 4c In1 site and defects on the 8g Co1 positions (between 84 and 95% Co). Except for the holmium compound, the RE{sub 14}Co{sub 3}In{sub 3} intermetallics also reveal RE/In mixing on the 4c RE1 sites, leading to the refined compositions. The seven crystallographically independent RE sites have between 9 and 10 nearest RE neighbors. The RE{sub 14}Co{sub 3}In{sub 3} structures consist of a complex intergrowth of rare earth based polyhedra. Both cobalt sites have a distorted trigonal-prismatic rare earth coordination. An interesting feature is the In2-In2 dumb-bell with an In2-In2 distance of 300 pm (for Ho{sub 14}Co{sub 2.80}In{sub 2.89}). The crystal chemistry of the RE{sub 14}Co{sub 3}In{sub 3} indides is discussed. (orig.)

Investigation on the microstructure and mechanical properties of a cast Mg-6Zn-5Al-4RE alloy

International Nuclear Information System (INIS)

Xiao Wenlong; Jia Shusheng; Wang Jun; Wang, Jianli; Wang Limin

2008-01-01

Mg-6Zn-5Al-4RE (RE = Mischmetal, mass%) alloy was prepared by metal mould casting method. The microstructure and mechanical properties of the as-cast and heat-treated alloys were investigated. The results show that the phase compositions of the as-cast state alloy are supersaturated solid solution α-Mg, lamellar β-Al 12 Mg 17 , polygonal Al 3 RE and cluster Al 2 REZn 2 phases. The mechanical properties, especially the ultimate tensile strength and elongation of the alloy were significantly improved by the heat treatment. Fracture surface of tensile specimens was analyzed by optical microscope and scanning electron microscope

An Advanced Dictionary? Similarities and Differences between Duramazwi ReChiShona and Duramazwi Guru ReChiShona *

Directory of Open Access Journals (Sweden)

Emmanuel Chabata

2011-10-01

Full Text Available

Abstract: In this article a comparative analysis of Duramazwi ReChiShona (DRC and Duramazwi Guru ReChiShona (DGC is made. Both DRC and DGC are monolingual Shona dictionaries compiled by a team of researchers under the African Languages Lexical (ALLEX Project, now the African Languages Research Institute (ALRI. During the compilation process, DRC was known as the General Shona Dictionary and DGC as the Advanced Shona Dictionary. A simple analysis of these titles shows that the dictionaries are similar in some ways and also different in others. The writer tries to show the ways in which DGC is regarded as a more advanced dictionary when compared to DRC. Although the argument of the article is mainly built on those differences which make DGC the more advanced, attention is also paid to the similarities between the dictionaries.

Keywords: ALLEX PROJECT, ALRI, DURAMAZWI RECHISHONA, DURAMAZWI GURU RECHISHONA, DICTIONARY, SHONA, HEADWORD, SENSE, MONOLINGUAL DICTIONARY, CORPUS, IDIOM, PROVERB, PITHY SAYING

Opsomming: 'n Gevorderde woordeboek? Ooreenkomste en verskille tussen Duramazwi ReChiShona en Duramazwi Guru ReChiShona. In hierdie artikel word 'n vergelykende ontleding van Duramazwi ReChiShona (DRC en Duramazwi Guru ReChiShona (DGC gemaak. Sowel die DRC en DGC is eentalige Sjonawoordeboeke, saamgestel deur ?n span navorsers by die African Languages Lexical (ALLEX Project, tans die African Languages Research Institute (ALRI. Gedurende die samestellingsproses was DRC bekend as die Algemene Sjonawoordeboek en DGC as die Gevorderde Sjonawoordeboek. 'n Eenvoudige ontleding van hierdie titels toon dat die woordeboeke op sommige maniere eenders en op ander ook verskillend is. Die skrywer probeer die maniere aantoon waarop DGC beskou word as 'n meer gevorderde woordeboek wanneer dit met DRC vergelyk word. Alhoewel die argument van die artikel hoofsaaklik gebou is op daardie verskille wat DGC die gevorderdste maak, word ook aandag gegee aan

Didactical formulation of the Ampère law

International Nuclear Information System (INIS)

Barchiesi, Dominique

2014-01-01

The Ampère law is useful to calculate the magnetostatic field in the cases of distributions of current with high degree of symmetry. Nevertheless the magnetic field produced by a thin straight wire carrying a current I requires the Biot–Savart law and the use of the Ampère law leads to a mistake. A didactical formulation of the Ampère law is proposed to prevent misinterpretations. (letters and comments)

Refinement of the Al-rich part of the Al–Cu–Re phase diagram and atomic model of the ternary Al{sub 6.2}Cu{sub 2}Re phase

Energy Technology Data Exchange (ETDEWEB)

Samuha, S. [Department of Materials Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel); NRCN, P.O. Box 9001, Beer Sheva 84190 (Israel); Grushko, B. [MaTecK, Jülich D 52428 (Germany); PGI-5, Forschungszentrum Jülich, Jülich D 52425 (Germany); Meshi, L., E-mail: Louisa@bgu.ac.il [Department of Materials Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel); Ilse Katz Institute for Nanoscale Science & Technology, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel)

2016-06-15

Partial isothermal sections at 800, 650 and 590 °C were constructed for an Al-rich compositional range of Al–Cu–Re. The maximal solubility of Cu in the Al{sub 11}Re{sub 4}, h-Al{sub 4}Re and l-Al{sub 4}Re phases was found to be ∼6, 4.5, and 2.3 at% respectively, while the solubility of Re in the Al–Cu θ, η{sub 1} and ε{sub 2} phases was below 0.5 at%. Below 740 °C, a ternary hexagonal phase (P6{sub 3}, a = 1.1029 and c = 1.2746 nm) is formed in a small compositional range close to Al{sub 65}Cu{sub 25}Re{sub 10}. Its structural model was deduced by direct methods applied on the precession electron diffraction tomography data. - Highlights: • Al–Cu–Re was studied at 540–1030 °C up to 25 at% Re and 60 at% Cu. • Al{sub 11}Re{sub 4}, h-Al{sub 4}Re and l-Al{sub 4}Re dissolve 6, 4.5 and 2.3 at% Cu, respectively. • Earlier reported ternary compound Al{sub 8}CuRe was not confirmed. • Earlier reported ternary compound Al{sub 7}Cu{sub 2}Re is probably Al{sub 6.2}Cu{sub 2}Re. • Crystal structure of hexagonal Al{sub 6.2}Cu{sub 2}Re was solved.

Cette étrange matière

CERN Document Server

Kastler, Alfred

1976-01-01

La matière nous est connue et jusque dans sa structure intime : l'aspect qu'offre le monde industrialisé en est une preuve suffisante, la bombe atomique ou à hydrogène, un signe spectaculaire. Pourtant, selon Alfred Kastler, dont le témoignage en pareil domaine fait naturellement autorité, la matière mérite plus encore d'être appelée "étrange".

Selective Hydrodeoxygenation of Vegetable Oils and Waste Cooking Oils to Green Diesel Using a Silica-Supported Ir-ReOx Bimetallic Catalyst.

Science.gov (United States)

Liu, Sibao; Simonetti, Trent; Zheng, Weiqing; Saha, Basudeb

2018-05-09

High yields of diesel-range alkanes are prepared by hydrodeoxygenation of vegetable oils and waste cooking oils over ReO x -modified Ir/SiO 2 catalysts under mild reaction conditions. The catalyst containing a Re/Ir molar ratio of 3 exhibits the best performance, achieving 79-85 wt % yield of diesel-range alkanes at 453 K and 2 MPa H 2 . The yield is nearly quantitative for the theoretical possible long-chain alkanes on the basis of weight of the converted oils. The catalyst retains comparable activity upon regeneration through calcination. Control experiments using probe molecules as model substrates suggest that C=C bonds of unsaturated triglycerides and free fatty acids are first hydrogenated to their corresponding saturated intermediates, which are then converted to aldehyde intermediates through hydrogenolysis of acyl C-O bonds and subsequently hydrogenated to fatty alcohols. Finally, long-chain alkanes without any carbon loss are formed by direct hydrogenolysis of the fatty alcohols. Small amounts of alkanes with one carbon fewer are also formed by decarbonylation of the aldehyde intermediates. A synergy between Ir and partially reduced ReO x sites is discussed to elucidate the high activity of Ir-ReO x /SiO 2. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reaction of ReH sub 7 (PPh sub 3 ) sub 2 with silanes: Preparation and characterization of the first silyl polyhydride complexes, ReH sub 6 (SiR sub 3 )(PPh sub 3 ) sub 2 (SiR sub 3 = SiPh sub 3 , SiEt sub 3 , SiHEt sub 2 )

Energy Technology Data Exchange (ETDEWEB)

Luo, Xiaoliang; Baudry, D.; Boydell, P.; Charpin, P.; Nierlich, M.; Ephritikhine, M.; Crabtree, R.H. (Yale Univ., New Haven, CT (USA) CEA-CEN Saclay, Gif-sur-Yvette (France))

1990-04-18

Reaction of silanes with ReH{sub 7}(PPh{sub 3}){sub 2} (1) gives the novel rhenium silyl hexahydride complexes ReH{sub 6}(SiR{sub 3})(PPh{sub 3}){sub 2} (SiR{sub 3} = SiPh{sub 3} (2a), SiEt{sub 3} (2b), SiHEt{sub 2} (2c)), which have been fully characterized by IR and {sup 1}H, {sup 31}P, and {sup 13}C NMR spectroscopy and, in the case of 2a, by single-crystal x-ray crystallography. The spectroscopic and x-ray diffraction data suggest that 2a-c probably have a classical nine-coordinate tricapped trigonal-prismatic structure with the two phosphine ligands and the silyl group occupying the three equatorial sites and the six hydride ligands occupying the six axial positions. 2a has been obtained in two crystalline forms, one solvated (CH{sub 2}Cl{sub 2}) and the other unsolvated, and structures were determined on both. The crystal structures of crystals of unsolvated 2a and 2a {times} CH{sub 2} Cl{sub 2} are reported. The Re-Si bond lengths, 2.474 (4) {angstrom} (2a) and 2.475 (4) {angstrom} (2a {times} CH{sub 2}Cl{sub 2}), are shorter than the sum of the covalent radii of the Re and Si atoms (2.65 {angstrom}), which is unusual for a transition-metal silyl complex with a formal d{sup 0} configuration. 35 refs., 2 figs., 4 tabs.

Complexation of 188Re-phosphonates: in vitro and in vivo studies

International Nuclear Information System (INIS)

Faintuch, B.L.; Muramoto, E.; Faintuch, S.

2003-01-01

MDP (methylenediphosphonate) and HEDP (hydroxyethylidene diphosphonate), both disphosphonates, and EDTMP (ethylenediamine tetramethylene phosphonic acid), a tetraphosphonate ligand, have been previously labeled with 188 Re for use in metastatic bone-pain palliation. The aim of this study was a comparison between the three complexes 188 Re-MDP, 188 Re-HEDP and 188 Re-EDTMP concerning the complexation conditions, in order to achieve maximum yield, stability and bone uptake. Methods: MDP was dissolved in water and HEDP and EDTMP were dissolved in NaOH 1 N followed by reduction of pH with HCl 1 N. To all mixtures stannous chloride and 188 ReO 4 - were added in a nitrogen atmosphere. The preparations were heated in boiling water bath for 15 min. Yield as well as radiochemical stability was estimated by ITLC. Different concentrations of phosphonates and stannous chloride were evaluated. Biodistribution studies in Swiss mice were done for the three 188 Re-phosphonates that presented the best radiochemical yield. The optimal ligand concentration for maximum complexation was 85.2 mM for MDP, 72.8 mM for HEDP and 45.8 mM for EDTMP. The best amount of SnCl 2 .2H 2 O was 1.5 mg/mL for 188 Re-HEDP and 1 mg/mL for both 188 Re-MDP and 188 Re-EDTMP. In these conditions the three complexes showed a complexation rate above 95%. Reasonable radiochemical stability for 24 hours was achieved by 188 Re-EDTMP when employing ascorbic acid. All products showed a great uptake by the kidneys. 188 Re-EDTMP had the greatest uptake by femur (3.1 ± 0.2% ID/g) followed by 188 Re-MDP (1.2 ± 0.1% ID/g) and 188 Re-HEDP (1.0 ± 0.1% ID/g), 4 hours post injection. 188 Re-EDTMP displayed a femur bone/muscle ratio of 28.5, 188 Re-MDP 4.9 and 188 Re-HEDP 4.9. In conclusion 188 Re-EDTMP demonstrated the best potential as a radiopharmaceutical for bone cancer pain relief, encouraging further dosimetric studies and clinical trials. (orig.)

Suddenly included: cultural differences in experiencing re-inclusion.

Science.gov (United States)

Pfundmair, Michaela; Graupmann, Verena; Du, Hongfei; Frey, Dieter; Aydin, Nilüfer

2015-03-01

In the current research, we examined whether re-inclusion (i.e. the change from a previous state of exclusion to a new state of inclusion) was perceived differently by people with individualistic and collectivistic cultural backgrounds. Individualists (German and Austrian participants) but not collectivists (Chinese participants) experienced re-inclusion differently than continued inclusion: While collectivistic participants did not differentiate between both kinds of inclusion, individualistic participants showed reduced fulfilment of their psychological needs under re-inclusion compared to continued inclusion. The results moreover revealed that only participants from individualistic cultures expressed more feelings of exclusion when re-included than when continually included. These exclusionary feelings partially mediated the relationship between the different states of inclusion and basic need fulfilment. © 2014 International Union of Psychological Science.

Experimental determination of the hydrothermal solubility of ReS2 and the Re–ReO2 buffer assemblage and transport of rhenium under supercritical conditions

Directory of Open Access Journals (Sweden)

Wood Scott A

2002-01-01

Full Text Available To understand the aqueous species important for transport of rhenium under supercritical conditions, we conducted a series of solubility experiments on the Re–ReO2 buffer assemblage and ReS2. In these experiments, pH was buffered by the K–feldspar–muscovite–quartz assemblage; in sulfur-free systems was buffered by the Re–ReO2 assemblage; and and in sulfur-containing systems were buffered by the magnetite–pyrite–pyrrhotite assemblage. Our experimental studies indicate that the species ReCl40 is dominant at 400°C in slightly acidic to near-neutral, and chloride-rich (total chloride concentrations ranging from 0.5 to 1.0 M environments, and ReCl3+ may predominate at 500°C in a solution with total chloride concentrations ranging from 0.5 to 1.5 M. The results also demonstrate that the solubility of ReS2 is about two orders of magnitude less than that of ReO2. This finding not only suggests that ReS2 (or a ReS2 component in molybdenite is the solubility-controlling phase in sulfur-containing, reducing environments but also implies that a mixing process involving an oxidized, rhenium-containing solution and a solution with reduced sulfur is one of the most effective mechanisms for deposition of rhenium. In analogy with Re, TcS2 may be the stable Tc-bearing phase in deep geological repositories of radioactive wastes.

Need for re-skilltraining towards make in India initiative

Directory of Open Access Journals (Sweden)

Anita Singh

2016-12-01

Full Text Available With rapid change in global environment and technology, Indian corporate and industry is facing a big hurdle to fill existing jobs due to shortage of skilled manpower. To fill this gap the government has taken ‘Make in India’ initiative for skilling and re skilling manpower. Most of the Indian IT companies have shifted their focus from hiring to training and re skilling their employees at every level to match the needs of their client and make the organization cost effective. Training brings about attitudinal changes, improves skill, and there by improves job performance. The study attempts to understand attitude of employees towards imparting Re Skilling Training program, whether employees feels that re-skilling training is necessary or they are burdened by it. The basic focus of this paper is to identify the factor that influence employees attitude towards re-skilling. A survey is conducted to attain the objectives of the research. Respondents are the employees working in IT sector. Finding of the study includes that employees agree that re-killing is important for job growth and it also helps them in learning new technology and skills .They are of the opinion that re skilling provides them with better growth opportunities and enhances overall performance of the organization.

Seismic re-evaluation of French nuclear power plants

International Nuclear Information System (INIS)

Andrieu, R.

1995-01-01

After a presentation of the seismic inputs which have been taken into account in the design of the French Nuclear Power Plants, the re-assessed values of these inputs are shown. Some considerations about the specificity of the French PWR program with regard to the standardisation of plants are given together with the present objectives of seismic re-evaluations. Finally the main results of the seismic re-analysis being performed for the Phenix Fast Reactor are considered. (author)

Thermal expansion and conductivity of RE2Sn2O7 (RE = La, Nd, Sm, Gd, Er and Yb) pyrochlores

International Nuclear Information System (INIS)

Feng, J.; Xiao, B.; Zhou, R.; Pan, W.

2013-01-01

Graphical abstract: Calculated cohesive energies and formation enthalpies of RE 2 Sn 2 O 7 compounds. The formation enthalpies at 298 K are more close to the experimental values. -- The calculated cohesive energies and formation enthalpies of Rare earth stannate (RE 2 Sn 2 O 7 ) compounds are in good agreement with the corresponding experimental values. The thermal expansion coefficients (TECs) of rare earth stannates are 7–9 × 10 −6 K −1 at high temperature. The results show that local spin density approximation predicts smaller TECs than the real values. The computed thermal conductivity of RE 2 Sn 2 O 7 is 1.8–2.5 W (m · K) −1 at 1273 K using the Slack–Clarke model, indicating that RE 2 Sn 2 O 7 compounds exhibit good thermal insulating properties at high temperature

188W/188Re Generator System and Its Therapeutic Applications

Directory of Open Access Journals (Sweden)

A. Boschi

2014-01-01

Full Text Available The 188Re radioisotope represents a useful radioisotope for the preparation of radiopharmaceuticals for therapeutic applications, particularly because of its favorable nuclear properties. The nuclide decay pattern is through the emission of a principle beta particle having 2.12 MeV maximum energy, which is enough to penetrate and destroy abnormal tissues, and principle gamma rays (Eγ=155 keV, which can efficiently be used for imaging and calculations of radiation dose. 188Re may be conveniently produced by 188W/188Re generator systems. The challenges related to the double neutron capture reaction route to provide only modest yield of the parent 188W radionuclide indeed have been one of the major issues about the use of 188Re in nuclear medicine. Since the specific activity of 188W used in the generator is relatively low (<185 GBq/g, the eluted Re188O4- can have a low radioactive concentration, often ineffective for radiopharmaceutical preparation. However, several efficient postelution concentration techniques have been developed, which yield clinically useful Re188O4- solutions. This review summarizes the technologies developed for the preparation of 188W/188Re generators, postelution concentration of the 188Re perrhenate eluate, and a brief discussion of new chemical strategies available for the very high yield preparation of 188Re radiopharmaceuticals.

Person Re-Identification by Camera Correlation Aware Feature Augmentation.

Science.gov (United States)

Chen, Ying-Cong; Zhu, Xiatian; Zheng, Wei-Shi; Lai, Jian-Huang

2018-02-01

The challenge of person re-identification (re-id) is to match individual images of the same person captured by different non-overlapping camera views against significant and unknown cross-view feature distortion. While a large number of distance metric/subspace learning models have been developed for re-id, the cross-view transformations they learned are view-generic and thus potentially less effective in quantifying the feature distortion inherent to each camera view. Learning view-specific feature transformations for re-id (i.e., view-specific re-id), an under-studied approach, becomes an alternative resort for this problem. In this work, we formulate a novel view-specific person re-identification framework from the feature augmentation point of view, called Camera coR relation Aware Feature augmenTation (CRAFT). Specifically, CRAFT performs cross-view adaptation by automatically measuring camera correlation from cross-view visual data distribution and adaptively conducting feature augmentation to transform the original features into a new adaptive space. Through our augmentation framework, view-generic learning algorithms can be readily generalized to learn and optimize view-specific sub-models whilst simultaneously modelling view-generic discrimination information. Therefore, our framework not only inherits the strength of view-generic model learning but also provides an effective way to take into account view specific characteristics. Our CRAFT framework can be extended to jointly learn view-specific feature transformations for person re-id across a large network with more than two cameras, a largely under-investigated but realistic re-id setting. Additionally, we present a domain-generic deep person appearance representation which is designed particularly to be towards view invariant for facilitating cross-view adaptation by CRAFT. We conducted extensively comparative experiments to validate the superiority and advantages of our proposed framework over state

PSpectRe: a pseudo-spectral code for (P)reheating

International Nuclear Information System (INIS)

Easther, Richard; Finkel, Hal; Roth, Nathaniel

2010-01-01

PSpectRe is a C++ program that uses Fourier-space pseudo-spectral methods to evolve interacting scalar fields in an expanding universe. PSpectRe is optimized for the analysis of parametric resonance in the post-inflationary universe and provides an alternative to finite differencing codes, such as Defrost and LatticeEasy. PSpectRe has both second- (Velocity-Verlet) and fourth-order (Runge-Kutta) time integrators. Given the same number of spatial points and/or momentum modes, PSpectRe is not significantly slower than finite differencing codes, despite the need for multiple Fourier transforms at each timestep, and exhibits excellent energy conservation. Further, by computing the post-resonance equation of state, we show that in some circumstances PSpectRe obtains reliable results while using substantially fewer points than a finite differencing code. PSpectRe is designed to be easily extended to other problems in early-universe cosmology, including the generation of gravitational waves during phase transitions and pre-inflationary bubble collisions. Specific applications of this code will be described in future work

A study of factors affecting the labelling of tartrate with 188Re and the transchelation of the 188Re from the tartrate to a protein

International Nuclear Information System (INIS)

Sailerova, Eva; Billinghurst, M.W.

2003-01-01

The formation of 188 Re-tartrate for use in transchelation reactions and the transchelation of the 188 Re onto albumin was studied. Two labelled tartrate products were separated using a non-traditional mobile phase on ITLC strips. Tartrate labelling yield increases with pH but so does the instability when the product is exposed to air. Lower pH's are preferred when oxygen-free labelling conditions can be achieved. Higher tin levels protect against air oxidation. Stability of the Re-tartrate complex is supported by addition of ascorbic acid and ferrous sulphate, however both these agents decreased the rate of the formation of the Re-tartrate complex. The labelling efficiency of a perrhenate solution decreased with the time for which it is stored prior to the labelling reaction, depending on the radioactive concentration. Re-albumin transchelation efficiency increases with the tartrate concentration, while increased stability of the Re-tartrate complex lowers the transchelation yields of Re-albumin

Nye militære trends i den syriske borgerkrig

DEFF Research Database (Denmark)

Engen, Torben Toftgaard; Kjellund, Jon

2018-01-01

I den flerårige syriske borgerkrig har der fundet tre nye militære trends sted, der peger imod, at fremtidens landmilitære kampplads vil være væsensforskellig fra indsatserne i Irak og Afghanistan. Denne rapport analyserer de tre trends inden for digitaliseringen af den hybride krigsførelse og ka...

Crystallochemistry of rhenium compounds with metal-metal bonds

International Nuclear Information System (INIS)

Koz'min, P.A.; Surazhskaya, M.D.

1980-01-01

A review is presented including a brief description of atomic structure of 59 coordination rhenium compounds with metal-metal bond. The most important bond lengths and valent angles are presented for each compound. The dependence of rhenium-rhenium bond length on its multiplicity is discussed and possible causes of deviations from this dependence (namely, axial ligand presence, steric repulsion of ligands) are considered. On the basis of qualitative comparison of electronegativity of ligands in dimer compounds with quarternary bond of rhenium-rhenium a supposition is made on the influence of formal charge of atomic group and summary electro-negativity of ligands on the possibility of the metal-metal bond formation

Seismic re-evaluation process in Medzamor-2 NPP

International Nuclear Information System (INIS)

Zadoyan, P.

2000-01-01

Seismic re-evaluation process for Medzamor-2 NPP describes the following topics: program implementation status; re-evaluation program structure; regulatory procedure and review plan; current tasks and practice; and regulatory assessment and research programs

[Auguste Lumière (1862-1943). Cinematography...and microbiology].

Science.gov (United States)

Freney, Jean

2010-01-01

Auguste Lumière was the most inventive of the two brothers in the area of therapeutics and pharmacology. In 1896 he created his laboratory of experimental physiology where he discovered some organo-metallic derivatives active against syphilis, the oral vaccination against typhoid, vaseline gauze against burns. Unselfish amateur or real scientist he was a self-taught man who expended a lot of industrial activity even on erroneous scientific bases as he publicly refused the phenomenon of tuberculosis contagion in 1930.

Chromatographic 188W →188Re generator

International Nuclear Information System (INIS)

Khujaev, S.

2005-01-01

Full text: The main purpose of the generator - reception of daughter radioisotope Rhenium-188 from it by periodic elution for a long period of time (more than half-year). It is generally known that Rhenium-188, in the form of its complex connections, is applied in nuclear medicine in treatment and removal of painful syndromes. The generator possesses convenient nuclear-physical characteristics of a daughter radioisotope Rhenium-188. It is a source of (Irradiation with energy 2.12 MeV (98 %) with small contribution soft γ-radiation with energy 0.155 MeV (15 %). The Period of half-life destruction of radioisotope is 17 hours. The 188 W parent radioisotope for the generator is formed by irradiation of 186 W neutrons based on the following reaction: 186 W (n,γ) 187 W (n,γ) 188 W (69 days) → 188 Re (17 hours) + β The following were used as targets for irradiation: 1) Metal Tungsten (powder) of natural structure; 2) Metal Tungsten (plate) of natural structure; 3) Metal Tungsten (wire) of natural structure, d = 12 mm; 4) Metal Tungsten (powder) with enrichment on isotope 186 W - 99.79 %. The irradiated material was exposed to chemical processing with reception of radioactive solution of tungsten-188, from which sorption Tungsten was carried out onto sorbent as poly-wolframate-ions. It is established that Tungsten sorption depends on many factors as there are various chemical forms of Tungsten (VI) in water solutions, ratio of which depends on pH of the solution, concentration of Tungsten in the solution and presence of foreign ions. Tungsten sorption was carried out in static and in dynamic regimes. At dynamic regime the sorbent was placed directly in the generating column. The generator consisted of chromatographic columns with sorbent and radioisotope 188 W, eluting system and radiation protection. Rhenium-188 was taken from the generator as perrhenate sodium by elution of 0.9 % solution of chloride sodium in 10 ml. Technical characteristics of the generator

Re-evaluation of atomic bomb radiation

International Nuclear Information System (INIS)

Okajima, Shunzo

1984-01-01

The background and current status of the re-evaluation of atomic bomb (A-bomb) radiation doses are presented. Problems in re-evaluating radiation doses are discussed: spectra of gamma-rays and neutrons emitted in the air, A-bomb structures, and meterological elements should be taken into account. In Japan, in an attempt to estimate A-bomb radiation doses, radioactive residues contained in roof tiles, bricks, rocks, and teeth and shell button of clothes are being actually measured. (Namekawa, K.)

Irradiation induced precipitation in tungsten based, W-Re alloys

Science.gov (United States)

Williams, R. K.; Wiffen, F. W.; Bentley, J.; Stiegler, J. O.

1983-03-01

Tungsten-base alloys containing 5, 11, and 25 pct Re were irradiated in the EBR-II reactor. Irradiation temperatures ranged from 600 to 1500 °C. All compositions were irradiated to fluences in the range 4.3 to 6.1 X 1025 n/m2 (E > 0.1 MeV), and three 25 pct Re samples were also irradiated to 3.7 X 1026 n/m2 at temperatures 700 to 900 °C. Postirradiation examination included measurement of electrical resistivity at room temperature and lower temperatures, X-ray diffraction, optical metallography, microprobe analysis, and transmission electron microscopy. Irradiation induced resistivity decreases observed in most of the samples suggested second-phase precipitation. Complete results confirmed the precipitate formation in all samples, in disagreement with existing phase diagrams for the W-Re system. Electron diffraction showed the precipitates to be consistent with the cubic, Re-rich X-phase and inconsistent with the σ-phase. Large variations in precipitate morphology and distribution were observed between the different compositions and irradiation conditions. For the 5 and 11 pct Re-alloys, spherically symmetric strain fields surrounded the equiaxed precipitate particles, and were observed even where no particles were visible. These strain fields are believed to arise from local Re enrichment. Thermoelectric data show that the precipitation can lead to decalibration of W/Re thermocouples.

A study of the Al-rich part of the Al-Re alloy system

International Nuclear Information System (INIS)

Balanetskyy, S.; Grushko, B.

2008-01-01

The Al-rich part of the Al-Re phase diagram was reinvestigated by scanning and transmission electron microscopy, powder X-ray diffraction and differential thermal analysis. The earlier reported Al 12 Re, Al 6 Re, and Al 11 Re 4 phases were confirmed. Close to the Al 4 Re composition a high-temperature h-Al 4 Re and a low-temperature l-Al 4 Re phase were found to be formed at slightly different compositions. Both exhibited compositional ranges. A new phase was revealed close to the Al 3 Re composition. The Al 11 Re 4 phase is formed congruently at 1650 deg. C, Al 3 Re peritectically at 1610 deg. C, h-Al 4 Re peritectically at 1410 deg. C, l-Al 4 Re peritectically at ∼1000 deg. C, Al 6 Re peritectically at 813 deg. C and Al 12 Re peritectically at 746 deg. C. Finally, the Al 12 Re-(Al) eutectic is formed at 658 deg. C. The Al 3 Re and h-Al 4 Re are decomposed by eutectoid reactions at ∼946 and 833 deg., respectively. The structure of the h-Al 4 Re phase has not yet been clarified, but it is distinctly different from the Al 4 W phase suggested earlier. The structure of l-Al 4 Re was confirmed. The Al 3 Re phase was found to have a monoclinic structure with a = 0.5180(4) nm, b = 3.97641(9) nm, c = 0.4955(3) nm and β = 99.55(7) o

Re-irradiation for metastatic brain tumors with whole-brain radiotherapy

International Nuclear Information System (INIS)

Akiba, Takeshi; Kunieda, Etsuo; Kogawa, Asuka; Komatsu, Tetsuya; Tamai, Yoshifumi; Ohizumi, Yukio

2012-01-01

The objective of this study was to determine whether second whole-brain irradiation is beneficial for patients previously treated with whole-brain irradiation. A retrospective analysis was done for 31 patients with brain metastases who had undergone re-irradiation. Initial whole-brain irradiation was performed with 30 Gy/10 fractions for 87% of these patients. Whole-brain re-irradiation was performed with 30 Gy/10 fractions for 42% of these patients (3-40 Gy/1-20 fractions). Three patients underwent a third whole-brain irradiation. The median interval between the initial irradiation and re-irradiation was 10 months (range: 2-69 months). The median survival time after re-irradiation was 4 months (range: 1-21 months). The symptomatic improvement rate after re-irradiation was 68%, and the partial and complete tumor response rate was 55%. Fifty-two percent of the patients developed Grade 1 acute reactions. On magnetic resonance imaging, brain atrophy was observed in 36% of these patients after the initial irradiation and 74% after re-irradiation. Grade ≥2 encephalopathy or cognitive disturbance was observed in 10 patients (32%) after re-irradiation. Based on univariate analysis, significant factors related to survival after re-irradiation were the location of the primary cancer (P=0.003) and the Karnofsky performance status at the time of re-irradiation (P=0.008). A Karnofsky performance status ≥70 was significant based on multivariate analysis (P=0.050). Whole-brain re-irradiation for brain metastases placed only a slight burden on patients and was effective for symptomatic improvement. However, their remaining survival time was limited and the incidence of cognitive disturbance was rather high. (author)

Re-irradiation of recurrent esophageal cancer after primary definitive radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Suk; Lee, Chang Geol; Kim, Kyung Hwan; Kim, Tae Hyung [Dept. of Radiation Oncology, Yonsei University Health System, Yonsei University College of Medicine, Seoul (Korea, Republic of)

2012-12-15

For recurrent esophageal cancer after primary definitive radiotherapy, no general treatment guidelines are available. We evaluated the toxicities and clinical outcomes of re-irradiation (re-RT) for recurrent esophageal cancer. We analyzed 10 patients with recurrent esophageal cancer treated with re-RT after primary definitive radiotherapy. The median time interval between primary radiotherapy and re-RT was 15.6 months (range, 4.8 to 36.4 months). The total dose of primary radiotherapy was a median of 50.4 Gy (range, 50.4 to 63.0 Gy). The total dose of re-RT was a median of 46.5 Gy (range, 44.0 to 50.4 Gy). The median follow-up period was 4.9 months (range, 2.6 to 11.4 months). The tumor response at 3 months after the end of re-RT was complete response (n = 2), partial response (n = 1), stable disease (n = 2), and progressive disease (n = 5). Grade 5 tracheoesophageal fistula developed in three patients. The time interval between primary radiotherapy and re-RT was less than 12 months in two of these three patients. Late toxicities included grade 1 dysphagia (n = 1). Re-RT of recurrent esophageal cancer after primary radiotherapy can cause severe toxicity.

Re-irradiation of recurrent esophageal cancer after primary definitive radiotherapy

International Nuclear Information System (INIS)

Kim, Young Suk; Lee, Chang Geol; Kim, Kyung Hwan; Kim, Tae Hyung

2012-01-01

For recurrent esophageal cancer after primary definitive radiotherapy, no general treatment guidelines are available. We evaluated the toxicities and clinical outcomes of re-irradiation (re-RT) for recurrent esophageal cancer. We analyzed 10 patients with recurrent esophageal cancer treated with re-RT after primary definitive radiotherapy. The median time interval between primary radiotherapy and re-RT was 15.6 months (range, 4.8 to 36.4 months). The total dose of primary radiotherapy was a median of 50.4 Gy (range, 50.4 to 63.0 Gy). The total dose of re-RT was a median of 46.5 Gy (range, 44.0 to 50.4 Gy). The median follow-up period was 4.9 months (range, 2.6 to 11.4 months). The tumor response at 3 months after the end of re-RT was complete response (n = 2), partial response (n = 1), stable disease (n = 2), and progressive disease (n = 5). Grade 5 tracheoesophageal fistula developed in three patients. The time interval between primary radiotherapy and re-RT was less than 12 months in two of these three patients. Late toxicities included grade 1 dysphagia (n = 1). Re-RT of recurrent esophageal cancer after primary radiotherapy can cause severe toxicity.

The oxidation of ReCl_5 with oleum: synthesis and crystal structure of Re_2O_4Cl_4(SO_4)

International Nuclear Information System (INIS)

Betke, Ulf; Wickleder, Mathias S.

2012-01-01

The reaction of ReCl_5 and fuming sulfuric acid (25 % SO_3) in a sealed glass tube at 200 C led to red, needle shaped single crystals of Re_2O_4Cl_4(SO_4) (monoclinic, C2/c, a = 1501.8(2) pm, b = 1545.9(2) pm, c = 945.18(8) pm, β = 98.761(9) , Z = 8). In the crystal structure the [ReO_2] moieties are linked by [SO_4]"2"- tetrahedra to chains along the [101] direction. Each sulfate ion connects four rhenium atoms, additional two chloride ions complete the octahedral coordination sphere of each rhenium atom according to "1_∞[ReO_2_/_1Cl_2_/_1(SO_4)_2_/_4]. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Perks of Tracking What You're Eating

Science.gov (United States)

It’s important to keep track of the steps you’re taking toward nourishing your body with a healthier diet. By keeping track of what you’re eating—even for a couple of weeks— you may be able to identify patterns that are helping—or hurting—your goals for nourishing your body in a healthy way.

Re-utilization of concrete from decommissioned nuclear facilities by re-clinkering

International Nuclear Information System (INIS)

Costes, J.R.

1998-01-01

Usually concrete is reused as aggregates. To maximize reusing by producing a new concrete, separation of its fundamental components (aggregates, sand, cement) is required. But can already hydrated cement be re-clinkered and become new good cement again? This paper shows how specimen of pure cement paste of ordinary Portland cement was hydrated then crushed and reclinkerised. Chemical and, X ray diffraction analysis, electronic microscope coupled with X fluorescence observations, demonstrate that very few differences occurs in the cement paste before and after re-clinkering; mechanical properties of the reactivated powder are very satisfactory, even exceeding the strength of the original pure cement paste. As this process involves heating up to 1450 deg C, some of the contamination (caesium, ruthenium) may also be eliminated by volatilization and recovery on filters. This process could be very promising to complete recycle large quantities of low level contaminated concrete inside the nuclear industry as alternative to storage in specific and expensive dump, as it is now the case for steel materials. (authors)

Preparation and characterization of sintered Mo-Re alloys

International Nuclear Information System (INIS)

Morito, F.

1993-01-01

By the method of powder metallurgy, we have tried to fabricate Mo-Re alloys, which were electron beam weldable. Severe quality control was carried out during the whole fabrication process focused to reducing oxygen contamination. It is inevitable that the starting raw powders of Mo and Re were both high purity with 99.99 mass% up. Moreover, high vacuum sintering was performed before final sintering with high-purity hydrogen gas. As a result, we obtained electron beam weldable Mo-Re alloys, the total oxygen content of which was about 10 mass ppm or less, respectively. Several specimens were melted by electron beam welding (EBW) method. It was found that EBW gives an easy and effective survey to examine the weldability and the quality of the materials. Fracture surfaces examined by AES exhibited very low content of oxygen, carbon and nitrogen or that less than detectability limit. In conclusion, we have succeeded to obtain defect-free welds of sintered Mo-Re alloys. Furthermore it was found that Mo-Re alloys showed excellent potentialities not only in mechanical properties at low temperature but also in the respects of microstructure. (orig.)

MetReS, an Efficient Database for Genomic Applications.

Science.gov (United States)

Vilaplana, Jordi; Alves, Rui; Solsona, Francesc; Mateo, Jordi; Teixidó, Ivan; Pifarré, Marc

2018-02-01

MetReS (Metabolic Reconstruction Server) is a genomic database that is shared between two software applications that address important biological problems. Biblio-MetReS is a data-mining tool that enables the reconstruction of molecular networks based on automated text-mining analysis of published scientific literature. Homol-MetReS allows functional (re)annotation of proteomes, to properly identify both the individual proteins involved in the processes of interest and their function. The main goal of this work was to identify the areas where the performance of the MetReS database performance could be improved and to test whether this improvement would scale to larger datasets and more complex types of analysis. The study was started with a relational database, MySQL, which is the current database server used by the applications. We also tested the performance of an alternative data-handling framework, Apache Hadoop. Hadoop is currently used for large-scale data processing. We found that this data handling framework is likely to greatly improve the efficiency of the MetReS applications as the dataset and the processing needs increase by several orders of magnitude, as expected to happen in the near future.

Die Altäre von Selinunt

OpenAIRE

Voigts, Clemens

2014-01-01

In der Dissertation wurden die Altäre von Selinunt, einer griechischen Kolonie auf Sizilien, mit den Methoden der Bauforschung untersucht. Die neun behandelten Brandopferaltäre sind monumentale Quaderbauten, die bis zu 20 m Länge erreichen. Sie stammen aus der Blütezeit Selinunts, dem 6. und 5. Jh. v. Chr. Die Bauten waren bereits im 19. und 20. Jh. freigelegt worden und wurden nun in Bauaufnahmen dokumentiert, zeichnerisch rekonstruiert und zeitlich eingeordnet. Dabei ließ sich an ihnen eine...

Configurations of the Re-scan Confocal Microscope (RCM) for biomedical applications

NARCIS (Netherlands)

de Luca, G. M. R.; Desclos, E.; Breedijk, R. M. P.; Dolz-Edo, L.; Smits, G. J.; Bielefeld, P.; Picavet, L.; Fitzsimons, C. P.; Hoebe, R.; Manders, E. M. M.

2017-01-01

The new high-sensitive and high-resolution technique, Re-scan Confocal Microscopy (RCM), is based on a standard confocal microscope extended with a re-scan detection unit. The re-scan unit includes a pair of re-scanning mirrors that project the emission light onto a camera in a scanning manner. The

Configurations of the Re-scan Confocal Microscope (RCM) for biomedical applications

NARCIS (Netherlands)

De Luca, G.M.R.; Desclos, E.; Breedijk, R.M.P.; Dolz-Edo, L.; Smits, G.J.; Nahidiazar, L.; Bielefeld, P.; Picavet, L.; Fitzsimons, C.P.; Hoebe, R.; Manders, E.M.M.

The new high-sensitive and high-resolution technique, Re-scan Confocal Microscopy (RCM), is based on a standard confocal microscope extended with a re-scan detection unit. The re-scan unit includes a pair of re-scanning mirrors that project the emission light onto a camera in a scanning manner. The

Pulsed laser-deposited nanocrystalline GdB{sub 6} thin films on W and Re as field emitters

Energy Technology Data Exchange (ETDEWEB)

Suryawanshi, Sachin R.; More, Mahendra A. [Savitribai Phule Pune University, Department of Physics, Centre for Advanced Studies in Materials Science and Condensed Matter Physics, Pune (India); Singh, Anil K.; Sinha, Sucharita [Bhabha Atomic Research Centre, Laser and Plasma Technology Division, Trombay, Mumbai (India); Phase, Deodatta M. [UGC-DAE Consortium for Scientific Research Indore Centre, Indore (India); Late, Dattatray J. [CSIR-National Chemical Laboratory, Physical and Materials Chemistry Division, Pune (India)

2016-10-15

Gadolinium hexaboride (GdB{sub 6}) nanocrystalline thin films were grown on tungsten (W), rhenium (Re) tips and foil substrates using optimized pulsed laser deposition (PLD) technique. The X-ray diffraction analysis reveals formation of pure, crystalline cubic phase of GdB{sub 6} on W and Re substrates, under the prevailing PLD conditions. The field emission (FE) studies of GdB{sub 6}/W and GdB{sub 6}/Re emitters were performed in a planar diode configuration at the base pressure ∝10{sup -8} mbar. The GdB{sub 6}/W and GdB{sub 6}/Re tip emitters deliver high emission current densities of ∝1.4 and 0.811 mA/cm{sup 2} at an applied field of ∝6.0 and 7.0 V/μm, respectively. The Fowler-Nordheim (F-N) plots were found to be nearly linear showing metallic nature of the emitters. The noticeably high values of field enhancement factor (β) estimated using the slopes of the F-N plots indicate that the PLD GdB{sub 6} coating on W and Re substrates comprises of high-aspect-ratio nanostructures. Interestingly, the GdB{sub 6}/W and GdB{sub 6}/Re planar emitters exhibit excellent current stability at the preset values over a long-term operation, as compared to the tip emitters. Furthermore, the values of workfunction of the GdB{sub 6}/W and GdB6/Re emitters, experimentally measured using ultraviolet photoelectron spectroscopy, are found to be same, ∝1.6 ± 0.1 eV. Despite possessing same workfunction value, the FE characteristics of the GdB{sub 6}/W emitter are markedly different from that of GdB{sub 6}/Re emitter, which can be attributed to the growth of GdB{sub 6} films on W and Re substrates. (orig.)

The business of refractive laser assisted cataract surgery (ReLACS).

Science.gov (United States)

Berdahl, John P; Jensen, Matthew P

2014-01-01

Refractive Laser Assisted Cataract Surgery (ReLACS) combines the femtosecond laser with other noncovered tests and services in an attempt to reduce spectacle dependence in combination with cataract surgery. Significant interest is present among ophthalmologists who are considering adopting this technology, however significant capital outlays and continuing expenses can make the decision to adopt ReLACS foreboding. We review the financial considerations of ReLACS and review the trends seen in early adopters of this technology. Recent findings have shown that ReLACS is a growing segment of cataract surgery. Most practices who have implemented the technology have broken even and have a positive outlook on the financial return of implementing the ReLACS program. The average break-even analysis point for practices is around 230 cases a year. ReLACS is growing and appears to be a financial viable approach for many practices.

Itinerant-electron antiferromagnetism and superconductivity in bcc Cr-Re alloys

International Nuclear Information System (INIS)

Nishihara, Y.; Yamaguchi, Y.; Kohara, T.; Tokumoto, M.

1985-01-01

The magnetic and superconducting properties of bcc Cr-Re alloys with up to 40 at. % Re were studied via measurements of the magnetic susceptibility, electrical resistivity, and nuclear magnetic resonance of the Re nuclei. Antiferromagnetic order coexists with superconductivity above 18 at. % Re. The results were analyzed with the coexistence model of spin-density waves and superconductivity. In the Re-concentration range greater than 18 at. %, about 10% of the Fermi surface satisfies the nesting condition and the rest of it contributes to form the superconducting gap. This model also explains the increase in the superconducting transition temperature and the decrease in the magnetic susceptibility by annealing as a competing effect between spin-density waves and superconductivity

The Monge-Ampère equation

CERN Document Server

Gutiérrez, Cristian E

2016-01-01

Now in its second edition, this monograph explores the Monge-Ampère equation and the latest advances in its study and applications. It provides an essentially self-contained systematic exposition of the theory of weak solutions, including regularity results by L. A. Caffarelli. The geometric aspects of this theory are stressed using techniques from harmonic analysis, such as covering lemmas and set decompositions. An effort is made to present complete proofs of all theorems, and examples and exercises are offered to further illustrate important concepts. Some of the topics considered include generalized solutions, non-divergence equations, cross sections, and convex solutions. New to this edition is a chapter on the linearized Monge-Ampère equation and a chapter on interior Hölder estimates for second derivatives. Bibliographic notes, updated and expanded from the first edition, are included at the end of every chapter for further reading on Monge-Ampère-type equations and their diverse applications in th...

A study on plate anchor detailing systems of shear re-bar

International Nuclear Information System (INIS)

Tsurumaki, S.; Ujiie, K.; Nishikawa, T.; Kitayama, K.

1995-01-01

For shell walls and base slabs in reactor buildings, besides a large amount of main bars, numerous shear re-bars have been employed to resist to out-of-plane force. As a result , detailing work involving shear re-bar is extremely involved. For example, the employed re-bar anchor method differs from the ordinary methods in which, a end of shear re-bar with 135-degrees hook or with anchor plate type and another re-bar end with 90-degrees hook are used. However the structural characteristics in members using shear re-bar of the bolt-mounted anchor plate have not yet been examined. A test was performed to confirm the effects of anchor methods for shear re-bars on shearing behavior of members. This paper describes the test plan, method and results. (author). 12 figs., 7 tabs

You're Hired!

Science.gov (United States)

Weinstein, Margery

2011-01-01

"You're hired!" Those two words are easy to say, but it's not always easy to find the right employee. Success hinges on hiring interviews--and they require quite a bit of training to get right. Much of the work in identifying the best people for open positions falls to line-of-business managers. In this article, Verizon Wireless, Umpqua Bank,…

RDM lifetimes measurements in 179Re

International Nuclear Information System (INIS)

Chamoli, S.; Joshi, P.; Kumar, A.; Govil, I.M.; Singh, R.P.; Chatturvedi, L.

2001-01-01

The study of Re nuclei in the mass region from 170-190 is of particular interest as they lie in a region where the Nilsson orbitals exhibit large driving effects on the nuclear shape, presenting the strong possibility of shape coexistence. To see the variation of the deformation driving property of different bands and the other related phenomena like delay in band crossing frequency for intruder configuration h 92 in these nuclei with increasing in neutron number the lifetime measurement in 179 Re nucleus is done

Magnetic transitions in double perovskite Sr2FeRe1-xSbxO6 (0≤x≤0.9)

International Nuclear Information System (INIS)

Jung, Alexandra; Ksenofontov, Vadim; Reiman, Sergey; Therese, Helen Annal; Felser, Claudia; Tremel, Wolfgang; Kolb, Ute

2006-01-01

The double perovskites Sr 2 FeMO 6 (M=Re,Mo) belong to the important class of half-metallic magnetic materials. In this study we explore the effect of replacing the electronic 5d buffer element Re with variable valency by the main group element Sb with fixed valency. X-ray diffraction reveals Sr 2 FeRe 1-x Sb x O 6 (0 2 FeReO 6 changes to antiferromagnetic upon Sb substitution as was determined by magnetic susceptibility measurements. Samples up to a doping level of 0.3 are ferrimagnetic, while Sb contents higher than 0.6 result in an overall antiferromagnetic behavior. 57 Fe and 121 Sb Moessbauer spectroscopy specifies the valence state of Sb to be +5 within the whole range of substitution whereas the Fe valence state changes from +2.7 for the parent compound to +2.9 for Sr 2 FeRe 0.1 Sb 0.9 O 6 . Accordingly, Fe adopts the role of an electronic buffer element from Re upon heavy Sb doping. Additionally, 57 Fe Moessbauer results show a coexistence of ferri- and antiferromagnetic clusters within the same perovskite-type crystal structure in the Sb substitution range 0.3 2 FeReO 6 and Sr 2 FeRe 0.9 Sb 0.1 O 6 are ''purely'' ferrimagnetic and Sr 2 FeRe 0.1 Sb 0.9 O 6 contains antiferromagnetically ordered Fe sites only. Consequently, a replacement of the Re atoms by a nonmagnetic main group element such as Sb blocks the superexchange pathways -Fe-O-Re(Sb)-O-Fe- along the crystallographic axis of the perovskite unit cell and destroys the itinerant magnetism of the parent compound

Discriminative Multi-View Interactive Image Re-Ranking.

Science.gov (United States)

Li, Jun; Xu, Chang; Yang, Wankou; Sun, Changyin; Tao, Dacheng

2017-07-01

Given an unreliable visual patterns and insufficient query information, content-based image retrieval is often suboptimal and requires image re-ranking using auxiliary information. In this paper, we propose a discriminative multi-view interactive image re-ranking (DMINTIR), which integrates user relevance feedback capturing users' intentions and multiple features that sufficiently describe the images. In DMINTIR, heterogeneous property features are incorporated in the multi-view learning scheme to exploit their complementarities. In addition, a discriminatively learned weight vector is obtained to reassign updated scores and target images for re-ranking. Compared with other multi-view learning techniques, our scheme not only generates a compact representation in the latent space from the redundant multi-view features but also maximally preserves the discriminative information in feature encoding by the large-margin principle. Furthermore, the generalization error bound of the proposed algorithm is theoretically analyzed and shown to be improved by the interactions between the latent space and discriminant function learning. Experimental results on two benchmark data sets demonstrate that our approach boosts baseline retrieval quality and is competitive with the other state-of-the-art re-ranking strategies.

Effect of re-melting on particle distribution and interface formation in SiC reinforced 2124Al matrix composite

Energy Technology Data Exchange (ETDEWEB)

Mandal, Durbadal, E-mail: durbadal73@yahoo.co.in [MEF Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Viswanathan, Srinath [Dept of Metallurgical and Materials Engineering, University of Alabama, Tuscaloosa, AL (United States)

2013-12-15

The interface between metal matrix and ceramic reinforcement particles plays an important role in improving properties of the metal matrix composites. Hence, it is important to find out the interface structure of composite after re-melting. In the present investigation, the 2124Al matrix with 10 wt.% SiC particle reinforced composite was re-melted at 800 °C and 900 °C for 10 min followed by pouring into a permanent mould. The microstructures reveal that the SiC particles are distributed throughout the Al-matrix. The volume fraction of SiC particles varies from top to bottom of the composite plate and the difference increases with the decrease of re-melting temperature. The interfacial structure of re-melted 2124Al–10 wt.%SiC composite was investigated using scanning electron microscopy, an electron probe micro-analyzer, a scanning transmission electron detector fitted with scanning electron microscopy and an X-ray energy dispersive spectrometer. It is found that a thick layer of reaction product is formed at the interface of composite after re-melting. The experimental results show that the reaction products at the interface are associated with high concentration of Cu, Mg, Si and C. At re-melting temperature, liquid Al reacts with SiC to form Al{sub 4}C{sub 3} and Al–Si eutectic phase or elemental Si at the interface. High concentration of Si at the interface indicates that SiC is dissociated during re-melting. The X-ray energy dispersive spectrometer analyses confirm that Mg- and Cu-enrich phases are formed at the interface region. The Mg is segregated at the interface region and formed MgAl{sub 2}O{sub 4} in the presence of oxygen. The several elements identified at the interface region indicate that different types of interfaces are formed in between Al matrix and SiC particles. The Al–Si eutectic phase is formed around SiC particles during re-melting which restricts the SiC dissolution. - Highlights: • Re-melted composite shows homogeneous particle

Software Toolchain for Large-Scale RE-NFA Construction on FPGA

Directory of Open Access Journals (Sweden)

Yi-Hua E. Yang

2009-01-01

and O(n×m memory by our software. A large number of RE-NFAs are placed onto a two-dimensional staged pipeline, allowing scalability to thousands of RE-NFAs with linear area increase and little clock rate penalty due to scaling. On a PC with a 2 GHz Athlon64 processor and 2 GB memory, our prototype software constructs hundreds of RE-NFAs used by Snort in less than 10 seconds. We also designed a benchmark generator which can produce RE-NFAs with configurable pattern complexity parameters, including state count, state fan-in, loop-back and feed-forward distances. Several regular expressions with various complexities are used to test the performance of our RE-NFA construction software.

Automatic re-contouring in 4D radiotherapy

International Nuclear Information System (INIS)

Lu, Weiguo; Olivera, Gustavo H; Chen, Quan; Chen, Ming-Li; Ruchala, Kenneth J

2006-01-01

Delineating regions of interest (ROIs) on each phase of four-dimensional (4D) computed tomography (CT) images is an essential step for 4D radiotherapy. The requirement of manual phase-by-phase contouring prohibits the routine use of 4D radiotherapy. This paper develops an automatic re-contouring algorithm that combines techniques of deformable registration and surface construction. ROIs are manually contoured slice-by-slice in the reference phase image. A reference surface is constructed based on these reference contours using a triangulated surface construction technique. The deformable registration technique provides the voxel-to-voxel mapping between the reference phase and the test phase. The vertices of the reference surface are displaced in accordance with the deformation map, resulting in a deformed surface. The new contours are reconstructed by cutting the deformed surface slice-by-slice along the transversal, sagittal or coronal direction. Since both the inputs and outputs of our automatic re-contouring algorithm are contours, it is relatively easy to cope with any treatment planning system. We tested our automatic re-contouring algorithm using a deformable phantom and 4D CT images of six lung cancer patients. The proposed algorithm is validated by visual inspections and quantitative comparisons of the automatic re-contours with both the gold standard segmentations and the manual contours. Based on the automatic delineated ROIs, changes of tumour and sensitive structures during respiration are quantitatively analysed. This algorithm could also be used to re-contour daily images for treatment evaluation and adaptive radiotherapy

Re-Os geochronology of a Mesoproterozoic sedimentary succession, Taoudeni basin, Mauritania: Implications for basin-wide correlations and Re-Os organic-rich sediments systematics

Science.gov (United States)

Rooney, Alan D.; Selby, David; Houzay, Jean-Pierre; Renne, Paul R.

2010-01-01

The exceptionally well-preserved sedimentary rocks of the Taoudeni basin, NW Africa represent one of the world's most widespread (> 1 M km 2) Proterozoic successions. Hitherto, the sedimentary rocks were considered to be Mid Tonian based on Rb-Sr illite and glauconite geochronology of the Atar Group. However, new Re-Os organic-rich sediment (ORS) geochronology from two drill cores indicates that the Proterozoic Atar Group is ˜ 200 Ma older (1107 ± 12 Ma, 1109 ± 22 Ma and 1105 ± 37 Ma). The Re-Os geochronology suggests that the Rb-Sr geochronology records the age of diagenetic events possibly associated with the Pan African collision. The new Re-Os geochronology data provide absolute age constraints for recent carbon isotope chemostratigraphy which suggests that the Atar Group is Mesoproterozoic and not Neoproterozoic. The new Re-Os ORS geochronology supports previous studies that suggest that rapid hydrocarbon generation (flash pyrolysis) from contact metamorphism of a dolerite sill does not significantly disturb the Re-Os ORS systematics. Modelled contact conditions suggest that the Re-Os ORS systematics remain undisturbed at ˜ 650 °C at the sill/shale contact and ≥ 280 °C 20 m from the sill/shale contact. Moreover, the Re-Os geochronology indicates that the West African craton has a depositional history that predates 1100 Ma and that ORS can be correlated on a basin-wide scale. In addition, the Re-Os depositional ages for the ORS of the Taoudeni basin are comparable to those of ORS from the São Francisco craton, suggesting that these cratons are correlatable. This postulate is further supported by identical Os i values for the Atar Group and the Vazante Group of the São Francisco craton.

Production of carrier-free 188Re in the past ten years in Taiwan

International Nuclear Information System (INIS)

Bor-Tsung Hsieh; Institute of Nuclear Energy Research, Taiwan; Wan-Yu Lin; Tsai-Yueh Luo; Kai-Yuan Cheng

2007-01-01

Twenty clinical scale alumina-based 188 W/ 188 Re generators and carrier-free 188 Re has been produced at the Institute of Nuclear Energy Research (INER-Taiwan) for over ten years. 2845.6 GBq (76.9 Ci) of 188 Re-perrhenate solution has been eluted from generators during the past ten years. We have used the harvesting 188 Re solution for labeling radiopharmaceuticals, such as 188 Re-HEDP, 188 Re-MDP, 188 Re-microsphere, 188 Relipiodol, and 188 Re-sulfur colloid, etc. The average eluting yield of 188 Re is 78.6±5.8% that was investigated at 1115 harvesting times from 20 generators. Each generator can be used more than six months but the Millipore needs to be changed every two months for smooth harvesting and high yield of 188 Re solution. (author)

42 CFR 405.213 - Re-evaluation of a device categorization.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Re-evaluation of a device categorization. 405.213... Decisions That Relate to Health Care Technology § 405.213 Re-evaluation of a device categorization. (a... experimental/investigational (Category A) may request re-evaluation of the categorization decision. (2) A...

On the origin of reactivity enhancement/suppression upon sequential ligation: [Re(CO){sub x}]{sup +}/CH{sub 4} (x=0-3) couples

Energy Technology Data Exchange (ETDEWEB)

Zhou, Shaodong; Schlangen, Maria; Schwarz, Helmut [Institut fuer Chemie, Technische Universitaet Berlin (Germany); Li, Jilai [Institut fuer Chemie, Technische Universitaet Berlin (Germany); Institute of Theoretical Chemistry, Jilin University, Changchun (China)

2017-03-06

The thermal gas-phase reactions of rhenium carbonyl complexes [Re(CO){sub x}]{sup +} (x=0-3) with methane have been explored by using FT-ICR mass spectrometry complemented by high-level quantum chemical calculation. While it had been concluded in previous studies that addition of closed-shell ligands in general decreases the reactivity of metal ions, the current work provides an exception: the previously demonstrated inertness of atomic Re{sup +} towards methane is completely changed upon ligation with CO. Both [Re(CO)]{sup +} and [Re(CO){sub 2}]{sup +} bring about efficient dehydrogenation of the hydrocarbon under ambient conditions. However, addition of a third ligand to form [Re(CO){sub 3}]{sup +} completely quenches the reactivity. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

(Re)Discovering University Autonomy

DEFF Research Database (Denmark)

This book challenges traditional approach to university autonomy which is based on four pillars: organisational, financial, human resource, and academic. The main thesis is that a fuller understanding of university autonomy can only be obtained through a more holistic view of the complex inter-re...

Goal-Equivalent Secure Business Process Re-engineering

DEFF Research Database (Denmark)

Acosta, Hugo Andrés Lópes; Massacci, Fabio; Zannone, Nicola

2008-01-01

that they are somehow “equivalent”. In this paper we propose a method for passing from SI*, a modeling language for capturing and modeling functional, security, and trust organizational and system requirements, to business process specifications and vice versa. In particular, starting from an old secure business......The introduction of information technologies in health care systems often requires to re-engineer the business processes used to deliver care. Obviously, the new and re-engineered processes are observationally different and thus we cannot use existing model-based techniques to argue...... process, we reconstruct the functional and security requirements at organizational level that such a business process was supposed to meet (including the trust relations that existed among the members of the organization). To ensure that the re-engineered business process meets the elicited requirements...

Equilibrium polymerization models of re-entrant self-assembly

Science.gov (United States)

Dudowicz, Jacek; Douglas, Jack F.; Freed, Karl F.

2009-04-01

As is well known, liquid-liquid phase separation can occur either upon heating or cooling, corresponding to lower and upper critical solution phase boundaries, respectively. Likewise, self-assembly transitions from a monomeric state to an organized polymeric state can proceed either upon increasing or decreasing temperature, and the concentration dependent ordering temperature is correspondingly called the "floor" or "ceiling" temperature. Motivated by the fact that some phase separating systems exhibit closed loop phase boundaries with two critical points, the present paper analyzes self-assembly analogs of re-entrant phase separation, i.e., re-entrant self-assembly. In particular, re-entrant self-assembly transitions are demonstrated to arise in thermally activated equilibrium self-assembling systems, when thermal activation is more favorable than chain propagation, and in equilibrium self-assembly near an adsorbing boundary where strong competition exists between adsorption and self-assembly. Apparently, the competition between interactions or equilibria generally underlies re-entrant behavior in both liquid-liquid phase separation and self-assembly transitions.

A theoretical approach to the re-suspension factor

Directory of Open Access Journals (Sweden)

Magnoni M.

2012-04-01

Full Text Available The atmospheric re-suspension of radionuclides is a well-known phenomenon that consists in the re-injection into the atmosphere of previously deposited radioactivity. The process is driven by the action of wind on surfaces and can act as an additional source of radiation exposure by inhalation, after the deposition has finished. It is thus defined as the re-suspension factor, a parameter K generally considered as a time depending function and defined as the ratio of Ca, the volumetric air activity concentration (Bq m−3 and I0 (Bq m−2, the radioactivity deposition at time zero. The re-suspension factor concept is very useful in radioprotection in order to estimate the inhalation of radionuclides re-suspended from contaminated surfaces when direct atmospheric measurements are lacking or difficult to perform. However, the choice of the proper values of K is usually not a simple task, being quite site-specific and related to the meteorological, géomorphologie and environmental characteristics of the area to be studied. Moreover, several investigations showed clearly that the values of K are a decreasing function of time. For that reason, K values span several orders of magnitude: typical values in the range 10−5–10−10 m−1 are reported in literature for different environmental conditions and time elapsed since the deposition event. The current available models for the re-suspension factor are based on empirical formulas whose parameters are highly site dependent and cannot easily be related to some physical quantity. In this paper a simple physical model for the re-suspension factor is proposed and tested with available environmental radioactivity data (137Cs, collected since 1986 (Chernobyl fallout. The new model not only allows a satisfactory description of the experimental data like even the current empirical models do, but it is also able to connect the K values to quantities with a physical meaning (such as, for example a diffusion

Development of a technology for the preparation of 188W-188Re generators

International Nuclear Information System (INIS)

Oliveira, Alexandre de

2004-01-01

A big interest has recently arisen concerning the use of Rhenium-188 (188Re) for various medical applications. Tumor therapy with antibodies labeled with 188Re is the main application, but it is being studied its application in carcinomas of medullar thyroid, bone pain palliation and radionuclide synovectomy, among others. Rhenium-188 decays 79% to the ground state of stable 188Os (Eβ1max - 2,11 MeV) and 20% to the first excited state (Eβ2max = 1,97 MeV). The deexcitation of this state gives a 155 keV gamma ray (15r%) which can be detected by imaging. Another great advantage is the viability of carrier-free 188Re from the decay of 188W (t 1/2 = 69.4 days) in a generator system. The objective of this work is the development of the technology for the preparation of 188W- 188Re generators. To accomplish this, the steps of the work are: preparation of the targets of W; irradiation of W targets in order to measure the activation and radionuclidic impurities; development of 188W-188Re generators; development of a method for the quality control of 188Re: chemical, radiochemical and radionuclidic purities. The study of alumina-based generators was performed with the irradiation of targets of natural metallic W and W03 and showed that this kind of generator will only be viable with the importation of 188W, due to the low neutron flux of the Reactor IEA-R1 Reactor for the commercial routine production of this radioisotope, but the technology of production and quality control were successful. The gel type chromatographic generators of WZr were produced with natural WO3 targets and showed that, if enriched targets are to be used and with the power upgrade of the IEA-R1 Reactor, they can be produced by the Radiopharmacy Center at IPEN-SP. The quality control methodology were determined and the results were inside the limits given by the Pharmacopoeia. (author)

The effects of vascularized tissue transfer on re-irradiation

International Nuclear Information System (INIS)

Narayan, K.; Ashton, M.W.; Taylor, G.I.

1996-01-01

Purpose: Nowadays, radical re-irradiation of locally recurrent squamous cell carcinoma is being increasingly tried. The process usually involves some form of surgical excision and vascularized tissue transfer followed by re-irradiation. The aim of this study was to examine the extent of protection from the effects of re-irradiation provided by vascularized tissue transfer. Methods and Materials: One hundred Sprague Dawley rats had their left thighs irradiated to a total dose of 72Gy in 8 fractions, one fraction per day, 5 days per week. The rats were then divided into two groups: At 4 months, one half of the rats had 50% of their quadriceps musculature excised and replaced with a vascularized non-irradiated rectus abdominous myocutaneous flap. The other group served as the control. Six months following the initial radiotherapy all rats were then re-irradiated with either 75 or 90% of the original dose. Incidence of necrosis and the extent of necrosis was measured. Microvasculature of control, transplanted muscle and recipient site was studied by micro-corrosion cast technique and histology of cast specimen. tissues were sampled at pre-irradiation and at 2, 6 and 12 months post re-irradiation. Microvascular surface area was measured from the histology of cast specimen. Results: Necrosis in the control group was clinically evident at 6 weeks post re irradiation and by 10 months all rats developed necrosis. Forty per cent of the thigh that received 75% of the original dose on re-irradiation did not develop any necrosis by 13 months. Other groups developed necrosis to variable extents, however a rim of tissue around the graft always survived. The average thickness of surviving tissue was 9mm. (range being 4-25 mm). None of the transferred flap nor re-irradiated recipient quadriceps developed necrosis. Conclusion: 1. Transplanted rectus abdominus myocutaneous flap and undisturbed muscle have similar radiation tolerance. 2. Vascularized myocutaneous flap offers

Radiolabeling of rituximab with 188Re and 99mTc using the tricarbonyl technology

International Nuclear Information System (INIS)

Dias, Carla Roberta; Jeger, Simone; Osso, Joao Alberto; Mueller, Cristina; De Pasquale, Christine; Hohn, Alexander; Waibel, Robert; Schibli, Roger

2011-01-01

Introduction: The most successful clinical studies of immunotherapy in patients with non-Hodgkin's lymphoma (NHL) use the antibody rituximab (RTX) targeting CD20 + B-cell tumors. Rituximab radiolabeled with β - emitters could potentiate the therapeutic efficacy of the antibody by virtue of the particle radiation. Here, we report on a direct radiolabeling approach of rituximab with the 99m Tc- and 188 Re-tricarbonyl core (IsoLink technology). Methods: The native format of the antibody (RTX wt ) as well as a reduced form (RTX red ) was labeled with 99m Tc/ 188 Re(CO) 3 . The partial reduction of the disulfide bonds to produce free sulfhydryl groups (-SH) was achieved with 2-mercaptoethanol. Radiolabeling efficiency, in vitro human plasma stability as well as transchelation toward cysteine and histidine was investigated. The immunoreactivity and binding affinity were determined on Ramos and/or Raji cells expressing CD20. Biodistribution was performed in mice bearing subcutaneous Ramos lymphoma xenografts. Results: The radiolabeling efficiency and kinetics of RTX red were superior to that of RTX wt ( 99m Tc: 98% after 3 h for RTX red vs. 70% after 24 h for RTX wt ). 99m Tc(CO) 3 -RTX red was used without purification for in vitro and in vivo studies whereas 188 Re(CO) 3 -RTX red was purified to eliminate free 188 Re-precursor. Both radioimmunoconjugates were stable in human plasma for 24 h at 37 o C. In contrast, displacement experiments with excess cysteine/histidine showed significant transchelation in the case of 99m Tc(CO) 3 -RTX red but not with pre-purified 188 Re(CO) 3 -RTX red . Both conjugates revealed high binding affinity to the CD20 antigen (K d =5-6 nM). Tumor uptake of 188 Re(CO) 3 -RTX red was 2.5 %ID/g and 0.8 %ID/g for 99m Tc(CO) 3 -RTX red 48 h after injection. The values for other organs and tissues were similar for both compounds, for example the tumor-to-blood and tumor-to-liver ratios were 0.4 and 0.3 for 99m Tc(CO) 3 -RTX red and for 188 Re

Synthesis of ReN3 Thin Films by Magnetron Sputtering

Directory of Open Access Journals (Sweden)

G. Soto

2014-01-01

Full Text Available In this work ReNx films were prepared by reactive magnetron sputtering at room temperature and deposited on a silicon wafer. It was found that the diffractograms of the nitrogen-rich rhenium film are consistent with those produced by high-pressure high-temperature methods, under the assumption that the film is oriented on the substrate. Using density functional calculations it was found that the composition of this compound could be ReN3, instead of ReN2, as stated on previous works. The ReN3 compound fits in the Ama2 (40 orthorhombic space group, and due to the existence of N3 anions between Re layers it should be categorized as an azide. The material is exceptionally brittle and inherently unstable under indentation testing.

How the sedimentary Re/Mo ratio and Tl enrichments trace past and present opaline productivity

Science.gov (United States)

Böning, Philipp; Brumsack, Hans-Jürgen

2010-05-01

Here, we critically examine how the trace metals Mo, Re and (the rather enigmatic) Tl may serve as indicators of productivity events, as shown for Late Quaternary organic/opal-rich, fast accumulating sediments in upwelling areas off Peru and Namibia. In all Peruvian samples, Mo and Re are highly enriched. The ultimate trapping mechanism for Mo in the sediments is H2S availability, i.e., the intensity of sulfate reduction. Rhenium, by contrast, seems to accumulate via diffusion across the sediment-water interface according to the extent of reducing conditions (Böning et al., 2004; 2009). Opal was determined in Peruvian surface samples (0-1 cm, 16 stations, 85 to 1400 m water depth) and in a long Pleistocene core by Wolf (2002). Interestingly, low Re/Mo ratios (close to and below the sea water value, i. e. ≤ 2 * 10-4) as well as Tl are significantly correlated with opal contents in samples from the surface and the long core (r2 >0.8). Our data clearly show that such low Re/Mo ratios are typical of fine-grained sediments rich in fresh organic matter (no coarse material, no phosphorites). Off Namibia opal-rich sediments show high contents in Re and Mo and very low Re/Mo ratios, averaging 0.5 * 10-4. In short and long cores off Namibia and Peru, where Re/Mo is ≤ 1 * 10-4, Tl seems exclusively associated with opal (as seen in a significant correlation of Tl/Al with Si/Al; r2 >0.8). How do we explain such low Re/Mo ratios? Even if the trapping mechanisms are different for Mo and Re, Crusius et al's. (1996) Re-Mo relationship is quite useful. These authors proposed that a Re/Mo ratio close to the seawater ratio (0.8 * 10-4) reflect the quantitative removal of both Re and Mo from solution. But the Re/Mo ratio below the seawater ratio cannot be explained by diffusion of both elements and quantitative enrichment in the sediments. Indeed, the diffusion of Re and Mo is limited off Namibia and Peru given the enormous biogenic particle rain. Hence, we propose an additional

Solubility and superconductivity in RE(Ba2-xREx)Cu3O7+δ (RE = Nd, Sm, Eu, Gd, Dy)

International Nuclear Information System (INIS)

Zhang, K.; Dabrowski, B.; Segre, C.U.; Hinks, D.G.; Schuller, I.K.; Jorgensen, J.D.; Slaski, M.

1987-10-01

Solid solutions of RE(Ba 2-x RE x )Cu 3 O 7- δ (RE=Nd,Sm,Eu,Gd,Dy) for x=0 to x=0.5 have been investigated. X-ray and resistivity measurements show that there exists a solid solution region, through which, the structure changes from orthorhombic to tetragonal and the superconducting properties are depressed. The solubility limits depend strongly on the size of the rare-earth ion, with the smallest (Dy) showing no appreciable solubility. The superconducting transition temperature versus x for all of the rare-earth ion substitutions falls on a universal curve, indicating that the Ba sites are extremely ionic and magnetically isolated. 20 refs., 4 figs

Staged abdominal re-operation for abdominal trauma.

Science.gov (United States)

Taviloglu, Korhan

2003-07-01

To review the current developments in staged abdominal re-operation for abdominal trauma. To overview the steps of damage control laparotomy. The ever increasing importance of the resuscitation phase with current intensive care unit (ICU) support techniques should be emphasized. General surgeons should be familiar to staged abdominal re-operation for abdominal trauma and collaborate with ICU teams, interventional radiologists and several other specialties to overcome this entity.

Leadership processes for re-engineering changes to the health care industry.

Science.gov (United States)

Guo, Kristina L

2004-01-01

As health care organizations seek innovative ways to change financing and delivery mechanisms due to escalated health care costs and increased competition, drastic changes are being sought in the form of re-engineering. This study discusses the leader's role of re-engineering in health care. It specifically addresses the reasons for failures in re-engineering and argues that success depends on senior level leaders playing a critical role. Existing studies lack comprehensiveness in establishing models of re-engineering and management guidelines. This research focuses on integrating re-engineering and leadership processes in health care by creating a step-by-step model. Particularly, it illustrates the four Es: Examination, Establishment, Execution and Evaluation, as a comprehensive re-engineering process that combines managerial roles and activities to result in successfully changed and reengineered health care organizations.

Synthesis of a '4+1' Re(V) complex from Re(III), and its ...

African Journals Online (AJOL)

bis(2-hydroxybenzyl)-2-(2-aminoethyl)dimethylamine) was prepared from the oxidation of [ReCl3(MeCN)(PPh3)2] by dioxygen in the presence of H2had in ethanol. This reaction was done under reflux conditions for a relatively short reaction ...

188Re labeling and biodistribution of magnetic nanoparticles for the tumor targeting

International Nuclear Information System (INIS)

Li Guiping; Zhang Hui; Wang Yongxian; Zhang Chunfu

2006-01-01

Objective: To prepare 188 Re labeled monoclonal antibody (Herceptin)-coated magnetic nanoparticles for tumor targeting and to study its biodistribution in mice. Methods: Herceptin and histidine were covalently linked to the amine group upon silica-coated magnetic nanoparticles modified by N-[3-(trimethyoxysilyl)prowl]-ethylenediamine using glutaraldehyde method. The Herceptin-coated magnetic nanoparticles and Herceptin were radiolabeled with 188 Re by a direct labelling method, whereas the histidine-coated magnetic nanoparticles was radiolabeled with 188 Re using fac-[ 188 Re(CO) 3 (H 2 0) 3 ] + as a precursor. The labelling efficiency and immunoreactivity as well as labelling stability were determined. Also, the biodistribution of 188 Re-magnetic and 188 Re-Herceptin-magnetic nanoparticles were observed in mice. Results: Herceptin-coated magnetic nanoparticles was characterized by transmission electron microscope (TEM) with diameter about 60 nm, while histidine-coated magnetic nanoparticles about 30 nm. The labeling efficiency for 188 Re-Herceptin, 188 Re-magnetic nanoparticles and 188 Re-Herceptin-magnetic nanoparticles were all > 90% and had a better stability in vitro. The immunoreactivity of Herceptin linked to magnetic nanoparticles was still high. The biodistribution in mice was shown that 188 Re-magnetic nanoparticles and 188 Re-Herceptin- magnetic nanoparticles had higher radioactivity levels in blood. Magnetic nanoparticles with diameter of 30 or 60 nm had a long half-life in blood stream and were accumulated in liver. Conclusion: The efficiency and stability of labelling Herceptin-coated magnetic nanoparticles and labelling magnetic nanoparticles with 188 Re are suitable for in vivo study in tumor-beating nude mice models. (authors)

Ternary gallides RE_4Rh_9Ga_5, RE_5Rh_1_2Ga_7 and RE_7Rh_1_8Ga_1_1 (RE=Y, La-Nd, Sm, Gd, Tb). Intergrowth structures with MgCu_2 and CaCu_5 related slabs

International Nuclear Information System (INIS)

Seidel, Stefan; Rodewald, Ute C.; Poettgen, Rainer; Janka, Oliver

2017-01-01

Fourteen ternary gallides RE_4Rh_9Ga_5, RE_5Rh_1_2Ga_7 and RE_7Rh_1_8Ga_1_1 (RE=Y, La-Nd, Sm, Gd, Tb) were synthesized from the elements by arc-melting, followed by different annealing sequences either in muffle or induction furnaces. The samples were characterized through Guinier powder patterns and the crystal structures of Ce_4Rh_9Ga_5, Ce_5Rh_1_2Ga_7, Ce_7Rh_1_8Ga_1_1, Nd_5Rh_1_0_._4_4_(_4_)Ga_8_._5_6_(_4_), Nd_4Rh_9Ga_5 and Gd_4Rh_9Ga_5 were refined from single crystal X-ray diffractometer data. The new gallides are the n=2, 3 and 5 members of the RE_2_+_n Rh_3_+_3_n Ga_1_+_2_n structure series in the Parthe intergrowth concept. The slabs of these intergrowth structures derive from the cubic Laves phase MgCu_2 (Mg_2Ni_3Si as ternary variant) and CaCu_5 (CeCo_3B_2 as ternary variant). Only the Nd_5Rh_1_0_._4_4_(_4_)Ga_8_._5_6_(_4_) crystal shows Rh/Ga mixing within the Laves type slabs. Magnetic susceptibility measurements reveal Pauli paramagnetism for Y_4Rh_9Ga_5 and Curie-Weiss paramagnetism for Gd_4Rh_9Ga_5 and Tb_4Rh_9Ga_5. Low-temperature data show ferromagnetic ordering at T_C=78.1 (Gd_4Rh_9Ga_5) and 55.8 K (Tb_4Rh_9Ga_5).

Regional Energy Deployment System (ReEDS)

Energy Technology Data Exchange (ETDEWEB)

Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

2011-12-01

The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

The collaborative ec project ReCosy - 16203

International Nuclear Information System (INIS)

Kienzler, Bernhard; Buckau, Gunnar

2009-01-01

The Collaborative Project (CP) ReCosy (Redox Controlling Systems) was established in 2008. It falls within the EURATOM program and is implemented within the European Commission's 7. Framework Program. Main objectives of CP ReCosy are the sound understanding of redox phenomena controlling the long-term release/retention of radionuclides in nuclear waste disposal and providing tools to apply the results to Performance Assessment/Safety Case. Although redox is not a new geochemical problem, different questions are still not resolved and thus raised by implementers and scientists. Radionuclide redox transformations on minerals are considered to be decisive scenarios in various FEP lists. 32 institutions from 13 European countries contribute to the 4-years CP by i) development of advanced analytical tools, ii) investigations of processes responsible for redox control (thermodynamically and kinetically controlled processes, surface reactions and microbial processes), iii) provision of required data on redox controlling processes, and iv) response of the disposal systems to external/internal disturbances. Systems which are investigated comprise simple very well defined ones under controlled laboratory conditions, complex laboratory systems, near-natural systems in the laboratory, real systems, and near-field systems controlled spent nuclear fuel. The scientific results of the CP ReCosy are reported during annual workshops (AW). The first AW took place in February 10-12, 2009. The scientific contributions underwent a peer review and are published in the form of workshop proceedings together with scientific-technical overview papers of the different project work packages. The present paper summarizes the main results obtained after the first year of ReCosy. The status during the project preparation phase of the CP ReCosy is published elsewhere. (authors)

Zinc allocation and re-allocation in rice

Science.gov (United States)

Stomph, Tjeerd Jan; Jiang, Wen; Van Der Putten, Peter E. L.; Struik, Paul C.

2014-01-01

Aims: Agronomy and breeding actively search for options to enhance cereal grain Zn density. Quantifying internal (re-)allocation of Zn as affected by soil and crop management or genotype is crucial. We present experiments supporting the development of a conceptual model of whole plant Zn allocation and re-allocation in rice. Methods: Two solution culture experiments using 70Zn applications at different times during crop development and an experiment on within-grain distribution of Zn are reported. In addition, results from two earlier published experiments are re-analyzed and re-interpreted. Results: A budget analysis showed that plant zinc accumulation during grain filling was larger than zinc allocation to the grains. Isotope data showed that zinc taken up during grain filling was only partly transported directly to the grains and partly allocated to the leaves. Zinc taken up during grain filling and allocated to the leaves replaced zinc re-allocated from leaves to grains. Within the grains, no major transport barrier was observed between vascular tissue and endosperm. At low tissue Zn concentrations, rice plants maintained concentrations of about 20 mg Zn kg−1 dry matter in leaf blades and reproductive tissues, but let Zn concentrations in stems, sheath, and roots drop below this level. When plant zinc concentrations increased, Zn levels in leaf blades and reproductive tissues only showed a moderate increase while Zn levels in stems, roots, and sheaths increased much more and in that order. Conclusions: In rice, the major barrier to enhanced zinc allocation towards grains is between stem and reproductive tissues. Enhancing root to shoot transfer will not contribute proportionally to grain zinc enhancement. PMID:24478788

Re-Greening Ethiopia: History, Challenges and Lessons

Directory of Open Access Journals (Sweden)

Mulugeta Lemenih

2014-07-01

Full Text Available In Ethiopia, deforestation rates remain high and the gap between demand and domestic supply of forest products is expanding, even though government-initiated re-greening efforts began over a century ago. Today, over 3 million hectares (ha of degraded forest land are under area exclosure; smallholder plantations cover 0.8 million ha; and state-owned industrial plantations stagnate at under 0.25 million ha. This review captures experiences related to re-greening practices in Ethiopia, specifically with regards to area exclosure and afforestation and reforestation, and distills lessons regarding processes, achievements and challenges. The findings show that farmers and non-governmental organizations (NGOs are the main players, and that the private sector has so far played only a small role. The role of the government was mixed: supportive in some cases and hindering in others. The challenges of state- and NGO-led re-greening practices are: inadequate involvement of communities; poorly defined rehabilitation objectives; lack of management plans; unclear responsibilities and benefit-sharing arrangements; and poor silvicultural practices. The lessons include: a more active role for non-state actors in re-greening initiatives; more attention to market signals; devolution of management responsibility; clear definition of responsibilities and benefit-sharing arrangements; and better tenure security, which are all major factors to success.

Interstitial-mediated diffusion and clustering for transmutation elements Re and Os precipitation in W

Science.gov (United States)

Zhou, Hong-Bo; Li, Yu-Hao; Lu, Guang-Hong

Under high energy (14 eV) neutrons irradiation in nuclear fusion devoices, tungsten (W) will undergo transmutation to its near-neighbors in the periodic table, such as rhenium (Re), osmium (Os), etc. The transmutation elements Re and Os will precipitate and form new Re/Os-rich phase, and further significantly degrade the mechanical properties of W. Here, we have investigated the mechanism for the irradiation-induced Re/Os clustering in W using the first-principles method and thermodynamic models. It is found that there is strong attraction between Re/Os and self-interstitial atom (SIA) in W. The SIA can be easily trapped by Re/Os once overcoming a low energy barrier, and form W-Re/Os complex dumbbell. The diffusion energy barrier of W-Re/Os is much lower than that of Re/Os diffusing via mono-vacancy or even vacancy clusters. Further, the W-Re/Os can be easily trapped by the substitutional Re/Os atoms, and form high stable Re-Re/Os-Os dumbbell structure. Most importantly, the Re-Re/Os-Os dumbbell can serve as trapping centre for subsequent interstitial-Re/Os, leading to the growth of Re/Os-rich clusters in W. Our finding suggests an interstitial-mediated mechanism for the irradiation-induced Re/Os clustering in W. This research is supported by the National Magnetic Confinement Fusion Program with Grant No. 2013GB109002, and the National Natural Science Foundation of China with Grant No. 11675011.

EPA RE-Powering Screening Shapefile

Data.gov (United States)

U.S. Environmental Protection Agency — The U.S. Environmental Protection Agency (EPA) Office of Land and Emergency Management (OLEM) Center for Program Analysis (CPA) initiated the RE-Powering America’s...

Mid-temperature deep removal of hydrogen sulfide on rare earth (RE = Ce, La, Sm, Gd) doped ZnO supported on KIT-6: Effect of RE dopants and interaction between active phase and support matrix

International Nuclear Information System (INIS)

Li, Lu; Zhou, Pin; Zhang, Hongbo; Meng, Xianglong; Li, Juexiu; Sun, Tonghua

2017-01-01

Highlights: • Various rare earth (RE)-doped ZnO/KIT-6 sorbents were prepared via sol-gel method. • La showed the highest efficiency on promoting ZnO/KIT-6 desulfurization activity. • The morphology of ZnO on KIT-6 played a crucial role for the reactivity. • The most initial factor of improving reactivity by RE was surface chemical property. • Crystallinity, host-guest interaction were also important to ZnO state on support. - Abstract: Rare earth oxides (RE = Ce, La, Sm and Gd) doped ZnO supported on KIT-6 sorbents (RE-ZnO/KIT-6) were synthesized by sol-gel method and their performance for deep removal of H 2 S (bellow 0.1 ppmv) from gas stream at medium temperature was tested. The RE dopants (except Ce) significantly enhance the deep desulfurization capacity of ZnO/KIT-6 sorbent and maintained higher sulfur uptake capacities upon multiple cycles of regeneration by a simple thermal oxidation in 10 v% of O 2 in N 2 atmosphere. The results of SAXS, XRD, N 2 physisorption, TEM, FIIR, and XPS implied that the KIT-6 structure of loading metal oxides remained intact. It was found that RE could hinder the ZnO crystal ripening during calcination resulted in smaller ZnO particles, enhance the interaction of ZnO and silica matrix to improve the dispersion of active phase on KIT-6. Furthermore, by increasing the outlayer electron density of Zn atom and oxygen transfer ability, the synergistic effect considered to be favorable for RE-ZnO/KIT-6 sulfidation. Even though the performance of improving ZnO dispersion was weaker than that of Sm and Gd, La-ZnO/KIT-6 performs the best deep desulfurizers by changing the surface chemical atmosphere for ZnO. Steam in the gas stream inhibited the capture of H 2 S by ZnO in the sorbents, in the case of La-ZnO/KIT-6, the steam content should control as lower as 5 v% to ensure the desulfurization efficiency and precision.

Density changes observed in pure molybdenum and Mo-41Re after irradiation in FFTF/MOTA

International Nuclear Information System (INIS)

Garner, F.A.; Greenwood, L.R.

1993-01-01

Pure molybdenum and Mo-41wt% Re, in both the 20% cold-worked and aged and the annealed and aged conditions, were irradiated in FFTF/MOTA to exposures as high as 111 dpa. Pure molybdenum appears to approach a saturation swelling level that is independent of the starting state. Cold-worked and aged molybdenum initially swells at a higher rate than that of solution annealed and aged molybdenum and overshoots the saturation level at lower irradiation temperatures. This requires that part of the accumulated swelling be removed to approach saturation, probably by void shrinkage. The alloy Mo-41Re exhibits a more complex behavior with the annealed and aged condition initially swelling faster, but eventually the density change of both conditions begins to turn downward and tends toward densification. The role of solid transmutation to Tc, Re, and Os is though to be very important in the irradiation behavior of these two metals. Calculations of transmutant generation are provided for FFTF, HFIR and STARFIRE spectra

On Fourier re-expansions

OpenAIRE

Liflyand, E.

2012-01-01

We study an extension to Fourier transforms of the old problem on absolute convergence of the re-expansion in the sine (cosine) Fourier series of an absolutely convergent cosine (sine) Fourier series. The results are obtained by revealing certain relations between the Fourier transforms and their Hilbert transforms.

Re-discovering indigenous knowledge – Ulwazi Lwemveli for ...

African Journals Online (AJOL)

Therefore, the imperative to re-discover and re-store IK cannot be underestimated since building on this knowledge is particularly effective in helping to reach those living in rural communities. This knowledge is often the main asset they control, and certainly one with which they are more familiar. The case studies discussed ...

Third-Party Evaluation of Petro Tex Hydrocarbons, LLC, ReGen Lubricating Oil Re-refining Process

Energy Technology Data Exchange (ETDEWEB)

Compere, A L [ORNL; Griffith, William {Bill} L [ORNL

2009-04-01

This report presents an assessment of market, energy impact, and utility of the PetroTex Hydrocarbons, LLC., ReGen process for re-refining used lubricating oil to produce Group I, II, and III base oils, diesel fuel, and asphalt. PetroTex Hydrocarbons, LLC., has performed extensive pilot scale evaluations, computer simulations, and market studies of this process and is presently evaluating construction of a 23 million gallon per year industrial-scale plant. PetroTex has obtained a 30 acre site in the Texas Industries RailPark in Midlothian Texas. The environmental and civil engineering assessments of the site are completed, and the company has been granted a special use permit from the City of Midlothian and air emissions permits for the Texas Commission on Environmental Quality.

Re-injection accelerates groundwater clean up at Fernald, Fluor Fernald, Inc

International Nuclear Information System (INIS)

Dave Brettschneider; William Hertel; Ken Broberg

2000-01-01

A successful one year long, field scale demonstration of the use of groundwater re-infection at Fernald was recently completed bringing DOE one step closer to achieving an accelerated site remediation (DOE 2000). The demonstration marks the end of a several year effort to evaluate whether: re-injection could be conducted efficiently at Fernald, and if the approved aquifer remedy at Fernald would benefit by incorporating re-infection. Evaluation of re-injection technology involved not only technical considerations, but also participation and cooperation of regulators and stakeholders. The demonstration was considered to be unique in that it was integrated into the design of the current approved aquifer remedy and utilized the existing remediation infrastructure. Information collected during the demonstration indicated that re-injection wells could be operated efficiently at Fernald and that the current approved groundwater remedy should be modified to include the use of re-injection

Salvage Re-Irradiation for Recurrent Head and Neck Cancer

International Nuclear Information System (INIS)

Lee, Nancy; Chan, Kelvin; Bekelman, Justin E.; Zhung, Joanne; Mechalakos, James; Narayana, Ashwatha; Wolden, Suzanne; Venkatraman, Ennapadam S.; Pfister, David; Kraus, Dennis; Shah, Jatin; Zelefsky, Michael J.

2007-01-01

Purpose: To present a retrospective review of treatment outcomes for recurrent head and neck (HN) cancer patients treated with re-irradiation (re-RT) at a single medical center. Methods and Materials: From July 1996-September 2005, 105 patients with recurrent HN cancer underwent re-RT at our institution. Sites included were: the neck (n = 21), nasopharynx (n 21), paranasal sinus (n = 18), oropharynx (n = 16), oral cavity (n = 9), larynx (n = 10), parotid (n = 6), and hypopharynx (n = 4). The median prior RT dose was 62 Gy. Seventy-five patients received chemotherapy with their re-RT (platinum-based in the majority of cases). The median re-RT dose was 59.4 Gy. In 74 (70%), re-RT utilized intensity-modulated radiation therapy (IMRT). Results: With a median follow-up of 35 months, 18 patients were alive with no evidence of disease. The 2-year loco-regional progression-free survival (LRPFS) and overall survival rates were 42% and 37%, respectively. Patients who underwent IMRT, compared to those who did not, had a better 2-year LRPF (52% vs. 20%, p < 0.001). On multivariate analysis, non-nasopharynx and non-IMRT were associated with an increased risk of loco-regional (LR) failure. Patients with LR progression-free disease had better 2-year overall survival vs. those with LR failure (56% vs. 21%, p < 0.001). Acute and late Grade 3-4 toxicities were reported in 23% and 15% of patients. Severe Grade 3-4 late complications were observed in 12 patients, with a median time to development of 6 months after re-RT. Conclusions: Based on our data, achieving LR control is crucial for improved overall survival in this patient population. The use of IMRT predicted better LR tumor control. Future aggressive efforts in maximizing tumor control in the recurrent setting, including dose escalation with IMRT and improved chemotherapy, are warranted

Digital Intraoral Imaging Re-Exposure Rates of Dental Students.

Science.gov (United States)

Senior, Anthea; Winand, Curtis; Ganatra, Seema; Lai, Hollis; Alsulfyani, Noura; Pachêco-Pereira, Camila

2018-01-01

A guiding principle of radiation safety is ensuring that radiation dosage is as low as possible while yielding the necessary diagnostic information. Intraoral images taken with conventional dental film have a higher re-exposure rate when taken by dental students compared to experienced staff. The aim of this study was to examine the prevalence of and reasons for re-exposure of digital intraoral images taken by third- and fourth-year dental students in a dental school clinic. At one dental school in Canada, the total number of intraoral images taken by third- and fourth-year dental students, re-exposures, and error descriptions were extracted from patient clinical records for an eight-month period (September 2015 to April 2016). The data were categorized to distinguish between digital images taken with solid-state sensors or photostimulable phosphor plates (PSP). The results showed that 9,397 intraoral images were made, and 1,064 required re-exposure. The most common error requiring re-exposure for bitewing images was an error in placement of the receptor too far mesially or distally (29% for sensors and 18% for PSP). The most common error requiring re-exposure for periapical images was inadequate capture of the periapical area (37% for sensors and 6% for PSP). A retake rate of 11% was calculated, and the common technique errors causing image deficiencies were identified. Educational intervention can now be specifically designed to reduce the retake rate and radiation dose for future patients.

Re-vitalizing an indigenous language

DEFF Research Database (Denmark)

Hansen, Annette Skovsted

2014-01-01

The re-vitalization of indigenous languages depend on political and legal support and the imple-mentation of language rights depend on knowledge of vocabulary and grammar structures of the individual languages. Throughout the nineteenth century world, compilers of dictionaries adapted indigenous...... languages to match standards defined in nation-building and, thereby, enabled latent possibilities for indigenous populations to re-vitalize their languages in connection with the United Nations Year for Indigenous Peoples in 1993, and the first United Nations Decade for Indigenous Peoples, 1995......–2004. This article focuses on dictionaries of the languages of the Ainu populations in the borderlands between the nation-states Japan and Russia. The main argument is that the Ainu Cultural Promotion Act promulgated in 1997 had a significant impact on the production and purpose of Ainu dictionaries...

Successful Enterprise System Re-Implementation

DEFF Research Database (Denmark)

Svejvig, Per

2017-01-01

Achieving success in enterprise systems (ES) implementations is challenging. The success rate is not high in view of the sums invested by many organizations in these companywide systems. The literature is charged with reasons for unsuccessful implementations, such as a lack of top management...... support and insufficient change management. Contrary to this research, empirical data from an ES re-implementation in a Scandinavian high-tech company shows successful implementation despite many problematic shifts in outsourcing partners. Therefore, it is natural to ask: why was the re......-implementation of the ES at SCANDI successful despite the major troubles encountered during the project? Building an analysis based on ten Critical Success Factors (CSFs) combined with an investigation into the institutional structures at play, we present several reasons for the successful implementation. The CSF analysis...

Invention/Re-invention

OpenAIRE

Mera, M.

2009-01-01

This article examines the relationship between texts that are re-invented for different media and/or contexts including: film remakes, prequels and sequels, video games that become films and vice versa, internet mashups, and television series that move across geographical borders. The article points to significant sources in this emerging field and presents some of the challenges that arise in relation to its study. In particular questions of originality, fidelity, repetition and difference a...

Disease elimination and re-emergence in differential-equation models.

Science.gov (United States)

Greenhalgh, Scott; Galvani, Alison P; Medlock, Jan

2015-12-21

Traditional differential equation models of disease transmission are often used to predict disease trajectories and evaluate the effectiveness of alternative intervention strategies. However, such models cannot account explicitly for probabilistic events, such as those that dominate dynamics when disease prevalence is low during the elimination and re-emergence phases of an outbreak. To account for the dynamics at low prevalence, i.e. the elimination and risk of disease re-emergence, without the added analytical and computational complexity of a stochastic model, we develop a novel application of control theory. We apply our approach to analyze historical data of measles elimination and re-emergence in Iceland from 1923 to 1938, predicting the temporal trajectory of local measles elimination and re-emerge as a result of disease migration from Copenhagen, Denmark. Copyright © 2015 Elsevier Ltd. All rights reserved.

Five-Year NRHP Re-Evaluation of Historic Buildings Assessment

Energy Technology Data Exchange (ETDEWEB)

Ullrich, R A; Heidecker, K R

2011-09-12

The Lawrence Livermore National Laboratory (LLNL) 'Draft Programmatic Agreement among the Department of Energy and the California State Historic Preservation Officer Regarding Operation of Lawrence Livermore National Laboratory' requires a review and re-evaluation of the eligibility of laboratory properties for the National Register of Historic Places (NRHP) every five years. The original evaluation was published in 2005; this report serves as the first five-year re-evaluation. This re-evaluation includes consideration of changes within LLNL to management, to mission, and to the built environment. it also determines the status of those buildings, objects, and districts that were recommended as NRHP-eligible in the 2005 report. Buildings that were omitted from the earlier building list, those that have reached 50 years of age since the original assessment, and new buildings are also addressed in the re-evaluation.

Sparse Contextual Activation for Efficient Visual Re-Ranking.

Science.gov (United States)

Bai, Song; Bai, Xiang

2016-03-01

In this paper, we propose an extremely efficient algorithm for visual re-ranking. By considering the original pairwise distance in the contextual space, we develop a feature vector called sparse contextual activation (SCA) that encodes the local distribution of an image. Hence, re-ranking task can be simply accomplished by vector comparison under the generalized Jaccard metric, which has its theoretical meaning in the fuzzy set theory. In order to improve the time efficiency of re-ranking procedure, inverted index is successfully introduced to speed up the computation of generalized Jaccard metric. As a result, the average time cost of re-ranking for a certain query can be controlled within 1 ms. Furthermore, inspired by query expansion, we also develop an additional method called local consistency enhancement on the proposed SCA to improve the retrieval performance in an unsupervised manner. On the other hand, the retrieval performance using a single feature may not be satisfactory enough, which inspires us to fuse multiple complementary features for accurate retrieval. Based on SCA, a robust feature fusion algorithm is exploited that also preserves the characteristic of high time efficiency. We assess our proposed method in various visual re-ranking tasks. Experimental results on Princeton shape benchmark (3D object), WM-SRHEC07 (3D competition), YAEL data set B (face), MPEG-7 data set (shape), and Ukbench data set (image) manifest the effectiveness and efficiency of SCA.

Sol–gel synthesis of long-lasting phosphors CdSiO3: Mn2+, RE3+ (RE = Tb, Eu, Nd) and luminescence mechanism research

International Nuclear Information System (INIS)

Qu, Xiaofei; Cao, Lixin; Liu, Wei; Su, Ge; Wang, Pingping; Schultz, Isabel

2012-01-01

Highlights: ► New long-lasting CdSiO 3 : Mn 2+ , RE 3+ (RE = Tb, Eu, Nd) phosphors were synthesized by a sol–gel method. ► The afterglow performance of the CdSiO 3 : Mn 2+ , Eu 3+ phosphor was the best. ► The role of RE 3+ co-doped into the CdSiO 3 : Mn 2+ matrix was discussed in this paper. -- Abstract: Mn 2+ and RE 3+ (RE = Tb, Eu, Nd) co-doped CdSiO 3 orange phosphors were prepared at 1050 °C by a sol–gel method. The phase and crystallinity of the synthesized materials were investigated by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The luminescence characteristics were analyzed using photoluminescence (PL) spectra, afterglow decay curves, long-lasting phosphorescence spectra, and thermoluminescence (TL) spectra. Due to the difference in co-doped rare earth ionic radii, it varied greatly in trap density and trap depth caused by the different defects deriving from RE 3+ ions co-doping into the CdSiO 3 : Mn 2+ host. The afterglow intensity and time for these samples increased as follows: CdSiO 3 : Mn 2+ 0.2%, Nd 3+ 0.8% 3 : Mn 2+ 0.4%, Tb 3+ 0.8% 3 : Mn 2+ 0.4%, Eu 3+ 0.3%. CdSiO 3 : Mn 2+ 0.4%, Eu 3+ 0.3% had the best afterglow properties, which could be due to the proper traps formed by Eu 3+ ions co-doping into the host. The role of RE 3+ co-doped into the CdSiO 3 : Mn 2+ matrix and the possible long-lasting phosphorescence process was also discussed in this paper.

Factors having implications on re-retinal detachments after silicone oil removal

Directory of Open Access Journals (Sweden)

Manish P Nagpal

2012-01-01

Full Text Available Aim: To investigate factors having implications on re-retinal detachments (reRD after silicone oil removal (SOR. Materials and Methods: A retroprospective study of 412 eyes (with attached retina after vitrectomy with silicone oil for rhegmatogenous RD which underwent SOR was conducted and were followed up for six months after SOR. They were studied for various factors like encirclage, 360° retinopexy, oil emulsification at the time of SOR, duration of oil tamponade and previous retinal surgeries prior to SOR with their implications on reRD after SOR. Results: Encirclage, 360 laser barrage, both, emulsification of oil (P=0.021, P=0.001, P=0.001, P=0.001, respectively were associated with lower risks of reRD after SOR whereas duration of tamponade (P=0.980 was not. Conclusion: Factors like encirclage, 360 retinopexy, their combination, oil emulsification reduced the incidence of re RD after SOR whereas duration of tamponade does not have statistical significant correlation with re RD after SOR.

Re-Envisioning Human Rights in the Light of Arendt and Rancière: Towards an Agonistic Account of Human Rights Education

Science.gov (United States)

Zembylas, Michalinos

2017-01-01

This article takes up Arendt's "aporetic" framing of human rights as well as Rancière's critique and suggests that reading them together may offer a way to re-envision human rights and human rights education (HRE)--not only because they make visible the perplexities of human rights, but also in that they call for an agonistic…

Anisotropy of the optical absorption in layered single crystals of MoRe0.001Se1.999

International Nuclear Information System (INIS)

Vora, Mihir M.; Vora, Aditya M.

2007-01-01

Energy gap of MoRe 0.001 Se 1.999 single crystal has been determined by fundamental absorption methods. The incident light was polarized along c-axis of the crystals. The interpretion of the data is given within frameworks of two and three dimensional models. Both direct and indirect transitions are involved in the absorption process. The indirect transition was found to be allowed with two phonons participating in the process. The three dimensional model could be used to describe the optical properties of the single crystal. The energy gaps depend upon the amount of the intercalating Re material, which show the anisotropy of the chemical bonds. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

A review of irradiation induced re-solution in oxide fuels

International Nuclear Information System (INIS)

Turnbull, J.A.

1980-01-01

The paper reviews the existing experimental evidence for irradiation induced re-solution and also possible explanations for the mechanism. The importance of re-solution is considered with regard to intragranular bubbles and the accumulation of gas on grain boundaries. It is concluded that re-solution is most effective at low temperatures and could account for the present concern over gas release in high burn-up water reactor fuel assemblies. (author)

Study on the pharmacal of 186,188Re-SZ39

International Nuclear Information System (INIS)

Zu Jianhua; Wu Yuanfang; Dong Mo; Li Huiyuan; ZhangYulong

2000-01-01

The stability, immunocompetence and cytotoxicity in tumor as well as tumor inhibiting rate of 186,188 Re-SZ39 are investigated. The results indicate that 186,188 Re-SZ39 is stable in vivo by imaging and the volume of tumor of nude mice reduced obviously. So 186,188 Re-SZ39 has a strong cytotoxicity effect against glioma cells and is of good prospect as immuno-radiotherapeutic agent

Final Technical Report, reEnergize Program

Energy Technology Data Exchange (ETDEWEB)

Wamstad-Evans, Kristi [City of Omaha; Williams, Eric [City of Omaha; Kubicek, Jason [City of Omaha

2013-12-27

The reEnergize Program helped to build a market for residential and commercial energy evaluations and upgrades. The program provided incentives to encourage participants to save energy, save money, and make their homes and businesses more safe, healthy, and comfortable. As part of the Better Buildings Neighborhood Program (BBNP), the successful investment of this $10 million grant toward market development was the first grant funding collaboration between the cities of Omaha and Lincoln. Through more than three years of work, thousands of participants, contractors, and community members worked together to make the reEnergize Program a demonstration of how to “Build Energy Smart Communities.”

Phase relations and superconductivity in the binary Re-Si system

International Nuclear Information System (INIS)

Jorda, J.L.; Ishikawa, M.; Muller, J.

1982-01-01

The phase diagram of the Re-Si system was reinvestigated by means of high temperature methods of analysis. Several modifications were found to the existing diagram. An extended rhenium solid solution (up to 10 at.% Si) was established with a rapid quenching technique. Within this terminal solid solution, the superconducting transition temperature increased from 1.7 to 5.2 K. The phase corresponding to the Re 5 Si 3 compound was homogeneous at 33 at.% Si. The peritectically formed equiatomic compound decomposed eutectoidally at 1650 0 C and was superconducting at 1.5 K. The compound ReSi 2 was found to be off stoichiometric, occurring at the composition ReSisub(1.8). (Auth.)

Re-Engineering Marketing (RM

Directory of Open Access Journals (Sweden)

Bozhidar Iv. Hadzhiev

2010-12-01

Full Text Available La globalización, el auge de la economía, el progreso de la e-net economía, y el gran dinamismo de las relaciones comerciales se están constituyendo como una función progresiva en constante crecimiento, predeterminando la utilización de unas pocas nuevas oportunidades para aumentar la eficacia de las empresas. Llegados a este punto, a través del prisma de los métodos de reingeniería en el presente artículo se muestran algunos problemas básicos y las oportunidades existentes para la Reingeniería del Marketing (RM.Globalization, the rise of the economy, the progress of the e-net economy, and the high dynamics of business relationships are developing as one of the permanently rising progressive functions, predetermining the use of a few new opportunities for increasing effectiveness of the industry companies. At this point, through the prism of Re-engineering methods, a few basic problems and opportunities for Re-engineering Marketing (RM are presented in this paper.

Effects of rare-earth substitution on the stability and electronic structure of REZnOSb (RE = La-Nd, Sm-Gd) investigated via first-principles calculations

International Nuclear Information System (INIS)

Guo Kai; Man Zhenyong; Cao Qigao; Chen Haohong; Guo Xiangxin; Zhao Jingtai

2011-01-01

Graphical abstract: The structure stability of REZnOSb decreases with varying rare-earth from La to Gd because of the increased binding energy. Research highlights: → As increasing the atomic number of the RE, the structural stability of REZnOSb decreases. → Varying the rare-earth elements from La to Gd, the covalent interactions between [ZnSb] and [LaO] layer are enhanced by 4f-electrons. → The electrical transport properties of REZnOSb could be improved using the large atomic number of the RE. - Abstract: The structural stability, chemical bonding, Mulliken populations, and charge-density distribution of REZnOSb (RE = La-Nd, Sm-Gd) were investigated by first-principles calculations. Unit cell parameters calculated by the generalized gradient approximation (GGA) are in better agreement with experimental results than those derived from the local density approximation (LDA). Binding energy comparisons indicate that the structural stability of REZnOSb decreases with the increment of the atomic number of the RE, as confirmed by X-ray diffraction (XRD) results. Semimetal or narrow band-gap semiconductor behaviors are found for selected REZnOSb. Moreover, chemical bonding analysis shows that there exist considerable polar covalent interactions between the participating atoms. It also reveals that the [ZnSb] layers receive some electrons from the [LaO] layers (donor) as an electrons acceptor and holes transport tunnel. The covalent interactions between the [ZnSb] and [LaO] layers, which are enhanced by 4f-electrons of the RE, are supposed to improve the electrical transport properties.

Performance Spread of Re-entrant System Structures

DEFF Research Database (Denmark)

Nielsen, Erland Hejn

2001-01-01

-to-day operations. It might well be the case that those badly behaving systems merely constitute a set with a measure of almost zero. The key parameters that determine whether a re-entrant system is one of the badly behaving ones are essentially flow-structure, processing times and rules of priority between...... satisfactory. They are all vulnerable to certain job flow patterns and process time settings to a significant degree. The LBFS priority policy therefore presents itself not only as a stable, but also the safe and robust choice par excellence in relation to the control of re-entrant systems....... different job-classes on specific machines. Let us therefore face a re-entrant flow-shop production set-up in an order-driven production system, by which I mean that the flow structure relative to each production-batch shows great variability and where the size of the individual batches is quite large. One...

Kanegelo ya Nimirode: Re lebelela diphihlelelo t�a gagwe ka lefsa

Directory of Open Access Journals (Sweden)

Elelwani B. Farisani

2011-03-01

Full Text Available Kanegelo ya Hama/Nimirode e �omi�it�we go gatelela Bathobaso ba Afrika-Borwa le ba Amerika. Taodi�wana ye e lekola Nimirode ka lefsa le go t�ea magato a go bu�et�a seriti sa gagwe le sa Bathobaso sekeng.Seo se tlo dirwa ka dikgato t�e tlhano ka mo tlase. Sa mathomo, re tlo lekola dimelo t�a bana ba Noage, go kwe�i�a Nimirode, yo e lego yena �edi ye kgolo ya taodi�wana ye. Sa bobedi re tlo lebelela ka fao bangwadi ba bangwe ba t�welet�ago seswant�ho sa go befa sa Nimirode. Sa boraro, re tlo sekaseka tiri�o ya kanegelo ya Hama/Nimirode go gatelela le go dira Bathobaso makgoba. Sa bone, re tlo sekaseka diphihlelelo le dikatlego t�a Nimirode. Mo re tlo tsepelela diphihlelelo t�a gagwe t�e tharo t�e kgolo bjalo ka go ba mmu�i wa maemo, motsomi yo maatla le moagi. Nepo ya karolo ye ke go ganet�ana le tshekatsheko ya go se be botse ye e nepilwego Nimirode nakong ya go feta. Re tlo tlalelet�a ka go fa tshekatsheko ye e tebilego ya thogako godimo ga Hama/Ku�e/Nimirode. Sa bohlano, ebile e le sa mafelelo, re tlo t�welet�a nyanyeng bohlokwa bja kanegelo ya Nimirode go bao ba bego ba gatelet�we le go ba makgoba ka baka la temana ye. Re tlo nepi�a Afrika-Borwa.

The re-identification risk of Canadians from longitudinal demographics

Science.gov (United States)

2011-01-01

Background The public is less willing to allow their personal health information to be disclosed for research purposes if they do not trust researchers and how researchers manage their data. However, the public is more comfortable with their data being used for research if the risk of re-identification is low. There are few studies on the risk of re-identification of Canadians from their basic demographics, and no studies on their risk from their longitudinal data. Our objective was to estimate the risk of re-identification from the basic cross-sectional and longitudinal demographics of Canadians. Methods Uniqueness is a common measure of re-identification risk. Demographic data on a 25% random sample of the population of Montreal were analyzed to estimate population uniqueness on postal code, date of birth, and gender as well as their generalizations, for periods ranging from 1 year to 11 years. Results Almost 98% of the population was unique on full postal code, date of birth and gender: these three variables are effectively a unique identifier for Montrealers. Uniqueness increased for longitudinal data. Considerable generalization was required to reach acceptably low uniqueness levels, especially for longitudinal data. Detailed guidelines and disclosure policies on how to ensure that the re-identification risk is low are provided. Conclusions A large percentage of Montreal residents are unique on basic demographics. For non-longitudinal data sets, the three character postal code, gender, and month/year of birth represent sufficiently low re-identification risk. Data custodians need to generalize their demographic information further for longitudinal data sets. PMID:21696636

Thermal decomposition of RE(C2H5CO2)3·H2O (RE = Dy, Tb, Gd, Eu and Sm)

DEFF Research Database (Denmark)

Grivel, Jean-Claude

2014-01-01

The thermal decomposition of Dy(III), Tb(III), Gd(III), Eu(III), and Sm(III) propionate monohydrates was studied in argon by means of simultaneous differential thermal analysis and thermogravimetry, infrared-spectroscopy, X-ray diffraction, and optical microscopy. After dehydration, which takes......, an intermediate stage involving a RE2O(C2H5CO2)4 composition was evidenced in the case of the Eu- and Sm-propionates. For all compounds, further decomposition of RE2O2CO3 into the corresponding sesquioxides (RE2O3) is accompanied by the release of CO2. The thermal decomposition of Dy- and Tb-propionates occurs...

Weak ferromagnetism in Re0.67Ca0.33FeO3 (Re=La, Sm, Gd) nanoparticles

International Nuclear Information System (INIS)

Li Jiangong; Kou Xinli; Qin Yong; He Haiying

2003-01-01

Perovskite-type complex ferrite Re 0.67 Ca 0.33 FeO 3 (Re=La, Sm, Gd) nanoparticles of nearly the same particle size were prepared using sol-gel method. The influence of rare-earth ions on weak ferromagnetism in the Re 0.67 Ca 0.33 FeO 3 nanoparticles has been studied. The spontaneous magnetization M s of the Sm 0.67 Ca 0.33 FeO 3 nanoparticles is greater than that of Gd 0.67 Ca 0.33 FeO 3 nanoparticles; and M s of Gd 0.67 Ca 0.33 FeO 3 nanoparticles is greater than that of La 0.67 Ca 0.33 FeO 3 nanoparticles. The ferromagnetic component arising from the Fe sublattice increases with the decreasing rare-earth ionic radii. The magnetization of the rare-earth ions in the Sm 0.67 Ca 0.33 FeO 3 nanoparticles is smaller than that in the Gd 0.67 Ca 0.33 FeO 3 nanoparticles. The influences of the geometric and intrinsic magnetic characters of rare-earth ions as well as the particle size of the nanoparticles on weak ferromagnetism are discussed

Revision Total Hip Arthoplasty: Factors Associated with Re-Revision Surgery

OpenAIRE

Khatod, M; Cafri, G; Inacio, MCS; Schepps, AL; Paxton, EW; Bini, SA

2015-01-01

The survivorship of implants after revision total hip arthroplasty and risk factors associated with re-revision are not well defined. We evaluated the re-revision rate with use of the institutional total joint replacement registry. The purpose of this study was to determine patient, implant, and surgeon factors associated with re-revision total hip arthroplasty.A retrospective cohort study was conducted. The total joint replacement registry was used to identify patients who had undergone revi...

Re-Emergent Tremor of Parkinson's Disease Masquerading as Essential Tremor

Directory of Open Access Journals (Sweden)

Sarah Morgan

2016-03-01

Full Text Available Background: The re-emergent tremor of Parkinson’s disease (PD is generally recognized as a postural tremor. Phenomenology Shown: A PD patient with a re-emergent tremor occurring during a task (spiral drawing, which on the surface produced a tremor that resembled that of essential tremor (ET. Educational Value: Researchers and clinicians should be aware of features of this re-emergent tremor to help distinguish it from that of ET.

ions (RE = La, Pr, Nd, Sm, Gd and Dy)

Indian Academy of Sciences (India)

) zirconia), tendency of phase transformation (tetragonal to monoclinic () zirconia) and lattice strain were studied with mechanical property e.g. tensile strength of sol–gel derived ZrO2–2 mol% RE2O3 (RE = La, Pr, Nd, Sm, Gd and Dy) spun ...

'Fit or unfit': theorie en praktijk van re-integratie

NARCIS (Netherlands)

Sol, C.C.A.M.; Kok, K.

2014-01-01

If the objective of creating a labour market with opportunity for unemployed is to be achieved through re-employment programmes, understanding the mechanisms and conditions at work is essential. Following ‘Realistic Evaluation’ the authors focus on theories in use behind re-employment programmes by

XPS investigations of tribolayers formed on TiN and (Ti,Re)N coatings

Energy Technology Data Exchange (ETDEWEB)

Oktay, Serkan; Kahraman, Zafer; Urgen, Mustafa; Kazmanli, Kursat, E-mail: kursat@itu.edu.tr

2015-02-15

Graphical abstract: - Highlights: • The (Ti,Re)N coating (8 ± 1.9 at.% Re) consisted of TiN and ReNx (x > 1.33) phases. • TiO{sub 2} provided low friction coefficient to TiN coating at 150 °C. • Re addition to TiN drastically dropped the friction coefficients to 0.17–0.22. • Re{sub 2}O{sub 7} provided very low friction coefficient to (Ti,Re)N coating. • Re addition to TiN improved the wear behavior. - Abstract: TiN and (Ti,Re)N coatings were deposited on high-speed-steel substrates by a hybrid coating system composed of cathodic arc PVD and magnetron sputtering techniques. In order to keep rhenium content low (8 ± 1.9 at.%) in the coating, magnetron sputtering technique was utilized to evaporate rhenium. The (Ti,Re)N coating consisted of TiN and ReN{sub x} (x > 1.33) phases. The hardness of TiN and (Ti,Re)N were 31 GPa and 29 GPa ( ± 2 GPa), respectively. Tribological behaviors of the samples were tested against Al{sub 2}O{sub 3} balls at 21 °C (RT) and 150 °C (HT) by reciprocating wear technique. The tribolayers were analyzed by XPS technique. Friction coefficients of TiN were 0.56, 0.35 for 21 °C and 150 °C tests, respectively. Rhenium addition to TiN drastically dropped the friction coefficients to 0.22 and 0.17 for RT and HT samples. Rhenium addition also improved the wear resistance of the coating at both test temperatures. For TiN, main oxide component of the tribolayers was Ti{sub 2}O{sub 3} for RT tests and TiO{sub 2} for HT tests. The oxide layer formed on (Ti,Re)N were the mixture of TiO{sub 2}, Ti−O−N, ReO{sub 2} and Re{sub 2}O{sub 7} for both test temperatures. Re{sub 2}O{sub 7} provided very low friction coefficient to (Ti,Re)N. The findings are consistent with the crystal chemistry approach.

RE-SONANCE--IJu-ne

Indian Academy of Sciences (India)

this title. The chapter on physics and experi- mental methods is perhaps the weakest and might have been better left out or re-written from a perspective that better serves the title and the aims of the rest of the book. There are problems with the proof reading e.g., titanium nitride described as TiC, phrases in sentences.

[Study on mercury re-emissions during fly ash utilization].

Science.gov (United States)

Meng, Yang; Wang, Shu-Xiao

2012-09-01

The amount of fly ash produced during coal combustion is around 400 million tons per year in China. About 65%-68% of fly ash is used in building material production, road construction, architecture and agriculture. Some of these utilization processes include high temperature procedures, which may lead to mercury re-emissions. In this study, experiments were designed to simulate the key process in cement production and steam-cured brick production. A temperature programmed desorption (TPD) method was used to study the mercury transformation in the major utilization processes. Mercury re-emission during the fly ash utilization in China was estimated based on the experimental results. It was found that mercury existed as HgCl2 (Hg2 Cl2), HgS and HgO in the fly ash. During the cement production process, more than 98% of the mercury in fly ash was re-emitted. In the steam-curing brick manufacturing process, the average mercury re-emission percentage was about 28%, which was dominated by the percentage of HgCl2 (Hg2 Cl2). It is estimated that the mercury re-emission during the fly ash utilization have increased from 4.07 t in 2002 to 9.18 t in 2008, of which cement industry contributes about 96.6%.

Pelvic re-irradiation using stereotactic ablative radiotherapy (SABR): A systematic review.

Science.gov (United States)

Murray, Louise Janet; Lilley, John; Hawkins, Maria A; Henry, Ann M; Dickinson, Peter; Sebag-Montefiore, David

2017-11-01

To perform a systematic review regarding the use of stereotactic ablative radiotherapy (SABR) for the re-irradiation of recurrent malignant disease within the pelvis, to guide the clinical implementation of this technique. A systematic search strategy was adopted using the MEDLINE, EMBASE and Cochrane Library databases. 195 articles were identified, of which 17 were appropriate for inclusion. Studies were small and data largely retrospective. In total, 205 patients are reported to have received pelvic SABR re-irradiation. Dose and fractionation schedules and re-irradiated volumes are highly variable. Little information is provided regarding organ at risk constraints adopted in the re-irradiation setting. Treatment appears well-tolerated overall, with nine grade 3 and six grade 4 toxicities amongst thirteen re-irradiated patients. Local control at one year ranged from 51% to 100%. Symptomatic improvements were also noted. For previously irradiated patients with recurrent pelvic disease, SABR re-irradiation could be a feasible intervention for those who otherwise have limited options. Evidence to support this technique is limited but shows initial promise. Based on the available literature, suggestions for a more formal SABR re-irradiation pathway are proposed. Prospective studies and a multidisciplinary approach are required to optimise future treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

An Exploratory Study on the Re-finding Behavior on the Web

Directory of Open Access Journals (Sweden)

Hsiao-Tieh Pu

2010-06-01

Full Text Available It is common for users to relocate information previously found on the web. However, their search behaviors in initial finding and the subsequent re-finding may differ due to the dynamic nature and contextual diversity of the web. This study used experiment, observation, interview, and questionnaires to investigate the characteristics of re-finding behavior and compare users’ performance in finding and re-finding. Though not significantly different, the study participants used more search tools, combined various strategies to obtain contextual clues of finding process, utilized more complex search tactics, and had more interactions with search engines used. Findings also show that participants spent less time in re-finding than in finding, yet the cognitive loading and difficulties increased in re-finding. Participants were satisfied with the results obtained in re-finding, but they also claimed that the search performance would be better if the system offered more functions to support recall of previous search results. Participants’ satisfaction with search performance also varied by task type. Based on the findings, this study recommends that re-finding efficiency may be improved by enhancing recall functionalities in browsers and by using personal information management tools. [Article content in Chinese; Extended abstract in English

Studies of Metal-Metal Bonded Compounds in Catalysis

Energy Technology Data Exchange (ETDEWEB)

Berry, John F. [Univ. of Wisconsin, Madison, WI (United States)

2018-01-19

The overall goals of this research are (1) to define the fundamental coordination chemistry underlying successful catalytic transformations promoted by metal-metal bonded compounds, and (2) to explore new chemical transformations that occur at metal-metal bonded sites that could lead to the discovery of new catalytic processes. Transformations of interest include metal-promoted reactions of carbene, nitrene, or nitrido species to yield products with new C–C and C–N bonds, respectively. The most promising suite of transition metal catalysts for these transformations is the set of metal-metal bonded coordination compounds of Ru and Rh of the general formula M₂(ligand)₄, where M = Ru or Rh and ligand = a monoanionic, bridging ligand such as acetate. Development of new catalysts and improvement of catalytic conditions have been stymied by a general lack of knowledge about the nature of highly reactive intermediates in these reactions, the knowledge that is to be supplied by this work. Our three specific objectives for this year have been (A) to trap, isolate, and characterize new reactive intermediates of general relevance to catalysis, (B) to explore the electronic structure and reactivity of these unusual species, and how these two properties are interrelated, and (C) to use our obtained mechanistic knowledge to design new catalysts with a focus on Earth-abundant first-row transition metal compounds.

Synthesis and photoluminescence properties of microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors

Energy Technology Data Exchange (ETDEWEB)

Dabre, K.V. [Department of Physics, Arts, Commerce and Science College, Koradi, Nagpur 441111 (India); Park, K. [Faculty of Nanotechnology and Advanced Materials Engineering, Sejong University, Seoul 143-747 (Korea, Republic of); Dhoble, S.J., E-mail: sjdhoble@rediffmail.com [Department of Physics, R.T.M. Nagpur University, Nagpur 440033 (India)

2014-12-25

Graphical abstract: CIE chromaticity coordinate diagram (1931) indicating different colors of Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu (a), Dy (b and c), Sm (d–f) and Pr (g and h)) phosphor under different excitation 466 nm (a), 312 nm (b), 454 nm (c), 313 nm (d), 408 nm (e), 482 nm (f), 315 nm (g) and 450 nm (h). - Highlights: • Microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors were synthesized by solid state method. • Photoluminescence properties of phosphor were investigated. • Color of the phosphor for different excitation has been verified by chromaticity diagram. • The host absorption and energy transfer were investigated. - Abstract: The novel microcrystalline Sr{sub 2}ZnWO{sub 6}:RE{sup 3+} (RE = Eu, Dy, Sm and Pr) phosphors were synthesized by solid-state reaction method at 1250 °C and their photoluminescence properties were investigated. The Eu{sup 3+} and Dy{sup 3+} activated phosphors show intense red (616 nm) and yellow (574 nm) emission respectively; which indicate that the rare earth ions are substituted at non-centrosymmetric site in the host lattice. Near white (Dy{sup 3+}) and reddish-orange (Sm{sup 3+}) emissions of rare earth ions in the host lattice show strong host absorption and energy transfer from the host to activator ion. Pr{sup 3+} activated phosphor shows a series of emission peaks in the visible region with the most intense peak in the blue region at 491 and 499 nm.

Thermochemical Properties of the Complexes RE(HSal)3·2H2O (RE=La, Ce, Pr, Nd, Sm)

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

Five solid rare earth salicylate complexes were synthesized by low hydrated lathanide chloride and salicylic acid. The complexes in this experiment were identified as the general formula RE(Hsal)3·2H2O(RE=La, Ce, Pr, Nd, Sm) by elemental analysis and EDTA volumetric analysis. IR spectra of the complexes show that carboxyl of salicylic acid coordinates to RE3+ ions. Electrochemical behaviors of the complexes on the glass-carbon electrode were researched with cyclic voltammetry (CV). It is indicated that the electrochemical process of the complexes is a one-electron redox process and the electrochemical reversibility of complexes is less than that of the lanthanide chlorides. The constant-volume combustion energies of complexes, ΔcU, were determined with a precise rotating-bomb calorimeter at 298.15 K. Their standard molar enthalpies of combustion, ΔcHθm, and standard molar enthalpies of formation, ΔfHθm, were calculated.

Telling Parents You're Pregnant

Science.gov (United States)

... Putting your feelings into words takes plenty of maturity and it's not easy to do. Don't worry if the words don't come out perfectly or if you cry or get emotional as you're saying them. It can help ...

Tc and Re Behavior in Borosilicate Waste Glass Vapor Hydration Tests

International Nuclear Information System (INIS)

McKeown, David A.; Buechele, Andrew C.; Pegg, Ian L.; Lukens, Wayne W.; Shuh, David K.

2007-01-01

Technetium (Tc), found in some nuclear wastes, is of particular concern with regard to long-term storage, because of its long-lived radioactivity and high mobility in the environment. Tc and rhenium (Re), commonly used as a non-radioactive surrogate for Tc, were studied to assess their behavior in borosilicate glass under hydrothermal conditions in the Vapor Hydration Test (VHT). X-ray absorption spectroscopy (XAS) and scanning electron microscopy (SEM) measurements were made on the original Tc- and Re-containing glasses and their corresponding VHT samples, and show different behavior for Tc and Re under VHT conditions. XAS indicates that, despite starting with different Tc(IV) and Tc(VII) distributions in each glass, the VHT samples have 100% Tc(IV)O 6 environments. SEM shows complete alteration of the original glass, Tc enrichment near the sample surface, and Tc depletion in the center. Perrhenate (Re(VII)O 4 - ) is dominant in both Re-containing samples before and after the VHT, where Re is depleted near the VHT sample surface and more concentrated toward the center. (authors)

Enhancement of CdSiO3: Tb3+ green long-lasting phosphors by co-doping with Re3+ (Re3+=Gd3+, Y3+, La3+) ions

International Nuclear Information System (INIS)

Zeng, Wei; Wang, Yuhua; Han, Shaochun; Chen, Wenbo; Li, Gen

2014-01-01

CdSiO 3 : Tb 3+ , Re 3+ long-lasting phosphors were synthesized by the conventional high temperature solid-state method. A green-light phosphorescence phenomenon, which was associated with the 5 D 4 → 7 F J (J=6, 5, 4, 3) transitions of the Tb 3+ ion, was observed. Introduction of Re 3+ (Re 3+ =Gd 3+ , Y 3+ , La 3+ ) ions, which deepens the depth (E t ) or/and increases the density (n 0 ) of traps, greatly improved the afterglow properties of CdSiO 3 : Tb 3+ . Possible mechanism of CdSiO 3 : Tb 3+ , Re 3+ was discussed in this work. - Highlights: • CdSiO 3 : Tb 3+ , Re 3+ samples enrich the color of long-lasting afterglow phosphors in CdSiO 3 host. • Both the afterglow intensity and the lasting time are greatly enhanced for the co-doped samples, especially for Cd 0.96 SiO 3 : Tb 0.03 3+ , La 0.01 3+ . • Introduction of Re 3+ (Re 3+ =Gd 3+ , Y 3+ , La 3+ ) ions, which deepens the depth (E t ) or increase density(n 0 ) of traps, greatly improved the afterglow properties of CdSiO 3 : Tb 3+

Film grain synthesis and its application to re-graining

Science.gov (United States)

Schallauer, Peter; Mörzinger, Roland

2006-01-01

Digital film restoration and special effects compositing require more and more automatic procedures for movie regraining. Missing or inhomogeneous grain decreases perceived quality. For the purpose of grain synthesis an existing texture synthesis algorithm has been evaluated and optimized. We show that this algorithm can produce synthetic grain which is perceptually similar to a given grain template, which has high spatial and temporal variation and which can be applied to multi-spectral images. Furthermore a re-grain application framework is proposed, which synthesises based on an input grain template artificial grain and composites this together with the original image content. Due to its modular approach this framework supports manual as well as automatic re-graining applications. Two example applications are presented, one for re-graining an entire movie and one for fully automatic re-graining of image regions produced by restoration algorithms. Low computational cost of the proposed algorithms allows application in industrial grade software.

Evaluation method of iodine re-evolution from an in-containment water pool after a loss of coolant accident, Part II: Evaluation of pH and iodine re-evolution

International Nuclear Information System (INIS)

Kim, Tae Hyeon; Jeong, Ji Hwan

2016-01-01

Highlights: • It is required to evaluate re-evolved iodine from sump water after LOCA. • Transport of iodine and chemicals influencing pH were analyzed using CFD. • Chemical conditions of the iodine-rich region suppress iodine re-evolution. • The current evaluation method for I 2 re-evolution is excessively conservative. - Abstract: Radioactive iodine that is released during a postulated loss of coolant accident is dissolved into the containment spray water and transported into the in-containment refueling water storage tank (IRWST). The re-evolution of iodine from the water is a safety concern. In this study, three-dimensional computational fluid dynamics (CFD) analyses are conducted in order to analyze the transport of chemical species including iodine in the IRWST and to calculate the amount of iodine that re-evolves from the IRWST water. The CFD analyses demonstrate that the pH of water is high where the iodine concentration is high. Considering that the creation rate of molecular iodine declines as the pH increases, it can be understood that the iodine re-evolution is not so strong in practical situations because the chemical conditions of the iodine-rich region suppress the re-evolution of the iodine. In addition, four different methods for evaluating the amount of re-evolved iodine are examined. The amount of re-evolved iodine calculated using the total-volume-average values, which are currently used for safety analyses, appear to be significantly higher than those determined using other methods. The amount of re-evolved iodine estimated using a realistic method with a conservative assumption of volatilization appears to be approximately one thousandth of that evaluated using the current method. This implies that the current method is very conservative.

A novel steel RE-borosulphurizing and mechanical properties of the produced RE-borosulfide layer

Science.gov (United States)

Wang, Dong; Li, Yun-dong; Zhang, Xiu-li

2013-07-01

In this study, 45# carbon steels were boronized, borosulphurized and RE-borosulphurized at 950 °C for 6 h, respectively. The samples were then characterized by scanning electron microscopy, X-ray diffraction, Auger electron spectroscopy, microhardness tester and ring-on-block wear tester. It has shown that the diffusion front (the interface between the diffusion layer and the substrate) of the boride layer (BL) and the boro-sulfide layer (BSL) is saw tooth shape, while the diffusion front of the RE-boro-sulfide layer (RBSL) is flat. Compared with BSL layer, RBSL layer has a smaller and more uniform grain size, and a flatter hardness gradient from the surface to the diffusion front. The RBSL layer, consisting of an outer layer (from surface to 30 μm) mainly composed of Fe-B and an inner layer (from 30 μm to the diffusion front) mainly composed of Fe-S, has the best wear resistance and the most sufficient adhesion among those three.

Mid-temperature deep removal of hydrogen sulfide on rare earth (RE = Ce, La, Sm, Gd) doped ZnO supported on KIT-6: Effect of RE dopants and interaction between active phase and support matrix

Science.gov (United States)

Li, Lu; Zhou, Pin; Zhang, Hongbo; Meng, Xianglong; Li, Juexiu; Sun, Tonghua

2017-06-01

Rare earth oxides (RE = Ce, La, Sm and Gd) doped ZnO supported on KIT-6 sorbents (RE-ZnO/KIT-6) were synthesized by sol-gel method and their performance for deep removal of H2S (bellow 0.1 ppmv) from gas stream at medium temperature was tested. The RE dopants (except Ce) significantly enhance the deep desulfurization capacity of ZnO/KIT-6 sorbent and maintained higher sulfur uptake capacities upon multiple cycles of regeneration by a simple thermal oxidation in 10 v% of O2 in N2 atmosphere. The results of SAXS, XRD, N2 physisorption, TEM, FIIR, and XPS implied that the KIT-6 structure of loading metal oxides remained intact. It was found that RE could hinder the ZnO crystal ripening during calcination resulted in smaller ZnO particles, enhance the interaction of ZnO and silica matrix to improve the dispersion of active phase on KIT-6. Furthermore, by increasing the outlayer electron density of Zn atom and oxygen transfer ability, the synergistic effect considered to be favorable for RE-ZnO/KIT-6 sulfidation. Even though the performance of improving ZnO dispersion was weaker than that of Sm and Gd, La-ZnO/KIT-6 performs the best deep desulfurizers by changing the surface chemical atmosphere for ZnO. Steam in the gas stream inhibited the capture of H2S by ZnO in the sorbents, in the case of La-ZnO/KIT-6, the steam content should control as lower as 5 v% to ensure the desulfurization efficiency and precision.

Re-irradiation of the human spinal cord

International Nuclear Information System (INIS)

Sminia, P.; Oldenburger, F.; Hulshof, M.C.C.M.; Slotman, B.J.; Schneider, J.J.

2002-01-01

Purpose: Experimental animal data give evidence of long-term recovery of the spinal cord after irradiation. By extrapolation of these data, re-irradiation regimes were designed for eight patients who required palliative radiotherapy. As a consequence of reirradiation, their spinal cords were exposed to cumulative doses exceeding the tolerance dose. Radiobiological and clinical data are presented. Patients and method: Eight patients were re-irradiated on the cervical (n=1), thoracic (n=5) and lumbar (n=2) spinal cord. The time interval between the initial and re-treatment ranged from 4 months to 12.7 years (median: 2.5 years). (Re-)treatment schemes were designed and analyzed on basis of the biologically effective dose (BED) according to the linear-quadratic model. The repair capacity (α/β ratio) for the cervico-thoracic and lumbar spinal cord was assumed to be 2 Gy and 4 Gy, with a BED tolerance of 100 Gy and 84 Gy, respectively. Results: The cumulative irradiation dose applied to the spinal cord varied between 125 and 172% of the BED tolerance . During follow-up, ranging from 33 days to >4.5 years (median: 370 days) none of the patients developed neurological complications. Seven patients died from tumor progression, and one patient is still alive. Conclusion: Long-term recovery of the spinal cord from radiation injury, which has been demonstrated in rodents and primates, may also occur in humans. (orig.) [de

Mid-temperature deep removal of hydrogen sulfide on rare earth (RE = Ce, La, Sm, Gd) doped ZnO supported on KIT-6: Effect of RE dopants and interaction between active phase and support matrix

Energy Technology Data Exchange (ETDEWEB)

Li, Lu; Zhou, Pin; Zhang, Hongbo; Meng, Xianglong; Li, Juexiu; Sun, Tonghua, E-mail: sunth@sjtu.edu.cn

2017-06-15

Highlights: • Various rare earth (RE)-doped ZnO/KIT-6 sorbents were prepared via sol-gel method. • La showed the highest efficiency on promoting ZnO/KIT-6 desulfurization activity. • The morphology of ZnO on KIT-6 played a crucial role for the reactivity. • The most initial factor of improving reactivity by RE was surface chemical property. • Crystallinity, host-guest interaction were also important to ZnO state on support. - Abstract: Rare earth oxides (RE = Ce, La, Sm and Gd) doped ZnO supported on KIT-6 sorbents (RE-ZnO/KIT-6) were synthesized by sol-gel method and their performance for deep removal of H{sub 2}S (bellow 0.1 ppmv) from gas stream at medium temperature was tested. The RE dopants (except Ce) significantly enhance the deep desulfurization capacity of ZnO/KIT-6 sorbent and maintained higher sulfur uptake capacities upon multiple cycles of regeneration by a simple thermal oxidation in 10 v% of O{sub 2} in N{sub 2} atmosphere. The results of SAXS, XRD, N{sub 2} physisorption, TEM, FIIR, and XPS implied that the KIT-6 structure of loading metal oxides remained intact. It was found that RE could hinder the ZnO crystal ripening during calcination resulted in smaller ZnO particles, enhance the interaction of ZnO and silica matrix to improve the dispersion of active phase on KIT-6. Furthermore, by increasing the outlayer electron density of Zn atom and oxygen transfer ability, the synergistic effect considered to be favorable for RE-ZnO/KIT-6 sulfidation. Even though the performance of improving ZnO dispersion was weaker than that of Sm and Gd, La-ZnO/KIT-6 performs the best deep desulfurizers by changing the surface chemical atmosphere for ZnO. Steam in the gas stream inhibited the capture of H{sub 2}S by ZnO in the sorbents, in the case of La-ZnO/KIT-6, the steam content should control as lower as 5 v% to ensure the desulfurization efficiency and precision.

Together and apart: a typology of re-partnering in old age.

Science.gov (United States)

Koren, Chaya

2014-08-01

The human need for love, friendship, and physical contact, and the fear of loneliness do not diminish with age. Widowhood and late-life divorce and increased life expectancy are likely to lead to alternative relationships, such as re-partnering. The purpose of this paper is to explore interplays between emotional and physical components of re-partnering in old age. Theoretical sampling of 20 couples included men who re-partnered at the age of 65+ years and women at the age of 60+ years, following termination of lifelong marriages due to death or divorce. Living arrangements included married or unmarried cohabitation under the same roof or in separate homes. Forty semi-structured interviews were tape-recorded and transcribed verbatim. The couple was the unit of analysis. Interplays between physical and emotional dimensions were examined using five abductive parameters derived from data analysis resulting in a fourfold typology of emotional and physical closeness/distance in re-partnering in old age: (1) living together (physically and emotionally); (2) living apart (physically) together (emotionally); (3) living together (physically) apart (emotionally); and (4) living apart (physically and emotionally). Findings revealed types of partner relationships that are different from lifelong marriages. The typology could help professionals working with older persons regarding what to expect in re-partnering in old age and be included in developmental theories as an option in old age. A quantitative tool for research and therapy purposes, entitled The Re-partnering in Old Age Typology Scale (RPOAT Scale), based on abductive parameters, could be established for measuring re-partnering relationship quality and classifying re-partnering couples.

Disposal and re-use of TENORM - legal limitations and obstacles

International Nuclear Information System (INIS)

Weiss, D.; Ettenhuber, E.

2004-01-01

While implementing EURATOM guideline 96/29 in the German legislation, in June of 2001 an essential pre-condition was created for re-use or disposal of TENORM. An essential progress has been achieved allowing to re-use TENORM or to dump it together with other residues and waste, if the specific activity does not exceed the limits defined in the radiation protection ordinance (StrlSchV). Otherwise, if the specified limits in terms of concentration or radiation dose are exceeded, than these materials must remain under radiological protection. A practical application of the new German regulation turns out to be difficult especially for disposal together with other waste and for re-use as backfilling material in mines taking into account problems arising from adaptation of the respective legislation on radiation protection, soil protection, waste management and shipment of dangerous goods. The report tackles obstacles for re-use and disposal of TENORM together with garbage and toxic waste arising from the new legislation. Otherwise, proposals will be given how obstacles of selected options for re-use and disposal can be overcome. (orig.)

Prostate needle biopsies: interobserver variation and clinical consequences of histopathological re-evaluation

DEFF Research Database (Denmark)

Berg, Kasper Drimer; Toft, Birgitte Grønkaer; Røder, Martin Andreas

2011-01-01

Histopathological grading of prostate cancer (PCa) is associated with significant interobserver variability. This, as well as clinical consequences of histopathological re-evaluation, was investigated. In 350 patients, histopathological re-evaluations of prostate biopsies were compared with primary...... pathology reports and with histopathology of the radical prostatectomy specimen. The consequences of re-evaluation for clinical workup and treatment of patients according to local algorithms were determined. For Gleason score (GS), complete agreement between primary report and re-evaluation was found in 76.......9%. The cancers were assessed with higher GS at re-evaluation in 25.0% of patients in cases with primary GS = 6, while scores were devaluated in 3.0% and 10.3% of the patients with primary GS = 7 and = 8, respectively. Strategies for clinical evaluation and treatment were changed as a result of the biopsy re...

The Secret of Guided Missile Re-Entry,

Science.gov (United States)

1986-06-25

I RD-PAI169 598 THE SECRET OF GUIDED MISSILE RE-ENTRY(U) FOREIGN / I TECHNOLOGY DIV NRIGHT-PATTERSON RFB OH J CHEN ET AL. I 25 JUN 96 FTD-ID(RS)T...TECHNOLOGY DIVISION THE SECRET OF GUIDED MISSILE RE-ENTRY by Chen Jingzhong, An Sehua J L 0 7 ’:;85’ ’ 0 *Approved for public release; Distribution...unlimite t d. :. 86 7 034.. FTD- ID(RS)T-0459-86 HUMAN TRANSLATION FTD-ID(RS)T-0459-86 25 June 1986 MICROFICHE NR: F - - 0Q 9? THE SECRET OF GUIDED

Lad os lære af nutidens private ledere - ikke fortidens

DEFF Research Database (Denmark)

Torfing, Jacob

2017-01-01

Hvis vi endelig skal lære af den private sektor en gang til, så lad os dog lære af de bedste i klassen i stedet for at kigge i bakspejlet og genopfinde ledelsestænkning fra 60’erne og 70’erne, skriver professor Jacob Torfing.......Hvis vi endelig skal lære af den private sektor en gang til, så lad os dog lære af de bedste i klassen i stedet for at kigge i bakspejlet og genopfinde ledelsestænkning fra 60’erne og 70’erne, skriver professor Jacob Torfing....

Re-excision of margins before breast radiation-diagnostic or therapeutic?

International Nuclear Information System (INIS)

Chism, Derek B.; Freedman, Gary M.; Li, Tianyu; Anderson, Penny R.

2006-01-01

Purpose: To identify factors in breast cancer patients that predict the pathologic results of re-excision for close or positive margins and to determine the effect on local control. Methods and Materials: We divided 1,044 patients with Stage I-II breast cancer with a close (≤2 mm) or positive margin after initial excision into three groups. Group 1 included 199 patients without additional excision, Group 2 included 546 patients with re-excision found to be free of cancer, and Group 3 included 299 patients with re-excision and residual cancer. All patients were treated with radiotherapy with a median follow-up of 6.7 years. Results: The 10-year local control rate was 95% for Group 1 and 94% for Groups 2 and 3 (p = 0.788). Of the 846 patients, 65% had no residual disease on re-excision and 35% did have residual tumor. The factors significantly associated with positive re-excision findings were initial positive margins, positive nodes, Stage T2 tumor, and an extensive intraductal component. The 10-year local control rate was 95% for Group 2 vs. 91% for Group 3 (p = 0.038). Conclusion: The low recurrence rates seen in this study suggest that selected patients with non-negative margins, particularly those with a low risk of having residual disease at re-excision, may be treated with radiotherapy

Developing the 186 Re radiolabelling procedures of peptides and monoclonal antibodies

International Nuclear Information System (INIS)

Lungu, V.; Mihailescu, G.

1999-01-01

Mono and poli-clonal antibodies are the most recent candidate molecules for the radiopharmaceutical preparation used in radioimmunotherapy and radiodiagnostic. Our study presents results in 186 Re direct labelling of HIgG (Human Immunoglobulin G) poli-clonal antibody. The steps in labelling process are: 1. pre-reduction -S-S- bridges of HIgG molecule with ascorbic acid in pH = 3.5 - 4.5; 2. preparation of the reducing system for 186 ReO 4 - in presence of Sn 2+ ions excess and 3. coupling 186 Re (red) to -SH groups of biomolecules. The specific reactions of each step above are controlled by: incubation time and temperature, pH, molar ratio 186 Re: HIgG. 186 Re-HIgG samples were purified by gel elution chromatography method and the quality control was performed by chromatography techniques. To labelled of HIgG we effected the pre-reduction of -S-S- bridges of biomolecules to sulfhydryls using the following reducing agents: ascorbic acid, cysteine, active hydrogen, 2,3 dimercaptopropanol. The pre-reduction reactions are controlled by mass ratios of reduction agent/biomolecule, pH, temperature and time of incubation. HIgG was the biomolecule used in the pre-reduction reactions. The specific parameters for each systems are presented. The stannous chloride was used as reducing agent in two systems, SnCl 2 : 0.05 N HCl and SnCl 2 : 20 mg/ml citric acid. The coupling reaction of 186 Re (red) with the biomolecule has been controlled by time and incubation temperature and the influence of pH regarding the binding of 186 Re to the biomolecule. 186 Re-HIgG was obtained by: i) incubation at the room temperature, 1 hour time of HIgG in thiol form and 186 Re in reducing form and ii) incubation of HIgG in thiol form, at 37 deg C and 22 hours time, with adding after pre-reduction of SnCl 2 and Na 186 ReO 4 . Quality control was effected by chromatography techniques (paper and gel chromatography) on labelled biomolecule before and after purification. The elution gel chromatography

Re-Assessment of Concrete Bridges

DEFF Research Database (Denmark)

Thoft-Christensen, Palle

In this paper two aspects of re-assessment of the reliability of concrete bridges are discussed namely modelling of the corrosion of reinforcement and updating of uncertain variables. The main reason for deterioration of concrete bridges is corrosion of the reinforcement. Therefore, modelling...

Re-Architecture: Reality or Utopia?

NARCIS (Netherlands)

Pereira-Roders, A.R.; Post, J.M.; Erkelens, P.A.

2008-01-01

RE-ARCHITECTURE: lifespan rehabilitation of built heritage (2004-2007) is a doctoral research funded by the Foundation for Science and Technology, Portugal; and hosted by the Unit Architectural Design and Engineering, Eindhoven University of Technology, The Netherlands. This doctoral research is now

Preparation and quality control of 186Re compounds

International Nuclear Information System (INIS)

Noto, M.G.; Amor, R.A.; Caviglia, D.A.; Ratner, M.T.; Schroder, A.M.; Rocco, J.C.; Mancini, A.C.

1987-01-01

The optimal conditions were investigated in order to label the methylendiphosphonate (MDP), hydroxyethylendiphosphonate (HEDP), pyrophosphonate (PYP) and ethylendiaminotetramethylenphosphoric (EDTMP) with 186 Re. The biodistribution of these compounds in experimental animals were studied to determine the most suitable therapeutic agent for its eventual use as pain palliative in patients with bone metastases. The biodistribution assays were performed in Wistar rats, and the 186 Re HEDP was finally chosen. (M.E.L.) [es

Re-humanising Public Urban Space

DEFF Research Database (Denmark)

Almahmood, Mohammed Abdulrahman M

, this thesis suggests that re-humanising public urban space should not only be considered as a matter of design, but also as an on-going process which includes an inclusive spatial planning agenda and the management of space supplemented by background knowledge regarding the culture of use of space.......This PhD thesis aims to contribute to a better understanding of the spatial, social, and cultural dimensions of the formation of human-centred public urban space. ‘Re-humanising’ the city is a traveling concept which implies that public urban spaces are liveable, walkable, safe, enjoyable......, and inclusive thereby allowing vibrant social interaction. While the inclusiveness of space is considered as a core value in human-centred public urban space, social and spatial exclusion is a key challenge to the success of public urban space, especially in the Global South. The mainstream research in urban...

7 CFR 1710.104 - Service to non-RE Act beneficiaries.

Science.gov (United States)

2010-01-01

... GUARANTEES Loan Purposes and Basic Policies § 1710.104 Service to non-RE Act beneficiaries. (a) To the... made to finance electric facilities to serve consumers that are not RE Act beneficiaries. (b) Loan...

Toxoplasma gondii: A study of oocyst re-shedding in domestic cats.

Science.gov (United States)

Zulpo, Dauton Luiz; Sammi, Ana Sue; Dos Santos, Joeleni Rosa; Sasse, João Pedro; Martins, Thais Agostinho; Minutti, Ana Flávia; Cardim, Sérgio Tosi; de Barros, Luiz Daniel; Navarro, Italmar Teodorico; Garcia, João Luis

2018-01-15

The aim of the present study was to evaluate the re-shedding of T. gondii oocysts in cats fed tissue cysts of homologous and heterologous strains 12, 24 and 36 months after the first infection. Thirteen cats were used in the present study and were divided into four groups: G1 (n=2), G2 (n=3), G3 (n=5), and G4 (n=3). G1, G3 and G4 cats were infected with brain cysts of ME49 and G2 with TgDoveBr8, both genotype II strains of T. gondii. The G1 and G2 cats were re-infected after twelve months with brain cysts of VEG strain (genotype III), and G3 cats were re-infected with TgDoveBr1 (genotype II). The G3 cats were re-infected a third time after 24 months from the second infection, and the G4 cats were re-infected 36 months after the initial infection with cysts of the VEG strain. The cats' feces were evaluated using fecal flotation and genotyped with PCR-RFLP. The serological responses for IgM, IgA and IgG were determined by ELISA. All cats shed oocysts after the initial infection. Only one G1 cat shed oocysts when re-infected after twelve months with the VEG strain. No G2 cats excreted oocysts after the second infection with VEG. G3 cats, when re-infected after twelve months with the TgDoveBr1 strain, did not shed oocysts. However, when challenged after a third time with the VEG strain, three out of four cats shed oocysts. In the G4 group, when re-infected after thirty-six months with the VEG strain, two out of three cats shed oocysts. All oocyst samples were genotyped and characterized as the same genotype from the inoculum. Protection against oocyst re-excretion occurred in 90%, 25%, and 33.4% of cats after 12, 24, and 36 months from the initial infection, respectively. Therefore, the environmental contamination by oocysts from re-infected adult cats is only 30% lower than from kittens. In conclusion, the excretion of T. gondii oocysts was higher in experimentally re-infected cats throughout the years, especially when a heterologous strain was used. Copyright © 2017

A Study on Re-entry Predictions of Uncontrolled Space Objects for Space Situational Awareness

Science.gov (United States)

Choi, Eun-Jung; Cho, Sungki; Lee, Deok-Jin; Kim, Siwoo; Jo, Jung Hyun

2017-12-01

The key risk analysis technologies for the re-entry of space objects into Earth’s atmosphere are divided into four categories: cataloguing and databases of the re-entry of space objects, lifetime and re-entry trajectory predictions, break-up models after re-entry and multiple debris distribution predictions, and ground impact probability models. In this study, we focused on re- entry prediction, including orbital lifetime assessments, for space situational awareness systems. Re-entry predictions are very difficult and are affected by various sources of uncertainty. In particular, during uncontrolled re-entry, large spacecraft may break into several pieces of debris, and the surviving fragments can be a significant hazard for persons and properties on the ground. In recent years, specific methods and procedures have been developed to provide clear information for predicting and analyzing the re-entry of space objects and for ground-risk assessments. Representative tools include object reentry survival analysis tool (ORSAT) and debris assessment software (DAS) developed by National Aeronautics and Space Administration (NASA), spacecraft atmospheric re-entry and aerothermal break-up (SCARAB) and debris risk assessment and mitigation analysis (DRAMA) developed by European Space Agency (ESA), and semi-analytic tool for end of life analysis (STELA) developed by Centre National d’Etudes Spatiales (CNES). In this study, various surveys of existing re-entry space objects are reviewed, and an efficient re-entry prediction technique is suggested based on STELA, the life-cycle analysis tool for satellites, and DRAMA, a re-entry analysis tool. To verify the proposed method, the re-entry of the Tiangong-1 Space Lab, which is expected to re-enter Earth’s atmosphere shortly, was simulated. Eventually, these results will provide a basis for space situational awareness risk analyses of the re-entry of space objects.

Re-Condensation and Liquefaction of Helium and Hydrogen Using Coolers

International Nuclear Information System (INIS)

Green, Michael A.

2009-01-01

Coolers are used to cool cryogen free devices at temperatures from 5 to 30 K. Cryogen free cooling involves a temperature drop within the device being cooled and between the device and the cooler cold heads. Liquid cooling with a liquid cryogen distributed over the surface of a device combined with re-condensation can result in a much lower temperature drop between the cooler and the device being cooled. The next logical step beyond simple re-condensation is using a cooler to liquefy the liquid cryogen in the device. A number of tests of helium liquefaction and re-condensation of helium have been run using a pulse tube cooler in the drop-in mode. This report discusses the parameter space over which re-condensation and liquefaction for helium and hydrogen can occur.

Outcome after re-irradiation of head and neck cancer patients

Energy Technology Data Exchange (ETDEWEB)

Platteaux, Nele; Dirix, Piet; Vanstraelen, Bianca; Nuyts, Sandra [University Hospitals Leuven, Campus Gasthuisberg (Belgium). Dept. of Radiation Oncology

2011-01-15

Purpose: To retrospectively report the outcome of head and neck cancer patients following re-irradiation. Patients and Methods: A total of 51 patients with recurrent or second primary head and neck cancer received re-irradiation at Leuven University Hospital. Survival and locoregional control were calculated. Doses to organs at risk were retrieved from dose-volume histograms. Radiation-related toxicities were reported. Results: The 2-year actuarial overall survival rate was 30%. On univariate analysis, surgery before re-irradiation and high radiation dose were associated with superior survival. Grade 3 acute and grade 3 or more late toxicity occurred in respectively 29.4% and 35.3% of the patients. Conclusion: Re-irradiation in head and neck cancer patients is feasible with acceptable late toxicity, although the survival remains poor. (orig.)

Les orfèvres de la lumière

CERN Document Server

Gacoin, Marie-Pauline

2010-01-01

Le synchrotron SOLEIL est un accélérateur de particules d environ 200 mètres de diamètre, utilisé... comme une lampe. Un faisceau d électrons, fin comme un cheveu mais très énergétique, y circule quasiment à la vitesse de la lumière, émettant ce que l on appelle un rayonnement synchrotron (car le maintien des électrons sur la même trajectoire est obtenu au prix d une incroyable synchronisation des courants et des champs magnétiques), de même nature que la lumière du soleil : le spectre entier de la lumière blanche, de l infrarouge lointain aux rayons X très durs, est ainsi accessible et permet d analyser la matière et les matériaux, de les caractériser. Pour ne donner qu un exemple parmi des milliers, c est sur une des lignes de lumière de SOLEIL qu a tout récemment été révélée la composition des vernis utilisés par Antonio Stradivari pour protéger ses fameux violons... Comme toute idée qui paraît tellement simple au final, l idée de SOLEIL a nécessité des dizaines d année...

Ternary rhombohedral Laves phases RE_2Rh_3Ga (RE = Y, La-Nd, Sm, Gd-Er)

International Nuclear Information System (INIS)

Seidel, Stefan; Benndorf, Christopher; Heletta, Lukas; Poettgen, Rainer; Eckert, Hellmut; Sao Paulo Univ., Sao Carlos

2017-01-01

The ordered Laves phases RE_2Rh_3Ga (RE=Y, La-Nd, Sm, Gd-Er) were synthesized by arc-melting of the elements and subsequent annealing. The samples were characterized by powder X-ray diffraction (XRD). They crystallize with the rhombohedral Mg_2Ni_3Si type structure, space group R3m. Three structures were refined from single crystal X-ray diffractometer data: a=557.1(1), c=1183.1(2), wR2=0.0591, 159 F"2 values, 10 variables for Y_2Rh_3Ga, a=562.5(2), c=1194.4(2) pm, wR2=0.0519, 206 F"2 values, 11 variables for Ce_2Rh_3Ga and a=556.7(2), c=1184.1(3) pm, wR2=0.0396, 176 F"2 values, 11 variables for Tb_2Rh_3Ga. The Rh_3Ga tetrahedra are condensed via common corners and the large cavities left by the network are filled by the rare earth atoms. The RE_2Rh_3Ga Laves phases crystallize with a translationengleiche subgroup of the cubic RERh_2 Laves phases with MgCu_2 type. Magnetic susceptibility measurements reveal Pauli paramagnetism for Y_2Rh_3Ga and La_2Rh_3Ga. Ce_2Rh_3Ga shows intermediate cerium valence while all other RE_2Rh_3Ga phases are Curie-Weiss paramagnets which order magnetically at low temperatures. The "8"9Y and "7"1Ga solid state nuclear magnetic resonance (NMR) spectra of the diamagnetic representative Y_2Rh_3Ga show well-defined single resonances in agreement with an ordered bulk phase. In comparison to the binary Laves phase YRh_2 a strongly increased "8"9Y resonance frequency is observed owing to a higher s-electron spin density at the "8"9Y nuclei as proven by density of states (DOS) calculations.

Luminescence and magnetic behaviour of almond like (Na0.5La0.5)MoO4:RE3+ (RE = Eu, Tb, Dy) nanostructures

International Nuclear Information System (INIS)

Krishnan, Rajagopalan; Thirumalai, Jagannathan; Thomas, Sabu; Gowri, Mahasampath

2014-01-01

Graphical abstract: Monodispersed almond-like (Na 0.5 La 0.5 )MoO 4 :RE 3+ nanostructures synthesized by employing ethylene-diamine tetra acetic acid (EDTA) using hydrothermal route at 200 °C for 24 h. These nanoparticles were found to be novel bi-functional candidates suitable for high-quality luminescence and magnetic applications. - Highlights: • Almond like structures of (Na 0.5 La 0.5 )MoO 4 :RE 3+ were synthesized by hydrothermal method. • Time dependent self-assembly could be the dominant process for the formation of 3D networks. • Luminescence properties of nanosamples were studied in comparison with bulk sample. • Room temperature magnetic properties of bulk and nanophosphors were investigated. - Abstract: Tetragonal phase (Na 0.5 La 0.5 )MoO 4 :RE 3+ (RE = Eu, Tb, Dy) with almond like hierarchical structures assembled from nanosheets building blocks were successfully synthesized by employing disodium ethylenediaminetetraacetic acid (Na 2 EDTA) using hydrothermal route at 200 °C for 24 h. Field emission scanning electron microscope, transmission electron microscope, and X-ray diffraction patterns were used to characterize the morphology, size, and crystal structure with good resolution. The sequestering agent EDTA acts as quadridentate ligand coordinated with metal ions [Na + , La 3+ /RE 3+ ] facilitating the formation of self-organized 3D networks. The growth mechanism for the formation of almond like nanostructures is explicated in four paths: dissolution, adsorption, in situ transformation in acidic and basic media and the effective collision. Photoluminescence excitation and emission spectra reveals a spectral blue shift which was observed in the nanosamples towards shorter wavelengths compared with the bulk sample. Upon UV irradiation, both bulk and nanostructure show strong luminescence in the red region due to the 5 D 0 → 7 F 2 transition in Eu 3+ . Also, Tb 3+ and Dy 3+ doped (Na 0.5 La 0.5 )MoO 4 phosphor exhibit green and yellow

Problems experienced by women re-entering into the education profession / Melanie Beyers

OpenAIRE

Beyers, Melanie

2001-01-01

This study investigated problems experienced by women re-entering into the education profession by focusing on: • The nature and scope of re-entry by women into the education profession; • the features and problems experienced by women on re-entering the education profession; • the problems women educators experience on re-entering the education profession in the North West Province. To achieve these goals, both an empirical survey and a survey of literature was conducted. The study...

Workforce re-entry for Japanese unemployed dental hygienists.

Science.gov (United States)

Usui, Y; Miura, H

2015-02-01

The aim of this study was to define the profile of unemployed dental hygienists who could be enticed to re-enter the workforce and the factors that could facilitate their re-entry into the dental field in Japan. The questionnaire was mailed with a postage-paid return envelope to a sample of 3095 licensed dental hygienists. A 50.4% response rate (S = 1477) was observed. The rate of working dental hygienists was 60.3% (n = 891), and of unemployed dental hygienists was 39.7% (n = 586). Of the latter, 31.9% (n = 187) stated intentions of returning to the workplace. The unemployed dental hygienists seeking employment were more often married and had more children, compared with working dental hygienists currently. This group also had significantly fewer total service years. Moreover, only 11.96% of them belonged to the Japan Dental Hygienists' Association, and 41.3% of those attended training workshops. According to their response, they perceived their top three major barriers to re-entry as 'lack sufficient dental hygiene skill', 'child rearing' and 'poor working atmosphere'. 'Flexibility in the work schedule' and 'location' were the most important factors for re-entry from their perspective. There were not many dental hygienists hoping to return to the dental field. The findings suggested that strategies to encourage non-practicing dental hygienists to re-entry should be emphasized in the areas of a flexible working atmosphere, easy access to information on how to return to practice and guidance on how to maintain professionalism during inactivity. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Viking re-enactment

DEFF Research Database (Denmark)

Konzack, Lars

2017-01-01

In Chapter 4 we meet many different participants such as archaeology students, tradespeople, re-enactors, horseback riders, archers and many more who are all partaking in the same Viking market at Moesgaard Museum, Denmark. The purpose of this chapter is to present Moesgaard Viking Moot...... as a participatory local heritage event with a diverse range of spectators and participants. Lars Konzack shows how the different participants have developed their interaction with and interpretation of the Viking age through the market’s 40-year history....

Gettysburg re-imagined

DEFF Research Database (Denmark)

Chronis, Athinodoros; Arnould, Eric J.; Hampton, Ronald D.

2012-01-01

and expands narrative-based theories of consumption experiences. We argue that the workings of imagination in tourism sites are inextricably linked to the production of cultural imaginaries, that is, socially important narratives invested with collective values; we illustrate the process through which...... narrative of the American Civil War and we explore ethnographically the ways in which this historical episode is (re)imagined and articulated in tourism at Gettysburg. Our research provides an alternative account to mental imagery theory that is based on restrictive cognitive conceptions of imagination...

Microstructural analyses and critical current densities in the high-Tc superconductor system ReBa2Cu3OX, with RE = Y, Sm, Eu, Gd, Dy, Ho

International Nuclear Information System (INIS)

Schindler, G.; Seebacher, B.

1989-01-01

The authors report on investigations into the impact of the rare earths (RE) as given in the title on the ceramic microstructure and the critical current density j c in the superconductor system REBa 2 Cu 3 O x . With RE = Sm, Eu, or Gd, the material is homogeneous in phase and crystallizes in platelets with maximum sizes of up to 350 μm. Material with RE = Y, Dy, or Ho exhibits grain sizes up to 500 μm, and a low amount of phase inhomogeneities. The critical currents measured are between 25 Acm -2 and 290 Acm -2 at 77 K, without external field. The highest values are found in systems with RE = Eu or Gd. (orig.) [de

Immediate re-transplantation following early kidney transplant thrombosis.

LENUS (Irish Health Repository)

Phelan, Paul J

2012-02-01

Allograft thrombosis is a devastating early complication of renal transplantation that ultimately leads to allograft loss. We report here on our experience of nine cases of immediate re-transplantation following early kidney transplant thrombosis at a single centre between January 1990 and June 2009. The mean age was 42.9 years at time of transplant. For seven patients, the allograft thrombosis was their first kidney transplant and seven of the nine cases had a deceased donor transplant. The initial transplants functioned for a mean of 1.67 days and the patients received a second allograft at a mean of 3.1 days after graft failure. All of the re-transplants worked immediately. Four allografts failed after a mean of 52.5 months (2-155 months). Two of these died with a functioning allograft, one failed owing to chronic allograft nephropathy and one owing to persistent acute cellular rejection. The remaining five patients still have a functioning allograft after a mean of 101.8 months (7-187 months). One year allograft and patient survival after re-transplantation were 87.5% and 100% respectively (after 5 years, both were 57%). Immediate re-transplantation following early kidney transplant thrombosis can be a success. It may be considered in selected cases after allograft thrombosis.

Attribute-based proxy re-encryption with keyword search.

Science.gov (United States)

Shi, Yanfeng; Liu, Jiqiang; Han, Zhen; Zheng, Qingji; Zhang, Rui; Qiu, Shuo

2014-01-01

Keyword search on encrypted data allows one to issue the search token and conduct search operations on encrypted data while still preserving keyword privacy. In the present paper, we consider the keyword search problem further and introduce a novel notion called attribute-based proxy re-encryption with keyword search (ABRKS), which introduces a promising feature: In addition to supporting keyword search on encrypted data, it enables data owners to delegate the keyword search capability to some other data users complying with the specific access control policy. To be specific, ABRKS allows (i) the data owner to outsource his encrypted data to the cloud and then ask the cloud to conduct keyword search on outsourced encrypted data with the given search token, and (ii) the data owner to delegate other data users keyword search capability in the fine-grained access control manner through allowing the cloud to re-encrypted stored encrypted data with a re-encrypted data (embedding with some form of access control policy). We formalize the syntax and security definitions for ABRKS, and propose two concrete constructions for ABRKS: key-policy ABRKS and ciphertext-policy ABRKS. In the nutshell, our constructions can be treated as the integration of technologies in the fields of attribute-based cryptography and proxy re-encryption cryptography.

Attribute-Based Proxy Re-Encryption with Keyword Search

Science.gov (United States)

Shi, Yanfeng; Liu, Jiqiang; Han, Zhen; Zheng, Qingji; Zhang, Rui; Qiu, Shuo

2014-01-01

Keyword search on encrypted data allows one to issue the search token and conduct search operations on encrypted data while still preserving keyword privacy. In the present paper, we consider the keyword search problem further and introduce a novel notion called attribute-based proxy re-encryption with keyword search (), which introduces a promising feature: In addition to supporting keyword search on encrypted data, it enables data owners to delegate the keyword search capability to some other data users complying with the specific access control policy. To be specific, allows (i) the data owner to outsource his encrypted data to the cloud and then ask the cloud to conduct keyword search on outsourced encrypted data with the given search token, and (ii) the data owner to delegate other data users keyword search capability in the fine-grained access control manner through allowing the cloud to re-encrypted stored encrypted data with a re-encrypted data (embedding with some form of access control policy). We formalize the syntax and security definitions for , and propose two concrete constructions for : key-policy and ciphertext-policy . In the nutshell, our constructions can be treated as the integration of technologies in the fields of attribute-based cryptography and proxy re-encryption cryptography. PMID:25549257

Study of radiation synovectomy using 188Re-sulfide

International Nuclear Information System (INIS)

Chen Gang; Li Peiyong; Jiang Xufeng; Zhang Liying; Wang Xuefeng; Sun Zhenming; Zhang Huan

2002-01-01

Objective: To study the radiation synovectomy with 188 Re-sulfide. Methods: Thirty cases were divided into 2 groups, the group with hemophilia and the group with rheumatoid arthritis (RA). Patients with joint synovitis were injected different doses of 188 Re-sulfide, 222 - 444 MBq intra-articular. MRI was taken before and 3 - 6 months after the radiation synovectomy to evaluate the treatment efficacy, and the symptoms were also evaluated. Results: MRI study showed that after the treatment the synovium became thiner and the edema was reduced in the lesioned joint. The symptoms were improved with the pain relieved and duration of intra-articular hemorrhage reduced. Conclusions: Radiation synovectomy using 188 Re-sulfide has effects on synovitis. It can be used clinically to improve the symptoms of joint synovitis and reduce the duration of intra-articular hemorrhage

Microstructure and Properties of Porous Si3N4/Dense Si3N4 Joints Bonded Using RE–Si–Al–O–N (RE = Y or Yb Glasses

Directory of Open Access Journals (Sweden)

Ling Li

2017-11-01

Full Text Available The joining of porous Si3N4 to dense Si3N4 ceramics has been successfully performed using mixed RE2O3 (RE = Y or Yb, Al2O3, SiO2, and α-Si3N4 powders. The results suggested that the α-Si3N4 powders partly transformed into β-SiAlON and partly dissolved into oxide glass to form oxynitride glass. Thus, composites of glass/β-SiAlON-ceramic formed in the seam of joints. Due to the capillary action of the porous Si3N4 ceramic, the molten glass solder infiltrated into the porous Si3N4 ceramic side during the joining process and formed the “infiltration zone” with a thickness of about 400 μm, which contributed to the heterogeneous distribution of the RE–Si–Al–O–N glasses in the porous Si3N4 substrate. In-situ formation of β-SiAlON in the seam resulted in a high bonding strength. The maximum bending strength of 103 MPa and 88 MPa was reached for the porous Si3N4/dense Si3N4 joints using Y–Si–Al–O–N and Yb–Si–Al–O–N glass solders, respectively.

A emergência do autor Pierre Rivière/The emergence of the Pierre Rivière author

Directory of Open Access Journals (Sweden)

Adriana Duarte Bonini Mariguela

2007-01-01

Full Text Available Nesse artigo apresento uma análise do caso de parricídio / fraticídio cometido por um jovem camponês francês, nascido na comuna de Courvaudon, Pierre Rivière que em 3 de junho de 1835, aos vinte anos, assassinou a golpes de foice sua mãe grávida de sete meses, sua irmã de 18 anos, e seu irmão de sete anos. O livro intitulado Eu, Pierre Rivière, que degolei minha mãe, minha irmã e meu irmão produzido pelo trabalho de uma equipe de pesquisadores, no Collège de France, sob a coordenação de Michel Foucault em 1973, apresenta em seu conjunto notícias de jornais, testemunhos, interrogatórios, laudos médicos e uma gama de diferentes discursos. Para empreender a análise do nó entre a escrita e o assassinato, utilizo a relação entre a escrita e o autor demarcando o personagem Rivière no desdobramento, na ordem do corpo e da linguagem. This paper has as aim to present an analysis of the case of patricide / fratricide cometed by a French Countryman, Pierre Rivière, who was born in the commune of Courvaudon, who, on July 3rd, 1835, at age of 20, killed his mother, his brother and sister with a sickle. His mother was in the seventh month of pregnancy, his sister was 18 and his brother was 7 years old. The book, whose name was “I, Pierre Riviere, Having Slaughtered My Mother, My Sister, and My Brother ...: A Case of Parricide in the Nineteenth Century” was produced by a group of researchers at the Collège de France, under the coordination of Michel Foucault in 1973, has a set of newspaper news, witnesses, inquiring, forensic medical reports and a variety of different texts. To understand and analyze the writings and the homicide, the relationship between writing and the author is used, marking the character Rivière unfolding body and language.

Dosimetric benefit of adaptive re-planning in pancreatic cancer stereotactic body radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Li, Yongbao [Department of Engineering Physics, Tsinghua University, Key Laboratory of Particle & Radiation Imaging (Tsinghua University), Ministry of Education, Beijing (China); Center for Advanced Radiotherapy Technologies University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of Texas Southwestern Medical Center, Dallas, TX (United States); Hoisak, Jeremy D.P.; Li, Nan; Jiang, Carrie [Center for Advanced Radiotherapy Technologies University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of California San Diego, La Jolla, CA (United States); Tian, Zhen [Center for Advanced Radiotherapy Technologies University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of Texas Southwestern Medical Center, Dallas, TX (United States); Gautier, Quentin; Zarepisheh, Masoud [Center for Advanced Radiotherapy Technologies University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of California San Diego, La Jolla, CA (United States); Wu, Zhaoxia; Liu, Yaqiang [Department of Engineering Physics, Tsinghua University, Key Laboratory of Particle & Radiation Imaging (Tsinghua University), Ministry of Education, Beijing (China); Jia, Xun [Center for Advanced Radiotherapy Technologies University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of California San Diego, La Jolla, CA (United States); Department of Radiation Oncology, University of Texas Southwestern Medical Center, Dallas, TX (United States); and others

2015-01-01

Stereotactic body radiotherapy (SBRT) shows promise in unresectable pancreatic cancer, though this treatment modality has high rates of normal tissue toxicity. This study explores the dosimetric utility of daily adaptive re-planning with pancreas SBRT. We used a previously developed supercomputing online re-planning environment (SCORE) to re-plan 10 patients with pancreas SBRT. Tumor and normal tissue contours were deformed from treatment planning computed tomographies (CTs) and transferred to daily cone-beam CT (CBCT) scans before re-optimizing each daily treatment plan. We compared the intended radiation dose, the actual radiation dose, and the optimized radiation dose for the pancreas tumor planning target volume (PTV) and the duodenum. Treatment re-optimization improved coverage of the PTV and reduced dose to the duodenum. Within the PTV, the actual hot spot (volume receiving 110% of the prescription dose) decreased from 4.5% to 0.5% after daily adaptive re-planning. Within the duodenum, the volume receiving the prescription dose decreased from 0.9% to 0.3% after re-planning. It is noteworthy that variation in the amount of air within a patient's stomach substantially changed dose to the PTV. Adaptive re-planning with pancreas SBRT has the ability to improve dose to the tumor and decrease dose to the nearby duodenum, thereby reducing the risk of toxicity.

Re-purification of labelled ferritin antigen with HPLC

International Nuclear Information System (INIS)

Zhang Haoyi; Jin Lichun

2002-01-01

Objective: To improve the quality of long-term stored labelled ferritin antigen with HPLC. Methods: The antigen was analyzed and purified with HPLC and again analyzed with RIA afterwards. Results: Ferritin antigen underwent significant polymerization after long-term (aggregation) storage. After re-purification with HPLC, its immuno-activity and labelled specific radioactivity were both significantly improved. Conclusion: Quality of stored ferritin RIA kit could be greatly improved after re-purification with HPLC

Energetics of stepwise disordering transformation in pyrochlores, RE2Ti2O7 (RE = Y, Gd and Dy)

International Nuclear Information System (INIS)

Hayun, Shmuel; Tran, Tien B.; Lian, Jie; Fuentes, Antonio F.; Navrotsky, Alexandra

2012-01-01

Graphical abstract: The transformation from disordered to more order state in the pyrochlore system go through multiple energetics steps; the cation sublattice rearrangement is control by the diffusion of the cations while the anion sublattice display an irreversible transformation from a disordered to a higher-ordered state via diffusionless transformation. - Abstract: The capacity to incorporate actinide cations makes pyrochlore titanates first-choice phases in titanate-based waste form ceramics. Despite broad interest in the pyrochlore order–disorder transformation due to the cumulative effects of 238 U, 235 U and 232 Th radioactive decay and their daughter products, only limited thermodynamic data, mainly based on simulations of ion-beam irradiation experiments, have been reported. In this work, for the first time, heavily disordered pyrochlores, RE 2 Ti 2 O 7 (RE = Y, Gd and Dy), from mechanical milling of their constituent oxides, were thermochemically investigated. Two types of thermal events were identified using high-temperature differential scanning calorimetry and correlated to the structural disorder in the cation and anion sublattices. Moreover, the excess formation energy measured by oxide melt solution calorimetry shows that the smaller the ionic radius of the RE, the easier it is to remove damage domains.

Predictors of homeless services re-entry within a sample of adults receiving Homelessness Prevention and Rapid Re-Housing Program (HPRP) assistance.

Science.gov (United States)

Brown, Molly; Vaclavik, Danielle; Watson, Dennis P; Wilka, Eric

2017-05-01

Local and national evaluations of the federal Homelessness Prevention and Rapid Re-Housing Program (HPRP) have demonstrated a high rate of placement of program participants in permanent housing. However, there is a paucity of research on the long-term outcomes of HPRP, and research on rehousing and prevention interventions for single adults experiencing homelessness is particularly limited. Using Homeless Management Information System data from 2009 to 2015, this study examined risk of return to homeless services among 370 permanently housed and 71 nonpermanently housed single adult HPRP participants in Indianapolis, Indiana. Kaplan-Meier survival curves were conducted to analyze time-to-service re-entry for the full sample, and the homelessness prevention and rapid rehousing participants separately. With an average follow-up of 4.5 years after HPRP exit, 9.5% of the permanently housed HPRP participants and 16.9% of those nonpermanently housed returned to homeless services. By assistance type, 5.4% of permanently housed and 15.8% of nonpermanently housed homelessness prevention recipients re-entered services, and 12.8% of permanently housed and 18.2% of nonpermanently housed rapid rehousing recipients re-entered during the follow-up period. Overall, veterans, individuals receiving rapid rehousing services, and those whose income did not increase during HPRP had significantly greater risk of returning to homeless services. Veterans were at significantly greater risk of re-entry when prevention and rehousing were examined separately. Findings suggest a need for future controlled studies of prevention and rehousing interventions for single adults, aiming to identify unique service needs among veterans and those currently experiencing homelessness in need of rehousing to inform program refinement. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

High rate of virological re-suppression among patients failing ...

African Journals Online (AJOL)

Results. Of 69 patients enrolled in the programme, 40 had at least one follow-up VL and no known drug resistance at enrolment; 27 (68%) of these re-suppressed while remaining on second-line ART following enhanced adherence support. The majority (18/27; 67%) achieved re-suppression within the first 3 months in the ...

Carcass glycogen repletion on carbohydrate re-feeding after starvation.

OpenAIRE

Cox, D J; Palmer, T N

1987-01-01

In mice, the response of carcass glycogen to glucose re-feeding after starvation is biphasic. The initial repletive phase is followed by partial (greater than 50%) glycogen mobilization. This turnover of carcass glycogen in response to carbohydrate re-feeding may play an important role in the provision of C3 precursors for hepatic glycogen synthesis.

Application of the FADS system on the Re-entry Module

Science.gov (United States)

Zhen, Huang

2016-07-01

The aerodynamic model for Flush Air Data Sensing System (FADS) is built based on the surface pressure distribution obtained through the pressure orifices laid on specific positions of the surface,and the flight parameters,such as angle of attack,angle of side-slip,Mach number,free-stream static pressure and dynamic pressure are inferred from the aerodynamic model.The flush air data sensing system (FADS) has been used on several flight tests of aircraft and re-entry vehicle,such as,X-15,space shuttle,F-14,X-33,X-43A and so on. This paper discusses the application of the FADS on the re-entry module with blunt body to obtain high-precision aerodynamic parameters.First of all,a basic theory and operating principle of the FADS is shown.Then,the applications of the FADS on typical aircrafts and re-entry vehicles are described.Thirdly,the application mode on the re-entry module with blunt body is discussed in detail,including aerodynamic simulation,pressure distribution,trajectory reconstruction and the hardware shoule be used,such as flush air data sensing system(FADS),inertial navigation system (INS),data acquisition system,data storage system.Finally,ablunt module re-entry flight test from low earth orbit (LEO) is planned to obtain aerodynamic parameters and amend the aerodynamic model with this FADS system data.The results show that FADS system can be applied widely in re-entry module with blunt bodies.

Re-tuning tuned mass dampers using ambient vibration measurements

International Nuclear Information System (INIS)

Hazra, B; Sadhu, A; Narasimhan, S; Lourenco, R

2010-01-01

Deterioration, accidental changes in the operating conditions, or incorrect estimates of the structure modal properties lead to de-tuning in tuned mass dampers (TMDs). To restore optimal performance, it is necessary to estimate the modal properties of the system, and re-tune the TMD to its optimal state. The presence of closely spaced modes and a relatively large amount of damping in the dominant modes renders the process of identification difficult. Furthermore, the process of estimating the modal properties of the bare structure using ambient vibration measurements of the structure with the TMD is challenging. In order to overcome these challenges, a novel identification and re-tuning algorithm is proposed. The process of identification consists of empirical mode decomposition to separate the closely spaced modes, followed by the blind identification of the remaining modes. Algorithms for estimating the fundamental frequency and the mode shape of the primary structure necessary for re-tuning the TMD are proposed. Experimental results from the application of the proposed algorithms to identify and re-tune a laboratory structure TMD system are presented

In-house Preparation of 188W/188Re Generators

International Nuclear Information System (INIS)

Sriwiang, Wiranee; Minsakorn, Napharat; Wardwilai, Charudej; Yindirum, Chareon; Sangsuriyan, Jatupol

2007-08-01

Full text: Low activity 188W/188Re generators were developed for the purpose of routinely supplying rhenium-188 for laboratory experiments and research works. Chromatography technology was applied in the construction of the generators. The chromatography columns containing 1.74 g alumina (Al2O3) were housed in plastic (PE) shielding inside the 30mm thick lead shield. Three generators were loaded with three different 188W activities; 25mCi (RG1), 25 mCi (RG2) and 50 mCi (RG3). Generator performances were determined in terms of elution yields, radiochemical purity, Al-breakthrough, 188W-breakthrough, and radionuclidic purity of the eluted products. These generators can be used for more than 6 months with average elution yields greater than 90 %. Radiochemical purity of 188ReO4- was high (> 99.7 % by ITLC), low level of 188W -breakthrough and low contamination of 192Ir and 191Os. There were only less than 1 ppm of 186W carrier and less than 3 ppm of Al-breakthrough. Key words: 188W/188Re, Generator, 188Re, Radionuclide

A tale of two re-branded cities:Riga, Latvia and Aarhus, Denmark

DEFF Research Database (Denmark)

Locmele, Gunta; Mousten, Birthe

2016-01-01

This study shows how Riga and Arhus identified, formulated and communicated city re-branding. Our analysis concentrates on resident responses to city re-branding and how such responses could force the municipalities to withdraw their re-branding. A city loses its identity if it is globalized...

Alternation of apoptotic and implanting genes expression of mouse embryos after re-vitrification

Science.gov (United States)

Majidi Gharenaz, Nasrin; Movahedin, Mansoureh; Mazaheri, Zohreh; Pour beiranvand, Shahram

2016-01-01

Background: Nowadays, oocytes and embryos vitrification has become a routine technique. Based on clinical judgment, re-vitrification maybe required. But little is known about re-vitrification impact on genes expression. Objective: The impact of re-vitrification on apoptotic and implanting genes, Bax, Bcl-2 and ErbB4, at compaction stage embryos were evaluated in this study. Materials and Methods: In this experimental study, 8 cell embryos (n=240) were collected from female mature mice, 60-62 hr post HCG injection. The embryos were divided randomly to 3 groups included: fresh (n=80), vitrified at 8 cell stage (n=80), vitrified at 8 cell stage thawed and re-vitrified at compaction stage (n=80). Embryos were vitrified by using cryolock, (open system) described by Kuwayama. Q-PCR was used to examine the expression of Bax, Bcl2 ErbB4 genes in derived blastocysts. Results: Our result showed that expanded blastocyst rate was similar between vitrified and re-vitrified groups, while re-vitrified embryos showed significant decrease in expanded blastocyst rate comparing with fresh embryos (p=0.03). In addition, significant difference was observed on apoptotic gene expression when comparing re-vitrified and fresh embryos (p=0.004), however expression of Bax and Bcl-2 (apoptotic) genes didn't demonstrate a significant difference between re-vitrified and vitrified groups. The expression rate of ErbB4, an implantation gene was decreased in re-vitrified embryos comparing with fresh embryos (p=0.003), but it was similar between re-vitrified and vitrified embryos. Conclusion: Re-vitrification can alter the expression of Bax, Bcl-2 and ErbB4 genes and developmental rate of mouse embryos in compaction stage. PMID:27679826

Catalysts for selective hydrogenation of furfural derived from the double complex salt [Pd(NH 3 ) 4 ](ReO 4 ) 2 on γ-Al 2 O 3

Energy Technology Data Exchange (ETDEWEB)

Thompson, Simon T.; Lamb, H. Henry

2017-06-01

The double complex salt [Pd(NH3)4](ReO4)2 was employed as precursor of supported bimetallic catalysts for selective hydrogenation of furfural. Direct reduction of [Pd(NH3)4](ReO4)2 on γ-Al2O3 in flowing H2 at 400 °C yields bimetallic nanoparticles 1–2 nm in size that exhibit significant interaction between the metals, as evidenced by temperature-programmed hydride decomposition (complete suppression of β-PdHx formation), extended X-ray absorption fine structure spectroscopy at the Pd K and Re LIII edges (PdRe distance = 2.72 Å), and scanning transmission electron microscopy with energy dispersive X-ray analysis. In contrast, calcination of [Pd(NH3)4](ReO4)2 on γ-Al2O3 at 350 °C in air and subsequent reduction in H2 at 400 °C results in metal segregation and formation of large (>50 nm) supported Pd particles; Re species cover the Pd particles and γ-Al2O3 support. A PdRe 1:2 catalyst prepared by sequential impregnation and calcination using HReO4 and [Pd(NH3)4](NO3)2 has a similar morphology. The catalyst derived by direct reduction of [Pd(NH3)4](ReO4)2 on γ-Al2O3 exhibits remarkably high activity for selective hydrogenation of furfural to furfuryl alcohol (FAL) at 150 °C and 1 atm. Suppression of H2 chemisorption via elimination of Pd threefold sites, as evidenced by CO diffuse-reflectance infrared Fourier transform spectroscopy, correlates with increased FAL selectivity.

Present status of research on Re-186 radiopharmaceuticals at Radioisotope Production Center

Energy Technology Data Exchange (ETDEWEB)

Mutalib, A [Radioisotope Production Center, National Atomic Energy Agency Kawasan PUSPIPTEK, Serpong (Indonesia)

1998-10-01

Rhenium shows a close chemical similarity to technetium and is suitable for radiotherapy because the {beta}-emitting radionuclides {sup 186}Re (t{sub 1/2} 90 h, E{sub {beta}} = 1.1 MeV, E{sub {gamma}} = 137 keV) and {sup 188}Re (t{sub 1/2} = 17 h, E{sub {beta}} = 2.1 MeV). The {gamma}-emission associated with decay of {sup 186}Re is also useful in scintigraphy. The research on {sup 186}Re radiopharmaceuticals at Radioisotope Production Center has been carried out since April 1997. Interest in radioimmunotherapy (RIT) led us to the development of labeling antibodies with rhenium isotopes. Although there are several methods for coupling radiometal to antibody, we prefer an indirect labeling method in which a bifunctional chelating agent is used for coupling of {sup 186}Re to monoclonal antibodies. In this report we outline the study on the preparation of {sup 186}Re DMSA-TFP as precursor for labeling with monoclonal antibody. (author)

Re-engineering caused by ISO-9000 certification

DEFF Research Database (Denmark)

Hvam, Lars; Nielsen, Anders Paarup; Bjarnø, Ole-Christian

1997-01-01

Based on a project performed at a medium-sized producer of medical utensils, reviews some of the problems which the company experienced in connection with the system built up during ISO 9001 certification, and the re-engineering efforts which were performed in order to relieve these problems....... Focuses in particular on a re-structuring of the company’s system for production documentation and its relation to the traceability of their products. This system was radically altered during the project without the traceability requirements being violated or reduced. These changes resulted in a marked...... increase in productivity....

Le mystère du monde quantique

CERN Document Server

Damour, Thibault

2016-01-01

Avec Bob et son chien, Rick, embarquez pour une joyeuse épopée dans les mystères du monde quantique ! La physique quantique est partout autour de nous, tant dans l'infiniment grand que dans l'infiniment petit. Mais ce qu'elle dit du monde qui nous entoure diffère de manière vertigineuse de ce qu'on observe et ressent au quotidien. Partez à la rencontre de ceux qui ont théorisé et créé la physique quantique : Planck, Einstein, le prince de Broglie, Heisenberg, Schrödinger, Bohr, Born, Everett…

Menière-lignende symptomer efter meningeom

DEFF Research Database (Denmark)

Friis, Morten; Klokker, Mads; Fugleholm, Kåre

2010-01-01

A 36-year-old woman who presented with a right sided hearing loss, tinnitus and attacks of dizziness was initially diagnosed with Ménière's disease. A meningioma was found along the posterior surface of the petrosal bone, centred partly on the external aperture of the vestibular aqueduct with no ......A 36-year-old woman who presented with a right sided hearing loss, tinnitus and attacks of dizziness was initially diagnosed with Ménière's disease. A meningioma was found along the posterior surface of the petrosal bone, centred partly on the external aperture of the vestibular aqueduct...

Les paradoxes de la matière

CERN Document Server

2013-01-01

Si nous devons la multitude d’appareils numériques actuels à l’électronique, celle-ci atteint ses limites. Comment les dépasser ? En explorant les propriétés spectaculaires de la matière ! Et les candidats au remplacement de l’électronique sont nombreux : oxytronique, spintronique, plasmonique, magnonique, graphène... Nous réservant aussi bien d’autres surprises - tels les capes d’invisibilité, les plastiques conducteurs, les polymères autocicatrisants, les protections antisismiques, etc - les études sur la matière n’ont pas fini de nous étonner.

Determination of radiochemical yields of 186Re-labelled complexes using thin layer chromatography

International Nuclear Information System (INIS)

Konirova, R.; Kohlickova, M.; Jedinakova-Krizova, V.

1999-01-01

The reaction conditions for synthesis of three rhenium complexes 186 Re-methylendiphosphonate (MDP), 186 Re-hydroxyethylidendiphosphonate (HEDP) and 186 Re-citrate have been investigated. Radiochemical yield of complexation has been determined by thin layer chromatography and paper chromatography. The rhenium complexation with corresponding ligand is dependent on pH values of reaction mixture, concentration of studied ligand (MDP, HEDP and sodium citrate) and concentration of reducing agent. Stannous chloride with ascorbic acid (as antioxidant) was used for reduction of perrhenate. The labeling yield of 186 Re-MDP was about 90 %, of 186 Re-HEDP more than 80 % and more than 75 % for 186 Re-citrate under optimum conditions. Besides, the possibility of application of porphyrins as organic ligands for complexation with rhenium isotopes is examined. (authors)

Problems of rotator cuff re-tear cases. Examination of operative findings

International Nuclear Information System (INIS)

Ishitani, Eiichi; Matsuura, Komei; Shin, Kunichika; Kawamoto, Taisaku; Hosokawa, Akira

2007-01-01

High re-tear rate is reported after rotator cuff repair in large and massive tear cases. Previously, we reported that 15% of patients after rotator cuff repair showed re-tear in MRI findings. In this study, 116 consecutive rotator cuff repaired patients who had been operated arthroscopically since 2003 were evaluated for size, torn site, fixation methods, mobility, and tendon quality. In addition, rehabilitation methods and occupation after revision were also evaluated. There were four patients who underwent re-operation. Rotator cuff repairs by revision surgery failed mechanically due to two reasons: the main factor of failure was suture material breakage in three cases and the second was tendon pulling through sutures in one case. The lack of thread strength was suggested. In addition, it is important to pull cuff stump to greater tubercle without excessive tension. Of re-operated cases, three engaging in manual labor suffered large and massive tear. In two cases, premature return to manual labor suggested cause of re-tear. (author)

Narrowing the gap: from semiconductor to semimetal in the homologous series of rare-earth zinc arsenides RE(2-y)Zn4As4·n(REAs) and Mn-substituted derivatives RE(2-y)Mn(x)Zn(4-x)As4·n(REAs) (RE = La-Nd, Sm, Gd).

Science.gov (United States)

Lin, Xinsong; Tabassum, Danisa; Mar, Arthur

2015-12-14

A homologous series of ternary rare-earth zinc arsenides, prepared by reactions of the elements at 750 °C, has been identified with the formula RE(2-y)Zn4As4·n(REAs) (n = 2, 3, 4) for various RE members. They adopt trigonal structures: RE(4-y)Zn4As6 (RE = La-Nd), space group R3̄m1, Z = 3; RE(5-y)Zn4As7 (RE = Pr, Nd, Sm, Gd), space group P3̄m1, Z = 1; RE(6-y)Zn4As8 (RE = La-Nd, Sm, Gd), space group R3̄m1, Z = 3. The Zn atoms can be partially substituted by Mn atoms, resulting in quaternary derivatives RE(2-y)Mn(x)Zn(4-x)As4·n(REAs). Single-crystal structures were determined for nine ternary and quaternary arsenides RE(2-y)M4As4·n(REAs) (M = Mn, Zn) as representative examples of these series. The structures are built by stacking close-packed nets of As atoms, sometimes in very long sequences, with RE atoms occupying octahedral sites and M atoms occupying tetrahedral sites, resulting in an intergrowth of [REAs] and [M2As2] slabs. The recurring feature of all members of the homologous series is a sandwich of [M2As2]-[REAs]-[M2As2] slabs, while rocksalt-type blocks of [REAs] increase in thickness between these sandwiches with higher n. Similar to the previously known related homologous series REM(2-x)As2·n(REAs) which is deficient in M, this new series RE(2-y)M4As4·n(REAs) exhibits deficiencies in RE to reduce the electron excess that would be present in the fully stoichiometric formulas. Enthalpic and entropic factors are considered to account for the differences in site deficiencies in these two homologous series. Band structure calculations indicate that the semiconducting behaviour of the parent n = 0 member (with CaAl2Si2-type structure) gradually evolves, through a narrowing of the gap between valence and conduction bands, to semimetallic behaviour as the number of [REAs] blocks increases, to the limit of n = ∞ for rocksalt-type REAs.

From Retreat to Re-engagement: The New American Foreign Policy ...

African Journals Online (AJOL)

From Retreat to Re-engagement: The New American Foreign Policy for ... that the re-engagement with Sub-Saharan Africa, is based on US perception of threats ... in the subordination of the region to the world's only superpower and its allies.

Performance assurance of the re-applying project documentation

Science.gov (United States)

Kozlova, Olga

2017-10-01

Usage of the re-applying project documentation is cost effective measure. Saving of budgetary funds for purchases for development of new project documentation occurs by means of it. It also becomes possible to consider better decisions and prevent the repetition of mistakes. Nowadays, state authorities in construction management are forming separate institute for re-applying project documentation. The article shows the main tasks of such events and the issues to be solved for achievement of a high positive result.

Binding of ReO4- with an engineered MoO42--binding protein: towards a new approach in radiopharmaceutical applications

International Nuclear Information System (INIS)

Aryal, Baikuntha P.; Brugarolas, Pedro; He, Chuan

2012-01-01

Radiolabeled biomolecules are routinely used for clinical diagnostics. 99m Tc is the most commonly used radioactive tracer in radiopharmaceuticals. 188 Re and 186 Re are also commonly used as radioactive tracers in medicine. However, currently available methods for radiolabeling are lengthy and involve several steps in bioconjugation processes. In this work we present a strategy to engineer proteins that may selectively recognize the perrhenate (ReO 4 - ) ion as a new way to label proteins. We found that a molybdate (MoO 4 2- )-binding protein (ModA) from Escherichia coli can bind perrhenate with high affinity. Using fluorescence and isothermal titration calorimetry measurements, we determined the dissociation constant of ModA for ReO 4 - to be 541 nM and we solved a crystal structure of ModA with a bound ReO 4 - . On the basis of the structure we created a mutant protein containing a disulfide linkage, which exhibited increased affinity for perrhenate (K d = 104 nM). High-resolution crystal structures of ModA (1.7 (angstrom)) and A11C/R153C mutant (2.0 (angstrom)) were solved with bound perrhenate. Both structures show that a perrhenate ion occupies the molybdate binding site using the same amino acid residues that are involved in molybdate binding. The overall structure of the perrhenate-bound ModA is unchanged compared with that of the molybdate-bound form. In the mutant protein, the bound perrhenate is further stabilized by the engineered disulfide bond.

Professional Re-Accreditation: Constructing Educational Policy for Career-Long Teacher Professional Learning

Science.gov (United States)

Watson, Cate; Fox, Alison

2015-01-01

Competence as a measure of "fitness to practice" and its evaluation through mechanisms of personal performance review, has led to the introduction of systems in a number of professions which link appraisal to the maintenance of professional registration (variously referred to as re-validation, re-certification, re-accreditation, etc.).…

Stereotactic body radiation therapy in the re-irradiation situation – a review

International Nuclear Information System (INIS)

Mantel, Frederick; Flentje, Michael; Guckenberger, Matthias

2013-01-01

Although locoregional relapse is frequent after definitive radiotherapy (RT) or multimodal treatments, re-irradiation is only performed in few patients even in palliative settings like e.g. vertebral metastasis. This is most due to concern about potentially severe complications, especially when large volumes are exposed to re-irradiation. With technological advancements in treatment planning the interest in re-irradiation as a local treatment approach has been reinforced. Recently, several studies reported re-irradiation for spinal metastases using SBRT with promising local and symptom control rates and simultaneously low rates of toxicity. These early data consistently indicate that SBRT is a safe and effective treatment modality in this clinical situation, where other treatment alternatives are rare. Similarly, good results have been shown for SBRT in the re-irradiation of head and neck tumors. Despite severe late adverse effects were reported in several studies, especially after single fraction doses >10 Gy, they appear less frequently compared to conventional radiotherapy. Few studies with small patient numbers have been published on SBRT re-irradiation for non-small cell lung cancer (NSCLC). Overall survival (OS) is limited by systemic progression and seems to depend particularly on patient selection. SBRT re-irradiation after primary SBRT should not be practiced in centrally located tumors due to high risk of severe toxicity. Only limited data is available for SBRT re-irradiation of pelvic tumors: feasibility and acceptable toxicity has been described, suggesting SBRT as a complementary treatment modality for local symptom control

Re-engineering pre-employment check-up systems: a model for improving health services.

Science.gov (United States)

Rateb, Said Abdel Hakim; El Nouman, Azza Abdel Razek; Rateb, Moshira Abdel Hakim; Asar, Mohamed Naguib; El Amin, Ayman Mohammed; Gad, Saad abdel Aziz; Mohamed, Mohamed Salah Eldin

2011-01-01

The purpose of this paper is to develop a model for improving health services provided by the pre-employment medical fitness check-up system affiliated to Egypt's Health Insurance Organization (HIO). Operations research, notably system re-engineering, is used in six randomly selected centers and findings before and after re-engineering are compared. The re-engineering model follows a systems approach, focusing on three areas: structure, process and outcome. The model is based on six main components: electronic booking, standardized check-up processes, protected medical documents, advanced archiving through an electronic content management (ECM) system, infrastructure development, and capacity building. The model originates mainly from customer needs and expectations. The centers' monthly customer flow increased significantly after re-engineering. The mean time spent per customer cycle improved after re-engineering--18.3 +/- 5.5 minutes as compared to 48.8 +/- 14.5 minutes before. Appointment delay was also significantly decreased from an average 18 to 6.2 days. Both beneficiaries and service providers were significantly more satisfied with the services after re-engineering. The model proves that re-engineering program costs are exceeded by increased revenue. Re-engineering in this study involved multiple structure and process elements. The literature review did not reveal similar re-engineering healthcare packages. Therefore, each element was compared separately. This model is highly recommended for improving service effectiveness and efficiency. This research is the first in Egypt to apply the re-engineering approach to public health systems. Developing user-friendly models for service improvement is an added value.

Preparation and certification of Re-Os dating reference materials: Molybdenites HLP and JDC

Science.gov (United States)

Du, A.; Wu, S.; Sun, D.; Wang, Shaoming; Qu, W.; Markey, R.; Stain, H.; Morgan, J.; Malinovskiy, D.

2004-01-01

Two Re-Os dating reference material molybdenites were prepared. Molybdenite JDC and molybdenite HLP are from a carbonate vein-type molybdenum-(lead)- uranium deposit in the Jinduicheng-Huanglongpu area of Shaanxi province, China. The samples proved to be homogeneous, based on the coefficient of variation of analytical results and an analysis of variance test. The sampling weight was 0.1 g for JDC and 0.025 g for HLP. An isotope dilution method was used for the determination of Re and Os. Sample decomposition and preconcentration of Re and Os prior to measurement were accomplished using a variety of methods: acid digestion, alkali fusion, ion exchange and solvent extraction. Negative thermal ionisation mass spectrometry and inductively coupled plasma-mass spectrometry were used for the determination of Re and 187Os concentration and isotope ratios. The certified values include the contents of Re and Os and the model ages. For HLP, the Re content was 283.8 ?? 6.2 ??g g-1, 187Os was 659 ?? 14 ng g-1 and the Re-Os model age was 221.4 ?? 5.6 Ma. For JDC, the Re content was 17.39 ?? 0.32 ng g-1, 187Os was 25.46 ?? 0.60 ng g-1 and the Re-Os model age was 139.6 ?? 3.8 Ma. Uncertainties for both certified reference materials are stated at the 95% level of confidence. Three laboratories (from three countries: P.R. China, USA, Sweden) joined in the certification programme. These certified reference materials are primarily useful for Re-Os dating of molybdenite, sulfides, black shale, etc.

Alternation of apoptotic and implanting genes expression of mouse embryos after re-vitrification

Directory of Open Access Journals (Sweden)

Nasrin Majidi Gharenaz

2016-08-01

Full Text Available Background: Nowadays, oocytes and embryos vitrification has become a routine technique. Based on clinical judgment, re-vitrification maybe required. But little is known about re-vitrification impact on genes expression. Objective: The impact of re-vitrification on apoptotic and implanting genes, Bax, Bcl-2 and ErbB4, at compaction stage embryos were evaluated in this study. Materials and Methods: In this experimental study, 8 cell embryos (n=240 were collected from female mature mice, 60-62 hr post HCG injection. The embryos were divided randomly to 3 groups included: fresh (n=80, vitrified at 8 cell stage (n=80, vitrified at 8 cell stage thawed and re-vitrified at compaction stage (n=80. Embryos were vitrified by using cryolock, (open system described by Kuwayama. Q-PCR was used to examine the expression of Bax, Bcl2 ErbB4 genes in derived blastocysts. Results: Our result showed that expanded blastocyst rate was similar between vitrified and re-vitrified groups, while re-vitrified embryos showed significant decrease in expanded blastocyst rate comparing with fresh embryos (p=0.03. In addition, significant difference was observed on apoptotic gene expression when comparing re-vitrified and fresh embryos (p=0.004, however expression of Bax and Bcl-2 (apoptotic genes didn't demonstrate a significant difference between re-vitrified and vitrified groups. The expression rate of ErbB4, an implantation gene was decreased in re-vitrified embryos comparing with fresh embryos (p=0.003, but it was similar between re-vitrified and vitrified embryos. Conclusion: Re-vitrification can alter the expression of Bax, Bcl-2 and ErbB4 genes and developmental rate of mouse embryos in compaction stage

Sodalite as a vehicle to increase Re retention in waste glass simulant during vitrification

Energy Technology Data Exchange (ETDEWEB)

Luksic, Steven A., E-mail: steven.luksic@pnnl.gov; Riley, Brian J.; Parker, Kent E.; Hrma, Pavel

2016-10-15

Technetium (Tc) retention during Hanford waste vitrification can be increased if the volatility can be controlled. Incorporating Tc into a thermally stable mineral phase, such as sodalite, is one way to achieve increased retention. Here, rhenium (Re)-bearing sodalite was tested as a vehicle to transport perrhenate (ReO{sub 4}{sup −}), a nonradioactive surrogate for pertechnetate (TcO{sub 4}{sup −}), into high-level (HLW) and low-activity waste (LAW) glass simulants. After melting HLW and LAW simulant feeds, the retention of Re in the glass was measured and compared with the Re retention in glass prepared from a feed containing Re{sub 2}O{sub 7}. Phase analysis of sodalite in both these glasses across a profile of temperatures describes the durability of Re-sodalite during the feed-to-glass transition. The use of Re sodalite improved the Re retention by 21% for HLW glass and 85% for LAW glass, demonstrating the potential improvement in Tc-retention if TcO{sub 4}{sup −} were to be encapsulated in a Tc-sodalite prior to vitrification. - Highlights: • Re retention is improved by incorporation into sodalite structure. • LAW-type glass shows lower retention but larger improvement with Re-sodalite. • Sodalite is stable to higher temperatures in high-alumina glass melts.

Timing of Re-Transfusion Drain Removal Following Total Knee Replacement

Science.gov (United States)

Leeman, MF; Costa, ML; Costello, E; Edwards, D

2006-01-01

INTRODUCTION The use of postoperative drains following total knee replacement (TKR) has recently been modified by the use of re-transfusion drains. The aim of our study was to investigate the optimal time for removal of re-transfusion drains following TKR. PATIENTS AND METHODS The medical records of 66 patients who had a TKR performed between October 2003 and October 2004 were reviewed; blood drained before 6 h and the total volume of blood drained was recorded. RESULTS A total of 56 patients had complete records of postoperative drainage. The mean volume of blood collected in the drain in the first 6 h was 442 ml. The mean total volume of blood in the drain was 595 ml. Therefore, of the blood drained, 78% was available for transfusion. CONCLUSION Re-transfusion drains should be removed after 6 h, when no further re-transfusion is permissible. PMID:16551400

Current technology and advances in true re-use of effluents

International Nuclear Information System (INIS)

Cillie, G.G.

1975-01-01

Increasing exploitation of natural water resources has necessitated true re-use of effluents. Such planned re-use is preferable to the indirect or incidental re-use which has hitherto been practised, sometimes indiscriminately. Modern technology provides the means for renovating effluents to any desired quality standard, including human consumption. The major obstacles still confronting widespread application of true re-use are the removal of nitrogen compounds and trace organic residues, including insecticides, herbicides and carcinogens. The need to guarantee hygienic quality by removal or destruction of all pathogens, including viruses and parasites, constitutes a major cost item. Radiation techniques may well be applied for sterilization and for destruction of organic radicals. A combination of various unit processes, for which design criteria and hardware are readily available, can be used to produce potable water at a cost of some 10 cents/m 3 for a 45 Ml/d plant. (author)

Immediate re-transplantation following early kidney transplant thrombosis.

LENUS (Irish Health Repository)

Phelan, Paul J

2011-08-01

Allograft thrombosis is a devastating early complication of renal transplantation that ultimately leads to allograft loss. We report here on our experience of nine cases of immediate re-transplantation following early kidney transplant thrombosis at a single centre between January 1990 and June 2009. The mean age was 42.9 years at time of transplant. For seven patients, the allograft thrombosis was their first kidney transplant and seven of the nine cases had a deceased donor transplant. The initial transplants functioned for a mean of 1.67 days and the patients received a second allograft at a mean of 3.1 days after graft failure. All of the re-transplants worked immediately. Four allografts failed after a mean of 52.5 months (2-155 months). Two of these died with a functioning allograft, one failed owing to chronic allograft nephropathy and one owing to persistent acute cellular rejection. The remaining five patients still have a functioning allograft after a mean of 101.8 months (7-187 months). One year allograft and patient survival after re-transplantation were 87.5% and 100% respectively (after 5 years, both were 57%). Immediate re-transplantation following early kidney transplant thrombosis can be a success. It may be considered in selected cases after allograft thrombosis.

76 FR 64963 - Re-Accreditation and Re-Approval of OMNI Hydrocarbon Measurement, Inc. as a Commercial Gauger

Science.gov (United States)

2011-10-19

..., Inc., Crosby, Texas, as a commercial gauger. SUMMARY: Notice is hereby given that, pursuant to 19 CFR 151.13, Omni Hydrocarbon Measurement, Inc., Crosby, Texas 77532, has been re- approved to gauge...

Phosphide oxides RE2AuP2O (RE = La, Ce, Pr, Nd): synthesis, structure, chemical bonding, magnetism, and 31P and 139La solid state NMR.

Science.gov (United States)

Bartsch, Timo; Wiegand, Thomas; Ren, Jinjun; Eckert, Hellmut; Johrendt, Dirk; Niehaus, Oliver; Eul, Matthias; Pöttgen, Rainer

2013-02-18

Polycrystalline samples of the phosphide oxides RE(2)AuP(2)O (RE = La, Ce, Pr, Nd) were obtained from mixtures of the rare earth elements, binary rare earth oxides, gold powder, and red phosphorus in sealed silica tubes. Small single crystals were grown in NaCl/KCl fluxes. The samples were studied by powder X-ray diffraction, and the structures were refined from single crystal diffractometer data: La(2)AuP(2)O type, space group C2/m, a = 1515.2(4), b = 424.63(8), c = 999.2(2) pm, β = 130.90(2)°, wR2 = 0.0410, 1050 F(2) values for Ce(2)AuP(2)O, and a = 1503.6(4), b = 422.77(8), c = 993.0(2) pm, β = 130.88(2)°, wR2 = 0.0401, 1037 F(2) values for Pr(2)AuP(2)O, and a = 1501.87(5), b = 420.85(5), c = 990.3(3) pm, β = 131.12(1)°, wR2 = 0.0944, 1143 F(2) values for Nd(2)AuP(2)O with 38 variables per refinement. The structures are composed of [RE(2)O](4+) polycationic chains of cis-edge-sharing ORE(4/2) tetrahedra and polyanionic strands [AuP(2)](4-), which contain gold in almost trigonal-planar phosphorus coordination by P(3-) and P(2)(4-) entities. The isolated phosphorus atoms and the P(2) pairs in La(2)AuP(2)O could clearly be distinguished by (31)P solid state NMR spectroscopy and assigned on the basis of a double quantum NMR technique. Also, the two crystallographically inequivalent La sites could be distinguished by static (139)La NMR in conjunction with theoretical electric field gradient calculations. Temperature-dependent magnetic susceptibility measurements show diamagnetic behavior for La(2)AuP(2)O. Ce(2)AuP(2)O and Pr(2)AuP(2)O are Curie-Weiss paramagnets with experimental magnetic moments of 2.35 and 3.48 μ(B) per rare earth atom, respectively. Their solid state (31)P MAS NMR spectra are strongly influenced by paramagnetic interactions. Ce(2)AuP(2)O orders antiferromagnetically at 13.1(5) K and shows a metamagnetic transition at 11.5 kOe. Pr(2)AuP(2)O orders ferromagnetically at 7.0 K.

ReSeg: A Recurrent Neural Network-Based Model for Semantic Segmentation

OpenAIRE

Visin, Francesco; Ciccone, Marco; Romero, Adriana; Kastner, Kyle; Cho, Kyunghyun; Bengio, Yoshua; Matteucci, Matteo; Courville, Aaron

2015-01-01

We propose a structured prediction architecture, which exploits the local generic features extracted by Convolutional Neural Networks and the capacity of Recurrent Neural Networks (RNN) to retrieve distant dependencies. The proposed architecture, called ReSeg, is based on the recently introduced ReNet model for image classification. We modify and extend it to perform the more challenging task of semantic segmentation. Each ReNet layer is composed of four RNN that sweep the image horizontally ...

Possibilities of radiation sterilization for re-usage of medical devices in the medical management

International Nuclear Information System (INIS)

Tabei, Masae; Kudo, Hisaaki; Katsumura, Yosuke

2004-01-01

The rule for re-usage of medical single-use devices was established in US in 2000 based on the concept of Managed Care (total management of medicare on cost, quality and patients' satisfaction) and 20-30% of those devices are re-used at present. The re-usage is conducted in not only US but also Canada, Denmark, UK, India, China etc. Standing on the viewpoint, this paper described and discussed the possibility of re-usage of the single-use devices now prohibited in Japan, possible re-sterilization, possible re-usage of hollow fiber-type hemodialyzer following γ-ray sterilization with consideration for D-values against bacteria and viruses, cost estimation of electron beam sterilization for re-usage, and radiation sterilization of waste water and plastic materials. Radiation sterilization for re-usage of medical devices was concluded possible if their materials and records for their usage processes are proper, and should be conducted in a large scale after sufficient examinations by industries/government/academia. (N.I.)

Un copiste inattendu à Vic-sur-Cère (Cantal

Directory of Open Access Journals (Sweden)

Renaud Benoit-Cattin

2012-02-01

Full Text Available A Vic-sur-Cère, petit bourg du Cantal, l’hôtel du Pont et du Parc abrite au rez-de-chaussée une salle de restaurant dont les quatre murs sont ornés de dix-sept peintures d’un caractère peu ou prou monumental. Leur hauteur est d’environ 1,50 m, leur largeur variant de 0,6 à 3,5 m. Quatorze d’entre elles ont été exécutées par Antoine Cayrol entre 1909 et 1914, les trois dernières par son petit-fils, Roger Cayrol, en 1954.Le grand-père, Antoine, né en 1864, est élevé à Paris. Après son service m...

Radiochemical study of Re/W adsorption behavior on a strongly basic anion exchange resin

International Nuclear Information System (INIS)

Gott, Matthew D.; Missouri Univ., Columbia, MO; Ballard, Beau D.; Redman, Lindsay N.

2014-01-01

Rhenium-186g is a radionuclide with a high potential for therapeutic applications. It emits therapeutic β - particles accompanied by low energy γ-rays, which allows for in-vivo tracking of the radiolabeled compound and dosimetry estimates. The current reactor production pathway 185 Re(n,γ) 186g Re produces low specific activity 186g Re, thereby limiting its therapeutic application. Work is underway to develop an accelerator-based, charged particle induced production method for high specific activity 186g Re from targets of enriched 186 W. To optimize the chemical 186g Re recovery method, batch studies have been performed to characterize the adsorption behavior of Re and W on a strongly basic anion exchange resin. An in-depth physicochemical profile was developed for the interaction of Re with resin material, which showed the reaction to be endothermic and spontaneous. Basic (NaOH) and acidic (HNO 3 ) matrices were used to determine the equilibrium distribution coefficients for Re and W. The resin exhibits the best affinity for Re at slightly basic conditions and little affinity above moderately acidic concentrations. Tungsten has low affinity for the resin above moderately basic concentrations. A study was performed to examine the effect of W concentration on Re adsorption, which showed that even a high ionic WO 4 2- strength of up to 1.9 mol kg -1 does not significantly compromise ReO 4 - retention on the resin. (orig.)

Electronic and atomic disorder in icosahedral AlPdRe

International Nuclear Information System (INIS)

Rapp, Oe; Karkin, A A; Goshchitskii, B N; Voronin, V I; Srinivas, V; Poon, S J

2008-01-01

Relations between electronic and atomic disorder of i-AlPdRe have been investigated by studies of neutron irradiated and annealed samples. The advantage with this technique is that a single sample can be monitored over a significant range of varying electronic properties, without concern for any influence of varying impurities. X-ray diffraction, the electrical resistivity and its temperature dependence, and the magnetoresistance are studied. The results show that annealings of an irradiated sample lead to improvement of the atomic order, as reflected in increased intensities of the x-ray diffraction peaks, while electronic properties change in the direction of increasing electronic disorder towards a metal-insulator transition. The observed relation in quasicrystals that improved atomic structure is associated with stronger anomalies in transport properties is thus also seen in i-AlPdRe. In particular, the variation of the diffusion constant in the region of small values of the resistivity is found to be similar for annealed polygrain samples and for single grain samples with varying Pd concentration, as evaluated from literature data, indicating a similar development of electronic disorder in both sets of samples. However, the problem remains as to why the resistivity is small in single grain samples which are atomically well-ordered. The possibility of a strong sensitivity to concentration differences is pointed out

The effects of RE and Si on the microstructure and corrosion resistance of Zn–6Al–3Mg hot dip coating

International Nuclear Information System (INIS)

Li, Shiwei; Gao, Bo; Yin, Shaohua; Tu, Ganfeng; Zhu, Guanglin; Sun, Shuchen; Zhu, Xiaoping

2015-01-01

Highlights: • ZAM coating has been prepared by using an experimental hot-dip galvanizing simulator. • The corrosion resistance of ZAM coating can be improved by additions of Si and RE. • Zn–6Al–3Mg–Si–RE coating forms a dense and stabilized corrosion product layer. • Zn–6Al–3Mg–Si–RE coating shows uniform corrosion. - Abstract: The effects of Si and RE on the microstructure and corrosion resistance of Zn–6Al–3Mg coating (ZAM) have been investigated. Surface morphology observations of the coating and corrosion products reveal that the additions of Si and rare earth metals (RES) improve the microstructural homogeneity of ZAMSR coating and stability of corrosion products formed on ZAMSR coating. Moreover, only uniform corrosion occurs in ZAMSR coating during the corrosion test, while intergranular corrosion and pitting occur in ZAM. As a result, the corrosion resistance of ZAM coating is improved by the additions of Si and RES.

The effects of RE and Si on the microstructure and corrosion resistance of Zn–6Al–3Mg hot dip coating

Energy Technology Data Exchange (ETDEWEB)

Li, Shiwei [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Gao, Bo, E-mail: surfgao@aliyun.com [School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Yin, Shaohua [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Tu, Ganfeng; Zhu, Guanglin; Sun, Shuchen; Zhu, Xiaoping [School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China)

2015-12-01

Highlights: • ZAM coating has been prepared by using an experimental hot-dip galvanizing simulator. • The corrosion resistance of ZAM coating can be improved by additions of Si and RE. • Zn–6Al–3Mg–Si–RE coating forms a dense and stabilized corrosion product layer. • Zn–6Al–3Mg–Si–RE coating shows uniform corrosion. - Abstract: The effects of Si and RE on the microstructure and corrosion resistance of Zn–6Al–3Mg coating (ZAM) have been investigated. Surface morphology observations of the coating and corrosion products reveal that the additions of Si and rare earth metals (RES) improve the microstructural homogeneity of ZAMSR coating and stability of corrosion products formed on ZAMSR coating. Moreover, only uniform corrosion occurs in ZAMSR coating during the corrosion test, while intergranular corrosion and pitting occur in ZAM. As a result, the corrosion resistance of ZAM coating is improved by the additions of Si and RES.

Accretion in Radiative Equipartition (AiRE) Disks

Energy Technology Data Exchange (ETDEWEB)

Yazdi, Yasaman K.; Afshordi, Niayesh, E-mail: yyazdi@pitp.ca, E-mail: nafshordi@pitp.ca [Perimeter Institute for Theoretical Physics, 31 Caroline Street N, Waterloo, ON N2L 2Y5 (Canada)

2017-07-01

Standard accretion disk theory predicts that the total pressure in disks at typical (sub-)Eddington accretion rates becomes radiation pressure dominated. However, radiation pressure dominated disks are thermally unstable. Since these disks are observed in approximate steady state over the instability timescale, our accretion models in the radiation-pressure-dominated regime (i.e., inner disk) need to be modified. Here, we present a modification to the Shakura and Sunyaev model, where the radiation pressure is in equipartition with the gas pressure in the inner region. We call these flows accretion in radiative equipartition (AiRE) disks. We introduce the basic features of AiRE disks and show how they modify disk properties such as the Toomre parameter and the central temperature. We then show that the accretion rate of AiRE disks is limited from above and below, by Toomre and nodal sonic point instabilities, respectively. The former leads to a strict upper limit on the mass of supermassive black holes as a function of cosmic time (and spin), while the latter could explain the transition between hard and soft states of X-ray binaries.

Taevalik trio / Laurence Lumiére

Index Scriptorium Estoniae

Lumiére, Laurence

2000-01-01

Actionfilm "Charlie inglid" : režissöör Joseph McGinty Nichol : peategelased : Drew Barrymore (. Ka produtsent), Cameron Diaz ja Lucy Liu : Ameerika Ühendriigid 2000. Ka : Nädal nr. 47, lk. 90-91

[The bonding mechanisms of base metals for metal-ceramic crown microstructure analysis of bonding agent and gold bond between porcelain and base metals].

Science.gov (United States)

Wang, C C; Hsu, C S

1996-06-01

The use of base metal alloys for porcelain fused to a metal crown and bridges has increased recently because of lower price, high hardness, high tensile strength and high elastic modulus. The addition of beryllium to base metal alloys increased fluidity and improved casting fitness. Beryllium also controlled surface oxidation and bonding strength. The bonding agent and gold bonding agent also affected the bonding strength between porcelain and metal alloys. Four commercially available ceramic base alloys were studied (two alloys contained beryllium element, another two did not). The purpose of this investigation was to study the microstructure between porcelain matrix, bonding agent and alloy matrix interfaces. A scanning electron micro-probe analyzer and energy dispersive X-ray spectroscopy (EDXS) were used to study the distribution of elements (Ni, Cr, Mo, Cu, O, Si, Sn, Al) in four base alloys. The following results were obtained: 1. The thickness of the oxidized layer of Rexillium III alloy and Unitbond alloy (contained beryllium) was thinner than Unibond alloy and Wiron 88 alloy (no beryllium). 2. The thickness of the oxidized layer of alloys in air (10 minutes and 30 minutes) was thinner in Unitbond (2.45 microns and 3.80 microns) and thicker in Wiron 88 (4.39 microns and 5.96 microns). 3. The thickness of the oxidized layer occurring for a duration of ten minutes (in vaccum) showed that the Rexillium III alloy was the thinnest (1.93 microns), and Wiron 88 alloy was the thickest (2.30 microns). But in thirty minutes (vacuum), Unitbond alloy was the thinnest (3.37 microns), and Wiron 88 alloy was the thickest (5.51 microns). 4. The intensity of Cr elements was increased obviously near the interface between Unitbond alloy, Wiron 88 alloy (no beryllium) and oxidized layer, but the intensity of Ni and Mo elements was slightly increased. The intensity of Cr element was not increased markedly between Rexillium III alloy, Unitbond alloy (beryllium) and oxidized

New quaternary indides RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} (RE = La, Nd, Sm)

Energy Technology Data Exchange (ETDEWEB)

Dominyuk, Nataliya [Lviv Univ. (Ukraine). Dept. of Inorganic Chemistry; Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Zaremba, Vasyl I. [Lviv Univ. (Ukraine). Dept. of Inorganic Chemistry; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie

2011-04-15

The quaternary indides RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} (RE = La,Nd, Sm) were synthesized from the elements by arc-melting. Single crystals were grown by slow cooling of the polycrystalline samples. The structures were characterized by powder and single-crystal X-ray diffraction: Ce{sub 7}Ni{sub 4.73}Ge{sub 3.27}In{sub 6} type, P6/m, Z = 1, a = 1147.05(9), c = 426.82(4) pm, wR2 = 0.0652, 528 F{sup 2} values for La{sub 7}Ni{sub 4.46}Ge{sub 3.54}In{sub 6}, a = 1134.5(7), c = 407.1(7) pm, wR2 = 0.0419, 441 F{sup 2} values for Nd{sub 7}Ni{sub 4.91}Ge{sub 3.09}In{sub 6}, and a = 1133.5(2), c = 404.3(1) pm, wR2 = 0.0619, 498 F{sup 2} values for Sm{sub 7}Ni{sub 4.31}Ge{sub 3.69}In{sub 6}, with 25 parameters per refinement. Characteristic features of the RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} structures are hexagonal, AlB{sub 2}-related prisms around the RE1 atoms and a tricapped, trigonalprismatic coordination of the nickel atoms. (orig.)

Our experience with radiosynoviorthesis and re-radiosynoviorthesis of knees

International Nuclear Information System (INIS)

Kraft, Otakar; Kaspsrek, Richard

2005-01-01

Full text: In this paper the authors present their experience with radiosynoviorthesis (RSO) and re-radiosynoviorthesis (re-RSO) of knees. The objectives of this study were to compare treatment results between first RSO and re-RSO. Before RSO an ultrasonography (USG), an X-ray, a three-phase bone scintigraphy (TPBS). The treatment effect (TE) can be expected if a synovitis is proved by these examinations. To knees we inject 200 MBq of the yttrium citrate. TE is evaluated by the clinical examination, USG and TPBS. If the effect of RSO is not satisfying, RSO can be repeated no sooner than 6 months later. Among our patients we have high percentage of re-RSO. A rate between single RSO and re-RSO was 11:8. From 1986 to December 2004 we treated 1267 knees with Yttrium Citrate 37.9% patients had gonarthrosis, 26.1% chronic synovitis, 20.3% rheumatoid arthritis, 4.6% relapsing fluid, 3.9% psoriatic arthropathy, 3.3% ankylozing spondylarthritis and 1.3% hemophilic arthropathy. The evaluation of TE by patients in 294 RSO (170 patients with single RSO and 124 pts with re-RSO an influence on a pain and a fluid formation after single RSO: 10.9% no influence, 42.2% substantial and long-term effect, 46.9% partial TE and after re-RSO: 8.2% no influence, 36.6% the substantial and long-term TE, 55,2% the partial TE. The best results evaluated by patients were in patients with the rheumatoid arthritis and haemophilia. Worst results were in osteoarthritis in case of considerable radiological changes. Clinical follow up of 110 pts with single RSO and 70 pts with re-RSO: after single RSO: after 6 months in 77% swelling and a filling reduction and in 86% pain reduction, after 1 year in 53% the swelling and the filling reduction and in 62% the pain reduction, after 2 yrs in 28% the swelling and the filling reduction and in 48% the pain reduction; after re-RSO: after 6 months in 62% the swelling and the filling reduction and in 75% the pain reduction, after 1 year in 43% the swelling and

Increased pulmonary vascular permeability as a cause of re-expansion edema in rabbits

International Nuclear Information System (INIS)

Pavlin, D.J.; Nessly, M.L.; Cheney, F.W.

1981-01-01

In order to study the mechanism(s) underlying re-expansion edema, we measured the concentration of labeled albumin (RISA) in the extravascular, extracellular water (EVECW) of the lung as a measure of pulmonary vascular permeability. Re-expansion edema was first induced by rapid re-expansion of rabbit lungs that had been collapsed for 1 wk by pneumothorax. The RISA in EVECW was expressed as a fraction of its plasma concentration: (RISA)L/(RISA)PL. The volume of EVECW (ml/gm dry lung) was measured using a 24 Na indicator. Results in re-expansion edema were compared with normal control lungs and with oleic acid edema as a model of permeability edema. In re-expanded lungs, EVECW (3.41 +/- SD 1.24 ml/g) and (RISA)L/(RISA)PL 0.84 +/- SD 0.15) were significantly increased when compared with normal control lungs (2.25 +/- 0.41 ml/g and 0.51 +/- 0.20, respectively). Results in oleic acid edema (5.66 +/- 2.23 ml/g and 0.84 +/- 0.23) were similar to re-expansion edema. This suggested that re-expansion edema is due to increased pulmonary vascular permeability caused by mechanical stresses applied to the lung during re-expansion

Pressure-induced phase transitions in nanocrystalline ReO3

International Nuclear Information System (INIS)

Biswas, Kanishka; Muthu, D V S; Sood, A K; Kruger, M B; Chen, B; Rao, C N R

2007-01-01

Pressure-induced phase transitions in the nanocrystals of ReO 3 with an average diameter of ∼12 nm have been investigated in detail by using synchrotron x-ray diffraction and the results compared with the literature data of bulk samples of ReO 3 . The study shows that the ambient-pressure cubic I phase (space group Pm3-barm) transforms to a monoclinic phase (space group C 2/c), then to a rhombohedral I phase (space group R3-barc), and finally to another rhombohedral phase (rhombohedral II, space group R3-barc) with increasing pressure over the 0.0-20.3 GPa range. The cubic I to monoclinic transition is associated with the largest volume change (∼5%), indicative of a reconstructive transition. The transition pressures are generally lower than those known for bulk ReO 3 . The cubic II (Im3-bar) or tetragonal (P4/mbm) phases do not occur at lower pressures. The nanocrystals are found to be more compressible than bulk ReO 3 . On decompression to ambient pressure, the structure does not revert back to the cubic I structure

Simple re-instantiation of small databases using cloud computing.

Science.gov (United States)

Tan, Tin Wee; Xie, Chao; De Silva, Mark; Lim, Kuan Siong; Patro, C Pawan K; Lim, Shen Jean; Govindarajan, Kunde Ramamoorthy; Tong, Joo Chuan; Choo, Khar Heng; Ranganathan, Shoba; Khan, Asif M

2013-01-01

Small bioinformatics databases, unlike institutionally funded large databases, are vulnerable to discontinuation and many reported in publications are no longer accessible. This leads to irreproducible scientific work and redundant effort, impeding the pace of scientific progress. We describe a Web-accessible system, available online at http://biodb100.apbionet.org, for archival and future on demand re-instantiation of small databases within minutes. Depositors can rebuild their databases by downloading a Linux live operating system (http://www.bioslax.com), preinstalled with bioinformatics and UNIX tools. The database and its dependencies can be compressed into an ".lzm" file for deposition. End-users can search for archived databases and activate them on dynamically re-instantiated BioSlax instances, run as virtual machines over the two popular full virtualization standard cloud-computing platforms, Xen Hypervisor or vSphere. The system is adaptable to increasing demand for disk storage or computational load and allows database developers to use the re-instantiated databases for integration and development of new databases. Herein, we demonstrate that a relatively inexpensive solution can be implemented for archival of bioinformatics databases and their rapid re-instantiation should the live databases disappear.

Controlled Confinement of Half-metallic 2D Electron Gas in BaTiO3/Ba2FeReO6/BaTiO3 Heterostructures: A First-principles Study

Science.gov (United States)

Saha-Dasgupta, Tanusri; Baidya, Santu; Waghmare, Umesh; Paramekanti, Arun

Using density functional theory calculations, we establish that the half-metallicity of bulk Ba2FeReO6 survives down i to 1 nm thickness in BaTiO3/Ba2FeReO6/BaTiO3 heterostructures grown along the (001) and (111) directions. The confinement of the two-dimensional (2D) electron gas in this quantum well structure arises from the suppressed hybridization between Re/Fe d states and unoccupied Ti d states, and it is further strengthened by polar fields for the (111) direction. This mechanism, distinct from the polar catastrophe, leads to an order of magnitude stronger confinement of the 2D electron gas than that at the LaAlO3/SrTiO3 interface. We further show low-energy bands of (111) heterostructure display nontrivial topological character. Our work opens up the possibility of realizing ultra-thin spintronic devices. Journal Ref: Phys. Rev. B 92, 161106(R) (2015) S.B. and T.S.D thank Department of Science and Technology, India for the support through Thematic Unit of Excellence. AP was supported by NSERC (Canada).

The Feasibility of Pellet Re-Fuelling of a Fusion Reactor

DEFF Research Database (Denmark)

Chang, Tinghong; Jørgensen, L. W.; Nielsen, P.

1980-01-01

The feasibility of re-fuelling a fusion reactor by injecting pellets of frozen hydrogen isotopes is reviewed. First a general look is taken of the dominant energy fluxes received by the pellet, the re-fuelling rate required and the relation between pellet size, injection speed and frequency...

Experimental study of the biological properties of 188Re-Hepama-1 biologic superparamagnetic nanoparticles

International Nuclear Information System (INIS)

Feng Yanlin; Tan Jiaju; Sun Jing; Wen Guanghua; Wu Xiaolian; Liang Sheng; Xia Jiaoyun

2007-01-01

Objective: To investigate a new biologic-superparamagnetic nanoparticles's characteristics of immunological activity, biological distributing in vivo, targeting and inhibiting tumor effect. Methods: The experimental group 188 Re-Hepama-l-superparamagnetic nanoparticles, and control groups, including 188 ReO 4 - , 188 Re-Hepama-1, and 188 Re-superparamagnetic nanoparticles, were set up. The distributions were measured after injection 4 h and 24 h by caudal vein of Kuming mice. The magnetic targeting experiments in vivo were clone with and without magnetic field in liver after injection in New Zealand rabbit. The inhibiting tumor effect on hepatic cancer cell lines SMMC-7721 of the above four 188 Re labeled products were measured by mono nuclear cell direct cytotoxicity assay method. Results: After injection 4 h and 24 h by vein, the liver taking was highest in group 188 Re-Hepama-l-superparamagnetic nanoparticles. The radiative activity in liver in magnetism zoo was higher than in non magnetism zoo in 188 Re- Hepama-1-superparamagnetic nanoparticles after applying magnetic field in left lobe of liver, and the ratio of in magnetism zoo to non magnetism zoo was 1.87. And the half effective inhibition radioactive concentrations (IC 50 ) in 188 Re-Hepama-l-superparamagnetic nanoparticles was one forth of 188 ReO 4 - . Conclusion: 188 Re- Hepama-l-superparamagnetic nanoparticles showed its fine stability in intro, good immunological activity and significant liver target. (authors)

The Re-Fe-S system at 1200, 1100, 1000 and 900 degree C

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

1999-01-01

Phase relations in the dry condensed phase system Fe-Re-S from 1200oC down to 900oC involve S-poor Fe-S melt with up to 0.2 at.% dissolved Re, S-rich melt with 0.3-0.4 at.% dissolved Re at 1200oC, Fe1-xS with Re contents growing from nil for troilite to 0.2 at.% for S-richer compositions, gFe wit...

Best Practices for Cloud Provider Connectivity for R&E Users

CERN Document Server

Bos, Erik-Jan; Kleist, Josva; Foster, David; CERN. Geneva. IT Department

2016-01-01

R&E Networks have been in the business of serving the needs of research and education for decades. A recent development is that more and more R&E Networks are required to support the overall business of research and education for their customers. As R&E institutes have felt the pressure from governments to become more efficient and cost-effective, their interest has turned to cloud solutions for scientific applications as well as back-end office systems. The use of clouds, both commercial and private, is increasing rapidly. Large scale connectivity with cloud providers is a rather new but important area, in which R&E Networks are trying to find their way to add value. Connectivity with commercial cloud providers nowadays is an important topic, and it is becoming crucial that advice to policy makers, decision makers and procurers is given so that over time it will lead to a coherent, scalable and increasingly cost-effective solution for connecting to cloud service providers.

Electronic and optoelectronic device applications based on ReS2

Science.gov (United States)

Liu, Erfu; Long, Mingsheng; Wang, Yaojia; Pan, Yiming; Ho, Chinghwa; Wang, Baigeng; Miao, Feng

Rhenium disulfide (ReS2) is a unique semiconducting TMD with distorted 1T structure and weak interlayer coupling. We have previously investigated its in-plane anisotropic property and electronic applications on FET and digital inverters. In this talk, we will present high responsivity phototransistors based on few-layer ReS2. Depending on the back gate voltage, source drain bias and incident optical light intensity, the maximum attainable photoresponsivity can reach as high as 88,600 A W-1, which is one of the highest value among individual two-dimensional materials with similar device structures. Such high photoresponsivity is attributed to the increased light absorption as well as the gain enhancement due to the existence of trap states in the few-layer ReS2 flakes. The existence of trap states is proved by temperature dependent transport measurements. It further enables the detection of weak signals. Our studies underscore ReS2 as a promising material for future electronic and sensitive optoelectronic applications.

THE BRIGHTENING OF Re50N: ACCRETION EVENT OR DUST CLEARING?

International Nuclear Information System (INIS)

Chiang, Hsin-Fang; Reipurth, Bo; Connelley, Michael S.; Walawender, Josh; Pessev, Peter; Geballe, T. R.; Best, William M. J.; Paegert, Martin

2015-01-01

The luminous Class I protostar HBC 494, embedded in the Orion A cloud, is associated with a pair of reflection nebulae, Re50 and Re50N, which appeared sometime between 1955 and 1979. We have found that a dramatic brightening of Re50N has taken place sometime between 2006 and 2014. This could result if the embedded source is undergoing a FUor eruption. However, the near-infrared spectrum shows a featureless very red continuum, in contrast to the strong CO bandhead absorption displayed by FUors. Such heavy veiling, and the high luminosity of the protostar, is indicative of strong accretion but seemingly not in the manner of typical FUors. We favor the alternative explanation that the major brightening of Re50N and the simultaneous fading of Re50 is caused by curtains of obscuring material that cast patterns of illumination and shadows across the surface of the molecular cloud. This is likely occurring as an outflow cavity surrounding the embedded protostar breaks through to the surface of the molecular cloud. Several Herbig–Haro objects are found in the region

THE BRIGHTENING OF Re50N: ACCRETION EVENT OR DUST CLEARING?