WorldWideScience

Sample records for memory alloys based

  1. Shape memory alloy based motor

    Indian Academy of Sciences (India)

    S V Sharma; M M Nayak; N S Dinesh

    2008-10-01

    Design and characterization of a new shape memory alloy wire based Poly Phase Motor has been reported in this paper. The motor can be used either in stepping mode or in servo mode of operation. Each phase of the motor consists of an SMA wire with a spring in series. The principle of operation of the poly phase motor is presented. The motor resembles a stepper motor in its functioning though the actuation principles are different and hence has been characterized similar to a stepper motor. The motor can be actuated in either direction with different phase sequencing methods, which are presented in this work. The motor is modelled and simulated and the results of simulations and experiments are presented. The experimental model of the motor is of dimension 150 mm square, 20 mm thick and uses SMA wire of 0·4 mm diameter and 125 mm of length in each phase.

  2. Shape Memory Alloy-Based Periodic Cellular Structures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I effort will develop and demonstrate an innovative shape memory alloy (SMA) periodic cellular structural technology. Periodic cellular structures...

  3. Microfabricated Cantilevers Based on Sputtered Thin-Film Ni50Ti50 Shape Memory Alloy (SMA)

    Science.gov (United States)

    2015-08-01

    Memory Alloy ( SMA ) by Cory R Knick and Christopher J Morris Approved for public release; distribution unlimited...Microfabricated Cantilevers Based on Sputtered Thin-Film Ni50Ti50 Shape Memory Alloy ( SMA ) by Cory R Knick and Christopher J Morris Sensors...2014 – 05/2015 4. TITLE AND SUBTITLE Microfabricated Cantilevers Based on Sputtered Thin-Film Ni50Ti50 Shape Memory Alloy ( SMA ) 5a. CONTRACT NUMBER

  4. Shape Memory Alloy-Based Periodic Cellular Structures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase II effort will continue to develop and demonstrate an innovative shape memory alloy (SMA) periodic cellular structural technology. Periodic cellular...

  5. Several Issues in the Development of Ti-Nb-Based Shape Memory Alloys

    Science.gov (United States)

    Kim, Hee Young; Miyazaki, Shuichi

    2016-12-01

    Ni-free Ti-based shape memory alloys, particularly Ti-Nb-based alloys, have attracted increasing attraction since the early 2000s due to their wide application potentials in biomedical fields. Recently, there has been significant progress in understanding the martensitic transformation behavior of Ti-Nb-based alloys and many novel superelastic alloys have been developed. The superelastic properties of Ti-Nb-based alloys have been remarkably improved through the optimization of alloying elements and microstructure control. In this paper, in order to explore and establish the alloy design strategy, several important issues in the development of Ti-Nb-based shape memory alloys are reviewed. Particularly, the effects of alloying elements on the martensitic transformation temperature and the transformation strain are analyzed. The effects of omega phase and texture on the superelastic properties are also discussed.

  6. Properties and Application of Iron-based Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Li Jian-chen; Jiang Qing; Dai Jun

    2005-01-01

    The properties of FeMnSiCrNi shape memory alloy were investigated. The results show that the best shape memory effect of Fel4Mn6Si9Cr5Ni alloy is 85%. The transformation amount of the ε→γ transformation is not complete after heating the alloy to 1000 K, As and Af points drop with increased transformation enthalpy ( △Hγ→ε) by thermal cycling and increased prestrain. The alloy shows also good creep and stress relaxation resistance. In addition, the alloy having a tensile force of 20 kN and a sealing pressure of 6 MPa can satisfy requirements for possible industrial application on pipe joints.

  7. A Shape Memory Alloy Based Cryogenic Thermal Conduction Switch

    Science.gov (United States)

    Notardonato, W. U.; Krishnan, V. B.; Singh, J. D.; Woodruff, T. R.; Vaidyanathan, R.

    2005-01-01

    Shape memory alloys (SMAs) can produce large strains when deformed (e.g., up to 8%). Heating results in a phase transformation and associated recovery of all the accumulated strain. This strain recovery can occur against large forces, resulting in their use as actuators. Thus an SMA element can integrate both sensory and actuation functions, by inherently sensing a change in temperature and actuating by undergoing a shape change as a result of a temperature-induced phase transformation. Two aspects of our work on cryogenic SMAs are addressed here. First - a shape memory alloy based cryogenic thermal conduction switch for operation between dewars of liquid methane and liquid oxygen in a common bulkhead arrangement is discussed. Such a switch integrates the sensor element and the actuator element and can be used to create a variable thermal sink to other cryogenic tanks for liquefaction, densification, and zero boil-off systems for advanced spaceport applications. Second - fabrication via arc-melting and subsequent materials testing of SMAs with cryogenic transformation temperatures for use in the aforementioned switch is discussed.

  8. Performance of a base isolator with shape memory alloy bars

    Institute of Scientific and Technical Information of China (English)

    Fabio Casciati; Lucia Faravelli; Karim Hamdaoui

    2007-01-01

    A new and innovative base isolation device is introduced in this paper based on extensive research carried out by the authors and their co-workers.A prototype of the device was built and experimentally tested on the shaking table.The new base isolation device consists of two disks,one vertical cylinder with an upper enlargement sustained by three horizontal cantilevers,and at least three inclined shape memory alloy(SMA) bars.The role of the SMA bars is to limit the relative motion between the base and the superstructure,to dissipate energy by their super-elastic constitutive law and to guarantee the re-centring of the device.To verify the expected performance,a prototype was built and tested under sinusoidal waves of displacement of increasing frequency with different amplitudes.It is shown that the main feature of the proposed base isolation device is that for cyclic loading,the super-elastic behavior of the alloy results in wide load-displacement loops,where a large amount of energy is dissipated.

  9. Oligocrystalline shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ueland, Stian M.; Chen, Ying; Schuh, Christopher A. [Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States)

    2012-05-23

    Copper-based shape memory alloys (SMAs) exhibit excellent shape memory properties in single crystalline form. However, when they are polycrystalline, their shape memory properties are severely compromised by brittle fracture arising from transformation strain incompatibility at grain boundaries and triple junctions. Oligocrystalline shape memory alloys (oSMAs) are microstructurally designed SMA structures in which the total surface area exceeds the total grain boundary area, and triple junctions can even be completely absent. Here it is shown how an oligocrystalline structure provides a means of achieving single crystal-like SMA properties without being limited by constraints of single crystal processing. Additionally, the formation of oSMAs typically involves the reduction of the size scale of specimens, and sample size effects begin to emerge. Recent findings on a size effect on the martensitic transformation in oSMAs are compared and a new regime of heat transfer associated with the transformation heat evolution in these alloys is discussed. New results on unassisted two-way shape memory and the effect of loading rate in oSMAs are also reported. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  10. Shape Memory Alloy (SMA)-Based Launch Lock

    Science.gov (United States)

    Badescu, Mircea; Bao, Xiaoqi; Bar-Cohen, Yoseph

    2014-01-01

    Most NASA missions require the use of a launch lock for securing moving components during the launch or securing the payload before release. A launch lock is a device used to prevent unwanted motion and secure the controlled components. The current launch locks are based on pyrotechnic, electro mechanically or NiTi driven pin pullers and they are mostly one time use mechanisms that are usually bulky and involve a relatively high mass. Generally, the use of piezoelectric actuation provides high precession nanometer accuracy but it relies on friction to generate displacement. During launch, the generated vibrations can release the normal force between the actuator components allowing shaft's free motion which could result in damage to the actuated structures or instruments. This problem is common to other linear actuators that consist of a ball screw mechanism. The authors are exploring the development of a novel launch lock mechanism that is activated by a shape memory alloy (SMA) material ring, a rigid element and an SMA ring holding flexure. The proposed design and analytical model will be described and discussed in this paper.

  11. Shape Memory Alloy (SMA)-Based Launch Lock

    Science.gov (United States)

    Badescu, Mircea; Bao, Xiaoqi; Bar-Cohen, Yoseph

    2014-01-01

    Most NASA missions require the use of a launch lock for securing moving components during the launch or securing the payload before release. A launch lock is a device used to prevent unwanted motion and secure the controlled components. The current launch locks are based on pyrotechnic, electro mechanically or NiTi driven pin pullers and they are mostly one time use mechanisms that are usually bulky and involve a relatively high mass. Generally, the use of piezoelectric actuation provides high precession nanometer accuracy but it relies on friction to generate displacement. During launch, the generated vibrations can release the normal force between the actuator components allowing shaft's free motion which could result in damage to the actuated structures or instruments. This problem is common to other linear actuators that consist of a ball screw mechanism. The authors are exploring the development of a novel launch lock mechanism that is activated by a shape memory alloy (SMA) material ring, a rigid element and an SMA ring holding flexure. The proposed design and analytical model will be described and discussed in this paper.

  12. Shape-Memory-Alloy-Based Deicing System Developed

    Science.gov (United States)

    1996-01-01

    Ice buildup on aircraft leading edge surfaces has historically been a problem. Most conventional deicing systems rely either on surface heating to melt the accreted ice or pneumatic surface inflation to mechanically debond the ice. Deicers that rely solely on surface heating require large amounts of power. Pneumatic deicers usually cannot remove thin layers of ice and lack durability. Thus, there is a need for an advanced, low-power ice protection system. As part of the NASA Small Business and Innovation Research (SBIR) program, Innovative Dynamics, Inc., developed an aircraft deicing system that utilizes the properties of Shape Memory Alloys (SMA). The SMA-based system has achieved promising improvements in energy efficiency and durability over more conventional deicers. When they are thermally activated, SMA materials change shape; this is analogous to a conventional thermal expansion. The thermal input is currently applied via conventional technology, but there are plans to implement a passive thermal input that is supplied from the energy transfer due to the formation of the ice itself. The actively powered deicer was tested in the NASA Lewis Icing Research Tunnel on a powered rotating rig in early 1995. The system showed promise, deicing both rime and glaze ice shapes as thin as 1/8 in. The first prototype SMA deicer reduced power usage by 45 percent over existing electrothermal systems. This prototype system was targeted for rotorcraft system development. However, there are current plans underway to develop a fixed-wing version of the deicer.

  13. A Gradient-Based Constitutive Model for Shape Memory Alloys

    Science.gov (United States)

    Tabesh, Majid; Boyd, James; Lagoudas, Dimitris

    2017-06-01

    Constitutive models are necessary to design shape memory alloy (SMA) components at nano- and micro-scales in NEMS and MEMS. The behavior of small-scale SMA structures deviates from that of the bulk material. Unfortunately, this response cannot be modeled using conventional constitutive models which lack an intrinsic length scale. At small scales, size effects are often observed along with large gradients in the stress or strain. Therefore, a gradient-based thermodynamically consistent constitutive framework is established. Generalized surface and body forces are assumed to contribute to the free energy as work conjugates to the martensite volume fraction, transformation strain tensor, and their spatial gradients. The rates of evolution of these variables are obtained by invoking the principal of maximum dissipation after assuming a transformation surface, which is a differential equation in space. This approach is compared to the theories that use a configurational force (microforce) balance law. The developed constitutive model includes energetic and dissipative length scales that can be calibrated experimentally. Boundary value problems, including pure bending of SMA beams and simple torsion of SMA cylindrical bars, are solved to demonstrate the capabilities of this model. These problems contain the differential equation for the transformation surface as well as the equilibrium equation and are solved analytically and numerically. The simplest version of the model, containing only the additional gradient of martensite volume fraction, predicts a response with greater transformation hardening for smaller structures.

  14. Relationship between phase composition and corrosion resistanceof Ni-Ti-Nb based shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The stability and microstructure of Ni-Ti-Nb based shape memory alloys were investigated after alloyed with elements Zr, Cr and V. In artificial seawater (3.5%NaCl) and physiological solution (5%NaCl+0.1%H2O2), the results show that the alloying elements influence the corrosion behavior of Ni-Ti-Nb alloys. Generally, Zr improves the corrosion resistance of Ni-Ti-Nb alloy, Cr reduces its corrosion resistance and V does not change the property. In order to investigate the reason of the difference,the relation of the phase components and corrosion resistance of Ni-Ti-Nb based shape memory alloys were studied by element analysis and SEM.

  15. Study on hemocompatibility and corrosion behavior of ion implanted TiNi shape memory alloy and Co-based alloys.

    Science.gov (United States)

    Liang, Chenghao; Huang, Naibao

    2007-10-01

    Biomedical TiNi shape memory alloy and Co-based alloys were ion implanted, and corrosion resistance and hemocompatibility of these had been investigated with electrochemical method, dynamic clotting time, and hemolysis rate tests. The results indicated that the electrochemical stability and anodic polarization behavior of the materials were improved significantly after ion implantation. When TiNi, Co-based alloys were implanted Mo + C and Ti + C, respectively, the corrosion potentials were enhanced more than 200 mV, passive current densities decreased, and passive ranges were broadened. Dynamic clotting time of the ion implanted substances was prolonged and hemolysis rate decreased. All the results pointed out that corrosion resistance and hemocompatibility of the alloys were improved by ion implantation, and effects of dual implantation was better than that of C single implantation. X-ray diffraction analysis of the alloys after dual implantation revealed that TiC, Mo(2)C, Mo(9)Ti(4), and Mo appeared on the surface of TiNi alloy, and CoC(x), Co(3)Ti, TiC, and TiO on the surface of Co-based alloys. These phases dispersing on the alloy surface formed amorphous film, prevented dissolving of alloy elements and improved the corrosion resistance and hemocompatibility of the alloys.

  16. Effect of solution hardening on the shape memory effect of Fe-Mn based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Tsuzaki, K.; Natsume, Y.; Maki, T. [Kyoto Univ. (Japan). Dept. of Materials Science and Engineering; Tomota, Y. [Ibaraki Univ., Hitachi (Japan)

    1995-10-01

    Fe-high Mn-Si alloys, which undergo {gamma} (fcc) to {var_epsilon} (hcp) martensitic transformation, exhibit a pronounced shape memory effect. The origin of shape memory effect of these alloys is the reversion of stress-induced {var_epsilon} martensite. A shape change must hence be accomplish3ed by stress-induced martensitic transformation without permanent slip in austenite ({gamma}) in order to obtain a good shape memory effect. It is clear that the intrusion of permanent slip can be suppressed by increasing the strength of austenite and by decreasing the applied stress required for a shape change due to stress-induced martensitic transformation. It has been reported that the addition of the interstitial elements of C and N as well as the substitutional elements of Mo and V increases the 0.2% proof stress of austenite in Fe-high Mn alloys. However, there have been few studies on the effect of these alloying elements on the shape memory effect of Fe-high Mn based alloys. In the present study, it was aimed to improve the shape memory effect of Fe-high Mn based alloys by the strengthening of austenite through solution hardening due to C and Mo.

  17. Microstructural Analysis of Ti-Based Shape Memory Alloys Following the Electrochemical Corrosion in Artificial Saliva

    Science.gov (United States)

    Baciu, C.; Baciu, E. R.; Cimpoeșu, R.; Levente, C. G.; Bosinceanu, D. G.; Baciu, M.; Bejinariu, C.

    2017-06-01

    The investigations carried out aimed to highlight the structural modifications occurred in the Ti-based shape memory alloys subject to electrocorrosion in Afnor artificial saliva. The behavior to corrosion was highlighted by fast electrochemical tests, mainly by dynamic potentiometry. From the microstructural analysis we noticed that the specimens of the two Ti-based shape memory alloys show traces of “pitting” corrosion on their surface of diverse sizes, a fact that will raise issues in terms of cytotoxicity due to the corrosion products released.

  18. Formation Mechanism of Curved Martensite Structures in Cu-based Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The curved martensite structures have been observed in CuZnAl-based shape memory alloys by both transmission electron microscope and optical microscope. It was found that the curved martensite structures observed in as-solution treated, as-aged and as-trained alloys usually occurred around dislocation tangles or precipitate, at the plate boundary or grain boundary, and when the growing plates collided with each other or alternate mutually.

  19. Martensitic transformation and related magnetic effects in Ni-Mn-based ferromagnetic shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    Wang Dun-Hui; Han Zhi-Da; Xuan Hai-Cheng; Ma Sheng-Can; Chen Shui-Yuan; Zhang Cheng-Liang; Du You-Wei

    2013-01-01

    Ferromagnetic shape memory alloys,which undergo the martensitic transformation,are famous multifunctional materials.They exhibit many interesting magnetic properties around the martensitic transformation temperature due to the strong coupling between magnetism and structure.Tuning magnetic phase transition and optimizing the magnetic effects in these alloys are of great importance.In this paper,the regulation of martensitic transformation and the investigation of some related magnetic effects in Ni-Mn-based alloys are reviewed based on our recent research results.

  20. Shape memory alloys. Ultralow-fatigue shape memory alloy films.

    Science.gov (United States)

    Chluba, Christoph; Ge, Wenwei; Lima de Miranda, Rodrigo; Strobel, Julian; Kienle, Lorenz; Quandt, Eckhard; Wuttig, Manfred

    2015-05-29

    Functional shape memory alloys need to operate reversibly and repeatedly. Quantitative measures of reversibility include the relative volume change of the participating phases and compatibility matrices for twinning. But no similar argument is known for repeatability. This is especially crucial for many future applications, such as artificial heart valves or elastocaloric cooling, in which more than 10 million transformation cycles will be required. We report on the discovery of an ultralow-fatigue shape memory alloy film system based on TiNiCu that allows at least 10 million transformation cycles. We found that these films contain Ti2Cu precipitates embedded in the base alloy that serve as sentinels to ensure complete and reproducible transformation in the course of each memory cycle. Copyright © 2015, American Association for the Advancement of Science.

  1. Identification of epsilon martensite in a Fe-based shape memory alloy by means of EBSD.

    Science.gov (United States)

    Verbeken, K; Van Caenegem, N; Raabe, D

    2009-01-01

    Ferrous shape memory alloys (SMAs) are often thought to become a new, important group of SMAs. The shape memory effect in these alloys is based on the reversible, stress-induced martensitic transformation of austenite to epsilon martensite. The identification and quantification of epsilon martensite is crucial when evaluating the shape memory behaviour of this material. Previous work displayed that promising results were obtained when studying the evolution of the amount of epsilon martensite after different processing steps with Electron BackScatter Diffraction (EBSD). The present work will discuss in detail, on the one hand, the challenges and opportunities arising during the identification of epsilon martensite by means of EBSD and, on the other hand, the possible interpretations that might be given to these findings. It will be illustrated that although the specific nature of the austenite to epsilon martensite transformation can still cause some points of discussion, EBSD has a high potential for identifying epsilon martensite.

  2. Shape Memory Alloy Actuator

    Science.gov (United States)

    Baumbick, Robert J. (Inventor)

    2002-01-01

    The present invention discloses and teaches a unique, remote optically controlled micro actuator particularly suitable for aerospace vehicle applications wherein hot gas, or in the alternative optical energy, is employed as the medium by which shape memory alloy elements are activated. In gas turbine powered aircraft the source of the hot gas may be the turbine engine compressor or turbine sections.

  3. Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Deexith Reddy

    2016-07-01

    Full Text Available Shape memory alloys (SMAs are metals that "remember" their original shapes. SMAs are useful for such things as actuators which are materials that "change shape, stiffness, position, natural frequency, and other mechanical characteristics in response to temperature or electromagnetic fields" The potential uses for SMAs especially as actuators have broadened the spectrum of many scientific fields. The study of the history and development of SMAs can provide an insight into a material involved in cutting-edge technology. The diverse applications for these metals have made them increasingly important and visible to the world. This paper presents the working of shape memory alloys , the phenomenon of super-elasticity and applications of these alloys.

  4. Variational prediction of the mechanical behavior of shape memory alloys based on thermal experiments

    Science.gov (United States)

    Junker, Philipp; Jaeger, Stefanie; Kastner, Oliver; Eggeler, Gunther; Hackl, Klaus

    2015-07-01

    In this work, we present simulations of shape memory alloys which serve as first examples demonstrating the predicting character of energy-based material models. We begin with a theoretical approach for the derivation of the caloric parts of the Helmholtz free energy. Afterwards, experimental results for DSC measurements are presented. Then, we recall a micromechanical model based on the principle of the minimum of the dissipation potential for the simulation of polycrystalline shape memory alloys. The previously determined caloric parts of the Helmholtz free energy close the set of model parameters without the need of parameter fitting. All quantities are derived directly from experiments. Finally, we compare finite element results for tension tests to experimental data and show that the model identified by thermal measurements can predict mechanically induced phase transformations and thus rationalize global material behavior without any further assumptions.

  5. Point defects behavior in beta Cu-based shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Romero, R.; Somoza, A. [Univ. Nacional del Centro de la Provincia de Buenos Aires, Tandil (Argentina). IFIMAT

    1999-12-15

    A summary of positron annihilation spectroscopy data relating to the point defect behavior after quenching and to thermal equilibrium in {beta}-phase Cu-based shape memory alloys Cu-Zn-Al and Cu-Al-Be is presented. Particular attention is given to the initial concentration of quenched-in vacancies as a function of the quenching temperature, migration of the retained point defects with aging temperature and time, and the vacancy formation and migration energies. (orig000.

  6. An Experimental Study on Rate-sensitive Tensile Deformation Behaviour of Fe-based Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Iwamoto Takeshi

    2015-01-01

    Full Text Available Recently, it is attempted to apply high manganese steel including Fe-based shape memory alloy to vibration dampers. Especially, the alloy indicates a special characteristic as a well-known shape memory effect. By coupling between this effect and its plastic deformation, it can be considered that its deformation behaviour at higher deformation rate becomes quite complicated and still unclear. In this study, tensile tests of Fe-based shape memory alloy at different rate of deformation are conducted by using two different testing apparatuses such as the conventional material testing machine and impact testing machine based on the split Hopkinson pressure bar technique. In the tests, temperature rise is captured during the quasi-static deformation. After the quasi-static test, the recovery strain due to shape memory effect is measured by heating up the deformed specimens to Af temperature. Finally, the rate sensitivity of the alloy is discussed including the recovery strain.

  7. Shape-Memory Effect and Pseudoelasticity in Fe-Mn-Based Alloys

    Science.gov (United States)

    La Roca, P.; Baruj, A.; Sade, M.

    2016-12-01

    Several Fe-based alloys are being considered as potential candidates for applications which require shape-memory behavior or superelastic properties. The possibility of using fabrication methods which are well known in the steel industry is very attractive and encourages a large amount of research in the field. In the present article, Fe-Mn-based alloys are mainly addressed. On the one hand, attention is paid to the shape-memory effect where the alloys contain (a) a maximum amount of Mn up to around 30 wt%, (b) several possible substitutional elements like Si, Cr, Ni, Co, and Nb and (c) some possible interstitial elements like C. On the other hand, superelastic alloys are analyzed, mainly the Fe-Mn-Al-Ni system discovered a few years ago. The most noticeable properties resulting from the martensitic transformations which are responsible for the mentioned properties, i.e., the fcc-hcp in the first case and the bcc-fcc in the latter are discussed. Selected potential applications are also analyzed.

  8. Shape-Memory Effect and Pseudoelasticity in Fe-Mn-Based Alloys

    Science.gov (United States)

    La Roca, P.; Baruj, A.; Sade, M.

    2017-03-01

    Several Fe-based alloys are being considered as potential candidates for applications which require shape-memory behavior or superelastic properties. The possibility of using fabrication methods which are well known in the steel industry is very attractive and encourages a large amount of research in the field. In the present article, Fe-Mn-based alloys are mainly addressed. On the one hand, attention is paid to the shape-memory effect where the alloys contain (a) a maximum amount of Mn up to around 30 wt%, (b) several possible substitutional elements like Si, Cr, Ni, Co, and Nb and (c) some possible interstitial elements like C. On the other hand, superelastic alloys are analyzed, mainly the Fe-Mn-Al-Ni system discovered a few years ago. The most noticeable properties resulting from the martensitic transformations which are responsible for the mentioned properties, i.e., the fcc-hcp in the first case and the bcc-fcc in the latter are discussed. Selected potential applications are also analyzed.

  9. Fabrication of silicon-based shape memory alloy micro-actuators

    Science.gov (United States)

    Johnson, A. David; Busch, John D.; Ray, Curtis A.; Sloan, Charles L.

    1992-01-01

    Thin film shape memory alloy has been integrated with silicon in a new actuation mechanism for microelectromechanical systems. This paper compares nickel-titanium film with other actuators, describes recent results of chemical milling processes developed to fabricate shape memory alloy microactuators in silicon, and describes simple actuation mechanisms which have been fabricated and tested.

  10. Shape memory alloy actuator

    Science.gov (United States)

    Varma, Venugopal K.

    2001-01-01

    An actuator for cycling between first and second positions includes a first shaped memory alloy (SMA) leg, a second SMA leg. At least one heating/cooling device is thermally connected to at least one of the legs, each heating/cooling device capable of simultaneously heating one leg while cooling the other leg. The heating/cooling devices can include thermoelectric and/or thermoionic elements.

  11. Shape memory alloy flexures

    Energy Technology Data Exchange (ETDEWEB)

    Bellouard, Yves; Clavel, Reymond

    2003-07-25

    Flexures are used in precision engineering where highly accurate, wear-free, smooth and repeatable motion is desired. Flexures are based on deformation of material to achieve a motion between elastically joined parts. They are used in a variety of precision mechanisms such as high-resolution balances or high accuracy optical positioning stages. Shape memory alloys (SMA) are an attractive option in designing flexures. Superelastic flexures can withstand larger deformations for the same weight as a conventional flexure. In addition, the damping properties of SMA, controllable through the phase transformation, offer new design opportunities for adaptive compliant mechanisms. The martensitic phase transformation can also be used to shift the natural frequency of flexures adding useful functionalities such as vibration rejection. This paper presents design principles of SMA flexures based on non-linear beam theory. Results show a good agreement between measured and predicted data. In addition, experimental results on phase transformation effects on damping behavior are also presented. Both, natural-frequency shift and increased damping were observed in bulk-micro machined flexures using the R-phase transformation. These results demonstrate the feasibility of natural-frequency-tunable flexures.

  12. Relationship among grain size, annealing twins and shape memory effect in Fe-Mn-Si based shape memory alloys

    Science.gov (United States)

    Wang, Gaixia; Peng, Huabei; Zhang, Chengyan; Wang, Shanling; Wen, Yuhua

    2016-07-01

    In order to clarify the relationship among grain size, annealing twins and the shape memory effect in Fe-Mn-Si based shape memory alloys, the Fe-21.63Mn-5.60Si-9.32Cr-5.38Ni (weight %) alloy with a grain size ranging from 48.9 μm-253.6 μm was obtained by adjusting the heating temperature or heating time after 20% cold-rolling. The densities of grain boundaries and annealing twins increase with a decrease in grain size, whereas the volume fraction and width of stress-induced ɛ martensite after 9% deformation at Ms + 10 K decrease. This result indicates that grain refinement raises the constraint effects of grain boundaries and annealing twins upon martensitic transformation. In this case, the ability to suppress the plastic deformation and facilitate the stress-induced ɛ martensite transformation deteriorates after grain refinement owing to the enhancement of the constraint effects. It is demonstrated by the result that the difference at Ms + 10 K between the critical stress for plastic yielding and that for inducing martensitic transformation is smaller for the specimen with a grain size of 48.9 μm than for the specimen with a grain size of 253.6 μm. Therefore, the shape memory effect declined by decreasing the grain size.

  13. Feedforward-feedback hybrid control for magnetic shape memory alloy actuators based on the Krasnosel'skii-Pokrovskii model.

    Directory of Open Access Journals (Sweden)

    Miaolei Zhou

    Full Text Available As a new type of smart material, magnetic shape memory alloy has the advantages of a fast response frequency and outstanding strain capability in the field of microdrive and microposition actuators. The hysteresis nonlinearity in magnetic shape memory alloy actuators, however, limits system performance and further application. Here we propose a feedforward-feedback hybrid control method to improve control precision and mitigate the effects of the hysteresis nonlinearity of magnetic shape memory alloy actuators. First, hysteresis nonlinearity compensation for the magnetic shape memory alloy actuator is implemented by establishing a feedforward controller which is an inverse hysteresis model based on Krasnosel'skii-Pokrovskii operator. Secondly, the paper employs the classical Proportion Integration Differentiation feedback control with feedforward control to comprise the hybrid control system, and for further enhancing the adaptive performance of the system and improving the control accuracy, the Radial Basis Function neural network self-tuning Proportion Integration Differentiation feedback control replaces the classical Proportion Integration Differentiation feedback control. Utilizing self-learning ability of the Radial Basis Function neural network obtains Jacobian information of magnetic shape memory alloy actuator for the on-line adjustment of parameters in Proportion Integration Differentiation controller. Finally, simulation results show that the hybrid control method proposed in this paper can greatly improve the control precision of magnetic shape memory alloy actuator and the maximum tracking error is reduced from 1.1% in the open-loop system to 0.43% in the hybrid control system.

  14. Feedforward-feedback hybrid control for magnetic shape memory alloy actuators based on the Krasnosel'skii-Pokrovskii model.

    Science.gov (United States)

    Zhou, Miaolei; Zhang, Qi; Wang, Jingyuan

    2014-01-01

    As a new type of smart material, magnetic shape memory alloy has the advantages of a fast response frequency and outstanding strain capability in the field of microdrive and microposition actuators. The hysteresis nonlinearity in magnetic shape memory alloy actuators, however, limits system performance and further application. Here we propose a feedforward-feedback hybrid control method to improve control precision and mitigate the effects of the hysteresis nonlinearity of magnetic shape memory alloy actuators. First, hysteresis nonlinearity compensation for the magnetic shape memory alloy actuator is implemented by establishing a feedforward controller which is an inverse hysteresis model based on Krasnosel'skii-Pokrovskii operator. Secondly, the paper employs the classical Proportion Integration Differentiation feedback control with feedforward control to comprise the hybrid control system, and for further enhancing the adaptive performance of the system and improving the control accuracy, the Radial Basis Function neural network self-tuning Proportion Integration Differentiation feedback control replaces the classical Proportion Integration Differentiation feedback control. Utilizing self-learning ability of the Radial Basis Function neural network obtains Jacobian information of magnetic shape memory alloy actuator for the on-line adjustment of parameters in Proportion Integration Differentiation controller. Finally, simulation results show that the hybrid control method proposed in this paper can greatly improve the control precision of magnetic shape memory alloy actuator and the maximum tracking error is reduced from 1.1% in the open-loop system to 0.43% in the hybrid control system.

  15. Characterization of Sputtered Nickel-Titanium (NiTi) Stress and Thermally Actuated Cantilever Bimorphs Based on NiTi Shape Memory Alloy (SMA)

    Science.gov (United States)

    2015-11-01

    Actuated Cantilever Bimorphs Based on NiTi Shape Memory Alloy ( SMA ) by Merric D Srour, Cory R Knick, and Christopher J Morris...Actuated Cantilever Bimorphs Based on NiTi Shape Memory Alloy ( SMA ) by Merric D Srour, Cory R Knick, and Christopher J Morris Sensors and...Shape Memory Alloy ( SMA ) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Merric D Srour, Cory R Knick, and

  16. Shape memory alloy thaw sensors

    Science.gov (United States)

    Shahinpoor, Mohsen; Martinez, David R.

    1998-01-01

    A sensor permanently indicates that it has been exposed to temperatures exceeding a critical temperature for a predetermined time period. An element of the sensor made from shape memory alloy changes shape when exposed, even temporarily, to temperatures above the Austenitic temperature of the shape memory alloy. The shape change of the SMA element causes the sensor to change between two readily distinguishable states.

  17. Reconciling viability and cost-effective shape memory alloy options – A review of copper and iron based shape memory metallic systems

    Directory of Open Access Journals (Sweden)

    Kenneth Kanayo Alaneme

    2016-09-01

    Full Text Available Shape memory alloys (SMAs are group of alloys that display anthropomorphic characteristics. These alloys recover their pre-deformed morphology when heated above their transition temperatures after being deformed in their lower temperature phase (martensitic phase. This unique material behavior is explored in industrial and technological applications where capacity for strain recovery is a key design parameter. Copper and iron based SMAs are largely viewed as potential cost effective substitute to Ni–Ti SMAs judging from their promising shape memory properties, damping capacity and other functional properties. Despite their outstanding potentials, the susceptibility of copper based SMAS to phase stabilization, transition hysteresis, aging and brittleness creates doubt on the possibility of transiting from the realm of potential to functional long term use in engineering applications. On the other hand the low percentage shape recovery in the Fe based SMAs also creates a gap between the theory and potential use of these alloys. This paper takes a critical look at the science of shape memory phenomena as applicable to copper and iron based SMA systems. It also covers the limitations of these systems, the effect of processing parameters on these alloys, proposed solutions to limitations associated with this group of shape memory alloys and thoughts for future consideration.

  18. Sn-Sb-Se based binary and ternary alloys for phase change memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Kyung-Min

    2008-10-28

    In this work, the effect of replacing Ge by Sn and Te by Se was studied for a systematic understanding and prediction of new potential candidates for phase change random access memories applications. The temperature dependence of the electrical/structural properties and crystallization kinetics of the Sn-Se based binary and Sn-Sb-Se based ternary alloys were determined and compared with those of the GeTe and Ge-Sb-Te system. The temperature dependence of electrical and structural properties were investigated by van der Pauw measurements, X-ray diffraction, X-ray reflectometry. By varying the heating rate, the Kissinger analysis has been used to determine the combined activation barrier for crystallization. To screen the kinetics of crystallization, a static laser tester was employed. In case of binary alloys of the type Sn{sub x}Se{sub 1-x}, the most interesting candidate is SnSe{sub 2} since it crystallizes into a single crystalline phase and has high electrical contrast and reasonably high activation energy for crystallization. In addition, the SnSe{sub 2}-Sb{sub 2}Se{sub 3} pseudobinary alloy system also might be sufficient for data retention due to their higher transition temperature and activation energy for crystallization in comparison to GeTe-Sb{sub 2}Te{sub 3} system. Furthermore, SnSe{sub 2}-Sb{sub 2}Se{sub 3} pseudobinary alloys have a higher crystalline resistivity. The desired rapid crystallization speed can be obtained for Sn{sub 1}Sb{sub 2}Se{sub 5} and Sn{sub 2}Sb{sub 2}Se{sub 7} alloys. (orig.)

  19. A lightweight shape-memory magnesium alloy.

    Science.gov (United States)

    Ogawa, Yukiko; Ando, Daisuke; Sutou, Yuji; Koike, Junichi

    2016-07-22

    Shape-memory alloys (SMAs), which display shape recovery upon heating, as well as superelasticity, offer many technological advantages in various applications. Those distinctive behaviors have been observed in many polycrystalline alloy systems such as nickel titantium (TiNi)-, copper-, iron-, nickel-, cobalt-, and Ti-based alloys but not in lightweight alloys such as magnesium (Mg) and aluminum alloys. Here we present a Mg SMA showing superelasticity of 4.4% at -150°C and shape recovery upon heating. The shape-memory properties are caused by reversible martensitic transformation. This Mg alloy includes lightweight scandium, and its density is about 2 grams per cubic centimeter, which is one-third less than that of practical TiNi SMAs. This finding raises the potential for development and application of lightweight SMAs across a number of industries.

  20. Shape memory alloy-based small crawling robots inspired by C. elegans

    Energy Technology Data Exchange (ETDEWEB)

    Yuk, Hyunwoo; Kim, Daeyeon; Shin, Jennifer H [Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon (Korea, Republic of); Lee, Honggu; Jo, Sungho, E-mail: shjo@kaist.ac.kr, E-mail: j_shin@kaist.ac.kr [Department of Computer Science, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon (Korea, Republic of)

    2011-12-15

    Inspired by its simple musculature, actuation and motion mechanisms, we have developed a small crawling robot that closely mimics the model organism of our choice: Caenorhabditis elegans. A thermal shape memory alloy (SMA) was selected as an actuator due to the similarities of its properties to C. elegans muscles. Based on the anatomy of C. elegans, a 12-unit robot was designed to generate a sinusoidal undulating motion. Each body unit consisting of a pair of SMA actuators is serially connected by rigid links with an embedded motion control circuit. A simple binary operation-based motion control mechanism was implemented using a microcontroller. The assembled robot can execute C. elegans-like motion with a 0.17 Hz undulation frequency. Its motion is comparable to that of a real worm.

  1. Shape memory alloy-based small crawling robots inspired by C. elegans.

    Science.gov (United States)

    Yuk, Hyunwoo; Kim, Daeyeon; Lee, Honggu; Jo, Sungho; Shin, Jennifer H

    2011-12-01

    Inspired by its simple musculature, actuation and motion mechanisms, we have developed a small crawling robot that closely mimics the model organism of our choice: Caenorhabditis elegans. A thermal shape memory alloy (SMA) was selected as an actuator due to the similarities of its properties to C. elegans muscles. Based on the anatomy of C. elegans, a 12-unit robot was designed to generate a sinusoidal undulating motion. Each body unit consisting of a pair of SMA actuators is serially connected by rigid links with an embedded motion control circuit. A simple binary operation-based motion control mechanism was implemented using a microcontroller. The assembled robot can execute C. elegans-like motion with a 0.17 Hz undulation frequency. Its motion is comparable to that of a real worm.

  2. Impact of Different Electrical Time-Based Activations on NiTi Shape Memory Alloys

    Science.gov (United States)

    Fleczok, Benjamin; Rathmann, Christian; Otibar, Dennis; Weirich, Antonia; Kuhlenkötter, Bernd

    2017-06-01

    The use of NiTi shape-memory alloys (SMA) in actuators bears significant advantages for designing robust, simple and lightweight applications. The SMA effect is based on a phase transformation of the atomic lattice in response to stress, strain and temperature. The resulting crystallographic configurations lead to a complex behavior revealing different electrical and mechanical characteristics. In view of the impact of thermo-mechanical cyclization on the operational lifetime, this paper investigates the influences of different types of electrical activation. For this purpose, six current curves with six samples each are compared to a reference activation with regard to the operational lifetime. The chosen time of activation is 1 second in accordance with an industrially relevant cycle of technical actuators. Based on the results of these investigations, recommendations of the activation type shall be developed for the operational lifetime of NiTi-SMA.

  3. Calibration and Finite Element Implementation of an Energy-Based Material Model for Shape Memory Alloys

    Science.gov (United States)

    Junker, Philipp; Hackl, Klaus

    2016-06-01

    Numerical simulations are a powerful tool to analyze the complex thermo-mechanically coupled material behavior of shape memory alloys during product engineering. The benefit of the simulations strongly depends on the quality of the underlying material model. In this contribution, we discuss a variational approach which is based solely on energetic considerations and demonstrate that unique calibration of such a model is sufficient to predict the material behavior at varying ambient temperature. In the beginning, we recall the necessary equations of the material model and explain the fundamental idea. Afterwards, we focus on the numerical implementation and provide all information that is needed for programing. Then, we show two different ways to calibrate the model and discuss the results. Furthermore, we show how this model is used during real-life industrial product engineering.

  4. Calibration and Finite Element Implementation of an Energy-Based Material Model for Shape Memory Alloys

    Science.gov (United States)

    Junker, Philipp; Hackl, Klaus

    2016-09-01

    Numerical simulations are a powerful tool to analyze the complex thermo-mechanically coupled material behavior of shape memory alloys during product engineering. The benefit of the simulations strongly depends on the quality of the underlying material model. In this contribution, we discuss a variational approach which is based solely on energetic considerations and demonstrate that unique calibration of such a model is sufficient to predict the material behavior at varying ambient temperature. In the beginning, we recall the necessary equations of the material model and explain the fundamental idea. Afterwards, we focus on the numerical implementation and provide all information that is needed for programing. Then, we show two different ways to calibrate the model and discuss the results. Furthermore, we show how this model is used during real-life industrial product engineering.

  5. A new look at biomedical Ti-based shape memory alloys.

    Science.gov (United States)

    Biesiekierski, Arne; Wang, James; Gepreel, Mohamed Abdel-Hady; Wen, Cuie

    2012-05-01

    Shape memory alloys (SMAs) are materials that exhibit a distinct thermomechanical coupling, one that gives rise to a wide variety of applications across a broad range of fields. One of the most successful roles is in the construction of novel medical implants. Unfortunately, concerns have been raised about the biocompatibility of the most popular SMA, nitinol (NiTi), due to the known toxic, allergenic and carcinogenic properties of nickel. Given the unique capabilities of SMAs, it is apparent that there is a need for a new class of alloys - alloys that exhibit the full range of shape memory abilities yet are also free of any undesirable side effects. This article reviews the literature surrounding SMAs and identifies the metals Ti, Au, Sn, Ta, Nb, Ru and Zr as candidates for the production of thoroughly biocompatible SMAs. Hf and Re are also promising, though more research is necessary before a definitive statement can be made. Further, the Ti-(Ta,Nb)-(Zr,Hf) alloy system is particularly suited for orthopaedic implants due to a reduced Young's modulus. However, concerns over this system's shape memory properties exist, and should be taken into consideration. Alternate alloy systems that demonstrate higher bulk moduli may still be considered, however, if they are formed into a porous structure. Due to the nature of the alloying components, blended elemental powder metallurgy is recommended for the manufacture of these alloys, particularly due to the ease with which it may be adapted to the formation of porous alloys. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

  6. Shakedown based model for high-cycle fatigue of shape memory alloys

    Science.gov (United States)

    Gu, Xiaojun; Moumni, Ziad; Zaki, Wael; Zhang, Weihong

    2016-11-01

    The paper presents a high-cycle fatigue criterion for shape memory alloys (SMAs) based on shakedown analysis. The analysis accounts for phase transformation as well as reorientation of martensite variants as possible sources of fatigue damage. In the case of high-cycle fatigue, once the structure has reached an asymptotic state, damage is assumed to become confined at the mesoscopic scale, or the scale of the grain, with no discernable inelasticity at the macroscopic scale. Using a multiscale approach, a high-cycle fatigue criterion analogous to the Dang Van model (Dang Van 1973) for elastoplastic metals is derived for SMAs obeying the Zaki-Moumni model for SMAs (Zaki and Moumni 2007a). For these alloys, a safe domain is established in stress deviator space, consisting of a hypercylinder with axis parallel to the direction of martensite orientation at the mesoscopic scale. Safety with regard to high-cycle fatigue, upon elastic shakedown, is conditioned by the persistence of the macroscopic stress path at every material point within the hypercylinder, whose size depends on the volume fraction of martensite. The proposed criterion computes a fatigue factor at each material point, indicating its degree of safeness with respect to high cycle fatigue.

  7. The effect of addition of various elements on properties of NiTi-based shape memory alloys for biomedical application

    Science.gov (United States)

    Kök, Mediha; Ateş, Gonca

    2017-04-01

    In biomedical applications, NiTi and NiTi-based alloys that show their shape memory effects at body temperature are preferred. In this study, the purpose is to produce NiTi and NiTi-based alloys with various chemical rates and electron concentrations and to examine their various physical properties. N45Ti55, Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Sn, Co) alloys were produced in an arc melter furnace in this study. After the homogenization of these alloys, the martensitic phase transformation temperatures were determined with differential-scanner calorimeter. The transformation temperature was found to be below the 37 ° C (body temperature) in Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Co) alloys; and the transformation temperature of the N45Ti55, Ni48Ti51Sn alloys was found to be over 37 ° C . Then, the micro and crystal structure analyses of the alloys were made, and it was determined that Ni45Ti50Cr2.5Cu2.5, Ni48Ti51X (X=Mn, Co) alloys, which were in austenite phase at room temperature, included B2 (NiTi) phase and Ti2Ni precipitation phase, and the alloys that were in the martensite phase at room temperature included B19ı (NiTi) phase and Ti2Ni phase. The common phase in both alloy groups is the Ti2Ni phase, and this type of phase is generally seen in NiTi alloys that are rich in titanium (Ti-rich).

  8. Electro-bending characterization of adaptive 3D fiber reinforced plastics based on shape memory alloys

    Science.gov (United States)

    Ashir, Moniruddoza; Hahn, Lars; Kluge, Axel; Nocke, Andreas; Cherif, Chokri

    2016-03-01

    The industrial importance of fiber reinforced plastics (FRPs) is growing steadily in recent years, which are mostly used in different niche products, has been growing steadily in recent years. The integration of sensors and actuators in FRP is potentially valuable for creating innovative applications and therefore the market acceptance of adaptive FRP is increasing. In particular, in the field of highly stressed FRP, structural integrated systems for continuous component parts monitoring play an important role. This presented work focuses on the electro-mechanical characterization of adaptive three-dimensional (3D)FRP with integrated textile-based actuators. Here, the friction spun hybrid yarn, consisting of shape memory alloy (SMA) in wire form as core, serves as an actuator. Because of the shape memory effect, the SMA-hybrid yarn returns to its original shape upon heating that also causes the deformation of adaptive 3D FRP. In order to investigate the influences of the deformation behavior of the adaptive 3D FRP, investigations in this research are varied according to the structural parameters such as radius of curvature of the adaptive 3D FRP, fabric types and number of layers of the fabric in the composite. Results show that reproducible deformations can be realized with adaptive 3D FRP and that structural parameters have a significant impact on the deformation capability.

  9. Design of Shape Memory Alloy-Based and Tendon-Driven Actuated Fingers towards a Hybrid Anthropomorphic Prosthetic Hand

    Directory of Open Access Journals (Sweden)

    Erkan Kaplanoglu

    2012-09-01

    Full Text Available This paper presents the design of tendon-driven actuated fingers using a shape memory alloy for a hybrid anthropomorphic prosthetic hand. The ring and little (pinky fingers are selected for shape memory activation due to their lower degree of movement during multiple grasping configurations. The fingers' tendon system is based on shape memory alloy (SMA wires that form artificial muscle pairs for the required flexion/extension of the finger joints. The finger has four degrees of freedom such that three of them are active. An experimental setup was developed to evaluate the performance of the ring and little fingers. An electromyography (EMG controlled Pulse Width Modulated (PWM technique is preferred for the actuation of joint motions using a high speed microcontroller.

  10. Design of Shape Memory Alloy-Based and Tendon-Driven Actuated Fingers Towards a Hybrid Anthropomorphic Prosthetic Hand

    Directory of Open Access Journals (Sweden)

    Erkan Kaplanoglu

    2012-09-01

    Full Text Available This paper presents the design of tendon‐driven actuated fingers using a shape memory alloy for a hybrid anthropomorphic prosthetic hand. The ring and little (pinky fingers are selected for shape memory activation due to their lower degree of movement during multiple grasping configurations. The fingersʹ tendon system is based on shape memory alloy (SMA wires that form artificial muscle pairs for the required flexion/extension of the finger joints. The finger has four degrees of freedom such that three of them are active. An experimental setup was developed to evaluate the performance of the ring and little fingers. An electromyography (EMG controlled Pulse Width Modulated (PWM technique is preferred for the actuation of joint motions using a high speed microcontroller.

  11. Perspectives on the exploitation of CuZnAl alloys, FeMnSi-based alloys and ZrO{sub 2}-containing shape-memory ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, T.Y. [Shanghai Jiao Tong Univ. (St. Helena). School of Materials Science and Engineering

    2002-07-01

    Cu-Zn-Al alloys possess advantages for exploitation such as low cost, easy fabrication and excellent shape memory effect (SME). The deficiencies of Cu-Zn-Al shape memory alloys, i.e. the appearance of the stabilization of martensite, degradation of SME in prolonged application and the rather low fatigue life, can be overcome by various processing such as immediate up-quenching, alloying addition for retarding the incubation of bainite formation and grain refinement. Fe-Mn-Si based alloys are one-way shape memory material with high strength, high action temperatures, good workability and low cost. Addition of nitrogen or rare earth (RE) elements can considerably strengthen the austenite and lower the Neel temperature in Fe-Mn-Si alloys. Partial replacement of Mn with Cr and addition of RE elements to Fe-Mn-Si may reduce its stacking fault energy. Nitrogen and RE elements also lower the M{sub s} temperature of Fe-Mn-Si and Fe-Mn-Si-Cr, stabilizing the austenite after shape recovery. The newly developed Fe-25Mn-6Si-5Cr-0.14N alloy possesses not only a complete shape memory recovery with a recoverable strain of 3% through only one cycle of training, but also the nice corrosion resistance in aqueous solution of NaOH and NaCl. The SME of Fe-Mn-Si-RE is superior to that of Fe-Mn-Si, e.g. its recoverable strain is about two-fold larger than that of Fe-Mn-Si when the pre-strain {epsilon}>3%. The exploitation of the Fe-Mn-Si-Cr-N and Fe-Mn-Si-RE alloys as coupling materials seems to be foresighted. Studies on (8{proportional_to}12)mol%CeO{sub 2}-(0.25{proportional_to}0.75)mol%Y{sub 2}O{sub 3}-ZrO{sub 2} with various grain size and density after different sintering processes show that 8mol%CeO{sub 2}-0.5mol%Y{sub 2}O{sub 3}-ZrO{sub 2} fabricated by sintering at 1773 K for 6 hours exhibits best SME, i.e. a complete shape memory recovery and a recoverable strain of 1.2% at high temperatures (above 773 K). The shape memory ceramics 8Ce-0.5Y-TZP is worthy to be developed. (orig.)

  12. Phase change memory based on SnSe{sub 4} alloy

    Energy Technology Data Exchange (ETDEWEB)

    Karanja, J.M.; Karimi, P.M.; Njoroge, W.K. [Physics Department, Kenyatta University, P.O. Box 43844, Nairobi (Kenya); Wamwangi, D.M., E-mail: Daniel.Wamwangi@wits.ac.za [School of Physics, University of the Witwatersrand, Private Bag 3, 2050 (South Africa)

    2013-01-01

    A phase change alloy has been synthesized and characterized. The reversible phase transitions between amorphous and crystalline states of SnSe{sub 4} films have been studied using variable electrical pulses and X-ray diffraction. Temperature dependent sheet resistance measurements have shown two distinct resistivity states of more than two orders of magnitude. This high electrical contrast makes the alloy suitable for nonvolatile phase change memory applications. X-ray diffraction has attributed the large electrical contrast to an amorphous–crystalline phase transition. The nonvolatile memory cells have been fabricated using a simple sandwich structure (metal/chalcogenide thin film/metal). A threshold voltage of 3.71 V has been determined for this phase change random access memory cell. Memory switching was initiated using the voltage pulses of 3.71 V, 90 ns, 1.3 V and 26 μs, for the crystallization and amorphization process, respectively. - Highlights: ► Phase transition of SnSe{sub 4} alloys with high set resistivity of 1.43 Ωm ► High transition temperatures of 174 °C ► Transition due to amorphous–crystalline changes ► Threshold switching at a high threshold voltage of 3.71 V.

  13. A New Shape Memory Alloy Based Smart Encoder for Sensing of Direction and Angular Motion

    Directory of Open Access Journals (Sweden)

    Bishakh BHATTACHARYA

    2011-07-01

    Full Text Available This paper presents a novel technique for sensing direction, angle and velocity from rotation of shafts using simple Shape Memory Alloy (SMA based micro-switches. Due to electro-mechanical coupling of SMA wires reflected in controlled force generation capacity, the SMA based devices can provide better alternatives for traditional relays, solenoid valves and opto-coupler isolators. The control algorithm involved in this sensing technique, reads the switch status for shaft rotation and sense the angular displacement thereafter. One of the advantages, this new sensor offers is its inherent robustness to vibration in the host platform. Experiments are carried out under vibrating conditions and obtained results are compared with conventional optical incremental encoder. The result shows that SMA based angle encoder works efficiently and gives more accurate results under disturbance while optical encoders are quite sensitive to similar platform vibration. Due to its compactness and lightweight, this concept of SMA wire based angle sensor is envisaged to be suitable for structural health monitoring applications where discrete angle information is needed at low RPM.

  14. An innovative seismic bracing system based on a superelastic shape memory alloy ring

    Science.gov (United States)

    Gao, Nan; Jeon, Jong-Su; Hodgson, Darel E.; DesRoches, Reginald

    2016-05-01

    Shape memory alloys (SMAs) have great potential in seismic applications because of their remarkable superelasticity. Seismic bracing systems based on SMAs can mitigate the damage caused by earthquakes. The current study investigates a bracing system based on an SMA ring which is capable of both re-centering and energy dissipation. This lateral force resisting system is a cross-braced system consisting of an SMA ring and four tension-only cable assemblies, which can be applied to both new construction and seismic retrofit. The performance of this bracing system is examined through a quasi-static cyclic loading test and finite element (FE) analysis. This paper describes the experimental design in detail, discusses the experimental results, compares the performance with other bracing systems based on SMAs, and presents an Abaqus FE model calibrated on the basis of experimental results to simulate the superelastic behavior of the SMA ring. The experimental results indicate that the seismic performance of this system is promising in terms of damping and re-centering. The FE model can be used in the simulation of building structures using the proposed bracing system.

  15. Design, modelling and control of a micro-positioning actuator based on magnetic shape memory alloys

    Science.gov (United States)

    Minorowicz, Bartosz; Leonetti, Giuseppe; Stefanski, Frederik; Binetti, Giulio; Naso, David

    2016-07-01

    This paper presents an actuator based on magnetic shape memory alloys (MSMAs) suitable for precise positioning in a wide range (up to 1 mm). The actuator is based on the spring returned operating mode and uses a Smalley wave spring to maintain the same operating parameters of a classical coil spring, while being characterized by a smaller dimension. The MSMA element inside the actuator provides a deformation when excited by an external magnetic field, but its behavior is characterized by an asymmetric and saturated hysteresis. Thus, two models are exploited in this work to represent such a non-linear behavior, i.e., the modified and generalized Prandtl-Ishlinskii models. These models are particularly suitable for control purposes due to the existence of their analytical inversion that can be easily exploited in real time control systems. To this aim, this paper investigates three closed-loop control strategies, namely a classical PID regulator, a PID regulator with direct hysteresis compensation, and a combined PID and feedforward compensation strategy. The effectiveness of both modelling and control strategies applied to the designed MSMA-based actuator is illustrated by means of experimental results.

  16. A chemical-structural model for coherent martensite/parent interface in Mn-based antiferromagnetic shape memory alloys.

    Science.gov (United States)

    Shi, S; Wan, J F; Zuo, X W; Chen, N L; Zhang, J H; Rong, Y H

    2016-11-21

    The martensite/parent coherent interface of Mn-based shape memory alloys (SMAs) is a significant part in the research of their martensitic transformation, reversible shape memory effect and magnetic shape memory effect. In the present work, a chemical-structural model was proposed to calculate the martensite/parent coherent interfacial energy of Mn-X (X = Cu, Fe) alloys. In this model, the coherent heterophase interfacial energy consists of chemical and structural parts. Resulting from the formation process of the heterophase interface, the chemical interfacial energy is expressed as the incremental value of bond energy, while the structural part is obtained by calculating the interfacial strain energy. The results show that the structural interfacial energy plays the chief role in the total interfacial energy, and the total interfacial energy decreases as the temperature rises when the alloy composition is fixed. In addition, the preferred orientation has noteworthy influence on the total interfacial energy. Using the proposed model, interfacial energy, interfacial entropy, interfacial enthalpy and interfacial heat capacity are found to be correlated with temperature and interface preferred orientation. Furthermore, the influences of alloy composition, modulus softening, and the index of the habit plane on the results were discussed.

  17. A NEW MODEL OF SHAPE MEMORY ALLOYS

    Institute of Scientific and Technical Information of China (English)

    朱祎国; 吕和祥; 杨大智

    2002-01-01

    A new constitutive model of shape memory alloys ( SMAs ) based on Tanaka' s martensite fraction exponential expression is produced. This new model can present recoverable shape memory strain during different phase transformation, and reflect the action of martensite reorientation. Also it can overcome the defect of Tanaka's Model when the SMAs' microstructure is fully martensite . The model is very simple and suitable for using,and the correct behavior of the model is proved by test.

  18. Structure evolution of Cu-based shape memory powder during mechanical alloying

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The microstructures of shape memory powders of Cu-Al-Ni prepared from pure powders of Cu, Al and Ni using the mechanical alloying(MA) technique were studied by means of hardness measurement, metallograph observation, XRD and SEM.The hardness reaches the peak as the increase in hardness due to plastic deformation and the decrease in hardness due to kinetic annealing reach a balance. The process of MA leads to the formation of a laminated structure, and the layer becomes thinner with an increase in milling time. The pre-alloyed shape memory powder can be formed by milling at 300 r/min for 50 h using a planetary ball mill.

  19. Transformation Temperatures, Shape Memory and Magnetic Properties of Hafnium Modified Ti-Ta Based High Temperature Shape Memory Alloys

    Science.gov (United States)

    Khan, W. Q.; Wang, Q.; Jin, X.

    2017-02-01

    In this study the modification effect of Hf content on the shape memory properties and magnetic permeability of a 75.5-77Ti-20Ta-3-4.5Hf alloy system has been systematically studied by DSC, three-point bend test, vector network analyzer and XRD. The martensitic transformation temperature, heat of reaction and recovery strain increases with the increase of hafnium and tantalum content. A stable high temperature shape memory effect was observed (Ms = 385-390 °C) during the two thermal cycles between 20 °C and 725 °C. Transformation temperatures and heats of reaction were determined by DSC measurements. Recovery strain was determined by three-point bend testing. Also an alloy, 70Ti-26Ta-4Hf, with higher tantalum content was produced to observe the effect of Ta on the shape memory properties. Permeability increases gradually from 1.671 to 1.919 with increasing content of hafnium modification and remains stable in the frequency range of 450 MHz to 1 GHz.

  20. Four logic states of tunneling magnetoelectroresistance in ferromagnetic shape memory alloy based multiferroic tunnel junctions

    Science.gov (United States)

    Singh, Kirandeep; Kaur, Davinder

    2017-07-01

    This study illustrates the approach to obtain four logic states of ferromagnetic shape memory alloy based multiferroic tunnel junction (MFTJ). In order to achieve giant tunneling electroresistance (TER) and tunneling magnetoresistance (TMR), Ni-Mn-In and Ni-Mn-Sb layers were chosen as electrodes, as well as the concept of the composite barrier was adopted using the STO/PZT [SrTiO3, Strontium Titanate/PbZr0.52Ti0.48O3 (Lead Zirconate Titanate)] (dielectric/ferroelectric) barrier layer. Equated to MFTJ with a single PZT barrier, the introduction of a STO paraelectric (dielectric) barrier is shown to be effective in improving both the TER and TMR of the MFTJs. Particularly, the TER ratio is greatly enhanced by 168% {" separators="|relative TER change: (ΔT/E R T E R =T/ER 2-TE R 1 TE R 1 ×100 }). This is described in terms of the increased asymmetry in the electrostatic modulation on the barrier potential profile with respect to the Ferroelectric (FE) polarization direction. We show that due to the coupling between FE polarization and magnetization at the junction between the barrier and the electrode of a MFTJ, the spin polarization of the tunneling electrons can be reversibly and remanently flipped by switching the FE polarization of the barrier. In addition to the analysis of memory function, the exchange bias phenomena are also studied. A negative exchange bias field of "HEB" ˜-98 Oe occurred at 300 K in these bilayers.

  1. Shape memory alloy-based moment connections with superior self-centering properties

    Science.gov (United States)

    Farmani, Mohammad Amin; Ghassemieh, Mehdi

    2016-07-01

    Superelastic shape memory alloys (SMAs) have the potential to create a spontaneous recentering mechanism on the connections of a structural system under seismic actions, which results in mitigation of the damage in the main structural members. In this article, innovative types of steel beam-to-column moment connections incorporating SMA bolts and plates are introduced and studied through a numerical approach. First, SMA bolted end-plate connection model is produced and analyzed by means of the finite element method to validate the numerical analysis against the prior experimental results. Then, the performance of eleven different end-plate moment connection models subjected to cyclic loading is investigated. By selecting the lower values for the moment capacity based on bolts strength in comparison to the flexural resistance of the beam, the plastic hinge is transferred from the beam section to the beam-column interface. Hence, employing superelastic materials at the connection interface could be potentially effective in providing the desired self-centering effect in the connection. To this end, the impact of utilizing superelastic SMA bolts and end-plates instead of using the conventional structural steel on the overall cyclic response of the connections is evaluated in this study. Results show that extended end-plate connections equipped with SMA bolts and end-plates, if properly proportioned and detailed, not only exhibit a clear reduction in the residual drifts after a seismic event, but also can meet the ductility requirements with good energy dissipation and sufficient stiffness.

  2. Energy-efficient miniature-scale heat pumping based on shape memory alloys

    Science.gov (United States)

    Ossmer, Hinnerk; Wendler, Frank; Gueltig, Marcel; Lambrecht, Franziska; Miyazaki, Shuichi; Kohl, Manfred

    2016-08-01

    Cooling and thermal management comprise a major part of global energy consumption. The by far most widespread cooling technology today is vapor compression, reaching rather high efficiencies, but promoting global warming due to the use of environmentally harmful refrigerants. For widespread emerging applications using microelectronics and micro-electro-mechanical systems, thermoelectrics is the most advanced technology, which however hardly reaches coefficients of performance (COP) above 2.0. Here, we introduce a new approach for energy-efficient heat pumping using the elastocaloric effect in shape memory alloys. This development is mainly targeted at applications on miniature scales, while larger scales are envisioned by massive parallelization. Base materials are cold-rolled textured Ti49.1Ni50.5Fe0.4 foils of 30 μm thickness showing an adiabatic temperature change of +20/-16 K upon superelastic loading/unloading. Different demonstrator layouts consisting of mechanically coupled bridge structures with large surface-to-volume ratios are developed allowing for control by a single actuator as well as work recovery. Heat transfer times are in the order of 1 s, being orders of magnitude faster than for bulk geometries. Thus, first demonstrators achieve values of specific heating and cooling power of 4.5 and 2.9 W g-1, respectively. A maximum temperature difference of 9.4 K between heat source and sink is reached within 2 min. Corresponding COP on the device level are 4.9 (heating) and 3.1 (cooling).

  3. Pulse width modulation-based temperature tracking for feedback control of a shape memory alloy actuator.

    Science.gov (United States)

    Ayvali, Elif; Desai, Jaydev P

    2014-04-01

    This work presents a temperature-feedback approach to control the radius of curvature of an arc-shaped shape memory alloy (SMA) wire. The nonlinear properties of the SMA such as phase transformation and its dependence on temperature and stress make SMA actuators difficult to control. Tracking a desired trajectory is more challenging than controlling just the position of the SMA actuator since the desired path is continuously changing. Consequently, tracking the desired strain directly or tracking the parameters such as temperature and electrical resistance that are related to strain with a model is a challenging task. Temperature-feedback is an attractive approach when direct measurement of strain is not practical. Pulse width modulation (PWM) is an effective method for SMA actuation and it can be used along with a compensator to control the temperature of the SMA. Using the constitutive model of the SMA, the desired temperature profile can be obtained for a given strain trajectory. A PWM-based nonlinear PID controller with a feed-forward heat transfer model is proposed to use temperature-feedback for tracking a desired temperature trajectory. The proposed controller is used during the heating phase of the SMA actuator. The controller proves to be effective in tracking step-wise and continuous trajectories.

  4. Design and property analysis of a hybrid linear actuator based on shape memory alloy

    Science.gov (United States)

    Zhang, Xiaoguang; Hu, Jinhong; Mao, Shixin; Dong, Erbao; Yang, Jie

    2014-12-01

    This paper introduces two methods for solving two bottlelike problems regarding the shape memory alloy (SMA) application as actuators. These methods are ‘rotating output,’ which aims to solve the problem of the low working frequency caused by the demand for cool time, and ‘accumulated shifting,’ which solves the problem of difficult-to-obtain output displacements in a large scale. We also introduce a hybrid linear actuator that applies the two methods and achieves both a strong force and an accurate large output displacement while working at a high frequency based on the SMA wires and DC motors. A prototype of this actuator was fabricated and tested to verify the two methods. This hybrid actuator system dynamic model, which was composed of the constitutive model of the SMA, the electrical and heat transfer behavior of the SMA wires and the dynamics of the linear actuation system, was established and discussed. Our study aims to illuminate the application of an SMA in actuators with the proposed methods with regard to its two main problems. An actuator with a high power-weight ratio and the capability to work at a high frequency, as well as accurate linear step displacements in a large scale, is also presented.

  5. New Design of a Soft Robotics Wearable Elbow Exoskeleton Based on Shape Memory Alloy Wire Actuators

    Directory of Open Access Journals (Sweden)

    Dorin Copaci

    2017-01-01

    Full Text Available The elbow joint is a complex articulation composed of the humeroulnar and humeroradial joints (for flexion-extension movement and the proximal radioulnar articulation (for pronation-supination movement. During the flexion-extension movement of the elbow joint, the rotation center changes and this articulation cannot be truly represented as a simple hinge joint. The main goal of this project is to design and assemble a medical rehabilitation exoskeleton for the elbow with one degree of freedom for flexion-extension, using the rotation center for proper patient elbow joint articulation. Compared with the current solutions, which align the exoskeleton axis with the elbow axis, this offers an ergonomic physical human-robot interface with a comfortable interaction. The exoskeleton is actuated with shape memory alloy wire-based actuators having minimum rigid parts, for guiding the actuators. Thanks to this unusual actuation system, the proposed exoskeleton is lightweight and has low noise in operation with a simple design 3D-printed structure. Using this exoskeleton, these advantages will improve the medical rehabilitation process of patients that suffered stroke and will influence how their lifestyle will change to recover from these diseases and improve their ability with activities of daily living, thanks to brain plasticity. The exoskeleton can also be used to evaluate the real status of a patient, with stroke and even spinal cord injury, thanks to an elbow movement analysis.

  6. Shape Memory Alloys (Part II: Classification, Production and Application

    Directory of Open Access Journals (Sweden)

    I. Ivanic

    2014-09-01

    Full Text Available Shape memory alloys (SMAs have been extensively investigated because of their unique shape memory behaviour, i.e. their ability to recover their original shape they had before deformation. Shape memory effect is related to the thermoelastic martensitic transformation. Austenite to martensite phase transformation can be obtained by mechanical (loading and thermal methods (heating and cooling. Depending on thermomechanical conditions, SMAs demonstrate several thermomechanical phenomena, such as pseudoelasticity, superelasticity, shape memory effect (one-way and two-way and rubber-like behaviour. Numerous alloys show shape memory effect (NiTi-based alloys, Cu-based alloys, Fe-based alloys etc.. Nitinol (NiTi is the most popular and the most commonly used SMA due to its superior thermomechanical and thermoelectrical properties. NiTi alloys have greater shape memory strain and excellent corrosion resistance compared to Cu – based alloys. However, they are very costly. On the other hand, copper-based alloys (CuZn and CuAl based alloys are much less expensive, easier to manufacture and have a wider range of potential transformation temperatures. The characteristic transformation temperatures of martensitic transformation of CuAlNi alloys can lie between −200 and 200 °C, and these temperatures depend on Al and Ni content. Among the Cu – based SMAs, the most frequently applied are CuZnAl and CuAlNi alloys. Although CuZnAl alloys with better mechanical properties are the most popular among the Cu-based SMAs, they lack sufficient thermal stability, while CuAlNi shape memory alloys, in spite of their better thermal stability, have found only limited applications due to insufficient formability owing to the brittle γ2 precipitates. The most important disadvantage of polycrystalline CuAlNi alloys is a small reversible deformation (one-way shape memory effect: up to 4 %; two-way shape memory effect: only approximately 1.5 % due to intergranular

  7. Application of Laguerre based adaptive predictive control to Shape Memory Alloy (SMA) Actuator.

    Science.gov (United States)

    Kannan, S; Giraud-Audine, C; Patoor, E

    2013-07-01

    This paper discusses the use of an existing adaptive predictive controller to control some Shape Memory Alloy (SMA) linear actuators. The model consists in a truncated linear combination of Laguerre filters identified online. The controller stability is studied in details. It is proven that the tracking error is asymptotically stable under some conditions on the modelling error. Moreover, the tracking error converge toward zero for step references, even if the identified model is inaccurate. Experimental results obtained on two different kind of actuator validate the proposed control. They also show that it is robust with regard to input constraints.

  8. Design optimization of shape memory alloy structures

    NARCIS (Netherlands)

    Langelaar, M.

    2006-01-01

    This thesis explores the possibilities of design optimization techniques for designing shape memory alloy structures. Shape memory alloys are materials which, after deformation, can recover their initial shape when heated. This effect can be used for actuation. Emerging applications for shape memory

  9. Design optimization of shape memory alloy structures

    NARCIS (Netherlands)

    Langelaar, M.

    2006-01-01

    This thesis explores the possibilities of design optimization techniques for designing shape memory alloy structures. Shape memory alloys are materials which, after deformation, can recover their initial shape when heated. This effect can be used for actuation. Emerging applications for shape memory

  10. Performance evaluation of shape memory alloy/rubber-based isolation systems for seismic response mitigation of bridges

    Science.gov (United States)

    Ozbulut, Osman E.; Hurlebaus, Stefan

    2010-04-01

    Base isolation is an effective method of reducing seismic response of bridges during an earthquake. Rubber isolators are one of the most common types of base isolation systems. As an alternative to conventional rubber isolators such as high damping rubber bearing and lead rubber bearing, smart rubber bearing systems with shape memory alloys (SMAs) have been proposed in recent years. As a class of smart materials, shape memory alloys shows excellent re-centering and considerable damping capabilities which can be exploited to obtain an efficient seismic isolation system. This paper explores effectiveness of shape memory alloy/rubber-based isolation systems for protecting bridges against seismic loads by performing a sensitivity analysis. The isolation system considered in this study consists of a laminated rubber bearing which provides lateral flexibility while supplying high vertical load-carrying capacity and an auxiliary device made of multiple loops SMA wires. The SMA device offers additional energy dissipating and re-centering capability. A threespan continuous bridge is modeled with SMA/rubber-based isolation system. Numerical simulations of the bridge are conducted for various historical ground motions that are spectrally matched to a target design spectrum. The normalized yield strength, yield displacement and pre-stress level of the SMA device and ambient temperature are selected as parameters of the sensitivity study. The variation of seismic response of the bridge with considered parameters is assessed. The optimum values of the normalized yield strength and the yield displacement of the SMA device is found to be in the range of 0.20-0.25 and 40-50 mm, respectively. Also, the SMA/rubber-based isolation system is observed to be more effective when the SMA device is pre-stressed. In addition, it is found that ambient temperature considerably affects the performance of the bridge isolated by SMA/rubber-based isolators.

  11. Ultralow-fatigue shape memory alloy films

    National Research Council Canada - National Science Library

    Chluba, C; Ge, W; Lima de Miranda, R; Strobel, J; Kienle, L; Quandt, E; Wuttig, M

    2015-01-01

    Functional shape memory alloys need to operate reversibly and repeatedly. Quantitative measures of reversibility include the relative volume change of the participating phases and compatibility matrices for twinning...

  12. Applications of shape memory alloys in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Asai, M.; Suzuki, Y. [Furukawa Electric Co., Ltd., Yokohama, Kanagawa (Japan). R and D Labs.

    2000-07-01

    In Japan, a first application of shape memory TiNi alloy was a moving flap in an air-conditioner which was developed as sensing function of shape memory alloy at Matsushista Electric Industrial Co. Then, shape memory utilized in a coffee maker, an electric rice-cooker, a thermal mixing valve and etc. were commercialized in Japan. And brassiere wires, a guide wire for medical treatment, an antenna for portable telephone and others were commercialized utilizing superelasticity. At the same time with these commercial products, there was not only progress in fabrication technology to effect accurate transformation temperature, but also the discovery of small hysteresis alloy such as R-phase or TiNiCu alloy and low transformation temperature alloy such as TiNiFe, TiNiV and TiNiCo alloys. Therefore the shape memory alloy market has expanded widely to electric appliances, automobile, residence, medical care and otherfield today. (orig.)

  13. An active compression bandage based on shape memory alloys: a preliminary investigation.

    Science.gov (United States)

    Moein, Hadi; Menon, Carlo

    2014-09-11

    Disorders associated with excessive swelling of the lower extremities are common. They can be associated with pain, varicose veins, reduced blood pressure when standing and may cause syncope or fainting. The common physical remedy to these disorders is the use of compression stockings and pneumatic compression leg massagers, which both attempt to limit blood pooling and capillary filtration in the lower limbs. However, compression stockings provide a constant pressure, and their efficiency has been challenged according to some recent studies. Air compression leg massagers on the other hand, restricts patient mobility. In this work we therefore present an innovative active compression bandage based on the use of a smart materials technology that could produce intermittent active pressure to mitigate the symptoms of lower extremity disorders. An active compression bandage (ACB), actuated by shape memory alloy (SMA) wires, was designed and prototyped. The ACB was wrapped around a calf model to apply an initial pressure comparable to the one exerted by commercial compression stockings. The ACB was controlled to apply different values of compression. A data acquisition board and a LabVIEW program were used to acquire both the pressure data exerted by the ACB and the electrical current required to actuate the SMA wires. An analytical model of the ACB based on a SMA constitutive model was developed. An optimizer was implemented to identify optimal parameters of the model to best estimate the performance of the ACB. The maximum increase in pressure due to the SMA wires activation was 40.8% higher than the initially applied pressure to the calf model. The analytical model of the ACB estimated the behaviour of the ACB with less than 0.32 mmHg difference with the experimental results. The prototyped ACB was able to apply an initial compression comparable to the one applied by commercial compression stockings. Activation of the ACB resulted in an increase of compression up to

  14. A macroscopic multi-mechanism based constitutive model for the thermo-mechanical cyclic degeneration of shape memory effect of NiTi shape memory alloy

    Science.gov (United States)

    Yu, Chao; Kang, Guozheng; Kan, Qianhua

    2017-06-01

    A macroscopic based multi-mechanism constitutive model is constructed in the framework of irreversible thermodynamics to describe the degeneration of shape memory effect occurring in the thermo-mechanical cyclic deformation of NiTi shape memory alloys (SMAs). Three phases, austenite A, twinned martensite Mt and detwinned martensite Md, as well as the phase transitions occurring between each pair of phases (A→ M t, Mt→ A, A→ M d, Md→ A, and Mt→ M d) are considered in the proposed model. Meanwhile, two kinds of inelastic deformation mechanisms, martensite transformation-induced plasticity and reorientation-induced plasticity, are used to explain the degeneration of shape memory effects of NiTi SMAs. The evolution equations of internal variables are proposed by attributing the degeneration of shape memory effect to the interaction between the three phases ( A, Mt, and Md) and plastic deformation. Finally, the capability of the proposed model is verified by comparing the predictions with the experimental results of NiTi SMAs. It is shown that the degeneration of shape memory effect and its dependence on the loading level can be reasonably described by the proposed model.

  15. Tracking control of shape-memory-alloy actuators based on self-sensing feedback and inverse hysteresis compensation.

    Science.gov (United States)

    Liu, Shu-Hung; Huang, Tse-Shih; Yen, Jia-Yush

    2010-01-01

    Shape memory alloys (SMAs) offer a high power-to-weight ratio, large recovery strain, and low driving voltages, and have thus attracted considerable research attention. The difficulty of controlling SMA actuators arises from their highly nonlinear hysteresis and temperature dependence. This paper describes a combination of self-sensing and model-based control, where the model includes both the major and minor hysteresis loops as well as the thermodynamics effects. The self-sensing algorithm uses only the power width modulation (PWM) signal and requires no heavy equipment. The method can achieve high-accuracy servo control and is especially suitable for miniaturized applications.

  16. Tracking Control of Shape-Memory-Alloy Actuators Based on Self-Sensing Feedback and Inverse Hysteresis Compensation

    Directory of Open Access Journals (Sweden)

    Shu-Hung Liu

    2009-12-01

    Full Text Available Shape memory alloys (SMAs offer a high power-to-weight ratio, large recovery strain, and low driving voltages, and have thus attracted considerable research attention. The difficulty of controlling SMA actuators arises from their highly nonlinear hysteresis and temperature dependence. This paper describes a combination of self-sensing and model-based control, where the model includes both the major and minor hysteresis loops as well as the thermodynamics effects. The self-sensing algorithm uses only the power width modulation (PWM signal and requires no heavy equipment. The method can achieve high-accuracy servo control and is especially suitable for miniaturized applications.

  17. Multiscale investigation of inhomogeneous plastic deformation of NiTi shape memory alloy based on local canning compression

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Shuyong, E-mail: jiangshy@sina.com [Industrial Training Centre, Harbin Engineering University, Harbin 150001 (China); Hu, Li [College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Zhao, Yanan; Zhang, Yanqiu [Industrial Training Centre, Harbin Engineering University, Harbin 150001 (China); Liang, Yulong [College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China)

    2013-05-01

    As a severe plastic deformation (SPD) technique, local canning compression provides a novel approach to produce bulk amorphous and nanocrystalline nickel–titanium shape memory alloy (NiTi SMA). From the macroscale, mesoscale and microscale viewpoint, physical mechanism of inhomogeneous plastic deformation of NiTi alloy under local canning compression is investigated by means of optical microscopy, transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). Inhomogeneous plastic deformation of NiTi alloy leads to coexistence of amorphous phase, nanocrystalline phase, B2 austenite and B19′ martensite. The interaction between the dislocations and the grain boundaries lays the profound foundation for guaranteeing the continuity and the compatibility between the grains in a polycrystalline NiTi sample subjected to inhomogeneous plastic deformation. Deformation twinning and dislocation slip are the two important deformation modes in plastic deformation of NiTi alloy under local canning compression. Based on the statistically stored dislocation and the geometrically necessary dislocation, the mechanism of the critical dislocation density plays a predominant role in the occurrence of the amorphous phase in the deformed NiTi sample. When the deformation temperature is higher than a critical temperature, the amorphous phase is not able to occur in the NiTi sample subjected to SPD.

  18. Nonlinear Analysis of Actuation Performance of Shape Memory Alloy Composite Film Based on Silicon Substrate

    Directory of Open Access Journals (Sweden)

    Shuangshuang Sun

    2014-01-01

    Full Text Available The mechanical model of the shape memory alloy (SMA composite film with silicon (Si substrate was established by the method of mechanics of composite materials. The coupled action between the SMA film and Si substrate under thermal loads was analyzed by combining static equilibrium equations, geometric equations, and physical equations. The material nonlinearity of SMA and the geometric nonlinearity of bending deformation were both considered. By simulating and analyzing the actuation performance of the SMA composite film during one cooling-heating thermal cycle, it is found that the final cooling temperature, boundary condition, and the thickness of SMA film have significant effects on the actuation performance of the SMA composite film. Besides, the maximum deflection of the SMA composite film is affected obviously by the geometric nonlinearity of bending deformation when the thickness of SMA film is very large.

  19. Shape memory alloy-based biopsy device for active locomotive intestinal capsule endoscope.

    Science.gov (United States)

    Le, Viet Ha; Hernando, Leon-Rodriguez; Lee, Cheong; Choi, Hyunchul; Jin, Zhen; Nguyen, Kim Tien; Go, Gwangjun; Ko, Seong-Young; Park, Jong-Oh; Park, Sukho

    2015-03-01

    Recently, capsule endoscopes have been used for diagnosis in digestive organs. However, because a capsule endoscope does not have a locomotive function, its use has been limited to small tubular digestive organs, such as small intestine and esophagus. To address this problem, researchers have begun studying an active locomotive intestine capsule endoscope as a medical instrument for the whole gastrointestinal tract. We have developed a capsule endoscope with a small permanent magnet that is actuated by an electromagnetic actuation system, allowing active and flexible movement in the patient's gut environment. In addition, researchers have noted the need for a biopsy function in capsule endoscope for the definitive diagnosis of digestive diseases. Therefore, this paper proposes a novel robotic biopsy device for active locomotive intestine capsule endoscope. The proposed biopsy device has a sharp blade connected with a shape memory alloy actuator. The biopsy device measuring 12 mm in diameter and 3 mm in length was integrated into our capsule endoscope prototype, where the device's sharp blade was activated and exposed by the shape memory alloy actuator. Then the electromagnetic actuation system generated a specific motion of the capsule endoscope to extract the tissue sample from the intestines. The final biopsy sample tissue had a volume of about 6 mm(3), which is a sufficient amount for a histological analysis. Consequently, we proposed the working principle of the biopsy device and conducted an in-vitro biopsy test to verify the feasibility of the biopsy device integrated into the capsule endoscope prototype using the electro-magnetic actuation system. © IMechE 2015.

  20. Shape memory alloys: New materials for future engineering

    Science.gov (United States)

    Hornbogen, E.

    1988-01-01

    Shape memory is a new material property. An alloy which experiences relative severe plastic deformation resumes its original shape again after heating by 10 to 100 C. Besides simple shape memory, in similar alloys there is the second effect where the change in shape is caused exclusively by little temperature change. In pseudo-elasticity, the alloy exhibits a rubber-like behavior, i.e., large, reversible deformation at little change in tension. Beta Cu and beta NiTi alloys have been used in practice. The probability is that soon alloys based on Fe will become available. Recently increasing applications for this alloy were found in various areas of technology, even medical technology. A review with 24 references is given, including properties, production, applications and fundamental principles of the shape memory effect.

  1. Ferrous polycrystalline shape-memory alloy showing huge superelasticity.

    Science.gov (United States)

    Tanaka, Y; Himuro, Y; Kainuma, R; Sutou, Y; Omori, T; Ishida, K

    2010-03-19

    Shape-memory alloys, such as Ni-Ti and Cu-Zn-Al, show a large reversible strain of more than several percent due to superelasticity. In particular, the Ni-Ti-based alloy, which exhibits some ductility and excellent superelastic strain, is the only superelastic material available for practical applications at present. We herein describe a ferrous polycrystalline, high-strength, shape-memory alloy exhibiting a superelastic strain of more than 13%, with a tensile strength above 1 gigapascal, which is almost twice the maximum superelastic strain obtained in the Ni-Ti alloys. Furthermore, this ferrous alloy has a very large damping capacity and exhibits a large reversible change in magnetization during loading and unloading. This ferrous shape-memory alloy has great potential as a high-damping and sensor material.

  2. A Phase Change Memory Chip Based on TiSbTe Alloy in 40-nm Standard CMOS Technology

    Institute of Scientific and Technical Information of China (English)

    Zhitang Song; YiPeng Zhan; Daolin Cai; Bo Liu; Yifeng Chen; Jiadong Ren

    2015-01-01

    In this letter, a phase change random access memory (PCRAM) chip based on Ti0.4Sb2Te3 alloy material was fabricated in a 40-nm 4-metal level complementary metal-oxide semiconductor (CMOS) technology. The phase change resistor was then integrated after CMOS logic fabrication. The PCRAM was successfully embedded without changing any logic device and process, in which 1.1 V negative-channel metal-oxide semiconductor device was used as the memory cell selector. The currents and the time of SET and RESET operations were found to be 0.2 and 0.5 mA, 100 and 10 ns, respectively. The high speed performance of this chip may highlight the design advantages in many embedded applications.

  3. Properties of Cu-Based Shape-Memory Alloys Prepared by Selective Laser Melting

    Science.gov (United States)

    Gustmann, T.; dos Santos, J. M.; Gargarella, P.; Kühn, U.; Van Humbeeck, J.; Pauly, S.

    2016-12-01

    Two shape-memory alloys with the nominal compositions (in wt.%) Cu-11.85Al-3.2Ni-3Mn and Cu-11.35Al-3.2Ni-3Mn-0.5Zr were prepared by selective laser melting (SLM). The parameters were optimised to identify the process window, in which almost fully dense samples can be obtained. Their microstructures were analysed and correlated with the shape-memory behaviour as well as the mechanical properties. Suction-cast specimens were also produced for comparison. Mainly, β 1' martensite forms in all samples, but 0.5 wt.% of Zr stabilises the Y phase (Cu2AlZr), and its morphology depends on the thermal history and cooling rate. After annealing, the Y phase is primarily found at the grain boundaries hampering grain coarsening. Due to the relative high cooling rates applied here, Zr is mostly dissolved in the martensite in the as-prepared samples and it has a grain-refining effect only up to a critical cooling rate. The Zr-containing samples have increased transformation temperatures, and the Y phase seems to be responsible for the jerky martensite-to-austenite transformation. All the samples are relatively ductile because they mostly fracture in a transgranular manner, exhibiting the typical double yielding. Selective laser melting allows the adjustment of the transformation temperatures and the mechanical properties already during processing without the need of a subsequent heat treatment.

  4. Properties of Cu-Based Shape-Memory Alloys Prepared by Selective Laser Melting

    Science.gov (United States)

    Gustmann, T.; dos Santos, J. M.; Gargarella, P.; Kühn, U.; Van Humbeeck, J.; Pauly, S.

    2017-03-01

    Two shape-memory alloys with the nominal compositions (in wt.%) Cu-11.85Al-3.2Ni-3Mn and Cu-11.35Al-3.2Ni-3Mn-0.5Zr were prepared by selective laser melting (SLM). The parameters were optimised to identify the process window, in which almost fully dense samples can be obtained. Their microstructures were analysed and correlated with the shape-memory behaviour as well as the mechanical properties. Suction-cast specimens were also produced for comparison. Mainly, β 1' martensite forms in all samples, but 0.5 wt.% of Zr stabilises the Y phase (Cu2AlZr), and its morphology depends on the thermal history and cooling rate. After annealing, the Y phase is primarily found at the grain boundaries hampering grain coarsening. Due to the relative high cooling rates applied here, Zr is mostly dissolved in the martensite in the as-prepared samples and it has a grain-refining effect only up to a critical cooling rate. The Zr-containing samples have increased transformation temperatures, and the Y phase seems to be responsible for the jerky martensite-to-austenite transformation. All the samples are relatively ductile because they mostly fracture in a transgranular manner, exhibiting the typical double yielding. Selective laser melting allows the adjustment of the transformation temperatures and the mechanical properties already during processing without the need of a subsequent heat treatment.

  5. Electrically Actuated Antiglare Rear-View Mirror Based on a Shape Memory Alloy Actuator

    Science.gov (United States)

    Luchetti, T.; Zanella, A.; Biasiotto, M.; Saccagno, A.

    2009-08-01

    This article focuses on the experience of Centro Ricerche FIAT (CRF) regarding the development of shape memory alloy (SMA) actuators, and addressed some new design approaches which have been defined. Specific characteristics of shape memory materials, such as the efficiency of the transformation, have oriented the design of actuators toward occasionally used devices. The antiglare manual mechanism, incorporated in the internal rear-view mirror of a car, fits this new approach well. An antiglare rear-view mirror is a system capable of detecting a glare situation during night-time driving in order to automatically switch the mirror plane so as not to distract the driver. The low forces required, together with the silent, bi-stable movement are suitable for the use of a SMA actuator in this application. In the first part of the paper, the conceptual design is illustrated and a preliminary overview of the working principle is provided together with a series of considerations regarding the kinematics and the layout of electronic sensors in order to realize a fully controlled mechatronic prototype. Before concluding, the description of the realization of a working prototype is presented. The prototype of the EAGLE (Electrically Actuated antiGLare rEar-view mirror) system has provided experimental confirmation that such a device can satisfy fatigue and functional test requirements, thus offering the opportunity to spread the use of SMA devices in the automotive field.

  6. Design and development of a shape memory alloy activated heat pipe-based thermal switch

    Science.gov (United States)

    Benafan, O.; Notardonato, W. U.; Meneghelli, B. J.; Vaidyanathan, R.

    2013-10-01

    This work reports on the design, fabrication and testing of a thermal switch wherein the open and closed states were actuated by shape memory alloy (SMA) elements while heat was transferred by a two-phase heat pipe. The motivation for such a switch comes from NASA’s need for thermal management in advanced spaceport applications associated with future lunar and Mars missions. As the temperature can approximately vary between -233 and 127 ° C during lunar day/night cycles, the switch was designed to reject heat from a cryogen tank into space during the night cycle while providing thermal isolation during the day cycle. A Ni47.1Ti49.6Fe3.3 (at.%) alloy that exhibited a reversible phase transformation between a trigonal R-phase and a cubic austenite phase was used as the sensing and actuating elements. Thermomechanical actuation, accomplished through an antagonistic spring system, resulted in strokes up to 7 mm against bias forces of up to 45 N. The actuation system was tested for more than thirty cycles, equivalent to one year of operation. The thermal performance, accomplished via a variable length, closed two-phase heat pipe, was evaluated, resulting in heat transfer rates of 13 W using pentane and 10 W using R-134a as working fluids. Experimental data were also compared to theoretical predictions where possible. Direct comparisons between different design approaches of SMA helical actuators, highlighting the effects of the helix angle, were carried out to give a layout of more accurate design methodologies.

  7. Enhanced photomechanical response of a Ni–Ti shape memory alloy coated with polymer-based photothermal composites

    Science.gov (United States)

    Perez-Zúñiga, M. G.; Sánchez-Arévalo, F. M.; Hernández-Cordero, J.

    2017-10-01

    A simple way to enhance the activation of shape memory effects with light in a Ni–Ti alloy is demonstrated. Using polydimethylsiloxane-carbon nanopowder (PDMS+CNP) composites as coatings, the one-way shape memory effect (OWSME) of the alloy can be triggered using low power IR light from a laser diode. The PDMS+CNP coatings serve as photothermal materials capable to absorb light, and subsequently generate and dissipate heat in a highly efficient manner, thereby reducing the optical powers required for triggering the OWSME in the Ni–Ti alloy. Experimental results with a cantilever flexural test using both, bare Ni–Ti and coated samples, show that the PDMS+CNP coatings perform as thermal boosters, and therefore the temperatures required for phase transformation in the alloy can be readily obtained with low laser powers. It is also shown that the two-way shape memory effect (TWSME) can be set in the Ni–Ti alloy through cycling the TWSME by simply modulating the laser diode signal. This provides a simple means for training the material, yielding a light driven actuator capable to provide forces in the mN range. Hence, the use of photothermal coatings on Ni–Ti shape memory alloys may offer new possibilities for developing light-controlled smart actuators.

  8. GA-based optimum design of a shape memory alloy device for seismic response mitigation

    Science.gov (United States)

    Ozbulut, O. E.; Roschke, P. N.; Y Lin, P.; Loh, C. H.

    2010-06-01

    Damping systems discussed in this work are optimized so that a three-story steel frame structure and its shape memory alloy (SMA) bracing system minimize response metrics due to a custom-tailored earthquake excitation. Multiple-objective numerical optimization that simultaneously minimizes displacements and accelerations of the structure is carried out with a genetic algorithm (GA) in order to optimize SMA bracing elements within the structure. After design of an optimal SMA damping system is complete, full-scale experimental shake table tests are conducted on a large-scale steel frame that is equipped with the optimal SMA devices. A fuzzy inference system is developed from data collected during the testing to simulate the dynamic material response of the SMA bracing subcomponents. Finally, nonlinear analyses of a three-story braced frame are carried out to evaluate the performance of comparable SMA and commonly used steel braces under dynamic loading conditions and to assess the effectiveness of GA-optimized SMA bracing design as compared to alternative designs of SMA braces. It is shown that peak displacement of a structure can be reduced without causing significant acceleration response amplification through a judicious selection of physical characteristics of the SMA devices. Also, SMA devices provide a recentering mechanism for the structure to return to its original position after a seismic event.

  9. Hysteresis Modeling of Magnetic Shape Memory Alloy Actuator Based on Krasnosel'skii-Pokrovskii Model

    Directory of Open Access Journals (Sweden)

    Miaolei Zhou

    2013-01-01

    Full Text Available As a new type of intelligent material, magnetically shape memory alloy (MSMA has a good performance in its applications in the actuator manufacturing. Compared with traditional actuators, MSMA actuator has the advantages as fast response and large deformation; however, the hysteresis nonlinearity of the MSMA actuator restricts its further improving of control precision. In this paper, an improved Krasnosel'skii-Pokrovskii (KP model is used to establish the hysteresis model of MSMA actuator. To identify the weighting parameters of the KP operators, an improved gradient correction algorithm and a variable step-size recursive least square estimation algorithm are proposed in this paper. In order to demonstrate the validity of the proposed modeling approach, simulation experiments are performed, simulations with improved gradient correction algorithm and variable step-size recursive least square estimation algorithm are studied, respectively. Simulation results of both identification algorithms demonstrate that the proposed modeling approach in this paper can establish an effective and accurate hysteresis model for MSMA actuator, and it provides a foundation for improving the control precision of MSMA actuator.

  10. Hysteresis modeling of magnetic shape memory alloy actuator based on Krasnosel'skii-Pokrovskii model.

    Science.gov (United States)

    Zhou, Miaolei; Wang, Shoubin; Gao, Wei

    2013-01-01

    As a new type of intelligent material, magnetically shape memory alloy (MSMA) has a good performance in its applications in the actuator manufacturing. Compared with traditional actuators, MSMA actuator has the advantages as fast response and large deformation; however, the hysteresis nonlinearity of the MSMA actuator restricts its further improving of control precision. In this paper, an improved Krasnosel'skii-Pokrovskii (KP) model is used to establish the hysteresis model of MSMA actuator. To identify the weighting parameters of the KP operators, an improved gradient correction algorithm and a variable step-size recursive least square estimation algorithm are proposed in this paper. In order to demonstrate the validity of the proposed modeling approach, simulation experiments are performed, simulations with improved gradient correction algorithm and variable step-size recursive least square estimation algorithm are studied, respectively. Simulation results of both identification algorithms demonstrate that the proposed modeling approach in this paper can establish an effective and accurate hysteresis model for MSMA actuator, and it provides a foundation for improving the control precision of MSMA actuator.

  11. Factors influencing martensite transitions in Fe-based shape memory alloys

    Directory of Open Access Journals (Sweden)

    Mihalache Elena

    2015-01-01

    Full Text Available Fe-14Mn-6Si-9Cr-5Ni (mass % shape memory alloy (SMA specimens were obtained by powder metallurgy in as-blended state (0_MA and with particle volume fractions of 10 and 20 % MA’d powders, respectively. After hot rolling and solution treatment, between 973 and 1373 K, the specimens were pre-strained up to 4 %, on a tensile testing machine. The influences of: (i MA’d fractions, (ii solution treatment temperature and (iii pre-straining degree were analysed by X-ray diffraction (XRD, optical (OM and scanning electron (SEM microscopy. In this purpose, the gauges of pre-strained specimens were cut and metallographically prepared. Dynamic mechanical analysis (DMA was employed to emphasize the reverse transformation, during heating, of thermally induced martensite, obtained after solution treatment. The results proved that, as an effect of PM-MA processing, mechanical properties were improved, the amount of stress induced martensite increased and the reverse martensitic transformation was enhanced.

  12. Deformation Mechanism of Hot Spinning of NiTi Shape Memory Alloy Tube Based on FEM

    Institute of Scientific and Technical Information of China (English)

    JIANG Shuyong; ZHANG Yanqiu; ZHENG Yufeng; LI Chunfeng

    2012-01-01

    As a successively and locally plastic deformation process,ball spinning is applied to manufacturing thin-walled Nickel-Titanium shape memory alloy (NiTi SMA) tube at high temperature.NiTi SMA tube blank belongs to the as-cast state which consists of a lot of dendritic grains and a few equiaxed grains.The compression tests of NiTi SMA were carried out at various strain rates at high temperature in order to obtain the constitutive model of NiTi SMA.Because NiTi SMA is sensitive to the strain rates at high temperature,rigid-viscoplastic finite element method (FEM) is used to simulate ball spinning of thin-walled NiTi SMA tube in order to analyze the deformation behavior of ball spinning of NiTi SMA tube.Stress fields,strain fields as well as velocity fields is obtained by means of rigid-viscoplastic FEM,which lays the profound foundations for studying the metal flow rule in ball spinning and forming perfect spun NiTi SMA tube.

  13. Computational Thermodynamics and Kinetics-Based ICME Framework for High-Temperature Shape Memory Alloys

    Science.gov (United States)

    Arróyave, Raymundo; Talapatra, Anjana; Johnson, Luke; Singh, Navdeep; Ma, Ji; Karaman, Ibrahim

    2015-11-01

    Over the last decade, considerable interest in the development of High-Temperature Shape Memory Alloys (HTSMAs) for solid-state actuation has increased dramatically as key applications in the aerospace and automotive industry demand actuation temperatures well above those of conventional SMAs. Most of the research to date has focused on establishing the (forward) connections between chemistry, processing, (micro)structure, properties, and performance. Much less work has been dedicated to the development of frameworks capable of addressing the inverse problem of establishing necessary chemistry and processing schedules to achieve specific performance goals. Integrated Computational Materials Engineering (ICME) has emerged as a powerful framework to address this problem, although it has yet to be applied to the development of HTSMAs. In this paper, the contributions of computational thermodynamics and kinetics to ICME of HTSMAs are described. Some representative examples of the use of computational thermodynamics and kinetics to understand the phase stability and microstructural evolution in HTSMAs are discussed. Some very recent efforts at combining both to assist in the design of HTSMAs and limitations to the full implementation of ICME frameworks for HTSMA development are presented.

  14. Electrical Resistivity-Based Study of Self-Sensing Properties for Shape Memory Alloy-Actuated Artificial Muscle

    Directory of Open Access Journals (Sweden)

    Jian-Ying Zhu

    2013-09-01

    Full Text Available Shape memory alloy (SMA has great potential to develop light and compact artificial muscle (AM due to its muscle-like high power-to-weight ratio, flexibility and silent operation properties. In this paper, SMA self-sensing properties are explored and modeled in depth to imitate the integrated muscle-like functions of actuating and self-sensing for SMA-AM based on the investigation of SMA electrical resistivity (ER. Firstly, an ER transformation kinetics model is proposed based on the simulation of SMA differential scanning calorimetry (DSC curves. Then a series of thermal-electrical-mechanical experiments are carried out to verify the validity of the ER model, whereby the SMA-AM self-sensing function is well established under different stress conditions. Finally the self-sensing capability is further demonstrated by its application to a novel SMA-AM-actuated active ankle-foot orthosis (AAFO.

  15. Electrical resistivity-based study of self-sensing properties for shape memory alloy-actuated artificial muscle.

    Science.gov (United States)

    Zhang, Jian-Jun; Yin, Yue-Hong; Zhu, Jian-Ying

    2013-09-26

    Shape memory alloy (SMA) has great potential to develop light and compact artificial muscle (AM) due to its muscle-like high power-to-weight ratio, flexibility and silent operation properties. In this paper, SMA self-sensing properties are explored and modeled in depth to imitate the integrated muscle-like functions of actuating and self-sensing for SMA-AM based on the investigation of SMA electrical resistivity (ER). Firstly, an ER transformation kinetics model is proposed based on the simulation of SMA differential scanning calorimetry (DSC) curves. Then a series of thermal-electrical-mechanical experiments are carried out to verify the validity of the ER model, whereby the SMA-AM self-sensing function is well established under different stress conditions. Finally the self-sensing capability is further demonstrated by its application to a novel SMA-AM-actuated active ankle-foot orthosis (AAFO).

  16. Electrical Resistivity-Based Study of Self-Sensing Properties for Shape Memory Alloy-Actuated Artificial Muscle

    Science.gov (United States)

    Zhang, Jian-Jun; Yin, Yue-Hong; Zhu, Jian-Ying

    2013-01-01

    Shape memory alloy (SMA) has great potential to develop light and compact artificial muscle (AM) due to its muscle-like high power-to-weight ratio, flexibility and silent operation properties. In this paper, SMA self-sensing properties are explored and modeled in depth to imitate the integrated muscle-like functions of actuating and self-sensing for SMA-AM based on the investigation of SMA electrical resistivity (ER). Firstly, an ER transformation kinetics model is proposed based on the simulation of SMA differential scanning calorimetry (DSC) curves. Then a series of thermal-electrical-mechanical experiments are carried out to verify the validity of the ER model, whereby the SMA-AM self-sensing function is well established under different stress conditions. Finally the self-sensing capability is further demonstrated by its application to a novel SMA-AM-actuated active ankle-foot orthosis (AAFO). PMID:24077316

  17. Rapidly solidified ferromagnetic shape memory alloys

    Science.gov (United States)

    Craciunescu, C. M.; Ercuta, A.; Mitelea, I.; Valeanu, M.; Teodorescu, V. S.; Lupu, N.; Chiriac, H.

    2008-05-01

    Ferromagnetic shape memory alloys have been manufactured by various techniques involving rapid solidification. Bulk alloys have been obtained by extracting the melted alloy in especially designed copper molds; glass coated wires have been obtained by drawing the melt from glass recipients followed by water cooling and ribbons have been fabricated by melt-spinning. Microstructural observations show particular solidification aspects of fractured areas, while ferromagnetic behavior has been detected in glass coated wires obtained by rapid solidification. The martensitic microstructure was observed on Co-Ni-Ga rapid solidified bulk alloys and Fe-Pd ribbons. The memory effect was detected using a Vibran system that allows the detection of the phase transition for the ribbons and by visual observation for other specimens. The conclusions of the observations are related to the comparison between the ferromagnetic behaviors of shape memory alloys solidified using different techniques.

  18. New internalized distraction device for craniofacial plastic surgery using Ni-free, Ti-based shape memory alloy.

    Science.gov (United States)

    Kanetaka, Hiroyasu; Shimizu, Yoshinaka; Kudo, Tada-aki; Zhang, Ye; Kano, Mitsuhiro; Sano, Yuya; Ichikawa, Hiroyuki; Hosoda, Hideki; Miyazaki, Shuichi

    2010-11-01

    This study was undertaken to examine effects and biocompatibility of a new internalized distraction device made from newly developed Ti-Nb-Al shape memory alloy (SMA). Crania of Wistar rats were expanded using a U-shaped wire of this SMA set on each cranium in an experimental group. At 2 or 4 weeks after operation, the rats were killed; width measurements and three-dimensional observations of crania were conducted using soft x-ray and microfocus x-ray computed tomography photography. After photography, histologic sections were made and stained with hematoxylin and eosin. No pathologic change in the experimental duration was observed macroscopically or histologically. Significantly increased size was found for the rat crania in the experimental group compared with the control group. Results demonstrated the feasibility and biocompatibility of internalized distraction osteogenesis using Ni-free, Ti-based SMA in craniofacial plastic surgery for craniofacial deformities.

  19. A 3D finite-strain-based constitutive model for shape memory alloys accounting for thermomechanical coupling and martensite reorientation

    Science.gov (United States)

    Wang, Jun; Moumni, Ziad; Zhang, Weihong; Xu, Yingjie; Zaki, Wael

    2017-06-01

    The paper presents a finite-strain constitutive model for shape memory alloys (SMAs) that accounts for thermomechanical coupling and martensite reorientation. The finite-strain formulation is based on a two-tier, multiplicative decomposition of the deformation gradient into thermal, elastic, and inelastic parts, where the inelastic deformation is further split into phase transformation and martensite reorientation components. A time-discrete formulation of the constitutive equations is proposed and a numerical integration algorithm is presented featuring proper symmetrization of the tensor variables and explicit formulation of the material and spatial tangent operators involved. The algorithm is used for finite element analysis of SMA components subjected to various loading conditions, including uniaxial, non-proportional, isothermal and adiabatic loading cases. The analysis is carried out using the FEA software Abaqus by means of a user-defined material subroutine, which is then utilized to simulate a SMA archwire undergoing large strains and rotations.

  20. Shape Memory Alloy Rock Splitters (SMARS)

    Science.gov (United States)

    Benafan, Othmane (Inventor); Noebe, Ronald D. (Inventor)

    2017-01-01

    Shape memory alloys (SMAs) may be used for static rock splitting. The SMAs may be used as high-energy multifunctional materials, which have a unique ability to recover large deformations and generate high stresses in response to thermal loads.

  1. Mechanocaloric effects in Shape Memory Alloys

    OpenAIRE

    Manosa, Lluis; Planes, Antoni

    2016-01-01

    Shape memory alloys are a class of ferroic materials which undergo a structural (martensitic) transition where the associated ferroic property is a lattice distortion (strain). The sensitiveness of the transition to the conjugated external field (stress), together with the latent heat of the transition gives rise to giant mechanocaloric effects. In non-magnetic shape memory alloys, the lattice distortion is mostly described by a pure shear and the martensitic transition in this family of allo...

  2. Contribution to Shape Memory Alloys Actuated Systems Design

    Directory of Open Access Journals (Sweden)

    Daniel Amariei

    2009-10-01

    Full Text Available Even it has been recognized that Shape Memory Alloys have a significant potential for deployment actuators, the number of applications of SMA-based actuators to the present day is still quite small, due to the need of deep understanding of the thermomechanical behavior of SMA. SMAs offer attractive potentials such as: reversible strains of several percent, generation of high recovery stresses and high power / weight ratios. This paper tries to provide an overview of the shape memory functions. A table with property values for different properties of shape memory alloys is also included

  3. On the widths of the hysteresis of mechanically and thermally induced martensitic transformations in Ni-Ti-based shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, Stefanie; Maass, Burkhard; Frenzel, Jan; Schmidt, Marvin; Ullrich, Johannes; Seelecke, Stefan; Schuetze, Andreas; Kastner, Oliver; Eggeler, Gunther [Bochum Univ. (Germany). Inst. fuer Werkstoffe

    2015-10-15

    It is well known that a good crystallographic compatibility between austenite and martensite in Ni-Ti-based shape memory alloys results in narrow thermal hystereses (e.g. Ball and James, Arch. Ration. Mech. Anal., 1987). The present work suggests that a good crystallographic fit is moreover associated with a small mechanical hysteresis width, observed during a forward and reverse stress-induced transformation. Furthermore, shape memory alloys with a good crystallographic fit show smaller transformation strains. The results obtained in the present study suggest that these correlations are generic and apply to binary Ni-Ti (with varying Ni contents) and quaternary Ni-Ti-Cu-X (X = Cr, Fe, V) alloys. For binary Ni-Ti, it was observed that Ni-rich compositions (good lattice fit) show a lower accumulation of irreversible strains during pseudoelastic cycling.

  4. Application of Shape Memory Alloys in Seismic Isolation: A Review

    Directory of Open Access Journals (Sweden)

    Shaghayegh Alvandi

    2014-12-01

    Full Text Available In the last two decades, there has been an increasing interest in structural engineering control methods. Shape memory alloys and seismic isolation systems are examples of passive control systems that use of any one alone, effectively improve the seismic performance of the structure. Characteristics such as large strain range without any residual deformation, high damping capacity, excellent re-centering, high resistance to fatigue and corrosion and durability have made shape memory alloy an effective damping device or part of base isolators. A unique characteristic of shape memory alloys is in recovering residual deformations even after strong ground excitations. Seismic isolation is a device to lessen earthquake damage prospects. In the latest research studies, shape memory alloy is utilized in combination with seismic isolation system and their results indicate the effectiveness of the application of them to control the response of the structures. This paper reviews the findings of research studies on base isolation system implemented in the building and/or bridge structures by including the unique behavior of shape memory alloys. This study includes the primary information about the characteristic of the isolation system as well as the shape memory material. The efficiency and feasibility of the two mechanisms are also presented by few cases in point.

  5. Medical applications of shape memory alloys

    Directory of Open Access Journals (Sweden)

    Machado L.G.

    2003-01-01

    Full Text Available Shape memory alloys (SMA are materials that have the ability to return to a former shape when subjected to an appropriate thermomechanical procedure. Pseudoelastic and shape memory effects are some of the behaviors presented by these alloys. The unique properties concerning these alloys have encouraged many investigators to look for applications of SMA in different fields of human knowledge. The purpose of this review article is to present a brief discussion of the thermomechanical behavior of SMA and to describe their most promising applications in the biomedical area. These include cardiovascular and orthopedic uses, and surgical instruments.

  6. Shape-Memory-Alloy Release Mechanism

    Science.gov (United States)

    Mckinnis, Darin

    1993-01-01

    Release-nut mechanism activated by electric current applied to shape-memory alloy. Separates attached objects quickly by remote control. Does not create hazard or cause damage. Shape-memory release-nut mechanism unaffected by moisture or vacuum. Requires sustained current lasting 5 seconds or longer, and insensitive to electromagnetic interference. Mechanism can be reused.

  7. A novel training-free cast Fe-Mn-Si-Cr-Ni shape memory alloy based on formation of martensite in a domain-specific manner

    Energy Technology Data Exchange (ETDEWEB)

    Wen, Yuhua; Peng, Huabei; Wang, Chaoping; Yu, Qinxu; Li, Ning [College of Manufacturing Science and Engineering, Sichuan University, Chengdu (China)

    2011-02-15

    The proposed key to producing a good shape memory effect in Fe-Mn-Si alloys is to reduce or even prevent the collisions between martensite bands. A method for realizing this is to make stress-induced martensite bands form in a domain-specific manner. We developed a novel training-free cast Fe-18Mn-5.5Si-9.5Cr-4Ni alloy with residual lathy delta ferrite based on this idea. The recovery strain reached 6.4% only after annealing the cast Fe-18Mn-5.5Si-9.5Cr-4Ni alloy. Microstructure observations indicated that the lathy delta ferrite made the stress-induced martensite form in a domain-specific manner by first subdividing grains into smaller domains. We hypothesize that through adjusting alloy compositions, solidification parameters, and heat treatment technique, the shape recovery of cast Fe-Mn-Si alloys can be further improved. Such a finding will provide a novel method for developing training-free Fe-Mn-Si shape memory alloys. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Challenges and Progress in the Development of High-Temperature Shape Memory Alloys Based on NiTiX Compositions for High-Force Actuator Applications

    Science.gov (United States)

    Padula, Santo, II; Bigelow, Glen; Noebe, Ronald; Gaydosh, Darrell; Garg, Anita

    2006-01-01

    Interest in high-temperature shape memory alloys (HTSMA) has been growing in the aerospace, automotive, process control, and energy industries. However, actual materials development has seriously lagged component design, with current commercial NiTi alloys severely limited in their temperature capability. Additions of Pd, Pt, Au, Hf, and Zr at levels greater than 10 at.% have been shown to increase the transformation temperature of NiTi alloys, but with few exceptions, the shape memory behavior (strain recovery) of these NiTiX systems has been determined only under stress free conditions. Given the limited amount of basic mechanical test data and general lack of information regarding the work attributes of these materials, a program to investigate the mechanical behavior of potential HTSMAs, with transformation temperatures between 100 and 500 C, was initiated. This paper summarizes the results of studies, focusing on both the practical temperature limitations for ternary TiNiPd and TiNiPt systems based on the work output of these alloys and the ability of these alloys to undergo repeated thermal cycling under load without significant permanent deformation or "walking". These issues are ultimately controlled by the detwinning stress of the martensite and resistance to dislocation slip of the individual martensite and austenite phases. Finally, general rules that govern the development of useful, high work output, next-generation HTSMA materials, based on the lessons learned in this work, will be provided

  9. A jumping shape memory alloy under heat.

    Science.gov (United States)

    Yang, Shuiyuan; Omori, Toshihiro; Wang, Cuiping; Liu, Yong; Nagasako, Makoto; Ruan, Jingjing; Kainuma, Ryosuke; Ishida, Kiyohito; Liu, Xingjun

    2016-02-16

    Shape memory alloys are typical temperature-sensitive metallic functional materials due to superelasticity and shape recovery characteristics. The conventional shape memory effect involves the formation and deformation of thermally induced martensite and its reverse transformation. The shape recovery process usually takes place over a temperature range, showing relatively low temperature-sensitivity. Here we report novel Cu-Al-Fe-Mn shape memory alloys. Their stress-strain and shape recovery behaviors are clearly different from the conventional shape memory alloys. In this study, although the Cu-12.2Al-4.3Fe-6.6Mn and Cu-12.9Al-3.8Fe-5.6Mn alloys possess predominantly L2(1) parent before deformation, the 2H martensite stress-induced from L2(1) parent could be retained after unloading. Furthermore, their shape recovery response is extremely temperature-sensitive, in which a giant residual strain of about 9% recovers instantly and completely during heating. At the same time, the phenomenon of the jumping of the sample occurs. It is originated from the instantaneous completion of the reverse transformation of the stabilized 2H martensite. This novel Cu-Al-Fe-Mn shape memory alloys have great potentials as new temperature-sensitive functional materials.

  10. Fatigue Resistance of Liquid-assisted Self-repairing Aluminum Alloys Reinforced with Shape Memory Alloys

    Science.gov (United States)

    Wright, M. Clara; Manuel, Michele; Wallace, Terryl

    2013-01-01

    A self-repairing aluminum-based composite system has been developed using a liquid-assisted healing theory in conjunction with the shape memory effect of wire reinforcements. The metal-metal composite was thermodynamically designed to have a matrix with a relatively even dispersion of a low-melting eutectic phase, allowing for repair of cracks at a predetermined temperature. Additionally, shape memory alloy (SMA) wire reinforcements were used within the composite to provide crack closure. Investigators focused the research on fatigue cracks propagating through the matrix in order to show a proof-of-concept Shape Memory Alloy Self-Healing (SMASH) technology for aeronautical applications.

  11. Silver- and Zirconium-added ternary and quaternary TiAu based high temperature shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wadood, A., E-mail: abdul.wadood@ist.edu.pk [High Temperature Materials Unit, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Department of Materials Science and Engineering, Institute of Space Technology (IST), Near Rawat Toll Plaza, Islamabad (Pakistan); Yamabe-Mitarai, Y. [High Temperature Materials Unit, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan)

    2015-10-15

    Low strength in B2 phase, incomplete shape memory effect and high cost of Au are obstacles for the use of Ti–50Au as a high temperature shape memory alloy. We investigated the effects of partial substitution of Ti with Zr and Au with Ag in Ti–Au on phase constitution, phase transformation, and high temperature thermo-mechanical and shape memory properties. Partial substitution of Ti with Zr in Ti–50Au and Ti–40Au–10Ag was found to improve the thermo-mechanical and shape memory effect. However, partial substitution of Au with Ag in Ti–50Au and Ti–50Au–10Zr was found to have negligible effects. Reasons for such different behavior of Zr- and Ag-added Ti–Au alloys are considered. - Highlights: • Au, Ag and Ti, Zr belong to same group. Effects of partial substitution of Au with Ag and Ti with Zr in Ti–Au are investigated. • Zr was found more effective than Ag in improving shape memory and mechanical properties. • Same atomic size of Au and Ag and large size misfit b/w Ti and Zr atoms. • Ag resulted large amount of precipitation in Ti–Au.

  12. Grain size effect on the structural parameters of the stress induced epsilonhcp: martensite in iron-based shape memory alloy

    Directory of Open Access Journals (Sweden)

    Fabiana Cristina Nascimento

    2008-03-01

    Full Text Available The aim of this work was to study the effect of austenitic grain size (GS reduction on the structural parameters of the epsilonhcp - martensite in stainless shape memory alloy (SMA. Rietveld refinement data showed an expansion in c-axis and a reduction in a and b-axis with thermo-mechanical cycles for all samples analyzed. Samples with 75 < GS (µm < 129 were analyzed. It was also observed an increase of the unit cell volume in this phase with GS reduction. The smallest grain size sample (GS = 75 µm presented a c/a ratio of 1.649, and approximately 90% of total shape memory recovery.

  13. Large field-induced irreversibility in Ni-Mn based Heusler shape-memory alloys: A pulsed magnetic field study

    Science.gov (United States)

    Nayak, A. K.; Mejia, C. Salazar; D'Souza, S. W.; Chadov, S.; Skourski, Y.; Felser, C.; Nicklas, M.

    2014-12-01

    We present a pulsed magnetic field study on the magnetic and magnetostriction properties of Ni-Mn-Z (Z =In , Sn, and Sb) based Heusler shape-memory alloys. These materials generally display a field-induced magnetostructural transition that could lead to an irreversible phase transition, when measured near the martensitic transition temperature. Here, we show that independently of the transition temperature, the critical field for the phase transition sensitively depends on the main-group element in the sample. Irrespective of their compositions, all samples display a magnetization of around 2 μB/f .u . in the martensite phase and about 6 μB/f .u . in the cubic austenite phase. Our magnetic and magnetostriction measurements at low temperatures exhibit a partial or complete arrest of the high-field austenite phase below the reverse martensitic transition. This results in a large irreversibility with a hysteresis width as high as 24 T. We introduce a theoretical model to discuss the experimental results.

  14. Control devices incorporated with shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    Xue Suduo; Li Xiongyan

    2007-01-01

    Shape Memory Alloy (SMA) is a type of material that offers some unique characteristics for use in devices for vibration control applications. Based on SMA's material properties, four types of control devices that incorporate NiTi SMA wires are introduced in this paper, which include three types of dampers (SMA damper, SMA-MR damper and SMA-friction damper) and one kind of isolation bearing (SMA-rubber bearing). Mechanical models of these devices and their experimental verifications are presented. To investigate the control performance of these devices, the SMA-MR damper and SMA-rubber bearing are applied to structures. The results show that the control devices could be effective in reducing the seismic response of structures.

  15. Design and development of NiTi-based precipitation-strengthened high-temperature shape memory alloys for actuator applications

    Science.gov (United States)

    Hsu, Derek Hsen Dai

    As a vital constituent in the field of smart materials and structures, shape memory alloys (SMAs) are becoming ever-more important due to their wide range of commercial and industrial applications such as aircraft couplings, orthodontic wires, and eyeglasses frames. However, two major obstacles preventing SMAs from fulfilling their potential as excellent actuator materials are: 1) the lack of commercially-viable SMAs that operate at elevated temperatures, and 2) the degradation of mechanical properties and shape memory behavior due to thermal cyclic fatigue. This research utilized a thermodynamically-driven systems design approach to optimize the desired properties by controlling the microstructure and processing of high-temperature SMAs (HTSMAs). To tackle the two aforementioned problems with HTSMAs, the introduction of Ni2TiAl coherent nanoprecipitates in a Ni-Ti-Zr/Hf HTSMA matrix is hypothesized to strengthen the martensite phase while simultaneously increasing the transformation temperature. Differential scanning calorimetry (DSC) was used to determine the transformation temperatures and thermal cyclic stability of each alloy. Also, microstructural characterization was performed using X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom probe tomography (APT). Lastly, compression testing was used to assess the mechanical behavior of the alloys. From the investigation of the first set of Ni48.5Ti31.5-X Zr20AlX (X = 0, 1, 2, 3) prototype alloys, Al addition was found to decrease the transformation temperatures, decrease the thermal cyclic stability, but also increase the strength due to the nucleation and growth of embrittling NiTi2 and NiTiZr Laves phases. However, the anticipated Heusler phase precipitation did not occur. The next study focused on Ni50Ti30-XHf20Al X (X = 0, 1, 2, 3, 4, 5) prototype alloys which replaced Zr with Hf to avoid the formation of brittle Laves phases

  16. Development of laminated nanocomposites on the bases of magnetic and non-magnetic shape memory alloys: Towards new tools for nanotechnology

    Energy Technology Data Exchange (ETDEWEB)

    Irzhak, Artemy [National University of Science and Technology “MISiS”, Moscow (Russian Federation); Koledov, Viktor [Kotelnikov Institute of Radioengineering and Electronics of the Russian Academy of Sciences, Moscow (Russian Federation); Zakharov, Dmitry, E-mail: dmitry.zakharov@misis.ru [National University of Science and Technology “MISiS”, Moscow (Russian Federation); Lebedev, Gor [National University of Science and Technology “MISiS”, Moscow (Russian Federation); Mashirov, Alexey; Afonina, Veronika; Akatyeva, Kristina; Kalashnikov, Vladimir [Kotelnikov Institute of Radioengineering and Electronics of the Russian Academy of Sciences, Moscow (Russian Federation); Sitnikov, Nikolay [National Research Nuclear University “MEPhI”, Moscow (Russian Federation); Tabachkova, Natalia [National University of Science and Technology “MISiS”, Moscow (Russian Federation); Shelyakov, Alexander [National Research Nuclear University “MEPhI”, Moscow (Russian Federation); Shavrov, Vladimir [Kotelnikov Institute of Radioengineering and Electronics of the Russian Academy of Sciences, Moscow (Russian Federation)

    2014-02-15

    Highlights: ► New results on the recently developed shape memory nanocomposites are reported. ► Impact of FIB fabrication method on shape memory properties was studied. ► Shape memory effect for Ti{sub 2}NiCu sample prepared by FIB vanishes at thickness between 70 nm and 170 nm. ► Ni{sub 2}MnGa-based magnetic microcomposite was fabricated and tested for the first time. -- Abstract: New composite functional material with shape memory effect (SME) has recently been proposed and tested for actuation on microscale. The composite nanotweezers have been designed and tested in manipulation of nano-objects. This report presents the new experiments on shape memory alloy’s (SMAs) properties on submicron scale of dimensions and the development of the technology of nanomanipulation on their bases. The minimal thickness of shape memory layer that undergoes SME was experimentally estimated for Ti{sub 2}NiCu alloy. Impact of the focused ion beam modification of SMA superficial layer on the shape memory properties of micro-sized samples is discussed. Composite actuator of Ni–Mn–Ga magnetic SMA with the size of 20 × 4 × 2 μm{sup 3} was fabricated for the first time and its thermal actuation was experimentally demonstrated ( (http://www.smwsm.org/microactuators/NiMnGa.html))

  17. High-Temperature Shape Memory Alloys

    Science.gov (United States)

    Biffi, C. A.; Tuissi, A.

    2014-10-01

    In this paper, an experimental study of laser micro-processing on a Cu-Zr-based shape memory alloy (SMA), which is suitable for high-temperature (HT) applications, is discussed. A first evaluation of the interaction between a laser beam and Zr50Cu28Ni7Co15 HT SMA is highlighted. Single laser pulses at various levels of power and pulse duration were applied to evaluate their effect on the sample surfaces. Blind and through microholes were produced with sizes on the order of a few hundreds of microns; the results were characterized from the morphological viewpoint using a scanning electron microscope. The high beam quality allows the holes to be created with good circularity and little melted material around the hole periphery. An analysis of the chemical composition was performed using energy dispersive spectroscopy, revealing that compositional changes were limited, while important oxidation occurred on the hole surfaces. Additionally, laser micro-cutting tests were also proposed to evaluate the cut edge morphology and dimensions. The main result of this paper concerned the good behavior of the material upon interaction with the laser beam, which suggests that microfeatures can be successfully produced in this alloy.

  18. ESTIMATION OF LOCAL HYSTERETIC PROPERTIES FOR SHAPE MEMORY ALLOYS

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The applicability of shape memory alloys (SMAs) in structural dynamics, particularly as hysteretic damping elements, is limited by the difficulties in modelling their deformation characteristics. At typical engineering design levels of loading SMAs exhibit pseudo-elastic properties. A combined experimental and simulation approach suitable for the characterisation of novel smart devices based on the pseudo-elastic effect is described.

  19. Shape-Memory-Alloy Actuator For Flight Controls

    Science.gov (United States)

    Barret, Chris

    1995-01-01

    Report proposes use of shape-memory-alloy actuators, instead of hydraulic actuators, for aerodynamic flight-control surfaces. Actuator made of shape-memory alloy converts thermal energy into mechanical work by changing shape as it makes transitions between martensitic and austenitic crystalline phase states of alloy. Because both hot exhaust gases and cryogenic propellant liquids available aboard launch rockets, shape-memory-alloy actuators exceptionally suited for use aboard such rockets.

  20. Inconvenient magnetocaloric effect in ferromagnetic shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Khovaylo, Vladimir, E-mail: khovaylo@misis.ru [National University of Science and Technology “MISiS”, Moscow 119049 (Russian Federation)

    2013-11-15

    Highlights: ► Critical analysis of the available experimental results on isothermal magnetic entropy change in ferromagnetic shape memory alloys Ni–Mn–X (X = Ga, In, Sn, Sb) is given. ► Based on available in literature experimental data on total entropy change at martensitic transformation it is shown that the isothermal magnetic entropy change in Ni–Mn–X (X = Ga, In, Sn, Sb) should not greatly exceed 30 J/kg K. -- Abstract: Critical analysis available in the literature experimental results on magnetocaloric effect in ferromagnetic shape memory alloys Ni–Mn–X (X = Ga, In, Sn, Sb) is given. Based on a model developed by Pecharsky et al. [22], it is shown that the isothermal magnetic field-induced entropy change in the Ni–Mn–X alloys should not greatly exceed 30 J/kg K. Considering thermodynamics of temperature- and magnetic field-induced martensitic transformations, it is demonstrated that a contribution of the structural subsystem to the magnetocaloric effect in the Ni–Mn–X alloys studied so far is irreversible in magnetic fields below 5 T. This makes ferromagnetic shape memory alloys an inconvenient system for the practical application in modern magnetic refrigeration technology.

  1. Obtaining shape memory alloy thin layer using PLD technique

    Directory of Open Access Journals (Sweden)

    Cimpoeşu N.

    2014-01-01

    Full Text Available Copper-based shape memory alloy (SMA was obtained through a classic melting method. The material was analyzed in heat treated and deformed states using scanning electrons microscopy (SEM, dilatometry (DIL, differential scanning calorimetry (DSC, dynamic mechanical analyzer (DMA and energy dispersive X-ray analyze (EDAX to establish the material microstructure, memory properties like martensitic transformation domain and rate or damping capacity. The material exhibits a good shape memory effect and high internal friction and it is proposed as target in a pulsed laser deposition (PLD process for obtaining thin films. The deposition process is described in this paper through presented experimental results on the layer.

  2. Fracture Behavior of TiNi Based Shape Memory Alloy Cold-rolled Tube

    Institute of Scientific and Technical Information of China (English)

    LI Yan-wu; LIU Fu-shun

    2006-01-01

    The microstructures and interfacial characteristics of matrices at the inwalls and the out-walls of the cold-rolled tube with different amounts of deformation were investigated by the scanning electronic microscope (SEM), the optical microscope (OM), and the transmission electronic microscope (TEM) techniques. It was observed that as the amount of deformation increases, the flaws nucleate at the out-walls of the cold rolled tube, the stress-induced martensites change from (11) type Ⅰ twins to (011) type Ⅱ twins and then to (100) compound twins, nanocrystals and bulk amorphisation happen, the high density dislocation causes stress concentration at the out-walls of the Ti50Ni50 cold-rolled tube, and then precipitates its fracture, and the Ti2Ni particles strengthen the grain boundaries and curb the dislocation movements during plastic deformation. The inhomogeneity level of the grains in the Ti50Ni50 alloy plays an important role on the fracture of the Ti50Ni50 cold rolled tube.

  3. Design of Fatigue Resistant Heusler-strengthened PdTi-based Shape Memory Alloys for Biomedical Applications

    Science.gov (United States)

    Frankel, Dana J.

    The development of non-surgical transcatheter aortic valve implantation (TAVI) techniques, which utilize collapsible artificial heart valves with shape memory alloy (SMA)-based frames, pushes performance requirements for biomedical SMAs beyond those for well-established vascular stent applications. Fatigue life for these devices must extend into the ultra-high cycle fatigue (UHCF) regime (>600M cycles) with zero probability of failure predicted at applied strain levels. High rates of Ni-hypersensitivity raise biocompatibility concerns, driving the development of low-Ni and Ni-free SMAs. This work focuses on the development of biocompatible, precipitation-strengthened, fatigue-resistant PdTi-based SMAs for biomedical applications. Functional and structural fatigue are both manifestations of cyclic instability resulting in accumulation of slip and eventual structural damage. While functional fatigue is easily experimentally evaluated, structural fatigue is more difficult to measure without the proper equipment. Therefore, in this work a theoretical approach using a model well validated in steels is utilized to investigate structural fatigue behavior in NiTi in the UHCF regime, while low cycle functional fatigue is evaluated in order to monitor the core phenomena of the cyclic instability. Results from fatigue simulations modeling crack nucleation at non-metallic inclusions in commercial NiTi underscore the importance of increasing yield strength for UHCF performance. Controlled precipitation of nanoscale, low-misfit, L21 Heusler aluminides can provide effective strengthening. Phase relations, precipitation kinetics, transformation temperature, transformation strain, cyclic stability, and mechanical properties are characterized in both Ni-free (Pd,Fe)(Ti,Al) and low-Ni high-strength "hybrid" (Pd,Ni)(Ti,Zr,Al) systems. Atom probe tomography is employed to measure phase compositions and particle sizes used to calibrate LSW models for coarsening kinetics and Gibbs

  4. Precipitation Hardenable High Temperature Shape Memory Alloy

    Science.gov (United States)

    Noebe, Ronald Dean (Inventor); Draper, Susan L. (Inventor); Nathal, Michael V. (Inventor); Crombie, Edwin A. (Inventor)

    2010-01-01

    A composition of the invention is a high temperature shape memory alloy having high work output, and is made from (Ni+Pt+Y),Ti(100-x) wherein x is present in a total amount of 49-55 atomic % Pt is present in a total amount of 10-30 atomic %, Y is one or more of Au, Pd. and Cu and is present in a total amount of 0 to 10 atomic %. The alloy has a matrix phase wherein the total concentration of Ni, Pt, and the one or more of Pd. Au, and Cu is greater than 50 atomic %.

  5. Excess Ni-doping induced enhanced room temperature magneto-functionality in Ni-Mn-Sn based shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Pramanick, S.; Giri, S.; Majumdar, S., E-mail: sspsm2@iacs.res.in [Department of Solid State Physics, Indian Association for the Cultivation of Science, 2A and B Raja S. C. Mullick Road, Jadavpur, Kolkata 700 032 (India); Chatterjee, S. [UGC-DAE Consortium for Scientific Research, Kolkata Centre, Sector III, LB-8, Salt Lake, Kolkata 700 098 (India)

    2014-09-15

    Present work reports on the observation of large magnetoresistance (∼−30% at 80 kOe) and magnetocaloric effect (∼12 J·kg{sup −1}·K{sup −1} for 0–50 kOe) near room temperature (∼290 K) on the Ni-excess ferromagnetic shape memory alloy Ni{sub 2.04}Mn{sub 1.4}Sn{sub 0.56}. The sample can be thought of being derived from the parent Ni{sub 2}Mn{sub 1.4}Sn{sub 0.6} alloy, where excess Ni was doped at the expense of Sn. Such Ni doping enhances the martensitic transition temperature and for the Ni{sub 2.04}Mn{sub 1.4}Sn{sub 0.56} it is found to be optimum (288 K). The doped alloy shows enhanced magneto-functional properties as well as reduced saturation magnetization as compared to the undoped counterpart at low temperature. A probable increment of antiferromagnetic correlation between Mn-atoms on Ni substitution can be accounted for the enhanced magneto-functional properties as well as reduction in saturation moment.

  6. Effects of Annealing on the Martensitic Transformation of Ni-Based Ferromagnetic Shape Memory Heusler Alloys and Nanoparticles

    OpenAIRE

    Tina Fichtner; Changhai Wang; Aleksandr A. Levin; Guido Kreiner; Catalina Salazar Mejia; Simone Fabbrici; Franca Albertini; Claudia Felser

    2015-01-01

    We report on the effects of annealing on the martensitic phase transformation in the Ni-based Heusler system: Mn50Ni40Sn10 and Mn50Ni41Sn9 powder and Co50Ni21Ga32 nanoparticles. For the powdered Mn50Ni40Sn10 and Mn50Ni41Sn9 alloys, structural and magnetic measurements reveal that post-annealing decreases the martensitic transformation temperatures and increases the transition hysteresis. This might be associated with a release of stress in the Mn50Ni40Sn10 and Mn50Ni41Sn9 alloys during the an...

  7. A macro-mechanical constitutive model of shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    It is of practical interest to establish a precise constitutive model which includes the equations describing the phase transformation behaviors and thermo-mechanical processes of shape memory alloy (SMA). The microscopic mechanism of super elasticity and shape memory effect of SMA is explained based on the concept of shape memory factor defined by the author of this paper. The conventional super elasticity and shape memory effect of SMA are further unified as shape memory effect. Shape memory factor is redefined in order to make clear its physical meaning. A new shape memory evolution equation is developed to predict the phase transformation behaviors of SMA based on the differential relationship between martensitic volume fraction and phase transformation free energy and the results of DSC test. It overcomes the limitations that the previous shape memory evolution equations or phase transformation equations fail to express the influences of the phase transformation peak temperatures on the phase transformation behaviors and the transformation from twinned martensite to detwinned martensite occurring in SMA. A new macro-mechanical constitutive equation is established to predict the thermo-mechanical processes realizing the shape memory effect of SMA from the expression of Gibbs free energy. It is expanded from one-dimension to three-dimension with assuming SMA as isotropic material. All material constants in the new constitutive equation can be determined from macroscopic experiments, which makes it more easily used in practical applications.

  8. A macro-mechanical constitutive model of shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    ZHOU Bo; LIU YanJu; LENG JinSong; ZOU GuangPing

    2009-01-01

    It is of practical interest to establish a precise constitutive model which includes the equations de-scribing the phase transformation behaviors and thermo-mechanical processes of shape memory alloy (SMA).The microscopic mechanism of super elasticity and shape memory effect of SMA is explained based on the concept of shape memory factor defined by the author of this paper.The conventional super elasticity and shape memory effect of SMA are further unified as shape memory effect.Shape memory factor is redefined in order to make clear its physical meaning.A new shape memory evolution equation is developed to predict the phase transformation behaviors of SMA based on the differential relationship between martensitic volume fraction and phase transformation free energy and the results of DSC test.It overcomes the limitations that the previous shape memory evolution equations or phase transformation equations fail to express the influences of the phase transformation peak temperatures on the phase transformation behaviors and the transformation from twinned martensite to detwinned martensite occurring in SMA.A new macro-mechanical constitutive equation is established to predict the thermo-mechanical processes realizing the shape memory effect of SMA from the expression of Gibbs free energy.It is expanded from one-dimension to three-dimension with assuming SMA as iso-tropic material.All material constants in the new constitutive equation can be determined from mac-roscopic experiments,which makes it more easily used in practical applications.

  9. Alloying and Casting Furnace for Shape Memory Alloys Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The concept in the proposed project is to create a melting, alloying and casting furnace for the processing titanium based SMA using cold crucible techniques. The...

  10. Shape memory alloys – characterization techniques

    Indian Academy of Sciences (India)

    Jayagopal Uchil

    2002-05-01

    Shape memory alloys are the generic class of alloys that show both thermal and mechanical memory. The basic physics involved in the shape memory effect is the reversible thermoelastic martensitic transformation. In general, there exists two phases in shape memory alloys, viz., a hightemperature phase or austenitic phase (A) and a low-temperature phase or martensitic phase (M). In addition, an intermediate R phase exists in some special cases. The M ↔ A transformation is associated with a recoverable strain of about 6.5–8% and the R ↔ A transformation is associated with a recoverable strain of about 1%. The former transformation has been widely used in the applications like antenna deployment of satellite, aerospace couplings, orthodontic arch wires, medical guide wires for diagnostic and therapeutic catheters and other industrial applications. Our group has been giving emphasis to the characterization techniques for R phase, using differential scanning calorimetry (DSC), electrical resistivity probe (ER) and thermomechanical analyzer (TMA). R phase is found to have attractive features like stability against thermal cycling, a small thermal hysteresis and a negligible strain recovery fatigue. DSC has been used successfully to characterize the recoverable strain parameters, apart from the determination of transformation temperatures. ER is used, for the systematic study of the dependence of various phases on heat-treatment temperatures. TMA has been effectively employed for the study of the mixed phases. A space-rotating platform is designed and fabricated, using an actuator of shape memory spring, for obtaining controlled rotations. The efficiency and the reliability of this actuator has been tested, over a million thermal cycles.

  11. Design for the Damping of a Railway Collector Based on the Application of Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    M. Bocciolone

    2012-01-01

    Full Text Available A new design of a Cu based SMA/GFRP lateral horn of a railway collector is proposed. Synergistic contribution of the performance parameters associated with the SMA, including specific damping, specific stiffness, and volume fraction, as well as those associated with the host composite such as flexural rigidity, SMA through-the-thickness location, and SMA-host interfacial strength, is taken into account. The aim is to increase the structural damping of the first flexural mode of the horn without significantly changing its flexural stiffness and weight. The focus of this work also applies to manufacturability and the cost effectiveness of the component for future industrial production.

  12. Shape Memory Alloy Isolation Valves: Public Quad Chart

    Science.gov (United States)

    2017-05-12

    NUMBER (Include area code) 12 May 2017 Briefing Charts 12 April 2017 - 12 May 2017 Shape Memory Alloy Isolation Valves: Public Quad Chart William...spacecraft (15+ yrs) • Shaped memory alloy isolation valves provide an intrinsically safe isolation system that increases lifetime >5x over SOTA and... Shape Memory Alloy Isolation Valves POC: W. Hargus, Ph.D., AFRL/RQRC B-52 Teardrop Antenna Depolymerization WC-130J Leading Edge Erosion Distribution

  13. Competition between invariant habit plane and compatible junction plane in TiNb-based shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Inamura, T., E-mail: inamura.t.aa@m.titech.ac.jp [Precision and Intelligence Laboratory, Tokyo Institute of Technology (Japan); Kim, H.Y. [Institute of Materials Science, University of Tsukuba (Japan); Hosoda, H. [Precision and Intelligence Laboratory, Tokyo Institute of Technology (Japan); Miyazaki, S. [Institute of Materials Science, University of Tsukuba (Japan)

    2013-11-15

    Highlights: ► Kinematic compatibility (KC) among martensite variants in Ti-Nb-Al is evaluated. ► Rotation Q is necessary to keep KC at any junction plane (JP). ► The rotation Q is equivalent to the rotation to form the exact twin-relationship. ► The JP preferentially observed in experiment is the JP with the smaller Q. ► We propose two preferential JPs with {1 1 1} type I and 〈2 1 1〉 type II twin in Ti-Nb-Al. -- Abstract: The invariant plane (IP) condition at a habit plane (HP) and the kinematic compatibility (KC) condition at a junction plane (JP) are quantitatively evaluated by the geometrically nonlinear theory of martensite and the origin of the twin orientation relationship (OR) at a JP is revealed in a β titanium shape memory alloy. Exact twin OR at a JP is impossible among the habit plane variants (HPVs). A nonzero rotation is necessary to maintain the compatibility at a JP between the HPVs. The fully compatible HPV cluster in which IP at a HP and KC at a JP are maintained simultaneously is impossible in this alloy. However, it was found that twin OR and KC can be maintained simultaneously. The preferentially observed HPV clusters in transmission electron microscopy are the clusters with a smaller rotation to maintain KC at a JP.

  14. Thickness-dependent electronic structure modulation of ferromagnetic films on shape memory alloy substrates based on a pure strain effect

    Science.gov (United States)

    Feng, Chun; Hu, Di; Gong, Kui; Jiang, Xumin; Yin, Jianjuan; Cao, Yi; Tang, Xiao-Lei; Yang, Feng; Zhou, Zhongfu; Yu, Guanghua; Andrew Evans, D.

    2016-11-01

    Pure strain-induced electronic structure modulation in ferromagnetic films is critical for developing reliable strain-assisted spintronic devices with low power consumption. For the conventional electricity-controlled strain engineering, it is difficult to reveal the pure strain effect on electronic structure tunability due to the inseparability of pure strain effect and surface charge effect. Here, a non-electrically controlled NiTi shape memory alloy was utilized as a strain output substrate to induce a pure strain on attached Fe films through a thermally controlled shape memory effect. The pure strain induced electronic structure evolution was revealed by in-situ X-ray photoelectron spectroscopy and correlated with first-principles calculations and magnetic anisotropy measurements. A compressive strain enhances the shielding effect for core electrons and significantly tunes their binding energy. Meanwhile, the strain modifies the partial density of states of outer d orbits, which may affect spin-orbit coupling strength and related magnetic anisotropy. This work helps for clarifying the physical nature of the pure strain effect and developing the pure-strain-assisted spintronic devices.

  15. Grain Constraint and Size Effects in Shape Memory Alloy Microwires

    Science.gov (United States)

    Ueland, Stian Melhus

    Shape memory alloys exhibit interesting and useful properties, such as the shape memory effect and superelasticity. Among the many alloy families that have been shown to exhibit shape memory properties the ones based on copper are interesting because they are relatively inexpensive and show excellent properties when made as single crystals. However, the performance ofthese alloys is severely compromised by the introduction of grain boundaries, to the point where they are too poor for commercial applications. This thesis studies the mechanical properties of fine Cobased wires with a bamboo microstructure, i.e., where triple junctions are absent and grain boundaries run perpendicular to the wire axis. These microwires are not single crystals, but their microstructure is not as complex as that of polycrystals either: we call this new class of shape memory alloys oligocrystals. This thesis seeks to better understand the relationship between microstructure and properties in these alloys through a combination of mechanical testing, in situ experiments and modeling. First, in situ scanning electron microscopy, together with finite element modeling, is used to understand the role of grain constraint on the martensitic transformation. Grain constraints are observed to be much less severe in oligocrystalline wires as compared to polycrystals. Oligocrystalline microwires are then thermomechanically tested and shown to exhibit excellent properties that approach those of single crystals. Next, property evolution during cycling is investigated, revealing training effects as well as fatigue life and fracture. Finally, size effects in damping and transformation morphology are studied and it is shown that a transition from a many-domain to a single domain martensite morphology takes place when the wire diameter is decreased. (Copies available exclusively from MIT Libraries, libraries.mit.edu/docs - docs@mit.edu)

  16. Flexible Robotic Spine Actuated by Shape Memory Alloy

    OpenAIRE

    2014-01-01

    A flexible robotic spine actuated by shape memory alloy (SMA) can achieve both bending motion and impact absorption, which will allow robots to realize a variety of postures. In this paper, the robotic spine is designed and simplified into a multi-segment dynamic model based on several verified assumptions. The SMA wire is modelled using the Seelecke-Muller-Acenbach theory. An iterative algorithm is developed to address the external forces distributed along the spine and compute the spine’s b...

  17. Grain size effect on the thermal-induced martensitic transformation in polycrystalline Cu-based shape memory alloys

    OpenAIRE

    la Roca, Paulo Matías; Isola, Lucio Manuel; Sobrero, Cesar Enrique; Vermaut, P.; Malarria, Jorge Alberto

    2016-01-01

    In Cu-based SMA alloys, the grain size (d) effect on the martensitic transformation temperature was investigated for a wide range of d. Specimens were prepared by different heat treatments in order to create a range of grain sizes, from about 500 nm (ribbons and tapes obtained by rapid solidification techniques) up to 6 mm diameter single-crystals (grown by the Bridgman method). Information obtained from the literature was also included in the set of analyzed experimental data. The reduction ...

  18. Role of alloying additions on the properties of Cu–Al–Mn shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Dasgupta, Rupa, E-mail: rupadasgupta@ampri.res.in; Jain, Ashish Kumar; Kumar, Pravir; Hussain, Shahadat; Pandey, Abhishek

    2015-01-25

    Highlights: • Cu based SMAs with high transition temperature could be made using LM route. • The properties depend on alloying composition. • Property characterisation establishes feasibility of making SMAs. - Abstract: The effect of alloying seven different elements [Zn, Si, Fe, Ni, Mg, Cr and Ti] on the microstructure, hardness, phase precipitation and transformation temperature in a Cu–12.5Al–5Mn alloy with a view to possible improvements as a result of these additions is the focus of the reported study. The base alloy has been chosen keeping in mind its ability to exhibit shape memory properties and improved ductility over other Cu-based SMAs. The objective was to ascertain changes or improvements attained due to the individual tertiary additions. The samples were prepared through liquid metallurgy route using pure copper, aluminum, manganese and the respective quaternary alloying elements in right quantities to weigh 1000 g of the alloy in total and were melted together. Samples from the cast alloys were subject to homogenisation treatment at 200 °C for 2 h in a muffle furnace and furnace cooled. Samples from the homogenised alloys were heated and held for 2 h at 920 °C followed by ice quenching to obtain the desired martensitic structure for shape memory behaviour. The alloys in the cast, homogenised and quenched conditions were metallographically polished to observe the martensitic phase formation mainly in quenched samples which is a pre requisite for exhibiting shape memory properties in these alloys. X-ray Diffraction studies were carried out on the cast and quenched samples using Cu Kα target; and the phases identified indicate martensitic phase precipitation; however in some cases the precipitation is incomplete. Differential Scanning Calorimetric [DSC] studies were carried out on quenched samples from room temperature to 600 °C maintaining a constant rate of 10 °C/min. Results indicate clear transformation peaks in all the samples which

  19. Mechanocaloric effects in shape memory alloys.

    Science.gov (United States)

    Mañosa, Lluís; Planes, Antoni

    2016-08-13

    Shape memory alloys (SMA) are a class of ferroic materials which undergo a structural (martensitic) transition where the associated ferroic property is a lattice distortion (strain). The sensitiveness of the transition to the conjugated external field (stress), together with the latent heat of the transition, gives rise to giant mechanocaloric effects. In non-magnetic SMA, the lattice distortion is mostly described by a pure shear and the martensitic transition in this family of alloys is strongly affected by uniaxial stress, whereas it is basically insensitive to hydrostatic pressure. As a result, non-magnetic alloys exhibit giant elastocaloric effects but negligible barocaloric effects. By contrast, in a number of magnetic SMA, the lattice distortion at the martensitic transition involves a volume change in addition to the shear strain. Those alloys are affected by both uniaxial stress and hydrostatic pressure and they exhibit giant elastocaloric and barocaloric effects. The paper aims at providing a critical survey of available experimental data on elastocaloric and barocaloric effects in magnetic and non-magnetic SMA.This article is part of the themed issue 'Taking the temperature of phase transitions in cool materials'.

  20. Three-Dimensional Cellular Structures Enhanced By Shape Memory Alloys

    Science.gov (United States)

    Nathal, Michael V.; Krause, David L.; Wilmoth, Nathan G.; Bednarcyk, Brett A.; Baker, Eric H.

    2014-01-01

    This research effort explored lightweight structural concepts married with advanced smart materials to achieve a wide variety of benefits in airframe and engine components. Lattice block structures were cast from an aerospace structural titanium alloy Ti-6Al-4V and a NiTi shape memory alloy (SMA), and preliminary properties have been measured. A finite element-based modeling approach that can rapidly and accurately capture the deformation response of lattice architectures was developed. The Ti-6-4 and SMA material behavior was calibrated via experimental tests of ligaments machined from the lattice. Benchmark testing of complete lattice structures verified the main aspects of the model as well as demonstrated the advantages of the lattice structure. Shape memory behavior of a sample machined from a lattice block was also demonstrated.

  1. Characterization Results of a Novel Shape Memory Alloy

    Science.gov (United States)

    Collado, M.; Nava, N.; Herranz, S.; Ramiro, C.; San Juan, J. M.; Patti, S.; Lautier, J.-M.

    2012-07-01

    A novel Shape Memory Alloy (SMA) has been developed as an alternative to currently available alloys. This material, called SMARQ, shows a higher working range of temperatures with respect to the SMA materials used until now, mainly NiTi based alloys. SMARQ is a fully European material technology and production processes, which allows the manufacture of high quality products, with tuneable transformation temperatures up to 200oC. A full Characterization test campaign has been completed in order to obtain the material properties and check its suitability to be used as active material in space actuators. Details of the tests and results of the characterization test campaign, focused in the material unique properties for their use in actuators, will be presented in this work. Some application examples of space mechanisms and actuators, currently under development, will be summarized as part of this work, demonstrating the technology suitability for the development of space actuators.

  2. Effects of magnetic field on the shape memory behavior of single and polycrystalline magnetic shape memory alloys

    Science.gov (United States)

    Turabi, Ali Sadi

    Shape memory alloys and polymers have been extensively researched recently because of their unique ability to recover large deformations. Shape memory polymers (SMPs) are able to recover large deformations compared to shape memory alloys (SMAs), although SMAs have higher strength and are able to generate more stress during recovery. This project focuses on procedure for fabrication and Finite Element Modeling (FEM) of a shape memory composite actuator. First, SMP was characterized to reveal its mechanical properties. Specifically, glass transition temperature, the effects of temperature and strain rate on compressive response and recovery properties of shape memory polymer were studied. Then, shape memory properties of a NiTi wire, including transformation temperatures and stress generation, were investigated. SMC actuator was fabricated by using epoxy based SMP and NiTi SMA wire. Experimental tests confirmed the reversible behavior of fabricated shape memory composites. (Abstract shortened by ProQuest.).

  3. Fastening apparatus having shape memory alloy actuator

    Science.gov (United States)

    Mckinnis, Darin N. (Inventor)

    1992-01-01

    A releasable fastening apparatus is presented. The device includes a connecting member and a housing. The housing supports a gripping mechanism that is adapted to engage the connecting member. A triggering member is movable within the housing between a first position in which it constrains the gripping mechanism in locked engagement with the connecting member, and a second position in which the gripping mechanism is disengaged from the connecting member. A shaped memory alloy actuator is employed for translating the triggering member from its first to its second position. The actuator is designed to expand longitudinally when transitioned from a martensitic to an austenitic state.

  4. Vacuum Plasma Spray Formed High Transition Temperature Shape Memory Alloys Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Smart materials control of aero-surfaces based on shape memory alloys (SMA) is seeing increased use for improving of future subsonic fixed wing aircraft aero-surface...

  5. NICKEL-BASE ALLOY

    Science.gov (United States)

    Inouye, H.; Manly, W.D.; Roche, T.K.

    1960-01-19

    A nickel-base alloy was developed which is particularly useful for the containment of molten fluoride salts in reactors. The alloy is resistant to both salt corrosion and oxidation and may be used at temperatures as high as 1800 deg F. Basically, the alloy consists of 15 to 22 wt.% molybdenum, a small amount of carbon, and 6 to 8 wt.% chromium, the balance being nickel. Up to 4 wt.% of tungsten, tantalum, vanadium, or niobium may be added to strengthen the alloy.

  6. Design of shape memory alloy (SMA) actuators

    CERN Document Server

    Rao, Ashwin; Reddy, J N

    2015-01-01

    This short monograph presents an analysis and design methodology for shape memory alloy (SMA) components such as wires, beams, and springs for different applications. The solid-solid, diffusionless phase transformations in thermally responsive SMA allows them to demonstrate unique characteristics like superelasticity and shape memory effects. The combined sensing and actuating capabilities of such materials allows them to provide a system level response by combining multiple functions in a single material system. In SMA, the combined mechanical and thermal loading effects influence the functionality of such materials. The aim of this book is to make the analysis of these materials accessible to designers by developing a "strength of materials" approach to the analysis and design of such SMA components inspired from their various applications with a review of various factors influencing the design process for such materials.

  7. Constitutive Models for Shape Memory Alloy Polycrystals

    Science.gov (United States)

    Comstock, R. J., Jr.; Somerday, M.; Wert, J. A.

    1996-01-01

    Shape memory alloys (SMA) exhibiting the superelastic or one-way effects can produce large recoverable strains upon application of a stress. In single crystals this stress and resulting strain are very orientation dependent. We show experimental stress/strain curves for a Ni-Al single crystal for various loading orientations. Also shown are model predictions; the open and closed circles indicate recoverable strains obtained at various stages in the transformation process. Because of the strong orientation dependence of shape memory properties, crystallographic texture can be expected to play an important role in the mechanical behavior of polycrystalline SMA. It is desirable to formulate a constitutive model to better understand and exploit the unique properties of SMA.

  8. Shape-memory alloy micro-actuator

    Science.gov (United States)

    Busch, John D. (Inventor); Johnson, Alfred D. (Inventor)

    1991-01-01

    A method of producing an integral piece of thermo-sensitive material, which is responsive to a shift in temperature from below to above a phase transformation temperature range to alter the material's condition to a shape-memory condition and move from one position to another. The method is characterized by depositing a thin film of shape-memory material, such as Nickel titanium (Ni-Ti) onto a substrate by vacuum deposition process such that the alloy exhibits an amorphous non-crystalline structure. The coated substrate is then annealed in a vacuum or in the presence of an inert atmosphere at a selected temperature, time and cool down rate to produce an ordered, partially disordered or fully disordered BCC structure such that the alloy undergoes thermoelastic, martinsetic phase transformation in response to alteration in temperature to pass from a martinsetic phase when at a temperature below a phase transformation range and capable of a high level of recoverable strain to a parent austenitic phase in a memory shape when at a temperature above the phase transformation range. Also disclosed are actuator devices employing shape-memory material actuators that deform from a set shape toward an original shape when subjected to a critical temperature level after having been initially deformed from the original shape into the set shape while at a lower temperature. The actuators are mechanically coupled to one or more movable elements such that the temperature-induce deformation of the actuators exerts a force or generates a motion of the mechanical element(s).

  9. Spooled packaging of shape memory alloy actuators

    Science.gov (United States)

    Redmond, John A.

    A vast cross-section of transportation, manufacturing, consumer product, and medical technologies rely heavily on actuation. Accordingly, progress in these industries is often strongly coupled to the advancement of actuation technologies. As the field of actuation continues to evolve, smart materials show significant promise for satisfying the growing needs of industry. In particular, shape memory alloy (SMA) wire actuators present an opportunity for low-cost, high performance actuation, but until now, they have been limited or restricted from use in many otherwise suitable applications by the difficulty in packaging the SMA wires within tight or unusually shaped form constraints. To address this packaging problem, SMA wires can be spool-packaged by wrapping around mandrels to make the actuator more compact or by redirecting around multiple mandrels to customize SMA wire pathways to unusual form factors. The goal of this dissertation is to develop the scientific knowledge base for spooled packaging of low-cost SMA wire actuators that enables high, predictable performance within compact, customizable form factors. In developing the scientific knowledge base, this dissertation defines a systematic general representation of single and multiple mandrel spool-packaged SMA actuators and provides tools for their analysis, understanding, and synthesis. A quasi-static analytical model distills the underlying mechanics down to the three effects of friction, bending, and binding, which enables prediction of the behavior of generic spool-packaged SMA actuators with specifiable geometric, loading, frictional, and SMA material parameters. An extensive experimental and simulation-based parameter study establishes the necessary understanding of how primary design tradeoffs between performance, packaging, and cost are governed by the underlying mechanics of spooled actuators. A design methodology outlines a systematic approach to synthesizing high performance SMA wire actuators

  10. Nondestructive Evaluation of Ni-Ti Shape Memory Alloy

    Science.gov (United States)

    Meir, S.; Gordon, S.; Karsh, M.; Wiezman, A.; Ayers, R.; Olson, D. L.

    2011-06-01

    The nondestructive evaluation of nickel titanium (Ni-Ti) alloys for applications such as heat treatment for biomaterials applications (dental) and welding was investigated. Ni-Ti alloys and its ternary alloys are valued for mechanical properties in addition to the shape memory effect. Two analytical approaches were perused in this work. Assessment of the microstructure of the alloy that determines the martensitic start temperature (Ms) of Ni-Ti alloy as a function of heat treatment, and secondly, an attempt to evaluate a Friction Stir Welding, which involves thermo-mechanical processing of the alloy.

  11. Effects of Annealing on the Martensitic Transformation of Ni-Based Ferromagnetic Shape Memory Heusler Alloys and Nanoparticles

    Directory of Open Access Journals (Sweden)

    Tina Fichtner

    2015-03-01

    Full Text Available We report on the effects of annealing on the martensitic phase transformation in the Ni-based Heusler system: Mn50Ni40Sn10 and Mn50Ni41Sn9 powder and Co50Ni21Ga32 nanoparticles. For the powdered Mn50Ni40Sn10 and Mn50Ni41Sn9 alloys, structural and magnetic measurements reveal that post-annealing decreases the martensitic transformation temperatures and increases the transition hysteresis. This might be associated with a release of stress in the Mn50Ni40Sn10 and Mn50Ni41Sn9 alloys during the annealing process. However, in the case of Co50Ni21Ga32 nanoparticles, a reverse phenomenon is observed. X-ray diffraction analysis results reveal that the as-prepared Co50Ni21Ga32 nanoparticles do not show a martensitic phase at room temperature. Post-annealing followed by ice quenching, however, is found to trigger the formation of the martensitic phase. The presence of the martensitic transition is attributed to annealing-induced particle growth and the stress introduced during quenching.

  12. Precipitation-Strengthened, High-Temperature, High-Force Shape Memory Alloys

    Science.gov (United States)

    Noebe, Ronald D.; Draper, Susan L.; Nathal, Michael V.; Crombie, Edwin A.

    2008-01-01

    Shape memory alloys (SMAs) are an enabling component in the development of compact, lightweight, durable, high-force actuation systems particularly for use where hydraulics or electrical motors are not practical. However, commercial shape memory alloys based on NiTi are only suitable for applications near room temperature, due to their relatively low transformation temperatures, while many potential applications require higher temperature capability. Consequently, a family of (Ni,Pt)(sub 1-x)Ti(sub x) shape memory alloys with Ti concentrations ranging from about 15 to 25 at.% have been developed for applications in which there are requirements for SMA actuators to exert high forces at operating temperatures higher than those of conventional binary NiTi SMAs. These alloys can be heat treated in the range of 500 C to produce a series of fine precipitate phases that increase the strength of alloy while maintaining a high transformation temperature, even in Ti-lean compositions.

  13. Evaluation of shape memory effect and damping characteristics of Cu–Al–Be–Mn shape memory alloys

    Directory of Open Access Journals (Sweden)

    A.G. Shivasiddaramaiah

    2016-09-01

    Full Text Available Among different shape memory alloys, copper (Cu based alloys were the most favourable alloys, because of their attaining price and good characteristic properties. In this present work different weight compositions of Cu–Al–Be–Mn shape memory alloys are considered and are in the range of 10–14 wt% of aluminium (Al, 0.4–0.5 wt% of beryllium (Be and 0.3–0.4 wt% of manganese (Mn and these alloys were synthesized by ingot metallurgy, which exhibits β-phase at higher temperatures, also demonstrates a shape memory effect (SME after quenching to room temperature. The Be, Mn and Al content was varied in different sets to study the shape memory effect and damping behaviour of the alloys by using differential scanning calorimetry and dynamic mechanical analyzer respectively. These alloys exhibit higher damping or internal friction in the martensitic condition and internal friction or damping peak in the transition zone.

  14. Nonlinear dynamics of a pseudoelastic shape memory alloy system - theory and experiment

    DEFF Research Database (Denmark)

    Enemark, Søren; A Savi, M.; Santos, Ilmar

    2014-01-01

    In this work, a helical spring made from a pseudoelastic shape memory alloy was embedded in a dynamic system also composed of a mass, a linear spring and an excitation system. The mechanical behaviour of shape memory alloys is highly complex, involving hysteresis, which leads to damping...... capabilities and varying stiffness. Besides, these properties depend on the temperature and pretension conditions. Because of these capabilities, shape memory alloys are interesting in relation to engineering design of dynamic systems. A theoretical model based on a modification of the 1D Brinson model...... and forced vibrations of the system setup under different temperature conditions. The experiments give a thorough insight into dynamic systems involving pseudoelastic shape memory alloys. Comparison between experimental results and the proposed model shows that the model is able to explain and predict...

  15. Numerical Analysis of Thermo-Mechanical Coupling in Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    S. Hashemi

    2016-01-01

    Full Text Available The phase transformation phenomenon due to the crystallographic change of shape memory alloys subjected to mechanical or thermal loading is very complicated. Regarding the thermo-mechanical coupling effects in shape memory alloys, in case of high  loading rates, heat generation/absorption during the forward/reverse transformation, will lead in temperature-dependent variation and consequently affects its mechanical behavior. In this paper, a numerical algorithm based on the finite element method is proposed to investigate complex mechanical, thermal, and coupled behavior of shape memory alloys, including both exclusive behaviours of these alloys, that are superelasticity and shape memory effect. Several key examples are simulated and discussed to assess the efficiency and accuracy of proposed algorithm.

  16. TUNGSTEN BASE ALLOYS

    Science.gov (United States)

    Schell, D.H.; Sheinberg, H.

    1959-12-15

    A high-density quaternary tungsten-base alloy having high mechanical strength and good machinability composed of about 2 wt.% Ni, 3 wt.% Cu, 5 wt.% Pb, and 90wt.% W is described. This alloy can be formed by the powder metallurgy technique of hot pressing in a graphite die without causing a reaction between charge and the die and without formation of a carbide case on the final compact, thereby enabling re-use of the graphite die. The alloy is formable at hot- pressing temperatures of from about 1200 to about 1350 deg C. In addition, there is little component shrinkage, thereby eliminating the necessity of subsequent extensive surface machining.

  17. An overview of constitutive models for shape memory alloys

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available The remarkable properties of shape memory alloys have facilitated their applications in many areas of technology. The purpose of this paper is to present an overview of thermomechanical behavior of these alloys, discussing the main constitutive models for their mathematical description. Metallurgical features and engineering applications are addressed as an introduction. Afterwards, five phenomenological theories are presented. In general, these models capture the general thermomechanical behavior of shape memory alloys, characterized by pseudoelasticity, shape memory effect, phase transformation phenomenon due to temperature variation, and internal subloops due to incomplete phase transformations.

  18. Transformation Volume Effects on Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Anna Kosogor

    2013-07-01

    Full Text Available It is generally accepted that the martensitic transformations (MTs in the shape memory alloys (SMAs are mainly characterized by the shear deformation of the crystal lattice that arises in the course of MT, while a comparatively small volume change during MT is considered as the secondary effect, which can be disregarded when the basic characteristics of MTs and functional properties of SMAs are analyzed. This point of view is a subject to change nowadays due to the new experimental and theoretical findings. The present article elucidates (i the newly observed physical phenomena in different SMAs in their relation to the volume effect of MT; (ii the theoretical analysis of the aforementioned volume-related phenomena.

  19. Rotor Embedded with Shape Memory Alloy Wires

    Directory of Open Access Journals (Sweden)

    K. Gupta

    2000-01-01

    Full Text Available In the present analysis, the fundamental natural frequency of a Jeffcott and a two-mass rotor with fibre reinforced composite shaft embedded with shape memory alloy (SMA wires is evaluated by Rayleigh's procedure. The flexibility of rotor supports is taken into account. The effect of three factors, either singly or in combination with each other, on rotor critical speed is studied. The three factors are: (i increase in Young's modulus of SMA (NITINOL wires when activated, (ii tension in wires because of phase recovery stresses, and (iii variation of support stiffness by three times because of activation of SMA in rotor supports. It is shown by numerical examples that substantial variation in rotor critical speeds can be achieved by a combination of these factors which can be effectively used to avoid resonance during rotor coast up/down.

  20. Shape Memory Alloy Actuator Design: CASMART Collaborative Best Practices

    Science.gov (United States)

    Benafan, Othmane; Brown, Jeff; Calkins, F. Tad; Kumar, Parikshith; Stebner, Aaron; Turner, Travis; Vaidyanathan, Raj; Webster, John; Young, Marcus L.

    2011-01-01

    Upon examination of shape memory alloy (SMA) actuation designs, there are many considerations and methodologies that are common to them all. A goal of CASMART's design working group is to compile the collective experiences of CASMART's member organizations into a single medium that engineers can then use to make the best decisions regarding SMA system design. In this paper, a review of recent work toward this goal is presented, spanning a wide range of design aspects including evaluation, properties, testing, modeling, alloy selection, fabrication, actuator processing, design optimization, controls, and system integration. We have documented each aspect, based on our collective experiences, so that the design engineer may access the tools and information needed to successfully design and develop SMA systems. Through comparison of several case studies, it is shown that there is not an obvious single, linear route a designer can adopt to navigate the path of concept to product. SMA engineering aspects will have different priorities and emphasis for different applications.

  1. Switchable Shape Memory Alloys (SMA) Thermal Materials Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Shape memory alloys applies to a group of materials that demonstrate the ability to return to some previously defined shape when subjected to the appropriate thermal...

  2. Nonhysteretic superelasticity of shape memory alloys at the nanoscale.

    Science.gov (United States)

    Zhang, Zhen; Ding, Xiangdong; Sun, Jun; Suzuki, Tetsuro; Lookman, Turab; Otsuka, Kazuhiro; Ren, Xiaobing

    2013-10-04

    We perform molecular dynamics simulations to show that shape memory alloy nanoparticles below the critical size not only demonstrate superelasticity but also exhibit features such as absence of hysteresis, continuous nonlinear elastic distortion, and high blocking force. Atomic level investigations show that this nonhysteretic superelasticity results from a continuous transformation from the parent phase to martensite under external stress. This aspect of shape memory alloys is attributed to a surface effect; i.e., the surface locally retards the formation of martensite and then induces a critical-end-point-like behavior when the system is below the critical size. Our work potentially broadens the application of shape memory alloys to the nanoscale. It also suggests a method to achieve nonhysteretic superelasticity in conventional bulk shape memory alloys.

  3. Thermo-Mechanical Methodology for Stabilizing Shape Memory Alloy Response

    Science.gov (United States)

    Padula, Santo

    2013-01-01

    This innovation is capable of significantly reducing the amount of time required to stabilize the strain-temperature response of a shape memory alloy (SMA). Unlike traditional stabilization processes that take days to weeks to achieve stabilized response, this innovation accomplishes stabilization in a matter of minutes, thus making it highly useful for the successful and practical implementation of SMA-based technologies in real-world applications. The innovation can also be applied to complex geometry components, not just simple geometries like wires or rods.

  4. Damping capacity in shape memory alloy honeycomb structures

    Science.gov (United States)

    Boucher, M.-A.; Smith, C. W.; Scarpa, F.; Miller, W.; Hassan, M. R.

    2010-04-01

    SMA honeycombs have been recently developed by several Authors [1, 2] as innovative cellular structures with selfhealing capability following mechanical indentation, unusual deformation (negative Poisson's ratio [3]), and possible enhanced damping capacity due to the natural vibration dissipation characteristics of SMAs under pseudoelastic and superelastic regime. In this work we describe the nonlinear damping effects of novel shape memory alloy honeycomb assemblies subjected to combine mechanical sinusoidal and thermal loading. The SMA honeycomb structures made with Ni48Ti46Cu6 are designed with single and two-phase polymeric components (epoxy), to enhance the damping characteristics of the base SMA for broadband frequency vibration.

  5. Nonlinear angle control of a sectioned airfoil by using shape memory alloys

    Directory of Open Access Journals (Sweden)

    Abreu G.

    2014-01-01

    Full Text Available The present work illustrates an application of shape memory alloys and nonlinear controller applied to the active angular control of a sectioned airfoil. The main objective of the proposed control system is to modify the shape of the profile based on a reference angle. The change of the sectioned airfoil angle is resultant by the effect of shape memory of the alloy due to heating of the wire caused by an electric current that changes its temperature by Joule effect. Considering the presence of plant’s nonlinear effects, especially in the mathematical model of the alloy, this work proposes the application of an on-off control system.

  6. Application of Ni-Ti base shape memory and super-elastic alloys; Ni-Ti kikeijo kioku oyobi chodansei gokin no jitsuyoka jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. [Furukawa Electric Co. Ltd., Yokahama (Japan). Yakahama R and D Laboratories

    1998-12-20

    The thermal hysteresis Hs of Ni-Ti binary alloy was between 20K and 40K. Those values had no problem when the alloy was used as a one-way element, but were too large for the use of the alloy as a reversible two-way actuator. Hs decreased to 10 - 15K by copper addition, and shape memory effect due to R (Rhombohedral) phase transformation was found later which decreased Hs by a large margin. Hs became as small as about 2K with the repetition life of more than 1 million times, and Hs became 100K by utilizing micro-dispersion of niobium. Applications of Ni-Ti binary alloy, Ni-Ti-Cu alloy, R phase alloy, and Ni-Ti-Nb alloy were discussed. Superelasticity was put to practical use in such a surprising field as the core grid for the brassiere, and used also for medical corsets. The field of spectacles rim is a treasure-house for the application of superelasticity. Applications also to antennas for portable telephones and orthodontic wire are successful. 30 refs., 21 figs., 1 tab.

  7. Two- way Shape Memory Effect in a Ti-Ni-Nb Shape Memory Alloy with Wide Hysteresis

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A two-way shape memory effect (TWSME) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM) observations. Based on the analysis of the microstructure after training, the mechanism of TWSME in the Ti46.3Ni44.7Nb9 alloy has been discussed.

  8. Modeling of shape memory alloys and application to porous materials

    Science.gov (United States)

    Panico, Michele

    In the last two decades the number of innovative applications for advanced materials has been rapidly increasing. Shape memory alloys (SMAs) are an exciting class of these materials which exhibit large reversible stresses and strains due to a thermoelastic phase transformation. SMAs have been employed in the biomedical field for producing cardiovascular stents, shape memory foams have been successfully tested as bone implant material, and SMAs are being used as deployable switches in aerospace applications. The behavior of shape memory alloys is intrinsically complex due to the coupling of phase transformation with thermomechanical loading, so it is critical for constitutive models to correctly simulate their response over a wide range of stress and temperature. In the first part of this dissertation, we propose a macroscopic phenomenological model for SMAs that is based on the classical framework of thermodynamics of irreversible processes and accounts for the effect of multiaxial stress states and non-proportional loading histories. The model is able to account for the evolution of both self-accommodated and oriented martensite. Moreover, reorientation of the product phase according to loading direction is specifically accounted for. Computational tests demonstrate the ability of the model to simulate the main aspects of the shape memory response in a one-dimensional setting and some of the features that have been experimentally found in the case of multi-axial non-proportional loading histories. In the second part of this dissertation, this constitutive model has been used to study the mesoscopic behavior of porous shape memory alloys with particular attention to the mechanical response under cyclic loading conditions. In order to perform numerical simulations, the model was implemented into the commercial finite element code ABAQUS. Due to stress concentrations in a porous microstructure, the constitutive law was enhanced to account for the development of

  9. Synthesis and evaluation of ageing effect on Cu–Al–Be–Mn quaternary Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    A.G. Shivasiddaramiah

    2016-09-01

    Full Text Available Copper based shape memory alloy exhibits high transformation temperature and ability to differ the achieved properties through alloying additions. A quaternary Cu–Al–Be–Mn shape memory alloys of 0.2–0.4 wt% of manganese, 0.4–0.5 wt% of Beryllium and 10–14 wt% of aluminium with remaining copper, showing β-phase at higher temperature and show shape memory effect when quenching to lower temperatures, SMA's were prepared by induction melting. The objective is to study the effect of thermal ageing at different temperatures Af (above austenitic phase finish temperature and at different time on shape memory effect and transformation temperatures. The aged specimens or SMA's were studied by DSC, OM and hardness measurements. The results from this study help to find the applications in different thermal conditions.

  10. Development of Ultra-high Mechanical Damping Structures Based on Nano-scale Properties of Shape Memory Alloys

    Science.gov (United States)

    2011-07-27

    Alloys Jose San Juan Universidad del Pais Vasco Department of Physics of Condensed Matter Facultd de Ciencia y Tecnologia Bilbao...Facultd de Ciencia y Tecnologia Bilbao, Spain 48080 8. PERFORMING ORGANIZATION REPORT NUMBER N/A 9. SPONSORING/MONITORING AGENCY NAME(S

  11. Shape memory effect in Fe-Mn-Ni-Si-C alloys with low Mn contents

    Energy Technology Data Exchange (ETDEWEB)

    Min, X.H., E-mail: MIN.Xiaohua@nims.go.jp [National Institute for Materials Science, Tsukuba 305-0047 (Japan); Sawaguchi, T.; Ogawa, K. [National Institute for Materials Science, Tsukuba 305-0047 (Japan); Maruyama, T. [Awaji Materia Co., Ltd. 2-3-13, Kanda ogawamachi, Chiyoda, Tokyo 101-0052 (Japan); Yin, F.X. [National Institute for Materials Science, Tsukuba 305-0047 (Japan); Tsuzaki, K. [National Institute for Materials Science, Tsukuba 305-0047 (Japan); Graduate School of Pure and Applied Sciences, University of Tsukuba, Ibaraki 305-0047 (Japan)

    2011-06-15

    Highlights: {yields} A class of new Fe-Mn-Ni-Si-C shape memory alloys with low Mn contents has been designed. {yields} A Mn content for the onset of the {alpha}' martensite is less than 13 mass%, and the {epsilon} martensite still exists in the alloy with a 9 mass% Mn. {yields} The shape recovery strain decreases considerably when the Mn content is reduced from 13 to 11 mass%. {yields} The sudden decrease in the shape recovery strain is mainly caused by the formation of {alpha}' martensite. - Abstract: An attempt was made to develop a new Fe-Mn-Si-based shape memory alloy from a Fe-17Mn-6Si-0.3C (mass%) shape memory alloy, which was previously reported to show a superior shape memory effect without any costly training treatment, by lowering its Mn content. The shape memory effect and the phase transformation behavior were investigated for the as-solution treated Fe-(17-2x)Mn-6Si-0.3C-xNi (x = 0, 1, 2, 3, 4) polycrystalline alloys. The shape recovery strain exceeded 2% in the alloys with x = 0-2, which is sufficient for an industrially applicable shape memory effect; however, it suddenly decreased in the alloys between x = 2 and 3 although the significant shape recovery strain still exceeded 1%. In the alloys with x = 3 and 4, X-ray diffraction analysis and transmission electron microscope observation revealed the existence of {alpha}' martensite, which forms at the intersection of the {epsilon} martensite plates and suppresses the crystallographic reversibility of the {gamma} austenite to {epsilon} martensitic transformation.

  12. Effect of Cu Content on Atomic Positions of Ti50Ni50−xCux Shape Memory Alloys Based on Density Functional Theory Calculations

    Directory of Open Access Journals (Sweden)

    Liangliang Gou

    2015-11-01

    Full Text Available The study of crystal structures in shape memory alloys is of fundamental importance for understanding the shape memory effect. In order to investigate the mechanism of how Cu content affects martensite crystal structures of TiNiCu alloys, the present research examines the atomic displacement of Ti50Ni50−xCux (x = 0, 5, 12.5, 15, 18.75, 20, 25 shape memory alloys using density functional theory (DFT. By the introduction of Cu atoms into TiNi martensite crystal to replace Ni, the displacements of Ti and Ni/Cu atoms along the x-axis are obvious, but they are minimal along the y- and z-axes. It is found that along the x-axis, the two Ti atoms in the unit cell move in opposite directions, and the same occurred with the two Ni/Cu atoms. With increasing Cu content, the distance between the two Ni/Cu atoms increases while the Ti atoms draw closer along the x-axis, leading to a rotation of the (100 plane, which is responsible for the decrease in the monoclinic angle. It is also found that the displacements of both Ti atoms and Ni/Cu atoms along the x-axis are progressive, which results in a gradual change of monoclinic angle and a transition to B19 martensite crystal structure.

  13. Modeling the Cyclic Behavior of Shape Memory Alloys

    Science.gov (United States)

    Waimann, Johanna; Junker, Philipp; Hackl, Klaus

    2017-06-01

    The phenomenon of functional fatigue occurs during cyclic loading of pseudoelastic shape memory alloys. We model this effect by considering an irreversible martensitic volume fraction in addition to the reversible amounts of austenite and martensite based on variational principles. The inclusion of irreversible martensitic volume fractions coincides with experimental observations and enables the model to be easily calibrated without any fitting functions. In our previous studies, we modeled the polycrystalline material structure by static discretization of a relatively large number of randomly chosen grain orientations, which required much numerical effort. In contrast, we now apply a dynamic representation of the orientation distribution function to the modeling of functional fatigue which has proven to be beneficial regarding the numerical performance. To this end, we take into account an averaged grain orientation parameterized by three Euler angles that serve as additional internal variables. This results in an extremely reduced numerical effort. The model derivation is given along with the numerical implementation and computer experiments on the cyclic behavior of shape memory alloys.

  14. Fatigue Crack Growth Fundamentals in Shape Memory Alloys

    Science.gov (United States)

    Wu, Y.; Ojha, A.; Patriarca, L.; Sehitoglu, H.

    2015-03-01

    In this study, based on a regression of the crack tip displacements, the stress intensity range in fatigue is quantitatively determined for the shape memory alloy Ni2FeGa. The results are compared to the calculated stress intensity ranges with a micro-mechanical analysis accounting for the transformation-induced tractions. The effective stress intensity ranges obtained with both methods are in close agreement. Also, the fatigue crack closure levels were measured as 30 % of the maximum load using virtual extensometers along the crack flanks. This result is also in close agreement with the regression and micro-mechanical modeling findings. The current work pointed to the importance of elastic moduli changes and the residual transformation strains playing a role in the fatigue crack growth behavior. Additional simulations are conducted for two other important shape memory alloys, NiTi and CuZnAl, where the reductions in stress intensity range were found to be lower than Ni2FeGa.

  15. Recentering Shape Memory Alloy Passive Damper for Structural Vibration Control

    Directory of Open Access Journals (Sweden)

    Hui Qian

    2013-01-01

    Full Text Available This paper presents a preliminary study on the evaluation of an innovative energy dissipation system with shape memory alloys (SMAs for structural seismic protection. A recentering shape memory alloy damper (RSMAD, in which superelastic nitinol wires are utilized as energy dissipation components, is proposed. Improved constitutive equations based on Graesser and Cozzarelli model are proposed for superelastic nitinol wires used in the damper. Cyclic tensile-compressive tests on the damper with various prestrain under different loading frequencies and displacement amplitudes were conducted. The results show that the hysteretic behaviors of the damper can be modified to best fit the needs for passive structural control applications by adjusting the pretension of the nitinol wires, and the damper performance is not sensitive to frequencies greater than 0.5 Hz. To assess the effectiveness of the dampers for structural seismic protection, nonlinear time history analysis on a ten-story steel frame with and without the dampers subjected to representative earthquake ground motions was performed. The simulation results indicate that superelastic SMA dampers are effective in mitigating the structural response of building structures subjected to strong earthquakes.

  16. A Review of TiNiPdCu Alloy System for High Temperature Shape Memory Applications

    Science.gov (United States)

    Khan, M. Imran; Kim, Hee Young; Miyazaki, Shuichi

    2015-06-01

    High temperature shape memory alloys (HTSMAs) are important smart materials and possess a significant potential to improve many engineering systems. Many TiNi-based high temperature ternary alloy systems have been reported in literature including TiNiPd, TiNiPt, TiNiZr, TiNiAu, TiNiHf, etc. Some quaternary additions of certain elements in the above systems have been successful to further improve many important shape memory and mechanical properties. The success criteria for an HTSMA become strict in terms of its cyclic stability, maximum recoverable strain, creep resistance, and corrosion resistance at high temperatures. TiNiPdCu alloy system has been recently proposed as a promising HTSMA. Unique nanoscaled precipitates formed in TiNiPdCu-based HTSMAs are found to be stable at temperatures above 773 K, while keeping the benefits of ease of fabrication. It is expected that this alloy system possesses significant potential especially for the high temperature shape memory applications. Till now many research reports have been published on this alloy system. In the present work, a comprehensive review of the TiNiPdCu system is presented in terms of thermomechanical behavior, nanoscale precipitation mechanism, microstructural features, high temperature shape memory and mechanical properties, and the important parameters to control the high temperature performance of these alloys.

  17. Deformation Heterogeneity and Texture Evolution of NiTiFe Shape Memory Alloy Under Uniaxial Compression Based on Crystal Plasticity Finite Element Method

    Science.gov (United States)

    Liang, Yulong; Jiang, Shuyong; Zhang, Yanqiu; Zhao, Yanan; Sun, Dong; Zhao, Chengzhi

    2017-04-01

    Crystal plastic finite element method (CPFEM) is used to simulate microstructural evolution, texture evolution and macroscopic stress-strain response of polycrystalline NiTiFe shape memory alloy (SMA) with B2 austenite phase during compression deformation. A novel two-dimensional polycrystalline finite element model based on electron back-scattered diffraction (EBSD) experiment data is developed to represent virtual grain structures of polycrystalline NiTiFe SMA. In the present study, CPFEM plays a significant role in predicting texture evolution and macroscopic stress-strain response of NiTiFe SMA during compression deformation. The simulated results are in good agreement with the experimental ones. It can be concluded that intragranular and intergranular strain heterogeneities are of great importance in guaranteeing plastic deformation compatibility of NiTiFe SMA. CPFEM is able to capture the evolution of grain boundaries with various misorientation angles for NiTiFe SMA subjected to the various compression deformation degrees. During uniaxial compression of NiTiFe SMA, the microstructure evolves into high-energy substructure and consequently the well-defined subgrains are formed. Furthermore, the grain boundaries and the subgrain boundaries are approximately aligned with the direction in which metal flows.

  18. The industrial applications of shape memory alloys in North America

    Energy Technology Data Exchange (ETDEWEB)

    Mc Schetky D, L. [Memry Corp., Brookfield, CT (United States)

    2000-07-01

    Literature in the recent past on shape memory effect alloys dwelt principally on the physical metallurgy, crystallography and kinetics of the shape memory phenomenon. By contrast, we now have books and conference proceedings devoted to the engineering aspects of SMAs, their technology and application. The dominant role SMAs now play in the field of medical and orthodontic devices is well documented and will be reviewed by others in this conference. In this paper we will discuss the commercial applications for shape memory alloy devices in the North American market; applications which are in many cases also produced in European countries and Japan. The early success of shape memory alloy couplings for joining tubing and pipe in the late 1960's was not followed by other large volume applications until the advent of shape memory eyeglass frames, brassiere underwires and cellular phone antennas. Many other applications have now evolved into mature markets and these will be reviewed. In addition to the many commercial applications cited, there are a number of other fields in which shape memory alloys are destined to play a major role; these include smart materials and adaptive structures, MEMS devices, infrastructure systems and electrical power generation and distribution. These applications are being developed with private and government funding and will also be briefly discussed. (orig.)

  19. Twice reverse shape memory effect in CuZnAl shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    李周; 汪明朴; 徐根应; 郭明星

    2004-01-01

    The variations of the shape memory effects in the Cu-13Zn-15Al(mole fraction, %) alloy upon successive heating (the rate of heating is 5 ℃/min) have been studied by means of p-T curve , shape memory effect measurement, optical metallographical observation and X-ray diffraction. The first abnormal reverse shape memory effect occurs when the tested alloy is heated to the temperature below 320 ℃; when it is heated to the temperature between 320 ℃ and 450 ℃, the forward shape memory effect occurs; in the two stages, the shape of the sample remains the same as that in the furnace when it is taken out from the furnace and air-cooled; when the tested alloy is heated to the temperature above 450 ℃, the shape of the sample remains unchanged during heating, but the second reverse shape memory effect occurs after it is air-quenched.

  20. Functional Characterization of a Novel Shape Memory Alloy

    Science.gov (United States)

    Collado, M.; Cabás, R.; San Juan, J.; López-Ferreño, I.

    2014-07-01

    A novel shape memory alloy (SMA) has been developed as an alternative to currently available alloys. This alloy, commercially known by its proprietary brand SMARQ, shows a higher working range of temperatures with respect to the SMA materials used until now in actuators, limited to environment temperatures below 90 °C. SMARQ is a high temperature SMA (HTSMA) based on a fully European material technology and production processes, which allows the manufacture of high quality products, with tuneable transformation temperatures up to 200 °C. Both, material and production processes have been evaluated for its use in space applications. A full characterization test campaign has been completed in order to obtain the material properties and check its suitability to be used as active material in space actuators. In order to perform the functional characterization of the material, it has been considered as the key element of a basic SMA actuator, consisting in the SMA wire and the mechanical and electrical interfaces. The functional tests presented in this work have been focused on the actuator behavior when heated by means of an electrical current. Alloy composition has been adjusted in order to match a transition temperature (As) of +145 °C, which satisfies the application requirements of operating temperatures in the range of -70 and +125 °C. Details of the tests and results of the characterization test campaign, focused in the material unique properties for their use in actuators, will be presented in this work. Some application examples in the field of space mechanisms and actuators, currently under development, will be summarized as part of this work, demonstrating the technology suitability as active material for space actuators.

  1. Thermomechanical Methodology for Stabilizing Shape Memory Alloy (SMA) Response

    Science.gov (United States)

    Padula, Santo A., II (Inventor)

    2016-01-01

    Methods and apparatuses for stabilizing the strain-temperature response for a shape memory alloy are provided. To perform stabilization of a second sample of the shape memory alloy, a first sample of the shape memory alloy is selected for isobaric treatment and the second sample is selected for isothermal treatment. When applying the isobaric treatment to the first sample, a constant stress is applied to the first sample. Temperature is also cycled from a minimum temperature to a maximum temperature until a strain on the first sample stabilizes. Once the strain on the first sample stabilizes, the isothermal treatment is performed on the second sample. During isothermal treatment, different levels of stress on the second sample are applied until a strain on the second sample matches the stabilized strain on the first sample.

  2. Structural Acoustic Response of Shape Memory Alloy Hybrid Composite Panels

    Science.gov (United States)

    Turner, Travis L.

    1996-01-01

    A method has been developed to predict the structural acoustic response of shape memory alloy hybrid composite panels subjected to acoustic excitation. The panel is modeled by a finite element analysis and the radiated field is predicted using Rayleigh's integral. Transmission loss predictions for the case of an aluminum panel excited by a harmonic acoustic pressure are shown to compare very well with a classical analysis. Predictions of the normal velocity response and transmitted acoustic pressure for a clamped aluminum panel show excellent agreement with experimental measurements. Predicted transmission loss performance for a composite panel with and without shape memory alloy reinforcement are also presented. The preliminary results demonstrate that the transmission loss can be significantly increased with shape memory alloy reinforcement.

  3. First Principles Modelling of Shape Memory Alloys Molecular Dynamics Simulations

    CERN Document Server

    Kastner, Oliver

    2012-01-01

    Materials sciences relate the macroscopic properties of materials to their microscopic structure and postulate the need for holistic multiscale research. The investigation of shape memory alloys is a prime example in this regard. This particular class of materials exhibits strong coupling of temperature, strain and stress, determined by solid state phase transformations of their metallic lattices. The present book presents a collection of simulation studies of this behaviour. Employing conceptually simple but comprehensive models, the fundamental material properties of shape memory alloys are qualitatively explained from first principles. Using contemporary methods of molecular dynamics simulation experiments, it is shown how microscale dynamics may produce characteristic macroscopic material properties. The work is rooted in the materials sciences of shape memory alloys and  covers  thermodynamical, micro-mechanical  and crystallographical aspects. It addresses scientists in these research fields and thei...

  4. Periodic Cellular Structure Technology for Shape Memory Alloys

    Science.gov (United States)

    Chen, Edward Y.

    2015-01-01

    Shape memory alloys are being considered for a wide variety of adaptive components for engine and airframe applications because they can undergo large amounts of strain and then revert to their original shape upon heating or unloading. Transition45 Technologies, Inc., has developed an innovative periodic cellular structure (PCS) technology for shape memory alloys that enables fabrication of complex bulk configurations, such as lattice block structures. These innovative structures are manufactured using an advanced reactive metal casting technology that offers a relatively low cost and established approach for constructing near-net shape aerospace components. Transition45 is continuing to characterize these structures to determine how best to design a PCS to better exploit the use of shape memory alloys in aerospace applications.

  5. A Constitutive Description for Shape Memory Alloys with the Growth of Martensite Band

    Directory of Open Access Journals (Sweden)

    Weiguo Li

    2014-01-01

    Full Text Available Based on the experimental results and the finite element analysis, a constitutive model is proposed for two phase shape memory alloys by introducing a compensative volumetric strain into a constrained relationship between the two phases, accounting for the reduced constraint due to the growth of martensite band. The pseudoelasticity of NiTi shape memory alloy micro-tube, subjected to pure tension, is analyzed and compared with the experimental results. It can be seen that the pseudoelastic behavior, especially the phenomena of a stress drop during tension processes, can be well described with the proposed model. The proposed model separates the complicated constitutive behavior of a shape memory alloy (SMA into simple responses arising respectively from its two phases, taking into account laminar microstructure, the thickness of martensite phase and the interaction between the two phases, and provides an easy but comprehensive method for the description of the constitutive behavior of SMAs under complex thermomechanical loading.

  6. A Constitutive Description for Shape Memory Alloys with the Growth of Martensite Band.

    Science.gov (United States)

    Li, Weiguo; Shen, Xueliang; Peng, Xianghe

    2014-01-20

    Based on the experimental results and the finite element analysis, a constitutive model is proposed for two phase shape memory alloys by introducing a compensative volumetric strain into a constrained relationship between the two phases, accounting for the reduced constraint due to the growth of martensite band. The pseudoelasticity of NiTi shape memory alloy micro-tube, subjected to pure tension, is analyzed and compared with the experimental results. It can be seen that the pseudoelastic behavior, especially the phenomena of a stress drop during tension processes, can be well described with the proposed model. The proposed model separates the complicated constitutive behavior of a shape memory alloy (SMA) into simple responses arising respectively from its two phases, taking into account laminar microstructure, the thickness of martensite phase and the interaction between the two phases, and provides an easy but comprehensive method for the description of the constitutive behavior of SMAs under complex thermomechanical loading.

  7. Microstructural investigation on marforming and conventional cold deformation in Ni-Ti-Fe-based shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Basu, Ritwik; Szpunar, Jerzy; Eskandari, Mostafa; Mohtadi-Bonab, M.A. [Univ. Saskatchewan, Dept. of Mechanical Engineering, Saskatoon (Canada)

    2015-08-15

    A hot-rolled Ni-Ti-Fe alloy was subjected to 50% cold rolling by laboratory rolling mill and was subsequently annealed at 800 C for 1.5 h. This sample was then deformed through another 10% reduction in thickness by two different routes (i) conventional cold rolling and (ii) marforming (rolling in liquid nitrogen) followed by annealing under identical conditions. The grain refinement during normal cold rolling was attributed to relatively large presence of dislocations in the ND // left angle 110 right angle grains in the starting microstructure. The regions of higher dislocation densities became gradually textured to ND // left angle 111 right angle orientation, with cold rolling. Marforming (deformation in liquid nitrogen following phase transformation) on the other hand led to more significant grain refinement and also change in the bulk texture. The objective of this study was to compare the grain refinement and microstructural modification produced through marforming with that obtained in conventional cold deformation.

  8. A rotating arm using shape-memory alloy

    Science.gov (United States)

    Jenkins, Phillip P.; Landis, Geoffrey A.

    1995-01-01

    NASA's Mars Pathfinder mission, to be launched in 1996, reflects a new philosophy of exploiting new technologies to reduce mission cost and accelerate the pace of space exploration. One of the experiments on board Pathfinder will demonstrate the first use in space of a multi-cycle, electrically-activated, shape-memory alloy (SMA) actuator. SMA's are metal alloys which, when heated, undergo a crystalline phase change. This change in phase alters the alloy lattice-constant, resulting in a change of dimension. Upon cooling, the alloy returns to its original lattice formation. Wire drawn from an SMA contracts in length when heated. The reversible change in length is 3 percent to 5 percent. The wire used in this actuator is a nickel-titanium alloy known as nitinol.

  9. Nonlinear angle control of a sectioned airfoil by using shape memory alloys

    OpenAIRE

    Abreu G.; Maestá M.; Faria C.; Lopes V.

    2014-01-01

    The present work illustrates an application of shape memory alloys and nonlinear controller applied to the active angular control of a sectioned airfoil. The main objective of the proposed control system is to modify the shape of the profile based on a reference angle. The change of the sectioned airfoil angle is resultant by the effect of shape memory of the alloy due to heating of the wire caused by an electric current that changes its temperature by Joule effect. Considering the presence o...

  10. Modelling, characterisation and uncertainties of stabilised pseudoelastic shape memory alloy helical springs

    DEFF Research Database (Denmark)

    Enemark, Søren; Santos, Ilmar; Savi, M. A.

    2016-01-01

    The thermo-mechanical behaviour of pseudoelastic shape memory alloy helical springs is of concern discussing stabilised and cyclic responses. Constitutive description of the shape memory alloy is based on the framework developed by Lagoudas and co-workers incorporating two modifications related...... resulting in 1.3% residual standard deviation relative to the full range force. Compared to the validation data set, the errors are below 10% relative to the full range of the complex modulus. Uncertainty analysis of the model parameters using a Markov chain Monte Carlo technique shows low to high parameter...

  11. A Model to Describe the Magnetomechanical Behavior of Martensite in Magnetic Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Zaoyang Guo

    2014-01-01

    Full Text Available A model to describe the constitutive behavior of magnetic shape memory alloy composed with pure martensite is proposed based on the analysis of variants reorientation. A hyperbolic tangent expression is given to describe the variants transition during magnetic and mechanical loading process. The main features of magnetic shape memory alloy, such as pseudoelastic and partially pseudoelastic behavior as well as minor hysteretic loops, can be successfully replicated with the proposed model. A good agreement is achieved between calculated results and experimental data for NiMnGa single crystal.

  12. Vibration mitigation by the reversible fcc/hcp martensitic transformation during cyclic tension-compression loading of an Fe-Mn-Si-based shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Sawaguchi, Takahiro [National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)]. E-mail: sawaguchi.takahiro@nims.go.jp; Sahu, Puspendu [Materials Science and Technology Division, National Metallurgical Laboratory, Jamshedpur 831 007 (India); Kikuchi, Takehiko [National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Ogawa, Kazuyuki [National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Kajiwara, Setsuo [National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Kushibe, Atsumichi [Takenaka Corporation, 1-5-1, Otsuka, Inzai, Chiba 270-1395 (Japan); Higashino, Masahiko [Takenaka Corporation, 1-5-1, Otsuka, Inzai, Chiba 270-1395 (Japan); Ogawa, Takatoshi [Takenaka Corporation, 1-5-1, Otsuka, Inzai, Chiba 270-1395 (Japan)

    2006-06-15

    The present work concerns the damping behavior of an Fe-28Mn-6Si-5Cr-0.5NbC (mass%) shape memory alloy determined by low cycle fatigue tests, and the corresponding deformation mechanism under cyclic tension-compression loading. The specific damping capacity increases with increasing strain amplitude and reaches saturation at {approx}80%, above the strain amplitude of 0.4%. Quantitative X-ray diffraction analyses and microstructural observations using atomic force microscopy revealed that a significant amount of the tensile stress-induced {epsilon} martensite is reversely transformed into the austenite by subsequent compression; in other words, the stress-induced 'reverse' martensitic transformation takes place in the alloy.

  13. Using Shape Memory Alloys: A Dynamic Data Driven Approach

    KAUST Repository

    Douglas, Craig C.

    2013-06-01

    Shape Memory Alloys (SMAs) are capable of changing their crystallographic structure due to changes of either stress or temperature. SMAs are used in a number of aerospace devices and are required in some devices in exotic environments. We are developing dynamic data driven application system (DDDAS) tools to monitor and change SMAs in real time for delivering payloads by aerospace vehicles. We must be able to turn on and off the sensors and heating units, change the stress on the SMA, monitor on-line data streams, change scales based on incoming data, and control what type of data is generated. The application must have the capability to be run and steered remotely as an unmanned feedback control loop.

  14. Application Of Shape Memory Alloy In Harvesto-Absorber System

    Directory of Open Access Journals (Sweden)

    Kęcik Krzysztof

    2015-09-01

    Full Text Available This paper presents a conception of the harvester-absorber system consisting of two parts. The first is the pendulum attached to the main system (oscillator, which is suspended on the linear damper and the nonlinear spring made of shape memory alloy. The spring is modelled as a polynomial function based on Landau–Ginzburg theory of phase transitions (similar as ferroelectric and ferromagnets. The obtained results show, that SMA element can increase harvesting energy level, while the absorber effect can be impaired (but not loss. Additionally, introducing SMA element causes changes in dynamics, introduces a new unstable solutions and bifurcations. The analysis was done by classical integration and continuation solution methods.

  15. Biocorrosion investigation of two shape memory nickel based alloys: Ni-Mn-Ga and thin film NiTi.

    Science.gov (United States)

    Stepan, L L; Levi, D S; Gans, E; Mohanchandra, K P; Ujihara, M; Carman, G P

    2007-09-01

    Thin film nitinol and single crystal Ni-Mn-Ga represent two new shape memory materials with potential to be used as percutaneously placed implant devices. However, the biocompatibility of these materials has not been adequately assessed. Immersion tests were conducted on both thin film nitinol and single crystal Ni-Mn-Ga in Hank's balanced salt solution at 37 degrees C and pH 7.4. After 12 h, large pits were found on the Ni-Mn-Ga samples while thin film nitinol displayed no signs of corrosion. Further electrochemical tests on thin film nitinol samples revealed breakdown potentials superior to a mechanically polished nitinol disc. These results suggest that passivation or electropolishing of thin film nitinol maybe unnecessary to promote corrosion resistance.

  16. Applications of shape memory alloys for neurology and neuromuscular rehabilitation.

    Science.gov (United States)

    Pittaccio, Simone; Garavaglia, Lorenzo; Ceriotti, Carlo; Passaretti, Francesca

    2015-05-27

    Shape memory alloys (SMAs) are a very promising class of metallic materials that display interesting nonlinear properties, such as pseudoelasticity (PE), shape memory effect (SME) and damping capacity, due to high mechanical hysteresis and internal friction. Our group has applied SMA in the field of neuromuscular rehabilitation, designing some new devices based on the mentioned SMA properties: in particular, a new type of orthosis for spastic limb repositioning, which allows residual voluntary movement of the impaired limb and has no predetermined final target position, but follows and supports muscular elongation in a dynamic and compliant way. Considering patients in the sub-acute phase after a neurological lesion, and possibly bedridden, the paper presents a mobiliser for the ankle joint, which is designed exploiting the SME to provide passive exercise to the paretic lower limb. Two different SMA-based applications in the field of neuroscience are then presented, a guide and a limb mobiliser specially designed to be compatible with diagnostic instrumentations that impose rigid constraints in terms of electromagnetic compatibility and noise distortion. Finally, the paper discusses possible uses of these materials in the treatment of movement disorders, such as dystonia or hyperkinesia, where their dynamic characteristics can be advantageous.

  17. Applications of Shape Memory Alloys for Neurology and Neuromuscular Rehabilitation

    Directory of Open Access Journals (Sweden)

    Simone Pittaccio

    2015-05-01

    Full Text Available Shape memory alloys (SMAs are a very promising class of metallic materials that display interesting nonlinear properties, such as pseudoelasticity (PE, shape memory effect (SME and damping capacity, due to high mechanical hysteresis and internal friction. Our group has applied SMA in the field of neuromuscular rehabilitation, designing some new devices based on the mentioned SMA properties: in particular, a new type of orthosis for spastic limb repositioning, which allows residual voluntary movement of the impaired limb and has no predetermined final target position, but follows and supports muscular elongation in a dynamic and compliant way. Considering patients in the sub-acute phase after a neurological lesion, and possibly bedridden, the paper presents a mobiliser for the ankle joint, which is designed exploiting the SME to provide passive exercise to the paretic lower limb. Two different SMA-based applications in the field of neuroscience are then presented, a guide and a limb mobiliser specially designed to be compatible with diagnostic instrumentations that impose rigid constraints in terms of electromagnetic compatibility and noise distortion. Finally, the paper discusses possible uses of these materials in the treatment of movement disorders, such as dystonia or hyperkinesia, where their dynamic characteristics can be advantageous.

  18. Thermally driven phase transformation on shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mielke, A. [Weierstrass-Institut fuer Angewandte Analysis und Stochastik (WIAS) im Forschungsverbund Berlin e.V. (Germany)]|[Humboldt-Universitaet, Berlin (Germany). Inst. fuer Mathematik; Petrov, A. [Weierstrass-Institut fuer Angewandte Analysis und Stochastik (WIAS) im Forschungsverbund Berlin e.V. (Germany)

    2007-07-01

    This paper analyzes a model for phase transformation in shape-memory alloys induced by temperature changes and by mechanical loading. We assume that the temperature is prescribed and formulate the problem within the framework of the energetic theory of rate-independent processes. Existence and uniqueness results are proved. (orig.)

  19. Switchable Shape Memory Alloys (SMA) Thermal Materials Project

    Science.gov (United States)

    Falker, John; Zeitlin, Nancy; Williams, Martha; Fesmire, James

    2014-01-01

    Develop 2-way switchable thermal systems for use in systems that function in cold to hot temperature ranges using different alloy designs for SMA system concepts. In this project, KSC will specifically address designs of two proof of concept SMA systems with transition temperatures in the 65-95 C range and investigate cycle fatigue and "memory loss" due to thermal cycling.

  20. The Origin of Vibration Redemption Effect for Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Daniel Amariei

    2007-10-01

    Full Text Available Shape memory alloys (SMA components can affect through two mechanisms the vibrations of structures. The stresses from a SMA element that realize phase transformations, as a result of vibrations, have an effect on the frequency-amplitude characteristics. In addition, a dissipation of energy due to hysteresis in a SMA element can reduce the natural frequency and affect forced vibrations.

  1. Shape memory alloys: a state of art review

    Science.gov (United States)

    Naresh, C.; Bose, P. S. C.; Rao, C. S. P.

    2016-09-01

    Shape memory alloys (SMAs) are the special materials that have the ability to return to a predetermined shape when heated. When this alloy is in below transformation temperature it undergoes low yield strength and will deform easily into any new shape which it will retain, if this alloy is heated above its transformation temperature it changes its crystal lattice structure which returns to its real shape. SMAs are remarkably different from other materials are primarily due to shape memory effect (SME) and pseudoelasticity which are related with the specific way the phase transformation occurs, biocompatibility, high specific strength, high corrosion resistance, high wear resistance and high anti-fatigue property. SMA are used in many applications such as aerospace, medical, automobile, tubes, controllers for hot water valves in showers, petroleum industry, vibration dampers, ball bearings, sensors, actuators, miniature grippers, micro valves, pumps, landing gears, eye glass frames, Material for helicopter blades, sprinklers in fine alarm systems packaging devices for electronic materials, dental materials, etc. This paper focuses on introducing shape memory alloy and their applications in past, present and in future, also revealed the concept and mechanism of shape memory materials for a particular requirement. Properties of SMAs, behaviour and characteristics of SMA, summary of recent advances and new application opportunities are also discussed.

  2. An investigation of shape memory alloys, as actuating elements, in aerospace morphing applications

    DEFF Research Database (Denmark)

    Karagiannis, Dimitrios; Stamatelos, Dimtrios; Kappatos, Vassilios;

    2016-01-01

    Two innovative actuating concepts for aerospace morphing applications, based on Shape Memory Alloys (SMAs), are proposed. The first concept investigates a composite plate incorporating embedded SMA wires. A Nonlinear Auto Regressive with eXogenous excitation (NARX) model is proposed for controlling...

  3. Microstructures and properties of welded joint of TiNi shape memory alloy and stainless steel

    Institute of Scientific and Technical Information of China (English)

    邱小明; 孙大谦; 李明高; 刘卫红

    2004-01-01

    The fracture characteristics of the joint were analyzed by means of scanning electron microscope(SEM).Microstructures of the joint were examined by means of optical microscope, SEM and an image analyzer. The results show that the tensile strength of the inhomogeneous joint of TiNi shape memory alloy and stainless steel is lower than that of the homogeneous joint and a plastic field appears in the heat affected zone on the side of TiNi shape memory alloy. Because TiNi shape memory alloy and stainless steel melted, a brittle as-cast structure was formed in the weld. The tensile strength and the shape memory effect of the inhomogeneous joint are strongly influenced by the changes of composition and structure of the joint. Measures should be taken to reduce the base metal melting and prevent the weld metal from the invasion by O for improving the properties of the TiNi shape memory alloy and stainless steel inhomogeneous joint.

  4. Multiscale Characterization of Nickel Titanium Shape Memory Alloys

    Science.gov (United States)

    Gall, Keith

    Shape memory alloys were characterized by a variety of methods to investigate the relationship between microstructural phase transformation, macroscale deformation due to mechanical loading, material geometry, and initial material state. The major portion of the work is application of digital image correlation at several length scales to SMAs under mechanical loading. In addition, the connection between electrical resistance, stress, and strain was studied in NiTi wires. Finally, a new processing method was investigated to develop porous NiTi samples, which can be examined under DIC in future work. The phase transformation temperatures of a Nickel-Titanium based shape memory alloy (SMA) were initially evaluated under stress-free conditions by the differential scanning calorimetric (DSC) technique. Results show that the phase transformation temperature is significantly higher for transition from de-twinned martensite to austenite than from twinned martensite or R phase to austenite. To further examine transformation temperatures as a function of initial state a tensile test apparatus with in-situ electrical resistance (ER) measurements was used to evaluate the transformation properties of SMAs at a variety of stress levels and initial compositions. The results show that stress has a significant influence on the transformation of detwinned martensite, but a small influence on R phase and twinned martensite transformations. Electrical resistance changes linearly with strain during the transformations from both kinds of martensite to austenite. The linearity between ER and strain during the transformation from de-twinned martensite to austenite is not affected by the stress, facilitating application to control algorithms. A revised phase diagram is drawn to express these results. To better understand the nature of the local and global strain fields that accompany phase transformation in shape memory alloys (SMAs), here we use high resolution imaging together with image

  5. Functional and structural fatigue of titanium tantalum high temperature shape memory alloys (HT SMAs)

    Energy Technology Data Exchange (ETDEWEB)

    Niendorf, T., E-mail: Thomas.Niendorf@iwt.tu-freiberg.de [Institute of Materials Engineering, Technische Universität Bergakademie Freiberg, 09599 Freiberg (Germany); Krooß, P. [Lehrstuhl für Werkstoffkunde (Materials Science), University of Paderborn, 33098 Paderborn (Germany); Batyrsina, E. [Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, 30823 Garbsen (Germany); Paulsen, A.; Motemani, Y.; Ludwig, A.; Buenconsejo, P.; Frenzel, J.; Eggeler, G. [Institut für Werkstoffe, Ruhr-Universität Bochum, 44801 Bochum (Germany); Maier, H.J. [Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, 30823 Garbsen (Germany)

    2015-01-03

    Due to their high work output and good mechanical properties, actuators made from shape memory alloys (SMAs) are used in numerous applications. Unfortunately, SMAs such as nickel–titanium (Ni–Ti) can only be employed at temperatures up to about 100 °C. Lately, high-temperature shape memory alloys (HT SMAs) have been introduced to overcome this limitation. Ternary systems based on Ni–Ti have been intensively characterized and alloys are available that can operate at elevated temperatures. However, these alloys either contain substantial amounts of expensive noble elements like platinum and palladium, or the materials are brittle. The titanium–tantalum (Ti–Ta) system has been developed to overcome these issues. Binary Ti–Ta provides relatively high M{sub S} temperature combined with excellent workability, but it suffers from fast cyclic degradation. By alloying with third elements this drawback can be overcome: The ternary Ti–Ta–Al alloy shows overall promising properties as will be shown in the present work. In-situ thermo-mechanical cycling experiments were conducted and allowed for evaluation of the factors affecting the functional and structural fatigue of this alloy. Functional fatigue is dominated by ω-phase evolution, while structural fatigue is triggered by an interplay of ω-phase induced embrittlement and deformation constraints imposed by unsuitable texture. In addition, a concept for fatigue life extension proposed very recently for binary Ti–Ta, is demonstrated to be also applicable for the ternary Ti–Ta–Al.

  6. Shape memory alloys: metallurgy, biocompatibility, and biomechanics for neurosurgical applications.

    Science.gov (United States)

    Hoh, Daniel J; Hoh, Brian L; Amar, Arun P; Wang, Michael Y

    2009-05-01

    SHAPE MEMORY ALLOYS possess distinct dynamic properties with particular applications in neurosurgery. Because of their unique physical characteristics, these materials are finding increasing application where resiliency, conformation, and actuation are needed. Nitinol, the most frequently manufactured shape memory alloy, responds to thermal and mechanical stimuli with remarkable mechanical properties such as shape memory effect, super-elasticity, and high damping capacity. Nitinol has found particular use in the biomedical community because of its excellent fatigue resistance and biocompatibility, with special interest in neurosurgical applications. The properties of nitinol and its diffusionless phase transformations contribute to these unique mechanical capabilities. The features of nitinol, particularly its shape memory effect, super-elasticity, damping capacity, as well as its biocompatibility and biomechanics are discussed herein. Current and future applications of nitinol and other shape memory alloys in endovascular, spinal, and minimally invasive neurosurgery are introduced. An understanding of the metallurgic properties of nitinol provides a foundation for further exploration of its use in neurosurgical implant design.

  7. Thermal Arrest Memory Effect in Ni-Mn-Ga Alloys

    Directory of Open Access Journals (Sweden)

    A. Rudajevova

    2008-01-01

    Full Text Available Dilatation characteristics were measured to investigate the thermal arrest memory effect in Ni53.6Mn27.1Ga19.3 and Ni54.2Mn29.4Ga16.4 alloys. Interruption of the martensite-austenite phase transformation is connected with the reduction of the sample length after thermal cycle. If a total phase transformation took place in the complete thermal cycle following the interruption, then the sample length would return to its original length. Analysis of these results has shown that the thermal arrest memory effect is a consequence of a stress-focusing effect and shape memory effect. The stress-focusing effect occurs when the phase transformation propagates radially in a cylindrical sample from the surface, inward to the center. Evolution and release of the thermoelastic deformations in both alloys during heating and cooling are analyzed.

  8. Understanding the shape-memory alloys used in orthodontics.

    Science.gov (United States)

    Fernandes, Daniel J; Peres, Rafael V; Mendes, Alvaro M; Elias, Carlos N

    2011-01-01

    Nickel-titanium (NiTi) shape-memory alloys (SMAs) have been used in the manufacture of orthodontic wires due to their shape memory properties, super-elasticity, high ductility, and resistance to corrosion. SMAs have greater strength and lower modulus of elasticity when compared with stainless steel alloys. The pseudoelastic behavior of NiTi wires means that on unloading they return to their original shape by delivering light continuous forces over a wider range of deformation which is claimed to allow dental displacements. The aim of this paper is to discuss the physical, metallurgical, and mechanical properties of NiTi used in Orthodontics in order to analyze the shape memory properties, super-elasticity, and thermomechanical characteristics of SMA.

  9. Understanding the Shape-Memory Alloys Used in Orthodontics

    Science.gov (United States)

    Fernandes, Daniel J.; Peres, Rafael V.; Mendes, Alvaro M.; Elias, Carlos N.

    2011-01-01

    Nickel-titanium (NiTi) shape-memory alloys (SMAs) have been used in the manufacture of orthodontic wires due to their shape memory properties, super-elasticity, high ductility, and resistance to corrosion. SMAs have greater strength and lower modulus of elasticity when compared with stainless steel alloys. The pseudoelastic behavior of NiTi wires means that on unloading they return to their original shape by delivering light continuous forces over a wider range of deformation which is claimed to allow dental displacements. The aim of this paper is to discuss the physical, metallurgical, and mechanical properties of NiTi used in Orthodontics in order to analyze the shape memory properties, super-elasticity, and thermomechanical characteristics of SMA. PMID:21991455

  10. Fabrication and modeling of shape memory alloy springs

    Science.gov (United States)

    Heidari, B.; Kadkhodaei, M.; Barati, M.; Karimzadeh, F.

    2016-12-01

    In this paper, shape memory alloy (SMA) helical springs are produced by shape setting two sets of NiTi (Ti-55.87 at% Ni) wires, one of which showing shape memory effect and another one showing pseudoelasticity at the ambient temperature. Different pitches as well as annealing temperatures are tried to investigate the effect of such parameters on the thermomechanical characteristics of the fabricated springs. Phase transformation temperatures of the products are measured by differential scanning calorimetry and are compared with those of the original wires. Compression tests are also carried out, and stiffness of each spring is determined. The desired pitches are so that a group of springs experiences phase transition during loading while the other does not. The former shows a varying stiffness upon the application of compression, but the latter acts as passive springs with a predetermined stiffness. Based on the von-Mises effective stress and strain, an enhanced one-dimensional constitutive model is further proposed to describe the shear stress-strain response within the coils of an SMA spring. The theoretically predicted force-displacement responses of the produced springs are shown to be in a reasonable agreement with the experimental results. Finally, effects of variations in geometric parameters on the axial force-displacement response of an SMA spring are investigated.

  11. Modeling of thermomechanical response of porous shape memory alloys

    Science.gov (United States)

    Lagoudas, Dimitris C.; Entchev, Pavlin B.; Vandygriff, Eric L.; Qidwai, Muhammad A.; DeGiorgi, Virginia G.

    2000-06-01

    Shape memory alloys (SMAs) have emerged as a class of materials with unique thermal and mechanical properties that have found numerous applications in various engineering areas. While the shape memory and pseudoelasticity effects have been extensively studied, only a few studies have been done on the high capacity of energy dissipation of SMAs. Because of this property, SMAs hold the promise of making high-efficiency damping devices that are superior to those made of conventional materials. In addition to the energy absorption capability of the dense SMA material, porous SMAs offer the possibility of higher specific damping capacity under dynamic loading conditions, du to scattering of waves. Porous SMAs also offer the possibility of impedance matching by grading the porosity at connecting joints with other structural materials. As a first step, the focus of this work, is on establishing the static properties of porous SMA material. To accomplish this, a micromechanics-based analysis of the overall behavior of porous SMA is carried out. The porous SMA is modeled as a composite with SMA matrix, which is modeled using an incremental formulation, and pores as inhomogeneities of zero stiffness. The macroscopic constitutive behavior of the effective medium is established using the incremental More-Tanaka averaging method for a random distribution of pores, and a FEM analysis of a unit cell for a periodic arrangement of pores. Results form both analyses are compared under various loading conditions.

  12. The Investigation of a Shape Memory Alloy Micro-Damper for MEMS Applications

    Directory of Open Access Journals (Sweden)

    Chongdu Cho

    2007-09-01

    Full Text Available Some shape memory alloys like NiTi show noticeable high damping property inpseudoelastic range. Due to its unique characteristics, a NiTi alloy is commonly used forpassive damping applications, in which the energy may be dissipated by the conversion frommechanical to thermal energy. This study presents a shape memory alloy based micro-damper, which exploits the pseudoelasticity of NiTi wires for energy dissipation. Themechanical model and functional principle of the micro-damper are explained in detail.Moreover, the mechanical behavior of NiTi wires subjected to various temperatures, strainrates and strain amplitudes is observed. Resulting from those experimental results, thedamping properties of the micro-damper involving secant stiffness, energy dissipation andloss factor are analyzed. The result indicates the proposed NiTi based micro-damper exhibitsgood energy dissipation ability, compared with conventional materials damper.

  13. Electrochemical behavior of YAG laser-welded NiTi shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    YAN Xiao-jun; YANG Da-zhi; LIU Xiao-peng

    2006-01-01

    Electrochemical behaviors of laser-welded Ti-50.6%Ni(mole fraction) shape memory alloy and the base metal in 0.9% NaCl solution were investigated by electrochemical techniques as corrosion potential measurement, linear and potentiodynamic polarization. The results indicate that the laser-welded NiTi alloy is less susceptible to pitting and crevice corrosion than the base metal, which is demonstrated by the increase in polarization resistance(Rp) and pitting potential(ψpit) and decrease in corrosion current density(Jcorr) and mean difference between ψpit and ψprot values. It is confirmed by scanning electron microscope micrographs that pits could be observed on the surface of base metal but not on the surface of laser-welded alloy after potentiodynamic tests. An improvement of corrosion resistance of laser-welded NiTi alloy could be attributed to almost complete dissolution of inclusions upon laser welding.

  14. Damping of High-temperature Shape Memory Alloys

    Science.gov (United States)

    Duffy, Kirsten P.; Padula, Santo A., II; Scheiman, Daniel A.

    2008-01-01

    Researchers at NASA Glenn Research Center have been investigating high temperature shape memory alloys as potential damping materials for turbomachinery rotor blades. Analysis shows that a thin layer of SMA with a loss factor of 0.04 or more would be effective at reducing the resonant response of a titanium alloy beam. Two NiTiHf shape memory alloy compositions were tested to determine their loss factors at frequencies from 0.1 to 100 Hz, at temperatures from room temperature to 300 C, and at alternating strain levels of 34-35x10(exp -6). Elevated damping was demonstrated between the M(sub s) and M(sub f) phase transformation temperatures and between the A(sub s) and A(sub f) temperatures. The highest damping occurred at the lowest frequencies, with a loss factor of 0.2-0.26 at 0.1 Hz. However, the peak damping decreased with increasing frequency, and showed significant temperature hysteresis in heating and cooling. Keywords: High-temperature, shape memory alloy, damping, aircraft engine blades, NiTiHf

  15. Microstructural evolution in a Ti-Ta high-temperature shape memory alloy during creep

    Energy Technology Data Exchange (ETDEWEB)

    Rynko, Ramona; Marquardt, Axel; Pauksen, Alexander; Frenzel, Jan; Somsen, Christoph; Eggeler, Gunther [Bochum Univ. (Germany). Inst. for Materials

    2015-04-15

    Alloys based on the titanium-tantalum system are considered for application as high-temperature shape memory alloys due to their martensite start temperatures, which can surpass 200 C. In the present work we study the evolution of microstructure and the influence of creep on the phase transformation behavior of a Ti{sub 70}Ta{sub 30} (at.%) high-temperature shape memory alloy. Creep tests were performed in a temperature range from 470 to 530 C at stresses between 90 and 150 MPa. The activation energy for creep was found to be 307 kJ mol{sup -1} and the stress exponent n was determined as 3.7. Scanning and transmission electron microscopy investigations were carried out to characterize the microstructure before and after creep. It was found that the microstructural evolution during creep suppresses subsequent martensitic phase transformations.

  16. Multistage Development of Müller-Achenbach model for Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Simin A. Oshkovr

    2008-01-01

    Full Text Available This research focused on the conceptual development of constitutive Müller-Achenbach model and proceeds to construct a model based on phase transition under changing temperature and load for variants of martensite in shape memory alloy CuAlNi (Copper-aluminum-nickel. Problem statement: Motivation of this research is rare information of a variant of martensite phase (M++ and prediction of the shape recovery of shape memory alloy in this stage of transformation. Approach: The mathematical equations proposed a prediction of stability of Austenite phases and extend it to multistage martensitic phase transformation. These phase transformations occurred by loading on the material. Equations described free energy landscape in CuAlNi shape memory alloys at low (260K and high temperature (440K. The model evaluated the free energy due to the phase transformation between the austenite and multistage martensitic structures. Results: Results for M++ phase showed decrease in temperature from 440K to 260K presented decrease in stress approximately from 1 kN to 0.4kN and free energy from 5 kJ/kg to 0.1 kJ/kg. Equations have been solved and plotted by software programmed in MATLAB. Conclusions/Recommendations: The model which has derived focused on homogeneous shape memory alloys, but future performance requirements will most likely be met with heterogeneous materials. Therefore, simulation models for heterogeneous materials must be developed.

  17. Biomedical Applications of Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Lorenza Petrini

    2011-01-01

    behaviors, due to the peculiar crystallographic structure of the alloys, assure the recovery of the original shape even after large deformations and the maintenance of a constant applied force in correspondence of significant displacements. These properties, joined with good corrosion and bending resistance, biological and magnetic resonance compatibility, explain the large diffusion, in the last 20 years, of SMA in the production of biomedical devices, in particular for mini-invasive techniques. In this paper a detailed review of the main applications of NiTi alloys in dental, orthopedics, vascular, neurological, and surgical fields is presented. In particular for each device the main characteristics and the advantages of using SMA are discussed. Moreover, the paper underlines the opportunities and the room for new ideas able to enlarge the range of SMA applications. However, it is fundamental to remember that the complexity of the material and application requires a strict collaboration between clinicians, engineers, physicists and chemists for defining accurately the problem, finding the best solution in terms of device design and accordingly optimizing the NiTi alloy properties.

  18. STUDY ON SHAPE MEMORY ALLOYS CONSTITUTIVE MODEL BASED ON ABAQUS%基于ABAQUS的形状记忆合金本构研究

    Institute of Scientific and Technical Information of China (English)

    董金芝; 毛晨曦; 曹鹏

    2010-01-01

    利用ABAQUS的用户材料子程序VUMAT编制了的形状记忆合金(Shape memory alloys,SMA)超弹性本构模型,并将其本构模型嵌入到ABAQUS材料库中.基于ABAQUS程序以及上述形状记忆合金本构模型,本文计算分析了某含有SMA材料构件的12层剪力墙结构在地震荷载作用下的响应,验证了该子程序的正确性及准确性.

  19. A cycloidal wobble motor driven by shape memory alloy wires

    Science.gov (United States)

    Hwang, Donghyun; Higuchi, Toshiro

    2014-05-01

    A cycloidal wobble motor driven by shape memory alloy (SMA) wires is proposed. In realizing a motor driving mechanism well known as a type of reduction system, a cycloidal gear mechanism is utilized. It facilitates the achievement of bidirectional continuous rotation with high-torque capability, based on its high efficiency and high reduction ratio. The applied driving mechanism consists of a pin/roller based annular gear as a wobbler, a cycloidal disc as a rotor, and crankshafts to guide the eccentric wobbling motion. The wobbling motion of the annular gear is generated by sequential activation of radially phase-symmetrically placed SMA wires. Consequently the cycloidal disc is rotated by rolling contact based cycloidal gearing between the wobbler and the rotor. In designing the proposed motor, thermomechanical characterization of an SMA wire biased by extension springs is experimentally performed. Then, a simplified geometric model for the motor is devised to conduct theoretical assessment of design parametric effects on structural features and working performance. With consideration of the results from parametric analysis, a functional prototype three-phase motor is fabricated to carry out experimental verification of working performance. The observed experimental results including output torque, rotational speed, bidirectional positioning characteristic, etc obviously demonstrate the practical applicability and potentiality of the wobble motor.

  20. Investigations of a nanostructured FeMnSi shape memory alloy produced via severe plastic deformation

    Institute of Scientific and Technical Information of China (English)

    Gheorghe Gurau; Carmela Gurau; Vedamanickam Sampath; Leandru Gheorghe Bujoreanu

    2016-01-01

    Low-costiron-based shape memory alloys (SMAs) show great potential for engineering applications. The developments of new processing techniques have recently enabled the production of nanocrystalline materials with improved properties. These developments have opened avenues for newer applications for SMAs. The influence of severe plastic deformation induced by the high-speed high-pressure tor-sion (HSHPT) process on the microstructural evolution of an Fe–Mn–Si–Cr alloy was investigated. Transmission electron microscopic analysis of the alloy revealed the existence of nanoscale grains with an abundance of stacking faults. The high density of dislocations charac-teristic of severe plastic deformation was not observed in this alloy. X-ray diffraction studies revealed the presence ofε-martensite with an HCP crystal structure andγ-phase with an FCC structure.

  1. Investigations of a nanostructured FeMnSi shape memory alloy produced via severe plastic deformation

    Science.gov (United States)

    Gurau, Gheorghe; Gurau, Carmela; Sampath, Vedamanickam; Bujoreanu, Leandru Gheorghe

    2016-11-01

    Low-cost iron-based shape memory alloys (SMAs) show great potential for engineering applications. The developments of new processing techniques have recently enabled the production of nanocrystalline materials with improved properties. These developments have opened avenues for newer applications for SMAs. The influence of severe plastic deformation induced by the high-speed high-pressure torsion (HSHPT) process on the microstructural evolution of an Fe-Mn-Si-Cr alloy was investigated. Transmission electron microscopic analysis of the alloy revealed the existence of nanoscale grains with an abundance of stacking faults. The high density of dislocations characteristic of severe plastic deformation was not observed in this alloy. X-ray diffraction studies revealed the presence of ɛ-martensite with an HCP crystal structure and γ-phase with an FCC structure.

  2. Characterization of NiTi shape memory alloys using dual kriging interpolation

    Energy Technology Data Exchange (ETDEWEB)

    Trochu, F.; Sacepe, N.; Volkov, O.; Turenne, S. [Ecole Polytechnique, Montreal, PQ (Canada). Dept. of Mechanical Engineering

    1999-12-15

    A large number of industrial applications could benefit from the remarkable properties of shape memory alloys (SMA). The development of a general material law is the first important step before reliable design calculations of shape memory devices can be carried out. This paper presents a new phenomenological constitutive law based on dual kriging, which is a powerful mathematical tool used here as interpolation method to simulate the macroscopic mechanical behavior of shape memory alloys. From a set of experimental strain-temperature curves at constant loads, two deformation surfaces are constructed in the stress, strain and temperature space which describe the cooling and heating behaviors of the material for any stress. The response of a specimen subjected to complex thermomechanical loading can be calculated by dual kriging form a general 3-dimensional parametric solid constructed inside the hysteretic domain delimited by the main cooling and heating deformation surfaces. This approach presents the advantage of yielding immediately the explicit equation of any partial cycle inside the main hysteretic domain, thus yielding a general material law for shape memory alloys. Preliminary validation for a set of simple examples demonstrates the potential of this new model that includes in a single formulation superelasticity, rubber-like behavior and shape memory effect. (orig.)

  3. Design of shape memory alloy pipe couplers: modeling and experiments

    Science.gov (United States)

    Tabesh, Majid; Atli, Kadri C.; Rohmer, John; Franco, Brian E.; Karaman, Ibrahim; Boyd, James G.; Lagoudas, Dimitris C.

    2012-04-01

    Shape memory alloy (SMA) pipe couplers use the shape memory effect to apply a contact pressure onto the surface of the pipes to be coupled. In the current research, a SMA pipe coupler is designed, fabricated and tested. The thermally induced contact pressure depends on several factors such as the dimensions and properties of the coupler-pipe system. Two alloy systems are considered: commercially-available NiTiNb couplers and in-house developed NiTi couplers. The coupling pressure is measured using strain gages mounted on the internal surface of an elastic ring. An axisymmetric finite element model including SMA constitutive equations is also developed, and the finite element results are compared with the experimental results.

  4. Low Temperature Shape Memory Alloys for Adaptive, Autonomous Systems Project

    Science.gov (United States)

    Falker, John; Zeitlin, Nancy; Williams, Martha; Benafan, Othmane; Fesmire, James

    2015-01-01

    The objective of this joint activity between Kennedy Space Center (KSC) and Glenn Research Center (GRC) is to develop and evaluate the applicability of 2-way SMAs in proof-of-concept, low-temperature adaptive autonomous systems. As part of this low technology readiness (TRL) activity, we will develop and train low-temperature novel, 2-way shape memory alloys (SMAs) with actuation temperatures ranging from 0 C to 150 C. These experimental alloys will also be preliminary tested to evaluate their performance parameters and transformation (actuation) temperatures in low- temperature or cryogenic adaptive proof-of-concept systems. The challenge will be in the development, design, and training of the alloys for 2-way actuation at those temperatures.

  5. Implement of Shape Memory Alloy Actuators in a Robotic Hand

    OpenAIRE

    2006-01-01

    This paper was conceived to present the ideology of utilizing advanced actuators to design and develop innovative, lightweight, powerful, compact, and as much as possible dexterous robotic hands. The key to satisfying these objectives is the use of Shape Memory Alloys (SMAs) to power the joints of the robotic hand. The mechanical design of a dexterous robotic hand, which utilizes non-classical types of actuation and information obtained from the study of biological systems, is presented in th...

  6. Dynamic Simulation for Hysteresis in Shape Memory Alloy under Tension

    Institute of Scientific and Technical Information of China (English)

    WANG Ping; ZHAO Jian-Bo; TANG Shao-Qiang

    2008-01-01

    We demonstrate that the Suliciu model is capable to model the hysteresis phenomenon observed experimentally in NiTi shape memory alloy micro-tubes.This model allows a class of stationary phase interfaces.By a series of fully dynamic numerical simulations that mimic quasi-static loading and unloading,the nominal stress-strain curve exhibits a big hysteresis loop,which quantitatively agrees with the experimental results.

  7. Shape Control of Solar Collectors Using Shape Memory Alloy Actuators

    Science.gov (United States)

    Lobitz, D. W.; Grossman, J. W.; Allen, J. J.; Rice, T. M.; Liang, C.; Davidson, F. M.

    1996-01-01

    Solar collectors that are focused on a central receiver are designed with a mechanism for defocusing the collector or disabling it by turning it out of the path of the sun's rays. This is required to avoid damaging the receiver during periods of inoperability. In either of these two cases a fail-safe operation is very desirable where during power outages the collector passively goes to its defocused or deactivated state. This paper is principally concerned with focusing and defocusing the collector in a fail-safe manner using shape memory alloy actuators. Shape memory alloys are well suited to this application in that once calibrated the actuators can be operated in an on/off mode using a minimal amount of electric power. Also, in contrast to other smart materials that were investigated for this application, shape memory alloys are capable of providing enough stroke at the appropriate force levels to focus the collector. Design and analysis details presented, along with comparisons to test data taken from an actual prototype, demonstrate that the collector can be repeatedly focused and defocused within accuracies required by typical solar energy systems. In this paper the design, analysis and testing of a solar collector which is deformed into its desired shape by shape memory alloy actuators is presented. Computations indicate collector shapes much closer to spherical and with smaller focal lengths can be achieved by moving the actuators inward to a radius of approximately 6 inches. This would require actuators with considerably more stroke and some alternate SMA actuators are currently under consideration. Whatever SMA actuator is finally chosen for this application, repeatability and fatigue tests will be required to investigate the long term performance of the actuator.

  8. Interfacial Modulus Mapping during Structural Transformation in Shape Memory Alloys

    Science.gov (United States)

    Wan, Jianfeng; Cui, Shushan; Zhang, Jihua; Rong, Yonghua

    2017-10-01

    Through the modified phase-field model the local soft mode mechanism of nucleation during martensitic transformation was confirmed in shape memory alloys. It was discovered that the modulus loss (8 pct) depended on the martensitic nucleation exceeding the loss (1 pct) during the martensitic growth. The elastic modulus and the stress across the martensite/parent interface differed from those across the martensitic twin boundary. The modulus losses in systems with three variants, two variants, and one variant were compared.

  9. Miniature High Force, Long Stroke Linear Shape Memory Alloy Actuators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Shape Memory Alloys (SMAs) are metal alloys (Nickel-Titanium, for example) that change shape when heated. When drawn and processed in wire form, the shape change is...

  10. Miniature High Force, Long Stroke Linear Shape Memory Alloy Actuators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Shape Memory Alloys (SMAs) are metal alloys (of Nickel-Titanium, for example) that can change their shape when heated. When drawn and processed in wire form, the...

  11. A novel inertial energy harvester using magnetic shape memory alloy

    Science.gov (United States)

    Askari Farsangi, Mohammad Amin; Sayyaadi, Hassan; Zakerzadeh, Mohammad Reza

    2016-10-01

    This paper studies the output voltage from a novel inertial energy harvester using magnetic shape memory alloys (MSMAs). The MSMA elements are attached to the root of a cantilever beam by means of two steps. In order to get electrical voltage, two coils are wound around the MSMAs and a shock load is applied to a tip mass at the end of the beam to have vibration in it. The beam vibration causes strain in the MSMAs along their longitudinal directions and as a result the magnetic flux alters in the coils. The change of magnetic flux in the surrounding coil produces an AC voltage. In order to predict the output voltage, the nonlinear governing equations of beam motion based on Euler-Bernoulli model and von Kármán theory are derived. A thermodynamics-based constitutive model is used to predict the nonlinear strain and magnetization response of the MSMAs. Also, the induced voltage during martensite variant reorientation in MSMAs is investigated with the help of Faraday’s law of induction. Finally, the effect of different parameters including bias magnetic field, pre-strain and number of MSMA elements are investigated in details. The results show that this novel energy harvester has the capability of using as an alternative to the current piezoelectric and magnetostrictive ones for harvesting energy from ambient vibration.

  12. Electro-mechanical behavior of a shape memory alloy actuator

    Science.gov (United States)

    Pausley, Matthew E.; Furst, Stephen J.; Talla, Vamsi; Seelecke, Stefan

    2009-03-01

    This paper presents experimental study and numerical simulation of the electro-thermo-mechanical behavior of a commercially available Flexinol shape memory alloy (SMA) wire [1]. Recently, a novel driver device has been presented [2], which simultaneously controls electric power and measures resistance of an SMA wire actuator. This application of a single wire as both actuator and sensor will fully exploit the multifunctional nature of SMA materials and minimize system complexity by avoiding extra sensors. Though the subject is not new [3-6], comprehensive resistance data under controlled conditions for time-resolved and hysteresis-based experiments is not readily available from the literature. A simple experimental setup consisting of a Flexinol wire mounted in series with the tip of a compliant cantilever beam is used to systematically study the SMA behavior. A Labview-based data acquisition system measures actuator displacement and SMA wire stress and resistance and controls the power passed through the SMA actuator wire. The experimental setup is carefully insulated from ambient conditions, as the thermal response of a 50-micron diameter Flexinol wire is extremely sensitive to temperature fluctuation due to convective heat transfer. Actuator performance is reported for a range of actuation frequencies and input power levels. The effect of varying actuator pre-stress is reported as well. All of the experimental data is compared with simulated behavior that is derived from a numerical model for SMA material [7-10].

  13. Laser surface alloying fabricated porous coating on NiTi shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    ZHANG Song; ZHANG Chun-hua; MAN Hau-chung; LIU Chang-sheng

    2007-01-01

    Laser surface alloying technique was applied to fabricate a metallic porous coating on a solid NiTi shape memory alloy. By laser surface alloying a 40%TiH2-60%NiTi powder mixture on the surface of NiTi alloy using optimized laser process parameters, a porous but crack-free NiTi layer can be fabricated on the NiTi substrate. The porous coating is metallurgically bonded to the substrate NiTi alloy. The pores are uniformly distributed and are interconnected with each other in the coating. An average pore size of less than 10 μm is achieved. The Ni content of the porous layer is much less than that of the original NiTi surface. The existence of the porous coating on the NiTi alloy causes a 37% reduction of the tensile strength and 55% reduction of the strain as compared with the NiTi alloy. Possible biomedical or other applications for this porous surface with good mechanical strength provided by the substrate are prospective.

  14. Shape memory alloys applied to improve rotor-bearing system dynamics - an experimental investigation

    OpenAIRE

    2015-01-01

    tor-bearing systems have critical speeds and to pass through them is an ongoing challenge in the field of mechanical engineering. The incorporation of shape memory alloys in rotating systems has an increasing importance to improve system performance and to avoid potential damaging situations when passing through critical speeds. In this work, the feasibility of applying shape memory alloys to a rotating system is experimentally investigated. Shape memory alloys can change their stiffness with...

  15. Tribological characteristics of ceramic conversion treated NiTi shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Ju, X; Dong, H [Department of Metallurgy and Materials, School of Engineering, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2007-09-21

    NiTi shape memory alloys are very attractive for medical implants and devices (such as orthopaedic and orthodontic implants) and various actuators. However, wear is a major concern for such applications and a novel surface engineering process, ceramic conversion treatment, has recently been developed to address this problem. In this study, the tribological characteristics of ceramic conversion treated NiTi alloy have been systematically investigated under dry unidirectional wear, reciprocating-corrosion wear and fretting-corrosion wear condition. Based on the experimental results, the wear behaviour under different conditions is compared and wear mechanisms involved are discussed.

  16. Thermally activated retainer means utilizing shape memory alloy

    Science.gov (United States)

    Grimaldi, Margaret E. (Inventor); Hartz, Leslie S. (Inventor)

    1993-01-01

    A retainer member suitable for retaining a gap filler placed in gaps between adjacent tile members is presented. One edge of the retainer member may be attached to the gap filler and another edge may be provided with a plurality of tab members which in an intermediate position do not interfere with placement or removal of the gap filler between tile members. The retainer member may be fabricated from a shape memory alloy which when heated to a specified memory temperature will thermally activate the tab members to predetermined memory positions engaging the tile members to retain the gap filler in the gap. This invention has particular application to the thermal tiles on space vehicles such as the Space Shuttle Orbiter.

  17. Micro pulling down growth of very thin shape memory alloys single crystals

    Science.gov (United States)

    López-Ferreño, I.; Juan, J. San; Breczewski, T.; López, G. A.; Nó, M. L.

    Shape memory alloys (SMAs) have attracted much attention in the last decades due to their thermo-mechanical properties such as superelasticity and shape memory effect. Among the different families of SMAs, Cu-Al-Ni alloys exhibit these properties in a wide range of temperatures including the temperature range of 100-200∘C, where there is a technological demand of these functional materials, and exhibit excellent behavior at small scale making them more competitive for applications in Micro Electro-Mechanical Systems (MEMS). However, polycrystalline alloys of Cu-based SMAs are very brittle so that they show their best thermo-mechanical properties in single-crystal state. Nowadays, conventional Bridgman and Czochralski methods are being applied to elaborate single-crystal rods up to a minimum diameter of 1mm, but no works have been reported for smaller diameters. With the aim of synthesizing very thin single-crystals, the Micro-Pulling Down (μ-PD) technique has been applied, for which the capillarity and surface tension between crucible and the melt play a critical role. The μ-PD method has been successfully applied to elaborate several cylindrical shape thin single-crystals down to 200μm in diameter. Finally, the martensitic transformation, which is responsible for the shape memory properties of these alloys, has been characterized for different single-crystals. The experimental results evidence the good quality of the grown single-crystals.

  18. An extended thermo-mechanically coupled algorithm for simulation of superelasticity and shape memory effect in shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    S. HASHEMI; H. AHMADIAN; S. MOHAMMADI

    2015-01-01

    Thermo-mechanical coupling in shape memory alloys is a very complicated phenomenon. The heat generation/absorption during forward/reverse transformation can lead to temperature-dependent variation of its mechanical behavior in the forms of superelasticity and shape memory effect. However, unlike the usual assumption, slow loading rate cannot guarantee an isothermal process. A two-dimensional thermo-mechanically coupled algorithm is proposed based on the original model of Lagoudas to efficiently model both superelasticity and shape memory effects and the influence of various strain rates, aspect ratios and boundary conditions. To implement the coupled model into a finite element code, a numerical staggered algorithm is employed. A number of simulations are performed to verify the proposed approach with available experimental and numerical data and to assess its efficiency in solving complex SMA problems.

  19. Investigation of interfacial shear stresses, shape fixity, and actuation strain in composites incorporating shape memory polymers and shape memory alloys

    Directory of Open Access Journals (Sweden)

    Jungkyu ePark

    2015-03-01

    Full Text Available Shape memory composites (SMCs based on shape memory alloys (SMAs and shape memory polymers (SMPs allow many design possibilities due to their controllable temperature-dependent mechanical properties. The complementary characteristics of SMAs and SMPs can be utilized in systems with shape recovery created by the SMA and shape fixity provided by the SMP. In this research, three SMC operating regimes are identified and the behavior of SMC structures is analyzed by focusing on composite shape fixity and interfacial stresses. Analytical models show that SMPs can be used to adequately fix the shape of SMA actuators and springs. COMSOL finite element simulations are in agreement with analytical expressions for shape fixity and interfacial stresses. Analytical models are developed for an end-coupled linear SMP-SMA two-way actuator and the predicted strain is shown to be in good agreement with experimental test results.

  20. Deformation and Failure Mechanisms of Shape Memory Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Daly, Samantha Hayes [Univ. of Michigan, Ann Arbor, MI (United States)

    2015-04-15

    The goal of this research was to understand the fundamental mechanics that drive the deformation and failure of shape memory alloys (SMAs). SMAs are difficult materials to characterize because of the complex phase transformations that give rise to their unique properties, including shape memory and superelasticity. These phase transformations occur across multiple length scales (one example being the martensite-austenite twinning that underlies macroscopic strain localization) and result in a large hysteresis. In order to optimize the use of this hysteretic behavior in energy storage and damping applications, we must first have a quantitative understanding of this transformation behavior. Prior results on shape memory alloys have been largely qualitative (i.e., mapping phase transformations through cracked oxide coatings or surface morphology). The PI developed and utilized new approaches to provide a quantitative, full-field characterization of phase transformation, conducting a comprehensive suite of experiments across multiple length scales and tying these results to theoretical and computational analysis. The research funded by this award utilized new combinations of scanning electron microscopy, diffraction, digital image correlation, and custom testing equipment and procedures to study phase transformation processes at a wide range of length scales, with a focus at small length scales with spatial resolution on the order of 1 nanometer. These experiments probe the basic connections between length scales during phase transformation. In addition to the insights gained on the fundamental mechanisms driving transformations in shape memory alloys, the unique experimental methodologies developed under this award are applicable to a wide range of solid-to-solid phase transformations and other strain localization mechanisms.

  1. An Implicit Algorithm for the Numerical Simulation of Shape-Memory Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Becker, R; Stolken, J; Jannetti, C; Bassani, J

    2003-10-16

    Shape-memory alloys (SMA) have the potential to be used in a variety of interesting applications due to their unique properties of pseudoelasticity and the shape-memory effect. However, in order to design SMA devices efficiently, a physics-based constitutive model is required to accurately simulate the behavior of shape-memory alloys. The scope of this work is to extend the numerical capabilities of the SMA constitutive model developed by Jannetti et. al. (2003), to handle large-scale polycrystalline simulations. The constitutive model is implemented within the finite-element software ABAQUS/Standard using a user defined material subroutine, or UMAT. To improve the efficiency of the numerical simulations, so that polycrystalline specimens of shape-memory alloys can be modeled, a fully implicit algorithm has been implemented to integrate the constitutive equations. Using an implicit integration scheme increases the efficiency of the UMAT over the previously implemented explicit integration method by a factor of more than 100 for single crystal simulations.

  2. A Computationally-Efficient, Multi-Mechanism Based Framework for the Comprehensive Modeling of the Evolutionary Behavior of Shape Memory Alloys

    Science.gov (United States)

    Saleeb, Atef F.; Vaidyanathan, Raj

    2016-01-01

    The report summarizes the accomplishments made during the 4-year duration of the project. Here, the major emphasis is placed on the different tasks performed by the two research teams; i.e., the modeling activities by the University of Akron (UA) team and the experimental and neutron diffraction studies conducted by the University of Central Florida (UCF) team, during this 4-year period. Further technical details are given in the upcoming sections by UA and UCF for each of the milestones/years (together with the corresponding figures and captions).The project majorly involved the development, validation, and application of a general theoretical model that is capable of capturing the nonlinear hysteretic responses, including pseudoelasticity, shape memory effect, rate-dependency, multi-axiality, asymmetry in tension versus compression response of shape memory alloys. Among the targeted goals for the SMA model was its ability to account for the evolutionary character response (including transient and long term behavior under sustained cycles) for both conventional and high temperature (HT) SMAs, as well as being able to simulate some of the devices which exploit these unique material systems. This required extensive (uniaxial and multi-axial) experiments needed to guide us in calibrating and characterizing the model. Moreover, since the model is formulated on the theoretical notion of internal state variables (ISVs), neutron diffraction experiments were needed to establish the linkage between the micromechanical changes and these ISVs. In addition, the design of the model should allow easy implementation in large scale finite element application to study the behavior of devices making use of these SMA materials under different loading controls. Summary of the activities, progress/achievements made during this period is given below in details for the University of Akron and the University (Section 2.0) of Central Florida (Section 3.0).

  3. Properties and medical applications of shape memory alloys.

    Science.gov (United States)

    Tarniţă, Daniela; Tarniţă, D N; Bîzdoacă, N; Mîndrilă, I; Vasilescu, Mirela

    2009-01-01

    One of the most known intelligent material is nitinol, which offers many functional advantages over conventional implantable alloys. Applications of SMA to the biomedical field have been successful because of their functional qualities, enhancing both the possibility and the execution of less invasive surgeries. The biocompatibility of these alloys is one of their most important features. Different applications exploit the shape memory effect (one-way or two-way) and the super elasticity, so that they can be employed in orthopedic and cardiovascular applications, as well as in the manufacture of new surgical tools. Therefore, one can say that smart materials, especially SMA, are becoming noticeable in the biomedical field. Super elastic NiTi has become a material of strategic importance as it allows to overcome a wide range of technical and design issues relating to the miniaturization of medical devices and the increasing trend for less invasive and therefore less traumatic procedures. This paper will consider just why the main properties of shape memory alloys hold so many opportunities for medical devices and will review a selection of current applications.

  4. Constitutive modelling of magnetic shape memory alloys with discrete and continuous symmetries.

    Science.gov (United States)

    Haldar, K; Lagoudas, D C

    2014-09-08

    A free energy-based constitutive formulation is considered for magnetic shape memory alloys. Internal state variables are introduced whose evolution describes the transition from reference state to the deformed and transformed one. We impose material symmetry restrictions on the Gibbs free energy and on the evolution equations of the internal state variables. Discrete symmetry is considered for single crystals, whereas continuous symmetry is considered for polycrystalline materials.

  5. Design and development of novel antibacterial Ti-Ni-Cu shape memory alloys for biomedical application.

    Science.gov (United States)

    Li, H F; Qiu, K J; Zhou, F Y; Li, L; Zheng, Y F

    2016-11-29

    In the case of medical implants, foreign materials are preferential sites for bacterial adhesion and microbial contamination, which can lead to the development of prosthetic infections. Commercially biomedical TiNi shape memory alloys are the most commonly used materials for permanent implants in contact with bone and dental, and the prevention of infections of TiNi biomedical shape memory alloys in clinical cases is therefore a crucial challenge for orthopaedic and dental surgeons. In the present study, copper has been chosen as the alloying element for design and development novel ternary biomedical Ti‒Ni‒Cu shape memory alloys with antibacterial properties. The effects of copper alloying element on the microstructure, mechanical properties, corrosion behaviors, cytocompatibility and antibacterial properties of biomedical Ti‒Ni‒Cu shape memory alloys have been systematically investigated. The results demonstrated that Ti‒Ni‒Cu alloys have good mechanical properties, and remain the excellent shape memory effects after adding copper alloying element. The corrosion behaviors of Ti‒Ni‒Cu alloys are better than the commercial biomedical Ti‒50.8Ni alloys. The Ti‒Ni‒Cu alloys exhibit excellent antibacterial properties while maintaining the good cytocompatibility, which would further guarantee the potential application of Ti‒Ni‒Cu alloys as future biomedical implants and devices without inducing bacterial infections.

  6. Design and development of novel antibacterial Ti-Ni-Cu shape memory alloys for biomedical application

    Science.gov (United States)

    Li, H. F.; Qiu, K. J.; Zhou, F. Y.; Li, L.; Zheng, Y. F.

    2016-11-01

    In the case of medical implants, foreign materials are preferential sites for bacterial adhesion and microbial contamination, which can lead to the development of prosthetic infections. Commercially biomedical TiNi shape memory alloys are the most commonly used materials for permanent implants in contact with bone and dental, and the prevention of infections of TiNi biomedical shape memory alloys in clinical cases is therefore a crucial challenge for orthopaedic and dental surgeons. In the present study, copper has been chosen as the alloying element for design and development novel ternary biomedical Ti‒Ni‒Cu shape memory alloys with antibacterial properties. The effects of copper alloying element on the microstructure, mechanical properties, corrosion behaviors, cytocompatibility and antibacterial properties of biomedical Ti‒Ni‒Cu shape memory alloys have been systematically investigated. The results demonstrated that Ti‒Ni‒Cu alloys have good mechanical properties, and remain the excellent shape memory effects after adding copper alloying element. The corrosion behaviors of Ti‒Ni‒Cu alloys are better than the commercial biomedical Ti‒50.8Ni alloys. The Ti‒Ni‒Cu alloys exhibit excellent antibacterial properties while maintaining the good cytocompatibility, which would further guarantee the potential application of Ti‒Ni‒Cu alloys as future biomedical implants and devices without inducing bacterial infections.

  7. Novel tribological systems using shape memory alloys and thin films

    Science.gov (United States)

    Zhang, Yijun

    Shape memory alloys and thin films are shown to have robust indentation-induced shape memory and superelastic effects. Loading conditions that are similar to indentations are very common in tribological systems. Therefore novel tribological systems that have better wear resistance and stronger coating to substrate adhesion can be engineered using indentation-induced shape memory and superelastic effects. By incorporating superelastic NiTi thin films as interlayers between chromium nitride (CrN) and diamond-like carbon (DLC) hard coatings and aluminum substrates, it is shown that the superelasticity can improve tribological performance and increase interfacial adhesion. The NiTi interlayers were sputter deposited onto 6061 T6 aluminum and M2 steel substrates. CrN and DLC coatings were deposited by unbalanced magnetron sputter deposition. Temperature scanning X-ray diffraction and nanoindentation were used to characterize NiTi interlayers. Temperature scanning wear and scratch tests showed that superelastic NiTi interlayers improved tribological performance on aluminum substrates significantly. The two-way shape memory effect under contact loading conditions is demonstrated for the first time, which could be used to make novel tribological systems. Spherical indents in NiTi shape memory alloys and thin films had reversible depth changes that were driven by temperature cycling, after thermomechanical cycling, or one-cycle slip-plasticity deformation training. Reversible surface topography was realized after the indents were planarized. Micro- and nano- scale circular surface protrusions arose from planarized spherical indents in bulk and thin film NiTi alloy; line surface protrusions appeared from planarized scratch tracks. Functional surfaces with reversible surface topography can potentially result in novel tribological systems with reversible friction coefficient. A three dimensional constitutive model was developed to describe shape memory effects with slip

  8. Boriding of Binary Ni-Ti Shape Memory Alloys

    Science.gov (United States)

    Ucar, Nazim; Dogan, Sule; Karakas, Mustafa Serdar; Calik, Adnan

    2016-11-01

    Boriding of binary Ni-Ti shape memory alloys was carried out in a solid medium at 1273 K for 2, 4, 6, and 8 h using the powder pack method with proprietary Ekabor-Ni powders. Characterization of the boride layer formed on the surface of alloys was done by optical microscopy and scanning electron microscopy. The presence of boride, silicide, and borosilicide phases in the boride layers was confirmed by X-ray diffraction analysis. The thickness and microhardness of the boride layers increased with increasing boriding time. Hardness profiles showed a rapid decrease in hardness moving from the boride layer to the main structure. The high hardness of the boride layer was attributed mainly to the formation of TiB2. A parabolic relationship was observed between layer thickness and boriding time, and the growth rate constant for the boriding treatment was calculated as 0.62×10-8 cm2 s-1.

  9. Microestrutural evolution in a CuZnAl shape memory alloy: kinetics and morphological aspects

    Directory of Open Access Journals (Sweden)

    R.A. Sanguinetti Ferreira

    2000-10-01

    Full Text Available The microstructural evolution of the CuZnAl shape memory alloys was studied by indirect techniques relating to the atomic migration rate of grain boundaries. Addition elements were used in a Cu-15,5Zn-8,0Al alloy to provide a comparison with the same alloy without microelement additions. The alloys were melted in an induction furnace of 24 kVA. After casting, the bulk samples of the alloys were homogenized. Then they were solution treated and hot-rolled followed by water-quenching to initiate the recrystallization. Finally, annealing produced at different temperature ranges was made in different samples in order to establish a law for the grain growth. Following the heat treatments, all annealed samples were examined by statistical metallography and the grain sizes were measured. After measurements, the same empirical law of grain growth was found for the different alloys and the ln [D-Do] x 1/T diagrams were plotted in order to establish the kinetic behavior. Based on the estimated values of the activation energy, important conclusions were obtained concerning the addition elements.

  10. Modeling of effects of matrix on actuation characteristics of embedded shape memory alloy wires

    Institute of Scientific and Technical Information of China (English)

    CUI Xiao-long; ZHENG Yan-jun; CUI Li-shan

    2005-01-01

    Effects of matrix properties on the actuation characteristics of embedded shape memory alloy wires were studied. The coefficient of thermal expansion and the modulus of matrix have significant effect on the maximum recovery stress. The thermal strain rate of the SMA wires upon heating is more sensitive to the matrix properties than the stress rate does. Additional fibers embedded in the matrix have significant effect on the stress distribution between the SMA wires and the matrix, and thus affect the interface quality significantly. Fibers with negative thermal expansion coefficient are beneficial to the interface between shape memory alloy wires and the epoxy matrix. All conclusions based on the numerical modeling can find experimental supports.

  11. Investigation of the Thermomechanical Response of Shape Memory Alloy Hybrid Composite Beams

    Science.gov (United States)

    Davis, Brian A.

    2005-01-01

    Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical model. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. Excellent agreement is achieved between the predicted and measured results, thereby quantitatively validating the numerical tool.

  12. Topology Optimization of Shape Memory Alloy Actuators using Element Connectivity Parameterization

    DEFF Research Database (Denmark)

    Langelaar, Matthijs; Yoon, Gil Ho; Kim, Yoon Young

    2005-01-01

    This paper presents the first application of topology optimization to the design of shape memory alloy actuators. Shape memory alloys (SMA’s) exhibit strongly nonlinear, temperature-dependent material behavior. The complexity in the constitutive behavior makes the topology design of SMA structures...... intractable by the conventional element density-based topology optimization. Therefore, in the present study, the recently developed element connectivity parameterization (ECP) formulation is applied, which offers important advantages for complex nonlinear topology optimization problems. A history......) stiffness matrix of continuum finite elements. Therefore, any finite element code, including commercial codes, can be readily used for the ECP implementation. The key ideas and characteristics of these methods will be presented in this paper....

  13. Thermoelectric control of shape memory alloy microactuators: a thermal model

    Science.gov (United States)

    Abadie, J.; Chaillet, Nicolas; Lexcellent, Christian; Bourjault, Alain

    1999-06-01

    Microtechnologies and microsystems engineering use new active materials. These materials are interesting to realize microactuators and microsensors. In this category of materials, Shape Memory Alloys (SMA) are good candidates for microactuation. SMA wires, or thin plates, can be used as active material in microfingers. These microstructures are able to provide very important forces, but have low dynamic response, especially for cooling, in confined environment. The control of the SMA phase transformations, and then the mechanical power generation, is made by the temperature. The Joule effect is an easy and efficiency way to heat the SMA wires, but cooling is not so easy. The dynamic response of the actuator depends on cooling capabilities. The thermal convection and conduction are the traditional ways to cool the SMA, but have limitations for microsystems. We are looking for a reversible way of heating and cooling SMA microactuators, based on the thermoelectric effects. Using Peltier effect, a positive or a negative electrical courant is able to pump or produce heat, in the SMA actuator. A physical model based on thermal exchanges between a Nickel/Titanium (NiTi) SMA, and Bismuth/Telluride (Te3Bi2) thermoelectric material has been developed. For simulation, we use a numerical resolution of our model, with finite elements, which takes into account the Peltier effect, the Joule effect, the convection, the conduction and the phase transformation of the SMA. We have also developed the corresponding experimental system, with two thermoelectric junctions, where the SMA actuator is one of the element of each junction. In this paper, the physical model and its numerical resolution are given, the experimental system used to validate the model is described, and experimental results are shown.

  14. DSC study on temperature memory effect of NiTi shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    N. LIU; W. M. HUANG

    2006-01-01

    A systematic study on the temperature memory effect (TME) in a polycrystalline NiTi shape memory alloy was presented. The investigation was carried out through a series of differential scanning calorimeter (DSC) tests. Two types of tests were conducted,namely single-step test and multi-step test. The influence of the step temperature on the peak/trough temperatures in the subsequent heating process and the associated energy absorption/release in the phase transformations was investigated. Using a simple theoretical model,the exact mechanism behind TME was studied.

  15. Dynamic mechanical analyze of superelastic CuMnAl shape memory alloy

    Science.gov (United States)

    (Dragoș Ursanu, A. I.; Stanciu, S.; Pricop, B.; Săndulache, F.; Cimpoeșu, N.

    2016-08-01

    A new shape memory alloy was obtain from high purity Cu, Mn and Al elements using a induce furnace. The intelligent material present negative transformation temperatures and an austenite like state at room temperature. The austenite state of CuMnAl shape memory alloy present superelasticity property. Five kilograms ingot was obtain of Cu10Mn10Al alloy. From the base material (melted state) were cut samples with 6 mm thickness using a mechanical saw. After an homogenization heat treatment the samples were hot rolled through four passes with a reduction coefficient of 20%. Experimental lamellas were obtained with 1.5 mm thickness and 90x10 mm length and width. After the hot rolled treatment the materials were heat treated at 800°C for 20 minutes and chilled in water. Four samples, one just laminated and three heat treated by aging, were analyzed with a Netzsch DMA equipment to establish the elastic modulus and the internal friction values of the materials. Metallic materials microstructure was analyzed using a scanning electron microscope Vega Tescan LMH II type. After the aging heat treatment a decrease of internal friction is observed on the entire analyze range which is assigned to formation of Al-based precipitates that block the internal movement of the alloy characteristic phases.

  16. Influence of Tin Additions on the Phase-Transformation Characteristics of Mechanical Alloyed Cu-Al-Ni Shape-Memory Alloy

    Science.gov (United States)

    Saud, Safaa N.; Hamzah, E.; Abubakar, T.; Bakhsheshi-Rad, H. R.; Mohammed, M. N.

    2016-10-01

    The influence of the addition of Sn to Cu-Al-Ni alloy as a fourth element with different percentages of 0.5, 1.0, and 1.5 wt pct on the microstructure, phase-transformation temperatures, mechanical properties, and corrosion behaviors was investigated. The modified and unmodified alloys were fabricated by mechanical alloying followed by microwave sintering. The sintered and homogenized alloys of Cu-Al-Ni- xSn shape-memory alloys had a refined particle structure with an average particle size of 40 to 50 µm associated with an improvement in the mechanical properties and corrosion resistance. With the addition of Sn, the porosity density tends to decrease, which can also lead to improvements in the properties of the modified alloys. The minimum porosity percentage was observed in the Cu-Al-Ni-1.0 wt pct Sn alloy, which resulted in enhancing the ductility, strain recovery, and corrosion resistance. Further increasing the Sn addition to 1.5 wt pct, the strength of the alloy increased because the highest volume fraction of precipitates was formed. Regarding the corrosion behavior, addition of Sn up to 1 wt pct increased the corrosion resistance of the base SMA from 2.97 to 19.20 kΩ cm2 because of formation of a protective film that contains hydrated tin oxyhydroxide, aluminum dihydroxychloride, and copper chloride on the alloy. However, further addition of Sn reduced the corrosion resistance.

  17. Implement of Shape Memory Alloy Actuators in a Robotic Hand

    Directory of Open Access Journals (Sweden)

    Daniel Amariei

    2006-10-01

    Full Text Available This paper was conceived to present the ideology of utilizing advanced actuators to design and develop innovative, lightweight, powerful, compact, and as much as possible dexterous robotic hands. The key to satisfying these objectives is the use of Shape Memory Alloys (SMAs to power the joints of the robotic hand. The mechanical design of a dexterous robotic hand, which utilizes non-classical types of actuation and information obtained from the study of biological systems, is presented in this paper. The type of robotic hand described in this paper will be utilized for applications requiring low weight, power, compactness, and dexterity.

  18. Shape memory alloy heat engines and energy harvesting systems

    Science.gov (United States)

    Browne, Alan L; Johnson, Nancy L; Keefe, Andrew C; Alexander, Paul W; Sarosi, Peter Maxwell; Herrera, Guillermo A; Yates, James Ryan

    2013-12-17

    A heat engine includes a first rotatable pulley and a second rotatable pulled spaced from the first rotatable pulley. A shape memory alloy (SMA) element is disposed about respective portions of the pulleys at an SMA pulley ratio. The SMA element includes first spring coil and a first fiber core within the first spring coil. A timing cable is disposed about disposed about respective portions of the pulleys at a timing pulley ratio, which is different than the SMA pulley ratio. The SMA element converts a thermal energy gradient between the hot region and the cold region into mechanical energy.

  19. Characterization of shape memory alloys for safety mechanisms.

    Energy Technology Data Exchange (ETDEWEB)

    McLaughlin, Jarred T.; Buchheit, Thomas Edward; Massad, Jordan Elias

    2008-03-01

    Shape memory alloys (SMAs) are metals that exhibit large recoverable strains and exert large forces with tremendous energy densities. The behavior of SMAs is thermomechanically coupled. Their response to temperature is sensitive to their loading condition and their response to loading is sensitive to their thermal condition. This coupled behavior is not to be circumvented, but to be confronted and understood, since it is what manifests SMA's superior clamping performance. To reasonably characterize the coupled behavior of SMA clamping rings used in safety mechanisms, we conduct a series of experiments on SMA samples. The results of the tests will allow increased fidelity in modeling and failure analysis of parts.

  20. Stability of the magnetomechanical problem in magnetic shape memory alloys

    Science.gov (United States)

    Chatzigeorgiou, George; Haldar, Krishnendu; Lagoudas, Dimitris C.

    2010-04-01

    In this work we study the unstable phenomena that occur on Magnetic Shape Memory Alloys (MSMAs) during compression tests. Solving the coupled magnetomechanical problem we observe that during the reorientation process the material presents strong non-uniformity, in the form of localized zones, in the distribution of the magnetic, the stress and the strain field. This non-uniformity is due to loss of ellipticity of the coupled problem during the martensitic reorientation and affects significantly the reorientation process. The identification of the stability conditions of the magnetomechanical problem is achieved by performing stability analysis.

  1. Orthodontic applications of a superelastic shape-memory alloy model

    Energy Technology Data Exchange (ETDEWEB)

    Glendenning, R.W.; Enlow, R.L. [Otago Univ., Dunedin (New Zealand). Dept. of Math. and Stat.; Hood, J.A.A. [Dept. of Oral Sciences and Orthodontics, Univ. of Otago, Dunedin (New Zealand)

    2000-07-01

    During orthodontic treatment, dental appliances (braces) made of shape memory alloys have the potential to provide nearly uniform low level stresses to dentitions during tooth movement over a large range of tooth displacement. In this paper we model superelastic behaviour of dental appliances using the finite element method and constitutive equations developed by F. Auricchio et al. Results of the mathematical model for 3-point bending and several promising 'closing loop' designs are compared with laboratory results for the same configurations. (orig.)

  2. Application of Shape Memory Alloys in Facial Nerve Paralysis

    Directory of Open Access Journals (Sweden)

    M Vloeberghs

    2009-11-01

    Full Text Available The Facial Nerve can be damaged at a peripheral level by a stroke or, for example by trauma or infection within the faceor the ear. In these cases the facial muscles are paralysed with little or no chance of spontaneous recovery. This research focuses on the potential utilisation of a Shape Memory Alloy(SMA to replace the function of the Facial Nerve, which willallow in conjunction with passive reconstructive methods, a patient to regain limited but active movement of the mouthcorner. Paralysis of the mouth corner is a very disabling bothfunctionally and cosmetically, speech and swallowing are hampered and the patient loses saliva, with presents a social problem.

  3. A sharp interface evolutionary model for shape memory alloys

    Science.gov (United States)

    Knüpfer, Hans; Kružík, Martin

    2016-11-01

    We show the existence of an energetic solution to a quasistatic evolutionary model of shape memory alloys. Elastic behavior of each material phase/variant is described by polyconvex energy density. Additionally, to every phase boundary, there is an interface-polyconvex energy assigned, introduced by M. \\v{S}ilhav\\'{y}. The model considers internal variables describing the evolving spatial arrangement of the material phases and a deformation mapping with its first-order gradients. It allows for injectivity and orientation-preservation of deformations. Moreover, the resulting material microstructures have finite length scales.

  4. On phase transformation behavior of porous Shape Memory Alloys.

    Science.gov (United States)

    Liu, Bingfei; Dui, Guansuo; Zhu, Yuping

    2012-01-01

    This paper is concerned on the phase transformation mechanism of porous Shape Memory Alloys (SMAs). A unit-cell model is adopted to establish the constitutive relation for porous SMAs, the stress distributions, the phase distributions and the martensitic volume fractions for the model are then derived under both pure hydrostatic stress and uniaxial compression. Further, an example for the uniaxial response under compression for a porous Ni-Ti SMA material considering hydrostatic stress is supplied. Good agreement between the theoretical prediction of the proposed model and published experimental data is observed. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  5. Properties of Porous TiNbZr Shape Memory Alloy Fabricated by Mechanical Alloying and Hot Isostatic Pressing

    Science.gov (United States)

    Ma, L. W.; Chung, C. Y.; Tong, Y. X.; Zheng, Y. F.

    2011-07-01

    In the past decades, systematic researches have been focused on studying Ti-Nb-based SMAs by adding ternary elements, such as Mo, Sn, Zr, etc. However, only arc melting or induction melting methods, with subsequent hot or cold rolling, were used to fabricate these Ni-free SMAs. There is no work related to powder metallurgy and porous structures. This study focuses on the fabrication and characterization of porous Ti-22Nb-6Zr (at.%) shape memory alloys produced using elemental powders by means of mechanical alloying and hot isostatic pressing. It is found that the porous Ti-22Nb-6Zr alloys prepared by the HIP process exhibit a homogenous pore distribution with spherical pores, while the pores have irregular shape in the specimen prepared by conventional sintering. X-ray diffraction analysis showed that the solid solution-treated Ti-22Nb-6Zr alloy consists of both β phase and α″ martensite phase. Morphologies of martensite were observed. Finally, the porous Ti-22Nb-6Zr SMAs produced by both MA and HIP exhibit good mechanical properties, such as superior superelasticity, with maximum recoverable strain of ~3% and high compressive strength.

  6. Experimental analyses of dynamical systems involving shape memory alloys

    DEFF Research Database (Denmark)

    Enemark, Søren; Savi, Marcelo A.; Santos, Ilmar F.

    2015-01-01

    The use of shape memory alloys (SMAs) in dynamical systems has an increasing importance in engineering especially due to their capacity to provide vibration reductions. In this regard, experimental tests are essential in order to show all potentialities of this kind of systems. In this work, SMA...... springs are incorporated in a dynamical system that consists of a one degree of freedom oscillator connected to a linear spring and a mass, which is also connected to the SMA spring. Two types of springs are investigated defming two distinct systems: a pseudoelastic and a shape memory system......-tension of the springs. This article shows several experimental tests that allow one to obtain a general comprehension of the dynamical behaviour of SMA systems. Results show the general thermo-mechanical behaviour of SMA dynamical systems and the obtained conclusions can be applied in distinct situations as in rotor...

  7. Modeling of Functional Properties of Porous Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Volkov Aleksandr E.

    2015-01-01

    Full Text Available A model accounting for the microstructure of porous TiNi shape memory alloy samples fabricated by self-propagating high temperature synthesis has been proposed for simulation of their functional-mechanical properties. Structural elements of a porous sample have been approximated by curved beams. An analysis of shapes and sizes of pores and ligaments permitted to identify characteristic sizes of the beams. A mathematical object consisting of rigidly connected small curve beams has been considered. The stress-strain state of a beam was estimated by the classical methods of strength of materials. The microstructural model was used for calculation of the phase deformation of the shape memory material. Simulation of stress-strain curves and phase deformation of a porous TiNi sample on cooling and heating under a constant stress has shown a good correspondence between the experimental data and the results of modeling.

  8. Porous shape memory alloy scaffolds for biomedical applications: a review

    Energy Technology Data Exchange (ETDEWEB)

    Wen, C E; Xiong, J Y; Li, Y C; Hodgson, P D [Institute for Technology Research and Innovation, Deakin University, Waurn Ponds, VIC 3217 (Australia)

    2010-05-01

    The interest in using porous shape memory alloy (SMA) scaffolds as implant materials has been growing in recent years due to the combination of their unique mechanical and functional properties, i.e. shape memory effect and superelasticity, low elastic modulus combined with new bone tissue ingrowth ability and vascularization. These attractive properties are of great benefit to the healing process for implant applications. This paper reviews current state-of-the art on the processing, porous characteristics and mechanical properties of porous SMAs for biomedical applications, with special focus on the most widely used SMA nickel-titanium (NiTi), including (i) microstructural features, mechanical and functional properties of NiTi SMAs; (ii) main processing methods for the fabrication of porous NiTi SMAs and their mechanical properties and (iii) new-generation Ni-free, biocompatible porous SMA scaffolds.

  9. Phase transformation behaviors and shape memory effects of TiNiFeAl shape memory alloys

    Institute of Scientific and Technical Information of China (English)

    Li Xiao; Fushun Liu; Huibin Xu

    2007-01-01

    Measurements of electrical resistivity, X-ray diffraction, and tensile test at room temperature and -196℃ were performed to investigate the effects of Al addition substituting Ni on the phase transformation behaviors, the mechanical properties, and the shape memory effects of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys. It is found that 1at% Al addition dramatically decreases the martensitic start transformation temperature and expands the transformation temperature range of R-phase for TiNiFeAl alloys. The results of tensile test indicate that 1at% Al improves the yield strength of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys by 40% and 64%, but decreases the plasticity to 11% and 12% from 26% and 27% respectively. Moreover, excellent shape memory effect of 6.6% and 7.5% were found in Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.sAl1 alloys, which results from the stress-induced martensite transformation from the R-phase.

  10. Cyclic response of shape memory alloy smart composite beams

    Science.gov (United States)

    Friend, Clifford M.; Morgan, Neil B.

    1994-09-01

    'Smart' structure are an emerging technology which will provide the possibility of engineering structures with enhanced functionality for a wide range of applications. In most current Smart Structural Concepts a mechatronic or 'Frankenstein' approach is adopted where separate sensors, signal processing and actuators are 'bolted-together' to produce a 'Smart' system response. In the majority of these concepts the sensors and actuators are integrated within the host structure itself, and many of the sensor and actuator materials are familiar from other more conventional sensing/actuation applications. Amongst the materials used/proposed for actuators are Shape- Memory Alloys (SMAs) since these materials offer a range of attractive properties, including the possibility of high strain/stress actuation. The literature-base on the integration of SMA actuators into composite structures is not extensive. However, their use has been investigated for vibration [1], acoustic radiation [1,2], damage [3], buckling [1,2], and shape [1] control. An interesting feature of this work has been a heavy bias towards modelling, with only limited attempts to experimentally verify the calculated results. Previous work has also failed to produce a systematic database on one other key issue. This is the durability of SPA hybrid composites. The present work was therefore undertaken to provide a preliminary appraisal of the durability issues associated with the use of SMA hybrid composites. This work addressed a number of issues including (i) the effect of actuator fraction on strain outputs, (ii) the effect of actuator fraction and maximum strain on the cyclic stability of shape changes, and (iii) the effect of these variables on damage accumulation within the hybrid structures.

  11. Kinetic arrest behavior in martensitic transformation of NiCoMnSn metamagnetic shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Umetsu, R.Y., E-mail: rieume@imr.tohoku.ac.jp [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Sendai 980-8577 (Japan); Ito, K.; Ito, W. [Department of Materials Science, Graduate School of Engineering, Tohoku University, 6-6-02 Aoba, Sendai 980-8579 (Japan); Koyama, K. [High Field Laboratory for Superconducting Materials, Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Kanomata, T. [Faculty of Engineering, Tohoku Gakuin University, Tagajo 985-8537 (Japan); Ishida, K.; Kainuma, R. [Department of Materials Science, Graduate School of Engineering, Tohoku University, 6-6-02 Aoba, Sendai 980-8579 (Japan)

    2011-02-03

    Research highlights: > NiMnZ (Z = Ga, Al, In, Sn, Sb) Heusler alloys are now very attractive because of their unique physical properties, such as, magnetic shape memory effect, magnetic field-induced phase transition, inverse magnetocaloric effect, magnetoresistance effect and the giant magnetothermal conductivity. > In our previous investigations for the NiCoMnSn alloy, the behavior of the shape recovery due to the magnetic field induced reverse transformation has been reported. However, the detailed investigations on the magnetic properties such as metamagnetic behavior have not been made. > In our present manuscript, we show the experimental results of the magnetic properties under the magnetic fields up to 12 T for NiCoMnSn alloy. We demonstrated the kinetic arresting behavior of the martensitic transformation under the high magnetic fields and thermodynamically discussed it. In addition, we analyzed the structure of the martensitic phase with a long period stacking structure and showed a lattice change between the before and the after the martensitic transformation. We believe that these results are high importance for understanding the interesting physical properties of the Ni-based ferromagnetic shape memory alloys and its applications. - Abstract: High-field magnetic measurements were carried out in order to investigate behaviors of field-induced reverse martensitic transformation and kinetic arrest of NiCoMnSn metamagnetic shape memory alloy. In the thermomagnetization curves, it was confirmed that the reverse martensitic transformation temperature decreases 67 K by applying magnetic field of 5 T, while in the magnetic field cooling process under 5 T, martensitic transformation does not occur down to low temperatures. Equilibrium magnetic field, defined from the critical magnetic fields of the metamagnetic evidence in the magnetization curves, exhibits almost constant below about 100 K, suggesting that the entropy change becomes zero, which is considered

  12. Recent breakthrough development of the magnetic shape memory effect in Ni Mn Ga alloys

    Science.gov (United States)

    Söderberg, O.; Ge, Y.; Sozinov, A.; Hannula, S.-P.; Lindroos, V. K.

    2005-10-01

    Magnetic shape memory (MSM) alloys or ferromagnetic shape memory alloy (FSMA) materials discovered by Ullakko et al (1996 Appl. Phys. Lett. 69 1966-8) have received increasing interest, since they can produce a large strain with rather high frequencies without a change in the external temperature. These materials have potential for actuator and sensor applications. MSM materials exhibit giant magnetic field induced strain (MFIS) based on the rearrangements of the crystallographic domains (twin variants). The magnetization energy of the material is lowered when such twin variants that have the easy axis of magnetization along the field start to grow due to twin boundary motion. Currently, the best working MSM materials are the near-stoichiometric Ni2MnGa Heusler alloys in which the properties are highly composition dependent. Their modulated martensitic structures, 5M and 7M, show 6% or 10% response respectively in a magnetic field less than 800 kA m-1. The MSM service temperature of the 5M alloys is between 150 and 333 K, and the optimal frequency region is up to 500 Hz. The fatigue life of the MSM elements has been shown to be at least 50 × 106 shape change cycles. This paper reviews the research work carried out at Helsinki University of Technology on MSM materials since 1998.

  13. Analysis of uniaxial behavior of an Fe-based shape memory alloy under cyclic thermomechanical loading; Netsu rikigakuteki kurikaeshi fuka no moto deno tetsuki keijo kioku gokin no tanjiku henkei/hentai kyodo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, F.; Watanabe, N.; Tanaka, K. [Tokyo Metropolitan Institute of Technology, Tokyo (Japan)

    1997-08-15

    The thermomechanical hysteretic behavior of an Fe-based shape memory alloy is phenomenologically analyzed under cyclic uniaxial tensile and compressive loading. The shift of the stress-strain-temperature hysteresis loop, expressed by means of the evolution of the residual strain, is well explained by the theory with some internal variables. The accumulated perfect dislocations formed as a result of the interaction of martensite plates is one of the internal variables introduced here. The back stress is also employed as an internal variable to be the driving force for the shape recovery for the martensite plates. The simulations describe well the hysteretic behavior under the strain and stress-controlled cyclic thermomechanical loading; the shift of a loop, evolution of the residual strain and the change in transformation stress. 21 refs., 10 figs., 1 tab.

  14. Shake table tests and analytical simulations of a steel structure with shape memory alloy dampers

    Science.gov (United States)

    Parulekar, Y. M.; Kiran, A. Ravi; Reddy, G. R.; Singh, R. K.; Vaze, K. K.

    2014-12-01

    This study uses the pseudoelastic properties of Ni-Ti shape memory alloy wires for attenuation of the seismic response of a steel structure and evaluates its effectiveness and applicability in seismic response control. In this paper, shake table tests, carried out on a model of a steel structure with and without wire-based shape memory alloy dampers, are discussed in detail. Shake table tests, comprised of free vibration tests and spectrum compatible time history tests, were carried out. The former were used for the evaluation of the frequency and damping, and the later were used to prove the efficacy of the shape memory alloy dampers. Further analytical simulations are carried out using detailed time history analysis utilizing a thermomechanical model of an SMA and taking into account the residual martensite accumulation, which is irreversibly due to cyclic forward/reverse martensitic transformation. Moreover, a simple iterative response spectrum (IRS) method with equivalent damping and stiffness is also used to evaluate the response of the structure with SMA dampers, and it is proved that the method can be conservatively used by designers.

  15. Experimental evaluation of shape memory alloy actuation technique in adaptive antenna design concepts

    Science.gov (United States)

    Kefauver, W. Neill; Carpenter, Bernie F.

    1994-01-01

    Creation of an antenna system that could autonomously adapt contours of reflecting surfaces to compensate for structural loads induced by a variable environment would maximize performance of space-based communication systems. Design of such a system requires the comprehensive development and integration of advanced actuator, sensor, and control technologies. As an initial step in this process, a test has been performed to assess the use of a shape memory alloy as a potential actuation technique. For this test, an existing, offset, cassegrain antenna system was retrofit with a subreflector equipped with shape memory alloy actuators for surface contour control. The impacts that the actuators had on both the subreflector contour and the antenna system patterns were measured. The results of this study indicate the potential for using shape memory alloy actuation techniques to adaptively control antenna performance; both variations in gain and beam steering capabilities were demonstrated. Future development effort is required to evolve this potential into a useful technology for satellite applications.

  16. Transformation-induced plasticity in high-temperature shape memory alloys: a one-dimensional continuum model

    Science.gov (United States)

    Sakhaei, Amir Hosein; Lim, Kian-Meng

    2016-07-01

    A constitutive model based on isotropic plasticity consideration is presented in this work to model the thermo-mechanical behavior of high-temperature shape memory alloys. In high-temperature shape memory alloys (HTSMAs), both martensitic transformation and rate-dependent plasticity (creep) occur simultaneously at high temperatures. Furthermore, transformation-induced plasticity is another deformation mechanism during martensitic transformation. All these phenomena are considered as dissipative processes to model the mechanical behavior of HTSMAs in this study. The constitutive model was implemented for one-dimensional cases, and the results have been compared with experimental data from thermal cycling test for actuator applications.

  17. Effect of chemical component on shape memory effect of Fe-Mn-Si-Ni-C-RE shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    Naichao Si; Zhihong Jia; Longbiao Qi

    2004-01-01

    Effect of chemical component on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloys was studied by bent measurement, thermal cycle training, SEM etc. Results of study indicate that the alloys with high Mn content (25%) appeare better SME, especially in lower strain. SME improves evidently when Si is higher content, especially it′s range from 3% up to 4%.But brittleness of Fe-Mn-Si-Ni-C-RE alloy increases by increasing the Si content. SME of the alloy is weakening gradually as carbon content increases under small strain (3%). But in the condition of large strain (above 6%), SME of the alloy whose carbon content ranges from 0.1% to 0.12% shows small decreasing range, especially of alloy with the addition of compound RE.

  18. Mg based alloys obtained by mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez, S. [Univ. de Santiago de Chile (Chile). Fac. de Ingenieria; Garcia, G.; Serafini, D.; San Martin, A.

    1999-07-01

    In the present work, we studied the production of magnesium alloys, of stoichiometry 2Mg + Ni, by mechanical alloying (MA) and the behavior of the alloys under hydrogen in a Sievert`s type apparatus. The elemental powders were milled under argon atmosphere in a Spex 8000 high energy ball mill. The milled materials were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Only minimum amounts of the Mg{sub 2}Ni intermetallic compound was obtained after 22 h of milling time. Most of the material was sticked to the inner surface of the container as well as to the milling balls. Powders milled only for 12 hours transforms to the intermetallic at around 433 K. Effects of the MA on the hydrogen absorption kinetics were also studied. (orig.) 10 refs.

  19. Two-way shape memory effect and its stability in Ti-Ni-Hf high temperature shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    MENG Xiang-long; WU Ye; CAI Wei; ZHAO Lian-cheng

    2005-01-01

    The two-way shape memory effect (TWSME) in a Ti36 Ni49 Hf15 high temperature shape memory alloy (SMA) was systematically studied by bending tests. In the TiNiHf alloy, the martensite deformation is an effective method to get two-way shape memory effect even with a small deformation strain. The results indicate that the internal stress field formed by the bending deformation is in the direction of the preferentially oriented martensite variants formed during the bending deformation. Upon cooling the preferentially oriented martensite variants form under such an oriented stress field, which should be responsible for the generation of the two-way shape memory effect.Proper training process benefits the formation of the oriented stress field, resulting in the improvement of the twoway shape memory effect. A maximum TWSME of 0.88 % is obtained in the present alloy.

  20. Characterization of Transformation-Induced Defects in Nickel Titanium Shape Memory Alloys

    Science.gov (United States)

    Bowers, Matthew L.

    Shape memory alloys have remarkable strain recovery properties that make them ideal candidates for many applications that include devices in the automotive, aerospace, medical, and MEMS industries. Although these materials are widely used today, their performance is hindered by poor dimensional stability resulting from cyclic degradation of the martensitic transformation behavior. This functional fatigue results in decreased work output and cyclic accumulation of permanent strain. To date, few studies have taken a fundamental approach to investigating the interaction between plasticity and martensite growth and propagation, which is vitally important to mitigating functional fatigue in future alloy development. The current work focuses on understanding the interplay of these deformation mechanisms in NiTi-based shape memory alloys under a variety of different thermomechanical test conditions. Micron-scale compression testing of NiTi shape memory alloy single crystals is undertaken in an effort to probe the mechanism of austenite dislocation generation. Mechanical testing is paired with post mortem defect analysis via diffraction contrast scanning transmission electron microscopy (STEM). Accompanied by micromechanics-based modeling of local stresses surrounding a martensite plate, these results demonstrate that the previously existing martensite and resulting austenite dislocation substructure are intimately related. A mechanism of transformation-induced dislocation generation is described in detail. A study of pure and load-biased thermal cycling of bulk polycrystalline NiTi is done for comparison of the transformation behavior and resultant defects to the stress-induced case. Post mortem and in situ STEM characterization demonstrate unique defect configurations in this test mode and STEM-based orientation mapping reveals local crystal rotation with increasing thermal cycles. Changes in both martensite and austenite microstructures are explored. The results for

  1. Thermal response of novel shape memory polymer-shape memory alloy hybrids

    Science.gov (United States)

    Rossiter, Jonathan; Takashima, Kazuto; Mukai, Toshiharu

    2014-03-01

    Shape memory polymers (SMP) and shape memory alloys (SMA) have both been proven important smart materials in their own fields. Shape memory polymers can be formed into complex three-dimensional structures and can undergo shape programming and large strain recovery. These are especially important for deployable structures including those for space applications and micro-structures such as stents. Shape memory alloys on the other hand are readily exploitable in a range of applications where simple, silent, light-weight and low-cost repeatable actuation is required. These include servos, valves and mobile robotic artificial muscles. Despite their differences, one important commonality between SMPs and SMAs is that they are both typically activated by thermal energy. Given this common characteristic it is important to consider how these two will behave when in close environmental proximity, and hence exposed to the same thermal stimulus, and when they are incorporated into a hybrid SMA-SMP structure. In this paper we propose and examine the operation of SMA-SMP hybrids. The relationship between the two temperatures Tg, the glass transition temperature of the polymer, and Ta, the nominal austenite to martensite transition temperature of the alloy is considered. We examine how the choice of these two temperatures affects the thermal response of the hybrid. Electrical stimulation of the SMA is also considered as a method not only of actuating the SMA but also of inducing heating in the surrounding polymer, with consequent effects on actuator behaviour. Likewise by varying the rate and degree of thermal stimulation of the SMA significantly different actuation and structural stiffness can be achieved. Novel SMP-SMA hybrid actuators and structures have many ready applications in deployable structures, robotics and tuneable engineering systems.

  2. Pitting Corrosion of Cu-Zn-Al Shape Memory Alloy in Simulated Uterine Fluid

    Institute of Scientific and Technical Information of China (English)

    Bangyi CHEN; Chenghao LIANG; Daojun FU

    2005-01-01

    Electrochemical test technology and surface analysis method were employed to investigate the pitting corrosion of Cu-Zn-Al shape memory alloy in simulated uterine fluid. The results showed that the breakage of the breakingrenovating equilibrium of surface layers resulted in the pitting corrosion of Cu-Zn-Al shape memory alloy in simulated uterine fluid. The development of pitting corrosion was controlled by dissolution of surface layers. The critical pitting corrosion potential was 1.70 VsCE. The kinetics equation for the development of pitting corrosion for Cu-Zn-Al shape memory alloy in simulated uterine fluid was i0=465.68 t-0.5+1.5. Pitting appearances of pits could be two types: tortoise-shell, and anomaly abscess. Cl- ion facilitated the pitting corrosion of Cu-Zn-Al shape memory alloy by competing adsorption and concentrating on alloy surface at high positive potential.

  3. Study of a Ti Ni-based shape memory alloy aiming applications in pipeline connections of the oil and gas industry; Estudo de uma liga base Ti-Ni com memoria de forma visando aplicacoes em conexoes de tubulacoes na industria do petroleo e gas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M.M. da; Silva, N.J. da; Gomes, A.A.C.; Reis, R.P.B.; Araujo, C.J. de; Santos, M.A. dos [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Lab. Multidisciplinar de Materiais e Estruturas Ativas (LaMMEA)], e-mail: carlos@dem.ufcg.edu.br

    2006-07-01

    The objective of this paper is to study the technical feasibility of a TiNi-based Shape Memory Alloy (SMA) with potential application in connections of the oil and gas Sector. The employment of this alloy would increase the reliability of these unions. Thus, a 45,0 Ti-55,0 Ni (% wt) SMA has been manufactured through the plasma skull melting and with subsequent conformation by the Push-Pull method. Samples of this SMA were heat treated at 1173 K during 900s, followed by water quenching. These samples were characterized by optic microscopy, microhardness, differential scanning calorimetry (DSC), and force generation tests. The obtained TiNi SMA has presented an important wide temperature hysteresis. The generated forces substantiate the potential application of these alloys in connection systems of the oil and gas Sector. (author)

  4. Nanoscale design of Ni-Al shape memory alloys.

    Science.gov (United States)

    Subramaniyan, Arun K; Sun, C T

    2009-02-25

    Nanoscale design of Ni-Al alloys was performed to optimize the phase transformation behavior. The distribution of nickel and aluminum atoms was identified as a key parameter in the phase transformation process. A design criterion based on thermal expansion asymmetry was proposed. The effectiveness of the design criterion was validated using molecular dynamics simulations.

  5. Shape memory alloys applied to improve rotor-bearing system dynamics - an experimental investigation

    DEFF Research Database (Denmark)

    Enemark, Søren; Santos, Ilmar; Savi, Marcelo A.

    2015-01-01

    tor-bearing systems have critical speeds and to pass through them is an ongoing challenge in the field of mechanical engineering. The incorporation of shape memory alloys in rotating systems has an increasing importance to improve system performance and to avoid potential damaging situations when...... passing through critical speeds. In this work, the feasibility of applying shape memory alloys to a rotating system is experimentally investigated. Shape memory alloys can change their stiffness with temperature variations and thus they may change system dynamics. Shape memory alloys also exhibit...... hysteretic stress-strain relations which may be utilized for damping purposes. These ideas are tested in this study on a dedicated test-rig, consisting of a rigid shaft and disc held vertically by passive magnetic bearings, where the damping is low. The bearing housings is flexibly supported by shape memory...

  6. Characterization of Stoichiometric and Aging Effects on NiTiHf High Temperature Shape Memory Alloys

    Science.gov (United States)

    Coughlin, Daniel Robert

    NiTiHf ternary alloys exhibit attractive high temperature shape memory alloy (HTSMA) properties. Material properties include moderate transformation strain, relatively high transformation temperature, stable pseudoelastic (PE) behavior, and very small irrecoverable strain during load biased tests. The addition of Hf is more attractive than Pt and Pd due to the fact that Hf has a lower cost. Four NiTiHf alloys with different chemical compositions spanning stoichiometry were used to analyze microstructure and mechanical behavior. Research will mainly be focused on the Ni-rich alloys based on that the Ni-lean alloys do not exhibit the previously mentioned HTSMA material properties. The alloys analyzed all had 20(at.)% Hf with varying Ti concentrations (29(at.)%, 29.7(at.)%, 30(at.)%, and 30.5(at.)%). All of the alloys were formed by induction melting, homogenized at 1050C for 72hrs, and then hot extruded with a diameter reduction of 7:1 at a temperature of 900C. In addition to the homogenized and extruded condition, several short-term aging cycles above 400C were completed on each of the alloys. Certain microstructure and mechanical properties are obtained when Hf is added to NiTi and a proper aging cycle is used. Results from isothermal compression tests that were executed above the austenite finish temperature determined that the Ni-rich NiTiHf alloys exhibited all the necessary properties to be considered for HTSMA applications. The test temperature range of the isothermal compression tests were chosen to characterize the transition from PE behavior to austenite plasticity and to examine the deformation behavior of the B2 phase at high temperatures. Results from compression tests showed a strengthening effect when the test temperature was increased through the PE test region. The strengthening effect is due to the yield stress and plasticity being related to the stress induced martensite that is created during the compression test executed above the austenite

  7. A Constitutive Model for Superelastic Shape Memory Alloys Considering the Influence of Strain Rate

    Directory of Open Access Journals (Sweden)

    Hui Qian

    2013-01-01

    Full Text Available Shape memory alloys (SMAs are a relatively new class of functional materials, exhibiting special thermomechanical behaviors, such as shape memory effect and superelasticity, which enable their applications in seismic engineering as energy dissipation devices. This paper investigates the properties of superelastic NiTi shape memory alloys, emphasizing the influence of strain rate on superelastic behavior under various strain amplitudes by cyclic tensile tests. A novel constitutive equation based on Graesser and Cozzarelli’s model is proposed to describe the strain-rate-dependent hysteretic behavior of superelastic SMAs at different strain levels. A stress variable including the influence of strain rate is introduced into Graesser and Cozzarelli’s model. To verify the effectiveness of the proposed constitutive equation, experiments on superelastic NiTi wires with different strain rates and strain levels are conducted. Numerical simulation results based on the proposed constitutive equation and experimental results are in good agreement. The findings in this paper will assist the future design of superelastic SMA-based energy dissipation devices for seismic protection of structures.

  8. Memory-Based Shallow Parsing

    OpenAIRE

    Sang, Erik F. Tjong Kim

    2002-01-01

    We present memory-based learning approaches to shallow parsing and apply these to five tasks: base noun phrase identification, arbitrary base phrase recognition, clause detection, noun phrase parsing and full parsing. We use feature selection techniques and system combination methods for improving the performance of the memory-based learner. Our approach is evaluated on standard data sets and the results are compared with that of other systems. This reveals that our approach works well for ba...

  9. Dynamical Jumps in a Shape Memory Alloy Oscillator

    Directory of Open Access Journals (Sweden)

    H. S. Oliveira

    2014-01-01

    Full Text Available The dynamical response of systems with shape memory alloy (SMA elements presents a rich behavior due to their intrinsic nonlinear characteristic. SMA’s nonlinear response is associated with both adaptive dissipation related to hysteretic behavior and huge changes in properties caused by phase transformations. These characteristics are attracting much technological interest in several scientific and engineering fields, varying from medical to aerospace applications. An important characteristic associated with dynamical response of SMA system is the jump phenomenon. Dynamical jumps result in abrupt changes in system behavior and its analysis is essential for a proper design of SMA systems. This paper discusses the nonlinear dynamics of a one degree of freedom SMA oscillator presenting pseudoelastic behavior and dynamical jumps. Numerical simulations show different aspects of this kind of behavior, illustrating its importance for a proper understanding of nonlinear dynamics of SMA systems.

  10. Shape memory alloy heat engines and energy harvesting systems

    Energy Technology Data Exchange (ETDEWEB)

    Browne, Alan L; Johnson, Nancy L; Shaw, John Andrew; Churchill, Christopher Burton; Keefe, Andrew C; McKnight, Geoffrey P; Alexander, Paul W; Herrera, Guillermo A; Yates, James Ryan; Brown, Jeffrey W

    2014-09-30

    A heat engine includes a first rotatable pulley and a second rotatable pulley spaced from the first rotatable pulley. A shape memory alloy (SMA) element is disposed about respective portions of the pulleys at an SMA pulley ratio. The SMA element includes a first wire, a second wire, and a matrix joining the first wire and the second wire. The first wire and the second wire are in contact with the pulleys, but the matrix is not in contact with the pulleys. A timing cable is disposed about respective portions of the pulleys at a timing pulley ratio, which is different than the SMA pulley ratio. The SMA element converts a thermal energy gradient between the hot region and the cold region into mechanical energy.

  11. Shape memory alloy actuated adaptive exhaust nozzle for jet engine

    Science.gov (United States)

    Song, Gangbing (Inventor); Ma, Ning (Inventor)

    2009-01-01

    The proposed adaptive exhaust nozzle features an innovative use of the shape memory alloy (SMA) actuators for actively control of the opening area of the exhaust nozzle for jet engines. The SMA actuators remotely control the opening area of the exhaust nozzle through a set of mechanism. An important advantage of using SMA actuators is the reduction of weight of the actuator system for variable area exhaust nozzle. Another advantage is that the SMA actuator can be activated using the heat from the exhaust and eliminate the need of other energy source. A prototype has been designed and fabricated. The functionality of the proposed SMA actuated adaptive exhaust nozzle is verified in the open-loop tests.

  12. Simulation of grain size effects in nanocrystalline shape memory alloys

    Science.gov (United States)

    Ahluwalia, Rajeev; Quek, Siu Sin; Wu, David T.

    2015-06-01

    Recently, it has been demonstrated that martensitic transformation in nanocrystalline shape memory alloys can be suppressed for small grain sizes. Motivated by these results, we study the grain size dependence of martensitic transformations and stress-strain response of nanocrystalline shape memory alloys within the framework of the Ginzburg-Landau (GL) theory. A GL model for a square to rectangle transformation in polycrystals is extended to account for grain boundary effects. We propose that an inhibition of the transformation in grain boundary regions can occur, if the grain boundary energy of the martensite is higher than that of the austenite phase. We show that this inhibition of transformation in grain boundary regions has a strong influence on domain patterns inside grains. Although the transformation is inhibited only at the grain boundaries, it leads to a suppression of the transformation even inside the grains as grain size is decreased. In fact, below a critical grain size, the transformation can be completely suppressed. We explain these results in terms of the extra strain gradient cost associated with grain boundaries, when the transformation is inhibited at grain boundaries. On the other hand, no significant size effects are observed when transformation is not inhibited at grain boundaries. We also study the grain size dependence of the stress strain curve. It is found that when the transformation is inhibited at grain boundaries, a significant reduction in the hysteresis associated with stress-strain curves during the loading-unloading cycles is observed. The hysteresis for this situation reduces even further as the grain size is reduced, which is consistent with recent experiments. The simulations also demonstrate that the mechanical behavior is influenced by inter-granular interactions and the local microstructural neighbourhood of a grain has a stronger influence than the orientation of the grain itself.

  13. Shape memory alloy resetable spring lift for pedestrian protection

    Science.gov (United States)

    Barnes, Brian M.; Brei, Diann E.; Luntz, Jonathan E.; Strom, Kenneth; Browne, Alan L.; Johnson, Nancy

    2008-03-01

    Pedestrian protection has become an increasingly important aspect of automotive safety with new regulations taking effect around the world. Because it is increasingly difficult to meet these new regulations with traditional passive approaches, active lifts are being explored that increase the "crush zone" between the hood and rigid under-hood components as a means of mitigating the consequences of an impact with a non-occupant. Active lifts, however, are technically challenging because of the simultaneously high forces, stroke and quick timing resulting in most of the current devices being single use. This paper introduces the SMArt (Shape Memory Alloy ReseTable) Spring Lift, an automatically resetable and fully reusable device, which couples conventional standard compression springs to store the energy required for a hood lift, with Shape Memory Alloys actuators to achieve both an ultra high speed release of the spring and automatic reset of the system for multiple uses. Each of the four SMArt Device subsystems, lift, release, lower and reset/dissipate, are individually described. Two identical complete prototypes were fabricated and mounted at the rear corners of the hood, incorporated within a full-scale vehicle testbed at the SMARTT (Smart Material Advanced Research and Technology Transfer) lab at University of Michigan. Full operational cycle testing of a stationary vehicle in a laboratory setting confirms the ultrafast latch release, controlled lift profile, gravity lower to reposition the hood, and spring recompression via the ratchet engine successfully rearming the device for repeat cycles. While this is only a laboratory demonstration and extensive testing and development would be required for transition to a fielded product, this study does indicate that the SMArt Lift has promise as an alternative approach to pedestrian protection.

  14. Properties of laser alloyed surface layers on magnesium base alloys

    Energy Technology Data Exchange (ETDEWEB)

    Galun, R.; Weisheit, A.; Mordike, B.L. (Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. fuer Werkstoffkunde und Werkstofftechnik)

    1998-01-01

    The investigations have shown that laser surface alloying is a promising process to improve the wear and corrosion properties of magnesium base alloys without affecting the initial bulk properties like the low density. With an alloying element combination of aluminium and nickel the wear rate in the scratch test was reduced by 90% compared to untreated pure magnesium. Additionally the corrosion resistance was improved by laser alloying with this element combination. Because of distortion or crack formation in the case of large area treatments, the laser alloying should be limited to the treatment of smaller areas. In the near future this process could be an interesting alternative to surface coating or to a partially reinforcement with ceramic fibres or particles. (orig.)

  15. Development of Shape Memory Alloys- Challenges and Solutions

    Science.gov (United States)

    Benafan, Othmane

    2016-01-01

    Shape memory alloys (SMAs) are a unique class of multifunctional materials that have the ability to recover large deformations or generate high stresses in response to thermal, mechanical andor electromagnetic stimuli. These abilities have made them a viable option for actuation systems in aerospace, medical, and automotive applications, amongst others. However, despite many advantages and the fact that SMA actuators have been developed and used for many years, so far they have only found service in a limited range of applications. In order to expand their applications, further developments are needed to increase their reliability and stability and to address processing, testing and qualification needed for large-scale commercial application of SMA actuators. In this seminar, historical inhibitors of SMA applications and current research efforts by NASA Glenn Research Center and collaborators will be discussed. Relationships between fundamental physicalscientific understanding, and the direct transition to engineering and design of mechanisms using these novel materials will be highlighted. Examples will be presented related to targeted alloy development, microstructural control, and bulk-scale testing as a function of stresses, temperatures and harsh environments. The seminar will conclude with a summary of SMA applications under development and current advances.

  16. Boriding of binary Ni-Ti shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ucar, Nazim; Dogan, Sule [Suleyman Demirel Univ., Isparta (Turkey). Physics Dept.; Karakas, Mustafa Serdar [Cankaya Univ., Ankara (Turkey). Materials Science and Engineering Dept.; Calik, Adnan [Suleyman Demirel Univ., Isparta (Turkey). Manufacturing Engineering Dept.

    2016-07-01

    Boriding of binary Ni-Ti shape memory alloys was carried out in a solid medium at 1273 K for 2, 4, 6, and 8 h using the powder pack method with proprietary Ekabor-Ni powders. Characterization of the boride layer formed on the surface of alloys was done by optical microscopy and scanning electron microscopy. The presence of boride, silicide, and borosilicide phases in the boride layers was confirmed by X-ray diffraction analysis. The thickness and microhardness of the boride layers increased with increasing boriding time. Hardness profiles showed a rapid decrease in hardness moving from the boride layer to the main structure. The high hardness of the boride layer was attributed mainly to the formation of TiB{sub 2}. A parabolic relationship was observed between layer thickness and boriding time, and the growth rate constant for the boriding treatment was calculated as 0.62 x 10{sup -8} cm{sup 2}s{sup -1}.

  17. Damping performance of Cu-Zn-Al shape memory alloys in engineering structures

    Institute of Scientific and Technical Information of China (English)

    司乃潮; 孙克庆; 孙少纯; 刘海霞

    2004-01-01

    The stress strain curves of two CuZnAl shape memory alloys which have the martensitic transformation temperatures of 50 ℃ and -10 ℃ respectively, were measured by using electronic material tester after treated by different heat-treatment conditions. The results show that the area enclosed by hysteresis loop of the CuZnAl shape memory alloy in martensitic state is much larger than that of the alloy in austenitic state with super-elasticity at room temperature. Therefore, the former has better vibration attenuation effect. After being oil-quenched, waterquenched, and step-quenched, the CuZnAl alloy takes on more stable shape memory effect, better super-plasticity and superelasticity (pseudoelasticity). A CuZnAl shape memory alloy damper was designed, produced and installed to a 2-layer frame structure. In addition, the vibration experiments were made by dynamic data collecting analysis meter. The velocity of vibration attenuation of frame structure with CuZnAl shape memory alloy damper is much faster than that without it. And with the help of CuZnAl shape memory alloy damper, the attenuation period reduces to 1/10 of the original.

  18. Microstructure and Shape Memory Behavior of Ti-Nb Shape Memory Alloy Thin Film

    Science.gov (United States)

    Meng, X. L.; Sun, B.; Sun, J. Y.; Gao, Z. Y.; Cai, W.; Zhao, L. C.

    2017-06-01

    Ti-Nb shape memory alloy (SMA) thin film is a promising candidate applied as microactuator in biomedical field. In this study, the microstructure and shape memory behavior of Ti-Nb SMA thin films in different heat treatment conditions have been investigated. Fine ω phases embedded in the β phase matrix suppress the martensitic transformation of the films. As a result, the as-deposited and most of the annealed films consist of the β and α″ dual phases. The annealed Ti-Nb thin film shows excellent superelasticity effect when deformed above the reverse martensitic transformation temperature, that is 3.5% total recovery strain can be obtained when 4% pre-strain is loaded.

  19. Thermodynamic constitutive model for load-biased thermal cycling test of shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Young, Sung, E-mail: ysy@kut.ac.kr [Korea University of Technology and Education, Chonan (Korea, Republic of); Nam, Tae-Hyun, E-mail: tahynam@gnu.ac.kr [School of Materials Science and Engineering and ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of)

    2013-12-15

    Graphical abstract: - Highlights: • Thermodynamic calculation model for martensitic transformation of shape memory alloy was proposed. • Evolution of the self-accommodation was considered independently by a rate-dependent kinetic equation. • Finite element calculation was conducted for B2–B19′ transformation of Ti–44.5Ni–5Cu–0.5 V (at.%). • Three-dimensional numerical results predict the macroscopic strain under bias loading accurately. - Abstract: This paper presents a three-dimensional calculation model for martensitic phase transformation of shape memory alloy. Constitutive model based on thermodynamic theory was provided. The average behavior was accounted for by considering the volume fraction of each martensitic variant in the material. Evolution of the volume fraction of each variant was determined by a rate-dependent kinetic equation. We assumed that nucleation rate is faster for the self-accommodation than for the stress-induced variants. Three-dimensional finite element analysis was conducted and the results were compared with the experimental data of Ti–44.5Ni–5Cu–0.5 V (at.%) alloy under bias loading.

  20. On the mechanical properties of TiNb based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Y. [SIMAP-CNRS, Institut Polytechnique de Grenoble, BP 75, St. Martin d’Hères 38402 (France); Georgarakis, K. [WPI Advanced Institute for Materials Research, Tohoku University, Sendai (Japan); SIMAP-CNRS, Institut Polytechnique de Grenoble, BP 75, St. Martin d’Hères 38402 (France); Yokoyama, Y. [WPI Advanced Institute for Materials Research, Tohoku University, Sendai (Japan); Yavari, A.R., E-mail: euronano@minatec.inpg.fr [SIMAP-CNRS, Institut Polytechnique de Grenoble, BP 75, St. Martin d’Hères 38402 (France)

    2013-09-15

    Highlights: •Systematic study of compressive behaviors of TiNb based alloys in different states. •Comparison between X-ray diffraction results in reflection and transmission mode. •High melting temperature TiNb based alloys were fabricated by copper mold casting. •Textures of studied alloys are analyzed through synchrotron radiation data. -- Abstract: A series of TiNb(Sn) alloys were synthesized by copper mold suction casting and subjected to different heat treatments (furnace cooling or water quenching). The microstructure, thermal and mechanical properties of the as-cast and heat treated samples were investigated. For the Ti–8.34 at.% Nb alloy, the as-cast and water quenched samples possess martensitic α′′ phase at room temperature and compression tests of these samples show occurrence of shape memory effect. For β phase Ti–25.57 at.% Nb alloys, stress-induced martensitic transformation was found during compression in the as-cast and water quenched samples. For the ternary Ti–25.05 at.%Nb–2.04 at.%Sn alloy, conventional linear elastic behavior was observed. It is shown that the addition of Sn increases the stability of the β phase. The Young’s moduli of these alloys were also measured by ultrasonic measurements. Water-quenched Ti–25.57 at.%Nb alloy was found to exhibit the lowest Young’s modulus value. Sn addition has small impact on the Young’s moduli of the TiNb alloys.

  1. Grain size and temperature influence on the toughness of a CuAlBe shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Albuquerque, Victor Hugo C. de, E-mail: victor.albuquerque@fe.up.pt [Universidade Federal da Paraiba (UFPB), Departamento de Engenharia Mecanica (DEM), Laboratorio de Solidificacao Rapida LSR, Cidade Universitaria, S/N 58059-900 Joao Pessoa, PB (Brazil); Melo, Tadeu Antonio de A, E-mail: tadeu@lsr.ct.ufpb.br [Universidade Federal da Paraiba (UFPB), Departamento de Engenharia Mecanica (DEM), Laboratorio de Solidificacao Rapida LSR, Cidade Universitaria, S/N 58059-900 Joao Pessoa, PB (Brazil); Gomes, Rodinei M., E-mail: gomes@lsr.ct.ufpb.br [Universidade Federal da Paraiba (UFPB), Departamento de Engenharia Mecanica (DEM), Laboratorio de Solidificacao Rapida LSR, Cidade Universitaria, S/N 58059-900 Joao Pessoa, PB (Brazil); Lima, Severino Jackson G. de, E-mail: jackson@lsr.ct.ufpb.br [Universidade Federal da Paraiba (UFPB), Departamento de Engenharia Mecanica (DEM), Laboratorio de Solidificacao Rapida LSR, Cidade Universitaria, S/N 58059-900 Joao Pessoa, PB (Brazil); Tavares, Joao Manuel R.S., E-mail: tavares@fe.up.pt [Faculdade de Engenharia da Universidade do Porto (FEUP), Departamento de Engenharia Mecanica (DEMec)/Instituto de Engenharia Mecanica e Gestao Industrial INEGI, Rua Dr. Roberto Frias, S/N 4200-465 Porto (Portugal)

    2010-11-25

    Research highlights: {yields} This work evaluated the capacity of a CuAlBe alloy to absorb energy until rupture. {yields} The V-notch Charpy test was adopted at -150, -100, -50, 0, 50, 100 and 150 deg. C. {yields} Charpy tests were complemented by DSC, DSC with optical microscope and by SEM. {yields} First work to analyze the toughness of a CuAlBe alloy based on the Charpy test. {yields} The results are of relevant value to enhance the understanding of the CuAlBe alloy. - Abstract: This work is a study of the influence of grain size and temperature on the toughness of CuAlBe shape memory alloys with (CuAlBeNbNi) and without NbNi (CuAlBe) grain refiner elements. The toughness analysis was based on the V-notch Charpy impact test under temperatures of -150, -100, -50, 0, 50, 100 and 150 deg. C. A statistical analysis of the results led to the conclusion that the toughness of both alloys was influenced by temperature and grain size. The CuAlBeNbNi alloy absorbed higher impact energy than the CuAlBe alloy showing that the refining elements improved the toughness of the alloy. To confirm and complement these findings, the fracture surfaces were evaluated by stereomicroscopy. Smooth homogeneous surfaces and rough heterogonous surfaces were detected for the CuAlBeNbNi and CuAlBe alloys, respectively. Predominately brittle zones were confirmed by scanning electron microscopy in both alloys. Furthermore, to determine the phase transformation temperatures and the associated microstructures, the alloys were assessed by conventional differential scanning calorimetry (DSC) and DSC with optical microscopy.

  2. Processing of Ni30Pt20Ti50 High-Temperature Shape-Memory Alloy Into Thin Rod Demonstrated

    Science.gov (United States)

    Noebe, Ronald D.; Draper, Susan L.; Biles, Tiffany A.; Leonhardt, Todd

    2005-01-01

    High-temperature shape-memory alloys (HTSMAs) based on nickel-titanium (NiTi) with significant ternary additions of palladium (Pd), platinum (Pt), gold (Au), or hafnium (Hf) have been identified as potential high-temperature actuator materials for use up to 500 C. These materials provide an enabling technology for the development of "smart structures" used to control the noise, emissions, or efficiency of gas turbine engines. The demand for these high-temperature versions of conventional shape-memory alloys also has been growing in the automotive, process control, and energy industries. However these materials, including the NiPtTi alloys being developed at the NASA Glenn Research Center, will never find widespread acceptance unless they can be readily processed into useable forms.

  3. Vacuum Arc Melting Processes for Biomedical Ni-Ti Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Tsai De-Chang

    2015-01-01

    Full Text Available This study primarily involved using a vacuum arc remelting (VAR process to prepare a nitinol shape-memory alloy with distinct ratios of alloy components (nitinol: 54.5 wt% to 57 wt%. An advantage of using the VAR process is the adoption of a water-cooled copper crucible, which effectively prevents crucible pollution and impurity infiltration. Optimising the melting production process enables control of the alloy component and facilitates a uniformly mixed compound during subsequent processing. This study involved purifying nickel and titanium and examining the characteristics of nitinol alloy after alloy melt, including its microstructure, mechanical properties, phase transition temperature, and chemical components.

  4. Effect of grain size on superelasticity in Fe-Mn-Al-Ni shape memory alloy wire

    Directory of Open Access Journals (Sweden)

    T. Omori

    2013-09-01

    Full Text Available Effects of grain size on superelastic properties in Fe-34Mn-15Al-7.5Ni alloy wires with a ⟨110⟩ fiber-texture were investigated by cyclic tensile tests. It was confirmed that the critical stress for induced martensitic transformation and the superelastic strain are functions of relative grain size d/D (d: mean grain diameter, D: wire diameter, and that the critical stress is proportional to (1–d/D2 as well as in Cu-based shape memory alloys. A large superelastic strain of about 5% was obtained in the specimen with a large relative grain size over d/D = 1.

  5. Anodic Fabrication of Ti-Ni-O Nanotube Arrays on Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Qiang Liu

    2014-04-01

    Full Text Available Surface modification with oxide nanostructures is one of the efficient ways to improve physical or biomedical properties of shape memory alloys. This work reports a fabrication of highly ordered Ti-Ni-O nanotube arrays on Ti-Ni alloy substrates through pulse anodization in glycerol-based electrolytes. The effects of anodization parameters and the annealing process on the microstructures and surface morphology of Ti-Ni-O were studied using scanning electron microscope and Raman spectroscopy. The electrolyte type greatly affected the formation of nanotube arrays. A formation of anatase phase was found with the Ti-Ni-O nanotube arrays annealed at 450 °C. The oxide nanotubes could be crystallized to rutile phase after annealing treatment at 650 °C. The Ti-Ni-O nanotube arrays demonstrated an excellent thermal stability by keeping their nanotubular structures up to 650 °C.

  6. High Work Output Ni-Ti-Pt High Temperature Shape Memory Alloys and Associated Processing Methods

    Science.gov (United States)

    Noebe, Ronald D. (Inventor); Draper, Susan L. (Inventor); Nathal, Michael V. (Inventor); Garg, Anita (Inventor)

    2009-01-01

    According to the invention, compositions of Ni-Ti-Pt high temperature, high force, shape memory alloys are disclosed that have transition temperatures above 100 C.; have narrow hysteresis; and produce a high specific work output.

  7. Near Net Shape Fabrication Technology for Shape Memory Alloy Components Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This STTR Phase I effort proposes to develop an innovative, affordable processing route for larger-sized shape memory alloy (SMA) components. Despite significant...

  8. Medical application of NiTi shape memory alloy in China

    Energy Technology Data Exchange (ETDEWEB)

    Chu, Y. [Nonferrous Metals Society of China (NFSOC), Beijing, BJ (China); Dai, K. [Ninth People' s Hospital, Shanghai, SH (China); Zhu, M.; Mi, X. [General Research Inst. for Nonferrous Metals, Beijing, BJ (China)

    2000-07-01

    In the present paper, a general review of clinical application of NiTi shape memory alloy in bone implantation, orthodontics and interventional treatment in China is given with some of typical topics introduced in detail. (orig.)

  9. An analytical model for shape memory alloy fiber-reinforced composite thin-walled beam undergoing large deflection

    Directory of Open Access Journals (Sweden)

    Yongsheng Ren

    2015-03-01

    Full Text Available The structural model of the thin-walled laminated beams with integral shape memory alloy active fibers and accounting for geometrically nonlinear is presented in this article. The structural modeling is split into two parts: a two-dimensional analysis over the cross section and a geometrically nonlinear analysis of a beam along the beam span. The variational asymptotic method is used to formulate the force–deformation relationship equations taking into account the presence of active shape memory alloy fibers distributed along the cross section of the beam. The geometrically nonlinear governing equations are derived using variational principle and based on the von Kármán-type nonlinear strain–displacement relations. The equations are then solved using Galerkin’s method and an incremental Newton–Raphson method. The validation for the proposed model has been carried out by comparison of the present results with those available in the literature. The results show that significant extension, bending, and twisting coupled nonlinear deflections occur during the phase transformation due to shape memory alloy actuation. The effects of the volume fraction of the shape memory alloy fiber and ply angle are also addressed.

  10. An investigation of shape memory alloys as actuating elements in aerospace morphing applications

    DEFF Research Database (Denmark)

    Kappatos, Vasileios; Karagiannis, Dimitrios; Stamatelos, Dimtrios

    2017-01-01

    Two innovative actuating concepts for aerospace morphing applications, based on Shape Memory Alloys (SMAs), are proposed. The first concept investigates a composite plate incorporating embedded SMA wires. A Nonlinear Auto Regressive with eXogenous excitation (NARX) model is proposed for controlling...... a single-cycle/multi-cycle loading conditions of the SMA wires. The second actuating concept studies a novel rib configuration, which incorporates a compliant mechanism for enabling aerofoil's Leading Edge (LE) morphing. Different rib-compliant mechanism concepts are designed and analysed. The most...

  11. Seismic Response Control of Offshore Platform Structures with Shape Memory Alloy Dampers

    Institute of Scientific and Technical Information of China (English)

    LI Hong-nan; HE Xiao-yu; HUO Lin-sheng

    2005-01-01

    In this study, the seismic response control of offshore platform structures with Shape Memory Alloy (SMA) dampers is investigated. A new SMA damper and its restoring force model are introduced for the calculation of seismic response reduction. Based on an actual platform structure and its mechanical model, the parameters which may affect the rate of shock absorption are analyzed, such as the number, position and characteristics of the SMA dampers andthe condition of the site where the platform is located. The results show that the SMA damper is an effective control device for offshore platforms and satisfactory control can be achieved by proper selection of the parameters.

  12. Magnetic Shape Memory Alloys as smart materials for micro-positioning devices

    Directory of Open Access Journals (Sweden)

    A. Hubert

    2012-10-01

    Full Text Available In the field of microrobotics, actuators based on smart materials are predominant because of very good precision, integration capabilities and high compactness. This paper presents the main characteristics of Magnetic Shape Memory Alloys as new candidates for the design of micromechatronic devices. The thermo-magneto-mechanical energy conversion process is first presented followed by the adequate modeling procedure required to design actuators. Finally, some actuators prototypes realized at the Femto-ST institute are presented, including a push-pull bidirectional actuator. Some results on the control and performances of these devices conclude the paper.

  13. Fe-Ni-Si基奥氏体时效合金的马氏体相变和形状记忆效应%Martensitic transformation and shape memory effect in ausaged Fe-Ni-Si-based alloys

    Institute of Scientific and Technical Information of China (English)

    田中优树

    2005-01-01

    It is well known that the morphologies of the α martensite formed from the γ phase in ferrous alloys are classified into five types of lath, butterfly, (225)A type plate,lenticular and thin-plate. Among those α martensites, onlythe thinplate martensite, which is characterized by containing a high density of transformation twins, has a potential of exhibiting a perfect shape memory (SM) effect.Recently the present authors found in Fe-Ni-Si alloys that the thin-plate martensite is formed by the introduction of fine and coherent γ-(Ni,Fe)3Si particles with a L12 ordered structure in the austenite matrix due to ausaging. In the present study, the SM properties of the ausaged Fe-Ni-Si alloys with the thin-plate martensite are investigated by a conventional bending-test. The effects of the addition of Co to the Fe-Ni-Si alloys on the martensitic transformation and the SM properties are also investigated. It is shown that while the ausaged Fe-Ni-Si ternary alloys exhibit an imperfect SM effect due to reverse transformation from stress-induced thin-plate martensite to austenite, the SM properties are improved by the addition of Co. An almost perfect SM effect is confirmed in the Fe-Ni-Si-Co alloys by heating to 1 100 ℃ after deformation at -196 ℃.

  14. Stress Relaxation Of Superelastic Shape Memory Alloy Under Bending And Torsional Load

    Directory of Open Access Journals (Sweden)

    Sakib Tanvir

    2015-08-01

    Full Text Available Stress Relaxation of Superelastic Shape memory NiTi Alloy under bending and torsion is uncommon in literature. Therefore experimental set up has been devised and test results are obtained for superelastic SMA.Unlike the other common engineering materials superelastic SMA it gives dramatic reduction in stress. In this paper therefore results of stress relaxation of superelastic shape memory alloy under bending and torsion are presented graphically and interpreted in terms of stress induced martensitic transformation.

  15. Shape memory alloy seals for geothermal applications. Final report. Report ESG-82-14

    Energy Technology Data Exchange (ETDEWEB)

    Friske, Warren H.; Schwartzbart, Harry

    1982-07-30

    A novel temperature-actuated seal for geothermal applications is under development. This program uses the shape memory property of nickel-titanium (Nitinol) alloys to achieve an improved seal in geothermal downhole pumps. Nitinol flange face seals and pump shaft seals have been designed, fabricated, and tested. It has been demonstrated that the shape memory effect of Nitinol alloys can be utilized to activate and maintain a leaktight seal in geothermal environments.

  16. Phase diagram kinetics for shape memory alloys: a robust finite element implementation

    Science.gov (United States)

    Gao, Xiujie; Qiao, Rui; Brinson, L. Catherine

    2007-12-01

    A physically based one-dimensional shape memory alloy (SMA) model is implemented into the finite element software ABAQUS via a user interface. Linearization of the SMA constitutive law together with complete transformation kinetics is performed and tabulated for implementation. Robust rules for transformation zones of the phase diagram are implemented and a new strategy for overlapping transformation zones is developed. The iteration algorithm, switching point updates and solution strategies are developed and are presented in detail. The code is validated via baseline simulations including the shape memory effect and pseudoelasticity and then further tested with complex loading paths. A hybrid composite with self-healing function is then simulated using the developed code. The example demonstrates the usefulness of the methods for the design and simulation of materials or structures actuated by SMA wires or ribbons.

  17. Thermomechanical response of NiTi shape-memory nanoprecipitates in TiV alloys

    Science.gov (United States)

    Maisel, S. B.; Ko, W.-S.; Zhang, J.-L.; Grabowski, B.; Neugebauer, J.

    2017-08-01

    We study the properties of NiTi shape-memory nanoparticles coherently embedded in TiV matrices using three-dimensional atomistic simulations based on the modified embedded-atom method. To this end, we develop and present a suitable NiTiV potential for our simulations. Employing this potential, we identify the conditions under which the martensitic phase transformation of such a nanoparticle is triggered—specifically, how these conditions can be tuned by modifying the size of the particle, the composition of the surrounding matrix, or the temperature and strain state of the system. Using these insights, we establish how the transformation temperature of such particles can be influenced and discuss the practical implications in the context of shape-memory strengthened alloys.

  18. Cobalt-Base Alloy Gun Barrel Study

    Science.gov (United States)

    2014-07-01

    are presented in Section 5. 2. Materials and methods The composition of the cobalt -base alloy (CBA) is presented in Table 1. The production of this... Cobalt -Base Alloy Gun Barrel Study by William S. de Rosset and Jonathan S. Montgomery ARL-RP-0491 July 2014 A reprint...21005-5069 ARL-RP-0491 July 2014 Cobalt -Base Alloy Gun Barrel Study William S. de Rosset and Jonathan S. Montgomery Weapons and Materials

  19. The Effect of Stress Ageing on the Properties of Shape Memory Alloys

    OpenAIRE

    A. Michael

    1995-01-01

    The performance characteristics of shape memory alloys operating in an overtemperature shut-off valve at a temperature of 95°C for up to 2000 hours are presented. Alloys of NiTi, Cu-Al-Ni and Cu-Zn-Al have been characterised under these ageing conditions. The effect of altering the processing parameters, viz solution treatment temperature, quenching technique and training procedure were examined. All alloys show degradation of the memory behaviour but results are presented which demonstrate t...

  20. Design optimization of shape memory alloy active structures using the R-phase transformation

    NARCIS (Netherlands)

    Langelaar, M.; Van Keulen, F.

    2007-01-01

    This article illustrates the opportunities that combining computational modeling and systematic design optimization techniques offer to facilitate the design process of shape memory alloy (SMA) structures. Focus is on shape memory behavior due to the R-phase transformation in Ni-Ti, for which a dedi

  1. Texture development and anisotropic behaviour in a Ti-45Ni-5Cu (AT.%) shape memory alloy

    NARCIS (Netherlands)

    Zhao, Lie

    1997-01-01

    The objective of this work was to determine the relationship between texture development and anisotropy of shape memory properties. A commercial Ti-45Ni-5Cu (at.%) shape memory alloy was selected. Textures were developed by controlling rolling parameters, such as rolling temperature, intermediate an

  2. Alloying effect on K-shell fluorescence parameters of porous NiTi shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Cengiz, E., E-mail: erhan_cengiz@ktu.edu.tr [Karadeniz Technical University, Science Faculty, Department of Physics, 61080 Trabzon (Turkey); Ozkendir, O.M. [Mersin University, Tarsus Faculty of Technology, Tarsus (Turkey); Kaya, M. [Adiyaman University, Department of Material Science Engineering, 02040 Adiyaman (Turkey); Tirasoglu, E. [Karadeniz Technical University, Science Faculty, Department of Physics, 61080 Trabzon (Turkey); Karahan, I.H. [Mustafa Kemal University, Faculty of Arts and Sciences, Department of Physics, Antakya, Hatay (Turkey); Kimura, S.; Hajiri, T. [UVSOR Facility, Institute for Molecular Science, Okazaki 444-8585 (Japan)

    2014-01-01

    Highlights: • The K{sub α,β} shell production cross-sections and K{sub β}/K{sub α} intensity ratios of porous NiTi SMAs were determined by ED-XRF. • To analyze the changes in the structures due to the preheating and solution heat treatment processes, XRD and XPS measurements were also performed. • The deviations between the experimental and theoretical were interpreted to charge transfer phenomena. - Abstract: The K{sub α,β} shell production cross-sections and K{sub β}/K{sub α} intensity ratios of porous Ni −49 at% Ti shape memory alloys were determined using energy dispersive X-ray fluorescence (EDXRF) technique. Also, the alloying effect on the K shell fluorescence parameters was investigated. The samples were excited by 59.5 keV γ-rays from an {sup 241}Am annular radioactive source. The K X-rays emitted by the samples were counted by an Ultra-LEGe detector with a resolution of 150 eV at 5.9 keV. The structure analyses of the samples were also made using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The deviations between the present results and theoretical values, calculated for pure Ti and Ni, were attributed to charge transfer phenomena and/or rearrangement of valance shell electrons and porosity.

  3. Memory-Based Shallow Parsing

    NARCIS (Netherlands)

    Tjong Kim Sang, E.F.

    2002-01-01

    We present memory-based learning approaches to shallow parsing and apply these to five tasks: base noun phrase identification, arbitrary base phrase recognition, clause detection, noun phrase parsing and full parsing. We use feature selection techniques and system combination methods for improving t

  4. Memory-Based Shallow Parsing

    NARCIS (Netherlands)

    Tjong Kim Sang, E.F.

    2002-01-01

    We present memory-based learning approaches to shallow parsing and apply these to five tasks: base noun phrase identification, arbitrary base phrase recognition, clause detection, noun phrase parsing and full parsing. We use feature selection techniques and system combination methods for improving

  5. Potential High-Temperature Shape-Memory Alloys Identified in the Ti(Ni,Pt) System

    Science.gov (United States)

    Noebe, Ronald D.; Biles, Tiffany A.; Garg, Anita; Nathal, Michael V.

    2004-01-01

    "Shape memory" is a unique property of certain alloys that, when deformed (within certain strain limits) at low temperatures, will remember and recover to their original predeformed shape upon heating. It occurs when an alloy is deformed in the low-temperature martensitic phase and is then heated above its transformation temperature back to an austenitic state. As the material passes through this solid-state phase transformation on heating, it also recovers its original shape. This behavior is widely exploited, near room temperature, in commercially available NiTi alloys for connectors, couplings, valves, actuators, stents, and other medical and dental devices. In addition, there are limitless applications in the aerospace, automotive, chemical processing, and many other industries for materials that exhibit this type of shape-memory behavior at higher temperatures. But for high temperatures, there are currently no commercial shape-memory alloys. Although there are significant challenges to the development of high-temperature shape-memory alloys, at the NASA Glenn Research Center we have identified a series of alloy compositions in the Ti-Ni-Pt system that show great promise as potential high-temperature shape-memory materials.

  6. Thermodynamic assessment of the stabilization effect in deformed shape memory alloy martensite

    Energy Technology Data Exchange (ETDEWEB)

    Kato, Hiroyuki, E-mail: hkato@eng.hokudai.ac.jp [Division of Mechanical and Space Engineering, Faculty of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Yasuda, Yohei, E-mail: yasuda-yoh@mech-me.eng.hokudai.ac.jp [Division of Mechanical and Space Engineering, Faculty of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Sasaki, Kazuaki, E-mail: kazki@eng.hokudai.ac.jp [Division of Mechanical and Space Engineering, Faculty of Engineering, Hokkaido University, Sapporo 060-8628 (Japan)

    2011-06-15

    When a martensitic shape memory alloy is deformed, the reverse transformation occurs at higher temperature than that of undeformed martensite. This is a typical case of the stabilization effect of martensite that is commonly observed in shape memory alloys. Regarding previous results measured by electric resistance and/or dilatometoric methods in NiTi and CuAlNi shape memory alloys, this study has performed calorimetric measurement in these alloys in order to re-examine the stabilization effect in terms of thermodynamics. Experimental evidence for appreciable changes in the reverse transformation temperature due to variant change of the martensite is presented. The elastic energy stored in the deformed martensite and the irreversible energy dissipated during the reverse transformation are estimated from the transformation temperatures, the stress-strain curves of the martensite and the latent heat of transformation. The temperatures of the reverse martensitic transformation have been related to these energies in explicit form.

  7. Shape memory alloy wire for self-sensing servo actuation

    Science.gov (United States)

    Josephine Selvarani Ruth, D.; Dhanalakshmi, K.

    2017-01-01

    This paper reports on the development of a straightforward approach to realise self-sensing shape memory alloy (SMA) wire actuated control. A differential electrical resistance measurement circuit (the sensorless signal conditioning (SSC) circuit) is designed; this sensing signal is directly used as the feedback for control. Antagonistic SMA wire actuators designed for servo actuation is realized in self-sensing actuation (SSA) mode for direct control with the differential electrical resistance feedback. The self-sensing scheme is established on a 1-DOF manipulator with the discrete time sliding mode controls which demonstrates good control performance, whatever be the disturbance and loading conditions. The uniqueness of this work is the design of the generic electronic SSC circuit for SMA actuated system, for measurement and control. With a concern to the implementation of self-sensing technique in SMA, this scheme retains the systematic control architecture by using the sensing signal (self-sensed, electrical resistance corresponding to the system position) for feedback, without requiring any processing as that of the methods adopted and reported previously for SSA techniques of SMA.

  8. Transformation reversibility in Fe-Mn-Si shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Tsuzaki, K. [Kyoto Univ. (Japan). Dept. of Mater. Sci. and Eng.; Natsume, Y. [Kyoto Univ. (Japan). Dept. of Mater. Sci. and Eng.; Maki, T. [Kyoto Univ. (Japan). Dept. of Mater. Sci. and Eng.

    1995-12-01

    The change of the surface relief associated with stress-induced epsilon martensite before and after the reverse transformation in an Fe-33%Mn-6%Si alloy (Ms=264K) has been investigated. The permanent strain of a 2.7% tensile-strained specimen was 1.1% after the reverse transformation. In this specimen, a large part of surface relief still remained after heating to 623K (above Af). When five training cycles of 2.5% straining at room temperature and heating at 623K were applied, the permanent strain became negligible and the surface relief vanished well. TEM observations showed that usual permament slip deformation hardly occurred in the interior of an austenite grain in a 3.8% tensile-strained specimen where the permanent strain after the reversion was 2%. These results indicate that the permanent strain in the shape memory behavior is mainly attributed to the lack of transformation reversibility, i.e., the lack of reversible movement of Shockley partial dislocations. The conditions for the reversibility were discussed and the importance of the back stress formed by the forward transformation was pointed out. The effects of traning were also briefly discussed. (orig.).

  9. Bioinspired Soft Actuation System Using Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Matteo Cianchetti

    2014-07-01

    Full Text Available Soft robotics requires technologies that are capable of generating forces even though the bodies are composed of very light, flexible and soft elements. A soft actuation mechanism was developed in this work, taking inspiration from the arm of the Octopus vulgaris, specifically from the muscular hydrostat which represents its constitutive muscular structure. On the basis of the authors’ previous works on shape memory alloy (SMA springs used as soft actuators, a specific arrangement of such SMA springs is presented, which is combined with a flexible braided sleeve featuring a conical shape and a motor-driven cable. This robot arm is able to perform tasks in water such as grasping, multi-bending gestures, shortening and elongation along its longitudinal axis. The whole structure of the arm is described in detail and experimental results on workspace, bending and grasping capabilities and generated forces are presented. Moreover, this paper demonstrates that it is possible to realize a self-contained octopus-like robotic arm with no rigid parts, highly adaptable and suitable to be mounted on underwater vehicles. Its softness allows interaction with all types of objects with very low risks of damage and limited safety issues, while at the same time producing relatively high forces when necessary.

  10. Modiolus-Hugging Intracochlear Electrode Array with Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Kyou Sik Min

    2013-01-01

    Full Text Available In the cochlear implant system, the distance between spiral ganglia and the electrodes within the volume of the scala tympani cavity significantly affects the efficiency of the electrical stimulation in terms of the threshold current level and spatial selectivity. Because the spiral ganglia are situated inside the modiolus, the central axis of the cochlea, it is desirable that the electrode array hugs the modiolus to minimize the distance between the electrodes and the ganglia. In the present study, we propose a shape-memory-alloy-(SMA- embedded intracochlear electrode which gives a straight electrode a curved modiolus-hugging shape using the restoration force of the SMA as triggered by resistive heating after insertion into the cochlea. An eight-channel ball-type electrode array is fabricated with an embedded titanium-nickel SMA backbone wire. It is demonstrated that the electrode array changes its shape in a transparent plastic human cochlear model. To verify the safe insertion of the electrode array into the human cochlea, the contact pressures during insertion at the electrode tip and the contact pressures over the electrode length after insertion were calculated using a 3D finite element analysis. The results indicate that the SMA-embedded electrode is functionally and mechanically feasible for clinical applications.

  11. Modiolus-hugging intracochlear electrode array with shape memory alloy.

    Science.gov (United States)

    Min, Kyou Sik; Jun, Sang Beom; Lim, Yoon Seob; Park, Se-Ik; Kim, Sung June

    2013-01-01

    In the cochlear implant system, the distance between spiral ganglia and the electrodes within the volume of the scala tympani cavity significantly affects the efficiency of the electrical stimulation in terms of the threshold current level and spatial selectivity. Because the spiral ganglia are situated inside the modiolus, the central axis of the cochlea, it is desirable that the electrode array hugs the modiolus to minimize the distance between the electrodes and the ganglia. In the present study, we propose a shape-memory-alloy-(SMA-) embedded intracochlear electrode which gives a straight electrode a curved modiolus-hugging shape using the restoration force of the SMA as triggered by resistive heating after insertion into the cochlea. An eight-channel ball-type electrode array is fabricated with an embedded titanium-nickel SMA backbone wire. It is demonstrated that the electrode array changes its shape in a transparent plastic human cochlear model. To verify the safe insertion of the electrode array into the human cochlea, the contact pressures during insertion at the electrode tip and the contact pressures over the electrode length after insertion were calculated using a 3D finite element analysis. The results indicate that the SMA-embedded electrode is functionally and mechanically feasible for clinical applications.

  12. Modiolus-Hugging Intracochlear Electrode Array with Shape Memory Alloy

    Science.gov (United States)

    Min, Kyou Sik; Lim, Yoon Seob; Park, Se-Ik; Kim, Sung June

    2013-01-01

    In the cochlear implant system, the distance between spiral ganglia and the electrodes within the volume of the scala tympani cavity significantly affects the efficiency of the electrical stimulation in terms of the threshold current level and spatial selectivity. Because the spiral ganglia are situated inside the modiolus, the central axis of the cochlea, it is desirable that the electrode array hugs the modiolus to minimize the distance between the electrodes and the ganglia. In the present study, we propose a shape-memory-alloy-(SMA-) embedded intracochlear electrode which gives a straight electrode a curved modiolus-hugging shape using the restoration force of the SMA as triggered by resistive heating after insertion into the cochlea. An eight-channel ball-type electrode array is fabricated with an embedded titanium-nickel SMA backbone wire. It is demonstrated that the electrode array changes its shape in a transparent plastic human cochlear model. To verify the safe insertion of the electrode array into the human cochlea, the contact pressures during insertion at the electrode tip and the contact pressures over the electrode length after insertion were calculated using a 3D finite element analysis. The results indicate that the SMA-embedded electrode is functionally and mechanically feasible for clinical applications. PMID:23762181

  13. MOSFET Switching Circuit Protects Shape Memory Alloy Actuators

    Science.gov (United States)

    Gummin, Mark A.

    2011-01-01

    A small-footprint, full surface-mount-component printed circuit board employs MOSFET (metal-oxide-semiconductor field-effect transistor) power switches to switch high currents from any input power supply from 3 to 30 V. High-force shape memory alloy (SMA) actuators generally require high current (up to 9 A at 28 V) to actuate. SMA wires (the driving element of the actuators) can be quickly overheated if power is not removed at the end of stroke, which can damage the wires. The new analog driver prevents overheating of the SMA wires in an actuator by momentarily removing power when the end limit switch is closed, thereby allowing complex control schemes to be adopted without concern for overheating. Either an integral pushbutton or microprocessor-controlled gate or control line inputs switch current to the actuator until the end switch line goes from logic high to logic low state. Power is then momentarily removed (switched off by the MOSFET). The analog driver is suited to use with nearly any SMA actuator.

  14. Pseudo-creep in Shape Memory Alloy Wires and Sheets

    Science.gov (United States)

    Russalian, V. R.; Bhattacharyya, A.

    2017-10-01

    Interruption of loading during reorientation and isothermal pseudoelasticity in shape memory alloys with a strain arrest ( i.e., holding strain constant) results in a time-dependent evolution in stress or with a stress arrest ( i.e., holding stress constant) results in a time-dependent evolution in strain. This phenomenon, which we term as pseudo-creep, is similar to what was reported in the literature three decades ago for some traditional metallic materials undergoing plastic deformation. In a previous communication, we reported strain arrest of isothermal pseudoelastic loading, isothermal pseudoelastic unloading, and reorientation in NiTi wires as well as a rate-independent phase diagram. In this paper, we provide experimental results of the pseudo-creep phenomenon during stress arrest of isothermal pseudoelasticity and reorientation in NiTi wires as well as strain arrest of isothermal pseudoelasticity and reorientation in NiTi sheets. Stress arrest in NiTi wires accompanied by strain accumulation or recovery is studied using the technique of multi-video extensometry. The experimental results were used to estimate the amount of mechanical energy needed to evolve the wire from one microstructural state to another during isothermal pseudoelastic deformation and the difference in energies between the initial and the final rest state between which the aforementioned evolution has occurred.

  15. Experimental characterization of shape memory alloy actuator cables

    Science.gov (United States)

    Biggs, Daniel B.; Shaw, John A.

    2016-04-01

    Wire rope (or cables) are a fundamental structural element in many engineering applications. Recently, there has been growing interest in stranding NiTi wires into cables to scale up the adaptive properties of NiTi tension elements and to make use of the desirable properties of wire rope. Exploratory experiments were performed to study the actuation behavior of two NiTi shape memory alloy cables and straight monofilament wire of the same material. The specimens were held under various dead loads ranging from 50 MPa to 400 MPa and thermally cycled 25 times from 140°C to 5°C at a rate of 12°C/min. Performance metrics of actuation stroke, residual strain, and work output were measured and compared between specimen types. The 7x7 cable exhibited similar actuation to the single straight wire, but with slightly longer stroke and marginally more shakedown, while maintaining equivalent specific work output. This leads to the conclusion that the 7x7 cable effectively scaled up the adaptive properties the straight wire. Under loads below 150 MPa, the 1x27 cable had up to double the actuation stroke and work output, but exhibited larger shakedown and poorer performance when loaded higher.

  16. Microstructure and thermal expansion properties of invar-type Cu-Zn-Al shape memory alloys

    Science.gov (United States)

    Wang, J. J.; Omori, T.; Sutou, Y.; Kainuma, R.; Ishida, K.

    2004-10-01

    The effects of grain size, volume fraction of the α (fcc) phase in the β (bcc) matrix, and thermal stability on low thermal expansion (LTE) properties of Cu-Zn-Al shape memory (SM) alloys induced by cold rolling were investigated by dilatometry, optical microscopy, differential scanning calorimetry, and electrical conductivity measurements. The alloys with the larger grains showed a superior two-way memory (TWM) effect, wider LTE temperature intervals with excellent thermal stability under 80°C. The α+β two-phase alloys also exhibited a good combination of cold workability and LTE properties. These results suggest that the Cu-Zn-Al alloys with high electrical conductivity of about 20% International Annealed Copper Standard (%IACS) have high potential as a new class of Invar alloys that can be applied in various fields.

  17. Relationship between mechanical property and microstructure of NiTi shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    LIU; Mei-rong; GAO; Bao-dong; FENG; Zhao-wei; WANG; Jiang-bo

    2005-01-01

    The relationship between mechanical property and microstructure of NiTi shape memory alloy has been studied. It was founded that with increasing prestrain the memory recovery rate decreased, but the recovery stress and the recovery strain increased first and then decreased. The recovery stress and the recovery strain reached maximum at about 11% prestrain. The TEM(Transmission Electron Microscope) results of the alloy indicated that the microstructures with different prestrain of the alloy had obvious characters. At 9% prestrain, the martensite anamorphosis of the alloy still presented self-cooperation configuration, and some martensites have become thick obvi ously because of tropism. When the prestrain was 11%, the martensite anamorphosis has become completely thick and tropism became consistent. As the prestrain increased to 13%, the microstructures of the alloy have become disordered, the tropism became inconsistent and the interface became blurry.

  18. Potential High-Temperature Shape-Memory-Alloy Actuator Material Identified

    Science.gov (United States)

    Noebe, Ronald D.; Gaydosh, Darrell J.; Biles, Tiffany A.; Garg, Anita

    2005-01-01

    Shape-memory alloys are unique "smart materials" that can be used in a wide variety of adaptive or "intelligent" components. Because of a martensitic solid-state phase transformation in these materials, they can display rather unusual mechanical properties including shape-memory behavior. This phenomenon occurs when the material is deformed at low temperatures (below the martensite finish temperature, Mf) and then heated through the martensite-to-austenite phase transformation. As the material is heated to the austenite finish temperature Af, it is able to recover its predeformed shape. If a bias is applied to the material as it tries to recover its original shape, work can be extracted from the shape-memory alloy as it transforms. Therefore, shape-memory alloys are being considered for compact solid-state actuation devices to replace hydraulic, pneumatic, or motor-driven systems.

  19. Shape memory behavior of single and polycrystalline nickel rich nickel titanium alloys

    Science.gov (United States)

    Kaya, Irfan

    NiTi is the most commonly used shape memory alloy (SMA) and has been widely used for bio-medical, electrical and mechanical applications. Nickel rich NiTi shape memory alloys are coming into prominence due to their distinct superelasticity and shape memory properties as compared to near equi-atomic NiTi shape memory alloys. Besides, their lower density and higher work output than steels makes these alloys an excellent candidate for aerospace and automotive industry. Shape memory properties and phase transformation behavior of high Ni-rich Ni54Ti46 (at.%) polycrystals and Ni-rich Ni 51Ti49 (at.%) single-crystals are determined. Their properties are sensitive to heat treatments that affect the phase transformation behavior of these alloys. Phase transformation properties and microstructure were investigated in aged Ni54Ti46 alloys with differential scanning calorimetry (DSC) and transmission electron microscopy (TEM) to reveal the precipitation characteristics and R-phase formation. It was found that Ni54Ti46 has the ability to exhibit perfect superelasticity under high stress levels (~2 GPa) with 4% total strain after 550°C-3h aging. Stress independent R-phase transformation was found to be responsible for the change in shape memory behavior with stress. The shape memory responses of [001], [011] and [111] oriented Ni 51Ti49 single-crystals alloy were reported under compression to reveal the orientation dependence of their shape memory behavior. It has been found that transformation strain, temperatures and hysteresis, Classius-Clapeyron slopes, critical stress for plastic deformation are highly orientation dependent. The effects of precipitation formation and compressive loading at selected temperatures on the two-way shape memory effect (TWSME) properties of a [111]- oriented Ni51Ti49 shape memory alloy were revealed. Additionally, aligned Ni4Ti3 precipitates were formed in a single crystal of Ni51Ti49 alloy by aging under applied compression stress along the

  20. Bulk amorphous Mg-based alloys

    DEFF Research Database (Denmark)

    Pryds, Nini

    2004-01-01

    The present paper describes the preparation and properties of bulk amorphous quarternary Mg-based alloys and the influence of additional elements on the ability of the alloy to form bulk amorphous. The main goal is to find a Mg-based alloy system which shows both high strength to weight ratio...... and a low glass transition temperature. The alloys were prepared by using a relatively simple technique, i.e. rapid cooling of the melt in a copper wedge mould. The essential structural changes that are achieved by going from the amorphous to the crystalline state through the supercooled liquid state...... are discussed in this paper. On the basis of these measurements phase diagrams of the different systems were constructed. Finally, it is demonstrated that when pressing the bulk amorphous alloy onto a metallic dies at temperatures within the supercooled liquid region, the alloy faithfully replicates the surface...

  1. Effect of Contact Temperature Rise During Sliding on the Wear Resistance of TiNi Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    S.K. Roy Chowdhury

    2013-03-01

    Full Text Available The high wear resistance of TiNi shape memory alloys has generally been attributed to its pseudoelastic nature. In the present work the hardening effect due to its phase transformation from martensite to austenite due to frictional heating during sliding has been considered. Based on existing constitutive models that represent the experimental results of TiNi shape memory alloys a theoretical model of the dependence of wear-resistance on the contact temperature rise has been developed. The analysis was further extended to include the operating and surface roughness parameters. The model essentially indicates that for these alloys wear decreases with the rise in contact temperature over a wide range of load, speed and surface roughness combination during sliding. This means that the wear resistance of these alloys results from the very cause that is normally responsible for the increased wear and seizure of common engineering materials. Preliminary wear tests were carried out with TiNi alloys at varying ambient temperature and varying load-speed combinations and the results agree well with the theoretical predictions.

  2. Measurement and Prediction of the Thermomechanical Response of Shape Memory Alloy Hybrid Composite Beams

    Science.gov (United States)

    Davis, Brian; Turner, Travis L.; Seelecke, Stefan

    2005-01-01

    Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons within the beam structures. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical analysis/design tool. The experimental investigation is refined by a more thorough test procedure and incorporation of higher fidelity measurements such as infrared thermography and projection moire interferometry. The numerical results are produced by a recently commercialized version of the constitutive model as implemented in ABAQUS and are refined by incorporation of additional measured parameters such as geometric imperfection. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. The results demonstrate the effectiveness of SMAHC structures in controlling static and dynamic responses by adaptive stiffening. Excellent agreement is achieved between the predicted and measured results of the static and dynamic thermomechanical response, thereby providing quantitative validation of the numerical tool.

  3. Indentation response of a NiTi shape memory alloy: modeling and experiments

    Directory of Open Access Journals (Sweden)

    C. Maletta

    2012-07-01

    Full Text Available The indentation response of a pseudoelastic nickel-titanium based shape memory alloy (SMA has been analyzed. Indentation tests have been carried out at room temperature using a spherical diamond tip and indentation loads in the range 50-500 mN in order to promote a large stress-induced transformation zone in the indentation region and, consequently, to avoid local effects due to microstructural variations. The measured load-displacement data have been analyzed to obtain information on the pseudoelastic response of the alloy. To aid this analysis numerical simulations were performed, by using a commercial finite element (FE software code and a special constitutive model for SMAs, so as to understand better the microstructural evolution occurring during the indentation process. Finally, the FE model has been used to analyze the effects of temperature on the indentation response of the alloy. This analysis revealed a marked variation of both the maximum and residual penetration depths with increasing test temperature.

  4. Fabrication of NiTi shape memory alloy by Micro-FAST

    Directory of Open Access Journals (Sweden)

    Huang Kunlan

    2015-01-01

    Full Text Available A NiTi shape memory alloy, known as nitinol, has been intensively studied for last five decades. The NiTi alloy with large size is commonly produced by vacuum sintering, thermal explosion mode of self-propagating high-temperature synthesis (TE-SHS and spark plasma sintering (SPS. These methods are, however, rarely utilized for the forming of miniature and micro-sized components and have their own limits and disadvantages, such as long process chains and low efficiency with the processes. In the study reported in this paper, an innovation in rapid powder consolidation technology, called Micro-FAST (combining micro-forming and electric-current activated sintering techniques (FAST is introduced for the forming of micro-components in which the loose powders are loaded directly into the die, followed by electric-sintering. In the study, Φ4.0 mm × 4.0 mm miniature cylinders were formed with pre-alloyed NiTi powders. Sintered sample with relative density of 98.65% has been fabricated at a sintering temperature of 1150 °C in a relatively short cycle time (119.5 s. Based on the results of SEM and XRD, it was found that the densified samples with Ni3Ti, NiTi and NiTi2 phases were produced.

  5. Mathematical Modeling and Control of Nonlinear Oscillators with Shape Memory Alloys

    Science.gov (United States)

    Bendame, Mohamed

    Shape memory alloys (SMAs) belong to an interesting type of materials that have attracted the attention of scientists and engineers over the last few decades. They have some interesting properties that made them the subject of extensive research to find the best ways to utilize them in different engineering, biomedical, and scientific applications. In this thesis, we develop a mathematical model and analyze the behavior of SMAs by considering a one degree of freedom nonlinear oscillator consisting of a mass connected to a fixed frame through a viscous damping and a shape memory alloy device. Due to the nonlinear and dissipative nature of shape memory alloys, optimal control and Lyapunov stability theories are used to design a controller to stabilize the response of the one degree of freedom nonlinear oscillator. Since SMAs exist in two phases, martensite and austenite, and their phase transformations are dependent on stress and temperature, this work is presented in two parts. The first part deals with the nonlinear oscillator system in its two separate phases by considering a temperature where the SMA exists in only one of the phases. A model for each phase is developed based on Landau-Ginzburg-Devonshire theory that defines the free energy in a polynomial form enabling us to describe the SMAs shape memory effect and pseudoelasticity. However, due to the phenomenon of hysteresis in SMAs, the response of the nonlinear oscillator with a SMA element, in either phase, is chaotic and unstable. In order to stabilize the chaotic behavior, an optimal linear quadratic regulator controller is designed around a stable equilibrium for the martensitic and the austenitic phases. The closed-loop response for each phase is then simulated and computational results are presented. The second part of the thesis deals with the entire system in its dynamics by combining the two phases and taking into account the effect of temperature on the response of the system. Governing equations

  6. Cell memory-based therapy.

    Science.gov (United States)

    Anjamrooz, Seyed Hadi

    2015-11-01

    Current cell therapies, despite all of the progress in this field, still faces major ethical, technical and regulatory hurdles. Because these issues possibly stem from the current, restricted, stereotypical view of cell ultrastructure and function, we must think radically about the nature of the cell. In this regard, the author's theory of the cell memory disc offers 'memory-based therapy', which, with the help of immune system rejuvenation, nervous system control and microparticle-based biodrugs, may have substantial therapeutic potential. In addition to its potential value in the study and prevention of premature cell aging, age-related diseases and cell death, memory therapy may improve the treatment of diseases that are currently limited by genetic disorders, risk of tumour formation and the availability and immunocompatibility of tissue transplants. © 2015 The Authors. Journal of Cellular and Molecular Medicine published by John Wiley & Sons Ltd and Foundation for Cellular and Molecular Medicine.

  7. INFLUENCE OF PROCESSING ON SHAPE MEMORY EFFECT OF Fe-Mn-Si-Ni-C-RE SHAPE MEMORY ALLOY

    Institute of Scientific and Technical Information of China (English)

    N.C. Si; Z.H. Jia; L.B. Qi

    2003-01-01

    Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with .compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%o). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃), ε→γtransition completed in 1os meanwhile the relative shape recovery ratio of the alloy increased rapidly.

  8. Constitutive modeling of shape memory alloys at finite strain

    Energy Technology Data Exchange (ETDEWEB)

    Pethoe, A. [Technical Univ. Budapest (Hungary). Dept. of Applied Mechanics

    2001-07-01

    A new model which is able to reproduce the basic responses of shape memory materials on both micro- and macrostructural aspects is presented. The model is based on a local finite strain continuum description and uses a multiplicative decomposition of the total deformation gradient which involves elastic, plastic and microstructurally given phase transitional parts. For the elastic behavior of the material a coupled hyper-hypoelastic model is used based on a recently developed logarithmic rate. A complex constitutive equation is presented which consists of the kinetics of phase change process given by thermodynamical basis. Finally a simple one dimensional example is also shown. (orig.)

  9. Magnesium-based biodegradable alloys: Degradation, application, and alloying elements.

    Science.gov (United States)

    Pogorielov, Maksym; Husak, Eugenia; Solodivnik, Alexandr; Zhdanov, Sergii

    2017-03-01

    In recent years, the paradigm about the metal with improved corrosion resistance for application in surgery and orthopedy was broken. The new class of biodegradable metal emerges as an alternative for biomedical implants. These metals corrode gradually with an appropriate host response and release of corrosion products. And it is absolutely necessary to use essential metals metabolized by hosting organism with local and general nontoxic effect. Magnesium serves this aim best; it plays the essential role in body metabolism and should be completely excreted within a few days after degradation. This review summarizes data from Mg discovery and its first experimental and clinical application of modern concept of Mg alloy development. We focused on biodegradable metal application in general surgery and orthopedic practice and showed the advantages and disadvantages Mg alloys offer. We focused on methods of in vitro and in vivo investigation of degradable Mg alloys and correlation between these methods. Based on the observed data, a better way for new alloy pre-clinical investigation is suggested. This review analyzes possible alloying elements that improve corrosion rate, mechanical properties, and gives the appropriate host response.

  10. Iron-based amorphous alloys and methods of synthesizing iron-based amorphous alloys

    Science.gov (United States)

    Saw, Cheng Kiong; Bauer, William A.; Choi, Jor-Shan; Day, Dan; Farmer, Joseph C.

    2016-05-03

    A method according to one embodiment includes combining an amorphous iron-based alloy and at least one metal selected from a group consisting of molybdenum, chromium, tungsten, boron, gadolinium, nickel phosphorous, yttrium, and alloys thereof to form a mixture, wherein the at least one metal is present in the mixture from about 5 atomic percent (at %) to about 55 at %; and ball milling the mixture at least until an amorphous alloy of the iron-based alloy and the at least one metal is formed. Several amorphous iron-based metal alloys are also presented, including corrosion-resistant amorphous iron-based metal alloys and radiation-shielding amorphous iron-based metal alloys.

  11. Shape memory alloy smart knee spacer to enhance knee functionality: model design and finite element analysis.

    Science.gov (United States)

    Gautam, Arvind; Rani, A Bhargavi; Callejas, Miguel A; Acharyya, Swati Ghosh; Acharyya, Amit; Biswas, Dwaipayan; Bhandari, Vasundhra; Sharma, Paresh; Naik, Ganesh R; Gautam, Arvind; Rani, A Bhargavi; Callejas, Miguel A; Acharyya, Swati Ghosh; Acharyya, Amit; Biswas, Dwaipayan; Bhandari, Vasundhra; Sharma, Paresh; Naik, Ganesh R; Acharyya, Swati Ghosh; Sharma, Paresh; Bhandari, Vasundhra; Rani, A Bhargavi; Gautam, Arvind; Biswas, Dwaipayan; Callejas, Miguel A; Acharyya, Amit

    2016-08-01

    In this paper we introduce Shape Memory Alloy (SMA) for designing the tibial part of Total Knee Arthroplasty (TKA) by exploiting the shape-memory and pseudo-elasticity property of the SMA (e.g. NiTi). This would eliminate the drawbacks of the state-of-the art PMMA based knee-spacer including fracture, sustainability, dislocation, tilting, translation and subluxation for tackling the Osteoarthritis especially for the aged people of 45-plus or the athletes. In this paper a Computer Aided Design (CAD) model using SolidWorks for the knee-spacer is presented based on the proposed SMA adopting the state-of-the art industry-standard geometry that is used in the PMMA based spacer design. Subsequently Ansys based Finite Element Analysis is carried out to measure and compare the performance between the proposed SMA based model with the state-of-the art PMMA ones. 81% more bending is noticed in the PMMA based spacer compared to the proposed SMA that would eventually cause fracture and tilting or translation of spacer. Permanent shape deformation of approximately 58.75% in PMMA based spacer is observed compared to recoverable 11% deformation in SMA when same load is applied on both separately.

  12. Improving Robustness of Tuned Vibration Absorbers Using Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Mohammad H. Elahinia

    2005-01-01

    Full Text Available A conventional passive tuned vibration absorber (TVA is effective when it is precisely tuned to the frequency of a vibration mode; otherwise, it may amplify the vibrations of the primary system. In many applications, the frequency often changes over time. For example, adding or subtracting external mass on the existing primary system results in changes in the system’s natural frequency. The frequency changes of the primary system can significantly degrade the performance of TVA. To cope with this problem, many alternative TVAs (such as semiactive, adaptive, and active TVAs have been studied. As another alternative, this paper investigates the use of Shape Memory Alloys (SMAs in passive TVAs in order to improve the robustness of the TVAs subject to mass change in the primary system. The proposed SMA-TVA employs SMA wires, which exhibit variable stiffness, as the spring element of the TVA. This allows us to tune effective stiffness of the TVA to adapt to the changes in the primary system's natural frequency. The simulation model, presented in this paper, contains the dynamics of the TVA along with the SMA wire model that includes phase transformation, heat transfer, and the constitutive relations. Additionally, a PID controller is included for regulating the applied voltage to the SMA wires in order to maintain the desired stiffness. The robustness analysis is then performed on both the SMA-TVA and the equivalent passive TVA. For our robustness analysis, the mass of the primary system is varied by ± 30% of its nominal mass. The simulation results show that the SMA-TVA is more robust than the equivalent passive TVA in reducing peak vibrations in the primary system subject to change of its mass.

  13. Improved Damage Resistant Composite Materials Incorporating Shape Memory Alloys

    Science.gov (United States)

    Paine, Jeffrey S. N.; Rogers, Craig A.

    1996-01-01

    Metallic shape memory alloys (SMA) such as nitinol have unique shape recovery behavior and mechanical properties associated with a material phase change that have been used in a variety of sensing and actuation applications. Recent studies have shown that integrating nitinol-SMA actuators into composite materials increases the composite material's functionality. Hybrid composites of conventional graphite/epoxy or glass/epoxy and nitinol-SMA elements can perform functions in applications where monolithic composites perform inadequately. One such application is the use of hybrid composites to function both in load bearing and armor capacities. While monolithic composites with high strength-to-weight ratios function efficiently as loadbearing structures, because of their brittle nature, impact loading can cause significant catastrophic damage. Initial composite failure modes such as delamination and matrix cracking dissipate some impact energy, but when stress exceeds the composite's ultimate strength, fiber fracture and material perforation become dominant. One of the few methods that has been developed to reduce material perforation is hybridizing polymer matrix composites with tough kevlar or high modulus polyethynylene plies. The tough fibers increase the impact resistance and the stiffer and stronger graphite fibers carry the majority of the load. Similarly, by adding nitinol-SMA elements that absorb impact energy through the stress-induced martensitic phase transformation, the composites' impact perforation resistance can be greatly enhanced. The results of drop-weight and high velocity gas-gun impact testing of various composite materials will be presented. The results demonstrate that hybridizing composites with nitinol-SMA elements significantly increases perforation resistance compared to other traditional toughening elements. Inspection of the composite specimens at various stages of perforation by optical microscope illustrates the mechanisms by which

  14. Mechanical Properties and Transformation Behavior of NiTiNb Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    Liu Wei; Zhao Xinqing

    2009-01-01

    NiTiNb shape memory alloys have attracted much attention in pipe coupling or sealing system because of their large transformation hysteresis upon a proper pre-deformation. In order to clarify the effects of adding Nb on the mechanical properties as well as the transformation behavior of NiTiNb shape memory alloys, Ni_(47)Ti_(44)Nb_9 and Ni_(49.8)Ti_(45.2)Nb_5 alloys with different microstructures but with similar martensitic transformation start temperature, are prepared. Comparative studies on the microstructures, mechanical properties and transformation characteristics are conducted by means of scanning electron microscopy (SEM), phase transformation measurements and mechanical property tests. It is found that Ni_(47)Ti_(44)Nb_9 and Ni49.8Ti45.2Nb5 alloys possess similar transformation hysteresis in the as-annealed state. However, the presence of Nb and its status exerts important effects on the mechanical properties, especially the yield strength and the yield behavior of the alloys. Ni_(49.8)Ti_(45.2)Nb_5 alloy exhibits remarkable increase in the yield strength than the Ni_(47)Ti_(44)Nb_9 alloy. The transformation hysteresis of both alloys under pre-deformation is characterized and the relative mechanism is discussed.

  15. Martensitic transformation and shape memory effect in NiTi alloy covered by chitosan/silver layer

    Directory of Open Access Journals (Sweden)

    Goryczka Tomasz

    2015-01-01

    Full Text Available The NiTi shape memory alloy was covered with chitosan/silver layer. Coatings were deposited at room temperature using combination of processing parameters such as deposition voltage and amount of silver in colloidal suspension. Structure of layers was studied by means of X-ray diffraction. Quality of the coatings was evaluated basing on observations done in scanning electron microscopy. Transformation behaviour of coated samples was studied with use of differential scanning calorimeter. The covered sample revealed presence of the reversible martensitic transformation and ability to deformation (in bending mode up to 8%. Forward martensitic transformation, in as-received NiTi alloy and in alloy after layer deposition occurred in two steps B2-R-B19’. After deformation quality of the chitosan/silver layer remained unchanged.

  16. F-Alloy: An Alloy Based Model Transformation Language

    OpenAIRE

    Gammaitoni, Loïc; Kelsen, Pierre

    2015-01-01

    Model transformations are one of the core artifacts of a model-driven engineering approach. The relational logic language Alloy has been used in the past to verify properties of model transformations. In this paper we introduce the concept of functional Alloy modules. In essence a functional Alloy module can be viewed as an Alloy module representing a model transformation. We describe a sublanguage of Alloy called F-Alloy that allows the specification of functional Alloy modules. Module...

  17. A 3-D constitutive model for pressure-dependent phase transformation of porous shape memory alloys.

    Science.gov (United States)

    Ashrafi, M J; Arghavani, J; Naghdabadi, R; Sohrabpour, S

    2015-02-01

    Porous shape memory alloys (SMAs) exhibit the interesting characteristics of porous metals together with shape memory effect and pseudo-elasticity of SMAs that make them appropriate for biomedical applications. In this paper, a 3-D phenomenological constitutive model for the pseudo-elastic behavior and shape memory effect of porous SMAs is developed within the framework of irreversible thermodynamics. Comparing to micromechanical and computational models, the proposed model is computationally cost effective and predicts the behavior of porous SMAs under proportional and non-proportional multiaxial loadings. Considering the pressure dependency of phase transformation in porous SMAs, proper internal variables, free energy and limit functions are introduced. With the aim of numerical implementation, time discretization and solution algorithm for the proposed model are also presented. Due to lack of enough experimental data on multiaxial loadings of porous SMAs, we employ a computational simulation method (CSM) together with available experimental data to validate the proposed constitutive model. The method is based on a 3-D finite element model of a representative volume element (RVE) with random pores pattern. Good agreement between the numerical predictions of the model and CSM results is observed for elastic and phase transformation behaviors in various thermomechanical loadings.

  18. Effect of heat treatment on transformation behavior of Ti-Ni-V shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    He Zhirong, E-mail: hezhirong01@163.com [School of Materials Science and Engineering, Shaanxi University of Technology, Hanzhong 723003 (China); Liu Manqian [School of Materials Science and Engineering, Shaanxi University of Technology, Hanzhong 723003 (China)

    2011-08-25

    Highlights: {yields} New shape memory alloy (SMA) - Ti-50.8Ni-0.5V SMA. {yields} The evolution laws of transformation types of annealed Ti-50.8Ni-0.5V SMA. {yields} The evolution laws of transformation types of aged Ti-50.8Ni-0.5V SMA. {yields} The effect laws of annealing on transformation temperature and hysteresis of the alloy. {yields} The effect laws of aging on transformation temperature and hysterises of the alloy. - Abstract: Effects of annealing and aging processes on the transformation behaviors of Ti-50.8Ni-0.5V (atomic fraction, %) shape memory alloy were investigated by means of differential scanning calorimetry (DSC). The A {yields} R/R {yields} A (A - parent phase, R - R phase) type one-stage reversible transformation occurs in 350-400 deg. C annealed alloy, the A {yields} R {yields} M/M {yields} R {yields} A (M - martensite) type two-stage transformation occurs in 450-500 deg. C annealed alloy, the A {yields} R {yields} M/M {yields} A type transformation occurs in 550 deg. C annealed alloy, and A {yields} M/M {yields} A type transformation occurs in the alloy annealed at above 600 deg. C upon cooling/heating. The transformation type of 300 deg. C aged alloy is A {yields} R/R {yields} A, and that of 500 deg. C aged alloy is A {yields} R {yields} M/M {yields} A, while that of 400 deg. C aged alloy changes from A {yields} R/R {yields} A to A {yields} R {yields} M/M {yields} R {yields} A with increasing aging time. The effects of annealing and aging processes on R and M transformation temperatures and temperature hysteresis are given. The influence of annealing and aging temperature on transformation behaviors is stronger than that of annealing and aging time.

  19. The effects of alloying elements Al and In on Ni-Mn-Ga shape memory alloys, from first principles.

    Science.gov (United States)

    Chen, Jie; Li, Yan; Shang, Jia-Xiang; Xu, Hui-Bin

    2009-01-28

    The electronic structures and formation energies of the Ni(9)Mn(4)Ga(3-x)Al(x) and Ni(9)Mn(4)Ga(3-x)In(x) alloys have been investigated using the first-principles pseudopotential plane-wave method based on density functional theory. The results show that both the austenite and martensite phases of Ni(9)Mn(4)Ga(3) alloy are stabilized by Al alloying, while they become unstable with In alloying. According to the partial density of states and structural energy analysis, different effects of Al and In alloying on the phase stability are mainly attributed to their chemical effects. The formation energy difference between the austenite and martensite phases decreases with Al or In alloying, correlating with the experimentally reported changes in martensitic transformation temperature. The shape factor plays an important role in the decrease of the formation energy difference.

  20. Effects of Stoichiometry on Transformation Temperatures and Actuator-Type Performance of NiTiPd and NiTiPdX High-Temperature Shape Memory Alloys

    Science.gov (United States)

    Bigelow, Glen S.; Gaydosh, Darrell; Garg, Anita; Padula, Santo A., II; Noebe, Ronald D.

    2007-01-01

    High-temperature shape memory NiTiPd and NiTiPdX (X=Au, Pt, Hf) alloys were produced with titanium equivalent (Ti+Hf) compositions of 50.5, 50.0, 49.5, and 49.0 at.%. Thermo-mechanical testing in compression was used to evaluate the transformation temperatures, transformation strain, work output, and permanent deformation behavior of each alloy to study the effects of quaternary alloying and stoichiometry on high-temperature shape memory alloy behavior. Microstructural evaluation showed the presence of second phases for all alloy compositions. No load transformation temperatures in the stoichiometric alloys were relatively unchanged by Au and Pt substitutions, while the substitution of Hf for Ti causes a drop in transformation temperatures. The NiTiPd, NiTiPdAu and NiTiPdHf alloys exhibited transformation temperatures that were highest in the Ti-rich compositions, slightly lower at stoichiometry, and significantly reduced when the Ti equivalent composition was less than 50 at.%. For the NiTiPdPt alloy, transformation temperatures were highest for the Ti-rich compositions, lowest at stoichiometry, and slightly higher in the Ni-rich composition. When thermally cycled under constant stresses of up to 300 MPa, all of the alloys had transformation strains, and therefore work outputs, which increased with increasing stress. In each series of alloys, the transformation strain and thus work output was highest for stoichiometric or Ti-rich compositions while permanent strain associated with the constant-load thermal cycling was lowest for alloys with Ni-equivalent-rich compositions. Based on these results, basic rules for optimizing the composition of NiTiPd alloys for actuator performance will be discussed.

  1. The Effects of Grain Size on the Martensitic Transformation in Copper-Zinc-Aluminum Shape Memory Alloys.

    Science.gov (United States)

    1982-12-01

    production or nearly so. In the medical arts these alloys are being exploited for their SME properties as orthodontic appliances, intercranial aneurism...treatment is applicable to the Cu-Zn-Al alloys. 60 LIST OF REFERENCES 1. Wayman, C. M., "Some Applications of Shape Memory Alloys," Journal of Metals, pp

  2. Corrosion resistance of benzotriazole passivated Cu-Zn-Al shape memory alloy in artificial Ringer's solution

    Institute of Scientific and Technical Information of China (English)

    LIANG Chenghao; CHEN Bangyi; CHEN Wan; WANG Hua

    2005-01-01

    The corrosion resistance of the Cu-Zn-Al shape memory alloy passivated by benzotriazole was investigated by salt spraying test and electrochemical methods in artificial Ringer's solution. The results showed that after benzotriazole passivation, the corrosion resistance of the Cu-Zn-Al shape memory alloy was improved evidently. The anodic polarization current density of the passivated alloy decreased, the mass loss reduced, the anodic passivation accelerated, the anodic active dissolution was inhibited effectively, and the surface tarnishing was restrained. Infrared reflection spectrum test showed that Cu(Ⅰ)-benzoaiazole or Cu(Ⅱ)-benzotriazole complex layer was formed on the surface of the Cu-Zn-Al shape memory alloy after passivation. This layer appeared plane, well adhesion, and presented homogeneous golden metallic luster. The corrosion resistance of the Cu-Zn-Al shape memory alloy passivated by benzotriazole is improved for the formation of an electrochemical stable baffle layer on passivated surface. This layer separates the metal substrate from the outside corrosion medium effectively and retards the corrosion process of dezincification.

  3. A free-cutting and ductile CuAlMnZnTiB shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    刘娜; 李周; 李灵; 刘斌; 李擎天; 徐根应

    2015-01-01

    The mechanical properties and cutting performance of the designed CuAlMnZnTiB shape memory alloy were studied by tensile test and microstructure observation. Using X-ray diffractometry, differential scanning calorimetry (DSC) and semi-quantitative shape memory effect test, the microstructure and shape memory effect were analyzed. It is found that lots ofβ phase and fewα phase are formed in the quenching of Cu-7.5Al-9.7Mn-3.4Zn-0.3Ti-0.14B (mass fraction, %) alloy, a great deal of martensite and fewα phase are formed in the aging alloy, while the annealing alloy is composed of a great deal ofα phase and fewβ phase. The tensile strength and elongation of the annealed alloy are 649 MPa and 17.1%, respectively. Some tiny and dispersion distributed second phase particles are generated in Ti and B precipitates, greatly improving the alloy machinability.

  4. Topology Optimization of Shape Memory Alloy Actuators using Element Connectivity Parameterization

    DEFF Research Database (Denmark)

    Langelaar, Matthijs; Yoon, Gil Ho; Kim, Yoon Young

    2005-01-01

    This paper presents the first application of topology optimization to the design of shape memory alloy actuators. Shape memory alloys (SMA’s) exhibit strongly nonlinear, temperature-dependent material behavior. The complexity in the constitutive behavior makes the topology design of SMA structures......-independent constitutive model of SMA’s is employed which allows efficient adjoint sensitivity analysis. The effectiveness of the proposed technique is illustrated by several numerical examples.In terms of computation time, the I-ECP method, a newly-developed version of ECP, is much more efficient because the degrees...

  5. Uncertainty analysis of a one-dimensional constitutive model for shape memory alloy thermomechanical description

    DEFF Research Database (Denmark)

    Oliveira, Sergio A.; Savi, Marcelo A.; Santos, Ilmar F.

    2014-01-01

    The use of shape memory alloys (SMAs) in engineering applications has increased the interest of the accuracy analysis of their thermomechanical description. This work presents an uncertainty analysis related to experimental tensile tests conducted with shape memory alloy wires. Experimental data...... are compared with numerical simulations obtained from a constitutive model with internal constraints employed to describe the thermomechanical behavior of SMAs. The idea is to evaluate if the numerical simulations are within the uncertainty range of the experimental data. Parametric analysis is also developed...

  6. Reinforcement of bulk Y-Ba-Cu-O superconductors by using Fe-Mn-Si-Ni shape memory alloy rings

    Science.gov (United States)

    Seki, H.; Honma, Y.; Nomura, M.; Nakayama, C.; Koshizuka, N.; Maruyama, T.; Murakami, M.

    Bulk Y-Ba-Cu-O superconductors are brittle ceramics and their tensional strengths are very low. Therefore, reinforcement of the bulk superconductor is needed for practical applications. Pre-compression load has been shown to be effective in enforcing the bulk superconductors. Fe-Mn-Si alloys exhibit shape-memory effects and the size change due to the shape recovery is large. Therefore, the Fe-Mn-Si shape memory alloy rings will function as effective reinforcement material for the bulk superconductors. We prepared Y-Ba-Cu-O bulk superconductors with top-seeded melt-growth process and the Ni added Fe-Mn-Si (Fe-Mn-Si-Ni) alloy ring which exhibited better shape memory performances than Ni-free Fe-Mn-Si alloys. The ring was extended by inserting a steel rod and heated to 623K. The amount of shape recovery strain was about 2%. Based on these results, the TSMG-processed bulk YBa- Cu-O superconductor 39.0 mm in diameter was inserted into the Fe-Mn-Si-Ni ring whose inner diameter was 39.3 mm at room temperature. With heating to 623K, the Fe-Mn-Si-Ni ring shrank and firmly encapsulated the bulk Y-Ba-Cu-O superconductor. Cracking was not observed in the bulk superconductor. It was interesting to note that the trapped magnetic field of the Y-Ba-Cu-O superconductor at 77K was increased from 2,550 G to 3,795 G through Fe-Mn-Si-Ni ring reinforcement. These results clearly show that the reinforcement treatment with Fe-Mn-Si-Ni alloy ring or pre-compression load is effective in improving the field trapping ability in addition to thee improvement of the mechanical properties.

  7. Effects of Ta Addition on NiTi Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@The effect of Ta addition on the martensitic transformation characteristics and the X-ray visibility on NiTi shape memory alloy have been studied in (Ni51Ti49)1-xTax system. It was found that the transformation temperatures of the Ni51Ti49 binary alloy increased drastically by an addition of 0~4 at. pct Ta, but only slightly when the concentration exceeded 4 at. pct; the addition of Ta greatly decreases the sensitivity of the martensitic transformations to the variation in the Ni-Ti ratio. The addition of Ta to the NiTi binary alloy can improve its X-ray visibility.

  8. Work Production and Variation in Shape Memory Effects during Thermal Cycling of Equiatomic TiNi Alloy

    Science.gov (United States)

    Belyaev, S.; Resnina, Natalia; Zhuravlev, R.

    2014-07-01

    The influence of thermal cycling under a symmetric scheme for work performance on the functional properties and work output of equiatomic TiNi shape memory alloys was studied. It was found that the Ti50Ni50 alloy produced an effective work output of 9.7 MJ/m3 and an efficiency of 1.47% in a symmetrical scheme for work production where the stress acting on cooling was 50 MPa, and the stress acting on heating was 200 MPa. It was observed that the Ti50Ni50 alloy demonstrated the monotonic dependence of plastic strain on the number cycle, and 3.1% of the residual strain was accumulated over 30 cycles. The data have shown that using a `symmetric' scheme for work production allows one to reduce a plastic strain 13-fold in comparison with an `asymmetric' scheme. Thus, the symmetric scheme for work production provides for the high stability of the functional properties and work output of TiNi-based shape memory alloys.

  9. Phase Transformation and Thermal Stability of Aged Ti-Ni-Hf High Temperature Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    Xianglong MENG; Wei CAI; K.T.Lau; L.M.Zhou; Liancheng ZHAO

    2006-01-01

    The use of Ni-rich TiNiHf alloys as high temperature shape memory alloys(SMAs)through aging has been presented. For Ni-rich Ti80-xNixHf20 alloys, their phase transformation temperatures are averagely increased more than 100 K by aging at 823 K for 2 h. Especially for the alloys with Ni-content of 50.4 at. pct and 50.6 at. pct, their martensitic transformation start temperatures(Ms)are more than 473 K after aging. TEM observation confirmed that some fine particles precipitate from the matrix during aging. The aged Ni-rich TiNiHf SMAs show the better thermal stability of phase transformation temperatures than the solutiontreated TiNiHf alloys. The fine particles precipitated during aging should be responsible for the increase of phase transformation temperatures and its high stability.

  10. Microstructure and Shape Memory Effect of Cu-26.1Zn-4.8Al Alloy

    Institute of Scientific and Technical Information of China (English)

    CHENG Xiaomin; HUANG Feng; LI Na; WU Xingwen

    2008-01-01

    The influence of processing parameters on the microstructure and shape memory effect of Cu-26.1Zn-4.8Al alloy was investigated. The treated specimens were characterized by metallography, X-ray diffraction (XRD) and transmission electron microscopy (TEM) to explain the mechanism of shape memory effect in Cu-26.1Zn-4.8Al alloy. The results reveal that the shape memory effect is markedly increased by appropriate quenching and ageing process. XRD shows that γ-phase precipitates from martensite when aged at higher temperature and γ precipitates impair the shape memory effect. TEM analysis indicate that the substructure of plate-like martensite consists of twins and stacking faults.

  11. Fixation of external drainage device with injectable shape-memory alloy clips.

    Science.gov (United States)

    Olson, Jeffrey L; Erlanger, Michael

    2013-09-01

    To describe a novel surgical technique and novel surgical instrumentation for fixating an extraocular drainage device used for glaucoma-filtering surgery. The technique was performed in a laboratory setting using ex-vivo porcine eyes. We describe the surgical technique of using injectable, 25-gauge shape-memory clip system to fixate an Ahmed drainage device. The use of an injectable, shape-memory alloy clip provides the advantages of rapid, easy deployment and decreased risk of late suture failure. Importantly, the injectable, shape-memory clips can be used in surgical situations where suturing is difficult and time intensive, such as those encountered during glaucoma drainage device placement. The use of an injectable, shape-memory alloy clip is a promising new surgical tool and technique for fixating an extraocular drainage device used for glaucoma surgery.

  12. Magnetic and conventional shape memory behavior of Mn-Ni-Sn and Mn-Ni-Sn(Fe) alloys

    Science.gov (United States)

    Turabi, A. S.; Lázpita, P.; Sasmaz, M.; Karaca, H. E.; Chernenko, V. A.

    2016-05-01

    Magnetic and conventional shape memory properties of Mn49Ni42Sn9(at.%) and Mn49Ni39Sn9Fe3(at.%) polycrystalline alloys exhibiting martensitic transformation from ferromagnetic austenite into weakly magnetic martensite are characterized under compressive stress and magnetic field. Magnetization difference between transforming phases drastically increases, while transformation temperature decreases with the addition of Fe. Both Mn49Ni42Sn9 and Mn49Ni39Sn9Fe3 alloys show remarkable superelastic and shape memory properties with recoverable strain of 4% and 3.5% under compression at room temperature, respectively. These characteristics can be counted as extraordinary among the polycrystalline NiMn-based magnetic shape memory alloys. Critical stress for phase transformation was increased by 34 MPa in Mn49Ni39Sn9Fe3 and 21 MPa in Mn49Ni42Sn9 at 9 T, which can be qualitatively understood in terms of thermodynamic Clausius-Clapeyron relationships and in the framework of the suggested physical concept of a volume magnetostress.

  13. EFFECTS OF HEAT TREATMENT ON THE MICROSTRUCTURE OF Cu-Zn-Al (RE) SHAPE MEMORY ALLOYS

    Institute of Scientific and Technical Information of China (English)

    N.C.Si; S.C.Sun

    2001-01-01

    The effects of heat treatment on the Cu-Zn-Al shape memory alloys with mixed REwere researched with the help of X-ray diffraction and transmission electron micro-scope (TEM).The results show that the shape memory alloys with martensite can beproduced by adding mixed RE and heat treatment processes holding at 820C -880Cfor 15min,quenching into oil,aging at 150C for 15min,and then holding in waterat 50C for 10min.The alloys have the lowest transformation thermal hysteresis.Among the four experimental heat treatment processes the gradationally quenchingmakes the alloy have the highest transformation temperature and quenching into oilor water at room temperature makes the alloy have the largest thermal hysteresis.Mi-crostructure examination shows that aging at 2000C could destroy the substructuresin lathy martensites in the alloy and form a lot of dislocations,and aging at 250℃could cause the bainite transformation in the alloy.

  14. Perpendicular Magnetic Anisotropy in Co-Based Full Heusler Alloy Thin Films

    Science.gov (United States)

    Wu, Y.; Xu, X. G.; Miao, J.; Jiang, Y.

    2015-12-01

    Half-metallic Co-based full Heusler alloys have been qualified as promising functional materials in spintronic devices due to their high spin polarization. The lack of perpendicular magnetic anisotropy (PMA) is one of the biggest obstacles restricting their application in next generation ultrahigh density storage such as magnetic random access memory (MARM). How to induce the PMA in Co-based full Heusler alloy thin films has attracted much research interest of scientists. This paper presents an overview of recent progress in this research area. We hope that this paper would provide some guidance and ideas to develop highly spin-polarized Co-based Heusler alloy thin films with PMA.

  15. A Shape-Memory Alloy Thermal Conduction Switch for Use at Cryogenic Temperatures

    Science.gov (United States)

    Vaidyanathan, Raj

    2004-01-01

    The following summarizes the activities performed under NASA grant NAG10-323 from September 1, 2002 through September 30, 2004 at the. Univ ersity of Central Florida. A version of this has already been submitt ed for publication in the international journal Swart Materials and S tructures in December 2004. Additionally, a version of this has alrea dy appeared in print in Advances in Cryogenic Engineering, American Institute of Physics, (2004) 50A 26-3; in an article entitled "A Shape Memory Alloy Based Cryogenic Thermal Conduction Switch" by V.B. Krish nan. J.D. Singh. T.R. Woodruff. W.U. Notardonato and R. Vaidyanathan (article is attached at the end of this report).

  16. A novel shape memory alloy microactuator for large in-plane strokes and forces

    Science.gov (United States)

    Kabla, M.; Ben-David, E.; Shilo, D.

    2016-07-01

    This paper describes a novel concept for in-plane actuators based on a thin free-standing shape memory alloy (SMA) film. The presented guidelines can be used to design a variety of actuators that can provide a combination of large strokes and forces for linear and rotary motions. A prototype actuator demonstrated a displacement of 45 μm related to 4.5% of the SMA film length, and a force of up to 115 mN related to a stress of 230 MPa in the SMA film without plastic deformations. These capabilities allow the actuator to work against the stiff springs that are essential for the devices’ ability to sustain vibrations, impacts, and accelerations.

  17. Design of a shape adaptive airfoil actuated by a Shape Memory Alloy strip for airplane tail

    Science.gov (United States)

    Shirzadeh, R.; Raissi Charmacani, K.; Tabesh, M.

    2011-04-01

    Of the factors that mainly affect the efficiency of the wing during a special flow regime, the shape of its airfoil cross section is the most significant. Airfoils are generally designed for a specific flight condition and, therefore, are not fully optimized in all flight conditions. It is very desirable to have an airfoil with the ability to change its shape based on the current regime. Shape memory alloy (SMA) actuators activate in response to changes in the temperature and can recover their original configuration after being deformed. This study presents the development of a method to control the shape of an airfoil using SMA actuators. To predict the thermomechanical behaviors of an SMA thin strip, 3D incremental formulation of the SMA constitutive model is implemented in FEA software package ABAQUS. The interactions between the airfoil structure and SMA thin strip actuator are investigated. Also, the aerodynamic performance of a standard airfoil with a plain flap is compared with an adaptive airfoil.

  18. Toward Low-Cost Highly Portable Tactile Displays with Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    R. Velázquez

    2007-01-01

    Full Text Available This paper presents a new concept of low-cost, high-resolution, lightweight, compact and highly portable tactile display. The prototype consists of an array of 8 × 8 upward/downward independent moveable pins based on shape memory alloy (SMA technology. Each tactile actuator consists of an antagonist arranged pair of miniature NiTi SMA helical springs capable of developing a 300 mN pull force at 1.5 Hz bandwidth by using simple forced-air convection. The proposed concept allows the development of 200 g weight tactile instruments of compact dimensions which can be easily carried by a visually disabled user. A detailed technical description of the SMA active element, tactile actuator and tactile display is presented and discussed. Preliminary perceptual results confirm the effectiveness of the display on information transmission.

  19. A three-dimensional constitutive model for magnetic shape memory alloys under magneto-mechanical loadings

    Science.gov (United States)

    Mousavi, Mohammad Reza; Arghavani, Jamal

    2017-01-01

    This paper presents a three-dimensional phenomenological constitutive model for magnetic shape memory alloys (MSMAs), developed within the framework of irreversible continuum thermodynamics. To this end, a proper set of internal variables is introduced to reflect the microstructural consequences on the material macroscopic behavior. Moreover, a stress-dependent thermodynamic force threshold for variant reorientation is introduced which improves the model accuracy. Preassumed kinetic equations for magnetic domain volume fractions, decoupled equations for magnetization unit vectors and appropriate presentation of the limit function for martensite variant reorientation lead to a simple formulation of the proposed constitutive model. To show the model capability in reproducing the main features of MSMAs, several numerical examples are solved and compared with available experimental data as well as available three-dimensional constitutive models in the literature. Demonstrating good agreement with experimental data besides possessing computational advantages, the proposed constitutive model can be used for analysis of MSMA-based smart structures.

  20. Coupling of metals and biominerals: characterizing the interface between ferromagnetic shape-memory alloys and hydroxyapatite.

    Science.gov (United States)

    Allenstein, Uta; Selle, Susanne; Tadsen, Meike; Patzig, Christian; Höche, Thomas; Zink, Mareike; Mayr, Stefan G

    2015-07-22

    Durable, mechanically robust osseointegration of metal implants poses one of the largest challenges in contemporary orthopedics. The application of biomimetic hydroxyapatite (HAp) coatings as mediators for enhanced mechanical coupling to natural bone constitutes a promising approach. Motivated by recent advances in the field of smart metals that might open the venue for alternate therapeutic concepts, we explore their mechanical coupling to sputter-deposited HAp layers in a combined experimental-theoretical study. While experimental delamination tests and comprehensive structural characterization, including high-resolution transmission electron microscopy, are utilized to establish structure-property relationships, density functional theory based total energy calculations unravel the underlying physics and chemistry of bonding and confirm the experimental findings. Experiments and modeling indicate that sputter-deposited HAp coatings are strongly adherent to the exemplary ferromagnetic shape-memory alloys, Ni-Mn-Ga and Fe-Pd, with delamination stresses and interface bonding strength exceeding the physiological scales by orders of magnitude.

  1. Fiber-optic nonlinear endomicroscopy with focus scanning by using shape memory alloy actuation

    Science.gov (United States)

    Wu, Yicong; Zhang, Yuying; Xi, Jiefeng; Li, Ming-Jun; Li, Xingde

    2010-01-01

    A miniature fiber optic endomicroscope with built-in dynamic focus scanning capability is developed for the first time for 3-D two-photon fluorescence (TPF) imaging of biological samples. Fast 2-D lateral beam scanning is realized by resonantly vibrating a double-clad fiber cantilever with a tubular piezoactuator. Slow axial scanning is achieved by moving the distal end of the imaging probe with an extremely compact electrically driven shape memory alloy (SMA). The 10-mm-long SMA allows 150-μm contractions with a driving voltage varying only from 50 to 100 mV. The response of the SMA contraction with the applied voltage is nonlinear, but repeatable and can be accurately calibrated. Depth-resolved imaging of acriflavine-stained biological tissues and unstained white paper with the endomicroscope is performed, and the results demonstrate the feasibility of 3-D nonlinear optical imaging with the SMA-based scanning fiber-optic endomicroscope. PMID:21198147

  2. A Computational Fluid Dynamics (CFD) Analysis of an Undulatory Mechanical Fin Driven by Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Yong-Hua Zhang; Jian-Hui He; Jie Yang; Shi-Wu Zhang; Kin Huat Low

    2006-01-01

    Many fishes use undulatory fin to propel themselves in the underwater environment. These locomotor mechanisms have a popular interest to many researchers. In the present study, we perform a three-dimensional unsteady computation of an undulatory mechanical fin that is driven by Shape Memory Alloy (SMA). The objective of the computation is to investigate the fluid dynamics of force production associated with the undulatory mechanical fin. An unstructured,grid-based, unsteady Navier-Stokes solver with automatic adaptive remeshing is used to compute the unsteady flow around the fin through five complete cycles. The pressure distribution on fin surface is computed and integrated to provide fin forces which are decomposed into lift and thrust. The velocity field is also computed throughout the swimming cycle. Finally, a comparison is conducted to reveal the dynamics of force generation according to the kinematic parameters of the undulatory fin (amplitude, frequency and wavelength).

  3. Effect of Training on Two-way Shape Memory Effect and Its Stability in a Ti-Ni-Hf High Temperature Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Xianglong MENG; Wei CAI; K.T. LAU; L.M. ZHOU; Liancheng ZHAO

    2003-01-01

    The Effect of the thermal cycling training under constant strain on the two-way shape memory effect (TWSME) in a Ti36Ni49Hf15 high temperature shape memory alloy (SMA) has been investigated by bending tests. The results indicated that the training procedure is beneficial to get the better TWSME. The two-way shape memory strain increases with increasing the training strain. And it decreases with increasing the training temperature. The TWSME obtained in the present alloy shows poorer stability compared with that obtained in the TiNi alloys.

  4. Long-Time Stability of Ni-Ti-Shape Memory Alloys for Automotive Safety Systems

    Science.gov (United States)

    Strittmatter, Joachim; Gümpel, Paul

    2011-07-01

    In automotive a lot of electromagnetically, pyrotechnically or mechanically driven actuators are integrated to run comfort systems and to control safety systems in modern passenger cars. Using shape memory alloys (SMA) the existing systems could be simplified, performing the same function through new mechanisms with reduced size, weight, and costs. A drawback for the use of SMA in safety systems is the lack of materials knowledge concerning the durability of the switching function (long-time stability of the shape memory effect). Pedestrian safety systems play a significant role to reduce injuries and fatal casualties caused by accidents. One automotive safety system for pedestrian protection is the bonnet lifting system. Based on such an application, this article gives an introduction to existing bonnet lifting systems for pedestrian protection, describes the use of quick changing shape memory actuators and the results of the study concerning the long-time stability of the tested NiTi-wires. These wires were trained, exposed up to 4 years at elevated temperatures (up to 140 °C) and tested regarding their phase change temperatures, times, and strokes. For example, it was found that A P-temperature is shifted toward higher temperatures with longer exposing periods and higher temperatures. However, in the functional testing plant a delay in the switching time could not be detected. This article gives some answers concerning the long-time stability of NiTi-wires that were missing till now. With this knowledge, the number of future automotive applications using SMA can be increased. It can be concluded, that the use of quick changing shape memory actuators in safety systems could simplify the mechanism, reduce maintenance and manufacturing costs and should be insertable also for other automotive applications.

  5. Microstructure, Compression Property and Shape Memory Effect of Equiatomic TaRu High Temperature Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Xin GAO; Yufeng ZHENG; Wei CAI; Su ZHANG; Liancheng ZHAO

    2004-01-01

    The microstructure, phase transformation, compression property and strain recovery characteristics of equiatomic TaRu super high temperature shape memory alloy have been studied by optical microscope, XRD, DTA, compression tests and TEM observations. When cooling the alloy specimen from high temperature to the room temperature,β(parent phase)→β′(interphase) →β"(martensite) two-step phase transformations occur. The microstructure at room temperature show regularly arranged band morphology, with the monoclinic crystal structure. The twinning relationship between the martensite bands is determined to be (101) of Type I. Reorientation and coalescence of the martensite bands inside the variant happened during compression at room temperature. The β′→β reversible transformation contributes mainly the shape memory effect, with the maximum completely recovery strain of 2%.

  6. Memory phenomenon in a lanthanum based bulk metallic glass

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Ye [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Huang, Wei Min, E-mail: mwmhuang@ntu.edu.sg [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Zhao, Yong [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Ding, Zhen [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Li, Yan [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Tor, Shu Beng; Liu, Erjia [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore)

    2016-07-05

    In this paper, we experimentally investigate two memory phenomena in a lanthanum based bulk metallic glass (BMG). While the temperature memory effect (TME) is not found by differential scanning calorimeter (DSC) test, shape recovery is observed in samples indented at both low and high temperatures. In terms of shape memory related characteristics, this BMG shares some features of shape memory alloys (SMAs) due to its metal nature, and some other features of shape memory polymers (SMPs) owing to its glassy–rubbery transition. The formation of protrusion in the polished sample after heating to super-cooled liquid region (SCLR) indicates that surface tension is not a necessarily positive contributor for shape recovery. Release of internal elastic stress is concluded as the major player. Although the amorphous nature of BMGs enables for storing appreciable amount of internal elastic stress upon deformation, without the presence of cross-linker as in typical SMPs, the shape recovery in BMGs is rather limited. - Highlights: • Experimental investigation of shape recovery in BMG. • Surface tension is not the major reason for shape recovery in BMG. • Release of internal stress is the major contributor for shape recovery. • Comparison of shape memory features of BMG with other shape memory materials.

  7. Effect of Nb content on deformation behavior and shape memory properties of Ti–Nb alloys

    Energy Technology Data Exchange (ETDEWEB)

    Tobe, H. [Division of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Kim, H.Y., E-mail: heeykim@ims.tsukuba.ac.jp [Division of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Inamura, T.; Hosoda, H. [Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama 226-8503 (Japan); Nam, T.H. [School of Materials Science and Engineering and ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of); Miyazaki, S., E-mail: miyazaki@ims.tsukuba.ac.jp [Division of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); School of Materials Science and Engineering and ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of); Center of Excellence for Advanced Materials Research, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia)

    2013-11-15

    Highlights: ► Reorientation of martensite variants occurred by the deformation of the {1 1 1} type I and 〈2 1 1〉 type II twins. ► Magnitude of twinning shear in Ti–20Nb is larger than that in Ti–23Nb. ► Ti–20Nb exhibited a higher stress for the reorientation of martensite variants when compared with Ti–23Nb. -- Abstract: Deformation behavior and shape memory properties of Ti–(20, 23) at.% Nb alloys in a single α″ martensite state were investigated. The Ti–20Nb alloy exhibited a higher stress for the reorientation of martensite variants when compared with the Ti–23Nb alloy. The recovery strain due to the shape memory effect in the Ti–20Nb alloy was smaller than that in the Ti–23Nb alloy. Transmission electron microscope (TEM) observation revealed that the reorientation of martensite variants occurred by the deformation of {1 1 1} type I and 〈2 1 1〉 type II twins. The Nb content dependence of the deformation behavior and shape memory properties was discussed considering the magnitude of twinning shear of the twins.

  8. Accumulative Roll Bonding and Post-Deformation Annealing of Cu-Al-Mn Shape Memory Alloy

    Science.gov (United States)

    Moghaddam, Ahmad Ostovari; Ketabchi, Mostafa; Afrasiabi, Yaser

    2014-12-01

    Accumulative roll bonding is a severe plastic deformation process used for Cu-Al-Mn shape memory alloy. The main purpose of this study is to investigate the possibility of grain refinement of Cu-9.5Al-8.2Mn (in wt.%) shape memory alloy using accumulative roll bonding and post-deformation annealing. The alloy was successfully subjected to 5 passes of accumulative roll bonding at 600 °C. The microstructure, properties as well as post-deformation annealing of this alloy were investigated by optical microscopy, scanning electron microscopy, x-ray diffraction, differential scanning calorimeter, and bend and tensile testing. The results showed that after 5 passes of ARB at 600 °C, specimens possessed α + β microstructure with the refined grains, but martensite phases and consequently shape memory effect completely disappeared. Post-deformation annealing was carried out at 700 °C, and the martensite phase with the smallest grain size (less than 40 μm) was obtained after 150 s of annealing at 700 °C. It was found that after 5 passes of ARB and post-deformation annealing, the stability of SME during thermal cycling improved. Also, tensile properties of alloys significantly improved after post-deformation annealing.

  9. Lattice dynamics of ferromagnetic shape memory alloys from inelastic neutron scattering

    Energy Technology Data Exchange (ETDEWEB)

    Mehaddene, Tarik [Physik-Department E13, Technische Universitaet Muenchen, Garching (Germany); Neuhaus, Juergen [Forschungsneutronenquelle Heinz Maier-Leibnitz, Garching (Germany); Petry, Winfried [Physik-Department E13, Technische Universitaet Muenchen, Garching (Germany); Forschungsneutronenquelle Heinz Maier-Leibnitz, Garching (Germany); Hradil, Klaudia [Forschungsneutronenquelle Heinz Maier-Leibnitz, Garching (Germany); Institut fuer Physikalische Chemie, Georg-August-Universitaet, Goettingen (Germany); Bourges, Philippe [Laboratoire Leon Brillouin (LLB), CEA Saclay, Gif sur Yvette (France)

    2008-07-01

    The tendency of shape memory alloys to undergo a martensitic transItion shows up in the anomalous phonon softening of particular phonon modes in their austenitic phase. We report on phonon measurements in both austenitic and martensitic phases of Ni-based alloys. We show that, contrary to NiMnSn, the anomalous softening of the TA{sub 2}[110] phonons in NiMnGa is strongly enhanced below the Curie temperature. The measurements revealed that low restoring forces against the shearing of the (111) atomic planes along develop upon cooling. The vibrational spectra measured in two different martensitic phases of NiMnGa, namely the tetragonal 5M and the orthorhombic 7M structures, revealed fundamental differences. A dispersive low-energy excitation develops from the elastic modulation peaks in the 5M structure and come into interaction with TA{sub 2}[110] phonon branch in the q-range 0.25-0.3 r.l.u where the latter shows a wiggle in the dispersion. No wiggle is seen in the TA{sub 2}[110] branch of the 7M structure. It shows a normal sinus-like dispersion curve.

  10. Influence of volume magnetostriction on the thermodynamic properties of Ni-Mn-Ga shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Kosogor, Anna [National University of Science and Technology “MISiS,” Moscow 119049 (Russian Federation); Institute of Magnetism, 36-b, Vernadsky Str., Kyiv 03142 (Ukraine); Donetsk Institute for Physics and Engineering, Kyiv 03028 (Ukraine); L' vov, Victor A. [Institute of Magnetism, 36-b, Vernadsky Str., Kyiv 03142 (Ukraine); Faculty of Radiophysics, Electronics and Computer Systems, Taras Shevchenko University, Glushkov Str. 4G, Kyiv 01601 (Ukraine); Departament de Fisica, Universitat de les Illes Balears, Ctra. de Valldemossa, km 7.5, 07122 Palma de Mallorca (Spain); Cesari, Eduard [Departament de Fisica, Universitat de les Illes Balears, Ctra. de Valldemossa, km 7.5, 07122 Palma de Mallorca (Spain)

    2015-10-07

    In the present article, the thermodynamic properties of Ni-Mn-Ga ferromagnetic shape memory alloys exhibiting the martensitic transformations (MTs) above and below Curie temperature are compared. It is shown that when MT goes below Curie temperature, the elastic and thermal properties of alloy noticeably depend on magnetization value due to spontaneous volume magnetostriction. However, the separation of magnetic parts from the basic characteristics of MT is a difficult task, because the volume magnetostriction does not qualitatively change the transformational behaviour of alloy. This problem is solved for several Ni-Mn-Ga alloys by means of the quantitative theoretical analysis of experimental data obtained in the course of stress-strain tests. For each alloy, the entropy change and the transformation heat evolved in the course of MT are evaluated, first, from the results of stress-strain tests and, second, from differential scanning calorimetry data. For all alloys, a quantitative agreement between the values obtained in two different ways is observed. It is shown that the magnetic part of transformation heat exceeds the non-magnetic one for the Ni-Mn-Ga alloys undergoing MTs in ferromagnetic state, while the elevated values of transformation heat measured for the alloys undergoing MTs in paramagnetic state are caused by large MT strains.

  11. Influence of volume magnetostriction on the thermodynamic properties of Ni-Mn-Ga shape memory alloys

    Science.gov (United States)

    Kosogor, Anna; L'vov, Victor A.; Cesari, Eduard

    2015-10-01

    In the present article, the thermodynamic properties of Ni-Mn-Ga ferromagnetic shape memory alloys exhibiting the martensitic transformations (MTs) above and below Curie temperature are compared. It is shown that when MT goes below Curie temperature, the elastic and thermal properties of alloy noticeably depend on magnetization value due to spontaneous volume magnetostriction. However, the separation of magnetic parts from the basic characteristics of MT is a difficult task, because the volume magnetostriction does not qualitatively change the transformational behaviour of alloy. This problem is solved for several Ni-Mn-Ga alloys by means of the quantitative theoretical analysis of experimental data obtained in the course of stress-strain tests. For each alloy, the entropy change and the transformation heat evolved in the course of MT are evaluated, first, from the results of stress-strain tests and, second, from differential scanning calorimetry data. For all alloys, a quantitative agreement between the values obtained in two different ways is observed. It is shown that the magnetic part of transformation heat exceeds the non-magnetic one for the Ni-Mn-Ga alloys undergoing MTs in ferromagnetic state, while the elevated values of transformation heat measured for the alloys undergoing MTs in paramagnetic state are caused by large MT strains.

  12. Auxetic shape memory alloy cellular structures for deployable satellite antennas: design, manufacture and testing

    Directory of Open Access Journals (Sweden)

    Di Maio D.

    2010-06-01

    Full Text Available We describe the production development and experimental tests related to an hybrid honeycomb-truss made of shape memory alloy (Ni48Ti46Cu6, and used as a demonstrator for a deployable antenna in deep-space missions. Specific emphasis is placed on the modal analysis techniques used to test the lightweight SMA structure.

  13. TiNi shape memory alloy coated with tungsten : A novel approach for biomedical applications

    NARCIS (Netherlands)

    Li, Huafang; Zheng, Yufeng; Pei, Y. T.; de Hosson, Jeff

    2014-01-01

    This study explores the use of DC magnetron sputtering tungsten thin films for surface modification of TiNi shape memory alloy (SMA) targeting for biomedical applications. SEM, AFM and automatic contact angle meter instrument were used to determine the surface characteristics of the tungsten thin fi

  14. A high-rate shape memory alloy actuator for aerodynamic load control on wind turbines

    NARCIS (Netherlands)

    Lara-Quintanilla, A.; Hulskamp, A.W.; Bersee, H.E.N.

    2013-01-01

    This paper discusses the development of a high rate shape memory alloy (SMA) driven actuator. The concept of the actuator was developed to act as aerodynamic load control surface on wind turbines. It was designed as a plate or beam-like structure with prestrained SMA wires embedded off its neutral a

  15. DSC-Analysis of thermomechanically treated TiNi shape memory alloy

    NARCIS (Netherlands)

    Beyer, J.; Besselink, P.A.; Aartsen, A.J.

    1985-01-01

    The martensitic transformation behaviour, after thermomechanical treatment of the TiNi-alloy with two-way shape memory, have been studied by differential scanning calorimetry. The results are correlated with electrical resistivity and electron microscopical observations. One heating and cooling cycl

  16. Study of Friction at the Mesoscale using Nitinol Shape Memory Alloy

    CERN Document Server

    Peters, R D

    2003-01-01

    Elastic and dissipative properties of a NiTi shape memory alloy have been studied in both the martensite and austenite phases, using the free-decay of a vibrating Nitinol wire. The influence of air was estimated from a martensite measurement in vacuum.

  17. Development of a Flapping Wing Design Incorporating Shape Memory Alloy Actuation

    Science.gov (United States)

    2010-03-01

    Hong Wang , Chen-Hsien Fan. “Optimal Design of Rotary Manipulators Using Shape Memory Alloy Wire Actuated Flexures,” Sensors & Actuators A: Physical... Chih -Ming Ho. “Unsteady Aerodynamics and Flow Control for Flapping Wing Flyers,” Progress in Aerospace Sciences, 39: 635-681 (November 2003

  18. TiNi shape memory alloy coated with tungsten : A novel approach for biomedical applications

    NARCIS (Netherlands)

    Li, Huafang; Zheng, Yufeng; Pei, Y. T.; de Hosson, Jeff

    This study explores the use of DC magnetron sputtering tungsten thin films for surface modification of TiNi shape memory alloy (SMA) targeting for biomedical applications. SEM, AFM and automatic contact angle meter instrument were used to determine the surface characteristics of the tungsten thin

  19. Shape memory characteristics of Ti-Ni alloys with several specimen sizes from micrometer to millimeter

    Science.gov (United States)

    Miyazaki, Shuichi; Kitamura, Kazuhiro; Nomura, Kuniaki; Fang, Dong; Tobushi, Hisaaki

    1996-02-01

    Ti-Ni shape memory alloys with nearly equiatomic compositions were made by three types of production methods, i.e., rolling, drawing and sputtering methods. These methods were used for making thin plates 0.1 mm thick, thick and thin wires 1.0 mm and 0.08 mm in diameter, and thin films 0.007 mm thick, respectively. These specimens were annealed at 673 K, 773 K, and 873 K in order to investigate the affect of annealing temperature on the shape memory characteristics in each specimen. The shape memory characteristics were compared among these specimens in order to investigate the effect of the production method.

  20. Applications and development of shape-memory and superelastic alloys in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Takaoka, S.; Horikawa, H. [Furukawa Electric Co., Ltd., Hiratsuka (Japan); Kobayashi, J. [Japan Association of Shape Memory Alloys, Yokohama (Japan); Shimizu, K. [Kanazawa Inst. of Tech., Matsutou (Japan)

    2002-07-01

    The present situation of the applications and development of shape memory and superelastic alloys in Japan will collectively be introduced. Of many shape memory alloys, TiNi alloy systems have mostly been used for the applications from the point of view of fatigue and corrosion characteristics. Shape memory effect has been utilized for mainly thermal actuators with the form of coil springs. The effect associated with the B2 to R-phase transformation and its reversion exhibits recoverable strain of approximately 1%, and after a million thermal cycles the recovery characteristics are not affected. Thus, the effect is widely utilized as sensor flap of the air conditioner, water flow control valve, underfloor vent, automatic oil volume adjusting equipment for Shinkansen and water mixing valve. Another effect associated with the B2 to orthorhombic transformation and its reversion, as in TiNiCu alloys containing Cu more than 8%, can be applied to actuators required for 10,000 to 50,000 times life, and thus it is utilized as rice cooker, coffee maker and anti-scald valve. In Japan, however, the TiNi shape memory alloy systems are mainly used for applications using the superelasticity, like a rubber material. The superelasticity associated with the B2 to monoclinic stress-induced transformation and its reversion upon un-loading has been utilized as brassiere wire, eye glasses flame, antenna core wire for cellular phone and fishing wire, and that associated with the B2 to orthorhombic stress-induced transformation and its reversion upon un-loading has been as orthodontic wire, because the TiNiCu alloy wire exhibits smaller stress hysteresis than that of usual TiNi alloy wire. The TiNi shape memory alloy systems are now developed to make various shapes, such as tapes, foils and tubes, and the alloys with those shapes are examined to apply to medical uses, such as guide wire for catheter and catheter tube itself, and to any other uses. The development in Japan is rapidly

  1. Shape memory alloy actuation effect on subsonic static aeroelastic deformation of composite cantilever plate

    Science.gov (United States)

    Hussein, A. M. H.; Majid, D. L. Abdul; Abdullah, E. J.

    2016-10-01

    Shape memory alloy (SMA) is one of the smart materials that have unique properties and used recently in several aerospace applications. SMAs are metallic alloys that can recover permanent strains when they are heated above a certain temperature. In this study, the effects of SMA actuation on the composite plate under subsonic aeroelastic conditions are examined. The wind tunnel test is carried out for two configurations of a cantilever shape memory alloy composite plate with a single SMA wire fixed eccentrically. Strain gage data for both bending and torsional strain are recorded and demonstrated during the aeroelastic test for active and non-active SMA wire in two locations. The cyclic actuation of the SMA wire embedded inside the composite plate is also investigated during the aeroelastic test. The results show reduction in both bending and torsional strain of the composite plate after activation of the SMA wire during the wind tunnel test.

  2. Spray Forming of NiTi and NiTiPd Shape-Memory Alloys

    Science.gov (United States)

    Mabe, James; Ruggeri, Robert; Noebe, Ronald

    2008-01-01

    In the work to be presented, vacuum plasma spray forming has been used as a process to deposit and consolidate prealloyed NiTi and NiTiPd powders into near net shape actuators. Testing showed that excellent shape memory behavior could be developed in the deposited materials and the investigation proved that VPS forming could be a means to directly form a wide range of shape memory alloy components. The results of DSC characterization and actual actuation test results will be presented demonstrating the behavior of a Nitinol 55 alloy and a higher transition temperature NiTiPd alloy in the form of torque tube actuators that could be used in aircraft and aerospace controls.

  3. Apparatus and Method for Low-Temperature Training of Shape Memory Alloys

    Science.gov (United States)

    Swanger, A. M.; Fesmire, J. E.; Trigwell, S.; Gibson, T. L.; Williams, M. K.; Benafan, O.

    2015-01-01

    An apparatus and method for the low-temperature thermo-mechanical training of shape memory alloys (SMA) has been developed. The experimental SMA materials are being evaluated as prototypes for applicability in novel thermal management systems for future cryogenic applications. Alloys providing two-way actuation at cryogenic temperatures are the chief target. The mechanical training regimen was focused on the controlled movement of rectangular strips, with S-bend configurations, at temperatures as low as 30 K. The custom holding fixture included temperature sensors and a low heat-leak linear actuator with a magnetic coupling. The fixture was mounted to a Gifford-McMahon cryocooler providing up to 25 W of cooling power at 20 K and housed within a custom vacuum chamber. Operations included both training cycles and verification of shape memory movement. The system design and operation are discussed. Results of the training for select prototype alloys are presented.

  4. Spray Forming of NiTi and NiTiPd Shape-Memory Alloys

    Science.gov (United States)

    Mabe, James; Ruggeri, Robert; Noebe, Ronald

    2008-01-01

    In the work to be presented, vacuum plasma spray forming has been used as a process to deposit and consolidate prealloyed NiTi and NiTiPd powders into near net shape actuators. Testing showed that excellent shape memory behavior could be developed in the deposited materials and the investigation proved that VPS forming could be a means to directly form a wide range of shape memory alloy components. The results of DSC characterization and actual actuation test results will be presented demonstrating the behavior of a Nitinol 55 alloy and a higher transition temperature NiTiPd alloy in the form of torque tube actuators that could be used in aircraft and aerospace controls.

  5. Apparatus and method for low-temperature training of shape memory alloys

    Science.gov (United States)

    Swanger, A. M.; Fesmire, J. E.; Trigwell, S.; Gibson, T. L.; Williams, M. K.; Benafan, O.

    2015-12-01

    An apparatus and method for the low-temperature thermo-mechanical training of shape memory alloys (SMA) has been developed. The experimental SMA materials are being evaluated as prototypes for applicability in novel thermal management systems for future cryogenic applications. Alloys providing two-way actuation at cryogenic temperatures are the chief target. The mechanical training regimen was focused on the controlled movement of rectangular strips, with S-bend configurations, at temperatures as low as 30 K. The custom holding fixture included temperature sensors and a low heat-leak linear actuator with a magnetic coupling. The fixture was mounted to a Gifford-McMahon cryocooler providing up to 25 W of cooling power at 20 K and housed within a custom vacuum chamber. Operations included both training cycles and verification of shape memory movement. The system design and operation are discussed. Results of the training for select prototype alloys are presented.

  6. TiNi Shape Memory Alloy Foams Synthesized by Spacer Sintering and their Properties

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Titanium (Ti) andnickel (Ni) elemental powders were blended by ball milling and the ball milled powders were employed to fabricate TiNi shape memory alloy (SMA) foams by spacer sintering. Effect of ball milling time on phase constitutes of the sintered TiNi alloy foams was studied by X-ray diffraction (XRD) analysis. Scanning electron microscopy (SEM) was used to characterize the porous structure, and compressive tests were carried out to evaluate the mechanical properties ofthe foams. Results indicate that porosities of the TiNi alloy foams can be controlled by using the spacer sintering method, and the porosities show a significant effect on the mechanical properties and shape memory effect (SME).

  7. Memory-based logic synthesis

    CERN Document Server

    Sasao, Tsutomu

    2011-01-01

    This book describes the synthesis of logic functions using memories. It is useful to design field programmable gate arrays (FPGAs) that contain both small-scale memories, called look-up tables (LUTs), and medium-scale memories, called embedded memories. This is a valuable reference for both FPGA system designers and CAD tool developers, concerned with logic synthesis for FPGAs.

  8. Influence of process factors on shape memory effect of CuZnAl alloys

    Institute of Scientific and Technical Information of China (English)

    LIU Hai-xia; SI Nai-chao; XU Gui-fang

    2006-01-01

    Thermal cycle training of CuZnAI shape memory alloys with different transformation temperatures was carried out. The influence of different pre-strains, heat treatments and media on the shape memory effect(SME) of CuZnAl alloys with different transformation temperatures was studied by means of scanning electron microscopy(SEM) and X-ray diffractometry(XRD).Experimental results show that despite respective variation in heat treatment, medium and cycling number, the recovery rate always decreases as pre-strain increases. The decline is obvious when pre-strain is less than 2.6% but not so sharp when pre-strain exceeds 2.6%. Larger pre-strain results in more than one slip system and causes intercutting of the martensite strips among martensitic variants, then leads to the decline of SME. The SME of alloys with transformation temperatures below 347 K is larger than that of alloys beyond 361 K by 20%-40%. The recovery rate of two-step aged alloy is higher than that of step-quenched alloy by 20%-25%.During thermal cycling, the recovery rate in oil is better than that in water.

  9. Microstructure and property characterization of a modified zinc-base alloy and comparison with bearing alloys

    Science.gov (United States)

    Prasad, B. K.; Patwardhan, A. K.; Yegneswaran, A. H.

    1998-02-01

    The microstructure and physical, mechanical, and tribological properties of a modified zinc-base alloy have been characterized. In order to assess its utility as a bearing alloy, its properties have also been compared with those of a similarly processed conventional zinc-base alloy and a leaded-tin bronze (conforming to ZA27 and SAE 660 specifications, respectively) used for bearing applications. The modified zinc-base alloy shows promise in terms of better elevated-temperature strength and wear response at higher sliding speeds relative to the conventional zinc-base alloy. Interestingly, the wear behavior (especially the seizure pressure) of the modified alloy was also comparable to that of the bronze specimens at the maximum sliding speed, and was superior at the minimum sliding speed. The modified alloy also attained lower density and better hardness. Alloy behavior has been linked to the nature and type of the alloy microconstituents.

  10. Infrared Brazing of Ti50Ni50 Shape Memory Alloy and 316L Stainless Steel with Two Sliver-Based Fillers

    Science.gov (United States)

    Shiue, Ren-Kae; Chen, Chia-Pin; Wu, Shyi-Kaan

    2015-06-01

    Dissimilar infrared brazing Ti50Ni50 and AISI 316L stainless steel using two silver-based fillers, Cusil-ABA and Ticusil, was evaluated. The shear strength of the Ticusil brazed joint is higher than that of the Cusil-ABA brazed one due to the formation of better fillet. The maximum shear strength of 237 MPa is obtained for the Ticusil joint brazed at 1223 K (950 °C) for 60 seconds. The presence of interfacial Ti-Fe-(Cu) layer is detrimental to the shear strength of all joints.

  11. Engineering Design Tools for Shape Memory Alloy Actuators: CASMART Collaborative Best Practices and Case Studies

    Science.gov (United States)

    Wheeler, Robert W.; Benafan, Othmane; Gao, Xiujie; Calkins, Frederick T; Ghanbari, Zahra; Hommer, Garrison; Lagoudas, Dimitris; Petersen, Andrew; Pless, Jennifer M.; Stebner, Aaron P.; Turner, Travis L.

    2016-01-01

    The primary goal of the Consortium for the Advancement of Shape Memory Alloy Research and Technology (CASMART) is to enable the design of revolutionary applications based on shape memory alloy (SMA) technology. In order to help realize this goal and reduce the development time and required experience for the fabrication of SMA actuation systems, several modeling tools have been developed for common actuator types and are discussed herein along with case studies, which highlight the capabilities and limitations of these tools. Due to their ability to sustain high stresses and recover large deformations, SMAs have many potential applications as reliable, lightweight, solid-state actuators. Their advantage over classical actuators can also be further improved when the actuator geometry is modified to fit the specific application. In this paper, three common actuator designs are studied: wires, which are lightweight, low-profile, and easily implemented; springs, which offer actuation strokes upwards of 200 at reduced mechanical loads; and torque tubes, which can provide large actuation forces in small volumes and develop a repeatable zero-load actuation response (known as the two-way shape memory effect). The modeling frameworks, which have been implemented in the design tools, are developed for each of these frequently used SMA actuator types. In order to demonstrate the versatility and flexibility of the presented design tools, as well as validate their modeling framework, several design challenges were completed. These case studies include the design and development of an active hinge for the deployment of a solar array or foldable space structure, an adaptive solar array deployment and positioning system, a passive air temperature controller for regulation flow temperatures inside of a jet engine, and a redesign of the Corvette active hatch, which allows for pressure equalization of the car interior. For each of the presented case studies, a prototype or proof

  12. On the effects of geometry, defects, and material asymmetry on the mechanical response of shape memory alloy cellular lattice structures

    Science.gov (United States)

    Karamooz Ravari, M. R.; Nasr Esfahani, S.; Taheri Andani, M.; Kadkhodaei, M.; Ghaei, A.; Karaca, H.; Elahinia, M.

    2016-02-01

    Shape memory alloy (such as NiTi) cellular lattice structures are a new class of advanced materials with many potential applications. The cost of fabrication of these structures however is high. It is therefore necessary to develop modeling methods to predict the functional behavior of these alloys before fabrication. The main aim of the present study is to assess the effects of geometry, microstructural imperfections and material asymmetric response of dense shape memory alloys on the mechanical response of cellular structures. To this end, several cellular and dense NiTi samples are fabricated using a selective laser melting process. Both cellular and dense specimens were tested in compression in order to obtain their stress-strain response. For modeling purposes, a three -dimensional (3D) constitutive model based on microplane theory which is able to describe the material asymmetry was employed. Five finite element models based on unit cell and multi-cell methods were generated to predict the mechanical response of cellular lattices. The results show the considerable effects of the microstructural imperfections on the mechanical response of the cellular lattice structures. The asymmetric material response of the bulk material also affects the mechanical response of the corresponding cellular structure.

  13. Organic nonvolatile memory devices based on ferroelectricity

    NARCIS (Netherlands)

    Naber, R.C.G.; Asadi, K.; Blom, P.W.M.; Leeuw, D.M. de; Boer, B. de

    2010-01-01

    A memory functionality is a prerequisite for many applications of electronic devices. Organic nonvolatile memory devices based on ferroelectricity are a promising approach toward the development of a low-cost memory technology. In this Review Article we discuss the latest developments in this area w

  14. Organic Nonvolatile Memory Devices Based on Ferroelectricity

    NARCIS (Netherlands)

    Naber, Ronald C. G.; Asadi, Kamal; Blom, Paul W. M.; de Leeuw, Dago M.; de Boer, Bert

    2010-01-01

    A memory functionality is a prerequisite for many applications of electronic devices. Organic nonvolatile memory devices based on ferroelectricity are a promising approach toward the development of a low-cost memory technology. In this Review Article we discuss the latest developments in this area w

  15. Surface corrosion enhancement of passive films on NiTi shape memory alloy in different solutions.

    Science.gov (United States)

    Jinlong, Lv; Tongxiang, Liang; Chen, Wang; Limin, Dong

    2016-06-01

    The corrosion behaviors of NiTi shape memory alloy in NaCl solution, H2SO4 solution and borate buffer solution were investigated. It was found that TiO2 in passive film improved the corrosion resistance of NiTi shape memory. However, low corrosion resistance of passive film was observed in low pH value acidic solution due to TiO2 dissolution. Moreover, the corrosion resistance of NiTi shape memory alloy decreased with the increasing of passivated potential in the three solutions. The donor density in passive film increased with the increasing of passivated potential. Different solutions affect the semiconductor characteristics of the passive film. The reducing in the corrosion resistance was attributed to the more donor concentrations in passive film and thinner thickness of the passive film.

  16. Factors Affecting Transformation Temperatures in Fe-Mn-Si-Cr-Ni Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@The effects of prestrain and annealing temperature on phase transformation temperatures in Fe14Mn5Si8Cr4Ni shape memory alloy have been studied. The results showed that when the annealing temperature was 673 K, both the Af and the Ms temperatures increased appreciably as the prestrain increased, the As temperature increased slightly with increasing prestrain; the resistivity difference at 303 K between the heating and cooling curve also increased with increasing prestrain, which agreed with the recovery strain. The shape memory effect in Fe-Mn-Si-Cr-Ni shape memory alloy is caused by the stress-induced γ → ε martensite transformation and its reverse transformation. When the prestrain was 10%, the Ms temperature decreased remarkably as the annealing temperature increased.

  17. Reverse Shape Memory Effect Related to α → γ Transformation in a Fe-Mn-Al-Ni Shape Memory Alloy

    Science.gov (United States)

    Peng, Huabei; Huang, Pan; Zhou, Tiannan; Wang, Shanling; Wen, Yuhua

    2017-05-01

    In this study, we investigated the shape memory behavior and phase transformations of solution-treated Fe43.61Mn34.74Al13.38Ni8.27 alloy between room temperature and 1173 K (900 °C). This alloy exhibits the reverse shape memory effect resulting from the phase transformation of α (bcc) → γ (fcc) between 673 K and 1073 K (400 °C and 800 °C) in addition to the shape memory effect resulting from the martensitic reverse transformation of γ' (fcc) → α (bcc) below 673 K (400 °C). There is a high density of hairpin-shaped dislocations in the α phase undergoing the martensitic reverse transformation of γ' → α. The lath γ phase, which preferentially nucleates and grows in the reversed α phase, has the same crystal orientation with the reverse-transformed γ' martensite. However, the vermiculate γ phase, which is precipitated in the α phase between lath γ phase, has different crystal orientations. The lath γ phase is beneficial to attaining better reverse shape memory effect than the vermiculate γ phase.

  18. Bio-inspired Miniature Suction Cups Actuated by Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Hu Bing-Shan

    2009-09-01

    Full Text Available Wall climbing robots using negative pressure suction always employ air pumps which have great noise and large volume. Two prototypes of bio-inspired miniature suction cup actuated by shape memory alloy (SMA are designed based on studying characteristics of biologic suction apparatuses, and the suction cups in this paper can be used as adhesion mechanisms for miniature wall climbing robots without air pumps. The first prototype with a two-way shape memory effect (TWSME extension TiNi spring imitates the piston structure of the stalked sucker; the second one actuated by a one way SMA actuator with a bias has a basic structure of stiff margin, guiding element, leader and elastic element. Analytical model of the second prototype is founded considering the constitutive model of the SMA actuator, the deflection of the thin elastic plate under compound load and the thermo-dynamic model of the sealed air cavity. Experiments are done to test their suction characteristics, and the analytical model of the second prototype is simulated on Matlab/simulink platform and validated by experiments.

  19. Superelasticity and Shape Memory Behavior of NiTiHf Alloys

    Science.gov (United States)

    Sehitoglu, H.; Wu, Y.; Patriarca, L.; Li, G.; Ojha, A.; Zhang, S.; Chumlyakov, Y.; Nishida, M.

    2017-06-01

    The NiTiHf high-temperature shape memory alloys represent a significant advancement in extending the functionality of binary NiTi to elevated temperatures above 100 °C. Despite this potential, the previous results in the literature point to a disappointingly low shape memory strains with addition of Hf. On the other hand, based on theoretical analysis using the lattice constants, the transformation strains should increase substantially with increase in Hf content. The present paper addresses this discrepancy, and using atomistic simulations, determination of twinning modes in martensite with transmission electron microscopy, digital image measurements of habit plane orientation, and strains in single-crystal specimens show that the experimental transformation strains in NiTiHf indeed increase with increasing Hf to unprecedented strain levels near 20%. The Hf contents considered were in the range 6.25-25 at.%, and NiTi (0% Hf) results are provided as the baseline. The current work represents more than 60 experiments representing an extremely thorough study on single crystals and polycrystals.

  20. Bio-inspired Miniature Suction Cups Actuated by Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Hu Bing-shan

    2010-02-01

    Full Text Available Wall climbing robots using negative pressure suction always employ air pumps which have great noise and large volume. Two prototypes of bio-inspired miniature suction cup actuated by shape memory alloy (SMA are designed based on studying characteristics of biologic suction apparatuses, and the suction cups in this paper can be used as adhesion mechanisms for miniature wall climbing robots without air pumps. The first prototype with a two-way shape memory effect (TWSME extension TiNi spring imitates the piston structure of the stalked sucker; the second one actuated by a one way SMA actuator with a bias has a basic structure of stiff margin, guiding element, leader and elastic element. Analytical model of the second prototype is founded considering the constitutive model of the SMA actuator, the deflection of the thin elastic plate under compound load and the thermo-dynamic model of the sealed air cavity. Experiments are done to test their suction characteristics, and the analytical model of the second prototype is simulated on Matlab/simulink platform and validated by experiments.

  1. Electrochemical behavior of Ti-Ni shape memory alloy in fibrinogen solution

    Institute of Scientific and Technical Information of China (English)

    梁成浩; 郭海霞; 陈邦义

    2004-01-01

    Electrochemical behaviors of Ti-Ni shape memory alloy in fibrinogen solution were studied by electrochemical techniques. The results indicate that the addition of the fibrinogen has no obvious effect on the corrosion potential, but decreases the pitting potential markedly and increases the passive current densities. The analysis of energy-dispersive X-ray for samples adsorbing fibrinogen exhibits that the elements of O, C and N exist on the surface of Ti-Ni alloy. Furthermore, the scanning electron microscope micrographs confirm that the configuration of the adsorbing fibrinogen concentrating on surface defects is like cluster and the fibrinogen adsorption concentration is 96.67 mg/m2 through ultroviolet ray absorption method. Fibrinogen combined with Ti-Ni alloy surface by complex band and its electrochemical transfer accelerated the corrosion of alloy.

  2. Elastic anisotropy and low-temperature thermal expansion in the shape memory alloy Cu-Al-Zn.

    Science.gov (United States)

    Kuruvilla, Santhosh Potharay; Menon, C S

    2008-04-01

    Cu-based shape memory alloys are known for their technologically important pseudo-elastic and shapememory properties, which are intimately associated with the martensitic transformation. A combination of deformation theory and finite-strain elasticity theory has been employed to arrive at the expressions for higher order elastic constants of Cu-Al-Zn based on Keating's approach. The second- and third-order elastic constants are in good agreement with the measurements. The aggregate elastic properties like bulk modulus, pressure derivatives, mode Grüneisen parameters of the elastic waves, low temperature limit of thermal expansion, and the Anderson-Grüneisen parameter are also presented.

  3. Embedded Shape Memory Alloy Particles for the Self-Sensing of Fatigue Crack Growth in an Aluminum Alloy

    Science.gov (United States)

    Leser, William Paul

    Future aerospace vehicles will be built using novel materials for mission conditions that are difficult to replicate in a laboratory. Structural health monitoring and condition-based maintenance will be critical to ensure the reliability of such vehicles. A multi-functional aluminum alloy containing embedded shape memory alloy (SMA) particles to detect fatigue crack growth is proposed. The regions of intensified strain near the tip of a growing fatigue crack cause the SMA particles to undergo a solid-to-solid phase transformation from austenite to martensite, releasing a detectable and identifiable acoustic emission (AE) signal that can be used to locate the crack in the affected component. This study investigates the AE response of two SMA systems, Ni-Ti, and Co-Ni-Al. Tensile (Ni-Ti) and compressive (Co-Ni-Al) tests were conducted to study the strain-induced transformation response in both of the alloy systems. It was found that the critical stress for transformation in both SMA systems was easily identified by a burst of AE activity during both transformation and reverse transformation. AE signals from these experiments were collected for use as training data for a Bayesian classifier to be used to identify transformation signals in a Al7050 matrix with embedded SMA particles. The Al/SMA composite was made by vacuum hot pressing SMA powder between aluminum plates. The effect of hot pressing temperature and subsequent heat treatments (solutionizing and peak aging) on the SMA particles was studied. It was found that, at the temperatures required, Co-Ni-Al developed a second phase that restricted the transformation from austenite to martensite, thus rendering it ineffective as a candidate for the embedded particles. Conversely, Ni-Ti did survive the embedding process and it was found that the solutionizing heat treatment applied after hot pressing was the main driver in determining the final transformation temperatures for the Ni-Ti particles. The effect of hot

  4. Characterization of Ternary NiTiPt High-Temperature Shape Memory Alloys

    Science.gov (United States)

    Rios, Orlando; Noebe, Ronald; Biles, Tiffany; Garg, Anita; Palczer, Anna; Scheiman, Daniel; Seifert, Hans Jurgen; Kaufman, Michael

    2005-01-01

    Pt additions substituted for Ni in NiTi alloys are known to increase the transformation temperature of the alloy but only at fairly high Pt levels. However, until now only ternary compositions with a very specific stoichiometry, Ni50-xPtxTi50, have been investigated and then only to very limited extent. In order to learn about this potential high-temperature shape memory alloy system, a series of over twenty alloys along and on either side of a line of constant stoichiometry between NiTi and TiPt were arc melted, homogenized, and characterized in terms of their microstructure, transformation temperatures, and hardness. The resulting microstructures were examined by scanning electron microscopy and the phase compositions quantified by energy dispersive spectroscopy."Stoichiometric" compositions along a line of constant stoichiometry between NiTi to TiPt were essentially single phase but by any deviations from a stoichiometry of (Ni,Pt)50Ti50 resulted in the presence of at least two different intermetallic phases, depending on the overall composition of the alloy. Essentially all alloys, whether single or two-phase, still under went a martensitic transformation. It was found that the transformation temperatures were depressed with initial Pt additions but at levels greater than 10 at.% the transformation temperature increased linearly with Pt content. Also, the transformation temperatures were relatively insensitive to alloy stoichiometry within the range of alloys examined. Finally, the dependence of hardness on Pt content for a series of Ni50-xPtxTi50 alloys showed solution softening at low Pt levels, while hardening was observed in ternary alloys containing more than about 10 at.% Pt. On either side of these "stoichiometric" compositions, hardness was also found to increase significantly.

  5. Ab initio study of effect of Co substitution on the magnetic properties of Ni and Pt-based Heusler alloys

    Energy Technology Data Exchange (ETDEWEB)

    Roy, Tufan, E-mail: tufanroyburdwan@gmail.com [Theory and Simulations Lab, HRDS, Raja Ramanna Centre for Advanced Technology, Indore 452013 (India); Homi Bhabha National Institute, Training School Complex, Anushaktinagar, Mumbai 400094 (India); Chakrabarti, Aparna [Theory and Simulations Lab, HRDS, Raja Ramanna Centre for Advanced Technology, Indore 452013 (India); Homi Bhabha National Institute, Training School Complex, Anushaktinagar, Mumbai 400094 (India)

    2017-04-25

    Using density functional theory based calculations, we have carried out in-depth studies of effect of Co substitution on the magnetic properties of Ni and Pt-based shape memory alloys. We show the systematic variation of the total magnetic moment, as a function of Co doping. A detailed analysis of evolution of Heisenberg exchange coupling parameters as a function of Co doping has been presented here. The strength of RKKY type of exchange interaction is found to decay with the increase of Co doping. We calculate and show the trend, how the Curie temperature of the systems vary with the Co doping. - Highlights: • We discuss the effects of Co doping on magnetic properties of Ni/Pt based Heusler alloys. • Indirect RKKY interaction is maximum for shape memory alloy like systems. • We predict Pt{sub 2}MnSn as a probable ferromagnetic shape memory alloy.

  6. Elastocaloric effect in CuAlZn and CuAlMn shape memory alloys under compression.

    Science.gov (United States)

    Qian, Suxin; Geng, Yunlong; Wang, Yi; Pillsbury, Thomas E; Hada, Yoshiharu; Yamaguchi, Yuki; Fujimoto, Kenjiro; Hwang, Yunho; Radermacher, Reinhard; Cui, Jun; Yuki, Yoji; Toyotake, Koutaro; Takeuchi, Ichiro

    2016-08-13

    This paper reports the elastocaloric effect of two Cu-based shape memory alloys: Cu68Al16Zn16 (CuAlZn) and Cu73Al15Mn12 (CuAlMn), under compression at ambient temperature. The compression tests were conducted at two different rates to approach isothermal and adiabatic conditions. Upon unloading at a strain rate of 0.1 s(-1) (adiabatic condition) from 4% strain, the highest adiabatic temperature changes (ΔTad) of 4.0 K for CuAlZn and 3.9 K for CuAlMn were obtained. The maximum stress and hysteresis at each strain were compared. The stress at the maximum recoverable strain of 4.0% for CuAlMn was 120 MPa, which is 70% smaller than that of CuAlZn. A smaller hysteresis for the CuAlMn alloy was also obtained, about 70% less compared with the CuAlZn alloy. The latent heat, determined by differential scanning calorimetry, was 4.3 J g(-1) for the CuAlZn alloy and 5.0 J g(-1) for the CuAlMn alloy. Potential coefficients of performance (COPmat) for these two alloys were calculated based on their physical properties of measured latent heat and hysteresis, and a COPmat of approximately 13.3 for CuAlMn was obtained.This article is part of the themed issue 'Taking the temperature of phase transitions in cool materials'.

  7. Thermomechanical behavior of NiTiPdPt high temperature shape memory alloy springs

    Science.gov (United States)

    Nicholson, D. E.; Padula, S. A., II; Noebe, R. D.; Benafan, O.; Vaidyanathan, R.

    2014-12-01

    Transformation strains in high temperature shape memory alloys (HTSMAs) are generally smaller than for conventional NiTi alloys and can be purposefully limited in cases where stability and repeatability at elevated temperatures are desired. Yet such alloys can still be used in actuator applications that require large strokes when used in the form of springs. Thus there is a need to understand the thermomechanical behavior of shape memory alloy spring actuators, particularly those consisting of alternative alloys. In this work, a modular test setup was assembled with the objective of acquiring stroke, stress, temperature, and moment data in real time during joule heating and forced convective cooling of Ni19.5Ti50.5Pd25Pt5 HTSMA springs. The spring actuators were subjected to both monotonic axial loading and thermomechanical cycling. The role of rotational constraints (i.e., by restricting rotation or allowing for free rotation at the ends of the springs) on stroke performance was also assessed. Finally, recognizing that evolution in the material microstructure can result in changes in HTSMA spring geometry, the effect of material microstructural evolution on spring performance was examined. This was done by taking into consideration the changes in geometry that occurred during thermomechanical cycling. This work thus provides insight into designing with HTSMA springs and predicting their thermomechanical performance.

  8. An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

    Science.gov (United States)

    Jiang, Jian-Jun; Gasik, Michael

    The electrochemical properties of amorphous MgNi-based hydrogen storage alloys synthesized by mechanical alloying (MA) were evaluated. The results show that these amorphous Mg 50Ni 50 alloys exhibit a higher discharge capacity and relatively good rate capacity at a suitable grinding time while their cycle life is very poor. In order to improve the cycle life, the surface of the amorphous Mg 50Ni 50 alloy was coated with Ti, Al and Zr in Spex 8000 mill/mixer and the coating effects were further investigated. Based on experimental results, two kinds of MgNi-based amorphous alloys are designed by substituting part of Mg in MgNi-based alloys by suitable elements. These alloys are then composed of four components. Thus, the cycle life of electrodes consisting of these quaternary amorphous alloys is greatly improved.

  9. Static critical phenomena in Co-Ni-Ga ferromagnetic shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Sethi, Brahmananda, E-mail: santra@iitg.ernet.in; Sarma, S., E-mail: santra@iitg.ernet.in; Srinivasan, A., E-mail: santra@iitg.ernet.in; Santra, S. B., E-mail: santra@iitg.ernet.in [Department of Physics, Indian Institute of Technology Guwahati, Guwahati-781039 (India)

    2014-04-24

    Ferromagnetic shape memory alloys are smart materials because they exhibit temperature driven shape memory effect and magnetic field induced strain. Thus two types of energy, i.e. thermal and magnetic, are used to control their shape memory behaviour. Study of critical phenomenon in such materials has received increased experimental and theoretical attention for better understanding of the magnetic phase transition behavior as well as further development of ferromagnetic shape memory materials. In the present study we report the preparation and characterization of bulk Co{sub 45}Ni{sub 25}Ga{sub 30} alloy, prepared by a sequence of arc melting technique followed by homogenization at 1150 °C for 24 hours and ice-water quenching. Structural and magnetic properties of the alloys were studied by means of X-ray diffraction and vibrating sample magnetometer in an applied field range of ±18 kOe equipped with a high temperature oven. We have determined the critical temperature T{sub C} (∼375.5 K) and the critical exponents viz; β=0.40, γ=1.68 and δ=5.2. Asymptotic critical exponents β, γ, and δ obey Widom scaling relation, γ+β=βδ, and the magnetization data satisfy the scaling equation of state for second-order phase transition in the asymptotic critical region.

  10. Optimizing Magnetocaloric Properties of Heusler-Type Magnetic Shape Memory Alloys by Tuning Magnetostructural Transformation Parameters

    Science.gov (United States)

    Huang, Lian; Qu, Yuhai; Cong, Daoyong; Sun, Xiaoming; Wang, Yandong

    2017-08-01

    Heusler-type magnetic shape memory alloys show a magnetostructural transformation from the low-magnetization phase to the high-magnetization phase upon the application of external magnetic fields. As a result, these alloys exhibit fascinating multifunctional properties, such as magnetic shape memory effect, magnetocaloric effect, magnetoresistance, and magnetic superelasticity. All these functional properties are intimately related to the coupling of the structural and magnetic transitions. Therefore, deliberate tuning of the magnetostructural transformation parameters is essential for obtaining optimal multifunctional properties. Here, we show that by tuning the magnetostructural transformation parameters, we are able to achieve a variety of novel magnetocaloric properties with different application potentials: (1) large magnetic entropy change of 31.9 J kg-1 K-1 under a magnetic field of 5 T; (2) giant effective magnetic refrigeration capacity (251 J kg-1) with a broad operating temperature window (33 K) under a magnetic field of 5 T; (3) large reversible field-induced entropy change (about 15 J kg-1 K-1) and large reversible effective magnetic refrigeration capacity (77 J kg-1) under a magnetic field of 5 T. The balanced tuning of magnetostructural transformation parameters of magnetic shape memory alloys may provide an instructive reference to the shape memory and magnetic refrigeration communities.

  11. Effect of Trivalent Additions and Processing on Structural and Magnetic Transitions in Ni-Mn-Ga Ferromagnetic Shape Memory Alloys

    OpenAIRE

    R. P. Mathur; Singh, R. K.; Ray, S.; P. Ghosal; Chandrasekaran, V.

    2012-01-01

    Ferromagnetic shape memory Ni50Mn30Ga15Al5-xBx (x = 0, 1, and 4) alloys were prepared by vacuum arc melting and subsequent heat-treatment as well as by melt spinning to investigate the effect of trivalent element additions in ternary Ni-Mn-Ga alloys. The heat-treated alloys containing Al were reported to possess a modulated martensite structure, however alloy containing both Al and B showed a loss of modulated structure in martensite formed. The rapidly solidified alloys on the other hand sho...

  12. Phase diagram of FeNiCoAlTaB ferrous shape memory alloy on aging time

    Directory of Open Access Journals (Sweden)

    Zhijian Zhou

    2017-04-01

    Full Text Available Ferrous shape memory alloy, Fe41Ni28Co17Al11.5Ta2.5B0.05, has shown large superelastic strain and strength in previous study. In the fabrication of this alloy, aging process is crucial for the formation of shape memory effect/superelasticity. However, its phase evolution on aging time is not clearly known. In this study, we systematically studied the phase diagram of this alloy on aging time. It is found that the unaged alloy shows a strain glass transition. With the aging time proceeding, the martensitic transformation gradually emerges. The phase diagram can be explained by the formation of coherent precipitates induced by aging. The heterogeneous strain between coherent precipitates and matrix is the driving force responsible for the emerging martensitic transformation. The generic explanation is supposed to be useful in martensitic transformation engineering for developing novel shape memory alloys from non-transforming materials.

  13. The pseudoelasticity and the shape memory effect in CoNiAl alloys

    Directory of Open Access Journals (Sweden)

    Jaromir Kopecek

    2014-01-01

    Full Text Available The cobalt alloys (close to the CoNiAl stoichiometry are the less known shape memory alloys. Such behavior is consequence of the martensitic transformation. The pseudoelasticity is caused by the stress-induced martensitic transformation above the equilibrium martensite start temperature from high temperature cubic phase (austenite to lower symmetry phase (martensite. In CoNiAl the pseudoelastic behavior can be obtained by the high temperature annealing. In presented work the effect of the annealing temperature on both pseudoelastic behavior and microstructure was investigated.

  14. Theoretical description of magnetocaloric effect in the shape memory alloy exhibiting metamagnetic behavior

    Energy Technology Data Exchange (ETDEWEB)

    L' vov, Victor A. [Institute of Magnetism, Kyiv 03142 (Ukraine); Taras Shevchenko National University, Kyiv 01601 (Ukraine); Kosogor, Anna, E-mail: annakosogor@gmail.com [Institute of Magnetism, Kyiv 03142 (Ukraine); National University of Science and Technology ‘MISiS’, Moscow 119049 (Russian Federation); Barandiaran, Jose M. [BCMaterials and University of Basque Country, UPV/EHU, Bilbao 48080 (Spain); Chernenko, Volodymyr A. [BCMaterials and University of Basque Country, UPV/EHU, Bilbao 48080 (Spain); Ikerbasque, Basque Foundation for Science, Bilbao 48013 (Spain)

    2016-01-07

    A simple thermodynamic theory is proposed for the quantitative description of giant magnetocaloric effect observed in metamagnetic shape memory alloys. Both the conventional magnetocaloric effect at the Curie temperature and the inverse magnetocaloric effect at the transition from the ferromagnetic austenite to a weakly magnetic martensite are considered. These effects are evaluated from the Landau-type free energy expression involving exchange interactions in a system of a two magnetic sublattices. The findings of the thermodynamic theory agree with first-principles calculations and experimental results from Ni-Mn-In-Co and Ni-Mn-Sn alloys, respectively.

  15. Martensitic Transformation of TiNi Shape Memory Alloy Fiber Reinforced Ni Matrix Composites

    Institute of Scientific and Technical Information of China (English)

    Lishan CUI; Yan LI; Yan jun ZHENG; Huibin XU

    2003-01-01

    In this paper, a TiNi shape memory alloy fiber Ni matrix composite was fabricated by an electroplating method using TiNialloy as the cathode and Ni as the anode. The constrained martensitic transformation behaviors of the TiNi alloy were studiedby differential scanning calorimeter (DSC), and the results showed that two endothermic peaks appear on the DSC heatingcurves and the reverse transformation temperatures increase with increasing prestrain levels. Moreover, comparing to the freetransformation, the temperature window of the constrained reverse transformation is widely expanded due to the influence ofrecovery stress.

  16. Martensitic transformations and morphology studies of NiTi shape memory alloy

    Science.gov (United States)

    Murari, M. S.; Pattabi, Manjunatha

    2017-05-01

    The forward transformation temperatures Martensite Start (Ms) and Martensite Finish (Mf) during cooling, reverse transformation temperatures Austenite Start (As) and Austenite Finish (Af) during heating are very sensitive to the thermal and mechanical history of the Shape Memory Alloy (SMA). Heat treatments, cold and hot roll, thermal and mechanical cycling have great influence on the transformation temperatures. Different characterizing techniques like Differential Scanning Calorimeter (DSC), X-Ray Diffractometer (XRD), Electrical Resistivity (ER) and Thermo Mechanical Analyzer (TMA) were employed to study the phase transformation temperatures of NiTi alloy. The microstructure of the samples was studied with Atomic Force Microscope (AFM), Optical Microscope (OM) and Field Emission Scanning Electron Microscope (FESEM).

  17. The stabilization of martensite in Cu-Zn-Al-Ti-B shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Romero, R.; Stipcich, M. [Univ. Nacional del Centro de la Provincia de Buenos Aires, Tandil (AR). Inst. de Fisica de Materiales Tandil (IFIMAT); Comision de Investigaciones Cientificas de la Provincia de Buenos Aires (Argentina)

    2001-11-01

    Recent studies on aging effects in the martensite phase have shown that the addition of Ti-B to Cu-Zn-Al shape memory alloy has a notable influence on stabilization characteristics of this alloy. The overall process is delayed and the stabilization magnitude is significantly diminished. In an attempt to understand this effect the experimental results are analyzed within a cluster rearrangement model. The characteristic energy values are determined and compared with those obtained in single crystal experiments. The obtained results suggest the formation of vacancy-Ti complexes that increase the average vacancy migration energy for about 25%. (orig.)

  18. Thermal cycling effect in Cu-11.9Al-2.5Mn shape memory alloy with high Ms temperature

    Institute of Scientific and Technical Information of China (English)

    曹玲飞; 汪明朴; 李周; 徐贲; 苏玉长

    2002-01-01

    The effects of thermal cycling on martensite transformation in Cu-11. 9Al-2.5Mn(mass fraction, % ) shape memory alloy(SMA) with high Ms temperature were studied by means of electrical tension vs temperature (U-T) measurement, optical microscopy observation and X-ray diffractometry. It shows that with increasing thermal cycles, the transformation temperatures decreased, which are accompanied by changes of martensite structure such as the decline of NNN ordering degree and monoclinic angle β→90°. Compared with traditional Cu-base SMA, the alloy has rather high thermostability and can work at 200 ~ 300 ℃. Its excellent thermostability comes from two factors: 1) its β1 parent structure is stable and difficult to decompose at work temperature; 2) its martensite structure is close to N18R(β = 89.6'), which restrains the process of M18R→N18R and the tendency of martensite stabilization and decomposition.

  19. Sign reversal of transformation entropy change in Co{sub 2}Cr(Ga,Si) shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Xiao, E-mail: xu@material.tohoku.ac.jp; Omori, Toshihiro; Kainuma, Ryosuke [Department of Materials Science, Tohoku University, Sendai 980-8579 (Japan); Nagasako, Makoto [Department of Materials Science, Tohoku University, Sendai 980-8579 (Japan); Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Kanomata, Takeshi [Department of Materials Science, Tohoku University, Sendai 980-8579 (Japan); Research Institute for Engineering and Technology, Tohoku Gakuin University, Tagajo 985-8537 (Japan)

    2015-11-02

    In situ X-ray diffraction (XRD) measurements and compression tests were performed on Co{sub 2}Cr(Ga,Si) shape memory alloys. The reentrant martensitic transformation behavior was directly observed during the in situ XRD measurements. The high-temperature parent phase and low-temperature reentrant parent phase were found to have a continuous temperature dependence of lattice parameter, therefore suggesting that they are the same phase in nature. Moreover, compression tests were performed on a parent-phase single crystal sample; an evolution from normal to inverse temperature dependence of critical stress for martensitic transformation was directly observed. Based on the Clausius-Clapeyron analysis, a sign reversal of entropy change can be expected on the same alloy.

  20. Microstructure and calorimetric behavior of laser welded open cell foams in CuZnAl shape memory alloy

    Science.gov (United States)

    Biffi, Carlo Alberto; Previtali, Barbara; Tuissi, Ausonio

    Cellular shape memory alloys (SMAs) are very promising smart materials able to combine functional properties of the material with lightness, stiffness, and damping capacity of the cellular structure. Their processing with low modification of the material properties remains an open question. In this work, the laser weldability of CuZnAl SMA in the form of open cell foams was studied. The cellular structure was proved to be successfully welded in lap joint configuration by using a thin plate of the same alloy. Softening was seen in the welded bead in all the investigated ranges of process speed as well as a double stage heat affected zone was identified due to different microstructures; the martensitic transformation was shifted to higher temperatures and the corresponding peaks were sharper with respect to the base material due to the rapid solidification of the material. Anyways, no compositional variations were detected in the joints.

  1. Superelastic and shape memory properties of TixNb3Zr2Ta alloys.

    Science.gov (United States)

    Zhu, Yongfeng; Wang, Liqiang; Wang, Minmin; Liu, Zhongtang; Qin, Jining; Zhang, Di; Lu, Weijie

    2012-08-01

    The microstructure and phase constitutions of TixNb3Zr2Ta alloys (x=35, 31, 27, 23) (wt%) were studied. With a lower niobium content the grain size of β phase in TixNb3Zr2Ta alloys increased significantly, and the TixNb3Zr2Ta system was more likely to form α″ phase and even α phase. Tensile tests showed that UTS of TixNb3Zr2Ta alloys improved as the Nb content was decreased. Cyclic loading-unloading tensile tests were carried on TixNb3Zr2Ta alloys. Ti23Nb3Zr2Ta and Ti27Nb3Zr2Ta alloys featured the best superelasticity among the alloys studied. The pseudoelastic strain ratio of Ti35Nb3Zr2Ta alloy decreased a lot as the cycle number increased. Ti31Nb3Zr2Ta alloy showed only minimum superelasticity. This is because Ti23Nb3Zr2Ta and Ti27Nb3Zr2Ta alloys had higher yield strength than Ti31Nb3Zr2Ta did, which allowed martensite phase to be induced. On the contrary, Ti31Nb3Zr2Ta alloy exhibited better shape memory property than Ti27Nb3Zr2Ta, Ti23Nb3Zr2Ta and Ti35Nb3Zr2Ta titanium alloys. β phase, α phase and α″ phase were found in Ti23Nb3Zr2Ta alloy by TEM observation. The dislocation density of α phase was much lower than that of β phase due to their crystal structure difference. This may explained why Ti23Nb3Zr2Ta with α phase possessed higher tensile strength. The incomplete shape recovery of Ti23Nb3Zr2Ta alloy after unloading resulted from two sources. Plastic deformation occurred in β phase, α phase and even α″ phase under dislocation slip mechanism, and incomplete decomposition of α″ martensitic phase resulted in unrecovered strain as well. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Quenching effects in Cu-Al-Mn shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Obrado, E.; Manosa, L.; Planes, A. [Barcelona Univ. (Spain). Dept. d' Estructura i Constituents de la Materia; Romero, R.; Somoza, A. [IFIMAT, Universidad Nacional del Centro de la Provincia de Buenos Aires, Pinto 399, 7000 Tandil, and Comision de Investigaciones Cientificas de la Provincia de Buenos Aires, Buenos Aires (Argentina)

    1999-12-15

    In this paper the effect of quenching from different temperatures (T{sub q}) in a Cu-Al-Mn alloy is studied. This alloy system, which displays an L2{sub 1} ordered structure, transforms martensitically at an intermediate temperature T{sub M}, and undergoes a spin freezing process at a lower temperature T{sub f}. Positron annihilation measurements have shown that after the quench, an excess of vacancies is retained in the system, depending on T{sub q}. In addition, both T{sub M} and T{sub f} have been found to be sensitive to T{sub q}. This has been attributed to frozen-in disorder induced by the quench. Experimental results have been interpreted in terms of the growth of magnetic clusters, quenched-in vacancies and atomic disorder. (orig.)

  3. Improvement in the Shape Memory Response of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy with Scandium Microalloying

    Science.gov (United States)

    Atli, K. C.; Karaman, I; Noebe, R. D.; Garg, A.; Chumlyakov, Y. I.; Kireeva, I. V.

    2010-01-01

    A Ti(50.5)Ni(24.5)Pd25 high-temperature shape memory alloy (HTSMA) is microalloyed with 0.5 at. pct scandium (Sc) to enhance its shape-memory characteristics, in particular, dimensional stability under repeated thermomechanical cycles. For both Ti(50.5)Ni(24.5)Pd25 and the Sc-alloyed material, differential scanning calorimetry is conducted for multiple cycles to characterize cyclic stability of the transformation temperatures. The microstructure is evaluated using electron microscopy, X-ray diffractometry, and wavelength dispersive spectroscopy. Isobaric thermal cycling experiments are used to determine transformation temperatures, dimensional stability, and work output as a function of stress. The Sc-doped alloy displays more stable shape memory response with smaller irrecoverable strain and narrower thermal hysteresis than the baseline ternary alloy. This improvement in performance is attributed to the solid solution hardening effect of Sc.

  4. Improvement in the Shape Memory Response of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy with Scandium Microalloying

    Science.gov (United States)

    Atli, K. C.; Karaman, I; Noebe, R. D.; Garg, A.; Chumlyakov, Y. I.; Kireeva, I. V.

    2010-01-01

    A Ti(50.5)Ni(24.5)Pd25 high-temperature shape memory alloy (HTSMA) is microalloyed with 0.5 at. pct scandium (Sc) to enhance its shape-memory characteristics, in particular, dimensional stability under repeated thermomechanical cycles. For both Ti(50.5)Ni(24.5)Pd25 and the Sc-alloyed material, differential scanning calorimetry is conducted for multiple cycles to characterize cyclic stability of the transformation temperatures. The microstructure is evaluated using electron microscopy, X-ray diffractometry, and wavelength dispersive spectroscopy. Isobaric thermal cycling experiments are used to determine transformation temperatures, dimensional stability, and work output as a function of stress. The Sc-doped alloy displays more stable shape memory response with smaller irrecoverable strain and narrower thermal hysteresis than the baseline ternary alloy. This improvement in performance is attributed to the solid solution hardening effect of Sc.

  5. Irradiation creep of vanadium-base alloys

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, H.; Billone, M.C.; Strain, R.V.; Smith, D.L. [Argonne National Lab., IL (United States); Matsui, H. [Tohoku Univ. (Japan)

    1998-03-01

    A study of irradiation creep in vanadium-base alloys is underway with experiments in the Advanced Test Reactor (ATR) and the High Flux Isotope Reactor (HFIR) in the United States. Test specimens are thin-wall sealed tubes with internal pressure loading. The results from the initial ATR irradiation at low temperature (200--300 C) to a neutron damage level of 4.7 dpa show creep rates ranging from {approx}0 to 1.2 {times} 10{sup {minus}5}/dpa/MPa for a 500-kg heat of V-4Cr-4Ti alloy. These rates were generally lower than reported from a previous experiment in BR-10. Because both the attained neutron damage levels and the creep strains were low in the present study, however, these creep rates should be regarded as only preliminary. Substantially more testing is required before a data base on irradiation creep of vanadium alloys can be developed and used with confidence.

  6. 21 CFR 872.3710 - Base metal alloy.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Base metal alloy. 872.3710 Section 872.3710 Food... DEVICES DENTAL DEVICES Prosthetic Devices § 872.3710 Base metal alloy. (a) Identification. A base metal alloy is a device composed primarily of base metals, such as nickel, chromium, or cobalt, that...

  7. Electrolytic Passivation of Nitinol Shape Memory Alloy in Different Electrolytes

    Institute of Scientific and Technical Information of China (English)

    SU Xiang-dong; WANG Tian-min; HAO Wei-chang; HE Li

    2006-01-01

    The corrosion behavior of the nitinol alloy was studied in various corrosion media of different Cl- ion concentrations. The results demonstrate that the Cl- ion concentration has significant influences on the corrosion behavior of the nitinol alloy. In order to enhance the corrosion resistance, protective films were generated on the surface of the nitinol alloy by means of the electrochemical passivation method, for which five different electrolytic solutions were investigated. The surface analysis indicates full growth of all samples passivated in the different electrolytic solutions with layers, however, showing different morphological features. Without any defects like micro-cracks and pores, the surface of the samples passivated in the molybdate solution turns out smoother and denser than those passivated in other solutions. It is shown that the electro-chemical passivation will reduce Ni content but increase Ti content in the surface, reaching the Mole ratio of Ti:Ni = 9.01:1 on the outermost surface. Potentiodynamic polarization test demonstrates that the samples electrochemically passivated in the molybdate solution present a significant increase in breakdown potential due to titanium enrichment on the outermost surface.

  8. Resistive content addressable memory based in-memory computation architecture

    KAUST Repository

    Salama, Khaled N.

    2016-12-08

    Various examples are provided examples related to resistive content addressable memory (RCAM) based in-memory computation architectures. In one example, a system includes a content addressable memory (CAM) including an array of cells having a memristor based crossbar and an interconnection switch matrix having a gateless memristor array, which is coupled to an output of the CAM. In another example, a method, includes comparing activated bit values stored a key register with corresponding bit values in a row of a CAM, setting a tag bit value to indicate that the activated bit values match the corresponding bit values, and writing masked key bit values to corresponding bit locations in the row of the CAM based on the tag bit value.

  9. Temperature dependent fracture properties of shape memory alloys: novel findings and a comprehensive model.

    Science.gov (United States)

    Maletta, Carmine; Sgambitterra, Emanuele; Niccoli, Fabrizio

    2016-12-21

    Temperature dependent fracture properties of NiTi-based Shape Memory Alloys (SMAs), within the pseudoelastic regime, were analyzed. In particular, the effective Stress Intensity Factor (SIF) was estimated, at different values of the testing temperature, by a fitting of the William's expansion series, based on Digital Image Correlation (DIC) measurements. It was found that temperature plays an important role on SIF and on critical fast fracture conditions. As a consequence, Linear Elastic Fracture Mechanics (LEFM) approaches are not suitable to predict fracture properties of SMAs, as they do not consider the effects of temperature. On the contrary, good agreements between DIC results and the predictions of an ad-hoc analytical model were observed. In fact, the model takes into account the whole thermo mechanical loading condition, including both mechanical load and temperature. Results revealed that crack tip stress-induced transformations do not represent a toughening effect and this is a completely novel result within the SMA community. Furthremore, it was demonstrated that the analytical model can be actually used to define a temperature independent fracture toughness parameter. Therefore, a new approach is proposed, based on the analytical model, where both mechanical load and temperature are considered as loading parameters in SIF computation.

  10. Investigations of binary and ternary phase change alloys for future memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Rausch, Pascal

    2012-09-13

    The understanding of phase change materials is of great importance because it enables us to predict properties and tailor alloys which might be even better suitable to tackle challenges of future memory applications. Within this thesis two topics have been approached: on the one hand the understanding of the alloy In{sub 3}Sb{sub 1}Te{sub 2} and on the other hand the so called resistivity drift of amorphous Ge-Sn-Te phase change materials. The main topic covers an in depth discussion of the ternary alloy In{sub 3}Sb{sub 1}Te{sub 2}. At first glance, this alloy does not fit into the established concepts of phase alloys: e.g. the existence of resonant bonding in the crystalline phase is not obvious and the number of p-electrons is very low compared to other phase change alloys. Furthermore amorphous phase change alloys with high indium content are usually not discussed in literature, an exception being the recent work by Spreafico et al. on InGeTe{sub 2}. For the first time a complete description of In{sub 3}Sb{sub 1}Te{sub 2} alloy is given in this work for the crystalline phase, amorphous phase and crystallization process. In addition comparisons are drawn to typical phase change materials like Ge{sub 2}Sb{sub 2}Te{sub 5}/GeTe or prototype systems like AgInTe{sub 2} and InTe. The second topic of this thesis deals with the issue of resistivity drift, i.e. the increase of resistivity of amorphous phase change alloys with aging. This drift effect greatly hampers the introduction of multilevel phase change memory devices into the market. Recently a systematic decrease of drift coefficient with stoichiometry has been observed in our group going from GeTe over Ge{sub 3}Sn{sub 1}Te{sub 4} to Ge{sub 2}Sn{sub 2}Te{sub 4}. These alloys are investigated with respect to constraint theory.

  11. In vitro corrosion behaviour of Ti-Nb-Sn shape memory alloys in Ringer's physiological solution.

    Science.gov (United States)

    Rosalbino, F; Macciò, D; Scavino, G; Saccone, A

    2012-04-01

    The nearly equiatomic Ni-Ti alloy (Nitinol) has been widely employed in the medical and dental fields owing to its shape memory or superelastic properties. The main concern about the use of this alloy derives form the fact that it contains a large amount of nickel (55% by mass), which is suspected responsible for allergic, toxic and carcinogenic reactions. In this work, the in vitro corrosion behavior of two Ti-Nb-Sn shape memory alloys, Ti-16Nb-5Sn and Ti-18Nb-4Sn (mass%) has been investigated and compared with that of Nitinol. The in vitro corrosion resistance was assessed in naturally aerated Ringer's physiological solution at 37°C by corrosion potential and electrochemical impedance spectroscopy (EIS) measurements as a function of exposure time, and potentiodynamic polarization curves. Corrosion potential values indicated that both Ni-Ti and Ti-Nb-Sn alloys undergo spontaneous passivation due to spontaneously formed oxide film passivating the metallic surface, in the aggressive environment. It also indicated that the tendency for the formation of a spontaneous oxide is greater for the Ti-18Nb-5Sn alloy. Significantly low anodic current density values were obtained from the polarization curves, indicating a typical passive behaviour for all investigated alloys, but Nitinol exhibited breakdown of passivity at potentials above approximately 450 mV(SCE), suggesting lower corrosion protection characteristics of its oxide film compared to the Ti-Nb-Sn alloys. EIS studies showed high impedance values for all samples, increasing with exposure time, indicating an improvement in corrosion resistance of the spontaneous oxide film. The obtained EIS spectra were analyzed using an equivalent electrical circuit representing a duplex structure oxide film, composed by an outer and porous layer (low resistance), and an inner barrier layer (high resistance) mainly responsible for the alloys corrosion resistance. The resistance of passive film present on the metals' surface

  12. LOW VELOCITY RESPONSE CHARACTERISTICS OF COMPOSITE PLATE WITH EMBEDDED SHAPE MEMORY ALLOY

    Institute of Scientific and Technical Information of China (English)

    WuYongdong; ZhongWeifang; LiangYide

    2004-01-01

    This paper analyzes the characteristics of utilizing shape memory effect (SME) of shape memory alloy (SMA) in improving the low velocity impact resistance performance of composite plate by using finite element method. The constitutive relation for SMA hybrid composite plates is presented. The analytic model of finite element for SMA composite plate subjected to low velocity impact is established. The modified Hertz's contact law is used to determine the impact contact force. The computing procedures for solving the finite element equation using Newmark direct integration method are given. The numerical modelling results show that the SMA can effectively improve the low velocity impact resistance performance of composite plate.

  13. Experimental Study on Characteristics of NiMnGa Magnetically Controlled Shape Memory Alloy

    Institute of Scientific and Technical Information of China (English)

    Fengxiang WANG; Wenjun LI; Qingxin ZHANG; Chenxi LI; Xinjie WU

    2006-01-01

    The static and dynamic magnetic controlling characteristics of NiMnGa magnetically controlled shape memory alloy (MSMA) were experimentally studied. The results show that the characteristics of induced strain with respect to the magnetic field are nonlinear with saturation nature, and dependent on the temperature as well as the load applied to the MSMA. The magnetic shape memory effect can be observed only in complete martensite phase at room temperature. The magnetic permeability of MSMA is not constant and reduces with the increment of magnetic field. The relative saturation magnetic permeability of MSMA is about 1.5.

  14. Characteristics of Anodized Layer in Investment Cast Ni50Ti50 Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Shimaa H. El-Hadad

    2014-01-01

    Full Text Available NiTi shape memory alloys are promising implant materials due to their shape memory effect and super elasticity. In the current study, some Ni50Ti50 (mass % SMAs samples were prepared by investment casting. These samples were then anodized and thermally treated to improve the surface properties. A fully saturated oxide layer was obtained. The structure and hardness properties of the anodized surfaces were then investigated. A hard porous layer with no free Ni atoms could be obtained which can be used as prebiomimetic surface for biological application.

  15. Thermoelastic martensitic transformations, mechanical properties, and shape-memory effects in rapidly quenched Ni45Ti32Hf18Cu5 alloy in the ultrafine-grained state

    Science.gov (United States)

    Pushin, V. G.; Pushin, A. V.; Kuranova, N. N.; Kuntsevich, T. E.; Uksusnikov, A. N.; Dyakina, V. P.; Kourov, N. I.

    2016-12-01

    Methods of transmission and scanning electron microscopy and chemical microanalysis, electron diffraction, and X-ray diffraction were used to study the structure and the chemical and phase composition of ribbons of the four-component quasi-binary alloy Ni45Ti32Hf18Cu5. The influence of the synthesis regimes and subsequent heat treatment of the alloy on the formation of the amorphized state and ultrafine-grained structure has been determined. The critical temperatures of the devitrification and of the B2 ↔ B19' thermoelastic martensitic transformation have been established based on the data of the temperature dependences of the electrical resistivity. The lattice parameters of the B2 and B19' phases and the (Ti,Hf)2Ni phase have been determined by X-ray diffraction. The mechanical properties of the alloy were determined in tensile tests, and the shape-memory effects in the ribbons of the alloy were measured using bending tests.

  16. An Alternate to Cobalt-Base Hardfacing Alloys

    Science.gov (United States)

    Hickl, Anthony J.

    1980-03-01

    The price of cobalt has risen dramatically in the last few years, and supply has often been uncertain. The most popular hardfacing alloys contain substantial amounts of cobalt, and have thus been especially affected by these factors. The present study has developed a new hardfacing alloy, HAYNES Alloy No. 716, with lower cobalt content, to replace the most popular alloy, HAYNES STELLITE Alloy No. 6 which is cobalt based. The alloy design which led to the development of the new alloy is discussed, and properties are compared with Alloy No. 6. Hardness at room temperature and elevated temperatures, weldability, and corrosion and abrasion resistance of the new alloy compare favorably with Alloy No. 6.

  17. Nanoparticles from Cu-Zn-Al shape memory alloys physically synthesized by ion milling deposition

    Energy Technology Data Exchange (ETDEWEB)

    Pavon, Luis Alberto Lopez [Universidad Autonoma de Nuevo Leon (UANL), Nuevo Leon (Mexico); Cuellara, Enrique Lopez; Castro, Alejandro Torres; Cruza, Azael Martinez de la [Universidad Autonoma de Nuevo Leon (CIIDIT/UANL), Nuevo Leon (Mexico). Centro de Innovacion, Investigacion y Desarrollo en Ingenieria y Tecnologia; Ballesteros, Carmen [Universidad Carlos III de Madrid, Madrid (Spain). Departamento de Fisica; Araujo, Carlos Jose de [Universidade Federal de Campina Grande (UFCG), Campina Grande, PB (Brazil). Departamento de Engenharia Mecanica

    2012-05-15

    In this research, an ion milling equipment was used to elaborate nanoparticles from Cu-Zn-Al alloys with shape memory effect. Two different compositions were used, target A: 75.22Cu-17.12Zn-7.66Al at % with an Ms of -9 deg C and target B: 76.18Cu-15.84Zn-7.98Al with an Ms of 20 degree C. Nanoparticles were characterized by High Resolution Transmission Electron Microscopy, Electron Diffraction and Energy Dispersive X-ray Spectroscopy. The obtained nanoparticles showed a small dispersion, with a size range of 3.2-3.5 nm. Their crystal structure is in good agreement with the bulk martensitic structure of the targets. In this sense, results on morphology, composition and crystal structure have indicated that it is possible to produce nanoparticles of CuZnAl shape memory alloys with martensitic structure in a single process using Ion Milling. (author)

  18. Performance of Integrated Fiber Optic, Piezoelectric, and Shape Memory Alloy Actuators/Sensors in Thermoset Composites

    Science.gov (United States)

    Trottier, C. Michael

    1996-01-01

    Recently, scientists and engineers have investigated the advantages of smart materials and structures by including actuators in material systems for controlling and altering the response of structural environments. Applications of these materials systems include vibration suppression/isolation, precision positioning, damage detection and tunable devices. Some of the embedded materials being investigated for accomplishing these tasks include piezoelectric ceramics, shape memory alloys, and fiber optics. These materials have some benefits and some shortcomings; each is being studied for use in active material design in the SPICES (Synthesis and Processing of Intelligent Cost Effective Structures) Consortium. The focus of this paper concerns the manufacturing aspects of smart structures by incorporating piezoelectric ceramics, shape memory alloys and fiber optics in a reinforced thermoset matrix via resin transfer molding (RTM).

  19. Load carrying capacity of RCC beams by replacing steel reinforcement bars with shape memory alloy bars

    Science.gov (United States)

    Bajoria, Kamal M.; Kaduskar, Shreya S.

    2016-04-01

    In this paper the structural behavior of reinforced concrete (RC) beams with smart rebars under two point loading system has been numerically studied, using Finite Element Method. The material used in this study is Super-elastic Shape Memory Alloys (SE SMAs) which contains nickel and titanium. In this study, different quantities of steel and SMA rebars have been used for reinforcement and the behavior of these models under two point bending loading system is studied. A comparison of load carrying capacity for the model between steel reinforced concrete beam and the beam reinforced with S.M.A and steel are performed. The results show that RC beams reinforced with combination of shape memory alloy and steel show better performance.

  20. Attractors for a Three-Dimensional Thermo-Mechanical Model of Shape Memory Alloys

    Institute of Scientific and Technical Information of China (English)

    Pierluigi COLLI; Michel FR(E)MOND; Elisabetta ROCCA; Ken SHIRAKAWA

    2006-01-01

    In this note, we consider a Frémond model of shape memory alloys. Let us imagine a piece of a shape memory alloy which is fixed on one part of its boundary, and assume that forcing terms, e.g., heat sources and external stress on the remaining part of its boundary, converge to some time-independent functions, in appropriate senses, as time goes to infinity. Under the above assumption, we shall discuss the asymptotic stability for the dynamical system from the viewpoint of the global attractor. More precisely,we generalize the paper [12] dealing with the one-dimensional case. First, we show the existence of the global attractor for the limiting autonomous dynamical system; then we characterize the asymptotic stability for the non-autonomous case by the limiting global attractor.

  1. Design of a Shape Memory Alloy deployment hinge for reflector facets

    Science.gov (United States)

    Anders, W. S.; Rogers, C. A.

    1991-01-01

    A design concept for a Shape Memory Alloy (SMA) actuated hinge mechanism for deploying segmented facet-type reflector surfaces on antenna truss structures is presented. The mechanism uses nitinol, a nickel-titanium shape memory alloy, as a displacement-force micro-actuator. An electrical current is used to resistively heat a 'plastically' elongated SMA actuator wire, causing it to contract in response to a thermally-induced phase transformation. The resulting tension creates a moment, imparting rotary motion between two adjacent panels. Mechanical stops are designed into the device to limit its range of motion and to establish positioning accuracy at the termination of deployment. The concept and its operation are discussed in detail, and an analytical dynamic simulation model is presented. The model has been used to perform nondimensionalized parametric design studies.

  2. Investigation on actuation and thermo-mechanical behaviour of Shape Memory Alloy spring using hot water

    Science.gov (United States)

    Chouhan, Priya; Nath, Tameshwer; Lad, B. K.; Palani, I. A.

    2016-09-01

    In this paper, hot water is used as an actuation media for Shape memory alloy and its impact on the morphology of structure of Nitinol Shape Memory Alloy (SMA), is presented. With hot water actuation as the temperature reaches 70-80°C, spring gets fully compressed for the first few cycles followed by a displacement loss in actuation. This actuation loss is then studied with different characterization methods such as Thermo Gravimetric Analysis (TGA) and Scanning Electron Microscopy (SEM). With SEM results, it can be inferred that the energy source is not deteriorating the structure. Results observed from TGA shows high oxygen content at lower temperature limits with hot water actuation which suggest the need of conducting experiments in inert atmosphere. As a possible mechanism, a new actuation medium is introduced and various results can be seen in the paper discussed below.

  3. [Design and biomechanical analysis of nickel-titanium open shape memory alloy artificial vertebral body].

    Science.gov (United States)

    Liu, Hui; Lian, Kejian; Liao, Lijun; Zhai, Wenliang; Ding, Zhenqi

    2010-10-01

    To design an open shape memory alloy artificial vertebral body that can be used to reconstruct the vertebral body in spine diseases, such as thoracic-lumbar spine tumors, burst fracture of the vertebrae, kyphosis and scoliosis, and to evaluate the biomechanical stability of lumbar functional segment unit after insertion with the shape memory alloy artificial vertebral body. The open shape memory alloy artificial vertebral body with nickel-titanium (NiTi) alloy was made. Eight fresh spine specimens (T14-L5) from normal adult porcine were used to detect the range of motion (ROM) in 4 models and were divided into 4 groups: intact vertebrae served as group A; pedicle screw fixation of T15, L1, L3, and L4 was given in group B; after total resection of L2, it was reconstructed by open shape memory alloy artificial vertebral body combined with pedicle screw fixation of T15, L1, L3, and L4 in group C; and after total resection of L2, it was reconstructed by titanium cage vertebral body combined with pedicle screw fixation of T15, L1, L3, and L4 in group D. The three-dimensional ROM of flexion, extension, left/right lateral bending, and left/right rotation in T15-L1, L1-3, and L3,4 segments were detected in turn by the spinal three-dimensional test machine MTS-858 (load 0-8 N x m). Compared with group A, groups B, C, and D had good stability in flexion, extension, left/right lateral bending, and left/right rotation, showing significant differences (P 0.05). Group C had less degree of motion in T15-L1 and L3,4 segments than group D, showing significant differences (P 0.05). The open shape memory alloy artificial vertebral body has a reasonable structure and good biomechanical stability, it can be used to stabilize the spinal segment with pedicle screw fixation.

  4. Self-Repairing Fatigue Damage in Metallic Structures for Aerospace Vehicles Using Shape Memory Alloy Self-healing (SMASH) Technology

    Science.gov (United States)

    Wright, M. Clara; Manuel, Michele; Wallace, Terryl; Newman, Andy; Brinson, Kate

    2015-01-01

    This DAA is for the Phase II webinar presentation of the ARMD-funded SMASH technology. A self-repairing aluminum-based composite system has been developed using liquid-assisted healing theory in conjunction with the shape memory effect of wire reinforcements. The metal matrix composite was thermodynamically designed to have a matrix with a relatively even dispersion of low-melting phase, allowing for repair of cracks at a pre-determined temperature. Shape memory alloy wire reinforcements were used within the composite to provide crack closure. Investigators focused the research on fatigue cracks propagating through the matrix in order to optimize and computer model the SMASH technology for aeronautical applications.

  5. Assessment of Shape Memory Alloys - From Atoms To Actuators - Via In Situ Neutron Diffraction

    Science.gov (United States)

    Benafan, Othmane

    2014-01-01

    As shape memory alloys (SMAs) become an established actuator technology, it is important to identify the fundamental mechanisms responsible for their performance by understanding microstructure performance relationships from processing to final form. Yet, microstructural examination of SMAs at stress and temperature is often a challenge since structural changes occur with stress and temperature and microstructures cannot be preserved through quenching or after stress removal, as would be the case for conventional materials. One solution to this dilemma is in situ neutron diffraction, which has been applied to the investigation of SMAs and has offered a unique approach to reveal the fundamental micromechanics and microstructural aspects of bulk SMAs in a non-destructive setting. Through this technique, it is possible to directly correlate the micromechanical responses (e.g., internal residual stresses, lattice strains), microstructural evolutions (e.g., texture, defects) and phase transformation properties (e.g., phase fractions, kinetics) to the macroscopic actuator behavior. In this work, in situ neutron diffraction was systematically employed to evaluate the deformation and transformation behavior of SMAs under typical actuator conditions. Austenite and martensite phases, yield behavior, variant selection and transformation temperatures were characterized for a polycrystalline NiTi (49.9 at. Ni). As the alloy transforms under thermomechanical loading, the measured textures and lattice plane-level variations were directly related to the cyclic actuation-strain characteristics and the dimensional instability (strain ratcheting) commonly observed in this alloy. The effect of training on the shape memory characteristics of the alloy and the development of two-way shape memory effect (TWSME) were also assessed. The final conversion from a material to a useful actuator, typically termed shape setting, was also investigated in situ during constrained heatingcooling and

  6. Effect of selenium addition on the GeTe phase change memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Vinod, E.M., E-mail: vinuem@gmail.com [Department of Physics, Indian Institute of Science, Bangalore 560 012 (India); Singh, A.K.; Ganesan, R. [Department of Physics, Indian Institute of Science, Bangalore 560 012 (India); Sangunni, K.S., E-mail: sangu@physics.iisc.ernet.in [Department of Physics, Indian Institute of Science, Bangalore 560 012 (India)

    2012-10-05

    Highlights: Black-Right-Pointing-Pointer Selenium is used as an additive to GeTe phase change materials. Black-Right-Pointing-Pointer Crystalline structure of GeTe alloys does not affect up to 0.20 at.% of Se. Black-Right-Pointing-Pointer The possibility of Se occupying Ge vacancy sites in GeTe structure is explained. Black-Right-Pointing-Pointer Ge-Se and GeTe{sub 2} bonds increase with increase of Se concentration. Black-Right-Pointing-Pointer T{sub m} is reduced in 0.50 at.% Se alloy, which can reduce RESET current requirements. - Abstract: Compositional dependent investigations of the bulk GeTe chalcogenides alloys added with different selenium concentrations are carried out by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), electron probe micro-analyzer (EPMA) and differential scanning calorimetry (DSC). The measurements reveal that GeTe crystals are predominant in alloys up to 0.20 at.% of Se content indicating interstitial occupancy of Se in the Ge vacancies. Raman modes in the GeTe alloys changes to GeSe modes with the addition of Se. Amorphousness in the alloy increases with increase of Se and 0.50 at.% Se alloy forms a homogeneous amorphous phase with a mixture of Ge-Se and Te-Se bonds. Structural changes are explained with the help of bond theory of solids. Crystallization temperature is found to be increasing with increase of Se, which will enable the amorphous stability. For the optimum 0.50 at.% Se alloy, the melting temperature has reduced which will reduce the RESET current requirement for the phase change memory applications.

  7. TEM observation of oxidation of CuZnAlMnNi shape memory alloy

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The atmospheric oxidation of a quenched CuZnAlMnNi alloy after ion-polishing was examined by transmission electron microscopy (TEM). It was found that a lot of oxide grains with various sizes yield homogeneously on the surface of the alloy after exposure at room temperature for 90 d. The grains mainly form along the planes of stacking fault, meanwhile, they can also be observed at the stacking fault tetrahedrals or around the dislocation lines. The formarion of the oxides gives rise to the reduction of the stacking faults, and even complete disappearance in some zones,which is partly responsible for the decrement of shape memory. effect (SME) of the alloy quenched during long-term holding at room temperature.

  8. Investigation on microstructure and martensitic transformation of neodymium-added NiTi shape memory alloys

    Science.gov (United States)

    Maashaa, Dovchinvanchig; Dorj, Ulzii-Orshikh; Lee, Malrey; Lee, Min Hi; Zhao, Chunwang; Dashjav, Munguntsetseg; Woo, Seon-Mi

    2016-10-01

    The effect of rare earth element neodymium (Nd) addition on the microstructure and martensitic transformation behavior of Ni50Ti50-xNdx (x = 0, 0.1, 0.3, 0.5 and 0.7 at.%) shape memory alloy was investigated by scanning electronic microscope, X-ray diffraction and differential scanning calorimetry. The results show that the microstructure of Ni-Ti-Nd ternary alloy consists of NiNd phase, NiTi2 and the NiTi matrix. A one-step martensitic transformation is observed in the alloys. The martensitic transformation temperature Ms increases sharply increasing 0.1-0.7 at.% Nd content is added.

  9. Characterization of Polylactide Layer Deposited on Ni-Ti Shape Memory Alloy

    Science.gov (United States)

    Goryczka, Tomasz; Szaraniec, Barbara

    2014-07-01

    Polylactide (PLA) thin layer was deposited on the surface of the as-quenched NiTi shape memory alloy. First, NiTi alloy was quenched from the 850°C, then its surface was covered with PLA. Deposited PLA is in an amorphous state, whereas the as-quenched NiTi alloy stays in the B2 structure. PLA deposition caused smoothing of the surface and changed its hydrophilic character to hydrophobic one. In general, procedure of PLA deposition does not influence the course of the reversible martensitic transformation. After deformation of NiTi sample covered with PLA up to 4%, its surface does not reveal any cracks and still remains continuous.

  10. Thermo-mechanical response and fatigue behavior of shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Kusagawa, Masaki; Asada, Yasuhide; Nakamura, Toshiya [Tokyo Univ. (Japan). Dept. of Mechanical Engineering

    1998-11-01

    Mechanical, thermo-mechanical and fatigue behaviors of Ni-Ti-Nb shape memory alloy (SMA) have been studied to prepare material data for a design purpose. Presented are testing devices, testing procedure and test results of monotonic tensile, recovery of inelastic deformation due to post heating (thermo-mechanical recovery) and fatigue for future use of the SMA as a structural material of nuclear incore structures. (orig.)

  11. Influence of crystalline orientation on the thermal-energy convertion efficiency in shape memory alloys

    Directory of Open Access Journals (Sweden)

    Cortés-Pérez J.

    2014-01-01

    Full Text Available A theoretical study about the influence of crystalline orientation on the energy conversion efficiency of two shape memory alloys is present. The study consider single crystal samples in simple tension. The results showed higher properties for of the NiTi than Cu-Al-Be, especially in the temperature-increment (ΔT necessary for get a conversion energy cycle. However, the study showed a crystalline orientation favorable for Cu-Al-Be.

  12. Deposition of Chitosan Layers on NiTi Shape Memory Alloy

    Directory of Open Access Journals (Sweden)

    Kowalski P.

    2015-04-01

    Full Text Available The NiTi shape memory alloys have been known from their application in medicine for implants as well as parts of medical devices. However, nickel belongs to the family of elements, which are toxic. Apart from the fact that nickel ions are bonded with titanium into intermetallic phase, their presence may cause allergy. In order to protect human body against release of nickel ions a surface of NiTi alloy can be modified with use of titanium nitrides, oxides or diamond-like layers. On the one hand the layers can play protective role but on the other hand they may influence shape memory behavior. Too stiff or too brittle layer can lead to limiting or completely blocking of the shape recovery. It was the reason to find more elastic covers for NiTi surface protection. This feature is characteristic for polymers, especially, biocompatible ones, which originate in nature. In the reported paper, the chitosan was applied as a deposited layer on surface of the NiTi shape memory alloy. Due to the fact that nature of shape memory effect is sensitive to thermo and/or mechanical treatments, the chitosan layer was deposited with use of electrophoresis carried out at room temperature. Various deposition parameters were checked and optimized. In result of that thin chitosan layer (0.45µm was received on the NiTi alloy surface. The obtained layers were characterized by means of chemical and phase composition, as well as surface quality. It was found that smooth, elastic surface without cracks and/or inclusions can be produced applying 10V and relatively short deposition time - 30 seconds.

  13. Contribution of Shape Memory Alloys Elements in Designing Underwater Smart Structures

    Directory of Open Access Journals (Sweden)

    Daniel Amariei

    2007-10-01

    Full Text Available Shape memory alloys (SMA have generated a lot of new ideas in engineering. Application is however so far limited to clamps and springs. With respect to smart structures sensing as well as control has to be included. While sensing looks to be relatively feasible control is the big challenge. This paper describes some related a smart structure idea using SMAs and discusses the challenges which need to be solved before these ideas can be realised.

  14. Surface Characterization of Laser Surface Melted NiTi Shape Memory Alloy in Hanks' Solution

    Institute of Scientific and Technical Information of China (English)

    CUIZhen-duo; ZHUSheng-li; MANHauchung; YANGXian-jin

    2004-01-01

    The surface of Ti-50.8Ni at% shape memory alloy was melted by an Nd-YAG laser. The Ti/Ni and Ti4+/ Tiatomic concentration ratios at the surface were changed significantly. The Ni ion release rate of the laser melted surface was much lower than that of the mechanical polished samples. A calcium-phosphorous layer with high Ca/P ratio was detected after immersion in Hanks' solution.

  15. Surface Characterization of Laser Surface Melted NiTi Shape Memory Alloy in Hanks' Solution

    Institute of Scientific and Technical Information of China (English)

    CUI Zhen-duo; ZHU Sheng-li; MAN Hauchung; YANG Xian-jin

    2004-01-01

    The surface of Ti-50.8Ni at% shape memory alloy was melted by an Nd-YAG laser. The Ti/Ni and Ti4+/Ti atomic concentration ratios at the surface were changed significantly. The Ni ion release rate of the laser melted surface was much lower than that of the mechanical polished samples. A calcium-phosphorous layer with high Ca/P ratio was detected after immersion in Hanks' solution.

  16. Thermomechanical Modeling of Shape Memory Alloys with Rate Dependency on the Pseudoelastic Behavior

    Directory of Open Access Journals (Sweden)

    Jin-Ho Roh

    2014-01-01

    Full Text Available The loading-rate dependency on the pseudoelastic behaviors of shape memory alloy (SMA wires is experimentally and numerically investigated. The results are analyzed to estimate the parameters for a thermomechanical constitutive model of SMA wire with strain-rate dependency of the hysteresis behavior. An analytical model of SMAs is developed by using nonconstant parameters during various strain rates. Numerical simulations are performed to demonstrate the accuracy of the improved model.

  17. Preparation of NiFe binary alloy nanocrystals for nonvolatile memory applications

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this work,an idea which applies binary alloy nanocrystal floating gate to nonvolatile memory application was introduced.The relationship between binary alloy’s work function and its composition was discussed theoretically.A nanocrystal floating gate structure with NiFe nanocrystals embedded in SiO2 dielectric layers was fabricated by magnetron sputtering.The micro-structure and composition deviation of the prepared NiFe nanocrystals were also investigated by TEM and EDS.

  18. Low Velocity Impact Response Analysis of Shape Memory Alloy Reinforced Composite Beam

    Institute of Scientific and Technical Information of China (English)

    WU Yongdong; ZHONG Weifang; WU Guorong; ZOU Jing

    2005-01-01

    The low velocity impact responses of shape memory alloy ( SMA ) reinforced composite beams were analyzed by employing the finite element method. The finite element dynamic equation was solved by the Newmark direct integration method, the impact contact force was determined using the Hertzian contact law, and the influence of SMA fibers on stiffness matrix is studied. Numerical results show that the SMA fibers can effectively improve the low velocity impact response property of composite beam.

  19. Phase transformation behavior of a TiNiCu shape memory alloy electrolytically charged with hydrogen

    Institute of Scientific and Technical Information of China (English)

    WU Jihong; ZU Xiaotao; WANG Zhiguo; LIU Yanzhang

    2005-01-01

    The transformation behavior of a TiNiCu shape memory alloy electrolytically charged with hydrogen was investigated by means of different scanning calorimetry (DSC), optical microscope and X-ray diffraction (XRD). The results showed that inter- and inner-granular hydrides formed after charging with hydrogen, and the hydrides suppressed martensitic transformation. The electrolytically charged hydrogen can be easily released by heat treatment and the transformation occurred again, which was verified by the DSC and XRD experiments.

  20. Effect of tellurium on machinability and mechanical property of CuAlMnZn shape memory alloy

    Energy Technology Data Exchange (ETDEWEB)

    Liu Na [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Li Zhou, E-mail: lizhou6931@csu.edu.cn [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China); Key Laboratory of Nonferrous Metal Materials Science and Engineering, Ministry of Education, Changsha, 410083 (China); Xu Genying; Feng Ze; Gong Shu; Zhu Lilong; Liang Shuquan [School of Materials Science and Engineering, Central South University, Changsha, 410083 (China)

    2011-10-15

    Highlights: {yields} A novel free-machining Cu-7.5Al-9.7Mn-3.4Zn-0.3Te (wt.%) shape memory alloy has been developed. {yields} The size of dispersed particles with richer Te is 2-5 {mu}m. {yields} The CuAlMnZnTe alloy has good machinability which approached that of BZn15-24-1.5 due to the addition of Te. {yields} Its shape memory property keeps the same as that of CuAlMnZn alloy with free Te. {yields} The CuAlMnZn shape memory alloy with and without Te both have good ductile as annealed at 700 deg. C for 15 min. - Abstract: The microstructure transition, shape memory effect, machinability and mechanical property of the CuAlMnZn alloy with and without Te have been studied using X-ray diffraction analysis, chips observation and scanning electron microscopy (SEM), tensile strength test and differential scanning calorimeter (DSC), and semi-quantitative shape memory effect (SME) test. The particles with richer Te dispersedly distributed in grain interior and boundary with size of 2-5 {mu}m. After the addition of Te, the CuAlMnZnTe alloy machinability has been effectively increased to approach that of BZn15-24-1.5 and its shape memory property remains the same as the one of CuAlMnZn alloy. The CuAlMnZn shape memory alloys with and without Te both have good ductility as annealed at 700 deg. C for 15 min.

  1. Reversible Martensitic Transformation under Low Magnetic Fields in Magnetic Shape Memory Alloys

    Science.gov (United States)

    Bruno, N. M.; Wang, S.; Karaman, I.; Chumlyakov, Y. I.

    2017-01-01

    Magnetic field-induced, reversible martensitic transformations in NiCoMnIn meta-magnetic shape memory alloys were studied under constant and varying mechanical loads to understand the role of coupled magneto-mechanical loading on the transformation characteristics and the magnetic field levels required for reversible phase transformations. The samples with two distinct microstructures were tested along the [001] austenite crystallographic direction using a custom designed magneto-thermo-mechanical characterization device while carefully controlling their thermodynamic states through isothermal constant stress and stress-varying magnetic field ramping. Measurements revealed that these meta-magnetic shape memory alloys were capable of generating entropy changes of 14 J kg−1 K−1 or 22 J kg −1 K−1, and corresponding magnetocaloric cooling with reversible shape changes as high as 5.6% under only 1.3 T, or 3 T applied magnetic fields, respectively. Thus, we demonstrate that this alloy is suitable as an active component in near room temperature devices, such as magnetocaloric regenerators, and that the field levels generated by permanent magnets can be sufficient to completely transform the alloy between its martensitic and austenitic states if the loading sequence developed, herein, is employed. PMID:28091551

  2. The response of macrophages to a Cu-Al-Ni shape memory alloy.

    Science.gov (United States)

    Colić, Miodrag; Tomić, Sergej; Rudolf, Rebeka; Anzel, Ivan; Lojen, Gorazd

    2010-09-01

    Cu-Al-Ni shape memory alloys (SMAs) have been investigated as materials for medical devices, but little is known about their biocompatibility. The aim of this work was to study the response of rat peritoneal macrophages (PMØ) to a Cu-Al-Ni SMA in vitro, by measuring the functional activity of mitochondria, necrosis, apoptosis, and production of proinflammatory cytokines. Rapidly solidified (RS) thin ribbons were used for the tests. The control alloy was a permanent mold casting of the same composition, but without the shape memory effect. Our results showed that the control alloy was severely cytotoxic, whereas RS ribbons induced neither necrosis nor apoptosis of PMØ. These findings correlated with the data that RS ribbons are significantly more resistant to corrosion compared to the control alloy, as judged by the lesser release of Cu and Ni in the conditioning medium. However, the ribbons generated intracellular reactive oxygen species and upregulated the production of IL-6 by PMØ. These effects were almost completely abolished by conditioning the RS ribbons for 5 weeks. In conclusion, RS significantly improves the corrosion stability and biocompatibility of Cu-Al-Ni SMA. The biocompatibility of this functional material could be additionally enhanced by conditioning the ribbons in cell culture medium.

  3. Reversible Martensitic Transformation under Low Magnetic Fields in Magnetic Shape Memory Alloys.

    Science.gov (United States)

    Bruno, N M; Wang, S; Karaman, I; Chumlyakov, Y I

    2017-01-16

    Magnetic field-induced, reversible martensitic transformations in NiCoMnIn meta-magnetic shape memory alloys were studied under constant and varying mechanical loads to understand the role of coupled magneto-mechanical loading on the transformation characteristics and the magnetic field levels required for reversible phase transformations. The samples with two distinct microstructures were tested along the [001] austenite crystallographic direction using a custom designed magneto-thermo-mechanical characterization device while carefully controlling their thermodynamic states through isothermal constant stress and stress-varying magnetic field ramping. Measurements revealed that these meta-magnetic shape memory alloys were capable of generating entropy changes of 14 J kg(-1) K(-1) or 22 J kg (-1) K(-1), and corresponding magnetocaloric cooling with reversible shape changes as high as 5.6% under only 1.3 T, or 3 T applied magnetic fields, respectively. Thus, we demonstrate that this alloy is suitable as an active component in near room temperature devices, such as magnetocaloric regenerators, and that the field levels generated by permanent magnets can be sufficient to completely transform the alloy between its martensitic and austenitic states if the loading sequence developed, herein, is employed.

  4. Reversible Martensitic Transformation under Low Magnetic Fields in Magnetic Shape Memory Alloys

    Science.gov (United States)

    Bruno, N. M.; Wang, S.; Karaman, I.; Chumlyakov, Y. I.

    2017-01-01

    Magnetic field-induced, reversible martensitic transformations in NiCoMnIn meta-magnetic shape memory alloys were studied under constant and varying mechanical loads to understand the role of coupled magneto-mechanical loading on the transformation characteristics and the magnetic field levels required for reversible phase transformations. The samples with two distinct microstructures were tested along the [001] austenite crystallographic direction using a custom designed magneto-thermo-mechanical characterization device while carefully controlling their thermodynamic states through isothermal constant stress and stress-varying magnetic field ramping. Measurements revealed that these meta-magnetic shape memory alloys were capable of generating entropy changes of 14 J kg-1 K-1 or 22 J kg -1 K-1, and corresponding magnetocaloric cooling with reversible shape changes as high as 5.6% under only 1.3 T, or 3 T applied magnetic fields, respectively. Thus, we demonstrate that this alloy is suitable as an active component in near room temperature devices, such as magnetocaloric regenerators, and that the field levels generated by permanent magnets can be sufficient to completely transform the alloy between its martensitic and austenitic states if the loading sequence developed, herein, is employed.

  5. Relationship between microstructure, cytotoxicity and corrosion properties of a Cu-Al-Ni shape memory alloy.

    Science.gov (United States)

    Colić, Miodrag; Rudolf, Rebeka; Stamenković, Dragoslav; Anzel, Ivan; Vucević, Dragana; Jenko, Monika; Lazić, Vojkan; Lojen, Gorazd

    2010-01-01

    Cu-Al-Ni shape memory alloys (SMAs) have been investigated as materials for medical devices, but their biomedical application is still limited. The aim of this work was to compare the microstructure, corrosion and cytotoxicity in vitro of a Cu-Al-Ni SMA. Rapidly solidified (RS) thin ribbons, manufactured via melt spinning, were used for the tests. The control alloy was a permanent mould casting of the same composition, but without shape memory effect. The results show that RS ribbons are significantly more resistant to corrosion compared with the control alloy, as judged by the lesser release of Cu and Ni into the conditioning medium. These results correlate with the finding that RS ribbons were not cytotoxic to L929 mouse fibroblasts and rat thymocytes. In addition, the RS ribbon conditioning medium inhibited cellular proliferation and IL-2 production by activated rat splenocytes to a much lesser extent. The inhibitory effects were almost completely abolished by conditioning the RS ribbons in culture medium for 4 weeks. Microstructural analysis showed that RS ribbons are martensitic, with boron particles as a minor phase. In contrast, the control Cu-Al-Ni alloy had a complex multiphase microstructure. Examination of the alloy surfaces after conditioning by energy dispersive X-ray and Auger electron spectroscopy showed the formation of Cu and Al oxide layers and confirmed that the metals in RS ribbons are less susceptible to oxidation and corrosion compared with the control alloy. In conclusion, these results suggest that rapid solidification significantly improves the corrosion stability and biocompatibility in vitro of Cu-Al-Ni SMA ribbons.

  6. An Introduction to a Porous Shape Memory Alloy Dynamic Data Driven Application System

    KAUST Repository

    Douglas, Craig C.

    2012-06-02

    Shape Memory Alloys are capable of changing their crystallographic structure due to changes of temperature and/or stress. Our research focuses on three points: (1) Iterative Homogenization of Porous SMAs: Development of a Multiscale Model of porous SMAs utilizing iterative homogenization and based on existing knowledge of constitutive modeling of polycrystalline SMAs. (2) DDDAS: Develop tools to turn on and off the sensors and heating unit(s), to monitor on-line data streams, to change scales based on incoming data, and to control what type of data is generated. The application must have the capability to be run and steered remotely. (3) Modeling and applications of porous SMA: Vibration isolation devices with SMA and porous SMA components for aerospace applications will be analyzed and tested. Numerical tools for modeling porous SMAs with a second viscous phase will be developed.The outcome will be a robust, three-dimensional, multiscale model of porous SMA that can be used in complicated, real-life structural analysis of SMA components using a DDDAS framework.

  7. A stabilized, high stress self-biasing shape memory alloy actuator

    Science.gov (United States)

    Panton, B.; Zhou, Y. N.; Khan, M. I.

    2016-09-01

    A shape memory alloy (SMA) actuator that is biased internally would not need an external bias to achieve multiple actuation cycles. This would reduce cost, complexity and weight compared to standard one-way SMAs. The self-biasing actuators that have been developed to date have a lack of geometric and actuation stability. The current study developed a self-biasing NiTi actuator using a laser based vaporization process to alter the bulk composition of different regions. The martensitic laser processed NiTi region was the actuator, and un-processed austenitic base metal region was the internal bias. It was discovered that the laser processed region of the self-biasing actuator was unstable during high stress thermomechanical cycling due to the coarse grained microstructure. Cold-working of the half martensitic and half austenitic component resulted in similar deformation characteristics to single phase NiTi, which enabled the formation of a uniform nanocrystalline microstructure in both regions. When thermomechanically cycled 6000 times under stresses ranging from 180 to 400 MPa, it was discovered that this treated self-biasing actuator exhibited the stabilization behavior of traditional one-way actuators. This behavior was due to the uniform nanocrystalline microstructure, which impeded dislocation activity and ensured minimal plastic deformation.

  8. Hysteresis Curve Fitting Optimization of Magnetic Controlled Shape Memory Alloy Actuator

    Directory of Open Access Journals (Sweden)

    Fuquan Tu

    2016-11-01

    Full Text Available As a new actuating material, magnetic controlled shape memory alloys (MSMAs have excellent characteristics such as a large output strain, fast response, and high energy density. These excellent characteristics are very attractive for precision positioning systems. However, the availability of MSMAs in practical precision positioning is poor, caused by weak repeatability under a certain stimulus. This problem results from the error of a large magnetic hysteresis in an external magnetic field. A suitable hysteresis modelling method can reduce the error and improve the accuracy of the MSMA actuator. After analyzing the original hysteresis modelling methods, three kinds of hysteresis modelling methods are proposed: least squares method, back propagation (BP artificial neural network, and BP artificial neural network based on genetic algorithms. Comparing the accuracy and convergence rate of three kinds of hysteresis modelling methods, the results show that the convergence rate of least squares method is the fastest, and the convergence accuracy of BP artificial neural networks based on genetic algorithms is the highest.

  9. Bio-inspired Actuating System for Swimming Using Shape Memory Alloy Composites

    Institute of Scientific and Technical Information of China (English)

    Tao Tao; Yuan-Chang Liang; Minoru Taya

    2006-01-01

    The paper addresses the designs of a caudal peduncle actuator, which is able to furnish a thrust for swimming of a robotic fish. The caudal peduncle actuator is based on concepts of ferromagnetic shape memory alloy (FSMA) composite and hybrid mechanism that can provide a fast response and a strong thrust. The caudal peduncle actuator was inspired by Scomber Scombrus which utilises thunniform mode swimming, which is the most efficient locomotion mode evolved in the aquatic environment, where the thrust is generated by the lift-based method, allowing high cruising speeds to be maintained for a long period of time. The morphology of an average size Scomber Scombrus (length in 310 mm) was investigated, and a 1:1 scale caudal peduncle actuator prototype was modelled and fabricated. The propulsive wave characteristics of the fish at steady speeds were employed as initial design objectives. Some key design parameters are investigated, i.e. aspect ratio (AR) (AR = 3.49), Reynolds number (Re = 429 649), reduced frequency (σ = 1.03), Strouhal number (St = 0.306) and the maximum strain of the bent tail was estimated at ε = 1.11% which is in the range of superelasticity. The experimental test of the actuator was carried out in a water tank. By applying 7 V and 2.5 A, the actuator can reach the tip-to-tip rotational angle of 85° at 4 Hz.

  10. Production of NiTi shape memory alloys via electro-deoxidation utilizing an inert anode

    Energy Technology Data Exchange (ETDEWEB)

    Jiao Shuqiang, E-mail: sjiao@ustb.edu.c [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China)] [Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom); Zhang Linlin; Zhu Hongmin [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Fray, Derek J., E-mail: djf25@cam.ac.u [Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom)

    2010-09-30

    NiTi shape memory alloys (SMA) with equiatomic composition of Ni and Ti were prepared by electro-deoxidation, in molten calcium chloride, at 950 {sup o}C. Constant voltage electro-deoxidation was conducted using a NiTiO{sub 3} cathode, and either a carbon anode or a novel CaRuO{sub 3}/CaTiO{sub 3} composite inert anode. Both anode materials successfully allowed NiTi shape memory alloy to be obtained. The primary difference is that molecular oxygen was produced on the inert anode, instead of environmentally undesired CO{sub 2} greenhouse gases on the carbon anode. Indeed, it was found that carbon could successfully be substituted with conductive calcium titanate-calcium ruthenate composites for electro-deoxidation. Furthermore, DSC was used to analyze the phase transformation of NiTi shape memory alloys, with results revealing the existence of reversible martensite-austenite phase transformations during the cooling and heating process.

  11. Artificial trachea reconstruction with two-stage approach using memory-alloy mesh

    Institute of Scientific and Technical Information of China (English)

    赵凤瑞; 张银合; 刘世民; 余建军

    2003-01-01

    @@ Artificial tracheal prosthesis is now a challenge to the entire surgical field all over the world. Previously, all kinds of prosthesis were "inner stent" that could not be integrated with native trachea. Since there is an interface between smooth surface of the prosthesis and living tissues, and the inner side of the prosthesis is not covered with living membrane, infections always happen around the prosthesis. We then developed a new technique, which combined memory-alloy mesh with traditional operative procedures. Memory-alloy mesh is extensible, flexible and can maintain the shape of a tube. It has very good compatibility with tissues and no antigenicity. Thus, it is the most desirable material nowadays that can be found to make the frame of an artificial trachea by using a two-stage approach. That is imbedding a pre-shaped memory-alloy mesh under skin or endothelium (pleura or peritoneum), and then making the "sandwich" pedicle skin and muscle flap to a pedicled artificial trachea anastomosed with native trachea. After a two-year experimental study, a patient received the artificial trachea replacement on April 18, 2002, with a good result.

  12. Miniaturized Rotary Actuators Using Shape Memory Alloy for Insect-Type MEMS Microrobot

    Directory of Open Access Journals (Sweden)

    Ken Saito

    2016-03-01

    Full Text Available Although several types of locomotive microrobots have been developed, most of them have difficulty locomoting on uneven surfaces. Thus, we have been focused on microrobots that can locomote using step patterns. We are studying insect-type microrobot systems. The locomotion of the microrobot is generated by rotational movements of the shape memory alloy-type rotary actuator. In addition, we have constructed artificial neural networks by using analog integrated circuit (IC technology. The artificial neural networks can output the driving waveform without using software programs. The shape memory alloy-type rotary actuator and the artificial neural networks are constructed with silicon wafers; they can be integrated by using micro-electromechanical system (MEMS technology. As a result, the MEMS microrobot system can locomote using step patterns. The insect-type MEMS microrobot system is 0.079 g in weight and less than 5.0 mm in size, and its locomotion speed is 2 mm/min. The locomotion speed is slow because the heat of the shape memory alloy conducts to the mechanical parts of the MEMS microrobot. In this paper, we discuss a new rotary actuator compared with the previous model and show the continuous rotation of the proposed rotary actuator.

  13. Titanium-nickel shape memory alloy foams for bone tissue engineering.

    Science.gov (United States)

    Xiong, J Y; Li, Y C; Wang, X J; Hodgson, P D; Wen, C E

    2008-07-01

    Titanium-nickel (TiNi) shape memory alloy (SMA) foams with an open-cell porous structure were fabricated by space-holder sintering process and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The mechanical properties and shape memory properties of the TiNi foam samples were investigated using compressive test. Results indicate that the plateau stresses and elastic moduli of the foams under compression decrease with the increase of their porosities. The plateau stresses and elastic moduli are measured to be from 1.9 to 38.3 MPa and from 30 to 860 MPa for the TiNi foam samples with porosities ranged from 71% to 87%, respectively. The mechanical properties of the TiNi alloy foams can be tailored to match those of bone. The TiNi alloy foams exhibit shape memory effect (SME), and it is found that the recoverable strain due to SME decreases with the increase of foam porosity.

  14. In Situ Neutron Diffraction Study of NiTi-21Pt High-Temperature Shape Memory Alloys

    Science.gov (United States)

    Benafan, O.; Gaydosh, D. J.; Noebe, R. D.; Qiu, S.; Vaidyanathan, R.

    2016-12-01

    In situ neutron diffraction was used to investigate the microstructural features of stoichiometric and Ti-rich NiTiPt high-temperature shape memory alloys with target compositions of Ni29Ti50Pt21 and Ni28.5Ti50.5Pt21 (in atomic percent), respectively. The alloys' isothermal and thermomechanical properties (i.e., moduli, thermal expansion, transformation strains, and dimensional stability) were correlated to the lattice strains, volume-averaged elastic moduli, and textures as determined by neutron diffraction. In addition, the unique aspects of this technique when applied to martensitic transformations in shape memory alloys are highlighted throughout the paper.

  15. Structure and properties of nitrided surface layer produced on NiTi shape memory alloy by low temperature plasma nitriding

    Energy Technology Data Exchange (ETDEWEB)

    Czarnowska, Elżbieta [Children' s Memorial Health Institute, Pathology Department, Al. Dzieci Polskich 20, 04-730 Warsaw (Poland); Borowski, Tomasz [Warsaw University of Technology, Faculty of Materials Science and Engineering, Wołoska 141, 02-507 Warsaw (Poland); Sowińska, Agnieszka [Children' s Memorial Health Institute, Pathology Department, Al. Dzieci Polskich 20, 04-730 Warsaw (Poland); Lelątko, Józef [Silesia University, Faculty of Computer Science and Materials Science, 75 Pułku Piechoty 1A, 41-500 Chorzów (Poland); Oleksiak, Justyna; Kamiński, Janusz; Tarnowski, Michał [Warsaw University of Technology, Faculty of Materials Science and Engineering, Wołoska 141, 02-507 Warsaw (Poland); Wierzchoń, Tadeusz, E-mail: twierz@inmat.pw.edu.pl [Warsaw University of Technology, Faculty of Materials Science and Engineering, Wołoska 141, 02-507 Warsaw (Poland)

    2015-04-15

    Highlights: • Low temperature plasma nitriding process of NiTi shape memory alloy is presented. • The possibility of treatment details of sophisticated shape. • TiN surface layer has diffusive character. • TiN surface layer increases corrosion resistance of NiTi alloy. • Produced TiN layer modify the biological properties of NiTi alloy. - Abstract: NiTi shape memory alloys are used for bone and cardiological implants. However, on account of the metallosis effect, i.e. the release of the alloy elements into surrounding tissues, they are subjected to various surface treatment processes in order to improve their corrosion resistance and biocompatibility without influencing the required shape memory properties. In this paper, the microstructure, topography and morphology of TiN surface layer on NiTi alloy, and corrosion resistance, both before and after nitriding in low-temperature plasma at 290 °C, are presented. Examinations with the use of the potentiodynamic and electrochemical impedance spectroscopy methods were carried out and show an increase of corrosion resistance in Ringer's solution after glow-discharge nitriding. This surface titanium nitride layer also improved the adhesion of platelets and the proliferation of osteoblasts, which was investigated in in vitro experiments with human cells. Experimental data revealed that nitriding NiTi shape memory alloy under low-temperature plasma improves its properties for bone implant applications.

  16. A three-dimensional model of magneto-mechanical behaviors of martensite reorientation in ferromagnetic shape memory alloys

    Science.gov (United States)

    Chen, Xue; Moumni, Ziad; He, Yongjun; Zhang, Weihong

    2014-03-01

    The large strain in Ferromagnetic Shape Memory Alloys (FSMA) is due to the martensite reorientation driven by mechanical stresses and/or magnetic fields. Although most experiments studying the martensite reorientation in FSMA are under 1D condition (uniaxial stress plus a perpendicular magnetic field), it has been shown that the 2D/3D configurations can improve the working stress and give much flexibility of the material's applications [He, Y.J., Chen, X., Moumni, Z., 2011. Two-dimensional analysis to improve the output stress in ferromagnetic shape memory alloys. Journal of Applied Physics 110, 063905]. To predict the material's behaviors in 3D loading conditions, a constitutive model is developed in this paper, based on the thermodynamics of irreversible processes with internal variables. All the martensite variants are considered in the model and the temperature effect is also taken into account. The model is able to describe all the behaviors of martensite reorientation in FSMA observed in the existing experiments: rotating/non-rotating magnetic-field-induced martensite reorientation, magnetic-field-assisted super-elasticity, super-elasticity under biaxial compressions and temperature-dependence of martensite reorientation. The model is further used to study the nonlinear bending behaviors of FSMA beams and provides some basic guidelines for designing the FSMA-based bending actuators.

  17. Oscillator-based memory for serial order.

    Science.gov (United States)

    Brown, G D; Preece, T; Hulme, C

    2000-01-01

    A computational model of human memory for serial order is described (OSCillator-based Associative Recall [OSCAR]). In the model, successive list items become associated to successive states of a dynamic learning-context signal. Retrieval involves reinstatement of the learning context, successive states of which cue successive recalls. The model provides an integrated account of both item memory and order memory and allows the hierarchical representation of temporal order information. The model accounts for a wide range of serial order memory data, including differential item and order memory, transposition gradients, item similarity effects, the effects of item lag and separation in judgments of relative and absolute recency, probed serial recall data, distinctiveness effects, grouping effects at various temporal resolutions, longer term memory for serial order, list length effects, and the effects of vocabulary size on serial recall.

  18. In vitro investigation of NiTiW shape memory alloy as potential biomaterial with enhanced radiopacity.

    Science.gov (United States)

    Li, Huafang; Cong, Ying; Zheng, Yufeng; Cui, Lishan

    2016-03-01

    In the present study, a novel kind of NiTiW shape memory alloy with chemical composition of Ni43.5Ti45.5W11 (at.%) has been successfully developed with excellent X-ray radiopacity by the introduction of pure W precipitates into the NiTi matrix phase. Its microstructure, X-ray radiopacity, mechanical properties, corrosion resistance in simulated body fluid, hemocompatibility and in vitro cytocompatibility were systematically investigated. The typical microstructural feature of NiTiW alloy at room temperature was tiny pure W particles randomly distributing in the NiTi matrix phase. The presence of W precipitates was found to result in enhanced radiopacity and microhardness of NiTiW alloy in comparison to that of NiTi binary alloy. NiTiW alloy exhibits excellent shape memory effect, and a maximum shape recovery ratio of about 30% was obtained with a total prestrain of 8% for the NiTiW alloy sample. In the electrochemical test, NiTiW alloy presented an excellent corrosion resistance in simulated body fluid, comparable to that of NiTi alloy. Hemocompatibility tests indicated that the NiTiW alloy has quite low hemolysis (lower than 0.5%) and the adherent platelet showed round shape without pseudopod. Besides, in vitro cell viability tests demonstrated that the cell viability is all above 90%, and the cells spread well on the NiTiW alloy, having polygon or spindle healthy morphology. The hemocompatibility tests, in vitro cell viability tests and morphology observation indicated that the NiTiW shape memory alloys have excellent biocompatibility. The excellent X-ray radiopacity makes the NiTiW alloys show obvious advantages in orthopedic, stomatological, neurological and cardiovascular domains where radiopacity is quite important factor in order to guarantee successful implantation. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Ferromagnetic interactions and martensitic transformation in Fe doped Ni-Mn-In shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Lobo, D. N.; Priolkar, K. R., E-mail: krp@unigoa.ac.in [Department of Physics, Goa University, Taleigao Plateau, Goa 403 206 (India); Emura, S. [Institute of Scientific and Industrial Research, Osaka University, 8-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Nigam, A. K. [Tata Institute of Fundamental Research, Dr. Homi Bhabha Road, Colaba, Mumbai 400 005 (India)

    2014-11-14

    The structure, magnetic, and martensitic properties of Fe doped Ni-Mn-In magnetic shape memory alloys have been studied by differential scanning calorimetry, magnetization, resistivity, X-ray diffraction (XRD), and EXAFS. While Ni{sub 2}MnIn{sub 1−x}Fe{sub x} (0 ≤ x ≤ 0.6) alloys are ferromagnetic and non martensitic, the martensitic transformation temperature in Ni{sub 2}Mn{sub 1.5}In{sub 1−y}Fe{sub y} and Ni{sub 2}Mn{sub 1.6}In{sub 1−y}Fe{sub y} increases for lower Fe concentrations (y ≤ 0.05) before decreasing sharply for higher Fe concentrations. XRD analysis reveals presence of cubic and tetragonal structural phases in Ni{sub 2}MnIn{sub 1−x}Fe{sub x} at room temperature with tetragonal phase content increasing with Fe doping. Even though the local structure around Mn and Ni in these Fe doped alloys is similar to martensitic Mn rich Ni-Mn-In alloys, presence of ferromagnetic interactions and structural disorder induced by Fe affect Mn-Ni-Mn antiferromagnetic interactions resulting in suppression of martensitic transformation in these Fe doped alloys.

  20. Vanadium-base alloys for fusion reactor applications

    Energy Technology Data Exchange (ETDEWEB)

    Smith, D.L.; Loomis, B.A.; Diercks, D.R.

    1984-10-01

    Vanadium-base alloys offer potentially significant advantages over other candidate alloys as a structural material for fusion reactor first wall/blanket applications. Although the data base is more limited than that for the other leading candidate structural materials, viz., austenitic and ferritic steels, vanadium-base alloys exhibit several properties that make them particularly attractive for the fusion reactor environment. This paper presents a review of the structural material requirements, a summary of the materials data base for selected vanadium-base alloys, and a comparison of projected performance characteristics compared to other candidate alloys. Also, critical research and development (R and D) needs are defined.