WorldWideScience

Sample records for measured winter performance

  1. Winter maintenance performance measure.

    Science.gov (United States)

    2016-01-01

    The Winter Performance Index is a method of quantifying winter storm events and the DOTs response to them. : It is a valuable tool for evaluating the States maintenance practices, performing post-storm analysis, training : maintenance personnel...

  2. Comparison of Performance Measurements of Photovoltaic Modules during Winter Months in Taxila, Pakistan

    Directory of Open Access Journals (Sweden)

    Muhammad Anser Bashir

    2014-01-01

    Full Text Available This paper presents the comparative performance evaluation of three commercially available photovoltaic modules (monocrystalline, polycrystalline, and single junction amorphous silicon in Taxila, Pakistan. The experimentation was carried out at outdoor conditions for winter months. Power output, module efficiency, and performance ratio were calculated for each module and the effect of module temperature and solar irradiance on these parameters was investigated. Module parameters showed strong dependence on the solar irradiance and module temperature. Monocrystalline and polycrystalline modules showed better performance in high irradiance condition whereas it decreased suddenly with decrease in irradiance. Amorphous solar module also showed good performance in low irradiance due to its better light absorbing characteristics and thus showed higher average performance ratio. Monocrystalline photovoltaic module showed higher monthly average module efficiency and was found to be more efficient at this site. Module efficiency and performance ratio showed a decreasing trend with increase of irradiance and photovoltaic module back surface temperature.

  3. Measuring Transpiration to Regulate Winter Irrigation Rates

    Energy Technology Data Exchange (ETDEWEB)

    Samuelson, Lisa [Auburn University

    2006-11-08

    Periodic transpiration (monthly sums) in a young loblolly pine plantation between ages 3 and 6 was measured using thermal dissipation probes. Fertilization and fertilization with irrigation were better than irrigation alone in increasing transpiration of young loblolly pines during winter months, apparently because of increased leaf area in fertilized trees. Irrigation alone did not significantly increase transpiration compared with the non-fertilized and non-irrigated control plots.

  4. Experimental winter warming modifies thermal performance and primes acorn ants for warm weather

    DEFF Research Database (Denmark)

    MacLean, Heidi J.; Penick, Clint A.; Dunn, Robert R.

    2017-01-01

    The frequency of warm winter days is increasing under global climate change, but how organisms respond to warmer winters is not well understood. Most studies focus on growing season responses to warming. Locomotor performance is often highly sensitive to temperature, and can determine fitness...... outcomes through a variety of mechanisms including resource acquisition and predator escape. As a consequence, locomotor performance, and its impacts on fitness, may be strongly affected by winter warming in winter-active species. Here we use the acorn ant, Temnothorax curvispinosus, to explore how thermal...... performance (temperature-driven plasticity) in running speed is influenced by experimental winter warming of 3–5 °C above ambient in a field setting. We used running speed as a measure of performance as it is a common locomotor trait that influences acquisition of nest sites and food in acorn ants...

  5. Slip resistance of winter footwear on snow and ice measured using maximum achievable incline.

    Science.gov (United States)

    Hsu, Jennifer; Shaw, Robert; Novak, Alison; Li, Yue; Ormerod, Marcus; Newton, Rita; Dutta, Tilak; Fernie, Geoff

    2016-05-01

    Protective footwear is necessary for preventing injurious slips and falls in winter conditions. Valid methods for assessing footwear slip resistance on winter surfaces are needed in order to evaluate footwear and outsole designs. The purpose of this study was to utilise a method of testing winter footwear that was ecologically valid in terms of involving actual human testers walking on realistic winter surfaces to produce objective measures of slip resistance. During the experiment, eight participants tested six styles of footwear on wet ice, on dry ice, and on dry ice after walking over soft snow. Slip resistance was measured by determining the maximum incline angles participants were able to walk up and down in each footwear-surface combination. The results indicated that testing on a variety of surfaces is necessary for establishing winter footwear performance and that standard mechanical bench tests for footwear slip resistance do not adequately reflect actual performance. Practitioner Summary: Existing standardised methods for measuring footwear slip resistance lack validation on winter surfaces. By determining the maximum inclines participants could walk up and down slopes of wet ice, dry ice, and ice with snow, in a range of footwear, an ecologically valid test for measuring winter footwear performance was established.

  6. Performance of blueberry cultivars under mild winter conditions

    Directory of Open Access Journals (Sweden)

    José Gilberto Sousa Medeiros

    2017-08-01

    Full Text Available ABSTRACT: Evaluation of yield performance is important to find the most adapted blueberry cultivars in a particular region. This research aimed to evaluate the flowering and hasvesting periods, the production per plant, and fruit quality of eight rabbiteye blueberry cultivars (Aliceblue, Bluebelle, Bluegem, Briteblue, Climax, Delite, Powderblue, and Woodard and two highbush blueberries (Georgiagem and O’Neal, in mild winter conditions in Pinhais-PR. Flowering and harvesting periods, production, berry weight, size, pH, soluble solids, titratable acidity, ratio and color of the fruits were evaluated in the 2013/2014 and 2014/2015 growing seasons, when the plants had two and three years old, respectively. Cultivars flowered from August to September, and harvest was concentrated in November and December. Berry weight, size, pH, soluble solids and acidity varied among the cultivars. The average ratios of 14.97 and 13.39 for each crop proved that the cultivars have good fruit quality. There was little variation in fruit color in the two years evaluated. Blueberry cultivars showed the staining characteristics and physical and chemical attributes of quality compatible to blueberry from other traditional regions. Under mild winter conditions, young plants of rabbiteye blueberry cultivars, Climax, Delite, Bluegem and Powderblue, are the most productive, while the highbusch cultivars bear few fruits.

  7. Winter precipitation particle size distribution measurement by Multi-Angle Snowflake Camera

    Science.gov (United States)

    Huang, Gwo-Jong; Kleinkort, Cameron; Bringi, V. N.; Notaroš, Branislav M.

    2017-12-01

    From the radar meteorology viewpoint, the most important properties for quantitative precipitation estimation of winter events are 3D shape, size, and mass of precipitation particles, as well as the particle size distribution (PSD). In order to measure these properties precisely, optical instruments may be the best choice. The Multi-Angle Snowflake Camera (MASC) is a relatively new instrument equipped with three high-resolution cameras to capture the winter precipitation particle images from three non-parallel angles, in addition to measuring the particle fall speed using two pairs of infrared motion sensors. However, the results from the MASC so far are usually presented as monthly or seasonally, and particle sizes are given as histograms, no previous studies have used the MASC for a single storm study, and no researchers use MASC to measure the PSD. We propose the methodology for obtaining the winter precipitation PSD measured by the MASC, and present and discuss the development, implementation, and application of the new technique for PSD computation based on MASC images. Overall, this is the first study of the MASC-based PSD. We present PSD MASC experiments and results for segments of two snow events to demonstrate the performance of our PSD algorithm. The results show that the self-consistency of the MASC measured single-camera PSDs is good. To cross-validate PSD measurements, we compare MASC mean PSD (averaged over three cameras) with the collocated 2D Video Disdrometer, and observe good agreements of the two sets of results.

  8. Performance of Chlorella sorokiniana under simulated extreme winter conditions

    NARCIS (Netherlands)

    Cuaresma, M.; Buffing, M.F.; Janssen, M.G.J.; Lobato, C.V.; Wijffels, R.H.

    2012-01-01

    High annual microalgae productivities can only be achieved if solar light is efficiently used through the different seasons. During winter the productivity is low because of the light and temperature conditions. The productivity and photosynthetic efficiency of Chlorella sorokiniana were assessed

  9. Developing Effective Performance Measures

    Science.gov (United States)

    2014-10-14

    University When Performance Measurement Goes Bad Laziness Vanity Narcissism Too Many Pettiness Inanity 52 Developing Effective...Kasunic, October 14, 2014 © 2014 Carnegie Mellon University Narcissism Measuring performance from the organization’s point of view, rather than from

  10. Performance evaluation of commercial maize hybrids across diverse Terai environments during the winter season in Nepal

    Directory of Open Access Journals (Sweden)

    Mahendra Prasad Tripathi

    2016-12-01

    Full Text Available The hybrid maize cultivars of multinational seed companies are gradually being popular among the farmers in Nepal. This paper reports on research finding of 117 maize hybrids of 20 seed companies assessed for grain yield and other traits at three sites in winter season of 2011 and 2012. The objective of the study was to identify superior maize hybrids suitable for winter time planting in eastern, central and inner Terai of Nepal. Across site analysis of variance revealed that highly significant effect of genotype and genotype × environment interaction (GEI on grain yield of commercial hybrids. Overall, 47 genotypes of 16 seed companies identified as high yielding and stable based on superiority measures. The statistical analysis ranked topmost three genotypes among tested hybrids as P3856 (10515 kg ha-1, Bisco prince (8763 kg ha-1 as well as Shaktiman (8654 kg ha-1 in the first year; and 3022 (8378 kg ha-1, Kirtiman manik (8323 kg ha-1 as well as Top class (7996 kg ha-1 in the second year. It can be concluded that stable and good performing hybrids identified as potential commercial hybrids for general cultivation on similar environments in Nepal.

  11. Assessing the performance of winter footwear using a new maximum achievable incline method.

    Science.gov (United States)

    Hsu, Jennifer; Li, Yue; Dutta, Tilak; Fernie, Geoff

    2015-09-01

    More informative tests of winter footwear performance are required in order to identify footwear that will prevent injurious slips and falls on icy conditions. In this study, eight participants tested four styles of winter boots on smooth wet ice. The surface was progressively tilted to create increasing longitudinal and cross-slopes until participants could no longer continue standing or walking. Maximum achievable incline angles provided consistent measures of footwear slip resistance and demonstrated better resolution than mechanical tests. One footwear outsole material and tread combination outperformed the others on wet ice allowing participants to successfully walk on steep longitudinal slopes of 17.5° ± 1.9° (mean ± SD). By further exploiting the methodology to include additional surfaces and contaminants, such tests could be used to optimize tread designs and materials that are ideal for reducing the risk of slips and falls. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  12. Performance Measurement und Environmental Performance Measurement

    OpenAIRE

    Sturm, Anke

    2000-01-01

    Die Zielsetzung der vorliegenden Dissertationsschrift besteht in der Entwicklung einer systematisierten Vorgehensweise, eines Controllingmodells, zur unternehmensinternen Umweltleistungsmessung. Das entwickelte Environmental Performance Measurement (EPM)-Modell umfaßt die fünf Stufen Festlegung der Ziele der Umweltleistungsmessung (1. Stufe), Erfassung der Umwelteinflüsse nach der ökologischen Erfolgsspaltung (2. Stufe), Bewertung der Umwelteinflüsse auf der Grundlage des qualitätszielbezogen...

  13. Effects of winter military training on energy balance, whole-body protein balance, muscle damage, soreness, and physical performance.

    Science.gov (United States)

    Margolis, Lee M; Murphy, Nancy E; Martini, Svein; Spitz, Marissa G; Thrane, Ingjerd; McGraw, Susan M; Blatny, Janet-Martha; Castellani, John W; Rood, Jennifer C; Young, Andrew J; Montain, Scott J; Gundersen, Yngvar; Pasiakos, Stefan M

    2014-12-01

    Physiological consequences of winter military operations are not well described. This study examined Norwegian soldiers (n = 21 males) participating in a physically demanding winter training program to evaluate whether short-term military training alters energy and whole-body protein balance, muscle damage, soreness, and performance. Energy expenditure (D2(18)O) and intake were measured daily, and postabsorptive whole-body protein turnover ([(15)N]-glycine), muscle damage, soreness, and performance (vertical jump) were assessed at baseline, following a 4-day, military task training phase (MTT) and after a 3-day, 54-km ski march (SKI). Energy intake (kcal·day(-1)) increased (P balance was lower (P military training provide the basis for future studies to evaluate nutritional strategies that attenuate protein loss and sustain performance during severe energy deficits.

  14. Aircraft measurements to characterize polluted winter boundary layers: Overview of twin otter flights during the Utah Winter Fine Particulate Matter Study

    Science.gov (United States)

    Brown, S. S.; Baasandorj, M.; Franchin, A.; Middlebrook, A. M.; Goldberger, L.; Thornton, J. A.; Dube, W. P.; McDuffie, E. E.; Womack, C.; Fibiger, D. L.; Moravek, A.; Clark, J. C.; Murphy, J. G.; Mitchell, R.

    2017-12-01

    Winter air pollution is a significant public health concern. In many regions of the U.S., Europe and Asia, wintertime particulate matter concentrations exceed national and / or international air quality standards. Winter air pollution also represents a scientific challenge because these events occur during stagnation events in shallow, vertically stratified boundary layers whose composition is difficult to probe from surface level measurements. Chemical processes responsible for the conversion of primary emissions to secondary pollutants such as ammonium nitrate aerosol vary with height above ground level. Sources of oxidants are poorly understood and may result from both local chemical production and mixing between shallow inversion layers and background air. During the Utah Winter Fine Particulate Study (UWFPS) in January - February 2017, the NOAA twin otter executed 23 research flights with a payload designed to characterize the formation of ammonium nitrate aerosol in three mountain valleys of northern Utah (Salt Lake, Cache, and Utah). These valleys are subject to periodic episodes of winter aerosol pollution well in excess of U.S. national ambient air quality standards. This presentation will describe the measurement strategy of the twin otter flights to address the specific features of aerosol pollution within winter boundary layer of this region. This strategy is relevant to understanding the broader issue of winter air pollution in other regions and potentially to the design of future studies. The presentation will summarize findings from UWFPS related to boundary layer structure, emissions and chemical processes responsible for ammonium nitrate aerosol in this region.

  15. Performance Measurement at Universities

    DEFF Research Database (Denmark)

    Lueg, Klarissa

    2014-01-01

    This paper proposes empirical approaches to testing the reliability, validity, and organizational effectiveness of student evaluations of teaching (SET) as a performance measurement instrument in knowledge management at the institutional level of universities. Departing from Weber’s concept...

  16. Comparison of summer and winter objectively measured physical activity and sedentary behavior in older adults

    DEFF Research Database (Denmark)

    Arnardottir, Nanna Yr; Oskarsdottir, Nina Dora; Brychta, Robert J.

    2017-01-01

    In Iceland, there is a large variation in daylight between summer and winter. The aim of the study was to identify how this large variation influences physical activity (PA) and sedentary behavior (SB). Free living PA was measured by a waist-worn accelerometer for one week during waking hours...... categories, except for the moderate-to-vigorous PA (MVPA), and SB was reduced. More lifestyle PA (LSPA) was accumulated in ≥5-min bouts during summer than winter, especially among highly active participants. This information could be important for policy makers and health professionals working with older...

  17. The performance measurement manifesto.

    Science.gov (United States)

    Eccles, R G

    1991-01-01

    The leading indicators of business performance cannot be found in financial data alone. Quality, customer satisfaction, innovation, market share--metrics like these often reflect a company's economic condition and growth prospects better than its reported earnings do. Depending on an accounting department to reveal a company's future will leave it hopelessly mired in the past. More and more managers are changing their company's performance measurement systems to track nonfinancial measures and reinforce new competitive strategies. Five activities are essential: developing an information architecture; putting the technology in place to support this architecture; aligning bonuses and other incentives with the new system; drawing on outside resources; and designing an internal process to ensure the other four activities occur. New technologies and more sophisticated databases have made the change to nonfinancial performance measurement systems possible and economically feasible. Industry and trade associations, consulting firms, and public accounting firms that already have well-developed methods for assessing market share and other performance metrics can add to the revolution's momentum--as well as profit from the business opportunities it presents. Every company will have its own key measures and distinctive process for implementing the change. But making it happen will always require careful preparation, perseverance, and the conviction of the CEO that it must be carried through. When one leading company can demonstrate the long-term advantage of its superior performance on quality or innovation or any other nonfinancial measure, it will change the rules for all its rivals forever.

  18. Enterprise performance measurement systems

    Directory of Open Access Journals (Sweden)

    Milija Bogavac

    2014-10-01

    Full Text Available Performance measurement systems are an extremely important part of the control and management actions, because in this way a company can determine its business potential, its market power, potential and current level of business efficiency. The significance of measurement consists in influencing the relationship between the results of reproduction (total volume of production, value of production, total revenue and profit and investments to achieve these results (factors of production spending and hiring capital in order to achieve the highest possible quality of the economy. (The relationship between the results of reproduction and investment to achieve them quantitatively determines economic success as the quality of the economy. Measuring performance allows the identification of the economic resources the company has, so looking at the key factors that affect its performance can help to determine the appropriate course of action.

  19. Productivity and Performance Measurement

    DEFF Research Database (Denmark)

    Hald, Kim Sundtoft; Spring, Martin

    This study explores conceptually how performance measurement as discussed in the literature, enables or constrains the ability to manage and improve productivity. It uses an inter-disciplinary literature review to identify five areas of concern relating productivity accounting to the ability...... to improve productivity: “Productivity representation”; “productivity incentives”, “productivity intervention”; “productivity trade-off or synergy” and “productivity strategy and context”. The paper discusses these areas of concern and expands our knowledge of how productivity and performance measurement...

  20. Measuring Firm Performance

    DEFF Research Database (Denmark)

    Assaf, A. George; Josiassen, Alexander; Gillen, David

    2014-01-01

    Set in the airport industry, this paper measures firm performance using both desirable and bad outputs (i.e. airport delays). We first estimate a model that does not include the bad outputs and then a model that includes bad outputs. The results show important differences in the efficiency...

  1. Benchmarking and Performance Measurement.

    Science.gov (United States)

    Town, J. Stephen

    This paper defines benchmarking and its relationship to quality management, describes a project which applied the technique in a library context, and explores the relationship between performance measurement and benchmarking. Numerous benchmarking methods contain similar elements: deciding what to benchmark; identifying partners; gathering…

  2. Physical and chemical characterization of urban winter-time aerosols by mobile measurements in Helsinki, Finland

    Science.gov (United States)

    Pirjola, Liisa; Niemi, Jarkko V.; Saarikoski, Sanna; Aurela, Minna; Enroth, Joonas; Carbone, Samara; Saarnio, Karri; Kuuluvainen, Heino; Kousa, Anu; Rönkkö, Topi; Hillamo, Risto

    2017-06-01

    A two-week measurement campaign by a mobile laboratory van was performed in urban environments in the Helsinki metropolitan area, Finland, in winter 2012, to obtain a comprehensive view on aerosol properties and sources. The abundances and physico-chemical properties of particles varied strongly in time and space, depending on the main sources of aerosols. Four major types of winter aerosol were recognized: 1) clean background aerosol with low particle number (Ntot) and lung deposited surface area (LDSA) concentrations due to marine air flows from the Atlantic Ocean; 2) long-range transported (LRT) pollution aerosol due to air flows from eastern Europe where the particles were characterized by the high contribution of oxygenated organic aerosol (OOA) and inorganic species, particularly sulphate, but low BC contribution, and their size distribution possessed an additional accumulation mode; 3) fresh smoke plumes from residential wood combustion in suburban small houses, these particles were characterized by high biomass burning organic aerosol (BBOA) and black carbon (BC) concentrations; and 4) fresh emissions from traffic while driving on busy streets in the city centre and on the highways during morning rush hours. This aerosol was characterized by high concentration of Ntot, LDSA, small particles in the nucleation mode, as well as high hydrocarbon-like organic aerosol (HOA) and BC concentrations. In general, secondary components (OOA, NO3, NH4, and SO4) dominated the PM1 chemical composition during the LRT episode accounting for 70-80% of the PM1 mass, whereas fresh primary emissions (BC, HOA and BBOA) dominated the local traffic and wood burning emissions. The major individual particle types observed with electron microscopy analysis (TEM/EDX) were mainly related to residential wood combustion (K/S/C-rich, soot, other C-rich particles), traffic (soot, Si/Al-rich, Fe-rich), heavy fuel oil combustion in heat plants or ships (S with V-Ni-Fe), LRT pollutants (S

  3. Winter Performance of Inter-Locking Pavers—Stormwater Quantity and Quality

    Directory of Open Access Journals (Sweden)

    Angus Chu

    2012-12-01

    Full Text Available This study examined the effectiveness of open-joint inter-locking pavers in a permeable pavement in cold (winter conditions. A field-scale inter-locking paver cell (UNI Eco-Optiloc® was built to evaluate the hydraulic performance and water quality improvements experienced during freeze-thaw and frozen conditions in Calgary, Alberta, Canada. Hydraulic performance was assessed using stormwater runoff reduction (peaks and volumes and surface infiltration capacity. Water quality performance for removal of total suspended solids (TSS, total nitrogen (TN, total phosphorous (TP and three heavy metals: copper, lead and zinc, was assessed. Results from the study demonstrated that the inter-locking pavers were effective in attenuating stormwater runoff peak volumes. The surface infiltration capacity decreased significantly due to the deposition of sanding and de-icing materials on the pavement surface during winter operation. Infiltrated stormwater was stored and treated within the pavement structure, which showed removal rates of 91% for TSS, 78% for TP, 6% for TN, 68% for zinc, 69% for copper and 55% for lead.

  4. Using Technical Performance Measures

    Science.gov (United States)

    Garrett, Christopher J.; Levack, Daniel J. H.; Rhodes, Russel E.

    2011-01-01

    All programs have requirements. For these requirements to be met, there must be a means of measurement. A Technical Performance Measure (TPM) is defined to produce a measured quantity that can be compared to the requirement. In practice, the TPM is often expressed as a maximum or minimum and a goal. Example TPMs for a rocket program are: vacuum or sea level specific impulse (lsp), weight, reliability (often expressed as a failure rate), schedule, operability (turn-around time), design and development cost, production cost, and operating cost. Program status is evaluated by comparing the TPMs against specified values of the requirements. During the program many design decisions are made and most of them affect some or all of the TPMs. Often, the same design decision changes some TPMs favorably while affecting other TPMs unfavorably. The problem then becomes how to compare the effects of a design decision on different TPMs. How much failure rate is one second of specific impulse worth? How many days of schedule is one pound of weight worth? In other words, how to compare dissimilar quantities in order to trade and manage the TPMs to meet all requirements. One method that has been used successfully and has a mathematical basis is Utility Analysis. Utility Analysis enables quantitative comparison among dissimilar attributes. It uses a mathematical model that maps decision maker preferences over the tradeable range of each attribute. It is capable of modeling both independent and dependent attributes. Utility Analysis is well supported in the literature on Decision Theory. It has been used at Pratt & Whitney Rocketdyne for internal programs and for contracted work such as the J-2X rocket engine program. This paper describes the construction of TPMs and describes Utility Analysis. It then discusses the use of TPMs in design trades and to manage margin during a program using Utility Analysis.

  5. Strategic Measures of Teacher Performance

    Science.gov (United States)

    Milanowski, Anthony

    2011-01-01

    Managing the human capital in education requires measuring teacher performance. To measure performance, administrators need to combine measures of practice with measures of outcomes, such as value-added measures, and three measurement systems are needed: classroom observations, performance assessments or work samples, and classroom walkthroughs.…

  6. Performance study of desiccant coated heat exchanger air conditioning system in winter

    International Nuclear Information System (INIS)

    Ge, T.S.; Dai, Y.J.; Wang, R.Z.

    2016-01-01

    Highlights: • Performance of desiccant coated heat exchanger AC system is predicted. • Effects of main operation parameters and climatic conditions are discussed. • Regeneration temperature of 30 °C is recommended under simulation condition. • Higher ambient humidity ratio results in increased humidity ratio of supply air. • Temperature of ambient air has neglectable effect on supply air. - Abstract: Conventional air source heat pump system faces several challenges when adopted in winter season. Solid desiccant air conditioning system can provide humidification and heating power simultaneously and can be driven by low grade thermal energy; it provides a good alternative for air source heat pump systems. However, conventional solid desiccant air conditioning system adopts desiccant wheel with high cost as core component, which hinders the development of such system. Recently, desiccant coated heat exchanger (DCHE) with low initial cost and high efficiency was developed and this paper aims to investigate performance of DCHE air conditioning system adopted in Shanghai winter season. Performance of the system is predicted by a developed mathematical model where supply air states, mass of humidification and coefficient of performance (COP) are adopted as performance indices to evaluate the feasibility and energy utilization ratio of the system. Effects of regeneration water temperature on system performance are analyzed. It is found that under the simulation condition, relatively low regeneration temperature (such as 20 °C) cannot meet the designed standard and relatively high regeneration temperature (such as 40 °C) provides too much extra heating power, thus moderate regeneration temperature around 30 °C is recommended. Meanwhile, switch time is a crucial operation parameter for the system to obtain satisfied supply air, switch time from 40 s to 80 s and from 70 s to 240 s are recommended for transient and average supply air states, respectively. Both

  7. Freight performance measures : approach analysis.

    Science.gov (United States)

    2010-05-01

    This report reviews the existing state of the art and also the state of the practice of freight performance measurement. Most performance measures at the state level have aimed at evaluating highway or transit infrastructure performance with an empha...

  8. Measured Performance of a Low Temperature Air Source Heat Pump

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, R. K. [Johnson Research LLC, Pueblo West, CO (United States)

    2013-09-01

    A 4-ton Low Temperature Heat Pump (LTHP) manufactured by Hallowell International was installed in a residence near New Haven, Connecticut and monitored over two winters of operation. After attending to some significant service issues, the heat pump operated as designed. This report should be considered a review of the dual compressor 'boosted heat pump' technology. The Low Temperature Heat Pumpsystem operates with four increasing levels of capacity (heat output) as the outdoor temperature drops. The system was shown to select capacity correctly, supplying the appropriate amount of heat to the house across the full range of outdoor temperatures. The system's Coefficient of Performance (Seasonal COP, or SCOP) over two entire winters was calculated, based on measured data, to be 3.29over the first winter and 2.68 over the second winter. A second seasonal efficiency calculation by a different method yielded a SCOP of 2.78 for the first winter and 2.83 for the second winter. This second seasonal efficiency calculation was determined by comparing measured heat pump energy use to the in situ energy use with resistance heat alone. This method is the ratio of the slopes of thedaily energy use load lines.

  9. Features static-and-dynamic performance in athletes of winter sports

    Directory of Open Access Journals (Sweden)

    Kotenko K.V.

    2014-12-01

    Full Text Available Objective: analysis of static-dynamic performance of the musculoskeletal system of athletes of winter sports. Materials and Methods. The evaluation of static-dynamic characteristics of the musculoskeletal system. Results. The highest percentage of load-balancing the body while maintaining a static position was observed in the group of athletes of speed and power of the sport and made up, the lowest — in athletes clearing difficult sport. Significant shift in the distribution of body load were detected in athletes clearing difficult sport in the speed and power sport, none of the athletes of the deviations were found. Conclusion. The survey revealed the features of the coordination ability and load balancing body in athletes of different sports: cycling, hard-house and speed-power.

  10. Forecast of winter performances of dry coolers with fin tubes; Voorspelling winterprestaties droge koelers met ribbenbuizen

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Bing [Shanghai DFYH Tech Services Co. Ltd, Shanghai (China); Wang, Xichun [Arup, Shanghai (China); Luscuere, P.G. [Faculteit Bouwkunde, Technische Universiteit Delft, Delft (Netherlands)

    2011-01-15

    A mathematical model is presented to predict the behaviors of dry coolers by considering the condensing and frosting. It employs one-dimensional transient finite differential formulation with variation of the frost density and thickness. The model is validated by experiments and predicts the heat transfer performance with an accuracy within 2.19%. It is helpful for the operation of dry coolers in winter. [Dutch] In dit artikel wordt een wiskundig model gepresenteerd, waarmee voortschrijdende condens- en ijsvorming op warmteoverdrachtsoppervlakken kunnen worden voorspeld aan de hand van de gevormde condens- en ijslagen. Het model maakt gebruik van eendimensionale transiente formuleringen op basis van een techniek voor lokale uitmiddeling. Hierbij wordt rekening gehouden met de varierende dichtheid en dikte van de ijslaag. Validatie van het model heeft plaatsgevonden door de resultaten te vergelijken met proefgegevens van de fabrikant van de droge koeler.

  11. Performance Measurement Baseline Change Request

    Data.gov (United States)

    Social Security Administration — The Performance Measurement Baseline Change Request template is used to document changes to scope, cost, schedule, or operational performance metrics for SSA's Major...

  12. Transit performance measures in California.

    Science.gov (United States)

    2016-04-01

    This research is the result of a California Department of Transportation (Caltrans) request to assess the most commonly : available transit performance measures in California. Caltrans wanted to understand performance measures and data used by : Metr...

  13. Measuring the Company Performance

    Directory of Open Access Journals (Sweden)

    Ion Stancu

    2006-03-01

    Full Text Available According to the logics of the efficient capital investment, the management of the investment of the saving capital in the company’s assets must conclude, on the end of the financial year, with a plus ofreal value (NPV > 0. From this point of view, in this paper we suggest the usage of an investment valuationmodel for the assessment of the company managerial and technological performance. Supposing the book value is a proxy of the just value (of assets and operational results and supposing the capital cost iscorrectly estimated, we evaluate the company’s performance both by the net present value model, and also by the company’s ability to create a surplus of the invested capital (NPV >0.Our paper also aims to identify the performance of the financial breakeven point (for which NPV is at least equal to zero as the minimum acceptable level for the company’s activity. Under this critical sales point, the company goes through the undervaluation of shareholders fortune even if the company’s sales are greater than accounting breakeven point. The performance’s activity level is one which the managers recover and surpass the cost of capital, cost which stand for the normal activity benchmark.The risks of applying of our suggested model we support go down to the confidence of accounting data and of the cost of capital estimating. In spite all of this, the usage of a sensitivity analysis to search anaverage NPV would leads to the company’s performance valuation within investment logic with a high information power.

  14. Measuring the Company Performance

    Directory of Open Access Journals (Sweden)

    Ion Stancu

    2006-01-01

    Full Text Available According to the logics of the efficient capital investment, the management of the investment of the saving capital in the company’s assets must conclude, on the end of the financial year, with a plus of real value (NPV > 0. From this point of view, in this paper we suggest the usage of an investment valuation model for the assessment of the company managerial and technological performance. Supposing the book value is a proxy of the just value (of assets and operational results and supposing the capital cost is correctly estimated, we evaluate the company’s performance both by the net present value model, and also by the company’s ability to create a surplus of the invested capital (NPV >0. Our paper also aims to identify the performance of the financial breakeven point (for which NPV is at least equal to zero as the minimum acceptable level for the company’s activity. Under this critical sales point, the company goes through the undervaluation of shareholders fortune even if the company’s sales are greater than accounting breakeven point. The performance’s activity level is one which the managers recover and surpass the cost of capital, cost which stand for the normal activity benchmark. The risks of applying of our suggested model we support go down to the confidence of accounting data and of the cost of capital estimating. In spite all of this, the usage of a sensitivity analysis to search an average NPV would leads to the company’s performance valuation within investment logic with a high information power.

  15. Economic measures of performance

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Cogeneration systems can reduce the total cost of utility service, and, in some instances where power is sold to an electric utility, can even produce a positive net revenue stream. This is, the total cogeneration revenue is greater than the cogeneration system's operating cost plus the cost of supplemental fuel and power. Whether it is sited at an existing facility or new construction, cogeneration systems do require an incremental investment over and above that which would be required if the end user were to utilize more conventional utility services. While the decision as to whether or not one should invest in cogeneration may consider such intangibles as predictability of future utility costs, reliability of electrical supply and the quality of that supply, the decision ultimately becomes one of basic economics. This chapter briefly reviews several economic measures with regard to ease of use, accuracy and financial objective

  16. Winter nightime ion temperatures and energetic electrons from 0go 6 plasma measurements

    International Nuclear Information System (INIS)

    Sanatani, S.; Breig, E.L.

    1981-01-01

    This paper presents and discusses ion temperature and suprathermal electron flux data acquired with the retarding potential analyzer on board the ogo 6 satellite when it was in solar eclipse. Attention is directed to measurements in the 400- to 800-km height interval between midnight and predawn in the northern winter nonpolar ionosphere. Statistical analysis of data recorded during a 1-month time span permits a decoupling of horizontal and altitude effects. A distinct longitudinal variation is observed for ion temperature above 500 km, with a significant relative enhancement over the western North Altantic Altitude distributions of ion temperature are compatible with Millstone Hill profiles within the common region of this enhancement. Large fluxes of energetic electrons are observed and extend to mush lower geomagnetic latitudes in the same longitude sector. Both a direct correlation in magnitude and a strong similarity in spatial extent are demonstrated for these ion temperature and electron flux data. The location of the limiting low-altitude boundary for observation of the electron fluxes is variable, dependent on local time and season as well as longitude. Variations in this boundary are found to be consistent with a calculated conjugate solar zenith angle of 99 0 +- 2 0 describing photoproduction of energetic electrons in the southern hemisphere. The ogo 6 data are considered to be indicative of an energy source originating in the sunlit summer hemisphere and providing heat via transport of photoelectrons to a broad but preferential segment of the winter nighttime mid-latitude ionosphere. Ions at other longitudes are without access to this energy source and cool to near the neutral temperature at heights to above 800 km inthe predawn hours

  17. THE MEASURABILITY OF CONTROLLING PERFORMANCE

    Directory of Open Access Journals (Sweden)

    V. Laval

    2017-04-01

    Full Text Available The urge to increase the performance of company processes is ongoing. Surveys indicate however, that many companies do not measure the controlling performance with a defined set of key performance indicators. This paper will analyze three categories of controlling key performance indicators based on their degree of measurability and their impact on the financial performance of a company. Potential measures to optimize the performance of the controlling department will be outlined and put in a logical order. The aligning of the controlling activity with the respective management expectation will be discussed as a key success factor of this improvement project.

  18. The Performance of Early-Generation Perennial Winter Cereals at 21 Sites across Four Continents

    Directory of Open Access Journals (Sweden)

    Richard C. Hayes

    2018-04-01

    Full Text Available A network of 21 experiments was established across nine countries on four continents and spanning both hemispheres, to evaluate the relative performance of early generation perennial cereal material derived from wheat, rye, and barley and to inform future breeding strategies. The experimental lines were grown in replicated single rows, and first year production and phenology characteristics as well as yield and persistence for up to three years were monitored. The study showed that the existing experimental material is all relatively short-lived (≤3 years, with environments that are milder in summer and winter generally conferring greater longevity. No pedigree was superior across this diverse network of sites although better performing lines at the higher latitude sites were generally derived from Thinopyrum intermedium. By contrast, at lower latitudes the superior lines were generally derived from Th. ponticum and Th. elongatum parentage. The study observed a poor relationship between year 1 performance and productivity in later years, highlighting the need for perennial cereal material with greater longevity to underpin future experimental evaluation, and the importance for breeding programs to emphasize post-year 1 performance in their selections. Hybrid lines derived from the tetraploid durum wheat generally showed greater longevity than derivatives of hexaploid wheat, highlighting potential for greater use of Triticum turgidum in perennial wheat breeding. We advocate a model in future breeding initiatives that develops perennial cereal genotypes for specific target environments rather than a generic product for one global market. These products may include a diversity of cultivars derived from locally adapted annual and perennial parents. In this scenario the breeding program may have access to only a limited range of adapted perennial grass parents. In other situations, such as at very high latitude environments, perennial crops derived

  19. Rocket measurements of positive ions during polar mesosphere winter echo conditions

    Directory of Open Access Journals (Sweden)

    A. Brattli

    2006-01-01

    Full Text Available On 18 January 2005, two small, instrumented rockets were launched from Andøya Rocket Range (69.3° N, 16° E during conditions with Polar Mesosphere Winter Echoes (PMWE. Each of the rockets was equipped with a Positive Ion Probe (PIP and a Faraday rotation/differential absorption experiment, and was launched as part of a salvo of meteorological rockets measuring temperature and wind using falling spheres and chaff. Layers of PMWE were detected between 55 and 77 km by the 53.5 MHz ALWIN radar. The rockets were launched during a solar proton event, and measured extremely high ion densities, of order 1010 m−3, in the region where PMWE were observed. The density measurements were analyzed with the wavelet transform technique. At large length scales, ~103 m, the power spectral density can be fitted with a k−3 wave number dependence, consistent with saturated gravity waves. Outside the PMWE layers the k−3 spectrum extends down to approximately 102 m where the fluctuations are quickly damped and disappear into the instrumental noise. Inside the PMWE layers the spectrum at smaller length scales is well fitted with a k−5/3 dependence over two decades of scales. The PMWE are therefore clearly indicative of turbulence, and the data are consistent with the turbulent dissipation of breaking gravity waves. We estimate a lower limit for the turbulent energy dissipation rate of about 10−2 W/kg in the upper (72 km layer.

  20. Measuring and improving infrastructure performance

    National Research Council Canada - National Science Library

    Committee on Measuring and Improving Infrastructure Performance, National Research Council

    .... Developing a framework for guiding attempts at measuring the performance of infrastructure systems and grappling with the concept of defining good performance are the major themes of this book...

  1. Polar winter cloud depolarization measurements with the CANDAC Rayleigh-Mie-Raman Lidar

    Science.gov (United States)

    McCullough, E. M.; Nott, G. J.; Duck, T. J.; Sica, R. J.; Doyle, J. G.; Pike-thackray, C.; Drummond, J. R.

    2011-12-01

    Clouds introduce a significant positive forcing to the Arctic radiation budget and this is strongest during the polar winter when shortwave radiation is absent (Intrieri et al., 2002). The amount of forcing depends on the occurrence probability and optical depth of the clouds as well as the cloud particle phase (Ebert and Curry 1992). Mixed-phase clouds are particularly complex as they involve interactions between three phases of water (vapour, liquid and ice) coexisting in the same cloud. Although significant progress has been made in characterizing wintertime Arctic clouds (de Boer et al., 2009 and 2011), there is considerable variability in the relative abundance of particles of each phase, in the morphology of solid particles, and in precipitation rates depending on the meteorology at the time. The Canadian Network for the Detection of Atmospheric Change (CANDAC) Rayleigh-Mie-Raman Lidar (CRL) was installed in the Canadian High Arctic at Eureka, Nunavut (80°N, 86°W) in 2008-2009. The remotely-operated system began with measurement capabilities for multi-wavelength aerosol extinction, water vapour mixing ratio, and tropospheric temperature profiles, as well as backscatter cross section coefficient and colour ratio. In 2010, a new depolarization channel was added. The capability to measure the polarization state of the return signal allows the characterization of the cloud in terms of liquid and ice water content, enabling the lidar to probe all three phases of water in these clouds. Lidar depolarization results from 2010 and 2011 winter clouds at Eureka will be presented, with a focus on differences in downwelling radiation between mixed phase clouds and ice clouds. de Boer, G., E.W. Eloranta, and M.D. Shupe (2009), Arctic mixed-phase stratiform cloud properties from multiple years of surface-based measurements at two high-latitude locations, Journal of Atmospheric Sciences, 66 (9), 2874-2887. de Boer, G., H. Morrison, M. D. Shupe, and R. Hildner (2011

  2. Performance of PV-Trombe wall in winter correlated with south facade design

    International Nuclear Information System (INIS)

    Sun, Wei; Ji, Jie; Luo, Chenglong; He, Wei

    2011-01-01

    PV-Trombe wall (PVTW) is a novel version of Trombe-wall. Photovoltaic cells on the cover glazing of the PVTW can convert solar radiation into electricity and heat simultaneously. A window on the south facade can also introduce solar heat into the room in the winter season. Experiment has been conducted to study the temperature field of a building with both southern facing window and the PVTW. A dynamic numerical model is developed for the simulation of the whole building system. The temperature of the indoor air is found to be vertically stratified from the measurement. The nodal model is adopted to calculate the temperature profile in the room. The simulation results are in good agreement with the experimental data. The different south facade designs affect the thermal efficiency of the PVTW significantly from the numerical simulation. With a southern facing window, the thermal efficiency of the PVTW is reduced by 27% relatively. The increase of PV coverage on the glazing can reduce the thermal efficiency of the TW by up to 17%. By taking account of electric conversion, the total efficiency of solar utilization is reduced by 5% at most while the glazing is fully covered with PV cells. The electric conversion efficiency of the PVTW achieves 11.6%, and is slightly affected by south facade designs.

  3. The Politics of Performance Measurement

    DEFF Research Database (Denmark)

    Bjørnholt, Bente; Larsen, Flemming

    2014-01-01

    Performance measurements are meant to improve public decision making and organizational performance. But performance measurements are far from always rational tools for problem solving, they are also political instruments. The central question addressed in this article is how performance...... impact on the political decision making process, as the focus on performance goals entails a kind of reductionism (complex problems are simplified), sequential decision making processes (with a division in separate policy issues) and short-sighted decisions (based on the need for making operational goals)....... measurement affects public policy. The aim is to conceptualize the political consequences of performance measurements and of special concern is how performance systems influence how political decisions are made, what kind of political decisions are conceivable, and how they are implemented. The literature...

  4. Diagnostic colonoscopy: performance measurement study.

    Science.gov (United States)

    Kuznets, Naomi

    2002-07-01

    This is the fifth of a series of best practices studies undertaken by the Performance Measurement Initiative (PMI), the centerpiece of the Institute for Quality Improvement (IQI), a not-for-profit quality improvement subsidiary of the Accreditation Association for Ambulatory Health Care (AAAHC) (Performance Measurement Initiative, 1999a, 1999b, 2000a, 2000b). The IQI was created to offer clinical performance measurement and improvement opportunities to ambulatory health care organizations and others interested in quality patient care. The purpose of the study was to provide opportunities to initiate clinical performance measurement on key processes and outcomes for this procedure and use this information for clinical quality improvement. This article provides performance measurement information on how organizations that have demonstrated and validated differences in clinical practice can have similar outcomes, but at a dramatically lower cost. The intent of the article is to provide organizations with alternatives in practice to provide a better value to their patients.

  5. Integrated solar water-heater and solar water cooler performance during winter time

    International Nuclear Information System (INIS)

    Shaikh, N.U.; Siddiqui, M.A

    2012-01-01

    Solar powered water heater and water cooler is an important contribution for the reduction of fossil fuel consumptions and harmful emissions to the environment. This study aims to harness the available solar potential of Pakistan and provide an option fulfilling the domestic hot and cold water demands during winter and summer seasons respectively. The system was designed for the tap-water temperature of 65 degree C (149 degree F) and the chilled drinking-water temperature of 14 degree C (57 degree F) that are the recommended temperatures by World Health Organization (WHO). The solar water heater serves one of the facilities of the Department of Mechanical Engineering at NED University of Engineering and Technology whereas, the solar water cooler will provide drinking water to approximately 50 people including both faculty and students. A pair of single glazed flat plate solar collector was installed to convert solar radiations to heat. Hot water storage and supply system was carefully designed and fabricated to obtain the designed tap-water temperature. Vapour-absorption refrigeration system was designed to chill drinking water. Intensity of solar radiations falling on the solar collector, water temperatures at the inlet and outlet of the solar collectors and the tap water temperature were measured and analyzed at different hours of the day and at different days of the month. The results show that the installed solar collector system has potential to feed hot water of temperatures ranging from 65 degree C (149 degree F) to 70 Degree C (158 degree F), that is the required hot water temperature to operate a vapour absorption chilled water production system. (author)

  6. Facilities projects performance measurement system

    International Nuclear Information System (INIS)

    Erben, J.F.

    1979-01-01

    The two DOE-owned facilities at Hanford, the Fuels and Materials Examination Facility (FMEF), and the Fusion Materials Irradiation Test Facility (FMIT), are described. The performance measurement systems used at these two facilities are next described

  7. Performance Measures, Benchmarking and Value.

    Science.gov (United States)

    McGregor, Felicity

    This paper discusses performance measurement in university libraries, based on examples from the University of Wollongong (UoW) in Australia. The introduction highlights the integration of information literacy into the curriculum and the outcomes of a 1998 UoW student satisfaction survey. The first section considers performance indicators in…

  8. Strategy Archetypes Adopted by Icelandic Companies, Their Fit with Performance Measures and Effects on Financial Performance

    DEFF Research Database (Denmark)

    Rikhardsson, Pall; Sigurjonsson, Olaf; Arnardottir, Audur Arna

    Past research seems to suggest that companies adopting certain strategies favor certain sets of performance measures. That is to say companies using entrepreneurial focused strategies favor non-financial measures or a balanced mix of financial and non-financial measures. Companies adopting reactive...... or operational strategies seem to favor financial measures and are less likely to use non-financial measures. We take this research further by focusing not only on the link between strategy types and performance measures but also on what specific performance measures are used in connection to which strategies....... Furthermore, we examine the link between the strategies adopted, the performance measures favored and the financial performance of the companies. The empirical data collection was carried out in winter 2013 with a population of the 300 largest companies in Iceland. The survey was sent to the CFO...

  9. Black carbon measurements during winter 2013-2014 in Athens and intercomparison between different techniques

    Science.gov (United States)

    Liakakou, Eleni; Stravroulas, Jason; Roukounakis, Nikolaos; Paraskevopoulou, Despina; Fourtziou, Luciana; Psiloglou, Vassilis; Gerasopoulos, Evangelos; Sciare, Jean; Mihalopoulos, Nikolaos

    2014-05-01

    Black carbon (BC) is a particulate pollutant species emitted from the combustion of fuels, biomass burning for agricultural purposes and forest fires, with the first two anthropogenic sources being the major contributors to the atmospheric burden of BC. The presence of BC is important due to its direct and indirect physicochemical effects and its use as a tracer of burning and subsequent transport processes. Black carbon measurements took place during winter 2013 -2014 in the frame of a pollution monitoring experiment conducted at the urban site of Thissio, Athens (city center) at the premises of the National Observatory of Athens. The economic crisis in Greece and the resulting turn of Athens inhabitants to wood burning for domestic heating, has led to increased daily concentrations of BC in the range of 2-6 μg m-3, peaking at night time (15-20 μg m-3). Three different optical methods were used for the determination of BC. A Particle Soot Absorption Photometer (PSAP; Radiance Research) commercial instrument was used to monitor the light absorption coefficient (σap) at 565 nm of ambient aerosols, with 1 minute resolution. During parts of the campaign, a portable Aethalometer (AE-42; Magee Scientific) was also used to provide measurement of the aerosol BC content at 7 wavelengths over 5 minutes intervals. Exploiting the measurements at different wavelengths is was feasible to separate wood burning BC from BC related to fossil fuel. Two Multi Angle Absorption Photometers (MAAP; Thermo) were also operated as reference. Finally, aerosol samples were collected on 12-hour basis using a sequential dichotomous sampler for the sampling of PM2.5, PM2.5-10and PM10 fractions of aerosols on quartz filters, and the filters were analyzed for elemental carbon (EC) by a thermal - optical transmission technique. The main objective of the study is the intercomparison of the different BC monitoring techniques under a large range of ambient concentrations achieved due to the special

  10. Insight into winter haze formation mechanisms based on aerosol hygroscopicity and effective density measurements

    Science.gov (United States)

    Xie, Yuanyuan; Ye, Xingnan; Ma, Zhen; Tao, Ye; Wang, Ruyu; Zhang, Ci; Yang, Xin; Chen, Jianmin; Chen, Hong

    2017-06-01

    We characterize a representative particulate matter (PM) episode that occurred in Shanghai during winter 2014. Particle size distribution, hygroscopicity, effective density, and single particle mass spectrometry were determined online, along with offline analysis of water-soluble inorganic ions. The mass ratio of SNA / PM1. 0 (sulfate, nitrate, and ammonium) fluctuated slightly around 0.28, suggesting that both secondary inorganic compounds and carbonaceous aerosols contributed substantially to the haze formation, regardless of pollution level. Nitrate was the most abundant ionic species during hazy periods, indicating that NOx contributed more to haze formation in Shanghai than did SO2. During the representative PM episode, the calculated PM was always consistent with the measured PM1. 0, indicating that the enhanced pollution level was attributable to the elevated number of larger particles. The number fraction of the near-hydrophobic group increased as the PM episode developed, indicating the accumulation of local emissions. Three banana-shaped particle evolutions were consistent with the rapid increase of PM1. 0 mass loading, indicating that the rapid size growth by the condensation of condensable materials was responsible for the severe haze formation. Both hygroscopicity and effective density of the particles increased considerably with growing particle size during the banana-shaped evolutions, indicating that the secondary transformation of NOx and SO2 was one of the most important contributors to the particle growth. Our results suggest that the accumulation of gas-phase and particulate pollutants under stagnant meteorological conditions and subsequent rapid particle growth by secondary processes were primarily responsible for the haze pollution in Shanghai during wintertime.

  11. Performance of biometric quality measures.

    Science.gov (United States)

    Grother, Patrick; Tabassi, Elham

    2007-04-01

    We document methods for the quantitative evaluation of systems that produce a scalar summary of a biometric sample's quality. We are motivated by a need to test claims that quality measures are predictive of matching performance. We regard a quality measurement algorithm as a black box that converts an input sample to an output scalar. We evaluate it by quantifying the association between those values and observed matching results. We advance detection error trade-off and error versus reject characteristics as metrics for the comparative evaluation of sample quality measurement algorithms. We proceed this with a definition of sample quality, a description of the operational use of quality measures. We emphasize the performance goal by including a procedure for annotating the samples of a reference corpus with quality values derived from empirical recognition scores.

  12. Aerosol optical properties measurements by a CAPS single scattering albedo monitor: Comparisons between summer and winter in Beijing, China

    Science.gov (United States)

    Han, Tingting; Xu, Weiqi; Li, Jie; Freedman, Andrew; Zhao, Jian; Wang, Qingqing; Chen, Chen; Zhang, Yingjie; Wang, Zifa; Fu, Pingqing; Liu, Xingang; Sun, Yele

    2017-02-01

    Aerosol optical properties were measured in Beijing in summer and winter using a state-of-the-art cavity attenuated phase shift single scattering albedo monitor (CAPS PMssa) along with aerosol composition measurements by aerosol mass spectrometers and aethalometers. The SSA directly measured by the CAPS PMssa showed overall agreements with those derived from colocated measurements. However, substantial differences were observed during periods with low SSA values in both summer and winter, suggesting that interpretation of low SSA values needs to be cautious. The average (±σ) extinction coefficient (bext) and absorption coefficient (bap) were 336 (±343) Mm-1 and 44 (±41) Mm-1, respectively, during wintertime, which were approximately twice those observed in summer, while the average SSA was relatively similar, 0.86 (±0.06) and 0.85 (±0.04) in summer and winter, respectively. Further analysis showed that the variations in SSA can be approximately parameterized as a function of mass fraction of secondary particulate matter (fSPM), which is SSA = 0.74 + 0.19 × fSPM (fSPM > 0.3, r2 = 0.85). The contributions of aerosol species to extinction coefficients during the two seasons were also estimated. Our results showed that the light extinction was dominantly contributed by ammonium sulfate (30%) and secondary organic aerosol (22%) in summer, while organic aerosol was the largest contributor (51%) in winter. Consistently, SPM played the major role in visibility degradation in both seasons by contributing 70% of the total extinction.

  13. Performance and carcass characteristics of steers fed with two levels of metabolizable energy intake during summer and winter season.

    Science.gov (United States)

    Arias, R A; Keim, J P; Gandarillas, M; Velásquez, A; Alvarado-Gilis, C; Mader, T L

    2018-05-22

    Climate change is producing an increase on extreme weather events around the world such as flooding, drought and extreme ambient temperatures impacting animal production and animal welfare. At present, there is a lack of studies addressing the effects of climatic conditions associated with energy intake in finishing cattle in South American feed yards. Therefore, two experiments were conducted to assess the effects of environmental variables and level of metabolizable energy intake above maintenance requirements (MEI) on performance and carcass quality of steers. In each experiment (winter and summer), steers were fed with 1.85 or 2.72 times of their requirements of metabolizable energy of maintenance. A total of 24 crossbred steers per experiment were used and located in four pens (26.25 m2/head) equipped with a Calan Broadbent Feeding System. Animals were fed with the same diet within each season, varying the amount offered to adjust the MEI treatments. Mud depth, mud scores, tympanic temperature (TT), environmental variables, average daily gain, respiration rates and carcass characteristics plus three thermal comfort indices were collected. Data analysis considered a factorial arrangement (Season and MEI). In addition, a repeated measures analysis was performed for TT and respiration rate. Mean values of ambient temperature, solar radiation and comfort thermal indices were greater in the summer experiment as expected (Pcarcass characteristics were affected by season but not by the level of MEI. Finally, due to the high variability of data as well as the small number of animals assessed in these experiments, more studies on carcass characteristics under similar conditions are required.

  14. Winter radiation extinction and reflection in a boreal pine canopy: measurements and modelling

    International Nuclear Information System (INIS)

    Pomeroy, J.W.; Dion, K.

    1996-01-01

    Predicting the rate of snow melt and intercepted snow sublimation in boreal forests requires an understanding of the effects of snow-covered conifers on the exchange of radiant energy. This study examined the amount of intercepted snow on a jack pine canopy in the boreal forest of central Saskatchewan and the shortwave and net radiation exchange with this canopy, to determine the effect of intercepted snow and canopy structure on shortwave radiation reflection and extinction and net radiation attenuation in a boreal forest. The study focused on clear sky conditions, which are common during winter in the continental boreal forest. Intercepted snow was found to have no influence on the clear-sky albedo of the canopy, the extinction of short wave radiation by the canopy or ratio of net radiation at the canopy top to that at the surface snow cover. Because of the low albedo of the snow-covered canopy, net radiation at the canopy top remains positive and a large potential source of energy for sublimation. The canopy albedo declines somewhat as the extinction efficiency of the underlying canopy increases. The extinction efficiency of short wave radiation in the canopy depends on solar angle because of the approximately horizontal orientation of pine branches. For low solar angles above the horizon, the extinction efficiency is quite low and short wave transmissivity through the canopy is relatively high. As the solar angle increases, extinction increases up to angles of about 50°, and then declines. Extinction of short wave radiation in the canopy strongly influences the attenuation of net radiation by the canopy. Short wave radiation that is extinguished by branches is radiated as long wave, partly downwards to the snow cover. The ratio of net radiation at the canopy top to that at the snow cover surface increases with the extinction of short wave radiation and is negative for low extinction efficiencies. For the pine canopy examined, the daily mean net radiation at

  15. Real time measurements of submicrometer aerosols in Seoul, Korea: Sources, characteristics, and processing of organic aerosols during winter time.

    Science.gov (United States)

    Kim, H.; Zhang, Q.

    2016-12-01

    Highly time-resolved chemical characterization of non-refractory submicrometer particulate matter (NR-PM1) was conducted in Seoul, the capital of Korea, using an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). The measurements were performed during winter when persistent air quality problems associated with elevated PM concentrations were observed. The average NR-PM1 concentration was 27.5 µg m-3 and the average mass was dominated by organics (44%), followed by nitrate (24%) and sulfate (10%). Five distinct sources of organic aerosol (OA) were identified from positive matrix factorization (PMF) analysis of the AMS data: vehicle emissions represented by a hydrocarbon-like OA factor (HOA), cooking represented by a cooking OA factor (COA), wood combustion represented by a biomass burning OA factor (BBOA), and secondary aerosol formation in the atmosphere that is represented by a semi-volatile oxygenated OA factor (SVOOA) and a low volatile oxygenated OA factor (LVOOA). These factors, on average, contributed 16, 20, 23, 15 and 26% to the total OA mass, respectively, with primary organic aerosol (POA = HOA + COA + BBOA) accounting for 59% of the OA mass. On average, both primary emissions and secondary aerosol formation are important factors affecting air quality in Seoul during winter, contributing approximately equal. However, differences in the fraction of PM source and properties were observed between high and low loading PM period. For example, during stagnant period with low wind speed (WS) (0.99 ± 0.7 m/s) and high RH (71%), high PM loadings (43.6 ± 12.4 µg m-3) with enhanced fractions of nitrate (27%) and SVOOA (8%) were observed, indicating a strong influence from locally generated secondary aerosol. On the other hand, when low PM loadings (12.6 ± 7.1 µg m-3), which were commonly associated with high WS (1.8 ± 1.1 m/s) and low RH (50 %), were observed, the fraction of regional sources, such as sulfate (12%) and LVOOA (21

  16. Effect of ventilation regimen on the welfare and production performance of the lactating ewe in winter

    Directory of Open Access Journals (Sweden)

    L. Taibi

    2011-03-01

    Full Text Available The importance of efficient ventilation systems of animal houses is often underestimated during the winter season and this may result in a serious limitation to high efficiencies of production and good health of farmed livestock. Poor ventilation may lead to high levels of gaseous pollutants as well as to increased moisture content of the house air and condensation on internal surfaces. Both events may enhance the growth and multiplication of microorganisms in the air and in the litter (Sevi et al., 2001...

  17. Scalable Performance Measurement and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Gamblin, Todd [Univ. of North Carolina, Chapel Hill, NC (United States)

    2009-01-01

    Concurrency levels in large-scale, distributed-memory supercomputers are rising exponentially. Modern machines may contain 100,000 or more microprocessor cores, and the largest of these, IBM's Blue Gene/L, contains over 200,000 cores. Future systems are expected to support millions of concurrent tasks. In this dissertation, we focus on efficient techniques for measuring and analyzing the performance of applications running on very large parallel machines. Tuning the performance of large-scale applications can be a subtle and time-consuming task because application developers must measure and interpret data from many independent processes. While the volume of the raw data scales linearly with the number of tasks in the running system, the number of tasks is growing exponentially, and data for even small systems quickly becomes unmanageable. Transporting performance data from so many processes over a network can perturb application performance and make measurements inaccurate, and storing such data would require a prohibitive amount of space. Moreover, even if it were stored, analyzing the data would be extremely time-consuming. In this dissertation, we present novel methods for reducing performance data volume. The first draws on multi-scale wavelet techniques from signal processing to compress systemwide, time-varying load-balance data. The second uses statistical sampling to select a small subset of running processes to generate low-volume traces. A third approach combines sampling and wavelet compression to stratify performance data adaptively at run-time and to reduce further the cost of sampled tracing. We have integrated these approaches into Libra, a toolset for scalable load-balance analysis. We present Libra and show how it can be used to analyze data from large scientific applications scalably.

  18. Measuring performance at trade shows

    DEFF Research Database (Denmark)

    Hansen, Kåre

    2004-01-01

    Trade shows is an increasingly important marketing activity to many companies, but current measures of trade show performance do not adequately capture dimensions important to exhibitors. Based on the marketing literature's outcome and behavior-based control system taxonomy, a model is built...... that captures a outcome-based sales dimension and four behavior-based dimensions (i.e. information-gathering, relationship building, image building, and motivation activities). A 16-item instrument is developed for assessing exhibitors perceptions of their trade show performance. The paper presents evidence...

  19. Performance of winter-rapeseed lines with an improved fatty acid composition

    International Nuclear Information System (INIS)

    Kraeling, K.

    1990-01-01

    Full text: High levels of linoleic (C18:2) and low content of linolenic acid (C18:3) are desired traits for rapeseed. Induced mutants with an improved fatty acid composition derived from the spring-rapeseed variety Oro were crossed with a winter-rapeseed line exhibiting an increased C18:2 content and backcrossed two times with several high yielding cultivars of winter-rapeseed. After each cross the F 2 was screened by gaschromatography for the mutant-type. After the second backcross from each of 118 lines (BC 2 -F 3 ) an observation plot (9.4 m 2 ) was sown. Results show that through backcrossing it was possible to develop lines with a high proportion of C18:2 and a reduced level of C18:3, whereas C18:1 remained unchanged, demonstrating new combinations different from the usual positive correlation between C18:2 and C18:3. Yield increased continuously with decreasing portion of the mutant genome. Relatively low genotype x location interaction for fatty acids was found. (author)

  20. Performance Measurement of Research Activitities

    DEFF Research Database (Denmark)

    Jakobsen, Morten; Jensen, Tina Blegind; Peyton, Margit Malmmose

    Performance measurements have made their entry into the world of universities. Every research activity is registered in a database and the output measures form the foundation for managerial decisions. The purpose of this chapter is to investigate the registration practices among researchers...... the registrations as a way to be promoted and to legitimise and account for their work; on the other hand, the economic incentives behind ranking lists and bibliographic research indicators threaten the individual researcher's freedom. The findings also show how managers have difficulties in translating back...

  1. Vertical gradients of nitrous acid (HONO) measured in Beijing during winter smog events.

    Science.gov (United States)

    Kramer, Louisa; Crilley, Leigh; Thomson, Steven; Bloss, William; Tong, Shengrui

    2017-04-01

    HONO is an important atmospheric constituent, as the photolysis of HONO leads to the formation of OH radicals in the boundary layer, with contributions of up to 60% in urban regions. This is particularly important in mega-cities, such as Beijing, where measured HONO levels can reach parts per billion. Research has shown that direct emissions, homogeneous gas phase reactions and heterogeneous conversion of NO2 on surfaces all contribute to HONO in urban areas. There are, however, still uncertainties regarding the magnitude of these sources, and models are still unable to account for total measured HONO mixing ratios. To assess the sources of HONO, vertical profile measurements were performed up to an altitude of 260 m on the Institute of Atmospheric Physics (IAP) Meteorological Tower in Beijing. These measurements were performed as part of the Air Pollution and Human Health (APHH) project, during Nov/Dec 2016. Here we present HONO profile measurements using a long-path absorption photometer (LOPAP), during both clear and hazy days. HONO levels near the ground were very high during smog events with concentrations over 10 ppb observed. The data show a strong negative gradient with altitude, suggesting a source close to the surface. The largest gradients were observed overnight during smog events, with differences in HONO between the ground and the highest level up to 6 ppb.

  2. From performance measurement to learning

    DEFF Research Database (Denmark)

    Lewis, Jenny; Triantafillou, Peter

    2012-01-01

    Over the last few decades accountability has accommodated an increasing number of different political, legal and administrative goals. This article focuses on the administrative aspect of accountability and explores the potential perils of a shift from performance measurement to learning. While...... overload. We conclude with some comments on limiting the undesirable consequences of such a move. Points for practitioners Public administrators need to identify and weigh the (human, political and economic) benefits and costs of accountability regimes. While output-focused performance measurement regimes...... to comply with accountability requirements, because of the first point. Third, the costs of compliance are likely to increase because learning requires more participation and dialogue. Fourth, accountability as learning may generate a ‘change for the sake of change’ mentality, creating further government...

  3. Aircraft and ground vehicle friction measurements obtained under winter runway conditions

    Science.gov (United States)

    Yager, Thomas J.

    1989-01-01

    Tests with specially instrumented NASA B-737 and B-727 aircraft together with several different ground friction measuring devices have been conducted for a variety of runway surface types and wetness conditions. This effort is part of the Joint FAA/NASA Aircraft/Ground Vehicle Runway Friction Program aimed at obtaining a better understanding of aircraft ground handling performance under adverse weather conditions, and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow-, and ice-covered runway conditions is discussed together with ground vehicle friction data obtained under similar runway conditions. For the wet, compacted snow- and ice-covered runway conditions, the relationship between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, and surface contaminant-type are discussed. The test results indicate that use of properly maintained and calibrated ground vehicles for monitoring runway friction conditions should be encouraged particularly under adverse weather conditions.

  4. Comparison of mesoscale model and tower measurements of surface fluxes during Winter Icing and Storms Program/Atmospheric Radiation Measurement 91

    International Nuclear Information System (INIS)

    Oncley, S.P.; Dudhia, J.

    1994-01-01

    This study is an evaluation of the ability of the Pennsylvania State University/National Center for Atmospheric Research (NCAR) mesoscale model (MM4) to determine surface fluxes to see if measured fluxes should be assimilated into model runs. Fluxes were compared from a high-resolution (5 km grid spacing) MM4 run during one day of the Winter Icing and Storms Programs/Atmospheric Radiation Measurement (WISP/ARM) experiment (over NE Colorado in winter 1991) with direct flux measurements made from a tower over a representative site by a three-dimensional sonic anemometer and fast response temperature and humidity sensors. This tower was part of the NCAR Atmosphere-Surface Turbulent Exchange Research (ASTER) facility. Also, mean values were compared to check whether any differences were due to the model parameterization or model variables

  5. Opcode counting for performance measurement

    Energy Technology Data Exchange (ETDEWEB)

    Gara, Alan; Satterfield, David L.; Walkup, Robert E.

    2018-03-20

    Methods, systems and computer program products are disclosed for measuring a performance of a program running on a processing unit of a processing system. In one embodiment, the method comprises informing a logic unit of each instruction in the program that is executed by the processing unit, assigning a weight to each instruction, assigning the instructions to a plurality of groups, and analyzing the plurality of groups to measure one or more metrics. In one embodiment, each instruction includes an operating code portion, and the assigning includes assigning the instructions to the groups based on the operating code portions of the instructions. In an embodiment, each type of instruction is assigned to a respective one of the plurality of groups. These groups may be combined into a plurality of sets of the groups.

  6. Performance measurement and pay for performance

    NARCIS (Netherlands)

    Tuijl, van H.F.J.M.; Kleingeld, P.A.M.; Algera, J.A.; Rutten, M.L.; Sonnentag, S.

    2002-01-01

    This chapter, which takes a (re)design perspective, focuses on the management of employees’ contributions to organisational goal attainment. The control loop for the self-regulation of task performance is used as a frame of reference. Several subsets of design requirements are described and related

  7. RESEARCHES REGARDING THE TECHNOLOGICAL PERFORMANCES OF CARP REARING DURING WINTER PERIOD IN THE CONDITIONS OF A RECIRCULATING AQUACULTURE SYSTEM

    Directory of Open Access Journals (Sweden)

    G. STEFAN

    2008-10-01

    Full Text Available The techniques of carp culture are highly diversified, ranging from the extensive production in pond or open water with no fertilization or supplemental feeding to highly intensive systems in concrete tanks or cages. Among the different carp species, common carp is the best species reared in intensive monoculture, the others (Chinese and Indian carps being usually cultivated in polyculture (P. Kestemont, 1995. An experiment was conducted in inside recirculation system conditions to identify the technological performances on carp growth and survival at the Fishing and Aquaculture Department, Galati, during winter period (February, 2007 – March, 2007. The 1-year-old carp (Cyprinus carpio 4792g; 4594 g; 4561 g and 4525 g (total weight grew to 7384g; 7017g; 6924g and 7125 g in 44 days in aquarium 1, 2, 3 and 4, respectively. In all aquariums, the fish appeared healthy and no mortality was observed. Feed conversion efficiencies (FCE had similar values among all aquariums, the highest FCE being found in B4 aquarium with 1, 57 value. Water quality parameters were acceptable range for fish culture. Results show that the carp rearing during winter period in the inside recirculation system is a very good economic solution.

  8. PERFORMANCE OF ‘NANICÃO JANGADA’ BANANA PLANTS INTERCROPPED WITH WINTER COVER CROPS

    Directory of Open Access Journals (Sweden)

    RICARDO SFEIR DE AGUIAR

    Full Text Available ABSTRACT The use of cover crops species may be an important strategy in the pursuit of sustainability of agroecosystems, considering benefits to soil, such as improvements of physical and chemical characteristics, and weed control. The objective of this study was to evaluate the effect of winter cover crops and other soil managements on chemical soil properties, on the cycle, on the production of the first cycle and on the fruit quality of banana cv. Nanicão Jangada in Andirá – PR, Brazil. The experiment was carried out in a commercial. Planting of banana suckers from the grower area occurred in the first half of March 2011, with a spacing of 2.40 m between rows and 1.90 m between plants. The experiment was designed in randomized blocks with four replications and six plants per plot. The six treatments were: black oat (Avenastrigosa Schreb, forage turnip (Raphanus sativus L. var. oleiferus, consortium of black oat and forage turnip, chicken litter, residues of banana plants, and bare ground. The evaluations were vegetative development and life cycle of banana plants, yield and quality of fruits, soil chemical characterstics, and fresh and dry mass of green manures. The results were submitted to ANOVA (F Test, and Tukey test at 5 % probability. Black oat and black oat with forage turnip consortium were superior in biomass production. Systems of soil management had no effect on the variables, except in the periods between planting and flowering and between planting and harvest, which were shorter in the treatment of soil management with crop residues, longer in the treatment with forage turnip, and intermediate in the other treatments.

  9. Testing our understanding of Arctic denitrification using MIPAS-E satellite measurements in winter 2002/2003

    Directory of Open Access Journals (Sweden)

    S. Davies

    2006-01-01

    Full Text Available Observations of gas-phase HNO3 and N2O in the polar stratosphere from the Michelson Interferometer for Passive Atmospheric Sounding aboard the ENVISAT satellite (MIPAS-E were made during the cold Arctic winter of 2002/2003. Vortex temperatures were unusually low in early winter and remained favourable for polar stratospheric cloud formation and denitrification until mid-January. MIPAS-E observations provide the first dataset with sufficient coverage of the polar vortex in mid-winter which enables a reasonable estimate of the timing of onset and spatial distribution of denitrification of the Arctic lower stratosphere to be performed. We use the observations from MIPAS-E to test the evolution of denitrification in the DLAPSE (Denitrification by Lagrangian Particle Sedimentation microphysical denitrification model coupled to the SLIMCAT chemical transport model. In addition, the predicted denitrification from a simple equilibrium nitric acid trihydrate-based scheme is also compared with MIPAS-E. Modelled denitrification is compared with in-vortex NOy and N2O observations from the balloon-borne MarkIV interferometer in mid-December. Denitrification was clearly observed by MIPAS-E in mid-December 2002 and reached 80% in the core of the vortex by early January 2003. The DLAPSE model is broadly able to capture both the timing of onset and the spatial distribution of the observed denitrification. A simple thermodynamic equilibrium scheme is able to reproduce the observed denitrification in the core of the vortex but overestimates denitrification closer to the vortex edge. This study also suggests that the onset of denitrification in simple thermodynamic schemes may be earlier than in the MIPAS-E observations.

  10. Performance measurement for information systems: Industry perspectives

    Science.gov (United States)

    Bishop, Peter C.; Yoes, Cissy; Hamilton, Kay

    1992-01-01

    Performance measurement has become a focal topic for information systems (IS) organizations. Historically, IS performance measures have dealt with the efficiency of the data processing function. Today, the function of most IS organizations goes beyond simple data processing. To understand how IS organizations have developed meaningful performance measures that reflect their objectives and activities, industry perspectives on IS performance measurement was studied. The objectives of the study were to understand the state of the practice in IS performance techniques for IS performance measurement; to gather approaches and measures of actual performance measures used in industry; and to report patterns, trends, and lessons learned about performance measurement to NASA/JSC. Examples of how some of the most forward looking companies are shaping their IS processes through measurement is provided. Thoughts on the presence of a life-cycle to performance measures development and a suggested taxonomy for performance measurements are included in the appendices.

  11. 45 CFR 305.2 - Performance measures.

    Science.gov (United States)

    2010-10-01

    ... PROGRAM PERFORMANCE MEASURES, STANDARDS, FINANCIAL INCENTIVES, AND PENALTIES § 305.2 Performance measures. (a) The child support incentive system measures State performance levels in five program areas... 45 Public Welfare 2 2010-10-01 2010-10-01 false Performance measures. 305.2 Section 305.2 Public...

  12. Chemical ozone losses in Arctic and Antarctic polar winter/spring season derived from SCIAMACHY limb measurements 2002–2009

    Directory of Open Access Journals (Sweden)

    T. Sonkaew

    2013-02-01

    Full Text Available Stratospheric ozone profiles are retrieved for the period 2002–2009 from SCIAMACHY measurements of limb-scattered solar radiation in the Hartley and Chappuis absorption bands of ozone. This data set is used to determine the chemical ozone losses in both the Arctic and Antarctic polar vortices by averaging the ozone in the vortex at a given potential temperature. The chemical ozone losses at isentropic levels between 450 K and 600 K are derived from the difference between observed ozone abundances and the ozone modelled taking diabatic cooling into account, but no chemical ozone loss. Chemical ozone losses of up to 30–40% between mid-January and the end of March inside the Arctic polar vortex are reported. Strong inter-annual variability of the Arctic ozone loss is observed, with the cold winters 2004/2005 and 2006/2007 showing chemical ozone losses inside the polar vortex at 475 K, where 1.7 ppmv and 1.4 ppmv of ozone were removed, respectively, over the period from 22 January to beginning of April and 0.9 ppmv and 1.2 ppmv, respectively, during February. For the winters of 2007/2008 and 2002/2003, ozone losses of about 0.8 ppmv and 0.4 ppmv, respectively are estimated at the 475 K isentropic level for the period from 22 January to beginning of April. Essentially no ozone losses were diagnosed for the relatively warm winters of 2003/2004 and 2005/2006. The maximum ozone loss in the SCIAMACHY data set was found in 2007 at the 600 K level and amounted to about 2.1 ppmv for the period between 22 January and the end of April. Enhanced losses close to this altitude were found in all investigated Arctic springs, in contrast to Antarctic spring. The inter-annual variability of ozone losses and PSC occurrence rates observed during Arctic spring is consistent with the known QBO effects on the Arctic polar vortex, with exception of the unusual Arctic winter 2008/2009.

    The maximum total ozone mass loss of about 25 million tons was found in the

  13. Experimental study and performance analysis of a thermoelectric cooling and heating system driven by a photovoltaic/thermal system in summer and winter operation modes

    International Nuclear Information System (INIS)

    He, Wei; Zhou, JinZhi; Chen, Chi; Ji, Jie

    2014-01-01

    Highlights: • Thermoelectric heating system driven by heat pipe PV/T system was built and test. • Theoretical analysis has been done and simulation results have been validated by experiments. • The energetic efficiency and exergetic efficiency in summer and winter operation mode was analyzed and compared. - Abstract: This paper presents theoretical and experimental investigations of the winter operation mode of a thermoelectric cooling and heating system driven by a heat pipe photovoltaic/thermal (PV/T) panel. And the energy and exergy analysis of this system in summer and winter operation modes are also done. The winter operation mode of this system is tested in an experimental room which temperature is controlled at 18 °C. The results indicate the average coefficient of performance (COP) of thermoelectric module of this system can be about 1.7, the electrical efficiency of the PV/T panel can reach 16.7%, and the thermal efficiency of this system can reach 23.5%. The energy and exergy analysis show the energetic efficiency of the system in summer operation mode is higher than that of it in winter operation mode, but the exergetic efficiency in summer operation mode is lower than that in winter operation mode, on the contrary

  14. Winter Radiation Extinction and Reflection in a Boreal Pine Canopy: Measurements and Modelling

    Science.gov (United States)

    Pomeroy, J. W.; Dion, K.

    1996-12-01

    Predicting the rate of snowmelt and intercepted snow sublimation in boreal forests requires an understanding of the effects of snow-covered conifers on the exchange of radiant energy. This study examined the amount of intercepted snow on a jack pine canopy in the boreal forest of central Saskatchewan and the shortwave and net radiation exchange with this canopy, to determine the effect of intercepted snow and canopy structure on shortwave radiation reflection and extinction and net radiation attenuation in a boreal forest. The study focused on clear sky conditions, which are common during winter in the continental boreal forest. Intercepted snow was found to have no influence on the clear-sky albedo of the canopy, the extinction of short wave radiation by the canopy or ratio of net radiation at the canopy top to that at the surface snow cover. Because of the low albedo of the snow-covered canopy, net radiation at the canopy top remains positive and a large potential source of energy for sublimation. The canopy albedo declines somewhat as the extinction efficiency of the underlying canopy increases. The extinction efficiency of short wave radiation in the canopy depends on solar angle because of the approximately horizontal orientation of pine branches. For low solar angles above the horizon, the extinction efficiency is quite low and short wave transmissivity through the canopy is relatively high. As the solar angle increases, extinction increases up to angles of about 50̂, and then declines. Extinction of short wave radiation in the canopy strongly influences the attenuation of net radiation by the canopy. Short wave radiation that is extinguished by branches is radiated as long wave, partly downwards to the snow cover. The ratio of net radiation at the canopy top to that at the snow cover surface increases with the extinction of short wave radiation and is negative for low extinction efficiencies. For the pine canopy examined, the daily mean net radiation at the

  15. Brush seal performance measurement system

    OpenAIRE

    Aksoy, Serdar; Akşit, Mahmut Faruk; Aksit, Mahmut Faruk; Duran, Ertuğrul Tolga; Duran, Ertugrul Tolga

    2009-01-01

    Brush seals are rapidly replacing conventional labyrinth seals in turbomachinery applications. Upon pressure application, seal stiffness increases drastically due to frictional bristle interlocking. Operating stiffness is critical to determine seal wear life. Typically, seal stiffness is measured by pressing a curved shoe to brush bore. The static-unpressurized measurement is extrapolated to pressurized and high speed operating conditions. This work presents a seal stiffness measurement syste...

  16. Comparison of subjective symptoms and cold prevention measures in winter between traffic control workers and construction workers in Japan.

    Science.gov (United States)

    Inaba, Ryoichi; Kurokawa, Junichi; Mirbod, Seyed Mohammad

    2009-07-01

    To help making comfortable workplaces and to prevent health disorders induced by the exposure to moderate cold in two different groups of out-door workers, we conducted a survey to compare subjective symptoms and cold prevention measures in winter between traffic control workers and construction workers. The subjects of this study were 98 male traffic control workers and 149 male workers engaged in building construction. Work loads of traffic control workers and construction workers were estimated at RMR1-2 and RMR2-4, respectively. All subjects were asked to complete a self-administered questionnaire covering age, occupational career, working figure, present illness, past history of diseases, individual preventive measures to the cold, subjective symptoms in the winter (43 items) and subjective symptoms occurred during daytime working in the winter (6 items). In two parts of the construction workplaces (the place where a morning assembly was held and on the 7th floor of the construction site) dry bulb, wet bulb and globe temperatures were measured in January. Windchill Index (kcal/cm,(2) x h) was calculated by the measured dry bulb temperature and wind velocity. Mean values of dry bulb temperature between 9:00 and 16:30 in the place where a morning assembly was held for three days were between 4.8 +/- 1.2 degrees C at 9:00 am and 9.3 +/- 1.1 degrees C at noon. Mean values of Windchill Index in the place where a morning assembly was held were between 490.8+/-23.9 kcal/cm(2) x h at 9:30 am and 608.2+/-47.3 kcal/cm(2) x h at 2:30 pm. Occupational career, monthly working days, daily working hours, one way commuting hours, and daily smoking numbers of the traffic control workers were significantly shorter than the construction workers (pconstruction workers (0.7%). Prevalence of wearing a warm underwear, body warmer, warm trousers, underpants, warm socks, shoe warmer and muffler in the traffic control workers were significantly higher than the construction workers. The

  17. Assessment of the Performance of Several Roadway Mixes under Rain, Snow, and Winter Maintenance Activities

    OpenAIRE

    Flintsch, Gerardo W.

    2004-01-01

    The purpose of this study was to assess the relative functional performance, including skid resistance and splash and spray, of five hot-mix-asphalt (HMA) surfaces and a tinned portland cement concrete highway surface during controlled wet and wintry weather events. The study compared the way that these surfaces respond to various deicing and anti-icing snow removal and ice control techniques under artificial wintry conditions. In addition, the splash and spray characteristics of the surfaces...

  18. Automated vehicle location, data recording, friction measurement and applicator control for winter road maintenance.

    Science.gov (United States)

    2010-02-01

    The first part of this project conducted a detailed evaluation of the ability of a new friction measurement system to : provide an accurate measure of road conditions. A system that records friction coefficient as a function of road : location was de...

  19. Vitamin D Level in Summer and Winter Related to Measured UVR Exposure and Behavior

    DEFF Research Database (Denmark)

    Thieden, E.; Philipsen, P.A.; Heydenreich, J.

    2009-01-01

    , electronic wristwatch UVR dosimeters and sun exposure diaries. Constitutive and facultative skin pigmentation was measured in September. 25(OH) D was measured in September and February and was in mean 82 nmol/L +/- 25 (mean +/- SD) in September and 56 nmol/L +/- 19 (mean +/- SD) in February. The received...

  20. Analysis of winter climate simulations performed with ARPEGE-Climat (T63) in the framework of PROVOST

    Energy Technology Data Exchange (ETDEWEB)

    Parey, S.; Dichampt-Martineu, Ch.; Caneill, J.Y. [Electricite de France, 78 - Chatou (France). Research Branch, Environment

    1997-12-01

    The interest of EDF for seasonal forecasting is a consequence of the high sensitivity of electricity consumption to temperature, especially during the winter season. That is why the Research branch of EDF is involved in the PROVOST project (PRediction Of climate Variations On Seasonal and inter-annual Timescales). Two sets of simulations are studied. The first one was calculated apart from the PROVOST experiments with the LMD model covering the 1970 to 1992 winters with eleven simulations per winter. The second one was calculated at EDF in the framework of PROVOST with ARPEGE-Climat model, covering the 1979 to 1994 winters (nine simulations per winter). The probabilistic formulation of climatic scenarios in function of the seasonal simulations with ARPEGE-Climat gives good results if the monthly mean temperature is taken into account. (R.P.) 3 refs.

  1. Prenatal famine, birthweight, reproductive performance and age at menopause: the Dutch hunger winter families study.

    Science.gov (United States)

    Yarde, F; Broekmans, F J M; van der Pal-de Bruin, K M; Schönbeck, Y; te Velde, E R; Stein, A D; Lumey, L H

    2013-12-01

    Is there an association between acute prenatal famine exposure or birthweight and subsequent reproductive performance and age at menopause? No association was found between intrauterine famine exposure and reproductive performance, but survival analysis showed that women exposed in utero were 24% more likely to experience menopause at any age. Associations between prenatal famine and subsequent reproductive performance have been examined previously with inconsistent results. Evidence for the effects of famine exposure on age at natural menopause is limited to one study of post-natal exposure. This cohort study included men and women born around the time of the Dutch famine of 1944-1945. The study participants (n = 1070) underwent standardized interviews on reproductive parameters at a mean age of 59 years. The participants were grouped as men and women with prenatal famine exposure (n = 407), their same-sex siblings (family controls, n = 319) or other men and women born before or after the famine period (time controls, n = 344). Associations of famine exposure with reproductive performance and menopause were analysed using logistic regression and survival analysis with competing risk, after controlling for family clustering. Gestational famine exposure was not associated with nulliparity, age at birth of first child, difficulties conceiving or pregnancy outcome (all P> 0.05) in men or women. At any given age, women were more likely to experience menopause after gestational exposure to famine (hazard ratio 1.24; 95% CI 1.03, 1.51). The association was not attenuated with an additional control for a woman's birthweight. In this study, there was no association between birthweight and age at menopause after adjustment for gestational famine exposure. Age at menopause was self-reported and assessed retrospectively. The study power to examine associations with specific gestational periods of famine exposure and reproductive function was limited. Our findings support

  2. A study of energy performance and audit of commercial mall in hot-summer/warm-winter climate zone in China

    Energy Technology Data Exchange (ETDEWEB)

    Zhisheng, Li; Jiawen, Liao; Xiaoxia, Wang [School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou, Guangdong, 510006 (China); Lin, Yaolin [Building Energy Solutions and Technologies, Inc, San Jose Office, San Jose, CA 95134 (United States); Xuhong, Liu [School of Architecture and Urban Planning, Guangdong University of Technology, Guangzhou, Guangdong, 510643 (China)

    2013-08-15

    The building energy performance improvement of large-scale public buildings is very important to release China's energy shortage pressure. The aim of the study is to find out the building energy saving potentials of large-scale public and commercial buildings by energy audit. In this paper, the energy consumption, energy performance, and audit were carried out for a typical commercial mall, the so-called largest mall in Asia, located in a hot-summer and warm-winter climate zone. The total annual energy consumption reaches 210.01 kWh/m{sup 2}, of which lighting energy consumption accounts for 30.03 kWh/m{sup 2} and the lift and elevator energy consumption accounts for 40.46 kWh/m{sup 2}. It is by far higher than that of the average building energy consumption in the same category. However, the annual heating, ventilation, and air-conditioning (HVAC) energy consumption is only 87.19 kWh/m{sup 2} even though they run 24/7. It proves that the energy performance of the HVAC system is good. Therefore, the building energy savings potential mainly relies on reducing the excessive usage of lighting, lifts, and elevators.

  3. Evolutionary Effects on Morphology and Agronomic Performance of Three Winter Wheat Composite Cross Populations Maintained for Six Years under Organic and Conventional Conditions

    Directory of Open Access Journals (Sweden)

    Sarah Brumlop

    2017-02-01

    Full Text Available Three winter wheat (Triticum aestivum L. composite cross populations (CCPs that had been maintained in repeated parallel populations under organic and conventional conditions from the F5 to the F10 were compared in a two-year replicated field trial under organic conditions. The populations were compared to each other, to a mixture of the parental varieties used to establish the CCPs, and to three winter wheat varieties currently popular in organic farming. Foot and foliar diseases, straw length, ear length, yield parameters, and baking quality parameters were assessed. The overall performance of the CCPs differed clearly from each other due to differences in their parental genetics and not because of their conventional or organic history. The CCPs with high yielding background (YCCPs also yielded higher than the CCPs with a high baking quality background (QCCPs; in the absence of extreme winter stress. The QCCPs performed equally well in comparison to the reference varieties, which were also of high baking quality. Compared to the parental mixture the CCPs proved to be highly resilient, recovering much better from winter kill in winter 2011/12. Nevertheless, they were out yielded by the references in that year. No such differences were seen in 2013, indicating that the CCPs are comparable with modern cultivars in yielding ability under organic conditions. We conclude that—especially when focusing on traits that are not directly influenced by natural selection (e.g. quality traits—the choice of parents to establish a CCP is crucial. In the case of the QCCPs the establishment of a reliable high-quality population worked very well and quality traits were successfully maintained over time. However, in the YCCPs lack of winter hardiness in the YCCP parents also became clearly visible under relevant winter conditions.

  4. Mobility and reliability performance measurement.

    Science.gov (United States)

    2013-06-01

    This project grew out of the fact that mobility was identified early on as one of the key performance focus areas of NCDOTs : strategic transformation effort. The Transformation Management Team (TMT) established a TMT Mobility Workstream Team : in...

  5. Traffic Management Systems Performance Measurement: Final Report

    OpenAIRE

    Banks, James H.; Kelly, Gregory

    1997-01-01

    This report documents a study of performance measurement for Transportation Management Centers (TMCs). Performance measurement requirements were analyzed, data collection and management techniques were investigated, and case study traffic data system improvement plans were prepared for two Caltrans districts.

  6. Performance measurement and insurance liabilities

    NARCIS (Netherlands)

    Plantinga, A; Huijgen, C

    2001-01-01

    In this article, the authors develop an attribution framework for evaluating the investment performance of institutional investors such as insurance companies. The model is useful in identifying the investment skills of insurance companies. This is accomplished by developing a dual benchmark for the

  7. Tethered balloon operation for wintering aerosol measurements in the lower troposphere at Syowa Station, Antarctica

    OpenAIRE

    Keiichiro Hara; Kazuo Osada; Takashi Yamanouchi

    2007-01-01

    The 46th Japanese Antarctic Research Expedition (JARE-46) carried out twenty seven tethered-balloon-borne aerosol measurements at Syowa Station for better understanding of aerosol chemical and physical properties in the lower troposphere from 6th January 2005 until 11 December 2005. This report summarizes the plan, preparation, field activities and some troubles/problems in the tethered-balloon observations.

  8. Eva versus Other Performance Measures

    OpenAIRE

    Hechmi Soumaya

    2013-01-01

    Create value not only intended to satisfy shareholders. This is also the way to ensure the ability of the company to ensure its sustainability and finance its growth. The company will not attract new capital if it destroys value. "The concept of value creation is none other than the intersection of strategy (create value) and technique (evaluate the company)"(Powilewicz, 2002). The basic idea behind the different measures of value creation by a company is that a company creates value for its ...

  9. Tethered balloon operation for wintering aerosol measurements in the lower troposphere at Syowa Station, Antarctica

    Directory of Open Access Journals (Sweden)

    Keiichiro Hara

    2007-03-01

    Full Text Available The 46th Japanese Antarctic Research Expedition (JARE-46 carried out twenty seven tethered-balloon-borne aerosol measurements at Syowa Station for better understanding of aerosol chemical and physical properties in the lower troposphere from 6th January 2005 until 11 December 2005. This report summarizes the plan, preparation, field activities and some troubles/problems in the tethered-balloon observations.

  10. Internet Performance and Reliability Measurements

    International Nuclear Information System (INIS)

    Cottrell, Les

    2003-01-01

    Collaborative HEP research is dependent on good Internet connectivity. Although most local- and wide-area networks are carefully watched, there is little monitoring of connections that cross many networks. This paper describes work in progress at several sites to monitor Internet end-to-end performance between hundreds of HEP sites worldwide. At each collection site, ICMP ping packets are automatically sent periodically to sites of interest. The data is recorded and made available to analysis nodes, which collect the data from multiple collection sites and provide analysis and graphing. Future work includes improving the efficiency and accuracy of ping data collection

  11. An hour of bright white light in the early morning improves performance and advances sleep and circadian phase during the Antarctic winter.

    Science.gov (United States)

    Corbett, R W; Middleton, B; Arendt, J

    2012-09-13

    Previous work has demonstrated that exposure to an hour of bright light in the morning and the evening during the Polar winter has beneficial effects on circadian phase. This study investigated the effect of a single hour of bright white morning light on circadian phase, sleep, alertness and cognitive performance. Nine individuals (eight male, one female, median age 30 years), wintering at Halley Research Station (75°S), Antarctica from 7th May until 6th August 2007, were exposed to bright white light for a fortnight from 08:30 to 09:30 h, with two fortnight control periods on either side. This sequence was performed twice, before and following Midwinter. Light exposure, sleep and alertness were assessed daily by actigraphy, sleep diaries and subjective visual analogue scales. Circadian phase (assessed by urinary 6-sulphatoxymelatonin rhythm) and cognitive performance were evaluated at the end of each fortnight. During light exposure circadian phase was advanced from 4.97 ± 0.96 decimal hours (dh) (mean ± SD) to 4.08 ± 0.68 dh (p = 0.003). Wake-up time was shifted by a similar margin from 8.45 ± 1.83 dh to 7.59 ± 0.78 dh (p < 0.001). Sleep start time was also advanced (p = 0.047) but by a lesser amount, consequently, actual sleep time was slightly reduced. There was no change in objective or subjective measures of sleep quality or subjective measures of alertness. An improvement in cognitive performance was found with both the Single Letter Cancellation Test (p < 0.001) and the Digit Symbol Substitution Test (p = 0.026) with preserved circadian variation. These beneficial effects of a single short duration light treatment may have implications not only for the Antarctic but other remote environments where access to natural light and delayed circadian phase, is problematic. These results require validation in larger studies at varying locations. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  12. Vegetative, productive and qualitative performance of grapevine "Cabernet Sauvignon" according to the use of winter cover crops

    OpenAIRE

    Bettoni, Jean Carlos; Feldberg, Nelson Pires; Nava, Gilberto; Veiga, Milton da; Wildner, Leandro do Prado

    2016-01-01

    ABSTRACT To study the effect of winter cover crops on the vegetative, productive and qualitative behavior of "Cabernet Sauvignon" grapevines, an experiment was conducted in two wine harvests by sowing different species of winter cover crops and additional treatments with manual weeding and mechanical mowing in an experimental vineyard located at the Experimental Station of Epagri in Videira, state of Santa Catarina, Brazil. Plant attributes of the grapevine, such as number of rods and weight ...

  13. Potential denitrification in arable soil samples at winter temperatures - measurements by 15N gas analysis

    International Nuclear Information System (INIS)

    Lippold, H.; Foerster, I.; Matzel, W.

    1989-01-01

    In samples from the plough horizon of five soils taken after cereal harvest, denitrification was measured as volatilization of N 2 and N 2 O from 15 N nitrate in the absence of O 2 . Nitrate contents lower than 50 ppm N (related to soil dry matter) had only a small effect on denitrification velocity in four of the five soils. In a clay soil dependence on nitrate concentration corresponded to a first-order reaction. Available C was no limiting factor. Even at zero temperatures remarkable N amounts (on average 0.2 ppm N per day) were still denitrified. The addition of daily turnover rates in relation to soil temperatures prevailing from December to March revealed potential turnovers in the 0-to-30-cm layer of the soils to average 28 ± 5 ppm N. (author)

  14. Performance of fall and winter crops in a no tillage system in west Paraná State

    Directory of Open Access Journals (Sweden)

    Leandro Paiola Albrecht

    2017-11-01

    Full Text Available The long-term exploitation of natural resources by agricultural activities has resulted in the need for alternative measures to restore degraded soil. The cultivation of cover crops can generate great benefits for agricultural systems, enabling the exploitation of natural resources, including water, light and nutrients, as well as the recovery of degraded soils. This work aimed to assess the coverage rate, fresh mass and dry mass of cover crops from fall and winter as well as the floristic composition of the weeds. The work was conducted in field conditions in soil classified as eutroferric Red Oxisol in the region of the city of Palotina, Paraná State, Brazil, using a random block experimental design with four replications. The treatments consisted of seven cover cultures: wild radish, linseed, triticale, rye, rapeseed, crambe, oats and fallow. The species with the highest coverage rates and fresh mass and dry mass values were wild radish, rapeseed and crambe. In the floristic and phytosociological data, the species with the highest incidence were Amaranthus retroflexus, Commelina benghalensis L., Brachiaria plantaginea and Gnaphalium spicatum.

  15. PRINCIPLES OF THE SUPPLY CHAIN PERFORMANCE MEASUREMENT

    OpenAIRE

    BEATA ŒLUSARCZYK; SEBASTIAN KOT

    2012-01-01

    Measurement of performance in every business management is a crucial activity allowing for effectiveness increase. The lack of suitable performance measurement is especially noticed in complex systems as supply chains. Responsible persons cannot manage effectively without suitable set of measures those are base for comparison to previous data or effects of other supply chain functioning. The analysis shows that it is very hard to find balanced set of supply chain performance measures those sh...

  16. Home advantage in the Winter Paralympic Games 1976-2014.

    Science.gov (United States)

    Wilson, Darryl; Ramchandani, Girish

    2017-01-01

    There is a limited amount of home advantage research concerned with winter sports. There is also a distinct lack of studies that investigate home advantage in the context of para sport events. This paper addresses this gap in the knowledge by examining home advantage in the Winter Paralympic Games. Using a standardised measure of success, we compared the performances of host nations at home with their own performances away from home between 1976 and 2014. Both country level and individual sport level analysis is conducted for this time period. Comparisons are also drawn with the Winter Olympic Games since 1992, the point from which both the Winter Olympic Games and the Winter Paralympic Games have been hosted by the same nations and in the same years. Clear evidence of a home advantage effect in the Winter Paralympic Games was found at country level. When examining individual sports, only alpine skiing and cross country skiing returned a significant home advantage effect. When comparing home advantage in the Winter Paralympic Games with the Winter Olympic Games for the last seven host nations (1992-2014), we found that home advantage was generally more pronounced (although not a statistically significant difference) in the case of the former. The causes of home advantage in the Winter Paralympic Games are unclear and should be investigated further.

  17. Performance Measurement in Global Product Development

    DEFF Research Database (Denmark)

    Taylor, Thomas Paul; Ahmed-Kristensen, Saeema

    2013-01-01

    there is a requirement for the process to be monitored and measured relative to the business strategy of an organisation. It was found that performance measurement is a process that helps achieve sustainable business success, encouraging a learning culture within organisations. To this day, much of the research into how...... performance is measured has focussed on the process of product development. However, exploration of performance measurement related to global product development is relatively unexplored and a need for further research is evident. This paper contributes towards understanding how performance is measured...

  18. Health Plan Performance Measurement within Medicare Subvention.

    Science.gov (United States)

    1998-06-01

    the causes of poor performance (Siren & Laffel, 1996). Although outcomes measures such as nosocomial infection rates, admission rates for select...defined. Traditional outcomes measures include infection rates, morbidity, and mortality. The problem with these traditional measures is... Maternal /Child Care Indicators Nursing Staffing Indicators Outcome Indicators Technical Outcomes Plan Performance Stability of Health Plan

  19. Winter Wonderlands

    Science.gov (United States)

    Coy, Mary

    2011-01-01

    Listening to people complain about the hardships of winter and the dreariness of the nearly constant gray sky prompted the author to help her sixth graders recognize and appreciate the beauty that surrounds them for nearly five months of the year in western New York. The author opines that if students could see things more artistically, the winter…

  20. Spatial Variability Analysis of Within-Field Winter Wheat Nitrogen and Grain Quality Using Canopy Fluorescence Sensor Measurements

    Directory of Open Access Journals (Sweden)

    Xiaoyu Song

    2017-03-01

    Full Text Available Wheat grain protein content (GPC is a key component when evaluating wheat nutrition. It is also important to determine wheat GPC before harvest for agricultural and food process enterprises in order to optimize the wheat grading process. Wheat GPC across a field is spatially variable due to the inherent variability of soil properties and position in the landscape. The objectives of this field study were: (i to assess the spatial and temporal variability of wheat nitrogen (N attributes related to the grain quality of winter wheat production through canopy fluorescence sensor measurements; and (ii to examine the influence of spatial variability of soil N and moisture across different growth stages on the wheat grain quality. A geostatistical approach was used to analyze data collected from 110 georeferenced locations. In particular, Ordinary Kriging Analysis (OKA was used to produce maps of wheat GPC, GPC yield, and wheat canopy fluorescence parameters, including simple florescence ratio and Nitrogen Balance Indices (NBI. Soil Nitrate-Nitrogen (NO3-N content and soil Time Domain Reflectometry (TDR value in the study field were also interpolated through the OKA method. The fluorescence parameter maps, soil NO3-N and soil TDR maps obtained from the OKA output were compared with the wheat GPC and GPC yield maps in order to assess their relationships. The results of this study indicate that the NBI spatial variability map in the late stage of wheat growth can be used to distinguish areas that produce higher GPC.

  1. Measuring Distribution Performance? Benchmarking Warrants Your Attention

    Energy Technology Data Exchange (ETDEWEB)

    Ericson, Sean J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Alvarez, Paul [The Wired Group

    2018-04-13

    Identifying, designing, and measuring performance metrics is critical to securing customer value, but can be a difficult task. This article examines the use of benchmarks based on publicly available performance data to set challenging, yet fair, metrics and targets.

  2. Synthesis of work-zone performance measures.

    Science.gov (United States)

    2013-09-01

    The main objective of this synthesis was to identify and summarize how agencies collect, analyze, and report different work-zone : traffic-performance measures, which include exposure, mobility, and safety measures. The researchers also examined comm...

  3. Measuring the performance of business incubators

    OpenAIRE

    VANDERSTRAETEN, Johanna; MATTHYSSENS, Paul; VAN WITTELOOSTUIJN, Arjen

    2012-01-01

    This paper focuses on incubator performance measurement. First, we report the findings of an extensive literature review. Both existing individual measures and more comprehensive measurement systems are discussed. This literature review shows that most incubator researchers and practitioners only use one or a few indicators for performance evaluation, and that existing measurement systems do not recognize the importance of short, medium and long-term results, do not always include an incubato...

  4. The service of public services performance measurement

    DEFF Research Database (Denmark)

    Lystbæk, Christian Tang

    2014-01-01

    that performance measurement serves as “rituals of verification” which promotes the interests of political masters and their mistresses rather than public service. Another area of concern is the cost of performance measurement. Hood & Peters (2004:278) note that performance measurement is likely to “distract...... measurement suggests a range of contested and contradictory propositions. Its alleged benefits include public assurance, better functioning of supply markets for public services, and direct improvements of public services. But the literature also demonstrates the existence of significant concern about...... the actual impact, the costs and unintended consequences associated with performance measurement. This paper identifies the main rationales and rationalities in the scholarly discourse on public services performance measurement. It concludes with some suggestions on how to deal with the many rationales...

  5. COMPANY PERFORMANCE MEASUREMENT AND REPORTING METHODS

    Directory of Open Access Journals (Sweden)

    Nicu Ioana Elena

    2012-12-01

    Full Text Available One of the priorities of economic research has been and remains the re-evaluation of the notion of performance and especially exploring and finding some indicators that would reflect as accurately as possible the subtleties of the economic entity. The main purpose of this paper is to highlight the main company performance measurement and reporting methods. Performance is a concept that raises many question marks concerning the most accurate or the best method of reporting the performance at the company level. The research methodology has aimed at studying the Romanian and foreign specialized literature dealing with the analyzed field, studying magazines specialized on company performance measurement. If the financial performance measurement indicators are considered to offer an accurate image of the situation of the company, the modern approach through non-financial indicators offers a new perspective upon performance measurement, which is based on simplicity. In conclusion, after the theoretical study, I have noticed that the methods of performance measurement, reporting and interpretation are various, the opinions regarding the best performance measurement methods are contradictive and the companies prefer resorting to financial indicators that still play a more important role in the consolidation of the company performance measurement than the non-financial indicators do.

  6. Mobile measurements of particle composition in the Rhine Valley and Zurich. Winter 2007/2008; Mobile Messungen der Partikelzusammensetzung im Rheintal und in der Stadt Zuerich. Winter 2007/2008

    Energy Technology Data Exchange (ETDEWEB)

    Mohr, C.; Weimer, S.; Good, C.; Richter, R.; Prevot, A.; Baltensperger, U.

    2009-07-15

    This report issued by the General Energy Research Department and its Laboratory of Atmospheric Chemistry at the Paul Scherrer Institute (PSI) reports on the results obtained from the measurement of fine-dust quantities and composition in the cantons of eastern Switzerland and the upper Rhine valley during the winter. The PSI analysed the samples on behalf of the Swiss cantons, Vorarlberg (Austria) and the Principality of Liechtenstein. The mobile equipment used and the measurements made in the Rhine Valley between Lake Constance and Chur as well as in the City of Zurich are presented and discussed. The results of the measurements are presented in graphical form and the chemical composition of the pollutants at the different locations are discussed. Details of the instruments used and the routes taken are noted in an appendix.

  7. A Critique of Health System Performance Measurement.

    Science.gov (United States)

    Lynch, Thomas

    2015-01-01

    Health system performance measurement is a ubiquitous phenomenon. Many authors have identified multiple methodological and substantive problems with performance measurement practices. Despite the validity of these criticisms and their cross-national character, the practice of health system performance measurement persists. Theodore Marmor suggests that performance measurement invokes an "incantatory response" wrapped within "linguistic muddle." In this article, I expand upon Marmor's insights using Pierre Bourdieu's theoretical framework to suggest that, far from an aberration, the "linguistic muddle" identified by Marmor is an indicator of a broad struggle about the representation and classification of public health services as a public good. I present a case study of performance measurement from Alberta, Canada, examining how this representational struggle occurs and what the stakes are. © The Author(s) 2015.

  8. Volatile organic compounds in the western Mediterranean basin: urban and rural winter measurements during the DAURE campaign

    Directory of Open Access Journals (Sweden)

    R. Seco

    2013-04-01

    Full Text Available Atmospheric volatile organic compounds (VOCs have key environmental and biological roles, but little is known about the daily VOC mixing ratios in Mediterranean urban and natural environments. We measured VOC mixing ratios concurrently at an urban and a rural site during the winter DAURE campaign in the northeastern Iberian Peninsula, by means of PTR-MS at both locations: a PTR-Quad-MS at the urban site and a PTR-ToF-MS at the rural site. All VOC mixing ratios measured were higher at the urban site (e.g. acetaldehyde, isoprene, benzene, and toluene with averages up to 1.68, 0.31, 0.58 and 2.71 ppbv, respectively, with the exception of some short-chain oxygenated VOCs such as acetone (with similar averages of 0.7–1.6 ppbv at both sites. The average diurnal pattern also differed between the sites. Most of the VOCs at the urban location showed their highest mixing ratios in the morning and evening. These peaks coincided with traffic during rush hour, the main origin of most of the VOCs analyzed. Between these two peaks, the sea breeze transported the urban air inland, thus helping to lower the VOC loading at the urban site. At the rural site, most of the measured VOCs were advected by the midday sea breeze, yielding the highest daily VOC mixing ratios (e.g. acetaldehyde, isoprene, benzene, and toluene with averages up to 0.65, 0.07, 0.19, and 0.41 ppbv, respectively. Only biogenic monoterpenes showed a clear local origin at this site. In addition, the concentrations of fine particulate matter observed at both sites, together with the synoptic meteorological conditions and radio-sounding data, allowed the identification of different atmospheric scenarios that had a clear influence on the measured VOC mixing ratios. These results highlight the differences and relationships in VOC mixing ratios between nearby urban and rural areas in Mediterranean regions. Further research in other urban-rural areas is warranted to better understand the urban

  9. Does hospital financial performance measure up?

    Science.gov (United States)

    Cleverley, W O; Harvey, R K

    1992-05-01

    Comparisons are continuously being made between the financial performance, products and services, of the healthcare industry and those of non-healthcare industries. Several useful measures of financial performance--profitability, liquidity, financial risk, asset management and replacement, and debt capacity, are used by the authors to compare the financial performance of the hospital industry with that of the industrial, transportation and utility sectors. Hospitals exhibit weaknesses in several areas. Goals are suggested for each measure to bring hospitals closer to competitive levels.

  10. On music performance, theories, measurement en diversity

    NARCIS (Netherlands)

    Timmers, R.; Honing, H.J.

    2002-01-01

    Measurement of musical performances is of interest to studies in musicology, music psychology and music performance practice, but in general it has not been considered the main issue: when analyzing Western classical music, these disciplines usually focus on the score rather than the performance.

  11. Development of a Behavioral Performance Measure

    Directory of Open Access Journals (Sweden)

    Marcelo Cabus Klotzle

    2012-09-01

    Full Text Available Since the fifties, several measures have been developed in order to measure the performance of investments or choices involving uncertain outcomes. Much of these measures are based on Expected Utility Theory, but since the nineties a number of measures have been proposed based on Non-Expected Utility Theory. Among the Theories of Non-Expected Utility highlights Prospect Theory, which is the foundation of Behavioral Finance. Based on this theory this study proposes a new performance measure in which are embedded loss aversion along with the likelihood of distortions in the choice of alternatives. A hypothetical example is presented in which various performance measures, including the new measure are compared. The results showed that the ordering of the assets varied depending on the performance measure adopted. According to what was expected, the new performance measure clearly has captured the distortion of probabilities and loss aversion of the decision maker, ie, those assets with the greatest negative deviations from the target were those who had the worst performance.

  12. Melanopsin-Mediated Acute Light Responses Measured in Winter and in Summer: Seasonal Variations in Adults with and without Cataracts

    Directory of Open Access Journals (Sweden)

    Mirjam Münch

    2017-09-01

    Full Text Available Seasonal adaptation is a ubiquitous behavior seen in many species on both global hemispheres and is conveyed by changing photoperiods. In humans this seasonal adaptation is less apparent, in part because changes in daylength are masked by the use of electrical lighting at night. On the other hand, cataracts which reduce light transmission, may compound seasonal changes related to the reduced daylength of winter. To better understand the effects of different photoperiod lengths in healthy adults without and with cataracts, we tested their melanopsin-mediated light responses in summer vs. winter. Fifty-two participants (mean age 67.4 years; 30 with bilateral cataracts and 22 age-matched controls with clear lenses; pseudophakes were tested twice, once in summer and once in winter. At each test session we assessed the electroretinogram and pupil responses during daytime and we determined melatonin suppression, subjective sleepiness and mood in response to light exposure in the evening. Circadian rest-activity cycles and sleep from activity recordings were also analyzed for both seasons. Both groups had similar visual function. There were no seasonal differences in the electroretinogram. For the pupil responses to bright blue light, the post-illumination pupil response (PIPR was greater in winter than summer in pseudophakes, but not in cataract participants, whereas melatonin suppression to acute light exposure showed no differences between both groups and seasons. Overall, intra-daily variability of rest-activity was worse in winter but participants felt sleepier and reported worse mood at the laboratory in evening time in the summer. Those with cataracts had poorer sleep quality with lower sleep efficiency, and higher activity during sleep in winter than summer. In this study, the PIPR showed a seasonal variation in which a larger response was found during winter. This variation was only detected in participants with a clear intraocular lens. In

  13. Performance measures for a dialysis setting.

    Science.gov (United States)

    Gu, Xiuzhu; Itoh, Kenji

    2018-03-01

    This study from Japan extracted performance measures for dialysis unit management and investigated their characteristics from professional views. Two surveys were conducted using self-administered questionnaires, in which dialysis managers/staff were asked to rate the usefulness of 44 performance indicators. A total of 255 managers and 2,097 staff responded. Eight performance measures were elicited from dialysis manager and staff responses: these were safety, operational efficiency, quality of working life, financial effectiveness, employee development, mortality, patient/employee satisfaction and patient-centred health care. These performance measures were almost compatible with those extracted in overall healthcare settings in a previous study. Internal reliability, content and construct validity of the performance measures for the dialysis setting were ensured to some extent. As a general trend, both dialysis managers and staff perceived performance measures as highly useful, especially for safety, mortality, operational efficiency and patient/employee satisfaction, but showed relatively low concerns for patient-centred health care and employee development. However, dialysis managers' usefulness perceptions were significantly higher than staff. Important guidelines for designing a holistic hospital/clinic management system were yielded. Performance measures must be balanced for outcomes and performance shaping factors (PSF); a common set of performance measures could be applied to all the healthcare settings, although performance indicators of each measure should be composed based on the application field and setting; in addition, sound causal relationships between PSF and outcome measures/indicators should be explored for further improvement. © 2017 European Dialysis and Transplant Nurses Association/European Renal Care Association.

  14. MEASUREMENT: ACCOUNTING FOR RELIABILITY IN PERFORMANCE ESTIMATES.

    Science.gov (United States)

    Waterman, Brian; Sutter, Robert; Burroughs, Thomas; Dunagan, W Claiborne

    2014-01-01

    When evaluating physician performance measures, physician leaders are faced with the quandary of determining whether departures from expected physician performance measurements represent a true signal or random error. This uncertainty impedes the physician leader's ability and confidence to take appropriate performance improvement actions based on physician performance measurements. Incorporating reliability adjustment into physician performance measurement is a valuable way of reducing the impact of random error in the measurements, such as those caused by small sample sizes. Consequently, the physician executive has more confidence that the results represent true performance and is positioned to make better physician performance improvement decisions. Applying reliability adjustment to physician-level performance data is relatively new. As others have noted previously, it's important to keep in mind that reliability adjustment adds significant complexity to the production, interpretation and utilization of results. Furthermore, the methods explored in this case study only scratch the surface of the range of available Bayesian methods that can be used for reliability adjustment; further study is needed to test and compare these methods in practice and to examine important extensions for handling specialty-specific concerns (e.g., average case volumes, which have been shown to be important in cardiac surgery outcomes). Moreover, it's important to note that the provider group average as a basis for shrinkage is one of several possible choices that could be employed in practice and deserves further exploration in future research. With these caveats, our results demonstrate that incorporating reliability adjustment into physician performance measurements is feasible and can notably reduce the incidence of "real" signals relative to what one would expect to see using more traditional approaches. A physician leader who is interested in catalyzing performance improvement

  15. Towards integrating environmental performance in divisional performance measurement

    Directory of Open Access Journals (Sweden)

    Collins C Ngwakwe

    2014-08-01

    Full Text Available This paper suggests an integration of environmental performance measurement (EPM into conventional divisional financial performance measures as a catalyst to enhance managers’ drive toward cleaner production and sustainable development. The approach is conceptual and normative; and using a hypothetical firm, it suggests a model to integrate environmental performance measure as an ancillary to conventional divisional financial performance measures. Vroom’s motivation theory and other literature evidence indicate that corporate goals are achievable in an environment where managers’ efforts are recognised and thus rewarded. Consequently the paper suggests that environmentally motivated managers are important to propel corporate sustainability strategy toward desired corporate environmental governance and sustainable economic development. Thus this suggested approach modestly adds to existing environmental management accounting (EMA theory and literature. It is hoped that this paper may provide an agenda for further research toward a practical application of the suggested method in a firm.

  16. Introduction to control system performance measurements

    CERN Document Server

    Garner, K C

    1968-01-01

    Introduction to Control System Performance Measurements presents the methods of dynamic measurements, specifically as they apply to control system and component testing. This book provides an introduction to the concepts of statistical measurement methods.Organized into nine chapters, this book begins with an overview of the applications of automatic control systems that pervade almost every area of activity ranging from servomechanisms to electrical power distribution networks. This text then discusses the common measurement transducer functions. Other chapters consider the basic wave

  17. Internal Performance Measurement Systems: Problems and Solutions

    DEFF Research Database (Denmark)

    Jakobsen, Morten; Mitchell, Falconer; Nørreklit, Hanne

    2010-01-01

    This article pursues two aims: to identify problems and dangers related to the operational use of internal performance measurement systems of the Balanced Scorecard (BSC) type and to provide some guidance on how performance measurement systems may be designed to overcome these problems....... The analysis uses and extends N rreklit's (2000) critique of the BSC by applying the concepts developed therein to contemporary research on the BSC and to the development of practice in performance measurement. The analysis is of relevance for many companies in the Asia-Pacific area as an increasing numbers...

  18. Measurement uncertainty analysis techniques applied to PV performance measurements

    International Nuclear Information System (INIS)

    Wells, C.

    1992-10-01

    The purpose of this presentation is to provide a brief introduction to measurement uncertainty analysis, outline how it is done, and illustrate uncertainty analysis with examples drawn from the PV field, with particular emphasis toward its use in PV performance measurements. The uncertainty information we know and state concerning a PV performance measurement or a module test result determines, to a significant extent, the value and quality of that result. What is measurement uncertainty analysis? It is an outgrowth of what has commonly been called error analysis. But uncertainty analysis, a more recent development, gives greater insight into measurement processes and tests, experiments, or calibration results. Uncertainty analysis gives us an estimate of the I interval about a measured value or an experiment's final result within which we believe the true value of that quantity will lie. Why should we take the time to perform an uncertainty analysis? A rigorous measurement uncertainty analysis: Increases the credibility and value of research results; allows comparisons of results from different labs; helps improve experiment design and identifies where changes are needed to achieve stated objectives (through use of the pre-test analysis); plays a significant role in validating measurements and experimental results, and in demonstrating (through the post-test analysis) that valid data have been acquired; reduces the risk of making erroneous decisions; demonstrates quality assurance and quality control measures have been accomplished; define Valid Data as data having known and documented paths of: Origin, including theory; measurements; traceability to measurement standards; computations; uncertainty analysis of results

  19. Telerobotic system performance measurement - Motivation and methods

    Science.gov (United States)

    Kondraske, George V.; Khoury, George J.

    1992-01-01

    A systems performance-based strategy for modeling and conducting experiments relevant to the design and performance characterization of telerobotic systems is described. A developmental testbed consisting of a distributed telerobotics network and initial efforts to implement the strategy described is presented. Consideration is given to the general systems performance theory (GSPT) to tackle human performance problems as a basis for: measurement of overall telerobotic system (TRS) performance; task decomposition; development of a generic TRS model; and the characterization of performance of subsystems comprising the generic model. GSPT employs a resource construct to model performance and resource economic principles to govern the interface of systems to tasks. It provides a comprehensive modeling/measurement strategy applicable to complex systems including both human and artificial components. Application is presented within the framework of a distributed telerobotics network as a testbed. Insight into the design of test protocols which elicit application-independent data is described.

  20. Performance measurement in transport sector analysis

    Directory of Open Access Journals (Sweden)

    M. Išoraitė

    2004-06-01

    Full Text Available The article analyses the following issues: 1. Performance measurement in literature. The performance measurement has an important role to play in the efficient and effective management of organizations. Kaplan and Johnson highlighted the failure of the financial measures to reflect changes in the competitive circumstances and strategies of modern organizations. Many authors have focused attention on how organizations can design more appropriate measurement systems. Based on literature, consultancy experience and action research, numerous processes have been developed that organizations can follow in order to design and implement systems. Many frameworks have been proposed that support these processes. The objective of such frameworks is to help organizations define a set of measures that reflect their objectives and assess their performance appropriately. 2. Transport sector performance and its impacts measuring. The purpose of transport measurement is to identify opportunities enhancing transport performance. Successful transport sector management requires a system to analyze its efficiency and effectiveness as well as plan interventions if transport sector performance needs improvement. Transport impacts must be measurable and monitorable so that the person responsible for the project intervention can decide when and how to influence them. Performance indicators provide a means to measure and monitor impacts. These indicators essentially reflect quantitative and qualitative aspects of impacts at given time and places. 3. Transport sector output and input. Transport sector inputs are the resources required to deliver transport sector outputs. Transport sector inputs are typically: human resources, particularly skilled resources (including specialists consulting inputs; technology processes such as equipment and work; and finance, both public and private. 4. Transport sector policy and institutional framework; 5. Cause – effect linkages; 6

  1. Payment mechanisms for winter road maintenance services

    Directory of Open Access Journals (Sweden)

    Adel Abdi

    2013-12-01

    Full Text Available In countries with severe winters a major part of the annual budget for road maintenance is allocated on performance of winter road maintenance tasks. Finding appropriate remuneration forms to compensate entrepreneurs for performed road measures during winter is not an easy task in order to minimise or eliminate disputes and satisfy both client organisations and contractors. On the other hand improper reimbursement models lead either to the client’s annual budget imbalance due to unnecessary cost overruns or affect contractor’s cash-flow. Such cases in turn affect just-in-time winter road maintenance and then traffic safety. To solve such problems, a number of countries in cold regions like Sweden have developed different remuneration models based more on weather data called Weather Index. Therefore the objective of this paper is to investigate and evaluate the payment models applied in Sweden. The study uses a number of approaches namely; domestic questionnaire survey, analysis of a number of contract documents, a series of meetings with the project managers and an international benchmarking. The study recognised four remuneration models for winter maintenance service of which one based on weather data statistics. The study reveals the payment model based on weather data statistics is only applied for the roads with higher traffic flow and the model generates most uncertainty.

  2. Measurements of 161 Double Stars With a High-Speed CCD: The Winter/Spring 2017 Observing Program at Brilliant Sky Observatory, Part 2

    Science.gov (United States)

    Harshaw, Richard

    2018-04-01

    In the winter and spring of 2017, an aggressive observing program of measuring close double stars with speckle interferometry and CCD imaging was undertaken at Brilliant Sky Observatory, my observing site in Cave Creek, Arizona. A total of 596 stars were observed, 8 of which were rejected for various reasons, leaving 588 pairs. Of these, 427 were observed and measured with speckle interferometry, while the remaining 161 were measured with a CCD. This paper reports the results of the observations of the 161 CCD cases. A separate paper in this issue will report the speckle measurements of the 427 other pairs.

  3. Measurements of 427 Double Stars With Speckle Interferometry: The Winter/Spring 2017 Observing Program at Brilliant Sky Observatory, Part 1

    Science.gov (United States)

    Harshaw, Richard

    2018-04-01

    In the winter and spring of 2017, an aggressive observing program of measuring close double stars with speckle interferometry and CCD imaging was undertaken at Brilliant Sky Observatory, my observing site in Cave Creek, Arizona. A total of 596 stars were observed, 8 of which were rejected for various reasons, leaving 588 pairs. Of these, 427 were observed and measured with speckle interferometry, while the remaining 161 were measured with a CCD. This paper reports the results of the observations of the 427 speckle cases. A separate paper in this issue will report the CCD measurements of the 161 other pairs.

  4. Vegetative, productive and qualitative performance of grapevine "Cabernet Sauvignon" according to the use of winter cover crops

    Directory of Open Access Journals (Sweden)

    Jean Carlos Bettoni

    Full Text Available ABSTRACT To study the effect of winter cover crops on the vegetative, productive and qualitative behavior of "Cabernet Sauvignon" grapevines, an experiment was conducted in two wine harvests by sowing different species of winter cover crops and additional treatments with manual weeding and mechanical mowing in an experimental vineyard located at the Experimental Station of Epagri in Videira, state of Santa Catarina, Brazil. Plant attributes of the grapevine, such as number of rods and weight of pruned material and number of branches per plant. At the time of skin color change, petioles of recently matured leaves were collected for analysis of the levels of N, P, K, Ca, Mg, Fe, Mn, Zn and B. Moments before harvest, 100 grape berries were collected randomly to determine the total soluble solids, titratable acidity and pH. At harvest, the number of bunches per branch, the number and mass of clusters per plant and the average mass of clusters per plot were determined. Fresh and dry matter yields of the cover crop and weed plants were also determined when coverage reached full bloom. The winter cover crops did not alter the yield and quality of "Cabernet Sauvignon" grapes and showed no differences from each other for the management of spontaneous vegetation by hand weeding or mechanical mowing. Rye and ryegrass are effective alternatives for weed control alternatives. The species of white and red clover present difficulty in initial establishment, producing a small amount of biomass.

  5. Road weather management performance measures : 2012 update.

    Science.gov (United States)

    2013-08-01

    In 2007, the Road Weather Management Program (RWMP) conducted a study with stakeholders from the transportation and meteorological communities to define eleven performance measures that would enable the Federal Highway Administration (FHWA) to determ...

  6. Performance measures for metropolitan planning organizations.

    Science.gov (United States)

    2012-04-01

    Performance measurement is a topic of increasing importance to transportation agencies, as issues with : funding shortfalls and concerns about transportation system efficiency lead to a shift in how transportation : decision making is carried out. In...

  7. Smart city performance measurement framework. CITYkeys

    NARCIS (Netherlands)

    Airaksinen, M.; Seppa, I.P.; Huovilla, A.; Neumann, H.M.; Iglar, B.; Bosch, P.R.

    2017-01-01

    This paper presents a holistic performance measurement framework for harmonized and transparent monitoring and comparability of the European cities activities during the implementation of Smart City solutions. The work methodology was based on extensive collaboration and communication with European

  8. Geochemistry of PM10 over Europe during the EMEP intensive measurement periods in summer 2012 and winter 2013

    Directory of Open Access Journals (Sweden)

    A. Alastuey

    2016-05-01

    Full Text Available The third intensive measurement period (IMP organised by the European Monitoring and Evaluation Programme (EMEP under the UNECE CLTRAP took place in summer 2012 and winter 2013, with PM10 filter samples concurrently collected at 20 (16 EMEP regional background sites across Europe for subsequent analysis of their mineral dust content. All samples were analysed by the same or a comparable methodology. Higher PM10 mineral dust loadings were observed at most sites in summer (0.5–10 µg m−3 compared to winter (0.2–2 µg m−3, with the most elevated concentrations in the southern- and easternmost countries, accounting for 20–40 % of PM10. Saharan dust outbreaks were responsible for the high summer dust loadings at western and central European sites, whereas regional or local sources explained the elevated concentrations observed at eastern sites. The eastern Mediterranean sites experienced elevated levels due to African dust outbreaks during both summer and winter. The mineral dust composition varied more in winter than in summer, with a higher relative contribution of anthropogenic dust during the former period. A relatively high contribution of K from non-mineral and non-sea-salt sources, such as biomass burning, was evident in winter at some of the central and eastern European sites. The spatial distribution of some components and metals reveals the influence of specific anthropogenic sources on a regional scale: shipping emissions (V, Ni, and SO42− in the Mediterranean region, metallurgy (Cr, Ni, and Mn in central and eastern Europe, high temperature processes (As, Pb, and SO42− in eastern countries, and traffic (Cu at sites affected by emissions from nearby cities.

  9. Work zone performance measures pilot test.

    Science.gov (United States)

    2011-04-01

    Currently, a well-defined and validated set of metrics to use in monitoring work zone performance do not : exist. This pilot test was conducted to assist state DOTs in identifying what work zone performance : measures can and should be targeted, what...

  10. ASUPT Automated Objective Performance Measurement System.

    Science.gov (United States)

    Waag, Wayne L.; And Others

    To realize its full research potential, a need exists for the development of an automated objective pilot performance evaluation system for use in the Advanced Simulation in Undergraduate Pilot Training (ASUPT) facility. The present report documents the approach taken for the development of performance measures and also presents data collected…

  11. Environmental Measurements Laboratory 2002 Unit Performance Plan

    Energy Technology Data Exchange (ETDEWEB)

    None

    2001-10-01

    This EML Unit Performance Plan provides the key goals and performance measures for FY 2002 and continuing to FY 2003. The purpose of the Plan is to inform EML's stakeholders and customers of the Laboratory's products and services, and its accomplishments and future challenges. Also incorporated in the Unit Performance Plan is EML's Communication Plan for FY 2002.

  12. Measuring performance in virtual reality phacoemulsification surgery

    Science.gov (United States)

    Söderberg, Per; Laurell, Carl-Gustaf; Simawi, Wamidh; Skarman, Eva; Nordh, Leif; Nordqvist, Per

    2008-02-01

    We have developed a virtual reality (VR) simulator for phacoemulsification surgery. The current work aimed at developing a relative performance index that characterizes the performance of an individual trainee. We recorded measurements of 28 response variables during three iterated surgical sessions in 9 experienced cataract surgeons, separately for the sculpting phase and the evacuation phase of phacoemulsification surgery and compared their outcome to that of a reference group of naive trainees. We defined an individual overall performance index, an individual class specific performance index and an individual variable specific performance index. We found that on an average the experienced surgeons performed at a lower level than a reference group of naive trainees but that this was particularly attributed to a few surgeons. When their overall performance index was further analyzed as class specific performance index and variable specific performance index it was found that the low level performance was attributed to a behavior that is acceptable for an experienced surgeon but not for a naive trainee. It was concluded that relative performance indices should use a reference group that corresponds to the measured individual since the definition of optimal surgery may vary among trainee groups depending on their level of experience.

  13. APPROXIMATIONS TO PERFORMANCE MEASURES IN QUEUING SYSTEMS

    Directory of Open Access Journals (Sweden)

    Kambo, N. S.

    2012-11-01

    Full Text Available Approximations to various performance measures in queuing systems have received considerable attention because these measures have wide applicability. In this paper we propose two methods to approximate the queuing characteristics of a GI/M/1 system. The first method is non-parametric in nature, using only the first three moments of the arrival distribution. The second method treads the known path of approximating the arrival distribution by a mixture of two exponential distributions by matching the first three moments. Numerical examples and optimal analysis of performance measures of GI/M/1 queues are provided to illustrate the efficacy of the methods, and are compared with benchmark approximations.

  14. Reconsidering the measurement of ancillary service performance.

    Science.gov (United States)

    Griffin, D T; Rauscher, J A

    1987-08-01

    Prospective payment reimbursement systems have forced hospitals to review their costs more carefully. The result of the increased emphasis on costs is that many hospitals use costs, rather than margin, to judge the performance of ancillary services. However, arbitrary selection of performance measures for ancillary services can result in managerial decisions contrary to hospital objectives. Managerial accounting systems provide models which assist in the development of performance measures for ancillary services. Selection of appropriate performance measures provides managers with the incentive to pursue goals congruent with those of the hospital overall. This article reviews the design and implementation of managerial accounting systems, and considers the impact of prospective payment systems and proposed changes in capital reimbursement on this process.

  15. Measurement Of Shariah Stock Performance Using Risk Adjusted Performance

    Directory of Open Access Journals (Sweden)

    Zuhairan Y Yunan

    2015-03-01

    Full Text Available The aim of this research is to analyze the shariah stock performance using risk adjusted performance method. There are three parameters to measure the stock performance i.e. Sharpe, Treynor, and Jensen. This performance’s measurements calculate the return and risk factor from shariah stocks. The data that used on this research is using the data of stocks at Jakarta Islamic Index. Sampling method that used on this paper is purposive sampling. This research is using ten companies as a sample. The result shows that from three parameters, the stock that have a best performance are AALI, ANTM, ASII, CPIN, INDF, KLBF, LSIP, and UNTR.DOI: 10.15408/aiq.v7i1.1364

  16. Developing Human Performance Measures (PSAM8)

    International Nuclear Information System (INIS)

    Jeffrey C. Joe

    2006-01-01

    Through the reactor oversight process (ROP), the U.S. Nuclear Regulatory Commission (NRC) monitors the performance of utilities licensed to operate nuclear power plants. The process is designed to assure public health and safety by providing reasonable assurance that licensees are meeting the cornerstones of safety and designated crosscutting elements. The reactor inspection program, together with performance indicators (PIs), and enforcement activities form the basis for the NRC's risk-informed, performance based regulatory framework. While human performance is a key component in the safe operation of nuclear power plants and is a designated cross-cutting element of the ROP, there is currently no direct inspection or performance indicator for assessing human performance. Rather, when human performance is identified as a substantive cross cutting element in any 1 of 3 categories (resources, organizational or personnel), it is then evaluated for common themes to determine if follow-up actions are warranted. However, variability in human performance occurs from day to day, across activities that vary in complexity, and workgroups, contributing to the uncertainty in the outcomes of performance. While some variability in human performance may be random, much of the variability may be attributed to factors that are not currently assessed. There is a need to identify and assess aspects of human performance that relate to plant safety and to develop measures that can be used to successfully assure licensee performance and indicate when additional investigation may be required. This paper presents research that establishes a technical basis for developing human performance measures. In particular, we discuss: (1) how historical data already gives some indication of connection between human performance and overall plant performance, (2) how industry led efforts to measure and model human performance and organizational factors could serve as a data source and basis for a

  17. Winter frost resistance of Pinus cembra measured in situ at the alpine timberline as affected by temperature conditions.

    Science.gov (United States)

    Buchner, Othmar; Neuner, Gilbert

    2011-11-01

    Winter frost resistance (WFR), midwinter frost hardening and frost dehardening potential of Pinus cembra L. were determined in situ by means of a novel low-temperature freezing system at the alpine timberline ecotone (1950 m a.s.l., Mt Patscherkofel, Innsbruck, Austria). In situ liquid nitrogen (LN₂)-quenching experiments should check whether maximum WFR of P. cembra belonging to the frost hardiest conifer group, being classified in US Department of Agriculture climatic zone 1, suffices to survive dipping into LN₂ (-196 °C). Viability was assessed in a field re-growth test. Maximum in situ WFR (LT₅₀) of leaves was frost hardening treatment (12 days at -20 °C followed by 3 days at -50 °C) to induce maximum WFR. Temperature treatments applied in the field significantly affected the actual WFR. In January a frost hardening treatment (21 days at -20 °C) led to a significant increase of WFR (buds: -62 °C to frost dehardening (buds: -32.6 °C to -10.2 °C; leaves: -32.7 to -16.4 °C) followed by significantly earlier bud swelling and burst in late winter. Strikingly, both temperature treatments, either increased air temperature (+10.1 °C) or increased soil temperature (+6.5 °C), were similarly effective. This high readiness to frost harden and deharden in winter in the field must be considered to be of great significance for future winter survival of P. cembra. Determination of WFR in field re-growth tests appears to be a valuable tool for critically judging estimates of WFR obtained on detached twigs in an ecological context.

  18. Evaluation of the energy and comfort performance of a plus-energy house under Scandinavian winter conditions

    DEFF Research Database (Denmark)

    Pean, Thibault Quentin; Gennari, Luca; Kazanci, Ongun Berk

    evaluation, these results show an encouraging trend towards achieving an annual positive energy balance as designed for this plus-energy house. The thermal environmental conditions in the semi-outdoor space resulted more comfortable than the outdoors, with reduced wind velocity, protection from rain......A plus-energy house was studied in terms of indoor environmental conditions and energy balance, during Scandinavian winter conditions. The studied building, EMBRACE, is a single-family detached dwelling of 59 m2 with two floors. The house also integrates a semi-outdoor space, covered by a glazed...

  19. Measurement uncertainty analysis techniques applied to PV performance measurements

    Energy Technology Data Exchange (ETDEWEB)

    Wells, C.

    1992-10-01

    The purpose of this presentation is to provide a brief introduction to measurement uncertainty analysis, outline how it is done, and illustrate uncertainty analysis with examples drawn from the PV field, with particular emphasis toward its use in PV performance measurements. The uncertainty information we know and state concerning a PV performance measurement or a module test result determines, to a significant extent, the value and quality of that result. What is measurement uncertainty analysis It is an outgrowth of what has commonly been called error analysis. But uncertainty analysis, a more recent development, gives greater insight into measurement processes and tests, experiments, or calibration results. Uncertainty analysis gives us an estimate of the I interval about a measured value or an experiment's final result within which we believe the true value of that quantity will lie. Why should we take the time to perform an uncertainty analysis A rigorous measurement uncertainty analysis: Increases the credibility and value of research results; allows comparisons of results from different labs; helps improve experiment design and identifies where changes are needed to achieve stated objectives (through use of the pre-test analysis); plays a significant role in validating measurements and experimental results, and in demonstrating (through the post-test analysis) that valid data have been acquired; reduces the risk of making erroneous decisions; demonstrates quality assurance and quality control measures have been accomplished; define Valid Data as data having known and documented paths of: Origin, including theory; measurements; traceability to measurement standards; computations; uncertainty analysis of results.

  20. Measurement uncertainty analysis techniques applied to PV performance measurements

    Energy Technology Data Exchange (ETDEWEB)

    Wells, C

    1992-10-01

    The purpose of this presentation is to provide a brief introduction to measurement uncertainty analysis, outline how it is done, and illustrate uncertainty analysis with examples drawn from the PV field, with particular emphasis toward its use in PV performance measurements. The uncertainty information we know and state concerning a PV performance measurement or a module test result determines, to a significant extent, the value and quality of that result. What is measurement uncertainty analysis? It is an outgrowth of what has commonly been called error analysis. But uncertainty analysis, a more recent development, gives greater insight into measurement processes and tests, experiments, or calibration results. Uncertainty analysis gives us an estimate of the I interval about a measured value or an experiment`s final result within which we believe the true value of that quantity will lie. Why should we take the time to perform an uncertainty analysis? A rigorous measurement uncertainty analysis: Increases the credibility and value of research results; allows comparisons of results from different labs; helps improve experiment design and identifies where changes are needed to achieve stated objectives (through use of the pre-test analysis); plays a significant role in validating measurements and experimental results, and in demonstrating (through the post-test analysis) that valid data have been acquired; reduces the risk of making erroneous decisions; demonstrates quality assurance and quality control measures have been accomplished; define Valid Data as data having known and documented paths of: Origin, including theory; measurements; traceability to measurement standards; computations; uncertainty analysis of results.

  1. Ambulatory care registered nurse performance measurement.

    Science.gov (United States)

    Swan, Beth Ann; Haas, Sheila A; Chow, Marilyn

    2010-01-01

    On March 1-2, 2010, a state-of-the-science invitational conference titled "Ambulatory Care Registered Nurse Performance Measurement" was held to focus on measuring quality at the RN provider level in ambulatory care. The conference was devoted to ambulatory care RN performance measurement and quality of health care. The specific emphasis was on formulating a research agenda and developing a strategy to study the testable components of the RN role related to care coordination and care transitions, improving patient outcomes, decreasing health care costs, and promoting sustainable system change. The objectives were achieved through presentations and discussion among expert inter-professional participants from nursing, public health, managed care, research, practice, and policy. Conference speakers identified priority areas for a unified practice, policy, and research agenda. Crucial elements of the strategic dialogue focused on issues and implications for nursing and inter-professional practice, quality, and pay-for-performance.

  2. Procedure to Measure Indoor Lighting Energy Performance

    Energy Technology Data Exchange (ETDEWEB)

    Deru, M.; Blair, N.; Torcellini, P.

    2005-10-01

    This document provides standard definitions of performance metrics and methods to determine them for the energy performance of building interior lighting systems. It can be used for existing buildings and for proposed buildings. The primary users for whom these documents are intended are building energy analysts and technicians who design, install, and operate data acquisition systems, and who analyze and report building energy performance data. Typical results from the use of this procedure are the monthly and annual energy used for lighting, energy savings from occupancy or daylighting controls, and the percent of the total building energy use that is used by the lighting system. The document is not specifically intended for retrofit applications. However, it does complement Measurement and Verification protocols that do not provide detailed performance metrics or measurement procedures.

  3. Performance measures for transform data coding.

    Science.gov (United States)

    Pearl, J.; Andrews, H. C.; Pratt, W. K.

    1972-01-01

    This paper develops performance criteria for evaluating transform data coding schemes under computational constraints. Computational constraints that conform with the proposed basis-restricted model give rise to suboptimal coding efficiency characterized by a rate-distortion relation R(D) similar in form to the theoretical rate-distortion function. Numerical examples of this performance measure are presented for Fourier, Walsh, Haar, and Karhunen-Loeve transforms.

  4. Comparison of Summer and Winter Objectively Measured Physical Activity and Sedentary Behavior in Older Adults: Age, Gene/Environment Susceptibility Reykjavik Study.

    Science.gov (United States)

    Arnardottir, Nanna Yr; Oskarsdottir, Nina Dora; Brychta, Robert J; Koster, Annemarie; van Domelen, Dane R; Caserotti, Paolo; Eiriksdottir, Gudny; Sverrisdottir, Johanna E; Johannsson, Erlingur; Launer, Lenore J; Gudnason, Vilmundur; Harris, Tamara B; Chen, Kong Y; Sveinsson, Thorarinn

    2017-10-21

    In Iceland, there is a large variation in daylight between summer and winter. The aim of the study was to identify how this large variation influences physical activity (PA) and sedentary behavior (SB). Free living PA was measured by a waist-worn accelerometer for one week during waking hours in 138 community-dwelling older adults (61.1% women, 80.3 ± 4.9 years) during summer and winter months. In general, SB occupied about 75% of the registered wear-time and was highly correlated with age (β = 0.36). Although the differences were small, more time was spent during the summer in all PA categories, except for the moderate-to-vigorous PA (MVPA), and SB was reduced. More lifestyle PA (LSPA) was accumulated in ≥5-min bouts during summer than winter, especially among highly active participants. This information could be important for policy makers and health professionals working with older adults. Accounting for seasonal difference is necessary in analyzing SB and PA data.

  5. Air pollution from wood combustion. Measurements at Elverum, Norway during the winters 1981 and 1982. Luftforurensning fra vedfyring. Maalinger i Elverum, Norge vintrene 1981 og 1982

    Energy Technology Data Exchange (ETDEWEB)

    Ramdahl, T; Schjoldager, J; Hanssen, J E; Moeller, M

    1983-01-01

    Ambient sampling and analysis of air pollutants related to wood combustion have been carried out at the town of Elverum, Norway during the winters of 1981 and 1982. Two measurement sites were selected, Elverum (within the town) and Strandfossen. The concentration of fine particles, PAH and benzene on cold days in Elverum was similar to average winter concentrations in central parts of Oslo. The concentrations in Elverum were highest during a cold period in January, second highest during a cold period in February, and lowest during a mild period between the two cold periods. The same variation was found for mutagenicity. The concentration at the site Elverum was considerably higher than at the site Stranfossen. Organic compounds characteristic of wood smoke have been found in the ambient particulate samples, especially on cold days. The concentration of total particulate carbon and carbon from biomass showed similar variations as fine particles and PAH. The average fraction of carbon from biomass relative to the total carbon concentration was 70 percent, and the fraction was highest on cold days. The average fraction corresponded quite well with an emission estimate of PAH giving an average PAH contribution from wood combustion of 60-70 percent in the winter season. The analyses of lead indicated a contribution of 3-6 percent from gasoline cars to the fine particle concentreration.

  6. Comparison of Summer and Winter Objectively Measured Physical Activity and Sedentary Behavior in Older Adults: Age, Gene/Environment Susceptibility Reykjavik Study

    Directory of Open Access Journals (Sweden)

    Nanna Yr Arnardottir

    2017-10-01

    Full Text Available In Iceland, there is a large variation in daylight between summer and winter. The aim of the study was to identify how this large variation influences physical activity (PA and sedentary behavior (SB. Free living PA was measured by a waist-worn accelerometer for one week during waking hours in 138 community-dwelling older adults (61.1% women, 80.3 ± 4.9 years during summer and winter months. In general, SB occupied about 75% of the registered wear-time and was highly correlated with age (β = 0.36. Although the differences were small, more time was spent during the summer in all PA categories, except for the moderate-to-vigorous PA (MVPA, and SB was reduced. More lifestyle PA (LSPA was accumulated in ≥5-min bouts during summer than winter, especially among highly active participants. This information could be important for policy makers and health professionals working with older adults. Accounting for seasonal difference is necessary in analyzing SB and PA data.

  7. Corporate Social Performance: From Output Measurement to Impact Measurement

    NARCIS (Netherlands)

    K.E.H. Maas (Karen)

    2009-01-01

    textabstractAll organisations have social, environmental and economic impacts that effect people, their communities and the natural environment. Impacts include intended as well as unintended effects and negative as well as positive effects. Current practice in performance measurement tends to focus

  8. Application of data mining in performance measures

    Science.gov (United States)

    Chan, Michael F. S.; Chung, Walter W.; Wong, Tai Sun

    2001-10-01

    This paper proposes a structured framework for exploiting data mining application for performance measures. The context is set in an airline company is illustrated for the use of such framework. The framework takes in consideration of how a knowledge worker interacts with performance information at the enterprise level to support them to make informed decision in managing the effectiveness of operations. A case study of applying data mining technology for performance data in an airline company is illustrated. The use of performance measures is specifically applied to assist in the aircraft delay management process. The increasingly dispersed and complex operations of airline operation put much strain on the part of knowledge worker in using search, acquiring and analyzing information to manage performance. One major problem faced with knowledge workers is the identification of root causes of performance deficiency. The large amount of factors involved in the analyze the root causes can be time consuming and the objective of applying data mining technology is to reduce the time and resources needed for such process. The increasing market competition for better performance management in various industries gives rises to need of the intelligent use of data. Because of this, the framework proposed here is very much generalizable to industries such as manufacturing. It could assist knowledge workers who are constantly looking for ways to improve operation effectiveness through new initiatives and the effort is required to be quickly done to gain competitive advantage in the marketplace.

  9. Air pollution from wood combustion. Measurements at Elverum, Norway during the winters 1981 and 1982. Luftforurensning fra vedfyring. Maalinger i Elverum, Norge vintrene 1981 og 1982

    Energy Technology Data Exchange (ETDEWEB)

    Ramdahl, T; Schjoldager, J; Hanssen, J E; Moeller, M

    1983-01-01

    Ambient sampling and anlysis of air pollutants related to wood combustion have been carried out at the town of Elverum, Norway during the winters of 1981 and 1982. Two measurement sites were selected, Elverum (within the town) and Strandfossen. The concentration of fine particles, PAH and benzene on cold days in Elverum was similar to average winter concentrations in central parts of Oslo. The concentrations in Elverum were highest during a cold period in January, second highest during a cold period in February, and lowest during a mild period between the two cold periods. The same variation was found for mutagenicity. The concentration at the site Elverum was considerably higher than at the site Stranfossen. Organic compounds characteristic of wood smoke have been found in the ambient particulate samples, especially on cold days. The concentration of total particulate carbon and carbon from biomass showed similar variations as fine particles and PAH. The average fraction of carbon from biomass relative to the total carbon concentration was 70 percent, and the fraction was highest on cold days. The average fraction corresponded quite well with an emission estimate of PAH giving an average PAH contribution from wood combustion of 60-70 percent in the winter season. The analyses of lead indicated a contribution of 3-6 percent from gasoline cars to the fine particle concentreration, which corresponds well with the emission estimate of PAH, giving an average PAH contribution from automobile traffic of 4-5 percent in the winter season. The study claerly indicates that the combustion of wood contrubutes significantly to the concentration of air pollutants in Elverum on cold days, especially fine particles, PAH and other carbonaceous compounds.

  10. Frequency Control Performance Measurement and Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Illian, Howard F.

    2010-12-20

    Frequency control is an essential requirement of reliable electric power system operations. Determination of frequency control depends on frequency measurement and the practices based on these measurements that dictate acceptable frequency management. This report chronicles the evolution of these measurements and practices. As technology progresses from analog to digital for calculation, communication, and control, the technical basis for frequency control measurement and practices to determine acceptable performance continues to improve. Before the introduction of digital computing, practices were determined largely by prior experience. In anticipation of mandatory reliability rules, practices evolved from a focus primarily on commercial and equity issues to an increased focus on reliability. This evolution is expected to continue and place increased requirements for more precise measurements and a stronger scientific basis for future frequency management practices in support of reliability.

  11. WINTER SAECULUM

    Directory of Open Access Journals (Sweden)

    Emil Mihalina

    2017-03-01

    Full Text Available Accumulated imbalances in the economy and on the markets cause specific financial market dynamics that have formed characteristic patterns kept throughout long financial history. In 2008 Authors presented their expectations of key macroeconomic and selected asset class markets developments for period ahead based on Saeculum theory. Use of term Secular describes a specific valuation environment during prolonged period. If valuations as well as selected macro variables are considered as a tool for understanding business cycles then market cycles become much more obvious and easily understandable. Therefore over the long run, certain asset classes do better in terms of risk reward profile than others. Further on, there is no need for frequent portfolio rebalancing and timing of specific investment positions within a particular asset class market. Current stage in cycle development suggests a need for reassessment of trends and prevailing phenomena due to cyclical nture of long lasting Saeculums. Paper reviews developments in recognizable patterns of selected metrics in current Winter Saeculum dominated with prevailing forces of delivering, deflation and decrease in velocity of money.

  12. CITYkeys Smart city performance measurement system

    NARCIS (Netherlands)

    Huovila, A.; Airaksinen, M.; Pinto-Seppa, I.; Piira, K.; Bosch, P.R.; Penttinen, T.; Neumann, H.M.; Kontinakis, N.

    2017-01-01

    Cities are tackling their economic, social and environmental challenges through smart city solutions. To demonstrate that these solutions achieve the desired impact, an indicator-based assessment system is needed. This paper presents the process of developing CITYkeys performance measurement system

  13. The Validity of Subjective Performance Measures

    DEFF Research Database (Denmark)

    Meier, Kenneth J.; Winter, Søren C.; O'Toole, Laurence J.

    2015-01-01

    to provide, and are highly policy specific rendering generalization difficult. But are perceptual performance measures valid, and do they generate unbiased findings? We examine these questions in a comparative study of middle managers in schools in Texas and Denmark. The findings are remarkably similar...

  14. Performance Measurement in Helicopter Training and Operations.

    Science.gov (United States)

    Prophet, Wallace W.

    For almost 15 years, HumRRO Division No. 6 has conducted an active research program on techniques for measuring the flight performance of helicopter trainees and pilots. This program addressed both the elemental aspects of flying (i.e., maneuvers) and the mission- or goal-oriented aspects. A variety of approaches has been investigated, with the…

  15. Testing for Distortions in Performance Measures

    DEFF Research Database (Denmark)

    Sloof, Randolph; Van Praag, Mirjam

    2015-01-01

    Distorted performance measures in compensation contracts elicit suboptimal behavioral responses that may even prove to be dysfunctional (gaming). This paper applies the empirical test developed by Courty and Marschke (Review of Economics and Statistics, 90, 428-441) to detect whether the widely...

  16. Testing for Distortions in Performance Measures

    DEFF Research Database (Denmark)

    Sloof, Randolph; Van Praag, Mirjam

    Distorted performance measures in compensation contracts elicit suboptimal behavioral responses that may even prove to be dysfunctional (gaming). This paper applies the empirical test developed by Courty and Marschke (2008) to detect whether the widely used class of Residual Income based performa...

  17. Performance measurement in industrial R&D

    NARCIS (Netherlands)

    Kerssens-van Drongelen, I.C.; Nixon, Bill; Pearson, Alan

    2000-01-01

    Currently, the need for R&D performance measurements that are both practically useful and theoretically sound seems to be generally acknowledged; indeed, the rising cost of R&D, greater emphasis on value management and a trend towards decentralization are escalating the need for ways of evaluating

  18. External Innovation Implementation Determinants and Performance Measurement

    DEFF Research Database (Denmark)

    Coates, Matthew; Bals, Lydia

    2013-01-01

    for innovation implementation based on a case study in the pharmaceutical industry. The results of 25 expert interviews and a survey with 67 respondents led to the resulting framework and a corresponding performance measurement system. The results reveal the importance of supporting systems and show differences...

  19. 20 CFR 638.302 - Performance measurement.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Performance measurement. 638.302 Section 638.302 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR JOB CORPS PROGRAM UNDER TITLE IV-B OF THE JOB TRAINING PARTNERSHIP ACT Funding, Site Selection, and Facilities Management...

  20. Tools for Measuring and Improving Performance.

    Science.gov (United States)

    Jurow, Susan

    1993-01-01

    Explains the need for meaningful performance measures in libraries and the Total Quality Management (TQM) approach to data collection. Five tools representing different stages of a TQM inquiry are covered (i.e., the Shewhart Cycle, flowcharts, cause-and-effect diagrams, Pareto charts, and control charts), and benchmarking is addressed. (Contains…

  1. Performance measures for world class maintenance

    International Nuclear Information System (INIS)

    Labib, A.W.

    1998-01-01

    A main problem in maintenance in general, and in power plants and related equipment in particular, is the lack of a practical, consistent, and adaptive performance measure that provides a focused feedback and integrates preventive and corrective modes of maintenance. The presentation defines concepts of world class and benchmarking. Desirable features in an appropriate performance measure are identified. It then, demonstrates current practices in maintenance and criticises their shortcomings. An alternative model is presented through a case study. The model monitors performance from a general view, and then offers a focused analysis. The main conclusion is that the proposed model offers an adaptive and a dynamic framework, and hence production and maintenance are integrated in a 'real time' environment. The system is also flexible in working with any other criteria whether they are of a quantitative or a qualitative nature. (orig.) 16 refs

  2. Performance measures for world class maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Labib, A.W. [Department of Mechanical Engineering, University of Manchester, Institute of Science and Technology, Manchester (United Kingdom)

    1998-12-31

    A main problem in maintenance in general, and in power plants and related equipment in particular, is the lack of a practical, consistent, and adaptive performance measure that provides a focused feedback and integrates preventive and corrective modes of maintenance. The presentation defines concepts of world class and benchmarking. Desirable features in an appropriate performance measure are identified. It then, demonstrates current practices in maintenance and criticises their shortcomings. An alternative model is presented through a case study. The model monitors performance from a general view, and then offers a focused analysis. The main conclusion is that the proposed model offers an adaptive and a dynamic framework, and hence production and maintenance are integrated in a `real time` environment. The system is also flexible in working with any other criteria whether they are of a quantitative or a qualitative nature. (orig.) 16 refs.

  3. Performance measures for world class maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Labib, A W [Department of Mechanical Engineering, University of Manchester, Institute of Science and Technology, Manchester (United Kingdom)

    1999-12-31

    A main problem in maintenance in general, and in power plants and related equipment in particular, is the lack of a practical, consistent, and adaptive performance measure that provides a focused feedback and integrates preventive and corrective modes of maintenance. The presentation defines concepts of world class and benchmarking. Desirable features in an appropriate performance measure are identified. It then, demonstrates current practices in maintenance and criticises their shortcomings. An alternative model is presented through a case study. The model monitors performance from a general view, and then offers a focused analysis. The main conclusion is that the proposed model offers an adaptive and a dynamic framework, and hence production and maintenance are integrated in a `real time` environment. The system is also flexible in working with any other criteria whether they are of a quantitative or a qualitative nature. (orig.) 16 refs.

  4. Sources and atmospheric processing of winter aerosols in Seoul, Korea: insights from real-time measurements using a high-resolution aerosol mass spectrometer

    Science.gov (United States)

    Kim, Hwajin; Zhang, Qi; Bae, Gwi-Nam; Kim, Jin Young; Bok Lee, Seung

    2017-02-01

    Highly time-resolved chemical characterization of nonrefractory submicrometer particulate matter (NR-PM1) was conducted in Seoul, the capital and largest metropolis of Korea, using an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). The measurements were performed during winter, when elevated particulate matter (PM) pollution events are often observed. This is the first time that detailed real-time aerosol measurement results have been reported from Seoul, Korea, and they reveal valuable insights into the sources and atmospheric processes that contribute to PM pollution in this region. The average concentration of submicron aerosol (PM1 = NR-PM1+ black carbon (BC)) was 27.5 µg m-3, and the total mass was dominated by organics (44 %), followed by nitrate (24 %) and sulfate (10 %). The average atomic ratios of oxygen to carbon (O / C), hydrogen to carbon (H / C), and nitrogen to carbon (N / C) of organic aerosols (OA) were 0.37, 1.79, and 0.018, respectively, which result in an average organic mass-to-carbon (OM / OC) ratio of 1.67. The concentrations (2.6-90.7 µg m-3) and composition of PM1 varied dynamically during the measurement period due to the influences of different meteorological conditions, emission sources, and air mass origins. Five distinct sources of OA were identified via positive matrix factorization (PMF) analysis of the HR-ToF-AMS data: vehicle emissions represented by a hydrocarbon-like OA factor (HOA, O / C = 0.06), cooking activities represented by a cooking OA factor (COA, O / C = 0.14), wood combustion represented by a biomass burning OA factor (BBOA, O / C = 0.34), and secondary organic aerosol (SOA) represented by a semivolatile oxygenated OA factor (SV-OOA, O / C = 0.56) and a low-volatility oxygenated OA factor (LV-OOA, O / C = 0.68). On average, primary OA (POA = HOA + COA + BBOA) accounted for 59 % the OA mass, whereas SV-OOA and LV-OOA contributed 15 and 26 %, respectively. Our results indicate that air

  5. Improvement an enterprises marketing performance measurement system

    Directory of Open Access Journals (Sweden)

    Stanković Ljiljana

    2013-01-01

    Full Text Available Business conditions in which modern enterprises do business are more and more complex. The complexity of the business environment is caused by activities of external and internal factors, which imposes the need for the turn in management focus. One of key turns is related to the need of adaptation and development of new business performance evaluation systems. The evaluation of marketing contribution to business performance is very important however a complex task as well. The marketing theory and practice indicates the need for developing adequate standards and systems for evaluating the efficiency of marketing decisions. The better understanding of marketing standards and ways that managers use is a very important factor that affects the efficiency of strategic decision-making. The paper presents the results of researching the way in which managers perceive and apply marketing performance measures. The data that were received through the field research sample enabled the consideration of the managers' attitudes on practical ways of implementing marketing performance measurement and identifying measures that managers imply as used mostly in business practice.

  6. Total performance measurement and management: TPM2

    Energy Technology Data Exchange (ETDEWEB)

    Sheather, G. [University of Technology, Sydney, NSW (Australia)

    1996-10-01

    As the rate of incremental improvement activities and business process re-engineering programs increase, product development times reduce, collaborative endeavours between OEMs and out-sourcing suppliers increase, as agile manufacturing responds to the demands of a global marketplace, the `virtual` organisation is becoming a reality. In this context, customers, partners, suppliers and manufacturers are increasingly separated by field geography, time zone, and availability, but linked by distributed information systems. Measuring and monitoring business performance in this environment requires a entirely different framework and set of key performance indicators (KPIs) usually associated with traditional financial accounting approaches. These approaches are critiqued, then the paper introduces a new concept `Total Performance Measurement Management` (TPM2), to distinguish it from the conventional TPM (Total Productive Management). A model for combining both financial and non-financial KPIs relevant to real-time performance measures stretching across strategic, business unit and operational levels, is presented. The results of the model confirm the hypothesis that it is feasible to develop a TPM2 framework for achieving enterprise wide strategic objectives. (author). 6 tabs., 18 figs., refs.

  7. Performance expectations of measurement control programs

    International Nuclear Information System (INIS)

    Hammond, G.A.

    1985-01-01

    The principal index for designing and assessing the effectiveness of safeguards is the sensitivity and reliability of gauging the true status of material balances involving material flows, transfers, inventories, and process holdup. The measurement system must not only be capable of characterizing the material for gradation or intensity of protection, but also be responsive to needs for detection and localization of losses, provide confirmation that no diversion has occurred, and help meet requirements for process control, health and safety. Consequently, the judicious application of a measurement control and quality assurance program is vital to a complete understanding of the capabilities and limitations of the measurement system including systematic and random components of error for weight, volume, sampling, chemical, isotopic, and nondestructive determinations of material quantities in each material balance area. This paper describes performance expectations or criteria for a measurement control program in terms of ''what'' is desired and ''why'', relative to safeguards and security objectives

  8. Coming up short on nonfinancial performance measurement.

    Science.gov (United States)

    Ittner, Christopher D; Larcker, David F

    2003-11-01

    Companies in increasing numbers are measuring customer loyalty, employee satisfaction, and other nonfinancial areas of performance that they believe affect profitability. But they've failed to relate these measures to their strategic goals or establish a connection between activities undertaken and financial outcomes achieved. Failure to make such connections has led many companies to misdirect their investments and reward ineffective managers. Extensive field research now shows that businesses make some common mistakes when choosing, analyzing, and acting on their nonfinancial measures. Among these mistakes: They set the wrong performance targets because they focus too much on short-term financial results, and they use metrics that lack strong statistical validity and reliability. As a result, the companies can't demonstrate that improvements in nonfinancial measures actually affect their financial results. The authors lay out a series of steps that will allow companies to realize the genuine promise of nonfinancial performance measures. First, develop a model that proposes a causal relationship between the chosen nonfinancial drivers of strategic success and specific outcomes. Next, take careful inventory of all the data within your company. Then use established statistical methods for validating the assumed relationships and continue to test the model as market conditions evolve. Finally, base action plans on analysis of your findings, and determine whether those plans and their investments actually produce the desired results. Nonfinancial measures will offer little guidance unless you use a process for choosing and analyzing them that relies on sophisticated quantitative and qualitative inquiries into the factors actually contributing to economic results.

  9. Approaches towards airport economic performance measurement

    Directory of Open Access Journals (Sweden)

    Ivana STRYČEKOVÁ

    2011-01-01

    Full Text Available The paper aims to assess how economic benchmarking is being used by airports as a means of performance measurement and comparison of major international airports in the world. The study focuses on current benchmarking practices and methods by taking into account different factors according to which it is efficient to benchmark airports performance. As methods are considered mainly data envelopment analysis and stochastic frontier analysis. Apart from them other approaches are discussed by airports to provide economic benchmarking. The main objective of this article is to evaluate the efficiency of the airports and answer some undetermined questions involving economic benchmarking of the airports.

  10. MODERN INSTRUMENTS FOR MEASURING ORGANIZATIONAL PERFORMANCE

    Directory of Open Access Journals (Sweden)

    RADU CATALINA

    2010-12-01

    Full Text Available Any significant management action can be assessed both in terms of success of immediate goals and as effect of the organization ability to embrace change. Market competition intensifies with the development of Romanian society and its needs. Companies that offer different products and services need to impose certain advantages and to increase their performances. The paper will present modern tools for measuring and evaluating organizational performance, namely: Balanced Scorecard, Deming model and Baldrige model. We also present an example for Balance Scorecard, of an organizations belonging to the cosmetics industry.

  11. Strategic Performance Measurement of Research and Development

    DEFF Research Database (Denmark)

    Parisi, Cristiana; Rossi, Paola

    2015-01-01

    The paper used an in depth case study to investigate how firms can integrate the strategic performance measurement of R&D with the Balanced Scorecard. Moreover, the paper investigated the crucial role of controller in the decision making process of this integration.The literature review of R......-financial ratio as the R&D measures to introduce in the Balanced Scorecard.In choosing our case study, we have selected the pharmaceutical industry because of its relevant R&D investment. Within the sector we chose the Italian affiliate of a traditional industry leader, Eli Lilly Italia,that was characterized...

  12. Key indicators for organizational performance measurement

    Directory of Open Access Journals (Sweden)

    Firoozeh Haddadi

    2014-09-01

    Full Text Available Each organization for assessing the amount of utility and desirability of their activities, especially in complex and dynamic environments, requires determining and ranking the vital performance indicators. Indicators provide essential links among strategy, execution and ultimate value creation. The aim of this paper is to develop a framework, which identifies and prioritizes Key Performance Indicators (KPIs that a company should focus on them to define and measure progress towards organizational objectives. For this purpose, an applied research was conducted in 2013 in an Iranian telecommunication company. We first determined the objectives of the company with respect to four perspectives of BSC (Balanced Scorecard framework. Next, performance indicators were listed and paired wise comparisons were accomplished by company's high-ranked employees through standard Analytic Hierarchy Process (AHP questionnaires. This helped us establish the weight of each indicator and to rank them, accordingly.

  13. Measurement-based reliability/performability models

    Science.gov (United States)

    Hsueh, Mei-Chen

    1987-01-01

    Measurement-based models based on real error-data collected on a multiprocessor system are described. Model development from the raw error-data to the estimation of cumulative reward is also described. A workload/reliability model is developed based on low-level error and resource usage data collected on an IBM 3081 system during its normal operation in order to evaluate the resource usage/error/recovery process in a large mainframe system. Thus, both normal and erroneous behavior of the system are modeled. The results provide an understanding of the different types of errors and recovery processes. The measured data show that the holding times in key operational and error states are not simple exponentials and that a semi-Markov process is necessary to model the system behavior. A sensitivity analysis is performed to investigate the significance of using a semi-Markov process, as opposed to a Markov process, to model the measured system.

  14. Team performance measures for abnormal plant operations

    International Nuclear Information System (INIS)

    Montgomery, J.C.; Seaver, D.A.; Holmes, C.W.; Gaddy, C.D.; Toquam, J.L.

    1990-01-01

    In order to work effectively, control room crews need to possess well-developed team skills. Extensive research supports the notion that improved quality and effectiveness are possible when a group works together, rather than as individuals. The Nuclear Regulatory Commission (NRC) has recognized the role of team performance in plant safety and has attempted to evaluate licensee performance as part of audits, inspections, and reviews. However, reliable and valid criteria for team performance have not yet been adequately developed. The purpose of the present research was to develop such reliable and valid measures of team skills. Seven dimensions of team skill performance were developed on the basis of input from NRC operator licensing examiners and from the results of previous research and experience in the area. These dimensions included two-way communications, resource management, inquiry, advocacy, conflict resolution/decision-making, stress management, and team spirit. Several different types of rating formats were developed for use with these dimensions, including a modified Behaviorally Anchored Rating Scale (BARS) format and a Behavioral Frequency format. Following pilot-testing and revision, observer and control room crew ratings of team performance were obtained using 14 control room crews responding to simulator scenarios at a BWR and a PWR reactor. It is concluded, overall, that the Behavioral Frequency ratings appeared quite promising as a measure of team skills but that additional statistical analyses and other follow-up research are needed to refine several of the team skills dimensions and to make the scales fully functional in an applied setting

  15. Long-term variation in the winter resident bird community of Guanica Forest, Puerto Rico: lessons for measuring and monitoring species richness.

    Science.gov (United States)

    John Faaborg; Katie M. Dugger; Wayne J. Arendt

    2007-01-01

    Because the winter season is potentially limiting for migratory birds, understanding their nonbreeding distributional patterns is essential. At a given site, patterns of species occurrence and abundance may vary over time and, within a species, wintering strategies may vary with regard to the degree that individuals are site-faithful both within and between winters. We...

  16. Performance measurement with fuzzy data envelopment analysis

    CERN Document Server

    Tavana, Madjid

    2014-01-01

    The intensity of global competition and ever-increasing economic uncertainties has led organizations to search for more efficient and effective ways to manage their business operations.  Data envelopment analysis (DEA) has been widely used as a conceptually simple yet powerful tool for evaluating organizational productivity and performance. Fuzzy DEA (FDEA) is a promising extension of the conventional DEA proposed for dealing with imprecise and ambiguous data in performance measurement problems. This book is the first volume in the literature to present the state-of-the-art developments and applications of FDEA. It is designed for students, educators, researchers, consultants and practicing managers in business, industry, and government with a basic understanding of the DEA and fuzzy logic concepts.

  17. IASI instrument: technical description and measured performances

    Science.gov (United States)

    Hébert, Ph.; Blumstein, D.; Buil, C.; Carlier, T.; Chalon, G.; Astruc, P.; Clauss, A.; Siméoni, D.; Tournier, B.

    2017-11-01

    IASI is an infrared atmospheric sounder. It will provide meteorologist and scientific community with atmospheric spectra. The IASI system includes 3 instruments that will be mounted on the Metop satellite series, a data processing software integrated in the EPS (EUMETSAT Polar System) ground segment and a technical expertise centre implemented in CNES Toulouse. The instrument is composed of a Fourier transform spectrometer and an associated infrared imager. The optical configuration is based on a Michelson interferometer and the interferograms are processed by an on-board digital processing subsystem, which performs the inverse Fourier transforms and the radiometric calibration. The infrared imager co-registers the IASI soundings with AVHRR imager (AVHRR is another instrument on the Metop satellite). The presentation will focus on the architectures of the instrument, the description of the implemented technologies and the measured performance of the first flight model. CNES is leading the IASI program in association with EUMETSAT. The instrument Prime is ALCATEL SPACE.

  18. Measuring the performance of maintenance service outsourcing.

    Science.gov (United States)

    Cruz, Antonio Miguel; Rincon, Adriana Maria Rios; Haugan, Gregory L

    2013-01-01

    The aims of this paper are (1) to identify the characteristics of maintenance service providers that directly impact maintenance service quality, using 18 independent covariables; (2) to quantify the change in risk these covariables present to service quality, measured in terms of equipment turnaround time (TAT). A survey was applied to every maintenance service provider (n = 19) for characterization purposes. The equipment inventory was characterized, and the TAT variable recorded and monitored for every work order of each service provider (N = 1,025). Finally, the research team conducted a statistical analysis to accomplish the research objectives. The results of this study offer strong empirical evidence that the most influential variables affecting the quality of maintenance service performance are the following: type of maintenance, availability of spare parts in the country, user training, technological complexity of the equipment, distance between the company and the hospital, and the number of maintenance visits performed by the company. The strength of the results obtained by the Cox model built are supported by the measure of the Rp,e(2) = 0.57 with a value of Rp,e= 0.75. Thus, the model explained 57% of the variation in equipment TAT, with moderate high positive correlation between the dependent variable (TAT) and independent variables.

  19. Personal exposure measurements of school-children to fine particulate matter (PM2.5) in winter of 2013, Shanghai, China.

    Science.gov (United States)

    Zhang, Lijun; Guo, Changyi; Jia, Xiaodong; Xu, Huihui; Pan, Meizhu; Xu, Dong; Shen, Xianbiao; Zhang, Jianghua; Tan, Jianguo; Qian, Hailei; Dong, Chunyang; Shi, Yewen; Zhou, Xiaodan; Wu, Chen

    2018-01-01

    The aim of this study was to perform an exposure assessment of PM2.5 (particulate matter less than 2.5μm in aerodynamic diameter) among children and to explore the potential sources of exposure from both indoor and outdoor environments. In terms of real-time exposure measurements of PM2.5, we collected data from 57 children aged 8-12 years (9.64 ± 0.93 years) in two schools in Shanghai, China. Simultaneously, questionnaire surveys and time-activity diaries were used to estimate the environment at home and daily time-activity patterns in order to estimate the exposure dose of PM2.5 in these children. Principle component regression analysis was used to explore the influence of potential sources of PM2.5 exposure. All the median personal exposure and microenvironment PM2.5 concentrations greatly exceeded the daily 24-h PM2.5 Ambient Air Quality Standards of China, the USA, and the World Health Organization (WHO). The median Etotal (the sum of the PM2.5 exposure levels in different microenvironment and fractional time) of all students was 3014.13 (μg.h)/m3. The concentration of time-weighted average (TWA) exposure of all students was 137.01 μg/m3. The median TWA exposure level during the on-campus period (135.81 μg/m3) was significantly higher than the off-campus period (115.50 μg/m3, P = 0.013 < 0.05). Besides ambient air pollution and meteorological conditions, storey height of the classroom and mode of transportation to school were significantly correlated with children's daily PM2.5 exposure. Children in the two selected schools were exposed to high concentrations of PM2.5 in winter of 2013 in Shanghai. Their personal PM2.5 exposure was mainly associated with ambient air conditions, storey height of the classroom, and children's transportation mode to school.

  20. Human performance assessment: methods and measures

    International Nuclear Information System (INIS)

    Andresen, Gisle; Droeivoldsmo, Asgeir

    2000-10-01

    The Human Error Analysis Project (HEAP) was initiated in 1994. The aim of the project was to acquire insights on how and why cognitive errors occur when operators are engaged in problem solving in advanced integrated control rooms. Since human error had not been studied in the HAlden Man-Machine LABoratory (HAMMLAB) before, it was also necessary to carry out research in methodology. In retrospect, it is clear that much of the methodological work is relevant to human-machine research in general, and not only to research on human error. The purpose of this report is, therefore, to give practitioners and researchers an overview of the methodological parts of HEAP. The scope of the report is limited to methods used throughout the data acquisition process, i.e., data-collection methods, data-refinement methods, and measurement methods. The data-collection methods include various types of verbal protocols, simulator logs, questionnaires, and interviews. Data-refinement methods involve different applications of the Eyecon system, a flexible data-refinement tool, and small computer programs used for rearranging, reformatting, and aggregating raw-data. Measurement methods involve assessment of diagnostic behaviour, erroneous actions, complexity, task/system performance, situation awareness, and workload. The report concludes that the data-collection methods are generally both reliable and efficient. The data-refinement methods, however, should be easier to use in order to facilitate explorative analyses. Although the series of experiments provided an opportunity for measurement validation, there are still uncertainties connected to several measures, due to their reliability still being unknown. (Author). 58 refs.,7 tabs

  1. Increasing Winter Maximal Metabolic Rate Improves Intrawinter Survival in Small Birds.

    Science.gov (United States)

    Petit, Magali; Clavijo-Baquet, Sabrina; Vézina, François

    Small resident bird species living at northern latitudes increase their metabolism in winter, and this is widely assumed to improve their chances of survival. However, the relationship between winter metabolic performance and survival has yet to be demonstrated. Using capture-mark-recapture, we followed a population of free-living black-capped chickadees (Poecile atricapillus) over 3 yr and evaluated their survival probability within and among winters. We also measured the size-independent body mass (M s ), hematocrit (Hct), basal metabolic rate (BMR), and maximal thermogenic capacity (Msum) and investigated how these parameters influenced survival within and among winters. Results showed that survival probability was high and constant both within (0.92) and among (0.96) winters. They also showed that while M s , Hct, and BMR had no significant influence, survival was positively related to Msum-following a sigmoid relationship-within but not among winter. Birds expressing an Msum below 1.26 W (i.e., similar to summer levels) had a winter. Our data therefore suggest that black-capped chickadees that are either too slow or unable to adjust their phenotype from summer to winter have little chances of survival and thus that seasonal upregulation of metabolic performance is highly beneficial. This study is the first to document in an avian system the relationship between thermogenic capacity and winter survival, a proxy of fitness.

  2. Does wintering north or south of the Sahara correlate with timing and breeding performance in black-tailed godwits?

    NARCIS (Netherlands)

    Kentie, Rosemarie; Marquez-Ferrando, Rocío; Figuerola, Jordi; Gangoso, Laura; Hooijmeijer, Jos C E W; Loonstra, A. H Jelle; Robin, Frédéric; Sarasa, Mathieu; Senner, Nathan; Valkema, Haije; Verhoeven, Mo A.; Piersma, Theunis

    2017-01-01

    Migrating long distances requires time and energy, and may interact with an individual's performance during breeding. These seasonal interactions in migratory animals are best described in populations with disjunct nonbreeding distributions. The black-tailed godwit (Limosa limosa limosa), which

  3. Measured winter and spring-time indoor temperatures in UK homes over the period 1969–2010: A review and synthesis

    International Nuclear Information System (INIS)

    Vadodaria, K.; Loveday, D.L.; Haines, V.

    2014-01-01

    This paper presents a review and synthesis of average winter and spring-time indoor temperatures in UK homes measured over the period 1969–2010. Analysis of measured temperatures in a sample of solid wall dwellings in the UK, conducted as part of the CALEBRE research project, is included. The review suggests that, for periods when occupation was likely, there has been little or no increase in winter and spring-time average living room temperatures over the last 40 years, with average recorded living room temperatures having been historically lower than the WHO-recommended value of 21 °C. Correspondingly, for periods of likely occupation, average bedroom temperatures appear to have increased. Compared with non-domestic buildings, there have been fewer investigations of domestic thermal comfort, either in the UK or elsewhere, and hence the paper also calls for further detailed investigations of domestic indoor temperatures during occupied hours together with thermal comfort evaluations in order to better understand domestic thermal environments. Based on suggestions from the limited range of studies available to date, living room temperatures may need to be maintained within the range 20–22 °C for thermal satisfaction, though this requires confirmation through further research. The study also emphasises that improving the energy efficiency of homes should be the primary means to effect any increases in indoor temperatures that are deemed essential. Considerations for future policy are discussed. - Highlights: • We review indoor temperatures measured in UK homes during 1960-2010. • We present analysis of temperature recorded by our study in 20 UK homes. • Little or no increase observed in living room temperatures for the last 40 years. • Occupied bedroom temperatures appear to have increased. • Living room temperatures have been historically lower than the WHO guidelines

  4. Performance measurements of hybrid PIN diode arrays

    International Nuclear Information System (INIS)

    Jernigan, J.G.; Arens, J.F.; Collins, T.; Herring, J.; Shapiro, S.L.; Wilburn, C.D.

    1990-05-01

    We report on the successful effort to develop hybrid PIN diode arrays and to demonstrate their potential as components of vertex detectors. Hybrid pixel arrays have been fabricated by the Hughes Aircraft Co. by bump bonding readout chips developed by Hughes to an array of PIN diodes manufactured by Micron Semiconductor Inc. These hybrid pixel arrays were constructed in two configurations. One array format having 10 x 64 pixels, each 120 μm square, and the other format having 256 x 256 pixels, each 30 μm square. In both cases, the thickness of the PIN diode layer is 300 μm. Measurements of detector performance show that excellent position resolution can be achieved by interpolation. By determining the centroid of the charge cloud which spreads charge into a number of neighboring pixels, a spatial resolution of a few microns has been attained. The noise has been measured to be about 300 electrons (rms) at room temperature, as expected from KTC and dark current considerations, yielding a signal-to-noise ratio of about 100 for minimum ionizing particles. 4 refs., 13 figs

  5. VPN (Virtual Private Network) Performance Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Calderon, Calixto; Goncalves, Joao G.M.; Sequeira, Vitor [Joint Research Centre, Ispra (Italy). Inst. for the Protection and Security of the Citizen; Vandaele, Roland; Meylemans, Paul [European Commission, DG-TREN (Luxembourg)

    2003-05-01

    Virtual Private Networks (VPN) is an important technology allowing for secure communications through insecure transmission media (i.e., Internet) by adding authentication and encryption to the existing protocols. This paper describes some VPN performance indicators measured over international communication links. An ISDN based VPN link was established between the Joint Research Centre, Ispra site, Italy, and EURATOM Safeguards in Luxembourg. This link connected two EURATOM Safeguards FAST surveillance stations, and used different vendor solutions hardware (Cisco router 1720 and Nokia CC-500 Gateway). To authenticate and secure this international link, we have used several methods at the different levels of the seven-layered ISO network protocol stack (i.e., Callback feature, CHAP - Challenge Handshake Protocol - authentication protocol). The tests made involved the use of different encryption algorithms and the way session secret keys are periodically renewed, considering these elements influence significantly the transmission throughput. Future tests will include the use of a wide variety of wireless media transmission and terminal equipment technologies, in particular PDAs (Personal Digital Assistants) and Notebook PCs. These tests aim at characterising the functionality of VPNs whenever field inspectors wish to contact headquarters to access information from a central archive database or transmit local measurements or documents. These technologies cover wireless transmission needs at different geographical scales: roombased level Bluetooth, floor or building level Wi-Fi and region or country level GPRS.

  6. KPI Graduate Executive Summary Report, Summer 2000-Winter 2001.

    Science.gov (United States)

    Sheridan Coll. (Ontario).

    Summarizes findings from the Key Performance Indicator Satisfaction Survey administered by Sheridan College in the summer 2000, fall 2000, and winter 2001 terms. This survey was administered in compliance with the Ontario government's efforts to increase the accountability of the Colleges of Applied Arts and Technology through the measurement of…

  7. Experimental evaluation on energy performance of innovative clean air heat pump for indoor environment control in summer and winter seasons

    DEFF Research Database (Denmark)

    Nie, Jinzhe; Fang, Lei; Olesen, Bjarne W.

    2014-01-01

    Based on the air purification capacity of regenerative silica gel rotor, an innovative clean air heat pump (CAHP) was designed, developed and investigated through experimental studies. The CAHP integrated air purification, dehumidification and heating/cooling in one unit. A prototype of the CAHP...... was developed. Laboratory experimental studies were conducted to investigate its energy performance under different outdoor climates including cold, mild-cold, mild-hot and extremely hot and humid climates. The energy performance of the CAHP was then evaluated by comparing with a conventional air source heat...... pump. The results showed that to keep same indoor air quality, the CAHP could save substantial amount of energy. For example, compared to the conventional air source heat pump, the CAHP could save up to 59%, 40%, 30% of electricity for ventilation and air conditioning in a test room in summer...

  8. Winter Weather Emergencies

    Science.gov (United States)

    Severe winter weather can lead to health and safety challenges. You may have to cope with Cold related health problems, including ... there are no guarantees of safety during winter weather emergencies, you can take actions to protect yourself. ...

  9. Winter weather demand considerations.

    Science.gov (United States)

    2015-04-01

    Winter weather has varied effects on travel behavior. Using 418 survey responses from the Northern Virginia : commuting area of Washington, D.C. and binary logit models, this study examines travel related changes under : different types of winter wea...

  10. 45 CFR 305.40 - Penalty performance measures and levels.

    Science.gov (United States)

    2010-10-01

    ... HUMAN SERVICES PROGRAM PERFORMANCE MEASURES, STANDARDS, FINANCIAL INCENTIVES, AND PENALTIES § 305.40 Penalty performance measures and levels. (a) There are three performance measures for which States must... 45 Public Welfare 2 2010-10-01 2010-10-01 false Penalty performance measures and levels. 305.40...

  11. Winter active bumblebees (Bombus terrestris achieve high foraging rates in urban Britain.

    Directory of Open Access Journals (Sweden)

    Ralph J Stelzer

    2010-03-01

    Full Text Available Foraging bumblebees are normally associated with spring and summer in northern Europe. However, there have been sightings of the bumblebee Bombus terrestris during the warmer winters in recent years in southern England. But what floral resources are they relying upon during winter and how much winter forage can they collect?To test if urban areas in the UK provide a rich foraging niche for bees we set up colonies of B. terrestris in the field during two late winter periods (2005/6 & 2006/7 in London, UK, and measured their foraging performance. Fully automatic radio-frequency identification (RFID technology was used in 2006/7 to enable us to record the complete foraging activity of individually tagged bees. The number of bumblebees present during winter (October 2007 to March 2008 and the main plants they visited were also recorded during transect walks. Queens and workers were observed throughout the winter, suggesting a second generation of bee colonies active during the winter months. Mass flowering shrubs such as Mahonia spp. were identified as important food resources. The foraging experiments showed that bees active during the winter can attain nectar and pollen foraging rates that match, and even surpass, those recorded during summer.B. terrestris in the UK are now able to utilise a rich winter foraging resource in urban parks and gardens that might at present still be under-exploited, opening up the possibility of further changes in pollinator phenology.

  12. Winter active bumblebees (Bombus terrestris) achieve high foraging rates in urban Britain.

    Science.gov (United States)

    Stelzer, Ralph J; Chittka, Lars; Carlton, Marc; Ings, Thomas C

    2010-03-05

    Foraging bumblebees are normally associated with spring and summer in northern Europe. However, there have been sightings of the bumblebee Bombus terrestris during the warmer winters in recent years in southern England. But what floral resources are they relying upon during winter and how much winter forage can they collect? To test if urban areas in the UK provide a rich foraging niche for bees we set up colonies of B. terrestris in the field during two late winter periods (2005/6 & 2006/7) in London, UK, and measured their foraging performance. Fully automatic radio-frequency identification (RFID) technology was used in 2006/7 to enable us to record the complete foraging activity of individually tagged bees. The number of bumblebees present during winter (October 2007 to March 2008) and the main plants they visited were also recorded during transect walks. Queens and workers were observed throughout the winter, suggesting a second generation of bee colonies active during the winter months. Mass flowering shrubs such as Mahonia spp. were identified as important food resources. The foraging experiments showed that bees active during the winter can attain nectar and pollen foraging rates that match, and even surpass, those recorded during summer. B. terrestris in the UK are now able to utilise a rich winter foraging resource in urban parks and gardens that might at present still be under-exploited, opening up the possibility of further changes in pollinator phenology.

  13. Winter-to-winter variations in indoor radon

    International Nuclear Information System (INIS)

    Mose, D.G.; Mushrush, G.W.; Kline, S.W.

    1989-01-01

    Indoor radon concentrations in northern Virginia and central Maryland show a strong dependence on weather. Winter tends to be associated with higher than average indoor radon, and summer with lower than average. However, compared to the winter of 1986-1987, the winter of 1987-1988 was warmer and drier. Consequently, winter-to-winter indoor radon decreased by about 25%. This winter-to-winter decrease is unexpectedly large, and simulates winter-to-summer variations that have been reported

  14. observation and analysis of the structure of winter precipitation-generating clouds using ground-based sensor measurements

    Science.gov (United States)

    Menéndez José Luis, Marcos; Gómez José Luis, Sánchez; Campano Laura, López; Ortega Eduardo, García; Suances Andrés, Merino; González Sergio, Fernández; Salvador Estíbaliz, Gascón; González Lucía, Hermida

    2015-04-01

    In this study, we used a 28-day database corresponding to December, January and February of 2011/2012 and 2012/2013 campaigns to analyze cloud structure that produced precipitation in the Sierra Norte near Madrid, Spain. We used remote sensing measurements, both active type like the K-band Micro Rain Radar (MRR) and passive type like the Radiometrics MP-3000A multichannel microwave radiometer. Using reflectivity data from the MRR, we determined the important microphysical parameters of Ice Water Content (IWC) and its integrated value over the atmospheric column, or Ice Water Path (IWP). Among the measurements taken by the MP-3000A were Liquid Water Path (LWP) and Integrated Water Vapor (IWV). By representing these data together, sharp declines in LWP and IWV were evident, coincident with IWP increases. This result indicates the ability of a K-band radar to measure the amount of ice in the atmospheric column, simultaneously revealing the Wegener-Bergeron-Findeisen mechanism. We also used a Present Weather Sensor (VPF-730; Biral Ltd., Bristol, UK) to determine the type and amount of precipitation at the surface. With these data, we used regression equations to establish the relationship between visibility and precipitation intensity. In addition, through theoretical precipitation visibility-intensity relationships, we estimated the type of crystal, degree of accretion (riming), and moisture content of fallen snow crystals.

  15. High Job Performance Through Co-Developing Performance Measures With Employees

    NARCIS (Netherlands)

    Groen, Bianca A.C.; Wilderom, Celeste P.M.; Wouters, Marc

    2017-01-01

    According to various studies, employee participation in the development of performance measures can increase job performance. This study focuses on how this job performance elevation occurs. We hypothesize that when employees have participated in the development of performance measures, they

  16. CONSIDERATIONS ON MEASURING PERFORMANCE AND MARKET STRUCTURE

    OpenAIRE

    Spiridon Cosmin Alexandru

    2011-01-01

    According to neoclassical theory, the relationship between the price, respectively of marginal cost and market structures, the methods for determining the performance of a firm or of an industry, deviate from the model of perfect competition. Assessing performance involves performing comparisons, reporting that their reference level can be a standard value, or a statistical value which can be a national-regional average, a homogeneous group, or an average value at a market level. Modern theor...

  17. Measuring individual work performance: Identifying and selecting indicators

    NARCIS (Netherlands)

    Koopmans, L.; Bernaards, C.M.; Hildebrandt, V.H.; de Vet, H.C.W.; van der Beek, A.J.

    2014-01-01

    BACKGROUND: Theoretically, individual work performance (IWP) can be divided into four dimensions: task performance, contextual performance, adaptive performance, and counterproductive work behavior. However, there is no consensus on the indicators used to measure these dimensions.

  18. Measuring individual work performance: identifying and selecting indicators

    NARCIS (Netherlands)

    Koopmans, L.; Bernaards, C.M.; Hildebrandt, V.H.; Vet, H.C de; Beek, A.J. van der

    2014-01-01

    BACKGROUND: Theoretically, individual work performance (IWP) can be divided into four dimensions: task performance, contextual performance, adaptive performance, and counterproductive work behavior. However, there is no consensus on the indicators used to measure these dimensions. OBJECTIVE: This

  19. Four dimensional data assimilation (FDDA) impacts on WRF performance in simulating inversion layer structure and distributions of CMAQ-simulated winter ozone concentrations in Uintah Basin

    Science.gov (United States)

    Tran, Trang; Tran, Huy; Mansfield, Marc; Lyman, Seth; Crosman, Erik

    2018-03-01

    Four-dimensional data assimilation (FDDA) was applied in WRF-CMAQ model sensitivity tests to study the impact of observational and analysis nudging on model performance in simulating inversion layers and O3 concentration distributions within the Uintah Basin, Utah, U.S.A. in winter 2013. Observational nudging substantially improved WRF model performance in simulating surface wind fields, correcting a 10 °C warm surface temperature bias, correcting overestimation of the planetary boundary layer height (PBLH) and correcting underestimation of inversion strengths produced by regular WRF model physics without nudging. However, the combined effects of poor performance of WRF meteorological model physical parameterization schemes in simulating low clouds, and warm and moist biases in the temperature and moisture initialization and subsequent simulation fields, likely amplified the overestimation of warm clouds during inversion days when observational nudging was applied, impacting the resulting O3 photochemical formation in the chemistry model. To reduce the impact of a moist bias in the simulations on warm cloud formation, nudging with the analysis water mixing ratio above the planetary boundary layer (PBL) was applied. However, due to poor analysis vertical temperature profiles, applying analysis nudging also increased the errors in the modeled inversion layer vertical structure compared to observational nudging. Combining both observational and analysis nudging methods resulted in unrealistically extreme stratified stability that trapped pollutants at the lowest elevations at the center of the Uintah Basin and yielded the worst WRF performance in simulating inversion layer structure among the four sensitivity tests. The results of this study illustrate the importance of carefully considering the representativeness and quality of the observational and model analysis data sets when applying nudging techniques within stable PBLs, and the need to evaluate model results

  20. Application of TRMM PR and TMI Measurements to Assess Cloud Microphysical Schemes in the MM5 Model for a Winter Storm

    Science.gov (United States)

    Han, Mei; Braun, Scott A.; Olson, William S.; Persson, P. Ola G.; Bao, Jian-Wen

    2009-01-01

    . This study employs this method to evaluate the accuracy of the simulated radiative properties by the MM5 model with different microphysical schemes. It is found that the representations of particle density, size, and mass in the different schemes in the MM5 model determine the model s performance when predicting a winter storm over the eastern Pacific Ocean. Schemes lacking moderate density particles (i.e. graupel), with snow flakes that are too large, or with excessive mass of snow or graupel lead to degraded prediction of the radiative properties as observed by the TRMM satellite. This study demonstrates the uniqueness of the combination of both an active microwave sensor (PR) and passive microwave sensor (TMI) onboard TRMM on assessing the accuracy of numerical weather forecasting. It improves our understanding of the physical and radiative properties of different types of precipitation particles and provides suggestions for better representation of cloud and precipitation processes in numerical models. It would, ultimately, contribute to answering questions like "Why did it not rain when the forecast says it would?"

  1. Developing integrated benchmarks for DOE performance measurement

    Energy Technology Data Exchange (ETDEWEB)

    Barancik, J.I.; Kramer, C.F.; Thode, Jr. H.C.

    1992-09-30

    The objectives of this task were to describe and evaluate selected existing sources of information on occupational safety and health with emphasis on hazard and exposure assessment, abatement, training, reporting, and control identifying for exposure and outcome in preparation for developing DOE performance benchmarks. Existing resources and methodologies were assessed for their potential use as practical performance benchmarks. Strengths and limitations of current data resources were identified. Guidelines were outlined for developing new or improved performance factors, which then could become the basis for selecting performance benchmarks. Data bases for non-DOE comparison populations were identified so that DOE performance could be assessed relative to non-DOE occupational and industrial groups. Systems approaches were described which can be used to link hazards and exposure, event occurrence, and adverse outcome factors, as needed to generate valid, reliable, and predictive performance benchmarks. Data bases were identified which contain information relevant to one or more performance assessment categories . A list of 72 potential performance benchmarks was prepared to illustrate the kinds of information that can be produced through a benchmark development program. Current information resources which may be used to develop potential performance benchmarks are limited. There is need to develop an occupational safety and health information and data system in DOE, which is capable of incorporating demonstrated and documented performance benchmarks prior to, or concurrent with the development of hardware and software. A key to the success of this systems approach is rigorous development and demonstration of performance benchmark equivalents to users of such data before system hardware and software commitments are institutionalized.

  2. Measuring Student Performance in General Organic Chemistry

    Science.gov (United States)

    Austin, Ara C.; Ben-Daat, Hagit; Zhu, Mary; Atkinson, Robert; Barrows, Nathan; Gould, Ian R.

    2015-01-01

    Student performance in general organic chemistry courses is determined by a wide range of factors including cognitive ability, motivation and cultural capital. Previous work on cognitive factors has tended to focus on specific areas rather than exploring performance across all problem types and cognitive skills. In this study, we have categorized…

  3. Decontamination and winter conditions

    International Nuclear Information System (INIS)

    Quenild, C.; Tveten, U.

    1984-12-01

    The report deals with two decontamonation experiments under winter conditions. A snow-covered parking lot was contaminated, and the snow was subsequently removed using standard snow-moving equipment. The snow left behind was collected and the content of contaminant was determined. A non-radioactive contaminant was used. A decontamination factor exceeding 100 was obtained. Although the eksperimental conditions were close to ideal, it is reason to believe that extremely efficient removal of deposited materials on a snow surface is achivable. In another investigation, run-off from agricultural surface, contaminated while covered with snow, was measured A lycimeter was used in this experiment. A stable layer of ice and snow was allowed to form before contamination. The run-off water was collected at each thaw period until all snow and ice was gone. Cs-134 was used as contaminant. Roughly 30% of the Cs-134 with which the area was contaminated ran off with the melt water. Following a reactor accident situation, this would have given a corresponding reduction in the long term doses. Both of these experiments show that consequence calculation assumptions, as they are currently applied to large accident assessment, tend to overestimate the consequences resulting from accidents taking place under winter conditions

  4. Learning through a Winter's Tale

    Science.gov (United States)

    Vidotto, Kristie

    2010-01-01

    In this article, the author shares her experience during the final semester of Year 11 Theatre Studies when she performed a monologue about Hermione from "The Winter's Tale". This experience was extremely significant to her because it nearly made her lose faith in one of the most important parts of her life, drama. She believes this…

  5. Performance measures for public transit mobility management.

    Science.gov (United States)

    2011-12-01

    "Mobility management is an innovative approach for managing and delivering coordinated public : transportation services that embraces the full family of public transit options. At a national level, there are : currently no industry recognized perform...

  6. Measured performance of the GTA rf systems

    International Nuclear Information System (INIS)

    Denney, P.M.; Jachim, S.P.

    1993-01-01

    This paper describes the performance of the RF systems on the Ground Test Accelerator (GTA). The RF system architecture is briefly described. Among the RF performance results presented are RF field flatness and stability, amplitude and phase control resolution, and control system bandwidth and stability. The rejection by the RF systems of beam-induced disturbances, such as transients and noise, are analyzed. The observed responses are also compared to computer-based simulations of the RF systems for validation

  7. Performance Measurement Systems in Swedish Health Care Services

    OpenAIRE

    Kollberg, Beata

    2007-01-01

    In the quality management literature, measurements are attributed great importance in improving products and processes. Systems for performance measurement assessing financial and non-financial measurements were developed in the late 1980s and early 1990s. The research on performance measurement systems has mainly been focused on the design of different performance measurement systems. Many authors are occupied with the study of the constructs of measures and developing prescriptive models of...

  8. ESRD - Clinical Performance Measures (CPM) Project

    Data.gov (United States)

    U.S. Department of Health & Human Services — Section 4558 (b) of the Balanced Budget Act (BBA) requires CMS to develop and implement by January 1, 2000, a method to measure and report the quality of renal...

  9. Measuring collections effort improves cash performance.

    Science.gov (United States)

    Shutts, Joe

    2009-09-01

    Having a satisfied work force can lead to an improved collections effort. Hiring the right people and training them ensures employee engagement. Measuring collections effort and offering incentives is key to revenue cycle success.

  10. Reduction in the balanced scorecard performance measurement ...

    African Journals Online (AJOL)

    In this paper, we compare PCA and ordinal logistic regression in ranking the manufacturing systems. In this regard we present an integrated framework for assessment and ranking of manufacturing systems based on management and organizational performance indicators. To achieve the objectives of this study, ...

  11. Measuring Institutional Performance in Higher Education.

    Science.gov (United States)

    Meyerson, Joel W., Ed.; Massy, William F., Ed.

    This collection of seven essays from the Stanford Forum for Higher Education Futures focuses on how downsizing, quality management, and reengineering have are affecting higher education. An introductory paper, "Introduction: Change in Higher Education: Its Effect on Institutional Performance," (Joel W. Meyerson and Sandra L. Johnson)…

  12. 75 FR 38725 - Service Performance Measurement

    Science.gov (United States)

    2010-07-06

    ... proposed rules against the importance of the information that is being gathered. This would have provided... Commission is adopting a final rule on service perfomance measurement and customer satisfaction. The final... is effective on August 5, 2010. FOR FURTHER INFORMATION CONTACT: Stephen L. Sharfman, General Counsel...

  13. CONFOCAL MICROSCOPY SYSTEM PERFORMANCE: LASER POWER MEASUREMENTS

    Science.gov (United States)

    Laser power abstract The reliability of the confocal laser-scanning microscope (CLSM) to obtain intensity measurements and quantify fluorescence data is dependent on using a correctly aligned machine that contains a stable laser power. The laser power test appears to be one ...

  14. Measurements of operator performance - an experimental setup

    International Nuclear Information System (INIS)

    Netland, K.

    1980-01-01

    The human has to be considered as an important element in a process control system, even if the degree of automation is extremely high. Other elements, e.g. computer, displays, etc., can to a large extent be described and quantified. The human (operator), is difficult to describe in a precise way, and it is just as difficult to predict his thinking and acting in a control room environment. Many factors influence his performance, such as: experience, motivation, level of knowledge, training, control environment, job organization, etc. These factors have to a certain degree to be described before guidelines for design of the man-process interfaces and the control room layout can be developed. For decades, the psychological science has obtained knowledge of the human mind and behaviour. This knowledge should have the potential of a positive input on our effort to describe the factors influencing the operator performance. Even if the human is complex, a better understanding of his thinking and acting, and a more precise description of the factors influencing his performance can be obtained. At OECD Halden Reactor Project an experimental set-up for such studies has been developed and implemented in the computer laboratory. The present set-up includes elements as a computer- and display-based control room, a simulator representing a nuclear power plant, training programme for the subjects, and methods for the experiments. Set-up modules allow reconfiguration of experiments. (orig./HP)

  15. Evaluating performance measures to determine training effectiveness

    International Nuclear Information System (INIS)

    Klemm, R.W.; Feiza, A.S.

    1987-01-01

    This research was conceived and dedicated to helping the CECo training organization become a more integrated part of the corporate business. The target population for this study was nuclear and fossil generating station employees who directly impacted the production of electricity. The target sample (n = 150) included: instrument, mechanical, and electrical maintenance personnel; control room operators; engineers, radiation chemists, and other technical specialists; and equipment operators and attendants. A total of four instruments were utilized by this study. Three instruments were administered to the generating station personnel. These included a demographic form, a learning style profile, and a motivational style profile. The focal instrument, a performance skills rating form, was administered to supervisory personnel. Data analysis consisted of three major parts. Part one established internal consistency through Cronbach alpha statistics. Part two provides summary statistics and breakdown tables for important variables. Part three provides inferential statistics responding to the research questions. All six Performance Skills variables discriminated significantly between the trained and non-trained groups (p .001). In all cases, the mean value for the trained group exceeded the mean value for the non-trained group. Implications for further research indicate that training does have a quantifiable effect on job performance

  16. 26 CFR 801.2 - Measuring organizational performance.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 20 2010-04-01 2010-04-01 false Measuring organizational performance. 801.2 Section 801.2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INTERNAL... REVENUE SERVICE § 801.2 Measuring organizational performance. The performance measures that comprise the...

  17. "Productivity performance measurement - follow-up"

    DEFF Research Database (Denmark)

    Kristensen, Troels

    2008-01-01

    The Danish Ministry of Health has published the third annual report on hospital productivity. This experience has contributed to policy goals becoming more detailed and ambitious. New policy goals are: to include hospital productivity measures at less aggregated levels, to include labour producti...... productivity and hospital psychiatric care, to provide web-based solutions that facilitate access to productivity data, and to develop new classifications of hospital levels related to structural reforms....

  18. An Approach to Precise Nitrogen Management Using Hand-Held Crop Sensor Measurements and Winter Wheat Yield Mapping in a Mediterranean Environment

    Directory of Open Access Journals (Sweden)

    Lucía Quebrajo

    2015-03-01

    Full Text Available Regardless of the crop production system, nutrients inputs must be controlled at or below a certain economic threshold to achieve an acceptable level of profitability. The use of management zones and variable-rate fertilizer applications is gaining popularity in precision agriculture. Many researchers have evaluated the application of final yield maps and geo-referenced geophysical measurements (e.g., apparent soil electrical conductivity-ECa as a method of establishing relatively homogeneous management zones within the same plot. Yield estimation models based on crop conditions at certain growth stages, soil nutrient statuses, agronomic factors, moisture statuses, and weed/pest pressures are a primary goal in precision agriculture. This study attempted to achieve the following objectives: (1 to investigate the potential for predicting winter wheat yields using vegetation measurements (the Normalized Difference Vegetation Index—NDVI at the beginning of the season, thereby allowing for a yield response to nitrogen (N fertilizer; and (2 evaluate the feasibility of using inexpensive optical sensor measurements in a Mediterranean environment. A field experiment was conducted in two commercial wheat fields near Seville, in southwestern Spain. Yield data were collected at harvest using a yield monitoring system (RDS Ceres II-volumetric meter installed on a combine. Wheat yield and NDVI values of 3498 ± 481 kg ha−1 and 0.67 ± 0.04 nm nm−1 (field 1 and 3221 ± 531 kg ha−1 and 0.68 ± 0.05 nm nm−1 (field 2 were obtained. In both fields, the yield and NDVI exhibited a strong Pearson correlation, with rxy = 0.64 and p < 10−4 in field 1 and rxy = 0.78 and p < 10−4 in field 2. The preliminary results indicate that hand-held crop sensor-based N management can be applied to wheat production in Spain and has the potential to increase agronomic N-use efficiency on a long-term basis.

  19. Measuring systemic performance of the Lithuanian government

    OpenAIRE

    Nakrošis, Vitalis

    2008-01-01

    This paper seeks assessing the dynamics of Lithuania's governmental perfor­mance and comparing it to other countries. It draws on a simple logical model, linking the inputs of the government to its outputs and outcomes. It was found that performance of the Lithuanian government is average and even poor, if compared with the EU aver­age or such countries as Estonia and Ireland. This is despite the fact the public mode of production is rather expensive in Lithuania and the number of public empl...

  20. Measuring performances of linux hyper visors

    International Nuclear Information System (INIS)

    Chierici, A.; Veraldi, R.; Salomoni, D.

    2009-01-01

    Virtualisation is a now proven software technology that is rapidly transforming the I T landscape and fundamentally changing the way people make computations and implement services. Recently, all major software producers (e.g., Microsoft and Red Hat) developed or acquired virtualisation technologies. Our institute (http://www.CNAF.INFN.it) is a Tier l for experiments carried on at the Large Hadron Collider at CERN (http://lhc.web.CERN.ch/lhc/) and is experiencing several benefits from virtualisation technologies, like improving fault tolerance, providing efficient hardware resource usage and increasing security. Currently, the virtualisation solution we adopted is xen, which is well supported by the Scientific Linux distribution, widely used by the High-Energy Physics (HEP) community. Since Scientific Linux is based on Red Hat E S, we felt the need to investigate performances and usability differences with the new k vm technology, recently acquired by Red Hat. The case study of this work is the Tier2 site for the LHCb experiment hosted at our institute; all major grid elements for this Tier2 run on xen virtual machines smoothly. We will investigate the impact on performance and stability that a migration to k vm would entail on the Tier2 site, as well as the effort required by a system administrator to deploy the migration.

  1. Drivers of Performance Measurement Use: Empirical Evidence from Serbia

    Directory of Open Access Journals (Sweden)

    Miloš Milosavljević

    2016-05-01

    Full Text Available In the last decades, the interest of academics and practitioners for the efficiency of performance measurement system use has grown rapidly. The aim of this paper is to examine, articulate and test the relationship between maturity of performance measurement systems, strategic compliance of performance measurement and managerial orientation, on one side, and the portfolio of performance measurement uses, on the other. Data were collected from 86 Serbian companies. The results indicate that the most influential factor for diversified use of performance measurement is the maturity of the system. The paper also discusses theoretical contributions, implications for managers and scholars, and recommendations for decision-makers.

  2. Employee participation in developing performance measures and job performance: on the role of measurement properties and incentives

    NARCIS (Netherlands)

    Groen, B.; Wouters, M.; Wilderom, C.

    2013-01-01

    Involving employees in the development of performance measures often results in better employee job performance. Yet not all prior studies find such a direct effect. This study explains these inconsistent findings. It focuses on the measurement properties of performance measures and using them for

  3. A comparative study of performance measurement standards of railway operator

    Directory of Open Access Journals (Sweden)

    Pongjirawut Siripong

    2017-01-01

    Full Text Available The European standard (EN 13816, is one of the widely accepted standards for measuring the quality of public passenger transport (PPT service. EN 13816 indicates 8 measurement criteria, 29 sub-criteria and 193 Key Performance Indicators (KPIs to be used to measure the performance of railway operators. Nowadays, there are other addition criteria beyond EN13816, developed by various organisations. This research firstly aims to explore the service performance measurement of railway operators used by actual railway operators at international level and in Thailand. After an intensive review of performance measurement standards, 9 standards are compiled and compared in terms of criteria, sub-criteria and KPIs using a cluster analysis methodology. The result found additional performance measurement aspects at 2 sub-criteria and 91 KPIs in addition to EN 13816. This research summarized and compared different performance measurement standards to measure service quality of metro rail line.

  4. Performance Measurement of Complex Event Platforms

    Directory of Open Access Journals (Sweden)

    Eva Zámečníková

    2016-12-01

    Full Text Available The aim of this paper is to find and compare existing solutions of complex event processing platforms (CEP. CEP platforms generally serve for processing and/or predicting of high frequency data. We intend to use CEP platform for processing of complex time series and integrate a solution for newly proposed method of decision making. The decision making process will be described by formal grammar. As there are lots of CEP solutions we will take the following characteristics under consideration - the processing in real time, possibility of processing of high volume data from multiple sources, platform independence, platform allowing integration with user solution and open license. At first we will talk about existing CEP tools and their specific way of use in praxis. Then we will mention the design of method for formalization of business rules used for decision making. Afterwards, we focus on two platforms which seem to be the best fit for integration of our solution and we will list the main pros and cons of each approach. Next part is devoted to benchmark platforms for CEP. Final part is devoted to experimental measurements of platform with integrated method for decision support.

  5. Winters fuels report

    International Nuclear Information System (INIS)

    1995-01-01

    The outlook for distillate fuel oil this winter is for increased demand and a return to normal inventory patterns, assuming a resumption of normal, cooler weather than last winter. With industrial production expected to grow slightly from last winter's pace, overall consumption is projected to increase 3 percent from last winter, to 3.4 million barrels per day during the heating season (October 1, 1995-March 31, 1996). Much of the supply win come from stock drawdowns and refinery production. Estimates for the winter are from the Energy Information Administration's (EIA) 4th Quarter 1995 Short-Tenn Energy Outlook (STEO) Mid-World Oil Price Case forecast. Inventories in place on September 30, 1995, of 132 million barrels were 9 percent below the unusually high year-earlier level. Inventories of high-sulfur distillate fuel oil, the principal type used for heating, were 13 percent lower than a year earlier. Supply problems are not anticipated because refinery production and the ready availability of imports should be adequate to meet demand. Residential heating off prices are expected to be somewhat higher than last winter's, as the effects of lower crude oil prices are offset by lower distillate inventories. Heating oil is forecast to average $0.92 per gallon, the highest price since the winter of 1992-93. Diesel fuel (including tax) is predicted to be slightly higher than last year at $1.13 per gallon. This article focuses on the winter assessment for distillate fuel oil, how well last year's STEO winter outlook compared to actual events, and expectations for the coming winter. Additional analyses include regional low-sulfur and high-sulfur distillate supply, demand, and prices, and recent trends in distillate fuel oil inventories

  6. Performance measurement, expectancy and agency theory: An experimental study

    NARCIS (Netherlands)

    Sloof, R.; van Praag, C.M.

    2008-01-01

    Theoretical analyses of (optimal) performance measures are typically performed within the realm of the linear agency model. This model implies that, for a given compensation scheme, the agent’s optimal effort is unrelated to the amount of noise in the performance measure. In contrast, expectancy

  7. Development of material measures for performance verifying surface topography measuring instruments

    International Nuclear Information System (INIS)

    Leach, Richard; Giusca, Claudiu; Rickens, Kai; Riemer, Oltmann; Rubert, Paul

    2014-01-01

    The development of two irregular-geometry material measures for performance verifying surface topography measuring instruments is described. The material measures are designed to be used to performance verify tactile and optical areal surface topography measuring instruments. The manufacture of the material measures using diamond turning followed by nickel electroforming is described in detail. Measurement results are then obtained using a traceable stylus instrument and a commercial coherence scanning interferometer, and the results are shown to agree to within the measurement uncertainties. The material measures are now commercially available as part of a suite of material measures aimed at the calibration and performance verification of areal surface topography measuring instruments

  8. PERFORMANCE MEASURES OF STUDENTS IN EXAMINATIONS: A STOCHASTIC APPROACH

    OpenAIRE

    Goutam Saha; GOUTAM SAHA

    2013-01-01

    Data on Secondary and Higher Secondary examination (science stream) results from Tripura (North-East India) schools are analyzed to measure the performance of students based on tests and also the performance measures of schools based on final results and continuous assessment processes are obtained. The result variation in terms of grade points in the Secondary and Higher Secondary examinations are analysed using different sets of performance measures. The transition probabilities from one g...

  9. Procedure for Measuring and Reporting Commercial Building Energy Performance

    Energy Technology Data Exchange (ETDEWEB)

    Barley, D.; Deru, M.; Pless, S.; Torcellini, P.

    2005-10-01

    This procedure is intended to provide a standard method for measuring and characterizing the energy performance of commercial buildings. The procedure determines the energy consumption, electrical energy demand, and on-site energy production in existing commercial buildings of all types. The performance metrics determined here may be compared against benchmarks to evaluate performance and verify that performance targets have been achieved.

  10. The Aviation Performance Measuring System (APMS): An Integrated Suite of Tools for Measuring Performance and Safety

    Science.gov (United States)

    Statler, Irving C.; Connor, Mary M. (Technical Monitor)

    1998-01-01

    This is a report of work in progress. In it, I summarize the status of the research and development of the Aviation Performance Measuring System (APMS) for managing, processing, and analyzing digital flight-recorded data, The objectives of the NASA-FAA APMS research project are to establish a sound scientific and technological basis for flight-data analysis, to define an open and flexible architecture for flight-data analysis systems, and to articulate guidelines for a standardized database structure on which to continue to build future flight-data-analysis extensions. APMS offers to the air transport community an open, voluntary standard for flight-data-analysis software; a standard that will help to ensure suitable functionality and data interchangeability among competing software programs. APMS will develop and document the methodologies, algorithms, and procedures for data management and analyses to enable users to easily interpret the implications regarding safety and efficiency of operations. APMS does not entail the implementation of a nationwide flight-data-collection system. It is intended to provide technical tools to ease the large-scale implementation of flight-data analyses at both the air-carrier and the national-airspace levels in support of their Flight Operations and Quality Assurance (FOQA) Programs and Advanced Qualifications Programs (AQP). APMS cannot meet its objectives unless it develops tools that go substantially beyond the capabilities of the current commercially available software and supporting analytic methods that are mainly designed to count special events. These existing capabilities, while of proven value, were created primarily with the needs-of aircrews in mind. APMS tools must serve the needs of the government and air carriers, as well as aircrews, to fully support the FOQA and AQP programs. They must be able to derive knowledge not only through the analysis of single flights (special-event detection), but also through

  11. Transportation performance measures for outcome based system management and monitoring.

    Science.gov (United States)

    2014-09-01

    The Oregon Department of Transportation (ODOT) is mature in its development and use of : performance measures, however there was not a standard approach for selecting measures nor : evaluating if existing ones were used to inform decision-making. Thi...

  12. Performance Measures for Public Participation Methods : Final Report

    Science.gov (United States)

    2018-01-01

    Public engagement is an important part of transportation project development, but measuring its effectiveness is typically piecemealed. Performance measurementdescribed by the Urban Institute as the measurement on a regular basis of the results (o...

  13. Measuring the marketing performances of state forest enterprises in ...

    African Journals Online (AJOL)

    Measuring the marketing performances of state forest enterprises in Turkey. ... This study covers a limited period of time (1999 - 2003), and 41 variables were developed in order to measure the marketing ... AJOL African Journals Online.

  14. Joint Integration Test Facility (JITF) Engineering II Performance Measurement Plans

    National Research Council Canada - National Science Library

    Boucher, Joanne

    2001-01-01

    ..., effectiveness, and accountability in federal programs and spending. The plan establishes six separate performance measurements, which correlate directly to customer satisfaction, Intelligence Mission Application (IMA...

  15. New’ Performance Measures: Determinants of Their Use and Their Impact on Performance

    NARCIS (Netherlands)

    F.H.M. Verbeeten (Frank)

    2005-01-01

    textabstractThis study investigates the extent to which Dutch organizations use ‘new’ performance measures to deal with the perceived inadequacies of traditional accounting performance measures. In addition, the determinants of the use of these ‘new’ performance measures are documented; finally, the

  16. Comparison of measured and predicted long term performance of grid a connected photovoltaic system

    International Nuclear Information System (INIS)

    Mondol, Jayanta Deb; Yohanis, Yigzaw G.; Norton, Brian

    2007-01-01

    Predicted performance of a grid connected photovoltaic (PV) system using TRNSYS was compared with measured data. A site specific global-diffuse correlation model was developed and used to calculate the beam and diffuse components of global horizontal insolation. A PV module temperature equation and a correlation relating input and output power of an inverter were developed using measured data and used in TRNSYS to perform PV array and inverter outputs simulation. Different combinations of the tilted surface radiation model, global-diffuse correlation model and PV module temperature equation were used in the simulations. Statistical error analysis was performed to compare the results for each combination. The simulation accuracy was improved by using the new global-diffuse correlation and module temperature equation in the TRNSYS simulation. For an isotropic sky tilted surface radiation model, the average monthly difference between measured and predicted PV output before and after modification of the TRNSYS component were 10.2% and 3.3%, respectively, and, for an anisotropic sky model, 15.4% and 10.7%, respectively. For inverter output, the corresponding errors were 10.4% and 3.3% and 15.8% and 8.6%, respectively. Measured PV efficiency, overall system efficiency, inverter efficiency and performance ratio of the system were compared with the predicted results. The predicted PV performance parameters agreed more closely with the measured parameters in summer than in winter. The difference between predicted performances using an isotropic and an anisotropic sky tilted surface models is between 1% and 2%

  17. Using tube rhizotrons to measure variation in depth penetration rate among modern North-European winter wheat (Triticum aestivum L.) cultivars

    DEFF Research Database (Denmark)

    Ytting, Nanna Karkov; Andersen, Sven Bode; Thorup-Kristensen, Kristian

    2014-01-01

    Deeper plant root systems are desired for improved water and nitrogen uptake in leaching environments. However, phenotyping for deep roots requires methods that enable plants to develop deep roots under realistic conditions. Winter cereals raise further complications as early growth occurs under ...

  18. Detecting management and fertilization effects on the carbon balance of winter oilseed rape with manual closed chamber measurements: Can we outrange gap-filling uncertainty and spatiotemporal variability?

    Science.gov (United States)

    Huth, Vytas; Moffat, Antje Maria; Calmet, Anna; Andres, Monique; Laufer, Judit; Pehle, Natalia; Rach, Bernd; Gundlach, Laura; Augustin, Jürgen

    2017-04-01

    Winter oilseed rape is the dominant biofuel crop in the young moraine landscape in North-Eastern Germany. However, studies on the effect of rapeseed cropping on net ecosystem exchange of CO2 (NEE) and the soil carbon (SC) balance are scarce. SC balance estimates are usually derived from long-term soil sampling field trials where rapeseed is part of different crop rotations. The estimated annual differences linked to rapeseed cropping are rather small (varying between losses of 40 g C m-2 and gains of up to 100 g C m-2). Testing management effects on the NEE and SC balance of cropping systems is best done by comparing plots with different treatments at the same site under the same climate. The soil sampling approach is in the need of field trials that run over decades, which has the disadvantage that management strategies of practical farming may have already changed when the results are derived. Continuous eddy covariance measurements of NEE would require large fields in flat terrain for each of the treatments, which is especially complicated in the heterogeneous landscapes of glacigenic origin of North-Eastern Germany. The common approach of using the chamber technique to derive NEE, however, is subject to the local soil and plant stand heterogeneities due to its tiny footprint. This technique might also disturb the ecosystem, the measurements are usually discontinuous requiring elaborate gap-filling techniques, and it has mostly been used on organic soils where large respiratory C losses occur. Therefore, our aim was to answer, if a combined approach of the eddy covariance and the chamber technique can detect the relatively small NEE and SC differences of rapeseed cropping on mineral soils within a shorter period of time than conventional soil sampling field trials can. We tested the new experimental design taking the advantages of both techniques into account: The eddy covariance tower measuring the NEE dynamics during the year; the chamber measurements to

  19. Winter Bottom Trawl Survey

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Winter Bottom Trawl Survey was initiated in 1992 and covered offshore areas from the Mid-Atlantic to Georges Bank. Inshore strata were covered...

  20. Deer Wintering Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — Deer winter habitat is critical to the long term survival of white-tailed deer (Odocoileus virginianus) in Vermont. Being near the northern extreme of the...

  1. Environmental Uncertainty, Performance Measure Variety and Perceived Performance in Icelandic Companies

    DEFF Research Database (Denmark)

    Rikhardsson, Pall; Sigurjonsson, Throstur Olaf; Arnardottir, Audur Arna

    and the perceived performance of the company. The sample was the 300 largest companies in Iceland and the response rate was 27%. Compared to other studies the majority of the respondents use a surprisingly high number of different measures – both financial and non-financial. This made testing of the three......The use of performance measures and performance measurement frameworks has increased significantly in recent years. The type and variety of performance measures in use has been researched in various countries and linked to different variables such as the external environment, performance...... measurement frameworks, and management characteristics. This paper reports the results of a study carried out at year end 2013 of the use of performance measures by Icelandic companies and the links to perceived environmental uncertainty, management satisfaction with the performance measurement system...

  2. Predicting Document Retrieval System Performance: An Expected Precision Measure.

    Science.gov (United States)

    Losee, Robert M., Jr.

    1987-01-01

    Describes an expected precision (EP) measure designed to predict document retrieval performance. Highlights include decision theoretic models; precision and recall as measures of system performance; EP graphs; relevance feedback; and computing the retrieval status value of a document for two models, the Binary Independent Model and the Two Poisson…

  3. A customer perspective on performance measurement in humanitarian supply chains

    OpenAIRE

    Schiffling, Sarah

    2013-01-01

    The increasing importance of services in SCM leads to a stronger focus on the customer perspective. Donors and beneficiaries are two distinct customer groups of humanitarian supply chains. This paper will analyse how this impacts performance measurement for example in the commonly used balanced scorecard, which includes a customer perspective. Keywords: Performance measurement, Humanitarian logistics, Customer perspective

  4. Automating Performance Measures and Clinical Practice Guidelines: Differences and Complementarities.

    Science.gov (United States)

    Tu, Samson W; Martins, Susana; Oshiro, Connie; Yuen, Kaeli; Wang, Dan; Robinson, Amy; Ashcraft, Michael; Heidenreich, Paul A; Goldstein, Mary K

    2016-01-01

    Through close analysis of two pairs of systems that implement the automated evaluation of performance measures (PMs) and guideline-based clinical decision support (CDS), we contrast differences in their knowledge encoding and necessary changes to a CDS system that provides management recommendations for patients failing performance measures. We trace the sources of differences to the implementation environments and goals of PMs and CDS.

  5. Supply chain oriented performance measurement for automotive spare parts

    NARCIS (Netherlands)

    de Leeuw, S.L.J.M.; Beekman, L.

    2008-01-01

    Literature provides a number of conceptual frameworks and discussions on performance measurement in supply chains. However, most of these frameworks focus on a single link of a supply chain. Furthermore, there is a lack of empirical analysis and case studies on performance metrics and measurements

  6. A Study on Relationships between Functional Performance and Task Performance Measure through Experiments in NPP MCR

    International Nuclear Information System (INIS)

    Jang, In Seok; Seong, Poong Hyun; Park, Jin Kyun

    2011-01-01

    Further improvements in levels of organization, management, man-machine interfaces, education, training, etc. are required, if high operating reliability of operators in huge and complex plants such as chemical plants and electrical power generating plants is to be maintained. Improvement requires good understanding of operators' behavior, including defining what is good performance for operators, especially in emergency situations. Human performance measures, therefore, are important to enhance performance and to reduce the probability of incidents and accidents in Nuclear Power Plants (NPPs). Operators' performance measures are used for multi-objectives such as control room design, human system interface evaluation, training, procedure and so on. There are two kinds of representative methods to measure operators' performance. These methods are now known as the functional performance measure and task performance measure. Functional performance measures are basically based on the plant process parameters. Functional performance measures indicate how well the operators controlled selected critical parameters. The parameters selected in this paper are derived from the four Critical Safety Functions (CSFs) identified in the emergency operating procedures such as achievement of subcriticality, maintenance of core cooling, maintenance of heat sink and maintenance of containment integrity. Task performance measures are based on the task analysis. Task analysis is to determine the tasks required and how operators are performed. In this paper, task analysis is done with ideal path for an accident completed by experts and Emergency Operation Procedure (EOP). However, most literatures related to operators' performance have been using one of these measures and there is no research to find out the relationships between two measures. In this paper, the relationships between functional performance measure and task performance measure are investigated using experiments. Shortly

  7. The relationships between common measures of glucose meter performance.

    Science.gov (United States)

    Wilmoth, Daniel R

    2012-09-01

    Glucose meter performance is commonly measured in several different ways, including the relative bias and coefficient of variation (CV), the total error, the mean absolute relative deviation (MARD), and the size of the interval around the reference value that would be necessary to contain a meter measurement at a specified probability. This fourth measure is commonly expressed as a proportion of the reference value and will be referred to as the necessary relative deviation. A deeper understanding of the relationships between these measures may aid health care providers, patients, and regulators in comparing meter performances when different measures are used. The relationships between common measures of glucose meter performance were derived mathematically. Equations are presented for calculating the total error, MARD, and necessary relative deviation using the reference value, relative bias, and CV when glucose meter measurements are normally distributed. When measurements are also unbiased, the CV, total error, MARD, and necessary relative deviation are linearly related and are therefore equivalent measures of meter performance. The relative bias and CV provide more information about meter performance than the other measures considered but may be difficult for some audiences to interpret. Reporting meter performance in multiple ways may facilitate the informed selection of blood glucose meters. © 2012 Diabetes Technology Society.

  8. MEASURING PERFORMANCE IN ORGANIZATIONS FROM MULTI-DIMENSIONAL PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    ȘTEFĂNESCU CRISTIAN

    2017-08-01

    Full Text Available In turbulent financial and economic present conditions a major challenge for the general management of organizations and in particular for the strategic human resources management is to establish a clear, coherent and consistent framework in terms of measuring organizational performance and economic efficiency. This paper aims to conduct an exploratory research of literature concerning measuring organizational performance. Based on the results of research the paper proposes a multi-dimensional model for measuring organizational performance providing a mechanism that will allow quantification of performance based on selected criteria. The model will attempt to eliminate inconsistencies and incongruities of organizational effectiveness models developed by specialists from organization theory area, performance measurement models developed by specialists from accounting management area and models of measuring the efficiency and effectiveness developed by specialists from strategic management and entrepreneurship areas.

  9. Measures of Strategic Alliance Performance, Classified and Assessed

    DEFF Research Database (Denmark)

    Christoffersen, Jeppe; Plenborg, Thomas; Robson, Matthew J.

    2014-01-01

    Over the last three decades, strategic alliance performance has been an important research topic within the international business and management fields. Researchers have investigated a number of factors explaining performance but often find diverging results. Scholars have suggested that one...... reason may be that different performance measures are used as the dependent variable. But which differences exist and how can they matter? Against this backdrop, the present study makes three main contributions. First, we identify dimensions that illustrate differences and similarities between...... performance measures and provide a simple yet comprehensive classification of the different performance measures used in 167 empirical studies in the literature. Second, we suggest how differences in performance measures may influence construct validity under different circumstances. Third, we show...

  10. Performance Measurement without Benchmarks: An Examination of Mutual Fund Returns.

    OpenAIRE

    Grinblatt, Mark; Titman, Sheridan

    1993-01-01

    This article introduces a new measure of portfolio performance and applies it to study the performance of a large sample of mutual funds. In contrast to previous studies of mutual fund performance, the measure used in this study employs portfolio holdings and does not require the use of a benchmark portfolio. It finds that the portfolio choices of mutual fund managers, particularly those that managed aggressive growth funds, earned significantly positive risk-adjusted returns in the 1976-85 p...

  11. An Examination of Organizatinal Performance Measurement System Utilization

    OpenAIRE

    DeBusk, Gerald Kenneth

    2003-01-01

    This dissertation provides results of three studies, which examine the utilization of organizational performance measurement systems. Evidence gathered in the first study provides insight into the number of perspectives or components found in the evaluation of an organization's performance and the relative weight placed on those components. The evidence suggests that the number of performance measurement components and their relative composition is situational. Components depend heavily on th...

  12. A framework to improve performance measurement in engineering projects

    OpenAIRE

    Zheng , Li; Baron , Claude; Esteban , Philippe; Xue , Rui; Zhang , Qiang

    2017-01-01

    International audience; A wide range of methods and good practices have been developed for the measurement of projects performance. They help project managers to effectively monitor the project progress and evaluate results. However, from a literature review, we noticed several remaining critical issues in measuring projects performance, such as an unbalanced development of Key Performance Indicators types between lagging and leading indicators. On the other hand, systems engineering measurem...

  13. Performance Measurement, Expectancy and Agency Theory: An Experimental Study

    OpenAIRE

    Randolph Sloof; Mirjam van Praag

    2007-01-01

    Theoretical analyses of (optimal) performance measures are typically performed within the realm of the linear agency model. An important implication of this model is that, for a given compensation scheme, the agent's optimal effort choice is unrelated to the amount of noise in the performance measure. In contrast, expectancy theory as developed by psychologists predicts that effort levels are increasing in the signal-to-noise ratio. We conduct a real effort laboratory experiment to assess the...

  14. Thermal performance measurements on ATLAS-SCT KB forward modules

    CERN Document Server

    Donegà, M; D'Onofrio, M; Ferrère, D; Hirt, C; Ikegami, Y; Kohriki, T; Kondo, T; Lindsay, S; Mangin-Brinet, M; Niinikoski, T O; Pernegger, H; Perrin, E; Taylor, G; Terada, S; Unno, Y; Wallny, R; Weber, M

    2003-01-01

    The thermal design of the KB module is presented. A Finite Elements Analysis (FEA) has been used to finalize the module design. The thermal performance of an outer irradiated KB module has been measured at different cooling conditions. The thermal runaway of the module has been measured. The FEA model has been compared with the measurements and has been used to predict the thermal performance in a realistic SCT scenario.

  15. Balanced Scorecard Based Performance Measurement & Strategic Management System

    OpenAIRE

    Permatasari, Paulina

    2006-01-01

    Developing strategy and performance measurement are an integral part of management control system. Making strategic decision about planning and controlling require information regarding how different subunits in organization work. To be effective, performance measurement, both financial and non-financial must motivate manager and employees at different levels to force goal accomplishment and organization strategic. An organization's measurement system strongly affects the behavior of people b...

  16. Performance measurement in healthcare: part II--state of the science findings by stage of the performance measurement process.

    Science.gov (United States)

    Adair, Carol E; Simpson, Elizabeth; Casebeer, Ann L; Birdsell, Judith M; Hayden, Katharine A; Lewis, Steven

    2006-07-01

    This paper summarizes findings of a comprehensive, systematic review of the peer-reviewed and grey literature on performance measurement according to each stage of the performance measurement process--conceptualization, selection and development, data collection, and reporting and use. It also outlines implications for practice. Six hundred sixty-four articles about organizational performance measurement from the health and business literature were reviewed after systematic searches of the literature, multi-rater relevancy ratings, citation checks and expert author nominations. Key themes were extracted and summarized from the most highly rated papers for each performance measurement stage. Despite a virtually universal consensus on the potential benefits of performance measurement, little evidence currently exists to guide practice in healthcare. Issues in conceptualizing systems include strategic alignment and scope. There are debates on the criteria for selecting measures and on the types and quality of measures. Implementation of data collection and analysis systems is complex and costly, and challenges persist in reporting results, preventing unintended effects and putting findings for improvement into action. There is a need for further development and refinement of performance measures and measurement systems, with a particular focus on strategies to ensure that performance measurement leads to healthcare improvement.

  17. Performance measurement in the context of CREM and FM

    NARCIS (Netherlands)

    Riratanaphong, C.; van der Voordt, Theo; Sarasoja, AL; Jensen, PA; van der Voordt, DJM; Coenen, C

    2012-01-01

    Purpose: To discuss trends in organisational performance measurement, to identify and discuss widely used performance criteria and key performance indicators (KPIs) in general and in the fields of Facility Management (FM) and Corporate Real Estate Management (CREM), and to identify how a more

  18. Designing a performance measurement system: A case study

    NARCIS (Netherlands)

    Lohman, Clemens; Fortuin, Leonard; Wouters, Marc

    2004-01-01

    Performance measurement (PM) by means of local performance indicators (PIs) is developing into performance management at a company-wide scale. But how should PIs at various levels in the organization be incorporated into one system that can help managers, working at levels that range from

  19. Performance measurement, expectancy and agency theory: An experimental study

    NARCIS (Netherlands)

    Sloof, R.; van Praag, C.M.

    2005-01-01

    Theoretical analyses of (optimal) performance measures are typically performed within the realm of the linear agency model. An important implication of this model is that, for a given compensation scheme, the agent's optimal effort choice is unrelated to the amount of noise in the performance

  20. Designing a performance measurement system : a case study

    NARCIS (Netherlands)

    Lohman, C.T.M.; Fortuin, L.; Wouters, M.J.F.

    2004-01-01

    Performance measurement (PM) by means of local performance indicators (PIs) is developing into performance management at a company-wide scale. But how should PIs at various levels in the organization be incorporated into one system that can help managers, working at levels that range from

  1. Performance-Based Measurement: Action for Organizations and HPT Accountability

    Science.gov (United States)

    Larbi-Apau, Josephine A.; Moseley, James L.

    2010-01-01

    Basic measurements and applications of six selected general but critical operational performance-based indicators--effectiveness, efficiency, productivity, profitability, return on investment, and benefit-cost ratio--are presented. With each measurement, goals and potential impact are explored. Errors, risks, limitations to measurements, and a…

  2. Field significance of performance measures in the context of regional climate model evaluation. Part 2: precipitation

    Science.gov (United States)

    Ivanov, Martin; Warrach-Sagi, Kirsten; Wulfmeyer, Volker

    2018-04-01

    A new approach for rigorous spatial analysis of the downscaling performance of regional climate model (RCM) simulations is introduced. It is based on a multiple comparison of the local tests at the grid cells and is also known as `field' or `global' significance. The block length for the local resampling tests is precisely determined to adequately account for the time series structure. New performance measures for estimating the added value of downscaled data relative to the large-scale forcing fields are developed. The methodology is exemplarily applied to a standard EURO-CORDEX hindcast simulation with the Weather Research and Forecasting (WRF) model coupled with the land surface model NOAH at 0.11 ∘ grid resolution. Daily precipitation climatology for the 1990-2009 period is analysed for Germany for winter and summer in comparison with high-resolution gridded observations from the German Weather Service. The field significance test controls the proportion of falsely rejected local tests in a meaningful way and is robust to spatial dependence. Hence, the spatial patterns of the statistically significant local tests are also meaningful. We interpret them from a process-oriented perspective. While the downscaled precipitation distributions are statistically indistinguishable from the observed ones in most regions in summer, the biases of some distribution characteristics are significant over large areas in winter. WRF-NOAH generates appropriate stationary fine-scale climate features in the daily precipitation field over regions of complex topography in both seasons and appropriate transient fine-scale features almost everywhere in summer. As the added value of global climate model (GCM)-driven simulations cannot be smaller than this perfect-boundary estimate, this work demonstrates in a rigorous manner the clear additional value of dynamical downscaling over global climate simulations. The evaluation methodology has a broad spectrum of applicability as it is

  3. Performance Measure as Feedback Variable in Image Processing

    Directory of Open Access Journals (Sweden)

    Ristić Danijela

    2006-01-01

    Full Text Available This paper extends the view of image processing performance measure presenting the use of this measure as an actual value in a feedback structure. The idea behind is that the control loop, which is built in that way, drives the actual feedback value to a given set point. Since the performance measure depends explicitly on the application, the inclusion of feedback structures and choice of appropriate feedback variables are presented on example of optical character recognition in industrial application. Metrics for quantification of performance at different image processing levels are discussed. The issues that those metrics should address from both image processing and control point of view are considered. The performance measures of individual processing algorithms that form a character recognition system are determined with respect to the overall system performance.

  4. GRAPH THEORY APPROACH TO QUANTIFY UNCERTAINTY OF PERFORMANCE MEASURES

    Directory of Open Access Journals (Sweden)

    Sérgio D. Sousa

    2015-03-01

    Full Text Available In this work, the performance measurement process is studied to quantify the uncertainty induced in the resulting performance measure (PM. To that end, the causes of uncertainty are identified, analysing the activities undertaken in the three following stages of the performance measurement process: design and implementation, data collection and record, and determination and analysis. A quantitative methodology based on graph theory and on the sources of uncertainty of the performance measurement process is used to calculate an uncertainty index to evaluate the level of uncertainty of a given PM or (key performance indicator. An application example is presented. The quantification of PM uncertainty could contribute to better represent the risk associated with a given decision and also to improve the PM to increase its precision and reliability.

  5. Multi-instance dictionary learning via multivariate performance measure optimization

    KAUST Repository

    Wang, Jim Jing-Yan

    2016-12-29

    The multi-instance dictionary plays a critical role in multi-instance data representation. Meanwhile, different multi-instance learning applications are evaluated by specific multivariate performance measures. For example, multi-instance ranking reports the precision and recall. It is not difficult to see that to obtain different optimal performance measures, different dictionaries are needed. This observation motives us to learn performance-optimal dictionaries for this problem. In this paper, we propose a novel joint framework for learning the multi-instance dictionary and the classifier to optimize a given multivariate performance measure, such as the F1 score and precision at rank k. We propose to represent the bags as bag-level features via the bag-instance similarity, and learn a classifier in the bag-level feature space to optimize the given performance measure. We propose to minimize the upper bound of a multivariate loss corresponding to the performance measure, the complexity of the classifier, and the complexity of the dictionary, simultaneously, with regard to both the dictionary and the classifier parameters. In this way, the dictionary learning is regularized by the performance optimization, and a performance-optimal dictionary is obtained. We develop an iterative algorithm to solve this minimization problem efficiently using a cutting-plane algorithm and a coordinate descent method. Experiments on multi-instance benchmark data sets show its advantage over both traditional multi-instance learning and performance optimization methods.

  6. Multi-instance dictionary learning via multivariate performance measure optimization

    KAUST Repository

    Wang, Jim Jing-Yan; Tsang, Ivor Wai-Hung; Cui, Xuefeng; Lu, Zhiwu; Gao, Xin

    2016-01-01

    The multi-instance dictionary plays a critical role in multi-instance data representation. Meanwhile, different multi-instance learning applications are evaluated by specific multivariate performance measures. For example, multi-instance ranking reports the precision and recall. It is not difficult to see that to obtain different optimal performance measures, different dictionaries are needed. This observation motives us to learn performance-optimal dictionaries for this problem. In this paper, we propose a novel joint framework for learning the multi-instance dictionary and the classifier to optimize a given multivariate performance measure, such as the F1 score and precision at rank k. We propose to represent the bags as bag-level features via the bag-instance similarity, and learn a classifier in the bag-level feature space to optimize the given performance measure. We propose to minimize the upper bound of a multivariate loss corresponding to the performance measure, the complexity of the classifier, and the complexity of the dictionary, simultaneously, with regard to both the dictionary and the classifier parameters. In this way, the dictionary learning is regularized by the performance optimization, and a performance-optimal dictionary is obtained. We develop an iterative algorithm to solve this minimization problem efficiently using a cutting-plane algorithm and a coordinate descent method. Experiments on multi-instance benchmark data sets show its advantage over both traditional multi-instance learning and performance optimization methods.

  7. From mission to measures: performance measure development for a Teen Pregnancy Prevention Program.

    Science.gov (United States)

    Farb, Amy Feldman; Burrus, Barri; Wallace, Ina F; Wilson, Ellen K; Peele, John E

    2014-03-01

    The Office of Adolescent Health (OAH) sought to create a comprehensive set of performance measures to capture the performance of the Teen Pregnancy Prevention (TPP) program. This performance measurement system needed to provide measures that could be used internally (by both OAH and the TPP grantees) for management and program improvement as well as externally to communicate the program's progress to other interested stakeholders and Congress. This article describes the selected measures and outlines the considerations behind the TPP measurement development process. Issues faced, challenges encountered, and lessons learned have broad applicability for other federal agencies and, specifically, for TPP programs interested in assessing their own performance and progress. Published by Elsevier Inc.

  8. The nuclear winter

    International Nuclear Information System (INIS)

    Velikhow, Y.P.

    1986-01-01

    Nuclear winter is an example of possible secondary effects, and if we speak of secondary we are thinking of small-scale second-order effects, but a nuclear winter is not a second-order effect. If you calculate the amount of heat produced by a nuclear explosion, it is a very small amount which does not have any chance of changing the Earth's climate, but a nuclear explosion drives or stars some new mechanism - the mechanism of nuclear winter - after 100 megatons of dust are transferred to the upper atmosphere. Another example of such amplification is radioactive fall-out, especially long-life radioactive fall-out after the possible elimination of the nuclear power industry, nuclear storage and distribution of storage waste around the globe. This is a very powerful amplification mechanism

  9. Academic writing performance measured for research and instruction

    NARCIS (Netherlands)

    Firssova, Olga

    2012-01-01

    Firssova, O. (2011, January 19). Academic writing performance measured for research and instruction. Presentation at the ICO Course Domain specific research on learning and instruction: theories, methodology and curricular innovations, Utrecht, The Netherlands: Interuniversitair Centrum voor

  10. Academic writing performance measured for research and instruction

    NARCIS (Netherlands)

    Firssova, Olga

    2012-01-01

    Firssova, O. (2012, 19 January). Academic writing performance measured for research and instruction. Presentation given at the ICO Masterclass, Theme Domain-Specific Instruction, January 19-February 10, Utrecht, The Netherlands.

  11. Establishing and integrating performance measures : a TPCB peer exchange

    Science.gov (United States)

    2015-08-31

    This report highlights key recommendations and noteworthy practices identified at Establishing and Integrating Performance Measures Peer Exchange held on April 27-28, 2015 in Dimondale, Michigan and via video teleconference. This event was spon...

  12. Decentralization, Interdependence and Performance Measurement System Design : Sequences and Priorities

    NARCIS (Netherlands)

    Abernethy, M.; Bouwens, J.F.M.G.; van Lent, L.A.G.M.

    2001-01-01

    We investigate the determinants of decentralization and performance measurement choices in multidivisional firms.We extend the research on the economics of organizational design choices by examining the impact of two important determinants of those choices, namely, subunit interdependencies and

  13. Issues with performance measures for dynamic multi-objective optimisation

    CSIR Research Space (South Africa)

    Helbig, M

    2013-06-01

    Full Text Available Symposium on Computational Intelligence in Dynamic and Uncertain Environments (CIDUE), Mexico, 20-23 June 2013 Issues with Performance Measures for Dynamic Multi-objective Optimisation Mard´e Helbig CSIR: Meraka Institute Brummeria, South Africa...

  14. design, construction and measured performance of a single-stage

    African Journals Online (AJOL)

    2012-11-03

    Nov 3, 2012 ... Abstract. The design philosophy, construction and measured performances of a single stage, single entry centrifugal pump .... the tachometer spindle to be held against a recess in the motor shaft. The constructed centrifugal ...

  15. Growth performance and certain body measurements of ostrich ...

    African Journals Online (AJOL)

    Growth performance and certain body measurements of ostrich chicks as affected by dietary protein levels during 2–9 weeks of age. Kh M Mahrose, AI Attia, IE Ismail, DE Abou-Kassem, ME Abd El-Hack ...

  16. Procurement performance measurement system in the health care industry.

    Science.gov (United States)

    Kumar, Arun; Ozdamar, Linet; Ng, Chai Peng

    2005-01-01

    The rising operating cost of providing healthcare is of concern to health care providers. As such, measurement of procurement performance will enable competitive advantage and provide a framework for continuous improvement. The objective of this paper is to develop a procurement performance measurement system. The paper reviews the existing literature in procurement performance measurement to identify the key areas of purchasing performance. By studying the three components in the supply chain collectively with the resources, procedures and output, a model is been developed. Additionally, a balanced scorecard is proposed by establishing a set of generic measures and six perspectives. A case study conducted at the Singapore Hospital applies the conceptual model to describe the purchasing department and the activities within and outside the department. The results indicate that the material management department has already made a good start in measuring the procurement process through the implementation of the balanced scorecard. There are many data that are collected but not properly collated and utilized. Areas lacking measurement include cycle time of delivery, order processing time, effectiveness, efficiency and reliability. Though a lot of hard work was involved, the advantages of establishing a measurement system outweigh the costs and efforts involved in its implementation. Results of balanced scorecard measurements provide decision-makers with critical information on efficiency and effectiveness of the purchasing department's work. The measurement model developed could be used for any hospital procurement system.

  17. The effectiveness of performance measuring in Slovenian public libraries

    Directory of Open Access Journals (Sweden)

    Silva Novljan

    1997-01-01

    Full Text Available The article describes methods of performance measuring in Slovenian public libraries, and calls attention to the problems attached to it. The argued presumption is that the performance measuring carried out on the state level, is not always a sufficient and adequate foundation for plarming of the developmenl and functioning of an individual library which has to cater for the needs and wishes of the population in a certain area.

  18. Performance measurement of electricity suppliers using PROMETHEE and balance scorecard

    OpenAIRE

    Mona Osati; Manouchehr Omidvari

    2016-01-01

    Performance measurement in energy industry plays an important role on increasing the productivity. Electricity is also among the most essential components of energy in mega cities like Tehran. The lack of a good service in this city may result unpleasant consequences on most civilians who live in this city. This paper presents an empirical investigation to measure the performance of six major electricity contractors in city of Tehran, Iran. The study implements grey numbers to handle any unce...

  19. Holistic Performance Measurement to Achieve Sustainable Competitive Advantage

    OpenAIRE

    Keni Keni

    2013-01-01

    In the past, companies used balanced scorecard to measure its performance. Now, balanced scorecard as a performance measurement tool is no longer sufficient because business has been affected by changes to the natural environment and developing social expectations. In order to achieve sustainable competitive advantage, companies are beginning to address the risks and opportunities associated with these changes in their longer-term business planning. To turn risks into opportunities, companies...

  20. From Performance Measurement to Strategic Management Model: Balanced Scorecard

    Directory of Open Access Journals (Sweden)

    Cihat Savsar

    2015-03-01

    Full Text Available Abstract: In Today’s competitive markets, one of the main conditions of the surviving of enterprises is the necessity to have effective performance management systems. Decisions must be taken by the management according to the performance of assets. In the transition from industrial society to information society, the presence of business structures have changed and the values of non-financial assets have increased in this period. So some systems have emerged based on intangible assets and to measure them instead of tangible assets and their measurements. With economic and technological development multi-dimensional evaluation in the business couldn’t be sufficient.  Performance evaluation methods can be applied in business with an integrated approach by its accordance with business strategy, linking to reward system and cause effects link established between performance measures. Balanced scorecard is one of the commonly used in measurement methods. While it was used for the first time in 1992 as a performance measurement tool today it has been used as a strategic management model besides its conventional uses. BSC contains customer perspective, internal perspective and learning and growth perspective besides financial perspective. Learning and growth perspective is determinant of other perspectives. In order to achieve the objectives set out in the financial perspective in other dimensions that need to be accomplished, is emphasized. Establishing a causal link between performance measures and targets how to achieve specified goals with strategy maps are described.

  1. Chinese Middle School Teachers' Preferences Regarding Performance Evaluation Measures

    Science.gov (United States)

    Liu, Shujie; Xu, Xianxuan; Stronge, James H.

    2016-01-01

    Teacher performance evaluation currently is receiving unprecedented attention from policy makers, scholars, and practitioners worldwide. This study is one of the few studies of teacher perceptions regarding teacher performance measures that focus on China. We employed a quantitative dominant mixed research design to investigate Chinese teachers'…

  2. Performance measurement of workplace change in two different cultural contexts

    NARCIS (Netherlands)

    Riratanaphong, C.

    2014-01-01

    There is a growing need for performance management and performance measurement that not only covers all aspects of an organisation, but which can be applied to various situations in a changing internal and external environment. The changing organisational and external contexts, such as the

  3. English Value-Added Measures: Examining the Limitations of School Performance Measurement

    Science.gov (United States)

    Perry, Thomas

    2016-01-01

    Value-added "Progress" measures are to be introduced for all English schools in 2016 as "headline" measures of school performance. This move comes despite research highlighting high levels of instability in value-added measures and concerns about the omission of contextual variables in the planned measure. This article studies…

  4. Effectiveness of Human Research Protection Program Performance Measurements.

    Science.gov (United States)

    Tsan, Min-Fu; Nguyen, Yen

    2017-10-01

    We analyzed human research protection program performance metric data of all Department of Veterans Affairs research facilities obtained from 2010 to 2016. Among a total of 25 performance metrics, 21 (84%) showed improvement, four (16%) remained unchanged, and none deteriorated during the study period. The overall improvement from these 21 performance metrics was 81.1% ± 18.7% (mean ± SD), with a range of 30% to 100%. The four performance metrics that did not show improvement all had initial noncompliance/incidence rates of performance metrics that showed improvement ranged from 0.05% to 60%. However, of the 21 performance metrics that showed improvement, 10 had initial noncompliance/incidence rates of performance measurement is an effective tool in improving the performance of human research protection programs.

  5. Theory and Application of an Economic Performance Measure of Risk

    NARCIS (Netherlands)

    C. Niu (Cuizhen); X. Guo (Xu); M.J. McAleer (Michael); W.-K. Wong (Wing-Keung)

    2017-01-01

    textabstractHomm and Pigorsch (2012a) use the Aumann and Serrano index to develop a new economic performance measure (EPM), which is well known to have advantages over other measures. In this paper, we extend the theory by constructing a one-sample confidence interval of EPM, and construct

  6. Readiness to adopt a performance measurement system for ...

    African Journals Online (AJOL)

    Readiness to adopt a performance measurement system for substance abuse treatment: Findings from the Service Quality Measures initiative. ... system, findings show that the likelihood of adoption can be further increased through improved provider awareness and enhanced leadership support for this health innovation.

  7. Adding Shareholder Value through Project Performance Measurement, Monitoring & Control

    NARCIS (Netherlands)

    M.M. Akalu; J.R. Turner (Rodney)

    2002-01-01

    textabstractWe present the various views and methods of measuring and controlling project performance, and factors affecting a project. The review indicates that there is a shift in the type and understanding of factors of project success or failure. However, the presence of various measurement

  8. New methods for mobility performance measurement in wheelchair basketball

    NARCIS (Netherlands)

    van der Slikke, R.M.A.; Berger, MAM; Bregman, DJJ; Veeger, H.E.J.

    2016-01-01

    Increased professionalism in wheelchair sports demand a more precise and quantitative measure of individual wheelchair mobility performance, to allow it to be an evaluation measure of wheelchair setting or training optimization. This research describes the application of an inertial sensor based

  9. A measure for the batting performance of cricket players : research ...

    African Journals Online (AJOL)

    A single measure that can be used to assess the performance of batsmen in cricket is defined. This study shows how it can be used to rank batsmen. The batting ability of a batsman is generally measured by means of his average. His strike rate is, however, also very important and is often looked at as well. It will furthermore ...

  10. Measurement properties of performance-based measures to assess physical function in hip and knee osteoarthritis

    DEFF Research Database (Denmark)

    Dobson, F; Hinman, R S; Hall, M

    2012-01-01

    OBJECTIVES: To systematically review the measurement properties of performance-based measures to assess physical function in people with hip and/or knee osteoarthritis (OA). METHODS: Electronic searches were performed in MEDLINE, CINAHL, Embase, and PsycINFO up to the end of June 2012. Two...... investigating measurement properties of performance measures, including responsiveness and interpretability in people with hip and/or knee OA, is needed. Consensus on which combination of measures will best assess physical function in people with hip/and or knee OA is urgently required....

  11. Mobile Handset Performance Evaluation Using Radiation Pattern Measurements

    DEFF Research Database (Denmark)

    Nielsen, Jesper Ødum; Pedersen, Gert Frølund

    2006-01-01

    The mean effective gain is an attractive performance measure of mobile handsets, since it incorporates both directional and polarization properties of the handset and environment. In this work the mean effective gain is computed from measured spherical radiation patterns of five different mobile...... pattern is reduced. Furthermore, the frequency dependence of the mean effective gain is investigated, and a method is proposed for reducing the required number of measurements on different frequencies....

  12. Emergency medical services key performance measurement in Asian cities.

    Science.gov (United States)

    Rahman, Nik Hisamuddin; Tanaka, Hideharu; Shin, Sang Do; Ng, Yih Yng; Piyasuwankul, Thammapad; Lin, Chih-Hao; Ong, Marcus Eng Hock

    2015-01-01

    One of the key principles in the recommended standards is that emergency medical service (EMS) providers should continuously monitor the quality and safety of their services. This requires service providers to implement performance monitoring using appropriate and relevant measures including key performance indicators. In Asia, EMS systems are at different developmental phases and maturity. This will create difficultly in benchmarking or assessing the quality of EMS performance across the region. An attempt was made to compare the EMS performance index based on the structure, process, and outcome analysis. The data was collected from the Pan-Asian Resuscitation Outcome Study (PAROS) data among few Asian cities, namely, Tokyo, Osaka, Singapore, Bangkok, Kuala Lumpur, Taipei, and Seoul. The parameters of inclusions were broadly divided into structure, process, and outcome measurements. The data was collected by the site investigators from each city and keyed into the electronic web-based data form which is secured strictly by username and passwords. Generally, there seems to be a more uniformity for EMS performance parameters among the more developed EMS systems. The major problem with the EMS agencies in the cities of developing countries like Bangkok and Kuala Lumpur is inadequate or unavailable data pertaining to EMS performance. There is non-uniformity in the EMS performance measurement across the Asian cities. This creates difficulty for EMS performance index comparison and benchmarking. Hopefully, in the future, collaborative efforts such as the PAROS networking group will further enhance the standardization in EMS performance reporting across the region.

  13. The impact of multi-criteria performance measurement on business performance improvement

    Directory of Open Access Journals (Sweden)

    Fentahun Moges Kasie

    2013-06-01

    Full Text Available Purpose: The purpose of this paper is to investigate the relationship between multi-criteria performance measurement (MCPM practice and business performance improvement using the raw data collected from 33 selected manufacturing companies. In addition, it proposes modified MCPM model as an effective approach to improve business performance of manufacturing companies. Design/methodology/approach:Research paper. Primary and secondary data were collected using questionnaire survey, interview and observation of records. The methodology is to evaluate business performances of sampled manufacturing companies and the extent of utilization of crucial non-financial (lagging and non-financial (leading performance measures. The positive correlation between financial business performance and practice of MCPM is clearly shown using Pearson’s correlation coefficient analysis. Findings –This research paper indicates that companies which measure their performance using important financial and non-financial measures achieve better business performance. Even though certain companies are currently using non-financial measures, the researchers have learned that these financial measures were not integrated with each other, financial measures and strategic objectives. Research limitations/implications: The limitation of this paper is that the number of surveyed companies is small to make generalization and they are found in a single country. Further researches which incorporate a large number of companies from various developing nations are suggested to minimize the limitation of this research.Practical Implication: The paper shows that multi-dimensional performance measures with the inclusion of key leading indicator are essential to predict the future environment. But cost-accounting based financial measures are inadequate to do so. These are shown practically using Pearson’s correlation coefficient analysis. Originality/value: The significance of multi

  14. Alternative measure for performance of HLW geologic repository

    International Nuclear Information System (INIS)

    Joonhang, Ahn; Chambre, P.L.

    2001-01-01

    A repository performance model that can show effects of canister multiplicity and repository configuration has been developed. Masses of a radionuclide in the repository and in the far field are proposed as performance measures. Canister multiplicity has significant effects on the release of long-lived radionuclides from the repository. As more canisters are included in the same water stream, the radionuclide concentration in the stream increases, but becomes independent of the number of canisters for sufficiently many canisters. Effects of reduction of radionuclide mass in the repository on the repository performance are clearly observed if the canister multiplicity is taken into account and the mass-based measures are applied. (author)

  15. Determinants of the use of value-based performance measures for managerial performance evaluation

    NARCIS (Netherlands)

    Dekker, H.C.; Groot, T.L.C.M.; Schoute, M.; Wiersma, E.

    2012-01-01

    As value-based (VB) performance measures include firms' cost of capital, they are considered more congruent than earnings measures. Prior studies, however, find that their use for managerial performance evaluation is less extensive than their presumed benefits would suggest. We examine how the

  16. Shielding Performance Measurements of Spent Fuel Transportation Container

    Directory of Open Access Journals (Sweden)

    SUN Hong-chao

    2015-11-01

    Full Text Available The safety supervision of radioactive material transportation package has been further stressed and implemented. The shielding performance measurements of spent fuel transport container is the important content of supervision. However, some of the problems and difficulties reflected in practice need to be solved, such as the neutron dose rate on the surface of package is too difficult to measure exactly, the monitoring results are not always reliable, etc. The monitoring results using different spectrometers were compared and the simulation results of MCNP runs were considered. An improvement was provided to the shielding performance measurements technique and management of spent fuel transport.

  17. The comprehensive care project: measuring physician performance in ambulatory practice.

    Science.gov (United States)

    Holmboe, Eric S; Weng, Weifeng; Arnold, Gerald K; Kaplan, Sherrie H; Normand, Sharon-Lise; Greenfield, Sheldon; Hood, Sarah; Lipner, Rebecca S

    2010-12-01

    To investigate the feasibility, reliability, and validity of comprehensively assessing physician-level performance in ambulatory practice. Ambulatory-based general internists in 13 states participated in the assessment. We assessed physician-level performance, adjusted for patient factors, on 46 individual measures, an overall composite measure, and composite measures for chronic, acute, and preventive care. Between- versus within-physician variation was quantified by intraclass correlation coefficients (ICC). External validity was assessed by correlating performance on a certification exam. Medical records for 236 physicians were audited for seven chronic and four acute care conditions, and six age- and gender-appropriate preventive services. Performance on the individual and composite measures varied substantially within (range 5-86 percent compliance on 46 measures) and between physicians (ICC range 0.12-0.88). Reliabilities for the composite measures were robust: 0.88 for chronic care and 0.87 for preventive services. Higher certification exam scores were associated with better performance on the overall (r = 0.19; pmeasures and by sampling feasible numbers of patients for each condition. © Health Research and Educational Trust.

  18. Performance Measurement of Management System Standards Using the Balanced Scorecard

    Directory of Open Access Journals (Sweden)

    Jan Kopia

    2017-11-01

    Full Text Available Management system standards (MSS, such as ISO standards, TQM, etc. are widely-used standards adopted by millions of organizations worldwide. It is still an unclear question whether these standards are beneficial for an organization, besides the fact that they might be required or expected by law or customers. The question, whether MSS increase the efficiency, the output, or the performance of an organization is still discussed in scientific research. One reason might be that performance measurement itself is not fully understood or in constant development ranging from pure financial evaluations over intellectual capital rating to calculating of levels of environmental, social or economic expectations known as the Trible Bottom Line. The Balanced Scorecard is one possible solution for performance measurement on a strategic and operational level and therefore useful for the measurement of the influence of MSS within organizations. This study summarized current research in the field of performance measurement in the context of MSS and IMS and the use of BSC and quantitatively and qualitatively tests the usefulness of BSC in measuring the effect of MSSs using the Execution Premium. It was found that BSC is often used, that an average number of companies integrate their measurement initiatives of their MSSs into the BSC-process, and that a high integration of MSS into the BSC improves the organizational performance. This research is useful for researchers and practitioners in order to understand the benefits of the usage of the BSC in the context of MSS or Integrated Management Systems.

  19. Business process performance measurement: a structured literature review of indicators, measures and metrics.

    Science.gov (United States)

    Van Looy, Amy; Shafagatova, Aygun

    2016-01-01

    Measuring the performance of business processes has become a central issue in both academia and business, since organizations are challenged to achieve effective and efficient results. Applying performance measurement models to this purpose ensures alignment with a business strategy, which implies that the choice of performance indicators is organization-dependent. Nonetheless, such measurement models generally suffer from a lack of guidance regarding the performance indicators that exist and how they can be concretized in practice. To fill this gap, we conducted a structured literature review to find patterns or trends in the research on business process performance measurement. The study also documents an extended list of 140 process-related performance indicators in a systematic manner by further categorizing them into 11 performance perspectives in order to gain a holistic view. Managers and scholars can consult the provided list to choose the indicators that are of interest to them, considering each perspective. The structured literature review concludes with avenues for further research.

  20. Employment and winter construction

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Larsen, Jacob Norvig

    2011-01-01

    Reduced seasonal building activity in the construction sector is often assumed to be related to hard winter conditions for building activities and poor working conditions for construction workers, resulting in higher costs and poor quality of building products, particularly in the northern hemisp...... of contracts for workers is more likely to explain differences in seasonal activity than climatic or technological factors....

  1. Titan's Emergence from Winter

    Science.gov (United States)

    Flasar, F. Michael; Achterberg, Richard; Jennings, Donald; Schinder, Paul

    2011-01-01

    We summarize the changes in Titans thermal structure derived from Cassini CIRS and radio-occultation data during the transition from winter to early spring. Titan's surface, and middle atmosphere show noticeable seasonal change, whereas that in most of the troposphere is mated. This can be understood in terms of the relatively small radiative relaxation time in the middle atmosphere and much larger time scale in the troposphere. The surface exhibits seasonal change because the heat capacity in an annual skin depth is much smaller than that in the lowest scale height of the troposphere. Surface temperatures rise 1 K at raid and high latitudes in the winter northern hemisphere and cool in the southern hemisphere. Changes in in the middle atmosphere are more complicated. Temperatures in the middle stratosphere (approximately 1 mbar) increase by a few kelvin at mid northern latitudes, but those at high latitudes first increase as that region moves out of winter shadow, and then decrease. This probably results from the combined effect of increased solar heating as the suit moves higher in the sky and the decreased adiabatic warming as the sinking motions associated with the cross-equatorial meridional cell weaken. Consistent with this interpretation, the warm temperatures observed higher up at the winter polar stratopause cool significantly.

  2. The (mis)Measurement of M&A Performance

    DEFF Research Database (Denmark)

    Meglio, Olimpia; Risberg, Annette

    2011-01-01

    This paper seeks to further the understanding of the variety of meanings M&A scholars attach to the label “M&A performance” by providing an alternative way to interpret the claimed inconsistency of M&A research findings. While many scholars contend that the problem stems from the multiplicity of M......&A performance measures, we believe the problem rests in trying to compare different measures as if they were measuring the same feature of the organization. Through our narrative review of empirical research we analyze factors shaping the M&A – as well as the organizational – performance measurement process....... The conclusion is that it is not possible to talk about M&A performance as if it was a universal construct....

  3. Real-Time Teleguidance of a Non-Surgeon Crew Medical Officer Performing Orthopedic Surgery at the Amundsen-Scott South Pole Station During Winter-Over

    Science.gov (United States)

    Otto, Christian

    2010-01-01

    The Amundsen-Scott South Pole Research station located at the geographic South Pole, is the most isolated, permanently inhabited human outpost on Earth. Medical care is provided to station personnel by a non-surgeon crew medical officer (CMO). During the winter-over period from February to October, the station is isolated, with no incoming or outgoing flights due to severe weather conditions. In late June, four months after the station had closed for the austral winter, a 31 year old meteorologist suffered a complete rupture of his patellar tendon while sliding done an embankment. An evacuation was deemed to be too risky to aircrews due to the extreme cold and darkness. A panel of physicians from Massachusetts General Hospital, Johns Hopkins University and the University of Texas Medical Branch were able to assess the patient remotely via telemedicine and agreed that surgery was the only means to restore mobility and prevent long term disability. The lack of a surgical facility and a trained surgical team were overcome by conversion of the clinic treatment area, and intensive preparation of medical laypersons as surgical assistants. The non-surgeon CMO and CMO assistant at South Pole, were guided through the administration of spinal anesthetic, and the two-hour operative repair by medical consultants at Massachusetts General Hospital. Real-time video of the operative field, directions from the remote consultants and audio communication were provided by videoconferencing equipment, operative cameras, and high bandwidth satellite communications. In real-time, opening incision/exposure, tendon relocation, hemostatsis, and operative closure by the CMO was closely monitored and guided and by the remote consultants. The patient s subsequent physical rehabilitation over the ensuing months of isolation was also monitored remotely via telemedicine. This was the first time in South Pole s history that remote teleguidance had been used for surgery and represents a model for

  4. The use of performance measurement systems in the public sector: effects on performance

    NARCIS (Netherlands)

    Speklé, R.; Verbeeten, F.H.M.

    2014-01-01

    We study the use of performance measurement systems in the public sector. We hypothesize that the way in which these systems are being used affects organizational performance, and that these performance effects depend on contractibility. Contractibility encompasses clarity of goals, the ability to

  5. Workshop on system tuning, performance measurement and performance optimization of an RSX11M system

    International Nuclear Information System (INIS)

    Downward, J.G.

    1981-01-01

    Topics discussed include thrashing in an RSX11M system - what to do; using solid state disk emulators as the swapping device - performance improvement, performance measurement techniques; capacity planning; bis buffering; and DECNET-11M optimization - performance that can be expected for real environments

  6. Using Radiation Pattern Measurements for Mobile Handset Performance Evaluation

    DEFF Research Database (Denmark)

    Nielsen, Jesper Ødum; Pedersen, Gert Frølund

    2005-01-01

    The mean effective gain (MEG) is an attractive performance measure of mobile handsets, since it incorporates both directional and polarization properties of the handset and environment. In this work the MEG is computed from measured spherical radiation patterns of five different mobile handsets...... values obtained for different orientations of the handsets in the environments. For practical measurements it is important to minimize the measurement time. The paper includes a study of the variation in MEG when the number of samples in the spherical radiation pattern is reduced. Furthermore...

  7. The Development of NOAA Education Common Outcome Performance Measures (Invited)

    Science.gov (United States)

    Baek, J.

    2013-12-01

    The National Oceanic and Atmospheric Administration (NOAA) Education Council has embarked on an ambitious Monitoring and Evaluation (M&E) project that will allow it to assess education program outcomes and impacts across the agency, line offices, and programs. The purpose of this internal effort is to link outcome measures to program efforts and to evaluate the success of the agency's education programs in meeting the strategic goals. Using an outcome-based evaluation approach, the NOAA Education Council is developing two sets of common outcome performance measures, environmental stewardship and professional development. This presentation will examine the benefits and tradeoffs of common outcome performance measures that collect program results across a portfolio of education programs focused on common outcomes. Common outcome performance measures have a few benefits to our agency and to the climate education field at large. The primary benefit is shared understanding, which comes from our process for writing common outcome performance measures. Without a shared and agreed upon set of definitions for the measure of an outcome, the reported results may not be measuring the same things and would incorrectly indicate levels of performance. Therefore, our writing process relies on a commitment to developing a shared set of definitions based on consensus. We hope that by taking the time to debate and coming to agreement across a diverse set of programs, the strength of our common measures can indicate real progress towards outcomes we care about. An additional benefit is that these common measures can be adopted and adapted by other agencies and organizations that share similar theories of change. The measures are not without their drawbacks, and we do make tradeoffs as part of our process in order to continue making progress. We know that any measure is necessarily a narrow slice of performance. A slice that may not best represent the unique and remarkable contribution

  8. Performance measurement for ambulatory care: moving towards a new agenda.

    Science.gov (United States)

    Roski, J; Gregory, R

    2001-12-01

    Despite a shift in care delivery from inpatient to ambulatory care, performance measurement efforts for the different levels in ambulatory care settings such as individual physicians, individual clinics and physician organizations have not been widely instituted in the United States (U.S.). The Health Plan Employer Data and Information Set (HEDIS), the most widely used performance measurement set in the U.S., includes a number of measures that evaluate preventive and chronic care provided in ambulatory care facilities. While HEDIS has made important contributions to the tracking of ambulatory care quality, it is becoming increasingly apparent that the measurement set could be improved by providing quality of care information at the levels of greatest interest to consumers and purchasers of care, namely for individual physicians, clinics and physician organizations. This article focuses on the improvement opportunities for quality performance measurement systems in ambulatory care. Specific challenges to creating a sustainable performance measurement system at the level of physician organizations, such as defining the purpose of the system, the accountability logic, information and reporting needs and mechanisms for sustainable implementation, are discussed.

  9. Measuring individual work performance: identifying and selecting indicators.

    Science.gov (United States)

    Koopmans, Linda; Bernaards, Claire M; Hildebrandt, Vincent H; de Vet, Henrica C W; van der Beek, Allard J

    2014-01-01

    Theoretically, individual work performance (IWP) can be divided into four dimensions: task performance, contextual performance, adaptive performance, and counterproductive work behavior. However, there is no consensus on the indicators used to measure these dimensions. This study was designed to (1) identify indicators for each dimension, (2) select the most relevant indicators, and (3) determine the relative weight of each dimension in ratings of work performance. IWP indicators were identified from multiple research disciplines, via literature, existing questionnaires, and expert interviews. Subsequently, experts selected the most relevant indicators per dimension and scored the relative weight of each dimension in ratings of IWP. In total, 128 unique indicators were identified. Twenty-three of these indicators were selected by experts as most relevant for measuring IWP. Task performance determined 36% of the work performance rating, while the other three dimensions respectively determined 22%, 20% and 21% of the rating. Notable consensus was found on relevant indicators of IWP, reducing the number from 128 to 23 relevant indicators. This provides an important step towards the development of a standardized, generic and short measurement instrument for assessing IWP.

  10. Performance measurements at the fast flux test facility

    International Nuclear Information System (INIS)

    Baumhardt, R.J.; Newland, D.J.; Praetorius, P.R.

    1987-01-01

    In 1984, Fast Flux Test Facility (FFTF) management recognized the need to develop a measurement system that would quantify the operational performance of the FFTF and the human resources needed to operate it. Driven by declining budgets and the need to safely manage a manpower rampdown at FFTF, an early warning system was developed. Although the initiating event for the early warning system was the need to safely manage a manpower rampdown, many related uses have evolved. The initial desired objective for the FFTF performance measurements was to ensure safety and control of key performance trends. However, the early warning system has provided a more quantitative, supportable basis upon which to make decisions. From this initial narrow focus, efforts in the FFTF plant and supporting organizations are leading to measurement of and, subsequently, improvements in productivity. Pilot projects utilizing statistical process control have started with longer range productivity improvement

  11. In situ performance curves measurements of large pumps

    International Nuclear Information System (INIS)

    Anton, A

    2010-01-01

    The complex energetic system on the river Lotru in Romania comprises of a series of lakes and pumping stations and a major hydroelectric power plant: Lotru-Ciunget. All the efforts have been oriented towards the maintenance of the Pelton turbines and very little attention has been directed to the pumps. In the system, there are three large pumping stations and only in the last 5 years, the pump performances have become a concern. The performances where determined using portable ultrasonic flow meters, a Yates meter, precision manometers and appropriate electrical equipment for power measurement (Power Analiser - NORMA D4000 LEM). The measurements are not supposed to interfere with the normal operation so only a limited number of tests could be performed. Based on those tests, portions of the test curves have been measured and represented in specific diagrams.

  12. In situ performance curves measurements of large pumps

    Science.gov (United States)

    Anton, A.

    2010-08-01

    The complex energetic system on the river Lotru in Romania comprises of a series of lakes and pumping stations and a major hydroelectric power plant: Lotru-Ciunget. All the efforts have been oriented towards the maintenance of the Pelton turbines and very little attention has been directed to the pumps. In the system, there are three large pumping stations and only in the last 5 years, the pump performances have become a concern. The performances where determined using portable ultrasonic flow meters, a Yates meter, precision manometers and appropriate electrical equipment for power measurement (Power Analiser - NORMA D4000 LEM). The measurements are not supposed to interfere with the normal operation so only a limited number of tests could be performed. Based on those tests, portions of the test curves have been measured and represented in specific diagrams.

  13. Business sustainability performance measurement: Eco-ratio analysis

    Directory of Open Access Journals (Sweden)

    Collins C. Ngwakwe

    2016-12-01

    Full Text Available Eco-aware customers and stakeholders are demanding for a measurement that links environmental performance with other business operations. To bridge this seemingly measurement gap, this paper suggests ‘Eco-Ratio Analysis’ and proposes an approach for conducting eco-ratio analysis. It is argued that since accounting ratios function as a tool for evaluating corporate financial viability by management and investors, eco-ratio analysis should be brought to the fore to provide a succinct measurement about the linkage between environmental performance and conventional business performance. It is hoped that this suggestion will usher in a nuance debate and approach in the teaching, research and practice of environmental management and sustainability accounting

  14. Field experiment on spray drift: Deposition and airborne drift during application to a winter wheat crop

    NARCIS (Netherlands)

    Wolters, A.; Linnemann, V.; Zande, van de J.C.; Vereecken, H.

    2008-01-01

    A field experiment was performed to evaluate various techniques for measuring spray deposition and airborne drift during spray application to a winter wheat crop. The application of a spraying agent containing the fluorescent dye Brilliant Sulfo Flavine by a conventional boom sprayer was done

  15. Developing a performance measurement system for public research centres

    Directory of Open Access Journals (Sweden)

    Masella, C.

    2012-01-01

    Full Text Available This study aims at developing a performance measurement system (PMS for research and development (R&D activities carried out by public research centres. Public research institutions are characterized by multiple stakeholders with different needs, and the management of R&D activities requires balancing the multiple goals of different stakeholders. This characteristic is a key issue in the process of construction of the PMS. Empirical evidence is provided by an Italian public research centre, where the researchers carried out a project aimed to develop a PMS following action research principles. This project gave the possibility to researchers to interact with different stakeholders and integrate their different information needs in a comprehensive set of key performance indicators (KPIs. As a result, multidimensional framework for measuring R&D performance in a public research centre is proposed and a set of Key Performance Indicators is developed, suggesting implications for academics and practitioners.

  16. Oxide thickness measurement for monitoring fuel performance at high burnup

    International Nuclear Information System (INIS)

    Jaeger, M.A.; Van Swam, L.F.P.; Brueck-Neufeld, K.

    1991-01-01

    For on-site monitoring of the fuel performance at high burnup, Advanced Nuclear Fuels uses the linear scan eddy current method to determine the oxide thickness of irradiated Zircaloy fuel cans. Direct digital data acquisition methods are employed to collect the data on magnetic storage media. This field-proven methodology allows oxide thickness measurements and rapid interpretation of the data during the reactor outages and makes it possible to immediately reinsert the assemblies for the next operating cycle. The accuracy of the poolside measurements and data acquisition/interpretation techniques have been verified through hot cell metallographic measurements of rods previously measured in the fuel pool. The accumulated data provide a valuable database against which oxide growth models have been benchmarked and allow for effective monitoring of fuel performance. (orig.) [de

  17. Measuring business performance using indicators of ecologically sustainable organizations

    Science.gov (United States)

    Snow, Charles G., Jr.; Snow, Charles C.

    2001-02-01

    The purpose of this paper is to explore the use of ecology-based performance measures as a way of augmenting the Balanced Scorecard approach to organizational performance measurement. The Balanced Scorecard, as proposed by Kaplan and Norton, focuses on four primary dimensions; financial, internal-business-process, customer, and learning and growth perspectives. Recently, many 'green' organizational theorists have developed the concept of "Ecologically Sustainable Organizations" or ESOs, a concept rooted in open systems theory. The ESO is called upon to consider resource use and conservation as a strategy for long-term viability. This paper asserts that in order to achieve ESO status, an organization must not only measure but also reward resource conservation measures. Only by adding a fifth perspective for ecological dimensions will the entity be truly motivated toward ESO status.

  18. ROLE AND IMPORTANCE OF KEY PERFORMANCE INDICATORS MEASUREMENT

    Directory of Open Access Journals (Sweden)

    Rade Stanković

    2011-03-01

    Full Text Available Key performance indicators are financial and non financial indicators that organizations use inorder to estimate and fortify how successful they are, aiming previously established long lastinggoals. Appropriate selection of indicators that will be used for measuring is of a greatest importance.Process organization of business is necessary to be constitute in order to realize such effective andefficient system or performance measuring via KPI. Process organization also implies customerorientation and necessary flexibility in nowadays condition of global competition.Explanation of process organization, the way of KPI selection, and practical example of KPImeasuring in Toyota dealerships are presented in this paper.

  19. Performance measurement of electricity suppliers using PROMETHEE and balance scorecard

    Directory of Open Access Journals (Sweden)

    Mona Osati

    2016-06-01

    Full Text Available Performance measurement in energy industry plays an important role on increasing the productivity. Electricity is also among the most essential components of energy in mega cities like Tehran. The lack of a good service in this city may result unpleasant consequences on most civilians who live in this city. This paper presents an empirical investigation to measure the performance of six major electricity contractors in city of Tehran, Iran. The study implements grey numbers to handle any uncertainty associated with numbers. The study has also adopted four main perspectives used in balanced scorecard as part of PROMETHEE method to rank different contractors.

  20. Modelling and measurement of a moving magnet linear compressor performance

    International Nuclear Information System (INIS)

    Liang, Kun; Stone, Richard; Davies, Gareth; Dadd, Mike; Bailey, Paul

    2014-01-01

    A novel moving magnet linear compressor with clearance seals and flexure bearings has been designed and constructed. It is suitable for a refrigeration system with a compact heat exchanger, such as would be needed for CPU cooling. The performance of the compressor has been experimentally evaluated with nitrogen and a mathematical model has been developed to evaluate the performance of the linear compressor. The results from the compressor model and the measurements have been compared in terms of cylinder pressure, the ‘P–V’ loop, stroke, mass flow rate and shaft power. The cylinder pressure was not measured directly but was derived from the compressor dynamics and the motor magnetic force characteristics. The comparisons indicate that the compressor model is well validated and can be used to study the performance of this type of compressor, to help with design optimization and the identification of key parameters affecting the system transients. The electrical and thermodynamic losses were also investigated, particularly for the design point (stroke of 13 mm and pressure ratio of 3.0), since a full understanding of these can lead to an increase in compressor efficiency. - Highlights: • Model predictions of the performance of a novel moving magnet linear compressor. • Prototype linear compressor performance measurements using nitrogen. • Reconstruction of P–V loops using a model of the dynamics and electromagnetics. • Close agreement between the model and measurements for the P–V loops. • The design point motor efficiency was 74%, with potential improvements identified

  1. The Effects of Performance Measurement and Compensation on Motivation

    OpenAIRE

    Marco van Herpen; C. Mirjam van Praag; Kees Cools

    2003-01-01

    This paper analyzes empirically the relationship between pay and performance. Economic and psychological theories predict that the design and implementation of a performance measurement and compensation system affect the motivation of employees. Our survey results demonstrate a positive relationship between the perceived characteristics of the complete compensation system and extrinsic motivation. Intrinsic motivation is not affected by the design of monetary compensation, but by promotion op...

  2. Standardization of test conditions for gamma camera performance measurement

    International Nuclear Information System (INIS)

    Jordan, K.

    1982-02-01

    The way of measuring gamma camera performance is to use point sources or flood sources in air, often in combination with bar phantoms. This method has nothing in common with the use of a camera in clinical practice. Particularly in the case of low energy emitters, like Tc-99m, the influence of scattered radiation over the performance of cameras is very high. The IEC document 'Characteristics and test conditions of radionuclide imaging devices' is discussed

  3. Women in Jordanian banks and performance: Financial accounting measurement

    OpenAIRE

    Muhannad Akram Ahmad; Seif Obeid Alshbiel

    2016-01-01

    This study highlights the gender diversity issues in the banking sector taking into consideration their impact on the performance measured by profitability (ROA). As the banking sector has widely been ignored from the previous studies due to their strict system, this study empirically examined the impact of the CEO gender and board with a female director on the performance of the Jordanian commercial banks in a period from 2004 to 2013. The multiple regression analysis shows that the banks wi...

  4. Towards Effective Educational Politics through Improving the Performance Measurement System

    Directory of Open Access Journals (Sweden)

    Tuuli Reisberg

    2013-01-01

    Full Text Available Educational field is impelled to increase performance and quality, financial discipline, strategic behaviour and its goals in order to enhance “effectiveness”. As a result the incorporation of private sector management practices into the educational field is taking place. But it is important to notice that a proliferation of private managerial practices into the educational field goes along with a conflict-laden and contradictory process. Education provides an important area of implementation for techniques of performance evaluation aimed at improving the performance of public services. One of the most common conceptual frameworks in measuring organisational performance takes the form of a production function where the educational institution is seen as analogous to a company transforming inputs into outputs and outcomes through a production process. But the problems and the vagueness in determining educational system’s inputs, outputs and outcomes cause difficulties in making political decisions and that is why clear policy prescriptions have been difficult to derive. The purpose of this article is to create a discussion whether performance measurement should be a part of decision-making in educational politics. The authors debate about incorporating private sector management practices into the educational field. The debate is based on the example of evaluating the social impact in the educational field and the performance of teachers’ work in the educational system. The article consists of three parts. Firstly, the theoretical background of the performance measurement in educational field is discussed. Secondly, the important criteria for performance measurement design and political issues are argued. Thirdly, the evaluated shortcomings in Estonian educational organisations, which restrict them to be effective, are brought out. Relieving some of these shortcomings could be in authority of Estonian educational politics.

  5. Performance analysis and evaluation of direct phase measuring deflectometry

    Science.gov (United States)

    Zhao, Ping; Gao, Nan; Zhang, Zonghua; Gao, Feng; Jiang, Xiangqian

    2018-04-01

    Three-dimensional (3D) shape measurement of specular objects plays an important role in intelligent manufacturing applications. Phase measuring deflectometry (PMD)-based methods are widely used to obtain the 3D shapes of specular surfaces because they offer the advantages of a large dynamic range, high measurement accuracy, full-field and noncontact operation, and automatic data processing. To enable measurement of specular objects with discontinuous and/or isolated surfaces, a direct PMD (DPMD) method has been developed to build a direct relationship between phase and depth. In this paper, a new virtual measurement system is presented and is used to optimize the system parameters and evaluate the system's performance in DPMD applications. Four system parameters are analyzed to obtain accurate measurement results. Experiments are performed using simulated and actual data and the results confirm the effects of these four parameters on the measurement results. Researchers can therefore select suitable system parameters for actual DPMD (including PMD) measurement systems to obtain the 3D shapes of specular objects with high accuracy.

  6. Measured performance of four PWR liquid radioactive waste treatment systems

    International Nuclear Information System (INIS)

    McIsaac, C.V.; Mandler, J.W.; Stalker, A.C.

    1980-01-01

    This paper presents results of a study of the liquid radwaste treatment and boron recovery systems of four operating PWR power plants. The performance of a given system was determined from measurements of radionuclide inventories in samples drawn from demineralizers, evaporators, filters, and gaseous cleanup systems. The plants at which measurements were made are Fort Calhoun, Zion 1 and 2, Turkey Point 3 and 4, and Rancho Seco

  7. Innovation and organisational performance: A critical review of the instruments used to measure organisational performance

    Directory of Open Access Journals (Sweden)

    Tebogo Sethibe

    2016-10-01

    Full Text Available Background: Innovation is recognised as one of the most important determinant of organisational performance. Yet, the results of studies that investigate the relationship between innovation and organisational performance are inconclusive. The inconsistency has been attributed to a number of factors, which include, among others, the measures used to evaluate organisational performance. Aim: This study was set out to identify, categorise and critically analyse the instruments used to assess organisational performance when investigating the relationship between innovation and organisational performance. Setting: The study focuses on all scientific publications reporting on organisational performance, inclusive of both financial and non-financial indicators of performance, and are not limited to any specific country or industry. Methods: The systematic literature review methodology was used to identify studies which investigated the relationship between innovation and organisational performance. Once identified, articles were analysed on the way organisational performance was measured. Classification was done with reference to financial and non-financial indicators, accounting and market-based, as well as objective and subjective measures. Results: The findings show that profitability, sales growth and return on assets (ROA are the most preferred accounting-based financial measures of organisation performance. In addition, Tobin’s Q was found to be the most favoured market-based financial measure of organisational performance. The study further reveals that market share, customer satisfaction and productivity are the most popular non-financial-based measures of organisational performance. Conclusion: The use of measures of organisational performance is often left to the discussion of the researcher, which is not implicitly wrong, but does little to contribute to the body of knowledge on this important topic. Researchers are firstly urged to

  8. Composite measures for profiling hospitals on bariatric surgery performance

    Science.gov (United States)

    Dimick, Justin B.; Birkmeyer, Nancy J.; Finks, Jonathan F.; Share, David A.; English, Wayne J.; Carlin, Arthur M.; Birkmeyer, John D.

    2014-01-01

    Objective We sought to develop a novel composite measure for profiling hospital performance with bariatric surgery. Design, Setting, and Patients Using clinical registry data from the Michigan Bariatric Surgery Collaborative (MBSC), we studied all patients undergoing bariatric surgery from 2008 to 2010. For gastric bypass surgery, we used empirical Bayes techniques to create a composite measure by combining several measures, including serious complications, reoperations, and readmissions; hospital and surgeon volume; and outcomes with other, related procedures. Hospitals were ranked based on 2008-09 and placed in one of 3 groups: 3-star (top third), 2-star (middle third), and 1-star (bottom third). We assessed how well these ratings predicted outcomes in the next year (2010), compared to other widely used measures. Main Outcome Measures Risk-adjusted serious complications. Results Composite measures explained a larger proportion of hospital-level variation in serious complication rates with gastric bypass than other measures. For example, the composite measure explained 89% of the variation compared to only 28% for risk-adjusted complication rates alone. Composite measures also appeared better at predicting future performance compared to individual measures. When ranked on the composite measure, 1-star hospitals (bottom 20%), had 2-fold higher serious complication rates (4.6% vs. 2.4%; OR 2.0; 95% CI, 1.1 to 3.5) compared to 3-star (top 20%) hospitals. Differences in serious complications rates between 1-star and 3-star hospitals were much smaller when hospitals were ranked using serious complications (4.0% vs. 2.7%; OR 1.6; 95% CI, 0.8-2.9) and hospital volume (3.3% vs. 3.2%; OR 0.85; 95% CI, 0.4 to 1.7) Conclusions Composite measures are much better at explaining hospital-level variation in serious complications and predicting future performance than other approaches. In this preliminary study, it appears that such composite measures may be better than existing

  9. Measurements of IN and BIO-IN with the fast ice nucleus chamber FINCH at Mt. Zugspitze, Mt. Puy de Dôme and Jungfraujoch during fall and winter

    Science.gov (United States)

    Nillius, B.; Frank, F.; Bingemer, H.; Curtius, J.; Bundke, U.

    2013-05-01

    In this work we present IN measurements at Mt. Zugspitze, Germany, 2650 m.a.s.l., Mt. Puy de Dôme, France, 1464 m.a.s.l. and Jungfraujoch, Switzerland, 3580 m a.s.l during fall and winter 2012 with the instrument FINCH HALO (Fast Ice Nucleus Chamber for the High Altitude and LOng range research aircraft HALO). In this device the temperature and super saturation for activation of Ice Nuclei (IN) and the growth to ice crystals is obtained by mixing three gas flows of different temperatures and moisture. After the growth of IN and Cloud Condensation Nuclei (CCN) to macroscopic ice crystals and super-cooled water droplets in the development chamber, they are counted using an optical detector. The discrimination between ice and water is made by measuring the circular depolarization ratio of the backscattered laser light of each individual particle. IN are classified as biological particles by measuring their individual intrinsic-fluorescence during the winter campaigns in average 30-40 % of the IN show an intrinsic fluorescence and are supposed to be of biological origin.

  10. A Framework of Performance Measurement System for Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Dermawan Wibisono

    2012-04-01

    Full Text Available In the current dynamic environment, measuring a company’s performance becomes exceedingly complex since Performance Measurements Systems (PMS not only measure a company’s performance but also reflect their organizational culture and philosophy. Designing and implementing PMS is an integral part of management control systems. However, traditional PMS are criticized for being obsolete, irrelevant to managerial decisionmaking, unrelated to strategic objectives and detrimental to organizational improvements. Given the shortcomings of traditional PMS, there is need for a new framework that canlead to the design of a PMS that balances short-term and long-term measures, internal and external measures, and financial and operational measures. This paper presents issuesassociated with the needs of a dynamic PMS, observe past research achievements in PMS and review past PMS frameworks that have been introduced. The paper then proposes animproved methodology for the design of a realistic PMS and its effective implementation in a manufacturing environment with case for Indonesia’s company.

  11. A Framework of Performance Measurement System for Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Dermawan Wibisono

    2011-10-01

    Full Text Available In the current dynamic environment, measuring a company’s performance becomes exceedingly complex since Performance Measurements Systems (PMS not only measure a company’s performance but also reflect their organizational culture and philosophy. Designing and implementing PMS is an integral part of management control systems. However, traditional PMS are criticized for being obsolete, irrelevant to managerial decision making, unrelated to strategic objectives and detrimental to organizational improvements. Given the shortcomings of traditional PMS, there is need for a new framework that can lead to the design of a PMS that balances short-term and long-term measures, internal and external measures, and financial and operational measures. This paper presents issues associated with the needs of a dynamic PMS, observe past research achievements in PMS and review past PMS frameworks that have been introduced. The paper then proposes an improved methodology for the design of a realistic PMS and its effective implementation in a manufacturing environment with case for Indonesia’s company.

  12. Editorial - The winter Atomiades

    CERN Multimedia

    Staff Association

    2011-01-01

    As we wrote in our previous editorial, the Staff Association gives direct support to sports events, such as the Atomiades, a section of the Association of Sports Communities of European Research Institutes, which brings together sportsmen and women from 38 European research centres in 13 countries (Austria, Belgium, Czech Republic, United Kingdom, Finland, France, Germany, Hungary, Italy, Luxemburg, the Netherlands, Russia, and Switzerland). The summer Atomiades take place between the months of June and September every three years. Thirteen such events have taken place since 1973, the last one in June 2009 in Berlin. As far as the winter Atomiades are concerned, also organized every three years, and alternating with the summer Atomiades, there have been eleven since 1981, the last one at the end of January this year in neighbouring France. The following article tells the wonderful adventure of the CERN staff who took part in this event. A positive outcome for CERN skiers at the winter Atomiades The 11t...

  13. Multitasking TORT Under UNICOS: Parallel Performance Models and Measurements

    International Nuclear Information System (INIS)

    Azmy, Y.Y.; Barnett, D.A.

    1999-01-01

    The existing parallel algorithms in the TORT discrete ordinates were updated to function in a UNI-COS environment. A performance model for the parallel overhead was derived for the existing algorithms. The largest contributors to the parallel overhead were identified and a new algorithm was developed. A parallel overhead model was also derived for the new algorithm. The results of the comparison of parallel performance models were compared to applications of the code to two TORT standard test problems and a large production problem. The parallel performance models agree well with the measured parallel overhead

  14. Multitasking TORT under UNICOS: Parallel performance models and measurements

    International Nuclear Information System (INIS)

    Barnett, A.; Azmy, Y.Y.

    1999-01-01

    The existing parallel algorithms in the TORT discrete ordinates code were updated to function in a UNICOS environment. A performance model for the parallel overhead was derived for the existing algorithms. The largest contributors to the parallel overhead were identified and a new algorithm was developed. A parallel overhead model was also derived for the new algorithm. The results of the comparison of parallel performance models were compared to applications of the code to two TORT standard test problems and a large production problem. The parallel performance models agree well with the measured parallel overhead

  15. Winter is losing its cool

    Science.gov (United States)

    Feng, S.

    2017-12-01

    Winter seasons have significant societal impacts across all sectors ranging from direct human health to ecosystems, transportation, and recreation. This study quantifies the severity of winter and its spatial-temporal variations using a newly developed winter severity index and daily temperature, snowfall and snow depth. The winter severity and the number of extreme winter days are decreasing across the global terrestrial areas during 1901-2015 except the southeast United States and isolated regions in the Southern Hemisphere. These changes are dominated by winter warming, while the changes in daily snowfall and snow depth played a secondary role. The simulations of multiple CMIP5 climate models can well capture the spatial and temporal variations of the observed changes in winter severity and extremes during 1951-2005. The models are consistent in projecting a future milder winter under various scenarios. The winter severity is projected to decrease 60-80% in the middle-latitude Northern Hemisphere under the business-as-usual scenario. The winter arrives later, ends earlier and the length of winter season will be notably shorter. The changes in harsh winter in the polar regions are weak, mainly because the warming leads to more snowfall in the high latitudes.

  16. Performance tests for instruments measuring radon activity concentration

    International Nuclear Information System (INIS)

    Beck, T.R.; Buchroeder, H.; Schmidt, V.

    2009-01-01

    Performance tests of electronic instruments measuring the activity concentration of 222 Rn have been carried out with respect to the standard IEC 61577-2. In total, 9 types of instrument operating with ionization chambers or electrostatic collection have been tested for the influence of different climatic and radiological factors on the measurement characteristics. It is concluded that all types of instrument, which are commercially available, are suitable for indoor radon measurements. Because of the dependence on climatic conditions, the outdoor use is partly limited.

  17. A critical perspective on the measurement of performance in the empirical multinationality and performance literature

    DEFF Research Database (Denmark)

    Richter, Nicole Franziska; Schmidt, Robert; Ladwig, Tina J.

    2017-01-01

    used in empirical studies and the underlying theoretical streams that explain the effects on benefits and costs of multinationality. Our findings indicate that authors still largely rely on overall financial performance measures. Theoretical arguments, in contrast, refer to specific benefit and cost......This paper contributes to the core research in international business (IB), namely the relation between multinationality and performance, and is concerned with the quality of past empirical research designs. On the basis of 49 studies, we critically evaluate the match between performance measures...... positions that are better reflected in operational performance indicators. In our view, the idiosyncratic choice of the performance measures contributes to the varying results in past studies. We offer suggestions for improving future research designs....

  18. Performance of field measuring probes for SSC magnets

    International Nuclear Information System (INIS)

    Thomas, R.; Ganetis, G.; Herrera, J.; Hogue, R.; Jain, A.; Louie, W.; Marone, A.; Wanderer, P.

    1994-01-01

    Several years of experience have been acquired on the operation of probes (open-quotes molesclose quotes) constructed for the measurement of the multipole components of the magnetic fields of SSC magnets. The field is measured by rotating coils contained in a 2.4-m long tube that is pulled through the aperture of the magnet by an external device - the transporter. In addition to the measuring coils, the tube contains motors for rotating the coil and a system for sensing local vertical using gravity sensors to provide an absolute reference for the field measurements. The authors describe the steps that must be taken in order to ensure accurate, repeatable measurements; the design changes that have been motivated by difficulties encountered (noise, vibration, variations in temperature); and other performance issues. The mechanical interface between the probe and the beam tube of the magnet is also described

  19. Performance of field measuring probes for SSC magnets

    International Nuclear Information System (INIS)

    Thomas, R.; Ganetis, G.; Herrera, J.; Hogue, R.; Jain, A.; Louie, W.; Marone, A.; Wanderer, P.

    1993-01-01

    Several years of experience have been acquired on the operation of probes (''moles'') constructed for the measurement of the multipole components of the magnetic fields of SSC magnets. The field is measured by rotating coils contained in a 2.4-m long tube that is pulled through the aperture of the magnet by an external device-the transporter. In addition to the measuring coils, the tube contains motors for rotating the coil and a system for sensing local vertical using gravity sensors to provide an absolute reference for the field measurements. We describe the steps that must be taken in order to ensure accurate, repeatable measurements; the design changes that have been motivated by difficulties encountered (noise, vibration, variations in temperature); and other performance issues. The mechanical interface between the probe and the hewn tube of the magnet is also described

  20. A key performance measures for evaluating cold supply chain performance in farm industry

    Directory of Open Access Journals (Sweden)

    Shashi Shashi

    2015-08-01

    Full Text Available The main objective of this study was to develop a set of measures, evaluate their importance and effect in cold supply chain performance. This investigation reviewed previous research works on all the stages of the farm product supply chain. Based on farm product supply chain, 4 measures with 31 metrics were identified and developed to measure the cold supply chain performance. A survey was organized to establish the importance and the effect of identified measures. The 5 point Likert scale questionnaire was distributed among SC academics and practitioners. The observed finding infers that the measurement instrument was substantiating for evaluating cold supply chain performance in farm industry. The new developed metrics will help firms improve the visibility of supply among partners and in better decision making. The investigation was enfolded up through the plan of direction intended for future study.

  1. Performance measurement of workplace change: in two different cultural contexts

    Directory of Open Access Journals (Sweden)

    Chaiwat Riratanaphong

    2014-01-01

    Full Text Available Nowadays, organisations must cope with the pressure of cost reduction and efficiency in order to succeed in a highly competitive business environment. However, drivers to improve social interaction and employee’s performance and as such to contribute to organisational goals and objectives make it necessary to be concerned with other performance criteria as well, such as effectiveness, flexibility, employee satisfaction, productivity and creativity. There is a growing need for performance management and performance measurement that not only covers all aspects of an organisation, but which can be applied to various situations in a changing internal and external environment. Performance measurement methods which include an integrated perspective of performance have become essential. In addition, it has been realised that corporate real estate can contribute to organisational performance (Nourse and Roulac, 1993, De Vries et al., 2008, Lindholm, 2008, Den Heijer, 2011, Jensen et al., 2012. For this reason, worldwide organisations started to implement new ways of working in a more open and flexible work environment. Although there are various objectives and drivers of workplace change, the common objectives are to reduce costs and to increase efficiency. The changing organisational and external contexts, such as the increasing demand for talented knowledge workers and changing work patterns, have led to the development of new offices that can promote social networks and interaction among employees. The new workplace does not only aim at achieving cost efficiency, but it should also support employee satisfaction and productivity. This PhD research focuses on both themes i.e. performance measurement of workplace change. The aim of this research is to provide a conceptual framework that visualises the impact of workplace change on employees’ responses to the new work environment and to present guidelines on performance measurement of workplace

  2. Relationship between performance measurements and sale price of ...

    African Journals Online (AJOL)

    Unknown

    Abstract. The sale prices of 1 609 Dorper rams sold between 1990 and 1999 were compared with their measured performances. An analysis of variance was carried out in order to determine which variables influenced sale price. The most importance factors were classification (stud vs. commercial), auction weight and coat ...

  3. Managing for Results--Linking Performance Measures and Budgets.

    Science.gov (United States)

    McGee, William L.; Fountain, James R., Jr.

    1995-01-01

    The Government Accounting Standards Board notion of service efforts and accomplishments reporting is one step in a process of managing for results that includes strategic planning, development and use of performance measures of managing ongoing programs, and outputs to budgetary appropriation. Reports a trial application to one school district.…

  4. Key performance indicators for measuring sustainability in health ...

    African Journals Online (AJOL)

    Key performance indicators for measuring sustainability in health care industry in Malaysia. ... AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search ... Journal Home > Vol 10, No 1S (2018) > ... Next, an in-depth meeting was conducted to gain insights and feedbacks with the management of a private hospital.

  5. Investment horizons : A time-dependent measure of asset performance

    OpenAIRE

    Ingve Simonsen; Anders Johansen; Mogens H. Jensen

    2005-01-01

    We review a resent {\\em time-dependent} performance measure for economical time series -- the (optimal) investment horizon approach. For stock indices, the approach shows a pronounced gain-loss asymmetry that is {\\em not} observed for the individual stocks that comprise the index. This difference may hint towards an synchronize of the draw downs of the stocks.

  6. Introducing the Balanced Scorecard: Creating Metrics to Measure Performance

    Science.gov (United States)

    Gumbus, Andra

    2005-01-01

    This experiential exercise presents the concept of the Balanced Scorecard (BSC) and applies it in a university setting. The Balanced Scorecard was developed 12 years ago and has grown in popularity and is used by more than 50% of the Fortune 500 companies as a performance measurement and strategic management tool. The BSC expands the traditional…

  7. Measuring supply chain performance in the agri-food sector

    NARCIS (Netherlands)

    Aramyan, L.H.

    2007-01-01

    Keywords : PMS,agri-food, supply chain, efficiency, flexibility, responsiveness, food quality

    The main objective of this research is to contribute to the development of a Performance Measurement System (PMS) foragri-food supply chains that involves the entire chain (i.e. all

  8. Quantitative measures of CRE and its link with organizational performance

    NARCIS (Netherlands)

    Appel - Meulenbroek, H.A.J.A.

    2007-01-01

    For CREM (Corporate Real Estate Management) to be able to deliver added value to its client organisation, it has to know 1) which CRE aspects influence its employees, processes, machinery, visitors, etc, 2) how these aspects influence performance and 3) how to measure and manage them. Analysis of

  9. PECULIARITIES OF PERFORMANCE MEASUREMENT IN SOVEREIGN WEALTH FUNDS

    Directory of Open Access Journals (Sweden)

    M. Onopko

    2014-01-01

    Full Text Available Sovereign wealth funds as the subjects of economic relations are analyzed and the main approaches to the assessment of their activities are discussed. The dependence of the performance measurement system and the strategic objectives of the funds and economic policy objectives of the government is indicated.

  10. Performance measurement system for training simulators. Interim report

    International Nuclear Information System (INIS)

    Bockhold, G. Jr.; Roth, D.R.

    1978-05-01

    In the first project phase, the project team has designed, installed, and test run on the Browns Ferry nuclear power plant training simulator a performance measurement system capable of automatic recording of statistical information on operator actions and plant response. Key plant variables and operator actions were monitored and analyzed by the simulator computer for a selected set of four operating and casualty drills. The project has the following objectives: (1) To provide an empirical data base for statistical analysis of operator reliability and for allocation of safety and control functions between operators and automated controls; (2) To develop a method for evaluation of the effectiveness of control room designs and operating procedures; and (3) To develop a system for scoring aspects of operator performance to assist in training evaluations and to support operator selection research. The performance measurement system has shown potential for meeting the research objectives. However, the cost of training simulator time is high; to keep research program costs reasonable, the measurement system is being designed to be an integral part of operator training programs. In the pilot implementation, participating instructors judged the measurement system to be a valuable and objective extension of their abilities to monitor trainee performance

  11. Performance Measures of Academic Faculty--A Case Study

    Science.gov (United States)

    Davidovitch, Nitza; Soen, Dan; Sinuani-Stern, Zila

    2011-01-01

    This case study is the first to track the method used by an Israeli institution of higher education to assess and reward faculty members using a set of performance measures ("Excellence criteria"). The study profiles faculty members who received financial rewards for excellence during 2005-2007, based on the previous year's activities,…

  12. Individual match approach to Bowling performance measures in ...

    African Journals Online (AJOL)

    Match conditions can play a significant role in player performances in a cricket match. If the pitch is in a good condition, the batsmen can achieve good scores, making it difficult for the bowlers. In the case of an uneven pitch or adverse weather conditions, the bowlers may have the upper hand. In order to measure bowlers' ...

  13. Two Measures for Enhancing Data Association Performance in SLAM

    Directory of Open Access Journals (Sweden)

    Wu Zhou

    2014-01-01

    Full Text Available Data association is one of the key problems in the SLAM community. Several data association failures may cause the SLAM results to be divergent. Data association performance in SLAM is affected by both data association methods and sensor information. Two measures of handling sensor information are introduced herein to enhance data association performance in SLAM. For the first measure, truncating strategy of limited features, instead of all matched features, is used for observation update. These features are selected according to an information variable. This truncating strategy is used to lower the effect of false matched features. For the other measure, a special rejecting mechanism is designed to reject suspected observations. When the predicted robot pose is obviously different from the updated robot pose, all observed sensor information at this moment is discarded. The rejecting mechanism aims at eliminating accidental sensor information. Experimental results indicate that the introduced measures perform well in improving the stability of data association in SLAM. These measures are of extraordinary value for real SLAM applications.

  14. Sampling Approaches for Multi-Domain Internet Performance Measurement Infrastructures

    Energy Technology Data Exchange (ETDEWEB)

    Calyam, Prasad

    2014-09-15

    The next-generation of high-performance networks being developed in DOE communities are critical for supporting current and emerging data-intensive science applications. The goal of this project is to investigate multi-domain network status sampling techniques and tools to measure/analyze performance, and thereby provide “network awareness” to end-users and network operators in DOE communities. We leverage the infrastructure and datasets available through perfSONAR, which is a multi-domain measurement framework that has been widely deployed in high-performance computing and networking communities; the DOE community is a core developer and the largest adopter of perfSONAR. Our investigations include development of semantic scheduling algorithms, measurement federation policies, and tools to sample multi-domain and multi-layer network status within perfSONAR deployments. We validate our algorithms and policies with end-to-end measurement analysis tools for various monitoring objectives such as network weather forecasting, anomaly detection, and fault-diagnosis. In addition, we develop a multi-domain architecture for an enterprise-specific perfSONAR deployment that can implement monitoring-objective based sampling and that adheres to any domain-specific measurement policies.

  15. Contracts, Performance Measurement and Accountability in the Public Sector

    DEFF Research Database (Denmark)

    Drewry, Gavin; Greve, Carsten; Tanquerel, Thierry

    This book addresses issues to do with public accountability, audit and performance measurement that are both highly topical and of crucial importance to the theory and practice of public administration in an era of contractualized public management. The literature on public sector contracting...... of audit and accountability in a variety of countries and contexts; the third part offers some wider, cross-cutting perspectives. Based on the work of the EGPA permanent study group on the history of contractualization, Contracts, Performance Measurement and Accountability in the Public Sector draws upon...... - covering both 'hard' agreements (ones that are legally enforceable) and 'soft' agreements (enforced by negotiation and mutual trust) - has been growing for some time and the present book adds a primarily European perspective on contracting, performance-based management and accountability. One important...

  16. A performance measurement using balanced scorecard and structural equation modeling

    Directory of Open Access Journals (Sweden)

    Rosha Makvandi

    2014-02-01

    Full Text Available During the past few years, balanced scorecard (BSC has been widely used as a promising method for performance measurement. BSC studies organizations in terms of four perspectives including customer, internal processes, learning and growth and financial figures. This paper presents a hybrid of BSC and structural equation modeling (SEM to measure the performance of an Iranian university in province of Alborz, Iran. The proposed study of this paper uses this conceptual method, designs a questionnaire and distributes it among some university students and professors. Using SEM technique, the survey analyzes the data and the results indicate that the university did poorly in terms of all four perspectives. The survey extracts necessary target improvement by presenting necessary attributes for performance improvement.

  17. Standardization of test conditions for gamma camera performance measurement

    International Nuclear Information System (INIS)

    Jordan, K.

    1980-01-01

    The actual way of measuring gamma camera performance is to use point sources or flood sources in air, often in combination with bar phantoms. This method mostly brings best performance parameters for cameras but it has nothing in common with the use of a camera in clinical practice. Particular in the case of low energy emitters, like Tc-99m, the influence of scattered radiation over the performance of cameras is very high. Therefore it is important to have test conditions of radionuclide imaging devices, that will approach as best as practicable the measuring conditions in clinical applications. It is therefore a good news that the International Electrochemical Commission IEC has prepared a draft 'Characteristics and test conditions of radionuclide imaging devices' which is now submitted to the national committees for formal approval under the Six Months' Rule. Some essential points of this document are discussed in the paper. (orig.) [de

  18. Building and measuring a high performance network architecture

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, William T.C.; Toole, Timothy; Fisher, Chuck; Dugan, Jon; Wheeler, David; Wing, William R; Nickless, William; Goddard, Gregory; Corbato, Steven; Love, E. Paul; Daspit, Paul; Edwards, Hal; Mercer, Linden; Koester, David; Decina, Basil; Dart, Eli; Paul Reisinger, Paul; Kurihara, Riki; Zekauskas, Matthew J; Plesset, Eric; Wulf, Julie; Luce, Douglas; Rogers, James; Duncan, Rex; Mauth, Jeffery

    2001-04-20

    Once a year, the SC conferences present a unique opportunity to create and build one of the most complex and highest performance networks in the world. At SC2000, large-scale and complex local and wide area networking connections were demonstrated, including large-scale distributed applications running on different architectures. This project was designed to use the unique opportunity presented at SC2000 to create a testbed network environment and then use that network to demonstrate and evaluate high performance computational and communication applications. This testbed was designed to incorporate many interoperable systems and services and was designed for measurement from the very beginning. The end results were key insights into how to use novel, high performance networking technologies and to accumulate measurements that will give insights into the networks of the future.

  19. The merit of cogeneration: Measuring and rewarding performance

    International Nuclear Information System (INIS)

    Verbruggen, Aviel

    2008-01-01

    Cogeneration or combined heat and power (CHP) is a thermal power generation cycle with the merit of recovering part or all of the heat that is fatally discarded by such cycles. This merit of higher efficiency is subject of rewarding by public authorities. When the EU enacts CHP promotion in a Directive (1997-2004), crucial measurement and qualification issues remain unsolved. CEN (coordinator of the European Bureaus of Standards) contributes in clarifying the measurement of CHP activities, but shortfalls remain, while CEN bypasses the debate on qualifying CHP performance. This article offers appropriate methods for measuring CHP activities based on design characteristics of the plants. The co-generated electric output is a necessary and sufficient indicator of CHP merit and performance. Regulators can extend this indicator, but should avoid the perverse effects of biased external benchmarking as the EU Directive entails

  20. Proposed system for measuring project performance using process-based key performance indicators

    NARCIS (Netherlands)

    Haponava, T.; Al-Jibouri, Saad H.S.

    2012-01-01

    Despite some evidence of its usefulness, performance measurement by using Key Performance Indicators (KPIs) in the construction industry also has its critics. Among the shortcomings attributed to existing KPIs is the fact that almost all of them are product oriented. This means that the indicators

  1. The Curvilinear Association between Performance Measurement System Design and Strategic Performance

    DEFF Research Database (Denmark)

    Schneider, Melanie L.; Mahlendorf, Matthias D.; Schäffer, Utz

    This paper reconciles prior research regarding beneficial and detrimental effects of performance measurement system (PMS) design on performance by arguing for a curvilinear association. By taking the too-much-of-a-good-thing effect as a starting point, we challenge the assumption of a linear...

  2. Strategic performance management: development of a performance measurement system at the Mayo Clinic.

    Science.gov (United States)

    Curtright, J W; Stolp-Smith, S C; Edell, E S

    2000-01-01

    Managing and measuring performance become exceedingly complex as healthcare institutions evolve into integrated health systems comprised of hospitals, outpatient clinics and surgery centers, nursing homes, and home health services. Leaders of integrated health systems need to develop a methodology and system that align organizational strategies with performance measurement and management. To meet this end, multiple healthcare organizations embrace the performance-indicators reporting system known as a "balanced scorecard" or a "dashboard report." This discrete set of macrolevel indicators gives senior management a fast but comprehensive glimpse of the organization's performance in meeting its quality, operational, and financial goals. The leadership of outpatient operations for Mayo Clinic in Rochester, Minnesota built on this concept by creating a performance management and measurement system that monitors and reports how well the organization achieves its performance goals. Internal stakeholders identified metrics to measure performance in each key category. Through these metrics, the organization links Mayo Clinic's vision, primary value, core principles, and day-to-day operations by monitoring key performance indicators on a weekly, monthly, or quarterly basis.

  3. Measured Performance of a Varied Airflow Small-Diameter Duct System

    Energy Technology Data Exchange (ETDEWEB)

    Poerschke, Andrew [IBACOS, Inc., Pittsburgh, PA (United States)

    2017-03-01

    This study tests the performance of a variable airflow small-diameter duct heating, ventilation, and air conditioning (HVAC) system in a new construction unoccupied low-load test house in Pittsburgh, Pennsylvania. The duct system was installed entirely in conditioned space and was operated from the winter through summer seasons. Measurements were collected on the in-room temperatures and energy consumed by the air handler and heat pump unit. Operation modes with three different volumes of airflow were compared to determine the ideal airflow scenario that maximizes room-to-room thermal uniformity while minimizing fan energy consumption. Black felt infrared imagery was used as a measure of diffuser throw and in-room air mixing. Measured results indicate the small-diameter, high velocity airflow system can provide comfort under some conditions. Solar heat gains resulted in southern rooms drifting beyond acceptable temperature limits. Insufficient airflow to some bedrooms also resulted in periods of potential discomfort. Homebuilders or HVAC contractors can use these results to assess whether this space conditioning strategy is an attractive alternative to a traditional duct system. The team performed a cost analysis of two duct system configurations: (1) a conventional diameter and velocity duct system, and (2) the small-diameter duct system. This work applies to both new and retrofit homes that have achieved a low heating and cooling density either by energy conservation or by operation in a mild climate with few heating or cooling degree days. Guidance is provided on cost trade-offs between the conventional duct system and the small-diameter duct system.

  4. Measured Performance of a Varied Airflow Small-Diameter Duct System

    Energy Technology Data Exchange (ETDEWEB)

    Poerschke, Andrew [IBACOS, Inc., Pittsburgh, PA (United States)

    2017-03-16

    This study tests the performance of a variable airflow small-diameter duct heating, ventilation, and air conditioning (HVAC) system in a new construction unoccupied low-load test house in Pittsburgh, Pennsylvania. The duct system was installed entirely in conditioned space and was operated from the winter through summer seasons. Measurements were collected on the in-room temperatures and energy consumed by the air handler and heat pump unit. Operation modes with three different volumes of airflow were compared to determine the ideal airflow scenario that maximizes room-to-room thermal uniformity while minimizing fan energy consumption. Black felt infrared imagery was used as a measure of diffuser throw and in-room air mixing. Measured results indicate the small-diameter, high velocity airflow system can provide comfort under some conditions. Solar heat gains resulted in southern rooms drifting beyond acceptable temperature limits. Insufficient airflow to some bedrooms also resulted in periods of potential discomfort. Homebuilders or HVAC contractors can use these results to assess whether this space conditioning strategy is an attractive alternative to a traditional duct system. The team performed a cost analysis of two duct system configurations: (1) a conventional diameter and velocity duct system, and (2) the small-diameter duct system. This work applies to both new and retrofit homes that have achieved a low heating and cooling density either by energy conservation or by operation in a mild climate with few heating or cooling degree days. Guidance is provided on cost trade-offs between the conventional duct system and the small-diameter duct system.

  5. Measured Performance of a Low Temperature Air Source Heat Pump

    Energy Technology Data Exchange (ETDEWEB)

    R.K. Johnson

    2013-09-01

    A 4-ton Low Temperature Heat Pump (LTHP) manufactured by Hallowell International was installed in a residence near New Haven, Connecticut and monitored over two winters of operation. After attending to some significant service issues, the heat pump operated as designed. This report should be considered a review of the dual compressor “boosted heat pump” technology. The Low Temperature Heat Pump system operates with four increasing levels of capacity (heat output) as the outdoor temperature drops.

  6. PERFORMANCE MEASUREMENT OF UCITS INVESTMENT FUNDS IN CROATIA

    Directory of Open Access Journals (Sweden)

    Marko Curkovic

    2017-03-01

    Full Text Available UCITS investment funds represent an important investment opportunity for retail, as well for institutional investors in the European Union. The aim of this paper is to analyse the performance of the UCITS investment funds in Croatia and to detect relatively homogeneous groups among the UCITS funds based on its performance. The analysis includes 55 UCITS, in the period from the beginning of 2011 until the end of 2014, and it is conducted on daily data of share prices, available from Bloomberg terminal. Analysis is performed separately within the groups of different investment fund by investment strategy. The research methodology is based on the calculation of various indicators of absolute and relative risk-adjusted performance and riskiness of the funds. In general, based on analysis of performance measures, it can be concluded that funds with higher values of net assets were more successful compared to the funds with below-average asset values. Also, funds with below-average values of net assets were more volatile. At the same time, funds run by foreign own management companies were more successful by the absolute performance measures, compared to funds run by management companies with domestic ownership. On the other hand, those funds were more volatile, as well.

  7. THE PERFORMANCE OF THE ECONOMIC ENTITY MEASURED THROUGH ACCOUNTING INFORMATION

    Directory of Open Access Journals (Sweden)

    Marius Cristian Milos

    2012-01-01

    Full Text Available The users of financial statements need information regarding the resources of an economic entity and also data regarding the way in which the entity’s management is using resources. This information helps users to quantify efficiency and performance within an entity. There are many stakeholders who do show interest in an entity’s financial reports, including existing and potential investors, employees, lenders, suppliers, customers, regulators and other government agencies and not the least the common citizens. The main purpose of this paper is to highlight the importance of the performance measurement and to discuss possible reporting methods. Performance is a concept that raises many questions regarding the most accurate way or the best method for quantifying and reporting performance at the company level .So if financial performance indicators are considered to offer an accurate image of the situation of a company, the modern approach which focuses also on non-financial indicators offers new perspectives upon performance measurement, which may be really expressive and also based on simplicity.

  8. Joint Macro and Femto Field Performance and Interference Measurements

    DEFF Research Database (Denmark)

    Jørgensen, Niels T.K.; Isotalo, Tero; Pedersen, Klaus

    2012-01-01

    In this paper macro performance in a co-channel macro and femto setup is studied. Measurements are performed in a live Universal Mobile Telecommunication System (UMTS) network. It is concluded that femto interference does not affect macro downlink (DL) performance as long as the macro Received Si...... radius smaller than 5 meter – with realistic power settings. This makes co-channel femto deployment less promising in dense macro environments with good macro RSCP coverage.......In this paper macro performance in a co-channel macro and femto setup is studied. Measurements are performed in a live Universal Mobile Telecommunication System (UMTS) network. It is concluded that femto interference does not affect macro downlink (DL) performance as long as the macro Received...... Signal Code Power (RSCP) is stronger than femto RSCP. We also conclude that a macro escape carrier is a robust DL interference management solution. In uplink (UL) direction it is shown that a single femto UE close to macro cell potentially can cause a noise rise of 6 dB in the surrounding macro cell...

  9. The impact of multi-criteria performance measurement on business performance improvement

    OpenAIRE

    Kasie, Fentahun Moges; Belay, Alemu Moges

    2013-01-01

    Purpose: The purpose of this paper is to investigate the relationship between multi-criteria performance measurement (MCPM) practice and business performance improvement using the raw data collected from 33 selected manufacturing companies. In addition, it proposes modified MCPM model as an effective approach to improve business performance of manufacturing companies. Design/methodology/approach:Research paper. Primary and secondary data were collected using questionnaire survey, interview an...

  10. Performance Measurement using KPKU- BUMN in X School Education Foundation

    Science.gov (United States)

    Arijanto, Sugih; Harsono, Ambar; Taroepratjeka, Harsono

    2016-01-01

    The purpose of this research is to determine X School's Strengths and Opportunity of Improvement through performance measurement using KPKU-BUMN (Kriteria Penilaian Kinerja Unggul - Kementerian Badan Usaha Milik Negara). KPKU-BUMN is developed based on Malcolm Baldrige Criteria for Performance Excellent (MBCfPE). X school is an education foundation at Bandung that has provides education from kindergarten, elementary school, to junior and senior high school. The measurement is implemented by two aspects, Process and Result. The Process is measured by A-D-L-I approaches (Approach- Deployment-Learning- Integration), on the other hand The Result is measured by Le-T-C-I approach (Level-Trend- Comparison-Integration). There are six processes that will be measured: (1) Leadership, (2) Strategic Planning, (3) Customer Focus, (4) Measurement, Analysis and Knowledge Management, (5) Work Force Focus, and (6) Operation Focus. Meanwhile, the result are (a) product & process outcomes, (b) customer-focused outcomes, (c) workforce-focused outcomes, (d) leadership & governance outcomes, and (e) financial & market outcomes. The overall score for X School is 284/1000, which means X School is at “early result” level at “poor” global image.

  11. Measuring the performance of visual to auditory information conversion.

    Directory of Open Access Journals (Sweden)

    Shern Shiou Tan

    Full Text Available BACKGROUND: Visual to auditory conversion systems have been in existence for several decades. Besides being among the front runners in providing visual capabilities to blind users, the auditory cues generated from image sonification systems are still easier to learn and adapt to compared to other similar techniques. Other advantages include low cost, easy customizability, and universality. However, every system developed so far has its own set of strengths and weaknesses. In order to improve these systems further, we propose an automated and quantitative method to measure the performance of such systems. With these quantitative measurements, it is possible to gauge the relative strengths and weaknesses of different systems and rank the systems accordingly. METHODOLOGY: Performance is measured by both the interpretability and also the information preservation of visual to auditory conversions. Interpretability is measured by computing the correlation of inter image distance (IID and inter sound distance (ISD whereas the information preservation is computed by applying Information Theory to measure the entropy of both visual and corresponding auditory signals. These measurements provide a basis and some insights on how the systems work. CONCLUSIONS: With an automated interpretability measure as a standard, more image sonification systems can be developed, compared, and then improved. Even though the measure does not test systems as thoroughly as carefully designed psychological experiments, a quantitative measurement like the one proposed here can compare systems to a certain degree without incurring much cost. Underlying this research is the hope that a major breakthrough in image sonification systems will allow blind users to cost effectively regain enough visual functions to allow them to lead secure and productive lives.

  12. Measurement properties of continuous text reading performance tests.

    Science.gov (United States)

    Brussee, Tamara; van Nispen, Ruth M A; van Rens, Ger H M B

    2014-11-01

    Measurement properties of tests to assess reading acuity or reading performance have not been extensively evaluated. This study aims to provide an overview of the literature on available continuous text reading tests and their measurement properties. A literature search was performed in PubMed, Embase and PsycInfo. Subsequently, information on design and content of reading tests, study design and measurement properties were extracted using consensus-based standards for selection of health measurement instruments. Quality of studies, reading tests and measurement properties were systematically assessed using pre-specified criteria. From 2334 identified articles, 20 relevant articles were found on measurement properties of three reading tests in various languages: IReST, MNread Reading Test and Radner Reading Charts. All three reading tests scored high on content validity. Reproducibility studies (repeated measurements between different testing sessions) of the IReST and MNread of commercially available reading tests in different languages were missing. The IReST scored best on inter-language comparison, the MNread scored well in repeatability studies (repeated measurements under the same conditions) and the Radner showed good reproducibility in studies. Although in daily practice there are other continuous text reading tests available meeting the criteria of this review, measurement properties were described in scientific studies for only three of them. Of the few available studies, the quality and content of study design and methodology used varied. For testing existing reading tests and the development of new ones, for example in other languages, we make several recommendations, including careful description of patient characteristics, use of objective and subjective lighting levels, good control of working distance, documentation of the number of raters and their training, careful documentation of scoring rules and the use of Bland-Altman analyses or similar for

  13. Impact of Climate Change Adaptation Strategies on Winter Wheat and Cropping System Performance across Precipitation Gradients in the Inland Pacific Northwest, USA

    Directory of Open Access Journals (Sweden)

    Tai M. Maaz

    2017-05-01

    Full Text Available Ecological instability and low resource use efficiencies are concerns for the long-term productivity of conventional cereal monoculture systems, particularly those threatened by projected climate change. Crop intensification, diversification, reduced tillage, and variable N management are among strategies proposed to mitigate and adapt to climate shifts in the inland Pacific Northwest (iPNW. Our objectives were to assess these strategies across iPNW agroecological zones and time for their impacts on (1 winter wheat (WW (Triticum aestivum L. productivity, (2 crop sequence productivity, and (3 N fertilizer use efficiency. Region-wide analysis indicated that WW yields increased with increasing annual precipitation, prior to maximizing at 520 mm yr−1 and subsequently declining when annual precipitation was not adjusted for available soil water holding capacity. While fallow periods were effective at mitigating low nitrogen (N fertilization efficiencies under low precipitation, efficiencies declined as annual precipitation exceeded 500 mm yr−1. Variability in the response of WW yields to annual precipitation and N fertilization among locations and within sites supports precision N management implementation across the region. In years receiving <350 mm precipitation yr−1, WW yields declined when preceded by crops rather than summer fallow. Nevertheless, WW yields were greater when preceded by pulses and oilseeds rather than wheat across a range of yield potentials, and when under conservation tillage practices at low yield potentials. Despite the yield penalty associated with eliminating fallow prior to WW, cropping system level productivity was not affected by intensification, diversification, or conservation tillage. However, increased fertilizer N inputs, lower fertilizer N use efficiencies, and more yield variance may offset and limit the economic feasibility of intensified and diversified cropping systems.

  14. Development of measurement standards for verifying functional performance of surface texture measuring instruments

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, A [Life and Industrial Product Development Department Olympus Corporation, 2951 Ishikawa-machi, Hachiouji-shi, Tokyo (Japan); Suzuki, H [Industrial Marketing and Planning Department Olympus Corporation, Shinjyuku Monolith, 3-1 Nishi-Shinjyuku 2-chome, Tokyo (Japan); Yanagi, K, E-mail: a_fujii@ot.olympus.co.jp [Department of Mechanical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka-machi, Nagaoka-shi, Niigata (Japan)

    2011-08-19

    A new measurement standard is proposed for verifying overall functional performance of surface texture measuring instruments. Its surface is composed of sinusoidal surface waveforms of chirp signals along horizontal cross sections of the material measure. One of the notable features is that the amplitude of each cycle in the chirp signal form is geometrically modulated so that the maximum slope is kept constant. The maximum slope of the chirp-like signal is gradually decreased according to movement in the lateral direction. We fabricated the measurement standard by FIB processing, and it was calibrated by AFM. We tried to evaluate the functional performance of Laser Scanning Microscope by this standard in terms of amplitude response with varying slope angles. As a result, it was concluded that the proposed standard can easily evaluate the performance of surface texture measuring instruments.

  15. Measuring process performance within healthcare logistics - a decision tool for selecting measuring technologies

    DEFF Research Database (Denmark)

    Feibert, Diana Cordes; Jacobsen, Peter

    2015-01-01

    Performance measurement can support the organization in improving the efficiency and effectiveness of logistical healthcare processes. Selecting the most suitable technologies is important to ensure data validity. A case study of the hospital cleaning process at a public Danish hospital...... was conducted. Monitoring tasks and ascertaining quality of work is difficult in such a process. Based on principal-agent theory, a set of decision indicator has been developed, and a decision framework for assessing technologies to enable performance measurement has been proposed....

  16. Field significance of performance measures in the context of regional climate model evaluation. Part 1: temperature

    Science.gov (United States)

    Ivanov, Martin; Warrach-Sagi, Kirsten; Wulfmeyer, Volker

    2018-04-01

    A new approach for rigorous spatial analysis of the downscaling performance of regional climate model (RCM) simulations is introduced. It is based on a multiple comparison of the local tests at the grid cells and is also known as "field" or "global" significance. New performance measures for estimating the added value of downscaled data relative to the large-scale forcing fields are developed. The methodology is exemplarily applied to a standard EURO-CORDEX hindcast simulation with the Weather Research and Forecasting (WRF) model coupled with the land surface model NOAH at 0.11 ∘ grid resolution. Monthly temperature climatology for the 1990-2009 period is analysed for Germany for winter and summer in comparison with high-resolution gridded observations from the German Weather Service. The field significance test controls the proportion of falsely rejected local tests in a meaningful way and is robust to spatial dependence. Hence, the spatial patterns of the statistically significant local tests are also meaningful. We interpret them from a process-oriented perspective. In winter and in most regions in summer, the downscaled distributions are statistically indistinguishable from the observed ones. A systematic cold summer bias occurs in deep river valleys due to overestimated elevations, in coastal areas due probably to enhanced sea breeze circulation, and over large lakes due to the interpolation of water temperatures. Urban areas in concave topography forms have a warm summer bias due to the strong heat islands, not reflected in the observations. WRF-NOAH generates appropriate fine-scale features in the monthly temperature field over regions of complex topography, but over spatially homogeneous areas even small biases can lead to significant deteriorations relative to the driving reanalysis. As the added value of global climate model (GCM)-driven simulations cannot be smaller than this perfect-boundary estimate, this work demonstrates in a rigorous manner the

  17. Thermal performance measurements on ultimate heat sinks--cooling ponds

    International Nuclear Information System (INIS)

    Hadlock, R.K.; Abbey, O.B.

    1977-12-01

    The primary objective of the studies described is to obtain the requisite data, with respect to modeling requirements, to characterize thermal performance of heat sinks for nuclear facilities existing at elevated water temperatures in result of experiencing a genuinely large heat load and responding to meteorological influence. The data should reflect thermal performance for combinations leading to worst-case meteorological influence. A geothermal water retention basin has been chosen as the site for the first measurement program and data have been obtained in the first of several experiments scheduled to be performed there. These data illustrate the thermal and water budgets during episodes of cooling from an initially high pond water bulk temperature. Monitoring proceeded while the pond experienced only meteorological and seepage influence. The data are discussed and are presented as a data volume which may be used for calculation purposes. Suggestions for future measurement programs are stated with the intent to maintain and improve relevance to nuclear ultimate heat sinks while continuing to examine the performance of the analog geothermal pond. It is further suggested that the geothermal pond, with some modification, may be a suitable site for spray pond measurements

  18. Measuring recent research performance for Chinese universities using bibliometric methods

    KAUST Repository

    Zhu, Jia

    2014-07-29

    This paper focuses on measuring the academic research performance of Chinese universities by using Scopus database from 2007 to 2010. We have provided meaningful indicators to measure the research performance of Chinese universities as compared to world class universities of the US and the European region. Using these indicators, we first measure the quantity and quality of the research outcomes of the universities and then examine the internationalization of research by using international collaborations, international citations and international impact metrics. Using all of this data, we finally present an overall score called research performance point to measure the comprehensive research strength of the universities for the selected subject categories. The comparison identifies the gap between Chinese universities and top-tier universities from selected regions across various subject areas. We find that Chinese universities are doing well in terms of publication volume but receive less citations from their published work. We also find that the Chinese universities have relative low percentage of publications at high impact venues, which may be the reason that they are not receiving more citations. Therefore, a careful selection of publication venues may help the Chinese universities to compete with world class universities and increase their research internationalization. © 2014 Akadémiai Kiadó, Budapest, Hungary.

  19. Continuous measurements at the urban roadside in an Asian megacity by Aerosol Chemical Speciation Monitor (ACSM): particulate matter characteristics during fall and winter seasons in Hong Kong

    Science.gov (United States)

    Sun, C.; Lee, B. P.; Huang, D.; Jie Li, Y.; Schurman, M. I.; Louie, P. K. K.; Luk, C.; Chan, C. K.

    2016-02-01

    Non-refractory submicron aerosol is characterized using an Aerosol Chemical Speciation Monitor (ACSM) in the fall and winter seasons of 2013 on the roadside in an Asian megacity environment in Hong Kong. Organic aerosol (OA), characterized by application of Positive Matrix Factorization (PMF), and sulfate are found to be dominant. Traffic-related organic aerosol shows good correlation with other vehicle-related species, and cooking aerosol displays clear mealtime concentration maxima and association with surface winds from restaurant areas. Contributions of individual species and OA factors to high NR-PM1 are analyzed for hourly data and daily data; while cooking emissions in OA contribute to high hourly concentrations, particularly during mealtimes, secondary organic aerosol components are responsible for episodic events and high day-to-day PM concentrations. Clean periods are either associated with precipitation, which reduces secondary OA with a lesser impact on primary organics, or clean oceanic air masses with reduced long-range transport and better dilution of local pollution. Haze events are connected with increases in contribution of secondary organic aerosol, from 30 to 50 % among total non-refractory organics, and the influence of continental air masses.

  20. Continuous measurements at the urban roadside in an Asian megacity by Aerosol Chemical Speciation Monitor (ACSM: particulate matter characteristics during fall and winter seasons in Hong Kong

    Directory of Open Access Journals (Sweden)

    C. Sun

    2016-02-01

    Full Text Available Non-refractory submicron aerosol is characterized using an Aerosol Chemical Speciation Monitor (ACSM in the fall and winter seasons of 2013 on the roadside in an Asian megacity environment in Hong Kong. Organic aerosol (OA, characterized by application of Positive Matrix Factorization (PMF, and sulfate are found to be dominant. Traffic-related organic aerosol shows good correlation with other vehicle-related species, and cooking aerosol displays clear mealtime concentration maxima and association with surface winds from restaurant areas. Contributions of individual species and OA factors to high NR-PM1 are analyzed for hourly data and daily data; while cooking emissions in OA contribute to high hourly concentrations, particularly during mealtimes, secondary organic aerosol components are responsible for episodic events and high day-to-day PM concentrations. Clean periods are either associated with precipitation, which reduces secondary OA with a lesser impact on primary organics, or clean oceanic air masses with reduced long-range transport and better dilution of local pollution. Haze events are connected with increases in contribution of secondary organic aerosol, from 30 to 50 % among total non-refractory organics, and the influence of continental air masses.

  1. TRACEABILITY OF PRECISION MEASUREMENTS ON COORDINATE MEASURING MACHINES – PERFORMANCE VERIFICATION OF CMMs

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo; Sobiecki, René; Tosello, Guido

    This document is used in connection with one exercise of 30 minutes duration as a part of the course VISION ONLINE – One week course on Precision & Nanometrology. The exercise concerns performance verification of the volumetric measuring capability of a small volume coordinate measuring machine...

  2. Measuring cognitive load: performance, mental effort and simulation task complexity.

    Science.gov (United States)

    Haji, Faizal A; Rojas, David; Childs, Ruth; de Ribaupierre, Sandrine; Dubrowski, Adam

    2015-08-01

    Interest in applying cognitive load theory in health care simulation is growing. This line of inquiry requires measures that are sensitive to changes in cognitive load arising from different instructional designs. Recently, mental effort ratings and secondary task performance have shown promise as measures of cognitive load in health care simulation. We investigate the sensitivity of these measures to predicted differences in intrinsic load arising from variations in task complexity and learner expertise during simulation-based surgical skills training. We randomly assigned 28 novice medical students to simulation training on a simple or complex surgical knot-tying task. Participants completed 13 practice trials, interspersed with computer-based video instruction. On trials 1, 5, 9 and 13, knot-tying performance was assessed using time and movement efficiency measures, and cognitive load was assessed using subjective rating of mental effort (SRME) and simple reaction time (SRT) on a vibrotactile stimulus-monitoring secondary task. Significant improvements in knot-tying performance (F(1.04,24.95)  = 41.1, p cognitive load (F(2.3,58.5)  = 57.7, p load among novices engaged in simulation-based learning. These measures can be used to track cognitive load during skills training. Mental effort ratings are also sensitive to small differences in intrinsic load arising from variations in the physical complexity of a simulation task. The complementary nature of these subjective and objective measures suggests their combined use is advantageous in simulation instructional design research. © 2015 John Wiley & Sons Ltd.

  3. A Thermographic Measurement Approach to Assess Supercapacitor Electrical Performances

    Directory of Open Access Journals (Sweden)

    Stanislaw Galla

    2017-12-01

    Full Text Available This paper describes a proposal for the qualitative assessment of condition of supercapacitors based on the conducted thermographic measurements. The presented measurement stand was accompanied by the concept of methodology of performing tests. Necessary conditions, which were needed to minimize the influence of disturbing factors on the performance of thermal imaging measurements, were also indicated. Mentioned factors resulted from both: the hardware limitations and from the necessity to prepare samples. The algorithm that was used to determine the basic parameters for assessment has been presented. The article suggests to use additional factors that may facilitate the analysis of obtained results. Measuring the usefulness of the proposed methodology was tested on commercial samples of supercapacitors. All of the tests were taken in conjunction with the classical methods based on capacitance (C and equivalent series resistance (ESR measurements, which were also presented in the paper. Selected results presenting the observed changes occurring in both: basic parameters of supercapacitors and accompanying fluctuations of thermal fields, along with analysis, were shown. The observed limitations of the proposed assessment method and the suggestions for its development were also described.

  4. Process-oriented performance indicators for measuring ecodesign management practices

    DEFF Research Database (Denmark)

    Rodrigues, Vinicius Picanco; Pigosso, Daniela Cristina Antelmi; McAloone, Tim C.

    2016-01-01

    In order to support ecodesign performance measurement from a business perspective, this paper performs an exploration of available process-oriented indicators to be applied to ecodesign management practices. With the Ecodesign Maturity Model as a background framework, a systematic literature review...... coupled with a cross-content analysis was carried out to assign proper indicators to the practices. Results show that the currently available indicators do not fully reflect the characteristics of ecodesign and there is significant room for improving the development of tailor-made indicators....

  5. Optimisation of key performance measures in air cargo demand management

    OpenAIRE

    Alexander May; Adrian Anslow; Udechukwu Ojiako; Yue Wu; Alasdair Marshall; Maxwell Chipulu

    2014-01-01

    This article sought to facilitate the optimisation of key performance measures utilised for demand management in air cargo operations. The focus was on the Revenue Management team at Virgin Atlantic Cargo and a fuzzy group decision-making method was used. Utilising intelligent fuzzy multi-criteria methods, the authors generated a ranking order of ten key outcome-based performance indicators for Virgin Atlantic air cargo Revenue Management. The result of this industry-driven study showed that ...

  6. Desempenho da cultura do feijão após diferentes formas de uso do solo no inverno Performance of common bean cultivated after different soil use during the winter

    Directory of Open Access Journals (Sweden)

    Alvadi Antonio Balbinot Junior

    2009-11-01

    Full Text Available O uso e manejo do solo durante o inverno pode alterar as características físicas do solo, a cobertura remanescente e o desempenho da cultura semeada em sucessão. O objetivo deste trabalho foi avaliar o efeito de formas de uso do solo no inverno sobre essas variáveis, semeando-se a cultura do feijão em sucessão, manejada em plantio direto. Na safra 2007/08, foram conduzidos três experimentos na região do Planalto Norte Catarinense, onde foram avaliadas cinco formas de uso do solo durante o inverno: 1 consórcio de aveia preta + azevém + ervilhaca + trevo vesiculoso manejado sem pastejo e sem adubação nitrogenada (consórcio cobertura; 2 o mesmo consórcio, com pastejo e com 100kg ha-1 de N em cobertura (pastagem com N; 3 o mesmo consórcio, com pastejo e sem adubação nitrogenada (pastagem sem N; 4 nabo forrageiro, sem pastejo e sem adubação nitrogenada (nabo forrageiro; e 5 pousio, sem pastejo e sem adubação nitrogenada (pousio. O consórcio cobertura proporciona maior quantidade de palha para o cultivo de feijão em sucessão, mas as formas de uso do solo no inverno estudadas não afetam expressivamente a densidade e a macroporosidade do solo. O uso do solo no inverno com pastagem anual em sistema integração lavoura-pecuária, coberturas de solo e pousio não afeta o desempenho da cultura do feijão semeada em sucessão, manejada em plantio direto.Soil use and management during the winter can affect soil physical properties, reminiscent straw and performance of the crop cultivated in succession. The objective of this study was to evaluate the effect of winter soil use on these variables, cultivating black bean under no tillage system in the summer. Three experiments were carried out in the North Plateau of Santa Catarina State, Brazil, during 2007/08 crop season, with five strategies of soil use during the winter: 1 multicropping with black oat + ryegrass + commom vetch + arrow leaf clover without grazing and nitrogen

  7. Quantification of the flow measurement performance due to installation changes

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Ana Luisa Auler da Silva [Petrobras Transporte S.A. (TRANSPETRO), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    The objective is to present a criterion to identify and quantify improvements in the performance of flowmeters due to alterations in the design of a measurement system. The method was developed aiming at improvements in the operational systems, but is also useful in custody transfer systems. Take as base the estimate of uncertainty in the measurement systems, and seek a more intuitive way so as to aggregate the experience and knowledge available in the company. The identification of the measurand is carried out based on available information, the processing of data and the method of calculation. The improvements in the installation of measurement systems are given priority based on the measurement uncertainty of the CTPL (temperature and pressure correction factor) and the MF(meter factor). In the case of the CTPL, the influence of the pressure, temperature and density instruments in the results of the measurement system is evaluated, and in the case of the MF, the influence of the calibration system. The possibilities for calibrating the flowmeter in industry are presented, also detailing the calibration of the operational meter against custody transfer systems. The analysis of networks includes calculating the uncertainty in the closing of the network balance, calculation of the uncertainties and contributions of the measurement systems that form part of the network, and a comparison of improvements and costs, calculation for each alteration in the design of the measurement system, and its cost per improvement of 0.01% in the uncertainty of the closing. (author)

  8. Remote Diagnosis of Nitrogen Status in Winter Oilseed Rape

    Science.gov (United States)

    Liu, S.

    2016-12-01

    Winter oilseed rape is one of the most important oilseed crops in the world. Compared with cereal crops, it requires high amount of nitrogen (N) supplies, but it is also characterized by low N use efficiency. The N nutrition index (NNI), defined as the ratio of the actual plant N concentration (PNC) to the critical PNC at a given biomass level, has been widely used to diagnose plant N status and to aid optimizing N fertilization. But traditional techniques to determine NNI in the lab are time-consuming and expensive. Remote sensing provides a promising approach for large-scale and rapid monitoring and diagnosis of crop N status. In this study, we conducted the experiment in the winter oilseed rape field with eight fertilization treatments in the growing season of 2014 and 2015. PNC, dry mass, and canopy spectra were measured during the different growth stages of winter oilseed rape. The N dilution curve was developed with measurements, and NNI was computed and analyzed for different treatments and different growth stage. For the same treatment, NNI decreased as more leaves were developing. Two methods were applied to remotely estimating NNI for winter oilseed rape: (1) NNI was estimated directly with vegetation indices (VIs) derived from canopy spectra; (2) the actual PNC and the critical PNC at the given biomass level were estimated separately with different types of VIs, and NNI was then computed with the two parts of the estimations. We found that VIs based solely on bands in the visible region provided the most accurate estimates of PNC. Estimating NNI directly with VIs had better performance than estimating the actual PNC and the critical PNC separately.

  9. Innovative Performance Measurement: an Integrative Perspective of Stakeholder's View

    Directory of Open Access Journals (Sweden)

    López-Fresno Palmira

    2014-11-01

    Full Text Available Business Process Management (BPM has been increasingly focused as an holistic approach to manage organizations for better organizational effectiveness. BPM involves the use of innovative performance measurement systems to follow up, coordinate, control and improve processes and overall business efficacy and efficiency. In this paper we propose a global holistic perspective of integrated information, combining the view of all stakeholders and both qualitative and quantitative information, as a basic prerequisite for quality of information for better decision making. The paper includes findings from an empirical case study of measuring Parkinson's Disease Neurosurgery process, including stakeholder's view with an integrative perspective.

  10. Influence of Spherical Radiation Pattern Measurement Uncertainty on Handset Performance Measures

    DEFF Research Database (Denmark)

    Nielsen, Jesper Ødum; Pedersen, Gert Frølund

    2005-01-01

    system that may introduce errors in standardized performance measurements. Radiation patterns of six handsets have been measured while they were mounted at various offsets from the reference position defined by the Cellular Telecommunications & Internet Association (CTIA) certification. The change...... in the performance measures are investigated for both the GSM-900 and the GSM-1800 band. Despite the deliberately large deviations from the reference position, the changes in TRP and TIS are generally within ±0.5 dB with a maximum of about 1.4 dB. For the MEG values the results depend on the orientation...

  11. Winter Frost and Fog

    Science.gov (United States)

    2005-01-01

    This somewhat oblique blue wide angle Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows the 174 km (108 mi) diameter crater, Terby, and its vicinity in December 2004. Located north of Hellas, this region can be covered with seasonal frost and ground-hugging fog, even in the afternoon, despite being north of 30oS. The subtle, wavy pattern is a manifestation of fog. Location near: 28oS, 286oW Illumination from: upper left Season: Southern Winter

  12. A measurement-based performability model for a multiprocessor system

    Science.gov (United States)

    Ilsueh, M. C.; Iyer, Ravi K.; Trivedi, K. S.

    1987-01-01

    A measurement-based performability model based on real error-data collected on a multiprocessor system is described. Model development from the raw errror-data to the estimation of cumulative reward is described. Both normal and failure behavior of the system are characterized. The measured data show that the holding times in key operational and failure states are not simple exponential and that semi-Markov process is necessary to model the system behavior. A reward function, based on the service rate and the error rate in each state, is then defined in order to estimate the performability of the system and to depict the cost of different failure types and recovery procedures.

  13. Relating Standardized Visual Perception Measures to Simulator Visual System Performance

    Science.gov (United States)

    Kaiser, Mary K.; Sweet, Barbara T.

    2013-01-01

    Human vision is quantified through the use of standardized clinical vision measurements. These measurements typically include visual acuity (near and far), contrast sensitivity, color vision, stereopsis (a.k.a. stereo acuity), and visual field periphery. Simulator visual system performance is specified in terms such as brightness, contrast, color depth, color gamut, gamma, resolution, and field-of-view. How do these simulator performance characteristics relate to the perceptual experience of the pilot in the simulator? In this paper, visual acuity and contrast sensitivity will be related to simulator visual system resolution, contrast, and dynamic range; similarly, color vision will be related to color depth/color gamut. Finally, we will consider how some characteristics of human vision not typically included in current clinical assessments could be used to better inform simulator requirements (e.g., relating dynamic characteristics of human vision to update rate and other temporal display characteristics).

  14. Interlaboratory analytical performance studies; a way to estimate measurement uncertainty

    Directory of Open Access Journals (Sweden)

    El¿bieta £ysiak-Pastuszak

    2004-09-01

    Full Text Available Comparability of data collected within collaborative programmes became the key challenge of analytical chemistry in the 1990s, including monitoring of the marine environment. To obtain relevant and reliable data, the analytical process has to proceed under a well-established Quality Assurance (QA system with external analytical proficiency tests as an inherent component. A programme called Quality Assurance in Marine Monitoring in Europe (QUASIMEME was established in 1993 and evolved over the years as the major provider of QA proficiency tests for nutrients, trace metals and chlorinated organic compounds in marine environment studies. The article presents an evaluation of results obtained in QUASIMEME Laboratory Performance Studies by the monitoring laboratory of the Institute of Meteorology and Water Management (Gdynia, Poland in exercises on nutrient determination in seawater. The measurement uncertainty estimated from routine internal quality control measurements and from results of analytical performance exercises is also presented in the paper.

  15. Performance and some carcass measurements in starter broiler ...

    African Journals Online (AJOL)

    A 28 day feeding trial was conducted to investigate the performance and some carcass measurements in starter broiler birds fed sweet potato meal. Three hundred and five (305) Anak broilers of one week old were randomly assigned to five treatment diets. Diets 1, 2, 3, 4, and 5 contain 0, 2.5, 5.0, 7.5 and 10.0% levels of ...

  16. Analyze of the Measuring Performance for Artificially Business Intelligent Systems

    OpenAIRE

    Vatuiu, Teodora

    2007-01-01

    This paper analyzes the measuring performance of artificially business intelligent systems. Thousands of persons-years have been devoted to the research and development in the vari¬ous aspects of artificially intelligent systems. Much progress has been attained. However, there has been no means of evaluating the progress of the field. How can we assess the cur¬rent state of the science? Most of business intelligent systems are beginning to be deployed commercially. How can a commercial buyer ...

  17. Accounting for heterogeneity in the measurement of hospital performance

    OpenAIRE

    Philippe K. Widmer; Peter Zweifel; Mehdi Farsi

    2011-01-01

    With prospective payment of hospitals becoming more common, measuring their performance is gaining in importance. However, the standard cost frontier model yields biased efficiency scores because it ignores technological heterogeneity between hospitals. In this paper, efficiency scores are derived from a random intercept and an extended random parameter frontier model, designed to overcome the problem of unobserved heterogeneity in stochastic frontier analysis. Using a sample of 100 Swiss ...

  18. Aims and Formats of performance measurement at Danish Universities

    DEFF Research Database (Denmark)

    Raffnsøe-Møller, Morten

    2011-01-01

    Abstract This article traces the aims and formats of performance measurement of Danish Universities as they originate from the Ministry of Finance’s plan for governance of the public sector. The article further show that the fierce conflicts between central administration and the universities over...... and intelligent regimes – is used to propose a way out of the current governance impasse at the universities....

  19. Winter mortality in relation to climate

    NARCIS (Netherlands)

    Keatinge, W. R.; Donaldson, G. C.; Bucher, K.; Jendritzky, G.; Cordioli, E.; Martinelli, M.; Katsouyanni, K.; Kunst, A. E.; McDonald, C.; Näyhä, S.; Vuori, I.

    2000-01-01

    We report further details of the Eurowinter survey of cold related mortalities and protective measures against cold in seven regions of Europe, and review these with other evidence on the relationship of winter mortality to climate. Data for the oldest subject group studied, aged 65-74, showed that

  20. Women in Jordanian banks and performance: Financial accounting measurement

    Directory of Open Access Journals (Sweden)

    Muhannad Akram Ahmad

    2016-08-01

    Full Text Available This study highlights the gender diversity issues in the banking sector taking into consideration their impact on the performance measured by profitability (ROA. As the banking sector has widely been ignored from the previous studies due to their strict system, this study empirically examined the impact of the CEO gender and board with a female director on the performance of the Jordanian commercial banks in a period from 2004 to 2013. The multiple regression analysis shows that the banks with female CEOs underperform their counterparts run by male CEOs. The reason could be due to their harmonious relationships orientation; that is, women do not tend to invest in risky investments. However, female director plays insignificant roles on the performance which supports the evidence of tokenism as argued by the psychological social theory

  1. A programmable Gaussian random pulse generator for automated performance measurements

    International Nuclear Information System (INIS)

    Abdel-Aal, R.E.

    1989-01-01

    This paper describes a versatile random signal generator which produces logic pulses with a Gaussian distribution for the pulse spacing. The average rate at the pulse generator output can be software-programmed, which makes it useful in performing automated measurements of dead time and CPU time performance of data acquisition systems and modules over a wide range of data rates. Hardware and software components are described and data on the input-output characteristics and the statistical properties of the pulse generator are given. Typical applications are discussed together with advantages over using radioactive test sources. Results obtained from an automated performance run on a VAX 11/785 data acquisition system are presented. (orig.)

  2. Accreditation and the Development of Process Performance Measures

    DEFF Research Database (Denmark)

    Bie Bogh, Søren

    Accreditation is an external review process used to assess how well an organisation performs relative to established standards. Accreditation provides a framework for continuous quality improvement, and health services worldwide embrace accreditation and use it as a strategy to improve quality...... on quality of care using nationwide quantitative designs aimed at detecting changes over time in hospital performance in relation to both voluntary (Study 1) and mandatory accreditation (Study 2). Further, a qualitative study (Study 3) was conducted to complement the findings in Study 2. To examine...... was used to examine the mandatory accreditation programme. The quantitative study was a multilevel, longitudinal, stepped-wedge, nationwide study of process performance measures based on data from patients admitted for acute stroke, heart failure, ulcer, diabetes, breast cancer and lung cancer...

  3. Measuring the performance of mutual funds: A case study

    Directory of Open Access Journals (Sweden)

    Jakšić Milena

    2015-01-01

    Full Text Available In this paper we evaluate the performance of eight open-end mutual funds in the Republic of Serbia for the period 2009-2012, with the aim of testing the justification of active portfolio management of mutual funds, and determining the selection capability of Serbian portfolio managers. Risk-weighted returns of mutual funds are compared with the risk-weighted return of the leading Belgrade Stock Exchange index, Belex15, whereas the following are used as performance measures: Sharpe ratio (Si, Treynor ratio (Ti, and Jensen's or Alpha index (αi. The results suggest that the portfolio of Serbian mutual funds has inferior performance compared to the market portfolio, which indicates the lack of selection capabilities of domestic portfolio managers.

  4. Auditing emergency management programmes: Measuring leading indicators of programme performance.

    Science.gov (United States)

    Tomsic, Heather

    Emergency Management Programmes benefit from review and measurement against established criteria. By measuring current vs required programme elements for their actual currency, completeness and effectiveness, the resulting timely reports of achievements and documentation of identified gaps can effectively be used to rationally support prioritised improvement. Audits, with their detailed, triangulated and objectively weighted processes, are the ultimate approach in terms of programme content measurement. Although Emergency Management is often presented as a wholly separate operational mechanism, distinct and functionally different from the organisation's usual management structure, this characterisation is only completely accurate while managing an emergency itself. Otherwise, an organisation's Emergency Management Programme is embedded within that organisation and dependent upon it. Therefore, the organisation's culture and structure of management, accountability and measurement must be engaged for the programme to exist, much less improve. A wise and successful Emergency Management Coordinator does not let the separate and distinct nature of managing an emergency obscure their realisation of the need for an organisation to understand and manage all of the other programme components as part of its regular business practices. This includes its measurement. Not all organisations are sufficiently large or capable of supporting the use of an audit. This paper proposes that alternate, less formal, yet effective mechanisms can be explored, as long as they reflect and support organisational management norms, including a process of relatively informal measurement focused on the organisation's own perception of key Emergency Management Programme performance indicators.

  5. Design and experimentally measure a high performance metamaterial filter

    Science.gov (United States)

    Xu, Ya-wen; Xu, Jing-cheng

    2018-03-01

    Metamaterial filter is a kind of expecting optoelectronic device. In this paper, a metal/dielectric/metal (M/D/M) structure metamaterial filter is simulated and measured. Simulated results indicate that the perfect impedance matching condition between the metamaterial filter and the free space leads to the transmission band. Measured results show that the proposed metamaterial filter achieves high performance transmission on TM and TE polarization directions. Moreover, the high transmission rate is also can be obtained when the incident angle reaches to 45°. Further measured results show that the transmission band can be expanded through optimizing structural parameters. The central frequency of the transmission band is also can be adjusted through optimizing structural parameters. The physical mechanism behind the central frequency shifted is solved through establishing an equivalent resonant circuit model.

  6. Downtown People Mover (DPM) Winterization Test Demonstration : Otis Elevator

    Science.gov (United States)

    1982-01-01

    The Otis Elevator Company Transportation Technology Division (OTIS-TTD) Downtown People Mover (DPM) Winterization Test Demonstration Final Report covers the 1978-79 and 1979-80 winter periods. Tests were performed at the Otis test track in Denver, Co...

  7. Spirit's Winter Work Site

    Science.gov (United States)

    2006-01-01

    [figure removed for brevity, see original site] Annotated Version This portion of an image acquired by the Mars Reconnaissance Orbiter's High Resolution Imaging Science Experiment camera shows the Spirit rover's winter campaign site. Spirit was parked on a slope tilted 11 degrees to the north to maximize sunlight during the southern winter season. 'Tyrone' is an area where the rover's wheels disturbed light-toned soils. Remote sensing and in-situ analyses found the light-toned soil at Tyrone to be sulfate rich and hydrated. The original picture is catalogued as PSP_001513_1655_red and was taken on Sept. 29, 2006. NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, manages the Mars Reconnaissance Orbiter for NASA's Science Mission Directorate, Washington. Lockheed Martin Space Systems, Denver, is the prime contractor for the project and built the spacecraft. The High Resolution Imaging Science Experiment is operated by the University of Arizona, Tucson, and the instrument was built by Ball Aerospace and Technology Corp., Boulder, Colo.

  8. Winter School Les Houches

    CERN Document Server

    Lannoo, Michel; Bastard, Gérald; Voos, Michel; Boccara, Nino

    1986-01-01

    The Winter School held in Les Houches on March 12-21, 1985 was devoted to Semiconductor Heterojunctions and Superlattices, a topic which is recognized as being now one of the most interesting and active fields in semiconductor physics. In fact, following the pioneering work of Esaki and Tsu in 1970, the study of these two-dimensional semiconductor heterostructures has developed rapidly, both from the point of view of basic physics and of applications. For instance, modulation-doped heterojunctions are nowadays currently used to investigate the quantum Hall effect and to make very fast transistors. This book contains the lectures presented at this Winter School, showing in particular that many aspects of semiconductor heterojunctions and super­ lattices were treated, extending from the fabrication of these two-dimensional systems to their basic properties and applications in micro-and opto-electron­ ics. Among the subjects which were covered, one can quote as examples: molecular beam epitaxy and metallorgani...

  9. Zone of Acceptance Under Performance Measurement: Does Performance Information Affect Employee Acceptance of Management Authority?

    DEFF Research Database (Denmark)

    Nielsen, Poul Aaes; Jacobsen, Christian Bøtcher

    2018-01-01

    Public sector employees have traditionally enjoyed substantial influence and bargaining power in organizational decision making, but few studies have investigated the formation of employee acceptance of management authority. Drawing on the “romance of leadership” perspective, the authors argue th...... that performance measurement can alter public sector authority relations and have implications regarding how public managers can use performance information strategically to gain acceptance of management authority and organizational change....

  10. Sources and performance criteria of uncertainty of reference measurement procedures.

    Science.gov (United States)

    Mosca, Andrea; Paleari, Renata

    2018-05-29

    This article wants to focus on the today available Reference Measurement Procedures (RMPs) for the determination of various analytes in Laboratory Medicine and the possible tools to evaluate their performance in the laboratories who are currently using them. A brief review on the RMPs has been performed by investigating the Joint Committee for Traceability in Laboratory Medicine (JCTLM) database. In order to evaluate their performances, we have checked the organization of three international ring trials, i.e. those regularly performed by the IFCC External Quality assessment scheme for Reference Laboratories in Laboratory Medicine (RELA), by the Center for Disease Control and Prevention (CDC) cholesterol network and by the IFCC Network for HbA 1c . Several RMPs are available through the JCTLM database, but the best way to collect information about the RMPs and their uncertainties is to look at the reference measurement service providers (RMS). This part of the database and the background on how to listed in the database is very helpful for the assessment of expanded uncertainty (MU) and performance in general of RMPs. Worldwide, 17 RMS are listed in the database, and for most of the measurands more than one RMS is able to run the relative RMPs, with similar expanded uncertainties. As an example, for a-amylase, 4 SP offer their services with MU between 1.6 and 3.3%. In other cases (such as total cholesterol, the U may span over a broader range, i.e. from 0.02 to 3.6%). With regard to the performance evaluation, the approach is often heterogenous, and it is difficult to compare the performance of laboratories running the same RMP for the same measurand if involved in more than one EQAS. The reference measurement services have been created to help laboratory professionals and manufacturers to implement the correct metrological traceability, and the JCTLM database is the only correct way to retrieve all the necessary important information to this end. Copyright © 2018

  11. Why do employees take more initiatives to improve their performance after co-developing performance measures? A field study

    NARCIS (Netherlands)

    Groen, B.A.C.; Wouters, M.J.F.; Wilderom, C.P.M.

    2012-01-01

    Performance measurements may stimulate employee initiatives to improve operational performance, especially when employees themselves participate in the development of their own departmental performance measures. Using the theory of planned behavior, we examine why this occurs in a beverage

  12. Why do employees take more initiatives to improve their performance after co-developing performance measures? A field study.

    NARCIS (Netherlands)

    Groen, B.A.C.; Wouters, Marc; Wilderom, Celeste P.M.

    2012-01-01

    Performance measurements may stimulate employee initiatives to improve operational performance, especially when employees themselves participate in the development of their own departmental performance measures. Using the theory of planned behavior, we examine why this occurs in a beverage

  13. Performance measurement systems, TQM, and multi-level firm performance: a person-organisation fit perspective

    OpenAIRE

    Wei, Jo-Ting; Chang, Yeun Wen; Zhang, Xiaoxiang; Wu, Hsin-Hung

    2017-01-01

    For firms implementing TQM, there is a need to redesign performance measurement systems (PMS). Innovated PMS ought to have measurement diversity in their structure with considering the spirit of TQM and emphasize the congruence of goals between employees and firms by adding the viewpoint of person-organisation fit (P-O fit). This paper adopts structural equation modeling (SEM) to examine Taiwanese manufacturing firms to study the association between the P-O fit of PMS and the implementation o...

  14. Reducing Uncertainty: Implementation of Heisenberg Principle to Measure Company Performance

    Directory of Open Access Journals (Sweden)

    Anna Svirina

    2015-08-01

    Full Text Available The paper addresses the problem of uncertainty reduction in estimation of future company performance, which is a result of wide range of enterprise's intangible assets probable efficiency. To reduce this problem, the paper suggests to use quantum economy principles, i.e. implementation of Heisenberg principle to measure efficiency and potential of intangible assets of the company. It is proposed that for intangibles it is not possible to estimate both potential and efficiency at a certain time point. To provide a proof for these thesis, the data on resources potential and efficiency from mid-Russian companies was evaluated within deterministic approach, which did not allow to evaluate probability of achieving certain resource efficiency, and quantum approach, which allowed to estimate the central point around which the probable efficiency of resources in concentrated. Visualization of these approaches was performed by means of LabView software. It was proven that for tangible assets performance estimation a deterministic approach should be used; while for intangible assets the quantum approach allows better quality of future performance prediction. On the basis of these findings we proposed the holistic approach towards estimation of company resource efficiency in order to reduce uncertainty in modeling company performance.

  15. Analysis of Illinois Home Performance with ENERGY STAR® Measure Packages

    Energy Technology Data Exchange (ETDEWEB)

    Baker, J. [Partnership for Advanced Residential Retrofit (PARR), Chicago, IL (United States); Yee, S. [Partnership for Advanced Residential Retrofit (PARR), Chicago, IL (United States); Brand, L. [Partnership for Advanced Residential Retrofit (PARR), Chicago, IL (United States)

    2013-09-01

    Through the Chicagoland Single Family Housing Characterization and Retrofit Prioritization report, the Partnership for Advanced Residential Retrofit research team characterized 15 housing types in the Chicagoland region based on assessor data, utility billing history, and available data from prior energy efficiency programs. Within these 15 groups, a subset showed the greatest opportunity for energy savings based on BEopt Version 1.1 modeling of potential energy efficiency package options and the percent of the housing stock represented by each group. In this project, collected field data from a whole-home program in Illinois are utilized to compare marketplace-installed measures to the energy saving optimal packages previously developed for the 15 housing types. Housing type, conditions, energy efficiency measures installed, and retrofit cost information were collected from 19 homes that participated in the Illinois Home Performance with ENERGY STAR program in 2012, representing eight of the characterized housing groups. Two were selected for further case study analysis to provide an illustration of the differences between optimal and actually installed measures. Taken together, these homes are representative of 34.8% of the Chicagoland residential building stock. In one instance, actual installed measures closely matched optimal recommended measures.

  16. DESIGNING COMPANY PERFORMANCE MEASUREMENT SYSTEM USING BALANCE SCORECARD APPROACH

    Directory of Open Access Journals (Sweden)

    Cecep Mukti Soleh

    2015-05-01

    Full Text Available This research aimed to design how to measure company performance by using balance scorecard approach in coal transportation services industry. Depth interview was used to obtain qualitative data determination of strategic objectives, key performance indicators, strategic initiatives, and in charge units for each balanced scorecard perspectives while the quantitative data were obtained from weighting through questionnaires and analyzed using paired comparison to get a perspective what mostly affected the performance of the company. To measure the achievement of corporate performance, each KPI used (1 the scoring system with the methods that higher is better, lower is better and precise is better; (2 traffic light system with the help of green, yellow, red for identification of target achievement. This research result shows that in the balance scorecard perspective, the most influences on the overall performance of the company include the customer's perspective (31%, financial perspective (29%, internal business processes (21%, learning, and growth 19%. Keywords: balance scorecard, paired comparison, coal transportation serviceABSTRAKPenelitian ini bertujuan untuk merancang pengukuran kinerja perusahaan dengan menggunakan pendekatan balance scorecard di industri jasa pengangkutan batu bara. Data kualitatif diperoleh melalui indepth interview digunakan untuk menentukan sasaran strategik, indikator kinerja utama, inisiatif strategi dan penanggungjawab setiap divisi setiap perspektif balance scorecard, sedangkan data kuantitatif digunakan untuk pembobotan melalui kuesioner dan dianalisis dengan menggunakan metode paired comparisson untuk mendapatkan perspektif yang paling berpengaruh terhadap kinerja perusahaan. Ukuran pencapaian kinerja perusahaan dari setiap KPI menggunakan; (1 scoring system dengan bantuan metode higher is better, lower is better dan precise is better;(2 traffic light system dengan menggunakan bantuan warna hijau, kuning, merah

  17. Dehydration and performance on clinical concussion measures in collegiate wrestlers.

    Science.gov (United States)

    Weber, Amanda Friedline; Mihalik, Jason P; Register-Mihalik, Johna K; Mays, Sally; Prentice, William E; Guskiewicz, Kevin M

    2013-01-01

    The effects of dehydration induced by wrestling-related weight-cutting tactics on clinical concussion outcomes, such as neurocognitive function, balance performance, and symptoms, have not been adequately studied. To evaluate the effects of dehydration on the outcome of clinical concussion measures in National Collegiate Athletic Association Division I collegiate wrestlers. Repeated-measures design. Clinical research laboratory. Thirty-two Division I healthy collegiate male wrestlers (age = 20.0 ± 1.4 years; height = 175.0 ± 7.5 cm; baseline mass = 79.2 ± 12.6 kg). Participants completed preseason concussion baseline testing in early September. Weight and urine samples were also collected at this time. All participants reported to prewrestling practice and postwrestling practice for the same test battery and protocol in mid-October. They had begun practicing weight-cutting tactics a day before prepractice and postpractice testing. Differences between these measures permitted us to evaluate how dehydration and weight-cutting tactics affected concussion measures. Sport Concussion Assessment Tool 2 (SCAT2), Balance Error Scoring System, Graded Symptom Checklist, and Simple Reaction Time scores. The Simple Reaction Time was measured using the Automated Neuropsychological Assessment Metrics. The SCAT2 measurements were lower at prepractice (P = .002) and postpractice (P < .001) when compared with baseline. The BESS error scores were higher at postpractice when compared with baseline (P = .015). The GSC severity scores were higher at prepractice (P = .011) and postpractice (P < .001) than at baseline and at postpractice when than at prepractice (P = .003). The number of Graded Symptom Checklist symptoms reported was also higher at prepractice (P = .036) and postpractice (P < .001) when compared with baseline, and at postpractice when compared with prepractice (P = .003). Our results suggest that it is important for wrestlers to be evaluated in a euhydrated state to

  18. Measuring the performance of G2G services in Iran

    Science.gov (United States)

    Zarei, Behrouz; Safdari, Maryam

    To highlight the growth of e-government and the importance of its services it is essential to evaluate the performance of the service delivery to customers. Research indicates that traditional performance indexes are not suitable for this evaluation; moreover, it is noticeable that the e-government services are intangible and invisible. Among different e-government services, measurement of quality government to government (G2G) services has been less attractive for researchers while crucial for government policy-makers. This calls for a better understanding of the specific needs of users of these services in order to provide appropriate type and level of services that meets those needs. In this paper, the performance of the G2G services is measured in the Iranian context. For this purpose, SERVQUAL, which is a well-known method for assessing service quality, is employed. This study proposes and tests a five-factor of SERVQUAL instrument to explain user satisfaction and gap analysis, between expectations and perceptions of its customers, consisting thirty ministries and main governmental organizations. Based on a Chi-square test, factor analysis, gap analysis and correlations, it is concluded the gap between expectations and perceptions of G2G customers is significant and customer satisfaction of G2G services is at low level.

  19. Subsurface Biogeochemical Research FY11 Second Quarter Performance Measure

    Energy Technology Data Exchange (ETDEWEB)

    Scheibe, Timothy D.

    2011-03-31

    The Subsurface Biogeochemical Research (SBR) Long Term Measure for 2011 under the Performance Assessment Rating Tool (PART) measure is to "Refine subsurface transport models by developing computational methods to link important processes impacting contaminant transport at smaller scales to the field scale." The second quarter performance measure is to "Provide a report on computational methods linking genome-enabled understanding of microbial metabolism with reactive transport models to describe processes impacting contaminant transport in the subsurface." Microorganisms such as bacteria are by definition small (typically on the order of a micron in size), and their behavior is controlled by their local biogeochemical environment (typically within a single pore or a biofilm on a grain surface, on the order of tens of microns in size). However, their metabolic activity exerts strong influence on the transport and fate of groundwater contaminants of significant concern at DOE sites, in contaminant plumes with spatial extents of meters to kilometers. This report describes progress and key findings from research aimed at integrating models of microbial metabolism based on genomic information (small scale) with models of contaminant fate and transport in aquifers (field scale).

  20. Performance Measurement and Management Promotion through Non-Financial Measures: A Management Accounting Perspective

    OpenAIRE

    Eisenberg, Paul

    2016-01-01

    The purpose of this paper is the discussion of non-financial performance measures that can be adopted in the management accounting function of business organisations. The study is important because it shows how organisational focus on non-financial measures can substantially enhance profitability, albeit being subject to cost constraints. To begin with, the evolution of management accounting research over the last three decades is resented. The development in the academia is then contra...

  1. Severe European winters in a secular perspective

    Science.gov (United States)

    Hoy, Andreas; Hänsel, Stephanie

    2017-04-01

    Temperature conditions during the winter time are substantially shaped by a strong year-to-year variability. European winters since the late 1980s - compared to previous decades and centuries - were mainly characterised by a high temperature level, including recent record-warm winters. Yet, comparably cold winters and severe cold spells still occur nowadays, like recently observed from 2009 to 2013 and in early 2017. Central England experienced its second coldest December since start of observations more than 350 years ago in 2010, and some of the lowest temperatures ever measured in northern Europe (below -50 °C in Lapland) were recorded in January 1999. Analysing thermal characteristics and spatial distribution of severe (historical) winters - using early instrumental data - helps expanding and consolidating our knowledge of past weather extremes. This contribution presents efforts towards this direction. We focus on a) compiling and assessing a very long-term instrumental, spatially widespread and well-distributed, high-quality meteorological data set to b) investigate very cold winter temperatures in Europe from early measurements until today. In a first step, we analyse the longest available time series of monthly temperature averages within Europe. Our dataset extends from the Nordic countries up to the Mediterranean and from the British Isles up to Russia. We utilise as much as possible homogenised times series in order to ensure reliable results. Homogenised data derive from the NORDHOM (Scandinavia) and HISTALP (greater alpine region) datasets or were obtained from national weather services and universities. Other (not specifically homogenised) data were derived from the ECA&D dataset or national institutions. The employed time series often start already during the 18th century, with Paris & Central England being the longest datasets (from 1659). In a second step, daily temperature averages are involved. Only some of those series are homogenised, but

  2. The Multifactor Measure of Performance: Its Development, Norming, and Validation.

    Science.gov (United States)

    Bar-On, Reuven

    2018-01-01

    This article describes the development as well as the initial norming and validation of the Multifactor Measure of Performance™ (MMP™), which is a psychometric instrument that is designed to study, assess and enhance key predictors of human performance to help individuals perform at a higher level. It was created by the author, for the purpose of going beyond existing conceptual and psychometric models that often focus on relatively few factors that are purported to assess performance at school, in the workplace and elsewhere. The relative sparsity of multifactorial pre-employment assessment instruments exemplifies, for the author, one of the important reasons for developing the MMP™, which attempts to comprehensively evaluate a wider array of factors that are thought to contribute to performance. In that this situation creates a need in the area of test-construction that should be addressed, the author sought to develop a multifactorial assessment and development instrument that could concomitantly evaluate a combination of physical, cognitive, intra-personal, inter-personal, and motivational factors that significantly contribute to performance. The specific aim of this article is to show why, how and if this could be done as well as to present and discuss the potential importance of the results obtained to date. The findings presented here will hopefully add to what is known about human performance and thus contribute to the professional literature, in addition to contribute to the continued development of the MMP™. The impetus for developing the MMP™ is first explained below, followed by a detailed description of the process involved and the findings obtained; and their potential application is then discussed as well as the possible limitations of the present research and the need for future studies to address them.

  3. Performance measures for aging of nuclear power plants

    International Nuclear Information System (INIS)

    Ross, D.F. Jr.

    1993-01-01

    The Nuclear Power Plant licenses are granted by the US Nuclear Regulatory Commission (NRC) for a 40-year term. There is at present consideration being given to extending the authorized service lifetime beyond that, perhaps for a total of 60 or 70 years total. A logical concern for such a length of operation is whether the plant ages in such a way as to be significantly less safe as it gets older. As a corollary to this, there would be the question as to how to measure a diminution in plant safety. Each operating utility has, of course, ways to observe the plant performance. It has maintenance and surveillance programs which are used for this purpose. The NRC maintains a presence at each operating plant in the form of resident inspectors. The NRC also receives utility reports which may then be used to synthesize operating performance. It also reviews plant performance directly through what is known as the Systematic Assessment of Licensee Performance (SALP). In the paper the various data management programs used by the NRC will be described. The results of each program is presented, and observations are made as to the potential effect of age on safety performance. It is also necessary to define the size of the population being examined. There are at present 109 operating reactors. The age distribution is used to normalize the data. Some of the indicators discussed in this paper are concerned more with the indirect effect of aging, such as inadvertent shutdown. The regulated industry maintains a program known as the Nuclear Power Reliability Data System (NPRDS) to which the electric utilities participate in a voluntary manner. Data from NPRDS can be accessed to observe the direct aging effect; this is not covered in this paper. To the degree that plant operating staff learns how to cope with aging equipment and operate in a safe manner nonetheless, the performance indicators would not fully reflect the aging effect

  4. Performance and measurements of the AGS and Booster beams

    International Nuclear Information System (INIS)

    Weng, W.T.

    1995-01-01

    Analyses of Hot Gas Stream Cleanup (HGSC) ashes and descriptions of filter performance were made to address the problems with filter operation that are apparently linked to the collected ash. This task is designed to generate data base of the key properties of ashes collected from operating advanced particle filters and to relate these ash properties to the operation and performance of these filters. Activities including initial formatting of the data base and entry, modification of the permeability model, and initial design of a high-temperature test device for measuring uncompacted bulk porosity of ash aggregates (indicator of relative cohesivity of the ash, filter cake porosity/permeability). Chemical analyses of hopper and filter cake ashes from Tidd showed that the consolidation degree could not be accounted for by condensation/adsorption from the flue gas; the mechanism is likely physical rearrangement of the ash particles

  5. Measuring Human Performance within Computer Security Incident Response Teams

    Energy Technology Data Exchange (ETDEWEB)

    McClain, Jonathan T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Silva, Austin Ray [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Avina, Glory Emmanuel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Forsythe, James C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    Human performance has become a pertinen t issue within cyber security. However, this research has been stymied by the limited availability of expert cyber security professionals. This is partly attributable to the ongoing workload faced by cyber security professionals, which is compound ed by the limited number of qualified personnel and turnover of p ersonnel across organizations. Additionally, it is difficult to conduct research, and particularly, openly published research, due to the sensitivity inherent to cyber ope rations at most orga nizations. As an alternative, the current research has focused on data collection during cyb er security training exercises. These events draw individuals with a range of knowledge and experience extending from seasoned professionals to recent college gradu ates to college students. The current paper describes research involving data collection at two separate cyber security exercises. This data collection involved multiple measures which included behavioral performance based on human - machine transactions and questionnaire - based assessments of cyber security experience.

  6. Introducing care pathway commissioning to primary dental care: measuring performance.

    Science.gov (United States)

    Harris, R; Bridgman, C; Ahmad, M; Bowes, L; Haley, R; Saleem, S; Singh, R; Taylor, S

    2011-12-09

    Care pathways have been used in a variety of ways: firstly to support quality improvement through standardising clinical processes, but also for secondary purposes, by purchasers of healthcare, to monitor activity and health outcomes and to commission services. This paper focuses on reporting a secondary use of care pathways: to commission and monitor performance of primary dental care services. Findings of a project involving three dental practices implementing a system based on rating patients according to their risk of disease and need for care are outlined. Data from surgery-based clinical databases and interviews from commissioners and providers are reported. The use of both process and outcome key performance indicators in this context is discussed, as well as issues which arise such as attributability of outcome measures and strategic approaches to improving quality of care.

  7. Financial Indicators of Performance Measurement: Reality, Relevance and Distortion

    Directory of Open Access Journals (Sweden)

    Flavius-Andrei Guinea

    2016-01-01

    Full Text Available The main criticism brought to managers and to managerial accounting systems was the lack of emphasis on the return of the use of invested capital and the excessive focus on the efficiency of production processes. This fact forced the transition to a new view on the way of establishing the strategic objectives measured by financial indicators. The aim of this paper is to demonstrate, through case studies, the relevance and possibilities of manipulation of a series of indicators used for assessing performance: return on investment, residual profit, economic added value, commercial profitability. The relativity and the criticized appraisal of performance only through the means of profit were thought to be solved by implementing other indicators that would link several ingredients of profitability. The conclusions highlight that the remedy promoted by the new sets of financial indicators imposes a considerable cost, represented by the temptation of information distortion.

  8. Measurement-Based Performance Evaluation of Advanced MIMO Transceiver Designs

    Directory of Open Access Journals (Sweden)

    Schneider Christian

    2005-01-01

    Full Text Available This paper describes the methodology and the results of performance investigations on a multiple-input multiple-output (MIMO transceiver scheme for frequency-selective radio channels. The method relies on offline simulations and employs real-time MIMO channel sounder measurement data to ensure a realistic channel modeling. Thus it can be classified in between the performance evaluation using some predefined channel models and the evaluation of a prototype hardware in field experiments. New aspects for the simulation setup are discussed, which are frequently ignored when using simpler model-based evaluations. Example simulations are provided for an iterative ("turbo" MIMO equalizer concept. The dependency of the achievable bit error rate performance on the propagation characteristics and on the variation in some system design parameters is shown, whereas the antenna constellation is of particular concern for MIMO systems. Although in many of the considered constellations turbo MIMO equalization appears feasible in real field scenarios, there exist cases with poor performance as well, indicating that in practical applications link adaptation of the transmitter and receiver processing to the environment is necessary.

  9. Optimisation of key performance measures in air cargo demand management

    Directory of Open Access Journals (Sweden)

    Alexander May

    2014-04-01

    Full Text Available This article sought to facilitate the optimisation of key performance measures utilised for demand management in air cargo operations. The focus was on the Revenue Management team at Virgin Atlantic Cargo and a fuzzy group decision-making method was used. Utilising intelligent fuzzy multi-criteria methods, the authors generated a ranking order of ten key outcome-based performance indicators for Virgin Atlantic air cargo Revenue Management. The result of this industry-driven study showed that for Air Cargo Revenue Management, ‘Network Optimisation’ represents a critical outcome-based performance indicator. This collaborative study contributes to existing logistics management literature, especially in the area of Revenue Management, and it seeks to enhance Revenue Management practice. It also provides a platform for Air Cargo operators seeking to improve reliability values for their key performance indicators as a means of enhancing operational monitoring power.

  10. Performance Measurements in a High Throughput Computing Environment

    CERN Document Server

    AUTHOR|(CDS)2145966; Gribaudo, Marco

    The IT infrastructures of companies and research centres are implementing new technologies to satisfy the increasing need of computing resources for big data analysis. In this context, resource profiling plays a crucial role in identifying areas where the improvement of the utilisation efficiency is needed. In order to deal with the profiling and optimisation of computing resources, two complementary approaches can be adopted: the measurement-based approach and the model-based approach. The measurement-based approach gathers and analyses performance metrics executing benchmark applications on computing resources. Instead, the model-based approach implies the design and implementation of a model as an abstraction of the real system, selecting only those aspects relevant to the study. This Thesis originates from a project carried out by the author within the CERN IT department. CERN is an international scientific laboratory that conducts fundamental researches in the domain of elementary particle physics. The p...

  11. Performance measurement integrated information framework in e-Manufacturing

    Science.gov (United States)

    Teran, Hilaida; Hernandez, Juan Carlos; Vizán, Antonio; Ríos, José

    2014-11-01

    The implementation of Internet technologies has led to e-Manufacturing technologies becoming more widely used and to the development of tools for compiling, transforming and synchronising manufacturing data through the Web. In this context, a potential area for development is the extension of virtual manufacturing to performance measurement (PM) processes, a critical area for decision making and implementing improvement actions in manufacturing. This paper proposes a PM information framework to integrate decision support systems in e-Manufacturing. Specifically, the proposed framework offers a homogeneous PM information exchange model that can be applied through decision support in e-Manufacturing environment. Its application improves the necessary interoperability in decision-making data processing tasks. It comprises three sub-systems: a data model, a PM information platform and PM-Web services architecture. A practical example of data exchange for measurement processes in the area of equipment maintenance is shown to demonstrate the utility of the model.

  12. PERFORMANCE EVALUATION OF THERMOGRAPHIC CAMERAS FOR PHOTOGRAMMETRIC MEASUREMENTS

    Directory of Open Access Journals (Sweden)

    N. Yastikli

    2013-05-01

    Full Text Available The aim of this research is the performance evaluation of the termographic cameras for possible use for photogrammetric documentation and deformation analyses caused by moisture and isolation problem of the historical and cultural heritage. To perform geometric calibration of the termographic camera, the 3D test object was designed with 77 control points which were distributed in different depths. For performance evaluation, Flir A320 termographic camera with 320 × 240 pixels and lens with 18 mm focal length was used. The Nikon D3X SLR digital camera with 6048 × 4032 pixels and lens with 20 mm focal length was used as reference for comparison. The size of pixel was 25 μm for the Flir A320 termographic camera and 6 μm for the Nikon D3X SLR digital camera. The digital images of the 3D test object were recorded with the Flir A320 termographic camera and Nikon D3X SLR digital camera and the image coordinate of the control points in the images were measured. The geometric calibration parameters, including the focal length, position of principal points, radial and tangential distortions were determined with introduced additional parameters in bundle block adjustments. The measurement of image coordinates and bundle block adjustments with additional parameters were performed using the PHIDIAS digital photogrammetric system. The bundle block adjustment was repeated with determined calibration parameter for both Flir A320 termographic camera and Nikon D3X SLR digital camera. The obtained standard deviation of measured image coordinates was 9.6 μm and 10.5 μm for Flir A320 termographic camera and 8.3 μm and 7.7 μm for Nikon D3X SLR digital camera. The obtained standard deviation of measured image points in Flir A320 termographic camera images almost same accuracy level with digital camera in comparison with 4 times bigger pixel size. The obtained results from this research, the interior geometry of the termographic cameras and lens distortion was

  13. Performance Evaluation of Thermographic Cameras for Photogrammetric Measurements

    Science.gov (United States)

    Yastikli, N.; Guler, E.

    2013-05-01

    The aim of this research is the performance evaluation of the termographic cameras for possible use for photogrammetric documentation and deformation analyses caused by moisture and isolation problem of the historical and cultural heritage. To perform geometric calibration of the termographic camera, the 3D test object was designed with 77 control points which were distributed in different depths. For performance evaluation, Flir A320 termographic camera with 320 × 240 pixels and lens with 18 mm focal length was used. The Nikon D3X SLR digital camera with 6048 × 4032 pixels and lens with 20 mm focal length was used as reference for comparison. The size of pixel was 25 μm for the Flir A320 termographic camera and 6 μm for the Nikon D3X SLR digital camera. The digital images of the 3D test object were recorded with the Flir A320 termographic camera and Nikon D3X SLR digital camera and the image coordinate of the control points in the images were measured. The geometric calibration parameters, including the focal length, position of principal points, radial and tangential distortions were determined with introduced additional parameters in bundle block adjustments. The measurement of image coordinates and bundle block adjustments with additional parameters were performed using the PHIDIAS digital photogrammetric system. The bundle block adjustment was repeated with determined calibration parameter for both Flir A320 termographic camera and Nikon D3X SLR digital camera. The obtained standard deviation of measured image coordinates was 9.6 μm and 10.5 μm for Flir A320 termographic camera and 8.3 μm and 7.7 μm for Nikon D3X SLR digital camera. The obtained standard deviation of measured image points in Flir A320 termographic camera images almost same accuracy level with digital camera in comparison with 4 times bigger pixel size. The obtained results from this research, the interior geometry of the termographic cameras and lens distortion was modelled efficiently

  14. Methodology for performing measurements to release material from radiological control

    International Nuclear Information System (INIS)

    Durham, J.S.; Gardner, D.L.

    1993-09-01

    This report describes the existing and proposed methodologies for performing measurements of contamination prior to releasing material for uncontrolled use at the Hanford Site. The technical basis for the proposed methodology, a modification to the existing contamination survey protocol, is also described. The modified methodology, which includes a large-area swipe followed by a statistical survey, can be used to survey material that is unlikely to be contaminated for release to controlled and uncontrolled areas. The material evaluation procedure that is used to determine the likelihood of contamination is also described

  15. Improving Supply Chain Risk Management by Introducing Performance Measurement Systems

    OpenAIRE

    Ryding, Anna; Sahlin, Jonatan

    2013-01-01

    Supply chain risk management (SCRM) is a topic that gains more and more interest from both the academic and practitioner’s perspective. The reason for this is the increased complexity in the global supply chain (SC) networks and many managers do not realize the risks they build in their SC by the continuous search to cut cost and decrease tied up capital. One problem with SCRM is that it is hard to measure the performance of it and if it is really beneficial to work with it. The objective for...

  16. Predictive Measures of Locomotor Performance on an Unstable Walking Surface

    Science.gov (United States)

    Bloomberg, J. J.; Peters, B. T.; Mulavara, A. P.; Caldwell, E. E.; Batson, C. D.; De Dios, Y. E.; Gadd, N. E.; Goel, R.; Wood, S. J.; Cohen, H. S.; hide

    2016-01-01

    Locomotion requires integration of visual, vestibular, and somatosensory information to produce the appropriate motor output to control movement. The degree to which these sensory inputs are weighted and reorganized in discordant sensory environments varies by individual and may be predictive of the ability to adapt to novel environments. The goals of this project are to: 1) develop a set of predictive measures capable of identifying individual differences in sensorimotor adaptability, and 2) use this information to inform the design of training countermeasures designed to enhance the ability of astronauts to adapt to gravitational transitions improving balance and locomotor performance after a Mars landing and enhancing egress capability after a landing on Earth.

  17. Performance measures in the earth observations commercialization applications program

    Science.gov (United States)

    Macauley, Molly K.

    1996-03-01

    Performance measures in the Earth Observations Commercialization Application Program (EOCAP) are key to its success and include net profitability; enhancements to industry productivity through generic innovations in industry practices, standards, and protocols; and documented contributions to public policy governing the newly developing remote sensing industry. Because EOCAP requires company co-funding, both parties to the agreement (the government and the corporate partner) have incentives to pursue these goals. Further strengthening progress towards these goals are requirements for business plans in the company's EOCAP proposal, detailed scrutiny given these plans during proposal selection, and regularly documented progress reports during project implementation.

  18. Spirit Scans Winter Haven

    Science.gov (United States)

    2006-01-01

    At least three different kinds of rocks await scientific analysis at the place where NASA's Mars Exploration Rover Spirit will likely spend several months of Martian winter. They are visible in this picture, which the panoramic camera on Spirit acquired during the rover's 809th sol, or Martian day, of exploring Mars (April 12, 2006). Paper-thin layers of light-toned, jagged-edged rocks protrude horizontally from beneath small sand drifts; a light gray rock with smooth, rounded edges sits atop the sand drifts; and several dark gray to black, angular rocks with vesicles (small holes) typical of hardened lava lie scattered across the sand. This view is an approximately true-color rendering that combines images taken through the panoramic camera's 753-nanometer, 535-nanometer, and 432-nanometer filters.

  19. Winter fuels report

    International Nuclear Information System (INIS)

    1995-01-01

    The Winter Fuels Report is intended to provide concise, timely information to the industry, the press, policymakers, consumers, analysts, and State and local governments on the following topics: distillate fuel oil net production, imports and stocks on a US level and for all Petroleum Administration for Defense Districts (PADD) and product supplied on a US level; propane net production, imports and stocks on a US level and for PADD's I, II, and III; natural gas supply and disposition and underground storage for the US and consumption for all PADD's, as well as selected National average prices; residential and wholesale pricing data for heating oil and propane for those States participating in the joint Energy Information Administration (EIA)/State Heating Oil and Propane Program; crude oil and petroleum price comparisons for the US and selected cities; and a 6-10 day, 30-Day, and 90-Day outlook for temperature and precipitation and US total heating degree-days by city

  20. Winter fuels report

    Energy Technology Data Exchange (ETDEWEB)

    1990-11-29

    The Winter Fuels Report is intended to provide concise, timely information to the industry, the press, policymakers, consumers, analysts, and state and local governments on the following topics: distillate fuel oil net production, imports and stocks for all PADD's and product supplied on a US level; propane net product supplied on a US level; propane net production, imports and stocks for Petroleum Administration for Defense Districts (PADD) I, II, and III; natural gas supply and disposition and underground storage for the United States and consumption for all PADD's; residential and wholesale pricing data for propane and heating oil for those states participating in the joint Energy Information Administration (EIA)/State Heating Oil and Propane Program; crude oil and petroleum price comparisons for the United States and selected cities; and US total heating degree-days by city. 27 figs, 12 tabs.

  1. On summary measure analysis of linear trend repeated measures data: performance comparison with two competing methods.

    Science.gov (United States)

    Vossoughi, Mehrdad; Ayatollahi, S M T; Towhidi, Mina; Ketabchi, Farzaneh

    2012-03-22

    The summary measure approach (SMA) is sometimes the only applicable tool for the analysis of repeated measurements in medical research, especially when the number of measurements is relatively large. This study aimed to describe techniques based on summary measures for the analysis of linear trend repeated measures data and then to compare performances of SMA, linear mixed model (LMM), and unstructured multivariate approach (UMA). Practical guidelines based on the least squares regression slope and mean of response over time for each subject were provided to test time, group, and interaction effects. Through Monte Carlo simulation studies, the efficacy of SMA vs. LMM and traditional UMA, under different types of covariance structures, was illustrated. All the methods were also employed to analyze two real data examples. Based on the simulation and example results, it was found that the SMA completely dominated the traditional UMA and performed convincingly close to the best-fitting LMM in testing all the effects. However, the LMM was not often robust and led to non-sensible results when the covariance structure for errors was misspecified. The results emphasized discarding the UMA which often yielded extremely conservative inferences as to such data. It was shown that summary measure is a simple, safe and powerful approach in which the loss of efficiency compared to the best-fitting LMM was generally negligible. The SMA is recommended as the first choice to reliably analyze the linear trend data with a moderate to large number of measurements and/or small to moderate sample sizes.

  2. Classroom Composition and Measured Teacher Performance: What Do Teacher Observation Scores Really Measure?

    Science.gov (United States)

    Steinberg, Matthew P.; Garrett, Rachel

    2016-01-01

    As states and districts implement more rigorous teacher evaluation systems, measures of teacher performance are increasingly being used to support instruction and inform retention decisions. Classroom observations take a central role in these systems, accounting for the majority of teacher ratings upon which accountability decisions are based.…

  3. Mapping Winter Wheat with Multi-Temporal SAR and Optical Images in an Urban Agricultural Region.

    Science.gov (United States)

    Zhou, Tao; Pan, Jianjun; Zhang, Peiyu; Wei, Shanbao; Han, Tao

    2017-05-25

    Winter wheat is the second largest food crop in China. It is important to obtain reliable winter wheat acreage to guarantee the food security for the most populous country in the world. This paper focuses on assessing the feasibility of in-season winter wheat mapping and investigating potential classification improvement by using SAR (Synthetic Aperture Radar) images, optical images, and the integration of both types of data in urban agricultural regions with complex planting structures in Southern China. Both SAR (Sentinel-1A) and optical (Landsat-8) data were acquired, and classification using different combinations of Sentinel-1A-derived information and optical images was performed using a support vector machine (SVM) and a random forest (RF) method. The interference coherence and texture images were obtained and used to assess the effect of adding them to the backscatter intensity images on the classification accuracy. The results showed that the use of four Sentinel-1A images acquired before the jointing period of winter wheat can provide satisfactory winter wheat classification accuracy, with an F1 measure of 87.89%. The combination of SAR and optical images for winter wheat mapping achieved the best F1 measure-up to 98.06%. The SVM was superior to RF in terms of the overall accuracy and the kappa coefficient, and was faster than RF, while the RF classifier was slightly better than SVM in terms of the F1 measure. In addition, the classification accuracy can be effectively improved by adding the texture and coherence images to the backscatter intensity data.

  4. Model Engine Performance Measurement From Force Balance Instrumentation

    Science.gov (United States)

    Jeracki, Robert J.

    1998-01-01

    A large scale model representative of a low-noise, high bypass ratio turbofan engine was tested for acoustics and performance in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. This test was part of NASA's continuing Advanced Subsonic Technology Noise Reduction Program. The low tip speed fan, nacelle, and an un-powered core passage (with core inlet guide vanes) were simulated. The fan blades and hub are mounted on a rotating thrust and torque balance. The nacelle, bypass duct stators, and core passage are attached to a six component force balance. The two balance forces, when corrected for internal pressure tares, measure the total thrust-minus-drag of the engine simulator. Corrected for scaling and other effects, it is basically the same force that the engine supports would feel, operating at similar conditions. A control volume is shown and discussed, identifying the various force components of the engine simulator thrust and definitions of net thrust. Several wind tunnel runs with nearly the same hardware installed are compared, to identify the repeatability of the measured thrust-minus-drag. Other wind tunnel runs, with hardware changes that affected fan performance, are compared to the baseline configuration, and the thrust and torque effects are shown. Finally, a thrust comparison between the force balance and nozzle gross thrust methods is shown, and both yield very similar results.

  5. Performance measurement of supply chain flexibility using witness

    Directory of Open Access Journals (Sweden)

    Rituraj Chandrakar

    2012-10-01

    Full Text Available In today’s global scenario of intense competition and environmental uncertainty flexibility in supply chain has an important role to play for the existence of any supply chain business. A need to be responsive to the constantly changing market scenario and cater to the customer needs, a certain degree of flexibility is required, which requires the coordination of many plants to produce and deliver goods to customers located in different places, and suppliers, which provide each plant with the required components. This paper intends to measure the degree of flexibility required for a two stage supply chain and assessing both the supplier flexibility and the assembler flexibility. In this paper, nine configurations of the SC are considered resulting from the combination of the three degrees of supplier and manufacturer flexibility, i.e. no flexibility, limited flexibility and total flexibility, respectively. Simulation model representing the different flexibility configurations are evaluated and the performance of each configuration analyzed to determine the flexibility configuration suitable to a supply chain. In particular the performance analysis of lead time, work-in-process, service level and cost are measured to determine the suitable flexibility.

  6. Hibernating black bears (Ursus americanus) experience skeletal muscle protein balance during winter anorexia.

    Science.gov (United States)

    Lohuis, T D; Harlow, H J; Beck, T D I

    2007-05-01

    Black bears spend four to seven months every winter confined to their den and anorexic. Despite potential for skeletal muscle atrophy and protein loss, bears appear to retain muscle integrity throughout winter dormancy. Other authors have suggested that bears are capable of net protein anabolism during this time. The present study was performed to test this hypothesis by directly measuring skeletal muscle protein metabolism during the summer, as well as early and late hibernation periods. Muscle biopsies were taken from the vastus lateralis of six free-ranging bears in the summer, and from six others early in hibernation and again in late winter. Protein synthesis and breakdown were measured on biopsies using (14)C-phenylalanine as a tracer. Muscle protein, nitrogen, and nucleic acid content, as well as nitrogen stable isotope enrichment, were also measured. Protein synthesis was greater than breakdown in summer bears, suggesting that they accumulate muscle protein during periods of seasonal food availability. Protein synthesis and breakdown were both lower in winter compared to summer but were equal during both early and late denning, indicating that bears are in protein balance during hibernation. Protein and nitrogen content, nucleic acid, and stable isotope enrichment measurements of the biopsies support this conclusion.

  7. A Hybrid Fuzzy Model for Lean Product Development Performance Measurement

    Science.gov (United States)

    Osezua Aikhuele, Daniel; Mohd Turan, Faiz

    2016-02-01

    In the effort for manufacturing companies to meet up with the emerging consumer demands for mass customized products, many are turning to the application of lean in their product development process, and this is gradually moving from being a competitive advantage to a necessity. However, due to lack of clear understanding of the lean performance measurements, many of these companies are unable to implement and fully integrated the lean principle into their product development process. Extensive literature shows that only few studies have focus systematically on the lean product development performance (LPDP) evaluation. In order to fill this gap, the study therefore proposed a novel hybrid model based on Fuzzy Reasoning Approach (FRA), and the extension of Fuzzy-AHP and Fuzzy-TOPSIS methods for the assessment of the LPDP. Unlike the existing methods, the model considers the importance weight of each of the decision makers (Experts) since the performance criteria/attributes are required to be rated, and these experts have different level of expertise. The rating is done using a new fuzzy Likert rating scale (membership-scale) which is designed such that it can address problems resulting from information lost/distortion due to closed-form scaling and the ordinal nature of the existing Likert scale.

  8. Measuring the impact of HRM on organizational performance

    Directory of Open Access Journals (Sweden)

    Anastasia A. Katou

    2008-12-01

    Full Text Available Normal 0 21 false false false ES ZH-CN X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman","serif"; mso-ansi-language:ES-TRAD; mso-fareast-language:EN-US;} The purpose of this paper is to measure the impact of HRM on organisational performance in the context of Greece. Data were collected from 178 organisations using a questionnaire survey in the Greek manufacturing sector, and analysed using the ‘structural equation modelling’ methodology. The results indicated that the relationship between HRM policies (resourcing and development, compensation and incentives, involvement and job design and organisational performance is partially mediated through HRM outcomes (skills, attitudes, behaviour, and it is influenced by business strategies (cost, quality, innovation. Thus, the contribution of this study for academics and practitioners is that HRM policies associated with business strategies will affect organisational performance through HRM outcomes.

  9. Analysis of ESG indicators for measuring enterprise performance

    Directory of Open Access Journals (Sweden)

    Zuzana Chvátalová

    2013-01-01

    Full Text Available In this article authors focus on the analysis of the whole set of environmental, social and corporate governance (ESG indicators for the elimination of double or triple effects within the next construction of methods for measuring corporate performance. They build on their previously published results (in Acta univ. agric. et silvic. Mendel. Brun., 2012. The partial actual selected results of a recently undertaken currently project entitled ‘Construction of Methods for Multifactorial Assessment of Company Complex Performance in Selected Sectors’ were used. This project was solved the research teams of the Faculty of Business and Management of Brno University Technology and Faculty of Business and Economics of Mendel University in Brno since 2011. Further theoretical resources in the environmental, social and corporate governance area, known indicator databases (namely Global Reporting Initiative, comparative analysis, resp. syntheses for identifying possible of common indicator properties were identified to classify indicator subsets to preclude double or even triple effect based on mathematical set theory (Venn diagrams. The indicator analysis in constructed multi-factorial methods contributes to precise decision making in management to improve corporate performance.

  10. Measuring performance improvement: total organizational commitment or clinical specialization.

    Science.gov (United States)

    Caron, Aleece; Jones, Paul; Neuhauser, Duncan; Aron, David C

    2004-01-01

    Resources for hospitals are limited when they are faced with multiple publicly reported performance measures as tools to assess quality. The leadership in these organizations may choose to focus on 1 or 2 of these outcomes. An alternative approach is that the leadership may commit resources or create conditions that result in improved quality over a broad range of measures. We used aggregated data on mortality, length of stay, and obstetrical outcomes from Greater Cleveland Health Quality Choice data to test these theories. We used Pearson correlation analysis to determine of outcomes were correlated with one another. We used repeated-measures ANOVA to determine if an association existed between outcome and time and outcome and hospital. All of the outcomes across all hospitals demonstrate a trend of overall improvement. Both the Pearson and ANOVA result support the hypothesis for the organization-wide approach to quality improvement. Hospital that make improvements in one clinical area trend to make improvements in others. Hospitals that produce improvements in limited clinical or administrative areas may not have completely adopted CQI into their culture or may not have yet realized the benefits of their organizational commitments, but use some of the concepts to improve quality outcomes.

  11. Effect of altitude on solar UVR and spectral and spatial variations of UV irradiances measured inWagrain, Austria in winter

    DEFF Research Database (Denmark)

    Baczynska, Katarzyna A; Pearson, Andy J; O'Hagan, John B

    2013-01-01

    Ultraviolet radiation spectral irradiance was measured at different altitudes on horizontal and tilted planes in different azimuth directions on cloudless days in Austria, in March 2010, within the Impact of Climatic and Environmental factors on Personal Ultraviolet Radiation Exposure project...

  12. Resources on work zone safety and mobility performance monitoring and measurement.

    Science.gov (United States)

    2013-01-01

    Work zone performance measures are metrics that help quantify how work zones impact travelers, residents, businesses, and workers. Some performance measures describe how an individual work zone impacts these audiences; other performance measures desc...

  13. Developing safety performance functions incorporating reliability-based risk measures.

    Science.gov (United States)

    Ibrahim, Shewkar El-Bassiouni; Sayed, Tarek

    2011-11-01

    Current geometric design guides provide deterministic standards where the safety margin of the design output is generally unknown and there is little knowledge of the safety implications of deviating from these standards. Several studies have advocated probabilistic geometric design where reliability analysis can be used to account for the uncertainty in the design parameters and to provide a risk measure of the implication of deviation from design standards. However, there is currently no link between measures of design reliability and the quantification of safety using collision frequency. The analysis presented in this paper attempts to bridge this gap by incorporating a reliability-based quantitative risk measure such as the probability of non-compliance (P(nc)) in safety performance functions (SPFs). Establishing this link will allow admitting reliability-based design into traditional benefit-cost analysis and should lead to a wider application of the reliability technique in road design. The present application is concerned with the design of horizontal curves, where the limit state function is defined in terms of the available (supply) and stopping (demand) sight distances. A comprehensive collision and geometric design database of two-lane rural highways is used to investigate the effect of the probability of non-compliance on safety. The reliability analysis was carried out using the First Order Reliability Method (FORM). Two Negative Binomial (NB) SPFs were developed to compare models with and without the reliability-based risk measures. It was found that models incorporating the P(nc) provided a better fit to the data set than the traditional (without risk) NB SPFs for total, injury and fatality (I+F) and property damage only (PDO) collisions. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Changes in Handset Performance Measures due to Spherical Radiation Pattern Measurement Uncertainty

    DEFF Research Database (Denmark)

    Nielsen, Jesper Ødum; Pedersen, Gert Frølund

    An important characteristic of a mobile handset is its ability to receive and transmit power. One way to characterize the performance of a handset in this respect is to use measurements of the spherical radiation pattern from which the total radiated power (TRP), total isotropic sensitivity (TIS)...... with respect to the environment. Standard deviations up to about 0.5dB and a maximum deviation of about 1.6dB were found....... in the performance measures are investigated for both the GSM-900 and the GSM-1800 band. Despite the deliberately large deviations from the reference position, the changes in TRP and TIS are generally within ±0.5dB with a maximum of about 1.4dB. For the MEG values the results depend on the orientation of the handset...... system that may introduce errors in standardized performance measurements. Radiation patterns of six handsets have been measured while they were mounted at various offsets from the reference position defined by the Cellular Telecommunications & Internet Association (CTIA) certification. The change...

  15. Electron Identification Performance and First Measurement of $W \\to e + \

    CERN Document Server

    Ueno, Rynichi

    2010-01-01

    The identification of electrons is important for the ATLAS experiment because electrons are present in many interactions of interest produced at the Large Hadron Collider. A deep knowledge of the detector, the electron identification algorithms, and the calibration techniques are crucial in order to accomplish this task. This thesis work presents a Monte Carlo study using electrons from the W —> e + v process to evaluate the performance of the ATLAS electromagnetic calorimeter. A significant number of electrons was produced in the early ATLAS collision runs at centre-of-mass energies of 900 GeV and 7 TeV between November 2009 and April 2010, and their properties are presented. Finally, a first measurement of W —> e + v process with the ATLAS experiment was successfully accomplished with the first C = 1.0 nb_ 1 of data at the 7 TeV collision energy, and the properties of the W candidates are also detailed.

  16. Performance Measurement of Mining Equipments by Utilizing OEE

    Directory of Open Access Journals (Sweden)

    Sermin Elevli

    2010-10-01

    Full Text Available Over the past century, open pit mines have steadily increased their production rate by using larger equipments which requireintensive capital investment. Low commodity prices have forced companies to decrease their unit cost by improving productivity. Oneway to improve productivity is to utilize equipment as effectively as possible. Therefore, the accurate estimation of equipmenteffectiveness is very important so that it can be increased. Overall Equipment Effectiveness (OEE is a well-known measurementmethod, which combines availability, performance and quality, for the evaluation of equipment effectiveness in manufacturing industry.However, there isn’t any study in literature about how to use this metric for mining equipments such as shovel, truck, drilling machineetc. This paper will discuss the application of OEE to measure effectiveness of mining equipment. It identifies causes of time losses forshovel and truck operations and introduces procedure to record time losses. The procedure to estimate OEE of shovels and trucks hasalso been presented via numerical example.

  17. Application Of Quality Function Deployment (QFD) To Measure Performance

    International Nuclear Information System (INIS)

    Fazila Said; Mohd Amirul Shafiq Shafiee; Nurul Hasanah Mohd Abd Basir

    2014-01-01

    This study aims to measure service quality performance and identify critical service quality characteristics as perceived by the customers. An integrated results survey that conducted by seven service centers that certified with Quality Management System (QMS) in Nuclear Malaysia are analysed. This is followed by constructing House of Quality (HoQ) and identifying other parameters for the Quality Function Deployment (QFD) matrix. HoQ is a simple and attractive service innovation tool which can be used to directly show comprehensive information which contained the voice of customer (VOC), technical response, technical correlation and matrix relationship. This study revealed that the information's from HoQ with further discussion on planning part which can be used to assist management in knowing the overall detail information of service center achievement and recognizes the solution for unsatisfied customer through priority improvement activity to enhance the customer satisfaction in future. (author)

  18. Integrating patient satisfaction into performance measurement to meet improvement challenges.

    Science.gov (United States)

    Smith, J E; Fisher, D L; Endorf-Olson, J J

    2000-05-01

    A Value Compass has been proposed to guide health care data collection. The "compass corners" represent the four types of data needed to meet health care customer expectations: appropriate clinical outcomes, improved functional status, patient satisfaction, and appropriate costs. Collection of all four types of data is necessary to select processes in need of improvement, guide improvement teams, and monitor the success of improvement efforts. INTEGRATED DATA AT BRYANLGH: BryanLGH Medical Center in Lincoln, Nebraska, has adopted multiple performance measurement systems to collect clinical outcome, financial, and patient satisfaction data into integrated databases. Data integration allows quality professionals at BryanLGH to identify quality issues from multiple perspectives and track the interrelated effects of improvement efforts. A CASE EXAMPLE: Data from the fourth quarter of 1997 indicated the need to improve processes related to cesarean section (C-section) deliveries. An interdisciplinary team was formed, which focused on educating nurses, physicians, and the community about labor support measures. Physicians were given their own rates of C-section deliveries. The C-section rate decreased from 27% to 19%, but per-case cost increased. PickerPLUS+ results indicated that BryanLGH obstetric patients reported fewer problems with receiving information than the Picker norm, but they reported more problems with the involvement of family members and friends. The data collected so far have indicated a decrease in the C-section rate and a need to continue to work on cost and psychosocial issues. A complete analysis of results was facilitated by integrated performance management systems. Successes have been easily tracked over time, and the need for further work on related processes has been clearly identified.

  19. Methodologies for Measuring Judicial Performance: The Problem of Bias

    Directory of Open Access Journals (Sweden)

    Jennifer Elek

    2014-12-01

    Full Text Available Concerns about gender and racial bias in the survey-based evaluations of judicial performance common in the United States have persisted for decades. Consistent with a large body of basic research in the psychological sciences, recent studies confirm that the results from these JPE surveys are systematically biased against women and minority judges. In this paper, we explain the insidious manner in which performance evaluations may be biased, describe some techniques that may help to reduce expressions of bias in judicial performance evaluation surveys, and discuss the potential problem such biases may pose in other common methods of performance evaluation used in the United States and elsewhere. We conclude by highlighting the potential adverse consequences of judicial performance evaluation programs that rely on biased measurements. Durante décadas ha habido una preocupación por la discriminación por género y racial en las evaluaciones del rendimiento judicial basadas en encuestas, comunes en Estados Unidos. De acuerdo con un gran corpus de investigación básica en las ciencias psicológicas, estudios recientes confirman que los resultados de estas encuestas de evaluación del rendimiento judicial están sistemáticamente sesgados contra las mujeres y los jueces de minorías. En este artículo se explica la manera insidiosa en que las evaluaciones de rendimiento pueden estar sesgadas, se describen algunas técnicas que pueden ayudar a reducir las expresiones de sesgo en los estudios de evaluación del rendimiento judicial, y se debate el problema potencial que estos sesgos pueden plantear en otros métodos comunes de evaluación del rendimiento utilizados en Estados Unidos y otros países. Se concluye destacando las posibles consecuencias adversas de los programas de evaluación del rendimiento judicial que se basan en mediciones sesgadas. DOWNLOAD THIS PAPER FROM SSRN: http://ssrn.com/abstract=2533937

  20. Winter fuels report

    Energy Technology Data Exchange (ETDEWEB)

    1995-01-13

    The Winter Fuels Report is intended to provide concise, timely information to the industry, the press, policymakers, consumers, analysts, and State and local governments on the following topics: distillate fuel oil net production, imports and stocks on a US level and for all Petroleum Administration for Defense Districts (PADD) and product supplied on a US level; propane net production, imports and stocks on a US level and for PADD`s I, II, and III; natural gas supply and disposition and underground storage for the US and consumption for all PADD`s, as well as selected National average prices; residential and wholesale pricing data for heating oil and propane for those States participating in the joint Energy Information Administration (EIA)/State Heating Oil and Propane Program; crude oil and petroleum price comparisons for the US and selected cities; and a 6-10 day, 30-Day, and 90-Day outlook for temperature and precipitation and US total heating degree-days by city.

  1. Klaus Winter (1930 - 2015)

    CERN Multimedia

    2015-01-01

    We learned with great sadness that Klaus Winter passed away on 9 February 2015, after a long illness.   Klaus was born in 1930 in Hamburg, where he obtained his diploma in physics in 1955. From 1955 to 1958 he held a scholarship at the Collège de France, where he received his doctorate in nuclear physics under the guidance of Francis Perrin. Klaus joined CERN in 1958, where he first participated in experiments on π+ and K0 decay properties at the PS, and later became the spokesperson of the CHOV Collaboration at the ISR. Starting in 1976, his work focused on experiments with the SPS neutrino beam. In 1984 he joined Ugo Amaldi to head the CHARM experiment, designed for detailed studies of the neutral current interactions of high-energy neutrinos, which had been discovered in 1973 using the Gargamelle bubble chamber at the PS. The unique feature of the detector was its target calorimeter, which used large Carrara marble plates as an absorber material. From 1984 to 1991, Klau...

  2. Winter fuels report

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-04

    The Winter Fuels Report is intended to provide concise, timely information to the industry, the press, policymakers, consumers, analysts, and state and local governments on the following topics: distillate fuel oil net production, imports and stocks for all PADD's and product supplied on a US level; propane net production, imports and stocks for Petroleum Administration for Defense Districts (PADD) I, II, and III; natural gas supply and disposition, underground storage, and consumption for all PADD's; residential and wholesale pricing data for propane and heating oil for those states participating in the joint Energy Information Administration (EIA)/State Heating Oil and Propane Program; crude oil price comparisons for the United States and selected cities; and US total heating degree-days by city. This report will be published weekly by the EIA starting the first week in October 1990 and will continue until the first week in April 1991. The data will also be available electronically after 5:00 p.m. on Thursday during the heating season through the EIA Electronic Publication System (EPUB). 12 tabs.

  3. Measuring the relative performance of stock market using TOPSIS

    Directory of Open Access Journals (Sweden)

    Abolfazl Danaei

    2013-01-01

    Full Text Available For many years, investors used some basic financial ratios to measure the relative performance of various active industries based on two-digit ISIC classification. However, direct implementation of basic financial figures may not be practical in today's business environment since investors face with different criteria. The proposed model of this paper uses Technique for Order Preference by Similarity to Ideal Solution (TOPSIS to compare 37 various industries based on different financial figures. We gather the necessary data over the period of 2009-2010 from Tehran Stock Exchange and investigate the data in two stages. In the first stage, we perform fundamental analysis to select the most appropriate firms and the in the second stage, we use TOPSIS to rank selected firms based on different criteria. The results of the study confirm that information and communication technology, which is one of the biggest firms in this exchange is considered as the best option (relative ranking 0.88 in two years followed by some Cement industry (with relative ranking of 0.26 in 2009 and 0.19 in 2010 and oil refinery units (with relative ranking of 0.23 in 2009 and 0.19 in 2010. The figure also shows that other firms maintain low ratios varied from 0.23 to 0.01. The lowest industry ranking belongs to marine industry.

  4. Verifax: Biometric instruments measuring neuromuscular disorders/performance impairments

    Science.gov (United States)

    Morgenthaler, George W.; Shrairman, Ruth; Landau, Alexander

    1998-01-01

    VeriFax, founded in 1990 by Dr. Ruth Shrairman and Mr. Alex Landau, began operations with the aim of developing a biometric tool for the verification of signatures from a distance. In the course of developing this VeriFax Autograph technology, two other related applications for the technologies under development at VeriFax became apparent. The first application was in the use of biometric measurements as clinical monitoring tools for physicians investigating neuromuscular diseases (embodied in VeriFax's Neuroskill technology). The second application was to evaluate persons with critical skills (e.g., airline pilots, bus drivers) for physical and mental performance impairments caused by stress, physiological disorders, alcohol, drug abuse, etc. (represented by VeriFax's Impairoscope prototype instrument). This last application raised the possibility of using a space-qualified Impairoscope variant to evaluate astronaut performance with respect to the impacts of stress, fatigue, excessive workload, build-up of toxic chemicals within the space habitat, etc. The three applications of VeriFax's patented technology are accomplished by application-specific modifications of the customized VeriFax software. Strong commercial market potentials exist for all three VeriFax technology applications, and market progress will be presented in more detail below.

  5. Positive associations between physical and cognitive performance measures in fibromyalgia.

    Science.gov (United States)

    Cherry, Barbara J; Zettel-Watson, Laura; Chang, Jennifer C; Shimizu, Renee; Rutledge, Dana N; Jones, C Jessie

    2012-01-01

    To investigate the associations between perceived physical function (self-report) and physical and cognitive performance (objective assessments) in persons with fibromyalgia (FM). Correlational study. Exercise testing laboratory in Southern California. Community-residing ambulatory adults meeting the American College of Rheumatology 1990 criteria for FM (N=68; mean age, 59.5y). Not applicable. Composite Physical Function scale, Senior Fitness Test (3 items), Fullerton Advanced Balance scale, 30-foot walk, Trail Making Test parts A and B, Digit Symbol Substitution Test, a composite score of these 3 cognitive measures, attention/executive function composite, processing speed composite, problem solving, inhibition, and episodic memory composite. Hierarchical regression analyses showed that after controlling for age and FM symptoms, better physical performance (based on assessments, not self-report) was associated with higher cognitive function in attention/executive function, processing speed, problem solving, and inhibition. Researchers should continue to investigate the relationship between physical and cognitive function in both clinical and nonclinical populations, as well as explore changes across time. Because physical activity has been associated with neural improvements, further research may identify whether particular mechanisms, such as neurogenesis, synaptogenesis, or changes in inflammatory marker levels, are involved. Copyright © 2012 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  6. THE DEVELOPMENT OF A PERFORMANCE MEASUREMENT SYSTEM FOR MAINTENANCE

    Directory of Open Access Journals (Sweden)

    J.K. Visser

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Business enterprises are under increasing pressure to become internationally competitive due to globalisation. World-class companies from abroad can now easily compete with local companies, introducing high quality products and services to the local community and industry. The pace of technological change is also forcing companies to increase productivity and to become more cost effective. Performance management is part of the strategic management process in the business enterprise and the maintenance department therefore has to address this as part of the strategy formulation for the maintenance function. This paper outlines the strategic management process that is required in the maintenance department and defines a systematic process to develop a performance measurement system for maintenance.

    AFRIKAANSE OPSOMMING: Besigheidsondernemings is onder toenemende druk om internasionaal kompeterend te word weens globalisering. Wêreldklas maatskappye kan nou maklik met plaaslike maatskappye meeding deur hoë kwaliteit produkte en dienste aan die plaaslike gemeenskap en nywerheid te lewer. Die tempo van tegnologiese verandering dwing maatskappye ook om produktiwiteit te verhoog en meer koste-effektief te word. Prestasiebestuur is deel van strategiese bestuur in 'n onderneming en die instandhoudingsafdeling moet derhalwe prestasiebestuur aanspreek as deel van die ontwikkeling van strategie vir die instandhoudingsfunksie. Hierdie artikel bespreek die strategiese bestuursproses soos benodig in die instandhoudingsafdeling en stel 'n sistematiese proses voor vir die ontwikkeling van 'n prestasiemetingstelsel vir instandhouding.

  7. Perform Thermodynamics Measurements on Fuel Cycle Case Study Systems

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Leigh R. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-09-01

    This document was prepared to meet FCR&D level 3 milestone M3FT-14IN0304022, “Perform Thermodynamics Measurements on Fuel Cycle Case Study Systems.” This work was carried out under the auspices of the Thermodynamics and Kinetics FCR&D work package. This document reports preliminary work in support of determining the thermodynamic parameters for the ALSEP process. The ALSEP process is a mixed extractant system comprised of a cation exchanger 2-ethylhexyl-phosphonic acid mono-2-ethylhexyl ester (HEH[EHP]) and a neutral solvating extractant N,N,N’,N’-tetraoctyldiglycolamide (TODGA). The extractant combination produces complex organic phase chemistry that is challenging for traditional measurement techniques. To neutralize the complexity, temperature dependent solvent extraction experiments were conducted with neat TODGA and scaled down concentrations of the ALSEP formulation to determine the enthalpies of extraction for the two conditions. A full set of thermodynamic data for Eu, Am, and Cm extraction by TODGA from 3.0 M HNO3 is reported. These data are compared to previous extraction results from a 1.0 M HNO3 aqueous medium, and a short discussion of the mixed HEH[EHP]/TODGA system results is offered.

  8. E-Area Performance Assessment Interim Measures Assessment FY2005

    Energy Technology Data Exchange (ETDEWEB)

    Stallings, M

    2006-01-31

    After major changes to the limits for various disposal units of the E-Area Low Level Waste Facility (ELLWF) last year, no major changes have been made during FY2005. A Special Analysis was completed which removes the air pathway {sup 14}C limit from the Intermediate Level Vault (ILV). This analysis will allow the disposal of reactor moderator deionizers which previously had no pathway to disposal. Several studies have also been completed providing groundwater transport input for future special analyses. During the past year, since Slit Trenches No.1 and No.2 were nearing volumetric capacity, they were operationally closed under a preliminary closure analysis. This analysis was performed using as-disposed conditions and data and showed that concrete rubble from the demolition of 232-F was acceptable for disposal in the STs even though the latest special analysis for the STs had reduced the tritium limits so that the inventory in the rubble exceeded limits. A number of special studies are planned during the next years; perhaps the largest of these will be revision of the Performance Assessment (PA) for the ELLWF. The revision will be accomplished by incorporating special analyses performed since the last PA revision as well as revising analyses to include new data. Projected impacts on disposal limits of more recent studies have been estimated. No interim measures will be applied during this year. However, it is being recommended that tritium disposals to the Components-in-Grout (CIG) Trenches be suspended until a limited Special Analysis (SA) currently in progress is completed. This SA will give recommendations for optimum placement of tritiated D-Area tower waste. Further recommendations for tritiated waste placement in the CIG Trenches will be given in the upcoming PA revision.

  9. Severe red spruce winter injury in 2003 creates unusual ecological event in the northeastern United States

    Science.gov (United States)

    Brynne E. Lazarus; Paul G. Schaberg; Donald H. DeHayes; Gary J. Hawley

    2004-01-01

    Abundant winter injury to the current-year (2002) foliage of red spruce (Picea rubens Sarg.) became apparent in the northeastern United States in late winter of 2003. To assess the severity and extent of this damage, we measured foliar winter injury at 28 locations in Vermont and surrounding states and bud mortality at a subset of these sites. Ninety percent of all...

  10. Desempenho operacional de semeadura-adubadora em diferentes manejos da cobertura e da velocidade Operational performance of seeder in different forward speed and winter cover crop management

    Directory of Open Access Journals (Sweden)

    Carlos E. A. Furlani

    2007-08-01

    Full Text Available O presente trabalho teve como objetivo avaliar o desempenho de uma semeadora-adubadora no sistema plantio direto. Os fatores estudados foram três manejos das culturas de cobertura, selecionados em função do tamanho de fragmentos da vegetação, triturador de palhas (palha totalmente triturada, roçadora (palha parcialmente picada e rolo-facas (palha acamada, combinados com três velocidades do conjunto trator-semeadora-adubadora, sendo 4,0; 5,0 e 6,0 km h-1. O delineamento experimental foi em blocos casualizados, em esquema fatorial 3 x 3, com nove tratamentos e oito repetições, totalizando 72 observações. Para comparar os tratamentos, avaliaram-se a capacidade de campo operacional, a força de tração e a potência na barra, o consumo horário e por área, e a patinagem dos rodados do trator. O desempenho da semeadora-adubadora não foi influenciado pelos três manejos na cultura de cobertura vegetal. O aumento da velocidade provocou diminuição da força de tração, sendo o inverso para a capacidade de campo operacional e a potência na barra. O consumo horário de combustível aumentou com a velocidade, enquanto o operacional diminuiu.The present work aimed to evaluate the seeder performance in the direct sowing system. The studied factors were three cover crop managements, chosen according to the size of the vegetation fragment, such as straw (straw totally triturated, weeder (straw partially chopped and knife-rolls (straw practically entire, combined with three speeds of the seeder, being 4.0; 5.0 and 6.0 km h-1. The experimental outlining was carried out in casual blocks in factorial scheme 3 x 3, with nine treatments and eight repetitions, totalizing 72 observations. In the course of the experiment the following variants were evaluated: effective field capacity, force and power in the bar, hourly and area consumption of fuel and tractor’s pulleys sliding. The data reached were tabulated and submitted to factorial variant

  11. Evaluation of emergency department performance - a systematic review on recommended performance and quality-in-care measures.

    Science.gov (United States)

    Sørup, Christian Michel; Jacobsen, Peter; Forberg, Jakob Lundager

    2013-08-09

    Evaluation of emergency department (ED) performance remains a difficult task due to the lack of consensus on performance measures that reflects high quality, efficiency, and sustainability. To describe, map, and critically evaluate which performance measures that the published literature regard as being most relevant in assessing overall ED performance. Following the PRISMA guidelines, a systematic literature review of review articles reporting accentuated ED performance measures was conducted in the databases of PubMed, Cochrane Library, and Web of Science. Study eligibility criteria includes: 1) the main purpose was to discuss, analyse, or promote performance measures best reflecting ED performance, 2) the article was a review article, and 3) the article reported macro-level performance measures, thus reflecting an overall departmental performance level. A number of articles addresses this study's objective (n = 14 of 46 unique hits). Time intervals and patient-related measures were dominant in the identified performance measures in review articles from US, UK, Sweden and Canada. Length of stay (LOS), time between patient arrival to initial clinical assessment, and time between patient arrivals to admission were highlighted by the majority of articles. Concurrently, "patients left without being seen" (LWBS), unplanned re-attendance within a maximum of 72 hours, mortality/morbidity, and number of unintended incidents were the most highlighted performance measures that related directly to the patient. Performance measures related to employees were only stated in two of the 14 included articles. A total of 55 ED performance measures were identified. ED time intervals were the most recommended performance measures followed by patient centeredness and safety performance measures. ED employee related performance measures were rarely mentioned in the investigated literature. The study's results allow for advancement towards improved performance measurement and

  12. Diagnostic performance of MRI measurements to assess hindfoot malalignment. An assessment of four measurement techniques

    International Nuclear Information System (INIS)

    Buck, Florian M.; Hoffmann, Adrienne; Mamisch-Saupe, Nadja; Hodler, Juerg; Farshad, Mazda; Espinosa, Norman; Resnick, Donald

    2013-01-01

    To investigate the ability of coronal non-weight-bearing MR images to discriminate between normal and abnormal hindfoot alignment. Three different measurement techniques (calcaneal axis, medial/lateral calcaneal contour) based on weight-bearing hindfoot alignment radiographs were applied in 49 patients (mean, 48 years; range 21-76 years). Three groups of subjects were enrolled: (1) normal hindfoot alignment (0 -10 valgus); (2) abnormal valgus (>10 ); (3) any degree of varus hindfoot alignment. Hindfoot alignment was then measured on coronal MR images using four different measurement techniques (calcaneal axis, medial/lateral calcaneal contour, sustentaculum tangent). ROC analysis was performed to find the MR measurement with the greatest sensitivity and specificity for discrimination between normal and abnormal hindfoot alignment. The most accurate measurement on MR images to detect abnormal hindfoot valgus was the one using the medial calcaneal contour, reaching a sensitivity/specificity of 86 %/75 % using a cutoff value of >11 valgus. The most accurate measurement on MR images to detect abnormal hindfoot varus was the sustentaculum tangent, reaching a sensitivity/specificity of 91 %/71 % using a cutoff value of <12 valgus. It is possible to suspect abnormal hindfoot alignment on coronal non-weight-bearing MR images. (orig.)

  13. Diagnostic performance of MRI measurements to assess hindfoot malalignment. An assessment of four measurement techniques

    Energy Technology Data Exchange (ETDEWEB)

    Buck, Florian M.; Hoffmann, Adrienne; Mamisch-Saupe, Nadja; Hodler, Juerg [University Hospital Balgrist and University of Zurich, Radiology, Zuerich (Switzerland); Farshad, Mazda; Espinosa, Norman [University Hospital Balgrist and University of Zurich, Department of Orthopaedic Surgery, Zuerich (Switzerland); Resnick, Donald [University of California San Diego, Department of Radiology, San Diego, CA (United States)

    2013-09-15

    To investigate the ability of coronal non-weight-bearing MR images to discriminate between normal and abnormal hindfoot alignment. Three different measurement techniques (calcaneal axis, medial/lateral calcaneal contour) based on weight-bearing hindfoot alignment radiographs were applied in 49 patients (mean, 48 years; range 21-76 years). Three groups of subjects were enrolled: (1) normal hindfoot alignment (0 -10 valgus); (2) abnormal valgus (>10 ); (3) any degree of varus hindfoot alignment. Hindfoot alignment was then measured on coronal MR images using four different measurement techniques (calcaneal axis, medial/lateral calcaneal contour, sustentaculum tangent). ROC analysis was performed to find the MR measurement with the greatest sensitivity and specificity for discrimination between normal and abnormal hindfoot alignment. The most accurate measurement on MR images to detect abnormal hindfoot valgus was the one using the medial calcaneal contour, reaching a sensitivity/specificity of 86 %/75 % using a cutoff value of >11 valgus. The most accurate measurement on MR images to detect abnormal hindfoot varus was the sustentaculum tangent, reaching a sensitivity/specificity of 91 %/71 % using a cutoff value of <12 valgus. It is possible to suspect abnormal hindfoot alignment on coronal non-weight-bearing MR images. (orig.)

  14. Assessing winter cover crop nutrient uptake efficiency using a water quality simulation model

    Science.gov (United States)

    Yeo, I.-Y.; Lee, S.; Sadeghi, A. M.; Beeson, P. C.; Hively, W. D.; McCarty, G. W.; Lang, M. W.

    2014-12-01

    Winter cover crops are an effective conservation management practice with potential to improve water quality. Throughout the Chesapeake Bay watershed (CBW), which is located in the mid-Atlantic US, winter cover crop use has been emphasized, and federal and state cost-share programs are available to farmers to subsidize the cost of cover crop establishment. The objective of this study was to assess the long-term effect of planting winter cover crops to improve water quality at the watershed scale (~ 50 km2) and to identify critical source areas of high nitrate export. A physically based watershed simulation model, Soil and Water Assessment Tool (SWAT), was calibrated and validated using water quality monitoring data to simulate hydrological processes and agricultural nutrient cycling over the period of 1990-2000. To accurately simulate winter cover crop biomass in relation to growing conditions, a new approach was developed to further calibrate plant growth parameters that control the leaf area development curve using multitemporal satellite-based measurements of species-specific winter cover crop performance. Multiple SWAT scenarios were developed to obtain baseline information on nitrate loading without winter cover crops and to investigate how nitrate loading could change under different winter cover crop planting scenarios, including different species, planting dates, and implementation areas. The simulation results indicate that winter cover crops have a negligible impact on the water budget but significantly reduce nitrate leaching to groundwater and delivery to the waterways. Without winter cover crops, annual nitrate loading from agricultural lands was approximately 14 kg ha-1, but decreased to 4.6-10.1 kg ha-1 with cover crops resulting in a reduction rate of 27-67% at the watershed scale. Rye was the most effective species, with a potential to reduce nitrate leaching by up to 93% with early planting at the field scale. Early planting of cover crops (~ 30

  15. Front-End Electronics for Verification Measurements: Performance Evaluation and Viability of Advanced Tamper Indicating Measures

    International Nuclear Information System (INIS)

    Smith, E.; Conrad, R.; Morris, S.; Ramuhalli, P.; Sheen, D.; Schanfein, M.; Ianakiev, K.; Browne, M.; Svoboda, J.

    2015-01-01

    The International Atomic Energy Agency (IAEA) continues to expand its use of unattended, remotely monitored measurement systems. An increasing number of systems and an expanding family of instruments create challenges in terms of deployment efficiency and the implementation of data authentication measures. A collaboration between Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and Los Alamos National Laboratory (LANL) is working to advance the IAEA's capabilities in these areas. The first objective of the project is to perform a comprehensive evaluation of a prototype front-end electronics package, as specified by the IAEA and procured from a commercial vendor. This evaluation begins with an assessment against the IAEA's original technical specifications and expands to consider the strengths and limitations over a broad range of important parameters that include: sensor types, cable types, and the spectrum of industrial electromagnetic noise that can degrade signals from remotely located detectors. A second objective of the collaboration is to explore advanced tamper-indicating (TI) measures that could help to address some of the long-standing data authentication challenges with IAEA's unattended systems. The collaboration has defined high-priority tampering scenarios to consider (e.g., replacement of sensor, intrusion into cable), and drafted preliminary requirements for advanced TI measures. The collaborators are performing independent TI investigations of different candidate approaches: active time-domain reflectometry (PNNL), passive noise analysis (INL), and pulse-by-pulse analysis and correction (LANL). The initial investigations focus on scenarios where new TI measures are retrofitted into existing IAEA UMS deployments; subsequent work will consider the integration of advanced TI methods into new IAEA UMS deployments where the detector is separated from the front-end electronics. In this paper, project progress

  16. Impact of warm winters on microbial growth

    Science.gov (United States)

    Birgander, Johanna; Rousk, Johannes; Axel Olsson, Pål

    2014-05-01

    temperature relationships of the bacterial community from winter-warmed plots and plots with ambient soil temperatures were compared. No change in optimum temperature for growth could be detected, indicating that the microbial community has not been warm-adapted. This fits with what was seen also in the laboratory experiment where no changes in temperature response occurred when exposing bacteria to temperatures below 10 °C within two months. The increase in activity measured during winter should thereby be due to changes in environmental factors, which will be further investigated. One big difference between heated and control plots was that heated plots were snow free during the entire winter, while control plots were covered by a 10 cm snow cover. The plant community composition and flowering time also differed in the warmed and ambient plot.

  17. Freight corridor performance measurement system: A framework for South Africa

    Directory of Open Access Journals (Sweden)

    Jan H. Havenga

    2016-11-01

    Full Text Available Background: On a national level, South Africa’s freight logistics industry is inefficient. The country ranks 36th out of 40 countries in terms of transport productivity (tonne kilometres as a ratio of gross domestic product, or GDP; the ratio of freight logistics costs to GDP measured 11.1% in 2013, compared to that of developed regions which measures in the order of 9%; and rail tonne-km market share on the two most dense long-distance corridors, namely, GautengDurban and Gauteng-Cape Town, is only 12.8% and 4.4%, respectively, whereas rail is globally acknowledged as a more efficient provider of long-distance freight solutions, given appropriate investments and service commitments. Objectives: A cornerstone of improved national freight logistics performance is the availability of reliable indicators to quantify the efficiency and capacity of the logistics network over the intermediate and long term, thereby enabling an evidence-based policy and investment environment. The objective of this article is to describe the foundation framework (i.e. phase 1 for South Africa’s freight corridor performance measurement system (CPMS. Once populated, the CPMS will be a key generator of indicators to facilitate the systemic management of corridors as a national production factor and thereby contributing to South Africa’s competitiveness. Method: The design of South Africa’s CPMS was informed by desktop research and refined through an extensive stakeholder consultation process. A distinction was made between South Africa’s dedicated bulk corridors and the multi-modal corridors. Results: Facilitating both stakeholder involvement and agreement on key indicators, as well as the eventual development of a system supporting the population, aggregation and dissemination of the CPMS are critical outcomes for the management of corridors as a national production factor. Three overarching corridor indicators were defined, relating to increased throughput

  18. Tumescent liposuction report performance measurement initiative: national survey results.

    Science.gov (United States)

    Hanke, William; Cox, Sue Ellen; Kuznets, Naomi; Coleman, William P

    2004-07-01

    This study was created by the Accreditation Association for Ambulatory Health Care Institute for Quality Improvement to measure clinical performance and improvement opportunities for physicians and ambulatory health-care organizations. Data were collected prospectively between February 2001 and August 2002. Thirty-nine study centers participated, and 688 patients who had tumescent liposuction were surveyed and followed for 6 months. The objective was to determine patient satisfaction with tumescent liposuction and examine current liposuction practice and the safety of tumescent liposuction in a representative cohort of patients. The Accreditation Association for Ambulatory Health Care Institute for Quality Improvement collected prospective data from February 2001 to August 2002 from 68 organizations registered for this study. Ultimately 39 organizations submitted 688 useable cases performed totally with local anesthesia, "tumescent technique." The overall clinical complication rate found in the Accreditation Association for Ambulatory Health Care Institute for Quality Improvement study was 0.7% (5 of 702). There was a minor complication rate of 0.57%. The major complication rate was 0.14% with one patient requiring hospitalization. Seventy-five percent of the patients reported no discomfort during their procedures. Of the 59% of patients who responded to a 6-month postoperative survey, 91% were positive about their decision to have liposuction (rating of 4 or 5 on a scale of 1-5) and 84% had high levels (4 or 5 on a scale of 1-5) of overall satisfaction with the procedure. Our findings are consistent with others in that tumescent liposuction is a safe procedure with a low complication rate and high patient satisfaction.

  19. 45 CFR 270.7 - What data will we use to measure performance on the work support and other measures?

    Science.gov (United States)

    2010-10-01

    ... measure performance on the work support and other measures? (a) We will use Census Bureau data to rank... 45 Public Welfare 2 2010-10-01 2010-10-01 false What data will we use to measure performance on the work support and other measures? 270.7 Section 270.7 Public Welfare Regulations Relating to Public...

  20. Upper Bounds on Performance Measures of Heterogeneous // Queues

    Directory of Open Access Journals (Sweden)

    F. S. Q. Alves

    2011-01-01

    Full Text Available In many real-life queueing systems, the servers are often heterogeneous, namely they work at different rates. This paper provides a simple method to compute tight upper bounds on two important performance measures of single-class heterogeneous multi-server Markovian queueing systems, namely the average number in queue and the average waiting time in queue. This method is based on an expansion of the state space that is followed by an approximate reduction of the state space, only considering the most probable states. In most cases tested, we were able to approximate the actual behavior of the system with smaller errors than those obtained from traditional homogeneous multiserver Markovian queues, as shown by GPSS simulations. In addition, we have correlated the quality of the approximation with the degree of heterogeneity of the system, which was evaluated using its Gini index. Finally, we have shown that the bounds are robust and still useful, even considering quite different allocation strategies. A large number of simulation results show the accuracy of the proposed method that is better than that of classical homogeneous multiserver Markovian formulae in many situations.

  1. Measured and projected performance of plasma direct converters

    International Nuclear Information System (INIS)

    Barr, W.L.; Moir, R.W.

    1981-01-01

    Test results from two plasma direct converters and their predicted cost and performance on tandem mirror fusion reactors are present. The tests were done at high power density (approx. 70 W/cm 2 ) in steady state to simulate the predicted conditions in a reactor. A single stage unit and a two-stage unit of the Venetian blind type were tested at up to 100 kV and 6 kW for a total time of about 80 hours. Measured efficiencies, when projected to a reactor, are typically about 50% for a single stage unit and 60 to 70% for a two-stage unit, depending on the energy distribution of the ions, the degree of subdivision of the collectors, and on the gas pressure. The high ambipolar potential in tandem mirror devices makes this good efficiency possible. When radiatively cooled grids are used, the incident power density is limited to about 100 W/cm 2 by the thermionic emission of electrons

  2. Measuring economic performance, social progress and sustainability using an index

    International Nuclear Information System (INIS)

    de Carvalho, Joaquim Francisco

    2011-01-01

    The energy crisis and a greater awareness among the general public regarding the issue of climate change have, between them, led to a notable increase in the interest shown by governments in relation to the problem of environmental sustainability. An example has been the initiative taken by the President of France to set up a commission, known as the Sarkozy Commission, named after the President, bringing together renowned economists to study and propose forms of economic performance measurement related to social progress. This article aims to propose a methodology to establish a quantitative definition of sustainability structured on the principles of minimum and maximum entropy production, and, based on this, outline a way of organizing the many sources of, and kinds of energy, we have available to us in order of the intensity of their respective environmental impacts. Based on this, we could produce an Environmental Sustainability Index, linked to existing statistical indicators of human development, and thereby arrive at a Sustainable Human Development Index, which would be positively or negatively influenced by parameters linked to environmental sustainability and quality of life. In order to ensure that this index can produce practical results, the WTO (World Trade Organization) would have to establish a scale of increments, to be applied to export tariffs on products originating in countries with different indexes. (author)

  3. Winter/Summer Monsoon Experiment

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Winter/Summer Monsoon Experiment (MONEX) was conducted during the First Global GARP (Global Atmospheric Research Program) Experiment (FGGE). An international...

  4. Measurement system performance during cold checkout runs at the BNFP

    International Nuclear Information System (INIS)

    Ehinger, M.H.; Crawford, J.M.

    1978-01-01

    The measurement systems in a complex nuclear fuel plant such as the Barnwell Nuclear Fuel Plant rely on capabilities to remotely measure solution quantities and determine the nuclear material content of these solutions. During recent testing activities using natural uranium, a major objective of the NMC group was to demonstrate these solution measurement capabilities. Installed measurement systems at the BNFP use the most recent innovations in measurement equipment and techniques for remote solution measurement. This paper presents the measurement methods and results of the tests and evaluations. 6 figures

  5. A National Initiative to Advance School Mental Health Performance Measurement in the US

    Science.gov (United States)

    Connors, Elizabeth Halsted; Stephan, Sharon Hoover; Lever, Nancy; Ereshefsky, Sabrina; Mosby, Amanda; Bohnenkamp, Jill

    2016-01-01

    Standardized health performance measurement has increasingly become an imperative for assuring quality standards in national health care systems. As compared to somatic health performance measures, behavioral health performance measures are less developed. There currently is no national standardized performance measurement system for monitoring…

  6. The meaning of nuclear winter

    International Nuclear Information System (INIS)

    Geiger, H.J.

    1987-01-01

    In this paper the author reviews the history and origins of the basic ideas underlying nuclear winter; and findings and predictions of several groups regarding this topic. The author reviews some of the further developments and scientific analyses regarding nuclear winter since the initial announcements of 1983, touching on some of the revisions and controversies and trying to indicate the current status of the field

  7. Numerical simulation of a rare winter hailstorm event over Delhi, India on 17 January 2013

    Science.gov (United States)

    Chevuturi, A.; Dimri, A. P.; Gunturu, U. B.

    2014-12-01

    This study analyzes the cause of the rare occurrence of a winter hailstorm over New Delhi/NCR (National Capital Region), India. The absence of increased surface temperature or low level of moisture incursion during winter cannot generate the deep convection required for sustaining a hailstorm. Consequently, NCR shows very few cases of hailstorms in the months of December-January-February, making the winter hail formation a question of interest. For this study, a recent winter hailstorm event on 17 January 2013 (16:00-18:00 UTC) occurring over NCR is investigated. The storm is simulated using the Weather Research and Forecasting (WRF) model with the Goddard Cumulus Ensemble (GCE) microphysics scheme with two different options: hail and graupel. The aim of the study is to understand and describe the cause of hailstorm event during over NCR with a comparative analysis of the two options of GCE microphysics. Upon evaluating the model simulations, it is observed that the hail option shows a more similar precipitation intensity with the Tropical Rainfall Measuring Mission (TRMM) observation than the graupel option does, and it is able to simulate hail precipitation. Using the model-simulated output with the hail option; detailed investigation on understanding the dynamics of hailstorm is performed. The analysis based on a numerical simulation suggests that the deep instability in the atmospheric column led to the formation of hailstones as the cloud formation reached up to the glaciated zone promoting ice nucleation. In winters, such instability conditions rarely form due to low level available potential energy and moisture incursion along with upper level baroclinic instability due to the presence of a western disturbance (WD). Such rare positioning is found to be lowering the tropopause with increased temperature gradient, leading to winter hailstorm formation.

  8. Winter precipitation characteristics in western US related to atmospheric river landfalls: observations and model evaluations

    Science.gov (United States)

    Kim, J.; Guan, B.; Waliser, D. E.; Ferraro, R. D.; Case, J. L.; Iguchi, T.; Kemp, E.; Putman, W.; Wang, W.; Wu, D.; Tian, B.

    2018-01-01

    Winter precipitation (PR) characteristics in western United States (WUS) related to atmospheric river (AR) landfalls are examined using the observation-based PRISM data. The observed AR-related precipitation characteristics are in turn used to evaluate model precipitation data from the NASA MERRA2 reanalysis and from seven dynamical downscaling simulations driven by the MERRA2. Multiple metrics including mean bias, Taylor diagram, and two skill scores are used to measure model performance for three climatological sub-regions in WUS, Pacific Northwest (PNW), Pacific Southwest (PSW) and Great Basin (GB). All model data well represent the winter-mean PR with spatial pattern correlations of 0.8 or higher with PRISM for the three sub-regions. Higher spatial resolutions and/or the use of spectral nudging generally yield higher skill scores in simulating the geographical distribution of PR for the entire winter. The PRISM data shows that the AR-related fraction of winter PR and associated daily PR PDFs in each region vary strongly for landfall locations; AR landfalls in the northern WUS coast (NC) affect mostly PNW while those in the southern WUS coast (SC) affect both PSW and GB. NC (SC) landfalls increase the frequency of heavy PR in PNW (PSW and GB) but reduce it in PSW (PNW). All model data reasonably represent these observed variations in the AR-related winter PR fractions and the daily PR PDFs according to AR landfall locations. However, unlike for the entire winter period, no systematic effects of resolution and/or spectral nudging are identified in these AR-related PR characteristics. Dynamical downscaling in this study generally yield positive added values to the MERRA2 PR in the AR-related PR fraction for most sub-regions and landfall locations, most noticeably for PSW by NU-WRF. The downscaling also generate positive added value in p95 for PNW, but negative values for PSW and GB due to overestimation of heavy precipitation events.

  9. Numerical simulation of a rare winter hailstorm event over Delhi, India on 17 January 2013

    KAUST Repository

    Chevuturi, A.

    2014-12-19

    This study analyzes the cause of the rare occurrence of a winter hailstorm over New Delhi/NCR (National Capital Region), India. The absence of increased surface temperature or low level of moisture incursion during winter cannot generate the deep convection required for sustaining a hailstorm. Consequently, NCR shows very few cases of hailstorms in the months of December-January-February, making the winter hail formation a question of interest. For this study, a recent winter hailstorm event on 17 January 2013 (16:00–18:00 UTC) occurring over NCR is investigated. The storm is simulated using the Weather Research and Forecasting (WRF) model with the Goddard Cumulus Ensemble (GCE) microphysics scheme with two different options: hail and graupel. The aim of the study is to understand and describe the cause of hailstorm event during over NCR with a comparative analysis of the two options of GCE microphysics. Upon evaluating the model simulations, it is observed that the hail option shows a more similar precipitation intensity with the Tropical Rainfall Measuring Mission (TRMM) observation than the graupel option does, and it is able to simulate hail precipitation. Using the model-simulated output with the hail option; detailed investigation on understanding the dynamics of hailstorm is performed. The analysis based on a numerical simulation suggests that the deep instability in the atmospheric column led to the formation of hailstones as the cloud formation reached up to the glaciated zone promoting ice nucleation. In winters, such instability conditions rarely form due to low level available potential energy and moisture incursion along with upper level baroclinic instability due to the presence of a western disturbance (WD). Such rare positioning is found to be lowering the tropopause with increased temperature gradient, leading to winter hailstorm formation.

  10. The validity of subjective performance measures: school principals in Texas and Denmark

    NARCIS (Netherlands)

    Meier, Kenneth J.; Winter, Soren C.; O'Toole, Laurence J.; Favero, Nathan; Andersen, Simon Calmar

    2015-01-01

    Public management studies are increasingly using survey data on managers' perceptions of performance to measure organizational performance. These perceptual measures are tempting to apply because archival performance data or surveys of target group outcomes and satisfaction are often lacking, costly

  11. Access management performance measures for Virginia : a practical approach for public accountability.

    Science.gov (United States)

    2010-04-01

    In order to develop performance measures to communicate the effect of Virginias access management program, five : tasks were performed: (1) the appropriate literature was reviewed, (2) a catalog of potential performance measures was : developed, (...

  12. Perturbing engine performance measurements to determine optimal engine control settings

    Science.gov (United States)

    Jiang, Li; Lee, Donghoon; Yilmaz, Hakan; Stefanopoulou, Anna

    2014-12-30

    Methods and systems for optimizing a performance of a vehicle engine are provided. The method includes determining an initial value for a first engine control parameter based on one or more detected operating conditions of the vehicle engine, determining a value of an engine performance variable, and artificially perturbing the determined value of the engine performance variable. The initial value for the first engine control parameter is then adjusted based on the perturbed engine performance variable causing the engine performance variable to approach a target engine performance variable. Operation of the vehicle engine is controlled based on the adjusted initial value for the first engine control parameter. These acts are repeated until the engine performance variable approaches the target engine performance variable.

  13. INDICATORS USED FOR THE PERFORMANCE MEASUREMENT OF SUSTAINABLE DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Vladoi Anca Daniela

    2009-05-01

    Full Text Available The development of the environment of a company has a direct influence on its performance and its success. For this reason a company should not only analyze its internal performance, but also the external performance of the business environment and the su

  14. Model for measuring complex performance in an aviation environment

    International Nuclear Information System (INIS)

    Hahn, H.A.

    1988-01-01

    An experiment was conducted to identify models of pilot performance through the attainment and analysis of concurrent verbal protocols. Sixteen models were identified. Novice and expert pilots differed with respect to the models they used. Models were correlated to performance, particularly in the case of expert subjects. Models were not correlated to performance shaping factors (i.e. workload). 3 refs., 1 tab

  15. Measuring US Army medical evacuation: Metrics for performance improvement.

    Science.gov (United States)

    Galvagno, Samuel M; Mabry, Robert L; Maddry, Joseph; Kharod, Chetan U; Walrath, Benjamin D; Powell, Elizabeth; Shackelford, Stacy

    2018-01-01

    The US Army medical evacuation (MEDEVAC) community has maintained a reputation for high levels of success in transporting casualties from the point of injury to definitive care. This work served as a demonstration project to advance a model of quality assurance surveillance and medical direction for prehospital MEDEVAC providers within the Joint Trauma System. A retrospective interrupted time series analysis using prospectively collected data was performed as a process improvement project. Records were reviewed during two distinct periods: 2009 and 2014 to 2015. MEDEVAC records were matched to outcomes data available in the Department of Defense Trauma Registry. Abstracted deidentified data were reviewed for specific outcomes, procedures, and processes of care. Descriptive statistics were applied as appropriate. A total of 1,008 patients were included in this study. Nine quality assurance metrics were assessed. These metrics were: airway management, management of hypoxemia, compliance with a blood transfusion protocol, interventions for hypotensive patients, quality of battlefield analgesia, temperature measurement and interventions, proportion of traumatic brain injury (TBI) patients with hypoxemia and/or hypotension, proportion of traumatic brain injury patients with an appropriate assessment, and proportion of missing data. Overall survival in the subset of patients with outcomes data available in the Department of Defense Trauma Registry was 97.5%. The data analyzed for this study suggest overall high compliance with established tactical combat casualty care guidelines. In the present study, nearly 7% of patients had at least one documented oxygen saturation of less than 90%, and 13% of these patients had no documentation of any intervention for hypoxemia, indicating a need for training focus on airway management for hypoxemia. Advances in battlefield analgesia continued to evolve over the period when data for this study was collected. Given the inherent high

  16. Performance Evaluation of Proportional Fair Scheduling Algorithm with Measured Channels

    DEFF Research Database (Denmark)

    Sørensen, Troels Bundgaard; Pons, Manuel Rubio

    2005-01-01

    subjected to measured channel traces. Specifically, we applied measured signal fading recorded from GSM cell phone users making calls on an indoor wireless office system. Different from reference channel models, these measured channels have much more irregular fading between users, which as we show...

  17. Performing Neutron Cross-Section Measurements at RIA

    International Nuclear Information System (INIS)

    Ahle, L.E.

    2003-01-01

    The Rare Isotope Accelerator (RIA) is a proposed accelerator for the low energy nuclear physics community. Its goal is to understand the natural abundances of the elements heavier than iron, explore the nuclear force in systems far from stability, and study symmetry violation and fundamental physics in nuclei. To achieve these scientific goals, RIA promises to produce isotopes far from stability in sufficient quantities to allow experiments. It would also produce near stability isotopes at never before seen production rates, as much as 10 12 pps. Included in these isotopes are many that are important to stockpile stewardship, such as 87 Y, 146-50 Eu, and 231 Th. Given the expected production rates at RIA and a reasonably intense neutron source, one can expect to make ∼10 μg targets of nuclei with a half-life of ∼1 day. Thus, it will be possible at RIA to obtain experimental information on the neutron cross section for isotopes that have to date only been determined by theory. There are two methods to perform neutron cross-section measurements, prompt and delayed. The prompt method tries to measure each reaction as it happens. The exact technique employed will depend on the reaction of interest, (n,2n), (n,γ), (n,p), etc. The biggest challenge with this method is designing a detector system that can handle the gamma ray background from the target. The delayed method, which is the traditional radiochemistry method for determining the cross-section, irradiates the targets and then counts the reaction products after the fact. While this allows one to avoid the target background, the allowed fraction of target impurities is extremely low. This is especially true for the desired reaction product with the required impurity fraction on the order of 10 -9 . This is particularly problematic for (n,2n) and (n,γ) reactions, whose reaction production cannot be chemically separated from the target. In either case, the first step at RIA to doing these measurements is

  18. Performance measurement of workplace change: in two different cultural contexts

    OpenAIRE

    Chaiwat Riratanaphong

    2014-01-01

    Nowadays, organisations must cope with the pressure of cost reduction and efficiency in order to succeed in a highly competitive business environment. However, drivers to improve social interaction and employee’s performance and as such to contribute to organisational goals and objectives make it necessary to be concerned with other performance criteria as well, such as effectiveness, flexibility, employee satisfaction, productivity and creativity. There is a growing need for performance mana...

  19. Relationship between performance measurements and sale price of ...

    African Journals Online (AJOL)

    Unknown

    The main advantage is that the buyer is purchasing a ram that has been selected for traits of economic importance and is adapted to the specific environment in which it is expected to perform. The aim of this study was to determine the extent to which the performance of animals in a veld-ram club influences the price buyers ...

  20. Analysis of Aptitude, Training, and Job Performance Measures

    Science.gov (United States)

    1982-02-01

    provisions have been made for students with unsatisfactory performance to be " recycled ", that is, to retake a module or part of a course (e.g., 2841, Marine...clear, simple language o questions avoided trivia , and were related to task performance o response choices were parallel and realistic. The assessment