Top-Contact Pentacene-Based Organic Thin Film Transistor (OTFT) with N, N'-Bis(3-Methyl Phenyl)- N, N'-Diphenyl Benzidine (TPD)/Au Bilayer Source-Drain Electrode

Science.gov (United States)

Borthakur, Tribeni; Sarma, Ranjit

2018-01-01

A top-contact Pentacene-based organic thin film transistor (OTFT) with N, N'-Bis (3-methyl phenyl)- N, N'-diphenyl benzidine (TPD)/Au bilayer source-drain electrode is reported. The devices with TPD/Au bilayer source-drain (S-D) electrodes show better performance than the single layer S-D electrode OTFT devices. The field-effect mobility of 4.13 cm2 v-1 s-1, the on-off ratio of 1.86 × 107, the threshold voltage of -4 v and the subthreshold slope of .27 v/decade, respectively, are obtained from the device with a TPD/Au bilayer source-drain electrode.

Ammonia IRMS-TPD study on the distribution of acid sites in mordenite.

Science.gov (United States)

Niwa, Miki; Suzuki, Katsuki; Katada, Naonobu; Kanougi, Tomonori; Atoguchi, Takashi

2005-10-13

Using an IRMS-TPD (temperature programmed desorption) of ammonia, we studied the nature, strength, crystallographic location, and distribution of acid sites of mordenite. In this method, infrared spectroscopy (IR) and mass spectroscopy (MS) work together to follow the thermal behavior of adsorbed and desorbed ammonia, respectively; therefore, adsorbed species were identified, and their thermal behavior was directly connected with the desorption of ammonia during an elevation of temperature. IR-measured TPD of the NH4(+) cation was similar to MS-measured TPD, thus showing the nature of Brønsted acidity. From the behavior of OH bands, it was found that the Brønsted acid sites consisted of two kinds of OH bands at high and low wavenumbers, ascribable to OH bands situated on 12- and 8-member rings (MR) of mordenite structure, respectively. The amount and strength of these Brønsted hydroxyls were measured quantitatively based on a theoretical equation using a curve fitting method. Up to ca. 30% of the exchange degree, NH4(+) was exchanged with Na+ on the 12-MR to arrive at saturation; therefore, in this region, the Brønsted acid site was situated on the large pore of 12-MR. The NH4(+) cation was then exchanged with Na+ on 8-MR, and finally exceeded the amount on 12-MR. In the 99% NH4-mordenite, Brønsted acid sites were located predominantly on the 8-MR more than on the 12-MR. Irrespective of the NH4(+) exchange degree, the strengths deltaH of Brønsted OH were 145 and 153 kJ mol(-1) on the 12- and 8-MR, respectively; that is, the strength of Brønsted acid site on the 8-MR was larger than that on the 12-MR. A density functional theory (DFT) calculation supported the difference in the strengths of the acid sites. Catalytic cracking activity of the Brønsted acid sites on the 8-MR declined rapidly, while that on the 12-MR was remarkably kept. The difference in strength and/or steric capacity may cause such a difference in the life of a catalyst.

Study of the irradiation effects on thorium phosphate diphosphate (β-TPD): consequences on its chemical durability

International Nuclear Information System (INIS)

Tamain, C.

2005-12-01

Since Thorium Phosphate Diphosphate (beta-TPD) can be considered as a potential host matrix for long-term storage in underground repository, it is necessary to study the irradiation effects on the structure of this ceramics and the consequences on its chemical durability. Sintered samples of beta-TPD and of associated solid solutions of beta-TUPD were irradiated under ion beams and then altered in aqueous solutions. Depending on the electronic LET value, beta-TPD can be completely or partly amorphized. Furthermore, the ability of recrystallization of the amorphous material by thermal annealing was also demonstrated. Some leaching tests, realized on these irradiated samples, have shown a significant effect of the amorphous fraction on the normalized dissolution rate which was increased by a factor of 10 from the crystallized to the fully amorphized material. Correlatively, the amorphous fraction also modified the delay to reach the saturation conditions associated to the thermodynamic equilibria involved. On the other hand, it exhibited no influence neither on other kinetic parameters, such as activation energy of the dissolution process or partial order related to the proton concentration, nor on the nature of the neo-formed phase formed at the saturation of the leachate and identified as Thorium Phosphate Hydrogeno-Phosphate Hydrate (TPHPH). Beta-TUPD samples were also irradiated by gamma and alpha rays during leaching tests to study the effects of radiolysis in the leaching medium on the normalized leaching rate. It appeared that the radiolytic species occurring in the dissolution mechanism were unstable, disappearing quickly when stopping the irradiation. (author)

TPD IR studies of CO desorption from zeolites CuY and CuX

Science.gov (United States)

Datka, Jerzy; Kozyra, Paweł

2005-06-01

The desorption of CO from zeolites CuY and CuX was followed by TPD-IR method. This is a combination of temperature programmed desorption and IR spectroscopy. In this method, the status of activated zeolite (before adsorption), the process of adsorption, and the status of adsorbed molecules can be followed by IR spectroscopy, and the process of desorption (with linear temperature increase) can be followed both by IR spectroscopy and by mass spectrometry. IR spectra have shown two kinds of Cu + sites in both CuY and CuX. Low frequency (l.f.) band (2140 cm -1 in CuY and 2130 cm -1 in CuX) of adsorbed CO represents Cu + sites for which π back donation is stronger and σ donation is weaker whereas high frequency h.f. band (2160 cm -1 in CuY and 2155 cm -1 in CuX) represent Cu + sites for which π back donation is weaker and σ donation is stronger. The TPD-IR experiments evidenced that the Cu + sites represented by l.f. band bond CO more weakly than those represented by h.f. one, indicating that σ donation has more important impact to the strength of Cu +-CO bonding. On the contrary, π back donation has bigger contribution to the activation of adsorbed molecules.

Science teachers’ individual and social learning related to IBSE in the frames of a large-scale, long-term, collaborative TPD project

DEFF Research Database (Denmark)

Nielsen, Birgitte Lund; Sillasen, Martin

of collaborative inquiries locally. A major theme in the first year has been Inquiry Based Science Education (IBSE) recommended as a focus to improve science education internationally. The research presented focuses on the participating teachers’ intertwined levels of individual and social learning. Data from...... repeated surveys and case studies reveal a positive attitude towards trying IBSE in the own classroom, however with the main part of the reflections focused on students’ hands-on experiences and fewer including students manipulating science ideas, like posing hypotheses. Teachers’ reflections indicate......It is acknowledged internationally that teachers’ Professional Development (TPD) is crucial for reforming science teaching. The Danish QUEST project (“Qualifying in-service Education of Science Teachers”) is designed using widely agreed criteria for effective TPD: content focus, active learning...

The n-butyl amine TPD measurement of Brönsted acidity for solid catalysts by simultaneous TG/DTG-DTA

Science.gov (United States)

Sasca, V.; Avram, Livia; Verdes, Orsina; Popa, A.

2010-06-01

The method for Brönsted acidity measurement based on TPD of alkyl amines desorption by gas-chromatography or thermogravimetry was adapted for simultaneous TG/DTG-DTA analysis. The acidity measurements were focused on the 12-tungstophosphoric acid (H 3PW 12O 40) and its salts, especially with Cesium since these posses the highest Brönsted acidity and they are among the most interesting catalysts. The n-butyl amine (NBA) desorption takes place in three steps for Cs xH 3- xPW 12O 40, x = 0-2, and four steps for the Cs 2.5H 0.5PW 12O 40. The steps of desorption correspond to the release of NBA molecules in stages, as NBA or butene molecules resulted from the Hofmann elimination reaction and NH 3 + H 2O formed by decomposition of ammonium salt. The quantities of desorption products, C 4H 8 and NH 3 + H 2O, corresponding to the stages with the maximum desorption rates at 400-420 °C, respectively 560-600 °C, are in the stoichiometric ratio with the Brönsted acidity.

Isoform 1 of TPD52 (PC-1) promotes neuroendocrine transdifferentiation in prostate cancer cells

KAUST Repository

Moritz, Tom

2016-02-05

The tumour protein D52 isoform 1 (PC-1), a member of the tumour protein D52 (TPD52) protein family, is androgen-regulated and prostate-specific expressed. Previous studies confirmed that PC-1 contributes to malignant progression in prostate cancer with an important role in castration-resistant stage. In the present work, we identified its impact in mechanisms leading to neuroendocrine (NE) transdifferentiation. We established for long-term PC-1 overexpression an inducible expression system derived from the prostate carcinoma cell line LNCaP. We observed that PC-1 overexpression itself initiates characteristics of neuroendocrine cells, but the effect was much more pronounced in the presence of the cytokine interleukin-6 (IL-6). Moreover, to our knowledge, this is the first report that treatment with IL-6 leads to a significant upregulation of PC-1 in LNCaP cells. Other TPD52 isoforms were not affected. Proceeding from this result, we conclude that PC-1 overexpression enhances the IL-6-mediated differentiation of LNCaP cells into a NE-like phenotype, noticeable by morphological changes and increased expression of typical NE markers, like chromogranin A, synaptophysin or beta-3 tubulin. Immunofluorescent staining of IL-6-treated PC-1-overexpressing LNCaP cells indicates a considerable PC-1 accumulation at the end of the long-branched neuron-like cell processes, which are typically formed by NE cells. Additionally, the experimentally initiated NE transdifferentiation correlates with the androgen receptor status, which was upregulated additively. In summary, our data provide evidence for an involvement of PC-1 in NE transdifferentiation, frequently associated with castration resistance, which is a major therapeutic challenge in the treatment of advanced prostate cancer.

Ammonia IRMS-TPD measurements on Brønsted acidity of proton-formed SAPO-34.

Science.gov (United States)

Suzuki, Katsuki; Nishio, Takuma; Katada, Naonobu; Sastre, German; Niwa, Miki

2011-02-28

By utilizing the advantages of a combined method of IRMS-TPD of ammonia and DFT calculations, the solid acidity of HSAPO-34 was studied. The number, strength and structure of the Brønsted OH were measured experimentally. The quantitative measurements and DFT calculations supported the identification of Brønsted OH to account for the generation model of the Brønsted OH primarily located in the edge of the Si domain (island). The acid strength of SAPO-34 was slightly weaker than that of chabazite, a zeolite with the same structure. Thus, some important insights were obtained to understand the acid site generation of SAPO-34.

Immobilization of tetravalent actinides in three phosphate based ceramics: britholites, TPD and monazites/brabantites

International Nuclear Information System (INIS)

Terra, O.; Audubert, F.; Dacheux, N.; Guy, C.; Podor, R.

2004-01-01

Three phosphate based ceramics were studied for the immobilization of tri- and tetravalent actinides: britholites Ca 9 Nd 1-x An x IV (PO 4 ) 5-x (SiO 4 ) 1+x F 2 , monazites/brabantites Ln 1-2x III Ca x An x IV PO 4 and Thorium Phosphate Diphosphate (TPD) Th 4-x An x IV (PO 4 ) 4 P 2 O 7 . For each material, the incorporation of Th, U(IV), or Ce(IV) in the structure was examined. This work was the early beginning of the incorporation of 239 Pu and/or 238 Pu in order to evaluate the effects of α -decay on these three crystallographic structures. The syntheses were carried out using dry chemistry methods, involving mechanical grinding then heating treatment (1100 deg C ≤ θ ≤ 1400 deg C). For britholites, we showed that the incorporation of thorium was complete for weight loading lower than 20 wt.% through the (Nd 3+ , PO 4 3- ) ↔ (Th 4+ , SiO 4 4- ) coupled substitution, leading to the preparation of solid solutions. Due to redox problems, the incorporation of uranium was limited to 5 to 8 wt.% and always led to a two-phase mixture of U-britholite and CaU 2 O 5+y . For solid solutions based on TPD and for brabantites, the syntheses dealing with the incorporation of Th and/or U(IV) were improved by dry chemistry method using three mechanical grinding-calcination cycles. For both solids, homogeneous and single phase samples of the corresponding solid solutions were obtained. Finally, dense pellets of britholites, monazites/brabantites and TAn IV PD solid solutions were prepared in order to study their chemical durability during leaching tests. (authors)

Optical parameters of ITO/TPD/Alq3/Al luminescent structures, containing arrays of CdSe/ZnS colloidal quantum dots

Science.gov (United States)

Mikhailov, I. I.; Tarasov, S. A.; Lamkin, I. A.; Tadtaev, P. O.; Kozlovich, L. I.; Solomonov, A. V.; Stepanov, E. M.

2016-08-01

The luminescent organic ITO/TPD/Alq3/Al structures and CdSe/ZnS quantum dots (QD) arrays were created. Electrical and optical properties of the samples were examined. The luminescence of the layers and QD arrays was shown in the range of wavelengths from 400 to 680 nm. Luminescent structures with phosphors corresponding to the emission standards with CRI>98 and with color temperature of 5500 K and 6504 K were created.

A TPD-MS study of glassy carbon surfaces oxidized by CO2 and O2

Directory of Open Access Journals (Sweden)

MILA D. LAUSEVIC

2002-11-01

Full Text Available The temperature-programmed desorption (TPD method combined with mass spectrometric (MS analysis has been applied to investigate the surface properties of carbon materials. The apparatus consisting of a temperature-programmed furnace and a quadrupole mass spectrometer was constructed in order to characterize the surface of differently treated glassy carbon samples. In this work, samples of glassy carbon exposed to air, CO2 and O2 were examined. The desorption of H2O, CO and CO2, as major products, indicated the presence of different oxide groups. The amount of these groups for all samples was calculated. It is concluded that oxidation affects the nature and the amount of the surface oxide groups and contributes to their increased stability.

Alloy formation and chemisorption at Zn/Pt(111) bimetallic surfaces using alkali ISS, XPD, and TPD.

Science.gov (United States)

Ho, Chih-Sung; Martono, Eddie; Banerjee, Santanu; Roszell, John; Vohs, John; Koel, Bruce E

2013-11-21

Alloy formation and chemisorption at bimetallic surfaces formed by vapor-depositing Zn on a Pt(111) single crystal were investigated primarily by using X-ray photoelectron diffraction (XPD), X-ray photoelectron spectroscopy (XPS), low-energy alkali ion scattering spectroscopy (ALISS), low electron energy diffraction (LEED), and temperature programmed desorption (TPD). A wide range of conditions were investigated to explore whether deposition and annealing of Zn films could produce well-defined, ordered alloy surfaces, similar to those encountered for Sn/Pt(111) surface alloys. These attempts were unsuccessful, although weak, diffuse (2 × 2) spots were observed under special conditions. The particular PtZn bimetallic alloy created by annealing one monolayer of Zn on Pt(111) at 600 K, which has a Zn composition in the surface layer of about 5 at. %, was investigated in detail by using XPD and ALISS. Only a diffuse (1 × 1) pattern was observed from this surface by LEED, suggesting that no long-range, ordered alloy structure was formed. Zn atoms were substitutionally incorporated into the Pt(111) crystal to form a near-surface alloy in which Zn atoms were found to reside primarily in the topmost and second layers. The alloyed Zn atoms in the topmost layer are coplanar with the Pt atoms in the surface layer, without any "buckling" of Zn, that is, displacement in the vertical direction. This result is expected because of the similar size of Pt and Zn, based on previous studies of bimetallic Pt alloys. Zn atoms desorb upon heating rather than diffusing deep into the bulk of the Pt crystal. Temperature programmed desorption (TPD) measurements show that both CO and NO have lower desorption energies on the PtZn alloy surface compared to that on the clean Pt(111) surface.

Study of the thorium phosphate-diphosphate (TPD) dissolution: kinetic aspect - thermodynamic aspect: analysis of the neo-formed phases; Etude de la dissolution du phosphate diphosphate de thorium: - aspect cinetique - aspect thermodynamique: analyse des phases neoformees

Energy Technology Data Exchange (ETDEWEB)

Thomas, A.Ch

2000-10-06

The aim of this work is to study the aqueous corrosion of the thorium phosphate-diphosphate (TPD), of the formula Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}, in the framework of the actinides immobilization. In order to complete the anterior studies concerning solid solutions where thorium is substituted by a tetravalent ion (uranium (IV) or plutonium (IV)) in the TPD structure, compounds of thorium and neptunium phosphate-diphosphate, of formula Th{sub 4-x}Np{sub x}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}, have been prepared. Furthermore, a new chemical way of synthesis has been investigated in order to sinter solids solution of thorium and uranium phosphate-diphosphate (TUPD) in good conditions. The TPD dissolution study showed two principals steps. The first one corresponds to the control of element concentration by the material dissolution whereas the second corresponds to the formation of secondary precipitates for which thermodynamic equilibrium controls the concentration of the species in solution. Leaching tests have been performed varying several independent parameters in order to determine the TPD dissolution rate. The partial orders related to the protons or to the hydroxide ions have been found between 0.35 and 0.45 whereas the apparent dissolution rate constants are in the range 1.10{sup -5} for 9.10{sup -5} g.m{sup -2}.j{sup -1} for acidic and basic media. The neo-formed phases have been characterized after the dissolution of TPD and TUPD. We found that the TPD leaching in acidic medium leads to the formation of the crystallized thorium phosphate-hydrogen-phosphate (TPHP), of formula Th{sub 2}(PO{sub 4}){sub 2}(HPO{sub 4}), x H{sub 2}O, whereas the TUPD dissolution leads to the TPHP and an other compound, of formula (UO{sub 2}){sub 3}(PO{sub 4}){sub 2}, 5 H{sub 2}O. We calculated its solubility product which is in good agreement with those found in the literature. The phases formed during the leaching of solids containing plutonium; americium or curium (Th

Self irradiation effects on the thorium phosphate diphosphate dissolution (TPD): simulation by external irradiations

International Nuclear Information System (INIS)

Tamain, C.; Ozgumus, A.; Dacheux, N.; Garrido, F.; Thome, L.; Corbel, C.; Genet, M.

2004-01-01

The Thorium Phosphate Diphosphate (TPD), proposed as a ceramic for the long term immobilization of actinides, was externally irradiated with several ions and energies (but also with gamma rays) in order to simulate the self-irradiation. The influence of the electronic energy loss was first investigated. Thus, the XRD measurements have shown a complete amorphization of the material under 10 13 ions of Kr.cm -2 , while no significant structural change occurred after 5.10 13 S.cm -2 , 2.10 16 He.cm -2 or 320 kGy of dose of gamma rays. The dissolution of the raw and irradiated pellets was studied versus several parameters such as amorphized fraction, energy loss of incident ions, radiolytic species produced in situ in the leachate during irradiation (such as H 2 O 2 ), temperature and acidity. The results reveal an important increase of the dissolution kinetics for amorphized pellets compared to raw ceramic. (authors)

Study of Thorium Phosphate Diphosphate (TPD) formation in nitric medium for the decontamination of high activity actinides bearing effluents

International Nuclear Information System (INIS)

Rousselle, Jerome

2004-01-01

Considering several activities in the nuclear industry and research, several low-level liquids wastes (LLLW) containing actinides in nitric medium must be decontaminated before being released in the environment. These liquid wastes mainly contain significant amounts of uranium(VI), neptunium(V) and plutonium(IV). In this work, two chemical ways were studied to decontaminate LLLW then to incorporate simultaneously uranium, neptunium and plutonium in the Thorium Phosphate Diphosphate (TPD). Both ways started from a nitric solution containing thorium and the actinides considered, present at their lower stable oxidation state. The first way consisted in the initial precipitation of actinide and thorium mixed oxalate. After drying the mixture containing the powder and phosphoric acid under dried argon, a poly-phase system was obtained. It was mainly composed by a thorium-actinide oxalate-phosphate. This mixture was transformed into a TPDAn solid solution (An = U, Np and/or Pu) by heating treatment at 1200 deg. C under inert atmosphere. The second way consisted in the precipitation of a precursor of TPD, identified as the Thorium Phosphate Hydrogen Phosphate loaded with the actinides considered. The gel initially formed by mixing concentrated phosphoric acid solution with the nitric actinide solution was heated at 90 - 160 deg. C in a closed PTFE container for several weeks. It led to the TPDAn solid solutions after heating at 1100 deg. C in air or under inert argon. The efficiency of both processes was evaluated through the determination of the decontamination for each actinide considered. Considering the encouraging results obtained for both kinds of processes, some complementary studies are now required before performing the effective decontamination of real Low-Level Liquid Waste using one of the methods proposed. (author) [fr

A numerical study on the charge transport in TPD/Alq3-based organic light emitting diodes.

Science.gov (United States)

Kim, K S; Hwang, Y W; Lee, H G; Won, T Y

2014-08-01

We report our simulation study on the charge transport characteristic of the multi-layer structure for organic light emitting diodes (OLEDs). We performed a numerical simulation on a multilayer structure comprising a hole transport layer (HTL), an emission layer (EML), and an electron transport layer (ETL) between both electrodes. The material of the HTL is TPD (N,N'-Bis (3-methylphenyl)-N,N'-bis(phenyl) benzidine), and the ETL includes Alq3 (Tris (8-hyroxyquinolinato) aluminium). Here, we investigated the parameters such as recombination rates which influence the efficiency of the charge transport between layers in bilayer OLEDs. We also analyzed a transient response during the turn on/off period and the carrier transport in accordance with the variation of the injection barrier and applied voltage. In addition, our numerical simulation revealed that the insertion of the EML affects the photonic characteristics in bilayer structure and also the efficiency due to the difference in the internal barrier height.

The characteristics of electroplex generated from the organic light emitting diodes.

Science.gov (United States)

Shin, Dong-Myung

2010-10-01

The color stability and purity from OLED is of current interest. Aggregation of dyes alters the device color after fabrication of the devices. The aggregates can be exciplex and electroplex, which is the excited complex that generated after electrically excited state under high electric field. Comparative study of emission spectra of exciplex and electroplex leads us to conclude that the new electroplex states causes the bathochromic shift of the electroluminescence spectrum from the devices with TPD/PBD layers. The photoluminescence maximum obtained from the TPD/PBD layers of the device was 420 nm, and the electroluminescence maximum obtained from the device became 480 nm. The bathochromic shift cannot be attained with photoluminescence study with highly concentrated TPD/PBD mixture. This clearly indicates that the 480 nm spectrum of the devices is not resulted from the exciplex formation with TPD and PBD. We observed the overshoot in EL spectrum from the OLEDs. The most intense overshoot was observed at 460 nm, which is due to the aggregate that are formed after the electric field has been removed from the devices.

Implementação da Técnica de Dessorção Térmica Programada (TPD) usando Espectrometria de Massa Quadrupolo

OpenAIRE

Barreto, Ana Marta Fortunato

2011-01-01

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do Grau de Mestre em Engenharia Física O projecto “Implementação da Técnica de Dessorção Térmica Programada (TPD) usando Espectrometria de Massa Quadrupolo”, apresentado nesta Dissertação de Mestrado em Engenharia Física, surgiu como uma proposta de requalificação ao aparelho de análise de superfícies Multitécnica. A dessorção térmica é o fenómeno que permite a separação física de ...

Ammonia IRMS-TPD measurements and DFT calculation on acidic hydroxyl groups in CHA-type zeolites.

Science.gov (United States)

Suzuki, Katsuki; Sastre, German; Katada, Naonobu; Niwa, Miki

2007-12-07

Brønsted acidity of H-chabazite (CHA) zeolites (Si : Al(2) = 4.2) was investigated by means of ammonia infrared-mass spectrometry/temperature-programmed desorption (IRMS-TPD) methods and density functional calculations. Four IR bands were observed at 3644, 3616, 3575 and 3538 cm(-1), and they were ascribable to the acidic OH groups on four nonequivalent oxygen sites in the CHA structure. The absorption band at 3538 cm(-1) was attributed to the O(4)H in the 6-membered ring (MR), and ammonia adsorption energy (DeltaU) of this OH group was the lowest among the 4 kinds of OH groups. The other 3 bands were assigned to the acidic OH groups in 8MR. It was observed that the DeltaU in 8 and 6MR were 131 (+/-3) and 101 kJ mol(-1), respectively. On the other hand, the density functional theory (DFT) calculations within periodic boundary conditions yielded the adsorption energies on these OH groups in 8 and 6MR to be ca. 130 and 110 kJ mol(-1), respectively, in good agreement with the experimentally-observed values.

Study of the irradiation effects on thorium phosphate diphosphate ({beta}-TPD): consequences on its chemical durability; Etude des effets d'irradiation sur le phosphate diphosphate de thorium ({beta}-PDT): consequences sur la durabilite chimique

Energy Technology Data Exchange (ETDEWEB)

Tamain, C

2005-12-15

Since Thorium Phosphate Diphosphate (beta-TPD) can be considered as a potential host matrix for long-term storage in underground repository, it is necessary to study the irradiation effects on the structure of this ceramics and the consequences on its chemical durability. Sintered samples of beta-TPD and of associated solid solutions of beta-TUPD were irradiated under ion beams and then altered in aqueous solutions. Depending on the electronic LET value, beta-TPD can be completely or partly amorphized. Furthermore, the ability of recrystallization of the amorphous material by thermal annealing was also demonstrated. Some leaching tests, realized on these irradiated samples, have shown a significant effect of the amorphous fraction on the normalized dissolution rate which was increased by a factor of 10 from the crystallized to the fully amorphized material. Correlatively, the amorphous fraction also modified the delay to reach the saturation conditions associated to the thermodynamic equilibria involved. On the other hand, it exhibited no influence neither on other kinetic parameters, such as activation energy of the dissolution process or partial order related to the proton concentration, nor on the nature of the neo-formed phase formed at the saturation of the leachate and identified as Thorium Phosphate Hydrogeno-Phosphate Hydrate (TPHPH). Beta-TUPD samples were also irradiated by gamma and alpha rays during leaching tests to study the effects of radiolysis in the leaching medium on the normalized leaching rate. It appeared that the radiolytic species occurring in the dissolution mechanism were unstable, disappearing quickly when stopping the irradiation. (author)

Recovery of Boron and Separation of Lithium from Uyuni Salar Brine using 2, 2, 4-Trimethyl -1, 3-Pentanediol (TPD)

International Nuclear Information System (INIS)

Kumar, Jyothi Rajesh; Kim, Chul-Joo; Yoon, Ho-Sung; Lee, Jin-Young; Kang, Dong-Jun

2015-01-01

In the present study, extraction and separation possibilities have been established for boron and lithium from Uyuni salar brine. Diols were shown to be effective extraction reagents for boron. The present scientific study was developed with 2, 2, 4-trimethyl-1, 3-pentanediol (TPD) as an extractant system. For fixing the diluent system, various diluents were tested and it was found that chloroform is a better diluent for boron extraction. Further, experimental studies on the extraction equilibrium time, pH influence, and phase ratio effects on boron extraction were conducted and the conditions for boron recovery and lithium separation were optimized. The McCabe Thiele diagram was established to optimize the number of extraction stages for boron extraction. Finally, stripping studies of boron from the loaded organic phase using various salts were performed.

Evaluation of the characteristics of boron-dose enhancer (BDE) materials for BNCT using near threshold {sup 7}Li(p,n){sup 7}Be direct neutrons

Energy Technology Data Exchange (ETDEWEB)

Bengua, Gerard [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennann-gun, Osaka 590-0494 (Japan); Kobayashi, Tooru [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennann-gun, Osaka 590-0494 (Japan); Tanaka, Kenichi [Research Institute for Radiation Biology and Medicine, Hiroshima University, Kasumi, Minami-ku, Hiroshima 734-8553 (Japan); Nakagawa, Yoshinobu [National Kagawa Children' s Hospital, Zentsuji-cho, Zentsuji, Kagawa 765-8501 (Japan)

2004-03-07

The characteristics of a number of candidate boron-dose enhancer (BDE) materials for boron neutron capture therapy (BNCT) using near threshold {sup 7}Li(p,n){sup 7}Be direct neutrons were evaluated based on the treatable protocol depth (TPD), defined in this paper. Simulation calculations were carried out by means of MCNP-4B transport code for candidate BDE materials, namely, (C{sub 2}H{sub 4}){sub n}, (C{sub 2}H{sub 3}F){sub n}, (C{sub 2}H{sub 2}F{sub 2}){sub n}, (C{sub 2}HF{sub 3}){sub n}, (C{sub 2}D{sub 4}){sub n}, (C{sub 2}F{sub 4}){sub n}, beryllium metal, graphite, D{sub 2}O and {sup 7}LiF. Dose protocols applied were those used for intra-operative BNCT treatment for brain tumour currently used in Japan. The maximum TPD (TPD{sub max}) for each BDE material was found to be between 4 cm and 5 cm in the order of (C{sub 2}H{sub 4}){sub n} < (C{sub 2}H{sub 3}F){sub n} < (C{sub 2}H{sub 2}F{sub 2}){sub n} < (C{sub 2}HF{sub 3}){sub n} < beryllium metal < (C{sub 2}D{sub 4}){sub n} < graphite < (C{sub 2}F{sub 4}){sub n} < D{sub 2}O < {sup 7}LiF. Based on the small and arbitrary variations in the TPD{sub max} for these materials, an explicit advantage of a candidate BDE material could not be established from the TPD{sub max} alone. The dependence of TPD on BDE thickness was found to be influenced by the type of BDE material. For materials with hydrogen, sharp variations in TPD were observed, while those without hydrogen exhibited more moderate fluctuations in TPD as the BDE thickness was varied. The BDE thickness corresponding to TPD{sub max} (BDE(TPD{sub max})) was also found to depend on the type of BDE material used. Thicker BDE(TPD{sub max}), obtained mostly for BDE materials without hydrogen, significantly reduced the dose rates within the phantom. The TPD{sub max}, the dependence of TPD on BDE thickness and the BDE (TPD{sub max}) were ascertained as appropriate optimization criteria in choosing suitable BDE materials for BNCT. Among the candidate BDE materials

Novel Base Station MIMO Antennas with Enhanced Spectral Efficiencies Using Angular Reuse

Directory of Open Access Journals (Sweden)

Miguel Mora-Andreu

2015-01-01

Full Text Available The true polarization diversity (TPD technique is combined with the spatial diversity technique in novel MIMO antenna array geometries with a large number of elements. The use of a large number of elements requires some angular reuse within the array for polarization diversity. With designs compatible with existing base station antenna array configurations, the novel geometries with combining diversity schemes are shown to be able to achieve near the maximum spectral efficiencies. True polarization diversity (TPD schemes are found to be an excellent complement to more conventional spatial diversity schemes for obtaining optimum MIMO array performance in base station antennas.

Deactivation of Pd particles supported on Nb 2O 5/Cu 3Au(1 0 0): SFG and TPD studies from UHV to 100 mbar

Science.gov (United States)

Höbel, Frank; Bandara, Athula; Rupprechter, Günther; Freund, Hans-Joachim

2006-02-01

Structural changes that occur on Pd-Nb 2O 5/Cu 3Au(1 0 0) model catalysts upon thermal annealing were followed by sum frequency generation (SFG) and temperature-programmed desorption (TPD) using CO as probe molecule. SFG experiments were performed both under ultrahigh vacuum and mbar pressure. Heating the catalyst to temperatures above 300 K lead to an irreversible 50% decrease in the CO adsorption capacity and modified the remaining adsorption sites. Alterations of the phase between resonant and non-resonant SFG signals upon annealing indicate a change in the electronic structure of the surface, which excludes Pd sintering or migration of Nb 2O 5 over Pd particles to cause the observed effect and rather suggests the formation of "mixed Pd-NbO x" sites. The same changes in surface properties also occur during CO hydrogenation at 1 bar and high temperature, pointing to an involvement of "mixed Pd-NbO x" sites in catalytic reactions.

[Multiple emissions in organic electroluminescent device using a mixed layer as an emitter].

Science.gov (United States)

Zhu, Wen-qing; Wu, You-zhi; Zheng, Xin-you; Jiang, Xue-yin; Zhang, Zhi-lin; Sun, Run-guang; Xu, Shao-hong

2005-04-01

A organic electroluminescent device has been fabricated by using a mixed layer as an emitter. The configuration of the device is ITO/TPD/TPD: PBD(equimole)/PBD/A1, in which TPD (N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine) and PBD (2-(4'-biphenyl)-5-(4''-tert-butylphenyl)-1,3,4-oxadiazole) are used as hole transport material and electron transport material, respectively. Broad and red-shifted electroluminescent spectra related to the fluorescence of constituent materials were observed. It is suggested that the monomer, exciplex and electroplex emissions are simultaneously involved in EL spectra by comparison of the EL with the PL spectra and decomposition of the EL spectrum. The type of exciplex is the interaction between the excited state TPD (TPD*) and PBD in the ground state, and the type of electroplex is a (D+-A-)* complex by cross-recombination of hole on the charged hole transport molecule (D+) and electron on the charged electron transport molecule (A-). All types of excited states show different formation mechanisms and recombination processes under electric field. The change of emission strengths from monomer and excited complexes lead to a blue-shift of the emissive spectra with an increasing electric field. The maximum luminance and external quantum efficiency of this device are 240 cd x (cm2)(-1) and 0.49%, respectively. The emissions from exciplex or electroplex formation at the organic solid interface generally present a broad and red-shifted emissive band, providing an effective method for tuning of emission color in organic electroluminescent devices.

Incorporation of tetravalent actinides in three phosphated matrices: britholite, monazite/brabandite and thorium phosphate diphosphate (β-TPD)

International Nuclear Information System (INIS)

Terra, O.

2005-03-01

Three phosphate based ceramics were studied for the immobilization of tri- and tetravalent actinides: britholite Ca 9 Nd 1-x An x IV (PO 4 ) 5-x (SiO 4 ) 1+x F 2 , monazite/brabantite solid solutions Ln 1-2x III Ca x An x IP O 4 and Thorium Phosphate Diphosphate (β-TPD) Th 4- xAn x IV (PO 4 ) 4 P 2 O 7 . For each material, the incorporation of thorium and uranium (IV) was studied as a surrogate of plutonium. This work was the early beginning of the incorporation of 239 Pu and/or 238 Pu in order to evaluate the effects of α-decay on the three crystallographic structures. The incorporation of tetravalent cations was carried out by dry chemistry methods, using mechanical grinding to improve the reactivity of the initial mixture then the homogeneity of final solid prepared after calcination at high temperature (1200-1400 deg C). For britholites, the thorium incorporation was complete for weight loading up to 20 wt.%, leading to the preparation of homogeneous and single phase solid solutions when using the coupled substitution (Nd 3+ , PO 4 3- ) ↔ (Th 4+ , SiO 4 4- ). Due to redox problems, the incorporation of uranium was limited to 5 to 8 wt.% and always led to a two-phase mixture of U-britholite and CaU 2 O 5+y . The preparation of homogeneous solid solutions of β-TUPD and of brabantites containing thorium and uranium samples was successfully obtained using three steps of mechanical grinding/calcination. For each matrix, dense pellets were prepared prior to the study of their chemical behaviour during leaching tests. The chemical durability of brabantites and β-TUPD were found to be close to that reported in literature. The formation of neo-formed phases was also evidenced onto the surface of Th-britholite samples. (author)

Approximate maximum parsimony and ancestral maximum likelihood.

Science.gov (United States)

Alon, Noga; Chor, Benny; Pardi, Fabio; Rapoport, Anat

2010-01-01

We explore the maximum parsimony (MP) and ancestral maximum likelihood (AML) criteria in phylogenetic tree reconstruction. Both problems are NP-hard, so we seek approximate solutions. We formulate the two problems as Steiner tree problems under appropriate distances. The gist of our approach is the succinct characterization of Steiner trees for a small number of leaves for the two distances. This enables the use of known Steiner tree approximation algorithms. The approach leads to a 16/9 approximation ratio for AML and asymptotically to a 1.55 approximation ratio for MP.

Maximum permissible dose

International Nuclear Information System (INIS)

Anon.

1979-01-01

This chapter presents a historic overview of the establishment of radiation guidelines by various national and international agencies. The use of maximum permissible dose and maximum permissible body burden limits to derive working standards is discussed

Stabilization of N,N′-bis(3-methylphenyl)-N,N′-bis(phenyl)benzidine thin film morphology with UV light

Energy Technology Data Exchange (ETDEWEB)

Tomović, A.Ž.; Markešević, N. [Institute of Physics, University of Belgrade, Pregrevica 118, 11000 Belgrade (Serbia); Scarpellini, M.; Bovio, S. [Interdisciplinary Centre for Nanostructured Materials and Interfaces (CIMAINA), Università di Milano, Via Celoria 16, 20133 Milan (Italy); Lucenti, E. [Interdisciplinary Centre for Nanostructured Materials and Interfaces (CIMAINA), Università di Milano, Via Celoria 16, 20133 Milan (Italy); Institute of Molecular Science and Technology of CNR, via Golgi 19, 20133 Milan (Italy); Milani, P. [Interdisciplinary Centre for Nanostructured Materials and Interfaces (CIMAINA), Università di Milano, Via Celoria 16, 20133 Milan (Italy); Zikic, R. [Institute of Physics, University of Belgrade, Pregrevica 118, 11000 Belgrade (Serbia); Jovanović, V.P., E-mail: vladimir.jovanovic@ipb.ac.rs [Institute of Physics, University of Belgrade, Pregrevica 118, 11000 Belgrade (Serbia); Srdanov, V.I. [Interdisciplinary Centre for Nanostructured Materials and Interfaces (CIMAINA), Università di Milano, Via Celoria 16, 20133 Milan (Italy)

2014-07-01

Owing to their low glass transition temperature, T{sub g}, amorphous thin films of N,N′-bis(3-methylphenyl)-N,N′-bis(phenyl)benzidine (TPD) undergo morphological changes even at room temperature. It has been noticed previously that exposure to UV light can increase apparent T{sub g} of TPD films and thus stabilize their morphology. However, the reason behind increase in structural stability was not examined at the time. Here we present evidence that TPD molecules undergo photo-oxidation in air when exposed to λ ≈ 350 nm radiation and that less than 5% of the photo-oxidized species are needed to prevent dewetting of thin TPD films. We propose that photo-oxidized TPD species bind strongly to both ordinary TPD molecules and to terminal hydroxyl groups at the substrate surface, which decreases mobility of TPD molecules and makes thin TPD film less prone to morphology changes. - Highlights: • We made variable thickness TPD films and exposed them to UV light under ambient conditions. • Mass spectroscopy and proton NMR measurements of irradiated and pristine TPD films • TPD molecules undergo oxidation process under UV light irradiation. • Dipole–dipole interactions may be responsible for stabilization of morphological changes.

Cosmic shear measurement with maximum likelihood and maximum a posteriori inference

Science.gov (United States)

Hall, Alex; Taylor, Andy

2017-06-01

We investigate the problem of noise bias in maximum likelihood and maximum a posteriori estimators for cosmic shear. We derive the leading and next-to-leading order biases and compute them in the context of galaxy ellipticity measurements, extending previous work on maximum likelihood inference for weak lensing. We show that a large part of the bias on these point estimators can be removed using information already contained in the likelihood when a galaxy model is specified, without the need for external calibration. We test these bias-corrected estimators on simulated galaxy images similar to those expected from planned space-based weak lensing surveys, with promising results. We find that the introduction of an intrinsic shape prior can help with mitigation of noise bias, such that the maximum a posteriori estimate can be made less biased than the maximum likelihood estimate. Second-order terms offer a check on the convergence of the estimators, but are largely subdominant. We show how biases propagate to shear estimates, demonstrating in our simple set-up that shear biases can be reduced by orders of magnitude and potentially to within the requirements of planned space-based surveys at mild signal-to-noise ratio. We find that second-order terms can exhibit significant cancellations at low signal-to-noise ratio when Gaussian noise is assumed, which has implications for inferring the performance of shear-measurement algorithms from simplified simulations. We discuss the viability of our point estimators as tools for lensing inference, arguing that they allow for the robust measurement of ellipticity and shear.

Catalyst and Fuel Interactions to Optimize Endothermic Cooling

Science.gov (United States)

2016-08-30

0.008 0.010 CO TPD alumina film 1st CO TPD - boron doped /Pt7/alumina 2nd CO TPD - boron doped /Pt7/alumina 2nd CO TPD Pt7/alumina CO TPD - 700 K B2H6...different support materials. We also studied the effects of boron doping and alumina atomic layer deposition overcoating of the clusters, on activity...theory support. The second task was to develop efficient milling-based processes for high rate/low cost preparation of energetic nanoparticles of

Influence of heterojunction interface on exciplex emission from organic light-emitting diodes under electric fields

Energy Technology Data Exchange (ETDEWEB)

Yang, Shengyi; Zhang, Xiulong; Lou, Zhidong; Hou, Yanbing [Beijing Jiaotong University, Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing (China)

2008-03-15

In this paper, electroluminescence from organic light-emitting diodes based on 2-(4'-biphenyl)-5-(4{sup ''}-tert-butylphenyl)-1,3,4-oxadiazole (PBD) and N,N'-diphenyl-N,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD) is reported. Based on the exciplex emission from the TPD/PBD interface under high electric fields, the influence of the TPD/PBD interface on exciplex emission was investigated by increasing the number of TPD/PBD interfaces while keeping both the total thickness of the TPD layer and the PBD layer constant in the multiple quantum-wells (MQW) device ITO/TPD/[PBD/TPD]{sub n}/PBD/Al (n is the well number that was varied from 0 to 3). Our experimental data shows that exciplex emission can be enhanced by suitably increasing the well number of this kind of MQW-like device. (orig.)

Structure–acidity correlation of supported tungsten(VI)-oxo-species: FT-IR and TPD studies of adsorbed pyridine and catalytic decomposition of 2-propanol

Energy Technology Data Exchange (ETDEWEB)

Zaki, M.I., E-mail: mizaki@mu.edu.eg; Mekhemer, G.A.H.; Fouad, N.E.; Rabee, A.I.M.

2014-07-01

The amount of 10 wt%-WO{sub 3} was supported on alumina, titania or silica by impregnation with aqueous solution of ammonium paratungstate and subsequent calcination at 500 °C for 10 h. Tungstate-related chemical and physical changes in the calcination products were resolved by ex-situ infrared (IR) spectroscopy. Nature of exposed surface acid sites were probed by in-situ IR spectroscopy of adsorbed pyridine (Py) molecules at room temperature (RT). The relative strength of the acid sites thus probed was gauged by combining results of temperature-programmed desorption (TPD) measurements of the RT-adsorbed Py with those communicated by in-situ IR spectra of residual Py on the surface after a brief thermoevacuation at high temperatures (100–300 °C). Reactivity of the surface acid sites was tested toward 2-propanal catalytic decomposition, and observed by in-situ IR gas phase spectra. Results obtained were correlated with predominant structures assumed by the supported tungstate species. Accordingly, polymerization of the supported tungstate into 2-/3-dimensional structures, was found to be relatively most advanced on favorable locations of titania surfaces as compared to the case on alumina or silica surfaces. Consequently, the Lewis acidity was strengthened, and strong Bronsted acidity was evolved, leading to a 2-propanol dehydration catalyst (tungstate/titania) of optimal activity and selectivity. Strong tungstate/support interfacial interactions were found to hamper the formation of the strongly acidic and catalytically active polymeric structures of the supported tungstate (i.e., the case on alumina or silica).

Structure–acidity correlation of supported tungsten(VI)-oxo-species: FT-IR and TPD studies of adsorbed pyridine and catalytic decomposition of 2-propanol

International Nuclear Information System (INIS)

Zaki, M.I.; Mekhemer, G.A.H.; Fouad, N.E.; Rabee, A.I.M.

2014-01-01

The amount of 10 wt%-WO 3 was supported on alumina, titania or silica by impregnation with aqueous solution of ammonium paratungstate and subsequent calcination at 500 °C for 10 h. Tungstate-related chemical and physical changes in the calcination products were resolved by ex-situ infrared (IR) spectroscopy. Nature of exposed surface acid sites were probed by in-situ IR spectroscopy of adsorbed pyridine (Py) molecules at room temperature (RT). The relative strength of the acid sites thus probed was gauged by combining results of temperature-programmed desorption (TPD) measurements of the RT-adsorbed Py with those communicated by in-situ IR spectra of residual Py on the surface after a brief thermoevacuation at high temperatures (100–300 °C). Reactivity of the surface acid sites was tested toward 2-propanal catalytic decomposition, and observed by in-situ IR gas phase spectra. Results obtained were correlated with predominant structures assumed by the supported tungstate species. Accordingly, polymerization of the supported tungstate into 2-/3-dimensional structures, was found to be relatively most advanced on favorable locations of titania surfaces as compared to the case on alumina or silica surfaces. Consequently, the Lewis acidity was strengthened, and strong Bronsted acidity was evolved, leading to a 2-propanol dehydration catalyst (tungstate/titania) of optimal activity and selectivity. Strong tungstate/support interfacial interactions were found to hamper the formation of the strongly acidic and catalytically active polymeric structures of the supported tungstate (i.e., the case on alumina or silica).

Maximum Acceleration Recording Circuit

Science.gov (United States)

Bozeman, Richard J., Jr.

1995-01-01

Coarsely digitized maximum levels recorded in blown fuses. Circuit feeds power to accelerometer and makes nonvolatile record of maximum level to which output of accelerometer rises during measurement interval. In comparison with inertia-type single-preset-trip-point mechanical maximum-acceleration-recording devices, circuit weighs less, occupies less space, and records accelerations within narrower bands of uncertainty. In comparison with prior electronic data-acquisition systems designed for same purpose, circuit simpler, less bulky, consumes less power, costs and analysis of data recorded in magnetic or electronic memory devices. Circuit used, for example, to record accelerations to which commodities subjected during transportation on trucks.

Neutron spectra unfolding with maximum entropy and maximum likelihood

International Nuclear Information System (INIS)

Itoh, Shikoh; Tsunoda, Toshiharu

1989-01-01

A new unfolding theory has been established on the basis of the maximum entropy principle and the maximum likelihood method. This theory correctly embodies the Poisson statistics of neutron detection, and always brings a positive solution over the whole energy range. Moreover, the theory unifies both problems of overdetermined and of underdetermined. For the latter, the ambiguity in assigning a prior probability, i.e. the initial guess in the Bayesian sense, has become extinct by virtue of the principle. An approximate expression of the covariance matrix for the resultant spectra is also presented. An efficient algorithm to solve the nonlinear system, which appears in the present study, has been established. Results of computer simulation showed the effectiveness of the present theory. (author)

Maximum Power from a Solar Panel

Directory of Open Access Journals (Sweden)

Michael Miller

2010-01-01

Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone

Directory of Open Access Journals (Sweden)

Oleg Kikhtyanin

2018-05-01

Full Text Available MgGa layered double hydroxides (Mg/Ga = 2–4 were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH3-TPD, CO2-TPD, SEM, and DRIFT and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO2-TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO2-TPD curve was attributed to the decomposition of carbonates newly formed by CO2 interaction with interlayer carbonates rather than to CO2 desorption from basic sites. Accordingly, CO2-TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had

Physico-Chemical Properties of MgGa Mixed Oxides and Reconstructed Layered Double Hydroxides and Their Performance in Aldol Condensation of Furfural and Acetone.

Science.gov (United States)

Kikhtyanin, Oleg; Čapek, Libor; Tišler, Zdeněk; Velvarská, Romana; Panasewicz, Adriana; Diblíková, Petra; Kubička, David

2018-01-01

MgGa layered double hydroxides (Mg/Ga = 2-4) were synthesized and used for the preparation of MgGa mixed oxides and reconstructed hydrotalcites. The properties of the prepared materials were examined by physico-chemical methods (XRD, TGA, NH 3 -TPD, CO 2 -TPD, SEM, and DRIFT) and tested in aldol condensation of furfural and acetone. The as-prepared phase-pure MgGa samples possessed hydrotalcite structure, and their calcination resulted in mixed oxides with MgO structure with a small admixture phase characterized by a reflection at 2θ ≈ 36.0°. The interaction of MgGa mixed oxides with pure water resulted in reconstruction of the HTC structure already after 15 s of the rehydration with maximum crystallinity achieved after 60 s. TGA-MS experiments proved a substantial decrease in carbonates in all rehydrated samples compared with their as-prepared counterparts. This allowed suggesting presence of interlayer hydroxyls in the samples. Acido-basic properties of MgGa mixed oxides determined by TPD technique did not correlate with Mg/Ga ratio which was explained by the specific distribution of Ga atoms on the external surface of the samples. CO 2 -TPD method was also used to evaluate the basic properties of the reconstructed MgGa samples. In these experiments, an intensive peak at T = 450°C on CO 2 -TPD curve was attributed to the decomposition of carbonates newly formed by CO 2 interaction with interlayer carbonates rather than to CO 2 desorption from basic sites. Accordingly, CO 2 -TPD method quantitatively characterized the interlayer hydroxyls only indirectly. Furfural conversion on reconstructed MgGa materials was much larger compared with MgGa mixed oxides confirming that Brønsted basic sites in MgGa catalysts, like MgAl catalysts, were active in the reaction. Mg/Ga ratio in mixed oxides influenced product selectivity which was explained by the difference in textural properties of the samples. In contrast, Mg/Ga ratio in reconstructed catalysts had practically

IR and TPD studies of the interaction of alkenes with Cu + sites in CuNaY and CuNaX zeolites of various Cu content. The heterogeneity of Cu + sites

Science.gov (United States)

Datka, J.; Kukulska-Zajaç, E.; Kozyra, P.

2006-08-01

Cu + ions in zeolites activate organic molecules containing π electrons by π back donation, which results in a distinct weakening of multiple bonds. In this study, we followed the activation of alkenes (ethene and propene) by Cu + ions in CuY and CuX zeolites of various Cu content. We also studied the strength of bonding of alkenes to Cu + ions. IR studies have shown that there are two kinds of Cu + sites of various electron donor properties. We suppose that they could be attributed to the presence of Cu + ions of various number of oxygen atoms surrounding the cation. IR studies have shown that Cu ions introduced into Y and X zeolites in the first-order (at low Cu content) form Cu + ions of stronger electron donor properties (i.e. activate alkenes to larger extend) than Cu ions introduced in the next order (at higher Cu content). IR and TPD studies of alkenes desorption evidenced that Cu + ions of stronger electron donor properties bond alkenes stronger than less electron donor ones. It suggests that π back donation has more important contribution to the strength of bonding alkenes to cation than π donation.

Maximum concentrations at work and maximum biologically tolerable concentration for working materials 1991

International Nuclear Information System (INIS)

1991-01-01

The meaning of the term 'maximum concentration at work' in regard of various pollutants is discussed. Specifically, a number of dusts and smokes are dealt with. The valuation criteria for maximum biologically tolerable concentrations for working materials are indicated. The working materials in question are corcinogeneous substances or substances liable to cause allergies or mutate the genome. (VT) [de

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Science.gov (United States)

2010-07-01

... cylinders having an internal diameter of 13.0 cm and a 15.5 cm stroke length, the rounded displacement would... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes...

Credal Networks under Maximum Entropy

OpenAIRE

Lukasiewicz, Thomas

2013-01-01

We apply the principle of maximum entropy to select a unique joint probability distribution from the set of all joint probability distributions specified by a credal network. In detail, we start by showing that the unique joint distribution of a Bayesian tree coincides with the maximum entropy model of its conditional distributions. This result, however, does not hold anymore for general Bayesian networks. We thus present a new kind of maximum entropy models, which are computed sequentially. ...

Maximum Entropy in Drug Discovery

Directory of Open Access Journals (Sweden)

Chih-Yuan Tseng

2014-07-01

Full Text Available Drug discovery applies multidisciplinary approaches either experimentally, computationally or both ways to identify lead compounds to treat various diseases. While conventional approaches have yielded many US Food and Drug Administration (FDA-approved drugs, researchers continue investigating and designing better approaches to increase the success rate in the discovery process. In this article, we provide an overview of the current strategies and point out where and how the method of maximum entropy has been introduced in this area. The maximum entropy principle has its root in thermodynamics, yet since Jaynes’ pioneering work in the 1950s, the maximum entropy principle has not only been used as a physics law, but also as a reasoning tool that allows us to process information in hand with the least bias. Its applicability in various disciplines has been abundantly demonstrated. We give several examples of applications of maximum entropy in different stages of drug discovery. Finally, we discuss a promising new direction in drug discovery that is likely to hinge on the ways of utilizing maximum entropy.

Maximum Quantum Entropy Method

OpenAIRE

Sim, Jae-Hoon; Han, Myung Joon

2018-01-01

Maximum entropy method for analytic continuation is extended by introducing quantum relative entropy. This new method is formulated in terms of matrix-valued functions and therefore invariant under arbitrary unitary transformation of input matrix. As a result, the continuation of off-diagonal elements becomes straightforward. Without introducing any further ambiguity, the Bayesian probabilistic interpretation is maintained just as in the conventional maximum entropy method. The applications o...

Weighted Maximum-Clique Transversal Sets of Graphs

OpenAIRE

Chuan-Min Lee

2011-01-01

A maximum-clique transversal set of a graph G is a subset of vertices intersecting all maximum cliques of G. The maximum-clique transversal set problem is to find a maximum-clique transversal set of G of minimum cardinality. Motivated by the placement of transmitters for cellular telephones, Chang, Kloks, and Lee introduced the concept of maximum-clique transversal sets on graphs in 2001. In this paper, we study the weighted version of the maximum-clique transversal set problem for split grap...

Charge carriers at organic heterojunction interface: Exciplex emission or electroplex emission?

Science.gov (United States)

Yang, Shengyi; Zhang, Xiulong; Hou, Yanbing; Deng, Zhenbo; Xu, Xurong

2007-05-01

We report the electroluminescence (EL) of organic heterojunction devices based on N ,N'-diphenyl-N ,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4',-diamine (TPD) and 2-(4'-biphenyl)-5-(4″-tert-butylphenyl)-1,3,4-oxadiazole (PBD). Besides monomolecular emissions from TPD, there are two additional EL peaks at around 460 and 480nm from the bilayer device indium tin oxide (ITO)/TPD(100nm )/PBD(45nm)/Al. Our experimental data confirmed that the EL emission maximized at around 460nm is from electroplex as the result of charge carriers cross recombination at the TPD/PBD interface and the EL emission maximized at around 480nm originates from (TPD*PBD)-type exciplex.

Maximum power demand cost

International Nuclear Information System (INIS)

Biondi, L.

1998-01-01

The charging for a service is a supplier's remuneration for the expenses incurred in providing it. There are currently two charges for electricity: consumption and maximum demand. While no problem arises about the former, the issue is more complicated for the latter and the analysis in this article tends to show that the annual charge for maximum demand arbitrarily discriminates among consumer groups, to the disadvantage of some [it

Influence of co-deposited active layers on carrier transport and luminescent properties in organic light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Murata, Masaya; Yamamoto, Takayuki; Haishi, Motoki; Ohtani, Naoki [Department of Electronics, Doshisha University, Tatara-Miyakodani, Kyotanabe-shi, Kyoto (Japan); Ando, Taro [Central Research Laboratory, Hamamatsu Photonics, Hirakuchi, Hamakita-ku, Hamamatsu-shi, Shizuoka (Japan)

2009-01-15

We have investigated the influence of a co-deposited active layer in organic light-emitting diodes (OLEDs) on carrier transport and optical properties to improve radiative characteristics of OLEDs. The co-deposited layer consists of two organic materials; one is a hole transport material (TPD) and the other is an electron transport/emissive material (Alq3). We evaluated current-voltage characteristics and electroluminescence (EL) properties of various samples in which the thicknesses and compound ratios of the co-deposited layers are different. The results indicate that the devices consisting of TPD:Alq3 co-deposited layer sandwiched between TPD and Alq3 layers exhibit lower starting voltages for the light emission than the sample of simple TPD/Alq3 heterojunction structure. In addition, the starting voltage is independent of the thickness of TPD:Alq3 co-deposited layer. These samples have two interfaces at both surfaces of TPD:Alq3 co-deposited layer. Thus, we estimated the radiative recombination occurs at the interfaces. Nevertheless, we found that the radiative recombination occurs only at the interface of TPD:Alq3 co-deposited layer and Alq3 layer. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Study on the Secant Segmentation Algorithm of Rubber Tree

Science.gov (United States)

Li, Shute; Zhang, Jie; Zhang, Jian; Sun, Liang; Liu, Yongna

2018-04-01

Natural rubber is one of the most important materials in the national defense and industry, and the tapping panel dryness (TPD) of the rubber tree is one of the most serious diseases that affect the production of rubber. Although considerable progress has been made in the more than 100 years of research on the TPD, there are still many areas to be improved. At present, the method of artificial observation is widely used to identify TPD, but the diversity of rubber tree secant symptoms leads to the inaccurate judgement of the level of TPD. In this paper, image processing technology is used to separate the secant and latex, so that we can get rid of the interference factors, get the exact secant and latex binary image. By calculating the area ratio of the corresponding binary images, the grade of TPD can be classified accurately. and can also provide an objective basis for the accurate identification of the tapping panel dryness (TPD) level.

Teacher Professional Development for Technology Integration in a Primary School Learning Community

Science.gov (United States)

Liu, Shih-Hsiung

2013-01-01

Teacher professional development (TPD) can benefit teachers in classrooms. This study contributes to an understanding of TPD processes where there is sufficient technology integration through teacher participation in a school-based community. It assesses the effectiveness of TPD and its potential problems. Qualitative research methods are used to…

49 CFR 230.24 - Maximum allowable stress.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Maximum allowable stress. 230.24 Section 230.24... Allowable Stress § 230.24 Maximum allowable stress. (a) Maximum allowable stress value. The maximum allowable stress value on any component of a steam locomotive boiler shall not exceed 1/4 of the ultimate...

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Energy Technology Data Exchange (ETDEWEB)

Muhida, Riza [Osaka Univ., Dept. of Physical Science, Toyonaka, Osaka (Japan); Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Park, Minwon; Dakkak, Mohammed; Matsuura, Kenji [Osaka Univ., Dept. of Electrical Engineering, Suita, Osaka (Japan); Tsuyoshi, Akira; Michira, Masakazu [Kobe City College of Technology, Nishi-ku, Kobe (Japan)

2003-02-01

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented. Based on the characteristics of voltage-current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC-DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously. This method uses a proportional integrator controller to control the duty factor of DC-DC converter with pulse-width modulator (PWM). The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment. (Author)

The individual in the collaborative

DEFF Research Database (Denmark)

Møller, Hanne; Skott, Charlotte Krog

Potentials of Lesson Study (LS) as a method for teachers’ professional development (TPD) are well documented and convincing in the form of both examples from Japan and LS’s embodiment of identified principles for promising TPD approaches (Hennessy, 2014), such as teacher collaboration and an expe......Potentials of Lesson Study (LS) as a method for teachers’ professional development (TPD) are well documented and convincing in the form of both examples from Japan and LS’s embodiment of identified principles for promising TPD approaches (Hennessy, 2014), such as teacher collaboration...

Nuclear EMP: key suppression device parameters for EMP hardening

International Nuclear Information System (INIS)

Durgin, D.L.; Brown, R.M.

1975-03-01

The electrical transients induced by EMP exhibit unique characteristics which differ considerably from transients associated with other phenomena such as lightning, switching, and circuit malfunctions. The suppression techniques developed to handle more common transients, though not necessarily the same devices, can be used for EMP damage protection. The suppression devices used for circuit level EMP protection are referred to as Terminal Protection Devices (TPD). Little detailed data describing the response of TPD's to EMP-related transients have been published. While most vendors publish specifications for TPD performance, there is little standardization of parameters and TPD response models are not available. This lack of parameter standardization has resulted in a proliferation of test data that is sometimes conflicting and often not directly comparable. This paper derives and/or defines a consistent set of parameters based on EMP circuit hardening requirements and on measurable component parameters and is concerned only with use of TPD's to prevent permanent damage. Three sets of parameters pertaining to pertinent TPD functional characteristics were defined as follows: standby parameters, protection parameters, and failure parameters. These parameters are used to evaluate a representative sample of TPD's and the results are presented in matrix form to facilitate the selection of devices for specific hardening problems

Tumor protein D52 expression is post-transcriptionally regulated by T-cell intercellular antigen (TIA) 1 and TIA-related protein via mRNA stability.

Science.gov (United States)

Motohashi, Hiromi; Mukudai, Yoshiki; Ito, Chihiro; Kato, Kosuke; Shimane, Toshikazu; Kondo, Seiji; Shirota, Tatsuo

2017-05-04

Although tumor protein D52 (TPD52) family proteins were first identified nearly 20 years ago, their molecular regulatory mechanisms remain unclear. Therefore, we investigated the post-transcriptional regulation of TPD52 family genes. An RNA immunoprecipitation (RIP) assay showed the potential binding ability of TPD52 family mRNAs to several RNA-binding proteins, and an RNA degradation assay revealed that TPD52 is subject to more prominent post-transcriptional regulation than are TPD53 and TPD54. We subsequently focused on the 3'-untranslated region (3'-UTR) of TPD52 as a cis -acting element in post-transcriptional gene regulation. Several deletion mutants of the 3'-UTR of TPD52 mRNA were constructed and ligated to the 3'-end of a reporter green fluorescence protein gene. An RNA degradation assay revealed that a minimal cis -acting region, located in the 78-280 region of the 5'-proximal region of the 3'-UTR, stabilized the reporter mRNA. Biotin pull-down and RIP assays revealed specific binding of the region to T-cell intracellular antigen 1 (TIA-1) and TIA-1-related protein (TIAR). Knockdown of TIA-1/TIAR decreased not only the expression, but also the stability of TPD52 mRNA; it also decreased the expression and stability of the reporter gene ligated to the 3'-end of the 78-280 fragment. Stimulation of transforming growth factor-β and epidermal growth factor decreased the binding ability of these factors, resulting in decreased mRNA stability. These results indicate that the 78-280 fragment and TIA-1/TIAR concordantly contribute to mRNA stability as a cis -acting element and trans -acting factor(s), respectively. Thus, we here report the specific interactions between these elements in the post-transcriptional regulation of the TPD52 gene. © 2017 The Author(s); published by Portland Press Limited on behalf of the Biochemical Society.

Lake Basin Fetch and Maximum Length/Width

Data.gov (United States)

Minnesota Department of Natural Resources — Linear features representing the Fetch, Maximum Length and Maximum Width of a lake basin. Fetch, maximum length and average width are calcuated from the lake polygon...

Maximum permissible voltage of YBCO coated conductors

Energy Technology Data Exchange (ETDEWEB)

Wen, J.; Lin, B.; Sheng, J.; Xu, J.; Jin, Z. [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Hong, Z., E-mail: zhiyong.hong@sjtu.edu.cn [Department of Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China); Wang, D.; Zhou, H.; Shen, X.; Shen, C. [Qingpu Power Supply Company, State Grid Shanghai Municipal Electric Power Company, Shanghai (China)

2014-06-15

Highlights: • We examine three kinds of tapes’ maximum permissible voltage. • We examine the relationship between quenching duration and maximum permissible voltage. • Continuous I{sub c} degradations under repetitive quenching where tapes reaching maximum permissible voltage. • The relationship between maximum permissible voltage and resistance, temperature. - Abstract: Superconducting fault current limiter (SFCL) could reduce short circuit currents in electrical power system. One of the most important thing in developing SFCL is to find out the maximum permissible voltage of each limiting element. The maximum permissible voltage is defined as the maximum voltage per unit length at which the YBCO coated conductors (CC) do not suffer from critical current (I{sub c}) degradation or burnout. In this research, the time of quenching process is changed and voltage is raised until the I{sub c} degradation or burnout happens. YBCO coated conductors test in the experiment are from American superconductor (AMSC) and Shanghai Jiao Tong University (SJTU). Along with the quenching duration increasing, the maximum permissible voltage of CC decreases. When quenching duration is 100 ms, the maximum permissible of SJTU CC, 12 mm AMSC CC and 4 mm AMSC CC are 0.72 V/cm, 0.52 V/cm and 1.2 V/cm respectively. Based on the results of samples, the whole length of CCs used in the design of a SFCL can be determined.

Receiver function estimated by maximum entropy deconvolution

Institute of Scientific and Technical Information of China (English)

吴庆举; 田小波; 张乃铃; 李卫平; 曾融生

2003-01-01

Maximum entropy deconvolution is presented to estimate receiver function, with the maximum entropy as the rule to determine auto-correlation and cross-correlation functions. The Toeplitz equation and Levinson algorithm are used to calculate the iterative formula of error-predicting filter, and receiver function is then estimated. During extrapolation, reflective coefficient is always less than 1, which keeps maximum entropy deconvolution stable. The maximum entropy of the data outside window increases the resolution of receiver function. Both synthetic and real seismograms show that maximum entropy deconvolution is an effective method to measure receiver function in time-domain.

MRI of traumatic patellar dislocation in children

Energy Technology Data Exchange (ETDEWEB)

Zaidi, A.; Cole, W. [Hospital for Sick Children, Toronto (Canada). Diagnostic Imaging; Babyn, P. [Mater Children' s, Brisbane (Australia). Paediatric Orthopaedic Surgery; Astori, I. [Univ. of Toronto (Canada). Diagnostic Imaging; White, L. [Hospital for Sick Children, Toronto (Canada). Orthopaedic Surgery; Doria, A.

2006-11-15

Traumatic patellar dislocations (TPD) are common injuries in children, and MRI is useful in evaluation of pediatric musculoskeletal injuries. However, no pediatric studies on the MR features of TPD have been reported. To review the injuries after TPD in children. Patients with clinical or radiological recognition of TPD and those with suggestive MR findings were selected. Bone, cartilage and soft-tissue injuries and patellofemoral relationships were assessed. Results A total of 26 patients (age range 10-18 years) were identified. The following injuries were seen: bone bruising of the inferomedial patella (81% of patients) and the lateral femoral condyle (81% of patients), cartilage injuries of the inferomedial patella (38% of patients) and the lateral femoral condyle (38% of patients), osteochondral fragments (42% of patients) and injuries of the medial patellar restraints (81% of patients). Pediatric manifestations of TPD seen on MRI are similar to those in adults. TPD is often occult in children. Early recognition of bone bruising of the patella and lateral femoral condyle, associated osteochondral injuries, and medial patellar stabilizer injury is important for timely diagnosis.

MRI of traumatic patellar dislocation in children

International Nuclear Information System (INIS)

Zaidi, A.; Cole, W.; Babyn, P.; Astori, I.; White, L.; Doria, A.

2006-01-01

Traumatic patellar dislocations (TPD) are common injuries in children, and MRI is useful in evaluation of pediatric musculoskeletal injuries. However, no pediatric studies on the MR features of TPD have been reported. To review the injuries after TPD in children. Patients with clinical or radiological recognition of TPD and those with suggestive MR findings were selected. Bone, cartilage and soft-tissue injuries and patellofemoral relationships were assessed. Results A total of 26 patients (age range 10-18 years) were identified. The following injuries were seen: bone bruising of the inferomedial patella (81% of patients) and the lateral femoral condyle (81% of patients), cartilage injuries of the inferomedial patella (38% of patients) and the lateral femoral condyle (38% of patients), osteochondral fragments (42% of patients) and injuries of the medial patellar restraints (81% of patients). Pediatric manifestations of TPD seen on MRI are similar to those in adults. TPD is often occult in children. Early recognition of bone bruising of the patella and lateral femoral condyle, associated osteochondral injuries, and medial patellar stabilizer injury is important for timely diagnosis

Maximum Gene-Support Tree

Directory of Open Access Journals (Sweden)

Yunfeng Shan

2008-01-01

Full Text Available Genomes and genes diversify during evolution; however, it is unclear to what extent genes still retain the relationship among species. Model species for molecular phylogenetic studies include yeasts and viruses whose genomes were sequenced as well as plants that have the fossil-supported true phylogenetic trees available. In this study, we generated single gene trees of seven yeast species as well as single gene trees of nine baculovirus species using all the orthologous genes among the species compared. Homologous genes among seven known plants were used for validation of the finding. Four algorithms—maximum parsimony (MP, minimum evolution (ME, maximum likelihood (ML, and neighbor-joining (NJ—were used. Trees were reconstructed before and after weighting the DNA and protein sequence lengths among genes. Rarely a gene can always generate the “true tree” by all the four algorithms. However, the most frequent gene tree, termed “maximum gene-support tree” (MGS tree, or WMGS tree for the weighted one, in yeasts, baculoviruses, or plants was consistently found to be the “true tree” among the species. The results provide insights into the overall degree of divergence of orthologous genes of the genomes analyzed and suggest the following: 1 The true tree relationship among the species studied is still maintained by the largest group of orthologous genes; 2 There are usually more orthologous genes with higher similarities between genetically closer species than between genetically more distant ones; and 3 The maximum gene-support tree reflects the phylogenetic relationship among species in comparison.

Maximum neutron flux in thermal reactors

International Nuclear Information System (INIS)

Strugar, P.V.

1968-12-01

Direct approach to the problem is to calculate spatial distribution of fuel concentration if the reactor core directly using the condition of maximum neutron flux and comply with thermal limitations. This paper proved that the problem can be solved by applying the variational calculus, i.e. by using the maximum principle of Pontryagin. Mathematical model of reactor core is based on the two-group neutron diffusion theory with some simplifications which make it appropriate from maximum principle point of view. Here applied theory of maximum principle are suitable for application. The solution of optimum distribution of fuel concentration in the reactor core is obtained in explicit analytical form. The reactor critical dimensions are roots of a system of nonlinear equations and verification of optimum conditions can be done only for specific examples

75 FR 43840 - Inflation Adjustment of the Ordinary Maximum and Aggravated Maximum Civil Monetary Penalties for...

Science.gov (United States)

2010-07-27

...-17530; Notice No. 2] RIN 2130-ZA03 Inflation Adjustment of the Ordinary Maximum and Aggravated Maximum... remains at $250. These adjustments are required by the Federal Civil Penalties Inflation Adjustment Act [email protected] . SUPPLEMENTARY INFORMATION: The Federal Civil Penalties Inflation Adjustment Act of 1990...

Half-width at half-maximum, full-width at half-maximum analysis

Indian Academy of Sciences (India)

addition to the well-defined parameter full-width at half-maximum (FWHM). The distribution of ... optical side-lobes in the diffraction pattern resulting in steep central maxima [6], reduc- tion of effects of ... and broad central peak. The idea of.

Two-dimensional maximum entropy image restoration

International Nuclear Information System (INIS)

Brolley, J.E.; Lazarus, R.B.; Suydam, B.R.; Trussell, H.J.

1977-07-01

An optical check problem was constructed to test P LOG P maximum entropy restoration of an extremely distorted image. Useful recovery of the original image was obtained. Comparison with maximum a posteriori restoration is made. 7 figures

Maximum power point tracking

International Nuclear Information System (INIS)

Enslin, J.H.R.

1990-01-01

A well engineered renewable remote energy system, utilizing the principal of Maximum Power Point Tracking can be m ore cost effective, has a higher reliability and can improve the quality of life in remote areas. This paper reports that a high-efficient power electronic converter, for converting the output voltage of a solar panel, or wind generator, to the required DC battery bus voltage has been realized. The converter is controlled to track the maximum power point of the input source under varying input and output parameters. Maximum power point tracking for relative small systems is achieved by maximization of the output current in a battery charging regulator, using an optimized hill-climbing, inexpensive microprocessor based algorithm. Through practical field measurements it is shown that a minimum input source saving of 15% on 3-5 kWh/day systems can easily be achieved. A total cost saving of at least 10-15% on the capital cost of these systems are achievable for relative small rating Remote Area Power Supply systems. The advantages at larger temperature variations and larger power rated systems are much higher. Other advantages include optimal sizing and system monitor and control

7 CFR 3565.210 - Maximum interest rate.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Maximum interest rate. 3565.210 Section 3565.210... AGRICULTURE GUARANTEED RURAL RENTAL HOUSING PROGRAM Loan Requirements § 3565.210 Maximum interest rate. The interest rate for a guaranteed loan must not exceed the maximum allowable rate specified by the Agency in...

MXLKID: a maximum likelihood parameter identifier

International Nuclear Information System (INIS)

Gavel, D.T.

1980-07-01

MXLKID (MaXimum LiKelihood IDentifier) is a computer program designed to identify unknown parameters in a nonlinear dynamic system. Using noisy measurement data from the system, the maximum likelihood identifier computes a likelihood function (LF). Identification of system parameters is accomplished by maximizing the LF with respect to the parameters. The main body of this report briefly summarizes the maximum likelihood technique and gives instructions and examples for running the MXLKID program. MXLKID is implemented LRLTRAN on the CDC7600 computer at LLNL. A detailed mathematical description of the algorithm is given in the appendices. 24 figures, 6 tables

Usefulness of corregistration and post-processing of MR and interictal SPECT images for localization of epileptogenic focus in children – preliminary report

International Nuclear Information System (INIS)

Miśko, Jolanta; Jurkiewicz, Elżbieta; Bekiesińska-Figatowska, Monika; Kamińska, Anna; Bachański, Zbigniew; Chełstowska, Sylwia; Walecki, Jerzy

2011-01-01

Children with focal epilepsy unresponsive to anticonvulsant therapy may become surgical candidates. Inter-ictal SPECT (SPECT-IN) studies demonstrate an area of hypoperfusion within the seizure focus in up to 50% of patients. The goal of this study was to evaluate the usefulness of corregistration of MR and SPECT-IN images for localization of the epileptogenic focus. Brain MRI and SPECT-IN were performed in 20 children (mean age 9.5). We found multifocal (3–6 perfusion deficits in 10 patients) or diffuse perfusion deficits (lobar) in all patients. In fused MR and SPECT images we evaluated average activity in volumes-of-interest (VOIs) outlined in each gray matter region with deficits. Average VOI activity below average total brain activity with at least 15% difference to the mirror VOI in the brain cortex on the opposite side of was considered as “true” perfusion deficit (TPD). In all children from our group, MRI and SPECT-IN image fusion and evaluation of TPD allowed to verify most of multifocal or diffuse deficits: in each of 12 patients we found 1 TPD, in each of 6 patients 2 TPD and in each of 2 patients 3 TPD. In 8 patients with 2 or 3 TPD we used scalp EEG or ictal SPECT for identification of one probable location of epileptogenic focus. In children with refractory focal epilepsy, image fusion of MRI and SPECT-IN with evaluation of TPD has potential clinical utility in localization of epileptogenic focus

MOOCs for Teacher Professional Development: Reflections and Suggested Actions

Directory of Open Access Journals (Sweden)

Pradeep Kumar Misra

2018-02-01

Full Text Available Teacher Professional Development (TPD has become a major policy priority within education systems worldwide. But keeping teachers professionally up-to-date and providing them professional development opportunities on continuing basis is a big challenge. Massive Open Online Courses (MOOCs can be a cost and resource effective means to complement the traditional methods of professional development of teachers. This optimism is based on the assumption that use of MOOCs will facilitate mass training of teachers as per their convenience and ease. The other assumption is that being MOOCs-based training, it will be easy to adapt it to different cultures and languages. Considering these assumptions, this concept paper which is based on reviews of different reports, documents and research papers - discusses the challenges of TPD, reflects upon promises of using MOOCs for TPD; details initiatives and experiences of using MOOCs for TPD; and suggests actions for promoting the use of MOOCs for TPD.

78 FR 9845 - Minimum and Ordinary Maximum and Aggravated Maximum Civil Monetary Penalties for a Violation of...

Science.gov (United States)

2013-02-12

... maximum penalty amount of $75,000 for each violation, except that if the violation results in death... the maximum civil penalty for a violation is $175,000 if the violation results in death, serious... Penalties for a Violation of the Hazardous Materials Transportation Laws or Regulations, Orders, Special...

Characterisation of different hole transport materials as used in organic p-i-n solar cells

Energy Technology Data Exchange (ETDEWEB)

Pfuetzner, Steffen; Petrich, Annette; Koch, Maik; Riede, Moritz; Leo, Karl [Institut fuer Angewandte Photophysik, Technische Universitaet Dresden (Germany); Malbrich, Christine [Leibniz-Institut fuer Festkoerper- und Werkstoffforschung, Dresden (Germany); Hildebrandt, Dirk; Pfeiffer, Martin [Heliatek GmbH, Dresden (Germany)

2008-07-01

This work focuses on the replacement of hole transport material MeO-TPD, which has been used so far in organic p-i-n- solar cells despite its has unfavourable behaviour at elevated temperatures. For this reason, different characterisation and investigations of the hole transport materials PV-TPD, PV-TPDoM, Di-NPB and MeO-Spiro-TPD were done, i.e. dopability, hole mobility, absorption, reflection, cyclic voltametry and glass transition temperature were measured. With simplified structures, e.g. m-i-p diodes, and simplified solar cells, consisting of the blue absorbing fullerene C{sub 60} as acceptor and the transparent donor material 4P-TPD, further specific material properties were determined.

Performance analysis and comparison of an Atkinson cycle coupled to variable temperature heat reservoirs under maximum power and maximum power density conditions

International Nuclear Information System (INIS)

Wang, P.-Y.; Hou, S.-S.

2005-01-01

In this paper, performance analysis and comparison based on the maximum power and maximum power density conditions have been conducted for an Atkinson cycle coupled to variable temperature heat reservoirs. The Atkinson cycle is internally reversible but externally irreversible, since there is external irreversibility of heat transfer during the processes of constant volume heat addition and constant pressure heat rejection. This study is based purely on classical thermodynamic analysis methodology. It should be especially emphasized that all the results and conclusions are based on classical thermodynamics. The power density, defined as the ratio of power output to maximum specific volume in the cycle, is taken as the optimization objective because it considers the effects of engine size as related to investment cost. The results show that an engine design based on maximum power density with constant effectiveness of the hot and cold side heat exchangers or constant inlet temperature ratio of the heat reservoirs will have smaller size but higher efficiency, compression ratio, expansion ratio and maximum temperature than one based on maximum power. From the view points of engine size and thermal efficiency, an engine design based on maximum power density is better than one based on maximum power conditions. However, due to the higher compression ratio and maximum temperature in the cycle, an engine design based on maximum power density conditions requires tougher materials for engine construction than one based on maximum power conditions

LCLS Maximum Credible Beam Power

International Nuclear Information System (INIS)

Clendenin, J.

2005-01-01

The maximum credible beam power is defined as the highest credible average beam power that the accelerator can deliver to the point in question, given the laws of physics, the beam line design, and assuming all protection devices have failed. For a new accelerator project, the official maximum credible beam power is determined by project staff in consultation with the Radiation Physics Department, after examining the arguments and evidence presented by the appropriate accelerator physicist(s) and beam line engineers. The definitive parameter becomes part of the project's safety envelope. This technical note will first review the studies that were done for the Gun Test Facility (GTF) at SSRL, where a photoinjector similar to the one proposed for the LCLS is being tested. In Section 3 the maximum charge out of the gun for a single rf pulse is calculated. In Section 4, PARMELA simulations are used to track the beam from the gun to the end of the photoinjector. Finally in Section 5 the beam through the matching section and injected into Linac-1 is discussed

Influence of cell dissociation procedures on the tumorigenicity of Simian Virus 40 transformed fibroblasts

International Nuclear Information System (INIS)

Tenforde, T.S.; Risius, J.; Beckmann, A.; Tobias, C.A.; Gurney, E.

1975-11-01

Mouse fibroblasts transformed by Simian Virus 40 (SV40) were examined for tumor forming ability in syngeneic BALB/c mice following dissociation from tissue culture dishes by two procedures. A significantly greater in vivo proliferative capacity was observed for cells dissociated by the tryspin-EDTA procedure, with the injected cell dose for tumor production in 50 percent of recipient mice (the TPD 50 ) being 16-fold lower than the TPD 50 for cells dissociated by the EDTA procedure. Host immunosuppression with 300 rad whole-body γ irradiation led to a significant 7-fold decrease in the TPD 50 for cells dissociated by the EDTA procedure, while no significant decrease in TPD 50 was observed for cells dissociated by the tryspin-EDTA procedure

13 CFR 107.840 - Maximum term of Financing.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Maximum term of Financing. 107.840... COMPANIES Financing of Small Businesses by Licensees Structuring Licensee's Financing of An Eligible Small Business: Terms and Conditions of Financing § 107.840 Maximum term of Financing. The maximum term of any...

20 CFR 226.52 - Total annuity subject to maximum.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Total annuity subject to maximum. 226.52... COMPUTING EMPLOYEE, SPOUSE, AND DIVORCED SPOUSE ANNUITIES Railroad Retirement Family Maximum § 226.52 Total annuity subject to maximum. The total annuity amount which is compared to the maximum monthly amount to...

Study of optimum propellant production facilities for launch of space shuttle vehicles

Science.gov (United States)

Laclair, L. M.

1970-01-01

An integrated propellant manufacturing plant and distribution system located at Kennedy Space Center is studied. The initial planned propellant and pressurant production amounted to 160 tons/day (TPD) LH2, 10 TPD GH2, 800 TPD LO2, 400 TPD LN2, and 120 TPD GN2. This was based on a shuttle launch frequency of 104 per year. During the study, developments occurred which may lower cryogen requirements. A variety of plant and processing equipment sizes and costs are considered for redundancy and supply level considerations. Steam reforming is compared to partial oxidation as a means of generating hydrogen. Electric motors, steam turbines, and gas turbines are evaluated for driving compression equipment. Various sites on and off Government property are considered to determine tradeoffs between costs and problems directly associated with the site, product delivery and storage costs, raw material costs, and energy costs. Coproduction of other products such as deuterium, methanol, and ammonia are considered. Legal questions are discussed concerning a private company's liabilities and its rights to market commercial products under Government tax and cost shelters.

Maximum likely scale estimation

DEFF Research Database (Denmark)

Loog, Marco; Pedersen, Kim Steenstrup; Markussen, Bo

2005-01-01

A maximum likelihood local scale estimation principle is presented. An actual implementation of the estimation principle uses second order moments of multiple measurements at a fixed location in the image. These measurements consist of Gaussian derivatives possibly taken at several scales and/or ...

Maximum gravitational redshift of white dwarfs

International Nuclear Information System (INIS)

Shapiro, S.L.; Teukolsky, S.A.

1976-01-01

The stability of uniformly rotating, cold white dwarfs is examined in the framework of the Parametrized Post-Newtonian (PPN) formalism of Will and Nordtvedt. The maximum central density and gravitational redshift of a white dwarf are determined as functions of five of the nine PPN parameters (γ, β, zeta 2 , zeta 3 , and zeta 4 ), the total angular momentum J, and the composition of the star. General relativity predicts that the maximum redshifts is 571 km s -1 for nonrotating carbon and helium dwarfs, but is lower for stars composed of heavier nuclei. Uniform rotation can increase the maximum redshift to 647 km s -1 for carbon stars (the neutronization limit) and to 893 km s -1 for helium stars (the uniform rotation limit). The redshift distribution of a larger sample of white dwarfs may help determine the composition of their cores

Revealing the Maximum Strength in Nanotwinned Copper

DEFF Research Database (Denmark)

Lu, L.; Chen, X.; Huang, Xiaoxu

2009-01-01

boundary–related processes. We investigated the maximum strength of nanotwinned copper samples with different twin thicknesses. We found that the strength increases with decreasing twin thickness, reaching a maximum at 15 nanometers, followed by a softening at smaller values that is accompanied by enhanced...

49 CFR 195.406 - Maximum operating pressure.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Maximum operating pressure. 195.406 Section 195.406 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS... HAZARDOUS LIQUIDS BY PIPELINE Operation and Maintenance § 195.406 Maximum operating pressure. (a) Except for...

Improved efficacy of cisplatin in combination with a nano-formulation of pentacyclic triterpenediol

Energy Technology Data Exchange (ETDEWEB)

Alam, Noor [Formulation & Drug Delivery Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Qayum, Arem; Kumar, Ashok [Academy of Scientific and Innovative Research (AcSIR), Anusandhan Bhawan, 2 Rafi Marg, New Delhi 110001 (India); Cancer Pharmacology Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Khare, Vaibhav [Formulation & Drug Delivery Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Sharma, Parduman Raj [Cancer Pharmacology Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Andotra, Samar Singh [Natural Product Chemistry Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Singh, Shashank K. [Academy of Scientific and Innovative Research (AcSIR), Anusandhan Bhawan, 2 Rafi Marg, New Delhi 110001 (India); Cancer Pharmacology Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Koul, Surinder, E-mail: skoul@iiim.ac.in [Natural Product Chemistry Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India); Gupta, Prem N., E-mail: pngupta10@gmail.com [Academy of Scientific and Innovative Research (AcSIR), Anusandhan Bhawan, 2 Rafi Marg, New Delhi 110001 (India); Formulation & Drug Delivery Division, CSIR-Indian Institute of Integrative Medicine, Canal Road, Jammu 180001 (India)

2016-11-01

Cisplatin is widely used for the treatment of various cancers including cervical, ovarian, lung and head and neck, however, its clinical success is limited owing to the dose-dependent adverse effects, mainly nephrotoxicity and neurotoxicity. In order to address this limitation, the present study was undertaken to investigate growth inhibitory effect of cisplatin in combination with a triterpenediol (3a, 24-dihydroxyurs-12-ene and 3a, 24-dihydroxyolean-12-ene, TPD) on human ovarian cancer cell line. Poly(dl-lactic-co-glycolic) acid nanoparticles loaded with TPD (TPD-PLGA-NPs) were successfully developed by emulsion solvent evaporation method. The TPD-PLGA-NPs were characterized for size distribution and zeta potential which was in order of 152.56 ± 3.01 nm and − 17.36 ± 0.37 mV respectively. The morphological evaluation was carried out by transmission electron microscopy and the formulation was also characterized using Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The drug loading of the optimized formulation was 51.03 ± 1.52 μg/mg and the formulation exhibited sustained drug release profile. The in vitro cellular uptake study of coumarin-6 loaded PLGA nanoparticles in OVCAR-5 cells demonstrated a time dependent increase in uptake efficiency. Further, growth inhibitory effect of cisplatin was investigated in combination with TPD-PLGA-NPs. The combination index (CI) was < 1, indicating a synergistic interaction. Further, at 75% of cell growth inhibition (ED{sub 75}) the dose of cisplatin was reduced to 3.8 folds using this combination. The results indicated the potential of cisplatin and TPD-PLGA-NPs combination in order to reduce to dose limiting toxicities of the former. - Highlights: • TPD nanoparticles showed a time dependent increase in cellular uptake efficiency. • TPD nanoparticles showed synergistic interaction between cisplatin. • The dose of cisplatin was reduced to 3.8 folds using this combination

Maximum spectral demands in the near-fault region

Science.gov (United States)

Huang, Yin-Nan; Whittaker, Andrew S.; Luco, Nicolas

2008-01-01

The Next Generation Attenuation (NGA) relationships for shallow crustal earthquakes in the western United States predict a rotated geometric mean of horizontal spectral demand, termed GMRotI50, and not maximum spectral demand. Differences between strike-normal, strike-parallel, geometric-mean, and maximum spectral demands in the near-fault region are investigated using 147 pairs of records selected from the NGA strong motion database. The selected records are for earthquakes with moment magnitude greater than 6.5 and for closest site-to-fault distance less than 15 km. Ratios of maximum spectral demand to NGA-predicted GMRotI50 for each pair of ground motions are presented. The ratio shows a clear dependence on period and the Somerville directivity parameters. Maximum demands can substantially exceed NGA-predicted GMRotI50 demands in the near-fault region, which has significant implications for seismic design, seismic performance assessment, and the next-generation seismic design maps. Strike-normal spectral demands are a significantly unconservative surrogate for maximum spectral demands for closest distance greater than 3 to 5 km. Scale factors that transform NGA-predicted GMRotI50 to a maximum spectral demand in the near-fault region are proposed.

Maximum allowable load on wheeled mobile manipulators

International Nuclear Information System (INIS)

Habibnejad Korayem, M.; Ghariblu, H.

2003-01-01

This paper develops a computational technique for finding the maximum allowable load of mobile manipulator during a given trajectory. The maximum allowable loads which can be achieved by a mobile manipulator during a given trajectory are limited by the number of factors; probably the dynamic properties of mobile base and mounted manipulator, their actuator limitations and additional constraints applied to resolving the redundancy are the most important factors. To resolve extra D.O.F introduced by the base mobility, additional constraint functions are proposed directly in the task space of mobile manipulator. Finally, in two numerical examples involving a two-link planar manipulator mounted on a differentially driven mobile base, application of the method to determining maximum allowable load is verified. The simulation results demonstrates the maximum allowable load on a desired trajectory has not a unique value and directly depends on the additional constraint functions which applies to resolve the motion redundancy

Robust Maximum Association Estimators

NARCIS (Netherlands)

A. Alfons (Andreas); C. Croux (Christophe); P. Filzmoser (Peter)

2017-01-01

textabstractThe maximum association between two multivariate variables X and Y is defined as the maximal value that a bivariate association measure between one-dimensional projections αX and αY can attain. Taking the Pearson correlation as projection index results in the first canonical correlation

Selection of the Maximum Spatial Cluster Size of the Spatial Scan Statistic by Using the Maximum Clustering Set-Proportion Statistic.

Science.gov (United States)

Ma, Yue; Yin, Fei; Zhang, Tao; Zhou, Xiaohua Andrew; Li, Xiaosong

2016-01-01

Spatial scan statistics are widely used in various fields. The performance of these statistics is influenced by parameters, such as maximum spatial cluster size, and can be improved by parameter selection using performance measures. Current performance measures are based on the presence of clusters and are thus inapplicable to data sets without known clusters. In this work, we propose a novel overall performance measure called maximum clustering set-proportion (MCS-P), which is based on the likelihood of the union of detected clusters and the applied dataset. MCS-P was compared with existing performance measures in a simulation study to select the maximum spatial cluster size. Results of other performance measures, such as sensitivity and misclassification, suggest that the spatial scan statistic achieves accurate results in most scenarios with the maximum spatial cluster sizes selected using MCS-P. Given that previously known clusters are not required in the proposed strategy, selection of the optimal maximum cluster size with MCS-P can improve the performance of the scan statistic in applications without identified clusters.

Maximum-Likelihood Detection Of Noncoherent CPM

Science.gov (United States)

Divsalar, Dariush; Simon, Marvin K.

1993-01-01

Simplified detectors proposed for use in maximum-likelihood-sequence detection of symbols in alphabet of size M transmitted by uncoded, full-response continuous phase modulation over radio channel with additive white Gaussian noise. Structures of receivers derived from particular interpretation of maximum-likelihood metrics. Receivers include front ends, structures of which depends only on M, analogous to those in receivers of coherent CPM. Parts of receivers following front ends have structures, complexity of which would depend on N.

Maximum Entropy Fundamentals

Directory of Open Access Journals (Sweden)

F. Topsøe

2001-09-01

Full Text Available Abstract: In its modern formulation, the Maximum Entropy Principle was promoted by E.T. Jaynes, starting in the mid-fifties. The principle dictates that one should look for a distribution, consistent with available information, which maximizes the entropy. However, this principle focuses only on distributions and it appears advantageous to bring information theoretical thinking more prominently into play by also focusing on the "observer" and on coding. This view was brought forward by the second named author in the late seventies and is the view we will follow-up on here. It leads to the consideration of a certain game, the Code Length Game and, via standard game theoretical thinking, to a principle of Game Theoretical Equilibrium. This principle is more basic than the Maximum Entropy Principle in the sense that the search for one type of optimal strategies in the Code Length Game translates directly into the search for distributions with maximum entropy. In the present paper we offer a self-contained and comprehensive treatment of fundamentals of both principles mentioned, based on a study of the Code Length Game. Though new concepts and results are presented, the reading should be instructional and accessible to a rather wide audience, at least if certain mathematical details are left aside at a rst reading. The most frequently studied instance of entropy maximization pertains to the Mean Energy Model which involves a moment constraint related to a given function, here taken to represent "energy". This type of application is very well known from the literature with hundreds of applications pertaining to several different elds and will also here serve as important illustration of the theory. But our approach reaches further, especially regarding the study of continuity properties of the entropy function, and this leads to new results which allow a discussion of models with so-called entropy loss. These results have tempted us to speculate over

22 CFR 201.67 - Maximum freight charges.

Science.gov (United States)

2010-04-01

..., commodity rate classification, quantity, vessel flag category (U.S.-or foreign-flag), choice of ports, and... the United States. (2) Maximum charter rates. (i) USAID will not finance ocean freight under any... owner(s). (4) Maximum liner rates. USAID will not finance ocean freight for a cargo liner shipment at a...

Hydrogenolysis of 2-tosyloxy-1,3-propanediol into 1,3-propanediol over Raney Ni catalyst

Energy Technology Data Exchange (ETDEWEB)

Zhi, Zheng; Jianli, Wang; Zhen, Lu; Min, Luo; Miao, Zhang; Lixin, Xu; Jianbing [Zhejiang Province Key Laboratory of Biofuel, The State Key Laboratory Breeding Base of Green Chemistry-Synthesis Technology, Zhejiang University of Technology, Hangzhou (China)

2013-03-15

2-Tosyloxy-1,3-propanediol (TPD), a potential precursor for 1,3-propanediol (1,3-PD) production, is produced by the tosylation of glycerol with the help of protecting group techniques. In this work, the hydrogenolysis of TPD into 1,3-PD over Raney Ni catalyst is discussed at different reaction parameters to optimize the reaction conditions for selective formation of 1,3-PD. The mechanisms of the hydrogenolysis of TPD and the side reactions were also confirmed by gas chromatography-mass spectrometry (GC-MS) technique (author)

Determination of the maximum-depth to potential field sources by a maximum structural index method

Science.gov (United States)

Fedi, M.; Florio, G.

2013-01-01

A simple and fast determination of the limiting depth to the sources may represent a significant help to the data interpretation. To this end we explore the possibility of determining those source parameters shared by all the classes of models fitting the data. One approach is to determine the maximum depth-to-source compatible with the measured data, by using for example the well-known Bott-Smith rules. These rules involve only the knowledge of the field and its horizontal gradient maxima, and are independent from the density contrast. Thanks to the direct relationship between structural index and depth to sources we work out a simple and fast strategy to obtain the maximum depth by using the semi-automated methods, such as Euler deconvolution or depth-from-extreme-points method (DEXP). The proposed method consists in estimating the maximum depth as the one obtained for the highest allowable value of the structural index (Nmax). Nmax may be easily determined, since it depends only on the dimensionality of the problem (2D/3D) and on the nature of the analyzed field (e.g., gravity field or magnetic field). We tested our approach on synthetic models against the results obtained by the classical Bott-Smith formulas and the results are in fact very similar, confirming the validity of this method. However, while Bott-Smith formulas are restricted to the gravity field only, our method is applicable also to the magnetic field and to any derivative of the gravity and magnetic field. Our method yields a useful criterion to assess the source model based on the (∂f/∂x)max/fmax ratio. The usefulness of the method in real cases is demonstrated for a salt wall in the Mississippi basin, where the estimation of the maximum depth agrees with the seismic information.

40 CFR 141.13 - Maximum contaminant levels for turbidity.

Science.gov (United States)

2010-07-01

... turbidity. 141.13 Section 141.13 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Maximum contaminant levels for turbidity. The maximum contaminant levels for turbidity are applicable to... part. The maximum contaminant levels for turbidity in drinking water, measured at a representative...

Modelling maximum canopy conductance and transpiration in ...

African Journals Online (AJOL)

There is much current interest in predicting the maximum amount of water that can be transpired by Eucalyptus trees. It is possible that industrial waste water may be applied as irrigation water to eucalypts and it is important to predict the maximum transpiration rates of these plantations in an attempt to dispose of this ...

40 CFR 141.62 - Maximum contaminant levels for inorganic contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for inorganic contaminants. 141.62 Section 141.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Water Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.62 Maximum...

Weak scale from the maximum entropy principle

Science.gov (United States)

Hamada, Yuta; Kawai, Hikaru; Kawana, Kiyoharu

2015-03-01

The theory of the multiverse and wormholes suggests that the parameters of the Standard Model (SM) are fixed in such a way that the radiation of the S3 universe at the final stage S_rad becomes maximum, which we call the maximum entropy principle. Although it is difficult to confirm this principle generally, for a few parameters of the SM, we can check whether S_rad actually becomes maximum at the observed values. In this paper, we regard S_rad at the final stage as a function of the weak scale (the Higgs expectation value) vh, and show that it becomes maximum around vh = {{O}} (300 GeV) when the dimensionless couplings in the SM, i.e., the Higgs self-coupling, the gauge couplings, and the Yukawa couplings are fixed. Roughly speaking, we find that the weak scale is given by vh ˜ T_{BBN}2 / (M_{pl}ye5), where ye is the Yukawa coupling of electron, T_BBN is the temperature at which the Big Bang nucleosynthesis starts, and M_pl is the Planck mass.

A Conceptual Framework for Graduate Teaching Assistant Professional Development Evaluation and Research.

Science.gov (United States)

Reeves, Todd D; Marbach-Ad, Gili; Miller, Kristen R; Ridgway, Judith; Gardner, Grant E; Schussler, Elisabeth E; Wischusen, E William

2016-01-01

Biology graduate teaching assistants (GTAs) are significant contributors to the educational mission of universities, particularly in introductory courses, yet there is a lack of empirical data on how to best prepare them for their teaching roles. This essay proposes a conceptual framework for biology GTA teaching professional development (TPD) program evaluation and research with three overarching variable categories for consideration: outcome variables, contextual variables, and moderating variables. The framework's outcome variables go beyond GTA satisfaction and instead position GTA cognition, GTA teaching practice, and undergraduate learning outcomes as the foci of GTA TPD evaluation and research. For each GTA TPD outcome variable, key evaluation questions and example assessment instruments are introduced to demonstrate how the framework can be used to guide GTA TPD evaluation and research plans. A common conceptual framework is also essential to coordinating the collection and synthesis of empirical data on GTA TPD nationally. Thus, the proposed conceptual framework serves as both a guide for conducting GTA TPD evaluation at single institutions and as a means to coordinate research across institutions at a national level. © 2016 T. D. Reeves et al. CBE—Life Sciences Education © 2016 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

The Effect of the Crystalline Phase of Zirconia for the Dehydration of Iso-propanol

International Nuclear Information System (INIS)

Sim, Hye-In; Park, Jung-Hyun; Cho, Jun Hee; Ahn, Ji-Hye; Choi, Min-Seok; Shin, Chae-Ho

2013-01-01

Zirconium hydroxide was synthesized by varying the aging time of the zirconyl chloride octahydrate at 100 .deg. C in aqueous solution and the resulting hydroxides were calcined at 700 .deg. C for 6 h to obtain the crystalline ZrO 2 . The materials used in this study were characterized by differential thermal analysis (DTA), X-ray diffraction (XRD), N 2 -sorption, transmission electron microscopy (TEM), NH 3 temperature-programmed desorption (NH 3 -TPD), CO 2 -TPD and iso-propanol TPD analyses to correlate with catalytic activity for the dehydration of iso-propanol. The pure tetragonal ZrO 2 phase was obtained after 24 h aging of zirconium hydroxide and successive calcination at 700 .deg. C. The increase of aging time showed the production of smaller particle size ZrO 2 resulting that the higher specific surface area and total pore volume. NH 3 -TPD results revealed that the relative acidity of the catalysts increased along with the increase of aging time. On the other hand, the results of CO 2 -TPD showed the reverse trend of NH 3 -TPD results. The best catalytic activity for the dehydration of iso-propanol to propylene was shown over ZrO 2 catalyst aged for 168 h which had the highest S BET (178 m 2 g -1 ). The catalytic activity could be correlated with high surface area, relative acidity and easy desorption of iso-propanol

Accurate modeling and maximum power point detection of ...

African Journals Online (AJOL)

Accurate modeling and maximum power point detection of photovoltaic ... Determination of MPP enables the PV system to deliver maximum available power. ..... adaptive artificial neural network: Proposition for a new sizing procedure.

40 CFR 141.61 - Maximum contaminant levels for organic contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for organic contaminants. 141.61 Section 141.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.61 Maximum contaminant...

The power and robustness of maximum LOD score statistics.

Science.gov (United States)

Yoo, Y J; Mendell, N R

2008-07-01

The maximum LOD score statistic is extremely powerful for gene mapping when calculated using the correct genetic parameter value. When the mode of genetic transmission is unknown, the maximum of the LOD scores obtained using several genetic parameter values is reported. This latter statistic requires higher critical value than the maximum LOD score statistic calculated from a single genetic parameter value. In this paper, we compare the power of maximum LOD scores based on three fixed sets of genetic parameter values with the power of the LOD score obtained after maximizing over the entire range of genetic parameter values. We simulate family data under nine generating models. For generating models with non-zero phenocopy rates, LOD scores maximized over the entire range of genetic parameters yielded greater power than maximum LOD scores for fixed sets of parameter values with zero phenocopy rates. No maximum LOD score was consistently more powerful than the others for generating models with a zero phenocopy rate. The power loss of the LOD score maximized over the entire range of genetic parameters, relative to the maximum LOD score calculated using the correct genetic parameter value, appeared to be robust to the generating models.

Investigating the coverage dependent behaviour of CO on Gd/Pt(111)

DEFF Research Database (Denmark)

Ulrikkeholm, Elisabeth Therese; Hansen, Martin Hangaard; Rossmeisl, Jan

2016-01-01

diffraction (LEED), showing that a highly ordered crystal structure had appeared. To study the molecular dynamics on this surface a detailed study of the CO adsorption on the surface was conducted using temperature programmed desorption (TPD) of CO. The TPD spectra show a desorption peak shifted down...... in temperature compared to those of pure Pt(111). The shape of the desorption peak and the desorption temperature were shown to be strongly dependent on the CO coverage of the surface. A systematic investigation of CO desorption temperature as a function of coverage was consequently performed. A simple...... simulation of the TPD spectra was carried out, based on adsorption energies from density functional theory (DFT). This simulation reproduces the shift and the narrowing of the desorption spectrum from the experiments and the DFT calculations suggest that the sharp TPD feature arises from cooperative...

Maximum Power Training and Plyometrics for Cross-Country Running.

Science.gov (United States)

Ebben, William P.

2001-01-01

Provides a rationale for maximum power training and plyometrics as conditioning strategies for cross-country runners, examining: an evaluation of training methods (strength training and maximum power training and plyometrics); biomechanic and velocity specificity (role in preventing injury); and practical application of maximum power training and…

Microsystem with integrated capillary leak to mass spectrometer for high sensitivity temperature programmed desorption

DEFF Research Database (Denmark)

Quaade, Ulrich; Jensen, Søren; Hansen, Ole

2004-01-01

leak minimizes dead volumes in the system, resulting in increased sensitivity and reduced response time. These properties make the system ideal for TPD experiments in a carrier gas. With CO desorbing from platinum as model system, it is shown that CO desorbing in 105 Pa of argon from as little as 0.......5 cm2 of platinum foil gives a clear desorption peak. By using the microfabricated flow system, TPD experiments can be performed in a carrier gas with a sensitivity approaching that of TPD experiments in vacuum. ©2004 American Institute of Physics...

The last glacial maximum

Science.gov (United States)

Clark, P.U.; Dyke, A.S.; Shakun, J.D.; Carlson, A.E.; Clark, J.; Wohlfarth, B.; Mitrovica, J.X.; Hostetler, S.W.; McCabe, A.M.

2009-01-01

We used 5704 14C, 10Be, and 3He ages that span the interval from 10,000 to 50,000 years ago (10 to 50 ka) to constrain the timing of the Last Glacial Maximum (LGM) in terms of global ice-sheet and mountain-glacier extent. Growth of the ice sheets to their maximum positions occurred between 33.0 and 26.5 ka in response to climate forcing from decreases in northern summer insolation, tropical Pacific sea surface temperatures, and atmospheric CO2. Nearly all ice sheets were at their LGM positions from 26.5 ka to 19 to 20 ka, corresponding to minima in these forcings. The onset of Northern Hemisphere deglaciation 19 to 20 ka was induced by an increase in northern summer insolation, providing the source for an abrupt rise in sea level. The onset of deglaciation of the West Antarctic Ice Sheet occurred between 14 and 15 ka, consistent with evidence that this was the primary source for an abrupt rise in sea level ???14.5 ka.

Maximum physical capacity testing in cancer patients undergoing chemotherapy

DEFF Research Database (Denmark)

Knutsen, L.; Quist, M; Midtgaard, J

2006-01-01

BACKGROUND: Over the past few years there has been a growing interest in the field of physical exercise in rehabilitation of cancer patients, leading to requirements for objective maximum physical capacity measurement (maximum oxygen uptake (VO(2max)) and one-repetition maximum (1RM)) to determin...... early in the treatment process. However, the patients were self-referred and thus highly motivated and as such are not necessarily representative of the whole population of cancer patients treated with chemotherapy....... in performing maximum physical capacity tests as these motivated them through self-perceived competitiveness and set a standard that served to encourage peak performance. CONCLUSION: The positive attitudes in this sample towards maximum physical capacity open the possibility of introducing physical testing...

MAXIMUM PRINCIPLE FOR SUBSONIC FLOW WITH VARIABLE ENTROPY

Directory of Open Access Journals (Sweden)

B. Sizykh Grigory

2017-01-01

Full Text Available Maximum principle for subsonic flow is fair for stationary irrotational subsonic gas flows. According to this prin- ciple, if the value of the velocity is not constant everywhere, then its maximum is achieved on the boundary and only on the boundary of the considered domain. This property is used when designing form of an aircraft with a maximum critical val- ue of the Mach number: it is believed that if the local Mach number is less than unit in the incoming flow and on the body surface, then the Mach number is less then unit in all points of flow. The known proof of maximum principle for subsonic flow is based on the assumption that in the whole considered area of the flow the pressure is a function of density. For the ideal and perfect gas (the role of diffusion is negligible, and the Mendeleev-Clapeyron law is fulfilled, the pressure is a function of density if entropy is constant in the entire considered area of the flow. Shows an example of a stationary sub- sonic irrotational flow, in which the entropy has different values on different stream lines, and the pressure is not a function of density. The application of the maximum principle for subsonic flow with respect to such a flow would be unreasonable. This example shows the relevance of the question about the place of the points of maximum value of the velocity, if the entropy is not a constant. To clarify the regularities of the location of these points, was performed the analysis of the com- plete Euler equations (without any simplifying assumptions in 3-D case. The new proof of the maximum principle for sub- sonic flow was proposed. This proof does not rely on the assumption that the pressure is a function of density. Thus, it is shown that the maximum principle for subsonic flow is true for stationary subsonic irrotational flows of ideal perfect gas with variable entropy.

Maximum power point tracker based on fuzzy logic

International Nuclear Information System (INIS)

Daoud, A.; Midoun, A.

2006-01-01

The solar energy is used as power source in photovoltaic power systems and the need for an intelligent power management system is important to obtain the maximum power from the limited solar panels. With the changing of the sun illumination due to variation of angle of incidence of sun radiation and of the temperature of the panels, Maximum Power Point Tracker (MPPT) enables optimization of solar power generation. The MPPT is a sub-system designed to extract the maximum power from a power source. In the case of solar panels power source. the maximum power point varies as a result of changes in its electrical characteristics which in turn are functions of radiation dose, temperature, ageing and other effects. The MPPT maximum the power output from panels for a given set of conditions by detecting the best working point of the power characteristic and then controls the current through the panels or the voltage across them. Many MPPT methods have been reported in literature. These techniques of MPPT can be classified into three main categories that include: lookup table methods, hill climbing methods and computational methods. The techniques vary according to the degree of sophistication, processing time and memory requirements. The perturbation and observation algorithm (hill climbing technique) is commonly used due to its ease of implementation, and relative tracking efficiency. However, it has been shown that when the insolation changes rapidly, the perturbation and observation method is slow to track the maximum power point. In recent years, the fuzzy controllers are used for maximum power point tracking. This method only requires the linguistic control rules for maximum power point, the mathematical model is not required and therefore the implementation of this control method is easy to real control system. In this paper, we we present a simple robust MPPT using fuzzy set theory where the hardware consists of the microchip's microcontroller unit control card and

Maximum entropy methods

International Nuclear Information System (INIS)

Ponman, T.J.

1984-01-01

For some years now two different expressions have been in use for maximum entropy image restoration and there has been some controversy over which one is appropriate for a given problem. Here two further entropies are presented and it is argued that there is no single correct algorithm. The properties of the four different methods are compared using simple 1D simulations with a view to showing how they can be used together to gain as much information as possible about the original object. (orig.)

Maximum entropy deconvolution of low count nuclear medicine images

International Nuclear Information System (INIS)

McGrath, D.M.

1998-12-01

Maximum entropy is applied to the problem of deconvolving nuclear medicine images, with special consideration for very low count data. The physics of the formation of scintigraphic images is described, illustrating the phenomena which degrade planar estimates of the tracer distribution. Various techniques which are used to restore these images are reviewed, outlining the relative merits of each. The development and theoretical justification of maximum entropy as an image processing technique is discussed. Maximum entropy is then applied to the problem of planar deconvolution, highlighting the question of the choice of error parameters for low count data. A novel iterative version of the algorithm is suggested which allows the errors to be estimated from the predicted Poisson mean values. This method is shown to produce the exact results predicted by combining Poisson statistics and a Bayesian interpretation of the maximum entropy approach. A facility for total count preservation has also been incorporated, leading to improved quantification. In order to evaluate this iterative maximum entropy technique, two comparable methods, Wiener filtering and a novel Bayesian maximum likelihood expectation maximisation technique, were implemented. The comparison of results obtained indicated that this maximum entropy approach may produce equivalent or better measures of image quality than the compared methods, depending upon the accuracy of the system model used. The novel Bayesian maximum likelihood expectation maximisation technique was shown to be preferable over many existing maximum a posteriori methods due to its simplicity of implementation. A single parameter is required to define the Bayesian prior, which suppresses noise in the solution and may reduce the processing time substantially. Finally, maximum entropy deconvolution was applied as a pre-processing step in single photon emission computed tomography reconstruction of low count data. Higher contrast results were

Maximum Principles for Discrete and Semidiscrete Reaction-Diffusion Equation

Directory of Open Access Journals (Sweden)

Petr Stehlík

2015-01-01

Full Text Available We study reaction-diffusion equations with a general reaction function f on one-dimensional lattices with continuous or discrete time ux′  (or  Δtux=k(ux-1-2ux+ux+1+f(ux, x∈Z. We prove weak and strong maximum and minimum principles for corresponding initial-boundary value problems. Whereas the maximum principles in the semidiscrete case (continuous time exhibit similar features to those of fully continuous reaction-diffusion model, in the discrete case the weak maximum principle holds for a smaller class of functions and the strong maximum principle is valid in a weaker sense. We describe in detail how the validity of maximum principles depends on the nonlinearity and the time step. We illustrate our results on the Nagumo equation with the bistable nonlinearity.

Minimal length, Friedmann equations and maximum density

Energy Technology Data Exchange (ETDEWEB)

Awad, Adel [Center for Theoretical Physics, British University of Egypt,Sherouk City 11837, P.O. Box 43 (Egypt); Department of Physics, Faculty of Science, Ain Shams University,Cairo, 11566 (Egypt); Ali, Ahmed Farag [Centre for Fundamental Physics, Zewail City of Science and Technology,Sheikh Zayed, 12588, Giza (Egypt); Department of Physics, Faculty of Science, Benha University,Benha, 13518 (Egypt)

2014-06-16

Inspired by Jacobson’s thermodynamic approach, Cai et al. have shown the emergence of Friedmann equations from the first law of thermodynamics. We extend Akbar-Cai derivation http://dx.doi.org/10.1103/PhysRevD.75.084003 of Friedmann equations to accommodate a general entropy-area law. Studying the resulted Friedmann equations using a specific entropy-area law, which is motivated by the generalized uncertainty principle (GUP), reveals the existence of a maximum energy density closed to Planck density. Allowing for a general continuous pressure p(ρ,a) leads to bounded curvature invariants and a general nonsingular evolution. In this case, the maximum energy density is reached in a finite time and there is no cosmological evolution beyond this point which leaves the big bang singularity inaccessible from a spacetime prospective. The existence of maximum energy density and a general nonsingular evolution is independent of the equation of state and the spacial curvature k. As an example we study the evolution of the equation of state p=ωρ through its phase-space diagram to show the existence of a maximum energy which is reachable in a finite time.

Maximum-Entropy Inference with a Programmable Annealer

Science.gov (United States)

Chancellor, Nicholas; Szoke, Szilard; Vinci, Walter; Aeppli, Gabriel; Warburton, Paul A.

2016-03-01

Optimisation problems typically involve finding the ground state (i.e. the minimum energy configuration) of a cost function with respect to many variables. If the variables are corrupted by noise then this maximises the likelihood that the solution is correct. The maximum entropy solution on the other hand takes the form of a Boltzmann distribution over the ground and excited states of the cost function to correct for noise. Here we use a programmable annealer for the information decoding problem which we simulate as a random Ising model in a field. We show experimentally that finite temperature maximum entropy decoding can give slightly better bit-error-rates than the maximum likelihood approach, confirming that useful information can be extracted from the excited states of the annealer. Furthermore we introduce a bit-by-bit analytical method which is agnostic to the specific application and use it to show that the annealer samples from a highly Boltzmann-like distribution. Machines of this kind are therefore candidates for use in a variety of machine learning applications which exploit maximum entropy inference, including language processing and image recognition.

Probabilistic maximum-value wind prediction for offshore environments

DEFF Research Database (Denmark)

Staid, Andrea; Pinson, Pierre; Guikema, Seth D.

2015-01-01

statistical models to predict the full distribution of the maximum-value wind speeds in a 3 h interval. We take a detailed look at the performance of linear models, generalized additive models and multivariate adaptive regression splines models using meteorological covariates such as gust speed, wind speed......, convective available potential energy, Charnock, mean sea-level pressure and temperature, as given by the European Center for Medium-Range Weather Forecasts forecasts. The models are trained to predict the mean value of maximum wind speed, and the residuals from training the models are used to develop...... the full probabilistic distribution of maximum wind speed. Knowledge of the maximum wind speed for an offshore location within a given period can inform decision-making regarding turbine operations, planned maintenance operations and power grid scheduling in order to improve safety and reliability...

Teacher learning and student outcomes in the context of classroom discourse. Findings from a video-based teacher professional development programme

Directory of Open Access Journals (Sweden)

Katharina Kiemer

2014-06-01

Full Text Available We present an innovative teacher professional development programme (TPD focusing on the re-definition of teachers’ discourse behaviour. We report findings on teacher learning and student outcomes, and reflect on practical implications and directions for future research on the programme. In the “Dialogic Video Cycle” (DVC six teachers participated in a year-long intervention built on effective components of TPD and using videos of teachers’ own practices as tools for reflection and basis for group discussions. We compared the DVC with a traditional TPD programme (n= 4 teachers. Additionally, students (N= 226 were assessed regarding their motivational orientations and individual beliefs. Results show that effective TPD components could successfully be implemented in the DVC and that this new and innovative programme enhances teachers’ performance in classroom discourse and affects students’ interest in the subject, self-efficacy and domain-specific self-concept of ability positively. Thus, the DVC seems a promising tool to foster teacher learning with an impact on perceived student motivation and learning. Presentiamo un programma innovativo per lo sviluppo professionale degli insegnanti (TPD, centrato sulla ridefinizione della conduzione di interazioni verbali in classe. Sono riportati i risultati dell’apprendimento di insegnanti e studenti, e la riflessione sulle implicazioni pratiche per la ricerca futura sul programma. Nel “Dialogic Video Cycle” (DVC sei insegnanti hanno partecipato per un anno a un intervento di TPD mediante videoregistrazioni usate come strumenti di riflessione sulle proprie pratiche e per le discussioni di gruppo. Abbiamo confrontato il DVC con un programma TPD tradizionale (n= 4 insegnanti. Inoltre sono stati valutati gli orientamenti degli studenti (N= 226 in termini di motivazione e fiducia nelle proprie capacità. I risultati mostrano che le componenti efficaci del TPD potrebbero essere attuate con

Characterizing graphs of maximum matching width at most 2

DEFF Research Database (Denmark)

Jeong, Jisu; Ok, Seongmin; Suh, Geewon

2017-01-01

The maximum matching width is a width-parameter that is de ned on a branch-decomposition over the vertex set of a graph. The size of a maximum matching in the bipartite graph is used as a cut-function. In this paper, we characterize the graphs of maximum matching width at most 2 using the minor o...

The Maximum Resource Bin Packing Problem

DEFF Research Database (Denmark)

Boyar, J.; Epstein, L.; Favrholdt, L.M.

2006-01-01

Usually, for bin packing problems, we try to minimize the number of bins used or in the case of the dual bin packing problem, maximize the number or total size of accepted items. This paper presents results for the opposite problems, where we would like to maximize the number of bins used...... algorithms, First-Fit-Increasing and First-Fit-Decreasing for the maximum resource variant of classical bin packing. For the on-line variant, we define maximum resource variants of classical and dual bin packing. For dual bin packing, no on-line algorithm is competitive. For classical bin packing, we find...

Maximum entropy analysis of EGRET data

DEFF Research Database (Denmark)

Pohl, M.; Strong, A.W.

1997-01-01

EGRET data are usually analysed on the basis of the Maximum-Likelihood method \\cite{ma96} in a search for point sources in excess to a model for the background radiation (e.g. \\cite{hu97}). This method depends strongly on the quality of the background model, and thus may have high systematic unce...... uncertainties in region of strong and uncertain background like the Galactic Center region. Here we show images of such regions obtained by the quantified Maximum-Entropy method. We also discuss a possible further use of MEM in the analysis of problematic regions of the sky....

Density estimation by maximum quantum entropy

International Nuclear Information System (INIS)

Silver, R.N.; Wallstrom, T.; Martz, H.F.

1993-01-01

A new Bayesian method for non-parametric density estimation is proposed, based on a mathematical analogy to quantum statistical physics. The mathematical procedure is related to maximum entropy methods for inverse problems and image reconstruction. The information divergence enforces global smoothing toward default models, convexity, positivity, extensivity and normalization. The novel feature is the replacement of classical entropy by quantum entropy, so that local smoothing is enforced by constraints on differential operators. The linear response of the estimate is proportional to the covariance. The hyperparameters are estimated by type-II maximum likelihood (evidence). The method is demonstrated on textbook data sets

All-solution processed composite hole transport layer for quantum dot light emitting diode

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaoli [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, School of Science, Tianjin University, Tianjin 300072 (China); Synergetic Innovation Center of Chemical Science and Engineering, Tianjin (China); Dai, Haitao, E-mail: htdai@tju.edu.cn [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, School of Science, Tianjin University, Tianjin 300072 (China); Zhao, Junliang; Wang, Shuguo [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, School of Science, Tianjin University, Tianjin 300072 (China); Sun, Xiaowei [Department of Electrical & Electronic Engineering, South University of Science and Technology of China, Tangchang Road 1088, Shenzhen, Guangdong 518055 (China)

2016-03-31

In the present work, poly-TPD and TCTA composite hole transport layer (HTL) was employed in solution processed CdSe/ZnS quantum dot light emitting diodes (QLEDs). As the doping level of TCTA can determine the carriers transport efficiency of HTL, the proper mixing ratio of TCTA and poly-TPD should be found to optimize the performance of composite HTL for QLEDs. The doping of poly-TPD by low TCTA content can make its HOMO level lower and then reduce the energy barrier height from HTL to quantum dots (QDs), whereas the doping of poly-TPD by the concentrated TCTA results in the degraded performance of QLEDs due to its decreased hole transport mobility. By using the optimized composition with poly-TPD:TCTA (3:1) as the hole transport layer, the luminescence of the device exhibits about double enhancement compared with that of poly-TPD based device. The improvement of luminescence is mainly attributed to the lower energy barrier of hole injection. The Förster resonant energy transfer (FRET) mechanism in the devices was investigated through theoretical and experimental analysis and the results indicate that the TCTA doping makes no difference on FRET. Therefore, the charge injection mechanism dominates the improved performance of the devices. - Highlights: • Quantum dot light emitting diodes (QLEDs) were fabricated by all solution method. • The performance of QLEDs was optimized by varying the composite hole transport layer. • The blend HTL could promote hole injection by optimizing HOMO levels. • The energy transfer mechanism was analyzed by studying Förster resonant energy transfer process.

Analogue of Pontryagin's maximum principle for multiple integrals minimization problems

OpenAIRE

Mikhail, Zelikin

2016-01-01

The theorem like Pontryagin's maximum principle for multiple integrals is proved. Unlike the usual maximum principle, the maximum should be taken not over all matrices, but only on matrices of rank one. Examples are given.

Microprocessor Controlled Maximum Power Point Tracker for Photovoltaic Application

International Nuclear Information System (INIS)

Jiya, J. D.; Tahirou, G.

2002-01-01

This paper presents a microprocessor controlled maximum power point tracker for photovoltaic module. Input current and voltage are measured and multiplied within the microprocessor, which contains an algorithm to seek the maximum power point. The duly cycle of the DC-DC converter, at which the maximum power occurs is obtained, noted and adjusted. The microprocessor constantly seeks for improvement of obtained power by varying the duty cycle

Maximum entropy reconstructions for crystallographic imaging; Cristallographie et reconstruction d`images par maximum d`entropie

Energy Technology Data Exchange (ETDEWEB)

Papoular, R

1997-07-01

The Fourier Transform is of central importance to Crystallography since it allows the visualization in real space of tridimensional scattering densities pertaining to physical systems from diffraction data (powder or single-crystal diffraction, using x-rays, neutrons, electrons or else). In turn, this visualization makes it possible to model and parametrize these systems, the crystal structures of which are eventually refined by Least-Squares techniques (e.g., the Rietveld method in the case of Powder Diffraction). The Maximum Entropy Method (sometimes called MEM or MaxEnt) is a general imaging technique, related to solving ill-conditioned inverse problems. It is ideally suited for tackling undetermined systems of linear questions (for which the number of variables is much larger than the number of equations). It is already being applied successfully in Astronomy, Radioastronomy and Medical Imaging. The advantages of using MAXIMUM Entropy over conventional Fourier and `difference Fourier` syntheses stem from the following facts: MaxEnt takes the experimental error bars into account; MaxEnt incorporate Prior Knowledge (e.g., the positivity of the scattering density in some instances); MaxEnt allows density reconstructions from incompletely phased data, as well as from overlapping Bragg reflections; MaxEnt substantially reduces truncation errors to which conventional experimental Fourier reconstructions are usually prone. The principles of Maximum Entropy imaging as applied to Crystallography are first presented. The method is then illustrated by a detailed example specific to Neutron Diffraction: the search for proton in solids. (author). 17 refs.

Involvement of Ethylene in the Latex Metabolism and Tapping Panel Dryness of Hevea brasiliensis

Science.gov (United States)

Putranto, Riza-Arief; Herlinawati, Eva; Rio, Maryannick; Leclercq, Julie; Piyatrakul, Piyanuch; Gohet, Eric; Sanier, Christine; Oktavia, Fetrina; Pirrello, Julien; Kuswanhadi; Montoro, Pascal

2015-01-01

Ethephon, an ethylene releaser, is used to stimulate latex production in Hevea brasiliensis. Ethylene induces many functions in latex cells including the production of reactive oxygen species (ROS). The accumulation of ROS is responsible for the coagulation of rubber particles in latex cells, resulting in the partial or complete stoppage of latex flow. This study set out to assess biochemical and histological changes as well as changes in gene expression in latex and phloem tissues from trees grown under various harvesting systems. The Tapping Panel Dryness (TPD) susceptibility of Hevea clones was found to be related to some biochemical parameters, such as low sucrose and high inorganic phosphorus contents. A high tapping frequency and ethephon stimulation induced early TPD occurrence in a high latex metabolism clone and late occurrence in a low latex metabolism clone. TPD-affected trees had smaller number of laticifer vessels compared to healthy trees, suggesting a modification of cambial activity. The differential transcript abundance was observed for twenty-seven candidate genes related to TPD occurrence in latex and phloem tissues for ROS-scavenging, ethylene biosynthesis and signalling genes. The predicted function for some Ethylene Response Factor genes suggested that these candidate genes should play an important role in regulating susceptibility to TPD. PMID:26247941

Comprehensive performance analyses and optimization of the irreversible thermodynamic cycle engines (TCE) under maximum power (MP) and maximum power density (MPD) conditions

International Nuclear Information System (INIS)

Gonca, Guven; Sahin, Bahri; Ust, Yasin; Parlak, Adnan

2015-01-01

This paper presents comprehensive performance analyses and comparisons for air-standard irreversible thermodynamic cycle engines (TCE) based on the power output, power density, thermal efficiency, maximum dimensionless power output (MP), maximum dimensionless power density (MPD) and maximum thermal efficiency (MEF) criteria. Internal irreversibility of the cycles occurred during the irreversible-adiabatic processes is considered by using isentropic efficiencies of compression and expansion processes. The performances of the cycles are obtained by using engine design parameters such as isentropic temperature ratio of the compression process, pressure ratio, stroke ratio, cut-off ratio, Miller cycle ratio, exhaust temperature ratio, cycle temperature ratio and cycle pressure ratio. The effects of engine design parameters on the maximum and optimal performances are investigated. - Highlights: • Performance analyses are conducted for irreversible thermodynamic cycle engines. • Comprehensive computations are performed. • Maximum and optimum performances of the engines are shown. • The effects of design parameters on performance and power density are examined. • The results obtained may be guidelines to the engine designers

Shower maximum detector for SDC calorimetry

International Nuclear Information System (INIS)

Ernwein, J.

1994-01-01

A prototype for the SDC end-cap (EM) calorimeter complete with a pre-shower and a shower maximum detector was tested in beams of electrons and Π's at CERN by an SDC subsystem group. The prototype was manufactured from scintillator tiles and strips read out with 1 mm diameter wave-length shifting fibers. The design and construction of the shower maximum detector is described, and results of laboratory tests on light yield and performance of the scintillator-fiber system are given. Preliminary results on energy and position measurements with the shower max detector in the test beam are shown. (authors). 4 refs., 5 figs

Maximum Power Point Tracking in Variable Speed Wind Turbine Based on Permanent Magnet Synchronous Generator Using Maximum Torque Sliding Mode Control Strategy

Institute of Scientific and Technical Information of China (English)

Esmaeil Ghaderi; Hossein Tohidi; Behnam Khosrozadeh

2017-01-01

The present study was carried out in order to track the maximum power point in a variable speed turbine by minimizing electromechanical torque changes using a sliding mode control strategy.In this strategy,fhst,the rotor speed is set at an optimal point for different wind speeds.As a result of which,the tip speed ratio reaches an optimal point,mechanical power coefficient is maximized,and wind turbine produces its maximum power and mechanical torque.Then,the maximum mechanical torque is tracked using electromechanical torque.In this technique,tracking error integral of maximum mechanical torque,the error,and the derivative of error are used as state variables.During changes in wind speed,sliding mode control is designed to absorb the maximum energy from the wind and minimize the response time of maximum power point tracking (MPPT).In this method,the actual control input signal is formed from a second order integral operation of the original sliding mode control input signal.The result of the second order integral in this model includes control signal integrity,full chattering attenuation,and prevention from large fluctuations in the power generator output.The simulation results,calculated by using MATLAB/m-file software,have shown the effectiveness of the proposed control strategy for wind energy systems based on the permanent magnet synchronous generator (PMSG).

32 CFR 842.35 - Depreciation and maximum allowances.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Depreciation and maximum allowances. 842.35... LITIGATION ADMINISTRATIVE CLAIMS Personnel Claims (31 U.S.C. 3701, 3721) § 842.35 Depreciation and maximum allowances. The military services have jointly established the “Allowance List-Depreciation Guide” to...

Electroluminescence and negative differential resistance studies of ...

Indian Academy of Sciences (India)

(a) Molecular structure of Alq3, TPD and PBD and (b) single-layer OLED structure fabricated in this ... lowed by deionized water, acetone and isopropanol. The cleaned ... at a higher voltage for the TPD:PDB:Alq3 (4.5 V) as com- pared to that of ...

Characterization of porosity via secondary reactions. Final technical report, 1 September 1991--30 November 1995

Energy Technology Data Exchange (ETDEWEB)

Calo, J.M.; Zhang, L.; Hall, P.J.; Antxustegi, M. [Brown Univ., Providence, RI (United States). Div. of Engineering

1997-09-01

A new approach to the study of porosity and porosity development in coal chars during gasification was investigated. This approach involves the establishment of the relationships between the amount and type of surface complexes evolved during post-activation temperature programmed desorption (TPD), and the porosity, as measured by gas adsorption and small angle neutron scattering (SANS) techniques. With this new method, the total surface area and micropore volume can be determined by the interpretation of post-activation TPD spectra. The primary conclusion of this work is that it is possible to predict total surface area and micropore volume from TPD spectra. From the extended random pore model, additional information about the micropore surface area, the nonmicroporous surface area, and the mean micropore size development as a function of reaction time (or burn-off) can also be predicted. Therefore, combining the TPD technique and the extended random pore model provides a new method for the characterization of char porosity.

UNA DEFENSA DE LA PERSPECTIVA FORMATIVA DEL DESARROLLO PROFESIONAL DOCENTE EN LA PRÁCTICA EDUCATIVA DE LOS PROFESORES DE QUÍMICA

Directory of Open Access Journals (Sweden)

Ricardo Aponte-Buitrago

Full Text Available Teachers’ Professional Development (TPD has been defined as learning opportunities, insights and discussions that improves the personal, social and pedagogical growing of the teachers, whose main goal is the enhancement of their knowledge about teaching strategies and research skills around educational practice. The above topics are needed to change the learning and teaching forms in chemical education; however, the tie between TPD and the classroom practice of the chemistry teachers still has not been greatly discussed in the literature. Thus, this paper seeks to generate a perspective upon theoretical issues related with TPD and their relevance in the chemistry teaching, where the teacher as researcher is put forward as a promoter of classroom research projects, which he joins chemical, pedagogical and practical knowledge for the improvement of learning process of his students. Moreover, the fruitful relationship between TPD and teaching of chemistry educators with the aim to make teachers’ communities around their professional development is analyzed.

40 CFR 141.63 - Maximum contaminant levels (MCLs) for microbiological contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels (MCLs) for microbiological contaminants. 141.63 Section 141.63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Water Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.63 Maximum...

Particle Swarm Optimization Based of the Maximum Photovoltaic ...

African Journals Online (AJOL)

Photovoltaic electricity is seen as an important source of renewable energy. The photovoltaic array is an unstable source of power since the peak power point depends on the temperature and the irradiation level. A maximum peak power point tracking is then necessary for maximum efficiency. In this work, a Particle Swarm ...

40 CFR 1045.140 - What is my engine's maximum engine power?

Science.gov (United States)

2010-07-01

...) Maximum engine power for an engine family is generally the weighted average value of maximum engine power... engine family's maximum engine power apply in the following circumstances: (1) For outboard or personal... value for maximum engine power from all the different configurations within the engine family to...

42 CFR 409.62 - Lifetime maximum on inpatient psychiatric care.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Lifetime maximum on inpatient psychiatric care. 409....62 Lifetime maximum on inpatient psychiatric care. There is a lifetime maximum of 190 days on inpatient psychiatric hospital services available to any beneficiary. Therefore, once an individual receives...

Maximum-entropy description of animal movement.

Science.gov (United States)

Fleming, Chris H; Subaşı, Yiğit; Calabrese, Justin M

2015-03-01

We introduce a class of maximum-entropy states that naturally includes within it all of the major continuous-time stochastic processes that have been applied to animal movement, including Brownian motion, Ornstein-Uhlenbeck motion, integrated Ornstein-Uhlenbeck motion, a recently discovered hybrid of the previous models, and a new model that describes central-place foraging. We are also able to predict a further hierarchy of new models that will emerge as data quality improves to better resolve the underlying continuity of animal movement. Finally, we also show that Langevin equations must obey a fluctuation-dissipation theorem to generate processes that fall from this class of maximum-entropy distributions when the constraints are purely kinematic.

Interaction of D2 with H2O amorphous ice studied by temperature-programmed desorption experiments.

Science.gov (United States)

Amiaud, L; Fillion, J H; Baouche, S; Dulieu, F; Momeni, A; Lemaire, J L

2006-03-07

The gas-surface interaction of molecular hydrogen D2 with a thin film of porous amorphous solid water (ASW) grown at 10 K by slow vapor deposition has been studied by temperature-programmed-desorption (TPD) experiments. Molecular hydrogen diffuses rapidly into the porous network of the ice. The D2 desorption occurring between 10 and 30 K is considered here as a good probe of the effective surface of ASW interacting with the gas. The desorption kinetics have been systematically measured at various coverages. A careful analysis based on the Arrhenius plot method has provided the D2 binding energies as a function of the coverage. Asymmetric and broad distributions of binding energies were found, with a maximum population peaking at low energy. We propose a model for the desorption kinetics that assumes a complete thermal equilibrium of the molecules with the ice film. The sample is characterized by a distribution of adsorption sites that are filled according to a Fermi-Dirac statistic law. The TPD curves can be simulated and fitted to provide the parameters describing the distribution of the molecules as a function of their binding energy. This approach contributes to a correct description of the interaction of molecular hydrogen with the surface of possibly porous grain mantles in the interstellar medium.

Solution-processed white organic light-emitting devices based on small-molecule materials

International Nuclear Information System (INIS)

Wang Dongdong; Wu Zhaoxin; Zhang Xinwen; Wang Dawei; Hou Xun

2010-01-01

We investigated solution-processed films of 4,4'-bis(2,2-diphenylvinyl)-1,1'-bibenyl (DPVBi) and its blends with N,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD) by atomic force microscopy (AFM). The AFM result shows that the solution-processed films are pin-free and their morphology is smooth enough to be used in OLEDs. We have developed a solution-processed white organic light-emitting device (WOLEDs) based on small-molecules, in which the light-emitting layer (EML) was formed by spin-coating the solution of small-molecules on top of the solution-processed hole-transporting layer. This WOLEDs, in which the EML consists of co-host (DPVBi and TPD), the blue dopant (4,4'-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl) and the yellow dye (5,6,11,12-tetraphenylnaphtacene), has a current efficiency of 6.0 cd/A at a practical luminance of 1000 cd/m 2 , a maximum luminance of 22500 cd/m 2 , and its color coordinates are quite stable. Our research shows a possible approach to achieve efficient and low-cost small-molecule-based WOLEDs, which avoids the complexities of the co-evaporation process of multiple dopants and host materials in vacuum depositions.

Production of biodiesel from palm oil using modified Malaysian natural dolomites

International Nuclear Information System (INIS)

Shajaratun Nur, Z.A.; Taufiq-Yap, Y.H.; Rabiah Nizah, M.F.; Teo, Siow Hwa; Syazwani, O.N.; Islam, Aminul

2014-01-01

Highlights: • Transesterification was carried out using modified Malaysian natural dolomite catalyst. • Characterizations of the catalyst were performed by using XRD, TPD-CO 2 , BET and SEM. • Maximum biodiesel conversion of 100% was achieved from SnO 2 /dolomite catalyst. • The yield was affected by the surface are as well as the basicity of catalyst. • The transesterification reaction gave significant conversion with relatively lower amount of catalyst. - Abstract: Calcined dolomite (AD), produced by calcination of Malaysian dolomite (UD) promotes a potential natural catalyst for biodiesel production from palm oil with the conversion of 99.98%. The catalysts were characterized by using X-ray Diffractometer (XRD), Brunauer–Emmet–Teller (BET) surface area, Scanning Electron Microscopy (SEM) and Temperature Programmed Desorption (TPD) of CO 2 . All catalysts were then employed for transesterification reaction under different conditions (time, methanol to oil molar ratio and amount of catalyst). SnO 2 doped on activated dolomite (SD) shows an optimum conversion (99.98%) at conditions, i.e. 15:1 methanol to oil molar ratio in 4 h compared to ZnO doped on activated dolomite (ZD) and AD. The catalytic activities of these catalysts were found to be depending on the basicity as well as the surface area of the catalyst used

Extreme Maximum Land Surface Temperatures.

Science.gov (United States)

Garratt, J. R.

1992-09-01

There are numerous reports in the literature of observations of land surface temperatures. Some of these, almost all made in situ, reveal maximum values in the 50°-70°C range, with a few, made in desert regions, near 80°C. Consideration of a simplified form of the surface energy balance equation, utilizing likely upper values of absorbed shortwave flux (1000 W m2) and screen air temperature (55°C), that surface temperatures in the vicinity of 90°-100°C may occur for dry, darkish soils of low thermal conductivity (0.1-0.2 W m1 K1). Numerical simulations confirm this and suggest that temperature gradients in the first few centimeters of soil may reach 0.5°-1°C mm1 under these extreme conditions. The study bears upon the intrinsic interest of identifying extreme maximum temperatures and yields interesting information regarding the comfort zone of animals (including man).

On Maximum Entropy and Inference

Directory of Open Access Journals (Sweden)

Luigi Gresele

2017-11-01

Full Text Available Maximum entropy is a powerful concept that entails a sharp separation between relevant and irrelevant variables. It is typically invoked in inference, once an assumption is made on what the relevant variables are, in order to estimate a model from data, that affords predictions on all other (dependent variables. Conversely, maximum entropy can be invoked to retrieve the relevant variables (sufficient statistics directly from the data, once a model is identified by Bayesian model selection. We explore this approach in the case of spin models with interactions of arbitrary order, and we discuss how relevant interactions can be inferred. In this perspective, the dimensionality of the inference problem is not set by the number of parameters in the model, but by the frequency distribution of the data. We illustrate the method showing its ability to recover the correct model in a few prototype cases and discuss its application on a real dataset.

Fractal Dimension and Maximum Sunspot Number in Solar Cycle

Directory of Open Access Journals (Sweden)

R.-S. Kim

2006-09-01

Full Text Available The fractal dimension is a quantitative parameter describing the characteristics of irregular time series. In this study, we use this parameter to analyze the irregular aspects of solar activity and to predict the maximum sunspot number in the following solar cycle by examining time series of the sunspot number. For this, we considered the daily sunspot number since 1850 from SIDC (Solar Influences Data analysis Center and then estimated cycle variation of the fractal dimension by using Higuchi's method. We examined the relationship between this fractal dimension and the maximum monthly sunspot number in each solar cycle. As a result, we found that there is a strong inverse relationship between the fractal dimension and the maximum monthly sunspot number. By using this relation we predicted the maximum sunspot number in the solar cycle from the fractal dimension of the sunspot numbers during the solar activity increasing phase. The successful prediction is proven by a good correlation (r=0.89 between the observed and predicted maximum sunspot numbers in the solar cycles.

Automatic maximum entropy spectral reconstruction in NMR

International Nuclear Information System (INIS)

Mobli, Mehdi; Maciejewski, Mark W.; Gryk, Michael R.; Hoch, Jeffrey C.

2007-01-01

Developments in superconducting magnets, cryogenic probes, isotope labeling strategies, and sophisticated pulse sequences together have enabled the application, in principle, of high-resolution NMR spectroscopy to biomolecular systems approaching 1 megadalton. In practice, however, conventional approaches to NMR that utilize the fast Fourier transform, which require data collected at uniform time intervals, result in prohibitively lengthy data collection times in order to achieve the full resolution afforded by high field magnets. A variety of approaches that involve nonuniform sampling have been proposed, each utilizing a non-Fourier method of spectrum analysis. A very general non-Fourier method that is capable of utilizing data collected using any of the proposed nonuniform sampling strategies is maximum entropy reconstruction. A limiting factor in the adoption of maximum entropy reconstruction in NMR has been the need to specify non-intuitive parameters. Here we describe a fully automated system for maximum entropy reconstruction that requires no user-specified parameters. A web-accessible script generator provides the user interface to the system

Stationary neutrino radiation transport by maximum entropy closure

International Nuclear Information System (INIS)

Bludman, S.A.

1994-11-01

The authors obtain the angular distributions that maximize the entropy functional for Maxwell-Boltzmann (classical), Bose-Einstein, and Fermi-Dirac radiation. In the low and high occupancy limits, the maximum entropy closure is bounded by previously known variable Eddington factors that depend only on the flux. For intermediate occupancy, the maximum entropy closure depends on both the occupation density and the flux. The Fermi-Dirac maximum entropy variable Eddington factor shows a scale invariance, which leads to a simple, exact analytic closure for fermions. This two-dimensional variable Eddington factor gives results that agree well with exact (Monte Carlo) neutrino transport calculations out of a collapse residue during early phases of hydrostatic neutron star formation

Maximum power per VA control of vector controlled interior ...

Indian Academy of Sciences (India)

Thakur Sumeet Singh

2018-04-11

Apr 11, 2018 ... Department of Electrical Engineering, Indian Institute of Technology Delhi, New ... The MPVA operation allows maximum-utilization of the drive-system. ... Permanent magnet motor; unity power factor; maximum VA utilization; ...

Application of maximum entropy to neutron tunneling spectroscopy

International Nuclear Information System (INIS)

Mukhopadhyay, R.; Silver, R.N.

1990-01-01

We demonstrate the maximum entropy method for the deconvolution of high resolution tunneling data acquired with a quasielastic spectrometer. Given a precise characterization of the instrument resolution function, a maximum entropy analysis of lutidine data obtained with the IRIS spectrometer at ISIS results in an effective factor of three improvement in resolution. 7 refs., 4 figs

The maximum economic depth of groundwater abstraction for irrigation

Science.gov (United States)

Bierkens, M. F.; Van Beek, L. P.; de Graaf, I. E. M.; Gleeson, T. P.

2017-12-01

Over recent decades, groundwater has become increasingly important for agriculture. Irrigation accounts for 40% of the global food production and its importance is expected to grow further in the near future. Already, about 70% of the globally abstracted water is used for irrigation, and nearly half of that is pumped groundwater. In many irrigated areas where groundwater is the primary source of irrigation water, groundwater abstraction is larger than recharge and we see massive groundwater head decline in these areas. An important question then is: to what maximum depth can groundwater be pumped for it to be still economically recoverable? The objective of this study is therefore to create a global map of the maximum depth of economically recoverable groundwater when used for irrigation. The maximum economic depth is the maximum depth at which revenues are still larger than pumping costs or the maximum depth at which initial investments become too large compared to yearly revenues. To this end we set up a simple economic model where costs of well drilling and the energy costs of pumping, which are a function of well depth and static head depth respectively, are compared with the revenues obtained for the irrigated crops. Parameters for the cost sub-model are obtained from several US-based studies and applied to other countries based on GDP/capita as an index of labour costs. The revenue sub-model is based on gross irrigation water demand calculated with a global hydrological and water resources model, areal coverage of crop types from MIRCA2000 and FAO-based statistics on crop yield and market price. We applied our method to irrigated areas in the world overlying productive aquifers. Estimated maximum economic depths range between 50 and 500 m. Most important factors explaining the maximum economic depth are the dominant crop type in the area and whether or not initial investments in well infrastructure are limiting. In subsequent research, our estimates of

What controls the maximum magnitude of injection-induced earthquakes?

Science.gov (United States)

Eaton, D. W. S.

2017-12-01

Three different approaches for estimation of maximum magnitude are considered here, along with their implications for managing risk. The first approach is based on a deterministic limit for seismic moment proposed by McGarr (1976), which was originally designed for application to mining-induced seismicity. This approach has since been reformulated for earthquakes induced by fluid injection (McGarr, 2014). In essence, this method assumes that the upper limit for seismic moment release is constrained by the pressure-induced stress change. A deterministic limit is given by the product of shear modulus and the net injected fluid volume. This method is based on the assumptions that the medium is fully saturated and in a state of incipient failure. An alternative geometrical approach was proposed by Shapiro et al. (2011), who postulated that the rupture area for an induced earthquake falls entirely within the stimulated volume. This assumption reduces the maximum-magnitude problem to one of estimating the largest potential slip surface area within a given stimulated volume. Finally, van der Elst et al. (2016) proposed that the maximum observed magnitude, statistically speaking, is the expected maximum value for a finite sample drawn from an unbounded Gutenberg-Richter distribution. These three models imply different approaches for risk management. The deterministic method proposed by McGarr (2014) implies that a ceiling on the maximum magnitude can be imposed by limiting the net injected volume, whereas the approach developed by Shapiro et al. (2011) implies that the time-dependent maximum magnitude is governed by the spatial size of the microseismic event cloud. Finally, the sample-size hypothesis of Van der Elst et al. (2016) implies that the best available estimate of the maximum magnitude is based upon observed seismicity rate. The latter two approaches suggest that real-time monitoring is essential for effective management of risk. A reliable estimate of maximum

Topics in Bayesian statistics and maximum entropy

International Nuclear Information System (INIS)

Mutihac, R.; Cicuttin, A.; Cerdeira, A.; Stanciulescu, C.

1998-12-01

Notions of Bayesian decision theory and maximum entropy methods are reviewed with particular emphasis on probabilistic inference and Bayesian modeling. The axiomatic approach is considered as the best justification of Bayesian analysis and maximum entropy principle applied in natural sciences. Particular emphasis is put on solving the inverse problem in digital image restoration and Bayesian modeling of neural networks. Further topics addressed briefly include language modeling, neutron scattering, multiuser detection and channel equalization in digital communications, genetic information, and Bayesian court decision-making. (author)

Maximum vehicle cabin temperatures under different meteorological conditions

Science.gov (United States)

Grundstein, Andrew; Meentemeyer, Vernon; Dowd, John

2009-05-01

A variety of studies have documented the dangerously high temperatures that may occur within the passenger compartment (cabin) of cars under clear sky conditions, even at relatively low ambient air temperatures. Our study, however, is the first to examine cabin temperatures under variable weather conditions. It uses a unique maximum vehicle cabin temperature dataset in conjunction with directly comparable ambient air temperature, solar radiation, and cloud cover data collected from April through August 2007 in Athens, GA. Maximum cabin temperatures, ranging from 41-76°C, varied considerably depending on the weather conditions and the time of year. Clear days had the highest cabin temperatures, with average values of 68°C in the summer and 61°C in the spring. Cloudy days in both the spring and summer were on average approximately 10°C cooler. Our findings indicate that even on cloudy days with lower ambient air temperatures, vehicle cabin temperatures may reach deadly levels. Additionally, two predictive models of maximum daily vehicle cabin temperatures were developed using commonly available meteorological data. One model uses maximum ambient air temperature and average daily solar radiation while the other uses cloud cover percentage as a surrogate for solar radiation. From these models, two maximum vehicle cabin temperature indices were developed to assess the level of danger. The models and indices may be useful for forecasting hazardous conditions, promoting public awareness, and to estimate past cabin temperatures for use in forensic analyses.

Combining Experiments and Simulations Using the Maximum Entropy Principle

DEFF Research Database (Denmark)

Boomsma, Wouter; Ferkinghoff-Borg, Jesper; Lindorff-Larsen, Kresten

2014-01-01

are not in quantitative agreement with experimental data. The principle of maximum entropy is a general procedure for constructing probability distributions in the light of new data, making it a natural tool in cases when an initial model provides results that are at odds with experiments. The number of maximum entropy...... in the context of a simple example, after which we proceed with a real-world application in the field of molecular simulations, where the maximum entropy procedure has recently provided new insight. Given the limited accuracy of force fields, macromolecular simulations sometimes produce results....... Three very recent papers have explored this problem using the maximum entropy approach, providing both new theoretical and practical insights to the problem. We highlight each of these contributions in turn and conclude with a discussion on remaining challenges....

Optimization of the Laser Properties of Polymer Films Doped with N,N´-Bis(3-methylphenyl-N,N´-diphenylbenzidine

Directory of Open Access Journals (Sweden)

María A. Díaz-García

2009-09-01

Full Text Available This review compiles the work performed in the field of organic solid-state lasers with the hole-transporting organic molecule N,N´-bis(3-methylphenyl-N,N´-diphenylbenzidine system (TPD, in view of improving active laser material properties. The optimization of the amplified spontaneous emission characteristics, i.e., threshold, linewidth, emission wavelength and photostability, of polystyrene films doped with TPD in waveguide configuration has been achieved by investigating the influence of several materials parameters such as film thickness and TPD concentration. In addition, the influence in the emission properties of the inclusion of a second-order distributed feedback grating in the substrate is discussed.

Exciplex or electroplex emissions from the interface between aromatic diamine and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline?

Science.gov (United States)

Zhu, Haina; Xu, Zheng; Zhang, Fujun; Zhao, Suling; Song, Dandan

2008-06-01

Organic light-emitting diodes (OLEDs) have been fabricated which consist of N, N'-diphenyl- N, N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine) (TPD), 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP), and tris(8-hydroxyquinoline) aluminum (Alq 3). Four emission peaks located at about 401 nm, 425 nm, 452 nm and 480 nm have been obtained in the electroluminescence (EL) spectra of these devices. The former two emissions originate from the exciton emission of TPD molecular. The last two emissions could be attributed to local (LOC) exiplex emission and charge transfer (CT) exiplex emission at the interface between TPD and BCP layers, respectively.

Bibliometric Profile of Turkish Journal of Psychology Türk Psikoloji Dergisi'nin Bibliyometrik Profili

Directory of Open Access Journals (Sweden)

Umut Al

2007-06-01

at the bottom of psychology journals which indexed by the Social Science Citation Index. Türk Psikoloji Dergisi (TPD 1995 yılından beri Social Science Citation Index tarafından dizinlenmektedir. Bu çalışmada Türk Psikoloji Dergisi (TPD ve Türk Psikoloji Dergisi 'ndeki makaleler bibliyometrik özellikleri açısından ele alınmaktadır. Çalışmamızda 1995-2005 yılları arasında yayımlanan 118 makale incelenmektedir. Araştırmamızda yanıt aranmakta olan sorular şunlardır: 1 TPD 'de yayımlanan makaleler psikolojinin hangi alt alanlarında yoğunlaşmaktadır? 2 TPD'nin çok yazarlık durumu nedir? 3 TPD'de yayımlanan makalelerin yazarları hangi kurumlarda çalışmaktadır? 4 TPD 'de yayımlanan yazıların atıf alanlarının özellikleri nelerdir? 5 TPD 'de yayımlanan makalelerde en sık atıf yapılan kaynak türü (dergi, kitap vb. hangisidir? 6 TPD 'de en sık atıf yapılan dergiler hangileridir? 7 TPD'de yayımlanan makalelerde dergilere yapılan atıfların dağılımı Bradford Yasasına uymakta mıdır? 8 TPD'deki makalelerin atıfları ile JCR'deki etki faktörü arasında bir ilişki bulunmakta mıdır? 9 Psikoloji literatürünün yaşlanma hızı nedir? 10 Etki faktörü açısından TPD'nin JCR'deki psikoloji dergileri arasındaki konumu nedir? Yayımlanan makalelerin neredeyse tamamı Türkçe'dir. Dergide makale yayımlayan kişilerin bağlı bulundukları kurumlara göre yapılan değerlendirmede en çok katkının Hacettepe, Ankara ve Orta Doğu Teknik Üniversitelerindeki araştırmacılar tarafından gerçekleştirildiği görülmektedir. TPD 'de yayımlanan makalelerin %57'sine (67 makale atıf dizinleri kapsamında yayımlanan makaleler tarafından hiç atıf yapılmamıştır. TPD 'de 1995-2005 yılları arasında yayımlanan makalelere toplam 135 atıf yapılmıştır. Bu atıfların %34'ü yazarların kendi makalelerine yapmış olduğu atıflardır. Ayrıca TPD'ye yapılan atıfların %41'i yine TPD'de yay

Maximum entropy beam diagnostic tomography

International Nuclear Information System (INIS)

Mottershead, C.T.

1985-01-01

This paper reviews the formalism of maximum entropy beam diagnostic tomography as applied to the Fusion Materials Irradiation Test (FMIT) prototype accelerator. The same formalism has also been used with streak camera data to produce an ultrahigh speed movie of the beam profile of the Experimental Test Accelerator (ETA) at Livermore

Teacher Learning in Technology Professional Development and Its Impact on Student Achievement in Science

Science.gov (United States)

Lee, Hyunju; Longhurst, Max; Campbell, Todd

2017-01-01

This research investigated teacher learning and teacher beliefs in a two-year technology professional development (TPD) for teachers and its impact on their student achievement in science in the western part of the United States. Middle-school science teachers participated in TPD focused on information communication technologies (ICTs) and their…

Professionel udvikling af naturfagslærere

DEFF Research Database (Denmark)

Krogh, Lars Brian

2016-01-01

& Hollingsworth, 2002) som model for tænkning omkring TPD, samt anvende en mange-lags evalueringsoptik i overensstemmelse med Guskey (2002). Den eksisterende viden om, hvad der skal til for at professionelle udviklingsaktiviteter får virkning opsummeres som afsæt for en drøftelse af TPD-design. Endelig...

A Maximum Radius for Habitable Planets.

Science.gov (United States)

Alibert, Yann

2015-09-01

We compute the maximum radius a planet can have in order to fulfill two constraints that are likely necessary conditions for habitability: 1- surface temperature and pressure compatible with the existence of liquid water, and 2- no ice layer at the bottom of a putative global ocean, that would prevent the operation of the geologic carbon cycle to operate. We demonstrate that, above a given radius, these two constraints cannot be met: in the Super-Earth mass range (1-12 Mearth), the overall maximum that a planet can have varies between 1.8 and 2.3 Rearth. This radius is reduced when considering planets with higher Fe/Si ratios, and taking into account irradiation effects on the structure of the gas envelope.

On semidefinite programming relaxations of maximum k-section

NARCIS (Netherlands)

de Klerk, E.; Pasechnik, D.V.; Sotirov, R.; Dobre, C.

2012-01-01

We derive a new semidefinite programming bound for the maximum k -section problem. For k=2 (i.e. for maximum bisection), the new bound is at least as strong as a well-known bound by Poljak and Rendl (SIAM J Optim 5(3):467–487, 1995). For k ≥ 3the new bound dominates a bound of Karisch and Rendl

Modeling multisite streamflow dependence with maximum entropy copula

Science.gov (United States)

Hao, Z.; Singh, V. P.

2013-10-01

Synthetic streamflows at different sites in a river basin are needed for planning, operation, and management of water resources projects. Modeling the temporal and spatial dependence structure of monthly streamflow at different sites is generally required. In this study, the maximum entropy copula method is proposed for multisite monthly streamflow simulation, in which the temporal and spatial dependence structure is imposed as constraints to derive the maximum entropy copula. The monthly streamflows at different sites are then generated by sampling from the conditional distribution. A case study for the generation of monthly streamflow at three sites in the Colorado River basin illustrates the application of the proposed method. Simulated streamflow from the maximum entropy copula is in satisfactory agreement with observed streamflow.

Teacher learning in technology professional development and its impact on student achievement in science

Science.gov (United States)

Lee, Hyunju; Longhurst, Max; Campbell, Todd

2017-07-01

This research investigated teacher learning and teacher beliefs in a two-year technology professional development (TPD) for teachers and its impact on their student achievement in science in the western part of the United States. Middle-school science teachers participated in TPD focused on information communication technologies (ICTs) and their applications in science inquiry pedagogy. Three self-reporting teacher instruments were used alongside their student achievement scores on the end-of-year state-science-test. The teacher self-reporting measures investigated technological literacy, ICT capabilities, and pedagogical beliefs about science inquiry pedagogy. Data were collected every year, and descriptive statistics, t-tests, and Pearson's correlations were used for analysis. We found teachers' technological skills and ICT capabilities increasing over time with significant gains each year. Additionally, teachers' pedagogical beliefs changed to become more science inquiry oriented over time; however, the gains were not significant until after the second year of TPD. Comparisons of teacher learning and belief measures with student achievement revealed that the students' performance was correlated to teachers' pedagogical beliefs about science inquiry, but not to their technological skills nor to their ICT capabilities. This research suggests that pedagogical considerations should be foregrounded in TPD and that this may require more longitudinal TPD to ensure that technology integration in science instruction is consequential to student learning.

Maximum stellar iron core mass

Indian Academy of Sciences (India)

60, No. 3. — journal of. March 2003 physics pp. 415–422. Maximum stellar iron core mass. F W GIACOBBE. Chicago Research Center/American Air Liquide ... iron core compression due to the weight of non-ferrous matter overlying the iron cores within large .... thermal equilibrium velocities will tend to be non-relativistic.

The regulation of starch accumulation in Panicum maximum Jacq ...

African Journals Online (AJOL)

... decrease the starch level. These observations are discussed in relation to the photosynthetic characteristics of P. maximum. Keywords: accumulation; botany; carbon assimilation; co2 fixation; growth conditions; mesophyll; metabolites; nitrogen; nitrogen levels; nitrogen supply; panicum maximum; plant physiology; starch; ...

Atomic-Scale View on the H₂O Formation Reaction from H₂ on O-Rich RuO₂(110)

DEFF Research Database (Denmark)

Wei, Yinying; Martinez, Umberto; Lammich, Lutz

2014-01-01

The H2O formation reaction from H-2 on O-rich RuO2(110) was studied by temperature-programmed desorption and reaction (TPD/TPR) and scanning tunneling microscopy (STM) measurements and density functional theory (DFT) calculations. On the one hand, following H-2 adsorption at 270 K, our TPD/TPR me...

Dabrowski's Theory of Positive Disintegration and Giftedness: Overexcitability Research Findings

Science.gov (United States)

Mendaglio, Sal; Tillier, William

2006-01-01

During the past 20 years, a significant body of literature has emerged focusing on the application of Dabrowski's theory of positive disintegration (TPD) to the study of gifted individuals. Although much of this literature is prescriptive, some research reports spanning this time period are available. A perusal of research on TPD's applicability…

75 FR 10420 - Approval and Promulgation of Implementation Plans: 1-Hour Ozone Extreme Area Plan for San Joaquin...

Science.gov (United States)

2010-03-08

... Air Pollution Control District's Rule 9310, ``School Bus Fleets.'' DATES: Effective Date: This rule is... Pollution Control District (SJVAPCD or the District) in 2004 and amended in 2005. The 2004 SIP addresses CAA... day (tpd) and nitrogen oxides (NO X ) by 20 tpd and to approve SJVAPCD's Rule 9310, School Bus Fleets...

Maximum entropy beam diagnostic tomography

International Nuclear Information System (INIS)

Mottershead, C.T.

1985-01-01

This paper reviews the formalism of maximum entropy beam diagnostic tomography as applied to the Fusion Materials Irradiation Test (FMIT) prototype accelerator. The same formalism has also been used with streak camera data to produce an ultrahigh speed movie of the beam profile of the Experimental Test Accelerator (ETA) at Livermore. 11 refs., 4 figs

A portable storage maximum thermometer

International Nuclear Information System (INIS)

Fayart, Gerard.

1976-01-01

A clinical thermometer storing the voltage corresponding to the maximum temperature in an analog memory is described. End of the measurement is shown by a lamp switch out. The measurement time is shortened by means of a low thermal inertia platinum probe. This portable thermometer is fitted with cell test and calibration system [fr

A Maximum Resonant Set of Polyomino Graphs

Directory of Open Access Journals (Sweden)

Zhang Heping

2016-05-01

Full Text Available A polyomino graph P is a connected finite subgraph of the infinite plane grid such that each finite face is surrounded by a regular square of side length one and each edge belongs to at least one square. A dimer covering of P corresponds to a perfect matching. Different dimer coverings can interact via an alternating cycle (or square with respect to them. A set of disjoint squares of P is a resonant set if P has a perfect matching M so that each one of those squares is M-alternating. In this paper, we show that if K is a maximum resonant set of P, then P − K has a unique perfect matching. We further prove that the maximum forcing number of a polyomino graph is equal to the cardinality of a maximum resonant set. This confirms a conjecture of Xu et al. [26]. We also show that if K is a maximal alternating set of P, then P − K has a unique perfect matching.

Spatio-temporal observations of the tertiary ozone maximum

Directory of Open Access Journals (Sweden)

V. F. Sofieva

2009-07-01

Full Text Available We present spatio-temporal distributions of the tertiary ozone maximum (TOM, based on GOMOS (Global Ozone Monitoring by Occultation of Stars ozone measurements in 2002–2006. The tertiary ozone maximum is typically observed in the high-latitude winter mesosphere at an altitude of ~72 km. Although the explanation for this phenomenon has been found recently – low concentrations of odd-hydrogen cause the subsequent decrease in odd-oxygen losses – models have had significant deviations from existing observations until recently. Good coverage of polar night regions by GOMOS data has allowed for the first time to obtain spatial and temporal observational distributions of night-time ozone mixing ratio in the mesosphere.

The distributions obtained from GOMOS data have specific features, which are variable from year to year. In particular, due to a long lifetime of ozone in polar night conditions, the downward transport of polar air by the meridional circulation is clearly observed in the tertiary ozone maximum time series. Although the maximum tertiary ozone mixing ratio is achieved close to the polar night terminator (as predicted by the theory, TOM can be observed also at very high latitudes, not only in the beginning and at the end, but also in the middle of winter. We have compared the observational spatio-temporal distributions of the tertiary ozone maximum with that obtained using WACCM (Whole Atmosphere Community Climate Model and found that the specific features are reproduced satisfactorily by the model.

Since ozone in the mesosphere is very sensitive to HO_x concentrations, energetic particle precipitation can significantly modify the shape of the ozone profiles. In particular, GOMOS observations have shown that the tertiary ozone maximum was temporarily destroyed during the January 2005 and December 2006 solar proton events as a result of the HO_x enhancement from the increased ionization.

Direct maximum parsimony phylogeny reconstruction from genotype data

OpenAIRE

Sridhar, Srinath; Lam, Fumei; Blelloch, Guy E; Ravi, R; Schwartz, Russell

2007-01-01

Abstract Background Maximum parsimony phylogenetic tree reconstruction from genetic variation data is a fundamental problem in computational genetics with many practical applications in population genetics, whole genome analysis, and the search for genetic predictors of disease. Efficient methods are available for reconstruction of maximum parsimony trees from haplotype data, but such data are difficult to determine directly for autosomal DNA. Data more commonly is available in the form of ge...

Comparison of Protein Value of Commercial Baby Food with Homemade Baby Food and Casein Standard in Rats as the Refference point

Directory of Open Access Journals (Sweden)

Z. Asemi

2008-10-01

Full Text Available Background and ObjectivesEvaluation of protein quality in food is of great importance due to the biological and economical impacts of food proteins. This study has been conducted with the aim of comparing the protein quality of homemade food (mixture of macaroni and soy bean with commercial baby food (Cerelac Wheat using Casein as the refference point.MethodsThis study was conducted on 64 twenty one day old male Wistar rats. The rats were divided into 8 groups, and each group was put on a different diet regiments. The diet regiments were as follow: 2 homemade food+Cerelac test diet, 1 Ccasein+Methionine standard diet, 1 protien-free basal diet, 2 test diet, 1 standard diet and 1 basal diet. The purpose of protien-free diet was to evaluate True Protien Digestability (TPD. Net Protein Ratio (NPR and Protien Efficiency Ratios (PER were investigated by the basal diet. Protein intake and increasing of weight were determined for NPR and PER calculating. Nitrogen intake and fecal Nitrogen were determined to calculate TPD. Comparison of TPD, NPR and PER among the groups were analyzed by ANOVA and Tukey methods.ResultsTPD values of Standard, Cerelac and homemade food diets were 92.8±4, 87±8 and 85.4±3.2; NPR values were 4.3±0.4, 4.3±0.9, 3.8±0.6; and PER values were 3±0.2, 2.5±0.4, 1.7±0.1 respectively. The statistical difference between TPD and PER values were significant (p 0.05. ConclusionThese results shows that TPD and PER of homemade foods are lower than Cerelac while their NPR are acceptable.Keywords: Protein; Cerelac; Macaroni; Soybeens.

Mediating Artifact in Teacher Professional Development

Science.gov (United States)

Svendsen, Bodil

2015-01-01

This article focuses on teacher professional development (TPD) in natural science through the 5E model as mediating artifact. The study was conducted in an upper secondary school, grounded in a school-based intervention research project. My contribution to the field of research on TPD is founded on the hypothesis that teachers would be best…

Fungic microflora of Panicum maximum and Styosanthes spp. commercial seed / Microflora fúngica de sementes comerciais de Panicum maximum e Stylosanthes spp.

Directory of Open Access Journals (Sweden)

Larissa Rodrigues Fabris

2010-09-01

Full Text Available The sanitary quality of 26 lots commercial seeds of tropical forages, produced in different regions (2004-05 and 2005-06 was analyzed. The lots were composed of seeds of Panicum maximum ('Massai', 'Mombaça' e 'Tanzânia' and stylo ('Estilosantes Campo Grande' - ECG. Additionally, seeds of two lots of P. maximum for exportation were analyzed. The blotter test was used, at 20ºC under alternating light and darkness in a 12 h photoperiod, for seven days. The Aspergillus, Cladosporium and Rhizopus genus consisted the secondary or saprophytes fungi (FSS with greatest frequency in P. maximum lots. In general, there was low incidence of these fungus in the seeds. In relation to pathogenic fungi (FP, it was detected high frequency of contaminated lots by Bipolaris, Curvularia, Fusarium and Phoma genus. Generally, there was high incidence of FP in P. maximum seeds. The occurrence of Phoma sp. was hight, because in 81% of the lots showed incidence superior to 50%. In 'ECG' seeds it was detected FSS (Aspergillus, Cladosporium, and Penicillium genus and FP (Bipolaris, Curvularia, Fusarium and Phoma genus, usually, in low incidence. FSS and FP were associated to P. maximum seeds for exportation, with significant incidence in some cases. The results indicated that there was a limiting factor in all producer regions regarding sanitary quality of the seeds.Sementes comerciais de forrageiras tropicais, pertencente a 26 lotes produzidos em diferentes regiões (safras 2004-05 e 2005-06, foram avaliadas quanto à sanidade. Foram analisadas sementes de cultivares de Panicum maximum (Massai, Mombaça e Tanzânia e de estilosantes (Estilosantes Campo Grande – ECG. Adicionalmente, avaliou-se a qualidade sanitária de dois lotes de sementes de P. maximum destinados à exportação. Para isso, as sementes foram submetidas ao teste de papel de filtro em gerbox, os quais foram incubados a 20ºC, com fotoperíodo de 12 h, durante sete dias. Os fungos saprófitos ou

EUREST PLUS - European Regulatory Science on Tobacco: Policy implementation to reduce lung diseases - Proposal (Horizon2020

Directory of Open Access Journals (Sweden)

Constantine Vardavas

2016-03-01

Full Text Available EUREST-PLUS, a thirteen –partner EU joint proposal, coordinated by ENSP (Coordinator: Constantine Vardavas, aims to monitor and evaluate the impact of the TPD at an EU level. The specific objectives of the proposal are: 1. To evaluate the psychosocial and behavioural impact of TPD implementation and FCTC implementation, through the creation of a longitudinal cohort of adult smokers in 6 EU MS (Germany, Greece, Hungary, Poland, Romania, Spain in a pre- vs. post- study design. 2. To assess support for TPD implementation through secondary dataset analyses of the 2015 Special Eurobarometer on Tobacco Survey (SETS, and through trend analyses on the merged datasets of the 2009, 2012 and2015 SETS datasets. 3. To document changes in e-cigarette product parameters (technical design, labelling, packaging and chemical composition following implementation of Article 20 of the TPD. 4. To enhance innovative joint research collaborations, through the pooling and comparisons across both other EU countries of the International Tobacco Control (ITC Project, and other non-EU countries.

Kinetics of aerobically activated sludge on terylene artificial silk printing and dyeing wastewater treatment.

Science.gov (United States)

Guan, Bao-hong; Wu, Zhong-biao; Xu, Gen-liang

2004-04-01

Aerobically activated sludge processing was carried out to treat terylene artificial silk printing and dyeing wastewater (TPD wastewater) in a lab-scale experiment, focusing on the kinetics of the COD removal. The kinetics parameters determined from experiment were applied to evaluate the biological treatability of wastewater. Experiments showed that COD removal could be divided into two stages, in which the ratio BOD/COD (B/C) was the key factor for stage division. At the rapid-removal stage with B/C>0.1, COD removal could be described by a zero order reaction. At the moderate-removal stage with B/Ckinetic parameters, the biological treatability of TPD wastewater was superior to that of traditional textile wastewater. But COD removal from TPD-wastewater was much more difficult than that from domestic and industrial wastewater, such as papermaking, beer, phenol wastewater, etc. The expected effluent quality strongly related to un-biodegradable COD and kinetics rather than total COD. The results provide useful basis for further scaling up and efficient operation of TPD wastewater treatment.

Measurement of Laser Plasma Instability (LPI) Driven Light Scattering from Plasmas Produced by Nike KrF Laser

Science.gov (United States)

Oh, Jaechul; Weaver, J. L.; Phillips, L.; Obenschain, S. P.; Schmitt, A. J.; Kehne, D. M.; Serlin, V.; Lehmberg, R. H.; McLean, E. A.; Manka, C. K.

2010-11-01

With short wavelength (248 nm), large bandwidth (1˜3 THz), and ISI beam smoothing, Nike KrF laser provides unique research opportunities and potential for direct-drive inertial confinement fusion. Previous Nike experiments observed two plasmon decay (TPD) driven signals from CH plasmas at the laser intensities above ˜2x10^15 W/cm^2 with total laser energies up to 1 kJ of ˜350 ps FWHM pulses. We have performed a further experiment with longer laser pulses (0.5˜4.0 ns FWHM) and will present combined results of the experiments focusing on light emission data in spectral ranges relevant to the Raman (SRS) and TPD instabilities. Time- or space-resolved spectral features of TPD were detected at different viewing angles and the absolute intensity calibrated spectra of thermal background were used to obtain blackbody temperatures in the plasma corona. The wave vector distribution in k-space of the participating TPD plasmons will be also discussed. These results show promise for the proposed direct-drive designs.

A Study of the Impact of Transformative Professional Development on Hispanic Student Performance on State Mandated Assessments of Science in Elementary School

Science.gov (United States)

Johnson, Carla C.; Fargo, Jamison D.

2014-11-01

This paper reports the findings of a study of the impact of the transformative professional development (TPD) model on student achievement on state-mandated assessments of science in elementary school. Two schools (one intervention and one control) participated in the case study where teachers from one school received the TPD intervention across a 2-year period while teachers at the other school received no program and continued business as usual. The TPD program includes a focus on the core conceptual framework for effective professional development (Desimone in Educ Res 38:181-199, 2009) as well as an emphasis on culturally relevant pedagogy (CRP) and other effective science instructional strategies. Findings revealed that participation in TPD had a significant impact on student achievement for Burns Elementary with the percentage of proficient students growing from 25 % at baseline to 67 % at the end of the 2-year program, while the comparison school did not experience similar growth. Implications for future research and implementation of professional development programs to meet the needs of teachers in the realm of CRP in science are discussed.

Effect of inserting of thin Rubrene layer on performance of Organic Light-Emitting Diodes based on Zn(BTz)2

Science.gov (United States)

Tomova, R. L.; Petrova, P. K.; Stoycheva-Topalova, R. T.

2010-11-01

Organic light-emitting diodes (OLEDs) with improved performances are fabricated using a thin (1 nm) yellow-emitting layer of 5,6,11,12-tetraphenylnaphthacene (Rubrene) inserted at different position in green emitting electroluminescent (EL) layer of bis-(2-(2-hydroxyphenyl) benzothiazole)zinc (Zn(BTz)2) in configuration: ITO/PVK:TPD/ Zn(BTz)2 (x nm)/ Rubrene (1 nm)/ Zn(BTz)2 (75-x nm)/Al, where PVK:TPD is a hole transporting layer of N, N'-bis(3-methylphenyl)-N, N'-diphenylbenzidine (TPD) incorporated in poly(N-vinylcarbazole) (PVK) matrix and Al is a cathode. EL spectra predominantly influenced by Rubrene emission when the doping layer is close to (PVK:TPD)/ Zn(BTz)2 (x→ 0-15 nm) and to Zn(BTz)2/Al (x→ 70-75 nm) interfaces and shift toward emission of Zn(BTz)2 increasing the distance of Rubrene from both interfaces (x→35 nm). The same dependence of the EL efficiency on the position of the doping Rubrene layer in the OLED structure was found.

Temperature Programmed Desorption of Quench-condensed Krypton and Acetone in Air; Selective Concentration of Ultra-trace Gas Components.

Science.gov (United States)

Suzuki, Taku T; Sakaguchi, Isao

2016-01-01

Selective concentration of ultra-trace components in air-like gases has an important application in analyzing volatile organic compounds in the gas. In the present study, we examined quench-condensation of the sample gas on a ZnO substrate below 50 K followed by temperature programmed desorption (TPD) (low temperature TPD) as a selective gas concentration technique. We studied two specific gases in the normal air; krypton as an inert gas and acetone as a reactive gas. We evaluated the relationship between the operating condition of low temperature TPD and the lowest detection limit. In the case of krypton, we observed the selective concentration by exposing at 6 K followed by thermal desorption at about 60 K. On the other hand, no selectivity appeared for acetone although trace acetone was successfully concentrated. This is likely due to the solvent effect by a major component in the air, which is suggested to be water. We suggest that pre-condensation to remove the water component may improve the selectivity in the trace acetone analysis by low temperature TPD.

Effect of inserting of thin Rubrene layer on performance of Organic Light-Emitting Diodes based on Zn(BTz){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Tomova, R L; Petrova, P K; Stoycheva-Topalova, R T, E-mail: reni@clf.bas.b [Institute of optical materials and technologies ' Acad. J. Malinowski' , Bulgarian Academy of Sciences, ' Acad. G. Bonchev' str. bl. 109, 1113 Sofia (Bulgaria)

2010-11-01

Organic light-emitting diodes (OLEDs) with improved performances are fabricated using a thin (1 nm) yellow-emitting layer of 5,6,11,12-tetraphenylnaphthacene (Rubrene) inserted at different position in green emitting electroluminescent (EL) layer of bis-(2-(2-hydroxyphenyl) benzothiazole)zinc (Zn(BTz){sub 2}) in configuration: ITO/PVK:TPD/ Zn(BTz){sub 2} (x nm)/ Rubrene (1 nm)/ Zn(BTz){sub 2} (75-x nm)/Al, where PVK:TPD is a hole transporting layer of N, N'-bis(3-methylphenyl)-N, N'-diphenylbenzidine (TPD) incorporated in poly(N-vinylcarbazole) (PVK) matrix and Al is a cathode. EL spectra predominantly influenced by Rubrene emission when the doping layer is close to (PVK:TPD)/ Zn(BTz){sub 2} (x{yields} 0-15 nm) and to Zn(BTz){sub 2}/Al (x{yields} 70-75 nm) interfaces and shift toward emission of Zn(BTz){sub 2} increasing the distance of Rubrene from both interfaces (x{yields}35 nm). The same dependence of the EL efficiency on the position of the doping Rubrene layer in the OLED structure was found.

The molecular, electronic structures and vibrational spectra of metal-free, N,N'-dideuterio and magnesium tetra-2,3-pyridino-porphyrazines: Density functional calculations.

Science.gov (United States)

Liu, Zhongqiang; Zhang, Xianxi; Zhang, Yuexing; Li, Renjie; Jiang, Jianzhuang

2006-10-01

A theoretical investigation of the fully optimized geometries and electronic structures of the metal-free (TPdPzH(2)), N,N'-dideuterio (TPdPzD(2)), and magnesium (TPdPzMg) tetra-2,3-pyridino-porphyrazine has been conducted based on density functional theory. The optimized geometries at density functional theory level for these compounds are reported here for the first time. A comparison between the different molecules for the geometry, molecular orbital, and atomic charge is made. The substituent effect of the N atoms on the molecular structures of these compounds is discussed. The IR and Raman spectra for these three compounds have also been calculated at density functional B3LYP level using the 6-31G(d) basis set. Detailed assignments of the NH, NM, and pyridine ring vibrational bands in the IR and Raman spectra have been made based on assistance of animated pictures. The simulated IR spectra of TPdPzH(2) are compared with the experimental absorption spectra, and very good consistency has been found. The isotope effect on the IR and Raman spectra is also discussed.

78 FR 49370 - Inflation Adjustment of Maximum Forfeiture Penalties

Science.gov (United States)

2013-08-14

... ``civil monetary penalties provided by law'' at least once every four years. DATES: Effective September 13... increases the maximum civil monetary forfeiture penalties available to the Commission under its rules... maximum civil penalties established in that section to account for inflation since the last adjustment to...

5 CFR 838.711 - Maximum former spouse survivor annuity.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Maximum former spouse survivor annuity... Orders Awarding Former Spouse Survivor Annuities Limitations on Survivor Annuities § 838.711 Maximum former spouse survivor annuity. (a) Under CSRS, payments under a court order may not exceed the amount...

A tropospheric ozone maximum over the equatorial Southern Indian Ocean

Directory of Open Access Journals (Sweden)

L. Zhang

2012-05-01

Full Text Available We examine the distribution of tropical tropospheric ozone (O₃ from the Microwave Limb Sounder (MLS and the Tropospheric Emission Spectrometer (TES by using a global three-dimensional model of tropospheric chemistry (GEOS-Chem. MLS and TES observations of tropospheric O₃ during 2005 to 2009 reveal a distinct, persistent O₃ maximum, both in mixing ratio and tropospheric column, in May over the Equatorial Southern Indian Ocean (ESIO. The maximum is most pronounced in 2006 and 2008 and less evident in the other three years. This feature is also consistent with the total column O₃ observations from the Ozone Mapping Instrument (OMI and the Atmospheric Infrared Sounder (AIRS. Model results reproduce the observed May O₃ maximum and the associated interannual variability. The origin of the maximum reflects a complex interplay of chemical and dynamic factors. The O₃ maximum is dominated by the O₃ production driven by lightning nitrogen oxides (NO_x emissions, which accounts for 62% of the tropospheric column O₃ in May 2006. We find the contribution from biomass burning, soil, anthropogenic and biogenic sources to the O₃ maximum are rather small. The O₃ productions in the lightning outflow from Central Africa and South America both peak in May and are directly responsible for the O₃ maximum over the western ESIO. The lightning outflow from Equatorial Asia dominates over the eastern ESIO. The interannual variability of the O₃ maximum is driven largely by the anomalous anti-cyclones over the southern Indian Ocean in May 2006 and 2008. The lightning outflow from Central Africa and South America is effectively entrained by the anti-cyclones followed by northward transport to the ESIO.

Solar maximum observatory

International Nuclear Information System (INIS)

Rust, D.M.

1984-01-01

The successful retrieval and repair of the Solar Maximum Mission (SMM) satellite by Shuttle astronauts in April 1984 permitted continuance of solar flare observations that began in 1980. The SMM carries a soft X ray polychromator, gamma ray, UV and hard X ray imaging spectrometers, a coronagraph/polarimeter and particle counters. The data gathered thus far indicated that electrical potentials of 25 MeV develop in flares within 2 sec of onset. X ray data show that flares are composed of compressed magnetic loops that have come too close together. Other data have been taken on mass ejection, impacts of electron beams and conduction fronts with the chromosphere and changes in the solar radiant flux due to sunspots. 13 references

Post optimization paradigm in maximum 3-satisfiability logic programming

Science.gov (United States)

Mansor, Mohd. Asyraf; Sathasivam, Saratha; Kasihmuddin, Mohd Shareduwan Mohd

2017-08-01

Maximum 3-Satisfiability (MAX-3SAT) is a counterpart of the Boolean satisfiability problem that can be treated as a constraint optimization problem. It deals with a conundrum of searching the maximum number of satisfied clauses in a particular 3-SAT formula. This paper presents the implementation of enhanced Hopfield network in hastening the Maximum 3-Satisfiability (MAX-3SAT) logic programming. Four post optimization techniques are investigated, including the Elliot symmetric activation function, Gaussian activation function, Wavelet activation function and Hyperbolic tangent activation function. The performances of these post optimization techniques in accelerating MAX-3SAT logic programming will be discussed in terms of the ratio of maximum satisfied clauses, Hamming distance and the computation time. Dev-C++ was used as the platform for training, testing and validating our proposed techniques. The results depict the Hyperbolic tangent activation function and Elliot symmetric activation function can be used in doing MAX-3SAT logic programming.

Mass mortality of the vermetid gastropod Ceraesignum maximum

Science.gov (United States)

Brown, A. L.; Frazer, T. K.; Shima, J. S.; Osenberg, C. W.

2016-09-01

Ceraesignum maximum (G.B. Sowerby I, 1825), formerly Dendropoma maximum, was subject to a sudden, massive die-off in the Society Islands, French Polynesia, in 2015. On Mo'orea, where we have detailed documentation of the die-off, these gastropods were previously found in densities up to 165 m-2. In July 2015, we surveyed shallow back reefs of Mo'orea before, during and after the die-off, documenting their swift decline. All censused populations incurred 100% mortality. Additional surveys and observations from Mo'orea, Tahiti, Bora Bora, and Huahine (but not Taha'a) suggested a similar, and approximately simultaneous, die-off. The cause(s) of this cataclysmic mass mortality are currently unknown. Given the previously documented negative effects of C. maximum on corals, we expect the die-off will have cascading effects on the reef community.

Preconditioning Strategies for Solving Elliptic Difference Equations on a Multiprocessor.

Science.gov (United States)

1982-01-01

CALLING MA31C. C TD - TIME REQUIRED BY MA31C TO PERFORM THE C FACTORIZATION. 160 C TDT - TOTAL TIME REQUIRED BY SUBROUTINE FACTOR. C TDT-T IM3-T IMI...TPD-TIM2-TIM1 TD -TIM3-TIM2 165 C WRITE(LP,70) TDT,TPD, TD 70 FORMAT(7H TDT - ,F6.3,7H TPD " F6.3,6H TD ,F6.3) C WRITE(LP, 85) NTYPE,NVERN 170 85 FORMAT...INTEGER INI(IAI) ,INJ(IAJ) ,IK(NN,4) INTEGER NU(3000) C COMMON/EA 4BD /PRVT(4),IPRVT(6) 15 COMMON/MA31I/DD,LP,MP COMMON/MA31J/LROW,LCOL,NCP,ND, IPD

Multi-dimensional PIC-simulations of parametric instabilities for shock-ignition conditions

Directory of Open Access Journals (Sweden)

Riconda C.

2013-11-01

Full Text Available Laser-plasma interaction is investigated for conditions relevant for the shock-ignition (SI scheme of inertial confinement fusion using two-dimensional particle-in-cell (PIC simulations of an intense laser beam propagating in a hot, large-scale, non-uniform plasma. The temporal evolution and interdependence of Raman- (SRS, and Brillouin- (SBS, side/backscattering as well as Two-Plasmon-Decay (TPD are studied. TPD is developing in concomitance with SRS creating a broad spectrum of plasma waves near the quarter-critical density. They are rapidly saturated due to plasma cavitation within a few picoseconds. The hot electron spectrum created by SRS and TPD is relatively soft, limited to energies below one hundred keV.

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile

International Nuclear Information System (INIS)

Chew Siewling; Wang Pengfei; Hong Zirou; Kwong, H.L.; Tang Jianxin; Sun Shiling; Lee, C.S.; Lee, S.-T.

2007-01-01

A new compound with intramolecular charge transfer (ICT) property-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both 'positive' and 'negative' solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N'-diphenyl-N,N'-bis-(3-methylphenyl) (1,1'-diphenyl)4,4'-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m 2 at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m 2 at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m 2 at 4.5 V, a maximum brightness of 12600 cd/m 2 at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile

Energy Technology Data Exchange (ETDEWEB)

Chew Siewling [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Wang Pengfei [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100101 (China)]. E-mail: wangpf@mail.ipc.ac.cn; Hong Zirou [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Kwong, H.L. [Department of Biology and Chemistry, City University of Hong Kong, Hong Kong (China); Tang Jianxin [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Sun Shiling [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, C.S. [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)]. E-mail: apcslee@cityu.edu.hk; Lee, S.-T. [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)]. E-mail: apannale@cityu.edu.hk

2007-06-15

A new compound with intramolecular charge transfer (ICT) property-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both 'positive' and 'negative' solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N'-diphenyl-N,N'-bis-(3-methylphenyl) (1,1'-diphenyl)4,4'-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m{sup 2} at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m{sup 2} at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m{sup 2} at 4.5 V, a maximum brightness of 12600 cd/m{sup 2} at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.

Maximum phytoplankton concentrations in the sea

DEFF Research Database (Denmark)

Jackson, G.A.; Kiørboe, Thomas

2008-01-01

A simplification of plankton dynamics using coagulation theory provides predictions of the maximum algal concentration sustainable in aquatic systems. These predictions have previously been tested successfully against results from iron fertilization experiments. We extend the test to data collect...

On the Pontryagin maximum principle for systems with delays. Economic applications

Science.gov (United States)

Kim, A. V.; Kormyshev, V. M.; Kwon, O. B.; Mukhametshin, E. R.

2017-11-01

The Pontryagin maximum principle [6] is the key stone of finite-dimensional optimal control theory [1, 2, 5]. So beginning with opening the maximum principle it was important to extend the maximum principle on various classes of dynamical systems. In t he paper we consider some aspects of application of i-smooth analysis [3, 4] in the theory of the Pontryagin maximum principle [6] for systems with delays, obtained results can be applied by elaborating optimal program controls in economic models with delays.

Parametric optimization of thermoelectric elements footprint for maximum power generation

DEFF Research Database (Denmark)

Rezania, A.; Rosendahl, Lasse; Yin, Hao

2014-01-01

The development studies in thermoelectric generator (TEG) systems are mostly disconnected to parametric optimization of the module components. In this study, optimum footprint ratio of n- and p-type thermoelectric (TE) elements is explored to achieve maximum power generation, maximum cost......-performance, and variation of efficiency in the uni-couple over a wide range of the heat transfer coefficient on the cold junction. The three-dimensional (3D) governing equations of the thermoelectricity and the heat transfer are solved using the finite element method (FEM) for temperature dependent properties of TE...... materials. The results, which are in good agreement with the previous computational studies, show that the maximum power generation and the maximum cost-performance in the module occur at An/Ap

Coronary ligation reduces maximum sustained swimming speed in Chinook salmon, Oncorhynchus tshawytscha

DEFF Research Database (Denmark)

Farrell, A P; Steffensen, J F

1987-01-01

The maximum aerobic swimming speed of Chinook salmon (Oncorhynchus tshawytscha) was measured before and after ligation of the coronary artery. Coronary artery ligation prevented blood flow to the compact layer of the ventricular myocardium, which represents 30% of the ventricular mass, and produced...... a statistically significant 35.5% reduction in maximum swimming speed. We conclude that the coronary circulation is important for maximum aerobic swimming and implicit in this conclusion is that maximum cardiac performance is probably necessary for maximum aerobic swimming performance....

Design-based online teacher professional development to introduce integration of STEM in Pakistan

Science.gov (United States)

Anwar, Tasneem

In today's global society where innovations spread rapidly, the escalating focus on science, technology, engineering and mathematics (STEM) has quickly intensified in the United States, East Asia and much of Western Europe. Our ever-changing, increasingly global society faces many multidisciplinary problems, and many of the solutions require the integration of multiple science, technology, engineering, and mathematics (STEM) concepts. Thus, there is a critical need to explore the integration of STEM subjects in international education contexts. This dissertation study examined the exploration of integration of STEM in the unique context of Pakistan. This study used three-phase design-based methodological framework derived from McKenney and Reeves (2012) to explore the development of a STEM focused online teacher professional development (oTPD-STEM) and to identify the design features that facilitate teacher learning. The oTPD-STEM program was designed to facilitate eight Pakistani elementary school teachers' exploration of the new idea of STEM integration through both practical and theoretical considerations. This design-based study employed inductive analysis (Strauss and Corbin, 1998) to analyze multiple data sources of interviews, STEM perception responses, reflective learning team conversations, pre-post surveys and artifacts produced in oTPD-STEM. Findings of this study are presented as: (1) design-based decisions for oTPD-STEM, and (2) evolution in understanding of STEM by sharing participant teachers' STEM model for Pakistani context. This study advocates for the potential of school-wide oTPD for interdisciplinary collaboration through support for learner-centered practices.

ITO films realized at room-temperature by ion beam sputtering for high-performance flexible organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lucas, B.; Rammal, W.; Moliton, A. [Limoges Univ., Faculte des Sciences et Techniques, CNRS, UMR 6172, Institut de Recherche XLIM, Dept. MINACOM, 87 - Limoges (France)

2006-06-15

Indium-tin oxide (ITO) thin layers are obtained by an IBS (Ion Beam Sputtering) deposition process. We elaborated ITO films on flexible substrates of polyethylene terephthalate (PET), under soft conditions of low temperatures and fulfilling the requirements of fabrication processes of the organic optoelectronic components. With a non thermally activated (20 Celsius degrees) ITO deposition assisted by an oxygen flow (1 cm{sup 3}/min), we got an optical transmittance of 90% in the visible range, a resistivity around 10{sup -3} {omega}.cm and a surface roughness lower than 1.5 mm. Thus we realized flexible organic light-emitting diodes (FOLEDs) with good performances: a maximum luminance of 12000 cd/m{sup 2} at a voltage of 19 V and a maximum luminous power efficiency around 1 lm/W at a voltage of 10 V (or a maximum current efficiency of 4 cd/A at 14 V) for the (PET(50 {mu}m) / ITO(200 nm) / TPD(40 nm) / Alq3(60 nm) / Ca / Al) structure. (authors)

High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

International Nuclear Information System (INIS)

Wang, Zhaokui; Lou, Yanhui; Naka, Shigeki; Okada, Hiroyuki

2010-01-01

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq 3 ), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m 2 were obtained by optimizing the mixing ratio of PyPySPyPy:Alq 3 :α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m 2 and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.

Effects of bruxism on the maximum bite force

Directory of Open Access Journals (Sweden)

Todić Jelena T.

2017-01-01

Full Text Available Background/Aim. Bruxism is a parafunctional activity of the masticatory system, which is characterized by clenching or grinding of teeth. The purpose of this study was to determine whether the presence of bruxism has impact on maximum bite force, with particular reference to the potential impact of gender on bite force values. Methods. This study included two groups of subjects: without and with bruxism. The presence of bruxism in the subjects was registered using a specific clinical questionnaire on bruxism and physical examination. The subjects from both groups were submitted to the procedure of measuring the maximum bite pressure and occlusal contact area using a single-sheet pressure-sensitive films (Fuji Prescale MS and HS Film. Maximal bite force was obtained by multiplying maximal bite pressure and occlusal contact area values. Results. The average values of maximal bite force were significantly higher in the subjects with bruxism compared to those without bruxism (p 0.01. Maximal bite force was significantly higher in the males compared to the females in all segments of the research. Conclusion. The presence of bruxism influences the increase in the maximum bite force as shown in this study. Gender is a significant determinant of bite force. Registration of maximum bite force can be used in diagnosing and analysing pathophysiological events during bruxism.

Acumulación de hojarasca en un pastizal de Panicum maximum y en un sistema silvopastoril de Panicum maximum y Leucaena leucocephala Litter accumulation in a Panicum maximum grassland and in a silvopastoral system of Panicum maximum and Leucaena leucocephala

Directory of Open Access Journals (Sweden)

Saray Sánchez

2007-09-01

Full Text Available Se realizó un estudio en la Estación Experimental de Pastos y Forrajes "Indio Hatuey", Matanzas, Cuba, con el objetivo de determinar la acumulación de la hojarasca en un pastizal de Panicum maximum Jacq cv. Likoni y en un sistema silvopastoril de Panicum maximum y Leucaena leucocephala (Lam de Wit cv. Cunningham. En los pastizales de P. maximum de ambos sistemas se determinó la acumulación de la hojarasca según la técnica propuesta por Bruce y Ebershon (1982, mientras que la hojarasca de L. leucocephala acumulada en el sistema silvopastoril se determinó según Santa Regina et al. (1997. De forma general, los resultados demostraron que en ambos pastizales la guinea acumuló una menor cantidad de hojarasca durante el período junio-diciembre, etapa en la que se produce su mayor desarrollo vegetativo. En la leucaena la mayor producción de hojarasca ocurrió en el período de diciembre a enero, asociada con la caída natural de sus hojas que se produce por efecto de las temperaturas más bajas y la escasa humedad en el suelo. En el sistema silvopastoril la hojarasca de leucaena representó el mayor porcentaje de peso dentro de la producción total, con un contenido más alto de nitrógeno y de calcio que el de la hojarasca del estrato herbáceo. En la guinea la lluvia fue el factor climático que mayor correlación negativa presentó con la producción de hojarasca en ambos sistemas, y en la leucaena la mayor correlación negativa se encontró con la temperatura mínima.A study was carried out at the Experimental Station of Pastures and Forages "Indio Hatuey", Matanzas, Cuba, with the objective of determining the litter accumulation in a pastureland of Panicum maximum Jacq cv. Likoni and in a silvopastoral system of Panicum maximum and Leucaena leucocephala (Lam de Wit cv. Cunningham. In the P. maximum pasturelands of both systems the litter accumulation was determined by means of the technique proposed by Bruce and Ebershon (1982, while

Parameters determining maximum wind velocity in a tropical cyclone

International Nuclear Information System (INIS)

Choudhury, A.M.

1984-09-01

The spiral structure of a tropical cyclone was earlier explained by a tangential velocity distribution which varies inversely as the distance from the cyclone centre outside the circle of maximum wind speed. The case has been extended in the present paper by adding a radial velocity. It has been found that a suitable combination of radial and tangential velocities can account for the spiral structure of a cyclone. This enables parametrization of the cyclone. Finally a formula has been derived relating maximum velocity in a tropical cyclone with angular momentum, radius of maximum wind speed and the spiral angle. The shapes of the spirals have been computed for various spiral angles. (author)

Exercise-induced maximum metabolic rate scaled to body mass by ...

African Journals Online (AJOL)

Exercise-induced maximum metabolic rate scaled to body mass by the fractal ... rate scaling is that exercise-induced maximum aerobic metabolic rate (MMR) is ... muscle stress limitation, and maximized oxygen delivery and metabolic rates.

Electron density distribution in Si and Ge using multipole, maximum ...

Indian Academy of Sciences (India)

Si and Ge has been studied using multipole, maximum entropy method (MEM) and ... and electron density distribution using the currently available versatile ..... data should be subjected to maximum possible utility for the characterization of.

The maximum-entropy method in superspace

Czech Academy of Sciences Publication Activity Database

van Smaalen, S.; Palatinus, Lukáš; Schneider, M.

2003-01-01

Roč. 59, - (2003), s. 459-469 ISSN 0108-7673 Grant - others:DFG(DE) XX Institutional research plan: CEZ:AV0Z1010914 Keywords : maximum-entropy method, * aperiodic crystals * electron density Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.558, year: 2003

Maximum-entropy clustering algorithm and its global convergence analysis

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

Constructing a batch of differentiable entropy functions touniformly approximate an objective function by means of the maximum-entropy principle, a new clustering algorithm, called maximum-entropy clustering algorithm, is proposed based on optimization theory. This algorithm is a soft generalization of the hard C-means algorithm and possesses global convergence. Its relations with other clustering algorithms are discussed.

maximum neutron flux at thermal nuclear reactors

International Nuclear Information System (INIS)

Strugar, P.

1968-10-01

Since actual research reactors are technically complicated and expensive facilities it is important to achieve savings by appropriate reactor lattice configurations. There is a number of papers, and practical examples of reactors with central reflector, dealing with spatial distribution of fuel elements which would result in higher neutron flux. Common disadvantage of all the solutions is that the choice of best solution is done starting from the anticipated spatial distributions of fuel elements. The weakness of these approaches is lack of defined optimization criteria. Direct approach is defined as follows: determine the spatial distribution of fuel concentration starting from the condition of maximum neutron flux by fulfilling the thermal constraints. Thus the problem of determining the maximum neutron flux is solving a variational problem which is beyond the possibilities of classical variational calculation. This variational problem has been successfully solved by applying the maximum principle of Pontrjagin. Optimum distribution of fuel concentration was obtained in explicit analytical form. Thus, spatial distribution of the neutron flux and critical dimensions of quite complex reactor system are calculated in a relatively simple way. In addition to the fact that the results are innovative this approach is interesting because of the optimization procedure itself [sr

Spin Injection and its Effects on Lasing Action in Conjugated Polymers

Science.gov (United States)

2009-06-16

molecular excited states, namely exciplex states, can have significant response to a low magnetic field. This experimental funding makes it... exciplex states) formed between TPD and BBOT in PMMA matrix. It can be clearly seen that the photoluminescence from inter-molecular exciplex states is...field dependence of photoluminescence (PL) for inter- molecular excited states ( exciplex states). Note, the photoluminescence from pure TPD and

5 CFR 534.203 - Maximum stipends.

Science.gov (United States)

2010-01-01

... maximum stipend established under this section. (e) A trainee at a non-Federal hospital, clinic, or medical or dental laboratory who is assigned to a Federal hospital, clinic, or medical or dental... Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY UNDER OTHER SYSTEMS Student...

Influence of maximum bite force on jaw movement during gummy jelly mastication.

Science.gov (United States)

Kuninori, T; Tomonari, H; Uehara, S; Kitashima, F; Yagi, T; Miyawaki, S

2014-05-01

It is known that maximum bite force has various influences on chewing function; however, there have not been studies in which the relationships between maximum bite force and masticatory jaw movement have been clarified. The aim of this study was to investigate the effect of maximum bite force on masticatory jaw movement in subjects with normal occlusion. Thirty young adults (22 men and 8 women; mean age, 22.6 years) with good occlusion were divided into two groups based on whether they had a relatively high or low maximum bite force according to the median. The maximum bite force was determined according to the Dental Prescale System using pressure-sensitive sheets. Jaw movement during mastication of hard gummy jelly (each 5.5 g) on the preferred chewing side was recorded using a six degrees of freedom jaw movement recording system. The motion of the lower incisal point of the mandible was computed, and the mean values of 10 cycles (cycles 2-11) were calculated. A masticatory performance test was conducted using gummy jelly. Subjects with a lower maximum bite force showed increased maximum lateral amplitude, closing distance, width and closing angle; wider masticatory jaw movement; and significantly lower masticatory performance. However, no differences in the maximum vertical or maximum anteroposterior amplitudes were observed between the groups. Although other factors, such as individual morphology, may influence masticatory jaw movement, our results suggest that subjects with a lower maximum bite force show increased lateral jaw motion during mastication. © 2014 John Wiley & Sons Ltd.

Maximum parsimony on subsets of taxa.

Science.gov (United States)

Fischer, Mareike; Thatte, Bhalchandra D

2009-09-21

In this paper we investigate mathematical questions concerning the reliability (reconstruction accuracy) of Fitch's maximum parsimony algorithm for reconstructing the ancestral state given a phylogenetic tree and a character. In particular, we consider the question whether the maximum parsimony method applied to a subset of taxa can reconstruct the ancestral state of the root more accurately than when applied to all taxa, and we give an example showing that this indeed is possible. A surprising feature of our example is that ignoring a taxon closer to the root improves the reliability of the method. On the other hand, in the case of the two-state symmetric substitution model, we answer affirmatively a conjecture of Li, Steel and Zhang which states that under a molecular clock the probability that the state at a single taxon is a correct guess of the ancestral state is a lower bound on the reconstruction accuracy of Fitch's method applied to all taxa.

Maximum length scale in density based topology optimization

DEFF Research Database (Denmark)

Lazarov, Boyan Stefanov; Wang, Fengwen

2017-01-01

The focus of this work is on two new techniques for imposing maximum length scale in topology optimization. Restrictions on the maximum length scale provide designers with full control over the optimized structure and open possibilities to tailor the optimized design for broader range...... of manufacturing processes by fulfilling the associated technological constraints. One of the proposed methods is based on combination of several filters and builds on top of the classical density filtering which can be viewed as a low pass filter applied to the design parametrization. The main idea...

Maximum Water Hammer Sensitivity Analysis

OpenAIRE

Jalil Emadi; Abbas Solemani

2011-01-01

Pressure waves and Water Hammer occur in a pumping system when valves are closed or opened suddenly or in the case of sudden failure of pumps. Determination of maximum water hammer is considered one of the most important technical and economical items of which engineers and designers of pumping stations and conveyance pipelines should take care. Hammer Software is a recent application used to simulate water hammer. The present study focuses on determining significance of ...

PTree: pattern-based, stochastic search for maximum parsimony phylogenies

OpenAIRE

Gregor, Ivan; Steinbr?ck, Lars; McHardy, Alice C.

2013-01-01

Phylogenetic reconstruction is vital to analyzing the evolutionary relationship of genes within and across populations of different species. Nowadays, with next generation sequencing technologies producing sets comprising thousands of sequences, robust identification of the tree topology, which is optimal according to standard criteria such as maximum parsimony, maximum likelihood or posterior probability, with phylogenetic inference methods is a computationally very demanding task. Here, we ...

Production of biodiesel from non-edible Jatropha curcas oil via transesterification using Bi2O3–La2O3 catalyst

International Nuclear Information System (INIS)

Rabiah Nizah, M.F.; Taufiq-Yap, Y.H.; Rashid, Umer; Teo, Siow Hwa; Shajaratun Nur, Z.A.; Islam, Aminul

2014-01-01

Highlights: • Effects of methanol/oil molar ratio, catalyst amount, reaction temperature and reaction time were optimized. • High FAME conversion of 93% was achieved. • Bi 2 O 3 –La 2 O 3 catalysts were characterized using XRD, BET, TPD-CO 2 and TPD-NH 3 . • Effects of acidity and basicity of the catalyst have been correlated with the FAME conversion. • Bi 2 O 3 –La 2 O 3 catalyst can easy to recover and maintain 87% conversion after three times of successive reuse. - Abstract: The simultaneous esterification and transesterification of Jatropha curcas oil (JCO) was carried out in the presence of Bi 2 O 3 (1–7 wt.%) modified La 2 O 3 catalyst at atmospheric pressure. The catalyst were characterized by X-ray diffraction (XRD), BET surface area, desorption of CO 2 (TPD-CO 2 ) and NH 3 (TPD-NH 3 ). Under the optimal reaction condition of methanol/oil molar ratio of 15:1, 2 wt.% of catalyst amount and a reaction temperature of 150 °C for 4 h, the highest conversion of biodiesel obtained was 93%. This catalyst maintained 87% of FAME conversion after three times of successive reuse

The maximum significant wave height in the Southern North Sea

NARCIS (Netherlands)

Bouws, E.; Tolman, H.L.; Holthuijsen, L.H.; Eldeberky, Y.; Booij, N.; Ferier, P.

1995-01-01

The maximum possible wave conditions along the Dutch coast, which seem to be dominated by the limited water depth, have been estimated in the present study with numerical simulations. Discussions with meteorologists suggest that the maximum possible sustained wind speed in North Sea conditions is

Maximum mass ratio of AM CVn-type binary systems and maximum white dwarf mass in ultra-compact X-ray binaries

Directory of Open Access Journals (Sweden)

Arbutina Bojan

2011-01-01

Full Text Available AM CVn-type stars and ultra-compact X-ray binaries are extremely interesting semi-detached close binary systems in which the Roche lobe filling component is a white dwarf transferring mass to another white dwarf, neutron star or a black hole. Earlier theoretical considerations show that there is a maximum mass ratio of AM CVn-type binary systems (qmax ≈ 2/3 below which the mass transfer is stable. In this paper we derive slightly different value for qmax and more interestingly, by applying the same procedure, we find the maximum expected white dwarf mass in ultra-compact X-ray binaries.

Size dependence of efficiency at maximum power of heat engine

KAUST Repository

Izumida, Y.; Ito, N.

2013-01-01

We perform a molecular dynamics computer simulation of a heat engine model to study how the engine size difference affects its performance. Upon tactically increasing the size of the model anisotropically, we determine that there exists an optimum size at which the model attains the maximum power for the shortest working period. This optimum size locates between the ballistic heat transport region and the diffusive heat transport one. We also study the size dependence of the efficiency at the maximum power. Interestingly, we find that the efficiency at the maximum power around the optimum size attains a value that has been proposed as a universal upper bound, and it even begins to exceed the bound as the size further increases. We explain this behavior of the efficiency at maximum power by using a linear response theory for the heat engine operating under a finite working period, which naturally extends the low-dissipation Carnot cycle model [M. Esposito, R. Kawai, K. Lindenberg, C. Van den Broeck, Phys. Rev. Lett. 105, 150603 (2010)]. The theory also shows that the efficiency at the maximum power under an extreme condition may reach the Carnot efficiency in principle.© EDP Sciences Società Italiana di Fisica Springer-Verlag 2013.

Size dependence of efficiency at maximum power of heat engine

KAUST Repository

Izumida, Y.

2013-10-01

We perform a molecular dynamics computer simulation of a heat engine model to study how the engine size difference affects its performance. Upon tactically increasing the size of the model anisotropically, we determine that there exists an optimum size at which the model attains the maximum power for the shortest working period. This optimum size locates between the ballistic heat transport region and the diffusive heat transport one. We also study the size dependence of the efficiency at the maximum power. Interestingly, we find that the efficiency at the maximum power around the optimum size attains a value that has been proposed as a universal upper bound, and it even begins to exceed the bound as the size further increases. We explain this behavior of the efficiency at maximum power by using a linear response theory for the heat engine operating under a finite working period, which naturally extends the low-dissipation Carnot cycle model [M. Esposito, R. Kawai, K. Lindenberg, C. Van den Broeck, Phys. Rev. Lett. 105, 150603 (2010)]. The theory also shows that the efficiency at the maximum power under an extreme condition may reach the Carnot efficiency in principle.© EDP Sciences Società Italiana di Fisica Springer-Verlag 2013.

Maximum Principle for General Controlled Systems Driven by Fractional Brownian Motions

International Nuclear Information System (INIS)

Han Yuecai; Hu Yaozhong; Song Jian

2013-01-01

We obtain a maximum principle for stochastic control problem of general controlled stochastic differential systems driven by fractional Brownian motions (of Hurst parameter H>1/2). This maximum principle specifies a system of equations that the optimal control must satisfy (necessary condition for the optimal control). This system of equations consists of a backward stochastic differential equation driven by both fractional Brownian motions and the corresponding underlying standard Brownian motions. In addition to this backward equation, the maximum principle also involves the Malliavin derivatives. Our approach is to use conditioning and Malliavin calculus. To arrive at our maximum principle we need to develop some new results of stochastic analysis of the controlled systems driven by fractional Brownian motions via fractional calculus. Our approach of conditioning and Malliavin calculus is also applied to classical system driven by standard Brownian motions while the controller has only partial information. As a straightforward consequence, the classical maximum principle is also deduced in this more natural and simpler way.

Ellipsometry-based combination of isothermal sorption-desorption measurement and temperature programmed desorption technique: A probe for interaction of thin polymer films with solvent vapor

Science.gov (United States)

Efremov, Mikhail Yu.; Nealey, Paul F.

2018-05-01

An environmental chamber equipped with an in situ spectroscopic ellipsometer, programmatic vapor pressure control, and variable temperature substrate holder has been designed for studying polymer coating behavior during an exposure to a solvent vapor and also for probing the residual solvent in the film afterwards. Both sorption-desorption cycle at a constant temperature and temperature programmed desorption (TPD) of the residual solvent manifest themselves as a change of the film thickness. Monitoring of ellipsometric angles of the coating allows us to determine the thickness as a function of the vapor pressure or sample temperature. The solvent vapor pressure is precisely regulated by a computer-controlled pneumatics. TPD spectra are recorded during heating of the film in an oil-free vacuum. The vapor pressure control system is described in detail. The system has been tested on 6-170 nm thick polystyrene, poly(methyl methacrylate), and poly(2-vinyl pyridine) films deposited on silicon substrates. Liquid toluene, water, ethanol, isopropanol, cyclohexane, 1,2-dichloroethane, and chlorobenzene were used to create a vapor atmosphere. Typical sorption-desorption and TPD curves are shown. The instrument achieves sub-monolayer sensitivity for adsorption studies on flat surfaces. Polymer-solvent vapor systems with strong interaction demonstrate characteristic absorption-desorption hysteresis spanning from vacuum to the glass transition pressure. Features on the TPD curves can be classified as either glass transition related film contraction or low temperature broad contraction peak. Typical absorption-desorption and TPD dependencies recorded for the 6 nm thick polystyrene film demonstrate the possibility to apply the presented technique for probing size effects in extremely thin coatings.

A novel strategy for pharmaceutical cocrystal generation without knowledge of stoichiometric ratio: myricetin cocrystals and a ternary phase diagram.

Science.gov (United States)

Hong, Chao; Xie, Yan; Yao, Yashu; Li, Guowen; Yuan, Xiurong; Shen, Hongyi

2015-01-01

To develop a streamlined strategy for pharmaceutical cocrystal preparation without knowledge of the stoichiometric ratio by preparing and characterizing the cocrystals of myricetin (MYR) with four cocrystal coformers (CCF). An approach based on the phase solubility diagram (PSD) was used for MYR cocrystals preparation and the solid-state properties were characterized by differential scanning calorimetry (DSC), fourier transform-infrared spectroscopy (FT-IR), powder X-ray diffraction (PXRD), and scanning electron microscopy (SEM). The ternary phase diagram (TPD) was constructed by combining the PSD and nuclear magnetic resonance (NMR) data. After that, the TPD was verified by traditional methods. The dissolution of MYR in the four cocrystals and pure MYR within three different media were also evaluated. A simple research method for MYR cocrystal preparation was obtained as follows: first, the PSD of MYR and CCF was constructed and analyzed; second, by transforming the curve in the PSD to a TPD, a region of pure cocrystals formation was exhibited, and then MYR cocrystals were prepared and identified by DSC, FT-IR, PXRD, and SEM; third, with the composition of the prepared cocrystal from NMR, the TPD of the MYR-CCF-Solvent system was constructed. The powder dissolution data showed that the solubility and dissolution rate of MYR was significantly enhanced by the cocrystals. A novel strategy for pharmaceutical cocrystals preparation without knowledge of the stoichiometric ratio based on the TPD was established and MYR cocrystals were successfully prepared. The present study provides a systematic approach for pharmaceutical cocrystal generation, which benefits the development and application of cocrystal technology in drug delivery.

Elaboration of thorium uranium phosphate-diphosphate({beta}-TUPD) and {beta}-TUPD/monazite composite materials from crystallized precursors: sintering and study of the long term behavior of the ceramics; Elaboration de phosphate-diphosphate de thorium et d'uranium ({beta}-PDTU) et de materiaux composites {beta}-PDTU/Monazite a partir de precurseurs cristallises. Etudes du frittage et de la durabilite chimique

Energy Technology Data Exchange (ETDEWEB)

Clavier, N

2004-11-01

Thorium Phosphate-Diphosphate ({beta}-TPD) is actually considered as potential host matrix for the immobilization of radionuclides, and especially actinides, in the field of an underground repository. The studies reported in this work are based on the precipitation of the Thorium Phosphate Hydrogen-Phosphate Hydrate (TPHPH) as a precursor of {beta}-TPD. The crystal structure of TPHPH was solved then the reactions involved during its transformation into {beta}-TPD were established. It allows us to put in evidence a new monoclinic variety of TPD, called {alpha}-TPD, acting as intermediate of reaction. Moreover, the existence of a complete solid solution between TPHPH and UPHPH was demonstrated.The experimental conditions of sintering leading to an optimal densification of the pellets were determined. The relative density of the samples was always between 95 and 100% of the calculated value while a significant improvement of the homogeneity of the samples was noted. By this way, the process based on the precipitation of low-temperature crystallized precursors followed by their heat treatment at high temperature was applied to the preparation of {beta}-TUPD/Monazite based composites in the aim to incorporate simultaneously tri- and tetravalent actinides. The chemical durability of {beta}-TUPD sintered samples was evaluated. The normalized leaching rates determined in several experimental conditions revealed the good resistance of the solids to aqueous alteration. Moreover, the normalized dissolution rates exhibited a low dependence to temperature, pH as well as to several ions present in the leachate. For all the samples, thorium was quickly precipitated as a neo-formed phosphate phase identified to TPHPH. (author)

Direct maximum parsimony phylogeny reconstruction from genotype data.

Science.gov (United States)

Sridhar, Srinath; Lam, Fumei; Blelloch, Guy E; Ravi, R; Schwartz, Russell

2007-12-05

Maximum parsimony phylogenetic tree reconstruction from genetic variation data is a fundamental problem in computational genetics with many practical applications in population genetics, whole genome analysis, and the search for genetic predictors of disease. Efficient methods are available for reconstruction of maximum parsimony trees from haplotype data, but such data are difficult to determine directly for autosomal DNA. Data more commonly is available in the form of genotypes, which consist of conflated combinations of pairs of haplotypes from homologous chromosomes. Currently, there are no general algorithms for the direct reconstruction of maximum parsimony phylogenies from genotype data. Hence phylogenetic applications for autosomal data must therefore rely on other methods for first computationally inferring haplotypes from genotypes. In this work, we develop the first practical method for computing maximum parsimony phylogenies directly from genotype data. We show that the standard practice of first inferring haplotypes from genotypes and then reconstructing a phylogeny on the haplotypes often substantially overestimates phylogeny size. As an immediate application, our method can be used to determine the minimum number of mutations required to explain a given set of observed genotypes. Phylogeny reconstruction directly from unphased data is computationally feasible for moderate-sized problem instances and can lead to substantially more accurate tree size inferences than the standard practice of treating phasing and phylogeny construction as two separate analysis stages. The difference between the approaches is particularly important for downstream applications that require a lower-bound on the number of mutations that the genetic region has undergone.

Direct maximum parsimony phylogeny reconstruction from genotype data

Directory of Open Access Journals (Sweden)

Ravi R

2007-12-01

Full Text Available Abstract Background Maximum parsimony phylogenetic tree reconstruction from genetic variation data is a fundamental problem in computational genetics with many practical applications in population genetics, whole genome analysis, and the search for genetic predictors of disease. Efficient methods are available for reconstruction of maximum parsimony trees from haplotype data, but such data are difficult to determine directly for autosomal DNA. Data more commonly is available in the form of genotypes, which consist of conflated combinations of pairs of haplotypes from homologous chromosomes. Currently, there are no general algorithms for the direct reconstruction of maximum parsimony phylogenies from genotype data. Hence phylogenetic applications for autosomal data must therefore rely on other methods for first computationally inferring haplotypes from genotypes. Results In this work, we develop the first practical method for computing maximum parsimony phylogenies directly from genotype data. We show that the standard practice of first inferring haplotypes from genotypes and then reconstructing a phylogeny on the haplotypes often substantially overestimates phylogeny size. As an immediate application, our method can be used to determine the minimum number of mutations required to explain a given set of observed genotypes. Conclusion Phylogeny reconstruction directly from unphased data is computationally feasible for moderate-sized problem instances and can lead to substantially more accurate tree size inferences than the standard practice of treating phasing and phylogeny construction as two separate analysis stages. The difference between the approaches is particularly important for downstream applications that require a lower-bound on the number of mutations that the genetic region has undergone.

20 CFR 10.806 - How are the maximum fees defined?

Science.gov (United States)

2010-04-01

... AMENDED Information for Medical Providers Medical Fee Schedule § 10.806 How are the maximum fees defined? For professional medical services, the Director shall maintain a schedule of maximum allowable fees.../Current Procedural Terminology (HCPCS/CPT) code which represents the relative skill, effort, risk and time...

Maximum-likelihood estimation of the hyperbolic parameters from grouped observations

DEFF Research Database (Denmark)

Jensen, Jens Ledet

1988-01-01

a least-squares problem. The second procedure Hypesti first approaches the maximum-likelihood estimate by iterating in the profile-log likelihood function for the scale parameter. Close to the maximum of the likelihood function, the estimation is brought to an end by iteration, using all four parameters...

Scientific substantination of maximum allowable concentration of fluopicolide in water

Directory of Open Access Journals (Sweden)

Pelo I.М.

2014-03-01

Full Text Available In order to substantiate fluopicolide maximum allowable concentration in the water of water reservoirs the research was carried out. Methods of study: laboratory hygienic experiment using organoleptic and sanitary-chemical, sanitary-toxicological, sanitary-microbiological and mathematical methods. The results of fluopicolide influence on organoleptic properties of water, sanitary regimen of reservoirs for household purposes were given and its subthreshold concentration in water by sanitary and toxicological hazard index was calculated. The threshold concentration of the substance by the main hazard criteria was established, the maximum allowable concentration in water was substantiated. The studies led to the following conclusions: fluopicolide threshold concentration in water by organoleptic hazard index (limiting criterion – the smell – 0.15 mg/dm3, general sanitary hazard index (limiting criteria – impact on the number of saprophytic microflora, biochemical oxygen demand and nitrification – 0.015 mg/dm3, the maximum noneffective concentration – 0.14 mg/dm3, the maximum allowable concentration - 0.015 mg/dm3.

Maximum likelihood estimation of finite mixture model for economic data

Science.gov (United States)

Phoong, Seuk-Yen; Ismail, Mohd Tahir

2014-06-01

Finite mixture model is a mixture model with finite-dimension. This models are provides a natural representation of heterogeneity in a finite number of latent classes. In addition, finite mixture models also known as latent class models or unsupervised learning models. Recently, maximum likelihood estimation fitted finite mixture models has greatly drawn statistician's attention. The main reason is because maximum likelihood estimation is a powerful statistical method which provides consistent findings as the sample sizes increases to infinity. Thus, the application of maximum likelihood estimation is used to fit finite mixture model in the present paper in order to explore the relationship between nonlinear economic data. In this paper, a two-component normal mixture model is fitted by maximum likelihood estimation in order to investigate the relationship among stock market price and rubber price for sampled countries. Results described that there is a negative effect among rubber price and stock market price for Malaysia, Thailand, Philippines and Indonesia.

Comparison of Protein Value of Commercial Baby Food with Homemade Baby Food and Casein Standard in Rats as the Refference point

Directory of Open Access Journals (Sweden)

Z Asemi

2012-05-01

Full Text Available

Background and Objectives

Evaluation of protein quality in food is of great importance due to the  biological and economical impacts of food proteins. This study has been conducted with the aim of comparing the protein quality of  homemade food (mixture of macaroni and soy bean with commercial baby food (Cerelac Wheat using Casein as the refference point.

Methods

This study was conducted on 64 twenty one day old male Wistar rats. The rats were divided into 8 groups, and each group was put on a different diet regiments. The diet regiments were as follow: 2 homemade food+Cerelac test diet, 1 Ccasein+Methionine standard diet, 1 protien-free basal diet, 2 test diet, 1 standard diet and 1 basal diet. The purpose of protien-free diet was  to evaluate True Protien Digestability (TPD. Net Protein Ratio (NPR and Protien Efficiency Ratios (PER were investigated by the basal diet. Protein intake and increasing of weight were determined for NPR and PER calculating. Nitrogen intake and fecal Nitrogen were determined to calculate TPD. Comparison of TPD, NPR and PER among the groups were analyzed by ANOVA and Tukey methods.

Results

TPD values of Standard, Cerelac and homemade food diets were 92.8±4, 87±8 and 85.4±3.2; NPR values were 4.3±0.4, 4.3±0.9, 3.8±0.6; and PER values were 3±0.2, 2.5±0.4, 1.7±0.1 respectively. The statistical difference between TPD and PER values were significant (p < 0.05, whereas NPR differences were insignificant ( p > 0.05.

Conclusion

Efficiency of autonomous soft nanomachines at maximum power.

Science.gov (United States)

Seifert, Udo

2011-01-14

We consider nanosized artificial or biological machines working in steady state enforced by imposing nonequilibrium concentrations of solutes or by applying external forces, torques, or electric fields. For unicyclic and strongly coupled multicyclic machines, efficiency at maximum power is not bounded by the linear response value 1/2. For strong driving, it can even approach the thermodynamic limit 1. Quite generally, such machines fall into three different classes characterized, respectively, as "strong and efficient," "strong and inefficient," and "balanced." For weakly coupled multicyclic machines, efficiency at maximum power has lost any universality even in the linear response regime.

Zipf's law, power laws and maximum entropy

International Nuclear Information System (INIS)

Visser, Matt

2013-01-01

Zipf's law, and power laws in general, have attracted and continue to attract considerable attention in a wide variety of disciplines—from astronomy to demographics to software structure to economics to linguistics to zoology, and even warfare. A recent model of random group formation (RGF) attempts a general explanation of such phenomena based on Jaynes' notion of maximum entropy applied to a particular choice of cost function. In the present paper I argue that the specific cost function used in the RGF model is in fact unnecessarily complicated, and that power laws can be obtained in a much simpler way by applying maximum entropy ideas directly to the Shannon entropy subject only to a single constraint: that the average of the logarithm of the observable quantity is specified. (paper)

Einstein-Dirac theory in spin maximum I

International Nuclear Information System (INIS)

Crumeyrolle, A.

1975-01-01

An unitary Einstein-Dirac theory, first in spin maximum 1, is constructed. An original feature of this article is that it is written without any tetrapod technics; basic notions and existence conditions for spinor structures on pseudo-Riemannian fibre bundles are only used. A coupling gravitation-electromagnetic field is pointed out, in the geometric setting of the tangent bundle over space-time. Generalized Maxwell equations for inductive media in presence of gravitational field are obtained. Enlarged Einstein-Schroedinger theory, gives a particular case of this E.D. theory. E. S. theory is a truncated E.D. theory in spin maximum 1. A close relation between torsion-vector and Schroedinger's potential exists and nullity of torsion-vector has a spinor meaning. Finally the Petiau-Duffin-Kemmer theory is incorporated in this geometric setting [fr

Fuzzy Controller Design Using FPGA for Photovoltaic Maximum Power Point Tracking

OpenAIRE

Basil M Hamed; Mohammed S. El-Moghany

2012-01-01

The cell has optimum operating point to be able to get maximum power. To obtain Maximum Power from photovoltaic array, photovoltaic power system usually requires Maximum Power Point Tracking (MPPT) controller. This paper provides a small power photovoltaic control system based on fuzzy control with FPGA technology design and implementation for MPPT. The system composed of photovoltaic module, buck converter and the fuzzy logic controller implemented on FPGA for controlling on/off time of MOSF...

Maximum penetration level of distributed generation without violating voltage limits

NARCIS (Netherlands)

Morren, J.; Haan, de S.W.H.

2009-01-01

Connection of Distributed Generation (DG) units to a distribution network will result in a local voltage increase. As there will be a maximum on the allowable voltage increase, this will limit the maximum allowable penetration level of DG. By reactive power compensation (by the DG unit itself) a

Improvement of carrier transport and luminous efficiency of organic light emitting diodes by introducing a co-deposited active layer

Energy Technology Data Exchange (ETDEWEB)

Ohtani, Naoki; Murata, Masaya; Kashiwabara, Keiichiro; Kurata, Kazunori, E-mail: ohtani@mail.doshisha.ac.j [Department of Electronics, Doshisha University, 3-1 Tatara-Miyakodani, Kyotanabe-shi, Kyoto 610-0321 (Japan)

2009-11-15

We evaluated carrier transport and luminous efficiency of organic light-emitting diodes (OLEDs) whose active regions consist of a single co-deposited layer. One organic material is a hole transport material N,N'-Bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD), while the other is an electron transport/emissive material Tris(8-hydroxyquinolinato)-aluminum (Alq3). It was found that the luminous efficiency strongly depends on the thickness and the ratio of the TPD:Alq3 co-deposited layer. This indicates that the carrier balance in the active region can be improved by changing the co-deposited layers. In addition, we performed the dye-doping method to clarify the recombination region. As a result, we found that the radiative recombination is caused in the whole TPD:Alq3 co-deposited layer.

25 CFR 141.36 - Maximum finance charges on pawn transactions.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Maximum finance charges on pawn transactions. 141.36... PRACTICES ON THE NAVAJO, HOPI AND ZUNI RESERVATIONS Pawnbroker Practices § 141.36 Maximum finance charges on pawn transactions. No pawnbroker may impose an annual finance charge greater than twenty-four percent...

Microprocessor-controlled step-down maximum-power-point tracker for photovoltaic systems

Science.gov (United States)

Mazmuder, R. K.; Haidar, S.

1992-12-01

An efficient maximum power point tracker (MPPT) has been developed and can be used with a photovoltaic (PV) array and a load which requires lower voltage than the PV array voltage to be operated. The MPPT makes the PV array to operate at maximum power point (MPP) under all insolation and temperature, which ensures the maximum amount of available PV power to be delivered to the load. The performance of the MPPT has been studied under different insolation levels.

Introduction to maximum entropy

International Nuclear Information System (INIS)

Sivia, D.S.

1989-01-01

The maximum entropy (MaxEnt) principle has been successfully used in image reconstruction in a wide variety of fields. The author reviews the need for such methods in data analysis and shows, by use of a very simple example, why MaxEnt is to be preferred over other regularizing functions. This leads to a more general interpretation of the MaxEnt method, and its use is illustrated with several different examples. Practical difficulties with non-linear problems still remain, this being highlighted by the notorious phase problem in crystallography. He concludes with an example from neutron scattering, using data from a filter difference spectrometer to contrast MaxEnt with a conventional deconvolution. 12 refs., 8 figs., 1 tab

Probable maximum flood control

International Nuclear Information System (INIS)

DeGabriele, C.E.; Wu, C.L.

1991-11-01

This study proposes preliminary design concepts to protect the waste-handling facilities and all shaft and ramp entries to the underground from the probable maximum flood (PMF) in the current design configuration for the proposed Nevada Nuclear Waste Storage Investigation (NNWSI) repository protection provisions were furnished by the United States Bureau of Reclamation (USSR) or developed from USSR data. Proposed flood protection provisions include site grading, drainage channels, and diversion dikes. Figures are provided to show these proposed flood protection provisions at each area investigated. These areas are the central surface facilities (including the waste-handling building and waste treatment building), tuff ramp portal, waste ramp portal, men-and-materials shaft, emplacement exhaust shaft, and exploratory shafts facility

Introduction to maximum entropy

International Nuclear Information System (INIS)

Sivia, D.S.

1988-01-01

The maximum entropy (MaxEnt) principle has been successfully used in image reconstruction in a wide variety of fields. We review the need for such methods in data analysis and show, by use of a very simple example, why MaxEnt is to be preferred over other regularizing functions. This leads to a more general interpretation of the MaxEnt method, and its use is illustrated with several different examples. Practical difficulties with non-linear problems still remain, this being highlighted by the notorious phase problem in crystallography. We conclude with an example from neutron scattering, using data from a filter difference spectrometer to contrast MaxEnt with a conventional deconvolution. 12 refs., 8 figs., 1 tab

Application of Maximum Entropy Distribution to the Statistical Properties of Wave Groups

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

The new distributions of the statistics of wave groups based on the maximum entropy principle are presented. The maximum entropy distributions appear to be superior to conventional distributions when applied to a limited amount of information. Its applications to the wave group properties show the effectiveness of the maximum entropy distribution. FFT filtering method is employed to obtain the wave envelope fast and efficiently. Comparisons of both the maximum entropy distribution and the distribution of Longuet-Higgins (1984) with the laboratory wind-wave data show that the former gives a better fit.

Maximum-confidence discrimination among symmetric qudit states

International Nuclear Information System (INIS)

Jimenez, O.; Solis-Prosser, M. A.; Delgado, A.; Neves, L.

2011-01-01

We study the maximum-confidence (MC) measurement strategy for discriminating among nonorthogonal symmetric qudit states. Restricting to linearly dependent and equally likely pure states, we find the optimal positive operator valued measure (POVM) that maximizes our confidence in identifying each state in the set and minimizes the probability of obtaining inconclusive results. The physical realization of this POVM is completely determined and it is shown that after an inconclusive outcome, the input states may be mapped into a new set of equiprobable symmetric states, restricted, however, to a subspace of the original qudit Hilbert space. By applying the MC measurement again onto this new set, we can still gain some information about the input states, although with less confidence than before. This leads us to introduce the concept of sequential maximum-confidence (SMC) measurements, where the optimized MC strategy is iterated in as many stages as allowed by the input set, until no further information can be extracted from an inconclusive result. Within each stage of this measurement our confidence in identifying the input states is the highest possible, although it decreases from one stage to the next. In addition, the more stages we accomplish within the maximum allowed, the higher will be the probability of correct identification. We will discuss an explicit example of the optimal SMC measurement applied in the discrimination among four symmetric qutrit states and propose an optical network to implement it.

Dinosaur Metabolism and the Allometry of Maximum Growth Rate

OpenAIRE

Myhrvold, Nathan P.

2016-01-01

The allometry of maximum somatic growth rate has been used in prior studies to classify the metabolic state of both extant vertebrates and dinosaurs. The most recent such studies are reviewed, and their data is reanalyzed. The results of allometric regressions on growth rate are shown to depend on the choice of independent variable; the typical choice used in prior studies introduces a geometric shear transformation that exaggerates the statistical power of the regressions. The maximum growth...

The spectrum of R Cygni during its exceptionally low maximum of 1983

International Nuclear Information System (INIS)

Wallerstein, G.; Dominy, J.F.; Mattei, J.A.; Smith, V.V.

1985-01-01

In 1983 R Cygni experienced its faintest maximum ever recorded. A study of the light curve shows correlations between brightness at maximum and interval from the previous cycle, in the sense that fainter maxima occur later than normal and are followed by maxima that occur earlier than normal. Emission and absorption lines in the optical and near infrared (2.2 μm region) reveal two significant correlations. The amplitude of line doubling is independent of the magnitude at maximum for msub(v)(max)=7.1 to 9.8. The velocities of the emission lines, however, correlate with the magnitude at maximum, in that during bright maxima they are negatively displaced by 15 km s -1 with respect to the red component of absorption lines, while during the faintest maximum there is no displacement. (author)

Maximum likelihood estimation for integrated diffusion processes

DEFF Research Database (Denmark)

Baltazar-Larios, Fernando; Sørensen, Michael

We propose a method for obtaining maximum likelihood estimates of parameters in diffusion models when the data is a discrete time sample of the integral of the process, while no direct observations of the process itself are available. The data are, moreover, assumed to be contaminated...... EM-algorithm to obtain maximum likelihood estimates of the parameters in the diffusion model. As part of the algorithm, we use a recent simple method for approximate simulation of diffusion bridges. In simulation studies for the Ornstein-Uhlenbeck process and the CIR process the proposed method works...... by measurement errors. Integrated volatility is an example of this type of observations. Another example is ice-core data on oxygen isotopes used to investigate paleo-temperatures. The data can be viewed as incomplete observations of a model with a tractable likelihood function. Therefore we propose a simulated...

Pareto versus lognormal: a maximum entropy test.

Science.gov (United States)

Bee, Marco; Riccaboni, Massimo; Schiavo, Stefano

2011-08-01

It is commonly found that distributions that seem to be lognormal over a broad range change to a power-law (Pareto) distribution for the last few percentiles. The distributions of many physical, natural, and social events (earthquake size, species abundance, income and wealth, as well as file, city, and firm sizes) display this structure. We present a test for the occurrence of power-law tails in statistical distributions based on maximum entropy. This methodology allows one to identify the true data-generating processes even in the case when it is neither lognormal nor Pareto. The maximum entropy approach is then compared with other widely used methods and applied to different levels of aggregation of complex systems. Our results provide support for the theory that distributions with lognormal body and Pareto tail can be generated as mixtures of lognormally distributed units.

7 CFR 762.129 - Percent of guarantee and maximum loss.

Science.gov (United States)

2010-01-01

... loss. (a) General. The percent of guarantee will not exceed 90 percent based on the credit risk to the lender and the Agency both before and after the transaction. The Agency will determine the percentage of... PLP lenders will not be less than 80 percent. (d) Maximum loss. The maximum amount the Agency will pay...

On the maximum entropy distributions of inherently positive nuclear data

Energy Technology Data Exchange (ETDEWEB)

Taavitsainen, A., E-mail: aapo.taavitsainen@gmail.com; Vanhanen, R.

2017-05-11

The multivariate log-normal distribution is used by many authors and statistical uncertainty propagation programs for inherently positive quantities. Sometimes it is claimed that the log-normal distribution results from the maximum entropy principle, if only means, covariances and inherent positiveness of quantities are known or assumed to be known. In this article we show that this is not true. Assuming a constant prior distribution, the maximum entropy distribution is in fact a truncated multivariate normal distribution – whenever it exists. However, its practical application to multidimensional cases is hindered by lack of a method to compute its location and scale parameters from means and covariances. Therefore, regardless of its theoretical disadvantage, use of other distributions seems to be a practical necessity. - Highlights: • Statistical uncertainty propagation requires a sampling distribution. • The objective distribution of inherently positive quantities is determined. • The objectivity is based on the maximum entropy principle. • The maximum entropy distribution is the truncated normal distribution. • Applicability of log-normal or normal distribution approximation is limited.

Effects of fasting on maximum thermogenesis in temperature-acclimated rats

Science.gov (United States)

Wang, L. C. H.

1981-09-01

To further investigate the limiting effect of substrates on maximum thermogenesis in acute cold exposure, the present study examined the prevalence of this effect at different thermogenic capabilities consequent to cold- or warm-acclimation. Male Sprague-Dawley rats (n=11) were acclimated to 6, 16 and 26‡C, in succession, their thermogenic capabilities after each acclimation temperature were measured under helium-oxygen (21% oxygen, balance helium) at -10‡C after overnight fasting or feeding. Regardless of feeding conditions, both maximum and total heat production were significantly greater in 6>16>26‡C-acclimated conditions. In the fed state, the total heat production was significantly greater than that in the fasted state at all acclimating temperatures but the maximum thermogenesis was significant greater only in the 6 and 16‡C-acclimated states. The results indicate that the limiting effect of substrates on maximum and total thermogenesis is independent of the magnitude of thermogenic capability, suggesting a substrate-dependent component in restricting the effective expression of existing aerobic metabolic capability even under severe stress.

Maximum gain of Yagi-Uda arrays

DEFF Research Database (Denmark)

Bojsen, J.H.; Schjær-Jacobsen, Hans; Nilsson, E.

1971-01-01

Numerical optimisation techniques have been used to find the maximum gain of some specific parasitic arrays. The gain of an array of infinitely thin, equispaced dipoles loaded with arbitrary reactances has been optimised. The results show that standard travelling-wave design methods are not optimum....... Yagi–Uda arrays with equal and unequal spacing have also been optimised with experimental verification....

Solar Maximum Mission Experiment - Ultraviolet Spectroscopy and Polarimetry on the Solar Maximum Mission

Science.gov (United States)

Tandberg-Hanssen, E.; Cheng, C. C.; Woodgate, B. E.; Brandt, J. C.; Chapman, R. D.; Athay, R. G.; Beckers, J. M.; Bruner, E. C.; Gurman, J. B.; Hyder, C. L.

1981-01-01

The Ultraviolet Spectrometer and Polarimeter on the Solar Maximum Mission spacecraft is described. It is pointed out that the instrument, which operates in the wavelength range 1150-3600 A, has a spatial resolution of 2-3 arcsec and a spectral resolution of 0.02 A FWHM in second order. A Gregorian telescope, with a focal length of 1.8 m, feeds a 1 m Ebert-Fastie spectrometer. A polarimeter comprising rotating Mg F2 waveplates can be inserted behind the spectrometer entrance slit; it permits all four Stokes parameters to be determined. Among the observing modes are rasters, spectral scans, velocity measurements, and polarimetry. Examples of initial observations made since launch are presented.

Maximum β limited by ideal MHD ballooning instabilites in JT-60

International Nuclear Information System (INIS)

Seki, Shogo; Azumi, Masashi

1986-03-01

Maximum β limited by ideal MHD ballooning instabilities is investigated on divertor configurations in JT-60. Maximum β against ballooning modes in JT-60 has strong dependecy on the distribution of the safety factor over the magnetic surfaces. Maximum β is ∼ 2 % for q 0 = 1.0, while more than 3 % for q 0 = 1.5. These results suggest that the profile control of the safety factor, especially on the magnetic axis, is attractive to the higher β operation in JT-60. (author)

A maximum principle for time dependent transport in systems with voids

International Nuclear Information System (INIS)

Schofield, S.L.; Ackroyd, R.T.

1996-01-01

A maximum principle is developed for the first-order time dependent Boltzmann equation. The maximum principle is a generalization of Schofield's κ(θ) principle for the first-order steady state Boltzmann equation, and provides a treatment of time dependent transport in systems with void regions. The formulation comprises a direct least-squares minimization allied with a suitable choice of bilinear functional, and gives rise to a maximum principle whose functional is free of terms that have previously led to difficulties in treating void regions. (Author)

The maximum sizes of large scale structures in alternative theories of gravity

Energy Technology Data Exchange (ETDEWEB)

Bhattacharya, Sourav [IUCAA, Pune University Campus, Post Bag 4, Ganeshkhind, Pune, 411 007 India (India); Dialektopoulos, Konstantinos F. [Dipartimento di Fisica, Università di Napoli ' Federico II' , Complesso Universitario di Monte S. Angelo, Edificio G, Via Cinthia, Napoli, I-80126 Italy (Italy); Romano, Antonio Enea [Instituto de Física, Universidad de Antioquia, Calle 70 No. 52–21, Medellín (Colombia); Skordis, Constantinos [Department of Physics, University of Cyprus, 1 Panepistimiou Street, Nicosia, 2109 Cyprus (Cyprus); Tomaras, Theodore N., E-mail: sbhatta@iitrpr.ac.in, E-mail: kdialekt@gmail.com, E-mail: aer@phys.ntu.edu.tw, E-mail: skordis@ucy.ac.cy, E-mail: tomaras@physics.uoc.gr [Institute of Theoretical and Computational Physics and Department of Physics, University of Crete, 70013 Heraklion (Greece)

2017-07-01

The maximum size of a cosmic structure is given by the maximum turnaround radius—the scale where the attraction due to its mass is balanced by the repulsion due to dark energy. We derive generic formulae for the estimation of the maximum turnaround radius in any theory of gravity obeying the Einstein equivalence principle, in two situations: on a spherically symmetric spacetime and on a perturbed Friedman-Robertson-Walker spacetime. We show that the two formulae agree. As an application of our formula, we calculate the maximum turnaround radius in the case of the Brans-Dicke theory of gravity. We find that for this theory, such maximum sizes always lie above the ΛCDM value, by a factor 1 + 1/3ω, where ω>> 1 is the Brans-Dicke parameter, implying consistency of the theory with current data.

Maximum nondiffracting propagation distance of aperture-truncated Airy beams

Science.gov (United States)

Chu, Xingchun; Zhao, Shanghong; Fang, Yingwu

2018-05-01

Airy beams have called attention of many researchers due to their non-diffracting, self-healing and transverse accelerating properties. A key issue in research of Airy beams and its applications is how to evaluate their nondiffracting propagation distance. In this paper, the critical transverse extent of physically realizable Airy beams is analyzed under the local spatial frequency methodology. The maximum nondiffracting propagation distance of aperture-truncated Airy beams is formulated and analyzed based on their local spatial frequency. The validity of the formula is verified by comparing the maximum nondiffracting propagation distance of an aperture-truncated ideal Airy beam, aperture-truncated exponentially decaying Airy beam and exponentially decaying Airy beam. Results show that the formula can be used to evaluate accurately the maximum nondiffracting propagation distance of an aperture-truncated ideal Airy beam. Therefore, it can guide us to select appropriate parameters to generate Airy beams with long nondiffracting propagation distance that have potential application in the fields of laser weapons or optical communications.

Maximum Entropy and Theory Construction: A Reply to Favretti

Directory of Open Access Journals (Sweden)

John Harte

2018-04-01

Full Text Available In the maximum entropy theory of ecology (METE, the form of a function describing the distribution of abundances over species and metabolic rates over individuals in an ecosystem is inferred using the maximum entropy inference procedure. Favretti shows that an alternative maximum entropy model exists that assumes the same prior knowledge and makes predictions that differ from METE’s. He shows that both cannot be correct and asserts that his is the correct one because it can be derived from a classic microstate-counting calculation. I clarify here exactly what the core entities and definitions are for METE, and discuss the relevance of two critical issues raised by Favretti: the existence of a counting procedure for microstates and the choices of definition of the core elements of a theory. I emphasize that a theorist controls how the core entities of his or her theory are defined, and that nature is the final arbiter of the validity of a theory.

A novel algorithm for single-axis maximum power generation sun trackers

International Nuclear Information System (INIS)

Lee, Kung-Yen; Chung, Chi-Yao; Huang, Bin-Juine; Kuo, Ting-Jung; Yang, Huang-Wei; Cheng, Hung-Yen; Hsu, Po-Chien; Li, Kang

2017-01-01

Highlights: • A novel algorithm for a single-axis sun tracker is developed to increase the efficiency. • Photovoltaic module is rotated to find the optimal angle for generating the maximum power. • Electric energy increases up to 8.3%, compared with that of the tracker with three fixed angles. • The rotation range is optimized to reduce energy consumption from the rotation operations. - Abstract: The purpose of this study is to develop a novel algorithm for a single-axis maximum power generation sun tracker in order to identify the optimal stopping angle for generating the maximum amount of daily electric energy. First, the photovoltaic modules of the single-axis maximum power generation sun tracker are automatically rotated from 50° east to 50° west. During the rotation, the instantaneous power generated at different angles is recorded and compared, meaning that the optimal angle for generating the maximum power can be determined. Once the rotation (detection) is completed, the photovoltaic modules are then rotated to the resulting angle for generating the maximum power. The photovoltaic module is rotated once per hour in an attempt to detect the maximum irradiation and overcome the impact of environmental effects such as shading from cloud cover, other photovoltaic modules and surrounding buildings. Furthermore, the detection range is halved so as to reduce the energy consumption from the rotation operations and to improve the reliability of the sun tracker. The results indicate that electric energy production is increased by 3.4% in spring and autumn, 5.4% in summer, and 8.3% in winter, compared with that of the same sun tracker with three fixed angles of 50° east in the morning, 0° at noon and 50° west in the afternoon.

Effects of variability in probable maximum precipitation patterns on flood losses

Science.gov (United States)

Zischg, Andreas Paul; Felder, Guido; Weingartner, Rolf; Quinn, Niall; Coxon, Gemma; Neal, Jeffrey; Freer, Jim; Bates, Paul

2018-05-01

The assessment of the impacts of extreme floods is important for dealing with residual risk, particularly for critical infrastructure management and for insurance purposes. Thus, modelling of the probable maximum flood (PMF) from probable maximum precipitation (PMP) by coupling hydrological and hydraulic models has gained interest in recent years. Herein, we examine whether variability in precipitation patterns exceeds or is below selected uncertainty factors in flood loss estimation and if the flood losses within a river basin are related to the probable maximum discharge at the basin outlet. We developed a model experiment with an ensemble of probable maximum precipitation scenarios created by Monte Carlo simulations. For each rainfall pattern, we computed the flood losses with a model chain and benchmarked the effects of variability in rainfall distribution with other model uncertainties. The results show that flood losses vary considerably within the river basin and depend on the timing and superimposition of the flood peaks from the basin's sub-catchments. In addition to the flood hazard component, the other components of flood risk, exposure, and vulnerability contribute remarkably to the overall variability. This leads to the conclusion that the estimation of the probable maximum expectable flood losses in a river basin should not be based exclusively on the PMF. Consequently, the basin-specific sensitivities to different precipitation patterns and the spatial organization of the settlements within the river basin need to be considered in the analyses of probable maximum flood losses.

Maximum potential preventive effect of hip protectors

NARCIS (Netherlands)

van Schoor, N.M.; Smit, J.H.; Bouter, L.M.; Veenings, B.; Asma, G.B.; Lips, P.T.A.M.

2007-01-01

OBJECTIVES: To estimate the maximum potential preventive effect of hip protectors in older persons living in the community or homes for the elderly. DESIGN: Observational cohort study. SETTING: Emergency departments in the Netherlands. PARTICIPANTS: Hip fracture patients aged 70 and older who

24 CFR 232.565 - Maximum loan amount.

Science.gov (United States)

2010-04-01

... URBAN DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES MORTGAGE INSURANCE FOR NURSING HOMES, INTERMEDIATE CARE FACILITIES, BOARD AND CARE HOMES, AND ASSISTED... Fire Safety Equipment Eligible Security Instruments § 232.565 Maximum loan amount. The principal amount...

Achieving maximum sustainable yield in mixed fisheries

NARCIS (Netherlands)

Ulrich, Clara; Vermard, Youen; Dolder, Paul J.; Brunel, Thomas; Jardim, Ernesto; Holmes, Steven J.; Kempf, Alexander; Mortensen, Lars O.; Poos, Jan Jaap; Rindorf, Anna

2017-01-01

Achieving single species maximum sustainable yield (MSY) in complex and dynamic fisheries targeting multiple species (mixed fisheries) is challenging because achieving the objective for one species may mean missing the objective for another. The North Sea mixed fisheries are a representative example

Maximum Power Point Tracking of Photovoltaic System for Traffic Light Application

Directory of Open Access Journals (Sweden)

Riza Muhida

2013-07-01

Full Text Available Photovoltaic traffic light system is a significant application of renewable energy source. The development of the system is an alternative effort of local authority to reduce expenditure for paying fees to power supplier which the power comes from conventional energy source. Since photovoltaic (PV modules still have relatively low conversion efficiency, an alternative control of maximum power point tracking (MPPT method is applied to the traffic light system. MPPT is intended to catch up the maximum power at daytime in order to charge the battery at the maximum rate in which the power from the battery is intended to be used at night time or cloudy day. MPPT is actually a DC-DC converter that can step up or down voltage in order to achieve the maximum power using Pulse Width Modulation (PWM control. From experiment, we obtained the voltage of operation using MPPT is at 16.454 V, this value has error of 2.6%, if we compared with maximum power point voltage of PV module that is 16.9 V. Based on this result it can be said that this MPPT control works successfully to deliver the power from PV module to battery maximally.

Stochastic behavior of a cold standby system with maximum repair time

Directory of Open Access Journals (Sweden)

Ashish Kumar

2015-09-01

Full Text Available The main aim of the present paper is to analyze the stochastic behavior of a cold standby system with concept of preventive maintenance, priority and maximum repair time. For this purpose, a stochastic model is developed in which initially one unit is operative and other is kept as cold standby. There is a single server who visits the system immediately as and when required. The server takes the unit under preventive maintenance after a maximum operation time at normal mode if one standby unit is available for operation. If the repair of the failed unit is not possible up to a maximum repair time, failed unit is replaced by new one. The failure time, maximum operation time and maximum repair time distributions of the unit are considered as exponentially distributed while repair and maintenance time distributions are considered as arbitrary. All random variables are statistically independent and repairs are perfect. Various measures of system effectiveness are obtained by using the technique of semi-Markov process and RPT. To highlight the importance of the study numerical results are also obtained for MTSF, availability and profit function.

Generic maximum likely scale selection

DEFF Research Database (Denmark)

Pedersen, Kim Steenstrup; Loog, Marco; Markussen, Bo

2007-01-01

in this work is on applying this selection principle under a Brownian image model. This image model provides a simple scale invariant prior for natural images and we provide illustrative examples of the behavior of our scale estimation on such images. In these illustrative examples, estimation is based......The fundamental problem of local scale selection is addressed by means of a novel principle, which is based on maximum likelihood estimation. The principle is generally applicable to a broad variety of image models and descriptors, and provides a generic scale estimation methodology. The focus...

Maximum principle and convergence of central schemes based on slope limiters

KAUST Repository

Mehmetoglu, Orhan; Popov, Bojan

2012-01-01

A maximum principle and convergence of second order central schemes is proven for scalar conservation laws in dimension one. It is well known that to establish a maximum principle a nonlinear piecewise linear reconstruction is needed and a typical choice is the minmod limiter. Unfortunately, this implies that the scheme uses a first order reconstruction at local extrema. The novelty here is that we allow local nonlinear reconstructions which do not reduce to first order at local extrema and still prove maximum principle and convergence. © 2011 American Mathematical Society.

Information Entropy Production of Maximum Entropy Markov Chains from Spike Trains

Science.gov (United States)

Cofré, Rodrigo; Maldonado, Cesar

2018-01-01

We consider the maximum entropy Markov chain inference approach to characterize the collective statistics of neuronal spike trains, focusing on the statistical properties of the inferred model. We review large deviations techniques useful in this context to describe properties of accuracy and convergence in terms of sampling size. We use these results to study the statistical fluctuation of correlations, distinguishability and irreversibility of maximum entropy Markov chains. We illustrate these applications using simple examples where the large deviation rate function is explicitly obtained for maximum entropy models of relevance in this field.

Methanol Adsorption and Reaction on Samaria Thin Films on Pt(111

Directory of Open Access Journals (Sweden)

Jin-Hao Jhang

2015-09-01

Full Text Available We investigated the adsorption and reaction of methanol on continuous and discontinuous films of samarium oxide (SmOx grown on Pt(111 in ultrahigh vacuum. The methanol decomposition was studied by temperature programmed desorption (TPD and infrared reflection absorption spectroscopy (IRRAS, while structural changes of the oxide surface were monitored by low-energy electron diffraction (LEED. Methanol dehydrogenates to adsorbed methoxy species on both the continuous and discontinuous SmOx films, eventually leading to the desorption of CO and H2 which desorbs at temperatures in the range 400–600 K. Small quantities of CO2 are also detected mainly on as-prepared Sm2O3 thin films, but the production of CO2 is limited during repeated TPD runs. The discontinuous film exhibits the highest reactivity compared to the continuous film and the Pt(111 substrate. The reactivity of methanol on reduced and reoxidized films was also investigated, revealing how SmOx structures influence the chemical behavior. Over repeated TPD experiments, a SmOx structural/chemical equilibrium condition is found which can be approached either from oxidized or reduced films. We also observed hydrogen absence in TPD which indicates that hydrogen is stored either in SmOx films or as OH groups on the SmOx surfaces.

Hydrogenation of Phenylacetylene to Styrene on Pre-C_xH_y- and C-Covered Cu(111) Single Crystal Catalysts

International Nuclear Information System (INIS)

Sohn, Young Ku; Wei, Wei; White, John M.

2011-01-01

Thermal hydrogenation of phenylacetylene (PA, C_8H_6) to styrene (C_8H_8) on pre-C_xH_y- and C-covered Cu(111) single crystal substrates has been studied using temperature-programmed desorption (TPD) mass spectrometry. Chemisorbed PA with an acetylene group has been proved to be associated with hydrogen of pre-adsorbed C_xH_y to form styrene (104 amu) on Cu surface. For the parent (PA) mass (102 amu) TPD profile, the TPD peaks at 360 K and 410 K are assigned to chemisorbed vertically aligned PA and flat-lying cross-bridged PA, respectively (J. Phys. Chem. C 2007, 111, 5101). The relative I_3_6_0_K/I_4_1_0_K TPD ratio dramatically increases with increasing pre-adsorbed C_xH_y before dosing PA, while the ratio does not increase for pre-C-covered surface. For PA on pre-C_xH_y-covered Cu(111) surface, styrene desorption is enhanced relative to the parent PA desorption, while styrene formation is dramatically quenched on pre-C-covered (lack of adsorbed hydrogen nearby) surface. It appears that only cross-bridged PA associates with adsorbed hydrogen to form styrene that promptly desorbs at 410 K, while vertically aligned PA is less likely to participate in forming styrene

Interactions on External MOF Surfaces: Desorption of Water and Ethanol from CuBDC Nanosheets.

Science.gov (United States)

Elder, Alexander C; Aleksandrov, Alexandr B; Nair, Sankar; Orlando, Thomas M

2017-10-03

The external surfaces of metal-organic framework (MOF) materials are difficult to experimentally isolate due to the high porosities of these materials. MOF surface surrogates in the form of copper benzenedicarboxylate (CuBDC) nanosheets were synthesized using a bottom-up approach, and the surface interactions of water and ethanol were investigated by temperature-programmed desorption (TPD). A method of analysis of diffusion-influenced TPD was developed to measure the desorption properties of these porous materials. This approach also allows the extraction of diffusion coefficients from TPD data. The transmission Fourier transform infrared spectra, powder X-ray diffraction patterns, and TPD data indicate that water desorbs from CuBDC nanosheets with activation energies of 44 ± 2 kJ/mol at edge sites and 58 ± 1 kJ/mol at external surface and internal and pore sites. Ethanol desorbs with activation energies of 58 ± 1 kJ/mol at internal pore sites and 66 ± 0.4 kJ/mol at external surface sites. Co-adsorption of water and ethanol was also investigated. The presence of ethanol was found to inhibit the desorption of water, resulting in a water desorption process with an activation energy of 68 ± 0.7 kJ/mol.

Maximum power point tracker for photovoltaic power plants

Science.gov (United States)

Arcidiacono, V.; Corsi, S.; Lambri, L.

The paper describes two different closed-loop control criteria for the maximum power point tracking of the voltage-current characteristic of a photovoltaic generator. The two criteria are discussed and compared, inter alia, with regard to the setting-up problems that they pose. Although a detailed analysis is not embarked upon, the paper also provides some quantitative information on the energy advantages obtained by using electronic maximum power point tracking systems, as compared with the situation in which the point of operation of the photovoltaic generator is not controlled at all. Lastly, the paper presents two high-efficiency MPPT converters for experimental photovoltaic plants of the stand-alone and the grid-interconnected type.

Maximum mass-particle velocities in Kantor's information mechanics

International Nuclear Information System (INIS)

Sverdlik, D.I.

1989-01-01

Kantor's information mechanics links phenomena previously regarded as not treatable by a single theory. It is used here to calculate the maximum velocities υ m of single particles. For the electron, υ m /c ∼ 1 - 1.253814 x 10 -77 . The maximum υ m corresponds to υ m /c ∼ 1 -1.097864 x 10 -122 for a single mass particle with a rest mass of 3.078496 x 10 -5 g. This is the fastest that matter can move. Either information mechanics or classical mechanics can be used to show that υ m is less for heavier particles. That υ m is less for lighter particles can be deduced from an information mechanics argument alone

A comparison of methods of predicting maximum oxygen uptake.

OpenAIRE

Grant, S; Corbett, K; Amjad, A M; Wilson, J; Aitchison, T

1995-01-01

The aim of this study was to compare the results from a Cooper walk run test, a multistage shuttle run test, and a submaximal cycle test with the direct measurement of maximum oxygen uptake on a treadmill. Three predictive tests of maximum oxygen uptake--linear extrapolation of heart rate of VO2 collected from a submaximal cycle ergometer test (predicted L/E), the Cooper 12 min walk, run test, and a multi-stage progressive shuttle run test (MST)--were performed by 22 young healthy males (mean...

A Maximum Entropy Method for a Robust Portfolio Problem

Directory of Open Access Journals (Sweden)

Yingying Xu

2014-06-01

Full Text Available We propose a continuous maximum entropy method to investigate the robustoptimal portfolio selection problem for the market with transaction costs and dividends.This robust model aims to maximize the worst-case portfolio return in the case that allof asset returns lie within some prescribed intervals. A numerical optimal solution tothe problem is obtained by using a continuous maximum entropy method. Furthermore,some numerical experiments indicate that the robust model in this paper can result in betterportfolio performance than a classical mean-variance model.

Rotational state modification and fast ortho-para conversion of H2 trapped within the highly anisotropic potential of Pd(210)

Science.gov (United States)

Ohno, S.; Ivanov, D.; Ogura, S.; Wilde, M.; Arguelles, E. F.; Diño, W. A.; Kasai, H.; Fukutani, K.

2018-02-01

The rotational state and ortho-para conversion of H2 on a Pd(210) surface is investigated with rotational-state-selective temperature-programmed desorption (RS-TPD) and theoretical calculations. The isotope dependence of TPD shows a higher desorption energy for D2 than that for H2, which is ascribed to the rotational and zero-point vibrational energies. The RS-TPD data show that the desorption energy of H2(J =1 ) (J : rotational quantum number) is higher than that of H2(J =0 ). This is due to the orientationally anisotropic potential confining the adsorbed H2, which is in agreement with theoretical calculations. Furthermore, the H2 desorption intensity ratio in J =1 and J =0 indicates fast ortho-para conversion in the adsorption state, which we estimate to be of the order of 1 s.

Acidity, oxophilicity and hydrogen sticking probability of supported metal catalysts for hydrodeoxygenation process

Science.gov (United States)

Lup, A. Ng K.; Abnisa, F.; Daud, W. M. A. W.; Aroua, M. K.

2018-03-01

Hydrodeoxygenation is an oxygen removal process that occurs in the presence of hydrogen and catalysts. This study has shown the importance of acidity, oxophilicity and hydrogen sticking probability of supported metal catalysts in having high hydrodeoxygenation activity and selectivity. These properties are required to ensure the catalyst has high affinity for C-O or C=O bonds and the capability for the adsorption and activation of H2 and O-containing compounds. A theoretical framework of temperature programmed desorption technique was also discussed for the quantitative understanding of these properties. By using NH3-TPD, the nature and abundance of acid sites of catalyst can be determined. By using H2-TPD, the nature and abundance of metallic sites can also be determined. The desorption activation energy could also be determined based on the Redhead analysis of TPD spectra with different heating rates.

Hydraulic Limits on Maximum Plant Transpiration

Science.gov (United States)

Manzoni, S.; Vico, G.; Katul, G. G.; Palmroth, S.; Jackson, R. B.; Porporato, A. M.

2011-12-01

Photosynthesis occurs at the expense of water losses through transpiration. As a consequence of this basic carbon-water interaction at the leaf level, plant growth and ecosystem carbon exchanges are tightly coupled to transpiration. In this contribution, the hydraulic constraints that limit transpiration rates under well-watered conditions are examined across plant functional types and climates. The potential water flow through plants is proportional to both xylem hydraulic conductivity (which depends on plant carbon economy) and the difference in water potential between the soil and the atmosphere (the driving force that pulls water from the soil). Differently from previous works, we study how this potential flux changes with the amplitude of the driving force (i.e., we focus on xylem properties and not on stomatal regulation). Xylem hydraulic conductivity decreases as the driving force increases due to cavitation of the tissues. As a result of this negative feedback, more negative leaf (and xylem) water potentials would provide a stronger driving force for water transport, while at the same time limiting xylem hydraulic conductivity due to cavitation. Here, the leaf water potential value that allows an optimum balance between driving force and xylem conductivity is quantified, thus defining the maximum transpiration rate that can be sustained by the soil-to-leaf hydraulic system. To apply the proposed framework at the global scale, a novel database of xylem conductivity and cavitation vulnerability across plant types and biomes is developed. Conductivity and water potential at 50% cavitation are shown to be complementary (in particular between angiosperms and conifers), suggesting a tradeoff between transport efficiency and hydraulic safety. Plants from warmer and drier biomes tend to achieve larger maximum transpiration than plants growing in environments with lower atmospheric water demand. The predicted maximum transpiration and the corresponding leaf water

correlation between maximum dry density and cohesion

African Journals Online (AJOL)

HOD

represents maximum dry density, signifies plastic limit and is liquid limit. Researchers [6, 7] estimate compaction parameters. Aside from the correlation existing between compaction parameters and other physical quantities there are some other correlations that have been investigated by other researchers. The well-known.

Maximum Work of Free-Piston Stirling Engine Generators

Science.gov (United States)

Kojima, Shinji

2017-04-01

Using the method of adjoint equations described in Ref. [1], we have calculated the maximum thermal efficiencies that are theoretically attainable by free-piston Stirling and Carnot engine generators by considering the work loss due to friction and Joule heat. The net work done by the Carnot cycle is negative even when the duration of heat addition is optimized to give the maximum amount of heat addition, which is the same situation for the Brayton cycle described in our previous paper. For the Stirling cycle, the net work done is positive, and the thermal efficiency is greater than that of the Otto cycle described in our previous paper by a factor of about 2.7-1.4 for compression ratios of 5-30. The Stirling cycle is much better than the Otto, Brayton, and Carnot cycles. We have found that the optimized piston trajectories of the isothermal, isobaric, and adiabatic processes are the same when the compression ratio and the maximum volume of the same working fluid of the three processes are the same, which has facilitated the present analysis because the optimized piston trajectories of the Carnot and Stirling cycles are the same as those of the Brayton and Otto cycles, respectively.

40 CFR 141.51 - Maximum contaminant level goals for inorganic contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for inorganic contaminants. 141.51 Section 141.51 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level...

40 CFR 141.50 - Maximum contaminant level goals for organic contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for organic contaminants. 141.50 Section 141.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level...

40 CFR 141.52 - Maximum contaminant level goals for microbiological contaminants.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for microbiological contaminants. 141.52 Section 141.52 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level...

Solar maximum mission

International Nuclear Information System (INIS)

Ryan, J.

1981-01-01

By understanding the sun, astrophysicists hope to expand this knowledge to understanding other stars. To study the sun, NASA launched a satellite on February 14, 1980. The project is named the Solar Maximum Mission (SMM). The satellite conducted detailed observations of the sun in collaboration with other satellites and ground-based optical and radio observations until its failure 10 months into the mission. The main objective of the SMM was to investigate one aspect of solar activity: solar flares. A brief description of the flare mechanism is given. The SMM satellite was valuable in providing information on where and how a solar flare occurs. A sequence of photographs of a solar flare taken from SMM satellite shows how a solar flare develops in a particular layer of the solar atmosphere. Two flares especially suitable for detailed observations by a joint effort occurred on April 30 and May 21 of 1980. These flares and observations of the flares are discussed. Also discussed are significant discoveries made by individual experiments

SUPPLEMENTARY INFORMATION Green synthetic route for ...

Indian Academy of Sciences (India)

GDY13

Catalyst synthesis. S3. 2. Catalyst characterisation Techniques. S3. 3. NH3-TPD of 0.1% Li/MgO. S3. 4. Proof for absence of external mass transfer resistance. S4. 5. Proof of absence of intra-particle resistance. S5. List of Figures: No. Title. Page No. Figure S1 10% NH3-TPD of 0.1% Li/MgO. S4. Figure S2 SEM of pure MgO.

How long do centenarians survive? Life expectancy and maximum lifespan.

Science.gov (United States)

Modig, K; Andersson, T; Vaupel, J; Rau, R; Ahlbom, A

2017-08-01

The purpose of this study was to explore the pattern of mortality above the age of 100 years. In particular, we aimed to examine whether Scandinavian data support the theory that mortality reaches a plateau at particularly old ages. Whether the maximum length of life increases with time was also investigated. The analyses were based on individual level data on all Swedish and Danish centenarians born from 1870 to 1901; in total 3006 men and 10 963 women were included. Birth cohort-specific probabilities of dying were calculated. Exact ages were used for calculations of maximum length of life. Whether maximum age changed over time was analysed taking into account increases in cohort size. The results confirm that there has not been any improvement in mortality amongst centenarians in the past 30 years and that the current rise in life expectancy is driven by reductions in mortality below the age of 100 years. The death risks seem to reach a plateau of around 50% at the age 103 years for men and 107 years for women. Despite the rising life expectancy, the maximum age does not appear to increase, in particular after accounting for the increasing number of individuals of advanced age. Mortality amongst centenarians is not changing despite improvements at younger ages. An extension of the maximum lifespan and a sizeable extension of life expectancy both require reductions in mortality above the age of 100 years. © 2017 The Association for the Publication of the Journal of Internal Medicine.

Modelling information flow along the human connectome using maximum flow.

Science.gov (United States)

Lyoo, Youngwook; Kim, Jieun E; Yoon, Sujung

2018-01-01

The human connectome is a complex network that transmits information between interlinked brain regions. Using graph theory, previously well-known network measures of integration between brain regions have been constructed under the key assumption that information flows strictly along the shortest paths possible between two nodes. However, it is now apparent that information does flow through non-shortest paths in many real-world networks such as cellular networks, social networks, and the internet. In the current hypothesis, we present a novel framework using the maximum flow to quantify information flow along all possible paths within the brain, so as to implement an analogy to network traffic. We hypothesize that the connection strengths of brain networks represent a limit on the amount of information that can flow through the connections per unit of time. This allows us to compute the maximum amount of information flow between two brain regions along all possible paths. Using this novel framework of maximum flow, previous network topological measures are expanded to account for information flow through non-shortest paths. The most important advantage of the current approach using maximum flow is that it can integrate the weighted connectivity data in a way that better reflects the real information flow of the brain network. The current framework and its concept regarding maximum flow provides insight on how network structure shapes information flow in contrast to graph theory, and suggests future applications such as investigating structural and functional connectomes at a neuronal level. Copyright © 2017 Elsevier Ltd. All rights reserved.

Exploring high-density baryonic matter: Maximum freeze-out density

Energy Technology Data Exchange (ETDEWEB)

Randrup, Joergen [Lawrence Berkeley National Laboratory, Nuclear Science Division, Berkeley, CA (United States); Cleymans, Jean [University of Cape Town, UCT-CERN Research Centre and Department of Physics, Rondebosch (South Africa)

2016-08-15

The hadronic freeze-out line is calculated in terms of the net baryon density and the energy density instead of the usual T and μ{sub B}. This analysis makes it apparent that the freeze-out density exhibits a maximum as the collision energy is varied. This maximum freeze-out density has μ{sub B} = 400 - 500 MeV, which is above the critical value, and it is reached for a fixed-target bombarding energy of 20-30 GeV/N well within the parameters of the proposed NICA collider facility. (orig.)

Maximum organic carbon limits at different melter feed rates (U)

International Nuclear Information System (INIS)

Choi, A.S.

1995-01-01

This report documents the results of a study to assess the impact of varying melter feed rates on the maximum total organic carbon (TOC) limits allowable in the DWPF melter feed. Topics discussed include: carbon content; feed rate; feed composition; melter vapor space temperature; combustion and dilution air; off-gas surges; earlier work on maximum TOC; overview of models; and the results of the work completed

Maximum speed of dewetting on a fiber

NARCIS (Netherlands)

Chan, Tak Shing; Gueudre, Thomas; Snoeijer, Jacobus Hendrikus

2011-01-01

A solid object can be coated by a nonwetting liquid since a receding contact line cannot exceed a critical speed. We theoretically investigate this forced wetting transition for axisymmetric menisci on fibers of varying radii. First, we use a matched asymptotic expansion and derive the maximum speed

Maximum entropy estimation via Gauss-LP quadratures

NARCIS (Netherlands)

Thély, Maxime; Sutter, Tobias; Mohajerin Esfahani, P.; Lygeros, John; Dochain, Denis; Henrion, Didier; Peaucelle, Dimitri

2017-01-01

We present an approximation method to a class of parametric integration problems that naturally appear when solving the dual of the maximum entropy estimation problem. Our method builds up on a recent generalization of Gauss quadratures via an infinite-dimensional linear program, and utilizes a

Maximum Power Tracking by VSAS approach for Wind Turbine, Renewable Energy Sources

Directory of Open Access Journals (Sweden)

Nacer Kouider Msirdi

2015-08-01

Full Text Available This paper gives a review of the most efficient algorithms designed to track the maximum power point (MPP for catching the maximum wind power by a variable speed wind turbine (VSWT. We then design a new maximum power point tracking (MPPT algorithm using the Variable Structure Automatic Systems approach (VSAS. The proposed approachleads efficient algorithms as shown in this paper by the analysis and simulations.

Estimating the maximum potential revenue for grid connected electricity storage :

Energy Technology Data Exchange (ETDEWEB)

Byrne, Raymond Harry; Silva Monroy, Cesar Augusto.

2012-12-01

The valuation of an electricity storage device is based on the expected future cash flow generated by the device. Two potential sources of income for an electricity storage system are energy arbitrage and participation in the frequency regulation market. Energy arbitrage refers to purchasing (stor- ing) energy when electricity prices are low, and selling (discharging) energy when electricity prices are high. Frequency regulation is an ancillary service geared towards maintaining system frequency, and is typically procured by the independent system operator in some type of market. This paper outlines the calculations required to estimate the maximum potential revenue from participating in these two activities. First, a mathematical model is presented for the state of charge as a function of the storage device parameters and the quantities of electricity purchased/sold as well as the quantities o ered into the regulation market. Using this mathematical model, we present a linear programming optimization approach to calculating the maximum potential revenue from an elec- tricity storage device. The calculation of the maximum potential revenue is critical in developing an upper bound on the value of storage, as a benchmark for evaluating potential trading strate- gies, and a tool for capital nance risk assessment. Then, we use historical California Independent System Operator (CAISO) data from 2010-2011 to evaluate the maximum potential revenue from the Tehachapi wind energy storage project, an American Recovery and Reinvestment Act of 2009 (ARRA) energy storage demonstration project. We investigate the maximum potential revenue from two di erent scenarios: arbitrage only and arbitrage combined with the regulation market. Our analysis shows that participation in the regulation market produces four times the revenue compared to arbitrage in the CAISO market using 2010 and 2011 data. Then we evaluate several trading strategies to illustrate how they compare to the

12 CFR 221.7 - Supplement: Maximum loan value of margin stock and other collateral.

Science.gov (United States)

2010-01-01

... value of margin stock and other collateral. (a) Maximum loan value of margin stock. The maximum loan... nonmargin stock and all other collateral. The maximum loan value of nonmargin stock and all other collateral... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Supplement: Maximum loan value of margin stock...

MODEL PREDICTIVE CONTROL FOR PHOTOVOLTAIC STATION MAXIMUM POWER POINT TRACKING SYSTEM

Directory of Open Access Journals (Sweden)

I. Elzein

2015-01-01

Full Text Available The purpose of this paper is to present an alternative maximum power point tracking, MPPT, algorithm for a photovoltaic module, PVM, to produce the maximum power, Pmax, using the optimal duty ratio, D, for different types of converters and load matching.We present a state-based approach to the design of the maximum power point tracker for a stand-alone photovoltaic power generation system. The system under consideration consists of a solar array with nonlinear time-varying characteristics, a step-up converter with appropriate filter.The proposed algorithm has the advantages of maximizing the efficiency of the power utilization, can be integrated to other MPPT algorithms without affecting the PVM performance, is excellent for Real-Time applications and is a robust analytical method, different from the traditional MPPT algorithms which are more based on trial and error, or comparisons between present and past states. The procedure to calculate the optimal duty ratio for a buck, boost and buck-boost converters, to transfer the maximum power from a PVM to a load, is presented in the paper. Additionally, the existence and uniqueness of optimal internal impedance, to transfer the maximum power from a photovoltaic module using load matching, is proved.

On the quirks of maximum parsimony and likelihood on phylogenetic networks.

Science.gov (United States)

Bryant, Christopher; Fischer, Mareike; Linz, Simone; Semple, Charles

2017-03-21

Maximum parsimony is one of the most frequently-discussed tree reconstruction methods in phylogenetic estimation. However, in recent years it has become more and more apparent that phylogenetic trees are often not sufficient to describe evolution accurately. For instance, processes like hybridization or lateral gene transfer that are commonplace in many groups of organisms and result in mosaic patterns of relationships cannot be represented by a single phylogenetic tree. This is why phylogenetic networks, which can display such events, are becoming of more and more interest in phylogenetic research. It is therefore necessary to extend concepts like maximum parsimony from phylogenetic trees to networks. Several suggestions for possible extensions can be found in recent literature, for instance the softwired and the hardwired parsimony concepts. In this paper, we analyze the so-called big parsimony problem under these two concepts, i.e. we investigate maximum parsimonious networks and analyze their properties. In particular, we show that finding a softwired maximum parsimony network is possible in polynomial time. We also show that the set of maximum parsimony networks for the hardwired definition always contains at least one phylogenetic tree. Lastly, we investigate some parallels of parsimony to different likelihood concepts on phylogenetic networks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Maximum Likelihood and Restricted Likelihood Solutions in Multiple-Method Studies.

Science.gov (United States)

Rukhin, Andrew L

2011-01-01

A formulation of the problem of combining data from several sources is discussed in terms of random effects models. The unknown measurement precision is assumed not to be the same for all methods. We investigate maximum likelihood solutions in this model. By representing the likelihood equations as simultaneous polynomial equations, the exact form of the Groebner basis for their stationary points is derived when there are two methods. A parametrization of these solutions which allows their comparison is suggested. A numerical method for solving likelihood equations is outlined, and an alternative to the maximum likelihood method, the restricted maximum likelihood, is studied. In the situation when methods variances are considered to be known an upper bound on the between-method variance is obtained. The relationship between likelihood equations and moment-type equations is also discussed.

A Bayes-Maximum Entropy method for multi-sensor data fusion

Energy Technology Data Exchange (ETDEWEB)

Beckerman, M.

1991-01-01

In this paper we introduce a Bayes-Maximum Entropy formalism for multi-sensor data fusion, and present an application of this methodology to the fusion of ultrasound and visual sensor data as acquired by a mobile robot. In our approach the principle of maximum entropy is applied to the construction of priors and likelihoods from the data. Distances between ultrasound and visual points of interest in a dual representation are used to define Gibbs likelihood distributions. Both one- and two-dimensional likelihoods are presented, and cast into a form which makes explicit their dependence upon the mean. The Bayesian posterior distributions are used to test a null hypothesis, and Maximum Entropy Maps used for navigation are updated using the resulting information from the dual representation. 14 refs., 9 figs.

Functional Maximum Autocorrelation Factors

DEFF Research Database (Denmark)

Larsen, Rasmus; Nielsen, Allan Aasbjerg

2005-01-01

MAF outperforms the functional PCA in concentrating the interesting' spectra/shape variation in one end of the eigenvalue spectrum and allows for easier interpretation of effects. Conclusions. Functional MAF analysis is a useful methods for extracting low dimensional models of temporally or spatially......Purpose. We aim at data where samples of an underlying function are observed in a spatial or temporal layout. Examples of underlying functions are reflectance spectra and biological shapes. We apply functional models based on smoothing splines and generalize the functional PCA in......\\verb+~+\\$\\backslash\\$cite{ramsay97} to functional maximum autocorrelation factors (MAF)\\verb+~+\\$\\backslash\\$cite{switzer85,larsen2001d}. We apply the method to biological shapes as well as reflectance spectra. {\\$\\backslash\\$bf Methods}. MAF seeks linear combination of the original variables that maximize autocorrelation between...

Microbiological Quality of Panicum maximum Grass Silage with Addition of Lactobacillus sp. as Starter

Science.gov (United States)

Sumarsih, S.; Sulistiyanto, B.; Utama, C. S.

2018-02-01

The aim of the research was to evaluate microbiological quality of Panicum maximum grass silage with addition Lactobacillus sp as starter. The completely randomized design was been used on this research with 4 treaments and 3 replications. The treatments were P0 ( Panicum maximum grass silage without addition Lactobacillus sp ), P1 ( Panicum maximum grass silage with 2% addition Lactobacillus sp), P2 (Panicum maximum grass silage with 4% addition Lactobacillus sp) and P3 (Panicum maximum grass silage with 6% addition Lactobacillus sp).The parameters were microbial populations of Panicum maximum grass silage (total lactic acid bacteria, total bacteria, total fungi, and Coliform bacteria. The data obtained were analyzed variance (ANOVA) and further tests performed Duncan’s Multiple Areas. The population of lactic acid bacteria was higher (PMicrobiological quality of Panicum maximum grass silage with addition Lactobacillus sp was better than no addition Lactobacillus sp.

Estimating Rhododendron maximum L. (Ericaceae) Canopy Cover Using GPS/GIS Technology

Science.gov (United States)

Tyler J. Tran; Katherine J. Elliott

2012-01-01

In the southern Appalachians, Rhododendron maximum L. (Ericaceae) is a key evergreen understory species, often forming a subcanopy in forest stands. Little is known about the significance of R. maximum cover in relation to other forest structural variables. Only recently have studies used Global Positioning System (GPS) technology...

Hierarchically porous LaFeO3 perovskite prepared from the pomelo peel bio-template for catalytic oxidation of NO

Science.gov (United States)

Zhao, Shaojun; Wang, Li; Wang, Ying; Li, Xing

2018-05-01

In this paper, pomelo peel was used as biological template to obtain hierarchically porous LaFeO3 perovskite for the catalytic oxidation of NO to NO2. In addition, X-ray diffraction (XRD), scanning electron microscopy (SEM), N2 adsorption-desorption analyses, X-ray photoelectron spectra (XPS), NO temperature-programmed desorption (NO-TPD), oxygen temperature-programmed desorption (O2-TPD) and hydrogen temperature-programmed reduction (H2-TPR) were used to investigate the micro-structure and the redox properties of the hierarchically porous LaFeO3 perovskite prepared from pomelo peel biological template and the LaFeO3 perovskite without the biological template. The results indicated that the hierarchically porous LaFeO3 perovskite successfully replicated the porous structure of pomelo peel with high specific surface area. Compared to the LaFeO3 perovskite prepared without the pomelo peel template, the hierarchically porous LaFeO3 perovskite showed better catalytic oxidization of NO to NO2 under the same conditions. The maximum NO conversions for LaFeO3 prepared with and without template were 90% at 305 °C and 76% at 313 °C, respectively. This is mainly attributed to the higher ratio of Fe4+/Fe3+, the hierarchically porous structure with more adsorbed oxygen species and higher surface area for the hierarchically porous LaFeO3 perovskite compared with the sample prepared without the pomelo peel template.

Coupling catalytic hydrolysis and oxidation on Mn/TiO2-Al2O3 for HCN removal

Science.gov (United States)

Wang, Langlang; Wang, Xueqian; Cheng, Jinhuan; Ning, Ping; Lin, Yilong

2018-05-01

The manganese-modified titania-alumina (Mn/TiO2-Al2O3) catalyst synthesized by sol-gol method was used to remove hydrogen cyanide (HCN) from simulated flue gas. Further, effects of the mass ratios of Ti/Al, Mn loading, calcination temperature, and relative humidity on HCN conversion efficiency and catalytic activity were systematically investigated. The results indicated that the Mn/TiO2-Al2O3 catalyst exhibited significantly enhanced HCN removal efficiency, and the maximum yield of N2 increased to 68.02% without the participation of water vapor. When water vapor was added into the flue gas, the yield of N2 decreased and the formation of NOx was also inhibited. The XRD and XPS results indicated that Mn was mainly present in the form of Mn2+, Mn3+, and Mn4+ on the surface of catalyst and chemisorbed oxygen played a major role in the HCN catalytic oxidation process. The results of DSC-TGA analysis and H2-TPR indicated that the catalyst also exhibited a good thermal and chemical stability. NH3-TPD and CO2-TPD indicated that the surface of the catalyst mainly contained acidic sites. During the reaction, part of NH3 was adsorbed by Brönsted and Lewis acid sites. NH3 adsorbed on Lewis acid sites participated in NH3-SCR, which reduced the amount of NOx produced and resulted in a high N2 yield.

5 CFR 581.402 - Maximum garnishment limitations.

Science.gov (United States)

2010-01-01

... PROCESSING GARNISHMENT ORDERS FOR CHILD SUPPORT AND/OR ALIMONY Consumer Credit Protection Act Restrictions..., pursuant to section 1673(b)(2) (A) and (B) of title 15 of the United States Code (the Consumer Credit... local law, the maximum part of the aggregate disposable earnings subject to garnishment to enforce any...

Finite mixture model: A maximum likelihood estimation approach on time series data

Science.gov (United States)

Yen, Phoong Seuk; Ismail, Mohd Tahir; Hamzah, Firdaus Mohamad

2014-09-01

Recently, statistician emphasized on the fitting of finite mixture model by using maximum likelihood estimation as it provides asymptotic properties. In addition, it shows consistency properties as the sample sizes increases to infinity. This illustrated that maximum likelihood estimation is an unbiased estimator. Moreover, the estimate parameters obtained from the application of maximum likelihood estimation have smallest variance as compared to others statistical method as the sample sizes increases. Thus, maximum likelihood estimation is adopted in this paper to fit the two-component mixture model in order to explore the relationship between rubber price and exchange rate for Malaysia, Thailand, Philippines and Indonesia. Results described that there is a negative effect among rubber price and exchange rate for all selected countries.

Mid-depth temperature maximum in an estuarine lake

Science.gov (United States)

Stepanenko, V. M.; Repina, I. A.; Artamonov, A. Yu; Gorin, S. L.; Lykossov, V. N.; Kulyamin, D. V.

2018-03-01

The mid-depth temperature maximum (TeM) was measured in an estuarine Bol’shoi Vilyui Lake (Kamchatka peninsula, Russia) in summer 2015. We applied 1D k-ɛ model LAKE to the case, and found it successfully simulating the phenomenon. We argue that the main prerequisite for mid-depth TeM development is a salinity increase below the freshwater mixed layer, sharp enough in order to increase the temperature with depth not to cause convective mixing and double diffusion there. Given that this condition is satisfied, the TeM magnitude is controlled by physical factors which we identified as: radiation absorption below the mixed layer, mixed-layer temperature dynamics, vertical heat conduction and water-sediments heat exchange. In addition to these, we formulate the mechanism of temperature maximum ‘pumping’, resulting from the phase shift between diurnal cycles of mixed-layer depth and temperature maximum magnitude. Based on the LAKE model results we quantify the contribution of the above listed mechanisms and find their individual significance highly sensitive to water turbidity. Relying on physical mechanisms identified we define environmental conditions favouring the summertime TeM development in salinity-stratified lakes as: small-mixed layer depth (roughly, ~wind and cloudless weather. We exemplify the effect of mixed-layer depth on TeM by a set of selected lakes.

Computing the Maximum Detour of a Plane Graph in Subquadratic Time

DEFF Research Database (Denmark)

Wulff-Nilsen, Christian

Let G be a plane graph where each edge is a line segment. We consider the problem of computing the maximum detour of G, defined as the maximum over all pairs of distinct points p and q of G of the ratio between the distance between p and q in G and the distance |pq|. The fastest known algorithm f...... for this problem has O(n^2) running time. We show how to obtain O(n^{3/2}*(log n)^3) expected running time. We also show that if G has bounded treewidth, its maximum detour can be computed in O(n*(log n)^3) expected time....

Modeling of Maximum Power Point Tracking Controller for Solar Power System

Directory of Open Access Journals (Sweden)

Aryuanto Soetedjo

2012-09-01

Full Text Available In this paper, a Maximum Power Point Tracking (MPPT controller for solar power system is modeled using MATLAB Simulink. The model consists of PV module, buck converter, and MPPT controller. The contribution of the work is in the modeling of buck converter that allowing the input voltage of the converter, i.e. output voltage of PV is changed by varying the duty cycle, so that the maximum power point could be tracked when the environmental changes. The simulation results show that the developed model performs well in tracking the maximum power point (MPP of the PV module using Perturb and Observe (P&O Algorithm.

Accurate Maximum Power Tracking in Photovoltaic Systems Affected by Partial Shading

Directory of Open Access Journals (Sweden)

Pierluigi Guerriero

2015-01-01

Full Text Available A maximum power tracking algorithm exploiting operating point information gained on individual solar panels is presented. The proposed algorithm recognizes the presence of multiple local maxima in the power voltage curve of a shaded solar field and evaluates the coordinated of the absolute maximum. The effectiveness of the proposed approach is evidenced by means of circuit level simulation and experimental results. Experiments evidenced that, in comparison with a standard perturb and observe algorithm, we achieve faster convergence in normal operating conditions (when the solar field is uniformly illuminated and we accurately locate the absolute maximum power point in partial shading conditions, thus avoiding the convergence on local maxima.

Discontinuity of maximum entropy inference and quantum phase transitions

International Nuclear Information System (INIS)

Chen, Jianxin; Ji, Zhengfeng; Yu, Nengkun; Zeng, Bei; Li, Chi-Kwong; Poon, Yiu-Tung; Shen, Yi; Zhou, Duanlu

2015-01-01

In this paper, we discuss the connection between two genuinely quantum phenomena—the discontinuity of quantum maximum entropy inference and quantum phase transitions at zero temperature. It is shown that the discontinuity of the maximum entropy inference of local observable measurements signals the non-local type of transitions, where local density matrices of the ground state change smoothly at the transition point. We then propose to use the quantum conditional mutual information of the ground state as an indicator to detect the discontinuity and the non-local type of quantum phase transitions in the thermodynamic limit. (paper)

38 CFR 36.4204 - Loan purposes, maximum loan amounts and terms.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Loan purposes, maximum loan amounts and terms. 36.4204 Section 36.4204 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF... constructing a suitable pad for the manufactured home. (e) The maximum permissible loan terms shall not exceed...

Unification of field theory and maximum entropy methods for learning probability densities

Science.gov (United States)

Kinney, Justin B.

2015-09-01

The need to estimate smooth probability distributions (a.k.a. probability densities) from finite sampled data is ubiquitous in science. Many approaches to this problem have been described, but none is yet regarded as providing a definitive solution. Maximum entropy estimation and Bayesian field theory are two such approaches. Both have origins in statistical physics, but the relationship between them has remained unclear. Here I unify these two methods by showing that every maximum entropy density estimate can be recovered in the infinite smoothness limit of an appropriate Bayesian field theory. I also show that Bayesian field theory estimation can be performed without imposing any boundary conditions on candidate densities, and that the infinite smoothness limit of these theories recovers the most common types of maximum entropy estimates. Bayesian field theory thus provides a natural test of the maximum entropy null hypothesis and, furthermore, returns an alternative (lower entropy) density estimate when the maximum entropy hypothesis is falsified. The computations necessary for this approach can be performed rapidly for one-dimensional data, and software for doing this is provided.

Unification of field theory and maximum entropy methods for learning probability densities.

Science.gov (United States)

Kinney, Justin B

2015-09-01

The need to estimate smooth probability distributions (a.k.a. probability densities) from finite sampled data is ubiquitous in science. Many approaches to this problem have been described, but none is yet regarded as providing a definitive solution. Maximum entropy estimation and Bayesian field theory are two such approaches. Both have origins in statistical physics, but the relationship between them has remained unclear. Here I unify these two methods by showing that every maximum entropy density estimate can be recovered in the infinite smoothness limit of an appropriate Bayesian field theory. I also show that Bayesian field theory estimation can be performed without imposing any boundary conditions on candidate densities, and that the infinite smoothness limit of these theories recovers the most common types of maximum entropy estimates. Bayesian field theory thus provides a natural test of the maximum entropy null hypothesis and, furthermore, returns an alternative (lower entropy) density estimate when the maximum entropy hypothesis is falsified. The computations necessary for this approach can be performed rapidly for one-dimensional data, and software for doing this is provided.

Design of Asymmetrical Relay Resonators for Maximum Efficiency of Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Bo-Hee Choi

2016-01-01

Full Text Available This paper presents a new design method of asymmetrical relay resonators for maximum wireless power transfer. A new design method for relay resonators is demanded because maximum power transfer efficiency (PTE is not obtained at the resonant frequency of unit resonator. The maximum PTE for relay resonators is obtained at the different resonances of unit resonator. The optimum design of asymmetrical relay is conducted by both the optimum placement and the optimum capacitance of resonators. The optimum placement is found by scanning the positions of the relays and optimum capacitance can be found by using genetic algorithm (GA. The PTEs are enhanced when capacitance is optimally designed by GA according to the position of relays, respectively, and then maximum efficiency is obtained at the optimum placement of relays. The capacitance of the second resonator to nth resonator and the load resistance should be determined for maximum efficiency while the capacitance of the first resonator and the source resistance are obtained for the impedance matching. The simulated and measured results are in good agreement.

A practical exact maximum compatibility algorithm for reconstruction of recent evolutionary history.

Science.gov (United States)

Cherry, Joshua L

2017-02-23

Maximum compatibility is a method of phylogenetic reconstruction that is seldom applied to molecular sequences. It may be ideal for certain applications, such as reconstructing phylogenies of closely-related bacteria on the basis of whole-genome sequencing. Here I present an algorithm that rapidly computes phylogenies according to a compatibility criterion. Although based on solutions to the maximum clique problem, this algorithm deals properly with ambiguities in the data. The algorithm is applied to bacterial data sets containing up to nearly 2000 genomes with several thousand variable nucleotide sites. Run times are several seconds or less. Computational experiments show that maximum compatibility is less sensitive than maximum parsimony to the inclusion of nucleotide data that, though derived from actual sequence reads, has been identified as likely to be misleading. Maximum compatibility is a useful tool for certain phylogenetic problems, such as inferring the relationships among closely-related bacteria from whole-genome sequence data. The algorithm presented here rapidly solves fairly large problems of this type, and provides robustness against misleading characters than can pollute large-scale sequencing data.

ON THE MAXIMUM MASS OF STELLAR BLACK HOLES

International Nuclear Information System (INIS)

Belczynski, Krzysztof; Fryer, Chris L.; Bulik, Tomasz; Ruiter, Ashley; Valsecchi, Francesca; Vink, Jorick S.; Hurley, Jarrod R.

2010-01-01

We present the spectrum of compact object masses: neutron stars and black holes (BHs) that originate from single stars in different environments. In particular, we calculate the dependence of maximum BH mass on metallicity and on some specific wind mass loss rates (e.g., Hurley et al. and Vink et al.). Our calculations show that the highest mass BHs observed in the Galaxy M bh ∼ 15 M sun in the high metallicity environment (Z = Z sun = 0.02) can be explained with stellar models and the wind mass loss rates adopted here. To reach this result we had to set luminous blue variable mass loss rates at the level of ∼10 -4 M sun yr -1 and to employ metallicity-dependent Wolf-Rayet winds. With such winds, calibrated on Galactic BH mass measurements, the maximum BH mass obtained for moderate metallicity (Z = 0.3 Z sun = 0.006) is M bh,max = 30 M sun . This is a rather striking finding as the mass of the most massive known stellar BH is M bh = 23-34 M sun and, in fact, it is located in a small star-forming galaxy with moderate metallicity. We find that in the very low (globular cluster-like) metallicity environment the maximum BH mass can be as high as M bh,max = 80 M sun (Z = 0.01 Z sun = 0.0002). It is interesting to note that X-ray luminosity from Eddington-limited accretion onto an 80 M sun BH is of the order of ∼10 40 erg s -1 and is comparable to luminosities of some known ultra-luminous X-ray sources. We emphasize that our results were obtained for single stars only and that binary interactions may alter these maximum BH masses (e.g., accretion from a close companion). This is strictly a proof-of-principle study which demonstrates that stellar models can naturally explain even the most massive known stellar BHs.

A Hybrid Maximum Power Point Tracking Method for Automobile Exhaust Thermoelectric Generator

Science.gov (United States)

Quan, Rui; Zhou, Wei; Yang, Guangyou; Quan, Shuhai

2017-05-01

To make full use of the maximum output power of automobile exhaust thermoelectric generator (AETEG) based on Bi2Te3 thermoelectric modules (TEMs), taking into account the advantages and disadvantages of existing maximum power point tracking methods, and according to the output characteristics of TEMs, a hybrid maximum power point tracking method combining perturb and observe (P&O) algorithm, quadratic interpolation and constant voltage tracking method was put forward in this paper. Firstly, it searched the maximum power point with P&O algorithms and a quadratic interpolation method, then, it forced the AETEG to work at its maximum power point with constant voltage tracking. A synchronous buck converter and controller were implemented in the electric bus of the AETEG applied in a military sports utility vehicle, and the whole system was modeled and simulated with a MATLAB/Simulink environment. Simulation results demonstrate that the maximum output power of the AETEG based on the proposed hybrid method is increased by about 3.0% and 3.7% compared with that using only the P&O algorithm and the quadratic interpolation method, respectively. The shorter tracking time is only 1.4 s, which is reduced by half compared with that of the P&O algorithm and quadratic interpolation method, respectively. The experimental results demonstrate that the tracked maximum power is approximately equal to the real value using the proposed hybrid method,and it can preferentially deal with the voltage fluctuation of the AETEG with only P&O algorithm, and resolve the issue that its working point can barely be adjusted only with constant voltage tracking when the operation conditions change.

47 CFR 1.1507 - Rulemaking on maximum rates for attorney fees.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Rulemaking on maximum rates for attorney fees... § 1.1507 Rulemaking on maximum rates for attorney fees. (a) If warranted by an increase in the cost of... types of proceedings), the Commission may adopt regulations providing that attorney fees may be awarded...

The maximum entropy production and maximum Shannon information entropy in enzyme kinetics

Science.gov (United States)

Dobovišek, Andrej; Markovič, Rene; Brumen, Milan; Fajmut, Aleš

2018-04-01

We demonstrate that the maximum entropy production principle (MEPP) serves as a physical selection principle for the description of the most probable non-equilibrium steady states in simple enzymatic reactions. A theoretical approach is developed, which enables maximization of the density of entropy production with respect to the enzyme rate constants for the enzyme reaction in a steady state. Mass and Gibbs free energy conservations are considered as optimization constraints. In such a way computed optimal enzyme rate constants in a steady state yield also the most uniform probability distribution of the enzyme states. This accounts for the maximal Shannon information entropy. By means of the stability analysis it is also demonstrated that maximal density of entropy production in that enzyme reaction requires flexible enzyme structure, which enables rapid transitions between different enzyme states. These results are supported by an example, in which density of entropy production and Shannon information entropy are numerically maximized for the enzyme Glucose Isomerase.

Deep Learning for Prediction of Obstructive Disease From Fast Myocardial Perfusion SPECT: A Multicenter Study.

Science.gov (United States)

Betancur, Julian; Commandeur, Frederic; Motlagh, Mahsaw; Sharir, Tali; Einstein, Andrew J; Bokhari, Sabahat; Fish, Mathews B; Ruddy, Terrence D; Kaufmann, Philipp; Sinusas, Albert J; Miller, Edward J; Bateman, Timothy M; Dorbala, Sharmila; Di Carli, Marcelo; Germano, Guido; Otaki, Yuka; Tamarappoo, Balaji K; Dey, Damini; Berman, Daniel S; Slomka, Piotr J

2018-03-12

The study evaluated the automatic prediction of obstructive disease from myocardial perfusion imaging (MPI) by deep learning as compared with total perfusion deficit (TPD). Deep convolutional neural networks trained with a large multicenter population may provide improved prediction of per-patient and per-vessel coronary artery disease from single-photon emission computed tomography MPI. A total of 1,638 patients (67% men) without known coronary artery disease, undergoing stress 99m Tc-sestamibi or tetrofosmin MPI with new generation solid-state scanners in 9 different sites, with invasive coronary angiography performed within 6 months of MPI, were studied. Obstructive disease was defined as ≥70% narrowing of coronary arteries (≥50% for left main artery). Left ventricular myocardium was segmented using clinical nuclear cardiology software and verified by an expert reader. Stress TPD was computed using sex- and camera-specific normal limits. Deep learning was trained using raw and quantitative polar maps and evaluated for prediction of obstructive stenosis in a stratified 10-fold cross-validation procedure. A total of 1,018 (62%) patients and 1,797 of 4,914 (37%) arteries had obstructive disease. Area under the receiver-operating characteristic curve for disease prediction by deep learning was higher than for TPD (per patient: 0.80 vs. 0.78; per vessel: 0.76 vs. 0.73: p deep learning threshold set to the same specificity as TPD, per-patient sensitivity improved from 79.8% (TPD) to 82.3% (deep learning) (p deep learning) (p Deep learning has the potential to improve automatic interpretation of MPI as compared with current clinical methods. Copyright © 2018 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

A Hybrid Maximum Power Point Search Method Using Temperature Measurements in Partial Shading Conditions

Directory of Open Access Journals (Sweden)

Mroczka Janusz

2014-12-01

Full Text Available Photovoltaic panels have a non-linear current-voltage characteristics to produce the maximum power at only one point called the maximum power point. In the case of the uniform illumination a single solar panel shows only one maximum power, which is also the global maximum power point. In the case an irregularly illuminated photovoltaic panel many local maxima on the power-voltage curve can be observed and only one of them is the global maximum. The proposed algorithm detects whether a solar panel is in the uniform insolation conditions. Then an appropriate strategy of tracking the maximum power point is taken using a decision algorithm. The proposed method is simulated in the environment created by the authors, which allows to stimulate photovoltaic panels in real conditions of lighting, temperature and shading.

Maximum neutron flux in thermal reactors; Maksimum neutronskog fluksa kod termalnih reaktora

Energy Technology Data Exchange (ETDEWEB)

Strugar, P V [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

1968-07-01

Direct approach to the problem is to calculate spatial distribution of fuel concentration if the reactor core directly using the condition of maximum neutron flux and comply with thermal limitations. This paper proved that the problem can be solved by applying the variational calculus, i.e. by using the maximum principle of Pontryagin. Mathematical model of reactor core is based on the two-group neutron diffusion theory with some simplifications which make it appropriate from maximum principle point of view. Here applied theory of maximum principle are suitable for application. The solution of optimum distribution of fuel concentration in the reactor core is obtained in explicit analytical form. The reactor critical dimensions are roots of a system of nonlinear equations and verification of optimum conditions can be done only for specific examples.

Growth and maximum size of tiger sharks (Galeocerdo cuvier) in Hawaii.

Science.gov (United States)

Meyer, Carl G; O'Malley, Joseph M; Papastamatiou, Yannis P; Dale, Jonathan J; Hutchinson, Melanie R; Anderson, James M; Royer, Mark A; Holland, Kim N

2014-01-01

Tiger sharks (Galecerdo cuvier) are apex predators characterized by their broad diet, large size and rapid growth. Tiger shark maximum size is typically between 380 & 450 cm Total Length (TL), with a few individuals reaching 550 cm TL, but the maximum size of tiger sharks in Hawaii waters remains uncertain. A previous study suggested tiger sharks grow rather slowly in Hawaii compared to other regions, but this may have been an artifact of the method used to estimate growth (unvalidated vertebral ring counts) compounded by small sample size and narrow size range. Since 1993, the University of Hawaii has conducted a research program aimed at elucidating tiger shark biology, and to date 420 tiger sharks have been tagged and 50 recaptured. All recaptures were from Hawaii except a single shark recaptured off Isla Jacques Cousteau (24°13'17″N 109°52'14″W), in the southern Gulf of California (minimum distance between tag and recapture sites  =  approximately 5,000 km), after 366 days at liberty (DAL). We used these empirical mark-recapture data to estimate growth rates and maximum size for tiger sharks in Hawaii. We found that tiger sharks in Hawaii grow twice as fast as previously thought, on average reaching 340 cm TL by age 5, and attaining a maximum size of 403 cm TL. Our model indicates the fastest growing individuals attain 400 cm TL by age 5, and the largest reach a maximum size of 444 cm TL. The largest shark captured during our study was 464 cm TL but individuals >450 cm TL were extremely rare (0.005% of sharks captured). We conclude that tiger shark growth rates and maximum sizes in Hawaii are generally consistent with those in other regions, and hypothesize that a broad diet may help them to achieve this rapid growth by maximizing prey consumption rates.

An investigation of rugby scrimmaging posture and individual maximum pushing force.

Science.gov (United States)

Wu, Wen-Lan; Chang, Jyh-Jong; Wu, Jia-Hroung; Guo, Lan-Yuen

2007-02-01

Although rugby is a popular contact sport and the isokinetic muscle torque assessment has recently found widespread application in the field of sports medicine, little research has examined the factors associated with the performance of game-specific skills directly by using the isokinetic-type rugby scrimmaging machine. This study is designed to (a) measure and observe the differences in the maximum individual pushing forward force produced by scrimmaging in different body postures (3 body heights x 2 foot positions) with a self-developed rugby scrimmaging machine and (b) observe the variations in hip, knee, and ankle angles at different body postures and explore the relationship between these angle values and the individual maximum pushing force. Ten national rugby players were invited to participate in the examination. The experimental equipment included a self-developed rugby scrimmaging machine and a 3-dimensional motion analysis system. Our results showed that the foot positions (parallel and nonparallel foot positions) do not affect the maximum pushing force; however, the maximum pushing force was significantly lower in posture I (36% body height) than in posture II (38%) and posture III (40%). The maximum forward force in posture III (40% body height) was also slightly greater than for the scrum in posture II (38% body height). In addition, it was determined that hip, knee, and ankle angles under parallel feet positioning are factors that are closely negatively related in terms of affecting maximum pushing force in scrimmaging. In cross-feet postures, there was a positive correlation between individual forward force and hip angle of the rear leg. From our results, we can conclude that if the player stands in an appropriate starting position at the early stage of scrimmaging, it will benefit the forward force production.

Maximum Likelihood Blind Channel Estimation for Space-Time Coding Systems

Directory of Open Access Journals (Sweden)

Hakan A. Çırpan

2002-05-01

Full Text Available Sophisticated signal processing techniques have to be developed for capacity enhancement of future wireless communication systems. In recent years, space-time coding is proposed to provide significant capacity gains over the traditional communication systems in fading wireless channels. Space-time codes are obtained by combining channel coding, modulation, transmit diversity, and optional receive diversity in order to provide diversity at the receiver and coding gain without sacrificing the bandwidth. In this paper, we consider the problem of blind estimation of space-time coded signals along with the channel parameters. Both conditional and unconditional maximum likelihood approaches are developed and iterative solutions are proposed. The conditional maximum likelihood algorithm is based on iterative least squares with projection whereas the unconditional maximum likelihood approach is developed by means of finite state Markov process modelling. The performance analysis issues of the proposed methods are studied. Finally, some simulation results are presented.

Beat the Deviations in Estimating Maximum Power of Thermoelectric Modules

DEFF Research Database (Denmark)

Gao, Junling; Chen, Min

2013-01-01

Under a certain temperature difference, the maximum power of a thermoelectric module can be estimated by the open-circuit voltage and the short-circuit current. In practical measurement, there exist two switch modes, either from open to short or from short to open, but the two modes can give...... different estimations on the maximum power. Using TEG-127-2.8-3.5-250 and TEG-127-1.4-1.6-250 as two examples, the difference is about 10%, leading to some deviations with the temperature change. This paper analyzes such differences by means of a nonlinear numerical model of thermoelectricity, and finds out...... that the main cause is the influence of various currents on the produced electromotive potential. A simple and effective calibration method is proposed to minimize the deviations in specifying the maximum power. Experimental results validate the method with improved estimation accuracy....

MPBoot: fast phylogenetic maximum parsimony tree inference and bootstrap approximation.

Science.gov (United States)

Hoang, Diep Thi; Vinh, Le Sy; Flouri, Tomáš; Stamatakis, Alexandros; von Haeseler, Arndt; Minh, Bui Quang

2018-02-02

The nonparametric bootstrap is widely used to measure the branch support of phylogenetic trees. However, bootstrapping is computationally expensive and remains a bottleneck in phylogenetic analyses. Recently, an ultrafast bootstrap approximation (UFBoot) approach was proposed for maximum likelihood analyses. However, such an approach is still missing for maximum parsimony. To close this gap we present MPBoot, an adaptation and extension of UFBoot to compute branch supports under the maximum parsimony principle. MPBoot works for both uniform and non-uniform cost matrices. Our analyses on biological DNA and protein showed that under uniform cost matrices, MPBoot runs on average 4.7 (DNA) to 7 times (protein data) (range: 1.2-20.7) faster than the standard parsimony bootstrap implemented in PAUP*; but 1.6 (DNA) to 4.1 times (protein data) slower than the standard bootstrap with a fast search routine in TNT (fast-TNT). However, for non-uniform cost matrices MPBoot is 5 (DNA) to 13 times (protein data) (range:0.3-63.9) faster than fast-TNT. We note that MPBoot achieves better scores more frequently than PAUP* and fast-TNT. However, this effect is less pronounced if an intensive but slower search in TNT is invoked. Moreover, experiments on large-scale simulated data show that while both PAUP* and TNT bootstrap estimates are too conservative, MPBoot bootstrap estimates appear more unbiased. MPBoot provides an efficient alternative to the standard maximum parsimony bootstrap procedure. It shows favorable performance in terms of run time, the capability of finding a maximum parsimony tree, and high bootstrap accuracy on simulated as well as empirical data sets. MPBoot is easy-to-use, open-source and available at http://www.cibiv.at/software/mpboot .

Efficient heuristics for maximum common substructure search.

Science.gov (United States)

Englert, Péter; Kovács, Péter

2015-05-26

Maximum common substructure search is a computationally hard optimization problem with diverse applications in the field of cheminformatics, including similarity search, lead optimization, molecule alignment, and clustering. Most of these applications have strict constraints on running time, so heuristic methods are often preferred. However, the development of an algorithm that is both fast enough and accurate enough for most practical purposes is still a challenge. Moreover, in some applications, the quality of a common substructure depends not only on its size but also on various topological features of the one-to-one atom correspondence it defines. Two state-of-the-art heuristic algorithms for finding maximum common substructures have been implemented at ChemAxon Ltd., and effective heuristics have been developed to improve both their efficiency and the relevance of the atom mappings they provide. The implementations have been thoroughly evaluated and compared with existing solutions (KCOMBU and Indigo). The heuristics have been found to greatly improve the performance and applicability of the algorithms. The purpose of this paper is to introduce the applied methods and present the experimental results.

On minimizing the maximum broadcast decoding delay for instantly decodable network coding

KAUST Repository

Douik, Ahmed S.; Sorour, Sameh; Alouini, Mohamed-Slim; Ai-Naffouri, Tareq Y.

2014-01-01

In this paper, we consider the problem of minimizing the maximum broadcast decoding delay experienced by all the receivers of generalized instantly decodable network coding (IDNC). Unlike the sum decoding delay, the maximum decoding delay as a

Computing the Maximum Detour of a Plane Graph in Subquadratic Time

DEFF Research Database (Denmark)

Wulff-Nilsen, Christian

2008-01-01

Let G be a plane graph where each edge is a line segment. We consider the problem of computing the maximum detour of G, defined as the maximum over all pairs of distinct points p and q of G of the ratio between the distance between p and q in G and the distance |pq|. The fastest known algorithm...

Promotion Effect of CaO Modification on Mesoporous Al2O3-Supported Ni Catalysts for CO2 Methanation

Directory of Open Access Journals (Sweden)

Wen Yang

2016-01-01

Full Text Available The catalysts Ni/Al2O3 and CaO modified Ni/Al2O3 were prepared by impregnation method and applied for methanation of CO2. The catalysts were characterized by N2 adsorption/desorption, temperature-programmed reduction of H2 (H2-TPR, X-ray diffraction (XRD, and temperature-programmed desorption of CO2 and H2 (CO2-TPD and H2-TPD techniques, respectively. TPR and XRD results indicated that CaO can effectively restrain the growth of NiO nanoparticles, improve the dispersion of NiO, and weaken the interaction between NiO and Al2O3. CO2-TPD and H2-TPD results suggested that CaO can change the environment surrounding of CO2 and H2 adsorption and thus the reactants on the Ni atoms can be activated more easily. The modified Ni/Al2O3 showed better catalytic activity than pure Ni/Al2O3. Ni/CaO-Al2O3 showed high CO2 conversion especially at low temperatures compared to Ni/Al2O3, and the selectivity to CH4 was very close to 1. The high CO2 conversion over Ni/CaO-Al2O3 was mainly caused by the surface coverage by CO2-derived species on CaO-Al2O3 surface.

Hydrogenation of Phenylacetylene to Styrene on Pre-C{sub x}H{sub y}- and C-Covered Cu(111) Single Crystal Catalysts

Energy Technology Data Exchange (ETDEWEB)

Sohn, Young Ku [Yeungnam University, Gyeongsan (Korea, Republic of); Wei, Wei; White, John M. [The University of Texas at Austin, Texas (United States)

2011-05-15

Thermal hydrogenation of phenylacetylene (PA, C{sub 8}H{sub 6}) to styrene (C{sub 8}H{sub 8}) on pre-C{sub x}H{sub y}- and C-covered Cu(111) single crystal substrates has been studied using temperature-programmed desorption (TPD) mass spectrometry. Chemisorbed PA with an acetylene group has been proved to be associated with hydrogen of pre-adsorbed C{sub x}H{sub y} to form styrene (104 amu) on Cu surface. For the parent (PA) mass (102 amu) TPD profile, the TPD peaks at 360 K and 410 K are assigned to chemisorbed vertically aligned PA and flat-lying cross-bridged PA, respectively (J. Phys. Chem. C 2007, 111, 5101). The relative I{sub 360K}/I{sub 410K} TPD ratio dramatically increases with increasing pre-adsorbed C{sub x}H{sub y} before dosing PA, while the ratio does not increase for pre-C-covered surface. For PA on pre-C{sub x}H{sub y}-covered Cu(111) surface, styrene desorption is enhanced relative to the parent PA desorption, while styrene formation is dramatically quenched on pre-C-covered (lack of adsorbed hydrogen nearby) surface. It appears that only cross-bridged PA associates with adsorbed hydrogen to form styrene that promptly desorbs at 410 K, while vertically aligned PA is less likely to participate in forming styrene.

On an Objective Basis for the Maximum Entropy Principle

Directory of Open Access Journals (Sweden)

David J. Miller

2015-01-01

Full Text Available In this letter, we elaborate on some of the issues raised by a recent paper by Neapolitan and Jiang concerning the maximum entropy (ME principle and alternative principles for estimating probabilities consistent with known, measured constraint information. We argue that the ME solution for the “problematic” example introduced by Neapolitan and Jiang has stronger objective basis, rooted in results from information theory, than their alternative proposed solution. We also raise some technical concerns about the Bayesian analysis in their work, which was used to independently support their alternative to the ME solution. The letter concludes by noting some open problems involving maximum entropy statistical inference.

Maximum Safety Regenerative Power Tracking for DC Traction Power Systems

Directory of Open Access Journals (Sweden)

Guifu Du

2017-02-01

Full Text Available Direct current (DC traction power systems are widely used in metro transport systems, with running rails usually being used as return conductors. When traction current flows through the running rails, a potential voltage known as “rail potential” is generated between the rails and ground. Currently, abnormal rises of rail potential exist in many railway lines during the operation of railway systems. Excessively high rail potentials pose a threat to human life and to devices connected to the rails. In this paper, the effect of regenerative power distribution on rail potential is analyzed. Maximum safety regenerative power tracking is proposed for the control of maximum absolute rail potential and energy consumption during the operation of DC traction power systems. The dwell time of multiple trains at each station and the trigger voltage of the regenerative energy absorbing device (READ are optimized based on an improved particle swarm optimization (PSO algorithm to manage the distribution of regenerative power. In this way, the maximum absolute rail potential and energy consumption of DC traction power systems can be reduced. The operation data of Guangzhou Metro Line 2 are used in the simulations, and the results show that the scheme can reduce the maximum absolute rail potential and energy consumption effectively and guarantee the safety in energy saving of DC traction power systems.

Maximum Mass of Hybrid Stars in the Quark Bag Model

Science.gov (United States)

Alaverdyan, G. B.; Vartanyan, Yu. L.

2017-12-01

The effect of model parameters in the equation of state for quark matter on the magnitude of the maximum mass of hybrid stars is examined. Quark matter is described in terms of the extended MIT bag model including corrections for one-gluon exchange. For nucleon matter in the range of densities corresponding to the phase transition, a relativistic equation of state is used that is calculated with two-particle correlations taken into account based on using the Bonn meson-exchange potential. The Maxwell construction is used to calculate the characteristics of the first order phase transition and it is shown that for a fixed value of the strong interaction constant αs, the baryon concentrations of the coexisting phases grow monotonically as the bag constant B increases. It is shown that for a fixed value of the strong interaction constant αs, the maximum mass of a hybrid star increases as the bag constant B decreases. For a given value of the bag parameter B, the maximum mass rises as the strong interaction constant αs increases. It is shown that the configurations of hybrid stars with maximum masses equal to or exceeding the mass of the currently known most massive pulsar are possible for values of the strong interaction constant αs > 0.6 and sufficiently low values of the bag constant.

Study of forecasting maximum demand of electric power

Energy Technology Data Exchange (ETDEWEB)

Yoo, B.C.; Hwang, Y.J. [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1997-08-01

As far as the past performances of power supply and demand in Korea is concerned, one of the striking phenomena is that there have been repeated periodic surpluses and shortages of power generation facilities. Precise assumption and prediction of power demands is the basic work in establishing a supply plan and carrying out the right policy since facilities investment of the power generation industry requires a tremendous amount of capital and a long construction period. The purpose of this study is to study a model for the inference and prediction of a more precise maximum demand under these backgrounds. The non-parametric model considered in this study, paying attention to meteorological factors such as temperature and humidity, does not have a simple proportionate relationship with the maximum power demand, but affects it through mutual complicated nonlinear interaction. I used the non-parametric inference technique by introducing meteorological effects without importing any literal assumption on the interaction of temperature and humidity preliminarily. According to the analysis result, it is found that the non-parametric model that introduces the number of tropical nights which shows the continuity of the meteorological effect has better prediction power than the linear model. The non- parametric model that considers both the number of tropical nights and the number of cooling days at the same time is a model for predicting maximum demand. 7 refs., 6 figs., 9 tabs.

Influence of Dynamic Neuromuscular Stabilization Approach on Maximum Kayak Paddling Force

Directory of Open Access Journals (Sweden)

Davidek Pavel

2018-03-01

Full Text Available The purpose of this study was to examine the effect of Dynamic Neuromuscular Stabilization (DNS exercise on maximum paddling force (PF and self-reported pain perception in the shoulder girdle area in flatwater kayakers. Twenty male flatwater kayakers from a local club (age = 21.9 ± 2.4 years, body height = 185.1 ± 7.9 cm, body mass = 83.9 ± 9.1 kg were randomly assigned to the intervention or control groups. During the 6-week study, subjects from both groups performed standard off-season training. Additionally, the intervention group engaged in a DNS-based core stabilization exercise program (quadruped exercise, side sitting exercise, sitting exercise and squat exercise after each standard training session. Using a kayak ergometer, the maximum PF stroke was measured four times during the six weeks. All subjects completed the Disabilities of the Arm, Shoulder and Hand (DASH questionnaire before and after the 6-week interval to evaluate subjective pain perception in the shoulder girdle area. Initially, no significant differences in maximum PF and the DASH questionnaire were identified between the two groups. Repeated measures analysis of variance indicated that the experimental group improved significantly compared to the control group on maximum PF (p = .004; Cohen’s d = .85, but not on the DASH questionnaire score (p = .731 during the study. Integration of DNS with traditional flatwater kayak training may significantly increase maximum PF, but may not affect pain perception to the same extent.

Determining Maximum Photovoltaic Penetration in a Distribution Grid considering Grid Operation Limits

DEFF Research Database (Denmark)

Kordheili, Reza Ahmadi; Bak-Jensen, Birgitte; Pillai, Jayakrishnan Radhakrishna

2014-01-01

High penetration of photovoltaic panels in distribution grid can bring the grid to its operation limits. The main focus of the paper is to determine maximum photovoltaic penetration level in the grid. Three main criteria were investigated for determining maximum penetration level of PV panels...... for this grid: even distribution of PV panels, aggregation of panels at the beginning of each feeder, and aggregation of panels at the end of each feeder. Load modeling is done using Velander formula. Since PV generation is highest in the summer due to irradiation, a summer day was chosen to determine maximum......; maximum voltage deviation of customers, cables current limits, and transformer nominal value. Voltage deviation of different buses was investigated for different penetration levels. The proposed model was simulated on a Danish distribution grid. Three different PV location scenarios were investigated...

Effect of current on the maximum possible reward.

Science.gov (United States)

Gallistel, C R; Leon, M; Waraczynski, M; Hanau, M S

1991-12-01

Using a 2-lever choice paradigm with concurrent variable interval schedules of reward, it was found that when pulse frequency is increased, the preference-determining rewarding effect of 0.5-s trains of brief cathodal pulses delivered to the medial forebrain bundle of the rat saturates (stops increasing) at values ranging from 200 to 631 pulses/s (pps). Raising the current lowered the saturation frequency, which confirms earlier, more extensive findings showing that the rewarding effect of short trains saturates at pulse frequencies that vary from less than 100 pps to more than 800 pps, depending on the current. It was also found that the maximum possible reward--the magnitude of the reward at or beyond the saturation pulse frequency--increases with increasing current. Thus, increasing the current reduces the saturation frequency but increases the subjective magnitude of the maximum possible reward.

Rumor Identification with Maximum Entropy in MicroNet

Directory of Open Access Journals (Sweden)

Suisheng Yu

2017-01-01

Full Text Available The widely used applications of Microblog, WeChat, and other social networking platforms (that we call MicroNet shorten the period of information dissemination and expand the range of information dissemination, which allows rumors to cause greater harm and have more influence. A hot topic in the information dissemination field is how to identify and block rumors. Based on the maximum entropy model, this paper constructs the recognition mechanism of rumor information in the micronetwork environment. First, based on the information entropy theory, we obtained the characteristics of rumor information using the maximum entropy model. Next, we optimized the original classifier training set and the feature function to divide the information into rumors and nonrumors. Finally, the experimental simulation results show that the rumor identification results using this method are better than the original classifier and other related classification methods.

Regularized maximum correntropy machine

KAUST Repository

Wang, Jim Jing-Yan; Wang, Yunji; Jing, Bing-Yi; Gao, Xin

2015-01-01

In this paper we investigate the usage of regularized correntropy framework for learning of classifiers from noisy labels. The class label predictors learned by minimizing transitional loss functions are sensitive to the noisy and outlying labels of training samples, because the transitional loss functions are equally applied to all the samples. To solve this problem, we propose to learn the class label predictors by maximizing the correntropy between the predicted labels and the true labels of the training samples, under the regularized Maximum Correntropy Criteria (MCC) framework. Moreover, we regularize the predictor parameter to control the complexity of the predictor. The learning problem is formulated by an objective function considering the parameter regularization and MCC simultaneously. By optimizing the objective function alternately, we develop a novel predictor learning algorithm. The experiments on two challenging pattern classification tasks show that it significantly outperforms the machines with transitional loss functions.

Regularized maximum correntropy machine

KAUST Repository

Wang, Jim Jing-Yan

2015-02-12

In this paper we investigate the usage of regularized correntropy framework for learning of classifiers from noisy labels. The class label predictors learned by minimizing transitional loss functions are sensitive to the noisy and outlying labels of training samples, because the transitional loss functions are equally applied to all the samples. To solve this problem, we propose to learn the class label predictors by maximizing the correntropy between the predicted labels and the true labels of the training samples, under the regularized Maximum Correntropy Criteria (MCC) framework. Moreover, we regularize the predictor parameter to control the complexity of the predictor. The learning problem is formulated by an objective function considering the parameter regularization and MCC simultaneously. By optimizing the objective function alternately, we develop a novel predictor learning algorithm. The experiments on two challenging pattern classification tasks show that it significantly outperforms the machines with transitional loss functions.

Quality, precision and accuracy of the maximum No. 40 anemometer

Energy Technology Data Exchange (ETDEWEB)

Obermeir, J. [Otech Engineering, Davis, CA (United States); Blittersdorf, D. [NRG Systems Inc., Hinesburg, VT (United States)

1996-12-31

This paper synthesizes available calibration data for the Maximum No. 40 anemometer. Despite its long history in the wind industry, controversy surrounds the choice of transfer function for this anemometer. Many users are unaware that recent changes in default transfer functions in data loggers are producing output wind speed differences as large as 7.6%. Comparison of two calibration methods used for large samples of Maximum No. 40 anemometers shows a consistent difference of 4.6% in output speeds. This difference is significantly larger than estimated uncertainty levels. Testing, initially performed to investigate related issues, reveals that Gill and Maximum cup anemometers change their calibration transfer functions significantly when calibrated in the open atmosphere compared with calibration in a laminar wind tunnel. This indicates that atmospheric turbulence changes the calibration transfer function of cup anemometers. These results call into question the suitability of standard wind tunnel calibration testing for cup anemometers. 6 refs., 10 figs., 4 tabs.

Maximum-entropy networks pattern detection, network reconstruction and graph combinatorics

CERN Document Server

Squartini, Tiziano

2017-01-01

This book is an introduction to maximum-entropy models of random graphs with given topological properties and their applications. Its original contribution is the reformulation of many seemingly different problems in the study of both real networks and graph theory within the unified framework of maximum entropy. Particular emphasis is put on the detection of structural patterns in real networks, on the reconstruction of the properties of networks from partial information, and on the enumeration and sampling of graphs with given properties.  After a first introductory chapter explaining the motivation, focus, aim and message of the book, chapter 2 introduces the formal construction of maximum-entropy ensembles of graphs with local topological constraints. Chapter 3 focuses on the problem of pattern detection in real networks and provides a powerful way to disentangle nontrivial higher-order structural features from those that can be traced back to simpler local constraints. Chapter 4 focuses on the problem o...

MAXIMUM POWEWR POINT TRACKING SYSTEM FOR PHOTOVOLTAIC STATION: A REVIEW

Directory of Open Access Journals (Sweden)

I. Elzein

2015-01-01

Full Text Available In recent years there has been a growing attention towards the use of renewable energy sources. Among them solar energy is one of the most promising green energy resources due to its environment sustainability and inexhaustibility. However photovoltaic systems (PhV suffer from big cost of equipment and low efficiency. Moreover, the solar cell V-I characteristic is nonlinear and varies with irradiation and temperature. In general, there is a unique point of PhV operation, called the Maximum Power Point (MPP, in which the PV system operates with maximum efficiency and produces its maximum output power. The location of the MPP is not known in advance, but can be located, either through calculation models or by search algorithms. Therefore MPPT techniques are important to maintain the PV array’s high efficiency. Many different techniques for MPPT are discussed. This review paper hopefully will serve as a convenient tool for future work in PhV power conversion.

Science Teachers Sharing Artifacts from Practice like Students’ Tablet Productions

DEFF Research Database (Denmark)

Nielsen, Birgitte Lund

Research looking into the spreading of practices supporting students’ high-level use of ICT for multimedia productions etc. is discussed together with research emphasizing core features of effective professional development for teachers (TPD), as high quality TPD is claimed to be a crucial factor......, are discussed. A case of a teacher’s first experiences from facilitating her students’ productions with the tablet application Explain Everything are used to discuss both the students’ and the teachers’ meaning making, and spreading to more cautious colleagues....

Teachers Sharing Artifacts from Students’ High-level Use of ICT in Science

DEFF Research Database (Denmark)

Nielsen, Birgitte Lund

Research looking into the spreading of practices supporting students’ high-level use of ICT for multimedia productions etc. is discussed together with research emphasizing core features of effective professional development for teachers (TPD), as high quality TPD is claimed to be a crucial factor......, are discussed. A case of a teacher’s first experiences from facilitating her students’ productions with the tablet application Explain Everything are used to discuss both the students’ and the teachers’ meaning making, and spreading to more cautious colleagues....

Maximum Range of a Projectile Thrown from Constant-Speed Circular Motion

Science.gov (United States)

Poljak, Nikola

2016-01-01

The problem of determining the angle ? at which a point mass launched from ground level with a given speed v[subscript 0] will reach a maximum distance is a standard exercise in mechanics. There are many possible ways of solving this problem, leading to the well-known answer of ? = p/4, producing a maximum range of D[subscript max] = v[superscript…

Anti-nutrient components of guinea grass ( Panicum maximum ...

African Journals Online (AJOL)

Yomi

2012-01-31

Jan 31, 2012 ... A true measure of forage quality is animal ... The anti-nutritional contents of a pasture could be ... nutrient factors in P. maximum; (2) assess the effect of nitrogen ..... 3. http://www.clemson.edu/Fairfield/local/news/quality.

Artificial Neural Network In Maximum Power Point Tracking Algorithm Of Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Modestas Pikutis

2014-05-01

Full Text Available Scientists are looking for ways to improve the efficiency of solar cells all the time. The efficiency of solar cells which are available to the general public is up to 20%. Part of the solar energy is unused and a capacity of solar power plant is significantly reduced – if slow controller or controller which cannot stay at maximum power point of solar modules is used. Various algorithms of maximum power point tracking were created, but mostly algorithms are slow or make mistakes. In the literature more and more oftenartificial neural networks (ANN in maximum power point tracking process are mentioned, in order to improve performance of the controller. Self-learner artificial neural network and IncCond algorithm were used for maximum power point tracking in created solar power plant model. The algorithm for control was created. Solar power plant model is implemented in Matlab/Simulink environment.

Seeking the epoch of maximum luminosity for dusty quasars

International Nuclear Information System (INIS)

Vardanyan, Valeri; Weedman, Daniel; Sargsyan, Lusine

2014-01-01

Infrared luminosities νL ν (7.8 μm) arising from dust reradiation are determined for Sloan Digital Sky Survey (SDSS) quasars with 1.4 maximum at any redshift z < 5, reaching a plateau for z ≳ 3 with maximum luminosity νL ν (7.8 μm) ≳ 10 47 erg s –1 ; luminosity functions show one quasar Gpc –3 having νL ν (7.8 μm) > 10 46.6 erg s –1 for all 2 maximum luminosity has not yet been identified at any redshift below 5. The most ultraviolet luminous quasars, defined by rest frame νL ν (0.25 μm), have the largest values of the ratio νL ν (0.25 μm)/νL ν (7.8 μm) with a maximum ratio at z = 2.9. From these results, we conclude that the quasars most luminous in the ultraviolet have the smallest dust content and appear luminous primarily because of lessened extinction. Observed ultraviolet/infrared luminosity ratios are used to define 'obscured' quasars as those having >5 mag of ultraviolet extinction. We present a new summary of obscured quasars discovered with the Spitzer Infrared Spectrograph and determine the infrared luminosity function of these obscured quasars at z ∼ 2.1. This is compared with infrared luminosity functions of optically discovered, unobscured quasars in the SDSS and in the AGN and Galaxy Evolution Survey. The comparison indicates comparable numbers of obscured and unobscured quasars at z ∼ 2.1 with a possible excess of obscured quasars at fainter luminosities.

Maximum total organic carbon limit for DWPF melter feed

International Nuclear Information System (INIS)

Choi, A.S.

1995-01-01

DWPF recently decided to control the potential flammability of melter off-gas by limiting the total carbon content in the melter feed and maintaining adequate conditions for combustion in the melter plenum. With this new strategy, all the LFL analyzers and associated interlocks and alarms were removed from both the primary and backup melter off-gas systems. Subsequently, D. Iverson of DWPF- T ampersand E requested that SRTC determine the maximum allowable total organic carbon (TOC) content in the melter feed which can be implemented as part of the Process Requirements for melter feed preparation (PR-S04). The maximum TOC limit thus determined in this study was about 24,000 ppm on an aqueous slurry basis. At the TOC levels below this, the peak concentration of combustible components in the quenched off-gas will not exceed 60 percent of the LFL during off-gas surges of magnitudes up to three times nominal, provided that the melter plenum temperature and the air purge rate to the BUFC are monitored and controlled above 650 degrees C and 220 lb/hr, respectively. Appropriate interlocks should discontinue the feeding when one or both of these conditions are not met. Both the magnitude and duration of an off-gas surge have a major impact on the maximum TOC limit, since they directly affect the melter plenum temperature and combustion. Although the data obtained during recent DWPF melter startup tests showed that the peak magnitude of a surge can be greater than three times nominal, the observed duration was considerably shorter, on the order of several seconds. The long surge duration assumed in this study has a greater impact on the plenum temperature than the peak magnitude, thus making the maximum TOC estimate conservative. Two models were used to make the necessary calculations to determine the TOC limit

Nonsymmetric entropy and maximum nonsymmetric entropy principle

International Nuclear Information System (INIS)

Liu Chengshi

2009-01-01

Under the frame of a statistical model, the concept of nonsymmetric entropy which generalizes the concepts of Boltzmann's entropy and Shannon's entropy, is defined. Maximum nonsymmetric entropy principle is proved. Some important distribution laws such as power law, can be derived from this principle naturally. Especially, nonsymmetric entropy is more convenient than other entropy such as Tsallis's entropy in deriving power laws.

Remarks on the maximum luminosity

Science.gov (United States)

Cardoso, Vitor; Ikeda, Taishi; Moore, Christopher J.; Yoo, Chul-Moon

2018-04-01

The quest for fundamental limitations on physical processes is old and venerable. Here, we investigate the maximum possible power, or luminosity, that any event can produce. We show, via full nonlinear simulations of Einstein's equations, that there exist initial conditions which give rise to arbitrarily large luminosities. However, the requirement that there is no past horizon in the spacetime seems to limit the luminosity to below the Planck value, LP=c5/G . Numerical relativity simulations of critical collapse yield the largest luminosities observed to date, ≈ 0.2 LP . We also present an analytic solution to the Einstein equations which seems to give an unboundedly large luminosity; this will guide future numerical efforts to investigate super-Planckian luminosities.

Scintillation counter, maximum gamma aspect

International Nuclear Information System (INIS)

Thumim, A.D.

1975-01-01

A scintillation counter, particularly for counting gamma ray photons, includes a massive lead radiation shield surrounding a sample-receiving zone. The shield is disassembleable into a plurality of segments to allow facile installation and removal of a photomultiplier tube assembly, the segments being so constructed as to prevent straight-line access of external radiation through the shield into radiation-responsive areas. Provisions are made for accurately aligning the photomultiplier tube with respect to one or more sample-transmitting bores extending through the shield to the sample receiving zone. A sample elevator, used in transporting samples into the zone, is designed to provide a maximum gamma-receiving aspect to maximize the gamma detecting efficiency. (U.S.)

Comparsion of maximum viscosity and viscometric method for identification of irradiated sweet potato starch

International Nuclear Information System (INIS)

Yi, Sang Duk; Yang, Jae Seung

2000-01-01

A study was carried out to compare viscosity and maximum viscosity methods for the detection of irradiated sweet potato starch. The viscosity of all samples decreased by increasing stirring speeds and irradiation doses. This trend was similar for maximum viscosity. Regression coefficients and expressions of viscosity and maximum viscosity with increasing irradiation dose were 0.9823 (y=335.02e -0. 3 366x ) at 120 rpm and 0.9939 (y =-42.544x+730.26). This trend in viscosity was similar for all stirring speeds. Parameter A, B and C values showed a dose dependent relation and were a better parameter for detecting irradiation treatment than maximum viscosity and the viscosity value it self. These results suggest that the detection of irradiated sweet potato starch is possible by both the viscometric and maximum visosity method. Therefore, the authors think that the maximum viscosity method can be proposed as one of the new methods to detect the irradiation treatment for sweet potato starch

Estimation of maximum credible atmospheric radioactivity concentrations and dose rates from nuclear tests

International Nuclear Information System (INIS)

Telegadas, K.

1979-01-01

A simple technique is presented for estimating maximum credible gross beta air concentrations from nuclear detonations in the atmosphere, based on aircraft sampling of radioactivity following each Chinese nuclear test from 1964 to 1976. The calculated concentration is a function of the total yield and fission yield, initial vertical radioactivity distribution, time after detonation, and rate of horizontal spread of the debris with time. calculated maximum credible concentrations are compared with the highest concentrations measured during aircraft sampling. The technique provides a reasonable estimate of maximum air concentrations from 1 to 10 days after a detonation. An estimate of the whole-body external gamma dose rate corresponding to the maximum credible gross beta concentration is also given. (author)

On the maximum Q in feedback controlled subignited plasmas

International Nuclear Information System (INIS)

Anderson, D.; Hamnen, H.; Lisak, M.

1990-01-01

High Q operation in feedback controlled subignited fusion plasma requires the operating temperature to be close to the ignition temperature. In the present work we discuss technological and physical effects which may restrict this temperature difference. The investigation is based on a simplified, but still accurate, 0=D analytical analysis of the maximum Q of a subignited system. Particular emphasis is given to sawtooth ocsillations which complicate the interpretation of diagnostic neutron emission data into plasma temperatures and may imply an inherent lower bound on the temperature deviation from the ignition point. The estimated maximum Q is found to be marginal (Q = 10-20) from the point of view of a fusion reactor. (authors)

Thermoelectric cooler concepts and the limit for maximum cooling

International Nuclear Information System (INIS)

Seifert, W; Hinsche, N F; Pluschke, V

2014-01-01

The conventional analysis of a Peltier cooler approximates the material properties as independent of temperature using a constant properties model (CPM). Alternative concepts have been published by Bian and Shakouri (2006 Appl. Phys. Lett. 89 212101), Bian (et al 2007 Phys. Rev. B 75 245208) and Snyder et al (2012 Phys. Rev. B 86 045202). While Snyder's Thomson cooler concept results from a consideration of compatibility, the method of Bian et al focuses on the redistribution of heat. Thus, both approaches are based on different principles. In this paper we compare the new concepts to CPM and we reconsider the limit for maximum cooling. The results provide a new perspective on maximum cooling. (paper)

On the maximum of wave surface of sea waves

Energy Technology Data Exchange (ETDEWEB)

Zhang, B

1980-01-01

This article considers wave surface as a normal stationary random process to solve the estimation of the maximum of wave surface in a given time interval by means of the theoretical results of probability theory. The results are represented by formulas (13) to (19) in this article. It was proved in this article that when time interval approaches infinite, the formulas (3), (6) of E )eta max) that were derived from the references (Cartwright, Longuet-Higgins) can also be derived by asymptotic distribution of the maximum of wave surface provided by the article. The advantage of the results obtained from this point of view as compared with the results obtained from the references was discussed.

Surface and bulk crystallization of amorphous solid water films: Confirmation of “top-down” crystallization

Energy Technology Data Exchange (ETDEWEB)

Yuan, Chunqing; Smith, R. Scott; Kay, Bruce D.

2016-10-01

The crystallization kinetics of nanoscale amorphous solid water (ASW) films are investigated using temperature-programmed desorption (TPD) and reflection absorption infrared spectroscopy (RAIRS). TPD measurements are used to probe surface crystallization and RAIRS measurements are used to probe bulk crystallization. Isothermal TPD results show that surface crystallization is independent of the film thickness (from 100 to 1000 ML). Conversely, the RAIRS measurements show that the bulk crystallization time increases linearly with increasing film thickness. These results suggest that nucleation and crystallization begin at the ASW/vacuum interface and then the crystallization growth front propagates linearly into the bulk. This mechanism was confirmed by selective placement of an isotopic layer (5% D2O in H2O) at various positions in an ASW (H2O) film. In this case, the closer the isotopic layer was to the vacuum interface, the earlier the isotopic layer crystallized. These experiments provide direct evidence to confirm that ASW crystallization in vacuum proceeds by a “top-down” crystallization mechanism.

Water Outgassing from PBX-9502 powder by isoconversional thermal analysis

International Nuclear Information System (INIS)

Dinh, L.N.; Glascoe, E.L.; Small, W.

2009-01-01

Temperature programmed desorption/decomposition (TPD) were performed on PBX-9502 after 3 hours of vacuum pump. TPD data were analyzed by the technique of isoconversional analysis to obtain outgassing kinetics and moisture content of PBX-9502 powder as well as to construct water outgassing models for PBX-9502 powder as a function of time and temperature. Following 3 hours of vacuum pump, dry storage of PBX-9502 at 300K, quickly gives rise to 180-330 ppm moisture in the first few years. Thereafter, the moisture outgassing continues at a much slower rate, totaling only to ∼ 210-380 ppm after 100 years of storage. In an effort to understand the nature of the moisture outgassing in PBX-9502, we have measured moisture content and outgassing kinetics in PBX-9502 by the experimental technique of TPD and the isoconversional thermal analysis. The results of these measurements were then used to construct moisture outgassing models for PBX-9502 in a dry environment (following 3 hours of vacuum pump)

Differences in two-point discrimination and sensory threshold in the blind between braille and text reading: a pilot study.

Science.gov (United States)

Noh, Ji-Woong; Park, Byoung-Sun; Kim, Mee-Young; Lee, Lim-Kyu; Yang, Seung-Min; Lee, Won-Deok; Shin, Yong-Sub; Kang, Ji-Hye; Kim, Ju-Hyun; Lee, Jeong-Uk; Kwak, Taek-Yong; Lee, Tae-Hyun; Kim, Ju-Young; Kim, Junghwan

2015-06-01

[Purpose] This study investigated two-point discrimination (TPD) and the electrical sensory threshold of the blind to define the effect of using Braille on the tactile and electrical senses. [Subjects and Methods] Twenty-eight blind participants were divided equally into a text-reading and a Braille-reading group. We measured tactile sensory and electrical thresholds using the TPD method and a transcutaneous electrical nerve stimulator. [Results] The left palm TPD values were significantly different between the groups. The values of the electrical sensory threshold in the left hand, the electrical pain threshold in the left hand, and the electrical pain threshold in the right hand were significantly lower in the Braille group than in the text group. [Conclusion] These findings make it difficult to explain the difference in tactility between groups, excluding both palms. However, our data show that using Braille can enhance development of the sensory median nerve in the blind, particularly in terms of the electrical sensory and pain thresholds.

The effect of the thicknesses of the various layers on the colour emitted by an organic electroluminescent device

Science.gov (United States)

Jolinat, P.; Clergereaux, R.; Farenc, J.; Destruel, P.

1998-05-01

Organic electroluminescent diodes based on thin organic layers are one of the most promising next-generation systems for the backlighting of the liquid crystal screens. Among other methods to obtain white light, three-layer luminescent devices with each layer emitting one of the three fundamental colours have been studied here. Red, green and blue light were produced by 0022-3727/31/10/018/img1 doped with Nile red, 0022-3727/31/10/018/img1 and TPD layers respectively. A fourth thin film of TAZ has been inserted between TPD and 0022-3727/31/10/018/img1 to control injection of electrons into the TPD. The effect of the layers' thicknesses on the spectral emission of the device has been examined. Results show that the thicknesses of TAZ and doped 0022-3727/31/10/018/img1 layers have to be controlled to within a precision of better than 5 Å. The discussion turns on the possibility of applying this technology to screen backlighting.

Ancestral sequence reconstruction with Maximum Parsimony

OpenAIRE

Herbst, Lina; Fischer, Mareike

2017-01-01

One of the main aims in phylogenetics is the estimation of ancestral sequences based on present-day data like, for instance, DNA alignments. One way to estimate the data of the last common ancestor of a given set of species is to first reconstruct a phylogenetic tree with some tree inference method and then to use some method of ancestral state inference based on that tree. One of the best-known methods both for tree inference as well as for ancestral sequence inference is Maximum Parsimony (...

Analysis of Minute Features in Speckled Imagery with Maximum Likelihood Estimation

Directory of Open Access Journals (Sweden)

Alejandro C. Frery

2004-12-01

Full Text Available This paper deals with numerical problems arising when performing maximum likelihood parameter estimation in speckled imagery using small samples. The noise that appears in images obtained with coherent illumination, as is the case of sonar, laser, ultrasound-B, and synthetic aperture radar, is called speckle, and it can neither be assumed Gaussian nor additive. The properties of speckle noise are well described by the multiplicative model, a statistical framework from which stem several important distributions. Amongst these distributions, one is regarded as the universal model for speckled data, namely, the 𝒢0 law. This paper deals with amplitude data, so the 𝒢A0 distribution will be used. The literature reports that techniques for obtaining estimates (maximum likelihood, based on moments and on order statistics of the parameters of the 𝒢A0 distribution require samples of hundreds, even thousands, of observations in order to obtain sensible values. This is verified for maximum likelihood estimation, and a proposal based on alternate optimization is made to alleviate this situation. The proposal is assessed with real and simulated data, showing that the convergence problems are no longer present. A Monte Carlo experiment is devised to estimate the quality of maximum likelihood estimators in small samples, and real data is successfully analyzed with the proposed alternated procedure. Stylized empirical influence functions are computed and used to choose a strategy for computing maximum likelihood estimates that is resistant to outliers.

Erich Regener and the ionisation maximum of the atmosphere

Science.gov (United States)

Carlson, P.; Watson, A. A.

2014-12-01

In the 1930s the German physicist Erich Regener (1881-1955) did important work on the measurement of the rate of production of ionisation deep under water and in the atmosphere. Along with one of his students, Georg Pfotzer, he discovered the altitude at which the production of ionisation in the atmosphere reaches a maximum, often, but misleadingly, called the Pfotzer maximum. Regener was one of the first to estimate the energy density of cosmic rays, an estimate that was used by Baade and Zwicky to bolster their postulate that supernovae might be their source. Yet Regener's name is less recognised by present-day cosmic ray physicists than it should be, largely because in 1937 he was forced to take early retirement by the National Socialists as his wife had Jewish ancestors. In this paper we briefly review his work on cosmic rays and recommend an alternative naming of the ionisation maximum. The influence that Regener had on the field through his son, his son-in-law, his grandsons and his students, and through his links with Rutherford's group in Cambridge, is discussed in an appendix. Regener was nominated for the Nobel Prize in Physics by Schrödinger in 1938. He died in 1955 at the age of 73.

Maximum likelihood as a common computational framework in tomotherapy

International Nuclear Information System (INIS)

Olivera, G.H.; Shepard, D.M.; Reckwerdt, P.J.; Ruchala, K.; Zachman, J.; Fitchard, E.E.; Mackie, T.R.

1998-01-01

Tomotherapy is a dose delivery technique using helical or axial intensity modulated beams. One of the strengths of the tomotherapy concept is that it can incorporate a number of processes into a single piece of equipment. These processes include treatment optimization planning, dose reconstruction and kilovoltage/megavoltage image reconstruction. A common computational technique that could be used for all of these processes would be very appealing. The maximum likelihood estimator, originally developed for emission tomography, can serve as a useful tool in imaging and radiotherapy. We believe that this approach can play an important role in the processes of optimization planning, dose reconstruction and kilovoltage and/or megavoltage image reconstruction. These processes involve computations that require comparable physical methods. They are also based on equivalent assumptions, and they have similar mathematical solutions. As a result, the maximum likelihood approach is able to provide a common framework for all three of these computational problems. We will demonstrate how maximum likelihood methods can be applied to optimization planning, dose reconstruction and megavoltage image reconstruction in tomotherapy. Results for planning optimization, dose reconstruction and megavoltage image reconstruction will be presented. Strengths and weaknesses of the methodology are analysed. Future directions for this work are also suggested. (author)

PTree: pattern-based, stochastic search for maximum parsimony phylogenies

Directory of Open Access Journals (Sweden)

Ivan Gregor

2013-06-01

Full Text Available Phylogenetic reconstruction is vital to analyzing the evolutionary relationship of genes within and across populations of different species. Nowadays, with next generation sequencing technologies producing sets comprising thousands of sequences, robust identification of the tree topology, which is optimal according to standard criteria such as maximum parsimony, maximum likelihood or posterior probability, with phylogenetic inference methods is a computationally very demanding task. Here, we describe a stochastic search method for a maximum parsimony tree, implemented in a software package we named PTree. Our method is based on a new pattern-based technique that enables us to infer intermediate sequences efficiently where the incorporation of these sequences in the current tree topology yields a phylogenetic tree with a lower cost. Evaluation across multiple datasets showed that our method is comparable to the algorithms implemented in PAUP* or TNT, which are widely used by the bioinformatics community, in terms of topological accuracy and runtime. We show that our method can process large-scale datasets of 1,000–8,000 sequences. We believe that our novel pattern-based method enriches the current set of tools and methods for phylogenetic tree inference. The software is available under: http://algbio.cs.uni-duesseldorf.de/webapps/wa-download/.

PTree: pattern-based, stochastic search for maximum parsimony phylogenies.

Science.gov (United States)

Gregor, Ivan; Steinbrück, Lars; McHardy, Alice C

2013-01-01

Phylogenetic reconstruction is vital to analyzing the evolutionary relationship of genes within and across populations of different species. Nowadays, with next generation sequencing technologies producing sets comprising thousands of sequences, robust identification of the tree topology, which is optimal according to standard criteria such as maximum parsimony, maximum likelihood or posterior probability, with phylogenetic inference methods is a computationally very demanding task. Here, we describe a stochastic search method for a maximum parsimony tree, implemented in a software package we named PTree. Our method is based on a new pattern-based technique that enables us to infer intermediate sequences efficiently where the incorporation of these sequences in the current tree topology yields a phylogenetic tree with a lower cost. Evaluation across multiple datasets showed that our method is comparable to the algorithms implemented in PAUP* or TNT, which are widely used by the bioinformatics community, in terms of topological accuracy and runtime. We show that our method can process large-scale datasets of 1,000-8,000 sequences. We believe that our novel pattern-based method enriches the current set of tools and methods for phylogenetic tree inference. The software is available under: http://algbio.cs.uni-duesseldorf.de/webapps/wa-download/.

Extending the maximum operation time of the MNSR reactor.

Science.gov (United States)

Dawahra, S; Khattab, K; Saba, G

2016-09-01

An effective modification to extend the maximum operation time of the Miniature Neutron Source Reactor (MNSR) to enhance the utilization of the reactor has been tested using the MCNP4C code. This modification consisted of inserting manually in each of the reactor inner irradiation tube a chain of three polyethylene-connected containers filled of water. The total height of the chain was 11.5cm. The replacement of the actual cadmium absorber with B(10) absorber was needed as well. The rest of the core structure materials and dimensions remained unchanged. A 3-D neutronic model with the new modifications was developed to compare the neutronic parameters of the old and modified cores. The results of the old and modified core excess reactivities (ρex) were: 3.954, 6.241 mk respectively. The maximum reactor operation times were: 428, 1025min and the safety reactivity factors were: 1.654 and 1.595 respectively. Therefore, a 139% increase in the maximum reactor operation time was noticed for the modified core. This increase enhanced the utilization of the MNSR reactor to conduct a long time irradiation of the unknown samples using the NAA technique and increase the amount of radioisotope production in the reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

An Efficient Algorithm for the Maximum Distance Problem

Directory of Open Access Journals (Sweden)

Gabrielle Assunta Grün

2001-12-01

Full Text Available Efficient algorithms for temporal reasoning are essential in knowledge-based systems. This is central in many areas of Artificial Intelligence including scheduling, planning, plan recognition, and natural language understanding. As such, scalability is a crucial consideration in temporal reasoning. While reasoning in the interval algebra is NP-complete, reasoning in the less expressive point algebra is tractable. In this paper, we explore an extension to the work of Gerevini and Schubert which is based on the point algebra. In their seminal framework, temporal relations are expressed as a directed acyclic graph partitioned into chains and supported by a metagraph data structure, where time points or events are represented by vertices, and directed edges are labelled with < or ≤. They are interested in fast algorithms for determining the strongest relation between two events. They begin by developing fast algorithms for the case where all points lie on a chain. In this paper, we are interested in a generalization of this, namely we consider the problem of finding the maximum ``distance'' between two vertices in a chain ; this problem arises in real world applications such as in process control and crew scheduling. We describe an O(n time preprocessing algorithm for the maximum distance problem on chains. It allows queries for the maximum number of < edges between two vertices to be answered in O(1 time. This matches the performance of the algorithm of Gerevini and Schubert for determining the strongest relation holding between two vertices in a chain.

A conductance maximum observed in an inward-rectifier potassium channel

OpenAIRE

1994-01-01

One prediction of a multi-ion pore is that its conductance should reach a maximum and then begin to decrease as the concentration of permeant ion is raised equally on both sides of the membrane. A conductance maximum has been observed at the single-channel level in gramicidin and in a Ca(2+)-activated K+ channel at extremely high ion concentration (> 1,000 mM) (Hladky, S. B., and D. A. Haydon. 1972. Biochimica et Biophysica Acta. 274:294-312; Eisenmam, G., J. Sandblom, and E. Neher. 1977. In ...

49 CFR 192.619 - Maximum allowable operating pressure: Steel or plastic pipelines.

Science.gov (United States)

2010-10-01

... plastic pipelines. 192.619 Section 192.619 Transportation Other Regulations Relating to Transportation... Operations § 192.619 Maximum allowable operating pressure: Steel or plastic pipelines. (a) No person may operate a segment of steel or plastic pipeline at a pressure that exceeds a maximum allowable operating...

Adaptive Unscented Kalman Filter using Maximum Likelihood Estimation

DEFF Research Database (Denmark)

Mahmoudi, Zeinab; Poulsen, Niels Kjølstad; Madsen, Henrik

2017-01-01

The purpose of this study is to develop an adaptive unscented Kalman filter (UKF) by tuning the measurement noise covariance. We use the maximum likelihood estimation (MLE) and the covariance matching (CM) method to estimate the noise covariance. The multi-step prediction errors generated...

The constraint rule of the maximum entropy principle

NARCIS (Netherlands)

Uffink, J.

1995-01-01

The principle of maximum entropy is a method for assigning values to probability distributions on the basis of partial information. In usual formulations of this and related methods of inference one assumes that this partial information takes the form of a constraint on allowed probability

Maximum Permissible Concentrations and Negligible Concentrations for pesticides

NARCIS (Netherlands)

Crommentuijn T; Kalf DF; Polder MD; Posthumus R; Plassche EJ van de; CSR

1997-01-01

Maximum Permissible Concentrations (MPCs) and Negligible Concentrations (NCs) derived for a series of pesticides are presented in this report. These MPCs and NCs are used by the Ministry of Housing, Spatial Planning and the Environment (VROM) to set Environmental Quality Objectives. For some of the

Phytophthora stricta isolated from Rhododendron maximum in Pennsylvania

Science.gov (United States)

During a survey in October 2013, in the Michaux State Forest in Pennsylvania , necrotic Rhododendron maximum leaves were noticed on mature plants alongside a stream. Symptoms were nondescript necrotic lesions at the tips of mature leaves. Colonies resembling a Phytophthora sp. were observed from c...

PARTICLE SWARM OPTIMIZATION BASED OF THE MAXIMUM PHOTOVOLTAIC POWER TRACTIOQG UNDER DIFFERENT CONDITIONS

Directory of Open Access Journals (Sweden)

Y. Labbi

2015-08-01

Full Text Available Photovoltaic electricity is seen as an important source of renewable energy. The photovoltaic array is an unstable source of power since the peak power point depends on the temperature and the irradiation level. A maximum peak power point tracking is then necessary for maximum efficiency.In this work, a Particle Swarm Optimization (PSO is proposed for maximum power point tracker for photovoltaic panel, are used to generate the optimal MPP, such that solar panel maximum power is generated under different operating conditions. A photovoltaic system including a solar panel and PSO MPP tracker is modelled and simulated, it has been has been carried out which has shown the effectiveness of PSO to draw much energy and fast response against change in working conditions.

5 CFR 9901.312 - Maximum rates of base salary and adjusted salary.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Maximum rates of base salary and adjusted salary. 9901.312 Section 9901.312 Administrative Personnel DEPARTMENT OF DEFENSE HUMAN RESOURCES....312 Maximum rates of base salary and adjusted salary. (a) Subject to § 9901.105, the Secretary may...

The Betz-Joukowsky limit for the maximum power coefficient of wind turbines

DEFF Research Database (Denmark)

Okulov, Valery; van Kuik, G.A.M.

2009-01-01

The article addresses to a history of an important scientific result in wind energy. The maximum efficiency of an ideal wind turbine rotor is well known as the ‘Betz limit’, named after the German scientist that formulated this maximum in 1920. Also Lanchester, a British scientist, is associated...

Effect of Li2O/Al cathode in Alq3 based organic light-emitting diodes.

Science.gov (United States)

Shin, Eun Chul; Ahn, Hui Chul; Han, Wone Keun; Kim, Tae Wan; Lee, Won Jae; Hong, Jin Woong; Chung, Dong Hoe; Song, Min Jong

2008-09-01

An effect of bilayer cathode Li20/Al was studied in Alq3 based organic light-emitting diodes with a variation of Li2O layer thickness. The current-luminance-voltage characteristics of ITO/TPD/Alq3/Li2O/Al device were measured at ambient condition to investigate the effect of Li2O/Al. It was found that when the thickness of Li2O layer is in the range of 0.5-1 nm, there are improvements in luminance, efficiency, and turn-on voltage of the device. A current density and a luminance are increased by about 100 times, a turn-on voltage is lowered from 6 V to 3 V, a maximum current efficiency is improved by a factor of 2.3, and a maximum power efficiency is improved by a factor of 3.2 for a device with a use of thin Li2O layer compared to those of the one without the Li2Otron-barrier height for electron injection from the cathode to the emissive layer.

Multi-Channel Maximum Likelihood Pitch Estimation

DEFF Research Database (Denmark)

Christensen, Mads Græsbøll

2012-01-01

In this paper, a method for multi-channel pitch estimation is proposed. The method is a maximum likelihood estimator and is based on a parametric model where the signals in the various channels share the same fundamental frequency but can have different amplitudes, phases, and noise characteristics....... This essentially means that the model allows for different conditions in the various channels, like different signal-to-noise ratios, microphone characteristics and reverberation. Moreover, the method does not assume that a certain array structure is used but rather relies on a more general model and is hence...

Preparación y caracterización de las propiedades fisicoquímicas del óxido mixto NiO/MgO-La2O3. Efecto de la variación de la composición del soporte

Directory of Open Access Journals (Sweden)

Claudio Lugo

2012-05-01

Full Text Available Mixed oxide catalysts of NiO/MgO-La2O3 varying the proportions support were synthesized through the Lunsford method, successive impregnation. Different techniques were used to determine their physicochemical properties., EDX analysis, FTIR spectroscopy, X-ray diffraction, XRD, thermal methods, TGA, DSC, BET surface area method, temperature programmed reduction, TPR-H2, temperature programmed desorption, TPD-O2 and TPD-NO. The results show that nickel oxide displays a strong interaction with support, depending mainly on the proportion of these components.

Handelman's hierarchy for the maximum stable set problem

NARCIS (Netherlands)

Laurent, M.; Sun, Z.

2014-01-01

The maximum stable set problem is a well-known NP-hard problem in combinatorial optimization, which can be formulated as the maximization of a quadratic square-free polynomial over the (Boolean) hypercube. We investigate a hierarchy of linear programming relaxations for this problem, based on a

Applications of the Maximum Entropy Method in superspace

Czech Academy of Sciences Publication Activity Database

van Smaalen, S.; Palatinus, Lukáš

2004-01-01

Roč. 305, - (2004), s. 57-62 ISSN 0015-0193 Grant - others:DFG and FCI(DE) XX Institutional research plan: CEZ:AV0Z1010914 Keywords : Maximum Entropy Method * modulated structures * charge density Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.517, year: 2004

44 CFR 208.12 - Maximum Pay Rate Table.

Science.gov (United States)

2010-10-01

...) Physicians. DHS uses the latest Special Salary Rate Table Number 0290 for Medical Officers (Clinical... Personnel, in which case the Maximum Pay Rate Table would not apply. (3) Compensation for Sponsoring Agency... organizations, e.g., HMOs or medical or engineering professional associations, under the revised definition of...

Maximum likelihood estimation of the attenuated ultrasound pulse

DEFF Research Database (Denmark)

Rasmussen, Klaus Bolding

1994-01-01

The attenuated ultrasound pulse is divided into two parts: a stationary basic pulse and a nonstationary attenuation pulse. A standard ARMA model is used for the basic pulse, and a nonstandard ARMA model is derived for the attenuation pulse. The maximum likelihood estimator of the attenuated...

correlation between maximum dry density and cohesion of ...

African Journals Online (AJOL)

HOD

investigation on sandy soils to determine the correlation between relative density and compaction test parameter. Using twenty soil samples, they were able to develop correlations between relative density, coefficient of uniformity and maximum dry density. Khafaji [5] using standard proctor compaction method carried out an ...

The scaling of maximum and basal metabolic rates of mammals and birds

Science.gov (United States)

Barbosa, Lauro A.; Garcia, Guilherme J. M.; da Silva, Jafferson K. L.

2006-01-01

Allometric scaling is one of the most pervasive laws in biology. Its origin, however, is still a matter of dispute. Recent studies have established that maximum metabolic rate scales with an exponent larger than that found for basal metabolism. This unpredicted result sets a challenge that can decide which of the concurrent hypotheses is the correct theory. Here, we show that both scaling laws can be deduced from a single network model. Besides the 3/4-law for basal metabolism, the model predicts that maximum metabolic rate scales as M, maximum heart rate as M, and muscular capillary density as M, in agreement with data.

Maximum field capability of energy saver superconducting magnets

International Nuclear Information System (INIS)

Turkot, F.; Cooper, W.E.; Hanft, R.; McInturff, A.

1983-01-01

At an energy of 1 TeV the superconducting cable in the Energy Saver dipole magnets will be operating at ca. 96% of its nominal short sample limit; the corresponding number in the quadrupole magnets will be 81%. All magnets for the Saver are individually tested for maximum current capability under two modes of operation; some 900 dipoles and 275 quadrupoles have now been measured. The dipole winding is composed of four individually wound coils which in general come from four different reels of cable. As part of the magnet fabrication quality control a short piece of cable from both ends of each reel has its critical current measured at 5T and 4.3K. In this paper the authors describe and present the statistical results of the maximum field tests (including quench and cycle) on Saver dipole and quadrupole magnets and explore the correlation of these tests with cable critical current

Algorithms of maximum likelihood data clustering with applications

Science.gov (United States)

Giada, Lorenzo; Marsili, Matteo

2002-12-01

We address the problem of data clustering by introducing an unsupervised, parameter-free approach based on maximum likelihood principle. Starting from the observation that data sets belonging to the same cluster share a common information, we construct an expression for the likelihood of any possible cluster structure. The likelihood in turn depends only on the Pearson's coefficient of the data. We discuss clustering algorithms that provide a fast and reliable approximation to maximum likelihood configurations. Compared to standard clustering methods, our approach has the advantages that (i) it is parameter free, (ii) the number of clusters need not be fixed in advance and (iii) the interpretation of the results is transparent. In order to test our approach and compare it with standard clustering algorithms, we analyze two very different data sets: time series of financial market returns and gene expression data. We find that different maximization algorithms produce similar cluster structures whereas the outcome of standard algorithms has a much wider variability.

Optimal Control of Polymer Flooding Based on Maximum Principle

Directory of Open Access Journals (Sweden)

Yang Lei

2012-01-01

Full Text Available Polymer flooding is one of the most important technologies for enhanced oil recovery (EOR. In this paper, an optimal control model of distributed parameter systems (DPSs for polymer injection strategies is established, which involves the performance index as maximum of the profit, the governing equations as the fluid flow equations of polymer flooding, and the inequality constraint as the polymer concentration limitation. To cope with the optimal control problem (OCP of this DPS, the necessary conditions for optimality are obtained through application of the calculus of variations and Pontryagin’s weak maximum principle. A gradient method is proposed for the computation of optimal injection strategies. The numerical results of an example illustrate the effectiveness of the proposed method.

30 CFR 77.902-1 - Fail safe ground check circuits; maximum voltage.

Science.gov (United States)

2010-07-01

... voltage. 77.902-1 Section 77.902-1 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... OF UNDERGROUND COAL MINES Low- and Medium-Voltage Alternating Current Circuits § 77.902-1 Fail safe ground check circuits; maximum voltage. The maximum voltage used for ground check circuits under § 77.902...

30 CFR 77.803-1 - Fail safe ground check circuits; maximum voltage.

Science.gov (United States)

2010-07-01

... voltage. 77.803-1 Section 77.803-1 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803-1 Fail safe ground check circuits; maximum voltage. The maximum voltage used for ground check circuits under § 77.803 shall not...

Characteristics of Plantar Loads in Maximum Forward Lunge Tasks in Badminton.

Science.gov (United States)

Hu, Xiaoyue; Li, Jing Xian; Hong, Youlian; Wang, Lin

2015-01-01

Badminton players often perform powerful and long-distance lunges during such competitive matches. The objective of this study is to compare the plantar loads of three one-step maximum forward lunges in badminton. Fifteen right-handed male badminton players participated in the study. Each participant performed five successful maximum lunges at three directions. For each direction, the participant wore three different shoe brands. Plantar loading, including peak pressure, maximum force, and contact area, was measured by using an insole pressure measurement system. Two-way ANOVA with repeated measures was employed to determine the effects of the different lunge directions and different shoes, as well as the interaction of these two variables, on the measurements. The maximum force (MF) on the lateral midfoot was lower when performing left-forward lunges than when performing front-forward lunges (p = 0.006, 95% CI = -2.88 to -0.04%BW). The MF and peak pressures (PP) on the great toe region were lower for the front-forward lunge than for the right-forward lunge (MF, p = 0.047, 95% CI = -3.62 to -0.02%BW; PP, p = 0.048, 95% CI = -37.63 to -0.16 KPa) and left-forward lunge (MF, p = 0.015, 95% CI = -4.39 to -0.38%BW; PP, p = 0.008, 95% CI = -47.76 to -5.91 KPa). These findings indicate that compared with the front-forward lunge, left and right maximum forward lunges induce greater plantar loads on the great toe region of the dominant leg of badminton players. The differences in the plantar loads of the different lunge directions may be potential risks for injuries to the lower extremities of badminton players.

Three-level grid-connected photovoltaic inverter with maximum power point tracking

International Nuclear Information System (INIS)

Tsang, K.M.; Chan, W.L.

2013-01-01

Highlight: ► This paper reports a novel 3-level grid connected photovoltaic inverter. ► The inverter features maximum power point tracking and grid current shaping. ► The inverter can be acted as an active filter and a renewable power source. - Abstract: This paper presents a systematic way of designing control scheme for a grid-connected photovoltaic (PV) inverter featuring maximum power point tracking (MPPT) and grid current shaping. Unlike conventional design, only four power switches are required to achieve three output levels and it is not necessary to use any phase-locked-loop circuitry. For the proposed scheme, a simple integral controller has been designed for the tracking of the maximum power point of a PV array based on an improved extremum seeking control method. For the grid-connected inverter, a current loop controller and a voltage loop controller have been designed. The current loop controller is designed to shape the inverter output current while the voltage loop controller can maintain the capacitor voltage at a certain level and provide a reference inverter output current for the PV inverter without affecting the maximum power point of the PV array. Experimental results are included to demonstrate the effectiveness of the tracking and control scheme.

A new sentence generator providing material for maximum reading speed measurement.

Science.gov (United States)

Perrin, Jean-Luc; Paillé, Damien; Baccino, Thierry

2015-12-01

A new method is proposed to generate text material for assessing maximum reading speed of adult readers. The described procedure allows one to generate a vast number of equivalent short sentences. These sentences can be displayed for different durations in order to determine the reader's maximum speed using a psychophysical threshold algorithm. Each sentence is built so that it is either true or false according to common knowledge. The actual reading is verified by asking the reader to determine the truth value of each sentence. We based our design on the generator described by Crossland et al. and upgraded it. The new generator handles concepts distributed in an ontology, which allows an easy determination of the sentences' truth value and control of lexical and psycholinguistic parameters. In this way many equivalent sentence can be generated and displayed to perform the measurement. Maximum reading speed scores obtained with pseudo-randomly chosen sentences from the generator were strongly correlated with maximum reading speed scores obtained with traditional MNREAD sentences (r = .836). Furthermore, the large number of sentences that can be generated makes it possible to perform repeated measurements, since the possibility of a reader learning individual sentences is eliminated. Researchers interested in within-reader performance variability could use the proposed method for this purpose.

Probable maximum flood analysis, Richton Dome, Mississippi-Phase I: Technical report

International Nuclear Information System (INIS)

1987-03-01

This report presents results of a preliminary analysis of the extent of inundation that would result from a probable maximum flood (PMF) event in the overdome area of Richton Dome, Mississippi. Bogue Homo and Thompson Creek watersheds drain the overdome area. The US Army Corps of Engineers' HEC-1 Flood Hydrograph Package was used to calculate runoff hydrographs, route computed flood hydrographs, and determine maximum flood stages at cross sections along overdome tributaries. The area and configuration of stream cross sections were determined from US Geological Survey topographic maps. Using maximum flood stages calculated by the HEC-1 analysis, areas of inundation were delineated on 10-ft (3-m) contour interval topographic maps. Approximately 10% of the overdome area, or 0.9 mi 2 (2 km 2 ), would be inundated by a PMF event. 34 refs., 3 figs., 1 tab

Evaluation of maximum power point tracking in hydrokinetic energy conversion systems

Directory of Open Access Journals (Sweden)

Jahangir Khan

2015-11-01

Full Text Available Maximum power point tracking is a mature control issue for wind, solar and other systems. On the other hand, being a relatively new technology, detailed discussion on power tracking of hydrokinetic energy conversion systems are generally not available. Prior to developing sophisticated control schemes for use in hydrokinetic systems, existing know-how in wind or solar technologies can be explored. In this study, a comparative evaluation of three generic classes of maximum power point scheme is carried out. These schemes are (a tip speed ratio control, (b power signal feedback control, and (c hill climbing search control. In addition, a novel concept for maximum power point tracking: namely, extremum seeking control is introduced. Detailed and validated system models are used in a simulation environment. Potential advantages and drawbacks of each of these schemes are summarised.

Modelling maximum river flow by using Bayesian Markov Chain Monte Carlo

Science.gov (United States)

Cheong, R. Y.; Gabda, D.

2017-09-01

Analysis of flood trends is vital since flooding threatens human living in terms of financial, environment and security. The data of annual maximum river flows in Sabah were fitted into generalized extreme value (GEV) distribution. Maximum likelihood estimator (MLE) raised naturally when working with GEV distribution. However, previous researches showed that MLE provide unstable results especially in small sample size. In this study, we used different Bayesian Markov Chain Monte Carlo (MCMC) based on Metropolis-Hastings algorithm to estimate GEV parameters. Bayesian MCMC method is a statistical inference which studies the parameter estimation by using posterior distribution based on Bayes’ theorem. Metropolis-Hastings algorithm is used to overcome the high dimensional state space faced in Monte Carlo method. This approach also considers more uncertainty in parameter estimation which then presents a better prediction on maximum river flow in Sabah.

A General Stochastic Maximum Principle for SDEs of Mean-field Type

International Nuclear Information System (INIS)

Buckdahn, Rainer; Djehiche, Boualem; Li Juan

2011-01-01

We study the optimal control for stochastic differential equations (SDEs) of mean-field type, in which the coefficients depend on the state of the solution process as well as of its expected value. Moreover, the cost functional is also of mean-field type. This makes the control problem time inconsistent in the sense that the Bellman optimality principle does not hold. For a general action space a Peng’s-type stochastic maximum principle (Peng, S.: SIAM J. Control Optim. 2(4), 966–979, 1990) is derived, specifying the necessary conditions for optimality. This maximum principle differs from the classical one in the sense that here the first order adjoint equation turns out to be a linear mean-field backward SDE, while the second order adjoint equation remains the same as in Peng’s stochastic maximum principle.

Design and optimization of automotive thermoelectric generators for maximum fuel efficiency improvement

International Nuclear Information System (INIS)

Kempf, Nicholas; Zhang, Yanliang

2016-01-01

Highlights: • A three-dimensional automotive thermoelectric generator (TEG) model is developed. • Heat exchanger design and TEG configuration are optimized for maximum fuel efficiency increase. • Heat exchanger conductivity has a strong influence on maximum fuel efficiency increase. • TEG aspect ratio and fin height increase with heat exchanger thermal conductivity. • A 2.5% fuel efficiency increase is attainable with nanostructured half-Heusler modules. - Abstract: Automotive fuel efficiency can be increased by thermoelectric power generation using exhaust waste heat. A high-temperature thermoelectric generator (TEG) that converts engine exhaust waste heat into electricity is simulated based on a light-duty passenger vehicle with a 4-cylinder gasoline engine. Strategies to optimize TEG configuration and heat exchanger design for maximum fuel efficiency improvement are provided. Through comparison of stainless steel and silicon carbide heat exchangers, it is found that both the optimal TEG design and the maximum fuel efficiency increase are highly dependent on the thermal conductivity of the heat exchanger material. Significantly higher fuel efficiency increase can be obtained using silicon carbide heat exchangers at taller fins and a longer TEG along the exhaust flow direction when compared to stainless steel heat exchangers. Accounting for major parasitic losses, a maximum fuel efficiency increase of 2.5% is achievable using newly developed nanostructured bulk half-Heusler thermoelectric modules.

The maximum entropy method of moments and Bayesian probability theory

Science.gov (United States)

Bretthorst, G. Larry

2013-08-01

The problem of density estimation occurs in many disciplines. For example, in MRI it is often necessary to classify the types of tissues in an image. To perform this classification one must first identify the characteristics of the tissues to be classified. These characteristics might be the intensity of a T1 weighted image and in MRI many other types of characteristic weightings (classifiers) may be generated. In a given tissue type there is no single intensity that characterizes the tissue, rather there is a distribution of intensities. Often this distributions can be characterized by a Gaussian, but just as often it is much more complicated. Either way, estimating the distribution of intensities is an inference problem. In the case of a Gaussian distribution, one must estimate the mean and standard deviation. However, in the Non-Gaussian case the shape of the density function itself must be inferred. Three common techniques for estimating density functions are binned histograms [1, 2], kernel density estimation [3, 4], and the maximum entropy method of moments [5, 6]. In the introduction, the maximum entropy method of moments will be reviewed. Some of its problems and conditions under which it fails will be discussed. Then in later sections, the functional form of the maximum entropy method of moments probability distribution will be incorporated into Bayesian probability theory. It will be shown that Bayesian probability theory solves all of the problems with the maximum entropy method of moments. One gets posterior probabilities for the Lagrange multipliers, and, finally, one can put error bars on the resulting estimated density function.

Tsallis distribution as a standard maximum entropy solution with 'tail' constraint

International Nuclear Information System (INIS)

Bercher, J.-F.

2008-01-01

We show that Tsallis' distributions can be derived from the standard (Shannon) maximum entropy setting, by incorporating a constraint on the divergence between the distribution and another distribution imagined as its tail. In this setting, we find an underlying entropy which is the Renyi entropy. Furthermore, escort distributions and generalized means appear as a direct consequence of the construction. Finally, the 'maximum entropy tail distribution' is identified as a Generalized Pareto Distribution

Maximum principles for boundary-degenerate second-order linear elliptic differential operators

OpenAIRE

Feehan, Paul M. N.

2012-01-01

We prove weak and strong maximum principles, including a Hopf lemma, for smooth subsolutions to equations defined by linear, second-order, partial differential operators whose principal symbols vanish along a portion of the domain boundary. The boundary regularity property of the smooth subsolutions along this boundary vanishing locus ensures that these maximum principles hold irrespective of the sign of the Fichera function. Boundary conditions need only be prescribed on the complement in th...

Maximum drawdown and the allocation to real estate

NARCIS (Netherlands)

Hamelink, F.; Hoesli, M.

2004-01-01

The role of real estate in a mixed-asset portfolio is investigated when the maximum drawdown (hereafter MaxDD), rather than the standard deviation, is used as the measure of risk. In particular, it is analysed whether the discrepancy between the optimal allocation to real estate and the actual

Assessment of the phytoremediation potential of Panicum maximum ...

African Journals Online (AJOL)

Obvious signs of phyto-toxicity however appeared in plants exposed to 120 ppm Pb2+ and Cd2+ at day twenty-three, suggesting that P. maximum may be a moderate metal accumulator. Keywords: phytoremediation, heavy metals, uptake, tissues, accumulator. African Journal of Biotechnology, Vol 13(19), 1979-1984 ...

Design of simplified maximum-likelihood receivers for multiuser CPM systems.

Science.gov (United States)

Bing, Li; Bai, Baoming

2014-01-01

A class of simplified maximum-likelihood receivers designed for continuous phase modulation based multiuser systems is proposed. The presented receiver is built upon a front end employing mismatched filters and a maximum-likelihood detector defined in a low-dimensional signal space. The performance of the proposed receivers is analyzed and compared to some existing receivers. Some schemes are designed to implement the proposed receivers and to reveal the roles of different system parameters. Analysis and numerical results show that the proposed receivers can approach the optimum multiuser receivers with significantly (even exponentially in some cases) reduced complexity and marginal performance degradation.

Interaction of carbon dioxide with Cu overlayers on Pt(111)

DEFF Research Database (Denmark)

Schumacher, N.; Andersson, Klas Jerker; Grabow, L.C.

2008-01-01

Experimental and theoretical studies on the interaction of carbon dioxide with pseudomorphic and rough copper layers deposited on a platinum (111) single crystal are reported. Evidence for carbon dioxide dissociation and carbonate formation is presented and the relevance to methanol synthesis......) reveals a broad high temperature desorption state for CO2 with peak maximum around 450 K. X-ray photoelectron spectroscopy (XPS) shows that approximately one third of the oxygen accumulated on the surface upon CO2 exposure remains after TPD, indicative of carbonate formation via CO2 dissociation supplying...... O-ads and then facile CO2 + O-ads association, as well as subsequent decomposition at higher temperatures. Density functional theory studies of stepped Cu and Cu/Pt slabs reproduce vibrational frequencies of the carbonate, suggesting a nearly flat tridentate configuration at steps/defect sites....

Maximum Aerobic Capacity of Underground Coal Miners in India

Directory of Open Access Journals (Sweden)

Ratnadeep Saha

2011-01-01

Full Text Available Miners fitness test was assessed in terms of determination of maximum aerobic capacity by an indirect method following a standard step test protocol before going down to mine by taking into consideration of heart rates (Telemetric recording and oxygen consumption of the subjects (Oxylog-II during exercise at different working rates. Maximal heart rate was derived as 220−age. Coal miners reported a maximum aerobic capacity within a range of 35–38.3 mL/kg/min. It also revealed that oldest miners (50–59 yrs had a lowest maximal oxygen uptake (34.2±3.38 mL/kg/min compared to (42.4±2.03 mL/kg/min compared to (42.4±2.03 mL/kg/min the youngest group (20–29 yrs. It was found to be negatively correlated with age (r=−0.55 and −0.33 for younger and older groups respectively and directly associated with the body weight of the subjects (r=0.57 – 0.68, P≤0.001. Carriers showed maximum cardio respiratory capacity compared to other miners. Indian miners VO2max was found to be lower both compared to their abroad mining counterparts and various other non-mining occupational working groups in India.

Environmental Monitoring, Water Quality - Total Maximum Daily Load (TMDL)

Data.gov (United States)

NSGIC Education | GIS Inventory — The Clean Water Act Section 303(d) establishes the Total Maximum Daily Load (TMDL) program. The purpose of the TMDL program is to identify sources of pollution and...

5 CFR 531.221 - Maximum payable rate rule.

Science.gov (United States)

2010-01-01

... before the reassignment. (ii) If the rate resulting from the geographic conversion under paragraph (c)(2... previous rate (i.e., the former special rate after the geographic conversion) with the rates on the current... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Maximum payable rate rule. 531.221...

Predicting the Outcome of NBA Playoffs Based on the Maximum Entropy Principle

Directory of Open Access Journals (Sweden)

Ge Cheng

2016-12-01

Full Text Available Predicting the outcome of National Basketball Association (NBA matches poses a challenging problem of interest to the research community as well as the general public. In this article, we formalize the problem of predicting NBA game results as a classification problem and apply the principle of Maximum Entropy to construct an NBA Maximum Entropy (NBAME model that fits to discrete statistics for NBA games, and then predict the outcomes of NBA playoffs using the model. Our results reveal that the model is able to predict the winning team with 74.4% accuracy, outperforming other classical machine learning algorithms that could only afford a maximum prediction accuracy of 70.6% in the experiments that we performed.

Novel methods for estimating lithium-ion battery state of energy and maximum available energy

International Nuclear Information System (INIS)

Zheng, Linfeng; Zhu, Jianguo; Wang, Guoxiu; He, Tingting; Wei, Yiying

2016-01-01

Highlights: • Study on temperature, current, aging dependencies of maximum available energy. • Study on the various factors dependencies of relationships between SOE and SOC. • A quantitative relationship between SOE and SOC is proposed for SOE estimation. • Estimate maximum available energy by means of moving-window energy-integral. • The robustness and feasibility of the proposed approaches are systematic evaluated. - Abstract: The battery state of energy (SOE) allows a direct determination of the ratio between the remaining and maximum available energy of a battery, which is critical for energy optimization and management in energy storage systems. In this paper, the ambient temperature, battery discharge/charge current rate and cell aging level dependencies of battery maximum available energy and SOE are comprehensively analyzed. An explicit quantitative relationship between SOE and state of charge (SOC) for LiMn_2O_4 battery cells is proposed for SOE estimation, and a moving-window energy-integral technique is incorporated to estimate battery maximum available energy. Experimental results show that the proposed approaches can estimate battery maximum available energy and SOE with high precision. The robustness of the proposed approaches against various operation conditions and cell aging levels is systematically evaluated.

Superfast maximum-likelihood reconstruction for quantum tomography

Science.gov (United States)

Shang, Jiangwei; Zhang, Zhengyun; Ng, Hui Khoon

2017-06-01

Conventional methods for computing maximum-likelihood estimators (MLE) often converge slowly in practical situations, leading to a search for simplifying methods that rely on additional assumptions for their validity. In this work, we provide a fast and reliable algorithm for maximum-likelihood reconstruction that avoids this slow convergence. Our method utilizes the state-of-the-art convex optimization scheme, an accelerated projected-gradient method, that allows one to accommodate the quantum nature of the problem in a different way than in the standard methods. We demonstrate the power of our approach by comparing its performance with other algorithms for n -qubit state tomography. In particular, an eight-qubit situation that purportedly took weeks of computation time in 2005 can now be completed in under a minute for a single set of data, with far higher accuracy than previously possible. This refutes the common claim that MLE reconstruction is slow and reduces the need for alternative methods that often come with difficult-to-verify assumptions. In fact, recent methods assuming Gaussian statistics or relying on compressed sensing ideas are demonstrably inapplicable for the situation under consideration here. Our algorithm can be applied to general optimization problems over the quantum state space; the philosophy of projected gradients can further be utilized for optimization contexts with general constraints.

Objective Bayesianism and the Maximum Entropy Principle

Directory of Open Access Journals (Sweden)

Jon Williamson

2013-09-01

Full Text Available Objective Bayesian epistemology invokes three norms: the strengths of our beliefs should be probabilities; they should be calibrated to our evidence of physical probabilities; and they should otherwise equivocate sufficiently between the basic propositions that we can express. The three norms are sometimes explicated by appealing to the maximum entropy principle, which says that a belief function should be a probability function, from all those that are calibrated to evidence, that has maximum entropy. However, the three norms of objective Bayesianism are usually justified in different ways. In this paper, we show that the three norms can all be subsumed under a single justification in terms of minimising worst-case expected loss. This, in turn, is equivalent to maximising a generalised notion of entropy. We suggest that requiring language invariance, in addition to minimising worst-case expected loss, motivates maximisation of standard entropy as opposed to maximisation of other instances of generalised entropy. Our argument also provides a qualified justification for updating degrees of belief by Bayesian conditionalisation. However, conditional probabilities play a less central part in the objective Bayesian account than they do under the subjective view of Bayesianism, leading to a reduced role for Bayes’ Theorem.

Methodological aspects of crossover and maximum fat-oxidation rate point determination.

Science.gov (United States)

Michallet, A-S; Tonini, J; Regnier, J; Guinot, M; Favre-Juvin, A; Bricout, V; Halimi, S; Wuyam, B; Flore, P

2008-11-01

Indirect calorimetry during exercise provides two metabolic indices of substrate oxidation balance: the crossover point (COP) and maximum fat oxidation rate (LIPOXmax). We aimed to study the effects of the analytical device, protocol type and ventilatory response on variability of these indices, and the relationship with lactate and ventilation thresholds. After maximum exercise testing, 14 relatively fit subjects (aged 32+/-10 years; nine men, five women) performed three submaximum graded tests: one was based on a theoretical maximum power (tMAP) reference; and two were based on the true maximum aerobic power (MAP). Gas exchange was measured concomitantly using a Douglas bag (D) and an ergospirometer (E). All metabolic indices were interpretable only when obtained by the D reference method and MAP protocol. Bland and Altman analysis showed overestimation of both indices with E versus D. Despite no mean differences between COP and LIPOXmax whether tMAP or MAP was used, the individual data clearly showed disagreement between the two protocols. Ventilation explained 10-16% of the metabolic index variations. COP was correlated with ventilation (r=0.96, P<0.01) and the rate of increase in blood lactate (r=0.79, P<0.01), and LIPOXmax correlated with the ventilation threshold (r=0.95, P<0.01). This study shows that, in fit healthy subjects, the analytical device, reference used to build the protocol and ventilation responses affect metabolic indices. In this population, and particularly to obtain interpretable metabolic indices, we recommend a protocol based on the true MAP or one adapted to include the transition from fat to carbohydrate. The correlation between metabolic indices and lactate/ventilation thresholds suggests that shorter, classical maximum progressive exercise testing may be an alternative means of estimating these indices in relatively fit subjects. However, this needs to be confirmed in patients who have metabolic defects.

Characteristics of Plantar Loads in Maximum Forward Lunge Tasks in Badminton.

Directory of Open Access Journals (Sweden)

Xiaoyue Hu

Full Text Available Badminton players often perform powerful and long-distance lunges during such competitive matches. The objective of this study is to compare the plantar loads of three one-step maximum forward lunges in badminton.Fifteen right-handed male badminton players participated in the study. Each participant performed five successful maximum lunges at three directions. For each direction, the participant wore three different shoe brands. Plantar loading, including peak pressure, maximum force, and contact area, was measured by using an insole pressure measurement system. Two-way ANOVA with repeated measures was employed to determine the effects of the different lunge directions and different shoes, as well as the interaction of these two variables, on the measurements.The maximum force (MF on the lateral midfoot was lower when performing left-forward lunges than when performing front-forward lunges (p = 0.006, 95% CI = -2.88 to -0.04%BW. The MF and peak pressures (PP on the great toe region were lower for the front-forward lunge than for the right-forward lunge (MF, p = 0.047, 95% CI = -3.62 to -0.02%BW; PP, p = 0.048, 95% CI = -37.63 to -0.16 KPa and left-forward lunge (MF, p = 0.015, 95% CI = -4.39 to -0.38%BW; PP, p = 0.008, 95% CI = -47.76 to -5.91 KPa.These findings indicate that compared with the front-forward lunge, left and right maximum forward lunges induce greater plantar loads on the great toe region of the dominant leg of badminton players. The differences in the plantar loads of the different lunge directions may be potential risks for injuries to the lower extremities of badminton players.

Tutte sets in graphs II: The complexity of finding maximum Tutte sets

NARCIS (Netherlands)

Bauer, D.; Broersma, Haitze J.; Kahl, N.; Morgana, A.; Schmeichel, E.; Surowiec, T.

2007-01-01

A well-known formula of Tutte and Berge expresses the size of a maximum matching in a graph $G$ in terms of what is usually called the deficiency. A subset $X$ of $V(G)$ for which this deficiency is attained is called a Tutte set of $G$. While much is known about maximum matchings, less is known

A short proof that phylogenetic tree reconstruction by maximum likelihood is hard.

Science.gov (United States)

Roch, Sebastien

2006-01-01

Maximum likelihood is one of the most widely used techniques to infer evolutionary histories. Although it is thought to be intractable, a proof of its hardness has been lacking. Here, we give a short proof that computing the maximum likelihood tree is NP-hard by exploiting a connection between likelihood and parsimony observed by Tuffley and Steel.

A Short Proof that Phylogenetic Tree Reconstruction by Maximum Likelihood is Hard

OpenAIRE

Roch, S.

2005-01-01

Maximum likelihood is one of the most widely used techniques to infer evolutionary histories. Although it is thought to be intractable, a proof of its hardness has been lacking. Here, we give a short proof that computing the maximum likelihood tree is NP-hard by exploiting a connection between likelihood and parsimony observed by Tuffley and Steel.

Dynamical maximum entropy approach to flocking.

Science.gov (United States)

Cavagna, Andrea; Giardina, Irene; Ginelli, Francesco; Mora, Thierry; Piovani, Duccio; Tavarone, Raffaele; Walczak, Aleksandra M

2014-04-01

We derive a new method to infer from data the out-of-equilibrium alignment dynamics of collectively moving animal groups, by considering the maximum entropy model distribution consistent with temporal and spatial correlations of flight direction. When bird neighborhoods evolve rapidly, this dynamical inference correctly learns the parameters of the model, while a static one relying only on the spatial correlations fails. When neighbors change slowly and the detailed balance is satisfied, we recover the static procedure. We demonstrate the validity of the method on simulated data. The approach is applicable to other systems of active matter.

Maximum entropy PDF projection: A review

Science.gov (United States)

Baggenstoss, Paul M.

2017-06-01

We review maximum entropy (MaxEnt) PDF projection, a method with wide potential applications in statistical inference. The method constructs a sampling distribution for a high-dimensional vector x based on knowing the sampling distribution p(z) of a lower-dimensional feature z = T (x). Under mild conditions, the distribution p(x) having highest possible entropy among all distributions consistent with p(z) may be readily found. Furthermore, the MaxEnt p(x) may be sampled, making the approach useful in Monte Carlo methods. We review the theorem and present a case study in model order selection and classification for handwritten character recognition.

A maximum power point tracking algorithm for buoy-rope-drum wave energy converters

Science.gov (United States)

Wang, J. Q.; Zhang, X. C.; Zhou, Y.; Cui, Z. C.; Zhu, L. S.

2016-08-01

The maximum power point tracking control is the key link to improve the energy conversion efficiency of wave energy converters (WEC). This paper presents a novel variable step size Perturb and Observe maximum power point tracking algorithm with a power classification standard for control of a buoy-rope-drum WEC. The algorithm and simulation model of the buoy-rope-drum WEC are presented in details, as well as simulation experiment results. The results show that the algorithm tracks the maximum power point of the WEC fast and accurately.

Encoding Strategy for Maximum Noise Tolerance Bidirectional Associative Memory

National Research Council Canada - National Science Library

Shen, Dan

2003-01-01

In this paper, the Basic Bidirectional Associative Memory (BAM) is extended by choosing weights in the correlation matrix, for a given set of training pairs, which result in a maximum noise tolerance set for BAM...

Suppressing Two-Plasmon Decay with Laser Frequency Detuning

Science.gov (United States)

Follett, R. K.; Shaw, J. G.; Myatt, J. F.; Palastro, J. P.; Short, R. W.; Froula, D. H.

2018-03-01

Three-dimensional laser-plasma interaction simulations show that laser frequency detuning by an amount achievable with current laser technology can be used to suppress the two-plasmon decay (TPD) instability and the corresponding hot-electron generation. For the plasma conditions and laser configuration in a direct-drive inertial confinement fusion implosion on the OMEGA laser, the simulations show that ˜0.7 % laser frequency detuning is sufficient to eliminate TPD-driven hot-electron generation in current experiments. This allows for higher ablation pressures in future implosion designs by using higher laser intensities.

Maximum entropy analysis of liquid diffraction data

International Nuclear Information System (INIS)

Root, J.H.; Egelstaff, P.A.; Nickel, B.G.

1986-01-01

A maximum entropy method for reducing truncation effects in the inverse Fourier transform of structure factor, S(q), to pair correlation function, g(r), is described. The advantages and limitations of the method are explored with the PY hard sphere structure factor as model input data. An example using real data on liquid chlorine, is then presented. It is seen that spurious structure is greatly reduced in comparison to traditional Fourier transform methods. (author)

Gamma-ray spectra deconvolution by maximum-entropy methods

International Nuclear Information System (INIS)

Los Arcos, J.M.

1996-01-01

A maximum-entropy method which includes the response of detectors and the statistical fluctuations of spectra is described and applied to the deconvolution of γ-ray spectra. Resolution enhancement of 25% can be reached for experimental peaks and up to 50% for simulated ones, while the intensities are conserved within 1-2%. (orig.)

SIMULATION OF NEW SIMPLE FUZZY LOGIC MAXIMUM POWER ...

African Journals Online (AJOL)

2010-06-30

Jun 30, 2010 ... Basic structure photovoltaic system Solar array mathematic ... The equivalent circuit model of a solar cell consists of a current generator and a diode .... control of boost converter (tracker) such that maximum power is achieved at the output of the solar panel. Fig.11. The membership function of input. Fig.12.

System for memorizing maximum values

Science.gov (United States)

Bozeman, Richard J., Jr.

1992-08-01

The invention discloses a system capable of memorizing maximum sensed values. The system includes conditioning circuitry which receives the analog output signal from a sensor transducer. The conditioning circuitry rectifies and filters the analog signal and provides an input signal to a digital driver, which may be either linear or logarithmic. The driver converts the analog signal to discrete digital values, which in turn triggers an output signal on one of a plurality of driver output lines n. The particular output lines selected is dependent on the converted digital value. A microfuse memory device connects across the driver output lines, with n segments. Each segment is associated with one driver output line, and includes a microfuse that is blown when a signal appears on the associated driver output line.

Local Times of Galactic Cosmic Ray Intensity Maximum and Minimum in the Diurnal Variation

Directory of Open Access Journals (Sweden)

Su Yeon Oh

2006-06-01

Full Text Available The Diurnal variation of galactic cosmic ray (GCR flux intensity observed by the ground Neutron Monitor (NM shows a sinusoidal pattern with the amplitude of 1sim 2 % of daily mean. We carried out a statistical study on tendencies of the local times of GCR intensity daily maximum and minimum. To test the influences of the solar activity and the location (cut-off rigidity on the distribution in the local times of maximum and minimum GCR intensity, we have examined the data of 1996 (solar minimum and 2000 (solar maximum at the low-latitude Haleakala (latitude: 20.72 N, cut-off rigidity: 12.91 GeV and the high-latitude Oulu (latitude: 65.05 N, cut-off rigidity: 0.81 GeV NM stations. The most frequent local times of the GCR intensity daily maximum and minimum come later about 2sim3 hours in the solar activity maximum year 2000 than in the solar activity minimum year 1996. Oulu NM station whose cut-off rigidity is smaller has the most frequent local times of the GCR intensity maximum and minimum later by 2sim3 hours from those of Haleakala station. This feature is more evident at the solar maximum. The phase of the daily variation in GCR is dependent upon the interplanetary magnetic field varying with the solar activity and the cut-off rigidity varying with the geographic latitude.

An extended heterogeneous car-following model accounting for anticipation driving behavior and mixed maximum speeds

Science.gov (United States)

Sun, Fengxin; Wang, Jufeng; Cheng, Rongjun; Ge, Hongxia

2018-02-01

The optimal driving speeds of the different vehicles may be different for the same headway. In the optimal velocity function of the optimal velocity (OV) model, the maximum speed vmax is an important parameter determining the optimal driving speed. A vehicle with higher maximum speed is more willing to drive faster than that with lower maximum speed in similar situation. By incorporating the anticipation driving behavior of relative velocity and mixed maximum speeds of different percentages into optimal velocity function, an extended heterogeneous car-following model is presented in this paper. The analytical linear stable condition for this extended heterogeneous traffic model is obtained by using linear stability theory. Numerical simulations are carried out to explore the complex phenomenon resulted from the cooperation between anticipation driving behavior and heterogeneous maximum speeds in the optimal velocity function. The analytical and numerical results all demonstrate that strengthening driver's anticipation effect can improve the stability of heterogeneous traffic flow, and increasing the lowest value in the mixed maximum speeds will result in more instability, but increasing the value or proportion of the part already having higher maximum speed will cause different stabilities at high or low traffic densities.

Exact parallel maximum clique algorithm for general and protein graphs.

Science.gov (United States)

Depolli, Matjaž; Konc, Janez; Rozman, Kati; Trobec, Roman; Janežič, Dušanka

2013-09-23

A new exact parallel maximum clique algorithm MaxCliquePara, which finds the maximum clique (the fully connected subgraph) in undirected general and protein graphs, is presented. First, a new branch and bound algorithm for finding a maximum clique on a single computer core, which builds on ideas presented in two published state of the art sequential algorithms is implemented. The new sequential MaxCliqueSeq algorithm is faster than the reference algorithms on both DIMACS benchmark graphs as well as on protein-derived product graphs used for protein structural comparisons. Next, the MaxCliqueSeq algorithm is parallelized by splitting the branch-and-bound search tree to multiple cores, resulting in MaxCliquePara algorithm. The ability to exploit all cores efficiently makes the new parallel MaxCliquePara algorithm markedly superior to other tested algorithms. On a 12-core computer, the parallelization provides up to 2 orders of magnitude faster execution on the large DIMACS benchmark graphs and up to an order of magnitude faster execution on protein product graphs. The algorithms are freely accessible on http://commsys.ijs.si/~matjaz/maxclique.

Design of Simplified Maximum-Likelihood Receivers for Multiuser CPM Systems

Directory of Open Access Journals (Sweden)

Li Bing

2014-01-01

Full Text Available A class of simplified maximum-likelihood receivers designed for continuous phase modulation based multiuser systems is proposed. The presented receiver is built upon a front end employing mismatched filters and a maximum-likelihood detector defined in a low-dimensional signal space. The performance of the proposed receivers is analyzed and compared to some existing receivers. Some schemes are designed to implement the proposed receivers and to reveal the roles of different system parameters. Analysis and numerical results show that the proposed receivers can approach the optimum multiuser receivers with significantly (even exponentially in some cases reduced complexity and marginal performance degradation.

A thermoelectric generator using loop heat pipe and design match for maximum-power generation

KAUST Repository

Huang, Bin-Juine

2015-09-05

The present study focuses on the thermoelectric generator (TEG) using loop heat pipe (LHP) and design match for maximum-power generation. The TEG uses loop heat pipe, a passive cooling device, to dissipate heat without consuming power and free of noise. The experiments for a TEG with 4W rated power show that the LHP performs very well with overall thermal resistance 0.35 K W-1, from the cold side of TEG module to the ambient. The LHP is able to dissipate heat up to 110W and is maintenance free. The TEG design match for maximum-power generation, called “near maximum-power point operation (nMPPO)”, is studied to eliminate the MPPT (maximum-power point tracking controller). nMPPO is simply a system design which properly matches the output voltage of TEG with the battery. It is experimentally shown that TEG using design match for maximum-power generation (nMPPO) performs better than TEG with MPPT.

ORIGINAL ARTICLES Surgical practice in a maximum security prison

African Journals Online (AJOL)

Prison Clinic, Mangaung Maximum Security Prison, Bloemfontein. F Kleinhans, BA (Cur) .... HIV positivity rate and the use of the rectum to store foreign objects. ... fruit in sunlight. Other positive health-promoting factors may also play a role,.

Overview of Maximum Power Point Tracking Techniques for Photovoltaic Energy Production Systems

DEFF Research Database (Denmark)

Koutroulis, Eftichios; Blaabjerg, Frede

2015-01-01

A substantial growth of the installed photovoltaic systems capacity has occurred around the world during the last decade, thus enhancing the availability of electric energy in an environmentally friendly way. The maximum power point tracking technique enables maximization of the energy production...... of photovoltaic sources during stochastically varying solar irradiation and ambient temperature conditions. Thus, the overall efficiency of the photovoltaic energy production system is increased. Numerous techniques have been presented during the last decade for implementing the maximum power point tracking...... process in a photovoltaic system. This article provides an overview of the operating principles of these techniques, which are suited for either uniform or non-uniform solar irradiation conditions. The operational characteristics and implementation requirements of these maximum power point tracking...

Rapid calculation of maximum particle lifetime for diffusion in complex geometries

Science.gov (United States)

Carr, Elliot J.; Simpson, Matthew J.

2018-03-01

Diffusion of molecules within biological cells and tissues is strongly influenced by crowding. A key quantity to characterize diffusion is the particle lifetime, which is the time taken for a diffusing particle to exit by hitting an absorbing boundary. Calculating the particle lifetime provides valuable information, for example, by allowing us to compare the timescale of diffusion and the timescale of the reaction, thereby helping us to develop appropriate mathematical models. Previous methods to quantify particle lifetimes focus on the mean particle lifetime. Here, we take a different approach and present a simple method for calculating the maximum particle lifetime. This is the time after which only a small specified proportion of particles in an ensemble remain in the system. Our approach produces accurate estimates of the maximum particle lifetime, whereas the mean particle lifetime always underestimates this value compared with data from stochastic simulations. Furthermore, we find that differences between the mean and maximum particle lifetimes become increasingly important when considering diffusion hindered by obstacles.

The maximum contraceptive prevalence 'demand curve': guiding discussions on programmatic investments.

Science.gov (United States)

Weinberger, Michelle; Sonneveldt, Emily; Stover, John

2017-12-22

Most frameworks for family planning include both access and demand interventions. Understanding how these two are linked and when each should be prioritized is difficult. The maximum contraceptive prevalence 'demand curve' was created based on a relationship between the modern contraceptive prevalence rate (mCPR) and mean ideal number of children to allow for a quantitative assessment of the balance between access and demand interventions. The curve represents the maximum mCPR that is likely to be seen given fertility intentions and related norms and constructs that influence contraceptive use. The gap between a country's mCPR and this maximum is referred to as the 'potential use gap.' This concept can be used by countries to prioritize access investments where the gap is large, and discuss implications for future contraceptive use where the gap is small. It is also used within the FP Goals model to ensure mCPR growth from access interventions does not exceed available demand.

Maximum-likelihood estimation of recent shared ancestry (ERSA).

Science.gov (United States)

Huff, Chad D; Witherspoon, David J; Simonson, Tatum S; Xing, Jinchuan; Watkins, W Scott; Zhang, Yuhua; Tuohy, Therese M; Neklason, Deborah W; Burt, Randall W; Guthery, Stephen L; Woodward, Scott R; Jorde, Lynn B

2011-05-01

Accurate estimation of recent shared ancestry is important for genetics, evolution, medicine, conservation biology, and forensics. Established methods estimate kinship accurately for first-degree through third-degree relatives. We demonstrate that chromosomal segments shared by two individuals due to identity by descent (IBD) provide much additional information about shared ancestry. We developed a maximum-likelihood method for the estimation of recent shared ancestry (ERSA) from the number and lengths of IBD segments derived from high-density SNP or whole-genome sequence data. We used ERSA to estimate relationships from SNP genotypes in 169 individuals from three large, well-defined human pedigrees. ERSA is accurate to within one degree of relationship for 97% of first-degree through fifth-degree relatives and 80% of sixth-degree and seventh-degree relatives. We demonstrate that ERSA's statistical power approaches the maximum theoretical limit imposed by the fact that distant relatives frequently share no DNA through a common ancestor. ERSA greatly expands the range of relationships that can be estimated from genetic data and is implemented in a freely available software package.

Optimizing the maximum reported cluster size in the spatial scan statistic for ordinal data.

Science.gov (United States)

Kim, Sehwi; Jung, Inkyung

2017-01-01

The spatial scan statistic is an important tool for spatial cluster detection. There have been numerous studies on scanning window shapes. However, little research has been done on the maximum scanning window size or maximum reported cluster size. Recently, Han et al. proposed to use the Gini coefficient to optimize the maximum reported cluster size. However, the method has been developed and evaluated only for the Poisson model. We adopt the Gini coefficient to be applicable to the spatial scan statistic for ordinal data to determine the optimal maximum reported cluster size. Through a simulation study and application to a real data example, we evaluate the performance of the proposed approach. With some sophisticated modification, the Gini coefficient can be effectively employed for the ordinal model. The Gini coefficient most often picked the optimal maximum reported cluster sizes that were the same as or smaller than the true cluster sizes with very high accuracy. It seems that we can obtain a more refined collection of clusters by using the Gini coefficient. The Gini coefficient developed specifically for the ordinal model can be useful for optimizing the maximum reported cluster size for ordinal data and helpful for properly and informatively discovering cluster patterns.

Jarzynski equality in the context of maximum path entropy

Science.gov (United States)

González, Diego; Davis, Sergio

2017-06-01

In the global framework of finding an axiomatic derivation of nonequilibrium Statistical Mechanics from fundamental principles, such as the maximum path entropy - also known as Maximum Caliber principle -, this work proposes an alternative derivation of the well-known Jarzynski equality, a nonequilibrium identity of great importance today due to its applications to irreversible processes: biological systems (protein folding), mechanical systems, among others. This equality relates the free energy differences between two equilibrium thermodynamic states with the work performed when going between those states, through an average over a path ensemble. In this work the analysis of Jarzynski's equality will be performed using the formalism of inference over path space. This derivation highlights the wide generality of Jarzynski's original result, which could even be used in non-thermodynamical settings such as social systems, financial and ecological systems.

Maximum heat flux in boiling in a large volume

International Nuclear Information System (INIS)

Bergmans, Dzh.

1976-01-01

Relationships are derived for the maximum heat flux qsub(max) without basing on the assumptions of both the critical vapor velocity corresponding to the zero growth rate, and planar interface. The Helmholz nonstability analysis of vapor column has been made to this end. The results of this examination have been used to find maximum heat flux for spherical, cylindric and flat plate heaters. The conventional hydrodynamic theory was found to be incapable of producing a satisfactory explanation of qsub(max) for small heaters. The occurrence of qsub(max) in the present case can be explained by inadequate removal of vapor output from the heater (the force of gravity for cylindrical heaters and surface tension for the spherical ones). In case of flat plate heater the qsub(max) value can be explained with the help of the hydrodynamic theory

A Maximum Principle for SDEs of Mean-Field Type

Energy Technology Data Exchange (ETDEWEB)

Andersson, Daniel, E-mail: danieand@math.kth.se; Djehiche, Boualem, E-mail: boualem@math.kth.se [Royal Institute of Technology, Department of Mathematics (Sweden)

2011-06-15

We study the optimal control of a stochastic differential equation (SDE) of mean-field type, where the coefficients are allowed to depend on some functional of the law as well as the state of the process. Moreover the cost functional is also of mean-field type, which makes the control problem time inconsistent in the sense that the Bellman optimality principle does not hold. Under the assumption of a convex action space a maximum principle of local form is derived, specifying the necessary conditions for optimality. These are also shown to be sufficient under additional assumptions. This maximum principle differs from the classical one, where the adjoint equation is a linear backward SDE, since here the adjoint equation turns out to be a linear mean-field backward SDE. As an illustration, we apply the result to the mean-variance portfolio selection problem.

A Maximum Principle for SDEs of Mean-Field Type

International Nuclear Information System (INIS)

Andersson, Daniel; Djehiche, Boualem

2011-01-01

We study the optimal control of a stochastic differential equation (SDE) of mean-field type, where the coefficients are allowed to depend on some functional of the law as well as the state of the process. Moreover the cost functional is also of mean-field type, which makes the control problem time inconsistent in the sense that the Bellman optimality principle does not hold. Under the assumption of a convex action space a maximum principle of local form is derived, specifying the necessary conditions for optimality. These are also shown to be sufficient under additional assumptions. This maximum principle differs from the classical one, where the adjoint equation is a linear backward SDE, since here the adjoint equation turns out to be a linear mean-field backward SDE. As an illustration, we apply the result to the mean-variance portfolio selection problem.

Effect of Training Frequency on Maximum Expiratory Pressure

Science.gov (United States)

Anand, Supraja; El-Bashiti, Nour; Sapienza, Christine

2012-01-01

Purpose: To determine the effects of expiratory muscle strength training (EMST) frequency on maximum expiratory pressure (MEP). Method: We assigned 12 healthy participants to 2 groups of training frequency (3 days per week and 5 days per week). They completed a 4-week training program on an EMST trainer (Aspire Products, LLC). MEP was the primary…

Ethylene Production Maximum Achievable Control Technology (MACT) Compliance Manual

Science.gov (United States)

This July 2006 document is intended to help owners and operators of ethylene processes understand and comply with EPA's maximum achievable control technology standards promulgated on July 12, 2002, as amended on April 13, 2005 and April 20, 2006.

13 CFR 107.845 - Maximum rate of amortization on Loans and Debt Securities.

Science.gov (United States)

2010-01-01

... ADMINISTRATION SMALL BUSINESS INVESTMENT COMPANIES Financing of Small Businesses by Licensees Structuring Licensee's Financing of An Eligible Small Business: Terms and Conditions of Financing § 107.845 Maximum... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Maximum rate of amortization on...

Current opinion about maximum entropy methods in Moessbauer spectroscopy

International Nuclear Information System (INIS)

Szymanski, K

2009-01-01

Current opinion about Maximum Entropy Methods in Moessbauer Spectroscopy is presented. The most important advantage offered by the method is the correct data processing under circumstances of incomplete information. Disadvantage is the sophisticated algorithm and its application to the specific problems.

Bistability, non-ergodicity, and inhibition in pairwise maximum-entropy models.

Science.gov (United States)

Rostami, Vahid; Porta Mana, PierGianLuca; Grün, Sonja; Helias, Moritz

2017-10-01

Pairwise maximum-entropy models have been used in neuroscience to predict the activity of neuronal populations, given only the time-averaged correlations of the neuron activities. This paper provides evidence that the pairwise model, applied to experimental recordings, would produce a bimodal distribution for the population-averaged activity, and for some population sizes the second mode would peak at high activities, that experimentally would be equivalent to 90% of the neuron population active within time-windows of few milliseconds. Several problems are connected with this bimodality: 1. The presence of the high-activity mode is unrealistic in view of observed neuronal activity and on neurobiological grounds. 2. Boltzmann learning becomes non-ergodic, hence the pairwise maximum-entropy distribution cannot be found: in fact, Boltzmann learning would produce an incorrect distribution; similarly, common variants of mean-field approximations also produce an incorrect distribution. 3. The Glauber dynamics associated with the model is unrealistically bistable and cannot be used to generate realistic surrogate data. This bimodality problem is first demonstrated for an experimental dataset from 159 neurons in the motor cortex of macaque monkey. Evidence is then provided that this problem affects typical neural recordings of population sizes of a couple of hundreds or more neurons. The cause of the bimodality problem is identified as the inability of standard maximum-entropy distributions with a uniform reference measure to model neuronal inhibition. To eliminate this problem a modified maximum-entropy model is presented, which reflects a basic effect of inhibition in the form of a simple but non-uniform reference measure. This model does not lead to unrealistic bimodalities, can be found with Boltzmann learning, and has an associated Glauber dynamics which incorporates a minimal asymmetric inhibition.

Rate maximum calculation of Dpa in CNA-II pressure vessel

International Nuclear Information System (INIS)

Mascitti, J. A

2012-01-01

The maximum dpa rate was calculated for the reactor in the following state: fresh fuel, no Xenon, a Boron concentration of 15.3 ppm, critical state, its control rods in the criticality position, hot, at full power (2160 MW). It was determined that the maximum dpa rate under such conditions is 3.54(2)x10 12 s -1 and it is located in the positions corresponding to θ=210 o in the azimuthal direction, and z=20 cm and -60 cm respectively in the axial direction, considering the calculation mesh centered at half height of the fuel element (FE) active length. The dpa rate spectrum was determined as well as the contribution to it for 4 energy groups: a thermal group, two epithermal groups and a fast one. The maximum dpa rate considering the photo-neutrons production from (γ, n) reaction in the heavy water of coolant and moderator was 3.93(4)x10 12 s -1 that is 11% greater than the obtained without photo-neutrons. This verified significant difference between both cases, suggest that photo-neutrons in large heavy water reactors such as CNA-II should not be ignored. The maximum DPA rate in the first mm of the reactor pressure vessel was calculated too and it was obtained a value of 4.22(6)x10 12 s -1 . It should be added that the calculation was carried out with the reactor complete accurate model, with no approximations in spatial or energy variables. Each value has, between parentheses, a percentage relative error representing the statistical uncertainty due to the probabilistic Monte Carlo method used to estimate it. More representative values may be obtained with this method if equilibrium burn-up distribution is used (author)

Probable Maximum Earthquake Magnitudes for the Cascadia Subduction

Science.gov (United States)

Rong, Y.; Jackson, D. D.; Magistrale, H.; Goldfinger, C.

2013-12-01

The concept of maximum earthquake magnitude (mx) is widely used in seismic hazard and risk analysis. However, absolute mx lacks a precise definition and cannot be determined from a finite earthquake history. The surprising magnitudes of the 2004 Sumatra and the 2011 Tohoku earthquakes showed that most methods for estimating mx underestimate the true maximum if it exists. Thus, we introduced the alternate concept of mp(T), probable maximum magnitude within a time interval T. The mp(T) can be solved using theoretical magnitude-frequency distributions such as Tapered Gutenberg-Richter (TGR) distribution. The two TGR parameters, β-value (which equals 2/3 b-value in the GR distribution) and corner magnitude (mc), can be obtained by applying maximum likelihood method to earthquake catalogs with additional constraint from tectonic moment rate. Here, we integrate the paleoseismic data in the Cascadia subduction zone to estimate mp. The Cascadia subduction zone has been seismically quiescent since at least 1900. Fortunately, turbidite studies have unearthed a 10,000 year record of great earthquakes along the subduction zone. We thoroughly investigate the earthquake magnitude-frequency distribution of the region by combining instrumental and paleoseismic data, and using the tectonic moment rate information. To use the paleoseismic data, we first estimate event magnitudes, which we achieve by using the time interval between events, rupture extent of the events, and turbidite thickness. We estimate three sets of TGR parameters: for the first two sets, we consider a geographically large Cascadia region that includes the subduction zone, and the Explorer, Juan de Fuca, and Gorda plates; for the third set, we consider a narrow geographic region straddling the subduction zone. In the first set, the β-value is derived using the GCMT catalog. In the second and third sets, the β-value is derived using both the GCMT and paleoseismic data. Next, we calculate the corresponding mc

The Structure of the Class of Maximum Tsallis–Havrda–Chavát Entropy Copulas

Directory of Open Access Journals (Sweden)

Jesús E. García

2016-07-01

Full Text Available A maximum entropy copula is the copula associated with the joint distribution, with prescribed marginal distributions on [ 0 , 1 ] , which maximizes the Tsallis–Havrda–Chavát entropy with q = 2 . We find necessary and sufficient conditions for each maximum entropy copula to be a copula in the class introduced in Rodríguez-Lallena and Úbeda-Flores (2004, and we also show that each copula in that class is a maximum entropy copula.

Optimum detection for extracting maximum information from symmetric qubit sets

International Nuclear Information System (INIS)

Mizuno, Jun; Fujiwara, Mikio; Sasaki, Masahide; Akiba, Makoto; Kawanishi, Tetsuya; Barnett, Stephen M.

2002-01-01

We demonstrate a class of optimum detection strategies for extracting the maximum information from sets of equiprobable real symmetric qubit states of a single photon. These optimum strategies have been predicted by Sasaki et al. [Phys. Rev. A 59, 3325 (1999)]. The peculiar aspect is that the detections with at least three outputs suffice for optimum extraction of information regardless of the number of signal elements. The cases of ternary (or trine), quinary, and septenary polarization signals are studied where a standard von Neumann detection (a projection onto a binary orthogonal basis) fails to access the maximum information. Our experiments demonstrate that it is possible with present technologies to attain about 96% of the theoretical limit

Study of the chemisorption and hydrogenation of propylene on platinum by temperature-programed desorption

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, S.; Nakamura, M.; Yoshioka, N.

1978-01-01

Temperature-programed desorption (TPD) chromotograms of propylene adsorbed on platinum black in the absence or presence of hydrogen preadsorbed, admitted simultaneously, or admitted later, all showed four peaks at about 260/sup 0/ (A), 380/sup 0/ (B), 570/sup 0/ (C), and higher than 720/sup 0/K (D). Peaks A and B were identified as mixtures of propylene and propane, and peaks C and D were methane formed by thermal decomposition of the chemisorbed propylene during desorption. When nitrogen rather than helium was used as the carrier gas for the TPD, only delta-hydrogen was observed; this suggested that propylene was more strongly adsorbed on the platinum than hydrogen. Studies of the reactivities with propylene of the various types of chemisorbed hydrogen previously detected by TPD showed that propylene reacted with ..gamma..-hydrogen present on the surface in the form of hydrogen atoms chemisorbed on top of platinum atoms and with ..beta..-hydrogen, molecular hydrogen chemisorbed in a bridged form, but did not react with delta-hydrogen. Tables and graph.

Ultrahigh-sensitive detection of molecules produced in catalytic reactions by uni-atomic-composition bi-element clusters supported on solid substrate

International Nuclear Information System (INIS)

Yasumatsu, H; Fukui, N

2013-01-01

An apparatus has been developed for measuring catalytic activities of uni-atomic-composition bi-element clusters supported on a solid substrate. The cluster sample is prepared by irradiating a cluster-ion beam having the uni-atomic composition onto the substrate on a soft-landing condition in an ultra-high vacuum. The catalytic activity is measured by temperature-programmed desorption (TPD) mass analysis. Molecules at a density as low as 3 cm −3 have been detected with an ultrahigh-sensitive TPD mass spectrometer consisting of a cylindrical electron gun, a quadrupole mass filter and a micro-channel-plate ion-detector. The high reproducibility has been achieved by careful calibration of the TPD mass spectrometer. As a benchmark example, thermal oxidation of CO catalysed on Pt 30 disks supported on a silicon surface was studied. The CO 2 products have been successfully observed at the Pt 30 density as low as 3 × 10 12 clusters in a circular area of 8 mm in diameter at the ramping rate of the sample temperature as low as 0.3 K s −1 .

Deep energetic trap states in organic photovoltaic devices

KAUST Repository

Shuttle, Christopher G.; Treat, Neil D.; Douglas, Jessica D.; Frechet, Jean; Chabinyc, Michael L.

2011-01-01

The nature of energetic disorder in organic semiconductors is poorly understood. In photovoltaics, energetic disorder leads to reductions in the open circuit voltage and contributes to other loss processes. In this work, three independent optoelectronic methods were used to determine the long-lived carrier populations in a high efficiency N-alkylthieno[3,4-c]pyrrole-4,6-dione (TPD) based polymer: fullerene solar cell. In the TPD co-polymer, all methods indicate the presence of a long-lived carrier population of ∼ 10 15 cm -3 on timescales ≤100 μs. Additionally, the behavior of these photovoltaic devices under optical bias is consistent with deep energetic lying trap states. Comparative measurements were also performed on high efficiency poly-3-hexylthiophene (P3HT): fullerene solar cells; however a similar long-lived carrier population was not observed. This observation is consistent with a higher acceptor concentration (doping) in P3HT than in the TPD-based copolymer. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Undoped and doped poly(tetraphenylbenzidine) as sensitive material for an impedimetric nitrogen dioxide gas dosimeter

Energy Technology Data Exchange (ETDEWEB)

Marr, I.; Moos, R., E-mail: functional.materials@uni-bayreuth.de [Department of Functional Materials, University of Bayreuth, Bayreuth 95440 (Germany); Neumann, K.; Thelakkat, M. [Department of Macromolecular Chemistry I, Applied Functional Polymers, University of Bayreuth, Bayreuth 95440 (Germany)

2014-09-29

This article presents a nitrogen dioxide (NO{sub 2}) detecting gas dosimeter based on poly(tetraphenylbenzidine) poly(TPD) as nitrogen oxide (NO{sub x}) sensitive layer. Gas dosimeters are suitable devices to determine reliably low levels of analytes over a long period of time. During NO{sub x} exposure, the analyte molecules are accumulated irreversibly in the sensing layer of the dosimeter enhancing the conductivity of the hole conducting poly(TPD), which can be measured by impedance spectroscopy. Due to their possibility for low cost production by simple printing techniques and very good physical, photochemical, and electrochemical properties, poly(TPD)s are suitable for application in gas dosimeters operated at room temperature. We studied the effect of doping with a Co(III)-complex in combination with a conducting salt on the dosimeter behavior. Compared to the undoped material, a strong influence of the doping can be observed: the conductivity of the sensing material increases significantly, the noise of the signal decreases and an unwanted recovery of the sensor signal can be prevented, leading to a NO{sub x} detection limit <10 ppm.

Contact engineering for efficient charge injection in organic transistors with low-cost metal electrodes

Science.gov (United States)

Panigrahi, D.; Kumar, S.; Dhar, A.

2017-10-01

Controlling charge injection at the metal-semiconductor interface is very crucial for organic electronic devices in general as it can significantly influence the overall device performance. Herein, we report a facile, yet efficient contact modification approach, to enhance the hole injection efficiency through the incorporation of a high vacuum deposited TPD [N,N'-Bis(3-methylphenyl)-N,N'-diphenylbenzidine] interlayer between the electrodes and the active semiconducting layer. The device performance parameters such as mobility and on/off ratio improved significantly after the inclusion of the TPD buffer layer, and more interestingly, the devices with cost effective Ag and Cu electrodes were able to exhibit a superior device performance than the typically used Au source-drain devices. We have also observed that this contact modification technique can be even more effective than commonly used metal oxide interface modifying layers. Our investigations demonstrate the efficacy of the TPD interlayer in effectively reducing the interfacial contact resistance through the modification of pentacene energy levels, which consequently results in the substantial improvement in the device performances.

Deep energetic trap states in organic photovoltaic devices

KAUST Repository

Shuttle, Christopher G.

2011-11-23

The nature of energetic disorder in organic semiconductors is poorly understood. In photovoltaics, energetic disorder leads to reductions in the open circuit voltage and contributes to other loss processes. In this work, three independent optoelectronic methods were used to determine the long-lived carrier populations in a high efficiency N-alkylthieno[3,4-c]pyrrole-4,6-dione (TPD) based polymer: fullerene solar cell. In the TPD co-polymer, all methods indicate the presence of a long-lived carrier population of ∼ 10 15 cm -3 on timescales ≤100 μs. Additionally, the behavior of these photovoltaic devices under optical bias is consistent with deep energetic lying trap states. Comparative measurements were also performed on high efficiency poly-3-hexylthiophene (P3HT): fullerene solar cells; however a similar long-lived carrier population was not observed. This observation is consistent with a higher acceptor concentration (doping) in P3HT than in the TPD-based copolymer. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Estimation of Maximum Allowable PV Connection to LV Residential Power Networks

DEFF Research Database (Denmark)

Demirok, Erhan; Sera, Dezso; Teodorescu, Remus

2011-01-01

Maximum photovoltaic (PV) hosting capacity of low voltage (LV) power networks is mainly restricted by either thermal limits of network components or grid voltage quality resulted from high penetration of distributed PV systems. This maximum hosting capacity may be lower than the available solar...... potential of geographic area due to power network limitations even though all rooftops are fully occupied with PV modules. Therefore, it becomes more of an issue to know what exactly limits higher PV penetration level and which solutions should be engaged efficiently such as over sizing distribution...

Maximum power operation of interacting molecular motors

DEFF Research Database (Denmark)

Golubeva, Natalia; Imparato, Alberto

2013-01-01

, as compared to the non-interacting system, in a wide range of biologically compatible scenarios. We furthermore consider the case where the motor-motor interaction directly affects the internal chemical cycle and investigate the effect on the system dynamics and thermodynamics.......We study the mechanical and thermodynamic properties of different traffic models for kinesin which are relevant in biological and experimental contexts. We find that motor-motor interactions play a fundamental role by enhancing the thermodynamic efficiency at maximum power of the motors...

Modelling non-stationary annual maximum flood heights in the lower Limpopo River basin of Mozambique

Directory of Open Access Journals (Sweden)

Daniel Maposa

2016-05-01

Full Text Available In this article we fit a time-dependent generalised extreme value (GEV distribution to annual maximum flood heights at three sites: Chokwe, Sicacate and Combomune in the lower Limpopo River basin of Mozambique. A GEV distribution is fitted to six annual maximum time series models at each site, namely: annual daily maximum (AM1, annual 2-day maximum (AM2, annual 5-day maximum (AM5, annual 7-day maximum (AM7, annual 10-day maximum (AM10 and annual 30-day maximum (AM30. Non-stationary time-dependent GEV models with a linear trend in location and scale parameters are considered in this study. The results show lack of sufficient evidence to indicate a linear trend in the location parameter at all three sites. On the other hand, the findings in this study reveal strong evidence of the existence of a linear trend in the scale parameter at Combomune and Sicacate, whilst the scale parameter had no significant linear trend at Chokwe. Further investigation in this study also reveals that the location parameter at Sicacate can be modelled by a nonlinear quadratic trend; however, the complexity of the overall model is not worthwhile in fit over a time-homogeneous model. This study shows the importance of extending the time-homogeneous GEV model to incorporate climate change factors such as trend in the lower Limpopo River basin, particularly in this era of global warming and a changing climate. Keywords: nonstationary extremes; annual maxima; lower Limpopo River; generalised extreme value

Maximum power point tracking for PV systems under partial shading conditions using current sweeping

International Nuclear Information System (INIS)

Tsang, K.M.; Chan, W.L.

2015-01-01

Highlights: • A novel approach for tracking the maximum power point of photovoltaic systems. • Able to handle both the uniform insolation and partial shading conditions. • Maximum power point tracking based on current sweeping. - Abstract: Partial shading on photovoltaic (PV) arrays causes multiple peaks on the output power–voltage characteristic curve and local searching technique such as perturb and observe (P&O) method could easily fail in searching for the global maximum. Moreover, existing global searching techniques are still not very satisfactory in terms of speed and implementation complexity. In this paper, a fast global maximum power point (MPPT) tracking method which is using current sweeping for photovoltaic arrays under partial shading conditions is proposed. Unlike conventional approach, the proposed method is current based rather than voltage based. The initial maximum power point will be derived based on a current sweeping test and the maximum power point can be enhanced by a finer local search. The speed of the global search is mainly governed by the apparent time constant of the PV array and the generation of a fast current sweeping test. The fast current sweeping test can easily be realized by a DC/DC boost converter with a very fast current control loop. Experimental results are included to demonstrate the effectiveness of the proposed global searching scheme

Impact of marine reserve on maximum sustainable yield in a traditional prey-predator system

Science.gov (United States)

Paul, Prosenjit; Kar, T. K.; Ghorai, Abhijit

2018-01-01

Multispecies fisheries management requires managers to consider the impact of fishing activities on several species as fishing impacts both targeted and non-targeted species directly or indirectly in several ways. The intended goal of traditional fisheries management is to achieve maximum sustainable yield (MSY) from the targeted species, which on many occasions affect the targeted species as well as the entire ecosystem. Marine reserves are often acclaimed as the marine ecosystem management tool. Few attempts have been made to generalize the ecological effects of marine reserve on MSY policy. We examine here how MSY and population level in a prey-predator system are affected by the low, medium and high reserve size under different possible scenarios. Our simulation works shows that low reserve area, the value of MSY for prey exploitation is maximum when both prey and predator species have fast movement rate. For medium reserve size, our analysis revealed that the maximum value of MSY for prey exploitation is obtained when prey population has fast movement rate and predator population has slow movement rate. For high reserve area, the maximum value of MSY for prey's exploitation is very low compared to the maximum value of MSY for prey's exploitation in case of low and medium reserve. On the other hand, for low and medium reserve area, MSY for predator exploitation is maximum when both the species have fast movement rate.

A practical exact maximum compatibility algorithm for reconstruction of recent evolutionary history

OpenAIRE

Cherry, Joshua L.

2017-01-01

Background Maximum compatibility is a method of phylogenetic reconstruction that is seldom applied to molecular sequences. It may be ideal for certain applications, such as reconstructing phylogenies of closely-related bacteria on the basis of whole-genome sequencing. Results Here I present an algorithm that rapidly computes phylogenies according to a compatibility criterion. Although based on solutions to the maximum clique problem, this algorithm deals properly with ambiguities in the data....

Maximum Power Point Tracking Based on Sliding Mode Control

Directory of Open Access Journals (Sweden)

Nimrod Vázquez

2015-01-01

Full Text Available Solar panels, which have become a good choice, are used to generate and supply electricity in commercial and residential applications. This generated power starts with the solar cells, which have a complex relationship between solar irradiation, temperature, and output power. For this reason a tracking of the maximum power point is required. Traditionally, this has been made by considering just current and voltage conditions at the photovoltaic panel; however, temperature also influences the process. In this paper the voltage, current, and temperature in the PV system are considered to be a part of a sliding surface for the proposed maximum power point tracking; this means a sliding mode controller is applied. Obtained results gave a good dynamic response, as a difference from traditional schemes, which are only based on computational algorithms. A traditional algorithm based on MPPT was added in order to assure a low steady state error.

Measurement and estimation of maximum skin dose to the patient for different interventional procedures

International Nuclear Information System (INIS)

Cheng Yuxi; Liu Lantao; Wei Kedao; Yu Peng; Yan Shulin; Li Tianchang

2005-01-01

Objective: To determine the dose distribution and maximum skin dose to the patient for four interventional procedures: coronary angiography (CA), hepatic angiography (HA), radiofrequency ablation (RF) and cerebral angiography (CAG), and to estimate the definitive effect of radiation on skin. Methods: Skin dose was measured using LiF: Mg, Cu, P TLD chips. A total of 9 measuring points were chosen on the back of the patient with two TLDs placed at each point, for CA, HA and RF interventional procedures, whereas two TLDs were placed on one point each at the postero-anterior (PA) and lateral side (LAT) respectively, during the CAG procedure. Results: The results revealed that the maximum skin dose to the patient was 1683.91 mGy for the HA procedure with a mean value of 607.29 mGy. The maximum skin dose at the PA point was 959.3 mGy for the CAG with a mean value of 418.79 mGy; While the maximum and the mean doses at the LAT point were 704 mGy and 191.52 mGy, respectively. For the RF procedure the maximum dose was 853.82 mGy and the mean was 219.67 mGy. For the CA procedure the maximum dose was 456.1 mGy and the mean was 227.63 mGy. Conclusion: All the measured dose values in this study are estimated ones which could not provide the accurate maximum value because it is difficult to measure using a great deal of TLDs. On the other hand, the small area of skin exposed to high dose could be missed as the distribution of the dose is successive. (authors)

Water Quality Assessment and Total Maximum Daily Loads Information (ATTAINS)

Data.gov (United States)

U.S. Environmental Protection Agency — The Water Quality Assessment TMDL Tracking And Implementation System (ATTAINS) stores and tracks state water quality assessment decisions, Total Maximum Daily Loads...

STUDY ON MAXIMUM SPECIFIC SLUDGE ACIVITY OF DIFFERENT ANAEROBIC GRANULAR SLUDGE BY BATCH TESTS

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The maximum specific sludge activity of granular sludge from large-scale UASB, IC and Biobed anaerobic reactors were investigated by batch tests. The limitation factors related to maximum specific sludge activity (diffusion, substrate sort, substrate concentration and granular size) were studied. The general principle and procedure for the precise measurement of maximum specific sludge activity were suggested. The potential capacity of loading rate of the IC and Biobed anaerobic reactors were analyzed and compared by use of the batch tests results.

Influence of aliphatic amides on the temperature of maximum density of water

International Nuclear Information System (INIS)

Torres, Andrés Felipe; Romero, Carmen M.

2017-01-01

Highlights: • The addition of amides decreases the temperature of maximum density of water suggesting a disruptive effect on water structure. • The amides in aqueous solution do not follow the Despretz equation in the concentration range considered. • The temperature shift Δθ as a function of molality is represented by a second order equation. • The Despretz constants were determined considering the dilute concentration region for each amide solution. • Solute disrupting effect of amides becomes smaller as its hydrophobic character increases. - Abstract: The influence of dissolved substances on the temperature of the maximum density of water has been studied in relation to their effect on water structure as they can change the equilibrium between structured and unstructured species of water. However, most work has been performed using salts and the studies with small organic solutes such as amides are scarce. In this work, the effect of acetamide, propionamide and butyramide on the temperature of maximum density of water was determined from density measurements using a magnetic float densimeter. Densities of aqueous solutions were measured within the temperature range from T = (275.65–278.65) K at intervals of 0.50 K in the concentration range between (0.10000 and 0.80000) mol·kg −1 . The temperature of maximum density was determined from the experimental results. The effect of the three amides is to decrease the temperature of maximum density of water and the change does not follow the Despretz equation. The results are discussed in terms of solute-water interactions and the disrupting effect of amides on water structure.

On minimizing the maximum broadcast decoding delay for instantly decodable network coding

KAUST Repository

Douik, Ahmed S.

2014-09-01

In this paper, we consider the problem of minimizing the maximum broadcast decoding delay experienced by all the receivers of generalized instantly decodable network coding (IDNC). Unlike the sum decoding delay, the maximum decoding delay as a definition of delay for IDNC allows a more equitable distribution of the delays between the different receivers and thus a better Quality of Service (QoS). In order to solve this problem, we first derive the expressions for the probability distributions of maximum decoding delay increments. Given these expressions, we formulate the problem as a maximum weight clique problem in the IDNC graph. Although this problem is known to be NP-hard, we design a greedy algorithm to perform effective packet selection. Through extensive simulations, we compare the sum decoding delay and the max decoding delay experienced when applying the policies to minimize the sum decoding delay and our policy to reduce the max decoding delay. Simulations results show that our policy gives a good agreement among all the delay aspects in all situations and outperforms the sum decoding delay policy to effectively minimize the sum decoding delay when the channel conditions become harsher. They also show that our definition of delay significantly improve the number of served receivers when they are subject to strict delay constraints.

Psychophysical basis for maximum pushing and pulling forces: A review and recommendations.

Science.gov (United States)

Garg, Arun; Waters, Thomas; Kapellusch, Jay; Karwowski, Waldemar

2014-03-01

The objective of this paper was to perform a comprehensive review of psychophysically determined maximum acceptable pushing and pulling forces. Factors affecting pushing and pulling forces are identified and discussed. Recent studies show a significant decrease (compared to previous studies) in maximum acceptable forces for males but not for females when pushing and pulling on a treadmill. A comparison of pushing and pulling forces measured using a high inertia cart with those measured on a treadmill shows that the pushing and pulling forces using high inertia cart are higher for males but are about the same for females. It is concluded that the recommendations of Snook and Ciriello (1991) for pushing and pulling forces are still valid and provide reasonable recommendations for ergonomics practitioners. Regression equations as a function of handle height, frequency of exertion and pushing/pulling distance are provided to estimate maximum initial and sustained forces for pushing and pulling acceptable to 75% male and female workers. At present it is not clear whether pushing or pulling should be favored. Similarly, it is not clear what handle heights would be optimal for pushing and pulling. Epidemiological studies are needed to determine relationships between psychophysically determined maximum acceptable pushing and pulling forces and risk of musculoskeletal injuries, in particular to low back and shoulders.

Smart Global Maximum Power Point Tracking Controller of Photovoltaic Module Arrays

Directory of Open Access Journals (Sweden)

Long-Yi Chang

2018-03-01

Full Text Available This study first explored the effect of shading on the output characteristics of modules in a photovoltaic module array. Next, a modified particle swarm optimization (PSO method was employed to track the maximum power point of the multiple-peak characteristic curve of the array. Through the optimization method, the weighting value and cognition learning factor decreased with an increasing number of iterations, whereas the social learning factor increased, thereby enhancing the tracking capability of a maximum power point tracker. In addition, the weighting value was slightly modified on the basis of the changes in the slope and power of the characteristic curve to increase the tracking speed and stability of the tracker. Finally, a PIC18F8720 microcontroller was coordinated with peripheral hardware circuits to realize the proposed PSO method, which was then adopted to track the maximum power point of the power–voltage (P–V output characteristic curve of the photovoltaic module array under shading. Subsequently, tests were conducted to verify that the modified PSO method exhibited favorable tracking speed and accuracy.

Image coding based on maximum entropy partitioning for identifying ...

Indian Academy of Sciences (India)

A new coding scheme based on maximum entropy partitioning is proposed in our work, particularly to identify the improbable intensities related to different emotions. The improbable intensities when used as a mask decode the facial expression correctly, providing an effectiveplatform for future emotion categorization ...

Distribution of phytoplankton groups within the deep chlorophyll maximum

KAUST Repository

Latasa, Mikel; Cabello, Ana Marí a; Moran, Xose Anxelu G.; Massana, Ramon; Scharek, Renate

2016-01-01

and optical and FISH microscopy. All groups presented minimum abundances at the surface and a maximum in the DCM layer. The cell distribution was not vertically symmetrical around the DCM peak and cells tended to accumulate in the upper part of the DCM layer

Inverse feasibility problems of the inverse maximum flow problems

Indian Academy of Sciences (India)

199–209. c Indian Academy of Sciences. Inverse feasibility problems of the inverse maximum flow problems. ADRIAN DEACONU. ∗ and ELEONOR CIUREA. Department of Mathematics and Computer Science, Faculty of Mathematics and Informatics, Transilvania University of Brasov, Brasov, Iuliu Maniu st. 50,. Romania.

Combining Experiments and Simulations Using the Maximum Entropy Principle

DEFF Research Database (Denmark)

Boomsma, Wouter; Ferkinghoff-Borg, Jesper; Lindorff-Larsen, Kresten

2014-01-01

in the context of a simple example, after which we proceed with a real-world application in the field of molecular simulations, where the maximum entropy procedure has recently provided new insight. Given the limited accuracy of force fields, macromolecular simulations sometimes produce results...

Impact of the Nature of the Side-Chains on the Polymer-Fullerene Packing in the Mixed Regions of Bulk Heterojunction Solar Cells

KAUST Repository

Wang, Tonghui; Ravva, Mahesh Kumar; Bredas, Jean-Luc

2016-01-01

Polymer-fullerene packing in mixed regions of a bulk heterojunction solar cell is expected to play a major role in exciton-dissociation, charge-separation, and charge-recombination processes. Here, molecular dynamics simulations are combined with density functional theory calculations to examine the impact of nature and location of polymer side-chains on the polymer-fullerene packing in mixed regions. The focus is on poly-benzo[1,2-b:4,5-b′]dithiophene-thieno[3,4-c]pyrrole-4,6-dione (PBDTTPD) as electron-donating material and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) as electron-accepting material. Three polymer side-chain patterns are considered: i) linear side-chains on both benzodithiophene (BDT) and thienopyrroledione (TPD) moieties; ii) two linear side-chains on BDT and a branched side-chain on TPD; and iii) two branched side-chains on BDT and a linear side-chain on TPD. Increasing the number of branched side-chains is found to decrease the polymer packing density and thereby to enhance PBDTTPD–PC61 BM mixing. The nature and location of side-chains are found to play a determining role in the probability of finding PC61BM molecules close to either BDT or TPD. The electronic couplings relevant for the exciton-dissociation and charge-recombination processes are also evaluated. Overall, the findings are consistent with the experimental evolution of the PBDTTPD–PC61BM solar-cell performance as a function of side-chain patterns. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim