Effects of loading and size on maximum power output and gait characteristics in geckos.
Irschick, Duncan J; Vanhooydonck, Bieke; Herrel, Anthony; Andronescu, Anemone
2003-11-01
Stride length, stride frequency and power output are all factors influencing locomotor performance. Here, we first test whether mass-specific power output limits climbing performance in two species of geckos (Hemidactylus garnoti and Gekko gecko) by adding external loads to their bodies. We then test whether body size has a negative effect on mass-specific power output. Finally, we test whether loading affects kinematics in both gecko species. Lizards were induced to run vertically on a smooth wooden surface with loads of 0-200% of body mass (BM) in H. garnoti and 0-100% BM in G. gecko. For each stride, we calculated angular and linear kinematics (e.g. trunk angle, stride length), performance (maximum speed) and mean mass-specific power output per stride. The addition of increasingly large loads caused an initial increase in maximum mass-specific power output in both species, but for H. garnoti, mass-specific power output remained constant at higher loads (150% and 200% BM), even though maximum velocity declined. This result, in combination with the fact that stride frequency showed no evidence of leveling off as speed increased in either species, suggests that power limits maximum speed. In addition, the large gecko (G. gecko) produced significantly less power than the smaller H. garnoti, despite the fact that both species ran at similar speeds. This difference disappeared, however, when we recalculated power output based on higher maximum speeds for unloaded G. gecko moving vertically obtained by other researchers. Finally, the addition of external loads did not affect speed modulation in either species: both G. gecko and H. garnoti increase speed primarily by increasing stride frequency, regardless of loading condition. For a given speed, both species take shorter but more strides with heavier loads, but for a given load, G. gecko attains similar speeds to H. garnoti by taking longer but fewer strides.
Impact of DG Configuration on Maximum Use of Load Supply Capability in Distribution Power Systems
Hong Liu
2014-01-01
Full Text Available Traditional distributed generators (DGs planning methods take network loss minimization as the main objective to optimize DG sites in feeders. The use of load supply capability (LSC in DG planning will precisely answer the questions how many DGs should be integrated, which transformer they should be connected to, and which type of DGs should be adopted. The main work of this paper is to analyze the impact of DGs on LSC so as to answer the three key questions. It resolves the planning problem through three steps: (i two LSC models considering DGs’ access are developed, in which two different transfer strategies are considered: direct load transfer and indirect load transfer; (ii the method of combined simple method and point estimate method is proposed. At last, based on a base case, when the configuration of DGs is changing, the impact of DGs on system LSC is studied. After the case study, the conclusion concerning the impact of load transfer strategy, DG capacities, and DG types on LSC is reached.
Analysis of Photovoltaic Maximum Power Point Trackers
Veerachary, Mummadi
The photovoltaic generator exhibits a non-linear i-v characteristic and its maximum power point (MPP) varies with solar insolation. An intermediate switch-mode dc-dc converter is required to extract maximum power from the photovoltaic array. In this paper buck, boost and buck-boost topologies are considered and a detailed mathematical analysis, both for continuous and discontinuous inductor current operation, is given for MPP operation. The conditions on the connected load values and duty ratio are derived for achieving the satisfactory maximum power point operation. Further, it is shown that certain load values, falling out of the optimal range, will drive the operating point away from the true maximum power point. Detailed comparison of various topologies for MPPT is given. Selection of the converter topology for a given loading is discussed. Detailed discussion on circuit-oriented model development is given and then MPPT effectiveness of various converter systems is verified through simulations. Proposed theory and analysis is validated through experimental investigations.
Maximum Power from a Solar Panel
Michael Miller
2010-01-01
Full Text Available Solar energy has become a promising alternative to conventional fossil fuel sources. Solar panels are used to collect solar radiation and convert it into electricity. One of the techniques used to maximize the effectiveness of this energy alternative is to maximize the power output of the solar collector. In this project the maximum power is calculated by determining the voltage and the current of maximum power. These quantities are determined by finding the maximum value for the equation for power using differentiation. After the maximum values are found for each time of day, each individual quantity, voltage of maximum power, current of maximum power, and maximum power is plotted as a function of the time of day.
High Power Disk Loaded Guide Load
Farkas, Z.D.; /SLAC
2006-02-22
A method to design a matching section from a smooth guide to a disk-loaded guide, using a variation of broadband matching, [1, 2] is described. Using this method, we show how to design high power loads. The load consists of a disk-loaded coaxial guide operating in the TE{sub 01}-mode. We use this mode because it has no electric field terminating on a conductor, has no axial currents, and has no current at the cylinder-disk interface. A high power load design that has -35 dB reflection and a 200 MHz, -20 dB bandwidth, is presented. It is expected that it will carry the 600 MW output peak power of the pulse compression network. We use coaxial geometry and stainless steel material to increase the attenuation per cell.
Efficiency at maximum power of thermally coupled heat engines.
Apertet, Y; Ouerdane, H; Goupil, C; Lecoeur, Ph
2012-04-01
We study the efficiency at maximum power of two coupled heat engines, using thermoelectric generators (TEGs) as engines. Assuming that the heat and electric charge fluxes in the TEGs are strongly coupled, we simulate numerically the dependence of the behavior of the global system on the electrical load resistance of each generator in order to obtain the working condition that permits maximization of the output power. It turns out that this condition is not unique. We derive a simple analytic expression giving the relation between the electrical load resistance of each generator permitting output power maximization. We then focus on the efficiency at maximum power (EMP) of the whole system to demonstrate that the Curzon-Ahlborn efficiency may not always be recovered: The EMP varies with the specific working conditions of each generator but remains in the range predicted by irreversible thermodynamics theory. We discuss our results in light of nonideal Carnot engine behavior.
Solar Panel Maximum Power Point Tracker for Power Utilities
Sandeep Banik,
2014-01-01
Full Text Available ―Solar Panel Maximum Power Point Tracker For power utilities‖ As the name implied, it is a photovoltaic system that uses the photovoltaic array as a source of electrical power supply and since every photovoltaic (PV array has an optimum operating point, called the maximum power point, which varies depending on the insolation level and array voltage. A maximum power point tracker (MPPT is needed to operate the PV array at its maximum power point. The objective of this thesis project is to build a photovoltaic (PV array Of 121.6V DC Voltage(6 cell each 20V, 100watt And convert the DC voltage to Single phase 120v,50Hz AC voltage by switch mode power converter‘s and inverter‘s.
Maximum holding endurance time: Effects of load and load's center of gravity height.
Lee, Tzu-Hsien
2015-01-01
Manual holding task is a potential risk to the development of musculoskeletal injuries since it is prone to induce localized muscle fatigue. Maximum holding endurance time is a significant parameter for the design of manual holding task. This study aimed to examine the effects of load and load's COG height on maximum holding endurance time. Fifteen young and healthy males were recruited as participants. A factorial design was used to examine the effects of load and load's COG height on maximum holding endurance time. Four levels of load (15% , 30% , 45% and 60% of the participant's maximum holding capacity) and two levels of load's COG height in box (0 cm and 40 cm high from the handle position) were examined. Maximum holding endurance time decreased with increasing load and/or increasing load's COG height. The effect of load's COG height on maximum holding endurance time decreased with increasing load. Load, load's COG height, and the interaction of load and load's COG height significantly affected maximum holding endurance time. Practitioners should realize the effects of load, load's COG height, and the interaction of load and load's COG height on maximum holding endurance time when setting the working conditions of holding tasks.
Individual Module Maximum Power Point Tracking for Thermoelectric Generator Systems
Vadstrup, Casper; Schaltz, Erik; Chen, Min
2013-07-01
In a thermoelectric generator (TEG) system the DC/DC converter is under the control of a maximum power point tracker which ensures that the TEG system outputs the maximum possible power to the load. However, if the conditions, e.g., temperature, health, etc., of the TEG modules are different, each TEG module will not produce its maximum power. If each TEG module is controlled individually, each TEG module can be operated at its maximum power point and the TEG system output power will therefore be higher. In this work a power converter based on noninverting buck-boost converters capable of handling four TEG modules is presented. It is shown that, when each module in the TEG system is operated under individual maximum power point tracking, the system output power for this specific application can be increased by up to 8.4% relative to the situation when the modules are connected in series and 16.7% relative to the situation when the modules are connected in parallel.
Invulnerability of power grids based on maximum flow theory
Fan, Wenli; Huang, Shaowei; Mei, Shengwei
2016-11-01
The invulnerability analysis against cascades is of great significance in evaluating the reliability of power systems. In this paper, we propose a novel cascading failure model based on the maximum flow theory to analyze the invulnerability of power grids. In the model, node initial loads are built on the feasible flows of nodes with a tunable parameter γ used to control the initial node load distribution. The simulation results show that both the invulnerability against cascades and the tolerance parameter threshold αT are affected by node load distribution greatly. As γ grows, the invulnerability shows the distinct change rules under different attack strategies and different tolerance parameters α respectively. These results are useful in power grid planning and cascading failure prevention.
Zipf's law, power laws and maximum entropy
Visser, Matt
2013-04-01
Zipf's law, and power laws in general, have attracted and continue to attract considerable attention in a wide variety of disciplines—from astronomy to demographics to software structure to economics to linguistics to zoology, and even warfare. A recent model of random group formation (RGF) attempts a general explanation of such phenomena based on Jaynes' notion of maximum entropy applied to a particular choice of cost function. In the present paper I argue that the specific cost function used in the RGF model is in fact unnecessarily complicated, and that power laws can be obtained in a much simpler way by applying maximum entropy ideas directly to the Shannon entropy subject only to a single constraint: that the average of the logarithm of the observable quantity is specified.
Zipf's law, power laws, and maximum entropy
Visser, Matt
2012-01-01
Zipf's law, and power laws in general, have attracted and continue to attract considerable attention in a wide variety of disciplines - from astronomy to demographics to economics to linguistics to zoology, and even warfare. A recent model of random group formation [RGF] attempts a general explanation of such phenomena based on Jaynes' notion of maximum entropy applied to a particular choice of cost function. In the present article I argue that the cost function used in the RGF model is in fact unnecessarily complicated, and that power laws can be obtained in a much simpler way by applying maximum entropy ideas directly to the Shannon entropy subject only to a single constraint: that the average of the logarithm of the observable quantity is specified.
Water Quality Assessment and Total Maximum Daily Loads Information (ATTAINS)
U.S. Environmental Protection Agency — The Water Quality Assessment TMDL Tracking And Implementation System (ATTAINS) stores and tracks state water quality assessment decisions, Total Maximum Daily Loads...
Environmental Monitoring, Water Quality - Total Maximum Daily Load (TMDL)
NSGIC GIS Inventory (aka Ramona) — The Clean Water Act Section 303(d) establishes the Total Maximum Daily Load (TMDL) program. The purpose of the TMDL program is to identify sources of pollution and...
Environmental Monitoring, Water Quality - Total Maximum Daily Load (TMDL)
NSGIC Education | GIS Inventory — The Clean Water Act Section 303(d) establishes the Total Maximum Daily Load (TMDL) program. The purpose of the TMDL program is to identify sources of pollution and...
黄建明; 吴春华; 徐坤; 付立
2012-01-01
The operation principle of photovoltaic optimizer system and the essence of maximum power point tracking (MPPT) are introduced. Each PV module adopts MPPT control algorithm in photovoltaic optimizer system, which leads to wrong judgment of the traditional MPPT method due to the load impedance perturbation. Based on the equivalent load impedance perturbation, the distributed maximum power point tracking (DMPPT) is proposed to solve the problem. Considering the disturbance of control variables and load impedance to track MPP, the interaction between individual modules in the photovoltaic optimizer system is avoided. Finally, comparative experiments prove that the DMPPT method based on the equivalent load impedance perturbation proposed in this paper has the advantage of quick response and perturbation resistance to load impedance. Furthermore, the stability of this method is better than conventional MPPT method.%介绍了光伏优化器系统的工作原理及最大功率点跟踪的本质.针对光伏优化器系统中每块光伏组件进行MPPT控制,造成传统MPPT方法由于负载阻抗扰动而引起误判断的问题,提出了一种基于等效负载阻抗扰动的分布式最大功率点跟踪方法.该方法综合考虑控制量扰动和负载阻抗扰动进行MPPT判断,避免光伏优化器系统中各个独立模块之间的相互影响.通过对比实验证明提出的基于等效负载阻抗扰动的最大功率点跟踪方法具有快速的响应能力及抗负载阻抗扰动能力,其稳定性优于传统的MPPT方法.
Maximum Power Point Tracking of Photovoltaic System Using Intelligent Controller
Swathy C.S
2013-04-01
Full Text Available Photovoltaic systems normally use a maximum power point tracking (MPPT technique to continuously give forth the highest probable power to the load when the temperature and solar irradiationchanges occur. This subdues the problem of mismatch between the given load and the solar array. The energy conservation principle is used to obtain small signal model and transfer function. A simulationwork handling with MPPT controller, a DC/DC boost converter feeding a load is achieved. PI controller and fuzzy logic controllers were used as the MPPT controller, which controls the dc/dc converter. Simulations and experimental results showed excellent performance and were used for comparing PI controller and fuzzy logic controller.
Maximum Safety Regenerative Power Tracking for DC Traction Power Systems
Guifu Du
2017-02-01
Full Text Available Direct current (DC traction power systems are widely used in metro transport systems, with running rails usually being used as return conductors. When traction current flows through the running rails, a potential voltage known as “rail potential” is generated between the rails and ground. Currently, abnormal rises of rail potential exist in many railway lines during the operation of railway systems. Excessively high rail potentials pose a threat to human life and to devices connected to the rails. In this paper, the effect of regenerative power distribution on rail potential is analyzed. Maximum safety regenerative power tracking is proposed for the control of maximum absolute rail potential and energy consumption during the operation of DC traction power systems. The dwell time of multiple trains at each station and the trigger voltage of the regenerative energy absorbing device (READ are optimized based on an improved particle swarm optimization (PSO algorithm to manage the distribution of regenerative power. In this way, the maximum absolute rail potential and energy consumption of DC traction power systems can be reduced. The operation data of Guangzhou Metro Line 2 are used in the simulations, and the results show that the scheme can reduce the maximum absolute rail potential and energy consumption effectively and guarantee the safety in energy saving of DC traction power systems.
Maximum power operation of interacting molecular motors
Golubeva, Natalia; Imparato, Alberto
2013-01-01
We study the mechanical and thermodynamic properties of different traffic models for kinesin which are relevant in biological and experimental contexts. We find that motor-motor interactions play a fundamental role by enhancing the thermodynamic efficiency at maximum power of the motors......, as compared to the non-interacting system, in a wide range of biologically compatible scenarios. We furthermore consider the case where the motor-motor interaction directly affects the internal chemical cycle and investigate the effect on the system dynamics and thermodynamics....
A maximum power point tracking algorithm for photovoltaic applications
Nelatury, Sudarshan R.; Gray, Robert
2013-05-01
The voltage and current characteristic of a photovoltaic (PV) cell is highly nonlinear and operating a PV cell for maximum power transfer has been a challenge for a long time. Several techniques have been proposed to estimate and track the maximum power point (MPP) in order to improve the overall efficiency of a PV panel. A strategic use of the mean value theorem permits obtaining an analytical expression for a point that lies in a close neighborhood of the true MPP. But hitherto, an exact solution in closed form for the MPP is not published. This problem can be formulated analytically as a constrained optimization, which can be solved using the Lagrange method. This method results in a system of simultaneous nonlinear equations. Solving them directly is quite difficult. However, we can employ a recursive algorithm to yield a reasonably good solution. In graphical terms, suppose the voltage current characteristic and the constant power contours are plotted on the same voltage current plane, the point of tangency between the device characteristic and the constant power contours is the sought for MPP. It is subject to change with the incident irradiation and temperature and hence the algorithm that attempts to maintain the MPP should be adaptive in nature and is supposed to have fast convergence and the least misadjustment. There are two parts in its implementation. First, one needs to estimate the MPP. The second task is to have a DC-DC converter to match the given load to the MPP thus obtained. Availability of power electronics circuits made it possible to design efficient converters. In this paper although we do not show the results from a real circuit, we use MATLAB to obtain the MPP and a buck-boost converter to match the load. Under varying conditions of load resistance and irradiance we demonstrate MPP tracking in case of a commercially available solar panel MSX-60. The power electronics circuit is simulated by PSIM software.
An improved maximum power point tracking method for photovoltaic systems
Tafticht, T.; Agbossou, K.; Doumbia, M.L.; Cheriti, A. [Institut de recherche sur l' hydrogene, Departement de genie electrique et genie informatique, Universite du Quebec a Trois-Rivieres, C.P. 500, Trois-Rivieres (QC) (Canada)
2008-07-15
In most of the maximum power point tracking (MPPT) methods described currently in the literature, the optimal operation point of the photovoltaic (PV) systems is estimated by linear approximations. However these approximations can lead to less than optimal operating conditions and hence reduce considerably the performances of the PV system. This paper proposes a new approach to determine the maximum power point (MPP) based on measurements of the open-circuit voltage of the PV modules, and a nonlinear expression for the optimal operating voltage is developed based on this open-circuit voltage. The approach is thus a combination of the nonlinear and perturbation and observation (P and O) methods. The experimental results show that the approach improves clearly the tracking efficiency of the maximum power available at the output of the PV modules. The new method reduces the oscillations around the MPP, and increases the average efficiency of the MPPT obtained. The new MPPT method will deliver more power to any generic load or energy storage media. (author)
Efficiency at maximum power of a discrete feedback ratchet
Jarillo, Javier; Tangarife, Tomás; Cao, Francisco J.
2016-01-01
Efficiency at maximum power is found to be of the same order for a feedback ratchet and for its open-loop counterpart. However, feedback increases the output power up to a factor of five. This increase in output power is due to the increase in energy input and the effective entropy reduction obtained as a consequence of feedback. Optimal efficiency at maximum power is reached for time intervals between feedback actions two orders of magnitude smaller than the characteristic time of diffusion over a ratchet period length. The efficiency is computed consistently taking into account the correlation between the control actions. We consider a feedback control protocol for a discrete feedback flashing ratchet, which works against an external load. We maximize the power output optimizing the parameters of the ratchet, the controller, and the external load. The maximum power output is found to be upper bounded, so the attainable extracted power is limited. After, we compute an upper bound for the efficiency of this isothermal feedback ratchet at maximum power output. We make this computation applying recent developments of the thermodynamics of feedback-controlled systems, which give an equation to compute the entropy reduction due to information. However, this equation requires the computation of the probability of each of the possible sequences of the controller's actions. This computation becomes involved when the sequence of the controller's actions is non-Markovian, as is the case in most feedback ratchets. We here introduce an alternative procedure to set strong bounds to the entropy reduction in order to compute its value. In this procedure the bounds are evaluated in a quasi-Markovian limit, which emerge when there are big differences between the stationary probabilities of the system states. These big differences are an effect of the potential strength, which minimizes the departures from the Markovianicity of the sequence of control actions, allowing also to
Small scale wind energy harvesting with maximum power tracking
Joaquim Azevedo
2015-07-01
Full Text Available It is well-known that energy harvesting from wind can be used to power remote monitoring systems. There are several studies that use wind energy in small-scale systems, mainly with wind turbine vertical axis. However, there are very few studies with actual implementations of small wind turbines. This paper compares the performance of horizontal and vertical axis wind turbines for energy harvesting on wireless sensor network applications. The problem with the use of wind energy is that most of the time the wind speed is very low, especially at urban areas. Therefore, this work includes a study on the wind speed distribution in an urban environment and proposes a controller to maximize the energy transfer to the storage systems. The generated power is evaluated by simulation and experimentally for different load and wind conditions. The results demonstrate the increase in efficiency of wind generators that use maximum power transfer tracking, even at low wind speeds.
Individual Module Maximum Power Point Tracking for a Thermoelectric Generator Systems
Vadstrup, Casper; Chen, Min; Schaltz, Erik
Thermo Electric Generator (TEG) modules are often connected in a series and/or parallel system in order to match the TEG system voltage with the load voltage. However, in order to be able to control the power production of the TEG system a DC/DC converter is inserted between the TEG system...... and the load. The DC/DC converter is under the control of a Maximum Power Point Tracker (MPPT) which insures that the TEG system produces the maximum possible power to the load. However, if the conditions, e.g. temperature, health, etc., of the TEG modules are different each TEG module will not produce its...... maximum power. The result of the system MPPT is therefore the best compromise of all the TEG modules in the system. On the other hand, if each TEG module is controlled individual, each TEG module can be operated in its maximum power point and the TEG system output power will therefore be higher...
LITERATURE REVIEW ON MAXIMUM LOADING OF RADIONUCLIDES ON CRYSTALLINE SILICOTITANATE
Adu-Wusu, K.; Pennebaker, F.
2010-10-13
Plans are underway to use small column ion exchange (SCIX) units installed in high-level waste tanks to remove Cs-137 from highly alkaline salt solutions at Savannah River Site. The ion exchange material slated for the SCIX project is engineered or granular crystalline silicotitanate (CST). Information on the maximum loading of radionuclides on CST is needed by Savannah River Remediation for safety evaluations. A literature review has been conducted that culminated in the estimation of the maximum loading of all but one of the radionuclides of interest (Cs-137, Sr-90, Ba-137m, Pu-238, Pu-239, Pu-240, Pu-241, Am-241, and Cm-244). No data was found for Cm-244.
Miyaguchi, Kazuyoshi; Demura, Shinichi
2008-11-01
This study aimed to examine the relationships between muscle power output using the stretch-shortening cycle (SSC) and eccentric maximum strength under elbow flexion. Eighteen young adult males pulled up a constant light load (2 kg) by ballistic elbow flexion under the following two preliminary conditions: 1) the static relaxed muscle state (SR condition), and 2) using the SSC with countermovement (SSC condition).Muscle power was determined from the product of the pulling velocity and the load mass by a power measurement instrument that adopted the weight-loading method. We assumed the pulling velocity to be the subject's muscle power parameters as a matter of convenience, because we used a constant load. The following two parameters were selected in reference to a previous study: 1) peak velocity (m x s(-1)) (peak power) and 2) 0.1-second velocity during concentric contraction (m x s(-1)) (initial power). Eccentric maximum strength by elbow flexion was measured by a handheld dynamometer.Initial power produced in the SSC condition was significantly larger than that in the SR condition. Eccentric maximum strength showed a significant and high correlation (r = 0.70) with peak power in the SSC condition but not in the SR condition. Eccentric maximum strength showed insignificant correlations with initial power in both conditions. In conclusion, it was suggested that eccentric maximum strength is associated with peak power in the SSC condition, but the contribution of the eccentric maximum strength to the SSC potentiation (initial power) may be low.
Mohsen Taherbaneh; A. H. Rezaie; H. Ghafoorifard; Rahimi, K; M. B. Menhaj
2010-01-01
In applications with low-energy conversion efficiency, maximizing the output power improves the efficiency. The maximum output power of a solar panel depends on the environmental conditions and load profile. In this paper, a method based on simultaneous use of two fuzzy controllers is developed in order to maximize the generated output power of a solar panel in a photovoltaic system: fuzzy-based sun tracking and maximum power point tracking. The sun tracking is performed by changing the solar...
Power Load Management as a Computational Market
Ygge, Fredrik; Akkermans, Hans; Akkermans, J.M.
1997-01-01
Power load management enables energy utilities to reduce peak loads and thereby save money. Due to the large number of different loads, power load management is a complicated optimization problem. We present a new decentralized approach to this problem by modeling direct load management as a
Power Load Management as a Computational Market
Ygge, F.; Akkermans, J.M.
1996-01-01
Power load management enables energy utilities to reduce peak loads and thereby save money. Due to the large number of different loads, power load management is a complicated optimization problem. We present a new decentralized approach to this problem by modeling direct load management as a computa
Power Load Management as a Computational Market
Ygge, Fredrik; Akkermans, Hans
1997-01-01
Power load management enables energy utilities to reduce peak loads and thereby save money. Due to the large number of different loads, power load management is a complicated optimization problem. We present a new decentralized approach to this problem by modeling direct load management as a computa
Maximum Allowable Dynamic Load of Mobile Manipulators with Stability Consideration
Heidary H. R.
2015-09-01
Full Text Available High payload to mass ratio is one of the advantages of mobile robot manipulators. In this paper, a general formula for finding the maximum allowable dynamic load (MADL of wheeled mobile robot is presented. Mobile manipulators operating in field environments will be required to manipulate large loads, and to perform such tasks on uneven terrain, which may cause the system to reach dangerous tip-over instability. Therefore, the method is expanded for finding the MADL of mobile manipulators with stability consideration. Moment-Height Stability (MHS criterion is used as an index for the system stability. Full dynamic model of wheeled mobile base and mounted manipulator is considered with respect to the dynamic of non-holonomic constraint. Then, a method for determination of the maximum allowable loads is described, subject to actuator constraints and by imposing the stability limitation as a new constraint. The actuator torque constraint is applied by using a speed-torque characteristics curve of a typical DC motor. In order to verify the effectiveness of the presented algorithm, several simulation studies considering a two-link planar manipulator, mounted on a mobile base are presented and the results are discussed.
Chen, Jincan; Yan, Zijun; Wu, Liqing
1996-06-01
Considering a thermoelectric generator as a heat engine cycle, the general differential equations of the temperature field inside thermoelectric elements are established by means of nonequilibrium thermodynamics. These equations are used to study the influence of heat leak, Joule's heat, and Thomson heat on the performance of the thermoelectric generator. New expressions are derived for the power output and the efficiency of the thermoelectric generator. The maximum power output is calculated and the optimal matching condition of load is determined. The maximum efficiency is discussed by a representative numerical example. The aim of this research is to provide some novel conclusions and redress some errors existing in a related investigation.
TE(01) High Power Disk Loaded Guide Load
Farkas, Zoltan D
2005-01-01
A method to design a matching section from a smooth guide to a disk loaded guide, using a variation of broadband matching* is described. Using this method, we show how to design high power loads, filters and attenuators. The load consists of a disk loaded coaxial guide, operating in the T01
Global Maximum Power Point Tracking of Photovoltaic Array under Partial Shaded Conditions
G.Shobana, P. Sornadeepika, Dr. R. Ramaprabha
2013-07-01
Full Text Available Efficiency of the PV module can be improved by operating at its peak power point so that the maximum power can be delivered to the load under varying environmental conditions. This paper is mainly focused on the maximum power point tracking of solar photovoltaic array (PV under non uniform insolation conditions. A maximum power point tracker (MPPT is used for extracting the maximum power from the solar PV module and transferring that power to the load. The problem of maximum power point (MPP tracking becomes a problem when the array receives non uniform insolation. Cells under shade absorb a large amount of electric power generated by cells receiving high insolation and convert it into heat which may damage the low illuminated cells. To relieve the stress on shaded cells, bypass diodes are added across the modules. In such a case multiple peaks in voltagepower characteristics are observed. Classical MPPT methods are not effective due to their inability to discriminate between local and global maximum. In this paper, Global MPPT algorithm is proposed to track the global maximum power point of PV array under partial shaded conditions.
A hybrid solar panel maximum power point search method that uses light and temperature sensors
Ostrowski, Mariusz
2016-04-01
Solar cells have low efficiency and non-linear characteristics. To increase the output power solar cells are connected in more complex structures. Solar panels consist of series of connected solar cells with a few bypass diodes, to avoid negative effects of partial shading conditions. Solar panels are connected to special device named the maximum power point tracker. This device adapt output power from solar panels to load requirements and have also build in a special algorithm to track the maximum power point of solar panels. Bypass diodes may cause appearance of local maxima on power-voltage curve when the panel surface is illuminated irregularly. In this case traditional maximum power point tracking algorithms can find only a local maximum power point. In this article the hybrid maximum power point search algorithm is presented. The main goal of the proposed method is a combination of two algorithms: a method that use temperature sensors to track maximum power point in partial shading conditions and a method that use illumination sensor to track maximum power point in equal illumination conditions. In comparison to another methods, the proposed algorithm uses correlation functions to determinate the relationship between values of illumination and temperature sensors and the corresponding values of current and voltage in maximum power point. In partial shading condition the algorithm calculates local maximum power points bases on the value of temperature and the correlation function and after that measures the value of power on each of calculated point choose those with have biggest value, and on its base run the perturb and observe search algorithm. In case of equal illumination algorithm calculate the maximum power point bases on the illumination value and the correlation function and on its base run the perturb and observe algorithm. In addition, the proposed method uses a special coefficient modification of correlation functions algorithm. This sub
14 CFR 25.363 - Side load on engine and auxiliary power unit mounts.
2010-01-01
... § 25.363 Side load on engine and auxiliary power unit mounts. (a) Each engine and auxiliary power unit... the side load on the engine and auxiliary power unit mount, at least equal to the maximum load factor... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Side load on engine and auxiliary...
Thermoelectric Power Generator Design for Maximum Power: It's All About ZT
McCarty, R.
2013-07-01
There is a significant amount of literature that discusses thermoelectric power generator (TEG) design, but much of it overly simplifies the design space and therefore the results have limited use in designing real-life systems. This paper develops a more comprehensive model of the thermal and electrical interactions of a TEG in a system with known hot-side and cold-side thermal resistances and corresponding constant system temperature differential. Two design scenarios are investigated for common TEG system applications. In one method, the power from a TEG is maximized for a given electrical load, simulating a case where the TEG is electrically in series with a known load such as a fan. In the second design scenario, the power from a TEG is maximized for a given electrical load resistance ratio, n (the ratio between the external load resistance and the internal TEG resistance), simulating an application where the TEG is electrically in series with a load-matching converter. An interesting conclusion from this work is that, in the first design scenario, the electrical load resistance ratio, n, that maximizes TEG power occurs at √{1 + ZT} (where ZT is the thermoelectric figure of merit) instead of 1 as reported previously in literature. Equally interesting is that, if you define an analogous thermal resistance ratio, m' (representing the ratio between the TEG thermal resistance at open-circuit conditions and the system thermal resistance), the maximum power in both design scenarios occurs at √{1 + ZT} instead of the commonly cited value of 1. Furthermore, results are presented for real-life designs that incorporate electrical and thermal losses common to realistic TEG systems such as electrical contact resistance and thermal bypass around the TEG due to sealing.
LOAD THAT MAXIMIZES POWER OUTPUT IN COUNTERMOVEMENT JUMP
Pedro Jimenez-Reyes
2016-02-01
Full Text Available ABSTRACT Introduction: One of the main problems faced by strength and conditioning coaches is the issue of how to objectively quantify and monitor the actual training load undertaken by athletes in order to maximize performance. It is well known that performance of explosive sports activities is largely determined by mechanical power. Objective: This study analysed the height at which maximal power output is generated and the corresponding load with which is achieved in a group of male-trained track and field athletes in the test of countermovement jump (CMJ with extra loads (CMJEL. Methods: Fifty national level male athletes in sprinting and jumping performed a CMJ test with increasing loads up to a height of 16 cm. The relative load that maximized the mechanical power output (Pmax was determined using a force platform and lineal encoder synchronization and estimating the power by peak power, average power and flight time in CMJ. Results: The load at which the power output no longer existed was at a height of 19.9 ± 2.35, referring to a 99.1 ± 1% of the maximum power output. The load that maximizes power output in all cases has been the load with which an athlete jump a height of approximately 20 cm. Conclusion: These results highlight the importance of considering the height achieved in CMJ with extra load instead of power because maximum power is always attained with the same height. We advise for the preferential use of the height achieved in CMJEL test, since it seems to be a valid indicative of an individual's actual neuromuscular potential providing a valid information for coaches and trainers when assessing the performance status of our athletes and to quantify and monitor training loads, measuring only the height of the jump in the exercise of CMJEL.
Norhisam Misron
2016-08-01
Full Text Available A new control estimator to maximize the power generated with a maximum power point estimator is introduced. The power mapping characteristics from the double-stator generator are modeled as a mathematical equation which is used to develop the estimator for maximum power tracking to maximize the generated power. The proposed estimator automatically traces the instantaneous maximum power at various load conditions. However, to stabilize the output voltage, a boost converter is used from the inverter side. The developed double-stator generator is tested with the new estimator for the maximizing power generation capability under laboratory conditions. The experimental results confirm that with the new estimator, the average power generation capability is increased by 12% and the peak value is increase by 22%.
MODEL PREDICTIVE CONTROL FOR PHOTOVOLTAIC STATION MAXIMUM POWER POINT TRACKING SYSTEM
I. Elzein
2015-01-01
Full Text Available The purpose of this paper is to present an alternative maximum power point tracking, MPPT, algorithm for a photovoltaic module, PVM, to produce the maximum power, Pmax, using the optimal duty ratio, D, for different types of converters and load matching.We present a state-based approach to the design of the maximum power point tracker for a stand-alone photovoltaic power generation system. The system under consideration consists of a solar array with nonlinear time-varying characteristics, a step-up converter with appropriate filter.The proposed algorithm has the advantages of maximizing the efficiency of the power utilization, can be integrated to other MPPT algorithms without affecting the PVM performance, is excellent for Real-Time applications and is a robust analytical method, different from the traditional MPPT algorithms which are more based on trial and error, or comparisons between present and past states. The procedure to calculate the optimal duty ratio for a buck, boost and buck-boost converters, to transfer the maximum power from a PVM to a load, is presented in the paper. Additionally, the existence and uniqueness of optimal internal impedance, to transfer the maximum power from a photovoltaic module using load matching, is proved.
Effects of loading on maximum vertical jumps: Selective effects of weight and inertia.
Leontijevic, Bojan; Pazin, Nemanja; Bozic, Predrag R; Kukolj, Milos; Ugarkovic, Dusan; Jaric, Slobodan
2012-04-01
A novel loading method was applied to explore selective effects of externally added weight (W), weight and inertia (W+I), and inertia (I) on maximum counter-movement jumps (CMJ) performed with arm swing. Externally applied extended rubber bands and/or loaded vest added W, W+I, and I corresponding to 10-40% of subjects' body mass. As expected, an increase in magnitude of all types of load was associated with an increase in ground reaction forces (GRF), as well as with a decrease in both the jumping performance and power output. However, of more importance could be that discernible differences among the effects of W, W+I, and I were recorded despite a relatively narrow loading range. In particular, an increase in W was associated with the minimal changes in movement kinematic pattern and smallest reduction of jumping performance, while also allowing for the highest power output. Conversely, W+I was associated with the highest ground reaction forces. Finally, the lowest maxima of GRF and power were associated with I. Although further research is apparently needed, the obtained finding could be of potential importance not only for understanding fundamental properties of the neuromuscular system, but also for optimization of loading in standard athletic training and rehabilitation procedures.
Investigation of Maximum Blade Loading Capability of Lift-Offset Rotors
Yeo, Hyeonsoo; Johnson, Wayne
2013-01-01
Maximum blade loading capability of a coaxial, lift-offset rotor is investigated using a rotorcraft configuration designed in the context of short-haul, medium-size civil and military missions. The aircraft was sized for a 6600-lb payload and a range of 300 nm. The rotor planform and twist were optimized for hover and cruise performance. For the present rotor performance calculations, the collective pitch angle is progressively increased up to and through stall with the shaft angle set to zero. The effects of lift offset on rotor lift, power, controls, and blade airloads and structural loads are examined. The maximum lift capability of the coaxial rotor increases as lift offset increases and extends well beyond the McHugh lift boundary as the lift potential of the advancing blades are fully realized. A parametric study is conducted to examine the differences between the present coaxial rotor and the McHugh rotor in terms of maximum lift capabilities and to identify important design parameters that define the maximum lift capability of the rotor. The effects of lift offset on rotor blade airloads and structural loads are also investigated. Flap bending moment increases substantially as lift offset increases to carry the hub roll moment even at low collective values. The magnitude of flap bending moment is dictated by the lift-offset value (hub roll moment) but is less sensitive to collective and speed.
Efficiency at Maximum Power of Interacting Molecular Machines
Golubeva, Natalia; Imparato, Alberto
2012-01-01
We investigate the efficiency of systems of molecular motors operating at maximum power. We consider two models of kinesin motors on a microtubule: for both the simplified and the detailed model, we find that the many-body exclusion effect enhances the efficiency at maximum power of the many- motor...... system, with respect to the single motor case. Remarkably, we find that this effect occurs in a limited region of the system parameters, compatible with the biologically relevant range....
Parametric optimization of thermoelectric elements footprint for maximum power generation
Rezania, A.; Rosendahl, Lasse; Yin, Hao
2014-01-01
The development studies in thermoelectric generator (TEG) systems are mostly disconnected to parametric optimization of the module components. In this study, optimum footprint ratio of n- and p-type thermoelectric (TE) elements is explored to achieve maximum power generation, maximum cost-perform...
Maximum power point tracking for optimizing energy harvesting process
Akbari, S.; Thang, P. C.; Veselov, D. S.
2016-10-01
There has been a growing interest in using energy harvesting techniques for powering wireless sensor networks. The reason for utilizing this technology can be explained by the sensors limited amount of operation time which results from the finite capacity of batteries and the need for having a stable power supply in some applications. Energy can be harvested from the sun, wind, vibration, heat, etc. It is reasonable to develop multisource energy harvesting platforms for increasing the amount of harvesting energy and to mitigate the issue concerning the intermittent nature of ambient sources. In the context of solar energy harvesting, it is possible to develop algorithms for finding the optimal operation point of solar panels at which maximum power is generated. These algorithms are known as maximum power point tracking techniques. In this article, we review the concept of maximum power point tracking and provide an overview of the research conducted in this area for wireless sensor networks applications.
Short-term load forecasting of power system
Xu, Xiaobin
2017-05-01
In order to ensure the scientific nature of optimization about power system, it is necessary to improve the load forecasting accuracy. Power system load forecasting is based on accurate statistical data and survey data, starting from the history and current situation of electricity consumption, with a scientific method to predict the future development trend of power load and change the law of science. Short-term load forecasting is the basis of power system operation and analysis, which is of great significance to unit combination, economic dispatch and safety check. Therefore, the load forecasting of the power system is explained in detail in this paper. First, we use the data from 2012 to 2014 to establish the partial least squares model to regression analysis the relationship between daily maximum load, daily minimum load, daily average load and each meteorological factor, and select the highest peak by observing the regression coefficient histogram Day maximum temperature, daily minimum temperature and daily average temperature as the meteorological factors to improve the accuracy of load forecasting indicators. Secondly, in the case of uncertain climate impact, we use the time series model to predict the load data for 2015, respectively, the 2009-2014 load data were sorted out, through the previous six years of the data to forecast the data for this time in 2015. The criterion for the accuracy of the prediction is the average of the standard deviations for the prediction results and average load for the previous six years. Finally, considering the climate effect, we use the BP neural network model to predict the data in 2015, and optimize the forecast results on the basis of the time series model.
Mohsen Taherbaneh
2010-01-01
Full Text Available In applications with low-energy conversion efficiency, maximizing the output power improves the efficiency. The maximum output power of a solar panel depends on the environmental conditions and load profile. In this paper, a method based on simultaneous use of two fuzzy controllers is developed in order to maximize the generated output power of a solar panel in a photovoltaic system: fuzzy-based sun tracking and maximum power point tracking. The sun tracking is performed by changing the solar panel orientation in horizontal and vertical directions by two DC motors properly designed. A DC-DC converter is employed to track the solar panel maximum power point. In addition, the proposed system has the capability of the extraction of solar panel I-V curves. Experimental results present that the proposed fuzzy techniques result in increasing of power delivery from the solar panel, causing a reduction in size, weight, and cost of solar panels in photovoltaic systems.
A Maximum Power Tracker for Improved Thermophotovoltaic Power Generation Project
National Aeronautics and Space Administration — Radioisotope Power Systems (RPS) are critical for future flagship exploration missions in space and on planetary surfaces. Small improvements in the RPS performance,...
TE_01 High Power Disk Loaded Guide Load
Farkas, Z.D.; /SLAC
2005-06-01
A method to design a matching section from a smooth guide to a disk-loaded guide, using a variation of broadband matching, [1, 2] is described. Using this method, we show how to design high power loads, attenuators and filters. The load consists of a disk-loaded coaxial guide operating in the TE{sub 01}-mode. We use this mode because it has no electric field terminating on a conductor, has no axial currents, and has no current at the cylinder-disk interface. A high power load design that has -35 dB reflection and a 200 MHz, -20 dB bandwidth, is presented. It is expected that it will carry the 600 MW output peak power of the pulse compression network. We use coaxial geometry and stainless steel material to increase the attenuation per cell.
2010-07-01
... as specified in 40 CFR 1065.610. This is the maximum in-use engine speed used for calculating the NOX... procedures of 40 CFR part 1065, based on the manufacturer's design and production specifications for the..., power density, and maximum in-use engine speed. 1042.140 Section 1042.140 Protection of...
Variable structure control for maximum wind power extraction
Barambones, O.; Gonzalez de Durana, J.M.; Alcorta, P. [Univ. of the Basque Country, Vitoria (Spain)
2009-07-01
The future development of wind power technology will affect the level of impact that wind power will have on the power system. Very large wind farms can pose complex technical challenges while also paving the way for other new technologies that will help with electric grid integration. Increasingly complicated power electronic and computerized control schemes will lead to significant improvements and full controllability of available wind power. Reactive power compensation is an important issue in the control of distribution and transmission systems as it increases feeder system losses, reduces system power factor, and can cause large-amplitude variations in load-side voltage. Moreover, rapid changes in the reactive power consumption of large load centers can cause voltage amplitude oscillations, leading to a change in the electric system real power demand resulting in power oscillation. This paper described a sliding mode vector control for a double fed induction generator (DFIG) drive, used in variable speed wind power generation. The study proposed a new variable structure control which has an integral sliding surface to relax the requirement of the acceleration signal, commonly used in conventional sliding mode speed control techniques. The paper discussed the system modelling, DFIG control scheme, and simulation results. A test of the proposed method based on a two-bladed horizontal axis wind turbine was conducted using the Matlab/Simulink software. In this test, several operating conditions were simulated and the study concluded that satisfactory results were obtained. 14 refs., 5 figs.
Power quality load management for large spacecraft electrical power systems
Lollar, Louis F.
1988-01-01
In December, 1986, a Center Director's Discretionary Fund (CDDF) proposal was granted to study power system control techniques in large space electrical power systems. Presented are the accomplishments in the area of power system control by power quality load management. In addition, information concerning the distortion problems in a 20 kHz ac power system is presented.
Control of Hybrid System Using Multi-Input Inverter and Maximum Power Point Tracking
N.Sivakumar
2013-07-01
Full Text Available The objective of this paper is to control the Wind/PV hybrid system using Multi-input inverter to get constant output power for different operating conditions. The MPPT also used in this system to get the maximum peak power to the load. The perturbation observation (P&O method is used to accomplish the maximum power point tracking algorithm for input sources. The operating principle of the open loop and closed loop circuit of multi-input inverter is discussed.
Size dependence of efficiency at maximum power of heat engine
Izumida, Y.
2013-10-01
We perform a molecular dynamics computer simulation of a heat engine model to study how the engine size difference affects its performance. Upon tactically increasing the size of the model anisotropically, we determine that there exists an optimum size at which the model attains the maximum power for the shortest working period. This optimum size locates between the ballistic heat transport region and the diffusive heat transport one. We also study the size dependence of the efficiency at the maximum power. Interestingly, we find that the efficiency at the maximum power around the optimum size attains a value that has been proposed as a universal upper bound, and it even begins to exceed the bound as the size further increases. We explain this behavior of the efficiency at maximum power by using a linear response theory for the heat engine operating under a finite working period, which naturally extends the low-dissipation Carnot cycle model [M. Esposito, R. Kawai, K. Lindenberg, C. Van den Broeck, Phys. Rev. Lett. 105, 150603 (2010)]. The theory also shows that the efficiency at the maximum power under an extreme condition may reach the Carnot efficiency in principle.© EDP Sciences Società Italiana di Fisica Springer-Verlag 2013.
Hadi Sefidgar
2014-06-01
Full Text Available in this paper, a fuzzy logic control (FLC is proposed for maximum power point tracking (MPPT in wind turbine connection to Permanent Magnet Synchronous Generator (PMSG. The proposed fuzzy logic controller tracks the maximum power point (MPP by measurements the load voltage and current. This controller calculates the load power and sent through the fuzzy logic system. The main goal of this paper is design of the fuzzy logic controller in the model of DC-DC converter (boost converter. This method allows the MPPT controller output (duty cycle adjusts the voltage input to the converter to track the maximum power point of the wind generator.
Beat the Deviations in Estimating Maximum Power of Thermoelectric Modules
Gao, Junling; Chen, Min
2013-01-01
Under a certain temperature difference, the maximum power of a thermoelectric module can be estimated by the open-circuit voltage and the short-circuit current. In practical measurement, there exist two switch modes, either from open to short or from short to open, but the two modes can give...... different estimations on the maximum power. Using TEG-127-2.8-3.5-250 and TEG-127-1.4-1.6-250 as two examples, the difference is about 10%, leading to some deviations with the temperature change. This paper analyzes such differences by means of a nonlinear numerical model of thermoelectricity, and finds out...
Efficiency of autonomous soft nanomachines at maximum power.
Seifert, Udo
2011-01-14
We consider nanosized artificial or biological machines working in steady state enforced by imposing nonequilibrium concentrations of solutes or by applying external forces, torques, or electric fields. For unicyclic and strongly coupled multicyclic machines, efficiency at maximum power is not bounded by the linear response value 1/2. For strong driving, it can even approach the thermodynamic limit 1. Quite generally, such machines fall into three different classes characterized, respectively, as "strong and efficient," "strong and inefficient," and "balanced." For weakly coupled multicyclic machines, efficiency at maximum power has lost any universality even in the linear response regime.
Maximum Power Point Tracking Based on Sliding Mode Control
Nimrod Vázquez
2015-01-01
Full Text Available Solar panels, which have become a good choice, are used to generate and supply electricity in commercial and residential applications. This generated power starts with the solar cells, which have a complex relationship between solar irradiation, temperature, and output power. For this reason a tracking of the maximum power point is required. Traditionally, this has been made by considering just current and voltage conditions at the photovoltaic panel; however, temperature also influences the process. In this paper the voltage, current, and temperature in the PV system are considered to be a part of a sliding surface for the proposed maximum power point tracking; this means a sliding mode controller is applied. Obtained results gave a good dynamic response, as a difference from traditional schemes, which are only based on computational algorithms. A traditional algorithm based on MPPT was added in order to assure a low steady state error.
Barboza, Luciano Vitoria [Sul-riograndense Federal Institute for Education, Science and Technology (IFSul), Pelotas, RS (Brazil)], E-mail: luciano@pelotas.ifsul.edu.br
2009-07-01
This paper presents an overview about the maximum load ability problem and aims to study the main factors that limit this load ability. Specifically this study focuses its attention on determining which electric system buses influence directly on the power demand supply. The proposed approach uses the conventional maximum load ability method modelled by an optimization problem. The solution of this model is performed using the Interior Point methodology. As consequence of this solution method, the Lagrange multipliers are used as parameters that identify the probable 'bottlenecks' in the electric power system. The study also shows the relationship between the Lagrange multipliers and the cost function in the Interior Point optimization interpreted like sensitivity parameters. In order to illustrate the proposed methodology, the approach was applied to an IEEE test system and to assess its performance, a real equivalent electric system from the South- Southeast region of Brazil was simulated. (author)
Quantum-dot Carnot engine at maximum power.
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; Van den Broeck, Christian
2010-04-01
We evaluate the efficiency at maximum power of a quantum-dot Carnot heat engine. The universal values of the coefficients at the linear and quadratic order in the temperature gradient are reproduced. Curzon-Ahlborn efficiency is recovered in the limit of weak dissipation.
Recent Developments in Maximum Power Point Tracking Technologies for Photovoltaic Systems
Nevzat Onat
2010-01-01
Full Text Available In photovoltaic (PV system applications, it is very important to design a system for operating of the solar cells (SCs under best conditions and highest efficiency. Maximum power point (MPP varies depending on the angle of sunlight on the surface of the panel and cell temperature. Hence, the operating point of the load is not always MPP of PV system. Therefore, in order to supply reliable energy to the load, PV systems are designed to include more than the required number of modules. The solution to this problem is that switching power converters are used, that is called maximum power point tracker (MPPT. In this study, the various aspects of these algorithms have been analyzed in detail. Classifications, definitions, and basic equations of the most widely used MPPT technologies are given. Moreover, a comparison was made in the conclusion.
Maximum Power Point Tracking Method For PV Array Under Partially Shaded Condition
Belqasem Aljafari
2016-08-01
Full Text Available Solar radiation that hits the photovoltaic modules has a variable character depending on the position, the direction of the solar field, the season, and the hour of the day. During the trajectory of a day, a shadow may be decanted on the cell, which may be contemplated, as in the case of a building near the solar field, or unforeseeable as those created by clouds. The breakthrough of PV systems as distributed power generation systems has increased drastically in the last few years. Because of this Maximum Power Point Tracking (MPPT is becoming more and more substantial as the amount of energy generated by PV systems is increasing. A MPPT technique must be used to track the maximum power point since the MPP depends on solar irradiation and cell temperature. In general, when the impedances of the load and source are matched, the maximum power is transferred to the load from the source only. The generated energy from PV systems must be maximized, as the efficiency of solar panels is low. For that reason to get the maximum power, a PV system is repeatedly equipped with an MPP tracker. Several MPP pursuit techniques have been proposed and implemented in recent years
Maximum-power quantum-mechanical Carnot engine.
Abe, Sumiyoshi
2011-04-01
In their work [J. Phys. A 33, 4427 (2000)], Bender, Brody, and Meister have shown by employing a two-state model of a particle confined in the one-dimensional infinite potential well that it is possible to construct a quantum-mechanical analog of the Carnot engine through changes of both the width of the well and the quantum state in a specific manner. Here, a discussion is developed about realizing the maximum power of such an engine, where the width of the well moves at low but finite speed. The efficiency of the engine at the maximum power output is found to be universal independently of any of the parameters contained in the model.
Novel TPPO Based Maximum Power Point Method for Photovoltaic System
ABBASI, M. A.
2017-08-01
Full Text Available Photovoltaic (PV system has a great potential and it is installed more when compared with other renewable energy sources nowadays. However, the PV system cannot perform optimally due to its solid reliance on climate conditions. Due to this dependency, PV system does not operate at its maximum power point (MPP. Many MPP tracking methods have been proposed for this purpose. One of these is the Perturb and Observe Method (P&O which is the most famous due to its simplicity, less cost and fast track. But it deviates from MPP in continuously changing weather conditions, especially in rapidly changing irradiance conditions. A new Maximum Power Point Tracking (MPPT method, Tetra Point Perturb and Observe (TPPO, has been proposed to improve PV system performance in changing irradiance conditions and the effects on characteristic curves of PV array module due to varying irradiance are delineated. The Proposed MPPT method has shown better results in increasing the efficiency of a PV system.
Radio Frequency Power Load and Associated Method
Srinivasan, V. Karthik (Inventor); Freestone, Todd M. (Inventor); Sims, William Herbert, III (Inventor)
2014-01-01
A radio frequency power load and associated method. A radio frequency power load apparatus may include a container with an ionized fluid therein. The apparatus may include one conductor immersed in a fluid and another conductor electrically connected to the container. A radio frequency transmission system may include a radio frequency transmitter, a radio frequency amplifier connected to the transmitter and a radio frequency power load apparatus connected to the amplifier. The apparatus may include a fluid having an ion source therein, one conductor immersed in a fluid, and another conductor electrically connected to the container. A method of dissipating power generated by a radio frequency transmission system may include constructing a waveguide with ionized fluid in a container and connecting the waveguide to an amplifier of the transmission system.
A Digital Coreless Maximum Power Point Tracking Circuit for Thermoelectric Generators
Kim, Shiho; Cho, Sungkyu; Kim, Namjae; Baatar, Nyambayar; Kwon, Jangwoo
2011-05-01
This paper describes a maximum power point tracking (MPPT) circuit for thermoelectric generators (TEG) without a digital controller unit. The proposed method uses an analog tracking circuit that samples the half point of the open-circuit voltage without a digital signal processor (DSP) or microcontroller unit for calculating the peak power point using iterative methods. The simulation results revealed that the MPPT circuit, which employs a boost-cascaded-with-buck converter, handled rapid variation of temperature and abrupt changes of load current; this method enables stable operation with high power transfer efficiency. The proposed MPPT technique is a useful analog MPPT solution for thermoelectric generators.
2014-09-01
photovoltaic ROM read only memory SLR series-loaded resonant VHDL VHSIC hardware description language VHSIC very high speed integrated circuit ZCS zero...high level simulation compiler that produces VHSIC hardware description language ( VHDL ) code for the model built in Simulink. With the VHDL code, the
High power evaluation of X-band high power loads
Matsumoto, Shuji; Syratchev, Igor; Riddone, Germana; Wuensch, Walter
2010-01-01
Several types of X-band high power loads developed for several tens of MW range were designed, fabricated and used for high power tests at X-band facility of KEK. Some of them have been used for many years and few units showed possible deterioration of RF performance. Recently revised-design loads were made by CERN and the high power evaluation was performed at KEK. In this paper, the main requirements are recalled, together with the design features. The high power test results are analysed and presented
Realworld maximum power point tracking simulation of PV system based on Fuzzy Logic control
Othman, Ahmed M.; El-arini, Mahdi M. M.; Ghitas, Ahmed; Fathy, Ahmed
2012-12-01
In the recent years, the solar energy becomes one of the most important alternative sources of electric energy, so it is important to improve the efficiency and reliability of the photovoltaic (PV) systems. Maximum power point tracking (MPPT) plays an important role in photovoltaic power systems because it maximize the power output from a PV system for a given set of conditions, and therefore maximize their array efficiency. This paper presents a maximum power point tracker (MPPT) using Fuzzy Logic theory for a PV system. The work is focused on the well known Perturb and Observe (P&O) algorithm and is compared to a designed fuzzy logic controller (FLC). The simulation work dealing with MPPT controller; a DC/DC Ćuk converter feeding a load is achieved. The results showed that the proposed Fuzzy Logic MPPT in the PV system is valid.
Realworld maximum power point tracking simulation of PV system based on Fuzzy Logic control
Ahmed M. Othman
2012-12-01
Full Text Available In the recent years, the solar energy becomes one of the most important alternative sources of electric energy, so it is important to improve the efficiency and reliability of the photovoltaic (PV systems. Maximum power point tracking (MPPT plays an important role in photovoltaic power systems because it maximize the power output from a PV system for a given set of conditions, and therefore maximize their array efficiency. This paper presents a maximum power point tracker (MPPT using Fuzzy Logic theory for a PV system. The work is focused on the well known Perturb and Observe (P&O algorithm and is compared to a designed fuzzy logic controller (FLC. The simulation work dealing with MPPT controller; a DC/DC Ćuk converter feeding a load is achieved. The results showed that the proposed Fuzzy Logic MPPT in the PV system is valid.
Maximum power point tracking of partially shaded solar photovoltaic arrays
Roy Chowdhury, Shubhajit; Saha, Hiranmay [IC Design and Fabrication Centre, Department of Electronics and Telecommunication Engineering, Jadavpur University (India)
2010-09-15
The paper presents the simulation and hardware implementation of maximum power point (MPP) tracking of a partially shaded solar photovoltaic (PV) array using a variant of Particle Swarm Optimization known as Adaptive Perceptive Particle Swarm Optimization (APPSO). Under partially shaded conditions, the photovoltaic (PV) array characteristics get more complex with multiple maxima in the power-voltage characteristic. The paper presents an algorithmic technique to accurately track the maximum power point (MPP) of a PV array using an APPSO. The APPSO algorithm has also been validated in the current work. The proposed technique uses only one pair of sensors to control multiple PV arrays. This result in lower cost and higher accuracy of 97.7% compared to earlier obtained accuracy of 96.41% using Particle Swarm Optimization. The proposed tracking technique has been mapped onto a MSP430FG4618 microcontroller for tracking and control purposes. The whole system based on the proposed has been realized on a standard two stage power electronic system configuration. (author)
Designing divertor targets for uniform power load
Dekeyser, W.; Reiter, D.; Baelmans, M.
2015-08-01
Divertor design for next step fusion reactors heavily relies on 2D edge plasma modeling with codes as e.g. B2-EIRENE. While these codes are typically used in a design-by-analysis approach, in previous work we have shown that divertor design can alternatively be posed as a mathematical optimization problem, and solved very efficiently using adjoint methods adapted from computational aerodynamics. This approach has been applied successfully to divertor target shape design for more uniform power load. In this paper, the concept is further extended to include all contributions to the target power load, with particular focus on radiation. In a simplified test problem, we show the potential benefits of fully including the radiation load in the design cycle as compared to only assessing this load in a post-processing step.
2011-01-01
Single-stage grid-connected Photovoltaic (PV) systems have advantages such as simple topology, high efficiency, etc. However, since all the control objectives such as the maximum power point tracking (with the utility voltage, and harmonics reduction for output current need to be considered simultaneously, the complexity of the control scheme is much increased. In this paper a new type of grid connected photovoltaic (PV) system with Maximum Power Point Tracking (MPPT) and reactive power simul...
Modular load flow for restructured power systems
Hariharan, M V; Gupta, Pragati P
2016-01-01
In the subject of power systems, authors felt that a re-look is necessary at some conventional methods of analysis. In this book, the authors have subjected the time-honoured load flow to a close scrutiny. Authors have discovered and discussed a new load flow procedure – Modular Load Flow. Modular Load Flow explores use of power – a scalar – as source for electrical circuits which are conventionally analysed by means of phasors – the ac voltages or currents. The method embeds Kirchhoff’s circuit laws as topological property into its scalar equations and results in a unique wonderland where phase angles do not exist! Generators are shown to have their own worlds which can be superimposed to obtain the state of the composite power system. The treatment is useful in restructured power systems where stakeholders and the system operators may desire to know individual generator contributions in line flows and line losses for commercial reasons. Solution in Modular Load Flow consists of explicit expression...
Maximum Likelihood Estimation of Time-Varying Loadings in High-Dimensional Factor Models
Mikkelsen, Jakob Guldbæk; Hillebrand, Eric; Urga, Giovanni
In this paper, we develop a maximum likelihood estimator of time-varying loadings in high-dimensional factor models. We specify the loadings to evolve as stationary vector autoregressions (VAR) and show that consistent estimates of the loadings parameters can be obtained by a two-step maximum...... likelihood estimation procedure. In the first step, principal components are extracted from the data to form factor estimates. In the second step, the parameters of the loadings VARs are estimated as a set of univariate regression models with time-varying coefficients. We document the finite...
2014-01-01
The power converter is one of the essential elements for effective use of renewable power sources. This paper focuses on the development of a circuit simulation model for maximum power point tracking (MPPT) evaluation of solar power that involves using different buck-boost power converter topologies; including SEPIC, Zeta, and four-switch type buck-boost DC/DC converters. The circuit simulation model mainly includes three subsystems: a PV model; a buck-boost converter-based MPPT system; and ...
Effective soil hydraulic conductivity predicted with the maximum power principle
Westhoff, Martijn; Erpicum, Sébastien; Archambeau, Pierre; Pirotton, Michel; Zehe, Erwin; Dewals, Benjamin
2016-04-01
Drainage of water in soils happens for a large extent through preferential flowpaths, but these subsurface flowpaths are extremely difficult to observe or parameterize in hydrological models. To potentially overcome this problem, thermodynamic optimality principles have been suggested to predict effective parametrization of these (sub-grid) structures, such as the maximum entropy production principle or the equivalent maximum power principle. These principles have been successfully applied to predict heat transfer from the Equator to the Poles, or turbulent heat fluxes between the surface and the atmosphere. In these examples, the effective flux adapts itself to its boundary condition by adapting its effective conductance through the creation of e.g. convection cells. However, flow through porous media, such as soils, can only quickly adapt its effective flow conductance by creation of preferential flowpaths, but it is unknown if this is guided by the aim to create maximum power. Here we show experimentally that this is indeed the case: In the lab, we created a hydrological analogue to the atmospheric model dealing with heat transport between Equator and poles. The experimental setup consists of two freely draining reservoirs connected with each other by a confined aquifer. By adding water to only one reservoir, a potential difference will build up until a steady state is reached. From the steady state potential difference and the observed flow through the aquifer, and effective hydraulic conductance can be determined. This observed conductance does correspond to the one maximizing power of the flux through the confined aquifer. Although this experiment is done in an idealized setting, it opens doors for better parameterizing hydrological models. Furthermore, it shows that hydraulic properties of soils are not static, but they change with changing boundary conditions. A potential limitation to the principle is that it only applies to steady state conditions
Two-Stage Chaos Optimization Search Application in Maximum Power Point Tracking of PV Array
Lihua Wang
2014-01-01
Full Text Available In order to deliver the maximum available power to the load under the condition of varying solar irradiation and environment temperature, maximum power point tracking (MPPT technologies have been used widely in PV systems. Among all the MPPT schemes, the chaos method is one of the hot topics in recent years. In this paper, a novel two-stage chaos optimization method is presented which can make search faster and more effective. In the process of proposed chaos search, the improved logistic mapping with the better ergodic is used as the first carrier process. After finding the current optimal solution in a certain guarantee, the power function carrier as the secondary carrier process is used to reduce the search space of optimized variables and eventually find the maximum power point. Comparing with the traditional chaos search method, the proposed method can track the change quickly and accurately and also has better optimization results. The proposed method provides a new efficient way to track the maximum power point of PV array.
Efficiency at maximum power of a chemical engine.
Hooyberghs, Hans; Cleuren, Bart; Salazar, Alberto; Indekeu, Joseph O; Van den Broeck, Christian
2013-10-01
A cyclically operating chemical engine is considered that converts chemical energy into mechanical work. The working fluid is a gas of finite-sized spherical particles interacting through elastic hard collisions. For a generic transport law for particle uptake and release, the efficiency at maximum power η(mp) [corrected] takes the form 1/2+cΔμ+O(Δμ(2)), with 1∕2 a universal constant and Δμ the chemical potential difference between the particle reservoirs. The linear coefficient c is zero for engines featuring a so-called left/right symmetry or particle fluxes that are antisymmetric in the applied chemical potential difference. Remarkably, the leading constant in η(mp) [corrected] is non-universal with respect to an exceptional modification of the transport law. For a nonlinear transport model, we obtain η(mp) = 1/(θ + 1) [corrected], with θ > 0 the power of Δμ in the transport equation.
Efficiency at maximum power of a chemical engine
Hooyberghs, Hans; Salazar, Alberto; Indekeu, Joseph O; Broeck, Christian Van den
2013-01-01
A cyclically operating chemical engine is considered that converts chemical energy into mechanical work. The working fluid is a gas of finite-sized spherical particles interacting through elastic hard collisions. For a generic transport law for particle uptake and release, the efficiency at maximum power $\\eta$ takes the form 1/2+c\\Delta \\mu + O(\\Delta \\mu^2), with 1/2 a universal constant and $\\Delta \\mu$ the chemical potential difference between the particle reservoirs. The linear coefficient c is zero for engines featuring a so-called left/right symmetry or particle fluxes that are antisymmetric in the applied chemical potential difference. Remarkably, the leading constant in $\\eta$ is non-universal with respect to an exceptional modification of the transport law. For a nonlinear transport model we obtain \\eta = 1/(\\theta +1), with \\theta >0 the power of $\\Delta \\mu$ in the transport equation
Maximum-power-point tracking control of solar heating system
Huang, Bin-Juine
2012-11-01
The present study developed a maximum-power point tracking control (MPPT) technology for solar heating system to minimize the pumping power consumption at an optimal heat collection. The net solar energy gain Q net (=Q s-W p/η e) was experimentally found to be the cost function for MPPT with maximum point. The feedback tracking control system was developed to track the optimal Q net (denoted Q max). A tracking filter which was derived from the thermal analytical model of the solar heating system was used to determine the instantaneous tracking target Q max(t). The system transfer-function model of solar heating system was also derived experimentally using a step response test and used in the design of tracking feedback control system. The PI controller was designed for a tracking target Q max(t) with a quadratic time function. The MPPT control system was implemented using a microprocessor-based controller and the test results show good tracking performance with small tracking errors. It is seen that the average mass flow rate for the specific test periods in five different days is between 18.1 and 22.9kg/min with average pumping power between 77 and 140W, which is greatly reduced as compared to the standard flow rate at 31kg/min and pumping power 450W which is based on the flow rate 0.02kg/sm 2 defined in the ANSI/ASHRAE 93-1986 Standard and the total collector area 25.9m 2. The average net solar heat collected Q net is between 8.62 and 14.1kW depending on weather condition. The MPPT control of solar heating system has been verified to be able to minimize the pumping energy consumption with optimal solar heat collection. © 2012 Elsevier Ltd.
Integrating Autonomous Load Controllers in Power Systems
Douglass, Philip James
violations of voltage constraints. This voltage-sensitive controller can also operate alone, without the frequency-sensitive controller, to provide voltage regulation service and increase load diversity in any distribution network where lower voltage level corresponds to higher load.The frequency......-sensitive and voltage-sensitive autonomous load are viable alternatives to conventional frequency and voltage control devices. When used in combination, they complement each other. In systems where the operator has centrally dispatchable resources to regulate frequency, these resources can be used to dispatch otherwise...... autonomous frequency-sensitive loads. Moreover, where centrally dispatchable frequency regulation resources can rapidly change operating points, such as in a micro-grid, the energy sources can be used as transmitters for a ultra-low-bandwidth uni-directional power line communication system....
Maximum power analysis of photovoltaic module in Ramadi city
Shahatha Salim, Majid; Mohammed Najim, Jassim [College of Science, University of Anbar (Iraq); Mohammed Salih, Salih [Renewable Energy Research Center, University of Anbar (Iraq)
2013-07-01
Performance of photovoltaic (PV) module is greatly dependent on the solar irradiance, operating temperature, and shading. Solar irradiance can have a significant impact on power output of PV module and energy yield. In this paper, a maximum PV power which can be obtain in Ramadi city (100km west of Baghdad) is practically analyzed. The analysis is based on real irradiance values obtained as the first time by using Soly2 sun tracker device. Proper and adequate information on solar radiation and its components at a given location is very essential in the design of solar energy systems. The solar irradiance data in Ramadi city were analyzed based on the first three months of 2013. The solar irradiance data are measured on earth's surface in the campus area of Anbar University. Actual average data readings were taken from the data logger of sun tracker system, which sets to save the average readings for each two minutes and based on reading in each one second. The data are analyzed from January to the end of March-2013. Maximum daily readings and monthly average readings of solar irradiance have been analyzed to optimize the output of photovoltaic solar modules. The results show that the system sizing of PV can be reduced by 12.5% if a tracking system is used instead of fixed orientation of PV modules.
Maximum power analysis of photovoltaic module in Ramadi city
Majid Shahatha Salim, Jassim Mohammed Najim, Salih Mohammed Salih
2013-01-01
Full Text Available Performance of photovoltaic (PV module is greatly dependent on the solar irradiance, operating temperature, and shading. Solar irradiance can have a significant impact on power output of PV module and energy yield. In this paper, a maximum PV power which can be obtain in Ramadi city (100km west of Baghdad is practically analyzed. The analysis is based on real irradiance values obtained as the first time by using Soly2 sun tracker device. Proper and adequate information on solar radiation and its components at a given location is very essential in the design of solar energy systems. The solar irradiance data in Ramadi city were analyzed based on the first three months of 2013. The solar irradiance data are measured on earth's surface in the campus area of Anbar University. Actual average data readings were taken from the data logger of sun tracker system, which sets to save the average readings for each two minutes and based on reading in each one second. The data are analyzed from January to the end of March-2013. Maximum daily readings and monthly average readings of solar irradiance have been analyzed to optimize the output of photovoltaic solar modules. The results show that the system sizing of PV can be reduced by 12.5% if a tracking system is used instead of fixed orientation of PV modules.
Fang, W.; Quan, S. H.; Xie, C. J.; Tang, X. F.; Wang, L. L.; Huang, L.
2016-03-01
In this study, a direct-current/direct-current (DC/DC) converter with maximum power point tracking (MPPT) is developed to down-convert the high voltage DC output from a thermoelectric generator to the lower voltage required to charge batteries. To improve the tracking accuracy and speed of the converter, a novel MPPT control scheme characterized by an aggregated dichotomy and gradient (ADG) method is proposed. In the first stage, the dichotomy algorithm is used as a fast search method to find the approximate region of the maximum power point. The gradient method is then applied for rapid and accurate tracking of the maximum power point. To validate the proposed MPPT method, a test bench composed of an automobile exhaust thermoelectric generator was constructed for harvesting the automotive exhaust heat energy. Steady-state and transient tracking experiments under five different load conditions were carried out using a DC/DC converter with the proposed ADG and with three traditional methods. The experimental results show that the ADG method can track the maximum power within 140 ms with a 1.1% error rate when the engine operates at 3300 rpm@71 NM, which is superior to the performance of the single dichotomy method, the single gradient method and the perturbation and observation method from the viewpoint of improved tracking accuracy and speed.
Investigation of Maximum Power Point Tracking for Thermoelectric Generators
Phillip, Navneesh; Maganga, Othman; Burnham, Keith J.; Ellis, Mark A.; Robinson, Simon; Dunn, Julian; Rouaud, Cedric
2013-07-01
In this paper, a thermoelectric generator (TEG) model is developed as a tool for investigating optimized maximum power point tracking (MPPT) algorithms for TEG systems within automotive exhaust heat energy recovery applications. The model comprises three main subsystems that make up the TEG system: the heat exchanger, thermoelectric material, and power conditioning unit (PCU). In this study, two MPPT algorithms known as the perturb and observe (P&O) algorithm and extremum seeking control (ESC) are investigated. A synchronous buck-boost converter is implemented as the preferred DC-DC converter topology, and together with the MPPT algorithm completes the PCU architecture. The process of developing the subsystems is discussed, and the advantage of using the MPPT controller is demonstrated. The simulation results demonstrate that the ESC algorithm implemented in combination with a synchronous buck-boost converter achieves favorable power outputs for TEG systems. The appropriateness is by virtue of greater responsiveness to changes in the system's thermal conditions and hence the electrical potential difference generated in comparison with the P&O algorithm. The MATLAB/Simulink environment is used for simulation of the TEG system and comparison of the investigated control strategies.
Abhijit Sinha
2014-01-01
Full Text Available A comparative analysis on thermodynamic efficiency based on maximum power & power density conditions have been performed for a solar-driven Carnot heat engine with internal irreversibility. In this analysis, the heat transfer from the hot reservoir is to be in the radiation mode and the heat transfer to the cold reservoir is to be in the convection mode. The thermodynamic efficiency function, power & power density functions have been derived and maximization of the power functions have been performed for various design parameters. From the optimum conditions, the thermal efficiencies at maximum power and power densities have been obtained. The effects of internal irreversibility, extreme temperature ratios & specific engine size in area ratio between the hot & cold reservoirs as various design parameters on thermodynamic efficiencies have been investigated for both the conditions. The efficiencies have been compared with Curzon-Ahlborn & Carnot efficiencies respectively.The analysis showed that the efficiency at maximum power output is greater than the efficiency at maximum power density. And the efficiencies can be greater than the Curzon- Ahlborn`s efficiency only for low values of design parameters.
Maximum efficiency of low-dissipation heat engines at arbitrary power
Holubec, Viktor; Ryabov, Artem
2016-07-01
We investigate maximum efficiency at a given power for low-dissipation heat engines. Close to maximum power, the maximum gain in efficiency scales as a square root of relative loss in power and this scaling is universal for a broad class of systems. For low-dissipation engines, we calculate the maximum gain in efficiency for an arbitrary fixed power. We show that engines working close to maximum power can operate at considerably larger efficiency compared to the efficiency at maximum power. Furthermore, we introduce universal bounds on maximum efficiency at a given power for low-dissipation heat engines. These bounds represent direct generalization of the bounds on efficiency at maximum power obtained by Esposito et al (2010 Phys. Rev. Lett. 105 150603). We derive the bounds analytically in the regime close to maximum power and for small power values. For the intermediate regime we present strong numerical evidence for the validity of the bounds.
Efficiency at Maximum Power of Low-Dissipation Carnot Engines
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; van den Broeck, Christian
2010-10-01
We study the efficiency at maximum power, η*, of engines performing finite-time Carnot cycles between a hot and a cold reservoir at temperatures Th and Tc, respectively. For engines reaching Carnot efficiency ηC=1-Tc/Th in the reversible limit (long cycle time, zero dissipation), we find in the limit of low dissipation that η* is bounded from above by ηC/(2-ηC) and from below by ηC/2. These bounds are reached when the ratio of the dissipation during the cold and hot isothermal phases tend, respectively, to zero or infinity. For symmetric dissipation (ratio one) the Curzon-Ahlborn efficiency ηCA=1-Tc/Th is recovered.
Hardware Implementation of Maximum Power Point Tracking for Thermoelectric Generators
Maganga, Othman; Phillip, Navneesh; Burnham, Keith J.; Montecucco, Andrea; Siviter, Jonathan; Knox, Andrew; Simpson, Kevin
2014-06-01
This work describes the practical implementation of two maximum power point tracking (MPPT) algorithms, namely those of perturb and observe, and extremum seeking control. The proprietary dSPACE system is used to perform hardware in the loop (HIL) simulation whereby the two control algorithms are implemented using the MATLAB/Simulink (Mathworks, Natick, MA) software environment in order to control a synchronous buck-boost converter connected to two commercial thermoelectric modules. The process of performing HIL simulation using dSPACE is discussed, and a comparison between experimental and simulated results is highlighted. The experimental results demonstrate the validity of the two MPPT algorithms, and in conclusion the benefits and limitations of real-time implementation of MPPT controllers using dSPACE are discussed.
Efficiency at maximum power of low-dissipation Carnot engines.
Esposito, Massimiliano; Kawai, Ryoichi; Lindenberg, Katja; Van den Broeck, Christian
2010-10-01
We study the efficiency at maximum power, η*, of engines performing finite-time Carnot cycles between a hot and a cold reservoir at temperatures Th and Tc, respectively. For engines reaching Carnot efficiency ηC=1-Tc/Th in the reversible limit (long cycle time, zero dissipation), we find in the limit of low dissipation that η* is bounded from above by ηC/(2-ηC) and from below by ηC/2. These bounds are reached when the ratio of the dissipation during the cold and hot isothermal phases tend, respectively, to zero or infinity. For symmetric dissipation (ratio one) the Curzon-Ahlborn efficiency ηCA=1-√Tc/Th] is recovered.
A Load Balancing Algorithm Based on Maximum Entropy Methods in Homogeneous Clusters
Long Chen
2014-10-01
Full Text Available In order to solve the problems of ill-balanced task allocation, long response time, low throughput rate and poor performance when the cluster system is assigning tasks, we introduce the concept of entropy in thermodynamics into load balancing algorithms. This paper proposes a new load balancing algorithm for homogeneous clusters based on the Maximum Entropy Method (MEM. By calculating the entropy of the system and using the maximum entropy principle to ensure that each scheduling and migration is performed following the increasing tendency of the entropy, the system can achieve the load balancing status as soon as possible, shorten the task execution time and enable high performance. The result of simulation experiments show that this algorithm is more advanced when it comes to the time and extent of the load balance of the homogeneous cluster system compared with traditional algorithms. It also provides novel thoughts of solutions for the load balancing problem of the homogeneous cluster system.
Fischer, Andreas; Aagaard Madsen, Helge
2014-01-01
The maximum fatigue load reduction potential when using trailing edge flaps on mega-watt wind turbines was explored. For this purpose an ideal feed forward control algorithm using the relative velocity and angle of attack at the blade to control the loads was implemented. The algorithm was applie...... the blade load location was investigated. When the algorithm was applied to measured time series a load reduction of 23% was achieved which is still promissing, but significantly lower than the value achieved in computations....
Robust Controller to Extract the Maximum Power of a Photovoltaic System
OULD CHERCHALI Noureddine
2014-05-01
Full Text Available This paper proposes a technique of intelligent control to track the maximum power point (MPPT of a photovoltaic system . The PV system is non-linear and it is exposed to external perturbations like temperature and solar irradiation. Fuzzy logic control is known for its stability and robustness. FLC is adopted in this work for the improvement and optimization of control performance of a photovoltaic system. Another technique called perturb and observe (P & O is studied and compared with the FLC technique. The PV system is constituted of a photovoltaic panel (PV, a DC-DC converter (Boost and a battery like a load. The simulation results are developed in MATLAB / Simulink software. The results show that the controller based on fuzzy logic is better and faster than the conventional controller perturb and observe (P & O and gives a good maximum power of a photovoltaic generator under different changes of weather conditions.
Meng-Hui Wang
2015-08-01
Full Text Available Sliding mode strategy (SMS for maximum power point tracking (MPPT is used in this study of a human power generation system. This approach ensures maximum power at different rotation speeds to increase efficiency and corrects for the lack of robustness in traditional methods. The intelligent extension theory is used to reduce input saturation and high frequency switching in sliding mode strategy, as well as to increase the efficiency and response speed. The experimental results show that the efficiency of the extension SMS (ESMS is 5% higher than in traditional SMS, and the response is 0.5 s faster.
Park, Hyunbin; Sim, Minseob; Kim, Shiho
2015-06-01
We propose a way of achieving maximum power and power-transfer efficiency from thermoelectric generators by optimized selection of maximum-power-point-tracking (MPPT) circuits composed of a boost-cascaded-with-buck converter. We investigated the effect of switch resistance on the MPPT performance of thermoelectric generators. The on-resistances of the switches affect the decrease in the conversion gain and reduce the maximum output power obtainable. Although the incremental values of the switch resistances are small, the resulting difference in the maximum duty ratio between the input and output powers is significant. For an MPPT controller composed of a boost converter with a practical nonideal switch, we need to monitor the output power instead of the input power to track the maximum power point of the thermoelectric generator. We provide a design strategy for MPPT controllers by considering the compromise in which a decrease in switch resistance causes an increase in the parasitic capacitance of the switch.
Jaw-Kuen Shiau
2014-08-01
Full Text Available The power converter is one of the essential elements for effective use of renewable power sources. This paper focuses on the development of a circuit simulation model for maximum power point tracking (MPPT evaluation of solar power that involves using different buck-boost power converter topologies; including SEPIC, Zeta, and four-switch type buck-boost DC/DC converters. The circuit simulation model mainly includes three subsystems: a PV model; a buck-boost converter-based MPPT system; and a fuzzy logic MPPT controller. Dynamic analyses of the current-fed buck-boost converter systems are conducted and results are presented in the paper. The maximum power point tracking function is achieved through appropriate control of the power switches of the power converter. A fuzzy logic controller is developed to perform the MPPT function for obtaining maximum power from the PV panel. The MATLAB-based Simulink piecewise linear electric circuit simulation tool is used to verify the complete circuit simulation model.
Design of Asymmetrical Relay Resonators for Maximum Efficiency of Wireless Power Transfer
Bo-Hee Choi
2016-01-01
Full Text Available This paper presents a new design method of asymmetrical relay resonators for maximum wireless power transfer. A new design method for relay resonators is demanded because maximum power transfer efficiency (PTE is not obtained at the resonant frequency of unit resonator. The maximum PTE for relay resonators is obtained at the different resonances of unit resonator. The optimum design of asymmetrical relay is conducted by both the optimum placement and the optimum capacitance of resonators. The optimum placement is found by scanning the positions of the relays and optimum capacitance can be found by using genetic algorithm (GA. The PTEs are enhanced when capacitance is optimally designed by GA according to the position of relays, respectively, and then maximum efficiency is obtained at the optimum placement of relays. The capacitance of the second resonator to nth resonator and the load resistance should be determined for maximum efficiency while the capacitance of the first resonator and the source resistance are obtained for the impedance matching. The simulated and measured results are in good agreement.
Maximum Power Point Tracking of DC To DC Boost Converter Using Sliding Mode Control
Anusuyadevi R
2013-07-01
Full Text Available A sliding mode controller is used to estimate the maximum power point as a reference for it to track that point and force the PV system to operate in this point. In sliding mode control, the trajectories of the system are forced to reach a sliding manifold of surface, where it exhibit desirable features, in finite time and to stay on the manifold for all future time. The load is composed of a battery bank. It is obtained by controlling the duty cycle of a DC-DC converter using sliding mode control. This method has the advantage that it will guarantee the maximum output power possible by the array configuration while considering the dynamic parameters solar irradiance and delivering more power to charge the battery. The proposed system with sliding mode control is tested using MATLAB / SIMULINK platform in which a maximum power is tracked under constant and varying solar irradiance and delivered to the battery which increasing the current that is charging the battery and reduces the charging time.
Balsalobre-Fernández, Carlos; Tejero-González, Carlos M; Del Campo-Vecino, Juan; Alonso-Curiel, Dionisio
2013-03-01
The aim of this study was to determine the effects of a power training cycle on maximum strength, maximum power, vertical jump height and acceleration in seven high-level 400-meter hurdlers subjected to a specific training program twice a week for 10 weeks. Each training session consisted of five sets of eight jump-squats with the load at which each athlete produced his maximum power. The repetition maximum in the half squat position (RM), maximum power in the jump-squat (W), a squat jump (SJ), countermovement jump (CSJ), and a 30-meter sprint from a standing position were measured before and after the training program using an accelerometer, an infra-red platform and photo-cells. The results indicated the following statistically significant improvements: a 7.9% increase in RM (Z=-2.03, p=0.021, δc=0.39), a 2.3% improvement in SJ (Z=-1.69, p=0.045, δc=0.29), a 1.43% decrease in the 30-meter sprint (Z=-1.70, p=0.044, δc=0.12), and, where maximum power was produced, a change in the RM percentage from 56 to 62% (Z=-1.75, p=0.039, δc=0.54). As such, it can be concluded that strength training with a maximum power load is an effective means of increasing strength and acceleration in high-level hurdlers.
Effects of loading on maximum vertical jumps: selective effects of weight and inertia
Leontijevic, Bojan; Pazin, Nemanja; Bozic, Predrag R.; Kukolj, Milos; Ugarkovic, Dusan; Jaric, Slobodan
2011-01-01
A novel loading method was applied to explore selective effects of externally added weight (W), weight and inertia (W+I), and inertia (I) on maximum counter-movement jumps (CMJ) performed with arm swing. Externally applied extended rubber bands and/or loaded vest added W, W+I, and I corresponding to 10–40% of subjects' body mass. As expected, an increase in magnitude of all types of load was associated with an increase in ground reaction forces (GRF), as well as with a decrease in both the ju...
The Power Reserves Market Creation For The Participants Maximum Benefit
Anatolij Mahnitko
2008-05-01
Full Text Available It is known, that the main task of the electric power system (EPS control is the power supply providing with the minimum expenses for the electric power production. In this case the requirement to the electric power quality, power supply reliability and the limitationson the energy resources cost must be observed. The power reserve presence into EPS is the necessary condition of the guaranteeing the normal operation from the point of view of the regime parameters values. In the proposed paper the problem of the developing the power reserve, presented to sale by the electric power producers, is examined. It is considered the procedure of the power reserve pricedetermination.
Y. Hoseynpoor
2011-12-01
Full Text Available Single-stage grid-connected Photovoltaic (PV systems have advantages such as simple topology, high efficiency, etc. However, since all the control objectives such as the maximum power point tracking (with the utility voltage, and harmonics reduction for output current need to be considered simultaneously, the complexity of the control scheme is much increased. In this paper a new type of grid connected photovoltaic (PV system with Maximum Power Point Tracking (MPPT and reactive power simultaneous control system is presented. System has two controlling loops to obtain the maximum power from the PV array and also has reactive power control (RPC. In order to decrease the complexity, cost and the number of converters, a singlestage PV system is applied. Using RPC and MPPT controllers, reference current is calculated and the current with low THD (<5% is injected to grid through Adaptive Predictive Current Control (APCC and current Controlled Voltage Source Inverter (CCVSI. The operation of the system is classified in to two day and night modes. In day mode MPPT and RPC control is accomplished and in night mode RPC control is accomplished like STATCOM operation. Reactive power control is continuously performed correctly with appropriate speed in two inductive and capacitive modes in both day and night modes. Thus, System Utilization Factor (SUF increases to 100% which is just 20% for common PV systems. Mathematical modeling of the system and the results of simulations in MATLAB/SIMULINK software are presented to investigate the correctness of the results.
PV Maximum Power-Point Tracking by Using Artificial Neural Network
Farzad Sedaghati; Ali Nahavandi; Mohammad Ali Badamchizadeh; Sehraneh Ghaemi; Mehdi Abedinpour Fallah
2012-01-01
In this paper, using artificial neural network (ANN) for tracking of maximum power point is discussed. Error back propagation method is used in order to train neural network. Neural network has advantages of fast and precisely tracking of maximum power point. In this method neural network is used to specify the reference voltage of maximum power point under different atmospheric conditions. By properly controling of dc-dc boost converter, tracking of maximum power point is feasible. To verify...
Determination of maximum power transfer conditions of bimorph piezoelectric energy harvesters
Ahmad, Mahmoud Al
2012-07-23
In this paper, a method to find the maximum power transfer conditions in bimorph piezoelectric-based harvesters is proposed. Explicitly, we derive a closed form expression that relates the load resistance to the mechanical parameters describing the bimorph based on the electromechanical, single degree of freedom, analogy. Further, by taking into account the intrinsic capacitance of the piezoelectric harvester, a more descriptive expression of the resonant frequency in piezoelectric bimorphs was derived. In interest of impartiality, we apply the proposed philosophy on previously published experimental results and compare it with other reported hypotheses. It was found that the proposed method was able to predict the actual optimum load resistance more accurately than other methods reported in the literature. © 2012 American Institute of Physics.
Maximum Power Point Tracking Algorithms for Grid-Connected Photovoltaic Energy Conversion System
J.Surya Kumari
2013-12-01
Full Text Available As the use of energy is increasing, the requirements for the quality of the supplied electrical energy are more tighten. Energy is the most basic and essential of all resources. As conventional sources of energy are rapidly depleting and the cost of energy is rising, photovoltaic energy becomes a promising alternative source. Photovoltaic (PV generation is becoming increasingly important as a renewable source since it exhibits a great many merits such as cleanness, little maintenance and no noise. The output power of PV arrays is always changing with weather conditions, i.e., solar irradiation and atmospheric temperature. Therefore, a Maximum Power Point Tracking (MPPT control to extract maximum power from the PV arrays at real time becomes indispensable in PV generation system. In recent years, a large number of techniques have been proposed for tracking the maximum power point (MPP. MPPT is used in photovoltaic (PV systems to maximize the photovoltaic array output power, irrespective of the temperature and radiation conditions and of the load electrical characteristics the PV array output power is used to directly control the dc/dc converter, thus reducing the complexity of the system. The resulting system has high-efficiency. This paper presents in details comparison of most popular MPPT algorithms techniques which are Perturb & Observe algorithm(P&O and Improved Perturb & Observe algorithm(IPO. Improved Perturb & Observe algorithm (IPO, is a very promising technique that allows the increase of efficiency and reliability of such systems. Modeling and designing a PV system with Improved Perturb & Observe algorithm (IPO is remarkably more complex than implementing a standard MPPT technique. In this paper, Improved Perturb & Observe algorithm (IPO, system for PV arrays is proposed and analyzed.
Projective Power Entropy and Maximum Tsallis Entropy Distributions
Shinto Eguchi; Shogo Kato; Osamu Komori
2011-01-01
We discuss a one-parameter family of generalized cross entropy between two distributions with the power index, called the projective power entropy. The cross entropy is essentially reduced to the Tsallis entropy if two distributions are taken to be equal. Statistical and probabilistic properties associated with the projective power entropy are extensively investigated including a characterization problem of which conditions uniquely determine the projective power entropy up to the power index...
Sliding-Mode Controller for Maximum Power Point Tracking in Grid-Connected Photovoltaic Systems
Paula Andrea Ortiz Valencia
2015-11-01
Full Text Available The maximum power point tracking (MPPT of photovoltaic systems must be as fast and accurate as possible to increase the power production, which eventually increases the PV system profitability. This paper proposes and mathematically analyses a sliding-mode controller to provide a fast and accurate maximum power point tracking in grid-connected photovoltaic systems using a single control stage. This approach avoids the circular dependency in the design of classical cascade controllers used to optimize the photovoltaic system operation, and at the same time, it reduces the number of controllers and avoids the use of linearized models to provide global stability in all the operation range. Such a compact solution also reduces the system cost and implementation complexity. To ensure the stability of the proposed solution, detailed mathematical analyses are performed to demonstrate the fulfillment of the transversality, reachability and equivalent control conditions. Finally, the performance of the proposed solution is validated using detailed simulations, executed in the power electronics simulator PSIM, accounting for both environmental and load perturbations.
Reliability of the one-repetition-maximum power clean test in adolescent athletes.
Faigenbaum, Avery D; McFarland, James E; Herman, Robert E; Naclerio, Fernando; Ratamess, Nicholas A; Kang, Jie; Myer, Gregory D
2012-02-01
Although the power clean test is routinely used to assess strength and power performance in adult athletes, the reliability of this measure in younger populations has not been examined. Therefore, the purpose of this study was to determine the reliability of the 1-repetition maximum (1RM) power clean in adolescent athletes. Thirty-six male athletes (age 15.9 ± 1.1 years, body mass 79.1 ± 20.3 kg, height 175.1 ±7.4 cm) who had >1 year of training experience in weightlifting exercises performed a 1RM power clean on 2 nonconsecutive days in the afternoon following standardized procedures. All test procedures were supervised by a senior level weightlifting coach and consisted of a systematic progression in test load until the maximum resistance that could be lifted for 1 repetition using proper exercise technique was determined. Data were analyzed using an intraclass correlation coefficient (ICC[2,k]), Pearson correlation coefficient (r), repeated measures analysis of variance, Bland-Altman plot, and typical error analyses. Analysis of the data revealed that the test measures were highly reliable demonstrating a test-retest ICC of 0.98 (95% confidence interval = 0.96-0.99). Testing also demonstrated a strong relationship between 1RM measures in trials 1 and 2 (r = 0.98, p adolescent athletes when standardized testing procedures are followed and qualified instruction is present.
RELIABILITY OF THE ONE REPETITION-MAXIMUM POWER CLEAN TEST IN ADOLESCENT ATHLETES
Faigenbaum, Avery D.; McFarland, James E.; Herman, Robert; Naclerio, Fernando; Ratamess, Nicholas A.; Kang, Jie; Myer, Gregory D.
2013-01-01
Although the power clean test is routinely used to assess strength and power performance in adult athletes, the reliability of this measure in younger populations has not been examined. Therefore, the purpose of this study was to determine the reliability of the one repetition maximum (1 RM) power clean in adolescent athletes. Thirty-six male athletes (age 15.9 ± 1.1 yrs, body mass 79.1 ± 20.3 kg, height 175.1 ±7.4 cm) who had more than 1 year of training experience with weightlifting exercises performed a 1 RM power clean on two nonconsecutive days in the afternoon following standardized procedures. All test procedures were supervised by a senior level weightlifting coach and consisted of a systematic progression in test load until the maximum resistance that could be lifted for one repetition using proper exercise technique was determined. Data were analyzed using an intraclass correlation coefficient (ICC [2,k]), Pearson correlation coefficient (r), repeated measures ANOVA, Bland-Altman plot, and typical error analyses. Analysis of the data revealed that the test measures were highly reliable demonstrating a test-retest ICC of 0.98 (95% CI = 0.96–0.99). Testing also demonstrated a strong relationship between 1 RM measures on trial 1 and trial 2 (r=0.98, padolescent athletes when standardized testing procedures are followed and qualified instruction is present. PMID:22233786
Bounds and phase diagram of efficiency at maximum power for tight-coupling molecular motors.
Tu, Z C
2013-02-01
The efficiency at maximum power (EMP) for tight-coupling molecular motors is investigated within the framework of irreversible thermodynamics. It is found that the EMP depends merely on the constitutive relation between the thermodynamic current and force. The motors are classified into four generic types (linear, superlinear, sublinear, and mixed types) according to the characteristics of the constitutive relation, and then the corresponding ranges of the EMP for these four types of molecular motors are obtained. The exact bounds of the EMP are derived and expressed as the explicit functions of the free energy released by the fuel in each motor step. A phase diagram is constructed which clearly shows how the region where the parameters (the load distribution factor and the free energy released by the fuel in each motor step) are located can determine whether the value of the EMP is larger or smaller than 1/2. This phase diagram reveals that motors using ATP as fuel under physiological conditions can work at maximum power with higher efficiency (> 1/2) for a small load distribution factor (< 0.1).
Low reflectance high power RF load
Ives, R. Lawrence; Mizuhara, Yosuke M.
2016-02-02
A load for traveling microwave energy has an absorptive volume defined by cylindrical body enclosed by a first end cap and a second end cap. The first end cap has an aperture for the passage of an input waveguide with a rotating part that is coupled to a reflective mirror. The inner surfaces of the absorptive volume consist of a resistive material or are coated with a coating which absorbs a fraction of incident RF energy, and the remainder of the RF energy reflects. The angle of the reflector and end caps is selected such that reflected RF energy dissipates an increasing percentage of the remaining RF energy at each reflection, and the reflected RF energy which returns to the rotating mirror is directed to the back surface of the rotating reflector, and is not coupled to the input waveguide. Additionally, the reflector may have a surface which generates a more uniform power distribution function axially and laterally, to increase the power handling capability of the RF load. The input waveguide may be corrugated for HE11 mode input energy.
Power System Aggregate Load Area Modelling by Particle Swarm Optimization
Jian-Lin Wei; Ji-Hong Wang; Q.H.Wu; Nan Lu
2005-01-01
This paper presents a new approach for deriving a power system aggregate load area model (ALAM). In this approach, an equivalent area load model is derived to represent the load characters for a particular area load of a power system network. The Particle Swarm Optimization (PSO) method is employed to identify the unknown parameters of the generalised system, ALAM, based on the system measurement directly using a one-step scheme. Simulation studies are carried out for an IEEE 14-Bus power system and an IEEE 57-Bus power system. Simulation results show that the ALAM can represent the area load characters accurately under different operational conditions and at different power system states.
Power amplification in an isolated muscle–tendon unit is load dependent
Sawicki, Gregory S.; Sheppard, Peter; Roberts, Thomas J.
2015-01-01
ABSTRACT During rapid movements, tendons can act like springs, temporarily storing work done by muscles and then releasing it to power body movements. For some activities, such as frog jumping, energy is released from tendon much more rapidly than it is stored, thus amplifying muscle power output. The period during which energy is loaded into a tendon by muscle work may be aided by a catch mechanism that restricts motion, but theoretical studies indicate that power can be amplified in a muscle–tendon load system even in the absence of a catch. To explore the limits of power amplification with and without a catch, we studied the bullfrog plantaris muscle–tendon during in vitro contractions. A novel servomotor controller allowed us to measure muscle–tendon unit (MTU) mechanical behavior during contractions against a variety of simulated inertial-gravitational loads, ranging from zero to 1× the peak isometric force of the muscle. Power output of the MTU system was load dependent and power amplification occurred only at intermediate loads, reaching ∼1.3× the peak isotonic power output of the muscle. With a simulated anatomical catch mechanism in place, the highest power amplification occurred at the lowest loads, with a maximum amplification of more than 4× peak isotonic muscle power. At higher loads, the benefits of a catch for MTU performance diminished sharply, suggesting that power amplification >2.5× may come at the expense of net mechanical work delivered to the load. PMID:26449973
Model Predictive Load Scheduling Using Solar Power Forecasting
Habib, Abdulelah H.; Kleissl, Jan; de Callafon, Raymond A.
2016-01-01
In this paper a model is developed to solve the on/off scheduling of (non-linear) dynamic electric loads based on predictions of the power delivery of a (standalone) solar power source. Knowledge of variations in the solar power output is used to optimally select the timing and the combinations of a set of given electric loads, where each load has a desired dynamic power profile. The optimization exploits the desired power profiles of the electric loads in terms of dynamic power ramp up/down ...
OPTIMIZING THE SHAPE OF ROTOR BLADES FOR MAXIMUM POWER EXTRACTION IN MARINE CURRENT TURBINES
J.A. Esfahani
2012-12-01
Full Text Available In this paper the shape of rotor blades in Marine Current Turbines (MCTs are investigated. The evaluation of hydrodynamic loads on blades is performed based on the Blade Element Momentum (BEM theory. The shape of blades is optimized according to the main parameters in the configuration and operation of these devices. The optimization is conducted based on the ability of the blades to harness the maximum energy during operating. The main parameters investigated are the tip speed ratio and angle of attack. Furthermore, the influence of these parameters on the maximum energy extraction from fluid flow over a hydrofoil is evaluated. It is shown that the effect of the angle of attack on power extraction is greater than that of the tip speed ratio, while both are found to be significant. Additionally, the proper angle of attack is the angle at which the lift to drag ratio is at its maximum value. However, if a proper angle of attack is chosen, the variations in power coefficient would not be effectively changed with small variations in the tip speed ratio.
Ahteshamul Haque
2016-02-01
Full Text Available The energy crisis concern leads to look for alternate source of energy. Solar energy is considered as most reliable among the all renewable energy sources. Solar PV (Photovoltaic is used to convert solar energy into electric energy. The efficiency of solar PV is very low and its characteristic is nonlinear. To overcome these drawbacks a technique known as maximum power point tracking is used. This algorithm is implemented in the control circuit of DC – DC converter. The objective of this paper is to evaluate the MPPT (Maximum Power Point Tracking with buck DC-DC converter under load varying conditions. The simulation work is done using PSIM simulation software.
Troncoso, E. [School of Industrial Engineering, Universidad Las Palmas de Gran Canaria (Spain); Newborough, M. [ITM Power Research Ltd., Mill House, Royston Road, Wendens Ambo, Saffron Walden CB11 4JX (United Kingdom)
2010-01-15
For an isolated power system the deployment of a large stock of electrolysers is investigated as a means for increasing the penetrations of wind power plant and zero-carbon thermal power plant. Consideration is given to the sizing and utilization of an electrolyser stock for three electrolyser implementation cases and three operational strategies, installed capacity ranges of 20-100% for wind power and 10-35% for zero-carbon thermal power plant (as proportions of the power system's maximum electrical demand) were investigated. Relative to wind-hydrogen alone, hydrogen yields are substantially increased especially on low-wind days. The average load placed on fossil-fuelled power plant is substantially decreased (while achieving a virtually flat load profile) and the carbon intensity of electricity can be reduced to values of <0.1 kg CO{sub 2}/kWh{sub e}. The trade-offs between the carbon intensity of the electricity delivered, the carbon intensity of the hydrogen produced and the daily hydrogen yield are explored. For example (on the variable wind day for Strategy C with respective wind power and zero-carbon thermal power penetrations of 100% and 35%), if the carbon intensity of hydrogen is relaxed from 0 to 3 kg CO{sub 2}/kg H{sub 2}, the hydrogen yield can be increased from 435 tonnes to 1115 tonnes (which is the energy equivalent of 120% of consumer demand for electricity on that day). The findings suggest that the deployment of electrolysers on both the supply and demand-side of the power system can contribute nationally-significant amounts of zero or low-carbon hydrogen without exceeding the power system's current maximum system demand. (author)
Optimum blade loading for a powered rotor in descent
Ramin Modarres; David A. Peters
2016-01-01
The optimum loading for rotors has previously been found for hover, climb and wind turbine conditions;but, up to now, no one has determined the optimum rotor loading in descent. This could be an important design consideration for rotary-wing parachutes and low-speed des-cents. In this paper, the optimal loading for a powered rotor in descent is found from momentum theory based on a variational principle. This loading is compared with the optimal loading for a rotor in hover or climb and with the Betz rotor loading (which is optimum for a lightly-loaded rotor). Wake contraction for each of the various loadings is also presented.
Mroczka Janusz
2014-12-01
Full Text Available Photovoltaic panels have a non-linear current-voltage characteristics to produce the maximum power at only one point called the maximum power point. In the case of the uniform illumination a single solar panel shows only one maximum power, which is also the global maximum power point. In the case an irregularly illuminated photovoltaic panel many local maxima on the power-voltage curve can be observed and only one of them is the global maximum. The proposed algorithm detects whether a solar panel is in the uniform insolation conditions. Then an appropriate strategy of tracking the maximum power point is taken using a decision algorithm. The proposed method is simulated in the environment created by the authors, which allows to stimulate photovoltaic panels in real conditions of lighting, temperature and shading.
Design of wind turbine airfoils based on maximum power coefficient
Chen, Jin; Cheng, Jiangtao; Shen, Wenzhong;
2010-01-01
noise prediction model, the previously developed integrated design technique is further developed. The new code takes into account different airfoil requirements according to their local positions on a blade, such as sensitivity to leading edge roughness, design lift at off-design condition, stall......Based on the blade element momentum (BEM) theory, the power coefficient of a wind turbine can be expressed in function of local tip speed ratio and lift-drag ratio. By taking the power coefficient in a predefined range of angle of attack as the final design objective and combining with an airfoil...
Koutroulis, Eftichios; Blaabjerg, Frede
2012-01-01
output, such that it behaves as a constant input-power load. The proposed method has the advantage that it can be applied in either stand-alone or grid-connected PV systems comprising PV arrays with unknown electrical characteristics and does not require knowledge about the PV modules configuration......The power-voltage characteristic of photovoltaic (PV) arrays operating under partial-shading conditions exhibits multiple local maximum power points (MPPs). In this paper, a new method to track the global MPP is presented, which is based on controlling a dc/dc converter connected at the PV array...
Kimble, Michael C.; White, Ralph E.
1991-01-01
A mathematical model of a hydrogen/oxygen alkaline fuel cell is presented that can be used to predict the polarization behavior under various power loads. The major limitations to achieving high power densities are indicated and methods to increase the maximum attainable power density are suggested. The alkaline fuel cell model describes the phenomena occurring in the solid, liquid, and gaseous phases of the anode, separator, and cathode regions based on porous electrode theory applied to three phases. Fundamental equations of chemical engineering that describe conservation of mass and charge, species transport, and kinetic phenomena are used to develop the model by treating all phases as a homogeneous continuum.
H. Ijadi
2012-09-01
Full Text Available In this paper, a method to track the maximum power of solar panels based on fuzzy logic is presented. The proposed method is based on the relationship between radiation intensity and the voltage of maximum power operating point. With this relationship, at any time by measuring the light intensity, voltage can be calculated at the maximum power point by using fuzzy approximation function. In order to verify the proposed method, simulation results are presented.
Power optimization for maximum channel capacity in MIMO relay system
无
2007-01-01
Introducing multiple-input multiple-output (MIMO) relay channel could offer significant capacity gain.And it is of great importance to develop effective power allocation strategies to achieve power efficiency and improve channel capacity in amplify-and-forward relay system.This article investigates a two-hop MIMO relay system with multiple antennas in relay node (RN) and receiver (RX).Maximizing capacity with antenna selection (MCAS) and maximizing capacity with eigen-decomposition (MCED) schemes are proposed to efficiently allocate power among antennas in RN under first and second hop limited scenarios.The analysis and simulation results show that both MCED and MCAS can improve the channel capacity compared with uniform power allocation (UPA) scheme in most of the studied areas.The MCAS bears comparison with MCED with an acceptable capacity loss, but lowers the complexity by saving channel state information (CSI) feedback to the transmitter (TX).Moreover, when the RN is close to RX, the performance of UPA is also close to the upper bound as the performance of first hop is limited.
GA-BASED MAXIMUM POWER DISSIPATION ESTIMATION OF VLSI SEQUENTIAL CIRCUITS OF ARBITRARY DELAY MODELS
Lu Junming; Lin Zhenghui
2002-01-01
In this paper, the glitching activity and process variations in the maximum power dissipation estimation of CMOS circuits are introduced. Given a circuit and the gate library,a new Genetic Algorithm (GA)-based technique is developed to determine the maximum power dissipation from a statistical point of view. The simulation on ISCAS-89 benchmarks shows that the ratio of the maximum power dissipation with glitching activity over the maximum power under zero-delay model ranges from 1.18 to 4.02. Compared with the traditional Monte Carlo-based technique, the new approach presented in this paper is more effective.
GA—BASED MAXIMUM POWER DISSIPATION ESTIMATION OF VLSI SEQUENTIAL CIRCUITS OF ARBITRARY DELAY MODELS
LuJunming; LinZhenghui
2002-01-01
In this paper,the glitching activity and process variations in the maximum power dissipation estimation of CMOS circulits are introduced.Given a circuit and the gate library,a new Genetic Algorithm (GA)-based technique is developed to determine the maximum power dissipation from a statistical point of view.The simulation on ISCAS-89 benchmarks shows that the ratio of the maximum power dissipation with glitching activity over the maximum power under zero-delay model ranges from 1.18 to 4.02.Compared with the traditional Monte Carlo-based technique,the new approach presented in this paper is more effective.
PV Maximum Power-Point Tracking by Using Artificial Neural Network
Farzad Sedaghati
2012-01-01
Full Text Available In this paper, using artificial neural network (ANN for tracking of maximum power point is discussed. Error back propagation method is used in order to train neural network. Neural network has advantages of fast and precisely tracking of maximum power point. In this method neural network is used to specify the reference voltage of maximum power point under different atmospheric conditions. By properly controling of dc-dc boost converter, tracking of maximum power point is feasible. To verify theory analysis, simulation result is obtained by using MATLAB/SIMULINK.
Maximum Power Output of Quantum Heat Engine with Energy Bath
Liu, Shengnan
2016-01-01
The difference between quantum isoenergetic process and quantum isothermal process comes from the violation of the law of equipartition of energy in the quantum regime. To reveal an important physical meaning of this fact, here we study a special type of quantum heat engine consisting of three processes: isoenergetic, isothermal and adiabatic processes. Therefore, this engine works between the energy and heat baths. Combining two engines of this kind, it is possible to realize the quantum Carnot engine. Furthermore, considering finite velocity of change of the potential shape, here an infinite square well with moving walls, the power output of the engine is discussed. It is found that the efficiency and power output are both closely dependent on the initial and final states of the quantum isothermal process. The performance of the engine cycle is shown to be optimized by control of the occupation probability of the ground state, which is determined by the temperature and the potential width. The relation betw...
Maximum Power Output of Quantum Heat Engine with Energy Bath
Shengnan Liu
2016-05-01
Full Text Available The difference between quantum isoenergetic process and quantum isothermal process comes from the violation of the law of equipartition of energy in the quantum regime. To reveal an important physical meaning of this fact, here we study a special type of quantum heat engine consisting of three processes: isoenergetic, isothermal and adiabatic processes. Therefore, this engine works between the energy and heat baths. Combining two engines of this kind, it is possible to realize the quantum Carnot engine. Furthermore, considering finite velocity of change of the potential shape, here an infinite square well with moving walls, the power output of the engine is discussed. It is found that the efficiency and power output are both closely dependent on the initial and final states of the quantum isothermal process. The performance of the engine cycle is shown to be optimized by control of the occupation probability of the ground state, which is determined by the temperature and the potential width. The relation between the efficiency and power output is also discussed.
Prediction of Maximum Strain in Finocyl Port Case-bonded Solid Propellants under Pressure Loading
Himanshu Shekhar
2006-07-01
Full Text Available Finite element analysis of case-bonded solid propellants in finocyl port configuration hasbeen carried out using finite element method. The parametric studies have also been conductedfor loading conditions, material properties, and geometrical configurations. The results arepresented in the form of a universal power law, which can be utilised for primary assessmentof peak strain in any finocyl port propellant configuration without using finite element software.This eliminates dependence on finite element software for structural integrity analysis of solidpropellants in finocyl port configuration under port pressurisation. The results obtained by finiteelement analysis and power law are in close agreement.
Ruikun Mai
2017-02-01
Full Text Available One of the most promising inductive power transfer applications is the wireless power supply for locomotives which may cancel the need for pantographs. In order to meet the dynamic and high power demands of wireless power supplies for locomotives, a relatively long transmitter track and multiple receivers are usually adopted. However, during the dynamic charging, the mutual inductances between the transmitter and receivers vary and the load of the locomotives also changes randomly, which dramatically affects the system efficiency. A maximum efficiency point tracking control scheme is proposed to improve the system efficiency against the variation of the load and the mutual inductances between the transmitter and receivers while considering the cross coupling between receivers. Firstly, a detailed theoretical analysis on dual receivers is carried out. Then a control scheme with three control loops is proposed to regulate the receiver currents to be the same, to regulate the output voltage and to search for the maximum efficiency point. Finally, a 2 kW prototype is established to validate the performance of the proposed method. The overall system efficiency (DC-DC efficiency reaches 90.6% at rated power and is improved by 5.8% with the proposed method under light load compared with the traditional constant output voltage control method.
Using Maximal Isometric Force to Determine the Optimal Load for Measuring Dynamic Muscle Power
Spiering, Barry A.; Lee, Stuart M. C.; Mulavara, Ajitkumar P.; Bentley, Jason R.; Nash, Roxanne E.; Sinka, Joseph; Bloomberg, Jacob J.
2009-01-01
Maximal power output occurs when subjects perform ballistic exercises using loads of 30-50% of one-repetition maximum (1-RM). However, performing 1-RM testing prior to power measurement requires considerable time, especially when testing involves multiple exercises. Maximal isometric force (MIF), which requires substantially less time to measure than 1-RM, might be an acceptable alternative for determining the optimal load for power testing. PURPOSE: To determine the optimal load based on MIF for maximizing dynamic power output during leg press and bench press exercises. METHODS: Twenty healthy volunteers (12 men and 8 women; mean +/- SD age: 31+/-6 y; body mass: 72 +/- 15 kg) performed isometric leg press and bench press movements, during which MIF was measured using force plates. Subsequently, subjects performed ballistic leg press and bench press exercises using loads corresponding to 20%, 30%, 40%, 50%, and 60% of MIF presented in randomized order. Maximal instantaneous power was calculated during the ballistic exercise tests using force plates and position transducers. Repeated-measures ANOVA and Fisher LSD post hoc tests were used to determine the load(s) that elicited maximal power output. RESULTS: For the leg press power test, six subjects were unable to be tested at 20% and 30% MIF because these loads were less than the lightest possible load (i.e., the weight of the unloaded leg press sled assembly [31.4 kg]). For the bench press power test, five subjects were unable to be tested at 20% MIF because these loads were less than the weight of the unloaded aluminum bar (i.e., 11.4 kg). Therefore, these loads were excluded from analysis. A trend (p = 0.07) for a main effect of load existed for the leg press exercise, indicating that the 40% MIF load tended to elicit greater power output than the 60% MIF load (effect size = 0.38). A significant (p . 0.05) main effect of load existed for the bench press exercise; post hoc analysis indicated that the effect of
Design of a control scheme for a maximum power extraction in low power wind turbine-generator system
Henao Bravo, Elkin Edilberto
This document presents the modeling of a wind turbine-generator system and developing a control scheme for maximum power extraction. The system comprises a low-power variable speed wind rotor coupled to a squirrel cage induction generator through gearbox. The generator delivers electrical energy to a DC load through a PWM three phase rectifier which control variables are duty cycle and the fundamental frequency of the modulated signal. The control scheme maintains constant relationship voltage/frequency in the stator of the generator to operate the machine with constant air gap flow at its nominal value, thereby decreasing electrical losses in the circuit of the stator and rotor. The controller is based on MPPT algorithms for determining the operating point the system and achieve the proper mechanical speed shaft. The performance is evaluated through simulations in MatlabRTM/simulink. and presents this type of control as a good alternative for handling low-power wind turbine-generator systems effectively and efficiently
Investigation on the Maximum Power Point in Solar Panel Characteristics Due to Irradiance Changes
Abdullah, M. A.; Fauziah Toha, Siti; Ahmad, Salmiah
2017-03-01
One of the disadvantages of the photovoltaic module as compared to other renewable resources is the dynamic characteristics of solar irradiance due to inconsistency weather condition and surrounding temperature. Commonly, a photovoltaic power generation systems consist of an embedded control system to maximize the power generation due to the inconsistency in irradiance. In order to improve the simplicity of the power optimization control, this paper present the characteristic of Maximum Power Point with various irradiance levels for Maximum Power Point Tracking (MPPT). The technique requires a set of data from photovoltaic simulation model to be extrapolated as a standard relationship between irradiance and maximum power. The result shows that the relationship between irradiance and maximum power can be represented by a simplified quadratic equation. The first section in your paper
Artificial Neural Network In Maximum Power Point Tracking Algorithm Of Photovoltaic Systems
Modestas Pikutis
2014-05-01
Full Text Available Scientists are looking for ways to improve the efficiency of solar cells all the time. The efficiency of solar cells which are available to the general public is up to 20%. Part of the solar energy is unused and a capacity of solar power plant is significantly reduced – if slow controller or controller which cannot stay at maximum power point of solar modules is used. Various algorithms of maximum power point tracking were created, but mostly algorithms are slow or make mistakes. In the literature more and more oftenartificial neural networks (ANN in maximum power point tracking process are mentioned, in order to improve performance of the controller. Self-learner artificial neural network and IncCond algorithm were used for maximum power point tracking in created solar power plant model. The algorithm for control was created. Solar power plant model is implemented in Matlab/Simulink environment.
Ramachandran, Hema; Pillai, K. P. P.; Bindu, G. R.
2016-08-01
A two-port network model for a wireless power transfer system taking into account the distributed capacitances using PP network topology with top coupling is developed in this work. The operating and maximum power transfer efficiencies are determined analytically in terms of S-parameters. The system performance predicted by the model is verified with an experiment consisting of a high power home light load of 230 V, 100 W and is tested for two forced resonant frequencies namely, 600 kHz and 1.2 MHz. The experimental results are in close agreement with the proposed model.
Testing of Uninterruptible Power Supplies with nonlinear loads
Heydt, Gerald; Briggs, Steve; Holcomb, Franklin; Edgar, Daiva
1994-09-01
Uninterruptible power supplies (UPS's) are used to provide power to sensitive and critical loads when the commercial supply has been interrupted. These loads may be nonlinear, which in the military often includes communications equipment, adjustable speed drives, fluorescent lighting, and mainframe and small computers. Most electrical characteristics of UPS's are not currently subject to codes and standards, and there are no military specifications for UPS's. Existing standards assume that UPS's will be operated with linear loads. Since most UPS systems are operated with nonlinear loads, there is concern that UPSs will suffer degraded performance or failure when operated with these loads. This work developed a test methodology by which UPS systems can be tested and their susceptibility to nonlinear loads quantified. The tests measure load transfer, efficiency, heating, load support, voltage regulation, and isolation. Several commercially available UPS systems are recommended for testing.
Neubauer, Michael [Muons, Inc., Batavia, IL (United States); Dudas, Alan [Muons, Inc., Batavia, IL (United States); Krasnykh, Anatoly [SLAC National Accelerator Lab., Menlo Park, CA (United States)
2016-12-29
Through a combination of experimentation and calculation the components of a novel room temperature dry load were successfully fabricated. These components included lossy ceramic cylinders of various lengths, thicknesses, and percent of silicon carbide (SiC). The cylinders were then assembled into stainless steel compression rings by differential heating of the parts and a special fixture. Post machining of this assembly provided a means for a final weld. The ring assemblies were then measured for S-parameters, individually and in pairs using a low-cost TE10 rectangular to TE01 circular waveguide adapter specially designed to be part of the final load assembly. Matched pairs of rings were measured for assembly into the final load and a sliding short designed and fabricated to assist in determining the desired short location in the final assembly. The plan for the project was for Muons, Inc. to produce prototype loads for long-term testing at SLAC. The STTR funds for SLAC were to upgrade and operate their test station to ensure that the loads would satisfy their requirements. Phase III was to be the sale to SLAC of loads that Muons, Inc. would manufacture. However, an alternate solution that involved a rebuild of the old loads, reduced SLAC budget projections, and a relaxed time for the replacement of all loads meant that in-house labor will be used to do the upgrade without the need for the loads developed in this project. Consequently, the project was terminated before the long term testing was initiated. However, SLAC can use the upgraded test stand to compare the long-term performance of the ones produced in this project with their rebuilt loads when they are available.
Maximum organic loading rate for the single-stage wet anaerobic digestion of food waste.
Nagao, Norio; Tajima, Nobuyuki; Kawai, Minako; Niwa, Chiaki; Kurosawa, Norio; Matsuyama, Tatsushi; Yusoff, Fatimah Md; Toda, Tatsuki
2012-08-01
Anaerobic digestion of food waste was conducted at high OLR from 3.7 to 12.9 kg-VS m(-3) day(-1) for 225 days. Periods without organic loading were arranged between the each loading period. Stable operation at an OLR of 9.2 kg-VS (15.0 kg-COD) m(-3) day(-1) was achieved with a high VS reduction (91.8%) and high methane yield (455 mL g-VS-1). The cell density increased in the periods without organic loading, and reached to 10.9×10(10) cells mL(-1) on day 187, which was around 15 times higher than that of the seed sludge. There was a significant correlation between OLR and saturated TSS in the sludge (y=17.3e(0.1679×), r(2)=0.996, P<0.05). A theoretical maximum OLR of 10.5 kg-VS (17.0 kg-COD) m(-3) day(-1) was obtained for mesophilic single-stage wet anaerobic digestion that is able to maintain a stable operation with high methane yield and VS reduction.
Zhang, H X
2008-01-01
An innovative approach for total maximum daily load (TMDL) allocation and implementation is the watershed-based pollutant trading. Given the inherent scientific uncertainty for the tradeoffs between point and nonpoint sources, setting of trading ratios can be a contentious issue and was already listed as an obstacle by several pollutant trading programs. One of the fundamental reasons that a trading ratio is often set higher (e.g. greater than 2) is to allow for uncertainty in the level of control needed to attain water quality standards, and to provide a buffer in case traded reductions are less effective than expected. However, most of the available studies did not provide an approach to explicitly address the determination of trading ratio. Uncertainty analysis has rarely been linked to determination of trading ratio.This paper presents a practical methodology in estimating "equivalent trading ratio (ETR)" and links uncertainty analysis with trading ratio determination from TMDL allocation process. Determination of ETR can provide a preliminary evaluation of "tradeoffs" between various combination of point and nonpoint source control strategies on ambient water quality improvement. A greater portion of NPS load reduction in overall TMDL load reduction generally correlates with greater uncertainty and thus requires greater trading ratio. The rigorous quantification of trading ratio will enhance the scientific basis and thus public perception for more informed decision in overall watershed-based pollutant trading program.
Artificial Neural Network Maximum Power Point Tracker for Solar Electric Vehicle
Theodore Amissah OCRAN; CAO Junyi; CAO Binggang; SUN Xinghua
2005-01-01
This paper proposes an artificial neural network maximum power point tracker (MPPT) for solar electric vehicles. The MPPT is based on a highly efficient boost converter with insulated gate bipolar transistor (IGBT) power switch. The reference voltage for MPPT is obtained by artificial neural network (ANN) with gradient descent momentum algorithm. The tracking algorithm changes the duty-cycle of the converter so that the PV-module voltage equals the voltage corresponding to the MPPT at any given insolation, temperature, and load conditions. For fast response, the system is implemented using digital signal processor (DSP). The overall system stability is improved by including a proportional-integral-derivative (PID) controller, which is also used to match the reference and battery voltage levels. The controller, based on the information supplied by the ANN, generates the boost converter duty-cycle. The energy obtained is used to charge the lithium ion battery stack for the solar vehicle. The experimental and simulation results show that the proposed scheme is highly efficient.
Simons, Frederik J
2012-01-01
Topography and gravity are geophysical fields whose joint statistical structure derives from interface-loading processes modulated by the underlying mechanics of isostatic and flexural compensation in the shallow lithosphere. Under this dual statistical-mechanistic viewpoint an estimation problem can be formulated where the knowns are topography and gravity and the principal unknown the elastic flexural rigidity of the lithosphere. In the guise of an equivalent "effective elastic thickness", this important, geographically varying, structural parameter has been the subject of many interpretative studies, but precisely how well it is known or how best it can be found from the data, abundant nonetheless, has remained contentious and unresolved throughout the last few decades of dedicated study. The popular methods whereby admittance or coherence, both spectral measures of the relation between gravity and topography, are inverted for the flexural rigidity, have revealed themselves to have insufficient power to in...
Power amplification in an isolated muscle-tendon unit is load dependent.
Sawicki, Gregory S; Sheppard, Peter; Roberts, Thomas J
2015-11-01
During rapid movements, tendons can act like springs, temporarily storing work done by muscles and then releasing it to power body movements. For some activities, such as frog jumping, energy is released from tendon much more rapidly than it is stored, thus amplifying muscle power output. The period during which energy is loaded into a tendon by muscle work may be aided by a catch mechanism that restricts motion, but theoretical studies indicate that power can be amplified in a muscle-tendon load system even in the absence of a catch. To explore the limits of power amplification with and without a catch, we studied the bullfrog plantaris muscle-tendon during in vitro contractions. A novel servomotor controller allowed us to measure muscle-tendon unit (MTU) mechanical behavior during contractions against a variety of simulated inertial-gravitational loads, ranging from zero to 1× the peak isometric force of the muscle. Power output of the MTU system was load dependent and power amplification occurred only at intermediate loads, reaching ∼1.3× the peak isotonic power output of the muscle. With a simulated anatomical catch mechanism in place, the highest power amplification occurred at the lowest loads, with a maximum amplification of more than 4× peak isotonic muscle power. At higher loads, the benefits of a catch for MTU performance diminished sharply, suggesting that power amplification >2.5× may come at the expense of net mechanical work delivered to the load. © 2015. Published by The Company of Biologists Ltd.
Y. Labbi
2015-08-01
Full Text Available Photovoltaic electricity is seen as an important source of renewable energy. The photovoltaic array is an unstable source of power since the peak power point depends on the temperature and the irradiation level. A maximum peak power point tracking is then necessary for maximum efficiency.In this work, a Particle Swarm Optimization (PSO is proposed for maximum power point tracker for photovoltaic panel, are used to generate the optimal MPP, such that solar panel maximum power is generated under different operating conditions. A photovoltaic system including a solar panel and PSO MPP tracker is modelled and simulated, it has been has been carried out which has shown the effectiveness of PSO to draw much energy and fast response against change in working conditions.
Power transformer additional load losses separation procedure
Kostić Miloje M.
2011-01-01
Full Text Available The proposed procedure is based on the fact that total transformer losses (PLL1,n, determined by short circuit test, can be separated into two components: the eddy current losses in the windings (PEC1,n and stray flux losses (PSL1,n in iron parts of construction as well as in the transformer tank walls. The total additional load losses, PLLd1 and PLLdh, are determined by short circuit test results, conducted at rated frequency (f1 and at increased harmonic frequency (fh=h*f1. Using so obtained total additional load losses, PLLd1 and PLLdh, which can be expressed in the form PLLdh=PEC1,n*h2 + PSL1,n*h, the corresponding rate additional load losses values PEC1,n and PSL1,n are derived. At the end, for given load with predefined high harmonics content, (Ih/I1n, relative to rated current, the total additional load losses value ΣPLLdh > PLLd1, is found. In such a way all harmonics up to hmax are taken into account.
Accurate Maximum Power Tracking in Photovoltaic Systems Affected by Partial Shading
Pierluigi Guerriero
2015-01-01
Full Text Available A maximum power tracking algorithm exploiting operating point information gained on individual solar panels is presented. The proposed algorithm recognizes the presence of multiple local maxima in the power voltage curve of a shaded solar field and evaluates the coordinated of the absolute maximum. The effectiveness of the proposed approach is evidenced by means of circuit level simulation and experimental results. Experiments evidenced that, in comparison with a standard perturb and observe algorithm, we achieve faster convergence in normal operating conditions (when the solar field is uniformly illuminated and we accurately locate the absolute maximum power point in partial shading conditions, thus avoiding the convergence on local maxima.
Westhoff, M.; Erpicum, S.; Archambeau, P.; Pirotton, M.; Zehe, E.; Dewals, B.
2015-12-01
Power can be performed by a system driven by a potential difference. From a given potential difference, the power that can be subtracted is constraint by the Carnot limit, which follows from the first and second laws of thermodynamics. If the system is such that the flux producing power (with power being the flux times its driving potential difference) also influences the potential difference, a maximum in power can be obtained as a result of the trade-off between the flux and the potential difference. This is referred to as the maximum power principle. It has already been shown that the atmosphere operates close to this maximum power limit when it comes to heat transport from the Equator to the poles, or vertically, from the surface to the atmospheric boundary layer. To reach this state of maximum power, the effective thermal conductivity of the atmosphere is adapted by the creation of convection cells. The aim of this study is to test if the soil's effective hydraulic conductivity also adapts in such a way that it produces maximum power. However, the soil's hydraulic conductivity adapts differently; for example by the creation of preferential flow paths. Here, this process is simulated in a lab experiment, which focuses on preferential flow paths created by piping. In the lab, we created a hydrological analogue to the atmospheric model dealing with heat transport between Equator and poles, with the aim to test if the effective hydraulic conductivity of the sand bed can be predicted with the maximum power principle. The experimental setup consists of two freely draining reservoir connected with each other by a confined aquifer. By adding water to only one reservoir, a potential difference will build up until a steady state is reached. The results will indicate whether the maximum power principle does apply for groundwater flow and how it should be applied. Because of the different way of adaptation of flow conductivity, the results differ from that of the
Comparison of Wind Power and Load Forecasting Error Distributions: Preprint
Hodge, B. M.; Florita, A.; Orwig, K.; Lew, D.; Milligan, M.
2012-07-01
The introduction of large amounts of variable and uncertain power sources, such as wind power, into the electricity grid presents a number of challenges for system operations. One issue involves the uncertainty associated with scheduling power that wind will supply in future timeframes. However, this is not an entirely new challenge; load is also variable and uncertain, and is strongly influenced by weather patterns. In this work we make a comparison between the day-ahead forecasting errors encountered in wind power forecasting and load forecasting. The study examines the distribution of errors from operational forecasting systems in two different Independent System Operator (ISO) regions for both wind power and load forecasts at the day-ahead timeframe. The day-ahead timescale is critical in power system operations because it serves the unit commitment function for slow-starting conventional generators.
Influence of load by high power on the optical coupler
Bednarek, Lukas; Poboril, Radek; Vanderka, Ales; Hajek, Lukas; Nedoma, Jan; Vasinek, Vladimir
2016-12-01
Nowadays, aging of the optical components is a very current topic. Therefore, some investigations are focused on this area, so that the aging of the optical components is accelerated by thermal, high power and gamma load. This paper deals by findings of the influence of the load by laser with high optical power on the transmission parameters of the optical coupler. The investigated coupler has one input and eight outputs (1x8). Load by laser with high optical power is realized using a fiber laser with a cascade configuration EDFA amplifiers. The output power of the amplifier is approximately 250 mW. Duration of the load is moving from 104 hours to 139 hours. After each load, input power and output powers of all branches are measured. Following parameters of the optical coupler are calculated using formulas: the insertion losses of the individual branches, split ratio, total losses, homogeneity of the losses and cross-talk between different branches. All measurements are performed at wavelengths 1310 nm and 1550 nm. Individual optical powers are measured 20 times, due to the exclusion of statistical error of the measurement. After measuring, the coupler is connected to the amplifier for next cycle of the load. The paper contains an evaluation of the results of the coupler before and after four cycles of the burden.
Maximum Power Game as a Physical and Social Extension of Classical Games
Kim, Pilwon
2017-01-01
We consider an electric circuit in which the players participate as resistors and adjust their resistance in pursuit of individual maximum power. The maximum power game(MPG) becomes very complicated in a circuit which is indecomposable into serial/parallel components, yielding a nontrivial power distribution at equilibrium. Depending on the circuit topology, MPG covers a wide range of phenomena: from a social dilemma in which the whole group loses to a well-coordinated situation in which the individual pursuit of power promotes the collective outcomes. We also investigate a situation where each player in the circuit has an intrinsic heat waste. Interestingly, it is this individual inefficiency which can keep them from the collective failure in power generation. When coping with an efficient opponent with small intrinsic resistance, a rather inefficient player gets more power than efficient one. A circuit with multiple voltage inputs forms the network-based maximum power game. One of our major interests is to figure out, in what kind of the networks the pursuit for private power leads to greater total power. It turns out that the circuits with the scale-free structure is one of the good candidates which generates as much power as close to the possible maximum total. PMID:28272544
Maximum Power Game as a Physical and Social Extension of Classical Games
Kim, Pilwon
2017-03-01
We consider an electric circuit in which the players participate as resistors and adjust their resistance in pursuit of individual maximum power. The maximum power game(MPG) becomes very complicated in a circuit which is indecomposable into serial/parallel components, yielding a nontrivial power distribution at equilibrium. Depending on the circuit topology, MPG covers a wide range of phenomena: from a social dilemma in which the whole group loses to a well-coordinated situation in which the individual pursuit of power promotes the collective outcomes. We also investigate a situation where each player in the circuit has an intrinsic heat waste. Interestingly, it is this individual inefficiency which can keep them from the collective failure in power generation. When coping with an efficient opponent with small intrinsic resistance, a rather inefficient player gets more power than efficient one. A circuit with multiple voltage inputs forms the network-based maximum power game. One of our major interests is to figure out, in what kind of the networks the pursuit for private power leads to greater total power. It turns out that the circuits with the scale-free structure is one of the good candidates which generates as much power as close to the possible maximum total.
Recent advance on the efficiency at maximum power of heat engines
Tu Zhan-Chun
2012-01-01
This review reports several key advances on the theoretical investigations of efficiency at maximum power of heat engines in the past five years.The analytical results of efficiency at maximum power for the Curzon-Ahlborn heat engine,the stochastic heat engine constructed from a Brownian particle,and Feynman's ratchet as a heat engine are presented.It is found that:the efficiency at maximum power exhibits universal behavior at small relative temperature differences; the lower and the upper bounds might exist under quite general conditions; and the problem of efficiency at maximum power comes down to seeking for the minimum irreversible entropy production in each finite-time isothermal process for a given time.
Holomorphic Embedded Load Flow for autonomous spacecraft power systems Project
National Aeronautics and Space Administration — The Holomorphic Embedding Load Flow Method (HELM) is a breakthrough that brings significant advances to the field of power systems. It provides a non-iterative...
Maximum Power Point Tracking of Photovoltaic System for Traffic Light Application
Riza Muhida
2013-07-01
Full Text Available Photovoltaic traffic light system is a significant application of renewable energy source. The development of the system is an alternative effort of local authority to reduce expenditure for paying fees to power supplier which the power comes from conventional energy source. Since photovoltaic (PV modules still have relatively low conversion efficiency, an alternative control of maximum power point tracking (MPPT method is applied to the traffic light system. MPPT is intended to catch up the maximum power at daytime in order to charge the battery at the maximum rate in which the power from the battery is intended to be used at night time or cloudy day. MPPT is actually a DC-DC converter that can step up or down voltage in order to achieve the maximum power using Pulse Width Modulation (PWM control. From experiment, we obtained the voltage of operation using MPPT is at 16.454 V, this value has error of 2.6%, if we compared with maximum power point voltage of PV module that is 16.9 V. Based on this result it can be said that this MPPT control works successfully to deliver the power from PV module to battery maximally.
Overview of High Power Vacuum Dry RF Load Designs
Krasnykh, Anatoly [SLAC National Accelerator Lab., Menlo Park, CA (United States)
2015-08-27
A specific feature of RF linacs based on the pulsed traveling wave (TW) mode of operation is that only a portion of the RF energy is used for the beam acceleration. The residual RF energy has to be terminated into an RF load. Higher accelerating gradients require higher RF sources and RF loads, which can stably terminate the residual RF power. RF feeders (from the RF source though the accelerating section to the load) are vacuumed to transmit multi-megawatt high power RF. This overview will outline vacuumed RF loads only. A common method to terminate multi-MW RF power is to use circulated water (or other liquid) as an absorbing medium. A solid dielectric interface (a high quality ceramic) is required to separate vacuum and liquid RF absorber mediums. Using such RF load approaches in TW linacs is troubling because there is a fragile ceramic window barrier and a failure could become catastrophic for linac vacuum and RF systems. Traditional loads comprising of a ceramic disk have limited peak and average power handling capability and are therefore not suitable for high gradient TW linacs. This overview will focus on ''vacuum dry'' or ''all-metal'' loads that do not employ any dielectric interface between vacuum and absorber. The first prototype is an original design of RF loads for the Stanford Two-Mile Accelerator.
Loading guide for oil-immersed power transformers
International Electrotechnical Commission. Geneva
1991-01-01
Provides recommendations for the specification and loading of power transformers complying with IEC 60076, from the point of view of operating temperatures and thermal ageing. Gives recommendations for loading above the name-plate rating and guidance for the planner to choose rated quantities for new installations.
Hu, Weihao; Chen, Zhe; Bak-Jensen, Birgitte
2010-01-01
and may represent the future of electricity markets in some ways, is chosen as the studied power system in this paper. A distribution system where wind power capacity is 126% of maximum loads is chosen as the study case. This paper presents a nonlinear load optimization method to real-time power price...... for demand side management in order to save the energy costs as much as possible. Simulation results show that the optimal load response to a real-time electricity price has some good impacts on power system constraints in a distribution system with high wind power penetrations....... for demand side management generates different load profiles and may have some impacts on power system constraints, such as voltage limits and capacity limits. The western Danish power system, which is currently the grid area in the world that has the largest share of wind power in its generation profiles...
Power output in vertical jumps: Does optimum loading depend on activity profiles?
Pazin, Nemanja; Berjan, Bobana; Nedeljkovic, Aleksandar; Markovic, Goran; Jaric, Slobodan
2013-01-01
The previously proposed Maximum Dynamic Output hypothesis (MDO; i.e. the optimum load for maximizing the power output during jumping is one's own body) was tested on individuals of various activity profiles. Forty males (10 strength-trained athletes, 10 speed-trained athletes, 10 physically active non-athletes, and 10 sedentary individuals) performed different vertical jumps on a force plate while a pulley system was used to either reduce or increase the subject's body weight by 10–30%. As expected, an increase in external loading resulted in a significant increase (p < 0.001) in force output and a concomitant decrease of peak jumping velocity in all groups of participants. The main finding, however, was that all groups revealed the maximum peak and mean power output at approximately the subjects’ own body weight although their weight represented prominently different percentage of their maximum dynamic strength. While a significant (p < 0.05), albeit moderate, 'group × load' interaction in one jump was observed for the peak power output, the individual optimum load for maximizing the power output number did not differ among the groups. Although apparently further research on various types of movements is needed, the present results provide, so far, the strongest support of the MDO hypothesis. PMID:22864398
Improved Reliability of Single-Phase PV Inverters by Limiting the Maximum Feed-in Power
Yang, Yongheng; Wang, Huai; Blaabjerg, Frede
2014-01-01
. The CPG control strategy is activated only when the DC input power from PV panels exceeds a specific power limit. It enables to limit the maximum feed-in power to the electric grids and also to improve the utilization of PV inverters. As a further study, this paper investigates the reliability performance...... of the power devices (e.g. IGBTs) used in PV inverters with the CPG control under different feed-in power limits. A long-term mission profile (i.e. solar irradiance and ambient temperature) based stress analysis approach is extended and applied to obtain the yearly electrical and thermal stresses of the power...
Extension Sliding Mode Controller for Maximum Power Point Tracking of Hydrogen Fuel Cells
Meng-Hui Wang
2013-01-01
Full Text Available Fuel cells (FCs are characterized by low pollution, low noise, and high efficiency. However, the voltage-current response of an FC is nonlinear, with the result that there exists just one operating point which maximizes the output power given a particular set of operating conditions. Accordingly, the present study proposes a maximum power point tracking (MPPT control scheme based on extension theory to stabilize the output of an FC at the point of maximum power. The simulation results confirm the ability of the controller to stabilize the output power at the maximum power point despite sudden changes in the temperature, hydrogen pressure, and membrane water content. Moreover, the transient response time of the proposed controller is shown to be faster than that of existing sliding mode (SM and extremum seeking (ES controllers.
Knott, Arnold; Petersen, Lars Press
2013-01-01
Power supply pumping is generated by switch-mode audio power amplifiers in half-bridge configuration, when they are driving energy back into their source. This leads in most designs to a rising rail voltage and can be destructive for either the decoupling capacitors, the rectifier diodes...... in the power supply or the power stage of the amplifier. Therefore precautions are taken by the amplifier and power supply designer to avoid those effects. Existing power supply pumping models are based on an ohmic load attached to the amplifier. This paper shows the analytical derivation of the resulting...... waveforms and extends the model to loudspeaker loads. Measurements verify, that the amount of supply pumping is reduced by a factor of 4 when comparing the nominal resistive load to a loudspeaker. A simplified and more accurate model is proposed and the influence of supply pumping on the audio performance...
Short-term Power Load Forecasting Based on Gray Theory
Cui Herui
2013-11-01
Full Text Available Power load forecasting provides the basis for the preparation of power planning, especially the accurate short-term power load forecasting. It can formulate power rationing program of area load reliably and timely, to maintain the normal production and life. This article describes the gray prediction method, and improves GM (1,1 model via processing the original data sequence smoothly, using the correction model of parameteramending parameter values, adding the residual model, and also applying the idea of the metabolism. It conducts an empirical analysis of the 10KV large cable of Guigang Power Supply Bureau in Nan Ping, and verifies the limitations of ordinary gray theory. The improved gray model has a higher prediction accuracy than the conventional GM (1,1 model.
L. M. Miller
2010-09-01
Full Text Available The availability of wind power for renewable energy extraction is ultimately limited by how much kinetic energy is generated by natural processes within the Earth system and by fundamental limits of how much of the wind power can be extracted. Here we use these considerations to provide a maximum estimate of wind power availability over land. We use three different methods. First, we use simple, established estimates of the energetics of the atmospheric circulation, which yield about 38 TW of wind power available for extraction. Second, we set up a simple momentum balance model to estimate maximum extractability which we then apply to reanalysis climate data, yielding an estimate of 17 TW. Finally, we perform climate model simulations in which we extract different amounts of momentum from the atmospheric boundary layer to obtain a maximum estimate of how much power can be extracted, yielding 36 TW. These three methods consistently yield maximum estimates in the range of 17–38 TW and are notably less than recent estimates that claim abundant wind power availability. Furthermore, we show with the climate model simulations that the climatic effects at maximum wind power extraction are similar in magnitude to those associated with a doubling of atmospheric CO_{2}. We conclude that in order to understand fundamental limits to renewable energy resources, as well as the impacts of their utilization, it is imperative to use a thermodynamic, Earth system perspective, rather than engineering specifications of the latest technology.
A thermoelectric generator using loop heat pipe and design match for maximum-power generation
Huang, Bin-Juine
2015-09-05
The present study focuses on the thermoelectric generator (TEG) using loop heat pipe (LHP) and design match for maximum-power generation. The TEG uses loop heat pipe, a passive cooling device, to dissipate heat without consuming power and free of noise. The experiments for a TEG with 4W rated power show that the LHP performs very well with overall thermal resistance 0.35 K W-1, from the cold side of TEG module to the ambient. The LHP is able to dissipate heat up to 110W and is maintenance free. The TEG design match for maximum-power generation, called “near maximum-power point operation (nMPPO)”, is studied to eliminate the MPPT (maximum-power point tracking controller). nMPPO is simply a system design which properly matches the output voltage of TEG with the battery. It is experimentally shown that TEG using design match for maximum-power generation (nMPPO) performs better than TEG with MPPT.
Xuan Guo
2016-01-01
Full Text Available The theoretical formula of the maximum internal forces for circular tunnel lining structure under impact loads of the underground is deduced in this paper. The internal force calculation formula under different equivalent forms of impact pseudostatic loads is obtained. Furthermore, by comparing the theoretical solution with the measured data of the top blasting model test of circular formula under different equivalent forms of impact pseudostatic loads are obtained. Furthermore, by comparing the theoretical solution with the measured data of the top blasting model test of circular tunnel, it is found that the proposed theoretical results accord with the experimental values well. The corresponding equivalent impact pseudostatic triangular load is the most realistic pattern of all test equivalent forms. The equivalent impact pseudostatic load model and maximum solution of the internal force for tunnel lining structure are partially verified.
neural network based load frequency control for restructuring power ...
2012-03-01
Mar 1, 2012 ... the system in the back propagation chain used in controller training. For this ... power systems. Different types of controllers ... role to allow power exchanges and to supply bet- ter conditions for the ... To solve all these problems in the above men- ..... term load forecasting using generalized neural network ...
Technical evaluation of a total maximum daily load model for Upper Klamath and Agency Lakes, Oregon
Wood, Tamara M.; Wherry, Susan A.; Carter, James L.; Kuwabara, James S.; Simon, Nancy S.; Rounds, Stewart A.
2013-01-01
We reviewed a mass balance model developed in 2001 that guided establishment of the phosphorus total maximum daily load (TMDL) for Upper Klamath and Agency Lakes, Oregon. The purpose of the review was to evaluate the strengths and weaknesses of the model and to determine whether improvements could be made using information derived from studies since the model was first developed. The new data have contributed to the understanding of processes in the lakes, particularly internal loading of phosphorus from sediment, and include measurements of diffusive fluxes of phosphorus from the bottom sediments, groundwater advection, desorption from iron oxides at high pH in a laboratory setting, and estimates of fluxes of phosphorus bound to iron and aluminum oxides. None of these processes in isolation, however, is large enough to account for the episodically high values of whole-lake internal loading calculated from a mass balance, which can range from 10 to 20 milligrams per square meter per day for short periods. The possible role of benthic invertebrates in lake sediments in the internal loading of phosphorus in the lake has become apparent since the development of the TMDL model. Benthic invertebrates can increase diffusive fluxes several-fold through bioturbation and biodiffusion, and, if the invertebrates are bottom feeders, they can recycle phosphorus to the water column through metabolic excretion. These organisms have high densities (1,822–62,178 individuals per square meter) in Upper Klamath Lake. Conversion of the mean density of tubificid worms (Oligochaeta) and chironomid midges (Diptera), two of the dominant taxa, to an areal flux rate based on laboratory measurements of metabolic excretion of two abundant species suggested that excretion by benthic invertebrates is at least as important as any of the other identified processes for internal loading to the water column. Data from sediment cores collected around Upper Klamath Lake since the development of the
Cisneros, Rafael; Gao, Rui; Ortega, Romeo; Husain, Iqbal
2016-10-01
The present paper proposes a maximum power extraction control for a wind system consisting of a turbine, a permanent magnet synchronous generator, a rectifier, a load and one constant voltage source, which is used to form the DC bus. We propose a linear PI controller, based on passivity, whose stability is guaranteed under practically reasonable assumptions. PI structures are widely accepted in practice as they are easier to tune and simpler than other existing model-based methods. Real switching based simulations have been performed to assess the performance of the proposed controller.
A Hybrid Maximum Power Point Tracking Method for Automobile Exhaust Thermoelectric Generator
Quan, Rui; Zhou, Wei; Yang, Guangyou; Quan, Shuhai
2016-08-01
To make full use of the maximum output power of automobile exhaust thermoelectric generator (AETEG) based on Bi2Te3 thermoelectric modules (TEMs), taking into account the advantages and disadvantages of existing maximum power point tracking methods, and according to the output characteristics of TEMs, a hybrid maximum power point tracking method combining perturb and observe (P&O) algorithm, quadratic interpolation and constant voltage tracking method was put forward in this paper. Firstly, it searched the maximum power point with P&O algorithms and a quadratic interpolation method, then, it forced the AETEG to work at its maximum power point with constant voltage tracking. A synchronous buck converter and controller were implemented in the electric bus of the AETEG applied in a military sports utility vehicle, and the whole system was modeled and simulated with a MATLAB/Simulink environment. Simulation results demonstrate that the maximum output power of the AETEG based on the proposed hybrid method is increased by about 3.0% and 3.7% compared with that using only the P&O algorithm and the quadratic interpolation method, respectively. The shorter tracking time is only 1.4 s, which is reduced by half compared with that of the P&O algorithm and quadratic interpolation method, respectively. The experimental results demonstrate that the tracked maximum power is approximately equal to the real value using the proposed hybrid method,and it can preferentially deal with the voltage fluctuation of the AETEG with only P&O algorithm, and resolve the issue that its working point can barely be adjusted only with constant voltage tracking when the operation conditions change.
A Hybrid Maximum Power Point Tracking Method for Automobile Exhaust Thermoelectric Generator
Quan, Rui; Zhou, Wei; Yang, Guangyou; Quan, Shuhai
2017-05-01
To make full use of the maximum output power of automobile exhaust thermoelectric generator (AETEG) based on Bi2Te3 thermoelectric modules (TEMs), taking into account the advantages and disadvantages of existing maximum power point tracking methods, and according to the output characteristics of TEMs, a hybrid maximum power point tracking method combining perturb and observe (P&O) algorithm, quadratic interpolation and constant voltage tracking method was put forward in this paper. Firstly, it searched the maximum power point with P&O algorithms and a quadratic interpolation method, then, it forced the AETEG to work at its maximum power point with constant voltage tracking. A synchronous buck converter and controller were implemented in the electric bus of the AETEG applied in a military sports utility vehicle, and the whole system was modeled and simulated with a MATLAB/Simulink environment. Simulation results demonstrate that the maximum output power of the AETEG based on the proposed hybrid method is increased by about 3.0% and 3.7% compared with that using only the P&O algorithm and the quadratic interpolation method, respectively. The shorter tracking time is only 1.4 s, which is reduced by half compared with that of the P&O algorithm and quadratic interpolation method, respectively. The experimental results demonstrate that the tracked maximum power is approximately equal to the real value using the proposed hybrid method,and it can preferentially deal with the voltage fluctuation of the AETEG with only P&O algorithm, and resolve the issue that its working point can barely be adjusted only with constant voltage tracking when the operation conditions change.
Economic total maximum daily load for watershed-based pollutant trading.
Zaidi, A Z; deMonsabert, S M
2015-04-01
Water quality trading (WQT) is supported by the US Environmental Protection Agency (USEPA) under the framework of its total maximum daily load (TMDL) program. An innovative approach is presented in this paper that proposes post-TMDL trade by calculating pollutant rights for each pollutant source within a watershed. Several water quality trading programs are currently operating in the USA with an objective to achieve overall pollutant reduction impacts that are equivalent or better than TMDL scenarios. These programs use trading ratios for establishing water quality equivalence among pollutant reductions. The inbuilt uncertainty in modeling the effects of pollutants in a watershed from both the point and nonpoint sources on receiving waterbodies makes WQT very difficult. A higher trading ratio carries with it increased mitigation costs, but cannot ensure the attainment of the required water quality with certainty. The selection of an applicable trading ratio, therefore, is not a simple process. The proposed approach uses an Economic TMDL optimization model that determines an economic pollutant reduction scenario that can be compared with actual TMDL allocations to calculate selling/purchasing rights for each contributing source. The methodology is presented using the established TMDLs for the bacteria (fecal coliform) impaired Muddy Creek subwatershed WAR1 in Rockingham County, Virginia, USA. Case study results show that an environmentally and economically superior trading scenario can be realized by using Economic TMDL model or any similar model that considers the cost of TMDL allocations.
Tracking the global maximum power point of PV arrays under partial shading conditions
Fennich, Meryem
This thesis presents the theoretical and simulation studies of the global maximum power point tracking (MPPT) for photovoltaic systems under partial shading. The main goal is to track the maximum power point of the photovoltaic module so that the maximum possible power can be extracted from the photovoltaic panels. When several panels are connected in series with some of them shaded partially either due to clouds or shadows from neighboring buildings, several local maxima appear in the power vs. voltage curve. A power increment based MPPT algorithm is effective in identifying the global maximum from the several local maxima. Several existing MPPT algorithms are explored and the state-of-the-art power increment method is simulated and tested for various partial shading conditions. The current-voltage and power-voltage characteristics of the PV model are studied under different partial shading conditions, along with five different cases demonstrating how the MPPT algorithm performs when shading switches from one state to another. Each case is supplemented with simulation results. The method of tracking the Global MPP is based on controlling the DC-DC converter connected to the output of the PV array. A complete system simulation including the PV array, the direct current to direct current (DC-DC) converter and the MPPT is presented and tested using MATLAB software. The simulation results show that the MPPT algorithm works very well with the buck converter, while the boost converter needs further changes and implementation.
Evaluation of Load Rejection to house load test at 50% power for UCN 3
Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun [Korea Power Engineering Company, Inc., Seoul (Korea, Republic of); Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool [Korea Electric Power Corporation, Taejon (Korea, Republic of)
1998-12-31
The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as the completeness of the plant design. 3 refs., 8 figs., 1 tab. (Author)
Ma, Ke; Liserre, Marco; Blaabjerg, Frede;
2015-01-01
As a key component in the wind turbine system, the power electronic converter and its power semiconductors suffer from complicated power loadings related to environment, and are proven to have high failure rates. Therefore, correct lifetime estimation of wind power converter is crucial...... for the reliability improvement and also for cost reduction of wind power technology. Unfortunately, the existing lifetime estimation methods for the power electronic converter are not yet suitable in the wind power application, because the comprehensive mission profiles are not well specified and included....... Consequently, a relative more advanced approach is proposed in this paper, which is based on the loading and strength analysis of devices and takes into account different time constants of the thermal behaviors in power converter. With the established methods for loading and lifetime estimation for power...
L. M. Miller
2011-02-01
Full Text Available The availability of wind power for renewable energy extraction is ultimately limited by how much kinetic energy is generated by natural processes within the Earth system and by fundamental limits of how much of the wind power can be extracted. Here we use these considerations to provide a maximum estimate of wind power availability over land. We use several different methods. First, we outline the processes associated with wind power generation and extraction with a simple power transfer hierarchy based on the assumption that available wind power will not geographically vary with increased extraction for an estimate of 68 TW. Second, we set up a simple momentum balance model to estimate maximum extractability which we then apply to reanalysis climate data, yielding an estimate of 21 TW. Third, we perform general circulation model simulations in which we extract different amounts of momentum from the atmospheric boundary layer to obtain a maximum estimate of how much power can be extracted, yielding 18–34 TW. These three methods consistently yield maximum estimates in the range of 18–68 TW and are notably less than recent estimates that claim abundant wind power availability. Furthermore, we show with the general circulation model simulations that some climatic effects at maximum wind power extraction are similar in magnitude to those associated with a doubling of atmospheric CO_{2}. We conclude that in order to understand fundamental limits to renewable energy resources, as well as the impacts of their utilization, it is imperative to use a "top-down" thermodynamic Earth system perspective, rather than the more common "bottom-up" engineering approach.
Varactor Modelling for Power Factor Correction in a Varying Load
Agwu D. D.
2016-06-01
Full Text Available : For efficient system operation, it is desirable to keep the power factor at, or very close to unity. One of the very often used methods is application of suitable power factor correction technology. Capacitors are good candidate for constant load power factor correction due to suitability and cost effectiveness. However for varying loads, synchronous condensers are preferred despite having high initial cost as a result of their being able to supply varying leading or lagging reactive power; according to their field excitation. Due to the high acquisition and operation cost of synchronous condensers, this paper presents varactors as a possible alternative for power factor correction. These are diodes that vary their capacitances and leading reactive power according to supply voltage. Applying this involves looking at variation of power factor with supply voltage; and the option of aggregating and harnessing the junction capacitance of varactors for power factor correction of varying loads at low voltage AC levels. This innovation may lead to great improvement in distribution systems requiring quality power supply
A Beacon Transmission Power Control Algorithm Based on Wireless Channel Load Forecasting in VANETs.
Mo, Yuanfu; Yu, Dexin; Song, Jun; Zheng, Kun; Guo, Yajuan
2015-01-01
In a vehicular ad hoc network (VANET), the periodic exchange of single-hop status information broadcasts (beacon frames) produces channel loading, which causes channel congestion and induces information conflict problems. To guarantee fairness in beacon transmissions from each node and maximum network connectivity, adjustment of the beacon transmission power is an effective method for reducing and preventing channel congestion. In this study, the primary factors that influence wireless channel loading are selected to construct the KF-BCLF, which is a channel load forecasting algorithm based on a recursive Kalman filter and employs multiple regression equation. By pre-adjusting the transmission power based on the forecasted channel load, the channel load was kept within a predefined range; therefore, channel congestion was prevented. Based on this method, the CLF-BTPC, which is a transmission power control algorithm, is proposed. To verify KF-BCLF algorithm, a traffic survey method that involved the collection of floating car data along a major traffic road in Changchun City is employed. By comparing this forecast with the measured channel loads, the proposed KF-BCLF algorithm was proven to be effective. In addition, the CLF-BTPC algorithm is verified by simulating a section of eight-lane highway and a signal-controlled urban intersection. The results of the two verification process indicate that this distributed CLF-BTPC algorithm can effectively control channel load, prevent channel congestion, and enhance the stability and robustness of wireless beacon transmission in a vehicular network.
A Beacon Transmission Power Control Algorithm Based on Wireless Channel Load Forecasting in VANETs
Mo, Yuanfu; Yu, Dexin; Song, Jun; Zheng, Kun; Guo, Yajuan
2015-01-01
In a vehicular ad hoc network (VANET), the periodic exchange of single-hop status information broadcasts (beacon frames) produces channel loading, which causes channel congestion and induces information conflict problems. To guarantee fairness in beacon transmissions from each node and maximum network connectivity, adjustment of the beacon transmission power is an effective method for reducing and preventing channel congestion. In this study, the primary factors that influence wireless channel loading are selected to construct the KF-BCLF, which is a channel load forecasting algorithm based on a recursive Kalman filter and employs multiple regression equation. By pre-adjusting the transmission power based on the forecasted channel load, the channel load was kept within a predefined range; therefore, channel congestion was prevented. Based on this method, the CLF-BTPC, which is a transmission power control algorithm, is proposed. To verify KF-BCLF algorithm, a traffic survey method that involved the collection of floating car data along a major traffic road in Changchun City is employed. By comparing this forecast with the measured channel loads, the proposed KF-BCLF algorithm was proven to be effective. In addition, the CLF-BTPC algorithm is verified by simulating a section of eight-lane highway and a signal-controlled urban intersection. The results of the two verification process indicate that this distributed CLF-BTPC algorithm can effectively control channel load, prevent channel congestion, and enhance the stability and robustness of wireless beacon transmission in a vehicular network. PMID:26571042
A Beacon Transmission Power Control Algorithm Based on Wireless Channel Load Forecasting in VANETs.
Yuanfu Mo
Full Text Available In a vehicular ad hoc network (VANET, the periodic exchange of single-hop status information broadcasts (beacon frames produces channel loading, which causes channel congestion and induces information conflict problems. To guarantee fairness in beacon transmissions from each node and maximum network connectivity, adjustment of the beacon transmission power is an effective method for reducing and preventing channel congestion. In this study, the primary factors that influence wireless channel loading are selected to construct the KF-BCLF, which is a channel load forecasting algorithm based on a recursive Kalman filter and employs multiple regression equation. By pre-adjusting the transmission power based on the forecasted channel load, the channel load was kept within a predefined range; therefore, channel congestion was prevented. Based on this method, the CLF-BTPC, which is a transmission power control algorithm, is proposed. To verify KF-BCLF algorithm, a traffic survey method that involved the collection of floating car data along a major traffic road in Changchun City is employed. By comparing this forecast with the measured channel loads, the proposed KF-BCLF algorithm was proven to be effective. In addition, the CLF-BTPC algorithm is verified by simulating a section of eight-lane highway and a signal-controlled urban intersection. The results of the two verification process indicate that this distributed CLF-BTPC algorithm can effectively control channel load, prevent channel congestion, and enhance the stability and robustness of wireless beacon transmission in a vehicular network.
Overview of Maximum Power Point Tracking Techniques for Photovoltaic Energy Production Systems
Koutroulis, Eftichios; Blaabjerg, Frede
2015-01-01
of photovoltaic sources during stochastically varying solar irradiation and ambient temperature conditions. Thus, the overall efficiency of the photovoltaic energy production system is increased. Numerous techniques have been presented during the last decade for implementing the maximum power point tracking......A substantial growth of the installed photovoltaic systems capacity has occurred around the world during the last decade, thus enhancing the availability of electric energy in an environmentally friendly way. The maximum power point tracking technique enables maximization of the energy production...... process in a photovoltaic system. This article provides an overview of the operating principles of these techniques, which are suited for either uniform or non-uniform solar irradiation conditions. The operational characteristics and implementation requirements of these maximum power point tracking...
Azam Zaka
2014-10-01
Full Text Available This paper is concerned with the modifications of maximum likelihood, moments and percentile estimators of the two parameter Power function distribution. Sampling behavior of the estimators is indicated by Monte Carlo simulation. For some combinations of parameter values, some of the modified estimators appear better than the traditional maximum likelihood, moments and percentile estimators with respect to bias, mean square error and total deviation.
Efficiency at maximum power for an Otto engine with ideal feedback
Wang, Honghui; He, Jizhou; Wang, Jianhui; Wu, Zhaoqi
2016-10-01
We propose an Otto heat engine that undergoes processes involving a special class of feedback and analyze theoretically its response. We use stochastic thermodynamics to determine the performance characteristics of the heat engine and indicate the possibility that its maximum efficiency can surpass the Carnot value. The analytical expression for efficiency at maximum power, including the effects resulting from feedback, reduces to that previously derived based on an engine without feedback.
Power electronics and control techniques for maximum energy harvesting in photovoltaic systems
Femia, Nicola
2012-01-01
Incentives provided by European governments have resulted in the rapid growth of the photovoltaic (PV) market. Many PV modules are now commercially available, and there are a number of power electronic systems for processing the electrical power produced by PV systems, especially for grid-connected applications. Filling a gap in the literature, Power Electronics and Control Techniques for Maximum Energy Harvesting in Photovoltaic Systems brings together research on control circuits, systems, and techniques dedicated to the maximization of the electrical power produced by a photovoltaic (PV) so
Low-load Slow Movement Squat Training Increases Muscle Size and Strength but Not Power.
Usui, S; Maeo, S; Tayashiki, K; Nakatani, M; Kanehisa, H
2016-04-01
We tested a hypothesis that low-load squat training with slow movement and tonic force generation (LST) would increase muscle size and strength but not necessarily power. Healthy young men were assigned to LST [50% one-repetition maximum (1-RM) load, 3 s for lowering/lifting without pause: n=9] or low-load normal speed (LN: 50% 1-RM load, 1 s for lowering/lifting with 1-s pause; n=7) groups. Both groups underwent an 8-week squat training program (10 repetitions/set, 3 sets/day, and 3 days/week) using the assigned methods. Before and after the intervention, quadriceps femoris muscle thickness, maximal torque during isometric hip extension and knee extension, 1-RM squat, lifting power from squatting position and rate of electromyography rise (RER) in knee extensors during the task, leg extension power and vertical jump height were measured. After the intervention, the LN group showed no changes in all the variables. The LST group significantly (Pmuscle thickness (6-10%), isometric hip extension torque (18%) and 1-RM squat (10%), but not isometric knee extension torque, lifting power and RER, leg extension power and vertical jump height. These results suggest that LST can increase muscle size and task-related strength, but has little effect on power production during dynamic explosive movements.
Study on load forecasting to data centers of high power density based on power usage effectiveness
Zhou, C. C.; Zhang, F.; Yuan, Z.; Zhou, L. M.; Wang, F. M.; Li, W.; Yang, J. H.
2016-08-01
There is usually considerable energy consumption in data centers. Load forecasting to data centers is in favor of formulating regional load density indexes and of great benefit to getting regional spatial load forecasting more accurately. The building structure and the other influential factors, i.e. equipment, geographic and climatic conditions, are considered for the data centers, and a method to forecast the load of the data centers based on power usage effectiveness is proposed. The cooling capacity of a data center and the index of the power usage effectiveness are used to forecast the power load of the data center in the method. The cooling capacity is obtained by calculating the heat load of the data center. The index is estimated using the group decision-making method of mixed language information. An example is given to prove the applicability and accuracy of this method.
Procedure for determining maximum sustainable power generated by microbial fuel cells.
Menicucci, Joseph; Beyenal, Haluk; Marsili, Enrico; Veluchamy, Raajaraajan Angathevar; Demir, Goksel; Lewandowski, Zbigniew
2006-02-01
Power generated by microbial fuel cells is computed as a product of current passing through an external resistor and voltage drop across this resistor. If the applied resistance is very low, then high instantaneous power generated by the cell is measured, which is not sustainable; the cell cannot deliver that much power for long periods of time. Since using small electrical resistors leads to erroneous assessment of the capabilities of microbial fuel cells, a question arises: what resistor should be used in such measurements? To address this question, we have defined the sustainable power as the steady state of power delivery by a microbial fuel cell under a given set of conditions and the maximum sustainable power as the highest sustainable power that a microbial fuel cell can deliver under a given set of conditions. Selecting the external resistance that is associated with the maximum sustainable power in a microbial fuel cell (MFC) is difficult because the operator has limited influence on the main factors that control power generation: the rate of charge transfer at the current-limiting electrode and the potential established across the fuel cell. The internal electrical resistance of microbial fuel cells varies, and it depends on the operational conditions of the fuel cell. We have designed an empirical procedure to predict the maximum sustainable power that can be generated by a microbial fuel cell operated under a given set of conditions. Following the procedure, we change the external resistors incrementally, in steps of 500 omega every 10, 60, or 180 s and measure the anode potential, the cathode potential, and the cell current. Power generated in the microbial fuel cell that we were using was limited by the anodic current. The anodic potential was used to determine the condition where the maximum sustainable power is obtained. The procedure is simple, microbial fuel cells can be characterized within an hour, and the results of the measurements can serve
Chen-Han Wu
2011-12-01
Full Text Available Due to Japan’s recent nuclear crisis and petroleum price hikes, the search for renewable energy sources has become an issue of immediate concern. A promising candidate attracting much global attention is solar energy, as it is green and also inexhaustible. A maximum power point tracking (MPPT controller is employed in such a way that the output power provided by a photovoltaic (PV system is boosted to its maximum level. However, in the context of abrupt changes in irradiance, conventional MPPT controller approaches suffer from insufficient robustness against ambient variation, inferior transient response and a loss of output power as a consequence of the long duration required of tracking procedures. Accordingly, in this work the maximum power point tracking is carried out successfully using a sliding mode extremum-seeking control (SMESC method, and the tracking performances of three controllers are compared by simulations, that is, an extremum-seeking controller, a sinusoidal extremum-seeking controller and a sliding mode extremum-seeking controller. Being able to track the maximum power point promptly in the case of an abrupt change in irradiance, the SMESC approach is proven by simulations to be superior in terms of system dynamic and steady state responses, and an excellent robustness along with system stability is demonstrated as well.
Automatic load shedding in multiarea elastic power systems
Di Caprio, U.; Marconato, R.
1979-04-01
A procedure for the design of automatic load shedding in an elastic multiarea power system is proposed. Assuming that the power-frequency transfer functions of the various areas are similar, and that the interconnection network can be approximated by a purely reactive network, separate specifications can be given with regard to the control of the mean-frequency transient and that of the interarea electromechanical oscillations. While the first determines the total load to be shed, the second determines its optimal subdivision in order to maximize the stability margin in the large.
Improving automated load flexibility of nuclear power plants with ALFC
Kuhn, Andreas [AREVA GmbH, Karlstein (Germany). Plant Control/Training; Klaus, Peter [E.ON NPP Isar 2, Essenbach (Germany). Plant Operation/Production Engineering
2016-07-01
In several German and Swiss Nuclear Power Plants with Pressurized Water Reactor (PWR) the control of the reactor power was and will be improved in order to be able to support the energy transition with increasing volatile renewable energy in the grid by flexible load operation according to the need of the load dispatcher (power system stability). Especially regarding the mentioned German NPPs with a nominal electric power of approx. 1,500 MW, the general objectives are the main automated grid relevant operation modes. The new possibilities of digital I and C (as TELEPERM {sup registered} XS) enable the automation of the operating modes provided that manual support is no longer necessary. These possibilities were and will be implemented by AREVA within the ALFC-projects. Manifold adaption algorithms to the reactor physical variations during the nuclear load cycle enable a precise control of the axial power density distribution and of the reactivity management in the reactor core. Finally this is the basis for a highly automated load flexibility with the parallel respect and surveillance of the operational limits of a PWR.
SIMULATING MODEL OF SYSTEM FOR MAXIMUM OUTPUT POWER OF SOLAR BATTERY
Abdul Majid Al-Khatib
2005-01-01
Full Text Available Simulating model and algorithm for control of electric power converter of a solar battery are proposed in the paper. Control device of D.C. step-down converter with pulse-width modulation is designed on microprocessor basis. Simulating model permits to investigate various operational modes of a solar battery, demonstrates a process with maximum power mode and is characterized by convenient user’s interface.
Development of an Intelligent Maximum Power Point Tracker Using an Advanced PV System Test Platform
Spataru, Sergiu; Amoiridis, Anastasios; Beres, Remus Narcis
2013-01-01
The performance of photovoltaic systems is often reduced by the presence of partial shadows. The system efficiency and availability can be improved by a maximum power point tracking algorithm that is able to detect partial shadow conditions and to optimize the power output. This work proposes an ...... photovoltaic inverter system test platform that is able to reproduce realistic partial shadow conditions, both in simulation and on hardware test system....
Analytical expressions for maximum wind turbine average power in a Rayleigh wind regime
Carlin, P.W.
1996-12-01
Average or expectation values for annual power of a wind turbine in a Rayleigh wind regime are calculated and plotted as a function of cut-out wind speed. This wind speed is expressed in multiples of the annual average wind speed at the turbine installation site. To provide a common basis for comparison of all real and imagined turbines, the Rayleigh-Betz wind machine is postulated. This machine is an ideal wind machine operating with the ideal Betz power coefficient of 0.593 in a Rayleigh probability wind regime. All other average annual powers are expressed in fractions of that power. Cases considered include: (1) an ideal machine with finite power and finite cutout speed, (2) real machines operating in variable speed mode at their maximum power coefficient, and (3) real machines operating at constant speed.
Optimal Load Response to Time-of-Use Power Price for Demand Side Management in Denmark
Hu, Weihao; Chen, Zhe; Bak-Jensen, Birgitte
2010-01-01
-of-use power price for demand side management in order to save the energy costs as much as possible. 3 typical different kinds of loads (industrial load, residential load and commercial load) in Denmark are chosen as study cases. The energy costs decrease up to 9.6% with optimal load response to time......-of-use power price for different loads. Simulation results show that the optimal load response to time-of-use power price for demand side management generates different load profiles and reduces the load peaks. This kind of load patterns may also have significant effects on the power system normal operation....
Optimal power flow calculation for power system with UPFC considering load rate equalization
Liu, Jiankun; Chen, Jing; Zhang, Qingsong
2017-06-01
Unified power flow controller (UPFC) device can change system electrical quantity (such as voltage, impedance, phase angle, etc.) rapidly and flexibly under the premise of maintain security, stability and reliability of power system, thus can improve the transmission power and transmission line utilization, so as to enhance the power supply capacity of the power grid. Based on a thorough study of the steady-state model of UPFC, taking load rate equalization as objective function, the optimal power flow model is established with UPFC, and simplified interior point method is used to solve it. Finally, optimal power flow of 24 continuous sections actual data is calculated on a typical day of Nanjing network. The results show that the optimal power flow calculation with UPFC can optimize the load rate equalization on the basis of eliminating line overload, improving the voltage level of local power network.
Klumpner, Christian; Blaabjerg, Frede
2004-01-01
Normally, a power converter has one supply port to connect to the power grid and one or multiple output ports to connect to AC loads that require variable voltage and variable frequency. As the trend on the energy market is towards deregulation, new converter topologies are needed to allow...... independent producers/consumers to connect to multiple distribution grids in order to optimise the electricity price, as this will vary during the day from one power distribution company to another one. It will be needed to have a load that can smoothly adjust the power consumed from each power grid in order...... these fraction power will be a necessary feature on a deregulated energy market. This paper presents a new topology of a power converter based on the Direct Power Conversion concept, which is able to connect to multiple grids and provide complete decoupling between without circulating power between the grids...
Maximum power point tracking for photovoltaic system using model predictive control
Ma, Chao; Li, Ning; Li, Shaoyuan [Shanghai Jiao Tong Univ., Shanghai (China). Key Lab. of System Control and Information Processing
2013-07-01
In this paper, T-G-P model is built to find maximum power point according to light intensity and temperature, making it easier and more clearly for photovoltaic system to track the MPP. A predictive controller considering constraints for safe operation is designed. The simulation results show that the system can track MPP quickly, accurately and effectively.
Review of the maximum power point tracking algorithms for stand-alone photovoltaic systems
Salas, V.; Olias, E.; Barrado, A.; Lazaro, A. [Departamento de Tecnologia Electronica/Grupo de Sistemas Electronicos de Potencia, Universidad Carlos III de Madrid, Avda. de la Universidad, 30-28911 Leganes, Madrid (Spain)
2006-07-06
A survey of the algorithms for seeking the maximum power point (MPP) is proposed. As has been shown, there are many ways of distinguishing and grouping methods that seek the MPP from a photovoltaic (PV) generator. However, in this article they are grouped as either direct or nondirect methods. The indirect methods ('quasi seeks') have the particular feature that the MPP is estimated from the measures of the PV generator's voltage and current PV, the irradiance, or using empiric data, by mathematical expressions of numerical approximations. Therefore, the estimation is carried out for a specific PV generator installed in the system. Thus, they do not obtain the maximum power for any irradiance or temperature and none of them are able to obtain the MPP exactly. Subsequently, they are known as 'quasi seeks'. Nevertheless, the direct methods ('true seeking methods') can also be distinguished. They offer the advantage that they obtain the actual maximum power from the measures of the PV generator's voltage and current PV. In that case, they are suitable for any irradiance and temperature. All algorithms, direct and indirect, can be included in some of the DC/DC converters, Maximum power point trackings (MPPTs), for the stand-alone systems. (author)
Wu, Feilong; He, Jizhou; Ma, Yongli; Wang, Jianhui
2014-12-01
We consider the efficiency at maximum power of a quantum Otto engine, which uses a spin or a harmonic system as its working substance and works between two heat reservoirs at constant temperatures Th and Tc (Otto engine working in the linear-response regime.
Estimation of Maximum Allowable PV Connection to LV Residential Power Networks
Demirok, Erhan; Sera, Dezso; Teodorescu, Remus
2011-01-01
transformer or using solar inverters with new grid support features. This study presents a methodology for the estimation of maximum PV hosting capacity including IEC 60076-7 based thermal model of distribution transformer. Certain part of a real distribution network of Braedstrup suburban area in Denmark...... is used in simulation as a case study model. Furthermore, varying solutions (utilizing thermally upgraded insulation paper in transformers, reactive power services from solar inverters, etc.) are implemented on the network under investigation to examine PV penetration level and finally key results learnt......Maximum photovoltaic (PV) hosting capacity of low voltage (LV) power networks is mainly restricted by either thermal limits of network components or grid voltage quality resulted from high penetration of distributed PV systems. This maximum hosting capacity may be lower than the available solar...
Load flow computations in hybrid transmission - distributed power systems
Wobbes, E.D.; Lahaye, D.J.P.
2013-01-01
We interconnect transmission and distribution power systems and perform load flow computations in the hybrid network. In the largest example we managed to build, fifty copies of a distribution network consisting of fifteen nodes is connected to the UCTE study model, resulting in a system consisting
Cyclodissipativity and Power Factor Improvement for Full Nonlinear Loads
Puerto-Flores, Dunstano del; Ortega, Romeo; Scherpen, Jacquelien M.A.; Edelmayer, András
2010-01-01
In recent research, a cyclodissipativity characterization of the problem of power factor compensation (PFC) for nonlinear loads with non-sinusoidal source voltage has been presented. Using this characterization the classical capacitor and inductor compensators can be interpreted in terms of energy e
Unbalanced Load Simulation of Electronic Power Transformer in Distribution System
Wang Dan; Mao Chengxiong; Lu Jiming; Fan Shu; Cao Jiewei; Wang Ben
2006-01-01
A control scheme of electronic power transformer (EPT) in a three-phase four-wire distribution system, which included an input section, an isolating section and an output section, was researched under unbalanced loads. The simple and appropriate control scheme was developed through analyzing the system requirements of the primary side and the load requirements of the secondary side. In the input section, a dual-loop control in synchronous rotating d-q coordinates was introduced, and in the output section, a dual-loop control based on instantaneous output voltage wasused. Load characteristics of EPT were investigated by using Matlab/Simulink software. Simulation results showed that, with the proposed control scheme, the EPT has good performances and the sinusoidal input current and constant output voltage can be realized under both balanced and unbalanced loads.
Efficiency at and near maximum power of low-dissipation heat engines.
Holubec, Viktor; Ryabov, Artem
2015-11-01
A universality in optimization of trade-off between power and efficiency for low-dissipation Carnot cycles is presented. It is shown that any trade-off measure expressible in terms of efficiency and the ratio of power to its maximum value can be optimized independently of most details of the dynamics and of the coupling to thermal reservoirs. The result is demonstrated on two specific trade-off measures. The first one is designed for finding optimal efficiency for a given output power and clearly reveals diseconomy of engines working at maximum power. As the second example we derive universal lower and upper bounds on the efficiency at maximum trade-off given by the product of power and efficiency. The results are illustrated on a model of a diffusion-based heat engine. Such engines operate in the low-dissipation regime given that the used driving minimizes the work dissipated during the isothermal branches. The peculiarities of the corresponding optimization procedure are reviewed and thoroughly discussed.
Efficiency at and near maximum power of low-dissipation heat engines
Holubec, Viktor; Ryabov, Artem
2015-11-01
A universality in optimization of trade-off between power and efficiency for low-dissipation Carnot cycles is presented. It is shown that any trade-off measure expressible in terms of efficiency and the ratio of power to its maximum value can be optimized independently of most details of the dynamics and of the coupling to thermal reservoirs. The result is demonstrated on two specific trade-off measures. The first one is designed for finding optimal efficiency for a given output power and clearly reveals diseconomy of engines working at maximum power. As the second example we derive universal lower and upper bounds on the efficiency at maximum trade-off given by the product of power and efficiency. The results are illustrated on a model of a diffusion-based heat engine. Such engines operate in the low-dissipation regime given that the used driving minimizes the work dissipated during the isothermal branches. The peculiarities of the corresponding optimization procedure are reviewed and thoroughly discussed.
Alaraj, Muhannad; Radenkovic, Miloje; Park, Jae-Do
2017-02-01
Microbial fuel cells (MFCs) are renewable and sustainable energy sources that can be used for various applications. The MFC output power depends on its biochemical conditions as well as the terminal operating points in terms of output voltage and current. There exists one operating point that gives the maximum possible power from the MFC, maximum power point (MPP), for a given operating condition. However, this MPP may vary and needs to be tracked in order to maintain the maximum power extraction from the MFC. Furthermore, MFC reactors often develop voltage overshoots that cause drastic drops in the terminal voltage, current, and the output power. When the voltage overshoot happens, an additional control measure is necessary as conventional MPPT algorithms will fail because of the change in the voltage-current relationship. In this paper, the extremum seeking (ES) algorithm was used to track the varying MPP and a voltage overshoot avoidance (VOA) algorithm is developed to manage the voltage overshoot conditions. The proposed ES-MPPT with VOA algorithm was able to extract 197.2 mJ during 10-min operation avoiding voltage overshoot, while the ES MPPT-only scheme stopped harvesting after only 18.75 mJ because of the voltage overshoot happened at 0.4 min.
Shahrooz Hajighorbani
2016-01-01
Full Text Available This paper presents a hybrid maximum power point tracking (MPPT method to detect the global maximum power point (GMPP under partially shaded conditions (PSCs, which have more complex characteristics with multiple peak power points. The hybrid method can track the GMPP when a partial shadow occurs either before or after acquiring the MPP under uniform conditions. When PS occurs after obtaining the MPP during uniform conditions, the new operating point should be specified by the modified linear function, which reduces the searching zone of the GMPP and has a significant effect on reducing the reaching time of the GMPP. Simultaneously, the possible MPPs are scanned and stored when shifting the operating point to a new reference voltage. Finally, after determining the possible location of the GMPP, the GMPP is obtained using the modified P&O. Conversely, when PS occurs before obtaining the MPP, the referenced MPP should be specified. Thus, after recognizing the possible location of the GMPP, the modified P&O can be used to obtain the GMPP. The simulation and experimental implementations for the proposed algorithm are performed with different scenarios of shadowing under different irradiations, which clearly indicate that the proposed method is robust and has a fast tracking speed. Moreover, this work presents the load sizing method for PSCs to avoid controller failure when detecting the GMPP. Additionally, in this paper, the user-friendly method for programming the digital signal processing (DSP via Simulink/MATLAB is presented in detail.
DURUSU, A.
2014-08-01
Full Text Available Maximum power point trackers (MPPTs play an essential role in extracting power from photovoltaic (PV panels as they make the solar panels to operate at the maximum power point (MPP whatever the changes of environmental conditions are. For this reason, they take an important place in the increase of PV system efficiency. MPPTs are driven by MPPT algorithms and a number of MPPT algorithms are proposed in the literature. The comparison of the MPPT algorithms in literature are made by a sun simulator based test system under laboratory conditions for short durations. However, in this study, the performances of four most commonly used MPPT algorithms are compared under real environmental conditions for longer periods. A dual identical experimental setup is designed to make a comparison between two the considered MPPT algorithms as synchronized. As a result of this study, the ranking among these algorithms are presented and the results show that Incremental Conductance (IC algorithm gives the best performance.
An improved maximum power point tracking method for a photovoltaic system
Ouoba, David; Fakkar, Abderrahim; El Kouari, Youssef; Dkhichi, Fayrouz; Oukarfi, Benyounes
2016-06-01
In this paper, an improved auto-scaling variable step-size Maximum Power Point Tracking (MPPT) method for photovoltaic (PV) system was proposed. To achieve simultaneously a fast dynamic response and stable steady-state power, a first improvement was made on the step-size scaling function of the duty cycle that controls the converter. An algorithm was secondly proposed to address wrong decision that may be made at an abrupt change of the irradiation. The proposed auto-scaling variable step-size approach was compared to some various other approaches from the literature such as: classical fixed step-size, variable step-size and a recent auto-scaling variable step-size maximum power point tracking approaches. The simulation results obtained by MATLAB/SIMULINK were given and discussed for validation.
Woonki Na
2017-03-01
Full Text Available This paper presents an improved maximum power point tracking (MPPT algorithm using a fuzzy logic controller (FLC in order to extract potential maximum power from photovoltaic cells. The objectives of the proposed algorithm are to improve the tracking speed, and to simultaneously solve the inherent drawbacks such as slow tracking in the conventional perturb and observe (P and O algorithm. The performances of the conventional P and O algorithm and the proposed algorithm are compared by using MATLAB/Simulink in terms of the tracking speed and steady-state oscillations. Additionally, both algorithms were experimentally validated through a digital signal processor (DSP-based controlled-boost DC-DC converter. The experimental results show that the proposed algorithm performs with a shorter tracking time, smaller output power oscillation, and higher efficiency, compared with the conventional P and O algorithm.
Unbounded Binary Search for a Fast and Accurate Maximum Power Point Tracking
Kim, Yong Sin; Winston, Roland
2011-12-01
This paper presents a technique for maximum power point tracking (MPPT) of a concentrating photovoltaic system using cell level power optimization. Perturb and observe (P&O) has been a standard for an MPPT, but it introduces a tradeoff between the tacking speed and the accuracy of the maximum power delivered. The P&O algorithm is not suitable for a rapid environmental condition change by partial shading and self-shading due to its tracking time being linear to the length of the voltage range. Some of researches have been worked on fast tracking but they come with internal ad hoc parameters. In this paper, by using the proposed unbounded binary search algorithm for the MPPT, tracking time becomes a logarithmic function of the voltage search range without ad hoc parameters.
Low-Power Maximum a Posteriori (MAP Algorithm for WiMAX Convolutional Turbo Decoder
Chitralekha Ngangbam
2013-05-01
Full Text Available We propose to design a Low-Power Memory-Reduced Traceback MAP iterative decoding of convolutional turbo code (CTC which has large data access with large memories consumption and verify the functionality by using simulation tool. The traceback maximum a posteriori algorithm (MAP decoding provides the best performance in terms of bit error rate (BER and reduce the power consumption of the state metric cache (SMC without losing the correction performance. The computation and accessing of different metrics reduce the size of the SMC with no requires complicated reversion checker, path selection, and reversion flag cache. Radix-2*2 and radix-4 traceback structures provide a tradeoff between power consumption and operating frequency for double-binary (DB MAP decoding. These two traceback structures achieve an around 25% power reduction of the SMC, and around 12% power reduction of the DB MAP decoders for WiMAX standard
ZHANG Xu-ping; YU Yue-qing
2005-01-01
Optimization of structural parameters aimed at improving the load carrying capacity of spatial flexible redundant manipulators is presented in this paper. In order to increase the ratio of load to mass of robots, the cross-sectional parameters and constructional parameters are optimized respectively. The cross-sectional and configurational parameters are optimized simultaneously. The numerical simulation of a 4R spatial manipulator is performed. The results show that the load capacity of robots has been greatly improved through the optimization strategies proposed in this paper.
On load flow control in electric power systems
Herbig, Arnim
2000-01-01
This dissertation deals with the control of active power flow, or load flow in electric power systems. During the last few years, interest in the possibilities to control the active power flows in transmission systems has increased significantly. There is a number of reasons for this, coming both from the application side - that is, from power system operations - and from the technological side. where advances in power electronics and related technologies have made new system components available. Load flow control is by nature a multi-input multi-output problem, since any change of load flow in one line will be complemented by changes in other lines. Strong cross-coupling between controllable components is to be expected, and the possibility of adverse interactions between these components cannot be rejected straightaway. Interactions with dynamic phenomena in the power system are also a source of concern. Three controllable components are investigated in this thesis, namely the controlled series capacitor (CSC), the phase angle regulator (PAR), and the unified power flow controller (UPFC). Properties and characteristics of these devices axe investigated and discussed. A simple control strategy is proposed. This strategy is then analyzed extensively. Mathematical methods and physical knowledge about the pertinent phenomena are combined, and it is shown that this control strategy can be used for a fairly general class of devices. Computer simulations of the controlled system provide insight into the system behavior in a system of reasonable size. The robustness and stability of the control system are discussed as are its limits. Further, the behavior of the control strategy in a system where the modeling allows for dynamic phenomena are investigated with computer simulations. It is discussed under which circumstances the control action has beneficial or detrimental effect on the system dynamics. Finally, a graphical approach for analyzing the effect of controllers
Optimization Formulations for the Maximum Nonlinear Buckling Load of Composite Structures
Lindgaard, Esben; Lund, Erik
2011-01-01
, benchmarked on a number of numerical examples of laminated composite structures for the maximization of the buckling load considering fiber angle design variables. The optimization formulations are based on either linear or geometrically nonlinear analysis and formulated as mathematical programming problems...... solved using gradient based techniques. The developed local criterion is formulated such it captures nonlinear effects upon loading and proves useful for both analysis purposes and as a criterion for use in nonlinear buckling optimization. © 2010 Springer-Verlag....
2012-11-26
... COMMISSION Preoperational Testing of Onsite Electric Power Systems To Verify Proper Load Group Assignments... Power Systems to Verify Proper Load Group Assignments, Electrical Separation, and Redundancy.'' DG-1294... encompass preoperational testing of electrical power systems used to meet current Station...
Bogaraj T.
2015-09-01
Full Text Available Many parts of remote locations in the world are not electrified even in this Advanced Technology Era. To provide electricity in such remote places renewable hybrid energy systems are very much suitable. In this paper PV/Wind/Battery Hybrid Power System (HPS is considered to provide an economical and sustainable power to a remote load. HPS can supply the maximum power to the load at a particular operating point which is generally called as Maximum Power Point (MPP. Fuzzy Logic based MPPT (FLMPPT control method has been implemented for both Solar and Wind Power Systems. FLMPPT control technique is implemented to generate the optimal reference voltage for the first stage of DC-DC Boost converter in both the PV and Wind energy system. The HPS is tested with variable solar irradiation, temperature, and wind speed. The FLMPPT method is compared with P&O MPPT method. The proposed method provides a good maximum power operation of the hybrid system at all operating conditions. In order to combine both sources, the DC bus voltage is made constant by employing PI Controllers for the second stage of DC-DC Buck-Boost converter in both Solar and Wind Power Systems. Battery Bank is used to store excess power from Renewable Energy Sources (RES and to provide continuous power to load when the RES power is less than load power. A SPWM inverter is designed to convert DC power into AC to supply three phase load. An LC filter is also used at the output of inverter to get sinusoidal current from the PWM inverter. The entire system was modeled and simulated in Matlab/Simulink Environment. The results presented show the validation of the HPS design.
北京电网风电发展与消纳能力%Development and Maximum Accommodating Capacity of Wind Power in Beijing Power Grid
余潇潇; 张璞; 刘兆燕; 左向红; 张凯; 田子婵
2015-01-01
结合北京地区风力资源分布情况及风力发电的并网现状，对北京地区风力发电的发展情况进行了预测。预测内容包括规划风力发电的输出特性，以及“十三五”期间北京地区风力发电的发展情况。提出了一种以电网的负荷特性、常规电源调峰能力、新能源处理特性及外受电力交换情况作为边界条件的风电消纳计算方法。运用该方法对北京电网“十二五”末及“十三五”末对风电的消纳能力进行了计算，并提出了促进北京电网风电发展的相关技术措施。%According to the distribution of wind energy resource and the present situation of wind power integration in Beijing, the forecast of wind power generation development in Beijing power grid was provided, which focused on the output characteristics of the planned wind power projects and the development of wind power generation in Beijing during the 13th national five￣year plan. A calculation method of the maximum proliferation ratio of wind power in Beijing power grid was proposed, whose boundary condition included the load characteristics of grid, the peak shift capability of local power generation plants, the new energy processing features and the power flow exchange limit with the outside grid. The method was used to calculate the maximum penetration ratio of wind power in Beijing power grid during the end of the 12th, 13th national five￣year plan. Finally, this paper suggested some related technical measures to promote the development of wind power in Beijing power grid.
A Maximum Power Point Tracker with Automatic Step Size Tuning Scheme for Photovoltaic Systems
Kuei-Hsiang Chao
2012-01-01
Full Text Available The purpose of this paper is to study on a novel maximum power point tracking (MPPT method for photovoltaic (PV systems. First, the simulation environment for PV systems is constructed by using PSIM software package. A 516 W PV system established with Kyocera KC40T photovoltaic modules is used as an example to finish the simulation of the proposed MPPT method. When using incremental conductance (INC MPPT method, it usually should consider the tradeoff between the dynamic response and the steady-state oscillation, whereas the proposed modified incremental conductance method based on extension theory can automatically adjust the step size to track the maximum power point (MPP of PV array and effectively improve the dynamic response and steady-state performance of the PV systems, simultaneously. Some simulation and experimental results are made to verify that the proposed extension maximum power point tracking method can provide a good dynamic response and steady-state performance for a photovoltaic power generation system.
Perez, Richard
2003-04-01
A load controller and method are provided for maximizing effective capacity of a non-controllable, renewable power supply coupled to a variable electrical load also coupled to a conventional power grid. Effective capacity is enhanced by monitoring power output of the renewable supply and loading, and comparing the loading against the power output and a load adjustment threshold determined from an expected peak loading. A value for a load adjustment parameter is calculated by subtracting the renewable supply output and the load adjustment parameter from the current load. This value is then employed to control the variable load in an amount proportional to the value of the load control parameter when the parameter is within a predefined range. By so controlling the load, the effective capacity of the non-controllable, renewable power supply is increased without any attempt at operational feedback control of the renewable supply. The expected peak loading of the variable load can be dynamically determined within a defined time interval with reference to variations in the variable load.
Optimal Velocity to Achieve Maximum Power Output – Bench Press for Trained Footballers
Richard Billich
2015-03-01
Full Text Available Optimal Velocity to Achieve Maximum Power Output – Bench Press for Trained Footballers In today’s world of strength training there are many myths surrounding effective exercising with the least possible negative effect on one’s health. In this experiment we focus on the finding of a relationship between maximum output, used load and the velocity with which the exercise is performed. The main objective is to find the optimal speed of the exercise motion which would allow us to reach the maximum mechanic muscle output during a bench press exercise. This information could be beneficial to sporting coaches and recreational sportsmen alike in helping them improve the effectiveness of fast strength training. Fifteen football players of the FK Třinec football club participated in the experiment. The measurements were made with the use of 3D cinematic and dynamic analysis, both experimental methods. The research subjects participated in a strength test, in which the mechanic muscle output of 0, 10, 30, 50, 70, 90% and one repetition maximum (1RM was measured. The acquired result values and other required data were modified using Qualisys Track Manager and Visual 3D software (C-motion, Rockville, MD, USA. During the bench press exercise the maximum mechanic muscle output of the set of research subjects was reached at 75% of maximum exercise motion velocity. Optimální rychlost pohybu pro dosažení maxima výstupního výkonu – bench press u trénovaných fotbalistů Dnešní svět silového tréninku přináší řadu mýtů o tom, jak cvičit efektivně a zároveň s co nejmenším negativním vlivem na zdraví člověka. V tomto experimentu se zabýváme nalezením vztahu mezi maximálním výkonem, použitou zátěží a rychlostí. Hlavním úkolem je nalezení optimální rychlosti pohybu pro dosažení maximálního mechanického svalového výkonu při cvičení bench press, což pomůže nejenom trenérům, ale i rekreačním sportovc
Design of a Maximum Power Point Tracker with Simulation, Analysis, and Comparison of Algorithms
2012-12-01
was discussed as well as designed around a single diode model. By modeling the solar array based on measured parameters, the output current and voltage ...Switched Capacitor Buck-Boost Converter for PV Application 11 2.7 A Novel MPPT Charge Regulator for a Photovoltaic Stand-alone Telecommu- nication...Simulink, which includes the solar array, buck converter, and resistive load. . . . . 16 Figure 3.2 The Current versus Voltage and Power versus Voltage
Optimal Power Management Strategy for Energy Storage with Stochastic Loads
Stefano Pietrosanti
2016-03-01
Full Text Available In this paper, a power management strategy (PMS has been developed for the control of energy storage in a system subjected to loads of random duration. The PMS minimises the costs associated with the energy consumption of specific systems powered by a primary energy source and equipped with energy storage, under the assumption that the statistical distribution of load durations is known. By including the variability of the load in the cost function, it was possible to define the optimality criteria for the power flow of the storage. Numerical calculations have been performed obtaining the control strategies associated with the global minimum in energy costs, for a wide range of initial conditions of the system. The results of the calculations have been tested on a MATLAB/Simulink model of a rubber tyre gantry (RTG crane equipped with a flywheel energy storage system (FESS and subjected to a test cycle, which corresponds to the real operation of a crane in the Port of Felixstowe. The results of the model show increased energy savings and reduced peak power demand with respect to existing control strategies, indicating considerable potential savings for port operators in terms of energy and maintenance costs.
Squat jump training at maximal power loads vs. heavy loads: effect on sprint ability.
Harris, Nigel K; Cronin, John B; Hopkins, Will G; Hansen, Keir T
2008-11-01
Training at a load maximizing power output (Pmax) is an intuitively appealing strategy for enhancement of performance that has received little research attention. In this study we identified each subject's Pmax for an isoinertial resistance training exercise used for testing and training, and then we related the changes in strength to changes in sprint performance. The subjects were 18 well-trained rugby league players randomized to two equal-volume training groups for a 7-week period of squat jump training with heavy loads (80% 1RM) or with individually determined Pmax loads (20.0-43.5% 1RM). Performance measures were 1RM strength, maximal power at 55% of pretraining 1RM, and sprint times for 10 and 30 m. Percent changes were standardized to make magnitude-based inferences. Relationships between changes in these variables were expressed as correlations. Sprint times for 10 m showed improvements in the 80% 1RM group (-2.9 +/- 3.2%) and Pmax group (-1.3 +/- 2.2%), and there were similar improvements in 30-m sprint time (-1.9 +/- 2.8 and -1.2 +/- 2.0%, respectively). Differences in the improvements in sprint time between groups were unclear, but improvement in 1RM strength in the 80% 1RM group (15 +/- 9%) was possibly substantially greater than in the Pmax group (11 +/- 8%). Small-moderate negative correlations between change in 1RM and change in sprint time (r approximately -0.30) in the combined groups provided the only evidence of adaptive associations between strength and power outputs, and sprint performance. In conclusion, it seems that training at the load that maximizes individual peak power output for this exercise with a sample of professional team sport athletes was no more effective for improving sprint ability than training at heavy loads, and the changes in power output were not usefully related to changes in sprint ability.
2012-12-01
portable devices where system size and efficiency are the primary design factors. Size and efficiency also govern the use of multiple MPPTs at the sub... mechanisms responsible for the energy losses in a switch-mode converter are the same. They include the components responsible for conduction, capacitor...designed to directly power a load as done in this test. The SPV-1020 may require an appropriate battery charger such as the STEVAL SEA05 battery
Chronic eccentric cycling improves quadriceps muscle structure and maximum cycling power.
Leong, C H; McDermott, W J; Elmer, S J; Martin, J C
2014-06-01
An interesting finding from eccentric exercise training interventions is the presence of muscle hypertrophy without changes in maximum concentric strength and/or power. The lack of improvements in concentric strength and/or power could be due to long lasting suppressive effects on muscle force production following eccentric training. Thus, improvements in concentric strength and/or power might not be detected until muscle tissue has recovered (e. g., several weeks post-training). We evaluated alterations in muscular structure (rectus-femoris, RF, and vastus lateralis, VL, thickness and pennation angles) and maximum concentric cycling power (Pmax) 1-week following 8-weeks of eccentric cycling training (2×/week; 5-10.5 min; 20-55% of Pmax). Pmax was assessed again at 8-weeks post-training. At 1 week post-training, RF and VL thickness increased by 24±4% and 13±2%, respectively, and RF and VL pennation angles increased by 31±4% and 13±1%, respectively (all Peccentric cycling can be a time-effective intervention for improving muscular structure and function in the lower body of healthy individuals. The larger Pmax increase detected at 8-weeks post-training implies that sufficient recovery might be necessary to fully detect changes in muscular power after eccentric cycling training.
Appelbaum, J.; Singer, S.
1989-01-01
A calculation of the starting torque ratio of permanent magnet, series, and shunt-excited dc motors powered by solar cell arrays is presented for two cases, i.e., with and without a maximum-power-point tracker (MPPT). Defining motor torque magnification by the ratio of the motor torque with an MPPT to the motor torque without an MPPT, a magnification of 3 for the permanent magnet motor and a magnification of 7 for both the series and shunt motors are obtained. The study also shows that all motor types are less sensitive to solar insolation variation in systems including MPPTs as compared to systems without MPPTs.
Efficiency at maximum power output of quantum heat engines under finite-time operation
Wang, Jianhui; He, Jizhou; Wu, Zhaoqi
2012-03-01
We study the efficiency at maximum power, ηm, of irreversible quantum Carnot engines (QCEs) that perform finite-time cycles between a hot and a cold reservoir at temperatures Th and Tc, respectively. For QCEs in the reversible limit (long cycle period, zero dissipation), ηm becomes identical to the Carnot efficiency ηC=1-Tc/Th. For QCE cycles in which nonadiabatic dissipation and the time spent on two adiabats are included, the efficiency ηm at maximum power output is bounded from above by ηC/(2-ηC) and from below by ηC/2. In the case of symmetric dissipation, the Curzon-Ahlborn efficiency ηCA=1-Tc/Th is recovered under the condition that the time allocation between the adiabats and the contact time with the reservoir satisfy a certain relation.
Maximum Energy Extraction Control for Wind Power Generation Systems Based on the Fuzzy Controller
Kamal, Elkhatib; Aitouche, Abdel; Mohammed, Walaa; Sobaih, Abdel Azim
2016-10-01
This paper presents a robust controller for a variable speed wind turbine with a squirrel cage induction generator (SCIG). For variable speed wind energy conversion system, the maximum power point tracking (MPPT) is a very important requirement in order to maximize the efficiency. The system is nonlinear with parametric uncertainty and subject to large disturbances. A Takagi-Sugeno (TS) fuzzy logic is used to model the system dynamics. Based on the TS fuzzy model, a controller is developed for MPPT in the presence of disturbances and parametric uncertainties. The proposed technique ensures that the maximum power point (MPP) is determined, the generator speed is controlled and the closed loop system is stable. Robustness of the controller is tested via the variation of model's parameters. Simulation studies clearly indicate the robustness and efficiency of the proposed control scheme compared to other techniques.
Efficiency at maximum power output of quantum heat engines under finite-time operation.
Wang, Jianhui; He, Jizhou; Wu, Zhaoqi
2012-03-01
We study the efficiency at maximum power, η(m), of irreversible quantum Carnot engines (QCEs) that perform finite-time cycles between a hot and a cold reservoir at temperatures T(h) and T(c), respectively. For QCEs in the reversible limit (long cycle period, zero dissipation), η(m) becomes identical to the Carnot efficiency η(C)=1-T(c)/T(h). For QCE cycles in which nonadiabatic dissipation and the time spent on two adiabats are included, the efficiency η(m) at maximum power output is bounded from above by η(C)/(2-η(C)) and from below by η(C)/2. In the case of symmetric dissipation, the Curzon-Ahlborn efficiency η(CA)=1-√(T(c)/T(h)) is recovered under the condition that the time allocation between the adiabats and the contact time with the reservoir satisfy a certain relation.
Hussain Mutlag, Ammar; Mohamed, Azah; Shareef, Hussain
2016-03-01
Maximum power point tracking (MPPT) is normally required to improve the performance of photovoltaic (PV) systems. This paper presents artificial intelligent-based maximum power point tracking (AI-MPPT) by considering three artificial intelligent techniques, namely, artificial neural network (ANN), adaptive neuro fuzzy inference system with seven triangular fuzzy sets (7-tri), and adaptive neuro fuzzy inference system with seven gbell fuzzy sets. The AI-MPPT is designed for the 25 SolarTIFSTF-120P6 PV panels, with the capacity of 3 kW peak. A complete PV system is modelled using 300,000 data samples and simulated in the MATLAB/SIMULINK. The AI-MPPT has been tested under real environmental conditions for two days from 8 am to 18 pm. The results showed that the ANN based MPPT gives the most accurate performance and then followed by the 7-tri-based MPPT.
A maximum power point tracker for photovoltaic energy systems based on fuzzy neural networks
Chun-hua LI; Xin-jian ZHU; Guang-yi CAO; Wan-qi HU; Sheng SUI; Ming-ruo HU
2009-01-01
To extract the maximum power from a photovoltaic (PV) energy system, the real-time maximum power point (MPP) of the PV array must be tracked closely. The non-linear and time-variant characteristics of the PV array and the non-linear and non-minimum phase characteristics of a boost converter make it difficult to track the MPP for traditional control strategies. We propose a fuzzy neural network controller (FNNC), which combines the reasoning capability of fuzzy logical systems and the learning capability of neural networks, to track the MPP. With a derived learning algorithm, the parameters of the FNNC are updated adaptively. A gradient estimator based on a radial basis function neural network is developed to provide the reference information to the FNNC. Simulation results show that the proposed control algorithm provides much better tracking performance compared with the fuzzy logic control algorithm.
Kaiadi, Mehrzad; Tunestål, Per; Johansson, Bengt
2010-01-01
High EGR rates combined with turbocharging has been identified as a promising way to increase the maximum load and efficiency of heavy duty spark ignition Natural Gas engines. With stoichiometric conditions a three way catalyst can be used which means that regulated emissions can be kept at very low levels. Most of the heavy duty NG engines are diesel engines which are converted for SI operation. These engine's components are in common with the diesel-engine which put limits on higher exh...
Bayu Prima Juliansyah Putra; Aulia Siti Aisjah; Syamsul Arifin
2013-01-01
Salah satu aplikasi yang sering digunakan dalam bidang energi terbarukan adalah panel photovoltaic. Panel ini memiliki prinsip kerja berdasarkan efek photovoltaic dimana lempengan logam akan menghasilkan energi listrik apabila diberi intensitas cahaya. Untuk menghasilkan daya keluaran panel yang maksimal, maka diperlukan suatu algoritma yang biasa disebut Maximum Power Point Tracking (MPPT).MPPT yang diterapkan pada sistem photovoltaic berfungsi untuk mengatur nilai tegangan keluaran panel se...
Fast calculation of the maximum power point of photovoltaic generators under partial shading
Carlos Andres Ramos-Paja; Luz Adriana Trejos-Grisales; Javier Herrera-Murcia
2016-01-01
This paper presents a method to calculate the energy production of photovoltaic generators considering partial shading or mismatched conditions. The proposed method is based on the complete one-diode model including the bypass diode in its exponential form, where the current and voltage values of the modules composing the photovoltaic panel array are calculated without using the Lambert-W function. In addition, the method introduces a procedure to calculate the vicinity of the maximum power p...
Efficiency at maximum power output of linear irreversible Carnot-like heat engines.
Wang, Yang; Tu, Z C
2012-01-01
The efficiency at maximum power output of linear irreversible Carnot-like heat engines is investigated based on the assumption that the rate of irreversible entropy production of the working substance in each "isothermal" process is a quadratic form of the heat exchange rate between the working substance and the reservoir. It is found that the maximum power output corresponds to minimizing the irreversible entropy production in two isothermal processes of the Carnot-like cycle, and that the efficiency at maximum power output has the form η(mP)=η(C)/(2-γη(C)), where η(C) is the Carnot efficiency, while γ depends on the heat transfer coefficients between the working substance and two reservoirs. The value of η(mP) is bounded between η(-)≡η(C)/2 and η(+)≡η(C)/(2-η(C)). These results are consistent with those obtained by Chen and Yan [J. Chem. Phys. 90, 3740 (1989)] based on the endoreversible assumption, those obtained by Esposito et al. [Phys. Rev. Lett. 105, 150603 (2010)] based on the low-dissipation assumption, and those obtained by Schmiedl and Seifert [Europhys. Lett. 81, 20003 (2008)] for stochastic heat engines which in fact also satisfy the low-dissipation assumption. Additionally, we find that the endoreversible assumption happens to hold for Carnot-like heat engines operating at the maximum power output based on our fundamental assumption, and that the Carnot-like heat engines that we focused on do not strictly satisfy the low-dissipation assumption, which implies that the low-dissipation assumption or our fundamental assumption is a sufficient but non-necessary condition for the validity of η(mP)=η(C)/(2-γη(C)) as well as the existence of two bounds, η(-)≡η(C)/2 and η(+)≡η(C)/(2-η(C)).
Maximum Power Point Tracking Using Adaptive Fuzzy Logic control for Photovoltaic System
Anass Ait Laachir
2015-01-01
Full Text Available This work presents an intelligent approach to the improvement and optimization of control performance of a photovoltaic system with maximum power point tracking based on fuzzy logic control. This control was compared with the conventional control based on Perturb &Observe algorithm. The results obtained in Matlab/Simulink under different conditions show a marked improvement in the performance of fuzzy control MPPT of the PV system.
Wenhui Hou
2016-01-01
Full Text Available In order to extract the maximum power from PV system, the maximum power point tracking (MPPT technology has always been applied in PV system. At present, various MPPT control methods have been presented. The perturb and observe (P&O and conductance increment methods are the most popular and widely used under the constant irradiance. However, these methods exhibit fluctuations among the maximum power point (MPP. In addition, the changes of the environmental parameters, such as cloud cover, plant shelter, and the building block, will lead to the radiation change and then have a direct effect on the location of MPP. In this paper, a feasible MPPT method is proposed to adapt to the variation of the irradiance. This work applies the glowworm swarm optimization (GSO algorithm to determine the optimal value of a reference voltage in the PV system. The performance of the proposed GSO algorithm is evaluated by comparing it with the conventional P&O method in terms of tracking speed and accuracy by utilizing MATLAB/SIMULINK. The simulation results demonstrate that the tracking capability of the GSO algorithm is superior to that of the traditional P&O algorithm, particularly under low radiance and sudden mutation irradiance conditions.
Does the Budyko curve reflect a maximum power state of hydrological systems? A backward analysis
Westhoff, Martijn; Zehe, Erwin; Archambeau, Pierre; Dewals, Benjamin
2016-04-01
Almost all catchments plot within a small envelope around the Budyko curve. This apparent behaviour suggests that organizing principles may play a role in the evolution of catchments. In this paper we applied the thermodynamic principle of maximum power as the organizing principle. In a top-down approach we derived mathematical formulations of the relation between relative wetness and gradients driving runoff and evaporation for a simple one-box model. We did this in an inverse manner such that when the conductances are optimized with the maximum power principle, the steady state behaviour of the model leads exactly to a point on the asymptotes of the Budyko curve. Subsequently, we added dynamics in forcing and actual evaporations, causing the Budyko curve to deviate from the asymptotes. Despite the simplicity of the model, catchment observations compare reasonably well with the Budyko curves subject to observed dynamics in rainfall and actual evaporation. Thus by constraining the - with the maximum power principle optimized - model with the asymptotes of the Budyko curve we were able to derive more realistic values of the aridity and evaporation index without any parameter calibration. Future work should focus on better representing the boundary conditions of real catchments and eventually adding more complexity to the model.
Efficiency at maximum power of thermochemical engines with near-independent particles.
Luo, Xiaoguang; Liu, Nian; Qiu, Teng
2016-03-01
Two-reservoir thermochemical engines are established by using near-independent particles (including Maxwell-Boltzmann, Fermi-Dirac, and Bose-Einstein particles) as the working substance. Particle and heat fluxes can be formed based on the temperature and chemical potential gradients between two different reservoirs. A rectangular-type energy filter with width Γ is introduced for each engine to weaken the coupling between the particle and heat fluxes. The efficiency at maximum power of each particle system decreases monotonously from an upper bound η(+) to a lower bound η(-) when Γ increases from 0 to ∞. It is found that the η(+) values for all three systems are bounded by η(C)/2 ≤ η(+) ≤ η(C)/(2-η(C)) due to strong coupling, where η(C) is the Carnot efficiency. For the Bose-Einstein system, it is found that the upper bound is approximated by the Curzon-Ahlborn efficiency: η(CA)=1-sqrt[1-η(C)]. When Γ → ∞, the intrinsic maximum powers are proportional to the square of the temperature difference of the two reservoirs for all three systems, and the corresponding lower bounds of efficiency at maximum power can be simplified in the same form of η(-)=η(C)/[1+a(0)(2-η(C))].
Efficiency at maximum power of thermochemical engines with near-independent particles
Luo, Xiaoguang; Liu, Nian; Qiu, Teng
2016-03-01
Two-reservoir thermochemical engines are established by using near-independent particles (including Maxwell-Boltzmann, Fermi-Dirac, and Bose-Einstein particles) as the working substance. Particle and heat fluxes can be formed based on the temperature and chemical potential gradients between two different reservoirs. A rectangular-type energy filter with width Γ is introduced for each engine to weaken the coupling between the particle and heat fluxes. The efficiency at maximum power of each particle system decreases monotonously from an upper bound η+ to a lower bound η- when Γ increases from 0 to ∞ . It is found that the η+ values for all three systems are bounded by ηC/2 ≤η+≤ηC/(2 -ηC ) due to strong coupling, where ηC is the Carnot efficiency. For the Bose-Einstein system, it is found that the upper bound is approximated by the Curzon-Ahlborn efficiency: ηCA=1 -√{1 -ηC } . When Γ →∞ , the intrinsic maximum powers are proportional to the square of the temperature difference of the two reservoirs for all three systems, and the corresponding lower bounds of efficiency at maximum power can be simplified in the same form of η-=ηC/[1 +a0(2 -ηC ) ] .
Impact of Load Behavior on Transient Stability and Power Transfer Limitations
Gordon, Mark
2009-01-01
This paper presents utility based load modeling practices and explores the interaction between loads and the power system and the effect of the interaction on transient stability and power transfer limitations. The effect of load composition is investigated at major load centers together with the......This paper presents utility based load modeling practices and explores the interaction between loads and the power system and the effect of the interaction on transient stability and power transfer limitations. The effect of load composition is investigated at major load centers together...
Real power regulation for the utility power grid via responsive loads
McIntyre, Timothy J [Knoxville, TN; Kirby, Brendan J [Knoxville, TN; Kisner, Roger A
2009-05-19
A system for dynamically managing an electrical power system that determines measures of performance and control criteria for the electric power system, collects at least one automatic generation control (AGC) input parameter to at least one AGC module and at least one automatic load control (ALC) input parameter to at least one ALC module, calculates AGC control signals and loads as resources (LAR) control signals in response to said measures of performance and control criteria, propagates AGC control signals to power generating units in response to control logic in AGC modules, and propagates LAR control signals to at least one LAR in response to control logic in ALC modules.
Glycol-Substitute for High Power RF Water Loads
Ebert, Michael
2005-01-01
In water loads for high power rf applications, power is dissipated directly into the coolant. Loads for frequencies below approx. 1GHz are ordinarily using an ethylene glycol-water mixture as coolant. The rf systems at DESY utilize about 100 glycol water loads with powers ranging up to 600kW. Due to the increased ecological awareness, the use of glycol is now considered to be problematic. In EU it is forbidden to discharge glycol into the waste water system. In case of cooling system leakages one has to make sure that no glycol is lost. Since it is nearly impossible to avoid any glycol loss in large rf systems, a glycol-substitute was searched for and found. The found sodium-molybdate based substitute is actually a additive for corrosion protection in water systems. Sodium-molybdate is ecologically harmless; for instance, it is also used as fertilizer in agriculture. A homoeopathic dose of 0.4% mixed into deionised water gives better rf absorption characteristics than a 30% glycol mixture. The rf coolant feat...
Remote Area Power Supply (RAPS) load and resource profiles.
Giles, Lauren (Energetics, Inc., Washington, DC); Skolnik, Edward G. (Energetics, Inc., Washington, DC); Marchionini, Brian (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)
2007-07-01
In 1997, an international team interested in the development of Remote Area Power Supply (RAPS) systems for rural electrification projects around the world was organized by the International Lead Zinc Research Organization (ILZRO) with the support of Sandia National Laboratories (SNL). The team focused on defining load and resource profiles for RAPS systems. They identified single family homes, small communities, and villages as candidates for RAPS applications, and defined several different size/power requirements for each. Based on renewable energy and resource data, the team devised a ''strawman'' series of load profiles. A RAPS system typically consists of a renewable and/or conventional generator, power conversion equipment, and a battery. The purpose of this report is to present data and information on insolation levels and load requirements for ''typical'' homes, small communities, and larger villages around the world in order to facilitate the development of robust design practices for RAPS systems, and especially for the storage battery component. These systems could have significant impact on areas of the world that would otherwise not be served by conventional electrical grids.
Li, Yonghui; Wu, Qiuwei; Zhu, Haiyu
2015-01-01
Based on the benchmark solid oxide fuel cell (SOFC) dynamic model for power system studies and the analysis of the SOFC operating conditions, the nonlinear programming (NLP) optimization method was used to determine the maximum electrical efficiency of the grid-connected SOFC subject...
Nagayoshi, Hiroshi; Nakabayashi, Tatsuya; Maiwa, Hiroshi; Kajikawa, Takenobu
2011-05-01
This paper describes a practical high-efficiency thermoelectric (TE) power conditioner with maximum power point tracking (MPPT) control for thermoelectric generators and the operation results for a battery load system. This power conditioner comprises a high-frequency step-up/step-down switching converter and a microcontroller; a synchronized switching circuit is introduced to achieve high conversion efficiency. Furthermore, it is equipped with a battery charge control program and has a maximum conversion efficiency of 96.7%. An impedance matching method developed for MPPT control showed excellent response against a change in the TEG output, making it suitable for solar TEGs as well as general applications.
Maximum Output Power Control System of Variable-Speed Small Wind Generators
Amano, Yoko; Kajiwara, Hiroyuki
This paper proposes a maximum output power control system of variable-speed small wind generators. Paying attention to an optimum rotational speed of a single phase AC wind generator which can obtain maximum output power according to natural wind speed, the proposed method adjusts the rotational speed of the single phase AC generator to the optimum rotational speed. Since this adjustment is realized on line so that it can be adapted for variable-speed wind, a generated power brake links directly with the single phase AC generator, and the rotational speed of the single phase AC generator is adjusted by controlling the current that flows the FET (Field-Effect Transistor) device as the generated power brake. In order to reduce heat loss of the FET device, the PWM (Pulse Width Modulation) controller is introduced. Moreover, the experimental system of the proposed method is constituted and the experiment is performed. Finally, the validity and the practicality of the proposed method are confirmed by experimental results.
Nadhir, Ahmad; Naba, Agus; Hiyama, Takashi
An optimal control for maximizing extraction of power in variable-speed wind energy conversion system is presented. Intelligent gradient detection by fuzzy inference system (FIS) in maximum power point tracking control is proposed to achieve power curve operating near optimal point. Speed rotor reference can be adjusted by maximum power point tracking fuzzy controller (MPPTFC) such that the turbine operates around maximum power. Power curve model can be modelled by using adaptive neuro fuzzy inference system (ANFIS). It is required to simply well estimate just a few number of maximum power points corresponding to optimum generator rotor speed under varying wind speed, implying its training can be done with less effort. Using the trained fuzzy model, some estimated maximum power points as well as their corresponding generator rotor speed and wind speed are determined, from which a linear wind speed feedback controller (LWSFC) capable of producing optimum generator speed can be obtained. Applied to a squirrel-cage induction generator based wind energy conversion system, MPPTFC and LWSFC could maximize extraction of the wind energy, verified by a power coefficient stay at its maximum almost all the time and an actual power line close to a maximum power efficiency line reference.
Potential for solar-powered base-load capacity
Stoll, Brady; Deinert, Mark
2013-04-01
In 2010 nuclear power accounted for 27% of electricity production in Japan. The March 2011 disaster at the Fukushima Daiichi power station resulted in the closure of all of Japans nuclear power plants and it remains an open question as to how many will reopen. Even before the loss of nuclear capacity there were efforts in Japan to foster the use of renewable energy, including large-scale solar power. Nuclear power plants in Japan operated beyond base load with excess energy being stored in large scale pumped hydroelectric storage systems. Here we show how coupling these storage systems to rooftop solar systems in Tokyo could compensate for the loss of nuclear power. Data from a study of rooftop space, and a 34-year data set of average daily irradiance in the Tokyo metropolitan area were used. If current generation PV systems were placed on the available rooftop space in greater Tokyo, this coupled system could provide for 20% of Toyo's nuclear capacity with a capacity factor of 0.99. Using pumped hydroelectric storage with six times this rooftop area could completely provide for TEPCO's nuclear capacity with a capacity factor of 0.98.
Wang, Heming; Park, Jae-Do; Ren, Zhiyong
2012-05-01
Microbial fuel cell (MFC) technology offers a sustainable approach to harvest electricity from biodegradable materials. Energy production from MFCs has been demonstrated using external resistors or charge pumps, but such methods can only dissipate energy through heat or receive electrons passively from the MFC without any controllability. This study developed a new approach and system that can actively extract energy from MFC reactors at any operating point without using any resistors, especially at the peak power point to maximize energy production. Results show that power harvesting from a recirculating-flow MFC can be well maintained by the maximum power point circuit (MPPC) at its peak power point, while a charge pump was not able to change operating point due to current limitation. Within 18-h test, the energy gained from the MPPC was 76.8 J, 76 times higher than the charge pump (1.0 J) that was commonly used in MFC studies. Both conditions resulted in similar organic removal, but the Coulombic efficiency obtained from the MPPC was 21 times higher than that of the charge pump. Different numbers of capacitors could be used in the MPPC for various energy storage requirements and power supply, and the energy conversion efficiency of the MPPC was further characterized to identify key factors for system improvement. This active energy harvesting approach provides a new perspective for energy harvesting that can maximize MFC energy generation and system controllability.
Matching of Silicon Thin-Film Tandem Solar Cells for Maximum Power Output
C. Ulbrich
2013-01-01
Full Text Available We present a meaningful characterization method for tandem solar cells. The experimental method allows for optimizing the output power instead of the current. Furthermore, it enables the extraction of the approximate AM1.5g efficiency when working with noncalibrated spectra. Current matching of tandem solar cells under short-circuit condition maximizes the output current but is disadvantageous for the overall fill factor and as a consequence does not imply an optimization of the output power of the device. We apply the matching condition to the maximum power output; that is, a stack of solar cells is power matched if the power output of each subcell is maximal at equal subcell currents. The new measurement procedure uses additional light-emitting diodes as bias light in the JV characterization of tandem solar cells. Using a characterized reference tandem solar cell, such as a hydrogenated amorphous/microcrystalline silicon tandem, it is possible to extract the AM1.5g efficiency from tandems of the same technology also under noncalibrated spectra.
Measurement of in-bore side loads and comparison to first maximum yaw
Donald E. Carlucci
2016-04-01
Full Text Available In-bore yaw of a projectile in a gun tube has been shown to result in range loss if the yaw is significant. An attempt was made to determine if relationships between in-bore yaw and projectile First Maximum Yaw (FMY were observable. Experiments were conducted in which pressure transducers were mounted near the muzzle of a 155 mm cannon in three sets of four. Each set formed a cruciform pattern to obtain a differential pressure across the projectile. These data were then integrated to form a picture of what the overall pressure distribution was along the side of the projectile. The pressure distribution was used to determine a magnitude and direction of the overturning moment acting on the projectile. This moment and its resulting angular acceleration were then compared to the actual first maximum yaw observed in the test. The degree of correlation was examined using various statistical techniques. Overall uncertainty in the projectile dynamics was between 20% and 40% of the mean values of FMY.
Measurement of in-bore side loads and comparison to first maximum yaw
Donald E. CARLUCCI; Ryan DECKER; Julio VEGA; Douglas RAY
2016-01-01
In-bore yaw of a projectile in a gun tube has been shown to result in range loss if the yaw is significant. An attempt was made to determine if relationships between in-bore yaw and projectile First Maximum Yaw (FMY) were observable. Experiments were conducted in which pressure transducers were mounted near the muzzle of a 155 mm cannon in three sets of four. Each set formed a cruciform pattern to obtain a differential pressure across the projectile. These data were then integrated to form a picture of what the overall pressure distribution was along the side of the projectile. The pressure distribution was used to determine a magnitude and direction of the overturning moment acting on the projectile. This moment and its resulting angular acceleration were then compared to the actual first maximum yaw observed in the test. The degree of correlation was examined using various statistical techniques. Overall uncertainty in the projectile dynamics was between 20%and 40%of the mean values of FMY.
Overview of Maximum Power Point Tracking Techniques for Photovoltaic Energy Production Systems
2017-01-01
A substantial growth of the installed photovoltaic (PV) systems capacity has occurred around the world during the last decade, thus enhancing the availability of electric energy in an environmentally friendly way. The maximum power point tracking (MPPT) technique enables to maximize the energy...... production of PV sources, despite the stochastically varying solar irradiation and ambient temperature conditions. Thereby, the overall efficiency of the PV energy production system is increased. Numerous techniques have been presented during the last decades for implementing the MPPT process in a PV system...
Efficiency and its bounds for thermal engines at maximum power using Newton's law of cooling
Yan, H; Guo, H.
2012-01-01
We study a thermal engine model for which Newton's cooling law is obeyed during heat transfer processes. The thermal efficiency and its bounds at maximum output power are derived and discussed. This model, though quite simple, can be applied not only to Carnot engines but also to four other types of engines. For the long thermal contact time limit, new bounds, tighter than what were known before, are obtained. In this case, this model can simulate Otto, Joule-Brayton, Diesel, and Atkinson eng...
Wang, Jianhui; He, Jizhou
2012-11-01
We investigate the efficiency at the maximum power output (EMP) of an irreversible Carnot engine performing finite-time cycles between two reservoirs at constant temperatures T(h) and T(c) (Carnot efficiency, whether the internally dissipative friction is considered or not. When dissipations of two "isothermal" and two "adiabatic" processes are symmetric, respectively, and the time allocation between the adiabats and the contact time with the reservoir satisfy a certain relation, the Curzon-Ahlborn (CA) efficiency η(CA) = 1-sqrt[T(c)/T(h)] is derived.
Larbes, C.; Ait Cheikh, S.M.; Obeidi, T.; Zerguerras, A. [Laboratoire des Dispositifs de Communication et de Conversion Photovoltaique, Departement d' Electronique, Ecole Nationale Polytechnique, 10, Avenue Hassen Badi, El Harrach, Alger 16200 (Algeria)
2009-10-15
This paper presents an intelligent control method for the maximum power point tracking (MPPT) of a photovoltaic system under variable temperature and irradiance conditions. First, for the purpose of comparison and because of its proven and good performances, the perturbation and observation (P and O) technique is briefly introduced. A fuzzy logic controller based MPPT (FLC) is then proposed which has shown better performances compared to the P and O MPPT based approach. The proposed FLC has been also improved using genetic algorithms (GA) for optimisation. Different development stages are presented and the optimized fuzzy logic MPPT controller (OFLC) is then simulated and evaluated, which has shown better performances. (author)
Atik, L.; Petit, P.; Sawicki, J. P.; Ternifi, Z. T.; Bachir, G.; Della, M.; Aillerie, M.
2017-02-01
Solar panels have a nonlinear voltage-current characteristic, with a distinct maximum power point (MPP), which depends on the environmental factors, such as temperature and irradiation. In order to continuously harvest maximum power from the solar panels, they have to operate at their MPP despite the inevitable changes in the environment. Various methods for maximum power point tracking (MPPT) were developed and finally implemented in solar power electronic controllers to increase the efficiency in the electricity production originate from renewables. In this paper we compare using Matlab tools Simulink, two different MPP tracking methods, which are, fuzzy logic control (FL) and sliding mode control (SMC), considering their efficiency in solar energy production.
Wei Wang
2012-05-01
Full Text Available This paper proposes a novel optimal current given (OCG maximum power point tracking (MPPT control strategy based on the theory of power feedback and hill climb searching (HCS for a permanent magnet direct drive wind energy conversion system (WECS. The presented strategy not only has the advantages of not needing the wind speed and wind turbine characteristics of the traditional HCS method, but it also improves the stability and accuracy of MPPT by estimating the exact loss torque. The OCG MPPT control strategy is first carried out by simulation, then an experimental platform based on the dSPACE1103 controller is built and a 5.5 kW permanent magnet synchronous generator (PMSG is tested. Furthermore, the proposed method is compared experimentally with the traditional optimum tip speed ratio (TSR MPPT control. The experiments verify the effectiveness of the proposed OCG MPPT strategy and demonstrate its better performance than the traditional TSR MPPT control.
Dithering Digital Ripple Correlation Control for Photovoltaic Maximum Power Point Tracking
Barth, C; Pilawa-Podgurski, RCN
2015-08-01
This study demonstrates a new method for rapid and precise maximum power point tracking in photovoltaic (PV) applications using dithered PWM control. Constraints imposed by efficiency, cost, and component size limit the available PWM resolution of a power converter, and may in turn limit the MPP tracking efficiency of the PV system. In these scenarios, PWM dithering can be used to improve average PWM resolution. In this study, we present a control technique that uses ripple correlation control (RCC) on the dithering ripple, thereby achieving simultaneous fast tracking speed and high tracking accuracy. Moreover, the proposed method solves some of the practical challenges that have to date limited the effectiveness of RCC in solar PV applications. We present a theoretical derivation of the principles behind dithering digital ripple correlation control, as well as experimental results that show excellent tracking speed and accuracy with basic hardware requirements.
Wu, Feilong; He, Jizhou; Ma, Yongli; Wang, Jianhui
2014-12-01
We consider the efficiency at maximum power of a quantum Otto engine, which uses a spin or a harmonic system as its working substance and works between two heat reservoirs at constant temperatures T(h) and T(c) (power based on these two different kinds of quantum systems are bounded from the upper side by the same expression η(mp)≤η(+)≡η(C)(2)/[η(C)-(1-η(C))ln(1-η(C))] with η(C)=1-T(c)/T(h) as the Carnot efficiency. This expression η(mp) possesses the same universality of the CA efficiency η(CA)=1-√(1-η(C)) at small relative temperature difference. Within the context of irreversible thermodynamics, we calculate the Onsager coefficients and show that the value of η(CA) is indeed the upper bound of EMP for an Otto engine working in the linear-response regime.
Chao Peng; Zhenzhen Zhang; Jia Wu
2015-01-01
A frequency control approach based on wind power and load power prediction information is proposed for wind-diesel-battery hybrid power system (WDBHPS). To maintain the frequency stability by wind power and diesel generation as much as possible, a fuzzy control theory based wind and diesel power control module is designed according to wind power and load prediction information. To compensate frequency fluctuation in real time and enhance system disturbance rejection ability, a battery energy ...
Elhussain, O. A.; Abdel-Magid, T. I. M.
2016-08-01
Mono-Crystalline solar cell module is experimentally conducted in Khartoum, Sudan to study the difference between maximum empirical value of peak Watt and maximum value of thermal power produced in field under highly sufficient solar conditions. Field measurements are recorded for incident solar radiation, produced voltage, current and temperature at several time intervals during sun shine period. The thermal power system has been calculated using fundamental principles of heat transfer. The study shows that solar power for considered module could not attain the empirical peak power irrespective to maximum value of direct incident solar radiation and maximum temperature gained. A loss of about 6% of power can be considered as the difference between field measurements and the manufacturer's indicated empirical value. Solar cell exhibits 94% efficiency in comparison with manufacturer's provided data, and is 3'% more efficient in thermal energy production than in electrical power extraction for hot-dry climate conditions.
Shortening start-up and an extension of the power unit load range
Taler Jan
2017-01-01
Full Text Available A power plant with additional water pressure tanks was proposed. The maximum rise in the block electric power resulting from the shut-off of low-pressure regenerative heaters was determined. At that time, the boiler is fed with hot water from water pressure tanks acting as heat accumulators. Accumulation of hot water in water tanks is also proposed in the periods of the power unit small load. In order to lower the plant electric power in the off-peak night hours, water heated to the nominal temperature in low-pressure regenerative heaters is directed from the feed water tank to pressure tanks. The water accumulated during the night is used to feed the boiler during the period of peak demand for electricity. Pressure accumulators are proposed to be used for the rapid start-up of the boiler from a cold state. The evaporator of the boiler is filled at the beginning of start-up with hot water from the accumulators. Drops in the power block electric power were determined for different capacities of the tanks and periods when they are charged. The tanks may also be used to ensure a sudden increase in the electric power of the unit that is operating in the automatic system of frequency and power control (in Polish: ARCM.
Apertet, Y; Ouerdane, H; Goupil, C; Lecoeur, Ph
2012-03-01
Energy conversion efficiency at maximum output power, which embodies the essential characteristics of heat engines, is the main focus of the present work. The so-called Curzon and Ahlborn efficiency η(CA) is commonly believed to be an absolute reference for real heat engines; however, a different but general expression for the case of stochastic heat engines, η(SS), was recently found and then extended to low-dissipation engines. The discrepancy between η(CA) and η(SS) is here analyzed considering different irreversibility sources of heat engines, of both internal and external types. To this end, we choose a thermoelectric generator operating in the strong-coupling regime as a physical system to qualitatively and quantitatively study the impact of the nature of irreversibility on the efficiency at maximum output power. In the limit of pure external dissipation, we obtain η(CA), while η(SS) corresponds to the case of pure internal dissipation. A continuous transition between from one extreme to the other, which may be operated by tuning the different sources of irreversibility, also is evidenced.
Validity of different prediction equations of the maximum load in mixed martial arts athletes
Jairo Laécio Guerra Filho
2014-12-01
Full Text Available The purpose of this study was to investigate the validity of different prediction equations to the one maximum repetition (1-RM test at the bench press exercise (BP with bar in mixed martial arts (MMA athletes. The sample was composed by 19 male MMA athletes (27.68 ± 6.19 years. The data collection was performed in two different moments: 1 in 1-RM test; 2 in submaximal test and their respective numbers of repetitions. The paired-sample t test was performed and was noted that, among the six equations compared with the 1-RM test, only the Adams (p= 0.337 and O’Conner’s (p= 0.250 equations showed no significant differences. However, there were high Pearson correlation and intraclass correlation coefficients (r= 0.924, ICC= 0.924; r= 0.944, ICC= 0.944, respectively. Nevertheless, all equations showed high correlations that ranged between 0.854 and 0.944. In conclusion, for estimation of 1-RM, the predictive equations based on Adams and O'Conner’s are valid in MMA athletes.
A high-power switch-mode dc power supply for dynamic loads
Shimer, D.W.; Lange, A.C. [Lawrence Livermore National Lab., CA (United States); Bombay, J.N. [Kaiser Engineers, Oakland, CA (United States)
1994-06-23
High-voltage dc power supplies are often required to operate with highly dynamic loads, such as arcs. A switch-mode dc power supply can offer significant advantages over conventional thyristor-based dc power supplies under such conditions. It can quickly turn off the supply to extinguish the arc, and it can quickly recover after the arc. It has a relatively small output filter capacitance, which results in small stored energy available to the arc. A 400-kW, 50-kV switch-mode dc power supply for an electron-beam gun that exploits these advantages was designed and tested. It uses four 100-kW, current-source-type dc-dc converters with inputs in parallel and outputs in series. The dc-dc converters operate at 20 kHz in the voltage regulator part and 10 kHz in the inverter, transformer, and output rectifier part of the circuit. Insulated gate bipolar transistors (IGBTs) are used as the power switches. Special techniques are used to protect the power supply and load against arcs and hard shorts. The power supply has an efficiency of 93%, an output voltage ripple of 1%, and fast dynamic response. In addition, it is nearly one-third the size of conventional power supplies.
Monitoring Wind Turbine Loading Using Power Converter Signals
Rieg, C. A.; Smith, C. J.; Crabtree, C. J.
2016-09-01
The ability to detect faults and predict loads on a wind turbine drivetrain's mechanical components cost-effectively is critical to making the cost of wind energy competitive. In order to investigate whether this is possible using the readily available power converter current signals, an existing permanent magnet synchronous generator based wind energy conversion system computer model was modified to include a grid-side converter (GSC) for an improved converter model and a gearbox. The GSC maintains a constant DC link voltage via vector control. The gearbox was modelled as a 3-mass model to allow faults to be included. Gusts and gearbox faults were introduced to investigate the ability of the machine side converter (MSC) current (I q) to detect and quantify loads on the mechanical components. In this model, gearbox faults were not detectable in the I q signal due to shaft stiffness and damping interaction. However, a model that predicts the load change on mechanical wind turbine components using I q was developed and verified using synthetic and real wind data.
Radziukynas V.
2016-04-01
Full Text Available The paper analyses the performance results of the recently developed short-term forecasting suit for the Latvian power system. The system load and wind power are forecasted using ANN and ARIMA models, respectively, and the forecasting accuracy is evaluated in terms of errors, mean absolute errors and mean absolute percentage errors. The investigation of influence of additional input variables on load forecasting errors is performed. The interplay of hourly loads and wind power forecasting errors is also evaluated for the Latvian power system with historical loads (the year 2011 and planned wind power capacities (the year 2023.
Ahmadian, Radin
2010-09-01
This study investigated the relationship of anthocyanin concentration from different organic fruit species and output voltage and current in a TiO2 dye-sensitized solar cell (DSSC) and hypothesized that fruits with greater anthocyanin concentration produce higher maximum power point (MPP) which would lead to higher current and voltage. Anthocyanin dye solution was made with crushing of a group of fresh fruits with different anthocyanin content in 2 mL of de-ionized water and filtration. Using these test fruit dyes, multiple DSSCs were assembled such that light enters through the TiO2 side of the cell. The full current-voltage (I-V) co-variations were measured using a 500 Ω potentiometer as a variable load. Point-by point current and voltage data pairs were measured at various incremental resistance values. The maximum power point (MPP) generated by the solar cell was defined as a dependent variable and the anthocyanin concentration in the fruit used in the DSSC as the independent variable. A regression model was used to investigate the linear relationship between study variables. Regression analysis showed a significant linear relationship between MPP and anthocyanin concentration with a p-value of 0.007. Fruits like blueberry and black raspberry with the highest anthocyanin content generated higher MPP. In a DSSC, a linear model may predict MPP based on the anthocyanin concentration. This model is the first step to find organic anthocyanin sources in the nature with the highest dye concentration to generate energy.
Kim, Sang M; Brannan, Kevin M; Zeckoski, Rebecca W; Benham, Brian L
2014-01-01
The objective of this study was to develop bacteria total maximum daily loads (TMDLs) for the Hardware River watershed in the Commonwealth of Virginia, USA. The TMDL program is an integrated watershed management approach required by the Clean Water Act. The TMDLs were developed to meet Virginia's water quality standard for bacteria at the time, which stated that the calendar-month geometric mean concentration of Escherichia coli should not exceed 126 cfu/100 mL, and that no single sample should exceed a concentration of 235 cfu/100 mL. The bacteria impairment TMDLs were developed using the Hydrological Simulation Program-FORTRAN (HSPF). The hydrology and water quality components of HSPF were calibrated and validated using data from the Hardware River watershed to ensure that the model adequately simulated runoff and bacteria concentrations. The calibrated and validated HSPF model was used to estimate the contributions from the various bacteria sources in the Hardware River watershed to the in-stream concentration. Bacteria loads were estimated through an extensive source characterization process. Simulation results for existing conditions indicated that the majority of the bacteria came from livestock and wildlife direct deposits and pervious lands. Different source reduction scenarios were evaluated to identify scenarios that meet both the geometric mean and single sample maximum E. coli criteria with zero violations. The resulting scenarios required extreme and impractical reductions from livestock and wildlife sources. Results from studies similar to this across Virginia partially contributed to a reconsideration of the standard's applicability to TMDL development.
Beltran, H.; Perez, E.; Chen, Zhe
2009-01-01
This paper describes a Fixed Maximum Power Point analog control used in a step-down Pulse Width Modulated power converter. The DC/DC converter drives a DC motor used in small water pumping installations, without any electric storage device. The power supply is provided by PV panels working around...
M. A. García-Sánchez
2016-07-01
Full Text Available Chlorophyll is a pyrrolic pigment with important optical properties, which is the reason it has been studied for many years. Recently, interest has been rising with respect to this molecule because of its outstanding physicochemical properties, particularly applicable to the design and development of luminescent materials, hybrid sensor systems, and photodynamic therapy devices for the treatment of cancer cells and bacteria. More recently, our research group has been finding evidence for the possibility of preserving these important properties of substrates containing chlorophyll covalently incorporated within solid pore matrices, such as SiO2, TiO2 or ZrO2 synthesized through the sol-gel process. In this work, we study the optical properties of silica xerogels organo-modified on their surface with allyl and phenyl groups and containing different concentrations of chlorophyll bonded to the pore walls, in order to optimize the fluorescence that these macrocyclic species displays in solution. The intention of this investigation was to determine the maximum chlorophyll a concentration at which this molecule can be trapped inside the pores of a given xerogel and to ascertain if this pigment remains trapped as a monomer, a dimer, or aggregate. Allyl and phenyl groups were deposited on the surface of xerogels in view of their important effects on the stability of the molecule, as well as over the fluorescence emission of chlorophyll; however, these organic groups allow the trapping of either chlorophyll a monomers or dimers. The determination of the above parameters allows finding the most adequate systems for subsequent in vitro or in vivo studies. The characterization of the obtained xerogels was performed through spectroscopic absorption, emission and excitation spectra. These hybrid systems can be employed as mimics of natural systems; the entrapment of chlorophyll inside pore matrices indicates that it is possible to exploit some of the most
Ouerdane, H.; Apertet, Y.; Goupil, C.; Lecoeur, Ph.
2015-07-01
Classical equilibrium thermodynamics is a theory of principles, which was built from empirical knowledge and debates on the nature and the use of heat as a means to produce motive power. By the beginning of the 20th century, the principles of thermodynamics were summarized into the so-called four laws, which were, as it turns out, definitive negative answers to the doomed quests for perpetual motion machines. As a matter of fact, one result of Sadi Carnot's work was precisely that the heat-to-work conversion process is fundamentally limited; as such, it is considered as a first version of the second law of thermodynamics. Although it was derived from Carnot's unrealistic model, the upper bound on the thermodynamic conversion efficiency, known as the Carnot efficiency, became a paradigm as the next target after the failure of the perpetual motion ideal. In the 1950's, Jacques Yvon published a conference paper containing the necessary ingredients for a new class of models, and even a formula, not so different from that of Carnot's efficiency, which later would become the new efficiency reference. Yvon's first analysis of a model of engine producing power, connected to heat source and sink through heat exchangers, went fairly unnoticed for twenty years, until Frank Curzon and Boye Ahlborn published their pedagogical paper about the effect of finite heat transfer on output power limitation and their derivation of the efficiency at maximum power, now mostly known as the Curzon-Ahlborn (CA) efficiency. The notion of finite rate explicitly introduced time in thermodynamics, and its significance cannot be overlooked as shown by the wealth of works devoted to what is now known as finite-time thermodynamics since the end of the 1970's. The favorable comparison of the CA efficiency to actual values led many to consider it as a universal upper bound for real heat engines, but things are not so straightforward that a simple formula may account for a variety of situations. The
Efficient Photovoltaic System Maximum Power Point Tracking Using a New Technique
Mehdi Seyedmahmoudian
2016-03-01
Full Text Available Partial shading is an unavoidable condition which significantly reduces the efficiency and stability of a photovoltaic (PV system. When partial shading occurs the system has multiple-peak output power characteristics. In order to track the global maximum power point (GMPP within an appropriate period a reliable technique is required. Conventional techniques such as hill climbing and perturbation and observation (P&O are inadequate in tracking the GMPP subject to this condition resulting in a dramatic reduction in the efficiency of the PV system. Recent artificial intelligence methods have been proposed, however they have a higher computational cost, slower processing time and increased oscillations which results in further instability at the output of the PV system. This paper proposes a fast and efficient technique based on Radial Movement Optimization (RMO for detecting the GMPP under partial shading conditions. The paper begins with a brief description of the behavior of PV systems under partial shading conditions followed by the introduction of the new RMO-based technique for GMPP tracking. Finally, results are presented to demonstration the performance of the proposed technique under different partial shading conditions. The results are compared with those of the PSO method, one of the most widely used methods in the literature. Four factors, namely convergence speed, efficiency (power loss reduction, stability (oscillation reduction and computational cost, are considered in the comparison with the PSO technique.
Xiang Luo
2016-07-01
Full Text Available Recently, Vernier permanent magnet (VPM machines, one special case of magnetic flux-modulated (MFM machines, benefiting from their compact, simple construction and low-speed/ high-torque characteristics, have been receiving increasing interest. In this paper, the Vernier structure is integrated with an axial-flux PM machine to obtain the magnetic gear effect and produce an improved torque density for direct-drive wind power generation application. Another advantage of the proposed machine is that the stator flux rotating speed can be relatively high when the shaft speed is low. With this benefit, sensorless control strategy can be easily implemented in a wide speed range. In this paper, an improved sliding mode observer (SMO is proposed to estimate the rotor position and the speed of the proposed machine. With the estimated shaft speeds, the maximum power point tracking (MPPT control strategy is applied to maximize the wind power extraction. The machine design and the sensorless MPPT control strategy are verified by finite element analysis and experimental verification.
Muhammad Riazul Hamid
2016-06-01
Full Text Available This paper describes how to implement MPPT using the most popular switching power supply topology. There are many published works on this topic, but only a tiny portion of them show how to actually implement the algorithms in hardware, as well as state common problems and pitfalls. In our work to keep the design simple we have used Arduino Nano. It has features like: LCD display, Led Indication and it is equipped with various protections to protect the circuitry from abnormal condition. This design is suitable for a 50W solar panel to charge a commonly used 12V lead acid battery. As the maximum power point (MPP of photovoltaic (PV power generation systems changes with changing atmospheric conditions (e.g. solar radiation and temperature, an important consideration in the design of efficient PV systems is to track the MPP correctly. We have implemented the most common MPPT algorithm named Perturb and Observe (PO to control the output of a synchronous buck-converter
Aminov, R. Z.; Shkret, A. F.; Burdenkova, E. Yu.; Garievskii, M. V.
2011-05-01
The results obtained from studies of efficient ways and methods for organizing the operation of developing nuclear power stations in the base load mode are presented. We also show comparative efficiency of different scenarios for unloading condensing thermal power stations, cogeneration stations, combined-cycle power plants, nuclear power stations, and using off-peak electric energy for electricity-intensive loads: pumped-hydroelectric storage, electric-powered heat supply, and electrolysis of water for producing hydrogen and oxygen.
46 CFR 112.15-10 - Loads on systems without a temporary emergency power source.
2010-10-01
... without a temporary emergency power source. If there is no temporary emergency power source, the loads under § 112.15-1 must be arranged so that they can be energized from the final emergency power source. ... 46 Shipping 4 2010-10-01 2010-10-01 false Loads on systems without a temporary emergency power...
Permissible radionuclide loading for organic ion exchange resins from nuclear power plants
MacKenzie, D.R.; Lin, M.; Barletta, R.E.
1983-10-01
A questionnaire on the use of ion exchange resins in nuclear power plants was sent to all operating reactors in the US. Responses were received from 23 of the 48 utilities approached. Information was sought concerning the amounts of radionuclides held by the resins, and the effects of its radiation on the resins both during operation and after removal from service. Relevant information from the questionnaires is summarized and discussed. Available literature on the effects of ionizing radiation on organic ion exchange resins has been reviewed. On the basis of published data on damage to resins by radiation, the technical rationale is given to support NRC's draft branch technical position on a maximum permissible radionuclide loading. It is considered advisable to formulate the rule in terms of a delivered dose rather than a curie loading. A maximum permissible dose of 10/sup 8/ rad is chosen because, while it is large enough that a measurable amount of damage will be done to the resin, it is small enough that the damage will be negligible at a power plant or disposal site. A test procedure has been written which a generator could use to qualify a specific resin for service at a higher dose than permitted by the general rule.
Different types of maximum power point tracking techniques for renewable energy systems: A survey
Khan, Mohammad Junaid; Shukla, Praveen; Mustafa, Rashid; Chatterji, S.; Mathew, Lini
2016-03-01
Global demand for electricity is increasing while production of energy from fossil fuels is declining and therefore the obvious choice of the clean energy source that is abundant and could provide security for development future is energy from the sun. In this paper, the characteristic of the supply voltage of the photovoltaic generator is nonlinear and exhibits multiple peaks, including many local peaks and a global peak in non-uniform irradiance. To keep global peak, MPPT is the important component of photovoltaic systems. Although many review articles discussed conventional techniques such as P & O, incremental conductance, the correlation ripple control and very few attempts have been made with intelligent MPPT techniques. This document also discusses different algorithms based on fuzzy logic, Ant Colony Optimization, Genetic Algorithm, artificial neural networks, Particle Swarm Optimization Algorithm Firefly, Extremum seeking control method and hybrid methods applied to the monitoring of maximum value of power at point in systems of photovoltaic under changing conditions of irradiance.
Vaudrey, A; Lanzetta, F; Glises, R
2009-01-01
Producing useful electrical work in consuming chemical energy, the fuel cell have to reject heat to its surrounding. However, as it occurs for any other type of engine, this thermal energy cannot be exchanged in an isothermal way in finite time through finite areas. As it was already done for various types of systems, we study the fuel cell within the finite time thermodynamics framework and define an endoreversible fuel cell. Considering different types of heat transfer laws, we obtain an optimal value of the operating temperature, corresponding to a maximum produced power. This analysis is a first step of a thermodynamical approach of design of thermal management devices, taking into account performances of the whole system.
The maximum power efficiency 1-√τ: Research, education, and bibliometric relevance
Calvo Hernández, A.; Roco, J. M. M.; Medina, A.; Velasco, S.; Guzmán-Vargas, L.
2015-07-01
The well-known efficiency at maximum power for a cyclic system working between hot T h and low T c temperatures given by the equation 1-√ τ( τ= T c /T h), has become a landmark result with regards to the thermodynamic optimization of a great variety of energy converters. Its wide applicability and sole dependence on the external heat bath temperatures (as the Carnot efficiency does) allows for an easy comparison with experimental efficiencies leading to a striking fair agreement. Reversible, finite-time, and linear-irreversible derivations are analyzed in order to show a broader perspective about its meaning from both researching and pedagogical point of views. Its scientific relevance and historical development are also analyzed in this work by means of some bibliometric data. This article is supplemented with comments by Hong Qian and a final reply by the authors.
Koofigar, Hamid Reza
2016-01-01
The problem of maximum power point tracking (MPPT) in photovoltaic (PV) systems, despite the model uncertainties and the variations in environmental circumstances, is addressed. Introducing a mathematical description, an adaptive sliding mode control (ASMC) algorithm is first developed. Unlike many previous investigations, the output voltage is not required to be sensed and the upper bound of system uncertainties and the variations of irradiance and temperature are not required to be known. Estimating the output voltage by an update law, an adaptive-based H∞ tracking algorithm is then developed for the case the perturbations are energy-bounded. The stability analysis is presented for the proposed tracking control schemes, based on the Lyapunov stability theorem. From a comparison viewpoint, some numerical and experimental studies are also presented and discussed.
Dhara, Chirag; Kleidon, Axel
2015-01-01
Convective and radiative cooling are the two principle mechanisms by which the Earth's surface transfers heat into the atmosphere and that shape surface temperature. However, this partitioning is not sufficiently constrained by energy and mass balances alone. We use a simple energy balance model in which convective fluxes and surface temperatures are determined with the additional thermodynamic limit of maximum convective power. We then show that the broad geographic variation of heat fluxes and surface temperatures in the climatological mean compare very well with the ERA-Interim reanalysis over land and ocean. We also show that the estimates depend considerably on the formulation of longwave radiative transfer and that a spatially uniform offset is related to the assumed cold temperature sink at which the heat engine operates.
Improved incremental conductance method for maximum power point tracking using cuk converter
M. Saad Saoud
2014-03-01
Full Text Available The Algerian government relies on a strategy focused on the development of inexhaustible resources such as solar and uses to diversify energy sources and prepare the Algeria of tomorrow: about 40% of the production of electricity for domestic consumption will be from renewable sources by 2030, Therefore it is necessary to concentrate our forces in order to reduce the application costs and to increment their performances, Their performance is evaluated and compared through theoretical analysis and digital simulation. This paper presents simulation of improved incremental conductance method for maximum power point tracking (MPPT using DC-DC cuk converter. This improved algorithm is used to track MPPs because it performs precise control under rapidly changing Atmospheric conditions, Matlab/ Simulink were employed for simulation studies.
Efficiency and its bounds for thermal engines at maximum power using Newton's law of cooling.
Yan, H; Guo, Hao
2012-01-01
We study a thermal engine model for which Newton's cooling law is obeyed during heat transfer processes. The thermal efficiency and its bounds at maximum output power are derived and discussed. This model, though quite simple, can be applied not only to Carnot engines but also to four other types of engines. For the long thermal contact time limit, new bounds, tighter than what were known before, are obtained. In this case, this model can simulate Otto, Joule-Brayton, Diesel, and Atkinson engines. While in the short contact time limit, which corresponds to the Carnot cycle, the same efficiency bounds as that from Esposito et al. [Phys. Rev. Lett. 105, 150603 (2010)] are derived. In both cases, the thermal efficiency decreases as the ratio between the heat capacities of the working medium during heating and cooling stages increases. This might provide instructions for designing real engines.
Efficiency and its bounds for thermal engines at maximum power using Newton's law of cooling
Yan, H.; Guo, Hao
2012-01-01
We study a thermal engine model for which Newton's cooling law is obeyed during heat transfer processes. The thermal efficiency and its bounds at maximum output power are derived and discussed. This model, though quite simple, can be applied not only to Carnot engines but also to four other types of engines. For the long thermal contact time limit, new bounds, tighter than what were known before, are obtained. In this case, this model can simulate Otto, Joule-Brayton, Diesel, and Atkinson engines. While in the short contact time limit, which corresponds to the Carnot cycle, the same efficiency bounds as that from Esposito [Phys. Rev. Lett.PRLTAO0031-900710.1103/PhysRevLett.105.150603 105, 150603 (2010)] are derived. In both cases, the thermal efficiency decreases as the ratio between the heat capacities of the working medium during heating and cooling stages increases. This might provide instructions for designing real engines.
Efficiency at maximum power of a quantum heat engine based on two coupled oscillators.
Wang, Jianhui; Ye, Zhuolin; Lai, Yiming; Li, Weisheng; He, Jizhou
2015-06-01
We propose and theoretically investigate a system of two coupled harmonic oscillators as a heat engine. We show how these two coupled oscillators within undamped regime can be controlled to realize an Otto cycle that consists of two adiabatic and two isochoric processes. During the two isochores the harmonic system is embedded in two heat reservoirs at constant temperatures T(h) and T(c)(semigroup approach to model the thermal relaxation dynamics along the two isochoric processes, and we find the upper bound of efficiency at maximum power (EMP) η* to be a function of the Carnot efficiency η(C)(=1-T(c)/T(h)): η*≤η(+)≡η(C)(2)/[η(C)-(1-η(C))ln(1-η(C))], identical to those previously derived from ideal (noninteracting) microscopic, mesoscopic, and macroscopic systems.
Abhishek Khanna
2012-01-01
Full Text Available We revisit the problem of optimal power extraction in four-step cycles (two adiabatic and two heat-transfer branches when the finite-rate heat transfer obeys a linear law and the heat reservoirs have finite heat capacities. The heat-transfer branch follows a polytropic process in which the heat capacity of the working fluid stays constant. For the case of ideal gas as working fluid and a given switching time, it is shown that maximum work is obtained at Curzon-Ahlborn efficiency. Our expressions clearly show the dependence on the relative magnitudes of heat capacities of the fluid and the reservoirs. Many previous formulae, including infinite reservoirs, infinite-time cycles, and Carnot-like and non-Carnot-like cycles, are recovered as special cases of our model.
Wijesekara, Waruna; Rosendahl, Lasse; Wu, NingYu;
Oxide thermoelectric materials are promising candidates for energy harvesting from mid to high temperature heat sources. In this work, the oxide thermoelectric materials and the final design of the high temperature thermoelectric module were developed. Also, prototypes of oxide thermoelectric...... generator were built for high temperature applications. This paper specifically discusses the thermoelectric module design and the prototype validations of the design. Here p type calcium cobalt oxide and n type aluminum doped ZnO were developed as the oxide thermoelectric materials. Hot side and cold side...... temperatures were used as 1100 K and 400 K respectively. Using analytical methods, the optimum thermoelement length and the thermoelements area ratio were explored in order to provide the maximum power output by the uni-couple and it is compared to methods reported in literature. Based on operating conditions...
Howell, L W
2002-01-01
The method of Maximum Likelihood (ML) is used to estimate the spectral parameters of an assumed broken power law energy spectrum from simulated detector responses. This methodology, which requires the complete specificity of all cosmic-ray detector design parameters, is shown to provide approximately unbiased, minimum variance, and normally distributed spectra information for events detected by an instrument having a wide range of commonly used detector response functions. The ML procedure, coupled with the simulated performance of a proposed space-based detector and its planned life cycle, has proved to be of significant value in the design phase of a new science instrument. The procedure helped make important trade studies in design parameters as a function of the science objectives, which is particularly important for space-based detectors where physical parameters, such as dimension and weight, impose rigorous practical limits to the design envelope. This ML methodology is then generalized to estimate bro...
Maximum power point tracking of a photovoltaic energy system using neural fuzzy techniques
LI Chun-hua; ZHU Xin-jian; SUI Sheng; HU Wan-qi
2009-01-01
In order to improve the output efficiency of a photovoltaic (PV) energy system, the real-time maximum power point (MPP) of the PV array should be tracked closely. The non-linear and time-variant characteristics of the photovoltaic array and the non-linear and non-minimum phase characteristics of a boost converter make it difficult to track the MPP as in traditional control strategies. A neural fuzzy controller (NFC) in conjunction with the reasoning capability of fuzzy logical systems and the learning capability of neural networks is proposed to track the MPP in this paper. A gradient estimator based on a radial basis function neural network is developed to provide the reference information to the NFC. With a derived learning algorithm, the parameters of the NFC are updated adaptively. Experimental results show that, compared with the fuzzy logic control algorithm, the proposed control algorithm provides much better tracking performance.
Man, E. A.; Sera, D.; Mathe, L.; Schaltz, E.; Rosendahl, L.
2016-03-01
Characterization of thermoelectric generators (TEG) is widely discussed and equipment has been built that can perform such analysis. One method is often used to perform such characterization: constant temperature with variable thermal power input. Maximum power point tracking (MPPT) methods for TEG systems are mostly tested under steady-state conditions for different constant input temperatures. However, for most TEG applications, the input temperature gradient changes, exposing the MPPT to variable tracking conditions. An example is the exhaust pipe on hybrid vehicles, for which, because of the intermittent operation of the internal combustion engine, the TEG and its MPPT controller are exposed to a cyclic temperature profile. Furthermore, there are no guidelines on how fast the MPPT must be under such dynamic conditions. In the work discussed in this paper, temperature gradients for TEG integrated in several applications were evaluated; the results showed temperature variation up to 5°C/s for TEG systems. Electrical characterization of a calcium-manganese oxide TEG was performed at steady-state for different input temperatures and a maximum temperature of 401°C. By using electrical data from characterization of the oxide module, a solar array simulator was emulated to perform as a TEG. A trapezoidal temperature profile with different gradients was used on the TEG simulator to evaluate the dynamic MPPT efficiency. It is known that the perturb and observe (P&O) algorithm may have difficulty accurately tracking under rapidly changing conditions. To solve this problem, a compromise must be found between the magnitude of the increment and the sampling frequency of the control algorithm. The standard P&O performance was evaluated experimentally by using different temperature gradients for different MPPT sampling frequencies, and efficiency values are provided for all cases. The results showed that a tracking speed of 2.5 Hz can be successfully implemented on a TEG
Fast calculation of the maximum power point of photovoltaic generators under partial shading
Carlos Andres Ramos-Paja
2016-09-01
Full Text Available This paper presents a method to calculate the energy production of photovoltaic generators considering partial shading or mismatched conditions. The proposed method is based on the complete one-diode model including the bypass diode in its exponential form, where the current and voltage values of the modules composing the photovoltaic panel array are calculated without using the Lambert-W function. In addition, the method introduces a procedure to calculate the vicinity of the maximum power points, which enables the reduction of the operations required to obtain the global maximum. The proposed method provides short simulation times and high accuracy. On the other hand, since the method does not require complex mathematical functions, it can be implemented straightforwardly on known software packages and development languages such as C and C++. Those characteristics make this method a useful tool to evaluate the economic viability and return-of-investment time of photovoltaic installations. Simulation results and comparisons with a classical procedure confirm the good performance of the proposed method in terms of execution time and accuracy.
Favarel, C.; Champier, D.; Bédécarrats, J. P.; Kousksou, T.; Strub, F.
2012-06-01
According to the International Energy Agency, 1.4 billion people are without electricity in the poorest countries and 2.5 billion people rely on biomass to meet their energy needs for cooking in developing countries. The use of cooking stoves equipped with small thermoelectric generator to provide electricity for basic needs (LED, cell phone and radio charging device) is probably a solution for houses far from the power grid. The cost of connecting every house with a landline is a lot higher than dropping thermoelectric generator in each house. Thermoelectric generators have very low efficiency but for isolated houses, they might become really competitive. Our laboratory works in collaboration with plane`te-bois (a non governmental organization) which has developed energy-efficient multifunction (cooking and hot water) stoves based on traditional stoves designs. A prototype of a thermoelectric generator (Bismuth Telluride) has been designed to convert a small part of the energy heating the sanitary water into electricity. This generator can produce up to 10 watts on an adapted load. Storing this energy in a battery is necessary as the cooking stove only works a few hours each day. As the working point of the stove varies a lot during the use it is also necessary to regulate the electrical power. An electric DC DC converter has been developed with a maximum power point tracker (MPPT) in order to have a good efficiency of the electronic part of the thermoelectric generator. The theoretical efficiency of the MMPT converter is discussed. First results obtained with a hot gas generator simulating the exhaust of the combustion chamber of a cooking stove are presented in the paper.
Advanced Power Management of a Telehandler using Electronic Load Sensing
Hansen, Rico Hjerm
2009-01-01
-sharing, power-sharing, anti-stall and high pressure protection to electronic control. These features are integrated into the developed control structure, which is implemented and tested. The ability of electronically controlling the position of the swash-plate in a variable-displacement pump is an essential...... part of the developed control solution. Hence, the development of a control structure for electronic control of a variable-displacement axial piston pump using a three-way servo valve is also treated....... application, a telehandler, can be replaced with electronic control, i.e. Electronic Load Sensing (ELS). The motivation for ELS is the potentials of better dynamic performance and system utilization, along with reduced mechanical complexity by transferring features as pump pressure control, flow...
From Packet to Power Switching: Digital Direct Load Scheduling
Alizadeh, Mahnoosh; Thomas, Robert J
2012-01-01
At present, the power grid has tight control over its dispatchable generation capacity but a very coarse control on the demand. Energy consumers are shielded from making price-aware decisions, which degrades the efficiency of the market. This state of affairs tends to favor fossil fuel generation over renewable sources. Because of the technological difficulties of storing electric energy, the quest for mechanisms that would make the demand for electricity controllable on a day-to-day basis is gaining prominence. The goal of this paper is to provide one such mechanisms, which we call Digital Direct Load Scheduling (DDLS). DDLS is a direct load control mechanism in which we unbundle individual requests for energy and digitize them so that they can be automatically scheduled in a cellular architecture. Specifically, rather than storing energy or interrupting the job of appliances, we choose to hold requests for energy in queues and optimize the service time of individual appliances belonging to a broad class whi...
2016-01-01
Photovoltaic (PV) systems have non-linear characteristics that generate maximum power at one particular operating point. Environmental factors such as irradiance and temperature variations greatly affect the maximum power point (MPP). Diverse offline and online techniques have been introduced for tracking the MPP. Here, to track the MPP, an augmented-state feedback linearized (AFL) non-linear controller combined with an artificial neural network (ANN) is proposed. This approach linearizes the...
Comparative Study of Maximum Power Point Tracking Techniques for Photovoltaic Systems
Fernando Lessa Tofoli
2015-01-01
Full Text Available The generation of electricity from photovoltaic (PV arrays has been increasingly considered as a prominent alternative to fossil fuels. However, the conversion efficiency is typically low and the initial cost is still appreciable. A required feature of a PV system is the ability to track the maximum power point (MPP of the PV array. Besides, MPP tracking (MPPT is desirable in both grid-connected and stand-alone photovoltaic systems because the solar irradiance and temperature change throughout the day, as well as along seasons and geographical conditions, also leading to the modification of the I×V (current versus voltage and P×V (power versus voltage curves of the PV module. MPPT is also justified by the relatively high cost of the energy generated by PV systems if compared with other sources. Since there are various MPPT approaches available in the literature, this work presents a comparative study among four popular techniques, which are the fixed duty cycle method, constant voltage (CV, perturb and observe (P&O, and incremental conductance (IC. It considers different operational climatic conditions (i.e., irradiance and temperature, since the MPP is nonlinear with the environment status. PSIM software is used to validate the assumptions, while relevant results are discussed in detail.
A fast method of maximum power point tracking for PV%一种快速的光伏最大功率点跟踪方法
高志强; 王建赜; 纪延超; 谭光慧; 张举良
2012-01-01
太阳能电池的输出功率受外界温度、光照强度和负载影响具有特殊的非线性.为了使输出功率始终工作在最大点处从而提高系统的整体效率,最大功率点跟踪在光伏系统中有很重要的意义,通过理论仿真分析,在温度不变的情况下,太阳能电池的输出电压变化不大,随着光照强度的变化最大功率点近似在一条直线上,和输出电流成线性关系.所采用新颖最大功率点跟踪方法是根据估算的最大功率点和输出电流成线性关系把P-I输出曲线划分成两个独立区域,在区域Ⅰ和区域Ⅱ分别采用变步长的观测比较法和变斜率的观测比较法快速调节输出电流使其接近或者等于最大功率点电流,达到快速跟踪最大功率点的目的.通过Matlab/Simulink软件仿真结果表明此种方法与扰动观测控制相比较,不仅能保证快速的跟踪光伏模块最大输出功率点,而且不会引起在最大功率点附近频繁波动,最后通过实验加以验证.%In order to ensure that the PV module always works at the maximum point of power to increase the system's overall efficiency, maximum power point tracking is crucial, since the output power of solar panels is influenced by special nonlinear conditions, such as outside temperature, light intensity and impact of load. This paper presents a novel photovoltaic maximum power point tracking method. The theoretical simulation shows that while the temperature is constant, the output voltage changes little, and with the change of the light intensity, the maximum power point approximates into a straight line, namely the maximum power point and the corresponding output current have a linear relationship. The proposed maximum power point tracking method is based on the maximum power point estimated and the corresponding linear output current curve, dividing the P-I output curve into two regions, and adjusting the output current through different control criteria
Klumpner, Christian; Blaabjerg, Frede
2004-01-01
Normally, a power converter has one supply port to connect to the power grid and one output port to connect to an AC load that requires variable voltage and variable frequency. Converter topologies with multiple output ports, the so-called multi-drive converters are also used in order to share......) and continuously adjust these power fractions will become a desired feature. This paper presents a generalized Direct Power Converter topology, which is able to connect to multiple AC supplies proving complete decoupling and no circulating power between the input ports and to independently control multiple AC...... the cost of an active front-end rectifier. As the trend on the energy market is towards deregulation, new converter topologies are needed to allow independent producers/consumers to connect to multiple distribution grids in order to minimize the electricity price. Having the possibility to adjust smoothly...
Senjyu, Tomonobu; Ochi, Yasutaka; Kikunaga, Yasuaki; Tokudome, Motoki; Yona, Atsushi; Muhando, Endusa Billy; Urasaki, Naomitsu [Department of Electrical and Electronics Engineering, Faculty of Engineering, University of the Ryukyus, 1 Senbaru, Nishihara-cho, Nakagami, Okinawa 903-0213 (Japan); Funabashi, Toshihisa [Meidensha Corporation, ThinkPark Tower, 2-1-1, Ohsaki, Shinagawa-ku, Tokyo 141-6029 (Japan)
2009-04-15
This paper proposes a technique that determines the optimal windmill operation speed and the optimal rotor flux. Moreover, the position and speed sensor-less wind generation system using the electromotive voltage observer to estimate rotor position and full-order observer to estimate rotor speed and the windmill output torque are proposed. The position and speed sensor-less maximum power point of wind power generation system is controlled by using the above estimated values, optimized windmill operation speed for maximum output power and optimized rotor flux for minimum generator losses. The effectiveness of the position and speed sensor-less maximum power point tracking control for wind power generation system with squirrel cage induction generator is verified by simulations. The simulation results confirm that the proposed method can estimate the operation speed efficiently. (author)
The research of the maximum wind speed in Tomsk and calculations of dynamic load on antenna systems
Belan, B.; Belan, S.; Romanovskiy, O.; Girshtein, A.; Yanovich, A.; Baidali, S.; Terehov, S.
2017-01-01
The work is concerned with calculations and analysis of the maximum wind speed in Tomsk city. The data for analysis were taken from the TOR-station located in the north-eastern part of the city. The TOR-station sensors to measure a speed and a direction of wind are installed on the 10-meter meteorological mast. Wind is measured by M-63, which uses the standard approach and the program with one-minute averaging for wind gusts recording as well. According to the measured results in the research performed, the estimation of the dynamic and wind load on different types of antenna systems was performed. The work shows the calculations of wind load on ten types of antenna systems, distinguished by their different constructions and antenna areas. For implementation of calculations, we used methods developed in the Central Research and Development Institute of Building Constructions named after V.A. Kucherenko. The research results could be used for design engineering of the static antenna systems and mobile tracking systems for the distant objects.
Load optimised piezoelectric generator for powering battery-less TPMS
Blažević, D.; Kamenar, E.; Zelenika, S.
2013-05-01
The design of a piezoelectric device aimed at harvesting the kinetic energy of random vibrations on a vehicle's wheel is presented. The harvester is optimised for powering a Tire Pressure Monitoring System (TPMS). On-road experiments are performed in order to measure the frequencies and amplitudes of wheels' vibrations. It is hence determined that the highest amplitudes occur in an unperiodic manner. Initial tests of the battery-less TPMS are performed in laboratory conditions where tuning and system set-up optimization is achieved. The energy obtained from the piezoelectric bimorph is managed by employing the control electronics which converts AC voltage to DC and conditions the output voltage to make it compatible with the load (i.e. sensor electronics and transmitter). The control electronics also manages the sleep/measure/transmit cycles so that the harvested energy is efficiently used. The system is finally tested in real on-road conditions successfully powering the pressure sensor and transmitting the data to a receiver in the car cockpit.
Bifurcation Analysis of a DC-DC Bidirectional Power Converter Operating with Constant Power Loads
Cristiano, Rony; Pagano, Daniel J.; Benadero, Luis; Ponce, Enrique
Direct current (DC) microgrids (MGs) are an emergent option to satisfy new demands for power quality and integration of renewable resources in electrical distribution systems. This work addresses the large-signal stability analysis of a DC-DC bidirectional converter (DBC) connected to a storage device in an islanding MG. This converter is responsible for controlling the balance of power (load demand and generation) under constant power loads (CPLs). In order to control the DC bus voltage through a DBC, we propose a robust sliding mode control (SMC) based on a washout filter. Dynamical systems techniques are exploited to assess the quality of this switching control strategy. In this sense, a bifurcation analysis is performed to study the nonlinear stability of a reduced model of this system. The appearance of different bifurcations when load parameters and control gains are changed is studied in detail. In the specific case of Teixeira Singularity (TS) bifurcation, some experimental results are provided, confirming the mathematical predictions. Both a deeper insight in the dynamic behavior of the controlled system and valuable design criteria are obtained.
Esfandiar, Habib; KoraYem, Moharam Habibnejad [Islamic Azad University, Tehran (Iran, Islamic Republic of)
2015-09-15
In this study, the researchers try to examine nonlinear dynamic analysis and determine Dynamic load carrying capacity (DLCC) in flexible manipulators. Manipulator modeling is based on Timoshenko beam theory (TBT) considering the effects of shear and rotational inertia. To get rid of the risk of shear locking, a new procedure is presented based on mixed finite element formulation. In the method proposed, shear deformation is free from the risk of shear locking and independent of the number of integration points along the element axis. Dynamic modeling of manipulators will be done by taking into account small and large deformation models and using extended Hamilton method. System motion equations are obtained by using nonlinear relationship between displacements-strain and 2nd PiolaKirchoff stress tensor. In addition, a comprehensive formulation will be developed to calculate DLCC of the flexible manipulators during the path determined considering the constraints end effector accuracy, maximum torque in motors and maximum stress in manipulators. Simulation studies are conducted to evaluate the efficiency of the method proposed taking two-link flexible and fixed base manipulators for linear and circular paths into consideration. Experimental results are also provided to validate the theoretical model. The findings represent the efficiency and appropriate performance of the method proposed.
LIN; Kuang-Jang; LIN; Chii-Ruey
2010-01-01
The Photovoltaic Array has a best optimal operating point where the array operating can obtain the maximum power.However, the optimal operating point can be compromised by the strength of solar radiation,angle,and by the change of environment and load.Due to the constant changes in these conditions,it has become very difficult to locate the optimal operating point by following a mathematical model.Therefore,this study will focus mostly on the application of Fuzzy Logic Control theory and Three-point Weight Comparison Method in effort to locate the optimal operating point of solar panel and achieve maximum efficiency in power generation. The Three-point Weight Comparison Method is the comparison between the characteristic curves of the voltage of photovoltaic array and output power;it is a rather simple way to track the maximum power.The Fuzzy Logic Control,on the other hand,can be used to solve problems that cannot be effectively dealt with by calculation rules,such as concepts,contemplation, deductive reasoning,and identification.Therefore,this paper uses these two kinds of methods to make simulation successively. The simulation results show that,the Three-point Comparison Method is more effective under the environment with more frequent change of solar radiation;however,the Fuzzy Logic Control has better tacking efficiency under the environment with violent change of solar radiation.
Non-intrusive load monitoring based on low frequency active power measurements
Chinthaka Dinesh
2016-03-01
Full Text Available A Non-Intrusive Load Monitoring (NILM method for residential appliances based on active power signal is presented. This method works effectively with a single active power measurement taken at a low sampling rate (1 s. The proposed method utilizes the Karhunen Loéve (KL expansion to decompose windows of active power signals into subspace components in order to construct a unique set of features, referred to as signatures, from individual and aggregated active power signals. Similar signal windows were clustered in to one group prior to feature extraction. The clustering was performed using a modified mean shift algorithm. After the feature extraction, energy levels of signal windows and power levels of subspace components were utilized to reduce the number of possible appliance combinations and their energy level combinations. Then, the turned on appliance combination and the energy contribution from individual appliances were determined through the Maximum a Posteriori (MAP estimation. Finally, the proposed method was modified to adaptively accommodate the usage patterns of appliances at each residence. The proposed NILM method was validated using data from two public databases: tracebase and reference energy disaggregation data set (REDD. The presented results demonstrate the ability of the proposed method to accurately identify and disaggregate individual energy contributions of turned on appliance combinations in real households. Furthermore, the results emphasise the importance of clustering and the integration of the usage behaviour pattern in the proposed NILM method for real households.
Gronewold, A. D.; Alameddine, I.; Anderson, R.; Wolpert, R.; Reckhow, K.
2008-12-01
The United States Environmental Protection Agency (USEPA) total maximum daily load (TMDL) program requires that individual states assess the condition of surface waters and identify those which fail to meet ambient water quality standards. Waters failing to meet those standards must have a TMDL assessment conducted to determine the maximum allowable pollutant load which can enter the water without violating water quality standards. While most of the nearly 30,000 TMDL assessments completed since 1995 use mechanistic or empirical water quality models to forecast water quality conditions under alternative pollutant loading reduction scenarios, few, if any, also simulate water quality conditions under alternative climate change scenarios. As a result, model-based loading reduction requirements (which serve as the cornerstone for implementing water resource management plans, and initiating environmental management infrastructure projects), believed to improve water quality in impaired waters and reinstate their designated use, may misrepresent the actual required reduction when future climate change scenarios are considered. For example, recent research indicates a potential long term future increase in both the number of days between, and the intensity of, individual precipitation events. In coastal terrestrial and aquatic ecosystems, such climate conditions could lead to an increased accumulation of pollutants on the landscape between precipitation events, followed by a washoff event with a relatively high pollutant load. On the other hand, anticipated increases in average temperature and evaporation rate might not only reduce effective rainfall rates (resulting in less energy for transporting pollutants from the landscape) but also reduce the tidal exchange ratio in shallow estuaries (many of which are valuable recreational, commercial, and aesthetic natural resources). Here, we develop and apply a comprehensive watershed-scale model for simulating water quality in
Research on Interactive Control of Electrolytic Aluminum Load and Wind Power Output
Ge Simin
2016-01-01
Full Text Available With the large-scale wind power generation connected to Gansu power grid, electrolytic aluminium load has reached a certain scale at the same time, the vast majority of electrolytic aluminium load directly connects to power grid using 330kV transmission line. According to the physical characteristics and historical data, the continuous adjustment characteristic of electrolytic aluminium load is analysed. Based on this characteristic, a mathematical model for the electrolytic aluminium load is established. Aiming at reducing power network loss and wind power consumption, an optimization model based on the load regulation characteristics of electrolytic aluminium is constructed, which is optimized by particle swarm optimization algorithm. Based on the case data of Gansu power grid, the optimal method based on the load regulation characteristics of electrolytic aluminium is analysed and its feasibility is verified.
Subiyanto
2013-01-01
Full Text Available Photovoltaic (PV system is one of the promising renewable energy technologies. Although the energy conversion efficiency of the system is still low, but it has the advantage that the operating cost is free, very low maintenance and pollution-free. Maximum power point tracking (MPPT is a significant part of PV systems. This paper presents a novel intelligent MPPT controller for PV systems. For the MPPT algorithm, an optimized fuzzy logic controller (FLC using the Hopfield neural network is proposed. It utilizes an automatically tuned FLC membership function instead of the trial-and-error approach. The MPPT algorithm is implemented in a new variant of coupled inductor soft switching boost converter with high voltage gain to increase the converter output from the PV panel. The applied switching technique, which includes passive and active regenerative snubber circuits, reduces the insulated gate bipolar transistor switching losses. The proposed MPPT algorithm is implemented using the dSPACE DS1104 platform software on a DS1104 board controller. The prototype MPPT controller is tested using an agilent solar array simulator together with a 3 kW real PV panel. Experimental test results show that the proposed boost converter produces higher output voltages and gives better efficiency (90% than the conventional boost converter with an RCD snubber, which gives 81% efficiency. The prototype MPPT controller is also found to be capable of tracking power from the 3 kW PV array about 2.4 times more than that without using the MPPT controller.
Chao, R.M.; Ko, S.H.; Lin, I.H. [Department of Systems and Naval Mechatronics Engineering, National Cheng Kung University, Tainan, Taiwan 701 (China); Pai, F.S. [Department of Electronic Engineering, National University of Tainan (China); Chang, C.C. [Department of Environment and Energy, National University of Tainan (China)
2009-12-15
The historically high cost of crude oil price is stimulating research into solar (green) energy as an alternative energy source. In general, applications with large solar energy output require a maximum power point tracking (MPPT) algorithm to optimize the power generated by the photovoltaic effect. This work aims to provide a stand-alone solution for solar energy applications by integrating a DC/DC buck converter to a newly developed quadratic MPPT algorithm along with its appropriate software and hardware. The quadratic MPPT method utilizes three previously used duty cycles with their corresponding power outputs. It approaches the maximum value by using a second order polynomial formula, which converges faster than the existing MPPT algorithm. The hardware implementation takes advantage of the real-time controller system from National Instruments, USA. Experimental results have shown that the proposed solar mechatronics system can correctly and effectively track the maximum power point without any difficulties. (author)
Bayu Prima Juliansyah Putra
2013-09-01
Full Text Available Salah satu aplikasi yang sering digunakan dalam bidang energi terbarukan adalah panel photovoltaic. Panel ini memiliki prinsip kerja berdasarkan efek photovoltaic dimana lempengan logam akan menghasilkan energi listrik apabila diberi intensitas cahaya. Untuk menghasilkan daya keluaran panel yang maksimal, maka diperlukan suatu algoritma yang biasa disebut Maximum Power Point Tracking (MPPT.MPPT yang diterapkan pada sistem photovoltaic berfungsi untuk mengatur nilai tegangan keluaran panel sehingga titik ker-janya beroperasi pada kondisi maksimal. Algoritma MPPT pada panel ini telah dilakukan dengan menggunakan logika fuzzy melalui mikrokontroler Arduino Uno sebagai pem-bangkit sinyal Pulse Width Modulation (PWM yang akan dikirimkan menuju DC-DC Buck Boost Converter. Keluaran dari buck boost converterakan dihubungkan secara langsung dengan buoy weather station untuk menyuplai energi listrik tiap komponen yang berada di dalamnya. Untuk menguji performansi dari algoritma MPPT yang telah dirancang, maka sistem akan diuji menggunakan variasi beban antara metode direct-coupled dengan MPPT menggunakan logika fuzzy. Hasil pengujian menunjukkan bahwa MPPT dengan logika fuzzy dapat menghasilkan daya maksimum daripada direct-coupled. Pada sistem panel photovoltaic ini memiliki range efisiensi 33.07589 % hingga 74.25743 %. Daya mak-simal dapat dicapai oleh sistem untuk tiap variasi beban dan efisiensi maksimal dapat dicapai pada beban 20 Ohm dari hasil pengujian sistem MPPT.
IMPLEMENTATION OF FUZZY LOGIC MAXIMUM POWER POINT TRACKING CONTROLLER FOR PHOTOVOLTAIC SYSTEM
Rasoul Rahmani
2013-01-01
Full Text Available In this study, simulation and hardware implementation of Fuzzy Logic (FL Maximum Power Point Tracking (MPPT used in photovoltaic system with a direct control method are presented. In this control system, no proportional or integral control loop exists and an adaptive FL controller generates the control signals. The designed and integrated system is a contribution of different aspects which includes simulation, design and programming and experimental setup. The resultant system is capable and satisfactory in terms of fastness and dynamic performance. The results also indicate that the control system works without steady-state error and has the ability of tracking MPPs rapid and accurate which is useful for the sudden changes in the atmospheric condition. MATLAB/Simulink software is utilized for simulation and also programming the TMS320F2812 Digital Signal Processor (DSP. The whole system designed and implemented to hardware was tested successfully on a laboratory PV array. The obtained experimental results show the functionality and feasibility of the proposed controller.
Thermodynamics, maximum power, and the dynamics of preferential river flow structures on continents
A. Kleidon
2012-06-01
Full Text Available The organization of drainage basins shows some reproducible phenomena, as exemplified by self-similar fractal river network structures and typical scaling laws, and these have been related to energetic optimization principles, such as minimization of stream power, minimum energy expenditure or maximum "access". Here we describe the organization and dynamics of drainage systems using thermodynamics, focusing on the generation, dissipation and transfer of free energy associated with river flow and sediment transport. We argue that the organization of drainage basins reflects the fundamental tendency of natural systems to deplete driving gradients as fast as possible through the maximization of free energy generation, thereby accelerating the dynamics of the system. This effectively results in the maximization of sediment export to deplete topographic gradients as fast as possible and potentially involves large-scale feedbacks to continental uplift. We illustrate this thermodynamic description with a set of three highly simplified models related to water and sediment flow and describe the mechanisms and feedbacks involved in the evolution and dynamics of the associated structures. We close by discussing how this thermodynamic perspective is consistent with previous approaches and the implications that such a thermodynamic description has for the understanding and prediction of sub-grid scale organization of drainage systems and preferential flow structures in general.
A. Kleidon
2013-01-01
Full Text Available The organization of drainage basins shows some reproducible phenomena, as exemplified by self-similar fractal river network structures and typical scaling laws, and these have been related to energetic optimization principles, such as minimization of stream power, minimum energy expenditure or maximum "access". Here we describe the organization and dynamics of drainage systems using thermodynamics, focusing on the generation, dissipation and transfer of free energy associated with river flow and sediment transport. We argue that the organization of drainage basins reflects the fundamental tendency of natural systems to deplete driving gradients as fast as possible through the maximization of free energy generation, thereby accelerating the dynamics of the system. This effectively results in the maximization of sediment export to deplete topographic gradients as fast as possible and potentially involves large-scale feedbacks to continental uplift. We illustrate this thermodynamic description with a set of three highly simplified models related to water and sediment flow and describe the mechanisms and feedbacks involved in the evolution and dynamics of the associated structures. We close by discussing how this thermodynamic perspective is consistent with previous approaches and the implications that such a thermodynamic description has for the understanding and prediction of sub-grid scale organization of drainage systems and preferential flow structures in general.
Efficiency at maximum power output for an engine with a passive piston
Sano, Tomohiko G.; Hayakawa, Hisao
2016-08-01
Efficiency at maximum power (MP) output for an engine with a passive piston without mechanical controls between two reservoirs is studied theoretically. We enclose a hard core gas partitioned by a massive piston in a temperature-controlled container and analyze the efficiency at MP under a heating and cooling protocol without controlling the pressure acting on the piston from outside. We find the following three results: (i) The efficiency at MP for a dilute gas is close to the Chambadal-Novikov-Curzon-Ahlborn (CNCA) efficiency if we can ignore the sidewall friction and the loss of energy between a gas particle and the piston, while (ii) the efficiency for a moderately dense gas becomes smaller than the CNCA efficiency even when the temperature difference of the reservoirs is small. (iii) Introducing the Onsager matrix for an engine with a passive piston, we verify that the tight coupling condition for the matrix of the dilute gas is satisfied, while that of the moderately dense gas is not satisfied because of the inevitable heat leak. We confirm the validity of these results using the molecular dynamics simulation and introducing an effective mean-field-like model which we call the stochastic mean field model.
Optimized Large-Scale CMB Likelihood And Quadratic Maximum Likelihood Power Spectrum Estimation
Gjerløw, E; Eriksen, H K; Górski, K M; Gruppuso, A; Jewell, J B; Plaszczynski, S; Wehus, I K
2015-01-01
We revisit the problem of exact CMB likelihood and power spectrum estimation with the goal of minimizing computational cost through linear compression. This idea was originally proposed for CMB purposes by Tegmark et al.\\ (1997), and here we develop it into a fully working computational framework for large-scale polarization analysis, adopting \\WMAP\\ as a worked example. We compare five different linear bases (pixel space, harmonic space, noise covariance eigenvectors, signal-to-noise covariance eigenvectors and signal-plus-noise covariance eigenvectors) in terms of compression efficiency, and find that the computationally most efficient basis is the signal-to-noise eigenvector basis, which is closely related to the Karhunen-Loeve and Principal Component transforms, in agreement with previous suggestions. For this basis, the information in 6836 unmasked \\WMAP\\ sky map pixels can be compressed into a smaller set of 3102 modes, with a maximum error increase of any single multipole of 3.8\\% at $\\ell\\le32$, and a...
Gonzalez, L.G. [Departamento de Electronica y Comunicaciones, Universidad de los Andes, nucleo la Hechicera, 5101 Merida (Venezuela); Figueres, E.; Garcera, G. [Grupo de Sistemas Electronicos Industriales, Universidad Politecnica de Valencia, Camino de vera s/n, 46022 Valencia (Spain); Carranza, O. [Escuela Superior de Computo, Instituto Politecnico Nacional, Av. Juan de Dios Batiz s/n, 07738 DF (Mexico)
2010-07-15
This paper presents an improved maximum-power-point tracking algorithm for wind-energy-conversion-systems. The proposed method significantly reduces the turbine mechanical stress with regard to conventional techniques, so that both the maintenance needs and the medium time between failures are expected to be improved. To achieve these objectives, a sensorless speed control loop receives its reference signal from a modified Perturb and Observe algorithm, in which the typical steps on the reference speed have been substituted by a fixed and well-defined slope ramp signal. As a result, it is achieved a soft dynamic response of both the torque and the speed of the wind turbine, so that the whole system suffers from a lower mechanical stress than with conventional P and O techniques. The proposed method has been applied to a wind turbine based on a permanent magnet synchronous generator operating at variable speed, which is connected to the distribution grid by means of a back to back converter. (author)
Efficiency at maximum power and efficiency fluctuations in a linear Brownian heat-engine model
Park, Jong-Min; Chun, Hyun-Myung; Noh, Jae Dong
2016-07-01
We investigate the stochastic thermodynamics of a two-particle Langevin system. Each particle is in contact with a heat bath at different temperatures T1 and T2 (autonomous heat engine performing work against the external driving force. Linearity of the system enables us to examine thermodynamic properties of the engine analytically. We find that the efficiency of the engine at maximum power ηM P is given by ηM P=1 -√{T2/T1 } . This universal form has been known as a characteristic of endoreversible heat engines. Our result extends the universal behavior of ηM P to nonendoreversible engines. We also obtain the large deviation function of the probability distribution for the stochastic efficiency in the overdamped limit. The large deviation function takes the minimum value at macroscopic efficiency η =η ¯ and increases monotonically until it reaches plateaus when η ≤ηL and η ≥ηR with model-dependent parameters ηR and ηL.
Short-term load forecasting study of wind power based on Elman neural network
Tian, Xinran; Yu, Jing; Long, Teng; Liu, Jicheng
2017-01-01
Since wind power has intermittent, irregular and volatility nature, improving load forecasting accuracy of wind power has significant influence on controlling wind system and guarantees stable operation of power grids. This paper constructed the wind farm loading forecasting in short-term based on Elman neural network, and made a numerical example analysis. . Examples show that, using input delayed of feedback Elman neural network, can reflect the inherent laws of wind load operation better, so as to present a new idea for short-term load forecasting of wind power.
EXCAVATION OF PITS (CHANNELS BY IMPACT OF PULSE POWER LOADING
Anakhaev Koshkinbai Nazirovich
2017-08-01
Full Text Available The paper provides an innovative hydromechanical solution of the problem of profiles development of pits and channels by impact of pulse (blasting power load on a surface of homogeneous soil mass, for example, when excavating solid rocks, frozen soil, etc. Thus, soil would be considered as an ideal heavy liquid (disregarding its mechanical strength and plastic properties. The solution of this problem is achieved by the method of consecutive conformal mappings of physical flow region (in the form of Kirchhoff complex on the region of complex potential (in the form of a rectangle. Thus, the new technique of geometrical image generation of the latter in the presence in the flow region of a fixed point with discontinuous variations of pressure head-flow function and the direction of speed of flow and representation of an elliptic sine of Jacobi by means of elementary functions are used. The received analytical functional dependencies allow to determine an outline of a funnel of the soil ejection and all the required hydromechanical characteristics of flow (head-flow function, function of flow, speed of flow, etc.. Thus, the soil ejection funnel outline (for a benchmark problem completely coincides with subproduct of the known rigorous solution of Lavrentyev-Kuznetsov.
A robust decentralized load frequency controller for interconnected power systems.
Dong, Lili; Zhang, Yao; Gao, Zhiqiang
2012-05-01
A novel design of a robust decentralized load frequency control (LFC) algorithm is proposed for an inter-connected three-area power system, for the purpose of regulating area control error (ACE) in the presence of system uncertainties and external disturbances. The design is based on the concept of active disturbance rejection control (ADRC). Estimating and mitigating the total effect of various uncertainties in real time, ADRC is particularly effective against a wide range of parameter variations, model uncertainties, and large disturbances. Furthermore, with only two tuning parameters, the controller provides a simple and easy-to-use solution to complex engineering problems in practice. Here, an ADRC-based LFC solution is developed for systems with turbines of various types, such as non-reheat, reheat, and hydraulic. The simulation results verified the effectiveness of the ADRC, in comparison with an existing PI-type controller tuned via genetic algorithm linear matrix inequalities (GALMIs). The comparison results show the superiority of the proposed solution. Moreover, the stability and robustness of the closed-loop system is studied using frequency-domain analysis.
More power and less loads in wind farms. 'Heat and flux'
Corten, G.P.; Schaak, P. [ECN Wind Energy, Petten (Netherlands)
2004-11-01
We consider a farm as a single energy extracting body instead of a superposition of individual energy extractors, i.e. wind turbines. As a result we found two new hypotheses called Heat and Flux. Both hypotheses reveal that the classical operation of turbines in a wind farm at the Lanchester-Betz optimum does not lead to maximum farm output. However, when the turbines at the windward side of the farm are operated below their optimum, then the power of the turbines under the lee increases in such a way that the net farm production increases slightly. Next to this production advantage of Heat and Flux operation there is also a loading advantage. The average axial loading of the upwind turbines of a farm is reduced in a 'Heat and Flux'-farm. As a result those turbines generate less turbines so that the fatigue loads of the downwind turbines reduce too. The results were confirmed by in a boundary layer tunnel by means of differential measurements between a 'Heat and Flux'-farm and a classical farm.
Service Oriented Architectural Model for Load Flow Analysis in Power Systems
Muthu, Balasingh Moses; Veilumuthu, Ramachandran; Ponnusamy, Lakshmi
2011-07-01
The main objective of this paper is to develop the Service Oriented Architectural (SOA) Model for representation of power systems, especially of computing load flow analysis of large interconnected power systems. The proposed SOA model has three elements namely load flow service provider, power systems registry and client. The exchange of data using XML makes the power system services standardized and adaptable. The load flow service is provided by the service provider, which is published in power systems registry for enabling universal visibility and access to the service. The message oriented style of SOA using Simple Object Access Protocol (SOAP) makes the service provider and the power systems client to exist in a loosely coupled environment. This proposed model, portraits the load flow services as Web services in service oriented environment. To suit the power system industry needs, it easily integrates with the Web applications which enables faster power system operations.
Lakshmanan, Venkatachalam; Marinelli, Mattia; Kosek, Anna Magdalena;
2015-01-01
This paper describes the impacts of different types of DR (demand response) activation on TCLs' (thermostatically controlled loads) aggregated power. The different parties: power system operators, DR service providers (or aggregators) and consumers, have different objectives in relation to DR...
A New Fuzzy-Based Maximum Power Point Tracker for a Solar Panel Based on Datasheet Values
Ali Kargarnejad
2013-01-01
Full Text Available Tracking maximum power point of a solar panel is of interest in most of photovoltaic applications. Solar panel modeling is also very interesting exclusively based on manufacturers data. Knowing that the manufacturers generally give the electrical specifications of their products at one operating condition, there are so many cases in which the specifications in other conditions are of interest. In this research, a comprehensive one-diode model for a solar panel with maximum obtainable accuracy is fully developed only based on datasheet values. The model parameters dependencies on environmental conditions are taken into consideration as much as possible. Comparison between real data and simulations results shows that the proposed model has maximum obtainable accuracy. Then a new fuzzy-based controller to track the maximum power point of the solar panel is also proposed which has better response from speed, accuracy and stability point of view respect to the previous common developed one.
Park, Jungyong; Kim, Shiho
2012-06-01
An analog maximum power point tracking (MPPT) circuit for a thermoelectric generator (TEG) is proposed. We show that the peak point of the voltage conversion gain of a boost DC-DC converter with an input voltage source having an internal resistor is the maximum power point of the TEG. The key characteristic of the proposed MPPT controller is that the duty ratio of the input clock pulse to the boost DC-DC converter shifts toward the maximum power point of the TEG by seeking the peak gain point of the boost DC-DC converters. The proposed MPPT technique provides a simple and useful analog MPPT solution, without employing digital microcontroller units.
A New Fuzzy-Based Maximum Power Point Tracker for a Solar Panel Based on Datasheet Values
Ali Kargarnejad; Mohsen Taherbaneh; Amir Hosein Kashefi
2013-01-01
Tracking maximum power point of a solar panel is of interest in most of photovoltaic applications. Solar panel modeling is also very interesting exclusively based on manufacturers data. Knowing that the manufacturers generally give the electrical specifications of their products at one operating condition, there are so many cases in which the specifications in other conditions are of interest. In this research, a comprehensive one-diode model for a solar panel with maximum obtainable accuracy...
Harry X.ZHANG; Shaw L.YU
2008-01-01
One of the key challenges in the total max-imum daily load (TMDL) development process is how to define the critical condition for a receiving water-body. The main concern in using a continuous simu-lation approach is the absence of any guarantee that the most critical condition will be captured during the selected representative hydrologic period, given the scar-city of long-term continuous data. The objectives of this paper are to clearly address the critical condition in the TMDL development process and to compare continu-ous and evEnt-based approaches in defining critical con-dition during TMDL development for a waterbody impacted by both point and nonpoint source pollution. A practical, event-based critical flow-storm (CFS) approach was developed to explicitly addresses the crit-ical condition as a combination of a low stream flow and a storm event of a selected magnitude, both having cer-tain frequencies of occurrence. This paper illustrated the CFS concept and provided its theoretical basis using a derived analytical conceptual model. The CFS approach clearly defined a critical condition, obtained reasonable results and could be considered as an alternative method in TMDL development.
Systems and methods for providing power to a load based upon a control strategy
Perisic, Milun; Kajouke, Lateef A; Ransom, Ray M
2013-12-24
Systems and methods are provided for an electrical system. The electrical system includes a load, an interface configured to receive a voltage from a voltage source, and a controller configured to receive the voltage from the voltage source through the interface and to provide a voltage and current to the load. Wherein, when the controller is in a constant voltage mode, the controller provides a constant voltage to the load, when the controller is in a constant current mode, the controller provides a constant current to the load, and when the controller is in a constant power mode, the controller provides a constant power to the load.
The Betz-Joukowsky limit for the maximum power coefficient of wind turbines
Okulov, Valery; van Kuik, G.A.M.
2009-01-01
The article addresses to a history of an important scientific result in wind energy. The maximum efficiency of an ideal wind turbine rotor is well known as the ‘Betz limit’, named after the German scientist that formulated this maximum in 1920. Also Lanchester, a British scientist, is associated...
Use of fuzzy techniques for analysis of dynamic loads in power systems
无
2001-01-01
Presents the use of fuzzy techniques for analysis of dynamic load characteristics of power systems to identify the voltage stability (collapse) of a weak bus and concludes from the consistent results obtained that this is a useful tool for analysis of load charactersitics of sophiscated power systems and their components.
Smit, Jeroen; Berghammer, Lars O.; Navalkar, Sachin;
2014-01-01
In this paper an extension of the spectrum of applicability of rotors with active aerody-namic devices is presented. Besides the classical purpose of load alleviation, a secondary objective is established: power capture optimization. As a _rst step, wind speed regions that contribute little...
Smit, Jeroen; Bernhammer, Lars O.; Navalkar, Sachin T.;
2016-01-01
An extension of the spectrum of applicability of rotors with active aerodynamic devices is presented in this paper. Besides the classical purpose of load alleviation, a secondary objective is established: optimization of power capture. As a first step, wind speed regions that contribute little...
Wang, Kezhi
2014-10-01
Bit error rate (BER) and outage probability for amplify-and-forward (AF) relaying systems with two different channel estimation methods, disintegrated channel estimation and cascaded channel estimation, using pilot-aided maximum likelihood method in slowly fading Rayleigh channels are derived. Based on the BERs, the optimal values of pilot power under the total transmitting power constraints at the source and the optimal values of pilot power under the total transmitting power constraints at the relay are obtained, separately. Moreover, the optimal power allocation between the pilot power at the source, the pilot power at the relay, the data power at the source and the data power at the relay are obtained when their total transmitting power is fixed. Numerical results show that the derived BER expressions match with the simulation results. They also show that the proposed systems with optimal power allocation outperform the conventional systems without power allocation under the same other conditions. In some cases, the gain could be as large as several dB\\'s in effective signal-to-noise ratio.
Maheshwari, Govind; Chaudhary, S; Somani, S.K
2010-01-01
The efficient power, defined as the product of power output and efficiency of the engine, is taken as the objective for performance analysis and optimization of an endoreversible combined Carnot heat...
Supervisor Circuit Decides When Solar Array Can Power A Load
2011-01-01
Sun powered electronic devices may suffer in twilight conditions. In particular microprocessors (widely used to perform solar power conditioning, such MPPTs) do not like unstable power or smooth edges on power on. The proposed circuit offers some nice supervision performance at the price of 3 transistors.
Design and Stability of Load-Side Primary Frequency Control in Power Systems
Zhao, CH; Topcu, U; Li, N; Low, S
2014-05-01
We present a systematic method to design ubiquitous continuous fast-acting distributed load control for primary frequency regulation in power networks, by formulating an optimal load control (OLC) problem where the objective is to minimize the aggregate cost of tracking an operating point subject to power balance over the network. We prove that the swing dynamics and the branch power flows, coupled with frequency-based load control, serve as a distributed primal-dual algorithm to solve OLC. We establish the global asymptotic stability of a multimachine network under such type of load-side primary frequency control. These results imply that the local frequency deviations on each bus convey exactly the right information about the global power imbalance for the loads to make individual decisions that turn out to be globally optimal. Simulations confirm that the proposed algorithm can rebalance power and resynchronize bus frequencies after a disturbance with significantly improved transient performance.
Hao Dong
2015-01-01
Full Text Available In order to implement the uniform load distribution of the power-split transmission system, a pseudostatic model is built. Based on the loaded tooth contact analysis (LTCA technique, the actual meshing process of each gear pair is simulated and the fitting curve of time-varying mesh stiffness is obtained. And then, the torsional angle deformation compatibility conditions are proposed according to the closed-loop characteristic of power flow, which will be combined with the torque equilibrium conditions and elastic support conditions to calculate the transfer torque of each gear pair. Finally, the load-sharing coefficient of the power-split transmission system is obtained, and the influences of the installation errors are analyzed. The results show that the above-mentioned installation errors comprehensively influence the load-sharing characteristics, and the reduction of only one error could not effectively achieve perfect load-sharing characteristics. Allowing for the spline clearance floating and constrained by the radial spacing ring, the influence of the floating pinion is analyzed. It shows that the floating pinion can improve the load-sharing characteristics. Through the comparison between the theoretical and related experimental data, the reasonability and feasibility of the above-proposed method and model are verified.
Load Mitigation and Optimal Power Capture for Variable Speed Wind Turbine in Region 2
Saravanakumar Rajendran
2015-01-01
Full Text Available This paper proposes the two nonlinear controllers for variable speed wind turbine (VSWT operating at below rated wind speed. The objective of the controller is to maximize the energy capture from the wind with reduced oscillation on the drive train. The conventional controllers such as aerodynamic torque feedforward (ATF and indirect speed control (ISC are adapted initially, which introduce more power loss, and the dynamic aspects of WT are not considered. In order to overcome the above drawbacks, modified nonlinear static state with feedback estimator (MNSSFE and terminal sliding mode controller (TSMC based on Modified Newton Raphson (MNR wind speed estimator are proposed. The proposed controllers are simulated with nonlinear FAST (fatigue, aerodynamics, structures, and turbulence WT dynamic simulation for different mean wind speeds at below rated wind speed. The frequency analysis of the drive train torque is done by taking the power spectral density (PSD of low speed shaft torque. From the result, it is found that a trade-off is to be maintained between the transient load on the drive train and maximum power capture.
Hu, Weihao; Su, Chi; Chen, Zhe;
2011-01-01
Since the hourly spot market price is available one day ahead in Denmark, the price could be transferred to the consumers and they may shift some of their loads from high price periods to the low price periods in order to save their energy costs. The optimal load response to an electricity price...... price is proposed. A 17-bus power system with high wind power penetrations, which resembles the Eastern Danish power system, is chosen as the study case. Simulation results show that the optimal load response to electricity prices is an effective measure to improve the small signal stability of power...
Sheng, Shiqi; Tu, Z C
2015-02-01
We present a unified perspective on nonequilibrium heat engines by generalizing nonlinear irreversible thermodynamics. For tight-coupling heat engines, a generic constitutive relation for nonlinear response accurate up to the quadratic order is derived from the stalling condition and the symmetry argument. By applying this generic nonlinear constitutive relation to finite-time thermodynamics, we obtain the necessary and sufficient condition for the universality of efficiency at maximum power, which states that a tight-coupling heat engine takes the universal efficiency at maximum power up to the quadratic order if and only if either the engine symmetrically interacts with two heat reservoirs or the elementary thermal energy flowing through the engine matches the characteristic energy of the engine. Hence we solve the following paradox: On the one hand, the quadratic term in the universal efficiency at maximum power for tight-coupling heat engines turned out to be a consequence of symmetry [Esposito, Lindenberg, and Van den Broeck, Phys. Rev. Lett. 102, 130602 (2009); Sheng and Tu, Phys. Rev. E 89, 012129 (2014)]; On the other hand, typical heat engines such as the Curzon-Ahlborn endoreversible heat engine [Curzon and Ahlborn, Am. J. Phys. 43, 22 (1975)] and the Feynman ratchet [Tu, J. Phys. A 41, 312003 (2008)] recover the universal efficiency at maximum power regardless of any symmetry.
Sclocchi, M.
2010-07-01
This article analyzes the problem of lost socks in the production of electricity caused by partial shading of a photovoltaic system. introducing the advantages of distributed maximum power point tracking system, MPPT the level of the panel and is the outcome of real cases with different technology Solar Magic. (Author)
Artificial bee colony algorithm for economic load dispatch with wind power energy
Safari Amin
2016-01-01
Full Text Available This paper presents an efficient Artificial Bee Colony (ABC algorithm for solving large scale economic load dispatch (ELD problems in power networks. To realize the ELD, the valve-point loading effect, system load demand, power losses, ramp rate limits and prohibited operation zones are considered here. Simulations were performed on four different power systems with 3, 6, 15 and 40 generating units and the results are compared with two forms of power systems, one power system is with a wind power generator and other power system is without a wind power generator. The results of this study reveal that the proposed approach is able to find appreciable ELD solutions than those of previous algorithms.
王琴; 姜丰; 钟清瑶
2012-01-01
The output power of photovoltaic cells changes with the external environment (light intensity, ambient temperature) and load. It is necessary to track the maximum power point of solar cell array rapidry and accurately to improve the utilizabon efficiency of solar cell array. In order to further improve the efficiency of photovoltaic power generation system, a method based on fuzzy logic dual-loop control of the maximum power point tracking of photovoltaic power generation system was presented, which added an inner loop of the fuzzy control based on the former fuzzy control. The simulation verifies that the double-loop fuzzy control method is more efficient and can effectively eliminate the oscillations around the maximum power point. The results show that this maximum power point tracking algorithm can track the maximum power point of photovoltaic power generation system rapidfy and accurately and can improve the static and dynamic performance of the photovoltaic power system.%光伏阵列的输出功率随外部环境(光照强度、环境温度)和负载的变化而变化,为充分发挥光伏器件的效能,需采用有效率的最大功率点跟踪方法.在分析光伏系统中最大功率点跟踪的问题之后,为了能够进一步提高光伏发电系统的效率和系统的稳定性,提出了一种基于模糊逻辑的双环控制的最大功率点跟踪的方法,在以往模糊控制环节的基础上再加入一个内环的模糊控制,搭建了光伏发电系统的仿真模型,通过验证表明双环模糊控制法比传统方法有更高的效率和更高的精度,并且能有效地减小系统功率损耗,且具有能同时兼顾跟踪精度和响应速度的优点.研究对比之后证实此种方法提高了系统的输出功率,保持了系统稳定,提高光伏系统MPPT控制的鲁棒性和精确性.
Lin, Whei-Min; Hong, Chih-Ming [Department of Electrical Engineering, National Sun Yat-Sen University, Kaohsiung 80424 (China)
2010-06-15
To achieve maximum power point tracking (MPPT) for wind power generation systems, the rotational speed of wind turbines should be adjusted in real time according to wind speed. In this paper, a Wilcoxon radial basis function network (WRBFN) with hill-climb searching (HCS) MPPT strategy is proposed for a permanent magnet synchronous generator (PMSG) with a variable-speed wind turbine. A high-performance online training WRBFN using a back-propagation learning algorithm with modified particle swarm optimization (MPSO) regulating controller is designed for a PMSG. The MPSO is adopted in this study to adapt to the learning rates in the back-propagation process of the WRBFN to improve the learning capability. The MPPT strategy locates the system operation points along the maximum power curves based on the dc-link voltage of the inverter, thus avoiding the generator speed detection. (author)
Experimental study of a technique for load measurement of powered supports
Hua Zhu; Shirong Ge; Xiaolong Huang; Sumei Dai
2004-01-01
Despite the increasing popularity of mechanized coal mining, there are no convenient and accurate means available to measure the loads of powered supports. The measurement of such loads is important for monitoring mine pressure and ensuring production safety. The load-carrying features of a powered support were used to develop a method for load measurement using the magnetoelastic principle. A cross bridge-type magnetoelastic stress sensor was designed for the support structures to measure the different parts of the supports. Tests on single-body hydraulic cylinders and simulated linkages showed that an approximately linear relationship between the values of the sensor output signal and the loads borne by the hydraulic cylinders or linkages. The results were used to analyze the load-carrying measurements of powered supports with the cross bridge-type magnetoelastic stress sensor.
A. Arivoli
2014-01-01
Full Text Available In wireless ad hoc network scenario, Cross-layer design is emerging, important in wireless ad hoc network and the power control methods. Power control is the intelligent selection of transmit power in a communication to achieve the better performance within the system. Cross-layer is used to sharing the information between the layers. Physical to Transport layer information are shared in this protocol, due to this cross-layering is designed to optimize the power control. CLD using LOADPOWER (LOADPOW control protocol is reduce the overall end-end delay and the energy consumption using transmission power. The novelty of this work deals with both low and high transmission power control methodologies. So many power control schemes are dealt in MAC layer but this work, Power control protocol was done in network layer and it plays a vital role. A MAC approach to power control only does a local optimization whereas network layer is capable of global optimization. Simulation was done in NS-2 simulator with the performance metrics as improved throughput, energy consumption and end-end delay. The key concept is to improve the throughput, saves energy by sending all the packets with optimal transmission power according to the network load. A comparison of few protocols with Load Power Control Protocol (LPCP was implemented and got the better performances using NS-2 simulator.
Decision Model for Life Cycle Assessment of Power Transformer during Load Violation
S. S. Bhandari
2010-05-01
Full Text Available Utility have normally planned the power transformer based on its designed load demand for the long term. Due to unexpected penetration, the actual load profile does not always follow the designed load and load violation will occur at some points during the life cycle of the power transformer for which the utility is inevitably required to make strategic decision. In the past, the decisions were mainly focused on the technical condition of the assetwithout any consideration to investment budget limitation. In this paper, an alternative methodology comprising of knowledge based model, financial model and decision criteria is proposed to make an optimal decision during load violation. A generic power system similar to Nepal Electricity Authority’s context was utilized as a case study. The result depicts that this model can effectively assess the life cycle of power transformer balancing both the financialand technical constraints.
da Silva, Bruno Victor C; Simim, Mário A de Moura; Marocolo, Moacir; Franchini, Emerson; da Mota, Gustavo R
2015-06-01
We determined the optimal load for the peak power output (PPO) during the bench press throw (BPT) in Brazilian Jiu-Jitsu (BJJ) athletes and compared the PPO and maximal strength between advanced (AD) and nonadvanced (NA) athletes. Twenty-eight BJJ athletes (24.8 ± 5.7 years) performed the BPT at loads of 30, 40, 50, and 60% of their 1 repetition maximum (RM) in a randomized order (5-minute rest between BPTs). The PPO was determined by measuring the barbell displacement by an accelerometer (Myotest). The absolute (F = 7.25; p 0.05) in the PPO (30-60% 1RM). A polynomial adjustment indicated that the optimal load was ∼42% of 1RM for all groups and subgroups (R from 0.82 to 0.99). Our results suggest that there can be (1RM) differences between AD and NA BJJ athletes; however, there is no difference in the muscle power between the AD and NA groups. Additionally, ∼42% of 1RM seems to be the optimal load for developing maximal power using the BPT for the BJJ athletes.
Maximum Output Power Control Using Short-Circuit Current and Open-Circuit Voltage of a Solar Panel
Kato, Takahiro; Miyake, Takuma; Tashima, Daisuke; Sakoda, Tatsuya; Otsubo, Masahisa; Hombu, Mitsuyuki
2012-10-01
A control method to optimize the output power of a solar cell is necessary because the output of a solar cell strongly depends on solar radiation. We here proposed two output power control methods using the short-circuit current and open-circuit voltage of a solar panel. One of them used a current ratio and a voltage ratio (αβ control), and the other used a current ratio and a short-circuit current-electric power characteristic coefficient (αγ control). The usefulness of the αβ and the αγ control methods was evaluated. The results showed that the output power controlled by our proposed methods was close to the maximum output power of a solar panel.
Slip Development and Instability on a Heterogeneously Loaded Fault with Power-Law Slip-Weakening
Rice, J. R.; Uenishi, K.
2002-12-01
We consider slip initiation and rupture instability on planar faults that follow a non-linear slip-weakening relation and are subjected to a locally peaked loading stress, the level of which changes quasi-statically in time. For the case in which strength weakens linearly with slip, Uenishi and Rice [2002] (http://esag.harvard.edu/uenishi/research/nl/nl.html) have shown there exists a universal length of the slipping region at instability, independent of any length scales entering into the description of the shape of the loading stress distribution. Here we study slip development and its (in)stability for a power-law slip-weakening relation, giving fault strength as τ = τ p - Aδn where τ p is the peak strength at which slip initiates, δ is the slip, and A is a constant. Such a form with n ≈ 0.2-0.4 has been inferred, for slips from 1 to 500 mm, as an interpretation of seismological observations on the scaling of radiated energy with slip [Abercrombie and Rice, EOS, 2001; SCEC, 2002]. It is also consistent with laboratory experiments involving large rotary shear [Chambon et al., GRL, 2002]. We first employed an energy approach to give a Rayleigh-Ritz approximation for the dependence of slipping length and maximum slip on the level and shape of the loading stress distribution. That was done for a loading stress distribution τ p + Rt - κ x2 / 2 where x is distance along the fault, κ is a constant, and Rt is the stress change from that for which the peak in the loading stress distribution equals the strength τ p. Results show there is no longer a universal nucleation length, independent of κ , when n != 1, and that qualitative features of the slip development are significantly controlled by n. We also obtained full numerical solutions for the slip development. Remarkably, predictions of the simple energy approach are in reasonable quantitative agreement with them and give all qualitative features correctly. Principal results are as follows: If n > 2/3, the
Maximum at ALS: A powerful tool to investigate open problems in micro and optoelectronics
Lorusso, G.F.; Solak, H.; Singh, S.; Cerrina, F. [Univ. of Wisconsin, Madison, WI (United States). Center of X-ray Lithography; Batson, P.J.; Underwood, J.H. [Lawrence Berkeley National Lab., CA (United States). Center of X-ray Optics
1998-12-31
The authors present recent results obtained by MAXIMUM at the Advanced Light Source (ALS), at the Lawrence Berkeley National Laboratory. MAXIMUM is a scanning photoemission microscope, based on a multilayer coated Schwarzschild objective. An electron energy analyzer collects the emitted photoelectrons to form an image as the sample itself is scanned. The microscope has been purposely designed to take advantage of the high brightness of the third generation synchrotron radiation sources, and its installation at ALS has been recently completed. The spatial resolution of 100 nm and the spectral resolution of 200 meV make the instrument an extremely interesting tool to investigate current problems in opto- and microelectronics. In order to illustrate the potential of MAXIMUM in these fields, the authors report new results obtained by studying the electromigration in Al-Cu lines and the Al segregation in AlGaN thin films.
Power-law distribution functions derived from maximum entropy and a symmetry relationship
Peterson, G J
2011-01-01
Power-law distributions are common, particularly in social physics. Here, we explore whether power-laws might arise as a consequence of a general variational principle for stochastic processes. We describe communities of 'social particles', where the cost of adding a particle to the community is shared equally between the particle joining the cluster and the particles that are already members of the cluster. Power-law probability distributions of community sizes arise as a natural consequence of the maximization of entropy, subject to this 'equal cost sharing' rule. We also explore a generalization in which there is unequal sharing of the costs of joining a community. Distributions change smoothly from exponential to power-law as a function of a sharing-inequality quantity. This work gives an interpretation of power-law distributions in terms of shared costs.
A Novel Hybrid Method for Short-Term Power Load Forecasting
Huang Yuansheng
2016-01-01
Full Text Available Influenced by many uncertain and random factors, nonstationary, nonlinearity, and time-variety appear in power load series, which is difficult to forecast accurately. Aiming at locating these issues of power load forecasting, an innovative hybrid method is proposed to forecast power load in this paper. Firstly, ensemble empirical mode decomposition (EEMD is used to decompose the power load series into a series of independent intrinsic mode functions (IMFs and a residual term. Secondly, genetic algorithm (GA is then applied to determine the best weights of each IMF and the residual term named ensemble empirical mode decomposition based on weight (WEEMD. Thirdly, least square support vector machine (LSSVM and nonparametric generalized autoregressive conditional heteroscedasticity (NPGARCH are employed to forecast the subseries, respectively, based on the characteristics of power load series. Finally, the forecasted power load of each component is summed as the final forecasted result of power load. Compared with other methods, the forecasting results of this proposed model applied to the electricity market of Pennsylvania-New Jersey-Maryland (PJM indicate that the proposed model outperforms other models.
Zhang, Yiming; Zhao, Zhengming; Chen, Kainan; Fan, Jun
2017-05-01
Wireless Power Transfer (WPT) has been the research focus and applied in many fields. Normally power is transferred wirelessly to charge the battery, which requires specific load characteristics. The load characteristics are essential for the design and operation of the WPT system. This paper investigates the load characteristics of the WPT system with different resonant types and resonator numbers. It is found that in a WPT system with series or LCL resonance under a constant voltage source, the load characteristic is determined by the number of inductors. Even number of inductors results in a constant current characteristic and odd number constant voltage characteristic. Calculations, simulations, and experiments verify the analysis.
Measurements and Modelling of Base Station Power Consumption under Real Traffic Loads
Goran Petrovic
2012-03-01
Full Text Available Base stations represent the main contributor to the energy consumption of a mobile cellular network. Since traffic load in mobile networks significantly varies during a working or weekend day, it is important to quantify the influence of these variations on the base station power consumption. Therefore, this paper investigates changes in the instantaneous power consumption of GSM (Global System for Mobile Communications and UMTS (Universal Mobile Telecommunications System base stations according to their respective traffic load. The real data in terms of the power consumption and traffic load have been obtained from continuous measurements performed on a fully operated base station site. Measurements show the existence of a direct relationship between base station traffic load and power consumption. According to this relationship, we develop a linear power consumption model for base stations of both technologies. This paper also gives an overview of the most important concepts which are being proposed to make cellular networks more energy-efficient.
Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)
1997-11-25
Storage battery-aided load leveling system is introduced into a power system having a photovoltaic power generation (PV) system, and the effect of the introduction is examined. For this purpose, the resultant improvement on the load factor and reduction in the annual cost are evaluated. Used as the load factor in the studies are the hourly records of power transmitted and received by Chubu Electric Power Co., Inc., in 1995. The output of the PV system is calculated using weather data collected in Nagoya City in the same year. Findings as the result of the studies are stated below. The maximum power is suppressed but a little if it is only the PV system that is introduced into the system. That is, a 2GW PV system introduced into the system suppresses the maximum power only by 0.5GW or less. The maximum power is suppressed more effectively when a storage battery is added, and it decreases linearly with an increase in the storage battery capacity. As for reduction in the cost, the reducing effect is higher when the rate of storage battery capacity/introduced PV capacity is higher in the presence of an introduced PV capacity of 0.8GW or more. 2 refs., 7 figs., 3 tabs.
Abdelhak Dida
2015-02-01
Full Text Available This paper proposes a novel variable speed control algorithm for a grid connected doubly-fed induction generator (DFIG system. The main objective is to track the maximum power curve characteristic by using an adaptive fuzzy logic controller, and to compare it with the conventional optimal torque control method for large inertia wind turbines. The role of the FLC is to adapt the transfer function of the harvested mechanical power controller according to the operating point in variable wind speed. The control system has two sub-systems for the rotor side and the grid side converters (RSC, GSC. Active and reactive power control of the back-to-back converters has been achieved indirectly by controlling q-axis and d-axis current components. The main function of the RSC controllers is to track the maximum power through controlling the electromagnetic torque of the wind turbine. The GSC controls the DC-link voltage, and guarantees unity power factor between the GSC and the grid. The proposed system is developed and tested in MATLAB/SimPowerSystem (SPS environment.
Zhaoyong Mao
2016-01-01
Full Text Available This paper addresses the power generation control system of a new drag-type Vertical Axis Turbine with several retractable blades. The returning blades can be entirely hidden in the drum, and negative torques can then be considerably reduced as the drum shields the blades. Thus, the power efficiency increases. Regarding the control, a Linear Quadratic Tracking (LQT optimal control algorithm for Maximum Power Point Tracking (MPPT is proposed to ensure that the wave energy conversion system can operate highly effectively under fluctuating conditions and that the tracking process accelerates over time. Two-dimensional Computational Fluid Dynamics (CFD simulations are performed to obtain the maximum power points of the turbine’s output. To plot the tip speed ratio curve, the least squares method is employed. The efficacy of the steady and dynamic performance of the control strategy was verified using Matlab/Simulink software. These validation results show that the proposed system can compensate for power fluctuations and is effective in terms of power regulation.
Izumida, Yuki; Okuda, Koji
2014-05-01
We formulate the work output and efficiency for linear irreversible heat engines working between a finite-sized hot heat source and an infinite-sized cold heat reservoir until the total system reaches the final thermal equilibrium state with a uniform temperature. We prove that when the heat engines operate at the maximum power under the tight-coupling condition without heat leakage the work output is just half of the exergy, which is known as the maximum available work extracted from a heat source. As a consequence, the corresponding efficiency is also half of its quasistatic counterpart.
Vlachogiannis, Ioannis (John)
2009-01-01
A new formulation and solution of probabilistic constrained load flow (PCLF) problem suitable for modern power systems with wind power generation and electric vehicles (EV) demand or supply is represented. The developed stochastic model of EV demand/supply and the wind power generation model...
Pilot power optimization for AF relaying using maximum likelihood channel estimation
Wang, Kezhi
2014-09-01
Bit error rates (BERs) for amplify-and-forward (AF) relaying systems with two different pilot-symbol-aided channel estimation methods, disintegrated channel estimation (DCE) and cascaded channel estimation (CCE), are derived in Rayleigh fading channels. Based on these BERs, the pilot powers at the source and at the relay are optimized when their total transmitting powers are fixed. Numerical results show that the optimized system has a better performance than other conventional nonoptimized allocation systems. They also show that the optimal pilot power in variable gain is nearly the same as that in fixed gain for similar system settings. andcopy; 2014 IEEE.
Tofael Ahmed
2014-06-01
Full Text Available In this paper, a single phase doubly grounded semi-Z-source inverter with maximum power point tracking (MPPT is proposed for photovoltaic (PV systems. This proposed system utilizes a single-ended primary inductor (SEPIC converter as DC-DC converter to implement the MPPT algorithm for tracking the maximum power from a PV array and a single phase semi-Z-source inverter for integrating the PV with AC power utilities. The MPPT controller utilizes a fast-converging algorithm to track the maximum power point (MPP and the semi-Z-source inverter utilizes a nonlinear SPWM to produce sinusoidal voltage at the output. The proposed system is able to track the MPP of PV arrays and produce an AC voltage at its output by utilizing only three switches. Experimental results show that the fast-converging MPPT algorithm has fast tracking response with appreciable MPP efficiency. In addition, the inverter shows the minimization of common mode leakage current with its ground sharing feature and reduction of the THD as well as DC current components at the output during DC-AC conversion.
Wavelet time series MPARIMA modeling for power system short term load forecasting
冉启文; 单永正; 王建赜; 王骐
2003-01-01
The wavelet power system short term load forecasting(STLF) uses a mulriple periodical autoregressive integrated moving average(MPARIMA) model to model the mulriple near-periodicity, nonstationarity and nonlinearity existed in power system short term quarter-hour load time series, and can therefore accurately forecast the quarter-hour loads of weekdays and weekends, and provide more accurate results than the conventional techniques, such as artificial neural networks and autoregressive moving average(ARMA) models test results. Obtained with a power system networks in a city in Northeastern part of China confirm the validity of the approach proposed.
Self-regulating control of parasitic loads in a fuel cell power system
Vasquez, Arturo (Inventor)
2011-01-01
A fuel cell power system comprises an internal or self-regulating control of a system or device requiring a parasitic load. The internal or self-regulating control utilizes certain components and an interconnection scheme to produce a desirable, variable voltage potential (i.e., power) to a system or device requiring parasitic load in response to varying operating conditions or requirements of an external load that is connected to a primary fuel cell stack of the system. Other embodiments comprise a method of designing such a self-regulated control scheme and a method of operating such a fuel cell power system.
Power Control for Maximum Throughput in Spectrum Underlay Cognitive Radio Networks
Tadrous, John; Nafie, Mohammed; El-Keyi, Amr
2010-01-01
We investigate power allocation for users in a spectrum underlay cognitive network. Our objective is to find a power control scheme that allocates transmit power for both primary and secondary users so that the overall network throughput is maximized while maintaining the quality of service (QoS) of the primary users greater than a certain minimum limit. Since an optimum solution to our problem is computationally intractable, as the optimization problem is non-convex, we propose an iterative algorithm based on sequential geometric programming, that is proved to converge to at least a local optimum solution. We use the proposed algorithm to show how a spectrum underlay network would achieve higher throughput with secondary users operation than with primary users operating alone. Also, we show via simulations that the loss in primary throughput due to the admission of the secondary users is accompanied by a reduction in the total primary transmit power.
Design And Modeling An Automated Digsilent Power System For Optimal New Load Locations
Mohamed Saad
2015-08-01
Full Text Available Abstract The electric power utilities seek to take advantage of novel approaches to meet growing energy demand. Utilities are under pressure to evolve their classical topologies to increase the usage of distributed generation. Currently the electrical power engineers in many regions of the world are implementing manual methods to measure power consumption for farther assessment of voltage violation. Such process proved to be time consuming costly and inaccurate. Also demand response is a grid management technique where retail or wholesale customers are requested either electronically or manually to reduce their load. Therefore this paper aims to design and model an automated power system for optimal new load locations using DPL DIgSILENT Programming Language. This study is a diagnostic approach that assists system operator about any voltage violation cases that would happen during adding new load to the grid. The process of identifying the optimal bus bar location involves a complicated calculation of the power consumptions at each load bus As a result the DPL program would consider all the IEEE 30 bus internal networks data then a load flow simulation will be executed. To add the new load to the first bus in the network. Therefore the developed model will simulate the new load at each available bus bar in the network and generate three analytical reports for each case that captures the overunder voltage and the loading elements among the grid.
Maximum efficiency of steady-state heat engines at arbitrary power.
Ryabov, Artem; Holubec, Viktor
2016-05-01
We discuss the efficiency of a heat engine operating in a nonequilibrium steady state maintained by two heat reservoirs. Within the general framework of linear irreversible thermodynamics we derive a universal upper bound on the efficiency of the engine operating at arbitrary fixed power. Furthermore, we show that a slight decrease of the power below its maximal value can lead to a significant gain in efficiency. The presented analysis yields the exact expression for this gain and the corresponding upper bound.
Segui-Chilet, S.; Gimeno-Sales, F.J.; Orts, S.; Alcaniz, M.; Masot, R. [Instituto de Tecnologia Electrica - Grupo de Tecnologia Electronica, Universidad Politecnica de Valencia, Camino de Vera 14, 46022 Valencia (Spain); Garcera, G.; Figueres, E. [Departamento de Ingenieria Electronica, Universidad Politecnica de Valencia, Camino de Vera s/n, 46022 Valencia (Spain)
2007-09-15
This paper proposes a new definition of the unbalance power that allows the selective compensation of inefficiencies caused by linear loads by means of a three-phase shunt active power compensator (APC). Symmetrical components of current and voltage are used to evaluate the unbalance power in these systems and to define the compensating currents. The instantaneous power flows with unbalanced linear loads connected to a three-phase electrical system are analyzed following the normal procedure used for the quantification of the reactive power. Equations to calculate the unbalance power and the effective apparent power are obtained from the analysis of the instantaneous power flows. The output currents of the selective APC are defined using the instantaneous unbalance power approach. Power quantities and APC compensating current are defined for IEEE Std. 1459 and for the instantaneous unbalance power approach. Two examples are used to compare the power quantities and the APC operation. The main effects of unbalanced linear load and of fundamental voltage asymmetries are analyzed. Simulations of a shunt APC emphasize the advantages of the calculation of the compensating currents based on the proposed instantaneous unbalance power approach. A comparison with the results obtained by calculation of the compensating currents based on IEEE Std. 1459 is carried out. A new power factor is also defined and compared with other conventional definitions. (author)
Device Loading of Modular Multilevel Converter in Wind Power
Popova, L.; Ma, Ke; Blaabjerg, Frede
2015-01-01
on the gird conditions/requirements for wind power. The efficiency of the MMC under different P/Q boundaries defined by grid codes is investigated and compared with two-level (2L) and three-level (3L) neutral point clamped converters. It is concluded that it is possible to use the MMC in wind power...
Chao Peng
2015-01-01
Full Text Available A frequency control approach based on wind power and load power prediction information is proposed for wind-diesel-battery hybrid power system (WDBHPS. To maintain the frequency stability by wind power and diesel generation as much as possible, a fuzzy control theory based wind and diesel power control module is designed according to wind power and load prediction information. To compensate frequency fluctuation in real time and enhance system disturbance rejection ability, a battery energy storage system real-time control module is designed based on ADRC (active disturbance rejection control. The simulation experiment results demonstrate that the proposed approach has a better disturbance rejection ability and frequency control performance compared with the traditional droop control approach.
Wind farm electrical power production model for load flow analysis
Segura-Heras, Isidoro; Escriva-Escriva, Guillermo; Alcazar-Ortega, Manuel [Institute for Energy Engineering, Universidad Politecnica de Valencia, Camino de Vera, s/n, edificio 8E, escalera F, 2a planta, 46022 Valencia (Spain)
2011-03-15
The importance of renewable energy increases in activities relating to new forms of managing and operating electrical power: especially wind power. Wind generation is increasing its share in the electricity generation portfolios of many countries. Wind power production in Spain has doubled over the past four years and has reached 20 GW. One of the greatest problems facing wind farms is that the electrical power generated depends on the variable characteristics of the wind. To become competitive in a liberalized market, the reliability of wind energy must be guaranteed. Good local wind forecasts are therefore essential for the accurate prediction of generation levels for each moment of the day. This paper proposes an electrical power production model for wind farms based on a new method that produces correlated wind speeds for various wind farms. This method enables a reliable evaluation of the impact of new wind farms on the high-voltage distribution grid. (author)
Analysis of source-grid-load contribution to wind power accommodation
Li, Nan; Zhang, Jinfang; Zhang, Fuqiang
2017-01-01
In recent years, China’s wind power is developing rapidly, but wind electricity curtailment becomes a serious problem. This paper evaluates wind power penetration limit from peak regulation, analyses relevant technical elements that impact wind power accommodation, coving the source side, the transmission side and the load side. By taking certain measures around the three aspects, for example, reducing the minimum technical output of conventional units, increasing outbound transmission capacity, or increasing the valley load, wind electricity curtailment will be effectively reduced. This paper quantitatively analyses wind power penetration limit under certain conditions and the source-grid-load contribution to wind power accommodation, and explores the important technical factors that affect wind power accommodation.
Ye, Zhuo-Lin; Li, Wei-Sheng; Lai, Yi-Ming; He, Ji-Zhou; Wang, Jian-Hui
2015-12-01
We propose a quantum-mechanical Brayton engine model that works between two superposed states, employing a single particle confined in an arbitrary power-law trap as the working substance. Applying the superposition principle, we obtain the explicit expressions of the power and efficiency, and find that the efficiency at maximum power is bounded from above by the function: η+ = θ/(θ + 1), with θ being a potential-dependent exponent. Supported by the National Natural Science Foundation of China under Grant Nos. 11505091, 11265010, and 11365015, and the Jiangxi Provincial Natural Science Foundation under Grant No. 20132BAB212009
Timing A Pulsed Thin Film Pyroelectric Generator For Maximum Power Denisty
Smith, A. N.; Hanrahan, B. M.; Neville, C. J.; Jankowski, N. R.
2016-11-01
Pyroelectric thermal-to-electric energy conversion is accomplished by a cyclic process of thermally-inducing polarization changes in the material under an applied electric field. The pyroelectric MEMS device investigated consisted of a thin film PZT capacitor with platinum bottom and iridium oxide top electrodes. Electric fields between 1-20 kV/cm with a 30% duty cycle and frequencies from 0.1 - 100 Hz were tested with a modulated continuous wave IR laser with a duty cycle of 20% creating temperature swings from 0.15 - 26 °C on the pyroelectric receiver. The net output power of the device was highly sensitive to the phase delay between the laser power and the applied electric field. A thermal model was developed to predict and explain the power loss associated with finite charge and discharge times. Excellent agreement was achieved between the theoretical model and the experiment results for the measured power density versus phase delay. Limitations on the charging and discharging rates result in reduced power and lower efficiency due to a reduced net work per cycle.
Rafael Sabido
Full Text Available To compare the effect of 4-week unknown vs known loads strength training intervention on power output performance and throwing velocity in junior team handball players.Twenty-eight junior team-handball players (17.2 ± 0.6 years, 1.79 ± 0.07 m, 75.6 ± 9.4 kgwere divided into two groups (unknown loads: UL; known loads: KL. Both groups performed two sessions weekly consisting of four sets of six repetitions of the bench press throw exercise, using the 30%, 50% and 70% of subjects' individual 1 repetition maximum (1RM. In each set, two repetitions with each load were performed, but the order of the loads was randomised. In the KL group, researchers told the subjects the load to mobilise prior each repetition, while in the UL group, researchers did not provide any information. Maximal dynamic strength (1RM bench press, power output (with 30, 50 and 70% of 1RM and throwing velocity (7 m standing throw and 9 m jumping throw were assessed pre- and post-training intervention.Both UL and KL group improved similarly their 1RM bench press as well as mean and peak power with all loads. There were significant improvements in power developed in all the early time intervals measured (150 ms with the three loads (30, 50, 70% 1RM in the UL group, while KL only improved with 30% 1RM (all the time intervals and with 70% 1RM (at certain time intervals. Only the UL group improved throwing velocity in both standing (4.7% and jumping (5.3% throw (p > 0.05.The use of unknown loads has led to greater gains in power output in the early time intervals as well as to increases in throwing velocity compared with known loads. Therefore unknown loads are of significant practical use to increase both strength and in-field performance in a short period of training.
Optimization of a Turboprop UAV for Maximum Loiter and Specific Power Using Genetic Algorithm
Dinc, Ali
2016-09-01
In this study, a genuine code was developed for optimization of selected parameters of a turboprop engine for an unmanned aerial vehicle (UAV) by employing elitist genetic algorithm. First, preliminary sizing of a UAV and its turboprop engine was done, by the code in a given mission profile. Secondly, single and multi-objective optimization were done for selected engine parameters to maximize loiter duration of UAV or specific power of engine or both. In single objective optimization, as first case, UAV loiter time was improved with an increase of 17.5% from baseline in given boundaries or constraints of compressor pressure ratio and burner exit temperature. In second case, specific power was enhanced by 12.3% from baseline. In multi-objective optimization case, where previous two objectives are considered together, loiter time and specific power were increased by 14.2% and 9.7% from baseline respectively, for the same constraints.
Test report on the Abacus 30 kW bimode{reg_sign} inverter and maximum power tracker (MPT)
Bonn, R.; Ginn, J.; Zirzow, J. [and others
1995-06-01
Sandia National Laboratories conducts the photovoltaic balance of systems (BOS) program, which is sponsored by the US Department of Energy`s Office of Energy Management. Under this program, SNL lets commercialization contracts and conducts a laboratory program designed to advance BOS technology, improve BOS component reliability, and reduce the BOS life-cycle-cost. This report details the testing of the first large US manufactured hybrid inverter and its associated maximum power tracker.
Hwu, K. I.; Tu, W. C.; Wang, C.R.
2013-01-01
A photovoltaic energy conversion system, constructed by high step-up converter with hybrid maximum power point tracking (HMPPT), is presented. A voltage converter with a high voltage conversion ratio is proposed, which is simple in circuit and easy in control. After this, such a converter operating with a suitable initial duty cycle of the pulsewidth-modulated (PWM) control signal, together with the proposed HMPPT algorithm combining the fractional open-circuit voltage method and the incremen...
Test report on the Abacus 30 kW bimode(reg sign) inverter and Maximum Power Tracker (MPT)
Bonn, Russell; Ginn, Jerry; Zirzow, Jeff; Sittler, Greg
1995-06-01
Sandia National Laboratories conducts the photovoltaic balance of systems (BOS) program, which is sponsored by the US Department of Energy's Office of Energy Management. Under this program, SNL lets commercialization contracts and conducts a laboratory program designed to advance BOS technology, improve BOS component reliability, and reduce the BOS life-cycle-cost. This report details the testing of the first large US manufactured hybrid inverter and its associated maximum power tracker.
Ahteshamul Haque
2016-01-01
The energy crisis concern leads to look for alternate source of energy. Solar energy is considered as most reliable among the all renewable energy sources. Solar PV (Photovoltaic) is used to convert solar energy into electric energy. The efficiency of solar PV is very low and its characteristic is nonlinear. To overcome these drawbacks a technique known as maximum power point tracking is used. This algorithm is implemented in the control circuit of DC – DC converter. The objective...
Variants of Secondary Control with Power Recovery for Loading Hydraulic Driving Device
QI Xiaoye
2015-01-01
Current high power load simulators are generally incapable of obtalning both high loading performance and high energy efficiency. Simulators with high energy efficiency are used to simulate static-state load, and those with high dynamic performance typically have low energy efficiency. In this paper, the variants of secondary control (VSC) with power recovery are developed to solve this problem for loading hydraulic driving devices that operate under variable pressure, unlike classical secondary control (CSC) that operates in constant pressure network. Hydrostatic secondary control units are used as the loading components, by which the absorbed mechanical power from the tested device is converted into hydraulic power and then fed back into the tested system through 4 types of feedback passages (FPs). The loading subsystem can operate in constant pressure network, controlled variable pressure network, or the same variable pressure network as that of the tested device by using different FPs. The 4 types of systems are defined, and their key techniques are analyzed, including work principle, simulating the work state of original tested device, static operation points, loading performance, energy efficiency, and control strategy, etc. The important technical merits of the 4 schemes are compared, and 3 of the schemes are selected, designed, simulated using AMESim and evaluated. The researching results show that the investigated systems can simulate the given loads effectively, realize the work conditions of the tested device, and furthermore attaln a high power recovery efficiency that ranges from 0.54 to 0.85, even though the 3 schemes have different loading performances and energy efficiencies. This paper proposes several loading schemes that can achieve both high dynamic performance and high power recovery efficiency.
High efficiency WCDMA power amplifier with Pulsed Load Modulation (PLM) technique
Liao, Shu-Hsien
In wireless communication, high data rate complex modulation is used for spectral efficiency. However, power efficiency of power amplifier degrades when complex modulation is applied. Therefore, efficiency enhancement is necessary to maintain the performance. However, conventional efficiency enhancement schemes are nonlinear and performance improvement can only be optimized over a small range of power level. In order to preserve linearity and power efficiency, we propose a new digital power amplification technique "Pulsed Load Modulation (PLM)" for high efficiency and linear amplification. The PLM technique realizes load impedance modulation in digital fashion which is insensitive to device nonlinearity. Furthermore, the optimum power efficiency can be maintained over a wide range of output power. In this work, a PLM power amplifier module has been fabricated and to demonstrate the ability of PLM to provide high efficiency and linear amplification.
Ru-Min Chao
2016-01-01
Full Text Available This paper identifies the partial shading problem of a PV module using the one-diode model and simulating the characteristics exhibiting multiple-peak power output condition that is similar to a PV array. A modified particle swarm optimization (PSO algorithm based on the suggested search-agent deployment, retracking condition, and multicore operation is proposed in order to continuously locate the global maximum power point for the PV system. Partial shading simulation results for up to 16 modules in series/parallel formats are presented. A distributed PV system consisting of up to 8 a-silicon thin film PV panels and also having a dedicated DC/DC buck converter on each of the modules is tested. The converter reaches its steady state voltage output in 10 ms. However for MPPT operation, voltage, and current measurement interval is set to 20 ms to avoid unnecessary noise from the entire electric circuit. Based on the simulation and experiment results, each core of the proposed PSO operation should control no more than 4 PV modules in order to have the maximum tracking accuracy and minimum overall tracking time. Tracking for the global maximum power point of a distributed PV system under various partial shading conditions can be done within 1.3 seconds.
Suliang Ma
2016-11-01
Full Text Available Photovoltaic (PV systems have non-linear characteristics that generate maximum power at one particular operating point. Environmental factors such as irradiance and temperature variations greatly affect the maximum power point (MPP. Diverse offline and online techniques have been introduced for tracking the MPP. Here, to track the MPP, an augmented-state feedback linearized (AFL non-linear controller combined with an artificial neural network (ANN is proposed. This approach linearizes the non-linear characteristics in PV systems and DC/DC converters, for tracking and optimizing the PV system operation. It also reduces the dependency of the designed controller on linearized models, to provide global stability. A complete model of the PV system is simulated. The existing maximum power-point tracking (MPPT and DC/DC boost-converter controller techniques are compared with the proposed ANN method. Two case studies, which simulate realistic circumstances, are presented to demonstrate the effectiveness and superiority of the proposed method. The AFL with ANN controller can provide good dynamic operation, faster convergence speed, and fewer operating-point oscillations around the MPP. It also tracks the global maxima under different conditions, especially irradiance-mutating situations, more effectively than the conventional methods. Detailed mathematical models and a control approach for a three-phase grid-connected intelligent hybrid system are proposed using MATLAB/Simulink.
Intelligent power factor compensation equipment of three phase low voltage loads
无
2002-01-01
An intelligent power factor correction scheme is presented for three phase low power factor loads. This new scheme is able to perform individual phase sensing of parameters by monitoring at all times to sense a change in system parameters and affects individual phase correction by applying the exact amount of reactive components needed for each phase, and can also reduce negative sequence current caused by the load to improve system balance. An optimization criterion is used for the proper calculation of reactive power steps in a power compensation installation of capacitor banks. The criterion is enabled by sampling measurements performed on the electrical plant examined within specific interval of time.
Method for Load Sharing and Power Management in a Hybrid PV/Battery Source Islanded Microgrid
Karimi, Yaser; Oraee, Hashem; Guerrero, Josep M.
2016-01-01
This paper presents a decentralized load sharing and power management method for an islanded microgrid composed of PV units, battery units and hybrid PV/battery units. The proposed method performs all the necessary tasks such as load sharing among the units, battery charging and discharging and PV...
Plug and Process Loads Capacity and Power Requirements Analysis
Sheppy, M.; Gentile-Polese, L.
2014-09-01
This report addresses gaps in actionable knowledge that would help reduce the plug load capacities designed into buildings. Prospective building occupants and real estate brokers lack accurate references for plug and process load (PPL) capacity requirements, so they often request 5-10 W/ft2 in their lease agreements. Limited initial data, however, suggest that actual PPL densities in leased buildings are substantially lower. Overestimating PPL capacity leads designers to oversize electrical infrastructure and cooling systems. Better guidance will enable improved sizing and design of these systems, decrease upfront capital costs, and allow systems to operate more energy efficiently. The main focus of this report is to provide industry with reliable, objective third-party guidance to address the information gap in typical PPL densities for commercial building tenants. This could drive changes in negotiations about PPL energy demands.
Power System Structural Vulnerability Assessment based on an Improved Maximum Flow Approach
Fang, Jiakun; Su, Chi; Chen, Zhe
2017-01-01
to identify the critical lines in a system. The proposed method consists of two major steps. First, the power network is modeled as a graph with edges (transmission lines, transformers, etc.) and nodes (buses, substations, etc.). The critical scenarios are identified by using the principal component analysis...
Jui-Ho Chen
2014-03-01
Full Text Available This paper proposes a sliding mode extremum seeking control (SMESC of chaos embedded particle swarm optimization (CEPSO Algorithm, applied to the design of maximum power point tracking in wind power systems. Its features are that the control parameters in SMESC are optimized by CEPSO, making it unnecessary to change the output power of different wind turbines, the designed in-repetition rate is reduced, and the system control efficiency is increased. The wind power system control is designed by simulation, in comparison with the traditional wind power control method, and the simulated dynamic response obtained by the SMESC algorithm proposed in this paper is better than the traditional hill-climbing search (HCS and extremum seeking control (ESC algorithms in the transient or steady states, validating the advantages and practicability of the method proposed in this paper.
Electric Power Load Analysis (EPLA) for Surface Ships
2012-09-17
ESM can be based on a host of technologies to include batteries, flywheels , and ultra-capacitors. Energy storage can be provided for use in a...electrical generation, energy storage , and power conversion components and equipment and current requirements for electrical distribution equipment and...Demand factor 4 3.7 Demand power 4 3.8 Electric and propulsion plant concept of operations 4 3.9 Emergency ship control 4 3.10 Energy storage
Controller design for a Wind Farm, Considering both Power and Load Aspects
Soleimanzadeh, Maryam; Wisniewski, Rafal
2011-01-01
turbine. The control algorithm determines the reference signals for each individual wind turbine controller in two scenarios based on low and high wind speed. In low wind speed, the reference signals for rotor speed are adjusted, taking the trade-off between power maximization and load minimization....... Moreover, the controller has been proven exceptionally useful in solving the problem of both power and load optimization on the basis of this model....
Error detection in core loading in the condition of asymmetrical distribution of power
Ryzhov, Andrei; Pinegin, Anatoly [National Research Centre ' Kurchatov Institute' , Moscow (Russian Federation)
2016-09-15
The error detection in core loading in many cases happens in conditions of a significant asymmetry in the distribution of power density, which is caused by thermal mechanical deformations of reactor core, and temperature differences in the cold legs of coolant. The asymmetry of power distribution essentially decreases the effectiveness of algorithms used to detect errors in the core loading using ICIS data. The paper proposes the ways for solving this problem by means of special filtration algorithms.
de Rooij, Michael Andrew; Steigerwald, Robert Louis; Delgado, Eladio Clemente
2008-12-16
Photovoltaic power converter system including a controller configured to reduce load harmonics is provided. The system comprises a photovoltaic array and an inverter electrically coupled to the array to generate an output current for energizing a load connected to the inverter and to a mains grid supply voltage. The system further comprises a controller including a first circuit coupled to receive a load current to measure a harmonic current in the load current. The controller includes a second circuit to generate a fundamental reference drawn by the load. The controller further includes a third circuit for combining the measured harmonic current and the fundamental reference to generate a command output signal for generating the output current for energizing the load connected to the inverter. The photovoltaic system may be configured to compensate harmonic currents that may be drawn by the load.
Santos-Silva, Paulo Roberto; Fonseca, Alfredo José; Castro, Anita Weigand de; Greve, Júlia Maria D'Andréa; Hernandez, Arnaldo José
2007-08-01
To determine the degree of reproducibility of maximum oxygen consumption (VO2max) among soccer players, using a modified Heck protocol. 2 evaluations with an interval of 15 days between them were performed on 11 male soccer players. All the players were at a high performance level; they were training for an average of 10 hours per week, totaling 5 times a week. When they were evaluated, they were in the middle of the competitive season, playing 1 match per week. The soccer players were evaluated on an ergometric treadmill with velocity increments of 1.2 km.h-1 every 2 minutes and a fixed inclination of 3% during the test. VO2max was measured directly using a breath-by-breath metabolic gas analyzer. The maximum running speed and VO2max attained in the 2 tests were, respectively: (15.6 +/- 1.1 vs. 15.7 +/- 1.2 km.h-1; [P = .78]) and (54.5 +/- 3.9 vs. 55.2 +/- 4.4 ml.kg-1.min-1; [P = .88]). There was high and significant correlation of VO2max between the 2 tests with a 15-day interval between them [r = 0.97; P testing was insufficient to significantly modify the soccer players' VO2max values.
Optimization of hybrid power system composed of SMES and flywheel MG for large pulsed load
Niiyama, K.; Yagai, T.; Tsuda, M.; Hamajima, T.
2008-09-01
A superconducting magnetic storage system (SMES) has some advantages such as rapid large power response and high storage efficiency which are superior to other energy storage systems. A flywheel motor generator (FWMG) has large scaled capacity and high reliability, and hence is broadly utilized for a large pulsed load, while it has comparatively low storage efficiency due to high mechanical loss compared with SMES. A fusion power plant such as International Thermo-Nuclear Experimental Reactor (ITER) requires a large and long pulsed load which causes a frequency deviation in a utility power system. In order to keep the frequency within an allowable deviation, we propose a hybrid power system for the pulsed load, which equips the SMES and the FWMG with the utility power system. We evaluate installation cost and frequency control performance of three power systems combined with energy storage devices; (i) SMES with the utility power, (ii) FWMG with the utility power, (iii) both SMES and FWMG with the utility power. The first power system has excellent frequency power control performance but its installation cost is high. The second system has inferior frequency control performance but its installation cost is the lowest. The third system has good frequency control performance and its installation cost is attained lower than the first power system by adjusting the ratio between SMES and FWMG.
Aragon-Gonzalez, G; Leon-Galicia, A; Morales-Gomez, J R
2007-01-01
In this work we include, for the Carnot cycle, irreversibilities of linear finite rate of heat transferences between the heat engine and its reservoirs, heat leak between the reservoirs and internal dissipations of the working fluid. A first optimization of the power output, the efficiency and ecological function of an irreversible Carnot cycle, with respect to: internal temperature ratio, time ratio for the heat exchange and the allocation ratio of the heat exchangers; is performed. For the second and third optimizations, the optimum values for the time ratio and internal temperature ratio are substituted into the equation of power and, then, the optimizations with respect to the cost and effectiveness ratio of the heat exchangers are performed. Finally, a criterion of partial optimization for the class of irreversible Carnot engines is herein presented.
Quantum Coherent Three-Terminal Thermoelectrics: Maximum Efficiency at Given Power Output
Robert S. Whitney
2016-05-01
Full Text Available This work considers the nonlinear scattering theory for three-terminal thermoelectric devices used for power generation or refrigeration. Such systems are quantum phase-coherent versions of a thermocouple, and the theory applies to systems in which interactions can be treated at a mean-field level. It considers an arbitrary three-terminal system in any external magnetic field, including systems with broken time-reversal symmetry, such as chiral thermoelectrics, as well as systems in which the magnetic field plays no role. It is shown that the upper bound on efficiency at given power output is of quantum origin and is stricter than Carnot’s bound. The bound is exactly the same as previously found for two-terminal devices and can be achieved by three-terminal systems with or without broken time-reversal symmetry, i.e., chiral and non-chiral thermoelectrics.
Maximum Efficiency of Thermoelectric Heat Conversion in High-Temperature Power Devices
V. I. Khvesyuk
2016-01-01
Full Text Available Modern trends in development of aircraft engineering go with development of vehicles of the fifth generation. The features of aircrafts of the fifth generation are motivation to use new high-performance systems of onboard power supply. The operating temperature of the outer walls of engines is of 800–1000 K. This corresponds to radiation heat flux of 10 kW/m2 . The thermal energy including radiation of the engine wall may potentially be converted into electricity. The main objective of this paper is to analyze if it is possible to use a high efficiency thermoelectric conversion of heat into electricity. The paper considers issues such as working processes, choice of materials, and optimization of thermoelectric conversion. It presents the analysis results of operating conditions of thermoelectric generator (TEG used in advanced hightemperature power devices. A high-temperature heat source is a favorable factor for the thermoelectric conversion of heat. It is shown that for existing thermoelectric materials a theoretical conversion efficiency can reach the level of 15–20% at temperatures up to 1500 K and available values of Ioffe parameter being ZT = 2–3 (Z is figure of merit, T is temperature. To ensure temperature regime and high efficiency thermoelectric conversion simultaneously it is necessary to have a certain match between TEG power, temperature of hot and cold surfaces, and heat transfer coefficient of the cooling system. The paper discusses a concept of radiation absorber on the TEG hot surface. The analysis has demonstrated a number of potentialities for highly efficient conversion through using the TEG in high-temperature power devices. This work has been implemented under support of the Ministry of Education and Science of the Russian Federation; project No. 1145 (the programme “Organization of Research Engineering Activities”.
Research on improvement of power quality of Micro - grid based on SVG pulse load
Lv, Chuang; Xie, Pu
2017-05-01
Pulse load will make the micro-grid public bus power to produce a high peak pulse due to its cyclical pulsation characteristics,, and make the micro-grid voltage fluctuations, frequency fluctuations, voltage and current distortion, power factor reduction and other adverse effects. In order to suppress the adverse effects of the pulse load on the microgrid and improve the power quality of the microgrid, this paper established the SVG simulation model in Matlab / Simulink environment, the superiority of SVG is verified by comparing the improvement of power quality before and after adding the SVG to microgrid system. The results show that the SVG model can suppress the adverse effects effectively of the pulse load on the microgrid, which is of great value and significance to the reactive power compensation and harmonic suppression of the microgrid.
A FAST BIT-LOADING ALGORITHM FOR HIGH SPEED POWER LINE COMMUNICATIONS
Zhang Shengqing; Zhao Li; Zou Cairong
2012-01-01
Adaptive bit-loading is a key technology in high speed power line communications with the Orthogonal Frequency Division Multiplexing (OFDM) modulation technology.According to the real situation of the transmitting power spectrum limited in high speed power line communications,this paper explored the adaptive bit loading algorithm to maximize transmission bit number when transmitting power spectral density and bit error rate are not exceed upper limit.With the characteristics of the power line channel,first of all,it obtains the optimal bit loading algorithm,and then provides the improved algorithm to reduce the computational complexity.Based on the analysis and simulation,it offers a non-iterative bit allocation algorithm,and finally the simulation shows that this new algorithm can greatly reduce the computational complexity,and the actual bit allocation results close to optimal.
Effect of unloading and loading on power in simulated countermovement and squat jumps.
Bobbert, Maarten F
2014-06-01
In the literature, substantial decreases in power output in jumping have been described for both unloading and loading, and these have been attributed to the intrinsic force-velocity-power relationship of muscle. The purpose of this study was to gain a solid understanding of how and why unloading and loading affect power output during jumping. Vertical jumps were simulated with a model of the musculoskeletal system, consisting of four rigid segments actuated by six muscles. Muscle stimulation over time was optimized to ensure maximal performance in each loading condition. It was found that, in contrast to what is reported in the literature, unloading by an extra vertical force of -60% of body weight caused a small increase in the peak of the rate of change of the effective energy of the center of mass (dEeff/dt). Loading by an extra vertical force of +60% of body weight caused a decrease in peak dEeff/dt, but this decrease was much smaller than that described in the literature. The small variations in peak dEeff/dt among loading conditions in the simulated jumps were only in part due to the intrinsic force-velocity-power relationship of muscle. Why did the effects of unloading and loading in the simulation model deviate from effects reported in subjects? One possible explanation is that subjects tend to make a smaller countermovement when loaded; in the simulation model, making a smaller countermovement caused a major reduction in peak dEeff/dt. A second possible explanation is that subjects cannot quickly optimize their control and therefore produce submaximal power output in unfamiliar loading conditions. The effects of unloading and loading are due only in part to the intrinsic force-velocity-power relationship of muscle.
Electronic stopping power of hydrogen in KCl at the stopping maximum and at very low energies
Primetzhofer, D.; Markin, S. N.; Bauer, P.
2011-10-01
The electronic energy loss of hydrogen ions in KCl was investigated in a wide energy range. Thin films of KCl were evaporated on an Au/Si substrate. Rutherford Backscattering Spectrometry (RBS) was performed with protons and deuterons at energies from 30 to 400 keV/nucleon. At lower energies experiments were performed by Time-Of-Flight Low energy ion scattering (TOF-LEIS) again with proton and deuteron projectiles. Experimental results are compared to calculated/tabulated values for the electronic energy loss. Whereas at energies beyond the stopping maximum very good agreement is found, at lower ion energies discrepancies between experiment and calculations increase. At very low ion velocities the extrapolated stopping cross section ɛ predicts vanishing electronic energy loss at energies below 100 eV/nucleon.
Transistor-based filter for inhibiting load noise from entering a power supply
Taubman, Matthew S
2013-07-02
A transistor-based filter for inhibiting load noise from entering a power supply is disclosed. The filter includes a first transistor having an emitter coupled to a power supply, a collector coupled to a load, and a base. The filter also includes a first capacitor coupled between the base of the first transistor and a ground terminal. The filter further includes an impedance coupled between the base and a node between the collector and the load, or a second transistor and second capacitor. The impedance can be a resistor or an inductor.
B. M. Khroustalev
2010-01-01
Full Text Available The paper considers a possibility to use co-generated complexes having heat technological industrial load for operation in accordance with the requirements of irregularity of electric power generation schedule.
NSGIC State | GIS Inventory — Environmental Modeling dataset current as of 1999. Florida Adopted TMDLs. What is a TMDL (Total Maximum Daily Load)? A scientific determination of the maximum amount...
Ferrite Loaded Coils for Improved Wireless Power Transfer Efficiency
2015-09-01
Department of Defense or the U.S. Government. IRB Protocol number ____N/A____. 12a. DISTRIBUTION / AVAILABILITY STATEMENT Approved for public...Series on Innovative Wireless Power Transmission: Technologies, Systems, and Applications, Kyoto , Japan, 2011, pp. 73–76. [15] Z. Ullah, A. Shahid, and
杨忠炯; 何清华; 柳波
2004-01-01
Using hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle as a simulation example, the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle were simulated and discussed with SIMULINK software and hydraulic control theory. The results show that the dynamic characteristics of hydraulic power steering system are improved obviously by using bladder accumulator, the hydraulic power steering system of model EIMCO 922 load-haul-dump vehicle generates vibration at the initial stage under the normal steering condition of pulse input, and its static response time is 0.25 s shorter than that without bladder accumulator. Under the normal steering working condition, the capacity of steering accumulator for absorbing pulse is directly proportional to the cross section area of connecting pipeline, and inversely proportional to the length of connecting pipeline. At the same time, the precharge pressure of nitrogen in steering accumulator should be 60%- 80% of the rated minimum working pressure of hydraulic power steering system. Under the abnormal steering working condition, the steering cylinder piston may obtain higher motion velocity, and the dynamic response velocity of hydraulic power steering system can be increased by reducing the pressure drop of hydraulic pipelines between the accumulator and steering cylinder and by increasing the rated pressure of hydraulic power steering system, but the dynamic characteristics of hydraulic power steering system in load-haul-dump vehicle have nothing to do with the precharge pressure of nitrogen in steering accumulator.
A High-Efficiency 4x45W Car Audio Power Amplifier using Load Current Sharing
Mensink, C.H.J.; Mensink, C.; van Tuijl, Adrianus Johannes Maria; Gierkink, Sander L.J.; Mostert, F.; van der Zee, Ronan A.R.
2010-01-01
A 4x45W (EIAJ) monolithic car audio power amplifier is presented that achieves a power dissipation decrease of nearly 2x over standard class AB operation by sharing load currents between loudspeakers. Output signals are conditioned using a common-mode control loop to allow switch placement between l
A High-Efficiency 4x45W Car Audio Power Amplifier using Load Current Sharing
Mensink, C.H.J.; Mensink, C.; van Tuijl, Adrianus Johannes Maria; Gierkink, Sander L.J.; Mostert, F.; van der Zee, Ronan A.R.
2010-01-01
A 4x45W (EIAJ) monolithic car audio power amplifier is presented that achieves a power dissipation decrease of nearly 2x over standard class AB operation by sharing load currents between loudspeakers. Output signals are conditioned using a common-mode control loop to allow switch placement between
Electronic system for high power load control. [solar arrays
Miller, E. L. (Inventor)
1980-01-01
Parallel current paths are divided into two groups, with control devices in the current paths of one group each having a current limiting resistor, and the control devices in the other group each having no limiting resistor, so that when the control devices of the second group are turned fully on, a short circuit is achieved by the arrangement of parallel current paths. Separate but coordinated control signals are provided to turn on the control devices of the first group and increase their conduction toward saturation as a function of control input, and when fully on, or shortly before, to turn on the control devices of the second group and increase their conduction toward saturation as a function of the control input as that input continues to increase. Electronic means may be used to generate signals. The system may be used for 1-V characteristic measurements of solar arrays as well as for other load control purposes.
An improved harmony search algorithm for power economic load dispatch
Coelho, Leandro dos Santos [Pontifical Catholic Univ. of Parana, PUCPR, Industrial and Systems Engineering Graduate Program, PPGEPS, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil); Mariani, Viviana Cocco [Pontifical Catholic Univ. of Parana, PUCPR, Dept. of Mechanical Engineering, PPGEM, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)
2009-10-15
A meta-heuristic algorithm called harmony search (HS), mimicking the improvisation process of music players, has been recently developed. The HS algorithm has been successful in several optimization problems. The HS algorithm does not require derivative information and uses stochastic random search instead of a gradient search. In addition, the HS algorithm is simple in concept, few in parameters, and easy in implementation. This paper presents an improved harmony search (IHS) algorithm based on exponential distribution for solving economic dispatch problems. A 13-unit test system with incremental fuel cost function taking into account the valve-point loading effects is used to illustrate the effectiveness of the proposed IHS method. Numerical results show that the IHS method has good convergence property. Furthermore, the generation costs of the IHS method are lower than those of the classical HS and other optimization algorithms reported in recent literature. (author)
An improved harmony search algorithm for power economic load dispatch
Santos Coelho, Leandro dos [Pontifical Catholic University of Parana, PUCPR, Industrial and Systems Engineering Graduate Program, PPGEPS, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)], E-mail: leandro.coelho@pucpr.br; Mariani, Viviana Cocco [Pontifical Catholic University of Parana, PUCPR, Department of Mechanical Engineering, PPGEM, Imaculada Conceicao, 1155, 80215-901 Curitiba, PR (Brazil)], E-mail: viviana.mariani@pucpr.br
2009-10-15
A meta-heuristic algorithm called harmony search (HS), mimicking the improvisation process of music players, has been recently developed. The HS algorithm has been successful in several optimization problems. The HS algorithm does not require derivative information and uses stochastic random search instead of a gradient search. In addition, the HS algorithm is simple in concept, few in parameters, and easy in implementation. This paper presents an improved harmony search (IHS) algorithm based on exponential distribution for solving economic dispatch problems. A 13-unit test system with incremental fuel cost function taking into account the valve-point loading effects is used to illustrate the effectiveness of the proposed IHS method. Numerical results show that the IHS method has good convergence property. Furthermore, the generation costs of the IHS method are lower than those of the classical HS and other optimization algorithms reported in recent literature.
Wei, J.; Lefeuvre, E.; Mathias, H.; Costa, F.
2016-12-01
The operation analysis of a new interface circuit for electrostatic vibration energy harvesting with adjustable bias voltage is carried out in this paper. Two configurations determined by the open or closed states of an electronic switch are examined. The increase of the voltage across a biasing capacitor, occurring when the switch is open, is proved theoretically and experimentally. With the decrease of this biasing voltage which occurs naturally when the switch is closed due to imperfections of the circuit, the bias voltage can be maintained close to a target value by appropriate ON and OFF control of the switch. As the energy converted by the variable capacitor on each cycle depends on the bias voltage, this energy can be therefore accurately controlled. This feature opens up promising perspectives for optimization the power harvested by electrostatic devices. Simulation results with and without electromechanical coupling effect are presented. In experimental tests, a simple switch control enabling to stabilize the bias voltage is described.
Cascade failure analysis of power grid using new load distribution law and node removal rule
Ren, Hai-Peng; Song, Jihong; Yang, Rong; Baptista, Murilo S.; Grebogi, Celso
2016-01-01
The power grid is a directional complex network of generators, substations, and consumers. We propose a new load distribution law to emulate the power grid. We assume that the power flow is transferred through all the paths connecting generators and consumers according to their efficiency. The initial generation of generators and the initial loads of substations are calculated according to the path efficiency and the load of the consumers. If a node fails, it is removed from the power grid, and all paths passing through it will fail to transfer power. In that case, the loads of the corresponding consumers are redistributed within the whole network. During the failure cascading and propagation procedure, our node removal rule is to remove the first overload node along the opposite direction of power flow, then the network distributes load and goes on the cascade procedure. Our new removal rule for nodes does suppress the large scale cascading failures. This work would be very helpful for designing the protective relay system and the tolerant parameters of the grid.
LU Zhi-Gang; GONG Yu-Bin; GAI Wei; GAO Peng; GAO Feng; WEI Yan- Yu; WANG Wen-Xiang
2009-01-01
We report on experimental test of a 7.8 GHz power extractor using a dielectric loaded rectangular waveguide structure. This work is conducted at the Argonne wakefield accelerator (AWA) facility. The wakefield is excited by an electron beam travelling through a dielectric loaded rectangular waveguide, and the generated rf power is then subsequently extracted with a properly designed rf coupler. In the experiment, 30 MW of output power is excited by a 66nC single electron bunch, and wakefield superposition by a train consisting of four bunches is also demonstrated. Both the results agree well with theoretical predictions.
Maximum power point tracking for photovoltaic applications by using two-level DC/DC boost converter
Moamaei, Parvin
Recently, photovoltaic (PV) generation is becoming increasingly popular in industrial applications. As a renewable and alternative source of energy they feature superior characteristics such as being clean and silent along with less maintenance problems compared to other sources of the energy. In PV generation, employing a Maximum Power Point Tracking (MPPT) method is essential to obtain the maximum available solar energy. Among several proposed MPPT techniques, the Perturbation and Observation (P&O;) and Model Predictive Control (MPC) methods are adopted in this work. The components of the MPPT control system which are P&O; and MPC algorithms, PV module and high gain DC-DC boost converter are simulated in MATLAB Simulink. They are evaluated theoretically under rapidly and slowly changing of solar irradiation and temperature and their performance is shown by the simulation results, finally a comprehensive comparison is presented.
S. Saravanan
2014-01-01
Full Text Available This paper proposes a new power conditioner topology with an intelligent power management controller that integrates multiple renewable energy sources such as solar energy, wind energy, and fuel cell energy with battery and AC grid supply as backup to make the best use of their operating characteristics with better reliability than that could be obtained by single renewable energy source based power supply. The proposed embedded controller is programmed to perform MPPT for solar PV panel and WTG, SOC estimation and battery, maintaining a constant voltage at PCC and power flow control by regulating the reference currents of the controller in an instantaneous basis. The instantaneous variation in reference currents of the controller enhances the controller response as it accommodates the effect of continuously varying solar insolation and wind speed in the power management. It also prioritizes the sources for consumption to achieve maximum usage of green energy than grid energy. The simulation results of the proposed power management system with real-time solar radiation and wind velocity data collected from solar centre, KEC, and experimental results for a sporadically varying load demand are presented in this paper and the results are encouraging from reliability and stability perspectives.
Rounds, Stewart A.; Sullivan, Annett B.
2013-01-01
Flow and water-quality models are being used to support the development of Total Maximum Daily Load (TMDL) plans for the Klamath River downstream of Upper Klamath Lake (UKL) in south-central Oregon. For riverine reaches, the RMA-2 and RMA-11 models were used, whereas the CE-QUAL-W2 model was used to simulate pooled reaches. The U.S. Geological Survey (USGS) was asked to review the most upstream of these models, from Link River Dam at the outlet of UKL downstream through the first pooled reach of the Klamath River from Lake Ewauna to Keno Dam. Previous versions of these models were reviewed in 2009 by USGS. Since that time, important revisions were made to correct several problems and address other issues. This review documents an assessment of the revised models, with emphasis on the model revisions and any remaining issues. The primary focus of this review is the 19.7-mile Lake Ewauna to Keno Dam reach of the Klamath River that was simulated with the CE-QUAL-W2 model. Water spends far more time in the Lake Ewauna to Keno Dam reach than in the 1-mile Link River reach that connects UKL to the Klamath River, and most of the critical reactions affecting water quality upstream of Keno Dam occur in that pooled reach. This model review includes assessments of years 2000 and 2002 current conditions scenarios, which were used to calibrate the model, as well as a natural conditions scenario that was used as the reference condition for the TMDL and was based on the 2000 flow conditions. The natural conditions scenario included the removal of Keno Dam, restoration of the Keno reef (a shallow spot that was removed when the dam was built), removal of all point-source inputs, and derivation of upstream boundary water-quality inputs from a previously developed UKL TMDL model. This review examined the details of the models, including model algorithms, parameter values, and boundary conditions; the review did not assess the draft Klamath River TMDL or the TMDL allocations
Real-Time Load-Side Control of Electric Power Systems
Zhao, Changhong
Two trends are emerging from modern electric power systems: the growth of renewable (e.g., solar and wind) generation, and the integration of information technologies and advanced power electronics. The former introduces large, rapid, and random fluctuations in power supply, demand, frequency, and voltage, which become a major challenge for real-time operation of power systems. The latter creates a tremendous number of controllable intelligent endpoints such as smart buildings and appliances, electric vehicles, energy storage devices, and power electronic devices that can sense, compute, communicate, and actuate. Most of these endpoints are distributed on the load side of power systems, in contrast to traditional control resources such as centralized bulk generators. This thesis focuses on controlling power systems in real time, using these load side resources. Specifically, it studies two problems. (1) Distributed load-side frequency control: We establish a mathematical framework to design distributed frequency control algorithms for flexible electric loads. In this framework, we formulate a category of optimization problems, called optimal load control (OLC), to incorporate the goals of frequency control, such as balancing power supply and demand, restoring frequency to its nominal value, restoring inter-area power flows, etc., in a way that minimizes total disutility for the loads to participate in frequency control by deviating from their nominal power usage. By exploiting distributed algorithms to solve OLC and analyzing convergence of these algorithms, we design distributed load-side controllers and prove stability of closed-loop power systems governed by these controllers. This general framework is adapted and applied to different types of power systems described by different models, or to achieve different levels of control goals under different operation scenarios. We first consider a dynamically coherent power system which can be equivalently modeled with
Dual-Axis Solar Tracking System for Maximum Power Production in PV Systems
Muhd.Ikram Mohd. Rashid
2015-12-01
Full Text Available The power developed in a solar energy system depends fundamentally upon the amount of sunlight captured by the photovoltaic modules/arrays. This paper describes a simple electro-mechanical dual axis solar tracking system designed and developed in a study. The control of the two axes was achieved by the pulses generated from the data acquisition (DAQ card fed into four relays. This approach was so chosen to effectively avoid the error that usually arises in sensor-based methods. The programming of the mathematical models of the solar elevation and azimuth angles was done using Borland C++ Builder. The performance and accuracy of the developed system was evaluated with a PV panel at latitude 3.53o N and longitude 103.5o W in Malaysia. The results obtained reflect the effectiveness of the developed tracking system in terms of the energy yield when compared with that generated from a fixed panel. Overall, 20%, 23% and 21% additional energy were produced for the months of March, April and May respectively using the tracker developed in this study.
The History and Perspectives of Efficiency at Maximum Power of the Carnot Engine
Michel Feidt
2017-07-01
Full Text Available Finite Time Thermodynamics is generally associated with the Curzon–Ahlborn approach to the Carnot cycle. Recently, previous publications on the subject were discovered, which prove that the history of Finite Time Thermodynamics started more than sixty years before even the work of Chambadal and Novikov (1957. The paper proposes a careful examination of the similarities and differences between these pioneering works and the consequences they had on the works that followed. The modelling of the Carnot engine was carried out in three steps, namely (1 modelling with time durations of the isothermal processes, as done by Curzon and Ahlborn; (2 modelling at a steady-state operation regime for which the time does not appear explicitly; and (3 modelling of transient conditions which requires the time to appear explicitly. Whatever the method of modelling used, the subsequent optimization appears to be related to specific physical dimensions. The main goal of the methodology is to choose the objective function, which here is the power, and to define the associated constraints. We propose a specific approach, focusing on the main functions that respond to engineering requirements. The study of the Carnot engine illustrates the synthesis carried out and proves that the primary interest for an engineer is mainly connected to what we called Finite (physical Dimensions Optimal Thermodynamics, including time in the case of transient modelling.
Zhu, Meiling; Worthington, Emma; Njuguna, James
2009-07-01
This paper presents, for the first time, a coupled piezoelectric-circuit finite element model (CPC-FEM) to analyze the power output of a vibration-based piezoelectric energy-harvesting device (EHD) when it is connected to a load resistor. Special focus is given to the effect of the load resistor value on the vibrational amplitude of the piezoelectric EHD, and thus on the current, voltage, and power generated by the device, which are normally assumed to be independent of the load resistor value to reduce the complexity of modeling and simulation. The presented CPC-FEM uses a cantilever with a sandwich structure and a seismic mass attached to the tip to study the following characteristics of the EHD as a result of changing the load resistor value: 1) the electric outputs: the current through and voltage across the load resistor; 2) the power dissipated by the load resistor; 3) the displacement amplitude of the tip of the cantilever; and 4) the shift in the resonant frequency of the device. It is found that these characteristics of the EHD have a significant dependence on the load resistor value, rather than being independent of it as is assumed in most literature. The CPC-FEM is capable of predicting the generated output power of the EHD with different load resistor values while simultaneously calculating the effect of the load resistor value on the displacement amplitude of the tip of the cantilever. This makes the CPC-FEM invaluable for validating the performance of a designed EHD before it is fabricated and tested, thereby reducing the recurring costs associated with repeat fabrication and trials. In addition, the proposed CPC-FEM can also be used for producing an optimized design for maximum power output.
Linlin Tan
2016-10-01
Full Text Available An opportunity wireless charging system for electric vehicles when they stop and wait at traffic lights is proposed in this paper. In order to solve the serious power fluctuation caused by random access loads, this study presents a power stabilization strategy based on counting the number of electric vehicles in a designated area, including counting method, power source voltage adjustment strategy and choice of counting points. Firstly, the circuit model of a wireless power system with multi-loads is built and the equation of each load is obtained. Secondly, after the counting method of electric vehicles is stated, the voltage adjustment strategy, based on the number of electric vehicles when the system is at a steady state, is set out. Then, the counting points are chosen according to power curves when the voltage adjustment strategy is adopted. Finally, an experimental prototype is implemented to verify the power stabilization strategy. The experimental results show that, with the application of this strategy, the charging power is stabilized with the fluctuation of no more than 5% when loads access randomly.
Tom, Nathan M.; Yu, Yi-Hsiang; Wright, Alan D.; Lawson, Michael
2016-06-24
The aim of this paper is to describe how to control the power-to-load ratio of a novel wave energy converter (WEC) in irregular waves. The novel WEC that is being developed at the National Renewable Energy Laboratory combines an oscillating surge wave energy converter (OSWEC) with control surfaces as part of the structure; however, this work only considers one fixed geometric configuration. This work extends the optimal control problem so as to not solely maximize the time-averaged power, but to also consider the power-take-off (PTO) torque and foundation forces that arise because of WEC motion. The objective function of the controller will include competing terms that force the controller to balance power capture with structural loading. Separate penalty weights were placed on the surge-foundation force and PTO torque magnitude, which allows the controller to be tuned to emphasize either power absorption or load shedding. Results of this study found that, with proper selection of penalty weights, gains in time-averaged power would exceed the gains in structural loading while minimizing the reactive power requirement.
Lei Jiang
2012-01-01
Full Text Available Energy signature analysis of power appliance is the core of nonintrusive load monitoring (NILM where the detailed data of the appliances used in houses are obtained by analyzing changes in the voltage and current. This paper focuses on developing an automatic power load event detection and appliance classification based on machine learning. In power load event detection, the paper presents a new transient detection algorithm. By turn-on and turn-off transient waveforms analysis, it can accurately detect the edge point when a device is switched on or switched off. The proposed load classification technique can identify different power appliances with improved recognition accuracy and computational speed. The load classification method is composed of two processes including frequency feature analysis and support vector machine. The experimental results indicated that the incorporation of the new edge detection and turn-on and turn-off transient signature analysis into NILM revealed more information than traditional NILM methods. The load classification method has achieved more than ninety percent recognition rate.
Application of active power sensitivity to frequency and voltage variations on load shedding
Girgis, Adly A. [Clemson University, 303 Riggs Hall, Clemson, SC 29634-0915 (United States); Mathure, Shruti [ITC Holdings, MI (United States)
2010-03-15
The occurrence of a large disturbance in a power system can lead to a decline in the system frequency and bus voltages due to a real and reactive power deficiency or due to the formation of islands with generation-load imbalance. Load shedding is an emergency control action that can prevent a blackout in the power system by relieving the overload in some parts of the system. This paper shows that rate of change of frequency can be utilized to determine the magnitude of generation-load imbalance, while the rate of change of voltage with respect to active power can be utilized to identify the sensitive bus for load shedding. The frequency, voltages and their rate of change can be obtained by means of measurements in real-time from various devices such as digital recorders or phasor measurement units or these parameters can be estimated from the voltage data by other means such as an optimal estimation method like Kalman filtering. The rate of change of system frequency, along with the equivalent system inertia may be used to estimate the magnitude of the disturbance prior to each load shedding step. The buses with a higher rate of change of voltage may be identified as the critical ones for load shedding and load can be first shed at these buses, depending on the change in the power flow at each bus. This application is tested on the IEEE 30 bus system and the preliminary results demonstrate that it is feasible to be used in load shedding to restore system voltage and frequency. (author)
Noguchi, Toshihiko; Imoto, Masaru; Sato, Yoshikazu
This paper proposes a novel three-phase power distribution system feeding trapezoidal voltages to various power electronic loads with diode rectifier front-ends. The network distributes trapezoidal voltages generated by synchronous superposition of wave-shaping voltages onto sinusoidal voltages available from a utility power grid. The power distribution by the trapezoidal voltages allows reducing harmonics of the line currents without electronic switching devices because of a spontaneously widened conduction period of the current waveforms. The reduction of the harmonic currents also contributes to improve total power factor at the load input terminals and efficiency of the power transmission cables. Since the diodes of the rectifiers successively commutate the trapezoidal waves during periods of their flat parts, not only total harmonic distortion of the currents is improved, but also voltage ripple across the dc-buses of the rectifiers can effectively be reduced with less filter capacitors. In addition, the system offers an uninterruptible power supply function by immediately changing its outputs from the wave-shaping voltages to the trapezoidal voltages when interruption occurs in the power grid. In this paper, a prototype of the system is experimentally examined from various angles of operating characteristics and test results are presented to prove feasibility of the proposed system.
Zhang, Baohua; Hu, Weihao; Hou, Peng
2015-01-01
Inclusion of the wake effect in the wind farm control design (WF) can increase the total captured power by wind turbines (WTs), which is usually implemented by derating upwind WTs. However, derating the WT without a proper control strategy will increase the structural loads, caused by operation i...
Effect of resistive load on the inspiratory work and power of breathing during exertion.
Thomas Powell
Full Text Available The resistive work of breathing against an external load during inspiration (WR(I was measured at the mouth, during sub-maximal exercise in healthy participants. This measure (which excludes the elastic work component allows the relationship between resistive work and power, ventilation and exercise modality to be explored. A total of 45 adult participants with healthy lung function took part in a series of exercise protocols, in which the relationship between WR(I, power of breathing, PR(I and minute ventilation, [Formula: see text] were assessed during rest, while treadmill walking or ergometer cycling, over a range of exercise intensities (up to 150 Watts and ventilation rates (up to 48 L min(-1 with applied constant resistive loads of 0.75 and 1.5 kPa.L.sec(-1. Resting WR(I was 0.12 JL(-1 and PR(I was 0.9 W. At each resistive load, independent of the breathing pattern or exercise mode, the WR(I increased in a linear fashion at 20 mJ per litre of [Formula: see text], while PR(I increased exponentially. With increasing resistive load the work and power at any given [Formula: see text] increased exponentially. Calculation of the power to work ratio during loaded breathing suggests that loads above 1.5 kPa.L.sec(-1 make the work of resistive breathing become inhibitive at even a moderate [Formula: see text] (>30 L sec(-1. The relationship between work done and power generated while breathing against resistive loads is independent of the exercise mode (cycling or walking and that ventilation is limited by the work required to breathe, rather than an inability to maintain or generate power.
Djukanovic, M. (Inst. ' Nikola Tesla' , Belgrade (Yugoslavia)); Sobajic, D.J.; Yohhan Pao (Case Western Reserve Univ., Cleveland, OH (United States). Dept. of Electrical Engineering and Applied Physics Case Western Reserve Univ., Cleveland, OH (United States). Dept. of Computer Engineering and Science AI WARE inc., Cleveland, OH (United States))
1992-10-01
In heavily stressed power systems, post-fault transient voltage dips can lead to undesired tripping of industrial drives and large induction motors. The lowest transient voltage dips occur when fault clearing times are less than critical ones. In this paper, we propose a new iterative analytical methodology to obtain more accurate estimates of voltage dips at maximum angular swing in direct transient stability analysis. We also propose and demonstrate the possibility of storing the results of these computations in the associative memory (AM) system, which exhibits remarkable generalization capabilities. Feature-based models stored in the AM can be utilized for fast and accurate prediction of the location, duration and the amount of the worst voltage dips, thereby avoiding the need and cost for lengthy time-domain simulations. Numerical results obtained using the example of the New England power system are presented to illustrate our approach. (Author)
Her-Terng Yau
2013-01-01
Full Text Available An extremum seeking control (ESC scheme is proposed for maximum power point tracking (MPPT in photovoltaic power generation systems. The robustness of the proposed scheme toward irradiance changes is enhanced by implementing the ESC scheme using a sliding mode control (SMC law. In the proposed approach, the chattering phenomenon caused by high frequency switching is suppressed by means of a sliding layer concept. Moreover, in implementing the proposed controller, the optimal value of the gain constant is determined using a particle swarm optimization (PSO algorithm. The experimental and simulation results show that the proposed PSO-based sliding mode ESC (SMESC control scheme yields a better transient response, steady-state stability, and robustness than traditional MPPT schemes based on gradient detection methods.
Chen, Xi Lin; De Santis, Valerio; Umenei, Aghuinyue Esai
2014-07-07
In this study, the maximum received power obtainable through wireless power transfer (WPT) by a small receiver (Rx) coil from a relatively large transmitter (Tx) coil is numerically estimated in the frequency range from 100 kHz to 10 MHz based on human body exposure limits. Analytical calculations were first conducted to determine the worst-case coupling between a homogeneous cylindrical phantom with a radius of 0.65 m and a Tx coil positioned 0.1 m away with the radius ranging from 0.25 to 2.5 m. Subsequently, three high-resolution anatomical models were employed to compute the peak induced field intensities with respect to various Tx coil locations and dimensions. Based on the computational results, scaling factors which correlate the cylindrical phantom and anatomical model results were derived. Next, the optimal operating frequency, at which the highest transmitter source power can be utilized without exceeding the exposure limits, is found to be around 2 MHz. Finally, a formulation is proposed to estimate the maximum obtainable power of WPT in a typical room scenario while adhering to the human body exposure compliance mandates.
Non Intrusive Load Identification with Power and Impedance obtained from Smart Meters
Diana Lucia Racines
2014-08-01
Full Text Available Power networks modernization toward smart grids has encouraged the use of smart meters, opening opportunities for the development of new applications to improve energy efficiency of consumers, as nonintrusive load monitoring. This paper presents a nonintrusive load identification and characterization model with real power and impedance by using artificial neural network. The approach involved the use of real power and impedance measures obtained from an educational building to represent the consumption behaviour of loads and to identify the operation states. Transitions between operation states of devices are identified as events. Common operation states transitions were used to create a representative set of events to train the multilayer feed-forward neural network designed. Comparisons between the conventional power model and the proposed mixed power-impedance model were achieved and results showed that the proposed method was better to identify loads and characterize the consumption behaviour. This model has been proposed to detect load variation in real applications using smart meters.
Effect of countermovement on elbow joint extension power-load characteristics.
Miyamoto, Naokazu; Wakahara, Taku; Sugisaki, Norihide; Murata, Koichiro; Kanehisa, Hiroaki; Fukunaga, Tetsuo; Kawakami, Yasuo
2010-12-01
The aim of the present study was to examine elbow joint extension power-load characteristics with and without a countermovement. Eight male participants performed maximal elbow extensions with and without a countermovement against different loads (0, 2.5, 5.0, 7.5, 10.0, 12.5, and 15.0 kg). Electromyographic activity of the lateral and long heads of the triceps brachii and the biceps brachii muscles was recorded. The average joint power in the concentric phase was significantly enhanced in the countermovement condition at all loads except for 0 kg. The optimal load for the maximal joint power was greater in the countermovement (7.5 kg) than in the no countermovement condition (5.0 kg). Electromyographic activity was unchanged over the intensities and conditions. Our results suggest that the optimal load for the maximal joint power depends on the type of action (i.e. with or without a counter-movement), and that the enhanced joint power in the countermovement condition is due primarily to the storage and utilization of elastic energy.
Coating service experience with a peak load power gas turbine
Rybnikov, A.I.; Tchizhik, A.A.; Getsov, L.B. [The Polzunov Central Boiler and Turbine Inst., St. Petersburg (Russian Federation); Leontiev, S.A. [Leningradsky Metallitchesky Zavod, St. Petersburg (Russian Federation); Osyka, A.S. [State Area Power Station N3 of Mosenegro, Elektrogorsk (Russian Federation); Malashenko, I.S. [E.O. Paton Electric Welding Inst., Kiev (Ukraine)
1995-12-01
This paper deals with results of industrial service of turbine blades (rotating blades) made of E1893 alloy with CoCrA1Y and CoCrA1Y/YSZ coatings and of nozzle vanes made of ZhS6K with diffusion Cr-Fe coating of the gas turbine system with the peak power GT100 working in the various regions of Russia. The use of CoCrA1Y coatings retarded the formation of considerable corrosion damages, but after 7500 hours of operation pit corrosion was observed to appear in the diffusion and overlay coatings and in the base metal of buckets and nozzle vanes. The outer ceramic layer can increase the service life of turbine buckets, because sulphur compounds some difficulties to reach the surface of the coating metallic layer. (orig.)
Load, Force and Power-Velocity Relationships in the Prone Pull-Up Exercise.
Muñoz-López, Mario; Marchante, David; Cano-Ruiz, Miguel A; Chicharro, José López; Balsalobre-Fernández, Carlos
2017-03-02
To analyze the load, force and power-velocity relationships, as well as to determine the load that optimizes power output on the pull-up exercise. Eighty-two resistance trained males (Age = 26.8 ± 5.0 yrs.; Pull-up 1RM - normalized per kg of body mass- = 1.5 ± 0.34) performed two repetitions with 4 incremental loads (ranging 70-100%1-RM) in the pull-up exercise while mean propulsive velocity (MPV), force (MPF) and power (MPP) were measured using a linear transducer. Relationships between variables were studied using first and second order least-squares regression, and subjects were divided into three groups depending on their 1-RM for comparison purposes. Almost perfect individual load-velocity (R(2) = 0.975 ± 0.02), force-velocity (R(2) = 0.954 ± 0.04) and power-velocity (R(2) = 0.966 ± 0.04) relationships, which allowed to determine the velocity at each %1-RM as well as the maximal theoretical force (F0), velocity (V0) and power (Pmax) for each subject were observed. Statistically significant differences between groups were observed for F0 (p0.05). Also, high correlations between F0 and 1-RM (r = 0.811) and V0 and Pmax (r = 0.865) were observed. Finally, we observed that the load that maximized MPP was 71.0 ± 6.6 %1-RM. The very high load-velocity, force-velocity and power-velocity relationships allows to estimate 1-RM by measuring movement velocity, as well as to determine maximal force, velocity and power capabilities. This information could be of great interest for strength and conditioning coaches who wish to monitor pull-up performance.
The Maximum Power of the Wind Power System Based on Extreme Value Method%基于极值法的风电系统最大功率
陆玲黎; 吴雷
2011-01-01
针对风力发电系统的最大功率问题,提出以极值法为依据捕获最大功率的方法.分析了风力机的工作原理及功率特性,讨论了影响功率的主要因素.通过对极值搜索法的基本理论及特点的解析,结合其工作原理,得出功率曲线是占空比的凹函数,因此极值搜索法通过控制占空比来提高风能的捕获效率,并通过改进提高了抗干扰能力和稳定性.实验结果证明了该方法的可行性.%In order to overcome the trouble brought by wind power generation system for maximum power,this paper puts forward a method based on extreme value method to capture the maximum power.The working principle of wind turbine and power characteristics are analyzed,the main factors affecting the power is discussed.Through the analysis of extremum search method on the basic theory and characteristics which combined with its working principle, come to a decision that power curve is concave function of duty cycle.Therefore,extreme value search method can control the duty cycle to improve the efficiency of wind capture, and improve anti-interference ability and stability .Through experiments, the final experimental curves obtained prove the feasibility of the method.
Balachandran, Anoop T; Gandia, Kristine; Jacobs, Kevin A; Streiner, David L; Eltoukhy, Moataz; Signorile, Joseph F
2017-08-10
Power training has been shown to be more effective than conventional resistance training for improving physical function in older adults; however, most trials have used pneumatic machines during training. Considering that the general public typically has access to plate-loaded machines, the effectiveness and safety of power training using plate-loaded machines compared to pneumatic machines is an important consideration. The purpose of this investigation was to compare the effects of high-velocity training using pneumatic machines (Pn) versus standard plate-loaded machines (PL). Independently-living older adults, 60years or older were randomized into two groups: pneumatic machine (Pn, n=19) and plate-loaded machine (PL, n=17). After 12weeks of high-velocity training twice per week, groups were analyzed using an intention-to-treat approach. Primary outcomes were lower body power measured using a linear transducer and upper body power using medicine ball throw. Secondary outcomes included lower and upper body muscle muscle strength, the Physical Performance Battery (PPB), gallon jug test, the timed up-and-go test, and self-reported function using the Patient Reported Outcomes Measurement Information System (PROMIS) and an online video questionnaire. Outcome assessors were blinded to group membership. Lower body power significantly improved in both groups (Pn: 19%, PL: 31%), with no significant difference between the groups (Cohen's d=0.4, 95% CI (-1.1, 0.3)). Upper body power significantly improved only in the PL group, but showed no significant difference between the groups (Pn: 3%, PL: 6%). For balance, there was a significant difference between the groups favoring the Pn group (d=0.7, 95% CI (0.1, 1.4)); however, there were no statistically significant differences between groups for PPB, gallon jug transfer, muscle muscle strength, timed up-and-go or self-reported function. No serious adverse events were reported in either of the groups. Pneumatic and plate-loaded
Yaw-Misalignment and its Impact on Wind Turbine Loads and Wind Farm Power Output
van Dijk, Mike T.; van Wingerden, Jan-Willem; Ashuri, Turaj; Li, Yaoyu; Rotea, Mario A.
2016-09-01
To make wind energy cost competitive with traditional resources, wind turbines are commonly placed in groups. Aerodynamic interaction between the turbines causes sub-optimal energy production. A control strategy to mitigate these losses is by redirecting the wake by yaw misalignment. This paper aims to assess the influence of load variations of the rotor due to partial wake overlap and presents a combined optimization of the power and loads using wake redirection. For this purpose, we design a computational framework which computes the wind farm power production and the wind turbine rotor loads based on the yaw settings. The simulation results show that partial wake overlap can significantly increase asymmetric loading of the rotor disk and that yaw misalignment is beneficial in situations where the wake can be sufficiently directed away from the downstream turbine.
Observer-Based Load Frequency Control for Island Microgrid with Photovoltaic Power
Chaoxu Mu
2017-01-01
Full Text Available As renewable energy is widely integrated into the power system, the stochastic and intermittent power generation from renewable energy may cause system frequency deviating from the prescribed level, especially for a microgrid. In this paper, the load frequency control (LFC of an island microgrid with photovoltaic (PV power and electric vehicles (EVs is investigated, where the EVs can be treated as distributed energy storages. Considering the disturbances from load change and PV power, an observer-based integral sliding mode (OISM controller is designed to regulate the frequency back to the prescribed value, where the neural network observer is used to online estimate the PV power. Simulation studies on a benchmark microgrid system are presented to illustrate the effectiveness of OISM controller, and comparative results also demonstrate that the proposed method has a superior performance for stabilizing the frequency over the PID control.
Shareef, Hussain; Mutlag, Ammar Hussein; Mohamed, Azah
2017-01-01
Many maximum power point tracking (MPPT) algorithms have been developed in recent years to maximize the produced PV energy. These algorithms are not sufficiently robust because of fast-changing environmental conditions, efficiency, accuracy at steady-state value, and dynamics of the tracking algorithm. Thus, this paper proposes a new random forest (RF) model to improve MPPT performance. The RF model has the ability to capture the nonlinear association of patterns between predictors, such as irradiance and temperature, to determine accurate maximum power point. A RF-based tracker is designed for 25 SolarTIFSTF-120P6 PV modules, with the capacity of 3 kW peak using two high-speed sensors. For this purpose, a complete PV system is modeled using 300,000 data samples and simulated using the MATLAB/SIMULINK package. The proposed RF-based MPPT is then tested under actual environmental conditions for 24 days to validate the accuracy and dynamic response. The response of the RF-based MPPT model is also compared with that of the artificial neural network and adaptive neurofuzzy inference system algorithms for further validation. The results show that the proposed MPPT technique gives significant improvement compared with that of other techniques. In addition, the RF model passes the Bland-Altman test, with more than 95 percent acceptability.
Zagrouba, M.; Sellami, A.; Bouaicha, M. [Laboratoire de Photovoltaique, des Semi-conducteurs et des Nanostructures, Centre de Recherches et des Technologies de l' Energie, Technopole de Borj-Cedria, Tunis, B.P. 95, 2050 Hammam-Lif (Tunisia); Ksouri, M. [Unite de Recherche RME-Groupe AIA, Institut National des Sciences Appliquees et de Technologie (Tunisia)
2010-05-15
In this paper, we propose to perform a numerical technique based on genetic algorithms (GAs) to identify the electrical parameters (I{sub s}, I{sub ph}, R{sub s}, R{sub sh}, and n) of photovoltaic (PV) solar cells and modules. These parameters were used to determine the corresponding maximum power point (MPP) from the illuminated current-voltage (I-V) characteristic. The one diode type approach is used to model the AM1.5 I-V characteristic of the solar cell. To extract electrical parameters, the approach is formulated as a non convex optimization problem. The GAs approach was used as a numerical technique in order to overcome problems involved in the local minima in the case of non convex optimization criteria. Compared to other methods, we find that the GAs is a very efficient technique to estimate the electrical parameters of PV solar cells and modules. Indeed, the race of the algorithm stopped after five generations in the case of PV solar cells and seven generations in the case of PV modules. The identified parameters are then used to extract the maximum power working points for both cell and module. (author)
Chad Pope; Larry L. Taylor; Soon Sam Kim
2007-02-01
This document represents a summary version of the criticality analysis done to support loading SNF in a Type 1a basket/standard canister combination. Specifically, this engineering design file (EDF) captures the information pertinent to the intact condition of four fuel types with different fissile loads and their calculated reactivities. These fuels are then degraded into various configurations inside a canister without the presence of significant moderation. The important aspect of this study is the portrayal of the fuel degradation and its effect on the reactivity of a single canister given the supposition there will be continued moderation exclusion from the canister. Subsequent analyses also investigate the most reactive ‘dry’ canister in a nine canister array inside a hypothetical transport cask, both dry and partial to complete flooding inside the transport cask. The analyses also includes a comparison of the most reactive configuration to other benchmarked fuels using a software package called TSUNAMI, which is part of the SCALE 5.0 suite of software.
Furbish, David J.; Schmeeckle, Mark; Schumer, Rina; Fathel, Siobhan L.
2016-01-01
We describe the most likely forms of the probability distributions of bed load particle velocities, accelerations, hop distances, and travel times, in a manner that formally appeals to inferential statistics while honoring mechanical and kinematic constraints imposed by equilibrium transport conditions. The analysis is based on E. Jaynes's elaboration of the implications of the similarity between the Gibbs entropy in statistical mechanics and the Shannon entropy in information theory. By maximizing the information entropy of a distribution subject to known constraints on its moments, our choice of the form of the distribution is unbiased. The analysis suggests that particle velocities and travel times are exponentially distributed and that particle accelerations follow a Laplace distribution with zero mean. Particle hop distances, viewed alone, ought to be distributed exponentially. However, the covariance between hop distances and travel times precludes this result. Instead, the covariance structure suggests that hop distances follow a Weibull distribution. These distributions are consistent with high-resolution measurements obtained from high-speed imaging of bed load particle motions. The analysis brings us closer to choosing distributions based on our mechanical insight.
Hongze Li
2014-01-01
Full Text Available Short-term power load forecasting is one of the most important issues in the economic and reliable operation of electricity power system. Taking the characteristics of randomness, tendency, and periodicity of short-term power load into account, a new method (SSA-AR model which combines the univariate singular spectrum analysis and autoregressive model is proposed. Firstly, the singular spectrum analysis (SSA is employed to decompose and reconstruct the original power load series. Secondly, the autoregressive (AR model is used to forecast based on the reconstructed power load series. The employed data is the hourly power load series of the Mid-Atlantic region in PJM electricity market. Empirical analysis result shows that, compared with the single autoregressive model (AR, SSA-based linear recurrent method (SSA-LRF, and BPNN (backpropagation neural network model, the proposed SSA-AR method has a better performance in terms of short-term power load forecasting.
Stability Enhancement Based on Virtual Impedance for DC Microgrids with Constant Power Loads
Lu, Xiaonan; Sun, Kai; Guerrero, Josep M.; Quintero, Juan Carlos Vasquez; Huang, Lipei; Wang, Jianhui
2015-01-01
In this paper, a converter-based DC microgrid is studied. By considering the impact of each component in DC microgrids on system stability, a multi-stage configuration is employed, which includes the source stage, interface converter stage between buses and common load stage. In order to study the overall stability of the above DC microgrid with constant power loads (CPLs), a comprehensive small-signal model is derived by analyzing the interface converters in each stage. The instability issue...
Impacts of Electric Vehicle Loads on Power Distribution Systems
Pillai, Jayakrishnan Radhakrishna; Bak-Jensen, Birgitte
2010-01-01
Electric vehicles (EVs) are the most promising alternative to replace a significant amount of gasoline vehicles to provide cleaner, CO2 free and climate friendly transportation. On integrating more electric vehicles, the electric utilities must analyse the related impacts on the electricity syste...... be accommodated in the network with the smart charging mode. The extent of integrating EVs in an area is constrained by the EV charging behavior and the safe operational limits of electricity system parameters....... operation. This paper investigates the effects on the key power distribution system parameters like voltages, line drops, system losses etc. by integrating electric vehicles in the range of 0-50% of the cars with different charging capacities. The dump as well as smart charging modes of electric vehicles......Electric vehicles (EVs) are the most promising alternative to replace a significant amount of gasoline vehicles to provide cleaner, CO2 free and climate friendly transportation. On integrating more electric vehicles, the electric utilities must analyse the related impacts on the electricity system...
Analysis of Wind Power and Load Data at Multiple Time Scales
Coughlin, Katie; Eto, J.H.
2010-12-20
In this study we develop and apply new methods of data analysis for high resolution wind power and system load time series, to improve our understanding of how to characterize highly variable wind power output and the correlations between wind power and load. These methods are applied to wind and load data from the ERCOT region, and wind power output from the PJM and NYISO areas. We use a wavelet transform to apply mathematically well-defined operations of smoothing and differencing to the time series data. This approach produces a set of time series of the changes in wind power and load (or ?deltas?), over a range of times scales from a few seconds to approximately one hour. A number of statistical measures of these time series are calculated. We present sample distributions, and devise a method for fitting the empirical distribution shape in the tails. We also evaluate the degree of serial correlation, and linear correlation between wind and load. Our examination of the data shows clearly that the deltas do not follow a Gaussian shape; the distribution is exponential near the center and appears to follow a power law for larger fluctuations. Gaussian distributions are frequently used in modeling studies. These are likely to over-estimate the probability of small to moderate deviations. This in turn may lead to an over-estimation of the additional reserve requirement (hence the cost) for high penetration of wind. The Gaussian assumption provides no meaningful information about the real likelihood of large fluctuations. The possibility of a power law distribution is interesting because it suggests that the distribution shape for of wind power fluctuations may become independent of system size for large enough systems.
Reza Sedaghati
2013-09-01
Full Text Available In this paper, the structure of Hybrid Power Flow Controller (HPFC is proposed in order to improve static voltage stability characteristics. HPFC forms a hybrid controller using IPFC series converters as a hybrid with existing parallel and passive compensator (SVC in power system. Utilization of hybrid structures makes it possible to use converters for improving performance of both old and existing compensators in power networks. In this study, the power injection model (PIM is used to model the hybrid power flow controller in Newton load flow. The aforementioned model is simulated in MATLAB software. The P-V curves of PQ buses of a typical system are evaluated by a continuous power flow (CPF method to analyses the effect of this controller on static voltage stability characteristics. Meanwhile, SVC as existing devices in the system and UPFC and IPFC as state-of-the-art compensator devices are compared with the proposed hybrid structure. The amount of active and reactive power loss and improvement of loading limit of the system are used as main parameters in our comparison.
Fluctuation analysis of high frequency electric power load in the Czech Republic
Kracík, Jiří
2016-01-01
We analyze the electric power load in the Czech Republic (CR) which exhibits a seasonality as well as other oscillations typical for European countries. Moreover, we detect 1/f noise property of electrical power load with extra additional peaks that allows to separate it into a deterministic and stochastic part. We then focus on the analysis of the stochastic part using improved Multi-fractal Detrended Fluctuation Analysis method (MFDFA) to investigate power load datasets with a minute resolution. Extracting the noise part of the signal by using Fourier transform allows us to apply this method to obtain the fluctuation function and to estimate the generalized Hurst exponent together with the correlated Hurst exponent, its improvement for the non-Gaussian datasets. The results exhibit a strong presence of persistent behaviour and the dataset is characterized by a non-Gaussian skewed distribution. There are also indications for the presence of the probability distribution that has heavier tail than the Gaussian...
Study on Impact of Electric Vehicles Charging Models on Power Load
Cheng, Chen; Hui-mei, Yuan
2017-05-01
With the rapid increase in the number of electric vehicles, which will lead the power load on grid increased and have an adversely affect. This paper gives a detailed analysis of the following factors, such as scale of the electric cars, charging mode, initial charging time, initial state of charge, charging power and other factors. Monte Carlo simulation method is used to compare the two charging modes, which are conventional charging and fast charging, and MATLAB is used to model and simulate the electric vehicle charging load. The results show that compared with the conventional charging mode, fast charging mode can meet the requirements of fast charging, but also bring great load to the distribution network which will affect the reliability of power grid.
Hill, D.C. [University Coll. of North Wales, Menai Bridge (United Kingdom). School of Ocean Science; Infield, D.G. [Loughborough Univ. of Technology (United Kingdom). Dept. of Electronic and Electrical Engineering
1995-11-01
A load forecasting technique, based upon an autoregressive (AR) method is presented. Its use for short term load forecasting is assessed by direct comparison with real forecasts made by human operators of the Lerwick power station on the Shetland Islands. A substantial improvement in load prediction, as measured by a reduction of RMS error, is demonstrated. Shetland has a total installed capacity of about 68 MW, and an average load (1990) of around 20 MW. Although the operators could forecast the load for a few distinct hours better than the AR method, results from simulations of the scheduling and operation of the generating plant show that the AR forecasts provide increased overall system performance. A detailed model of the island power system, which includes plant scheduling, was run using the AR and Lerwick operators` forecasts as input to the scheduling routine. A reduction in plant cycling, underloading and fuel consumption was obtained using the AR forecasts rather than the operators` forecasts in simulations over a 28 day study period. It is concluded that the load forecasting method presented could be of benefit to the operators of such mesoscale power systems. (author)
Chen Pоуu
2013-01-01
Full Text Available Products made overseas but sold in Taiwan are very common. Regarding the cross-border or interregional production and marketing of goods, inventory decision-makers often have to think about how to determine the amount of purchases per cycle, the number of transport vehicles, the working hours of each transport vehicle, and the delivery by ground or air transport to sales offices in order to minimize the total cost of the inventory in unit time. This model assumes that the amount of purchases for each order cycle should allow all rented vehicles to be fully loaded and the transport times to reach the upper limit within the time period. The main research findings of this study included the search for the optimal solution of the integer planning of the model and the results of sensitivity analysis.
Feyrer, R.
1994-12-31
A preliminary simulator establishes the maximum possible load change in a pumped storage power plant. The complex hydraulic system of such power plants renders controlling of their operation difficult. The preliminary simulator continuously determines the maximum permissible turbine output and number of pumps at each instance, thereby facilitating power plant operation control. This simulator is installed at the Witznau power plant and is currently undergoing intense testing. It will be integrated into the new process control system installed in 1994. (orig.) [Deutsch] Der Vorabsimulator ermittelt die maximal moegliche Lastaenderung in einem Pumpspeicherwerk. Das komplizierte Wasserfuehrungsystem des Pumpspeicherwerks erschwert die Betriebsfuehrung. Der Vorabsimulator bestimmt kontinuierlich die momentan maximal zulaessige Turbinenleistung und Pumpenanzahl, und erleichtert damit die Betriebsfuehrung des Kraftwerks. Der Vorabsimulator ist im Kraftwerk Witznau installiert und wird derzeit intensiv getestet. Eine Einbindung in die neue Leittechnik, die 1994 installiert wird, ist vorgesehen. (orig.)
A Wind Farm Active Power Dispatch Strategy for Fatigue Load Reduction
Zhang, Baohua; N. Soltani, Mohsen; Hu, Weihao;
2016-01-01
, while the wind farm is following certain power references given by the network operator. The damage equivalent loads are included in the objective function by means of lookup tables generated under a series of working conditions. A Modified Particle Swarm Optimization algorithm is used to solve......One of the biggest challenges in wind farm management is to cope with requirements from the grid companies and to optimize efficiency and minimize wear on wind turbines. This paper addresses an optimized active power dispatch strategy of a wind farm to reduce the fatigue load of wind turbines...
Kelisani, M. Dayyani; Doebert, S.; Aslaninejad, M.
2016-08-01
The critical process of beam loading compensation in high intensity accelerators brings under control the undesired effect of the beam induced fields to the accelerating structures. A new analytical approach for optimizing standing wave accelerating structures is found which is hugely fast and agrees very well with simulations. A perturbative analysis of cavity and waveguide excitation based on the Bethe theorem and normal mode expansion is developed to compensate the beam loading effect and excite the maximum field gradient in the cavity. The method provides the optimum values for the coupling factor and the cavity detuning. While the approach is very accurate and agrees well with simulation software, it massively shortens the calculation time compared with the simulation software.
Kelisani, M. Dayyani, E-mail: mdayyani@cern.ch [Institute for Research in Fundamental Sciences (IPM), School of Particles and Accelerators, P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of); European Organization for Nuclear Research (CERN), BE Department, CH-1211 Geneva 23 (Switzerland); Doebert, S. [European Organization for Nuclear Research (CERN), BE Department, CH-1211 Geneva 23 (Switzerland); Aslaninejad, M. [Institute for Research in Fundamental Sciences (IPM), School of Particles and Accelerators, P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of)
2016-08-21
The critical process of beam loading compensation in high intensity accelerators brings under control the undesired effect of the beam induced fields to the accelerating structures. A new analytical approach for optimizing standing wave accelerating structures is found which is hugely fast and agrees very well with simulations. A perturbative analysis of cavity and waveguide excitation based on the Bethe theorem and normal mode expansion is developed to compensate the beam loading effect and excite the maximum field gradient in the cavity. The method provides the optimum values for the coupling factor and the cavity detuning. While the approach is very accurate and agrees well with simulation software, it massively shortens the calculation time compared with the simulation software.
Load Flow and Short Circuit Analysis of the Class III Power System of HANARO
Kim, H. K.; Jung, H. S
2005-12-15
The planning, design, and operation of electric power system require engineering studies to assist in the evaluation of the system performance, reliability, safety and economics. The Class III power of HANARO supplies power for not only HANARO but also RIPF and IMEF. The starting current of most ac motors is five to ten times normal full load current. The loads of the Class III power are connected in consecutive orders at an interval for 10 seconds to avoid excessive voltage drop. This technical report deals with the load flow study and motor starting study for the Class III power of HANARO using ETAP(Electrical Transient Analyzer Program) to verify the capacity of the diesel generator. Short-circuit studies are done to determine the magnitude of the prospective currents flowing throughout the power system at various time intervals after a fault occurs. Short-circuit studies can be performed at the planning stage in order to help finalize the system layout, determine voltage levels, and size cables, transformers, and conductors. From this study, we verify the short circuit current capacity of air circuit breaker(ACB) and automatic transfer switch(ATS) of the Class III power.
Bossuyt, Juliaan; Howland, Michael; Meneveau, Charles; Meyers, Johan
2015-11-01
To optimize wind farm layouts for a maximum power output and wind turbine lifetime, mean power output measurements in wind tunnel studies are not sufficient. Instead, detailed temporal information about the power output and unsteady loading from every single wind turbine in the wind farm is needed. A very small porous disc model with a realistic thrust coefficient of 0.75 - 0.85, was designed. The model is instrumented with a strain gage, allowing measurements of the thrust force, incoming velocity and power output with a frequency response up to the natural frequency of the model. This is shown by reproducing the -5/3 spectrum from the incoming flow. Thanks to its small size and compact instrumentation, the model allows wind tunnel studies of large wind turbine arrays with detailed temporal information from every wind turbine. Translating to field conditions with a length-scale ratio of 1:3,000 the frequencies studied from the data reach from 10-4 Hz up to about 6 .10-2 Hz. The model's capabilities are demonstrated with a large wind farm measurement consisting of close to 100 instrumented models. A high correlation is found between the power outputs of stream wise aligned wind turbines, which is in good agreement with results from prior LES simulations. Work supported by ERC (ActiveWindFarms, grant no. 306471) and by NSF (grants CBET-113380 and IIA-1243482, the WINDINSPIRE project).
Sudip K. Mazumder
2005-12-31
Development of high-performance and durable solidoxide fuel cells (SOFCs) and a SOFC power-generating system requires knowledge of the feedback effects from the power-conditioning electronics and from application-electrical-power circuits that may pass through or excite the power-electronics subsystem (PES). Therefore, it is important to develop analytical models and methodologies, which can be used to investigate and mitigate the effects of the electrical feedbacks from the PES and the application loads (ALs) on the reliability and performance of SOFC systems for stationary and non-stationary applications. However, any such attempt to resolve the electrical impacts of the PES on the SOFC would be incomplete unless one utilizes a comprehensive analysis, which takes into account the interactions of SOFC, PES, balance-of-plant system (BOPS), and ALs as a whole. SOFCs respond quickly to changes in load and exhibit high part- and full-load efficiencies due to its rapid electrochemistry, which is not true for the thermal and mechanical time constants of the BOPS, where load-following time constants are, typically, several orders of magnitude higher. This dichotomy can affect the lifetime and durability of the SOFCSs and limit the applicability of SOFC systems for load-varying stationary and transportation applications. Furthermore, without validated analytical models and investigative design and optimization methodologies, realizations of cost-effective, reliable, and optimal PESs (and power-management controls), in particular, and SOFC systems, in general, are difficult. On the whole, the research effort can lead to (a) cost-constrained optimal PES design for high-performance SOFCS and high energy efficiency and power density, (b) effective SOFC power-system design, analyses, and optimization, and (c) controllers and modulation schemes for mitigation of electrical impacts and wider-stability margin and enhanced system efficiency.
Advances in electric power and energy systems load and price forecasting
2017-01-01
A comprehensive review of state-of-the-art approaches to power systems forecasting from the most respected names in the field, internationally. Advances in Electric Power and Energy Systems is the first book devoted exclusively to a subject of increasing urgency to power systems planning and operations. Written for practicing engineers, researchers, and post-grads concerned with power systems planning and forecasting, this book brings together contributions from many of the world’s foremost names in the field who address a range of critical issues, from forecasting power system load to power system pricing to post-storm service restoration times, river flow forecasting, and more. In a time of ever-increasing energy demands, mounting concerns over the environmental impacts of power generation, and the emergence of new, smart-grid technologies, electricity price forecasting has assumed a prominent role within both the academic and industrial ar nas. Short-run forecasting of electricity prices has become nece...
Michelle Lim Sern Mi
2013-01-01
Full Text Available This research work presents a novel architecture of an Ultra-Low-Power (ULP based Hybrid Energy Harvester (HEH consisting of multiple input sources such as kinetic, thermal and solar energy, harvested from passive human power. Having multiple ambient sources mitigates limitations caused by single sources especially for bodily-worn applications; however, this results in impedance mismatch among the different integrated sources. To overcome this limitation, the proposed ULP-HEH will use one power management unit with Maximum Power Point Tracking (MPPT algorithm and impedance matching considerations to efficiently manage and combine power harvested from all three sources to achieve ULP consumptions. Among other crucial sub-modules of the ULP-HEH are its Asynchronous Finite State Machine (AFSM cum resource sharing arbiter to prioritize and share energy sources for overall power reduction, an efficient rectification scheme for the piezoelectric input, an adaptive feedback for ULP conditioning, Zero-Current Switching (ZCS for semi-lossless switching, a self-start circuit for low ambient startup, a Boost converter, a Buck regulator, a fuzzy-based micro-battery charger and a de-multiplexer to switch between harvesting or charging capabilities. All of which are implemented for maximum output extraction and minimal losses. This ULP-HEH will be developed in PSPICE software, Verilog coding under Mentor Graphics environment and later to be verified using Field Programmable Gate Array (FPGA board before the final layout implementation in CMOS 0.13-Âµm process technology. This battery-less ULP-HEH is expected to deliver 3.0-5.0V of regulated voltage output from low ambient sources of 35 mV at startup. An efficiency of 90% with an output power of 650 Âµm is expected when all sources are summed. Also, this ULP-HEH is aimed at reducing power consumption to at least twice (<70 ÂµW of conventional approaches. The proposed ULP-HEH can be used for ULP bodily
An adaptive load-following control system for a space nuclear power system
Metzger, John D.; El-Genk, Mohamed S.
An adaptive load-following control system is proposed for a space nuclear power system. The conceptual design of the SP-100 space nuclear power system proposes operating the nuclear reactor at a base thermal power and accommodating changes in the electrical power demand with a shunt regulator. It is necessary to increase the reactor thermal power if the payload electrical demand exceeds the peak system electrical output for the associated reactor power. When it is necessary to change the nuclear reactor power to meet a change in the power demand, the power ascension or descension must be accomplished in a predetermined manner to avoid thermal stresses in the system and to achieve the desired reactor period. The load-following control system described has the ability to adapt to changes in the system and to changes in the satellite environment. The application is proposed of the model reference adaptive control (MRAC). The adaptive control system has the ability to control the dynamic response of nonlinear systems. Three basic subsets of adaptive control are: (1) gain scheduling, (2) self-tuning regulators, and (3) model reference adaptive control.
Analysis on capability of load following for nuclear power plants abroad and its enlightenment
Zheng, Kuan; Zhang, Fu-qiang; Deng, Ting-ting; Zhang, Jin-fang; Hao, Weihua
2017-01-01
With the acceleration adjustment of China’s energy structure, the development of nuclear power plants in China has been going back to the fast track. While as the trend of slowing electric power demand is now unmistakable, it enforces the power system to face much greater pressure in some coastal zones where the nuclear power plants are of a comparative big proportion, such as Fujian province and Liaoning province. In this paper, the capability of load following of nuclear power plants of some developed countries with high proportion of nuclear power generation such as France, US and Japan are analysed, also from the aspects including the safety, the economy and their practical operation experience is studied. The feasibility of nuclear power plants to participate in the peak regulation of system is also studied and summarized. The results of this paper could be of good reference value for the China’s nuclear power plants to participate in system load following, and also of great significance for the development of the nuclear power plants in China.
Thermal loading of wind power converter considering dynamics of wind speed
Baygildina, Elvira; Peltoniemi, Pasi; Pyrhönen, Olli;
2013-01-01
The thermal loading of power semiconductors is a crucial performance related to the reliability and cost of the wind power converter. However, the thermal loading impacts by the variation of wind speeds have not yet been clarified, especially when considering the aerodynamic behavior of the wind...... turbines. In this paper, the junction temperatures in the wind power converter are studied under not only steady state, but also turbulent wind speed conditions. The study is based on a 1.5 MW direct-driven turbine system with aerodynamic model described by Unsteady Blade Element Momentum Method (BEMM......), and the thermal stress of power devices is investigated from the frequency spectrum point of view of wind speed. It is concluded that because of the strong inertia effects by the aerodynamic behavior of wind turbines, thermal stress of the semiconductors is relatively more stable and only influenced by the low...
Matlab for Forecasting of Electric Power Load Based on BP Neural Network
Wang, Xi-Ping; Shi, Ming-Xi
Modeling and predicting electricity consumption play a vital role both in developed and developing countries for policy makers and related organizations. Improve load forecasting technology level is not only beneficial to plan power management and make reasonable construction plan, but also good for saving energy and reducing power cost, and then, it can improve the economic benefits and social benefit for power system. BP neural network is one of the most widely used neural networks and it has many advantages in the power load forecasting. Matlab has become the best technology application software which has been internationally recognized, the software has many characteristics, such as data visualization function and neural network toolbox, for these, it is the essential software when we do some research on neural network.
Abbas, Nikhar; Tom, Nathan
2017-09-01
Wave energy converter (WEC) control strategies have been primarily focused on maximizing power absorption. The use of model predictive control strategies allows for a finite-horizon, multiterm objective function to be solved. This work utilizes a multiterm objective function to maximize power absorption while minimizing the structural loads on the WEC system. Furthermore, a Kalman filter and autoregressive model were used to estimate and forecast the wave exciting force and predict the future dynamics of the WEC. The WEC's power-take-off time-averaged power and structural loads under a perfect forecast assumption in irregular waves were compared against results obtained from the Kalman filter and autoregressive model to evaluate model predictive control performance.
Theory Study and Application of the BP-ANN Method for Power Grid Short-Term Load Forecasting
Xia Hua; Gang Zhang; Jiawei Yang; Zhengyuan Li
2015-01-01
Aiming at the low accuracy problem of power system short⁃term load forecasting by traditional methods, a back⁃propagation artifi⁃cial neural network (BP⁃ANN) based method for short⁃term load forecasting is presented in this paper. The forecast points are re⁃lated to prophase adjacent data as well as the periodical long⁃term historical load data. Then the short⁃term load forecasting model of Shanxi Power Grid (China) based on BP⁃ANN method and correlation analysis is established. The simulation model matches well with practical power system load, indicating the BP⁃ANN method is simple and with higher precision and practicality.
The coordinated control of SVC and excitation of generators in power systems with nonlinear loads
Ruan, Yingqin; Wang, Jie [Department of Electrical Engineering, Shanghai Jiaotong University, 1954 Hua Shan Road, Shanghai 200030 (China)
2005-10-01
Based on the feedback linearized technique and control of differential and algebraic systems, the exact linearization design is presented in this paper for SVC (static var compensator) and generator excitation controllers in power systems with nonlinear loads. It can improve both the power angle stability of generators and the voltage behavior at the SVC location. Simulation results indicate that this control method has a good effect and superiority. (author)
Fatigue analysis of CANFLEX-NU fuel elements subjected to power-cyclic loads
Sim, Ki Seob; Suk, Ho Chun
1997-08-01
This report describes the fatigue analysis of the CANDU advanced fuel, so-called CANFLEX-NU, subjected to power-cyclic loads more than 1,000. The CANFLEX-NU bundle is composed of 43 elements with natural uranium fuel. As a result, the CANFLEX-NU fuel elements will maintain good integrity under the condition of 1,500 power-cycles. (author). 4 refs., 19 figs.
Qin, Zian; Wang, Huai; Blaabjerg, Frede;
2015-01-01
Thermal loading of wind power converters is critical to their reliability performance. Especially for IGBT modules applied in a converter, both of the mean value and variation of the junction temperature have significant impact on the lifetime. Besides other strategies to reduce the thermal loadi...... the temperature fluctuations due to wind speed variations. The trade-off between the reduced amplitude of temperature fluctuations and the additional power losses that may be introduced is quantitatively studied....
Matúš Krčmár
2015-09-01
Full Text Available Background: High muscular power output is required in many athletic endeavors in order for success to be achieved. In the scientific community postactivation potentiation and its effect on performance are often discussed. There are many studies where the effect of resistance exercise on motor performance (such as vertical jump performance and running speed has been investigated but only a few of them studied power output. Objective: The purpose of this study was to determine the acute responses to a 2 set loaded half-squat jumps and 2 set loaded back half-squat protocols designed to induce the acute maximum average power output during loaded half-squat jumps. Methods: A randomized cross-over design was used. 11 participants of this study performed 3 trials in randomized order separated by at least 48 hours where maximum average power output was measured. The specific conditioning activities were comprised of 2 sets and 4 repetitions of half-squat jumps, 2 sets and 4 repetitions of back half-squat exercises and a control protocol without an intervention by specific a conditioning activity. Participants were strength trained athletes with different sport specializations (e.g. ice-hockey, volleyball. Mean age of the athletes was 22 ± 1.8 years, body mass 80 ± 7.1 kg and body height 185 ± 6.5 cm. Analysis of variance with repeated measures was used to determine differences between pre- and post-condition in each protocol, as well as between conditioning protocols, and also effect size was used to evaluate practical significance. Results: Maximum average power was significantly enhanced after application of the half-squat jump condition protocol (1496.2 ± 194.5 to 1552 ± 196.1 W, Δ ~ 3.72%, p < .001 and after application of the back half-squat protocol (1500.7 ± 193.2 to 1556 ± 191.2 W, Δ ~ 3.68%, p < .001 after 10 min of rest. Power output after control protocol was
Short-term load and wind power forecasting using neural network-based prediction intervals.
Quan, Hao; Srinivasan, Dipti; Khosravi, Abbas
2014-02-01
Electrical power systems are evolving from today's centralized bulk systems to more decentralized systems. Penetrations of renewable energies, such as wind and solar power, significantly increase the level of uncertainty in power systems. Accurate load forecasting becomes more complex, yet more important for management of power systems. Traditional methods for generating point forecasts of load demands cannot properly handle uncertainties in system operations. To quantify potential uncertainties associated with forecasts, this paper implements a neural network (NN)-based method for the construction of prediction intervals (PIs). A newly introduced method, called lower upper bound estimation (LUBE), is applied and extended to develop PIs using NN models. A new problem formulation is proposed, which translates the primary multiobjective problem into a constrained single-objective problem. Compared with the cost function, this new formulation is closer to the primary problem and has fewer parameters. Particle swarm optimization (PSO) integrated with the mutation operator is used to solve the problem. Electrical demands from Singapore and New South Wales (Australia), as well as wind power generation from Capital Wind Farm, are used to validate the PSO-based LUBE method. Comparative results show that the proposed method can construct higher quality PIs for load and wind power generation forecasts in a short time.
Al-Amoudi, A.; Zhang, L. [University of Leeds (United Kingdom). School of Electronic and Electrical Engineering
2000-09-01
A neural-network-based approach for solar array modelling is presented. The logic hidden unit of the proposed network consists of a set of nonlinear radial basis functions (RBFs) which are connected directly to the input vector. The links between hidden and output units are linear. The model can be trained using a random set of data collected from a real photovoltaic (PV) plant. The training procedures are fast and the accuracy of the trained models is comparable with that of the conventional model. The principle and training procedures of the RBF-network modelling when applied to emulate the I/V characteristics of PV arrays are discussed. Simulation results of the trained RBF networks for modelling a PV array and predicting the maximum power points of a real PV panel are presented. (author)
WANG Yang; TU Zhan-Chun
2013-01-01
The Carnot-like heat engines are classified into three types (normal-,sub-and,super-dissipative) according to relations between the minimum irreversible entropy production in the "isothermal" processes and the time for completing those processes.The efficiencies at maximum power of normal-,sub-and super-dissipative Carnot-like heat engines are proved to be bounded between ηc/2 and ηc/ (2-ηc),ηc/2 and ηc,0 and ηc/ (2-ηc),respectively.These bounds are also shared by linear,sub-and super-linear irreversible Carnot-like engines [Tu and Wang,Europhys.Lett.98 (2012) 40001] although the dissipative engines and the irreversible ones are inequivalent to each other.
N Clark
2003-03-01
Full Text Available The aim of this study was to investigate maximum aerobic power (VO2 max and anaerobic threshold (AT as determinants of training status among professional soccer players. Twelve professional 1st team British male soccer players (age: 26.2 ± 3.3 years, height: 1.77 ± 0.05 m, body mass: 79.3 ± 9.4 kg agreed to participate in the study and provided informed consent. All subjects completed a combined test of anaerobic threshold (AT and maximum aerobic power on two occasions: Test 1 following 5 weeks of low level activity at the end of the off-season and Test 2 immediately following conclusion of the competitive season. AT was assessed as both lactate threshold (LT and ventilatory threshold (VT. There was no change in VO2 max between Test 1 and Test 2 (63.3 ± 5.8 ml·kg-1·min-1 vs. 62.1 ± 4.9 ml·kg-1·min-1 respectively, however, the duration of exercise tolerance (ET at VO2 max was significantly extended from Test 1 to Test 2 (204 ± 54 vs. 228 ± 68 s respectively (P<0.01. LT oxygen consumption was significantly improved in Test 2 versus Test 1 (P<0.01 VT was also improved (P<0.05. There was no significant difference in VO2 (ml·kg-1·min-1 corresponding to LT and VT. The results of this study show that VO2 max is a less sensitive indicator to changes in training status in professional soccer players than either LT or VT.
Raynald Labrecque
2009-11-01
Full Text Available It is known that mechanical work, and in turn electricity, can be produced from a difference in the chemical potential that may result from a salinity gradient. Such a gradient may be found, for instance, in an estuary where a stream of soft water is flooding into a sink of salty water which we may find in an ocean, gulf or salt lake. Various technological approaches are proposed for the production of energy from a salinity gradient between a stream of soft water and a source of salty water. Before considering the implementation of a typical technology, it is of utmost importance to be able to compare various technological approaches, on the same basis, using the appropriate variables and mathematical formulations. In this context, exergy balance can become a very useful tool for an easy and quick evaluation of the maximum thermodynamic work that can be produced from energy systems. In this short paper, we briefly introduce the use of exergy for enabling us to easily and quickly assess the theoretical maximum power or ideal reversible work we may expect from typical salinity gradient energy systems.
Technical development of electric power storage system. Development of load conditioner
Tanaka, Toshikatsu
1988-07-01
The load conditioner heightens the utilization ratio of facilities by the stardardization of load for the suppliers and has the consumers advantageously utilize cheap electric power. The domestic facilities are basically composed of charging rectifier, discharging self-exciting inverter and secondary battery. As there presently exists lead battery as a secondary battery, the Electric Power Research Center developed a load conditioner system by using lead battery and is making its operational study. As a secondary lithium battery satisfying the compactness of further particular importance, there are high molecule battery using high molecule compounds such as polyaniline and polyacene, intercaration type battery using vanadium oxide or molybdenum disulfide, etc. Then, in order to materialize the enlargement and life lengthening of those batteries, the steady study of all of negative electrode, positive electrode, electrolyte, battery structure. (3 figs, 2 tabs)
Demand Side Management for Stand-Alone Hybrid Power Systems Based on Load Identification
Friederich Kupzog
2012-11-01
Full Text Available Within the field of Distributed Generation (DG, stand-alone Hybrid Power Systems (HPS are a suitable solution to provide energy to isolated facilities where the connection to a centralized grid is not affordable. The logical evolution of such systems involves the optimization of power resources and related control strategies, but also enhancements concerning the management of energy loads. This paper introduces Demand Side Management (DSM strategies specially designed for HPS. They are applied on a real and patented HPS that consists of PV panels, a diesel generator, an inverter and a set of batteries. DSM strategies are built up on a framework of distributed endpointdevices connected to a central control application where loads are identified according to their behavior. System network components, load definitions, the control application and DSM strategies are depicted. Finally, simulations show illustrative savings achieved by the application of some of the proposed strategies.
MODELING OF WIND LOADS ACTING ON THE WIND POWER STATION CONSTRUCTION OF THE COMBINED TYPE
Bukhtoyarova E. S.
2014-04-01
Full Text Available The article presents the solution of questions about the intensity of wind loads acting on the wind power station of the combined type in relation to the conditions of the Rostov region on the basis of the structural dynamic simulation
del Puerto-Flores, D.; Ortega, R.; Scherpen, J. M. A.
2012-01-01
Recently, it has been established that power factor (PF) improvement for nonlinear loads with nonsinusoidal source voltage is equivalent to imposing the property of cyclodissipativity to the source terminals. Using this framework, the classical capacitor and inductor compensators were interpreted in
Allocation of Power Meters for Online Load Distribution Estimation in Smart Grids
Kouzelis, Konstantinos; Diaz de Cerio Mendaza, Iker; Bak-Jensen, Birgitte
2015-01-01
observability of the load distribution in their grid throughout the day. This paper investigates the possibility of improving the observability by allocating a minimum number of additional online operated power meters in the distribution grid. This allocation, driven by optimisation, clustering, and forecasting...
Controller design for a Wind Farm, Considering both Power and Load Aspects
Soleimanzadeh, Maryam; Wisniewski, Rafal
2011-01-01
turbine. The control algorithm determines the reference signals for each individual wind turbine controller in two scenarios based on low and high wind speed. In low wind speed, the reference signals for rotor speed are adjusted, taking the trade-off between power maximization and load minimization...
A Hybrid Power Control Concept for PV Inverters with Reduced Thermal Loading
Yang, Yongheng; Wang, Huai; Blaabjerg, Frede
2014-01-01
on a single-phase PV inverter under yearly operation is presented with analyses of the thermal loading, lifetime, and annual energy yield. It has revealed the trade-off factors to select the power limit and also verified the feasibility and the effectiveness of the proposed control concept....
Stability Enhancement Based on Virtual Impedance for DC Microgrids with Constant Power Loads
Lu, Xiaonan; Sun, Kai; Guerrero, Josep M.
2015-01-01
the overall stability of the above DC microgrid with constant power loads (CPLs), a comprehensive small-signal model is derived by analyzing the interface converters in each stage. The instability issue induced by the CPLs is revealed by using the criteria of impedance matching. Meanwhile, virtual...
Overloading on Slides: Cognitive Load Theory and Microsoft's Slide Program PowerPoint
Cooper, Elizabeth
2009-01-01
The integration of Microsoft's PowerPoint and other slideware programs into the classroom setting may hinder educational progress rather than help it. An examination of the literature focusing on Cognitive Load Theory recognizes that students' have a limited tolerance for the amount of sights and sounds on display at any given time, especially in…
Mapping Wind Farm Loads and Power Production - A Case Study on Horns Rev 1
Galinos, Christos; Dimitrov, Nikolay; Larsen, Torben J.; Natarajan, Anand; Hansen, Kurt S.
2016-09-01
This paper describes the development of a wind turbine (WT) component lifetime fatigue load variation map within an offshore wind farm. A case study on the offshore wind farm Horns Rev I is conducted with this purpose, by quantifying wake effects using the Dynamic Wake Meandering (DWM) method, which has previously been validated based on CFD, Lidar and full scale load measurements. Fully coupled aeroelastic load simulations using turbulent wind conditions are conducted for all wind directions and mean wind speeds between cut-in and cut-out using site specific turbulence level measurements. Based on the mean wind speed and direction distribution, the representative 20-year lifetime fatigue loads are calculated. It is found that the heaviest loaded WT is not the same when looking at blade root, tower top or tower base components. The blade loads are mainly dominated by the wake situations above rated wind speed and the highest loaded blades are in the easternmost row as the dominating wind direction is from West. Regarding the tower components, the highest loaded WTs are also located towards the eastern central location. The turbines with highest power production are, not surprisingly, the ones facing a free sector towards west and south. The power production results of few turbines are compared with SCADA data. The results of this paper are expected to have significance for operation and maintenance planning, where the schedules for inspection and service activities can be adjusted to the requirements arising from the varying fatigue levels. Furthermore, the results can be used in the context of remaining fatigue lifetime assessment and planning of decommissioning.
Tom, M.; Paul, O.; Galchev, T.
2015-12-01
This paper presents the design and simulation results of a self-starting electrical interface circuit for Parametric Frequency Increased Generator (PFIG) vibrational energy harvesters. A significant challenge with these types of harvesters is the ring down of the transducer, introducing an exponential decrease in efficiency when interfaced with standard passive rectifiers. This work aims to address these challenges by interfacing a standard active rectifier to a buck-boost stage in order to decouple the load and always provide an optimal impedance to the transducer. Because PFIG harvesters have two outputs, an inductor sharing technique allows the hardware to be reused. The active buck-boost power management circuit is designed for XFAB's 0.35 μm 2P5M CMOS process. It can provide an efficiency between 75% - 93% for input voltages in the range of 0.5 - 2 V, reaching its maximum efficiency at 1.8 V. The active power consumption of the power converter is 800 nW. The system can start from as low as 800 mV of input voltage and 3 μW of input power.
Said, Sri Mawar
2015-01-01
Bakaru hydro power plan water resources model will describe a model in anticipating load growth in Sulselbar Power System until year 2030. Bakaru hydro power plan is supplied by Mamasa, Sumarorong, and Lembang watershed, water supply is influenced with rain fall volume, topography condition (steep slope, type of soil, and land use) of a water catchment area. A model is constructed using Fuzzy logic in water water inflow is Y = 0,0687X2 ??? 4,279X + 82,917 and erosion inflow is Y = - 0.0001X2 ...
李鑫; 方陈; 张沛超; 包海龙
2013-01-01
For common maximum power point tracking (MPPT) control methods, the complexities of the structures and the controlling effects cannot be balanced very well. Aiming at this problem, an argumentation about the application of maximum power transmission theorytransfer?theorem in the PV system is discussed and a solution onfrom the view of impedance adaption is presented. According to the conclusion, a new MPPT control algorithm, which has the ability of rapid self-optimization, was proposed. The simulation model of three-phase grid-connected PV power system is established through MATLAB/Simulink. And the experiment is implemented under the circumstances such as? fast changes of external environments and load fluctuation. Comparing the improved control method with some classic ones, the results indicate that the tracking effect of proposed improved impedance adaption algorithm is better.%针对光伏发电系统最大功率点跟踪控制中结构复杂度与控制效果难以兼得的问题,文章从阻抗适配角度论证了最大功率传输理论应用于光伏系统控制的正确性,并提出一种具备快速自寻优能力的光伏系统最大功率点跟踪控制方法.通过Matlab仿真并与常见最大功率点跟踪控制方法相比较,文章所提出的算法具有更好的跟踪效果.
New approaches to provide ride-through for critical loads in electric power distribution systems
Montero-Hernandez, Oscar C.
2001-07-01
The extensive use of electronic circuits has enabled modernization, automation, miniaturization, high quality, low cost, and other achievements regarding electric loads in the last decades. However, modern electronic circuits and systems are extremely sensitive to disturbances from the electric power supply. In fact, the rate at which these disturbances happen is considerable as has been documented in recent years. In response to the power quality concerns presented previously, this dissertation is proposing new approaches to provide ride-through for critical loads during voltage disturbances with emphasis on voltage sags. In this dissertation, a new approach based on an AC-DC-AC system is proposed to provide ride-through for critical loads connected in buildings and/or an industrial system. In this approach, a three-phase IGBT inverter with a built in Dc-link voltage regulator is suitably controlled along with static by-pass switches to provide continuous power to critical loads. During a disturbance, the input utility source is disconnected and the power from the inverter is connected to the load. The remaining voltage in the AC supply is converted to DC and compensated before being applied to the inverter and the load. After detecting normal utility conditions, power from the utility is restored to the critical load. In order to achieve an extended ride-through capability a second approach is introduced. In this case, the Dc-link voltage regulator is performed by a DC-DC Buck-Boost converter. This new approach has the capability to mitigate voltage variations below and above the nominal value. In the third approach presented in this dissertation, a three-phase AC to AC boost converter is investigated. This converter provides a boosting action for the utility input voltages, right before they are applied to the load. The proposed Pulse Width Modulation (PWM) control strategy ensures independent control of each phase and compensates for both single-phase or poly
Zero Power Levitation Control of Hybrid Electro-Magnetic Levitation System by Load Observer
Kim, Youn Hyun; Lee, Ju [Hanyang University, Seoul (Korea)
2001-06-01
This paper introduces the scheme that improve the control performance of electromagnetic levitation system with zero power controller. Magnetic levitation is used widely, but the electromagnetic force has nonlinear characteristics because it is proportioned to a square of the magnetic flux density and it is in inverse proportion to a square of the air gap. So, it is complicate and difficult to control the electromagnetic force. Besides, it is more difficult to control if the equivalent gap is unknown in case of zero power control. Therefore, this paper proposed the hybrid electro-magnetic levitation control method in which the variable load is estimated by using a load observer and its system is controlled at a new zero power equilibrium air gap position. Also it is confirmed that the proposed control method improve the control performance through simulation and experiment. (author). 10 refs., 17 figs., 1 tab.
Multi-timescale modelling for the loading behaviours of power electronics converter
Ma, Ke; Blaabjerg, Frede
2015-01-01
The thermal dynamics of power device, referred as “thermal cycling”, are closely related to the reliability as well as the cost of the power electronics converter. However, the device loading is disturbed by many factors of the converter system which present at various times-constants from micro...... into three modelling levels according to the timescales of the interested thermal dynamics and their disturbances. A series of multi-disciplinary models are then established including the whole set of control, electrical, loss and thermal parts of the converter. It is concluded that, by the proposed multi......-timescales modelling concept and approaches, more complete loading information of power device can be mapped based on the mission profiles of converter, thus it is very helpful for better prediction of converter lifetime and more cost-effective design of the cooling system....
Prakash, S.; Sinha, S. K.
2015-09-01
In this research work, two areas hydro-thermal power system connected through tie-lines is considered. The perturbation of frequencies at the areas and resulting tie line power flows arise due to unpredictable load variations that cause mismatch between the generated and demanded powers. Due to rising and falling power demand, the real and reactive power balance is harmed; hence frequency and voltage get deviated from nominal value. This necessitates designing of an accurate and fast controller to maintain the system parameters at nominal value. The main purpose of system generation control is to balance the system generation against the load and losses so that the desired frequency and power interchange between neighboring systems are maintained. The intelligent controllers like fuzzy logic, artificial neural network (ANN) and hybrid fuzzy neural network approaches are used for automatic generation control for the two area interconnected power systems. Area 1 consists of thermal reheat power plant whereas area 2 consists of hydro power plant with electric governor. Performance evaluation is carried out by using intelligent (ANFIS, ANN and fuzzy) control and conventional PI and PID control approaches. To enhance the performance of controller sliding surface i.e. variable structure control is included. The model of interconnected power system has been developed with all five types of said controllers and simulated using MATLAB/SIMULINK package. The performance of the intelligent controllers has been compared with the conventional PI and PID controllers for the interconnected power system. A comparison of ANFIS, ANN, Fuzzy and PI, PID based approaches shows the superiority of proposed ANFIS over ANN, fuzzy and PI, PID. Thus the hybrid fuzzy neural network controller has better dynamic response i.e., quick in operation, reduced error magnitude and minimized frequency transients.
Power system security enhancement through direct non-disruptive load control
Ramanathan, Badri Narayanan
The transition to a competitive market structure raises significant concerns regarding reliability of the power grid. A need to build tools for security assessment that produce operating limit boundaries for both static and dynamic contingencies is recognized. Besides, an increase in overall uncertainty in operating conditions makes corrective actions at times ineffective leaving the system vulnerable to instability. The tools that are in place for stability enhancement are mostly corrective and suffer from lack of robustness to operating condition changes. They often pose serious coordination challenges. With deregulation, there have also been ownership and responsibility issues associated with stability controls. However, the changing utility business model and the developments in enabling technologies such as two-way communication, metering, and control open up several new possibilities for power system security enhancement. This research proposes preventive modulation of selected loads through direct control for power system security enhancement. Two main contributions of this research are the following: development of an analysis framework and two conceptually different analysis approaches for load modulation to enhance oscillatory stability, and the development and study of algorithms for real-time modulation of thermostatic loads. The underlying analysis framework is based on the Structured Singular Value (SSV or mu) theory. Based on the above framework, two fundamentally different approaches towards analysis of the amount of load modulation for desired stability performance have been developed. Both the approaches have been tested on two different test systems: CIGRE Nordic test system and an equivalent of the Western Electric Coordinating Council test system. This research also develops algorithms for real-time modulation of thermostatic loads that use the results of the analysis. In line with some recent load management programs executed by utilities, two