Level, potential sources of polycyclic aromatic hydrocarbons (PAHs) in particulate matter (PM10) in Naples

Science.gov (United States)

Di Vaio, Paola; Cocozziello, Beatrice; Corvino, Angela; Fiorino, Ferdinando; Frecentese, Francesco; Magli, Elisa; Onorati, Giuseppe; Saccone, Irene; Santagada, Vincenzo; Settimo, Gaetano; Severino, Beatrice; Perissutti, Elisa

2016-03-01

In Naples, particulate matter PM10 associated with polycyclic aromatic hydrocarbons (PAHs) in ambient air were determined in urban background (NA01) and urban traffic (NA02) sites. The principal objective of the study was to determine the concentration and distribution of PAHs in PM10 for identification of their possible sources (through diagnostic ratio - DR and principal component analysis - PCA) and an estimation of the human health risk (from exposure to airborne TEQ). Airborne PM10 samples were collected on quartz filters using a Low Volume Sampler (LVS) for 24 h with seasonal samples (autumn, winter, spring and summer) of about 15 days each between October 2012 and July 2013. The PM10 mass was gravimetrically determined. The PM10 levels, in all seasons, were significantly higher (P gas chromatography-mass spectrometer (GC-MS) analysis. The concentration of Benzo[a]Pyrene, BaP (EU and National limit value: 1 ng m-3 in PM10), varied from 0.065 ng m-3 during autumn time to 0.872 ng m-3 in spring time (NA01) and from 0.120 ng m-3 during autumn time to 1.48 ng m-3 of winter time (NA02) with four overshoots. In NA02 the trend of Σ12 PAHs was comparable to NA01 but were observed higher values than NA01. In fact, the mean concentration of Σ12 PAHs, in urban-traffic site was generally 2 times greater than in urban-background site in all the campaigns. PAHs with 5 and 6 ring, many of which are suspected carcinogens or genotoxic agents, (i.e Benzo[a]Pyrene, Indeno[1,2,3-cd]Pyrene, Benzo[b]Fluoranthene, Benzo[k]Fluoranthene and Benzo[g,h,i]Perylene), had a large contribution (∼50-55%) of total PAHs concentration in PM10 in two sites and in each of the campaigns. Diagnostic ratio analysis and PCA suggested a substantial contributions from traffic emission with minimal influence from coal combustion and natural gas emissions. In particular diesel vehicular emissions were the major source of PAHs at the studied sites. The use of Toxicity Equivalence Quantity (TEQ

Source apportionment of PM10 and PM2.5 in a desert region in northern Chile

International Nuclear Information System (INIS)

Jorquera, Héctor; Barraza, Francisco

2013-01-01

Estimating contributions of anthropogenic sources to ambient particulate matter (PM) in desert regions is a challenging issue because wind erosion contributions are ubiquitous, significant and difficult to quantify by using source-oriented, dispersion models. A receptor modeling analysis has been applied to ambient PM 10 and PM 2.5 measured in an industrial zone ∼ 20 km SE of Antofagasta (23.63°S, 70.39°W), a midsize coastal city in northern Chile; the monitoring site is within a desert region that extends from northern Chile to southern Perú. Integrated 24-hour ambient samples of PM 10 and PM 2.5 were taken with Harvard Impactors; samples were analyzed by X Ray Fluorescence, ionic chromatography (NO 3 − and SO 4 = ), atomic absorption (Na + , K + ) and thermal optical transmission for elemental and organic carbon determination. Receptor modeling was carried out using Positive Matrix Factorization (US EPA Version 3.0); sources were identified by looking at specific tracers, tracer ratios, local winds and wind trajectories computed from NOAA's HYSPLIT model. For the PM 2.5 fraction, six contributions were found — cement plant, 33.7 ± 1.3%; soil dust, 22.4 ± 1.6%; sulfates, 17.8 ± 1.7%; mineral stockpiles and brine plant, 12.4 ± 1.2%; Antofagasta, 8.5 ± 1.3% and copper smelter, 5.3 ± 0.8%. For the PM 10 fraction five sources were identified — cement plant, 38.2 ± 1.5%; soil dust, 31.2 ± 2.3%; mineral stockpiles and brine plant, 12.7 ± 1.7%; copper smelter, 11.5 ± 1.6% and marine aerosol, 6.5 ± 2.4%. Therefore local sources contribute to ambient PM concentrations more than distant sources (Antofagasta, marine aerosol) do. Soil dust is enriched with deposition of marine aerosol and calcium, sulfates and heavy metals from surrounding industrial activities. The mean contribution of suspended soil dust to PM 10 is 50 μg/m 3 and the peak daily value is 104 μg/m 3 . For the PM 2.5 fraction, suspended soil dust contributes with an average of 9.3 �

Preliminary analysis of variability in concentration of fine particulate matter - PM1.0, PM2.5 and PM10 in area of Poznań city

Directory of Open Access Journals (Sweden)

Sówka Izabela

2018-01-01

Full Text Available It is commonly known, that suspended particulate matter pose a threat to human life and health, negatively influence the flora, climate and also materials. Especially dangerous is the presence of high concentration of particulate matter in the area of cities, where density of population is high. The research aimed at determining the variability of suspended particulate matter concentration (PM1.0, PM2.5 and PM10 in two different thermal seasons, in the area of Poznań city. As a part of carried out work we analyzed the variability of concentrations and also performed a preliminary analysis of their correlation. Measured concentrations of particulate matter were contained within following ranges: PM10 – 8.7-69.6 μg/m3, PM2.5 – 2.2-88.5 μg/m3, PM1.0 – 2.5-22.9 μg/m3 in the winter season and 1.0-42.8 μg/m3 (PM10, 1.2-40.3 μg/m3 (PM2.5 and 2.7-10.4 (PM1.0 in the summer season. Preliminary correlative analysis indicated interdependence between the temperature of air, the speed of wind and concentration of particulate matter in selected measurement points. The values of correlation coefficients between the air temperature, speed of wind and concentrations of particulate matter were respectively equal to: for PM10: -0.59 and -0.55 (Jana Pawła II Street, -0.53 and -0.53 (Szymanowskiego Street, for PM2.5: -0.60 and -0.53 (Jana Pawła II Street and for PM1.0 -0.40 and -0.59 (Jana Pawła II Street.

Chemical mass balance source apportionment of fine and PM10 in the Desert Southwest, USA

Directory of Open Access Journals (Sweden)

Andrea L. Clements

2016-03-01

Full Text Available The Desert Southwest Coarse Particulate Matter Study was undertaken in Pinal County, Arizona, to better understand the origin and impact of sources of fine and coarse particulate matter (PM in rural, arid regions of the U.S. southwestern desert. The desert southwest experiences some of the highest PM10 mass concentrations in the country. To augment previously reported results, 6-week aggregated organic speciation data that included ambient concentrations of n-alkanes, polycyclic aromatic hydrocarbons, organic acids, and saccharides were used in chemical mass balance modeling (CMB. A set of re-suspended soil samples were analyzed for specific marker species to provide locally-appropriate source profiles for the CMB analysis. These profiles, as well as previously collected plant and fungal spore profiles from the region, were combined with published source profiles for other relevant sources and used in the CMB analysis. The six new region-specific source profiles included both organic and inorganic species for four crustal material sources, one plant detritus source, and one fungal spore source.Results indicate that up to half of the ambient PM2.5 was apportioned to motor vehicles with the highest regional contribution observed in the small urban center of Casa Grande. Daily levels of apportioned crustal material accounted for up to 50% of PM2.5 mass with the highest contributions observed at the sites closest to active agricultural areas. Apportioned secondary PM, biomass burning, and road dust typically contributed less than 35% as a group to the apportioned PM2.5 mass. Crustal material was the primary source apportioned to PM10 and accounted for between 50–90% of the apportioned mass. Of the other sources apportioned to PM10, motor vehicles and road dust were the largest contributors at the urban and one of the rural sites, whereas road dust and meat cooking operations were the largest contributors at the other rural site.

Danish emission inventory for particular matter (PM)

Energy Technology Data Exchange (ETDEWEB)

Nielsen, M; Winther, M; Illerup, J B; Hjort Mikkelsen, M

2003-11-01

The first Danish emission inventory that was reported in 2002 was a provisional-estimate based on data presently available. This report documents methodology, emission factors and references used for an improved Danish emission inventory for particulate matter. Further results of the improved emission inventory for the year 2000 are shown. The particulate matter emission inventory includes TSP, PM,, and PM, The report covers emission inventories for transport and stationary combustion. An appendix covering emissions from agriculture is also included. For the transport sector, both exhaust and non-exhaust emission such as tyre and break wear and road abrasion are included. (au)

Source apportionment of PM2.5 across China using LOTOS-EUROS

NARCIS (Netherlands)

Timmermans, R.; Kranenburg, R.; Manders, A.; Hendriks, C.; Segers, A.; Dammers, E.; Denier van der Gon, H.; Schaap, M.; Dammers, E.; Zhang, Q.; Wang, L.; Liu, Z.

2017-01-01

China's population is exposed to high levels of particulate matter (PM) due to its strong economic growth and associated urbanization and industrialization. To support policy makers to develop cost effective mitigation strategies it is of crucial importance to understand the emission sources as well

Source apportionment of PM2.5 in North India using source-oriented air quality models

International Nuclear Information System (INIS)

Guo, Hao; Kota, Sri Harsha; Sahu, Shovan Kumar; Hu, Jianlin; Ying, Qi; Gao, Aifang; Zhang, Hongliang

2017-01-01

In recent years, severe pollution events were observed frequently in India especially at its capital, New Delhi. However, limited studies have been conducted to understand the sources to high pollutant concentrations for designing effective control strategies. In this work, source-oriented versions of the Community Multi-scale Air Quality (CMAQ) model with Emissions Database for Global Atmospheric Research (EDGAR) were applied to quantify the contributions of eight source types (energy, industry, residential, on-road, off-road, agriculture, open burning and dust) to fine particulate matter (PM 2.5 ) and its components including primary PM (PPM) and secondary inorganic aerosol (SIA) i.e. sulfate, nitrate and ammonium ions, in Delhi and three surrounding cities, Chandigarh, Lucknow and Jaipur in 2015. PPM mass is dominated by industry and residential activities (>60%). Energy (∼39%) and industry (∼45%) sectors contribute significantly to PPM at south of Delhi, which reach a maximum of 200 μg/m 3 during winter. Unlike PPM, SIA concentrations from different sources are more heterogeneous. High SIA concentrations (∼25 μg/m 3 ) at south Delhi and central Uttar Pradesh were mainly attributed to energy, industry and residential sectors. Agriculture is more important for SIA than PPM and contributions of on-road and open burning to SIA are also higher than to PPM. Residential sector contributes highest to total PM 2.5 (∼80 μg/m 3 ), followed by industry (∼70 μg/m 3 ) in North India. Energy and agriculture contribute ∼25 μg/m 3 and ∼16 μg/m 3 to total PM 2.5 , while SOA contributes <5 μg/m 3 . In Delhi, industry and residential activities contribute to 80% of total PM 2.5 . - Highlights: • Sources of PM 2.5 in North India were quantified by source-oriented CMAQ. • Industrial/residential activities are the dominating sources (60–70%) for PPM. • Energy/agriculture are the most important sources (30–40%) for SIA. • Strong seasonal

Source strengths for indoor human activities that resuspend particulate matter.

Science.gov (United States)

Ferro, Andrea R; Kopperud, Royal J; Hildemann, Lynn M

2004-03-15

A mathematical model was applied to continuous indoor and outdoor particulate matter (PM) measurements to estimate source strengths for a variety of prescribed human activities that resuspend house dust in the home. Activities included folding blankets, folding clothes, dry dusting, making a bed, dancing on a rug, dancing on a wood floor, vacuuming, and walking around and sitting on upholstered furniture. Although most of the resuspended particle mass from these activities was larger than 5 microm in diameter, the resuspension of PM2.5 and PM5 was substantial, with source strengths ranging from 0.03 to 0.5 mg min(-1) for PM2.5 and from 0.1 to 1.4 mg min(-1) for PM5. Source strengths for PM > 5 microm could not be quantified due to instrument limitations. The source strengths were found to be a function of the number of persons performing the activity, the vigor of the activity, the type of activity, and the type of flooring.

Source Sector and Region Contributions to BC and PM2.5 in Central Asia

Science.gov (United States)

Particulate matter (PM) mass concentrations, seasonal cycles, source sector and source region contributions in Central Asia (CA) are analyzed for the period April 2008-July 2009 using the STEM chemical transport model and modeled meteorology from the WRF model. Predicted AOD valu...

Source apportionment studies on particulate matter in Beijing/China

Science.gov (United States)

Suppan, P.; Shen, R.; Shao, L.; Schrader, S.; Schäfer, K.; Norra, S.; Vogel, B.; Cen, K.; Wang, Y.

2013-05-01

More than 15 million people in the greater area of Beijing are still suffering from severe air pollution levels caused by sources within the city itself but also from external impacts like severe dust storms and long range advection from the southern and central part of China. Within this context particulate matter (PM) is the major air pollutant in the greater area of Beijing (Garland et al., 2009). PM did not serve only as lead substance for air quality levels and therefore for adverse health impact effects but also for a strong influence on the climate system by changing e.g. the radiative balance. Investigations on emission reductions during the Olympic Summer Games in 2008 have caused a strong reduction on coarser particles (PM10) but not on smaller particles (PM2.5). In order to discriminate the composition of the particulate matter levels, the different behavior of coarser and smaller particles investigations on source attribution, particle characteristics and external impacts on the PM levels of the city of Beijing by measurements and modeling are performed: a) Examples of long term measurements of PM2.5 filter sampling in 2010/2011 with the objectives of detailed chemical (source attribution, carbon fraction, organic speciation and inorganic composition) and isotopic analyses as well as toxicological assessment in cooperation with several institutions (Karlsruhe Institute of Technology (IfGG/IMG), Helmholtz Zentrum München (HMGU), University Rostock (UR), Chinese University of Mining and Technology Beijing, CUMTB) will be discussed. b) The impact of dust storm events on the overall pollution level of particulate matter in the greater area of Beijing is being assessed by the online coupled comprehensive model system COSMO-ART. First results of the dust storm modeling in northern China (2011, April 30th) demonstrates very well the general behavior of the meteorological parameters temperature and humidity as well as a good agreement between modeled and

Urban PM in Eastern Germany: Source apportionment and contributions from different spatial scales

Science.gov (United States)

van Pinxteren, D.; Fomba, K. W.; Mothes, F.; Spindler, G.; Herrmann, H.

2017-12-01

Understanding the contributions of particulate matter (PM) sources and the source areas impacting total PM levels in a city are important requirements for further developing clean air policies and efficient abatement strategies. This presentation reports on two studies in Eastern Germany providing a detailed picture of present-day urban PM sources and discriminating contributions of local, regional and long-range sources. The "Leipzig Aerosol 2013-15" study yielded contributions of 12 sources to coarse, fine, and ultrafine particles, resolved by Positive Matrix Factorization (PMF) from comprehensive chemical speciation of 5-stage Berner impactor samples at 4 different sites in the Leipzig area. Dominant winter-time sources were traffic exhaust and non-exhaust emissions, secondary aerosol formation, and combustion emissions from both biomass and coal burning with different relative importance in different particle size ranges. Local sources dominated PM levels in ultrafine and coarse particles (60% - 80%) while high mass concentrations in accumulation mode particles mainly resulted from regional import into the city (70%). The "PM-East" study compiled PM10 mass and constituents' concentrations at 10 urban and rural sites in Eastern Germany during winter 2016/17, which included a 3-week episode of frequent exceedances of the PM10 limit value. PMF source apportionment is performed for a subset of the sites, including the city of Berlin. Contributions from short-, mid-, and long-range sources, including trans-boundary pollution import from neighbouring countries, are quantitatively assessed by advanced back trajectory statistical methods. Data analysis in PM-East is ongoing and final results will be available by November. Funding is acknowledged from 4 federal states of Germany: Berlin Senate Department for Environment, Transport and Climate Protection; Saxon State Office for Environment, Agriculture and Geology; State Agency for Environment, Nature Conservation and

Source sector and region contributions to BC and PM2.5 in Central Asia

NARCIS (Netherlands)

Kulkarni, S.; Sobhani, N.; Miller-Schulze, J.P.; Shafer, M.M.; Schauer, J.J.; Solomon, P.A.; Saide, P.E.; Spak, S.N.; Cheng, Y.F.; Denier Van Der Gon, H.A.C.; Lu, Z.; Streets, D.G.; Janssens-Maenhout, G.; Wiedinmyer, C.; Lantz, J.; Artamonova, M.; Chen, B.; Imashev, S.; Sverdlik, L.; Deminter, J.T.; Adhikary, B.; D'Allura, A.; Wei, C.; Carmichael, G.R.

2015-01-01

Particulate matter (PM) mass concentrations, seasonal cycles, source sector, and source region contributions in Central Asia (CA) are analyzed for the period April 2008-July 2009 using the Sulfur Transport and dEposition Model (STEM) chemical transport model and modeled meteorology from the Weather

A systematic analysis of PM2.5 in Beijing and its sources from 2000 to 2012

Science.gov (United States)

Lv, Baolei; Zhang, Bin; Bai, Yuqi

2016-01-01

Particulate matter with an aerodynamic diameter of 2.5 μm or less (PM2.5) is the main air pollutant in Beijing. To have a comprehensive understanding of concentrations, compositions and sources of PM2.5 in Beijing, recent studies reporting ground-based observations and source apportionment results dated from 2000 to 2012 in this typical large city of China are reviewed. Statistical methods were also used to better enable data comparison. During the last decade, annual average concentrations of PM2.5 have decreased and seasonal mean concentrations declined through autumn and winter. Generally, winter is the most polluted season and summer is the least polluted one. Seasonal variance of PM2.5 levels decreased. For diurnal variance, PM2.5 generally increases at night and decreases during the day. On average, organic matters, sulfate, nitrate and ammonium are the major compositions of PM2.5 in Beijing. Fractions of organic matters increased from 2000 to 2004, and decreased afterwards. Fractions of sulfate, nitrate and ammonium decreased in winter and remained largely unchanged in summer. Concentrations of organic carbon and elemental carbon were always higher in winter than in summer and they barely changed during the last decade. Concentrations of sulfate, nitrate and ammonium exhibited significant increasing trend in summer but in reverse in winter. On average they were higher in winter than in summer before 2005, and took a reverse after 2005. Receptor model results show that vehicle, dust, industry, biomass burning, coal combustion and secondary products were major sources and they all increased except coal combustions and secondary products. The growth was decided both changing social and economic activities in Beijing, and most likely growing emissions in neighboring Hebei province. Explicit descriptions of the spatial variations of PM2.5 concentration, better methods to estimate secondary products and ensemble source apportionments models to reduce

Particulate Matter Dispersion (PM10, with interrelation of topographic and meteorological factors

Directory of Open Access Journals (Sweden)

Alvaro Javier Arrieta-Fuentes

2016-07-01

Full Text Available Mining-industrial processes carried out by anthropic action, bring the generation of impacts to the environment. Between the impacts associated with mining is the involvement of the air quality produced by the release of atmospheric pollutants, being subject to study the behavior of the respirable fraction of particulate matter less than 10 microns (PM10 with respect to meteorological and topographical factors. The analyzed scenarios in the study involved daily and annual exposure times of PM10, in wich modeling with AERMOD View Software was made. The model was carried out in two topographic zones, a complex area, located in the municipality of Socha and a simple area located in the municipality of Sogamoso. It was used meteorological data type satellite, in format .SAM for modeled areas. Three types of emission sources were identified in the areas; considering that the disperse fixed emission sources predominate, followed by the mobile sources and point sources were found in low proportion. PM10 dispersion models made for the zones of simple and complex topography, gave as result that direction and the wind speed is conditioned by the type of zone. It allowed a free flow in the predominant direction in wind rose to the area of simple topography and a turbulent flow in the complex area. It was determined that the sources of emission of PM10 in both cases are local scale; They presented a critical radius of drag and deposition of particles of 200 m approximately.

Receptor modeling studies for the characterization of PM10 pollution sources in Belgrade

Directory of Open Access Journals (Sweden)

Mijić Zoran

2012-01-01

Full Text Available The objective of this study is to determine the major sources and potential source regions of PM10 over Belgrade, Serbia. The PM10 samples were collected from July 2003 to December 2006 in very urban area of Belgrade and concentrations of Al, V, Cr, Mn, Fe, Ni, Cu, Zn, Cd and Pb were analyzed by atomic absorption spectrometry. The analysis of seasonal variations of PM10 mass and some element concentrations reported relatively higher concentrations in winter, what underlined the importance of local emission sources. The Unmix model was used for source apportionment purpose and the four main source profiles (fossil fuel combustion; traffic exhaust/regional transport from industrial centers; traffic related particles/site specific sources and mineral/crustal matter were identified. Among the resolved factors the fossil fuel combustion was the highest contributor (34% followed by traffic/regional industry (26%. Conditional probability function (CPF results identified possible directions of local sources. The potential source contribution function (PSCF and concentration weighted trajectory (CWT receptor models were used to identify spatial source distribution and contribution of regional-scale transported aerosols. [Projekat Ministarstva nauke Republike Srbije, br. III43007 i br. III41011

Chemical composition and sources of PM1 and PM2.5 in Beijing in autumn.

Science.gov (United States)

Zhang, Yanyun; Lang, Jianlei; Cheng, Shuiyuan; Li, Shengyue; Zhou, Ying; Chen, Dongsheng; Zhang, Hanyu; Wang, Haiyan

2018-02-20

Beijing, the capital of China, suffers from severe atmospheric aerosol pollution; nevertheless, a comprehensive study of the constituents and sources of PM 1 is still lacking, and the differences between PM 1 and PM 2.5 are still unclear. In this study, an intensive observation was conducted to reveal the pollution characteristics of PM 1 and PM 2.5 in Beijing in autumn. Positive matrix factorization (PMF), backward trajectories and a potential source contribution function (PSCF) model were used to identify the source categories and source areas of PM 1 and PM 2.5 . The results showed that the average concentrations of PM 1 and PM 2.5 reached 78.20μg/m 3 and 95.47μg/m 3 during the study period, respectively. PM 1 contributed greatly to PM 2.5 . The PM 1 /PM 2.5 value increased from 73.6% to 90.1% with PM 1 concentration growing from 150μg/m 3 . Higher secondary inorganic aerosol (SIA) proportions (31.3%-70.8%) were found in PM 1 . The higher fraction of SIA, OC, EC and typical elements in PM 1 illustrated that anthropogenic components accumulated more in smaller size particles. Three typical weather patterns causing the heavy pollution in autumn were found as follows: (1) Siberian high and uniform high pressure field, (2) cold front and low-voltage system, and (3) uniform low pressure field. A PMF analysis indicated that secondary aerosols and coal combustion, vehicle, industry, biomass burning, and dust were the important sources of PM, accounting for 53.8%, 8.0%, 13.0%, 13.2% and 12.0% of PM 1 , respectively, and for 47.5%, 9.9%, 12.4%, 8.4% and 21.8% of PM 2.5 , respectively. The HYSPLIT and chemical components analysis indicated the potential contribution from biomass burning and fertilization ammonia emissions to PM 1 in autumn. The source areas were similar for PM 1 and PM 1-2.5 under general polluted conditions, but during the heavily polluted periods, the source areas were distributed in farther regions from Beijing for PM 1 than for PM 1-2.5 . Copyright

Potential Sources and Formations of the PM2.5 Pollution in Urban Hangzhou

Directory of Open Access Journals (Sweden)

Jian Wu

2016-07-01

Full Text Available Continuous measurements of meteorological parameters, gaseous pollutants, particulate matters, and the major chemical species in PM2.5 were conducted in urban Hangzhou from 1 September to 30 November 2013 to study the potential sources and formations of PM2.5 pollution. The average PM2.5 concentration was 69 µg·m−3, ~97% higher than the annual concentration limit in the national ambient air quality standards (NAAQS of China. Relative humidity (RH and wind speed (WS were two important factors responsible for the increase of PM2.5 concentration, with the highest value observed under RH of 70%–90%. PM2.5 was in good correlation with both NO2 and CO, but not with SO2, and the potential source contribution function (PSCF results displayed that local emissions were important potential sources contributing to the elevated PM2.5 and NO2 in Hangzhou. Thus, local vehicle emission was suggested as a major contribution to the PM2.5 pollution. Concentrations of NO2 and CO significantly increased in pollution episodes, while the SO2 concentration even decreased, implying local emission rather than region transport was the major source contributing to the formation of pollution episodes. The sum of SO42−, NO3−, and NH4+ accounted for ~50% of PM2.5 in mass in pollution episodes and the NO3−/EC ratios were significantly elevated, revealing that the formation of secondary inorganic species, particularly NO3−, was an important contributor to the PM2.5 pollution in Hangzhou. This study highlights that controlling local pollution emissions was essential to reduce the PM2.5 pollution in Hangzhou, and the control of vehicle emission in particular should be further promoted in the future.

Source identification of ambient PM2.5 during summer inhalation exposure studies in Detroit, MI

Energy Technology Data Exchange (ETDEWEB)

Morishita, M.; Keeler, G.J.; Wagner, J.G.; Harkema, J.R. [University of Michigan, Ann Arbor, MI (United States). Air Quality Laboratory

2006-07-15

Particulate air pollution is associated with cardiopulmonary morbidity and mortality in heavily populated urban centers of the United States. Because ambient fine particulate matter (aerodynamic diameter {<=} 2.5 {mu}m; PM2.5) is a complex mixture resulting from multiple sources and variable atmospheric conditions, it is difficult to identify specific components of PM2.5 that are responsible for adverse health effects. During four consecutive summers from 2000 to 2003 we characterized the ambient gaseous and PM2.5 air quality in an urban southwest Detroit community where childhood asthma hospitalization rates are more than twice the statewide average. Both integrated and continuous PM measurements together with gaseous air pollution measurements were performed using a mobile air research facility, AirCARE1, in which concurrent toxicological studies were being conducted. Chemical and physical characterizations of PM2.5 as well as receptor modeling using positive matrix factorization (PMF) were completed. Results from PMF indicated that six major sources contributed to the observed ambient PM2.5 mass during the summer months. Primary sources included (1) coal combustion/secondary sulfate aerosol, (2) motor vehicle/urban road dust, (3) municipal waste incinerators, (4) oil combustion/refineries, (5) sewage sludge incinerators, and (6) iron/steel manufacturing. Although the contribution of the coal/secondary sulfate aerosol source was greater than other factors, increased levels of urban PM2.5 from local combustion sources were also observed. In addition to characterization of ambient PM2.5 and their sources in southwest Detroit, this paper discusses possible associations of ambient PM2.5 from local combustion sources, specifically incinerator and refinery emissions and the observed adverse health effects during the inhalation exposure campaigns.

Monitoring of PM10 and PM2.5 around primary particulate anthropogenic emission sources

Science.gov (United States)

Querol, Xavier; Alastuey, Andrés; Rodriguez, Sergio; Plana, Felicià; Mantilla, Enrique; Ruiz, Carmen R.

Investigations on the monitoring of ambient air levels of atmospheric particulates were developed around a large source of primary anthropogenic particulate emissions: the industrial ceramic area in the province of Castelló (Eastern Spain). Although these primary particulate emissions have a coarse grain-size distribution, the atmospheric transport dominated by the breeze circulation accounts for a grain-size segregation, which results in ambient air particles occurring mainly in the 2.5-10 μm range. The chemical composition of the ceramic particulate emissions is very similar to the crustal end-member but the use of high Al, Ti and Fe as tracer elements as well as a peculiar grain-size distribution in the insoluble major phases allow us to identify the ceramic input in the bulk particulate matter. PM2.5 instead of PM10 monitoring may avoid the interference of crustal particles without a major reduction in the secondary anthropogenic load, with the exception of nitrate. However, a methodology based in PM2.5 measurement alone is not adequate for monitoring the impact of primary particulate emissions (such as ceramic emissions) on air quality, since the major ambient air particles derived from these emissions are mainly in the range of 2.5-10 μm. Consequently, in areas characterised by major secondary particulate emissions, PM2.5 monitoring should detect anthropogenic particulate pollutants without crustal particulate interference, whereas PM10 measurements should be used in areas with major primary anthropogenic particulate emissions.

Influence of background particulate matter (PM) on urban air quality in the Pacific Northwest.

Science.gov (United States)

Timonen, H; Wigder, N; Jaffe, D

2013-11-15

Elevated particulate matter concentrations due to Asian long-range transport (LRT) are frequently observed in the free troposphere (FT) above the Pacific Northwest, U.S. Transport of this aerosol from the FT to the boundary layer (BL) and its effect to local air quality remain poorly constrained. We used data collected at the Mount Bachelor observatory (MBO, 2.8 km a.s.l) and from ground stations in the Pacific Northwest to study transport of fine particulate matter (PM) from the FT to the BL. During Asian LRT episodes PM concentrations were clearly elevated above the corresponding monthly averages at MBO as well as at low elevation sites across Washington and Oregon. Also, a clear correlation between MBO and low elevation sites was observed, indicating that LRT episodes are seen in both the FT and BL. In addition, drum impactor measurements show that the chemical composition of PM at MBO was similar to that measured at the BL sites. Using a simple regression model, we estimate that during springtime, when the transport from Asia is most effective, the contribution of Asian sources to PM2.5 in clean background areas of the Pacific Northwest was on average 1.7 μg m(-3) (representing approximately 50-80% of PM). The influence of LRT PM was also seen in measurement stations situated in the urban and urban background areas. However, the fraction of LRT PM was less pronounced (36-50% of PM) due to larger local emissions in the urban areas. Copyright © 2013 Elsevier Ltd. All rights reserved.

Identification of the sources of PM10 in a subway tunnel using positive matrix factorization.

Science.gov (United States)

Park, Duckshin; Lee, Taejeong; Hwang, Doyeon; Jung, Wonseok; Lee, Yongil; Cho, KiChul; Kim, Dongsool; Lees, Kiyoung

2014-12-01

The level of particulate matter of less than 10 μm diameter (PM10) at subway platforms can be significantly reduced by installing a platform screen-door system. However, both workers and passengers might be exposed to higher PM10 levels while the cars are within the tunnel because it is a more confined environment. This study determined the PM10 levels in a subway tunnel, and identified the sources of PM10 using elemental analysis and receptor modeling. Forty-four PM10 samples were collected in the tunnel between the Gireum and Mia stations on Line 4 in metropolitan Seoul and analyzed using inductively coupled plasma-atomic emission spectrometry and ion chromatography. The major PM10 sources were identified using positive matrix factorization (PMF). The average PM10 concentration in the tunnels was 200.8 ± 22.0 μg/m3. Elemental analysis indicated that the PM10 consisted of 40.4% inorganic species, 9.1% anions, 4.9% cations, and 45.6% other materials. Iron was the most abundant element, with an average concentration of 72.5 ± 10.4 μg/m3. The PM10 sources characterized by PMF included rail, wheel, and brake wear (59.6%), soil combustion (17.0%), secondary aerosols (10.0%), electric cable wear (8.1%), and soil and road dust (5.4%). Internal sources comprising rail, wheel, brake, and electric cable wear made the greatest contribution to the PM10 (67.7%) in tunnel air. Implications: With installation of a platform screen door, PM10 levels in subway tunnels were higher than those on platforms. Tunnel PM10 levels exceeded 150 µg/m3 of the Korean standard for subway platform. Elemental analysis of PM10 in a tunnel showed that Fe was the most abundant element. Five PM10 sources in tunnel were identified by positive matrix factorization. Railroad-related sources contributed 68% of PM10 in the subway tunnel.

Source profiles and contributions of biofuel combustion for PM2.5, PM10 and their compositions, in a city influenced by biofuel stoves.

Science.gov (United States)

Tian, Ying-Ze; Chen, Jia-Bao; Zhang, Lin-Lin; Du, Xin; Wei, Jin-Jin; Fan, Hui; Xu, Jiao; Wang, Hai-Ting; Guan, Liao; Shi, Guo-Liang; Feng, Yin-Chang

2017-12-01

Source and ambient samples were collected in a city in China that uses considerable biofuel, to assess influence of biofuel combustion and other sources on particulate matter (PM). Profiles and size distribution of biofuel combustion were investigated. Higher levels in source profiles, a significant increase in heavy-biomass ambient and stronger correlations of K + , Cl - , OC and EC suggest that they can be tracers of biofuel combustion. And char-EC/soot-EC (8.5 for PM 2.5 and 15.8 for PM 10 of source samples) can also be used to distinguish it. In source samples, water-soluble organic carbon (WSOC) were approximately 28.0%-68.8% (PM 2.5 ) and 27.2%-43.8% (PM 10 ) of OC. For size distribution, biofuel combustion mainly produces smaller particles. OC1, OC2, EC1 and EC2 abundances showed two peaks with one below 1 μm and one above 2 μm. An advanced three-way factory analysis model was applied to quantify source contributions to ambient PM 2.5 and PM 10 . Higher contributions of coal combustion, vehicular emission, nitrate and biofuel combustion occurred during the heavy-biomass period, and higher contributions of sulfate and crustal dust were observed during the light-biomass period. Mass and percentage contributions of biofuel combustion were significantly higher in heavy-biomass period. The biofuel combustion attributed above 45% of K + and Cl - , above 30% of EC and about 20% of OC. In addition, through analysis of source profiles and contributions, they were consistently evident that biofuel combustion and crustal dust contributed more to cation than to anion, while sulfate & SOC and nitrate showed stronger influence on anion than on cation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Spatiotemporal patterns of particulate matter (PM and associations between PM and mortality in Shenzhen, China

Directory of Open Access Journals (Sweden)

Fengying Zhang

2016-03-01

Full Text Available Abstract Background Most studies on air pollution exposure and its associations with human health in China have focused on the heavily polluted industrial areas and/or mega-cities, and studies on cities with comparatively low air pollutant concentrations are still rare. Only a few studies have attempted to analyse particulate matter (PM for the vibrant economic centre Shenzhen in the Pearl River Delta. So far no systematic investigation of PM spatiotemporal patterns in Shenzhen has been undertaken and the understanding of pollution exposure in urban agglomerations with comparatively low pollution is still limited. Methods We analyze daily and hourly particulate matter concentrations and all-cause mortality during 2013 in Shenzhen, China. Temporal patterns of PM (PM2.5 and PM10 with aerodynamic diameters of 2.5 (10 μm or less (or less (including particles with a diameter that equals to 2.5 (10 μm are studied, along with the ratio of PM2.5 to PM10. Spatial distributions of PM10 and PM2.5 are addressed and associations of PM10 or PM2.5 and all-cause mortality are analyzed. Results Annual average PM10 and PM2.5 concentrations were 61.3 and 39.6 μg/m3 in 2013. PM2.5 failed to meet the Class 2 annual limit of the National Ambient Air Quality Standard. PM2.5 was the primary air pollutant, with 8.8 % of days having heavy PM2.5 pollution. The daily PM2.5/PM10 ratios were high. Hourly PM2.5 concentrations in the tourist area were lower than downtown throughout the day. PM10 and PM2.5 concentrations were higher in western parts of Shenzhen than in eastern parts. Excess risks in the number of all-cause mortality with a 10 μg/m3 increase of PM were 0.61 % (95 % confidence interval [CI]: 0.50–0.72 for PM10, and 0.69 % (95 % CI: 0.55–0.83 for PM2.5, respectively. The greatest ERs of PM10 and PM2.5 were in 2-day cumulative measures for the all-cause mortality, 2-day lag for females and the young (0–65 years, and L02 for males and the elder (>65

Magnetic properties of atmospheric particulate matter from automatic air sampler stations in Latium (Italy): Toward a definition of magnetic fingerprints for natural and anthropogenic PM10 sources

Science.gov (United States)

Sagnotti, Leonardo; Macrı, Patrizia; Egli, Ramon; Mondino, Manlio

2006-12-01

Environmental problems linked to the concentration of atmospheric particulate matter with dimensions less than 10 μm (PM10) in urban settings have stimulated a variety of scientific researches. This study reports a systematic analysis of the magnetic properties of PM10 samples collected by six automatic stations installed for air quality monitoring through the Latium Region (Italy). We measured the low-field magnetic susceptibility of daily air filters collected during the period July 2004 to July 2005. For each station, we derived an empirical linear correlation linking magnetic susceptibility to the concentration of PM10 produced by local sources (i.e., in absence of significant inputs of exogenous dust). An experimental approach is suggested for estimating the percentage of nonmagnetic PM10 transported from natural far-sided sources (i.e., dust from North Africa and marine aerosols). Moreover, we carried out a variety of additional magnetic measurements to investigate the magnetic mineralogy of selected air filters spanning representative periods. The results indicate that the magnetic fraction of PM10 is composed by a mixture of low-coercivity, magnetite-like, ferrimagnetic particles with a wide spectrum of grain sizes, related to a variety of natural and anthropogenic sources. The natural component of PM10 has a characteristic magnetic signature that is indistinguishable from that of eolian dust. The anthropogenic PM10 fraction is mostly originated from circulating vehicles and is a mixture of prevailing fine superparamagnetic particles and subordinate large multidomain grains; the former are more directly related to exhaust, whereas the latter may be associated to abrasion of metallic parts.

Source apportionment of PM2.5 at the Lin'an regional background site in China with three receptor models

Science.gov (United States)

Deng, Junjun; Zhang, Yanru; Qiu, Yuqing; Zhang, Hongliang; Du, Wenjiao; Xu, Lingling; Hong, Youwei; Chen, Yanting; Chen, Jinsheng

2018-04-01

Source apportionment of fine particulate matter (PM2.5) were conducted at the Lin'an Regional Atmospheric Background Station (LA) in the Yangtze River Delta (YRD) region in China from July 2014 to April 2015 with three receptor models including principal component analysis combining multiple linear regression (PCA-MLR), UNMIX and Positive Matrix Factorization (PMF). The model performance, source identification and source contribution of the three models were analyzed and inter-compared. Source apportionment of PM2.5 was also conducted with the receptor models. Good correlations between the reconstructed and measured concentrations of PM2.5 and its major chemical species were obtained for all models. PMF resolved almost all masses of PM2.5, while PCA-MLR and UNMIX explained about 80%. Five, four and seven sources were identified by PCA-MLR, UNMIX and PMF, respectively. Combustion, secondary source, marine source, dust and industrial activities were identified by all the three receptor models. Combustion source and secondary source were the major sources, and totally contributed over 60% to PM2.5. The PMF model had a better performance on separating the different combustion sources. These findings improve the understanding of PM2.5 sources in background region.

Source Apportionment of Primary and Secondary Fine Particulate Matter in China

Science.gov (United States)

Hu, J.; Zhang, H.; Ying, Q.

2015-12-01

In the past few decades, China have been facing extreme particulate matter (PM) pollution problems due to the combination of fast increase of population, industrialization, urbanization and associated energy consumption and lagging of sufficient emission control measures. Studies have identified the major components of fine PM (PM2.5) in China include primary PM (which is directly emitted into the atmosphere), sulfate and nitrate (which are mainly secondary PM, i.e., formed from gaseous precursors), and organic aerosols (which can be primary or secondary). Contributions of different source sectors to the different PM components are substantially different; therefore source apportionment of these components can provide critical information needed for policy makers to design effective emission control strategies. In the current study, a source-oriented version of the Community Multiscale Air Quality (CMAQ) model that directly tracks the contributions from multiple emission sources to primary and secondary PM2.5 is developed, and then applied to determine the regional contributions of power, industry, transportation and residential sectors to primary PM, nitrate and sulfate concentrations in China. Four months in 2012-2013 are simulated to predict the seasonal variations of source contributions. Model predictions are evaluated with ambient measured concentrations. The source-oriented CMAQ model is capable of reproducing most of the available PM10 and PM2.5 mass, and PM2.5 EC, POC, nitrate and sulfate observations. Predicted source contributions for EC also generally agree with to the source contributions estimated by receptor models reported in previous studies. Model predictions suggest residential is a major contributor to primary PM (30-70%) in the spring and winter, and industrial contributes 40-60% of primary PM in the summer and fall; Transportation is an important source for EC (20-30%); Power sector is the dominating source of nitrate and sulfate in both

Secondary organic carbon quantification and source apportionment of PM10 in Kaifeng, China

Institute of Scientific and Technical Information of China (English)

WU Lin; FENG Yinchang; WU Jianhui; ZHU Tan; BI Xiaohui; HAN Bo; YANG Weihong; YANG Zhiqiang

2009-01-01

During 2005, the filter samples of ambient PM10 from five sites and the source samples of particulate matter were collected in Kaifeng, Henan province of China. Nineteen elements, water-soluble ions, total carbon (TC) and organic carbon (OC) contained in samples were analyzed. Seven contributive source types were identified and their contributions to ambient PM10 were estimated by chemical mass balance (CMB) receptor model. Weak associations between the concentrations of organic carbon and element carbon (EC) were observed during the sampling periods, indicating that there was secondary organic aerosol pollution in the urban atmosphere. An indirect method of "OC/EC minimum ratio" was applied to estimate the concentration of secondary organic carbon (SOC). The results showed that SOC contributed 26.2%, 32.4% and 18.0% of TC in spring, summer-fall and winter respectively, and the annual average SOC concentration was 7.07 μg/m3, accounting for 5.73% of the total mass in ambient PM10. The carbon species concentrations in ambient PM10 were recalculated by subtracting the SOC concentrations from measured concentrations of TC and OC to increase the compatibility of source and receptor measurements for CMB model.

Source apportionment of fine particulate matter in China in 2013 using a source-oriented chemical transport model.

Science.gov (United States)

Shi, Zhihao; Li, Jingyi; Huang, Lin; Wang, Peng; Wu, Li; Ying, Qi; Zhang, Hongliang; Lu, Li; Liu, Xuejun; Liao, Hong; Hu, Jianlin

2017-12-01

China has been suffering high levels of fine particulate matter (PM 2.5 ). Designing effective PM 2.5 control strategies requires information about the contributions of different sources. In this study, a source-oriented Community Multiscale Air Quality (CMAQ) model was applied to quantitatively estimate the contributions of different source sectors to PM 2.5 in China. Emissions of primary PM 2.5 and gas pollutants of SO 2 , NO x , and NH 3 , which are precursors of particulate sulfate, nitrate, and ammonium (SNA, major PM 2.5 components in China), from eight source categories (power plants, residential sources, industries, transportation, open burning, sea salt, windblown dust and agriculture) were separately tracked to determine their contributions to PM 2.5 in 2013. Industrial sector is the largest source of SNA in Beijing, Xi'an and Chongqing, followed by agriculture and power plants. Residential emissions are also important sources of SNA, especially in winter when severe pollution events often occur. Nationally, the contributions of different source sectors to annual total PM 2.5 from high to low are industries, residential sources, agriculture, power plants, transportation, windblown dust, open burning and sea salt. Provincially, residential sources and industries are the major anthropogenic sources of primary PM 2.5 , while industries, agriculture, power plants and transportation are important for SNA in most provinces. For total PM 2.5 , residential and industrial emissions are the top two sources, with a combined contribution of 40-50% in most provinces. The contributions of power plants and agriculture to total PM 2.5 are about 10%, respectively. Secondary organic aerosol accounts for about 10% of annual PM 2.5 in most provinces, with higher contributions in southern provinces such as Yunnan (26%), Hainan (25%) and Taiwan (21%). Windblown dust is an important source in western provinces such as Xizang (55% of total PM 2.5 ), Qinghai (74%), Xinjiang (59

Air Quality Standards for Particulate Matter (PM) at high altitude cities

International Nuclear Information System (INIS)

Bravo Alvarez, H.; Sosa Echeverria, R.; Sanchez Alvarez, P.; Krupa, S.

2013-01-01

The Air Quality Standards for Particulate Matter (PM) at high altitude urban areas in different countries, must consider the pressure and temperature due to the effect that these parameters have on the breath volume. This paper shows the importance to correct Air Quality Standards for PM considering pressure and temperature at different altitudes. Specific factors were suggested to convert the information concerning PM, from local to standard conditions, and adjust the Air Quality Standards for different high altitudes cities. The correction factors ranged from: 1.03 for Santiago de Chile to 1.47 for El Alto Bolivia. Other cities in this study include: Mexico City, México; La Paz, Bolivia; Bogota, Cali and Medellin, Colombia; Quito, Ecuador and Cuzco, Peru. If these corrections are not considered, the atmospheric concentrations will be underestimated. - Highlights: ► AQS for particulate matter concentrations adjusted by pressure and temperature. ► Particulate matter concentrations can be underestimated in high altitude Cities. ► Particulate matter concentrations must be compared under the same conditions. - In order to compare high altitude atmospheric PM concentrations with AQS, one must consider T and P of the sampling site.

Source Apportionment and Elemental Composition of PM2.5 and PM10 in Jeddah City, Saudi Arabia.

Science.gov (United States)

Khodeir, Mamdouh; Shamy, Magdy; Alghamdi, Mansour; Zhong, Mianhua; Sun, Hong; Costa, Max; Chen, Lung-Chi; Maciejczyk, Polina

2012-07-01

This paper presents the first comprehensive investigation of PM2.5 and PM10 composition and sources in Saudi Arabia. We conducted a multi-week multiple sites sampling campaign in Jeddah between June and September, 2011, and analyzed samples by XRF. The overall mean mass concentration was 28.4 ± 25.4 μg/m 3 for PM2.5 and 87.3 ± 47.3 μg/m 3 for PM10, with significant temporal and spatial variability. The average ratio of PM2.5/PM10 was 0.33. Chemical composition data were modeled using factor analysis with varimax orthogonal rotation to determine five and four particle source categories contributing significant amount of for PM2.5 and PM10 mass, respectively. In both PM2.5 and PM10 sources were (1) heavy oil combustion characterized by high Ni and V; (2) resuspended soil characterized by high concentrations of Ca, Fe, Al, and Si; and (3) marine aerosol. The two other sources in PM2.5 were (4) Cu/Zn source; (5) traffic source identified by presence of Pb, Br, and Se; while in PM10 it was a mixed industrial source. To estimate the mass contributions of each individual source category, the CAPs mass concentration was regressed against the factor scores. Cumulatively, resuspended soil and oil combustion contributed 77 and 82% mass of PM2.5 and PM10, respectively.

Characterization and source apportionment of health risks from ambient PM10 in Hong Kong over 2000-2011

Science.gov (United States)

Li, Zhiyuan; Yuan, Zibing; Li, Ying; Lau, Alexis K. H.; Louie, Peter K. K.

2015-12-01

Atmospheric particulate matter (PM) pollution is a major public health concern in Hong Kong. In this study, the spatiotemporal variations of health risks from ambient PM10 from seven air quality monitoring stations between 2000 and 2011 were analyzed. Positive matrix factorization (PMF) was adopted to identify major source categories of ambient PM10 and quantify their contributions. Afterwards, a point-estimated risk model was used to identify the inhalation cancer and non-cancer risks of PM10 sources. The long-term trends of the health risks from classified local and non-local sources were explored. Furthermore, the reason for the increase of health risks during high PM10 days was discussed. Results show that vehicle exhaust source was the dominant inhalation cancer risk (ICR) contributor (72%), whereas trace metals and vehicle exhaust sources contributed approximately 27% and 21% of PM10 inhalation non-cancer risk (INCR), respectively. The identified local sources accounted for approximately 80% of the ICR in Hong Kong, while contribution percentages of the non-local and local sources for INCR are comparable. The clear increase of ICR at high PM days was mainly attributed to the increase of contributions from coal combustion/biomass burning and secondary sulfate, while the increase of INCR at high PM days was attributed to the increase of contributions from the sources coal combustion/biomass burning, secondary nitrate, and trace metals. This study highlights the importance of health risk-based source apportionment in air quality management with protecting human health as the ultimate target.

Characterization of Fine Particulate Matter (PM) and Secondary PM Precursor Gases in Mexico City

Energy Technology Data Exchange (ETDEWEB)

Dr. Charles E. Kolb

2008-03-31

This project was one of three collaborating grants designed to understand the atmospheric chemistry and aerosol particle microphysics impacting air quality in the Mexico City Metropolitan Area (MCMA) and its urban plume. The overall effort, titled MCMA- 2006, focused on: 1) the primary emissions of fine particles and precursor gases leading to photochemical production of atmospheric oxidants and secondary aerosol particles and 2) the measurement and analysis of secondary oxidants and secondary fine particular matter (PM) production, with particular emphasis on secondary organic aerosol (SOA). MCAM-2006 pursued it goals through three main activities: 1) performance and publication of detailed analyses of extensive MCMA trace gas and fine PM measurements made by the collaborating groups and others during earlier MCMA field campaigns in 2002 and 2003; 2) deployment and utilization of extensive real-time trace gas and fine PM instrumentation at urban and downwind MCMA sites in support of the MAX-Mex/MILAGRO field measurements in March, 2006; and, 3) analyses of the 2006 MCMA data sets leading to further publications that are based on new data as well as insights from analysis and publication of the 2002/2003 field data. Thirteen archival publications were coauthored with other MCMA-2003 participants. Documented findings included a significantly improved speciated emissions inventory from on-road vehicles, a greatly enhanced understanding of the sources and atmospheric loadings of volatile organic compounds, a unique analysis of the high fraction of ambient formaldehyde from primary emission sources, a much more extensive knowledge of the composition, size distributions and atmospheric mass loadings of both primary and secondary fine PM, including the fact that the rate of MCMA SOA production greatly exceeded that predicted by current atmospheric models, and evaluations of significant errors that can arise from standard air quality monitors for ozone and nitrogen

Particulate Matter Sources and Composition near a Shrinking Saline Lake (Salton Sea)

Science.gov (United States)

Frie, A. L.; Dingle, J. H.; Garrison, A.; Ying, S.; Bahreini, R.

2017-12-01

Dried lake beds (playas) are large dust sources in arid regions, and with increased global water demand many large lakes are shrinking. The Salton Sea is an example of one such lake in the early stages of desiccation, with about 15,000 acres of exposed playa. To quantify the impacts of the shrinking lake on airborne particulate matter(PM) composition, PM samples were collected in August of 2015 and February of 2016 near the Salton Sea, CA. These samples were analyzed for total elemental concentration of 15 elements. For these elements, enrichment factors relative to aluminum were calculated and PMF modeling was applied to deconvolve source factors. From these data, desert-like and playa-like sources were estimated to accounted for 45% and 9% of PM10 mass during these sampling periods. PMF results also revealed that playa sources account for 70% of PM10 Na, evidencing playa-driven PM compositional changes. Additionally, PM Se displayed strong seasonal variation, which is thought to be driven by Se volatilization within Salton Sea sediments, playas, or waters.

Source influence on emission pathways and ambient PM2.5 pollution over India (2015-2050)

Science.gov (United States)

Venkataraman, Chandra; Brauer, Michael; Tibrewal, Kushal; Sadavarte, Pankaj; Ma, Qiao; Cohen, Aaron; Chaliyakunnel, Sreelekha; Frostad, Joseph; Klimont, Zbigniew; Martin, Randall V.; Millet, Dylan B.; Philip, Sajeev; Walker, Katherine; Wang, Shuxiao

2018-06-01

India is currently experiencing degraded air quality, and future economic development will lead to challenges for air quality management. Scenarios of sectoral emissions of fine particulate matter and its precursors were developed and evaluated for 2015-2050, under specific pathways of diffusion of cleaner and more energy-efficient technologies. The impacts of individual source sectors on PM2.5 concentrations were assessed through systematic simulations of spatially and temporally resolved particulate matter concentrations, using the GEOS-Chem model, followed by population-weighted aggregation to national and state levels. We find that PM2.5 pollution is a pan-India problem, with a regional character, and is not limited to urban areas or megacities. Under present-day emissions, levels in most states exceeded the national PM2.5 annual standard (40 µg m-3). Sources related to human activities were responsible for the largest proportion of the present-day population exposure to PM2.5 in India. About 60 % of India's mean population-weighted PM2.5 concentrations come from anthropogenic source sectors, while the remainder are from other sources, windblown dust and extra-regional sources. Leading contributors are residential biomass combustion, power plant and industrial coal combustion and anthropogenic dust (including coal fly ash, fugitive road dust and waste burning). Transportation, brick production and distributed diesel were other contributors to PM2.5. Future evolution of emissions under regulations set at current levels and promulgated levels caused further deterioration of air quality in 2030 and 2050. Under an ambitious prospective policy scenario, promoting very large shifts away from traditional biomass technologies and coal-based electricity generation, significant reductions in PM2.5 levels are achievable in 2030 and 2050. Effective mitigation of future air pollution in India requires adoption of aggressive prospective regulation, currently not formulated

The Use of Principal Component Analysis for Source Identification of PM2.5 from Selected Urban and Regional Background Sites in Poland

Science.gov (United States)

Błaszczak, Barbara

2018-01-01

The paper reports the results of the measurements of water-soluble ions and carbonaceous matter content in the fine particulate matter (PM2.5), as well as the contributions of major sources in PM2.5. Daily PM2.5 samples were collected during heating and non-heating season of the year 2013 in three different locations in Poland: Szczecin (urban background), Trzebinia (urban background) and Złoty Potok (regional background). The concentrations of PM2.5, and its related components, exhibited clear spatiotemporal variability with higher levels during the heating period. The share of the total carbon (TC) in PM2.5 exceeded 40% and was primarily determined by fluctuations in the share of OC. Sulfates (SO42-), nitrates (NO3-) and ammonium (NH4+) dominated in the ionic composition of PM2.5 and accounted together 34% (Szczecin), 30% (Trzebinia) and 18% (Złoty Potok) of PM2.5 mass. Source apportionment analysis, performed by PCA-MLRA model (Principal Component Analysis - Multilinear Regression Analysis), revealed that secondary aerosol, whose presence is related to oxidation of gaseous precursors emitted from fuel combustion and biomass burning, had the largest contribution in observed PM2.5 concentrations. In addition, the contribution of traffic sources together with road dust resuspension, was observed. The share of natural sources (sea spray, crustal dust) was generally lower.

The Use of Principal Component Analysis for Source Identification of PM2.5 from Selected Urban and Regional Background Sites in Poland

Directory of Open Access Journals (Sweden)

Błaszczak Barbara

2018-01-01

Full Text Available The paper reports the results of the measurements of water-soluble ions and carbonaceous matter content in the fine particulate matter (PM2.5, as well as the contributions of major sources in PM2.5. Daily PM2.5 samples were collected during heating and non-heating season of the year 2013 in three different locations in Poland: Szczecin (urban background, Trzebinia (urban background and Złoty Potok (regional background. The concentrations of PM2.5, and its related components, exhibited clear spatiotemporal variability with higher levels during the heating period. The share of the total carbon (TC in PM2.5 exceeded 40% and was primarily determined by fluctuations in the share of OC. Sulfates (SO42-, nitrates (NO3- and ammonium (NH4+ dominated in the ionic composition of PM2.5 and accounted together ~34% (Szczecin, ~30% (Trzebinia and ~18% (Złoty Potok of PM2.5 mass. Source apportionment analysis, performed by PCA-MLRA model (Principal Component Analysis – Multilinear Regression Analysis, revealed that secondary aerosol, whose presence is related to oxidation of gaseous precursors emitted from fuel combustion and biomass burning, had the largest contribution in observed PM2.5 concentrations. In addition, the contribution of traffic sources together with road dust resuspension, was observed. The share of natural sources (sea spray, crustal dust was generally lower.

Seasonal variability of PM2.5 composition and sources in the Klang Valley urban-industrial environment

Science.gov (United States)

Amil, Norhaniza; Talib Latif, Mohd; Firoz Khan, Md; Mohamad, Maznorizan

2016-04-01

This study investigates the fine particulate matter (PM2.5) variability in the Klang Valley urban-industrial environment. In total, 94 daily PM2.5 samples were collected during a 1-year campaign from August 2011 to July 2012. This is the first paper on PM2.5 mass, chemical composition and sources in the tropical environment of Southeast Asia, covering all four seasons (distinguished by the wind flow patterns) including haze events. The samples were analysed for various inorganic components and black carbon (BC). The chemical compositions were statistically analysed and the temporal aerosol pattern (seasonal) was characterised using descriptive analysis, correlation matrices, enrichment factor (EF), stoichiometric analysis and chemical mass closure (CMC). For source apportionment purposes, a combination of positive matrix factorisation (PMF) and multi-linear regression (MLR) was employed. Further, meteorological-gaseous parameters were incorporated into each analysis for improved assessment. In addition, secondary data of total suspended particulate (TSP) and coarse particulate matter (PM10) sampled at the same location and time with this study (collected by Malaysian Meteorological Department) were used for PM ratio assessment. The results showed that PM2.5 mass averaged at 28 ± 18 µg m-3, 2.8-fold higher than the World Health Organisation (WHO) annual guideline. On a daily basis, the PM2.5 mass ranged between 6 and 118 µg m-3 with the daily WHO guideline exceeded 43 % of the time. The north-east (NE) monsoon was the only season with less than 50 % sample exceedance of the daily WHO guideline. On an annual scale, PM2.5 mass correlated positively with temperature (T) and wind speed (WS) but negatively with relative humidity (RH). With the exception of NOx, the gases analysed (CO, NO2, NO and SO2) were found to significantly influence the PM2.5 mass. Seasonal variability unexpectedly showed that rainfall, WS and wind direction (WD) did not significantly correlate

Chemical characterization of outdoor and subway fine (PM(2.5-1.0)) and coarse (PM(10-2.5)) particulate matter in Seoul (Korea) by computer-controlled scanning electron microscopy (CCSEM).

Science.gov (United States)

Byeon, Sang-Hoon; Willis, Robert; Peters, Thomas M

2015-02-13

Outdoor and indoor (subway) samples were collected by passive sampling in urban Seoul (Korea) and analyzed with computer-controlled scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (CCSEM-EDX). Soil/road dust particles accounted for 42%-60% (by weight) of fine particulate matter larger than 1 µm (PM(2.5-1.0)) in outdoor samples and 18% of PM2.5-1.0 in subway samples. Iron-containing particles accounted for only 3%-6% in outdoor samples but 69% in subway samples. Qualitatively similar results were found for coarse particulate matter (PM(10-2.5)) with soil/road dust particles dominating outdoor samples (66%-83%) and iron-containing particles contributing most to subway PM(10-2.5) (44%). As expected, soil/road dust particles comprised a greater mass fraction of PM(10-2.5) than PM(2.5-1.0). Also as expected, the mass fraction of iron-containing particles was substantially less in PM(10-2.5) than in PM(2.5-1.0). Results of this study are consistent with known emission sources in the area and with previous studies, which showed high concentrations of iron-containing particles in the subway compared to outdoor sites. Thus, passive sampling with CCSEM-EDX offers an inexpensive means to assess PM(2.5-1.0) and PM(10-2.5) simultaneously and by composition at multiple locations.

Fine Particle Matter (PM2.5) Design Value

Data.gov (United States)

U.S. Environmental Protection Agency — Fine particulate matter or PM2.5 (total mass of particles below 2.5 micron is diameter) is known to cause adverse health effects in humans.See the following websites...

Review on recent progress in observations, source identifications and countermeasures of PM2.5.

Science.gov (United States)

Liang, Chun-Sheng; Duan, Feng-Kui; He, Ke-Bin; Ma, Yong-Liang

2016-01-01

Recently, PM2.5 (atmospheric fine particulate matter with aerodynamic diameter ≤ 2.5 μm) have received so much attention that the observations, source appointment and countermeasures of it have been widely studied due to its harmful impacts on visibility, mood (mental health), physical health, traffic safety, construction, economy and nature, as well as its complex interaction with climate. A review on the PM2.5 related research is necessary. We start with summary of chemical composition and characteristics of PM2.5 that contains both macro and micro observation results and analysis, wherein the temporal variability of concentrations of PM2.5 and major components in many recent reports is embraced. This is closely followed by an overview of source appointment, including the composition and sources of PM2.5 in different countries in the six inhabitable continents based on the best available results. Besides summarizing PM2.5 pollution countermeasures by policy, planning, technology and ideology, the World Air Day is proposed to be established to inspire and promote the crucial social action in energy-saving and emission-reduction. Some updated knowledge of the important topics (such as formation and evolution mechanisms of hazes, secondary aerosols, aerosol mass spectrometer, organic tracers, radiocarbon, emissions, solutions for air pollution problems, etc.) is also included in the present review by logically synthesizing the studies. In addition, the key research challenges and future directions are put forward. Despite our efforts, our understanding of the recent reported observations, source identifications and countermeasures of PM2.5 is limited, and subsequent efforts both of the authors and readers are needed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evolution of air pollution source contributions over one decade, derived by PM10 and PM2.5 source apportionment in two metropolitan urban areas in Greece

Science.gov (United States)

Diapouli, E.; Manousakas, M.; Vratolis, S.; Vasilatou, V.; Maggos, Th; Saraga, D.; Grigoratos, Th; Argyropoulos, G.; Voutsa, D.; Samara, C.; Eleftheriadis, K.

2017-09-01

Metropolitan Urban areas in Greece have been known to suffer from poor air quality, due to variety of emission sources, topography and climatic conditions favouring the accumulation of pollution. While a number of control measures have been implemented since the 1990s, resulting in reductions of atmospheric pollution and changes in emission source contributions, the financial crisis which started in 2009 has significantly altered this picture. The present study is the first effort to assess the contribution of emission sources to PM10 and PM2.5 concentration levels and their long-term variability (over 5-10 years), in the two largest metropolitan urban areas in Greece (Athens and Thessaloniki). Intensive measurement campaigns were conducted during 2011-2012 at suburban, urban background and urban traffic sites in these two cities. In addition, available datasets from previous measurements in Athens and Thessaloniki were used in order to assess the long-term variability of concentrations and sources. Chemical composition analysis of the 2011-2012 samples showed that carbonaceous matter was the most abundant component for both PM size fractions. Significant increase of carbonaceous particle concentrations and of OC/EC ratio during the cold period, especially in the residential urban background sites, pointed towards domestic heating and more particularly wood (biomass) burning as a significant source. PMF analysis further supported this finding. Biomass burning was the largest contributing source at the two urban background sites (with mean contributions for the two size fractions in the range of 24-46%). Secondary aerosol formation (sulphate, nitrate & organics) was also a major contributing source for both size fractions at the suburban and urban background sites. At the urban traffic site, vehicular traffic (exhaust and non-exhaust emissions) was the source with the highest contributions, accounting for 44% of PM10 and 37% of PM2.5, respectively. The long

PIXE characterization of PM10 and PM2.5 particulate matter collected during the winter season in Shanghai city

International Nuclear Information System (INIS)

Zhang Yuanxun; Wang Yingsong; Li Delu; Li Aiguo; Li Yan; Zhang Guilin

2006-01-01

The samples of PM2.5 and PM10 inhalable particulate matter had been collected during the period of December 2002-January 2003 at nineteen representative sites of Shanghai urban and suburb area in order to investigate the chemical characterization of aerosol particle in winter. The samples were analyzed to determine the average concentrations for up to twenty elements by means of particle induced X-ray emission (PIXE). It was found that the average elemental concentrations in the urban center are higher than those in the suburb, except for Ti and P. The particulate mass data demonstrate that the ratio range of PM2.5/PM10 is from 0.32 to 0.85 and its average ratio is 0.6. The result of the enrichment factor shows that the inhalable particles may be divided into two categories, i.e., soil elements from the earth crust and anthropogenic pollution elements. It is noticed that toxic or harmful elements such as S, As, Pb, Ni, Mn and Se are enriched mainly in fine particles with diameter less than 2.5 μm. The fingerprints of major pollution sources such as coal (or oil) burning, vehicle exhaust emission and industry are also presented and discussed. (author)

Outdoor particulate matter (PM and associated cardiovascular diseases in the Middle East

Directory of Open Access Journals (Sweden)

Zeina Nasser

2015-08-01

Full Text Available Air pollution is a widespread environmental concern. Considerable epidemiological evidence indicates air pollution, particularly particulate matter (PM, as a major risk factor for cardiovascular diseases (CVD in the developed countries. The main objective of our review is to assess the levels and sources of PM across the Middle East area and to search evidence for the relationship between PM exposure and CVD. An extensive review of the published literature pertaining to the subject (2000–2013 was conducted using PubMed, Medline and Google Scholar databases. We reveal that low utilization of public transport, ageing vehicle fleet and the increasing number of personal cars in the developing countries all contribute to the traffic congestion and aggravate the pollution problem. The annual average values of PM pollutants in the Middle East region are much higher than the World Health Organization 2006 guidelines (PM2.5 = 10 μg/m3, PM10 = 20 μg/m3. We uncover evidence on the association between PM and CVD in 4 Middle East countries: Iran, Kingdom of Saudi Arabia, Qatar and the United Arab Emirates. The findings are in light of the international figures. Ambient PM pollution is considered a potential risk factor for platelet activation and atherosclerosis and has been found to be linked with an increased risk for mortality and hospital admissions due to CVD. This review highlights the importance of developing a strategy to improve air quality and reduce outdoor air pollution in the developing countries, particularly in the Middle East. Future studies should weigh the potential impact of PM on the overall burden of cardiac diseases.

Source apportionment of speciated PM2.5 and non-parametric regressions of PM2.5 and PM(coarse) mass concentrations from Denver and Greeley, Colorado, and construction and evaluation of dichotomous filter samplers

Science.gov (United States)

Piedrahita, Ricardo A.

The Denver Aerosol Sources and Health study (DASH) was a long-term study of the relationship between the variability in fine particulate mass and chemical constituents (PM2.5, particulate matter less than 2.5mum) and adverse health effects such as cardio-respiratory illnesses and mortality. Daily filter samples were chemically analyzed for multiple species. We present findings based on 2.8 years of DASH data, from 2003 to 2005. Multilinear Engine 2 (ME-2), a receptor-based source apportionment model was applied to the data to estimate source contributions to PM2.5 mass concentrations. This study relied on two different ME-2 models: (1) a 2-way model that closely reflects PMF-2; and (2) an enhanced model with meteorological data that used additional temporal and meteorological factors. The Coarse Rural Urban Sources and Health study (CRUSH) is a long-term study of the relationship between the variability in coarse particulate mass (PMcoarse, particulate matter between 2.5 and 10mum) and adverse health effects such as cardio-respiratory illnesses, pre-term births, and mortality. Hourly mass concentrations of PMcoarse and fine particulate matter (PM2.5) are measured using tapered element oscillating microbalances (TEOMs) with Filter Dynamics Measurement Systems (FDMS), at two rural and two urban sites. We present findings based on nine months of mass concentration data, including temporal trends, and non-parametric regressions (NPR) results, which were used to characterize the wind speed and wind direction relationships that might point to sources. As part of CRUSH, 1-year coarse and fine mode particulate matter filter sampling network, will allow us to characterize the chemical composition of the particulate matter collected and perform spatial comparisons. This work describes the construction and validation testing of four dichotomous filter samplers for this purpose. The use of dichotomous splitters with an approximate 2.5mum cut point, coupled with a 10mum cut

Modelling street level PM10 concentrations across Europe: source apportionment and possible futures

Directory of Open Access Journals (Sweden)

G. Kiesewetter

2015-02-01

Full Text Available Despite increasing emission controls, particulate matter (PM has remained a critical issue for European air quality in recent years. The various sources of PM, both from primary particulate emissions as well as secondary formation from precursor gases, make this a complex problem to tackle. In order to allow for credible predictions of future concentrations under policy assumptions, a modelling approach is needed that considers all chemical processes and spatial dimensions involved, from long-range transport of pollution to local emissions in street canyons. Here we describe a modelling scheme which has been implemented in the GAINS integrated assessment model to assess compliance with PM10 (PM with aerodynamic diameter 10 across Europe. Furthermore, we analyse the predicted evolution of PM10 concentrations in the European Union until 2030 under different policy scenarios. Significant improvements in ambient PM10 concentrations are expected assuming successful implementation of already agreed legislation; however, these will not be large enough to ensure attainment of PM10 limit values in hot spot locations such as Southern Poland and major European cities. Remaining issues are largely eliminated in a scenario applying the best available emission control technologies to the maximal technically feasible extent.

Wintertime indoor air levels of PM10, PM2.5 and PM1 at public places and their contributions to TSP.

Science.gov (United States)

Liu, Yangsheng; Chen, Rui; Shen, Xingxing; Mao, Xiaoling

2004-04-01

From 26 October 2002 to 8 March 2003, particulate matter (PM) concentrations (total suspended particles [TSP], PM10, PM2.5 and PM1) were measured at 49 public places representing different environments in the urban area of Beijing. The objectives of this study were (1) to characterize the indoor PM concentrations in public places, (2) to evaluate the potential indoor sources and (3) to investigate the contribution of PM10 to TSP and the contributions of PM2.5 and PM1 to PM10. Additionally, The indoor and outdoor particle concentrations in the same type of indoor environment were employed to investigate the I/O level, and comparison was made between I/O levels in different types of indoor environment. Construction activities and traffic condition were the major outdoor sources to influence the indoor particle levels. The contribution of PM10 to TSP was even up to 68.8%, while the contributions of PM2.5 and PM1 to PM10 were not as much as that of PM10 to TSP.

The impact of particulate matter (PM and nitric oxides (NOx on human health and an analysis of selected sources accounting for their emission in Poland

Directory of Open Access Journals (Sweden)

Jakub Krzeszowiak

2016-10-01

Full Text Available Introduction and objective: This paper is concerned with the harmful impact of nitric oxides (NOx and particulate matter (PM on humans. The objective was to determine which source of emission is the most urgent in terms of its reduction.Abbreviated description of the state of knowledge: In published epidemiological studies multiple notifications indicating the harmful impact of particulate matter on human health can be found. The harmful impact is underscored by the increase in the number of hospitalisations owing to diseases of respiratory and cardio-vascular systems, as well as by the rise in general fatality rate. The analysis of the PM impact on the human body is prompted by the fact that its detrimental effects are not clearly defined. Additionally, nitric oxides contribute to the increased number of exacerbations of respiratory disease and are a factor increasing susceptibility to development of local inflammation. Conclusions: The following study is meant to show that the air pollution which derives from vehicles (NOx and PM has a significant impact on human health. This applies particularly to residents of cities and big towns. This issue has gained special importance in Poland. According to the data from the Central Statistical Office, the increasing number of vehicles in use and their age lead to increased emission of the pollutants considered.

Particulate matter (PM 10 ) in Istanbul: Origin, source areas and potential impact on surrounding regions

Science.gov (United States)

Koçak, M.; Theodosi, C.; Zarmpas, P.; Im, U.; Bougiatioti, A.; Yenigun, O.; Mihalopoulos, N.

2011-12-01

Water-soluble ions (Cl -, NO3-, SO42-, CO4-, Na +, NH4+, K +, Mg 2+,Ca 2+), water soluble organic carbon (WSOC), organic and elemental carbon (OC, EC) and trace metals (Al, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Cd and Pb) were measured in aerosol PM 10 samples above the megacity of Istanbul between November 2007 and June 2009. Source apportionment analysis using Positive Matrix Factorization (PMF) indicates that approximately 80% of the PM 10 is anthropogenic in origin (secondary, refuse incineration, fuel oil and solid fuel combustion and traffic). Crustal and sea salt account for 10.2 and 7.5% of the observed mass, respectively. In general, anthropogenic (except secondary) aerosol shows higher concentrations and contributions in winter. Mean concentration and contribution of crustal source is found to be more important during the transitional period due to mineral dust transport from North Africa. During the sampling period, 42 events exceeding the limit value of 50 μg m -3 are identified. A significant percentage (91%; n = 38) of these exceedances is attributed to anthropogenic sources. Potential Source Contribution Function analysis highlights that Istanbul is affected from distant sources from Balkans and Western Europe during winter and from Eastern Europe during summer. On the other hand, Istanbul sources influence western Black Sea and Eastern Europe during winter and Aegean and Levantine Sea during summer.

Seasonal variability of PM2.5 composition and sources in the Klang Valley urban-industrial environment

Directory of Open Access Journals (Sweden)

N. Amil

2016-04-01

Full Text Available This study investigates the fine particulate matter (PM2.5 variability in the Klang Valley urban-industrial environment. In total, 94 daily PM2.5 samples were collected during a 1-year campaign from August 2011 to July 2012. This is the first paper on PM2.5 mass, chemical composition and sources in the tropical environment of Southeast Asia, covering all four seasons (distinguished by the wind flow patterns including haze events. The samples were analysed for various inorganic components and black carbon (BC. The chemical compositions were statistically analysed and the temporal aerosol pattern (seasonal was characterised using descriptive analysis, correlation matrices, enrichment factor (EF, stoichiometric analysis and chemical mass closure (CMC. For source apportionment purposes, a combination of positive matrix factorisation (PMF and multi-linear regression (MLR was employed. Further, meteorological–gaseous parameters were incorporated into each analysis for improved assessment. In addition, secondary data of total suspended particulate (TSP and coarse particulate matter (PM10 sampled at the same location and time with this study (collected by Malaysian Meteorological Department were used for PM ratio assessment. The results showed that PM2.5 mass averaged at 28 ± 18 µg m−3, 2.8-fold higher than the World Health Organisation (WHO annual guideline. On a daily basis, the PM2.5 mass ranged between 6 and 118 µg m−3 with the daily WHO guideline exceeded 43 % of the time. The north-east (NE monsoon was the only season with less than 50 % sample exceedance of the daily WHO guideline. On an annual scale, PM2.5 mass correlated positively with temperature (T and wind speed (WS but negatively with relative humidity (RH. With the exception of NOx, the gases analysed (CO, NO2, NO and SO2 were found to significantly influence the PM2.5 mass. Seasonal variability unexpectedly showed that rainfall, WS and wind direction (WD did not

Toxic potential of organic constituents of submicron particulate matter (PM1) in an urban road site (Barcelona).

Science.gov (United States)

Mesquita, Sofia R; van Drooge, Barend L; Dall'Osto, Manuel; Grimalt, Joan O; Barata, Carlos; Vieira, Natividade; Guimarães, Laura; Piña, Benjamin

2017-06-01

Atmospheric particulate matter (PM) is a recognized risk factor contributing to a number of diseases in human populations and wildlife globally. Organic matter is a major component of PM, but its contribution to overall toxicity of PM has not been thoroughly evaluated yet. In the present work, the biological activity of organic extracts from PM1 (particles with less than 1 μm of aerodynamic diameter) collected from an urban road site in the centre of Barcelona (NE Spain) was evaluated using a yeast-based assay (AhR-RYA) and different gene expression markers in zebrafish embryos. Dioxin-like activity of the extracts correlated to primary emissions from local traffic exhausts, reflecting weekday/weekend alternance. Expression levels of cyp1a and of gene markers for key cellular processes and development (ier2, fos) also correlated to vehicle emissions, whereas expression of gene markers related to antioxidant defence and endocrine effects (gstal, hao1, ttr) was strongly reduced in samples with strong contribution from regional air masses with aged secondary organic species or with strong influence of biomass burning emissions. Our data suggest that the toxic potential of PM1 organic chemical constituents strongly depends on the emission sources and on the process of ageing from primary to secondary organic aerosols.

Application of Positive Matrix Factorization in the Identification of the Sources of PM2.5 in Taipei City

Directory of Open Access Journals (Sweden)

Wen-Yuan Ho

2018-06-01

Full Text Available Fine particulate matter (PM2.5 has a small particle size, which allows it to directly enter the respiratory mucosa and reach the alveoli and even the blood. Many countries are already aware of the adverse effects of PM2.5, and determination of the sources of PM2.5 is a critical step in reducing its concentration to protect public health. This study monitored PM2.5 in the summer (during the southwest monsoon season of 2017. Three online monitoring systems were used to continuously collect hourly concentrations of key chemical components of PM2.5, including anions, cations, carbon, heavy metals, and precursor gases, for 24 h per day. The sum of the concentrations of each compound obtained from the online monitoring systems is similar to the actual PM2.5 concentration (98.75%. This result suggests that the on-line monitoring system of this study covers relatively complete chemical compounds. Positive matrix factorization (PMF was adopted to explore and examine the proportion of each source that contributed to the total PM2.5 concentration. According to the source contribution analysis, 55% of PM2.5 can be attributed to local pollutant sources, and the remaining 45% can be attributed to pollutants emitted outside Taipei City. During the high-PM2.5-concentration (episode period, the pollutant conversion rates were higher than usual due to the occurrence of vigorous photochemical reactions. Moreover, once pollutants are emitted by external stationary pollutant sources, they move with pollution air masses and undergo photochemical reactions, resulting in increases in the secondary pollutant concentrations of PM2.5. The vertical monitoring data indicate that there is a significant increase in PM2.5 concentration at high altitudes. High-altitude PM2.5 will descend to the ground and thereby affect the ground-level PM2.5 concentration.

Temporal variations and spatial distribution of ambient PM2.2 and PM1 concentrations in Dhaka, Bangladesh

International Nuclear Information System (INIS)

Begum, Bilkis A.; Biswas, Swapan K.; Hopke, Philip K.

2006-01-01

Concentrations and characteristics of airborne particulate matter (PM 1 , PM 2.2 and BC) on air quality have been studied at two air quality-monitoring stations in Dhaka, the capital of Bangladesh. One site is at the Farm Gate area, a hot spot with very high pollutant concentrations because of its proximity to major roadways. The other site is at a semi-residential area located at the Atomic Energy Centre, Dhaka Campus, (AECD) with relatively less traffic. The samples were collected using a 'Gent' stacked filter unit in two fractions of 0-2.2 μm and 2.2-10 μm sizes. Samples of fine (PM 2.2 ) and coarse (PM 2.2-1 ) airborne particulate matter fractions collected from 2000 to 2003 were studied. It has been observed that fine particulate matter has a decreasing trend, from prior year measurements, because of Government policy interventions like phase-wise plans to take two-stroke three-wheelers off the roads in Dhaka and finally banned from January 1, 2003. Other policy interventions were banning of old buses and trucks to ply on Dhaka city promotion of the using compressed natural gas (CNG), introducing air pollution control devices in vehicles, etc. It was found that both local (mostly from vehicular emissions) and possibly some regional emission sources are responsible for high PM 2.2 and BC concentrations in Dhaka. PM 2.2 , PM 2.2-1 and black carbon concentration levels depend on the season, wind direction and wind speed. Transport related emissions are the major source of BC and long-range transportation from fossil fuel related sources and biomass burning could be another substantial source of BC

Temporal variations and spatial distribution of ambient PM2.2 and PM10 concentrations in Dhaka, Bangladesh.

Science.gov (United States)

Begum, Bilkis A; Biswas, Swapan K; Hopke, Philip K

2006-04-01

Concentrations and characteristics of airborne particulate matter (PM(10), PM(2.2) and BC) on air quality have been studied at two air quality-monitoring stations in Dhaka, the capital of Bangladesh. One site is at the Farm Gate area, a hot spot with very high pollutant concentrations because of its proximity to major roadways. The other site is at a semi-residential area located at the Atomic Energy Centre, Dhaka Campus, (AECD) with relatively less traffic. The samples were collected using a 'Gent' stacked filter unit in two fractions of 0-2.2 mum and 2.2-10 mum sizes. Samples of fine (PM(2.2)) and coarse (PM(2.2-10)) airborne particulate matter fractions collected from 2000 to 2003 were studied. It has been observed that fine particulate matter has a decreasing trend, from prior year measurements, because of Government policy interventions like phase-wise plans to take two-stroke three-wheelers off the roads in Dhaka and finally banned from January 1, 2003. Other policy interventions were banning of old buses and trucks to ply on Dhaka city promotion of the using compressed natural gas (CNG), introducing air pollution control devices in vehicles, etc. It was found that both local (mostly from vehicular emissions) and possibly some regional emission sources are responsible for high PM(2.2) and BC concentrations in Dhaka. PM(2.2), PM(2.2-10) and black carbon concentration levels depend on the season, wind direction and wind speed. Transport related emissions are the major source of BC and long-range transportation from fossil fuel related sources and biomass burning could be another substantial source of BC.

Real-time particle monitor calibration factors and PM2.5 emission factors for multiple indoor sources.

Science.gov (United States)

Dacunto, Philip J; Cheng, Kai-Chung; Acevedo-Bolton, Viviana; Jiang, Ruo-Ting; Klepeis, Neil E; Repace, James L; Ott, Wayne R; Hildemann, Lynn M

2013-08-01

Indoor sources can greatly contribute to personal exposure to particulate matter less than 2.5 μm in diameter (PM2.5). To accurately assess PM2.5 mass emission factors and concentrations, real-time particle monitors must be calibrated for individual sources. Sixty-six experiments were conducted with a common, real-time laser photometer (TSI SidePak™ Model AM510 Personal Aerosol Monitor) and a filter-based PM2.5 gravimetric sampler to quantify the monitor calibration factors (CFs), and to estimate emission factors for common indoor sources including cigarettes, incense, cooking, candles, and fireplaces. Calibration factors for these indoor sources were all significantly less than the factory-set CF of 1.0, ranging from 0.32 (cigarette smoke) to 0.70 (hamburger). Stick incense had a CF of 0.35, while fireplace emissions ranged from 0.44-0.47. Cooking source CFs ranged from 0.41 (fried bacon) to 0.65-0.70 (fried pork chops, salmon, and hamburger). The CFs of combined sources (e.g., cooking and cigarette emissions mixed) were linear combinations of the CFs of the component sources. The highest PM2.5 emission factors per time period were from burned foods and fireplaces (15-16 mg min(-1)), and the lowest from cooking foods such as pizza and ground beef (0.1-0.2 mg min(-1)).

Outdoor particulate matter (PM) and associated cardiovascular diseases in the Middle East.

Science.gov (United States)

Nasser, Zeina; Salameh, Pascale; Nasser, Wissam; Abou Abbas, Linda; Elias, Elias; Leveque, Alain

2015-01-01

Air pollution is a widespread environmental concern. Considerable epidemiological evidence indicates air pollution, particularly particulate matter (PM), as a major risk factor for cardiovascular diseases (CVD) in the developed countries. The main objective of our review is to assess the levels and sources of PM across the Middle East area and to search evidence for the relationship between PM exposure and CVD. An extensive review of the published literature pertaining to the subject (2000-2013) was conducted using PubMed, Medline and Google Scholar databases. We reveal that low utilization of public transport, ageing vehicle fleet and the increasing number of personal cars in the developing countries all contribute to the traffic congestion and aggravate the pollution problem. The annual average values of PM pollutants in the Middle East region are much higher than the World Health Organization 2006 guidelines (PM2.5 = 10 μg/m(3), PM10 = 20 μg/m(3)). We uncover evidence on the association between PM and CVD in 4 Middle East countries: Iran, Kingdom of Saudi Arabia, Qatar and the United Arab Emirates. The findings are in light of the international figures. Ambient PM pollution is considered a potential risk factor for platelet activation and atherosclerosis and has been found to be linked with an increased risk for mortality and hospital admissions due to CVD. This review highlights the importance of developing a strategy to improve air quality and reduce outdoor air pollution in the developing countries, particularly in the Middle East. Future studies should weigh the potential impact of PM on the overall burden of cardiac diseases. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Inter-comparison of receptor models for PM source apportionment: Case study in an industrial area

Science.gov (United States)

Viana, M.; Pandolfi, M.; Minguillón, M. C.; Querol, X.; Alastuey, A.; Monfort, E.; Celades, I.

2008-05-01

Receptor modelling techniques are used to identify and quantify the contributions from emission sources to the levels and major and trace components of ambient particulate matter (PM). A wide variety of receptor models are currently available, and consequently the comparability between models should be evaluated if source apportionment data are to be used as input in health effects studies or mitigation plans. Three of the most widespread receptor models (principal component analysis, PCA; positive matrix factorization, PMF; chemical mass balance, CMB) were applied to a single PM10 data set (n=328 samples, 2002-2005) obtained from an industrial area in NE Spain, dedicated to ceramic production. Sensitivity and temporal trend analyses (using the Mann-Kendall test) were applied. Results evidenced the good overall performance of the three models (r2>0.83 and α>0.91×between modelled and measured PM10 mass), with a good agreement regarding source identification and high correlations between input (CMB) and output (PCA, PMF) source profiles. Larger differences were obtained regarding the quantification of source contributions (up to a factor of 4 in some cases). The combined application of different types of receptor models would solve the limitations of each of the models, by constructing a more robust solution based on their strengths. The authors suggest the combined use of factor analysis techniques (PCA, PMF) to identify and interpret emission sources, and to obtain a first quantification of their contributions to the PM mass, and the subsequent application of CMB. Further research is needed to ensure that source apportionment methods are robust enough for application to PM health effects assessments.

Monitoring and source apportionment of trace elements in PM2.5: Implications for local air quality management.

Science.gov (United States)

Li, Yueyan; Chang, Miao; Ding, Shanshan; Wang, Shiwen; Ni, Dun; Hu, Hongtao

2017-07-01

Fine particulate matter (PM 2.5 ) samples were collected simultaneously every hour in Beijing between April 2014 and April 2015 at five sites. Thirteen trace elements (TEs) in PM 2.5 were analyzed by online X-ray fluorescence (XRF). The annual average PM 2.5 concentrations ranged from 76.8 to 102.7 μg m -3 . TEs accounted for 5.9%-8.7% of the total PM 2.5 mass with Cl, S, K, and Si as the most dominant elements. Spearman correlation coefficients of PM 2.5 or TE concentrations between the background site and other sites showed that PM 2.5 and some element loadings were affected by regional and local sources, whereas Cr, Si, and Ni were attributed to substantial local emissions. Temporal variations of TEs in PM 2.5 were significant and provided information on source profiles. The PM 2.5 concentrations were highest in autumn and lowest in summer. Mn and Cr showed similar variation. Fe, Ca, Si, and Ti tended to show higher concentrations in spring, whereas concentrations of S peaked in summer. Concentrations of Cl, K, Pb, Zn, Cu, and Ni peaked in winter. PM 2.5 and TE median concentrations were higher on Saturdays than on weekdays. The diurnal pattern of PM 2.5 and TE median concentrations yielded similar bimodal patterns. Five dominant sources of PM 2.5 mass were identified via positive matrix factorization (PMF). These sources included the regional and local secondary aerosols, traffic, coal burning, soil dust, and metal processing. Air quality management strategies, including regional environmental coordination and collaboration, reduction in secondary aerosol precursors, restrictive vehicle emission standards, promotion of public transport, and adoption of clean energy, should be strictly implemented. High time-resolution measurements of TEs provided detailed source profiles, which can greatly improve precision in interpreting source apportionment calculations; the PMF analysis of online XRF data is a powerful tool for local air quality management. Copyright �

PIXE Analysis and source identification of airborne particulate matter collected in Downtown Havana City

International Nuclear Information System (INIS)

Perez, G.; Pinnera, I; Ramos, M; Guibert, R; Molina, E.; Martinez, M.; Fernandez, A.; Aldape, F.; Flores, M.

2009-01-01

A set of samples containing airborne particulate matter (in two particle size fraction PM10 and PM2,5) collected during five months from November 2006 to April 2007 in a urban area of Havana City were analyzed by Particle-Induced X-ray Emission (PIXE) technique and the concentrations of 14 elements (S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br and Pb) were determined consistently in both particle size fractions with minimum detection limits in the range of ng/m3. A Gent air sampler was used for the aerosol collection in PM10 and PM2,5 particles simultaneously and the PIXE elemental analysis were performed using a proton beam of 2.5 MeV from the 2 MV Van de Graff Tandetron Accelerator at the ININ PIXE Laboratory in Mexico. The analytical database provided by PIXE was statistically analyzed in order to determine the promising local pollution sources. The statistical techniques of Multivariate Factor Analysis in combination with the Principal Component Analysis methods were applied to this data and allowed identifying five main pollution sources of airborne particulate matter (PM10 and PM2,5) collected in this area. The main (local) identified sources were: soil dust, sea spray, industry, fossil fuel combustion from motor vehicles and burnings or incinerations of diverse materials. A general discussion about these results is presented in this work. (Author)

Source influence on emission pathways and ambient PM2.5 pollution over India (2015–2050

Directory of Open Access Journals (Sweden)

C. Venkataraman

2018-06-01

Full Text Available India is currently experiencing degraded air quality, and future economic development will lead to challenges for air quality management. Scenarios of sectoral emissions of fine particulate matter and its precursors were developed and evaluated for 2015–2050, under specific pathways of diffusion of cleaner and more energy-efficient technologies. The impacts of individual source sectors on PM2.5 concentrations were assessed through systematic simulations of spatially and temporally resolved particulate matter concentrations, using the GEOS-Chem model, followed by population-weighted aggregation to national and state levels. We find that PM2.5 pollution is a pan-India problem, with a regional character, and is not limited to urban areas or megacities. Under present-day emissions, levels in most states exceeded the national PM2.5 annual standard (40 µg m−3. Sources related to human activities were responsible for the largest proportion of the present-day population exposure to PM2.5 in India. About 60 % of India's mean population-weighted PM2.5 concentrations come from anthropogenic source sectors, while the remainder are from other sources, windblown dust and extra-regional sources. Leading contributors are residential biomass combustion, power plant and industrial coal combustion and anthropogenic dust (including coal fly ash, fugitive road dust and waste burning. Transportation, brick production and distributed diesel were other contributors to PM2.5. Future evolution of emissions under regulations set at current levels and promulgated levels caused further deterioration of air quality in 2030 and 2050. Under an ambitious prospective policy scenario, promoting very large shifts away from traditional biomass technologies and coal-based electricity generation, significant reductions in PM2.5 levels are achievable in 2030 and 2050. Effective mitigation of future air pollution in India requires adoption of aggressive prospective

An LUR/BME framework to estimate PM2.5 explained by on road mobile and stationary sources.

Science.gov (United States)

Reyes, Jeanette M; Serre, Marc L

2014-01-01

Knowledge of particulate matter concentrations Bayesian Maximum Entropy (BME) framework to estimate PM2.5 across the United States from 1999 to 2009. A cross-validation was done to determine the improvement of the estimate due to the LUR incorporation into BME. These results were applied to known diseases to determine predicted mortality coming from total PM2.5 as well as PM2.5 explained by major contributing sources. This method showed a mean squared error reduction of over 21.89% oversimple kriging. PM2.5 explained by on road mobile emissions and stationary emissions contributed to nearly 568,090 and 306,316 deaths, respectively, across the United States from 1999 to 2007.

The relationship between fine particulate matter (PM2.5) and schizophrenia severity.

Science.gov (United States)

Eguchi, Rika; Onozuka, Daisuke; Ikeda, Kouji; Kuroda, Kenji; Ieiri, Ichiro; Hagihara, Akihito

2018-04-23

Although particulate matter (PM) is reported to affect the rate of emergency admissions for schizophrenia, no study has examined the relationship between particulate matter less than 2.5 μm in diameter (PM 2.5 ) and the severity of schizophrenia. We obtained data on patients with schizophrenia at a psychiatric hospital, and on air pollution in Sakai, Japan between Feb 1, 2013 and April 30, 2016. Multivariate logistic regression analyses were used to estimate the relationship between PM 2.5 concentrations and scores on the Brief Psychiatric Rating Scale (BPRS) of schizophrenia patients at admission, with a lag of up to 7 days. During the study period, there were 1193 schizophrenia cases. The odds ratio (OR) for a BPRS score ≥ 50 at admission was 1.05 [95% confidence interval 1.00-1.10] and the effect of PM 2.5 concentration was significant for lag period of 2 days. The ORs associated with PM 2.5 concentration increased substantially for patients over 65 years of age. Ambient PM 2.5 concentration was associated with exacerbation of schizophrenia. Our results suggest that protection for several days should be considered for controlling PM 2.5 -related schizophrenia, especially among elderly patients.

Identification and elucidation of anthropogenic source contribution in PM10 pollutant: Insight gain from dispersion and receptor models.

Science.gov (United States)

Roy, Debananda; Singh, Gurdeep; Yadav, Pankaj

2016-10-01

Source apportionment study of PM 10 (Particulate Matter) in a critically polluted area of Jharia coalfield, India has been carried out using Dispersion model, Principle Component Analysis (PCA) and Chemical Mass Balance (CMB) techniques. Dispersion model Atmospheric Dispersion Model (AERMOD) was introduced to simplify the complexity of sources in Jharia coalfield. PCA and CMB analysis indicates that monitoring stations near the mining area were mainly affected by the emission from open coal mining and its associated activities such as coal transportation, loading and unloading of coal. Mine fire emission also contributed a considerable amount of particulate matters in monitoring stations. Locations in the city area were mostly affected by vehicular, Liquid Petroleum Gas (LPG) & Diesel Generator (DG) set emissions, residential, and commercial activities. The experimental data sampling and their analysis could aid understanding how dispersion based model technique along with receptor model based concept can be strategically used for quantitative analysis of Natural and Anthropogenic sources of PM 10 . Copyright © 2016. Published by Elsevier B.V.

A Comparison of the Health Effects of Ambient Particulate Matter Air Pollution from Five Emission Sources

Directory of Open Access Journals (Sweden)

Neil J. Hime

2018-06-01

Full Text Available This article briefly reviews evidence of health effects associated with exposure to particulate matter (PM air pollution from five common outdoor emission sources: traffic, coal-fired power stations, diesel exhaust, domestic wood combustion heaters, and crustal dust. The principal purpose of this review is to compare the evidence of health effects associated with these different sources with a view to answering the question: Is exposure to PM from some emission sources associated with worse health outcomes than exposure to PM from other sources? Answering this question will help inform development of air pollution regulations and environmental policy that maximises health benefits. Understanding the health effects of exposure to components of PM and source-specific PM are active fields of investigation. However, the different methods that have been used in epidemiological studies, along with the differences in populations, emission sources, and ambient air pollution mixtures between studies, make the comparison of results between studies problematic. While there is some evidence that PM from traffic and coal-fired power station emissions may elicit greater health effects compared to PM from other sources, overall the evidence to date does not indicate a clear ‘hierarchy’ of harmfulness for PM from different emission sources. Further investigations of the health effects of source-specific PM with more advanced approaches to exposure modeling, measurement, and statistics, are required before changing the current public health protection approach of minimising exposure to total PM mass.

Chemical Characterization of Outdoor and Subway Fine (PM2.5–1.0) and Coarse (PM10–2.5) Particulate Matter in Seoul (Korea) by Computer-Controlled Scanning Electron Microscopy (CCSEM)

Science.gov (United States)

Byeon, Sang-Hoon; Willis, Robert; Peters, Thomas M.

2015-01-01

Outdoor and indoor (subway) samples were collected by passive sampling in urban Seoul (Korea) and analyzed with computer-controlled scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (CCSEM-EDX). Soil/road dust particles accounted for 42%–60% (by weight) of fine particulate matter larger than 1 µm (PM2.5–1.0) in outdoor samples and 18% of PM2.5–1.0 in subway samples. Iron-containing particles accounted for only 3%–6% in outdoor samples but 69% in subway samples. Qualitatively similar results were found for coarse particulate matter (PM10–2.5) with soil/road dust particles dominating outdoor samples (66%–83%) and iron-containing particles contributing most to subway PM10–2.5 (44%). As expected, soil/road dust particles comprised a greater mass fraction of PM10–2.5 than PM2.5–1.0. Also as expected, the mass fraction of iron-containing particles was substantially less in PM10–2.5 than in PM2.5–1.0. Results of this study are consistent with known emission sources in the area and with previous studies, which showed high concentrations of iron-containing particles in the subway compared to outdoor sites. Thus, passive sampling with CCSEM-EDX offers an inexpensive means to assess PM2.5–1.0 and PM10-2.5 simultaneously and by composition at multiple locations. PMID:25689348

Chemical Characterization of Outdoor and Subway Fine (PM2.5–1.0 and Coarse (PM10–2.5 Particulate Matter in Seoul (Korea by Computer-Controlled Scanning Electron Microscopy (CCSEM

Directory of Open Access Journals (Sweden)

Sang-Hoon Byeon

2015-02-01

Full Text Available Outdoor and indoor (subway samples were collected by passive sampling in urban Seoul (Korea and analyzed with computer-controlled scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (CCSEM-EDX. Soil/road dust particles accounted for 42%–60% (by weight of fine particulate matter larger than 1 µm (PM2.5–1.0 in outdoor samples and 18% of PM2.5–1.0 in subway samples. Iron-containing particles accounted for only 3%–6% in outdoor samples but 69% in subway samples. Qualitatively similar results were found for coarse particulate matter (PM10–2.5 with soil/road dust particles dominating outdoor samples (66%–83% and iron-containing particles contributing most to subway PM10–2.5 (44%. As expected, soil/road dust particles comprised a greater mass fraction of PM10–2.5 than PM2.5–1.0. Also as expected, the mass fraction of iron-containing particles was substantially less in PM10–2.5 than in PM2.5–1.0. Results of this study are consistent with known emission sources in the area and with previous studies, which showed high concentrations of iron-containing particles in the subway compared to outdoor sites. Thus, passive sampling with CCSEM-EDX offers an inexpensive means to assess PM2.5–1.0 and PM10-2.5 simultaneously and by composition at multiple locations.

Assessment of annual air pollution levels with PM1, PM2.5, PM10 and associated heavy metals in Algiers, Algeria.

Science.gov (United States)

Talbi, Abdelhamid; Kerchich, Yacine; Kerbachi, Rabah; Boughedaoui, Ménouèr

2018-01-01

Concentrations of particulate matter less than 1  μm, 2.5  μm, 10 μm and their contents of heavy metals were investigated in two different stations, urban and roadside at Algiers (Algeria). Sampling was conducted during two years by a high volume samplers (HVS) equipped with a cascade impactor at four levels stage, for one year sampling. The characterization of the heavy metals associated to the particulate matter (PM) was carried out by X-Ray Fluorescence analysis (XRF). The annual average concentration of PM 1 , PM 2.5 and PM 10 in both stations were 18.24, 32.23 and 60.01 μg m -3 respectively. The PM 1 , PM 2.5 and PM 10 concentrations in roadside varied from 13.46 to 25.59 μg m -3 , 20.82-49.85 μg m -3 and 45.90-77.23 μg m -3 respectively. However in the urban station, the PM 1 , PM 2.5 and PM 10 concentrations varied from 10.45 to 26.24 μg m -3 , 18.53-47.58 μg m -3 and 43.8-91.62 μg m -3 . The heavy metals associated to the PM were confirmed by Scanning Electron Microscopy-Energy Dispersive X-Ray analyses (SEM-EDX). The different spots of PM 2.5 analysis by SEM-EDX shows the presence of nineteen elements with anthropogenic and natural origins, within the heavy metal detected, the lead was found with maximum of 5% (weight percent). In order to determine the source contributions of PM levels at the two sampling sites sampling, principal compound analysis (PCA) was applied to the collected data. Statistical analysis confirmed anthropogenic source with traffic being a significant source and high contribution of natural emissions. At both sites, the PM 2.5 /PM 10 ratio is lower than that usually recorded in developed countries. The study of the back-trajectories of the air masses starting from Sahara shows that desert dust influences the concentration and the composition of the PM measured in Algiers. Copyright © 2017 Elsevier Ltd. All rights reserved.

PM2.5 and PM10 Emission from agricultural soils by wind erosion

Science.gov (United States)

Soil tillage and wind erosion are a major source of particulate matter less than 2.5 and 10 µm (PM2.5 and PM10) emission from cultivated soil. Fifteen cultivated soils collected from 5 states were tested as crushed (<2.0 mm) and uncrushed (natural aggregation) at 8, 10, and 13 m s-1 wind velocity in...

Implementation and evaluation of PM2.5 source contribution ...

Science.gov (United States)

Source culpability assessments are useful for developing effective emissions control programs. The Integrated Source Apportionment Method (ISAM) has been implemented in the Community Multiscale Air Quality (CMAQ) model to track contributions from source groups and regions to ambient levels and deposited amounts of primary and secondary inorganic PM2.5. Confidence in this approach is established by comparing ISAM source contribution estimates to emissions zero-out simulations recognizing that these approaches are not always expected to provide the same answer. The comparisons are expected to be most similar for more linear processes such as those involving primary emissions of PM2.5 and most different for non-linear systems like ammonium nitrate formation. Primarily emitted PM2.5 (e.g. elemental carbon), sulfur dioxide, ammonia, and nitrogen oxide contribution estimates compare well to zero-out estimates for ambient concentration and deposition. PM2.5 sulfate ion relationships are strong, but nonlinearity is evident and shown to be related to aqueous phase oxidation reactions in the host model. ISAM and zero-out contribution estimates are less strongly related for PM2.5 ammonium nitrate, resulting from instances of non-linear chemistry and negative responses (increases in PM2.5 due to decreases in emissions). ISAM is demonstrated in the context of an annual simulation tracking well characterized emissions source sectors and boundary conditions shows source contri

Assessment of Contribution of Contemporary Carbon Sources to Size-Fractionated Particulate Matter and Time-Resolved Bulk Particulate Matter Using the Measurement of Radiocarbon

Energy Technology Data Exchange (ETDEWEB)

Hwang, H M; Young, T M; Buchholz, B A

2009-04-16

This study was motivated by a desire to improve understanding of the sources contributing to the carbon that is an important component of airborne particulate matter (PM). The ultimate goal of this project was to lay a ground work for future tools that might be easily implemented with archived or routinely collected samples. A key feature of this study was application of radiocarbon measurement that can be interpreted to indicate the relative contributions from fossil and non-fossil carbon sources of atmospheric PM. Size-resolved PM and time-resolved PM{sub 10} collected from a site in Sacramento, CA in November 2007 (Phase I) and March 2008 (Phase II) were analyzed for radiocarbon and source markers such as levoglucosan, cholesterol, and elemental carbon. Radiocarbon data indicates that the contributions of non-fossil carbon sources were much greater than that from fossil carbon sources in all samples. Radiocarbon and source marker measurements confirm that a greater contribution of non-fossil carbon sources in Phase I samples was highly likely due to residential wood combustion. The present study proves that measurement of radiocarbon and source markers can be readily applied to archived or routinely collected samples for better characterization of PM sources. More accurate source apportionment will support ARB in developing more efficient control strategies.

On the origin and variability of suspended particulate matter (PM1, PM2.5 and PM10) concentrations in Cyprus.

Science.gov (United States)

Pikridas, Michael; Vrekoussis, Mihalis; Mihalopoulos, Nikolaos; Kizas, Christos; Savvides, Chrysanthos; Sciare, Jean

2017-04-01

The Eastern Mediterranean (EM) lies at the crossroad of three different continents (Europe, Asia, and Africa). EM is a densely populated region including several cities with 3M inhabitants or more (e.g. Athens, Istanbul, Izmir, and Cairo). It has been identified as the most polluted area in Europe with respect to particulate matter (PM) mainly due to the combination of high photochemical activity, which causes pollutants to oxidize and partitioning in the particle phase, with the elevated pollutants emissions from neighboring regions. In addition, the proximity to Africa and the Middle East allows frequent transport of dust particles. At the center of the Eastern Mediterranean lies the island of Cyprus, which has received very little attention regarding its PM levels despite being the location in Europe most frequently impacted by air masses from the Middle East. Herewith, we present a historical PM archive that spans 2 decades. It involves ongoing monitoring on a daily basis of particulate matter with diameters smaller than 10 μm (PM10), 2.5 μm (PM2.5), and 1 μm (PM1) conducted in at least one, of the 12 currently existing air quality stations in Cyprus since 1997, 2005, and 2009, respectively. The most extended PM datasets correspond a) to the Agia Marina Xyliatou (AMX) monitoring station established at a remote area at the foothills of mount Troodos and b) that of the inland capital, Nicosia. Based on this long-term dataset, the diurnal, temporal and annual variability is assessed. Prior to 2010, PM10 concentration at all sites remained relatively constant, but at different levels, violating the annual EU legislated PM10 limit of 40 μg m-3. Since 2010, coarse mode levels have decreased at all sites. The reported decrease was equal to 30% at AMX. As a result, since 2010 the observed levels comply with the EU legislation threshold. Satellite observations of Aerosol Optical Thickness (AOT) Moderate Resolution Imaging Spectroradiometer (MODIS) onboard NASA

AIRUSE-LIFE+: a harmonized PM speciation and source apportionment in five southern European cities

Science.gov (United States)

Amato, Fulvio; Alastuey, Andrés; Karanasiou, Angeliki; Lucarelli, Franco; Nava, Silvia; Calzolai, Giulia; Severi, Mirko; Becagli, Silvia; Gianelle, Vorne L.; Colombi, Cristina; Alves, Celia; Custódio, Danilo; Nunes, Teresa; Cerqueira, Mario; Pio, Casimiro; Eleftheriadis, Konstantinos; Diapouli, Evangelia; Reche, Cristina; Cruz Minguillón, María; Manousakas, Manousos-Ioannis; Maggos, Thomas; Vratolis, Stergios; Harrison, Roy M.; Querol, Xavier

2016-03-01

The AIRUSE-LIFE+ project aims at characterizing similarities and heterogeneities in particulate matter (PM) sources and contributions in urban areas from southern Europe. Once the main PMx sources are identified, AIRUSE aims at developing and testing the efficiency of specific and non-specific measures to improve urban air quality. This article reports the results of the source apportionment of PM10 and PM2.5 conducted at three urban background sites (Barcelona, Florence and Milan, BCN-UB, FI-UB and MLN-UB), one suburban background site (Athens, ATH-SUB) and one traffic site (Porto, POR-TR). After collecting 1047 PM10 and 1116 PM2.5 24 h samples during 12 months (from January 2013 on) simultaneously at the five cities, these were analysed for the contents of OC, EC, anions, cations, major and trace elements and levoglucosan. The USEPA PMF5 receptor model was applied to these data sets in a harmonized way for each city. The sum of vehicle exhaust (VEX) and non-exhaust (NEX) contributes between 3.9 and 10.8 µg m-3 (16-32 %) to PM10 and 2.3 and 9.4 µg m-3 (15-36 %) to PM2.5, although a fraction of secondary nitrate is also traffic-related but could not be estimated. Important contributions arise from secondary particles (nitrate, sulfate and organics) in PM2.5 (37-82 %) but also in PM10 (40-71 %), mostly at background sites, revealing the importance of abating gaseous precursors in designing air quality plans. Biomass burning (BB) contributions vary widely, from 14-24 % of PM10 in POR-TR, MLN-UB and FI-UB, 7 % in ATH-SUB, to levels increase on an annual basis by 1-9 µg m-3 due to biomass burning influence. Other significant sources are the following. - Local dust, 7-12 % of PM10 at SUB and UB sites and 19 % at the TR site, revealing a contribution from road dust resuspension. In PM2.5 percentages decrease to 2-7 % at SUB-UB sites and 15 % at the TR site. - Industry, mainly metallurgy, contributing 4-11 % of PM10 (5-12 % in PM2.5), but only at BCN-UB, POR-TR and MLN

[Sampling methods for PM2.5 from stationary sources: a review].

Science.gov (United States)

Jiang, Jing-Kun; Deng, Jian-Guo; Li, Zhen; Li, Xing-Hua; Duan, Lei; Hao, Ji-Ming

2014-05-01

The new China national ambient air quality standard has been published in 2012 and will be implemented in 2016. To meet the requirements in this new standard, monitoring and controlling PM2,,5 emission from stationary sources are very important. However, so far there is no national standard method on sampling PM2.5 from stationary sources. Different sampling methods for PM2.5 from stationary sources and relevant international standards were reviewed in this study. It includes the methods for PM2.5 sampling in flue gas and the methods for PM2.5 sampling after dilution. Both advantages and disadvantages of these sampling methods were discussed. For environmental management, the method for PM2.5 sampling in flue gas such as impactor and virtual impactor was suggested as a standard to determine filterable PM2.5. To evaluate environmental and health effects of PM2.5 from stationary sources, standard dilution method for sampling of total PM2.5 should be established.

A multivariate study for characterizing particulate matter (PM(10), PM(2.5), and PM(1)) in Seoul metropolitan subway stations, Korea.

Science.gov (United States)

Kwon, Soon-Bark; Jeong, Wootae; Park, Duckshin; Kim, Ki-Tae; Cho, Kyung Hwa

2015-10-30

Given that around eight million commuters use the Seoul Metropolitan Subway (SMS) each day, the indoor air quality (IAQ) of its stations has attracted much public attention. We have monitored the concentration of particulate matters (PMx) (i.e., PM10, PM2.5, and PM1) in six major transfer stations per minute for three weeks during the summer, autumn, and winter in 2014 and 2015. The data were analyzed to investigate the relationship between PMx concentration and multivariate environmental factors using statistical methods. The average PM concentration observed was approximately two or three times higher than outdoor PM10 concentration, showing similar temporal patterns at concourses and platforms. This implies that outdoor PM10 is the most significant factor in controlling indoor PM concentration. In addition, the station depth and number of trains passing through stations were found to be additional influences on PMx. Principal component analysis (PCA) and self-organizing map (SOM) were employed, through which we found that the number of trains influences PM concentration in the vicinity of platforms only, and PMx hotspots were determined. This study identifies the external and internal factors affecting PMx characteristics in six SMS stations, which can assist in the development of effective IAQ management plans to improve public health. Copyright © 2015 Elsevier B.V. All rights reserved.

Characteristics and source apportionment of PM1 emissions at a roadside station.

Science.gov (United States)

Cheng, Y; Zou, S C; Lee, S C; Chow, J C; Ho, K F; Watson, J G; Han, Y M; Zhang, R J; Zhang, F; Yau, P S; Huang, Y; Bai, Y; Wu, W J

2011-11-15

The mass concentrations of PM(1) (particles less than 1.0 μm in aerodynamic diameter), organic carbon (OC), elemental carbon (EC), water-soluble ions, and up to 25 elements were reported for 24h aerosol samples collected every sixth day at a roadside sampling station in Hong Kong from October 2004 to September 2005. Annual average PM(1) mass concentration was 44.5 ± 19.5 μg m(-3). EC, OM (organic matter, OC × 1.2), and SO(4)(=) were the dominant components, accounting for ∼ 36%, ∼ 26%, and ∼ 24% of PM(1), respectively. Other components, i.e., NO(3)(-), NH(4)(+), geological material, trace elements and unidentified material, comprised the remaining ∼ 14%. Annual average OC/EC ratio (0.6 ± 0.3) was low, indicating that primary vehicle exhaust was the major source of carbonaceous aerosols. The seasonal variations of pollutants were due to gas-particle partitioning processes or a change in air mass rather than secondary aerosol produced locally. Vehicle exhaust, secondary aerosols, and waste incinerator/biomass burning were dominant air pollution sources, accounting for ∼ 38%, ∼ 22% and ∼ 16% of PM(1), respectively. Pollution episodes during summer (May-August) which were frequently accompanied by tropical storms or typhoons were dominated by vehicle emissions. During winter (November-February) pollution episodes coincided with northeasterly monsoons were characterized by secondary aerosols and incinerator/biomass burning emissions. Copyright © 2011 Elsevier B.V. All rights reserved.

PM10 source apportionment study in Pleasant Valley, Nevada

International Nuclear Information System (INIS)

Egami, R.T.; Chow, J.C.; Watson, J.G.; DeLong, T.

1990-01-01

A source apportionment study was conducted between March 18 and April 4, 1988, at Pleasant Valley, Nevada, to evaluate air pollutant concentrations to which community residents were exposed and the source contributions to those pollutants. Daily PM 10 samples were taken for chemical speciation of 40 trace elements, ions, and organic and elemental carbon. This paper reports that the objectives of this case study are: to determine the emissions source composition of the potential upwind source, a geothermal plant; to measure the ambient particulate concentration and its chemical characteristics in Pleasant Valley; and to estimate the contributions of different emissions sources to PM 10 . The study found that: particulate emissions from the geothermal cooling-tower plume consisted primarily of sulfate, ammonia, chloride, and trace elements; no significant quantities of toxic inorganic species were found in the ambient air; ambient PM 10 concentrations in Pleasant Valley were within Federal standards; and source contribution to PM 10 were approximately 60% geological material; 20% motor vehicle exhaust; and 10% cooling-tower plume

2005-2014 trends of PM10 source contributions in an industrialized area of southern Spain.

Science.gov (United States)

Li, Jiwei; Chen, Bing; de la Campa, Ana M Sánchez; Alastuey, Andrés; Querol, Xavier; de la Rosa, Jesus D

2018-05-01

Particulate matter with a diameter of 10 μm or less (PM10) using receptor modelling was determined at an urban (La Linea, LL) and an industrial area (Puente Mayorga, PMY) in Southern Spain with samples collected during 2005-2014. The concentrations of PM10 had been decreasing at both sites in three distinctive periods: 1) the initial PM10 levels approached or exceeded the Spain and EU PM10 annual guidelines of 40 μg/m 3 during 2005-2007 at LL and 2005-2009 at PMY; 2) then PM10 dropped by 25%-∼30 μg/m 3 during 2008-2011 at LL and during 2010-2011 at PMY; 3) since 2012, the PM10 concentrations gradually decreased to major elements. These PM components generally showed a decrease trend, in accord with the trend of PM10 reduction. A PMF model identified seven sources to PM10 contributions. Secondary sulfate, soil/urban/construction dust, and secondary nitrate showed significantly decreasing trends with reduction of 40-60% comparing to the initial levels. The road traffic contribution decreased by 14% from the first to third period. However, sea salt, oil combustion, and industrial metallurgical process had relative stable contributions. These source contribution changes are reasonably governed by the PM emission abatement actions implemented during the past decade, as well as the financial crisis, that accounted for a significant decrease of PM pollution in Southern Spain. We identified that the mitigation efforts on industry, fossil fuel combustion, and urban transportation during the past decade were successful for air quality improvement in a highly industrialized area in Southern Spain. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization of Fine Particulate Matter (PM) and Secondary PM Precursor Gases in the Mexico City Metropolitan Area

Science.gov (United States)

Molina, Luisa T.; Volkamer, Rainer; de Foy, Benjamin; Lei, Wenfang; Zavala, Miguel; Velasco, Erik; Molina; Mario J.

2008-10-31

This project was one of three collaborating grants funded by DOE/ASP to characterize the fine particulate matter (PM) and secondary PM precursors in the Mexico City Metropolitan Area (MCMA) during the MILAGRO Campaign. The overall effort of MCMA-2006, one of the four components, focused on i) examination of the primary emissions of fine particles and precursor gases leading to photochemical production of atmospheric oxidants and secondary aerosol particles; ii) measurement and analysis of secondary oxidants and secondary fine PM production, with particular emphasis on secondary organic aerosol (SOA), and iii) evaluation of the photochemical and meteorological processes characteristic of the Mexico City Basin. The collaborative teams pursued the goals through three main tasks: i) analyses of fine PM and secondary PM precursor gaseous species data taken during the MCMA-2002/2003 campaigns and preparation of publications; ii) planning of the MILAGRO Campaign and deployment of the instrument around the MCMA; and iii) analysis of MCMA-2006 data and publication preparation.

The representation of dust transport and missing urban sources as major issues for the simulation of PM episodes in a Mediterranean area

Directory of Open Access Journals (Sweden)

E. Flaounas

2009-10-01

Full Text Available Due to its adverse effects on human health, atmospheric particulate matter (PM constitutes a growing challenge for air quality management. It is also a complex subject of study. The understanding of its atmospheric evolution is indeed made difficult by the wide number of sources and the numerous processes that govern its evolution in the troposphere. As a consequence, the representation of particulate matter in chemistry-transport models needs to be permanently evaluated and enhanced in order to refine our comprehension of PM pollution events and to propose consistent environmental policies. The study presented here focuses on two successive summer particulate pollution episodes that occurred on the French Mediterranean coast. We identify and analyze the constitutive elements of the first and more massive episode and we discuss their representation within a eulerian model.

The results show that the model fails in reproducing the variability and the amplitude of dust import from western Africa, and that it constitutes a strong bias in PM daily forecasts. We then focus on the lack of diurnal variability in the model, which is attributed to missing urban sources in standard emission inventories, and notably the resuspension of particles by urban road traffic. Through a sensitivity study based on PM and NO_x measurements, we assess the sensitivity of PM to local emissions and the need to reconsider road traffic PM sources. In parallel, by coupling the CHIMERE-DUST model outputs to our simulation, we show that the representation of transcontinental dust transport allows a much better representation of atmospheric particles in southern France, and that it is needed in the frame of air quality management for the quantification of the anthropogenic part of particulate matter pollution.

Characterization and sources of air particulate matter at Kwabenya, near Accra, Ghana

International Nuclear Information System (INIS)

Aboh, I. J. K.

2009-01-01

well but during the Rainy season S did not correlate with V and Br. This could serve as possible source indicators. The BC concentration in the fine fraction (ranging from 0.01 to 5.97 µgm') was generally higher than in the coarse fraction and comparable to data from some developed countries. A receptor model using principal component and regression analysis was used to identify sources contributing to the air particulate matter at Kwabenya. The species used in the model were mass, BC and elemental concentrations. The following major sources were identified in the coarse aerosol: Soil/Dust, Biomass/LDT and Sea aerosol. In the fine aerosol the following sources were identified: Soil/Dust, Biomass/LDT and some industrial sources. The contribution of the sources to the PM load varied from season to season, There was very good agreement between the experimental and model data (mass, BC and elemental concentrations). Comparing the data with WHO limit (50 ugm 3 for 24-hour mean) and Ghana EPA guideline limit (70 ugm 3 for 24 hours) for PM 10 , a total of 185 and 130 days respectively out of 216 days had values above these limits. For PM 2 . 5 a total of 60 days had values exceeding the WHO limit (25 µgm 3 for 24-hour mean). The levels of S, Ni and Pb were also comparable to industrialised countries. There is the need for some mitigation measures to curb the emission of these elements and fine BC. (au)

Elemental characterization of New Year's Day PM10 and PM2.2 particulates matter at several sites in Metro Manila

International Nuclear Information System (INIS)

Santos, Flora L.; Pabroa, Preciosa Corazon B.; Morco, Ryan P.; Racho, Joseph Michael D.

2007-01-01

In the Philippines, it has been a yearly tradition to welcome the coming of the New Year with the loudest noise as can be achieved. Firecrackers and fireworks have been a necessity for Filipinos during this time despite bans on the use of most of these and despite the Department of Health (DOH) campaign to use alternative safe practices to welcome the New Year. Data for PM 10 samples (fractionated as PM 10-2.2 or the course fraction and PM2.2 or the fine fraction) collected in four PNRI sampling sites in Metro Manila show the air pollution impacts of fireworks on New Year's Eve. Samples were collected from 1998 to 2006 using a Gent dichotomous sampler in connection with the PNRI project P articulate Matter Source Apportionment Using Nuclear and Related Analytical Techniques . Particulate mass was determined by gravimetry. Elemental analysis of the air filters was done using X-ray Fluorescence Spectrometry (X RF) or Particle induced X-ray Emission (PIXE), multielemental non-destructive nuclear analytical techniques. Black carbon was analyzed using reflectometry. PM 10 values increased by two to four times the usual averages (36.4 to 55.4 ug/cum) and in 2002 even exceeded the PNAAQ short-term guideline value of 150 ug/cum at the ADMU sampling station. PM2.2 values increased by two to six times the usual averages (15 to 28 ug/cum), even many times exceeding US EPA short-term guideline value of 65 ug/cum. The increase in the particulate mass of New Year's Day samples can be attributed more to an increase in the metal pollutants rather than the black carbon, with higher contribution to the fine fraction. Increase in the elemental concentrations of Al, S, Cl, K, Ba, Sr, Ti, V, Mn, Cu and Pb were observed with the highest contribution from K. Results show that the usual practices of burning firecrackers and fireworks during New Year's day celebration is a very strong source of air pollution which contributes significantly high amount of metal pollutants in the air

Temporal variations and spatial distribution of ambient PM{sub 2.2} and PM{sub 1} concentrations in Dhaka, Bangladesh

Energy Technology Data Exchange (ETDEWEB)

Begum, Bilkis A. [Chemistry Division, Atomic Energy Centre, P.O. Box-164, Dhaka (Bangladesh); Biswas, Swapan K. [Chemistry Division, Atomic Energy Centre, P.O. Box-164, Dhaka (Bangladesh); Hopke, Philip K. [Department of Chemical Engineering, Clarkson University, Potsdam, NY 13699-5810 (United States)]. E-mail: hopkepk@clarkson.edu

2006-04-01

Concentrations and characteristics of airborne particulate matter (PM{sub 1}, PM{sub 2.2} and BC) on air quality have been studied at two air quality-monitoring stations in Dhaka, the capital of Bangladesh. One site is at the Farm Gate area, a hot spot with very high pollutant concentrations because of its proximity to major roadways. The other site is at a semi-residential area located at the Atomic Energy Centre, Dhaka Campus, (AECD) with relatively less traffic. The samples were collected using a 'Gent' stacked filter unit in two fractions of 0-2.2 {mu}m and 2.2-10 {mu}m sizes. Samples of fine (PM{sub 2.2}) and coarse (PM{sub 2.2-1}) airborne particulate matter fractions collected from 2000 to 2003 were studied. It has been observed that fine particulate matter has a decreasing trend, from prior year measurements, because of Government policy interventions like phase-wise plans to take two-stroke three-wheelers off the roads in Dhaka and finally banned from January 1, 2003. Other policy interventions were banning of old buses and trucks to ply on Dhaka city promotion of the using compressed natural gas (CNG), introducing air pollution control devices in vehicles, etc. It was found that both local (mostly from vehicular emissions) and possibly some regional emission sources are responsible for high PM{sub 2.2} and BC concentrations in Dhaka. PM{sub 2.2}, PM{sub 2.2-1} and black carbon concentration levels depend on the season, wind direction and wind speed. Transport related emissions are the major source of BC and long-range transportation from fossil fuel related sources and biomass burning could be another substantial source of BC.

Temporal variations and spatial distribution of ambient PM{sub 2.2} and PM{sub 10} concentrations in Dhaka, Bangladesh

Energy Technology Data Exchange (ETDEWEB)

Begum, Bilkis A.; Biswas, Swapan K. [Chemistry Division, Atomic Energy Centre, P.O. Box-164, Dhaka (Bangladesh); Hopke, Philip K. [Department of Chemical Engineering, Clarkson University, Potsdam, NY 13699-5810 (United States)

2006-04-01

Concentrations and characteristics of airborne particulate matter (PM{sub 10}, PM{sub 2.2} and BC) on air quality have been studied at two air quality-monitoring stations in Dhaka, the capital of Bangladesh. One site is at the Farm Gate area, a hot spot with very high pollutant concentrations because of its proximity to major roadways. The other site is at a semi-residential area located at the Atomic Energy Centre, Dhaka Campus, (AECD) with relatively less traffic. The samples were collected using a 'Gent' stacked filter unit in two fractions of 0-2.2 {mu}m and 2.2-10 {mu}m sizes. Samples of fine (PM{sub 2.2}) and coarse (PM{sub 2.2-10}) airborne particulate matter fractions collected from 2000 to 2003 were studied. It has been observed that fine particulate matter has a decreasing trend, from prior year measurements, because of Government policy interventions like phase-wise plans to take two-stroke three-wheelers off the roads in Dhaka and finally banned from January 1, 2003. Other policy interventions were banning of old buses and trucks to ply on Dhaka city promotion of the using compressed natural gas (CNG), introducing air pollution control devices in vehicles, etc. It was found that both local (mostly from vehicular emissions) and possibly some regional emission sources are responsible for high PM{sub 2.2} and BC concentrations in Dhaka. PM{sub 2.2}, PM{sub 2.2-10} and black carbon concentration levels depend on the season, wind direction and wind speed. Transport related emissions are the major source of BC and long-range transportation from fossil fuel related sources and biomass burning could be another substantial source of BC. (author)

Chemical Composition and Source Apportionment of high temporal resolution PM1 data for January-August 2017 in Delhi, India

Science.gov (United States)

Bhandari, S.; Wang, D. S.; Gani, S.; Seraj, S.; Arub, Z.; Habib, G.; Apte, J.; Hildebrandt Ruiz, L.

2017-12-01

Exposure to fine particulate matter (PM) poses significant health risks, especially to residents in heavily populated areas. The current understanding of the sources and dynamics of PM pollution in developing countries like India is limited. Delhi, India is the second most populated city in the world that has extremely high winter PM concentrations and frequent severe pollution episodes. This study reports on composition measurements of submicron aerosol at 1 minute time resolution from January to August of 2017, collected at the Indian Institute of Technology Delhi using an Aerodyne Aerosol Chemical Speciation Monitor (ACSM) and black carbon (BC) measurements using an Aethalometer. Source apportionment was conducted on organic and inorganic mass spectra measured by the ACSM and black carbon data measured using Positive Matrix Factorization (PMF). High concentrations of particulate matter were observed with total PM1 at times exceeding 200 µg m-3 in winter. A significant drop in PM1 concentrations was observed in the winter-spring transition. As observed elsewhere, organic species dominated the submicron mass, contributing 60% of the total mass over the duration of the campaign. However, this fractional contribution varied substantially over the day: from 48% early in the morning to 73% late at night. Along with diurnal variation in total PM1 mass loadings, particulate chloride levels also exhibited a strong diurnal cycle, with concentrations as high as 50 µg m-3 observed in the early mornings of January 2017. Literature review on identification of winter chloride sources in Delhi points to local and regional sources such as biomass/open-waste burning and coal combustion. PMF receptor modeling identified several factors with distinct diurnal patterns. While hydrocarbon-like organic aerosol (HOA) factor has the largest mass fraction contribution, PMF results consistently suggest chloride presence as attributable to ammonium chloride. Interestingly, aerosol

ASSOCIATION OF PARTICULATE MATTER (PM WITH RESPIRATORY SYMPTOMS AMONG CHILDREN IN SELECTED PRIMARY SCHOOLS IN PAHANG

Directory of Open Access Journals (Sweden)

Maryam

2018-01-01

Full Text Available Particulate matter (PM is one of the primary pollutants found in the indoor environment. It can cause deterioration of the indoor air quality (IAQ and is often linked with adverse health effects especially towards susceptible subgroup of the population like children. School children are exposed to PM inside the classroom, as this indoor PM may originate from both indoor and outdoor sources. Furthermore, ambient surrounding could be one of the major factors that contribute to its high concentration, specifically for school environment like government-subsidized schools in Malaysia whereby the schools are using natural ventilation systems to control the thermal comfort inside the classrooms. Hence the infiltration of outdoor PM into the indoor is probably high and significant. The high concentration of PM may affect the children’s health and learning performances. Due to this reason, it is important to study the effects of PM towards children. Thus, this study aims to assess the concentrations of PM and selected IAQ parameters in the school indoor environment with distinct background characteristics including residential, industrial, and rural areas. PM and IAQ parameters (temperature, relative humidity (RH, carbon monoxide (CO and carbon dioxide (CO2 were assessed for 8-hours duration via DustMate Environmental Dust Detector (Turnkey Instruments, USA and VelociCalc® Multi-Function Ventilation Meter 9565 (TSI®, USA respectively, during occupied and non-occupied time in the classrooms. Second, considering the children’s prolonged and repetitive exposure towards PM in school indoor environment and their body sensitivity, this study also screened for the prevalence of non-specific respiratory disease (NSRD and persistent cough and phlegm (PCP among children via structured questionnaire developed by American Thoracic Society’s Division of Lung Diseases (ATS-DLD-78-C. Higher concentrations of PM and prevalence of respiratory symptoms in the

Quantification of vehicle fleet PM_1_0 particulate matter emission factors from exhaust and non-exhaust sources using tunnel measurement techniques

International Nuclear Information System (INIS)

Lawrence, Samantha; Sokhi, Ranjeet; Ravindra, Khaiwal

2016-01-01

Road tunnels act like large laboratories; they provide an excellent environment to quantify atmospheric particles emission factors from exhaust and non-exhaust sources due to their known boundary conditions. Current work compares the High Volume, Dichotomous Stacked Filter Unit and Partisol Air Sampler for coarse, PM_1_0 and PM_2_._5 particle concentration measurement and found that they do not differ significantly (p = 95%). PM_2_._5 fraction contributes 66% of PM_1_0 proportions and significantly influenced by traffic (turbulence) and meteorological conditions. Mass emission factors for PM_1_0 varies from 21.3 ± 1.9 to 28.8 ± 3.4 mg/vkm and composed of Motorcycle (0.0003–0.001 mg/vkm), Cars (26.1–33.4 mg/vkm), LDVs (2.4–3.0 mg/vkm), HDVs (2.2–2.8 mg/vkm) and Buses (0.1 mg/vkm). Based on Lawrence et al. (2013), source apportionment modelling, the PM_1_0 emission of brake wear (3.8–4.4 mg/vkm), petrol exhaust (3.9–4.5 mg/vkm), diesel exhaust (7.2–8.3 mg/vkm), re-suspension (9–10.4 mg/vkm), road surface wear (3.9–4.5 mg/vkm), and unexplained (7.2 mg/vkm) were also calculated. The current study determined that the combined non-exhaust fleet PM_1_0 emission factor (16.7–19.3 mg/vkm) are higher than the combined exhaust emission factor (11.1–12.8 mg/vkm). Thus, highlight the significance of non-exhaust emissions and the need for legislation and abatement strategies to reduce their contributions to ambient PM concentrations. - Highlights: • Calculations of exhaust/non-exhaust particulate emission factors using tunnel sampling and source apportionment techniques. • Non-exhaust emission dominates in the fine particle fraction, considered responsible for adverse human health impacts. • Emission factors for non-exhaust sources (e.g. tyre and brake) were calculated. • Fleet source PM_1_0 emission factor were also calculated, which can be used in dispersion modelling and health risk assessment. • Tukey mean

Establishing a link between vehicular PM sources and PM measurements in urban street canyons.

Science.gov (United States)

Eisner, Alfred D; Richmond-Bryant, Jennifer; Wiener, Russell W; Hahn, Intaek; Drake-Richman, Zora E; Ellenson, William D

2009-12-01

The Brooklyn Traffic Real-Time Ambient Pollutant Penetration and Environmental Dispersion (B-TRAPPED) study, conducted in Brooklyn, NY, USA, in 2005, was designed with multiple goals in mind, two of which were contaminant source characterization and street canyon transport and dispersion monitoring. In the portion of the study described here, synchronized wind velocity and azimuth as well as particulate matter (PM) concentrations at multiple locations along 33rd Street were used to determine the feasibility of using traffic emissions in a complex urban topography as a sole tracer for studying urban contaminant transport. We demonstrate in this paper that it is possible to link downwind concentrations of contaminants in an urban street canyon to the vehicular traffic cycle using Eigen-frequency analysis. In addition, multivariable circular histograms are used to establish directional frequency maxima for wind velocity and contaminant concentration.

PM(10) episodes in Greece: Local sources versus long-range transport-observations and model simulations.

Science.gov (United States)

Matthaios, Vasileios N; Triantafyllou, Athanasios G; Koutrakis, Petros

2017-01-01

Periods of abnormally high concentrations of atmospheric pollutants, defined as air pollution episodes, can cause adverse health effects. Southern European countries experience high particulate matter (PM) levels originating from local and distant sources. In this study, we investigated the occurrence and nature of extreme PM 10 (PM with an aerodynamic diameter ≤10 μm) pollution episodes in Greece. We examined PM 10 concentration data from 18 monitoring stations located at five sites across the country: (1) an industrial area in northwestern Greece (Western Macedonia Lignite Area, WMLA), which includes sources such as lignite mining operations and lignite power plants that generate a high percentage of the energy in Greece; (2) the greater Athens area, the most populated area of the country; and (3) Thessaloniki, (4) Patra, and (5) Volos, three large cities in Greece. We defined extreme PM 10 pollution episodes (EEs) as days during which PM 10 concentrations at all five sites exceeded the European Union (EU) 24-hr PM 10 standards. For each EE, we identified the corresponding prevailing synoptic and local meteorological conditions, including wind surface data, for the period from January 2009 through December 2011. We also analyzed data from remote sensing and model simulations. We recorded 14 EEs that occurred over 49 days and could be grouped into two categories: (1) Local Source Impact (LSI; 26 days, 53%) and (2) African Dust Impact (ADI; 23 days, 47%). Our analysis suggested that the contribution of local sources to ADI EEs was relatively small. LSI EEs were observed only in the cold season, whereas ADI EEs occurred throughout the year, with a higher frequency during the cold season. The EEs with the highest intensity were recorded during African dust intrusions. ADI episodes were found to contribute more than local sources in Greece, with ADI and LSI fraction contribution ranging from 1.1 to 3.10. The EE contribution during ADI fluctuated from 41 to 83 �

Modelling street level PM10 concentrations across Europe: source apportionment and possible futures

Science.gov (United States)

Kiesewetter, G.; Borken-Kleefeld, J.; Schöpp, W.; Heyes, C.; Thunis, P.; Bessagnet, B.; Terrenoire, E.; Fagerli, H.; Nyiri, A.; Amann, M.

2015-02-01

Despite increasing emission controls, particulate matter (PM) has remained a critical issue for European air quality in recent years. The various sources of PM, both from primary particulate emissions as well as secondary formation from precursor gases, make this a complex problem to tackle. In order to allow for credible predictions of future concentrations under policy assumptions, a modelling approach is needed that considers all chemical processes and spatial dimensions involved, from long-range transport of pollution to local emissions in street canyons. Here we describe a modelling scheme which has been implemented in the GAINS integrated assessment model to assess compliance with PM10 (PM with aerodynamic diameter dispersion calculations, and a traffic increment calculation wherever applicable. At each monitoring station fulfilling a few data coverage criteria, measured concentrations in the base year 2009 are explained to the extent possible and then modelled for the past and future. More than 1850 monitoring stations are covered, including more than 300 traffic stations and 80% of the stations which exceeded the EU air quality limit values in 2009. As a validation, we compare modelled trends in the period 2000-2008 to observations, which are well reproduced. The modelling scheme is applied here to quantify explicitly source contributions to ambient concentrations at several critical monitoring stations, displaying the differences in spatial origin and chemical composition of urban roadside PM10 across Europe. Furthermore, we analyse the predicted evolution of PM10 concentrations in the European Union until 2030 under different policy scenarios. Significant improvements in ambient PM10 concentrations are expected assuming successful implementation of already agreed legislation; however, these will not be large enough to ensure attainment of PM10 limit values in hot spot locations such as Southern Poland and major European cities. Remaining issues are

Sources of ambient concentrations and chemical composition of PM 2.5-0.1 in Cork Harbour, Ireland

Science.gov (United States)

Hellebust, S.; Allanic, A.; O'Connor, I. P.; Jourdan, C.; Healy, D.; Sodeau, J. R.

2010-02-01

Particulate matter (PM 10-2.5 and PM 2.5-0.1) has been collected over a period of one year in Cork Harbour, Ireland, using a high-volume cascade impactor and polyurethane foam collection substrate. Collected PM 2.5-0.1 was analysed for water-soluble inorganic ions and metal content using ion chromatography and inductively coupled plasma-optical emission spectroscopy. On average approximately 50% by mass of the chemical content of PM was identified. The motivation for the study was to assess the potential impact of shipping emissions on air quality in Cork Harbour and City, with a view to informing public health impacts. The average ambient concentration of PM 10 between May 2007 and April 2008 was 4.6 µgm - 3 and the maximum concentration measured in one sample, representing a 4 day collection period, was 16 µgm - 3 . The major inorganic constituents identified in PM collected in Haulbowline Island in Cork Harbour were sulfate, ammonium, nitrate, chloride and sodium ions, which were mainly attributable to sea salt and secondary inorganic aerosols from regional sources. The results were analysed by principal component analysis for the purpose of source apportionment. Four factors were identified explaining over 80% of the data set variance. The factors were: shipping, sea salt, crustal material and secondary inorganic aerosols (SIA). The smaller size fraction was frequently observed to dominate, as the average concentration was 2.77 µgm - 3 for PM 2.5-0.1 compared to 1.9 µgm - 3 for PM 10-2.5. Fresh ship plumes were not found to make a significant contribution to primary PM 2.5-0.1 concentrations adjacent to the shipping channel. However, this was partially attributed to the ultrafine nature of ship emissions and the majority of the toxic metal content was attributed to emissions associated with heavy oil combustion sources, which include ship engines.

Source apportionment of PAHs and n-alkanes bound to PM1 collected near the Venice highway.

Science.gov (United States)

Valotto, Gabrio; Rampazzo, Giancarlo; Gonella, Francesco; Formenton, Gianni; Ficotto, Silvia; Giraldo, Giorgia

2017-04-01

n-Alkanes and polycyclic aromatic hydrocarbons (PAHs) bound to atmospheric particulate matter (PM 1 ) were investigated in a traffic site located in an urban area of Venice Province (Eastern Po Valley, Italy) during the cold season. Considering the critical situation affecting the Veneto Region concerning the atmospheric pollution and the general lack of information on PM 1 composition and emission in this area, this experimental study aims at determining the source profile, their relative contributions and the dispersion of finer particles. Four sources were identified and quantified using the Positive Matrix Factorization receptor model: (1) mixed combustions related to the residential activities, (2) agricultural biomass burning in addition to the resuspension of anthropogenic and natural debris carried by the wind, (3) gasoline and (4) diesel traffic-related combustions. The role of local atmospheric circulation was also investigated to identify the pollutant sources. Copyright © 2016. Published by Elsevier B.V.

Sources of atmospheric aerosols controlling PM10 levels in Heraklion, Crete during winter time

Science.gov (United States)

Kalivitis, Nikolaos; Kouvarakis, Giorgos; Stavroulas, Iasonas; Kandilogiannaki, Maria; Vavadaki, Katerina; Mihalopoulos, Nikolaos

2016-04-01

High concentrations of Particulate Matter (PM) in the atmosphere have negative impact to human health. Thresholds for ambient concentrations that are defined by the directive 2008/50/EC are frequently exceeded even at background conditions in the Mediterranean region as shown in earlier studies. The sources of atmospheric particles in the urban environment of a medium size city of eastern Mediterranean are studied in the present work in order to better understand the causes and characteristics of exceedances of the daily mean PM10limit value of 50 μg m-3. Measurements were performed at the atmospheric quality measurement station of the Region of Crete, at the Heraklion city center on Crete island, during the winter/spring period of 2014-2015 and 2015-2016. Special emphasis was given to the study of the contribution of Black Carbon (BC) to the levels of PM10. Continuous measurements were performed using a beta-attenuation PM10monitor and a 7-wavelength Aethalometer with a time resolution of 30 and 5 minutes respectively. For direct comparison to background regional conditions, concurrent routine measurements at the atmospheric research station of University of Crete at Finokalia were used as background reference. Analysis of exceedances in the daily PM10 mass concentration showed that the total of the exceedances was related to long range transport of Saharan dust rather than local sources. However, compared to the Finokalia station it was found that there were 20% more exceedances in Heraklion, the addition of transported dust on the local pollution was the reason for the additional exceedance days. Excluding dust events, it was found that the PM10variability was dependent on the BC abundance, traffic during rush hours in the morning and biomass burning for domestic heating in the evening contributed significantly to PM10levels in Heraklion.

Long-term particulate matter modeling for health effect studies in California - Part 2: Concentrations and sources of ultrafine organic aerosols

Science.gov (United States)

Hu, Jianlin; Jathar, Shantanu; Zhang, Hongliang; Ying, Qi; Chen, Shu-Hua; Cappa, Christopher D.; Kleeman, Michael J.

2017-04-01

Organic aerosol (OA) is a major constituent of ultrafine particulate matter (PM0. 1). Recent epidemiological studies have identified associations between PM0. 1 OA and premature mortality and low birth weight. In this study, the source-oriented UCD/CIT model was used to simulate the concentrations and sources of primary organic aerosols (POA) and secondary organic aerosols (SOA) in PM0. 1 in California for a 9-year (2000-2008) modeling period with 4 km horizontal resolution to provide more insights about PM0. 1 OA for health effect studies. As a related quality control, predicted monthly average concentrations of fine particulate matter (PM2. 5) total organic carbon at six major urban sites had mean fractional bias of -0.31 to 0.19 and mean fractional errors of 0.4 to 0.59. The predicted ratio of PM2. 5 SOA / OA was lower than estimates derived from chemical mass balance (CMB) calculations by a factor of 2-3, which suggests the potential effects of processes such as POA volatility, additional SOA formation mechanism, and missing sources. OA in PM0. 1, the focus size fraction of this study, is dominated by POA. Wood smoke is found to be the single biggest source of PM0. 1 OA in winter in California, while meat cooking, mobile emissions (gasoline and diesel engines), and other anthropogenic sources (mainly solvent usage and waste disposal) are the most important sources in summer. Biogenic emissions are predicted to be the largest PM0. 1 SOA source, followed by mobile sources and other anthropogenic sources, but these rankings are sensitive to the SOA model used in the calculation. Air pollution control programs aiming to reduce the PM0. 1 OA concentrations should consider controlling solvent usage, waste disposal, and mobile emissions in California, but these findings should be revisited after the latest science is incorporated into the SOA exposure calculations. The spatial distributions of SOA associated with different sources are not sensitive to the choice of

Source Apportionment of PM10 by Positive Matrix Factorization in Urban Area of Mumbai, India

Directory of Open Access Journals (Sweden)

Indrani Gupta

2012-01-01

Full Text Available Particulate Matter (PM10 has been one of the main air pollutants exceeding the ambient standards in most of the major cities in India. During last few years, receptor models such as Chemical Mass Balance, Positive Matrix Factorization (PMF, PCA–APCS and UNMIX have been used to provide solutions to the source identification and contributions which are accepted for developing effective and efficient air quality management plans. Each site poses different complexities while resolving PM10 contributions. This paper reports the variability of four sites within Mumbai city using PMF. Industrial area of Mahul showed sources such as residual oil combustion and paved road dust (27%, traffic (20%, coal fired boiler (17%, nitrate (15%. Residential area of Khar showed sources such as residual oil combustion and construction (25%, motor vehicles (23%, marine aerosol and nitrate (19%, paved road dust (18% compared to construction and natural dust (27%, motor vehicles and smelting work (25%, nitrate (16% and biomass burning and paved road dust (15% in Dharavi, a low income slum residential area. The major contributors of PM10 at Colaba were marine aerosol, wood burning and ammonium sulphate (24%, motor vehicles and smelting work (22%, Natural soil (19%, nitrate and oil burning (18%.

Source profiles of particulate matter emissions from a pilot-scale boiler burning North American coal blends.

Science.gov (United States)

Lee, S W

2001-11-01

Recent awareness of suspected adverse health effects from ambient particulate matter (PM) emission has prompted publication of new standards for fine PM with aerodynamic diameter less than 2.5 microm (PM2.5). However, scientific data on fine PM emissions from various point sources and their characteristics are very limited. Source apportionment methods are applied to identify contributions of individual regional sources to tropospheric particulate concentrations. The existing industrial database developed using traditional source measurement techniques provides total emission rates only, with no details on chemical nature or size characteristics of particulates. This database is inadequate, in current form, to address source-receptor relationships. A source dilution system was developed for sampling and characterization of total PM, PM2.5, and PM10 (i.e., PM with aerodynamic diameter less than 10 pm) from residual oil and coal combustion. This new system has automatic control capabilities for key parameters, such as relative humidity (RH), temperature, and sample dilution. During optimization of the prototype equipment, three North American coal blends were burned using a 0.7-megawatt thermal (MWt) pulverized coal-fired, pilot-scale boiler. Characteristic emission profiles, including PM2.5 and total PM soluble acids, and elemental and carbon concentrations for three coal blends are presented. Preliminary results indicate that volatile trace elements such as Pb, Zn, Ti, and Se are preferentially enriched in PM2.5. PM2.5 is also more concentrated in soluble sulfates relative to total PM. Coal fly ash collected at the outlet of the electrostatic precipitator (ESP) contains about 85-90% PM10 and 30-50% PM2.5. Particles contain the highest elemental concentrations of Si and Al while Ca, Fe, Na, Ba, and K also exist as major elements. Approximately 4-12% of the materials exists as soluble sulfates in fly ash generated by coal blends containing 0.2-0.8% sulfur by mass

Health effects of ambient levels of respirable particulate matter (PM) on healthy, young-adult population

Science.gov (United States)

Shaughnessy, William J.; Venigalla, Mohan M.; Trump, David

2015-12-01

There is an absence of studies that define the relationship between ambient particulate matter (PM) levels and adverse health outcomes among the young and healthy adult sub-group. In this research, the relationship between exposures to ambient levels of PM in the 10 micron (PM10) and 2.5 micron (PM2.5) size fractions and health outcomes in members of the healthy, young-adult subgroup who are 18-39 years of age was examined. Active duty military personnel populations at three strategically selected military bases in the United States were used as a surrogate to the control group. Health outcome data, which consists of the number of diagnoses for each of nine International Classification of Diseases, 9th Revision (ICD-9) categories related to respiratory illness, were derived from outpatient visits at each of the three military bases. Data on ambient concentrations of particulate matter, specifically PM10 and PM2.5, were obtained for these sites. The health outcome data were correlated and regressed with the PM10 and PM2.5 data, and other air quality and weather-related data on a daily and weekly basis for the period 1998 to 2004. Results indicate that at Fort Bliss, which is a US Environmental Protection Agency designated non-attainment area for PM10, a statistically significant association exists between the weekly-averaged number of adverse health effects in the young and healthy adult population and the corresponding weekly-average ambient PM10 concentration. A least squares regression analysis was performed on the Fort Bliss data sets indicated that the health outcome data is related to several environmental parameters in addition to PM10. Overall, the analysis estimates a .6% increase in the weekly rate of emergency room visits for upper respiratory infections for every 10 μg/m3 increase in the weekly-averaged PM10 concentration above the mean. The findings support the development of policy and guidance opportunities that can be developed to mitigate exposures

Size, Composition, and Sources of Health Relevant Particulate Matter in the San Joaquin Valley

Science.gov (United States)

Ham, Walter Allan

Particulate Matter (PM) is an environment contaminant that has been associated with adverse health effects in epidemiological and toxicological studies. Atmospheric PM is made up of a diverse array of chemical species that are emitted from multiple sources across a range of aerodynamic diameters spanning several orders of magnitude. The focus of the present work was the characterization of ambient PM with aerodynamic diameters below 1.8 mum (PM1.8) in 6 size sub-fractions including PM0.1. Chemical species measured included organic carbon, elemental carbon, water soluble ions, trace metals, and organic molecular markers in urban and rural environments in the San Joaquin Valley. These measurements were used to determine differences in relative diurnal size distributions during a severe winter stagnation event, seasonal changes in PM size and composition, and the source origin of carbonaceous PM. This size-resolved information was used to calculate lung deposition patterns of health relevant PM species to evaluate seasonal differences in PM dose. By accurately calculating PM dose, researchers are able to more directly link ambient PM characterization data with biological endpoints. All of these results are used to support ongoing toxicological health effects studies. These types of analyses are important as this type of information may assist regulators with developing control strategies to reduce health effects caused by particulate air pollution.

Source contributions to PM2.5 and PM10 at an urban background and a street location

NARCIS (Netherlands)

Keuken, M. P.; Moerman, M.; Voogt, M.; Blom, M.; Weijers, E. P.; Rockmann, T.; Dusek, U.

The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The C-14 content in EC

Source contributions to PM2.5 and PM10 at an urban background and a street location

NARCIS (Netherlands)

Keuken, M.P.; Moerman, M.M.; Voogt, M.H.

2013-01-01

The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The 14C content in EC

Reduction of PM emissions from specific sources reflected on key components concentrations of ambient PM10

Science.gov (United States)

Minguillon, M. C.; Querol, X.; Monfort, E.; Alastuey, A.; Escrig, A.; Celades, I.; Miro, J. V.

2009-04-01

The relationship between specific particulate emission control and ambient levels of some PM10 components (Zn, As, Pb, Cs, Tl) was evaluated. To this end, the industrial area of Castellón (Eastern Spain) was selected, where around 40% of the EU glazed ceramic tiles and a high proportion of EU ceramic frits (middle product for the manufacture of ceramic glaze) are produced. The PM10 emissions from the ceramic processes were calculated over the period 2000 to 2007 taking into account the degree of implementation of corrective measures throughout the study period. Abatement systems (mainly bag filters) were implemented in the majority of the fusion kilns for frit manufacture in the area as a result of the application of the Directive 1996/61/CE, leading to a marked decrease in PM10 emissions. On the other hand, ambient PM10 sampling was carried out from April 2002 to July 2008 at three urban sites and one suburban site of the area and a complete chemical analysis was made for about 35 % of the collected samples, by means of different techniques (ICP-AES, ICP-MS, Ion Chromatography, selective electrode and elemental analyser). The series of chemical composition of PM10 allowed us to apply a source contribution model (Principal Component Analysis), followed by a multilinear regression analysis, so that PM10 sources were identified and their contribution to bulk ambient PM10 was quantified on a daily basis, as well as the contribution to bulk ambient concentrations of the identified key components (Zn, As, Pb, Cs, Tl). The contribution of the sources identified as the manufacture and use of ceramic glaze components, including the manufacture of ceramic frits, accounted for more than 65, 75, 58, 53, and 53% of ambient Zn, As, Pb, Cs and Tl levels, respectively (with the exception of Tl contribution at one of the sites). The important emission reductions of these sources during the study period had an impact on ambient key components levels, such that there was a high

Elemental characterization of New Year's Day PM10 and PM2.2 particulates matter at several sites in Metro Manila

Energy Technology Data Exchange (ETDEWEB)

Santos, Flora L; Pabroa, Preciosa Corazon B; Morco, Ryan P; Racho, Joseph Michael D [Analytical Measurements Research Group, Philippine Nuclear Research Institute, Commonwealth Ave., Diliman, Quezon City (Philippines)

2007-07-01

In the Philippines, it has been a yearly tradition to welcome the coming of the New Year with the loudest noise as can be achieved. Firecrackers and fireworks have been a necessity for Filipinos during this time despite bans on the use of most of these and despite the Department of Health (DOH) campaign to use alternative safe practices to welcome the New Year. Data for PM 10 samples (fractionated as PM 10-2.2 or the course fraction and PM2.2 or the fine fraction) collected in four PNRI sampling sites in Metro Manila show the air pollution impacts of fireworks on New Year's Eve. Samples were collected from 1998 to 2006 using a Gent dichotomous sampler in connection with the PNRI project {sup P}articulate Matter Source Apportionment Using Nuclear and Related Analytical Techniques{sup .} Particulate mass was determined by gravimetry. Elemental analysis of the air filters was done using X-ray Fluorescence Spectrometry (X RF) or Particle induced X-ray Emission (PIXE), multielemental non-destructive nuclear analytical techniques. Black carbon was analyzed using reflectometry. PM 10 values increased by two to four times the usual averages (36.4 to 55.4 ug/cum) and in 2002 even exceeded the PNAAQ short-term guideline value of 150 ug/cum at the ADMU sampling station. PM2.2 values increased by two to six times the usual averages (15 to 28 ug/cum), even many times exceeding US EPA short-term guideline value of 65 ug/cum. The increase in the particulate mass of New Year's Day samples can be attributed more to an increase in the metal pollutants rather than the black carbon, with higher contribution to the fine fraction. Increase in the elemental concentrations of Al, S, Cl, K, Ba, Sr, Ti, V, Mn, Cu and Pb were observed with the highest contribution from K. Results show that the usual practices of burning firecrackers and fireworks during New Year's day celebration is a very strong source of air pollution which contributes significantly high amount of metal pollutants in the

Oxidative potential of ambient PM2.5 in the coastal cities of the Bohai Sea, northern China: Seasonal variation and source apportionment.

Science.gov (United States)

Liu, WeiJian; Xu, YunSong; Liu, WenXin; Liu, QingYang; Yu, ShuangYu; Liu, Yang; Wang, Xin; Tao, Shu

2018-05-01

Emissions of air pollutants from primary and secondary sources in China are considerably higher than those in developed countries, and exposure to air pollution is main risk of public health. Identifying specific particulate matter (PM) compositions and sources are essential for policy makers to propose effective control measures for pollutant emissions. Ambient PM 2.5 samples covered a whole year were collected from three coastal cities of the Bohai Sea. Oxidative potential (OP) was selected as the indicator to characterize associated PM compositions and sources most responsible for adverse impacts on human health. Positive matrix factorization (PMF) and multiple linear regression (MLR) were employed to estimate correlations of PM 2.5 sources with OP. The volume- and mass-based dithiothreitol (DTT v and DTT m ) activities of PM 2.5 were significantly higher in local winter or autumn (p  0.700, p water-soluble organic carbon (WSOC) and some transition metals. Using PMF, source fractions of PM 2.5 were resolved as secondary source, traffic source, biomass burning, sea spray and urban dust, industry, coal combustion, and mineral dust. Further quantified by MLR, coal combustion, biomass burning, secondary sources, industry, and traffic source were dominant contributors to the water-soluble DTT v activity. Our results also suggested large differences in seasonal contributions of different sources to DTT v variability. A higher contribution of DTT v was derived from coal combustion during the local heating period. Secondary sources exhibited a greater fraction of DTT v in summer, when there was stronger solar radiation. Traffic sources exhibited a prevailing contribution in summer, and industry contributed larger proportions in spring and winter. Future abatement priority of air pollution should reduce the sources contributing to OP of PM 2.5 . Copyright © 2018 Elsevier Ltd. All rights reserved.

Temporal variations of fine and coarse particulate matter sources in Jeddah, Saudi Arabia.

Science.gov (United States)

Lim, Chris C; Thurston, George D; Shamy, Magdy; Alghamdi, Mansour; Khoder, Mamdouh; Mohorjy, Abdullah M; Alkhalaf, Abdulrahman K; Brocato, Jason; Chen, Lung Chi; Costa, Max

2018-02-01

This study provides the first comprehensive analysis of the seasonal variations and weekday/weekend differences in fine (aerodynamic diameter Saudi Arabia. Air quality samples were collected over 1 yr, from June 2011 to May 2012 at a frequency of three times per week, and analyzed. The average mass concentrations of PM 2.5 (21.9 μg/m 3 ) and PM 10 (107.8 μg/m 3 ) during the sampling period exceeded the recommended annual average levels by the World Health Organization (WHO) for PM 2.5 (10 μg/m 3 ) and PM 10 (20 μg/m 3 ), respectively. Similar to other Middle Eastern locales, PM 2.5-10 is the prevailing mass component of atmospheric particulate matter at Jeddah, accounting for approximately 80% of the PM 10 mass. Considerations of enrichment factors, absolute principal component analysis (APCA), concentration roses, and backward trajectories identified the following source categories for both PM 2.5 and PM 2.5-10 : (1) soil/road dust, (2) incineration, and (3) traffic; and for PM 2.5 only, (4) residual oil burning. Soil/road dust accounted for a major portion of both the PM 2.5 (27%) and PM 2.5-10 (77%) mass, and the largest source contributor for PM 2.5 was from residual oil burning (63%). Temporal variations of PM 2.5-10 and PM 2.5 were observed, with the elevated concentration levels observed for mass during the spring (due to increased dust storm frequency) and on weekdays (due to increased traffic). The predominant role of windblown soil and road dust in both the PM 2.5 and PM 2.5-10 masses in this city may have implications regarding the toxicity of these particles versus those in the Western world where most PM health assessments have been made in the past. These results support the need for region-specific epidemiological investigations to be conducted and considered in future PM standard setting. Temporal variations of fine and coarse PM mass, elemental constituents, and sources were examined in Jeddah, Saudi Arabia, for the first time. The main source

Ambient PM2.5 Exposure in India: Burden, Source-Apportionment and Projection Under Climate Change

Science.gov (United States)

Dey, S.; Chowdhury, S.; Upadhyay, A. K.; Smith, K. R.

2017-12-01

Air pollution has been identified as one of the leading factors of premature death in India. Absence of adequate in-situ monitors led us to use satellite retrieved aerosol optical depth (AOD) data to infer surface fine particulate matter (PM2.5). Annual premature mortality burden due to ambient PM2.5 exposure is estimated to be 1.17 (0.42-2.7) million for India. A chemical transport model WRF-Chem is utilized to estimate source-apportioned PM2.5 exposure. We estimate the exposure for four major sources - transport, residential, energy and industrial and found that the largest contribution to ambient PM2.5 exposure in India is contributed by residential sources. We estimate that if all the solid fuel use at households is replaced by clean fuel, ambient PM2.5 exposure would reduce by 30-45%, leading to 170,000 (14.5% of total burden) averted premature deaths annually. To understand how the air quality is projected to change under climate change scenarios, we analyze 13 CMIP5 models. We calculate the relative changes in PM2.5 (ensemble mean) in future relative to the baseline period (2001-2005) and apply the factor to satellite-derived PM2.5 exposure in baseline period to project future PM2.5 exposure. Ambient PM2.5 is expected to reach a maxima in 2030 under RCP4.5 (15.5% rise from baseline period) and in 2040 (25.5% rise) under RCP8.5 scenario. The projected exposure under RCP4.5 and RCP8.5 scenarios are further used to estimate premature mortality burden till the end of the century by considering population distribution projections from five shared socio-economic pathways (SSP) scenarios. We separate the burden due to ambient PM2.5 exposure in future attributable to change in meteorology due to climate change and change in demographic and epidemiological transitions. If all-India average PM2.5 exposure meets WHO interim target 1 (35 µg/m3) by 2031-40, 28000-38000 and 41100-60100 premature deaths can be averted every year under RCP4.5 and RCP8.5 respectively. Even

High-resolution sampling and analysis of ambient particulate matter in the Pearl River Delta region of southern China: source apportionment and health risk implications

Science.gov (United States)

Zhou, Shengzhen; Davy, Perry K.; Huang, Minjuan; Duan, Jingbo; Wang, Xuemei; Fan, Qi; Chang, Ming; Liu, Yiming; Chen, Weihua; Xie, Shanju; Ancelet, Travis; Trompetter, William J.

2018-02-01

Hazardous air pollutants, such as trace elements in particulate matter (PM), are known or highly suspected to cause detrimental effects on human health. To understand the sources and associated risks of PM to human health, hourly time-integrated major trace elements in size-segregated coarse (PM2.5-10) and fine (PM2.5) particulate matter were collected at the industrial city of Foshan in the Pearl River Delta region, China. Receptor modeling of the data set by positive matrix factorization (PMF) was used to identify six sources contributing to PM2.5 and PM10 concentrations at the site. Dominant sources included industrial coal combustion, secondary inorganic aerosol, motor vehicles and construction dust along with two intermittent sources (biomass combustion and marine aerosol). The biomass combustion source was found to be a significant contributor to peak PM2.5 episodes along with motor vehicles and industrial coal combustion. Conditional probability function (CPF) analysis was applied to estimate the source locations using the PMF-resolved source contribution coupled with the surface wind direction data. Health exposure risk of hazardous trace elements (Pb, As, Si, Cr, Mn and Ni) and source-specific values were estimated. The total hazard quotient (HQ) of PM2.5 was 2.09, higher than the acceptable limit (HQ = 1). The total carcinogenic risk (CR) was 3.37 × 10-3 for PM2.5, which was 3 times higher than the least stringent limit (1.0 × 10-4). Among the selected trace elements, As and Pb posed the highest non-carcinogenic and carcinogenic risks to human health, respectively. In addition, our results show that the industrial coal combustion source is the dominant non-carcinogenic and carcinogenic risk contributor, highlighting the need for stringent control of this source. This study provides new insight for policy makers to prioritize sources in air quality management and health risk reduction.

Elemental composition of PM 10 and PM 2.5 in urban environment in South Brazil

Science.gov (United States)

Braga, C. F.; Teixeira, E. C.; Meira, L.; Wiegand, F.; Yoneama, M. L.; Dias, J. F.

The purpose of the present study is to analyze the elemental composition and the concentrations of PM 10 and PM 2.5 in the Guaíba Hydrographic Basin with HV PM 10 and dichotomous samplers. Three sampling sites were selected: 8° Distrito, CEASA and Charqueadas. The sampling was conducted from October 2001 to December 2002. The mass concentrations of the samplers were evaluated, while the elemental concentrations of Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn were determined using the Particle-Induced X-ray Emission (PIXE) technique. Factor Analysis and Canonical Correlation Analysis were applied to the chemical and meteorological variables in order to identify the sources of particulate matter. Industrial activities such as steel plants, coal-fired power plants, hospital waste burning, vehicular emissions and soil were identified as the sources of the particulate matter. Concentration levels higher than the daily and the annual average air quality standards (150 and 50 μg m -3, respectively) set by the Brazilian legislation were not observed.

Cause-specific stillbirth and exposure to chemical constituents and sources of fine particulate matter.

Science.gov (United States)

Ebisu, Keita; Malig, Brian; Hasheminassab, Sina; Sioutas, Constantinos; Basu, Rupa

2018-01-01

The stillbirth rate in the United States is relatively high, but limited evidence is available linking stillbirth with fine particulate matter (PM 2.5 ), its chemical constituents and sources. In this study, we explored associations between cause-specific stillbirth and prenatal exposures to those pollutants with using live birth and stillbirth records from eight California locations during 2002-2009. ICD-10 codes were used to identify cause of stillbirth from stillbirth records. PM 2.5 total mass and chemical constituents were collected from ambient monitors and PM 2.5 sources were quantified using Positive Matrix Factorization. Conditional logistic regression was applied using a nested case-control study design (N = 32,262). We found that different causes of stillbirth were associated with different PM 2.5 sources and/or chemical constituents. For stillbirths due to fetal growth, the odds ratio (OR) per interquartile range increase in gestational age-adjusted exposure to PM 2.5 total mass was 1.23 (95% confidence interval (CI): 1.06, 1.44). Similar associations were found with resuspended soil (OR=1.25, 95% CI: 1.10, 1.42), and secondary ammonium sulfate (OR=1.45, 95% CI: 1.18, 1.78). No associations were found between any pollutants and stillbirths caused by maternal complications. This study highlighted the importance of investigating cause-specific stillbirth and the differential toxicity levels of specific PM 2.5 sources and chemical constituents. Copyright © 2017 Elsevier Inc. All rights reserved.

AIRUSE-LIFE+: a harmonized PM speciation and source apportionment in five southern European cities

Directory of Open Access Journals (Sweden)

F. Amato

2016-03-01

Full Text Available The AIRUSE-LIFE+ project aims at characterizing similarities and heterogeneities in particulate matter (PM sources and contributions in urban areas from southern Europe. Once the main PMx sources are identified, AIRUSE aims at developing and testing the efficiency of specific and non-specific measures to improve urban air quality. This article reports the results of the source apportionment of PM10 and PM2.5 conducted at three urban background sites (Barcelona, Florence and Milan, BCN-UB, FI-UB and MLN-UB, one suburban background site (Athens, ATH-SUB and one traffic site (Porto, POR-TR. After collecting 1047 PM10 and 1116 PM2.5 24 h samples during 12 months (from January 2013 on simultaneously at the five cities, these were analysed for the contents of OC, EC, anions, cations, major and trace elements and levoglucosan. The USEPA PMF5 receptor model was applied to these data sets in a harmonized way for each city. The sum of vehicle exhaust (VEX and non-exhaust (NEX contributes between 3.9 and 10.8 µg m−3 (16–32 % to PM10 and 2.3 and 9.4 µg m−3 (15–36 % to PM2.5, although a fraction of secondary nitrate is also traffic-related but could not be estimated. Important contributions arise from secondary particles (nitrate, sulfate and organics in PM2.5 (37–82 % but also in PM10 (40–71 %, mostly at background sites, revealing the importance of abating gaseous precursors in designing air quality plans. Biomass burning (BB contributions vary widely, from 14–24 % of PM10 in POR-TR, MLN-UB and FI-UB, 7 % in ATH-SUB, to  <  2 % in BCN-UB. In PM2.5, BB is the second most important source in MLN-UB (21 % and in POR-TR (18 %, the third one in FI-UB (21 % and ATH-SUB (11 %, but is again negligible (< 2 % in BCN-UB. This large variability among cities is mostly due to the degree of penetration of biomass for residential heating. In Barcelona natural gas is very well supplied across the city and is used as fuel in 96 % of

Elemental Quantification and Source Identification of Airborne Particulate Matter in Pathumwan District

International Nuclear Information System (INIS)

Chueinta, Wanna; Bunprapob, Suphamattree

2003-10-01

Airborne particulate matter (APM) is apparently the biggest air pollution problem found in capital and other big cities. APM has the adverse impact on human health and also on the environment. PM 10 (particle with aerodynamic diameter le ss than 10 μm), in particularly, can cause the respiratory diseases since it can penetrate the respiratory system. Furthermore, PM 25 (particle with aerodynamic diameter less than 2.5 μm) is the major cause of visibility impairment. This paper reports the study of urban air pollution at Pathumwan District, a business area in Bangkok City center. Coarse and fine fractions of PM 10 (P M-2 .2 - 10 and PM 2.2 , respectively) were collected by a Gent stacked filter unit air sampler during January-December 2002. The filter samples were measured for mass and black carbon. Elemental concentrations were analyzed by instrumental neutron activation analysis. The results indicate the rather high level of PM 10 at the sampling site. The annual average of PM 10 is 56.6 μg/m 3 compared to the ambient air quality standard of 50 μg/m 3 . The obtained data of black carbon and elemental concentrations were used for investigation of pollution sources by applying a receptor model called Positive Matrix Factorization. It could identify that the main sources were most likely city dust, emissions from vehicle combustion, incineration and sea-salt

Levels, Composition and Sources of PM in the Mexico City Metropolitan Area During the MILAGRO Campaign

Science.gov (United States)

Querol, X.; Pey, J.; Minguillon, M. C.; Perez, N.; Alastuey, A.; Moreno, T.; Bernabe, R.; Blanco, S.; Cardenas, B.

2007-05-01

Particle air pollution in urban agglomerations comes mostly from anthropogenic sources, mainly traffic, industrial processes, energy production, domestic and residential emissions, construction, but also a minor contribution from natural sources may be expected (bioaerosols, soil dust, marine aerosol). Once emitted into the atmosphere, this complex mixture of pollutants may be transformed as a function of the ambient conditions and the interaction among the different PM components, and also between PM components and gaseous pollutants. This system is especially complex in mega-cities due to the large emission volumes of PM components and gaseous precursors, the high variability and broad distribution of emission sources, and the possible long range transport of the polluted air masses. Speciation studies help to identify major sources of PM components with the end objective of applying plans and programs for PM pollution abatement. In this framework, concentration levels and compositions of particulate matter (PM2.5, PM10 and TSP) have been measured simultaneously at two sites in the Mexico City Metropolitan Area (T0 and CENICA) and at one site 50 km away from Mexico City (T1) during the MILAGRO campaign (1st to 31st March 2006). Spatial and time (day and night) variations have been analysed. Coarse fraction levels were higher at T1 than at CENICA and T0, contrary to what was expected. This was due to the important soil re-suspension at T1, contributing significantly to the crustal load. Moreover, crustal levels were higher during daytime than during nights at all sites, while some secondary compounds (sulphate and ammonium) presented an opposite trend. Regarding trace elements, levels of Pb, Zn and Cd were higher at T0 than at CENICA and T1, probably due to traffic contribution. Arsenic levels did not show a clear pattern, being alternatively higher at CENICA and T0. Two intense episodes of Hg particulate have been recorded, more noticeable at T1 than at the urban

Source contributions to PM2.5 and PM10 at an urban background and a street location

Science.gov (United States)

Keuken, M. P.; Moerman, M.; Voogt, M.; Blom, M.; Weijers, E. P.; Röckmann, T.; Dusek, U.

2013-06-01

The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The 14C content in EC and OC concentrations was also determined, to distinguish the contribution from "modern" carbon (e.g., biogenic emissions, biomass burning and wildfires) and fossil fuel combustion. It was concluded that the urban background of PM2.5 and PM10 is dominated by the regional background, and that primary and secondary PM emission by urban sources contribute less than 15%. The 14C analysis revealed that 70% of OC originates from modern carbon and 30% from fossil fuel combustion. The corresponding percentages for EC are, respectively 17% and 83%. It is concluded that in particular the urban population living in street canyons with intense road traffic has potential health risks. This is due to exposure to elevated concentrations of a factor two for EC from exhaust emissions in PM2.5 and a factor 2-3 for heavy metals from brake and tyre wear, and re-suspended road dust in PM10. It follows that local air quality management may focus on local measures to street canyons with intense road traffic.

Source identification of particulate matter in a semi-urban area of Malaysia using multivariate techniques.

Science.gov (United States)

Wahid, N B A; Latif, M T; Suan, L S; Dominick, D; Sahani, M; Jaafar, S A; Mohd Tahir, N

2014-03-01

This study aims to determine the composition and sources of particulate matter with an aerodynamic diameter of 10 μm or less (PM10) in a semi-urban area. PM10 samples were collected using a high volume sampler. Heavy metals (Fe, Zn, Pb, Mn, Cu, Cd and Ni) and cations (Na(+), K(+), Ca(2+) and Mg(2+)) were detected using inductively coupled plasma mass spectrometry, while anions (SO4 (2-), NO3 (-), Cl(-) and F(-)) were analysed using Ion Chromatography. Principle component analysis and multiple linear regressions were used to identify the source apportionment of PM10. Results showed the average concentration of PM10 was 29.5 ± 5.1 μg/m(3). The heavy metals found were dominated by Fe, followed by Zn, Pb, Cu, Mn, Cd and Ni. Na(+) was the dominant cation, followed by Ca(2+), K(+) and Mg(2+), whereas SO4 (2-) was the dominant anion, followed by NO3 (-), Cl(-) and F(-). The main sources of PM10 were the Earth's crust/road dust, followed by vehicle emissions, industrial emissions/road activity, and construction/biomass burning.

Particulate pollution of PM10 and PM2.5 due to strong anthropopressure in Sosnowiec city

Directory of Open Access Journals (Sweden)

Jolanta Cembrzyńska

2012-12-01

Full Text Available Introduction: Air contamination with particulate matter causes a serious problem in large cities and urban-industrial agglomerations both in Poland and Europe. Anthropogenic sources of air pollution in urban areas are emissions from municipal, industrial and transportation sector. Many epidemiological studies have revealed that exposure to air pollution, especially the fine particles with aerodynamic diameter less than 2,5 micrometer, can pose a threat to human health exposed to exceedingly high concentrations of particulate matter. Aim of the study: The aim of this study was to evaluate PM10 and PM2,5 mass concentrations in autumn and winter season in the city of Sosnowiec, in relation to ambient air quality standards in Poland and the European Union. Results: The average concentrations of PM10 and PM2,5 in autumn-winter seasons in Sosnowiec city 2010–2011 were 2,1 to 2,7 times higher than limit values, specified in the legislation acts.

Seasonal variation of the metal composition in particulate matter (PM) in Graz determined with ICPMS

International Nuclear Information System (INIS)

Hartl, M.; Raber, G.; Goessler, W.; Licbinsky, R.; Pongratz, T.

2009-01-01

Full text: Graz, the 2 nd biggest city of Austria, is not only famous for its cultural heritage but is also well known as one of the most heavily air-polluted cities of Austria. Samples of particulate matter (PM 1.0 , PM 2.5 , and PM 10 ), collected in Graz over a one year period, were analyzed for 36 metals by ICPMS following microwave-assisted acid digestion. Accumulation of PM in the city (Graz is located in a basin) and additional emissions (e.g. domestic combustion) during winter caused not only higher PM concentrations but also marked changes in the PM metal composition. (author)

Characterization of carbonaceous materials in PM2.5 and PM10 size fractions in Morogoro, Tanzania, during 2006 wet season campaign

International Nuclear Information System (INIS)

Mkoma, Stelyus L.; Chi Xuguang; Maenhaut, Willy

2010-01-01

Atmospheric aerosol samples in PM10 and PM2.5 size fractions were collected in parallel at a rural site in Morogoro during wet season in March and April 2006. All samples were analysed for the particulate matter mass, for organic, elemental, and total carbon (OC, EC, and TC), and for water-soluble OC (WSOC). The average PM10 and PM2.5 mass concentrations and associated standard deviations were 14 ± 13 μg/m 3 and 7.3 ± 4 μg/m 3 respectively. On average, TC accounted for 33% of the PM10 mass and 44% of the PM2.5 mass for the campaign. The average OC/PM percentage ratios were 27% and 33% in PM10 and PM2.5 size fractions respectively and a larger fraction of the OC was water-soluble. The observed low EC/TC mean percentage ratios of 10-14% respectively for PM10 and PM2.5 fractions indicate that the carbonaceous aerosol originates mainly from biogenic aerosols and/or biomass burning. A simple source apportionment approach was used to apportion the OC to biofuel and charcoal burning. On average, 93% of the PM10 OC was attributed to biofuel and 7% to charcoal burning in the 2006 wet season campaign. However, it is suggested that a contribution to the OC at Morogoro could also come from other natural biogenic matter, and/or biomass burning aerosols. The results for the sources of OC at Morogoro should therefore be considered with great caution.

Bioaccessibility and Speciation of Potential Toxicants in Some Geogenic Sources of Atmospheric Particulate Matter

Science.gov (United States)

Morman, S. A.; Wolf, R. E.; Plumlee, G.; Reynolds, R. L.

2008-12-01

The correlation of exposure to particulate matter (PM) and increased morbidity and mortality was established in the 1970's. Research focused on elucidating mechanisms of action (i.e. particle size, composition, and biodurability), has generally examined anthropogenic sources such as solid or liquid combustion byproducts of fossil fuels, byproducts from the smelting of metal ores, and commercial/industrial mineral dusts (asbestos, crystalline silica. metal dusts). While many studies exist on agricultural exposures to inorganic dust, far fewer have examined health issues related to particulate matter contributions from rural, non-agricultural dusts or other geogenic sources. Geogenic PM (produced by natural processes such as volcanic ash, volcanic fog (vog), dusts from dry lakes or glacial deposits, smoke and windborne ash from wildfires, and dusts containing various soil pathogens) and geoanthropogenic PM (produced from natural sources by processes that are modified or enhanced by human activities such as dusts from lakebeds dried by human removal of water, dusts produced from areas that have undergone desertification as a result of human practices etc.) are increasingly recognized as potential agents of toxicity and disease, via both environmental and occupational exposures. Surface sediment on some dry lake beds may contribute significant amounts of mineral dusts to the atmospheric load. For example, Owens Lake (a dry lake in southern California) has been a major source of PM10 (particulate matter less than 10 micrometers) dust in the United States. Dusts from dry and drying saline lakes may contain high concentrations of metals, such as arsenic, with known human health toxicity. Wildfires, consuming over nine million acres in 2007, also contribute significant amounts of particulate matter in addition to their other hazards. Designed to estimate the bioaccessibility of metals in soils, dusts and other environmental materials by measuring the reactivity of the

Source contributions of fine particulate matter during one winter haze episodes in Xi'an, China

Science.gov (United States)

Yang, X.; Wu, Q.

2017-12-01

Long-term exposure to high levels of fine particulate matter (PM2.5) is found to be associated with adverse effects on human health, ecological environment and climate change. Identification the major source regions of fine particulate matter are essential to proposing proper joint prevention and control strategies for heavy haze mitigation. In this work, the Comprehensive Air Quality Model with extensions (CAMx) together with the Particulate Source Apportionment Technology (PSAT) and the Weather Research and Forecast Model (WRF), have been applied to analyze the major source regions of PM2.5 in Xi'an during the heavy haze episodes in winter (29, December, 2016 - 5 January 2017), and the framework of the model system is shown in Fig. 1. Firstly, according to the model evaluation of the daily PM2.5 concentrations for the two months, the model has well performance, and the fraction of predictions within a factor of 2 of the observations (FAC2) is 84%, while the correlation coefficient (R) is 0.80 in Xi'an. By using the PSAT in CAMx model, a detailed source region contribution matrix is derived for all points within the Xi'an region and its six surrounding areas, and long-range regional transport. The results show that the local emission in Xi'an is the mainly sources at downtown area, which contributing 72.9% as shown in Fig.2, and the contribution rate of transportations between adjacent areas depends on wind direction. Meanwhile, three different suburban areas selected for detailed analysis in fine particles sources. Comparing to downtown area, the sources of suburban areas are more multiply, and the transportations make the contribution 40%-82%. In the suburban areas, regional inflows play an important role in the fine particles concentrations, indicating a strong need for regional joint emission control efforts. The results enhance the quantitative understanding of the PM2.5 source regions and provide a basis for policymaking to advance the control of pollution

Temporal evolution of main ambient PM2. 5 sources in Santiago, Chile, from 1998 to 2012

Science.gov (United States)

Barraza, Francisco; Lambert, Fabrice; Jorquera, Héctor; María Villalobos, Ana; Gallardo, Laura

2017-08-01

The inhabitants of Santiago, Chile have been exposed to harmful levels of air pollutants for decades. The city's poor air quality is a result of steady economic growth, and stable atmospheric conditions adverse to mixing and ventilation that favor the formation of oxidants and secondary aerosols. Identifying and quantifying the sources that contribute to the ambient levels of pollutants is key for designing adequate mitigation measures. Estimating the evolution of source contributions to ambient pollution levels is also paramount to evaluating the effectiveness of pollution reduction measures that have been implemented in recent decades. Here, we quantify the main sources that have contributed to fine particulate matter (PM2. 5) between April 1998 and August 2012 in downtown Santiago by using two different source-receptor models (PMF 5.0 and UNMIX 6.0) that were applied to elemental measurements of 1243 24 h filter samples of ambient PM2.5. PMF resolved six sources that contributed to ambient PM2. 5, with UNMIX producing similar results: motor vehicles (37.3 ± 1.1 %), industrial sources (18.5 ± 1.3 %), copper smelters (14.4 ± 0.8 %), wood burning (12.3 ± 1.0 %), coastal sources (9.5 ± 0.7 %) and urban dust (3.0 ± 1.2 %). Our results show that over the 15 years analyzed here, four of the resolved sources significantly decreased [95 % confidence interval]: motor vehicles 21.3 % [2.6, 36.5], industrial sources 39.3 % [28.6, 48.4], copper smelters 81.5 % [75.5, 85.9], and coastal sources 58.9 % [38.5, 72.5], while wood burning did not significantly change and urban dust increased by 72 % [48.9, 99.9]. These changes are consistent with emission reduction measures, such as improved vehicle emission standards, cleaner smelting technology, introduction of low-sulfur diesel for vehicles and natural gas for industrial processes, public transport improvements, etc. However, it is also apparent that the mitigation expected from the above regulations has been partially

Chemical mass balance source apportionment of PM10 and TSP in residential and industrial sites of an urban region of Kolkata, India.

Science.gov (United States)

Gupta, A K; Karar, Kakoli; Srivastava, Anjali

2007-04-02

Daily average PM(10) (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 microm aerodynamic diameter), TSP (total suspended particulate matter) and their chemical species mass concentrations were measured at residential and industrial sites of an urban region of Kolkata during November 2003-November 2004. Source apportionment using chemical mass balance model revealed that the most dominant source throughout the study period at residential site was coal combustion (42%), while vehicular emission (47%) dominates at industrial site to PM(10). Paved road, field burning and wood combustion contributed 21%, 7% and 1% at residential site, while coal combustion, metal industry and soil dust contributed 34%, 1% and 1% at industrial site, respectively, to PM(10) during the study period. The contributors to TSP included coal combustion (37%), soil dust (19%), road dust (17%) and diesel combustion (15%) at residential site, while soil dust (36%), coal combustion (17%), solid waste (17%), road dust (16%) and tyre wear (7%) at industrial site. Significant seasonal variations of the particulate matters have been observed during the study period. In the monitoring sites total carbon, organic carbon and iron were found to be the marker species of road dust, while organic carbon, total carbon, chloride and sulfate have been observed as the marker species of soil dust in TSP.

A five-year study of particulate matter (PM2.5) and cerebrovascular diseases

International Nuclear Information System (INIS)

Leiva G, Manuel A.; Santibañez, Daniela A.; Ibarra E, Sergio; Matus C, Patricia; Seguel, Rodrigo

2013-01-01

Cerebrovascular accidents, or strokes, are the second leading cause of mortality and the leading cause of morbidity in both Chile and the rest of the world. However, the relationship between particulate matter pollution and strokes is not well characterized. The association between fine particle concentration and stroke admissions was studied. Data on hospital admissions due to cerebrovascular accidents were collected from the Ministry of Health. Air quality and meteorological data were taken from the Air Quality database of the Santiago Metropolitan Area. Santiago reported 33,624 stroke admissions between January 1, 2002 and December 30, 2006. PM2.5 concentration was markedly seasonal, increasing during the winter. This study found an association between PM2.5 exposure and hospital admissions for stroke; for every PM2.5 concentration increase of 10 μg m −3 , the risk of emergency hospital admissions for cerebrovascular causes increased by 1.29% (95% CI 0.552%–2.03%). Highlights: •Particulate matter pollution – cerebrovascular diseases relationship is not well known. •Cerebrovascular diseases are the second leading cause of mortality and the leading cause of morbidity. •PM2.5 increase 10 μg/m 3 the risk of hospital admissions for stroke causes increases by 1.29%. •The results are similar to that of other cities worldwide. -- Relationship between PM pollution and strokes is not well characterized. In Santiago the risk of the stroke increased by 1.29%; for every increase of 10 μg m −3 in PM2.5

Chemical characterization and sources of personal exposure to fine particulate matter in the general population of Guangzhou, China

Science.gov (United States)

Chen, Xiao-Cui; Jahn, Heiko J.; Engling, Guenter; Ward, Tony J.; Kraemer, Alexander; Ho, Kin-Fai; Hung-Lam Yim, Steve; Chan, Chuen-Yu

2017-04-01

Fine particulate matter pollution severely deteriorates the environmental conditions and negatively impacts human health in the Chinese megacity Guangzhou. Concurrent ambient and personal measurements of fine particulate matter (PM2.5) were conducted in Guangzhou, China. Personal-to-ambient (P-C) relationships of PM2.5 chemical components were determined and sources of personal PM2.5 exposure were evaluated using principal component analysis along with a mixed-effects model. Water-soluble inorganic ions (mainly secondary inorganic ions) and anhydrosugars exhibited median personal-to-ambient (P/C) ratios < 1 accompanied by strong P-C correlations, indicating that these constituents in personal PM2.5 were significantly affected by ambient sources. Conversely, elemental carbon (EC) and calcium (Ca2+) showed median P/C ratios greater than unity, which indicated that among subjects who spent a great amount of time indoors, aside from particles of ambient origin, individual's total exposure to PM2.5 includes contributions of non-ambient exposure while indoors and outdoors (e.g., local traffic, indoor sources, personal activities). SO42- displayed very low coefficient of divergence (COD) values coupled with strong P-C correlations, implying a uniform distribution of SO42- in the urban area of Guangzhou. EC, Ca2+, and levoglucosan were otherwise heterogeneously distributed across individuals in different districts. Regional air pollution (50.4 ± 0.9%), traffic-related particles (8.6 ± 0.7%), dust-related particles (5.8 ± 0.7%), and biomass burning emissions (2.0 ± 0.2%) were moderate to high positive sources of personal PM2.5 exposure in Guangzhou. The observed positive and significant contribution of Ca2+ to personal PM2.5 exposure, highlighting indoor sources and/or personal activities, were driving factors determining personal exposure to dust-related particles. Considerable discrepancies (COD values ranging from 0.42 to 0.50) were shown between ambient

Comparison of economic instruments to reduce PM_2_._5 from industrial and residential sources

International Nuclear Information System (INIS)

Mardones, Cristian; Saavedra, Andrés

2016-01-01

In the literature, it is possible to find different studies that compare economic instruments performance applied to the industrial sources regulation; however, evidence about pollution from residential sources is scarce. For this reason, the present study simulates and compares an emission permit system (EPS) and an ambient permit system (APS) when fine particulate matter pollution (PM_2_._5) is generated from industrial and residential sources. Thus, this research contributes to the spatial, economic and environmental assessment of industrial and residential emissions. The options to reduce pollution include replacement of heating devices in residential sources and installing end-of-pipe technologies in industrial sources. The results in terms of total cost and technological chosen options are similar under an APS and EPS for targets lesser to 80%. This is explained because it is more cost-effective to reduce emissions in residential sources than in industrial sources, and additionally, residential pollution has only local impact. However, some industrial sources should install abatement technologies for more demanding targets; in this case as industrial pollution are scattered in different areas, the total cost of an APS are lower than the total cost of an EPS. - Highlights: • The impact of wood burning on air quality can be significant in urban areas. • Residential and industrial sources in regulatory schemes to PM_2_._5 are analyzed. • Wood smoke pollution can be reduced by changing to more efficient heating devices. • Wood heater replacement is more cost-effective than abatement technologies. • The results are similar under APS and EPS for targets lesser to 80%.

High-resolution sampling and analysis of air particulate matter in the Pear River Delta region of Southern China: source apportionment and health risk assessment

Science.gov (United States)

Zhou, S.; Day, P. K.; Wang, X.

2017-12-01

Hazardous air pollutants, such as trace elements in particulate matters (PM), are known or highly suspected to cause detrimental effects on human health. To understand the sources and associated risks of PM to human health, hourly time-integrated major trace elements in size-segregated coarse (PM10-2.5) and fine (PM2.5) particulate matter were collected and examined in an industrial city of Foshan in the Pearl River Delta region, China. Receptor modeling of the dataset by positive matrix factorization (PMF) was used to identify six sources contributing to PM2.5 and PM10 concentrations at the site. Dominant sources included industrial coal combustion, secondary inorganic aerosol, motor vehicles and construction dust along with two intermittent sources, biomass combustion and marine aerosol. The biomass combustion source was found to be a significant contributor to peak PM2.5 episodes along with motor vehicles and industrial coal combustion. Conditional probability function (CPF) was applied to estimate the local source effects from wind direction using the PMF-resolved source contribution coupled with the surface wind direction data. Health exposure risk for hazardous trace elements (Pb, As, Cr, Ni, Zn, V, Cu, Mn, Fe) and source-specific values were estimated. The total hazard quotient (total HQ =HI) of PM2.5 was 2.09, which is two times higher than the acceptable limit (HQ = 1). The total carcinogenic risk was 3.37*10-3 for PM2.5, which was three orders higher than the acceptable limit (i.e. 1.0*10-6). Among the selected trace elements, As and Pb posed the highest non-carcinogenic and carcinogenic risks for human health, respectively. In additional, our results showed that industrial coal combustion source was the dominant non-carcinogenic and carcinogenic risks contributor, highlighting the need for stringent control of this source. This study can provide new insight for policy makers to prioritize sources in air quality management and health risk reduction.

High-resolution sampling and analysis of ambient particulate matter in the Pearl River Delta region of southern China: source apportionment and health risk implications

Directory of Open Access Journals (Sweden)

S. Zhou

2018-02-01

Full Text Available Hazardous air pollutants, such as trace elements in particulate matter (PM, are known or highly suspected to cause detrimental effects on human health. To understand the sources and associated risks of PM to human health, hourly time-integrated major trace elements in size-segregated coarse (PM2.5–10 and fine (PM2.5 particulate matter were collected at the industrial city of Foshan in the Pearl River Delta region, China. Receptor modeling of the data set by positive matrix factorization (PMF was used to identify six sources contributing to PM2.5 and PM10 concentrations at the site. Dominant sources included industrial coal combustion, secondary inorganic aerosol, motor vehicles and construction dust along with two intermittent sources (biomass combustion and marine aerosol. The biomass combustion source was found to be a significant contributor to peak PM2.5 episodes along with motor vehicles and industrial coal combustion. Conditional probability function (CPF analysis was applied to estimate the source locations using the PMF-resolved source contribution coupled with the surface wind direction data. Health exposure risk of hazardous trace elements (Pb, As, Si, Cr, Mn and Ni and source-specific values were estimated. The total hazard quotient (HQ of PM2.5 was 2.09, higher than the acceptable limit (HQ = 1. The total carcinogenic risk (CR was 3.37 × 10−3 for PM2.5, which was 3 times higher than the least stringent limit (1.0 × 10−4. Among the selected trace elements, As and Pb posed the highest non-carcinogenic and carcinogenic risks to human health, respectively. In addition, our results show that the industrial coal combustion source is the dominant non-carcinogenic and carcinogenic risk contributor, highlighting the need for stringent control of this source. This study provides new insight for policy makers to prioritize sources in air quality management and health risk reduction.

Characterizing Aggregated Exposure to Primary Particulate Matter: Recommended Intake Fractions for Indoor and Outdoor Sources

DEFF Research Database (Denmark)

Fantke, Peter; Jolliet, Olivier; Apte, Joshua Schulz

2017-01-01

Exposure to fine particulate matter (PM_(2.5)) from indoor and outdoor sources is a leading environmental contributor to global disease burden. In response, we established under the auspices of the UNEP/SETAC Life Cycle Initiative a coupled indoor-outdoor emission-to-exposure framework to provide...

Source Apportionment of PM2.5 in Delhi, India Using PMF Model.

Science.gov (United States)

Sharma, S K; Mandal, T K; Jain, Srishti; Saraswati; Sharma, A; Saxena, Mohit

2016-08-01

Chemical characterization of PM2.5 [organic carbon, elemental carbon, water soluble inorganic ionic components, and major and trace elements] was carried out for a source apportionment study of PM2.5 at an urban site of Delhi, India from January, 2013, to December, 2014. The annual average mass concentration of PM2.5 was 122 ± 94.1 µg m(-3). Strong seasonal variation was observed in PM2.5 mass concentration and its chemical composition with maxima during winter and minima during monsoon. A receptor model, positive matrix factorization (PMF) was applied for source apportionment of PM2.5 mass concentration. The PMF model resolved the major sources of PM2.5 as secondary aerosols (21.3 %), followed by soil dust (20.5 %), vehicle emissions (19.7 %), biomass burning (14.3 %), fossil fuel combustion (13.7 %), industrial emissions (6.2 %) and sea salt (4.3 %).

Fractionation of trace elements and human health risk of submicron particulate matter (PM1) collected in the surroundings of coking plants.

Science.gov (United States)

Zajusz-Zubek, Elwira; Radko, Tomasz; Mainka, Anna

2017-08-01

Samples of PM1 were collected in the surroundings of coking plants located in southern Poland. Chemical fractionation provided information on the contents of trace elements As, Cd, Co, Cr, Hg, Mn, Ni, Pb, Sb and Se in all mobile (F1-F3) and not mobile (F4) fractions of PM1 in the vicinity of large sources of emissions related to energochemical processing of coal during the summer. The determined enrichment factors indicate the influence of anthropogenic sources on the concentration of the examined elements contained in PM1 in the areas subjected to investigation. The analysis of health risk for the assumed scenario of inhabitant exposure to the toxic effect of elements, based on the values of the hazard index, revealed that the absorption of the examined elements contained in the most mobile fractions of particulate matter via inhalation by children and adults can be considered potentially harmless to the health of people inhabiting the surroundings of coking plants during the summer (HI PM1, approximately four adults and one child out of one million people living in the vicinity of the coking plants may develop cancer.

Elemental characterization and source apportionment of PM{sub 10} and PM{sub 2.5} in the western coastal area of central Taiwan

Energy Technology Data Exchange (ETDEWEB)

Hsu, Chin-Yu; Chiang, Hung-Che [National Environmental Health Research Center, National Health Research Institutes, 35 Keyan Road, Zhunan Town, Miaoli 35053, Taiwan (China); Lin, Sheng-Lun [Super Micro Mass Research and Technology Center, Cheng Shiu University, No. 840, Chengcing Rd., Kaohsiung 83347, Taiwan (China); Chen, Mu-Jean; Lin, Tzu-Yu [National Environmental Health Research Center, National Health Research Institutes, 35 Keyan Road, Zhunan Town, Miaoli 35053, Taiwan (China); Chen, Yu-Cheng, E-mail: yucheng@nhri.org.tw [National Environmental Health Research Center, National Health Research Institutes, 35 Keyan Road, Zhunan Town, Miaoli 35053, Taiwan (China); Department of Occupational Safety and Health, China Medical University, 91 Hsueh-Shih Road, Taichung 40402, Taiwan (China)

2016-01-15

ABSTRACT: This study investigated seasonal variations in PM{sub 10} and PM{sub 2.5} mass and associated trace metal concentrations in a residential area in proximity to the crude oil refinery plants and industrial parks of central Taiwan. Particle measurements were conducted during winter, spring and summer in 2013 and 2014. Twenty-six trace metals in PM{sub 10} and PM{sub 2.5} were analyzed using ICP-MS. Multiple approaches of the backward trajectory model, enrichment factor (EF), Lanthanum enrichment and positive matrix fraction (PMF) were used to identify potential sources of particulate metals. Mean concentrations of PM{sub 10} in winter, spring and summer were 76.4 ± 22.6, 33.2 ± 9.9 and 37.4 ± 17.0 μg m{sup −3}, respectively, while mean levels of PM{sub 2.5} in winter, spring and summer were 47.8 ± 20.0, 23.9 ± 11.2 and 16.3 ± 8.2 μg m{sup −3}, respectively. The concentrations of carcinogenic metals (Ni, As and adjusted Cr(VI)) in PM{sub 10} and PM{sub 2.5} exceeded the guideline limits published by WHO. The result of EF analysis confirmed that Mo, Sb, Cd, Zn, Mg, Cr, As, Pb, Cu, Ni and V were attributable to anthropogenic emission. PMF analysis demonstrated that trace metals in PM{sub 10} and PM{sub 2.5} were from the similar sources, such as coal combustion, oil combustion and traffic-related emission, except for soil dust and crustal element emissions only observed in PM{sub 10} and secondary aluminum smelter only observed in PM{sub 2.5}. Considering health-related particulate metals, the traffic-related emission and coal combustion for PM{sub 10} and PM{sub 2.5}, respectively, are important to control for reducing potential carcinogenic risk. The results could aid efforts to clarify the impact of source-specific origins on human health. - Highlights: • Multiple approaches to identify sources of PM{sub 10} and PM{sub 2.5} metals were used. • Four similar sources contributed to metals in PM{sub 10} and PM{sub 2.5} in the study area. • Six

Controlling particulate matter under the Clean Air Act: a menu of options

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

This document was prepared by STAPPA and ALAPCO to help US state and local air pollution control officials understand the effects of particulate matter (PM) on human health and air quality, the relative contribution of various sources to particulate emissions, and the effectiveness and costs of various approaches - including innovative ones - to minimizing these emissions. The document covers particulate matter with a nominal diameter of 10 microns ({mu}m) or less (PM{sub 10}), including `fine` PM of 2.5 microns or less in diameter (PM{sub 2.5}). Sections cover: the effects of particulate matter on human health; regulatory issues; characterization of particulate matter; emission control strategies for mobile sources (diesel engines, small nonroad engines, alternative fuels etc.), particulates from stationary sources (electric utilities, industry and commercial fuel combustion; mineral products industry, metallurgical industry etc.); particulates from area sources; and market-based strategies for controlling particulate matter. 2 apps.

Source Apportionment and Influencing Factor Analysis of Residential Indoor PM2.5 in Beijing

Science.gov (United States)

Yang, Yibing; Liu, Liu; Xu, Chunyu; Li, Na; Liu, Zhe; Wang, Qin; Xu, Dongqun

2018-01-01

In order to identify the sources of indoor PM2.5 and to check which factors influence the concentration of indoor PM2.5 and chemical elements, indoor concentrations of PM2.5 and its related elements in residential houses in Beijing were explored. Indoor and outdoor PM2.5 samples that were monitored continuously for one week were collected. Indoor and outdoor concentrations of PM2.5 and 15 elements (Al, As, Ca, Cd, Cu, Fe, K, Mg, Mn, Na, Pb, Se, Tl, V, Zn) were calculated and compared. The median indoor concentration of PM2.5 was 57.64 μg/m3. For elements in indoor PM2.5, Cd and As may be sensitive to indoor smoking, Zn, Ca and Al may be related to indoor sources other than smoking, Pb, V and Se may mainly come from outdoor. Five factors were extracted for indoor PM2.5 by factor analysis, explained 76.8% of total variance, outdoor sources contributed more than indoor sources. Multiple linear regression analysis for indoor PM2.5, Cd and Pb was performed. Indoor PM2.5 was influenced by factors including outdoor PM2.5, smoking during sampling, outdoor temperature and time of air conditioner use. Indoor Cd was affected by factors including smoking during sampling, outdoor Cd and building age. Indoor Pb concentration was associated with factors including outdoor Pb and time of window open per day, building age and RH. In conclusion, indoor PM2.5 mainly comes from outdoor sources, and the contributions of indoor sources also cannot be ignored. Factors associated indoor and outdoor air exchange can influence the concentrations of indoor PM2.5 and its constituents. PMID:29621164

Personal exposure measurements of school-children to fine particulate matter (PM2.5) in winter of 2013, Shanghai, China.

Science.gov (United States)

Zhang, Lijun; Guo, Changyi; Jia, Xiaodong; Xu, Huihui; Pan, Meizhu; Xu, Dong; Shen, Xianbiao; Zhang, Jianghua; Tan, Jianguo; Qian, Hailei; Dong, Chunyang; Shi, Yewen; Zhou, Xiaodan; Wu, Chen

2018-01-01

The aim of this study was to perform an exposure assessment of PM2.5 (particulate matter less than 2.5μm in aerodynamic diameter) among children and to explore the potential sources of exposure from both indoor and outdoor environments. In terms of real-time exposure measurements of PM2.5, we collected data from 57 children aged 8-12 years (9.64 ± 0.93 years) in two schools in Shanghai, China. Simultaneously, questionnaire surveys and time-activity diaries were used to estimate the environment at home and daily time-activity patterns in order to estimate the exposure dose of PM2.5 in these children. Principle component regression analysis was used to explore the influence of potential sources of PM2.5 exposure. All the median personal exposure and microenvironment PM2.5 concentrations greatly exceeded the daily 24-h PM2.5 Ambient Air Quality Standards of China, the USA, and the World Health Organization (WHO). The median Etotal (the sum of the PM2.5 exposure levels in different microenvironment and fractional time) of all students was 3014.13 (μg.h)/m3. The concentration of time-weighted average (TWA) exposure of all students was 137.01 μg/m3. The median TWA exposure level during the on-campus period (135.81 μg/m3) was significantly higher than the off-campus period (115.50 μg/m3, P = 0.013 < 0.05). Besides ambient air pollution and meteorological conditions, storey height of the classroom and mode of transportation to school were significantly correlated with children's daily PM2.5 exposure. Children in the two selected schools were exposed to high concentrations of PM2.5 in winter of 2013 in Shanghai. Their personal PM2.5 exposure was mainly associated with ambient air conditions, storey height of the classroom, and children's transportation mode to school.

Numerical simulations for the sources apportionment and control strategies of PM2.5 over Pearl River Delta, China, part I: Inventory and PM2.5 sources apportionment.

Science.gov (United States)

Huang, Yeqi; Deng, Tao; Li, Zhenning; Wang, Nan; Yin, Chanqin; Wang, Shiqiang; Fan, Shaojia

2018-09-01

This article uses the WRF-CMAQ model to systematically study the source apportionment of PM 2.5 under typical meteorological conditions in the dry season (November 2010) in the Pearl River Delta (PRD). According to the geographical location and the relative magnitude of pollutant emission, Guangdong Province is divided into eight subdomains for source apportionment study. The Brute-Force Method (BFM) method was implemented to simulate the contribution from different regions to the PM 2.5 pollution in the PRD. Results show that the industrial sources accounted for the largest proportion. For emission species, the total amount of NO x and VOC in Guangdong Province, and NH 3 and VOC in Hunan Province are relatively larger. In Guangdong Province, the emission of SO 2 , NO x and VOC in the PRD are relatively larger, and the NH 3 emissions are higher outside the PRD. In northerly-controlled episodes, model simulations demonstrate that local emissions are important for PM 2.5 pollution in Guangzhou and Foshan. Meanwhile, emissions from Dongguan and Huizhou (DH), and out of Guangdong Province (SW) are important contributors for PM 2.5 pollution in Guangzhou. For PM 2.5 pollution in Foshan, emissions in Guangzhou and DH are the major contributors. In addition, high contribution ratio from DH only occurs in severe pollution periods. In southerly-controlled episode, contribution from the southern PRD increases. Local emissions and emissions from Shenzhen, DH, Zhuhai-Jiangmen-Zhongshan (ZJZ) are the major contributors. Regional contribution to the chemical compositions of PM 2.5 indicates that the sources of chemical components are similar to those of PM 2.5 . In particular, SO 4 2- is mainly sourced from emissions out of Guangdong Province, while the NO 3- and NH 4+ are more linked to agricultural emissions. Copyright © 2018 Elsevier B.V. All rights reserved.

Characterization of Fine Particulate Matter (PM) and Secondary PM Precursor Gases in the Mexico City Metropolitan Area

Energy Technology Data Exchange (ETDEWEB)

Molina, Luisa T.; Molina, Mario J.; Volkamer, Rainer; de Foy, Benjamin; Lei, Wenfang; Zavaka, Miguel; Velasco, Erik

2008-10-31

This project was one of three collaborating grants funded by DOE/ASP to characterize the fine particulate matter (PM) and secondary PM precursors in the Mexico City Metropolitan Area (MCMA) during the MILAGRO Campaign. The overall effort of MCMA-2006, one of the four components, focused on i) examination of the primary emissions of fine particles and precursor gases leading to photochemical production of atmospheric oxidants and secondary aerosol particles; ii) measurement and analysis of secondary oxidants and secondary fine PM production, with particular emphasis on secondary organic aerosol (SOA), and iii) evaluation of the photochemical and meteorological processes characteristic of the Mexico City Basin. The collaborative teams pursued the goals through three main tasks: i) analyses of fine PM and secondary PM precursor gaseous species data taken during the MCMA-2002/2003 campaigns and preparation of publications; ii) planning of the MILAGRO Campaign and deployment of the instrument around the MCMA; and iii) analysis of MCMA-2006 data and publication preparation. The measurement phase of the MILAGRO Campaign was successfully completed in March 2006 with excellent participation from the international scientific community and outstanding cooperation from the Mexican government agencies and institutions. The project reported here was led by the Massachusetts Institute of Technology/Molina Center for Energy and the Environment (MIT/MCE2) team and coordinated with DOE/ASP-funded collaborators at Aerodyne Research Inc., University of Colorado at Boulder and Montana State University. Currently 24 papers documenting the findings from this project have been published. The results from the project have improved significantly our understanding of the meteorological and photochemical processes contributing to the formation of ozone, secondary aerosols and other pollutants. Key findings from the MCMA-2003 include a vastly improved speciated emissions inventory from on

Mass concentration, composition and sources of fine and coarse particulate matter in Tijuana, Mexico, during Cal-Mex campaign

Science.gov (United States)

Minguillón, María Cruz; Campos, Arturo Alberto; Cárdenas, Beatriz; Blanco, Salvador; Molina, Luisa T.; Querol, Xavier

2014-05-01

This work was carried out in the framework of the Cal-Mex project, which focuses on investigating the atmosphere along Mexico-California border region. Sampling was carried out at two sites located in Tijuana urban area: Parque Morelos and Metales y Derivados. PM2.5 and PM10 24 h samples were collected every three days from 17th May 2010 to 27th June 2010, and were used for gravimetric and chemical analyses (major and minor elements, inorganic ions, organic and elemental carbon) of PM. A subsequent Positive Matrix Factorization (PMF) analysis was performed. PM2.5 and PM10 average concentrations during Cal-Mex were relatively lower compared to usual annual averages. Trace elements concentrations recorded in the present study were lower than those recorded in Mexico City in 2006, with the exception of Pb at Metales y Derivados, attributed to the influence of a specific industrial source, which also includes As, Cd and Tl. Apart from this industrial source, both urban sites were found to be affected by similar sources with respect to bulk PM. Fine PM (PM2.5) was mainly apportioned by fueloil and biomass combustion and secondary aerosols, and road traffic. Coarse PM (PM2.5-10) was mainly apportioned by a mineral source (sum of road dust resuspension, construction emissions and natural soil) and fresh and aged sea salt. The road traffic was responsible for more than 60% of the fine elemental carbon and almost 40% of the fine organic matter.

Fine particulate matter in the indoor air of barbeque restaurants: Elemental compositions, sources and health risks

International Nuclear Information System (INIS)

Taner, Simge; Pekey, Beyhan; Pekey, Hakan

2013-01-01

Cooking is a significant source of indoor particulate matter that can cause adverse health effects. In this study, a 5-stage cascade impactor was used to collect particulate matter from 14 restaurants that cooked with charcoal in Kocaeli, the second largest city in Turkey. A total of 24 elements were quantified using ICP-MS. All of the element contents except for Mn were higher for fine particles (PM 2.5 ) than coarse particles (PM >2.5 ), and the major trace elements identified in the PM 2.5 included V, Se, Zn, Cr, As, Cu, Ni, and Pb. Principle component analysis (PCA) and enrichment factor (EF) calculations were used to determine the sources of PM 2.5 . Four factors that explained over 77% of the total variance were identified by the PCA. These factors included charcoal combustion, indoor activities, crustal components, and road dust. The Se, As, Cd, and V contents in the PM 2.5 were highly enriched (EF > 100). The health risks posed by the individual metals were calculated to assess the potential health risks associated with inhaling the fine particles released during charcoal cooking. The total hazard quotient (total HQ) for a PM 2.5 of 4.09 was four times greater than the acceptable limit (i.e., 1.0). In addition, the excess lifetime cancer risk (total ELCR) for PM 2.5 was 1.57 × 10 −4 , which is higher than the acceptable limit of 1.0 × 10 −6 . Among all of the carcinogenic elements present in the PM 2.5 , the cancer risks resulting from Cr(VI) and As exposure were the highest (i.e., 1.16 × 10 −4 and 3.89 × 10 −5 , respectively). Overall, these results indicate that the lifetime cancer risk associated with As and Cr(VI) exposure is significant at selected restaurants, which is of concern for restaurant workers. - Highlights: • Particulate emissions from charcoal combustion in the BBQ restaurants were studied. • Vanadium, Se, Zn, Cr and As were found as high concentrations in PM 2.5 . • Charcoal combustion and indoor activities were the

Fine particulate matter in the indoor air of barbeque restaurants: Elemental compositions, sources and health risks

Energy Technology Data Exchange (ETDEWEB)

Taner, Simge; Pekey, Beyhan, E-mail: bpekey@kocaeli.edu.tr; Pekey, Hakan

2013-06-01

Cooking is a significant source of indoor particulate matter that can cause adverse health effects. In this study, a 5-stage cascade impactor was used to collect particulate matter from 14 restaurants that cooked with charcoal in Kocaeli, the second largest city in Turkey. A total of 24 elements were quantified using ICP-MS. All of the element contents except for Mn were higher for fine particles (PM{sub 2.5}) than coarse particles (PM{sub >2.5}), and the major trace elements identified in the PM{sub 2.5} included V, Se, Zn, Cr, As, Cu, Ni, and Pb. Principle component analysis (PCA) and enrichment factor (EF) calculations were used to determine the sources of PM{sub 2.5}. Four factors that explained over 77% of the total variance were identified by the PCA. These factors included charcoal combustion, indoor activities, crustal components, and road dust. The Se, As, Cd, and V contents in the PM{sub 2.5} were highly enriched (EF > 100). The health risks posed by the individual metals were calculated to assess the potential health risks associated with inhaling the fine particles released during charcoal cooking. The total hazard quotient (total HQ) for a PM{sub 2.5} of 4.09 was four times greater than the acceptable limit (i.e., 1.0). In addition, the excess lifetime cancer risk (total ELCR) for PM{sub 2.5} was 1.57 × 10{sup −4}, which is higher than the acceptable limit of 1.0 × 10{sup −6}. Among all of the carcinogenic elements present in the PM{sub 2.5}, the cancer risks resulting from Cr(VI) and As exposure were the highest (i.e., 1.16 × 10{sup −4} and 3.89 × 10{sup −5}, respectively). Overall, these results indicate that the lifetime cancer risk associated with As and Cr(VI) exposure is significant at selected restaurants, which is of concern for restaurant workers. - Highlights: • Particulate emissions from charcoal combustion in the BBQ restaurants were studied. • Vanadium, Se, Zn, Cr and As were found as high concentrations in PM{sub 2.5}. �

Anomalous elevated radiocarbon measurements of PM2.5

International Nuclear Information System (INIS)

Buchholz, Bruce A.; Fallon, Stewart J.; Zermeño, Paula; Bench, Graham; Schichtel, Bret A.

2013-01-01

Two-component models are often used to determine the contributions made by fossil fuel and natural sources of carbon in airborne particulate matter (PM). The models reduce thousands of actual sources to two end members based on isotopic signature. Combustion of fossil fuels produces PM free of carbon-14 ( 14 C). Wood or charcoal smoke, restaurant fryer emissions, and natural emissions from plants produce PM with the contemporary concentration of 14 C approximately 1.2 × 10 −1214 C/C. Such data can be used to estimate the relative contributions of fossil fuels and biogenic aerosols to the total aerosol loading and radiocarbon analysis is becoming a popular source apportionment method. Emissions from incinerators combusting medical or biological wastes containing tracer 14 C can skew the 14 C/C ratio of PM, however, so critical analysis of sampling sites for possible sources of elevated PM needs to be completed prior to embarking on sampling campaigns. Results are presented for two ambient monitoring sites in different areas of the United States where 14 C contamination is apparent. Our experience suggests that such contamination is uncommon but is also not rare (∼10%) for PM sampling sites.

Quantification of source impact to PM using three-dimensional weighted factor model analysis on multi-site data

Science.gov (United States)

Shi, Guoliang; Peng, Xing; Huangfu, Yanqi; Wang, Wei; Xu, Jiao; Tian, Yingze; Feng, Yinchang; Ivey, Cesunica E.; Russell, Armistead G.

2017-07-01

Source apportionment technologies are used to understand the impacts of important sources of particulate matter (PM) air quality, and are widely used for both scientific studies and air quality management. Generally, receptor models apportion speciated PM data from a single sampling site. With the development of large scale monitoring networks, PM speciation are observed at multiple sites in an urban area. For these situations, the models should account for three factors, or dimensions, of the PM, including the chemical species concentrations, sampling periods and sampling site information, suggesting the potential power of a three-dimensional source apportionment approach. However, the principle of three-dimensional Parallel Factor Analysis (Ordinary PARAFAC) model does not always work well in real environmental situations for multi-site receptor datasets. In this work, a new three-way receptor model, called "multi-site three way factor analysis" model is proposed to deal with the multi-site receptor datasets. Synthetic datasets were developed and introduced into the new model to test its performance. Average absolute error (AAE, between estimated and true contributions) for extracted sources were all less than 50%. Additionally, three-dimensional ambient datasets from a Chinese mega-city, Chengdu, were analyzed using this new model to assess the application. Four factors are extracted by the multi-site WFA3 model: secondary source have the highest contributions (64.73 and 56.24 μg/m3), followed by vehicular exhaust (30.13 and 33.60 μg/m3), crustal dust (26.12 and 29.99 μg/m3) and coal combustion (10.73 and 14.83 μg/m3). The model was also compared to PMF, with general agreement, though PMF suggested a lower crustal contribution.

In vitro investigations of platinum, palladium, and rhodium mobility in urban airborne particulate matter (PM10, PM2.5, and PM1) using simulated lung fluids.

Science.gov (United States)

Zereini, Fathi; Wiseman, Clare L S; Püttmann, Wilhelm

2012-09-18

Environmental concentrations of platinum group elements (PGE) have been increasing since the introduction of automotive catalytic converters to control harmful emissions. Assessments of the human health risks of exposures to these elements, especially through the inhalation of PGE-associated airborne particulate matter (PM), have been hampered by a lack of data on their bioaccessibility. The purpose of this study is to apply in vitro methods using simulated human lung fluids [artificial lysosomal fluid (ALF) and Gamble's solution] to assess the mobility of the PGE, platinum (Pt), palladium (Pd), and rhodium (Rh) in airborne PM of human health concern. Airborne PM samples (PM(10), PM(2.5), and PM(1)) were collected in Frankfurt am Main, Germany. For comparison, the same extraction experiments were conducted using the standard reference material, Used Auto Catalyst (monolith) (NIST 2557). Pt and Pd concentrations were measured using isotope dilution ICP-Q-MS, while Rh was measured directly with ICP-Q-MS (in collision mode with He), following established matrix separation and enrichment procedures, for both solid (filtered residues) and extracted sample phases. The mobilized fractions measured for PGE in PM(10), PM(2.5), and PM(1) were highly variable, which can be attributed to the heterogenic nature of airborne PM and its composition. Overall, the mobility of PGE in airborne PM samples was notable, with a mean of 51% Rh, 22% Pt, and 29% Pd present in PM(1) being mobilized by ALF after 24 h. For PM(1) exposed to Gamble's solution, a mean of 44% Rh, 18% Pt, and 17% Pd was measured in solution after 24 h. The mobility of PGE associated with airborne PM was also determined to be much higher compared to that measured for the auto catalyst standard reference material. The results suggest that PGE emitted from automotive catalytic converters are likely to undergo chemical transformations during and/or after being emitted in the environment. This study highlights the need

Quantifying the sources of ozone, fine particulate matter, and regional haze in the Southeastern United States.

Science.gov (United States)

Odman, M Talat; Hu, Yongtao; Russell, Armistead G; Hanedar, Asude; Boylan, James W; Brewer, Patricia F

2009-07-01

A detailed sensitivity analysis was conducted to quantify the contributions of various emission sources to ozone (O3), fine particulate matter (PM2.5), and regional haze in the Southeastern United States. O3 and particulate matter (PM) levels were estimated using the Community Multiscale Air Quality (CMAQ) modeling system and light extinction values were calculated from modeled PM concentrations. First, the base case was established using the emission projections for the year 2009. Then, in each model run, SO2, primary carbon (PC), NH3, NO(x) or VOC emissions from a particular source category in a certain geographic area were reduced by 30% and the responses were determined by calculating the difference between the results of the reduced emission case and the base case. The sensitivity of summertime O3 to VOC emissions is small in the Southeast and ground-level NO(x) controls are generally more beneficial than elevated NO(x) controls (per unit mass of emissions reduced). SO2 emission reduction is the most beneficial control strategy in reducing summertime PM2.5 levels and improving visibility in the Southeast and electric generating utilities are the single largest source of SO2. Controlling PC emissions can be very effective locally, especially in winter. Reducing NH3 emissions is an effective strategy to reduce wintertime ammonium nitrate (NO3NH4) levels and improve visibility; NO(x) emissions reductions are not as effective. The results presented here will help the development of specific emission control strategies for future attainment of the National Ambient Air Quality Standards in the region.

Simultaneous monitoring and compositions analysis of PM1 and PM2.5 in Shanghai: Implications for characterization of haze pollution and source apportionment.

Science.gov (United States)

Qiao, Ting; Zhao, Mengfei; Xiu, Guangli; Yu, Jianzhen

2016-07-01

A year-long simultaneous observation of PM1 and PM2.5 were conducted at ECUST campus in Shanghai, the compositions were analyzed and compared. Results showed that PM2.5 was dominated by PM1 on clear days while the contribution of PM1-2.5 to PM2.5 increased on haze days, indicating that PM2.5 should be given priority to characterize or predict haze pollution. On haze days, accumulation of organic carbon (OC), elemental carbon (EC) and primary organic carbon (POC) in PM1-2.5 was faster than that in PM1. Humic-like substances carbon (Hulis-C) in both PM2.5 and PM1 formed faster than water soluble organic carbon (WSOC) on haze days, hence Hulis-C/WSOC increased with the intensification of haze pollution. In terms of water soluble ions, NO3(-)/SO4(2-) in PM1 increased with the aggravation of haze pollution, implying that mobile sources dominated on haze days, so is nitrogen oxidation ratio (NOR). Liquid water content (LWC) in both PM1 and PM2.5 had positive correlations with relative humidity (RH) but negative correlations with visibility, implying that hygroscopic growth might be a factor for visibility impairment, especially LWC in PM1. By comparison with multi-linear equations of LWC in PM1 and PM2.5, NO3(-) exerted a higher influence on hygroscopicity of PM1 than PM2.5, while RH, WSOC, SO4(2-) and NH4(+) had higher effects on PM2.5, especially WSOC. Source apportionment of PM2.5 was also investigated to provide reference for policy making. Cluster analysis by HYSPLIT (HYbrid Single Particle Lagrangian Integrated Trajectory) model showed that PM2.5 originated from marine aerosols, middle-scale transportation and large-scale transportation. Furthermore, PM2.5 on haze days was dominated by middle-scale transportation. In line with source apportionment by positive matrix factorization (PMF) model, PM2.5 was attributed to secondary inorganics, aged sea salt, combustion emissions, hygroscopic growth and secondary organics. Secondary formation was the principle source of

Sources and Processes Affecting Particulate Matter Pollution over North China

Science.gov (United States)

Zhang, L.; Shao, J.; Lu, X.; Zhao, Y.; Gong, S.; Henze, D. K.

2015-12-01

Severe fine particulate matter (PM2.5) pollution over North China has received broad attention worldwide in recent years. Better understanding the sources and processes controlling pollution over this region is of great importance with urgent implications for air quality policy. We will present a four-dimensional variational (4D-Var) data assimilation system using the GEOS-Chem chemical transport model and its adjoint model at 0.25° × 0.3125° horizontal resolution, and apply it to analyze the factors affecting PM2.5 concentrations over North China. Hourly surface observations of PM2.5 and sulfur dioxide (SO2) from the China National Environmental Monitoring Center (CNEMC) can be assimilated into the model to evaluate and constrain aerosol (primary and precursors) emissions. Application of the data assimilation system to the APEC period (the Asia-Pacific Economic Cooperation summit; 5-11 November 2014) shows that 46% of the PM2.5 pollution reduction during APEC ("The APEC Blue") can be attributed to meteorology conditions and the rest 54% to emission reductions due to strict emission controls. Ammonia emissions are shown to significantly contribute to PM2.5 over North China in the fall. By converting sulfuric acid and nitric acid to longer-lived ammonium sulfate and ammonium nitrate aerosols, ammonia plays an important role in promoting their regional transport influences. We will also discuss the pathways and mechanisms of external long-range transport influences to the PM2.5 pollution over North China.

Seasonal characteristics, formation mechanisms and source origins of PM2.5 in two megacities in Sichuan Basin, China

Science.gov (United States)

Wang, Huanbo; Tian, Mi; Chen, Yang; Shi, Guangming; Liu, Yuan; Yang, Fumo; Zhang, Leiming; Deng, Liqun; Yu, Jiayan; Peng, Chao; Cao, Xuyao

2018-01-01

To investigate the characteristics of PM2.5 and its major chemical components, formation mechanisms, and geographical origins in the two megacities, Chengdu (CD) and Chongqing (CQ), in Sichuan Basin of southwest China, daily PM2.5 samples were collected simultaneously at one urban site in each city for four consecutive seasons from autumn 2014 to summer 2015. Annual mean concentrations of PM2.5 were 67.0 ± 43.4 and 70.9 ± 41.4 µg m-3 at CD and CQ, respectively. Secondary inorganic aerosol (SNA) and organic matter (OM) accounted for 41.1 and 26.1 % of PM2.5 mass at CD, and 37.4 and 29.6 % at CQ, respectively. Seasonal variations of PM2.5 and major chemical components were significant, usually with the highest mass concentration in winter and the lowest in summer. Daily PM2.5 concentration exceeded the national air quality standard on 30 % of the sampling days at both sites, and most of the pollution events were at the regional scale within the basin formed under stagnant meteorological conditions. The concentrations of carbonaceous components were higher at CQ than CD, likely partially caused by emissions from the large number of motorcycles and the spraying processes used during automobile production in CQ. Heterogeneous reactions probably played an important role in the formation of SO42-, while both homogeneous and heterogeneous reactions contributed to the formation of NO3-. Geographical origins of emissions sources contributing to high PM2.5 masses at both sites were identified to be mainly distributed within the basin based on potential source contribution function (PSCF) analysis.

Assessment of light extinction at a European polluted urban area during wintertime: Impact of PM1 composition and sources.

Science.gov (United States)

Vecchi, R; Bernardoni, V; Valentini, S; Piazzalunga, A; Fermo, P; Valli, G

2018-02-01

In this paper, results from receptor modelling performed on a well-characterised PM 1 dataset were combined to chemical light extinction data (b ext ) with the aim of assessing the impact of different PM 1 components and sources on light extinction and visibility at a European polluted urban area. It is noteworthy that, at the state of the art, there are still very few papers estimating the impact of different emission sources on light extinction as we present here, although being among the major environmental challenges at many polluted areas. Following the concept of the well-known IMPROVE algorithm, here a tailored site-specific approach (recently developed by our group) was applied to assess chemical light extinction due to PM 1 components and major sources. PM 1 samples collected separately during daytime and nighttime at the urban area of Milan (Italy) were chemically characterised for elements, major ions, elemental and organic carbon, and levoglucosan. Chemical light extinction was estimated and results showed that at the investigated urban site it is heavily impacted by ammonium nitrate and organic matter. Receptor modelling (i.e. Positive Matrix Factorization, EPA-PMF 5.0) was effective to obtain source apportionment; the most reliable solution was found with 7 factors which were tentatively assigned to nitrates, sulphates, wood burning, traffic, industry, fine dust, and a Pb-rich source. The apportionment of aerosol light extinction (b ext,aer ) according to resolved sources showed that considering all samples together nitrate contributed at most (on average 41.6%), followed by sulphate, traffic, and wood burning accounting for 18.3%, 17.8% and 12.4%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Quantification of the sources of long-range transport of PM2.5 pollution in the Ordos region, Inner Mongolia, China

International Nuclear Information System (INIS)

Khuzestani, Reza Bashiri; Schauer, James J.; Wei, Yongjie; Zhang, Lulu; Cai, Tianqi; Zhang, Yang; Zhang, Yuanxun

2017-01-01

The Ordos region of Inner Mongolia is rapidly developing and suffers from poor air quality and unhealthy levels of fine particulate matter. PM 2.5 concentrations in the Ordos region were found to exceed 75 μg/m 3 on average, annually, with peak pollution days in excess of 350 μg/m 3 , but local air pollution emissions from surrounding sources are not sufficient to drive pollution levels to these concentrations. The current study was designed to quantify sources of PM 2.5 and assess the local source contributions and effects of regional transport on local pollution. The results show that the Ordos region is primarily impacted by regional long-range transport of pollutants from anthropogenic sources located outside of the Inner Mongolia in Shanxi province areas but is also largely affected by regional dust transported from the deserts located in western Inner Mongolia. The analysis proved that approximately 77% of PM 2.5 mass is transported long-range from the sites exterior to the study area and contributes 59.32 μg/m 3 on average, annually, while the local sources contribute 17.41 μg/m 3 (23%) on annual average to the PM 2.5 mass in the study area. High spatial correlation coefficients (R 2  > 0.6) were observed for most of the factors pointing to the transport of external emissions into the area. Spatial correlation analysis, bivariate polar plots and hybrid trajectory models for industrial and secondary inorganic factors provide evidence for the impact of long-range transport from Shanxi province areas. In addition, the deserts in western Inner Mongolia were found to be the source regions for dust. Finally, our analysis shows that the source of oil combustion and mobile factors are impacted by local sources in the Ordos region; however, some regional impacts from other regions were also observed for mobile source in the area. - Dominance of the regional long-range transport of PM 2.5 sources in the Ordos region. Around 77% of PM 2.5 mass is transported

Fine particulate matter in the tropical environment: monsoonal effects, source apportionment, and health risk assessment

Science.gov (United States)

Khan, M. F.; Latif, M. T.; Saw, W. H.; Amil, N.; Nadzir, M. S. M.; Sahani, M.; Tahir, N. M.; Chung, J. X.

2016-01-01

The health implications of PM2.5 in the tropical region of Southeast Asia (SEA) are significant as PM2.5 can pose serious health concerns. PM2.5 concentration and sources here are strongly influenced by changes in the monsoon regime from the south-west quadrant to the north-east quadrant in the region. In this work, PM2.5 samples were collected at a semi-urban area using a high-volume air sampler at different seasons on 24 h basis. Analysis of trace elements and water-soluble ions was performed using inductively coupled plasma mass spectroscopy (ICP-MS) and ion chromatography (IC), respectively. Apportionment analysis of PM2.5 was carried out using the United States Environmental Protection Agency (US EPA) positive matrix factorization (PMF) 5.0 and a mass closure model. We quantitatively characterized the health risks posed to human populations through the inhalation of selected heavy metals in PM2.5. 48 % of the samples collected exceeded the World Health Organization (WHO) 24 h PM2.5 guideline but only 19 % of the samples exceeded 24 h US EPA National Ambient Air Quality Standard (NAAQS). The PM2.5 concentration was slightly higher during the north-east monsoon compared to south-west monsoon. The main trace metals identified were As, Pb, Cd, Ni, Mn, V, and Cr while the main ions were SO42-, NO3-, NH4+, and Na. The mass closure model identified four major sources of PM2.5 that account for 55 % of total mass balance. The four sources are mineral matter (MIN) (35 %), secondary inorganic aerosol (SIA) (11 %), sea salt (SS) (7 %), and trace elements (TE) (2 %). PMF 5.0 elucidated five potential sources: motor vehicle emissions coupled with biomass burning (31 %) were the most dominant, followed by marine/sulfate aerosol (20 %), coal burning (19 %), nitrate aerosol (17 %), and mineral/road dust (13 %). The hazard quotient (HQ) for four selected metals (Pb, As, Cd, and Ni) in PM2.5 mass was highest in PM2.5 mass from the coal burning source and least in PM2.5 mass

Identifying the sources driving observed PM2.5 temporal variability over Halifax, Nova Scotia, during BORTAS-B

Directory of Open Access Journals (Sweden)

M. D. Gibson

2013-07-01

Full Text Available The source attribution of observed variability of total PM2.5 concentrations over Halifax, Nova Scotia, was investigated between 11 July and 26 August 2011 using measurements of PM2.5 mass and PM2.5 chemical composition (black carbon, organic matter, anions, cations and 33 elements. This was part of the BORTAS-B (quantifying the impact of BOReal forest fires on Tropospheric oxidants using Aircraft and Satellites experiment, which investigated the atmospheric chemistry and transport of seasonal boreal wildfire emissions over eastern Canada in 2011. The US EPA Positive Matrix Factorization (PMF receptor model was used to determine the average mass (percentage source contribution over the 45 days, which was estimated to be as follows: long-range transport (LRT pollution: 1.75 μg m−3 (47%; LRT pollution marine mixture: 1.0 μg m−3 (27.9%; vehicles: 0.49 μg m−3 (13.2%; fugitive dust: 0.23 μg m−3 (6.3%; ship emissions: 0.13 μg m−3 (3.4%; and refinery: 0.081 μg m−3 (2.2%. The PMF model describes 87% of the observed variability in total PM2.5 mass (bias = 0.17 and RSME = 1.5 μg m−3. The factor identifications are based on chemical markers, and they are supported by air mass back trajectory analysis and local wind direction. Biomass burning plumes, found by other surface and aircraft measurements, were not significant enough to be identified in this analysis. This paper presents the results of the PMF receptor modelling, providing valuable insight into the local and upwind sources impacting surface PM2.5 in Halifax and a vital comparative data set for the other collocated ground-based observations of atmospheric composition made during BORTAS-B.

Chemical characterisation and source apportionment of PM1 during massive loading at an urban location in Indo-Gangetic Plain: impact of local sources and long-range transport

Directory of Open Access Journals (Sweden)

Prashant Rajput

2016-07-01

Full Text Available This study assesses temporal variability and source contributions of PM1 (particles with aerodynamic diameter ≤ 1.0 µm samples (n=51; November 2009–February 2010 from an urban location at Kanpur (26.30°N; 80.13°E; 142 m above mean sea-level in the Indo-Gangetic Plain (IGP. A study period from November to February is preferred owing to massive loading of particulate matter in entire IGP. PM1 varies from 18 to 348 (Avg±SD: 113±72 µg m−3 in this study. A total of 11 trace metals, five major elements and four water-soluble inorganic species (WSIS have been measured. Mass fraction of total metals (∑metals=trace+major centres at 18±14 %, of which nearly 15 % is contributed by major elements. Furthermore, ∑WSIS contributes about 26 % to PM1 mass concentration. Abundance pattern among assessed WSIS in this study follows the order: ≈> > Cl−. The K-to-PM1 mass fraction (Avg: 2 % in conjunction with air-mass back trajectories (AMBT indicates that the prevailing north-westerly winds transport biomass burning derived pollutants from upwind IGP. A recent version of positive matrix factorisation (PMF 5.0 has been utilised to quantify the contribution of fine-mode aerosols from various sources. The contribution from each source is highly variable and shows a strong dependence on AMBT. Events with predominant contribution from biomass burning emission (>70 % indicate origin of air-masses from source region upwind in IGP. One of the most interesting features of our study relates to the observation that secondary aerosols (contributing as high as ~60 % to PM1 loading are predominantly derived from stationary combustion sources (/ ratio: 0.30±0.23. Thus, our study highlights a high concentration of PM1 loading and atmospheric fog prevalent during wintertime can have a severe impact on atmospheric chemistry in the air-shed of IGP.

Demonstration of Novel Sampling Techniques for Measurement of Turbine Engine Volatile and Non-Volatile Particulate Matter (PM) Emissions

Science.gov (United States)

2017-03-06

WP-201317) Demonstration of Novel Sampling Techniques for Measurement of Turbine Engine Volatile and Non-volatile Particulate Matter (PM... Engine Volatile and Non-Volatile Particulate Matter (PM) Emissions 6. AUTHOR(S) E. Corporan, M. DeWitt, C. Klingshirn, M.D. Cheng, R. Miake-Lye, J. Peck...the performance and viability of two devices to condition aircraft turbine engine exhaust to allow the accurate measurement of total (volatile and non

Source apportionment of population representative samples of PM(2.5) in three European cities using structural equation modelling.

Science.gov (United States)

Ilacqua, Vito; Hänninen, Otto; Saarela, Kristina; Katsouyanni, Klea; Künzli, Nino; Jantunen, Matti

2007-10-01

Apportionment of urban particulate matter (PM) to sources is central for air quality management and efficient reduction of the substantial public health risks associated with fine particles (PM(2.5)). Traffic is an important source combustion particles, but also a significant source of resuspended particles that chemically resemble Earth's crust and that are not affected by development of cleaner motor technologies. A substantial fraction of urban ambient PM originates from long-range transport outside the immediate urban environment including secondary particles formed from gaseous emissions of mainly sulphur, nitrogen oxides and ammonia. Most source apportionment studies are based on small number of fixed monitoring sites and capture well population exposures to regional and long-range transported particles. However, concentrations from local sources are very unevenly distributed and the results from such studies are therefore poorly representative of the actual exposures. The current study uses PM(2.5) data observed at population based random sampled residential locations in Athens, Basle and Helsinki with 17 elemental constituents, selected VOCs (xylenes, trimethylbenzenes, nonane and benzene) and light absorbance (black smoke). The major sources identified across the three cities included crustal, salt, long-range transported inorganic and traffic sources. Traffic was associated separately with source categories with crustal (especially Athens and Helsinki) and long-range transported chemical composition (all cities). Remarkably high fractions of the variability of elemental (R(2)>0.6 except for Ca in Basle 0.38) and chemical concentrations (R(2)>0.5 except benzene in Basle 0.22 and nonane in Athens 0.39) are explained by the source factors of an SEM model. The RAINS model that is currently used as the main tool in developing European air quality management policies seems to capture the local urban fraction (the city delta term) quite well, but underestimates

Identification and characterization of fine and coarse particulate matter sources in a middle-European urban environment

International Nuclear Information System (INIS)

Kertesz, Zs.; Szoboszlai, Z.; Angyal, A.; Dobos, E.; Borbely-Kiss, I.

2010-01-01

In this work a source apportionment study is presented which aimed to characterize the PM 2.5 and PM 2.5-10 sources in the urban area of Debrecen, East-Hungary by using streaker samples, IBA methods and positive matrix factorization (PMF) analysis. Samples of fine (PM 2.5 ) and coarse (PM 2.5-10 ) urban particulate matter were collected with 2 h time resolution in the frame of five sampling campaigns during 2007-2009 in different seasons in the downtown of Debrecen. Elemental concentrations from Al to Pb of over 1000 samples were obtained by particle induced X-ray emission (PIXE); concentrations of black carbon (BC) were determined with a smoke stain reflectometer. On this data base source apportionment was carried out by using the PMF method. Seven factors were identified for both size fractions, including soil dust, traffic, secondary aerosol - sulphates, domestic heating, oil combustion, agriculture and an unknown factor enriched with chlorine. Seasonal and daily variation of the different factors was studied as well as their dependence on meteorological parameters. Besides determining the time patterns characteristic to the city, several emission episodes were identified including a Saharan dust intrusion on 21st-24th May, 2008.

Seasonal effect and source apportionment of polycyclic aromatic hydrocarbons in PM2.5

Science.gov (United States)

Khan, Md Firoz; Latif, Mohd Talib; Lim, Chee Hou; Amil, Norhaniza; Jaafar, Shoffian Amin; Dominick, Doreena; Mohd Nadzir, Mohd Shahrul; Sahani, Mazrura; Tahir, Norhayati Mohd

2015-04-01

This study aims to investigate distribution and sources of 16 polycyclic aromatic hydrocarbons (PAHs) bound to fine particulate matter (PM2.5) captured in a semi-urban area in Malaysia during different seasons, and to assess their health risks. PM2.5 samples were collected using a high volume air sampler on quartz filter paper at a flow rate of 1 m3 min-1 for 24 h. PAHs on the filter paper were extracted with dichloromethane (DCM) using an ultrasonic centrifuge solid-phase extraction method and measured by gas chromatography-mass spectroscopy. The results showed that the range of PAHs concentrations in the study period was between 0.21 and 12.08 ng m-3. The concentrations of PAHs were higher during the south-west monsoon (0.21-12.08 ng m-3) compared to the north-east monsoon (0.68-3.80 ng m-3). The high molecular weight (HMW) PAHs (≥5 ring) are significantly prominent (>70%) compared to the low molecular weight (LMW) PAHs (≤4 ring) in PM2.5. The Spearman correlation indicates that the LMW and HMW PAHs correlate strongly among themselves. The diagnostic ratios (DRs) of I[c]P/I[c]P + BgP and B[a]P/B[g]P suggest that the HMW PAHs originated from fuel combustion sources. The source apportionment analysis of PAHs was resolved using DRs-positive matrix factorization (PMF)-multiple linear regression (MLR). The main sources identified were (a) gasoline combustion (65%), (b) diesel and heavy oil combustion (19%) and (c) natural gas and coal burning (15%). The health risk evaluation, by means of the lifetime lung cancer risk (LLCR), showed no potential carcinogenic risk from the airborne BaPeq (which represents total PAHs at the present study area in Malaysia). The seasonal LLCR showed that the carcinogenic risk of total PAHs were two fold higher during south-westerly monsoon compared to north-easterly monsoon.

Source contributions to PM{sub 2.5} and PM{sub 10} at an urban background and a street location

Energy Technology Data Exchange (ETDEWEB)

Keuken, M.; Voogt, M.; Moerman, M. [TNO, Utrecht (Netherlands); Blom, M.; Weijers, E.P. [Energy research Centre of the Netherlands ECN, Petten (Netherlands); Roeckmann, T.; Dusek, U. [Institute for Marine and Atmospheric Research IMAU, Utrecht (Netherlands)

2013-06-15

The contribution of regional, urban and traffic sources to PM{sub 2.5} and PM{sub 10} in an urban area was investigated in this study. The chemical composition of PM{sub 2.5} and PM{sub 10} was measured over a year at a street location and up- and down-wind of the city of Rotterdam, Netherlands. The {sup 14}C content in EC and OC concentrations was also determined, to distinguish the contribution from 'modern' carbon (e.g., biogenic emissions, biomass burning and wildfires) and fossil fuel combustion. It was concluded that the urban background of PM{sub 2.5} and PM{sub 10} is dominated by the regional background, and that primary and secondary PM emission by urban sources contribute less than 15%. The {sup 14}C analysis revealed that 70% of OC originates from modern carbon and 30% from fossil fuel combustion. The corresponding percentages for EC are, respectively 17% and 83%. It is concluded that in particular the urban population living in street canyons with intense road traffic has potential health risks. This is due to exposure to elevated concentrations of a factor two for EC from exhaust emissions in PM{sub 2.5} and a factor 2-3 for heavy metals from brake and tyre wear, and re-suspended road dust in PM{sub 10}. It follows that local air quality management may focus on local measures to street canyons with intense road traffic.

Proinflammatory effects and oxidative stress within human bronchial epithelial cells exposed to atmospheric particulate matter (PM2.5 and PM>2.5) collected from Cotonou, Benin

International Nuclear Information System (INIS)

Cachon, Boris Fresnel; Firmin, Stéphane; Verdin, Anthony; Ayi-Fanou, Lucie

2014-01-01

After particulate matter (PM) collection in Cotonou (Benin), a complete physicochemical characterization of PM 2.5 and PM >2.5 was led. Then, their adverse health effects were evaluated by using in vitro culture of human lung cells. BEAS-2B (bronchial epithelial cells) were intoxicated during short-term exposure at increasing PM concentrations (1.5–96 μg/cm 2 ) to determine global cytotoxicity. Hence, cells were exposed to 3 and 12 μg/cm 2 to investigate the potential biological imbalance generated by PM toxicity. Our findings showed the ability of both PM to induce oxidative stress and to cause inflammatory cytokines/chemokines gene expression and secretion. Furthermore, PM were able to induce gene expression of enzymes involved in the xenobiotic metabolism pathway. Strong correlations between gene expression of metabolizing enzymes, proinflammatory responses and cell cycle alteration were found, as well as between proinflammatory responses and cell viability. Stress oxidant parameters were highly correlated with expression and protein secretion of inflammatory mediators. Highlights: • The aim of this study was to investigate the toxic potential of collected particles. • Toxicological effects were determined by using human bronchial epithelial cells. • Both particles induced oxidative stress, proinflammatory response and cell alterations. • Metabolizing enzymes were linked to proinflammatory responses and cell alterations. • Oxidative stress was highly correlated to the proinflammatory mediators. -- This study evidences the toxic potential of African fine and coarse particulate matters on respiratory epithelial cells

Chemical characterization and source identification of PM2.5 at multiple sites in the Beijing-Tianjin-Hebei region, China

Science.gov (United States)

Huang, Xiaojuan; Liu, Zirui; Liu, Jingyun; Hu, Bo; Wen, Tianxue; Tang, Guiqian; Zhang, Junke; Wu, Fangkun; Ji, Dongsheng; Wang, Lili; Wang, Yuesi

2017-11-01

The simultaneous observation and analysis of atmospheric fine particles (PM2.5) on a regional scale is an important approach to develop control strategies for haze pollution. In this study, samples of filtered PM2.5 were collected simultaneously at three urban sites (Beijing, Tianjin, and Shijiazhuang) and at a regional background site (Xinglong) in the Beijing-Tianjin-Hebei (BTH) region from June 2014 to April 2015. The PM2.5 at the four sites was mainly comprised of organic matter, secondary inorganic ions, and mineral dust. Positive matrix factorization (PMF) demonstrated that, on an annual basis, secondary inorganic aerosol was the largest PM2.5 source in this region, accounting for 29.2-40.5 % of the PM2.5 mass at the urban sites; the second-largest PM2.5 source was motor vehicle exhaust, particularly in Beijing (24.9 %), whereas coal combustion was also a large source in Tianjin (12.4 %) and Shijiazhuang (15.5 %), with particular dominance in winter. Secondary inorganic aerosol plays a vital role in the haze process, with the exception of the spring haze in Shijiazhuang and Tianjin, for which the dust source was crucial. In addition to secondary transformations, local direct emissions (coal combustion and motor vehicle exhaust) significantly contribute to the winter haze at the urban sites. Moreover, with the aggravation of haze pollution, the OC / EC mass ratio of PM2.5 decreased considerably and the nitrate-rich secondary aerosol increased during all four seasons in Beijing, both of which indicate that local motor vehicle emissions significantly contribute to the severe haze episodes in Beijing. To assess the impacts of regional transport on haze pollution, the PMF results were further processed with backward-trajectory cluster analysis, revealing that haze pollution usually occurred when air masses originating from polluted industrial regions in the south prevailed and is characterized by high PM2.5 loadings with considerable contributions from secondary

Chemical characterization and source identification of PM2.5 at multiple sites in the Beijing–Tianjin–Hebei region, China

Directory of Open Access Journals (Sweden)

X. Huang

2017-11-01

Full Text Available The simultaneous observation and analysis of atmospheric fine particles (PM2.5 on a regional scale is an important approach to develop control strategies for haze pollution. In this study, samples of filtered PM2.5 were collected simultaneously at three urban sites (Beijing, Tianjin, and Shijiazhuang and at a regional background site (Xinglong in the Beijing–Tianjin–Hebei (BTH region from June 2014 to April 2015. The PM2.5 at the four sites was mainly comprised of organic matter, secondary inorganic ions, and mineral dust. Positive matrix factorization (PMF demonstrated that, on an annual basis, secondary inorganic aerosol was the largest PM2.5 source in this region, accounting for 29.2–40.5 % of the PM2.5 mass at the urban sites; the second-largest PM2.5 source was motor vehicle exhaust, particularly in Beijing (24.9 %, whereas coal combustion was also a large source in Tianjin (12.4 % and Shijiazhuang (15.5 %, with particular dominance in winter. Secondary inorganic aerosol plays a vital role in the haze process, with the exception of the spring haze in Shijiazhuang and Tianjin, for which the dust source was crucial. In addition to secondary transformations, local direct emissions (coal combustion and motor vehicle exhaust significantly contribute to the winter haze at the urban sites. Moreover, with the aggravation of haze pollution, the OC ∕ EC mass ratio of PM2.5 decreased considerably and the nitrate-rich secondary aerosol increased during all four seasons in Beijing, both of which indicate that local motor vehicle emissions significantly contribute to the severe haze episodes in Beijing. To assess the impacts of regional transport on haze pollution, the PMF results were further processed with backward-trajectory cluster analysis, revealing that haze pollution usually occurred when air masses originating from polluted industrial regions in the south prevailed and is characterized by high PM2.5 loadings with considerable

Carbonaceous material in fine particulate matter (PM10) of urban areas

International Nuclear Information System (INIS)

Brocco, Domenico; Leonardi, Vittorio; Maso; Marco; Prignani, Patrizia

2006-01-01

Total carbon (TC), elemental carbon (EC) and organic carbon (OC) in the fine particulate matter (PM10) were measured in the urban areas of Rome and Marino (Castelli Romani) by means a thermal method with a non-dispersive infrared detector (NDIR). The results showed that carbonaceous material constitutes 30-40% of the total aerosols in Rome and about 20% in Marino [it

Local and regional sources of fine and coarse particulate matter based on traffic and background monitoring

Science.gov (United States)

Dimitriou, Konstantinos; Kassomenos, Pavlos

2014-05-01

The aim of this study was to identify local and exogenous sources affecting particulate matter (PM) levels in five major cities of Northern Europe namely: London, Paris, Hamburg, Copenhagen and Stockholm. Besides local emissions, PM profile at urban and suburban areas of the European Union (EU) is also influenced by regional PM sources due to atmospheric transport, thus geographical city distribution is of a great importance. At each city, PM10, PM2.5, NO2, SO2, CO and O3 air pollution data from two air pollution monitoring stations of the EU network were used. Different background characteristics of the selected two sampling sites at each city facilitated comparisons, providing a more exact analysis of PM sources. Four source apportionment methods: Pearson correlations among the levels of particulates and gaseous pollutants, characterisation of primal component analysis components, long-range transport analysis and extrapolation of PM size distribution ratios were applied. In general, fine (PM2.5) and coarse (PM10) particles were highly correlated, thus common sources are suggested. Combustion-originated gaseous pollutants (CO, NO2, SO2) were strongly associated to PM10 and PM2.5, primarily at areas severely affected by traffic. On the contrary, at background stations neighbouring important natural sources of particles or situated in suburban areas with rural background, natural emissions of aerosols were indicated. Series of daily PM2.5/PM10 ratios showed that minimum fraction values were detected during warm periods, due to higher volumes of airborne biogenic PM coarse, mainly at stations with important natural sources of particles in their vicinity. Hybrid single-particle Lagrangian integrated trajectory model was used, in order to extract 4-day backward air mass trajectories that arrived in the five cities which are under study during days with recorded PM10 exceedances. At all five cities, a significantly large fraction of those trajectories were classified

Local PM10 and PM2.5 emission inventories from agricultural tillage and harvest in northeastern China.

Science.gov (United States)

Chen, Weiwei; Tong, Daniel Q; Zhang, Shichun; Zhang, Xuelei; Zhao, Hongmei

2017-07-01

Mineral particles or particulate matters (PMs) emitted during agricultural activities are major recurring sources of atmospheric aerosol loading. However, precise PM inventory from agricultural tillage and harvest in agricultural regions is challenged by infrequent local emission factor (EF) measurements. To understand PM emissions from these practices in northeastern China, we measured EFs of PM 10 and PM 2.5 from three field operations (i.e., tilling, planting and harvesting) in major crop production (i.e., corn and soybean), using portable real-time PM analyzers and weather station data. County-level PM 10 and PM 2.5 emissions from agricultural tillage and harvest were estimated, based on local EFs, crop areas and crop calendars. The EFs averaged (107±27), (17±5) and 26mg/m 2 for field tilling, planting and harvesting under relatively dry conditions (i.e., soil moisture agricultural dust emissions to regional air quality in northeastern China. Copyright © 2016. Published by Elsevier B.V.

Spatial and temporal characteristics of PM2.5 and source apportionment in Wuhan

Science.gov (United States)

Hao, Hanzhou; Guo, Qianqian

2018-02-01

In order to study the pollution characteristics and sources of PM2.5, the PM2.5 in Wuhan atmosphere was sampled continuously. Inductively coupled plasma mass spectrometry (ICP-MS) were employed to measure Na, K, Mg, Ca, Al, Mn, Cu, Zn, As, Pb, Cr, Ni, Co, Cd, Fe, V, Ti, Hg, Si, while water soluble ions (Cl-, NO3-, SO4 2-) as well as carbonaceous mass (EC and OC) were analyzed using ion chromatograph(IC) and carbon analyzer, respectively. The results show: (1) In 2014 and 2015, Wuhan PM2.5 values were 81.4μg/m3and 69.2μg/m3 respectively far exceed the national standard level 2, i.e. annual average 35 μg/m3 in China, annual average limit 10 μg/m3 by the World Health Organization, the annual limit of 15 μg/m3 in the United States. (2) Taking Huaqiao and Qihao as research points, the Spring Festival effect of PM2.5 in Wuhan city is analyzed. It shows that the concentration of PM2.5 in 2014 and 2015 is before Spring Festival> during Spring Festival> after Spring Festival. As a backdrop, during the Spring Festival, Qihao PM2.5 concentration than Huaqiao average low 20 μg/m3. (3) The results of positive factor matrix factorization (PMF) analysis show that PM2.5 in Summer in Wuhan mainly comes from the automobile source, soil dust source, biomass combustion, industrial source, secondary aerosol source, combustion coal source, the contribution rate is 37.7%. 25%, 16.4%, 8.1%, 6.5%,6.4%, respectively.

Seasonal characteristics, formation mechanisms and source origins of PM2.5 in two megacities in Sichuan Basin, China

Directory of Open Access Journals (Sweden)

H. Wang

2018-01-01

Full Text Available To investigate the characteristics of PM2.5 and its major chemical components, formation mechanisms, and geographical origins in the two megacities, Chengdu (CD and Chongqing (CQ, in Sichuan Basin of southwest China, daily PM2.5 samples were collected simultaneously at one urban site in each city for four consecutive seasons from autumn 2014 to summer 2015. Annual mean concentrations of PM2.5 were 67.0 ± 43.4 and 70.9 ± 41.4 µg m−3 at CD and CQ, respectively. Secondary inorganic aerosol (SNA and organic matter (OM accounted for 41.1 and 26.1 % of PM2.5 mass at CD, and 37.4 and 29.6 % at CQ, respectively. Seasonal variations of PM2.5 and major chemical components were significant, usually with the highest mass concentration in winter and the lowest in summer. Daily PM2.5 concentration exceeded the national air quality standard on 30 % of the sampling days at both sites, and most of the pollution events were at the regional scale within the basin formed under stagnant meteorological conditions. The concentrations of carbonaceous components were higher at CQ than CD, likely partially caused by emissions from the large number of motorcycles and the spraying processes used during automobile production in CQ. Heterogeneous reactions probably played an important role in the formation of SO42−, while both homogeneous and heterogeneous reactions contributed to the formation of NO3−. Geographical origins of emissions sources contributing to high PM2.5 masses at both sites were identified to be mainly distributed within the basin based on potential source contribution function (PSCF analysis.

Temporal and spatial analyses of particulate matter (PM10 and PM2.5) and its relationship with meteorological parameters over an urban city in northeast China

Science.gov (United States)

Li, Xiaolan; Ma, Yanjun; Wang, Yangfeng; Liu, Ningwei; Hong, Ye

2017-12-01

Temporal and spatial characteristics of atmospheric particulate matter (PM10 and PM2.5) and its relationship with meteorology over Shenyang, a city in northeast China, were statistically analyzed using hourly and daily averaged PM mass concentrations measured at 11 locations and surface meteorological parameters, from January 2014 to May 2016. Using averaged data from 11 stations in Shenyang, it was found that the monthly mean PM2.5 mass concentrations were higher in winter (97.2 ± 11.2 μg m- 3) and autumn (85.5 ± 42.9 μg m- 3), and lower in spring (62.0 ± 14.0 μg m- 3) and summer (42.5 ± 8.4 μg m- 3), similar to the seasonal variation in PM10 concentrations. The monthly ratios of PM2.5/PM10 ranged from 0.41 to 0.87, and were larger in autumn and winter but lowest in spring due to dust activities. PM pollution was concentrated mainly in the central, northern, and western areas of Shenyang in most seasons mainly due to anthropogenic activities such as traffic and residential emission and construction activity as well as natural dust emission. PM concentrations observed over different areas in all seasons generally exhibited two peaks, at 08:00-10:00 local time (LT) and 21:00-23:00 LT, with the exception of PM2.5 in summer, which showed only one peak during the daytime. In addition, PM10 concentrations peaked around 14:00 LT during spring in the western area of Shenyang because of strong thermal and dynamic turbulence, resulting in elevated dust emissions from adjacent dust sources. The relationship between daily PM concentrations and meteorological parameters showed both seasonal and annual variation. Overall, both PM2.5 and PM10 concentrations were negatively correlated with atmospheric visibility, with correlation coefficients (R) of 0.71 and 0.56, respectively. In most seasons, PM concentrations also exhibited negative correlations with wind speed, but showed positive correlations with air pressure, air temperature, and relative humidity. Strong wind

Deconvoluting Mixtures ofEmissions Sources to Investigate PM2.5's Ability to Generate Reactive Oxygen Species and its Associations with Cardiorespiratory Effects

Science.gov (United States)

Weber, R. J.; Bates, J.; Abrams, J.; Verma, V.; Fang, T.; Klein, M.; Strickland, M. J.; Sarnat, S. E.; Chang, H. H.; Mulholland, J. A.; Tolbert, P. E.; Russell, A. G.

2015-12-01

It is hypothesized that fine particulate matter (PM2.5) inhalation can catalytically generate reactive oxygen species (ROS) in excess of the body's antioxidant capacity, leading to oxidative stress and ultimately adverse health. PM2.5 emissions from different sources vary widely in chemical composition, with varied effects on the body. Here, the ability of mixtures of different sources of PM2.5 to generate ROS and associations of this capability with acute health effects were investigated. A dithiothreitol (DTT) assay that integrates over different sources was used to quantify ROS generation potential of ambient water-soluble PM2.5 in Atlanta from June 2012 - June 2013. PM2.5 source impacts, estimated using the Chemical Mass Balance method with ensemble-averaged source impact profiles, were related to DTT activity using a linear regression model, which provided information on intrinsic DTT activity (i.e., toxicity) of each source. The model was then used to develop a time series of daily DTT activity over a ten-year period (1998-2010) for use in an epidemiologic study. Light-duty gasoline vehicles exhibited the highest intrinsic DTT activity, followed by biomass burning and heavy-duty diesel vehicles. Biomass burning contributed the largest fraction to total DTT activity, followed by gasoline and diesel vehicles (45%, 20% and 14%, respectively). These results suggest the importance of aged oxygenated organic aerosols and metals in ROS generation. Epidemiologic analyses found significant associations between estimated DTT activity and emergency department visits for congestive heart failure and asthma/wheezing attacks in the 5-county Atlanta area. Estimated DTT activity was the only pollutant measure out of PM2.5, O3, and PM2.5 constituents elemental carbon and organic carbon) that exhibited a significant link to congestive heart failure. In two-pollutant models, DTT activity was significantly associated with asthma/wheeze and congestive heart failure while PM2

The Effects of Bus Ridership on Airborne Particulate Matter (PM10 Concentrations

Directory of Open Access Journals (Sweden)

Jaeseok Her

2016-07-01

Full Text Available Air pollution caused by rapid urbanization and the increased use of private vehicles seriously affects citizens’ health. In order to alleviate air pollution, many cities have replaced diesel buses with compressed natural gas (CNG buses that emit less exhaust gas. Urban planning strategies such as transit-oriented development (TOD posit that reducing private vehicle use and increasing public transportation use would reduce air pollution levels. The present study examined the effects of bus ridership on airborne particulate matter (PM10 concentrations in the capital region of Korea. We interpolated the levels of PM10 from 128 air pollution monitoring stations, utilizing the Kriging method. Spatial regression models were used to estimate the impact of bus ridership on PM10 levels, controlling for physical environment attributes and socio-economic factors. The analysis identified that PM10 concentration levels tend to be lower in areas with greater bus ridership. This result implies that urban and transportation policies designed to promote public transportation may be effective strategies for reducing air pollution.

Temporal evolution of main ambient PM2. 5 sources in Santiago, Chile, from 1998 to 2012

Directory of Open Access Journals (Sweden)

F. Barraza

2017-08-01

Full Text Available The inhabitants of Santiago, Chile have been exposed to harmful levels of air pollutants for decades. The city's poor air quality is a result of steady economic growth, and stable atmospheric conditions adverse to mixing and ventilation that favor the formation of oxidants and secondary aerosols. Identifying and quantifying the sources that contribute to the ambient levels of pollutants is key for designing adequate mitigation measures. Estimating the evolution of source contributions to ambient pollution levels is also paramount to evaluating the effectiveness of pollution reduction measures that have been implemented in recent decades. Here, we quantify the main sources that have contributed to fine particulate matter (PM2. 5 between April 1998 and August 2012 in downtown Santiago by using two different source-receptor models (PMF 5.0 and UNMIX 6.0 that were applied to elemental measurements of 1243 24 h filter samples of ambient PM2.5. PMF resolved six sources that contributed to ambient PM2. 5, with UNMIX producing similar results: motor vehicles (37.3 ± 1.1 %, industrial sources (18.5 ± 1.3 %, copper smelters (14.4 ± 0.8 %, wood burning (12.3 ± 1.0 %, coastal sources (9.5 ± 0.7 % and urban dust (3.0 ± 1.2 %. Our results show that over the 15 years analyzed here, four of the resolved sources significantly decreased [95 % confidence interval]: motor vehicles 21.3 % [2.6, 36.5], industrial sources 39.3 % [28.6, 48.4], copper smelters 81.5 % [75.5, 85.9], and coastal sources 58.9 % [38.5, 72.5], while wood burning did not significantly change and urban dust increased by 72 % [48.9, 99.9]. These changes are consistent with emission reduction measures, such as improved vehicle emission standards, cleaner smelting technology, introduction of low-sulfur diesel for vehicles and natural gas for industrial processes, public transport improvements, etc. However, it is also apparent that the

Hospital indoor PM10/PM2.5 and associated trace elements in Guangzhou, China

International Nuclear Information System (INIS)

Wang Xinhua; Bi Xinhui; Sheng Guoying; Fu Jiamo

2006-01-01

PM10 and PM2.5 samples were collected in the indoor environments of four hospitals and their adjacent outdoor environments in Guangzhou, China during the summertime. The concentrations of 18 target elements in particles were also quantified. The results showed that indoor PM2.5 levels with an average of 99 μg m -3 were significantly higher than outdoor PM2.5 standard of 65 μg m -3 recommended by USEPA [United States Environmental Protection Agency. Office of Air and Radiation, Office of Air Quality Planning and Standards, Fact Sheet. EPA's Revised Particulate Matter Standards, 17, July 1997] and PM2.5 constituted a large fraction of indoor respirable particles (PM10) by an average of 78% in four hospitals. High correlation between PM2.5 and PM10 (R 2 of 0.87 for indoors and 0.90 for outdoors) suggested that PM2.5 and PM10 came from similar particulate emission sources. The indoor particulate levels were correlated with the corresponding outdoors (R 2 of 0.78 for PM2.5 and 0.67 for PM10), demonstrating that outdoor infiltration could lead to direct transportation into indoors. In addition to outdoor infiltration, human activities and ventilation types could also influence indoor particulate levels in four hospitals. Total target elements accounted for 3.18-5.56% of PM2.5 and 4.38-9.20% of PM10 by mass, respectively. Na, Al, Ca, Fe, Mg, Mn and Ti were found in the coarse particles, while K, V, Cr, Ni, Cu, Zn, Cd, Sn, Pb, As and Se existed more in the fine particles. The average indoor concentrations of total elements were lower than those measured outdoors, suggesting that indoor elements originated mainly from outdoor emission sources. Enrichment factors (EF) for trace element were calculated to show that elements of anthropogenic origins (Zn, Pb, As, Se, V, Ni, Cu and Cd) were highly enriched with respect to crustal composition (Al, Fe, Ca, Ti and Mn). Factor analysis was used to identify possible pollution source-types, namely street dust, road traffic and

Hospital indoor PM10/PM2.5 and associated trace elements in Guangzhou, China.

Science.gov (United States)

Wang, Xinhua; Bi, Xinhui; Sheng, Guoying; Fu, Jiamo

2006-07-31

PM10 and PM2.5 samples were collected in the indoor environments of four hospitals and their adjacent outdoor environments in Guangzhou, China during the summertime. The concentrations of 18 target elements in particles were also quantified. The results showed that indoor PM2.5 levels with an average of 99 microg m(-3) were significantly higher than outdoor PM2.5 standard of 65 microg m(-3) recommended by USEPA [United States Environmental Protection Agency. Office of Air and Radiation, Office of Air Quality Planning and Standards, Fact Sheet. EPA's Revised Particulate Matter Standards, 17, July 1997] and PM2.5 constituted a large fraction of indoor respirable particles (PM10) by an average of 78% in four hospitals. High correlation between PM2.5 and PM10 (R(2) of 0.87 for indoors and 0.90 for outdoors) suggested that PM2.5 and PM10 came from similar particulate emission sources. The indoor particulate levels were correlated with the corresponding outdoors (R(2) of 0.78 for PM2.5 and 0.67 for PM10), demonstrating that outdoor infiltration could lead to direct transportation into indoors. In addition to outdoor infiltration, human activities and ventilation types could also influence indoor particulate levels in four hospitals. Total target elements accounted for 3.18-5.56% of PM2.5 and 4.38-9.20% of PM10 by mass, respectively. Na, Al, Ca, Fe, Mg, Mn and Ti were found in the coarse particles, while K, V, Cr, Ni, Cu, Zn, Cd, Sn, Pb, As and Se existed more in the fine particles. The average indoor concentrations of total elements were lower than those measured outdoors, suggesting that indoor elements originated mainly from outdoor emission sources. Enrichment factors (EF) for trace element were calculated to show that elements of anthropogenic origins (Zn, Pb, As, Se, V, Ni, Cu and Cd) were highly enriched with respect to crustal composition (Al, Fe, Ca, Ti and Mn). Factor analysis was used to identify possible pollution source-types, namely street dust, road traffic

Particle Reduction Strategies - PAREST. PM10-cause analysis based on hypothetical emissions scenarios. Sub-report; Strategien zur Verminderung der Feinstaubbelastung - PAREST. PM10-Ursachenanalyse auf der Basis hypothetischer Emissionsszenarien. Teilbericht

Energy Technology Data Exchange (ETDEWEB)

Stern, Rainer [Freie Univ. Berlin (Germany). Inst. fuer Meteorologie, Troposphaerische Umweltforschung

2013-06-15

In this report, a PM10 cause analysis is presented, which provides an estimation of the extent to which the emitted substances from ten different source sectors are responsible for the calculated PM10 concentrations in Germany (PM = particulate matter). [German] In diesem Bericht wird eine PM10-Ursachenanalyse vorgestellt, die eine Abschaetzung liefert, in welchem Umfang die in Deutschland von den verschiedenen Verursachergruppen emittierten Stoffe fuer die in Deutschland berechneten PM10-Konzentrationen verantwortlich sind.

Fine particulate matter in the tropical environment: monsoonal effects, source apportionment, and health risk assessment

Directory of Open Access Journals (Sweden)

M. F. Khan

2016-01-01

Full Text Available The health implications of PM2.5 in the tropical region of Southeast Asia (SEA are significant as PM2.5 can pose serious health concerns. PM2.5 concentration and sources here are strongly influenced by changes in the monsoon regime from the south-west quadrant to the north-east quadrant in the region. In this work, PM2.5 samples were collected at a semi-urban area using a high-volume air sampler at different seasons on 24 h basis. Analysis of trace elements and water-soluble ions was performed using inductively coupled plasma mass spectroscopy (ICP-MS and ion chromatography (IC, respectively. Apportionment analysis of PM2.5 was carried out using the United States Environmental Protection Agency (US EPA positive matrix factorization (PMF 5.0 and a mass closure model. We quantitatively characterized the health risks posed to human populations through the inhalation of selected heavy metals in PM2.5. 48 % of the samples collected exceeded the World Health Organization (WHO 24 h PM2.5 guideline but only 19 % of the samples exceeded 24 h US EPA National Ambient Air Quality Standard (NAAQS. The PM2.5 concentration was slightly higher during the north-east monsoon compared to south-west monsoon. The main trace metals identified were As, Pb, Cd, Ni, Mn, V, and Cr while the main ions were SO42−, NO3−, NH4+, and Na. The mass closure model identified four major sources of PM2.5 that account for 55 % of total mass balance. The four sources are mineral matter (MIN (35 %, secondary inorganic aerosol (SIA (11 %, sea salt (SS (7 %, and trace elements (TE (2 %. PMF 5.0 elucidated five potential sources: motor vehicle emissions coupled with biomass burning (31 % were the most dominant, followed by marine/sulfate aerosol (20 %, coal burning (19 %, nitrate aerosol (17 %, and mineral/road dust (13 %. The hazard quotient (HQ for four selected metals (Pb, As, Cd, and Ni in PM2.5 mass was highest in PM2.5 mass from the coal burning

Sources of PM10 Air Pollution in Rural Area in the Vicinity of a Highway In Žilina Selfgoverning Region, Slovakia

Science.gov (United States)

Jandačka, Dušan

2015-05-01

Particulate matter results as an aftermath of numerous distinctive processes in the atmosphere and they become a part of everyday life. Their harmful effect and impact on the ambient environment is determined predominantly by the presence of various chemical substances and elements. The chemical composition of these particles (organic and elemental carbon, mineral dust, sea aerosols, secondary particles, especially sulphates and nitrates, heavy metals and further elements) is mainly impacted on by their origin, whereas the primary source of the particulate matter is determined and specified by the profile of chemical elements and substances. Particulate Matter (PM) may originate in various natural resources or anthropogenic sources. Among the natural sources sea salt is to be counted on, dust of the earth crust, pollen and volcanic ashes. Anthropogenic sources do include, predominantly, burning fossil fuels in the fossil-fuel power plants, local heating of households, burning liquefied fossil fuels in the combustion engines of vehicles, noncombustion related emissions as a result of vehicular traffic, resuspension of the road-traffic-related dust.

Sources of PM10 Air Pollution in Rural Area in the Vicinity of a Highway In Žilina Selfgoverning Region, Slovakia

Directory of Open Access Journals (Sweden)

Jandačka Dušan

2015-05-01

Full Text Available Particulate matter results as an aftermath of numerous distinctive processes in the atmosphere and they become a part of everyday life. Their harmful effect and impact on the ambient environment is determined predominantly by the presence of various chemical substances and elements. The chemical composition of these particles (organic and elemental carbon, mineral dust, sea aerosols, secondary particles, especially sulphates and nitrates, heavy metals and further elements is mainly impacted on by their origin, whereas the primary source of the particulate matter is determined and specified by the profile of chemical elements and substances. Particulate Matter (PM may originate in various natural resources or anthropogenic sources. Among the natural sources sea salt is to be counted on, dust of the earth crust, pollen and volcanic ashes. Anthropogenic sources do include, predominantly, burning fossil fuels in the fossil-fuel power plants, local heating of households, burning liquefied fossil fuels in the combustion engines of vehicles, noncombustion related emissions as a result of vehicular traffic, resuspension of the road-traffic-related dust.

Análisis del origen de PM10 y PM2.5 en Bogotá usando gráficos polares (Analysis of the origin of PM10 and PM2.5 in Bogota by using polar plots

Directory of Open Access Journals (Sweden)

Pedro Alejandro García Ávila

2016-09-01

Full Text Available Determinar la procedencia de los contaminantes del aire registrados por una red de monitoreo es fundamental para diseñar acciones de prevención y control de la contaminación. Con este fin, se analizaron, mediante la aplicación Openair®, los registros de material particulado (PM10 y PM2.5, velocidad y dirección de los vientos, en 10 estaciones de monitoreo de calidad del aire en Bogotá para el período 2009-2011, encontrándose la influencia de fuentes locales y regionales. Se determinaron altas concentraciones de material particulado relacionadas con velocidades de viento superiores a 5 m/s procedentes del occidente, lo cual sugiere un transporte regional de contaminantes desde los municipios vecinos del occidente de la ciudad (Soacha, Funza, Mosquera, Madrid, hacia su centro geográfico. Estos municipios concentran actividad industrial y transporte pesado de bienes desde y hacia Bogotá. Las fuentes localizadas al interior de la ciudad, en particular aquellas que emplean carbón como combustible y las fuentes móviles que transitan sobre las vías principales, contribuyen a generar altos niveles de material particulado cuando los vientos son débiles, pero en menor magnitud que las fuentes externas. (Abstract. The design of pollution prevention strategies and plans requires information about the origin of the pollutants. In this work, particulate matter (PM10 and PM2.5, wind speed and wind direction records from 10 air quality monitoring stations in Bogota between 2009 and 2011 were analyzed using Openair®. The influence of local and regional sources was established. High concentrations of particulate matter associated with wind speeds exceeding 5 m/s from the West were found, suggesting regional transport from the neighboring municipalities of Soacha, Funza, Mosquera and Madrid, towards its geographic center. These municipalities have a significant industrial activity and heavy transport of goods to and from Bogota. Sources located

Complexity analysis in particulate matter measurements

Directory of Open Access Journals (Sweden)

Luciano Telesca

2011-09-01

Full Text Available We investigated the complex temporal fluctuations of particulate matter data recorded in London area by using the Fisher-Shannon (FS information plane. In the FS plane the PM10 and PM2.5 data are aggregated in two different clusters, characterized by different degrees of order and organization. This results could be related to different sources of the particulate matter.

Particulate matter urban air pollution from traffic car

Science.gov (United States)

Filip, G. M.; Brezoczki, V. M.

2017-05-01

The particulate matters (PM) are very important compounds of urban air pollution. There are a lot of air pollution sources who can generate PM and one of the most important of them it is urban traffic car. Air particulate matters have a major influence on human health so everywhere are looking for PM reducing solutions. It is knows that one of the solution for reduce the PM content from car traffic on ambient urban air is the fluidity of urban traffic car by introduction the roundabout intersections. This paper want to present some particulate matter determinations for PM10 and PM2.5 conducted on the two types of urban intersection respectively traffic light and roundabout intersections in Baia Mare town in the approximate the same work conditions. The determinations were carried out using a portable particulate matter monitor Haz - Dust model EPAM - 5000, who can provide a real time data for PM10, PM 2.5.Determinations put out that there are differences between the two locations regarding the PM content on ambient air. On roundabout intersection the PM content is less than traffic light intersection for both PM10 and PM 2.5 with more than 30%.

Characteristics of fine particulate matter and its sources in an industrialized coastal city, Ningbo, Yangtze River Delta, China

Science.gov (United States)

Wang, Weifeng; Yu, Jie; Cui, Yang; He, Jun; Xue, Peng; Cao, Wan; Ying, Hongmei; Gao, Wenkang; Yan, Yingchao; Hu, Bo; Xin, Jinyuan; Wang, Lili; Liu, Zirui; Sun, Yang; Ji, Dongsheng; Wang, Yuesi

2018-05-01

Chemical information is essential in understanding the characteristics of airborne particles, and effectively controlling airborne particulate matter pollution, but it remains unclear in some regions due to the scarcity of measurement data. In the present study, 92 daily PM2.5 (particulate matter with an aerodynamic diameter ≤ 2.5 μm) samples as well as historical observation data of air pollutants were collected in urban Ningbo, one of important industrial cities in the coastal area of the Yangtze River Delta, China in autumn and winter (from Nov. 2014 to Feb. 2015). Various chemical species in PM2.5 were determined including water soluble ions, organic and elemental carbon and elements. Positive matrix factorization model, cluster analysis of back trajectories, potential source contribution function (PSCF) model and concentration-weighted trajectory (CWT) model were used for identifying sources, apportioning contributions from each source and tracking potential areas of sources. The results showed the PM2.5 concentration has been reducing; nonetheless, the concentrations of PM2.5 are still much higher than the World Health Organization guideline with high PM2.5 concentrations observed in autumn and winter for the past few years. During the sampling period, the average PM2.5 mass concentration was 77 μg/m3 with the major components of OC, NO3-, SO42 -, NH4+ and EC, accounting for 24.7, 18.8, 14.5, 11.8 and 6.4% in the total mass concentration, respectively. When the aerosol pollution got worse during the sampling period, the NO3-, SO42 - and NH4+ concentrations increased accordingly and NO3- appeared to increase at fastest rate. SO42 - transported from industrial areas led to slight difference in spatial distribution of SO42 - in Ningbo. More secondary organic carbon was formed and the enrichment factor values of Cu, Ag, Cd, Sn and Pb increased with the degradation of air quality. Ten types of sources were identified for PM2.5 in the autumn and winter of

Apportionment of the sources of high fine particulate matter concentration events in a developing aerotropolis in Taoyuan, Taiwan.

Science.gov (United States)

Chuang, Ming-Tung; Chen, Yu-Chieh; Lee, Chung-Te; Cheng, Chung-Hao; Tsai, Yu-Jen; Chang, Shih-Yu; Su, Zhen-Sen

2016-07-01

To investigate the characteristics and contributions of the sources of fine particulate matter with a size of up to 2.5 μm (PM2.5) during the period when pollution events could easily occur in Taoyuan aerotropolis, Taiwan, this study conducted sampling at three-day intervals from September 2014 to January 2015. Based on the mass concentration of PM2.5, the sampling days were classified into high PM2.5 concentration event days (PM2.5>35 μg m(-3)) and non-event days (PM2.5<35 μg m(-3)). In addition, the chemical species, including water-soluble inorganic ions, carbonaceous components, and metal elements, were analyzed. The sources of pollution and their contributions were estimated using the positive matrix factorization (PMF) model. Furthermore, the effect of the weather type on the measurement results was also explored based on wind field conditions. The mass fractions of Cl(-) and NO3(-) increased when a high PM2.5 concentration event occurred, and they were also higher under local emitted conditions than under long range transported conditions, indicating that secondary nitrate aerosols were the major increasing local species that caused high PM2.5 concentration events. Seven sources of pollution could be distinguished using the PMF model on the basis of the characteristics of the species. Industrial emissions, coal combustion/urban waste incineration, and local emissions from diesel/gasoline vehicles were the main sources that contributed to pollution on high PM2.5 concentration event days. In order to reduction of high PM2.5 concentration events, the control of diesel and gasoline vehicle emission is important and should be given priority. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mass closure and source apportionment of PM2.5 by Positive Matrix Factorization analysis in urban Mediterranean environment

Science.gov (United States)

Mantas, E.; Remoundaki, E.; Halari, I.; Kassomenos, P.; Theodosi, C.; Hatzikioseyian, A.; Mihalopoulos, N.

2014-09-01

A systematic monitoring of PM2.5 was carried out during a period of three years (from February 2010 to April 2013) at an urban site, at the National Technical University of Athens campus. Two types of 24-h PM2.5 samples have been collected: 271 samples on PTFE and 116 samples on quartz filters. Daily PM2.5 concentrations were determined for both types of samples. Total sulfur, crustal origin elements and elements of a major crustal component (Al, Si, Fe, Ca, K, Mg, Ti) trace elements (Zn, Pb, Cu, Ni, P, V, Cr, Mn) and water soluble ions (Cl-, NO3-, SO42-, Na+, K+, NH4+, Ca2+, Mg2+) were determined on the PTFE samples. Organic carbon (OC), elemental carbon (EC) and water soluble ions were determined on the quartz samples. For the mass closure six components were considered: Secondary Inorganic Aerosol (SIA), Organic Matter (OM), Elemental Carbon (EC), Dust, Mineral anthropogenic component (MIN) and Sea Salt (SS). SIA and OM contributed in the mass of PM2.5 almost equally: 30-36% and 30% respectively. EC, SS and MIN accounted for 5, 4 and 3% respectively of the total PM2.5 mass. Dust accounted for about 3-5% in absence of dust transport event and reached a much higher percentage in case of dust transport event. These contributions justify at least 80% of the PM2.5 mass. Source apportionment analysis has been performed by Positive Matrix Factorization. The combination of the PMF results obtained by both data sets lead to the definition of six factors: 1. SO42-, NH4+, OC (industrial/regional sources, secondary aerosol) 2. EC, OC, K and trace metals (traffic and heating by biomass burning, locally emitted aerosol). 3. Ca, EC, OC and trace metals (urban-resuspended road dust reflecting exhaust emissions), 4. Secondary nitrates 5. Na, Cl (marine source) 6. Si, Al, Ti, Ca, Fe (Dust transported from Sahara). These factors reflect not only main sources contributions but also underline the key role of atmospheric dynamics and aerosol ageing processes in this Mediterranean

Anomalous elevated radiocarbon measurements of PM{sub 2.5}

Energy Technology Data Exchange (ETDEWEB)

Buchholz, Bruce A., E-mail: buchholz2@llnl.gov [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Fallon, Stewart J. [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Radiocarbon Dating Laboratory, Research School of Earth Sciences, Australian National University, Canberra, ACT 0200 (Australia); Zermeno, Paula; Bench, Graham [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Schichtel, Bret A. [Cooperative Institute for Research in the Atmosphere, Colorado State University, 1375 Campus Delivery, Fort Collins, CO 80523 (United States)

2013-01-15

Two-component models are often used to determine the contributions made by fossil fuel and natural sources of carbon in airborne particulate matter (PM). The models reduce thousands of actual sources to two end members based on isotopic signature. Combustion of fossil fuels produces PM free of carbon-14 ({sup 14}C). Wood or charcoal smoke, restaurant fryer emissions, and natural emissions from plants produce PM with the contemporary concentration of {sup 14}C approximately 1.2 Multiplication-Sign 10{sup -1214}C/C. Such data can be used to estimate the relative contributions of fossil fuels and biogenic aerosols to the total aerosol loading and radiocarbon analysis is becoming a popular source apportionment method. Emissions from incinerators combusting medical or biological wastes containing tracer {sup 14}C can skew the {sup 14}C/C ratio of PM, however, so critical analysis of sampling sites for possible sources of elevated PM needs to be completed prior to embarking on sampling campaigns. Results are presented for two ambient monitoring sites in different areas of the United States where {sup 14}C contamination is apparent. Our experience suggests that such contamination is uncommon but is also not rare ({approx}10%) for PM sampling sites.

Apportionment of the sources of high fine particulate matter concentration events in a developing aerotropolis in Taoyuan, Taiwan

International Nuclear Information System (INIS)

Chuang, Ming-Tung; Chen, Yu-Chieh; Lee, Chung-Te; Cheng, Chung-Hao; Tsai, Yu-Jen; Chang, Shih-Yu; Su, Zhen-Sen

2016-01-01

To investigate the characteristics and contributions of the sources of fine particulate matter with a size of up to 2.5 μm (PM 2.5 ) during the period when pollution events could easily occur in Taoyuan aerotropolis, Taiwan, this study conducted sampling at three-day intervals from September 2014 to January 2015. Based on the mass concentration of PM 2.5 , the sampling days were classified into high PM 2.5 concentration event days (PM 2.5 >35 μg m −3 ) and non-event days (PM 2.5 <35 μg m −3 ). In addition, the chemical species, including water-soluble inorganic ions, carbonaceous components, and metal elements, were analyzed. The sources of pollution and their contributions were estimated using the positive matrix factorization (PMF) model. Furthermore, the effect of the weather type on the measurement results was also explored based on wind field conditions. The mass fractions of Cl − and NO 3 − increased when a high PM 2.5 concentration event occurred, and they were also higher under local emitted conditions than under long range transported conditions, indicating that secondary nitrate aerosols were the major increasing local species that caused high PM 2.5 concentration events. Seven sources of pollution could be distinguished using the PMF model on the basis of the characteristics of the species. Industrial emissions, coal combustion/urban waste incineration, and local emissions from diesel/gasoline vehicles were the main sources that contributed to pollution on high PM 2.5 concentration event days. In order to reduction of high PM 2.5 concentration events, the control of diesel and gasoline vehicle emission is important and should be given priority. - Highlights: • The mass fractions of NH 4 + , K + , Cl − and NO 3 − increased during PM 2.5 event days. • Reduction of coal combustion/urban waste incineration emissions should be prioritized. • The control of vehicle emission is important in the locally emitted periods. • Secondary

Spatial and temporal variation of sources contributing to quasi-ultrafine particulate matter PM0.36 in Augsburg, Germany.

Science.gov (United States)

Li, Fengxia; Schnelle-Kreis, Jürgen; Cyrys, Josef; Wolf, Kathrin; Karg, Erwin; Gu, Jianwei; Orasche, Jürgen; Abbaszade, Gülcin; Peters, Annette; Zimmermann, Ralf

2018-08-01

to study the sources contributing to quasi-ultrafine particle (UFP) organic carbon and the spatial temporal variability of the sources. 24h quasi-UFP (particulate matter quasi-UFP vary among sites and source types and show source-specific characteristics. Therefore, caution should be taken when using one monitor site measurement to assess human exposure in health effect studies of quasi-UFP. Copyright © 2018 Elsevier B.V. All rights reserved.

Preparation of 147Pm ceramic source core

International Nuclear Information System (INIS)

Mielcarski, M.

1989-01-01

Preparation of ceramic pellets containing fixed promethium-147 is described. Incorporation rate of 147 Pm into the ceramic material was determined. The leachability and vaporization of promethium from the obtained ceramics was investigated. The ceramic pellets prepared by the described procedure, mounted in special holders, can be applied as point sources in beta backscatter thickness gauges. (author)

PM2.5 source apportionment with organic markers in the Southeastern Aerosol Research and Characterization (SEARCH) study.

Science.gov (United States)

Watson, John G; Chow, Judith C; Lowenthal, Douglas H; Antony Chen, L-W; Shaw, Stephanie; Edgerton, Eric S; Blanchard, Charles L

2015-09-01

Positive matrix factorization (PMF) and effective variance (EV) solutions to the chemical mass balance (CMB) were applied to PM(2.5) (particulate matter with an aerodynamic diameter thermal carbon fraction concentrations were supplemented with detailed nonpolar organic speciation by thermal desorption-gas chromatography/mass spectrometry (TD-GC/MS). Source contribution estimates were calculated for motor vehicle exhaust, biomass burning, cooking, coal-fired power plants, road dust, vegetative detritus, and secondary sulfates and nitrates for Atlanta. Similar sources were found for Birmingham, with the addition of an industrial source and the separation of biomass burning into open burning and residential wood combustion. EV-CMB results based on conventional species were qualitatively similar to those estimated by PMF-CMB. Secondary ammonium sulfate was the largest contributor, accounting for 27-38% of PM(2.5), followed by biomass burning (21-24%) and motor vehicle exhaust (9-24%) at both sites, with 4-6% of PM(2.5) attributed to coal-fired power plants by EV-CMB. Including organic compounds in the EV-CMB reduced the motor vehicle exhaust and biomass burning contributions at both sites, with a 13-23% deficit for PM(2.5) mass. The PMF-CMB solution showed mixing of sources within the derived factors, both with and without the addition of speciated organics, as is often the case with complex source mixtures such as those at these urban-scale sites. The nonpolar TD-GC/MS compounds can be obtained from existing filter samples and are a useful complement to the elements, ions, and carbon fractions. However, they should be supplemented with other methods, such as TD-GC/MS on derivitized samples, to obtain a wider range of polar compounds such as sterols, sugars, and organic acids. The PMF and EV solutions to the CMB equations are complementary to, rather than replacements for, each other, as comparisons of their results reveal uncertainties that are not otherwise evident

Characteristics and source apportionment of organic matter in PM(2.5) from cities in different climatic zones of China

Science.gov (United States)

Feng, Jialiang

For the first time, the dependency of the characteristics of organic matter in PM2.5 on geographical and climatic zones in three metropolitan cities of China was studied. Seasonal samples were collected at suburban and urban sites in Beijing, Shanghai and Guangzhou in 2002 and 2003. To further support the above study, seasonal samples were also collected at Changdao Island, a remote island, in Bohai Sea/Yellow Sea. Concentrations of organic carbon (OC), elemental carbon (EC), water-soluble organic carbon (WSOC), and solvent-extractable organic compounds (SEOC) were analyzed. The characteristics of the n-alkanes, polycyclic aromatic hydrocarbons, n-fatty acids, n-alkanols and molecular markers such as triterpanes were determined and used for source identification. Source apportionment was complemented by Chemical Mass Balance (CMB) modeling using the measured organic species as tracers. The impact of wind speed and wind direction on air quality was studied by back trajectory calculations and analysis. In general, traffic emissions were the largest contributors of OC followed by coal burning, kitchen emissions, vegetative detritus and biomass burning. However, in the space-heating season in Northern China, coal burning was the most important contributor of OC in the suburban areas of Beijing and at Changdao. Beijing had the highest concentration of organic aerosol followed by Guangzhou and Shanghai, while seasonal variation was in reverse order. Dispersion conditions determined by local topographies and meteorology were responsible for this trend. Contrary to common understanding, pollutant concentrations at the suburban sites were higher than the urban sites in all three cities. The main reason was the rapid urbanization of the suburban areas in the immediate vicinity of urban centers since China opened up for economic development, in addition, large numbers of manufacturing plants were relocated from the cities to the countryside in an attempt to clean up the urban

Anti-Inflammatory Effects of Pomegranate Peel Extract in THP-1 Cells Exposed to Particulate Matter PM10

Directory of Open Access Journals (Sweden)

Soojin Park

2016-01-01

Full Text Available Epidemiological and experimental evidence support health risks associated with the exposure to airborne particulate matter with a diameter of <10 μM (PM10. PM10 stimulates the production of reactive oxygen species (ROS and inflammatory mediators. Thus, we assumed that natural antioxidants might provide health benefits attenuating hazardous effects of PM10. In the present study, we examined the effects of pomegranate peel extract (PPE on THP-1 monocytic cells exposed to PM10. PM10 induced cytotoxicity and the production of ROS. It also increased the expression and secretion of inflammatory cytokines, such as tumor necrosis factor-α (TNF-α, interleukin-1β (IL-1β, and monocyte chemoattractant protein-1 (MCP-1, and cell adhesion molecules, such as intercellular adhesion molecule-1 (ICAM-1 and vascular cell adhesion molecule-1 (VCAM-1. PPE at 10–100 μg mL−1 attenuated the production of ROS and the expression of TNF-α, IL-1β, MCP-1, and ICAM-1, but not VCAM-1, in THP-1 cells stimulated by PM10 (100 μg mL−1. PPE also attenuated the adhesion of PM10-stimulated THP-1 cells to EA.hy926 endothelial cells. PPE constituents, punicalagin and ellagic acid, attenuated PM10-induced monocyte adhesion to endothelial cells, and punicalagin was less cytotoxic compared to ellagic acid. The present study suggests that PPE and punicalagin may be useful in alleviating inflammatory reactions due to particulate matter.

TNFα and IL-6 Responses to Particulate Matter in Vitro: Variation According to PM Size, Season, and Polycyclic Aromatic Hydrocarbon and Soil Content

Science.gov (United States)

Manzano-León, Natalia; Serrano-Lomelin, Jesús; Sánchez, Brisa N.; Quintana-Belmares, Raúl; Vega, Elizabeth; Vázquez-López, Inés; Rojas-Bracho, Leonora; López-Villegas, Maria Tania; Vadillo-Ortega, Felipe; De Vizcaya-Ruiz, Andrea; Perez, Irma Rosas; O’Neill, Marie S.; Osornio-Vargas, Alvaro R.

2015-01-01

Background: Observed seasonal differences in particulate matter (PM) associations with human health may be due to their composition and to toxicity-related seasonal interactions. Objectives: We assessed seasonality in PM composition and in vitro PM pro-inflammatory potential using multiple PM samples. Methods: We collected 90 weekly PM10 and PM2.5 samples during the rainy-warm and dry-cold seasons in five urban areas with different pollution sources. The elements, polycyclic aromatic hydrocarbons (PAHs), and endotoxins identified in the samples were subjected to principal component analysis (PCA). We tested the potential of the PM to induce tumor necrosis factor alpha (TNFα) and interleukin 6 (IL-6) secretion in cultured human monocytes (THP-1), and we modeled pro-inflammatory responses using the component scores. Results: PM composition varied by size and by season. PCA identified two main components that varied by season. Combustion-related constituents (e.g., vanadium, benzo[a]pyrene, benzo[a]anthracene) mainly comprised component 1 (C1). Soil-related constituents (e.g., endotoxins, silicon, aluminum) mainly comprised component 2 (C2). PM from the rainy-warm season was high in C2. PM (particularly PM2.5) from the dry-cold season was rich in C1. Elevated levels of cytokine production were associated with PM10 and C2 (rainy-warm season), whereas reduced levels of cytokine production were associated with PM2.5 and C1 (dry-cold season). TNFα secretion was increased following exposure to PM with high (vs. low) C2 content, but TNFα secretion in response to PM was decreased following exposure to samples containing ≥ 0.1% of C1-related PAHs, regardless of C2 content. The results of the IL-6 assays suggested more complex interactions between PM components and particle size. Conclusions: Variations in PM soil and PAH content underlie seasonal and PM size–related patterns in TNFα secretion. These results suggest that the mixture of components in PM explains some

Indoor pollution: PM2.5 and PM10 from cigarette smoke

International Nuclear Information System (INIS)

Chianese, E.; Barone, G.; Castaldo, R.M.; Riccio, A.

2009-01-01

This work is aimed to establishing the temporal and spatial dispersion of PM 10 and PM 2.5 particulate matter fractions generated by cigarettes smoking in an indoor ambient. To this purpose, PM 10 and PM 2.5 concentrations were collected with a mobile instrument positioned in a room accommodating a smoking machine. [it

Estimating PM2.5 Concentrations in Xi'an City Using a Generalized Additive Model with Multi-Source Monitoring Data.

Directory of Open Access Journals (Sweden)

Yong-Ze Song

Full Text Available Particulate matter with an aerodynamic diameter <2.5 μm (PM2.5 represents a severe environmental problem and is of negative impact on human health. Xi'an City, with a population of 6.5 million, is among the highest concentrations of PM2.5 in China. In 2013, in total, there were 191 days in Xi'an City on which PM2.5 concentrations were greater than 100 μg/m3. Recently, a few studies have explored the potential causes of high PM2.5 concentration using remote sensing data such as the MODIS aerosol optical thickness (AOT product. Linear regression is a commonly used method to find statistical relationships among PM2.5 concentrations and other pollutants, including CO, NO2, SO2, and O3, which can be indicative of emission sources. The relationships of these variables, however, are usually complicated and non-linear. Therefore, a generalized additive model (GAM is used to estimate the statistical relationships between potential variables and PM2.5 concentrations. This model contains linear functions of SO2 and CO, univariate smoothing non-linear functions of NO2, O3, AOT and temperature, and bivariate smoothing non-linear functions of location and wind variables. The model can explain 69.50% of PM2.5 concentrations, with R2 = 0.691, which improves the result of a stepwise linear regression (R2 = 0.582 by 18.73%. The two most significant variables, CO concentration and AOT, represent 20.65% and 19.54% of the deviance, respectively, while the three other gas-phase concentrations, SO2, NO2, and O3 account for 10.88% of the total deviance. These results show that in Xi'an City, the traffic and other industrial emissions are the primary source of PM2.5. Temperature, location, and wind variables also non-linearly related with PM2.5.

AIRUSE-LIFE+: a harmonized PM speciation and source apportionment in 5 Southern European cities

Science.gov (United States)

Amato, F.; Alastuey, A.; Karanasiou, A.; Lucarelli, F.; Nava, S.; Calzolai, G.; Severi, M.; Becagli, S.; Gianelle, V. L.; Colombi, C.; Alves, C.; Custódio, D.; Nunes, T.; Cerqueira, M.; Pio, C.; Eleftheriadis, K.; Diapouli, E.; Reche, C.; Minguillón, M. C.; Manousakas, M.; Maggos, T.; Vratolis, S.; Harrison, R. M.; Querol, X.

2015-09-01

The AIRUSE-LIFE+ project aims at characterising similarities and heterogeneities in PM sources and contributions in urban areas from the Southern Europe. Once the main PMx sources are identified, AIRUSE aims at developing and testing the efficiency of specific and non-specific measures to improve urban air quality. This article reports the results of the source apportionment of PM10 and PM2.5 conducted at three urban background sites (Barcelona, Florence and Milan, BCN-UB, FI-UB, MLN-UB) one sub-urban background site (Athens, ATH-SUB) and one traffic site (Porto, POR-TR). After collecting 1047 PM10 and 1116 PM2.5 24 h samples from January 2013 to February 2014 simultaneously at the 5 cities, these were analysed for the contents of OC, EC, anions, cations, major and trace elements and levoglucosan. The USEPA PMF5 receptor model was applied to these datasets in a harmonised way for each city. The sum of vehicle exhaust and non-exhaust contributes within 3.9-10.8 μg m-3 (16-32 %) to PM10 and 2.3-9.4 μg m-3 (15-36 %) to PM2.5, although a fraction of secondary nitrate is also traffic-related but could not be estimated. Important contributions arise from secondary particles (nitrate, sulphate and organics) in PM2.5 (37-82 %) but also in PM10 (40-71 %) mostly at background sites, revealing the importance of abating gaseous precursors in designing air quality plans. Biomass burning (BB) contributions vary widely, from 14-24 % of PM10 in POR-TR, MLN-UB and FI-UB, 7 % in ATH-SUB to levels increase on an annual basis by 1-9 μg m-3 due to this source. Other significant sources are: - Local dust, 7-12 % of PM10 at SUB and UB sites and 19 % at the TR site, revealing a contribution from road dust resuspension. In PM2.5 percentages decrease to 2-7 % at SUB-UB sites and 15 % at the TR site. - Industries, mainly metallurgy, contributing 4-11 % of PM10 (5-12 % in PM2.5), but only at BCN-UB, POR-TR and MLN-UB. No clear impact of industrial emissions was found in FI-UB and ATH

Spatio-temporal Variations and Source Contributions of China's Premature Deaths Attributable to Ambient PM2.5

Science.gov (United States)

Rong, X.; Wang, H.

2016-12-01

With rapid economic growth, China has witnessed increasingly frequent and severe haze and smog episodes over the past decade, posing serious health impacts to the Chinese population, especially those in densely populated city clusters. Quantifications of the spatial and temporal variations of health impacts attributed to ambient fine particulate matter (PM2.5) are not only important for designing effective strategies in mitigating the health damage of air pollution, but also provide valuable references for other developing regions in the world. In this study, we evaluated the spatial distribution of premature deaths in China between 2000 and 2014 attributed to ambient PM2.5 in accord with Global Burden of Disease (GBD) based on a high resolution population density map, satellite retrieved PM2.5 concentration, and provincial health data. An Integrated Exposure Response (IER) model was applied to analyze the premature deaths for four leading causes (ischemic heart disease (IHD), chronic obstructive pulmonary disease (COPD), lung cancer (LC), stroke) in China. The contributions of emission sources to air pollution and related mortality burdens across China were further evaluated by incorporating CMAQ model. Our results suggest that China's anthropogenic ambient PM2.5 led to 1,255,400 premature deaths in 2010, 42% higher than the level in 2000. Besides the increased PM2.5 concentration, rapid urbanization has been attracting large population migration into the more developed eastern coastal urban areas, intensifying the overall health impacts. Our analysis implies that the health burdens were exacerbated in some developing inner provinces with high population density (e.g. Henan, Anhui, Sichuan) because of the relocation of more polluting and resource-intensive industries into these regions. China's regulations on PM2.5 should not be loosened on inner provinces to avoid such national level environmental inequities, and furthermore policies should be designed to form

Hydrophobic and porous cellulose nanofibrous screen for efficient particulate matter (PM2.5) blocking

International Nuclear Information System (INIS)

Chen, Liping; Guo, Yi; Peng, Xinsheng

2017-01-01

Particulate matter (PM2.5) pollution in air seriously affects public health. However, both bulk thickness and the accumulation of PM particles typically lead to a quick decline in the air permeability and large pressure drops of the conventional air clean membranes. In this work, we choose cellulose nanofibers (CNFs, a low cost, biodegradable and sustainable material) to form a hydrophobic and porous CNF thin layer on a stainless steel screen (300 mesh with pore size of 48 µ m) through a simple filtration-assisted gelation process and subsequent polydimethylsiloxane modification. The prepared hydrophobic CNFs/stainless steel screen demonstrates highly efficient PM2.5 blocking based on size-sieving effect, fast air permeability and long-term durability under natural ventilation conditions in the relative humidity range from 45% to 93%. This technique holds great potential for indoor PM2.5 blocking under natural ventilation conditions. (paper)

Hydrophobic and porous cellulose nanofibrous screen for efficient particulate matter (PM2.5) blocking

Science.gov (United States)

Chen, Liping; Guo, Yi; Peng, Xinsheng

2017-10-01

Particulate matter (PM2.5) pollution in air seriously affects public health. However, both bulk thickness and the accumulation of PM particles typically lead to a quick decline in the air permeability and large pressure drops of the conventional air clean membranes. In this work, we choose cellulose nanofibers (CNFs, a low cost, biodegradable and sustainable material) to form a hydrophobic and porous CNF thin layer on a stainless steel screen (300 mesh with pore size of 48 µm) through a simple filtration-assisted gelation process and subsequent polydimethylsiloxane modification. The prepared hydrophobic CNFs/stainless steel screen demonstrates highly efficient PM2.5 blocking based on size-sieving effect, fast air permeability and long-term durability under natural ventilation conditions in the relative humidity range from 45% to 93%. This technique holds great potential for indoor PM2.5 blocking under natural ventilation conditions.

Two Model-Based Methods for Policy Analyses of Fine Particulate Matter Control in China: Source Apportionment and Source Sensitivity

Science.gov (United States)

Li, X.; Zhang, Y.; Zheng, B.; Zhang, Q.; He, K.

2013-12-01

Anthropogenic emissions have been controlled in recent years in China to mitigate fine particulate matter (PM2.5) pollution. Recent studies show that sulfate dioxide (SO2)-only control cannot reduce total PM2.5 levels efficiently. Other species such as nitrogen oxide, ammonia, black carbon, and organic carbon may be equally important during particular seasons. Furthermore, each species is emitted from several anthropogenic sectors (e.g., industry, power plant, transportation, residential and agriculture). On the other hand, contribution of one emission sector to PM2.5 represents contributions of all species in this sector. In this work, two model-based methods are used to identify the most influential emission sectors and areas to PM2.5. The first method is the source apportionment (SA) based on the Particulate Source Apportionment Technology (PSAT) available in the Comprehensive Air Quality Model with extensions (CAMx) driven by meteorological predictions of the Weather Research and Forecast (WRF) model. The second method is the source sensitivity (SS) based on an adjoint integration technique (AIT) available in the GEOS-Chem model. The SA method attributes simulated PM2.5 concentrations to each emission group, while the SS method calculates their sensitivity to each emission group, accounting for the non-linear relationship between PM2.5 and its precursors. Despite their differences, the complementary nature of the two methods enables a complete analysis of source-receptor relationships to support emission control policies. Our objectives are to quantify the contributions of each emission group/area to PM2.5 in the receptor areas and to intercompare results from the two methods to gain a comprehensive understanding of the role of emission sources in PM2.5 formation. The results will be compared in terms of the magnitudes and rankings of SS or SA of emitted species and emission groups/areas. GEOS-Chem with AIT is applied over East Asia at a horizontal grid

Source areas and chemical composition of fine particulate matter in the Pearl River Delta region of China

Science.gov (United States)

Hagler, G. S. W.; Bergin, M. H.; Salmon, L. G.; Yu, J. Z.; Wan, E. C. H.; Zheng, M.; Zeng, L. M.; Kiang, C. S.; Zhang, Y. H.; Lau, A. K. H.; Schauer, J. J.

Fine particulate matter (PM 2.5) was measured for 4 months during 2002-2003 at seven sites located in the rapidly developing Pearl River Delta region of China, an area encompassing the major cities of Hong Kong, Shenzhen and Guangzhou. The 4-month average fine particulate matter concentration ranged from 37 to 71 μg m -3 in Guangdong province and from 29 to 34 μg m -3 in Hong Kong. Main constituents of fine particulate mass were organic compounds (24-35% by mass) and sulfate (21-32%). With sampling sites strategically located to monitor the regional air shed patterns and urban areas, specific source-related fine particulate species (sulfate, organic mass, elemental carbon, potassium and lead) and daily surface winds were analyzed to estimate influential source locations. The impact of transport was investigated by categorizing 13 (of 20 total) sampling days by prevailing wind direction (southerly, northerly or low wind-speed mixed flow). The vicinity of Guangzhou is determined to be a major source area influencing regional concentrations of PM 2.5, with levels observed to increase by 18-34 μg m -3 (accounting for 46-56% of resulting particulate levels) at sites immediately downwind of Guangzhou. The area near Guangzhou is also observed to heavily impact downwind concentrations of lead. Potassium levels, related to biomass burning, appear to be controlled by sources in the northern part of the Pearl River Delta, near rural Conghua and urban Guangzhou. Guangzhou appears to contribute 5-6 μg m -3 of sulfate to downwind locations. Guangzhou also stands out as a significant regional source of organic mass (OM), adding 8.5-14.5 μg m -3 to downwind concentrations. Elemental carbon is observed to be strongly influenced by local sources, with highest levels found in urban regions. In addition, it appears that sources outside of the Pearl River Delta contribute a significant fraction of overall fine particulate matter in Hong Kong and Guangdong province. This is evident

Partitioning of magnetic particles in PM10, PM2.5 and PM1 aerosols in the urban atmosphere of Barcelona (Spain)

International Nuclear Information System (INIS)

Revuelta, María Aránzazu; McIntosh, Gregg; Pey, Jorge; Pérez, Noemi; Querol, Xavier; Alastuey, Andrés

2014-01-01

A combined magnetic-chemical study of 15 daily, simultaneous PM 10 –PM 2.5 –PM 1 urban background aerosol samples has been carried out. The magnetic properties are dominated by non-stoichiometric magnetite, with highest concentrations seen in PM 10 . Low temperature magnetic analyses showed that the superparamagnetic fraction is more abundant when coarse, multidomain particles are present, confirming that they may occur as an oxidized outer shell around coarser grains. A strong association of the magnetic parameters with a vehicular PM 10 source has been identified. Strong correlations found with Cu and Sb suggests that this association is related to brake abrasion emissions rather than exhaust emissions. For PM 1 the magnetic remanence parameters are more strongly associated with crustal sources. Two crustal sources are identified in PM 1 , one of which is of North African origin. The magnetic particles are related to this source and so may be used to distinguish North African dust from other sources in PM 1 . - Highlights: • Magnetic properties of PM 10 , PM 2.5 and PM 1 defined for a Mediterranean urban site. • Vehicular source of magnetic particles dominates in PM 10 . • Crustal source of magnetic particles dominates in PM 1 . • Magnetic remanence may distinguish between North African and regional dust in PM 1 . - Capsule abstract two sources of magnetic atmospheric particles have been identified in Barcelona, a vehicular source which dominates in PM 10 and a crustal source that dominates in PM 1

Properties and cellular effects of particulate matter from direct emissions and ambient sources.

Science.gov (United States)

Jin, Wenjie; Su, Shu; Wang, Bin; Zhu, Xi; Chen, Yilin; Shen, Guofeng; Liu, Junfeng; Cheng, Hefa; Wang, Xilong; Wu, Shuiping; Zeng, Eddy; Xing, Baoshan; Tao, Shu

2016-10-14

The pollution of particulate matter (PM) is of great concern in China and many other developing countries. It is generally recognized that the toxicity of PM is source and property dependent. However, the relationship between PM properties and toxicity is still not well understood. In this study, PM samples from direct emissions of wood, straw, coal, diesel combustion, cigarette smoking and ambient air were collected and characterized for their physicochemical properties. Their expression of intracellular reactive oxygen species (ROS) and levels of inflammatory cytokines (i.e., tumor necrosis factor-α (TNF-α)) was measured using a RAW264.7 cell model. Our results demonstrated that the properties of the samples from different origins exhibited remarkable differences. Significant increases in ROS were observed when the cells were exposed to PMs from biomass origins, including wood, straw and cigarettes, while increases in TNF-α were found for all the samples, particularly those from ambient air. The most important factor associated with ROS generation was the presence of water-soluble organic carbon, which was extremely abundant in the samples that directly resulted from biomass combustion. Metals, endotoxins and PM size were the most important properties associated with increases in TNF-α expression levels. The association of the origins of PM particles and physicochemical properties with cytotoxic properties is illustrated using a cluster analysis.

Influences of natural emission sources (wildfires and Saharan dust) on the urban organic aerosol in Barcelona (Western Mediterranean Basis) during a PM event.

Science.gov (United States)

van Drooge, Barend L; Lopez, Jordi F; Grimalt, Joan O

2012-11-01

The urban air quality in Barcelona in the Western Mediterranean Basin is characterized by overall high particulate matter (PM) concentrations, due to intensive local anthropogenic emissions and specific meteorological conditions. Moreover, on several days, especially in summer, natural PM sources, such as long-range transported Saharan dust from Northern Africa or wildfires on the Iberian Peninsula and around the Mediterranean Basin, may influence the levels and composition of the organic aerosol. In the second half of July 2009, daily collected PM(10) filter samples in an urban background site in Barcelona were analyzed on organic tracer compounds representing several emission sources. During this period, an important PM peak event was observed. Individual organic compound concentrations increased two to five times during this event. Although highest increase was observed for the organic tracer of biomass burning, the contribution to the organic aerosol was estimated to be around 6 %. Organic tracers that could be related to Saharan dust showed no correlation with the PM and OC levels, while this was the case for those related to fossil fuel combustion from traffic emissions. Moreover, a change in the meteorological conditions gave way to an overall increase of the urban background contamination. Long-range atmospheric transport of organic compounds from primary emissions sources (i.e., wildfires and Saharan dust) has a relatively moderate impact on the organic aerosol in an urban area where the local emissions are dominating.

Ambient air quality of karachi city as reflected by atmospheric particulate matter (PM/sub 10/) concentrations

International Nuclear Information System (INIS)

Hashmi, D.R.; Shareef, A.

2016-01-01

The present study examines the variation of ambient aerosol (PM/sub 10/) concentrations in Karachi, city. Samples were collected from ten different locations, representative of urban background, residential, traffic and industrial areas from 2007 to 2011. At each location, PM/sub 10/) was measured continuously from 08:00 am to 06:00 pm at local time. The maximum 10 h average particulate matter (PM/sub 10/) mass concentrations were found at Tibet Centre (440.1 mg/m/sup 3/) and minimum at PCSIR Campus (21.7 mg/m/sup 3/) during 2008. A rising trend during 2008 may be due to the civil works for bridges and extension of roads at different locations in Karachi. The results also suggest that urban traffic and industrial areas appeared to have higher PM/sub 10/) concentration than residential and background areas. (author)

Development of a {sup 147}Pm source for beta-backscatter thickness gauge applications

Energy Technology Data Exchange (ETDEWEB)

Kumar, Manoj; Udhayakumar, J. [Radiopharmaceuticals Division, Bhabha Atomic Research Center, Radiological Laboratory, Trombay, Mumbai 400 085 (India); Nuwad, J.; Shukla, Rakesh; Pillai, C.G.S. [Chemistry Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India); Dash, Ashutosh, E-mail: adash@barc.gov.i [Radiopharmaceuticals Division, Bhabha Atomic Research Center, Radiological Laboratory, Trombay, Mumbai 400 085 (India); Venkatesh, Meera [Radiopharmaceuticals Division, Bhabha Atomic Research Center, Radiological Laboratory, Trombay, Mumbai 400 085 (India)

2011-03-15

This paper describes a method for the preparation of {sup 147}Pm sources, utilized in the determination of graphite coating thickness on the inner surface of the zircaloy cladding tube of nuclear fuels. {sup 147}Pm was adsorbed on a limited surface area [1.5 mm ({phi})x2 mm (l)] of a cylindrical aluminum rod [1.5 mm ({phi})x10 mm (l)]. In brief, the selected tip area [1.5 mm ({phi})x2 mm (l)] was anodized at a current density of 15 mA/cm{sup 2} at 15 {sup o}C in 3 M.H{sub 2}SO{sub 4} for 2 h followed by immersion of this area in 10 {mu}L of {sup 147}Pm solution containing 37 MBq (1 mCi) of activity at pH 6.0 for 24 h. The radioactive area was subsequently covered with a thin layer of Polymethyl Methacrylate (PMMA) to prevent leaching of {sup 147}Pm from the source. The quantity of incorporated {sup 147}Pm activity was assayed in a calibrated ion chamber. Quality control tests were carried out to ensure nonleachability, uniform distribution of activity and stability of the sources.

Human health risk due to variations in PM10-PM2.5 and associated PAHs levels

Science.gov (United States)

Sosa, Beatriz S.; Porta, Andrés; Colman Lerner, Jorge Esteban; Banda Noriega, Roxana; Massolo, Laura

2017-07-01

WHO (2012) reports that chronic exposure to air pollutants, including particulate matter (PM), causes the death of 7 million people, constituting the most important environmental risk for health in the world. IARC classifies contaminated outdoor air as carcinogenic, Group 1 category. However, in our countries there are few studies regarding air pollution levels and possible associated effects on public health. The current study determined PM and associated polycyclic aromatic hydrocarbons (PAHs) levels in outdoor air, identified their possible emission sources and analysed health risks in the city of Tandil (Argentina). PM10 and PM2.5 samples were collected using a low volume sampler (MiniVol TAS) in three areas: city centre, industrial and residential. Concentrations were determined by gravimetric methods and the content of the US EPA 16 priority PAHs was found by high performance liquid chromatography (HPLC). Description of the main emission sources and selection of monitoring sites resulted from spatial analysis and the IVE (International Vehicle Emissions) model was used in the characterisation of the traffic flow. Median values of 35.7 μgm-3 and 9.6 μgm-3 in PM10 and PM2.5 respectively and characteristic profiles were found for each area. Local values PAHs associated to PM10 and PM2.5, in general, were lower than 10ngm-3. The estimated Unit Risk for the three areas exceeds US EPA standards (9 × 10-5). The number of deaths attributable to short term exposure to outdoor PM10 was 4 cases in children under 5 years of age, and 21 cases in total population, for a relative risk of 1.037.

Weekly cycle of magnetic characteristics of PM2.5 and PM2.5-10 in Beijing, China

Science.gov (United States)

SHI, M.; Wu, H.; Zhang, S.; Li, H.; Yang, T.

2013-12-01

In urban areas,fine particle matter with aerodynamic diameter between 2.5 um and 10 um (PM2.5-10), and 2.5 um (PM2.5), as an important source of urban particulate matter (PM) pollutants, have significant negative effects on health, atmospheric visibility and climate. PM has increasingly become a significant index of indicating the atmospheric pollution of city. In recent years, Beijing, China has been listed as one of the most serious air pollution city in the world. In order to investigate the sources of air pollutants, a total of 283 pairs of PM2.5 and PM2.5-10 samples were collected daily from July, 2010 to June, 2011 in Beijing. Mineral magnetic properties and Scanning electron microscope (SEM) observations and energy dispersive X-ray spectroscopy (EDS) analyses of PM2.5 and PM2.5-10 were measured to verify the magnetic materials. Magnetic measures for PM indicated that the major magnetic phase was coarse-grained magnetite-like material. The χlf, χarm, SIRM and χarm/SIRM series of the PM2.5 and PM2.5-10 show seasonal dependences: high values in winter and low values in summer. In additional the parameters analyzed by Time-series methods show a strong cycle about 7 days above 95% confidence level. Weekly cycle of magnetic characteristics of PM2.5 and PM2.5-10 show different pattern: the concentration of magnetic particles in PM2.5-10 show high values in mid-week, and particle sizes is steady, while the concentration of magnetic particles in PM2.5 show reverse a weekly cycle pattern, and particle sizes is smaller in the mid-week.Microscopy analyses reveal basically three morphologies of magnetic grains: aggregate, spherules and angular particles. The ultrafine carbonaceous particles which tend to form complex clusters and chain-like structures, most likely come from coal burning and motor vehicle exhaust. Spherical particles in PM2.5 are dominantly composed of Fe, O and C, grain-diameters of particles range from 0.3 to 2 um. Angular particles of Fe

The variability in iron speciation in size fractionated residual oil fly ash particulate matter (ROFA PM).

Science.gov (United States)

Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P

2016-08-15

Ambient particulate matter (PM) containing iron can catalyze Fenton reaction leading to the production of reactive oxygen species in cells. It can also catalyze atmospheric redox reaction. These reactions are governed by the physicochemical characteristics of iron in ambient PM. As a surrogate for ambient PM, we prepared residual oil fly ash PM (ROFA PM) in a practical fire tube boiler firing residual oils with varying sulfur and ash contents. The ROFA particles were resolved into fine PM or PM2.5 (aerodynamic diameter (AD)iron speciation in PM2.5+ was ascertained using X-ray absorption spectroscopy and leaching method while that in PM2.5 was reported earlier. The results of both studies are compared to get an insight into the variability in the iron speciation in different size fractions. The results show the predominance of ferric sulfate, with a minor spinal ferrite in both PM (i.e. ZnxNi1-xFe2O4 in PM2.5, ZnFe2O4 in PM2.5+). The iron solubility in ROFA PM depends on its speciation, mode of incorporation of iron into particle's carbonaceous matrix, the grade and composition of oils, and pH of the medium. The soluble fraction of iron in PM is critical in assessing its interaction with the biological systems and its toxic potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Particulate matter 2.5 (PM2.5) personal exposure evaluation on mechanics and administrative officers at the motor vehicle testing center at Pulo Gadung, DKI Jakarta.

Science.gov (United States)

Rizky, Zuly Prima; Yolla, Patricia Bebby; Ramdhan, Doni Hikmat

2016-03-01

Exposure to fine particulate matter (PM2.5) in both the short and long term has been known to cause deaths and health effects, especially related to the heart, blood vessels, and lungs. Based on this information, researchers conducted this study at a motor vehicle testing center unit at Pulo Gadung, in Jarkarta, to determine the concentration of PM2.5 that workers were exposed to. The major source of PM2.5 in this area is from the exhaust of gas emissions from motor vehicles, which is one of the largest contributors to the levels of PM in urban areas. Ten mechanics were picked from 16 mechanics that work in this station. Four administration workers from different posts were also picked to participate. The researcher conducted the PM2.5 personal exposure measurement during weekdays from 6 to 14 April 2015 (2 workers/day). This research was conducted to measure the particle number concentration with size Organization Air Quality Guidelines, the PM2.5 exposure of the mechanics and administrative officers exceeded the recommended exposure (25 μm/m3).

Characterizing and sourcing ambient PM2.5 over key emission regions in China I: Water-soluble ions and carbonaceous fractions

Science.gov (United States)

Zhou, Jiabin; Xing, Zhenyu; Deng, Junjun; Du, Ke

2016-06-01

During the past decade, huge research resources have been devoted into studies of air pollution in China, which generated abundant datasets on emissions and pollution characterization. Due to the complex nature of air pollution as well as the limitations of each individual investigating approach, the published results were sometimes perplexing and even contradicting. This research adopted a multi-method approach to investigate region-specific air pollution characteristics and sources in China, results obtained using different analytical and receptor modeling methods were inter-compared for validation and interpretation. A year-round campaign was completed for comprehensive characterization of PM2.5 over four key emission regions: Beijing-Tianjin-Hebei (BTH), Yangzi River Delta (YRD), Pearl River Delta (PRD), and Sichuan Basin (SB). Atmospheric PM2.5 samples were collected from 10/2012 to 08/2013 at four regional sites, located on the diffusion paths of air masses from their corresponding megacities (i.e., Beijing, Shanghai, Guangzhou, and Chengdu). The annual average PM2.5 mass concentrations showed distinct regional difference, with the highest observed at BTH and lowest at PRD site. Nine water-soluble ions together contributed 33-41% of PM2.5 mass, with three dominant ionic species being SO42-, NO3-, NH4+, and carbonaceous particulate matter contributed 16-23% of PM2.5 mass. This implied that combustion and secondary formation were the main sources for PM2.5 in China. In addition, SO42-, NO3-, NH4+, and carbonaceous components (OC, EC) showed clear seasonal patterns with the highest concentration occurring in winter while the lowest in summer. Principal component analysis performed on aerosol data revealed that vehicular emissions, coal/biomass combustion, industry source, soil dust as well as secondary formation were the main potential sources for the ionic components of PM2.5. The characteristic chemical species combined with back trajectory analysis indicated

Size distribution and source identification of total suspended particulate matter and associated heavy metals in the urban atmosphere of Delhi.

Science.gov (United States)

Srivastava, Arun; Jain, V K

2007-06-01

A study of the atmospheric particulate size distribution of total suspended particulate matter (TSPM) and associated heavy metal concentrations has been carried out for the city of Delhi. Urban particles were collected using a five-stage impactor at six sites in three different seasons, viz. winter, summer and monsoon in the year 2001. Five samples from each site in each season were collected. Each sample (filter paper) was extracted with a mixture of nitric acid, hydrochloric acid and hydrofluoric acid. The acid solutions of the samples were analysed in five-particle fractions by atomic absorption spectrometry (AAS). The impactor stage fractionation of particles shows that a major portion of TSPM concentration is in the form of PM0.7 (i.e. metal mass viz. Mn, Cr, Cd, Pb, Ni, and Fe are also concentrated in the PM0.7 mode. The only exceptions are size distributions pertaining to Cu and Ca. Though, Cu is more in PM0.7 mode, its presence in size intervals 5.4-1.6microm and 1.6-0.7microm is also significant, whilst in case of Ca there is no definite pattern in its distribution with size of particles. The average PM10.9 (i.e. Source apportionment reveals that there are two sources of TSPM and PM10.9, while three and four sources were observed for PM1.6 (i.e. <1.6microm) and PM0.7, respectively. Results of regression analyses show definite correlations between PM10.9 and other fine size fractions, suggesting PM10.9 may adequately act as a surrogate for both PM1.6 and PM0.7, while PM1.6 may adequately act as a surrogate for PM0.7.

Toward Distinguishing Woodsmoke and Diesel Exhaust in Ambient Particulate Matter

International Nuclear Information System (INIS)

Braun, A.; Huggins, F.; Kubatova, A.; Wirick, S.; Maricq, M.; Mun, B.; McDonald, J.; Kelly, K.; Shah, N.; Huffman, G.

2008-01-01

Particulate matter (PM) from biomass burning and diesel exhaust has distinct X-ray spectroscopic, carbon specific signatures, which can be employed for source apportionment. Characterization of the functional groups of a wide selection of PM samples (woodsmoke, diesel soot, urban air PM) was carried out using the soft X-ray spectroscopy capabilities at the synchrotron radiation sources in Berkeley (ALS) and Brookhaven (NSLS). The spectra reveal that diesel exhaust particulate (DEP) matter is made up from a semigraphitic solid core and soluble organic matter, predominantly with carboxylic functional groups. Woodsmoke PM has no or a less prevalent, graphitic signature, instead it contains carbon-hydroxyl groups. Using these features to apportion the carbonaceous PM in ambient samples we estimate that the relative contribution of DEP to ambient PM in an urban area such as Lexington, KY and St. Louis, MO is 7% and 13.5%, respectively. These values are comparable to dispersion modeling data from nonurban and urban areas in California, and with elemental carbon measurements in urban locations such as Boston, MA, Rochester, NY, and Washington, DC.

Characterization and Aerosol Mass balance of PM2.5 and PM10 Collected in Conakry, Guinea during the 2004 Harmattan Period

Science.gov (United States)

The United States EPA conducted a six week air quality survey of the city of Conakry, Guinea, West Africa in 2004. The study was conducted to assess the background levels of anthropogenic and natural particulate matter (PM) and to investigate the local and regional sources of tho...

Growth, extracellular alkaline phosphatase activity, and kinetic characteristic responses of the bloom-forming toxic cyanobacterium, Microcystis aeruginosa, to atmospheric particulate matter (PM2.5, PM2.5-10, and PM>10).

Science.gov (United States)

Xu, Ziran; Wang, Shoubing; Wang, Yuanan; Zhang, Jie

2018-03-01

Atmospheric particulate matter (APM), commonly seen and widely excited in environment, appears great enough to influence the biochemical processes in aquatic microorganisms and phytoplankton. Understanding the response of cyanobacteria to various factors is fundamental for eutrophication control. To clarify the response of cyanobacteria to APM, the effects of PM 2.5 , PM 2.5-10 , and PM >10 on Microcystis aeruginosa were researched. Variabilities in cell density, chlorophyll a, soluble protein, malondialdehyde, extracellular activity, and kinetic parameters of alkaline phosphatase were evaluated by lab-cultured experiments. Results showed that the PM 2.5 had a slight stimulation impact on the growth and enhanced both of the 48- and 72-h extracellular alkaline phosphatase activity (APA), the affinity of alkaline phosphatase for substrate, and the 72-h maximum enzymatic reaction velocity (V max ). Moreover, the stimulations in extracellular APA and V max enhanced with the increasing exposure concentrations. We also found there were no obvious distinctions on the effects of growth and alkaline phosphatase in M. aeruginosa between PM 2.5-10 and PM >10 exposure groups. Obviously, inhibitory effects on growth existed in 4.0 and 8.0 mg/L PM 2.5-10 and 8.0 mg/L PM >10 at 120 h. Furthermore, PM 2.5-10 and PM >10 exerted inhibitory effects on the extracellular APA during the 72-h exposure. Simultaneously, the V max was notably inhibited and the affinity of alkaline phosphatase for substrate was more inseparable compared with control in PM 2.5-10 and PM >10 treatments. Nevertheless, the inhibitors in extracellular APA and kinetic parameters were unrelated to PM 2.5-10 and PM >10 exposure concentrations. Two-way ANOVA results revealed that there were significant interactions between exposure concentration and diameter of APM on the 120-h cell density, soluble protein content, APA, and 72 h APA of M. aeruginosa. These results in our study would be meaningful to further

Using support vector regression to predict PM10 and PM2.5

International Nuclear Information System (INIS)

Weizhen, Hou; Zhengqiang, Li; Yuhuan, Zhang; Hua, Xu; Ying, Zhang; Kaitao, Li; Donghui, Li; Peng, Wei; Yan, Ma

2014-01-01

Support vector machine (SVM), as a novel and powerful machine learning tool, can be used for the prediction of PM 10 and PM 2.5 (particulate matter less or equal than 10 and 2.5 micrometer) in the atmosphere. This paper describes the development of a successive over relaxation support vector regress (SOR-SVR) model for the PM 10 and PM 2.5 prediction, based on the daily average aerosol optical depth (AOD) and meteorological parameters (atmospheric pressure, relative humidity, air temperature, wind speed), which were all measured in Beijing during the year of 2010–2012. The Gaussian kernel function, as well as the k-fold crosses validation and grid search method, are used in SVR model to obtain the optimal parameters to get a better generalization capability. The result shows that predicted values by the SOR-SVR model agree well with the actual data and have a good generalization ability to predict PM 10 and PM 2.5 . In addition, AOD plays an important role in predicting particulate matter with SVR model, which should be included in the prediction model. If only considering the meteorological parameters and eliminating AOD from the SVR model, the prediction results of predict particulate matter will be not satisfying

Determinants of exposure to fine particulate matter (PM 2.5) for waiting passengers at bus stops

Science.gov (United States)

Hess, Daniel Baldwin; Ray, Paul David; Stinson, Anne E.; Park, JiYoung

2010-12-01

This research evaluates commuter exposure to particulate matter during pre-journey commute segments for passengers waiting at bus stops by investigating 840 min of simultaneous exposure levels, both inside and outside seven bus shelters in Buffalo, New York. A multivariate regression model is used to estimate the relation between exposure to particulate matter (PM 2.5 measured in μg m -3) and three vectors of determinants: time and location, physical setting and placement, and environmental factors. Four determinants have a statistically significant effect on particulate matter: time of day, passengers' waiting location, land use near the bus shelter, and the presence of cigarette smoking at the bus shelter. Model results suggest that exposure to PM 2.5 inside a bus shelter is 2.63 μg m -3 (or 18 percent) higher than exposure outside a bus shelter, perhaps due in part to the presence of cigarette smoking. Morning exposure levels are 6.51 μg m -3 (or 52 percent) higher than afternoon levels. Placement of bus stops can affect exposure to particulate matter for those waiting inside and outside of shelters: air samples at bus shelters located in building canyons have higher particulate matter than bus shelters located near open space.

Atmospheric Distribution of PAHs and Quinones in the Gas and PM1 Phases in the Guadalajara Metropolitan Area, Mexico: Sources and Health Risk

Directory of Open Access Journals (Sweden)

Valeria Ojeda-Castillo

2018-04-01

Full Text Available Polycyclic aromatic hydrocarbons (PAHs and quinones in the gas phase and as submicron particles raise concerns due to their potentially carcinogenic and mutagenic properties. The majority of existing studies have investigated the formation of quinones, but it is also important to consider both the primary and secondary sources to estimate their contributions. The objectives of this study were to characterize PAHs and quinones in the gas and particulate matter (PM1 phases in order to identify phase distributions, sources, and cancer risk at two urban monitoring sites in the Guadalajara Metropolitan Area (GMA in Mexico. The simultaneous gas and PM1 phases samples were analyzed using a gas chromatography–mass spectrometer. The lifetime lung cancer risk (LCR due to PAH exposure was calculated to be 1.7 × 10−3, higher than the recommended risk value of 10−6, indicating a potential health hazard. Correlations between parent PAHs, criteria pollutants, and meteorological parameters suggest that primary sources are the main contributors to the Σ8 Quinones concentrations in PM1, while the secondary formation of 5,12-naphthacenequinone and 9,10-anthraquinone may contribute less to the observed concentration of quinones. Additionally, naphthalene, acenaphthene, fluorene, phenanthrene, and anthracene in PM1, suggest photochemical degradation into unidentified species. Further research is needed to determine how these compounds are formed.

Variability of intra-urban exposure to particulate matter and CO from Asian-type community pollution sources

Science.gov (United States)

Lung, Shih-Chun Candice; Hsiao, Pao-Kuei; Wen, Tzu-Yao; Liu, Chun-Hu; Fu, Chi Betsy; Cheng, Yu-Ting

2014-02-01

Asian residential communities are usually dotted with various spot pollution sources (SPS), such as restaurants, temples, and home factories, with traffic arteries passing through, resulting in higher intra-urban pollution variability compared with their western counterparts. Thus, it is important to characterize spatial variability of pollutant levels in order to assess accurately residents' exposures in their communities. The objectives of this study are to assess the actual pollutant levels and variability within an Asian urban area and to evaluate the influence of vehicle emission and various SPS on the exposure levels within communities. Real-time monitoring was conducted for a total of 123 locations for particulate matter (PM) and CO in Taipei metropolitan, Taiwan. The mean concentrations for PM1, PM2.5, PM10, and CO are 29.8 ± 22.7, 36.0 ± 25.5, 61.9 ± 35.0 μg m-3 and 4.0 ± 2.5 ppm, respectively. The mean values of PM1/PM2.5 and PM2.5/PM10 are 0.80 ± 0.10 and 0.57 ± 0.15, respectively. PM and CO levels at locations near SPS could be increased by 3.5-4.9 times compared with those at background locations. Regression results show that restaurants contribute significantly 6.18, 6.33, 7.27 μg m-3, and 1.64 ppm to community PM1, PM2.5, PM10, and CO levels, respectively; while the contribution from temples are 13.2, 15.1, and 17.2 μg m-3 for PM1, PM2.5 and PM10, respectively. Additionally, construction sites elevate nearby PM10 levels by 14.2 μg m-3. At bus stops and intersections, vehicle emissions increased PM1 and PM2.5 levels by 5 μg m-3. These results demonstrate significant contribution of community sources to air pollution, and thus the importance of assessing intra-community variability in Asian cities for air pollution and health studies. The methodology used is applicable to other Asian countries with similar features.

Transport and solubility of Hetero-disperse dry deposition particulate matter subject to urban source area rainfall-runoff processes

Science.gov (United States)

Ying, G.; Sansalone, J.

2010-03-01

SummaryWith respect to hydrologic processes, the impervious pavement interface significantly alters relationships between rainfall and runoff. Commensurate with alteration of hydrologic processes the pavement also facilitates transport and solubility of dry deposition particulate matter (PM) in runoff. This study examines dry depositional flux rates, granulometric modification by runoff transport, as well as generation of total dissolved solids (TDS), alkalinity and conductivity in source area runoff resulting from PM solubility. PM is collected from a paved source area transportation corridor (I-10) in Baton Rouge, Louisiana encompassing 17 dry deposition and 8 runoff events. The mass-based granulometric particle size distribution (PSD) is measured and modeled through a cumulative gamma function, while PM surface area distributions across the PSD follow a log-normal distribution. Dry deposition flux rates are modeled as separate first-order exponential functions of previous dry hours (PDH) for PM and suspended, settleable and sediment fractions. When trans-located from dry deposition into runoff, PSDs are modified, with a d50m decreasing from 331 to 14 μm after transport and 60 min of settling. Solubility experiments as a function of pH, contact time and particle size using source area rainfall generate constitutive models to reproduce pH, alkalinity, TDS and alkalinity for historical events. Equilibrium pH, alkalinity and TDS are strongly influenced by particle size and contact times. The constitutive leaching models are combined with measured PSDs from a series of rainfall-runoff events to demonstrate that the model results replicate alkalinity and TDS in runoff from the subject watershed. Results illustrate the granulometry of dry deposition PM, modification of PSDs along the drainage pathway, and the role of PM solubility for generation of TDS, alkalinity and conductivity in urban source area rainfall-runoff.

Characterization of PM10 sources in the central Mediterranean

Science.gov (United States)

Calzolai, G.; Nava, S.; Lucarelli, F.; Chiari, M.; Giannoni, M.; Becagli, S.; Traversi, R.; Marconi, M.; Frosini, D.; Severi, M.; Udisti, R.; di Sarra, A.; Pace, G.; Meloni, D.; Bommarito, C.; Monteleone, F.; Anello, F.; Sferlazzo, D. M.

2015-12-01

The Mediterranean Basin atmosphere is influenced by both strong natural and anthropogenic aerosol emissions and is also subject to important climatic forcings. Several programs have addressed the study of the Mediterranean basin; nevertheless important pieces of information are still missing. In this framework, PM10 samples were collected on a daily basis on the island of Lampedusa (35.5° N, 12.6° E; 45 m a.s.l.), which is far from continental pollution sources (the nearest coast, in Tunisia, is more than 100 km away). After mass gravimetric measurements, different portions of the samples were analyzed to determine the ionic content by ion chromatography (IC), the soluble metals by inductively coupled plasma atomic emission spectrometry (ICP-AES), and the total (soluble + insoluble) elemental composition by particle-induced x-ray emission (PIXE). Data from 2007 and 2008 are used in this study. The Positive Matrix Factorization (PMF) model was applied to the 2-year long data set of PM10 mass concentration and chemical composition to assess the aerosol sources affecting the central Mediterranean basin. Seven sources were resolved: sea salt, mineral dust, biogenic emissions, primary particulate ship emissions, secondary sulfate, secondary nitrate, and combustion emissions. Source contributions to the total PM10 mass were estimated to be about 40 % for sea salt, around 25 % for mineral dust, 10 % each for secondary nitrate and secondary sulfate, and 5 % each for primary particulate ship emissions, biogenic emissions, and combustion emissions. Large variations in absolute and relative contributions are found and appear to depend on the season and on transport episodes. In addition, the secondary sulfate due to ship emissions was estimated and found to contribute by about one-third to the total sulfate mass. Results for the sea-salt and mineral dust sources were compared with estimates of the same contributions obtained from independent approaches, leading to an

Scenario Study on PM emission Reduction in Cement Industry

Science.gov (United States)

Tang, Qian; Chen, Xiaojun; Xia, Xin; Wang, Lijuan; Wang, Huili; Jin, Ling; Yan, Zhen

2018-01-01

Cement industry is one of the high pollution industries in China. Evaluation of the primary particulate matter (PM) emission status and the reduction potential is not only important for our understanding of the effectiveness of current pollution control measures but also vital for future policy design. In this study, PM emitted from cement producing process in 2014 was calculated using an emission factor method. Three PM emission control scenarios were set up considering source control, process management and end-of-pipe treatment, and the PM emission reduction by 2020 under the three scenarios was predicted, respectively. In 2014, the primary PM emission from cement industry was 1.95 million tons. By 2020, the productions of cement and clinker were expected to increase by 12% and 7%, respectively, and the PM emission would increase by about 10%. By implementation of GB4915-2013 and comprehensive control of fugitive PM emission, the PM emission would probably be reduced by 34%. Another 7% decrease would be expected from source control. The second scenario can be considered as an assessment of the effectiveness of the revised emission standard, and this research can be used as a technical support to the environmental management authorities to make relevant policies.

Complex time series analysis of PM10 and PM2.5 for a coastal site using artificial neural network modelling and k-means clustering

Science.gov (United States)

Elangasinghe, M. A.; Singhal, N.; Dirks, K. N.; Salmond, J. A.; Samarasinghe, S.

2014-09-01

This paper uses artificial neural networks (ANN), combined with k-means clustering, to understand the complex time series of PM10 and PM2.5 concentrations at a coastal location of New Zealand based on data from a single site. Out of available meteorological parameters from the network (wind speed, wind direction, solar radiation, temperature, relative humidity), key factors governing the pattern of the time series concentrations were identified through input sensitivity analysis performed on the trained neural network model. The transport pathways of particulate matter under these key meteorological parameters were further analysed through bivariate concentration polar plots and k-means clustering techniques. The analysis shows that the external sources such as marine aerosols and local sources such as traffic and biomass burning contribute equally to the particulate matter concentrations at the study site. These results are in agreement with the results of receptor modelling by the Auckland Council based on Positive Matrix Factorization (PMF). Our findings also show that contrasting concentration-wind speed relationships exist between marine aerosols and local traffic sources resulting in very noisy and seemingly large random PM10 concentrations. The inclusion of cluster rankings as an input parameter to the ANN model showed a statistically significant (p advanced air dispersion models.

Source apportionment and spatial variability of PM2.5 using measurements at five sites in the Netherlands

NARCIS (Netherlands)

Mooibroek, D.; Schaap, M.; Weijers, E.P.; Hoogerbrugge, R.

2011-01-01

The Netherlands is considered one of the hotspot areas in Europe with high concentrations of particulate matter (PM) and may not be able to meet all standards for PM2.5 in time with current legislation (Matthijsen et al., 2009). To improve our understanding of the composition, distribution and

[Exploration of a quantitative methodology to characterize the retention of PM2.5 and other atmospheric particulate matter by plant leaves: taking Populus tomentosa as an example].

Science.gov (United States)

Zhang, Zhi-Dan; Xi, Ben-Ye; Cao, Zhi-Guo; Jia, Li-Ming

2014-08-01

Taking Populus tomentosa as an example, a methodology called elution-weighing-particle size-analysis (EWPA) was proposed to evaluate quantitatively the ability of retaining fine particulate matter (PM2.5, diameter d ≤ 2.5 μm) and atmospheric particulate matter by plant leaves using laser particle size analyzer and balance. This method achieved a direct, accurate measurement with superior operability about the quality and particle size distribution of atmospheric particulate matter retained by plant leaves. First, a pre-experiment was taken to test the stability of the method. After cleaning, centrifugation and drying, the particulate matter was collected and weighed, and then its particle size distribution was analyzed by laser particle size analyzer. Finally, the mass of particulate matter retained by unit area of leaf and stand was translated from the leaf area and leaf area index. This method was applied to a P. tomentosa stand which had not experienced rain for 27 days in Beijing Olympic Forest Park. The results showed that the average particle size of the atmospheric particulate matter retained by P. tomentosa was 17.8 μm, and the volume percentages of the retained PM2.5, inhalable particulate matter (PM10, d ≤ 10 μm) and total suspended particle (TSP, d ≤ 100 μm) were 13.7%, 47.2%, and 99.9%, respectively. The masses of PM2.5, PM10, TSP and total particulate matter were 8.88 x 10(-6), 30.6 x 10(-6), 64.7 x 10(-6) and 64.8 x 10(-6) g x cm(-2) respectively. The retention quantities of PM2.5, PM10, TSP and total particulate matter by the P. tomentosa stand were 0.963, 3.32, 7.01 and 7.02 kg x hm(-2), respectively.

PM sources in a highly industrialised area in the process of implementing PM abatement technology. Quantification and evolution.

Science.gov (United States)

Cruz Minguillón, María; Querol, Xavier; Alastuey, Andrés; Monfort, Eliseo; Vicente Miró, José

2007-10-01

Principal component analysis (PCA) coupled with a multilinear regression analysis (MLRA) was applied to PM(10) speciation data series (2002-2005) from four sampling sites in a highly industrialised area (ceramic production) in the process of implementing emission abatement technology. Five common factors with similar chemical profiles were identified at all the sites: mineral, regional background (influenced by the industrial estate located on the coast: an oil refinery and a power plant), sea spray, industrial 1 (manufacture and use of glaze components, including frit fusion) and road traffic. The contribution of the regional background differs slightly from site to site. The mineral factor, attributed to the sum of several sources (mainly the ceramic industry, but also with minor contributions from soil resuspension and African dust outbreaks) contributes between 9 and 11 microg m(-3) at all the sites. Source industrial 1 entails an increase in PM(10) levels between 4 and 5 microg m(-3) at the urban sites and 2 microg m(-3) at the suburban background site. However, after 2004, this source contributed less than 2 microg m(-3) at most sites, whereas the remaining sources did not show an upward or downward trend along the study period. This gradual decrease in the contribution of source industrial 1 coincides with the implementation of PM abatement technology in the frit fusion kilns of the area. This relationship enables us to assess the efficiency of the implementation of environmental technologies in terms of their impact on air quality.

Influence of Saharan dust outbreaks and carbon content on oxidative potential of water-soluble fractions of PM2.5 and PM10

Science.gov (United States)

Chirizzi, Daniela; Cesari, Daniela; Guascito, Maria Rachele; Dinoi, Adelaide; Giotta, Livia; Donateo, Antonio; Contini, Daniele

2017-08-01

Exposure to atmospheric particulate matter (PM) leads to adverse health effects although the exact mechanisms of toxicity are still poorly understood. Several studies suggested that a large number of PM health effects could be due to the oxidative potential (OP) of ambient particles leading to high concentrations of reactive oxygen species (ROS). The contribution to OP of specific anthropogenic sources like road traffic, biomass burning, and industrial emissions has been investigated in several sites. However, information about the OP of natural sources are scarce and no data is available regarding the OP during Saharan dust outbreaks (SDO) in Mediterranean regions. This work uses the a-cellular DTT (dithiothreitol) assay to evaluate OP of the water-soluble fraction of PM2.5 and PM10 collected at an urban background site in Southern Italy. OP values in three groups of samples were compared: standard characterised by concentrations similar to the yearly averages; high carbon samples associated to combustion sources (mainly road traffic and biomass burning) and SDO events. DTT activity normalised by sampled air volume (DTTV), representative of personal exposure, and normalised by collected aerosol mass (DTTM), representing source-specific characteristics, were investigated. The DTTV is larger for high PM concentrations. DTTV is well correlated with secondary organic carbon concentration. An increased DTTV response was found for PM2.5 compared to the coarse fraction PM2.5-10. DTTV is larger for high carbon content samples but during SDO events is statistically comparable with that of standard samples. DTTM is larger for PM2.5 compared to PM10 and the relative difference between the two size fractions is maximised during SDO events. This indicates that Saharan dust advection is a natural source of particles having a lower specific OP with respect to the other sources acting on the area (for water-soluble fraction). OP should be taken into account in epidemiological

PM levels in urban area of Bejaia

Science.gov (United States)

Benaissa, Fatima; Maesano, Cara Nichole; Alkama, Rezak; Annesi-Maesano, Isabella

2017-04-01

Air pollution is not routinely measured in Bejaia City, Algeria, an urban area of around 200,000 inhabitants. We present first time measurements of particulate matter (PM) mass concentrations for this city (PM10, PM7, PM4, PM2.5 and PM1) over the course of one week, from July 8 to July 14, 2015. This study covered eight urban sampling sites and 169 measurements were obtained to determine mass concentration levels. Air pollution is not routinely measured in Bejaia City, Algeria, an urban area of around 200,000 inhabitants. We present first time measurements of particulate matter (PM) mass concentrations for this city (PM10, PM7, PM4, PM2.5 and PM1) over the course of one week, from July 8 to July 14, 2015. This study covered eight urban sampling sites and 169 measurements were obtained to determine mass concentration levels. The average city-wide PM10 and PM2.5 concentrations measured during this sampling were 87.8 ± 33.9 and 28.7 ± 10.6 µg/m3 respectively. These results show that particulate matter levels are high and exceed Algerian ambient air quality standards (maximum 80 µg/m3, without specifying the particle size). Further, PM10 and PM2.5 averages were well above the prescribed 24-hour average World Health Organization Air Quality Guidelines (WHO AQG) (50 µg/m3 for PM10 and 25 µg/m3 for PM2.5). The PM1, PM2,5, PM4 and PM7 fractions accounted for 15%, 32 %, 56% and 78% respectively of the PM10 measurements. Our analysis reveals that PM concentration variations in the study region were influenced primarily by traffic. In fact, lower PM10 concentrations (21.7 and 33.1 µg/m3) were recorded in residential sites while higher values (53.1, and 45.2 µg/m3) were registered in city centers. Keywords: Particulate matter, Urban area, vehicle fleet, Bejaia.

Air pollution studies in terms of PM2.5, PM2.5-10, PM10, lead and black carbon in urban areas of Antananarivo-Madagascar

International Nuclear Information System (INIS)

Rasoazanany, E. O.; Andriamahenina, N. N.; Ravoson, H. N.; Raoelina Andriambololona; Randriamanivo, L. V.; Ramaherison, H.; Ahmed, H.; Harinoely, M.

2011-01-01

Atmospheric aerosols or particulate matters are chemically complex and dynamic mixtures of solid and liquid particles. Sources of particulate matters include both natural and anthropogenic processes. The present work consists in determining the concentrations of existing elements in the aerosols collected in Andravoahangy and in Ambodin Isotry in Antananarivo city (Madagascar). The size distribution of these elements and their main sources are also studied.The Total Reflection X-Ray Fluorescence spectrometer is used for the qualitative and quantitative analyses. The results show that the concentrations of the airborne particulate matters PM 2.5-10 are higher than those of PM 2.5 .The identified elements in the aerosol samples are Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Sr and Pb. The average concentrations of these elements are also higher in the coarse particles than in the fine particles. The calculation of the enrichment factors by Mason's model shows that Cr, Ni, Cu, Zn, Br and Pb are of anthropogenic origins. The average concentrations of lead (2.8 ng.m -3 , 31.3 ng.m -3 and 19.6 ng.m -3 respectively in aerosols collected in Andravoahangy in 2007 and in 2008 and in Ambodin Isotry in 2008) are largely lower than the average concentration of 1.8 μg.m -3 obtained in 2000 in the Antananarivo urban areas. The concentration of black carbon is higher in the fine particles. The Air Quality Index category is variable in the two sites.

Chemical characteristics and source apportionment of fine particulate organic carbon in Hong Kong during high particulate matter episodes in winter 2003

Science.gov (United States)

Li, Yun-Chun; Yu, Jian Zhen; Ho, Steven Sai Hang; Schauer, James J.; Yuan, Zibing; Lau, Alexis K. H.; Louie, Peter K. K.

2013-02-01

PM2.5 samples were collected at six general stations and one roadside station in Hong Kong in two periods of high particulate matter (PM) in 2003 (27 October-4 November and 30 November-13 December). The highest PM2.5 reached 216 μg m- 3 during the first high PM period and 113 μg m- 3 during the second high PM period. Analysis of synoptic weather conditions identified individual sampling days under dominant influence of one of three types of air masses, that is, local, regional and long-range transported (LRT) air masses. Roadside samples were discussed separately due to heavy influences from vehicular emissions. This research examines source apportionment of fine organic carbon (OC) and contribution of secondary organic aerosol on high PM days under different synoptic conditions. Six primary OC (POC) sources (vehicle exhaust, biomass burning, cooking, cigarette smoke, vegetative detritus, and coal combustion) were identified on the basis of characteristic organic tracers. Individual POC source contributions were estimated using chemical mass balance model. In the roadside and the local samples, OC was dominated by the primary sources, accounting for more than 74% of OC. In the samples influenced by regional and LRT air masses, secondary OC (SOC), which was approximated to be the difference between the total measured OC and the apportioned POC, contributed more than 54% of fine OC. SOC was highly correlated with water-soluble organic carbon and sulfate, consistent with its secondary nature.

Within-city contrasts in PM composition and sources and their relationship with nitrogen oxides.

Science.gov (United States)

Minguillón, M C; Rivas, I; Aguilera, I; Alastuey, A; Moreno, T; Amato, F; Sunyer, J; Querol, X

2012-10-26

The present work is part of the INMA (INfancia y Medio Ambiente -'Environment and Childhood') project, which aims at assessing the adverse effects of exposure to air pollution during pregnancy and early in life. The present study was performed in the city of Sabadell (Northeast Spain) at three sampling sites covering different traffic characteristics, during two times of the year. It assesses time and spatial variations of PM(2.5) concentrations, chemical components and source contributions, as well as gaseous pollutants. Furthermore, a cross-correlation analysis of PM components and source contributions with gaseous pollutants used as a proxy for exposure assessment is carried out. Our data show the influence of traffic emissions in the Sabadell area. The main PM sources identified by Positive Matrix Factorisation (PMF) were similar between the two seasons: mineral source (traffic-induced resuspension, demolition/construction and natural background), secondary sulphate (higher in summer), secondary nitrate (only during winter), industrial, and road traffic, which was the main contributor to PM(2.5) at two of the sites. The correlation of concentrations of nitrogen oxides was especially strong with those of elemental carbon (EC). The relatively weaker correlations with organic carbon (OC) in summer are attributed to the variable formation of secondary OC. Strong correlations between concentration of nitrogen oxides and PM(2.5) road traffic contributions obtained from source apportionment analysis were seen at all sites. Therefore, under the studied urban environment, nitrogen oxides can be used as a proxy for the exposure to road traffic contribution to PM(2.5); the use of NO(x) concentrations being preferred, with NO and NO(2) as second and third options, respectively.

Joint measurements of PM2. 5 and light-absorptive PM in woodsmoke-dominated ambient and plume environments

Science.gov (United States)

Zhang, K. Max; Allen, George; Yang, Bo; Chen, Geng; Gu, Jiajun; Schwab, James; Felton, Dirk; Rattigan, Oliver

2017-09-01

DC, also referred to as Delta-C, measures enhanced light absorption of particulate matter (PM) samples at the near-ultraviolet (UV) range relative to the near-infrared range, which has been proposed previously as a woodsmoke marker due to the presence of enhanced UV light-absorbing materials from wood combustion. In this paper, we further evaluated the applications and limitations of using DC as both a qualitative and semi-quantitative woodsmoke marker via joint continuous measurements of PM2. 5 (by nephelometer pDR-1500) and light-absorptive PM (by 2-wavelength and 7-wavelength Aethalometertext">®) in three northeastern US cities/towns including Rutland, VT; Saranac Lake, NY and Ithaca, NY. Residential wood combustion has shown to be the predominant source of wintertime primary PM2. 5 emissions in both Rutland and Saranac Lake, where we conducted ambient measurements. In Ithaca, we performed woodsmoke plume measurements. We compared the pDR-1500 against a FEM PM2. 5 sampler (BAM 1020), and identified a close agreement between the two instruments in a woodsmoke-dominated ambient environment. The analysis of seasonal and diurnal trends of DC, black carbon (BC, 880 nm) and PM2. 5 concentrations supports the use of DC as an adequate qualitative marker. The strong linear relationships between PM2. 5 and DC in both woodsmoke-dominated ambient and plume environments suggest that DC can reasonably serve as a semi-quantitative woodsmoke marker. We propose a DC-based indicator for woodsmoke emission, which has shown to exhibit a relatively strong linear relationship with heating demand. While we observed reproducible PM2. 5-DC relationships in similar woodsmoke-dominated ambient environments, those relationships differ significantly with different environments, and among individual woodsmoke sources. Our analysis also indicates the potential for PM2. 5-DC relationships to be utilized to distinguish different combustion and operating conditions of woodsmoke sources, and

Characteristics and major sources of carbonaceous aerosols in PM{sub 2.5} from Sanya, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Jingzhi [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Ho, Steven Sai Hang [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Division of Atmospheric Sciences, Desert Research Institute, Reno, NV (United States); Cao, Junji, E-mail: cao@loess.llqg.ac.cn [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Institute of Global Environmental Change, Xi' an Jiaotong University, Xi' an (China); Huang, Rujin [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Laboratory of Atmospheric Chemistry, Paul Scherrer Institute (PSI), 5232 Villigen (Switzerland); Zhou, Jiamao [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Zhao, Youzhi [College of Science and Technology, Qiongzhou University, Sanya (China); Xu, Hongmei [Department of Environmntal Science and Engineering, Xi' an Jiaotong University, Xi' an (China); Liu, Suixin; Wang, Gehui [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); and others

2015-10-15

PM{sub 2.5} samples were collected in Sanya, China in summer and winter in 2012/2013. Organic carbon (OC), elemental carbon (EC), and non-polar organic compounds including n-alkanes (n-C{sub 14}-n-C{sub 40}) and polycyclic aromatic hydrocarbons (PAHs) were quantified. The concentrations of these carbonaceous matters were generally higher in winter than summer. The estimated secondary organic carbon (OC{sub sec}) accounted for 38% and 54% of the total organic carbon (TOC) in winter and summer, respectively. The higher value of OC{sub sec} in addition to the presences of photochemically-produced PAHs in summer supports that photochemical conversions of organics are much active at the higher air temperatures and with stronger intense solar radiation. Carbon preference index (CPI) and percent contribution of wax n-alkanes suggest that anthropogenic sources were more dominant than derivation from terrestrial plants in Sanya. Diagnostic ratios of atmospheric PAHs further indicate that there was a wide mix of pollution sources in winter while fossil fuel combustion was the most dominant in summer. Positive Matrix Factorization (PMF) analysis with 18 PAHs in the winter samples found that motor vehicle emissions and biomass burning were the two main pollution sources, contributing 37.5% and 24.6% of the total quantified PAHs, respectively. - Highlights: • The first comprehensive study to investigate carbonaceous PM{sub 2.5} in Sanya, China • Higher carbonaceous levels in winter while more SOC formation in summer • Anthropogenic emission is the dominant sources of n-alkanes • Vehicle emission and biomass burning contributed ≥60% of the total PAHs in winter • The result supports better air quality in Sanya than most megacities in China.

CARDIOVASCULAR MORTALITY IN PHOENIX: PM1 IS A BETTER INDICATOR THAN PM2.5.

Science.gov (United States)

EPA has obtained a 3-year database of particulate matter (PM) in Phoenix, AZ from 1995 - 1997 that includes elemental analysis by XRF of daily PM2.5. During this time period PM1 and PM2.5 TEOMs were run simultaneously for about 7 months during two periods of the year. Regressio...

Source apportionment of carbonaceous particulate matter during haze days in Shanghai based on the radiocarbon

International Nuclear Information System (INIS)

Nannan Wei; Jialiang Feng; Detao Xiao

2017-01-01

To estimate the sources of carbonaceous particulate matter, "1"4C and biomass-burning marker (levoglucosan) were measured in the form of organic carbon (OC) and elemental carbon (EC) in PM_2_._5 that was collected in five different functional districts of Shanghai during winter 2013. Spatial variations of the contemporary proportion among different districts were evident. The results of levoglucosan in Xujiahui (XH) and Chongming (CM) agreed well with those of "1"4C. The results indicate that environmental protection policies should vary for functional districts within the same city to account for their different sources of emissions. (author)

Evaluation of sampling inhalable PM10 particulate matter (≤ 10 μm) using co-located high volume samplers

International Nuclear Information System (INIS)

Rajoy, R R S; Dias, J W C; Rego, E C P; Netto, A D Pereira

2015-01-01

This paper presents the results of the determination of the concentrations of atmospheric particulate matter ≤ 10 μm (PM10), collected simultaneously by six PM10 high volume samplers from two different manufacturers installed in the same location. Fifteen samples of 24 h were obtained with each equipment at a selected urban area of Rio de Janeiro city. The concentration of PM10 ranged between 10.73 and 54.04 μg m −3 . The samplers were considered comparable to each other, as the adopted methodology presented good repeatability

SOURCE SAMPLING FINE PARTICULATE MATTER--INSTITUTIONAL OIL-FIRED BOILER

Science.gov (United States)

EPA seeks to understand the correlation between ambient fine PM and adverse human health effects, and there are no reliable emission factors to use for estimating PM2.5 or NH3. The most common source of directly emitted PM2.5 is incomplete combustion of fossil or biomass fuels. M...

Size distribution, directional source contributions and pollution status of PM from Chengdu, China during a long-term sampling campaign.

Science.gov (United States)

Shi, Guo-Liang; Tian, Ying-Ze; Ma, Tong; Song, Dan-Lin; Zhou, Lai-Dong; Han, Bo; Feng, Yin-Chang; Russell, Armistead G

2017-06-01

Long-term and synchronous monitoring of PM 10 and PM 2.5 was conducted in Chengdu in China from 2007 to 2013. The levels, variations, compositions and size distributions were investigated. The sources were quantified by two-way and three-way receptor models (PMF2, ME2-2way and ME2-3way). Consistent results were found: the primary source categories contributed 63.4% (PMF2), 64.8% (ME2-2way) and 66.8% (ME2-3way) to PM 10 , and contributed 60.9% (PMF2), 65.5% (ME2-2way) and 61.0% (ME2-3way) to PM 2.5 . Secondary sources contributed 31.8% (PMF2), 32.9% (ME2-2way) and 31.7% (ME2-3way) to PM 10 , and 35.0% (PMF2), 33.8% (ME2-2way) and 36.0% (ME2-3way) to PM 2.5 . The size distribution of source categories was estimated better by the ME2-3way method. The three-way model can simultaneously consider chemical species, temporal variability and PM sizes, while a two-way model independently computes datasets of different sizes. A method called source directional apportionment (SDA) was employed to quantify the contributions from various directions for each source category. Crustal dust from east-north-east (ENE) contributed the highest to both PM 10 (12.7%) and PM 2.5 (9.7%) in Chengdu, followed by the crustal dust from south-east (SE) for PM 10 (9.8%) and secondary nitrate & secondary organic carbon from ENE for PM 2.5 (9.6%). Source contributions from different directions are associated with meteorological conditions, source locations and emission patterns during the sampling period. These findings and methods provide useful tools to better understand PM pollution status and to develop effective pollution control strategies. Copyright © 2016. Published by Elsevier B.V.

Background PM2.5 source apportionment in the remote Northwestern United States

Science.gov (United States)

Hadley, Odelle L.

2017-10-01

This study used the Environmental Protection Agency's positive matrix factorization model (EPA PMF5.0) to identify five primary source factors contributing to the ambient PM2.5 concentrations at Cheeka Peak Atmospheric Observatory (CPO), Neah Bay WA between January 2011 and December 2014. CPO is home to both an IMPROVE (Interagency Monitoring for Protected Visual Environments) and a NCore multi-pollutant monitoring site. Chemically resolved particulate data from the IMPROVE site was the input data to EPA PMF5.0 and the resulting source factors were derived solely from these data. Solutions from the model were analyzed in context with trace gas and meteorological data collected at the NCore site located roughly 10 m away. Seasonal and long-term trends were analyzed for all five factors and provide the first complete source apportionment analysis of PM2.5 at this remote location. The first factor, identified as marine-traffic residual fuel oil (RFO), was the highest contributor to PM2.5 during late summer. Over the 4-year analysis, the RFO percent contribution to total PM2.5 declined. This is consistent with previous studies and may be attributed to regulations restricting the sulfur content of ship fuel. Biomass combustion emissions (BMC) and sea salt were the largest PM2.5 sources observed at CPO in winter, accounting for over 80% of the fine particulate. BMC accounted for a large percent of the fine particulate pollution when winds were easterly, or continental. Sea salt was the dominant winter factor when winds blew from the west. Measured trace carbon monoxide (CO) and reactive nitrogen species (NOy) were most strongly correlated with the BMC factor and continental winds. The fourth factor was identified as aged crustal material, or dust. In all three years, dust peaked in the spring and was associated exclusively with north-easterly winds. The last factor was identified as aged sea salt mixed with nitrate, sulfate, and other components common to RFO and BMC

Development of methods to examine the effects of atmospheric particulate matter (PM) on human peripheral blood leukocytes

Science.gov (United States)

Zussman, Lisa Ann

In vitro methods to study the effect of atmospheric particulate matter (PM) on leukocyte function using human peripheral blood were developed. These methods were demonstrated using the blood of 1-5 individuals and National Institute of Standards and Technology (NIST) urban PM #1648, diesel PM #1650, silica PM, and a locally collected PM sample (New Jersey PM10). For the blood samples analyzed in this study NIST urban PM and New Jersey PM10 treatment mediated the release of granule contents from peripheral blood leukocytes and induced structural changes associated with degranulation. Flow cytometry revealed PM-induced changes in phagocytosis and cell structure associated with degranulation. Transmission electron microscopy confirmed NIST urban PM-induced cell structure changes were associated with PM internalization. Colorametric and electrophoretic methods showed no PM-induced release of primary granules and a slight PM-induced release of secondary granules associated with only NIST urban PM. Enzyme Immunosorbent Assays detected increased histamine release from basophils treated with NIST urban PM, a locally collected PM, and the soluble and insoluble components of these particles. NIST urban PM was found to be a potent inducer of histamine release in 4 out of 6 individuals tested. Fractionation studies revealed that soluble (aqueous) and insoluble fractions of NIST urban PM contain histamine-releasing activity. This was also demonstrated for the New Jersey PM10 sample for which the soluble fraction exhibited the most activity. Complementary studies with inhibitors of IgE-mediated histamine release conducted on one test subject suggest that PM-induced histamine release was partially mediated by IgE. A new hypothesis has been formed, suggesting that particle toxicity is related to PM-induced histamine release. Due to the bioactive nature of histamine and its association with many cardiopulmonary responses, the PM- mediated release of histamine should be investigated

Statins attenuate the development of atherosclerosis and endothelial dysfunction induced by exposure to urban particulate matter (PM10)

International Nuclear Information System (INIS)

Miyata, Ryohei; Hiraiwa, Kunihiko; Cheng, Jui Chih; Bai, Ni; Vincent, Renaud; Francis, Gordon A.; Sin, Don D.; Van Eeden, Stephan F.

2013-01-01

Exposure to ambient air particulate matter (particles less than 10 μm or PM 10 ) has been shown to be an independent risk factor for the development and progression of atherosclerosis. The 3-hydroxy-3-methylglutaryl coenzyme A reductase inhibitors (statins) have well-established anti-inflammatory properties. The aim of this study was to determine the impact of statins on the adverse functional and morphological changes in blood vessels induced by PM 10 . New Zealand White rabbits fed with a high fat diet were subjected to balloon injury to their abdominal aorta followed by PM 10 /saline exposure for 4 weeks ± lovastatin (5 mg/kg/day) treatment. PM 10 exposure accelerated balloon catheter induced plaque formation and increased intimal macrophages and lipid accumulation while lovastatin attenuated these changes and promoted smooth muscle cell recruitment into plaques. PM 10 impaired vascular acetylcholine (Ach) responses and increased vasoconstriction induced by phenylephrine as assessed by wire myograph. Supplementation of nitric oxide improved the impaired Ach responses. PM 10 increased the expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2) in blood vessels and increased the plasma levels of endothelin-1 (ET-1). Incubation with specific inhibitors for iNOS, COX-2 or ET-1 in the myograph chambers significantly improved the impaired vascular function. Lovastatin decreased the expression of these mediators in atherosclerotic lesions and improved endothelial dysfunction. However, lovastatin was unable to reduce blood lipid levels to the baseline level in rabbits exposed to PM 10 . Taken together, statins protect against PM 10 -induced cardiovascular disease by reducing atherosclerosis and improving endothelial function via their anti-inflammatory properties. - Highlights: • Coarse particulate matter (PM 10 ) accelerated balloon injury-induced plaque formation. • Lovastatin decreased intimal macrophages, lipid accumulation, and

Spatial Correlation Analysis between Particulate Matter 10 (PM10) Hazard and Respiratory Diseases in Chiang Mai Province, Thailand

Science.gov (United States)

Trang, N. Ha; Tripathi, N. K.

2014-11-01

Every year, during dry season, Chiang Mai and other northern provinces of Thailand face the problem of haze which is mainly generated by the burning of agricultural waste and forest fire, contained high percentage of particulate matter. Particulate matter 10 (PM10), being very small in size, can be inhaled easily to the deepest parts of the human lung and throat respiratory functions. Due to this, it increases the risk of respiratory diseases mainly in the case of continuous exposure to this seasonal smog. MODIS aerosol images (MOD04) have been used for four weeks in March 2007 for generating the hazard map by linking to in-situ values of PM10. Simple linear regression model between PM10 and AOD got fair correlation with R2 = 0.7 and was applied to transform PM10 pattern. The hazard maps showed the dominance of PM10 in northern part of Chiang Mai, especially in second week of March when PM10 level was three to four times higher than standard. The respiratory disease records and public health station of each village were collected from Provincial Public Health Department in Chiang Mai province. There are about 300 public health stations out of 2070 villages; hence thiessen polygon was created to determine the representative area of each public health station. Within each thiessen polygon, respiratory disease incident rate (RDIR) was calculated based on the number of patients and population. Global Moran's I was computed for RDIR to explore spatial pattern of diseases through four weeks of March. Moran's I index depicted a cluster pattern of respiratory diseases in 2nd week than other weeks. That made sense for a relationship between PM10 and respiratory diseases infections. In order to examine how PM10 affect the human respiratory system, geographically weighted regression model was used to observe local correlation coefficient between RDIR and PM10 across study area. The result captured a high correlation between respiratory diseases and high level of PM10 in

Urban particulate matter pollution: a tale of five cities.

Science.gov (United States)

Pandis, Spyros N; Skyllakou, Ksakousti; Florou, Kalliopi; Kostenidou, Evangelia; Kaltsonoudis, Christos; Hasa, Erion; Presto, Albert A

2016-07-18

Five case studies (Athens and Paris in Europe, Pittsburgh and Los Angeles in the United States, and Mexico City in Central America) are used to gain insights into the changing levels, sources, and role of atmospheric chemical processes in air quality in large urban areas as they develop technologically. Fine particulate matter is the focus of our analysis. In all cases reductions of emissions by industrial and transportation sources have resulted in significant improvements in air quality during the last few decades. However, these changes have resulted in the increasing importance of secondary particulate matter (PM) which dominates over primary in most cases. At the same time, long range transport of secondary PM from sources located hundreds of kilometres from the cities is becoming a bigger contributor to the urban PM levels in all seasons. "Non-traditional" sources including cooking, and residential and agricultural biomass burning contribute an increasing fraction of the now reduced fine PM levels. Atmospheric chemistry is found to change the chemical signatures of a number of these sources relatively fast both during the day and night, complicating the corresponding source apportionment.

Airborne particulate matter from livestock production systems: A review of an air pollution problem

International Nuclear Information System (INIS)

Cambra-Lopez, Maria; Aarnink, Andre J.A.; Zhao Yang; Calvet, Salvador; Torres, Antonio G.

2010-01-01

Livestock housing is an important source of emissions of particulate matter (PM). High concentrations of PM can threaten the environment, as well as the health and welfare of humans and animals. Particulate matter in livestock houses is mainly coarse, primary in origin, and organic; it can adsorb and contain gases, odorous compounds, and micro-organisms, which can enhance its biological effect. Levels of PM in livestock houses are high, influenced by kind of housing and feeding, animal type, and environmental factors. Improved knowledge on particle morphology, primarily size, composition, levels, and the factors influencing these can be useful to identify and quantify sources of PM more accurately, to evaluate their effects, and to propose adequate abatement strategies in livestock houses. This paper reviews the state-of-the-art of PM in and from livestock production systems. Future research to characterize and control PM in livestock houses is discussed. - Control of particulate matter emissions, a major challenge to modern livestock production.

An integrated approach to identify the origin of PM10 exceedances.

Science.gov (United States)

Amodio, M; Andriani, E; de Gennaro, G; Demarinis Loiotile, A; Di Gilio, A; Placentino, M C

2012-09-01

This study was aimed to the development of an integrated approach for the characterization of particulate matter (PM) pollution events in the South of Italy. PM(10) and PM(2.5) daily samples were collected from June to November 2008 at an urban background site located in Bari (Puglia Region, South of Italy). Meteorological data, particle size distributions and atmospheric dispersion conditions were also monitored in order to provide information concerning the different features of PM sources. The collected data allowed suggesting four indicators to characterize different PM(10) exceedances. PM(2.5)/PM(10) ratio, natural radioactivity, aerosol maps and back-trajectory analysis and particle distributions were considered in order to evaluate the contribution of local anthropogenic sources and to determine the different origins of intrusive air mass coming from long-range transport, such as African dust outbreaks and aerosol particles from Central and Eastern Europe. The obtained results were confirmed by applying principal component analysis to the number particle concentration dataset and by the chemical characterization of the samples (PM(10) and PM(2.5)). The integrated approach for PM study suggested in this paper can be useful to support the air quality managers for the development of cost-effective control strategies and the application of more suitable risk management approaches.

A large source of dust missing in Particulate Matter emission inventories? Wind erosion of post-fire landscapes

Directory of Open Access Journals (Sweden)

N.S. Wagenbrenner

2017-02-01

Full Text Available Wind erosion of soils burned by wildfire contributes substantial particulate matter (PM in the form of dust to the atmosphere, but the magnitude of this dust source is largely unknown. It is important to accurately quantify dust emissions because they can impact human health, degrade visibility, exacerbate dust-on-snow issues (including snowmelt timing, snow chemistry, and avalanche danger, and affect ecological and biogeochemical cycles, precipitation regimes, and the Earth’s radiation budget. We used a novel modeling approach in which local-scale winds were used to drive a high-resolution dust emission model parameterized for burned soils to provide a first estimate of post-fire PM emissions. The dust emission model was parameterized with dust flux measurements from a 2010 fire scar. Here we present a case study to demonstrate the ability of the modeling framework to capture the onset and dynamics of a post-fire dust event and then use the modeling framework to estimate PM emissions from burn scars left by wildfires in U.S. western sagebrush landscapes during 2012. Modeled emissions from 1.2 million ha of burned soil totaled 32.1 Tg (11.7–352 Tg of dust as PM10 and 12.8 Tg (4.68–141 Tg as PM2.5. Despite the relatively large uncertainties in these estimates and a number of underlying assumptions, these first estimates of annual post-fire dust emissions suggest that post-fire PM emissions could substantially increase current annual PM estimates in the U.S. National Emissions Inventory during high fire activity years. Given the potential for post-fire scars to be a large source of PM, further on-site PM flux measurements are needed to improve emission parameterizations and constrain these first estimates.

Local contribution of wood combustion to PM10 and PM2.5; Lokale bijdrage van houtverbranding aan PM10 en PM2,5

Energy Technology Data Exchange (ETDEWEB)

Kos, G.; Weijers, E. [ECN Biomassa, Kolen en Milieuonderzoek, Petten (Netherlands)

2011-04-15

In February 2009 the concentration of wood smoke in a residential area in Schoorl (Noord-Holland, Netherlands) was investigated over a period of three weeks. The aim was to assess the effect of local particulate matter (PM) emissions - caused by heating with wood stoves in this area - on local PM concentration. [Dutch] In februari 2009 zijn in Schoorl in Noord-Holland concentraties houtrook bepaald door levoglucosanmetingen (een voor houtrook kenmerkende koolwaterstofverbinding). Lokale houtrook draagt daar significant bij aan de concentratie fijn stof: tussen 9% en 27% voor PM10 en tussen 30% en 39% voor PM2,5.

Characterisation and quantification of the sources of PM10 during air pollution episodes in the UK

International Nuclear Information System (INIS)

Muir, David; Longhurst, J.W.S.; Tubb, A.

2006-01-01

Data for concentrations of PM 10 and gaseous pollutants from sites in the UK Automatic Urban and Rural Network have been examined during periods of elevated concentrations of PM 10 . The ratios of concentrations of PM 10 to those of the other pollutants were used to determine the most probable source of the additional particles. The hypothesis is that because the concentrations of PM 10 were divided by those of the other pollutants, the ratio should decrease when PM 10 and the other pollutants have a common source. Conversely, the ratio should increase when the sources are different. During episodes where road traffic was the most probable source of the additional particles, the ratios of concentrations of PM 10 to carbon monoxide and oxides of nitrogen did decrease, but the comparable ratios for sulphur dioxide and ozone increased. In contrast, during episodes known to have been caused by construction activity, all these ratios increased. This is taken to show that the basic hypothesis is valid. For prolonged episodes, it was possible to use data averaged over the total duration of the episode for the purposes of source identification. For sporadic construction, or other short-duration episodes, it was necessary to use time series data. The data have also been used to calculate the differences between hourly average concentrations of pollutants measured during episodes and long-term hourly average concentrations. These have been used to model the additional PM 10 during air pollution episodes associated with construction activities and road traffic emissions. This confirms the lack of relationship between PM 10 and other pollutants during construction works. During episodes arising from road traffic emissions, there was good agreement between measured and modelled additional concentrations of PM 10 when an appropriate factor, F, related to the contribution of road traffic emissions to PM 10 at different site types was applied. The values used were 0.2 (Suburban

Source apportionment for indoor PM2.5 and elemental concentrations using by a positive matrix factorization and an instrumental neutron activation analysis

International Nuclear Information System (INIS)

Lim, Jong Myoung; Moon, Jong Hwa; Chung, Yong Sam; Jung, Byoung Won; Lee, Jin Hong

2009-01-01

Airborne particulate matters, especially the PM2.5 (aerodynamic equivalent diameter, AED, less than 2.5 μm) fraction has been important. This is because of their potential for deposition on to the human respiratory system being accompanied by many harmful trace metals (such as As, Cd, Cr, Cu, Mn, Pb, Se, and Zn). The indoor air quality has become a great concern since late 1980s, because the population spends a majority of their time in various indoor environments. The indoor particulate matter may be influenced from outdoor environment and indoor sources such as environmental tobacco smoke (ETS), combustion devices, cooking, etc. In this study, we undertake the measurements of about 26 elements using instrumental neutron activation analysis (INAA). Based on our measurement data, we characterize concentration status and mutual relationship between indoor and adjacent outdoor air quality. Next, sources at indoor/outdoor environment were identified and the contributions of each source were quantified by positive matrix factorization (PMF)

A possible link between particulate matter air pollution and type 2 diabetes

NARCIS (Netherlands)

Volders, Evelien

2008-01-01

Particulate matter (PM) air pollution is most commonly referred to as PM10 and can be subdivided into coarse particles, fine particles and ultrafine particles. Sources of PM air pollution include combustion from car engines and industrial processes. Expos

Chemical Composition and Emission Sources of the Fine Particulate Matters in a Southeast Asian Mega City (Dhaka, Bangladesh)

Science.gov (United States)

Salam, Abdus

2016-04-01

Air pollution has significant impact on human health, climate change, agriculture, visibility reduction, and also on the atmospheric chemistry. There are many studies already reported about the direct relation of the human mortality and morbidity with the increase of the atmospheric particulate matters. Especially, fine particulate matters can easily enter into the human respiratory system and causes many diseases. Particulate matters have the properties to absorb the solar radiation and impact on the climate. Dhaka, Bangladesh is a densely populated mega-city in the world. About 16 million inhabitants are living within an area of 360 square kilometers. Air quality situation has been degrading due to unplanned growth, increasing vehicles, severe traffic jams, brick kilns, industries, construction, and also transboundary air pollution. A rapidly growing number of vehicles has worsen the air quality in spite of major policy interventions, e.g., ban of two-stroke and three-wheeled vehicles, phase out of 20 years old vehicles, conversion to compressed natural gas (CNGs), etc. Introduction of CNGs to reduce air pollution was not the solution for fine particles at all, as evidence shows that CNGs and diesel engines are the major sources of fine particles. High concentration of the air pollutants in Dhaka city such as PM, carbonaceous species (black and organic carbon), CO, etc. has already been reported. PM2.5 mass, chemical composition (e.g., BC, OC, SO42-, NO3-, trace elements, etc.), aerosol Optical Depth (AOD) and emission sources of our recent measurements at the highly polluted south East Asian Mega city (Dhaka) Bangladesh will be presented in the conference. PM2.5 samples were collected on filters with Digital PM2.5 sampler (Switzerland) and Air photon, USA. BC was measured from filters (with thermal and optical method) and also real time with an Aethalometer AE42 (Magee Scitific., USA). Water soluble ions were determined from filters with ion chromatogram. AOD

Characteristics of PM2.5 speciation in representative megacities and across China

Science.gov (United States)

Yang, F.; Tan, J.; Zhao, Q.; Du, Z.; He, K.; Ma, Y.; Duan, F.; Chen, G.; Zhao, Q.

2011-06-01

Based on PM2.5 chemical data sets from literature and from our surface observations, chemical species and reconstructed speciation of PM2.5 in representative Chinese megacities and across China were compared to draw insights into the characteristics of PM2.5 speciation. PM2.5 mass concentrations and speciation compositions varied substantially over geographical regions in China. Near six-fold variations in average PM2.5 concentrations (34.0-193.4 μg m-3) across China were found with high PM2.5 levels (>100 μg m-3) appearing in the cities in the northern and western regions and low levels (transport of the secondary aerosols, thus more intensive characteristic of "complex atmospheric pollution" compared to the western region. Organic matter had significant contribution to PM2.5 over all the sites. Organic matter plus sulfate, nitrate, and ammonia accounted for 53-90 % of PM2.5 mass across China. PM2.5 speciation across China was also characterized by high content of crustal material, which was usually at more than ~10 μg m-3 level or shared ~10 % of PM2.5 mass in urban areas, due to transported desert dust and locally induced dust. In four representative megacities (i.e. Beijing, Chongqing, Shanghai, and Guangzhou), PM2.5 mass and major components (except sulfate) were at higher levels than those in US continental east by one order of magnitude. Distinct differences in nitrate and sulfate levels and their mass ratio [NO3-]/[SO42-] imply that mobile sources are likely more important in Guangzhou, whereas in Chongqing it is stationary (coal combustion) sources. The observed intra-city variations in PM2.5 mass and speciation indicate that both local emissions and regional transportation contributed significantly to high fine particle loadings in Beijing, while local contribution likely played a predominant role in Chongqing. During the ten-year period from 1999 through 2008 in urban Beijing, both the sum of sulfate, nitrate, and ammonia and [NO3-]/[SO42-] ratio

Receptor modeling of PM2.5, PM10 and TSP in different seasons and long-range transport analysis at a coastal site of Tianjin, China.

Science.gov (United States)

Kong, Shaofei; Han, Bin; Bai, Zhipeng; Chen, Li; Shi, Jianwu; Xu, Zhun

2010-09-15

Atmospheric particulate matter (PM(2.5), PM(10) and TSP) were sampled synchronously during three monitoring campaigns from June 2007 to February 2008 at a coastal site in TEDA of Tianjin, China. Chemical compositions including 19 elements, 6 water-solubility ions, organic and elemental carbon were determined. principle components analysis (PCA) and chemical mass balance modeling (CMB) were applied to determine the PM sources and their contributions with the assistance of NSS SO(4)(2)(-), the mass ratios of NO(3)(-) to SO(4)(2)(-) and OC to EC. Air mass backward trajectory model was compared with source apportionment results to evaluate the origin of PM. Results showed that NSS SO(4)(2)(-) values for PM(2.5) were 2147.38, 1701.26 and 239.80 ng/m(3) in summer, autumn and winter, reflecting the influence of sources from local emissions. Most of it was below zero in summer for PM(10) indicating the influence of sea salt. The ratios of NO(3)(-) to SO(4)(2)(-) was 0.19 for PM(2.5), 0.18 for PM(10) and 0.19 for TSP in winter indicating high amounts of coal consumed for heating purpose. Higher OC/EC values (mostly larger than 2.5) demonstrated that secondary organic aerosol was abundant at this site. The major sources were construction activities, road dust, vehicle emissions, marine aerosol, metal manufacturing, secondary sulfate aerosols, soil dust, biomass burning, some pharmaceutics industries and fuel-oil combustion according to PCA. Coal combustion, marine aerosol, vehicular emission and soil dust explained 5-31%, 1-13%, 13-44% and 3-46% for PM(2.5), PM(10) and TSP, respectively. Backward trajectory analysis showed air parcels originating from sea accounted for 39% in summer, while in autumn and winter the air parcels were mainly related to continental origin. Copyright 2010 Elsevier B.V. All rights reserved.

Sources of the PM10 aerosol in Flanders, Belgium, and re-assessment of the contribution from wood burning

International Nuclear Information System (INIS)

Maenhaut, Willy; Vermeylen, Reinhilde; Claeys, Magda; Vercauteren, Jordy; Roekens, Edward

2016-01-01

From 30 June 2011 to 2 July 2012 PM10 aerosol samples were simultaneously taken every 4th day at four urban background sites in Flanders, Belgium. The sites were in Antwerpen, Gent, Brugge, and Oostende. The PM10 mass concentration was determined by weighing; organic and elemental carbon (OC and EC) were measured by thermal-optical analysis, the wood burning tracers levoglucosan, mannosan and galactosan were determined by gas chromatography/mass spectrometry, 8 water-soluble ions were measured by ion chromatography, and 15 elements were determined by a combination of inductively coupled plasma atomic emission spectrometry and mass spectrometry. The multi-species dataset was subjected to receptor modeling by PMF. The 10 retained factors (with their overall average percentage contributions to the experimental PM10 mass) were wood burning (9.5%), secondary nitrate (24%), secondary sulfate (12.6%), sea salt (10.0%), aged sea salt (19.2%), crustal matter (9.7%), non-ferrous metals (1.81%), traffic (10.3%), non-exhaust traffic (0.52%), and heavy oil burning (3.0%). The average contributions of wood smoke for the four sites were quite substantial in winter and ranged from 12.5 to 20% for the PM10 mass and from 47 to 64% for PM10 OC. Wood burning appeared to be also a notable source of As, Cd, and Pb. The contribution from wood burning to the PM10 mass and OC was also assessed by making use of levoglucosan as single marker compound and the conversion factors of Schmidl et al. (2008), as done in our previous study on wood burning in Flanders (Maenhaut et al., 2012). However, the apportionments were much lower than those deduced from PMF. It seems that the conversion factors of Schmidl et al. (2008) may not be applicable to wood burning in Flanders. From scatter plots of the PMF-derived wood smoke OC and PM versus levoglucosan, we arrived at conversion factors of 9.7 and 22.6, respectively. - Highlights: • A one-year study with 4 urban background sites and a total of 372

Sources of the PM10 aerosol in Flanders, Belgium, and re-assessment of the contribution from wood burning

Energy Technology Data Exchange (ETDEWEB)

Maenhaut, Willy, E-mail: willy.maenhaut@ugent.be [Ghent University (UGent), Department of Analytical Chemistry, Krijgslaan 281, S12, B-9000 Gent (Belgium); University of Antwerp - UA, Department of Pharmaceutical Sciences, Universiteitsplein 1, B-2610, Antwerpen (Belgium); Vermeylen, Reinhilde; Claeys, Magda [University of Antwerp - UA, Department of Pharmaceutical Sciences, Universiteitsplein 1, B-2610, Antwerpen (Belgium); Vercauteren, Jordy; Roekens, Edward [Flemish Environment Agency (VMM), Kronenburgstraat 45, B-2000, Antwerpen (Belgium)

2016-08-15

From 30 June 2011 to 2 July 2012 PM10 aerosol samples were simultaneously taken every 4th day at four urban background sites in Flanders, Belgium. The sites were in Antwerpen, Gent, Brugge, and Oostende. The PM10 mass concentration was determined by weighing; organic and elemental carbon (OC and EC) were measured by thermal-optical analysis, the wood burning tracers levoglucosan, mannosan and galactosan were determined by gas chromatography/mass spectrometry, 8 water-soluble ions were measured by ion chromatography, and 15 elements were determined by a combination of inductively coupled plasma atomic emission spectrometry and mass spectrometry. The multi-species dataset was subjected to receptor modeling by PMF. The 10 retained factors (with their overall average percentage contributions to the experimental PM10 mass) were wood burning (9.5%), secondary nitrate (24%), secondary sulfate (12.6%), sea salt (10.0%), aged sea salt (19.2%), crustal matter (9.7%), non-ferrous metals (1.81%), traffic (10.3%), non-exhaust traffic (0.52%), and heavy oil burning (3.0%). The average contributions of wood smoke for the four sites were quite substantial in winter and ranged from 12.5 to 20% for the PM10 mass and from 47 to 64% for PM10 OC. Wood burning appeared to be also a notable source of As, Cd, and Pb. The contribution from wood burning to the PM10 mass and OC was also assessed by making use of levoglucosan as single marker compound and the conversion factors of Schmidl et al. (2008), as done in our previous study on wood burning in Flanders (Maenhaut et al., 2012). However, the apportionments were much lower than those deduced from PMF. It seems that the conversion factors of Schmidl et al. (2008) may not be applicable to wood burning in Flanders. From scatter plots of the PMF-derived wood smoke OC and PM versus levoglucosan, we arrived at conversion factors of 9.7 and 22.6, respectively. - Highlights: • A one-year study with 4 urban background sites and a total of 372

PM2.5 in Dutch dwellings due to cooking

NARCIS (Netherlands)

Jacobs, P.; Borsboom, W.A.; Kemp, R.E.J.

2016-01-01

Cooking emissions have long been seen as an odour problem. However recent studies showed that Particulate Matter (PM) is the main health risk of indoor air and cooking can be a major source. A small field study within 9 Dutch dwellings indicates that depending on the conditions cooking can have a

Chemical characterization of PM1.0 aerosol in Delhi and source apportionment using positive matrix factorization.

Science.gov (United States)

Jaiprakash; Singhai, Amrita; Habib, Gazala; Raman, Ramya Sunder; Gupta, Tarun

2017-01-01

Fine aerosol fraction (particulate matter with aerodynamic diameter <= 1.0 μm (PM) 1.0 ) over the Indian Institute of Technology Delhi campus was monitored day and night (10 h each) at 30 m height from November 2009 to March 2010. The samples were analyzed for 5 ions (NH 4 + , NO 3 - , SO 4 2- , F - , and Cl - ) and 12 trace elements (Na, K, Mg, Ca, Pb, Zn, Fe, Mn, Cu, Cd, Cr, and Ni). Importantly, secondary aerosol (sulfate and nitrate) formation was observed during dense foggy events, supporting the fog-smog-fog cycle. A total of 76 samples were used for source apportionment of PM mass. Six factors were resolved by PMF analyses and were identified as secondary aerosol, secondary chloride, biomass burning, soil dust, iron-rich source, and vehicular emission. The geographical location of the sources and/or preferred transport pathways was identified by conditional probability function (for local sources) and potential source contribution function (for regional sources) analyses. Medium- and small-scale metal processing (e.g. steel sheet rolling) industries in Haryana and National Capital Region (NCR) Delhi, coke and petroleum refining in Punjab, and thermal power plants in Pakistan, Punjab, and NCR Delhi were likely contributors to secondary sulfate, nitrate, and secondary chloride at the receptor site. The agricultural residue burning after harvesting season (Sept-Dec and Feb-Apr) in Punjab, and Haryana contributed to potassium at receptor site during November-December and March 2010. The soil dust from North and East Pakistan, and Rajasthan, North-East Punjab, and Haryana along with the local dust contributed to soil dust at the receptor site, during February and March 2010. A combination of temporal behavior and air parcel trajectory ensemble analyses indicated that the iron-rich source was most likely a local source attributed to emissions from metal processing facilities. Further, as expected, the vehicular emissions source did not show any seasonality and

Characteristics of PM10 Chemical Source Profiles for Geological Dust from the South-West Region of China

Directory of Open Access Journals (Sweden)

Yayong Liu

2016-11-01

Full Text Available Ninety-six particulate matter (PM10 chemical source profiles for geological sources in typical cities of southwest China were acquired from Source Profile Shared Service in China. Twenty-six elements (Na, Mg, Al, Si, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Sr, Cd, Sn, Sb, Ba, Be, Tl and Pb, nine ions (F−, Cl−, SO42−, NO3−, Na+, NH4+, K+, Mg2+ and Ca2+, and carbon-containing species (organic carbon and elemental carbon were determined to construct these profiles. Individual source profiles were averaged and compared to quantify similarities and differences in chemical abundances using the profile-compositing method. Overall, the major components of PM10 in geological sources were crustal minerals and undefined fraction. Different chemical species could be used as tracers for various types of geological dust in the region that resulted from different anthropogenic influence. For example, elemental carbon, V and Zn could be used as tracers for urban paved road dust; Al, Si, K+ and NH4+ for agricultural soil; Al and Si for natural soil; and SO42− for urban resuspended dust. The enrichment factor analysis showed that Cu, Se, Sr and Ba were highly enriched by human activities in geological dust samples from south-west China. Elemental ratios were taken to highlight the features of geological dust from south-west China by comparing with northern urban fugitive dust, loess and desert samples. Low Si/Al and Fe/Al ratios can be used as markers to trace geological sources from southwestern China. High Pb/Al and Zn/Al ratios observed in urban areas demonstrated that urban geological dust was influenced seriously by non-crustal sources.

Source contributions to PM2.5 in Guangdong province, China by numerical modeling: Results and implications

Science.gov (United States)

Yin, Xiaohong; Huang, Zhijiong; Zheng, Junyu; Yuan, Zibing; Zhu, Wenbo; Huang, Xiaobo; Chen, Duohong

2017-04-01

As one of the most populous and developed provinces in China, Guangdong province (GD) has been experiencing regional haze problems. Identification of source contributions to ambient PM2.5 level is essential for developing effective control strategies. In this study, using the most up-to-date emission inventory and validated numerical model, source contributions to ambient PM2.5 from eight emission source sectors (agriculture, biogenic, dust, industry, power plant, residential, mobile and others) in GD in 2012 were quantified. Results showed that mobile sources are the dominant contributors to the ambient PM2.5 (24.0%) in the Pearl River Delta (PRD) region, the central and most developed area of GD, while industry sources are the major contributors (21.5% 23.6%) to those in the Northeastern GD (NE-GD) region and the Southwestern GD (SW-GD) region. Although many industries have been encouraged to move from the central GD to peripheral areas such as NE-GD and SW-GD, their emissions still have an important impact on the PM2.5 level in the PRD. In addition, agriculture sources are responsible for 17.5% to ambient PM2.5 in GD, indicating the importance of regulations on agricultural activities, which has been largely ignored in the current air quality management. Super-regional contributions were also quantified and their contributions to the ambient PM2.5 in GD are significant with notable seasonal differences. But they might be overestimated and further studies are needed to better quantify the transport impacts.

Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE): Emissions of particulate matter from wood and dung cooking fires, brick kilns, generators, trash and crop residue burning

Science.gov (United States)

Stone, Elizabeth; Jayarathne, Thilina; Stockwell, Chelsea; Christian, Ted; Bhave, Prakash; Siva Praveen, Puppala; Panday, Arnico; Adhikari, Sagar; Maharjan, Rashmi; Goetz, Doug; DeCarlo, Peter; Saikawa, Eri; Yokelson, Robert

2016-04-01

The Nepal Ambient Monitoring and Source Testing Experiment (NAMASTE) field campaign targeted the in situ characterization of widespread and under-sampled combustion sources. In Kathmandu and the Terai, southern Nepal's flat plains, samples of fine particulate matter (PM2.5) were collected from wood and dung cooking fires (n = 22), generators (n = 2), groundwater pumps (n = 2), clamp kilns (n = 3), zig-zag kilns (n = 3), trash burning (n = 4), one heating fire, and one crop residue fire. Co-located measurements of carbon dioxide, carbon monoxide, and volatile organic compounds allowed for the application of the carbon mass balance approach to estimate emission factors for PM2.5, elemental carbon, organic carbon, and water-soluble inorganic ions. Organic matter was chemically speciated using gas chromatography - mass spectrometry for polycyclic aromatic hydrocarbons, sterols, n-alkanes, hopanes, steranes, and levoglucosan, which accounted for 2-8% of the measured organic carbon. These data were used to develop molecular-marker based profiles for use in source apportionment modeling. This study provides quantitative emission factors for particulate matter and its constituents for many important combustion sources in Nepal and South Asia.

Black carbon and particulate matter (PM2.5) concentrations in New York City's subway stations.

Science.gov (United States)

Vilcassim, M J Ruzmyn; Thurston, George D; Peltier, Richard E; Gordon, Terry

2014-12-16

The New York City (NYC) subway is the main mode of transport for over 5 million passengers on an average weekday. Therefore, airborne pollutants in the subway stations could have a significant impact on commuters and subway workers. This study looked at black carbon (BC) and particulate matter (PM2.5) concentrations in selected subway stations in Manhattan. BC and PM2.5 levels were measured in real time using a Micro-Aethalometer and a PDR-1500 DataRAM, respectively. Simultaneous samples were also collected on quartz filters for organic and elemental carbon (OC/EC) analysis and on Teflon filters for gravimetric and trace element analysis. In the underground subway stations, mean real time BC concentrations ranged from 5 to 23 μg/m(3), with 1 min average peaks >100 μg/m(3), while real time PM2.5 levels ranged from 35 to 200 μg/m(3). Mean EC levels ranged from 9 to 12.5 μg/m(3). At street level on the same days, the mean BC and PM2.5 concentrations were below 3 and 10 μg/m(3), respectively. This study shows that both BC soot and PM levels in NYC's subways are considerably higher than ambient urban street levels and that further monitoring and investigation of BC and PM subway exposures are warranted.

Spatiotemporal variations of ambient PM10 source contributions in Beijing in 2004 using positive matrix factorization

Directory of Open Access Journals (Sweden)

T. Chen

2008-05-01

Full Text Available Source contributions to ambient PM10 (particles with an aerodynamic diameter of 10 μm or less in Beijing, China were determined with positive matrix factorization (PMF based on ambient PM10 composition data including concentrations of organic carbon (OC, elemental carbon (EC, ions and metal elements, which were simultaneously obtained at six sites through January, April, July and October in 2004. Results from PMF indicated that seven major sources of ambient PM10 were urban fugitive dust, crustal soil, coal combustion, secondary sulfate, secondary nitrate, biomass burning with municipal incineration, and vehicle emission, respectively. In paticular, urban fugitive dust and crustal soil as two types of dust sources with similar chemical characteristics were differentiated by PMF. Urban fugitive dust contributed the most, accounting for 34.4% of total PM10 mass on an annual basis, with relatively high contributions in all four months, and even covered 50% in April. It also showed higher contributions in southwestern and southeastern areas than in central urban areas. Coal combustion was found to be the primary contributor in January, showing higher contributions in urban areas than in suburban areas with seasonal variation peaking in winter, which accounted for 15.5% of the annual average PM10 concentration. Secondary sulfate and secondary nitrate combined as the largest contributor to PM10 in July and October, with strong seasonal variation peaking in summer, accounting for 38.8% and 31.5% of the total PM10 mass in July and October, respectively. Biomass burning with municipal incineration contributions were found in all four months and accounted for 9.8% of the annual average PM10 mass concentration, with obviously higher contribution in October than in other months. Incineration sources were probably located in southwestern Beijing. Contribution from vehicle emission accounted for 5.0% and exhibited no significant seasonal variation. In sum

Oxidative potential of subway PM2.5

Science.gov (United States)

Moreno, Teresa; Kelly, Frank J.; Dunster, Chrissi; Oliete, Ana; Martins, Vânia; Reche, Cristina; Minguillón, Maria Cruz; Amato, Fulvio; Capdevila, Marta; de Miguel, Eladio; Querol, Xavier

2017-01-01

Air quality in subway systems is of interest not only because particulate matter (PM) concentrations can be high, but also because of the peculiarly metalliferous chemical character of the particles, most of which differ radically from those of outdoor ambient air. We report on the oxidative potential (OP) of PM2.5 samples collected in the Barcelona subway system in different types of stations. The PM chemical composition of these samples showed typically high concentrations of Fe, Total Carbon, Ba, Cu, Mn, Zn and Cr sourced from rail tracks, wheels, catenaries, brake pads and pantographs. Two toxicological indicators of oxidative activity, ascorbic acid (AA) oxidation (expressed as OPAA μg-1 or OPAA m-3) and glutathione (GSH) oxidation (expressed as OPGSH μg-1 or OPGSH m-3), showed low OP for all samples (compared with outdoor air) but considerable variation between stations (0.9-2.4 OPAA μg-1; 0.4-1.9 OPGSH μg-1). Results indicate that subway PM toxicity is not related to variations in PM2.5 concentrations produced by ventilation changes, tunnel works, or station design, but may be affected more by the presence of metallic trace elements such as Cu and Sb sourced from brakes and pantographs. The OP assays employed do not reveal toxic effects from the highly ferruginous component present in subway dust.

Particulate Matter 2.5 Exposure and Self-Reported Use of Wood Stoves and Other Indoor Combustion Sources in Urban Nonsmoking Homes in Norway.

Directory of Open Access Journals (Sweden)

Annah B Wyss

Full Text Available Few studies have examined particulate matter (PM exposure from self-reported use of wood stoves and other indoor combustion sources in urban settings in developed countries. We measured concentrations of indoor PM < 2.5 microns (PM2.5 for one week with the MicroPEM™ nephelometer in 36 households in the greater Oslo, Norway metropolitan area. We examined indoor PM2.5 levels in relation to use of wood stoves and other combustion sources during a 7 day monitoring period using mixed effects linear models with adjustment for ambient PM2.5 levels. Mean hourly indoor PM2.5 concentrations were higher (p = 0.04 for the 14 homes with wood stove use (15.6 μg/m3 than for the 22 homes without (12.6 μg/m3. Moreover, mean hourly PM2.5 was higher (p = 0.001 for use of wood stoves made before 1997 (6 homes, 20.2 μg/m3, when wood stove emission limits were instituted in Norway, compared to newer wood stoves (8 homes, 11.9 μg/m3 which had mean hourly values similar to control homes. Increased PM2.5 levels during diary-reported burning of candles was detected independently of concomitant wood stove use. These results suggest that self-reported use of wood stoves, particularly older stoves, and other combustion sources, such as candles, are associated with indoor PM2.5 measurements in an urban population from a high income country.

The local contribution of wood burning to PM10 and PM2.5; De lokale bijdrage van houtverbranding aan PM10 en PM2,5

Energy Technology Data Exchange (ETDEWEB)

Kos, G.; Weijers, E. [ECN Biomassa, Kolen en Milieuonderzoek, Petten (Netherlands)

2011-04-15

In January 2009, the concentrations of wood smoke in Schoorl, the Netherlands, were established by means of levoglucosan measurements (a hydrocarbon compound that is characteristic for wood smoke). Local wood smoke contributes significantly to the concentration of particulate matter: between 9% and 27% for PM10 and between 30% and 29% for PM2.5. [Dutch] In februari 2009 zijn in Schoorl in Noord-Holland concentraties houtrook bepaald door levoglucosanmetingen (een voor houtrook kenmerkende koolwaterstofverbinding). Lokale houtrook draagt daar significant bij aan de concentratie fijn stof: tussen 9% en 27% voor PM10 en tussen 30% en 39% voor PM2,5.

Partitioning of magnetic particles in PM10, PM2.5 and PM1 aerosols in the urban atmosphere of Barcelona (Spain).

Science.gov (United States)

Revuelta, María Aránzazu; McIntosh, Gregg; Pey, Jorge; Pérez, Noemi; Querol, Xavier; Alastuey, Andrés

2014-05-01

A combined magnetic-chemical study of 15 daily, simultaneous PM10-PM2.5-PM1 urban background aerosol samples has been carried out. The magnetic properties are dominated by non-stoichiometric magnetite, with highest concentrations seen in PM10. Low temperature magnetic analyses showed that the superparamagnetic fraction is more abundant when coarse, multidomain particles are present, confirming that they may occur as an oxidized outer shell around coarser grains. A strong association of the magnetic parameters with a vehicular PM10 source has been identified. Strong correlations found with Cu and Sb suggests that this association is related to brake abrasion emissions rather than exhaust emissions. For PM1 the magnetic remanence parameters are more strongly associated with crustal sources. Two crustal sources are identified in PM1, one of which is of North African origin. The magnetic particles are related to this source and so may be used to distinguish North African dust from other sources in PM1. Copyright © 2014 Elsevier Ltd. All rights reserved.

Statins attenuate the development of atherosclerosis and endothelial dysfunction induced by exposure to urban particulate matter (PM{sub 10})

Energy Technology Data Exchange (ETDEWEB)

Miyata, Ryohei; Hiraiwa, Kunihiko; Cheng, Jui Chih [UBC James Hogg Research Centre, St. Paul' s Hospital, University of British Columbia, Vancouver (Canada); Bai, Ni [UBC James Hogg Research Centre, St. Paul' s Hospital, University of British Columbia, Vancouver (Canada); Department of Anesthesiology, Pharmacology and Therapeutics, University of British Columbia, Vancouver (Canada); Vincent, Renaud [Environmental Health Sciences and Research Bureau, Healthy Environments and Consumer Safety Branch, Health Canada, Ottawa (Canada); Francis, Gordon A.; Sin, Don D. [UBC James Hogg Research Centre, St. Paul' s Hospital, University of British Columbia, Vancouver (Canada); Van Eeden, Stephan F., E-mail: Stephan.vanEeden@hli.ubc.ca [UBC James Hogg Research Centre, St. Paul' s Hospital, University of British Columbia, Vancouver (Canada)

2013-10-01

Exposure to ambient air particulate matter (particles less than 10 μm or PM{sub 10}) has been shown to be an independent risk factor for the development and progression of atherosclerosis. The 3-hydroxy-3-methylglutaryl coenzyme A reductase inhibitors (statins) have well-established anti-inflammatory properties. The aim of this study was to determine the impact of statins on the adverse functional and morphological changes in blood vessels induced by PM{sub 10}. New Zealand White rabbits fed with a high fat diet were subjected to balloon injury to their abdominal aorta followed by PM{sub 10}/saline exposure for 4 weeks ± lovastatin (5 mg/kg/day) treatment. PM{sub 10} exposure accelerated balloon catheter induced plaque formation and increased intimal macrophages and lipid accumulation while lovastatin attenuated these changes and promoted smooth muscle cell recruitment into plaques. PM{sub 10} impaired vascular acetylcholine (Ach) responses and increased vasoconstriction induced by phenylephrine as assessed by wire myograph. Supplementation of nitric oxide improved the impaired Ach responses. PM{sub 10} increased the expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2) in blood vessels and increased the plasma levels of endothelin-1 (ET-1). Incubation with specific inhibitors for iNOS, COX-2 or ET-1 in the myograph chambers significantly improved the impaired vascular function. Lovastatin decreased the expression of these mediators in atherosclerotic lesions and improved endothelial dysfunction. However, lovastatin was unable to reduce blood lipid levels to the baseline level in rabbits exposed to PM{sub 10}. Taken together, statins protect against PM{sub 10}-induced cardiovascular disease by reducing atherosclerosis and improving endothelial function via their anti-inflammatory properties. - Highlights: • Coarse particulate matter (PM{sub 10}) accelerated balloon injury-induced plaque formation. • Lovastatin decreased intimal

RESPIRATORY EFFECTS OF INHALED METAL-RICH PARTICULATE MATTER (PM) IN RATS: INFLUENCE OF SYSTEMIC ANTIOXIDANT DEPLETION

Science.gov (United States)

Metal-mediated generation of reactive oxygen species and resultant oxidative stress has been implicated in the pathogenesis of emission-source PM toxicity. We hypothesized that inducing an antioxidant deficit prior to inhalation of metal-rich PM would worsen adverse health outcom...

Household Air Pollution: Sources and Exposure Levels to Fine Particulate Matter in Nairobi Slums

Directory of Open Access Journals (Sweden)

Kanyiva Muindi

2016-07-01

Full Text Available With 2.8 billion biomass users globally, household air pollution remains a public health threat in many low- and middle-income countries. However, little evidence on pollution levels and health effects exists in low-income settings, especially slums. This study assesses the levels and sources of household air pollution in the urban slums of Nairobi. This cross-sectional study was embedded in a prospective cohort of pregnant women living in two slum areas—Korogocho and Viwandani—in Nairobi. Data on fuel and stove types and ventilation use come from 1058 households, while air quality data based on the particulate matters (PM2.5 level were collected in a sub-sample of 72 households using the DustTrak™ II Model 8532 monitor. We measured PM2.5 levels mainly during daytime and using sources of indoor air pollutions. The majority of the households used kerosene (69.7% as a cooking fuel. In households where air quality was monitored, the mean PM2.5 levels were high and varied widely, especially during the evenings (124.6 µg/m3 SD: 372.7 in Korogocho and 82.2 µg/m3 SD: 249.9 in Viwandani, and in households using charcoal (126.5 µg/m3 SD: 434.7 in Korogocho and 75.7 µg/m3 SD: 323.0 in Viwandani. Overall, the mean PM2.5 levels measured within homes at both sites (Korogocho = 108.9 µg/m3 SD: 371.2; Viwandani = 59.3 µg/m3 SD: 234.1 were high. Residents of the two slums are exposed to high levels of PM2.5 in their homes. We recommend interventions, especially those focusing on clean cookstoves and lighting fuels to mitigate indoor levels of fine particles.

SOURCE SAMPLING FINE PARTICULATE MATTER: WOOD-FIRED INDUSTRIAL BOILER

Science.gov (United States)

The report provides a profile for a wood-fired industrial boiler equipped with a multistage electrostatic precipitator control device. Along with the profile of emissions of fine particulate matter of aerodynamic diameter of 2.5 micrometers or less (PM-2.5), data are also provide...

Factors influencing mobile source particulate matter emissions-to-exposure relationships in the Boston urban area.

Science.gov (United States)

Greco, Susan L; Wilson, Andrew M; Hanna, Steven R; Levy, Jonathan I

2007-11-15

Benefit-cost and regulatory impact analyses often use atmospheric dispersion models with coarse resolution to estimate the benefits of proposed mobile source emission control regulations. This approach may bias health estimates or miss important intra-urban variability for primary air pollutants. In this study, we estimate primary fine particulate matter (PM2.5) intake fractions (iF; the fraction of a pollutant emitted from a source that is inhaled by the population) for each of 23 398 road segments in the Boston Metro Core area to evaluate the potential for intra-urban variability in the emissions-to-exposure relationship. We estimate iFs using the CAL3QHCR line source model combined with residential populations within 5000 m of each road segment. The annual average values for the road segments range from 0.8 to 53 per million, with a mean of 12 per million. On average, 46% of the total exposure is realized within 200 m of the road segment, though this varies from 0 to 93% largely due to variable population patterns. Our findings indicate the likelihood of substantial intra-urban variability in mobile source primary PM2.5 iF that accounting for population movement with time, localized meteorological conditions, and street-canyon configurations would likely increase.

Seasonal variation, risk assessment and source estimation of PM 10 and PM10-bound PAHs in the ambient air of Chiang Mai and Lamphun, Thailand.

Science.gov (United States)

Pengchai, Petch; Chantara, Somporn; Sopajaree, Khajornsak; Wangkarn, Sunanta; Tengcharoenkul, Urai; Rayanakorn, Mongkon

2009-07-01

Daily PM10 concentrations were measured at four sampling stations located in Chiang Mai and Lamphun provinces, Thailand. The sampling scheme was conducted during June 2005 to June 2006; every 3 days for 24 h in each sampling period. The result revealed that all stations shared the same pattern, in which the PM10 (particulate matters with diameter of less than 10 microm) concentration increased at the beginning of dry season (December) and reached its peak in March before decreasing by the end of April. The maximum PM10 concentration for each sampling station was in the range of 140-182 microg/m(3) which was 1.1-1.5 times higher than the Thai ambient air quality standard of 120 microg/m(3). This distinctly high concentration of PM10 in the dry season (Dec. 05-Mar. 06) was recognized as a unique seasonal pattern for the northern part of Thailand. PM10 concentration had a medium level of negative correlation (r = -0.696 to -0.635) with the visibility data. Comparing the maximum PM10 concentration detected at each sampling station to the permitted PM10 level of the national air quality standard, the warning visibility values for the PM10 pollution-watch system were determined as 10 km for Chiang Mai Province and 5 km for Lamphun Province. From the analysis of PM10 constituents, no component exceeded the national air quality standard. The total concentrations of PM10-bond polycyclic aromatic hydrocarbons (PAHs) are calculated in terms of total toxicity equivalent concentrations (TTECs) using the toxicity equivalent factors (TEFs) method. TTECs in Chiang Mai and Lamphun ambient air was found at a level comparable to those observed in Nagasaki, Bangkok and Rome and at a lower level than those reported at Copenhagen. The annual number of lung cancer cases for Chiang Mai and Lamphun Provinces was estimated at two cases/year which was lower than the number of cases in Bangkok (27 cases/year). The principal component analysis/absolute principal component scores (PCA

Geochemistry and carbon isotopic ratio for assessment of PM10 composition, source and seasonal trends in urban environment.

Science.gov (United States)

Di Palma, A; Capozzi, F; Agrelli, D; Amalfitano, C; Giordano, S; Spagnuolo, V; Adamo, P

2018-08-01

Investigating the nature of PM 10 is crucial to differentiate sources and their relative contributions. In this study we compared the levels, and the chemical and mineralogical properties of PM 10 particles sampled in different seasons at monitoring stations representative of urban background, urban traffic and suburban traffic areas of Naples city. The aims were to relate the PM 10 load and characteristics to the location of the monitoring stations, to investigate the different sources contributing to PM 10 and to highlight PM 10 seasonal variability. Bulk analyses of chemical species in the PM 10 fraction included total carbon and nitrogen, δ 13 C and other 20 elements. Both natural and anthropogenic sources were found to contribute to the exceedances of the EU PM 10 limit values. The natural contribution was mainly related to marine aerosols and soil dust, as highlighted by X-ray diffractometry and SEM-EDS microscopy. The percentage of total carbon suggested a higher contribution of biogenic components to PM 10 in spring. However, this result was not supported by the δ 13 C values which were seasonally homogeneous and not sufficient to extract single emission sources. No significant differences, in terms of PM 10 load and chemistry, were observed between monitoring stations with different locations, suggesting a homogeneous distribution of PM 10 on the studied area in all seasons. The anthropogenic contribution to PM 10 seemed to dominate in all sites and seasons with vehicular traffic acting as a main source mostly by generation of non-exhaust emissions Our findings reinforce the need to focus more on the analysis of PM 10 in terms of quality than of load, to reconsider the criteria for the classification and the spatial distribution of the monitoring stations within urban and suburban areas, with a special attention to the background location, and to emphasize all the policies promoting sustainable mobility and reduction of both exhaust and not

IDENTIFICATION OF POSSIBLE SOURCES OF PARTICULATE MATTER IN THE PERSONAL CLOUD USING SEM/EDX

Science.gov (United States)

The United States Environmental Protection Agency (U.S. EPA) conducted the Baltimore Particulate Matter (PM) Epidemiology-Exposure Study of the Elderly during the summer of 1998. The study design included PM2.5 samples obtained from elderly (65+ years of age) retirement facility ...

Source contributions to United States ozone and particulate matter over five decades from 1970 to 2020

Science.gov (United States)

Nopmongcol, Uarporn; Alvarez, Yesica; Jung, Jaegun; Grant, John; Kumar, Naresh; Yarwood, Greg

2017-10-01

Evaluating long-term air quality trends can demonstrate effectiveness of control strategies and guide future air quality management planning. Observations have shown that ozone (O3) and fine particulate matter (PM2.5) in the US have declined since as early as 1980 in some areas. But observation trends alone cannot separate effects of changes in local and global emissions to US air quality which are important to air quality planners. This study uses a regional model (CAMx) nested within a global model (GEOS-Chem) to characterize regional changes in O3 and PM2.5 due to the intercontinental transport and local/regional emissions representing six modeling years within five decades (1970-2020). We use the CAMx Source Apportionment Technology (OSAT/PSAT) to estimate contributions from 6 source sectors in 7 source regions plus 6 other groups for a total of 48 tagged contributions. On-road mobile sources consistently make the largest U.S. anthropogenic emissions contribution to O3 in all cities examined even though they decline substantially from 1970 to 2005 and also from 2005 to 2020. Off-road mobile source contributions increase from 1970 to 2005 and then decrease after 2005 in all of the cities. The boundary conditions, mostly from intercontinental transport, contribute more than 20 ppb to high maximum daily 8-h average (MDA8) O3 for all six years. We found that lowering NOx emissions raises O3 formation efficiency (OFE) across all emission categories which will limit potential O3 benefits of local NOx strategies in the near future. PM2.5 benefited from adoption of control devices between 1970 and 1980 and has continued to decline through 2005 and expected to decline further by 2020. Area sources such as residential, commercial and fugitive dust emissions stand out as making large contributions to PM2.5 that are not declining. Inter-regional transport is less important in 2020 than 1990 for both pollutants.

Source of Personal Exposure to PM2.5 among College Students in Beijing, China

Science.gov (United States)

Xie, Qiaorong; Zhu, Xianlei; Li, Xiang; Hui, Fan; Fu, Xianqiang; Zhang, Qiangbin

2015-04-01

The health risk from exposure to airborne particles arouses increasing public concern in Beijing, a megacity in China, where concentration of PM2.5 frequently exceeds the guideline values of World Health Organization (WHO). To investigate daily exposure to PM2.5, a personal exposure study was conducted for college students. The purpose of this study was to measure the daily PM2.5 personal exposures of students, to quantify the contributions of various microenvironments to personal exposure since students spend more than 85% of their time indoors, and to apportion the contributions of PM2.5 indoors origin and outdoor origin. In this work, a total of 320 paired indoor and outdoor PM2.5 samples were collected at eight types of microenvironments in both China University of Petroleum (suburban area) and Tsinghua University (urban area). The microenvironments were selected based on the time-activity diary finished by 1500 students from both universities. Simultaneously, the air exchange rate was measured in each microenvironment. PM2.5, elements, inorganic ions and polycyclic aromatic hydrocarbons in the samples were determined. The peak concentrations were observed in dinning halls, whereas PM2.5 in dormitories was the largest contributor to personal exposure because students spend more than half of a day there. Furthermore, source apportionment by positive matrix factorization (PMF) will be carried out to understand the source of personal exposure to PM2.5. Especially, efforts will be put on determing the contributions of primary combustion, secondary sulfate and organics, secondary nitrate, and mechanically generated PM, which present different infiltration behavior and are indoor PM2.5 of ambient origin, with help of air exchange rate data. The results would be benefit for refining the understanding of the contribution of PM2.5 of ambient (outdoor) origin to the daily PM2.5 personal exposures. Acknowledgments:This study has been funded by Beijing Municipal Commission

Pollution sources for indoor PM2.5 at the platform in subway station using a positive matrix factorization and an instrumental neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Lim, Jong Myoung; Moon, Jong Hwa; Chung, Yong Sam [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Jin Hong [Chungnam National University, Daejeon (Korea, Republic of)

2010-05-15

Airborne particulate matters, especially the PM2.5 (aerodynamic equivalent diameter, AED, less than 2.5 )m) fraction has been important. This is because of their potential for deposition on to the human respiratory system being accompanied by many harmful trace metals (such as As, Cd, Cr, Cu, Mn, Pb, Se, and Zn). As most people spend more than 80% of their time indoors, indoor air quality (IAQ) can exert a considerable impact on the inhalation condition of toxic substances. Therefore, assessment of the absolute concentration levels and elemental composition of PM in an indoor environment such as subway station can be used as a practical barometer of IAQ. The contaminants originated from the indoor pollution sources as well as various outdoor sources are easily accumulated in indoor environment dissimilar to the outdoor. Especially, since the natural ventilation is nearly impossible in the subway station, its pollution status can be worsened under the circumstance that contaminants are constantly originated and circulated inside of station by the repetitive action of subway trains. In this study, a total of 60 PM2.5 samples were collected for 4 seasonal campaigns in 2009 with a low-volume air sampler at one subway station in Daejeon, Korea. We undertook the measurements of up to 25 elements in PM2.5 using an instrumental neutron activation analysis (INAA) and X-ray fluorescence (XRF). And inorganic ion species (SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, NH{sub 4}{sup +}) also were determined by ion chromatography (IC). Next, sources at indoor/outdoor environment were identified and the contributions of each source were quantified by positive matrix factorization (PMF).

Pollution sources for indoor PM2.5 at the platform in subway station using a positive matrix factorization and an instrumental neutron activation analysis

International Nuclear Information System (INIS)

Lim, Jong Myoung; Moon, Jong Hwa; Chung, Yong Sam; Lee, Jin Hong

2010-01-01

Airborne particulate matters, especially the PM2.5 (aerodynamic equivalent diameter, AED, less than 2.5 )m) fraction has been important. This is because of their potential for deposition on to the human respiratory system being accompanied by many harmful trace metals (such as As, Cd, Cr, Cu, Mn, Pb, Se, and Zn). As most people spend more than 80% of their time indoors, indoor air quality (IAQ) can exert a considerable impact on the inhalation condition of toxic substances. Therefore, assessment of the absolute concentration levels and elemental composition of PM in an indoor environment such as subway station can be used as a practical barometer of IAQ. The contaminants originated from the indoor pollution sources as well as various outdoor sources are easily accumulated in indoor environment dissimilar to the outdoor. Especially, since the natural ventilation is nearly impossible in the subway station, its pollution status can be worsened under the circumstance that contaminants are constantly originated and circulated inside of station by the repetitive action of subway trains. In this study, a total of 60 PM2.5 samples were collected for 4 seasonal campaigns in 2009 with a low-volume air sampler at one subway station in Daejeon, Korea. We undertook the measurements of up to 25 elements in PM2.5 using an instrumental neutron activation analysis (INAA) and X-ray fluorescence (XRF). And inorganic ion species (SO 4 2- , NO 3 - , NH 4 + ) also were determined by ion chromatography (IC). Next, sources at indoor/outdoor environment were identified and the contributions of each source were quantified by positive matrix factorization (PMF).

ANALYSIS OF THE RESULTS OF MEASUREMENT OF CONCENTRATIONS OF AIR POLLUTION WITH PM10 AND PM2.5 MEASURING STATION SQUARE OF POZNAN IN BYDGOSZCZ

Directory of Open Access Journals (Sweden)

Rafał Pasela

2017-02-01

Full Text Available The phenomenon of suspended particulate pollution PM10 and PM2.5 occurs in large urban areas where the main source of their presence is communication, which is primarily related to the combustion of liquid fuels. PM2.5 dust pollution is a major risk factor for diseases of the respiratory, cardiovascular, and allergy. Act regulating the standards and target dates for reducing concentrations of particulate matter in urban areas and in all the cities of over 100 thousand. residents of the Directive of the European Parliament and Council Directive 2008/50/EC of 21 May 2008. on ambient air quality and cleaner air for Europe (CAFE. The acceptable level of average daily concentration of PM10 is 50 μg/m3 and may be exceeded by not more than 35 times a year, while the level of allowable annual average concentration of 40 μg/m3. The aim of this study was to assess the state of air pollution of dust PM10 and PM2.5 for the selected area of the city of Bydgoszcz. The analysis was conducted using data from air monitoring stations located at Poznanska street. The station is owned by the Provincial Inspectorate for Environmental Protection (VIEP in Bydgoszcz. The studies have shown that the annual average concentration of particulate matter analyzed station in Bydgoszcz in the years 2013-2015 amounted to PM10 41 μg/m3 PM2.5 and 23 μg/m3. The results are on the borderline of acceptable levels of concentration resulting from the Regulation of the Minister of the Environment of 2 August 2012. The concentrations of particulate matter in ambient air are strongly associated with meteorological conditions. The definitely higher concentrations observed in the autumn-winter season. The decrease in temperature causes the combustion in the boiler house of fuels with a high emissions. The highest average daily concentration of suspended particulate matter was observed on Thursday and Friday in the winter months, and while the lowest concentration was recorded in the

Spatial distribution of particulate matter (PM10 and PM2.5) in Seoul Metropolitan Subway stations.

Science.gov (United States)

Kim, Ki Youn; Kim, Yoon Shin; Roh, Young Man; Lee, Cheol Min; Kim, Chi Nyon

2008-06-15

The aims of this study are to examine the concentrations of PM10 and PM2.5 in areas within the Seoul Metropolitan Subway network and to provide fundamental data in order to protect respiratory health of subway workers and passengers from air pollutants. A total of 22 subway stations located on lines 1-4 were selected based on subway official's guidance. At these stations both subway worker areas (station offices, rest areas, ticket offices and driver compartments) and passengers areas (station precincts, subway carriages and platforms) were the sites used for measuring the levels of PM. The mean concentrations of PM10 and PM2.5 were relatively higher on platforms, inside subway carriages and in driver compartments than in the other areas monitored. The levels of PM10 and PM2.5 for station precincts and platforms exceeded the 24-h acceptable threshold limits of 150 microg/m3 for PM10 and 35 microg/m3 for PM2.5, which are regulated by the U.S. Environmental Protection Agency (EPA). However, levels measured in station and ticket offices fell below the respective threshold. The mean PM10 and PM2.5 concentrations on platforms located underground were significantly higher than those at ground level (p<0.05).

Seasonal variations in the concentration and solubility of elements in atmospheric particulate matter: a case study in Northern Italy

Directory of Open Access Journals (Sweden)

Canepari S.

2013-04-01

Full Text Available Atmospheric particulate matter is characterized by a variety of chemical components, generally produced by different sources. Chemical fractionation of elements, namely the determination of their extractable and residual fractions, may reliably increase the selectivity of some elements as tracers of specific PM sources. Seasonal variations of atmospheric particulate matter concentration in PM10 and PM2.5, of elemental concentration in PM10 and PM2.5, of the extractable and residual fraction of elements in different size fractions in the range 0.18 – 18 μm are reported in this paper. The effect of the ageing of the air masses is discussed.

Isotopic signatures suggest important contributions from recycled gasoline, road dust and non-exhaust traffic sources for copper, zinc and lead in PM10 in London, United Kingdom

Science.gov (United States)

Dong, Shuofei; Ochoa Gonzalez, Raquel; Harrison, Roy M.; Green, David; North, Robin; Fowler, Geoff; Weiss, Dominik

2017-09-01

The aim of this study was to improve our understanding of what controls the isotope composition of Cu, Zn and Pb in particulate matter (PM) in the urban environment and to develop these isotope systems as possible source tracers. To this end, isotope ratios (Cu, Zn and Pb) and trace element concentrations (Fe, Al, Cu, Zn, Sb, Ba, Pb, Cr, Ni and V) were determined in PM10 collected at two road sites with contrasting traffic densities in central London, UK, during two weeks in summer 2010, and in potential sources, including non-combustion traffic emissions (tires and brakes), road furniture (road paint, manhole cover and road tarmac surface) and road dust. Iron, Ba and Sb were used as proxies for emissions derived from brake pads, and Ni, and V for emissions derived from fossil fuel oil. The isotopic composition of Pb (expressed using 206Pb/207Pb) ranged between 1.1137 and 1.1364. The isotope ratios of Cu and Zn expressed as δ65CuNIST976 and δ66ZnLyon ranged between -0.01‰ and +0.51‰ and between -0.21‰ and +0.33‰, respectively. We did not find significant differences in the isotope signatures in PM10 over the two weeks sampling period and between the two sites, suggesting similar sources for each metal at both sites despite their different traffic densities. The stable isotope composition of Pb suggests significant contribution from road dust resuspension and from recycled leaded gasoline. The Cu and Zn isotope signatures of tires, brakes and road dust overlap with those of PM10. The correlation between the enrichments of Sb, Cu, Ba and Fe in PM10 support the previously established hypothesis that Cu isotope ratios are controlled by non-exhaust traffic emission sources in urban environments (Ochoa Gonzalez et al., 2016). Analysis of the Zn isotope signatures in PM10 and possible sources at the two sites suggests significant contribution from tire wear. However, temporary additional sources, likely high temperature industrial emissions, need to be invoked

Extractable organic matter in PM10 from LiWan district of Guangzhou City, PR China.

Science.gov (United States)

Bi, Xinhui; Sheng, Guoying; Peng, Peng an; Zhang, Zhiqiang; Fu, Jiamo

2002-12-02

PM10 (particulate matter with aerodynamic diameter gas chromatography/mass spectrometry analysis. The sigma(n)-alkane and sigmaPAHs ranged from 26.4 to 719.2 ng/m3 and 7.4 to 159.4 ng/m3, respectively. A seasonal fluctuation was clearly evident with higher concentrations occurring during the colder months (April). In addition, some compositional differences are observed for the organic compounds in samples collected from different heights above ground level. Higher sites had a significant contribution from vascular plant wax. The presence of petroleum products with no carbon number preference, pristane, phytane and a significant unresolved complex mixture (UCM) with unresolved to resolved components ratio (U/R) of 6.2-13.2 confirm the petroleum component. The relative distribution of n-alkanes and the values of molecular diagnostic ratio, such as carbon preference index (CPI) values ranging from 1.0 to 1.4 (for the whole range of n-alkanes), indicated the importance of petroleum and diesel residues and gasoline emissions, as well as the minor contribution of n-alkanes emitted directly from epicuticular waxes. Indeed, the percent contribution of leaf 'wax' n-alkanes (5.2-19.4%) indicated a low contribution of biogenic sources. The fossil fuel biomarkers, hopanes and steranes were observed in the PM10 samples, which indicate a petroleum origin. The distribution pattern of PAHs was characteristic of anthropogenic emissions. Coupling carbon number maximum (Cmax), CPI, U/R values, molecular marker and molecular diagnostic ratios for alkanes and PAHs revealed a classification of natural biogenic and anthropogenic components of atmospheric aerosols. These analyses support the conclusion that vehicular emission was the major source of organic compounds during the study period, while the contribution of epicuticular waxes emitted by terrestrial plants was minor.

A candidate framework for PM2.5 source identification in highly industrialized urban-coastal areas

Science.gov (United States)

Mateus, Vinícius Lionel; Gioda, Adriana

2017-09-01

The variability of PM sources and composition impose tremendous challenges for police makers in order to establish guidelines. In urban PM, sources associated with industrial processes are among the most important ones. In this study, a 5-year monitoring of PM2.5 samples was carried out in an industrial district. Their chemical composition was strategically determined in two campaigns in order to check the effectiveness of mitigation policies. Gaseous pollutants (NO2, SO2, and O3) were also monitored along with meteorological variables. The new method called Conditional Bivariate Probability Function (CBPF) was successfully applied to allocate the observed concentration of criteria pollutants (gaseous pollutants and PM2.5) in cells defined by wind direction-speed which provided insights about ground-level and elevated pollution plumes. CBPF findings were confirmed by the Theil-Sen long trend estimations for criteria pollutants. By means of CBPF, elevated pollution plumes were detected in the range of 0.54-5.8 μg m-3 coming from a direction associated to stacks. With high interpretability, the use of Conditional Inference Trees (CIT) provided both classification and regression of the speciated PM2.5 in the two campaigns. The combination of CIT and Random Forests (RF) point out NO3- and Ca+2 as important predictors for PM2.5. The latter predictor mostly associated to non-sea-salt sources, given a nss-Ca2+ contribution equal to 96%.

Source contributions to PM10 and arsenic concentrations in Central Chile using positive matrix factorization

Science.gov (United States)

Hedberg, Emma; Gidhagen, Lars; Johansson, Christer

Sampling of particles (PM10) was conducted during a one-year period at two rural sites in Central Chile, Quillota and Linares. The samples were analyzed for elemental composition. The data sets have undergone source-receptor analyses in order to estimate the sources and their abundance's in the PM10 size fraction, by using the factor analytical method positive matrix factorization (PMF). The analysis showed that PM10 was dominated by soil resuspension at both sites during the summer months, while during winter traffic dominated the particle mass at Quillota and local wood burning dominated the particle mass at Linares. Two copper smelters impacted the Quillota station, and contributed to 10% and 16% of PM10 as an average during summer and winter, respectively. One smelter impacted Linares by 8% and 19% of PM10 in the summer and winter, respectively. For arsenic the two smelters accounted for 87% of the monitored arsenic levels at Quillota and at Linares one smelter contributed with 72% of the measured mass. In comparison with PMF, the use of a dispersion model tended to overestimate the smelter contribution to arsenic levels at both sites. The robustness of the PMF model was tested by using randomly reduced data sets, where 85%, 70%, 50% and 33% of the samples were included. In this way the ability of the model to reconstruct the sources initially found by the original data set could be tested. On average for all sources the relative standard deviation increased from 7% to 25% for the variables identifying the sources, when decreasing the data set from 85% to 33% of the samples, indicating that the solution initially found was very stable to begin with. But it was also noted that sources due to industrial or combustion processes were more sensitive for the size of the data set, compared to the natural sources as local soil and sea spray sources.

Sources of the PM10 aerosol in Flanders, Belgium, and re-assessment of the contribution from wood burning.

Science.gov (United States)

Maenhaut, Willy; Vermeylen, Reinhilde; Claeys, Magda; Vercauteren, Jordy; Roekens, Edward

2016-08-15

From 30 June 2011 to 2 July 2012 PM10 aerosol samples were simultaneously taken every 4th day at four urban background sites in Flanders, Belgium. The sites were in Antwerpen, Gent, Brugge, and Oostende. The PM10 mass concentration was determined by weighing; organic and elemental carbon (OC and EC) were measured by thermal-optical analysis, the wood burning tracers levoglucosan, mannosan and galactosan were determined by gas chromatography/mass spectrometry, 8 water-soluble ions were measured by ion chromatography, and 15 elements were determined by a combination of inductively coupled plasma atomic emission spectrometry and mass spectrometry. The multi-species dataset was subjected to receptor modeling by PMF. The 10 retained factors (with their overall average percentage contributions to the experimental PM10 mass) were wood burning (9.5%), secondary nitrate (24%), secondary sulfate (12.6%), sea salt (10.0%), aged sea salt (19.2%), crustal matter (9.7%), non-ferrous metals (1.81%), traffic (10.3%), non-exhaust traffic (0.52%), and heavy oil burning (3.0%). The average contributions of wood smoke for the four sites were quite substantial in winter and ranged from 12.5 to 20% for the PM10 mass and from 47 to 64% for PM10 OC. Wood burning appeared to be also a notable source of As, Cd, and Pb. The contribution from wood burning to the PM10 mass and OC was also assessed by making use of levoglucosan as single marker compound and the conversion factors of Schmidl et al. (2008), as done in our previous study on wood burning in Flanders (Maenhaut et al., 2012). However, the apportionments were much lower than those deduced from PMF. It seems that the conversion factors of Schmidl et al. (2008) may not be applicable to wood burning in Flanders. From scatter plots of the PMF-derived wood smoke OC and PM versus levoglucosan, we arrived at conversion factors of 9.7 and 22.6, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Black Carbon and Particulate Matter (PM2.5) Concentrations in New York City’s Subway Stations

Science.gov (United States)

2015-01-01

The New York City (NYC) subway is the main mode of transport for over 5 million passengers on an average weekday. Therefore, airborne pollutants in the subway stations could have a significant impact on commuters and subway workers. This study looked at black carbon (BC) and particulate matter (PM2.5) concentrations in selected subway stations in Manhattan. BC and PM2.5 levels were measured in real time using a Micro-Aethalometer and a PDR-1500 DataRAM, respectively. Simultaneous samples were also collected on quartz filters for organic and elemental carbon (OC/EC) analysis and on Teflon filters for gravimetric and trace element analysis. In the underground subway stations, mean real time BC concentrations ranged from 5 to 23 μg/m3, with 1 min average peaks >100 μg/m3, while real time PM2.5 levels ranged from 35 to 200 μg/m3. Mean EC levels ranged from 9 to 12.5 μg/m3. At street level on the same days, the mean BC and PM2.5 concentrations were below 3 and 10 μg/m3, respectively. This study shows that both BC soot and PM levels in NYC’s subways are considerably higher than ambient urban street levels and that further monitoring and investigation of BC and PM subway exposures are warranted. PMID:25409007

Source apportionment of PM10 and PM2.5 in major urban Greek agglomerations using a hybrid source-receptor modeling process.

Science.gov (United States)

Argyropoulos, G; Samara, C; Diapouli, E; Eleftheriadis, K; Papaoikonomou, K; Kungolos, A

2017-12-01

A hybrid source-receptor modeling process was assembled, to apportion and infer source locations of PM 10 and PM 2.5 in three heavily-impacted urban areas of Greece, during the warm period of 2011, and the cold period of 2012. The assembled process involved application of an advanced computational procedure, the so-called Robotic Chemical Mass Balance (RCMB) model. Source locations were inferred using two well-established probability functions: (a) the Conditional Probability Function (CPF), to correlate the output of RCMB with local wind directional data, and (b) the Potential Source Contribution Function (PSCF), to correlate the output of RCMB with 72h air-mass back-trajectories, arriving at the receptor sites, during sampling. Regarding CPF, a higher-level conditional probability function was defined as well, from the common locus of CPF sectors derived for neighboring receptor sites. With respect to PSCF, a non-parametric bootstrapping method was applied to discriminate the statistically significant values. RCMB modeling showed that resuspended dust is actually one of the main barriers for attaining the European Union (EU) limit values in Mediterranean urban agglomerations, where the drier climate favors build-up. The shift in the energy mix of Greece (caused by the economic recession) was also evidenced, since biomass burning was found to contribute more significantly to the sampling sites belonging to the coldest climatic zone, particularly during the cold period. The CPF analysis showed that short-range transport of anthropogenic emissions from urban traffic to urban background sites was very likely to have occurred, within all the examined urban agglomerations. The PSCF analysis confirmed that long-range transport of primary and/or secondary aerosols may indeed be possible, even from distances over 1000km away from study areas. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of Ground-Based PM2.5 and PM10 Concentrations in China, India, and the U.S.

Directory of Open Access Journals (Sweden)

Xingchuan Yang

2018-07-01

Full Text Available Urbanization and industrialization have spurred air pollution, making it a global problem. An understanding of the spatiotemporal characteristics of PM2.5 and PM10 concentrations (particulate matter with an aerodynamic diameter of less than 2.5 μm and 10 μm, respectively is necessary to mitigate air pollution. We compared the characteristics of PM2.5 and PM10 concentrations and their trends of China, India, and the U.S. from 2014 to 2017. Particulate matter levels were lowest in the U.S., while China showed higher concentrations, and India showed the highest. Interestingly, significant declines in PM2.5 and PM10 concentrations were found in some of the most polluted regions in China as well as the U.S. No comparable decline was observed in India. A strong seasonal trend was observed in China and India, with the highest values occurring in winter and the lowest in summer. The opposite trend was noted for the U.S. PM2.5 was highly correlated with PM10 for both China and India, but the correlation was poor for the U.S. With regard to reducing particulate matter pollutant concentrations, developing countries can learn from the experiences of developed nations and benefit by establishing and implementing joint regional air pollution control programs.

Air quality in terms of particulate matter (PM10) and element components in Antananarivo city

International Nuclear Information System (INIS)

Raoelina Andriambololona; Rakotondramanana, H.T.; Rasoazanany, E.O.; Randriamanivo, L.V.; Rasolofonirina, M.; Razafy Andrianarivo, R.

2001-01-01

The main objective of this research was to study the size distribution of toxic elements, undesirables ones and PM10 in the aerosols of Antananarivo urban areas using Total reflection X-ray Fluorescence. This work was carried out in the framework of Co-ordinated Research Program organised by the IAEA in 1998. The air sampler DICHOTOMOUS was used for sampling, with which two types of aerosols could be obtained: respirable aerosols or fine particles (aerodynamic diameter below 2.5 μm PM-2 ,5 ) and inhalable or coarse particles (aerodynamic diameter from 2.5 μm to 10μm PM 10 ). Samples were taken from six sampling sites, namely Ambohidahy tunnel, Ambanidia tunnel, Andravoahangy, Soarano, Mahamasina and Ankorondrano. Then, they were digested with acid digestion bomb. The results showed the presence of elements such as sulfur (S), chlorine (Cl), kalium (K), calcium (Ca), titanium (Ti), lead (Pb) in the aerosols. Their concentrations are higher in respirable particles. For classical air pollutant components, particularly lead and PM10, the 1.8 μg.m -3 mean concentration value of lead is largely higher than 0.5μg. m -3 , which is the WHO (World Health organization) adopted value, and above the USEPA (United States Environmental Protection Agency) maximum admissible one (1.5 μg.m -3 ) as well. Regarding the size distribution of lead, the results showed that the small particles were mainly enriched in lead. The same observation can also be stated for PM10 with a 240 μg.m -3 mean concentration value , higher than 150 μg.m - 3 , adopted by the two above-mentioned organizations. Therefore, the Antananarivo urban area is classified as saturated zone for both parameters (lead and particulate matter). In addition, the results of Mason enrichment factors showed that the elements such as sulfur (S), chromium (Cr), copper (Cu), zinc (Zn), bromine (Br), and lead (Pb) are from both natural and anthropogenic sources. The elements such as kalium (K), chlorine (Cl), calcium (Ca

Origin of inorganic and organic components of PM2.5 in subway stations of Barcelona, Spain.

Science.gov (United States)

Martins, Vânia; Moreno, Teresa; Minguillón, María Cruz; van Drooge, Barend L; Reche, Cristina; Amato, Fulvio; de Miguel, Eladio; Capdevila, Marta; Centelles, Sonia; Querol, Xavier

2016-01-01

The present work assesses indoor air quality in stations of the Barcelona subway system. PM2.5 concentrations on the platforms of 4 subway stations were measured during two different seasons and the chemical composition was determined. A Positive Matrix Factorization analysis was performed to identify and quantify the contributions of major PM2.5 sources in the subway stations. Mean PM2.5 concentrations varied according to the stations design and seasonal periods. PM2.5 was composed of haematite, carbonaceous aerosol, crustal matter, secondary inorganic compounds, trace elements, insoluble sulphate and halite. Organic compounds such as PAHs, nicotine, levoglucosan and aromatic musk compounds were also identified. Subway PM2.5 source comprised emissions from rails, wheels, catenaries, brake pads and pantographs. The subway source showed different chemical profiles for each station, but was always dominated by Fe. Control actions on the source are important for the achievement of better air quality in the subway environment. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Characterisation and quantification of the sources of PM{sub 10} during air pollution episodes in the UK

Energy Technology Data Exchange (ETDEWEB)

Muir, David [Environmental Quality Unit, Department of Planning, Transport and Sustainable Development, Bristol City Council, The CREATE Centre, Smeaton Road, Bristol BS1 6XN (United Kingdom); Longhurst, J.W.S.; Tubb, A. [Faculty of Applied Sciences, University of the West of England, Frenchay Campus, Coldharbour Lane, Bristol BS16 1QY (United Kingdom)

2006-04-01

Data for concentrations of PM{sub 10} and gaseous pollutants from sites in the UK Automatic Urban and Rural Network have been examined during periods of elevated concentrations of PM{sub 10}. The ratios of concentrations of PM{sub 10} to those of the other pollutants were used to determine the most probable source of the additional particles. The hypothesis is that because the concentrations of PM{sub 10} were divided by those of the other pollutants, the ratio should decrease when PM{sub 10} and the other pollutants have a common source. Conversely, the ratio should increase when the sources are different. During episodes where road traffic was the most probable source of the additional particles, the ratios of concentrations of PM{sub 10} to carbon monoxide and oxides of nitrogen did decrease, but the comparable ratios for sulphur dioxide and ozone increased. In contrast, during episodes known to have been caused by construction activity, all these ratios increased. This is taken to show that the basic hypothesis is valid. For prolonged episodes, it was possible to use data averaged over the total duration of the episode for the purposes of source identification. For sporadic construction, or other short-duration episodes, it was necessary to use time series data. The data have also been used to calculate the differences between hourly average concentrations of pollutants measured during episodes and long-term hourly average concentrations. These have been used to model the additional PM{sub 10} during air pollution episodes associated with construction activities and road traffic emissions. This confirms the lack of relationship between PM{sub 10} and other pollutants during construction works. During episodes arising from road traffic emissions, there was good agreement between measured and modelled additional concentrations of PM{sub 10} when an appropriate factor, F, related to the contribution of road traffic emissions to PM{sub 10} at different site types

Spatiotemporal estimation of historical PM2.5 concentrations using PM10, meteorological variables, and spatial effect

Science.gov (United States)

Li, Lianfa; Wu, Anna H.; Cheng, Iona; Chen, Jiu-Chiuan; Wu, Jun

2017-10-01

Monitoring of fine particulate matter with diameter health outcomes such as cancer. In this study, we aimed to design a flexible approach to reliably estimate historical PM2.5 concentrations by incorporating spatial effect and the measurements of existing co-pollutants such as particulate matter with diameter additive non-linear model. The spatiotemporal model was evaluated, using leaving-one-site-month-out cross validation. Our final daily model had an R2 of 0.81, with PM10, meteorological variables, and spatial autocorrelation, explaining 55%, 10%, and 10% of the variance in PM2.5 concentrations, respectively. The model had a cross-validation R2 of 0.83 for monthly PM2.5 concentrations (N = 8170) and 0.79 for daily PM2.5 concentrations (N = 51,421) with few extreme values in prediction. Further, the incorporation of spatial effects reduced bias in predictions. Our approach achieved a cross validation R2 of 0.61 for the daily model when PM10 was replaced by total suspended particulate. Our model can robustly estimate historical PM2.5 concentrations in California when PM2.5 measurements were not available.

Experimental Investigation of the Effects of Some Operating Diesel Engine Variables on Emitted Particulate Matters (PM

Directory of Open Access Journals (Sweden)

Adel M. Saleh

2012-03-01

Full Text Available The diesel engine is the most efficient prime mover commonly available today. Diesel engines move a large portion of the world’s goods, power much of the world’s equipment, and generate electricity more economically than any other device in their size range. But the diesel is one of the largest contributors to environmental pollution problems worldwide, and will remain so, with large increases expected in vehicle population. This experimental study has been conducted with direct injection diesel engine and particulate matters (PM concentrations were measured at variable operating variables. The results show that PM concentrations influence by changing equivalence ratio, load, engine speed and injection timing

Vertical and horizontal variability of PM10 source contributions in Barcelona during SAPUSS

Science.gov (United States)

Brines, Mariola; Dall'Osto, Manuel; Amato, Fulvio; Cruz Minguillón, María; Karanasiou, Angeliki; Alastuey, Andrés; Querol, Xavier

2016-06-01

During the SAPUSS campaign (Solving Aerosol Problems by Using Synergistic Strategies) PM10 samples at 12-hour resolution were simultaneously collected at four monitoring sites located in the urban agglomerate of Barcelona (Spain). A total of 221 samples were collected from 20 September to 20 October 2010. The Road Site (RS) site and the Urban Background (UB) site were located at street level, whereas the Torre Mapfre (TM) and the Torre Collserola (TC) sites were located at 150 m a.s.l. by the sea side within the urban area and at 415 m a.s.l. 8 km inland, respectively. For the first time, we are able to report simultaneous PM10 aerosol measurements, allowing us to study aerosol gradients at both horizontal and vertical levels. The complete chemical composition of PM10 was determined on the 221 samples, and factor analysis (positive matrix factorisation, PMF) was applied. This resulted in eight factors which were attributed to eight main aerosol sources affecting PM10 concentrations in the studied urban environment: (1) vehicle exhaust and wear (2-9 µg m-3, 10-27 % of PM10 mass on average), (2) road dust (2-4 µg m-3, 8-12 %), (3) mineral dust (5 µg m-3, 13-26 %), (4) aged marine (3-5 µg m-3, 13-20 %), (5) heavy oil (0.4-0.6 µg m-3, 2 %), (6) industrial (1 µg m-3, 3-5 %), (7) sulfate (3-4 µg m-3, 11-17 %) and (8) nitrate (4-6 µg m-3, 17-21 %). Three aerosol sources were found to be enhanced at the ground levels (confined within the urban ground levels of the city) relative to the upper levels: (1) vehicle exhaust and wear (2.8 higher), (2) road dust (1.8 higher) and (3) local urban industries/crafts workshops (1.6 higher). Surprisingly, the other aerosol sources were relatively homogeneous at both horizontal and vertical levels. However, air mass origin and meteorological parameters also played a key role in influencing the variability of the factor concentrations. The mineral dust and aged marine factors were found to be a mixture of natural and

Indoor and Outdoor Levels and Sources of Submicron Particles (PM1) at Homes in Edmonton, Canada.

Science.gov (United States)

Bari, Md Aynul; Kindzierski, Warren B; Wallace, Lance A; Wheeler, Amanda J; MacNeill, Morgan; Héroux, Marie-Ève

2015-06-02

Exposure to submicron particles (PM1) is of interest due to their possible chronic and acute health effects. Seven consecutive 24-h PM1 samples were collected during winter and summer 2010 in a total of 74 nonsmoking homes in Edmonton, Canada. Median winter concentrations of PM1 were 2.2 μg/m(3) (interquartile range, IQR = 0.8-6.1 μg/m(3)) and 3.3 μg/m(3) (IQR = 1.5-6.9 μg/m(3)) for indoors and outdoors, respectively. In the summer, indoor (median 4.4 μg/m(3), IQR = 2.4-8.6 μg/m(3)) and outdoor (median 4.3 μg/m(3), IQR = 2.6-7.4 μg/m(3)) levels were similar. Positive matrix factorization (PMF) was applied to identify and apportion indoor and outdoor sources of elements in PM1 mass. Nine sources contributing to both indoor and outdoor PM1 concentrations were identified including secondary sulfate, soil, biomass smoke and environmental tobacco smoke (ETS), traffic, settled and mixed dust, coal combustion, road salt/road dust, and urban mixture. Three additional indoor sources were identified i.e., carpet dust, copper-rich, and silver-rich. Secondary sulfate, soil, biomass smoke and ETS contributed more than 70% (indoors: 0.29 μg/m(3), outdoors: 0.39 μg/m(3)) of measured elemental mass in PM1. These findings can aid understanding of relationships between submicron particles and health outcomes for indoor/outdoor sources.

The Characteristics and Potential Source Area Analysis of PM2.5 Concentration for Zhengzhou during 2016

Science.gov (United States)

Li, D.; Liu, J.; Li, S.; Wang, C.; Zhou, S.

2018-04-01

This study used the HYSPLIT-4 model combined with cluster analysis, potential source pollution contribution functions and other methods to analyse the ground air pollution monitoring data and meteorological data in Zhengzhou during 2016. The results showed that: 1) the level of PM2.5 reached the low value in summer. The PM2.5 concentration reached the highest level in December and reached the lowest level in August. The daily variation characteristics of PM2.5 concentration in different seasons were roughly the same, and it had an obviously "double-peak" structure. 2) The annual PM2.5 concentration was positively correlated with atmospheric pressure and relative humidity. The annual PM2.5 concentration was negatively correlated with temperature, visibility, precipitation, and wind speed. 3) In winter, the air mass trajectory that through the northern Sichuan - Gansu - Shaanxi - Hubei was polluted seriously, and the level of PM2.5 was the highest which reached to 202.13 μg/m3. In summer, the air mass trajectory that came from Hubei was the lowest level with the value is 40.17 μg/m3. 4) The potential source areas located in northwest of Zhengzhou, Gansu, Hubei and Beijing-Tianjin-Hebei region in spring. The surrounding of Zhengzhou contributed to the pollution of Zhengzhou. The potential source areas appeared in Shaanxi, Sichuan, and Qinghai, the border between Ningxia and Inner Mongolia in autumn. In winter the potential source areas located in Jiangsu, Hubei, Henan, eastern of Shanxi, southern of Shanxi, Ningxia and the area of Yellow Sea, etc.

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

Science.gov (United States)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press

Global Particulate Matter Source Apportionment

Science.gov (United States)

Lamancusa, C.; Wagstrom, K.

2017-12-01

As our global society develops and grows it is necessary to better understand the impacts and nuances of atmospheric chemistry, in particular those associated with atmospheric particulate matter. We have developed a source apportionment scheme for the GEOS-Chem global atmospheric chemical transport model. While these approaches have existed for several years in regional chemical transport models, the Global Particulate Matter Source Apportionment Technology (GPSAT) represents the first incorporation into a global chemical transport model. GPSAT runs in parallel to a standard GEOS-Chem run. GPSAT uses the fact that all molecules of a given species have the same probability of undergoing any given process as a core principle. This allows GPSAT to track many different species using only the flux information provided by GEOS-Chem's many processes. GPSAT accounts for the change in source specific concentrations as a result of aqueous and gas-phase chemistry, horizontal and vertical transport, condensation and evaporation on particulate matter, emissions, and wet and dry deposition. By using fluxes, GPSAT minimizes computational cost by circumventing the computationally costly chemistry and transport solvers. GPSAT will allow researchers to address many pertinent research questions about global particulate matter including the global impact of emissions from different source regions and the climate impacts from different source types and regions. For this first application of GPSAT, we investigate the contribution of the twenty largest urban areas worldwide to global particulate matter concentrations. The species investigated include: ammonium, nitrates, sulfates, and the secondary organic aerosols formed by the oxidation of benzene, isoprene, and terpenes. While GPSAT is not yet publically available, we will incorporate it into a future standard release of GEOS-Chem so that all GEOS-Chem users will have access to this new tool.

Personal exposure to PM2.5 and biomarkers of DNA damage

DEFF Research Database (Denmark)

Sørensen, Mette; Autrup, Herman; Hertel, Ole

2003-01-01

Ambient particulate air pollution assessed as outdoor concentrations of particulate matter PM(2.5)) has been associated with an increased cancer risk. However, outdoor PM(2.5) concentrations may not be the best measure of the individual particle exposure that is a sum...... of many sources besides outdoor particle levels, e.g., environmental tobacco smoke and cooking. We measured personal PM(2.5) and black smoke exposure in 50 students four times over 1 year and analyzed for biomarkers of different types of DNA damages. Ambient PM(2.5) concentrations were also measured...... collections were analyzed for 8-oxodG and 1-hydroxypyrene. Personal PM(2.5) exposure was found to be a predictor of 8-oxodG in lymphocyte DNA with an 11% increase in 8-oxodG/10 microg/m(3) increase in personal PM(2.5) exposure (P = 0.007). No other associations between exposure markers and biomarkers could...

The modifying effect of the building envelope on population exposure to PM2.5 from outdoor sources

Science.gov (United States)

Taylor, J; Shrubsole, C; Davies, M; Biddulph, P; Das, P; Hamilton, I; Vardoulakis, S; Mavrogianni, A; Jones, B; Oikonomou, E

2014-01-01

A number of studies have estimated population exposure to PM2.5 by examining modeled or measured outdoor PM2.5 levels. However, few have taken into account the mediating effects of building characteristics on the ingress of PM2.5 from outdoor sources and its impact on population exposure in the indoor domestic environment. This study describes how building simulation can be used to determine the indoor concentration of outdoor-sourced pollution for different housing typologies and how the results can be mapped using building stock models and Geographical Information Systems software to demonstrate the modifying effect of dwellings on occupant exposure to PM2.5 across London. Building archetypes broadly representative of those in the Greater London Authority were simulated for pollution infiltration using EnergyPlus. In addition, the influence of occupant behavior on indoor levels of PM2.5 from outdoor sources was examined using a temperature-dependent window-opening scenario. Results demonstrate a range of I/O ratios of PM2.5, with detached and semi-detached dwellings most vulnerable to high levels of infiltration. When the results are mapped, central London shows lower I/O ratios of PM2.5 compared with outer London, an apparent inversion of exposure most likely caused by the prevalence of flats rather than detached or semi-detached properties. PMID:24713025

The impact of long-range-transport on PM1 and PM2.5 at a Central Mediterranean site

Science.gov (United States)

Perrone, M. R.; Becagli, S.; Garcia Orza, J. A.; Vecchi, R.; Dinoi, A.; Udisti, R.; Cabello, M.

2013-06-01

Water soluble ions, methanesulfonate, organic and elemental carbon, and metals in PM2.5 and PM1 samples were analysed by Positive Matrix Factorization to identify and quantify major sources of fine particles at a Central Mediterranean site. The cluster analysis of four-day back trajectories was used to determine the dependence of PM2.5 and PM1 levels and composition on air-flows. The cluster analysis has identified six, six, and seven distinct air-flow types arriving at 500, 1500, and 3000 m above sea level (asl), respectively. Slow-west (Wslow) and north-eastern (NE) flows at 500 and 1500 m asl were the most frequent and were associated with the highest PM2.5 and PM1 concentrations. The PM concentrations from combustion sources including biomass burning were at their maximum under north-western (NW) flows. Similarly, the ammonium sulphate source was enhanced under Wslow and NE flows. South-eastern Mediterranean Sea air-flows were associated with the highest PM2.5 concentrations due to the heavy-oil-combustion source and the highest PM2.5 and PM1 concentrations due to the secondary marine source. PM2.5 concentrations due to the reacted dust and traffic source and PM1 concentrations due to the nitrate with reacted dust and mixed anthropogenic source showed no clear dependence on air-flows. This work highlights the different impact of aerosol sources on PM2.5 and PM1 fractions, being PM1 more adequate to control anthropogenic emissions from combustion sources.

Biomagnetic monitoring of particulate matter (PM through leaves of an invasive alien plant Lantana camara in an Indo-Burma hot spot region

Directory of Open Access Journals (Sweden)

Prabhat Kumar Rai

2016-03-01

Full Text Available Present study was performed in urban forests of Aizawl, Mizoram, North East India falling under an Indo-Burma hot spot region of existing ecological relevance and pristine environment. Phyto-sociolology of invasive weeds has been performed and results revealed that Lantana camara was the most dominant invasive weed. Further, the air quality studies revealed high suspended particulate matter (SPM as well as respirable suspended particulate matter (RSPM in ambient air of Aizawl, Mizoram, North East India. Bio-magnetic monitoring through plant leaves has been recognised as recent thrust area in the field of particulate matter (PM science. We aimed to investigate that whether magnetic properties of Lantana camara leaves may act as proxy of PM pollution and hence an attempt towards it's sustainable management. Magnetic susceptibility (χ, Anhyste reticremanent magnetization (ARM and Saturation isothermal remanent magnetization (SIRM of Lantana camara plant leaves were assessed and concomitantly correlated these magnetic properties with ambient PM in order to screen this invasive plant which may act as proxy for ambient PM concentrations. Results revealed high χ, ARM, SIRM of Lantana camara leaves and moreover, these parameters were having significant and positive correlation with ambient SPM as well as RSPM. Therefore, present study recommended the use of Lantana camara as bio-magnetic monitor which may further have sustainable management implications of an invasive plant.

Personal and ambient PM2.5 exposure assessment in the city of Agra

Directory of Open Access Journals (Sweden)

M. Habil

2016-03-01

Full Text Available Human exposure to fine particles can have significant harmful effects on the respiratory and cardiovascular system. To investigate daily exposure characteristics to PM2.5 with ambient concentrations in an urban environment, a personal exposure measurements were conducted for school children, office workers and at their residents, in the city of Taj ‘Agra’, India. In order to account for all the sources of particulate matter exposure, measurements on several different days during December 2013 to February 2014 were carried out. Personal environment monitors (PEM and APM 550 were used to measure PM2.5 concentration. The research findings provide insight into possible sources and their interaction with human activities in modifying the human exposure levels. Keywords: Personal exposure, PM2.5, Ambient concentration, Correlation analysis, Health effects

PMF and PSCF based source apportionment of PM2.5 at a regional background site in North China

Science.gov (United States)

Zong, Zheng; Wang, Xiaoping; Tian, Chongguo; Chen, Yingjun; Fu, Shanfei; Qu, Lin; Ji, Ling; Li, Jun; Zhang, Gan

2018-05-01

To apportion regional PM2.5 (atmospheric particles with aerodynamic diameter water-soluble ions and inorganic elements, various approaches, such as Mann-Kendall test, chemical mass closure, ISORROPIA II model, Positive Matrix Factorization (PMF) linked with Potential Source Contribution Function (PSCF), were used to explore the PM2.5 speciation, sources, and source regions. Consequently, distinct seasonal variations of PM2.5 and its main species were found and could be explained by varying emission source characteristics. Based on PMF model, seven source factors for PM2.5 were identified, which were coal combustion + biomass burning, vehicle emission, mineral dust, ship emission, sea salt, industry source, refined chrome industry with the contribution of 48.21%, 30.33%, 7.24%, 6.63%, 3.51%, 3.2%, and 0.88%, respectively. In addition, PSCF analysis using the daily contribution of each factor from PMF result suggested that Shandong peninsula and Hebei province were identified as the high potential region for coal combustion + biomass burning; Beijing-Tianjin-Hebei (BTH) region was the main source region for industry source; Bohai Sea and East China Sea were found to be of high source potential for ship emission; Geographical region located northwest of BH Island was possessed of high probability for sea salt; Mineral dust presumably came from the region of Mongolia; Refined chrome industry mostly came from Liaoning, Jilin province; The vehicle emission was primarily of BTH region origin, centring on metropolises, such as Beijing and Tianjin. These results provided precious implications for PM2.5 control strategies in North China.

Estimating source-attributable health impacts of ambient fine particulate matter exposure: global premature mortality from surface transportation emissions in 2005

International Nuclear Information System (INIS)

Chambliss, S E; Zeinali, M; Minjares, R; Silva, R; West, J J

2014-01-01

Exposure to ambient fine particular matter (PM 2.5 ) was responsible for 3.2 million premature deaths in 2010 and is among the top ten leading risk factors for early death. Surface transportation is a significant global source of PM 2.5 emissions and a target for new actions. The objective of this study is to estimate the global and national health burden of ambient PM 2.5 exposure attributable to surface transportation emissions. This share of health burden is called the transportation attributable fraction (TAF), and is assumed equal to the proportional decrease in modeled ambient particulate matter concentrations when surface transportation emissions are removed. National population-weighted TAFs for 190 countries are modeled for 2005 using the MOZART-4 global chemical transport model. Changes in annual average concentration of PM 2.5 at 0.5 × 0.67 degree horizontal resolution are based on a global emissions inventory and removal of all surface transportation emissions. Global population-weighted average TAF was 8.5 percent or 1.75 μg m −3 in 2005. Approximately 242 000 annual premature deaths were attributable to surface transportation emissions, dominated by China, the United States, the European Union and India. This application of TAF allows future Global Burden of Disease studies to estimate the sector-specific burden of ambient PM 2.5 exposure. Additional research is needed to capture intraurban variations in emissions and exposure, and to broaden the range of health effects considered, including the effects of other pollutants. (letter)

Source and chemical species characterization of PM10 and human health risk assessment of semi-urban, urban and industrial areas of West Bengal, India.

Science.gov (United States)

Ghosh, Suraj; Rabha, Rumi; Chowdhury, Mallika; Padhy, Pratap Kumar

2018-09-01

Levels of particulate matter of size ten micron (PM 10 ) in outdoor air, potential PM 10 -bound seven metals - manganese, zinc, cadmium, lead, copper, nickel and cobalt - and twelve water-soluble organic and inorganic ionic components - fluoride, acetate, chloride, nitrite, bromide, nitrate, phosphate, sulfate, oxalate, sodium, potassium and calcium - were investigated during two different season. Atmospheric PM 10 samples were collected concurrently from three different sites, i.e., Durgapur (Industrial), Berhampore (Urban) and Bolpur (Semi-urban), West Bengal, India, during summer (April-June 2014) and winter (December 2014-February 2015). Average PM 10 levels were found to be in the range of 189.58-219.96 μg/m 3 at the semi-urban site, 293.41-324.27 μg/m 3 at the urban site and 316.93-344.69 μg/m 3 at the industrial site during summer and winter season respectively. Data on metals and water soluble ions were analyzed statistically (Principal Component Analysis and Factor Analysis) for their source identification and apportionment in the study areas. Principle component analysis models, from three different sites, identified four different factors which share common sources, viz., soil & road re-suspension, motor vehicle and traffic, waste dumping, biomass aerosols, and construction. The pollution load and health risk assessments of selected metals were undertaken in three different sites, within children and adults of the study areas, and were found to be within the safe range. Furthermore, an attempt has also been made to provide basic information on pollution, their sources and exposure pathways for humans in the vicinity of semi-urban, urban and industrial regions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Environmental pollution: quantitative analysis of particulate matter (PM10) by SR-TXRF

International Nuclear Information System (INIS)

Moreira, Silvana; Melo Junior, Ariston da Silva; Zucchi, Orgheda Luiza Araujo Domingues; Vives, Ana Elisa Sirito de

2007-01-01

The atmospheric pollution is a concern in the great urban centers, due its association with man pathologies. The Campinas region is one of the most urbanized of the Sao Paulo State and an important industrial center. Thus, due to its location and importance were installed three samplers for particulate material (PM 10 ). One sampler was located in downtown of Campinas city, in an avenue with high vehicular flow. Another sampler was installed in the UNICAMP campus and the third one in Paulinia city, near to REPLAN. For downtown of Campinas city PM 10 concentrations higher than regular air quality established by CETESB (150 μg.m -3 ) was observed. The PM 10 values for Paulinia and downtown of Campinas were higher than Barao Geraldo location. Employing SR-TXRF was possible identify and quantify 19 elements in the particulate material samples. All the measurements were performed at Synchrotron Light Source Laboratory, Campinas, SP. After statistics analysis by principal components and cluster analysis was possible to assemble the elements according emission sources. The dusty soil for coarse fraction contributed with 62%, 51% and 46% for Barao Geraldo, Paulinia and downtown of Campinas, respectively. The vehicular emission was responsible for 16% at downtown Campinas city as expected due to high vehicular flow at sampling place. The vehicular and industrial emissions contributed with 20% and 25%, respectively at Paulinia sampling site. The industrial emissions observed for Barao Geraldo and downtown of Campinas city were 27% and 33%, respectively. (author)

PM4 crystalline silica emission factors and ambient concentrations at aggregate-producing sources in California.

Science.gov (United States)

Richards, John R; Brozell, Todd T; Rea, Charles; Boraston, Geoff; Hayden, John

2009-11-01

The California Construction and Industrial Minerals Association and the National Stone, Sand, & Gravel Association have sponsored tests at three sand and gravel plants in California to compile crystalline silica emission factors for particulate matter (PM) of aerodynamic diameter of 4 microm or less (PM4) and ambient concentration data. This information is needed by industrial facilities to evaluate compliance with the Chronic Reference Exposure Level (REL) for ambient crystalline silica adopted in 2005 by the California Office of Environmental Health Hazard Assessment. The REL applies to PM4 respirable PM. Air Control Techniques, P.C. sampled for PM4 crystalline silica using a conventional sampler for PM of aerodynamic diameter of 2.5 microm or less (PM2.5), which met the requirements of 40 Code of Federal Regulations Part 50, Appendix L. The sample flow rate was adjusted to modify the 50% cut size to 4 microm instead of 2.5 microm. The filter was also changed to allow for crystalline silica analyses using National Institute for Occupational Safety and Health (NIOSH) Method 7500. The particle size-capture efficiency curve for the modified Appendix L instrument closely matched the performance curve of NIOSH Method 0600 for PM4 crystalline silica and provided a minimum detection limit well below the levels attainable with NIOSH Method 0600. The results of the tests indicate that PM4 crystalline silica emissions range from 0.000006 to 0.000110 lb/t for screening operations, tertiary crushers, and conveyor transfer points. The PM4 crystalline silica emission factors were proportional to the crystalline silica content of the material handled in the process equipment. Measured ambient concentrations ranged from 0 (below detectable limit) to 2.8 microg/m3. All values measured above 2 microg/m3 were at locations upwind of the facilities being tested. The ambient PM4 crystalline silica concentrations measured during this study were below the California REL of 3 microg/m3

Nepal Ambient Monitoring and Source Testing Experiment (NAMaSTE): Emissions of particulate matter from garbage burning, wood and dung cooking fires, motorcycles and brick kilns

Science.gov (United States)

Jayarathne, T. S.; Rathnayake, C.; Stockwell, C.; Daugherty, K.; Islam, R. M.; Christian, T. J.; Bhave, P.; Praveen, P. S.; Panday, A. K.; Adhikari, S.; Rasmi, M.; Goetz, D.; DeCarlo, P. F.; Saikawa, E.; Yokelson, R. J.; Stone, E. A.

2016-12-01

The Nepal Ambient Monitoring and Source Testing Experiment (NAMASTE) field campaign targeted the in-situ characterization of widespread and under-sampled combustion sources in South Asia by determining emission factors (EF) for fine particulate matter (PM2.5), organic carbon (OC), elemental carbon, inorganic ions, trace metals, and organic species. Garbage burning had the highest EF PM2.5 among the sampled sources ranging 7-124 g kg-1, with maximum EFs for garbage burned under higher moisture conditions. Garbage burning emissions contained high concentrations of polycyclic aromatic compounds (PAHs) and heavy metals (Pb, Cd, Zn) that are associated with acute and chronic health effects. Triphenylbenzene and antimony (Sb) were unique to garbage burning are good candidates for tracing this source. Cook stove emissions varied largely by stove technology (traditional mud stove, 3-stone cooking fire, chimney stove, etc.) and biomass fuel (dung, hardwood, twigs, and mixtures thereof). Burning dung consistently emitted more PM2.5 than burning wood and contained characteristic fecal sterols and stanols. Motorcycle emissions were evaluated before and after servicing, which decreased EF PM2.5 from 8.8 g kg-1 to 0.7 g kg-1. Organic species analysis indicated that this reduction in PM2.5­ is largely due to a decrease in emission of motor oil. For brick kilns, the forced draft zig-zag kilns had higher EF PM2.5 (12-19 g kg-1) compared to clamp kilns (8-13 g kg-1) and also exhibited chemical differences. PM2.5 emitted from the zig-zag kiln were mainly OC (7%), sulfate (32%) and uncharacterized chemical components (60%), while clamp kiln emissions were dominated by OC (64%) and ammonium sulfate (36%). The quantitative emission factors developed in this study may be used for source apportionment and to update regional emission inventories.

Chemical characteristics and source apportionment of PM2.5 in Lanzhou, China.

Science.gov (United States)

Tan, Jihua; Zhang, Leiming; Zhou, Xueming; Duan, Jingchun; Li, Yan; Hu, Jingnan; He, Kebin

2017-12-01