Numerical analysis of the resonance mechanism of the lumped parameter system model for acoustic mine detection

International Nuclear Information System (INIS)

Wang Chi; Zhou Yu-Qiu; Shen Gao-Wei; Wu Wen-Wen; Ding Wei

2013-01-01

The method of numerical analysis is employed to study the resonance mechanism of the lumped parameter system model for acoustic mine detection. Based on the basic principle of the acoustic resonance technique for mine detection and the characteristics of low-frequency acoustics, the ''soil-mine'' system could be equivalent to a damping ''mass-spring'' resonance model with a lumped parameter analysis method. The dynamic simulation software, Adams, is adopted to analyze the lumped parameter system model numerically. The simulated resonance frequency and anti-resonance frequency are 151 Hz and 512 Hz respectively, basically in agreement with the published resonance frequency of 155 Hz and anti-resonance frequency of 513 Hz, which were measured in the experiment. Therefore, the technique of numerical simulation is validated to have the potential for analyzing the acoustic mine detection model quantitatively. The influences of the soil and mine parameters on the resonance characteristics of the soil—mine system could be investigated by changing the parameter setup in a flexible manner. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Modelling of nonhomogeneous atmosphere in NPP containment using lumped-parameter model based on CFD calculations

International Nuclear Information System (INIS)

Kljenak, I.; Mavko, B.; Babic, M.

2005-01-01

Full text of publication follows: The modelling and simulation of atmosphere mixing and stratification in nuclear power plant containments is a topic, which is currently being intensely investigated. With the increase of computer power, it has now become possible to model these phenomena with a local instantaneous description, using so-called Computational Fluid Dynamics (CFD) codes. However, calculations with these codes still take relatively long times. An alternative faster approach, which is also being applied, is to model nonhomogeneous atmosphere with lumped-parameter codes by dividing larger control volumes into smaller volumes, in which conditions are modelled as homogeneous. The flow between smaller volumes is modelled using one-dimensional approaches, which includes the prescription of flow loss coefficients. However, some authors have questioned this approach, as it appears that atmosphere stratification may sometimes be well simulated only by adjusting flow loss coefficients to adequate 'artificial' values that are case-dependent. To start the resolution of this issue, a modelling of nonhomogeneous atmosphere with a lumped-parameter code is proposed, where the subdivision of a large volume into smaller volumes is based on results of CFD simulations. The basic idea is to use the results of a CFD simulation to define regions, in which the flow velocities have roughly the same direction. These regions are then modelled as control volumes in a lumped-parameter model. In the proposed work, this procedure was applied to a simulation of an experiment of atmosphere mixing and stratification, which was performed in the TOSQAN facility. The facility is located at the Institut de Radioprotection et de Surete Nucleaire (IRSN) in Saclay (France) and consists of a cylindrical vessel (volume: 7 m3), in which gases are injected. In the experiment, which was also proposed for the OECD/NEA International Standard Problem No.47, air was initially present in the vessel, and

Lumped Parameter Modeling for Rapid Vibration Response Prototyping and Test Correlation for Electronic Units

Science.gov (United States)

Van Dyke, Michael B.

2013-01-01

Present preliminary work using lumped parameter models to approximate dynamic response of electronic units to random vibration; Derive a general N-DOF model for application to electronic units; Illustrate parametric influence of model parameters; Implication of coupled dynamics for unit/board design; Demonstrate use of model to infer printed wiring board (PWB) dynamics from external chassis test measurement.

Lumped-parameter modeling of PWR downcomer and pressurizer for LOCA conditions

International Nuclear Information System (INIS)

Rohatgi, U.S.; Saha, P.; Dubow, A.A.

1978-01-01

Two lumped-parameter models, one for a PWR downcomer and the other for a pressurizer, are presented. The models are based on the transient, nonhomogeneous, drift-flux description of two-phase flow, and are suitable for simulating a hypothetical LOCA condition. Effects of thermal nonequilibrium are incorporated in the downcomer model, whereas the pressurizer model can track the interfaces among various flow regimes. Semiimplicit numerical schemes are used for solution. Encouraging results have been obtained for both the models. (author)

A lumped parameter, low dimension model of heat exchanger

International Nuclear Information System (INIS)

Kanoh, Hideaki; Furushoo, Junji; Masubuchi, Masami

1980-01-01

This paper reports on the results of investigation of the distributed parameter model, the difference model, and the model of the method of weighted residuals for heat exchangers. By the method of weighted residuals (MWR), the opposite flow heat exchanger system is approximated by low dimension, lumped parameter model. By assuming constant specific heat, constant density, the same form of tube cross-section, the same form of the surface of heat exchange, uniform flow velocity, the linear relation of heat transfer to flow velocity, liquid heat carrier, and the thermal insulation of liquid from outside, fundamental equations are obtained. The experimental apparatus was made of acrylic resin. The response of the temperature at the exit of first liquid to the variation of the flow rate of second liquid was measured and compared with the models. The MWR model shows good approximation for the low frequency region, and as the number of division increases, good approximation spreads to higher frequency region. (Kato, T.)

Lumped-parameter fuel rod model for rapid thermal transients

International Nuclear Information System (INIS)

Perkins, K.R.; Ramshaw, J.D.

1975-07-01

The thermal behavior of fuel rods during simulated accident conditions is extremely sensitive to the heat transfer coefficient which is, in turn, very sensitive to the cladding surface temperature and the fluid conditions. The development of a semianalytical, lumped-parameter fuel rod model which is intended to provide accurate calculations, in a minimum amount of computer time, of the thermal response of fuel rods during a simulated loss-of-coolant accident is described. The results show good agreement with calculations from a comprehensive fuel-rod code (FRAP-T) currently in use at Aerojet Nuclear Company

Importance theory for lumped-parameter systems

International Nuclear Information System (INIS)

Cady, K.B.; Kenton, M.A.; Ward, J.C.; Piepho, M.G.

1981-01-01

A general sensitivity theory has been developed for nonlinear lumped parameter system simulations. The point of departure is general perturbation theory for nonlinear systems. Importance theory as developed here allows the calculation of the sensitivity of a response function to any physical or design parameter; importance of any equation or term or physical effect in the system model on the response function; variance of the response function caused by the variances and covariances of all physical parameters; and approximate effect on the response function of missing physical phenomena or incorrect parameters

Lumped Parameter Models of the Central Nervous System for VIIP Research

Science.gov (United States)

Vera, J.; Mulugeta, L.; Nelson, E. S.; Raykin, J.; Feola, A.; Gleason, R.; Samuels, B.; Myers, J. G.

2015-01-01

INTRODUCTION: Current long-duration missions to the International Space Station and future exploration-class missions beyond low-Earth orbit, such as to Mars and asteroids, expose astronauts to increased risk of Visual Impairment and Intracranial Pressure (VIIP) syndrome [1]. It has been hypothesized that the headward shift of cerebral spinal fluid (CSF) and blood in microgravity may cause significant elevation of intracranial pressure (ICP), which in turn induces VIIP syndrome through biomechanical pathways [1, 2]. However, there is insufficient evidence to confirm this hypothesis. In this light, we are developing lumped-parameter models of fluid transport in the central nervous system (CNS) as a means to simulate the influence of microgravity on ICP. The CNS models will also be used in concert with the lumped parameter and finite element models of the eye described in the realted IWS abstracts submitted by Nelson et al., Feola et al. and Ethier et al. METHODS: We have developed a nine compartment CNS model (Figure 1) capable of both time-dependent and steady state fluid transport simulations, based on the works of Stevens et al. [3]. The breakdown of compartments within the model includes: vascular (3), CSF (2), brain (1) and extracranial (3). The boundary pressure in the Central Arteries [A] node is prescribed using an oscillating pressure function PA(t) simulating the carotid pulsatile pressure wave as developed by Linninger et al. [4]. For each time step, pressures are integrated through time using an adaptive-timestep 4th and 5th order Runga-Kutta solver. Once pressures are found, constitutive equations are used to solve for flowrates (Q) between each compartment. In addition to fluid flow between the different compartments, compliance (C) interactions between neighboring compartments are represented. We are also developing a second CNS model based on the works of Linninger et al. [4] which takes a more granular approach to represent the interactions of the

Simulation of hydrogen deflagration experiment – Benchmark exercise with lumped-parameter codes

Energy Technology Data Exchange (ETDEWEB)

Kljenak, Ivo, E-mail: ivo.kljenak@ijs.si [Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Kuznetsov, Mikhail, E-mail: mike.kuznetsov@kit.edu [Karlsruhe Institute of Technology, Kaiserstraße 12, 76131 Karlsruhe (Germany); Kostka, Pal, E-mail: kostka@nubiki.hu [NUBIKI Nuclear Safety Research Institute, Konkoly-Thege Miklós út 29-33, 1121 Budapest (Hungary); Kubišova, Lubica, E-mail: lubica.kubisova@ujd.gov.sk [Nuclear Regulatory Authority of the Slovak Republic, Bajkalská 27, 82007 Bratislava (Slovakia); Maltsev, Mikhail, E-mail: maltsev_MB@aep.ru [JSC Atomenergoproekt, 1, st. Podolskykh Kursantov, Moscow (Russian Federation); Manzini, Giovanni, E-mail: giovanni.manzini@rse-web.it [Ricerca sul Sistema Energetico, Via Rubattino 54, 20134 Milano (Italy); Povilaitis, Mantas, E-mail: mantas.p@mail.lei.lt [Lithuania Energy Institute, Breslaujos g.3, 44403 Kaunas (Lithuania)

2015-03-15

Highlights: • Blind and open simulations of hydrogen combustion experiment in large-scale containment-like facility with different lumped-parameter codes. • Simulation of axial as well as radial flame propagation. • Confirmation of adequacy of lumped-parameter codes for safety analyses of actual nuclear power plants. - Abstract: An experiment on hydrogen deflagration (Upward Flame Propagation Experiment – UFPE) was proposed by the Jozef Stefan Institute (Slovenia) and performed in the HYKA A2 facility at the Karlsruhe Institute of Technology (Germany). The experimental results were used to organize a benchmark exercise for lumped-parameter codes. Six organizations (JSI, AEP, LEI, NUBIKI, RSE and UJD SR) participated in the benchmark exercise, using altogether four different computer codes: ANGAR, ASTEC, COCOSYS and ECART. Both blind and open simulations were performed. In general, all the codes provided satisfactory results of the pressure increase, whereas the results of the temperature show a wider dispersal. Concerning the flame axial and radial velocities, the results may be considered satisfactory, given the inherent simplification of the lumped-parameter description compared to the local instantaneous description.

Simulation of hydrogen deflagration experiment – Benchmark exercise with lumped-parameter codes

International Nuclear Information System (INIS)

Kljenak, Ivo; Kuznetsov, Mikhail; Kostka, Pal; Kubišova, Lubica; Maltsev, Mikhail; Manzini, Giovanni; Povilaitis, Mantas

2015-01-01

Highlights: • Blind and open simulations of hydrogen combustion experiment in large-scale containment-like facility with different lumped-parameter codes. • Simulation of axial as well as radial flame propagation. • Confirmation of adequacy of lumped-parameter codes for safety analyses of actual nuclear power plants. - Abstract: An experiment on hydrogen deflagration (Upward Flame Propagation Experiment – UFPE) was proposed by the Jozef Stefan Institute (Slovenia) and performed in the HYKA A2 facility at the Karlsruhe Institute of Technology (Germany). The experimental results were used to organize a benchmark exercise for lumped-parameter codes. Six organizations (JSI, AEP, LEI, NUBIKI, RSE and UJD SR) participated in the benchmark exercise, using altogether four different computer codes: ANGAR, ASTEC, COCOSYS and ECART. Both blind and open simulations were performed. In general, all the codes provided satisfactory results of the pressure increase, whereas the results of the temperature show a wider dispersal. Concerning the flame axial and radial velocities, the results may be considered satisfactory, given the inherent simplification of the lumped-parameter description compared to the local instantaneous description

An Integrated Lumped Parameter-CFD approach for off-design ejector performance evaluation

International Nuclear Information System (INIS)

Besagni, Giorgio; Mereu, Riccardo; Chiesa, Paolo; Inzoli, Fabio

2015-01-01

Highlights: • We validate a CFD approach for a convergent nozzle ejector using global and local measurement. • We evaluate seven RANS turbulence models for convergent nozzle ejector. • We introduce a lumped parameter model for on-design and off-design ejector performance evaluation. • We analyze the relationship between local flow behavior and lumped parameters of the model. • We discuss how to improve predicting capabilities of the model by variable parameters calibrated on CFD simulations. - Abstract: This paper presents an Integrated Lumped Parameter Model-Computational Fluid-Dynamics approach for off-design ejector performance evaluation. The purpose of this approach is to evaluate the entrainment ratio, for a fixed geometry, in both on-design and off-design operating conditions. The proposed model is based on a Lumped Parameter Model (LPM) with variable ejector component efficiencies provided by CFD simulations. The CFD results are used for developing maps for ejector component efficiencies in a broad range of operating conditions. The ejector component efficiency maps couple the CFD and the LPM techniques for building an Integrated LPM-CFD approach. The proposed approach is demonstrated for a convergent nozzle ejector and the paper is structured in four parts. At first, the CFD approach is validated by global and local data and seven Reynolds Averaged Navier Stokes (RANS) turbulence models are compared: the k–ω SST showed good performance and was selected for the rest of the analysis. At second, a Lumped Parameter Model (LPM) for subsonic ejector is developed and the ejector component efficiencies have been defined. At third, the CFD approach is used to investigate the flow field, to analyze its influence on ejector component efficiencies and to propose efficiency correlations and maps linking ejector component efficiencies and local flow quantities. In the last part, the efficiency maps are embedded into the lumped parameter model, thus creating

MEMS 3-DoF gyroscope design, modeling and simulation through equivalent circuit lumped parameter model

International Nuclear Information System (INIS)

Mian, Muhammad Umer; Khir, M. H. Md.; Tang, T. B.; Dennis, John Ojur; Riaz, Kashif; Iqbal, Abid; Bazaz, Shafaat A.

2015-01-01

Pre-fabrication, behavioural and performance analysis with computer aided design (CAD) tools is a common and fabrication cost effective practice. In light of this we present a simulation methodology for a dual-mass oscillator based 3 Degree of Freedom (3-DoF) MEMS gyroscope. 3-DoF Gyroscope is modeled through lumped parameter models using equivalent circuit elements. These equivalent circuits consist of elementary components which are counterpart of their respective mechanical components, used to design and fabricate 3-DoF MEMS gyroscope. Complete designing of equivalent circuit model, mathematical modeling and simulation are being presented in this paper. Behaviors of the equivalent lumped models derived for the proposed device design are simulated in MEMSPRO T-SPICE software. Simulations are carried out with the design specifications following design rules of the MetalMUMPS fabrication process. Drive mass resonant frequencies simulated by this technique are 1.59 kHz and 2.05 kHz respectively, which are close to the resonant frequencies found by the analytical formulation of the gyroscope. The lumped equivalent circuit modeling technique proved to be a time efficient modeling technique for the analysis of complex MEMS devices like 3-DoF gyroscopes. The technique proves to be an alternative approach to the complex and time consuming couple field analysis Finite Element Analysis (FEA) previously used

MEMS 3-DoF gyroscope design, modeling and simulation through equivalent circuit lumped parameter model

Energy Technology Data Exchange (ETDEWEB)

Mian, Muhammad Umer, E-mail: umermian@gmail.com; Khir, M. H. Md.; Tang, T. B. [Department of Electrical and Electronic Engineering, Universiti Teknologi PETRONAS, Tronoh, Perak (Malaysia); Dennis, John Ojur [Department of Fundamental & Applied Sciences, Universiti Teknologi PETRONAS, Tronoh, Perak (Malaysia); Riaz, Kashif; Iqbal, Abid [Faculty of Electronics Engineering, GIK Institute of Engineering Sciences and Technology, Topi, Khyber Pakhtunkhaw (Pakistan); Bazaz, Shafaat A. [Department of Computer Science, Center for Advance Studies in Engineering, Islamabad (Pakistan)

2015-07-22

Pre-fabrication, behavioural and performance analysis with computer aided design (CAD) tools is a common and fabrication cost effective practice. In light of this we present a simulation methodology for a dual-mass oscillator based 3 Degree of Freedom (3-DoF) MEMS gyroscope. 3-DoF Gyroscope is modeled through lumped parameter models using equivalent circuit elements. These equivalent circuits consist of elementary components which are counterpart of their respective mechanical components, used to design and fabricate 3-DoF MEMS gyroscope. Complete designing of equivalent circuit model, mathematical modeling and simulation are being presented in this paper. Behaviors of the equivalent lumped models derived for the proposed device design are simulated in MEMSPRO T-SPICE software. Simulations are carried out with the design specifications following design rules of the MetalMUMPS fabrication process. Drive mass resonant frequencies simulated by this technique are 1.59 kHz and 2.05 kHz respectively, which are close to the resonant frequencies found by the analytical formulation of the gyroscope. The lumped equivalent circuit modeling technique proved to be a time efficient modeling technique for the analysis of complex MEMS devices like 3-DoF gyroscopes. The technique proves to be an alternative approach to the complex and time consuming couple field analysis Finite Element Analysis (FEA) previously used.

Lumped parameter modeling of a two-phase thermal-hydraulic channel with interface tracking

International Nuclear Information System (INIS)

Jo, J.H.; Kaufman, J.M.; Ruger, C.J.; Stein, S.

1978-01-01

A nonhomogenous, thermal nonequilibrium model for one-dimensional two-phase flow in a heated channel has been formulated in lumped parameter form. The channel is divided into a variable number of flow regimes separated by moving interfaces. The model can be used to predict the behavior of a LWR core and both primary and secondary sides of a steam generator under transient conditions. (author)

Method for Lumped Parameter simulation of Digital Displacement pumps/motors based on CFD

DEFF Research Database (Denmark)

Rømer, Daniel; Johansen, Per; Pedersen, Henrik C.

2013-01-01

Digital displacement fluid power pumps/motors offers improved efficiency and performance compared to traditional variable displacement pump/motors. These improvements are made possible by using efficient electronically controlled seat valves and careful design of the flow geometry. To optimize...... the design and control of digital displacement machines, there is a need for simulation models, preferably models with low computational cost. Therefore, a low computational cost generic lumped parameter model of digital displacement machine is presented, including a method for determining the needed model...... parameters based on steady CFD results, in order to take detailed geometry information into account. The response of the lumped parameter model is compared to a computational expensive transient CFD model for an example geometry....

The application of model with lumped parameters for transient condition analyses of NPP; Primena modela sa koncentrisanim parametrima za analize pelaznih stanja nukleane elektrane

Energy Technology Data Exchange (ETDEWEB)

Stankovic, B [Institut GOSA, Beograd (Yugoslavia); Stevanovic, V [Masinski fakultet, Beograd (Yugoslavia)

1985-07-01

The transient behaviour of NPP Krsko during the accident of pressurizer spray valve stuck open has been simulated y lumped parameters model of the PWR coolant system components, developed at the faculty of Mechanical Engineering, University of Belgrade. The elementary volumes which are characterised by the process and state parameters, and by junctions which are characterised by the geometrical and flow parameters are basic structure of physical model. The process parameters obtained by the model RESI, show qualitative agreement with the measured valves, in a degree in which the actions of reactor safety engineered system and emergency core cooling system are adequately modelled; in spite of the elementary physical model structure and only the modelling of thermal process in reactor core and equilibrium conditions of pressurizer and steam generator. The pressurizer pressure and liquid level predicted by the non-equilibrium pressurizer model SOP show good agreement until the HIPS (high pressure pumps) is activated. (author)

Lumped parametric model of the human ear for sound transmission.

Science.gov (United States)

Feng, Bin; Gan, Rong Z

2004-09-01

A lumped parametric model of the human auditoria peripherals consisting of six masses suspended with six springs and ten dashpots was proposed. This model will provide the quantitative basis for the construction of a physical model of the human middle ear. The lumped model parameters were first identified using published anatomical data, and then determined through a parameter optimization process. The transfer function of the middle ear obtained from human temporal bone experiments with laser Doppler interferometers was used for creating the target function during the optimization process. It was found that, among 14 spring and dashpot parameters, there were five parameters which had pronounced effects on the dynamic behaviors of the model. The detailed discussion on the sensitivity of those parameters was provided with appropriate applications for sound transmission in the ear. We expect that the methods for characterizing the lumped model of the human ear and the model parameters will be useful for theoretical modeling of the ear function and construction of the ear physical model.

Development of a transient, lumped hydrologic model for geomorphologic units in a geomorphology based rainfall-runoff modelling framework

Science.gov (United States)

Vannametee, E.; Karssenberg, D.; Hendriks, M. R.; de Jong, S. M.; Bierkens, M. F. P.

2010-05-01

We propose a modelling framework for distributed hydrological modelling of 103-105 km2 catchments by discretizing the catchment in geomorphologic units. Each of these units is modelled using a lumped model representative for the processes in the unit. Here, we focus on the development and parameterization of this lumped model as a component of our framework. The development of the lumped model requires rainfall-runoff data for an extensive set of geomorphological units. Because such large observational data sets do not exist, we create artificial data. With a high-resolution, physically-based, rainfall-runoff model, we create artificial rainfall events and resulting hydrographs for an extensive set of different geomorphological units. This data set is used to identify the lumped model of geomorphologic units. The advantage of this approach is that it results in a lumped model with a physical basis, with representative parameters that can be derived from point-scale measurable physical parameters. The approach starts with the development of the high-resolution rainfall-runoff model that generates an artificial discharge dataset from rainfall inputs as a surrogate of a real-world dataset. The model is run for approximately 105 scenarios that describe different characteristics of rainfall, properties of the geomorphologic units (i.e. slope gradient, unit length and regolith properties), antecedent moisture conditions and flow patterns. For each scenario-run, the results of the high-resolution model (i.e. runoff and state variables) at selected simulation time steps are stored in a database. The second step is to develop the lumped model of a geomorphological unit. This forward model consists of a set of simple equations that calculate Hortonian runoff and state variables of the geomorphologic unit over time. The lumped model contains only three parameters: a ponding factor, a linear reservoir parameter, and a lag time. The model is capable of giving an appropriate

Improved lumped parameter for annular fuel element thermohydraulic analysis

International Nuclear Information System (INIS)

Duarte, Juliana Pacheco; Su, Jian; Alvim, Antonio Carlos Marques

2011-01-01

Annular fuel elements have been intensively studied for the purpose of increasing power density in light water reactors (LWR). This paper presents an improved lumped parameter model for the dynamics of a LWR core with annular fuel elements, composed of three sub-models: the fuel dynamics model, the neutronics model, and the coolant energy balance model. The transient heat conduction in radial direction is analyzed through an improved lumped parameter formulation. The Hermite approximation for integration is used to obtain the average temperature of the fuel and cladding and also to obtain the average heat flux. The volumetric heat generation in fuel rods was obtained with the point kinetics equations with six delayed neutron groups. The equations for average temperature of fuel and cladding are solved along with the point kinetic equations, assuming linear reactivity and coolant temperature in cases of reactivity insertion. The analytical development of the model and the numeric solution of the ordinary differential equation system were obtained by using Mathematica 7.0. The dynamic behaviors for average temperatures of fuel, cladding and coolant in transient events as well as the reactor power were analyzed. (author)

Rigorous theoretical derivation of lumped models to transmission line systems

International Nuclear Information System (INIS)

Zhao Jixiang

2012-01-01

By virtue of the negative electric parameter concept, i.e. negative lumped resistance, inductance, conductance and capacitance (N-RLGC), the lumped equivalent models of transmission line systems, including the circuit model, two-port π-network and T-network, are given. We start from the N-segment-ladder-like equivalent networks composed distributed parameters, and achieve the input impedance in the form of a continued fraction. Utilizing the continued fraction theory, the expressions of input impedance are obtained under three kinds of extreme cases, i.e. the load impedances are equal to zero, infinity and characteristic impedance, respectively. When the number of segment N is limited to infinity, they are transformed to lumped elements. Comparison between the distributed model and lumped model of transmission lines, the expression of tanh γd, which is the key term in the transmission line equations, are obtained by RLGC, furthermore, according to input admittance, admittance matrix and ABCD matrix of transmission lines, the lumped equivalent circuit models, π-networks and T-networks have been given. The models are verified in the frequency and time domain, respectively, showing that the models are accurate and efficient. (semiconductor integrated circuits)

Measurement of Hydrologic Streamflow Metrics and Estimation of Streamflow with Lumped Parameter Models in a Managed Lake System, Sebago Lake, Maine

Science.gov (United States)

Reeve, A. S.; Martin, D.; Smith, S. M.

2013-12-01

Surface waters within the Sebago Lake watershed (southern Maine, USA) provide a variety of economically and intrinsically valuable recreational, commercial and environmental services. Different stakeholder groups for the 118 km2 Sebago Lake and surrounding watershed advocate for different lake and watershed management strategies, focusing on the operation of a dam at the outflow from Sebago Lake. While lake level in Sebago Lake has been monitored for over a century, limited data is available on the hydrologic processes that drive lake level and therefore impact how dam operation (and other changes to the region) will influence the hydroperiod of the lake. To fill this information gap several tasks were undertaken including: 1) deploying data logging pressure transducers to continuously monitor stream stage in nine tributaries, 2) measuring stream discharge at these sites to create rating curves for the nine tributaries, and using the resulting continuous discharge records to 3) calibrate lumped parameter computer models based on the GR4J model, modified to include a degree-day snowmelt routine. These lumped parameter models have been integrated with a simple lake water-balance model to estimate lake level and its response to different scenarios including dam management strategies. To date, about three years of stream stage data have been used to estimate stream discharge in all monitored tributaries (data collection is ongoing). Baseflow separation indices (BFI) for 2010 and 2011 using the USGS software PART and the Eckhart digital filter in WHAT range from 0.80-0.86 in the Crooked River and Richmill Outlet,followed by Northwest (0.75) and Muddy (0.53-0.56) Rivers, with the lowest BFI measured in Sticky River (0.41-0.56). The BFI values indicate most streams have significant groundwater (or other storage) inputs. The lumped parameter watershed model has been calibrated for four streams (Nash-Sutcliffe = 0.4 to 0.9), with the other major tributaries containing

Improved lumped models for transient combined convective and radiative cooling of multi-layer composite slabs

International Nuclear Information System (INIS)

An Chen; Su Jian

2011-01-01

Improved lumped parameter models were developed for the transient heat conduction in multi-layer composite slabs subjected to combined convective and radiative cooling. The improved lumped models were obtained through two-point Hermite approximations for integrals. Transient combined convective and radiative cooling of three-layer composite slabs was analyzed to illustrate the applicability of the proposed lumped models, with respect to different values of the Biot numbers, the radiation-conduction parameter, the dimensionless thermal contact resistances, the dimensionless thickness, and the dimensionless thermal conductivity. It was shown by comparison with numerical solution of the original distributed parameter model that the higher order lumped model (H 1,1 /H 0,0 approximation) yielded significant improvement of average temperature prediction over the classical lumped model. In addition, the higher order (H 1,1 /H 0,0 ) model was applied to analyze the transient heat conduction problem of steel-concrete-steel sandwich plates. - Highlights: → Improved lumped models for convective-radiative cooling of multi-layer slabs were developed. → Two-point Hermite approximations for integrals were employed. → Significant improvement over classical lumped model was achieved. → The model can be applied to high Biot number and high radiation-conduction parameter. → Transient heat conduction in steel-concrete-steel sandwich pipes was analyzed as an example.

Lumping procedure for a kinetic model of catalytic naphtha reforming

Directory of Open Access Journals (Sweden)

H. M. Arani

2009-12-01

Full Text Available A lumping procedure is developed for obtaining kinetic and thermodynamic parameters of catalytic naphtha reforming. All kinetic and deactivation parameters are estimated from industrial data and thermodynamic parameters are calculated from derived mathematical expressions. The proposed model contains 17 lumps that include the C6 to C8+ hydrocarbon range and 15 reaction pathways. Hougen-Watson Langmuir-Hinshelwood type reaction rate expressions are used for kinetic simulation of catalytic reactions. The kinetic parameters are benchmarked with several sets of plant data and estimated by the SQP optimization method. After calculation of deactivation and kinetic parameters, plant data are compared with model predictions and only minor deviations between experimental and calculated data are generally observed.

Genetic Algorithms for Estimating Effective Parameters in a Lumped Reactor Model for Reactivity Predictions

International Nuclear Information System (INIS)

Marseguerra, Marzio; Zio, Enrico

2001-01-01

The control system of a reactor should be able to predict, in real time, the amount of reactivity to be inserted (e.g., by control rod movements and boron injection and dilution) to respond to a given electrical load demand or to undesired, accidental transients. The real-time constraint renders impractical the use of a large, detailed dynamic reactor code. One has, then, to resort to simplified analytical models with lumped effective parameters suitably estimated from the reactor data.The simple and well-known Chernick model for describing the reactor power evolution in the presence of xenon is considered and the feasibility of using genetic algorithms for estimating the effective nuclear parameters involved and the initial nonmeasurable xenon and iodine conditions is investigated. This approach has the advantage of counterbalancing the inherent model simplicity with the periodic reestimation of the effective parameter values pertaining to each reactor on the basis of its recent history. By so doing, other effects, such as burnup, are automatically taken into account

Flexible hydrological modeling - Disaggregation from lumped catchment scale to higher spatial resolutions

Science.gov (United States)

Tran, Quoc Quan; Willems, Patrick; Pannemans, Bart; Blanckaert, Joris; Pereira, Fernando; Nossent, Jiri; Cauwenberghs, Kris; Vansteenkiste, Thomas

2015-04-01

Based on an international literature review on model structures of existing rainfall-runoff and hydrological models, a generalized model structure is proposed. It consists of different types of meteorological components, storage components, splitting components and routing components. They can be spatially organized in a lumped way, or on a grid, spatially interlinked by source-to-sink or grid-to-grid (cell-to-cell) routing. The grid size of the model can be chosen depending on the application. The user can select/change the spatial resolution depending on the needs and/or the evaluation of the accuracy of the model results, or use different spatial resolutions in parallel for different applications. Major research questions addressed during the study are: How can we assure consistent results of the model at any spatial detail? How can we avoid strong or sudden changes in model parameters and corresponding simulation results, when one moves from one level of spatial detail to another? How can we limit the problem of overparameterization/equifinality when we move from the lumped model to the spatially distributed model? The proposed approach is a step-wise one, where first the lumped conceptual model is calibrated using a systematic, data-based approach, followed by a disaggregation step where the lumped parameters are disaggregated based on spatial catchment characteristics (topography, land use, soil characteristics). In this way, disaggregation can be done down to any spatial scale, and consistently among scales. Only few additional calibration parameters are introduced to scale the absolute spatial differences in model parameters, but keeping the relative differences as obtained from the spatial catchment characteristics. After calibration of the spatial model, the accuracies of the lumped and spatial models were compared for peak, low and cumulative runoff total and sub-flows (at downstream and internal gauging stations). For the distributed models, additional

BWR MARK I pressure suppression pool mixing and stratification analysis using GOTHIC lumped parameter modeling methodology

International Nuclear Information System (INIS)

Ozdemir, Ozkan Emre; George, Thomas L.

2015-01-01

As a part of the GOTHIC (GOTHIC incorporates technology developed for the electric power industry under the sponsorship of EPRI.) Fukushima Technical Evaluation project (EPRI, 2014a, b, 2015), GOTHIC (EPRI, 2014c) has been benchmarked against test data for pool stratification (EPRI, 2014a, b, Ozdemir and George, 2013). These tests confirmed GOTHIC’s ability to simulate pool mixing and stratification under a variety of anticipated suppression pool operating conditions. The multidimensional modeling requires long simulation times for events that may occur over a period of hours or days. For these scenarios a lumped model of the pressure suppression chamber is desirable to maintain reasonable simulation times. However, a lumped model for the pool is not able to predict the effects of pool stratification that can influence the overall containment response. The main objective of this work is on the development of a correlation that can be used to estimate pool mixing and stratification effects in a lumped modeling approach. A simplified lumped GOTHIC model that includes a two zone model for the suppression pool with controlled circulation between the upper and lower zones was constructed. A pump and associated flow connections are included to provide mixing between the upper and lower pool volumes. Using numerically generated data from a multidimensional GOTHIC model for the suppression pool, a correlation was developed for the mixing rate between the upper and lower pool volumes in a two-zone, lumped model. The mixing rate depends on the pool subcooling, the steam injection rate and the injection depth

Deducing Electronic Unit Internal Response During a Vibration Test Using a Lumped Parameter Modeling Approach

Science.gov (United States)

Van Dyke, Michael B.

2014-01-01

During random vibration testing of electronic boxes there is often a desire to know the dynamic response of certain internal printed wiring boards (PWBs) for the purpose of monitoring the response of sensitive hardware or for post-test forensic analysis in support of anomaly investigation. Due to restrictions on internally mounted accelerometers for most flight hardware there is usually no means to empirically observe the internal dynamics of the unit, so one must resort to crude and highly uncertain approximations. One common practice is to apply Miles Equation, which does not account for the coupled response of the board in the chassis, resulting in significant over- or under-prediction. This paper explores the application of simple multiple-degree-of-freedom lumped parameter modeling to predict the coupled random vibration response of the PWBs in their fundamental modes of vibration. A simple tool using this approach could be used during or following a random vibration test to interpret vibration test data from a single external chassis measurement to deduce internal board dynamics by means of a rapid correlation analysis. Such a tool might also be useful in early design stages as a supplemental analysis to a more detailed finite element analysis to quickly prototype and analyze the dynamics of various design iterations. After developing the theoretical basis, a lumped parameter modeling approach is applied to an electronic unit for which both external and internal test vibration response measurements are available for direct comparison. Reasonable correlation of the results demonstrates the potential viability of such an approach. Further development of the preliminary approach presented in this paper will involve correlation with detailed finite element models and additional relevant test data.

Parameter sensitivity analysis of a lumped-parameter model of a chain of lymphangions in series.

Science.gov (United States)

Jamalian, Samira; Bertram, Christopher D; Richardson, William J; Moore, James E

2013-12-01

Any disruption of the lymphatic system due to trauma or injury can lead to edema. There is no effective cure for lymphedema, partly because predictive knowledge of lymphatic system reactions to interventions is lacking. A well-developed model of the system could greatly improve our understanding of its function. Lymphangions, defined as the vessel segment between two valves, are the individual pumping units. Based on our previous lumped-parameter model of a chain of lymphangions, this study aimed to identify the parameters that affect the system output the most using a sensitivity analysis. The system was highly sensitive to minimum valve resistance, such that variations in this parameter caused an order-of-magnitude change in time-average flow rate for certain values of imposed pressure difference. Average flow rate doubled when contraction frequency was increased within its physiological range. Optimum lymphangion length was found to be some 13-14.5 diameters. A peak of time-average flow rate occurred when transmural pressure was such that the pressure-diameter loop for active contractions was centered near maximum passive vessel compliance. Increasing the number of lymphangions in the chain improved the pumping in the presence of larger adverse pressure differences. For a given pressure difference, the optimal number of lymphangions increased with the total vessel length. These results indicate that further experiments to estimate valve resistance more accurately are necessary. The existence of an optimal value of transmural pressure may provide additional guidelines for increasing pumping in areas affected by edema.

Analysis of transient heat conduction in a PWR fuel rod by an improved lumped parameter approach

Energy Technology Data Exchange (ETDEWEB)

Dourado, Eneida Regina G. [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil); Cotta, Renato M. [Coordenacao de Pos-Graduacao e Pesquisa de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Mecanica; Jian, Su, E-mail: eneidadourado@gmail.com, E-mail: sujian@nuclear.ufrj.br, E-mail: cotta@mecanica.ufrj.br [Coordenacao de Pos-Graduacao e Pesquisa de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

2017-07-01

This paper aims to analyze transient heat conduction in a nuclear fuel rod by an improved lumped parameter approach. One-dimensional transient heat conduction is considered, with the circumferential symmetry assumed and the axial conduction neglected. The thermal conductivity and specific heat in the fuel pellet are considered temperature dependent, while the thermophysical properties of the cladding are considered constant. Hermite approximation for integration is used to obtain the average temperature and heat flux in the radial direction. Significant improvement over the classical lumped parameter formulation has been achieved. The proposed model can be also used in dynamic analysis of PWR and nuclear power plant simulators. (author)

Analysis of transient heat conduction in a PWR fuel rod by an improved lumped parameter approach

International Nuclear Information System (INIS)

Dourado, Eneida Regina G.; Cotta, Renato M.; Jian, Su

2017-01-01

This paper aims to analyze transient heat conduction in a nuclear fuel rod by an improved lumped parameter approach. One-dimensional transient heat conduction is considered, with the circumferential symmetry assumed and the axial conduction neglected. The thermal conductivity and specific heat in the fuel pellet are considered temperature dependent, while the thermophysical properties of the cladding are considered constant. Hermite approximation for integration is used to obtain the average temperature and heat flux in the radial direction. Significant improvement over the classical lumped parameter formulation has been achieved. The proposed model can be also used in dynamic analysis of PWR and nuclear power plant simulators. (author)

Analysis of groundwater discharge with a lumped-parameter model, using a case study from Tajikistan

Science.gov (United States)

Pozdniakov, S. P.; Shestakov, V. M.

A lumped-parameter model of groundwater balance is proposed that permits an estimate of discharge variability in comparison with the variability of recharge, by taking into account the influence of aquifer parameters. Recharge-discharge relationships are analysed with the model for cases of deterministic and stochastic recharge time-series variations. The model is applied to study the temporal variability of groundwater discharge in a river valley in the territory of Tajikistan, an independent republic in Central Asia. Résumé Un modèle global de bilan d'eau souterraine a été développé pour estimer la variabilité de l'écoulement par rapport à celle de la recharge, en prenant en compte l'influence des paramètres de l'aquifère. Les relations entre recharge et écoulement sont analysées à l'aide du modèle pour des variations des chroniques de recharge soit déterministes, soit stochastiques. Le modèle est appliquéà l'étude de la variabilité temporelle de l'écoulement souterrain vers une rivière, dans le Tadjikistan, une république indépendante d'Asie centrale. Resumen Se propone un modelo de parámetros concentrados para realizar el balance de aguas subterráneas, el cual permite estimar la variabilidad en la descarga con respecto a la variabilidad en la recarga, en función de los parámetros que caracterizan el acuífero. Las relaciones entre recarga y descarga se analizan con el modelo para distintos casos de series temporales de recarga, tanto deterministas como estocásticas. El modelo se aplica al estudio de la variabilidad temporal de la descarga en un valle aluvial de Tadyikistán, una república independiente del Asia Central.

A new analytical method for estimating lumped parameter constants of linear viscoelastic models from strain rate tests

Science.gov (United States)

Mattei, G.; Ahluwalia, A.

2018-04-01

We introduce a new function, the apparent elastic modulus strain-rate spectrum, E_{app} ( \\dot{ɛ} ), for the derivation of lumped parameter constants for Generalized Maxwell (GM) linear viscoelastic models from stress-strain data obtained at various compressive strain rates ( \\dot{ɛ}). The E_{app} ( \\dot{ɛ} ) function was derived using the tangent modulus function obtained from the GM model stress-strain response to a constant \\dot{ɛ} input. Material viscoelastic parameters can be rapidly derived by fitting experimental E_{app} data obtained at different strain rates to the E_{app} ( \\dot{ɛ} ) function. This single-curve fitting returns similar viscoelastic constants as the original epsilon dot method based on a multi-curve global fitting procedure with shared parameters. Its low computational cost permits quick and robust identification of viscoelastic constants even when a large number of strain rates or replicates per strain rate are considered. This method is particularly suited for the analysis of bulk compression and nano-indentation data of soft (bio)materials.

A partial exponential lumped parameter model to evaluate groundwater age distributions and nitrate trends in long-screened wells

Science.gov (United States)

Jurgens, Bryant; Böhlke, John Karl; Kauffman, Leon J.; Belitz, Kenneth; Esser, Bradley K.

2016-01-01

A partial exponential lumped parameter model (PEM) was derived to determine age distributions and nitrate trends in long-screened production wells. The PEM can simulate age distributions for wells screened over any finite interval of an aquifer that has an exponential distribution of age with depth. The PEM has 3 parameters – the ratio of saturated thickness to the top and bottom of the screen and mean age, but these can be reduced to 1 parameter (mean age) by using well construction information and estimates of the saturated thickness. The PEM was tested with data from 30 production wells in a heterogeneous alluvial fan aquifer in California, USA. Well construction data were used to guide parameterization of a PEM for each well and mean age was calibrated to measured environmental tracer data (3H, 3He, CFC-113, and 14C). Results were compared to age distributions generated for individual wells using advective particle tracking models (PTMs). Age distributions from PTMs were more complex than PEM distributions, but PEMs provided better fits to tracer data, partly because the PTMs did not simulate 14C accurately in wells that captured varying amounts of old groundwater recharged at lower rates prior to groundwater development and irrigation. Nitrate trends were simulated independently of the calibration process and the PEM provided good fits for at least 11 of 24 wells. This work shows that the PEM, and lumped parameter models (LPMs) in general, can often identify critical features of the age distributions in wells that are needed to explain observed tracer data and nonpoint source contaminant trends, even in systems where aquifer heterogeneity and water-use complicate distributions of age. While accurate PTMs are preferable for understanding and predicting aquifer-scale responses to water use and contaminant transport, LPMs can be sensitive to local conditions near individual wells that may be inaccurately represented or missing in an aquifer-scale flow model.

Characterization of the pharmacokinetics of gasoline using PBPK modeling with a complex mixtures chemical lumping approach.

Science.gov (United States)

Dennison, James E; Andersen, Melvin E; Yang, Raymond S H

2003-09-01

Gasoline consists of a few toxicologically significant components and a large number of other hydrocarbons in a complex mixture. By using an integrated, physiologically based pharmacokinetic (PBPK) modeling and lumping approach, we have developed a method for characterizing the pharmacokinetics (PKs) of gasoline in rats. The PBPK model tracks selected target components (benzene, toluene, ethylbenzene, o-xylene [BTEX], and n-hexane) and a lumped chemical group representing all nontarget components, with competitive metabolic inhibition between all target compounds and the lumped chemical. PK data was acquired by performing gas uptake PK studies with male F344 rats in a closed chamber. Chamber air samples were analyzed every 10-20 min by gas chromatography/flame ionization detection and all nontarget chemicals were co-integrated. A four-compartment PBPK model with metabolic interactions was constructed using the BTEX, n-hexane, and lumped chemical data. Target chemical kinetic parameters were refined by studies with either the single chemical alone or with all five chemicals together. o-Xylene, at high concentrations, decreased alveolar ventilation, consistent with respiratory irritation. A six-chemical interaction model with the lumped chemical group was used to estimate lumped chemical partitioning and metabolic parameters for a winter blend of gasoline with methyl t-butyl ether and a summer blend without any oxygenate. Computer simulation results from this model matched well with experimental data from single chemical, five-chemical mixture, and the two blends of gasoline. The PBPK model analysis indicated that metabolism of individual components was inhibited up to 27% during the 6-h gas uptake experiments of gasoline exposures.

Recomputing Causality Assignments on Lumped Process Models When Adding New Simplification Assumptions

Directory of Open Access Journals (Sweden)

Antonio Belmonte

2018-04-01

Full Text Available This paper presents a new algorithm for the resolution of over-constrained lumped process systems, where partial differential equations of a continuous time and space model of the system are reduced into ordinary differential equations with a finite number of parameters and where the model equations outnumber the unknown model variables. Our proposal is aimed at the study and improvement of the algorithm proposed by Hangos-Szerkenyi-Tuza. This new algorithm improves the computational cost and solves some of the internal problems of the aforementioned algorithm in its original formulation. The proposed algorithm is based on parameter relaxation that can be modified easily. It retains the necessary information of the lumped process system to reduce the time cost after introducing changes during the system formulation. It also allows adjustment of the system formulations that change its differential index between simulations.

On the treatment of plane fusion front in lumped parameter thermal models with convection

International Nuclear Information System (INIS)

Le Tellier, R.; Skrzypek, E.; Saas, L.

2017-01-01

Highlights: • Solid phase approximations for a two-phase Stefan fusion problem with convection are analyzed. • A reference solution combines integral conservation eqs and a FE solution of the 1D heat equation. • Numerical results are presented for a transient in light water reactor severe accident analysis. • The models performances are highlighted on fusion transients in terms of Biot and Stefan numbers. - Abstract: Within the framework of lumped parameter models for integral codes, this paper focuses on the modeling of a two-phase Stefan fusion problem with natural convection in the liquid phase. In particular, this specific Stefan problem is of interest when studying corium pool behavior in the framework of light water reactor severe accident analysis. The objective of this research is to analyze the applicability of different approximations related to the modeling of the solid phase in terms of boundary heat flux closure relations. Three different approximations are considered: a quadratic profile based model, a model where a parameter controls the power partitioning at the interface and the steady state conduction assumption. These models are compared with an accurate front-tracking solution of this plane fusion front problem. This “reference” is obtained by combining the same integral conservation equations as the approximate models with a mesh-based solution of the 1D heat equation. Numerical results are discussed for a typical configuration of interest for corium pool analysis. Different fusion transients (constructed from nondimensionalization considerations in terms of Biot and Stefan numbers) are used in order to highlight the potential and limitations of the different approximations.

Analysis of direct contact membrane distillation based on a lumped-parameter dynamic predictive model

KAUST Repository

Karam, Ayman M.; Alsaadi, Ahmad Salem; Ghaffour, NorEddine; Laleg-Kirati, Taous-Meriem

2016-01-01

Membrane distillation (MD) is an emerging technology that has a great potential for sustainable water desalination. In order to pave the way for successful commercialization of MD-based water desalination techniques, adequate and accurate dynamical models of the process are essential. This paper presents the predictive capabilities of a lumped-parameter dynamic model for direct contact membrane distillation (DCMD) and discusses the results under wide range of steady-state and dynamic conditions. Unlike previous studies, the proposed model captures the time response of the spacial temperature distribution along the flow direction. It also directly solves for the local temperatures at the membrane interfaces, which allows to accurately model and calculate local flux values along with other intrinsic variables of great influence on the process, like the temperature polarization coefficient (TPC). The proposed model is based on energy and mass conservation principles and analogy between thermal and electrical systems. Experimental data was collected to validated the steady-state and dynamic responses of the model. The obtained results shows great agreement with the experimental data. The paper discusses the results of several simulations under various conditions to optimize the DCMD process efficiency and analyze its response. This demonstrates some potential applications of the proposed model to carry out scale up and design studies. © 2016

Analysis of direct contact membrane distillation based on a lumped-parameter dynamic predictive model

KAUST Repository

Karam, Ayman M.

2016-10-03

Membrane distillation (MD) is an emerging technology that has a great potential for sustainable water desalination. In order to pave the way for successful commercialization of MD-based water desalination techniques, adequate and accurate dynamical models of the process are essential. This paper presents the predictive capabilities of a lumped-parameter dynamic model for direct contact membrane distillation (DCMD) and discusses the results under wide range of steady-state and dynamic conditions. Unlike previous studies, the proposed model captures the time response of the spacial temperature distribution along the flow direction. It also directly solves for the local temperatures at the membrane interfaces, which allows to accurately model and calculate local flux values along with other intrinsic variables of great influence on the process, like the temperature polarization coefficient (TPC). The proposed model is based on energy and mass conservation principles and analogy between thermal and electrical systems. Experimental data was collected to validated the steady-state and dynamic responses of the model. The obtained results shows great agreement with the experimental data. The paper discusses the results of several simulations under various conditions to optimize the DCMD process efficiency and analyze its response. This demonstrates some potential applications of the proposed model to carry out scale up and design studies. © 2016

A lumped parameter core dynamics model for MTR type research reactors under natural convection regime

International Nuclear Information System (INIS)

Ardaneh, Kazem; Zaferanlouei, Salman

2013-01-01

Highlights: ► A model is presented to simulate the reactivity insertion transient in MTR reactors. ► Transient dynamics of IAEA 10 MW MTR type research reactor are evaluated. ► Maximum unprotected reactivity insertion for safe condition is calculated. ► The model predictions are validated with corresponding results in the literature. - Abstract: On the basis of lumped parameter modeling of both the kinetic and thermal–hydraulic effects, a reasonably accurate simplified model has been developed to predict the dynamic response of MTR reactors following to an unprotected reactivity insertion under natural convection regime. By this model the reactor transient behavior at a given initial steady-state can be solved by a set of ordinary differential equations. The model predictions have an acceptable consent with corresponding results of reactivity insertion transients analyzed in the literature. The inherent safety characteristics of MTR research reactors utilizing natural convection is clearly demonstrated by the expanded model. The safety margin of reactor operating is selected ONB condition and thereby the proposed model determines that any slight increase in the value of $0.73 for inserted reactivity will cause the maximum cladding surface temperature to exceed the ONB condition

Improved lumped models for transient combined convective and radiative cooling of a two-layer spherical fuel element

International Nuclear Information System (INIS)

Silva, Alice Cunha da; Su, Jian

2013-01-01

The High Temperature Gas cooled Reactor (HTGR) is a fourth generation thermal nuclear reactor, graphite-moderated and helium cooled. The HTGRs have important characteristics making essential the study of these reactors, as well as its fuel element. Examples of these are: high thermal efficiency,low operating costs and construction, passive safety attributes that allow implication of the respective plants. The Pebble Bed Modular Reactor (PBMR) is a HTGR with spherical fuel elements that named the reactor. This fuel element is composed by a particulate region with spherical inclusions, the fuel UO2 particles, dispersed in a graphite matrix and a convective heat transfer by Helium happens on the outer surface of the fuel element. In this work, the transient heat conduction in a spherical fuel element of a pebble-bed high temperature reactor was studied in a transient situation of combined convective and radiative cooling. Improved lumped parameter model was developed for the transient heat conduction in the two-layer composite sphere subjected to combined convective and radiative cooling. The improved lumped model was obtained through two-point Hermite approximations for integrals. Transient combined convective and radiative cooling of the two-layer spherical fuel element was analyzed to illustrate the applicability of the proposed lumped model, with respect to die rent values of the Biot number, the radiation-conduction parameter, the dimensionless thermal contact resistance, the dimensionless inner diameter and coating thickness, and the dimensionless thermal conductivity. It was shown by comparison with numerical solution of the original distributed parameter model that the improved lumped model, with H2,1/H1,1/H0,0 approximation yielded significant improvement of average temperature prediction over the classical lumped model. (author)

A Temperature Dependent Lumped-charge Model for Trench FS-IGBT

DEFF Research Database (Denmark)

Duan, Yaoqiang; Kang, Yong; Iannuzzo, Francesco

2018-01-01

Abstract: This paper proposes a temperature dependent lumped-charge model for FS-IGBT. Due to the evolution of the IGBT structure, the existing lumped-charge IGBT model established for NPT-IGBT is not suitable for the simulation of FS-IGBT. This paper extends the lumped-charge IGBT model including...... the field-stop (FS) structure and temperature characteristics. The temperature characteristics of the model are considered for both the bipolar part and unipolar part. In addition, a new PN junction model which can distinguish the collector structure is presented and validated by TCAD simulation. Finally...

A Calibrated Lumped Element Model for the Prediction of PSJ Actuator Efficiency Performance

Directory of Open Access Journals (Sweden)

Matteo Chiatto

2018-03-01

Full Text Available Among the various active flow control techniques, Plasma Synthetic Jet (PSJ actuators, or Sparkjets, represent a very promising technology, especially because of their high velocities and short response times. A practical tool, employed for design and manufacturing purposes, consists of the definition of a low-order model, lumped element model (LEM, which is able to predict the dynamic response of the actuator in a relatively quick way and with reasonable fidelity and accuracy. After a brief description of an innovative lumped model, this work faces the experimental investigation of a home-designed and manufactured PSJ actuator, for different frequencies and energy discharges. Particular attention has been taken in the power supply system design. A specific home-made Pitot tube has allowed the detection of velocity profiles along the jet radial direction, for various energy discharges, as well as the tuning of the lumped model with experimental data, where the total device efficiency has been assumed as a fitting parameter. The best fitting value not only contains information on the actual device efficiency, but includes some modeling and experimental uncertainties, related also to the used measurement technique.

Lumped hydrological models is an Occam' razor for runoff modeling in large Russian Arctic basins

OpenAIRE

Ayzel Georgy

2018-01-01

This study is aimed to investigate the possibility of three lumped hydrological models to predict daily runoff of large-scale Arctic basins for the modern period (1979-2014) in the case of substantial data scarcity. All models were driven only by meteorological forcing reanalysis dataset without any additional information about landscape, soil or vegetation cover properties of studied basins. We found limitations of model parameters calibration in ungauged basins using global optimization alg...

GEYSER/TONUS: a coupled multi-D lumped parameter code for reactor thermal hydraulics analysis in case of severe accidents

Energy Technology Data Exchange (ETDEWEB)

Petit, M.; Durin, M.; Gauvain, J.

1995-12-31

The safety requirements for future light water reactors include accounting for severe accidents in the design process. The design must now include mitigation features to limit pressure and temperature inside the building. Hydrogen concentration is also a major issue for severe accidents. Modelling the thermal hydraulics inside the containment requires the description of complex phenomena such as condensation, stratification, transport of gases and aerosols, heat transfers. The effect of mitigation systems will increase the heterogeneities in the building, and most of those phenomena can be coupled. The GEYSER/TONUS multi-dimensional computer code is under development at CEA Saclay to model this complex situation. It allow the coupling of parts of the containment described in a lumped parameter manner, together with meshed parts. Emphasis is put on the numerical methods used to solve the transient problem, and physical models of classical lumped parameters codes will be adapted for the spatially described zones. The code is developed in the environment of the CASTEM 2000/TRIO EF system which allows to construct sophisticated applications based upon it. (J.S.). 22 refs., 1 fig.

GEYSER/TONUS: a coupled multi-D lumped parameter code for reactor thermal hydraulics analysis in case of severe accidents

International Nuclear Information System (INIS)

Petit, M.; Durin, M.; Gauvain, J.

1995-01-01

The safety requirements for future light water reactors include accounting for severe accidents in the design process. The design must now include mitigation features to limit pressure and temperature inside the building. Hydrogen concentration is also a major issue for severe accidents. Modelling the thermal hydraulics inside the containment requires the description of complex phenomena such as condensation, stratification, transport of gases and aerosols, heat transfers. The effect of mitigation systems will increase the heterogeneities in the building, and most of those phenomena can be coupled. The GEYSER/TONUS multi-dimensional computer code is under development at CEA Saclay to model this complex situation. It allow the coupling of parts of the containment described in a lumped parameter manner, together with meshed parts. Emphasis is put on the numerical methods used to solve the transient problem, and physical models of classical lumped parameters codes will be adapted for the spatially described zones. The code is developed in the environment of the CASTEM 2000/TRIO EF system which allows to construct sophisticated applications based upon it. (J.S.). 22 refs., 1 fig

A lumped model for rotational modes in periodic solid composites

KAUST Repository

Peng, Pai; Asiri, Sharefa M.; Zhang, Xiujuan; Li, Yan; Wu, Ying

2013-01-01

We present a lumped model to study the rotational modes in a type of two-dimensional periodic solid composites comprised of a square array of rubber-coated steel cylinders embedded in an epoxy matrix. The model captures the physical essence of rotational modes in such systems for various combinations of material parameters, and, therefore it is able to describe the transition behaviour when the system is gradually adjusted from an elastic metamaterial to an elastic phononic crystal. From the model, we can define a transition zone which separates the typical elastic metamaterials and the phononic crystals.

A lumped model for rotational modes in periodic solid composites

KAUST Repository

Peng, Pai

2013-10-01

We present a lumped model to study the rotational modes in a type of two-dimensional periodic solid composites comprised of a square array of rubber-coated steel cylinders embedded in an epoxy matrix. The model captures the physical essence of rotational modes in such systems for various combinations of material parameters, and, therefore it is able to describe the transition behaviour when the system is gradually adjusted from an elastic metamaterial to an elastic phononic crystal. From the model, we can define a transition zone which separates the typical elastic metamaterials and the phononic crystals.

Simulation of nonlinear dynamics of a PWR core by an improved lumped formulation for fuel heat transfer

International Nuclear Information System (INIS)

Su, Jian; Cotta, Renato M.

2000-01-01

In this work, thermohydraulic behaviour of PWR, during reactivity insertion and partial loss-of-flow, is simulated by using a simplified mathematical model of reactor core and primary coolant. An improved lumped parameter formulation for transient heat conduction in fuel rod is used for core heat transfer modelling. Transient temperature response of fuel, cladding and coolant is analysed. (author)

Parameter identification in a nonlinear nuclear reactor model using quasilinearization

International Nuclear Information System (INIS)

Barreto, J.M.; Martins Neto, A.F.; Tanomaru, N.

1980-09-01

Parameter identification in a nonlinear, lumped parameter, nuclear reactor model is carried out using discrete output power measurements during the transient caused by an external reactivity change. In order to minimize the difference between the model and the reactor power responses, the parameter promt neutron generation time and a parameter in fuel temperature reactivity coefficient equation are adjusted using quasilinearization. The influences of the external reactivity disturbance, the number and frequency of measurements and the measurement noise level on the method accuracy and rate of convergence are analysed through simulation. Procedures for the design of the identification experiments are suggested. The method proved to be very effective for low level noise measurements. (Author) [pt

lumpR 2.0.0: an R package facilitating landscape discretisation for hillslope-based hydrological models

Science.gov (United States)

Pilz, Tobias; Francke, Till; Bronstert, Axel

2017-08-01

The characteristics of a landscape pose essential factors for hydrological processes. Therefore, an adequate representation of the landscape of a catchment in hydrological models is vital. However, many of such models exist differing, amongst others, in spatial concept and discretisation. The latter constitutes an essential pre-processing step, for which many different algorithms along with numerous software implementations exist. In that context, existing solutions are often model specific, commercial, or depend on commercial back-end software, and allow only a limited or no workflow automation at all. Consequently, a new package for the scientific software and scripting environment R, called lumpR, was developed. lumpR employs an algorithm for hillslope-based landscape discretisation directed to large-scale application via a hierarchical multi-scale approach. The package addresses existing limitations as it is free and open source, easily extendible to other hydrological models, and the workflow can be fully automated. Moreover, it is user-friendly as the direct coupling to a GIS allows for immediate visual inspection and manual adjustment. Sufficient control is furthermore retained via parameter specification and the option to include expert knowledge. Conversely, completely automatic operation also allows for extensive analysis of aspects related to landscape discretisation. In a case study, the application of the package is presented. A sensitivity analysis of the most important discretisation parameters demonstrates its efficient workflow automation. Considering multiple streamflow metrics, the employed model proved reasonably robust to the discretisation parameters. However, parameters determining the sizes of subbasins and hillslopes proved to be more important than the others, including the number of representative hillslopes, the number of attributes employed for the lumping algorithm, and the number of sub-discretisations of the representative hillslopes.

Comparing sensitivity analysis methods to advance lumped watershed model identification and evaluation

Directory of Open Access Journals (Sweden)

Y. Tang

2007-01-01

Full Text Available This study seeks to identify sensitivity tools that will advance our understanding of lumped hydrologic models for the purposes of model improvement, calibration efficiency and improved measurement schemes. Four sensitivity analysis methods were tested: (1 local analysis using parameter estimation software (PEST, (2 regional sensitivity analysis (RSA, (3 analysis of variance (ANOVA, and (4 Sobol's method. The methods' relative efficiencies and effectiveness have been analyzed and compared. These four sensitivity methods were applied to the lumped Sacramento soil moisture accounting model (SAC-SMA coupled with SNOW-17. Results from this study characterize model sensitivities for two medium sized watersheds within the Juniata River Basin in Pennsylvania, USA. Comparative results for the 4 sensitivity methods are presented for a 3-year time series with 1 h, 6 h, and 24 h time intervals. The results of this study show that model parameter sensitivities are heavily impacted by the choice of analysis method as well as the model time interval. Differences between the two adjacent watersheds also suggest strong influences of local physical characteristics on the sensitivity methods' results. This study also contributes a comprehensive assessment of the repeatability, robustness, efficiency, and ease-of-implementation of the four sensitivity methods. Overall ANOVA and Sobol's method were shown to be superior to RSA and PEST. Relative to one another, ANOVA has reduced computational requirements and Sobol's method yielded more robust sensitivity rankings.

Effects of non-LTE multiplet dynamics on lumped-state modelling in moderate to high atomic number plasmas

International Nuclear Information System (INIS)

Whitney, K G; Dasgupta, A; Davis, J; Coverdale, C A

2007-01-01

Two atomic models of the population dynamics of substates within the n 4 and n = 3 multiplets of nickel-like tungsten and beryllium-like iron, respectively, are described in this paper. The flexible atomic code (FAC) is used to calculate the collisional and radiative couplings and energy levels of the excited states within these ionization stages. These atomic models are then placed within larger principal-quantum-number-based ionization dynamic models of both tungsten and iron plasmas. Collisional-radiative equilibrium calculations are then carried out using these models that demonstrate how the multiplet substates depart from local thermodynamic equilibrium (LTE) as a function of ion density. The effect of these deviations from LTE on the radiative and collisional deexcitation rates of lumped 3s, 3p, 3d, 4s, 4p, 4d and 4f states is then calculated and least-squares fits to the density dependence of these lumped-state rate coefficients are obtained. The calculations show that, with the use of lumped-state models (which are in common use), one can accurately model the L- and M-shell ionization dynamics occurring in present-day Z-pinch experiments only through the addition of these extra, non-LTE-induced, rate coefficient density dependences. However, the derivation and use of low-order polynomial fits to these density dependences makes lumped-state modelling both viable and of value for post-processing analyses

Using a lumped conceptual hydrological model for five different catchments in Sweden

OpenAIRE

Ekenberg, Madeleine

2016-01-01

Hydrological models offer powerful tools for understanding and predicting. In this thesis we havereviewed the advantages and disadvantages of physically based distributed hydrological models andconceptually lumped hydrological models. Based on that review, we went into depth and developed aMATLAB code to test if a simple conceptual lumped hydrological model, namely GR2M, wouldperform satisfactory for five different catchments in different parts of Sweden. The model had ratherunsatisfactory re...

Lumped versus distributed thermoregulatory control: results from a three-dimensional dynamic model.

Science.gov (United States)

Werner, J; Buse, M; Foegen, A

1989-01-01

In this study we use a three-dimensional model of the human thermal system, the spatial grid of which is 0.5 ... 1.0 cm. The model is based on well-known physical heat-transfer equations, and all parameters of the passive system have definite physical values. According to the number of substantially different areas and organs, 54 spatially different values are attributed to each physical parameter. Compatibility of simulation and experiment was achieved solely on the basis of physical considerations and physiological basic data. The equations were solved using a modification of the alternating direction implicit method. On the basis of this complex description of the passive system close to reality, various lumped and distributed parameter control equations were tested for control of metabolic heat production, blood flow and sweat production. The simplest control equations delivering results on closed-loop control compatible with experimental evidence were determined. It was concluded that it is essential to take into account the spatial distribution of heat production, blood flow and sweat production, and that at least for control of shivering, distributed controller gains different from the pattern of distribution of muscle tissue are required. For sweat production this is not so obvious, so that for simulation of sweating control after homogeneous heat load a lumped parameter control may be justified. Based on these conclusions three-dimensional temperature profiles for cold and heat load and the dynamics for changes of the environmental conditions were computed. In view of the exact simulation of the passive system and the compatibility with experimentally attainable variables there is good evidence that those values extrapolated by the simulation are adequately determined. The model may be used both for further analysis of the real thermoregulatory mechanisms and for special applications in environmental and clinical health care.

A Hybrid Lumped Parameters/Finite Element/Boundary Element Model to Predict the Vibroacoustic Characteristics of an Axial Piston Pump

Directory of Open Access Journals (Sweden)

Shaogan Ye

2017-01-01

Full Text Available Low noise axial piston pumps become the rapid increasing demand in modern hydraulic fluid power systems. This paper proposes a systematic approach to simulate the vibroacoustic characteristics of an axial piston pump using a hybrid lumped parameters/finite element/boundary element (LP/FE/BE model, and large amount of experimental work was performed to validate the model. The LP model was developed to calculate the excitation forces and was validated by a comparison of outlet flow ripples. The FE model was developed to calculate the vibration of the pump, in which the modeling of main friction pairs using different spring elements was presented in detail, and the FE model was validated using experimental modal analysis and measured vibrations. The BE model was used to calculate the noise emitted from the pump, and a measurement of sound pressure level at representative field points in a hemianechoic chamber was conducted to validate the BE model. Comparisons between the simulated and measured results show that the developed LP/FE/BE model is effective in capturing the vibroacoustic characteristics of the pump. The presented approach can be extended to other types of fluid power components and contributes to the development of quieter fluid power systems.

Application of Biologically-Based Lumping To Investigate the ...

Science.gov (United States)

People are often exposed to complex mixtures of environmental chemicals such as gasoline, tobacco smoke, water contaminants, or food additives. However, investigators have often considered complex mixtures as one lumped entity. Valuable information can be obtained from these experiments, though this simplification provides little insight into the impact of a mixture's chemical composition on toxicologically-relevant metabolic interactions that may occur among its constituents. We developed an approach that applies chemical lumping methods to complex mixtures, in this case gasoline, based on biologically relevant parameters used in physiologically-based pharmacokinetic (PBPK) modeling. Inhalation exposures were performed with rats to evaluate performance of our PBPK model. There were 109 chemicals identified and quantified in the vapor in the chamber. The time-course kinetic profiles of 10 target chemicals were also determined from blood samples collected during and following the in vivo experiments. A general PBPK model was used to compare the experimental data to the simulated values of blood concentration for the 10 target chemicals with various numbers of lumps, iteratively increasing from 0 to 99. Large reductions in simulation error were gained by incorporating enzymatic chemical interactions, in comparison to simulating the individual chemicals separately. The error was further reduced by lumping the 99 non-target chemicals. Application of this biologic

Use of Ventricular Assist Device in Univentricular Physiology: The Role of Lumped Parameter Models.

Science.gov (United States)

Di Molfetta, Arianna; Ferrari, Gianfranco; Filippelli, Sergio; Fresiello, Libera; Iacobelli, Roberta; Gagliardi, Maria G; Amodeo, Antonio

2016-05-01

Failing single-ventricle (SV) patients might benefit from ventricular assist devices (VADs) as a bridge to heart transplantation. Considering the complex physiopathology of SV patients and the lack of established experience, the aim of this work was to realize and test a lumped parameter model of the cardiovascular system, able to simulate SV hemodynamics and VAD implantation effects. Data of 30 SV patients (10 Norwood, 10 Glenn, and 10 Fontan) were retrospectively collected and used to simulate patients' baseline. Then, the effects of VAD implantation were simulated. Additionally, both the effects of ventricular assistance and cavopulmonary assistance were simulated in different pathologic conditions on Fontan patients, including systolic dysfunction, diastolic dysfunction, and pulmonary vascular resistance increment. The model can reproduce patients' baseline well. Simulation results suggest that the implantation of VAD: (i) increases the cardiac output (CO) in all the three palliation conditions (Norwood 77.2%, Glenn 38.6%, and Fontan 17.2%); (ii) decreases the SV external work (SVEW) (Norwood 55%, Glenn 35.6%, and Fontan 41%); (iii) increases the mean pulmonary arterial pressure (Pap) (Norwood 39.7%, Glenn 12.1%, and Fontan 3%). In Fontan circulation, with systolic dysfunction, the left VAD (LVAD) increases CO (35%), while the right VAD (RVAD) determines a decrement of inferior vena cava pressure (Pvci) (39%) with 34% increment of CO. With diastolic dysfunction, the LVAD increases CO (42%) and the RVAD decreases the Pvci. With pulmonary vascular resistance increment, the RVAD allows the highest CO (50%) increment with the highest decrement of Pvci (53%). The single ventricular external work (SVEW) increases (decreases) increasing the VAD speed in cavopulmonary (ventricular) assistance. Numeric models could be helpful in this challenging and innovative field to support patients and VAD selection to optimize the clinical outcome and personalize the therapy

Uncertainty quantification in flux balance analysis of spatially lumped and distributed models of neuron-astrocyte metabolism.

Science.gov (United States)

Calvetti, Daniela; Cheng, Yougan; Somersalo, Erkki

2016-12-01

Identifying feasible steady state solutions of a brain energy metabolism model is an inverse problem that allows infinitely many solutions. The characterization of the non-uniqueness, or the uncertainty quantification of the flux balance analysis, is tantamount to identifying the degrees of freedom of the solution. The degrees of freedom of multi-compartment mathematical models for energy metabolism of a neuron-astrocyte complex may offer a key to understand the different ways in which the energetic needs of the brain are met. In this paper we study the uncertainty in the solution, using techniques of linear algebra to identify the degrees of freedom in a lumped model, and Markov chain Monte Carlo methods in its extension to a spatially distributed case. The interpretation of the degrees of freedom in metabolic terms, more specifically, glucose and oxygen partitioning, is then leveraged to derive constraints on the free parameters to guarantee that the model is energetically feasible. We demonstrate how the model can be used to estimate the stoichiometric energy needs of the cells as well as the household energy based on the measured oxidative cerebral metabolic rate of glucose and glutamate cycling. Moreover, our analysis shows that in the lumped model the net direction of lactate dehydrogenase (LDH) in the cells can be deduced from the glucose partitioning between the compartments. The extension of the lumped model to a spatially distributed multi-compartment setting that includes diffusion fluxes from capillary to tissue increases the number of degrees of freedom, requiring the use of statistical sampling techniques. The analysis of the distributed model reveals that some of the conclusions valid for the spatially lumped model, e.g., concerning the LDH activity and glucose partitioning, may no longer hold.

Lump solutions to the Kadomtsev–Petviashvili equation

Energy Technology Data Exchange (ETDEWEB)

Ma, Wen-Xiu, E-mail: mawx@cas.usf.edu

2015-09-25

Through symbolic computation with Maple, a class of lump solutions, rationally localized in all directions in the space, to the (2 + 1)-dimensional Kadomtsev–Petviashvili (KP) equation is presented, making use of its Hirota bilinear form. The resulting lump solutions contain six free parameters, two of which are due to the translation invariance of the KP equation and the other four of which satisfy a non-zero determinant condition guaranteeing analyticity and rational localization of the solutions. Three contour plots with different determinant values are sequentially made to show that the corresponding lump solution tends to zero when the determinant approaches zero. Two particular lump solutions with specific values of the involved parameters are plotted, as illustrative examples. - Highlights: • Positive quadratic function solutions. • Solitons rationally-localized in all directions in the space. • Solving systems of nonlinear algebraic equations by symbolic computation with Maple.

Estimation of time to rupture in a fire using 6FIRE, a lumped parameter UF6 cylinder transient heat transfer/stress analysis model

International Nuclear Information System (INIS)

Williams, W.R.; Anderson, J.C.

1995-01-01

The transportation of UF 6 is subject to regulations requiring the evaluation of packaging under a sequence of hypothetical accident conditions including exposure to a 30-min 800 degree C (1475 degree F) fire [10 CFR 71.73(c)(3)]. An issue of continuing interest is whether bare cylinders can withstand such a fire without rupturing. To address this issue, a lumped parameter heat transfer/stress analysis model (6FIRE) has been developed to simulate heating to the point of rupture of a cylinder containing UF 6 when it is exposed to a fire. The model is described, then estimates of time to rupture are presented for various cylinder types, fire temperatures, and fill conditions. An assessment of the quantity of UF 6 released from containment after rupture is also presented. Further documentation of the model is referenced

GEYSER/TONUS: A coupled multi-D lumped parameter code for reactor thermal hydraulics analysis in case of severe accidents

Energy Technology Data Exchange (ETDEWEB)

Petit, M.; Durin, M.; Gauvain, J. [Commissariat a l`Energie Atomique, Gif sur Yvette (France)

1995-09-01

In many countries, the safety requirements for future light water reactors include accounting for severe accidents in the design process. As far as the containment is concerned, the design must now include mitigation features to limit the pressure and temperature inside the building. Hydrogen concentration is also a major issue for severe accidents. In this context, new needs appear for the modeling of the thermal hydraulics inside the containment. It requires the description of complex phenomena such as condensation, stratification, transport of gases and aerosols, heat transfers. Moreover, the effect of mitigation systems will increase the heterogeneities in the building, and most of those phenomena can be coupled, as for example hydrogen stratification and condensation. To model such a complex situation, the use of multi-dimensional computer codes seems to be necessary in case of large volumes. The aim of the GEYSER/TONUS computer code is to fulfill this need. This code is currently under development at CEA in Saclay. It will allow the coupling of parts of the containment described in a lumped parameter manner, together with meshed parts. Emphasis is put on the numerical methods used to solve the transient problem, as the objective is to be able to treat complete scenarios. Physical models of classical lumped parameters codes will adapted for the spatially described zones. The code is developed in the environment of the CASTEM 2000/TRIO EF system which allows, thanks to its modular conception, to construct sophisticated applications based upon it.

Real-time simulation of response to load variation for a ship reactor based on point-reactor double regions and lumped parameter model

Energy Technology Data Exchange (ETDEWEB)

Wang Qiao; Zhang De [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China); Chen Wenzhen, E-mail: Cwz2@21cn.com [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China); Chen Zhiyun [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China)

2011-05-15

Research highlights: > We calculate the variation of main parameters of the reactor core by the Simulink. > The Simulink calculation software (SCS) can deal well with the stiff problem. > The high calculation precision is reached with less time, and the results can be easily displayed. > The quick calculation of ship reactor transient can be achieved by this method. - Abstract: Based on the point-reactor double regions and lumped parameter model, while the nuclear power plant second loop load is increased or decreased quickly, the Simulink calculation software (SCS) is adopted to calculate the variation of main physical and thermal-hydraulic parameters of the reactor core. The calculation results are compared with those of three-dimensional simulation program. It is indicated that the SCS can deal well with the stiff problem of the point-reactor kinetics equations and the coupled problem of neutronics and thermal-hydraulics. The high calculation precision can be reached with less time, and the quick calculation of parameters of response to load disturbance for the ship reactor can be achieved. The clear image of the calculation results can also be displayed quickly by the SCS, which is very significant and important to guarantee the reactor safety operation.

Impact of atrial fibrillation on the cardiovascular system through a lumped-parameter approach.

Science.gov (United States)

Scarsoglio, Stefania; Guala, Andrea; Camporeale, Carlo; Ridolfi, Luca

2014-11-01

Atrial fibrillation (AF) is the most common arrhythmia affecting millions of people in the Western countries and, due to the widespread impact on the population and its medical relevance, is largely investigated in both clinical and bioengineering sciences. However, some important feedback mechanisms are still not clearly established. The present study aims at understanding the global response of the cardiovascular system during paroxysmal AF through a lumped-parameter approach, which is here performed paying particular attention to the stochastic modeling of the irregular heartbeats and the reduced contractility of the heart. AF can be here analyzed by means of a wide number of hemodynamic parameters and avoiding the presence of other pathologies, which usually accompany AF. Reduced cardiac output with correlated drop of ejection fraction and decreased amount of energy converted to work by the heart during blood pumping, as well as higher left atrial volumes and pressures are some of the most representative results aligned with the existing clinical literature and here emerging during acute AF. The present modeling, providing new insights on cardiovascular variables which are difficult to measure and rarely reported in literature, turns out to be an efficient and powerful tool for a deeper comprehension and prediction of the arrythmia impact on the whole cardiovascular system.

Effect of nonlinear void reactivity on bifurcation characteristics of a lumped-parameter model of a BWR: A study relevant to RBMK

Energy Technology Data Exchange (ETDEWEB)

Verma, Dinkar, E-mail: dinkar@iitk.ac.in [Nuclear Engineering and Technology Program, Indian Institute of Technology Kanpur, Kanpur 208 016 (India); Kalra, Manjeet Singh, E-mail: drmanjeet.singh@dituniversity.edu.in [DIT University, Dehradun 248 009 (India); Wahi, Pankaj, E-mail: wahi@iitk.ac.in [Department of Mechanical Engineering, Indian Institute of Technology Kanpur, Kanpur 208 016 (India)

2017-04-15

Highlights: • A simplified model with nonlinear void reactivity feedback is studied. • Method of multiple scales for nonlinear analysis and oscillation characteristics. • Second order void reactivity dominates in determining system dynamics. • Opposing signs of linear and quadratic void reactivity enhances global safety. - Abstract: In the present work, the effect of nonlinear void reactivity on the dynamics of a simplified lumped-parameter model for a boiling water reactor (BWR) is investigated. A mathematical model of five differential equations comprising of neutronics and thermal-hydraulics encompassing the nonlinearities associated with both the reactivity feedbacks and the heat transfer process has been used. To this end, we have considered parameters relevant to RBMK for which the void reactivity is known to be nonlinear. A nonlinear analysis of the model exploiting the method of multiple time scales (MMTS) predicts the occurrence of the two types of Hopf bifurcation, namely subcritical and supercritical, leading to the evolution of limit cycles for a range of parameters. Numerical simulations have been performed to verify the analytical results obtained by MMTS. The study shows that the nonlinear reactivity has a significant influence on the system dynamics. A parametric study with varying nominal reactor power and operating conditions in coolant channel has also been performed which shows the effect of change in concerned parameter on the boundary between regions of sub- and super-critical Hopf bifurcations in the space constituted by the two coefficients of reactivities viz. the void and the Doppler coefficient of reactivities. In particular, we find that introduction of a negative quadratic term in the void reactivity feedback significantly increases the supercritical region and dominates in determining the system dynamics.

CFD analyses of steam and hydrogen distribution in a nuclear power plant

International Nuclear Information System (INIS)

Siccama, N.B.; Houkema, M.; Komen, E.M.J.

2003-01-01

A detailed three-dimensional Computational Fluid Dynamics (CFD) model of the containment of the nuclear power plant has been prepared in order to assess possible multidimensional phenomena. In a first code-to-code comparison step, the CFD model has been used to compute a reference accident scenario which has been analysed earlier with the lumped parameter code SPECTRA. The CFD results compare qualitatively well with the SPECTRA results. Subsequently, the actual steam jet from the primary system has been modelled in the CFD code in order to determine the hydrogen distribution for this realistically modelled source term. Based on the computed hydrogen distributions, it has been determined when use of lumped parameter codes is allowed and when use of CFD codes is required. (author)

Spatio-temporal modeling of nonlinear distributed parameter systems

CERN Document Server

Li, Han-Xiong

2011-01-01

The purpose of this volume is to provide a brief review of the previous work on model reduction and identifi cation of distributed parameter systems (DPS), and develop new spatio-temporal models and their relevant identifi cation approaches. In this book, a systematic overview and classifi cation on the modeling of DPS is presented fi rst, which includes model reduction, parameter estimation and system identifi cation. Next, a class of block-oriented nonlinear systems in traditional lumped parameter systems (LPS) is extended to DPS, which results in the spatio-temporal Wiener and Hammerstein s

Revisiting Appendicular Lump

Directory of Open Access Journals (Sweden)

R S Bhandari

2010-06-01

Full Text Available INTRODUCTION: Appendicular lump is a well known sequalae of acute appendicitis encountered in 2-6% of patients. Successful management of appendicular lump is controversial with different approaches. As many controversies are arising regarding management of appendicular lump. The aim of this study was to find out the outcome and evaluate possible need of changing our management strategy of appendicular lump. METHODS: A retrospective analysis of the patients managed with appendicular lump were done. All the patients admitted with diagnosis of appendicular lump and managed between, over two and half years, were included in the study. All age groups and both sex were included. Any patients whose diagnosis was changed after initial diagnosis of appendicular lump were excluded from the study. RESULTS: Total 75 patients had appendicular lump suggesting 10% incidence. Age varied between 11-83 years with nearly equal incidence in both sexes. Majority had onset of symptoms between 2 to 14 days with an average of 4 days. Average stay was 3 to 4 days. During study period, 12 (16% came with recurrence and 13 (17% cases came for elective appendectomy. CONCLUSIONS: Based on our finding, it is not sufficient to change our classical management strategy of appendicular lump and suggests a need for long term prospective study in this very common clinical condition. KEYWORDS: appendicular lump, conservative management.

A 3D Dynamic Lumped Parameter Thermal Network of Air-Cooled YASA Axial Flux Permanent Magnet Synchronous Machine

Directory of Open Access Journals (Sweden)

Abdalla Hussein Mohamed

2018-03-01

Full Text Available To find the temperature rise for high power density yokeless and segmented armature (YASA axial flux permanent magnet synchronous (AFPMSM machines quickly and accurately, a 3D lumped parameter thermal model is developed and validated experimentally and by finite element (FE simulations on a 4 kW YASA machine. Additionally, to get insight in the thermal transient response of the machine, the model accounts for the thermal capacitance of different machine components. The model considers the stator, bearing, and windage losses, as well as eddy current losses in the magnets on the rotors. The new contribution of this work is that the thermal model takes cooling via air channels between the magnets on the rotor discs into account. The model is parametrized with respect to the permanent magnet (PM angle ratio, the PM thickness ratio, the air gap length, and the rotor speed. The effect of the channels is incorporated via convection equations based on many computational fluid dynamics (CFD computations. The model accuracy is validated at different values of parameters by FE simulations in both transient and steady state. The model takes less than 1 s to solve for the temperature distribution.

Revisiting appendicular lump.

Science.gov (United States)

Bhandari, R S; Thakur, D K; Lakhey, P J; Singh, K P

2010-01-01

Appendicular lump is a well known sequalae of acute appendicitis encountered in 2-6% of patients. Successful management of appendicular lump is controversial with different approaches. As many controversies are arising regarding management of appendicular lump. The aim of this study was to find out the outcome and evaluate possible need of changing our management strategy of appendicular lump. A retrospective analysis of the patients managed with appendicular lump were done. All the patients admitted with diagnosis of appendicular lump and managed between, over two and half years, were included in the study. All age groups and both sex were included. Any patients whose diagnosis was changed after initial diagnosis of appendicular lump were excluded from the study. Total 75 patients had appendicular lump suggesting 10% incidence. Age varied between 11-83 years with nearly equal incidence in both sexes. Majority had onset of symptoms between 2 to 14 days with an average of 4 days. Average stay was 3 to 4 days. During study period, 12 (16%) came with recurrence and 13 (17%) cases came for elective appendectomy. Based on our finding, it is not sufficient to change our classical management strategy of appendicular lump and suggests a need for long term prospective study in this very common clinical condition.

Application of Biologically Based Lumping To Investigate the Toxicokinetic Interactions of a Complex Gasoline Mixture.

Science.gov (United States)

Jasper, Micah N; Martin, Sheppard A; Oshiro, Wendy M; Ford, Jermaine; Bushnell, Philip J; El-Masri, Hisham

2016-03-15

People are often exposed to complex mixtures of environmental chemicals such as gasoline, tobacco smoke, water contaminants, or food additives. We developed an approach that applies chemical lumping methods to complex mixtures, in this case gasoline, based on biologically relevant parameters used in physiologically based pharmacokinetic (PBPK) modeling. Inhalation exposures were performed with rats to evaluate the performance of our PBPK model and chemical lumping method. There were 109 chemicals identified and quantified in the vapor in the chamber. The time-course toxicokinetic profiles of 10 target chemicals were also determined from blood samples collected during and following the in vivo experiments. A general PBPK model was used to compare the experimental data to the simulated values of blood concentration for 10 target chemicals with various numbers of lumps, iteratively increasing from 0 to 99. Large reductions in simulation error were gained by incorporating enzymatic chemical interactions, in comparison to simulating the individual chemicals separately. The error was further reduced by lumping the 99 nontarget chemicals. The same biologically based lumping approach can be used to simplify any complex mixture with tens, hundreds, or thousands of constituents.

Regionalising Parameters of a Conceptual Rainfall-Runoff Model for ...

African Journals Online (AJOL)

IHACRES, a lumped conceptual rainfall-runoff model, was calibrated to six catchments ranging in size from 49km2 to 600 km2 within the upper Tana River basin to obtain a set of model parameters that characterise the hydrological behaviour within the region. Physical catchment attributes indexing topography, soil and ...

Comparison of the AWA lumped-circuit model of electrical discharges with empirical data

International Nuclear Information System (INIS)

Maier, W.B. II; Kadish, A.; Robiscoe, R.T.

1990-01-01

The authors compare experimental data for three 1.7-m-long transient discharges with an AWA lumped- circuit discharge model in which the arc resistance is taken from the Arc Welder's Ansatz, R a = V*/|I |, where V* is a positive constant and I is the discharge current. In addition to the arc resistance, there is a small series resistance R present in the external circuit. A single value for each of R and V* is deduced from the data, and these values are used to characterize all three discharges. Adequate agreement with the experimental data is obtained; for example, the authors predict the proper number of current reversals for each discharge and abrupt termination of current flow after a finite time. The authors suggest that the AWA lumped circuit provides a better representation of the data than a standard lumped-circuit RLC model and hence is more useful as a tool for prediction and interpretation of discharges

lumpGEM: Systematic generation of subnetworks and elementally balanced lumped reactions for the biosynthesis of target metabolites.

Directory of Open Access Journals (Sweden)

Meric Ataman

2017-07-01

Full Text Available In the post-genomic era, Genome-scale metabolic networks (GEMs have emerged as invaluable tools to understand metabolic capabilities of organisms. Different parts of these metabolic networks are defined as subsystems/pathways, which are sets of functional roles to implement a specific biological process or structural complex, such as glycolysis and TCA cycle. Subsystem/pathway definition is also employed to delineate the biosynthetic routes that produce biomass building blocks. In databases, such as MetaCyc and SEED, these representations are composed of linear routes from precursors to target biomass building blocks. However, this approach cannot capture the nested, complex nature of GEMs. Here we implemented an algorithm, lumpGEM, which generates biosynthetic subnetworks composed of reactions that can synthesize a target metabolite from a set of defined core precursor metabolites. lumpGEM captures balanced subnetworks, which account for the fate of all metabolites along the synthesis routes, thus encapsulating reactions from various subsystems/pathways to balance these metabolites in the metabolic network. Moreover, lumpGEM collapses these subnetworks into elementally balanced lumped reactions that specify the cost of all precursor metabolites and cofactors. It also generates alternative subnetworks and lumped reactions for the same metabolite, accounting for the flexibility of organisms. lumpGEM is applicable to any GEM and any target metabolite defined in the network. Lumped reactions generated by lumpGEM can be also used to generate properly balanced reduced core metabolic models.

On 4-degree-of-freedom biodynamic models of seated occupants: Lumped-parameter modeling

Science.gov (United States)

Bai, Xian-Xu; Xu, Shi-Xu; Cheng, Wei; Qian, Li-Jun

2017-08-01

It is useful to develop an effective biodynamic model of seated human occupants to help understand the human vibration exposure to transportation vehicle vibrations and to help design and improve the anti-vibration devices and/or test dummies. This study proposed and demonstrated a methodology for systematically identifying the best configuration or structure of a 4-degree-of-freedom (4DOF) human vibration model and for its parameter identification. First, an equivalent simplification expression for the models was made. Second, all of the possible 23 structural configurations of the models were identified. Third, each of them was calibrated using the frequency response functions recommended in a biodynamic standard. An improved version of non-dominated sorting genetic algorithm (NSGA-II) based on Pareto optimization principle was used to determine the model parameters. Finally, a model evaluation criterion proposed in this study was used to assess the models and to identify the best one, which was based on both the goodness of curve fits and comprehensive goodness of the fits. The identified top configurations were better than those reported in the literature. This methodology may also be extended and used to develop the models with other DOFs.

Valuing Ecosystem Services with Fishery Rents: A Lumped-Parameter Approach to Hypoxia in the Neuse River Estuary

Directory of Open Access Journals (Sweden)

Larry B. Crowder

2011-11-01

Full Text Available Valuing ecosystem services with microeconomic underpinnings presents challenges because these services typically constitute nonmarket values and contribute to human welfare indirectly through a series of ecological pathways that are dynamic, nonlinear, and difficult to quantify and link to appropriate economic spatial and temporal scales. This paper develops and demonstrates a method to value a portion of ecosystem services when a commercial fishery is dependent on the quality of estuarine habitat. Using a lumped-parameter, dynamic open access bioeconomic model that is spatially explicit and includes predator-prey interactions, this paper quantifies part of the value of improved ecosystem function in the Neuse River Estuary when nutrient pollution is reduced. Specifically, it traces the effects of nitrogen loading on the North Carolina commercial blue crab fishery by modeling the response of primary production and the subsequent impact on hypoxia (low dissolved oxygen. Hypoxia, in turn, affects blue crabs and their preferred prey. The discounted present value fishery rent increase from a 30% reduction in nitrogen loadings in the Neuse is $2.56 million, though this welfare estimate is fairly sensitive to some parameter values. Surprisingly, this number is not sensitive to initial conditions.

Hydrogen-combustion analyses of large-scale tests

International Nuclear Information System (INIS)

Gido, R.G.; Koestel, A.

1986-01-01

This report uses results of the large-scale tests with turbulence performed by the Electric Power Research Institute at the Nevada Test Site to evaluate hydrogen burn-analysis procedures based on lumped-parameter codes like COMPARE-H2 and associated burn-parameter models. The test results: (1) confirmed, in a general way, the procedures for application to pulsed burning, (2) increased significantly our understanding of the burn phenomenon by demonstrating that continuous burning can occur, and (3) indicated that steam can terminate continuous burning. Future actions recommended include: (1) modification of the code to perform continuous-burn analyses, which is demonstrated, (2) analyses to determine the type of burning (pulsed or continuous) that will exist in nuclear containments and the stable location if the burning is continuous, and (3) changes to the models for estimating burn parameters

Hydrogen-combustion analyses of large-scale tests

International Nuclear Information System (INIS)

Gido, R.G.; Koestel, A.

1986-01-01

This report uses results of the large-scale tests with turbulence performed by the Electric Power Research Institute at the Nevada Test Site to evaluate hydrogen burn-analysis procedures based on lumped-parameter codes like COMPARE-H2 and associated burn-parameter models. The test results (a) confirmed, in a general way, the procedures for application to pulsed burning, (b) increased significantly our understanding of the burn phenomenon by demonstrating that continuous burning can occur and (c) indicated that steam can terminate continuous burning. Future actions recommended include (a) modification of the code to perform continuous-burn analyses, which is demonstrated, (b) analyses to determine the type of burning (pulsed or continuous) that will exist in nuclear containments and the stable location if the burning is continuous, and (c) changes to the models for estimating burn parameters

A simplified lumped model for the optimization of post-buckled beam architecture wideband generator

Science.gov (United States)

Liu, Weiqun; Formosa, Fabien; Badel, Adrien; Hu, Guangdi

2017-11-01

Buckled beams structures are a classical kind of bistable energy harvesters which attract more and more interests because of their capability to scavenge energy over a large frequency band in comparison with linear generator. The usual modeling approach uses the Galerkin mode discretization method with relatively high complexity, while the simplification with a single-mode solution lacks accuracy. It stems on the optimization of the energy potential features to finally define the physical and geometrical parameters. Therefore, in this paper, a simple lumped model is proposed with explicit relationship between the potential shape and parameters to allow efficient design of bistable beams based generator. The accuracy of the approximation model is studied with the effectiveness of application analyzed. Moreover, an important fact, that the bending stiffness has little influence on the potential shape with low buckling level and the sectional area determined, is found. This feature extends the applicable range of the model by utilizing the design of high moment of inertia. Numerical investigations demonstrate that the proposed model is a simple and reliable tool for design. An optimization example of using the proposed model is demonstrated with satisfactory performance.

Lump solutions with interaction phenomena in the (2+1)-dimensional Ito equation

Science.gov (United States)

Zou, Li; Yu, Zong-Bing; Tian, Shou-Fu; Feng, Lian-Li; Li, Jin

2018-03-01

In this paper, we consider the (2+1)-dimensional Ito equation, which was introduced by Ito. By considering the Hirota’s bilinear method, and using the positive quadratic function, we obtain some lump solutions of the Ito equation. In order to ensure rational localization and analyticity of these lump solutions, some sufficient and necessary conditions are provided on the parameters that appeared in the solutions. Furthermore, the interaction solutions between lump solutions and the stripe solitons are discussed by combining positive quadratic function with exponential function. Finally, the dynamic properties of these solutions are shown via the way of graphical analysis by selecting appropriate values of the parameters.

The influence of model parameters on catchment-response

International Nuclear Information System (INIS)

Shah, S.M.S.; Gabriel, H.F.; Khan, A.A.

2002-01-01

This paper deals with the study of influence of influence of conceptual rainfall-runoff model parameters on catchment response (runoff). A conceptual modified watershed yield model is employed to study the effects of model-parameters on catchment-response, i.e. runoff. The model is calibrated, using manual parameter-fitting approach, also known as trial and error parameter-fitting. In all, there are twenty one (21) parameters that control the functioning of the model. A lumped parametric approach is used. The detailed analysis was performed on Ling River near Kahuta, having catchment area of 56 sq. miles. The model includes physical parameters like GWSM, PETS, PGWRO, etc. fitting coefficients like CINF, CGWS, etc. and initial estimates of the surface-water and groundwater storages i.e. srosp and gwsp. Sensitivity analysis offers a good way, without repetititious computations, the proper weight and consideration that must be taken when each of the influencing factor is evaluated. Sensitivity-analysis was performed to evaluate the influence of model-parameters on runoff. The sensitivity and relative contributions of model parameters influencing catchment-response are studied. (author)

Lumped model for rotational modes in phononic crystals

KAUST Repository

Peng, Pai

2012-10-16

We present a lumped model for the rotational modes induced by the rotational motion of individual scatterers in two-dimensional phononic crystals comprised of square arrays of solid cylindrical scatterers in solid hosts. The model provides a physical interpretation of the origin of the rotational modes, reveals the important role played by the rotational motion in determining the band structure, and reproduces the dispersion relations in a certain range. The model increases the possibilities of manipulating wave propagation in phononic crystals. In particular, expressions derived from the model for eigenfrequencies at high symmetry points unambiguously predict the presence of a new type of Dirac-like cone at the Brillouin center, which is found to be the result of accidental degeneracy of the rotational and dipolar modes.

Lumped model for rotational modes in phononic crystals

KAUST Repository

Peng, Pai; Mei, Jun; Wu, Ying

2012-01-01

We present a lumped model for the rotational modes induced by the rotational motion of individual scatterers in two-dimensional phononic crystals comprised of square arrays of solid cylindrical scatterers in solid hosts. The model provides a physical interpretation of the origin of the rotational modes, reveals the important role played by the rotational motion in determining the band structure, and reproduces the dispersion relations in a certain range. The model increases the possibilities of manipulating wave propagation in phononic crystals. In particular, expressions derived from the model for eigenfrequencies at high symmetry points unambiguously predict the presence of a new type of Dirac-like cone at the Brillouin center, which is found to be the result of accidental degeneracy of the rotational and dipolar modes.

New Procedure to Develop Lumped Kinetic Models for Heavy Fuel Oil Combustion

KAUST Repository

Han, Yunqing; Elbaz, Ayman M.; Roberts, William L.; Im, Hong G.

2016-01-01

A new procedure to develop accurate lumped kinetic models for complex fuels is proposed, and applied to the experimental data of the heavy fuel oil measured by thermogravimetry. The new procedure is based on the pseudocomponents representing

distributed parameter model of spiral-wound sepralator for treatment of uranyl nitrate effluents

International Nuclear Information System (INIS)

El-Bialy, S.H; Elsherbiny, A.E.

2004-01-01

in this paper, mathematical formulation of spiral-wound sepralator was derived and applied for the treatment of effluent stream which is produced during nuclear fuel processing stage. the concentration of the stream has a value up to 200 ppm . cross-flow characteristic of both feed and permeate streams was taken into account and their mutual effects on the values of system variables were investigated. of course, such a flow pattern leads to a heterogeneous system which leads-in turn-to six partial differential equations, beside a set of algebraic equations. those were solved numerically and the results were used to estimate the average values of both permeate flux and percent solute rejection. then, these were compared with both experimental data in addition to the results of lumped parameter model. the study showed that distributed parameter model gives better results than lumped parameter one compared with experimental data

Lumped-Element Dynamic Electro-Thermal model of a superconducting magnet

Science.gov (United States)

Ravaioli, E.; Auchmann, B.; Maciejewski, M.; ten Kate, H. H. J.; Verweij, A. P.

2016-12-01

Modeling accurately electro-thermal transients occurring in a superconducting magnet is challenging. The behavior of the magnet is the result of complex phenomena occurring in distinct physical domains (electrical, magnetic and thermal) at very different spatial and time scales. Combined multi-domain effects significantly affect the dynamic behavior of the system and are to be taken into account in a coherent and consistent model. A new methodology for developing a Lumped-Element Dynamic Electro-Thermal (LEDET) model of a superconducting magnet is presented. This model includes non-linear dynamic effects such as the dependence of the magnet's differential self-inductance on the presence of inter-filament and inter-strand coupling currents in the conductor. These effects are usually not taken into account because superconducting magnets are primarily operated in stationary conditions. However, they often have significant impact on magnet performance, particularly when the magnet is subject to high ramp rates. Following the LEDET method, the complex interdependence between the electro-magnetic and thermal domains can be modeled with three sub-networks of lumped-elements, reproducing the electrical transient in the main magnet circuit, the thermal transient in the coil cross-section, and the electro-magnetic transient of the inter-filament and inter-strand coupling currents in the superconductor. The same simulation environment can simultaneously model macroscopic electrical transients and phenomena at the level of superconducting strands. The model developed is a very useful tool for reproducing and predicting the performance of conventional quench protection systems based on energy extraction and quench heaters, and of the innovative CLIQ protection system as well.

Causes of breast lumps (image)

Science.gov (United States)

... breast lumps are benign (non-cancerous), as in fibroadenoma, a condition that mostly affects women under age ... with the menstrual cycle, whereas a lump from fibroadenoma does not. While most breast lumps are benign, ...

Scattering of massless lumps and non-local charges in the two-dimensional classical non-linear sigma-model

International Nuclear Information System (INIS)

Luescher, M.; Pohlmeyer, K.

1977-09-01

Finite energy solutions of the field equations of the non-linear sigma-model are shown to decay asymptotically into massless lumps. By means of a linear eigenvalue problem connected with the field equations we then find an infinite set of dynamical conserved charges. They, however, do not provide sufficient information to decode the complicated scattering of lumps. (orig.) [de

Dark lump excitations in superfluid Fermi gases

Science.gov (United States)

Xu, Yan-Xia; Duan, Wen-Shan

2012-11-01

We study the linear and nonlinear properties of two-dimensional matter-wave pulses in disk-shaped superfluid Fermi gases. A Kadomtsev—Petviashvili I (KPI) solitary wave has been realized for superfluid Fermi gases in the limited cases of Bardeen—Cooper—Schrieffer (BCS) regime, Bose—Einstein condensate (BEC) regime, and unitarity regime. One-lump solution as well as one-line soliton solutions for the KPI equation are obtained, and two-line soliton solutions with the same amplitude are also studied in the limited cases. The dependence of the lump propagating velocity and the sound speed of two-dimensional superfluid Fermi gases on the interaction parameter are investigated for the limited cases of BEC and unitarity.

Dark lump excitations in superfluid Fermi gases

International Nuclear Information System (INIS)

Xu Yan-Xia; Duan Wen-Shan

2012-01-01

We study the linear and nonlinear properties of two-dimensional matter-wave pulses in disk-shaped superfluid Fermi gases. A Kadomtsev—Petviashvili I (KPI) solitary wave has been realized for superfluid Fermi gases in the limited cases of Bardeen—Cooper—Schrieffer (BCS) regime, Bose—Einstein condensate (BEC) regime, and unitarity regime. One-lump solution as well as one-line soliton solutions for the KPI equation are obtained, and two-line soliton solutions with the same amplitude are also studied in the limited cases. The dependence of the lump propagating velocity and the sound speed of two-dimensional superfluid Fermi gases on the interaction parameter are investigated for the limited cases of BEC and unitarity

A new lumped-parameter approach to simulating flow processes in unsaturated dual-porosity media

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, R.W.; Hadgu, T.; Bodvarsson, G.S. [Lawrence Berkeley Laboratory, CA (United States)

1995-03-01

We have developed a new lumped-parameter dual-porosity approach to simulating unsaturated flow processes in fractured rocks. Fluid flow between the fracture network and the matrix blocks is described by a nonlinear equation that relates the imbibition rate to the local difference in liquid-phase pressure between the fractures and the matrix blocks. This equation is a generalization of the Warren-Root equation, but unlike the Warren-Root equation, is accurate in both the early and late time regimes. The fracture/matrix interflow equation has been incorporated into a computational module, compatible with the TOUGH simulator, to serve as a source/sink term for fracture elements. The new approach achieves accuracy comparable to simulations in which the matrix blocks are discretized, but typically requires an order of magnitude less computational time.

Improving the temporal transposability of lumped hydrological models on twenty diversified U.S. watersheds

Directory of Open Access Journals (Sweden)

G. Seiller

2015-03-01

Full Text Available Study region: Twenty diversified U.S. watersheds. Study focus: Identifying optimal parameter sets for hydrological modeling on a specific catchment remains an important challenge for numerous applied and research projects. This is particularly the case when working under contrasted climate conditions that question the temporal transposability of the parameters. Methodologies exist, mainly based on Differential Split Sample Tests, to examine this concern. This work assesses the improved temporal transposability of a multimodel implementation, based on twenty dissimilar lumped conceptual structures and on twenty U.S. watersheds, over the performance of the individual models. New hydrological insights for the region: Individual and collective temporal transposabilities are analyzed and compared on the twenty studied watersheds. Results show that individual models performances on contrasted climate conditions are very dissimilar depending on test period and watershed, without the possibility to identify a best solution in all circumstances. They also confirm that performance and robustness are clearly enhanced using an ensemble of rainfall-runoff models instead of individual ones. The use of (calibrated weight averaged multimodels further improves temporal transposability over simple averaged ensemble, in most instances, confirming added-value of this approach but also the need to evaluate how individual models compensate each other errors. Keywords: Rainfall-runoff modeling, Multimodel approach, Differential Split Sample Test, Deterministic combination, Outputs averaging

airGRteaching: an R-package designed for teaching hydrology with lumped hydrological models

Science.gov (United States)

Thirel, Guillaume; Delaigue, Olivier; Coron, Laurent; Andréassian, Vazken; Brigode, Pierre

2017-04-01

Lumped hydrological models are useful and convenient tools for research, engineering and educational purposes. They propose catchment-scale representations of the precipitation-discharge relationship. Thanks to their limited data requirements, they can be easily implemented and run. With such models, it is possible to simulate a number of hydrological key processes over the catchment with limited structural and parametric complexity, typically evapotranspiration, runoff, underground losses, etc. The Hydrology Group at Irstea (Antony) has been developing a suite of rainfall-runoff models over the past 30 years. This resulted in a suite of models running at different time steps (from hourly to annual) applicable for various issues including water balance estimation, forecasting, simulation of impacts and scenario testing. Recently, Irstea has developed an easy-to-use R-package (R Core Team, 2016), called airGR (Coron et al., 2016, 2017), to make these models widely available. Although its initial target public was hydrological modellers, the package is already used for educational purposes. Indeed, simple models allow for rapidly visualising the effects of parameterizations and model components on flows hydrographs. In order to avoid the difficulties that students may have when manipulating R and datasets, we developed (Delaigue and Coron, 2016): - Three simplified functions to prepare data, calibrate a model and run a simulation - Simplified and dynamic plot functions - A shiny (Chang et al., 2016) interface that connects this R-package to a browser-based visualisation tool. On this interface, the students can use different hydrological models (including the possibility to use a snow-accounting model), manually modify their parameters and automatically calibrate their parameters with diverse objective functions. One of the visualisation tabs of the interface includes observed precipitation and temperature, simulated snowpack (if any), observed and simulated

Drop-on-Demand Inkjet Printhead Performance Enhancement by Dynamic Lumped Element Modeling for Printable Electronics Fabrication

Directory of Open Access Journals (Sweden)

Maowei He

2014-01-01

Full Text Available The major challenge in printable electronics fabrication is the print resolution and accuracy. In this paper, the dynamic lumped element model (DLEM is proposed to directly simulate an inkjet-printed nanosilver droplet formation process and used for predictively controlling jetting characteristics. The static lumped element model (LEM previously developed by the authors is extended to dynamic model with time-varying equivalent circuits to characterize nonlinear behaviors of piezoelectric printhead. The model is then used to investigate how performance of the piezoelectric ceramic actuator influences jetting characteristics of nanosilver ink. Finally, the proposed DLEM is applied to predict the printing quality using nanosilver ink. Experimental results show that, compared to other analytic models, the proposed DLEM has a simpler structure with the sufficient simulation and prediction accuracy.

A lumped parameter method of characteristics approach and multigroup kernels applied to the subgroup self-shielding calculation in MPACT

International Nuclear Information System (INIS)

Stimpson, Shane G.; Liu, Yuxuan; Collins, Benjamin S.; Clarno, Kevin T.

2017-01-01

An essential component of the neutron transport solver is the resonance self-shielding calculation used to determine equivalence cross sections. The neutron transport code, MPACT, is currently using the subgroup self-shielding method, in which the method of characteristics (MOC) is used to solve purely absorbing fixed-source problems. Recent efforts incorporating multigroup kernels to the MOC solvers in MPACT have reduced runtime by roughly 2×. Applying the same concepts for self-shielding and developing a novel lumped parameter approach to MOC, substantial improvements have also been made to the self-shielding computational efficiency without sacrificing any accuracy. These new multigroup and lumped parameter capabilities have been demonstrated on two test cases: (1) a single lattice with quarter symmetry known as VERA (Virtual Environment for Reactor Applications) Progression Problem 2a and (2) a two-dimensional quarter-core slice known as Problem 5a-2D. From these cases, self-shielding computational time was reduced by roughly 3–4×, with a corresponding 15–20% increase in overall memory burden. An azimuthal angle sensitivity study also shows that only half as many angles are needed, yielding an additional speedup of 2×. In total, the improvements yield roughly a 7–8× speedup. Furthermore given these performance benefits, these approaches have been adopted as the default in MPACT.

A lumped parameter method of characteristics approach and multigroup kernels applied to the subgroup self-shielding calculation in MPACT

Directory of Open Access Journals (Sweden)

Shane Stimpson

2017-09-01

Full Text Available An essential component of the neutron transport solver is the resonance self-shielding calculation used to determine equivalence cross sections. The neutron transport code, MPACT, is currently using the subgroup self-shielding method, in which the method of characteristics (MOC is used to solve purely absorbing fixed-source problems. Recent efforts incorporating multigroup kernels to the MOC solvers in MPACT have reduced runtime by roughly 2×. Applying the same concepts for self-shielding and developing a novel lumped parameter approach to MOC, substantial improvements have also been made to the self-shielding computational efficiency without sacrificing any accuracy. These new multigroup and lumped parameter capabilities have been demonstrated on two test cases: (1 a single lattice with quarter symmetry known as VERA (Virtual Environment for Reactor Applications Progression Problem 2a and (2 a two-dimensional quarter-core slice known as Problem 5a-2D. From these cases, self-shielding computational time was reduced by roughly 3–4×, with a corresponding 15–20% increase in overall memory burden. An azimuthal angle sensitivity study also shows that only half as many angles are needed, yielding an additional speedup of 2×. In total, the improvements yield roughly a 7–8× speedup. Given these performance benefits, these approaches have been adopted as the default in MPACT.

Decay of Kadomtsev-Petviashvili lumps in dissipative media

Science.gov (United States)

Clarke, S.; Gorshkov, K.; Grimshaw, R.; Stepanyants, Y.

2018-03-01

The decay of Kadomtsev-Petviashvili lumps is considered for a few typical dissipations-Rayleigh dissipation, Reynolds dissipation, Landau damping, Chezy bottom friction, viscous dissipation in the laminar boundary layer, and radiative losses caused by large-scale dispersion. It is shown that the straight-line motion of lumps is unstable under the influence of dissipation. The lump trajectories are calculated for two most typical models of dissipation-the Rayleigh and Reynolds dissipations. A comparison of analytical results obtained within the framework of asymptotic theory with the direct numerical calculations of the Kadomtsev-Petviashvili equation is presented. Good agreement between the theoretical and numerical results is obtained.

Assessment of Lumped-Parameter Models for Rigid Footings

DEFF Research Database (Denmark)

Andersen, Lars

2010-01-01

and vertical translations as well as torsion and rocking, and the necessity of coupling between horizontal sliding and rocking is discussed. Most of the analyses are carried out for hexagonal footings; but in order to generalise the conclusions to a broader variety of footings, comparisons are made...

Characterization of an air jet haptic lump display.

Science.gov (United States)

Bianchi, Matteo; Gwilliam, James C; Degirmenci, Alperen; Okamura, Allison M

2011-01-01

During manual palpation, clinicians rely on distributed tactile information to identify and localize hard lumps embedded in soft tissue. The development of tactile feedback systems to enhance palpation using robot-assisted minimally invasive surgery (RMIS) systems is challenging due to size and weight constraints, motivating a pneumatic actuation strategy. Recently, an air jet approach has been proposed for generating a lump percept. We use this technique to direct a thin stream of air through an aperture directly on the finger pad, which indents the skin in a hemispherical manner, producing a compelling lump percept. We hypothesize that the perceived parameters of the lump (e.g. size and stiffness) can be controlled by jointly adjusting air pressure and the aperture size through which air escapes. In this work, we investigate how these control variables interact to affect perceived pressure on the finger pad. First, we used a capacitive tactile sensor array to measure the effect of aperture size on output pressure, and found that peak output pressure increases with aperture size. Second, we performed a psychophysical experiment for each aperture size to determine the just noticeable difference (JND) of air pressure on the finger pad. Subject-averaged pressure JND values ranged from 19.4-24.7 kPa, with no statistical differences observed between aperture sizes. The aperture-pressure relationship and the pressure JND values will be fundamental for future display control.

A Lumped Thermal Model Including Thermal Coupling and Thermal Boundary Conditions for High Power IGBT Modules

DEFF Research Database (Denmark)

Bahman, Amir Sajjad; Ma, Ke; Blaabjerg, Frede

2018-01-01

Detailed thermal dynamics of high power IGBT modules are important information for the reliability analysis and thermal design of power electronic systems. However, the existing thermal models have their limits to correctly predict these complicated thermal behavior in the IGBTs: The typically used...... thermal model based on one-dimensional RC lumps have limits to provide temperature distributions inside the device, moreover some variable factors in the real-field applications like the cooling and heating conditions of the converter cannot be adapted. On the other hand, the more advanced three......-dimensional thermal models based on Finite Element Method (FEM) need massive computations, which make the long-term thermal dynamics difficult to calculate. In this paper, a new lumped three-dimensional thermal model is proposed, which can be easily characterized from FEM simulations and can acquire the critical...

Application of Mass Lumped Higher Order Finite Elements

International Nuclear Information System (INIS)

J. Chen, H.R. Strauss, S.C. Jardin, W. Park, L.E. Sugiyama, G. Fu, J. Breslau

2005-01-01

There are many interesting phenomena in extended-MHD such as anisotropic transport, mhd, 2-fluid effects stellarator and hot particles. Any one of them challenges numerical analysts, and researchers are seeking for higher order methods, such as higher order finite difference, higher order finite elements and hp/spectral elements. It is true that these methods give more accurate solution than their linear counterparts. However, numerically they are prohibitively expensive. Here we give a successful solution of this conflict by applying mass lumped higher order finite elements. This type of elements not only keep second/third order accuracy but also scale closely to linear elements by doing mass lumping. This is especially true for second order lump elements. Full M3D and anisotropic transport models are studied

New Procedure to Develop Lumped Kinetic Models for Heavy Fuel Oil Combustion

KAUST Repository

Han, Yunqing

2016-09-20

A new procedure to develop accurate lumped kinetic models for complex fuels is proposed, and applied to the experimental data of the heavy fuel oil measured by thermogravimetry. The new procedure is based on the pseudocomponents representing different reaction stages, which are determined by a systematic optimization process to ensure that the separation of different reaction stages with highest accuracy. The procedure is implemented and the model prediction was compared against that from a conventional method, yielding a significantly improved agreement with the experimental data. © 2016 American Chemical Society.

Lumped Mass Modeling for Local-Mode-Suppressed Element Connectivity

DEFF Research Database (Denmark)

Joung, Young Soo; Yoon, Gil Ho; Kim, Yoon Young

2005-01-01

connectivity parameterization (ECP) is employed. On the way to the ultimate crashworthy structure optimization, we are now developing a local mode-free topology optimization formulation that can be implemented in the ECP method. In fact, the local mode-freeing strategy developed here can be also used directly...... experiencing large structural changes, appears to be still poor. In ECP, the nodes of the domain-discretizing elements are connected by zero-length one-dimensional elastic links having varying stiffness. For computational efficiency, every elastic link is now assumed to have two lumped masses at its ends....... Choosing appropriate penalization functions for lumped mass and link stiffness is important for local mode-free results. However, unless the objective and constraint functions are carefully selected, it is difficult to obtain clear black-and-white results. It is shown that the present formulation is also...

Assessing aquifer vulnerability from lumped parameter modeling of modern water proportions in groundwater mixtures - Application to nitrate pollution in California's South Coast Range

Science.gov (United States)

Hagedorn, B.; Ruane, M.; Clark, N.

2017-12-01

In California, the overuse of synthetic fertilizers and manure in agriculture have caused nitrate (NO3) to be one of the state's most widespread groundwater pollutants. Given that nitrogen fertilizer applications have steadily increased since the 1950s and given that soil percolation and recharge transit times in California can exceed timescales of decades, the nitrate impact on groundwater resources is likely a legacy for years and even decades to come. This study presents a methodology for groundwater vulnerability assessment that operates independently of difficult-to-constrain soil and aquifer property data (i.e., saturated thickness, texture, porosity, conductivity, etc.), but rather utilizes groundwater age and, more importantly, groundwater mixing information to illustrate actual vulnerability at the water table. To accomplish this, the modern (i.e., less than 60-year old) water proportion (MWP) in groundwater mixtures is computed via lumped parameter modeling of chemical tracer (i.e., 3H, 14C and 3Hetrit) data. These MWPs are then linked to groundwater dissolved oxygen (DO) values to describe the risk for soil zone-derived nitrate to accumulate in the saturated zone. Preliminary studies carried out for 71 wells in California's South Coast Range-Coastal (SCRC) study unit reveal MWP values derived from binary dispersion models of 3.24% to 21.8%. The fact that high MWPs generally coincide with oxic (DO ≥1.5 mg/L) groundwater conditions underscores the risk towards increased groundwater NO3 pollution for many of the tested wells. These results support the conclusion that best agricultural management and policy objectives should incorporate groundwater vulnerability models that are developed at the same spatial scale as the decision making.

Comparison of Lumped and Distributed Hydrologic Models Used for Planning and Water Resources Management at the Combeima River Basin, Colombia.

Science.gov (United States)

Salgado, F., II; Vélez, J.

2014-12-01

The catchment area is considered as the planning unit of natural resources where multiple factors as biotic, abiotic and human interact in a web of relationships making this unit a complex system. It is also considered by several authors as the most suitable unit for studying the water movement in nature and a tool for the understanding of natural processes. This research implements several hydrological models commonly used in water resources management and planning. It is the case of Témez, abcd, T, P, ARMA (1,1), and the lumped conceptual model TETIS. This latest model has been implemented in its distributed version for comparison purposes and it has been the basis for obtaining information, either through the reconstruction of natural flow series, filling missing data, forecasting or simulation. Hydrological models make use of lumped data of precipitation and potential evapotranspiration, as well as the following parameters for each one of the models which are related to soil properties as capillary storage capacity; the hydraulic saturated conductivity of the upper and lower layers of the soil, and residence times in the flow surface, subsurface layers and base flow. The calibration and the validation process of the models were performed making adjustments to the parameters listed above, taking into account the consistency in the efficiency indexes and the adjustment between the observed and simulated flows using the flow duration curve. The Nash index gave good results for the TETIS model and acceptable values were obtained to the other models. The calibration of the distributed model was complex and its results were similar to those obtained with the aggregated model. This comparison allows planners to use the hydrological multimodel techniques to reduce the uncertainty associated with planning processes in developing countries. Moreover, taking into account the information limitations required to implement a hydrological models, this application can be a

Advertising Pricing Models in Media Markets: Lump-Sum versus Per-Consumer Charges

OpenAIRE

Helmut Dietl; Markus Lang; Panlang Lin

2012-01-01

This paper develops a model of asymmetric competition between a pay and a free media platform. The pay media platform generates revenues from media consumers through subscription fees, while the free media platform generates revenues from charging advertisers either on a lump-sum basis (regime A) or on a per-consumer basis (regime B). We show that the free platform produces a higher advertising level and attracts more consumers in regime A than B although advertisers must pay more for ads and...

Seismic response analyses for reactor facilities at Savannah River

International Nuclear Information System (INIS)

Miller, C.A.; Costantino, C.J.; Xu, J.

1991-01-01

The reactor facilities at the Savannah River Plant (SRP) were designed during the 1950's. The original seismic criteria defining the input ground motion was 0.1 G with UBC [uniform building code] provisions used to evaluate structural seismic loads. Later ground motion criteria have defined the free field seismic motion with a 0.2 G ZPA [free field acceleration] and various spectral shapes. The spectral shapes have included the Housner spectra, a site specific spectra, and the US NRC [Nuclear Regulatory Commission] Reg. Guide 1.60 shape. The development of these free field seismic criteria are discussed in the paper. The more recent seismic analyses have been of the following type: fixed base response spectra, frequency independent lumped parameter soil/structure interaction (SSI), frequency dependent lumped parameter SSI, and current state of the art analyses using computer codes such as SASSI. The results from these computations consist of structural loads and floor response spectra (used for piping and equipment qualification). These results are compared in the paper and the methods used to validate the results are discussed. 14 refs., 11 figs

A distributed parameter model of transmission line transformer for high voltage nanosecond pulse generation.

Science.gov (United States)

Li, Jiangtao; Zhao, Zheng; Li, Longjie; He, Jiaxin; Li, Chenjie; Wang, Yifeng; Su, Can

2017-09-01

A transmission line transformer has potential advantages for nanosecond pulse generation including excellent frequency response and no leakage inductance. The wave propagation process in a secondary mode line is indispensable due to an obvious inside transient electromagnetic transition in this scenario. The equivalent model of the transmission line transformer is crucial for predicting the output waveform and evaluating the effects of magnetic cores on output performance. However, traditional lumped parameter models are not sufficient for nanosecond pulse generation due to the natural neglect of wave propagations in secondary mode lines based on a lumped parameter assumption. In this paper, a distributed parameter model of transmission line transformer was established to investigate wave propagation in the secondary mode line and its influential factors through theoretical analysis and experimental verification. The wave propagation discontinuity in the secondary mode line induced by magnetic cores is emphasized. Characteristics of the magnetic core under a nanosecond pulse were obtained by experiments. Distribution and formation of the secondary mode current were determined for revealing essential wave propagation processes in secondary mode lines. The output waveform and efficiency were found to be affected dramatically by wave propagation discontinuity in secondary mode lines induced by magnetic cores. The proposed distributed parameter model was proved more suitable for nanosecond pulse generation in aspects of secondary mode current, output efficiency, and output waveform. In depth, comprehension of underlying mechanisms and a broader view of the working principle of the transmission line transformer for nanosecond pulse generation can be obtained through this research.

Cytomorphological study of palpable breast lumps

Directory of Open Access Journals (Sweden)

PK Choudhary

2015-09-01

Full Text Available Background: Breast lump is a very common clinical presentation for which fine needle aspiration cytology is often sought for. Because of it’s significant diagnositic value, FNAC has become a routine tool in the evaluation of the nature of the lesion. The objective of this study was to determine the cytomorphological patterns of breast lump in eastern part of Nepal among individuals attending Nobel Medical College. Materials and Methods: This was a retrospective descriptive study done in department of pathology from December 2012 to June 2015. All individuals presenting with breast lumps was included in this study. FNAC was done as per standard procedure and categorized as per United Kingdom National Health Survey Breast Screening Programme (UK-NHS-BSP categories and further also categorized in to neoplastic and non-neolastic categories. Results: We studied 771 cases of breast lumps. Occurrence of breast lump was more common in female (97.4%. Neoplastic lesions accounted for 84.1% of cases out of which benign comprised of 94.6% and malignant comprised of 5.6%. Common benign lesions observed were that of fibroadenona (264 and fibrocystic changes (204. Ductal carcinoma was the most common malignant lesions. All malignant lesions were observed in older age and female sex population.Conclusion: Most of the cases of breast lumps are benign in nature and very few accounted for malignant cases. There is predominance of benign lesions in young age and increased malignancy in older age and female population. 

Inverse analyses of effective diffusion parameters relevant for a two-phase moisture model of cementitious materials

DEFF Research Database (Denmark)

Addassi, Mouadh; Johannesson, Björn; Wadsö, Lars

2018-01-01

Here we present an inverse analyses approach to determining the two-phase moisture transport properties relevant to concrete durability modeling. The purposed moisture transport model was based on a continuum approach with two truly separate equations for the liquid and gas phase being connected...... test, and, (iv) capillary suction test. Mass change over time, as obtained from the drying test, the two different cup test intervals and the capillary suction test, was used to obtain the effective diffusion parameters using the proposed inverse analyses approach. The moisture properties obtained...

Novo modelo de parâmetros concentrados aplicado à hidratação de grãos New model of lumped parameters applied to grain hydration

Directory of Open Access Journals (Sweden)

Mônica Ronobo Coutinho

2007-09-01

Full Text Available Este trabalho apresenta um novo modelo fenomenológico de parâmetros concentrados para a hidratação de grãos de soja, obtido a partir de um balanço de massa em regime transiente nos grãos, admitindo duas hipóteses básicas: 1º variação do volume do grão diretamente proporcional à variação da sua massa ao longo da hidratação; e 2º variação exponencial do coeficiente de transferência de massa aparente em função da concentração de água na soja. Este modelo possui apenas dois parâmetros, os quais foram estimados a partir do ajuste deste às medidas da umidade do grão ao longo do tempo, avaliadas em várias temperaturas. Os resultados revelam que o modelo proposto é adequado, enquanto o coeficiente de transferência de massa aparente depende da temperatura e apresenta variações significativas ao longo da hidratação.A new first principle model with lumped parameters was developed for the hydration of soya beans. A transient mass balance was applied to the soya beans taking into consideration two basic hypotheses:1º variation of the volume directly proportional to the variation of the mass of the grain during the process, 2º Exponential variation of the apparent coefficient of mass transfer in function of water concentration in the soy. This model has got just two parameters, which were evaluated from adjustment of model to the measures of grain moisture along the time, at several temperatures. The results indicate that the proposed model was able to represent the hydration process, while the mass transfer coefficient depends on the temperature and it presents significant variations along the hydration.

Intermittent reservoir daily-inflow prediction using lumped and ...

Indian Academy of Sciences (India)

For the present case study considered, both MLR and ARIMA models performed ... is to be remembered that the transformation of ... Multi-linear regression; lumped and distributed data; time-series models; cause-effect ... flow data are short for adequate system study. ..... that the standard deviation, skewness, kurtosis.

Rational Solutions and Lump Solutions of the Potential YTSF Equation

Science.gov (United States)

Sun, Hong-Qian; Chen, Ai-Hua

2017-07-01

By using of the bilinear form, rational solutions and lump solutions of the potential Yu-Toda-Sasa-Fukuyama (YTSF) equation are derived. Dynamics of the fundamental lump solution, n1-order lump solutions, and N-lump solutions are studied for some special cases. We also find some interaction behaviours of solitary waves and one lump of rational solutions.

New lumped-mass-stick model based on modal characteristics of structures: development and application to a nuclear containment building

Science.gov (United States)

Roh, Hwasung; Lee, Huseok; Lee, Jong Seh

2013-06-01

In this study, a new lumped-mass-stick model (LMSM) is developed based on the modal characteristics of a structure such as eigenvalues and eigenvectors. The simplified model, named the "frequency adaptive lumped-massstick model," hasonly a small number of stick elements and nodes to provide the same natural frequencies of the structure and is applied to a nuclear containment building. To investigate the numerical performance of the LMSM, a time history analysis is carried out on both the LMSM and the finite element model (FEM) for a nuclear containment building. A comparison of the results shows that the dynamic responses of the LMSM in terms of displacement and acceleration are almost identical to those of the FEM. In addition, the results in terms of fl oor response spectra at certain elevations are also in good agreement.

7 CFR 1726.205 - Multiparty lump sum quotations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Multiparty lump sum quotations. 1726.205 Section 1726....205 Multiparty lump sum quotations. The borrower or its engineer must contact a sufficient number of... basis of written lump sum quotations, the borrower will select the supplier or contractor based on the...

Rogue waves and lump solutions for a (3+1)-dimensional generalized B-type Kadomtsev-Petviashvili equation in fluid mechanics

Science.gov (United States)

Wu, Xiao-Yu; Tian, Bo; Chai, Han-Peng; Sun, Yan

2017-08-01

Under investigation in this letter is a (3+1)-dimensional generalized B-type Kadomtsev-Petviashvili equation, which describes the weakly dispersive waves propagating in a fluid. Employing the Hirota method and symbolic computation, we obtain the lump, breather-wave and rogue-wave solutions under certain constraints. We graphically study the lump waves with the influence of the parameters h1, h3 and h5 which are all the real constants: When h1 increases, amplitude of the lump wave increases, and location of the peak moves; when h3 increases, lump wave’s amplitude decreases, but location of the peak keeps unchanged; when h5 changes, lump wave’s peak location moves, but amplitude keeps unchanged. Breather waves and rogue waves are displayed: Rogue waves emerge when the periods of the breather waves go to the infinity.

Lumped impulses, discrete displacements and a moving load analysis

NARCIS (Netherlands)

Kok, A.W.M.

1997-01-01

Finite element models are usually presented as relations between lumped forces and discrete displacements. Mostly finite element models are found by the elaboration of the method of the virtual work - which is a special case of the Galerkin's variational principle -. By application of Galerkin's

Lithium-ion Battery Electrothermal Model, Parameter Estimation, and Simulation Environment

Directory of Open Access Journals (Sweden)

Simone Orcioni

2017-03-01

Full Text Available The market for lithium-ion batteries is growing exponentially. The performance of battery cells is growing due to improving production technology, but market request is growing even more rapidly. Modeling and characterization of single cells and an efficient simulation environment is fundamental for the development of an efficient battery management system. The present work is devoted to defining a novel lumped electrothermal circuit of a single battery cell, the extraction procedure of the parameters of the single cell from experiments, and a simulation environment in SystemC-WMS for the simulation of a battery pack. The electrothermal model of the cell was validated against experimental measurements obtained in a climatic chamber. The model is then used to simulate a 48-cell battery, allowing statistical variations among parameters. The different behaviors of the cells in terms of state of charge, current, voltage, or heat flow rate can be observed in the results of the simulation environment.

Using lumped modelling for providing simple metrics and associated uncertainties of catchment response to agricultural-derived nitrates pollutions

Science.gov (United States)

RUIZ, L.; Fovet, O.; Faucheux, M.; Molenat, J.; Sekhar, M.; Aquilina, L.; Gascuel-odoux, C.

2013-12-01

The development of simple and easily accessible metrics is required for characterizing and comparing catchment response to external forcings (climate or anthropogenic) and for managing water resources. The hydrological and geochemical signatures in the stream represent the integration of the various processes controlling this response. The complexity of these signatures over several time scales from sub-daily to several decades [Kirchner et al., 2001] makes their deconvolution very difficult. A large range of modeling approaches intent to represent this complexity by accounting for the spatial and/or temporal variability of the processes involved. However, simple metrics are not easily retrieved from these approaches, mostly because of over-parametrization issues. We hypothesize that to obtain relevant metrics, we need to use models that are able to simulate the observed variability of river signatures at different time scales, while being as parsimonious as possible. The lumped model ETNA (modified from[Ruiz et al., 2002]) is able to simulate adequately the seasonal and inter-annual patterns of stream NO3 concentration. Shallow groundwater is represented by two linear stores with double porosity and riparian processes are represented by a constant nitrogen removal function. Our objective was to identify simple metrics of catchment response by calibrating this lumped model on two paired agricultural catchments where both N inputs and outputs were monitored for a period of 20 years. These catchments, belonging to ORE AgrHys, although underlain by the same granitic bedrock are displaying contrasted chemical signatures. The model was able to simulate the two contrasted observed patterns in stream and groundwater, both on hydrology and chemistry, and at the seasonal and pluri-annual scales. It was also compatible with the expected trends of nitrate concentration since 1960. The output variables of the model were used to compute the nitrate residence time in both the

Definition of datum of materials lump size on conveyors by means of reflected gamma-radiation method

International Nuclear Information System (INIS)

Gal'yanov, A.V.; Antonov, V.A.; Laptev, Yu.V.

2001-01-01

A method of technological control of large-size lumps in conveyor-transported crushed material based on intensity measurement of X-ray and gamma radiation reflected from the material surface was suggested. The method was substantiated theoretically and as a result it was shown that dispersion of radiation intensity, multiply measured for short periods of time, can be analytic parameter of large-size lumps yield. Principled methodical and design recommendations on the method practical applications are given [ru

Computationally Efficient Modelling of Dynamic Soil-Structure Interaction of Offshore Wind Turbines on Gravity Footings

DEFF Research Database (Denmark)

Damgaard, Mads; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

2014-01-01

of a 5.0 MW offshore wind turbine is evaluated for different stratifications, environmental conditions and foundation geometries by the aeroelastic nonlinear multi-body code HAWC2. Analyses show that a consistent lumped-parameter model with three to five internal degrees of freedom per displacement...

Optimal Component Lumping: problem formulation and solution techniques

DEFF Research Database (Denmark)

Lin, Bao; Leibovici, Claude F.; Jørgensen, Sten Bay

2008-01-01

This paper presents a systematic method for optimal lumping of a large number of components in order to minimize the loss of information. In principle, a rigorous composition-based model is preferable to describe a system accurately. However, computational intensity and numerical issues restrict ...

Determination of heat flows inside turbochargers by means of a one dimensional lumped model

OpenAIRE

Olmeda González, Pablo Cesar; Dolz Ruiz, Vicente; Arnau Martínez, Francisco José; Reyes Belmonte, Miguel Angel

2013-01-01

In the present paper, a methodology to calculate the heat fluxes inside a turbocharger from diesel passenger car is presented. The heat transfer phenomenon is solved by using a one dimensional lumped model that takes into account both the heat fluxes between the different turbocharger elements, as well as the heat fluxes between the working fluids and the turbocharger elements. This heat transfer study is supported by the high temperature differences between the working fluids passing thr...

Simplified distributed parameters BWR dynamic model for transient and stability analysis

International Nuclear Information System (INIS)

Espinosa-Paredes, Gilberto; Nunez-Carrera, Alejandro; Vazquez-Rodriguez, Alejandro

2006-01-01

This paper describes a simplified model to perform transient and linear stability analysis for a typical boiling water reactor (BWR). The simplified transient model was based in lumped and distributed parameters approximations, which includes vessel dome and the downcomer, recirculation loops, neutron process, fuel pin temperature distribution, lower and upper plenums reactor core and pressure and level controls. The stability was determined by studying the linearized versions of the equations representing the BWR system in the frequency domain. Numerical examples are used to illustrate the wide application of the simplified BWR model. We concluded that this simplified model describes properly the dynamic of a BWR and can be used for safety analysis or as a first approach in the design of an advanced BWR

Influences of lumped passes on welding residual stress of a thick-walled nuclear rotor steel pipe by multipass narrow gap welding

Energy Technology Data Exchange (ETDEWEB)

Tan, Long, E-mail: mse.longtan@gmail.com [State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Zhang, Jianxun; Zhuang, Dong [State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Liu, Chuan [Provincial Key Lab of Advanced Welding Technology, Jiangsu University of Science and Technology, Zhenjiang 212003 (China)

2014-07-01

Highlights: • The internal residual stress of the thick-walled pipe is measured by using the local removal blind hole method. • Two lumped-pass models are developed to reduce computational cost. • The effect of lumped passes on the welding residual stress is discussed. • Reasonable lumped-pass model can guarantee the accuracy and improve the computational efficiency. - Abstract: The purpose of this study is to investigate the effect of the lumped passes simulation on the distribution of residual stresses before and after heat treatment in a thick-walled nuclear power rotor pipe with a 89-pass narrow gap welding process. The local removal blind hole method was used to measure internal residual stress of the thick-walled pipe after post weld heat treatment (PWHT). Based on the ANSYS software, a two-dimensional axisymmetric finite element model is employed. Two lumped-pass models of M-5th model (five weld beads as one lumped pass) and M-10th model (ten weld beads as one lumped pass) were developed to reduce computational cost. Based on the results in this study, the distributions of residual stresses of a thick-walled welded pipe before and after PWHT are developed. Meanwhile, the distribution of the through-wall axial residual stress along the weld center line is demonstrated to be a self-equilibrating type. In addition, the investigation results show that reasonable and reliable lumped-pass model can not only guarantee the accuracy of the simulated results, but also improve the computational efficiency in the thermo-elastic–plastic FE analysis procedure. Therefore, from the viewpoint of engineering application the developed lumped-pass computational procedure is a promising and useful method to predict residual stress of large and complex welded structures.

Influences of lumped passes on welding residual stress of a thick-walled nuclear rotor steel pipe by multipass narrow gap welding

International Nuclear Information System (INIS)

Tan, Long; Zhang, Jianxun; Zhuang, Dong; Liu, Chuan

2014-01-01

Highlights: • The internal residual stress of the thick-walled pipe is measured by using the local removal blind hole method. • Two lumped-pass models are developed to reduce computational cost. • The effect of lumped passes on the welding residual stress is discussed. • Reasonable lumped-pass model can guarantee the accuracy and improve the computational efficiency. - Abstract: The purpose of this study is to investigate the effect of the lumped passes simulation on the distribution of residual stresses before and after heat treatment in a thick-walled nuclear power rotor pipe with a 89-pass narrow gap welding process. The local removal blind hole method was used to measure internal residual stress of the thick-walled pipe after post weld heat treatment (PWHT). Based on the ANSYS software, a two-dimensional axisymmetric finite element model is employed. Two lumped-pass models of M-5th model (five weld beads as one lumped pass) and M-10th model (ten weld beads as one lumped pass) were developed to reduce computational cost. Based on the results in this study, the distributions of residual stresses of a thick-walled welded pipe before and after PWHT are developed. Meanwhile, the distribution of the through-wall axial residual stress along the weld center line is demonstrated to be a self-equilibrating type. In addition, the investigation results show that reasonable and reliable lumped-pass model can not only guarantee the accuracy of the simulated results, but also improve the computational efficiency in the thermo-elastic–plastic FE analysis procedure. Therefore, from the viewpoint of engineering application the developed lumped-pass computational procedure is a promising and useful method to predict residual stress of large and complex welded structures

Best-estimate LOCA simulation in a PWR-W containment building with a detailed 3D GOTHIC model

International Nuclear Information System (INIS)

Jimenez, G.; Fernandez-Cosials, K.; Bocanegra, R.; Lopez-Alonso, E.

2015-01-01

The design-basis accidents in a PWR-W containment building are usually simulated with a lumped parameter model, normally used for license analysis. Nevertheless, some phenomenology is difficult to be simulated with a lumped model: the condensation rate in each structure, stagnant water areas, temperature in different compartments, sumps and recirculation pumps disabled because of lack of water, etc. Therefore, for the detailed study of the thermal-hydraulic (TH) behaviour in every room of the containment building could be more appropriate to do it with a detailed 3D representation of the containment building geometry. The main objective of this project has been to build a 3D PWR-W containment model with the GOTHIC code to analyze the detailed behavior during a design basis accident. In the process of the 3D GOTHIC model development some previous steps were necessary: a detailed CAD model of the containment, followed by a simplified model adapted to the GOTHIC geometric capabilities. Once the geometry has been adapted to the GOTHIC requirements, the 3D model is created with this information. A design-basis accident has been simulated with the 3D model (LBLOCA), and the local TH behaviour is analysed. The results show that in comparison with a lumped parameter model, high temperatures are reached locally. Nevertheless the average pressure behaviour is found to be similar to that given by a lumped parameter model. The present paper demonstrates that is possible to build a 3D PWR-W model with the GOTHIC code with enough resolution to analyse the TH behaviour in each one of the containment rooms but at the same time with reasonable computing time. Once the GOTHIC model has been created a new road is opened enabling the simulation of other accidents such as MSLB, a SBLOCA or even a long-term SBO sequence. This document is made up of an abstract and the slides of the presentation. (authors)

Analysis of stability and bifurcations of fixed points and periodic solutions of a lumped model of neocortex with two delays

NARCIS (Netherlands)

Visser, Sid; Meijer, Hil G.E.; van Putten, Michel J.A.M.; van Gils, Stephan A.

2012-01-01

A lumped model of neural activity in neocortex is studied to identify regions of multi-stability of both steady states and periodic solutions. Presence of both steady states and periodic solutions is considered to correspond with epileptogenesis. The model, which consists of two delay differential

Towards a lumped reaction model for future designer fuels

Energy Technology Data Exchange (ETDEWEB)

Vandersickel, A.; Wright, Y.M.; Boulouchos, K. [ETH Zurich, Aerothermochemistry and Combustion Systems Laboratory, Zurich (Switzerland). Inst. of Energy Technology

2009-07-01

The homogeneous charge compression ignition (HCCI) is one of the most promising engine processes to simultaneously reduce nitrogen oxide and soot emissions. However, its applicability is hindered by its relatively limited operating range. Designer fuels offer unique possibilities for tailoring evaporation and auto-ignition properties, offering a means to control and expand the HCCI operation range. The identification of HCCI relevant fuel properties as well as the definition of a new fuel index able to describe a fuels suitability for HCCI was required in order to develop such designer fuels. This paper discussed a numerical and experimental investigation of a large set of technical fuels covering a wide range of properties. The paper discussed mechanism development approaches, optimization of the lumped mechanism, and and results. Zheng's 7-step reaction mechanism was successfully coupled with a genetic optimization algorithm and fitted to n-heptane ignition delay data. It was concluded that the presented coupled approach could improve the predictive quality of the model and demonstrate that the Zheng model was sufficiently elaborate to emulate the influence of temperature, pressure, exhaust gas recirculation and lambda on ignition. 8 refs., 1 tab., 3 figs.

Towards a lumped reaction model for future designer fuels

International Nuclear Information System (INIS)

Vandersickel, A.; Wright, Y.M.; Boulouchos, K.

2009-01-01

The homogeneous charge compression ignition (HCCI) is one of the most promising engine processes to simultaneously reduce nitrogen oxide and soot emissions. However, its applicability is hindered by its relatively limited operating range. Designer fuels offer unique possibilities for tailoring evaporation and auto-ignition properties, offering a means to control and expand the HCCI operation range. The identification of HCCI relevant fuel properties as well as the definition of a new fuel index able to describe a fuels suitability for HCCI was required in order to develop such designer fuels. This paper discussed a numerical and experimental investigation of a large set of technical fuels covering a wide range of properties. The paper discussed mechanism development approaches, optimization of the lumped mechanism, and and results. Zheng's 7-step reaction mechanism was successfully coupled with a genetic optimization algorithm and fitted to n-heptane ignition delay data. It was concluded that the presented coupled approach could improve the predictive quality of the model and demonstrate that the Zheng model was sufficiently elaborate to emulate the influence of temperature, pressure, exhaust gas recirculation and lambda on ignition. 8 refs., 1 tab., 3 figs.

Single lump breast surface stress assessment study

Science.gov (United States)

Vairavan, R.; Ong, N. R.; Sauli, Z.; Kirtsaeng, S.; Sakuntasathien, S.; Paitong, P.; Alcain, J. B.; Lai, S. L.; Retnasamy, V.

2017-09-01

Breast cancer is one of the commonest cancers diagnosed among women around the world. Simulation approach has been utilized to study, characterize and improvise detection methods for breast cancer. However, minimal simulation work has been done to evaluate the surface stress of the breast with lumps. Thus, in this work, simulation analysis was utilized to evaluate and assess the breast surface stress due to the presence of a lump within the internal structure of the breast. The simulation was conducted using the Elmer software. Simulation results have confirmed that the presence of a lump within the breast causes stress on the skin surface of the breast.

Development of CAP code for nuclear power plant containment: Lumped model

Energy Technology Data Exchange (ETDEWEB)

Hong, Soon Joon, E-mail: sjhong90@fnctech.com [FNC Tech. Co. Ltd., Heungdeok 1 ro 13, Giheung-gu, Yongin-si, Gyeonggi-do 446-908 (Korea, Republic of); Choo, Yeon Joon; Hwang, Su Hyun; Lee, Byung Chul [FNC Tech. Co. Ltd., Heungdeok 1 ro 13, Giheung-gu, Yongin-si, Gyeonggi-do 446-908 (Korea, Republic of); Ha, Sang Jun [Central Research Institute, Korea Hydro & Nuclear Power Company, Ltd., 70, 1312-gil, Yuseong-daero, Yuseong-gu, Daejeon 305-343 (Korea, Republic of)

2015-09-15

Highlights: • State-of-art containment analysis code, CAP, has been developed. • CAP uses 3-field equations, water level oriented upwind scheme, local head model. • CAP has a function of linked calculation with reactor coolant system code. • CAP code assessments showed appropriate prediction capabilities. - Abstract: CAP (nuclear Containment Analysis Package) code has been developed in Korean nuclear society for the analysis of nuclear containment thermal hydraulic behaviors including pressure and temperature trends and hydrogen concentration. Lumped model of CAP code uses 2-phase, 3-field equations for fluid behaviors, and has appropriate constitutive equations, 1-dimensional heat conductor model, component models, trip and control models, and special process models. CAP can run in a standalone mode or a linked mode with a reactor coolant system analysis code. The linked mode enables the more realistic calculation of a containment response and is expected to be applicable to a more complicated advanced plant design calculation. CAP code assessments were carried out by gradual approaches: conceptual problems, fundamental phenomena, component and principal phenomena, experimental validation, and finally comparison with other code calculations on the base of important phenomena identifications. The assessments showed appropriate prediction capabilities of CAP.

Development of CAP code for nuclear power plant containment: Lumped model

International Nuclear Information System (INIS)

Hong, Soon Joon; Choo, Yeon Joon; Hwang, Su Hyun; Lee, Byung Chul; Ha, Sang Jun

2015-01-01

Highlights: • State-of-art containment analysis code, CAP, has been developed. • CAP uses 3-field equations, water level oriented upwind scheme, local head model. • CAP has a function of linked calculation with reactor coolant system code. • CAP code assessments showed appropriate prediction capabilities. - Abstract: CAP (nuclear Containment Analysis Package) code has been developed in Korean nuclear society for the analysis of nuclear containment thermal hydraulic behaviors including pressure and temperature trends and hydrogen concentration. Lumped model of CAP code uses 2-phase, 3-field equations for fluid behaviors, and has appropriate constitutive equations, 1-dimensional heat conductor model, component models, trip and control models, and special process models. CAP can run in a standalone mode or a linked mode with a reactor coolant system analysis code. The linked mode enables the more realistic calculation of a containment response and is expected to be applicable to a more complicated advanced plant design calculation. CAP code assessments were carried out by gradual approaches: conceptual problems, fundamental phenomena, component and principal phenomena, experimental validation, and finally comparison with other code calculations on the base of important phenomena identifications. The assessments showed appropriate prediction capabilities of CAP

Time-varying parameter models for catchments with land use change: the importance of model structure

Science.gov (United States)

Pathiraja, Sahani; Anghileri, Daniela; Burlando, Paolo; Sharma, Ashish; Marshall, Lucy; Moradkhani, Hamid

2018-05-01

Rapid population and economic growth in Southeast Asia has been accompanied by extensive land use change with consequent impacts on catchment hydrology. Modeling methodologies capable of handling changing land use conditions are therefore becoming ever more important and are receiving increasing attention from hydrologists. A recently developed data-assimilation-based framework that allows model parameters to vary through time in response to signals of change in observations is considered for a medium-sized catchment (2880 km2) in northern Vietnam experiencing substantial but gradual land cover change. We investigate the efficacy of the method as well as the importance of the chosen model structure in ensuring the success of a time-varying parameter method. The method was used with two lumped daily conceptual models (HBV and HyMOD) that gave good-quality streamflow predictions during pre-change conditions. Although both time-varying parameter models gave improved streamflow predictions under changed conditions compared to the time-invariant parameter model, persistent biases for low flows were apparent in the HyMOD case. It was found that HyMOD was not suited to representing the modified baseflow conditions, resulting in extreme and unrealistic time-varying parameter estimates. This work shows that the chosen model can be critical for ensuring the time-varying parameter framework successfully models streamflow under changing land cover conditions. It can also be used to determine whether land cover changes (and not just meteorological factors) contribute to the observed hydrologic changes in retrospective studies where the lack of a paired control catchment precludes such an assessment.

Time-varying parameter models for catchments with land use change: the importance of model structure

Directory of Open Access Journals (Sweden)

S. Pathiraja

2018-05-01

Full Text Available Rapid population and economic growth in Southeast Asia has been accompanied by extensive land use change with consequent impacts on catchment hydrology. Modeling methodologies capable of handling changing land use conditions are therefore becoming ever more important and are receiving increasing attention from hydrologists. A recently developed data-assimilation-based framework that allows model parameters to vary through time in response to signals of change in observations is considered for a medium-sized catchment (2880 km2 in northern Vietnam experiencing substantial but gradual land cover change. We investigate the efficacy of the method as well as the importance of the chosen model structure in ensuring the success of a time-varying parameter method. The method was used with two lumped daily conceptual models (HBV and HyMOD that gave good-quality streamflow predictions during pre-change conditions. Although both time-varying parameter models gave improved streamflow predictions under changed conditions compared to the time-invariant parameter model, persistent biases for low flows were apparent in the HyMOD case. It was found that HyMOD was not suited to representing the modified baseflow conditions, resulting in extreme and unrealistic time-varying parameter estimates. This work shows that the chosen model can be critical for ensuring the time-varying parameter framework successfully models streamflow under changing land cover conditions. It can also be used to determine whether land cover changes (and not just meteorological factors contribute to the observed hydrologic changes in retrospective studies where the lack of a paired control catchment precludes such an assessment.

28 CFR 523.16 - Lump sum awards.

Science.gov (United States)

2010-07-01

... satisfactory performance of an unusually hazardous assignment; (c) An act which protects the lives of staff or... TRANSFER COMPUTATION OF SENTENCE Extra Good Time § 523.16 Lump sum awards. Any staff member may recommend... award is calculated. No seniority is accrued for such awards. Staff may recommend lump sum awards of...

Parameter identification and model validation for the piezoelectric actuator in an inertia motor

International Nuclear Information System (INIS)

Hunstig, Matthias; Hemsel, Tobias

2010-01-01

Piezoelectric inertia motors make use of the inertia of a slider to drive the slider by friction contact in a series of small steps which are generally composed of a stick phase and a slip phase. If the best electrical drive signal for the piezoelectric actuator in an inertia motor is to be determined, its dynamical behaviour must be known. A classic dynamic lumped parameter model for piezoelectric actuators is valid only in resonance and, therefore, is not suitable for modelling the actuator in an inertia motor. A reduced dynamic model is used instead. Its parameters are identified using a step response measurement. This model is used to predict the movement of the actuator in response to a velocity-optimized signal introduced in a separate contribution. Results show that the model cannot represent the dynamical characteristics of the actuator completely. For determining voltage signals that let piezoelectric actuators follow a calculated movement pattern exactly, the model can, therefore, only be used with limitations.

Representing Lumped Markov Chains by Minimal Polynomials over Field GF(q)

Science.gov (United States)

Zakharov, V. M.; Shalagin, S. V.; Eminov, B. F.

2018-05-01

A method has been proposed to represent lumped Markov chains by minimal polynomials over a finite field. The accuracy of representing lumped stochastic matrices, the law of lumped Markov chains depends linearly on the minimum degree of polynomials over field GF(q). The method allows constructing the realizations of lumped Markov chains on linear shift registers with a pre-defined “linear complexity”.

General 3D Lumped Thermal Model with Various Boundary Conditions for High Power IGBT Modules

DEFF Research Database (Denmark)

Bahman, Amir Sajjad; Ma, Ke; Blaabjerg, Frede

2016-01-01

Accurate thermal dynamics modeling of high power Insulated Gate Bipolar Transistor (IGBT) modules is important information for the reliability analysis and thermal design of power electronic systems. However, the existing thermal models have their limits to correctly predict these complicated...... thermal behaviors in the IGBTs. In this paper, a new three-dimensional (3D) lumped thermal model is proposed, which can easily be characterized from Finite Element Methods (FEM) based simulation and acquire the thermal distribution in critical points. Meanwhile the boundary conditions including...... the cooling system and power losses are modeled in the 3D thermal model, which can be adapted to different real field applications of power electronic converters. The accuracy of the proposed thermal model is verified by experimental results....

Impact of model structure on flow simulation and hydrological realism: from a lumped to a semi-distributed approach

Science.gov (United States)

Garavaglia, Federico; Le Lay, Matthieu; Gottardi, Fréderic; Garçon, Rémy; Gailhard, Joël; Paquet, Emmanuel; Mathevet, Thibault

2017-08-01

Model intercomparison experiments are widely used to investigate and improve hydrological model performance. However, a study based only on runoff simulation is not sufficient to discriminate between different model structures. Hence, there is a need to improve hydrological models for specific streamflow signatures (e.g., low and high flow) and multi-variable predictions (e.g., soil moisture, snow and groundwater). This study assesses the impact of model structure on flow simulation and hydrological realism using three versions of a hydrological model called MORDOR: the historical lumped structure and a revisited formulation available in both lumped and semi-distributed structures. In particular, the main goal of this paper is to investigate the relative impact of model equations and spatial discretization on flow simulation, snowpack representation and evapotranspiration estimation. Comparison of the models is based on an extensive dataset composed of 50 catchments located in French mountainous regions. The evaluation framework is founded on a multi-criterion split-sample strategy. All models were calibrated using an automatic optimization method based on an efficient genetic algorithm. The evaluation framework is enriched by the assessment of snow and evapotranspiration modeling against in situ and satellite data. The results showed that the new model formulations perform significantly better than the initial one in terms of the various streamflow signatures, snow and evapotranspiration predictions. The semi-distributed approach provides better calibration-validation performance for the snow cover area, snow water equivalent and runoff simulation, especially for nival catchments.

Analysis and design of lumped element Marchand baluns

DEFF Research Database (Denmark)

Johansen, Tom Keinicke; Krozer, Viktor

2008-01-01

In this paper a novel design procedure for lumped element Marchand baluns is proposed. An analysis is performed on the balun structure in order to determine the conditions for ideal balun performance in terms of the lumped element values. The analysis is verified by two broadband designs centered...... around 22.75 GHz and differing only in terms of their impedance transformation ratio. EM simulation results on our proposed lumped element Marchand balun structure predicts an insertion loss of 4 dB and return loss of 40 dB at the design frequency of 22.75 GHz. The amplitude and phase imbalance...

Model-order reduction of lumped parameter systems via fractional calculus

Science.gov (United States)

Hollkamp, John P.; Sen, Mihir; Semperlotti, Fabio

2018-04-01

This study investigates the use of fractional order differential models to simulate the dynamic response of non-homogeneous discrete systems and to achieve efficient and accurate model order reduction. The traditional integer order approach to the simulation of non-homogeneous systems dictates the use of numerical solutions and often imposes stringent compromises between accuracy and computational performance. Fractional calculus provides an alternative approach where complex dynamical systems can be modeled with compact fractional equations that not only can still guarantee analytical solutions, but can also enable high levels of order reduction without compromising on accuracy. Different approaches are explored in order to transform the integer order model into a reduced order fractional model able to match the dynamic response of the initial system. Analytical and numerical results show that, under certain conditions, an exact match is possible and the resulting fractional differential models have both a complex and frequency-dependent order of the differential operator. The implications of this type of approach for both model order reduction and model synthesis are discussed.

Correlation of Fukushima data with SSI models

International Nuclear Information System (INIS)

Miller, C.A.; Costantino, C.J.; Philippacopoulos, A.J.

1985-01-01

The seismic response of nuclear power plant structures is often calculated using lumped parameter methods. A finite element model of the structure is coupled to the soil with a spring-dashpot system used to represent the interaction process. The parameters of the interaction model are based on analytic solutions to simple problems which are idealizations of the actual problem. The objective of this work is to compare predicted response using the standard lumped parameter models with experimental data. These comparisons are shown to be good for fairly uniform soil systems. (orig.)

MISTRA facility for containment lumped parameter and CFD codes validation. Example of the International Standard Problem ISP47

International Nuclear Information System (INIS)

Tkatschenko, I.; Studer, E.; Paillere, H.

2005-01-01

During a severe accident in a Pressurized Water Reactor (PWR), the formation of a combustible gas mixture in the complex geometry of the reactor depends on the understanding of hydrogen production, the complex 3D thermal-hydraulics flow due to gas/steam injection, natural convection, heat transfer by condensation on walls and effect of mitigation devices. Numerical simulation of such flows may be performed either by Lumped Parameter (LP) or by Computational Fluid Dynamics (CFD) codes. Advantages and drawbacks of LP and CFD codes are well-known. LP codes are mainly developed for full size containment analysis but they need improvements, especially since they are not able to accurately predict the local gas mixing within the containment. CFD codes require a process of validation on well-instrumented experimental data before they can be used with a high degree of confidence. The MISTRA coupled effect test facility has been built at CEA to fulfil this validation objective: with numerous measurement points in the gaseous volume - temperature, gas concentration, velocity and turbulence - and with well controlled boundary conditions. As illustration of both experimental and simulation areas of this topic, a recent example in the use of MISTRA test data is presented for the case of the International Standard Problem ISP47. The proposed experimental work in the MISTRA facility provides essential data to fill the gaps in the modelling/validation of computational tools. (author)

Uncovering and testing the fuzzy clusters based on lumped Markov chain in complex network.

Science.gov (United States)

Jing, Fan; Jianbin, Xie; Jinlong, Wang; Jinshuai, Qu

2013-01-01

Identifying clusters, namely groups of nodes with comparatively strong internal connectivity, is a fundamental task for deeply understanding the structure and function of a network. By means of a lumped Markov chain model of a random walker, we propose two novel ways of inferring the lumped markov transition matrix. Furthermore, some useful results are proposed based on the analysis of the properties of the lumped Markov process. To find the best partition of complex networks, a novel framework including two algorithms for network partition based on the optimal lumped Markovian dynamics is derived to solve this problem. The algorithms are constructed to minimize the objective function under this framework. It is demonstrated by the simulation experiments that our algorithms can efficiently determine the probabilities with which a node belongs to different clusters during the learning process and naturally supports the fuzzy partition. Moreover, they are successfully applied to real-world network, including the social interactions between members of a karate club.

Pembelajaran Seni Tari Kuda Lumping Di Desa Dukuhwaluh Kecamatan Kembaran Kab. Banyumas

OpenAIRE

Daryanto, Daryanto

2011-01-01

The goals this research were to determine: 1). What are the requirements given to prospective players of Kuda Lumping; 2). What material provided and what methods are used in training Kuda Lumping; 3). What is the cost required to conduct training of Kuda Lumping, and from which source. 4). How long does it take to produce players who are ready to perform Kuda Lumping showcased in front of an audience. From the research result shows that: 1. Requirements given to players of Kuda Lumping...

PEMBELAJARAN SENI TARI KUDA LUMPING DI DESA DUKUHWALUH KECAMATAN KEMBARAN KAB. BANYUMAS

OpenAIRE

Daryanto Daryanto

2011-01-01

The goals this research were to determine: 1). What are the requirements given to prospective players of Kuda Lumping; 2). What material provided and what methods are used in training Kuda Lumping; 3). What is the cost required to conduct training of Kuda Lumping, and from which source. 4). How long does it take to produce players who are ready to perform Kuda Lumping showcased in front of an audience. From the research result shows that: 1. Requirements given to players of Kuda Lumping...

Modeling and analyses of postulated UF6 release accidents in gaseous diffusion plant

International Nuclear Information System (INIS)

Kim, S.H.; Taleyarkhan, R.P.; Keith, K.D.; Schmidt, R.W.; Carter, J.C.; Dyer, R.H.

1995-10-01

Computer models have been developed to simulate the transient behavior of aerosols and vapors as a result of a postulated accident involving the release of uranium hexafluoride (UF 6 ) into the process building of a gaseous diffusion plant. UF 6 undergoes an exothermic chemical reaction with moisture (H 2 O) in the air to form hydrogen fluoride (HF) and radioactive uranyl fluoride (UO 2 F 2 ). As part of a facility-wide safety evaluation, this study evaluated source terms consisting of UO 2 F 2 as well as HF during a postulated UF 6 release accident in a process building. In the postulated accident scenario, ∼7900 kg (17,500 lb) of hot UF 6 vapor is released over a 5 min period from the process piping into the atmosphere of a large process building. UO 2 F 2 mainly remains as airborne-solid particles (aerosols), and HF is in a vapor form. Some UO 2 F 2 aerosols are removed from the air flow due to gravitational settling. The HF and the remaining UO 2 F 2 are mixed with air and exhausted through the building ventilation system. The MELCOR computer code was selected for simulating aerosols and vapor transport in the process building. MELCOR model was first used to develop a single volume representation of a process building and its results were compared with those from past lumped parameter models specifically developed for studying UF 6 release accidents. Preliminary results indicate that MELCOR predicted results (using a lumped formulation) are comparable with those from previously developed models

Lump wood combustion process

Science.gov (United States)

Kubesa, Petr; Horák, Jiří; Branc, Michal; Krpec, Kamil; Hopan, František; Koloničný, Jan; Ochodek, Tadeáš; Drastichová, Vendula; Martiník, Lubomír; Malcho, Milan

2014-08-01

The article deals with the combustion process for lump wood in low-power fireplaces (units to dozens of kW). Such a combustion process is cyclical in its nature, and what combustion facility users are most interested in is the frequency, at which fuel needs to be stoked to the fireplace. The paper defines the basic terms such as burnout curve and burning rate curve, which are closely related to the stocking frequency. The fuel burning rate is directly dependent on the immediate thermal power of the fireplace. This is also related to the temperature achieved in the fireplace, magnitude of flue gas losses and the ability to generate conditions favouring the full burnout of the fuel's combustible component, which, at once ensures the minimum production of combustible pollutants. Another part of the paper describes experiments conducted in traditional fireplaces with a grate, at which well-dried lump wood was combusted.

PEMBELAJARAN SENI TARI KUDA LUMPING DI DESA DUKUHWALUH KECAMATAN KEMBARAN KAB. BANYUMAS

Directory of Open Access Journals (Sweden)

Daryanto Daryanto

2011-03-01

Full Text Available The goals this research were to determine: 1. What are the requirements given to prospective players of Kuda Lumping; 2. What material provided and what methods are used in training Kuda Lumping; 3. What is the cost required to conduct training of Kuda Lumping, and from which source. 4. How long does it take to produce players who are ready to perform Kuda Lumping showcased in front of an audience. From the research result shows that: 1. Requirements given to players of Kuda Lumping (Ebeg, are namely: (1 has Kuda Lumping, (2 can dance in group / compact dance, (3 perform the ritual bathing and diving in rivers and (4 conduct ”Ngasrep” or fasting for 3 (three days without stopping. 2. The practice material was first given to prospective players Kuda Lumping is dance. In practing the dance material, the new dancers were directly guided by the seniors. The method used is by giving examples of dancing by the senior players to prospective players. When giving examples accompanied by gamelan / music, while dancer candidates of Kuda Lumping followed. 3. Fee required for training activities at least IDR 400,000,- (four hundred thousand rupiah. This cost does not include the cost to buy a kuda lumping. Sources of cost comes from the self-help group members of kuda lumping, like dalang ( director of the dance and local people. It means the training and activities of Kuda Lumping, did not receive funding / donations from the government, both the village and district governments. The cost for training activities was used to rent the gamelan, to purchase clothing / costume players, “sesaji”, consumption and honorariums. 4. To train / produce, it take a player at least 3.5 (three and a half months and a maximum of 7 (seven months. This calculation is based on the starting time of dance exercise, until doing the bath in the river as the last stage. Key Wordsi: Kuda lumping, learning ,ngasrep, ritual of bathe, ritual offerings, wayang,

Uncertainty analyses of the calibrated parameter values of a water quality model

Science.gov (United States)

Rode, M.; Suhr, U.; Lindenschmidt, K.-E.

2003-04-01

For river basin management water quality models are increasingly used for the analysis and evaluation of different management measures. However substantial uncertainties exist in parameter values depending on the available calibration data. In this paper an uncertainty analysis for a water quality model is presented, which considers the impact of available model calibration data and the variance of input variables. The investigation was conducted based on four extensive flowtime related longitudinal surveys in the River Elbe in the years 1996 to 1999 with varying discharges and seasonal conditions. For the model calculations the deterministic model QSIM of the BfG (Germany) was used. QSIM is a one dimensional water quality model and uses standard algorithms for hydrodynamics and phytoplankton dynamics in running waters, e.g. Michaelis Menten/Monod kinetics, which are used in a wide range of models. The multi-objective calibration of the model was carried out with the nonlinear parameter estimator PEST. The results show that for individual flow time related measuring surveys very good agreements between model calculation and measured values can be obtained. If these parameters are applied to deviating boundary conditions, substantial errors in model calculation can occur. These uncertainties can be decreased with an increased calibration database. More reliable model parameters can be identified, which supply reasonable results for broader boundary conditions. The extension of the application of the parameter set on a wider range of water quality conditions leads to a slight reduction of the model precision for the specific water quality situation. Moreover the investigations show that highly variable water quality variables like the algal biomass always allow a smaller forecast accuracy than variables with lower coefficients of variation like e.g. nitrate.

Lump Sum Moving Cost and Aggregate Office Space Use

NARCIS (Netherlands)

G. Romijn

1997-01-01

textabstractWhen firms decide to change office space use, in many instances this involves relocation. Relocation involves sizable costs to the firm that can to a large extent be characterized as lump sum, i.e. independent of the change in demand. In this paper we propose and solve a model of the

Comments on lump solutions in SFT

International Nuclear Information System (INIS)

Bonora, Loriano; Tolla, Driba D.

2016-01-01

We analyze a recently proposed scheme to construct analytic lump solutions in open SFT. We argue that in order for the scheme to be operative and to guarantee background independence it must be implemented in the same 2D conformal field theory in which SFT is formulated. We outline and discuss two different possible approaches. Next we reconsider an older proposal for analytic lump solutions and implement a few improvements. In the course of the analysis we formulate a distinction between regular and singular gauge transformations and advocate the necessity of defining a topology in the space of string fields. (orig.)

Comments on lump solutions in SFT

Energy Technology Data Exchange (ETDEWEB)

Bonora, Loriano; Tolla, Driba D. [International School for Advanced Studies (SISSA), Trieste (Italy); INFN, Sezione di Trieste, Trieste (Italy)

2016-04-15

We analyze a recently proposed scheme to construct analytic lump solutions in open SFT. We argue that in order for the scheme to be operative and to guarantee background independence it must be implemented in the same 2D conformal field theory in which SFT is formulated. We outline and discuss two different possible approaches. Next we reconsider an older proposal for analytic lump solutions and implement a few improvements. In the course of the analysis we formulate a distinction between regular and singular gauge transformations and advocate the necessity of defining a topology in the space of string fields. (orig.)

Model parameters estimation and sensitivity by genetic algorithms

International Nuclear Information System (INIS)

Marseguerra, Marzio; Zio, Enrico; Podofillini, Luca

2003-01-01

In this paper we illustrate the possibility of extracting qualitative information on the importance of the parameters of a model in the course of a Genetic Algorithms (GAs) optimization procedure for the estimation of such parameters. The Genetic Algorithms' search of the optimal solution is performed according to procedures that resemble those of natural selection and genetics: an initial population of alternative solutions evolves within the search space through the four fundamental operations of parent selection, crossover, replacement, and mutation. During the search, the algorithm examines a large amount of solution points which possibly carries relevant information on the underlying model characteristics. A possible utilization of this information amounts to create and update an archive with the set of best solutions found at each generation and then to analyze the evolution of the statistics of the archive along the successive generations. From this analysis one can retrieve information regarding the speed of convergence and stabilization of the different control (decision) variables of the optimization problem. In this work we analyze the evolution strategy followed by a GA in its search for the optimal solution with the aim of extracting information on the importance of the control (decision) variables of the optimization with respect to the sensitivity of the objective function. The study refers to a GA search for optimal estimates of the effective parameters in a lumped nuclear reactor model of literature. The supporting observation is that, as most optimization procedures do, the GA search evolves towards convergence in such a way to stabilize first the most important parameters of the model and later those which influence little the model outputs. In this sense, besides estimating efficiently the parameters values, the optimization approach also allows us to provide a qualitative ranking of their importance in contributing to the model output. The

Some error estimates for the lumped mass finite element method for a parabolic problem

KAUST Repository

Chatzipantelidis, P.

2012-01-01

We study the spatially semidiscrete lumped mass method for the model homogeneous heat equation with homogeneous Dirichlet boundary conditions. Improving earlier results we show that known optimal order smooth initial data error estimates for the standard Galerkin method carry over to the lumped mass method whereas nonsmooth initial data estimates require special assumptions on the triangulation. We also discuss the application to time discretization by the backward Euler and Crank-Nicolson methods. © 2011 American Mathematical Society.

Forced vibration tests and simulation analyses of a nuclear reactor building. Part 2: simulation analyses

International Nuclear Information System (INIS)

Kuno, M.; Nakagawa, S.; Momma, T.; Naito, Y.; Niwa, M.; Motohashi, S.

1995-01-01

Forced vibration tests of a BWR-type reactor building. Hamaoka Unit 4, were performed. Valuable data on the dynamic characteristics of the soil-structure interaction system were obtained through the tests. Simulation analyses of the fundamental dynamic characteristics of the soil-structure system were conducted, using a basic lumped mass soil-structure model (lattice model), and strong correlation with the measured data was obtained. Furthermore, detailed simulation models were employed to investigate the effects of simultaneously induced vertical response and response of the adjacent turbine building on the lateral response of the reactor building. (author). 4 refs., 11 figs

Optimum Design and Operation of Cyclic Storage Systems; Lumped Approach

Directory of Open Access Journals (Sweden)

Leila Ostadrahimi

2007-01-01

Full Text Available Conjunctive use of surface and groundwater resources is a preferred approach in water resources management. Compared to dam construction, groundwater has certain advantages, among which are less costs, less sedimentation and evaporation, fewer water quality problems, and less social and cultural problems. To reduce the major problems associated with the development of large-scale surface impoundment systems, cyclic storage systems can be used as an alternative. A cyclic storage system (CYCS is an integrated interactive system consisting of two subsystems of surface water storage (reservoir and groundwater; this system together with artificial recharge is able to satisfy the predefined demands with rather high reliability. In order to optimize these systems, one must consider the hydraulic interactions between all the components, but unfortunately it has been neglected in many studies. In this article, a nonlinear optimization model for design and operation of cyclic storage systems has been developed using the lumped approach. In order to evaluate the model, its results have been compared with the results of a model in which distributed approach had been deployed, and so the efficiency of lumped models to solve the problems of cyclic storage systems has been investigated.

Assessing the accuracy of subject-specific, muscle-model parameters determined by optimizing to match isometric strength.

Science.gov (United States)

DeSmitt, Holly J; Domire, Zachary J

2016-12-01

Biomechanical models are sensitive to the choice of model parameters. Therefore, determination of accurate subject specific model parameters is important. One approach to generate these parameters is to optimize the values such that the model output will match experimentally measured strength curves. This approach is attractive as it is inexpensive and should provide an excellent match to experimentally measured strength. However, given the problem of muscle redundancy, it is not clear that this approach generates accurate individual muscle forces. The purpose of this investigation is to evaluate this approach using simulated data to enable a direct comparison. It is hypothesized that the optimization approach will be able to recreate accurate muscle model parameters when information from measurable parameters is given. A model of isometric knee extension was developed to simulate a strength curve across a range of knee angles. In order to realistically recreate experimentally measured strength, random noise was added to the modeled strength. Parameters were solved for using a genetic search algorithm. When noise was added to the measurements the strength curve was reasonably recreated. However, the individual muscle model parameters and force curves were far less accurate. Based upon this examination, it is clear that very different sets of model parameters can recreate similar strength curves. Therefore, experimental variation in strength measurements has a significant influence on the results. Given the difficulty in accurately recreating individual muscle parameters, it may be more appropriate to perform simulations with lumped actuators representing similar muscles.

Multi-objective genetic algorithm parameter estimation in a reduced nuclear reactor model

Energy Technology Data Exchange (ETDEWEB)

Marseguerra, M.; Zio, E.; Canetta, R. [Polytechnic of Milan, Dept. of Nuclear Engineering, Milano (Italy)

2005-07-01

The fast increase in computing power has rendered, and will continue to render, more and more feasible the incorporation of dynamics in the safety and reliability models of complex engineering systems. In particular, the Monte Carlo simulation framework offers a natural environment for estimating the reliability of systems with dynamic features. However, the time-integration of the dynamic processes may render the Monte Carlo simulation quite burdensome so that it becomes mandatory to resort to validated, simplified models of process evolution. Such models are typically based on lumped effective parameters whose values need to be suitably estimated so as to best fit to the available plant data. In this paper we propose a multi-objective genetic algorithm approach for the estimation of the effective parameters of a simplified model of nuclear reactor dynamics. The calibration of the effective parameters is achieved by best fitting the model responses of the quantities of interest to the actual evolution profiles. A case study is reported in which the real reactor is simulated by the QUAndry based Reactor Kinetics (Quark) code available from the Nuclear Energy Agency and the simplified model is based on the point kinetics approximation to describe the neutron balance in the core and on thermal equilibrium relations to describe the energy exchange between the different loops. (authors)

Multi-objective genetic algorithm parameter estimation in a reduced nuclear reactor model

International Nuclear Information System (INIS)

Marseguerra, M.; Zio, E.; Canetta, R.

2005-01-01

The fast increase in computing power has rendered, and will continue to render, more and more feasible the incorporation of dynamics in the safety and reliability models of complex engineering systems. In particular, the Monte Carlo simulation framework offers a natural environment for estimating the reliability of systems with dynamic features. However, the time-integration of the dynamic processes may render the Monte Carlo simulation quite burdensome so that it becomes mandatory to resort to validated, simplified models of process evolution. Such models are typically based on lumped effective parameters whose values need to be suitably estimated so as to best fit to the available plant data. In this paper we propose a multi-objective genetic algorithm approach for the estimation of the effective parameters of a simplified model of nuclear reactor dynamics. The calibration of the effective parameters is achieved by best fitting the model responses of the quantities of interest to the actual evolution profiles. A case study is reported in which the real reactor is simulated by the QUAndry based Reactor Kinetics (Quark) code available from the Nuclear Energy Agency and the simplified model is based on the point kinetics approximation to describe the neutron balance in the core and on thermal equilibrium relations to describe the energy exchange between the different loops. (authors)

Experimental realization of optical lumped nanocircuits at infrared wavelengths.

Science.gov (United States)

Sun, Yong; Edwards, Brian; Alù, Andrea; Engheta, Nader

2012-01-29

The integration of radiofrequency electronic methodologies on micro- as well as nanoscale platforms is crucial for information processing and data-storage technologies. In electronics, radiofrequency signals are controlled and manipulated by 'lumped' circuit elements, such as resistors, inductors and capacitors. In earlier work, we theoretically proposed that optical nanostructures, when properly designed and judiciously arranged, could behave as nanoscale lumped circuit elements--but at optical frequencies. Here, for the first time we experimentally demonstrate a two-dimensional optical nanocircuit at mid-infrared wavelengths. With the guidance of circuit theory, we design and fabricate arrays of Si3N4 nanorods with specific deep subwavelength cross-sections, quantitatively evaluate their equivalent impedance as lumped circuit elements in the mid-infrared regime, and by Fourier transform infrared spectroscopy show that these nanostructures can indeed function as two-dimensional optical lumped circuit elements. We further show that the connections among nanocircuit elements, in particular whether they are in series or in parallel combination, can be controlled by the polarization of impinging optical signals, realizing the notion of 'stereo-circuitry' in metatronics-metamaterials-inspired optical circuitry.

Multi-Site Calibration of Linear Reservoir Based Geomorphologic Rainfall-Runoff Models

Directory of Open Access Journals (Sweden)

Bahram Saeidifarzad

2014-09-01

Full Text Available Multi-site optimization of two adapted event-based geomorphologic rainfall-runoff models was presented using Non-dominated Sorting Genetic Algorithm (NSGA-II method for the South Fork Eel River watershed, California. The first model was developed based on Unequal Cascade of Reservoirs (UECR and the second model was presented as a modified version of Geomorphological Unit Hydrograph based on Nash’s model (GUHN. Two calibration strategies were considered as semi-lumped and semi-distributed for imposing (or unimposing the geomorphology relations in the models. The results of models were compared with Nash’s model. Obtained results using the observed data of two stations in the multi-site optimization framework showed reasonable efficiency values in both the calibration and the verification steps. The outcomes also showed that semi-distributed calibration of the modified GUHN model slightly outperformed other models in both upstream and downstream stations during calibration. Both calibration strategies for the developed UECR model during the verification phase showed slightly better performance in the downstream station, but in the upstream station, the modified GUHN model in the semi-lumped strategy slightly outperformed the other models. The semi-lumped calibration strategy could lead to logical lag time parameters related to the basin geomorphology and may be more suitable for data-based statistical analyses of the rainfall-runoff process.

The role of men in early detection of their spouses' breast lump(s ...

African Journals Online (AJOL)

We aim to determine whether men can be of help in the early detection of lumps in their spouses' breast. 230 questionnaires were administered to married men. The responses were accepted as “yes” or “no. 217 men (94.35%) responded. 195 (89.86%) were aware of breast cancer. 212 ( 97.7%) were either Christians or ...

Rutting resistance of asphalt mixture with cup lumps modified binder

Science.gov (United States)

Shaffie, E.; Hanif, W. M. M. Wan; Arshad, A. K.; Hashim, W.

2017-11-01

Rutting is the most common pavement distress in pavement structures which occurs mainly due to several factors such as increasing of traffic volume, climatic conditions and also due to construction design errors. This failure reduced the service life of the pavement, reduced driver safety and increase cost of maintenance. Polymer Modified Binder has been observed for a long time in improving asphalt pavement performance. Research shows that the use of polymer in bituminous mix not only improve the resistance to rutting but also increase the life span of the pavement. This research evaluates the physical properties and rutting performance of dense graded Superpave-designed HMA mix. Two different types of dense graded Superpave HMA mix were developed consists of unmodified binder mix (UMB) and cup lumps rubber (liquid form) modified binder mix (CLMB). Natural rubber polymer modified binder was prepared from addition of 8 percent of cup lumps into binder. Results showed that all the mixes passed the Superpave volumetric properties criteria which indicate that these mixtures were good with respect to durability and flexibility. Furthermore, rutting results from APA rutting test was determined to evaluate the performance of these mixtures. The rutting result of CLMB demonstrates better resistance to rutting than those prepared using UMB mix. Addition of cup lumps rubber in asphalt mixture was found to be significant, where the cup lumps rubber has certainly improves the binder properties and enhanced its rutting resistance due to greater elasticity offered by the cup lumps rubber particles. It shows that the use of cup lumps rubber can significantly reduce the rut depth of asphalt mixture by 41% compared to the minimum rut depth obtained for the UMB mix. Therefore, it can be concluded that the cup lumps rubber is suitable to be used as a modifier to modified binder in order to enhance the properties of the binder and thus improves the performance of asphalt mixes.

Structured modelling and nonlinear analysis of PEM fuel cells; Strukturierte Modellierung und nichtlineare Analyse von PEM-Brennstoffzellen

Energy Technology Data Exchange (ETDEWEB)

Hanke-Rauschenbach, R.

2007-10-26

In the first part of this work a model structuring concept for electrochemical systems is presented. The application of such a concept for the structuring of a process model allows it to combine different fuel cell models to form a whole model family, regardless of their level of detail. Beyond this the concept offers the opportunity to flexibly exchange model entities on different model levels. The second part of the work deals with the nonlinear behaviour of PEM fuel cells. With the help of a simple, spatially lumped and isothermal model, bistable current-voltage characteristics of PEM fuel cells operated with low humidified feed gases are predicted and discussed in detail. The cell is found to exhibit current-voltage curves with pronounced local extrema in a parameter range that is of practical interest when operated at constant feed gas flow rates. (orig.)

An enhanced lumped element electrical model of a double barrier memristive device

International Nuclear Information System (INIS)

Solan, Enver; Ochs, Karlheinz; Dirkmann, Sven; Hansen, Mirko; Kohlstedt, Hermann; Ziegler, Martin; Schroeder, Dietmar; Mussenbrock, Thomas

2017-01-01

The massive parallel approach of neuromorphic circuits leads to effective methods for solving complex problems. It has turned out that resistive switching devices with a continuous resistance range are potential candidates for such applications. These devices are memristive systems—nonlinear resistors with memory. They are fabricated in nanotechnology and hence parameter spread during fabrication may aggravate reproducible analyses. This issue makes simulation models of memristive devices worthwhile. Kinetic Monte-Carlo simulations based on a distributed model of the device can be used to understand the underlying physical and chemical phenomena. However, such simulations are very time-consuming and neither convenient for investigations of whole circuits nor for real-time applications, e.g. emulation purposes. Instead, a concentrated model of the device can be used for both fast simulations and real-time applications, respectively. We introduce an enhanced electrical model of a valence change mechanism (VCM) based double barrier memristive device (DBMD) with a continuous resistance range. This device consists of an ultra-thin memristive layer sandwiched between a tunnel barrier and a Schottky-contact. The introduced model leads to very fast simulations by using usual circuit simulation tools while maintaining physically meaningful parameters. Kinetic Monte-Carlo simulations based on a distributed model and experimental data have been utilized as references to verify the concentrated model. (paper)

Energy-state formulation of lumped volume dynamic equations with application to a simplified free piston Stirling engine

Science.gov (United States)

Daniele, C. J.; Lorenzo, C. F.

1979-01-01

Lumped volume dynamic equations are derived using an energy-state formulation. This technique requires that kinetic and potential energy state functions be written for the physical system being investigated. To account for losses in the system, a Rayleigh dissipation function is also formed. Using these functions, a Lagrangian is formed and using Lagrange's equation, the equations of motion for the system are derived. The results of the application of this technique to a lumped volume are used to derive a model for the free-piston Stirling engine. The model was simplified and programmed on an analog computer. Results are given comparing the model response with experimental data.

Monte Carlo parameter studies and uncertainty analyses with MCNP5

International Nuclear Information System (INIS)

Brown, F. B.; Sweezy, J. E.; Hayes, R.

2004-01-01

A software tool called mcnp p study has been developed to automate the setup, execution, and collection of results from a series of MCNP5 Monte Carlo calculations. This tool provides a convenient means of performing parameter studies, total uncertainty analyses, parallel job execution on clusters, stochastic geometry modeling, and other types of calculations where a series of MCNP5 jobs must be performed with varying problem input specifications. (authors)

Lumped transmission line avalanche pulser

Science.gov (United States)

Booth, Rex

1995-01-01

A lumped linear avalanche transistor pulse generator utilizes stacked transistors in parallel within a stage and couples a plurality of said stages, in series with increasing zener diode limited voltages per stage and decreasing balanced capacitance load per stage to yield a high voltage, high and constant current, very short pulse.

Generalized Kutta–Joukowski theorem for multi-vortex and multi-airfoil flow (a lumped vortex model

Directory of Open Access Journals (Sweden)

Bai Chenyuan

2014-02-01

Full Text Available For purpose of easy identification of the role of free vortices on the lift and drag and for purpose of fast or engineering evaluation of forces for each individual body, we will extend in this paper the Kutta–Joukowski (KJ theorem to the case of inviscid flow with multiple free vortices and multiple airfoils. The major simplification used in this paper is that each airfoil is represented by a lumped vortex, which may hold true when the distances between vortices and bodies are large enough. It is found that the Kutta–Joukowski theorem still holds provided that the local freestream velocity and the circulation of the bound vortex are modified by the induced velocity due to the outside vortices and airfoils. We will demonstrate how to use the present result to identify the role of vortices on the forces according to their position, strength and rotation direction. Moreover, we will apply the present results to a two-cylinder example of Crowdy and the Wagner example to demonstrate how to perform fast force approximation for multi-body and multi-vortex problems. The lumped vortex assumption has the advantage of giving such kinds of approximate results which are very easy to use. The lack of accuracy for such a fast evaluation will be compensated by a rigorous extension, with the lumped vortex assumption removed and with vortex production included, in a forthcoming paper.

20 CFR 222.44 - Other relationship determinations for lump-sum payments.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Other relationship determinations for lump... THE RAILROAD RETIREMENT ACT FAMILY RELATIONSHIPS Relationship as Parent, Grandchild, Brother or Sister... have the relationships to the employee shown below for lump-sum payment purposes: (a) Grandchildren. A...

Incidence of malignancy in females presenting with breast lumps in OPD: a study of 277 cases

International Nuclear Information System (INIS)

Chaudhary, I.A.; Qureshi, S.K.; Rasul, S.

2003-01-01

Objective: To find the incidence of malignancy in females presenting with breast lumps in surgical out patient and to find out the age related incidence of benign and malignant diseases in these patients. Patients and Methods: All cases reporting to surgical outdoor with breast lumps were included and underwent investigation for the breast lumps to determine the histopathological diagnosis. Results: A total of 277 cases were studied. 24.2% breast lumps were malignant and 75.8% were benign. The incidence of malignancy increases from 0% in 2nd decade to 38.9% in 5th and 100% in 9th decade of life. The probability of diagnosing a breast lump as a malignant is one in three in 4th decade, two in five in 5th decade and more than one in two there after. Fibrocystic disease (33.8%) and Fibro adenoma (27.1%) was the commonest finding among the benign lumps. Among malignant lumps infiltrating duct carcinoma (68.7%) is the commonest finding. Conclusion: There is a significantly high incidence of malignant breast lumps after the 3rd decade of life and it increases subsequently. It is recommended that the surgeon managing a case of breast lump in a patient above 30 years should be highly suspicious and cautious so that early detection and management of malignant lumps be carried out. (author)

Influence of Population Variation of Physiological Parameters in Computational Models of Space Physiology

Science.gov (United States)

Myers, J. G.; Feola, A.; Werner, C.; Nelson, E. S.; Raykin, J.; Samuels, B.; Ethier, C. R.

2016-01-01

The earliest manifestations of Visual Impairment and Intracranial Pressure (VIIP) syndrome become evident after months of spaceflight and include a variety of ophthalmic changes, including posterior globe flattening and distension of the optic nerve sheath. Prevailing evidence links the occurrence of VIIP to the cephalic fluid shift induced by microgravity and the subsequent pressure changes around the optic nerve and eye. Deducing the etiology of VIIP is challenging due to the wide range of physiological parameters that may be influenced by spaceflight and are required to address a realistic spectrum of physiological responses. Here, we report on the application of an efficient approach to interrogating physiological parameter space through computational modeling. Specifically, we assess the influence of uncertainty in input parameters for two models of VIIP syndrome: a lumped-parameter model (LPM) of the cardiovascular and central nervous systems, and a finite-element model (FEM) of the posterior eye, optic nerve head (ONH) and optic nerve sheath. Methods: To investigate the parameter space in each model, we employed Latin hypercube sampling partial rank correlation coefficient (LHSPRCC) strategies. LHS techniques outperform Monte Carlo approaches by enforcing efficient sampling across the entire range of all parameters. The PRCC method estimates the sensitivity of model outputs to these parameters while adjusting for the linear effects of all other inputs. The LPM analysis addressed uncertainties in 42 physiological parameters, such as initial compartmental volume and nominal compartment percentage of total cardiac output in the supine state, while the FEM evaluated the effects on biomechanical strain from uncertainties in 23 material and pressure parameters for the ocular anatomy. Results and Conclusion: The LPM analysis identified several key factors including high sensitivity to the initial fluid distribution. The FEM study found that intraocular pressure and

Modeling of nanofabricated paddle bridges for resonant mass sensing

International Nuclear Information System (INIS)

Lobontiu, N.; Ilic, B.; Garcia, E.; Reissman, T.; Craighead, H. G.

2006-01-01

The modeling of nanopaddle bridges is studied in this article by proposing a lumped-parameter mathematical model which enables structural characterization in the resonant domain. The distributed compliance and inertia of all three segments composing a paddle bridge are taken into consideration in order to determine the equivalent lumped-parameter stiffness and inertia fractions, and further on the bending and torsion resonant frequencies. The approximate model produces results which are confirmed by finite element analysis and experimental measurements. The model is subsequently utilized to quantify the amount of mass which attaches to the bridge by predicting the modified resonant frequencies in either bending or torsion

Preparation of lumped fission product (FP) cross sections for a multigroup library

International Nuclear Information System (INIS)

Ono, S.; Corcuera, R.P.

1984-01-01

A method for the calculation of lumped Fission Product (FP) cross sections has been developed. The group constants fo each nuclide are generated by NJOY code, based on ENDF/B-V data. In this first version, cross section of 28 nuclides are lumped for typical characteristics of Binary Breeder Reactor (BBR). One energy group calculations are made for a 1000 MWe fast reactor to verify the influence of burnup, number of FP and fuel composition on the lumped fission product cross sections. (Author) [pt

Reduction in thermal conductivity of BiSbTe lump

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Kaleem [King Saud University, Sustainable Energy Technologies Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia); Wan, C. [Tsinghua University, State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Beijing (China); Al-Eshaikh, M.A.; Kadachi, A.N. [King Saud University, Research Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia)

2017-03-15

In this work, systematic investigations on the thermal conductivities of BiSbTe lump, microstructured pristine BiSbTe bulk and single wall carbon nanotubes (SWCNTs)/BiSbTe bulk nanocomposites were performed. BiSbTe lumps were crushed to form a coarse powder (200 μm) and effect of particle size reduction on the effective thermal conductivity of BiSbTe (200 μm) bulk were analyzed. For further reduction in the conductivity, a two pronged strategy has been employed. First, additional refinement of BiSbTe (200 μm) were performed through ball milling in an inert environment. Second, SWCNTs in 0.75, and 1.0 vol% were distributed uniformly in the fine BiSbTe ball milled powder. The results showed that the effective thermal conductivities decrease with the reduction in the particle size from lump to BiSbTe (200 μm) bulk as well as with the addition of SWCNTs accompanied by further refinement of BiSbTe particles. The significant reduction in thermal conductivities of the lump was achieved for pure BiSbTe (200 μm) bulk and 0.75 vol% of SWCNTs/BiSbTe composite. This can be ascribed to the enhanced phonon scattering by the grain boundaries between the nanostructured BiSbTe particles as well as the interfaces between BiSbTe and the low dimensional carbon nanotubes. (orig.)

Simulations of hydrogen distribution experiments using the PRESCON2 and GOTHIC codes

International Nuclear Information System (INIS)

Nguyen, T.H.; Collins, W.M.

1994-01-01

The main objective of this work is to develop modelling guidelines in the use of containment models to more accurately predict hydrogen distribution in the HDR facility and to assess the ability of both lumped and distributed parameter models in predicting natural convective flows within containment. Experiences learned from this exercise will be applied to present methodologies used in licensing analyses for CANDU containments. PRESCON2 simulations of hydrogen distribution experiments performed in the HDR facility show hydrogen and helium concentrations are under-predicted at high elevations and over predicted at low elevations. Acceptable predictions of the gas concentration are obtained in the vicinity of the release. Results obtained from GOTHIC simulations using lumped parameter models are very comparable to those predicted by PRESCON2. This indicates that lumped parameter codes tend to over-estimate the degree of mixing of fluids due to the inherent nodal atmospheric homogeneity assumption in their numerical formulation. Results obtained from the GOTHIC simulation using a simple distributed parameter model show little improvement compared to those predicted using the lumped parameter model. This indicates that a simple 3-D model will not be sufficient to make significant improvements in the results. More detailed modelling of the junction flows and finer grids should lead to more accurate results. More detailed investigations employing finer 3-D meshes is under investigation. (author)

RRAWFLOW: Rainfall-Response Aquifer and Watershed Flow Model (v1.11)

Science.gov (United States)

Long, A. J.

2014-09-01

The Rainfall-Response Aquifer and Watershed Flow Model (RRAWFLOW) is a lumped-parameter model that simulates streamflow, springflow, groundwater level, solute transport, or cave drip for a measurement point in response to a system input of precipitation, recharge, or solute injection. The RRAWFLOW open-source code is written in the R language and is included in the Supplement to this article along with an example model of springflow. RRAWFLOW includes a time-series process to estimate recharge from precipitation and simulates the response to recharge by convolution; i.e., the unit hydrograph approach. Gamma functions are used for estimation of parametric impulse-response functions (IRFs); a combination of two gamma functions results in a double-peaked IRF. A spline fit to a set of control points is introduced as a new method for estimation of nonparametric IRFs. Other options include the use of user-defined IRFs and different methods to simulate time-variant systems. For many applications, lumped models simulate the system response with equal accuracy to that of distributed models, but moreover, the ease of model construction and calibration of lumped models makes them a good choice for many applications. RRAWFLOW provides professional hydrologists and students with an accessible and versatile tool for lumped-parameter modeling.

Numerical analysis of macro-crack formation behavior within the lump coke; Cokes sonai kiretsu shinten kiko no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Aoki, H; Sato, H; Miura, T [Tohoku University, Sendai (Japan). Faculty of Engineering

1995-03-15

The thermal stress analysis within lump coke was studied in order to investigate macro-crack formation and deformation behavior which strongly influence heat and mass transfer in a coke oven chamber. The dilatation of plastic layer, heating rate dependence of thermophysical and mechanical properties of coal/coke, creep in the plastic and semi-coke layers, macro-crack propagation and radiative heat transfer within the macro-crack were considered in an analytical model. The macro-crack propagation was determined from the estimated crack tip stress intensity factor, K{sub I}, at the macro-crack tip compared with the plane strain fracture toughness, K{sub IC}, through the unsteady-state calculation. Calculated results on crack formation and deformation behavior of lump coke were in good agreement with experimental observations in a laboratory-scale oven chamber. The analytical model could predict micro-crack formation within the lump coke normal to the heated wall and the coke surface close to the heated wall. 12 refs., 13 figs.

29 CFR Appendix A to Part 4022 - Lump Sum Mortality Rates

Science.gov (United States)

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Lump Sum Mortality Rates A Appendix A to Part 4022 Labor Regulations Relating to Labor (Continued) PENSION BENEFIT GUARANTY CORPORATION COVERAGE AND BENEFITS BENEFITS PAYABLE IN TERMINATED SINGLE-EMPLOYER PLANS Pt. 4022, App. A Appendix A to Part 4022—Lump Sum Mortality...

Parametric uncertainty and global sensitivity analysis in a model of the carotid bifurcation: Identification and ranking of most sensitive model parameters.

Science.gov (United States)

Gul, R; Bernhard, S

2015-11-01

In computational cardiovascular models, parameters are one of major sources of uncertainty, which make the models unreliable and less predictive. In order to achieve predictive models that allow the investigation of the cardiovascular diseases, sensitivity analysis (SA) can be used to quantify and reduce the uncertainty in outputs (pressure and flow) caused by input (electrical and structural) model parameters. In the current study, three variance based global sensitivity analysis (GSA) methods; Sobol, FAST and a sparse grid stochastic collocation technique based on the Smolyak algorithm were applied on a lumped parameter model of carotid bifurcation. Sensitivity analysis was carried out to identify and rank most sensitive parameters as well as to fix less sensitive parameters at their nominal values (factor fixing). In this context, network location and temporal dependent sensitivities were also discussed to identify optimal measurement locations in carotid bifurcation and optimal temporal regions for each parameter in the pressure and flow waves, respectively. Results show that, for both pressure and flow, flow resistance (R), diameter (d) and length of the vessel (l) are sensitive within right common carotid (RCC), right internal carotid (RIC) and right external carotid (REC) arteries, while compliance of the vessels (C) and blood inertia (L) are sensitive only at RCC. Moreover, Young's modulus (E) and wall thickness (h) exhibit less sensitivities on pressure and flow at all locations of carotid bifurcation. Results of network location and temporal variabilities revealed that most of sensitivity was found in common time regions i.e. early systole, peak systole and end systole. Copyright © 2015 Elsevier Inc. All rights reserved.

Fundamentals of electromagnetics 1 internal behavior of lumped elements

CERN Document Server

Voltmer, David

2007-01-01

This book is the first of two volumes which have been created to provide an understanding of the basic principles and applications of electromagnetic fields for electrical engineering students. Fundamentals of Electromagnetics Vol 1: Internal Behavior of Lumped Elements focuses upon the DC and low-frequency behavior of electromagnetic fields within lumped elements. The properties of electromagnetic fields provide the basis for predicting the terminal characteristics of resistors, capacitors, and inductors. The properties of magnetic circuits are included as well. For slightly higher frequencie

EVALUATION OF ANAEMIA USING RED CELL AND RETICULOCYTE PARAMETERS USING AUTOMATED HAEMATOLOGY ANALYSER

Directory of Open Access Journals (Sweden)

Vidyadhar Rao

2016-06-01

Full Text Available Use of current models of Automated Haematology Analysers help in calculating the haemoglobin contents of the mature Red cells, Reticulocytes and percentages of Microcytic and hypochromic Red cells. This has helped the clinician in reaching early diagnosis and management of Different haemopoietic disorders like Iron Deficiency Anaemia, Thalassaemia and anaemia of chronic diseases. AIM This study is conducted using an Automated Haematology Analyser to evaluate anaemia using the Red Cell and Reticulocyte parameters. Three types of anaemia were evaluated; iron deficiency anaemia, anaemia of long duration and anaemia associated with chronic disease and Iron deficiency. MATERIALS AND METHODS The blood samples were collected from 287 adult patients with anaemia differentiated depending upon their iron status, haemoglobinopathies and inflammatory activity. Iron deficiency anaemia (n=132, anaemia of long duration (ACD, (n=97 and anaemia associated with chronic disease with iron deficiency (ACD Combi, (n=58. Microcytic Red cells, hypochromic red cells percentage and levels of haemoglobin in reticulocytes and matured RBCs were calculated. The accuracy of the parameters was analysed using receiver operating characteristic analyser to differentiate between the types of anaemia. OBSERVATIONS AND RESULTS There was no difference in parameters between the iron deficiency group or anaemia associated with chronic disease and iron deficiency. The hypochromic red cells percentage was the best parameter in differentiating anaemia of chronic disease with or without absolute iron deficiency with a sensitivity of 72.7% and a specificity of 70.4%. CONCLUSIONS The parameters of red cells and reticulocytes were of reasonably good indicators in differentiating the absolute iron deficiency anaemia with chronic disease.

A correction technique for the dispersive effects of mass lumping for transport problems

KAUST Repository

Guermond, Jean-Luc

2013-01-01

This paper addresses the well-known dispersion effect that mass lumping induces when solving transport-like equations. A simple anti-dispersion technique based on the lumped mass matrix is proposed. The method does not require any non-trivial matrix inversion and has the same anti-dispersive effects as the consistent mass matrix. A novel quasi-lumping technique for P2 finite elements is introduced. Higher-order extensions of the method are also discussed. © 2012 Elsevier B.V.

Identification of ecosystem parameters by SDE-modelling

DEFF Research Database (Denmark)

Stochastic differential equations (SDEs) for ecosystem modelling have attracted increasing attention during recent years. The modelling has mostly been through simulation experiments in order to analyse how system noise propagates through the ordinary differential equation formulation of ecosystem...... models. Estimation of parameters in SDEs is, however, possible by combining Kalman filter techniques and likelihood estimation. By modelling parameters as random walks it is possible to identify linear as well as non-linear interactions between ecosystem components. By formulating a simple linear SDE...

Hydrogen mixing analyses for a VVER containment.

Energy Technology Data Exchange (ETDEWEB)

Sienicki, J.J.; Kostka, P.; Techy, Z.

2002-02-25

Hydrogen combustion may represent a threat to containment integrity in a VVER-440/213 plant owing to the combination of high pressure and high temperature. A study has been carried out using the GASFLOW 2.1 three-dimensional CFD code to evaluate the hydrogen distribution in the containment during a beyond design basis accident. The VVER-440/213 containment input model consists of two 3D blocks connected via one-dimensional (1D) ducts. One 3D block contains the reactor building and the accident localization tower with the suppression pools. Another 3D block models the air traps. 1D ducts represent the check valves connecting the accident localization tower with the air traps. The VVER pressure suppression system, called ''bubbler condenser,'' was modeled as a distributed heat sink with water thermodynamic properties. This model accounts for the energy balance. However, it is not currently possible to model dynamic phenomena associated with the water pools (e.g., vent clearing, level change). The GASFLOW 2.1 calculation gave detailed results for the spatial distribution of thermal-hydraulic parameters and gas concentrations. The range and trend of the parameters are reasonable and valuable. There are particularly interesting circulation patterns around the steam generators, in the bubbler tower and other primary system compartments. In case of the bubbler tower, concentration and temperature contour plots show an inhomogeneous distribution along the height and width, changing during the accident. Hydrogen concentrations also vary within primary system compartments displaying lower as well as higher (up to 13-20% and higher) values in some nodes. Prediction of such concentration distributions was not previously possible with lumped parameter codes. GASFLOW 2.1 calculations were compared with CONTAIN 1.2 (lumped parameter code) results. Apart from the qualitatively similar trends, there are, for the time being, quantitative differences between the

Development of a PWR-W GOTHIC 3D model for containment accident analysis

International Nuclear Information System (INIS)

Bocanegra, Rafael; Jimenez, Gonzalo; Fernández-Cosials, Mikel Kevin

2016-01-01

Highlights: • The development of several 3D PWR containment models is described. • A Large Break LOCA is simulated. • The temperature and velocity fields are highly dependent on three-dimensional phenomena. • The pressure evolution is qualitatively similar in all models with small quantitative differences. - Abstract: The confinement of radioactive material in a nuclear power plant, including the discharge control and the release minimization, is a fundamental safety function to be ensured in a design basis accident (DBA). For plant licensing analysis, the containment is usually modeled with a lumped parameter approach. Inherent to the lumped parameter approach is the assumption that within each region the fluid is well mixed. However, the containment is a large building with a complex configuration and it is distributed in several compartments that avoid the well mixing of the fluid and could have three-dimensional effects that affect the thermal–hydraulic behavior. Therefore, the commonly used lumped parameter approach may not be enough to capture these effects. In order to study these assumptions, four generic PWR containment models have been developed for Mass and Energy (M&E) release analysis with GOTHIC 8.0 (QA) code, three of them being subdivided and the fourth one is a lumped parameter model. A Large Break LOCA is simulated in order to compare the thermal–hydraulic behavior of the different models. The results show a high dependence on the three-dimensional phenomena, especially the temperature and velocity distribution. In contrast, the pressure evolution is qualitatively similar in all models with small quantitative differences.

Modelling the heat dynamics of a building using stochastic differential equations

DEFF Research Database (Denmark)

Andersen, Klaus Kaae; Madsen, Henrik; Hansen, Lars Henrik

2000-01-01

estimation and model validation, while physical knowledge is used in forming the model structure. The suggested lumped parameter model is thus based on thermodynamics and formulated as a system of stochastic differential equations. Due to the continuous time formulation the parameters of the model...

Kinetic modelling of hydrocracking catalytic reactions by the single events theory; Modelisation cinetique des reactions catalytiques d`hydrocraquage par la theorie des evenements constitutifs

Energy Technology Data Exchange (ETDEWEB)

Schweitzer, J.M.

1998-11-23

Kinetic modelling of petroleum hydrocracking is particularly difficult given the complexity of the feedstocks. There are two distinct classes of kinetics models: lumped empirical models and detailed molecular models. The productivity of lumped empirical models is generally not very accurate, and the number of kinetic parameters increases rapidly with the number of lumps. A promising new methodology is the use of kinetic modelling based on the single events theory. Due to the molecular approach, a finite and limited number of kinetic parameters can describe the kinetic behaviour of the hydrocracking of heavy feedstock. The parameters are independent of the feedstock. However, the available analytical methods are not able to identify the products on the molecular level. This can be accounted for by means of an posteriori lamping technique, which incorporates the detailed knowledge of the elementary step network. Thus, the lumped kinetic parameters are directly calculated from the fundamental kinetic coefficients and the single event model is reduced to a re-lumped molecular model. Until now, the ability of the method to extrapolate to higher carbon numbers had not been demonstrated. In addition, no study had been published for three phase (gas-liquid-solid) systems and a complex feedstock. The objective of this work is to validate the `single events` method using a paraffinic feedstock. First of all, a series of experiments was conducted on a model compound (hexadecane) in order to estimate the fundamental kinetic parameters for acyclic molecules. To validate the single event approach, these estimated kinetic coefficients were used to simulate hydrocracking of a paraffinic mixture ranging from C11 to C18. The simulation results were then compared to the results obtained from the hydrocracking experiments. The comparison allowed to validate the model for acyclic molecules and to demonstrate that the model is applicable to compounds with higher carbon numbers. (author

Reduced order modeling and parameter identification of a building energy system model through an optimization routine

International Nuclear Information System (INIS)

Harish, V.S.K.V.; Kumar, Arun

2016-01-01

Highlights: • A BES model based on 1st principles is developed and solved numerically. • Parameters of lumped capacitance model are fitted using the proposed optimization routine. • Validations are showed for different types of building construction elements. • Step response excitations for outdoor air temperature and relative humidity are analyzed. - Abstract: Different control techniques together with intelligent building technology (Building Automation Systems) are used to improve energy efficiency of buildings. In almost all control projects, it is crucial to have building energy models with high computational efficiency in order to design and tune the controllers and simulate their performance. In this paper, a set of partial differential equations are formulated accounting for energy flow within the building space. These equations are then solved as conventional finite difference equations using Crank–Nicholson scheme. Such a model of a higher order is regarded as a benchmark model. An optimization algorithm has been developed, depicted through a flowchart, which minimizes the sum squared error between the step responses of the numerical and the optimal model. Optimal model of the construction element is nothing but a RC-network model with the values of Rs and Cs estimated using the non-linear time invariant constrained optimization routine. The model is validated with comparing the step responses with other two RC-network models whose parameter values are selected based on a certain criteria. Validations are showed for different types of building construction elements viz., low, medium and heavy thermal capacity elements. Simulation results show that the optimal model closely follow the step responses of the numerical model as compared to the responses of other two models.

RRAWFLOW: Rainfall-Response Aquifer and Watershed Flow Model (v1.15)

Science.gov (United States)

Long, Andrew J.

2015-01-01

The Rainfall-Response Aquifer and Watershed Flow Model (RRAWFLOW) is a lumped-parameter model that simulates streamflow, spring flow, groundwater level, or solute transport for a measurement point in response to a system input of precipitation, recharge, or solute injection. I introduce the first version of RRAWFLOW available for download and public use and describe additional options. The open-source code is written in the R language and is available at http://sd.water.usgs.gov/projects/RRAWFLOW/RRAWFLOW.html along with an example model of streamflow. RRAWFLOW includes a time-series process to estimate recharge from precipitation and simulates the response to recharge by convolution, i.e., the unit-hydrograph approach. Gamma functions are used for estimation of parametric impulse-response functions (IRFs); a combination of two gamma functions results in a double-peaked IRF. A spline fit to a set of control points is introduced as a new method for estimation of nonparametric IRFs. Several options are included to simulate time-variant systems. For many applications, lumped models simulate the system response with equal accuracy to that of distributed models, but moreover, the ease of model construction and calibration of lumped models makes them a good choice for many applications (e.g., estimating missing periods in a hydrologic record). RRAWFLOW provides professional hydrologists and students with an accessible and versatile tool for lumped-parameter modeling.

A correction technique for the dispersive effects of mass lumping for transport problems

KAUST Repository

Guermond, Jean-Luc; Pasquetti, Richard

2013-01-01

This paper addresses the well-known dispersion effect that mass lumping induces when solving transport-like equations. A simple anti-dispersion technique based on the lumped mass matrix is proposed. The method does not require any non-trivial matrix

Cross sections of the lumped fission products for the AMZ library

International Nuclear Information System (INIS)

Ono, S.; Corcueca, R.P.; Nascimento, J.A.

1985-01-01

The preparation of the lumped fission product cross section for the AMZ library is described. For this purpose 100 nuclides were selected. The cross sections for each nuclide were generated by the NJOY code with evaluated nuclear data from ENDF/B-V, complemented with ENDF/B-IV data. A comparison is performed between the data obtained and the lumped fission product cross section of JFS-II [pt

Mathematical modeling of CANDU-PHWR

Energy Technology Data Exchange (ETDEWEB)

Gaber, F.A.; Aly, R.A.; El-Shal, A.O. [Atomic Energy Authority, Cairo (Egypt)

2001-07-01

The paper deals with the transient studies of CANDU 600 pressurized Heavy Water Reactor (PHWR) system. This study involved mathematical modeling of CANDU PHWR major system components and the developments of software to study the thermodynamic performances. Modeling of CANDU-PHWR was based on lumped parameter technique.The integrated CANDU-PHWR model includes the neutronic, reactivity, fuel channel heat transfer, piping and the preheater type U-tube steam generator (PUTSG). The nuclear reactor power was modelled using the point kinetics equations with six groups of delayed neutrons and reactivity feed back due to the changes in fuel temperature and coolant temperature. The complex operation of the preheater type U-tube steam generator (PUTSG) is represented by a non-linear dynamic model using a state variable, moving boundary and lumped parameter techniques. The secondary side of the PUTSG model has six separate lumps including a preheater region, a lower boiling section, a mixing region, a riser, a chimmeny section, and a down-corner. The tube side of PUTSG has three main thermal zones. The PUTSG model is based on conservation of mass, energy and momentum relation-ships. The CANDU-PHWR integrated model are coded in FORTRAN language and solved by using a standard numerical technique. The adequacy of the model was tested by assessing the physical plausibility of the obtained results. (author)

Path lumping: An efficient algorithm to identify metastable path channels for conformational dynamics of multi-body systems

Science.gov (United States)

Meng, Luming; Sheong, Fu Kit; Zeng, Xiangze; Zhu, Lizhe; Huang, Xuhui

2017-07-01

Constructing Markov state models from large-scale molecular dynamics simulation trajectories is a promising approach to dissect the kinetic mechanisms of complex chemical and biological processes. Combined with transition path theory, Markov state models can be applied to identify all pathways connecting any conformational states of interest. However, the identified pathways can be too complex to comprehend, especially for multi-body processes where numerous parallel pathways with comparable flux probability often coexist. Here, we have developed a path lumping method to group these parallel pathways into metastable path channels for analysis. We define the similarity between two pathways as the intercrossing flux between them and then apply the spectral clustering algorithm to lump these pathways into groups. We demonstrate the power of our method by applying it to two systems: a 2D-potential consisting of four metastable energy channels and the hydrophobic collapse process of two hydrophobic molecules. In both cases, our algorithm successfully reveals the metastable path channels. We expect this path lumping algorithm to be a promising tool for revealing unprecedented insights into the kinetic mechanisms of complex multi-body processes.

Hydrogen Analyses in the EPR

International Nuclear Information System (INIS)

Worapittayaporn, S.; Eyink, J.; Movahed, M.

2008-01-01

In severe accidents with core melting large amounts of hydrogen may be released into the containment. The EPR provides a combustible gas control system to prevent hydrogen combustion modes with the potential to challenge the containment integrity due to excessive pressure and temperature loads. This paper outlines the approach for the verification of the effectiveness and efficiency of this system. Specifically, the justification is a multi-step approach. It involves the deployment of integral codes, lumped parameter containment codes and CFD codes and the use of the sigma criterion, which provides the link to the broad experimental data base for flame acceleration (FA) and deflagration to detonation transition (DDT). The procedure is illustrated with an example. The performed analyses show that hydrogen combustion at any time does not lead to pressure or temperature loads that threaten the containment integrity of the EPR. (authors)

Experimental Verification of Guided-Wave Lumped Circuits Using Waveguide Metamaterials

Science.gov (United States)

Li, Yue; Zhang, Zhijun

2018-04-01

Through the construction and characterization in microwave frequencies, we experimentally demonstrate our recently developed theory of waveguide lumped circuits, i.e., waveguide metatronics [Sci. Adv. 2, e1501790 (2016), 10.1126/sciadv.1501790], as a method to design subwavelength-scaled analog circuits. In the paradigm of waveguide metatronics, numbers of lumped inductors and capacitors are easily integrated functionally inside the waveguide, which is an irreplaceable transmission line in millimeter-wave and terahertz systems with the advantages of low radiation loss and low crosstalk. An example of multiple-ordered metatronic filters with layered structures is fabricated utilizing the technique of substrate integrated waveguides, which can be easily constructed by the printed-circuit-board process. The materials used in the construction are also typical microwave materials with positive permittivity, low loss, and negligible dispersion, imitating the plasmonic materials with negative permittivity in the optical domain. The results verify the theory of waveguide metatronics, which provides an efficient platform of functional lumped circuit design for guided-wave processing.

Application of flexibility model in modeling of flow boiling heat transfer

International Nuclear Information System (INIS)

Peng Jinfeng; Zhao Fuyu

2009-01-01

The mathematical modeling and computer simulation have been widely used in the analysis of system's dynamic characteristics, and often useful for system control. One of the popular methods for this purpose is the lumped parameter method. For flow boiling heat transfer system, the traditional lumped parameter modeling method has a problem that the heat transfer coefficients change suddenly at the boundary of coolant phase change. It can cause error. In this paper, an idea of flexibility model is developed to deal with the boundary problem and to improve the model of flow boiling heat transfer. The segments of coolant phase change's boundary are identified, and the membership functions which are derived from Fuzzy Mathematics are used to derive approximate expressions of heat transfer coefficient in those regions. The continuity of heat transfer coefficient can be described by those expressions. The membership functions are derived from mathematical analysis and transformation. The result shows that this idea is feasible and the conclusion is practicable.

Robust estimation of hydrological model parameters

Directory of Open Access Journals (Sweden)

A. Bárdossy

2008-11-01

Full Text Available The estimation of hydrological model parameters is a challenging task. With increasing capacity of computational power several complex optimization algorithms have emerged, but none of the algorithms gives a unique and very best parameter vector. The parameters of fitted hydrological models depend upon the input data. The quality of input data cannot be assured as there may be measurement errors for both input and state variables. In this study a methodology has been developed to find a set of robust parameter vectors for a hydrological model. To see the effect of observational error on parameters, stochastically generated synthetic measurement errors were applied to observed discharge and temperature data. With this modified data, the model was calibrated and the effect of measurement errors on parameters was analysed. It was found that the measurement errors have a significant effect on the best performing parameter vector. The erroneous data led to very different optimal parameter vectors. To overcome this problem and to find a set of robust parameter vectors, a geometrical approach based on Tukey's half space depth was used. The depth of the set of N randomly generated parameters was calculated with respect to the set with the best model performance (Nash-Sutclife efficiency was used for this study for each parameter vector. Based on the depth of parameter vectors, one can find a set of robust parameter vectors. The results show that the parameters chosen according to the above criteria have low sensitivity and perform well when transfered to a different time period. The method is demonstrated on the upper Neckar catchment in Germany. The conceptual HBV model was used for this study.

Lumped Parameter Models for Predicting Nitrogen Transport in Lower Coastal Plain Watersheds

Science.gov (United States)

Devendra M. Amatya; George M. Chescheir; Glen P. Fernandez; R. Wayne Skaggs; F. Birgand; J.W. Gilliam

2003-01-01

hl recent years physically based comprehensive disfributed watershed scale hydrologic/water quality models have been developed and applied 10 evaluate cumulative effects of land arld water management practices on receiving waters, Although fhesc complex physically based models are capable of simulating the impacts ofthese changes in large watersheds, they are often...

New equivalent lumped electrical circuit for piezoelectric transformers.

Science.gov (United States)

Gonnard, Paul; Schmitt, P M; Brissaud, Michel

2006-04-01

A new equivalent circuit is proposed for a contour-vibration-mode piezoelectric transformer (PT). It is shown that the usual lumped equivalent circuit derived from the conventional Mason approach is not accurate. The proposed circuit, built on experimental measurements, makes an explicit difference between the elastic energies stored respectively on the primary and secondary parts. The experimental and theoretical resonance frequencies with the secondary in open or short circuit are in good agreement as well as the output "voltage-current" characteristic and the optimum efficiency working point. This circuit can be extended to various PT configurations and appears to be a useful tool for modeling electronic devices that integrate piezoelectric transformers.

24 CFR 570.513 - Lump sum drawdown for financing of property rehabilitation activities.

Science.gov (United States)

2010-04-01

... DEVELOPMENT BLOCK GRANTS Grant Administration § 570.513 Lump sum drawdown for financing of property... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lump sum drawdown for financing of property rehabilitation activities. 570.513 Section 570.513 Housing and Urban Development Regulations...

Multi-time-step ahead daily and hourly intermittent reservoir inflow prediction by artificial intelligent techniques using lumped and distributed data

Science.gov (United States)

Jothiprakash, V.; Magar, R. B.

2012-07-01

SummaryIn this study, artificial intelligent (AI) techniques such as artificial neural network (ANN), Adaptive neuro-fuzzy inference system (ANFIS) and Linear genetic programming (LGP) are used to predict daily and hourly multi-time-step ahead intermittent reservoir inflow. To illustrate the applicability of AI techniques, intermittent Koyna river watershed in Maharashtra, India is chosen as a case study. Based on the observed daily and hourly rainfall and reservoir inflow various types of time-series, cause-effect and combined models are developed with lumped and distributed input data. Further, the model performance was evaluated using various performance criteria. From the results, it is found that the performances of LGP models are found to be superior to ANN and ANFIS models especially in predicting the peak inflows for both daily and hourly time-step. A detailed comparison of the overall performance indicated that the combined input model (combination of rainfall and inflow) performed better in both lumped and distributed input data modelling. It was observed that the lumped input data models performed slightly better because; apart from reducing the noise in the data, the better techniques and their training approach, appropriate selection of network architecture, required inputs, and also training-testing ratios of the data set. The slight poor performance of distributed data is due to large variations and lesser number of observed values.

Sensitivity Analyses for Cross-Coupled Parameters in Automotive Powertrain Optimization

Directory of Open Access Journals (Sweden)

Pongpun Othaganont

2014-06-01

Full Text Available When vehicle manufacturers are developing new hybrid and electric vehicles, modeling and simulation are frequently used to predict the performance of the new vehicles from an early stage in the product lifecycle. Typically, models are used to predict the range, performance and energy consumption of their future planned production vehicle; they also allow the designer to optimize a vehicle’s configuration. Another use for the models is in performing sensitivity analysis, which helps us understand which parameters have the most influence on model predictions and real-world behaviors. There are various techniques for sensitivity analysis, some are numerical, but the greatest insights are obtained analytically with sensitivity defined in terms of partial derivatives. Existing methods in the literature give us a useful, quantified measure of parameter sensitivity, a first-order effect, but they do not consider second-order effects. Second-order effects could give us additional insights: for example, a first order analysis might tell us that a limiting factor is the efficiency of the vehicle’s prime-mover; our new second order analysis will tell us how quickly the efficiency of the powertrain will become of greater significance. In this paper, we develop a method based on formal optimization mathematics for rapid second-order sensitivity analyses and illustrate these through a case study on a C-segment electric vehicle.

A weighted least-squares lump correction algorithm for transmission-corrected gamma-ray nondestructive assay

International Nuclear Information System (INIS)

Prettyman, T.H.; Sprinkle, J.K. Jr.; Sheppard, G.A.

1993-01-01

With transmission-corrected gamma-ray nondestructive assay instruments such as the Segmented Gamma Scanner (SGS) and the Tomographic Gamma Scanner (TGS) that is currently under development at Los Alamos National Laboratory, the amount of gamma-ray emitting material can be underestimated for samples in which the emitting material consists of particles or lumps of highly attenuating material. This problem is encountered in the assay of uranium and plutonium-bearing samples. To correct for this source of bias, we have developed a least-squares algorithm that uses transmission-corrected assay results for several emitted energies and a weighting function to account for statistical uncertainties in the assay results. The variation of effective lump size in the fitted model is parameterized; this allows the correction to be performed for a wide range of lump-size distributions. It may be possible to use the reduced chi-squared value obtained in the fit to identify samples in which assay assumptions have been violated. We found that the algorithm significantly reduced bias in simulated assays and improved SGS assay results for plutonium-bearing samples. Further testing will be conducted with the TGS, which is expected to be less susceptible than the SGS to systematic source of bias

A distributed lumped active all-pass network configuration.

Science.gov (United States)

Huelsman, L. P.; Raghunath, S.

1972-01-01

In this correspondence a new and interesting distributed lumped active network configuration that realizes an all-pass network function is described. A design chart for determining the values of the network elements is included.

On a sparse pressure-flow rate condensation of rigid circulation models

Science.gov (United States)

Schiavazzi, D. E.; Hsia, T. Y.; Marsden, A. L.

2015-01-01

Cardiovascular simulation has shown potential value in clinical decision-making, providing a framework to assess changes in hemodynamics produced by physiological and surgical alterations. State-of-the-art predictions are provided by deterministic multiscale numerical approaches coupling 3D finite element Navier Stokes simulations to lumped parameter circulation models governed by ODEs. Development of next-generation stochastic multiscale models whose parameters can be learned from available clinical data under uncertainty constitutes a research challenge made more difficult by the high computational cost typically associated with the solution of these models. We present a methodology for constructing reduced representations that condense the behavior of 3D anatomical models using outlet pressure-flow polynomial surrogates, based on multiscale model solutions spanning several heart cycles. Relevance vector machine regression is compared with maximum likelihood estimation, showing that sparse pressure/flow rate approximations offer superior performance in producing working surrogate models to be included in lumped circulation networks. Sensitivities of outlets flow rates are also quantified through a Sobol’ decomposition of their total variance encoded in the orthogonal polynomial expansion. Finally, we show that augmented lumped parameter models including the proposed surrogates accurately reproduce the response of multiscale models they were derived from. In particular, results are presented for models of the coronary circulation with closed loop boundary conditions and the abdominal aorta with open loop boundary conditions. PMID:26671219

Modelling and Multi-Variable Control of Refrigeration Systems

DEFF Research Database (Denmark)

Larsen, Lars Finn Slot; Holm, J. R.

2003-01-01

In this paper a dynamic model of a 1:1 refrigeration system is presented. The main modelling effort has been concentrated on a lumped parameter model of a shell and tube condenser. The model has shown good resemblance with experimental data from a test rig, regarding as well the static as the dyn......In this paper a dynamic model of a 1:1 refrigeration system is presented. The main modelling effort has been concentrated on a lumped parameter model of a shell and tube condenser. The model has shown good resemblance with experimental data from a test rig, regarding as well the static...... as the dynamic behavior. Based on this model the effects of the cross couplings has been examined. The influence of the cross couplings on the achievable control performance has been investigated. A MIMO controller is designed and the performance is compared with the control performance achieved by using...

Modelling of FCC (Fluid Catalytic Cracking) risers with six lumps; Modelo de elevadores de Unidades de Craqueamento Catalitico com cinetica de seis classes

Energy Technology Data Exchange (ETDEWEB)

Baldessar, Fabio; Negrao, Cezar O. Ribeiro; Palu, Claudia [Centro Federal de Educacao Tecnologica do Parana (CEFET-PR), Curitiba, PR (Brazil)

2004-07-01

The current work presents a mathematical model of an ascendant flow vertical reactor (riser) of a Fluid Catalytic Cracking Unit. The two-phase flow (gas-solid) and the cracking reactions are admitted one-dimensional and steady state. Mass, momentum and energy conservation equations are considered for each phase (solid and gas). A six-lump kinetic model is employed to evaluate gasoil, gasoline, GLP, fuel gas, light cycle oil and coke fractions. The model results are compared to experimental values from a pilot plant and to another model found in the literature. The results are in good agreement, showing the model has great potential. (author)

The frequency of malignancy in breast lumps on fnac in females under 35 years of age

International Nuclear Information System (INIS)

Iqbal, M.; Iqbal, M.

2014-01-01

Breast carcinoma is one of the common malignancies in females and its incidence is increasing in younger age. Diagnosis of carcinoma breast includes clinical evaluation, imaging and pathology. Fine Needle Aspiration Cytology is the first line pathological investigation in the diagnosis with excellent results. Objective: To determine the frequency of malignancy in breast lumps on FNAC in females under 35 years of age. Descriptive cross sectional study. Setting:Department of pathology Fatima Jinnah Medical College (FJMC), Lahore. Duration: Six months from 20th July, 2011 till 20th January, 2012.Methods: 150 female patients 35 years of age or less, presenting to the OPD and Indoor of Sir Ganga Ram Hospital Lahore, an affiliated hospital of FJMC Lahore, with breast lumps were included in the study. Demographic features and consent of the patients were noted. FNAC of the patients was performed as per advice of the consultant. Diagnosis of malignant cases was further confirmed on histology.Results: Out of all, 124 lumps (82.7%) were benign and 26 lumps (17.3%) were malignant. Amongst the benign lumps, 77(62.1%) were fibroadenomas, 28(22.6%) were fibrocystic changes, 08(06.5%) were inflammatory lesions, 07(05.6%) showed pyogenic abscess and 04 lumps (03.2%) were galactoceles. Amongst the malignant lumps, 22(84.6%) were ductal carcinoma, 02(07.7%) colloid carcinoma and 02(07.7%) were malignant phylloides. Conclusions: The frequency of malignancy in breast lumps in Pakistan is significantly high in females under 35 years of age. Appropriate measures are needed for prevention and early diagnosis and treatment in young females. (author)

CLINICO PATHOLOGICAL STUDY OF BENIGN BREAST LUMP – A HOSPITAL BASED STUDY

Directory of Open Access Journals (Sweden)

Anindita

2016-03-01

Full Text Available BACKGROUND Despite the fact that in majority of cases the initial symptom of benign breast disease is a lump, which can be easily detected by the patient herself by self-examination they generally present at a very late stage and this poses a great difficulty in their management. Early and appropriate diagnosis of breast disease is of utmost importance. AIM The aim of the study was to find out the relative frequency and commonest site of occurrence of benign breast disorder and their relationship with age, parity, menstrual cycle, and socio-economic status and also to find out the accuracy of investigative procedures in their diagnosis. DESIGN This is a cross sectional, interventional. Hospital based study. MATERIALS AND METHOD This study was done in 58 female patients in the age group 10 yrs. to 55 yrs. presenting with clinically benign breast lumps randomly chosen from outpatient department and indoor wards of The Calcutta Medical Research Institute, Kolkata. After taking an accurate history and proper clinical examination these patients were sequentially studied by radiological methods (Ultrasonography and mammography, fine needle aspiration cytology (FNAC and histopathology of removed specimen. Patients were enquired about their age, chief complaints, menstrual history, and use of oral pill, marital status, parity, lactation and socioeconomic status. RESULTS 79% of the benign breast lumps were found to be between 10–35 years, Fibro adenoma being the commonest one (41.38% and fibrocystic disease the second most common (29.31%. Breast lump were more common among unmarried and nulliparous females (48.27%, commonest site being upper and outer quadrant (38.8%. 69% patients were associated with an abnormal menstrual status. 76% of the cases were accurately diagnosed by clinical examination, 70% by mammography, 88% by FNAC and 84% by ultrasonography. CONCLUSION This clinicopathological study of benign breast lump is a small endeavour on our part

Biomass viability: An experimental study and the development of an empirical mathematical model for submerged membrane bioreactor.

Science.gov (United States)

Zuthi, M F R; Ngo, H H; Guo, W S; Nghiem, L D; Hai, F I; Xia, S Q; Zhang, Z Q; Li, J X

2015-08-01

This study investigates the influence of key biomass parameters on specific oxygen uptake rate (SOUR) in a sponge submerged membrane bioreactor (SSMBR) to develop mathematical models of biomass viability. Extra-cellular polymeric substances (EPS) were considered as a lumped parameter of bound EPS (bEPS) and soluble microbial products (SMP). Statistical analyses of experimental results indicate that the bEPS, SMP, mixed liquor suspended solids and volatile suspended solids (MLSS and MLVSS) have functional relationships with SOUR and their relative influence on SOUR was in the order of EPS>bEPS>SMP>MLVSS/MLSS. Based on correlations among biomass parameters and SOUR, two independent empirical models of biomass viability were developed. The models were validated using results of the SSMBR. However, further validation of the models for different operating conditions is suggested. Copyright © 2015 Elsevier Ltd. All rights reserved.

The role of CFD computer analyses in hydrogen safety management

International Nuclear Information System (INIS)

Komen, E.M.J; Visser, D.C; Roelofs, F.; Te Lintelo, J.G.T

2014-01-01

The risks of hydrogen release and combustion during a severe accident in a light water reactor have attracted considerable attention after the Fukushima accident in Japan. Reliable computer analyses are needed for the optimal design of hydrogen mitigation systems, like e.g. passive autocatalytic recombiners (PARs), and for the assessment of the associated residual risk of hydrogen combustion. Traditionally, so-called Lumped Parameter (LP) computer codes are being used for these purposes. In the last decade, significant progress has been made in the development, validation, and application of more detailed, three-dimensional Computational Fluid Dynamics (CFD) simulations for hydrogen safety analyses. The objective of the current paper is to address the following questions: - When are CFD computer analyses needed complementary to the traditional LP code analyses for hydrogen safety management? - What is the validation status of the CFD computer code for hydrogen distribution, mitigation, and combustion analyses? - Can CFD computer analyses nowadays be executed in practical and reliable way for full scale containments? The validation status and reliability of CFD code simulations will be illustrated by validation analyses performed for experiments executed in the PANDA, THAI, and ENACCEF facilities. (authors)

Electric circuit coupling of a slotted semi-analytical model for induction motors based on harmonic modeling

NARCIS (Netherlands)

Sprangers, R.L.J.; Paulides, J.J.H.; Gysen, B.L.J.; Waarma, J.; Lomonova, E.A.

2014-01-01

The use of empirically determined coefficients to include the effects of leakage and fringing flux is a large drawback of traditional induction motor (IM) models, such as lumped parameter, magnetic equivalent circuit and anisotropic layer models. As an alternative, Finite Element Analysis (FEA) is

APPROACH TO THE DIAGNOSIS OF A BREAST LUMP

African Journals Online (AJOL)

breast cancer in any woman, irrespective of age.1,2 Fortunately, the vast majority of breast lumps are ... malignant breast lesions can be diagnosed in this way. When all aspects ... ultrasonography is the preferred modality for women under 35 ...

Systematic reduction of complex tropospheric chemical mechanisms, Part II: Lumping using a time-scale based approach

Directory of Open Access Journals (Sweden)

L. E. Whitehouse

2004-01-01

Full Text Available This paper presents a formal method of species lumping that can be applied automatically to intermediate compounds within detailed and complex tropospheric chemical reaction schemes. The method is based on grouping species with reference to their chemical lifetimes and reactivity structures. A method for determining the forward and reverse transformations between individual and lumped compounds is developed. Preliminary application to the Leeds Master Chemical Mechanism (MCMv2.0 has led to the removal of 734 species and 1777 reactions from the scheme, with minimal degradation of accuracy across a wide range of test trajectories relevant to polluted tropospheric conditions. The lumped groups are seen to relate to groups of peroxy acyl nitrates, nitrates, carbonates, oxepins, substituted phenols, oxeacids and peracids with similar lifetimes and reaction rates with OH. In combination with other reduction techniques, such as sensitivity analysis and the application of the quasi-steady state approximation (QSSA, a reduced mechanism has been developed that contains 35% of the number of species and 40% of the number of reactions compared to the full mechanism. This has led to a speed up of a factor of 8 in terms of computer calculation time within box model simulations.

Probabilistic and Nonprobabilistic Sensitivity Analyses of Uncertain Parameters

Directory of Open Access Journals (Sweden)

Sheng-En Fang

2014-01-01

Full Text Available Parameter sensitivity analyses have been widely applied to industrial problems for evaluating parameter significance, effects on responses, uncertainty influence, and so forth. In the interest of simple implementation and computational efficiency, this study has developed two sensitivity analysis methods corresponding to the situations with or without sufficient probability information. The probabilistic method is established with the aid of the stochastic response surface and the mathematical derivation proves that the coefficients of first-order items embody the parameter main effects on the response. Simultaneously, a nonprobabilistic interval analysis based method is brought forward for the circumstance when the parameter probability distributions are unknown. The two methods have been verified against a numerical beam example with their accuracy compared to that of a traditional variance-based method. The analysis results have demonstrated the reliability and accuracy of the developed methods. And their suitability for different situations has also been discussed.

Identifying the connective strength between model parameters and performance criteria

Directory of Open Access Journals (Sweden)

B. Guse

2017-11-01

is found for low- and mid-flow conditions. Moreover, the RT analyses emphasise the benefit of an individual analysis of the three components of KGE and of the FDC segments. Furthermore, the RT analyses highlight under which conditions these performance criteria provide insights into precise parameter identification. Our results show that separate performance criteria are required to identify dominant parameters on low- and mid-flow conditions, whilst the number of required performance criteria for high flows increases with increasing process complexity in the catchment. Overall, the analysis of the connective strength between model parameters and performance criteria using RTs contribute to a more realistic handling of parameters and performance criteria in hydrological modelling.

VIIP: Central Nervous System (CNS) Modeling

Science.gov (United States)

Vera, Jerry; Mulugeta, Lealem; Nelson, Emily; Raykin, Julia; Feola, Andrew; Gleason, Rudy; Samuels, Brian; Ethier, C. Ross; Myers, Jerry

2015-01-01

Current long-duration missions to the International Space Station and future exploration-class missions beyond low-Earth orbit expose astronauts to increased risk of Visual Impairment and Intracranial Pressure (VIIP) syndrome. It has been hypothesized that the headward shift of cerebrospinal fluid (CSF) and blood in microgravity may cause significant elevation of intracranial pressure (ICP), which in turn may then induce VIIP syndrome through interaction with various biomechanical pathways. However, there is insufficient evidence to confirm this hypothesis. In this light, we are developing lumped-parameter models of fluid transport in the central nervous system (CNS) as a means to simulate the influence of microgravity on ICP. The CNS models will also be used in concert with the lumped parameter and finite element models of the eye described in the related IWS works submitted by Nelson et al., Feola et al. and Ethier et al.

Mixed lump-kink and rogue wave-kink solutions for a (3 + 1) -dimensional B-type Kadomtsev-Petviashvili equation in fluid mechanics

Science.gov (United States)

Hu, Cong-Cong; Tian, Bo; Wu, Xiao-Yu; Yuan, Yu-Qiang; Du, Zhong

2018-02-01

Under investigation is a (3 + 1) -dimensional B-type Kadomtsev-Petviashvili equation, which describes the weakly dispersive waves in a fluid. Via the Hirota method and symbolic computation, we obtain the mixed lump-kink and mixed rogue wave-kink solutions. Through the mixed lump-kink solutions, we observe three different phenomena between a lump and one kink. For the fusion phenomenon, a lump and a kink are merged with the lump's energy transferring into the kink gradually, until the lump merges into the kink completely. Fission phenomenon displays that a lump separates from a kink. The last phenomenon shows that a lump travels together with a kink with their amplitudes unchanged. In addition, we graphically study the interaction between a rogue wave and a pair of the kinks. It can be observed that the rogue wave arises from one kink and disappears into the other kink. At certain time, the amplitude of the rogue wave reaches the maximum.

How often do sensitivity analyses for economic parameters change cost-utility analysis conclusions?

Science.gov (United States)

Schackman, Bruce R; Gold, Heather Taffet; Stone, Patricia W; Neumann, Peter J

2004-01-01

There is limited evidence about the extent to which sensitivity analysis has been used in the cost-effectiveness literature. Sensitivity analyses for health-related QOL (HR-QOL), cost and discount rate economic parameters are of particular interest because they measure the effects of methodological and estimation uncertainties. To investigate the use of sensitivity analyses in the pharmaceutical cost-utility literature in order to test whether a change in economic parameters could result in a different conclusion regarding the cost effectiveness of the intervention analysed. Cost-utility analyses of pharmaceuticals identified in a prior comprehensive audit (70 articles) were reviewed and further audited. For each base case for which sensitivity analyses were reported (n = 122), up to two sensitivity analyses for HR-QOL (n = 133), cost (n = 99), and discount rate (n = 128) were examined. Article mentions of thresholds for acceptable cost-utility ratios were recorded (total 36). Cost-utility ratios were denominated in US dollars for the year reported in each of the original articles in order to determine whether a different conclusion would have been indicated at the time the article was published. Quality ratings from the original audit for articles where sensitivity analysis results crossed the cost-utility ratio threshold above the base-case result were compared with those that did not. The most frequently mentioned cost-utility thresholds were $US20,000/QALY, $US50,000/QALY, and $US100,000/QALY. The proportions of sensitivity analyses reporting quantitative results that crossed the threshold above the base-case results (or where the sensitivity analysis result was dominated) were 31% for HR-QOL sensitivity analyses, 20% for cost-sensitivity analyses, and 15% for discount-rate sensitivity analyses. Almost half of the discount-rate sensitivity analyses did not report quantitative results. Articles that reported sensitivity analyses where results crossed the cost

The mobilisation model and parameter sensitivity

International Nuclear Information System (INIS)

Blok, B.M.

1993-12-01

In the PRObabillistic Safety Assessment (PROSA) of radioactive waste in a salt repository one of the nuclide release scenario's is the subrosion scenario. A new subrosion model SUBRECN has been developed. In this model the combined effect of a depth-dependent subrosion, glass dissolution, and salt rise has been taken into account. The subrosion model SUBRECN and the implementation of this model in the German computer program EMOS4 is presented. A new computer program PANTER is derived from EMOS4. PANTER models releases of radionuclides via subrosion from a disposal site in a salt pillar into the biosphere. For uncertainty and sensitivity analyses the new subrosion model Latin Hypercube Sampling has been used for determine the different values for the uncertain parameters. The influence of the uncertainty in the parameters on the dose calculations has been investigated by the following sensitivity techniques: Spearman Rank Correlation Coefficients, Partial Rank Correlation Coefficients, Standardised Rank Regression Coefficients, and the Smirnov Test. (orig./HP)

Fire Detection Tradeoffs as a Function of Vehicle Parameters

Science.gov (United States)

Urban, David L.; Dietrich, Daniel L.; Brooker, John E.; Meyer, Marit E.; Ruff, Gary A.

2016-01-01

Fire survivability depends on the detection of and response to a fire before it has produced an unacceptable environment in the vehicle. This detection time is the result of interplay between the fire burning and growth rates; the vehicle size; the detection system design; the transport time to the detector (controlled by the level of mixing in the vehicle); and the rate at which the life support system filters the atmosphere, potentially removing the detected species or particles. Given the large differences in critical vehicle parameters (volume, mixing rate and filtration rate) the detection approach that works for a large vehicle (e.g. the ISS) may not be the best choice for a smaller crew capsule. This paper examines the impact of vehicle size and environmental control and life support system parameters on the detectability of fires in comparison to the hazard they present. A lumped element model was developed that considers smoke, heat, and toxic product release rates in comparison to mixing and filtration rates in the vehicle. Recent work has quantified the production rate of smoke and several hazardous species from overheated spacecraft polymers. These results are used as the input data set in the lumped element model in combination with the transport behavior of major toxic products released by overheating spacecraft materials to evaluate the necessary alarm thresholds to enable appropriate response to the fire hazard.

Fission and fusion interaction phenomena of mixed lump kink solutions for a generalized (3+1)-dimensional B-type Kadomtsev-Petviashvili equation

Science.gov (United States)

Liu, Yaqing; Wen, Xiaoyong

2018-05-01

In this paper, a generalized (3+1)-dimensional B-type Kadomtsev-Petviashvili (gBKP) equation is investigated by using the Hirota’s bilinear method. With the aid of symbolic computation, some new lump, mixed lump kink and periodic lump solutions are derived. Based on the derived solutions, some novel interaction phenomena like the fission and fusion interactions between one lump soliton and one kink soliton, the fission and fusion interactions between one lump soliton and a pair of kink solitons and the interactions between two periodic lump solitons are discussed graphically. Results might be helpful for understanding the propagation of the shallow water wave.

Sensitivity and uncertainty analyses for performance assessment modeling

International Nuclear Information System (INIS)

Doctor, P.G.

1988-08-01

Sensitivity and uncertainty analyses methods for computer models are being applied in performance assessment modeling in the geologic high level radioactive waste repository program. The models used in performance assessment tend to be complex physical/chemical models with large numbers of input variables. There are two basic approaches to sensitivity and uncertainty analyses: deterministic and statistical. The deterministic approach to sensitivity analysis involves numerical calculation or employs the adjoint form of a partial differential equation to compute partial derivatives; the uncertainty analysis is based on Taylor series expansions of the input variables propagated through the model to compute means and variances of the output variable. The statistical approach to sensitivity analysis involves a response surface approximation to the model with the sensitivity coefficients calculated from the response surface parameters; the uncertainty analysis is based on simulation. The methods each have strengths and weaknesses. 44 refs

Prediction of Seismic Slope Displacements by Dynamic Stick-Slip Analyses

International Nuclear Information System (INIS)

Ausilio, Ernesto; Costanzo, Antonio; Silvestri, Francesco; Tropeano, Giuseppe

2008-01-01

A good-working balance between simplicity and reliability in assessing seismic slope stability is represented by displacement-based methods, in which the effects of deformability and ductility can be either decoupled or coupled in the dynamic analyses. In this paper, a 1D lumped mass ''stick-slip'' model is developed, accounting for soil heterogeneity and non-linear behaviour, with a base sliding mechanism at a potential rupture surface. The results of the preliminary calibration show a good agreement with frequency-domain site response analysis in no-slip conditions. The comparison with rigid sliding block analyses and with the decoupled approach proves that the stick-slip procedure can result increasingly unconservative for soft soils and deep sliding depths

Numerical reproduction of hemodynamics change by acupuncture on Taichong (LR-3 based on the lumped-parameter approximation model of the systemic arteries

Directory of Open Access Journals (Sweden)

Atsushi Shirai

2015-09-01

Conclusion: The present model has a potential to emulate hemodynamic change by acupuncture therapy by incorporating physiological correlation of stimulation of an acupoint and regulation of parameters that affect the hemodynamics.

Lumped thermal capacitance analysis of transient heat conduction ...

African Journals Online (AJOL)

Lumped thermal capacitance analysis has been undertaken to investigate the transient temperature variations, associated induced thermal stress distributions, and the structural integrity of Ghana Research Reactor-1 (GHAR R-1) vessel after 15 years of operation. The beltline configuration of the cylindrical vessel of the ...

14C chronology of the oldest Scandinavian church in use. An AMS/PIXE study of lime lump carbonate in the mortar

International Nuclear Information System (INIS)

Lindroos, Alf; Ranta, Heikki; 14C Dating Laboratory, Department of Physics and Astronomy, University of Aarhus (Denmark))" data-affiliation=" (AMS 14C Dating Laboratory, Department of Physics and Astronomy, University of Aarhus (Denmark))" >Heinemeier, Jan; Lill, Jan-Olof

2014-01-01

Mortar dating was applied to newly revealed, original mortar in the church of Dalby in Scania, southern Sweden which is considered to be the oldest still standing church in Scandinavia. Small white lime lumps were sampled by chipping from the supporting pillars in the interior of the church. Special emphasis was in sampling lime lumps because the church is situated in the Scania limestone area and aggregate limestone contamination was anticipated in the bulk mortars. Earlier studies have, however, shown that lime lumps do not contain aggregate material but only possible limestone rests from incomplete calcination. The sampled material was prepared for radiocarbon AMS dating. The carbonate in the lime lumps was hydrolyzed according to the sequential leaching technique developed for the Århus 14 C laboratory in Denmark. Prior to the hydrolysis the lime lumps were examined for dead-carbon contamination using a stereo microscope and cathodoluminescence. The lime lumps displayed heterogeneous carbonate luminescence. This is, however, common and it was not considered a problem because carbonate growth in changing pH/Eh conditions often leads to changing luminescence colors. Two lumps had little dead carbon contamination and an early second millennium 14 C signature. One lump, however, seemed to be heavily contaminated with dead carbon. Since the sample passed the microscopic screening, the leftovers of the lump was subjected to PIXE analysis and compared with the other two lumps. The well-defined, early 2nd millennium 14 C age of the lime lumps of this particular church is an important contribution to the discussion on stone church chronology in Scandinavia

airGR: a suite of lumped hydrological models in an R-package

Science.gov (United States)

Coron, Laurent; Perrin, Charles; Delaigue, Olivier; Andréassian, Vazken; Thirel, Guillaume

2016-04-01

Lumped hydrological models are useful and convenient tools for research, engineering and educational purposes. They propose catchment-scale representations of the precipitation-discharge relationship. Thanks to their limited data requirements, they can be easily implemented and run. With such models, it is possible to simulate a number of hydrological key processes over the catchment with limited structural and parametric complexity, typically evapotranspiration, runoff, underground losses, etc. The Hydrology Group at Irstea (Antony) has been developing a suite of rainfall-runoff models over the past 30 years with the main objectives of designing models as efficient as possible in terms of streamflow simulation, applicable to a wide range of catchments and having low data requirements. This resulted in a suite of models running at different time steps (from hourly to annual) applicable for various issues including water balance estimation, forecasting, simulation of impacts and scenario testing. Recently, Irstea has developed an easy-to-use R-package (R Core Team, 2015), called airGR, to make these models widely available. It includes: - the water balance annual GR1A (Mouehli et al., 2006), - the monthly GR2M (Mouehli, 2003) models, - three versions of the daily model, namely GR4J (Perrin et al., 2003), GR5J (Le Moine, 2008) and GR6J (Pushpalatha et al., 2011), - the hourly GR4H model (Mathevet, 2005), - a degree-day snow module CemaNeige (Valéry et al., 2014). The airGR package has been designed to facilitate the use by non-expert users and allow the addition of evaluation criteria, models or calibration algorithms selected by the end-user. Each model core is coded in FORTRAN to ensure low computational time. The other package functions (i.e. mainly the calibration algorithm and the efficiency criteria) are coded in R. The package is already used for educational purposes. The presentation will detail the main functionalities of the package and present a case

Role of cytological grading in the management of breast lump

International Nuclear Information System (INIS)

Mehmood, A.; Ahmed, M.; Jamal, S.

2003-01-01

Objective: To evaluate the fine needle aspiration (FNA) smears of the breast lumps using the cytological evaluation system (C1 to C5) as practiced in the National Breast Screening Programme in the UK. Results: A total of 75 patients of lump breast were included in the project. The age range was 13-75 years with a peak incidence in the 3rd decade. There were 70 (93.3%) females and 5 (6.6%) male cases. Of the total 75 cases, 7 were designated C1, 45 C2, 5 C3, 7 C4 and 11 C5. In surgical biopsies, all the 45 cases designated as C2 proved to be benign with fibroadenoma and fibrocystic change as predominant lesions. All 11 designated C5 proved to be malignant; whereas, of the 5 cases labeled as C3, 4 were benign and one was malignant and out of seven C4 cases, 5 came out as malignant and 2 proved benign. Conclusion: the fine needle aspiration of lump breast has a sensitivity of 94.1%, specificity of 96.0% and accuracy of 95.5%. The C1-C5 grading system is practical, flexible, and gives room for expression of opinion by cytopathologist and easily interpreted by clincians. (author)

Dynamics of lumps and dark-dark solitons in the multi-component long-wave-short-wave resonance interaction system

Science.gov (United States)

Rao, Jiguang; Porsezian, Kuppuswamy; He, Jingsong; Kanna, Thambithurai

2018-01-01

General semi-rational solutions of an integrable multi-component (2+1)-dimensional long-wave-short-wave resonance interaction system comprising multiple short waves and a single long wave are obtained by employing the bilinear method. These solutions describe the interactions between various types of solutions, including line rogue waves, lumps, breathers and dark solitons. We only focus on the dynamical behaviours of the interactions between lumps and dark solitons in this paper. Our detailed study reveals two different types of excitation phenomena: fusion and fission. It is shown that the fundamental (simplest) semi-rational solutions can exhibit fission of a dark soliton into a lump and a dark soliton or fusion of one lump and one dark soliton into a dark soliton. The non-fundamental semi-rational solutions are further classified into three subclasses: higher-order, multi- and mixed-type semi-rational solutions. The higher-order semi-rational solutions show the process of annihilation (production) of two or more lumps into (from) one dark soliton. The multi-semi-rational solutions describe N(N≥2) lumps annihilating into or producing from N-dark solitons. The mixed-type semi-rational solutions are a hybrid of higher-order semi-rational solutions and multi-semi-rational solutions. For the mixed-type semi-rational solutions, we demonstrate an interesting dynamical behaviour that is characterized by partial suppression or creation of lumps from the dark solitons.

Dynamics of lumps and dark-dark solitons in the multi-component long-wave-short-wave resonance interaction system.

Science.gov (United States)

Rao, Jiguang; Porsezian, Kuppuswamy; He, Jingsong; Kanna, Thambithurai

2018-01-01

General semi-rational solutions of an integrable multi-component (2+1)-dimensional long-wave-short-wave resonance interaction system comprising multiple short waves and a single long wave are obtained by employing the bilinear method. These solutions describe the interactions between various types of solutions, including line rogue waves, lumps, breathers and dark solitons. We only focus on the dynamical behaviours of the interactions between lumps and dark solitons in this paper. Our detailed study reveals two different types of excitation phenomena: fusion and fission. It is shown that the fundamental (simplest) semi-rational solutions can exhibit fission of a dark soliton into a lump and a dark soliton or fusion of one lump and one dark soliton into a dark soliton. The non-fundamental semi-rational solutions are further classified into three subclasses: higher-order, multi- and mixed-type semi-rational solutions. The higher-order semi-rational solutions show the process of annihilation (production) of two or more lumps into (from) one dark soliton. The multi-semi-rational solutions describe N ( N ≥2) lumps annihilating into or producing from N -dark solitons. The mixed-type semi-rational solutions are a hybrid of higher-order semi-rational solutions and multi-semi-rational solutions. For the mixed-type semi-rational solutions, we demonstrate an interesting dynamical behaviour that is characterized by partial suppression or creation of lumps from the dark solitons.

A fast semi-analytical model for the slotted structure of induction motors

NARCIS (Netherlands)

Sprangers, R.L.J.; Paulides, J.J.H.; Gysen, B.L.J.; Lomonova, E.A.

A fast, semi-analytical model for induction motors (IMs) is presented. In comparison to traditional analytical models for IMs, such as lumped parameter, magnetic equivalent circuit and anisotropic layer models, the presented model calculates a continuous distribution of the magnetic flux density in

Predicting cycle time distributions for integrated processing workstations : an aggregate modeling approach

NARCIS (Netherlands)

Veeger, C.P.L.; Etman, L.F.P.; Lefeber, A.A.J.; Adan, I.J.B.F.; Herk, van J.; Rooda, J.E.

2011-01-01

To predict cycle time distributions of integrated processing workstations, detailed simulation models are almost exclusively used; these models require considerable development and maintenance effort. As an alternative, we propose an aggregate model that is a lumped-parameter representation of the

Model-Based Recursive Partitioning for Subgroup Analyses.

Science.gov (United States)

Seibold, Heidi; Zeileis, Achim; Hothorn, Torsten

2016-05-01

The identification of patient subgroups with differential treatment effects is the first step towards individualised treatments. A current draft guideline by the EMA discusses potentials and problems in subgroup analyses and formulated challenges to the development of appropriate statistical procedures for the data-driven identification of patient subgroups. We introduce model-based recursive partitioning as a procedure for the automated detection of patient subgroups that are identifiable by predictive factors. The method starts with a model for the overall treatment effect as defined for the primary analysis in the study protocol and uses measures for detecting parameter instabilities in this treatment effect. The procedure produces a segmented model with differential treatment parameters corresponding to each patient subgroup. The subgroups are linked to predictive factors by means of a decision tree. The method is applied to the search for subgroups of patients suffering from amyotrophic lateral sclerosis that differ with respect to their Riluzole treatment effect, the only currently approved drug for this disease.

VIPRE modeling of VVER-1000 reactor core for DNB analyses

Energy Technology Data Exchange (ETDEWEB)

Sung, Y.; Nguyen, Q. [Westinghouse Electric Corporation, Pittsburgh, PA (United States); Cizek, J. [Nuclear Research Institute, Prague, (Czech Republic)

1995-09-01

Based on the one-pass modeling approach, the hot channels and the VVER-1000 reactor core can be modeled in 30 channels for DNB analyses using the VIPRE-01/MOD02 (VIPRE) code (VIPRE is owned by Electric Power Research Institute, Palo Alto, California). The VIPRE one-pass model does not compromise any accuracy in the hot channel local fluid conditions. Extensive qualifications include sensitivity studies of radial noding and crossflow parameters and comparisons with the results from THINC and CALOPEA subchannel codes. The qualifications confirm that the VIPRE code with the Westinghouse modeling method provides good computational performance and accuracy for VVER-1000 DNB analyses.

Management of breast lumps in Maiduguri, Nigeria

Directory of Open Access Journals (Sweden)

Ali Nuhu

2014-01-01

Full Text Available Background: Reported changes in the demography, modes of presentation and histological variants of tumors of the breast have been published in developed and some developing countries. Although benign lesions have persistently accounted for most breast tumors, the incidence of malignant breast lesion in young women in sub-Saharan Africa has been disturbingly high. We reviewed the demographics, pattern and management of breast lumps excised at University of Maiduguri Teaching Hospital (UMTH over a 6 year period. Patients and Methods: A retrospective study of patients with breast lumps at UMTH was carried out between January 2005 and December 2010. Details of their bio-data, clinical, and histopathology details were analyzed using descriptive statistics. Results: A total of 913 patients, comprising 887 females (97.2% and 26 males (2.8% were reviewed. The mean age was 33.1 ± 14.6 years (range: 12-80 years and the mean duration of symptoms was 8 ± 2.14 months (range: 2-23 months. 359 (39.3% were malignant and 577 (63.2% were benign. The mean ages of women and men with invasive carcinomas of the breast were 45.58 ± 13.22 and 49.75 ± 18.28 years, respectively. The mean age of women with benign breast disease was 28.4 ± 10.0 for fibrocystic disease and 21.8 ± 5.31 years for fibroadenoma. Mode of presentations included ulcers (8.7%, axillary lymph node enlargement (30.0%, nipple discharge (13.0% and breast pain (21.7%. The most common histological diagnoses were carcinoma of the breast, N = 340 (37.2%, fibroadenoma, N = 276 (30.2% and fibrocystic disease, N = 199 (21.8%. The least common pathology was tuberculosis of the breast, N = 6; (0.7%. Conclusion: Though benign diseases are still more common, a high percentage of breast lumps in Maiduguri are due to malignant disease and this is frequent in younger women.

29 CFR Appendix C to Part 4022 - Lump Sum Interest Rates for Private-Sector Payments

Science.gov (United States)

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Lump Sum Interest Rates for Private-Sector Payments C Appendix C to Part 4022 Labor Regulations Relating to Labor (Continued) PENSION BENEFIT GUARANTY... Appendix C to Part 4022—Lump Sum Interest Rates for Private-Sector Payments [In using this table: (1) For...

The Numerical Welding Simulation - Developments and Validation of Simplified and Bead Lumping Methods

International Nuclear Information System (INIS)

Baup, Olivier

2001-01-01

The aim of this work was to study the TIG multipass welding process on stainless steel, by means of numerical methods and then to work out simplified and bead lumping methods in order to reduce adjusting and realisation times of these calculations. A simulation was used as reference for the validation of these methods; after the presentation of the test series having led to the option choices of this calculation (2D generalised plane strains, elastoplastic model with an isotropic hardening, hardening restoration due to high temperatures), various simplifications were tried on a plate geometry. These simplifications related various modelling points with a correct plastic flow representation in the plate. The use of a reduced number of thermal fields characterising the bead deposit and a low number of tensile curves allow to obtain interesting results, decreasing significantly the Computing times. In addition various lumping bead methods have been studied and concerning both the shape and the thermic of the macro-deposits. The macro-deposit shapes studied are in 'L', or in layer or they represent two beads one on top of the other. Among these three methods, only those using a few number of lumping beads gave bad results since thermo-mechanical history was deeply modified near and inside the weld. Thereafter, simplified methods have been applied to a tubular geometry. On this new geometry, experimental measurements were made during welding, which allow a validation of the reference calculation. Simplified and reference calculations gave approximately the same stress fields as found on plate geometry. Finally, in the last part of this document a procedure for automatic data setting permitting to reduce significantly the calculation phase preparation is presented. It has been applied to the calculation of thick pipe welding in 90 beads; the results are compared with a simplified simulation realised by Framatome and with experimental measurements. A bead by

Parameter estimation of component reliability models in PSA model of Krsko NPP

International Nuclear Information System (INIS)

Jordan Cizelj, R.; Vrbanic, I.

2001-01-01

In the paper, the uncertainty analysis of component reliability models for independent failures is shown. The present approach for parameter estimation of component reliability models in NPP Krsko is presented. Mathematical approaches for different types of uncertainty analyses are introduced and used in accordance with some predisposed requirements. Results of the uncertainty analyses are shown in an example for time-related components. As the most appropriate uncertainty analysis proved the Bayesian estimation with the numerical estimation of a posterior, which can be approximated with some appropriate probability distribution, in this paper with lognormal distribution.(author)

Approach to the diagnosis of a breast lump

African Journals Online (AJOL)

Generally, the older the woman, the greater the degree of suspicion and the more aggressive the ... When patients present with a history of a breast lump, the first crucial step is to ... A past history of a breast biopsy showing atypical hyperplasia, a family history of ... ultrasonography is the preferred modality for women under ...

Axillary silicone lymphadenopathy presenting with a lump and altered sensation in the breast: a case report

Directory of Open Access Journals (Sweden)

Adams Simon T

2009-03-01

Full Text Available Abstract Introduction Silicone lymphadenopathy is a rare but recognised complication of procedures involving the use of silicone. It has a poorly understood mechanism but is thought to occur following the transportation of silicone particles from silicone-containing prostheses to lymph nodes by macrophages. Case presentation We report of a case involving a 35-year-old woman who presented to the breast clinic with a breast lump and altered sensation below her left nipple 5 years after bilateral cosmetic breast augmentations. A small lump was detected inferior to the nipple but clinical examination and initial ultrasound investigation showed both implants to be intact. However, mammography and magnetic resonance imaging of both breasts revealed both intracapsular and extracapsular rupture of the left breast prosthesis. The patient went on to develop a flu-like illness and tender lumps in the left axilla and right mastoid regions. An excision biopsy of the left axillary lesion and replacement of the ruptured implant was performed. Subsequent histological analysis showed that the axillary lump was a lymph node containing large amounts of silicone. Conclusion The exclusion of malignancy remains the priority when dealing with lumps in the breast or axilla. Silicone lymphadenopathy should however be considered as a differential diagnosis in patients in whom silicone prostheses are present.

Monte Carlo modeling and analyses of YALINA-booster subcritical assembly part 1: analytical models and main neutronics parameters

International Nuclear Information System (INIS)

Talamo, A.; Gohar, M. Y. A.; Nuclear Engineering Division

2008-01-01

This study was carried out to model and analyze the YALINA-Booster facility, of the Joint Institute for Power and Nuclear Research of Belarus, with the long term objective of advancing the utilization of accelerator driven systems for the incineration of nuclear waste. The YALINA-Booster facility is a subcritical assembly, driven by an external neutron source, which has been constructed to study the neutron physics and to develop and refine methodologies to control the operation of accelerator driven systems. The external neutron source consists of Californium-252 spontaneous fission neutrons, 2.45 MeV neutrons from Deuterium-Deuterium reactions, or 14.1 MeV neutrons from Deuterium-Tritium reactions. In the latter two cases a deuteron beam is used to generate the neutrons. This study is a part of the collaborative activity between Argonne National Laboratory (ANL) of USA and the Joint Institute for Power and Nuclear Research of Belarus. In addition, the International Atomic Energy Agency (IAEA) has a coordinated research project benchmarking and comparing the results of different numerical codes with the experimental data available from the YALINA-Booster facility and ANL has a leading role coordinating the IAEA activity. The YALINA-Booster facility has been modeled according to the benchmark specifications defined for the IAEA activity without any geometrical homogenization using the Monte Carlo codes MONK and MCNP/MCNPX/MCB. The MONK model perfectly matches the MCNP one. The computational analyses have been extended through the MCB code, which is an extension of the MCNP code with burnup capability because of its additional feature for analyzing source driven multiplying assemblies. The main neutronics parameters of the YALINA-Booster facility were calculated using these computer codes with different nuclear data libraries based on ENDF/B-VI-0, -6, JEF-2.2, and JEF-3.1

Monte Carlo modeling and analyses of YALINA-booster subcritical assembly part 1: analytical models and main neutronics parameters.

Energy Technology Data Exchange (ETDEWEB)

Talamo, A.; Gohar, M. Y. A.; Nuclear Engineering Division

2008-09-11

This study was carried out to model and analyze the YALINA-Booster facility, of the Joint Institute for Power and Nuclear Research of Belarus, with the long term objective of advancing the utilization of accelerator driven systems for the incineration of nuclear waste. The YALINA-Booster facility is a subcritical assembly, driven by an external neutron source, which has been constructed to study the neutron physics and to develop and refine methodologies to control the operation of accelerator driven systems. The external neutron source consists of Californium-252 spontaneous fission neutrons, 2.45 MeV neutrons from Deuterium-Deuterium reactions, or 14.1 MeV neutrons from Deuterium-Tritium reactions. In the latter two cases a deuteron beam is used to generate the neutrons. This study is a part of the collaborative activity between Argonne National Laboratory (ANL) of USA and the Joint Institute for Power and Nuclear Research of Belarus. In addition, the International Atomic Energy Agency (IAEA) has a coordinated research project benchmarking and comparing the results of different numerical codes with the experimental data available from the YALINA-Booster facility and ANL has a leading role coordinating the IAEA activity. The YALINA-Booster facility has been modeled according to the benchmark specifications defined for the IAEA activity without any geometrical homogenization using the Monte Carlo codes MONK and MCNP/MCNPX/MCB. The MONK model perfectly matches the MCNP one. The computational analyses have been extended through the MCB code, which is an extension of the MCNP code with burnup capability because of its additional feature for analyzing source driven multiplying assemblies. The main neutronics parameters of the YALINA-Booster facility were calculated using these computer codes with different nuclear data libraries based on ENDF/B-VI-0, -6, JEF-2.2, and JEF-3.1.

{sup 14}C chronology of the oldest Scandinavian church in use. An AMS/PIXE study of lime lump carbonate in the mortar

Energy Technology Data Exchange (ETDEWEB)

Lindroos, Alf, E-mail: alf.lindroos@abo.fi [Geology and Mineralogy, Department of Natural Sciences, Åbo Akademi University (Finland); Art History, Faculty of Art, Åbo Akademi University (Finland); Ranta, Heikki [Diocese of Lund, Church of Sweden (Sweden); Heinemeier, Jan [AMS " 1" 4C Dating Laboratory, Department of Physics and Astronomy, University of Aarhus (Denmark); Lill, Jan-Olof [Accelerator Laboratory, Turku PET Centre, Åbo Akademi University (Finland)

2014-07-15

Mortar dating was applied to newly revealed, original mortar in the church of Dalby in Scania, southern Sweden which is considered to be the oldest still standing church in Scandinavia. Small white lime lumps were sampled by chipping from the supporting pillars in the interior of the church. Special emphasis was in sampling lime lumps because the church is situated in the Scania limestone area and aggregate limestone contamination was anticipated in the bulk mortars. Earlier studies have, however, shown that lime lumps do not contain aggregate material but only possible limestone rests from incomplete calcination. The sampled material was prepared for radiocarbon AMS dating. The carbonate in the lime lumps was hydrolyzed according to the sequential leaching technique developed for the Århus {sup 14}C laboratory in Denmark. Prior to the hydrolysis the lime lumps were examined for dead-carbon contamination using a stereo microscope and cathodoluminescence. The lime lumps displayed heterogeneous carbonate luminescence. This is, however, common and it was not considered a problem because carbonate growth in changing pH/Eh conditions often leads to changing luminescence colors. Two lumps had little dead carbon contamination and an early second millennium {sup 14}C signature. One lump, however, seemed to be heavily contaminated with dead carbon. Since the sample passed the microscopic screening, the leftovers of the lump was subjected to PIXE analysis and compared with the other two lumps. The well-defined, early 2nd millennium {sup 14}C age of the lime lumps of this particular church is an important contribution to the discussion on stone church chronology in Scandinavia.

Analysis, scale modeling, and full-scale test of a railcar and spent-nuclear-fuel shipping cask in a high-velocity impact against a rigid barrier

International Nuclear Information System (INIS)

Huerta, M.

1981-06-01

This report describes the mathematical analysis, the physical scale modeling, and a full-scale crash test of a railcar spent-nuclear-fuel shipping system. The mathematical analysis utilized a lumped-parameter model to predict the structural response of the railcar and the shipping cask. The physical scale modeling analysis consisted of two crash tests that used 1/8-scale models to assess railcar and shipping cask damage. The full-scale crash test, conducted with retired railcar equipment, was carefully monitored with onboard instrumentation and high-speed photography. Results of the mathematical and scale modeling analyses are compared with the full-scale test. 29 figures

Modelling of intermittent microwave convective drying: parameter sensitivity

Directory of Open Access Journals (Sweden)

Zhang Zhijun

2017-06-01

Full Text Available The reliability of the predictions of a mathematical model is a prerequisite to its utilization. A multiphase porous media model of intermittent microwave convective drying is developed based on the literature. The model considers the liquid water, gas and solid matrix inside of food. The model is simulated by COMSOL software. Its sensitivity parameter is analysed by changing the parameter values by ±20%, with the exception of several parameters. The sensitivity analysis of the process of the microwave power level shows that each parameter: ambient temperature, effective gas diffusivity, and evaporation rate constant, has significant effects on the process. However, the surface mass, heat transfer coefficient, relative and intrinsic permeability of the gas, and capillary diffusivity of water do not have a considerable effect. The evaporation rate constant has minimal parameter sensitivity with a ±20% value change, until it is changed 10-fold. In all results, the temperature and vapour pressure curves show the same trends as the moisture content curve. However, the water saturation at the medium surface and in the centre show different results. Vapour transfer is the major mass transfer phenomenon that affects the drying process.

Parallelized FDTD simulation for flat-plate bounded wave EMP simulator with lumped terminator

International Nuclear Information System (INIS)

Zhu Xiangqin; Chen Weiqing; Chen Zaigao; Cai Libing; Wang Jianguo

2013-01-01

A parallelized finite-difference time-domain(FDTD) method for simulating the bounded wave electromagnetic pulse (EMP) simulator with lumped terminator and parallel plate is presented. The effects of several model-parameters on the simulator to the fields in the working volume are simulated and analyzed. The results show that if the width of the lower PEC plate is(or is bigger than)1.5 times that of the upper plate of working volume, the projection length of front transitional section does not have a significant effect on the rise-times of electric fields at the points near the front transitional section, and the rise-times of electric fields at the points near the working volume center decrease as the projection length increases, but the decrement of rise-time decreases. The rise-times of E z at all points also decrease as the lower PEC plate's width increases, but the decrements of rise-time decreases. If the projection length of the front transitional section is fixed, the good results can not be obtained by increasing or decreasing the height of the simulator only, however, which has an optimal value. (authors)

29 CFR 4044.75 - Other lump sum benefits.

Science.gov (United States)

2010-07-01

... sum benefits. The value of a lump sum benefit which is not covered under § 4044.73 or § 4044.74 is equal to— (a) The value under the qualifying bid, if an insurer provides the benefit; or (b) The present value of the benefit as of the date of distribution, determined using reasonable actuarial assumptions...

Leaks, Lumps, and Lines: Stigma and Women's Bodies

Science.gov (United States)

Chrisler, Joan C.

2011-01-01

Women's bodies have often been positioned in art and popular culture as monstrous or defiled and women's bodily products (e.g., menstrual fluid, breast milk) as disgusting. This framing has led to the stigmatization of aspects of women's bodies (e.g., leaking fluids, lumps of fat, and lines in the skin that indicate aging), especially those…

Modelling asymmetry in the peripheral auditory system of the lizard

DEFF Research Database (Denmark)

Zhang, Lei; Hallam, John; Christensen-Dalsgaard, Jakob

2008-01-01

The ears of lizards are highly directional. The directionality is generated by strong acoustical coupling of the eardrums. A simple lumped-parameter model of the ear followed by binaural comparisons has been shown to perform successful phonotaxis in robot implementations. However, such a model...

Cytological and Pathological Correlation of FNAC in Assessing Breast Lumps and Axillary Lymph Node Swellings in a Public Sector Hospital in India

Directory of Open Access Journals (Sweden)

Vasu Reddy Challa

2013-01-01

Full Text Available Background. Breast lumps have varied pathology, and there are different techniques to prove the diagnosis. The aim of the present study is to analyze the role of fine needle aspiration cytology (FNAC of the breast lesions at our center. Methods. We had retrospectively analysed 854 patients who underwent FNAC for primary breast lumps and 190 patients who underwent FNAC for an axillary lymph node in the year 2010. Results. Of 854 patients, histological correlation was available in 723 patients. The analysis was done for 812 patients as medical records were not available for 42 patients. FNAC was false negative in seven cases; 2 cases of phyllodes were reported as fibroadenoma, and 5 cases of carcinoma were diagnosed as atypical hyperplasia. The sensitivity, specificity, and false negative value of FNAC in diagnosing breast lumps were 99% (715/723, 100%, and 1%, respectively. Of 190 patients for whom FNAC was performed for axilla, 170 had proven to have axillary lymph node metastases, and the rest had reactive hyperplasia or inflammatory cells. Conclusions. FNAC is rapid, accurate, outpatient based, and less complicated procedure and helps in diagnosis of breast cancer, benign diseases, and axillary involvement in experienced hands with less chance of false results.

Application of a user-friendly comprehensive circulatory model for estimation of hemodynamic and ventricular variables

NARCIS (Netherlands)

Ferrari, G.; Kozarski, M.; Gu, Y. J.; De Lazzari, C.; Di Molfetta, A.; Palko, K. J.; Zielinski, K.; Gorczynska, K.; Darowski, M.; Rakhorst, G.

2008-01-01

Purpose: Application of a comprehensive, user-friendly, digital computer circulatory model to estimate hemodynamic and ventricular variables. Methods: The closed-loop lumped parameter circulatory model represents the circulation at the level of large vessels. A variable elastance model reproduces

Beyond the SCS-CN method: A theoretical framework for spatially lumped rainfall-runoff response

Science.gov (United States)

Bartlett, M. S.; Parolari, A. J.; McDonnell, J. J.; Porporato, A.

2016-06-01

Since its introduction in 1954, the Soil Conservation Service curve number (SCS-CN) method has become the standard tool, in practice, for estimating an event-based rainfall-runoff response. However, because of its empirical origins, the SCS-CN method is restricted to certain geographic regions and land use types. Moreover, it does not describe the spatial variability of runoff. To move beyond these limitations, we present a new theoretical framework for spatially lumped, event-based rainfall-runoff modeling. In this framework, we describe the spatially lumped runoff model as a point description of runoff that is upscaled to a watershed area based on probability distributions that are representative of watershed heterogeneities. The framework accommodates different runoff concepts and distributions of heterogeneities, and in doing so, it provides an implicit spatial description of runoff variability. Heterogeneity in storage capacity and soil moisture are the basis for upscaling a point runoff response and linking ecohydrological processes to runoff modeling. For the framework, we consider two different runoff responses for fractions of the watershed area: "prethreshold" and "threshold-excess" runoff. These occur before and after infiltration exceeds a storage capacity threshold. Our application of the framework results in a new model (called SCS-CNx) that extends the SCS-CN method with the prethreshold and threshold-excess runoff mechanisms and an implicit spatial description of runoff. We show proof of concept in four forested watersheds and further that the resulting model may better represent geographic regions and site types that previously have been beyond the scope of the traditional SCS-CN method.

From conservation laws to port-Hamiltonian representations of distributed-parameter systems

NARCIS (Netherlands)

Maschke, B.M.; van der Schaft, Arjan; Piztek, P.

Abstract: In this paper it is shown how the port-Hamiltonian formulation of distributed-parameter systems is closely related to the general thermodynamic framework of systems of conservation laws and closure equations. The situation turns out to be similar to the lumped-parameter case where the

A Grey Box Model for the Hydraulics in a Creek

DEFF Research Database (Denmark)

Jonsdottir, Harpa; Jacobsen, Judith L.; Madsen, Henrik

1998-01-01

The Saint-Venant equation of mass balance is used to derive a stochastics lumped model, describing the dynamics of a cross-sectional area in a river. The unknown parameters of the model are estimated by combining the physical equation with a set of data, a method known as grey box modelling...

A 3D Lumped Thermal Network Model for Long-term Load Profiles Analysis in High Power IGBT Modules

DEFF Research Database (Denmark)

Bahman, Amir Sajjad; Ma, Ke; Ghimire, Pramod

2016-01-01

)-based simulation is another method which is often used to analyze the steady-state thermal distribution of IGBT modules, but it is not possible to be used for long-term analysis of load profiles of power converter, which is needed for reliability assessments and better thermal design. This paper proposes a novel...... enables both accurate and fast temperature estimation of high power IGBT modules in the real loading conditions of the converter; meanwhile the critical details of the thermal dynamics and thermal distribution are also maintained. The proposed thermal model is verified by both FEM simulation......The conventional RC lumped thermal networks are widely used to estimate the temperature of power devices, but they are lack of accuracy in addressing detailed thermal behaviors/couplings in different locations and layers of the high power IGBT modules. On the other hand, Finite Element (FE...

Modelling of cardiovascular system: development of a hybrid (numerical-physical) model.

Science.gov (United States)

Ferrari, G; Kozarski, M; De Lazzari, C; Górczyńska, K; Mimmo, R; Guaragno, M; Tosti, G; Darowski, M

2003-12-01

Physical models of the circulation are used for research, training and for testing of implantable active and passive circulatory prosthetic and assistance devices. However, in comparison with numerical models, they are rigid and expensive. To overcome these limitations, we have developed a model of the circulation based on the merging of a lumped parameter physical model into a numerical one (producing therefore a hybrid). The physical model is limited to the barest essentials and, in this application, developed to test the principle, it is a windkessel representing the systemic arterial tree. The lumped parameters numerical model was developed in LabVIEW environment and represents pulmonary and systemic circulation (except the systemic arterial tree). Based on the equivalence between hydraulic and electrical circuits, this prototype was developed connecting the numerical model to an electrical circuit--the physical model. This specific solution is valid mainly educationally but permits the development of software and the verification of preliminary results without using cumbersome hydraulic circuits. The interfaces between numerical and electrical circuits are set up by a voltage controlled current generator and a voltage controlled voltage generator. The behavior of the model is analyzed based on the ventricular pressure-volume loops and on the time course of arterial and ventricular pressures and flow in different circulatory conditions. The model can represent hemodynamic relationships in different ventricular and circulatory conditions.

Bond Graph Model of Cerebral Circulation: Toward Clinically Feasible Systemic Blood Flow Simulations

Science.gov (United States)

Safaei, Soroush; Blanco, Pablo J.; Müller, Lucas O.; Hellevik, Leif R.; Hunter, Peter J.

2018-01-01

We propose a detailed CellML model of the human cerebral circulation that runs faster than real time on a desktop computer and is designed for use in clinical settings when the speed of response is important. A lumped parameter mathematical model, which is based on a one-dimensional formulation of the flow of an incompressible fluid in distensible vessels, is constructed using a bond graph formulation to ensure mass conservation and energy conservation. The model includes arterial vessels with geometric and anatomical data based on the ADAN circulation model. The peripheral beds are represented by lumped parameter compartments. We compare the hemodynamics predicted by the bond graph formulation of the cerebral circulation with that given by a classical one-dimensional Navier-Stokes model working on top of the whole-body ADAN model. Outputs from the bond graph model, including the pressure and flow signatures and blood volumes, are compared with physiological data. PMID:29551979

A wave propagation model of blood flow in large vessels using an approximate velocity profile function

NARCIS (Netherlands)

Bessems, D.; Rutten, M.C.M.; Vosse, van de F.N.

2007-01-01

Lumped-parameter models (zero-dimensional) and wave-propagation models (one-dimensional) for pressure and flow in large vessels, as well as fully three-dimensional fluid–structure interaction models for pressure and velocity, can contribute valuably to answering physiological and patho-physiological

Bridging the gap between measurements and modelling: a cardiovascular functional avatar.

Science.gov (United States)

Casas, Belén; Lantz, Jonas; Viola, Federica; Cedersund, Gunnar; Bolger, Ann F; Carlhäll, Carl-Johan; Karlsson, Matts; Ebbers, Tino

2017-07-24

Lumped parameter models of the cardiovascular system have the potential to assist researchers and clinicians to better understand cardiovascular function. The value of such models increases when they are subject specific. However, most approaches to personalize lumped parameter models have thus far required invasive measurements or fall short of being subject specific due to a lack of the necessary clinical data. Here, we propose an approach to personalize parameters in a model of the heart and the systemic circulation using exclusively non-invasive measurements. The personalized model is created using flow data from four-dimensional magnetic resonance imaging and cuff pressure measurements in the brachial artery. We term this personalized model the cardiovascular avatar. In our proof-of-concept study, we evaluated the capability of the avatar to reproduce pressures and flows in a group of eight healthy subjects. Both quantitatively and qualitatively, the model-based results agreed well with the pressure and flow measurements obtained in vivo for each subject. This non-invasive and personalized approach can synthesize medical data into clinically relevant indicators of cardiovascular function, and estimate hemodynamic variables that cannot be assessed directly from clinical measurements.

Study on vertical seismic response model of BWR-type reactor building

International Nuclear Information System (INIS)

Konno, T.; Motohashi, S.; Izumi, M.; Iizuka, S.

1993-01-01

A study on advanced seismic design for LWR has been carried out by the Nuclear Power Engineering Corporation (NUPEC), under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan. As a part of the study, it has been investigated to construct an accurate analytical model of reactor buildings for a seismic response analysis, which can reasonably represent dynamic characteristics of the building. In Japan, vibration models of reactor buildings for horizontal ground motion have been studied and examined through many simulation analyses for forced vibration tests and earthquake observations of actual buildings. And now it is possible to establish a reliable horizontal vibration model on the basis of multi-lumped mass and spring model. However, vertical vibration models have not been so much studied as horizontal models, due to less observed data for vertical motions. In this paper, the vertical seismic response models of a BWR-type reactor building including soil-structure interaction effect are numerically studied, by comparing the dynamic characteristics of (1) three dimensional finite element model, (2) multi-stick lumped mass model with a flexible base-mat, (3) multi-stick lumped mass model with a rigid base-mat and (4) single-stick lumped mass model. In particular, the BWR-type reactor building has the long span truss roof which is considered to be one of the critical members to vertical excitation. The modelings of the roof trusses are also studied

Aggressive angiomyxoma presenting with huge abdominal lump: A case report

Science.gov (United States)

Kumar, Sanjeev; Agrawal, Nikhil; Khanna, Rahul; Khanna, AK

2008-01-01

Agressive angiomyxoma is a rare mesenchymal neoplasm. It mainly presents in females. We here present a case of angiomyxoma presenting as huge abdominal lump along with gluteal swelling. Case note is described along with brief review of literature. PMID:18755035

Material model for non-linear finite element analyses of large concrete structures

NARCIS (Netherlands)

Engen, Morten; Hendriks, M.A.N.; Øverli, Jan Arve; Åldstedt, Erik; Beushausen, H.

2016-01-01

A fully triaxial material model for concrete was implemented in a commercial finite element code. The only required input parameter was the cylinder compressive strength. The material model was suitable for non-linear finite element analyses of large concrete structures. The importance of including

Incidence data for breast cancer among Yemeni female patients with palpable breast lumps.

Science.gov (United States)

Alsanabani, Jamila Ali; Gilan, Waleed; Saadi, Azzan Al

2015-01-01

To estimate the incidence of breast cancer in Yemeni female patients presenting with a breast mass. This retrospective study was carried out with 595 female patients with palpable breast lumps, attending to Alkuwait university hospital, Sana'a, Yemen. Triple assessment, including breast examination, mammography and biopsy (FNAC, core needle, or excision), for all patients were performed. The incidences of benign and malignant lesions was calculated. Some 160 (26.9%) of 595 patients had malignancies; 213 (35.8%) were fibroadenomas; 12 (2.0%) were fibrocystic change; 143 (24.03%) were inflammatory lesions (including mastitis and ductectasia); 62 (10.4%) were simple cysts, while 5 (0.8%) were phyllodes tumors. The mean age of patients with malignant lumps was 44.3 years. Among Yemeni female patients with palpable breast lumps, the rate of breast cancer is high, with occurrence at an earlier age than in Western countries. Improving breast cancer awareness programs and increasing breast cancer screening centers inb different areas of Yemen are needed to establish early diagnosis and offer early and optimal treatment.

Development and validation of a tokamak skin effect transformer model

International Nuclear Information System (INIS)

Romero, J.A.; Moret, J.-M.; Coda, S.; Felici, F.; Garrido, I.

2012-01-01

A lumped parameter, state space model for a tokamak transformer including the slow flux penetration in the plasma (skin effect transformer model) is presented. The model does not require detailed or explicit information about plasma profiles or geometry. Instead, this information is lumped in system variables, parameters and inputs. The model has an exact mathematical structure built from energy and flux conservation theorems, predicting the evolution and non-linear interaction of plasma current and internal inductance as functions of the primary coil currents, plasma resistance, non-inductive current drive and the loop voltage at a specific location inside the plasma (equilibrium loop voltage). Loop voltage profile in the plasma is substituted by a three-point discretization, and ordinary differential equations are used to predict the equilibrium loop voltage as a function of the boundary and resistive loop voltages. This provides a model for equilibrium loop voltage evolution, which is reminiscent of the skin effect. The order and parameters of this differential equation are determined empirically using system identification techniques. Fast plasma current modulation experiments with random binary signals have been conducted in the TCV tokamak to generate the required data for the analysis. Plasma current was modulated under ohmic conditions between 200 and 300 kA with 30 ms rise time, several times faster than its time constant L/R ≈ 200 ms. A second-order linear differential equation for equilibrium loop voltage is sufficient to describe the plasma current and internal inductance modulation with 70% and 38% fit parameters, respectively. The model explains the most salient features of the plasma current transients, such as the inverse correlation between plasma current ramp rates and internal inductance changes, without requiring detailed or explicit information about resistivity profiles. This proves that a lumped parameter modelling approach can be used to

Primary Breast Tuberculosis Presenting as a Lump: A Rare Modern ...

African Journals Online (AJOL)

mammary area. A 25. year.old female, presented with a lump in the breast and infra.mammary area. She was having off and on fever without any other complaints. There was no positive family history. Primary breast tuberculosis was diagnosed on fine ...

Hybrid Soft Soil Tire Model (HSSTM). Part 1: Tire Material and Structure Modeling

Science.gov (United States)

2015-04-28

Germany. p. 18. 2. Oertel, C., On Modeling Contact and Friction Calculation of Tyre Response on Uneven Roads . Vehicle System Dynamics, 1997. 27(S1): p...touching the ground. This massless tip acts as a sensor point and can be used to detect the tire- road contact . Also, using the direction and value of the...superiority of this model as compared to other lumped parameter models currently available. Keywords: Wheeled Vehicle, Terramechanics, Off- Road

Dynamic modelling as an element of the availibility and process oriented behaviour investigation of complex power plants; Dynamische Modellbildung als Element von verfuegbarkeits- und prozessorientierten Untersuchungen komplexer kraftwerkstechnischer Systeme

Energy Technology Data Exchange (ETDEWEB)

Klatt, M.

2007-12-20

A software-tool was developed, which, with its specially built component library, allows the modelling of availability and dynamic behaviour of large scale power plant units. The requested graphic representation near to the process flow schema required a search for new ways of data and information flow modelling. The large quantity of components of a power plant unit with its most important components thereby requires a block oriented modelling approach based on lumped and distributed lumped parameters. (orig.)

Start-up of belt conveyors used for haulage of large lumps under difficult climatic conditions

Energy Technology Data Exchange (ETDEWEB)

Drobny, J

1979-01-01

Investigations are discussed carried out by the Research and Development Center for Brown Coal in Most, Czechoslovakia into effects of climate, weather and mass of coal lumps on reliability of belt conveyors in surface mines. Dirt buildup on the driving drums reduces friction and increases belt sliding hazards. Belt wear increases. Driving drum diameter, increased by the buildup, negatively influences load distribution among the electric motors of the drive system. In extreme cases belt wear and irregular load distribution cause belt failures. Methods for buildup removal used in Czechoslovakia and methods for protection of the return side of a conveyor are described. Effects of large mass of coal lumps and ice buildup on large lumps on the risk of belt damage (cuts, punctures etc,) are discussed. Recommendations for design of coal transfer points are made. 2 refs.

Models for estimating photosynthesis parameters from in situ production profiles

Science.gov (United States)

Kovač, Žarko; Platt, Trevor; Sathyendranath, Shubha; Antunović, Suzana

2017-12-01

The rate of carbon assimilation in phytoplankton primary production models is mathematically prescribed with photosynthesis irradiance functions, which convert a light flux (energy) into a material flux (carbon). Information on this rate is contained in photosynthesis parameters: the initial slope and the assimilation number. The exactness of parameter values is crucial for precise calculation of primary production. Here we use a model of the daily production profile based on a suite of photosynthesis irradiance functions and extract photosynthesis parameters from in situ measured daily production profiles at the Hawaii Ocean Time-series station Aloha. For each function we recover parameter values, establish parameter distributions and quantify model skill. We observe that the choice of the photosynthesis irradiance function to estimate the photosynthesis parameters affects the magnitudes of parameter values as recovered from in situ profiles. We also tackle the problem of parameter exchange amongst the models and the effect it has on model performance. All models displayed little or no bias prior to parameter exchange, but significant bias following parameter exchange. The best model performance resulted from using optimal parameter values. Model formulation was extended further by accounting for spectral effects and deriving a spectral analytical solution for the daily production profile. The daily production profile was also formulated with time dependent growing biomass governed by a growth equation. The work on parameter recovery was further extended by exploring how to extract photosynthesis parameters from information on watercolumn production. It was demonstrated how to estimate parameter values based on a linearization of the full analytical solution for normalized watercolumn production and from the solution itself, without linearization. The paper complements previous works on photosynthesis irradiance models by analysing the skill and consistency of

20 CFR 725.521 - Commutation of payments; lump sum awards.

Science.gov (United States)

2010-04-01

... present value of future benefit payments commuted, computed at 4 percent true discount compounded annually... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Commutation of payments; lump sum awards. 725.521 Section 725.521 Employees' Benefits EMPLOYMENT STANDARDS ADMINISTRATION, DEPARTMENT OF LABOR...

USE OF THE SIMPLE LINEAR REGRESSION MODEL IN MACRO-ECONOMICAL ANALYSES

Directory of Open Access Journals (Sweden)

Constantin ANGHELACHE

2011-10-01

Full Text Available The article presents the fundamental aspects of the linear regression, as a toolbox which can be used in macroeconomic analyses. The article describes the estimation of the parameters, the statistical tests used, the homoscesasticity and heteroskedasticity. The use of econometrics instrument in macroeconomics is an important factor that guarantees the quality of the models, analyses, results and possible interpretation that can be drawn at this level.

An Analysis of the Effect of the U. S. Marine Corps' Lump Sum Selective Reenlistment Bonus Program on Reenlistment Decisions

National Research Council Canada - National Science Library

Barry, Robert

2001-01-01

... the impact of personal characteristics, civilian pay, unemployment, and the lump sum bonus on reenlistment decisions, Marine retention probabilities under the lump sum payment program are compared...

Analysis of a postulated accident scenario involving loss of forced flow in a LMFBR

International Nuclear Information System (INIS)

Moreira, M.L.

1985-01-01

A model to analyse a postulated accident scenario involving loss of forced flow in the reactor vessel of a LMFBR is used. Five phases of the accident are analysed: Natural Circulation, Subcooled Boiling, Nucleate Boiling, Core Dryout and Cladding melt. The heat conduction in the fuel cladding, coolant and lower and upper plenum are calculated by a lump-parameter model. Physical data of a prototype LMFBR reactor were used for the calculation. (author)

A fast semi-analytical model for the slotted structure of induction motors with 36/28 stator/rotor slot combination

NARCIS (Netherlands)

Sprangers, R.L.J.; Paulides, J.J.H.; Gysen, B.L.J.; Lomonova, E.A.

2014-01-01

A fast, semi-analyticalmodel for inductionmotors (IMs) with 36/28 stator/rotor slot combination is presented. In comparison to traditional analytical models for IMs, such as lumped parameter, magnetic equivalent circuit and anisotropic layer models, the presented model calculates a continuous

Soil structure interaction model and variability of parameters in seismic analysis of nuclear island connected building

International Nuclear Information System (INIS)

Subramanian, K.V.; Palekar, S.M.; Bavare, M.S.; Mapari, H.A.; Patel, S.C.; Pillai, C.S.

2005-01-01

This paper provides salient features of the Soil Structure Interaction analysis of Nuclear Island Connected Building (NICB). The dynamic analysis of NICB is performed on a full 3D model accounting for the probable variation in the stiffness of the founding medium. A range analyses was performed to establish the effect of variability of subgrade parameters on the results of seismic analyses of NICB. This paper presents details of various analyses with respect to the subgrade model, uncertainties in subgrade properties, results of seismic analyses and a study of effect of the variability of parameters on the results of these analyses. The results of this study indicate that the variability of soil parameters beyond a certain value of shear wave velocity does not influence the response and in fact the response marginally diminishes. (authors)

Dynamic model including piping acoustics of a centrifugal compression system

NARCIS (Netherlands)

Helvoirt, van J.; Jager, de A.G.

2007-01-01

This paper deals with low frequency pulsation phenomena in full-scale centrifugal compression systems associated with compressor surge. The Greitzer lumped parameter model is applied to describe the dynamic behavior of an industrial compressor test rig and experimental evidence is provided for the

Soil-Related Input Parameters for the Biosphere Model

International Nuclear Information System (INIS)

Smith, A. J.

2004-01-01

This report presents one of the analyses that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN). The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the details of the conceptual model as well as the mathematical model and the required input parameters. The biosphere model is one of a series of process models supporting the postclosure Total System Performance Assessment (TSPA) for the Yucca Mountain repository. A schematic representation of the documentation flow for the Biosphere input to TSPA is presented in Figure 1-1. This figure shows the evolutionary relationships among the products (i.e., analysis and model reports) developed for biosphere modeling, and the biosphere abstraction products for TSPA, as identified in the ''Technical Work Plan for Biosphere Modeling and Expert Support'' (TWP) (BSC 2004 [DIRS 169573]). This figure is included to provide an understanding of how this analysis report contributes to biosphere modeling in support of the license application, and is not intended to imply that access to the listed documents is required to understand the contents of this report. This report, ''Soil-Related Input Parameters for the Biosphere Model'', is one of the five analysis reports that develop input parameters for use in the ERMYN model. This report is the source documentation for the six biosphere parameters identified in Table 1-1. The purpose of this analysis was to develop the biosphere model parameters associated with the accumulation and depletion of radionuclides in the soil. These parameters support the calculation of radionuclide concentrations in soil from on-going irrigation or ash deposition and, as a direct consequence, radionuclide concentration in other environmental media that are affected by radionuclide concentrations in soil. The analysis was performed in accordance with the TWP (BSC 2004 [DIRS 169573]) where the governing procedure was defined as AP-SIII.9Q, ''Scientific Analyses''. This

The liquid lift: Looking natural without lumps

Directory of Open Access Journals (Sweden)

Iñigo de Felipe

2015-01-01

Full Text Available Context: Hyaluronic acid (HA is the most common filler used to rejuvenate. Today, a three-dimensional approach prevails over previous techniques in which this material was used in specific areas of the face such as the nasolabial fold, the marionette line, and the eye trough giving a strange appearance that does not look natural. Even with a volumizing purpose, the injection of HA can sometimes produce clinically detectable nodules or lumps where the filler is deposited. Aims: To develop a new technique of injecting HA that can provide more natural results and avoid the lumpiness and nodular appearance that sometimes occurs with the injection of HA. To detect whether mixing HA with diluted anesthetic agent modifies its behavior. Settings and Design: Prospective, case control, single-center study on a private clinic setting. Materials and Methods: Eighty six patients were enrolled in this study. All of them had a previous treatment with nondiluted HA using a needle at least a year before. Patients were injected with 8 mL of reticulated HA (RHA mixed with 6 mL of saline and 2 mL of anesthetic agent. The mixture was administered through a cannula inserted in the face, one at mid-cheek and another at frontal-temporal point of entry. Owing to the lifting effect of this mixture we called this procedure liquid lift (LL. Patients were evaluated 1 month, 6 months, and a year later and asked to compare the LL with previous experiences in terms of natural look, pain, and appearance of nodules. Statistical Analysis Used: Student′s t-test. Results: One month after the treatment, 83 out of 86 patients (96.5% thought LL produced a more natural look than the previous treatment with the needle. Sixty two (72% considered LL less painful than the previous treatment and only eight (9.3% could detect lumps or nodules 1 month after LL was performed compared with 46 (53.5% that described this problem with previous needle injections. The incidence of bruising was

Frequency Combs in a Lumped-Element Josephson-Junction Circuit

Science.gov (United States)

Khan, Saeed; Türeci, Hakan E.

2018-04-01

We investigate the dynamics of a microwave-driven Josephson junction capacitively coupled to a lumped-element L C oscillator. In the regime of driving where the Josephson junction can be approximated as a Kerr oscillator, this minimal nonlinear system has been previously shown to exhibit a bistability in phase and amplitude. In the present study, we characterize the full phase diagram and show that besides a parameter regime exhibiting bistability, there is also a regime of self-oscillations characterized by a frequency comb in its spectrum. We discuss the mechanism of comb generation which appears to be different from those studied in microcavity frequency combs and mode-locked lasers. We then address the fate of the comblike spectrum in the regime of strong quantum fluctuations, reached when nonlinearity becomes the dominant scale with respect to dissipation. We find that the nonlinearity responsible for the emergence of the frequency combs also leads to its dephasing, leading to broadening and ultimate disappearance of sharp spectral peaks. Our study explores the fundamental question of the impact of quantum fluctuations for quantum systems which do not possess a stable fixed point in the classical limit.

Lumped Thermal Household Model

DEFF Research Database (Denmark)

Biegel, Benjamin; Andersen, Palle; Stoustrup, Jakob

2013-01-01

pump portfolio. Following, we illustrate two disadvantages of individual models, namely that it requires much computational effort to optimize over a large portfolio, and second that it is difficult to accurately model the houses in certain time periods due to local disturbances. Finally, we propose...

Parameter estimation in nonlinear models for pesticide degradation

International Nuclear Information System (INIS)

Richter, O.; Pestemer, W.; Bunte, D.; Diekkrueger, B.

1991-01-01

A wide class of environmental transfer models is formulated as ordinary or partial differential equations. With the availability of fast computers, the numerical solution of large systems became feasible. The main difficulty in performing a realistic and convincing simulation of the fate of a substance in the biosphere is not the implementation of numerical techniques but rather the incomplete data basis for parameter estimation. Parameter estimation is a synonym for statistical and numerical procedures to derive reasonable numerical values for model parameters from data. The classical method is the familiar linear regression technique which dates back to the 18th century. Because it is easy to handle, linear regression has long been established as a convenient tool for analysing relationships. However, the wide use of linear regression has led to an overemphasis of linear relationships. In nature, most relationships are nonlinear and linearization often gives a poor approximation of reality. Furthermore, pure regression models are not capable to map the dynamics of a process. Therefore, realistic models involve the evolution in time (and space). This leads in a natural way to the formulation of differential equations. To establish the link between data and dynamical models, numerical advanced parameter identification methods have been developed in recent years. This paper demonstrates the application of these techniques to estimation problems in the field of pesticide dynamics. (7 refs., 5 figs., 2 tabs.)

Lumped elements for RF and microwave circuits

CERN Document Server

Bahl, Inder

2003-01-01

Due to the unprecedented growth in wireless applications over the past decade, development of low-cost solutions for RF and microwave communication systems has become of great importance. This practical new book is the first comprehensive treatment of lumped elements, which are playing a critical role in the development of the circuits that make these cost-effective systems possible. The books offers you an in-depth understanding of the different types of RF and microwave circuit elements, including inductors, capacitors, resistors, transformers, via holes, airbridges, and crossovers. Support

On the use of uncertainty analyses to test hypotheses regarding deterministic model predictions of environmental processes

International Nuclear Information System (INIS)

Gilbert, R.O.; Bittner, E.A.; Essington, E.H.

1995-01-01

This paper illustrates the use of Monte Carlo parameter uncertainty and sensitivity analyses to test hypotheses regarding predictions of deterministic models of environmental transport, dose, risk and other phenomena. The methodology is illustrated by testing whether 238 Pu is transferred more readily than 239+240 Pu from the gastrointestinal (GI) tract of cattle to their tissues (muscle, liver and blood). This illustration is based on a study wherein beef-cattle grazed for up to 1064 days on a fenced plutonium (Pu)-contaminated arid site in Area 13 near the Nevada Test Site in the United States. Periodically, cattle were sacrificed and their tissues analyzed for Pu and other radionuclides. Conditional sensitivity analyses of the model predictions were also conducted. These analyses indicated that Pu cattle tissue concentrations had the largest impact of any model parameter on the pdf of predicted Pu fractional transfers. Issues that arise in conducting uncertainty and sensitivity analyses of deterministic models are discussed. (author)

Effect of piping systems on surge in centrifugal compressors

International Nuclear Information System (INIS)

Tamaki, Hideaki

2008-01-01

There is a possibility that the exchange of the piping system may change the surge characteristic of a compressor. The piping system of a plant is not always the same as that of a test site. Then it is important to evaluate the effect of piping systems on surge characteristics in centrifugal compressors. Several turbochargers combined with different piping systems were tested. The lumped parameter model which was simplified to be solved easily was applied for the prediction of surge point. Surge lines were calculated with the linearlized lumped parameter model. The difference between the test and calculated results was within 10 %. Trajectory of surge cycle was also examined by solving the lumped parameter model. Mild surge and deep surge were successfully predicted. This study confirmed that the lumped parameter model was a very useful tool to predict the effect of piping systems on surge characteristics in centrifugal compressors, even though that was a simple model

A Novel T-Fed 4-Element Quasi-Lumped Resonator Antenna Array

Directory of Open Access Journals (Sweden)

S.S. Olokede

2014-06-01

Full Text Available In this paper, electrically small corporately T-fed quasi-lumped element resonator antenna array is investigated. The radiating element, a quasi-lumped element resonator is excited by a novel semi hybrid ring-like T-shaped corporate feed network. The characteristics losses due to Ohmic and discontinuities along the feed line which invariably constitutes complex feed structures are mitigated at the instance of the proposed antenna. Technique to implement the compact array with the intent to enhance the gain is presented. The operation dynamics of the feed along with its theoretical explanation is also reported. Findings indicates that the measured gain is 10.97 dBi for antenna of an estate area of about 0.677λ_0 × 1.257λ_0 sq. mm. Valuable insight to the optimum design in terms of compactness, good gain, and ease of fabrication is documented.

The welfare gain from replacing the health insurance tax exclusion with lump-sum tax credits.

Science.gov (United States)

Liu, Liqun; Rettenmaier, Andrew J; Saving, Thomas R

2011-06-01

This paper analyzes the welfare gain from replacing the tax exclusion of employer-provided health insurance with a lump-sum tax credit. It differs from earlier studies in that we look at the welfare cost of health insurance tax exclusion as coming directly from excessive health insurance rather than from overconsumption of medical care and that we account for the labor market effect of the tax exclusion on welfare. Both differences work to produce a smaller tax reform welfare gain. For a set of mid-range parameter values, the welfare gain is about 21% of current health insurance tax expenditures. In addition, government tax expenditures would fall by 38%, and health insurance spending would fall by 77% after the reform.

Soil-Related Input Parameters for the Biosphere Model

Energy Technology Data Exchange (ETDEWEB)

A. J. Smith

2004-09-09

This report presents one of the analyses that support the Environmental Radiation Model for Yucca Mountain Nevada (ERMYN). The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes the details of the conceptual model as well as the mathematical model and the required input parameters. The biosphere model is one of a series of process models supporting the postclosure Total System Performance Assessment (TSPA) for the Yucca Mountain repository. A schematic representation of the documentation flow for the Biosphere input to TSPA is presented in Figure 1-1. This figure shows the evolutionary relationships among the products (i.e., analysis and model reports) developed for biosphere modeling, and the biosphere abstraction products for TSPA, as identified in the ''Technical Work Plan for Biosphere Modeling and Expert Support'' (TWP) (BSC 2004 [DIRS 169573]). This figure is included to provide an understanding of how this analysis report contributes to biosphere modeling in support of the license application, and is not intended to imply that access to the listed documents is required to understand the contents of this report. This report, ''Soil-Related Input Parameters for the Biosphere Model'', is one of the five analysis reports that develop input parameters for use in the ERMYN model. This report is the source documentation for the six biosphere parameters identified in Table 1-1. The purpose of this analysis was to develop the biosphere model parameters associated with the accumulation and depletion of radionuclides in the soil. These parameters support the calculation of radionuclide concentrations in soil from on-going irrigation or ash deposition and, as a direct consequence, radionuclide concentration in other environmental media that are affected by radionuclide concentrations in soil. The analysis was performed in accordance with the TWP (BSC 2004 [DIRS 169573]) where the governing procedure

Experimental Modeling of Monolithic Resistors for Silicon ICS with a Robust Optimizer-Driving Scheme

Directory of Open Access Journals (Sweden)

Philippe Leduc

2002-06-01

Full Text Available Today, an exhaustive library of models describing the electrical behavior of integrated passive components in the radio-frequency range is essential for the simulation and optimization of complex circuits. In this work, a preliminary study has been done on Tantalum Nitride (TaN resistors integrated on silicon, and this leads to a single p-type lumped-element circuit. An efficient extraction technique will be presented to provide a computer-driven optimizer with relevant initial model parameter values (the "guess-timate". The results show the unicity in most cases of the lumped element determination, which leads to a precise simulation of self-resonant frequencies.

Seismic response time history analyses for KALIMER building with a horizontal and vertical seismic isolation

International Nuclear Information System (INIS)

Lee, J. H.; Yoo, B.; Koo, K. H.

2001-01-01

The seismic response time history analyses for the lumped mass models of KALIMER reactor building with a horizontal and vertical seismic isolation are performed for Artificial Time History and Kobe earthquake. The vertical amplification by the horizontal isolation is reduced by a vertical isolation for both earthquakes. The 3% viscous damping and the vertical isolation frequency of 1.5Hz gives a reduced vertical response compared to the fixed base condition at reactor support, and the 9% viscous damping to Kobe earthquake is required to get an equivalent vertical response with a fixed base condition

Seismic response time history analyses for KALIMER building with a horizontal and vertical seismic isolation

Energy Technology Data Exchange (ETDEWEB)

Lee, J. H.; Yoo, B.; Koo, K. H. [KAERI, Taejon (Korea, Republic of)

2001-05-01

The seismic response time history analyses for the lumped mass models of KALIMER reactor building with a horizontal and vertical seismic isolation are performed for Artificial Time History and Kobe earthquake. The vertical amplification by the horizontal isolation is reduced by a vertical isolation for both earthquakes. The 3% viscous damping and the vertical isolation frequency of 1.5Hz gives a reduced vertical response compared to the fixed base condition at reactor support, and the 9% viscous damping to Kobe earthquake is required to get an equivalent vertical response with a fixed base condition.

Assessment of managed aquifer recharge potential using ensembles of local models.

Science.gov (United States)

Smith, Anthony J; Pollock, Daniel W

2012-01-01

A simple quantitative approach for assessing the artificial recharge potential of large regions using spatial ensembles of local models is proposed. The method extends existing qualitative approaches and enables rapid assessments within a programmable environment. Spatial discretization of a water resource region into continuous local domains allows simple local models to be applied independently in each domain using lumped parameters. The ensemble results can be analyzed directly or combined with other quantitative and thematic information and visualized as regional suitability maps. A case study considers the hydraulic potential for surface infiltration across a large water resource region using a published analytic model for basin recharge. The model solution was implemented within a geographic information system and evaluated independently in >21,000 local domains using lumped parameters derived from existing regional datasets. Computer execution times to run the whole ensemble and process the results were in the order of a few minutes. Relevant aspects of the case study results and general conclusions concerning the utility and limitations of the method are discussed. © 2011, CSIRO. Ground Water © 2011, National Ground Water Association.

Calculation methods for simulation and modelling of nuclear power plant accidents

International Nuclear Information System (INIS)

Zurita Centelles, A.

1985-01-01

The study deals with the development of calculation procedures for the determination of transient operating conditions in pressurized water reactors, which present the following characteristics: application of largely analytic methods for the description of primary circuit components; strict modular structure of the program for the easy exchange of component models; applicability of different component models according to the applicable case; large valid ranges of application of the thermodynamic variables of state in the transient models; in case of necessity exchange possibility of slip, pressure drop and heat transmission correlations as well as other functions; application in the dynamic components analyses of the anglo-saxon lumped parameter suitable for the system instrumentation. With these calculation procedures it is possible to analyse the effect of a certain selection of transients - up to reaching turbine tripout and reactor emergency shutdown - in the individual primary circuit components. These transients may be generally classified amongst the heat rejection and heat input modifications in the secondary circuit, in the coolant or in the reactivity balance and power distribution. (orig.) [de

Advantages and disadvantages of lumping together gastroesophageal reflux disease and dyspepsia

NARCIS (Netherlands)

Smout, André J. P. M.

2006-01-01

PURPOSE OF REVIEW: The aim of this article is to identify and to balance the arguments in favor of and against lumping together gastroesophageal reflux disease and functional dyspepsia. RECENT FINDINGS: In at least half of the patients diagnosed with gastroesophageal reflux disease no organic

Comparative study of aspiration and non-aspiration cytology of palpable breast lumps and correlation with histopathology

Directory of Open Access Journals (Sweden)

S Koirala

2014-09-01

Full Text Available Background: Breast lump is one of the most common presentations in surgical outpatient departments with anxiety regarding a possible malignancy. Hence a quick diagnosis of a lump in the breast is essential. Fine needle aspiration cytology is an ideal initial diagnostic modality in breast lumps. There is an alternative method of performing needle aspiration, known as fine needle capillary cytology where the specimen is obtained using just a needle without aspiration.Materials and Methods: This hospital-based cross sectional analytical study was carried out in Department of Pathology in National Academy of Medical Sciences, Bir Hospital for one year. The objective of this study was to compare aspiration and non-aspiration cytology of palpable breast lumps and correlation with histopathology.Results: The five criteria scored for each technique were background blood, amount of cellular material, cellular degeneration, cellular trauma and architectural preservation. Compared to fine needle aspiration cytology, fine needle capillary cytology yields less bloody smears with minimal degenerative changes and offers more diagnostically superior specimens. Fine needle aspiration cytology, on the other hand, gives a good yield of diagnostic material.Conclusion: Fine needle aspiration cytology and fine needle capillary cytology are quick, easy, safe and cost-effective techniques. . A high sensitivity and specificity of cytological diagnosis in this study proves that it is comparable to final histology report in its diagnostic efficiency. Thus, fine needle aspiration cytology is a very important preliminary diagnostic test in palpable breast lumps and the results show a high degree of correlation with the final histopathology report.DOI: http://dx.doi.org/10.3126/jpn.v4i8.11501 Journal of Pathology of Nepal; Vol.4,No. 8 (2014 639-643

Optimum Design of Plasma Focus

International Nuclear Information System (INIS)

Ramos, Ruben; Gonzalez, Jose; Clausse, Alejandro

2000-01-01

The optimum design of Plasma Focus devices is presented based in a lumped parameter model of the MHD equations.Maps in the design parameters space are obtained, which determine the length and deuterium pressure required to produce a given neutron yield.Sensitivity analyses of the main effective numbers (sweeping efficiencies) was performed, and lately the optimum values were determined in order to set a basis for the conceptual design

Generic uncertainty model for DETRA for environmental consequence analyses. Application and sample outputs

International Nuclear Information System (INIS)

Suolanen, V.; Ilvonen, M.

1998-10-01

Computer model DETRA applies a dynamic compartment modelling approach. The compartment structure of each considered application can be tailored individually. This flexible modelling method makes it possible that the transfer of radionuclides can be considered in various cases: aquatic environment and related food chains, terrestrial environment, food chains in general and food stuffs, body burden analyses of humans, etc. In the former study on this subject, modernization of the user interface of DETRA code was carried out. This new interface works in Windows environment and the usability of the code has been improved. The objective of this study has been to further develop and diversify the user interface so that also probabilistic uncertainty analyses can be performed by DETRA. The most common probability distributions are available: uniform, truncated Gaussian and triangular. The corresponding logarithmic distributions are also available. All input data related to a considered case can be varied, although this option is seldomly needed. The calculated output values can be selected as monitored values at certain simulation time points defined by the user. The results of a sensitivity run are immediately available after simulation as graphical presentations. These outcomes are distributions generated for varied parameters, density functions of monitored parameters and complementary cumulative density functions (CCDF). An application considered in connection with this work was the estimation of contamination of milk caused by radioactive deposition of Cs (10 kBq(Cs-137)/m 2 ). The multi-sequence calculation model applied consisted of a pasture modelling part and a dormant season modelling part. These two sequences were linked periodically simulating the realistic practice of care taking of domestic animals in Finland. The most important parameters were varied in this exercise. The performed diversifying of the user interface of DETRA code seems to provide an easily

Implementation into a CFD code of neutron kinetics and fuel pin models for nuclear reactor transient analyses

International Nuclear Information System (INIS)

Chen Zhao; Chen, Xue-Nong; Rineiski, Andrei; Zhao Pengcheng; Chen Hongli

2014-01-01

Safety analysis is an important tool for justifying the safety of nuclear reactors. The traditional method for nuclear reactor safety analysis is performed by means of system codes, which use one-dimensional lumped-parameter method to model real reactor systems. However, there are many multi-dimensional thermal-hydraulic phenomena cannot be predicated using traditional one-dimensional system codes. This problem is extremely important for pool-type nuclear systems. Computational fluid dynamics (CFD) codes are powerful numerical simulation tools to solve multi-dimensional thermal-hydraulics problems, which are widely used in industrial applications for single phase flows. In order to use general CFD codes to solve nuclear reactor transient problems, some additional models beyond general ones are required. Neutron kinetics model for power calculation and fuel pin model for fuel pin temperature calculation are two important models of these additional models. The motivation of this work is to develop an advance numerical simulation method for nuclear reactor safety analysis by implementing neutron kinetics model and fuel pin model into general CFD codes. In this paper, the Point Kinetics Model (PKM) and Fuel Pin Model (FPM) are implemented into a general CFD code FLUENT. The improved FLUENT was called as FLUENT/PK. The mathematical models and implementary method of FLUENT/PK are descripted and two demonstration application cases, e.g. the unprotected transient overpower (UTOP) accident of a Liquid Metal cooled Fast Reactor (LMFR) and the unprotected beam overpower (UBOP) accident of an Accelerator Driven System (ADS), are presented. (author)

Room Heat-Up Analysis with GOTHIC code

International Nuclear Information System (INIS)

Jimenez, G.; Olza, J. M.

2010-01-01

The GOTHIC T M computer code is a state-of-the art program for modeling multiphase, multicomponent fluid flow. GOTHIC is rapidly becoming the industry-standard code for performing both containment design basis accident (DBA) analyses and analyses to support equipment qualification. GOTHIC has a flexible nodding structure that allows both lumped parameter and 3-D modeling capabilities. Multidimensional analysis capabilities greatly enhance the study of noncondensable gases and stratification and permit the calculation of flow field details within any given volume.

Variability of dynamic source parameters inferred from kinematic models of past earthquakes

KAUST Repository

Causse, M.

2013-12-24

We analyse the scaling and distribution of average dynamic source properties (fracture energy, static, dynamic and apparent stress drops) using 31 kinematic inversion models from 21 crustal earthquakes. Shear-stress histories are computed by solving the elastodynamic equations while imposing the slip velocity of a kinematic source model as a boundary condition on the fault plane. This is achieved using a 3-D finite difference method in which the rupture kinematics are modelled with the staggered-grid-split-node fault representation method of Dalguer & Day. Dynamic parameters are then estimated from the calculated stress-slip curves and averaged over the fault plane. Our results indicate that fracture energy, static, dynamic and apparent stress drops tend to increase with magnitude. The epistemic uncertainty due to uncertainties in kinematic inversions remains small (ϕ ∼ 0.1 in log10 units), showing that kinematic source models provide robust information to analyse the distribution of average dynamic source parameters. The proposed scaling relations may be useful to constrain friction law parameters in spontaneous dynamic rupture calculations for earthquake source studies, and physics-based near-source ground-motion prediction for seismic hazard and risk mitigation.

Longitudinal changes in telomere length and associated genetic parameters in dairy cattle analysed using random regression models.

Directory of Open Access Journals (Sweden)

Luise A Seeker

Full Text Available Telomeres cap the ends of linear chromosomes and shorten with age in many organisms. In humans short telomeres have been linked to morbidity and mortality. With the accumulation of longitudinal datasets the focus shifts from investigating telomere length (TL to exploring TL change within individuals over time. Some studies indicate that the speed of telomere attrition is predictive of future disease. The objectives of the present study were to 1 characterize the change in bovine relative leukocyte TL (RLTL across the lifetime in Holstein Friesian dairy cattle, 2 estimate genetic parameters of RLTL over time and 3 investigate the association of differences in individual RLTL profiles with productive lifespan. RLTL measurements were analysed using Legendre polynomials in a random regression model to describe TL profiles and genetic variance over age. The analyses were based on 1,328 repeated RLTL measurements of 308 female Holstein Friesian dairy cattle. A quadratic Legendre polynomial was fitted to the fixed effect of age in months and to the random effect of the animal identity. Changes in RLTL, heritability and within-trait genetic correlation along the age trajectory were calculated and illustrated. At a population level, the relationship between RLTL and age was described by a positive quadratic function. Individuals varied significantly regarding the direction and amount of RLTL change over life. The heritability of RLTL ranged from 0.36 to 0.47 (SE = 0.05-0.08 and remained statistically unchanged over time. The genetic correlation of RLTL at birth with measurements later in life decreased with the time interval between samplings from near unity to 0.69, indicating that TL later in life might be regulated by different genes than TL early in life. Even though animals differed in their RLTL profiles significantly, those differences were not correlated with productive lifespan (p = 0.954.

Analytical modelling of hydrogen transport in reactor containments

International Nuclear Information System (INIS)

Manno, V.P.

1983-09-01

A versatile computational model of hydrogen transport in nuclear plant containment buildings is developed. The background and significance of hydrogen-related nuclear safety issues are discussed. A computer program is constructed that embodies the analytical models. The thermofluid dynamic formulation spans a wide applicability range from rapid two-phase blowdown transients to slow incompressible hydrogen injection. Detailed ancillary models of molecular and turbulent diffusion, mixture transport properties, multi-phase multicomponent thermodynamics and heat sink modelling are addressed. The numerical solution of the continuum equations emphasizes both accuracy and efficiency in the employment of relatively coarse discretization and long time steps. Reducing undesirable numerical diffusion is addressed. Problem geometry options include lumped parameter zones, one dimensional meshs, two dimensional Cartesian or axisymmetric coordinate systems and three dimensional Cartesian or cylindrical regions. An efficient lumped nodal model is included for simulation of events in which spatial resolution is not significant. Several validation calculations are reported

SVM models for analysing the headstreams of mine water inrush

Energy Technology Data Exchange (ETDEWEB)

Yan Zhi-gang; Du Pei-jun; Guo Da-zhi [China University of Science and Technology, Xuzhou (China). School of Environmental Science and Spatial Informatics

2007-08-15

The support vector machine (SVM) model was introduced to analyse the headstrean of water inrush in a coal mine. The SVM model, based on a hydrogeochemical method, was constructed for recognising two kinds of headstreams and the H-SVMs model was constructed for recognising multi- headstreams. The SVM method was applied to analyse the conditions of two mixed headstreams and the value of the SVM decision function was investigated as a means of denoting the hydrogeochemical abnormality. The experimental results show that the SVM is based on a strict mathematical theory, has a simple structure and a good overall performance. Moreover the parameter W in the decision function can describe the weights of discrimination indices of the headstream of water inrush. The value of the decision function can denote hydrogeochemistry abnormality, which is significant in the prevention of water inrush in a coal mine. 9 refs., 1 fig., 7 tabs.

Is there any correlation between model-based perfusion parameters and model-free parameters of time-signal intensity curve on dynamic contrast enhanced MRI in breast cancer patients?

Energy Technology Data Exchange (ETDEWEB)

Yi, Boram; Kang, Doo Kyoung; Kim, Tae Hee [Ajou University School of Medicine, Department of Radiology, Suwon, Gyeonggi-do (Korea, Republic of); Yoon, Dukyong [Ajou University School of Medicine, Department of Biomedical Informatics, Suwon (Korea, Republic of); Jung, Yong Sik; Kim, Ku Sang [Ajou University School of Medicine, Department of Surgery, Suwon (Korea, Republic of); Yim, Hyunee [Ajou University School of Medicine, Department of Pathology, Suwon (Korea, Republic of)

2014-05-15

To find out any correlation between dynamic contrast-enhanced (DCE) model-based parameters and model-free parameters, and evaluate correlations between perfusion parameters with histologic prognostic factors. Model-based parameters (Ktrans, Kep and Ve) of 102 invasive ductal carcinomas were obtained using DCE-MRI and post-processing software. Correlations between model-based and model-free parameters and between perfusion parameters and histologic prognostic factors were analysed. Mean Kep was significantly higher in cancers showing initial rapid enhancement (P = 0.002) and a delayed washout pattern (P = 0.001). Ve was significantly lower in cancers showing a delayed washout pattern (P = 0.015). Kep significantly correlated with time to peak enhancement (TTP) (ρ = -0.33, P < 0.001) and washout slope (ρ = 0.39, P = 0.002). Ve was significantly correlated with TTP (ρ = 0.33, P = 0.002). Mean Kep was higher in tumours with high nuclear grade (P = 0.017). Mean Ve was lower in tumours with high histologic grade (P = 0.005) and in tumours with negative oestrogen receptor status (P = 0.047). TTP was shorter in tumours with negative oestrogen receptor status (P = 0.037). We could acquire general information about the tumour vascular physiology, interstitial space volume and pathologic prognostic factors by analyzing time-signal intensity curve without a complicated acquisition process for the model-based parameters. (orig.)

Taking the mystery out of mathematical model applications to karst aquifers—A primer

Science.gov (United States)

Kuniansky, Eve L.

2014-01-01

Advances in mathematical model applications toward the understanding of the complex flow, characterization, and water-supply management issues for karst aquifers have occurred in recent years. Different types of mathematical models can be applied successfully if appropriate information is available and the problems are adequately identified. The mathematical approaches discussed in this paper are divided into three major categories: 1) distributed parameter models, 2) lumped parameter models, and 3) fitting models. The modeling approaches are described conceptually with examples (but without equations) to help non-mathematicians understand the applications.

airGR: an R-package suitable for large sample hydrology presenting a suite of lumped hydrological models

Science.gov (United States)

Thirel, G.; Delaigue, O.; Coron, L.; Perrin, C.; Andreassian, V.

2016-12-01

Lumped hydrological models are useful and convenient tools for research, engineering and educational purposes. They propose catchment-scale representations of the precipitation-discharge relationship. Thanks to their limited data requirements, they can be easily implemented and run. With such models, it is possible to simulate a number of hydrological key processes over the catchment with limited structural and parametric complexity, typically evapotranspiration, runoff, underground losses, etc. The Hydrology Group at Irstea (Antony) has been developing a suite of rainfall-runoff models over the past 30 years with the main objectives of designing models as efficient as possible in terms of streamflow simulation, applicable to a wide range of catchments and having low data requirements. This resulted in a suite of models running at different time steps (from hourly to annual) applicable for various issues including water balance estimation, forecasting, simulation of impacts and scenario testing. Recently, Irstea has developed an easy-to-use R-package (R Core Team, 2015; Coron et al., 2016), called airGR, to make these models widely available. It includes: - the water balance annual GR1A (Mouehli et al., 2006), - the monthly GR2M (Mouehli, 2003) models, - three versions of the daily model, namely GR4J (Perrin et al., 2003), GR5J (Le Moine, 2008) and GR6J (Pushpalatha et al., 2011), - the hourly GR4H model (Mathevet, 2005), - a degree-day snow module CemaNeige (Valéry et al., 2014). The airGR package has been designed to facilitate the use by non-expert users and allow the addition of evaluation criteria, models or calibration algorithm selected by the end-user. Each model core is coded in FORTRAN to ensure low computational time. The other package functions (i.e. mainly the calibration algorithm and the efficiency criteria) are coded in R. The package is already used for educational purposes. It allows for convenient implementation of model inter-comparisons and

Mass and Heat Transfer Analysis of Membrane Humidifier with a Simple Lumped Mass Model

International Nuclear Information System (INIS)

Lee, Young Duk; Bae, Ho June; Ahn, Kook Young; Yu, Sang Seok; Hwang, Joon Young

2009-01-01

The performance of proton exchange membrane fuel cell (PEMFC) is seriously changed by the humidification condition which is intrinsic characteristics of the PEMFC. Typically, the humidification of fuel cell is carried out with internal or external humidifier. A membrane humidifier is applied to the external humidification of residential power generation fuel cell due to its convenience and high performance. In this study, a simple static model is constructed to understand the physical phenomena of the membrane humidifier in terms of geometric parameters and operating parameters. The model utilizes the concept of shell and tube heat exchanger but the model is also able to estimate the mass transport through the membrane. Model is constructed with FORTRAN under Matlab/Simulink □ environment to keep consistency with other components model which we already developed. Results shows that the humidity of wet gas and membrane thickness are critical parameters to improve the performance of the humidifier

Parameter optimization for surface flux transport models

Science.gov (United States)

Whitbread, T.; Yeates, A. R.; Muñoz-Jaramillo, A.; Petrie, G. J. D.

2017-11-01

Accurate prediction of solar activity calls for precise calibration of solar cycle models. Consequently we aim to find optimal parameters for models which describe the physical processes on the solar surface, which in turn act as proxies for what occurs in the interior and provide source terms for coronal models. We use a genetic algorithm to optimize surface flux transport models using National Solar Observatory (NSO) magnetogram data for Solar Cycle 23. This is applied to both a 1D model that inserts new magnetic flux in the form of idealized bipolar magnetic regions, and also to a 2D model that assimilates specific shapes of real active regions. The genetic algorithm searches for parameter sets (meridional flow speed and profile, supergranular diffusivity, initial magnetic field, and radial decay time) that produce the best fit between observed and simulated butterfly diagrams, weighted by a latitude-dependent error structure which reflects uncertainty in observations. Due to the easily adaptable nature of the 2D model, the optimization process is repeated for Cycles 21, 22, and 24 in order to analyse cycle-to-cycle variation of the optimal solution. We find that the ranges and optimal solutions for the various regimes are in reasonable agreement with results from the literature, both theoretical and observational. The optimal meridional flow profiles for each regime are almost entirely within observational bounds determined by magnetic feature tracking, with the 2D model being able to accommodate the mean observed profile more successfully. Differences between models appear to be important in deciding values for the diffusive and decay terms. In like fashion, differences in the behaviours of different solar cycles lead to contrasts in parameters defining the meridional flow and initial field strength.

Primary Breast Tuberculosis Presenting as a Lump: A Rare Modern ...

African Journals Online (AJOL)

A 25‑year‑old female presented with a painless lump in her right breast for 1 month duration. She gave history of low grade fever off and on for the last 2 weeks. There were no other complaints like weight loss, loss of appetite, and any cough. She was unmarried and there was no positive family history of breast tuberculosis.

MOESHA: A genetic algorithm for automatic calibration and estimation of parameter uncertainty and sensitivity of hydrologic models

Science.gov (United States)

Characterization of uncertainty and sensitivity of model parameters is an essential and often overlooked facet of hydrological modeling. This paper introduces an algorithm called MOESHA that combines input parameter sensitivity analyses with a genetic algorithm calibration routin...

Catchment variability and parameter estimation in multi-objective regionalisation of a rainfall-runoff model

NARCIS (Netherlands)

Deckers, Dave L.E.H.; Booij, Martijn J.; Rientjes, T.H.M.; Krol, Martinus S.

2010-01-01

This study attempts to examine if catchment variability favours regionalisation by principles of catchment similarity. Our work combines calibration of a simple conceptual model for multiple objectives and multi-regression analyses to establish a regional model between model sensitive parameters and

Breast Lumps: A 21‑Year Single‑Center Clinical and Histological ...

African Journals Online (AJOL)

Results: Only 38% of the patients came within 3 months of finding lumps in their breast. Onehundred and thirty‑seven patients (83%) had benign disease, i.e., fibroadenoma, mammary dysplasia, cysts, adenomas, tuberculosis, phyllodes tumor, mastitis, and lipoma. Only 16.9% i.e., 28 patients had breast cancer, out of which ...

Analyses and simulations in income frame regulation model for the network sector from 2007

International Nuclear Information System (INIS)

Askeland, Thomas Haave; Fjellstad, Bjoern

2007-01-01

Analyses of the income frame regulation model for the network sector in Norway, introduced 1.st of January 2007. The model's treatment of the norm cost is evaluated, especially the effect analyses carried out by a so called Data Envelopment Analysis model. It is argued that there may exist an age lopsidedness in the data set, and that this should and can be corrected in the effect analyses. The adjustment is proposed corrected for by introducing an age parameter in the data set. Analyses of how the calibration effects in the regulation model affect the business' total income frame, as well as each network company's income frame have been made. It is argued that the calibration, the way it is presented, is not working according to its intention, and should be adjusted in order to provide the sector with the rate of reference in return (ml)

Channel flow and trichloroethylene treatment in a partly iron-filled fracture: Experimental and model results

Science.gov (United States)

Cai, Zuansi; Merly, Corrine; Thomson, Neil R.; Wilson, Ryan D.; Lerner, David N.

2007-08-01

Technical developments have now made it possible to emplace granular zero-valent iron (Fe 0) in fractured media to create a Fe 0 fracture reactive barrier (Fe 0 FRB) for the treatment of contaminated groundwater. To evaluate this concept, we conducted a laboratory experiment in which trichloroethylene (TCE) contaminated water was flushed through a single uniform fracture created between two sandstone blocks. This fracture was partly filled with what was intended to be a uniform thickness of iron. Partial treatment of TCE by iron demonstrated that the concept of a Fe 0 FRB is practical, but was less than anticipated for an iron layer of uniform thickness. When the experiment was disassembled, evidence of discrete channelised flow was noted and attributed to imperfect placement of the iron. To evaluate the effect of the channel flow, an explicit Channel Model was developed that simplifies this complex flow regime into a conceptualised set of uniform and parallel channels. The mathematical representation of this conceptualisation directly accounts for (i) flow channels and immobile fluid arising from the non-uniform iron placement, (ii) mass transfer from the open fracture to iron and immobile fluid regions, and (iii) degradation in the iron regions. A favourable comparison between laboratory data and the results from the developed mathematical model suggests that the model is capable of representing TCE degradation in fractures with non-uniform iron placement. In order to apply this Channel Model concept to a Fe 0 FRB system, a simplified, or implicit, Lumped Channel Model was developed where the physical and chemical processes in the iron layer and immobile fluid regions are captured by a first-order lumped rate parameter. The performance of this Lumped Channel Model was compared to laboratory data, and benchmarked against the Channel Model. The advantages of the Lumped Channel Model are that the degradation of TCE in the system is represented by a first

Reduction of chemical reaction models

Science.gov (United States)

Frenklach, Michael

1991-01-01

An attempt is made to reconcile the different terminologies pertaining to reduction of chemical reaction models. The approaches considered include global modeling, response modeling, detailed reduction, chemical lumping, and statistical lumping. The advantages and drawbacks of each of these methods are pointed out.

State space model extraction of thermohydraulic systems – Part I: A linear graph approach

International Nuclear Information System (INIS)

Uren, K.R.; Schoor, G. van

2013-01-01

Thermohydraulic simulation codes are increasingly making use of graphical design interfaces. The user can quickly and easily design a thermohydraulic system by placing symbols on the screen resembling system components. These components can then be connected to form a system representation. Such system models may then be used to obtain detailed simulations of the physical system. Usually this kind of simulation models are too complex and not ideal for control system design. Therefore, a need exists for automated techniques to extract lumped parameter models useful for control system design. The goal of this first paper, in a two part series, is to propose a method that utilises a graphical representation of a thermohydraulic system, and a lumped parameter modelling approach, to extract state space models. In this methodology each physical domain of the thermohydraulic system is represented by a linear graph. These linear graphs capture the interaction between all components within and across energy domains – hydraulic, thermal and mechanical. These linear graphs are analysed using a graph-theoretic approach to derive reduced order state space models. These models capture the dominant dynamics of the thermohydraulic system and are ideal for control system design purposes. The proposed state space model extraction method is demonstrated by considering a U-tube system. A non-linear state space model is extracted representing both the hydraulic and thermal domain dynamics of the system. The simulated state space model is compared with a Flownex ® model of the U-tube. Flownex ® is a validated systems thermal-fluid simulation software package. - Highlights: • A state space model extraction methodology based on graph-theoretic concepts. • An energy-based approach to consider multi-domain systems in a common framework. • Allow extraction of transparent (white-box) state space models automatically. • Reduced order models containing only independent state

On-line analysis of hydrogen and other parameters in the mineral and energy industries

International Nuclear Information System (INIS)

Sowerby, B.D.

1998-01-01

The objective of the project is the development and industrial application of nuclear and microwave techniques for the on-line determination of hydrogen, moisture and other parameters. This document presents progress with respect to the stated objectives. A laboratory feasibility study has been carried out on new and advanced neutron and gamma ray analysis systems for the direct on-conveyor belt analysis of ash in coal. Neutron inelastic scattering and thermal neutron capture gamma ray technique were used in development of an on-belt elemental analyser for cement industry. Microwave based technology has been developed for on-conveyor belt determination of moisture in coal. A fast neutron and gamma-ray transmission technique has been applied for on-belt determination of moisture in lump coke

Inverse modeling of hydrologic parameters using surface flux and runoff observations in the Community Land Model

Science.gov (United States)

Sun, Y.; Hou, Z.; Huang, M.; Tian, F.; Leung, L. Ruby

2013-12-01

This study demonstrates the possibility of inverting hydrologic parameters using surface flux and runoff observations in version 4 of the Community Land Model (CLM4). Previous studies showed that surface flux and runoff calculations are sensitive to major hydrologic parameters in CLM4 over different watersheds, and illustrated the necessity and possibility of parameter calibration. Both deterministic least-square fitting and stochastic Markov-chain Monte Carlo (MCMC)-Bayesian inversion approaches are evaluated by applying them to CLM4 at selected sites with different climate and soil conditions. The unknowns to be estimated include surface and subsurface runoff generation parameters and vadose zone soil water parameters. We find that using model parameters calibrated by the sampling-based stochastic inversion approaches provides significant improvements in the model simulations compared to using default CLM4 parameter values, and that as more information comes in, the predictive intervals (ranges of posterior distributions) of the calibrated parameters become narrower. In general, parameters that are identified to be significant through sensitivity analyses and statistical tests are better calibrated than those with weak or nonlinear impacts on flux or runoff observations. Temporal resolution of observations has larger impacts on the results of inverse modeling using heat flux data than runoff data. Soil and vegetation cover have important impacts on parameter sensitivities, leading to different patterns of posterior distributions of parameters at different sites. Overall, the MCMC-Bayesian inversion approach effectively and reliably improves the simulation of CLM under different climates and environmental conditions. Bayesian model averaging of the posterior estimates with different reference acceptance probabilities can smooth the posterior distribution and provide more reliable parameter estimates, but at the expense of wider uncertainty bounds.

Development of a macro-element by condensation, shown for the load categories of aircraft crash and seismic events, for soil-structure interaction in the case of flexible foundation

International Nuclear Information System (INIS)

Matthees, W.

1989-01-01

This report presents the results of a three-dimensional model developed for the analysis of soil-structure interaction problems. The realistic treatment of the stiffness for the foundation plate avoids the restriction of lumped parameter models for one-dimensional beam-models with a rigid plate or for multi-dimensional models with distributed lumped parameters. The soil-behaviour is defined by the condensation of a limited soil section, called macro-element. An improved matrix radiation damping comparable with lumped parameters is resultant from the condensation of viscous dampers, situated along the boundaries of the soil section. The finess of discretization is similar for the soil and for the structure. The method is presented in the time domain for a linear axisymmetric code with lumped mass having a consistent mass coupling of the macro-element. By application of the macro-element a realistic three-dimensional system may be analyzed with a reasonable numerical effort. (orig.) With 80 figs., 3 tabs [de

Parameter Estimation of the Thermal Network Model of a Machine Tool Spindle by Self-made Bluetooth Temperature Sensor Module

Directory of Open Access Journals (Sweden)

Yuan-Chieh Lo

2018-02-01

Full Text Available Thermal characteristic analysis is essential for machine tool spindles because sudden failures may occur due to unexpected thermal issue. This article presents a lumped-parameter Thermal Network Model (TNM and its parameter estimation scheme, including hardware and software, in order to characterize both the steady-state and transient thermal behavior of machine tool spindles. For the hardware, the authors develop a Bluetooth Temperature Sensor Module (BTSM which accompanying with three types of temperature-sensing probes (magnetic, screw, and probe. Its specification, through experimental test, achieves to the precision ±(0.1 + 0.0029|t| °C, resolution 0.00489 °C, power consumption 7 mW, and size Ø40 mm × 27 mm. For the software, the heat transfer characteristics of the machine tool spindle correlative to rotating speed are derived based on the theory of heat transfer and empirical formula. The predictive TNM of spindles was developed by grey-box estimation and experimental results. Even under such complicated operating conditions as various speeds and different initial conditions, the experiments validate that the present modeling methodology provides a robust and reliable tool for the temperature prediction with normalized mean square error of 99.5% agreement, and the present approach is transferable to the other spindles with a similar structure. For realizing the edge computing in smart manufacturing, a reduced-order TNM is constructed by Model Order Reduction (MOR technique and implemented into the real-time embedded system.

Effects of Geometry Design Parameters on the Static Strength and Dynamics for Spiral Bevel Gear

Directory of Open Access Journals (Sweden)

Zhiheng Feng

2017-01-01

Full Text Available Considering the geometry design parameters, a quasi-static mesh model of spiral bevel gears was established and the mesh characteristics were computed. Considering the time-varying effects of mesh points, mesh force, line-of-action vector, mesh stiffness, transmission error, friction force direction, and friction coefficient, a nonlinear lumped parameter dynamic model was developed for the spiral bevel gear pair. Based on the mesh model and the nonlinear dynamic model, the effects of main geometry parameters on the contact and bending strength were analyzed. Also, the effects on the dynamic mesh force and dynamic transmission error were investigated. Results show that higher value for the pressure angle, root fillet radius, and the ratio of tooth thickness tend to improve the contact and bending strength and to reduce the risk of tooth fracture. Improved gears have a better vibration performance in the targeted frequency range. Finally, bench tests for both types of spiral bevel gears were performed. Results show that the main failure mode is the tooth fracture and the life was increased a lot for the spiral bevel gears with improved geometry parameters compared to the original design.

Sensitivity analysis of respiratory parameter uncertainties: impact of criterion function form and constraints.

Science.gov (United States)

Lutchen, K R

1990-08-01

A sensitivity analysis based on weighted least-squares regression is presented to evaluate alternative methods for fitting lumped-parameter models to respiratory impedance data. The goal is to maintain parameter accuracy simultaneously with practical experiment design. The analysis focuses on predicting parameter uncertainties using a linearized approximation for joint confidence regions. Applications are with four-element parallel and viscoelastic models for 0.125- to 4-Hz data and a six-element model with separate tissue and airway properties for input and transfer impedance data from 2-64 Hz. The criterion function form was evaluated by comparing parameter uncertainties when data are fit as magnitude and phase, dynamic resistance and compliance, or real and imaginary parts of input impedance. The proper choice of weighting can make all three criterion variables comparable. For the six-element model, parameter uncertainties were predicted when both input impedance and transfer impedance are acquired and fit simultaneously. A fit to both data sets from 4 to 64 Hz could reduce parameter estimate uncertainties considerably from those achievable by fitting either alone. For the four-element models, use of an independent, but noisy, measure of static compliance was assessed as a constraint on model parameters. This may allow acceptable parameter uncertainties for a minimum frequency of 0.275-0.375 Hz rather than 0.125 Hz. This reduces data acquisition requirements from a 16- to a 5.33- to 8-s breath holding period. These results are approximations, and the impact of using the linearized approximation for the confidence regions is discussed.

Comprehensive distributed-parameters modeling and experimental validation of microcantilever-based biosensors with an application to ultrasmall biological species detection

International Nuclear Information System (INIS)

Faegh, Samira; Jalili, Nader

2013-01-01

Nanotechnological advancements have made a great contribution in developing label-free and highly sensitive biosensors. The detection of ultrasmall adsorbed masses has been enabled by such sensors which transduce molecular interaction into detectable physical quantities. More specifically, microcantilever-based biosensors have caught widespread attention for offering a label-free, highly sensitive and inexpensive platform for biodetection. Although there are a lot of studies investigating microcantilever-based sensors and their biological applications, a comprehensive mathematical modeling and experimental validation of such devices providing a closed form mathematical framework is still lacking. In almost all of the studies, a simple lumped-parameters model has been proposed. However, in order to have a precise biomechanical sensor, a comprehensive model is required being capable of describing all phenomena and dynamics of the biosensor. Therefore, in this study, an extensive distributed-parameters modeling framework is proposed for the piezoelectric microcantilever-based biosensor using different methodologies for the purpose of detecting an ultrasmall adsorbed mass over the microcantilever surface. An optimum modeling methodology is concluded and verified with the experiment. This study includes three main parts. In the first part, the Euler–Bernoulli beam theory is used to model the nonuniform piezoelectric microcantilever. Simulation results are obtained and presented. The same system is then modeled as a nonuniform rectangular plate. The simulation results are presented describing model's capability in the detection of an ultrasmall mass. Finally the last part presents the experimental validation verifying the modeling results. It was shown that plate modeling predicts the real situation with a degree of precision of 99.57% whereas modeling the system as an Euler–Bernoulli beam provides a 94.45% degree of precision. The detection of ultrasmall

Painless lump over the forehead which turned painful: an unusual presentation of hepatocellular carcinoma

Directory of Open Access Journals (Sweden)

S P Susheela

2015-05-01

Full Text Available Hepatocellular carcinoma (HCC is one of the most common malignancies and is known to most often present with symptomatology pertaining to local hepatic disease. Although HCC is known to metastasize to lungs, abdominal lymph nodes, adrenal glands and the vertebral column, it is rather rare to come across patients with skull metastasis. The manifestation of a solitary frontal bone metastasis leading to a painless lump over the forehead as the initial presenting feature of HCC is highly unusual. This case report pertains to a 40-year-old male patient who had initially observed a painless lump over his forehead that was gradually increasing in size over a span of 3 months. He sought medical attention when, after several months, the "painless lump" suddenly became painful. Investigations revealed the involvement of both the outer and the inner table of the frontal bone, and a biopsy revealed the histopathology to be that of HCC. On further investigation, he was found to have systemic disseminated disease involving both the left and right lungs and vertebrae and treatment was initiated with sorafenib. Despite an initial partial response, the patient subsequently succumbed to hepatic failure. This case report illustrates the fact that HCC can silently progress, and even lead to dissemination and distant metastases before becoming clinically evident.

ERM model analysis for adaptation to hydrological model errors

Science.gov (United States)

Baymani-Nezhad, M.; Han, D.

2018-05-01

Hydrological conditions are changed continuously and these phenomenons generate errors on flood forecasting models and will lead to get unrealistic results. Therefore, to overcome these difficulties, a concept called model updating is proposed in hydrological studies. Real-time model updating is one of the challenging processes in hydrological sciences and has not been entirely solved due to lack of knowledge about the future state of the catchment under study. Basically, in terms of flood forecasting process, errors propagated from the rainfall-runoff model are enumerated as the main source of uncertainty in the forecasting model. Hence, to dominate the exciting errors, several methods have been proposed by researchers to update the rainfall-runoff models such as parameter updating, model state updating, and correction on input data. The current study focuses on investigations about the ability of rainfall-runoff model parameters to cope with three types of existing errors, timing, shape and volume as the common errors in hydrological modelling. The new lumped model, the ERM model, has been selected for this study to evaluate its parameters for its use in model updating to cope with the stated errors. Investigation about ten events proves that the ERM model parameters can be updated to cope with the errors without the need to recalibrate the model.

Estimating Convection Parameters in the GFDL CM2.1 Model Using Ensemble Data Assimilation

Science.gov (United States)

Li, Shan; Zhang, Shaoqing; Liu, Zhengyu; Lu, Lv; Zhu, Jiang; Zhang, Xuefeng; Wu, Xinrong; Zhao, Ming; Vecchi, Gabriel A.; Zhang, Rong-Hua; Lin, Xiaopei

2018-04-01

Parametric uncertainty in convection parameterization is one major source of model errors that cause model climate drift. Convection parameter tuning has been widely studied in atmospheric models to help mitigate the problem. However, in a fully coupled general circulation model (CGCM), convection parameters which impact the ocean as well as the climate simulation may have different optimal values. This study explores the possibility of estimating convection parameters with an ensemble coupled data assimilation method in a CGCM. Impacts of the convection parameter estimation on climate analysis and forecast are analyzed. In a twin experiment framework, five convection parameters in the GFDL coupled model CM2.1 are estimated individually and simultaneously under both perfect and imperfect model regimes. Results show that the ensemble data assimilation method can help reduce the bias in convection parameters. With estimated convection parameters, the analyses and forecasts for both the atmosphere and the ocean are generally improved. It is also found that information in low latitudes is relatively more important for estimating convection parameters. This study further suggests that when important parameters in appropriate physical parameterizations are identified, incorporating their estimation into traditional ensemble data assimilation procedure could improve the final analysis and climate prediction.

Model parameter updating using Bayesian networks

International Nuclear Information System (INIS)

Treml, C.A.; Ross, Timothy J.

2004-01-01

This paper outlines a model parameter updating technique for a new method of model validation using a modified model reference adaptive control (MRAC) framework with Bayesian Networks (BNs). The model parameter updating within this method is generic in the sense that the model/simulation to be validated is treated as a black box. It must have updateable parameters to which its outputs are sensitive, and those outputs must have metrics that can be compared to that of the model reference, i.e., experimental data. Furthermore, no assumptions are made about the statistics of the model parameter uncertainty, only upper and lower bounds need to be specified. This method is designed for situations where a model is not intended to predict a complete point-by-point time domain description of the item/system behavior; rather, there are specific points, features, or events of interest that need to be predicted. These specific points are compared to the model reference derived from actual experimental data. The logic for updating the model parameters to match the model reference is formed via a BN. The nodes of this BN consist of updateable model input parameters and the specific output values or features of interest. Each time the model is executed, the input/output pairs are used to adapt the conditional probabilities of the BN. Each iteration further refines the inferred model parameters to produce the desired model output. After parameter updating is complete and model inputs are inferred, reliabilities for the model output are supplied. Finally, this method is applied to a simulation of a resonance control cooling system for a prototype coupled cavity linac. The results are compared to experimental data.

arXiv Statistical Analyses of Higgs- and Z-Portal Dark Matter Models

CERN Document Server

Ellis, John; Marzola, Luca; Raidal, Martti

2018-06-12

We perform frequentist and Bayesian statistical analyses of Higgs- and Z-portal models of dark matter particles with spin 0, 1/2 and 1. Our analyses incorporate data from direct detection and indirect detection experiments, as well as LHC searches for monojet and monophoton events, and we also analyze the potential impacts of future direct detection experiments. We find acceptable regions of the parameter spaces for Higgs-portal models with real scalar, neutral vector, Majorana or Dirac fermion dark matter particles, and Z-portal models with Majorana or Dirac fermion dark matter particles. In many of these cases, there are interesting prospects for discovering dark matter particles in Higgs or Z decays, as well as dark matter particles weighing $\\gtrsim 100$ GeV. Negative results from planned direct detection experiments would still allow acceptable regions for Higgs- and Z-portal models with Majorana or Dirac fermion dark matter particles.

Impedance function study for cylindrical tanks surrounded by an earthen embankment

International Nuclear Information System (INIS)

Houston, T.W.; Mertz, G.E.

1995-01-01

The Department of Energy (DOE) operates many which are used to store radioactive waste material. The original design of the tanks was often based on criteria which did not meet current seismic codes. As a result DOE is undertaking a comprehensive review of the adequacy of these structures to meet current seismic standards. This comprehensive review includes an evaluation of soil-structure interaction. One method available for performing soil structure interaction analyses of structures couples a discrete model of the structure to a lumped parameter model of the soil. This method requires the knowledge of the expected dynamic stiffness and damping functions of the rigid, massless structure resting on the soil. These are commonly referred to as the impedance functions. Lumped parameter analysis is cost effective for the surface and embedded structure cases where impedance functions are available in the literature. For a complex case with the structure located on the surface surrounded by an embankment, the impedance functions must be established prior to using a lumped parameter model approach. The present paper describes the development of horizontal impedance functions for the structure surrounded by an embankment which are developed using a finite element approach as implemented by SASSI. Impedance functions for vertical, torsional, and rocking degrees of freedom can be developed in a similar manner. These functions are easily incorporated into simple models which provide conceptual and physical insight to the response of structures. These models provide both a check of more sophisticated methods, and, due to their simplicity, permit assessment of a wide range of site and structural parameters that my affect the dynamic response of structural systems

PARAMETER ESTIMATION IN BREAD BAKING MODEL

Directory of Open Access Journals (Sweden)

Hadiyanto Hadiyanto

2012-05-01

Full Text Available Bread product quality is highly dependent to the baking process. A model for the development of product quality, which was obtained by using quantitative and qualitative relationships, was calibrated by experiments at a fixed baking temperature of 200°C alone and in combination with 100 W microwave powers. The model parameters were estimated in a stepwise procedure i.e. first, heat and mass transfer related parameters, then the parameters related to product transformations and finally product quality parameters. There was a fair agreement between the calibrated model results and the experimental data. The results showed that the applied simple qualitative relationships for quality performed above expectation. Furthermore, it was confirmed that the microwave input is most meaningful for the internal product properties and not for the surface properties as crispness and color. The model with adjusted parameters was applied in a quality driven food process design procedure to derive a dynamic operation pattern, which was subsequently tested experimentally to calibrate the model. Despite the limited calibration with fixed operation settings, the model predicted well on the behavior under dynamic convective operation and on combined convective and microwave operation. It was expected that the suitability between model and baking system could be improved further by performing calibration experiments at higher temperature and various microwave power levels.  Abstrak  PERKIRAAN PARAMETER DALAM MODEL UNTUK PROSES BAKING ROTI. Kualitas produk roti sangat tergantung pada proses baking yang digunakan. Suatu model yang telah dikembangkan dengan metode kualitatif dan kuantitaif telah dikalibrasi dengan percobaan pada temperatur 200oC dan dengan kombinasi dengan mikrowave pada 100 Watt. Parameter-parameter model diestimasi dengan prosedur bertahap yaitu pertama, parameter pada model perpindahan masa dan panas, parameter pada model transformasi, dan

A kinetic model for hydrodesulfurisation

Energy Technology Data Exchange (ETDEWEB)

Sau, M.; Narasimhan, C.S.L.; Verma, R.P. [Indian Oil Corporation Limited, Research and Development Centre, Faridabad (India)

1997-07-01

Due to stringent environmental considerations and related insistence on low sulfur fuels, hydrodesulfurisation has emerged as an important component of any refining scheme globally. The process is used ranging from Naphta/Kerosine hydrotreating to heavy oil hydrotreating. Processes such as Deep gas oil desulfurisation aiming at reduction of sulfur levels to less than 500 ppm have emerged as major players in the scenario. Hydrodesulfurisation (HDS) involves parallel desulfurisation of different organo-sulfur compounds present in the complex petroleum mixtures. In order to design, monitor, optimise and control the HDS reactor, it is necessary to have a detailed, yet simple model which follows the reaction chemistry accurately. In the present paper, a kinetic model is presented for HDS using continuum theory of lumping. The sulfur distribution in the reaction mixture is treated as continuum and parallel reaction networks are devised for kinetic modelling using continuum theory of lumping approach. The model based on the above approach follows the HDS chemistry reasonably well and hence the model parameters are almost feed invariant. Methods are also devised to incorporate heat and pressure effects into the model. The model has been validated based on commercial kero-HDS data. It is found that the model predictions agree with the experimental/commercial data. 17 refs.

Parameter sensitivity and identifiability for a biogeochemical model of hypoxia in the northern Gulf of Mexico

Science.gov (United States)

Local sensitivity analyses and identifiable parameter subsets were used to describe numerical constraints of a hypoxia model for bottom waters of the northern Gulf of Mexico. The sensitivity of state variables differed considerably with parameter changes, although most variables ...

Pressure oscillation delivery to the lung: Computer simulation of neonatal breathing parameters.

Science.gov (United States)

Al-Jumaily, Ahmed M; Reddy, Prasika I; Bold, Geoff T; Pillow, J Jane

2011-10-13

Preterm newborn infants may develop respiratory distress syndrome (RDS) due to functional and structural immaturity. A lack of surfactant promotes collapse of alveolar regions and airways such that newborns with RDS are subject to increased inspiratory effort and non-homogeneous ventilation. Pressure oscillation has been incorporated into one form of RDS treatment; however, how far it reaches various parts of the lung is still questionable. Since in-vivo measurement is very difficult if not impossible, mathematical modeling may be used as one way of assessment. Whereas many models of the respiratory system have been developed for adults, the neonatal lung remains essentially ill-described in mathematical models. A mathematical model is developed, which represents the first few generations of the tracheo-bronchial tree and the 5 lobes that make up the premature ovine lung. The elements of the model are derived using the lumped parameter approach and formulated in Simulink™ within the Matlab™ environment. The respiratory parameters at the airway opening compare well with those measured from experiments. The model demonstrates the ability to predict pressures, flows and volumes in the alveolar regions of a premature ovine lung. Copyright © 2011 Elsevier Ltd. All rights reserved.

Generalized model development for a cryo-adsorber and 1-D results for the isobaric refueling period

Energy Technology Data Exchange (ETDEWEB)

Kumar, V. Senthil [India Science Lab, General Motors Global R and D, Creator Building, International Technology Park, Bangalore 560066 (India); Kumar, Sudarshan [Chemical Sciences and Material Systems Lab, General Motors Global R and D, Warren Technical Center Campus, 30500 Mound Road, Warren, MI 48090 (United States)

2010-04-15

We have developed 3-D model equations for a cryo-adsorption hydrogen storage tank, where the energy balance accommodates the temperature and pressure variation of all the thermodynamic properties. We then reduce the 3-D model to the 1-D isobaric system and study the isobaric refueling period, for simplified geometry and charging conditions. The hydrogen capacity evolution predicted by the 1-D axial bed model is significantly different than that predicted by the lumped-parameter model because of the presence of sharp temperature gradients during refueling. The 1-D model predicts a higher hydrogen capacity than the lumped-parameter model. This observation can be rationalized by the fact that a bed with temperature gradients on equilibration should desorb gas, whenever the adsorbed phase entropy is lower than the gas phase entropy. The 1-D analysis of the isobaric refueling period does not show any significant difference in hydrogen capacity evolution among the axial, single and multicartridge annular bed designs. Hence, a multicartridge annular design, though giving a slightly lower pressure drop, does not offer any heat and mass transfer enhancement over the single cartridge design. And, the single cartridge annular design appears to be optimal. (author)

The lumped heat capacity method applied to target heating

OpenAIRE

Rickards, J.

2013-01-01

The temperature of metal samples was measured while they were bombarded by the beam from the a particle accelerator. The evolution of the temperature with time can be explained using the lumped heat capacity method of heat transfer. A strong dependence on the type of mounting was found. Se midió la temperatura de muestras metálicas al ser bombardeadas por el haz de iones del Acelerador Pelletron del Instituto de Física. La evolución de la temperatura con el tiempo se puede explicar usando ...

Probing lumps of wee partons in deep inelastic scattering

International Nuclear Information System (INIS)

Buchmueller, W.

1994-06-01

Recently, the ZEUS collaboration has reported on several remarkable properties of events with a large rapidity gap in deep inelastic scattering. We suggest that the mechanism underlying these events is the scattering of electrons off lumps of wee partons inside the proton. Based on an effective lagrangian approach the Q 2 -, x- and W-distributions are evaluated. For sufficiently small invariant mass of the detected hadronic system, the mechanism implies leading twist behaviour. The x- and W-distributions are determined by the Lipatov exponent which governs the behaviour of parton densities at small x. (orig.)

Health monitoring system for transmission shafts based on adaptive parameter identification

Science.gov (United States)

Souflas, I.; Pezouvanis, A.; Ebrahimi, K. M.

2018-05-01

A health monitoring system for a transmission shaft is proposed. The solution is based on the real-time identification of the physical characteristics of the transmission shaft i.e. stiffness and damping coefficients, by using a physical oriented model and linear recursive identification. The efficacy of the suggested condition monitoring system is demonstrated on a prototype transient engine testing facility equipped with a transmission shaft capable of varying its physical properties. Simulation studies reveal that coupling shaft faults can be detected and isolated using the proposed condition monitoring system. Besides, the performance of various recursive identification algorithms is addressed. The results of this work recommend that the health status of engine dynamometer shafts can be monitored using a simple lumped-parameter shaft model and a linear recursive identification algorithm which makes the concept practically viable.

Statistical Analysis of Input Parameters Impact on the Modelling of Underground Structures

Directory of Open Access Journals (Sweden)

M. Hilar

2008-01-01

Full Text Available The behaviour of a geomechanical model and its final results are strongly affected by the input parameters. As the inherent variability of rock mass is difficult to model, engineers are frequently forced to face the question “Which input values should be used for analyses?” The correct answer to such a question requires a probabilistic approach, considering the uncertainty of site investigations and variation in the ground. This paper describes the statistical analysis of input parameters for FEM calculations of traffic tunnels in the city of Prague. At the beginning of the paper, the inaccuracy in the geotechnical modelling is discussed. In the following part the Fuzzy techniques are summarized, including information about an application of the Fuzzy arithmetic on the shotcrete parameters. The next part of the paper is focused on the stochastic simulation – Monte Carlo Simulation is briefly described, Latin Hypercubes method is described more in details. At the end several practical examples are described: statistical analysis of the input parameters on the numerical modelling of the completed Mrázovka tunnel (profile West Tunnel Tube km 5.160 and modelling of the constructed tunnel Špejchar – Pelc Tyrolka. 

Acute lymphoblastic leukemia presenting as a breast lump: A report of two cases

Directory of Open Access Journals (Sweden)

Syed Besina

2013-01-01

Full Text Available Extra-medullary leukemic infiltration of the breast by acute lymphoblastic leukemia (ALL is very rare. We report two cases of ALL presenting as breast masses and diagnosed on fine-needle aspiration (FNA. Our first patient, a post-partum 30-year-old female, developed bilateral breast lumps in her last trimester of pregnancy and complained of easy fatigability. Our second patient, a 14-year-old girl, presented with a right-breast lump of 1-week duration. She had received treatment for ALL 1 year back and had been in complete remission for the last 1 year. FNA of the breast nodules done in both the cases revealed diffuse infiltration by lymphoblasts. Subsequent hematological investigations confirmed bone marrow involvement by ALL in the first case and extra-medullary relapse in the second case. Fine-needle aspiration cytology (FNAC is an easy and cost effective method for the early diagnosis of metastatic leukemic infiltration, avoiding unnecessary excisional biopsies in such cases.

Some error estimates for the lumped mass finite element method for a parabolic problem

KAUST Repository

Chatzipantelidis, P.; Lazarov, R. D.; Thomé e, V.

2012-01-01

for the standard Galerkin method carry over to the lumped mass method whereas nonsmooth initial data estimates require special assumptions on the triangulation. We also discuss the application to time discretization by the backward Euler and Crank-Nicolson methods

Operational use of distributed hydrological models. Experiences and challenges at a Norwegian hydropower company (Agder Energi).

Science.gov (United States)

Viggo Matheussen, Bernt; Andresen, Arne; Weisser, Claudia

2014-05-01

The Scandinavian hydropower industry has traditionally adopted the lumped conceptual hydrological model - HBV, as the tool for producing forecasts of inflows and mountain snow packs. Such forecasting systems - based on lumped conceptual models - have several drawbacks. Firstly, a lumped model does not produce spatial data, and comparisons with remote sensed snow cover data (which are now available) are complicated. Secondly, several climate parameters such as wind speed are now becoming more available and can potentially improve forecasts due to improved estimates of precipitation gauge efficiency, and more physically correct calculation of turbulent heat fluxes. At last, when the number of catchments increases, it is cumbersome and slow to run multiple hydrology models compared to running one model for all catchments. With the drawbacks of the lumped hydrology models in mind, and with inspiration from other forecasting systems using distributed models, Agder Energy decided to develop a forecasting system applying a physically based distributed model. In this paper we describe an operational inflow and snowpack forecast system developed for the Scandinavian mountain range. The system applies a modern macroscale land surface hydrology model (VIC) which in combination with historical climate data and weather predictions can be used to produce both short-term, and seasonal forecasts of inflow and mountain snowpack. Experiences with the forecast system are illustrated using results from individual subcatchments as well as aggregated regional forecasts of inflow and snowpack. Conversion of water volumes into effective energy inflow are also presented and compared to data from the Nordic hydropower system. Further on, we document several important "lessons-learned" that may be of interest to the hydrological research community. Specifically a semi-automatic data cleansing system combining spatial and temporal visualization techniques with statistical procedures are

Photovoltaic module parameters acquisition model

Energy Technology Data Exchange (ETDEWEB)

Cibira, Gabriel, E-mail: cibira@lm.uniza.sk; Koščová, Marcela, E-mail: mkoscova@lm.uniza.sk

2014-09-01

Highlights: • Photovoltaic five-parameter model is proposed using Matlab{sup ®} and Simulink. • The model acquisits input sparse data matrix from stigmatic measurement. • Computer simulations lead to continuous I–V and P–V characteristics. • Extrapolated I–V and P–V characteristics are in hand. • The model allows us to predict photovoltaics exploitation in different conditions. - Abstract: This paper presents basic procedures for photovoltaic (PV) module parameters acquisition using MATLAB and Simulink modelling. In first step, MATLAB and Simulink theoretical model are set to calculate I–V and P–V characteristics for PV module based on equivalent electrical circuit. Then, limited I–V data string is obtained from examined PV module using standard measurement equipment at standard irradiation and temperature conditions and stated into MATLAB data matrix as a reference model. Next, the theoretical model is optimized to keep-up with the reference model and to learn its basic parameters relations, over sparse data matrix. Finally, PV module parameters are deliverable for acquisition at different realistic irradiation, temperature conditions as well as series resistance. Besides of output power characteristics and efficiency calculation for PV module or system, proposed model validates computing statistical deviation compared to reference model.

Photovoltaic module parameters acquisition model

International Nuclear Information System (INIS)

Cibira, Gabriel; Koščová, Marcela

2014-01-01

Highlights: • Photovoltaic five-parameter model is proposed using Matlab ® and Simulink. • The model acquisits input sparse data matrix from stigmatic measurement. • Computer simulations lead to continuous I–V and P–V characteristics. • Extrapolated I–V and P–V characteristics are in hand. • The model allows us to predict photovoltaics exploitation in different conditions. - Abstract: This paper presents basic procedures for photovoltaic (PV) module parameters acquisition using MATLAB and Simulink modelling. In first step, MATLAB and Simulink theoretical model are set to calculate I–V and P–V characteristics for PV module based on equivalent electrical circuit. Then, limited I–V data string is obtained from examined PV module using standard measurement equipment at standard irradiation and temperature conditions and stated into MATLAB data matrix as a reference model. Next, the theoretical model is optimized to keep-up with the reference model and to learn its basic parameters relations, over sparse data matrix. Finally, PV module parameters are deliverable for acquisition at different realistic irradiation, temperature conditions as well as series resistance. Besides of output power characteristics and efficiency calculation for PV module or system, proposed model validates computing statistical deviation compared to reference model

The development of thermal models for a UF6 transport container in a fully engulfing fire

International Nuclear Information System (INIS)

Lomas, J.; Clayton, D.G.

1993-01-01

This paper describes the recent development work on a lumped-parameter model known as BURST3 created by BNFL to examine the physics of the heating problem. The predictions of this model were compared with the results obtained by Mallett in 1965, in which small (3.5, 5 and 8 inch diameter) cylinders were exposed to a fire. In general, the comparison is good; however there are some differences - particularly on the speed of response of the wall temperature to the heating from the fire. The model was further modified to allow conditions of partial and full insulation to be investigated. The partially insulated condition simulates the Japanese proposal to insulate the ends of the container only, leaving the cylinder bare between the stiffening rings. The results obtained with our modified model support the predictions of Abe et al that the partially-insulated cylinder will survive the fire test. The analysis of a completely insulated container has indicated that a minimal thickness of insulation provides sufficient protection to allow survival in the fire test. A discussion of additional improvements to the lumped-parameter model are presented. (J.P.N.)

Comparison with Russian analyses of meteor impact

Energy Technology Data Exchange (ETDEWEB)

Canavan, G.H.

1997-06-01

The inversion model for meteor impacts is used to discuss Russian analyses and compare principal results. For common input parameters, the models produce consistent estimates of impactor parameters. Directions for future research are discussed and prioritized.

SPOTting model parameters using a ready-made Python package

Science.gov (United States)

Houska, Tobias; Kraft, Philipp; Breuer, Lutz

2015-04-01

The selection and parameterization of reliable process descriptions in ecological modelling is driven by several uncertainties. The procedure is highly dependent on various criteria, like the used algorithm, the likelihood function selected and the definition of the prior parameter distributions. A wide variety of tools have been developed in the past decades to optimize parameters. Some of the tools are closed source. Due to this, the choice for a specific parameter estimation method is sometimes more dependent on its availability than the performance. A toolbox with a large set of methods can support users in deciding about the most suitable method. Further, it enables to test and compare different methods. We developed the SPOT (Statistical Parameter Optimization Tool), an open source python package containing a comprehensive set of modules, to analyze and optimize parameters of (environmental) models. SPOT comes along with a selected set of algorithms for parameter optimization and uncertainty analyses (Monte Carlo, MC; Latin Hypercube Sampling, LHS; Maximum Likelihood, MLE; Markov Chain Monte Carlo, MCMC; Scuffled Complex Evolution, SCE-UA; Differential Evolution Markov Chain, DE-MCZ), together with several likelihood functions (Bias, (log-) Nash-Sutcliff model efficiency, Correlation Coefficient, Coefficient of Determination, Covariance, (Decomposed-, Relative-, Root-) Mean Squared Error, Mean Absolute Error, Agreement Index) and prior distributions (Binomial, Chi-Square, Dirichlet, Exponential, Laplace, (log-, multivariate-) Normal, Pareto, Poisson, Cauchy, Uniform, Weibull) to sample from. The model-independent structure makes it suitable to analyze a wide range of applications. We apply all algorithms of the SPOT package in three different case studies. Firstly, we investigate the response of the Rosenbrock function, where the MLE algorithm shows its strengths. Secondly, we study the Griewank function, which has a challenging response surface for

Information on Hydrologic Conceptual Models, Parameters, Uncertainty Analysis, and Data Sources for Dose Assessments at Decommissioning Sites

International Nuclear Information System (INIS)

Meyer, Philip D.; Gee, Glendon W.; Nicholson, Thomas J.

1999-01-01

This report addresses issues related to the analysis of uncertainty in dose assessments conducted as part of decommissioning analyses. The analysis is limited to the hydrologic aspects of the exposure pathway involving infiltration of water at the ground surface, leaching of contaminants, and transport of contaminants through the groundwater to a point of exposure. The basic conceptual models and mathematical implementations of three dose assessment codes are outlined along with the site-specific conditions under which the codes may provide inaccurate, potentially nonconservative results. In addition, the hydrologic parameters of the codes are identified and compared. A methodology for parameter uncertainty assessment is outlined that considers the potential data limitations and modeling needs of decommissioning analyses. This methodology uses generic parameter distributions based on national or regional databases, sensitivity analysis, probabilistic modeling, and Bayesian updating to incorporate site-specific information. Data sources for best-estimate parameter values and parameter uncertainty information are also reviewed. A follow-on report will illustrate the uncertainty assessment methodology using decommissioning test cases

Information on Hydrologic Conceptual Models, Parameters, Uncertainty Analysis, and Data Sources for Dose Assessments at Decommissioning Sites

International Nuclear Information System (INIS)

Meyer D, Philip; Gee W, Glendon

2000-01-01

This report addresses issues related to the analysis of uncertainty in dose assessments conducted as part of decommissioning analyses. The analysis is limited to the hydrologic aspects of the exposure pathway involving infiltration of water at the ground surface, leaching of contaminants, and transport of contaminants through the groundwater to a point of exposure. The basic conceptual models and mathematical implementations of three dose assessment codes are outlined along with the site-specific conditions under which the codes may provide inaccurate, potentially nonconservative results. In addition, the hydrologic parameters of the codes are identified and compared. A methodology for parameter uncertainty assessment is outlined that considers the potential data limitations and modeling needs of decommissioning analyses. This methodology uses generic parameter distributions based on national or regional databases, sensitivity analysis, probabilistic modeling, and Bayesian updating to incorporate site-specific information. Data sources for best-estimate parameter values and parameter uncertainty information are also reviewed. A follow-on report will illustrate the uncertainty assessment methodology using decommissioning test cases

Prediction of gasoline yield in a fluid catalytic cracking (FCC riser using k-epsilon turbulence and 4-lump kinetic models: A computational fluid dynamics (CFD approach

Directory of Open Access Journals (Sweden)

Muhammad Ahsan

2015-07-01

Full Text Available Fluid catalytic cracking (FCC is an essential process for the conversion of gas oil to gasoline. This study is an effort to model the phenomenon numerically using commercial computational fluid dynamics (CFD software, heavy density catalyst and 4-lump kinetic model. Geometry, boundary conditions and dimensions of industrial riser for catalytic cracking unit are conferred for 2D simulation using commercial CFD code FLUENT 6.3. Continuity, momentum, energy and species transport equations, applicable to two phase solid and gas flow, are used to simulate the physical phenomenon as efficient as possible. This study implements and predicts the use of the granular Eulerian multiphase model with species transport. Time accurate transient problem is solved with the prediction of mass fraction profiles of gas oil, gasoline, light gas and coke. The output curves demonstrate the breaking of heavy hydrocarbon in the presence of catalyst. An approach proposed in this study shows good agreement with the experimental and numerical data available in the literature.

Structural identifiability analyses of candidate models for in vitro Pitavastatin hepatic uptake.

Science.gov (United States)

Grandjean, Thomas R B; Chappell, Michael J; Yates, James W T; Evans, Neil D

2014-05-01

In this paper a review of the application of four different techniques (a version of the similarity transformation approach for autonomous uncontrolled systems, a non-differential input/output observable normal form approach, the characteristic set differential algebra and a recent algebraic input/output relationship approach) to determine the structural identifiability of certain in vitro nonlinear pharmacokinetic models is provided. The Organic Anion Transporting Polypeptide (OATP) substrate, Pitavastatin, is used as a probe on freshly isolated animal and human hepatocytes. Candidate pharmacokinetic non-linear compartmental models have been derived to characterise the uptake process of Pitavastatin. As a prerequisite to parameter estimation, structural identifiability analyses are performed to establish that all unknown parameters can be identified from the experimental observations available. Copyright © 2013. Published by Elsevier Ireland Ltd.

Linear least squares compartmental-model-independent parameter identification in PET

International Nuclear Information System (INIS)

Thie, J.A.; Smith, G.T.; Hubner, K.F.

1997-01-01

A simplified approach involving linear-regression straight-line parameter fitting of dynamic scan data is developed for both specific and nonspecific models. Where compartmental-model topologies apply, the measured activity may be expressed in terms of: its integrals, plasma activity and plasma integrals -- all in a linear expression with macroparameters as coefficients. Multiple linear regression, as in spreadsheet software, determines parameters for best data fits. Positron emission tomography (PET)-acquired gray-matter images in a dynamic scan are analyzed: both by this method and by traditional iterative nonlinear least squares. Both patient and simulated data were used. Regression and traditional methods are in expected agreement. Monte-Carlo simulations evaluate parameter standard deviations, due to data noise, and much smaller noise-induced biases. Unique straight-line graphical displays permit visualizing data influences on various macroparameters as changes in slopes. Advantages of regression fitting are: simplicity, speed, ease of implementation in spreadsheet software, avoiding risks of convergence failures or false solutions in iterative least squares, and providing various visualizations of the uptake process by straight line graphical displays. Multiparameter model-independent analyses on lesser understood systems is also made possible

Sampling and sensitivity analyses tools (SaSAT for computational modelling

Directory of Open Access Journals (Sweden)

Wilson David P

2008-02-01

Full Text Available Abstract SaSAT (Sampling and Sensitivity Analysis Tools is a user-friendly software package for applying uncertainty and sensitivity analyses to mathematical and computational models of arbitrary complexity and context. The toolbox is built in Matlab®, a numerical mathematical software package, and utilises algorithms contained in the Matlab® Statistics Toolbox. However, Matlab® is not required to use SaSAT as the software package is provided as an executable file with all the necessary supplementary files. The SaSAT package is also designed to work seamlessly with Microsoft Excel but no functionality is forfeited if that software is not available. A comprehensive suite of tools is provided to enable the following tasks to be easily performed: efficient and equitable sampling of parameter space by various methodologies; calculation of correlation coefficients; regression analysis; factor prioritisation; and graphical output of results, including response surfaces, tornado plots, and scatterplots. Use of SaSAT is exemplified by application to a simple epidemic model. To our knowledge, a number of the methods available in SaSAT for performing sensitivity analyses have not previously been used in epidemiological modelling and their usefulness in this context is demonstrated.

Distributed ESO based cooperative tracking control for high-order nonlinear multiagent systems with lumped disturbance and application in multi flight simulators systems.

Science.gov (United States)

Cong, Zhang

2018-03-01

Based on extended state observer, a novel and practical design method is developed to solve the distributed cooperative tracking problem of higher-order nonlinear multiagent systems with lumped disturbance in a fixed communication topology directed graph. The proposed method is designed to guarantee all the follower nodes ultimately and uniformly converge to the leader node with bounded residual errors. The leader node, modeled as a higher-order non-autonomous nonlinear system, acts as a command generator giving commands only to a small portion of the networked follower nodes. Extended state observer is used to estimate the local states and lumped disturbance of each follower node. Moreover, each distributed controller can work independently only requiring the relative states and/or the estimated relative states information between itself and its neighbors. Finally an engineering application of multi flight simulators systems is demonstrated to test and verify the effectiveness of the proposed algorithm. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Modal analysis of human body vibration model for Indian subjects under sitting posture.

Science.gov (United States)

Singh, Ishbir; Nigam, S P; Saran, V H

2015-01-01

Need and importance of modelling in human body vibration research studies are well established. The study of biodynamic responses of human beings can be classified into experimental and analytical methods. In the past few decades, plenty of mathematical models have been developed based on the diverse field measurements to describe the biodynamic responses of human beings. In this paper, a complete study on lumped parameter model derived from 50th percentile anthropometric data for a seated 54- kg Indian male subject without backrest support under free un-damped conditions has been carried out considering human body segments to be of ellipsoidal shape. Conventional lumped parameter modelling considers the human body as several rigid masses interconnected by springs and dampers. In this study, concept of mass of interconnecting springs has been incorporated and eigenvalues thus obtained are found to be closer to the values reported in the literature. Results obtained clearly establish decoupling of vertical and fore-and-aft oscillations. The mathematical modelling of human body vibration studies help in validating the experimental investigations for ride comfort of a sitting subject. This study clearly establishes the decoupling of vertical and fore-and-aft vibrations and helps in better understanding of possible human response to single and multi-axial excitations.

Finding and testing network communities by lumped Markov chains.

Science.gov (United States)

Piccardi, Carlo

2011-01-01

Identifying communities (or clusters), namely groups of nodes with comparatively strong internal connectivity, is a fundamental task for deeply understanding the structure and function of a network. Yet, there is a lack of formal criteria for defining communities and for testing their significance. We propose a sharp definition that is based on a quality threshold. By means of a lumped Markov chain model of a random walker, a quality measure called "persistence probability" is associated to a cluster, which is then defined as an "α-community" if such a probability is not smaller than α. Consistently, a partition composed of α-communities is an "α-partition." These definitions turn out to be very effective for finding and testing communities. If a set of candidate partitions is available, setting the desired α-level allows one to immediately select the α-partition with the finest decomposition. Simultaneously, the persistence probabilities quantify the quality of each single community. Given its ability in individually assessing each single cluster, this approach can also disclose single well-defined communities even in networks that overall do not possess a definite clusterized structure.

Finding and testing network communities by lumped Markov chains.

Directory of Open Access Journals (Sweden)

Carlo Piccardi

Full Text Available Identifying communities (or clusters, namely groups of nodes with comparatively strong internal connectivity, is a fundamental task for deeply understanding the structure and function of a network. Yet, there is a lack of formal criteria for defining communities and for testing their significance. We propose a sharp definition that is based on a quality threshold. By means of a lumped Markov chain model of a random walker, a quality measure called "persistence probability" is associated to a cluster, which is then defined as an "α-community" if such a probability is not smaller than α. Consistently, a partition composed of α-communities is an "α-partition." These definitions turn out to be very effective for finding and testing communities. If a set of candidate partitions is available, setting the desired α-level allows one to immediately select the α-partition with the finest decomposition. Simultaneously, the persistence probabilities quantify the quality of each single community. Given its ability in individually assessing each single cluster, this approach can also disclose single well-defined communities even in networks that overall do not possess a definite clusterized structure.

Analysis of the reactivity of sulphur compounds in petroleum cuts: kinetics and modelling of hydro-treating; Analyse de la reactivite des composes soufres dans les coupes petrolieres: cinetique et modelisation de l'hydrotraitement

Energy Technology Data Exchange (ETDEWEB)

Lopez Garcia, C

2000-12-01

The study of the hydro-treating of middle distillates comprised the following steps: - Identification and reactivity study of the sulphur compounds present in these petroleum cuts; - Modelling of the process by a chemical kinetic approach. The hydro-treating of middle distillates is a refining process that allows elimination of organic compounds containing sulphur, nitrogen, oxygen and metals. The process also hydrogenates the aromatic compounds providing improved cetane index gas-oils while respecting the regulations that severely limit the content of sulphur compounds. The extension and the improvement of a kinetic model for the hydro-treating of LCO gas-oils (light cycle oil gas-oils) are presented in this work. In order to improve the hydro-desulfurization model predictions, a detailed identification of the sulphur compounds contained in LCO gas-oils was carried out using gas chromatography with a sulphur chemiluminescence detector (GC-SCD). The most refractory sulphur compounds (alkyl-di-benzothiophenes) were identified and lumped into different families. Based on a lumped reaction scheme with a Langmuir-Hinshelwood representation, the model takes into account the influence of temperature, total pressure and hydrogen sulphide partial pressure on the reaction rates for hydro-desulfurization, hydro-denitrogenation and hydro-de-aromatization. The model parameter estimation was based on experiments that were carried out on a micro-pilot unit using an industrial sulfided NiMo/Al{sub 2}O{sub 3} catalyst and LCO feedstocks. The analytical study of the sulphur compounds was also extended to the case of straight run gas-oils (SR). For these feedstocks, a method using high-resolution mass spectrometry coupled with gas chromatography (GC-HRMS) was developed. In this way, the kinetic model can now be extended for the SR gas-oil hydro-treating or for LCO-SR mixtures. (author)

A Size Reduction Technique for Mobile Phone PIFA Antennas Using Lumped Inductors

DEFF Research Database (Denmark)

Thaysen, Jesper; Jakobsen, Kaj Bjarne

2005-01-01

A size reduction technique for the planar inverted-F antenna (PIFA) is presented. An 18 nH lumped inductor is used in addition to a small 0.3 cm3 PIFA. The PIFA is located on dielectric foam, 5 mm above a 40 mm × 100 mm ground plane. It is possible to reduce the center frequency (|S11|min) by 33 ...

Experimental evaluation of a modal parameter based system identification procedure

Science.gov (United States)

Yu, Minli; Feng, Ningsheng; Hahn, Eric J.

2016-02-01

Correct modelling of the foundation of a rotor bearing foundation system (RBFS) is an invaluable asset for the balancing and efficient running of turbomachinery. Numerical experiments have shown that a modal parameter based identification approach could be feasible for this purpose but there is a lack of experimental verification of the suitability of such a modal approach for even the simplest systems. In this paper the approach is tested on a simple experimental rig comprising a clamped horizontal bar with lumped masses. It is shown that apart from damping, the proposed approach can identify reasonably accurately the relevant modal parameters of the rig; and that the resulting equivalent system can predict reasonably well the frequency response of the rig. Hence, the proposed approach shows promise but further testing is required, since application to identifying the foundation of an RBFS involves the additional problem of accurately obtaining the force excitation from motion measurements.

Control oriented modeling of ejector in anode gas recirculation solid oxygen fuel cell systems

International Nuclear Information System (INIS)

Zhu Yinhai; Li Yanzhong; Cai Wenjian

2011-01-01

A one-equation model is proposed for fuel ejector in anode gas recirculation solid oxide fuel cell (SOFC) system. Firstly, the fundamental governing equations are established by employing the thermodynamic, fluid dynamic principles and chemical constraints inside the ejector; secondly, the one-equation model is derived by using the parameter analysis and lumped-parameter method. Finally, the computational fluid dynamics (CFD) technique is employed to obtain the source data for determining the model parameters. The effectiveness of the model is studied under a wide range of operation conditions. The effect of ejector performance on the anode gas recirculation SOFC system is also discussed. The presented model, which only contains four constant parameters, is useful in real-time control and optimization of fuel ejector in the anode gas recirculation SOFC system.

Determination of crack morphology parameters from service failures for leak-rate analyses

Energy Technology Data Exchange (ETDEWEB)

Wilkowski, G.; Ghadiali, N.; Paul, D. [Battelle Memorial Institute, Columbus, OH (United States)] [and others

1997-04-01

In leak-rate analyses described in the literature, the crack morphology parameters are typically not well agreed upon by different investigators. This paper presents results on a review of crack morphology parameters determined from examination of service induced cracks. Service induced cracks were found to have a much more tortuous flow path than laboratory induced cracks due to crack branching associated with the service induced cracks. Several new parameters such as local and global surface roughnesses, as well as local and global number of turns were identified. The effect of each of these parameters are dependent on the crack-opening displacement. Additionally, the crack path is typically assumed to be straight through the pipe thickness, but the service data show that the flow path can be longer due to the crack following a fusion line, and/or the number of turns, where the number of turns in the past were included as a pressure drop term due to the turns, but not the longer flow path length. These parameters were statistically evaluated for fatigue cracks in air, corrosion-fatigue, IGSCC, and thermal fatigue cracks. A refined version of the SQUIRT leak-rate code was developed to account for these variables. Sample calculations are provided in this paper that show how the crack size can vary for a given leak rate and the statistical variation of the crack morphology parameters.

Parameters identification of photovoltaic models using an improved JAYA optimization algorithm

International Nuclear Information System (INIS)

Yu, Kunjie; Liang, J.J.; Qu, B.Y.; Chen, Xu; Wang, Heshan

2017-01-01

Highlights: • IJAYA algorithm is proposed to identify the PV model parameters efficiently. • A self-adaptive weight is introduced to purposefully adjust the search process. • Experience-based learning strategy is developed to enhance the population diversity. • Chaotic learning method is proposed to refine the quality of the best solution. • IJAYA features the superior performance in identifying parameters of PV models. - Abstract: Parameters identification of photovoltaic (PV) models based on measured current-voltage characteristic curves is significant for the simulation, evaluation, and control of PV systems. To accurately and reliably identify the parameters of different PV models, an improved JAYA (IJAYA) optimization algorithm is proposed in the paper. In IJAYA, a self-adaptive weight is introduced to adjust the tendency of approaching the best solution and avoiding the worst solution at different search stages, which enables the algorithm to approach the promising area at the early stage and implement the local search at the later stage. Furthermore, an experience-based learning strategy is developed and employed randomly to maintain the population diversity and enhance the exploration ability. A chaotic elite learning method is proposed to refine the quality of the best solution in each generation. The proposed IJAYA is used to solve the parameters identification problems of different PV models, i.e., single diode, double diode, and PV module. Comprehensive experiment results and analyses indicate that IJAYA can obtain a highly competitive performance compared with other state-of-the-state algorithms, especially in terms of accuracy and reliability.

Technical Approach for Determining Key Parameters Needed for Modeling the Performance of Cast Stone for the Integrated Disposal Facility Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

Yabusaki, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rockhold, Mark L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-03-30

the critical link between the short-term understanding from laboratory and field tests, and the prediction of repository performance over repository time frames and scales. One common recommendation is that experiments be designed to permit the appropriate scaling in the models. There is a large contrast in the physical and chemical properties between the Cast Stone waste package and the IDF backfill and surrounding sediments. Cast Stone exhibits low permeability, high tortuosity, low carbonate, high pH, and low Eh whereas the backfill and native sediments have high permeability, low tortuosity, high carbonate, circumneutral pH, and high Eh. These contrasts have important implications for flow, transport, and reactions across the Cast Stone – backfill interface. Over time with transport across the interface and subsequent reactions, the sharp geochemical contrast will blur and there will be a range of spatially-distributed conditions. In general, COC mobility and transport will be sensitive to these geochemical variations, which also include physical changes in porosity and permeability from mineral reactions. Therefore, PA modeling must address processes, properties, and conditions that alter the physical and chemical controls on COC transport in the cementitious waste forms over time. Section 2 of this document reviews past Hanford PAs and SRS Saltstone PAs, which to date have mostly relied on the lumped parameter COC release conceptual models for TSPA predictions, and provides some details on the chosen values for the lumped parameters. Section 3 provides more details on the hierarchical modeling strategy and processes and mechanisms that control COC release. Section 4 summarizes and lists the key parameters for which numerical values are needed to perform PAs. Section 5 provides brief summaries of the methods used to measure the needed parameters and references to get more details.

The importance of proper feedback modeling in HWR

Energy Technology Data Exchange (ETDEWEB)

Saphier, D; Gorelik, Z; Shapira, M [Israel Atomic Energy Commission, Yavne (Israel). Soreq Nuclear Research Center

1996-12-01

The DSNP simulation language was applied to study the effect of different modeling approximations of feedback phenomena in nuclear power plants. The different methods to model the feedback effects are presented and discussed. It is shown that HWR`s are most sensitive to the correct modeling since the usually have at least three feedback effects acting at different time scales, and to achieve correct kinetics a one dimensional representation is needed with correct modeling of the in core time delays. The simulation methodology of lumped parameters and one dimensional models using the DSNP simulation language is presented (authors).

The importance of proper feedback modeling in HWR

International Nuclear Information System (INIS)

Saphier, D.; Gorelik, Z.; Shapira, M.

1996-01-01

The DSNP simulation language was applied to study the effect of different modeling approximations of feedback phenomena in nuclear power plants. The different methods to model the feedback effects are presented and discussed. It is shown that HWR's are most sensitive to the correct modeling since the usually have at least three feedback effects acting at different time scales, and to achieve correct kinetics a one dimensional representation is needed with correct modeling of the in core time delays. The simulation methodology of lumped parameters and one dimensional models using the DSNP simulation language is presented (authors)

Analysis of the reactivity of sulphur compounds in petroleum cuts: kinetics and modelling of hydro-treating; Analyse de la reactivite des composes soufres dans les coupes petrolieres: cinetique et modelisation de l'hydrotraitement

Energy Technology Data Exchange (ETDEWEB)

Lopez Garcia, C.

2000-12-01

The study of the hydro-treating of middle distillates comprised the following steps: - Identification and reactivity study of the sulphur compounds present in these petroleum cuts; - Modelling of the process by a chemical kinetic approach. The hydro-treating of middle distillates is a refining process that allows elimination of organic compounds containing sulphur, nitrogen, oxygen and metals. The process also hydrogenates the aromatic compounds providing improved cetane index gas-oils while respecting the regulations that severely limit the content of sulphur compounds. The extension and the improvement of a kinetic model for the hydro-treating of LCO gas-oils (light cycle oil gas-oils) are presented in this work. In order to improve the hydro-desulfurization model predictions, a detailed identification of the sulphur compounds contained in LCO gas-oils was carried out using gas chromatography with a sulphur chemiluminescence detector (GC-SCD). The most refractory sulphur compounds (alkyl-di-benzothiophenes) were identified and lumped into different families. Based on a lumped reaction scheme with a Langmuir-Hinshelwood representation, the model takes into account the influence of temperature, total pressure and hydrogen sulphide partial pressure on the reaction rates for hydro-desulfurization, hydro-denitrogenation and hydro-de-aromatization. The model parameter estimation was based on experiments that were carried out on a micro-pilot unit using an industrial sulfided NiMo/Al{sub 2}O{sub 3} catalyst and LCO feedstocks. The analytical study of the sulphur compounds was also extended to the case of straight run gas-oils (SR). For these feedstocks, a method using high-resolution mass spectrometry coupled with gas chromatography (GC-HRMS) was developed. In this way, the kinetic model can now be extended for the SR gas-oil hydro-treating or for LCO-SR mixtures. (author)

Parameter Estimation of Partial Differential Equation Models.

Science.gov (United States)

Xun, Xiaolei; Cao, Jiguo; Mallick, Bani; Carroll, Raymond J; Maity, Arnab

2013-01-01

Partial differential equation (PDE) models are commonly used to model complex dynamic systems in applied sciences such as biology and finance. The forms of these PDE models are usually proposed by experts based on their prior knowledge and understanding of the dynamic system. Parameters in PDE models often have interesting scientific interpretations, but their values are often unknown, and need to be estimated from the measurements of the dynamic system in the present of measurement errors. Most PDEs used in practice have no analytic solutions, and can only be solved with numerical methods. Currently, methods for estimating PDE parameters require repeatedly solving PDEs numerically under thousands of candidate parameter values, and thus the computational load is high. In this article, we propose two methods to estimate parameters in PDE models: a parameter cascading method and a Bayesian approach. In both methods, the underlying dynamic process modeled with the PDE model is represented via basis function expansion. For the parameter cascading method, we develop two nested levels of optimization to estimate the PDE parameters. For the Bayesian method, we develop a joint model for data and the PDE, and develop a novel hierarchical model allowing us to employ Markov chain Monte Carlo (MCMC) techniques to make posterior inference. Simulation studies show that the Bayesian method and parameter cascading method are comparable, and both outperform other available methods in terms of estimation accuracy. The two methods are demonstrated by estimating parameters in a PDE model from LIDAR data.

Comparison of optical-model and Lane-model analyses of sub-Coulomb protons on /sup 92,94/Zr

International Nuclear Information System (INIS)

Schrils, R.; Flynn, D.S.; Hershberger, R.L.; Gabbard, F.

1979-01-01

Accurate proton elastic-scattering cross sections were measured with enriched targets of /sup 92,94/Zr from E/sub p/ = 2.0 to 6.5 MeV. The elastic-scattering cross sections, together with absorption cross sections, were analyzed with a Lane model which employed the optical potential of Johnson et al. The resulting parameters were compared with those obtained with a single-channel optical model and negligible differences were found. Significant differences between the 92 Zr and 94 Zr real diffusenesses resulted from the inclusion of the (p,p) data in the analyses

Analysing, Interpreting, and Testing the Invariance of the Actor-Partner Interdependence Model

Directory of Open Access Journals (Sweden)

Gareau, Alexandre

2016-09-01

Full Text Available Although in recent years researchers have begun to utilize dyadic data analyses such as the actor-partner interdependence model (APIM, certain limitations to the applicability of these models still exist. Given the complexity of APIMs, most researchers will often use observed scores to estimate the model's parameters, which can significantly limit and underestimate statistical results. The aim of this article is to highlight the importance of conducting a confirmatory factor analysis (CFA of equivalent constructs between dyad members (i.e. measurement equivalence/invariance; ME/I. Different steps for merging CFA and APIM procedures will be detailed in order to shed light on new and integrative methods.

Intense deuterium nuclear fusion of pycnodeuterium-lumps coagulated locally within highly deuterated atom clusters

CERN Document Server

Yoshiaki, A; Zhang, Y C

2002-01-01

Embedded nano-Pd particles of 5 nm in size instantly abundant D-atoms more than 250% in the atomic ratio against Pd-atoms at room temperature when they are kept in D sub 2 gas pressurized to less than 10 atm. In such ultrahigh densities, 2-4 D-atoms can be coagulated inside each octahedral space of Pd lattice (pycnodeuterium-lump). When a stimulation energy such as latticequake causing by ultrasonic wave was supplied to those highly deuterated Pd particles, intense deuterium nuclear fusion (''solid fusion'') was generated there and both excess heat and sup 4 He gas were abundantly produced. Naturally, these facts can not be realized at all in bulk Pd. The results show that the nuclear fusion occurs without any hazardous rays in pycnodeuterium-lumps coagulated locally inside the each cell of the host metal lattice. These unit cells correspond to minimum unit of the solid fusion reactor as a ''Lattice Reactor''. (author)

Application of Biologically-Based Lumping To Investigate the Toxicological Interactions of a Complex Gasoline Mixture

Science.gov (United States)

People are often exposed to complex mixtures of environmental chemicals such as gasoline, tobacco smoke, water contaminants, or food additives. However, investigators have often considered complex mixtures as one lumped entity. Valuable information can be obtained from these exp...

Mass balance model parameter transferability on a tropical glacier

Science.gov (United States)

Gurgiser, Wolfgang; Mölg, Thomas; Nicholson, Lindsey; Kaser, Georg

2013-04-01

The mass balance and melt water production of glaciers is of particular interest in the Peruvian Andes where glacier melt water has markedly increased water supply during the pronounced dry seasons in recent decades. However, the melt water contribution from glaciers is projected to decrease with appreciable negative impacts on the local society within the coming decades. Understanding mass balance processes on tropical glaciers is a prerequisite for modeling present and future glacier runoff. As a first step towards this aim we applied a process-based surface mass balance model in order to calculate observed ablation at two stakes in the ablation zone of Shallap Glacier (4800 m a.s.l., 9°S) in the Cordillera Blanca, Peru. Under the tropical climate, the snow line migrates very frequently across most of the ablation zone all year round causing large temporal and spatial variations of glacier surface conditions and related ablation. Consequently, pronounced differences between the two chosen stakes and the two years were observed. Hourly records of temperature, humidity, wind speed, short wave incoming radiation, and precipitation are available from an automatic weather station (AWS) on the moraine near the glacier for the hydrological years 2006/07 and 2007/08 while stake readings are available at intervals of between 14 to 64 days. To optimize model parameters, we used 1000 model simulations in which the most sensitive model parameters were varied randomly within their physically meaningful ranges. The modeled surface height change was evaluated against the two stake locations in the lower ablation zone (SH11, 4760m) and in the upper ablation zone (SH22, 4816m), respectively. The optimal parameter set for each point achieved good model skill but if we transfer the best parameter combination from one stake site to the other stake site model errors increases significantly. The same happens if we optimize the model parameters for each year individually and transfer

Mathematical modeling of CANDU-PHWR

Energy Technology Data Exchange (ETDEWEB)

Gaber, F.A.; Aly, R.A.; El-Shal, A.O. [Atomic Energy Authority, Cairo (Egypt)

2003-07-01

The paper deals with the transient studies of CANDU 600 pressurized Heavy Water Reactor (PHWR). This study involved mathematical modeling of CANDU-PHWR to study its thermodynamic performances. Modeling of CANDU-PHWR was based on lumped parameter technique. The reactor model includes the neutronic, reactivity, and fuel channel heat transfer. The nuclear reactor power was modelled using the point kinetics equations with six groups of delayed neutrons and the reactivity feed back due to the changes in the fuel temperature and coolant temperature. The CANDU-PHWR model was coded in FORTRAN language and solved by using a standard numerical technique. The adequacy of the model was tested by assessing the physical plausibility of the obtained results. (author)

Linear and nonlinear analysis of density wave instability phenomena

International Nuclear Information System (INIS)

Ambrosini, Walter

1999-01-01

In this paper the mechanism of density-wave oscillations in a boiling channel with uniform and constant heat flux is analysed by linear and nonlinear analytical tools. A model developed on the basis of a semi-implicit numerical discretization of governing partial differential equations is used to provide information on the transient distribution of relevant variables along the channel during instabilities. Furthermore, a lumped parameter model and a distributed parameter model developed in previous activities are also adopted for independent confirmation of the observed trends. The obtained results are finally put in relation with the picture of the phenomenon proposed in classical descriptions. (author)

MODELLING BIOPHYSICAL PARAMETERS OF MAIZE USING LANDSAT 8 TIME SERIES

Directory of Open Access Journals (Sweden)

T. Dahms

2016-06-01

Full Text Available Open and free access to multi-frequent high-resolution data (e.g. Sentinel – 2 will fortify agricultural applications based on satellite data. The temporal and spatial resolution of these remote sensing datasets directly affects the applicability of remote sensing methods, for instance a robust retrieving of biophysical parameters over the entire growing season with very high geometric resolution. In this study we use machine learning methods to predict biophysical parameters, namely the fraction of absorbed photosynthetic radiation (FPAR, the leaf area index (LAI and the chlorophyll content, from high resolution remote sensing. 30 Landsat 8 OLI scenes were available in our study region in Mecklenburg-Western Pomerania, Germany. In-situ data were weekly to bi-weekly collected on 18 maize plots throughout the summer season 2015. The study aims at an optimized prediction of biophysical parameters and the identification of the best explaining spectral bands and vegetation indices. For this purpose, we used the entire in-situ dataset from 24.03.2015 to 15.10.2015. Random forest and conditional inference forests were used because of their explicit strong exploratory and predictive character. Variable importance measures allowed for analysing the relation between the biophysical parameters with respect to the spectral response, and the performance of the two approaches over the plant stock evolvement. Classical random forest regression outreached the performance of conditional inference forests, in particular when modelling the biophysical parameters over the entire growing period. For example, modelling biophysical parameters of maize for the entire vegetation period using random forests yielded: FPAR: R² = 0.85; RMSE = 0.11; LAI: R² = 0.64; RMSE = 0.9 and chlorophyll content (SPAD: R² = 0.80; RMSE=4.9. Our results demonstrate the great potential in using machine-learning methods for the interpretation of long-term multi-frequent remote sensing

Modelling Biophysical Parameters of Maize Using Landsat 8 Time Series

Science.gov (United States)

Dahms, Thorsten; Seissiger, Sylvia; Conrad, Christopher; Borg, Erik

2016-06-01

Open and free access to multi-frequent high-resolution data (e.g. Sentinel - 2) will fortify agricultural applications based on satellite data. The temporal and spatial resolution of these remote sensing datasets directly affects the applicability of remote sensing methods, for instance a robust retrieving of biophysical parameters over the entire growing season with very high geometric resolution. In this study we use machine learning methods to predict biophysical parameters, namely the fraction of absorbed photosynthetic radiation (FPAR), the leaf area index (LAI) and the chlorophyll content, from high resolution remote sensing. 30 Landsat 8 OLI scenes were available in our study region in Mecklenburg-Western Pomerania, Germany. In-situ data were weekly to bi-weekly collected on 18 maize plots throughout the summer season 2015. The study aims at an optimized prediction of biophysical parameters and the identification of the best explaining spectral bands and vegetation indices. For this purpose, we used the entire in-situ dataset from 24.03.2015 to 15.10.2015. Random forest and conditional inference forests were used because of their explicit strong exploratory and predictive character. Variable importance measures allowed for analysing the relation between the biophysical parameters with respect to the spectral response, and the performance of the two approaches over the plant stock evolvement. Classical random forest regression outreached the performance of conditional inference forests, in particular when modelling the biophysical parameters over the entire growing period. For example, modelling biophysical parameters of maize for the entire vegetation period using random forests yielded: FPAR: R² = 0.85; RMSE = 0.11; LAI: R² = 0.64; RMSE = 0.9 and chlorophyll content (SPAD): R² = 0.80; RMSE=4.9. Our results demonstrate the great potential in using machine-learning methods for the interpretation of long-term multi-frequent remote sensing datasets to model

Quality assessment for radiological model parameters

International Nuclear Information System (INIS)

Funtowicz, S.O.

1989-01-01

A prototype framework for representing uncertainties in radiological model parameters is introduced. This follows earlier development in this journal of a corresponding framework for representing uncertainties in radiological data. Refinements and extensions to the earlier framework are needed in order to take account of the additional contextual factors consequent on using data entries to quantify model parameters. The parameter coding can in turn feed in to methods for evaluating uncertainties in calculated model outputs. (author)

Structure-soil-structure interaction of nuclear structures