Nutrient Uptake by High-Yielding Cotton Crop in Brazil

Directory of Open Access Journals (Sweden)

José Luís Vilela Vieira

2018-02-01

Full Text Available ABSTRACT: Determining nutrient uptake and accumulation rates by cotton crops is important to define management strategies, especially for transgenic varieties, which are cultivated using high-technology approaches that require substantial investment to maximize yield. Currently in Brazil, the states of Bahia and Mato Grosso are responsible for 84.4 % of the total cotton growing area. In the present study, two trials were conducted in 2013, one that involved planting FM 940 GLT, FM 980 GLT, and FM 913 GLT varieties in the state of Bahia and the other which involved FM 940 GLT and FM 980 GLT varieties in the state of Mato Grosso. The aim of the two trials was to represent the two regions that currently encompass the largest areas of cotton cultivation. Tissue samples, consisting of leaves, stems, and reproductive components, were collected eleven times during the crop cycle for determination of nutrient content and shoot dry matter. After weighing, plant tissue samples were dried and ground to determine nutrient contents. Because there were no overall differences in nutrient contents and biomass accumulation of the varieties during the crop cycle, we undertook joint analysis of the data from all varieties at each site. Favorable climatic conditions in Bahia promoted plant biomass production that was twice as much as plants grown in Mato Grosso, with cotton yields of 6.2 and 3.8 t ha−1 of lint and seed, respectively. The maximum nutrient accumulation occurred between 137-150 days after emergence (DAE for N; 143-148 for P; 172-185 for K; 100 for Ca; 144-149 for Mg; and 153-158 for S. Maximum uptake ranged from 218-362 kg ha−1 N; 26-53 kg ha−1 P; 233-506 kg ha−1 K; 91-202 kg ha−1 Ca; 28-44 kg ha−1 Mg; and 19-61 kg ha−1 S. On average, the sites revealed nutrient export of 14, 2, 23, 3, 2, and 2 kg t−1 of lint and seed for N, P, K, Ca, Mg, and S, respectively, with little variation among sites. Extraction of nutrients per area by cotton

Probing bias reduction to improve comparability of lint cotton water and moisture contents at moisture equilibrium

Science.gov (United States)

The Karl Fischer Titration (KFT) reference method is specific for water in lint cotton and was designed for samples conditioned to moisture equilibrium, thus limiting its biases. There is a standard method for moisture content – weight loss – by oven drying (OD), just not for equilibrium moisture c...

Cottonseed protein, oil, and mineral status in near-isogenic Gossypium hirsutum cotton lines expressing fuzzy/linted and fuzzless/linted seed phenotypes under field conditions

Directory of Open Access Journals (Sweden)

Nacer eBellaloui

2015-03-01

Full Text Available Cotton is an important crop in the world and is a major source of oil for human consumption and cotton meal for livestock. Cottonseed nutrition (seed composition: protein, oil, and minerals determine the quality of seeds. Therefore, maintaining optimum levels of cottonseed nutrition is critical. Physiological and genetic mechanisms controlling the levels of these constituents in cottonseed are still largely unknown. Our previous research conducted under greenhouse conditions showed that seed and leaf nutrition differed between fuzzless and fuzzy seed isolines. Therefore, the objective of this research was to investigate the seed fuzz phenotype (trait effects on seed protein, oil, N, C, S, and minerals in five sets of near-isogenic mutant cotton lines for seed fuzz in a two-year experiment under field condition to evaluate the stability of the effect of the trait on seed nutrition. The isolines (genotypes in each set differ for the seed fuzz trait (fuzzless/linted seed line, N lines, and fuzzy/linted seed line, F lines. Results showed that seed protein was higher in the fuzzy genotype in all sets, but seed oil was higher in fuzzless genotype in all sets. The concentrations of seed Ca and C were higher in all fuzzless genotypes, but N, S, B, Fe, and Zn were higher in most of the fuzzy genotypes. Generally, minerals were higher in leaves of F lines, suggesting the translocation of minerals from leaves to seeds was limited. The research demonstrated that fiber development could be involved in cottonseed composition. This may be due to the involvement of fiber development in carbon and nitrogen metabolism, and the mobility of nutrients from leaves (source to seed (sink. This information is beneficial to breeders to consider fuzzless cottonseed for potential protein and oil use and select for higher oil or higher protein content, and to physiologists to further understand the mobility of minerals to increase the quality of cottonseed nutrition for

Heterosis and correlation in interspecific and intraspecific hybrids of cotton.

Science.gov (United States)

Munir, S; Hussain, S B; Manzoor, H; Quereshi, M K; Zubair, M; Nouman, W; Shehzad, A N; Rasul, S; Manzoor, S A

2016-06-24

Interspecific and intraspecific hybrids show varying degrees of heterosis for yield and yield components. Yield-component traits have complex genetic relationships with each other. To determine the relationship of yield-component traits and fiber traits with seed cotton yield, six lines (Bt. CIM-599, CIM-573, MNH-786, CIM-554, BH-167, and GIZA-7) and three test lines (MNH-886, V4, and CIM-557) were crossed in a line x tester mating design. Heterosis was observed for seed cotton yield, fiber traits, and for other yield-component traits. Heterosis in interspecific hybrids for seed cotton yield was more prominent than in intraspecific hybrids. The interspecific hybrid Giza-7 x MNH-886 had the highest heterosis (114.77), while among intraspecific hybrids, CIM-554 x CIM-557 had the highest heterosis (61.29) for seed cotton yield. A major trait contributing to seed cotton yield was bolls/plant followed by boll weight. Correlation studies revealed that bolls/plant, boll weight, lint weight/boll, lint index, seed index, lint/seed, staple length, and staple strength were significantly and positively associated with seed cotton yield. Selection based on boll weight, boll number, lint weight/boll, and lint index will be helpful for improving cotton seed yield.

Reference method for total water in lint cotton by automated oven drying combined with volumetric Karl Fischer titration

Science.gov (United States)

In a preliminary study to measure total water in lint cotton we demonstrated that volumetric Karl Fischer Titration of moisture transported by a carrier gas from an attached small oven is more accurate than standard oven drying in air. The objective of the present study was to assess the measuremen...

Comparison of cotton square and boll damage and resulting lint and seed loss caused by verde plant bug, Creontiades signatus

Science.gov (United States)

Retention of bolls and squares (referred to as fruit retention), boll damage, and resulting cotton lint and seed weight loss were assessed when two (2010) and three (2011) age classes of sympodial fruiting branches with different ages of squares and bolls where exposed to verde plant bug, Creontiade...

Genetic variation and heritability for cotton seed, fiber and oil traits in gossypium hirsutum

International Nuclear Information System (INIS)

Khan, N.U.; Farhatullah; Batool, S.; Makhdoom, K.; Marwat, K.B.; Hassan, G.; Ahmad, W.; Khan, H.U.

2010-01-01

The research work pertaining to the study of genetic variability, heritability, genetic gain and correlation for cottonseed, fiber and cottonseed oil % in Gossypium hirsutum cultivars was conducted during 2005 at NWFP Agricultural University Peshawar, Pakistan. Analysis of variance manifested highly significant differences among the genotypes for all the traits except seeds per locule. Genetic potential range of eight cotton cultivars for different parameters was recorded i.e. seeds locule-1 (6.33 to 6.60), seeds boll-1 (26.10 to 28.47), seed index (8.61 to 9.69 g), lint index (5.35 to 6.05 g), lint % (35.17 to 38.13 %), seed cotton yield (1200 to 2450 kg ha/sup -1/) and cottonseed oil % (27.52 to 30.15%). Genetic variances were found almost greater than the environmental variances for all the traits except seeds locule-1 and seed index. High broad sense heritability and selection response were also formulated for seeds boll-1 (0.67, 0.84), seed index (0.77, 0.47 g), lint index (0.96, 0.33 g), lint % (0.96, 1.66 %), seed cotton yield (0.98, 643.16 kg) and cottonseed oil % (0.87, 1.28 %), respectively. Correlation of yield with other traits was found positive for majority of traits except seeds locule-1 and cotton seed oil %. Seed cotton yield is our ultimate goal in growing cotton besides lint %. Highest seed cotton yield was recorded in CIM-499 followed by CIM-473, CIM-496 and CIM-506 and were also found as the second and third top scoring genotypes for seeds per boll, seed index, lint % and cottonseed oil %. Cultivar SLH-279 performed better for lint index, lint % and oil %. This type of correlation is rarely found and ultra desirable by the cotton breeders and a little genetic gain in seed and lint traits, and oil content is a great accomplishment. (author)

Analyse écophysiologique et modélisation de l’interaction génotype x environnement x itinéraire technique chez le cotonnier (Gossypium hirsutum L.) au Cameroun pour la conception d'idéotypes

OpenAIRE

Loison , Romain

2015-01-01

Cotton lint is the first natural fiber used in the world. Cotton provides income to more than 10 million persons in West and Central Africa. In Cameroon, it is produced under rainfed conditions and water shortage is the major abiotic factor limiting yield and lint quality. In this context, a breeding program was initiated in 1950 by IRCT (Institut de Recherches du Coton et des Textiles Exotiques) to increase lint yield, fiber quality and disease resistance. After 60 years, this program has re...

Response of Cotton to Irrigation Methods and Nitrogen Fertilization: Yield Components, Water-Use Efficiency, Nitrogen Uptake, and Recovery

International Nuclear Information System (INIS)

Janat, M.

2009-01-01

Efficient crop use of nitrogen (N) fertilizer is critical from economic and environmental viewpoints, especially under irrigated conditions. Cotton yield parameters, fiber quality, water- and N-use efficiency responses to N, and irrigation methods in northern Syria were evaluated. Field trials were conducted for two growing seasons on a Chromoxerertic Rhodoxeralf soil. Treatments consisted of drip fertigation, furrow irrigation, and five different rates of N fertilizer (50, 100, 150, 200, and 250 kg N /ha). Cotton was irrigated when soil moisture in the specified active root depth was 80% of the field capacity as indicated by the neutron probe. Seed cotton yield was higher than the national average (3,928 kg/ha) by at least 12% as compared to all treatments. Lint properties were not negatively affected by the irrigation method or N rates. Water savings under drip fertigation ranged between 25 and 50% of irrigation water relative to furrow irrigation. Crop water-use efficiencies of the drip-fertigated treatments were in most cases 100% higher than those of the corresponding furrow-irrigated treatments. The highest water demand was during the fruit-setting growth stage. It was also concluded that under drip fertigation, 100 -150 N kg/ha was adequate and comparable with the highest N rates tested under furrow irrigation regarding lint yield, N uptake, and recovery. Based on cotton seed yield and weight of stems, the overall amount of N removed from the field for the drip-fertigated treatments ranged between 101-118 kg and 116-188 N/ha for 2001 and 2002, respectively. The N removal ranged between 94-113 and 111-144 kg N/ha for the furrow-irrigated treatments for 2001 and 2002, respectively. (author)

Inheritance of the ovule fuzzless trait for Gossypium arboreum germplasm line PI 529708

Science.gov (United States)

Background: Cotton is the most important fiber crop and understanding the genetic mechanisms controlling fiber production on cotton seeds can aid in the development of improved varieties with higher lint yields and improved fiber quality. Lint and fuzz are the two types of fiber produced on the cott...

Impact of plastic mulching on nitrous oxide emissions in China's arid agricultural region under climate change conditions

Science.gov (United States)

Yu, Yongxiang; Tao, Hui; Jia, Hongtao; Zhao, Chengyi

2017-06-01

The denitrification-decomposition (DNDC) model is a useful tool for integrating the effects of agricultural practices and climate change on soil nitrous oxide (N2O) emissions from agricultural ecosystems. In this study, the DNDC model was evaluated against observations and used to simulate the effect of plastic mulching on soil N2O emissions and crop growth. The DNDC model performed well in simulating temporal variations in N2O emissions and plant growth during the observation period, although it slightly underestimated the cumulative N2O emissions, and was able to simulate the effects of plastic mulching on N2O emissions and crop yield. Both the observations and simulations demonstrated that the application of plastic film increased cumulative N2O emissions and cotton lint yield compared with the non-mulched treatment. The sensitivity test showed that the N2O emissions and lint yield were sensitive to changes in climate and management practices, and the application of plastic film made the N2O emissions and lint yield less sensitive to changes in temperature and irrigation. Although the simulations showed that the beneficial impacts of plastic mulching on N2O emissions were not gained under high fertilizer and irrigation scenarios, our simulations suggest that the application of plastic film effectively reduced soil N2O emissions while promoting yields under suitable fertilizer rates and irrigation. Compared with the baseline scenario, future climate change significantly increased N2O emissions by 15-17% without significantly influencing the lint yields in the non-mulched treatment; in the mulched treatment, climate change significantly promoted the lint yield by 5-6% and significantly reduced N2O emissions by 14% in the RCP4.5 and RCP8.5 scenarios. Overall, our results demonstrate that the application of plastic film is an efficient way to address increased N2O emissions and simultaneously enhance crop yield in the future.

Biochar derived from corn straw affected availability and distribution of soil nutrients and cotton yield.

Directory of Open Access Journals (Sweden)

Xiaofei Tian

Full Text Available Biochar application as a soil amendment has been proposed as a strategy to improve soil fertility and increase crop yields. However, the effects of successive biochar applications on cotton yields and nutrient distribution in soil are not well documented. A three-year field study was conducted to investigate the effects of successive biochar applications at different rates on cotton yield and on the soil nutrient distribution in the 0-100 cm soil profile. Biochar was applied at 0, 5, 10, and 20 t ha-1 (expressed as Control, BC5, BC10, and BC20, respectively for each cotton season, with identical doses of chemical fertilizers. Biochar enhanced the cotton lint yield by 8.0-15.8%, 9.3-13.9%, and 9.2-21.9% in 2013, 2014, and 2015, respectively, and high levels of biochar application achieved high cotton yields each year. Leaching of soil nitrate was reduced, while the pH values, soil organic carbon, total nitrogen (N, and available K content of the 0-20 cm soil layer were increased in 2014 and 2015. However, the changes in the soil available P content were less substantial. This study suggests that successive biochar amendments have the potential to enhance cotton productivity and soil fertility while reducing nitrate leaching.

Biochar derived from corn straw affected availability and distribution of soil nutrients and cotton yield.

Science.gov (United States)

Tian, Xiaofei; Li, Chengliang; Zhang, Min; Wan, Yongshan; Xie, Zhihua; Chen, Baocheng; Li, Wenqing

2018-01-01

Biochar application as a soil amendment has been proposed as a strategy to improve soil fertility and increase crop yields. However, the effects of successive biochar applications on cotton yields and nutrient distribution in soil are not well documented. A three-year field study was conducted to investigate the effects of successive biochar applications at different rates on cotton yield and on the soil nutrient distribution in the 0-100 cm soil profile. Biochar was applied at 0, 5, 10, and 20 t ha-1 (expressed as Control, BC5, BC10, and BC20, respectively) for each cotton season, with identical doses of chemical fertilizers. Biochar enhanced the cotton lint yield by 8.0-15.8%, 9.3-13.9%, and 9.2-21.9% in 2013, 2014, and 2015, respectively, and high levels of biochar application achieved high cotton yields each year. Leaching of soil nitrate was reduced, while the pH values, soil organic carbon, total nitrogen (N), and available K content of the 0-20 cm soil layer were increased in 2014 and 2015. However, the changes in the soil available P content were less substantial. This study suggests that successive biochar amendments have the potential to enhance cotton productivity and soil fertility while reducing nitrate leaching.

Application of DSSAT-CROPGRO-Cotton Model to Assess Long Term (1924-2012) Cotton Yield under Different Irrigation Management Strategies

Science.gov (United States)

Adhikari, P.; Gowda, P. H.; Northup, B. K.; Rocateli, A.

2017-12-01

In this study a well calibrated and validated DSSAT-CROPGRO-Cotton model was used for assessing the irrigation management in the Texas High Plains (THP). Long term (1924-2012) historic lint yield were simulated under different irrigation management practices which were commonly used in the THP. The simulation treatments includes different amount of irrigation water high (H; 6.4 mm d-1), medium (M; 3.2 mm d-1) and low (L; 0 mm d-1) during emergence (S1), vegetative (S2) and maturity (S3) stage. The combination of these treatments resulted into 27 treatments. The amount and date of irrigation for each stage were obtained from the recent cotton irrigation experiment at Halfway, TX (Brodovsky, et al., 2015). Similarly, calibrated model was also used to observe the effect of plantation date on crop yield in the THP regions.

Biochar derived from corn straw affected availability and distribution of soil nutrients and cotton yield

Science.gov (United States)

Tian, Xiaofei; Zhang, Min; Wan, Yongshan; Xie, Zhihua; Chen, Baocheng; Li, Wenqing

2018-01-01

Biochar application as a soil amendment has been proposed as a strategy to improve soil fertility and increase crop yields. However, the effects of successive biochar applications on cotton yields and nutrient distribution in soil are not well documented. A three-year field study was conducted to investigate the effects of successive biochar applications at different rates on cotton yield and on the soil nutrient distribution in the 0–100 cm soil profile. Biochar was applied at 0, 5, 10, and 20 t ha-1 (expressed as Control, BC5, BC10, and BC20, respectively) for each cotton season, with identical doses of chemical fertilizers. Biochar enhanced the cotton lint yield by 8.0–15.8%, 9.3–13.9%, and 9.2–21.9% in 2013, 2014, and 2015, respectively, and high levels of biochar application achieved high cotton yields each year. Leaching of soil nitrate was reduced, while the pH values, soil organic carbon, total nitrogen (N), and available K content of the 0–20 cm soil layer were increased in 2014 and 2015. However, the changes in the soil available P content were less substantial. This study suggests that successive biochar amendments have the potential to enhance cotton productivity and soil fertility while reducing nitrate leaching. PMID:29324750

EFEITO DA IRRIGAÇÃO NO RENDIMENTO E QUALIDADE DE FIBRAS EM CULTIVARES DE ALGODOEIRO HERBÁCEO

Directory of Open Access Journals (Sweden)

JOÃO HENRIQUE ZONTA

2015-01-01

Full Text Available This study was conducted to evaluate seed cotton yield, fiber yield, and fiber quality traits of cotton cultivars grown under different irrigation levels in Brazil. The experiment was conducted over two years in the region of Apodi – RN, with sprinkler irrigation. Treatments comprised of 4 irrigation levels i.e., 130, 100, 70 and 40 % of the crop evapotranspiration (ETc and 4 cotton cultivars i.e., FiberMax 993, BRS 286, BRS 336 and BRS 335. The experimental design was factorial with randomized complete block design and four replicates. Yield, lint percent and fiber quality traits determined were evaluated. Different responses were observed for cultivars at various irrigation levels. Cultivars grown under limited irrigation exhibited a decline in the seed cotton yield, lint percent, and fiber quality. Cultivars with the highest yield and lint percent were FiberMax 993 and BRS 286. Within irrigation level of 40 % ETc, the medium fiber cultivars produced short fibers whereas the long fiber cultivar, BRS 336, produced medium fiber length. Overall, the different levels of water deficits did not significantly affect fiber quality of the four cultivars tested as all fiber quality traits re- mained acceptable for the domestic textile industry.

Relationship Between Piercing-Sucking Insect Control and Internal Lint and Seed Rot in Southeastern Cotton (Gossypium hirsutum L.).

Science.gov (United States)

Medrano, Enrique G; Bell, Alois A; Greene, Jeremy K; Roberts, Phillip M; Bacheler, Jack S; Marois, James J; Wright, David L; Esquivel, Jesus F; Nichols, Robert L; Duke, Sara

2015-08-01

In 1999, crop consultants scouting for stink bugs (Hemiptera spp.) in South Carolina discovered a formerly unobserved seed rot of cotton that caused yield losses ranging from 10 to 15% in certain fields. The disease has subsequently been reported in fields throughout the southeastern Cotton Belt. Externally, diseased bolls appeared undamaged; internally, green fruit contain pink to dark brown, damp, deformed lint, and necrotic seeds. In greenhouse experiments, we demonstrated transmission of the opportunistic bacterium Pantoea agglomerans by the southern green stink bug, Nezara viridula (L.). Here, green bolls were sampled from stink bug management plots (insecticide protected or nontreated) from four South Atlantic coast states (North Carolina, South Carolina, Georgia, and Florida) to determine disease incidence in the field and its association with piercing-sucking insects feeding. A logistic regression analysis of the boll damage data revealed that disease was 24 times more likely to occur (P = 0.004) in bolls collected from plots in Florida, where evidence of pest pressure was highest, than in bolls harvested in NC with the lowest detected insect pressure. Fruit from plots treated with insecticide, a treatment which reduced transmission agent numbers, were 4 times less likely to be diseased than bolls from unprotected sites (P = 0.002). Overall, punctured bolls were 125 times more likely to also have disease symptoms than nonpunctured bolls, irrespective of whether or not plots were protected with insecticides (P = 0.0001). Much of the damage to cotton bolls that is commonly attributed to stink bug feeding is likely the resulting effect of vectored pathogens. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

L(3)mbt and the LINT complex safeguard cellular identity in the Drosophila ovary.

Science.gov (United States)

Coux, Rémi-Xavier; Teixeira, Felipe Karam; Lehmann, Ruth

2018-04-04

Maintenance of cellular identity is essential for tissue development and homeostasis. At the molecular level, cell identity is determined by the coordinated activation and repression of defined sets of genes. The tumor suppressor L(3)mbt has been shown to secure cellular identity in Drosophila larval brains by repressing germline-specific genes. Here, we interrogate the temporal and spatial requirements for L(3)mbt in the Drosophila ovary, and show that it safeguards the integrity of both somatic and germline tissues. l(3)mbt mutant ovaries exhibit multiple developmental defects, which we find to be largely caused by the inappropriate expression of a single gene, nanos , a key regulator of germline fate, in the somatic ovarian cells. In the female germline, we find that L(3)mbt represses testis-specific and neuronal genes. At the molecular level, we show that L(3)mbt function in the ovary is mediated through its co-factor Lint-1 but independently of the dREAM complex. Together, our work uncovers a more complex role for L(3)mbt than previously understood and demonstrates that L(3)mbt secures tissue identity by preventing the simultaneous expression of original identity markers and tissue-specific misexpression signatures. © 2018. Published by The Company of Biologists Ltd.

Productivity and resource use in cotton and wheat relay intercropping

NARCIS (Netherlands)

Zhang, L.

2007-01-01

Keywords: Grain yield; lint yield; phenological delay; light use; nitrogen use; resource use efficiency; modelling; profitability; water productivity. From the early 1980s onwards, farmers in the Yellow River cotton producing region intercropped cotton and winter wheat; currently on more than 60% of

on the genetic relationships among t

African Journals Online (AJOL)

STORAGESEVER

2009-10-05

Oct 5, 2009 ... Establishment and prebloom irrigations affect total yield, but water ... For most major food ... avoidance is performed by maintenance of turgor through .... Productivity of cotton populations selected for lint yield under dry land and irrigated ... according to the manufacturer's supplied protocol, starting with 225.

African Journal of Biotechnology - Vol 10, No 44 (2011)

African Journals Online (AJOL)

The effect of zinc application methods on seed cotton yield, lint and seed quality of ... Management of Meloidogyne incognita in nematodesusceptible watermelon ... Waste cooking oil transesterification: Influence of impeller type, temperature, ...

Thermal neutron calibration of a tritium extraction facility using the 6Li(n,t)4He/197Au(n,γ)198Au cross section ratio for standardization

International Nuclear Information System (INIS)

Bretscher, M.M.; Smith, D.L.

1980-08-01

Absolute tritium activities in a neutron-activated metallic lithium samples have been measured by liquid scintillation methods to provide data needed for the determination of capture-to-fission ratios in fast breeder reactor spectra and for recent measurements of the 7 Li(n,n't) 4 He cross section. The tritium extraction facility used for all these experiments has now been calibrated by measuring the 6 Li(n,t) 4 He/ 197 Au/n,γ) 198 Au activity ratio for thermal neutrons and comparing the result with the well-known cross sections. The calculated-to-measured activity ratio was found to be 1.033 +- 0.018. 2 figures, 20 tables

Internationalisierung des Lehramts – eine Quadratur des Kreises? Zu Chancen und Grenzen eines grenzüberschreitenden Paradigmas der Lehrerbildung am Beispiel des Masterstudiengangs MEEF / LINT (Lehramt International Nizza-Regensburg

Directory of Open Access Journals (Sweden)

Jochen Mecke

2016-03-01

Full Text Available Die Internationalisierung ist nicht das Problem, sie ist die Lösung: In einer europäischen Gesellschaft, in der die Dynamik einer neuen Vielfalt derzeit eine der wenigen Konstanten darstellt, die nationenübergreifend Bestand hat und keine Grenzen kennt, brauchen wir eine Lehrerbildung, die strukturell und konzeptionell so gesamteuropäisch angelegt ist wie ihre Herausforderungen. Wir brauchen trotz und wegen verschiedener bildungspolitischer Unterschiede und Hürden neue Ansätze der Kooperation und Vernetzung, deren Chancen und Herausforderungen in der Folge exemplarisch am binationalen Master of Education MEEF / LINT (Lehramt International Deutsch-Französisch skizziert werden sollen.

Genotype-by-sowing date interaction effects on cotton yield and quality in irrigated condition of dera ismail khan, pakistan

International Nuclear Information System (INIS)

Usman, K.; Khan, S.; Ayatullah, A.

2016-01-01

Cotton is a major export commodity of Pakistan. It is affected by variable environmental conditions throughout the country which limits its production. A 2-year field study was conducted in 2012 and 2013 at Cotton Research Station, Dera Ismail Khan, Pakistan to evaluate the effects of six sowing dates on yield and quality attributes of four cotton genotypes. The experiments were laid out in split-plot within a randomized complete block design with three replications. Main plots treatments were six sowing dates, namely March 20, April 4, April 19, May 4, May 19, and June 3 while subplots treatments were four approved transgenic varieties of cotton (CIM-598, CIM-599, CIM-602, and Ali Akber-703). Results revealed that earlier planting produced more vegetative growth rather than lint yield while late planting induced flowering and boll formation when temperature was much cold that adversely affected cotton yield and quality. The results further indicate that the genotype CIM-599 scored first rank in number of bolls plant-1, boll weight, seed cotton yield, ginning out turn, fiber length, fiber strength, fiber fineness, and fiber uniformity when sown on April 19. CIM-598 was the next suitable genotype after CIM-599 which produced higher yield and quality traits in April 19 sowing. Earlier and later sowing than April 19 resulted in lower cotton yield and quality characters due to unfavorable environmental conditions and shorter growth period, respectively. Thus it is concluded that the genotype, CIM-599 sown on April 19 suits well to the study area and had the potential to optimize cotton yield and quality in irrigated condition of Dera Ismail Khan, Pakistan. (author)

Cotton Water Use Efficiency under Two Different Deficit Irrigation Scheduling Methods

Directory of Open Access Journals (Sweden)

Jeffrey T. Baker

2015-08-01

Full Text Available Declines in Ogallala aquifer levels used for irrigation has prompted research to identify methods for optimizing water use efficiency (WUE of cotton (Gossypium hirsutum L. In this experiment, conducted at Lubbock, TX, USA in 2014, our objective was to test two canopy temperature based stress indices, each at two different irrigation trigger set points: the Stress Time (ST method with irrigation triggers set at 5.5 (ST_5.5 and 8.5 h (ST_8.5 and the Crop Water Stress Index (CWSI method with irrigation triggers set at 0.3 (CWSI_0.3 and 0.6 (CWSI_0.6. When these irrigation triggers were exceeded on a given day, the crop was deficit irrigated with 5 mm of water via subsurface drip tape. Also included in the experimental design were a well-watered (WW control irrigated at 110% of potential evapotranspiration and a dry land (DL treatment that relied on rainfall only. Seasonal crop water use ranged from 353 to 625 mm across these six treatments. As expected, cotton lint yield increased with increasing crop water use but lint yield WUE displayed asignificant (p ≤ 0.05 peak near 3.6 to 3.7 kg ha−1 mm−1 for the ST_5.5 and CWSI_0.3 treatments, respectively. Our results suggest that WUE may be optimized in cotton with less water than that needed for maximum lint yield.

Cotton harvest at 40% versus 75% boll-splitting on yield and economic return under standard and proactive boll weevil (Coleoptera: Curculionidae) spray regimes.

Science.gov (United States)

Showler, A T; Robinson, J R C

2008-10-01

The standard practice of two or three preemptive insecticide applications at the start of pinhead (1-2-mm-diameter) squaring followed by threshold-triggered (when 10% of randomly selected squares have oviposition punctures) insecticide applications for boll weevil, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), control does not provide reliable protection of cotton, Gossypium hirsutum L., lint production. This study, conducted during 2004 and 2005, showed that three to six fewer spray applications in a "proactive" approach, in which spraying began at the start of large (5.5-8-mm-diameter) square formation and continued at approximately 7-d intervals while large squares were abundant, resulted in fewer infested squares and 1.4- to 1.7-fold more lint than the standard treatment. Fewer sprays and increased yield made proactive spraying significantly more profitable than the standard approach, which resulted in relatively low or negative economic returns. Harvest at 75% boll-split in the proactive spray regime of 2005 resulted in four-fold greater economic return than cotton harvested at 40% boll-split because of improved protection of large squares and the elimination of late-season sprays inherent to standard spray regime despite the cost of an extra irrigation in the 75% boll-split treatments. The earlier, 40% harvest trigger does not avoid high late-season boll weevil pressure, which exerts less impact on bolls, the predominant form of fruiting body at that time, than on squares. Proactive spraying and harvest timing are based on an important relationship between nutrition, boll weevil reproduction, and economic inputs; therefore, the tactic of combining proaction with harvest at 75% boll-split is applicable where boll weevils are problematic regardless of climate or region, or whether an eradication program is ongoing.

Transcriptional Profiling in Cotton Associated with Bacillus Subtilis (UFLA285) Induced Biotic-Stress Tolerance

Science.gov (United States)

Abstract Lint yield and quality in cotton is greatly affected by water-deficit stress. The principal aim of this study was to identify cotton genes associated metabolic pathways involved in the water-deficit stress response. Gene expression profiles were developed for leaf and root tissues subject...

Creation and evaluation of best cotton mutant lines

International Nuclear Information System (INIS)

Rastegari, S. J.; Hosseini, Z.

2001-01-01

During (1997-1999) a study was carried out to recognize the best mutant lines, which were already obtained from a mutation breeding project. A Triple Rectangular Latis Design (8 7) in form of randomized complete blocks (RCB) with fifty- six treatments and three replications, were used in Estahban, Kordkouy and Varamin, under different ecological conditions, rainfall (Kordkouy) desert (Varamin) hot and dry (Estahban). During growing season some important morphological characteristics were recorded. Some lines had specific characters, for example: line 3191 (Chirpan 150 gray) had a low leaf number per plant, line 3169 (Bakhtegan 200 gray) plants were clustered. The results of the data in Varamin station showed that Bakhtegan irradiated with 150 gray line 3485 and Tashkand with 300 gray line 3451 compared to check (Varamin with 4373 kg/ha) had highest yield with 4942 kg/ha, and 4871 kg/ha respectively. In view of boll weight line 3405 of Sahel irradiated with 200 gray had highest boll weight (6.5 g/boll). In Kordkouy station the best mutant line was Chirpan irradiated with 250 gray, line 3208, with 20% yield increase compared to Sahel and 30% yield increase compared to original Chirpan. In respect to irradiation effect on lint percentage and fiber quality, the results showed; there was a positive effect on lint percentage of all varieties, especially in Tashkant, Bakhtegan and Chirpan which are inherently weak in lint percentage. As a whole gamma radiation did not have any negative effect on fiber quality. Even in Estahban 1.6 to 2.4 mm fiber increase were observed in some Chirpan irradiated material (C150-3516) and (C200-3523)

Measurements of differential cross sections for the reactions 6,7Li(n,d)5,6He and 6,7Li(n,t)4,5He at 14.1 MeV

International Nuclear Information System (INIS)

Shirato, Shoji; Hata, Kazuhiro; Ando, Yoshiaki; Shibuya, Shinji; Shibata, Keiichi.

1989-08-01

A summary of our measured cross sections for the 14.1 MeV neutron-induced reactions on lithium isotopes has been presented. Our data were measured with two counter telescopes, each of which consisted of two gas proportional counters and silicon ΔE and E detectors. Measured energy spectra of deuterons and tritons from 6 Li(n,d)n 4 He and 7 Li(n,t)n 4 He, respectively, were analyzed by a simple final-state interaction theory. Measured angular distributions for these reactions as well as 6 Li(n,t) 4 He and 7 Li(n,d) 6 He were analyzed by exact finite-range distorted wave Born approximation (EFR-DWBA) calculations. Spectroscopic factors extracted from the EFR-DWBA analyses have been compared with theoretical predictions. (author)

Correlations and Correlated Responses in Upland Cotton (Gossypium hirsutum L.

Directory of Open Access Journals (Sweden)

Echekwu, CA.

2001-01-01

Full Text Available Plant breeders must be concerned with the total array of economic characters in their efforts to develop a crop variety acceptable to farmers. Their selection endeavours must therefore take into consideration how changes in one trait affect, simultaneously changes in other economic attributes. The importance of correlations and correlated responses is therefore self evident in plant breeding endeavours. In this study F3 progenies from a cross between two cotton lines SAMCOT-9 x Y422 were evaluated for two years and performance data were used to obtain correlations between nine agronomic and fibre quality traits in upland cotton. The results indicated that plant helght was significantly and positively correlated with seed cotton yield, number of sympodial and monopodial branches, seed index, fibre length and micronaire index. Positive and significant correlations were also obtained between : seed cotton yield, tint percent and fibre strength and fibre length. Significant negative correlations were obtained between : plant height and lint percent ; number of monopodial branches, sympodial branches and lint percent ; fibre length, fibre strength and micronaire index. The correlated responses in the other eight traits when selection was practiced for seed cotton yield in the present study shows that it might be more profitable to practice direct selection for seed cotton yield compared to selecting for seed cotton yield through any of the other traits.

Performance of cotton crop grown under surface irrigation and drip fertigation. I. seed cotton yield, dry matter production, and lint properties

International Nuclear Information System (INIS)

Janat, M.; Somi, G.

2002-01-01

Drip fertigation is a key factor in modern irrigated agriculture, where water and fertilizers are the most expensive inputs for this irrigation method. Drip fertigation experiments were carried out a Hama, north of Syria (Tezeen's Irrigation Research Station), for four consecutive years 1995 - 1998. Cotton (Gossypium hirsutim L.) variety Aleppo 33/1 was planted after unfertilized maize in order to deplete as much as possible the available N and reduce the field variability on the corresponding experimental units and irrigated thereafter. Treatments consisted of two irrigation methods (Surface irrigation and drip fertigation) and five N rates within drip fertigated cotton, including the control (N 0 = 0, N 1 = 60, N 2 = 120, N 3 = 180, N 4 240 kg N ha -1 ). The N fertilizer treatment for surface irrigated cotton was 180 kg N ha -1 in accordance with the recommended rate of ministry of Agriculture and Agrarian Reform. The experimental design was randomized block design with six replicates. Fertigation resulted in large water saving, and highly improved field water-use efficiency. Further, increasing N application rates under drip fertigation increased dry matter yield. The principal benefit of drip fertigation was the achievement of higher field water-use efficiencies, which were increased more than three-fold for both dry matter and seed cotton yield, relative to surface irrigation. The highest water-use efficiencies were obtained with the addition of 180 and 240 kg N ha -1 in 1995 and 1996 and 120 kg N ha -1 in 1997 and 1998. Dry matter production and partitioning among different plant parts at physiological maturity stage varied due to N input and irrigation methods. The overall dry matter distribution among different plant structures for drip fertigated-treatments was: Stems, 20.3 - 21.3%; leaves 26.3 - 28.7%; and fruiting forms, 50 - 53.2%. For the surface-irrigated treatment, the partitioning was stems, 23.1%; leaves, 28.3%; and fruiting form, 48.6%. The

Effect of cotton leaf-curl virus on the yield-components and fibre properties of cotton genotypes under varying plant spacing and nitrogen fertilizer

International Nuclear Information System (INIS)

Ahmad, S.; Hayat, K.; Ashraf, F.; Sadiq, M.A.

2008-01-01

Cotton leaf-curl virus (CLCu VB. Wala strain) is one of the major biotic constraints of cotton production in Punjab. Development of resistant cotton genotype is the most feasible, economical and effective method to combat this hazardous problem, but so far no resistant genotype has been reported. Therefore, the objective of this study was to compare yield and yield-components and fiber traits of different genotypes/varieties under different plant spacing and nitrogen fertilizer as a management strategy to cope with this viral disease. Field experiment was conducted during 2006-07 to evaluate the effect of genotype, plant spacing and nitrogen fertilizer on cotton. Five genotypes (MNH-786, MNH-789, MNH- 6070, CIM- 496, and BH-160), three plant-spacings (15, 30 and 45 cm) and three nitrogen fertilizer-levels (6.5, 8.6 and 11 bags Urea / ha) were studied. Results showed that significant differences exist for plant height, no. of bolls/m/sup -2/, seed-cotton yield (kg/ha) due to genotype, interaction of genotype with plant spacing and nitrogen fertilizer level. Whereas boll weight, ginning out-turn, staple length and fiber fineness were not affected significantly by the plant spacing and nitrogen fertilizer, the effect due to genotype was significant for these traits. CLCuV infestation varied significantly with genotypes, while all other factors, i.e., plant spacing and nitrogen fertilizers, have non-significant effect. As the major objective of cotton cultivation is production of lint for the country and seed- cotton yield for the farmers, it is noted that genotypes grown in narrow plant-spacing (15 cm) and higher nitrogen fertilizer level (11.0 bags of urea/ha) produced maximum seed-cotton yield under higher CLCu V infestation in case of CIM-496, MNH-789 and BH-I60, while the new strain MNH-6070 gave maximum yield under 30cm plant-spacing and 8.6 bags of urea/ha has the 2.3% CLCu V infestation was observed in this variety. From the present study, it is concluded that

ADAPTABILIDADE E ESTABILIDADE FENOTÍPICA DE CULTIVARES DE ALGODOEIRO NO ESTADO DO MATO GROSSO, BRASIL PHENOTYPIC ADAPTABILITY AND STABILITY OF COTTON CULTIVARS IN THE MATO GROSSO STATE, BRAZIL

Directory of Open Access Journals (Sweden)

Cristina Schetino Bastos

2007-09-01

Full Text Available

O objetivo deste trabalho foi o de avaliar a adaptabilidade e a estabilidade de cultivares de algodão (Gossypium hirsutum L., utilizando a metodologia proposta por Eberhart & Russell (1966. Para tanto, onze variedades de algodão foram avaliadas em sete locais do Estado do Mato Grosso, Brasil, em dois anos agrícolas (2002/2003 e 2003/2004. O delineamento experimental empregado foi o de blocos casualizados com quatro repetições e as características avaliadas foram a produtividade de algodão em caroço e a porcentagem de fibra. Com relação à produção de algodão em caroço, as cultivares BRS Aroeira, BRS Ipê, BRS Cedro, BRS Jatobá e Delta Opal demonstraram ampla adaptabilidade e estabilidade para as regiões produtoras do Estado. Entretanto, considerando a porcentagem de fibra, não foram encontradas cultivares de algodão com ampla adaptabilidade e estabilidade nos ambientes estudados.

PALAVRAS-CHAVE: Gossypium hirsutum; fibra; estabilidade.

The objective of this work was to evaluate the stability and adaptability of cotton (Gossypium hirsutum L. cultivars using the method of Eberhart & Russell (1966. Eleven varieties of cotton were tested at seven locations in Mato Grosso State, Brazil, in two growing seasons (2002/2003 and 2003/2004. The experimental design was the randomized complete blocks with four replications and the evaluated traits were lint percentage and seed cotton yield. For seed cotton yield, BRS Aroeira, BRS Ipê, BRS Cedro, BRS Jatobá and Delta Opal showed broad adaptability and stability in Mato Grosso State. However, for lint percentage there were not found cotton cultivars with both broad adaptability and stability for the studied environments.

Soil organic carbon loss and selective transportation under field simulated rainfall events.

Science.gov (United States)

Nie, Xiaodong; Li, Zhongwu; Huang, Jinquan; Huang, Bin; Zhang, Yan; Ma, Wenming; Hu, Yanbiao; Zeng, Guangming

2014-01-01

The study on the lateral movement of soil organic carbon (SOC) during soil erosion can improve the understanding of global carbon budget. Simulated rainfall experiments on small field plots were conducted to investigate the SOC lateral movement under different rainfall intensities and tillage practices. Two rainfall intensities (High intensity (HI) and Low intensity (LI)) and two tillage practices (No tillage (NT) and Conventional tillage (CT)) were maintained on three plots (2 m width × 5 m length): HI-NT, LI-NT and LI-CT. The rainfall lasted 60 minutes after the runoff generated, the sediment yield and runoff volume were measured and sampled at 6-min intervals. SOC concentration of sediment and runoff as well as the sediment particle size distribution were measured. The results showed that most of the eroded organic carbon (OC) was lost in form of sediment-bound organic carbon in all events. The amount of lost SOC in LI-NT event was 12.76 times greater than that in LI-CT event, whereas this measure in HI-NT event was 3.25 times greater than that in LI-NT event. These results suggest that conventional tillage as well as lower rainfall intensity can reduce the amount of lost SOC during short-term soil erosion. Meanwhile, the eroded sediment in all events was enriched in OC, and higher enrichment ratio of OC (ERoc) in sediment was observed in LI events than that in HI event, whereas similar ERoc curves were found in LI-CT and LI-NT events. Furthermore, significant correlations between ERoc and different size sediment particles were only observed in HI-NT event. This indicates that the enrichment of OC is dependent on the erosion process, and the specific enrichment mechanisms with respect to different erosion processes should be studied in future.

VAT-teater vaatab 30 aastat tulevikku / Tiiu Laks

Index Scriptorium Estoniae

Laks, Tiiu, 1984-

2010-01-01

VAT Teater toob S. Becketti "Krappi viimase lindi" lavale ebatavalisel moel. Festivalil "Draama 2010" Tartus toimub 8. septembril esimene avalik lindistus "...viimane lint / Saare esimene lint". Kontseptsioon: Tanel Saar ja Co. Esitus: Tanel Saar ja Hanna Allsaar. Näitejuhid-konsultandid: Rait Avestik ja Aare Toikka. "Krappi viimane lint" esietendub VAT Teatri ja Tanel Saare esituses 2040. a. sügisel. Festivali "Draama 2010" kavast

The nature of navel fluff.

Science.gov (United States)

Steinhauser, Georg

2009-06-01

Hard facts on a soft matter! In their popular scientific book (Leyner M, Goldberg B. Why do men have nipples - hundreds of questions you'd only ask a doctor after your third martini. New York: Three Rivers Press; 2005), Leyner and Goldberg raised the question why "some belly buttons collect so much lint". They were, however, not able to come up with a satisfactory answer. The hypothesis presented herein says that abdominal hair is mainly responsible for the accumulation of navel lint, which, therefore, this is a typically male phenomenon. The abdominal hair collects fibers from cotton shirts and directs them into the navel where they are compacted to a felt-like matter. The most abundant individual mass of a piece of lint was found to be between 1.20 and 1.29 mg (n=503). However, due to several much larger pieces, the average mass was 1.82 mg in this three year study. When the abdominal hair is shaved, no more lint is collected. Old T-shirts or dress shirts produce less navel fuzz than brand new T-shirts. Using elemental analysis, it could be shown that cotton lint contains a certain amount of foreign material, supposedly cutaneous scales, fat or proteins. Incidentally, lint might thus fulfill a cleaning function for the navel.

Performance evaluation of drip-fertigated cotton grown under different plant densities using nuclear techniques

International Nuclear Information System (INIS)

Janat, M.; Kalhout, A.

2007-04-01

Field experiment was conducted over two growing seasons to assess different planting densities of cotton variety Aleppo 118 (71.000, 57.000, 48.000, 41.000, 33.500 plants /ha), and two irrigation systems; one irrigation line per one planting row and one irrigation line per two planting rows. Nitrogen fertilizer (120 kg N/ha) as Urea (46% N) was injected through the irrigation system in six equally split applications. A labeled area (1.0 m 2 ) was established for the labeled sub plots and labeled Urea was applied to the labeled sub plots in the same manner as for unlabeled N fertilizer. Irrigation scheduling was accomplished using the direct method of neutron scattering technique. Irrigation was determined when the soil moisture content in the active root depth reached almost 80% of the field capacity. The amount of water applied for one line / one row were 6738 and 9149 m 3 /ha, whereas, for one line/two rows were 7489 and 12653 m 3 / ha for the two growing seasons 2004 and 2005 respectively. The objectives of the experiment were to evaluate the effect of different planting densities and two irrigation system on cotton yield, lint properties, dry matter yield, N-uptake, chlorophyll content and leaf area. The experimental design was randomized block design with 6 replications for each irrigation method. Results revealed that no significant differences between all different plant densities were recorded for all growth parameters tested in this study such as seed cotton yield, dry matter yield, lint properties, chlorophyll content and leaf area.(author)

Effect of a Terminated Cover Crop and Aldicarb on Cotton Yield and Meloidogyne incognita Population Density.

Science.gov (United States)

Wheeler, T A; Leser, J F; Keeling, J W; Mullinix, B

2008-06-01

Terminated small grain cover crops are valuable in light textured soils to reduce wind and rain erosion and for protection of young cotton seedlings. A three-year study was conducted to determine the impact of terminated small grain winter cover crops, which are hosts for Meloidogyne incognita, on cotton yield, root galling and nematode midseason population density. The small plot test consisted of the cover treatment as the main plots (winter fallow, oats, rye and wheat) and rate of aldicarb applied in-furrow at-plant (0, 0.59 and 0.84 kg a.i./ha) as subplots in a split-plot design with eight replications, arranged in a randomized complete block design. Roots of 10 cotton plants per plot were examined at approximately 35 days after planting. Root galling was affected by aldicarb rate (9.1, 3.8 and 3.4 galls/root system for 0, 0.59 and 0.84 kg aldicarb/ha), but not by cover crop. Soil samples were collected in mid-July and assayed for nematodes. The winter fallow plots had a lower density of M. incognita second-stage juveniles (J2) (transformed to Log(10) (J2 + 1)/500 cm(3) soil) than any of the cover crops (0.88, 1.58, 1.67 and 1.75 Log(10)(J2 + 1)/500 cm(3) soil for winter fallow, oats, rye and wheat, respectively). There were also fewer M. incognita eggs at midseason in the winter fallow (3,512, 7,953, 8,262 and 11,392 eggs/500 cm(3) soil for winter fallow, oats, rye and wheat, respectively). Yield (kg lint per ha) was increased by application of aldicarb (1,544, 1,710 and 1,697 for 0, 0.59 and 0.84 kg aldicarb/ha), but not by any cover crop treatments. These results were consistent over three years. The soil temperature at 15 cm depth, from when soils reached 18 degrees C to termination of the grass cover crop, averaged 9,588, 7,274 and 1,639 centigrade hours (with a minimum threshold of 10 degrees C), in 2005, 2006 and 2007, respectively. Under these conditions, potential reproduction of M. incognita on the cover crop did not result in a yield penalty.

Utilization of cotton waste for regenerated cellulose fibres: Influence of degree of polymerization on mechanical properties.

Science.gov (United States)

De Silva, Rasike; Byrne, Nolene

2017-10-15

Cotton accounts for 30% of total fibre production worldwide with over 50% of cotton being used for apparel. In the process from cotton bud to finished textile product many steps are required, and significant cotton waste is generated. Typically only 30% of pre consumer cotton is recycled. Here we use cotton waste lint to produce regenerated cellulose fibres (RCF). We find the RCF from waste cotton lint had increased mechanical properties compared to RCF produced from wood pulp. We show that this is likely linked to the higher degree of polymerization (DP) of waste cotton lint. An ionic liquid is used to dissolve the cotton lint and the rheology of the spinning is measured. The properties of the RCF are characterized and compared to wood pulp RCF. Copyright © 2017 Elsevier Ltd. All rights reserved.

Stability analysis for yield and some other traits in egyptian cotton genotypes across varying environments

International Nuclear Information System (INIS)

Shaheen, A.M.A.; Gomaa, M.A.M.; Khattab, S.A.M.

1999-01-01

Data obtained from eight genotypes of cotton grown over two successive seasons each included three nitrogen levels i.e. 45, 60 and 75kg nitrogen/feddan were statistically analysed using stability model. Ten quantitative traits were studied to indicate the performance of genotypes, comprised seed cotton yiel/plant, number of bolls/plant, average boll weight, lint percentage, fiber length (2.5%SL), fiber length (50%SL), uniformity ratio, micronair value, fiber strength and oil percentage. stability parameters (b) and (S 2 d) were used to compare the performance of these ge notypes over environment. Genotypes were ranked according to significance of their stability parameters for studied characters. The best genotype according to stability was the genotype 3/28/1 and the worst one was Giza 81

Performance of cotton leaf curl virus resistant intrahirsutum f/sub 1/ hybrids

International Nuclear Information System (INIS)

Baloch, M.J.

2004-01-01

The first and foremost effort to combat the devastating cotton leaf curl virus (clcv) disease would be to utilize those clcv resistant germplasm in a hybridization programme which can enhance the possibilities of selecting desirable progenies from segregating populations. In this connection, 16 clcv intrahirsutum F1 hybrids were developed and evaluated for their performance. The hybrids, on an average gave an increase of 26.02 % in seed cotton yield; 11.52 % in bolls per plant; 14.23 % in boll weight; 4.28 % in lint; 3.89 % in fibre length and 8.21 % in earliness against the average of parents. However, among the hybrids, the top three scoring for yield were, BH.121 x Cyto.9/91, Cyto.9/91 x CRIS-226 and VH-137 x CRIS-226. The number of bolls per plant was found to be a major contributing factor for increased yield because the hybrids which set higher bolls correspondingly gave higher yields. Boll weight was not regarded as an important attribute to increase yield because hybrids with moderate boll sizes were among the top three high yielders. For lint %, the hybrids CRIS-129 x LRA-5166 and FH-901 x VH-137 were first for fibre length, whereas CRIS-121 x Cyto.51 and BH-124 x CIM-448 were among the top two rankers. Regarding earliness, the hybrids CRIS-121 x Cyto. 51 gave the highest boll opening percent and next in order was the hybrid VH-137 x DNH-49. Our results thus generally suggest that although the best three hybrids were desirable for other traits, the choice of the hybrids may be made on the priority for characters to be bred. (author)

Estimation of Heterosis and Combining Ability in F1 Hybrids of Upland Cotton for Yield and Fiber Traits

International Nuclear Information System (INIS)

Arain, B.T.; Baloch, M.J.; Bughio, Q.U.A.; Sial, P.; Arain, M.A.; Baloch, A.

2015-01-01

The experimental research was conducted so as to determine the general combining ability (GCA) and specific combining ability (SCA) estimates and heterotic effects for seed cotton yield and fibre traits in 5 x 5 half diallel crosses of upland cotton (Gossypium hirsutum L.). The parental genotypes studied were; CRIS-134, IR-3701, IR-1524, FH-113 and MG-6. The characters such as bolls/plant, sympodial branches/plant, boll weight (g), plant height (cm), fibre length (mm), seed cotton yield/plant (g), seed index (g) and ginning out turn percentage were studied. The experiment was laid-out in a randomized complete block design with four replications at experimental field of the Department of Plant Breeding and Genetics, Sindh Agriculture University Tandojam, Pakistan during 2013. The results revealed that, parents and hybrids differed significantly for their mean performance regarding all the traits studied. The importance of heterotic effects was evident from the significance of parents vs. hybrids performance. The variances due to GCA and SCA were significant for all the traits except that GCA was non-significant for boll weight only whereas, SCA was non-significant for boll weight, seed index and ginning out turn percentage. The significance of GCA indicated the importance of additive genes advocating the traits while, the involvement of non-additive genes was evident from the significance of SCA variances. The GCA variances were greater than SCA for bolls per plant, plant height, seed cotton yield and lint percentage while, SCA variances were higher than GCA for sympodial branches/plant and fibre length. Parents IR-3701, FH-113 and MG-6 displayed higher positive GCA effects for bolls/plant, sympodial branches/plant, fibre length, seed cotton yield, seed index and ginning out turn percentage. The per se performance of these three parents was exactly reflected in their GCA effects and such happenings are exceptional. Such results suggested that, all three parents were

7 CFR 1427.1203 - Eligible ELS cotton.

Science.gov (United States)

2010-01-01

... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Extra Long Staple (ELS) Cotton... must be either: (1) Baled lint, including baled lint classified by USDA's Agricultural Marketing..., under the provisions of this subpart, has been made available; (2) Imported ELS cotton; (3) Raw...

Fourier-transform imaging of cotton and botanical and field trash mixtures

Science.gov (United States)

Botanical and field cotton trash comingled with cotton lint can greatly reduce the marketability and quality of cotton. Trash can be found comingled with cotton lint during harvesting, ginning, and processing, thus this study is of interest. Attenuated Total Reflectance-Fourier Transform Infrared (A...

Impacts of Alterations of Organic Inputs on the Bacterial Community within the sediments of Wind Cave, South Dakota, USA

Directory of Open Access Journals (Sweden)

Chelius Marisa K.

2009-01-01

Full Text Available Wind Cave (WICA in the Black Hills of South Dakota, like many mostly dry caves in temperate regions is an energy-starved system.The biotic communities that reside in these systems are low in diversity and simple in structure, and sensitive to changes in externalinputs of organic matter. Caves open to tourist traffic offer an opportunity to study the impacts of organic matter amendments in theform of human and rodent hair and dander, clothing lint, material from rodent activity (nesting materials and feces, and algal growthin and around artificial lighting. This study reports on the impacts of carbon amendments from humans and rodents on the bacterialand archaeal communities within the sediments of WICA from annual surveys and from a manipulative study that added lint (‘L’;cellulose plus rodent dander and rodent hair, rodent feces (‘F’, and a combination of both (‘LF’. The survey confirmed that bacterialbiomass was higher in regions of the cave with the highest rates of lint (hair and natural clothing fibers input. The manipulative studyfound that organic amendments in the forms of lint (L and rodent feces (F altered the WICA bacterial community structure in bothabundance and diversity, with the combined lint and feces (LF amendment having the most significant response. The high similarityof the LF and L communities suggests that the cave bacterial community is more carbon than nitrogen limited. The implication ofcave development to management practices is immediate and practical. Even small amounts of lint and organic matter foreign tocave bacteria significantly compromise the integrity of the endemic community resulting in the replacement of undescribed speciesby assemblages with at best, unknown impacts to natural cave features.

Estimation of best parents parents and superior cross combinations for yield and fiber quality related traits in upland cotton (gossypium hirsutum L.)

International Nuclear Information System (INIS)

Shaukat, S.; Khan, T.M.; Ijaz, S.

2013-01-01

Combining ability was studied for identification of potential cultivars and hybrids in upland cotton (Gossypium hirsutum L.) in a 6x6 set of diallel crosses among six genotypes of cotton, i.e., VH-232, CRS-2007, SB-149, GR-156, FH-207, and MARVI carried out on fiber length, fiber fineness, fiber elongation, fiber strength, ginning out tern (GOT) and seed cotton yield. Analysis of variance revealed highly significant (p < 0.01) differences among the genotypes for all traits. Combining ability studies showed that the mean squares, due to general combining ability (GCA), specific combining ability (SCA) and reciprocal effects were highly significant in F1 generation. Genetic components, due to GCA and SCA, revealed that traits, such as, fiber length, strength and fineness, showed high proportion of additive type of gene action in F1 generation because of greater GCA variances were greater than SCA variance. GR-156 was the best combiner for lint percentage and fiber length. FH-207 was the best combiner for fiber fineness. FH-207, MARVI and SB-149 were the best general combiners for fiber character and were suggested to be used in future breeding programme to improve fiber quality traits. CRS-2007 x GR-156, CRS-2007 x MARVI, SB-149 x MARVI and VH-232 x SB-149 had higher specific combining ability and reciprocal effects and they can be used for future breeding programme to improve fiber quality. (author)

Turbulent Mixing and Combustion for High-Speed Air-Breathing Propulsion Application

Science.gov (United States)

2007-08-12

viscous calculation .it Ott ~= 0.5 (left) and I./(/= 1.4 (right 1. bihluc lines,) at Re=70( and UI./= I .0. 066307-7 BERGTIIORSC)N ct ed. P~HYSICAL RFNEWlEV...a ttd I /d= 1 4 (dash- error fuineti ott 111111- aind inca-sured. % . eloci ties. nornual i/ed by ttOtU ble- dlotted linte)I. the Bernoulli velocitv...binned to 344 x 260 pix 2; a binned pixel yields good profile statistics. maps into 46 pim in the flow). A 70 ns gate time re- Figure 3 shows an

Water quality of surface runoff and lint yield in cotton under furrow irrigation in Northeast Arkansas

Science.gov (United States)

Use of furrow irrigation in row crop production is a common practice through much of the Midsouth US and yet, nutrients can be transported off-site through surface runoff. A field study with cotton (Gossypium hirsutum, L.) was conducted to understand the impact of furrow tillage practices and nitrog...

Brazilian Soybean Yields and Yield Gaps Vary with Farm Size

Science.gov (United States)

Jeffries, G. R.; Cohn, A.; Griffin, T. S.; Bragança, A.

2017-12-01

Understanding the farm size-specific characteristics of crop yields and yield gaps may help to improve yields by enabling better targeting of technical assistance and agricultural development programs. Linking remote sensing-based yield estimates with property boundaries provides a novel view of the relationship between farm size and yield structure (yield magnitude, gaps, and stability over time). A growing literature documents variations in yield gaps, but largely ignores the role of farm size as a factor shaping yield structure. Research on the inverse farm size-productivity relationship (IR) theory - that small farms are more productive than large ones all else equal - has documented that yield magnitude may vary by farm size, but has not considered other yield structure characteristics. We examined farm size - yield structure relationships for soybeans in Brazil for years 2001-2015. Using out-of-sample soybean yield predictions from a statistical model, we documented 1) gaps between the 95th percentile of attained yields and mean yields within counties and individual fields, and 2) yield stability defined as the standard deviation of time-detrended yields at given locations. We found a direct relationship between soy yields and farm size at the national level, while the strength and the sign of the relationship varied by region. Soybean yield gaps were found to be inversely related to farm size metrics, even when yields were only compared to farms of similar size. The relationship between farm size and yield stability was nonlinear, with mid-sized farms having the most stable yields. The work suggests that farm size is an important factor in understanding yield structure and that opportunities for improving soy yields in Brazil are greatest among smaller farms.

Optimizing rice yields while minimizing yield-scaled global warming potential.

Science.gov (United States)

Pittelkow, Cameron M; Adviento-Borbe, Maria A; van Kessel, Chris; Hill, James E; Linquist, Bruce A

2014-05-01

To meet growing global food demand with limited land and reduced environmental impact, agricultural greenhouse gas (GHG) emissions are increasingly evaluated with respect to crop productivity, i.e., on a yield-scaled as opposed to area basis. Here, we compiled available field data on CH4 and N2 O emissions from rice production systems to test the hypothesis that in response to fertilizer nitrogen (N) addition, yield-scaled global warming potential (GWP) will be minimized at N rates that maximize yields. Within each study, yield N surplus was calculated to estimate deficit or excess N application rates with respect to the optimal N rate (defined as the N rate at which maximum yield was achieved). Relationships between yield N surplus and GHG emissions were assessed using linear and nonlinear mixed-effects models. Results indicate that yields increased in response to increasing N surplus when moving from deficit to optimal N rates. At N rates contributing to a yield N surplus, N2 O and yield-scaled N2 O emissions increased exponentially. In contrast, CH4 emissions were not impacted by N inputs. Accordingly, yield-scaled CH4 emissions decreased with N addition. Overall, yield-scaled GWP was minimized at optimal N rates, decreasing by 21% compared to treatments without N addition. These results are unique compared to aerobic cropping systems in which N2 O emissions are the primary contributor to GWP, meaning yield-scaled GWP may not necessarily decrease for aerobic crops when yields are optimized by N fertilizer addition. Balancing gains in agricultural productivity with climate change concerns, this work supports the concept that high rice yields can be achieved with minimal yield-scaled GWP through optimal N application rates. Moreover, additional improvements in N use efficiency may further reduce yield-scaled GWP, thereby strengthening the economic and environmental sustainability of rice systems. © 2013 John Wiley & Sons Ltd.

Effect of Integrated Nutrient Management on Yield and Yield ...

African Journals Online (AJOL)

Declining soil fertility is one of the major problems causing yield reduction of barley ... (VC) with inorganic NP on growth, yield and yield components of food barley. ... The experiments were laid out in a randomized complete block design with ...

Yield trends and yield gap analysis of major crops in the world

OpenAIRE

Hengsdijk, H.; Langeveld, J.W.A.

2009-01-01

This study aims to quantify the gap between current and potential yields of major crops in the world, and the production constraints that contribute to this yield gap. Using an expert-based evaluation of yield gaps and the literature, global and regional yields and yield trends of major crops are quantified, yield gaps evaluated by crop experts, current yield progress by breeding estimated, and different yield projections compared. Results show decreasing yield growth for wheat and rice, but ...

Equity yields

NARCIS (Netherlands)

Vrugt, E.; van Binsbergen, J.H.; Koijen, R.S.J.; Hueskes, W.

2013-01-01

We study a new data set of dividend futures with maturities up to ten years across three world regions: the US, Europe, and Japan. We use these asset prices to construct equity yields, analogous to bond yields. We decompose the equity yields to obtain a term structure of expected dividend growth

Comparative Transcriptomics Reveals Jasmonic Acid-Associated Metabolism Related to Cotton Fiber Initiation.

Directory of Open Access Journals (Sweden)

Liman Wang

Full Text Available Analysis of mutants and gene expression patterns provides a powerful approach for investigating genes involved in key stages of plant fiber development. In this study, lintless-fuzzless XinWX and linted-fuzzless XinFLM with a single genetic locus difference for lint were used to identify differentially expressed genes. Scanning electron microscopy showed fiber initiation in XinFLM at 0 days post anthesis (DPA. Fiber transcriptional profiling of the lines at three initiation developmental stages (-1, 0, 1 DPA was performed using an oligonucleotide microarray. Loop comparisons of the differentially expressed genes within and between the lines was carried out, and functional classification and enrichment analysis showed that gene expression patterns during fiber initiation were heavily associated with hormone metabolism, transcription factor regulation, lipid transport, and asparagine biosynthetic processes, as previously reported. Further, four members of the allene-oxide cyclase (AOC family that function in jasmonate biosynthesis were parallel up-regulation in fiber initiation, especially at -1 DPA, compared to other tissues and organs in linted-fuzzed TM-1. Real time-quantitative PCR (RT-qPCR analysis in different fiber mutant lines revealed that AOCs were up-regulated higher at -1 DPA in lintless-fuzzless than that in linted-fuzzless and linted-fuzzed materials, and transcription of the AOCs was increased under jasmonic acid (JA treatment. Expression analysis of JA biosynthesis-associated genes between XinWX and XinFLM showed that they were up-regulated during fiber initiation in the fuzzless-lintless mutant. Taken together, jasmonic acid-associated metabolism was related to cotton fiber initiation. Parallel up-regulation of AOCs expression may be important for normal fiber initiation development, while overproduction of AOCs might disrupt normal fiber development.

Yield, yield components and dry matter digestibility of alfalfa experimental populations

Directory of Open Access Journals (Sweden)

Katić Slobodan

2010-01-01

Full Text Available Alfalfa is the most important forage crop grown in the temperate regions. It is cultivated for production of vegetative aerial mass used fresh or as hay, and recently as haylage and silage. In many centres worldwide, efforts are made to breed and create new alfalfa cultivars with both higher yields and of higher nutritional value. The aim of this paper was to determine yield and digestibility of 12 experimental populations of alfalfa, and to compare their results to the yields of well-known domestic alfalfa commercial cultivars. The results show significant differences in yield of green forage and dry matter among alfalfa populations, as well as in yield components, height, proportion of leaves in yield and growth rate (tab. 1, 2 and 3. Differences between in vitro digestible dry matter (% and yields of in vitro digestible dry matter (t ha-1 were also significant (tab. 5 and 6. Yield and quality of experimental populations were at the same level or higher than of control cultivars. Synthetic SINUSA exceeded the control cutivars (NS Mediana ZMS V and Banat VS in yield and quality of dry matter. .

Slope Controls Grain Yield and Climatic Yield in Mountainous Yunnan province, China

Science.gov (United States)

Duan, X.; Rong, L.; Gu, Z.; Feng, D.

2017-12-01

Mountainous regions are increasingly vulnerable to food insecurity because of limited arable land, growing population pressure, and climate change. Development of sustainable mountain agriculture will require an increased understanding of the effects of environmental factors on grain and climatic yields. The objective of this study was to explore the relationships between actual grain yield, climatic yield, and environmental factors in a mountainous region in China. We collected data on the average grain yield per unit area in 119 counties in Yunnan province from 1985 to 2012, and chose 17 environmental factors for the same period. Our results showed that actual grain yield ranged from 1.43 to 6.92 t·ha-1, and the climatic yield ranged from -0.15 to -0.01 t·ha-1. Lower climatic yield but higher grain yield was generally found in central areas and at lower slopes and elevations in the western and southwestern counties of Yunnan province. Higher climatic yield but lower grain yield were found in northwestern parts of Yunnan province on steep slopes. Annual precipation and temperature had a weak influence on the climatic yield. Slope explained 44.62 and 26.29% of the variation in grain yield and climatic yield. The effects of topography on grain and climatic yields were greater than climatic factors. Slope was the most important environmental variable for the variability in climatic and grain yields in the mountainous Yunnan province due to the highly heterogeneous topographic conditions. Conversion of slopes to terraces in areas with higher climatic yields is an effective way to maintain grain production in response to climate variability. Additionally, soil amendments and soil and water conservation measures should be considered to maintain soil fertility and aid in sustainable development in central areas, and in counties at lower slopes and elevations in western and southwestern Yunnan province.

Stink Bug Feeding Induces Fluorescence in Developing Cotton Bolls

Directory of Open Access Journals (Sweden)

Toews Michael D

2011-08-01

Full Text Available Abstract Background Stink bugs (Hemiptera: Pentatomidae comprise a critically important insect pest complex affecting 12 major crops worldwide including cotton. In the US, stink bug damage to developing cotton bolls causes boll abscission, lint staining, reduced fiber quality, and reduced yields with estimated losses ranging from 10 to 60 million dollars annually. Unfortunately, scouting for stink bug damage in the field is laborious and excessively time consuming. To improve scouting accuracy and efficiency, we investigated fluorescence changes in cotton boll tissues as a result of stink bug feeding. Results Fluorescent imaging under long-wave ultraviolet light showed that stink bug-damaged lint, the inner carpal wall, and the outside of the boll emitted strong blue-green fluorescence in a circular region near the puncture wound, whereas undamaged tissue emissions occurred at different wavelengths; the much weaker emission of undamaged tissue was dominated by chlorophyll fluorescence. We further characterized the optimum emission and excitation spectra to distinguish between stink bug damaged bolls from undamaged bolls. Conclusions The observed characteristic fluorescence peaks associated with stink bug damage give rise to a fluorescence-based method to rapidly distinguish between undamaged and stink bug damaged cotton bolls. Based on the fluorescent fingerprint, we envision a fluorescence reflectance imaging or a fluorescence ratiometric device to assist pest management professionals with rapidly determining the extent of stink bug damage in a cotton field.

Use of radiation induction to improve new cotton lines resistant to Heliothis armigera

Energy Technology Data Exchange (ETDEWEB)

Hormchan, P [Dept. of Entomology, Faculty of Agriculture, Kasetsart Univ., Bangkok (Thailand); Wongpiyasatid, A [Dept. of Applied and Isotopes Faculty fo Science, Kasetsart Univ., Bangkok (Thailand)

1996-12-01

Ratchada 1 (R{sub 1}) seeds irradiated with 300 gray of gamma rays in order to obtain new cotton lines resistant to the American bollworm with high yield and good quality were compared with Srisamrong 2 (SR{sub 1}) and Ratchada 1 (R{sub 1}), the present recommended varieties to the farmers. The experiments were conducted under both laboratory and field conditions for 3 consecutive years and 2 new lines, A P{sub 1} and A P{sub 2} in M{sub 5} with the required attribute, were finally selected. In the lab, after feeding 2 nd instar bollworm larvae with young leaves of tested lines and the controls the increased weight, larval length, pupal weight of new lines were found to be better than those of SR{sub 2} and R{sub 1} including % gossypol and flavonoids, the substances being expected to give antibiotic effect to the insects. Physical aberration was also noticed in A P{sub 1}. As of the field condition, with the similar amount of bollworm numbers, the 10 fresh boll weight, lint weight, seed weight, % lint, micronaire fibre strength, and fibre length were found to be higher and better than those of both controls as well. However, further tests in large scale of farmers` field a period of time will have to be undertaken to ascertain the result

Yield trends and yield gap analysis of major crops in the world

NARCIS (Netherlands)

Hengsdijk, H.; Langeveld, J.W.A.

2009-01-01

This study aims to quantify the gap between current and potential yields of major crops in the world, and the production constraints that contribute to this yield gap. Using an expert-based evaluation of yield gaps and the literature, global and regional yields and yield trends of major crops are

On yield gaps and yield gains in intercropping

NARCIS (Netherlands)

Gou, Fang; Yin, Wen; Hong, Yu; Werf, van der Wopke; Chai, Qiang; Heerink, Nico; Ittersum, van Martin K.

2017-01-01

Wheat-maize relay intercropping has been widely used by farmers in northwest China, and based on field experiments agronomists report it has a higher productivity than sole crops. However, the yields from farmers’ fields have not been investigated yet. Yield gap analysis provides a framework to

Water use, canopy temperature, lint yield, and fiber quality response of six upland cotton cultivars to water stress

Science.gov (United States)

The declining saturated thickness of the Ogallala Aquifer combined with the unpredictability of precipitation during the growing season in the Southern High Plains has resulted in elevated production risks associated with short-term crop water deficits. Cotton (Gossypium spp.) cultivars that can use...

VARIABILITY OF YIELD AND YIELD COMPONENTS IN “EGUSI ...

African Journals Online (AJOL)

journal

Estimate of expected genetic advance in seed yield plant-1 ranged between. 25.90-48.40%. ..... values in fruit and seed yield characters have been reported in culinary melon, ... and Khund, A. 2004. Extent of heterosis and heritability in some.

Fission product yields

International Nuclear Information System (INIS)

Valenta, V.; Hep, J.

1978-01-01

Data are summed up necessary for determining the yields of individual fission products from different fissionable nuclides. Fractional independent yields, cumulative and isobaric yields are presented here for the thermal fission of 235 U, 239 Pu, 241 Pu and for fast fission (approximately 1 MeV) of 235 U, 238 U, 239 Pu, 241 Pu; these values are included into the 5th version of the YIELDS library, supplementing the BIBFP library. A comparison is made of experimental data and possible improvements of calculational methods are suggested. (author)

yield and yield componemts of extra early maize (zea mays l.)

African Journals Online (AJOL)

SHARIFAI

maize crop and improve the soil structures and chemical nutrients of the soil. The significant interaction between intra-row spacing and poultry manure on cob diameter, 100 grain weight and grain yield showed the importance of poultry manure on yield and yield components of maize crop. Poultry manure increases both ...

An adapted yield criterion for the evolution of subsequent yield surfaces

Science.gov (United States)

Küsters, N.; Brosius, A.

2017-09-01

In numerical analysis of sheet metal forming processes, the anisotropic material behaviour is often modelled with isotropic work hardening and an average Lankford coefficient. In contrast, experimental observations show an evolution of the Lankford coefficients, which can be associated with a yield surface change due to kinematic and distortional hardening. Commonly, extensive efforts are carried out to describe these phenomena. In this paper an isotropic material model based on the Yld2000-2d criterion is adapted with an evolving yield exponent in order to change the yield surface shape. The yield exponent is linked to the accumulative plastic strain. This change has the effect of a rotating yield surface normal. As the normal is directly related to the Lankford coefficient, the change can be used to model the evolution of the Lankford coefficient during yielding. The paper will focus on the numerical implementation of the adapted material model for the FE-code LS-Dyna, mpi-version R7.1.2-d. A recently introduced identification scheme [1] is used to obtain the parameters for the evolving yield surface and will be briefly described for the proposed model. The suitability for numerical analysis will be discussed for deep drawing processes in general. Efforts for material characterization and modelling will be compared to other common yield surface descriptions. Besides experimental efforts and achieved accuracy, the potential of flexibility in material models and the risk of ambiguity during identification are of major interest in this paper.

Inheritance of grain yield and its correlation with yield components in ...

African Journals Online (AJOL)

SAM

2014-03-19

Mar 19, 2014 ... 7 × 7 incomplete diallel cross of seven wheat parents during the crop season of 2009 to 2010. Mean square of general ... Genetic background and yield traits of the seven parents. Parent. Pedigree. Released year ..... Correlation and path analysis for yield and yield contributing characters in wheat (Triticum ...

Nomenclature, variation, and the biological species concept in Lamasina (Lycaenidae: Theclinae: Eumaeini Nomenclatura, variação e o conceito biológico de espécie em Lamasina (Lycaenidae: Theclinae: Eumaeini

Directory of Open Access Journals (Sweden)

Robert K. Robbins

2008-03-01

Full Text Available The correct generic name for the species that belong to Eucharia Boisduval, 1870, a homonym, is either Annamaria D'Abrera & Bálint, 2001, which has been considered to be unavailable, or Lamasina Robbins, 2002, a replacement name for Eucharia. A recent re-interpretation of the original description of Annamaria was incorrect, and Annamaria is confirmed as being unavailable under Article 13.1 of the Code. A proposed neotype for Papilio ganimedes Cramer, 1775 is invalidated, and a possible syntype is illustrated. Results of an analysis of variation in the Lamasina ganimedes complex are distinctly different from those previously published and provide insufficient evidence to support the hypothesis that L. lathyi (Bálint, 2005 is distinct under a biological species concept. Lamasina lathyi is a synonym of L. ganimedes syn. nov. Statistical evidence overwhelmingly falsifies the published hypothesis that the L. rhaptissima (Johnson, 1991 (14 males and L. columbia (Bálint, 2005 (8 females species complexes are distinct rather than males and females of the same complex. Lamasina columbia is endemic to western Colombia. The hypothesis that L. rhapsodia (Bálint, 2005 from Bolivia is a distinct species is not better supported than the hypotheses that the one known specimen of L. rhapsodia is a geographical variant or an aberrant specimen. Lamasina rhapsodia is a synonym of L. rhaptissima syn. nov. Superficial similarity in ventral wing patterns in genera Paiwarria Kaye, 1904 and Lamasina is noted. A nomenclatural checklist for Lamasina is presented.O nome genérico correto para as espécies de Eucharia Boisduval, 1870, um homônimo, é Annamaria D'Abrera & Bálint, 2001, que tem sido considerado não válido, ou Lamasina Robbins, 2002, um nome substituto para Eucharia. Uma reinterpretação recente da descrição original de Annamaria é considerada incorreta, confirmando a não disponibilidade do nome com base no Artigo 13.1 do Código. O neótipo de

Effects of cutting frequency on alfalfa yield and yield components in ...

African Journals Online (AJOL)

Effects of cutting frequency on alfalfa yield and yield components in Songnen Plain, Northeast China. J Chen, F Tang, R Zhu, C Gao, G Di, Y Zhang. Abstract. The productivity and quality of alfalfa (Medicago sativa L.) is strongly influenced by cutting frequency (F). To clarify that the yield and quality of alfalfa if affected by F, ...

Bond yield curve construction

Directory of Open Access Journals (Sweden)

Kožul Nataša

2014-01-01

Full Text Available In the broadest sense, yield curve indicates the market's view of the evolution of interest rates over time. However, given that cost of borrowing it closely linked to creditworthiness (ability to repay, different yield curves will apply to different currencies, market sectors, or even individual issuers. As government borrowing is indicative of interest rate levels available to other market players in a particular country, and considering that bond issuance still remains the dominant form of sovereign debt, this paper describes yield curve construction using bonds. The relationship between zero-coupon yield, par yield and yield to maturity is given and their usage in determining curve discount factors is described. Their usage in deriving forward rates and pricing related derivative instruments is also discussed.

7755 EFFECT OF NPK FERTILIZER ON FRUIT YIELD AND YIELD ...

African Journals Online (AJOL)

Win7Ent

2013-06-03

Jun 3, 2013 ... peasant farmers in Nigeria. With the increased ... did not significantly (p=0.05) increase the fruit yield nor the seed yield. Key words: NPK fertilizer, Fruit ..... SAS (Statistical Analysis System) Version 9.1. SAS Institute Inc., Cary, ...

Response of Yield and Yield Components of Tef [Eragrostis Tef ...

African Journals Online (AJOL)

The partial budget analysis also indicates that applications of 46 kg. N ha-1 and 10 kg P ha-1 are ..... (1994) indicated that where the grain yield response is negative, yield reduction is primarily caused by a .... An Economic Training. Manual.

Correlation and path-cofficient analysis of seed yield and yield ...

African Journals Online (AJOL)

This study was undertaken in order to determine the association among yield components and their direct and indirect effects on the seed yield of confectionery sunflower. 36 confectionery sunflower populations originated from different regions of Northwest Iran were characterized using 11 agromorphological traits ...

Soviet test yields

Science.gov (United States)

Vergino, Eileen S.

Soviet seismologists have published descriptions of 96 nuclear explosions conducted from 1961 through 1972 at the Semipalatinsk test site, in Kazakhstan, central Asia [Bocharov et al., 1989]. With the exception of releasing news about some of their peaceful nuclear explosions (PNEs) the Soviets have never before published such a body of information.To estimate the seismic yield of a nuclear explosion it is necessary to obtain a calibrated magnitude-yield relationship based on events with known yields and with a consistent set of seismic magnitudes. U.S. estimation of Soviet test yields has been done through application of relationships to the Soviet sites based on the U.S. experience at the Nevada Test Site (NTS), making some correction for differences due to attenuation and near-source coupling of seismic waves.

Effects of phosphorus and zinc applications on the yields and yields ...

African Journals Online (AJOL)

Effects of phosphorus and zinc applications on the yields and yields components of sole early maturing maize ( Zea mays ) and bambaranut ( Vigna subterranean Thour. ) and in intercrop under southern guinea savannah ecology zone.

6 Grain Yield

African Journals Online (AJOL)

create a favourable environment for rice ... developing lines adaptable to many ... have stable, not too short crop duration with ..... Analysis of variance of the effect of site and season on maturity, grain yield and plant ..... and yield components.

Using normalized difference vegetation index (NDVI) to estimate sugarcane yield and yield components

Science.gov (United States)

Sugarcane (Saccharum spp.) yield and yield components are important traits for growers and scientists to evaluate and select cultivars. Collection of these yield data would be labor intensive and time consuming in the early selection stages of sugarcane breeding cultivar development programs with a ...

Potato yield and yield structure depending on irrigation

Directory of Open Access Journals (Sweden)

Milić Stanko

2010-01-01

Full Text Available In the agroclimatic conditions of the Vojvodina Province, the application of an economic water regime and modern technology is necessary for stable and intensive potato production. A two-year experiment on calcareous chernozem was carried out to determine how irrigation and different pre-irrigation soil moisture affect potato yield and distribution of tuber fraction in the potato yield. The block-design trial had four replicates and was adapted for sprinkler irrigation conditions. It included four treatments: irrigation with pre-irrigation moisture levels of 60 % of field water capacity (FC, irrigation with pre-irrigation moisture levels of 70 % (FC, irrigation with pre-irrigation moisture levels of 80% (FC, and a non-irrigated control treatment. Irrigation significantly increased the yield of potato, which increased from 37.27 % to 75.86 %. Under irrigation, the percentage of small fractions decreased in favour of the 55 mm one, or fractions above the 45-55 mm range. On average, irrigated treatments produced significantly more tubers than the conditions of natural water supply. .

Comparing predicted yield and yield stability of willow and Miscanthus across Denmark

DEFF Research Database (Denmark)

Larsen, Søren; Jaiswal, Deepak; Bentsen, Niclas Scott

2016-01-01

was 12.1 Mg DM ha−1 yr−1 for willow and 10.2 Mg DM ha−1 yr−1 for Miscanthus. Coefficent of variation as a measure for yield stability was poorest on the sandy soils of northern and western Jutland and the year-to-year variation in yield was greatest on these soils. Willow was predicted to outyield...... Miscanthus on poor, sandy soils whereas Miscanthus was higher yielding on clay-rich soils. The major driver of yield in both crops was variation in soil moisture, with radiation and precipitation exerting less influence. This is the first time these two major feedstocks for northern Europe have been compared....... The semi-mechanistic crop model BioCro was used to simulate the production of both short rotation coppice (SRC) willow and Miscanthus across Denmark. Predictions were made from high spatial resolution soil data and weather records across this area for 1990-2010. The potential average, rain-fed mean yield...

Global evaluation of a semiempirical model for yield anomalies and application to within-season yield forecasting.

Science.gov (United States)

Schauberger, Bernhard; Gornott, Christoph; Wechsung, Frank

2017-11-01

Quantifying the influence of weather on yield variability is decisive for agricultural management under current and future climate anomalies. We extended an existing semiempirical modeling scheme that allows for such quantification. Yield anomalies, measured as interannual differences, were modeled for maize, soybeans, and wheat in the United States and 32 other main producer countries. We used two yield data sets, one derived from reported yields and the other from a global yield data set deduced from remote sensing. We assessed the capacity of the model to forecast yields within the growing season. In the United States, our model can explain at least two-thirds (63%-81%) of observed yield anomalies. Its out-of-sample performance (34%-55%) suggests a robust yield projection capacity when applied to unknown weather. Out-of-sample performance is lower when using remote sensing-derived yield data. The share of weather-driven yield fluctuation varies spatially, and estimated coefficients agree with expectations. Globally, the explained variance in yield anomalies based on the remote sensing data set is similar to the United States (71%-84%). But the out-of-sample performance is lower (15%-42%). The performance discrepancy is likely due to shortcomings of the remote sensing yield data as it diminishes when using reported yield anomalies instead. Our model allows for robust forecasting of yields up to 2 months before harvest for several main producer countries. An additional experiment suggests moderate yield losses under mean warming, assuming no major changes in temperature extremes. We conclude that our model can detect weather influences on yield anomalies and project yields with unknown weather. It requires only monthly input data and has a low computational demand. Its within-season yield forecasting capacity provides a basis for practical applications like local adaptation planning. Our study underlines high-quality yield monitoring and statistics as critical

THE INFLUENCE OF FERTILIZATION ON YIELD AND YIELD COMPONENT FORMATION OF SOYBEAN VARIETIES

Directory of Open Access Journals (Sweden)

Eva CANDRÁKOVÁ

2009-03-01

Full Text Available In 2005 and 2006, the influence of fertilization was investigated on forming of yield components and yield of three soybean varieties in sugar beet growing area. Varieties Korada, Supra and OAC Vision were grown. Number of plants per m2, number of pods per plant, number of seeds in pod, thousand seeds weight, yield of seeds, yield of stems and harvest index were examined. Variants of fertilization: I. non-fertilized control, II. LAV 27 % (40 kg ha-1 net nutrient of N in growing stage of first pair of true leaves unfolded, III. Humix komplet (rate 8 l.ha-1 applied in growing stage of first pair of true leaves unfolded (4 l.ha-1 and in growing stage of first flower buds visible (4 l.ha-1, IV. Humix komplet in rate 8 l.ha-1 applied in growing stage of first pair of true leaves unfolded. The yields of seeds and stems were high significantly influenced by variety, fertilization and year. The significantly highest yield of seeds was achieved by Korada variety (4,04 t.ha-1. Varieties OAC Vision and Supra reached yields in interval 3,74-3,84 t.ha-1. Split rate of Humix komplet (III var significantly influenced yield of seeds and stems. The fertilization have increased weight of seeds in proportion to aboveground phyto-mass weight, what was expressed by harvest index.

Effects of application boron on yields, yield component and oil ...

African Journals Online (AJOL)

The study was conducted to investigate the effects of five boron (B) doses; 0, 2.5, 5.0, 7.5 and 10.0 kg B ha-1 in B-deficient calcareous soils on yield and some yield components of four sunflower genotypes. Genotypes have shown variations with respect to their responses to B applications. AS-615 and Coban had the ...

Influence of Inter and Intra-rows Spacing on Yield and Yield ...

African Journals Online (AJOL)

Abyssinia

yield and yield components of fresh market(Bishola) and processing (Cochoro) tomato cultivars. ... row spacing had a significant effect on plan canopy width, above ground dry biomass, ... Poor varietal performance and management practices that includeinter and intra-row spacing ..... of assimilate export from the leaves.

Effects of heterosis for yield and yield components obtained by crossing divergent alfalfa populations

Directory of Open Access Journals (Sweden)

Katić Slobodan

2010-01-01

Full Text Available When breeding alfalfa for yield performance, it is necessary to use high-yielding parents obtained by different breeding methods. The assumption at the onset of this research was that crossing highest-yielding domestic cultivars with divergent populations from geographically distant breeding centers could result in the expression of heterotic effects in their hybrids contributing to increased alfalfa yield. The objective of this study was to determine yield and yield components and heterotic effects in hybrid progenies obtained by crossing the domestic cultivars NS Banat ZMS II and NS Mediana ZMS V with the cultivars Pella, Dolichi and Hyliki from Greece, UMSS 2001 from Bolivia and Jogeva 118 from Estonia in two series. The field trial planted in 2006, included 13 F1 hybrids and 6 of 7 initial parents in both series. Heterotic effects for yields of forage and hay were observed in 4 combinations (C NS Banat ZMS II x E Hyliki; C NS Banat ZMS II x E UMSS 2001; C NS Mediana ZMS V x E Hyliki; C NS Mediana ZMS V x E Dolichi. The populations that exhibited heterosis in a set of crossings are recommended for use as parent components for development of high-yielding synthetic alfalfa cultivars. .

Status of fission yield measurements

International Nuclear Information System (INIS)

Maeck, W.J.

1979-01-01

Fission yield measurement and yield compilation activities in the major laboratories of the world are reviewed. In addition to a general review of the effort of each laboratory, a brief summary of yield measurement activities by fissioning nuclide is presented. A new fast reactor fission yield measurement program being conducted in the US is described

Combining ability analysis in intraspecific f/sub 1/ diallel cross of upland cotton

International Nuclear Information System (INIS)

Khan, S.A.; Khan, N.U.; Mohammad, F.

2011-01-01

The research work comprised of combining ability and genetic variability in a 6 X 6 F1 diallel cross which was carried out during crop seasons 2008 and 2009 at Khyber Pakhtunkhwa Agricultural University, Peshawar, Pakistan. The parental genotypes (CIM-446, CIM-496, CIM-499, CIM-506, CIM-554 and CIM-707) were crossed in a complete diallel fashion during 2008. The 30 F1 hybrids and their parents were grown in a randomized complete block (RCB) design with three replications during 2009. Genotypes manifested significant (p less than or equal to 0.01) differences for days to first flowering, locules boll/sup -1/, seeds locule/sup -1/, lint % and seed cotton yield plant/sup -1/. The F1 hybrids showed significant increase over parents in mean values for all the traits. The correlation of seed cotton yield was significantly positive with majority of yield traits and negative with days to first flowering and lint %. Mean squares due to general (GCA) and specific combining ability (SCA) were highly significant for all the traits, except locules for GCA. Mean squares due to GCA were higher in magnitude than SCA for majority of the traits and their inheritance was mainly governed by additive type of gene action and partially by non-additive. Selection in such promising hybrids could be used in segregating generations, and also some specific cross combinations can be used for hybrid cotton production to increase the seed cotton yield. The best general combiners (CIM-446 and CIM-554) followed by CIM-496 and their utilization as one of the parents produced best specific F1 hybrids (CIM-446 X CIM-499, CIM-446 X CIM-554, CIM-496 X CIM-707 and CIM-506 X CIM-554) having valuable SCA determination and remarkable mean performance for most of the traits. Reciprocal crosses having prominent maternal effects also involved one of the general combiners for majority of the traits. The promising hybrids also exhibited earliness through which the crop can escape from pests attack and soil can

Measurements of fission yields

International Nuclear Information System (INIS)

Denschlag, H.O.

2000-01-01

After some historical introductory remarks on the discovery of nuclear fission and early fission yield determinations, the present status of knowledge on fission yields is briefly reviewed. Practical and fundamental reasons motivating the pursuit of fission yield measurements in the coming century are pointed out. Recent results and novel techniques are described that promise to provide new interesting insights into the fission process during the next century. (author)

Effect of sulfur and iron fertilizers on yield, yield components and ...

African Journals Online (AJOL)

Jane

2011-06-13

Jun 13, 2011 ... per plant. Interaction between water stress and combination of iron and sulfur fertilizers had significant .... Results of analysis of variance (ANOVA) of water stress (W), sulfur (B) and iron (C), and their interaction with gain yield, yield components and ... the soil structure and it increased the usefulness of other.

Effect of water stress on yield and yield components of sunflower ...

African Journals Online (AJOL)

A field experiment during year 2009 was conducted in the research station of the University of Tehran, College of Abouraihan in Pakdasht region, Iran. The study was aimed to investigate the effect of water stress on seed yield, yield component and some quantitative traits of four sunflower hybrids namely Azargol, Alstar, ...

Path coefficient and correlation of yield and yield associated traits in candidate bread wheat (triticum aestivum l)lines

International Nuclear Information System (INIS)

Muhammad, T.; Haider, S.; Qureshi, M. J.; Shah, G. S.; Zamir, R.

2005-01-01

Yield and yield contributing traits were studied in candidate bread wheat lines to find out the genetic contribution of the different characters towards grain yield at NIFA, Peshawar during 2001-02. All the characteristics studied differed significantly from each other. Days to heading showed negative and significant correlation with harvest index and grain yield but was negative and non-significant with the biological yield. Days to maturity were negatively correlated at both genotypic and phenotypic levels with biological yield; harvest index and grain yield and level of correlations were significant with harvest index and grain yield. Plant height showed negative genotypic and phenotypic correlation with harvest index and grain yield. Biological yield had positive and significant genotypic and phenotypic correlations with harvest index and grain yield. Harvest index had positive and highly significant genotypic and phenotypic correlation with grain yield. Genotypic and phenotypic correlation coefficients revealed that important characters influencing grain yield are harvest index and biological yield. Path analysis showed the importance in order of harvest index, biological yield, plant height, days to maturity and days to heading with grain yield. (author)

Pojushtshije tela / Eteri Kekelidze

Index Scriptorium Estoniae

Kekelidze, Eteri, 1944-

2007-01-01

10. apr. Kumu Kunstimuuseumis tantsuteatri Zick esituses etenduvast tantsulavastusest "Piaf", koreograafia ja kujunduse on teinud Dmitri Harchenko, video koostanud Einar Lints, valguskujundus Triin Hook

Seed yield and some yield components of sesame as affected by ...

African Journals Online (AJOL)

In order to study the effect of different irrigation, N and superabsorbent levels on yield and yield components of sesame, a field experiment was conducted in Khosf Region, Birjand, Iran in 2009 as a split-split plot design based on a randomized complete block design. The treatments included irrigation interval at three levels ...

Impacto do beneficiamento sobre o número de neps e quantidade de impurezas da fibra do algodão Ginning impact on the number of neps and amount of cotton fiber contaminants

Directory of Open Access Journals (Sweden)

Odilon R. R. F. da Silva

2010-01-01

Full Text Available Objetivou-se, neste trabalho, estudar o efeito do beneficiamento sobre o conteúdo de impurezas, pó e o número de neps na pluma, em 12 algodoeiras do Estado de Mato Grosso. O experimento consistiu de uma combinação fatorial de cinco etapas de beneficiamento do algodão em 12 algodoeiras em delineamento inteiramente casualizado com quatro repetições. Amostras de algodão foram coletadas nas seguintes etapas: a no desmanche do fardão; b antes do descaroçamento; c logo após o descaroçamento; d na bica, sem o uso do limpador tipo serrilha; e na bica, após a limpeza da pluma, utilizando-se o limpador tipo serrilha. Em todas as etapas se retiraram quatro amostras padrão de pluma com massa de 350 g a fim de serem analisadas mediante o instrumento AFIS (Advanced Fiber Information System para determinação do conteúdo de impurezas e poeira e o número de neps da fibra. Os resultados indicam que os processos de prelimpeza do algodão em caroço e limpeza da pluma reduzem o conteúdo de impurezas e da poeira do algodão enquanto, juntamente com o descaroçamento, esses processos aumentaram o número de neps da fibra do algodão. A utilização do limpador de pluma tipo serrilha com manta contínua aumenta a eficiência de limpeza da pluma, porém ocasiona incrementos significativos no número de neps.The purpose of this work was to study the ginning effect on the amount of cotton contaminants, dust and neps in cotton fiber, in 12 industries in the Mato Grosso State. The experiment consisted of a factorial combination over five stages of ginning and 12 cotton industries using a randomized design with four replications. Some samples of cotton were collected in the following phases: a in the bale dismantling; b before the ginning; c right after ginning; d into the covered lint slide not using the saw lint cleaner; and e into the covered lint slide, after cleaning process using the saw lint cleaner system. Over all stages four standard samples of

Box-Cox transformation for resolving Peelle's Pertinent Puzzle in curve fitting

International Nuclear Information System (INIS)

Oh, Soo-Youl

2003-01-01

Incorporating the Box-Cox transformation into a least-squares method is presented as one of resolutions of an anomaly known as Peelle's Pertinent Puzzle. The transformation is a strategy to make non-normal distribution data resemble normal data. A procedure is proposed: transform the measured raw data with an optimized Box-Cox transformation parameter, fit the transformed data using a usual curve fitting method, then inverse-transform the fitted results to final estimates. The generalized least-squares method utilized in GMA is adopted as the curve fitting tool for the test of proposed procedure. In the procedure, covariance matrices are correspondingly transformed and inverse-transformed with the aid of error propagation law. In addition to a sensible answer to the Peelle's problem itself, the procedure resulted in reasonable estimates of 6 Li(n,t) cross sections in several to 800 keV energy region. Meanwhile, comparisons of the present procedure with that of Chiba and Smith show that both procedures yield estimates so close each other for the sample evaluation on 6 Li(n,t) above as well as for the Peelle's problem. Two procedures, however, are conceptually very different and further discussions would be needed for a consensus on this issue of resolving the Puzzle. It is also pointed out that the transformation is applicable not only to a least-squares method but also to other parameter estimation method such as a usual Bayesian approach formulated with an assumption of normality of the probability density function. (author)

Influences of nitrogen and potassium top dressing on yield and yield ...

African Journals Online (AJOL)

STORAGESEVER

2010-05-03

May 3, 2010 ... (K) top dressing on grain yield and yield components of rice (Oryza sativa cv. Tarrom) and to ... positive reciprocal effect on crops, and was an important approach in ..... dressing fertilization (Figures 2a, b and c), but nitrogen levels of upper fully .... (Brassica napus L.)–rice (Oryza sativa L.) rotation. Plant Soil ...

Inheritance of grain yield and its correlation with yield components in ...

African Journals Online (AJOL)

SAM

2014-03-19

Mar 19, 2014 ... average yield of wheat in China is 4.75 t ha-1, which is low compared to other .... Analysis of variance for combining ability for grain yield plant-1. Source of variation ..... Hayman BI (1954). The theory and analysis of diallel crosses. .... Analysis and prospect of China wheat market in 2011. Food and Oil.

Effectiveness of neutral detergent fiber in whole cottonseed and dried distillers grains compared with alfalfa haylage.

Science.gov (United States)

Clark, P W; Armentano, L E

1993-09-01

Sixteen Holstein cows in midlactation were used in a 4 x 4 Latin square design to determine the effect of replacing alfalfa NDF with NDF from whole, linted cottonseed or dried distillers grains. Low and high fiber control diets (13 and 19% of dietary DM from alfalfa haylage NDF, respectively) were compared with diets designed to contain 13% of DM from alfalfa haylage NDF plus 6% of DM from either cottonseed NDF or distillers grains NDF. Dry matter intake, milk yield, and milk protein yield were lower from the high fiber control diet. Milk fat percentage was lower for the low fiber control diet. The cottonseed diet was equal to the high fiber control diet in stimulating rumination. Rumen acetate to propionate ratio was higher for the high fiber control and cottonseed diets. Replacing alfalfa with either of these high fiber by-product feeds increased feed intake and yields of milk fat and protein. The effectiveness of the NDF in distillers grains and cottonseed was not significantly different from that of alfalfa NDF for maintaining milk fat yield. Whole cottonseed and dried distillers grains appear to be good sources of effective fiber for maintaining milk fat test when they are substituted for alfalfa haylage fiber in lactating cow rations.

Effect of Biofertilizers on the Yield and Yield Components of Black Cumin (Nigella sativa L.

Directory of Open Access Journals (Sweden)

S Khorramdel

2011-02-01

Full Text Available Abstract Application of biological fertilizers is one of the most important methods for plant nutrition in ecological agriculture. In order to investigate the effect of biofertilizers on yield and yield components of black cumin (Nigella sativa L., a field experiment was arranged in a randomized complete block design with three replications during 2007 growing season at the Agricultural Research Station of Ferdowsi University of Mashhad. Treatments included: (A Azotobacter paspali, (B Azospirillum brasilense, (C the fungus of Glomus intraradaices, C+A, C+B, A+B, A+B+C, and control without no biofertilizers. In all treatments except control, the amounts of 15 mg of each biofertilizer were applied to 110 g of seeds. Results indicated that application of biofertilizers enhanced yield and yield components and decreased percentage of hollow capsules. Plant performance was better with application of Azospirillum plus mycorrhiza and a mixture of Azotobacter, Azospirillum and mycorrhiza in terms of yield determining criteria. The maximum and minimum amounts of seed yield were recorded in the B+C treatment with 41.4 gm-2, and control with 24.1 gm-2, respectively. There was no significant correlation between number of capsules per plant and seed yield, but the positive and significant correlation between number of branches per plant, number of seeds per capsule, 1000-seed weight and seed yield was observed. This study showed that application of suitable biofertilizers could increase yield and yield components of black cumin. Keywords: Biofertilizer, Ecological agriculture, Medicinal plants, Plant growth promoting rhizobacteria

Systematics of Fission-Product Yields

International Nuclear Information System (INIS)

Wahl, A.C.

2002-01-01

Empirical equations representing systematics of fission-product yields have been derived from experimental data. The systematics give some insight into nuclear-structure effects on yields, and the equations allow estimation of yields from fission of any nuclide with atomic number Z F = 90 thru 98, mass number A F = 230 thru 252, and precursor excitation energy (projectile kinetic plus binding energies) PE = 0 thru ∼200 MeV--the ranges of these quantities for the fissioning nuclei investigated. Calculations can be made with the computer program CYFP. Estimates of uncertainties in the yield estimates are given by equations, also in CYFP, and range from ∼ 15% for the highest yield values to several orders of magnitude for very small yield values. A summation method is used to calculate weighted average parameter values for fast-neutron (∼ fission spectrum) induced fission reactions

Systematics of Fission-Product Yields

Energy Technology Data Exchange (ETDEWEB)

A.C. Wahl

2002-05-01

Empirical equations representing systematics of fission-product yields have been derived from experimental data. The systematics give some insight into nuclear-structure effects on yields, and the equations allow estimation of yields from fission of any nuclide with atomic number Z{sub F} = 90 thru 98, mass number A{sub F} = 230 thru 252, and precursor excitation energy (projectile kinetic plus binding energies) PE = 0 thru {approx}200 MeV--the ranges of these quantities for the fissioning nuclei investigated. Calculations can be made with the computer program CYFP. Estimates of uncertainties in the yield estimates are given by equations, also in CYFP, and range from {approx} 15% for the highest yield values to several orders of magnitude for very small yield values. A summation method is used to calculate weighted average parameter values for fast-neutron ({approx} fission spectrum) induced fission reactions.

Locational variation in green fodder yield, dry matter yield, and forage quality of sorghum

International Nuclear Information System (INIS)

Hussain, A.; Khan, S.; Mohammad, D.

2007-01-01

The present study was designed to find out the variations in for- age yield and quality of sorghum as affected by different environments. The three agroecological zones viz., Agricultural Research Institute (ARI), Sariab, Quetta, Ayub Agricultural Research Institute (AARI), Faisalabad and National Agricultural Research Centre (NARC), Islamabad were selected on the basis of different physiography, geology, temperature, and climate and water availability. Crude protein contents, varied from 6.98 to 8.02 percent, crude fibre contents from 30.84 to 31.68 percent, green fodder yield from 38.91 to 50.64 t/ha and dry matter yield from 8.92 to 10.17 t/ha at the three diverse locations. Maximum crude protein and crude fibre contents were obtained at NARC, Islamabad and AARI, Faisalabad. Maximum green fodder and dry matter yields were also observed at NARC, Islamabad and AARI, Faisalabad. It was also noted that the same genotypes showed differential response when planted under the diverse environments for green fodder yield, dry matter yield, crude protein and crude fibre contents. Therefore, it was concluded that these differences in forage yield and quality traits under diverse environments were due to differences in soil types, soil fertility, temperature, rain- fall and other climatic conditions. (author)

Quantitative Genetic Analysis for Yield and Yield Components in Boro Rice (Oryza sativa L.

Directory of Open Access Journals (Sweden)

Supriyo CHAKRABORTY

2010-03-01

Full Text Available Twenty-nine genotypes of boro rice (Oryza sativa L. were grown in a randomized block design with three replications in plots of 4m x 1m with a crop geometry of 20 cm x 20 cm between November-April, in Regional Agricultural Research Station, Nagaon, India. Quantitative data were collected on five randomly selected plants of each genotype per replication for yield/plant, and six other yield components, namely plant height, panicles/plant, panicle length, effective grains/panicle, 100 grain weight and harvest index. Mean values of the characters for each genotype were used for analysis of variance and covariance to obtain information on genotypic and phenotypic correlation along with coheritability between two characters. Path analyses were carried out to estimate the direct and indirect effects of boro rice�s yield components. The objective of the study was to identify the characters that mostly influence the yield for increasing boro rice productivity through breeding program. Correlation analysis revealed significant positive genotypic correlation of yield/plant with plant height (0.21, panicles/plant (0.53, panicle length (0.53, effective grains/panicle (0.57 and harvest index (0.86. Path analysis based on genotypic correlation coefficients elucidated high positive direct effect of harvest index (0.8631, panicle length (0.2560 and 100 grain weight (0.1632 on yield/plant with a residual effect of 0.33. Plant height and panicles/plant recorded high positive indirect effect on yield/plant via harvest index whereas effective grains/panicle on yield/plant via harvest index and panicle length. Results of the present study suggested that five component characters, namely harvest index, effective grains/plant, panicle length, panicles/plant and plant height influenced the yield of boro rice. A genotype with higher magnitude of these component characters could be either selected from the existing genotypes or evolved by breeding program for genetic

Genetic analysis of yield and yield components in Oryza sativa x ...

African Journals Online (AJOL)

... inheritance of yield and yield components and to estimate the heritabilities of important quantitative traits in rice (Oryza sativa L.). Six generations viz., P1, P2, F1, F2, BCP1 and BCP2 of a cross between IET6279 and IR70445-146-3-3 were used for the study. Generation mean analysis suggested that additive effects had a ...

Helicity dependence of the {gamma}{yields}p{yields}{yields}n{pi}{sup +}{pi}{sup 0} reaction in the second resonance region

Energy Technology Data Exchange (ETDEWEB)

Ahrens, J.; Altieri, S.; Annand, J.R.M.; Anton, G.; Arends, H.-J.; Aulenbacher, K.; Beck, R.; Bradtke, C.; Braghieri, A.; Degrande, N.; D' Hose, N.; Dutz, H.; Goertz, S.; Grabmayr, P.; Hansen, K.; Harmsen, J.; Harrach, D. von; Hasegawa, S.; Hasegawa, T.; Heid, E.; Helbing, K.; Holvoet, H.; Van Hoorebeke, L.; Horikawa, N.; Iwata, T.; Jahn, O.; Jennewein, P.; Kageya, T.; Kiel, B.; Klein, F.; Kondratiev, R.; Kossert, K.; Krimmer, J.; Lang, M.; Lannoy, B.; Leukel, R.; Lisin, V.; Matsuda, T.; McGeorge, J.C.; Meier, A.; Menze, D.; Meyer, W.; Michel, T.; Naumann, J.; Panzeri, A.; Pedroni, P.; Pinelli, T.; Preobrajenski, I.; Radtke, E.; Reichert, E.; Reicherz, G.; Rohlof, Ch.; Rosner, G.; Rostomyan, T.; Rovelli, C.; Ryckbosch, D.; Sauer, M.; Schoch, B.; Schumacher, M.; Seitz, B.; Speckner, T.; Takabayashi, N.; Tamas, G.; Thomas, A.; Vyver, R. van de; Wakai, A.; Weihofen, W.; Wissmann, F.; Zapadtka, F.; Zeitler, G

2003-01-02

The helicity dependence of the total cross section for the {gamma}{yields}p{yields}{yields}n{pi}{sup +}{pi}{sup 0} reaction has been measured for the first time at incident photon energies from 400 to 800 MeV. The measurement was performed with the large acceptance detector DAPHNE at the tagged photon beam facility of the MAMI accelerator in Mainz. This channel is found to be excited predominantly when the photon and proton have a parallel spin orientation, due to the intermediate production of the D{sub 13} resonance.

Yield surface evolution for columnar ice

Science.gov (United States)

Zhou, Zhiwei; Ma, Wei; Zhang, Shujuan; Mu, Yanhu; Zhao, Shunpin; Li, Guoyu

A series of triaxial compression tests, which has capable of measuring the volumetric strain of the sample, were conducted on columnar ice. A new testing approach of probing the experimental yield surface was performed from a single sample in order to investigate yield and hardening behaviors of the columnar ice under complex stress states. Based on the characteristic of the volumetric strain, a new method of defined the multiaxial yield strengths of the columnar ice is proposed. The experimental yield surface remains elliptical shape in the stress space of effective stress versus mean stress. The effect of temperature, loading rate and loading path in the initial yield surface and deformation properties of the columnar ice were also studied. Subsequent yield surfaces of the columnar ice have been explored by using uniaxial and hydrostatic paths. The evolution of the subsequent yield surface exhibits significant path-dependent characteristics. The multiaxial hardening law of the columnar ice was established experimentally. A phenomenological yield criterion was presented for multiaxial yield and hardening behaviors of the columnar ice. The comparisons between the theoretical and measured results indicate that this current model is capable of giving a reasonable prediction for the multiaxial yield and post-yield properties of the columnar ice subjected to different temperature, loading rate and path conditions.

A note on hypoplastic yielding

OpenAIRE

Nader, José Jorge

2010-01-01

This note discusses briefly the definition of yield surface in hypoplasticity in connection with the physical notion of yielding. The relation of yielding with the vanishing of the material time derivative of the stress tensor and the vanishing of the corotational stress rate is investigated.

Effects of nitrogen application method and weed control on corn yield and yield components.

Science.gov (United States)

Sepahvand, Pariya; Sajedi, Nurali; Mousavi, Seyed Karim; Ghiasvand, Mohsen

2014-04-01

The effects of nitrogen fertilizer application and different methods for weed control on yield and yield components of corn was evaluated in Khorramabad in 2011. The experiment was conducted as a split plot based on randomized complete block design in 3 replications. Nitrogen application was as main plot in 4 levels (no nitrogen, broadcasting nitrogen, banding nitrogen and sprayed nitrogen) and methods of weed control were in 4 levels (non-control weeds, application Equip herbicide, once hand control of weeds and application Equip herbicide+once time weeding) was as subplots. Result illustrated that effects of nitrogen fertilizer application were significant on grain and forage yield, 100 seeds weight, harvest index, grain number per row and cob weight per plant. Grain yield increased by 91.4 and 3.9% in application banding and broadcasting for nitrogen fertilizer, respectively, compared to the no fertilizer treatment. The results show improved efficiency of nitrogen utilization by banding application. Grain yield, harvest index, seed rows per cob, seeds per row and cob weight were increased by weed control. In the application of Equip herbicide+ hand weeding treatment corn grain yield was increased 126% in comparison to weedy control. It represents of the intense affects of weed competition with corn. The highest corn grain yield (6758 kg h(-1)) was related to the application banding of nitrogen fertilizer and Equip herbicide+once hand weeding.

Predicting paddlefish roe yields using an extension of the Beverton–Holt equilibrium yield-per-recruit model

Science.gov (United States)

Colvin, M.E.; Bettoli, Phillip William; Scholten, G.D.

2013-01-01

Equilibrium yield models predict the total biomass removed from an exploited stock; however, traditional yield models must be modified to simulate roe yields because a linear relationship between age (or length) and mature ovary weight does not typically exist. We extended the traditional Beverton-Holt equilibrium yield model to predict roe yields of Paddlefish Polyodon spathula in Kentucky Lake, Tennessee-Kentucky, as a function of varying conditional fishing mortality rates (10-70%), conditional natural mortality rates (cm; 9% and 18%), and four minimum size limits ranging from 864 to 1,016mm eye-to-fork length. These results were then compared to a biomass-based yield assessment. Analysis of roe yields indicated the potential for growth overfishing at lower exploitation rates and smaller minimum length limits than were suggested by the biomass-based assessment. Patterns of biomass and roe yields in relation to exploitation rates were similar regardless of the simulated value of cm, thus indicating that the results were insensitive to changes in cm. Our results also suggested that higher minimum length limits would increase roe yield and reduce the potential for growth overfishing and recruitment overfishing at the simulated cm values. Biomass-based equilibrium yield assessments are commonly used to assess the effects of harvest on other caviar-based fisheries; however, our analysis demonstrates that such assessments likely underestimate the probability and severity of growth overfishing when roe is targeted. Therefore, equilibrium roe yield-per-recruit models should also be considered to guide the management process for caviar-producing fish species.

Path Analysis of Grain Yield and Yield Components and Some Agronomic Traits in Bread Wheat

Directory of Open Access Journals (Sweden)

Mohsen Janmohammadi

2014-01-01

Full Text Available Development of new bread wheat cultivars needs efficient tools to monitor trait association in a breeding program. This investigation was aimed to characterize grain yield components and some agronomic traits related to bread wheat grain yield. The efficiency of a breeding program depends mainly on the direction of the correlation between different traits and the relative importance of each component involved in contributing to grain yield. Correlation and path analysis were carried out in 56 bread wheat genotypes grown under field conditions of Maragheh, Iran. Observations were recorded on 18 wheat traits and correlation coefficient analysis revealed grain yield was positively correlated with stem diameter, spike length, floret number, spikelet number, grain diameter, grain length and 1000 seed weight traits. According to the variance inflation factor (VIF and tolerance as multicollinearity statistics, there are inconsistent relationships among the variables and all traits could be considered as first-order variables (Model I with grain yield as the response variable due to low multicollinearity of all measured traits. In the path coefficient analysis, grain yield represented the dependent variable and the spikelet number and 1000 seed weight traits were the independent ones. Our results indicated that the number of spikelets per spikes and leaf width and 1000 seed weight traits followed by the grain length, grain diameter and grain number per spike were the traits related to higher grain yield. The above mentioned traits along with their indirect causal factors should be considered simultaneously as an effective selection criteria evolving high yielding genotype because of their direct positive contribution to grain yield.

Climatic and technological ceilings for Chinese rice stagnation based on yield gaps and yield trend pattern analysis.

Science.gov (United States)

Zhang, Tianyi; Yang, Xiaoguang; Wang, Hesong; Li, Yong; Ye, Qing

2014-04-01

Climatic or technological ceilings could cause yield stagnation. Thus, identifying the principal reasons for yield stagnation within the context of the local climate and socio-economic conditions are essential for informing regional agricultural policies. In this study, we identified the climatic and technological ceilings for seven rice-production regions in China based on yield gaps and on a yield trend pattern analysis for the period 1980-2010. The results indicate that 54.9% of the counties sampled experienced yield stagnation since the 1980. The potential yield ceilings in northern and eastern China decreased to a greater extent than in other regions due to the accompanying climate effects of increases in temperature and decreases in radiation. This may be associated with yield stagnation and halt occurring in approximately 49.8-57.0% of the sampled counties in these areas. South-western China exhibited a promising scope for yield improvement, showing the greatest yield gap (30.6%), whereas the yields were stagnant in 58.4% of the sampled counties. This finding suggests that efforts to overcome the technological ceiling must be given priority so that the available exploitable yield gap can be achieved. North-eastern China, however, represents a noteworthy exception. In the north-central area of this region, climate change has increased the yield potential ceiling, and this increase has been accompanied by the most rapid increase in actual yield: 1.02 ton ha(-1) per decade. Therefore, north-eastern China shows a great potential for rice production, which is favoured by the current climate conditions and available technology level. Additional environmentally friendly economic incentives might be considered in this region. © 2013 John Wiley & Sons Ltd.

Yield stress of alumina-zirconia suspensions

International Nuclear Information System (INIS)

Ramakrishnan, V.; Pradip; Malghan, S.G.

1996-01-01

The yield stress of concentrated suspensions of alumina, zirconia, and mixed alumina-zirconia powders was measured by the vane technique as a function of solids loading, relative amounts of alumina and zirconia, and pH. At the isoelectric point (IEP), the yield stress varied as the fourth power of the solids loading. The relative ratio of alumina and zirconia particles was important in determining the yield stress of the suspension at the IEP. The yield stress of single and mixed suspensions showed a marked variation with pH. The maximum value occurred at or near the IEP of the suspension. The effect of electrical double-layer forces on the yield stress can be described on the basis of the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. A normalized yield stress--that is, the ratio of the yield stress at a given pH to the yield stress at the IEP predicted by this model--showed good correlation with experimental data

Breeding for Grass Seed Yield

DEFF Research Database (Denmark)

Boelt, Birte; Studer, Bruno

2010-01-01

Seed yield is a trait of major interest for many fodder and amenity grass species and has received increasing attention since seed multiplication is economically relevant for novel grass cultivars to compete in the commercial market. Although seed yield is a complex trait and affected...... by agricultural practices as well as environmental factors, traits related to seed production reveal considerable genetic variation, prerequisite for improvement by direct or indirect selection. This chapter first reports on the biological and physiological basics of the grass reproduction system, then highlights...... important aspects and components affecting the seed yield potential and the agronomic and environmental aspects affecting the utilization and realization of the seed yield potential. Finally, it discusses the potential of plant breeding to sustainably improve total seed yield in fodder and amenity grasses....

Effect of Salinity and Silicon on Seed Yield and Yield Components of Purslane Portulaca oleracea L.(

Directory of Open Access Journals (Sweden)

Z Rahimi

2011-01-01

Full Text Available Abstract In order to study the effects on salinity and silicon application on yield and yield components of purslane (Portulaca oleracea L., an experiment was conducted in a completely randomized desgin with three replications and two factors consisted of four different levels of salinity using NaCl (0, 7, 14, 21dS/m and two levels of silicon (application of one mMol sodium silicate and not application. Increasing salinity concentration significantly caused a negative effect on seed yield. But yield components such as number and weight of seed were more sensitive than number of capsul in main stem in final seed yield. Application of silicon increased seed yield in control but was not significant in salinity levels and leaves and stem biomass. Seed yield and total seed weight in branches was significantly decresed. Weight of 1000 seed in main stem and branches was not significantly different in salinity levels. As a result, purslane could be extremely tolerated to saline conditions, so it seems that it can be cultivated in saline soils and arid regions. Also applied silicon can be increase yield and plant tolerance to environmental stress. Keywords: 1000 seed, Branches, Capsul, Dry weight

Yield stress fluids slowly yield to analysis

NARCIS (Netherlands)

Bonn, D.; Denn, M.M.

2009-01-01

We are surrounded in everyday life by yield stress fluids: materials that behave as solids under small stresses but flow like liquids beyond a critical stress. For example, paint must flow under the brush, but remain fixed in a vertical film despite the force of gravity. Food products (such as

Decomposing global crop yield variability

Science.gov (United States)

Ben-Ari, Tamara; Makowski, David

2014-11-01

Recent food crises have highlighted the need to better understand the between-year variability of agricultural production. Although increasing future production seems necessary, the globalization of commodity markets suggests that the food system would also benefit from enhanced supplies stability through a reduction in the year-to-year variability. Here, we develop an analytical expression decomposing global crop yield interannual variability into three informative components that quantify how evenly are croplands distributed in the world, the proportion of cultivated areas allocated to regions of above or below average variability and the covariation between yields in distinct world regions. This decomposition is used to identify drivers of interannual yield variations for four major crops (i.e., maize, rice, soybean and wheat) over the period 1961-2012. We show that maize production is fairly spread but marked by one prominent region with high levels of crop yield interannual variability (which encompasses the North American corn belt in the USA, and Canada). In contrast, global rice yields have a small variability because, although spatially concentrated, much of the production is located in regions of below-average variability (i.e., South, Eastern and South Eastern Asia). Because of these contrasted land use allocations, an even cultivated land distribution across regions would reduce global maize yield variance, but increase the variance of global yield rice. Intermediate results are obtained for soybean and wheat for which croplands are mainly located in regions with close-to-average variability. At the scale of large world regions, we find that covariances of regional yields have a negligible contribution to global yield variance. The proposed decomposition could be applied at any spatial and time scales, including the yearly time step. By addressing global crop production stability (or lack thereof) our results contribute to the understanding of a key

Effect of nitrogen and water deficit type on the yield gap between the potential and attainable wheat yield

Directory of Open Access Journals (Sweden)

Jiangang Liu

2015-12-01

Full Text Available Water deficit and N fertilizer are the two primary limiting factors for wheat yield in the North China plain, the most important winter wheat (Triticum aestivum L. production area in China. Analyzing the yield gap between the potential yield and the attainable yield can quantify the potential for increasing wheat production and exploring the limiting factors to yield gap in the high-yielding farming region of North China Plain. The Decision Support System for Agrotechnology Transfer (DSSAT model was used to identify methods to increase the grain yield and decrease the gap. In order to explore the impact of N and cultivars on wheat yield in the different drought types, the climate conditions during 1981 to 2011 growing seasons was categorized into low, moderate, and severe water deficit classes according to the anomaly percentage of the water deficit rate during the entire wheat growing season. There are differences (P < 0.0001 in the variations of the potential yields among three cultivars over 30 yr. For all three water deficit types, the more recent cultivars Jimai22 and Shijiazhuang8 had higher yields compared to the older 'Jinan17'. As the N fertilizer rate increased, the yield gap decreased more substantially during the low water deficit years because of the significant increase in attainable yield. Overall, the yield gaps were smaller with less water stress. Replacement of cultivars and appropriate N fertilizer application based on the forecasted drought types can narrow the yield gap effectively.

Synthetic Brassica napus L.: Development and Studies on Morphological Characters, Yield Attributes, and Yield

Directory of Open Access Journals (Sweden)

M. A. Malek

2012-01-01

Full Text Available Brassica napus was synthesized by hybridization between its diploid progenitor species B. rapa and B. oleracea followed by chromosome doubling. Cross with B. rapa as a female parent was only successful. Among three colchicine treatments (0.10, 0.15, and 0.20%, 0.15% gave the highest success (86% of chromosome doubling in the hybrids (AC; 2=19. Synthetic B. napus (AACC, 2=38 was identified with bigger petals, fertile pollens and seed setting. Synthetic B. napus had increased growth over parents and exhibited wider ranges with higher coefficients of variations than parents for morphological and yield contributing characters, and yield per plant. Siliqua length as well as beak length in synthetic B. napus was longer than those of the parents. Number of seeds per siliqua, 1000-seed weight and seed yield per plant in synthetic B. napus were higher than those of the parents. Although flowering time in synthetic B. napus was earlier than both parents, however the days to maturity was little higher over early maturing B. rapa parent. The synthesized B. napus has great potential to produce higher seed yield. Further screening and evaluation is needed for selection of desirable genotypes having improved yield contributing characters and higher seed yield.

Search for B {yields} K{ell}{sup +}{ell}{sup -} and B {yields} K*(892){ell}{sup +}{ell}{sup -}

Energy Technology Data Exchange (ETDEWEB)

Aubert, B.

2004-02-12

The authors present preliminary results from a search for the flavor-changing neutral current decays B {yields} K{ell}{sup +}{ell}{sup -} and B {yields} K*(892){ell}{sup +}{ell}{sup -} using a sample of 22.7 x 10{sup 6} {Upsilon}(4S) {yields} B{bar B} decays collected with the BABAR detector at the PEP-II B Factory. They have reconstructed the following final states: B{sup +} {yields} K{sup +}{ell}{sup +}{ell}{sup -}, B{sup 0} {yields} K{sup 0}{ell}{sup +}{ell}{sup -} (K{sub s}{sup 0} {yields} {pi}{sup +} {pi}{sup -}), B{sup +} {yields} K*{sup +}{ell}{sup +}{ell}{sup -} (K*{sup +} {yields} K{sub s}{sup 0}{pi}{sup +}), and B{sup 0} {yields} K*{sup 0}{ell}{sup +}{ell}{sup -} (K*{sup 0} {yields} K{sup +}{pi}{sup -}), where {ell}{sup +}{ell}{sup -} is either an e{sup +}e{sup -} or {mu}{sup +}{mu}{sup -} pair. They obtain the 90% C.L. upper limits {Beta}(B {yields} K{ell}{sup +}{ell}{sup -}) < 0.6 x 10{sup -6} and {Beta}(B {yields} K*{ell}{sup +}{ell}{sup -}) < 2.5 x 10{sup -6}, close to the Standard Model predictions for these branching fractions.

Effect of Nitrogen and Phosphorus on Yield and Yield Components of Sesame (Sesamumindicum L.)

OpenAIRE

Muhammad Ibrahim; Manzoor Hussain; Ahmad Khan; Yousaf Jamal; Muhammad Ali; Muhammad Faisal Anwar Malik

2014-01-01

Nitrogen is a structural component of chlorophyll and protein therefore adequate supply of nitrogen is beneficial for both carbohydrates and protein metabolism as it promotes cell division and cell enlargement, resulting in more leaf area and thus ensuring good seed and dry matter yield. Theexperiment entitled effect of nitrogen and phosphorus on yield and yield components of sesame were conducted at New Developmental Farm of the University of Agriculture Peshawar during kharif 2013. Randomiz...

Study on Yield and Yield Components of Wheat Genotypes under Different Moisture Regimes

Directory of Open Access Journals (Sweden)

E. Mogtader

2012-10-01

Full Text Available In order to study grain yield and yield components of 16 advanced wheat lines under rainfed and supplementary irrigation conditions, this research was conducted in randomized block design with 3 replications at Maragheh Research Station during 2008-09 seasons. Analysis of variance revealed significant differences for date to heading, plant height, 1000 kernel weight, tiller number, spike length, seed number per spike, spikelet number per spike, peduncle length, harvest index, leaf, sheath length and grain yield. Results also showed that the lines No. 4 (91-142 a 61/3/F35.70/MO73//1D13.1/MLT and 16 (Azar2 with 1895 and 1878 Kg/ha, lines No. 4 and 7 (YUMAI13/5/NAI60/3/14.53/ODIN//CI13441 with 2132 and 2285 Kg/ha had highest grain yield under rainfed and supplementary irrigated conditions respectively. Based on results these 16 lines and cultivars were grouped in 4 and 3 distinct classes using Ward’s Method of cluster analysis under rainfed and irrigated conditions. Path analysis indicated that vigor at shooting stage, seed number per spike and HI were positive important traits to select lines for high yielding potential in this study. HI and TKW had also positive effects on grain under supplementary irrigation.

Plaadid / Margit Tõnson

Index Scriptorium Estoniae

Tõnson, Margit, 1978-

2005-01-01

Uutest heliplaatidest Metro Luminal "Reboot", Rannap, Rein "Tantsib klaveril", Hüpnosaurus "Lint nr 33", Eminem "Encore", Marianne Faithfull "Before the Poision", Aerosmith "You Gotta move", Evanescence "Anywhwre but Home"

Effects of commercial organic fertilizers on the yield and yield structure of potato cultivars

Directory of Open Access Journals (Sweden)

Filipović Vladimir

2012-01-01

Full Text Available The research work has dealt with investigations of two type commercial organic fertilizers (DCM ECO-MIX 4 NPK 7:7:10 i GUANITO NPK 6:15:3 effects on the yield and yield structure of three potato cultivars (Cleopatra, Carrera and Sylvana. The control variant was used in plots without the use of organic fertilizers. The field experiment was performed in 2012. in a populated area Dobrica (N 45° 13’, E 20° 51’, 78 m.s.l. at the experimental farm plot Belča on which is certified organic production, on anthropogenic soil subtype chernozem on carbonate terrace. The results of research showed that the lowest tuber yield was determined in the control treatment (20,87 t ha-1, while the highest yield was achieved with a commercial organic fertilizer DCM ECO-MIX 4 (23,96 t ha-1. Number of tubers per plant corresponded to the characteristics of the studied cultivars. The largest number of tubers per plant was correlated with yield. Specifically, individual variants of the two greatest yields had the highest average number of tubers per plant. Cultivar Cleopatra of variant with GUANITO achieved 17,51 tubers per plant, while cultivar Sylvana of variant with DCM ECO-MIX 4 achieved 17,38 tubers per plant.

Genetic basis of yield and some yield related traits in basmati rice

International Nuclear Information System (INIS)

Saleem, M.Y.; Haq, M.A.; Mirza, J.I.

2010-01-01

Additive, dominance and epistasis components of genetic variation for yield and some yield related traits were assessed through modified triple test cross technique in Basmati rice. Epistasis was found an important part of genetic variation for plant height, tillers per plant, secondary branches per panicle, grains per panicle, 1000-grain weight and yield per plant except primary branches per panicle and panicle length. Bifurcation of epistasis showed that additive x additive (i) type and additive x dominance + dominance x dominance (j + l) types of non-allelic interactions were involved in the expression of these traits. Additive and dominance type of gene action influenced the expression of primary branches per panicle and panicle length. No evidence of directional dominance was observed for these two traits. For plant height, tillers per plant, secondary branches per panicle, grains per panicle, 1000-grain weight and yield per plant, recurrent selection or bi parental mating may be exercised in F2 and following generations however, selection of desired plants may be postponed till F5 or F6 generations to permit maximum obsession of epistatic effects to develop desired cultivar(s) in Basmati rice.(author)

Quantifying potential yield and water-limited yield of summer maize in the North China Plain

Science.gov (United States)

Jiang, Mingnuo; Liu, Chaoshun; Chen, Maosi

2017-09-01

The North China Plain is a major food producing region in China, and climate change could pose a threat to food production in the region. Based on China Meteorological Forcing Dataset, simulating the growth of summer maize in North China Plain from 1979 to 2015 with the regional implementation of crop growth model WOFOST. The results showed that the model can reflect the potential yield and water-limited yield of Summer Maize in North China Plain through the calibration and validation of WOFOST model. After the regional implementation of model, combined with the reanalysis data, the model can better reproduce the regional history of summer maize yield in the North China Plain. The yield gap in Southeastern Beijing, southern Tianjin, southern Hebei province, Northwestern Shandong province is significant, these means the water condition is the main factor to summer maize yield in these regions.

GDP growth and the yield curvature

DEFF Research Database (Denmark)

Møller, Stig Vinther

2014-01-01

This paper examines the forecastability of GDP growth using information from the term structure of yields. In contrast to previous studies, the paper shows that the curvature of the yield curve contributes with much more forecasting power than the slope of yield curve. The yield curvature also...... predicts bond returns, implying a common element to time-variation in expected bond returns and expected GDP growth....

Systematics in delayed neutron yields

Energy Technology Data Exchange (ETDEWEB)

Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan). Atomic Energy Research Inst.

1998-03-01

An attempt was made to reproduce the systematic trend observed in the delayed neutron yields for actinides on the basis of the five-Gaussian representation of the fission yield together with available data sets for delayed neutron emission probability. It was found that systematic decrease in DNY for heavier actinides is mainly due to decrease of fission yields of precursors in the lighter side of the light fragment region. (author)

Fission yield measurements at IGISOL

Science.gov (United States)

Lantz, M.; Al-Adili, A.; Gorelov, D.; Jokinen, A.; Kolhinen, V. S.; Mattera, A.; Moore, I.; Penttilä, H.; Pomp, S.; Prokofiev, A. V.; Rakopoulos, V.; Rinta-Antila, S.; Simutkin, V.; Solders, A.

2016-06-01

The fission product yields are an important characteristic of the fission process. In fundamental physics, knowledge of the yield distributions is needed to better understand the fission process. For nuclear energy applications good knowledge of neutroninduced fission-product yields is important for the safe and efficient operation of nuclear power plants. With the Ion Guide Isotope Separator On-Line (IGISOL) technique, products of nuclear reactions are stopped in a buffer gas and then extracted and separated by mass. Thanks to the high resolving power of the JYFLTRAP Penning trap, at University of Jyväskylä, fission products can be isobarically separated, making it possible to measure relative independent fission yields. In some cases it is even possible to resolve isomeric states from the ground state, permitting measurements of isomeric yield ratios. So far the reactions U(p,f) and Th(p,f) have been studied using the IGISOL-JYFLTRAP facility. Recently, a neutron converter target has been developed utilizing the Be(p,xn) reaction. We here present the IGISOL-technique for fission yield measurements and some of the results from the measurements on proton induced fission. We also present the development of the neutron converter target, the characterization of the neutron field and the first tests with neutron-induced fission.

Fission yield measurements at IGISOL

Directory of Open Access Journals (Sweden)

Lantz M.

2016-01-01

Full Text Available The fission product yields are an important characteristic of the fission process. In fundamental physics, knowledge of the yield distributions is needed to better understand the fission process. For nuclear energy applications good knowledge of neutroninduced fission-product yields is important for the safe and efficient operation of nuclear power plants. With the Ion Guide Isotope Separator On-Line (IGISOL technique, products of nuclear reactions are stopped in a buffer gas and then extracted and separated by mass. Thanks to the high resolving power of the JYFLTRAP Penning trap, at University of Jyväskylä, fission products can be isobarically separated, making it possible to measure relative independent fission yields. In some cases it is even possible to resolve isomeric states from the ground state, permitting measurements of isomeric yield ratios. So far the reactions U(p,f and Th(p,f have been studied using the IGISOL-JYFLTRAP facility. Recently, a neutron converter target has been developed utilizing the Be(p,xn reaction. We here present the IGISOL-technique for fission yield measurements and some of the results from the measurements on proton induced fission. We also present the development of the neutron converter target, the characterization of the neutron field and the first tests with neutron-induced fission.

Effect of different tillage intensity on yields and yield-forming factors in winter wheat

Directory of Open Access Journals (Sweden)

Martin Houšť

2012-01-01

Full Text Available The paper presents results of a study on application of minimum tillage technologies when growing winter wheat. Experiments were performed in the sugar-beet-growing region with loamy chernozem within the period of 2005–2009. Aanalysed and evaluated were effects of different methods of soil processing on yield-forming factors in stands of winter wheat grown after three different preceding crops (i.e. alfalfa, maize for silage and pea. Evaluated were the following four variants of tillage: (1 conventional ploughing to the depth of 0.22 m (Variant 1; (2 ploughing to the depth of 0.15 m (Variant 2; (3 direct sowing into the untilled soil (Variant 3, and (4 shallow tillage to the depth of 0.10 m (Variant 4.The effect of different tillage intensity on winter wheat yields was statistically non-significant after all forecrops. After alfalfa, the highest and the lowest average yields were recorded in Variant 2 (i.e. with ploughing to the depth of 0.15 m and Variant 3 (direct sowing into the untilled soil, respectively. After maize grown for silage, higher yields were obtained in Variant 2 and Variant 1 (conventional ploughing while in Variants 4 and 3 the obtained yields were lower. When growing winter wheat after pea as a preceding crop, the highest and the lowest average yields were recorded after direct sowing (Variant 3 and in Variant 1 (i.e. ploughing to the depth of 0.22 m, respectively. Results of studies on effect of different tillage technologies on yields of winter wheat crops indicate that under the given pedological and climatic conditions it is possible to apply methods of reduced tillage intensity. However, the choice of the corresponding technology must be performed with regard to the type of preceding crop.

Precise measurement of {gamma}(K{yields}e {nu}({gamma}))/{gamma}(K{yields}{mu} {nu}({gamma})) and study of K{yields}e {nu} {gamma}

Energy Technology Data Exchange (ETDEWEB)

Ambrosino, F.; Massarotti, P.; Meola, S.; Napolitano, M. [Dipartimento di Scienze Fisiche dell' Universita ' ' Federico II' ' , Napoli (Italy); INFN Sezione di Napoli, Napoli (Italy); Antonelli, A.; Antonelli, M.; Bencivenni, G.; Bloise, C.; Bossi, F.; Capon, G.; Capussela, T.; Ciambrone, P.; De Lucia, E.; De Simone, P.; Dreucci, M.; Felici, G.; Gatti, C.; Giovannella, S.; Jacewicz, M.; Lanfranchi, G.; Miscetti, S.; Moulson, M.; Murtas, F.; Palutan, M.; Santangelo, P.; Sciascia, B.; Sibidanov, A.; Spadaro, T.; Venanzoni, G. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Archilli, F. [Dipartimento di Fisica dell' Universita ' ' Tor Vergata' ' , Rome (Italy); INFN Sezione di Roma Tor Vergata, Rome (Italy); Beltrame, P.; Denig, A.; Mueller, S. [Johannes Gutenberg-Universitaet, Institut fuer Kernphysik, Mainz (Germany); Bini, C.; De Santis, A.; De Zorzi, G.; Di Domenico, A.; Fiore, S.; Franzini, P.; Gauzzi, P. [Dipartimento di Fisica dell' Universita ' ' La Sapienza' ' , Rome (Italy); INFN Sezione di Roma, Rome (Italy); Bocchetta, S.; Ceradini, F.; Di Micco, B.; Nguyen, F. [Dipartimento di Fisica dell' Universita ' ' Roma Tre' ' , Rome (Italy); INFN Sezione di Roma Tre, Rome (Italy); Branchini, P.; Graziani, E.; Passeri, A.; Tortora, L. [INFN Sezione di Roma Tre, Rome (Italy); Capriotti, D. [Dipartimento di Fisica dell' Universita ' ' Roma Tre' ' , Rome (Italy); Di Donato, C. [INFN Sezione di Napoli, Napoli (Italy); Kulikov, V. [Institute for Theoretical and Experimental Physics, Moscow (Russian Federation); Lee-Franzini, J. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); State University of New York, Physics Department, Stony Brook (United States); Martini, M.; Patera, V.; Versaci, R. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Dipartimento di Energetica dell' Universita ' ' La Sapienza' ' , Rome (Italy); Valente, P. [INFN Sezione di Roma, Rome (Italy)

2009-12-15

We present a precise measurement of the ratio R{sub K}={gamma}(K{yields}e{nu}({gamma}))/{gamma}(K{yields}{mu}{nu}({gamma})) and a study of the radiative process K{yields}e{nu}{gamma}, performed with the KLOE detector. The results are based on data collected at the Frascati e{sup +}e{sup -} collider DA {phi}NE for an integrated luminosity of 2.2 fb{sup -1}. We find R{sub K}=(2.493{+-}0.025{sub stat}{+-}0.019{sub syst}) x 10{sup -5}, in agreement with the Standard Model expectation. This result is used to improve constraints on parameters of the Minimal Supersymmetric Standard Model with lepton flavor violation. We also measured the differential decay rate d {gamma}(K{yields}e{nu}{gamma})/dE{sub {gamma}} for photon energies 10

Geoelectrical parameter-based multivariate regression borehole yield model for predicting aquifer yield in managing groundwater resource sustainability

Directory of Open Access Journals (Sweden)

Kehinde Anthony Mogaji

2016-07-01

Full Text Available This study developed a GIS-based multivariate regression (MVR yield rate prediction model of groundwater resource sustainability in the hard-rock geology terrain of southwestern Nigeria. This model can economically manage the aquifer yield rate potential predictions that are often overlooked in groundwater resources development. The proposed model relates the borehole yield rate inventory of the area to geoelectrically derived parameters. Three sets of borehole yield rate conditioning geoelectrically derived parameters—aquifer unit resistivity (ρ, aquifer unit thickness (D and coefficient of anisotropy (λ—were determined from the acquired and interpreted geophysical data. The extracted borehole yield rate values and the geoelectrically derived parameter values were regressed to develop the MVR relationship model by applying linear regression and GIS techniques. The sensitivity analysis results of the MVR model evaluated at P ⩽ 0.05 for the predictors ρ, D and λ provided values of 2.68 × 10−05, 2 × 10−02 and 2.09 × 10−06, respectively. The accuracy and predictive power tests conducted on the MVR model using the Theil inequality coefficient measurement approach, coupled with the sensitivity analysis results, confirmed the model yield rate estimation and prediction capability. The MVR borehole yield prediction model estimates were processed in a GIS environment to model an aquifer yield potential prediction map of the area. The information on the prediction map can serve as a scientific basis for predicting aquifer yield potential rates relevant in groundwater resources sustainability management. The developed MVR borehole yield rate prediction mode provides a good alternative to other methods used for this purpose.

Nut crop yield records show that budbreak-based chilling requirements may not reflect yield decline chill thresholds

Science.gov (United States)

Pope, Katherine S.; Dose, Volker; Da Silva, David; Brown, Patrick H.; DeJong, Theodore M.

2015-06-01

Warming winters due to climate change may critically affect temperate tree species. Insufficiently cold winters are thought to result in fewer viable flower buds and the subsequent development of fewer fruits or nuts, decreasing the yield of an orchard or fecundity of a species. The best existing approximation for a threshold of sufficient cold accumulation, the "chilling requirement" of a species or variety, has been quantified by manipulating or modeling the conditions that result in dormant bud breaking. However, the physiological processes that affect budbreak are not the same as those that determine yield. This study sought to test whether budbreak-based chilling thresholds can reasonably approximate the thresholds that affect yield, particularly regarding the potential impacts of climate change on temperate tree crop yields. County-wide yield records for almond ( Prunus dulcis), pistachio ( Pistacia vera), and walnut ( Juglans regia) in the Central Valley of California were compared with 50 years of weather records. Bayesian nonparametric function estimation was used to model yield potentials at varying amounts of chill accumulation. In almonds, average yields occurred when chill accumulation was close to the budbreak-based chilling requirement. However, in the other two crops, pistachios and walnuts, the best previous estimate of the budbreak-based chilling requirements was 19-32 % higher than the chilling accumulations associated with average or above average yields. This research indicates that physiological processes beyond requirements for budbreak should be considered when estimating chill accumulation thresholds of yield decline and potential impacts of climate change.

Effect of Supplementary Irrigation on Yield, Yield Components and Protein Percentages of Chickpea Cultivars in Ilam, Iran

Directory of Open Access Journals (Sweden)

A. Maleki

2012-01-01

Full Text Available In order to study the effect of supplementary irrigation on yield, yield components and protein percentages of three cultivars of chickpea an experiment carried out as split plot, based on randomized complete blocks design, with three replications in Ilam, in 2009-2010 growing season. Irrigation treatments were: control, without irrigation (I0, irrigation at the stage of %50 blooming, irrigation at the stage of %50 flowering, irrigation at the stage of pods filling, which were allocated to main plots and genotypes, ILC482, Filip93-93 and local variety to sub plots. Irrigation treatments had significantly effect on seed and biological yields, harvest index, pod numbers per plant, seed numbers per pod and 100 seed weight. The Filip93-93 produced highest (1140.51 kg/ha and the local variety lowest seed yields (1056.98 kg/ha.Irrigation at the stage of pod filling and blooming increased by seed yield %41.3 and %29.3 respectively as  compared to control .Irrigation at the pod filling period produced the highest seed yield. The Filip93-93 produced highest yield (1263.31 kg/ha when the field irrigated at pod filling stage and the local variety at control treatment (without irrigation the lowest seed yield (893.26 kg/ha.

Will energy crop yields meet expectations?

International Nuclear Information System (INIS)

Searle, Stephanie Y.; Malins, Christopher J.

2014-01-01

Expectations are high for energy crops. Government policies in the United States and Europe are increasingly supporting biofuel and heat and power from cellulose, and biomass is touted as a partial solution to energy security and greenhouse gas mitigation. Here, we review the literature for yields of 5 major potential energy crops: Miscanthus spp., Panicum virgatum (switchgrass), Populus spp. (poplar), Salix spp. (willow), and Eucalyptus spp. Very high yields have been achieved for each of these types of energy crops, up to 40 t ha −1  y −1 in small, intensively managed trials. But yields are significantly lower in semi-commercial scale trials, due to biomass losses with drying, harvesting inefficiency under real world conditions, and edge effects in small plots. To avoid competition with food, energy crops should be grown on non-agricultural land, which also lowers yields. While there is potential for yield improvement for each of these crops through further research and breeding programs, for several reasons the rate of yield increase is likely to be slower than historically has been achieved for cereals; these include relatively low investment, long breeding periods, low yield response of perennial grasses to fertilizer, and inapplicability of manipulating the harvest index. Miscanthus × giganteus faces particular challenges as it is a sterile hybrid. Moderate and realistic expectations for the current and future performance of energy crops are vital to understanding the likely cost and the potential of large-scale production. - Highlights: • This review covers Miscanthus, switchgrass, poplar, willow, and Eucalyptus. • High yields of energy crops are typically from small experimental plots. • Field scale yields are lower due to real world harvesting losses and edge effects. • The potential for yield improvement of energy crops is relatively limited. • Expectations must be realistic for successful policies and commercial production

Seed yield components and their potential interaction in grasses - to what extend does seed weigth influence yield?

DEFF Research Database (Denmark)

Boelt, B; Gislum, R

2010-01-01

 In a first-year seed crop of red fescue (Festuca rubra L.) the degree of lodging was controlled by the use of Moddus (Trinexapac-ethyl). Seed weight was found to increase by the decreasing degree of lodging prior to harvest. The higher seed weights were accompanied by higher yields even though...... the number of reproductive tillers and floret site utilization (FSU) were unaffected by the treatments. Seed yield is affected by several yield components and reflects the interaction between the seed yield potential (e.g. number of reproductive tillers, number of spikelets and florets/spikelet per...... reproductive tiller), the utilization of the potential (e.g. seed set, seed weight) and the realization of the seed yield potential, defined as the number of florets forming a saleable seed. The realization of the seed yield potential is affected by seed retention, seed weight and other traits associated...

Effects of internal phosphorus loadings and food-web structure on the recovery of a deep lake from eutrophication

Science.gov (United States)

Lepori, Fabio; Roberts, James J.

2017-01-01

We used monitoring data from Lake Lugano (Switzerland and Italy) to assess key ecosystem responses to three decades of nutrient management (1983–2014). We investigated whether reductions in external phosphorus loadings (Lext) caused declines in lake phosphorus concentrations (P) and phytoplankton biomass (Chl a), as assumed by the predictive models that underpinned the management plan. Additionally, we examined the hypothesis that deep lakes respond quickly to Lext reductions. During the study period, nutrient management reduced Lext by approximately a half. However, the effects of such reduction on P and Chl a were complex. Far from the scenarios predicted by classic nutrient-management approaches, the responses of P and Chl a did not only reflect changes in Lext, but also variation in internal P loadings (Lint) and food-web structure. In turn, Lint varied depending on basin morphometry and climatic effects, whereas food-web structure varied due to apparently stochastic events of colonization and near-extinction of key species. Our results highlight the complexity of the trajectory of deep-lake ecosystems undergoing nutrient management. From an applied standpoint, they also suggest that [i] the recovery of warm monomictic lakes may be slower than expected due to the development of Lint, and that [ii] classic P and Chl a models based on Lext may be useful in nutrient management programs only if their predictions are used as starting points within adaptive frameworks.

Effect of Application of Pseudomonas fluorescent Strains on Yield and Yield Components of Rapeseed Cultivars

Directory of Open Access Journals (Sweden)

R Najafi

2015-09-01

Full Text Available Plant growth promoting rhizobacteria has been identified as an alternative to chemical fertilizer to enhance plant growth and yield directly and indirectly. Use of rhizosphere free living bacteria is one of the methods for crop production and leads to improvement of resources absorption. In order to study of yield, yield components and radiation use efficiency, under application of PGPR condition, an experiment was carried out in 2008 growing season at Agriculture and natural resources research station of Mashhad. The cultivars selected from three rapeseed species belong to Brassica napus, Brassica rapa and Brassica juncea (landrace, BP.18، Goldrush، Parkland، Hyola330، Hyola401. Experimental factorial design was randomized in complete block with three replications. Treatments included six varieties of Rapeseed and inoculations were four levels as non–inoculation, inoculation with P. fluorescens169, P. putida108 and use then together. Results showed that strains of fluorescent pseudomonas bacteria had greatest effects on yield and yield components cultivars. A significant difference in the number of pods per plant and 1000 seed weight observed. The cultivars were different in all treats except 1000 seed weight. Overall results indicated that application of growth stimulating bacteria in combination with different cultivars, had a positive effect growth, yield characteristics of plant varieties of rapeseed plants.

Impact of Inter-Row Spacing on Yield and Yield Components of several Annual Medics Species

Directory of Open Access Journals (Sweden)

Mahnaz BAGHERI

2010-12-01

Full Text Available A field study was conducted in Faculty of Agriculture, Tarbiat Modares University, Tehran, Iran to evaluate the effects of three within-row spacing treatments (20, 30 and 40 cm on forage and seed production of five species of annual medics (Medicago scutellata cv. Sava; M. littoralis cv. Herald; M. polymorpha cv. Santiago; M. minima cv. Orion and M. truncatula cv. Mogul. The experiment was carried out in Faculty of Agriculture, Tarbiat Modares University, Tehran, Iran. The results of the experiment indicated that M. polymorpha had the highest forage yield out of the highest plant population. Latter with average 443.09 Kg ha-1 and M. scutellata with average 409.99 Kg ha-1 produced the highest seed yield. Also, the last species with 1306.78 Kg ha-1 had the highest pod yields. The highest seed yield and pod yield were produced at 20 cm within-row spacing because there were not adequate plants for maximum seed and pod yields in 30 and 40 cm within-row spacing. The tested plant densities did not affect on seeds number per pod, 1000 seeds weight and seeds to burr pod weight ratio. The M. truncatula and M. minima have the highest seeds number per pod. In addition, M. scutellata had the highest 1000 seeds weight with an average of 12.57 g. The highest seeds to burr pod ratio was observed in M. polymorpha. The most pod numbers were obtained in 20 and 30 cm within-row spacing and M. polymorpha while, the least pod numbers was observed in M. scutellata. Plant densities did not affect on pod numbers of the mentioned species. The highest dry forage yield was produced in 20 cm within-row spacing. Among the tested tested species, M. truncatula had the highest forage yield with average 870.07 Kg ha-1. This experiment indicated that there is possibility for seed and forage production of tested annual medics in the mentioned zone with the considering suitable plant densities.

Effect of zinc and plant-population on the yield and yield components of maize (zea mays L.)

International Nuclear Information System (INIS)

Kakar, K.M.; Sadiq, S.A.; Tariq, M.

2005-01-01

A field experiment was conducted during 2001 to study the effect of two levels of zinc (0 and 5 kg Zn ha-J) and three plant-densities (60,000, 80,000 and 100,000 plants ha-J) on the performance of two varieties of maize Azam and Pahari and two hybrids N7989 and Babar, at Malakandher Farm of NWFP Agricultural University, Peshawar. Zinc at the rate of 5 kg ha-J increased the cob yield, grain yield and 1000-grain weight, while increase in plant-density significantly increased the number of grains cob-J, number of cob-plant-J, cob-yield, grain-yield and 1000-grain weight. Results revealed that the highest plant-density of 100,000 plant ha-J decreased the number of cobs plant-J, number of grains cob-J and 1000-grain weight. Maximum number of cobs plant-J (0.87), number of grains cob-J (313), cob yield (4602 kg ha-J), grain yield (4222 kg ha-J) and 1000-grain weight (249 g) were obtained with plant- density of 80,000 plant ha-J. The maximum grain-yield of 4333 kg ha-J was recorded in plots of hybrid variety N7989. (author)

Climate Variability and Sugarcane Yield in Louisiana.

Science.gov (United States)

Greenland, David

2005-11-01

This paper seeks to understand the role that climate variability has on annual yield of sugarcane in Louisiana. Unique features of sugarcane growth in Louisiana and nonclimatic, yield-influencing factors make this goal an interesting and challenging one. Several methods of seeking and establishing the relations between yield and climate variables are employed. First, yield climate relations were investigated at a single research station where crop variety and growing conditions could be held constant and yield relations could be established between a predominant older crop variety and a newer one. Interviews with crop experts and a literature survey were used to identify potential climatic factors that control yield. A statistical analysis was performed using statewide yield data from the American Sugar Cane League from 1963 to 2002 and a climate database. Yield values for later years were adjusted downward to form an adjusted yield dataset. The climate database was principally constructed from daily and monthly values of maximum and minimum temperature and daily and monthly total precipitation for six cooperative weather-reporting stations representative of the area of sugarcane production. The influence of 74 different, though not independent, climate-related variables on sugarcane yield was investigated. The fact that a climate signal exists is demonstrated by comparing mean values of the climate variables corresponding to the upper and lower third of adjusted yield values. Most of these mean-value differences show an intuitively plausible difference between the high- and low-yield years. The difference between means of the climate variables for years corresponding to the upper and lower third of annual yield values for 13 of the variables is statistically significant at or above the 90% level. A correlation matrix was used to identify the variables that had the largest influence on annual yield. Four variables [called here critical climatic variables (CCV

Status of fission product yield data

International Nuclear Information System (INIS)

Cuninghame, J.G.

1978-01-01

The topics covered in this paper are: (a) cumulative yields in thermal neutron fission and in fast fission up to 14 MeV incident neutron energy, (b) dependence of the yields on incident neutron energy and spectrum, (c) independent yields, (d) charge dispersion and distribution, and (e) yields of light particles from ternary fission. The paper reviews information on these subjects for fission of actinides from 232 Th upwards with special emphasis on data published since the 1973 Bologna FPND Panel, compares data sets, and discusses the gaps still to be found in them. (author)

ZNJPrice/Earnings Ratio Model through Dividend Yield and Required Yield Above Expected Inflation

Directory of Open Access Journals (Sweden)

Emil Mihalina

2010-07-01

Full Text Available Price/earnings ratio is the most popular and most widespread evaluation model used to assess relative capital asset value on financial markets. In functional terms, company earnings in the very long term can be described with high significance. Empirically, it is visible from long-term statistics that the demanded (required yield on capital markets has certain regularity. Thus, investors first require a yield above the stable inflation rate and then a dividend yield and a capital increase caused by the growth of earnings that influence the price, with the assumption that the P/E ratio is stable. By combining the Gordon model for current dividend value, the model of market capitalization of earnings (price/earnings ratio and bearing in mind the influence of the general price levels on company earnings, it is possible to adjust the price/earnings ratio by deriving a function of the required yield on capital markets measured by a market index through dividend yield and inflation rate above the stable inflation rate increased by profit growth. The S&P 500 index for example, has in the last 100 years grown by exactly the inflation rate above the stable inflation rate increased by profit growth. The comparison of two series of price/earnings ratios, a modelled one and an average 7-year ratio, shows a notable correlation in the movement of two series of variables, with a three year deviation. Therefore, it could be hypothesized that three years of the expected inflation level, dividend yield and profit growth rate of the market index are discounted in the current market prices. The conclusion is that, at the present time, the relationship between the adjusted average price/earnings ratio and its effect on the market index on one hand and the modelled price/earnings ratio on the other can clearly show the expected dynamics and course in the following period.

Improving the yield from fermentative hydrogen production.

Science.gov (United States)

Kraemer, Jeremy T; Bagley, David M

2007-05-01

Efforts to increase H(2) yields from fermentative H(2) production include heat treatment of the inoculum, dissolved gas removal, and varying the organic loading rate. Although heat treatment kills methanogens and selects for spore-forming bacteria, the available evidence indicates H(2) yields are not maximized compared to bromoethanesulfonate, iodopropane, or perchloric acid pre-treatments and spore-forming acetogens are not killed. Operational controls (low pH, short solids retention time) can replace heat treatment. Gas sparging increases H(2) yields compared to un-sparged reactors, but no relationship exists between the sparging rate and H(2) yield. Lower sparging rates may improve the H(2) yield with less energy input and product dilution. The reasons why sparging improves H(2) yields are unknown, but recent measurements of dissolved H(2) concentrations during sparging suggest the assumption of decreased inhibition of the H(2)-producing enzymes is unlikely. Significant disagreement exists over the effect of organic loading rate (OLR); some studies show relatively higher OLRs improve H(2) yield while others show the opposite. Discovering the reasons for higher H(2) yields during dissolved gas removal and changes in OLR will help improve H(2) yields.

Ethiopian Wheat Yield and Yield Gap Estimation: A Spatial Small Area Integrated Data Approach

Science.gov (United States)

Mann, M.; Warner, J.

2015-12-01

Despite the collection of routine annual agricultural surveys and significant advances in GIS and remote sensing products, little econometric research has been undertaken in predicting developing nation's agricultural yields. In this paper, we explore the determinants of wheat output per hectare in Ethiopia during the 2011-2013 Meher crop seasons aggregated to the woreda administrative area. Using a panel data approach, combining national agricultural field surveys with relevant GIS and remote sensing products, the model explains nearly 40% of the total variation in wheat output per hectare across the country. The model also identifies specific contributors to wheat yields that include farm management techniques (eg. area planted, improved seed, fertilizer, irrigation), weather (eg. rainfall), water availability (vegetation and moisture deficit indexes) and policy intervention. Our findings suggest that woredas produce between 9.8 and 86.5% of their potential wheat output per hectare given their altitude, weather conditions, terrain, and plant health. At the median, Amhara, Oromiya, SNNP, and Tigray produce 48.6, 51.5, 49.7, and 61.3% of their local attainable yields, respectively. This research has a broad range of applications, especially from a public policy perspective: identifying causes of yield fluctuations, remotely evaluating larger agricultural intervention packages, and analyzing relative yield potential. Overall, the combination of field surveys with spatial data can be used to identify management priorities for improving production at a variety of administrative levels.

7 CFR 718.2 - Definitions.

Science.gov (United States)

2010-01-01

... sterile high-sugar corn that follows the standard planting and harvesting practices for corn for the area... purposes, brown lint cotton is considered upland cotton. Wheat means wheat for feed or dual purpose variety...

Assessment of occupational injuries in Tendaho Agricultural ...

African Journals Online (AJOL)

Bernt Lindtjorn

oldest public owned agricultural enterprises mainly producing lint cotton. ... contingency for non-response and correcting for finite ..... workers per year in small and medium scale industrial workers .... An ILO perspective, African news letter on.

Fission yield data evaluation system FYDES

International Nuclear Information System (INIS)

Liu Tingjin

1998-01-01

Taking account of some features of fission yield data, to do the fission yield data evaluation conveniently, a fission yield data evaluation system FYDES has been developed for last two years. Outline of the system, data retrieval and data table standardization, data correction codes, data averaging code, simultaneous evaluation code and data fit programs were introduced

Semileptonic form factors D{yields}{pi},K and B{yields}{pi},K from a fine lattice

Energy Technology Data Exchange (ETDEWEB)

Al-Haydari, A.; Ali Khan, A. [Taiz Univ. (Yemen). Dept. of Physics; Braun, V.M.; Collins, S.; Goeckeler, M.; Schaefer, A. [Regensburg Univ. (Germany). Inst. for Theoretical Physics; Lacagnina, G.N. [INFN, Milan (Italy); Panero, M. [Regensburg Univ. (Germany). Inst. for Theoretical Physics; ETH Zuerich (Switzerland). Inst. for Theoretical Physics; Schierholz, G. [Regensburg Univ. (Germany). Inst. for Theoretical Physics; Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2009-03-15

We extract the form factors relevant for semileptonic decays of D and B mesons from a relativistic computation on a fine lattice in the quenched approximation. The lattice spacing is a=0.04 fm (corresponding to a{sup -1}=4.97 GeV), which allows us to run very close to the physical B meson mass, and to reduce the systematic errors associated with the extrapolation in terms of a heavy quark expansion. For decays of D and D{sub s} mesons, our results for the physical form factors at q{sup 2}=0 are as follows: f{sub +}{sup D{yields}}{sup {pi}}(0)=0.74(6)(4), f{sub +}{sup D{yields}}{sup K}(0)=0.78(5)(4) and f{sub +}{sup D{sub s}{yields}}{sup K}(0)=0.68(4)(3). Similarly, for B and B{sub s} we find: f{sub +}{sup B{yields}}{sup {pi}}(0)=0.27(7)(5), f{sub +}{sup B{yields}}{sup K}(0)=0.32(6)(6) and f{sub +}{sup B{sub s}{yields}}{sup K}(0)=0.23(5)(4). We compare our results with other quenched and unquenched lattice calculations, as well as with lightcone sum rule predictions, finding good agreement. (orig.)

Calculation of the total electron excitation cross section in the Born approximation using Slater wave functions for the Li (2s yields 2p), Li (2s yields 3p), Na (3s yields 4p), Mg (3p yields 4s), Ca (4s yields 4p) and K (4s yields 4p) excitations. M.S. Thesis

Science.gov (United States)

Simsic, P. L.

1974-01-01

Excitation of neutral atoms by inelastic scattering of incident electrons in gaseous nebulae were investigated using Slater Wave functions to describe the initial and final states of the atom. Total cross sections using the Born Approximation are calculated for: Li(2s yields 2p), Na(3s yields 4p), k(4s yields 4p). The intensity of emitted radiation from gaseous nebulae is also calculated, and Maxwell distribution is employed to average the kinetic energy of electrons.

Measurements of beryllium sputtering yields at JET

Science.gov (United States)

Jet-Efda Contributors Stamp, M. F.; Krieger, K.; Brezinsek, S.

2011-08-01

The lifetime of the beryllium first wall in ITER will depend on erosion and redeposition processes. The physical sputtering yields for beryllium (both deuterium on beryllium (Be) and Be on Be) are of crucial importance since they drive the erosion process. Literature values of experimental sputtering yields show an order of magnitude variation so predictive modelling of ITER wall lifetimes has large uncertainty. We have reviewed the old beryllium yield experiments on JET and used current beryllium atomic data to produce revised beryllium sputtering yields. These experimental measurements have been compared with a simple physical sputtering model based on TRIM.SP beryllium yield data. Fair agreement is seen for beryllium yields from a clean beryllium limiter. However the yield on a beryllium divertor tile (with C/Be co-deposits) shows poor agreement at low electron temperatures indicating that the effect of the higher sputtering threshold for beryllium carbide is important.

The Effect of Crop Residue and Different NPK Fertilizer Rates on yield Components and Yield of Wheat

Directory of Open Access Journals (Sweden)

fatemeh khamadi

2017-08-01

Full Text Available Introduction Integrated nutrient management involving crop residue/green manures and chemical fertilizer is potential alternative to provide a balanced supply of nutrients, enhance soil quality and thereby sustain higher productivity. The present experiment was undertaken to evaluate the effect of different crop residue management practices and NPK levels on yield components and yield of wheat. Materials and methods Field experiments were conducted during 2012-2014 at department of agronomy, Chamran University. Experiment was laid out in a randomized block designs in split plot arrangement. With three replications. Crop residues were assigned to main plot consistent CR1: wheat residue; CR2: rape residue; CR3: barley residue; CR4: barley residue + vetch; CR5: wheat straw + mungbean; CR6: vetch residue; CR7: mungbean residue; CR8: No residue incorporation as main plot and three NPK fertilizer rates: F1: (180N-120P-100K kg.ha-1; F2: (140N-90P-80K kg.ha-1; F3: (90N-60P-40K kg.ha-1 as sub plots. Twelve hills were collected at physiological maturity for measuring yield components from surrounding area of grain yield harvest area. Yield components, viz. number of spike per m2, seed per spike, 1000- grain weight, plant height were measured. Grain and straw yields were recorded from the central 5 m2 grain yield harvest area of each treatment and harvest index was calculated. Data were subjected to analysis by SAS and mean companions were performed using the Duncan multiple range test producer. Also, graphs were drawn in Excel software. Results and discussion The result of analysis variance showed significant difference between crop residues for evaluated traits. The result indicated that the highest biological and grain yield was obtained when wheat treated with CR5: wheat straw + mungbean (green manure and CR4: barley straw + vetch (green manure. Biological and grain yield increased 31 and 26% respectively by CR5 comparing with control. The highest

Evaluation of Yield and Yield Components of Some Pinto bean (Phaseolus vulgaris L. Genotypes under Late Season Water Deficit Conditions

Directory of Open Access Journals (Sweden)

somayyeh soheili movahhed

2017-10-01

Full Text Available Introduction Drought or water deficit stress is the most important environmental factor which has severe negative impacts on crop yields, especially when the water stress occurs in the flowering stage. Iran is located in arid and semi-arid areas, therefore, attention to the effects of water deficit stress in different stages of plants growth seems necessary. Bean (Phaseolus vulgaris L. is one of the most important legumes that has a major contribution to human diet and provides an important part of the human protein. According to studies, cultivation areas of legumes in Iran are about 97300 hectares and its total production is about 208350 tons of grain. Bean is a fast-growing plant (Tran and Singh, 2002, thus soil water must be sufficiently available to ensure its desirable growth and yield. The aim of this study was to investigate the effect of drought stress on yield and yield components of some pinto bean (Phaseolus vulgaris L. cultivated in Zanjan province. Materials and methods An experiment was conducted as spilt plot based on randomized complete block design with four replications in Zanjan university research farm. Irrigation levels (control and drought stress and genotypes (Local khomein, Sadri, Ks21193 and Ks21189 were set in the main and subplot, respectively. Water deficit stress was applied during flowering stage (50% of the plants were at anthesis. Sampling was performed to measure yield and yield components at the end of the growth period and final maturity. In this experiment number of pod per Plant, numberof grain per pod, 100 grain weight, grain yield, biological yield and harvest index were measured. Results and Discussion In this experiment it was observed that drought stress, genotype and interact irrigation×genotyps were significantly for all traits except biological yield. Drought stress reduced number of pod perplant, number of grain per pod, 100 grain weight, grain yield, biological yield and Harvest Index. Results

GENETIC ANALYSIS OF YIELD AND YIELD COMPONENTS IN ...

African Journals Online (AJOL)

ACSS

2017-11-16

Nov 16, 2017 ... used different genotypes and the environmental conditions under which their ... and Jinks (1971):. Y = m + aa + βd + a2aa + 2aβad +β2dd … .... /plant, 100-grain weight per plant and Grain yield per plant (g) of six generations in IET6279 X IR70445-146-3-. 3 cross. Traits. Generation. Mean. Standard. Range.

Never Say Dye: The Story of Coloured Cotton

Indian Academy of Sciences (India)

cadmium, cobalt, zinc, chromium, are also skin irritants. Chil- dren are especially ... factors, especially sunlight, soil nutrition, and soil type. Scien- tists at Dharwad .... agricultural produce, its contamination with colour lint may have disastrous ...

Nitrogen rate and plant population effects on yield and yield ...

African Journals Online (AJOL)

STORAGESEVER

2008-12-17

Dec 17, 2008 ... density and nitrogen rate increased plant height, lowest pod height, harvest index and seed yield. ... since some combine harvester heads are unable to pick ..... as effected by population density and plant distribution.

Estimation of heterosis in yield and yield attributing traits in single cross hybrids of maize

Directory of Open Access Journals (Sweden)

Hari Prasad Sharma

2016-12-01

Full Text Available A field experiment was conducted at National Maize Research Program, Rampur, Chitwan, Nepal during winter season from 6th October, 2015 to 5th March 2016 to estimate different heterosis on single cross maize hybrids . Thirteen maize hybrids were tested randomized complete block design with three replications. Hybrid namely RML-98/RL-105 gave the highest standard heterosis (57.5% for grain yield over CP-666 followed by RML-4/NML-2 (32.6%, RML-95/RL-105 (29% and RML-5/RL-105 (20.6%. The hybrid RML-98/RL-105 produced the highest standard heterosis (75.1% for grain yield over Rajkumar followed by RML-4/NML-2(50.2%, RML-95/RL-105(46.6%, RML-5/RL-105 and (35.7%. Mid and better parent heterosis were significantly higher for yield and yield attributes viz. ear length, ear diameter, no of kernel row per ear, no of kernel per row and test weight. The highest positive mid-parent heterosis for grain yield was found in RML-98/RL-105 followed by RML-5/RL-105, RML-95/RL-105, and RML-4/NML-2. For the grain yield the better parent heterosis was the highest in RML-98/RL-105, followed by RML-5/RL-105, RML-95/RL-105, and RML-4/NML-2. These results suggested that maize production can be maximized by cultivating hybrids namely RML-98/RL-105, RML-5/RL-105, RML-95/RL-105, and RML-4/NML-2 .

Effects of low doses of gamma rays on yield, yield components, and other characters of two maize varieties

International Nuclear Information System (INIS)

Yousif, Z. B.; Jabbo, N. F.; Khalaf, M. Z.; Majid, A. H.; Ali, H. J.

1994-01-01

The study was conducted during the fall of 1991 and 1992 at Al-Latyfia Experimental Station to determine the effect of low doses of gamma rays on yield, yield components, and other characters of two maize varieties. Five doses were used in addition to control. A factorial experiment with randomized complete block design in three replications was used in the study. Results revealed that there was significant difference between varieties in plant and ear height in 1992. However, differences between varieties were also significantly affected by most yield component characters. Low doses significantly affected plant height, weight of 500 kernels in 1991, and kernel row number in 1992. Grain yield was affected significantly in 1991 and 1992 by low doses. Results showed that 2.0 krad was the most useful low dose to increase grain yield, whereas there was no significant effect between varieties in grain yield. 7 refs., 6 tabs

Rice yield prediction from yield components and limiting factors

NARCIS (Netherlands)

Casanova, D.; Goudriaan, J.; Catala Former, M.M.; Withagen, J.C.M.

2002-01-01

This article aims to quantify growth at field level in relation to crop status and soil properties in irrigated direct-seeded rice. Forty fields were selected in the Ebro Delta (Spain). Rice growth was monitored and soil properties measured. Yield was related to soil properties by a deductive

Preliminary Evaluation of Yield and Yield Components of Some Khorasanian Sesame Ecotypes (Sesamum indicum L.

Directory of Open Access Journals (Sweden)

A. Nezami

2014-09-01

Full Text Available In most region of Khorasan, sesame ecotypes have been planted for many years, but there is little information about seed yield and yield components of them. Therefore a field experimental was conducted to investigation of yield parameters of 14 sesame ecotypes (MSC1, MSC2, MSC3, MSC4, MSC5, MSC6, MSC7, MSC8, MSC9, MSC10, MSC11, MSC12, MSC13 and MSC14 in randomized complete block design with three replications at experimental station, Collage of Agriculture, Ferdowsi University of Mashhad during 2009. Results showed that there were significant difference (P

Plant growth stage-specific injury and economic injury level for verde plant bug, Creontiades signatus (Hemiptera: Miridae), on cotton: effect of bloom period of infestation.

Science.gov (United States)

Brewer, Michael J; Anderson, Darwin J; Armstrong, J Scott

2013-10-01

Verde plant bugs, Creontiades signatus Distant (Hemiptera: Miridae), were released onto caged cotton, Cossypium hirsutum L., for a 1-wk period to characterize the effects of insect density and bloom period of infestation on cotton injury and yield in 2011 and 2012, Corpus Christi, TX. When plants were infested during early bloom (10-11 nodes above first white flower), a linear decline in fruit retention and boll load and a linear increase in boll injury were detected as verde plant bug infestation levels increased from an average of 0.5 to 4 bugs per plant. Lint and seed yield per plant showed a corresponding decline. Fruit retention, boll load, and yield were not affected on plants infested 1 wk later at peak bloom (8-9 nodes above first white flower), even though boll injury increased as infestation levels increased. Second-year testing verified boll injury but not yield loss, when infestations occurred at peak bloom. Incidence of cotton boll rot, known to be associated with verde plant bug feeding, was low to modest (verde plant bug were important contributors to yield decline, damage potential was greatest during the early bloom period of infestation, and a simple linear response best described the yield response-insect density relationship at early bloom. Confirmation that cotton after peak bloom was less prone to verde plant bug injury and an early bloom-specific economic injury level were key findings that can improve integrated pest management decision-making for dryland cotton, at least under low-rainfall growing conditions.

Quantifying yield gaps in wheat production in Russia

International Nuclear Information System (INIS)

Schierhorn, Florian; Prishchepov, Alexander V; Koch, Friedrich J; Müller, Daniel; Faramarzi, Monireh

2014-01-01

Crop yields must increase substantially to meet the increasing demands for agricultural products. Crop yield increases are particularly important for Russia because low crop yields prevail across Russia’s widespread and fertile land resources. However, reliable data are lacking regarding the spatial distribution of potential yields in Russia, which can be used to determine yield gaps. We used a crop growth model to determine the yield potentials and yield gaps of winter and spring wheat at the provincial level across European Russia. We modeled the annual yield potentials from 1995 to 2006 with optimal nitrogen supplies for both rainfed and irrigated conditions. Overall, the results suggest yield gaps of 1.51–2.10 t ha −1 , or 44–52% of the yield potential under rainfed conditions. Under irrigated conditions, yield gaps of 3.14–3.30 t ha −1 , or 62–63% of the yield potential, were observed. However, recurring droughts cause large fluctuations in yield potentials under rainfed conditions, even when the nitrogen supply is optimal, particularly in the highly fertile black soil areas of southern European Russia. The highest yield gaps (up to 4 t ha −1 ) under irrigated conditions were detected in the steppe areas in southeastern European Russia along the border of Kazakhstan. Improving the nutrient and water supply and using crop breeds that are adapted to the frequent drought conditions are important for reducing yield gaps in European Russia. Our regional assessment helps inform policy and agricultural investors and prioritize research that aims to increase crop production in this important region for global agricultural markets. (letter)

Nitrogen rate and plant population effects on yield and yield ...

African Journals Online (AJOL)

STORAGESEVER

2008-12-17

Gan et al., 2003). Nitrogen increases yield by influencing a variety of agronomic and quality parameters. In general, there was an increase in plant height and dry matter accumulation per plant in soybean (Manral and Saxena, ...

Redefining yield gaps at various spatial scales

Science.gov (United States)

Meng, K.; Fishman, R.; Norstrom, A. V.; Diekert, F. K.; Engstrom, G.; Gars, J.; McCarney, G. R.; Sjostedt, M.

2013-12-01

Recent research has highlighted the prevalence of 'yield gaps' around the world and the importance of closing them for global food security. However, the traditional concept of yield gap -defined as the difference between observed and optimal yield under biophysical conditions - omit relevant socio-economic and ecological constraints and thus offer limited guidance on potential policy interventions. This paper proposes alternative definitions of yield gaps by incorporating rich, high resolution, national and sub-national agricultural datasets. We examine feasible efforts to 'close yield gaps' at various spatial scales and across different socio-economic and ecological domains.

Yield Mapping in Salix; Skoerdekartering av salix

Energy Technology Data Exchange (ETDEWEB)

Anderson, Christoffer; Gilbertsson, Mikael; Rogstrand, Gustav; Thylen, Lars

2004-09-01

The most common species for energy forest production is willow. Willow is able to produce a large amount of biomass in a short period of time. Growing willow has a potential to render a good financial result for the farmer if cultivated on fields with the right conditions and plenty of water. Under the right conditions growing willow can give the farmer a net income of 3,000 SEK (about 430 USD) per hectare and year, which is something that common cereal crops cannot compete with. However, this is not the common case since willow is often grown as a substitute crop on fields where cereal crop yield is low. The aim of this study was to reveal if it is possible to measure yield variability in willow, and if it is possible to describe the reasons for yield variation both within the field but also between different fields. Yield mapping has been used in conventional farming for about a decade. The principles for yield mapping are to continuously measure the yield while registering location by the use of GPS when harvesting the field. The collected data is then used to search for spatial variations within the field, and to try to understand the reasons for this variation. Since there is currently no commercial equipment for yield mapping in willow, a yield mapping system had to be developed within this project. The new system was installed on a Claas Jaguar harvester. The principle for yield mapping on the Claas Jaguar harvester is to measure the distance between the feeding rollers. This distance is correlated to the flow through the harvester. The speed and position of the machine was registered using GPS. Knowing the working width of the harvester this information was used to calculate the yield. All collected data was stored on a PDA computer. Soil samples were also collected from the yield mapped fields. This was to be able to test yield against both physical and chemical soil parameters. The result shows that it is possible to measure spatial variations of yield in

Tudengite hea esinemine Willem C. Vis'i nimelisel harjutuskohtuvõistlusel

Index Scriptorium Estoniae

2013-01-01

XX Willem C. Vis’i nimelise rahvusvahelise kaubandusõiguse harjutuskohtuvõistlusel Viinis saavutas Tartu Ülikooli õigusteaduskonna võistkond (Kristina Promet, Jaana Lints, Edgar-Kaj Velbri ja Sandra-Kristin Noot) 290 ülikooli seast 84. koha

Effect of Different Levels of Sulphur Bentonite on Yield and Yield Components of Canola (Brassica napus L.

Directory of Open Access Journals (Sweden)

B Rahimi

2013-04-01

Full Text Available In order to determine the effect of different levels of sulfur bentonite on yield and yield components of canola a factorial experiment was conducted on the basis of randomized complete block design with three replications in Mashhad in 2009-2010 growing season. Factors included four levels of sulfur bentonite (0, 300, 400 and 500 kg.h-1 and two varieties of canola (Modena and Zarfam. The result showed that the increase in sulfur increased some vegetative traits such as leaf area index and plant height. Using sulfur caused increased pod number, seed weight, in addition of oil and protein content and seed yield. Grain yield increase was due to seed weight and LAI. Two varieties were different to responses the sulfur. While in no sulfur application there was no significant difference in seed yield, in 500 Kg sulfur application yield of Zarfam compared to Modena increased about 29.63. According to the results there are significant differences between cultivars in terms of response to the sulfur fertilizer. Therefore it is necessary to evaluate effect of sulfur application of canola productivity in different climate conditions of Iran.

Effects of Plant Density on Sweet and Baby Corn (Hybrid KSC 403 Yield and Yield Components

Directory of Open Access Journals (Sweden)

H Bavi

2016-07-01

Full Text Available Introduction Sweet corn is the one of the most important types of corn. There is a high amount of sugar in the endosperm of sweet corn than dent corn. Baby corn is the ear of corn that is being harvested in the silking stage before the end of pollination. This crop has an interesting using methods as salad, conserve production and vegetative consumption. Both two sweet and baby corn is obtained from one plant in different growth stages and could be harvested from one corn hybrid. Best yield and quality of baby corn is obtained from sweet corn hybrids, because of high amounts of sugar in the grains and ears. Sweet corn and baby corn could be harvested at early dough stage (with about 30 % of humidity and early silking stage before the pollination is completed, respectively. Plant density is the most important factor in growing corn, especially in sweet and baby corn. Khuzestan province is one of the main regions of corn production in Iran. In Khuzestan, forage and silage corn have the most production among the summer crops. Corn is planted in two planting date in Khuzestan: early spring and early summer. Spring corn planting produces little grain yield due to Simultaneity of silking stage with hot early summer days. Because of little production and little research about sweet and baby corn, this study was performed and designed. Materials and Methods In order to investigate the effects of plant density and harvesting method on sweet corn and baby corn yield, an experiment was performed during 2012-13, in research farm of Ramin Agriculture and Natural Resources University of Khuzestan, located in southwest of Iran. In this experiment, four plant densities (7, 9, 11 and 13 plants.m-2 and two harvesting methods (baby corn and sweet corn were investigated in an RCB statistical design with four replications. The KSC 403 hybrid was used and investigated in the experiment, as a sweet corn hybrid. Statistical analysis was performed using SAS 9.1 through

Genotypic Variation in Yield, Yield Components, Root Morphology and Architecture, in Soybean in Relation to Water and Phosphorus Supply

Science.gov (United States)

He, Jin; Jin, Yi; Du, Yan-Lei; Wang, Tao; Turner, Neil C.; Yang, Ru-Ping; Siddique, Kadambot H. M.; Li, Feng-Min

2017-01-01

Water shortage and low phosphorus (P) availability limit yields in soybean. Roots play important roles in water-limited and P-deficient environment, but the underlying mechanisms are largely unknown. In this study we determined the responses of four soybean [Glycine max (L.) Merr.] genotypes [Huandsedadou (HD), Bailudou (BLD), Jindou 21 (J21), and Zhonghuang 30 (ZH)] to three P levels [applied 0 (P0), 60 (P60), and 120 (P120) mg P kg-1 dry soil to the upper 0.4 m of the soil profile] and two water treatment [well-watered (WW) and water-stressed (WS)] with special reference to root morphology and architecture, we compared yield and its components, root morphology and root architecture to find out which variety and/or what kind of root architecture had high grain yield under P and drought stress. The results showed that water stress and low P, respectively, significantly reduced grain yield by 60 and 40%, daily water use by 66 and 31%, P accumulation by 40 and 80%, and N accumulation by 39 and 65%. The cultivar ZH with the lowest daily water use had the highest grain yield at P60 and P120 under drought. Increased root length was positively associated with N and P accumulation in both the WW and WS treatments, but not with grain yield under water and P deficits. However, in the WS treatment, high adventitious and lateral root densities were associated with high N and P uptake per unit root length which in turn was significantly and positively associated with grain yield. Our results suggest that (1) genetic variation of grain yield, daily water use, P and N accumulation, and root morphology and architecture were observed among the soybean cultivars and ZH had the best yield performance under P and water limited conditions; (2) water has a major influence on nutrient uptake and grain yield, while additional P supply can modestly increase yields under drought in some soybean genotypes; (3) while conserved water use plays an important role in grain yield under drought

Water limits to closing yield gaps

Science.gov (United States)

Davis, Kyle Frankel; Rulli, Maria Cristina; Garrassino, Francesco; Chiarelli, Davide; Seveso, Antonio; D'Odorico, Paolo

2017-01-01

Agricultural intensification is often seen as a suitable approach to meet the growing demand for agricultural products and improve food security. It typically entails the use of fertilizers, new cultivars, irrigation, and other modern technology. In regions of the world affected by seasonal or chronic water scarcity, yield gap closure is strongly dependent on irrigation (blue water). Global yield gap assessments have often ignored whether the water required to close the yield gap is locally available. Here we perform a gridded global analysis (10 km resolution) of the blue water consumption that is needed annually to close the yield gap worldwide and evaluate the associated pressure on renewable freshwater resources. We find that, to close the yield gap, human appropriation of freshwater resources for irrigation would have to increase at least by 146%. Most study countries would experience at least a doubling in blue water requirement, with 71% of the additional blue water being required by only four crops - maize, rice, soybeans, and wheat. Further, in some countries (e.g., Algeria, Morocco, Syria, Tunisia, and Yemen) the total volume of blue water required for yield gap closure would exceed sustainable levels of freshwater consumption (i.e., 40% of total renewable surface and groundwater resources).

Evaluation of Yield and Yield Attributes of Five Sweet Potato ...

African Journals Online (AJOL)

0087, and TIS 2532.OP.1.13) were evaluated for yield and agronomic performance in Imo State University Farm, Owerri. The experiment was laid out in a randomised complete block design with three replications. The planting density was 33,000 ...

Estimation of rice yield affected by drought and relation between rice yield and TVDI

Science.gov (United States)

Hongo, C.; Tamura, E.; Sigit, G.

2016-12-01

Impact of climate change is not only seen on food production but also on food security and sustainable development of society. Adaptation to climate change is a pressing issue throughout the world to reduce the risks along with the plans and strategies for food security and sustainable development. As a key adaptation to the climate change, agricultural insurance is expected to play an important role in stabilizing agricultural production through compensating the losses caused by the climate change. As the adaptation, the Government of Indonesia has launched agricultural insurance program for damage of rice by drought, flood and pest and disease. The Government started a pilot project in 2013 and this year the pilot project has been extended to 22 provinces. Having the above as background, we conducted research on development of new damage assessment method for rice using remote sensing data which could be used for evaluation of damage ratio caused by drought in West Java, Indonesia. For assessment of the damage ratio, estimation of rice yield is a key. As the result of our study, rice yield affected by drought in dry season could be estimated at level of 1 % significance using SPOT 7 data taken in 2015, and the validation result was 0.8t/ha. Then, the decrease ratio in rice yield about each individual paddy field was calculated using data of the estimated result and the average yield of the past 10 years. In addition, TVDI (Temperature Vegetation Dryness Index) which was calculated from Landsat8 data in heading season indicated the dryness in low yield area. The result suggests that rice yield was affected by irrigation water shortage around heading season as a result of the decreased precipitation by El Nino. Through our study, it becomes clear that the utilization of remote sensing data can be promising for assessment of the damage ratio of rice production precisely, quickly and quantitatively, and also it can be incorporated into the insurance procedures.

Effect of Different Tillage Methods and Cover Crop Types on Yield and Yield Components of Wheat

Directory of Open Access Journals (Sweden)

Z Sharefee

2018-05-01

Full Text Available Introduction Conservation agriculture is an appropriate strategy for maintaining and improving agricultural resources which increases crop production and stability and also provides environmental protection. This attitude contributes to the conservation of natural resources (soil, water, and air and is one of the most effective ways to overcome the drought crisis, water management and compensation of soil organic matter in arid and semi-arid regions. The practice of zero-tillage decreases the mineralization of organic matter and contributes to the sequestration of organic carbon in the soil. Higher amounts of organic matter in the soil improve soil structure and root growth, water infiltration and retention, and cation exchange capacity. In addition, zero-tillage reduces soil compaction and crop production costs. Cover crops are cultivated to protect the soil from erosion and elements loss by leaching or runoff and also improve the soil moisture and temperature. Given that South Khorasan farmers still use traditional methods of cultivation of wheat, and cover crops have no place in their farming systems, the aim of this study was to investigate the effect of cover crops types and tillage systems on yield and yield components of wheat in Birjand region. Materials and Methods A split plot field experiment was conducted based on randomized complete block design with three replications at the Research Farm of the University of Birjand over the growing season of 2014-2015. The main factor was the type of tillage (no-till, reduced tillage and conventional tillage and cover crop type (chickling pea (Lathyrus sativus, rocket salad (Eruca sativa, triticale (X Triticosecale witmack, barley (Hordeum vulgaris and control (no cover crop was considered as sub plots. Cover crops were planted on July 2014. Before planting wheat, cover crops were dried through spraying paraquat herbicide using a backpack sprayer at a rate of 3 L ha-1. Then the three tillage

Alumina Yield in the Bayer Process

Science.gov (United States)

Den Hond, R.

The alumina industry has historically been able to reduce alumina production costs, by increasing the liquor alumina yield. To know the potential for further yield increases, the phase diagram of the ternary system Na2O-Al2O -H2O at various temperature levels was analysed. It was found that the maximum theorical precipitation alumina yield is 160 g/l, while that for digestion was calculated to be 675 g/l.

Evaluation of yield and yield components and some agronomic traits of white bean genotypes under Karaj climate

Directory of Open Access Journals (Sweden)

M. Ebrahimi

2016-04-01

Full Text Available In order to study compatibility of 30 white bean genotypes under Karaj climate, an experiment was conducted based on randomized Complete Block Design with four replications. Evaluation and statistical analysis was performed for 18 important traits. Analysis of variance results showed that there are significant differences between varieties for all traits. Results of genotypes means comparison with Duncan’s multiple range test showed that genotype No. 29 was better than others in plant height, yield, and biological yield, seed no. per plant and pod weight traits. Simple correlation coefficients were significant between yield and weight of pod, biological yield, number of seed per plant, number of pod per plant, plant height, width of pod and number of seed per pod. Only pod length was negative correlated with yield between all investigated traits. Cluster analysis with UPGMA method arrangement genotypes into three groups. According to this experiment results we can recommend 29 and 30 genotypes for Karaj condition

Evaluation of the Effect of Crop Rotations on Yield and Yield Components of Bread Wheat (Triticum aestivum L. cv. Darya)

OpenAIRE

H. A. Fallahi; U. Mahmadyarov; H. Sabouri; M. Ezat-Ahmadi4

2013-01-01

Grain yield in wheat is influenced directly and indirectly by other plant characteristics. One of the main goals in wheat breeding programs is increase of grain yield. Considering the role of crop rotation in increasing grain yield, and in order to study the difference between crop rotations for wheat yield and yield components (Darya cultivar), an experiment was conducted with six rotation treatments (wheat-chickpea-wheat, wheat-cotton-wheat, wheat-watermelon-wheat, wheat-wheat-wheat, wheat-...

modelling relationship between rainfall variability and yields

African Journals Online (AJOL)

, S. and ... factors to rice yield. Adebayo and Adebayo (1997) developed double log multiple regression model to predict rice yield in Adamawa State, Nigeria. The general form of .... the second are the crop yield/values for millet and sorghum ...

Sequential Path Analysis for Determination of Relationship Between Yield and Yield Components in Bread Wheat (Triticum aestivum.L.

Directory of Open Access Journals (Sweden)

Mohtasham MOHAMMADI

2014-03-01

Full Text Available An experiment was conducted to evaluate 295 wheat genotypes in Alpha-Lattice design with two replications. The arithmetic mean and standard deviation of grain yield was 2706 and 950 (kg/ha,respectively. The results of correlation coefficients indicated that grain yield had significant and positive association with plant height, spike length, early growth vigor and agronomic score. Whereas there were negative correlation coefficients between grain yield and days to physiological maturity and canopy temperature before and during anthesis. Path analysis indicated agronomic score and plant height had high positive direct effects on grain yield, while canopy temperature before and during anthesis, and days to maturity, wes another trait having negative direct effect on grain yield. The results of sequential path analysis showed the traits that accounted as a criteria variable for high grain yield were agronomic score, plant height, canopy temperature, spike length, chlorophyll content and early growth vigor, which were determined as first, second and third order variables and had strong effects on grain yield via one or more paths. More important, as canopy temperature, agronomic score and early growth vigor can be evaluated quickly and easily, these traits may be used for evaluation of large populations.

The effects of seed coating treatment on yield and yield components ...

African Journals Online (AJOL)

GREGORY

2010-09-13

Sep 13, 2010 ... 2University of Adnan Menderes, Faculty of Agriculture, Department of Agricultural Mechanization, ... Key words: Fuzzy cotton seed, seed coating, yield components. .... gin turnout (%) characteristics are statistically important.

Interaction Between Phosphorus and Zinc on the Biomass Yield and Yield Attributes of the Medicinal Plant Stevia (Stevia rebaudiana)

Science.gov (United States)

Das, Kuntal; Dang, Raman; Shivananda, T. N.; Sur, Pintu

2005-01-01

A greenhouse experiment was conducted at the Indian Institute of Horticultural Research (IIHR), Bangalore to study the interaction effect between phosphorus (P) and zinc (Zn) on the yield and yield attributes of the medicinal plant stevia. The results show that the yield and yield attributes have been found to be significantly affected by different treatments. The total yield in terms of biomass production has been increased significantly with the application of Zn and P in different combinations and methods, being highest (23.34 g fresh biomass) in the treatment where Zn was applied as both soil (10 kg ZnSO4/ha) and foliar spray (0.2% ZnSO4). The results also envisaged that the different yield attributes viz. height, total number of branches, and number of leaves per plant have been found to be varied with treatments, being highest in the treatment where Zn was applied as both soil and foliar spray without the application of P. The results further indicated that the yield and yield attributes of stevia have been found to be decreased in the treatment where Zn was applied as both soil and foliar spray along with P suggesting an antagonistic effect between Zn and P. PMID:15915292

Interaction Between Phosphorus and Zinc on the Biomass Yield and Yield Attributes of the Medicinal Plant Stevia (Stevia rebaudiana

Directory of Open Access Journals (Sweden)

Kuntal Das

2005-01-01

Full Text Available A greenhouse experiment was conducted at the Indian Institute of Horticultural Research (IIHR, Bangalore to study the interaction effect between phosphorus (P and zinc (Zn on the yield and yield attributes of the medicinal plant stevia. The results show that the yield and yield attributes have been found to be significantly affected by different treatments. The total yield in terms of biomass production has been increased significantly with the application of Zn and P in different combinations and methods, being highest (23.34 g fresh biomass in the treatment where Zn was applied as both soil (10 kg ZnSO4/ha and foliar spray (0.2% ZnSO4. The results also envisaged that the different yield attributes viz. height, total number of branches, and number of leaves per plant have been found to be varied with treatments, being highest in the treatment where Zn was applied as both soil and foliar spray without the application of P. The results further indicated that the yield and yield attributes of stevia have been found to be decreased in the treatment where Zn was applied as both soil and foliar spray along with P suggesting an antagonistic effect between Zn and P.

Enhancement of HHG yield

International Nuclear Information System (INIS)

Serrat, C.; Biegert, J.

2011-01-01

A static electric field periodically distributed in space controls and enhances the yield in high harmonic generation. The method is relatively simple to implement and allows tuning from the extreme-ultraviolet to soft X-ray. The radiation yield is selectively enhanced due to symmetry breaking induced by a static electric field on the interaction between the driving laser and the medium. The enhanced spectral region is tuned by varying the periodicity of the static electric field. Simulations predict an increase of more than two orders of magnitude for harmonics in the water window spectral range.

Equity Volatility and Corporate Bond Yields

OpenAIRE

John Y. Campbell; Glen B. Taksler

2002-01-01

This paper explores the effect of equity volatility on corporate bond yields. Panel data for the late 1990s show that idiosyncratic firm-level volatility can explain as much cross-sectional variation in yields as can credit ratings. This finding, together with the upward trend in idiosyncratic equity volatility documented by Campbell, Lettau, Malkiel, and Xu (2001), helps to explain recent increases in corporate bond yields. The definitive version is available at www.blackwell-synergy.com.

Analysis of yield advantage in mixed cropping

NARCIS (Netherlands)

Ranganathan, R.

1993-01-01

It has long been recognized that mixed cropping can give yield advantages over sole cropping, but methods that can identify such yield benefits are still being developed. This thesis presents a method that combines physiological and economic principles in the evaluation of yield advantage.

An evolutionary yield function based on Barlat 2000 yield function for the superconducting niobium sheet

Science.gov (United States)

Darbandi, Payam; Pourboghrat, Farhang

2011-08-01

Superconducting radio frequency (SRF) niobium cavities are widely used in high-energy physics to accelerate particle beams in particle accelerators. The performance of SRF cavities is affected by the microstructure and purity of the niobium sheet, surface quality, geometry, etc. Following optimum strain paths in the forming of these cavities can significantly control these parameters. To select these strain paths, however, information about the mechanical behavior, microstructure, and formability of the niobium sheet is required. In this study the Barlat 2000 yield function has been used as a yield function for high purity niobium. Results from this study showed that, due to intrinsic behavior, it is necessary to evolve the anisotropic coefficients of Barlat's yield function in order to properly model the plastic behavior of the niobium sheet. The accuracy of the newly developed evolutionary yield function was verified by applying it to the modeling of the hydrostatic bulging of the niobium sheet. Also, in a separate attempt crystal plasticity finite element method was use to model the behavior of the polycrystalline niobium sheet with a particular initial texture.

An evolutionary yield function based on Barlat 2000 yield function for the superconducting niobium sheet

International Nuclear Information System (INIS)

Darbandi, Payam; Pourboghrat, Farhang

2011-01-01

Superconducting radio frequency (SRF) niobium cavities are widely used in high-energy physics to accelerate particle beams in particle accelerators. The performance of SRF cavities is affected by the microstructure and purity of the niobium sheet, surface quality, geometry, etc. Following optimum strain paths in the forming of these cavities can significantly control these parameters. To select these strain paths, however, information about the mechanical behavior, microstructure, and formability of the niobium sheet is required. In this study the Barlat 2000 yield function has been used as a yield function for high purity niobium. Results from this study showed that, due to intrinsic behavior, it is necessary to evolve the anisotropic coefficients of Barlat's yield function in order to properly model the plastic behavior of the niobium sheet. The accuracy of the newly developed evolutionary yield function was verified by applying it to the modeling of the hydrostatic bulging of the niobium sheet. Also, in a separate attempt crystal plasticity finite element method was use to model the behavior of the polycrystalline niobium sheet with a particular initial texture.

Correlation Analysis of some Growth, Yield, Yield Components and ...

African Journals Online (AJOL)

three critical growth stages which was imposed by withholding water (at ... November, 5th December, 19th December and 2nd January) laid out in a split ... Simple correlation coefficient ® of different crop parameters and grain yield ... The husk bran and germ are rich sources of ..... heat in 2009/2010 dry season at Fadam a ...

Assessing Sediment Yield and the Effect of Best Management Practices on Sediment Yield Reduction for Tutuila Island, American Samoa

Science.gov (United States)

Leta, O. T.; Dulai, H.; El-Kadi, A. I.

2017-12-01

Upland soil erosion and sedimentation are the main threats for riparian and coastal reef ecosystems in Pacific islands. Here, due to small size of the watersheds and steep slope, the residence time of rainfall runoff and its suspended load is short. Fagaalu bay, located on the island of Tutuila (American Samoa) has been identified as a priority watershed, due to degraded coral reef condition and reduction of stream water quality from heavy anthropogenic activity yielding high nutrients and sediment loads to the receiving water bodies. This study aimed to estimate the sediment yield to the Fagaalu stream and assess the impact of Best Management Practices (BMP) on sediment yield reduction. For this, the Soil and Water Assessment Tool (SWAT) model was applied, calibrated, and validated for both daily streamflow and sediment load simulation. The model also estimated the sediment yield contributions from existing land use types of Fagaalu and identified soil erosion prone areas for introducing BMP scenarios in the watershed. Then, three BMP scenarios, such as stone bund, retention pond, and filter strip were treated on bare (quarry area), agricultural, and shrub land use types. It was found that the bare land with quarry activity yielded the highest annual average sediment yield of 133 ton per hectare (t ha-1) followed by agriculture (26.1 t ha-1) while the lowest sediment yield of 0.2 t ha-1 was estimated for the forested part of the watershed. Additionally, the bare land area (2 ha) contributed approximately 65% (207 ha) of the watershed's sediment yield, which is 4.0 t ha-1. The latter signifies the high impact as well as contribution of anthropogenic activity on sediment yield. The use of different BMP scenarios generally reduced the sediment yield to the coastal reef of Fagaalu watershed. However, treating the quarry activity area with stone bund showed the highest sediment yield reduction as compared to the other two BMP scenarios. This study provides an estimate

Effect of NS-nitragin application on soybean yield and yield components

Directory of Open Access Journals (Sweden)

Marinković Jelena

2010-01-01

Full Text Available Agricultural soils of Serbia are low in soybean symbiotic bacteria and application of bacteriological preparations has been introduced as a regular cultivation practice when growing soybean. A trial was set up on experimental field of Institute of Field and Vegetable Crops from Novi Sad on chernozem soil using a randomized block design with four replicates. Mineral nitrogen fertilizers were used in rates of 0, 30, 60, and 90 kg ha-1 in the experiment. Each of the nitrogen treatments had two variations, with and without inoculation. The effects of inoculation and different nitrogen fertilizer rates on yield and yield components were determined based on the pod number, seed number, 1000 seed mass and protein and oil content in seeds. Significantly higher pod number was observed in inoculated plants with the application of 30 kg N ha-1. Inoculation with NS-Nitragin increased seed number per plant. In treatment with no mineral nitrogen applied and with application of 30 kg N ha-1 and 60 kg N ha-1, 1000 seed mass was statistically higher in inoculated plants than in uninoculated ones. Inoculation produced statistically significant difference in soybean yield only in the treatment with no mineral nitrogen applied. Inoculation and applied mineral nitrogen rates had no significant effect on protein content in soybean grain.

Effect of sowing dates on yield and yield components on mutant-cum-hybrid lines of bread wheat

International Nuclear Information System (INIS)

Sial, M.A.; Arain, M.A.; Dahot, M.U.; Laghari, K.A.; Naqvi, M.H.; Markhand, G.S.; Mangrio, S.M.; Mirbahar, A.A.

2010-01-01

Twenty-one stable wheat mutant lines along with four check varieties viz., Sarsabz, Kiran-95, T.J.83 and Khirman were evaluated under normal and late sowing dates. The observations were recorded on phenological, morphological and meteorological parameters. Higher yield and improvement in various yield components were recorded at normal sowing as compared to late sowing. Six mutant lines showed superiority in yield than check varieties at normal sowings while three mutants produced more yield than check varieties except Sarsabz at late sowings. At normal sowing eleven mutant lines matured earlier than all check varieties including short duration variety T.J-83 whereas two mutant lines were earlier than Sarsabz and Kiran-95 and thirteen than T.J-83 and Khirman. (author)

Exclusive nonleptonic B{yields}VV decays

Energy Technology Data Exchange (ETDEWEB)

Barik, N [Department of Physics, Utkal University, Bhubaneswar-751004 (India); Naimuddin, Sk [Department of Physics, Maharishi College of Natural Law, Bhubaneswar-751007 (India); Dash, P C [Department of Physics, Prananath Autonomous College, Khurda-752057 (India); Kar, Susmita [Department of Physics, North Orissa University, Baripada-757003 (India)

2009-07-01

The exclusive two-body nonleptonic B{yields}VV decays are investigated, within the factorization approximation, in the relativistic independent quark model based on a confining potential in the scalar-vector harmonic form. The branching ratios and the longitudinal polarization fraction (R{sub L}) are calculated yielding the model predictions in agreement with experiment. Our predicted CP-odd fraction (R{sub perpendicular}) for B{yields}D*D{sub (s)}* decays are in general agreement with other model predictions and within the existing experimental limit.

Genetic variability, trait association and path analysis of yield and yield components in mungbean (vigna radiata (L.) wilczek)

International Nuclear Information System (INIS)

Tabasum, A.; Saleem, M.; Aziz, I.

2010-01-01

Genetic variability, heritability along with genetic advance of traits, their association and direct and indirect effects on yield are essential for crop improvement. Ten mungbean genotypes were studied to assess variability and degree to which various plant traits associate with seed yield. Primary and secondary branches, pods per cluster and pod length showed lesser variability while clusters per plant, 100 seed weight and harvest index exhibited intermediate range of variability. Sufficient genetic variability was observed for plant height, pods per plant, total plant weight and seed yield. Moderate to high heritability estimates were found for all traits. Primary and secondary branches per plant, pod length and 100-seed weight exhibited negative and non significant genotypic and phenotypic correlations with seed yield. Plant height showed positive non-significant and significant genotypic and phenotypic correlation. Pods per cluster correlated significantly negative with seed yield. Clusters per plant, pods per plant, total plant weight and harvest index showed positive significant genotypic and phenotypic correlations with seed yield. Positive direct effects were exerted through secondary branches, pods per plant, pod length, 100 seed weight, total plant weight and harvest index while primary branches, plant height, clusters per plant and pods per cluster had negative direct effects. The present findings could be useful for establishing selection criteria for high seed yield in the mungbean breeding. (author)

Effects of plant densities on yield, yield components and some morphological characters of two cultivators of oilseed rape (Brassica napus L.)

DEFF Research Database (Denmark)

Al-Barzinjy, M.; Stölen, O.; Christiansen, Jørgen Lindskrog

2003-01-01

Effects of Plant Densities on Yield, Yield Components and some Morphological Characters of two Cultivators of Oilseed Rape (Brassica napus L.)......Effects of Plant Densities on Yield, Yield Components and some Morphological Characters of two Cultivators of Oilseed Rape (Brassica napus L.)...

Effects of Drought Stress on Canola (Brassica napus L. Genotypes Yield and Yield Components

Directory of Open Access Journals (Sweden)

R Khani

2018-02-01

Full Text Available Introduction Canola (Brassica napus L. genotypes with wide adaptability to environmental conditions could play a major role in Iran’s oilseed crop production. Selection of high performing genotypes is very important for developing canola cultivation. Water stress can reduce crop yield by affecting both source and sink for assimilation. Canola yield depends on genotype and environmental conditions and response of genotypes to environmental factors. Canola genotypes response to stress depends on the developmental stage and the events occurring prior to and during flowering stage. Resistance to water stress is divided to avoidance and tolerance. Some species are tolerable against water stress. In a while, other species respond ending life cycle, falling leaves and other reactions into water stress. Therefore, investigation of canola genotypes response to water stress in phenological growth stages can be valuable in order to determine resistant or tolerant genotypes. Materials and Methods In order to study the effect of drought stress on canola genotypes yield and its components, an experiment was conducted in 2013-2014 as a split plot based on randomized complete block design with three replications at the research farm, Agricultural and Natural Resources Research Center of East-Azarbaijan, Tabriz-Iran. Three levels of drought stress were considered as main plot (No-stress, stress at the flowering and pod setting growth stages and 18 canola genotypes including HW113, RS12, Karaj1, KR18, L73, L72, HW101, L146, L210, L183, SW101, L5, L201, HW118, KR4, Karaj2, Karaj3 and KS7 as subplots. Flood irrigation was scheduled at 50% field capacity, 30 and 30% field capacity for no-stress, stress at the flowering and pod setting growth stages, respectively; i.e. soil moisture capacity was maintained at 30% by irrigating to 100% field capacity when available moisture reached 30% in drought stress treatments. An ANOVA was conducted using the PROC-GLM procedure

Yield and Yield Components of Vetch (Vigna radiata as Affected by the Use of Vermicompost and Phosphate Bio-fertilizer

Directory of Open Access Journals (Sweden)

Mohammad Mehdi Rahimi

2016-06-01

Full Text Available To evaluate the effects different levels of phosphate biofertilizer barvar-2 and vermi compost on yield and yield components of vetch plant (Vigna radiata L.in Yasouj a factorial experiments was performed in completely randomized design in crop year of 2013. Experimental treatments were phosphate biofertilizer barvar-2 at 3 levels (0, 50, 100 gram per hectare and vermicompost at 4 levels (0, 10, 20, 30 ton per hectare. In this study stem height, root length, biological yield, seed yield and harvest index was measured. ANOVA and comparison of means showed that vermicompost significantly increased stem height, economic and biological yields. Results, also, indicated that highest yield and biomass, 4.3 and 18.8 g/plant, observed respectively when 100 g/ha of barvar-2 and 30 t/ha of vermi compost were used. Using both of phosphate biofertilizer barvar-2 and vermicompost was better than their individnal usage. This indicates that combined use of these 2 factors would produce higher yield. It can be concluded that application of 100 g/ha of barvar-2 and 30 t/ha of vermicompost would a proper recommendation.

Effects of Sowing Date and Limited Irrigation on Yield and Yield Components of Five Rainfed Wheat Varieties in Maragheh Region

Directory of Open Access Journals (Sweden)

A. R. Tavakkoli

2013-03-01

Full Text Available In order to investigate the effects of sowing date (SD and single irrigation (SI amounts on yield and yield components of rainfed wheat varieties, a field experiment was conducted as split-split plots arranged in a randomized complete blocks design with three replications during 2002-2004 at main station of Dryland Agricultural Research Institute in Maragheh, Iran. Treatments included three sowing dates (early, normal and late, three levels of single irrigation (rainfed, 50 mm and 100 mm only at planting time and five wheat varieties (three numbered lines, Azar2 and double-cross Shahi. Results revealed that interactions of SD, SI and wheat varieties were significant for grain yield, number of kernels per spike and water productivity (P≤0.01. Single irrigation at normal planting time increased grain yield, straw, biomass, harvest index, and water productivity. Grain yield and water productivity were increased by 131% and 84.8%, respectively. Single irrigation at late planting time was not significant on agronomic traits and produced low water productivity. Regarding the reaction of wheat to planting date and single irrigation, results showed that normal single irrigation can improve yield, yield components and water productivity index. The effectiveness of single irrigation under dryland conditions can be observed in all wheat cultivars. Although this effectiveness on yield and yield components is observable, but it is necessary to select the time of irrigation properly.

Food for thought: pretty good multispecies yield

DEFF Research Database (Denmark)

Rindorf, Anna; Dichmont, C. M.; Levin, P.S.

2017-01-01

good multidimensional yield to accommodate situations where the yield from a stock affects the ecosystem, economic and social benefits, or sustainability. We demonstrate in a European example that PGMY is a practical concept. As PGMY provides a safe operating space for management that adheres...... that broader ecosystem, economic, and social objectives are addressed. We investigate how the principles of a “pretty good yield” range of fishing mortalities assumed to provide >95% of the average yield for a single stock can be expanded to a pretty good multispecies yield (PGMY) space and further to pretty...

Average L-shell fluorescence, Auger, and electron yields

International Nuclear Information System (INIS)

Krause, M.O.

1980-01-01

The dependence of the average L-shell fluorescence and Auger yields on the initial vacancy distribution is shown to be small. By contrast, the average electron yield pertaining to both Auger and Coster-Kronig transitions is shown to display a strong dependence. Numerical examples are given on the basis of Krause's evaluation of subshell radiative and radiationless yields. Average yields are calculated for widely differing vacancy distributions and are intercompared graphically for 40 3 subshell yields in most cases of inner-shell ionization

Yield performance of brassica varieties under rainfed condition

International Nuclear Information System (INIS)

Hassan, M.Z.U.; Wahla, A.J.; Waqar, M.Q.

2014-01-01

A field study was conducted to evaluate crop growth and seed yield performance of Brassica varieties under Rainfed conditions. The varieties, included in the study, were BSA, Zafar-2000, Pakola, Con.1, Con.2, Abaseen, Rainbow, SPS-5, Bard-1, and KJ-119. KJ-119 (2500.0 KG/HA) among Brassica juncea L. varieties and Abaseen (2425.9 kg/ha) among Brassica napusL. Varieties produced with maximum seed yield as compared to rest of varieties. Significantly, minimum seed yield was observed in check variety BSA. The significant difference in seed yield of Brassica varieties, Abaseen and KJ 119, was attributed to improve yield components over other varieties. Maximum pods per plant and seeds per pod led these varieties to attain maximum yield. Inspite of weather variations existence during years 2007-09,the same varieties produced with maximum seed yield. (author)

Status of fission yield data

International Nuclear Information System (INIS)

England, T.R.; Blachot, J.

1988-01-01

In this paper we summarize the current status of the recent US evaluation for 34 fissioning nuclides at one or more neutron incident energies and for spontaneous fission. Currently there are 50 yields sets, and for each we have independent and cumulative yields and uncertainties for approximately 1100 fission products. When finalized the recommended data will become part of Version VI of the US ENDF/B. Other major evaluations in progress that are included in a recently formed IAEA Coordinated Research Program are also summarized. In a second part we review two empirical models in use to estimate independent yields. Comparison of model estimates with measured data is presented, including a comparison with some recent data obtained from Lohengrin (Cf-249 T). 18 refs., 13 figs., 3 tabs

Oxygation enhances growth, gas exchange and salt tolerance of vegetable soybean and cotton in a saline vertisol.

Science.gov (United States)

Bhattarai, Surya P; Midmore, David J

2009-07-01

Impacts of salinity become severe when the soil is deficient in oxygen. Oxygation (using aerated water for subsurface drip irrigation of crop) could minimize the impact of salinity on plants under oxygen-limiting soil environments. Pot experiments were conducted to evaluate the effects of oxygation (12% air volume/volume of water) on vegetable soybean (moderately salt tolerant) and cotton (salt tolerant) in a salinized vertisol at 2, 8, 14, 20 dS/m EC(e). In vegetable soybean, oxygation increased above ground biomass yield and water use efficiency (WUE) by 13% and 22%, respectively, compared with the control. Higher yield with oxygation was accompanied by greater plant height and stem diameter and reduced specific leaf area and leaf Na+ and Cl- concentrations. In cotton, oxygation increased lint yield and WUE by 18% and 16%, respectively, compared with the control, and was accompanied by greater canopy light interception, plant height and stem diameter. Oxygation also led to a greater rate of photosynthesis, higher relative water content in the leaf, reduced crop water stress index and lower leaf water potential. It did not, however, affect leaf Na+ or Cl- concentration. Oxygation invariably increased, whereas salinity reduced the K+ : Na+ ratio in the leaves of both species. Oxygation improved yield and WUE performance of salt tolerant and moderately tolerant crops under saline soil environments, and this may have a significant impact for irrigated agriculture where saline soils pose constraints to crop production.

Comparative study of nitrogen fertilizer use efficiency of cotton grown under conventional and fertigation practices using 15N methodology

International Nuclear Information System (INIS)

Janat, M.; Somi, G.

2002-01-01

Nitrogen fertilization and irrigation methods are the key factors of yield increase. With proper management of these two factors a good production and protection of the environment could be attained at the same time. Field experiments were carried out at Hama (Tezeen's Agricultural Research Station) for four consecutive years 1995=1998. The objectives of this study were: Assessment of nitrogen fertilizer use efficiency (NFUE) under conventional and fertigation practices; Nitrogen requirements of cotton crop grown under fertigation practices: Comparative study of water use efficiency (WUE), and seed cotton yield of cotton crop grown under conventional and drip irrigation. Treatments consisted of five nitrogen rates for the fertigated cotton crop (0, 60, 120, 180 and 240 kg N ha -1 ). While of the surface irrigated cotton treatment only one recommended rate by MAAR was applied (180 kg N ha -1 ). Irrigation methods and N treatments were arranged in RBD. The soil water content and available soil nitrogen were monitored according to the standard procedures. The results revealed that fertigation of cotton under the given circumstances improved water use efficiency, nitrogen use efficiency, seed cotton yield, dry matter production, earliness and in some cases lint properties. Under fertigation practices 35-55% of the irrigation water was saved in comparison with surface irrigated cotton grown under the same condition. The seed cotton yield was increased by more than 50% relatively to the surface irrigated cotton. Furthermore, water use efficiency of the fertigated cotton was increased by almost 90 %. (author)

Application of an automatic yarn dismantler to track changes in cotton fiber properties during full scale processing of cotton into carded yarn

CSIR Research Space (South Africa)

Fassihi, A

2016-08-01

Full Text Available Changes in Upland cotton fiber properties from lint to carded yarn, during full scale processing, were tracked, using a newly developed automatic yarn dismantler for dismantling short staple ring-spun yarns. Opening and cleaning increased fiber neps...

Using Low Resolution Satellite Imagery for Yield Prediction and Yield Anomaly Detection

Directory of Open Access Journals (Sweden)

Oscar Rojas

2013-04-01

Full Text Available Low resolution satellite imagery has been extensively used for crop monitoring and yield forecasting for over 30 years and plays an important role in a growing number of operational systems. The combination of their high temporal frequency with their extended geographical coverage generally associated with low costs per area unit makes these images a convenient choice at both national and regional scales. Several qualitative and quantitative approaches can be clearly distinguished, going from the use of low resolution satellite imagery as the main predictor of final crop yield to complex crop growth models where remote sensing-derived indicators play different roles, depending on the nature of the model and on the availability of data measured on the ground. Vegetation performance anomaly detection with low resolution images continues to be a fundamental component of early warning and drought monitoring systems at the regional scale. For applications at more detailed scales, the limitations created by the mixed nature of low resolution pixels are being progressively reduced by the higher resolution offered by new sensors, while the continuity of existing systems remains crucial for ensuring the availability of long time series as needed by the majority of the yield prediction methods used today.

Effect of Coated Urea Fertilizer on Yield and Yield Components of Sweet Corn (KSC 403 under Deficit Irrigation

Directory of Open Access Journals (Sweden)

N Farid

2017-11-01

Full Text Available This study was carried out to assess the effect of coated urea fertilizer on yield and yield components of sweet corn (KSC 403 under different irrigation regimes, in Ramin Agriculture and Natural Sciences University, Iran by using strip split plot in a randomized complete block design with four replications. Three levels of deficit irrigation (100%, 80 and 60% of calculated water requirement of sweet corn were assigned as vertical factor and six sources of urea fertilizer (without urea, un-coated urea, sulfur-coated urea fertilizer, starch-coated urea, agar-coated urea and chitin-coated urea were assigned to horizontal factor. Effects of deficit water and source of fertilizer were statistically significant on plant height, 1000 kernel weight, ear diameter, and number of rows per ear, ear yield, biological yield and harvest index. Maximum of plant height (153.23 cm, 1000 kernel weight (104.51 g, grain yield (9853.3 kg/ha and biological yield (12471.6 kg/ha were obtained in chitin coated urea fertilizer. Maximum of ear diameter (4.67 cm and number of row per ear (13.22 were achieved in agar coated urea fertilizer and that of harvest index (45.79% was indicated by starch-coated urea. Maximum of length of ear, number of kernels per row and grain yield were 23.65cm, 25.83 and 7142 kg/ha, respectively, and were obtained with the using of chitin-coated urea fertilizer and 100% water requirement. Minimum values of these traits were 13.54 cm, 5.56 and 871 kg/ha, respectively, and were obtained by using of control (no urea application and 60% water requirement. Results showed that biopolymer coated urea is potent to improve some morphological characteristics and increase grain yield of sweet corn.

Effects of sowing dates and different fertilizers on yield, yield components, and oil percentage of castor bean (Ricinus communis L.

Directory of Open Access Journals (Sweden)

parviz rezvani moghadam

2009-06-01

Full Text Available In order to study the effects of sowing dates and different fertilizers on yield, yield components, and oil percentage of castor bean, an experiment was conducted at Experimental station, College of Agriculture, Ferdowsi University of Mashhad, Iran in years 2004-2005. The experimental treatments comprised all combinations of four sowing dates (11 April, 25 April, 8 May and 22 May and three different fertilizers (cow manure (30 tons/ha, compost (30 tons/ha, chemical fertilizers (100 kg/ha N and 250 kg/ha of super phosphate and no fertilizer as control. Different characteristics such as plant height, main inflorescence height, number of inflorescence per plant, number of secondary stems per plant, number of capsules per plant, number of grain per plant, grain weight per plant, 100 seed weight, grain yield, oil percentage and oil yield were recorded. A factorial arrangement based on a randomized complete block design with three replications was used. The results showed by delaying sowing date grain yield, seed oil percentage and oil yield were decreased, but there was no significant differences between 25 April, 8 May and 22 May sowing dates. Harvest index and 100 seed weight did not affect by neither sowing dates nor fertilizer treatments. The highest number of branches per plant, number of fertile inflorescences per plant, number of fertile capsules per plant, number of grain per plant, grain weight per plant and biological yield were obtained at 8 May sowing date on chemical fertilizer. Percentage of seed oil, grain yield and oil yield was higher at the first sowing date (11 April in compost and chemical fertilizer treatments. Keywords: Castor bean, sowing date, fertilizer, grain yield, oil percentage.

Interaction Effects of Planting Date and Weed Competition on Yield and Yield Components of Three white Bean Cultivars in Semirom

Directory of Open Access Journals (Sweden)

A. Yadavi

2012-06-01

Full Text Available Unsuitable planting and weed competition are the most important factors that greatly reduce the yield of bean. In order to study the effect of planting date on yield and yield components of three white bean cultivars in weed infest and weed free condition a factorial experiment with randomized complete block design and three replications was carried out at Semirom in 2009. The treatments were planting date (May10, May 25 and June 9 and white bean cultivars (Shekofa, Pak and Daneshkade and two levels of weed infestation (weedy and weed free. Results showed that planting date, weed competition and cultivars had significant effects on yield and yield components of white bean. The 30-day delay in planting date reduced the number of pods per plant, seeds per pod, 100 seed weight and biological yield of white bean cultivars, 22.5, 18, 20.1 and 22.5 percent respectively. Also weed competition, reduced the number of seeds per pod, 100 seed weight and biological yield respectively by 13.5, 5.7 and 27.1 percent. Result of planting date and weed competition interaction effects indicated that the weed competition decreased grain yield (53% in third planting date more than others and delay in planting date was companion with increasing weed density and dry weight in flowering stage of bean. Also Shekofa cultivar had highest grain yield (3379 kg/ha at the first planting date and weed free condition.

INFLUENCE OF WEATHER CONDITIONS ON GRAIN YIELD, OIL CONTENT AND OIL YIELD OF NEW OS SUNFLOWER HYBRIDS

Directory of Open Access Journals (Sweden)

Anto Mijić

2017-01-01

Full Text Available With the purpose of determining the influence of weather conditions on the yield components of sunflower, the results of three-year field trials are analysed in the paper. In the trials sown in Osijek in 2013, 2014 and 2015, there were 15 sunflower hybrids: two foreign hybrids and 13 hybrid combinations of the Agricultural Institute Osijek. In the period before sowing (January – March, the highest amount of precipitation was in 2013 (213.1 mm, then in 2015 (167.9 mm, and the lowest in 2014 (109.5 mm. In the growing period (April – September, the highest amount of precipitation (487.3 mm was in 2014, 475.7 mm in 2013, and in 2015 it was the lowest (251.6 mm. In 2013, during the growing period, the mean monthly air temperature was 19.1°C, in 2015 19.9°C, and in 2014 18.6°C. Of these years, statistically significant at the P=0.05, the highest value of the analysed traits was recorded in 2013: grain yield of 6.47 t ha-1, oil content 51.69% and oil yield 3.05 t ha-1. Grain yield, oil content and oil yield were lower in 2015, and the lowest in 2014. Matej, a newly recognized sunflower hybrid of the Agricultural Institute Osijek had the highest values of grain and oil yield (6.95 and 3.39 t ha-1, and by its oil content of 53.44%, it was in the third place. For high grain and oil yields of sunflower, in addition to the optimal air temperature, the amount and distribution of precipitation before and also during the growing season are very important.

N-acetylcysteine increased rice yield

OpenAIRE

NOZULAIDI, MOHD; JAHAN, MD SARWAR; KHAIRI, MOHD; KHANDAKER, MOHAMMAD MONERUZZAMAN; NASHRIYAH, MAT; KHANIF, YUSOP MOHD

2015-01-01

N-acetylcysteine (NAC) biosynthesized reduced glutathione (GSH), which maintains redox homeostasis in plants under normal and stressful conditions. To justify the effects of NAC on rice production, we measured yield parameters, chlorophyll (Chl) content, minimum Chl fluorescence (Fo), maximum Chl fluorescence (Fm), quantum yield (Fv/Fm), net photosynthesis rate (Pn), photosynthetically active radiation (PAR), and relative water content (RWC). Four treatments, N1G0 (nitrogen (N) with no NAC), ...

The effects of vermicompost and chemical fertilizers on yield and yield components of marshmallow (Altheae officinalis L.

Directory of Open Access Journals (Sweden)

A.A. Sadeghi

2016-05-01

Full Text Available In order to investigate the effects of vermicompost and chemical fertilizers on growth characteristics, yield and yield components of marshmallow (Altheaeofficinalis L., a field experiment was conducted as factorial layout based on a randomized complete block design with three replications at Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, during growing season of 2012. Experimental treatments were designed based on 3 levels of vermicompost (0, 5 and 10 t ha-1 and 5 levels of nitrogen fertilizer (0, 25, 50, 75 and 100% of 200 kg N ha-1. Results indicated that applied vermicompost had significant effects on increasing leaf area, flower weight per plant and grain yield of marshmallow. Flower weight per plant and grain yield of marshmallow was increased by 2 to 3 times by applying vermicompost at 10 t. ha-1, as compared to control treatment. In addition, nitrogen fertilizer had a significant effect on increasing flower weight per plant and grain, mucilage and oil yields of marshmallow. It seems that applying vermicompost can be suitable strategy in reducing the problems caused by excessive using of chemical fertilizers.

Grain yield and agronomic characteristics of Romanian bread wheat ...

African Journals Online (AJOL)

STORAGESEVER

2008-05-16

May 16, 2008 ... Wheat is adapted to diverse environments, between the ... international collaborative studies many new varieties ... Stability of grain yield and quality characteristics over locations ... grain yield capacity and yield components of twelve .... Analysis of variance for grain yield and yield-related traits over two ...

Effect of Salicylic Acid on Yield, Component Yield and Essential Oil of Black Cumin (Nigella sativa L. under Water Deficit Stress

Directory of Open Access Journals (Sweden)

E. Rezaei Chiyaneh

2014-12-01

Full Text Available Since the production of medicinal plants can be influenced by environmental factors such as water limitation. In other hand salicylic acid as a plant regulator can enhance drought resistance in plants. In order to investigate the effect of different irrigation intervals on yield, yield components and essential oil of black cumin (Nigella sativa L., a field experiment was conducted a farm located in West Azerbaijan province- city Nagadeh, West- Azerbaijan, during growing season of 2011- 2012. The experiment was arranged as split plot based on a randomized complete block design with three replications. Irrigation intervals (6, 12 and 18 days and three levels of salicylic acid concentration (0, 0.5 and 1 mM considered as in main plots and sub-plots, respectively. Results showed that irrigation had significant effects on all characteristics such as Plant height, number of follicule per plant, number of seed per follicule, biological yield, grain yield, essential oil content and essential oil yield with the exception of 1000- seed weight. With increasing irrigation intervals from 6 to 18 days, plant height, number of follicule per plant, number of seed per follicule, biological yield, grain yield, essential oil percentage and essential oil yield were decreased up to 49, 52, 40, 35, 43, 20 and 55 %, respectively. In contrast, yield components and yield were enhanced up to treatments 0.5 mM of salicylic acid. Grain yield and essential oil yield with application of 0.5 mM salicylic acid increased up to 13 and 11 % compared to control, respectively. It seems that due to the limited sources of water in the region irrigation after 12 days and 0.5 mM salicylic acid concentration are suitable for black cumin grain production.

Combining ability and heterosis for yield and yield contributing traits in brassica rapa (l.) ssp. dichotoma (roxb.) hanelt

International Nuclear Information System (INIS)

Nasim, A.; Farhatullah, A.; Khan, N.U.; Afzal, M.; Azam, S.M.

2014-01-01

Combining ability was studied for yield and yield contributing traits in 5 * 5 diallel cross in Brassica rapa (L.) ssp. dichotoma (Roxb.) Hanelt. Primary branches plant-1, pods main raceme-1, pod length, 100-seed weight and seed yield plant-1 were significantly different. Heritability and genetic advance estimates were moderate for primary branches plant-1, pods main raceme-1, 100 seed weight whereas were high for seed yield plant-1. Parental line G-909 for primary branches plant-1, pods main raceme-1 and seed yield plant-1, genotype G-902 for pod length and genotype G-403 for 100-seed weight were the best general combiners. Based on combing ability and heterosis, the F1 hybrids G-909 * G-265 (for primary branches plant-1), G-265 * G- 403, G-1500 * G-909 (for pods main raceme-1), G-403 * G-909 (for pod length), G-265 * G-1500 (for 100-seed weight) and G-1500 * G-902, G-909 * G-902 (for seed yield plant-1) can be utilized in future breeding endeavors. Non-additive genetic control, as predominant mechanism, for all the traits necessitates the use of schemes like bi-parental mating design, diallel selective mating followed by recurrent or reciprocal recurrent selection. (author)

Effect of different intercropping patterns on yield and yield components of dill and fenugreek

Directory of Open Access Journals (Sweden)

Behzad Shokati

2014-12-01

Full Text Available A field experiment was conducted based on randomized complete blocks design (RCBD in three replications during 2011 at the research farm of university of Tabriz, Iran. In this study two medicinal plants, dill (Anethum graveolens L. and fenugreek (Trigonella foenum-graecum intercropped at different additive (1:20, 1:40 and 1:60 and different replacement (1:1, 1:2 and 1:3 series. Results showed that dill plant at additive treatment especially in 1:20 and 1:60 series had maximum plant fresh and dry weights, umbels per plant, 1000 seed weight, seeds per plant, biological yield and harvest index. However, fenugreek plant at replacement treatment especially in 1:3 and 1:2 series had maximum biological yield, pod in main stem, pod in branches, seeds per pod, seed weights and grain yield. Fenugreek as a medicinal, forage and legume crop promote dill grows characters and could be an effective plant in intercropping systems.

NIF total neutron yield diagnostic

International Nuclear Information System (INIS)

Cooper, Gary W.; Ruiz, Carlos L.

2001-01-01

We have designed a total neutron yield diagnostic for the National Ignition Facility (NIF) which is based on the activation of In and Cu samples. The particular approach that we have chosen is one in which we calibrate the entire counting system and which we call the ''F factor'' method. In this method, In and/or Cu samples are exposed to known sources of DD and DT neutrons. The activated samples are then counted with an appropriate system: a high purity Ge detector for In and a NaI coincidence system for Cu. We can then calculate a calibration factor, which relates measured activity to total neutron yield. The advantage of this approach is that specific knowledge of such quantities as cross sections and detector efficiencies is not needed. Unless the actual scattering environment of the NIF can be mocked up in the calibration experiment, the F factor will have to be modified using the results of a numerical simulation of the NIF scattering environment. In this article, the calibration factor methodology will be discussed and experimental results for the calibration factors will be presented. Total NIF neutron yields of 10 9 --10 19 can be measured with this method assuming a 50 cm stand-off distance can be employed for the lower yields

31 CFR 351.10 - What do I need to know about market yields, or market bid yields, to understand redemption value...

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false What do I need to know about market yields, or market bid yields, to understand redemption value calculations in this subpart? 351.10 Section... Provisions § 351.10 What do I need to know about market yields, or market bid yields, to understand...

A Remote Sensing-Derived Corn Yield Assessment Model

Science.gov (United States)

Shrestha, Ranjay Man

Agricultural studies and food security have become critical research topics due to continuous growth in human population and simultaneous shrinkage in agricultural land. In spite of modern technological advancements to improve agricultural productivity, more studies on crop yield assessments and food productivities are still necessary to fulfill the constantly increasing food demands. Besides human activities, natural disasters such as flood and drought, along with rapid climate changes, also inflect an adverse effect on food productivities. Understanding the impact of these disasters on crop yield and making early impact estimations could help planning for any national or international food crisis. Similarly, the United States Department of Agriculture (USDA) Risk Management Agency (RMA) insurance management utilizes appropriately estimated crop yield and damage assessment information to sustain farmers' practice through timely and proper compensations. Through County Agricultural Production Survey (CAPS), the USDA National Agricultural Statistical Service (NASS) uses traditional methods of field interviews and farmer-reported survey data to perform annual crop condition monitoring and production estimations at the regional and state levels. As these manual approaches of yield estimations are highly inefficient and produce very limited samples to represent the entire area, NASS requires supplemental spatial data that provides continuous and timely information on crop production and annual yield. Compared to traditional methods, remote sensing data and products offer wider spatial extent, more accurate location information, higher temporal resolution and data distribution, and lower data cost--thus providing a complementary option for estimation of crop yield information. Remote sensing derived vegetation indices such as Normalized Difference Vegetation Index (NDVI) provide measurable statistics of potential crop growth based on the spectral reflectance and could

Neutron yields from bombardment of α-particles

International Nuclear Information System (INIS)

Nakasima, Ryuzo

1982-09-01

The thick target neutron yields from bombardment of <10 MeV α-particles are calculated based on the reaction cross sections. The results for the elements of Z < 15 are compared with existing calculated or measured neutron yield data. For the elements of 16 < Z < 50, elemental or isotopic neutron yields are calculated if the cross section data are available. (author)

Satellite-based assessment of grassland yields

Science.gov (United States)

Grant, K.; Siegmund, R.; Wagner, M.; Hartmann, S.

2015-04-01

Cutting date and frequency are important parameters determining grassland yields in addition to the effects of weather, soil conditions, plant composition and fertilisation. Because accurate and area-wide data of grassland yields are currently not available, cutting frequency can be used to estimate yields. In this project, a method to detect cutting dates via surface changes in radar images is developed. The combination of this method with a grassland yield model will result in more reliable and regional-wide numbers of grassland yields. For the test-phase of the monitoring project, a study area situated southeast of Munich, Germany, was chosen due to its high density of managed grassland. For determining grassland cutting robust amplitude change detection techniques are used evaluating radar amplitude or backscatter statistics before and after the cutting event. CosmoSkyMed and Sentinel-1A data were analysed. All detected cuts were verified according to in-situ measurements recorded in a GIS database. Although the SAR systems had various acquisition geometries, the amount of detected grassland cut was quite similar. Of 154 tested grassland plots, covering in total 436 ha, 116 and 111 cuts were detected using CosmoSkyMed and Sentinel-1A radar data, respectively. Further improvement of radar data processes as well as additional analyses with higher sample number and wider land surface coverage will follow for optimisation of the method and for validation and generalisation of the results of this feasibility study. The automation of this method will than allow for an area-wide and cost efficient cutting date detection service improving grassland yield models.

Examining the roles that changing harvested areas, closing yield-gaps, and increasing yield ceilings have had on crop production

Science.gov (United States)

Johnston, M.; Ray, D. K.; Mueller, N. D.; Foley, J. A.

2011-12-01

With an increasing and increasingly affluent population, there has been tremendous effort to examine strategies for sustainably increasing agricultural production to meet this surging global demand. Before developing new solutions from scratch, though, we believe it is important to consult our recent agricultural history to see where and how agricultural production changes have already taken place. By utilizing the newly created temporal M3 cropland datasets, we can for the first time examine gridded agricultural yields and area, both spatially and temporally. This research explores the historical drivers of agricultural production changes, from 1965-2005. The results will be presented spatially at the global-level (5-min resolution), as well as at the individual country-level. The primary research components of this study are presented below, including the general methodology utilized in each phase and preliminary results for soybean where available. The complete assessment will cover maize, wheat, rice, soybean, and sugarcane, and will include country-specific analysis for over 200 countries, states, territories and protectorates. Phase 1: The first component of our research isolates changes in agricultural production due to variation in planting decisions (harvested area) from changes in production due to intensification efforts (yield). We examine area/yield changes at the pixel-level over 5-year time-steps to determine how much each component has contributed to overall changes in production. Our results include both spatial patterns of changes in production, as well as spatial maps illustrating to what degree the production change is attributed to area and/or yield. Together, these maps illustrate where, why, and by how much agricultural production has changed over time. Phase 2: In the second phase of our research we attempt to determine the impact that area and yield changes have had on agricultural production at the country-level. We calculate a production

FACTORS INFLUENCING YIELD SPREADS OF THE MALAYSIAN BONDS

Directory of Open Access Journals (Sweden)

Norliza Ahmad

2009-01-01

Full Text Available Malaysian bond market is developing rapidly but not much is understood in terms of macroeconomic factors that could influence the yield spread of the Ringgit Malaysian denominated bonds. Based on a multifactor model, this paper examines the impact of four macroeconomic factors namely: Kuala Lumpur Composite Index (KLCI, Industry Production Index (IPI, Consumer Price Index (CPI and interest rates (IR on bond yield spread of the Malaysian Government Securities (MGS and Corporate Bonds (CBs for a period from January 2001 to December 2008. The findings support the expected hypotheses that CPI and IR are the major drivers that influence the changes in MGS yield spreads. However IPI and KLCI have weak and no influence on MGS yield spreads respectively Whilst IR, CPI and IPI have significant influence on the yield spreads of CB1, CB2 and CB3, KLCI has significant influence only on the CB1 yield spread but not on CB2 and CB3 yield spreads.

Effects of sowing date and plant density on morphological triats, yield and yield components of sweet corn (Zea mays L.

Directory of Open Access Journals (Sweden)

A. Rahmani

2016-04-01

Full Text Available In order to evaluate the effect of sowing date and plant density on the morphological triats, yield and yield components of sweet corn (Zea mays L. var SC. 403 an experiment was conducted at the Khorasan Razavi Agricultural Research and Natural Resources Center, Mashhad, Iran during 2008. This experiment was carried out as split plot based on RCBD with four replications. The sowing date (14th June, 3th July and 24th July and plant densities (66600, 83300 and 111000 plants.ha-1 were arranged in main and sub plots, respectively. The results showed significant differences between different sowing dates for plant height, ear height, and no. of leaves/plant, no. of leaves above ear, stem diameter, dehusked ear yield, can grains yield, no. of grain rows/ear, ear length, ear diameter, kernel depth, no. of ear.plant-1, 1000 kernel weight, ear harvest index and plant harvest index. The highest and the lowest can grains yield with 18.27 and 0.930 ton ha-1 was belonged to 14th June and 24th July sowing date, respectively. Although, delay in sowing date, led to decrease of growth period and also decrease of temperature can lead to improper transfer of photosynthetic materials and cause to grains yield decrease. The plant density had significant effects on husked ear yield, dehusked ear yield and forage yield. The highest can grains yield was harvested from the highest plant density (8.862 t.ha-1 and the lowest can grains yield derived from the lowest plant density (66600 plants.ha-1 with 7.692 t.ha-1. Finally, the interaction of sowing date and plant density was significant only for harvest index. Therefore, the sowing date 14th June and the highest plant density (111000 plants.ha-1, is recommended for summer sowing date of sweet corn in Mashhad with maximum and better can grains production.

Genetic control of late blight, yield and some yield related traits in tomato (lycopersicon esculentum mill.)

International Nuclear Information System (INIS)

Saleem, M.Y.; Asghar, M.; Khan, A.R.; Iqbal, Q.

2011-01-01

Genetic control of late blight (LB) and some economic traits was assessed to identify genotypes suitable for the hybrids were derived from crossing of 2 male sterile lines viz., development of late blight resistant hybrids in tomato. 10 F/sub 1/ hybrid were derived from crossing of 2 male sterile lines viz., TMS1 and TMS2 with 5 elite lines viz., Nagina, Riogrande, Roma, 88572 and Picdenato according to line x tester technique. Disease resistance was measured using detached leaf and whole plant assay techniques. Data were also recorded for days to maturity, number of fruit per plant, single fruit weight and yield per plant. The analysis of variance showed significant differences among crosses, lines, testers and line x tester interaction for almost all parameters. Estimate of genetic components indicated preponderance of additive type of gene action for detached leaf assay, whole plant assay, number of fruit per plant and yield per plant whereas non-additive type of gene action for days to maturity and single fruit weight. Among parents, TMS2, Nagina, Roma and Picdenato showed significant favorable general combing ability (GCA) effects for disease rating traits while TMS1 and Riogrande indicated desirable GCA effects for yield and some yield related traits. Among hybrids, TMS2 x Roma and TMS1 x Riogrande had significant specific combing ability (SCA) effects for detached and whole plant assays. However, hybrid TMS2 x Roma appeared as good combination of LB resistance as it had both parents with desirable GCA effects. All hybrids showed average type of SCA effects for yield and yield components. Genetic control of LB revealed that a multiple crossing program involving genotypes with high GCA effects would be rewarding to identify LB resistant genotypes in early generations. (author)

Biochar boosts tropical but not temperate crop yields

Science.gov (United States)

Jeffery, Simon; Abalos, Diego; Prodana, Marija; Catarina Bastos, Ana; van Groenigen, Jan Willem; Hungate, Bruce A.; Verheijen, Frank

2017-05-01

Applying biochar to soil is thought to have multiple benefits, from helping mitigate climate change [1, 2], to managing waste [3] to conserving soil [4]. Biochar is also widely assumed to boost crop yield [5, 6], but there is controversy regarding the extent and cause of any yield benefit [7]. Here we use a global-scale meta-analysis to show that biochar has, on average, no effect on crop yield in temperate latitudes, yet elicits a 25% average increase in yield in the tropics. In the tropics, biochar increased yield through liming and fertilization, consistent with the low soil pH, low fertility, and low fertilizer inputs typical of arable tropical soils. We also found that, in tropical soils, high-nutrient biochar inputs stimulated yield substantially more than low-nutrient biochar, further supporting the role of nutrient fertilization in the observed yield stimulation. In contrast, arable soils in temperate regions are moderate in pH, higher in fertility, and generally receive higher fertilizer inputs, leaving little room for additional benefits from biochar. Our findings demonstrate that the yield-stimulating effects of biochar are not universal, but may especially benefit agriculture in low-nutrient, acidic soils in the tropics. Biochar management in temperate zones should focus on potential non-yield benefits such as lime and fertilizer cost savings, greenhouse gas emissions control, and other ecosystem services.

Interactive effects of pests increase seed yield.

Science.gov (United States)

Gagic, Vesna; Riggi, Laura Ga; Ekbom, Barbara; Malsher, Gerard; Rusch, Adrien; Bommarco, Riccardo

2016-04-01

Loss in seed yield and therefore decrease in plant fitness due to simultaneous attacks by multiple herbivores is not necessarily additive, as demonstrated in evolutionary studies on wild plants. However, it is not clear how this transfers to crop plants that grow in very different conditions compared to wild plants. Nevertheless, loss in crop seed yield caused by any single pest is most often studied in isolation although crop plants are attacked by many pests that can cause substantial yield losses. This is especially important for crops able to compensate and even overcompensate for the damage. We investigated the interactive impacts on crop yield of four insect pests attacking different plant parts at different times during the cropping season. In 15 oilseed rape fields in Sweden, we estimated the damage caused by seed and stem weevils, pollen beetles, and pod midges. Pest pressure varied drastically among fields with very low correlation among pests, allowing us to explore interactive impacts on yield from attacks by multiple species. The plant damage caused by each pest species individually had, as expected, either no, or a negative impact on seed yield and the strongest negative effect was caused by pollen beetles. However, seed yield increased when plant damage caused by both seed and stem weevils was high, presumably due to the joint plant compensatory reaction to insect attack leading to overcompensation. Hence, attacks by several pests can change the impact on yield of individual pest species. Economic thresholds based on single species, on which pest management decisions currently rely, may therefore result in economically suboptimal choices being made and unnecessary excessive use of insecticides.

Effects of mulch practices on fresh ear yield and yield components of sweet corn

OpenAIRE

KARA, Burhan; ATAR, Bekir

2013-01-01

The experiment was carried out in the vegetation seasons of 2010 and 2011. The main purpose of the study was to determine the effects of mulch practices (a control-unmulched treatment, a plastic mulch treatment, and a straw mulch treatment) on fresh ear yield and some yield-related traits of sweet corn according to 3 sowing dates: 1 April, 15 April, and 1 May, respectively. The main effects of sowing dates were significant for the harvest period, the emerging rate from soil, the fresh ear yie...

Atomistic simulations of the yielding of gold nanowires

International Nuclear Information System (INIS)

Diao Jiankuai; Gall, Ken; Dunn, Martin L.; Zimmerman, Jonathan A.

2006-01-01

We performed atomistic simulations to study the effect of free surfaces on the yielding of gold nanowires. Tensile surface stresses on the surfaces of the nanowires cause them to contract along the length with respect to the bulk face-centered cubic lattice and induce compressive stress in the interior. When the cross-sectional area of a nanowire is less than 2.45 nm x 2.45 nm, the wire yields under its surface stresses. Under external forces and surface stresses, nanowires yield via the nucleation and propagation of the {1 1 1} partial dislocations. The magnitudes of the tensile and compressive yield stress of nanowires increase and decrease, respectively, with a decrease of the wire width. The magnitude of the tensile yield stress is much larger than that of the compressive yield stress for small nanowires, while for small nanowires, tensile and compressive yield stresses have similar magnitudes. The critical resolved shear stress (RSS) by external forces depends on wire width, orientation and loading condition (tension vs. compression). However, the critical RSS in the interior of the nanowires, which is exerted by both the external force and the surface-stress-induced compressive stress, does not change significantly with wire width for same orientation and same loading condition, and can thus serve as a 'local' criterion. This local criterion is invoked to explain the observed size dependence of yield behavior and tensile/compressive yield stress asymmetry, considering surface stress effects and different slip systems active in tensile and compressive yielding

Wheat yield dynamics: a structural econometric analysis.

Science.gov (United States)

Sahin, Afsin; Akdi, Yilmaz; Arslan, Fahrettin

2007-10-15

In this study we initially have tried to explore the wheat situation in Turkey, which has a small-open economy and in the member countries of European Union (EU). We have observed that increasing the wheat yield is fundamental to obtain comparative advantage among countries by depressing domestic prices. Also the changing structure of supporting schemes in Turkey makes it necessary to increase its wheat yield level. For this purpose, we have used available data to determine the dynamics of wheat yield by Ordinary Least Square Regression methods. In order to find out whether there is a linear relationship among these series we have checked each series whether they are integrated at the same order or not. Consequently, we have pointed out that fertilizer usage and precipitation level are substantial inputs for producing high wheat yield. Furthermore, in respect for our model, fertilizer usage affects wheat yield more than precipitation level.

Biogas and Methane Yield from Rye Grass

Directory of Open Access Journals (Sweden)

Tomáš Vítěz

2015-01-01

Full Text Available Biogas production in the Czech Republic has expanded substantially, including marginal regions for maize cultivation. Therefore, there are increasingly sought materials that could partially replace maize silage, as a basic feedstock, while secure both biogas production and its quality.Two samples of rye grass (Lolium multiflorum var. westerwoldicum silage with different solids content 21% and 15% were measured for biogas and methane yield. Rye grass silage with solid content of 15% reached an average specific biogas yield 0.431 m3·kg−1 of organic dry matter and an average specific methane yield 0.249 m3·kg−1 of organic dry matter. Rye grass silage with solid content 21% reached an average specific biogas yield 0.654 m3·kg−1 of organic dry matter and an average specific methane yield 0.399 m3·kg−1 of organic dry matter.

Invited review: A commentary on predictive cheese yield formulas.

Science.gov (United States)

Emmons, D B; Modler, H W

2010-12-01

Predictive cheese yield formulas have evolved from one based only on casein and fat in 1895. Refinements have included moisture and salt in cheese and whey solids as separate factors, paracasein instead of casein, and exclusion of whey solids from moisture associated with cheese protein. The General, Barbano, and Van Slyke formulas were tested critically using yield and composition of milk, whey, and cheese from 22 vats of Cheddar cheese. The General formula is based on the sum of cheese components: fat, protein, moisture, salt, whey solids free of fat and protein, as well as milk salts associated with paracasein. The testing yielded unexpected revelations. It was startling that the sum of components in cheese was SofC) in cheese. The apparent low estimation of SofC led to the idea of adjusting upwards, for each vat, the 5 measured components in the formula by the observed SofC, as a fraction. The mean of the adjusted predicted yields as percentages of actual yields was 99.99%. The adjusted forms of the General, Barbano, and Van Slyke formulas gave predicted yields equal to the actual yields. It was apparent that unadjusted yield formulas did not accurately predict yield; however, unadjusted PY%AY can be useful as a control tool for analyses of cheese and milk. It was unexpected that total milk protein in the adjusted General formula gave the same predicted yields as casein and paracasein, indicating that casein or paracasein may not always be necessary for successful yield prediction. The use of constants for recovery of fat and protein in the adjusted General formula gave adjusted predicted yields equal to actual yields, indicating that analyses of cheese for protein and fat may not always be necessary for yield prediction. Composition of cheese was estimated using a predictive formula; actual yield was needed for estimation of composition. Adjusted formulas are recommended for estimating target yields and cheese yield efficiency. Constants for solute exclusion

Heterosis and combining ability for grain yield and yield component ...

African Journals Online (AJOL)

... ranged from 0 to -13% indicating that the hybrids tend to be earlier in maturity than the parents. The mean squares due to GCA for days to maturity, ear diameter, member of kernels per row, 1000 kernel weight and grain yield were significant, indicating the importance of additive genetic variance in controlling these traits.

Accelerated yield learning in agressive lithography

Science.gov (United States)

Monahan, Kevin M.; Ashkenaz, Scott M.; Chen, Xing; Lord, Patrick J.; Merrill, Mark A.; Quattrini, Rich; Wiley, James N.

2000-06-01

As exposure wavelengths decrease from 248 nm to 193, 157, and even 13 nm (EUV), small process defects can cause collapse of the lithographic process window near the limits of resolution, particularly for the gate and contact structures in high- performance devices. Such sensitivity poses a challenge for lithography process module control. In this work, we show that yield loss can be caused by a combination of macro, micro, CD, and overlay defects. A defect is defined as any yield- affecting process variation. Each defect, regardless of cause, is assumed to have a specific 'kill potential.' The accuracy of the lithographic yield model can be improved by identifying those defects with the highest kill potential or, more importantly, those that pose the highest economic risk. Such economic considerations have led us to develop a simple heuristic model for understanding sampling strategies in defect metrology and for linking metrology capability to yield and profitability.

Benefits of seasonal forecasts of crop yields

Science.gov (United States)

Sakurai, G.; Okada, M.; Nishimori, M.; Yokozawa, M.

2017-12-01

Major factors behind recent fluctuations in food prices include increased biofuel production and oil price fluctuations. In addition, several extreme climate events that reduced worldwide food production coincided with upward spikes in food prices. The stabilization of crop yields is one of the most important tasks to stabilize food prices and thereby enhance food security. Recent development of technologies related to crop modeling and seasonal weather forecasting has made it possible to forecast future crop yields for maize and soybean. However, the effective use of these technologies remains limited. Here we present the potential benefits of seasonal crop-yield forecasts on a global scale for choice of planting day. For this purpose, we used a model (PRYSBI-2) that can well replicate past crop yields both for maize and soybean. This model system uses a Bayesian statistical approach to estimate the parameters of a basic process-based model of crop growth. The spatial variability of model parameters was considered by estimating the posterior distribution of the parameters from historical yield data by using the Markov-chain Monte Carlo (MCMC) method with a resolution of 1.125° × 1.125°. The posterior distributions of model parameters were estimated for each spatial grid with 30 000 MCMC steps of 10 chains each. By using this model and the estimated parameter distributions, we were able to estimate not only crop yield but also levels of associated uncertainty. We found that the global average crop yield increased about 30% as the result of the optimal selection of planting day and that the seasonal forecast of crop yield had a large benefit in and near the eastern part of Brazil and India for maize and the northern area of China for soybean. In these countries, the effects of El Niño and Indian Ocean dipole are large. The results highlight the importance of developing a system to forecast global crop yields.

Genotype x environment interaction and stability analysis for yield ...

African Journals Online (AJOL)

etc

2015-05-06

. Combined analysis of variance (ANOVA) for yield and yield components revealed highly significant .... yield stability among varieties, multi-location trials with ... Mean grain yield (kg/ha) of 17 Kabuli-type chickpea genotypes ...

Botanical trash mixtures analyzed with near-infrared and attenuated total reflectance fourier transform spectroscopy and thermogravimetric analysis

Science.gov (United States)

Botanical cotton trash mixed with lint reduces cotton’s marketability and appearance. During cotton harvesting, ginning, and processing, trash size reduction occurs, thus complicating its removal and identification. This trash causes problems by increasing ends down in yarn formation and thus proce...

7 CFR 1427.101 - Eligible upland cotton.

Science.gov (United States)

2010-01-01

... classification purposes that have been rebaled; (3) Semi-processed motes that are of a quality suitable, without further processing, for spinning, papermaking, or production of non-woven fabric; or (4) Re-ginned... derivatives of the lint cleaning process; or (3) Textile mill wastes. ...

Eesti keele huvi tõi ungari tudengid Tartusse / Sander Liivak

Index Scriptorium Estoniae

Liivak, Sander

2003-01-01

Tartu Ülikoolil on üliõpilasvahetussuhted Budapestis asuva Lorind Eötvösi ülikooliga. Tartus viibivad Edina Csüllög, Bálint Kirpithegyi ja Zoltin Ság 11. aprilli "Õpetajate Lehes" tutvustati Edinat, seekord lähemalt noormeestest

Evaluation of Alternative Peel Ply Surface Preparation Methods of SC-15 Epoxy / Fiberglass Composite Surfaces for Secondary Bonding

Science.gov (United States)

2014-01-01

prepared composite surfaces. Examination of the surface compositions will show differences in makeup and identify any transfer of contaminants...by carefully brushing the specimen with a lint-free cloth followed by a high-pressure nitrogen gas stream. 3.2 X-ray Photospectroscopy (XPS

Deficit Irrigation Effects on Yield, Yield Components and Seed Production of Three Cultivas of Watermelon (Citrullus lanatus (Thunb Matsum and Nakai

Directory of Open Access Journals (Sweden)

P. Jafari

2015-09-01

Full Text Available A two-year study (2005 - 2006 was carried out to explore the effect of deficit irrigation treatments according to evaporation from a class A basin, including ET= 1 (T1, ET = 0.75 (T2, and ET = 0.5 (T3, on yield, yield components and seed yield of three varieties of watermelon (Charleston Gray, Sugar Baby and Crimson Suite in the Varamin Agricultural Research Center of Iran. A randomized complete block design with a split plot arrangement with four replications was used. The results showed that fruit yield, yield components and seed yield were not significantly different in T1 and T2 treatments in contrary to T3 treatment. Among the yield components, number of fruits per plant most suffered from the negative impact of severe water stress (T3 (1.20 fruit per plant. Rind thickness, percent soluble solids in fruit and seed yield were not affected by water stress. According to phenotypic traits, and correlation coefficients, a significant positive correlation (1% probability level was observed between the weighted average, and the number of fruit with the fruit yield. Crimson Suite cultivar produced the highest yield (2533 kg ha-1 compared to the cultivars Charleston Gray and Sugar Baby. Sugar Baby and Crimson Suite cultivars, with 311.7 and 298.2 kg ha-1, respectively, produced the highest amount of seed. Crimson Suite cultiavr had the highest percentage of soluble solids in fruit (1.35. Rind thickness in Crimson Suites, Charleston Gray and Sugar Baby cultivars were 1.35, 1.13 and 1.10 cm, respectively. The results of this study showed that under a moderate moisture stress condition (ET = 0.75, fruit and seed yield could be similar to the no-water stress conditions.

ENDF/B-5. Fission Product Yields File

International Nuclear Information System (INIS)

Schwerer, O.

1985-10-01

The ENDF/B-5 Fission Product Yields File contains a complete set of independent and cumulative fission product yields, representing the final data from ENDF/B-5 as received at the IAEA Nuclear Data Section in June 1985. Yields for 11 fissioning nuclides at one or more neutron incident energies are included. The data are available costfree on magnetic tape from the IAEA Nuclear Data Section. (author). 4 refs

Yield stress determination of a physical gel

DEFF Research Database (Denmark)

Hvidt, Søren

2013-01-01

Pluronic F127 solutions form gels in water with high elastic moduli. Pluronic gels can, however, only withstand small deformations and stresses. Different steady shear and oscillatory methods traditionally used to determine yield stress values are compared. The results show that the yield stresses...... values of these gels depend on test type and measurement time, and no absolute yield stress value can be determined for these physical gels....

Independent isomer yield ratio of 90Rb

International Nuclear Information System (INIS)

Reeder, P.L.; Warner, R.A.; Ford, G.P.; Willmes, H.

1985-05-01

The independent isomer yield ratio for 90 Rb from thermal neutron fission of 235 U has been measured by use of a new technique involving a pulsed reactor and an on-line mass spectrometer facility. The apparent isomer yield ratio was measured for different ion collection time intervals and extrapolated to zero collection time to eliminate interference from 90 Kr decay. The observed isomer yield ratio of 8.7 +- 1.0 is one of the largest ratios measured for a low energy fission process. However, a statistical model analysis shows that the average angular momentum ( = 4.5) deduced from this isomer yield ratio is consistent with average angular momentum for other products from low energy fission. 7 refs

The Effects of Different Nitrogen Sources on Yield and Yield Components of Sweet Corn (Zea mays L. saccharata

Directory of Open Access Journals (Sweden)

ali mojab ghasroddashti

2017-09-01

Full Text Available Introduction Sweet corn (Zea mays L. saccharata is one of the tropical cereals of graminae which is cultivated in order to use for ear. Nitrogen is one of the most important nutrients and key factors to achieve desirable yield. Fertilizers play a major role in crop productivity. However, nowadays, excessive use of fertilizers have been found to have a negative impact on yield and environment. Introducing new management methods based on nitrogen and water use efficiency showed some improvements in the quality and quantity of crop production in association with the health of the community. In fact, soil organic matter content should be maintained in the appropriate level to improve fertility. Using municipal solid waste compost and poultry manure are appropriate solutions. They can increase soil organic matter, modify physicochemical properties and improve crop production. Moreover, they are able to solve problems caused by the accumulation of municipal solid waste compost and poultry manure. Material and Methods In order to investigate the impact of different sources of nitrogen on yield and yield components of sweet corn, a field experiment was conducted as a randomized complete block design with three replications in Marvdasht in 2013. Treatments included different resources of fertilizer: 200 kg.ha-1 net nitrogen (T1, 300 kg.ha-1 net nitrogen (T2, 8 ton.ha-1 poultry manure (T3, 24 ton.ha-1 municipal solid waste compost (T4, 150 kg net nitrogen + 2 ton municipal solid waste compost (T5, 100 kg net nitrogen + 4 ton poultry manure (T6, 150 kg net nitrogen + 6 ton municipal solid waste compost (T7, 100 kg.ha-1 net nitrogen + 12 ton municipal solid waste compost (T8 and fertilizer free (control (T9. At the time of crop maturity, two square meters from middle of each plot were harvested to measure yield and yield components. Statistical analysis was performed using the SAS statistical software. Least significant difference (LSD test at the five

Effect of Limited Irrigation on Yield and Yield Component of Several Sweet Corn (Zea mays L.var Saccharata Varieties

Directory of Open Access Journals (Sweden)

Sh Ghazian Tafrishi

2013-08-01

Full Text Available A randomized complete block design with four replications and a split plot arrangement was conducted in 2010, in order to study the effect of limited irrigation on yield and yield component of sweet corn. Water levels were (100%, 80%, and 60% replacement of plant water requirement which served as main plots. Subplot was a factorial arrangement of three different sweet corn varieties (Merit, Obsession and KSC403 with two planting methods (raised bed and furrow planting. The evaluated traits were ear length, ear diameter, kernels number per row, seed rows per ear, kernel depth, seed thousands weight, kernel yield, shoot biomass, harvest index and Anthesis- silking interval. Results show that limited irrigation significantly decreased all measured characteristics but harvest index. Effect of varieties was significant on evaluated traits too. Kernel weight and seed depth were significantly affected by interaction between variety and planting method. The highest yield was found for 100% replacement of water requirement irrigation level whit 15.2 tones per hectare kernel weight and the lowest belongs to 60% replacement of water requirement by 8.6 tones per hectare kernel weight. Merit and KSC 403 produces the highest (15.9 ton/ha and lowest (8.8 ton/ha seed yield, respectively. Harvest index of different varieties were not affected by irrigation regime. Results show that, in whole, limited irrigation, decreased seed yield in all varieties by affecting diverse yield component.

Simulating the potential yield and yield gaps of sugar beet due to water and nitrogen limitations in Khorasan province using SUCROS model

Directory of Open Access Journals (Sweden)

R Deihimfard

2015-12-01

Full Text Available Introduction Crop productivity is highly constrained by water and nitrogen limitations in many areas of the world (Kalra et al., 2007. Therefore, there is a need to investigate more on nitrogen and water management to achieve higher production as well as quality. Irrigated sugar beet in the cropping systems of Khorasan province in northeastern of Iran accounts for about 34% of the land area under sugar beet production (~115,000 ha with an average yield of around 36 t.ha-1 (Anonymous, 2009. However, there is a huge yield gap (the difference between potential and water and nitrogen-limited yield mainly due to biotic and abiotic factors causing major reduction in farmers’ yield. Accordingly, yield gap analysis should be carried out to reduce the yield reduction and reach the farmer’s yield to the potential yield. The current study aimed to simulate potential yield as well as yield gap related to water and nitrogen shortage in the major sugar beet-growing areas of Khorasan province of Iran. Materials and methods This study was carried out in 6 locations across Khorasan province, which is located in the northeast of Iran. Long term weather data for 1986 to 2009 were obtained from Iran Meteorological Organization for 6 selected locations. The weather data included daily sunshine hours (h, daily maximum and minimum temperatures (◦C, and daily rainfall (mm. Daily solar radiation was estimated using the Goudriaan (1993 method. The validated SUCROSBEET model (Deihimfard, 2011; Deihimfard et al., 2011 was then used to estimate potential, water and nitrogen-limited yield and yield gap of sugar beet for 6 selected locations across the Khorasan province in the northeast of Iran. This model simulates the impacts of weather, genotype and management factors on crop growth and development, soil water and nitrogen balance on a daily basis and finally it predicts crop yield. The model requires input data, including local weather and soil conditions, cultivar

Effect of Foliar Application of Iron, Zinc and Manganese Micronutrients on Yield and Yield Components and Seed Oil of Pot Marigold Calendula officinalis L.

Directory of Open Access Journals (Sweden)

E. Rezaei Chiyaneh

2016-02-01

Full Text Available Although micronutrients effect on growth and yield of different plants has been intensively investigated, but there is limited information on its effect on grain yield and seed oil content of pot marigold Calendula officinalis L.. In order to investigate the effects of micronutrients (Fe, Zn and Mn spraying on yield and yield components and seed oil of pot marigold, a field experiment was conducted based on randomized complete block design with three replications at the Research Farm of Payame Noor University of Nagadeh in 2010. Treatments included Fe, Zn, Mn, mixed solutions of these elements (Fe+Zn, Fe+Mn, Zn+Mn, Fe+Zn+Mn and control (water. Treatments were applied in 2 g/litter twice at stem elongation and early flowering stages. Different traits such as plant height, number of capitol per plant, number seed per capitol, thousand seed weight, biological yield, seed yield, seed oil percentage and oil Yield were recorded. The results showed that foliar application of micronutrients had significant effects on all of these traits. Yield components, seed yield, oil percentage and yield were enhanced by foliar application, compared with control (untreated plants. The maximum number seed per capitol, thousand seed weight and biological yield were relevant to Fe treatment. The highest numbers of capitol per plant and seed yield (643.33 kg.ha-1 were relevant to Zn+Fe treatment and the maximum oil yield (124.20 kg.ha-1 was produced by Zn+ Fe+ Mn treatment. Seed yield and oil yield increased by 31.27% and 44.18% yields more than control, respectively. It can be concluded that, foliar application of micronutrients had positive effects to obtain high yield and oil of pot marigold.

Yield and competition in barley variety mixtures

Directory of Open Access Journals (Sweden)

Kari Jokinen

1991-09-01

Full Text Available Competition between spring barley varieties and yield performance of two-, three and four-variety mixtures were studied in two replacement series field experiments. In the first experiment, repeated in three successive years (1983 —85 the components were the six-row varieties Agneta, Arra, Hja-673 and Porno. In the second experiment (1984, including two nitrogen doses (50 and 100 kgN/ha, both six-row (Agneta, Pomo and two-row (Ida, Kustaa varieties were used. Arra in the first and Agneta in the second experiment were the most competitive varieties. The results suggested that the fast growth of Arra at the beginning promoted its competitive ability. Increase in available nitrogen usually strengthened the competitiveness of Agneta. The observed competitive differences between varieties were not related to the earliness of a variety, neither to the morphological characters (two- and six-row varieties nor to the grain yield of a variety grown alone. The competitive ability was not always a stable character, the dominant suppression relationship varying from one environment to another (e.g. growing season, nitrogen dose. The observed overyielding was not statistically significant. The ratio of actual to expected yield and the relative yield total of several mixtures exceeded slightly one. As a conclusion, the yield advantage of mixtures was marginal. As a rule, the mixtures were not more stable than monocultures as determined by the coefficient of variation. However, the yield of some mixtures varied less than the yield of the most stable monoculture.

Line tester analysis of yield and yield related attributed in different sunflower genotypes

International Nuclear Information System (INIS)

Din, S.U.; Khan, M.A.; Usman, K.; Sayal, O.U.

2014-01-01

This paper encompasses the study of line * tester analysis to chalk out genetic implications regarding yield and yield relating components in different genotypes of sunflower. Eight parents (four CMS lines and four restorers) along with their sixteen F1 hybrids were considered and planted in Randomized Complete Block Design (RCBD) replicated thrice at experimental area of Oilseed Research Program, National Agriculture Research Centre (NARC), Islamabad, Pakistan in 2011. Combining ability for some important morphological traits included days to flower initiation, days to flower completion, days to maturity, plant height, head diameter and seed yield plant-1. In this concern general combining ability (GCA), reciprocals combining ability (RCA) and specific combining ability (SCA) for all traits were studied. The GCA and SCA variances due to lines and testers interaction were significant for all the characters. However, the magnitude of GCAs from CMS lines (females) and restorers (pollinators) were higher than the SCA indicating preponderance of additive genes in the expression of all the traits. Among the lines, CMS-HA-54 whereas in testers, RHP-71, by manifesting maximum GCA effects were considered as the best general combiners for almost all the traits indicating the presence of more additive gene effects in these parents, therefore may serve as potential parents for hybridization and to improve the characters studied. Among the F1 hybrids, CMS HA-99 * RHP-76 (1.54, 212.65) and CMS HA-101 * RHP-73 (0.91, 432.73) were found as the best specific combiners for head or capitulum and seed yield. Hence, if farming community and researchers include these hybrids in their selection and hybridization program for the trait under study optimum result may be obtained. (author)

Evaluation of Yield and Yield Components of Black Cumin (Nigella sativa L. under different Plant Density and Limited Irrigation Condition

Directory of Open Access Journals (Sweden)

Sh Rezvan Beidokhti

2012-10-01

Full Text Available Research on crop response to deficit irrigation is important to reduce agriculture water use in areas where water is limited resource. Using drought resistant landraces with irrigation scheduling based on phenological stages in semi-arid and arid regions may provide an opportunity to optimize irrigation efficiency and water savings in these regions. In order to evaluate of yield and yield components of black cumin under different plant density and limited irrigation condition an experiment was conducted in Research Farm of Islamic Azad University of Damghan during growing season of 2007-2008. The experimental treatments were arranged in split plots based on a complete randomized block design with three replications. The limited irrigation (based on phenological stages treatments were included: cutting irrigation at blooming (folded flowers, cutting irrigation at flowering stage, cutting irrigation at seed formation and normal weekly irrigation (control were allocated to the main plots and different plant density: 100, 150, 200 and 250 plant per square meter (m2 were allocated to sub plots. The results showed that the effect of limited irrigation, plant density and their interaction on plant height, number of follicle, follicle weight, number of seed, 1000 seed weight, seed yield, biological yield and harvest index Black Cumin. The highest yield and yield components was obtained in normal irrigation (control and 200 plant density and the lowest yield were obtained when irrigation cut at the blooming stage and 250 plant density. There was a significant correlation between seed yield and number (r=0.90, 1000 seed weight (r=0.95 and biological yield (r=0.97. Optimum plant density of black cumin was decreased under limited irrigation treatments. Under normal (control and limited irrigation, optimum plant density was 200 and 150 plant per (m2 respectively.

Effect of saline irrigation water on yield and yield components of rice ...

African Journals Online (AJOL)

vaio

2013-05-29

May 29, 2013 ... levels at different growth stages of rice on yield and its components. Treatments included ... Therefore, irrigation with saline water at the early growth stages has more negative effect on ...... diversification. Land Degrad. Dev.

Dispersive analysis of {omega}{yields}3{pi} and {phi}{yields}3{pi} decays

Energy Technology Data Exchange (ETDEWEB)

Niecknig, Franz; Kubis, Bastian; Schneider, Sebastian P. [Universitaet Bonn, Helmholtz-Institut fuer Strahlen- und Kernphysik (Theorie) and Bethe Center for Theoretical Physics, Bonn (Germany)

2012-05-15

We study the three-pion decays of the lightest isoscalar vector mesons, {omega} and {phi}, in a dispersive framework that allows for a consistent description of final-state interactions between all three pions. Our results are solely dependent on the phenomenological input for the pion-pion P-wave scattering phase shift. We predict the Dalitz plot distributions for both decays and compare our findings to recent measurements of the {phi}{yields}3{pi} Dalitz plot by the KLOE and CMD-2 collaborations. Dalitz plot parameters for future precision measurements of {omega}{yields}3{pi} are predicted. We also calculate the {pi}{pi} P-wave inelasticity contribution from {omega}{pi} intermediate states. (orig.)

The Role of Iron and Zinc on Tuber Yield and Yield Components of Potato

Directory of Open Access Journals (Sweden)

Elham Jam

2015-08-01

Full Text Available The soils of potato production fields in Ardabil due to alkalinity and not having a proper crop rotations are deficient in micronutrients. To evaluate the effect of these micronutrients on the yield and some traits affecting potato tubers an experiment was conducted in a complete randomized block design with three replications in Ardabil during 2012. Micronutrient treatments used were the various concentrations of iron and zinc (0.002, 0.004 and 0.008 concentrations of these elements as Fe1Zn1, Fe1Zn2, Fe1Zn3, Fe2Zn1, Fe2Zn2, Fe2Zn3, Fe3Zn1 and Fe3Zn2 and a control treatment (Fe0Zn0. Analysis of variance of traits under study showed statistically significant differences among treatments in terms of tuber yield, number of tubers per plant, tuber size, skin thickness and volumetric weight and dry weight of tubers. The highest tuber yield (48.10 t.ha-1 and maximum skin thickness were obtained from Fe1Zn3 treatment. The highest tuber number belonged to Fe2Zn1 (0.004 and 0.002 concentrations of iron and zinc and Fe1Zn3 (0.002 and 0.008 concentrations of iron and zinc. Tuber weights higher than 35 grams and higest volumetric tuber weight were produced by using Fe3Zn2. The conclusion is this that using Fe1Zn3 traetment (0.002 and 0.008 concentrations resulted in highest tuber yield and thickness of tuber skin.

Yield of Echocardiogram and Predictors of Positive Yield in Pediatric Patients: A Study in an Urban, Community-Based Outpatient Pediatric Cardiology Clinic.

Science.gov (United States)

Billa, Ramya Deepthi; Szpunar, Susan; Zeinali, Lida; Anne, Premchand

2018-01-01

The yield of outpatient echocardiograms varies based on the indication for the echocardiogram and the age of the patient. The purpose of this study was to determine the cumulative yield of outpatient echocardiograms by age group and reason for the test. A secondary aim was to determine the predictors of a positive echocardiogram in an outpatient cardiology clinic at a large community teaching hospital. We retrospectively reviewed the charts of 891 patients who had a first-time echocardiogram between 2011 and 2015. Positive yield was defined as echocardiographic findings that explained the reason for the echocardiogram. The overall positive yield was 8.2%. Children between birth and 3 months of age had the highest yield (34.2%), and children between 12 and 18 years of age had the lowest yield (1%). Patients with murmurs (18.1%) had the highest yield compared with patients with other signs or symptoms. By age group and reason, the highest yields were as follows: 0 to 3 months of age, murmur (39.2%); 4 to 11 months of age, >1 symptom (50%); and 1 to 5 years of age, shortness of breath (66.7%). Based on our study, the overall yield of echocardiograms in the outpatient pediatric setting is low. Age and symptoms should be considered before ordering an echocardiogram.

Effects of Salinity and Nitrogen Application Methods on Yield and Yield Components of Wheat (Triticum aestivum L.

Directory of Open Access Journals (Sweden)

R Farshid

2012-07-01

Full Text Available To evaluate interaction of salinity stress and nitrogen use methods on yield and yield components, in experiment was conducted in split plot in randomized complete block with 3 replications. Treatments included: salinity of irrigation water levels 1.5, 4.4 and 7.9 ds/m as main plots, and nitrogen treatments 1. using N fertilizer at 3 stage in soil, 2. using two third N fertilizer in soil at planting and tillering and heading and one third in form of foliar application of N at tillering, 4. using and one third in form of foliar application at heading, 3. Using two third of N fertilizer in soil at planting one third of N fertilizer in soil at planting and two third in form of foliar application at tillering and heading, as sub plots. Results this study showed that increased in salt stress significant decreased total yield components such that showed decrease 41/5 kg/h in yield with increase in per unite salinity. Also methods of nitrogen application in salinity condition, have significant effects on total yield components. At the tillering, one stage of foliar with soil application of urea could increase spike no. m-2 and kernels of spike compared with other treatments. Foliar application of urea at heading stage increased kernels weight.

Effect of irrigation and nitrogen fertilizer levels on yield and yield components of dill (Anethum graveolens L.

Directory of Open Access Journals (Sweden)

S. Madadi Bonab

2016-05-01

Full Text Available In order to investigate the effect of irrigation and nitrogen fertilizer on yield and yield components of (Anethum graveolens L., a field experiment was performed in Agricultural Research Farm of the University of Tabriz, Iran, during growing season of 2009-2010. The experiment was carried out as split plot based on randomized complete block design with three replications. Irrigation treatments (irrigation after 70, 100, 130 mm evaporation from class A pan and nitrogen levels (0, 40, 80, 120 kg.ha-1 were allocated to main and sub-plots, respectively. The results showed that nitrogen fertilizer had significant (p≤0.05 effect on minor diameter umbrella, 1000-seed weight, seed yield and harvest index. However, irrigation and effect between irrigation and nitrogen were not affected any of the traits. The greatest minor diameter umbrella was obtained with control nitrogen treatment and maximum 1000-seed weight, harvest index and seed yield were obtained from 40 kg.ha-1 nitrogen. There was no any significant difference between 40 and 80 kg.ha-1 nitrogen levels. Therefore, it seems that for producing the highest yield application of 40 kg.ha-1 nitrogen is suitable. As water deficit no significant effects on this traits, of dill, it can be concluded that dill is a tolerant plant to drought stress.

Closing yield gaps: perils and possibilities for biodiversity conservation.

Science.gov (United States)

Phalan, Ben; Green, Rhys; Balmford, Andrew

2014-04-05

Increasing agricultural productivity to 'close yield gaps' creates both perils and possibilities for biodiversity conservation. Yield increases often have negative impacts on species within farmland, but at the same time could potentially make it more feasible to minimize further cropland expansion into natural habitats. We combine global data on yield gaps, projected future production of maize, rice and wheat, the distributions of birds and their estimated sensitivity to changes in crop yields to map where it might be most beneficial for bird conservation to close yield gaps as part of a land-sparing strategy, and where doing so might be most damaging. Closing yield gaps to attainable levels to meet projected demand in 2050 could potentially help spare an area equivalent to that of the Indian subcontinent. Increasing yields this much on existing farmland would inevitably reduce its biodiversity, and therefore we advocate efforts both to constrain further increases in global food demand, and to identify the least harmful ways of increasing yields. The land-sparing potential of closing yield gaps will not be realized without specific mechanisms to link yield increases to habitat protection (and restoration), and therefore we suggest that conservationists, farmers, crop scientists and policy-makers collaborate to explore promising mechanisms.

Effects of municipal sewage sludge doses on the yield, some yield ...

African Journals Online (AJOL)

STORAGESEVER

2008-09-03

Sep 3, 2008 ... Whereas grain yield, which was the highest component was ... land application, many studies have been performed ... grain. Analysis of variance was used to compare treatment ... een 17.0 - 164.0 cm depending on the environmental .... municipal sewage sludge for the stabilization of soil contaminated by.

Effects of Foliar Application of Nitrogen, Zinc and Manganese on Yield, Yield Components and Grain Quality of Chickpea in Two Growing Seasons

Directory of Open Access Journals (Sweden)

B. Shirani

2015-09-01

Full Text Available To study the effects of foliar application of zinc, manganese and nitrogen on yield, yield components and grain quality of chickpea (Cicer arientinum L. two experiments, one in autumn and the other in spring were conducted at Research Farm, Shahrekord University in 2009-2010 growing season each as a randomized complete block design with three replications. The treatments were foliar application of zinc sulfate, manganese sulfate zinc sulfate and manganese sulfate mixture, nitrogen and distilled water (as control. The results showed that planting season had a significant effect on plant height, 100-seed weight and seed yield. All measured traits, except plant height, increased in winter compared to spring growing season. This increase was more than 12% for grain yield. Foliar application of nutrients significantly affected seed yield and seed yield components. Foliar application of nitrogen, presumably, through significant increase in number of pods per plant, number of seeds per plant and 100-seed weight, increased the grain yield by 6.2% compared to control. Foliar application × planting season interactions were significant for plant height and number of pods per plant. Foliar application of nitrogen caused a significant increase in grain yield and protein content. Foliar application of zinc sulphate significantly increased Zn content of grains however it did not affect seed yield. In conclusion, foliar application of nitrogen could be suggested for increasing protein and grain yield in chickpea under similar conditions to that of the present study.

Yield performance and stability of CMS-based triticale hybrids.

Science.gov (United States)

Mühleisen, Jonathan; Piepho, Hans-Peter; Maurer, Hans Peter; Reif, Jochen Christoph

2015-02-01

CMS-based triticale hybrids showed only marginal midparent heterosis for grain yield and lower dynamic yield stability compared to inbred lines. Hybrids of triticale (×Triticosecale Wittmack) are expected to possess outstanding yield performance and increased dynamic yield stability. The objectives of the present study were to (1) examine the optimum choice of the biometrical model to compare yield stability of hybrids versus lines, (2) investigate whether hybrids exhibit a more pronounced grain yield performance and yield stability, and (3) study optimal strategies to predict yield stability of hybrids. Thirteen female and seven male parental lines and their 91 factorial hybrids as well as 30 commercial lines were evaluated for grain yield in up to 20 environments. Hybrids were produced using a cytoplasmic male sterility (CMS)-inducing cytoplasm that originated from Triticumtimopheevii Zhuk. We found that the choice of the biometrical model can cause contrasting results and concluded that a group-by-environment interaction term should be added to the model when estimating stability variance of hybrids and lines. midparent heterosis for grain yield was on average 3 % with a range from -15.0 to 11.5 %. No hybrid outperformed the best inbred line. Hybrids had, on average, lower dynamic yield stability compared to the inbred lines. Grain yield performance of hybrids could be predicted based on midparent values and general combining ability (GCA)-predicted values. In contrast, stability variance of hybrids could be predicted only based on GCA-predicted values. We speculated that negative effects of the used CMS cytoplasm might be the reason for the low performance and yield stability of the hybrids. For this purpose a detailed study on the reasons for the drawback of the currently existing CMS system in triticale is urgently required comprising also the search of potentially alternative hybridization systems.

Statistical modelling and deconvolution of yield meter data

DEFF Research Database (Denmark)

Tøgersen, Frede Aakmann; Waagepetersen, Rasmus Plenge

Data for yield maps can be obtained from modern combine harvesters equipped with a differential global positioning system and a yield monitoring system. Due to delay and smoothing effects in the combine harvester the recorded yield data for a location represents a shifted weighted average of yiel...

Predicting Great Lakes fish yields: tools and constraints

Science.gov (United States)

Lewis, C.A.; Schupp, D.H.; Taylor, W.W.; Collins, J.J.; Hatch, Richard W.

1987-01-01

Prediction of yield is a critical component of fisheries management. The development of sound yield prediction methodology and the application of the results of yield prediction are central to the evolution of strategies to achieve stated goals for Great Lakes fisheries and to the measurement of progress toward those goals. Despite general availability of species yield models, yield prediction for many Great Lakes fisheries has been poor due to the instability of the fish communities and the inadequacy of available data. A host of biological, institutional, and societal factors constrain both the development of sound predictions and their application to management. Improved predictive capability requires increased stability of Great Lakes fisheries through rehabilitation of well-integrated communities, improvement of data collection, data standardization and information-sharing mechanisms, and further development of the methodology for yield prediction. Most important is the creation of a better-informed public that will in turn establish the political will to do what is required.

Genetic variability and heritability estimates of some polygenic traits in upland cotton

International Nuclear Information System (INIS)

Baloch, M.J.

2004-01-01

Plant breeders are more interested in genetic variance rather than phenotypic variance because it is amenable to selection and bring further improvement in the character. Twenty-eight F/sub 2/ progenies were tested in two environments so as to predict genetic variances, heritability estimates and genetic gains. Mean squares for locations were significant for all the five traits suggesting that genotypes performed differently under varying environments. Genetic variances, in most cases, however, were about equal to that of phenotypic variances consequently giving high heritability estimates and significant genetic gains. The broad sense heritability estimates were; 94.2, 92.9, 33.6, 81.9 and 86.9% and genetic gains were; 30.19, 10.55,0.20,0.89 and 1.76 in seed cotton yield, bolls per plant, lint %, fibre length and fibre uniformity ratio, respectively. Substantial genetic variances and high heritability estimates implied that these characters could be improved through selection from segregating populations. (author)

Measurement of branching ratios and CP asymmetries for the decays B{sup 0}{yields}{pi}{sup +}{pi}{sup -}, B{sup 0}{yields}K{sup +}{pi}{sup -}, B{sup 0}{yields}K{sup +}K{sup -}

Energy Technology Data Exchange (ETDEWEB)

Prothmann, Kolja Andreas

2013-01-30

We present measurements of the branching fractions and CP violation parameters for the decay channels B{sup 0}{yields}{pi}{sup +}{pi}{sup -}, B{sup 0}{yields}K{sup +}{pi}{sup -} and B{sup 0}{yields}K{sup +}K{sup -}. The final Belle dataset of 772 million B anti B pairs produced at the {Upsilon}(4S) resonance at the KEKB asymmetric-energy e{sup +}e{sup -} collider is used. For the branching fractions, we obtain B(B{sup 0}{yields}{pi}{sup +}{pi}{sup -})=(5.63{+-} 0.16(stat){+-} 0.16(syst)) x 10{sup -6}, B(B{sup 0}{yields}K{sup {+-}}{pi}{sup -+})=(18.71{+-}0.25(stat){+-} 0.37(syst)) x 10{sup -6}, B(B{sup 0}{yields}K{sup +}K{sup -})<14 x 10{sup -8} at 90% CL. For the CP-asymmetries, we obtain following values: A{sub CP}(B{sup 0}{yields}{pi}{sup +}{pi}{sup -})=0.33{+-}0.06(stat){+-}0.03 (syst), S{sub CP}(B{sup 0}{yields}{pi}{sup +}{pi}{sup -})=-0.64{+-}0.08(stat){+-}0.03(syst), A{sub CP}(B{sup 0}{yields}K{sup {+-}}K{sup -+})=-0.061{+-}0.014(stat){+-}0.008 (syst), where A{sub CP} and S{sub CP} represent direct and mixing-induced CP violation, respectively. For the CP-violating weak phase {phi}{sub 2} we exclude the region 23.8 <{phi}{sub 2}<66.8 at the 1{sigma} level. A model independent test of new physics using a sum rule in the K{pi} system yields a mild deviation from the standard model of -0.289{+-}0.139(stat){+-}0.064(syst) with a 1.9{sigma} significance.

Variation of inulin content, inulin yield and water use efficiency for inulin yield in Jerusalem artichoke genotypes under different water regimes

Science.gov (United States)

The information on genotypic variation for inulin content, inulin yield and water use efficiency of inulin yield (WUEi) in response to drought is limited. This study was to investigate the genetic variability in inulin content, inulin yield and WUEi of Jerusalem artichoke (Helianthus tuberosus L.) ...

Yielding and shear banding in soft glassy materials

NARCIS (Netherlands)

Fall, A.; Paredes, J.; Bonn, D.

2010-01-01

Yield stress fluids have proven difficult to characterize, and a reproducible determination of the yield stress is difficult. We study two types of yield stress fluids (YSF) in a single system: simple and thixotropic ones. This allows us to show that simple YSF are simply a special case of

Maximum credibly yield for deuteriuim-filled double shell imaging targets meeting requirements for yield bin Category A

Energy Technology Data Exchange (ETDEWEB)

Wilson, Douglas Carl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Loomis, Eric Nicholas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-17

We are anticipating our first NIF double shell shot using an aluminum ablator and a glass inner shell filled with deuterium shown in figure 1. The expected yield is between a few 10¹⁰ to a few 10¹¹ dd neutrons. The maximum credible yield is 5e+13. This memo describes why, and what would be expected with variations on the target. This memo evaluates the maximum credible yield for deuterium filled double shell capsule targets with an aluminum ablator shell and a glass inner shell in yield Category A (< 10¹⁴ neutrons). It also pertains to fills of gas diluted with hydrogen, helium (³He or ⁴He), or any other fuel except tritium. This memo does not apply to lower z ablator dopants, such as beryllium, as this would increase the ablation efficiency. This evaluation is for 5.75 scale hohlraum targets of either gold or uranium with helium gas fills with density between 0 and 1.6 mg/cc. It could be extended to other hohlraum sizes and shapes with slight modifications. At present only laser pulse energies up to 1.5 MJ were considered with a single step laser pulse of arbitrary shape. Since yield decreases with laser energy for this target, the memo could be extended to higher laser energies if desired. These maximum laser parameters of pulses addressed here are near the edge of NIF’s capability, and constitute the operating envelope for experiments covered by this memo. We have not considered multiple step pulses, would probably create no advantages in performance, and are not planned for double shell capsules. The main target variables are summarized in Table 1 and explained in detail in the memo. Predicted neutron yields are based on 1D and 2D clean simulations.

Influence of yield surface curvature on the macroscopic yielding and ductile failure of isotropic porous plastic materials

Science.gov (United States)

Dæhli, Lars Edvard Bryhni; Morin, David; Børvik, Tore; Hopperstad, Odd Sture

2017-10-01

Numerical unit cell models of an approximative representative volume element for a porous ductile solid are utilized to investigate differences in the mechanical response between a quadratic and a non-quadratic matrix yield surface. A Hershey equivalent stress measure with two distinct values of the yield surface exponent is employed as the matrix description. Results from the unit cell calculations are further used to calibrate a heuristic extension of the Gurson model which incorporates effects of the third deviatoric stress invariant. An assessment of the porous plasticity model reveals its ability to describe the unit cell response to some extent, however underestimating the effect of the Lode parameter for the lower triaxiality ratios imposed in this study when compared to unit cell simulations. Ductile failure predictions by means of finite element simulations using a unit cell model that resembles an imperfection band are then conducted to examine how the non-quadratic matrix yield surface influences the failure strain as compared to the quadratic matrix yield surface. Further, strain localization predictions based on bifurcation analyses and imperfection band analyses are undertaken using the calibrated porous plasticity model. These simulations are then compared to the unit cell calculations in order to elucidate the differences between the various modelling strategies. The current study reveals that strain localization analyses using an imperfection band model and a spatially discretized unit cell are in reasonable agreement, while the bifurcation analyses predict higher strain levels at localization. Imperfection band analyses are finally used to calculate failure loci for the quadratic and the non-quadratic matrix yield surface under a wide range of loading conditions. The underlying matrix yield surface is demonstrated to have a pronounced influence on the onset of strain localization.

Analysis of Yield and Yield Related Traits Variability of Winter Wheat (Triticum aestivum L. Cv. Izolda and Double Haploid Lines

Directory of Open Access Journals (Sweden)

Kozdój Janusz

2015-12-01

Full Text Available The yield-forming potential of winter wheat is determined by several factors, namely total number of shoots per plant and total number of spikelets per spike. The field experiments were conducted during three vegetation seasons at the Plant Breeding and Acclimatization Institute – National Research Institute (PBAI–NRI, located in Radzików, Poland. The objective of this study was a comparative analysis of the structural yield-forming factor levels, which determine grain yield per spike and per plant of the DH lines and standard Izolda cultivar. Results indicate that several DH lines showed some differences in tested morphological structures of plant, yield factor levels and in grain yield per spike and per plant in comparison to standard Izolda, regardless of the year. Mean grain yield per plant of DH lines was 26.5% lower in comparison to standard Izolda only in the second year of study. It was caused by a reduction of productive tillers number. Structural yield-forming potential of DH lines was used in 38% and 59% and in case of Izolda in 47% and 61% (the second and the third year of experiment, respectively. The mean grain yield per spike of DH lines was 14.8% lower than Izolda cultivar only in third year of experiment and it was caused by about 12% lower number of grains per spike. Structural yield-forming potential of DH spikes was used in 82.4%, 85.4% and 84.9% and in case of Izolda in 83.8%, 87% and 89.5% (the first, the second and the third year of experiment, respectively. The grain yield per winter wheat plant (both DH lines and standard Izolda was significantly correlated with the number of productive tillers per plant (r = 0.80. The grain yield per winter wheat spike (both DH lines and Izolda cultivar was significantly and highly correlated with the number of grains per spike (r = 0.96, number of fertile spikelets per spike (r = 0.87 and the spike length (r = 0.80. Variation of spike and plant structural yield-forming factors

Development of high yielding mutants in lentil

International Nuclear Information System (INIS)

Rajput, M.A.; Sarwar, G.; Siddiqui, K.A.

2001-01-01

Full text: Lentil (Lens culinaris Medik.) locally known as Masoor, is the second most important rabi pulse crop, after chickpea, in Pakistan. It is cultivated on an area of over 63,400 ha, which constitutes about 4.83% of the total area under pulses. The annual production of the crop is 28,200 tones with an average yield of 445 kg/ha. Yield at the national level is very low, about one-half of the world's yield, which is mainly due to non-availability of high yield potential genotypes. Keeping in view the importance of mutants in developing a large number of new varieties, an induced mutations programme was initiated at AEARC, Tandojam during 1987-88, to develop high yielding varieties in lentil. For this, seeds of two lentil varieties, 'Masoor-85' and 'ICARDA-8' had been irradiated with gamma-rays ranging from 100-600 Gy in NIAB, Faisalabad during 1990. Selections were made in M2 on the basis of earliness, plant height, branches/plant and 100 grain weight. After confirming these mutants in M3 they were promoted in station yield trials and studied continuously for three consecutive years (1993- 1995). Overall results revealed that these mutants have consistent improvement of earliness in flowering and maturity. Plant height also increased in all mutant lines except AEL 23/40/91 where reduction in this attribute was observed as compared to parent variety. Mutant lines AEL 49/20/91 and AEL 13/30/91 showed improvement in 100 grain weight. The improvement of some agronomic characters enhanced the yield of mutant lines in comparison to parent varieties (Masoor-85 and ICARDA-8). The diversity in yield over the respective parents was computed from 6.94 to 60.12%. From these encouraging results it is hoped that mutant lines like AEL 12/30/91 and AEL 49/20/91 may serve as potential lentil genotypes in future. (author)

Modelling crop yield in Iberia under drought conditions

Science.gov (United States)

Ribeiro, Andreia; Páscoa, Patrícia; Russo, Ana; Gouveia, Célia

2017-04-01

The improved assessment of the cereal yield and crop loss under drought conditions are essential to meet the increasing economy demands. The growing frequency and severity of the extreme drought conditions in the Iberian Peninsula (IP) has been likely responsible for negative impacts on agriculture, namely on crop yield losses. Therefore, a continuous monitoring of vegetation activity and a reliable estimation of drought impacts is crucial to contribute for the agricultural drought management and development of suitable information tools. This works aims to assess the influence of drought conditions in agricultural yields over the IP, considering cereal yields from mainly rainfed agriculture for the provinces with higher productivity. The main target is to develop a strategy to model drought risk on agriculture for wheat yield at a province level. In order to achieve this goal a combined assessment was made using a drought indicator (Standardized Precipitation Evapotranspiration Index, SPEI) to evaluate drought conditions together with a widely used vegetation index (Normalized Difference Vegetation Index, NDVI) to monitor vegetation activity. A correlation analysis between detrended wheat yield and SPEI was performed in order to assess the vegetation response to each time scale of drought occurrence and also identify the moment of the vegetative cycle when the crop yields are more vulnerable to drought conditions. The time scales and months of SPEI, together with the months of NDVI, better related with wheat yield were chosen to perform a multivariate regression analysis to simulate crop yield. Model results are satisfactory and highlighted the usefulness of such analysis in the framework of developing a drought risk model for crop yields. In terms of an operational point of view, the results aim to contribute to an improved understanding of crop yield management under dry conditions, particularly adding substantial information on the advantages of combining

Path and ridge regression analysis of seed yield and seed yield components of Russian wildrye (Psathyrostachys juncea Nevski) under field conditions

DEFF Research Database (Denmark)

Wang, Quanzhen; Zhang, Tiejun; Cui, Jian

2011-01-01

The correlations among seed yield components, and their direct and indirect effects on the seed yield (Z) of Russina wildrye (Psathyrostachys juncea Nevski) were investigated. The seed yield components: fertile tillers m-2 (Y1), spikelets per fertile tillers (Y2), florets per spikelet- (Y3), seed...

Sequential Path Model for Grain Yield in Soybean

Directory of Open Access Journals (Sweden)

Mohammad SEDGHI

2010-09-01

Full Text Available This study was performed to determine some physiological traits that affect soybean,s grain yield via sequential path analysis. In a factorial experiment, two cultivars (Harcor and Williams were sown under four levels of nitrogen and two levels of weed management at the research station of Tabriz University, Iran, during 2004 and 2005. Grain yield, some yield components and physiological traits were measured. Correlation coefficient analysis showed that grain yield had significant positive and negative association with measured traits. A sequential path analysis was done in order to evaluate associations among grain yield and related traits by ordering the various variables in first, second and third order paths on the basis of their maximum direct effects and minimal collinearity. Two first-order variables, namely number of pods per plant and pre-flowering net photosynthesis revealed highest direct effect on total grain yield and explained 49, 44 and 47 % of the variation in grain yield based on 2004, 2005, and combined datasets, respectively. Four traits i.e. post-flowering net photosynthesis, plant height, leaf area index and intercepted radiation at the bottom layer of canopy were found to fit as second-order variables. Pre- and post-flowering chlorophyll content, main root length and intercepted radiation at the middle layer of canopy were placed at the third-order path. From the results concluded that, number of pods per plant and pre-flowering net photosynthesis are the best selection criteria in soybean for grain yield.

Response of switchgrass yield to future climate change

International Nuclear Information System (INIS)

Tulbure, Mirela G; Wimberly, Michael C; Owens, Vance N

2012-01-01

A climate envelope approach was used to model the response of switchgrass, a model bioenergy species in the United States, to future climate change. The model was built using general additive models (GAMs), and switchgrass yields collected at 45 field trial locations as the response variable. The model incorporated variables previously shown to be the main determinants of switchgrass yield, and utilized current and predicted 1 km climate data from WorldClim. The models were run with current WorldClim data and compared with results of predicted yield obtained using two climate change scenarios across three global change models for three time steps. Results did not predict an increase in maximum switchgrass yield but showed an overall shift in areas of high switchgrass productivity for both cytotypes. For upland cytotypes, the shift in high yields was concentrated in northern and north-eastern areas where there were increases in average growing season temperature, whereas for lowland cultivars the areas where yields were projected to increase were associated with increases in average early growing season precipitation. These results highlight the fact that the influences of climate change on switchgrass yield are spatially heterogeneous and vary depending on cytotype. Knowledge of spatial distribution of suitable areas for switchgrass production under climate change should be incorporated into planning of current and future biofuel production. Understanding how switchgrass yields will be affected by future changes in climate is important for achieving a sustainable biofuels economy. (letter)

On the yield stress of complex materials

Science.gov (United States)

Calderas, F.; Herrera-Valencia, E. E.; Sanchez-Solis, A.; Manero, O.; Medina-Torres, L.; Renteria, A.; Sanchez-Olivares, G.

2013-11-01

In the present work, the yield stress of complex materials is analyzed and modeled using the Bautista-Manero-Puig (BMP) constitutive equation, consisting of the upper-convected Maxwell equation coupled to a kinetic equation to account for the breakdown and reformation of the fluid structure. BMP model predictions for a complex fluid in different flow situations are analyzed and compared with yield stress predictions of other rheological models, and with experiments on fluids that exhibit yield stresses. It is shown that one of the main features of the BMP model is that it predicts a real yield stress (elastic solid or Hookean behavior) as one of the material parameters, the zero shear-rate fluidity, is zero. In addition, the transition to fluid-like behavior is continuous, as opposed to predictions of more empirical models.

Hot spots of wheat yield decline with rising temperatures.

Science.gov (United States)

Asseng, Senthold; Cammarano, Davide; Basso, Bruno; Chung, Uran; Alderman, Phillip D; Sonder, Kai; Reynolds, Matthew; Lobell, David B

2017-06-01

Many of the irrigated spring wheat regions in the world are also regions with high poverty. The impacts of temperature increase on wheat yield in regions of high poverty are uncertain. A grain yield-temperature response function combined with a quantification of model uncertainty was constructed using a multimodel ensemble from two key irrigated spring wheat areas (India and Sudan) and applied to all irrigated spring wheat regions in the world. Southern Indian and southern Pakistani wheat-growing regions with large yield reductions from increasing temperatures coincided with high poverty headcounts, indicating these areas as future food security 'hot spots'. The multimodel simulations produced a linear absolute decline of yields with increasing temperature, with uncertainty varying with reference temperature at a location. As a consequence of the linear absolute yield decline, the relative yield reductions are larger in low-yielding environments (e.g., high reference temperature areas in southern India, southern Pakistan and all Sudan wheat-growing regions) and farmers in these regions will be hit hardest by increasing temperatures. However, as absolute yield declines are about the same in low- and high-yielding regions, the contributed deficit to national production caused by increasing temperatures is higher in high-yielding environments (e.g., northern India) because these environments contribute more to national wheat production. Although Sudan could potentially grow more wheat if irrigation is available, grain yields would be low due to high reference temperatures, with future increases in temperature further limiting production. © 2016 John Wiley & Sons Ltd.

Bulk density calculations from prompt gamma ray yield

International Nuclear Information System (INIS)

Naqvi, A.A.; Nagadi, M.M.; Al-Amoudi, O.S.B.; Maslehuddin, M.

2006-01-01

Full text: The gamma ray yield from a Prompt Gamma ray Neutron Activation Analysis (PGNAA) setup is a linear function of element concentration and neutron flux in a the sample with constant bulk density. If the sample bulk density varies as well, then the element concentration and the neutron flux has a nonlinear correlation with the gamma ray yield [1]. The measurement of gamma ray yield non-linearity from samples and a standard can be used to estimate the bulk density of the samples. In this study the prompt gamma ray yield from Blast Furnace Slag, Fly Ash, Silica Fumes and Superpozz cements samples have been measured as a function of their calcium and silicon concentration using KFUPM accelerator-based PGNAA setup [2]. Due to different bulk densities of the blended cement samples, the measured gamma ray yields have nonlinear correlation with calcium and silicon concentration of the samples. The non-linearity in the yield was observed to increase with gamma rays energy and element concentration. The bulk densities of the cement samples were calculated from ratio of gamma ray yield from blended cement and that from a Portland cement standard. The calculated bulk densities have good agreement with the published data. The result of this study will be presented

simulating rice yields under climate change scenarios using

African Journals Online (AJOL)

Prof. Adipala Ekwamu

The effects of climate change on rice production and yield cannot be overlooked in finding measures to increase production and yield. The CERES-Rice (Ver. 4.0) model was calibrated and evaluated for use in simulating rice yields under different climate change scenarios in Ghana using data from the Anum Valley ...

Rice yield estimation with multi-temporal Radarsat-2 data

Science.gov (United States)

Chen, Chi-Farn; Son, Nguyen-Thanh; Chen, Cheng-Ru

2015-04-01

Rice is the most important food crop in Taiwan. Monitoring rice crop yield is thus crucial for agronomic planners to formulate successful strategies to address national food security and rice grain export issues. However, there is a real challenge for this monitoring purpose because the size of rice fields in Taiwan was generally small and fragmented, and the cropping calendar was also different from region to region. Thus, satellite-based estimation of rice crop yield requires the data that have sufficient spatial and temporal resolutions. This study aimed to develop models to estimate rice crop yield from multi-temporal Radarsat-2 data (5 m resolution). Data processing were carried out for the first rice cropping season from February to July in 2014 in the western part of Taiwan, consisting of four main steps: (1) constructing time-series backscattering coefficient data, (2) spatiotemporal noise filtering of the time-series data, (3) establishment of crop yield models using the time-series backscattering coefficients and in-situ measured yield data, and (4) model validation using field data and government's yield statistics. The results indicated that backscattering behavior varied from region to region due to changes in cultural practices and cropping calendars. The highest correlation coefficient (R2 > 0.8) was obtained at the ripening period. The robustness of the established models was evaluated by comparisons between the estimated yields and in-situ measured yield data showed satisfactory results, with the root mean squared error (RMSE) smaller than 10%. Such results were reaffirmed by the correlation analysis between the estimated yields and government's rice yield statistics (R2 > 0.8). This study demonstrates advantages of using multi-temporal Radarsat-2 backscattering data for estimating rice crop yields in Taiwan prior to the harvesting period, and thus the methods were proposed for rice yield monitoring in other regions.

Study of pp{yields}pp{eta} reaction at threshold; Etude de la reaction pp{yields}pp{eta} au seuil

Energy Technology Data Exchange (ETDEWEB)

Taleb, A

1994-11-01

The {eta} production has been studied through the pp {yields} pp{eta} reaction at threshold. Data were taken at the Synchrotron of the ``Laboratoire National Saturne``. The detection in coincidence of the two protons scattered near 0 deg and analysed with the magnetic spectrometer SPES3 allows the reconstruction of missing mass spectra for the {eta} signature. A simulation program which takes into account all the experimental set up characteristics has been realized and tested through the pp {yields} d{pi}{sup +} reaction detected simultaneously with pp {yields} pp{eta}. The generated proton momentum spectra for pp {yields} pp{eta} show a pronounced {eta} mass dependence. This characteristic, connected to the kinematical properties of pp {yields} pp{eta} at threshold, is used to extract the mass of the meson {eta}. The obtained value, m{sub {eta}} = 547.65 {+-} 0.18 MeV, is in good agreement with measurement done recently through the pd {yields} {sup H}e{eta} reaction. The total cross section {sigma}{sub t} of pp {yields} pp{eta} measured at 1260, 1265 and 1300 MeV presents a strong energy dependence. This cross section increases less with energy than the phase-space. The influence of p-p and {eta}-p final state interactions in our measurements is studied. Our results are compared with theoretical predictions and assess the dominant character of the baryonic resonance N{sup *}(1535) in the {eta} mechanism production at threshold. These experimental results give an energy dependence which is not well reproduced by the theoretical predictions. This discrepancy could be an incorrect description of the {eta}-p interaction in the models. (author). 48 refs., 60 figs., 15 tabs.

Are GM Crops for Yield and Resilience Possible?

Science.gov (United States)

Paul, Matthew J; Nuccio, Michael L; Basu, Shib Sankar

2018-01-01

Crop yield improvements need to accelerate to avoid future food insecurity. Outside Europe, genetically modified (GM) crops for herbicide- and insect-resistance have been transformative in agriculture; other traits have also come to market. However, GM of yield potential and stress resilience has yet to impact on food security. Genes have been identified for yield such as grain number, size, leaf growth, resource allocation, and signaling for drought tolerance, but there is only one commercialized drought-tolerant GM variety. For GM and genome editing to impact on yield and resilience there is a need to understand yield-determining processes in a cell and developmental context combined with evaluation in the grower environment. We highlight a sugar signaling mechanism as a paradigm for this approach. Copyright © 2017 Elsevier Ltd. All rights reserved.

Estimating yield gaps at the cropping system level.

Science.gov (United States)

Guilpart, Nicolas; Grassini, Patricio; Sadras, Victor O; Timsina, Jagadish; Cassman, Kenneth G

2017-05-01

Yield gap analyses of individual crops have been used to estimate opportunities for increasing crop production at local to global scales, thus providing information crucial to food security. However, increases in crop production can also be achieved by improving cropping system yield through modification of spatial and temporal arrangement of individual crops. In this paper we define the cropping system yield potential as the output from the combination of crops that gives the highest energy yield per unit of land and time, and the cropping system yield gap as the difference between actual energy yield of an existing cropping system and the cropping system yield potential. Then, we provide a framework to identify alternative cropping systems which can be evaluated against the current ones. A proof-of-concept is provided with irrigated rice-maize systems at four locations in Bangladesh that represent a range of climatic conditions in that country. The proposed framework identified (i) realistic alternative cropping systems at each location, and (ii) two locations where expected improvements in crop production from changes in cropping intensity (number of crops per year) were 43% to 64% higher than from improving the management of individual crops within the current cropping systems. The proposed framework provides a tool to help assess food production capacity of new systems ( e.g. with increased cropping intensity) arising from climate change, and assess resource requirements (water and N) and associated environmental footprint per unit of land and production of these new systems. By expanding yield gap analysis from individual crops to the cropping system level and applying it to new systems, this framework could also be helpful to bridge the gap between yield gap analysis and cropping/farming system design.

The stochastic seasonal behavior of energy commodity convenience yields

International Nuclear Information System (INIS)

Mirantes, Andrés García; Población, Javier; Serna, Gregorio

2013-01-01

This paper contributes to the commodity pricing literature by consistently modeling the convenience yield with its empirically observed properties. Specifically, in this paper, we show how a four-factor model for the stochastic behavior of commodity prices, with two long- and short-term factors and two additional seasonal factors, may accommodate some of the most important empirically observed characteristics of commodity convenience yields, such as the mean reversion and stochastic seasonality. Based on this evidence, a theoretical model is presented and estimated to characterize the commodity convenience yield dynamics that are consistent with previous findings. We also show that commodity price seasonality is better estimated through convenience yields than through futures prices. - Highlights: • Energy commodity convenience yields exhibit mean reversion and stochastic seasonality. • We present a model for convenience yields accounting for their observed characteristics. • Commodity price seasonality is better estimated through convenience yields

Experimental study on yield behavior of Daqing crude oil

Energy Technology Data Exchange (ETDEWEB)

Hou, Lei [China University of Petroleum, College of Mechanical and Transportation Engineering, Beijing (China)

2012-07-15

The yield behavior of Daqing crude oil was studied by means of multi-mode controlled-stress tests with a high-precision stress controlled rheometer. Two experiments of creep and constant stress loading rate were performed. The yield stress of gelled crude oil was dependent on the test conditions such as the stress loading time and the stress loading rate, but the yield strain did not change with test conditions. The yield strain did exist objectively and it can be used as the criterion for the yielding of the structure of gelled crude oil. The yield strain of gelled oil was studied through experiments of creep, constant stress loading rate, oscillatory shear stress increase, and constant shear rate. The yield strain of gelled crude oil decreased with the increasing gel strength. The experiment of constant speed increase of stress showed the strain softening phenomena for low gel strength oil. (orig.)

Soybean growth and yield under cover crops

Directory of Open Access Journals (Sweden)

Priscila de Oliveira

2013-04-01

Full Text Available The use of cover crops in no-tillage systems can provide better conditions for the development of soybean plants with positive effects on grain yield and growth analysis techniques allow researchers to characterize and understand the behavior of soybean plants under different straw covers. Thus, the aim of this study was to characterize, using growth analysis, yield components and agronomic performance of soybean under common bean, Brachiaria brizantha and pearl millet straws. The experiment was performed on a soil under cerrado in the municipality of Santo Antônio de Goiás, GO. The experiment was arranged in a randomized complete block design with three treatments (cover crops and five replications. Soybean grain yield was lower in the B. brizantha straw treatment (3,708 kg ha-1 than both in the pearl millet (4.772 kg ha-1 and common bean straw treatments (5,200 kg ha-1. The soybean growth analysis in B. brizantha, pearl millet and common bean allowed characterizing the variation in the production of dry matter of leaves, stems, pods and total and leaf area index that provided different grain yields. The cover crop directly affects the soybean grain yield.

Yield Potential of Hemp (Cannabis sativa L.) Cultivars in Denmark

DEFF Research Database (Denmark)

Deleuran, Lise Christina; Flengmark, Poul Kristiansen

2005-01-01

In order to determine the yield potential of fibre hemp in Denmark, defined as seed yield, biomass, stem and fibre production, five cultivars were evaluated in field trials at two sites during 1998-2000. The total dry matter yield, stem yield, fibre yield, fibre percent, plant height, and seed...

Effect of seed rate on growth, yield components and yield of mash bean grown under irrigated conditions of arid uplands of Balochistan, Pakistan

International Nuclear Information System (INIS)

Aachakzai, A.K.K.; Taran, S.A.

2011-01-01

A field experiment was carried out to investigate the effects of six different seed rates viz., 15, 17.5, 20, 22.5, 25 and 27.5 kg ha/sup -1/ on the growth, yield and yield attributes of mash bean Vigna mungo (L.) Hepper). This study was conducted for two consecutive years at the Agriculture Research Institute (ARI) under the existing semi-arid climatic, edaphic and water conditions of Quetta, Balochistan. Results revealed that plant population, pods plant/sup -1/, grain yield plant/sup -1/ and grain yield ha/sup -1/ were significantly (p<0.05 influenced by varying seed rates. However, other mentioned growth and yield attributes did not respond significantly. Statistically and numerically a maximum yield plant/sup -1/ (20.98 g) and yield ha/sup -1/ (3120 kg) were obtained in applied seed at the rate of 20 kg ha/sup -1/. Whereas, the same was obtained for plant population and plant height in applied seed rate of 25 kg ha/sup -1/. However, maximum number of branches plant/sup -1/ (4.22) was received for applied seeds at the rate of 15 kg ha/sup -1/. Therefore, seed at the rate of 20 kg ha/sup -1/ seems optimum which could be due to the most desirable population or planting density in the existing environmental conditions of Quetta. Results further revealed that only plant population plot/sup -1/ (r=0.481), and yield plant/sup -1/ (r=0.569) were significantly and positively correlated with grain yield ha/sup -1/, while all other remaining growth and yield attributes exhibited insignificant association with grain yield ha/sup -1/. Hence these two parameters i.e., planting density and grain yield plant/sup -1/ should be given more consideration while deciding about selection criteria for mash bean under irrigated conditions of arid uplands of Balochistan. (author)

"Rändkeha" loomine Pärnus / Heili Einasto

Index Scriptorium Estoniae

Einasto, Heili

2007-01-01

Rahvusvahelisest tantsuprojektist "The Migrant Body" ("Rändkeha"). Projektis osalevad viie maa (Eesti, Itaalia, Rumeenia, Hollandi, Inglismaa) koreograafid ja tantsijad rändavad tantsukava koostades ühest riigist teise. Eesti poolt osalevad projektis tantsija Einar Lints, produtsent, koreograaf Teet Kask, fotograaf-videokunstnik Mark Raidpere ja artikli autor

Enhancing the competitiveness of an SMME in the automotive industry through the introduction of laser based manufacturing. A case study

CSIR Research Space (South Africa)

Burger, HP

2006-01-01

Full Text Available to synthetic fibre the cut is produced by melting the individual fibres resulting in a semi sealed cut edge that is totally free of fraying and lint. This paper illustrates how the introduction of laser cutting into the manufacturing process not only solved...

Fourier transform infrared macro-imaging of botanical cotton trash

Science.gov (United States)

The marketability of cotton fiber is directly tied to the trash comingled with it. Trash can contaminate cotton during harvesting, ginning, and processing. Thus, the removal of trash is important from field to fabric. An ideal prerequisite to removing trash from lint is identifying what trash types...

Investigation of Tolerance, Yield and Yield Components of Wheat Cultivars to Salinity of Irrigation Water at Sensitive Stages of Growth

Directory of Open Access Journals (Sweden)

B Saadatian

2013-04-01

Full Text Available This research in order to study of tolerance ability of wheat cultivates yield and yield components to salinity of irrigation water at sensitive stages of growth, was carried out as a factorial based on a randomized complete block design with 3 replications at greenhouse of Agricultural Faculty of Bu-Ali Sina University, in 2009. Treatments were included wheat cultivars of Alvand, Tous, Sayson and Navid and salinity of irrigation water induced by sodium chloride at five levels of 0, 4, 8, 12 and 16 dS m-1. The results showed that percentage and rate of emergence, plant height, 1000-grain weight, number of seed per spike, number of spike per pot, biological and grain yield reduced by increasing salinity level. At all stress levels Navid cv. had highest emergence percentage. In non-stress and 4 dS m-1, Alvand cv. and at higher levels of stress, Tous cv. had high height in reproductive phase. At control and 4 dS m-1, Sayson cv. and at 8, 12 and 16 dS m-1, Tous cv. in majority of yield and yield components traits had significant superior than other cultivars. Tolerance index of Sayson cv. at 4 and 8 dS m-1 was more than other cultivars but at 12 and 16 dS m-1, maximum value of this index was belonged to Tous cv. At all salinity levels, Alvand cv. had least tolerance index to stress. Number of spike per pot had maximum direct effect on grain yield of wheat cultivars in stress condition. Also indirect effect of biological yield via number of spike per pot than other its indirect effects, had maximum share in wheat seed yield.

[Fission product yields of 60 fissioning reactions]. Final report

International Nuclear Information System (INIS)

Rider, B.F.

1995-01-01

In keeping with the statement of work, I have examined the fission product yields of 60 fissioning reactions. In co-authorship with the UTR (University Technical Representative) Talmadge R. England ''Evaluation and Compilation of Fission Product Yields 1993,'' LA-UR-94-3106(ENDF-349) October, (1994) was published. This is an evaluated set of fission product Yields for use in calculation of decay heat curves with improved accuracy has been prepared. These evaluated yields are based on all known experimental data through 1992. Unmeasured fission product yields are calculated from charge distribution, pairing effects, and isomeric state models developed at Los Alamos National Laboratory. The current evaluation has been distributed as the ENDF/B-VI fission product yield data set

Effects of Mineral N and P Fertilizers on Yield and Yield Components of Flooded Lowland Rice on Vertisols of Fogera Plain, Ethiopia

Directory of Open Access Journals (Sweden)

Heluf Gebrekidan

2006-10-01

Full Text Available Despite its very recent history of cultivation in Ethiopia, rice is one of the potential grain crops that could contribute to the efforts for the realization of food security in the country. However, the scientific information available with regards to the response of flooded rice to N and P fertilizers for its optimum production on Vertisols of Fogera Plain is very limited. Therefore, a field experiment was conducted on Vertisols of Fogera plain, northern Ethiopia to study the yield and yield components response of rice and to establish the optimum N and P fertilizer levels required for improved grain yield of flooded rice. Six levels of N (0, 30, 60, 90, 120 and 150 kg ha−1 and five levels of P (0, 13.2, 26.4, 39.6 and 52.8 kg ha−1 laid down in a randomized complete block design with four replications were used as treatments. Nitrogen was applied in two equal splits (50% basal and 50% at maximum tillering as urea and the entire dose of P was applied basal as triple super phosphate at sowing. The main effects of N and P fertilizer levels showed significant differences (P ≤ 0.01 for all yield and yield components studied. The effects of N by P interaction were significant only for grain yield (P ≤ 0.05, number of panicles per m2 (P ≤ 0.01, number of spikelets per panicle (P ≤ 0.05 and plant height (P ≤ 0.01 among the different yield and yield components studied. Application of N and P significantly (P ≤ 0.01 increased grain yield of rice up to the levels of 60 kg N and 13.2 kg P ha−1. However, maximum grain yield (4282 kg ha−1 was obtained with the combined application of 60 kg N and 13.2 kg P ha−1, and the yield advantage over the control was 38.49% (1190 kg ha−1. Moreover, application of both N and P fertilizers have increased the magnitudes of the important yield attributes including number of panicles per m2, number of spikelets per panicle, panicle length, dry matter accumulation, straw yield and plant height

The Effect of Different Fertilizer Management on Yield and Yield Components of Black Seed (Nigella sativa L.

Directory of Open Access Journals (Sweden)

P rezvani moghaddam

2017-08-01

Full Text Available Introduction Given the importance of nitrogen for improving the quantitative and qualitative yield of crops (Rodrigues et al., 2006 and the need for application of chemical fertilizers in intensive agriculture to get the maximum production, nitrogen supply in adequate amounts by ecologically avowed resources is known as one of the main challenges during transition from conventional to organic farming (Rodrigues et al., 2006. Considering the sustainable nitrogen management, reconstruction and rehabilitation of agroecosystems depends on reduction the nitrogen losses due to leaching, soil erosion and volatilization (Kizilkaya, 2008. For this purpose, the use of eco-friendly bio based fertilizers that are derived from natural origin, known as effective and enforceable approaches. In this regards, the proper use of manure and free-living aerobic bacteria of soils, such as Azotobacter and Azospirillum as well as mycorrhizal inoculation which can be used as a biological fertilizers, can particularly be considered (Kizilkaya, 2008. With regard to all mentioned above, the current study was aimed to evaluate the effects of biological, organic and inorganic resources of nitrogen on yield and yield components of black seed (Nigella sativa L.. Materials and methods The field experiment was conducted at Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, in years of 2009-2010. Experimental site was located in a semi-arid region, Khorasan Province, Northeast of Iran. The soil texture was silty loam, pH 8.36, electrical conductivity 3.72 dS.m-1, total N 0.095% and 0.195% organic carbon. The available P and K contents were 5.76 and 0.378 ppm, respectively. Experimental design was arranged by using a completely randomized block design with three replications. Experimental treatments included chemical fertilizer (urea, urea + nitroxin, urea + mycorrhizae, urea + nitroxin + mycorrhizae, urea + biosulfur, manure, manure + nitroxin, manure + mycorrhizae

Yield Improvement in barley by using gamma irradiation

International Nuclear Information System (INIS)

Ben-Amer, Ibrahim Mohammed

1993-01-01

Sixty two mutant lines in the M4 generation were studies for one year for yield components (heads per plant kernals per head and kernal weight). Four mutant lines out yielded the parent but the differences being significant only with the mutant 2-6-26. This is mainly due to significant increase in number of beads per plant. Yield per plant was correlated with number of heads per plant. In a 2-year field experiment, mutant 2-6-26 out yielded the parent variety, the difference being significant only in one experiment (1988-89). The increase in nitrogen rate from 0 to 100 kg/ha increased yield significantly. mutant 2-6-26 produced 415 g grains/m 2 in the 1987-88 experiment; in 1988-89 experiment, its yields were 426, 610 and 594 g grains/m 2 for the 0, 100 and 200 kg N/ha respectively. The differences in kernal weight were highly significant only in 1988-89 experiment. Lodging was low in 1987-88 experiment due to moisture stress. In 1988-89 experiment, Lodging increased with the increase in N application rate. None of the mutant lines showed any improvement in the resistance to lodging. Mutant 2-6-26 is very promising. It will be evaluated in large yield-trials at different locations in the country. (author)

Responsiveness of cold tolerant chickpea characteristics in fall and spring planting: II. yield and yield components

Directory of Open Access Journals (Sweden)

ahmad nezami

2009-06-01

Full Text Available Previous research in Mashhad collection chickpeas (MCC has shown that there are some cold tolerant genotypes for fall planting in the highlands. To obtain more detailed information about the reaction of these genotypes to fall and spring planting, the yield and yield component responses of 33 chickpea genotypes (32 cold tolerant genotypes and one susceptible genotypes to four planting dates (28 Sep., 16 Oct., 2 Nov., and 7 Mar. were evaluated in 2000-2001 growing season. The experiment was conducted at the experimental field of college of agriculture, Ferdowsi University of Mashhad as a split plot design with two replications. The planting dates were imposed as main plot and chickpea genotypes as subplot. Effects of planting date and genotype on percent of plant survival (PPS after winter, number. of pod per plant, 100 seed weight, yield and Harvest Index (HI were significant (p

Managment oriented analysis of sediment yield time compression

Science.gov (United States)

Smetanova, Anna; Le Bissonnais, Yves; Raclot, Damien; Nunes, João P.; Licciardello, Feliciana; Le Bouteiller, Caroline; Latron, Jérôme; Rodríguez Caballero, Emilio; Mathys, Nicolle; Klotz, Sébastien; Mekki, Insaf; Gallart, Francesc; Solé Benet, Albert; Pérez Gallego, Nuria; Andrieux, Patrick; Moussa, Roger; Planchon, Olivier; Marisa Santos, Juliana; Alshihabi, Omran; Chikhaoui, Mohamed

2016-04-01

The understanding of inter- and intra-annual variability of sediment yield is important for the land use planning and management decisions for sustainable landscapes. It is of particular importance in the regions where the annual sediment yield is often highly dependent on the occurrence of few large events which produce the majority of sediments, such as in the Mediterranean. This phenomenon is referred as time compression, and relevance of its consideration growths with the increase in magnitude and frequency of extreme events due to climate change in many other regions. So far, time compression has ben studied mainly on events datasets, providing high resolution, but (in terms of data amount, required data precision and methods), demanding analysis. In order to provide an alternative simplified approach, the monthly and yearly time compressions were evaluated in eight Mediterranean catchments (of the R-OSMed network), representing a wide range of Mediterranean landscapes. The annual sediment yield varied between 0 to ~27100 Mg•km-2•a-1, and the monthly sediment yield between 0 to ~11600 Mg•km-2•month-1. The catchment's sediment yield was un-equally distributed at inter- and intra-annual scale, and large differences were observed between the catchments. Two types of time compression were distinguished - (i) the inter-annual (based on annual values) and intra- annual (based on monthly values). Four different rainfall-runoff-sediment yield time compression patterns were observed: (i) no time-compression of rainfall, runoff, nor sediment yield, (ii) low time compression of rainfall and runoff, but high compression of sediment yield, (iii) low compression of rainfall and high of runoff and sediment yield, and (iv) low, medium and high compression of rainfall, runoff and sediment yield. All four patterns were present at inter-annual scale, while at intra-annual scale only the two latter were present. This implies that high sediment yields occurred in

[Milk yield and environmental factors: Multiple regression analysis of the association between milk yield and udder health, fertility data and replacement rate].

Science.gov (United States)

Fölsche, C; Staufenbiel, R

2014-01-01

The relationship between milk yield and both fertility and general animal health in dairy herds is discussed from opposing viewpoints. The hypothesis (1) that raising the herd milk yield would decrease fertility results, the number of milk cells as an indicator for udder health and the replacement rate as a global indicator for animal health as well as increasing the occurrence of specific diseases as a herd problem was compared to the opposing hypotheses that there is no relationship (2) or that there is a differentiated and changing relationship (3). A total of 743 herd examinations, considered independent, were performed in 489 herds between 1995 and 2010. The milk yield, fertility rate, milk cell count, replacement rate, categorized herd problems and management information were recorded. The relationship between the milk yield and both the fertility data and animal health was evaluated using simple and multiple regression analyses. The period between calving and the first service displayed no significant relationship to the herd milk yield. Simple regression analysis showed that the period between calving and gestation, the calving interval and the insemination number were significantly positively associated with the herd milk yield. This positive correlation was lost in multiple regression analysis. The milk cell count and replacement rate using both the simple and multiple regression analyses displayed a significant negative relationship to the milk yield. The alternative hypothesis (3) was confirmed. A higher milk yield has no negative influence on the milk cell count and the replacement rate in terms of the udder and general health. When parameterizing the fertility, the herd milk yield should be considered. Extending the resting time may increase the milk yield while preventing a decline in the insemination index.

Sorghum yield and associated satellite-derived meteorological ...

African Journals Online (AJOL)

Sorghum yield and associated satellite-derived meteorological parameters in semi-arid Botswana. ... African Crop Science Journal ... Sorghum (Sorghum bicolor) yield for five seasons (2005/6 to 2009/10) from the Botswana Department of Crop ... Key Words: Coefficient of determination, NDVI, Pearson correlation ...

The Effect of Vesicular Arbuscular Mycorrhizal (VAM on Yield and Yield Components of Three Sorghum (Sorghum bicolor Cultivars

Directory of Open Access Journals (Sweden)

A. Mehraban

2012-10-01

Full Text Available To evaluate the influence of vesicular arbuscular mycorrhizal (VAM on yield and yield components of three sorghum cultivars, a factorial experiment based randomized complete block design with four replications was carried out in 2007, at the Agricultural Research Center of Zahak, Iran. The treatments were different mycorrhiza species in three levels: without mycorrhiza (M1, Glomus etanicatum (M2 and G. mosseae(M3 and three cultivars of sorghum: local cultivars (C1, KGS25 (C2 and KGS29 (C3. The results showed that all of the traits measured were increased by inoculation of cultivars with mycorrhiza. The highest plant height (165.1 cm, stem diameter (1.61 cm, flag leaf length (27.22 cm, flag leaf width (3.67 cm and ear width (5.00 cm was obtained by inoculation of seed with Glumus etanicatum, and highest ear length (19.21 cm, ear number (2.51, seed number per ear (10252.11, 1000-seed weight (17.56 g and grain yield (1967.32 kg/ha by using Glumus mossea. The highest leaf width and length belonged to local cultivar, and the highest seed yield to KGS 29 cultivar. However, differences of other traits among sorghum cultivars were not significant. Based on the experimental results it can be concluded that highest grain yield may be obtained by inoculating seeds of KGS 29 with Glumus mossea.

Changes in diurnal temperature range and national cereal yields

Energy Technology Data Exchange (ETDEWEB)

Lobell, D

2007-04-26

Models of yield responses to temperature change have often considered only changes in average temperature (Tavg), with the implicit assumption that changes in the diurnal temperature range (DTR) can safely be ignored. The goal of this study was to evaluate this assumption using a combination of historical datasets and climate model projections. Data on national crop yields for 1961-2002 in the 10 leading producers of wheat, rice, and maize were combined with datasets on climate and crop locations to evaluate the empirical relationships between Tavg, DTR, and crop yields. In several rice and maize growing regions, including the two major nations for each crop, there was a clear negative response of yields to increased DTR. This finding reflects a nonlinear response of yields to temperature, which likely results from greater water and heat stress during hot days. In many other cases, the effects of DTR were not statistically significant, in part because correlations of DTR with other climate variables and the relatively short length of the time series resulted in wide confidence intervals for the estimates. To evaluate whether future changes in DTR are relevant to crop impact assessments, yield responses to projected changes in Tavg and DTR by 2046-2065 from 11 climate models were estimated. The mean climate model projections indicated an increase in DTR in most seasons and locations where wheat is grown, mixed projections for maize, and a general decrease in DTR for rice. These mean projections were associated with wide ranges that included zero in nearly all cases. The estimated impacts of DTR changes on yields were generally small (<5% change in yields) relative to the consistently negative impact of projected warming of Tavg. However, DTR changes did significantly affect yield responses in several cases, such as in reducing US maize yields and increasing India rice yields. Because DTR projections tend to be positively correlated with Tavg, estimates of yields

Expectations, Bond Yields and Monetary Policy

DEFF Research Database (Denmark)

Chun, Albert Lee

2011-01-01

expectations about inflation, output growth, and the anticipated path of monetary policy actions contain important information for explaining movements in bond yields. Estimates from a forward-looking monetary policy rule suggest that the central bank exhibits a preemptive response to inflationary expectations...... of this type may provide traders and policymakers with a new set of tools for formally assessing the reaction of bond yields to shifts in market expectations...

The effects of the regulated deficit irrigation on yield and some yield ...

African Journals Online (AJOL)

user

2011-05-16

May 16, 2011 ... human diet and environment, its production requires a significant amount of water due to its relatively shallow root system. Thus, the amount of ... should be applied. Drip irrigation, reduces deep percolation and evaporation ..... processing tomato yield, water table depth, soil salinity and profitability. Agric.

Effect of Irrigation with Wastewater and Foliar Application of Complete Fertilizer on Forage Yield and Yield Components of Foxtail Millet (Setaria italica

Directory of Open Access Journals (Sweden)

A Ahmadi Aghtape

2013-08-01

Full Text Available In order to study effect of irrigation with wastewater and foliar application of complete fertilizer on forage yield and seed yield and yield components of foxtail millet (Setaria italica. A split plot experiment based on randomized complete block design with three replications was conducted at the Agriculture Institute of Zabol University in year 2009. Treatments included three levels of irrigation: Irrigation with well water at all stages of grows (control, Irrigation with wastewater and tap water alternately, Irrigation with wastewater for all growing stages, as the main plot and sprayed with three levels of complete fertilizer (NATBA-LIB: Non spraying (control, sprayed with 600 and 1200 gram of complete fertilizer in each hectare, as were the subplots. Results showed that irrigation with wastewater and complete fertilizer sprayed had significant effect on all traits except leaf to stem ratio. Furthermore, among the irrigation treatments, irrigation with wastewater in total growing period, and wastewater and tap water alternately lead to significant increase in grain yield, forage yield and yield components. Among the sprayed treatments, sprayed with 1200 gram of complete fertilizer had highest forage yield and grain.

On yield gains and yield gaps in wheat-maize intercropping

OpenAIRE

Gou, Fang

2017-01-01

Intercropping is the cultivation of two or more crop species simultaneously in the same field, while relay intercropping means that the growing periods of the crop species are only partially overlapping. Intercropping has advantages with respect to productivity, resource capture, build-up of soil organic matter, and pest and disease suppression. This thesis aims to quantify and explain the yield advantages in wheat-maize relay intercropping and to assess the importance of intercropping for fo...

Central Bank Communication and the Yield Curve

DEFF Research Database (Denmark)

Leombroni, Matteo; Vedolin, Andrea; Venter, Gyuri

communication shocks have a significant impact, with intermediate maturities being affected the most; (ii) positive (negative) communication shocks significantly lower (raise) the yield spread between the peripheral and core countries; (iii) this cross-sectional difference arises after the 2008 financial crises......-for-yield investors....

Effects of Row Spacing and Plant Density on Yield and Yield Components of Sweet Corn in Climatic Conditions of Isfahan

Directory of Open Access Journals (Sweden)

N. Khodaeian

2013-06-01

Full Text Available To evaluate the effects of row spacing and plant density on yield and yield components of sweet corn, variety KSC403, an experiment was conducted in Research Farm of Isfahan University of Technology, Isfahan, Iran, in 2007, as randomized complete block design with a split-plot layout and three replications. The main plots were allocated to two row spacing (60 and 75 cm and the sub-plots accommodated four levels of plant density (50000, 70000, 90000 and 110000 plants per ha. There was significant increase in leaf area index, shoot dry weight, 100-grain fresh weight and grain fresh yield, as row width was decreased from 75 to 60 cm but the plant height was decreased. There was no significant effect of row spacing on number of rows per ear, number of grains per row and number of grains per ear. Plant height, leaf area index, shoot dry weight per m2 and number of ears per m2 were increased with an increase in plant density. The number of rows per ear, number of grains per row, number of grains per ear, 100-grain fresh weight and grain fresh yield were significantly higher under plant densities of 90000 and 110000 as compared to 50000 and 70000 plants per ha. There was significant interaction between row spacing and plant density for leaf area index, shoot dry weight, number of grains per ear, 100-grain fresh weight and grain fresh yield. Under all plant densities, the grain fresh yield was higher in 60-cm row width compared to 70-cm row width. However, the difference between these two row spacing was not significant in plant densities of 50000 and 110000 plants per ha. The highest grain fresh yield (33940 kg/ha was achieved under row spacing 60 cm and 70000 plants per ha and the least grain fresh yield (20750 kg/ha was obtained in under 75 cm row width and 110000 plants per ha. Considering the obtained results of this experiment, to have maximum grain fresh yield of sweet corn under Isfahan climate, the row spacing of 60 cm and plant density of

Fluence-dependent sputtering yield of micro-architectured materials

Energy Technology Data Exchange (ETDEWEB)

Matthes, Christopher S.R.; Ghoniem, Nasr M., E-mail: ghoniem@ucla.edu; Li, Gary Z.; Matlock, Taylor S.; Goebel, Dan M.; Dodson, Chris A.; Wirz, Richard E.

2017-06-15

Highlights: • Sputtering yield is shown to be transient and heavily dependent on surface architecture. • Fabricated nano- and Microstructures cause geometric re-trapping of sputtered material, which leads to a self-healing mechanism. • Initially, the sputtering yield of micro-architectured Mo is approximately 1/2 the value as that of a planar surface. • The study demonstrates that the sputtering yield is a dynamic property, dependent on the surface structure of a material. • A developed phenomenological model mathematically describes the transient behavior of the sputtering yield as a function of plasma fluence. - Abstract: We present an experimental examination of the relationship between the surface morphology of Mo and its instantaneous sputtering rate as function of low-energy plasma ion fluence. We quantify the dynamic evolution of nano/micro features of surfaces with built-in architecture, and the corresponding variation in the sputtering yield. Ballistic deposition of sputtered atoms as a result of geometric re-trapping is observed, and re-growth of surface layers is confirmed. This provides a self-healing mechanism of micro-architectured surfaces during plasma exposure. A variety of material characterization techniques are used to show that the sputtering yield is not a fundamental property, but that it is quantitatively related to the initial surface architecture and to its subsequent evolution. The sputtering yield of textured molybdenum samples exposed to 300 eV Ar plasma is roughly 1/2 of the corresponding value for flat samples, and increases with ion fluence. Mo samples exhibited a sputtering yield initially as low as 0.22 ± 5%, converging to 0.4 ± 5% at high fluence. The sputtering yield exhibits a transient behavior as function of the integrated ion fluence, reaching a steady-state value that is independent of initial surface conditions. A phenomenological model is proposed to explain the observed transient sputtering phenomenon, and to

correlation studies and path coefficient analysis for seed yield

African Journals Online (AJOL)

Prof. Adipala Ekwamu

African Crop Science Journal, Vol. 21, No. 1, pp. 51 - 59 ... Yield being a quantitative trait has complex inheritance, which is ... Analysis for seed yield and yield components in Ethiopian coriander. 53 ..... The financial assistance of Canadian.

Particle debonding using different yield criteria

DEFF Research Database (Denmark)

Legarth, Brian Nyvang; Kuroda, Mitsutoshi

2004-01-01

Effects of plastic anisotropy in relation to debonding of rigid inclusions embedded in an elastic-viscoplastic metal are studied. Full finite strain analyses are carried out for plane cells assuming plane stress or plane strain. The overall stress strain response is calculated, when the cell......-matrix debonding. Keeping all material parameters fixed, the material response of the plane strain cell is considerably affected, due to debonding at a much reduced overall plastic strain compared to the corresponding plane stress cell. (C) 2004 Elsevier SAS. All rights reserved....... extent and shape of the particular yield function considered. The required overall straining of the cell for debonding initiation is related to the extent of the yield surfaces, since a high yield stress promotes debonding. Additionally, the maximum overall stress level for the cell is lower for the Hill...

The Effect of Irrigation Intervals and Arbuscular Mycorrhizal Fungi on Chlorophyll Index, Yield and Yield Components of Grain Sorghum

Directory of Open Access Journals (Sweden)

J. Hamzei

2014-08-01

Full Text Available This experiment was carried out to study the effect of irrigation intervals and arbuscular mycorrhizal fungi on chlorophyll index, yield and yield components of grain sorghum. A factorial experiment was done based on randomized complete block design (RCBD with three replications at the Agriculture Research Station faculty of Agriculture, Bu- Ali Sina University in growing season of 2011. Irrigation intervals (7, 14 and 21 days with three levels of seed inoculation (control without inoculation, inoculation with Glomus mossea and inoculation with G. intraradices were the experimental treatments. Results indicated that the effect of irrigation intervals and mycorrhizal fungi were significant for traits of chlorophyll index, percentage of root symbiosis (PRS, number of grain per panicle, 1000 seed weight, grain yield and harvest index (HI. Maximum value for each trait was observed at G. mossea treatment. G. mossea treatment in comparison with G. intraradices and control treatment can increase the grain yield of sorghum up to 6.80 and 23.10%, respectively. Also, with increasing irrigation interval from 7 to 21 days, PRS increased up to 27.9%. Maximum value for grain yield (755 g m-2 was achieved at irrigation every 14 days and application of G. mossea treatment. But, there was no significant difference between irrigation sorghum plants every 14 days and application of G. mossea and irrigation every 7 days and application of either G. mossea or G. intraradices. In general, irrigation of sorghum plants every 14 days and supplying of G. mossea can produce the highest grain yield, while decreasing water consumption for sorghum production.

Effect of Foliar Application of Phosphorus and Water Deficit on Yield and Yield Components of Winter Wheat (Cultivar Alvand

Directory of Open Access Journals (Sweden)

M. Vafapour

2011-04-01

Full Text Available In order to study the effects of foliar application of phosphorus (P and water deficit on yield and yield components of winter wheat (Triticum aestivum L., cv. Alvand, a split-plot experiment, with completely randomized blocks design and three replications, was carried out at the Research Farm of Boyer Ahmad Agricultural and Natural Resources Research Station, 13 km west of Yasouj, in 2008-2009. The main plots were irrigation at three levels (1- full irrigation (control, 2- deficit irrigation from the stem elongation to booting stage, and 3- deficit irrigation from booting stage to the end of growth period and the subplots were five levels of foliar application of P fertilizer (0, 3, 6, 9 and 12 kg/ha KH2PO4. The results showed that the effects of different irrigation regimes and foliar application of P were significant on all traits, and their interaction was significant on plant height, number of grain per spike, grain yield and biological yield. Full irrigation and foliar application of 6 kg/ha P produced the highest grain and biological yield (6000 and 14170 kg/ha, respectively and deficit irrigation from the stem elongation to booting stage without foliar application of P produced the lowest grain and biological yield (2920 and 8219 kg/ha, respectively. Foliar application of P affects significantly the evaluated traits only in drought-stress treatments and its effect was not significant in full irrigation treatment. In general, foliar application of 9 kg/ha P compensated the losses in wheat due to drought stress.

Contamination sources, prevention, and research

Science.gov (United States)

Contamination is defined as anything other than cotton in cotton lint. Worldwide, contamination is on the rise and plastic contamination has increased at a faster rate than contamination overall. In the U.S., there are many sources of plastic contaminants, such as plastic trash that collects in cott...

The second lumbrical-interossei latency difference in carpal tunnel ...

African Journals Online (AJOL)

All were subjected to routine median motor nerve conduction study with stimulation at midpalm, wrist and elbow, median-versus-radial sensory comparison study and Second lumbrical-versus-interosseus (2L-INT) motor comparison study. Results: The results showed that the most sensitive tests were the median-radial ...

Marketing policies and economic interests in the cotton sector of Kenya

NARCIS (Netherlands)

Dijkstra, T.

1990-01-01

This report, which is based on field research carried out in 1988, examines the marketing arrangements for raw cotton, cotton lint and cotton seed in Kenya, as well as the relationships and conflicts between the actors involved. The report starts with the history of cotton production and marketing

Fourier transform infrared imaging of Cotton trash mixtures

Science.gov (United States)

There is much interest in the identification of trash types comingled with cotton lint. A good understanding of the specific trash types present can lead to the fabrication of new equipment which can identify and sort cotton trash found with cotton fiber. Conventional methods, including the High Vo...

Relationship between three cotton trash measurements: High Volume Instrumentation (HVI), Shirley Analyzer (SA), and Advanced Fiber Information System (AFIS)

Science.gov (United States)

Presence of non-lint materials (trashes) in commercial cotton bales at various amounts degrades the market values and further influences the end-use qualities. In order to ensure a fair trading, the USDA’s AMS has introduced the high volume instrument (HVI) measurement as a universal standard index....

Yield gap analysis of Chickpea under semi-arid conditions: A simulation study

Directory of Open Access Journals (Sweden)

seyed Reza Amiri Deh ahmadi

2016-05-01

Full Text Available Yield gap analysis provides an essential framework to prioritize research and policy efforts aimed at reducing yield constraints. To identify options for increasing chickpea yield, the SSM-chickpea model was parameterized and evaluated to analyze yield potentials, water limited yields and yield gaps for nine regions representing major chickpea-growing areas of Razavi Khorasan province. The average potential yield of chickpea for the locations was 2251 kg ha-1, while the water limited yield was 1026 kg ha-1 indicating a 54% reduction in yield due to adverse soil moisture conditions. Also, the average irrigated and rainfed actual yields were respectively 64% and 79% less than simulated potential and water limited yields. Maximum and minimum yield gap between potential yield and actual yield were observed in Quchan and Torbat-jam respectively. Generally, yield gap showed an increasing trend from the north (including Nishabur, Mashhad, Quchan and Daregaz regions to the south of the province (Torbat- Jam and Gonabad. In addition, yield gap between simulated water limited potential yield and rainfed actual yield were very low because both simulated water limiting potential and average rainfed actual yields were low in these regions. Yield gap analysis provides an essential framework to prioritize research and policy efforts aimed at reducing yield constraints. To identify options for increasing chickpea yield, the SSM-chickpea model was parameterized and evaluated to analyze yield potentials, water limited yields and yield gaps for nine regions representing major chickpea-growing areas of Razavi Khorasan province. The average potential yield of chickpea for the locations was 2251 kg ha-1, while the water limited yield was 1026 kg ha-1 indicating a 54% reduction in yield due to adverse soil moisture conditions. Also, the average irrigated and rainfed actual yields were respectively 64% and 79% less than simulated potential and water limited yields

Crop yield response to increasing biochar rates

Science.gov (United States)

The benefit or detriment to crop yield from biochar application varies with biochar type/rate, soil, crop, or climate. The objective of this research was to identify yield response of cotton (Gossypium hirsutum L.), corn (Zea mayes L.), and peanut (Arachis hypogaea L.) to hardwood biochar applied at...

FEM growth and yield data monocultures - Poplar

NARCIS (Netherlands)

Mohren, G.M.J.; Goudzwaard, L.; Jansen, J.J.; Oosterbaan, A.; Oldenburger, J.F.; Ouden, den J.

2016-01-01

The current database is part of the FEM growth and yield database, a collection of growth and yield data from even-aged monocultures (douglas fir, common oak, poplar, Japanese Larch, Norway spruce, Scots pine, Corsican pine, Austrian pine, red oak and several other species, with only a few plots,

On the design and implementation of a wafer yield editor

NARCIS (Netherlands)

Pineda de Gyvez, J.; Jess, J.A.G.

1989-01-01

An interactive environment is presented for the analysis of yield information required on modern integrated circuit manufacturing lines. The system estimates wafer yields and wafer-yield variations, quantifies regional yield variations within wafers, identifies clusters in wafers and/or in lots, and

Response of maize varieties to nitrogen application for leaf area profile, crop growth, yield and yield components

International Nuclear Information System (INIS)

Akmal, M.; Hameed-urRehman; Farhatullah; Asim, M.; Akbar, H.

2010-01-01

An experiment was conducted at NWFP Agricultural University, Peshawar, to study maize varieties and Nitrogen (N) rates for growth, yield and yield components. Three varieties (Azam, Jalal and Sarhad white) and three N rates (90, 120, 150, kg N ha/sup -1/) were compared. Experiment was conducted in a Randomized Complete Block design; split plot arrangement with 4 replications. Uniform and recommended cultural practices were applied during the crop growth. The results revealed that maize variety 'Jalal' performed relatively better crop growth rate (CGR) and leaf area profile (LAP) at nodal position one to six as compared to the other two varieties (Sarhad white and Azam). This resulted higher radiation use efficiency by the crop canopy at vegetative stage of development and hence contributed higher assimilates towards biomass production. Heavier grains in number and weight were due to higher LAP and taller plants of Jalal which yielded higher in the climate. Nitrogen applications have shown that maize seed yield increase in quadratic fashion with increased N to a plateau level. Considering soil fertility status and cropping system, the 150 kg ha/sup -1/ N application to maize variety Jalal in Peshawar is required for maximum biological and seed production. (author)

Effect of irrigation water salinity and zinc application on yield, yield components and zinc accumulation of wheat

Directory of Open Access Journals (Sweden)

mohamad ahmadi

2009-06-01

Full Text Available Salinity stress is one of the most important problems of agriculture in crop production in arid and semi arid regions. Under these conditions, in addition to management strategies, proper and adequate nutrition also has an important role in crop improvement. A greenhouse experiment was conducted to study the effect of 4 different irrigation water salinities (blank, 4, 8 and 12 dS m-1, prepared with 1:1 molar ratio of chlorides of calcium and sodium and magnesium sulphate salts. and 5 different zinc applications (0, 10, 20, 30 mg Kg-1 soil and foliar application of salt of zinc sulphate on yield, yield components and zinc concentration of wheat, using a completely randomized design, factorial with three replications. Plant height, spike length, 1000 grain weight, number of grain per spike, grain and straw yield was decreased by Irrigation water salinity. And all of these parameters were improved by zinc application except 1000 grain weight. Zinc absorption and concentration in straw and grain was decreased by Saline water compared to blank. And concentration of zinc significantly was increased in straw and grain by increase zinc application. The results indicated that, zinc application under low to medium salinity conditions improved growth and yield of wheat due to decreasing the impacts salinity.

Effect of the Yield Stress and r-value Distribution on the Earing Profile of Cup Drawing with Yld2000-2d Yield Function

Science.gov (United States)

Lou, Yanshan; Bae, Gihyun; Lee, Changsoo; Huh, Hoon

2010-06-01

This paper deals with the effect of the yield stress and r-value distribution on the earing in the cup drawing. The anisotropic yield function, Yld2000-2d yield function, is selected to describe the anisotropy of two metal sheets, 719B and AA5182-O. The tool dimension is referred from the Benchmark problem of NUMISHEET'2002. The Downhill Simplex method is applied to identify the anisotropic coefficients in Yld2000-2d yield function. Simulations of the drawing process are performed to investigate the earing profile of two materials. The earing profiles obtained from simulations are compared with the analytical model developed by Hosford and Caddell. Simulations are conducted with respect to the change of the yield stress and r-value distribution, respectively. The correlation between the anisotropy and the earing tendency is investigated based on simulation data. Finally, the earing mechanism is analyzed through the deformation process of the blank during the cup deep drawing. It can be concluded that ears locate at angular positions with lower yield stress and higher r-value while the valleys appear at the angular position with higher yield stress and lower r-value. The effect of the yield stress distribution is more important for the cup height distribution than that of the r-value distribution.

Evaluation of Yield, Yield Components and Essential Oil Content of Marigold (Calendula officinalis L. with the Use of Nitrogen and Vermicompost

Directory of Open Access Journals (Sweden)

Alireza Pazoki

2016-10-01

Full Text Available Environmenal problems resulting from application of nitrogen fertilizers in the production plant materials led agricultural specialists to use clean and alternative methods to towards the organic farming and use of organic fertilizers. In this study, thus, the effect of nitrogen and vermicompost fertilizer rates on yield, yield components, essential oil content and some morphological traits of marigold was studied in a split plot experiment based on completely randomized blocks design with 3 replications in Shahr-e-Rey region during 2013 growing season. Nitrogen rates with 3 levels (0, 60, 120 and 180 kg.ha-1 were assigned to main plots and vermicompost with 3 levels (0, 10, and 20 t.ha-1 to the sub plots. Mean comparison of simple effects indicated that the plants treated with 120 kg.ha-1 nitrogen fertilizer and 20 t.ha-1 organic fertilizer vermicompost produced higher trait values under study than control (non application of vermincompost. Interaction effect of experimented factors was significant on all traits under evaluation. Thus, highest seed yield (1567 kg.ha-1, biological yield (6664 kg.ha-1 and essential oil yield (8.85 kg.ha-1 obtained by the application of 120 kg.ha-1 nitrogen fertilizer and 20 t.ha-1 varmicompost. Based on the results obtained it could be said that nitrogen and vermicompost may improve seed and biological yield and yield components of marigold.

Relations between soil factors and herbage yields of natural ...

African Journals Online (AJOL)

Keywords: Cation exchange capacity; Correlation matrix; Nitrogen supplies; Root mass; Root measurements; Soil acidity; Soil variables; Soil water content; Soil water measurements; Yield measurements; nitrogen supply; ph; herbage yield; grassland; soils; productivity; soil depth; dry matter yield; grasses; water content; n; ...

Climate-induced yield variability and yield gaps of maize (Zea mays L.) in the Central Rift Valley of Ethiopia

NARCIS (Netherlands)

Kassie, B.T.; Ittersum, van M.K.; Hengsdijk, H.; Asseng, S.; Wolf, J.; Rotter, R.P.

2014-01-01

There is a high demand for quantitative information on impacts of climate on crop yields, yield gaps and their variability in Ethiopia, yet, quantitative studies that include an indication of uncertainties in the estimates are rare. A multi-model crop growth simulation approach using the two crop

Density responses and spatial distribution of cotton yield and yield components in jujube (Zizyphus jujube)/cotton (Gossypium hirsutum) agroforestry

NARCIS (Netherlands)

Wang, Qi; Han, Shuo; Zhang, Lizhen; Zhang, Dongsheng; Werf, van der Wopke; Evers, Jochem B.; Sun, Hongquan; Su, Zhicheng; Zhang, Siping

2016-01-01

Trees are the dominant species in agroforestry systems, profoundly affecting the performance of understory crops. Proximity to trees is a key factor in crop performance, but rather little information is available on the spatial distribution of yield and yield components of crop species under the

Influence of micronutrients and their method of application on yield and yield components of sunflower

International Nuclear Information System (INIS)

Baraich, A.A.K.; Gandahi, A.W.

2016-01-01

The sunflower (Helianthus annuus L.) has been recognized as a crop with high potentials that can successfully meet future oil requirements of the country. Formulation of micronutrients (MN) based fertilizer, in terms of application rate and method, and uptake of MN by sunflower has the ability not only to ensure nutrients availability to plants particularly in MN-limiting environments but also can manipulate the environmental hazards associated with over inorganic fertilization. To support this view, clear experimental evidence is still lacking. In addition, the current experiments aimed to evaluate the influence of MN and its method of application on yield and yield components of sunflower cultivars/hybrids. Three sunflower cultivars (HO-1, Hysun-39 and Ausigold-62) along with three MN (Z, B and Fe) and two application methods (soil and foliar) were used in the experiment. Three Zn application rate (3, 5 and 8 kg ha-1) along with 0.75 kg ha-1 B and 0.30 kg Fe ha-1 were used in four combinations such as 0-0-0, 0-0.75-0.30, 0-0.75-0.30, 3-0.75-0.30, 5-0.75-0.30, 8-0.75-0.30 kg Z, B and Fe ha-1, respectively. A control (no MN) treatment was also included for comparison. Two year averaged study exhibited that foliar application of Zn, B and Fe at rate of 8-0.30-0.75 kg ha-1 increased stem girth, head diameter, number of seeds head-1, seed weight head-1, seed index, oil content and seed yield by 21%, 27%, 13%, 34%, 19%, 24 and 31%, respectively over control. Among cultivars/hybrids, the hybrids HO-1 and Hysun-39 had taller plants, seed weight head-1, seeds head-1 and earlier in flowering and maturity. Flowering and maturity was delayed in Ausi Gold-62 with higher seed index and oil content. It is concluded that foliar application of micronutrients at the rate of 8+0.75+0.30 Zn, B and Fe kg ha-1 had substantially improved yield and yield related traits of sunflower cultivars HO-1, Hysun-39 and Ausi gold-62. (author)

The effects of vermicompost and chemical fertilizers on yield and yield components of marshmallow (Altheae officinalis L.)

OpenAIRE

A.A. Sadeghi; K. Bakhsh Kelarestaghi; K. Hajmohammadnia Ghalibaf

2016-01-01

In order to investigate the effects of vermicompost and chemical fertilizers on growth characteristics, yield and yield components of marshmallow (Altheaeofficinalis L.), a field experiment was conducted as factorial layout based on a randomized complete block design with three replications at Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, during growing season of 2012. Experimental treatments were designed based on 3 levels of vermicompost (0, 5 and 10 t ha-1) and 5 levels of ...

Effects of Chemical and Organic Fertilizers on Growth, Yield and Yield Component of Tomato (Lycopersicon sculentum L.

Directory of Open Access Journals (Sweden)

R Mirzaei Talarposhti

2017-03-01

Full Text Available Introduction Although using animal manures and crop residues as a traditional method for increasing soil fertility and crop yield has a long history but Conventional agricultural systems rely on the use of chemical fertilizer due to its immediate availability of nutrients. In many of modern agricultural systems using chemical fertilizers as a fast and easiest way to reduce nutrient deficiency and increasing soil fertility is considered. Intensive and continuous use of chemical fertilizers leads to decreasing the stability and sustainability of agricultural systems and also poses major threat to environment and human health. Organic fertilizers have positive effects on physiochemical and biological attributes of soil and could be classified in three different groups (i.e. Animal manures, green manure and composts.Using animal manure not only increase soil fertility but also could result in increasing infiltration, aeration and water holding capacity of soil. The main role of these fertilizers is related to physical change in soil. Different types of composts such as municipal waste compost and vermicompost also have similar positive effects, but usually the farmers observe the main effect of these organic fertilizers in long term. In order to investigate the effects of different types of organic fertilizers on growth indexes, yield and yield component of tomato (Lycopersicon sculentum L. current experiment was conducted. Materials and Methods The experiment was conducted based on randomized complete block design (RCBD with three replications and six treatments in the research station of Shahid Beheshti University. The experimental treatments were: Control or no fertilizer (NF, chemical fertilizer (CF, cow manure (CM, poultry manure (PM, vermicompost (VC and municipal waste compost (MC. Considering nitrogen concentration in all of the treatments different amounts of these fertilizers were used based on nitrogen recommendation for the field, so in

Yield gap analysis in long-term experiments with intensive rice cultivation

International Nuclear Information System (INIS)

Laureles, E.V.; Correa, T. Jr.; Buresh, R.J.

2007-01-01

The long-term continuous cropping experiment at IRRI is cultivated with three rice crops in a year, making it the world's most intensively cropped long-term rice experiment. The availability of comprehensive rice production records, compiled weather data, and tested crop models provides a means to evaluate long-term trends in measured and potential yields and yield gaps in this rice production system. Yield trends were assessed using the highest yielding cultivar in each cropping season from 1979 to 2005. Potential yield of the highest yielding cultivar in each season was determined using three rice models (ORYZA, TERM, and CERES) run with the actual transplanting and harvest dates for the cultivar. The yield gap was determined from the difference between the simulated potential grain yield and the measured grain yield. Measured and potential yields and the yield gap varied across seasons and years. Measured yields were higher in the dry season than in the early and late wet seasons. The yield gap tended to be higher in the wet season than in the dry season. Climatic parameters, particularly solar radiation, influenced the performance of rice cultivars. The relatively larger yield gaps in the late wet season than in the dry season were associated with increased spikelet sterility. The cumulative measured yield for the three annual rice crop was near 80 percent of the annual yield potential in years with best practices for fertilizer N and crop management. The long term trends suggest that effective timing and rates of N fertilization and effective control of diseases were critical in achieving 80 percent of the annual yield potential

Yield stress independent column buckling curves

DEFF Research Database (Denmark)

Stan, Tudor‐Cristian; Jönsson, Jeppe

2017-01-01

of the yield stress is to some inadequate degree taken into account in the Eurocode by specifying that steel grades of S460 and higher all belong to a common set of “raised” buckling curves. This is not satisfying as it can be shown theoretically that the current Eurocode formulation misses an epsilon factor......Using GMNIA and shell finite element modelling of steel columns it is ascertained that the buckling curves for given imperfections and residual stresses are not only dependent on the relative slenderness ratio and the cross section shape but also on the magnitude of the yield stress. The influence...... in the definition of the normalised imperfection magnitudes. By introducing this factor it seems that the GMNIA analysis and knowledge of the independency of residual stress levels on the yield stress can be brought together and give results showing consistency between numerical modelling and a simple modified...

Slifers revisited: a method for determining yields independent of radiochemical measurements

International Nuclear Information System (INIS)

Rambo, J.T.

1976-01-01

It would be very desirable if an independent method other than radiochemical measurement were available to determine the yields of low-yield events in the alluviums and tuffs of areas 2, 9, and 10 at the Nevada Test Site. The successful application of slifers to the measurement of yields from high-yield events suggests that under some conditions they may also be usable with low-yield events. This view is supported by the evidence discussed here, which is based on direct experience with slifer yield measurements for low-yield events in porous media. Suggested methods for improving slifer yield determinations and a method for determining yields independent of radiochemical measurements are offered

Effect of Plant Growth Promoting Rhizobacteria (PGPR on Phenological Traits, Grain Yield and Yield Components of Three Maize (Zea mays L. Cultivars

Directory of Open Access Journals (Sweden)

A Soleimani Fard

2013-11-01

Full Text Available To evaluate the effect of bio-fertilize on yield and its components in maize cultivars, an split plot experiment based on randomized complete bock design with three replications in was conducted in Payam-noor University of Ilam, Iran, in 2009-2010. Treatments were cultivar (SC604, SC704 and SC807 assigned to main plots and bio-fertilizer (non- inoculation, inoculation with Azetobacter, Azospirillum and dual inoculation ofAzotobacterand Azospirillum to subplots. The effect of cultivar on days to maturity, plant height, dry matter, ear length, stem diameter, number of grain per ear row, 1000-grain weight, grain yield, biological yield and protein content was significant cultivar. SC 704 had the highest dry matter (259.5 g.m-2, plant height (201.1 cm, number of grain per ear row (42.8 grain, grain yield (10850 kg.m-2, and biological yield (22040 kg.m-2. The effect of plant growth promoting rhizobacteria on all traits expect harvest index was significant. Dual inoculation ofAzotobacterand Azospirillum had the longest days to ear initiation (71.2 days, days to maturity (115.4 day, number of leaves above ear (5.6 ear, dry matter (240.4 g.m-2, ear length (24.3 cm, plant height (212.4 cm, seed number of rows per ear (14.5 row, number of grains per row (44.2 grain, grain yield (10190 kg.m-2, biological yield (21320 kg.m-2 and protein content (10.7%. Interaction effect of cultivar× plant growth promoting rhizobacteria on grain yield was significant. The highest and lowest grain yield was obtained from SC 704 and application of dual inoculation ofAzotobacterand Azospirillum (12320 kg.ha-1 and lowest from SC 604 when inoculation treatments were not used 7570 kg.ha-1 respectively.

Researches on Determination Yield and Yield Components of Some Common Vetch (Vicia sativa L. Genotypes in Ecological Conditions of Diyarbakır

Directory of Open Access Journals (Sweden)

Seyithan SEYDOŞOĞLU

2014-09-01

Full Text Available The research was conducted to determine yield and yield components of some common vetch genotypes in order to examine some of the traits, during 2011-2013 seasons in GAP International Agricultural Research and Training Center was carried out on the experimental field. In the study, a total of 20 different genotypes were used common vetch, field trials randomized block design with 3 replications was established. In the study, herbage yield, hay yield and seed yield in addition to days to %50 flowering duration, plant height, main stem length, main stem number, pod number per plant, grain number per pod as affecting yield some properties were also investigated. In both years of the study, days to %50 flowering duration and grain number per pod characteristics examined, except among genotypes for all other parameters are determined significant differences in statistical terms. According to the average of two years result; days to %50 flowering duration, plant height, main stem length, main stem number, pod number per plant, grain number per pod, herbage yield, hay yield, seed yield, 1000 seed weight were changed between 157.8-174.0 days, 33.9-62.6 cm, 52.0-83.3 cm, 1.6-2.6 number, 13.5-21.2 number, 4.7-5.6 number, 1522.0-3232.3 kg da-1, 308.0-919.5 kg da-1, 92.2-293.7 kg da-1, 46.5-84.5 g, respectively. According to these results, under the climate and soil conditions of Diyarbakır; for the grass production common vetch genotypes "D-135" was suggested and for the seed production common vetch genotypes "IFVS-715" and "GAP-59998" were suggested.

Studies on seed yield potential of some selected kenaf (Hibiscus ...

African Journals Online (AJOL)

SAM

2014-06-11

Jun 11, 2014 ... Kenaf seed yield depends on morpho-physiological traits between varieties, .... separated using Duncan's Multiple Range Test (DMRT) at 5% ... Mean squares derived from combined analysis of variance for seed yield and yield components in 20 .... environment interaction and yield stability in winter wheat.

Effect of Mycorrhiza Symbiosis on Yield, Yield Components and Water Use Efficiency of Sesame (Sesamum indicum L. Affected by Different Irrigation Regimes in Mashhad Condition

Directory of Open Access Journals (Sweden)

A Koocheki

2016-02-01

Full Text Available Introduction Plant association with mycorrhiza has been considered as one of the options to improve input efficiency particularly for water and nutrient - (Allen and Musik, 1993; Bolan, 1991. This has been due to kncreasing the absorbing area of the root and therefore better contact with water and nutrients. Inoculation with mycorrhiza enhances nutrient uptake with low immobility such as phosphorus and solphur-, improve association and could be an option to drought and other environmental abnormalities such as salinity (Rice et al., 2002. Moreover, higher water use efficiency (WUE for crops -has been reported in the literatures (Sekhara and Reddy, 1993.The sustainable use of scarce water resources in Iran is a priority for agricultural development. The pressure of using water in agriculture sector is increasing, so creating ways to improve water-use efficiency and taking a full advantage of available water are crucial. Water stress reduce crop yield by impairing the growth of crop canopy and biomass. Scheduling water application is very crucial for efficient use of drip irrigation system, as excessive irrigation reduces yield, while inadequate irrigation causes water stress and reduces production. The aim of present study was to evaluate the symbiotic effect of mycorrhiza on yield, yield components and water use efficiency of sesame under different irrigation regimes in Mashhad. Material and Methods In order to investigate the impact of inoculation with two species of Arbuscular mycorrhiza fungi on yield, yield components and water use efficiency (WUE of sesame (Sesamum indicum L. under different irrigation regimes, an experiment was conducted as split plot based on a randomized complete block design with three replications during two growing seasons 2009-2010 and 2010-2011 at the Agricultural Research Station, College of Agriculture, Ferdowsi University of Mashhad.. The experimental factors were three irrigation regimes include 2000, 3000 and

Historical effects of temperature and precipitation on California crop yields

Energy Technology Data Exchange (ETDEWEB)

Lobell, D.B. [Energy and Environment Directorate, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Cahill, K.N. [Interdisciplinary Graduate Program in Environment and Resources, Stanford University, Stanford, CA 94305 (United States); Field, C.B. [Department of Global Ecology, Carnegie Institution, Stanford, CA 94305 (United States)

2007-03-15

For the 1980-2003 period, we analyzed the relationship between crop yield and three climatic variables (minimum temperature, maximum temperature, and precipitation) for 12 major Californian crops: wine grapes, lettuce, almonds, strawberries, table grapes, hay, oranges, cotton, tomatoes, walnuts, avocados, and pistachios. The months and climatic variables of greatest importance to each crop were used to develop regressions relating yield to climatic conditions. For most crops, fairly simple equations using only 2-3 variables explained more than two-thirds of observed yield variance. The types of variables and months identified suggest that relatively poorly understood processes such as crop infection, pollination, and dormancy may be important mechanisms by which climate influences crop yield. Recent climatic trends have had mixed effects on crop yields, with orange and walnut yields aided, avocado yields hurt, and most crops little affected by recent climatic trends. Yield-climate relationships can provide a foundation for forecasting crop production within a year and for projecting the impact of future climate changes.

Measurement of the Exclusive Branching Fractions B{sup 0} {yields} {eta}K*{sup 0} and B{sup +} {yields} {eta}K*{sup +}

Energy Technology Data Exchange (ETDEWEB)

Aubert, B.

2004-02-12

The authors present the results of searches for B decays to the two charmless two-body final states B{sup 0} {yields} {eta}K*{sup 0} and B{sup +} {yields} {eta}K*{sup +}, based on 20.7 fb{sup -1} of data collected in 1999 and 2000 with the BABAR detector at PEP-II. They find the branching fractions {Beta}(B{sup 0} {yields} {eta}K*{sup 0}) = (19.8 {sub -5.6}{sup +6.5} {+-} 1.7) x 10{sup -6} and {Beta}(B{sup +} {yields} {eta}K*{sup +}) = (22.1 {sub -9.2}{sup +11.1} {+-} 3.3) x 10{sup -6}, where the first error quoted is the statistical and the second systematic.

Closing yield gaps in China by empowering smallholder farmers

Science.gov (United States)

Zhang, Weifeng; Cao, Guoxin; Li, Xiaolin; Zhang, Hongyan; Wang, Chong; Liu, Quanqing; Chen, Xinping; Cui, Zhenling; Shen, Jianbo; Jiang, Rongfeng; Mi, Guohua; Miao, Yuxin; Zhang, Fusuo; Dou, Zhengxia

2016-09-01

Sustainably feeding the world’s growing population is a challenge, and closing yield gaps (that is, differences between farmers’ yields and what are attainable for a given region) is a vital strategy to address this challenge. The magnitude of yield gaps is particularly large in developing countries where smallholder farming dominates the agricultural landscape. Many factors and constraints interact to limit yields, and progress in problem-solving to bring about changes at the ground level is rare. Here we present an innovative approach for enabling smallholders to achieve yield and economic gains sustainably via the Science and Technology Backyard (STB) platform. STB involves agricultural scientists living in villages among farmers, advancing participatory innovation and technology transfer, and garnering public and private support. We identified multifaceted yield-limiting factors involving agronomic, infrastructural, and socioeconomic conditions. When these limitations and farmers’ concerns were addressed, the farmers adopted recommended management practices, thereby improving production outcomes. In one region in China, the five-year average yield increased from 67.9% of the attainable level to 97.0% among 71 leading farmers, and from 62.8% to 79.6% countywide (93,074 households); this was accompanied by resource and economic benefits.

Evaluation of the Effect of Different Irrigation Levels of Drip Irrigation (Tape on Yield and Yield Components of Corn

Directory of Open Access Journals (Sweden)

mohammad karimi

2016-02-01

Full Text Available Introduction: One of the serious problems in the further development of maize cultivation is increasing irrigation efficiency. Using conventional irrigation causes a shortage of water resources to increase the acreage of the crop. With regard to the development of maize cultivation, agronomic and executable methods must be studied to reduce water consumption. Using drip irrigation system is most suitable for row crops. Hamedi et al. (2005 compared drip (tape and surface irrigation systems on yield of maize in different levels of water requirement and indicated that drip irrigation increases the amount of yield to 2015 kg/ha and water use efficiency to 3 time. Kohi et al. (2005 investigated the effects of deficit irrigation use of drip (tape irrigation on water use efficiency on maize in planting of one and two rows. The results showed that maximum water use efficiency related to crop density, water requirement and planting pattern 85000, 125% and two rows, respectively with 1.46 kg/m3. Jafari and Ashrafi (2011 studied the effects of irrigation levels, plant density and planting pattern in drip irrigation (tape on corn. The results showed that the amount of irrigation water and crop density on the level of 1% and their interactions and method of planting were significant at the 5 and 10% on water use efficiency, respectively. The yield was measured under different levels of irrigation, crop density and method of planting and the difference was significant on the level of 1%. Lamm et al. (1995 studied water requirement of maize in field with silt loam texture under sub drip irrigation and reported that water use reduced to 75%; but yield of maize remained at maximum amount of 12.5 t/ha. The objective of this study was to evaluate the drip (tape irrigation method for corn production practices in the Qazvin province in Iran. Materials and Methods: In this study, yield and yield components of corn (SC 704 were investigated under different levels of

Evaluation of Yield, Yield Components and Growth Indices of Safflower (Carthamus tinctorius L. in Conventional and Organic Farming Systems

Directory of Open Access Journals (Sweden)

Mahdieh Hajghani

2017-09-01

Full Text Available Introduction Application of organic fertilizers in sustainable agriculture systems improves yield sustainability of field crop. Safflower (Carthamus tinctorius L. is native to Middle East and belongs to the Asteraceae family. It is resistant to saline conditions, water stress, and can reach the deep-lying water of soil. The humic acid (HA mentioned as an environmentally friendly, organic matter with low levels of hormonal-like compounds is useful in improving agriculture production (Samavat and Malakuti 2006. The HA influence on plant growth depends on the source, concentration and molecular weight of the substance. Vermicompost is produced by earthworms, mainly Eisenia foetida, it has higher levels of available nutrients compared to the original materials of composts produced by other methods. Recent evidences suggest that using different amounts of vermicompost increased vegetative traits and concentration of minerals in sunflower. However, there has been little discussion about organic farming of safflower. The main objectives of the present study were to determine the effect of organic treatments on yield, yield components, and growth indices of safflower and to compare it with conventional agriculture. Materials and methods This research was conducted in Agricultural and Natural Resources Research Station in Kerman, Iran during 2012–2013. It was carried out in a randomized complete block (RCB design and had three replications. The current research has been performed to investigate the effects of two different sources of organic fertilizer on spring safflower. Four levels of vermicompost (V: 0, 3, 6 and 9 t ha-1 were considered in the main plots. Liquid humic acid at four different concentrations (HA: 0, 1000, 2000 and 3000 ppm were examined and kept in the subplots. Humic acid as a foliar treatment on leaf surface was applied twice at the beginning of stem elongation and at flowering times. In this study, aimed to compare organic farming

High-yield pulping effluent treatment technologies

International Nuclear Information System (INIS)

Su, W.X.; Hsieh, J.S.

1993-03-01

The objective of this report is to examine the high-yield (mechanical) pulp processes with respect to environmental issues affected by the discharge of their waste streams. Various statistics are given that support the view that high-yield pulping processes will have major growth in the US regions where pulp mills are located, and sites for projects in the development phase are indicated. Conventional and innovative effluent-treatment technologies applicable to these processes are reviewed. The different types of mechanical pulping or high-yield processes are explained, and the chemical additives are discussed. The important relationship between pulp yield and measure of BOD in the effluent is graphically presented. Effluent contaminants are identified, along with other important characteristics of the streams. Current and proposed environmental limitations specifically related to mechanical pulp production are reviewed. Conventional and innovative effluent-treatment technologies are discussed, along with their principle applications, uses, advantages, and disadvantages. Sludge management and disposal techniques become an intimate part of the treatment of waste streams. The conclusion is made that conventional technologies can successfully treat effluent streams under current waste-water discharge limitations, but these systems may not be adequate when stricter standards are imposed. At present, the most important issue in the treatment of pulp-mill waste is the management and disposal of the resultant sludge

Effect of Drought Stress at Different Growth Stages on Yield and Yield Components of Six Rice (Oryza sativa L. Genotypes

Directory of Open Access Journals (Sweden)

Sharifunnessa Moonmoon

2017-12-01

Full Text Available Drought stress affects plant growth and development and ultimately, reduced grain yield of rice. But stress at different growth stages may respond differently which is still unclear. Therefore, a pot experiment was carried out with six rice genotypes to determine the critical growth stage where drought stress effect on yield reduction and to find stress tolerance mechanism in rice genotypes. Drought stress (control i.e. no stress and 40% field capacity, FC was imposed on Binadhan-13, Kalizira, BRRI dhan34, Ukunimodhu, RM-100-16 and NERICA mutant rice genotypes at maximum tillering, panicle initiation and grain filling stages and discontinued when the specific stage was over. The experiment was laid out in a complete randomized design with three replications. Drought stress affected number of effective tiller hill-1, number of spikelets panicle-1, filled grains hill-1, 1000-grain weight and grain yield. Binadhan-13 produced the highest grain yield and the lowest sterility under drought stress at grain filling stage. Percentage of spikelet sterility increased under drought stress (40% FC especially at the panicle initiation stage resulting low grain yield. Among the tested genotypes Binadhan-13 performed well by reducing spikelet sterility under drought stress condition. For 1000-grain weight and grain yield, grain filling stage was found more crucial. From the current research, drought tolerance mechanism was found in genotypes Binadhan-13 and NERICA mutant. [Fundam Appl Agric 2017; 2(3.000: 285-289

Willow yield is highly dependent on clone and site

DEFF Research Database (Denmark)

Ugilt Larsen, Søren; Jørgensen, Uffe; Lærke, Poul Erik

2014-01-01

Use of high-yielding genotypes is one of the means to achieve high yield and profitability in willow (Salix spp.) short rotation coppice. This study investigated the performance of eight willow clones (Inger, Klara, Linnea, Resolution, Stina, Terra Nova, Tora, Tordis) on five Danish sites......, differing considerably in soil type, climatic conditions and management. Compared to the best clone, the yield was up to 36 % lower for other clones across sites and up to 51 % lower within sites. Tordis was superior to other clones with dry matter yields between 5.2 and 10.2 Mg ha−1 year−1 during the first...... 3-year harvest rotation, and it consistently ranked as the highest yielding clone on four of the five sites and not significantly lower than the highest yielding clone on the fifth site. The ranking of the other clones was more dependent on site with significant interaction between clone and site...

X-ray yields of superdeformed states in 193Hg

International Nuclear Information System (INIS)

Cullen, D.M.; Lee, I.Y.; Baktash, C.

1993-01-01

The K α =x-ray yields associated with the superdeformed and normal-deformed bands in 193 Hg have been measured. The results indicate an excess yield of K α -x rays in coincidence with the superdeformed cascade relative to that in coincidence with the normal-deformed cascade. The internal conversion of known transitions along the superdeformed cascade cannot account for the observed K α -x ray yield. It is likely that this excess x-ray yield is associated with low energy M1 transitions competing with the low-spin superdeformed E2 transitions. These M1 γ rays are expected to connect the two superdeformed bands which are observed in coincidence with each other. Calculations based on the measured γ-ray intensities indicate that within the experimental uncertainties the excess K α yield can be entirely accounted for by interband-M1 transitions. X-ray yields from the recent 193 Hg EUROGAM experiment will also be discussed

LET dependence of scintillation yields in liquid argon

Energy Technology Data Exchange (ETDEWEB)

Doke, Tadayoshi; Hitachi, Akira; Kikuchi, Jun; Crawford, H J; Lindstrom, P J; Masuda, Kimiaki; Shibamura, Eido; Takahashi, Tan

1988-06-01

Scintillation yields (scintillation intensity per unit absorbed energy) in liquid argon for ionizing particles are reviewed as a function of LET for the particles. The maximum scintillation yield, which is obtained for relativistic heavy ions from Ne to La, is about 1.2 times larger than that for gamma rays in NaI(Tl) crystal. In the low LET region, the scintillation yields for relativistic electrons, protons and He ions are 10-20% lower than the maximum yield. This tendency can be explained by taking into account the existence of the electrons which have escaped from their parent ions. In the high LET region, a quenching effect due to high ionization density is observed for alpha particles, fission fragments and relativistic Au ions.

Effect of Drought Stress onYield and Yield Components of Sesame cultivars under Kerman conditions (Sesamum indicum L.

Directory of Open Access Journals (Sweden)

S Farahbakhsh

2015-04-01

Full Text Available To investigate effects of drought stress on yield and yield components of sesame in Kerman region a split-plot experiment based onn compelet randomised block design with three replications was carried out in 1388. Irrigation levels (Normal irrigation in all growth stages, witholding water after 50% flowering, witholding water after 50% pod setting and differen t sesame landraces (Jiroft, Shiraz, Ardestan, Dezful, Shahr babak, Gorgan, Sirjan, Markazi, Birjand and Orzueieh were considered as main plots and sub-plots respectively. Plant height, the biggest pod length, noumber of grain per pod, noumber of pod per plant, grain weight per plant, thousand grain weight and grain yield were the measured traits. Results showed all the measured traits were significantly affected by the irrigation treatments. The effects of different landraces on all traits except noumber of grain per plant were significant. Irrigation × landraces interaction affected all measured traits except the biggest pod length significantly. The highest grain yield was recorde for Markezi landrace (845.2 kg –ha under normal irrigation and the lowest one was obtained from Jiroft landrace (104.8 kg –ha with witholding irrigation after 50% flowering.

Fine Mapping of qroot-yield-1.06, a QTL for Root, Plant Vigor and Yield in Maize

OpenAIRE

Martinez Ascanio, Ana Karine

2015-01-01

Root-yield-1.06 is a major QTL affecting root system architecture (RSA) and other agronomic traits in maize. The effect of this QTL has been evaluated with the development of near isogenic lines (NILs) differing at the QTL position. The objective of this study was to fine map qroot-yield-1.06 by marker-assisted searching for chromosome recombinants in the QTL interval and concurrent root phenotyping in both controlled and field conditions, through successive generations. Complementary approac...

The effect of sowing date and plant density on yield and yield components of safflower (Carthamus tinctorious L. in Rokh plateau .

Directory of Open Access Journals (Sweden)

seyd fazel fazeli kakhaki

2009-06-01

Full Text Available To investigate the effect of sowing date and plant density on yield and yield components of safflower ( Carthamus tinctorious as well as evaluating the possibility of the second sowing of the plant in Torbat Heidariyeh , a field experiment was conducted in Rokh, Cold Season Cereal Research Station 2005 . The experiment was conducted in split plot arrangement in complete randomized block design with four replications . Main plots were sowing date in five levels including 9 April, 10 May, 31 May, 20 June, 11 July and sub plots were plant density in three levels including 300000, 400000, 500000 plants per hectar. Some charactristics such as the number of capitulum per square meter, seed number in capitulum, seed weight, harvest index and seed yeild was evaluated.The highest seed yield was obtained in first sowing date in 3347 kg/ha and a delay in sowing date resulted a decrease in yield. The cold weather in (05/11/2005 caused flower fertility not accured, consequently, sowing was not successful . Results showed that the effect of sowing date on yield depends on the number of capitulum per unit area and the number of grains per capitulum. These two characteristics in th first sowing date in respect of the other dates were higher. The effect of density on yield was significant resulted on yield increase due to capitulum increase in unit area. As a result, the first sowing date with the highest density is recommended. However, The third and fourth sowing date can be considered as the second planting in a sequeational cropping system .

Effect Of Cowpea Planting Density On Growth, Yield And ...

African Journals Online (AJOL)

Effect Of Cowpea Planting Density On Growth, Yield And Productivity Of Component Crops In Cowpea/Cassava Intercropping System. ... Similarly, fresh root yield (t/ha) of cassava was influenced by cropping system and population density in 2005/2006, but not in 2004/2005 cropping season. Cassava tuber yield was ...

ENDF/B yield evaluation for 1992: Methods and content

International Nuclear Information System (INIS)

England, T.R.; Rider, B.F.

1992-01-01

The basic evaluation process, completed in May 1992, for 60 independent, plus corresponding cumulative yield sets is described thirty-six fissioning nuclides at one-or-more neutron fission energies or spontaneous fission are included. The resulting recommended yields include approximately 1200 nuclides per set; these will be slightly extended to encompass all nuclides in the ENDF/B-VI decay files and issued as the second release of ENDF/B-VI yields. All current yield sets in ENDF/B-VI have been reevaluated using ∼3000 new measurements and model parameters for distribution along mass chains. Compiled measurements through 1992 will be included in the documentation of the recommended yields. This paper can only summarize the primary features of the evaluations

Bioinspiration and Biomimicry: Possibilities for Cotton Byproducts

Science.gov (United States)

The byproducts from cotton gins have commonly been referred to as cotton gin trash or cotton gin waste primarily because the lint and seed were the main focus of the operation and the byproducts were a financial liability that did not have a consistent market. Even though the byproducts were called ...

Effect of water pressure on absorbency of hydroentangled greige cotton nonwoven fabrics

Science.gov (United States)

A studied has been conducted to determine the effect of water pressure in a commercial-grade Fleissner MiniJet hydroentanglement system on the absorbency of greige (non-bleached) cotton lint-based nonwoven fabric. The study has shown that a water pressure of 125 Bar or higher on only two high-pressu...

YIELD STABILITY OF NEW HYBRID RICE ACROSS LOCATIONS

Directory of Open Access Journals (Sweden)

Satoto

2016-02-01

Full Text Available The adaptation of hybrid rice varieties mostly are in specific location and season, but there are some of the varieties have a wide adaptation then adopted by the farmer in the large area. Replicated yield trials were conducted to study the stability of hybrid rice yield and identify the best location to optimize their yield per ha. The trials were conducted in three location such as Sukamandi, Salatiga and Malang during two seasons in 2011. Data across location and season were analazed by using AMMI and Eberhart Russel methods. The AMMI analysis showed that the IR79156A/PK88 was adaptable to favorable environments but unstable. This hybrid is always performing well and produce the higher yield compare to check variety. Some of other hybrids were good only in specific location, i.e. IR62829A/BP2280-1E-12-22 and IR58029A/BP2280-1E-12-22. Those hybrids produced higher yield in Salatiga and Malang, respectively. Seem to AMMI analysis, the result of Eberhart and Russell method also showed that IR79156A/PK81 was the best hybrid with regression slope (b around 1 with the yield average higher than average of all hybrids. It indicated that this hybrid has a wide adaptation and probably can be cultivated in the wider ecosystem.

Enhancing Jatropha curcas (Linnaeus) Cultivation and Seed Yield ...

African Journals Online (AJOL)

Enhancing Jatropha curcas (Linnaeus) Cultivation and Seed Yield among ... Journal of Agricultural Research and Development ... Jatropha curcas yields substantial quantity of seed oil and is growing in importance as a source of biodiesel.

Methane Yield Database: Online infrastructure and bioresource for methane yield data and related metadata.

Science.gov (United States)

Murovec, Boštjan; Kolbl, Sabina; Stres, Blaž

2015-01-01

The aim of this study was to develop and validate a community supported online infrastructure and bioresource for methane yield data and accompanying metadata collected from published literature. In total, 1164 entries described by 15,749 data points were assembled. Analysis of data collection showed little congruence in reporting of methodological approaches. The largest identifiable source of variation in reported methane yields was represented by authorship (i.e. substrate batches within particular substrate class) within which experimental scales (volumes (0.02-5l), incubation temperature (34-40 °C) and % VS of substrate played an important role (p 63%). This calls for reconsideration of accepted approaches to reporting data in currently published literature to increase capacity to service industrial decision making to a greater extent. Copyright © 2015 Elsevier Ltd. All rights reserved.

Determination of fission gas yields from isotope ratios

DEFF Research Database (Denmark)

Mogensen, Mogens Bjerg

1983-01-01

This paper describes a method of calculating the actual fission yield of Kr and Xe in nuclear fuel including the effect of neutron capture reactions and decay. The bases for this calculation are the cumulative yields (ref. 1) of Kr and Xe isotopes (or pairs of isotopes) which are unaffected...... by neutron capture reactions, and measured Kr and Xe isotope ratios. Also the burnup contribution from the different fissile heavy isotopes must be known in order to get accurate fission gas yields....

Ternary particle yields in 249Cf(nth,f)

Science.gov (United States)

Tsekhanovich, I.; Büyükmumcu, Z.; Davi, M.; Denschlag, H. O.; Gönnenwein, F.; Boulyga, S. F.

2003-03-01

An experiment measuring ternary particle yields in 249Cf(nth,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37Si and 37S; their possible origin is discussed.

Evaluation of Relationship Between Auxin and Cytokinine Hormones on Yield and Yield Components of Maize under Drought Stress Condition

Directory of Open Access Journals (Sweden)

A Mahrokh

2016-10-01

Full Text Available Introduction Drought is one of the major environmental conditions that adversely affects plant growth and crop yield. In the face of a global scarcity of water resources, water stress has already become a primary factor in limiting crop production worldwide. Drought is the major restriction in maize production. The plant growth reduction under drought stress conditions could be an outcome of altered hormonal balance and hence the exogenous application of growth regulators under stress conditions could be the possible means for reversing the effects of abiotic stress. Phytohormones such as auxine and cytokinine are known to be involved in the regulation of plant response to the adverse effects of stress conditions. Previous studies have shown that endogenous hormones are essential regulators for translocation and partitioning of photoassimilates for grain filling in cereal crops, and therefore could be involved in the regulation of grain weight and yield. Materials and Methods The experiment was carried out in three separately environments included non-drought stress environment (irrigation after soil moisture reached to 75% field capacity, drought stress in vegetative stage (irrigation after soil moisture reached to 50% field capacity in V4 to tasseling stage, but irrigation after soil moisture reached to 75% field capacity in pollination to physiological maturity stage and drought stress in reproductive stage (irrigation after soil moisture reached to 75% field capacity in V4 to tasseling stage and irrigation after soil moisture reached to 50% field capacity in pollination to physiological maturity stage. Cytokinin hormone in three levels (control, spraying in V5 –V6 and V8-V10 stages and auxin hormone in three levels (control, spraying in silk emergence stage and 15 days after that were laid out as a factorial design based on randomized complete block with three replications in each environment at Seed and Plant Improvement Institute (SPII

SLIFER measurement for explosive yield

International Nuclear Information System (INIS)

Bass, R.C.; Benjamin, B.C.; Miller, H.M.; Breding, D.R.

1976-04-01

This report describes the shorted location indicator by frequency of electrical resonance (SLIFER) system used at Sandia Laboratories for determination of explosive yield of under ground nuclear tests

Effect of Limited Drip Irrigation Regime on Yield and Yield Components of Sesame under Mediterranean Conditions

Directory of Open Access Journals (Sweden)

Panayiota PAPASTYLIANOU

2017-05-01

Full Text Available Sesame is one of the most important oilseed crops in the world. Irrigation is of great importance to sesame production due to its positive effect on growth parameters. Although sesame has good drought tolerance compared with many other crops, it is particularly susceptible to drought damage during the seedling, flowering and seed filling stages and this can lead to yield loss. The aim of this study was to determine the response of sesame landraces to different irrigation applications during the 2015 growing season. The experiment was set up as a split plot design with three replicates, four main plots (irrigation treatments, designated as 100%, 75% 50% and 0 of the daily crop evapotranspiration and two sub-plots (sesame landraces, Limnos and Evros. Different characteristics such as plant height, number of seeds per capsule, and number of capsules per plant, seed yield, 1000-seed weight and % capsules without seeds, were recorded. The results indicated that all traits except 1000-seed weight were significantly affected by irrigation regimes. Plant height, shattering losses and number of capsules per plant decreased with increasing water shortage. Seed yield and number of seeds per capsule were less affected by irrigation level and showed higher values in the 50% of the daily crop evapotranspiration treatment. Limnos produced higher seed yield and number of seeds per capsule under all irrigation regimes. Evros showed higher plant height and shattering losses than Limnos. The results of this study suggest that sesame landraces can use water efficiently, are locally adapted and associated with traditional farming systems.

Growth and yield responses of Sphenostylis stenocarpa (Hochst ex ...

African Journals Online (AJOL)

STORAGESEVER

2009-02-18

Feb 18, 2009 ... The effects of varying levels (0, 110, 220, 330, 440, and 550 kg P/ha) of phosphate application on some growth and yield parameters of African yam bean were studied. Plant dry weight ... of the control treatment, (12.79 g). Grain yield was ... Key word: Fertilizer, phosphate, Sphenostylis stenocarpa, yield.

Sensitivity of CERES-Maize yield simulation to the selected weather data

International Nuclear Information System (INIS)

Zalud, Z.; Stastna, M.

2000-01-01

Sensitivity analysis of selected weather data runs after successful parametrization and validation of the CERES-Maize simulation model. Estimation of the potential yield has been carried out during the long term experiment (1980-1997) as well as the estimation of influence of meteorological parameters on the simulation results for the water-limited yield. 10 % under and over stimulation of global radiation and precipitation as well as increasing and decreasing temperature by 1 deg C on simulated potential and water-limited yield have been done. In most of the years, air temperature underestimation resulted in a higher simulated grain yield and overstimulation shown a lower yield for water limited level. Overestimation of precipitation during wet days in growing period of the maize leads to an increase of amount of water available for the plant and to increase the yield. Underestimation of global radiation by 10 % resulted in a decline in simulated grain yield from -8.8 to -9.9 %. The overestimation caused increase of the yield from 7.8 to 10 %. Overestimation by 10 % resulted in a slight underestimation of the yield in low yielding years and underestimation of global radiation by 10 % in overestimation of the yield. The effect was opposite in high yielding years

EMPIRICALLY DERIVED INTEGRATED STELLAR YIELDS OF Fe-PEAK ELEMENTS

International Nuclear Information System (INIS)

Henry, R. B. C.; Cowan, John J.; Sobeck, Jennifer

2010-01-01

We present here the initial results of a new study of massive star yields of Fe-peak elements. We have compiled from the literature a database of carefully determined solar neighborhood stellar abundances of seven iron-peak elements, Ti, V, Cr, Mn, Fe, Co, and Ni, and then plotted [X/Fe] versus [Fe/H] to study the trends as functions of metallicity. Chemical evolution models were then employed to force a fit to the observed trends by adjusting the input massive star metallicity-sensitive yields of Kobayashi et al. Our results suggest that yields of Ti, V, and Co are generally larger as well as anticorrelated with metallicity, in contrast to the Kobayashi et al. predictions. We also find the yields of Cr and Mn to be generally smaller and directly correlated with metallicity compared to the theoretical results. Our results for Ni are consistent with theory, although our model suggests that all Ni yields should be scaled up slightly. The outcome of this exercise is the computation of a set of integrated yields, i.e., stellar yields weighted by a slightly flattened time-independent Salpeter initial mass function and integrated over stellar mass, for each of the above elements at several metallicity points spanned by the broad range of observations. These results are designed to be used as empirical constraints on future iron-peak yield predictions by stellar evolution modelers. Special attention is paid to the interesting behavior of [Cr/Co] with metallicity-these two elements have opposite slopes-as well as the indirect correlation of [Ti/Fe] with [Fe/H]. These particular trends, as well as those exhibited by the inferred integrated yields of all iron-peak elements with metallicity, are discussed in terms of both supernova nucleosynthesis and atomic physics.

Computer optimization of cutting yield from multiple ripped boards

Science.gov (United States)

A.R. Stern; K.A. McDonald

1978-01-01

RIPYLD is a computer program that optimizes the cutting yield from multiple-ripped boards. Decisions are based on automatically collected defect information, cutting bill requirements, and sawing variables. The yield of clear cuttings from a board is calculated for every possible permutation of specified rip widths and both the maximum and minimum percent yield...

Heritability studies of yield and yield associated traits in bread wheat

International Nuclear Information System (INIS)

Laghari, K.A.; Sial, M.A.; Arain, M.A.; Mirbahar, A.A.; Pirzada, A.; Mancrio, S.M.; Dahot, M.U.

2010-01-01

Heritability studies provide valid information about the traits that are transmitted from parents to offspring and also to the successive generations. Such studies help plant breeders to predict a successful cross with high heritability transmission to the progeny and thus are useful in the incorporation of characters into the offspring. Heritability study was conducted in F5 segregating generation of a cross between HT5 (female) and HT 37 (male) of bread wheat. The genetic parameters calculated were genetic variance (Vg,), environmental variance (Ve) and heritability percentage in broad sense (h2%), genetic advance (GA) and heritability coefficient (H). The highest heritability was observed for spike length (79.3%), number of grains per spike (54.5%) and main spike yield (69.5%) associated with high genetic advance (2.8, 22.8 and 1.5 respectively). Moderate to high heritability were recorded for peduncle length (48.75%) and number of grains per spikelet (47.2%) which associated with high genetic advance (2.3 and 0.68 respectively). However awn length and plant height had shown acceptable heritability values. The present finding suggests that most of the yield associated traits have been successfully transmitted. The information generated will be helpful for better understanding and selection of suitable, desirable material especially in advance generations. (author)

Evaluation of Yield and Yield Components of Oilseed Rape in the Wheat-Oilseed Rape Strip Intercropping Influenced by Chemical and Biological Fertilizers

Directory of Open Access Journals (Sweden)

R Amirmardfar

2015-01-01

Full Text Available To evaluate the effects of wheat (Triticum aestivum and oilseed rape (Brassica napus strip intercropping on yield components, seed and biological yields of oilseed rape, field experiments were carried out as factorial based on randomized complete block design with three replications at Research Farm of Tabriz University, Tabriz, Iran during 2010-2012 cropping seasons. The first factor consisted of four types of wheat and oilseed rape cropping system, sole crop of oilseed rape (A1,: strip intercropping with 8:3 (A2, 12:4 (A3 and 16:5 (A4 of wheat and oilseed rape rows, respectively and the other factor consisted of two fertilizer levels, B1: 100% chemical fertilizers (urea and triple superphosphate and B2: 50% chemical fertilizers + biofertilizers (Nitrazhin and Barvar2. The results showed that strip intercropping of wheat- oilseed rape resulted in significant increase in yield components, seed yield per occupied unit area and biological yield per occupied unit area of oilseed rape as compared with mono-cropping. The number of silique per plant in intercropping systems was significantly higher than that of mono-cropping. The highest seed yield was obtained in the 16:5 rows of wheat-oilseed rape with 343.76 g.m-2 and the lowest mean was observed in mono-cropping of oilseed rape with 260.21 g.m-2. Biological yield per occupied unit area and seed yield per intercropped unit area in B1 were significantly greater than that of B2, but this treatment had no significant effect on the other traits. Because, B1 and B2 had no significant difference in seed yield per occupied unit area and due to the importance of reduction in chemical fertilizers consumption and food and environmental health care, strip intercropping of wheat-oilseed rape under 50% chemical fertilizers + biofertilizers can be recommended as a suitable cultural method.

A preliminary yield trial of some soybean mutant lines

International Nuclear Information System (INIS)

Ratma, Rivaie

1985-01-01

A preliminary yield trial of some soybean mutant lines, derived from irradiated Orba variety with dose of 0.40 kGy, were carried out during the wet and dry season in 1979-1982 in Muara and Citayam, Bogor. The result obtained showed that yield potential of mutant lines no. M6/40/10 was higher than that of the control in dry season in 1979 as well as in the wet season of 1979/80 in Muara. Whereas, the yield potential of the mutant lines no. M6/40/8 and no. M6/40/14 were higher than that of the control only in the wet season. The yield potential of semi dwarf mutant lines no. M6/40/68 was highly significant compared to that of the control in dry season in Muara and the wet season in 1981/82 in Citayam. Whereas, the yield potential of the mutant lines no. M6/40/69 was higher yield compared to that of the control in dry season in 1981 in Muara. (author). 10 refs

Effect of Nutritional Management on Yield and Yield Components of Roselle (Hibiscus sabdariffa as a Medicinal Plant in Mashhad Condition

Directory of Open Access Journals (Sweden)

P Rezvani Moghaddam

2018-02-01

Full Text Available Introduction Roselle (Hibiscus sabdariffa is an annual plant with a height of about 64 to 429 cm belongs to Malvaceae family. Roselle is self-pollinated and sensitive to cold. Sepals of Roselle are used in food and pharmaceutical industries. It has been reported that Roselle is not native to Iran but it is cultivated extensively in Sistan and Baluchistan province, Iran. In order to achieve high quality and quantity yield of Roselle sepal it is necessary to improve nutritional systems of plant. Proper management of soil fertility and plant nutrition can preserve environment, improve biodiversity and also increase inputs efficiency. Results showed that use of nutritional resources will improve plant growth. Organic fertilizers such as compost can improve soil fertility as an important source of food that increase yield of plants. Nabila and Aly (2002 observed that use of hen and cow manure increased plant height, number of lateral branches, numbers of fruit and sepal yield of Roselle. Each plant species has the maximum potential in favorable conditions. Therefore, evaluation the effect of climatic and agronomic factors and nutritional management for plants is essential. This experiment was conducted to evaluate the yield and yield components of Roselle in response to use of single and combined nutritional resources. Materials and Methods In order to study the effects of single and combined organic, biological and chemical fertilizers on yield and yield components of Roselle (Hibiscus sabdariffa, a field experiment was conducted with 12 treatments based on a Randomized Complete Block Design with three replications at Research Station, Faculty of Agriculture, Ferdowsi University of Mashhad, Iran, in 2013-2014. Treatments included: 1- mycorrhiza (Glomus intraradices, 2- cow manure, 3- chemical fertilizer, 4- vermicompost, 5- chemical fertilizer + cow manure, 6- chemical fertilizer + vermicompost, 7- chemical fertilizer + mycorrhiza, 8- cow manure

Electromagnetic corrections in {eta}{yields}3{pi} decays

Energy Technology Data Exchange (ETDEWEB)

Ditsche, Christoph; Kubis, Bastian [Universitaet Bonn, Helmholtz-Institut fuer Strahlen- und Kernphysik (Theorie) and Bethe Center for Theoretical Physics, Bonn (Germany); Meissner, Ulf G. [Universitaet Bonn, Helmholtz-Institut fuer Strahlen- und Kernphysik (Theorie) and Bethe Center for Theoretical Physics, Bonn (Germany); Forschungszentrum Juelich, Institut fuer Kernphysik (Theorie), Institute for Advanced Simulations, and Juelich Center for Hadron Physics, Juelich (Germany)

2009-03-15

We re-evaluate the electromagnetic corrections to {eta}{yields}3{pi} decays at next-to-leading order in the chiral expansion, arguing that effects of order e{sup 2}(m{sub u}-m{sub d}) disregarded so far are not negligible compared to other contributions of order e {sup 2} times a light-quark mass. Despite the appearance of the Coulomb pole in {eta}{yields}{pi}{sup +}{pi}{sup -}{pi}{sup 0} and cusps in {eta}{yields}3{pi}{sup 0}, the overall corrections remain small. (orig.)

Ternary particle yields in 249Cf(nth,f)

International Nuclear Information System (INIS)

Tsekhanovich, I.; Bueyuekmumcu, Z.; Davi, M.; Denschlag, H.O.; Goennenwein, F.; Boulyga, S.F.

2003-01-01

An experiment measuring ternary particle yields in 249 Cf(n th ,f) was carried out at the high flux reactor of the Institut Laue-Langevin using the Lohengrin recoil mass separator. Parameters of energy distributions were determined for 27 ternary particles up to 30 Mg and their yields were calculated. The yields of 17 further ternary particles were estimated on the basis of the systematics developed. The heaviest particles observed in the experiment are 37 Si and 37 S; their possible origin is discussed

Yield improvement of Kenyan sesame varieties

International Nuclear Information System (INIS)

Ayiecho, P.O.; Nyabundi, J.O.

2001-01-01

In an effort to improve the yield of Kenyan sesame cultivars the seeds of three cultivars, SPS SIK6, SIK 096 and SPS SIK 50/1 were subjected to 300Gy, 400Gy and 600Gy of gamma rays. A first batch of seeds were subjected to these treatments in March 1994 (Experiment I) while the second batch was treated in March 1995 (Experiment II). The M 1 , M 2 , M 3 and M 4 generations of experiment I and M 1 generation of Experiment II were raised at the University of Nairobi Dryland Research Field Station, Kibwezi from 1994 to 1996. The M 6 and M 7 generations of Experiment I and M 2 of Experiment II were raised at Siaya Farmer's Training Centre in 1997. The effects of radiation in M 1 generation were expressed in reduced and delayed seedling emergence, reduced plant height, sectorial deformed plants, delayed flowering and extremely low yield. There was increased variation in M 2 for most evaluated traits. Plants in M 2 and subsequent generations were scored for a number of yield related morphological traits and days to flowering. Selection was done in the early generations for increased capsule number and earliness. As a result of selection, a total of 88 lines from M 4 generation were used to derive M 5 generation. Further selection in M 6 generation lead to 35 lines being retained for preliminary yield trials in M 7 generations. (author)

Sorghum stem yield and soluble carbohydrates under different ...

African Journals Online (AJOL)

STORAGESEVER

2008-11-19

Nov 19, 2008 ... Key words: Sweet sorghum, grain sorghum, salinity, stem yield, ... The effect of salinity on the stem yield and sucrose was .... growth and polyamine metabolism in two citrus rootstocks with ... Growth and osmoregulation in two.

Yield and Adaptability Evaluation of Newly Introduced Tomato ...

African Journals Online (AJOL)

High yield is a major ambition to tomato plant breeders and farmers. The purpose of the ... Tabora Region on the growth and yield of newly introduced tomato varieties. The tested ..... (1985). Evaluation of some American tomatocultivars grown.

Effects of different irrigation programs on yield and quality ...

African Journals Online (AJOL)

Evapotranspiration (ET) values varied from 93.1 to 466.3 mm for the treatments. The highest yield was obtained from the S3 and S4 treatments. A significant polynomial correlation was obtained between the yield and irrigation water, and between the yield and ET (P < 0.01). This indicated that when irrigation water and ET ...

Understanding the weather signal in national crop-yield variability

Science.gov (United States)

Frieler, Katja; Schauberger, Bernhard; Arneth, Almut; Balkovič, Juraj; Chryssanthacopoulos, James; Deryng, Delphine; Elliott, Joshua; Folberth, Christian; Khabarov, Nikolay; Müller, Christoph; Olin, Stefan; Pugh, Thomas A. M.; Schaphoff, Sibyll; Schewe, Jacob; Schmid, Erwin; Warszawski, Lila; Levermann, Anders

2017-06-01

Year-to-year variations in crop yields can have major impacts on the livelihoods of subsistence farmers and may trigger significant global price fluctuations, with severe consequences for people in developing countries. Fluctuations can be induced by weather conditions, management decisions, weeds, diseases, and pests. Although an explicit quantification and deeper understanding of weather-induced crop-yield variability is essential for adaptation strategies, so far it has only been addressed by empirical models. Here, we provide conservative estimates of the fraction of reported national yield variabilities that can be attributed to weather by state-of-the-art, process-based crop model simulations. We find that observed weather variations can explain more than 50% of the variability in wheat yields in Australia, Canada, Spain, Hungary, and Romania. For maize, weather sensitivities exceed 50% in seven countries, including the United States. The explained variance exceeds 50% for rice in Japan and South Korea and for soy in Argentina. Avoiding water stress by simulating yields assuming full irrigation shows that water limitation is a major driver of the observed variations in most of these countries. Identifying the mechanisms leading to crop-yield fluctuations is not only fundamental for dampening fluctuations, but is also important in the context of the debate on the attribution of loss and damage to climate change. Since process-based crop models not only account for weather influences on crop yields, but also provide options to represent human-management measures, they could become essential tools for differentiating these drivers, and for exploring options to reduce future yield fluctuations.

Effects of Vermi-compost Fertilizer Application and Foliar Spraying on Yield and Yield Component of Isabgol (Plantago ovate L. Medicinal Plant

Directory of Open Access Journals (Sweden)

Asghar Rahimi

2017-12-01

Full Text Available Introduction Vermi-compost is the ability of some species of earthworms to consume and break down a wide range of organic residues such as sewage sludge, animal wastes, crop residues and industrial refuse. Vermi-composts are usually more stable than their parent materials with increased availability of nutrients and improved physicochemical and microbiological properties. Aerial compost tea contains high populations of live microorganism consisting of rhizobactria, trichoderma and pseudomonas species which increase the growth and yield of the plant. Acid humic is the main humic substance and the important ingredient of soil organic matter (humus which causes increase of yield and quality of crop. The aim of this research is evaluating the effect of vermi-compost and foliar application of compost tea and acid humic on yield, yield component and mucilage content of isabgol. Vermiwash as the extract of vermi-compost is liquid organic fertilizer obtained from unit of vermiculture and vermi-compost as drainage. It is used as a foliar spraying on the leaf. Vermiwash stimulate and increase the yield of crop products and foliar application of vermiwash can be caused of plant resistance to different factors and can prevent leaf necrosis. Material and Methods In order to study the effect of vermi-compost and foliar application of tea compost and acid humic on growth indices of isabgol (Plantago ovata, an experiment was conducted as a factorial based on complete randomized design with three replications in agricultural research farm at Vali-e-Asr University of Rafsanjan. Treatments were included application of vermi-compost (0 (control, 4, 8, 12 and 16 t.ha-1 and 3 levels of foliar application (distilled water as control, acid humic and compost tea. Samples for evaluating of yield, yield components and mucilage content were taken from 1 m2 area of each treatment. Tea compost solution prepared using mix of vermi-compost, acid humic, yeast and alga extract

Persistency of milk yield in Indonesian Holstein cows

Science.gov (United States)

Widyas, N.; Putra, F. Y.; Nugroho, T.; Pramono, A.; Susilowati, A.; Sutarno; Prastowo, S.

2018-03-01

Milk yield is an important trait in dairy industry; thus, information regarding this phenotype is essential to measure the productivity of a farm. Total milk yield in one lactation period was often predicted using information from samples collected within certain time intervals. The rate of change of milk production between two-time intervals is defined as persistency. This article aims to estimate the persistency of milk yield between lactation 1, 2 and 3 in Indonesian Friesian Holstein (IFH) cows. Data was collected from Limpakuwus stable, Baturraden Dairy Cattle Breeding Centre, Central Java Indonesia. Records were obtained from cows which started lactating on 2013 until the end of third lactation around the beginning of 2016. Milk yield from the first (L1), second (L2) and third (L3) lactations of 21 cows were recorded in kilograms. Samples were collected in 30 days basis interval started from the 10th day of lactation up to the 10th month. In this population, the cows first calving was around February – April 2013; while the second and third calving occurred all over the relevant year. The mean of milk yield for L1, L2 and L3 were 17.77±3.70, 16.09±5.17 and 13.73±4.02 Kg respectively. The peak of milk yields was achieved at the second month of the lactation for L1, L2 and L3. The persistency from the second to the tenth test days were 97, 93 and 94% for L1, L2 and L3, respectively. Milk yield persistency is representing ability of cow in maintain milk production after peak during lactation period. The more persistent shows better performance of dairy cattle as well as farm management. For that, persistency value could be used as valuable information in evaluating the management in Indonesian dairy farms.

Closing Yield Gaps: How Sustainable Can We Be?

Directory of Open Access Journals (Sweden)

Prajal Pradhan

Full Text Available Global food production needs to be increased by 60-110% between 2005 and 2050 to meet growing food and feed demand. Intensification and/or expansion of agriculture are the two main options available to meet the growing crop demands. Land conversion to expand cultivated land increases GHG emissions and impacts biodiversity and ecosystem services. Closing yield gaps to attain potential yields may be a viable option to increase the global crop production. Traditional methods of agricultural intensification often have negative externalities. Therefore, there is a need to explore location-specific methods of sustainable agricultural intensification. We identified regions where the achievement of potential crop calorie production on currently cultivated land will meet the present and future food demand based on scenario analyses considering population growth and changes in dietary habits. By closing yield gaps in the current irrigated and rain-fed cultivated land, about 24% and 80% more crop calories can respectively be produced compared to 2000. Most countries will reach food self-sufficiency or improve their current food self-sufficiency levels if potential crop production levels are achieved. As a novel approach, we defined specific input and agricultural management strategies required to achieve the potential production by overcoming biophysical and socioeconomic constraints causing yield gaps. The management strategies include: fertilizers, pesticides, advanced soil management, land improvement, management strategies coping with weather induced yield variability, and improving market accessibility. Finally, we estimated the required fertilizers (N, P2O5, and K2O to attain the potential yields. Globally, N-fertilizer application needs to increase by 45-73%, P2O5-fertilizer by 22-46%, and K2O-fertilizer by 2-3 times compared to the year 2010 to attain potential crop production. The sustainability of such agricultural intensification largely depends

Possible changes to arable crop yields by 2050.

Science.gov (United States)

Jaggard, Keith W; Qi, Aiming; Ober, Eric S

2010-09-27

By 2050, the world population is likely to be 9.1 billion, the CO(2) concentration 550 ppm, the ozone concentration 60 ppb and the climate warmer by ca 2 degrees C. In these conditions, what contribution can increased crop yield make to feeding the world? CO(2) enrichment is likely to increase yields of most crops by approximately 13 per cent but leave yields of C4 crops unchanged. It will tend to reduce water consumption by all crops, but this effect will be approximately cancelled out by the effect of the increased temperature on evaporation rates. In many places increased temperature will provide opportunities to manipulate agronomy to improve crop performance. Ozone concentration increases will decrease yields by 5 per cent or more. Plant breeders will probably be able to increase yields considerably in the CO(2)-enriched environment of the future, and most weeds and airborne pests and diseases should remain controllable, so long as policy changes do not remove too many types of crop-protection chemicals. However, soil-borne pathogens are likely to be an increasing problem when warmer weather will increase their multiplication rates; control is likely to need a transgenic approach to breeding for resistance. There is a large gap between achievable yields and those delivered by farmers, even in the most efficient agricultural systems. A gap is inevitable, but there are large differences between farmers, even between those who have used the same resources. If this gap is closed and accompanied by improvements in potential yields then there is a good prospect that crop production will increase by approximately 50 per cent or more by 2050 without extra land. However, the demands for land to produce bio-energy have not been factored into these calculations.

Systematics of neutron-induced fission yields

International Nuclear Information System (INIS)

Blachot, J.; Brissot, R.

1983-10-01

The main characteristics of the mass and charge distributions for thermal neutron induced fission of actinides are reviewed. We show that these distributions can be reasonably reproduced with only 24 data as input. We use a representation where the element yields together with the most probable mass Ap(Z) play the dominant role. The ability of this model to calculate mass yields for the fission of not yet measured actinides is also shown. The influence of the excitation energy of the fissile system on charge and mass distribution is also discussed

Quality and Yield of Cannabis Products

DEFF Research Database (Denmark)

Kastorp, Grith; Lindholst, Christian

2011-01-01

Abstract. 180 seizures containing 667 different samples of cannabis products from 5 police districts in Jutland were examined from 2008 to the present. The samples were divided into the groups: hashish, marihuana (leaves and buds) and whole plants (indoors and outdoors). Cannabis seized from indoor...... cultivation was examined in order to determine THC content and yield. The results are used by the Danish Police Attorney to estimate expected yields in cases with unripe cannabis plants. The results indicate that the THC content found in locally grown marihuana is slightly higher than in hashish. However...

High yield fabrication of fluorescent nanodiamonds

International Nuclear Information System (INIS)

Boudou, Jean-Paul; Curmi, Patrick A; Jelezko, Fedor; Wrachtrup, Joerg; Balasubramanian, Gopalakrischnan; Reuter, Rolf; Aubert, Pascal; Sennour, Mohamed; Thorel, Alain; Gaffet, Eric

2009-01-01

A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties.

High yield fabrication of fluorescent nanodiamonds

Energy Technology Data Exchange (ETDEWEB)

Boudou, Jean-Paul; Curmi, Patrick A [Structure and Activity of Normal and Pathological Biomolecules-INSERM/UEVE U829, Universite d' Evry-Val d' Essonne, Batiment Maupertuis, Rue du pere Andre Jarlan, F-91025 Evry (France); Jelezko, Fedor; Wrachtrup, Joerg; Balasubramanian, Gopalakrischnan; Reuter, Rolf [3.Physikalisches Institut, University of Stuttgart, Pfaffenwaldring 57, D-70550 Stuttgart (Germany); Aubert, Pascal [Nanometric Media Laboratory, Universite d' Evry-Val d' Essonne, Batiment Maupertuis, Rue du pere Andre Jarlan, F-91025 Evry (France); Sennour, Mohamed; Thorel, Alain [Centre des Materiaux, Mines Paris, ParisTech, BP 87, F-91000 Evry (France); Gaffet, Eric [Nanomaterials Research Group-UMR 5060, CNRS, UTBM, Site de Sevenans, F-90010 Belfort (France)], E-mail: jpb.cnrs@free.fr, E-mail: pcurmi@univ-evry.fr, E-mail: f.jelezko@physik.uni-stuttgart.de

2009-06-10

A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties.

Yield gap analysis of Chickpea under semi-arid conditions: A simulation study

OpenAIRE

seyed Reza Amiri Deh ahmadi; mehdi parsa; mohammad bannayan aval; mahdi nassiri mahallati

2016-01-01

Yield gap analysis provides an essential framework to prioritize research and policy efforts aimed at reducing yield constraints. To identify options for increasing chickpea yield, the SSM-chickpea model was parameterized and evaluated to analyze yield potentials, water limited yields and yield gaps for nine regions representing major chickpea-growing areas of Razavi Khorasan province. The average potential yield of chickpea for the locations was 2251 kg ha-1, while the water limited yield wa...

Using historical wafermap data for automated yield analysis

International Nuclear Information System (INIS)

Tobin, K.W.; Karnowski, T.P.; Gleason, S.S.; Jensen, D.; Lakhani, F.

1999-01-01

To be productive and profitable in a modern semiconductor fabrication environment, large amounts of manufacturing data must be collected, analyzed, and maintained. This includes data collected from in- and off-line wafer inspection systems and from the process equipment itself. This data is increasingly being used to design new processes, control and maintain tools, and to provide the information needed for rapid yield learning and prediction. Because of increasing device complexity, the amount of data being generated is outstripping the yield engineer close-quote s ability to effectively monitor and correct unexpected trends and excursions. The 1997 SIA National Technology Roadmap for Semiconductors highlights a need to address these issues through open-quotes automated data reduction algorithms to source defects from multiple data sources and to reduce defect sourcing time.close quotes SEMATECH and the Oak Ridge National Laboratory have been developing new strategies and technologies for providing the yield engineer with higher levels of assisted data reduction for the purpose of automated yield analysis. In this article, we will discuss the current state of the art and trends in yield management automation. copyright 1999 American Vacuum Society

Real-time yield estimation based on deep learning

Science.gov (United States)

Rahnemoonfar, Maryam; Sheppard, Clay

2017-05-01

Crop yield estimation is an important task in product management and marketing. Accurate yield prediction helps farmers to make better decision on cultivation practices, plant disease prevention, and the size of harvest labor force. The current practice of yield estimation based on the manual counting of fruits is very time consuming and expensive process and it is not practical for big fields. Robotic systems including Unmanned Aerial Vehicles (UAV) and Unmanned Ground Vehicles (UGV), provide an efficient, cost-effective, flexible, and scalable solution for product management and yield prediction. Recently huge data has been gathered from agricultural field, however efficient analysis of those data is still a challenging task. Computer vision approaches currently face diffident challenges in automatic counting of fruits or flowers including occlusion caused by leaves, branches or other fruits, variance in natural illumination, and scale. In this paper a novel deep convolutional network algorithm was developed to facilitate the accurate yield prediction and automatic counting of fruits and vegetables on the images. Our method is robust to occlusion, shadow, uneven illumination and scale. Experimental results in comparison to the state-of-the art show the effectiveness of our algorithm.

Pink bollworm integrated management using sterile insects under field trial conditions, Imperial Valley, California

International Nuclear Information System (INIS)

Walters, M.L.; Staten, R.T.; Roberson, R.C.

2000-01-01

The pink bollworm moth (Pectinophora gossypiella Saunders) feeds almost exclusively on cotton (Gossypium spp.) and causes economic loss (Pfadt 1978). The pink bollworm (PBW) is often the key pest of cotton in Arizona, southern California, and northwestern Mexico. The larvae (immature stages) bore into the developing cotton fruit, where they feed on the cotton lint and seeds, causing significant damage and dramatically reducing the yield of cotton lint (Pfadt 1978). The PBW is difficult to control with conventional means (insecticides) because it spends the destructive larval phase inside the cotton boll where it is well protected from control measures. Cultural controls, such as a short growing season, have successfully decreased the population in the Imperial Valley (Chu et al. 1992) to the point where eradication may be possible using sterile insects and genetically engineered cotton. Because the PBW is an introduced insect, with few plant hosts other than cultivated cotton, its eradication from continental USA is a desirable and economically attractive alternative to the continued use of pesticides and/or further loss to the pest. Mass releases of sterile insects began in earnest in 1970 in the San Joaquin Valley, California, in order to inhibit normal reproduction and to eradicate the pest in an environmentally responsible manner. Sterile release involves mass production and sexual sterilisation using irradiation (20 krad for PBW adults). This was accomplished by building a rearing facility in Phoenix, AZ. The facility has 6,410 square metres of permanent laboratories, rearing and irradiation chambers and insect packing rooms. The facility operates the year round but with a variable production rate, that is, maximal during the cotton growing season (May through September). Sterile insect technology is based on the monitoring of the native and sterile populations in the field and the subsequent release of appropriate numbers of sterile insects in order to

Ultra-low gossypol cottonseed: gene-silencing opens up a vast, but underutilized protein resource for human nutrition

Science.gov (United States)

Cotton, grown mainly for its fiber, is a major crop in several developing and developed countries across the globe. In 2012, 48.8 million metric tons (MMT) of cottonseed was produced worldwide as a by-product of the 25.9 MMT of cotton lint production (FAO Production Statistics). This amount of cot...

[Study on High-yield Cultivation Measures for Arctii Fructus].

Science.gov (United States)

Liu, Shi-yong; Jiang, Xiao-bo; Wang, Tao; Sun, Ji-ye; Hu, Shang-qin; Zhang, Li

2015-02-01

To find out the high yield cultivation measures for Arctii Fructus. Completely randomized block experiment design method was used in the field planting, to analyze the effect of different cultivation way on agronomic characters, phenological phase,quality and quantity of Arctii Fructus. Arctium lappa planted on August 28 had the best results of plant height, thousand seeds weight and yield. The highest yield of Arctii Fructus was got at the density of 1,482 plants/667 m2. Arctiin content was in an increase trend with the planting time delay and planting density increasing. The plant height, thousand seeds weight, yield and arctiin content by split application of fertilizer were significantly higher than that by one-time fertilization. Compared with open field Arctium lappa, plant height, yield, arctiin content and relative water content of plastic film mulching Arctium lappa was higher by 7.74%, 10.87%, 6.38% and 24.20%, respectively. In the topping Arctium lappa, the yield was increased by 11.09%, with 39. 89% less branching number. Early planting time and topping shortened the growth cycle of Arctium lappa plant. The high-yield cultivation measures of Arctii Fructus are: around August 28 to sowing, planting density of 1 482 plants/667 m2, split application of fertilizer for four times, covering film on surface of the soil and topping in bolting.

Increasing crop diversity mitigates weather variations and improves yield stability.

Science.gov (United States)

Gaudin, Amélie C M; Tolhurst, Tor N; Ker, Alan P; Janovicek, Ken; Tortora, Cristina; Martin, Ralph C; Deen, William

2015-01-01

Cropping sequence diversification provides a systems approach to reduce yield variations and improve resilience to multiple environmental stresses. Yield advantages of more diverse crop rotations and their synergistic effects with reduced tillage are well documented, but few studies have quantified the impact of these management practices on yields and their stability when soil moisture is limiting or in excess. Using yield and weather data obtained from a 31-year long term rotation and tillage trial in Ontario, we tested whether crop rotation diversity is associated with greater yield stability when abnormal weather conditions occur. We used parametric and non-parametric approaches to quantify the impact of rotation diversity (monocrop, 2-crops, 3-crops without or with one or two legume cover crops) and tillage (conventional or reduced tillage) on yield probabilities and the benefits of crop diversity under different soil moisture and temperature scenarios. Although the magnitude of rotation benefits varied with crops, weather patterns and tillage, yield stability significantly increased when corn and soybean were integrated into more diverse rotations. Introducing small grains into short corn-soybean rotation was enough to provide substantial benefits on long-term soybean yields and their stability while the effects on corn were mostly associated with the temporal niche provided by small grains for underseeded red clover or alfalfa. Crop diversification strategies increased the probability of harnessing favorable growing conditions while decreasing the risk of crop failure. In hot and dry years, diversification of corn-soybean rotations and reduced tillage increased yield by 7% and 22% for corn and soybean respectively. Given the additional advantages associated with cropping system diversification, such a strategy provides a more comprehensive approach to lowering yield variability and improving the resilience of cropping systems to multiple environmental

Search for the rare decays B{sub s}{sup 0}{yields}{mu}{sup +}{mu}{sup -} and B{sup 0}{yields}{mu}{sup +}{mu}{sup -}

Energy Technology Data Exchange (ETDEWEB)

Aaij, R. [Nikhef National Institute for Subatomic Physics, Amsterdam (Netherlands); Abellan Beteta, C. [Universitat de Barcelona, Barcelona (Spain); Adeva, B. [Universidad de Santiago de Compostela, Santiago de Compostela (Spain); Adinolfi, M. [H.H. Wills Physics Laboratory, University of Bristol, Bristol (United Kingdom); Adrover, C. [CPPM, Aix-Marseille Universite, CNRS/IN2P3, Marseille (France); Affolder, A. [Oliver Lodge Laboratory, University of Liverpool, Liverpool (United Kingdom); Ajaltouni, Z. [Clermont Universite, Universite Blaise Pascal, CNRS/IN2P3, LPC, Clermont-Ferrand (France); Albrecht, J.; Alessio, F. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Alexander, M. [School of Physics and Astronomy, University of Glasgow, Glasgow (United Kingdom); Alkhazov, G. [Petersburg Nuclear Physics Institute (PNPI), Gatchina (Russian Federation); Alvarez Cartelle, P. [Universidad de Santiago de Compostela, Santiago de Compostela (Spain); Alves, A.A. [Sezione INFN di Roma La Sapienza, Roma (Italy); Amato, S. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro (Brazil); Amhis, Y. [Ecole Polytechnique Federale de Lausanne (EPFL), Lausanne (Switzerland); Anderson, J. [Physik-Institut, Universitaet Zuerich, Zuerich (Switzerland); Appleby, R.B. [School of Physics and Astronomy, University of Manchester, Manchester (United Kingdom); Aquines Gutierrez, O. [Max-Planck-Institut fuer Kernphysik (MPIK), Heidelberg (Germany); Archilli, F. [Laboratori Nazionali dell' INFN di Frascati, Frascati (Italy); European Organization for Nuclear Research (CERN), Geneva (Switzerland); Arrabito, L. [CC-IN2P3, CNRS/IN2P3, Lyon-Villeurbanne (France); and others

2012-02-14

A search for the decays B{sub s}{sup 0}{yields}{mu}{sup +}{mu}{sup -} and B{sup 0}{yields}{mu}{sup +}{mu}{sup -} is performed with 0.37 fb{sup -1} of pp collisions at {radical}(s)=7 TeV collected by the LHCb experiment in 2011. The upper limits on the branching fractions are B(B{sub s}{sup 0}{yields}{mu}{sup +}{mu}{sup -})<1.6 Multiplication-Sign 10{sup -8} and B(B{sup 0}{yields}{mu}{sup +}{mu}{sup -})<3.6 Multiplication-Sign 10{sup -9} at 95% confidence level. A combination of these results with the LHCb limits obtained with the 2010 dataset leads to B(B{sub s}{sup 0}{yields}{mu}{sup +}{mu}{sup -})<1.4 Multiplication-Sign 10{sup -8} and B(B{sup 0}{yields}{mu}{sup +}{mu}{sup -})<3.2 Multiplication-Sign 10{sup -9} at 95% confidence level.

Technological possibilities for increasing coarse coal yield in the Staszic mine

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Major, M

1985-06-01

Experiments carried out in the Staszic underground black coal mine in Upper Silesia showed that there is a correlation of coarse coal yield and yield strength of shield supports used at longwall faces. The faces were equipped with Pioma 25-45, Fazos 15-31 and Fazos 19-32 shield supports, KWB 3RDU shearer loaders and Rybnik chain conveyors. Pressure of oil in water emulsion used in the Pioma 25/45 shield supports was reduced from the recommended 30 MPa to 15 MPa or to 10 MPa. Reducing emulsion pressure (and support yield strength) caused an increase in coarse coal yield. Coarse coal yield was also increased by use of Fazos 19/32 shield supports with reduced yield strength. During the tests coarse coal yield increased 1.68% and 2.65%. Test results are shown in 3 diagrams. Investigations carried out in the Staszic mine in 1983 showed that by optimizing yield strength of shield supports coarse coal yield could be increased 2 to 8%. 6 references.

Effect of Black and Clear Polyethylene Mulch on Yield and Yield Components of Melon in Salinity Stress Condition

Directory of Open Access Journals (Sweden)

Peyman Jafari

2017-02-01

Full Text Available Introduction: The term of Mulch, is the German word (Molsh means the soft, however, not soft, and made of plant debris or synthetic substances. Many positive effects attributed to the use of plastic mulch such as adjusting the temperature in the root environment, conserve moisture, reduce weeds, increase root growth, reduce soil erosion, and soil condensation and improve germination and early plant establishment. The use of mulch can reduce the harmful effects of salt in plants. Materials and Methods: To evaluate the effects of black and clear polyethylene mulch on yield and yield components of melon in salinity stress condition, a study was conducted in 2011 using split plot randomized based on complete block design with three replications in Varamin region. Three salinity levels of irrigation water of 2, 5 and 8 dS-1 as main factor and three plastic mulch treatments (no mulch, clear mulch and black mulch were considered as sub-plots. At harvest and after determining the yield and number of fruits harvested from each plot, the average number of fruits per plant was measured and fruit pulp thickness was recorded with calipers. Results Discussion The results showed interactive effects of salinity and mulch on fruit yield, number of fruits per plant, average fruit weight, fruit length, days to first harvest and fruit soluble solids percentage were statistically significant. In salinity levels of 2, 5 and 8 dS m-1, fruit yield increased, respectively, 19.6, 59, and 45.4 %in clear mulch compared to control. Similarly these increases for the black mulch were equal to 15.7, 41.9, and 21.4 percent, respectively. With 2, 5 and 8 dS m-1 salinity levels, fruit yield in the first harvest were 7.44, 7.72, and 6.98 t ha -1, respectively, which was significantly higher than without mulch and black mulch. Mulch can reduce evaporation and increase the level of moisture in the soil and thereby dilute the salt and reduce the harmful effects of salinity. Some

Benefits of inoculation, P fertilizer and manure on yields of common bean and soybean also increase yield of subsequent maize

NARCIS (Netherlands)

Rurangwa, Edouard; Vanlauwe, Bernard; Giller, Ken E.

2018-01-01

Common bean and soybean yield poorly on smallholder farms in Rwanda. We evaluated the benefits of inoculation combined with P fertilizer and manure on yields of common bean and soybean in three agro-ecological zones (AEZs), and their residual effects on a subsequent maize crop. In the first season,

Influence of surface topography on the sputtering yields of silver

International Nuclear Information System (INIS)

Pan Jisheng; Wang Zhenxia; Tao Zhenlan; Zhang Jiping

1992-01-01

The sputtering yields of silver have been measured as a function of the fluence of incident Ar + ions (27 keV) using the collector technique and RBS analysis. The irradiated surface was examined by scanning electron microscopy (SEM). It is shown that the sputtering yields of surfaces with topography are enhanced relative to smooth surfaces of silver, but the extent of the enhancement depends on the irradiation dose. The experimental results can be explained assuming that the surface topography and sputtering yield are a function of incident angle. It is obvious that the surface topography is an important factor to influence the sputtering yield. The term ''apparent sputtering yield'' has specifically been used when referring to the experimental sputtering yield of a surface with topography, to emphasize the difference with a smooth surface. (orig.)

Investigating the Effect of Cultivate Lines Direction, Bio-Fertilizer Nitroxin and Superabsorbent Materials on Yield and Yield Components of Broad Leaf Vetch (Vicia narbonensis

Directory of Open Access Journals (Sweden)

E Latifinia

2017-12-01

Full Text Available Introduction The excessive use of fertilizers has caused severe damages to the bio-cycle in the fields and has destroyed the sustainable agricultural machinery. These destructive effects have led to the recommended use of bio-fertilizers. Biodiversity is one of the key sources of supplying nutrients in sustainable agriculture. The use of biological fertilizers in a sustainable agricultural system leads to sustained yield in plant production. Biological fertilizer of nitroxin has increased biological yield and grain yield in fodder corn. Water shortage as a limiting factor has limited vegetation growth and development in these areas. Considering that Iran is a dry country, the use of super adsorbent is one of the ways to reduce water consumption. Investigators in the study of superabsorbent showed that superabsorbent had a significant and positive effect on the yield of forage plants. Crop directions can affect the amount of the product by increasing the leaf area and absorbing light. Proper orientation of crop lines increases the photosynthetic efficiency and increases the yield and yield components of the plant. Research has shown that yields are much higher in plants planted on the north-south lines compared with plants planted on east-west lines. Materials and Methods In order to investigate the effect of nitroxin and superabsorbent fertilizer on yield and yield components of broad leaf vetch in a research field of agricultural faculty, Lorestan University, as a split plot factorial based on a complete block design randomization was performed in three replicates. In this research, for main lines, the main factors were considered in the North-South and East-West directions in the main plots. Sub-factors In this experiment, nitroxin biosynthesis and superabsorbent materials were applied at two levels of consumption and non-consumption in sub plots. Nitroxin fertilizer was used as a seed lot at a rate of 1 liter per hectare and the stockosorb

Effects of shade and drought stress on soybean hormones and yield ...

African Journals Online (AJOL)

Jane

2011-10-24

Oct 24, 2011 ... hormone concentrations, main-stem and branch yield response to the combination of shade and drought were studied ... yield primarily by reducing branch growth and branch seed yield per ..... deficit soybean. Yield decrease ...

The 'Golden' cLFV channels {mu} {yields} e{gamma} and {mu} {yields} eee - the high-intensity frontier

Energy Technology Data Exchange (ETDEWEB)

Kettle, Peter-Raymond, E-mail: peter-raymond.kettle@psi.ch [Paul Scherrer Institut PSI, Laboratory for Particle Physics (Switzerland)

2013-03-15

The muon as a laboratory for studying charged lepton-flavour violation (cLFV) has proven to be one of the most sensitive areas to probe for 'New Physics', due to the muon's copious production rate and relatively long lifetime. The search at the intensity frontier with precision-type experiments is complementary to the search for new particles at the high-energy frontier of TeV colliders. Of the three 'golden' muon channels: {mu} {yields} e{gamma}, {mu} {yields} 3e and {mu} {yields} econversion, an overview of the status of the coincidence experiments MEG, together with the latest results, which constitute the most stringent limit to date on this decay and the recently initiated Mu3e experiment, will be given.

Weed biomass and economic yield of wheat (Triticum aestivum) as ...

African Journals Online (AJOL)

Yomi

2012-01-24

Jan 24, 2012 ... INTRODUCTION ... to control weeds in conjunction with cultural practices. Jarwar et al. (1999) .... Wheat grain yield is an interplay of yield components especially ... The biological yield expresses the overall growth of crop.

Soil Texture and Cultivar Effects on Rice (Oryza sativa, L. Grain Yield, Yield Components and Water Productivity in Three Water Regimes.

Directory of Open Access Journals (Sweden)

Fugen Dou

Full Text Available The objective of this study was to determine the effects of water regime/soil condition (continuous flooding, saturated, and aerobic, cultivar ('Cocodrie' and 'Rondo', and soil texture (clay and sandy loam on rice grain yield, yield components and water productivity using a greenhouse trial. Rice grain yield was significantly affected by soil texture and the interaction between water regime and cultivar. Significantly higher yield was obtained in continuous flooding than in aerobic and saturated soil conditions but the latter treatments were comparable to each other. For Rondo, its grain yield has decreased with soil water regimes in the order of continuous flooding, saturated and aerobic treatments. The rice grain yield in clay soil was 46% higher than in sandy loam soil averaged across cultivar and water regime. Compared to aerobic condition, saturated and continuous flooding treatments had greater panicle numbers. In addition, panicle number in clay soil was 25% higher than in sandy loam soil. The spikelet number of Cocodrie was 29% greater than that of Rondo, indicating that rice cultivar had greater effect on spikelet number than soil type and water management. Water productivity was significantly affected by the interaction of water regime and cultivar. Compared to sandy loam soil, clay soil was 25% higher in water productivity. Our results indicated that cultivar selection and soil texture are important factors in deciding what water management option to practice.

Measure of the e+e-{yields}bb Cross Section at the LEP Energies; Medida de la seccion eficaz e''+e''-{yields}bb a las Energias de LEP

Energy Technology Data Exchange (ETDEWEB)

Arce Dubois, P

1992-07-01

In the present work I analyse the data collected during 1990 by the L3 detector, situated in the electron-positron collider LEP. After selecting the events e''+e''-{yields} bb through their semileptonic decays into muons, I calculate the cross section for the process e''+e''- {yields} bb at different energy points around the mass of the vectorial boson Z, and I measure some parameters of the Standard Model, namely, the Br(b{yields}{mu} ),{gamma}{sub z}n-{yields}bb/{gamma}{sub z}n{yields}had and {gamma}{sub z}n{yields}bb{gamma}{sub z}n{yields}e''+e''-. (Author) 26 refs.

Dual-component video image analysis system (VIASCAN) as a predictor of beef carcass red meat yield percentage and for augmenting application of USDA yield grades.

Science.gov (United States)

Cannell, R C; Tatum, J D; Belk, K E; Wise, J W; Clayton, R P; Smith, G C

1999-11-01

An improved ability to quantify differences in the fabrication yields of beef carcasses would facilitate the application of value-based marketing. This study was conducted to evaluate the ability of the Dual-Component Australian VIASCAN to 1) predict fabricated beef subprimal yields as a percentage of carcass weight at each of three fat-trim levels and 2) augment USDA yield grading, thereby improving accuracy of grade placement. Steer and heifer carcasses (n = 240) were evaluated using VIASCAN, as well as by USDA expert and online graders, before fabrication of carcasses to each of three fat-trim levels. Expert yield grade (YG), online YG, VIASCAN estimates, and VIASCAN estimated ribeye area used to augment actual and expert grader estimates of the remaining YG factors (adjusted fat thickness, percentage of kidney-pelvic-heart fat, and hot carcass weight), respectively, 1) accounted for 51, 37, 46, and 55% of the variation in fabricated yields of commodity-trimmed subprimals, 2) accounted for 74, 54, 66, and 75% of the variation in fabricated yields of closely trimmed subprimals, and 3) accounted for 74, 54, 71, and 75% of the variation in fabricated yields of very closely trimmed subprimals. The VIASCAN system predicted fabrication yields more accurately than current online yield grading and, when certain VIASCAN-measured traits were combined with some USDA yield grade factors in an augmentation system, the accuracy of cutability prediction was improved, at packing plant line speeds, to a level matching that of expert graders applying grades at a comfortable rate.

Effect of Mycorrhizal Fungus (Glomus spp on Wheat (Triticumaestivum Yield and Yield Components with Regard to Irrigation Water Quality

Directory of Open Access Journals (Sweden)

S Habibi

2016-02-01

Full Text Available Introduction Decrease in water quality affected by salinization of the water resources due to the drought is one of the limiting factors of plant production. Using mycorrhizal fungi is an important approach to deal with damaging effects during stress conditions. The symbiosis of arbuscular mycorrhiza (AM with the host plant and hence, the production of a very extensive network of hypha, enhances nutrient acquisition and improves water uptake in the host plant. The specialized network of hypha raises the uptake and translocation of nutrients to the plant, whereas it inhibits high uptake of Na and Cl and their transport to plant shoots compared with plant roots. Hence, AM can alleviate the stress of salinity on plant growth and increases their tolerance to the stresses. Materials and Methods In order to evaluate the influence of mycorrhizal fungi on yield and yield components of wheat, a greenhouse experiment was conducted in research farm of Shahid Chamran Ahvaz University. Experimental design was a randomized complete block design arranged in split factorial with three replications. The factors were water salinity (water quality including filtered water (EC ≥ 1 dS m-1, tap water (EC = 1/7-3 ds m-1, tap water plus NaCl and filtered water plus NaCl (EC = 8 ds m-1. Soil sterilization included sterilized and non-sterilized soil and mycorrhizal inoculation were in five levels (non-inoculated, inoculated with ‌Glomusmosseae, G. intraradices, G. geosporum and mixture of them. Yield and yield components were measured at crop maturity and colonization percentage of root was determined at flowering stage. Root colonization by AM was determined through preparing root samples at 1 g in each experimental unit, and roots were stained using the Gridline- Intersect Method. The harvest index and mycorrhizal dependency were also measured. Salinity levels determined approximate the threshold of wheat –tolerate- salinity before the results would rather

Economics and yields of energy plantations: Status and potential

International Nuclear Information System (INIS)

Kenney, W.A.; Gambles, R.L.; Zsuffa, L.

1992-01-01

A study was carried out to: determine the factors affecting the cost of energy conversion feedstocks in short rotation intensive culture plantations of trees; determine the factors influencing biomass yield; identify interrelationships between the previous two objectives; present estimates of potential biomass yields and associated economics; and to identify gaps in the knowledge of the economics and yields of biomass production and their interrelationships. Reported costs for most aspects had a wide range. Currently, yields of 10-15 dry Mg/hectare/y are readily achievable. Using the cost and yield data, and assuming a biomass price of $40/dry Mg, a series of cash flow analyses were performed. For the low cost inputs, all scenarios were marginally profitable. For the high cost inputs, none of the scenarios were profitable. A current scenario, using figures for contract farming, was not profitable, however this system would break even with a yield of 23.3 dry Mg/hectare/y, within the range of some production clones. A future scenario using farm labour with increased productivity, product values, and machinery efficiencies yielded a profit-making situation. The addition of incentives increased profitability. There is great potential for the production of woody biomass in Canada as a feedstock for energy and other products. Continued and more intensive breeding and selection to develop high yielding stress tolerant clones, cost efficient harvesting systems, continued research into optimization of planting density, rotation length and cultural techniques, and characterization of promising clones with respect to nutrient-use efficiency, site requirements and pest/disease resistance are important areas for further work. 81 refs., 3 figs., 13 tabs

Rice Research to Break Yield Barriers

Science.gov (United States)

Verma, Vivek; Ramamoorthy, Rengasamy; Kohli, Ajay; Kumar, Prakash P.

2015-10-01

The world’s population continues to expand and it is expected to cross 9 billion by 2050. This would significantly amplify the demand for food, which will pose serious threats to global food security. Additional challenges are being imposed due to a gradual decrease in the total arable land and global environmental changes. Hence, it is of utmost importance to review and revise the existing food production strategies by incorporating novel biotechnological approaches that can help to break the crop yield barriers in the near future. In this review, we highlight some of the concerns hampering crop yield enhancements. The review also focuses on modern breeding techniques based on genomics as well as proven biotechnological approaches that enable identification and utilization of candidate genes. Another aspect of discussion is the important area of research, namely hormonal regulation of plant development, which is likely to yield valuable regulatory genes for such crop improvement efforts in the future. These strategies can serve as potential tools for developing elite crop varieties for feeding the growing billions.

Effect of Different Sources of Nitrogen and Organic Fertilizers on Yield and Yield Components of Ajowan (Trachyspermum ammi L.

Directory of Open Access Journals (Sweden)

zahra saydi

2017-09-01

Full Text Available Introduction Ajowan (Trachyspermum ammi L. is an annual medicinal plant of the family Apiaceae which can reach 30 -100 cm in height. and its growth is highly depended on the availability of mineral nutrients in the soil. But, it has been shown that utilization of chemical fertilizers for growth promotion of Ajown could have negative impacts on environment and ecological systems. Nowadays, sustainable agriculture is the best approach to overcome such problems and prevent the excess accumulation of chemical fertilizers deposited within the soil. Application of bio-fertilizers as an alternative to chemical fertilizers is a new sustainable approach which have been raised in the new era of Agriculture. Therefore, this study was conducted to investigate the application of various source of biological fertilizers such as Vermicompost, Alkazotplus and Humic Acid in combination with nitrogen fertilizers on growth behavior, yield and yield components of Ajowan under Ahvaz growing condition. Materials and methods This research was conducted at the Agricultural Research Station of Shahid Chamran University in 2014-2015 to determine the effects of different sources of nitrogen and organic fertilizers on the yield and yield components of Ajowan based on two way randomized complete block design with three replications. The first factor of the experiment was Application of four different nitrogen sources including: Urea (U, Sulfur-coated Urea (SCU, %50 Sulfur-coated urea (1/2 SCU + Alkazot Plus biological fertilizer and Control (no nitrogen source used. Organic fertilizers were also applied at four levels, consisting of Humic Acid, Vermicompost, %50 Vermicompost + Humic Acid and Control (no organic Fertilizer as the second factor. After soil preparation, approximately four Kg.ha-1 of the seeds were planted on the rows with 30 cm distance. Plant height, number of sub branches, number of umbels per plant, number of seeds per umbel , 1000 seeds weight, biological

Climate change impacts on crop yield: evidence from China.

Science.gov (United States)

Wei, Taoyuan; Cherry, Todd L; Glomrød, Solveig; Zhang, Tianyi

2014-11-15

When estimating climate change impact on crop yield, a typical assumption is constant elasticity of yield with respect to a climate variable even though the elasticity may be inconstant. After estimating both constant and inconstant elasticities with respect to temperature and precipitation based on provincial panel data in China 1980-2008, our results show that during that period, the temperature change contributes positively to total yield growth by 1.3% and 0.4% for wheat and rice, respectively, but negatively by 12% for maize. The impacts of precipitation change are marginal. We also compare our estimates with other studies and highlight the implications of the inconstant elasticities for crop yield, harvest and food security. We conclude that climate change impact on crop yield would not be an issue in China if positive impacts of other socio-economic factors continue in the future. Copyright © 2014 Elsevier B.V. All rights reserved.

PERFORMANCE OF YIELD AND YIELD CONTRIBUTING CHARACTERISTICS OF BC2F3 POPULATION WITH ADDITION OF BLAST RESISTANT GENE

Directory of Open Access Journals (Sweden)

Muhammad Mahmudul Hasan

2015-10-01

Full Text Available ABSTRACTThe study was carried out in the University Putra Malaysia (UPM Rice Research Centre to evaluate the yield performance of newly developed selected blast resistant plants of BC2F3 generations derived from a cross between MR263, a high yielding rice variety but blast susceptible and Pongsu Seribu 1, donor with blast resistant (Pi-7(tand Pi-d (t1, Pir2-3(tgenes and qLN2 QTL, Malaysian local variety. On the basis of assessed traits, the plants 12, 6, 7, 5, 21, 22, 5, 26, 11, 8, 10, 13 and 15 had the higher yield, blast resistant and good morphological traits. More than 70% heritability was found in days to maturity, plant height, tiller numbers per hill, and panicle per hill, 80% heritability was found in filled grain and yield per hill and more than 90% heritability was found in grain length, grain width and seed weight. Cluster analysis based on the traits grouped 30 plants along with MR263 into seven clusters. According to PCA, the first four principal components account for about 69.3% total variation for all measured traits and exhibited high correlation among the characteristics analyzed.

Photofission observations in reactor environments using selected fission-product yields

International Nuclear Information System (INIS)

Gold, R.; Ruddy, F.H.; Roberts, J.H.

1982-01-01

A new method for the observation of photofission in reactor environments is advanced. It is based on the in-situ observation of fission product yield. In fact, at a given in-situ reactor location, the fission product yield is simply a weighted linear combination of the photofission product yield, Y/sub gamma/, and the neutron induced fission product yield, Y/sub n. The weight factors arising in this linear combination are the photofission fraction and neutron induced fission fraction, respectively. This method can be readily implemented with established techniques for measuring in-situ reactor fission product yield. For example, one can use the method based on simultaneous irradiation of radiometric (RM) and solid state track recorder (SSTR) fission monitors. The sensitivity and accuracy and current knowledge of fission product yields. Unique advantages of this method for reactor applications are emphasized

A crop model-based approach for sunflower yields

Directory of Open Access Journals (Sweden)

João Guilherme Dal Belo Leite

2014-10-01

Full Text Available Pushed by the Brazilian biodiesel policy, sunflower (Helianthus annuus L. production is becoming increasingly regarded as an option to boost farmers' income, particularly under semi-arid conditions. Biodiesel related opportunities increase the demand for decision-making information at different levels, which could be met by simulation models. This study aimed to evaluate the performance of the crop model OILCROP-SUN to simulate sunflower development and growth under Brazilian conditions and to explore sunflower water- and nitrogen-limited, water-limited and potential yield and yield variability over an array of sowing dates in the northern region of the state of Minas Gerais, Brazil. For model calibration, an experiment was conducted in which two sunflower genotypes (H358 and E122 were cultivated in a clayey soil. Growth components (leaf area index, above ground biomass, grain yield and development stages (crop phenology were measured. A database composed of 27 sunflower experiments from five Brazilian regions was used for model evaluation. The spatial yield distribution of sunflower was mapped using ordinary kriging in ArcGIS. The model simulated sunflower grain productivity satisfactorily (Root Mean Square Error ≈ 13 %. Simulated yields were relatively high (1,750 to 4,250 kg ha-1 and the sowing window was fairly wide (Oct to Feb for northwestern locations, where sunflower could be cultivated as a second crop (double cropping at the end of the rainy season. The hybrid H358 had higher yields for all simulated sowing dates, growth conditions and selected locations.

Colonoscopy: Evaluating indications and diagnostic yield

International Nuclear Information System (INIS)

Al-Shamali, Mohammed A.; Hasan, F.; Siddiqe, I.; Al-Nakeeb, B.; Kalaoui, M.; Khajah, A.

2001-01-01

Colonoscopic procedure is an accepted modality for the evaluation ofcolonic disease. Open-access versus restricted-access colonoscopy has beenargued over in the recent literature. The aim of this retrospective analysisis to identify the yield of the major indications for the procedure, and thepattern of colon pathology in our community. We retrospectively analyzed ourexperience in 3000 colonoscopies over a five-year period. The patientscomprised 1145 females (38%) and 1855 males (62%) and their ages ranged from9 months to 95 years (mean 39.2). There were 2283 patients (76%) who wereaged less than 55 years. Complete examination to the cecum was possible in2850 cases (95%). Pathological findings were identified in 640 patients(21%). The diagnostic yield of patients referred for lower abdominal pain andsurveillance was low, at 7% and 17%, respectively. The yield was high forthose with lower gastrointestinal bleeding (47%), non-bloody diarrhea (35%),iron deficiency anemia (30%), mass lesions identified by radiology (53%) andpolyps identified by radiology (70%). Inflammatory bowel disease wasdiagnosed in 220 patients, carcinoma in 64 patients and colonic polyps in 139patients. Colonic diseases are not uncommon in our part of the world.Colonoscopy is a rewarding procedure in those patients referred with lowergastrointestinal bleeding, mass lesions, polyps and diarrhea. The procedureis less rewarding in patients with lower abdominal pain and in thoseundergoing surveillance colonoscopy. Patient selection on the basis of thepresenting complaint may help to utilize the limited resource available togastroenterologists. About 63% of the procedures were done for indicationsfound to have a low yield. Inflammatory bowel disease is seen with increasingfrequency in our population. (author)

Effect of integrated plant nutrition and irrigation scheduling on yield and yield components of maize (zea mays l.)

International Nuclear Information System (INIS)

Randhawa, M.S.; Maqsood, M.; Wajid, S.A.; Haq, A.U.

2012-01-01

Effect of three irrigation schedules (4-6 irrigations) and seven integrated plant nutrition levels (control, 125-60-62 kg N-P/sub 2/O/sub 5/-K/sub 2/O ha/sup -1/, 125-60-62 kg N-P/sub 2/O/sub 5/--K/sub 2/O ha/sup -1/ + Farmyard manure at the rate 10 t ha/sup -1/, 125-60-62 kg N-P/sub 2/O/sub 5/-K/sub 2/O ha/sup -1/ + Farm yard manure at the rate 15 t ha-1, 250-120-125 kg N-P/sub 2/O/sub 5/--K/sub 2/O ha-1, 250-120-125 kg N-P/sub 2/O/sub 5/ -K/sub 2/O ha/sup -1/ + Farmyard manure at the rate 10 t ha-1 and 250-120-125 kg N-P/sub 2/O/sub 5/--K/sub 2/O ha/sup -1/ + Farmyard manure at the rate 15 t ha/sup -1/) on grain yield and its components in maize were studied during 2009 and 2010. Plant height, number of cobs plant-1, number of grain rows cob-1, number of grains cob-1, 1000-grain weight, grain weight cob-1, grain yield, stover yield and biological yield were significantly affected by irrigation schedules and integrated plant nutrition levels during both years. The crop applied with six irrigations and fertilized by integrated application of chemical fertilizers (250-120-125 kg N-P/sub 2/O/sub 5/--K/sub 2/O ha/sup -1/) and farmyard manure (15 t ha/sup -1/) produced the highest grain yield of 8.47 t ha/sup -1/ and 8.22 t ha/sup -1/ during 2009 and 2010, respectively. (author)

The Effect of Sowing Date and Plant Density on Yield and Yield Components of Roselle (Hibiscus sabdariffa L. under Jiroft Climate Conditions

Directory of Open Access Journals (Sweden)

B Parsa Motlagh

2017-03-01

Full Text Available Introduction Details of the mutual effect with the agronomic factors, genetic and climatic conditions should be identified to crop a plant in a new area. The purpose of sowing date determination is to find the desired planting time as environmental factors at the time that is suitable for growing, seedling and plant’s survival and resume of growth and development and the plant does not meet unfavorable conditions. The plant density is the most important influencing factors on the development and production of medicinal plants and is an important factor in achieving optimal performance. This research has been conducted for determination of best sowing date and intra row Roselle cultivation in Jiroft area. The objectives of the study were to evaluate the effects of plant density and sowing date on yield, yield components and some of morphological traits on Rosellee (Hibiscus sabdariffa L. and also determine the optimum intra-row spacing and sowing date in order to obtain better yield in Jiroft environment conditions. Materials and Methods The field experiment was split plot in a randomized complete blocks design with three replications in agricultural research field (Long. 57°44´ E., Lat. 28°40´ N., Alt. 650 m of Jiroft University at 2013-2014 growing season. Main plots were sowing date at five levels of 11th and 30th March, 14th April, 5th and 22th May and intra-rows were spaced of 100, 75 and 50 cm as sub plot. Each plot was 3×6 m. The spacing was 1 m between sub-plots, 2 m between main plots and replications. Traits such as plant height, the number of branches, the number of bolls per plant, boll dry weight of plant, sepal yield, seed yield, biomass yield, seed harvest index, and sepal harvest index were measured. Plants were harvested on 1th December, 2014. An area equivalent to 2 × 3 square meters from the center of each plot was harvested by removing the effect of marginal plants from the soil surface to measure the yield of sepal

Surface-enhanced light olefin yields during steam cracking

NARCIS (Netherlands)

Golombok, M.; Kornegoor, M.; Brink, van den P.; Dierickx, J.; Grotenbreg, R.

2000-01-01

Various papers have shown enhanced olefin yields during steam cracking when a catalytic surface is introduced. Our studies reveal that increased light olefin yields during catalytic steam cracking are mainly due to a surface volume effect and not to a traditional catalytic effect. Augmentation of

Maximizing the ExoEarth candidate yield from a future direct imaging mission

International Nuclear Information System (INIS)

Stark, Christopher C.; Roberge, Aki; Mandell, Avi; Robinson, Tyler D.

2014-01-01

ExoEarth yield is a critical science metric for future exoplanet imaging missions. Here we estimate exoEarth candidate yield using single visit completeness for a variety of mission design and astrophysical parameters. We review the methods used in previous yield calculations and show that the method choice can significantly impact yield estimates as well as how the yield responds to mission parameters. We introduce a method, called Altruistic Yield Optimization, that optimizes the target list and exposure times to maximize mission yield, adapts maximally to changes in mission parameters, and increases exoEarth candidate yield by up to 100% compared to previous methods. We use Altruistic Yield Optimization to estimate exoEarth candidate yield for a large suite of mission and astrophysical parameters using single visit completeness. We find that exoEarth candidate yield is most sensitive to telescope diameter, followed by coronagraph inner working angle, followed by coronagraph contrast, and finally coronagraph contrast noise floor. We find a surprisingly weak dependence of exoEarth candidate yield on exozodi level. Additionally, we provide a quantitative approach to defining a yield goal for future exoEarth-imaging missions.

Central Bank Communication and the Yield Curve

DEFF Research Database (Denmark)

Leombroni, Matteo; Vedolin, Andrea; Venter, Gyuri

countries. We study two explanations for this finding, revelation of the ECB’s private information and credit risk, and argue that neither channel can explain the effect on yield spreads. Motivated by this, we consider an alternative explanation in which central bank communication affects the aggregate...... demand due to the presence of reaching-for-yield investors. We show that a resulting risk premium channel helps to rationalize our findings....

Evaluation of symbiosis with Mycorhizzal on yield, yield components and essential oil of fennel (Foeniculum vulgare Mill. and ajowan (Carum copticum L. under different nitrogen levels

Directory of Open Access Journals (Sweden)

J. Shabahang

2016-05-01

Full Text Available In order to investigate the effects of mycorrhiza symbiosis and different nitrogen levels on yield, yield components and essential oil content and yield of fennel (Foeniculum vulgare Mill. and ajowan (Carum copticum L., a field experiment was arranged in a factoriel based on a randomized complete block design with three replications at the Agricultural Research Station, Ferdowsi University of Mashhad during growing season 2009-2010. The first and the second factors were inoculation with mycorrhiza (with and without inoculation and nitrogen levels as Urea (0, 50 and 100 kg.ha-1, respectively. Inculated soil with 200 g mycorrhiza (Glomus intraradaices was applied at planting time. Urea was used in two stages such as plating time and one month after that. Ceriteria such as yield components (including number of branch, umbel, umbellet, seed and seed weight, biological and seed yield, harvest index and essential oil content and yield of fennel and ajowan were measured. Results showed that yield components, seed yield, biological yield, harvest index, essential oil content and yield of fennel and ajowan were affected by mycorrhiza and nitrogen level. Mycorrhiza increased fennel and ajowan seed yield (with 35 and 85%, respectively and essential oil content (with 34 and 30%, respectively. The highest and the lowest 1000-seed weight of fennel and ajowan obsevered in inoculation (2.9 and 0.3 g and control (2.1 and 0.2 g, respectively. Nitrogen improved all growth characteristics and decreased essential oil content. There were not significant differences between mycorrhiza and nitrogen interaction. Inoculation with mycorrhiza enhanced root development and hence availability of nutrients, particularly phosphorus. Also, nitrogen is the cause of increasement of photosynthesis rate and duration which promote growth and yield, but it declined essential oil content of two species.

Biases in Farm-Level Yield Risk Analysis due to Data Aggregation

NARCIS (Netherlands)

Finger, R.

2012-01-01

We investigate biases in farm-level yield risk analysis caused by data aggregation from the farm-level to regional and national levels using the example of Swiss wheat and barley yields. The estimated yield variability decreases significantly with increasing level of aggregation, with crop yield

Coal mine subsidence: effects of mitigation on crop yields

International Nuclear Information System (INIS)

Darmody, R.G.; Hetzler, R.T.; Simmons, F.W.

1992-01-01

Subsidence from longwall underground coal mining adversely impacts agricultural land by creating wet or ponded areas. While most subsided areas show little impact, some localized places, usually less than 1.5 ha in size, may experience total crop failure. Coal companies mitigate subsidence damaged cropland by installing drainage waterways or by adding fill material to raise the grade. The objective of this study was to test the effectiveness of mitigation in restoring corn and soybean yields to pre-mined levels. Fourteen sites in southern Illinois were selected for study. Corn (Zea mays L.) and soybean (Glycine max L.) yields from mitigated and nearby undisturbed areas were compared for four years. Results varied due to differing weather and site conditions. Mean corn yields overall, however were significantly (α0.05) lower on mitigated areas. There was no significant difference in overall mean soybean yields. Soil fertility levels were similar and did not account for yield differences. 14 refs., 1 fig., 7 tabs

Molecular Mapping of QTLs for Yield and Yield-Related Traits in Oryza sativa cv Swarna × O. nivara (IRGC81848 Backcross Population

Directory of Open Access Journals (Sweden)

B.P. MALLIKARJUNA SWAMY

2011-09-01

Full Text Available Advanced backcross QTL analysis was used to identify QTLs for seven yield and yield-related traits in a BC2F2 population from the cross between a popular Oryza sativa cv Swarna and O. nivara IRGC81848. Transgressive segregants with more than 15% increased effect over Swarna were observed for all the traits except days to heading and days to 50% flowering. Thirty QTLs were detected for seven yield and yield-related traits using interval and composite interval mapping. Enhancing alleles at 13 (45% of these QTLs were derived from O. nivara, and enhancing alleles at all the QTLs for stem diameter and rachis diameter were derived from O. nivara. Three stem diameter QTLs, two rachis diameter QTLs and one number of secondary branches QTL identified by both Interval and composite interval mapping contributed more than 15% of the total phenotypic variance. The QTL epistasis was significant for stem diameter and plot yield. The most significant QTLs qSD7.2, qSD8.1 and qSD9.1 for stem diameter, qRD9.1 for rachis diameter and qNSB1.1 for number of secondary branches are good targets to evaluate their use in marker-assisted selection. O. nivara is a good source of novel alleles for yield related traits and reveals major effect QTLs suitable for marker-assisted selection.

Verification of “Channel-Probability Model” of Grain Yield Estimation

Directory of Open Access Journals (Sweden)

ZHENG Hong-yan

2016-07-01

Full Text Available The "channel-probability model" of grain yield estimation was verified and discussed systematically by using the grain production data from 1949 to 2014 in 16 typical counties, and 6 typical districts, and 31 provinces of China. The results showed as follows:(1Due to the geographical spatial scale was large enough, different climate zones and different meteorological conditions could compensated, and grain yield estimation error was small in the scale of nation. Therefore, it was not necessary to modify the grain yield estimation error by mirco-trend and the climate year types in the scale of nation. However, the grain yield estimation in the scale of province was located at the same of a climate zone,the scale was small, so the impact of the meteorological conditions on grain yield was less complementary than the scale of nation. While the spatial scale of districts and counties was smaller, accordingly the compensation of the impact of the meteorological conditions on grain yield was least. Therefore, it was necessary to use mrico-trend amendment and the climate year types amendment to modify the grain yield estimation in districts and counties.(2Mirco-trend modification had two formulas, generally, when the error of grain yield estimation was less than 10%, it could be modified by Y×(1-K; while the error of grain yield estimation was more than 10%, it could be modified by Y/(1+K.(3Generally, the grain estimation had 5 grades, and some had 7 grades because of large error fluctuation. The parameters modified of super-high yield year and super-low yield year must be depended on the real-time crop growth and the meteorological condition. (4By plenty of demonstration analysis, it was proved that the theory and method of "channel-probability model" was scientific and practical. In order to improve the accuracy of grain yield estimation, the parameters could be modified with micro-trend amendment and the climate year types amendment. If the

On Geometric and Algebraic Aspects of 3D Affine and Projective Structures from Perspective 2D Views

Science.gov (United States)

1993-07-01

June 1992. an ideal lint (has no image ,n /th rteal plane) and [5] O.D. Faugeras. Q.T. Luong, and S.J. Maybank . uhich maps non-collhnearpoints A. B.C...projection for tire. Italy, .lune 1992. any giei aftin( transformation of the plane. [6 O.D. Faugeras and S. Maybank . Motion from point matches

Eesti nüüdistants näitas taset / Margit Tõnson

Index Scriptorium Estoniae

Tõnson, Margit, 1978-

2004-01-01

26.-28. märtsini toimunud festivalist "Uus tants 6", kus astusid üles ZUGA, K. Essenson, K. Juurak, Fine 5, tantsuteater Zick, E. Lints. K. Lindal, J. Savolainen, T. Jansen, O. Titovaja, R. Stepanov. Arvamusi avaldavad ka festivali külastanud lääne kuraatorid D. Van Laeken, M. Hochmuth ja K. Kwanten

A theoretical evaluation of growth yields of yeasts

NARCIS (Netherlands)

Verduyn, C.; Stouthamer, A.H.; Scheffers, W.A.; Van Dijken, J.P.

1991-01-01

Growth yields of Saccharomyces cerevisiae and Candida utilis in carbon-limited chemostat cultures were evaluated. The yields on ethanol and acetate were much lower in S. cerevisiae, in line with earlier reports that site I phosphorylation is absent in this yeast. However, during aerobic growth on

Statistical modelling and deconvolution of yield meter data

DEFF Research Database (Denmark)

Tøgersen, Frede Aakmann; Waagepetersen, Rasmus Plenge

2004-01-01

and an impulse response function. This results in an unusual spatial covariance structure (depending on the driving pattern of the combine harverster) for the yield monitoring system data. Parameters of the impulse response function and the spatial covariance function of the yield are estimated using maximum...

Respirometric assessment of storage yield for different substrates

DEFF Research Database (Denmark)

Karahan-Gül, Ö; Artan, N.; Orhon, D.

2002-01-01

A new procedure has been defined for the respirometric assessment of bacterial storage yield as defined in the Activated Sludge Model No.3. The procedure was used to determine the storage yield, YSTO, associated with acetate, glucose and domestic sewage, together with mixtures of acetate/glucose ...

interrelationships between grain yield and other physiological traits

African Journals Online (AJOL)

Prof. Adipala Ekwamu

Combined analysis of variance, cluster analysis and genotype-by- ... all phenological and morphological traits, except grain yield and associated yield components. ... egg, and other protein-rich foods (Alghali, 1991). ... systematic modelling approach. ... MD IT98 K -132 – 3 .... traits based on Principal Component axes (PC)1.

PATH COEFFICIENT ANALYSIS OF SEVERAL COMPONENTS OIL YIELD IN SUNFLOWER (HELIANTHUS ANNUUS L.

Directory of Open Access Journals (Sweden)

A. MIjić

2006-06-01

Full Text Available The objective of investigation was to analyse oil yield components and their relations by simple coefficient correlations as well as direct and indirect effects to oil yield by path analysis. Twenty-four sunflower hybrids were included in the investigation and their seven traits (plant height, head diameter, 1000 seed weight, hec- tolitar mass, grain yield, oil content and oil yield. Very strong positive correlation was estimated between grain yield and oil yield, strong positive correlation between hectolitar mass and oil yield, and middle corre- lation among oil yield and: 1000 seed weight, plaint height and oil content. There was no correlation between grain yields and oil content. Grain yield showed the strongest effect to oil yield. Oil content had lower effect to oil yield. Other traits showed no significant effect to oil yield, and their effect to oil yield was covered by indirect effect of grain yield.

Structure-process-yield interrelations in nanocrystalline cellulose extraction

Energy Technology Data Exchange (ETDEWEB)

Hamad, W.Y.; Hu, T.Q. [FPInnovations, Vancouver, BC (Canada). Paprican Div.

2010-06-15

An understanding of the effect of hydrolysis conditions on yields of extracted water-insoluble cellulose materials is needed in order to understand the full potential of the extracted materials and the extent of their applications. This study provided a detailed analysis of the extraction of highly crystalline water-insoluble cellulose nanomaterials from commercial bleached kraft pulps using a sulfuric acid hydrolysis process. The process-yield-structure interrelations of the extracted materials were evaluated. The reproducibility of the hydrolysis process was evaluated, and methods of optimizing the yield of the extracted nanomaterials were explored. A Ruland-Rietveld analysis was used to resolve X-ray diffraction patterns and characterize crystallite size, crystalline and amorphous areas, and to determine the crystallinity of the extracted materials. The study showed that sulfation determines the yield of the materials and imparts the unique solid-state characteristics of the nanomaterials. The nanomaterials possessed iridescent patterns typical of chiral nematic materials. 27 refs., 3 tabs., 7 figs.

Free-ion yield for tetramethylsilane and tetramethylgermanium

International Nuclear Information System (INIS)

Hoshi, Y.; Higuchi, M.; Iso, H.; Sakamoto, M.; Ooyama, K.; Kikuchi, R.; Miyano, K.

1993-01-01

In high energy physics experiments, calorimeters are used to measure the total energy dissipated by the primary particles produced from high energy collisions. In one type of calorimeter, ionization chambers filled with liquid argon are used. The necessity of a cryostat in many cases prevents a compact chamber design. Hence, it is very desirable to have liquid ionization chambers operating at room temperature. From this view point, hydrocarbon liquids are intensively investigated as calorimeter media in high energy physics experiments. TMS and TMG are promising liquid materials because they have the properties of a large electron drift velocity and a large free-ion yield. The free-ion yield determines the sensitivity of the chamber and amplifier system to ionizing particles. Here, free-ion yields from 207 Bi conversion electrons were measured as a function of applied electric field in an ionization chamber filled with tetramethylsilane (TMS) or tetramethylgermanium (TMG), which were purified by simple methods. Also, the mean thermalization length of electrons liberated in the liquid was calculated by fitting a Gaussian form for the distribution function. The total free-ion yield and thermalization length in TMS and TMG were obtained to be 3.1 ± 0.3, 3.5 ± 0.2 and 191 ± 12 angstrom, respectively, including the impurity effect in liquid

High yielding rice mutants for West Bengal

International Nuclear Information System (INIS)

Debnath, A.R.; Sen, S.

1980-01-01

Four high yielding mutants with specific genetic corrections of the simply inherited characters were developed from IR-8 through X-irradiation. Recurrent selections of the promising isolates were made under diverse agro-climatic conditions in Winter and Summer seasons of West Bengal. The isolates CNM 6 and CNM 25 belonging to early maturity group and CNM 20 and CNM 31, to mid-early maturity group were finally selected at X 5 generation on the basis of their resistance qualities, maturity period and grain yield. They were evaluated upto X 10 qeneration at multi-locations as Pre-release and Minikit Varieties at State level. They were also placed at the National Screening Nursery (NSN) for screening against multiple diseases and pests at the National level. CNM 6 is reported to be promising in IRTP nurseries. It is reported that CNM 25 (IET 5646) ranked 2nd on the basis of average grain yield, CNM 20 (IET 5937) and CNM 31 (IET 5936) were resistant to diseases and with yield comparable to Jaya. These four productive mutants of superior types are widely accepted. CNM 6 is recommended for cultivation in Bankura and Birbhum districts and CNM 25 and CNM 31 in the different agro-climatic zones of West Bengal. (author)

Wheat-yield response to irrigation and nitrogen

International Nuclear Information System (INIS)

Kirda, C.; Derici, R.; Kanber, R.; Yazar, A.; Koc, M.; Barutcular, C.

2000-01-01

Wheat-yield responses to the application of different rates of N fertilizer, under irrigated and rainfed conditions, were evaluated over four growing seasons. Nitrogen applied at tillering was utilized more effectively with proportionately less residual in the soil compared to that applied at planting. Subsequent crops of maize or cotton were positively affected by residual fertilizer N. Volatilization and leaching losses of applied N were small. Crop-water consumption showed strong positive associations with N rate. No wheat-grain-yield benefits accrued from irrigation, although straw yields were increased. Tiller production increased with N-fertilizer usage, however, tiller survival decreased at high N and was highest at 160 kg N ha -1 . Higher N rates produced higher stomatal conductance, increased rates of CO 2 assimilation and higher water-use efficiency. The CERES-Wheat growth-simulation model predicted rather closely the progress of dry-matter production, leaf area index, seasonal evapotranspiration, phenological development and of many other plant-growth attributes. The data indicated that the rate of 160 kg N ha -1 , which is commonly used by the farmers of the region, is acceptable, not only for optimum grain yields but also to minimize the risks of leaching NO 3 - to groundwater. (author)

Association between Empirically Estimated Monsoon Dynamics and Other Weather Factors and Historical Tea Yields in China: Results from a Yield Response Model

Directory of Open Access Journals (Sweden)

Rebecca Boehm

2016-04-01

Full Text Available Farmers in China’s tea-growing regions report that monsoon dynamics and other weather factors are changing and that this is affecting tea harvest decisions. To assess the effect of climate change on tea production in China, this study uses historical weather and production data from 1980 to 2011 to construct a yield response model that estimates the partial effect of weather factors on tea yields in China, with a specific focus on East Asian Monsoon dynamics. Tea (Camellia sinensis (L. Kunze has not been studied using these methods even though it is an important crop for human nutrition and the economic well-being of rural communities in many countries. Previous studies have approximated the monsoon period using historical average onset and retreat dates, which we believe limits our understanding of how changing monsoon patterns affect crop productivity. In our analysis, we instead estimate the monsoon season across China’s tea growing regions empirically by identifying the unknown breakpoints in the year-by-province cumulative precipitation. We find that a 1% increase in the monsoon retreat date is associated with 0.481%–0.535% reduction in tea yield. In the previous year, we also find that a 1% increase in the date of the monsoon retreat is associated with a 0.604% decrease in tea yields. For precipitation, we find that a 1% increase in average daily precipitation occurring during the monsoon period is associated with a 0.184%–0.262% reduction in tea yields. In addition, our models show that 1% increase in the average daily monsoon precipitation from the previous growing season is associated with 0.258%–0.327% decline in yields. We also find that a 1% decrease in solar radiation in the previous growing season is associated with 0.554%-0.864% decrease in tea yields. These findings suggest the need for adaptive management and harvesting strategies given climate change projections and the known negative association between excess

Effects of Irrigation and Nitrogen Application Rates on Yield and Yield Components of Corn, Sesame and Sugar beet in Mashhad Climatic Condition

Directory of Open Access Journals (Sweden)

R Heydari Pour

2015-07-01

Full Text Available In many crops, incorrect management of nitrogen and water is one of the most important factors in the resources productivity such as water and nitrogen. In order to evaluate the effects of different nitrogen levels (zero, 50, 100 and 150 kg ha-1 and irrigation application rates (100, 75 and 50% of water requirement per species on corn, sesame and sugar beet, three separate experiments was conducted in Agricultural Research Station of Ferdowsi University of Mashhad, Iran, in 2009-2010 growing season. Three separate experiments were arranged by strip plots in randomized complete block design, with three replications. The results showed that effect of irrigation application rates on biological yield and grain number per ear and interaction effects of water × nitrogen on plant height, 100 grain weight and grain yield of corn was significant. With decreasing irrigation over 25 % water requirements, the highest grain yield (4.93 ton ha-1 in corn observed by applying nitrogen equal to 50 kg.ha-1. In addition, the highest maize yield (9.41 ton.ha-1 in mentioned was obtained by supplying 100 % water requirements. Effects of Irrigation levels on plant height and the interaction effects of water × nitrogen on 1000 grain weight in sesame was significant. Under no water stress, the highest grain yield (1.22 ton ha-1 in sesame was obtained with applying 50kg nitrogen per ha. With supplying 75% water requirements plus 50 kg nitrogen per hactar, maximum yield of sesame (820 kg ha-1 was obtained. Results of this study indicated that interaction between studied factors had insignificant effect on economic and biological yield in sugar beet. With supplying 25% water requirements plus 50 kg nitrogen per ha, maximum yield of sugar beet (58.37 ton ha-1 was achieved. It seems that suitable nitrogen management can be considered as approach in optimize the water consuming.

Closing Yield Gaps: How Sustainable Can We Be?

Science.gov (United States)

Pradhan, Prajal; Fischer, Günther; van Velthuizen, Harrij; Reusser, Dominik E.; Kropp, Juergen P.

2015-01-01

Global food production needs to be increased by 60–110% between 2005 and 2050 to meet growing food and feed demand. Intensification and/or expansion of agriculture are the two main options available to meet the growing crop demands. Land conversion to expand cultivated land increases GHG emissions and impacts biodiversity and ecosystem services. Closing yield gaps to attain potential yields may be a viable option to increase the global crop production. Traditional methods of agricultural intensification often have negative externalities. Therefore, there is a need to explore location-specific methods of sustainable agricultural intensification. We identified regions where the achievement of potential crop calorie production on currently cultivated land will meet the present and future food demand based on scenario analyses considering population growth and changes in dietary habits. By closing yield gaps in the current irrigated and rain-fed cultivated land, about 24% and 80% more crop calories can respectively be produced compared to 2000. Most countries will reach food self-sufficiency or improve their current food self-sufficiency levels if potential crop production levels are achieved. As a novel approach, we defined specific input and agricultural management strategies required to achieve the potential production by overcoming biophysical and socioeconomic constraints causing yield gaps. The management strategies include: fertilizers, pesticides, advanced soil management, land improvement, management strategies coping with weather induced yield variability, and improving market accessibility. Finally, we estimated the required fertilizers (N, P2O5, and K2O) to attain the potential yields. Globally, N-fertilizer application needs to increase by 45–73%, P2O5-fertilizer by 22–46%, and K2O-fertilizer by 2–3 times compared to the year 2010 to attain potential crop production. The sustainability of such agricultural intensification largely depends on the way