Linear Logistic Test Modeling with R
Baghaei, Purya; Kubinger, Klaus D.
2015-01-01
The present paper gives a general introduction to the linear logistic test model (Fischer, 1973), an extension of the Rasch model with linear constraints on item parameters, along with eRm (an R package to estimate different types of Rasch models; Mair, Hatzinger, & Mair, 2014) functions to estimate the model and interpret its parameters. The…
Q-Matrix Optimization Based on the Linear Logistic Test Model.
Ma, Lin; Green, Kelly E
This study explored optimization of item-attribute matrices with the linear logistic test model (Fischer, 1973), with optimal models explaining more variance in item difficulty due to identified item attributes. Data were 8th-grade mathematics test item responses of two TIMSS 2007 booklets. The study investigated three categories of attributes (content, cognitive process, and comprehensive cognitive process) at two grain levels (larger, smaller) and also compared results with random attribute matrices. The proposed attributes accounted for most of the variance in item difficulty for two assessment booklets (81% and 65%). The variance explained by the content attributes was very small (13% to 31%), less than variance explained by the comprehensive cognitive process attributes which explained much more variance than the content and cognitive process attributes. The variances explained by the grain level were similar to each other. However, the attributes did not predict the item difficulties of two assessment booklets equally.
Evaluating an Automated Number Series Item Generator Using Linear Logistic Test Models
Bao Sheng Loe
2018-04-01
Full Text Available This study investigates the item properties of a newly developed Automatic Number Series Item Generator (ANSIG. The foundation of the ANSIG is based on five hypothesised cognitive operators. Thirteen item models were developed using the numGen R package and eleven were evaluated in this study. The 16-item ICAR (International Cognitive Ability Resource1 short form ability test was used to evaluate construct validity. The Rasch Model and two Linear Logistic Test Model(s (LLTM were employed to estimate and predict the item parameters. Results indicate that a single factor determines the performance on tests composed of items generated by the ANSIG. Under the LLTM approach, all the cognitive operators were significant predictors of item difficulty. Moderate to high correlations were evident between the number series items and the ICAR test scores, with high correlation found for the ICAR Letter-Numeric-Series type items, suggesting adequate nomothetic span. Extended cognitive research is, nevertheless, essential for the automatic generation of an item pool with predictable psychometric properties.
HERBERT POINSTINGL
2009-06-01
Full Text Available Based on the demand for new verbal reasoning tests to enrich psychological test inventory, a pilot version of a new test was analysed: the 'Family Relation Reasoning Test' (FRRT; Poinstingl, Kubinger, Skoda & Schechtner, forthcoming, in which several basic cognitive operations (logical rules have been embedded/implemented. Given family relationships of varying complexity embedded in short stories, testees had to logically conclude the correct relationship between two individuals within a family. Using empirical data, the linear logistic test model (LLTM; Fischer, 1972, a special case of the Rasch model, was used to test the construct validity of the test: The hypothetically assumed basic cognitive operations had to explain the Rasch model's item difficulty parameters. After being shaped in LLTM's matrices of weights ((qij, none of these operations were corroborated by means of the Andersen's Likelihood Ratio Test.
Chandler, T L; Pralle, R S; Dórea, J R R; Poock, S E; Oetzel, G R; Fourdraine, R H; White, H M
2018-03-01
Although cowside testing strategies for diagnosing hyperketonemia (HYK) are available, many are labor intensive and costly, and some lack sufficient accuracy. Predicting milk ketone bodies by Fourier transform infrared spectrometry during routine milk sampling may offer a more practical monitoring strategy. The objectives of this study were to (1) develop linear and logistic regression models using all available test-day milk and performance variables for predicting HYK and (2) compare prediction methods (Fourier transform infrared milk ketone bodies, linear regression models, and logistic regression models) to determine which is the most predictive of HYK. Given the data available, a secondary objective was to evaluate differences in test-day milk and performance variables (continuous measurements) between Holsteins and Jerseys and between cows with or without HYK within breed. Blood samples were collected on the same day as milk sampling from 658 Holstein and 468 Jersey cows between 5 and 20 d in milk (DIM). Diagnosis of HYK was at a serum β-hydroxybutyrate (BHB) concentration ≥1.2 mmol/L. Concentrations of milk BHB and acetone were predicted by Fourier transform infrared spectrometry (Foss Analytical, Hillerød, Denmark). Thresholds of milk BHB and acetone were tested for diagnostic accuracy, and logistic models were built from continuous variables to predict HYK in primiparous and multiparous cows within breed. Linear models were constructed from continuous variables for primiparous and multiparous cows within breed that were 5 to 11 DIM or 12 to 20 DIM. Milk ketone body thresholds diagnosed HYK with 64.0 to 92.9% accuracy in Holsteins and 59.1 to 86.6% accuracy in Jerseys. Logistic models predicted HYK with 82.6 to 97.3% accuracy. Internally cross-validated multiple linear regression models diagnosed HYK of Holstein cows with 97.8% accuracy for primiparous and 83.3% accuracy for multiparous cows. Accuracy of Jersey models was 81.3% in primiparous and 83
Linear Estimation of Standard Deviation of Logistic Distribution ...
The paper presents a theoretical method based on order statistics and a FORTRAN program for computing the variance and relative efficiencies of the standard deviation of the logistic population with respect to the Cramer-Rao lower variance bound and the best linear unbiased estimators (BLUE\\'s) when the mean is ...
A fuzzy Bi-linear management model in reverse logistic chains
Tadić Danijela
2016-01-01
Full Text Available The management of the electrical and electronic waste (WEEE problem in the uncertain environment has a critical effect on the economy and environmental protection of each region. The considered problem can be stated as a fuzzy non-convex optimization problem with linear objective function and a set of linear and non-linear constraints. The original problem is reformulated by using linear relaxation into a fuzzy linear programming problem. The fuzzy rating of collecting point capacities and fix costs of recycling centers are modeled by triangular fuzzy numbers. The optimal solution of the reformulation model is found by using optimality concept. The proposed model is verified through an illustrative example with real-life data. The obtained results represent an input for future research which should include a good benchmark base for tested reverse logistic chains and their continuous improvement. [Projekat Ministarstva nauke Republike Srbije, br. 035033: Sustainable development technology and equipment for the recycling of motor vehicles
Tripepi, Giovanni; Jager, Kitty J.; Stel, Vianda S.; Dekker, Friedo W.; Zoccali, Carmine
2011-01-01
Because of some limitations of stratification methods, epidemiologists frequently use multiple linear and logistic regression analyses to address specific epidemiological questions. If the dependent variable is a continuous one (for example, systolic pressure and serum creatinine), the researcher
Linear Synchronous Motor Repeatability Tests
Ward, C.R.
2002-01-01
A cart system using linear synchronous motors was being considered for the Plutonium Immobilization Plant (PIP). One of the applications in the PIP was the movement of a stack of furnace trays, filled with the waste form (pucks) from a stacking/unstacking station to several bottom loaded furnaces. A system was ordered to perform this function in the PIP Ceramic Prototype Test Facility (CPTF). This system was installed and started up in SRTC prior to being installed in the CPTF. The PIP was suspended and then canceled after the linear synchronous motor system was started up. This system was used to determine repeatability of a linear synchronous motor cart system for the Modern Pit Facility
Test accelerator for linear collider
Takeda, S.; Akai, K.; Akemoto, M.; Araki, S.; Hayano, H.; Hugo, T.; Ishihara, N.; Kawamoto, T.; Kimura, Y.; Kobayashi, H.; Kubo, T.; Kurokawa, S.; Matsumoto, H.; Mizuno, H.; Odagiri, J.; Otake, Y.; Sakai, H.; Shidara, T.; Shintake, T.; Suetake, M.; Takashima, T.; Takata, K.; Takeuchi, Y.; Urakawa, J.; Yamamoto, N.; Yokoya, K.; Yoshida, M.; Yoshioka, M.; Yamaoka, Y.
1989-01-01
KEK has proposed to build Test Accelerator Facility (TAF) capable of producing a 2.5 GeV electron beam for the purpose of stimulating R ampersand D for linear collider in TeV region. The TAF consists of a 1.5 GeV S-band linear accelerator, 1.5 GeV damping ring and 1.0 GeV X-band linear accelerator. The TAF project will be carried forward in three phases. Through Phase-I and Phase-II, the S-band and X-band linacs will be constructed, and in Phase-III, the damping ring will be completed. The construction of TAF Phase-I has started, and the 0.2 GeV S-band injector linac has been almost completed. The Phase-I linac is composed of a 240 keV electron gun, subharmonic bunchers, prebunchers and traveling buncher followed by high-gradient accelerating structures. The SLAC 5045 klystrons are driven at 450 kV in order to obtain the rf-power of 100 MW in a 1 μs pulse duration. The rf-power from a pair of klystrons are combined into an accelerating structure. The accelerating gradient up to 100 MeV/m will be obtained in a 0.6 m long structure. 5 refs., 3 figs., 2 tabs
Schörgendorfer, Angela; Branscum, Adam J; Hanson, Timothy E
2013-06-01
Logistic regression is a popular tool for risk analysis in medical and population health science. With continuous response data, it is common to create a dichotomous outcome for logistic regression analysis by specifying a threshold for positivity. Fitting a linear regression to the nondichotomized response variable assuming a logistic sampling model for the data has been empirically shown to yield more efficient estimates of odds ratios than ordinary logistic regression of the dichotomized endpoint. We illustrate that risk inference is not robust to departures from the parametric logistic distribution. Moreover, the model assumption of proportional odds is generally not satisfied when the condition of a logistic distribution for the data is violated, leading to biased inference from a parametric logistic analysis. We develop novel Bayesian semiparametric methodology for testing goodness of fit of parametric logistic regression with continuous measurement data. The testing procedures hold for any cutoff threshold and our approach simultaneously provides the ability to perform semiparametric risk estimation. Bayes factors are calculated using the Savage-Dickey ratio for testing the null hypothesis of logistic regression versus a semiparametric generalization. We propose a fully Bayesian and a computationally efficient empirical Bayesian approach to testing, and we present methods for semiparametric estimation of risks, relative risks, and odds ratios when parametric logistic regression fails. Theoretical results establish the consistency of the empirical Bayes test. Results from simulated data show that the proposed approach provides accurate inference irrespective of whether parametric assumptions hold or not. Evaluation of risk factors for obesity shows that different inferences are derived from an analysis of a real data set when deviations from a logistic distribution are permissible in a flexible semiparametric framework. © 2013, The International Biometric
Neck-focused panic attacks among Cambodian refugees; a logistic and linear regression analysis.
Hinton, Devon E; Chhean, Dara; Pich, Vuth; Um, Khin; Fama, Jeanne M; Pollack, Mark H
2006-01-01
Consecutive Cambodian refugees attending a psychiatric clinic were assessed for the presence and severity of current--i.e., at least one episode in the last month--neck-focused panic. Among the whole sample (N=130), in a logistic regression analysis, the Anxiety Sensitivity Index (ASI; odds ratio=3.70) and the Clinician-Administered PTSD Scale (CAPS; odds ratio=2.61) significantly predicted the presence of current neck panic (NP). Among the neck panic patients (N=60), in the linear regression analysis, NP severity was significantly predicted by NP-associated flashbacks (beta=.42), NP-associated catastrophic cognitions (beta=.22), and CAPS score (beta=.28). Further analysis revealed the effect of the CAPS score to be significantly mediated (Sobel test [Baron, R. M., & Kenny, D. A. (1986). The moderator-mediator variable distinction in social psychological research: conceptual, strategic, and statistical considerations. Journal of Personality and Social Psychology, 51, 1173-1182]) by both NP-associated flashbacks and catastrophic cognitions. In the care of traumatized Cambodian refugees, NP severity, as well as NP-associated flashbacks and catastrophic cognitions, should be specifically assessed and treated.
Inverse estimation of multiple muscle activations based on linear logistic regression.
Sekiya, Masashi; Tsuji, Toshiaki
2017-07-01
This study deals with a technology to estimate the muscle activity from the movement data using a statistical model. A linear regression (LR) model and artificial neural networks (ANN) have been known as statistical models for such use. Although ANN has a high estimation capability, it is often in the clinical application that the lack of data amount leads to performance deterioration. On the other hand, the LR model has a limitation in generalization performance. We therefore propose a muscle activity estimation method to improve the generalization performance through the use of linear logistic regression model. The proposed method was compared with the LR model and ANN in the verification experiment with 7 participants. As a result, the proposed method showed better generalization performance than the conventional methods in various tasks.
Performance test of 100 W linear compressor
Ko, J; Ko, D. Y.; Park, S. J.; Kim, H. B.; Hong, Y. J.; Yeom, H. K. [Korea Institute of Machinery and Materials, Daejeon(Korea, Republic of)
2013-09-15
In this paper, we present test results of developed 100 W class linear compressor for Stirling-type pulse tube refrigerator. The fabricated linear compressor has dual-opposed configuration, free piston and moving magnet type linear motor. Power transfer, efficiency and required pressure waveform are predicted with designed and measured specifications. In experiments, room temperature test with flow impedance is conducted to evaluate performance of developed linear compressor. Flow impedance is loaded to compressor with metering valve for flow resistance, inertance tube for flow inertance and buffer volumes for flow compliance. Several operating parameters such as input voltage, current, piston displacement and pressure wave are measured for various operating frequency and fixed input current level. Behaviors of dynamics and performance of linear compressor as varying flow impedance are discussed with measured experimental results. The developed linear compressor shows 124 W of input power, 86 % of motor efficiency and 60 % of compressor efficiency at its resonant operating condition.
Estimating traffic volume on Wyoming low volume roads using linear and logistic regression methods
Dick Apronti
2016-12-01
Full Text Available Traffic volume is an important parameter in most transportation planning applications. Low volume roads make up about 69% of road miles in the United States. Estimating traffic on the low volume roads is a cost-effective alternative to taking traffic counts. This is because traditional traffic counts are expensive and impractical for low priority roads. The purpose of this paper is to present the development of two alternative means of cost-effectively estimating traffic volumes for low volume roads in Wyoming and to make recommendations for their implementation. The study methodology involves reviewing existing studies, identifying data sources, and carrying out the model development. The utility of the models developed were then verified by comparing actual traffic volumes to those predicted by the model. The study resulted in two regression models that are inexpensive and easy to implement. The first regression model was a linear regression model that utilized pavement type, access to highways, predominant land use types, and population to estimate traffic volume. In verifying the model, an R2 value of 0.64 and a root mean square error of 73.4% were obtained. The second model was a logistic regression model that identified the level of traffic on roads using five thresholds or levels. The logistic regression model was verified by estimating traffic volume thresholds and determining the percentage of roads that were accurately classified as belonging to the given thresholds. For the five thresholds, the percentage of roads classified correctly ranged from 79% to 88%. In conclusion, the verification of the models indicated both model types to be useful for accurate and cost-effective estimation of traffic volumes for low volume Wyoming roads. The models developed were recommended for use in traffic volume estimations for low volume roads in pavement management and environmental impact assessment studies.
Shayan, Zahra; Mohammad Gholi Mezerji, Naser; Shayan, Leila; Naseri, Parisa
2015-11-03
Logistic regression (LR) and linear discriminant analysis (LDA) are two popular statistical models for prediction of group membership. Although they are very similar, the LDA makes more assumptions about the data. When categorical and continuous variables used simultaneously, the optimal choice between the two models is questionable. In most studies, classification error (CE) is used to discriminate between subjects in several groups, but this index is not suitable to predict the accuracy of the outcome. The present study compared LR and LDA models using classification indices. This cross-sectional study selected 243 cancer patients. Sample sets of different sizes (n = 50, 100, 150, 200, 220) were randomly selected and the CE, B, and Q classification indices were calculated by the LR and LDA models. CE revealed the a lack of superiority for one model over the other, but the results showed that LR performed better than LDA for the B and Q indices in all situations. No significant effect for sample size on CE was noted for selection of an optimal model. Assessment of the accuracy of prediction of real data indicated that the B and Q indices are appropriate for selection of an optimal model. The results of this study showed that LR performs better in some cases and LDA in others when based on CE. The CE index is not appropriate for classification, although the B and Q indices performed better and offered more efficient criteria for comparison and discrimination between groups.
Statistical Tests for Mixed Linear Models
Khuri, André I; Sinha, Bimal K
2011-01-01
An advanced discussion of linear models with mixed or random effects. In recent years a breakthrough has occurred in our ability to draw inferences from exact and optimum tests of variance component models, generating much research activity that relies on linear models with mixed and random effects. This volume covers the most important research of the past decade as well as the latest developments in hypothesis testing. It compiles all currently available results in the area of exact and optimum tests for variance component models and offers the only comprehensive treatment for these models a
Test facilities for future linear colliders
Ruth, R.D.
1995-12-01
During the past several years there has been a tremendous amount of progress on Linear Collider technology world wide. This research has led to the construction of the test facilities described in this report. Some of the facilities will be complete as early as the end of 1996, while others will be finishing up around the end 1997. Even now there are extensive tests ongoing for the enabling technologies for all of the test facilities. At the same time the Linear Collider designs are quite mature now and the SLC is providing the key experience base that can only come from a working collider. All this taken together indicates that the technology and accelerator physics will be ready for a future Linear Collider project to begin in the last half of the 1990s
Cold Regions Logistic Supportability Testing of Armament and Individual Weapons
1983-10-07
CHECKLIST 1. Have test data been collected, recorded, and presented in accordance with this TOP? YES NO Comment : 2. Have all data collected been reviewed...for correctness and completeness? YES NO Comment : 3. Were the facilities, test equipment, instrumentation, and support accommodations adequate to...test results compromised in any way due to test performance procedures? YES NO . Comment : 6. Were the test results compromised in any way due to test
Cold Regions Logistic Supportability Testing of Missiles and Rocket Systems.
1984-10-26
006 APPENDIX B - POST-TEST CHECKLIST 1. Have test data been collected, recorded, and presented in accordance with this TOP? YES NO Comment : 2. Have all...data collected been reviewed for correctness and completeness? YES_ NO Comment : 3. Were the facilities, test equipment, instrumentation, and support...YES NO Comment : 5. Were the test results compromised in any way due to test performance procedures? YES_ NO Comment : 6. Were the test results
Fan, Xitao; Wang, Lin
The Monte Carlo study compared the performance of predictive discriminant analysis (PDA) and that of logistic regression (LR) for the two-group classification problem. Prior probabilities were used for classification, but the cost of misclassification was assumed to be equal. The study used a fully crossed three-factor experimental design (with…
Power and Sample Size Calculations for Logistic Regression Tests for Differential Item Functioning
Li, Zhushan
2014-01-01
Logistic regression is a popular method for detecting uniform and nonuniform differential item functioning (DIF) effects. Theoretical formulas for the power and sample size calculations are derived for likelihood ratio tests and Wald tests based on the asymptotic distribution of the maximum likelihood estimators for the logistic regression model.…
The CERN linear collider test facility (CTF)
Baconnier, Y.; Battisti, S.; Bossart, R.; Delahaye, J.P.; Geissler, K.K.; Godot, J.C.; Huebner, K.; Madsen, J.H.B.; Potier, J.P.; Riche, A.J.; Sladen, J.; Suberlucq, G.; Wilson, I.; Wuensch, W.
1992-01-01
The CTF (Collider Test Facility) was brought into service last year. The 3 GHz gun produced a beam of 3 MeV/c which was accelerated to 40 MeV/c. This beam, passing a prototype CLIC (linear collider) structure, generated a sizeable amount of 30 GHz power. This paper describes the results and experience with the gun driven by a 8 ns long laser pulse and its CsI photo cathode, the beam behaviour, the beam diagnostics in particular with the bunch measurements by Cerenkov or transition radiation light and streak camera, the photo cathode research, and the beam dynamics studies on space charge effects. (Author)4 figs., tab., 6 refs
The Next Linear Collider Test Accelerator
Ruth, R.D.; Adolphsen, C.; Bane, K.
1993-04-01
During the past several years, there has been tremendous progress the development of the RF system and accelerating structures for a Next Linear Collider (NLC). Developments include high-power klystrons, RF pulse compression systems and damped/detuned accelerator structures to reduce wakefields. In order to integrate these separate development efforts into an actual X-band accelerator capable of accelerating the electron beams necessary for an NLC, we are building an NLC Test Accelerator (NLCTA). The goal of the NLCTA is to bring together all elements of the entire accelerating system by constructing and reliably operating an engineered model of a high-gradient linac suitable for the NLC. The NLCTA will serve as a testbed as the design of the NLC evolves. In addition to testing the RF acceleration system, the NLCTA is designed to address many questions related to the dynamics of the beam during acceleration. In this paper, we will report oil the status of the design, component development, and construction of the NLC Test Accelerator
Ren, Y Y; Zhou, L C; Yang, L; Liu, P Y; Zhao, B W; Liu, H X
2016-09-01
The paper highlights the use of the logistic regression (LR) method in the construction of acceptable statistically significant, robust and predictive models for the classification of chemicals according to their aquatic toxic modes of action. Essentials accounting for a reliable model were all considered carefully. The model predictors were selected by stepwise forward discriminant analysis (LDA) from a combined pool of experimental data and chemical structure-based descriptors calculated by the CODESSA and DRAGON software packages. Model predictive ability was validated both internally and externally. The applicability domain was checked by the leverage approach to verify prediction reliability. The obtained models are simple and easy to interpret. In general, LR performs much better than LDA and seems to be more attractive for the prediction of the more toxic compounds, i.e. compounds that exhibit excess toxicity versus non-polar narcotic compounds and more reactive compounds versus less reactive compounds. In addition, model fit and regression diagnostics was done through the influence plot which reflects the hat-values, studentized residuals, and Cook's distance statistics of each sample. Overdispersion was also checked for the LR model. The relationships between the descriptors and the aquatic toxic behaviour of compounds are also discussed.
Spatiotemporal chaos in mixed linear-nonlinear two-dimensional coupled logistic map lattice
Zhang, Ying-Qian; He, Yi; Wang, Xing-Yuan
2018-01-01
We investigate a new spatiotemporal dynamics with mixing degrees of nonlinear chaotic maps for spatial coupling connections based on 2DCML. Here, the coupling methods are including with linear neighborhood coupling and the nonlinear chaotic map coupling of lattices, and the former 2DCML system is only a special case in the proposed system. In this paper the criteria such Kolmogorov-Sinai entropy density and universality, bifurcation diagrams, space-amplitude and snapshot pattern diagrams are provided in order to investigate the chaotic behaviors of the proposed system. Furthermore, we also investigate the parameter ranges of the proposed system which holds those features in comparisons with those of the 2DCML system and the MLNCML system. Theoretical analysis and computer simulation indicate that the proposed system contains features such as the higher percentage of lattices in chaotic behaviors for most of parameters, less periodic windows in bifurcation diagrams and the larger range of parameters for chaotic behaviors, which is more suitable for cryptography.
Hong, H.; Zhu, A. X.
2017-12-01
Climate change is a common phenomenon and it is very serious all over the world. The intensification of rainfall extremes with climate change is of key importance to society and then it may induce a large impact through landslides. This paper presents GIS-based new ensemble data mining techniques that weight-of-evidence, logistic model tree, linear and quadratic discriminant for landslide spatial modelling. This research was applied in Anfu County, which is a landslide-prone area in Jiangxi Province, China. According to a literature review and research the study area, we select the landslide influencing factor and their maps were digitized in a GIS environment. These landslide influencing factors are the altitude, plan curvature, profile curvature, slope degree, slope aspect, topographic wetness index (TWI), Stream Power Index (SPI), Topographic Wetness Index (SPI), distance to faults, distance to rivers, distance to roads, soil, lithology, normalized difference vegetation index and land use. According to historical information of individual landslide events, interpretation of the aerial photographs, and field surveys supported by the government of Jiangxi Meteorological Bureau of China, 367 landslides were identified in the study area. The landslide locations were divided into two subsets, namely, training and validating (70/30), based on a random selection scheme. In this research, Pearson's correlation was used for the evaluation of the relationship between the landslides and influencing factors. In the next step, three data mining techniques combined with the weight-of-evidence, logistic model tree, linear and quadratic discriminant, were used for the landslide spatial modelling and its zonation. Finally, the landslide susceptibility maps produced by the mentioned models were evaluated by the ROC curve. The results showed that the area under the curve (AUC) of all of the models was > 0.80. At the same time, the highest AUC value was for the linear and quadratic
Sampson, Maureen L; Gounden, Verena; van Deventer, Hendrik E; Remaley, Alan T
2016-02-01
The main drawback of the periodic analysis of quality control (QC) material is that test performance is not monitored in time periods between QC analyses, potentially leading to the reporting of faulty test results. The objective of this study was to develop a patient based QC procedure for the more timely detection of test errors. Results from a Chem-14 panel measured on the Beckman LX20 analyzer were used to develop the model. Each test result was predicted from the other 13 members of the panel by multiple regression, which resulted in correlation coefficients between the predicted and measured result of >0.7 for 8 of the 14 tests. A logistic regression model, which utilized the measured test result, the predicted test result, the day of the week and time of day, was then developed for predicting test errors. The output of the logistic regression was tallied by a daily CUSUM approach and used to predict test errors, with a fixed specificity of 90%. The mean average run length (ARL) before error detection by CUSUM-Logistic Regression (CSLR) was 20 with a mean sensitivity of 97%, which was considerably shorter than the mean ARL of 53 (sensitivity 87.5%) for a simple prediction model that only used the measured result for error detection. A CUSUM-Logistic Regression analysis of patient laboratory data can be an effective approach for the rapid and sensitive detection of clinical laboratory errors. Published by Elsevier Inc.
A Note on Three Statistical Tests in the Logistic Regression DIF Procedure
Paek, Insu
2012-01-01
Although logistic regression became one of the well-known methods in detecting differential item functioning (DIF), its three statistical tests, the Wald, likelihood ratio (LR), and score tests, which are readily available under the maximum likelihood, do not seem to be consistently distinguished in DIF literature. This paper provides a clarifying…
A test for the parameters of multiple linear regression models ...
A test for the parameters of multiple linear regression models is developed for conducting tests simultaneously on all the parameters of multiple linear regression models. The test is robust relative to the assumptions of homogeneity of variances and absence of serial correlation of the classical F-test. Under certain null and ...
Valle, Denis; Lima, Joanna M Tucker; Millar, Justin; Amratia, Punam; Haque, Ubydul
2015-11-04
Logistic regression is a statistical model widely used in cross-sectional and cohort studies to identify and quantify the effects of potential disease risk factors. However, the impact of imperfect tests on adjusted odds ratios (and thus on the identification of risk factors) is under-appreciated. The purpose of this article is to draw attention to the problem associated with modelling imperfect diagnostic tests, and propose simple Bayesian models to adequately address this issue. A systematic literature review was conducted to determine the proportion of malaria studies that appropriately accounted for false-negatives/false-positives in a logistic regression setting. Inference from the standard logistic regression was also compared with that from three proposed Bayesian models using simulations and malaria data from the western Brazilian Amazon. A systematic literature review suggests that malaria epidemiologists are largely unaware of the problem of using logistic regression to model imperfect diagnostic test results. Simulation results reveal that statistical inference can be substantially improved when using the proposed Bayesian models versus the standard logistic regression. Finally, analysis of original malaria data with one of the proposed Bayesian models reveals that microscopy sensitivity is strongly influenced by how long people have lived in the study region, and an important risk factor (i.e., participation in forest extractivism) is identified that would have been missed by standard logistic regression. Given the numerous diagnostic methods employed by malaria researchers and the ubiquitous use of logistic regression to model the results of these diagnostic tests, this paper provides critical guidelines to improve data analysis practice in the presence of misclassification error. Easy-to-use code that can be readily adapted to WinBUGS is provided, enabling straightforward implementation of the proposed Bayesian models.
Antares alignment gimbal positioner linear bearing tests
Day, R.D.; McKay, M.D.; Pierce, D.D.; Lujan, R.E.
1981-01-01
The data indicate that of the six configurations tested, the solid circular rails with either the wet or dry lubricant are superior to the other configurations. Therefore, these two will undergo additional tests. These tests will consist of (1) modifying the testing procedure to obtain a better estimation of the limits of precision; and (2) subjecting the bearings to moments more closely approximating the actual conditions they will undergo on the AGP
Yang Zhao
Full Text Available GWAS has facilitated greatly the discovery of risk SNPs associated with complex diseases. Traditional methods analyze SNP individually and are limited by low power and reproducibility since correction for multiple comparisons is necessary. Several methods have been proposed based on grouping SNPs into SNP sets using biological knowledge and/or genomic features. In this article, we compare the linear kernel machine based test (LKM and principal components analysis based approach (PCA using simulated datasets under the scenarios of 0 to 3 causal SNPs, as well as simple and complex linkage disequilibrium (LD structures of the simulated regions. Our simulation study demonstrates that both LKM and PCA can control the type I error at the significance level of 0.05. If the causal SNP is in strong LD with the genotyped SNPs, both the PCA with a small number of principal components (PCs and the LKM with kernel of linear or identical-by-state function are valid tests. However, if the LD structure is complex, such as several LD blocks in the SNP set, or when the causal SNP is not in the LD block in which most of the genotyped SNPs reside, more PCs should be included to capture the information of the causal SNP. Simulation studies also demonstrate the ability of LKM and PCA to combine information from multiple causal SNPs and to provide increased power over individual SNP analysis. We also apply LKM and PCA to analyze two SNP sets extracted from an actual GWAS dataset on non-small cell lung cancer.
Bonellie, Sandra R
2012-10-01
To illustrate the use of regression and logistic regression models to investigate changes over time in size of babies particularly in relation to social deprivation, age of the mother and smoking. Mean birthweight has been found to be increasing in many countries in recent years, but there are still a group of babies who are born with low birthweights. Population-based retrospective cohort study. Multiple linear regression and logistic regression models are used to analyse data on term 'singleton births' from Scottish hospitals between 1994-2003. Mothers who smoke are shown to give birth to lighter babies on average, a difference of approximately 0.57 Standard deviations lower (95% confidence interval. 0.55-0.58) when adjusted for sex and parity. These mothers are also more likely to have babies that are low birthweight (odds ratio 3.46, 95% confidence interval 3.30-3.63) compared with non-smokers. Low birthweight is 30% more likely where the mother lives in the most deprived areas compared with the least deprived, (odds ratio 1.30, 95% confidence interval 1.21-1.40). Smoking during pregnancy is shown to have a detrimental effect on the size of infants at birth. This effect explains some, though not all, of the observed socioeconomic birthweight. It also explains much of the observed birthweight differences by the age of the mother. Identifying mothers at greater risk of having a low birthweight baby as important implications for the care and advice this group receives. © 2012 Blackwell Publishing Ltd.
Comparison of IRT Likelihood Ratio Test and Logistic Regression DIF Detection Procedures
Atar, Burcu; Kamata, Akihito
2011-01-01
The Type I error rates and the power of IRT likelihood ratio test and cumulative logit ordinal logistic regression procedures in detecting differential item functioning (DIF) for polytomously scored items were investigated in this Monte Carlo simulation study. For this purpose, 54 simulation conditions (combinations of 3 sample sizes, 2 sample…
Material testing in a linear theta pinch
Alani, R.; Azodi, H.; Naraghi, M.; Safaii, B.; Torabi-Fard, A.
1983-01-01
The interaction of stainless steel 316 and Inconel 625 alloys has been investigated with a thermonuclear-like plasma, n = 10 16 cm -3 and Tsub(i) = 1 keV, generated in the Alvand I linear theta pinch. The average power flux is 10 7 W/cm 2 and the interaction time nearly one μs. A theoretical analysis based on the formation of an observed impurity layer near the material, has been used to determine the properties of the impurity layer and the extent of the damage on the material. Although arcing has been observed, the dominant damage mechanism has been assessed to be due to evaporation. Exposure to single shots has produced very heavily defective areas and even surface cracks on the SS 316 sample, but no cracks were observed on Inconel 625 after exposure to even 18 shots. On the basis of temperature rise and evaporation a comparison is made among materials exposed to plasmas of a theta pinch, shock tube, present generation tokamak and an anticipated tokamak reactor. (orig.)
Test Stand for Linear Induction Accelerator Optimization
Ong, M; DeHope, B; Griffin, K; Goerz, D; Kihara, R; Vogtlin, G; Zentler, J M; Scarpetti, R
2003-01-01
Lawrence Livermore National Laboratory has designed and constructed a test stand to improve the voltage regulation in our Flash X-Ray (FXR) accelerator cell. The goal is to create a more mono-energetic electron beam that will create an x-ray source with a smaller spot size. Studying the interaction of the beam and pulse-power system with the accelerator cell will improve the design of high-current accelerators at Livermore and elsewhere. On the test stand, a standard FXR cell is driven by a flexible pulse-power system and the beam current is simulated with a switched center conductor. The test stand is fully instrumented with high-speed digitizers to document the effect of impedance mismatches when the cell is operated under various full-voltage conditions. A time-domain reflectometry technique was also developed to characterize the beam and cell interactions by measuring the impedance of the accelerator and pulse-power component. Computer models are being developed in parallel with the testing program to validate the measurements and evaluate different design changes. Both 3D transient electromagnetic and circuit models are being used
The interpretation of Charpy impact test data using hyper-logistic fitting functions
Helm, J.L.
1996-01-01
The hyperbolic tangent function is used almost exclusively for computer assisted curve fitting of Charpy impact test data. Unfortunately, there is no physical basis to justify the use of this function and it cannot be generalized to test data that exhibits asymmetry. Using simple physical arguments, a semi-empirical model is derived and identified as a special case of the so called hyper-logistic equation. Although one solution of this equation is the hyperbolic tangent, other more physically interpretable solutions are provided. From the mathematics of the family of functions derived from the hyper-logistic equation, several useful generalizations are made such that asymmetric and wavy Charpy data can be physically interpreted
Predicting Student Success on the Texas Chemistry STAAR Test: A Logistic Regression Analysis
Johnson, William L.; Johnson, Annabel M.; Johnson, Jared
2012-01-01
Background: The context is the new Texas STAAR end-of-course testing program. Purpose: The authors developed a logistic regression model to predict who would pass-or-fail the new Texas chemistry STAAR end-of-course exam. Setting: Robert E. Lee High School (5A) with an enrollment of 2700 students, Tyler, Texas. Date of the study was the 2011-2012…
Testing Parametric versus Semiparametric Modelling in Generalized Linear Models
Härdle, W.K.; Mammen, E.; Müller, M.D.
1996-01-01
We consider a generalized partially linear model E(Y|X,T) = G{X'b + m(T)} where G is a known function, b is an unknown parameter vector, and m is an unknown function.The paper introduces a test statistic which allows to decide between a parametric and a semiparametric model: (i) m is linear, i.e.
lmerTest Package: Tests in Linear Mixed Effects Models
Kuznetsova, Alexandra; Brockhoff, Per B.; Christensen, Rune Haubo Bojesen
2017-01-01
One of the frequent questions by users of the mixed model function lmer of the lme4 package has been: How can I get p values for the F and t tests for objects returned by lmer? The lmerTest package extends the 'lmerMod' class of the lme4 package, by overloading the anova and summary functions...... by providing p values for tests for fixed effects. We have implemented the Satterthwaite's method for approximating degrees of freedom for the t and F tests. We have also implemented the construction of Type I - III ANOVA tables. Furthermore, one may also obtain the summary as well as the anova table using...
Dai, James Y.; Chan, Kwun Chuen Gary; Hsu, Li
2014-01-01
Instrumental variable regression is one way to overcome unmeasured confounding and estimate causal effect in observational studies. Built on structural mean models, there has been considerale work recently developed for consistent estimation of causal relative risk and causal odds ratio. Such models can sometimes suffer from identification issues for weak instruments. This hampered the applicability of Mendelian randomization analysis in genetic epidemiology. When there are multiple genetic variants available as instrumental variables, and causal effect is defined in a generalized linear model in the presence of unmeasured confounders, we propose to test concordance between instrumental variable effects on the intermediate exposure and instrumental variable effects on the disease outcome, as a means to test the causal effect. We show that a class of generalized least squares estimators provide valid and consistent tests of causality. For causal effect of a continuous exposure on a dichotomous outcome in logistic models, the proposed estimators are shown to be asymptotically conservative. When the disease outcome is rare, such estimators are consistent due to the log-linear approximation of the logistic function. Optimality of such estimators relative to the well-known two-stage least squares estimator and the double-logistic structural mean model is further discussed. PMID:24863158
Testing hypotheses for differences between linear regression lines
Stanley J. Zarnoch
2009-01-01
Five hypotheses are identified for testing differences between simple linear regression lines. The distinctions between these hypotheses are based on a priori assumptions and illustrated with full and reduced models. The contrast approach is presented as an easy and complete method for testing for overall differences between the regressions and for making pairwise...
A Comparison of the One-and Three-Parameter Logistic Models on Measures of Test Efficiency.
Benson, Jeri
Two methods of item selection were used to select sets of 40 items from a 50-item verbal analogies test, and the resulting item sets were compared for relative efficiency. The BICAL program was used to select the 40 items having the best mean square fit to the one parameter logistic (Rasch) model. The LOGIST program was used to select the 40 items…
Wang, Hsiao-Fan; Hsu, Hsin-Wei
2010-11-01
With the urgency of global warming, green supply chain management, logistics in particular, has drawn the attention of researchers. Although there are closed-loop green logistics models in the literature, most of them do not consider the uncertain environment in general terms. In this study, a generalized model is proposed where the uncertainty is expressed by fuzzy numbers. An interval programming model is proposed by the defined means and mean square imprecision index obtained from the integrated information of all the level cuts of fuzzy numbers. The resolution for interval programming is based on the decision maker (DM)'s preference. The resulting solution provides useful information on the expected solutions under a confidence level containing a degree of risk. The results suggest that the more optimistic the DM is, the better is the resulting solution. However, a higher risk of violation of the resource constraints is also present. By defining this probable risk, a solution procedure was developed with numerical illustrations. This provides a DM trade-off mechanism between logistic cost and the risk. Copyright 2010 Elsevier Ltd. All rights reserved.
An alternative test for verifying electronic balance linearity
Thomas, I.R.
1998-02-01
This paper presents an alternative method for verifying electronic balance linearity and accuracy. This method is being developed for safeguards weighings (weighings for the control and accountability of nuclear material) at the Idaho National Engineering and Environmental Laboratory (INEEL). With regard to balance linearity and accuracy, DOE Order 5633.3B, Control and Accountability of Nuclear Materials, Paragraph 2, 4, e, (1), (a) Scales and Balances Program, states: ''All scales and balances used for accountability purposes shall be maintained in good working condition, recalibrated according to an established schedule, and checked for accuracy and linearity on each day that the scale or balance is used for accountability purposes.'' Various tests have been proposed for testing accuracy and linearity. In the 1991 Measurement Science Conference, Dr. Walter E. Kupper presented a paper entitled: ''Validation of High Accuracy Weighing Equipment.'' Dr. Kupper emphasized that tolerance checks for calibrated, state-of-the-art electronic equipment need not be complicated, and he presented four easy steps for verifying that a calibrated balance is operating correctly. These tests evaluate the standard deviation of successive weighings (of the same load), the off-center error, the calibration error, and the error due to nonlinearity. This method of balance validation is undoubtedly an authoritative means of ensuring balance operability, yet it could have two drawbacks: one, the test for linearity is not intuitively obvious, especially from a statistical viewpoint; and two, there is an absence of definitively defined testing limits. Hence, this paper describes an alternative means of verifying electronic balance linearity and accuracy that is being developed for safeguards measurements at the INEEL
NLC. A test accelerator for the next linear collider
Ruth, R.D.; Adolphsen, C.; Bane, K.; Boyce, R.F.; Burke, D.L.; Callin, R.; Caryotakis, G.; Cassel, R.; Clark, S.L.; Deruyter, H.; Fant, K.; Fuller, R.; Heifets, S.; Hoag, H.; Humphrey, R.; Kheifets, S.; Koontz, R.; Kroll, N.M.; Lavine, T.; Loew, G.A.; Menegat, A.; Miller, R.H.; Nantista, C.; Paterson, J.M.; Pearson, C.; Phillips, R.; Rifkin, J.; Spencer, J.; Tantawi, S.; Thompson, K.A.; Vlieks, A.; Vylet, V.; Wang, J.W.; Wilson, P.B.; Yeremian, A.; Youngman, B.
1993-01-01
At SLAC, we are pursuing the design of a Next Linear Collider (NLC) which would begin with a center-of-mass energy of 0.5 TeV, and be upgradable to at least 1.0 TeV. To achieve this high energy, we have been working on the development of a high-gradient 11.4-GHz (X-band) linear accelerator for the main linac of the collider. In this paper, we present the design of a 'Next Linear Collider Test Accelerator' (NLCTA). The goal of the NLCTA is to incorporate the new technologies of X-band accelerator structures, RF pulse compression systems and klystrons into a short linac which will then be a test bed for beam dynamics issues related to high-gradient acceleration. (orig.)
A test accelerator for the next linear collider
Ruth, R.D.; Adolphsen, C.; Bane, K.; Boyce, R.F.; Burke, D.L.; Callin, R.; Caryotakis, G.; Cassel, R.; Clark, S.L.; Deruyter, H.; Fant, K.; Fuller, R.; Heifets, S.; Hoag, H.; Humphrey, R.; Kheifets, S.; Koontz, R.; Lavine, T.; Loew, G.A.; Menegat, A.; Miller, R.H.; Paterson, J.M.; Pearson, C.; Phillips, R.; Rifkin, J.; Spencer, J.; Tantawi, S.; Thompson, K.A.; Vlieks, A.; Vylet, V.; Wang, J.W.; Wilson, P.B.; Yeremian, A.; Youngman, B.; Kroll, N.M.; Nantista, C.
1993-07-01
At SLAC, the authors are pursuing the design of a Next Linear Collider (NLC) which would begin with a center-of-mass energy of 0.5 TeV, and be upgradable to at least 1.0 TeV. To achieve this high energy, they have been working on the development of a high-gradient 11.4-GHz (X-band) linear accelerator for the main linac of the collider. In this paper, they present the design of a open-quotes Next Linear Collider Test Acceleratorclose quotes (NLCTA). The goal of the NLCTA is to incorporate the new technologies of X-band accelerator structures, RF pulse compression systems and klystrons into a short linac which will then be a test bed for beam dynamics issues related to high-gradient acceleration
Eke, Gemma; Holttum, Sue; Hayward, Mark
2012-03-01
Previous research highlights barriers to clinical psychologists conducting research, but has rarely examined U.K. clinical psychologists. The study investigated U.K. clinical psychologists' self-reported research output and tested part of a theoretical model of factors influencing their intention to conduct research. Questionnaires were mailed to 1,300 U.K. clinical psychologists. Three hundred and seventy-four questionnaires were returned (29% response-rate). This study replicated in a U.K. sample the finding that the modal number of publications was zero, highlighted in a number of U.K. and U.S. studies. Research intention was bimodally distributed, and logistic regression classified 78% of cases successfully. Outcome expectations, perceived behavioral control and normative beliefs mediated between research training environment and intention. Further research should explore how research is negotiated in clinical roles, and this issue should be incorporated into prequalification training. © 2012 Wiley Periodicals, Inc.
Jiménez-Huete, Adolfo; Riva, Elena; Toledano, Rafael; Campo, Pablo; Esteban, Jesús; Barrio, Antonio Del; Franch, Oriol
2014-12-01
The validity of neuropsychological tests for the differential diagnosis of degenerative dementias may depend on the clinical context. We constructed a series of logistic models taking into account this factor. We retrospectively analyzed the demographic and neuropsychological data of 301 patients with probable Alzheimer's disease (AD), frontotemporal degeneration (FTLD), or dementia with Lewy bodies (DLB). Nine models were constructed taking into account the diagnostic question (eg, AD vs DLB) and subpopulation (incident vs prevalent). The AD versus DLB model for all patients, including memory recovery and phonological fluency, was highly accurate (area under the curve = 0.919, sensitivity = 90%, and specificity = 80%). The results were comparable in incident and prevalent cases. The FTLD versus AD and DLB versus FTLD models were both inaccurate. The models constructed from basic neuropsychological variables allowed an accurate differential diagnosis of AD versus DLB but not of FTLD versus AD or DLB. © The Author(s) 2014.
Analysis of the Latin Square Task with Linear Logistic Test Models
Zeuch, Nina; Holling, Heinz; Kuhn, Jorg-Tobias
2011-01-01
The Latin Square Task (LST) was developed by Birney, Halford, and Andrews [Birney, D. P., Halford, G. S., & Andrews, G. (2006). Measuring the influence of cognitive complexity on relational reasoning: The development of the Latin Square Task. Educational and Psychological Measurement, 66, 146-171.] and represents a non-domain specific,…
Evaluation of the linear power of HANARO test fuel bundles
Lee, Choong Sung; Seo, C. G.; Lee, B. C.; Kim, H. R
2001-02-01
The HANARO fuel was developed by AECL and it is configured in a bundle of rods containing uranium silicide. AECL has conducted a variety of tests using specimen in order to achieve its qualification and licensing and the highest linear power was evaluated to be 112.8kW/m. In design stage of HANARO, the best estimated maximum linear power at hot spot was found to occur in the transition core from the initial to the equilibrium and its value was 108kW/m, which exceeds 112.8kW/m if the physics uncertainty of the HANARO nuclear design model is taken into account. Consequently, the licensing body issued the conditional permit to operate HANARO and the fuel integrity at the linear power higher than 112.8kW/m was requested to be confirmed through irradiation tests by realizing its repeatability. Hereby, KAERI designed uninstrumented and instrumented test fuel bundles and conducted their burnup tests. In parallel with the tests, the nuclear design model has been revised and updated to enable us to pursue the pin-by-pin power history. This report describes the best estimated power history of the test fuel bundles using the revised model. In conclusion, HANARO fuel keeps its integrity at power condition greater than 120kW/m.
Claudio Roberto Fóffano Vasconcelos
2016-01-01
Full Text Available The aim of this study is to examine empirically the validity of PPP in the context of unit root tests based on linear and non-linear models of the real effective exchange rate of Argentina, Brazil, Chile, Colombia, Mexico, Peru and Venezuela. For this purpose, we apply the Harvey et al. (2008 linearity test and the non-linear unit root test (Kruse, 2011. The results show that the series with linear characteristics are Argentina, Brazil, Chile, Colombia and Peru and those with non-linear characteristics are Mexico and Venezuela. The linear unit root tests indicate that the real effective exchange rate is stationary for Chile and Peru, and the non-linear unit root tests evidence that Mexico is stationary. In the period analyzed, the results show support for the validity of PPP in only three of the seven countries.
Miguel-Hurtado, Oscar; Guest, Richard; Stevenage, Sarah V; Neil, Greg J; Black, Sue
2016-01-01
Understanding the relationship between physiological measurements from human subjects and their demographic data is important within both the biometric and forensic domains. In this paper we explore the relationship between measurements of the human hand and a range of demographic features. We assess the ability of linear regression and machine learning classifiers to predict demographics from hand features, thereby providing evidence on both the strength of relationship and the key features underpinning this relationship. Our results show that we are able to predict sex, height, weight and foot size accurately within various data-range bin sizes, with machine learning classification algorithms out-performing linear regression in most situations. In addition, we identify the features used to provide these relationships applicable across multiple applications.
Thurstonian models for sensory discrimination tests as generalized linear models
Brockhoff, Per B.; Christensen, Rune Haubo Bojesen
2010-01-01
as a so-called generalized linear model. The underlying sensory difference 6 becomes directly a parameter of the statistical model and the estimate d' and it's standard error becomes the "usual" output of the statistical analysis. The d' for the monadic A-NOT A method is shown to appear as a standard......Sensory discrimination tests such as the triangle, duo-trio, 2-AFC and 3-AFC tests produce binary data and the Thurstonian decision rule links the underlying sensory difference 6 to the observed number of correct responses. In this paper it is shown how each of these four situations can be viewed...
Adaptive linear rank tests for eQTL studies.
Szymczak, Silke; Scheinhardt, Markus O; Zeller, Tanja; Wild, Philipp S; Blankenberg, Stefan; Ziegler, Andreas
2013-02-10
Expression quantitative trait loci (eQTL) studies are performed to identify single-nucleotide polymorphisms that modify average expression values of genes, proteins, or metabolites, depending on the genotype. As expression values are often not normally distributed, statistical methods for eQTL studies should be valid and powerful in these situations. Adaptive tests are promising alternatives to standard approaches, such as the analysis of variance or the Kruskal-Wallis test. In a two-stage procedure, skewness and tail length of the distributions are estimated and used to select one of several linear rank tests. In this study, we compare two adaptive tests that were proposed in the literature using extensive Monte Carlo simulations of a wide range of different symmetric and skewed distributions. We derive a new adaptive test that combines the advantages of both literature-based approaches. The new test does not require the user to specify a distribution. It is slightly less powerful than the locally most powerful rank test for the correct distribution and at least as powerful as the maximin efficiency robust rank test. We illustrate the application of all tests using two examples from different eQTL studies. Copyright © 2012 John Wiley & Sons, Ltd.
Paccaud Fred
2004-04-01
Full Text Available Abstract Background We sought to improve upon previously published statistical modeling strategies for binary classification of dyslipidemia for general population screening purposes based on the waist-to-hip circumference ratio and body mass index anthropometric measurements. Methods Study subjects were participants in WHO-MONICA population-based surveys conducted in two Swiss regions. Outcome variables were based on the total serum cholesterol to high density lipoprotein cholesterol ratio. The other potential predictor variables were gender, age, current cigarette smoking, and hypertension. The models investigated were: (i linear regression; (ii logistic classification; (iii regression trees; (iv classification trees (iii and iv are collectively known as "CART". Binary classification performance of the region-specific models was externally validated by classifying the subjects from the other region. Results Waist-to-hip circumference ratio and body mass index remained modest predictors of dyslipidemia. Correct classification rates for all models were 60–80%, with marked gender differences. Gender-specific models provided only small gains in classification. The external validations provided assurance about the stability of the models. Conclusions There were no striking differences between either the algebraic (i, ii vs. non-algebraic (iii, iv, or the regression (i, iii vs. classification (ii, iv modeling approaches. Anticipated advantages of the CART vs. simple additive linear and logistic models were less than expected in this particular application with a relatively small set of predictor variables. CART models may be more useful when considering main effects and interactions between larger sets of predictor variables.
Testing for one Generalized Linear Single Order Parameter
Ellegaard, Niels Langager; Christensen, Tage Emil; Dyre, Jeppe
We examine a linear single order parameter model for thermoviscoelastic relaxation in viscous liquids, allowing for a distribution of relaxation times. In this model the relaxation of volume and entalpy is completely described by the relaxation of one internal order parameter. In contrast to prior...... work the order parameter may be chosen to have a non-exponential relaxation. The model predictions contradict the general consensus of the properties of viscous liquids in two ways: (i) The model predicts that following a linear isobaric temperature step, the normalized volume and entalpy relaxation...... responses or extrapolate from measurements of a glassy state away from equilibrium. Starting from a master equation description of inherent dynamics, we calculate the complex thermodynamic response functions. We device a way of testing for the generalized single order parameter model by measuring 3 complex...
Santana Isabel
2011-08-01
Full Text Available Abstract Background Dementia and cognitive impairment associated with aging are a major medical and social concern. Neuropsychological testing is a key element in the diagnostic procedures of Mild Cognitive Impairment (MCI, but has presently a limited value in the prediction of progression to dementia. We advance the hypothesis that newer statistical classification methods derived from data mining and machine learning methods like Neural Networks, Support Vector Machines and Random Forests can improve accuracy, sensitivity and specificity of predictions obtained from neuropsychological testing. Seven non parametric classifiers derived from data mining methods (Multilayer Perceptrons Neural Networks, Radial Basis Function Neural Networks, Support Vector Machines, CART, CHAID and QUEST Classification Trees and Random Forests were compared to three traditional classifiers (Linear Discriminant Analysis, Quadratic Discriminant Analysis and Logistic Regression in terms of overall classification accuracy, specificity, sensitivity, Area under the ROC curve and Press'Q. Model predictors were 10 neuropsychological tests currently used in the diagnosis of dementia. Statistical distributions of classification parameters obtained from a 5-fold cross-validation were compared using the Friedman's nonparametric test. Results Press' Q test showed that all classifiers performed better than chance alone (p Conclusions When taking into account sensitivity, specificity and overall classification accuracy Random Forests and Linear Discriminant analysis rank first among all the classifiers tested in prediction of dementia using several neuropsychological tests. These methods may be used to improve accuracy, sensitivity and specificity of Dementia predictions from neuropsychological testing.
High gradient tests of SLAC Linear Collider Accelerator Structures
Wang, J.W.; Deruyter, H.; Eichner, J.; Fant, K.H.; Hoag, H.A.; Koontz, R.F.; Lavine, T.; Loew, G.A.; Loewen, R.; Menegat, L.
1994-08-01
This paper describes the current SLAC R ampersand D program to develop room temperature accelerator structures for the Next Linear Collider (NLC). The structures are designed to operate at 11.4 GHz at an accelerating gradient in the range of 50 to 100 MV/m. In the past year a 26 cm constant-impedance traveling-wave section, a 75 cm constant-impedance traveling-wave section, and a 1.8 m traveling-wave section with detuned deflecting modes have been high-power tested. The paper presents a brief description of the RF test setup, the design and manufacturing details of the structures, and a discussion of test results including field emission, RF processing, dark current spectrum and RF breakdown
Testing Linear Temporal Logic Formulae on Finite Execution Traces
Havelund, Klaus; Rosu, Grigore; Norvig, Peter (Technical Monitor)
2001-01-01
We present an algorithm for efficiently testing Linear Temporal Logic (LTL) formulae on finite execution traces. The standard models of LTL are infinite traces, reflecting the behavior of reactive and concurrent systems which conceptually may be continuously alive. In most past applications of LTL. theorem provers and model checkers have been used to formally prove that down-scaled models satisfy such LTL specifications. Our goal is instead to use LTL for up-scaled testing of real software applications. Such tests correspond to analyzing the conformance of finite traces against LTL formulae. We first describe what it means for a finite trace to satisfy an LTL property. We then suggest an optimized algorithm based on transforming LTL formulae. The work is done using the Maude rewriting system. which turns out to provide a perfect notation and an efficient rewriting engine for performing these experiments.
Poullis, Michael
2014-11-01
EuroSCORE II, despite improving on the original EuroSCORE system, has not solved all the calibration and predictability issues. Recursive, non-linear and mixed recursive and non-linear regression analysis were assessed with regard to sensitivity, specificity and predictability of the original EuroSCORE and EuroSCORE II systems. The original logistic EuroSCORE, EuroSCORE II and recursive, non-linear and mixed recursive and non-linear regression analyses of these risk models were assessed via receiver operator characteristic curves (ROC) and Hosmer-Lemeshow statistic analysis with regard to the accuracy of predicting in-hospital mortality. Analysis was performed for isolated coronary artery bypass grafts (CABGs) (n = 2913), aortic valve replacement (AVR) (n = 814), mitral valve surgery (n = 340), combined AVR and CABG (n = 517), aortic (n = 350), miscellaneous cases (n = 642), and combinations of the above cases (n = 5576). The original EuroSCORE had an ROC below 0.7 for isolated AVR and combined AVR and CABG. None of the methods described increased the ROC above 0.7. The EuroSCORE II risk model had an ROC below 0.7 for isolated AVR only. Recursive regression, non-linear regression, and mixed recursive and non-linear regression all increased the ROC above 0.7 for isolated AVR. The original EuroSCORE had a Hosmer-Lemeshow statistic that was above 0.05 for all patients and the subgroups analysed. All of the techniques markedly increased the Hosmer-Lemeshow statistic. The EuroSCORE II risk model had a Hosmer-Lemeshow statistic that was significant for all patients (P linear regression failed to improve on the original Hosmer-Lemeshow statistic. The mixed recursive and non-linear regression using the EuroSCORE II risk model was the only model that produced an ROC of 0.7 or above for all patients and procedures and had a Hosmer-Lemeshow statistic that was highly non-significant. The original EuroSCORE and the EuroSCORE II risk models do not have adequate ROC and Hosmer
One testing method of dynamic linearity of an accelerometer
Lei Jing-Yu
2015-01-01
Full Text Available To effectively test dynamic linearity of an accelerometer over a wide rang of 104 g to about 20 × 104g, one published patent technology is first experimentally verified and analysed, and its deficient is presented, then based on stress wave propagation theory on the thin long bar, the relation between the strain signal and the corresponding acceleration signal is obtained, one special link of two coaxial projectile is developed. These two coaxial metal cylinders (inner cylinder and circular tube are used as projectiles, to prevent their mutual slip inside the gun barrel during movement, the one end of two projectiles is always fastened by small screws. Ti6-AL4-V bar with diameter of 30 mm is used to propagate loading stress pulse. The resultant compression wave can be measured by the strain gauges on the bar, and a half –sine strain pulse is obtained. The measuring accelerometer is attached on the other end of the bar by a vacuum clamp. In this clamp, the accelerometer only bear compression wave, the reflected tension pulse make the accelerometer off the bar. Using this system, dynamic linearity measurement of accelerometer can be easily tested in wider range of acceleration values. And a really measuring results are presented.
A test to evaluation non-linear soil structure interaction
Hagiwara, T.; Kitada, Y.
2005-01-01
JNES is planning a new project to study non-linear soil-structure interaction (SSI) effect under large earthquake ground motions equivalent to and/or over a design earthquake ground motion of S2. Concerning the SSI test, it is pointed out that handling of the scale effect of the specimen taking into account the surrounding soil on the earthquake response evaluation to the actual structure is essential issue for the scaled model test. Thus, for the test, the largest specimen possible and the biggest input motion possible are necessary. Taking into account the above issues, new test methodology, which utilizes artificial earthquake ground motion, is considered desirable if it can be performed at a realistic cost. With this motivation, we have studied the test methodology which applying blasting power as for a big earthquake ground motion. The information from a coalmine company in the U.S.A. indicates that the works performed in the surface coalmine to blast a rock covering a coal layer generates a big artificial ground motion, which is similar to earthquake ground motion. Application of this artificial earthquake ground motion for the SSI test is considered very promising because the blasting work is carried out periodically for mining coal so that we can apply artificial motions generated by the work if we construct a building model at a closed point to the blasting work area. The major purposes of the test are to understand (a) basic earthquake response characteristics of a Nuclear Power Plant (NPP) reactor building when a large earthquake strikes the NPP site and (b) nonlinear characteristics of SSI phenomenon during a big earthquake. In the paper of ICONE-13, we will introduce the test method and basic characteristics of measured artificial ground motions generated by the blasting works on an actual site. (authors)
Eekhout, I.; Wiel, M.A. van de; Heymans, M.W.
2017-01-01
Background. Multiple imputation is a recommended method to handle missing data. For significance testing after multiple imputation, Rubin’s Rules (RR) are easily applied to pool parameter estimates. In a logistic regression model, to consider whether a categorical covariate with more than two levels
Fidalgo, Angel M.; Alavi, Seyed Mohammad; Amirian, Seyed Mohammad Reza
2014-01-01
This study examines three controversial aspects in differential item functioning (DIF) detection by logistic regression (LR) models: first, the relative effectiveness of different analytical strategies for detecting DIF; second, the suitability of the Wald statistic for determining the statistical significance of the parameters of interest; and…
Rudner, Lawrence
2016-01-01
In the machine learning literature, it is commonly accepted as fact that as calibration sample sizes increase, Naïve Bayes classifiers initially outperform Logistic Regression classifiers in terms of classification accuracy. Applied to subtests from an on-line final examination and from a highly regarded certification examination, this study shows…
Next Linear Collider Test Accelerator conceptual design report
1993-08-01
This document presents the scientific justification and the conceptual design for the open-quotes Next Linear Collider Test Acceleratorclose quotes (NLCTA) at SLAC. The goals of the NLCTA are to integrate the new technologies of X-band accelerator structures and rf systems being developed for the Next Linear Collider, to measure the growth of the open-quotes dark currentclose quotes generated by rf field emission in the accelerator, to demonstrate multi-bunch beam-loading energy compensation and suppression of higher-order deflecting modes, and to measure any transverse components of the accelerating field. The NLCTA will be a 42-meter-long beam line consisting, consecutively, of a thermionic-cathode gun, an X-band buncher, a magnetic chicane, six 1.8-meter-long sections of 11.4-GHz accelerator structure, and a magnetic spectrometer. Initially, the unloaded accelerating gradient will be 50 MV/m. A higher-gradient upgrade option eventually would increase the unloaded gradient to 100 MV/m
Linear and logistic regression analysis
Tripepi, G.; Jager, K. J.; Dekker, F. W.; Zoccali, C.
2008-01-01
In previous articles of this series, we focused on relative risks and odds ratios as measures of effect to assess the relationship between exposure to risk factors and clinical outcomes and on control for confounding. In randomized clinical trials, the random allocation of patients is hoped to
Linear shrinkage test: justification for its reintroduction as a standard South African test method
Sampson, LR
2009-06-04
Full Text Available Several problems with the linear shrinkage test specified in Method A4 of the THM 1 1979 were addressed as part of this investigation in an effort to improve the alleged poor reproducibility of the test and justify its reintroduction into THM 1. A...
Gudehus, Timm
2012-01-01
Modern logistics comprises operative logistics, analytical logistics and management of logistic networks. Central task of operative logistics is the efficient supply of required goods at the right place within the right time. Tasks of analytical logistics are designing optimal networks and systems, developing strategies for planning, scheduling and operation, and organizing efficient order and performance processes. Logistic management plans, implements and operates logistic networks and schedules orders, stocks and resources. This reference-book offers a unique survey of modern logistics. It contains proven strategies, rules and tools for the solution of a multitude of logistic problems. The analytically derived algorithms and formulas can be used for the computer-based planning of logistic systems and for the dynamic scheduling of orders and resources in supply networks. They enable significant improvements of performance, quality and costs. Their application is demonstrated by several examples from industr...
Cold Regions Logistic Supportability Testing of Electronic, Avionic and Communications Equipment.
1985-06-20
Comment : 2. Have all data collected been reviewed for correctness and completeness? YES NO . Comment : 3. Were the facilities, test equipment...insufficient test planning? YES NO . Comment : 5. Were the test results compromised in any way due to test performance procedures? YES NO . Comment : 6. Were the...test results compromised in any way due to test control pro- cedures? YES NO Comment : 7. Were the test results compromised in any way due to data
Cold Regions Logistic Supportability Testing of Wheeled, Tracked and Special Purpose Vehicles
1985-06-24
NO . Comment : 2. Have all data collected been reviewed for correctness and completeness? YES NO . Comment : 3. Were the facilities, test equipment...insufficient test planning? YES NO . Comment : 5. Were the test results compromised in any way due to test performance procedures? YES NO . Comment : 6...Were the test results compromised in any way due to test control pro- cedures? YES NO Comment : 7. Were the test results compromised in any way due to
Cold Regions Logistic Supportability Testing of Construction, Support and Service Equipment.
1985-06-25
1985 APPENDIX B - POST-TEST CHECKLIST 1. Have test data been collected, recorded, and presented in accordance . with this TOP? YES NO . Comment : 2...planning? YES NO . Comment : 5. Were the test results compromised in any way due to test performance procedures? YES NO . Comment : 6. Were the test results...compromised in any way due to test control pro- - cedures? YES NO Comment : 7. Were the test results compromised in any way due to data collection
Parameter estimation and hypothesis testing in linear models
Koch, Karl-Rudolf
1999-01-01
The necessity to publish the second edition of this book arose when its third German edition had just been published. This second English edition is there fore a translation of the third German edition of Parameter Estimation and Hypothesis Testing in Linear Models, published in 1997. It differs from the first English edition by the addition of a new chapter on robust estimation of parameters and the deletion of the section on discriminant analysis, which has been more completely dealt with by the author in the book Bayesian In ference with Geodetic Applications, Springer-Verlag, Berlin Heidelberg New York, 1990. Smaller additions and deletions have been incorporated, to im prove the text, to point out new developments or to eliminate errors which became apparent. A few examples have been also added. I thank Springer-Verlag for publishing this second edition and for the assistance in checking the translation, although the responsibility of errors remains with the author. I also want to express my thanks...
Panibratetc, Anastasiia
2015-01-01
This research is a review of warehouse logistics on the example of Kannustalo Oy, located in Kannus, Western region of Finland. Kannustalo is an international company of designing, manufacturing and assembling block and turn-key houses. The research subject is logistics process in warehouse system of industrial company. In my work I discussed about theoretical aspect of logistics, logistic functions and processes. Later I considered warehouse as a part of logistics system and provided inf...
Kulikova, Olga
2016-01-01
This thesis was focused on the analysis of the concept of reverse logistics and actual reverse processes which are implemented in mining industry and finding solutions for the optimization of reverse logistics in this sphere. The objective of this paper was the assessment of the development of reverse logistics in mining industry on the example of potash production. The theoretical part was based on reverse logistics and mining waste related literature and provided foundations for further...
Kellermeyer, Steven Bruce
2011-01-01
In the last few decades high-stakes testing has become more political than educational. The Districts within Arizona are bound by the mandates of both AZ LEARNS and the No Child Left Behind Act of 2001. At the time of this writing, both legislative mandates relied on the Arizona Instrument for Measuring Standards (AIMS) as State Tests for gauging…
A general equation to obtain multiple cut-off scores on a test from multinomial logistic regression.
Bersabé, Rosa; Rivas, Teresa
2010-05-01
The authors derive a general equation to compute multiple cut-offs on a total test score in order to classify individuals into more than two ordinal categories. The equation is derived from the multinomial logistic regression (MLR) model, which is an extension of the binary logistic regression (BLR) model to accommodate polytomous outcome variables. From this analytical procedure, cut-off scores are established at the test score (the predictor variable) at which an individual is as likely to be in category j as in category j+1 of an ordinal outcome variable. The application of the complete procedure is illustrated by an example with data from an actual study on eating disorders. In this example, two cut-off scores on the Eating Attitudes Test (EAT-26) scores are obtained in order to classify individuals into three ordinal categories: asymptomatic, symptomatic and eating disorder. Diagnoses were made from the responses to a self-report (Q-EDD) that operationalises DSM-IV criteria for eating disorders. Alternatives to the MLR model to set multiple cut-off scores are discussed.
Celovsky, A.; Lesco, R.; Gale, B.; Sypes, J.
2003-01-01
Ten years ago Atomic Energy of Canada developed a Type B(U)-85 shipping container for the global transport of highly radioactive materials. This paper reviews the development of the container, including a summary of the design requirements, a review of the selected materials and key design elements, and the results of the major qualification tests (drop testing, fire test, leak tightness testing, and shielding integrity tests). As a result of the testing, improvements to the structural, thermal and containment design were made. Such improvements, and reasons thereof, are noted. Also provided is a summary of the additional analysis work required to upgrade the package from a Type B(U) to a Type B(F), i.e. essentially upgrading the container to include fissile radioisotopes to the authorized radioactive contents list. Having a certified shipping container is only one aspect governing the global shipments of radioactive material. By necessity the shipment of radioactive material is a highly regulated environment. This paper also explores the experiences with other key aspects of radioactive shipments, including the service procedures used to maintain the container certification, the associated compliance program for radioactive material shipments, and the shipping logistics involved in the transport. (author)
Woensel, van T.
2012-01-01
This lecture focuses on Smart Logistics referring to these intelligent managerial decisions related to the design, operations and control of the transportation chain processes in an efficient and cost-effective way. The starting point for Smart Logistics is the key observation that the real-life
Linearity and Misspecification Tests for Vector Smooth Transition Regression Models
Teräsvirta, Timo; Yang, Yukai
The purpose of the paper is to derive Lagrange multiplier and Lagrange multiplier type specification and misspecification tests for vector smooth transition regression models. We report results from simulation studies in which the size and power properties of the proposed asymptotic tests in small...
Standard Test Method for Measuring Dose for Use in Linear Accelerator Pulsed Radiation Effects Tests
American Society for Testing and Materials. Philadelphia
2011-01-01
1.1 This test method covers a calorimetric measurement of the total dose delivered in a single pulse of electrons from an electron linear accelerator or a flash X-ray machine (FXR, e-beam mode) used as an ionizing source in radiation-effects testing. The test method is designed for use with pulses of electrons in the energy range from 10 to 50 MeV and is only valid for cases in which both the calorimeter and the test specimen to be irradiated are“thin” compared to the range of these electrons in the materials of which they are constructed. 1.2 The procedure described can be used in those cases in which (1) the dose delivered in a single pulse is 5 Gy (matl) (500 rd (matl)) or greater, or (2) multiple pulses of a lower dose can be delivered in a short time compared to the thermal time constant of the calorimeter. Matl refers to the material of the calorimeter. The minimum dose per pulse that can be acceptably monitored depends on the variables of the particular test, including pulse rate, pulse uniformity...
Testing for marginal linear effects in quantile regression
Wang, Huixia Judy
2017-10-23
The paper develops a new marginal testing procedure to detect significant predictors that are associated with the conditional quantiles of a scalar response. The idea is to fit the marginal quantile regression on each predictor one at a time, and then to base the test on the t-statistics that are associated with the most predictive predictors. A resampling method is devised to calibrate this test statistic, which has non-regular limiting behaviour due to the selection of the most predictive variables. Asymptotic validity of the procedure is established in a general quantile regression setting in which the marginal quantile regression models can be misspecified. Even though a fixed dimension is assumed to derive the asymptotic results, the test proposed is applicable and computationally feasible for large dimensional predictors. The method is more flexible than existing marginal screening test methods based on mean regression and has the added advantage of being robust against outliers in the response. The approach is illustrated by using an application to a human immunodeficiency virus drug resistance data set.
Testing for marginal linear effects in quantile regression
Wang, Huixia Judy; McKeague, Ian W.; Qian, Min
2017-01-01
The paper develops a new marginal testing procedure to detect significant predictors that are associated with the conditional quantiles of a scalar response. The idea is to fit the marginal quantile regression on each predictor one at a time, and then to base the test on the t-statistics that are associated with the most predictive predictors. A resampling method is devised to calibrate this test statistic, which has non-regular limiting behaviour due to the selection of the most predictive variables. Asymptotic validity of the procedure is established in a general quantile regression setting in which the marginal quantile regression models can be misspecified. Even though a fixed dimension is assumed to derive the asymptotic results, the test proposed is applicable and computationally feasible for large dimensional predictors. The method is more flexible than existing marginal screening test methods based on mean regression and has the added advantage of being robust against outliers in the response. The approach is illustrated by using an application to a human immunodeficiency virus drug resistance data set.
Understanding logistic regression analysis
Sperandei, Sandro
2014-01-01
Logistic regression is used to obtain odds ratio in the presence of more than one explanatory variable. The procedure is quite similar to multiple linear regression, with the exception that the response variable is binomial. The result is the impact of each variable on the odds ratio of the observed event of interest. The main advantage is to avoid confounding effects by analyzing the association of all variables together. In this article, we explain the logistic regression procedure using ex...
Pacino, Dario; Voss, Stefan; Jensen, Rune Møller
2013-01-01
This book constitutes the refereed proceedings of the 4th International Conference on Computational Logistics, ICCL 2013, held in Copenhagen, Denmark, in September 2013. The 19 papers presented in this volume were carefully reviewed and selected for inclusion in the book. They are organized in to...... in topical sections named: maritime shipping, road transport, vehicle routing problems, aviation applications, and logistics and supply chain management.......This book constitutes the refereed proceedings of the 4th International Conference on Computational Logistics, ICCL 2013, held in Copenhagen, Denmark, in September 2013. The 19 papers presented in this volume were carefully reviewed and selected for inclusion in the book. They are organized...
This book constitutes the refereed proceedings of the 4th International Conference on Computational Logistics, ICCL 2013, held in Copenhagen, Denmark, in September 2013. The 19 papers presented in this volume were carefully reviewed and selected for inclusion in the book. They are organized in to...... in topical sections named: maritime shipping, road transport, vehicle routing problems, aviation applications, and logistics and supply chain management.......This book constitutes the refereed proceedings of the 4th International Conference on Computational Logistics, ICCL 2013, held in Copenhagen, Denmark, in September 2013. The 19 papers presented in this volume were carefully reviewed and selected for inclusion in the book. They are organized...
Ned Rossiter
2014-03-01
Full Text Available As the managerial art and science of coordinating the movement of people, finance and things, logistical operations are central to contemporary capital. Despite its materiality in the form of communications and transport infrastructure, logistics remains an abstract machine for many. This is largely due to the compartmental structure of global supply chains and the invisibility of code. In registering the mediating force of logistics, the essay considers parametric politics as an architecture of intervention for both game design and software development. There are implications here not only for gameplay, but also the invention of method and governance of labour. How, for instance, might game design facilitate the production of a political knowledge of logistics? This becomes a matter to address for labour power vis-à-vis collective research on infrastructure, software and global supply chains.
Linear Accelerator Test Facility at LNF Conceptual Design Report
Valente, Paolo; Bolli, Bruno; Buonomo, Bruno; Cantarella, Sergio; Ceccarelli, Riccardo; Cecchinelli, Alberto; Cerafogli, Oreste; Clementi, Renato; Di Giulio, Claudio; Esposito, Adolfo; Frasciello, Oscar; Foggetta, Luca; Ghigo, Andrea; Incremona, Simona; Iungo, Franco; Mascio, Roberto; Martelli, Stefano; Piermarini, Graziano; Sabbatini, Lucia; Sardone, Franco; Sensolini, Giancarlo; Ricci, Ruggero; Rossi, Luis Antonio; Rotundo, Ugo; Stella, Angelo; Strabioli, Serena; Zarlenga, Raffaele
2016-01-01
Test beam and irradiation facilities are the key enabling infrastructures for research in high energy physics (HEP) and astro-particles. In the last 11 years the Beam-Test Facility (BTF) of the DA{\\Phi}NE accelerator complex in the Frascati laboratory has gained an important role in the European infrastructures devoted to the development and testing of particle detectors. At the same time the BTF operation has been largely shadowed, in terms of resources, by the running of the DA{\\Phi}NE electron-positron collider. The present proposal is aimed at improving the present performance of the facility from two different points of view: extending the range of application for the LINAC beam extracted to the BTF lines, in particular in the (in some sense opposite) directions of hosting fundamental physics and providing electron irradiation also for industrial users; extending the life of the LINAC beyond or independently from its use as injector of the DA{\\Phi}NE collider, as it is also a key element of the electron/...
Structural Dynamic Analyses And Test Predictions For Spacecraft Structures With Non-Linearities
Vergniaud, Jean-Baptiste; Soula, Laurent; Newerla, Alfred
2012-07-01
The overall objective of the mechanical development and verification process is to ensure that the spacecraft structure is able to sustain the mechanical environments encountered during launch. In general the spacecraft structures are a-priori assumed to behave linear, i.e. the responses to a static load or dynamic excitation, respectively, will increase or decrease proportionally to the amplitude of the load or excitation induced. However, past experiences have shown that various non-linearities might exist in spacecraft structures and the consequences of their dynamic effects can significantly affect the development and verification process. Current processes are mainly adapted to linear spacecraft structure behaviour. No clear rules exist for dealing with major structure non-linearities. They are handled outside the process by individual analysis and margin policy, and analyses after tests to justify the CLA coverage. Non-linearities can primarily affect the current spacecraft development and verification process on two aspects. Prediction of flights loads by launcher/satellite coupled loads analyses (CLA): only linear satellite models are delivered for performing CLA and no well-established rules exist how to properly linearize a model when non- linearities are present. The potential impact of the linearization on the results of the CLA has not yet been properly analyzed. There are thus difficulties to assess that CLA results will cover actual flight levels. Management of satellite verification tests: the CLA results generated with a linear satellite FEM are assumed flight representative. If the internal non- linearities are present in the tested satellite then there might be difficulties to determine which input level must be passed to cover satellite internal loads. The non-linear behaviour can also disturb the shaker control, putting the satellite at risk by potentially imposing too high levels. This paper presents the results of a test campaign performed in
Kocjan, Boštjan; Poljak, Mario; Oštrbenk, Anja
2015-01-01
Introduction: HPV-52 is one of the most frequent human papillomavirus (HPV) genotypes causing significant cervical pathology. The most widely used HPV genotyping assay, the Roche Linear Array HPV Genotyping Test (Linear Array), is unable to identify HPV- 52 status in samples containing HPV-33, HPV-35, and/or HPV-58. Methods: Linear Array HPV-52 analytical specificity was established by testing 100 specimens reactive with the Linear Array HPV- 33/35/52/58 cross-reactive probe, but not with the...
Quantum tests for the linearity and permutation invariance of Boolean functions
Hillery, Mark [Department of Physics, Hunter College of the City University of New York, 695 Park Avenue, New York, New York 10021 (United States); Andersson, Erika [SUPA, School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)
2011-12-15
The goal in function property testing is to determine whether a black-box Boolean function has a certain property or is {epsilon}-far from having that property. The performance of the algorithm is judged by how many calls need to be made to the black box in order to determine, with high probability, which of the two alternatives is the case. Here we present two quantum algorithms, the first to determine whether the function is linear and the second to determine whether it is symmetric (invariant under permutations of the arguments). Both require order {epsilon}{sup -2/3} calls to the oracle, which is better than known classical algorithms. In addition, in the case of linearity testing, if the function is linear, the quantum algorithm identifies which linear function it is. The linearity test combines the Bernstein-Vazirani algorithm and amplitude amplification, while the test to determine whether a function is symmetric uses projective measurements and amplitude amplification.
Patt, P. J.
1985-01-01
The design of a coaxial linear magnetic spring which incorporates a linear motor to control axial motion and overcome system damping is presented, and the results of static and dynamic tests are reported. The system has nominal stiffness 25,000 N/m and is designed to oscillate a 900-g component over a 4.6-mm stroke in a Stirling-cycle cryogenic refrigerator being developed for long-service (5-10-yr) space applications (Stolfi et al., 1983). Mosaics of 10 radially magnetized high-coercivity SmCO5 segments enclosed in Ti cans are employed, and the device is found to have quality factor 70-100, corresponding to energy-storage efficiency 91-94 percent. Drawings, diagrams, and graphs are provided.
Hidalgo, María D; López-Martínez, María D; Gómez-Benito, Juana; Guilera, Georgina
2016-01-01
Short scales are typically used in the social, behavioural and health sciences. This is relevant since test length can influence whether items showing DIF are correctly flagged. This paper compares the relative effectiveness of discriminant logistic regression (DLR) and IRTLRDIF for detecting DIF in polytomous short tests. A simulation study was designed. Test length, sample size, DIF amount and item response categories number were manipulated. Type I error and power were evaluated. IRTLRDIF and DLR yielded Type I error rates close to nominal level in no-DIF conditions. Under DIF conditions, Type I error rates were affected by test length DIF amount, degree of test contamination, sample size and number of item response categories. DLR showed a higher Type I error rate than did IRTLRDIF. Power rates were affected by DIF amount and sample size, but not by test length. DLR achieved higher power rates than did IRTLRDIF in very short tests, although the high Type I error rate involved means that this result cannot be taken into account. Test length had an important impact on the Type I error rate. IRTLRDIF and DLR showed a low power rate in short tests and with small sample sizes.
Design and performance testing of an ultrasonic linear motor with dual piezoelectric actuators.
Smithmaitrie, Pruittikorn; Suybangdum, Panumas; Laoratanakul, Pitak; Muensit, Nantakan
2012-05-01
In this work, design and performance testing of an ultrasonic linear motor with dual piezoelectric actuator patches are studied. The motor system consists of a linear stator, a pre-load weight, and two piezoelectric actuator patches. The piezoelectric actuators are bonded with the linear elastic stator at specific locations. The stator generates propagating waves when the piezoelectric actuators are subjected to harmonic excitations. Vibration characteristics of the linear stator are analyzed and compared with finite element and experimental results. The analytical, finite element, and experimental results show agreement. In the experiments, performance of the ultrasonic linear motor is tested. Relationships between velocity and pre-load weight, velocity and applied voltage, driving force and applied voltage, and velocity and driving force are reported. The design of the dual piezoelectric actuators yields a simpler structure with a smaller number of actuators and lower stator stiffness compared with a conventional design of an ultrasonic linear motor with fully laminated piezoelectric actuators.
Analysis of separation test for automatic brake adjuster based on linear radon transformation
Luo, Zai; Jiang, Wensong; Guo, Bin; Fan, Weijun; Lu, Yi
2015-01-01
The linear Radon transformation is applied to extract inflection points for online test system under the noise conditions. The linear Radon transformation has a strong ability of anti-noise and anti-interference by fitting the online test curve in several parts, which makes it easy to handle consecutive inflection points. We applied the linear Radon transformation to the separation test system to solve the separating clearance of automatic brake adjuster. The experimental results show that the feature point extraction error of the gradient maximum optimal method is approximately equal to ±0.100, while the feature point extraction error of linear Radon transformation method can reach to ±0.010, which has a lower error than the former one. In addition, the linear Radon transformation is robust.
An experimental test of the linear no-threshold theory of radiation carcinogenesis
Cohen, B.L.
1990-01-01
There is a substantial body of quantitative information on radiation-induced cancer at high dose, but there are no data at low dose. The usual method for estimating effects of low-level radiation is to assume a linear no-threshold dependence. if this linear no-threshold assumption were not used, essentially all fears about radiation would disappear. Since these fears are costing tens of billions of dollars, it is most important that the linear no-threshold theory be tested at low dose. An opportunity for possibly testing the linear no-threshold concept is now available at low dose due to radon in homes. The purpose of this paper is to attempt to use this data to test the linear no-threshold theory
Radiation testing of thick-wall objects using a linear accelerator or Co-60
Depending on the energy required, a 60 Co source or various types of betatrons and linear accelerators may be used for radiation testing of thick-walled metal parts. While 60 Co sources are easily transported, accelerators are not, but a transportable linear accelerator is described
Huitzing, Hiddo A.
2004-01-01
This article shows how set covering with item sampling (SCIS) methods can be used in the analysis and preanalysis of linear programming models for test assembly (LPTA). LPTA models can construct tests, fulfilling a set of constraints set by the test assembler. Sometimes, no solution to the LPTA model exists. The model is then said to be…
Power properties of invariant tests for spatial autocorrelation in linear regression
Martellosio, F.
2006-01-01
Many popular tests for residual spatial autocorrelation in the context of the linear regression model belong to the class of invariant tests. This paper derives a number of exact properties of the power function of such tests. In particular, we extend the work of Krämer (2005, Journal of Statistical
Lee, C. S.; Seo, C. K.; Lee, B. C.; Kim, H. N.; Kang, B. W. [KAERI, Taejon (Korea, Republic of)
2000-10-01
The HANARO fuel, U{sub 3}Si-Al, has been developed by AECL and tested in NRU reactor. Due to the lack of the data performed under the high power, the repetitive conduct of the irradiation test was required under the power greater than 108kW/m, which is the estimated maximum linear power in the design stage. Accordingly, the instrumented test bundle with SPND(Self Powered Neutron Detector) was fabricated and its irradiation test was performed in IR2 of HANARO. The measured thermal neutron flux with SPND is compared with calculation results by HANAFMS(HANARO Fuel Management System). The difference in the measured and calculated thermal flux values are below {+-}11% and the accuracy of the linear power predicted by HANAFMS is consequently accompanied. Therefore, it is believed that the maximum linear power above 120kW/m is achieved during the irradiation test of the test bundle.
Virtual instrumention-based linearity test platform for DCCT of digital power supply at SSRF
Tang Junlong; Li Deming; Shen Tianjian; Liu Hong
2008-01-01
Based on virtual instrumentation, a reliable and effective test platform, performing instrument control, data acquisition and data recording, has been established to evaluate linearity of high performance DCCT (DC current transducer) for digital power supply at Shanghai Synchrotron Radiation Facility (SSRF). The software in LabVIEW language was developed to perform computer communication via serial communication (RS232) and GPIB, providing a friendly user interface to the linearity test platform. This makes it easy to test the linearity and control power on or off and current output of high-precision and high-current DC constant current output power supply. The experimental data, stored in an EXCEL file, can be processed to obtain DCCT linearity, and provide basis to further analyze DCCT performance in the future. (authors)
Assessment of the Roche Linear Array HPV Genotyping Test within the VALGENT framework.
Xu, Lan; Oštrbenk, Anja; Poljak, Mario; Arbyn, Marc
2018-01-01
Cervical cancer screening programs are switching from cytology-based screening to high-risk (hr) HPV testing. Only clinically validated tests should be used in clinical practice. To assess the clinical performance of the Roche Linear Array HPV genotyping test (Linear Array) within the VALGENT-3 framework. The VALGENT framework is designed for comprehensive comparison and clinical validation of HPV tests that have limited to extended genotyping capacity. The Linear Array enables type-specific detection of 37 HPV types. For the purpose of this study, Linear Array results were designated as positive only if one of the 13 hrHPV types also included in the Hybrid Capture 2 (HC2) was detected. The VALGENT-3 framework comprised 1600 samples obtained from Slovenian women (1300 sequential cases from routine cervical cancer screening enriched with 300 cytological abnormal samples). Sensitivity for cervical intraepithelial neoplasia of grade 2 or worse (CIN2+) (n=127) and specificity for Linear Array and for HC2 and non-inferiority of Linear Array relative to HC2 was checked. In addition, the prevalence of separate hrHPV types in the screening population, as well as the concordance for presence of HPV16, HPV18 and other hrHPV types between Linear Array and the Abbott RealTime High Risk HPV test (RealTime) were assessed. The clinical sensitivity and specificity for CIN2+ of the Linear Array in the total study population was 97.6% (95% CI, 93.3-99.5%) and 91.7% (95% CI, 90.0-93.2%), respectively. The relative sensitivity and specificity of Linear Array vs HC2 was 1.02 [95% CI, 0.98-1.05, (pLinear Array in the screening population was 10.5% (95% CI, 8.9-12.3%) with HPV16 and HPV18 detected in 2.3% and 0.9% of the samples, respectively. Excellent agreement for presence or absence of HPV16, HPV18 and other hrHPV between Linear Array and RealTime was observed. Linear Array showed similar sensitivity with higher specificity to detect CIN2+ compared to HC2. Detection of 13 hrHPV types
Understanding logistic regression analysis.
Sperandei, Sandro
2014-01-01
Logistic regression is used to obtain odds ratio in the presence of more than one explanatory variable. The procedure is quite similar to multiple linear regression, with the exception that the response variable is binomial. The result is the impact of each variable on the odds ratio of the observed event of interest. The main advantage is to avoid confounding effects by analyzing the association of all variables together. In this article, we explain the logistic regression procedure using examples to make it as simple as possible. After definition of the technique, the basic interpretation of the results is highlighted and then some special issues are discussed.
Performance Testing of a High Temperature Linear Alternator for Stirling Convertors
Metscher, Jonathan F.; Geng, Steven M.
2016-01-01
The NASA Glenn Research Center has conducted performance testing of a high temperature linear alternator (HTLA) in support of Stirling power convertor development for potential future Radioisotope Power Systems (RPS). The high temperature linear alternator is a modified version of that used in Sunpower's Advanced Stirling Convertor (ASC), and is capable of operation at temperatures up to 200 deg. Increasing the temperature capability of the linear alternator could expand the mission set of future Stirling RPS designs. High temperature Neodymium-Iron-Boron (Nd-Fe-B) magnets were selected for the HTLA application, and were fully characterized and tested prior to use. Higher temperature epoxy for alternator assembly was also selected and tested for thermal stability and strength. A characterization test was performed on the HTLA to measure its performance at various amplitudes, loads, and temperatures. HTLA endurance testing at 200 deg is currently underway.
An Interactive Method to Solve Infeasibility in Linear Programming Test Assembling Models
Huitzing, Hiddo A.
2004-01-01
In optimal assembly of tests from item banks, linear programming (LP) models have proved to be very useful. Assembly by hand has become nearly impossible, but these LP techniques are able to find the best solutions, given the demands and needs of the test to be assembled and the specifics of the item bank from which it is assembled. However,…
Rakkapao, Suttida; Prasitpong, Singha; Arayathanitkul, Kwan
2016-01-01
This study investigated the multiple-choice test of understanding of vectors (TUV), by applying item response theory (IRT). The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming…
Scott W. Keith
2014-09-01
Full Text Available This paper details the design, evaluation, and implementation of a framework for detecting and modeling nonlinearity between a binary outcome and a continuous predictor variable adjusted for covariates in complex samples. The framework provides familiar-looking parameterizations of output in terms of linear slope coefficients and odds ratios. Estimation methods focus on maximum likelihood optimization of piecewise linear free-knot splines formulated as B-splines. Correctly specifying the optimal number and positions of the knots improves the model, but is marked by computational intensity and numerical instability. Our inference methods utilize both parametric and nonparametric bootstrapping. Unlike other nonlinear modeling packages, this framework is designed to incorporate multistage survey sample designs common to nationally representative datasets. We illustrate the approach and evaluate its performance in specifying the correct number of knots under various conditions with an example using body mass index (BMI; kg/m2 and the complex multi-stage sampling design from the Third National Health and Nutrition Examination Survey to simulate binary mortality outcomes data having realistic nonlinear sample-weighted risk associations with BMI. BMI and mortality data provide a particularly apt example and area of application since BMI is commonly recorded in large health surveys with complex designs, often categorized for modeling, and nonlinearly related to mortality. When complex sample design considerations were ignored, our method was generally similar to or more accurate than two common model selection procedures, Schwarz’s Bayesian Information Criterion (BIC and Akaike’s Information Criterion (AIC, in terms of correctly selecting the correct number of knots. Our approach provided accurate knot selections when complex sampling weights were incorporated, while AIC and BIC were not effective under these conditions.
American Society for Testing and Materials. Philadelphia
2005-01-01
1.1 This test method determines the degree of linearity of a photovoltaic device parameter with respect to a test parameter, for example, short-circuit current with respect to irradiance. 1.2 The linearity determined by this test method applies only at the time of testing, and implies no past or future performance level. 1.3 This test method applies only to non-concentrator terrestrial photovoltaic devices. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Measuring efficiency in logistics
Milan Milovan Andrejić
2013-06-01
Full Text Available Dynamic market and environmental changes greatly affect operating of logistics systems. Logistics systems have to realize their activities and processes in an efficient way. The main objective of this paper is to analyze different aspects of efficiency measurement in logistics and to propose appropriate models of measurement. Measuring efficiency in logistics is a complex process that requires consideration of all subsystems, processes and activities as well as the impact of various financial, operational, environmental, quality and other factors. The proposed models have a basis in the Data Envelopment Analysis method. They could help managers in decision making and corrective actions processes. The tests and results of the model show the importance of input and output variables selection.
Testing the existence of optical linear polarization in young brown dwarfs
Manjavacas, E.; Miles-Páez, P. A.; Zapatero-Osorio, M. R.; Goldman, B.; Buenzli, E.; Henning, T.; Pallé, E.; Fang, M.
2017-07-01
Linear polarization can be used as a probe of the existence of atmospheric condensates in ultracool dwarfs. Models predict that the observed linear polarization increases with the degree of oblateness, which is inversely proportional to the surface gravity. We aimed to test the existence of optical linear polarization in a sample of bright young brown dwarfs, with spectral types between M6 and L2, observable from the Calar Alto Observatory, and cataloged previously as low gravity objects using spectroscopy. Linear polarimetric images were collected in I and R band using CAFOS at the 2.2-m telescope in Calar Alto Observatory (Spain). The flux ratio method was employed to determine the linear polarization degrees. With a confidence of 3σ, our data indicate that all targets have a linear polarimetry degree in average below 0.69 per cent in the I band, and below 1.0 per cent in the R band, at the time they were observed. We detected significant (I.e. P/σ ≥ 3) linear polarization for the young M6 dwarf 2MASS J04221413+1530525 in the R band, with a degree of p* = 0.81 ± 0.17 per cent.
Targeting: Logistic Regression, Special Cases and Extensions
Helmut Schaeben
2014-12-01
Full Text Available Logistic regression is a classical linear model for logit-transformed conditional probabilities of a binary target variable. It recovers the true conditional probabilities if the joint distribution of predictors and the target is of log-linear form. Weights-of-evidence is an ordinary logistic regression with parameters equal to the differences of the weights of evidence if all predictor variables are discrete and conditionally independent given the target variable. The hypothesis of conditional independence can be tested in terms of log-linear models. If the assumption of conditional independence is violated, the application of weights-of-evidence does not only corrupt the predicted conditional probabilities, but also their rank transform. Logistic regression models, including the interaction terms, can account for the lack of conditional independence, appropriate interaction terms compensate exactly for violations of conditional independence. Multilayer artificial neural nets may be seen as nested regression-like models, with some sigmoidal activation function. Most often, the logistic function is used as the activation function. If the net topology, i.e., its control, is sufficiently versatile to mimic interaction terms, artificial neural nets are able to account for violations of conditional independence and yield very similar results. Weights-of-evidence cannot reasonably include interaction terms; subsequent modifications of the weights, as often suggested, cannot emulate the effect of interaction terms.
Gillespie, S.
2000-01-01
This report describes the tests performed to validate the CRWMS ''Analysis and Logistics Visually Interactive'' Model (CALVIN) Version 3.0 (V3.0) computer code (STN: 10074-3.0-00). To validate the code, a series of test cases was developed in the CALVIN V3.0 Validation Test Plan (CRWMS M and O 1999a) that exercises the principal calculation models and options of CALVIN V3.0. Twenty-five test cases were developed: 18 logistics test cases and 7 cost test cases. These cases test the features of CALVIN in a sequential manner, so that the validation of each test case is used to demonstrate the accuracy of the input to subsequent calculations. Where necessary, the test cases utilize reduced-size data tables to make the hand calculations used to verify the results more tractable, while still adequately testing the code's capabilities. Acceptance criteria, were established for the logistics and cost test cases in the Validation Test Plan (CRWMS M and O 1999a). The Logistics test cases were developed to test the following CALVIN calculation models: Spent nuclear fuel (SNF) and reactivity calculations; Options for altering reactor life; Adjustment of commercial SNF (CSNF) acceptance rates for fiscal year calculations and mid-year acceptance start; Fuel selection, transportation cask loading, and shipping to the Monitored Geologic Repository (MGR); Transportation cask shipping to and storage at an Interim Storage Facility (ISF); Reactor pool allocation options; and Disposal options at the MGR. Two types of cost test cases were developed: cases to validate the detailed transportation costs, and cases to validate the costs associated with the Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) and Regional Servicing Contractors (RSCs). For each test case, values calculated using Microsoft Excel 97 worksheets were compared to CALVIN V3.0 scenarios with the same input data and assumptions. All of the test case results compare with
Design of Linear Control System for Wind Turbine Blade Fatigue Testing
Toft, Anders; Roe-Poulsen, Bjarke Nørskov; Christiansen, Rasmus
2016-01-01
This paper proposes a linear method for wind turbine blade fatigue testing at Siemens Wind Power. The setup consists of a blade, an actuator (motor and load mass) that acts on the blade with a sinusoidal moment, and a distribution of strain gauges to measure the blade flexure. Based...... difficult to control. To make a linear controller, a different approach has been chosen, namely making a controller which is not regulating on the input frequency, but on the input amplitude. A non-linear mechanical model for the blade and the motor has been constructed. This model has been simplified based...... on the desired output, namely the amplitude of the blade. Furthermore, the model has been linearised to make it suitable for linear analysis and control design methods.\\\\ The controller is designed based on a simplified and linearised model, and its gain parameter determined using pole placement. The model...
Berdaky, Mafalda Feliciano
2000-01-01
This work presents the operational part of the final process of the establishment of a radiotherapy service with a linear accelerator (6 MeV photon beams), including the acceptance tests, commissioning tests and the implementation of a quality control program through routine mechanical and radiation tests. All acceptance tests were satisfactory, showing results below the allowed limits of the manufacturer, the commissioning tests presented results within those of the international recommendations. The quality control program was performed during 34 months and showed an excellent stability of this accelerator. (author)
Efficient Market Hypothesis in South Africa: Evidence from Linear and Nonlinear Unit Root Tests
Andrew Phiri
2015-12-01
Full Text Available This study investigates the weak form efficient market hypothesis (EMH for five generalized stock indices in the Johannesburg Stock Exchange (JSE using weekly data collected from 31st January 2000 to 16th December 2014. In particular, we test for weak form market efficiency using a battery of linear and nonlinear unit root testing procedures comprising of the classical augmented Dickey-Fuller (ADF tests, the two-regime threshold autoregressive (TAR unit root tests described in Enders and Granger (1998 as well as the three-regime unit root tests described in Bec, Salem, and Carrasco (2004. Based on our empirical analysis, we are able to demonstrate that whilst the linear unit root tests advocate for unit roots within the time series, the nonlinear unit root tests suggest that most stock indices are threshold stationary processes. These results bridge two opposing contentions obtained from previous studies by concluding that under a linear framework the JSE stock indices offer support in favour of weak form market efficiency whereas when nonlinearity is accounted for, a majority of the indices violate the weak form EMH.
Significance tests for the wavelet cross spectrum and wavelet linear coherence
Z. Ge
2008-12-01
Full Text Available This work attempts to develop significance tests for the wavelet cross spectrum and the wavelet linear coherence as a follow-up study on Ge (2007. Conventional approaches that are used by Torrence and Compo (1998 based on stationary background noise time series were used here in estimating the sampling distributions of the wavelet cross spectrum and the wavelet linear coherence. The sampling distributions are then used for establishing significance levels for these two wavelet-based quantities. In addition to these two wavelet quantities, properties of the phase angle of the wavelet cross spectrum of, or the phase difference between, two Gaussian white noise series are discussed. It is found that the tangent of the principal part of the phase angle approximately has a standard Cauchy distribution and the phase angle is uniformly distributed, which makes it impossible to establish significance levels for the phase angle. The simulated signals clearly show that, when there is no linear relation between the two analysed signals, the phase angle disperses into the entire range of [−π,π] with fairly high probabilities for values close to ±π to occur. Conversely, when linear relations are present, the phase angle of the wavelet cross spectrum settles around an associated value with considerably reduced fluctuations. When two signals are linearly coupled, their wavelet linear coherence will attain values close to one. The significance test of the wavelet linear coherence can therefore be used to complement the inspection of the phase angle of the wavelet cross spectrum. The developed significance tests are also applied to actual data sets, simultaneously recorded wind speed and wave elevation series measured from a NOAA buoy on Lake Michigan. Significance levels of the wavelet cross spectrum and the wavelet linear coherence between the winds and the waves reasonably separated meaningful peaks from those generated by randomness in the data set. As
Kushwaha, Pratishtha; Jaiswal, Deeksha; Dheera, A.; Upreti, Udita; Chaudhari, Suresh; Kinhikar, Rajesh; Deshpande, Deepak; Shrivastava, Shyam
2016-01-01
Daily quality assurance (QA) for high precision radiotherapy equipments is very important to maintain the mechanical and dosimetric accuracy for patient treatments. Gross deviations in these parameters may have an adverse impact on the delivery of the treatments to patients. We report the results of daily QA tests performed over a period of three months for two Varian linear accelerators and a Tomotherapy machine
Testing linear growth rate formulas of non-scale endogenous growth models
Ziesemer, Thomas
2017-01-01
Endogenous growth theory has produced formulas for steady-state growth rates of income per capita which are linear in the growth rate of the population. Depending on the details of the models, slopes and intercepts are positive, zero or negative. Empirical tests have taken over the assumption of
Application of range-test in multiple linear regression analysis in ...
Application of range-test in multiple linear regression analysis in the presence of outliers is studied in this paper. First, the plot of the explanatory variables (i.e. Administration, Social/Commercial, Economic services and Transfer) on the dependent variable (i.e. GDP) was done to identify the statistical trend over the years.
Christensen, Bent Jesper; Kruse, Robinson; Sibbertsen, Philipp
We consider hypothesis testing in a general linear time series regression framework when the possibly fractional order of integration of the error term is unknown. We show that the approach suggested by Vogelsang (1998a) for the case of integer integration does not apply to the case of fractional...
Space and frequency-multiplexed optical linear algebra processor - Fabrication and initial tests
Casasent, D.; Jackson, J.
1986-01-01
A new optical linear algebra processor architecture is described. Space and frequency-multiplexing are used to accommodate bipolar and complex-valued data. A fabricated laboratory version of this processor is described, the electronic support system used is discussed, and initial test data obtained on it are presented.
Proceedings of the 2. International Linear Collider Test-beam workshop - LCTW'09
Wormser, G.; Poeschl, R.; Takeshi, M.; Yu, J.; Hauptman, J.; Jeans, D.; Velthuis, J.; Repond, J.; Stanitzki, M.; Chefdeville, M.; Pauletta, G.; Hauptman, J.; Kulis, S.; Charpy, A.; Rivera, R.; Turchetti, M.; Vos, M.; Dehmelt, K.; Settles, R.; Decotigny, D.; Killenberg, M.; Haas, D.; Gaede, F.; Graf, N.; Wing, M.; Gaede, F.; Karstensen, S.; Meyners, N.; Hast, C.; Vrba, V.; Takeshita, T.; Kawagoe, K.; Linssen, L.; Ramberg, E.; Demarteau, M.; Fisk, H.E.; Savoy-Navarro, A.; Videau, H.; Boudry, V.; Hauptman, J.; Lipton, R.; Nelson, T.
2009-01-01
At this workshop detector and simulation experts have described and discussed the necessary ILC (International Linear Collider) detector research and development program in view of its need for test beams. This workshop has provided an opportunity to evaluate the capabilities and shortcomings of existing facilities in the context of planned test beam activities. This document gathers together the slides of the presentations. The presentations have been classified into 4 topics: -) plans of sub-detectors - calorimetry, silicon and gaseous tracking, -) data acquisition, -) test beam facilities, and -) resources and infrastructure for future test beams
Non-Linear Numerical Modeling and Experimental Testing of a Point Absorber Wave Energy Converter
Zurkinden, Andrew Stephen; Ferri, Francesco; Beatty, S.
2014-01-01
the calculation of the non-linear hydrostatic restoring moment by a cubic polynomial function fit to laboratory test results. Moreover, moments due to viscous drag are evaluated on the oscillating hemisphere considering the horizontal and vertical drag force components. The influence on the motions of this non.......e. H/λ≤0.02. For steep waves, H/λ≥0.04 however, the relative velocities between the body and the waves increase thus requiring inclusion of the non-linear hydrostatic restoring moment to effectively predict the dynamics of the wave energy converter. For operation of the device with a passively damping...
Recovery coefficients as a test of system linearity of response in PET
Geworski, L.; Munz, D.L.; Knoop, B.; Hofmann, M.; Knapp, W.H.
2002-01-01
Aim: New imaging protocols have created an increasing demand for quantitation in dedicated PET. Besides attenuation and scatter correction the recovery correction, accounting for the instrument's limited spatial resolution, has gained importance. For clinical practicability these corrections should work independent from the object, i.e. from the actual distribution of emitter and absorber. Aim of the study was to test this object independency, i.e. system linearity of response, by comparing recovery coefficients (RC) determined for different object geometries. In fact, this comparison may serve as a final test on system linearity of response, as measured on the quantitative accuracy by which the activity concentration in small lesions can be recovered. Method: For hot and cold spot imaging situations spatial distribution of activity is different. Therefore, scatter correction algorithm has to deal with different scatter distributions. If all factors disturbing system linearity, specifically scatter and attenuation, are corrected to a sufficient degree of accuracy, the system behaves linearly resulting in the theoretical relationship. CSRC = (1-HSRC). Thus, this equation, applied hot and cold spot measurements, will serve as a test on the effectiveness of the corrections and, hence, as a test of system linearity of response. Following IEC standard procedures (IEC 61675-1) measurements were done with and without interplane septa (2D/3D) on an ECAT EXACT 922 using a cylindrical phantom containing six spheres of different diameters (10 mm - 40 mm). All data were corrected for attenuation (transmission scan) and scatter (2D: deconvolution, 3D: scatter model), as implemented in the scanner's standard software. Recovery coefficients were determined for cold (CSRC) and hot (HSRC) lesions using both 2D and 3D acquisition mode. Results: CSRC directly measured versus CSRC calculated according to eq. (1) from HSRC resulted in an excellent agreement for both 2D and 3D data
Varadharajan, Ekambaram; Ramasubramanian, Velayudham
2013-01-01
Aim The RapidArc commissioning and Acceptance Testing program will test and ensure accuracy in DMLC position, precise dose-rate control during gantry rotation and accurate control of gantry speed. Background Recently, we have upgraded our linear accelerator capable of performing IMRT which was functional from 2007 with image guided RapidArc facility. The installation of VMAT in the existing linear accelerator is a tedious process which requires many quality assurance procedures before the proper commissioning of the facility and these procedures are discussed in this study. Materials and methods Output of the machine at different dose rates was measured to verify its consistency at different dose rates. Monitor and chamber linearity at different dose rates were checked. DMLC QA comprising of MLC transmission factor measurement and dosimetric leaf gap measurements were performed using 0.13 cm3 and 0.65 cm3 Farmer type ionization chamber, dose 1 dosimeter, and IAEA 30 cm × 30 cm × 30 cm water phantom. Picket fence test, garden fence test, tests to check leaf positioning accuracy due to carriage movement, calibration of the leaves, leaf speed stability effects due to the acceleration and deceleration of leaves, accuracy and calibration of leaves in producing complex fields, effects of interleaf friction, etc. were verified using EDR2 therapy films, Vidar scanner, Omnipro accept software, amorphous silicon based electronic portal imaging device and EPIQA software.1–8 Results All the DMLC related quality assurance tests were performed and evaluated by film dosimetry, portal dosimetry and EPIQA.7 Conclusion Results confirmed that the linear accelerator is capable of performing accurate VMAT. PMID:24416566
Varadharajan, Ekambaram; Ramasubramanian, Velayudham
2013-01-01
The RapidArc commissioning and Acceptance Testing program will test and ensure accuracy in DMLC position, precise dose-rate control during gantry rotation and accurate control of gantry speed. Recently, we have upgraded our linear accelerator capable of performing IMRT which was functional from 2007 with image guided RapidArc facility. The installation of VMAT in the existing linear accelerator is a tedious process which requires many quality assurance procedures before the proper commissioning of the facility and these procedures are discussed in this study. Output of the machine at different dose rates was measured to verify its consistency at different dose rates. Monitor and chamber linearity at different dose rates were checked. DMLC QA comprising of MLC transmission factor measurement and dosimetric leaf gap measurements were performed using 0.13 cm(3) and 0.65 cm(3) Farmer type ionization chamber, dose 1 dosimeter, and IAEA 30 cm × 30 cm × 30 cm water phantom. Picket fence test, garden fence test, tests to check leaf positioning accuracy due to carriage movement, calibration of the leaves, leaf speed stability effects due to the acceleration and deceleration of leaves, accuracy and calibration of leaves in producing complex fields, effects of interleaf friction, etc. were verified using EDR2 therapy films, Vidar scanner, Omnipro accept software, amorphous silicon based electronic portal imaging device and EPIQA software.(1-8.) All the DMLC related quality assurance tests were performed and evaluated by film dosimetry, portal dosimetry and EPIQA.(7.) Results confirmed that the linear accelerator is capable of performing accurate VMAT.
Tests of the linearity assumption in the dose-effect relationship for radiation-induced cancer
Cohen, A.F.; Cohen, B.L.
1980-01-01
The validity of the BEIR linear extrapolation to low doses of the dose-effect relationship for radiation induced cancer is tested by use of natural radiation making use of selectivity on type of cancer, smoking habits, sex, age group, geographic area and/or time period. For lung cancer, a linear interpolation between zero dose-zero effect and the data from radon-induced cancers in miners implies that the majority of all lung cancers among non-smokers are due to radon; since lung cancers in miners are mostly small-cell undifferentiated (SCU), a rather rare type in general, linearity over predicts the frequency of SCU lung cancers among non smokers by a factor of 10, and among non-smoking females age 25-44 by a factor of 24. Similarly, linearity predicts that the majority of all lung cancers early in this century were due to radon even after due consideration is given to cases missed by poor diagnostic efficiency (this matter is considered in some detail). For the 30-40 age range, linearity over predicts the total lung cancer rate at that time by a factor of 3-6; for SCU lung cancer, the over-prediction is by at least a factor of 10. Other causes of lung cancer are considered which further enhance the degree to which the linearity assumption over-estimates the effects of low level radiation. A similar analysis is applied to leukemia induced by natural radiation. It is concluded that the upper limit for this is not higher than estimates from the linearity hypothesis. (author)
Test results for three prototype models of a linear induction launcher
Zabar, Z.; Lu, X.N.; He, J.L.; Birenbaum, L.; Levi, E.; Kuznetsov, S.B.; Nahemow, M.D.
1991-01-01
This paper reports on the work on the linear induction launcher (LIL) started with an analytical study tht was followed by computer simulations and then was tested by laboratory models. Two mathematical representations have been developed to describe the launcher. The first, based on the field approach with sinusoidal excitation, has been validated by static tests on a small scale prototype fed at constant current and variable frequency. The second, a transient representation using computer simulation allows consideration of energization by means of a capacitor bank and a power conditioner. Tests performed on three small-scale prototypes up to 100 m/s muzzle velocities show good agreement with predicted performance
Estimated of associated uncertainties of the linearity test of dose calibrators
Sousa, Carlos H.S.; Peixoto, Jose G.P.
2013-01-01
Activimeters determine the activity of radioactive samples and them are validated by performance tests. This research determined the expanded uncertainties associated to the linearity test. Were used three dose calibrators and three sources of 99 Tc m for testing using recommended protocol by the IAEA, which considered the decay of radioactive samples. The expanded uncertainties evaluated were not correlated with each other and their analysis considered a rectangular probability distribution. The results are also presented in graphical form by the function of normalized activity measured in terms of conventional true value. (author)
Standard test method for linear-elastic plane-strain fracture toughness KIc of metallic materials
American Society for Testing and Materials. Philadelphia
2009-01-01
1.1 This test method covers the determination of fracture toughness (KIc) of metallic materials under predominantly linear-elastic, plane-strain conditions using fatigue precracked specimens having a thickness of 1.6 mm (0.063 in.) or greater subjected to slowly, or in special (elective) cases rapidly, increasing crack-displacement force. Details of test apparatus, specimen configuration, and experimental procedure are given in the Annexes. Note 1—Plane-strain fracture toughness tests of thinner materials that are sufficiently brittle (see 7.1) can be made using other types of specimens (1). There is no standard test method for such thin materials. 1.2 This test method is divided into two parts. The first part gives general recommendations and requirements for KIc testing. The second part consists of Annexes that give specific information on displacement gage and loading fixture design, special requirements for individual specimen configurations, and detailed procedures for fatigue precracking. Additional a...
Dose calibrator linearity test: {sup 99m}Tc versus {sup 18}F radioisotopes
Willegaignon, Jose; Coura-Filho, George Barberio; Garcez, Alexandre Teles, E-mail: willegaignon@hotmail.com [Instituto do Cancer do Estado de Sao Paulo Octavio Frias de Oliveira (ICESP), Sao Paulo, SP (Brazil); Sapienza, Marcelo Tatit; Buchpiguel, Carlos Alberto [Universidade de Sao Paulo (FM/USP), Sao Paulo, SP (Brazil). Fac. de Medicina; Alves, Carlos Eduardo Gonzalez Ribeiro; Cardona, Marissa Anabel Rivera; Gutterres, Ricardo Fraga [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)
2015-01-15
Objective: the present study was aimed at evaluating the viability of replacing {sup 18}F with {sup 99m}Tc in dose calibrator linearity testing. Materials and methods: the test was performed with sources of {sup 99m}Tc (62 GBq) and {sup 18}F (12 GBq) whose activities were measured up to values lower than 1 MBq. Ratios and deviations between experimental and theoretical {sup 99m}Tc and {sup 18}F sources activities were calculated and subsequently compared. Results: mean deviations between experimental and theoretical {sup 99m}Tc and {sup 18}F sources activities were 0.56 (± 1.79)% and 0.92 (± 1.19)%, respectively. The mean ratio between activities indicated by the device for the {sup 99m}Tc source as measured with the equipment precalibrated to measure {sup 99m}Tc and {sup 18}F was 3.42 (± 0.06), and for the {sup 18}F source this ratio was 3.39 (± 0.05), values considered constant over the measurement time. Conclusion: the results of the linearity test using {sup 99m}Tc were compatible with those obtained with the {sup 18}F source, indicating the viability of utilizing both radioisotopes in dose calibrator linearity testing. Such information in association with the high potential of radiation exposure and costs involved in {sup 18}F acquisition suggest {sup 99m}Tc as the element of choice to perform dose calibrator linearity tests in centers that use {sup 18}F, without any detriment to the procedure as well as to the quality of the nuclear medicine service. (author)
Definition of the linearity loss of the surface temperature in static tensile tests
A. Risitano
2014-10-01
Full Text Available Static tensile tests on material for mechanical constructions have pointed out the linearity loss of the surface temperature with the application of load. This phenomenon is due to the heat generation caused by the local microplasticizations which carry the material to deviate from its completely thermoelastic behavior,. The identification of the static load which determines the loss of linearity of the temperature under stress, becomes extremely important to define a first dynamic characterization of the material. The temperature variations that can be recorded during the static test are often very limited (a few tenths of degree for every 100 MPa in steels and they require the use of special sensors able to measure very low temperature variations. The experience acquired in such analysis highlighted that, dealing with highly accurate sensors or with particular materials, the identification of the first linearity loss (often by eye in the temperature curves, can be influenced by the sensibility of the investigator himself and can lead to incorrect estimates. The aim of this work is to validate the above mentioned observations on different steels, by applying the autocorrelation function to the data collected during the application of a static load. This, in order to make the results of the thermal analysis free from the sensitivity of the operator and to make the results as objective as possible, for defining the closest time of the linearity loss in the temperature-time function.
Hybrid Message-Embedded Cipher Using Logistic Map
Mishra, Mina; Mankar, V. H.
2012-01-01
The proposed hybrid message embedded scheme consists of hill cipher combined with message embedded chaotic scheme. Message-embedded scheme using non-linear feedback shift register as non-linear function and 1-D logistic map as chaotic map is modified, analyzed and tested for avalanche property and strength against known plaintext attack and brute-force attack. Parameter of logistic map acts as a secret key. As we know that the minimum key space to resist brute-force attack is 2100, and it is ...
AAPM Medical Physics Practice Guideline 8.a.: Linear accelerator performance tests.
Smith, Koren; Balter, Peter; Duhon, John; White, Gerald A; Vassy, David L; Miller, Robin A; Serago, Christopher F; Fairobent, Lynne A
2017-07-01
The purpose of this guideline is to provide a list of critical performance tests in order to assist the Qualified Medical Physicist (QMP) in establishing and maintaining a safe and effective quality assurance (QA) program. The performance tests on a linear accelerator (linac) should be selected to fit the clinical patterns of use of the accelerator and care should be given to perform tests which are relevant to detecting errors related to the specific use of the accelerator. A risk assessment was performed on tests from current task group reports on linac QA to highlight those tests that are most effective at maintaining safety and quality for the patient. Recommendations are made on the acquisition of reference or baseline data, the establishment of machine isocenter on a routine basis, basing performance tests on clinical use of the linac, working with vendors to establish QA tests and performing tests after maintenance. The recommended tests proposed in this guideline were chosen based on the results from the risk analysis and the consensus of the guideline's committee. The tests are grouped together by class of test (e.g., dosimetry, mechanical, etc.) and clinical parameter tested. Implementation notes are included for each test so that the QMP can understand the overall goal of each test. This guideline will assist the QMP in developing a comprehensive QA program for linacs in the external beam radiation therapy setting. The committee sought to prioritize tests by their implication on quality and patient safety. The QMP is ultimately responsible for implementing appropriate tests. In the spirit of the report from American Association of Physicists in Medicine Task Group 100, individual institutions are encouraged to analyze the risks involved in their own clinical practice and determine which performance tests are relevant in their own radiotherapy clinics. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on
Tests of the linearity assumption in the dose-effect relationship for radiation-induced cancer
Cohen, A.F.; Cohen, B.L.
1978-01-01
The validity of the BEIR linear extrapolation to low doses of the dose-effect relationship for radiation induced cancer is tested by use of natural radiation making use of selectivity on type of cancer, sex, age group, geographic area, and time period. For lung cancer, a linear interpolation between zero dose-zero effect and the data from radon-induced cancers in miners over-estimates the total number of observed lung cancers in many countries in the early years of this century; the discrepancy is substantially increased if the 30-44 year age range and/or if only females are considered, and by the fact that many other causes of lung cancer are shown to have been important at that time. The degree to which changes of diagnostic efficiency with time can influence the analysis is considered at some length. It is concluded that the linear relationship substantially over-estimates effects of low radiation doses. A similar analysis is applied to leukemia induced by natural radiation, applying selectivity by age, sex, natural background level, and date, and considering other causes. It is concluded that effects substantially larger than those obtained from linear extrapolation are excluded. The use of the selectivities mentioned above is justified by the fact that the incidence of cancer or leukemia is an upper limit on the rate at which it is caused by radiation effects; in determining upper limits it is justifiable to select situations which minimize it. (author)
Solarin, Sakiru Adebola; Lean, Hooi Hooi
2016-01-01
This paper examines the integration properties of the total oil consumption in 57 countries for the period of 1965–2012. A combination of new and powerful linear and nonlinear stationarity tests are employed to achieve the objectives of the study. We find that the oil consumption series in 21 countries follow a nonlinearity path while those in the other countries are linear in nature. Evidence of the presence of a unit root is found for the total oil consumption series in 38 countries while the series is stationary in the remaining 19 countries. An important insight is that the blueprints that were designed to reduce oil consumption are likely to have a permanent effect in most of the countries. - Highlights: • We examine the integration properties of total oil consumption in 57 countries. • We apply new and powerful linear and nonlinear stationarity tests. • Unit root is found in two third of the countries. • Blueprints designed to reduce oil consumption are likely to have permanent effect.
Xu, Zhaoping; Chang, Siqin [School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China)
2010-04-15
A novel four-stroke free-piston engine equipped with a linear electric generator (namely internal combustion linear generator integrated power system) is proposed in this paper to achieve efficient energy conversion from fuel to electricity. Unique features of the novel power system are presented and their effects on the continuous running are discussed, along with potential advantages and disadvantages compared to conventional engines. A single cylinder, gasoline and spark ignition prototype is fabricated with reference to the geometric and control parameters of an existing conventional four-stroke engine. Stable running of the prototype is realized, and a 2.2 kW average output power with the generating efficiency of 32% has been obtained up to now. The feasibility and performance of the proposed design are verified. Detailed testing results from the continuous running prototype are analyzed in this paper for giving insight into the performance and dynamic behaviors of the novel power system. (author)
Speliotopoulos, A.D.; Chiao, Raymond Y.
2004-01-01
The coupling of gravity to matter is explored in the linearized gravity limit. The usual derivation of gravity-matter couplings within the quantum-field-theoretic framework is reviewed. A number of inconsistencies between this derivation of the couplings and the known results of tidal effects on test particles according to classical general relativity are pointed out. As a step towards resolving these inconsistencies, a general laboratory frame fixed on the worldline of an observer is constructed. In this frame, the dynamics of nonrelativistic test particles in the linearized gravity limit is studied, and their Hamiltonian dynamics is derived. It is shown that for stationary metrics this Hamiltonian reduces to the usual Hamiltonian for nonrelativistic particles undergoing geodesic motion. For nonstationary metrics with long-wavelength gravitational waves present (GWs), it reduces to the Hamiltonian for a nonrelativistic particle undergoing geodesic deviation motion. Arbitrary-wavelength GWs couple to the test particle through a vector-potential-like field N a , the net result of the tidal forces that the GW induces in the system, namely, a local velocity field on the system induced by tidal effects, as seen by an observer in the general laboratory frame. Effective electric and magnetic fields, which are related to the electric and magnetic parts of the Weyl tensor, are constructed from N a that obey equations of the same form as Maxwell's equations. A gedankin gravitational Aharonov-Bohm-type experiment using N a to measure the interference of quantum test particles is presented
Rakkapao, Suttida; Prasitpong, Singha; Arayathanitkul, Kwan
2016-12-01
This study investigated the multiple-choice test of understanding of vectors (TUV), by applying item response theory (IRT). The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming unidimensionality and local independence. Moreover, all distractors of the TUV were analyzed from item response curves (IRC) that represent simplified IRT. Data were gathered on 2392 science and engineering freshmen, from three universities in Thailand. The results revealed IRT analysis to be useful in assessing the test since its item parameters are independent of the ability parameters. The IRT framework reveals item-level information, and indicates appropriate ability ranges for the test. Moreover, the IRC analysis can be used to assess the effectiveness of the test's distractors. Both IRT and IRC approaches reveal test characteristics beyond those revealed by the classical analysis methods of tests. Test developers can apply these methods to diagnose and evaluate the features of items at various ability levels of test takers.
A free-piston Stirling engine/linear alternator controls and load interaction test facility
Rauch, Jeffrey S.; Kankam, M. David; Santiago, Walter; Madi, Frank J.
1992-01-01
A test facility at LeRC was assembled for evaluating free-piston Stirling engine/linear alternator control options, and interaction with various electrical loads. This facility is based on a 'SPIKE' engine/alternator. The engine/alternator, a multi-purpose load system, a digital computer based load and facility control, and a data acquisition system with both steady-periodic and transient capability are described. Preliminary steady-periodic results are included for several operating modes of a digital AC parasitic load control. Preliminary results on the transient response to switching a resistive AC user load are discussed.
Borjigin, Sumuya; Yang, Yating; Yang, Xiaoguang; Sun, Leilei
2018-03-01
Many researchers have realized that there is a strong correlation between stock prices and macroeconomy. In order to make this relationship clear, a lot of studies have been done. However, the causal relationship between stock prices and macroeconomy has still not been well explained. A key point is that, most of the existing research adopts linear and stable models to investigate the correlation of stock prices and macroeconomy, while the real causality of that may be nonlinear and dynamic. To fill this research gap, we investigate the nonlinear and dynamic causal relationships between stock prices and macroeconomy. Based on the case of China's stock prices and acroeconomy measures from January 1992 to March 2017, we compare the linear Granger causality test models with nonlinear ones. Results demonstrate that the nonlinear dynamic Granger causality is much stronger than linear Granger causality. From the perspective of nonlinear dynamic Granger causality, China's stock prices can be viewed as "national economic barometer". On the one hand, this study will encourage researchers to take nonlinearity and dynamics into account when they investigate the correlation of stock prices and macroeconomy; on the other hand, our research can guide regulators and investors to make better decisions.
Kim, Seunggyu; Lee, Seokhun; Jeon, Jessie S.
2017-11-01
To determine the most effective antimicrobial treatments of infectious pathogen, high-throughput antibiotic susceptibility test (AST) is critically required. However, the conventional AST requires at least 16 hours to reach the minimum observable population. Therefore, we developed a microfluidic system that allows maintenance of linear antibiotic concentration and measurement of local bacterial density. Based on the Stokes-Einstein equation, the flow rate in the microchannel was optimized so that linearization was achieved within 10 minutes, taking into account the diffusion coefficient of each antibiotic in the agar gel. As a result, the minimum inhibitory concentration (MIC) of each antibiotic against P. aeruginosa could be immediately determined 6 hours after treatment of the linear antibiotic concentration. In conclusion, our system proved the efficacy of a high-throughput AST platform through MIC comparison with Clinical and Laboratory Standards Institute (CLSI) range of antibiotics. This work was supported by the Climate Change Research Hub (Grant No. N11170060) of the KAIST and by the Brain Korea 21 Plus project.
Managing Reverse Logistics or Reversing Logistics Management?
Brito, Marisa
2004-01-01
textabstractIn the past, supply chains were busy fine-tuning the logistics from raw material to the end customer. Today an increasing flow of products is going back in the chain. Thus, companies have to manage reverse logistics as well.This thesis contributes to a better understanding of reverse logistics. The thesis brings insights on reverse logistics decision-making and it lays down theoretical principles for reverse logistics as a research field.In particular it puts together a framework ...
Yoo, Yun Joo; Sun, Lei; Poirier, Julia G; Paterson, Andrew D; Bull, Shelley B
2017-02-01
By jointly analyzing multiple variants within a gene, instead of one at a time, gene-based multiple regression can improve power, robustness, and interpretation in genetic association analysis. We investigate multiple linear combination (MLC) test statistics for analysis of common variants under realistic trait models with linkage disequilibrium (LD) based on HapMap Asian haplotypes. MLC is a directional test that exploits LD structure in a gene to construct clusters of closely correlated variants recoded such that the majority of pairwise correlations are positive. It combines variant effects within the same cluster linearly, and aggregates cluster-specific effects in a quadratic sum of squares and cross-products, producing a test statistic with reduced degrees of freedom (df) equal to the number of clusters. By simulation studies of 1000 genes from across the genome, we demonstrate that MLC is a well-powered and robust choice among existing methods across a broad range of gene structures. Compared to minimum P-value, variance-component, and principal-component methods, the mean power of MLC is never much lower than that of other methods, and can be higher, particularly with multiple causal variants. Moreover, the variation in gene-specific MLC test size and power across 1000 genes is less than that of other methods, suggesting it is a complementary approach for discovery in genome-wide analysis. The cluster construction of the MLC test statistics helps reveal within-gene LD structure, allowing interpretation of clustered variants as haplotypic effects, while multiple regression helps to distinguish direct and indirect associations. © 2016 The Authors Genetic Epidemiology Published by Wiley Periodicals, Inc.
Xia, Yin; Cai, Tianxi; Cai, T Tony
2018-01-01
Motivated by applications in genomics, we consider in this paper global and multiple testing for the comparisons of two high-dimensional linear regression models. A procedure for testing the equality of the two regression vectors globally is proposed and shown to be particularly powerful against sparse alternatives. We then introduce a multiple testing procedure for identifying unequal coordinates while controlling the false discovery rate and false discovery proportion. Theoretical justifications are provided to guarantee the validity of the proposed tests and optimality results are established under sparsity assumptions on the regression coefficients. The proposed testing procedures are easy to implement. Numerical properties of the procedures are investigated through simulation and data analysis. The results show that the proposed tests maintain the desired error rates under the null and have good power under the alternative at moderate sample sizes. The procedures are applied to the Framingham Offspring study to investigate the interactions between smoking and cardiovascular related genetic mutations important for an inflammation marker.
Suttida Rakkapao
2016-10-01
Full Text Available This study investigated the multiple-choice test of understanding of vectors (TUV, by applying item response theory (IRT. The difficulty, discriminatory, and guessing parameters of the TUV items were fit with the three-parameter logistic model of IRT, using the parscale program. The TUV ability is an ability parameter, here estimated assuming unidimensionality and local independence. Moreover, all distractors of the TUV were analyzed from item response curves (IRC that represent simplified IRT. Data were gathered on 2392 science and engineering freshmen, from three universities in Thailand. The results revealed IRT analysis to be useful in assessing the test since its item parameters are independent of the ability parameters. The IRT framework reveals item-level information, and indicates appropriate ability ranges for the test. Moreover, the IRC analysis can be used to assess the effectiveness of the test’s distractors. Both IRT and IRC approaches reveal test characteristics beyond those revealed by the classical analysis methods of tests. Test developers can apply these methods to diagnose and evaluate the features of items at various ability levels of test takers.
Development and tests of fast 1-MA linear transformer driver stages
A. A. Kim
2009-05-01
Full Text Available In this article we present the design and test results of the most powerful, fast linear transformer driver (LTD stage developed to date. This 1-MA LTD stage consists of 40 parallel RLC (resistor R, inductor L, and capacitor C circuits called “bricks” that are triggered simultaneously; it is able to deliver ∼1 MA current pulse with a rise time of ∼100 ns into the ∼0.1-Ohm matched load. The electrical behavior of the stage can be predicted by using a simple RLC circuit, thus simplifying the designing of various LTD-based accelerators. Five 1-MA LTD stages assembled in series into a module have been successfully tested with both resistive and vacuum electron-beam diode loads.
TBM performance prediction in Yucca Mountain welded tuff from linear cutter tests
Gertsch, R.; Ozdemir, L.; Gertsch, L.
1992-01-01
This paper discusses performance prediction which were developed for tunnel boring machines operating in welded tuff for the construction of the experimental study facility and the potential nuclear waste repository at Yucca Mountain. The predictions were based on test data obtained from an extensive series of linear cutting tests performed on samples of Topopah String welded tuff from the Yucca Mountain Project site. Using the cutter force, spacing, and penetration data from the experimental program, the thrust, torque, power, and rate of penetration were estimated for a 25 ft diameter tunnel boring machine (TBM) operating in welded tuff. The result show that the Topopah Spring welded tuff (TSw2) can be excavated at relatively high rates of advance with state-of-the-art TBMs. The result also show, however, that the TBM torque and power requirements will be higher than estimated based on rock physical properties and past tunneling experience in rock formations of similar strength
Test of the linear-no threshold theory of radiation carcinogenesis
Cohen, B.L.
1994-01-01
We recently completed a compilation of radon measurements from available sources which gives the average radon level, in homes for 1730 counties, well over half of all U.S. counties and comprising about 90% of the total U.S. population. Epidemiologists normally study the relationship between mortality risks to individuals, m, vs their personal exposure, r, whereas an ecological study like ours deals with the relationship between the average risk to groups of individuals (population of counties) and their average exposure. It is well known to epidemiologists that, in general, the average dose does not determine the average risk, and to assume otherwise is called 'the ecological fallacy'. However, it is easy to show that, in testing a linear-no threshold theory, 'the ecological fallacy' does not apply; in that theory, the average dose does determine the average risk. This is widely recognized from the fact that 'person-rem' determines the number of deaths. Dividing person-rem by population gives average dose, and dividing number of deaths by population gives mortality rate. Because of the 'ecological fallacy', epidemiology textbooks often state that an ecological study cannot determine a causal relationship between risk and exposure. That may be true, but it is irrelevant here because the purpose of our study is not to determine a causal relationship; it is rather to test the linear-no threshold dependence of m on r. (author)
Mazo Lopera, Mauricio A; Coombes, Brandon J; de Andrade, Mariza
2017-09-27
Gene-environment (GE) interaction has important implications in the etiology of complex diseases that are caused by a combination of genetic factors and environment variables. Several authors have developed GE analysis in the context of independent subjects or longitudinal data using a gene-set. In this paper, we propose to analyze GE interaction for discrete and continuous phenotypes in family studies by incorporating the relatedness among the relatives for each family into a generalized linear mixed model (GLMM) and by using a gene-based variance component test. In addition, we deal with collinearity problems arising from linkage disequilibrium among single nucleotide polymorphisms (SNPs) by considering their coefficients as random effects under the null model estimation. We show that the best linear unbiased predictor (BLUP) of such random effects in the GLMM is equivalent to the ridge regression estimator. This equivalence provides a simple method to estimate the ridge penalty parameter in comparison to other computationally-demanding estimation approaches based on cross-validation schemes. We evaluated the proposed test using simulation studies and applied it to real data from the Baependi Heart Study consisting of 76 families. Using our approach, we identified an interaction between BMI and the Peroxisome Proliferator Activated Receptor Gamma ( PPARG ) gene associated with diabetes.
Fungible weights in logistic regression.
Jones, Jeff A; Waller, Niels G
2016-06-01
In this article we develop methods for assessing parameter sensitivity in logistic regression models. To set the stage for this work, we first review Waller's (2008) equations for computing fungible weights in linear regression. Next, we describe 2 methods for computing fungible weights in logistic regression. To demonstrate the utility of these methods, we compute fungible logistic regression weights using data from the Centers for Disease Control and Prevention's (2010) Youth Risk Behavior Surveillance Survey, and we illustrate how these alternate weights can be used to evaluate parameter sensitivity. To make our work accessible to the research community, we provide R code (R Core Team, 2015) that will generate both kinds of fungible logistic regression weights. (PsycINFO Database Record (c) 2016 APA, all rights reserved).
Reliability and Usefulness of Linear Sprint Testing in Adolescent Rugby Union and League Players.
Darrall-Jones, Joshua D; Jones, Ben; Roe, Gregory; Till, Kevin
2016-05-01
The purpose of this study was to evaluate (a) whether there were differences in sprint times at 5, 10, 20, 30, and 40 m between rugby union and rugby league players, (b) determine the reliability and usefulness of linear sprint testing in adolescent rugby players. Data were collected on 28 rugby union and league academy players over 2 testing sessions, with 3-day rest between sessions. Rugby league players were faster at 5 m than rugby union players, with further difference unclear. Sprint time at 10, 20, 30, and 40 m was all reliable (coefficient of variation [CV] = 3.1, 1.8, 2.0, and 1.3%) but greater than the smallest worthwhile change (SWC [0.2 × between-subject SD]), rating the test as marginal for usefulness. Although the test was incapable of detecting the SWC, we recommend that practitioners and researchers use Hopkins' proposed method; whereby plotting the change score of the individual at each split (±typical error [TE] expressed as a CV) against the SWC and visually inspecting whether the TE crosses into the SWC are capable of identifying whether a change is both real (greater than the noise of the test, i.e., >TE) and of practical significance (>SWC). Researchers and practitioners can use the TE and SWC from this study to assess changes in performance of adolescent rugby players when using single beam timing gates.
LOGISTICS OPTIMIZATION USING ONTOLOGIES
Hendi , Hayder; Ahmad , Adeel; Bouneffa , Mourad; Fonlupt , Cyril
2014-01-01
International audience; Logistics processes involve complex physical flows and integration of different elements. It is widely observed that the uncontrolled processes can decline the state of logistics. The optimization of logistic processes can support the desired growth and consistent continuity of logistics. In this paper, we present a software framework for logistic processes optimization. It primarily defines logistic ontologies and then optimize them. It intends to assist the design of...
Management of Logistics Planning
Bjørnar Aas; Stein W. Wallace
2010-01-01
Logistics problems are gradually becoming more complex and a better understanding of logistics management as a subject is a key to deal with the new challenges. A core element of logistics management is logistics planning, which substitutes for low customer service levels, high waste, and the use of buffers and slacks in the execution of logistic activities. Furthermore, the availability of information and problem-solving capabilities are established as the core parts of logistics planning. B...
Complex logistics audit system
Zuzana Marková
2010-02-01
Full Text Available Complex logistics audit system is a tool for realization of logistical audit in the company. The current methods for logistics auditare based on “ad hok” analysis of logisticsl system. This paper describes system for complex logistics audit. It is a global diagnosticsof logistics processes and functions of enterprise. The goal of logistics audit is to provide comparative documentation for managementabout state of logistics in company and to show the potential of logistics changes in order to achieve more effective companyperformance.
A linear programming algorithm to test for jamming in hard-sphere packings
Donev, Aleksandar; Torquato, Salvatore.; Stillinger, Frank H.; Connelly, Robert
2004-01-01
Jamming in hard-particle packings has been the subject of considerable interest in recent years. In a paper by Torquato and Stillinger [J. Phys. Chem. B 105 (2001)], a classification scheme of jammed packings into hierarchical categories of locally, collectively and strictly jammed configurations has been proposed. They suggest that these jamming categories can be tested using numerical algorithms that analyze an equivalent contact network of the packing under applied displacements, but leave the design of such algorithms as a future task. In this work, we present a rigorous and practical algorithm to assess whether an ideal hard-sphere packing in two or three dimensions is jammed according to the aforementioned categories. The algorithm is based on linear programming and is applicable to regular as well as random packings of finite size with hard-wall and periodic boundary conditions. If the packing is not jammed, the algorithm yields representative multi-particle unjamming motions. Furthermore, we extend the jamming categories and the testing algorithm to packings with significant interparticle gaps. We describe in detail two variants of the proposed randomized linear programming approach to test for jamming in hard-sphere packings. The first algorithm treats ideal packings in which particles form perfect contacts. Another algorithm treats the case of jamming in packings with significant interparticle gaps. This extended algorithm allows one to explore more fully the nature of the feasible particle displacements. We have implemented the algorithms and applied them to ordered as well as random packings of circular disks and spheres with periodic boundary conditions. Some representative results for large disordered disk and sphere packings are given, but more robust and efficient implementations as well as further applications (e.g., non-spherical particles) are anticipated for the future
Testing For The Linearity of Responses To Multiple Anthropogenic Climate Forcings
Forest, C. E.; Stone, P. H.; Sokolov, A. P.
To test whether climate forcings are additive, we compare climate model simulations in which anthropogenic forcings are applied individually and in combination. Tests are performed with different values for climate system properties (climate sensitivity and rate of heat uptake by the deep ocean) as well as for different strengths of the net aerosol forcing, thereby testing for the dependence of linearity on these properties. The MIT 2D Land-Ocean Climate Model used in this study consists of a zonally aver- aged statistical-dynamical atmospheric model coupled to a mixed-layer Q-flux ocean model, with heat anomalies diffused into the deep ocean. Following our previous stud- ies, the anthropogenic forcings are the changes in concentrations of greenhouse gases (1860-1995), sulfate aerosol (1860-1995), and stratospheric and tropospheric ozone (1979-1995). The sulfate aerosol forcing is applied as a surface albedo change. For an aerosol forcing of -1.0 W/m2 and an effective ocean diffusitivity of 2.5 cm2/s, the nonlinearity of the response of global-mean surface temperatures to the combined forcing shows a strong dependence on climate sensitivity. The fractional change in decadal averages ([(TG + TS + TO) - TGSO]/TGSO) for the 1986-1995 period compared to pre-industrial times are 0.43, 0.90, and 1.08 with climate sensitiv- ities of 3.0, 4.5, and 6.2 C, respectively. The values of TGSO for these three cases o are 0.52, 0.62, and 0.76 C. The dependence of linearity on climate system properties, o the role of climate system feedbacks, and the implications for the detection of climate system's response to individual forcings will be presented. Details of the model and forcings can be found at http://web.mit.edu/globalchange/www/.
Significance tests to determine the direction of effects in linear regression models.
Wiedermann, Wolfgang; Hagmann, Michael; von Eye, Alexander
2015-02-01
Previous studies have discussed asymmetric interpretations of the Pearson correlation coefficient and have shown that higher moments can be used to decide on the direction of dependence in the bivariate linear regression setting. The current study extends this approach by illustrating that the third moment of regression residuals may also be used to derive conclusions concerning the direction of effects. Assuming non-normally distributed variables, it is shown that the distribution of residuals of the correctly specified regression model (e.g., Y is regressed on X) is more symmetric than the distribution of residuals of the competing model (i.e., X is regressed on Y). Based on this result, 4 one-sample tests are discussed which can be used to decide which variable is more likely to be the response and which one is more likely to be the explanatory variable. A fifth significance test is proposed based on the differences of skewness estimates, which leads to a more direct test of a hypothesis that is compatible with direction of dependence. A Monte Carlo simulation study was performed to examine the behaviour of the procedures under various degrees of associations, sample sizes, and distributional properties of the underlying population. An empirical example is given which illustrates the application of the tests in practice. © 2014 The British Psychological Society.
ALICE EMCal Reconstructable Energy Non-Linearity From Test Beam Monte Carlo
Carter, Thomas Michael
2017-01-01
Calorimeters play many important roles in modern high energy physics detectors, such as event selection, triggering, and precision energy measurements. EMCal, in the case of the ALICE experiment provides triggering on high energy jets, improves jet quenching study measurement bias and jet energy resolution, and improves electron and photon measurements [3]. With the EMCal detector in the ALICE experiment taking on so many important roles, it is important to fully understand, characterize and model its interactions with particles. In 2010 SPS and PS electron test beam measurements were performed on an EMCal mini-module [2]. Alongside this, the test beam setup and geometry was recreated in Geant4 by Nico [1]. Figure 1 shows the reconstructable energy linearity for the SPS test beam data and that obtained from the test beam monte carlo, indicating the amount of energy deposit as hits in the EMCal module. It can be seen that for energies above ∼ 100 GeV there is a signiﬁcant drop in the reconstructableenergym...
A test of the linear-no threshold theory of radiation carcinogenesis
Cohen, B.L.
1990-01-01
It has been pointed out that, while an ecological study cannot determine whether radon causes lung cancer, it can test the validity of a linear-no threshold relationship between them. The linear-no threshold theory predicts a substantial positive correlation between the average radon exposure in various counties and their lung cancer mortality rates. Data on living areas of houses in 411 counties from all parts of the United States exhibit, rather, a substantial negative correlation with the slopes of the lines of regression differing from zero by 10 and 7 standard deviations for males and females, respectively, and from the positive slope predicted by the theory by at least 16 and 12 standard deviations. When the data are segmented into 23 groups of states or into 7 regions of the country, the predominantly negative slopes and correlations persist, applying to 18 of the 23 state groups and 6 of the 7 regions. Five state-sponsored studies are analyzed, and four of these give a strong negative slope (the other gives a weak positive slope, in agreement with our data for that state). A strong negative slope is also obtained in our data on basements in 253 counties. A random selection-no charge study of 39 high and low lung cancer counties (+4 low population states) gives a much stronger negative correlation. When nine potential confounding factors are included in a multiple linear regression analysis, the discrepancy with theory is reduced only to 12 and 8.5 standard deviations for males and females, respectively. When the data are segmented into four groups by population, the multiple regression vs radon level gives a strong negative slope for each of the four groups. Other considerations are introduced to reduce the discrepancy, but it remains very substantial
Test of the linear-no threshold theory of radiation carcinogenesis for inhaled radon decay products
Cohen, B.L.
1995-01-01
Data on lung cancer mortality rates vs. average radon concentration in homes for 1,601 U.S. counties are used to test the linear-no threshold theory. The widely recognized problems with ecological studies, as applied to this work, are addressed extensively. With or without corrections for variations in smoking prevalence, there is a strong tendency for lung cancer rates to decrease with increasing radon exposure, in sharp contrast to the increase expected from the theory. The discrepancy in slope is about 20 standard deviations. It is shown that uncertainties in lung cancer rates, radon exposures, and smoking prevalence are not important and that confounding by 54 socioeconomic factors, by geography, and by altitude and climate can explain only a small fraction of the discrepancy. Effects of known radon-smoking prevalence correlations - rural people have higher radon levels and smoke less than urban people, and smokers are exposed to less radon than non-smokers - are calculated and found to be trivial. In spite of extensive efforts, no potential explanation for the discrepancy other than failure of the linear-no threshold theory for carcinogenesis from inhaled radon decay products could be found. (author)
Expanded studies of linear collider final focus systems at the Final Focus Test Beam
Tenenbaum, P.G.
1995-12-01
In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research
Expanded studies of linear collider final focus systems at the Final Focus Test Beam
Tenenbaum, Peter Gregory [Stanford Univ., CA (United States)
1995-12-01
In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research.
Hilbe, Joseph M
2009-01-01
This book really does cover everything you ever wanted to know about logistic regression … with updates available on the author's website. Hilbe, a former national athletics champion, philosopher, and expert in astronomy, is a master at explaining statistical concepts and methods. Readers familiar with his other expository work will know what to expect-great clarity.The book provides considerable detail about all facets of logistic regression. No step of an argument is omitted so that the book will meet the needs of the reader who likes to see everything spelt out, while a person familiar with some of the topics has the option to skip "obvious" sections. The material has been thoroughly road-tested through classroom and web-based teaching. … The focus is on helping the reader to learn and understand logistic regression. The audience is not just students meeting the topic for the first time, but also experienced users. I believe the book really does meet the author's goal … .-Annette J. Dobson, Biometric...
Sadorra, Mark; LaMere, Brandon J.; Kail, Randi; Aldrich, Carrie; Kinney, Walter; Fetterman, Barbara; Lorey, Thomas; Schiffman, Mark; Castle, Philip E.
2012-01-01
The cobas human papillomavirus (HPV) test (cobas) was recently approved by the U.S. Food and Drug Administration (FDA) and identifies HPV16 and HPV18 separately as well as detecting a pool of 11 HR-HPV genotypes (HPV31, -33, -35, -39, -45, -51, -52, -56, -58, -59, -68) and also HPV66. We compared cobas, Linear Array (LA), and Hybrid Capture 2 (HC2) assays for detection of carcinogenic HPV DNA, and cobas and LA for detection of HPV16 and HPV18 DNA, among the first 1,852 women enrolled in the HPV Persistence and Progression Cohort (PaP Cohort) study. Specimens were tested by all 3 assays 1 year after an HC2-positive result. In 1,824 specimens with cobas results, cobas had an 85.9% agreement with HC2 and 91.0% agreement with LA for carcinogenic HPV detection. When results between cobas and HC2 disagreed, cobas tended to call more women HPV positive (P < 0.01). Categorizing cobas and LA results hierarchically according to cancer risk (HPV16, HPV18, other carcinogenic HPV genotypes, or carcinogen negative), there was a 90% agreement for all categories of HPV (n = 1,824). We found good agreement between the two U.S. FDA-approved HPV tests, with discrepancies between the two assays due to specific characteristics of the individual assays. Additional studies are needed to compare HC2 and cobas for detecting and predicting CIN3 to understand the clinical implications of the discrepant test results between the two tests. PMID:22075592
Madan, Jason; Lönnroth, Knut; Laokri, Samia; Squire, Stephen Bertel
2015-10-22
Tuberculosis (TB) is a major global public health problem which affects poorest individuals the worst. A high proportion of patients incur 'catastrophic costs' which have been shown to result in severe financial hardship and adverse health outcomes. Data on catastrophic cost incidence is not routinely collected, and current definitions of this indicator involve several practical and conceptual barriers to doing so. We analysed data from TB programmes in India (Bangalore), Bangladesh and Tanzania to determine whether dissaving (the sale of assets or uptake of loans) is a useful indicator of financial hardship. Data were obtained from prior studies of TB patient costs in Bangladesh (N = 96), Tanzania (N = 94) and Bangalore (N = 891). These data were analysed using logistic and linear multivariate regression to determine the association between costs (absolute and relative to income) and both the presence of dissaving and the amounts dissaved. After adjusting for covariates such as age, sex and rural/urban location, we found a significant positive association between the occurrence of dissaving and total costs incurred in Tanzania and Bangalore. We further found that, for patients in Bangalore an increase in dissaving of $10 USD was associated with an increase in the cost-income ratio of 0.10 (p costs of $7 USD (p costs that does not require usage of complex patient cost questionnaires. It also offers an informative indicator of financial hardship in its own right, and could therefore play an important role as an indicator to monitor and evaluate the impact of financial protection and service delivery interventions in reducing hardship and facilitating universal health coverage. Further research is required to understand the patterns and types of dissaving that have the strongest relationship with financial hardship and clinical outcomes in order to move toward evidence-based policy making.
Foster, Guy M.; Graham, Jennifer L.
2016-04-06
The Kansas River is a primary source of drinking water for about 800,000 people in northeastern Kansas. Source-water supplies are treated by a combination of chemical and physical processes to remove contaminants before distribution. Advanced notification of changing water-quality conditions and cyanobacteria and associated toxin and taste-and-odor compounds provides drinking-water treatment facilities time to develop and implement adequate treatment strategies. The U.S. Geological Survey (USGS), in cooperation with the Kansas Water Office (funded in part through the Kansas State Water Plan Fund), and the City of Lawrence, the City of Topeka, the City of Olathe, and Johnson County Water One, began a study in July 2012 to develop statistical models at two Kansas River sites located upstream from drinking-water intakes. Continuous water-quality monitors have been operated and discrete-water quality samples have been collected on the Kansas River at Wamego (USGS site number 06887500) and De Soto (USGS site number 06892350) since July 2012. Continuous and discrete water-quality data collected during July 2012 through June 2015 were used to develop statistical models for constituents of interest at the Wamego and De Soto sites. Logistic models to continuously estimate the probability of occurrence above selected thresholds were developed for cyanobacteria, microcystin, and geosmin. Linear regression models to continuously estimate constituent concentrations were developed for major ions, dissolved solids, alkalinity, nutrients (nitrogen and phosphorus species), suspended sediment, indicator bacteria (Escherichia coli, fecal coliform, and enterococci), and actinomycetes bacteria. These models will be used to provide real-time estimates of the probability that cyanobacteria and associated compounds exceed thresholds and of the concentrations of other water-quality constituents in the Kansas River. The models documented in this report are useful for characterizing changes
Physics goals for the planned next linear collider engineering test facility
Bohn, C.; Michelotti, L.; Ostiguy, J.-F.; Syphers, M.; Bluem, H.; Todd, A.; Gai, W.; Power, J.; Simpson, J.; Raubenheimer, T.
2001-01-01
The Next Linear Collider (NLC) Collaboration is planning to construct an Engineering Test Facility (ETF) at Fermilab. As presently envisioned, the ETF would comprise a fundamental unit of the NLC main linac to include X-band klystrons and modulators, a delay-line power-distribution system (DLDS), and NLC accelerating structures that serve as loads. The principal purpose of the ETF is to validate stable operation of the power-distribution system, first without beam, then with a beam having the NLC pulse structure. This paper concerns the possibility of configuring and using the ETF to accelerate beam with an NLC pulse structure, as well as of doing experiments to measure beam-induced wakefields in the rf structures and their influence back on the beam
Physics Goals for the Planned Next Linear Collider Engineering Test Facility
Raubenheimer, Tor O
2001-01-01
The Next Linear Collider (NLC) Collaboration is planning to construct an Engineering Test Facility (ETF) at Fermilab. As presently envisioned, the ETF would comprise a fundamental unit of the NLC main linac to include X-band klystrons and modulators, a delay-line power-distribution system (DLDS), and NLC accelerating structures that serve as loads. The principal purpose of the ETF is to validate stable operation of the power distribution system, first without beam, then with a beam having the NLC pulse structure. This paper concerns the possibility of configuring and using the ETF to accelerate beam with an NLC pulse structure, as well as of doing experiments to measure beam-induced wakefields in the rf structures and their influence back on the beam
600 kV modulator design for the SLAC Next Linear Collider Test Accelerator
Harris, K.; de Lamare, J.; Nesterov, V.; Cassel, R.
1992-07-01
Preliminary design for the SLAC Next Linear Collider Test Accelerator (NLCTA) requires a pulse power source to produce a 600 kV, 600 A, 1.4 μs, 0.1% flat top pulse with rise and fall times of approximately 100 ns to power an X-Band klystron with a microperveance of 1.25 at ∼ 100 MW peak RF power. The design goals for the modulator, including those previously listed, are peak modulator pulse power of 340 MW operating at 120 Hz. A three-stage darlington pulse-forming network, which produces a >100 kV, 1.4 μs pulse, is coupled to the klystron load through a 6:1 pulse transformer. Careful consideration of the transformer leakage inductance, klystron capacitance, system layout, and component choice is necessary to produce the very fast rise and fall times at 600 kV operating continuously at 120 Hz
A further test of the linearity of temporal summation in forward masking.
Plack, Christopher J; Carcagno, Samuele; Oxenham, Andrew J
2007-10-01
An experiment tested the hypothesis that the masking effects of two nonoverlapping forward maskers are summed linearly over time. First, the levels of individual noise maskers required to mask a brief 4-kHz signal presented at 10-, 20-, 30-, or 40-dB sensation level (SL) were found. The hypothesis predicts that a combination of the first masker presented at the level required to mask the 10-dB SL signal and the second masker presented at the level required to mask the 20-dB SL signal, should produce the same amount of masking as the converse situation (i.e., the first masker presented at the level required to mask the 20-dB SL signal and the second masker presented at the level required to mask the 10-dB SL signal), and similarly for the 30- and 40-dB SL signals. The results were consistent with the predictions.
Linear Aerospike SR-71 Experiment (LASRE) dumps water after first in-flight cold flow test
1998-01-01
The NASA SR-71A successfully completed its first cold flow flight as part of the NASA/Rocketdyne/Lockheed Martin Linear Aerospike SR-71 Experiment (LASRE) at NASA's Dryden Flight Research Center, Edwards, California on March 4, 1998. During a cold flow flight, gaseous helium and liquid nitrogen are cycled through the linear aerospike engine to check the engine's plumbing system for leaks and to check the engine operating characterisitics. Cold-flow tests must be accomplished successfully before firing the rocket engine experiment in flight. The SR-71 took off at 10:16 a.m. PST. The aircraft flew for one hour and fifty-seven minutes, reaching a maximum speed of Mach 1.58 before landing at Edwards at 12:13 p.m. PST. 'I think all in all we had a good mission today,' Dryden LASRE Project Manager Dave Lux said. Flight crew member Bob Meyer agreed, saying the crew 'thought it was a really good flight.' Dryden Research Pilot Ed Schneider piloted the SR-71 during the mission. Lockheed Martin LASRE Project Manager Carl Meade added, 'We are extremely pleased with today's results. This will help pave the way for the first in-flight engine data-collection flight of the LASRE.' The LASRE experiment was designed to provide in-flight data to help Lockheed Martin evaluate the aerodynamic characteristics and the handling of the SR-71 linear aerospike experiment configuration. The goal of the project was to provide in-flight data to help Lockheed Martin validate the computational predictive tools it was using to determine the aerodynamic performance of a future reusable launch vehicle. The joint NASA, Rocketdyne (now part of Boeing), and Lockheed Martin Linear Aerospike SR-71 Experiment (LASRE) completed seven initial research flights at Dryden Flight Research Center. Two initial flights were used to determine the aerodynamic characteristics of the LASRE apparatus (pod) on the back of the SR-71. Five later flights focused on the experiment itself. Two were used to cycle gaseous
Testing nonlinear-QED at the future linear collider with an intense laser
Hartin, Anthony; Porto, Stefano; Moortgat-Pick, Gudrid; Hamburg Univ.
2014-04-01
The future linear collider will collide dense e + e - bunches at high energies up to 1 TeV, generating very intense electromagnetic fields at the interaction point (IP). These fields are strong enough to lead to nonlinear effects which affect all IP processes and which are described by strong field physics theory. In order to test this theory, we propose an experiment that will focus an intense laser on the LC electron beam post-IP. Similar experiments at SLAC E144 have investigated nonlinear Compton scattering, Breit-Wheeler pair production using an electron beam of 46.6 GeV. The higher beam energies available at the future LC would allow more precise studies of these phenomena. Mass-shift and spin-dependent effects could also be investigated.
Confirm calculation of 12 MeV non-destructive testing electron linear accelerator target
Ma Shudong; Zhang Rutong; Guo Yanbin; Zhou Yuan; Li Xuexian; Chen Yan
2012-01-01
The confirm calculation of 12 MeV non-destructive testing (NDT) electron linear accelerator (LINAC) target was studied. Firstly, the most optimal target thickness and related photon dose yield, distributions of dose rate, and related photon conversion efficiencies were got by calculation with specific analysis of the physical mechanism of the interactions between the beam and target; Secondly, the photon dose rate distribution, converter efficiencies, and thickness of various kinds of targets, such as W, Au, Ta, etc. were verified by MCNP simulation and the most optimal target was got using the MCNP code; Lastly, the calculation results of theory and MCNP were compared to confirm the validity of target calculation. (authors)
Fasmer, Ole Bernt; Mjeldheim, Kristin; Førland, Wenche; Hansen, Anita L; Syrstad, Vigdis Elin Giæver; Oedegaard, Ketil J; Berle, Jan Øystein
2016-08-11
Attention Deficit Hyperactivity Disorder (ADHD) is a heterogeneous disorder. Therefore it is important to look for factors that can contribute to better diagnosis and classification of these patients. The aims of the study were to characterize adult psychiatric out-patients with a mixture of mood, anxiety and attentional problems using an objective neuropsychological test of attention combined with an assessment of mood instability. Newly referred patients (n = 99; aged 18-65 years) requiring diagnostic evaluation of ADHD, mood or anxiety disorders were recruited, and were given a comprehensive diagnostic evaluation including the self-report form of the cyclothymic temperament scale and Conner's Continuous Performance Test II (CPT-II). In addition to the traditional measures from this test we have extracted raw data and analysed time series using linear and non-linear mathematical methods. Fifty patients fulfilled criteria for ADHD, while 49 did not, and were given other psychiatric diagnoses (clinical controls). When compared to the clinical controls the ADHD patients had more omission and commission errors, and higher reaction time variability. Analyses of response times showed higher values for skewness in the ADHD patients, and lower values for sample entropy and symbolic dynamics. Among the ADHD patients 59 % fulfilled criteria for a cyclothymic temperament, and this group had higher reaction time variability and lower scores on complexity than the group without this temperament. The CPT-II is a useful instrument in the assessment of ADHD in adult patients. Additional information from this test was obtained by analyzing response times using linear and non-linear methods, and this showed that ADHD patients with a cyclothymic temperament were different from those without this temperament.
Gertsch, R.; Ozdemir, L.
1992-09-01
The performances of mechanical excavators are predicted for excavations in welded tuff. Emphasis is given to tunnel boring machine evaluations based on linear cutting machine test data obtained on samples of Topopah Spring welded tuff. The tests involve measurement of forces as cutters are applied to the rock surface at certain spacing and penetrations. Two disc and two point-attack cutters representing currently available technology are thus evaluated. The performance predictions based on these direct experimental measurements are believed to be more accurate than any previous values for mechanical excavation of welded tuff. The calculations of performance are predicated on minimizing the amount of energy required to excavate the welded tuff. Specific energy decreases with increasing spacing and penetration, and reaches its lowest at the widest spacing and deepest penetration used in this test program. Using the force, spacing, and penetration data from this experimental program, the thrust, torque, power, and rate of penetration are calculated for several types of mechanical excavators. The results of this study show that the candidate excavators will require higher torque and power than heretofore estimated
Quinino, Roberto C.; Reis, Edna A.; Bessegato, Lupercio F.
2013-01-01
This article proposes the use of the coefficient of determination as a statistic for hypothesis testing in multiple linear regression based on distributions acquired by beta sampling. (Contains 3 figures.)
Rogério de Ávila Ribeiro Junqueira
2006-12-01
Full Text Available A produção de sementes de milho envolve uma cadeia de produção agroindustrial complexa cujos agentes devem primar por oferecer produtos de alta qualidade a um baixo custo para se manterem competitivos no mercado. Neste trabalho, um modelo de otimização linear é proposto para auxiliar nas decisões do planejamento tático da produção, estocagem e transporte de sementes de milho, de forma a minimizar custos de produção, logísticos e fiscais, atendendo às restrições de programação da colheita, capacidade das plantas e demanda dos clientes. Para verificar a coerência do modelo e validar a abordagem, o modelo foi implementado na linguagem de modelagem GAMS e aplicado para resolver diferentes cenários de um exemplo baseado em dados realistas de uma empresa. Os resultados mostraram a importância de se considerar os custos fiscais de ICMS no planejamento agregado da produção e logística de sementes de milho.The production of corn seeds involves a complex agro-industrial production chain whose main agents must offer products of high quality and low price to stay competitive in the market. This work proposes a linear optimization model to support decisions in the tactical planning of production, storing and transportation of corn seeds, designed to minimize production, logistics and tax costs and to satisfy crop planning, plant capacity and client demand constraints. In order to verify the consistency of the model and validate the approach, the model was implemented in the GAMS modeling language and applied to solve different scenarios of an example based on realistic data of a company. The results showed the importance of considering tax costs in the production and logistics aggregate planning of corn seeds.
Slats, P.A.; Bhola, B.; Evers, J.J.M.; Dijkhuizen, G.
1995-01-01
Logistic chain modelling is very important in improving the overall performance of the total logistic chain. Logistic models provide support for a large range of applications, such as analysing bottlenecks, improving customer service, configuring new logistic chains and adapting existing chains to
Managing Reverse Logistics or Reversing Logistics Management?
M.P. de Brito (Marisa)
2004-01-01
textabstractIn the past, supply chains were busy fine-tuning the logistics from raw material to the end customer. Today an increasing flow of products is going back in the chain. Thus, companies have to manage reverse logistics as well.This thesis contributes to a better understanding of reverse
SEPARATION PHENOMENA LOGISTIC REGRESSION
Ikaro Daniel de Carvalho Barreto
2014-03-01
Full Text Available This paper proposes an application of concepts about the maximum likelihood estimation of the binomial logistic regression model to the separation phenomena. It generates bias in the estimation and provides different interpretations of the estimates on the different statistical tests (Wald, Likelihood Ratio and Score and provides different estimates on the different iterative methods (Newton-Raphson and Fisher Score. It also presents an example that demonstrates the direct implications for the validation of the model and validation of variables, the implications for estimates of odds ratios and confidence intervals, generated from the Wald statistics. Furthermore, we present, briefly, the Firth correction to circumvent the phenomena of separation.
Pease, R.L.; Brown, D.B.; Cohn, L.
1997-01-01
A hardness assurance test approach has been developed for bipolar linear circuits and devices in space. It consists of a screen for dose rate sensitivity and a characterization test method to develop the conditions for a lot acceptance test at high dose rate
Popov–Belevitch–Hautus type tests for the controllability of linear complementarity systems
Camlibel, M. Kanat
2007-01-01
It is well-known that checking certain controllability properties of very simple piecewise linear systems are undecidable problems. This paper deals with the controllability problem of a class of piecewise linear systems, known as linear complementarity systems. By exploiting the underlying
Hung, J.; Chaitman, B.R.; Lam, J.; Lesperance, J.; Dupras, G.; Fines, P.; Cherkaoui, O.; Robert, P.; Bourassa, M.G.
1985-01-01
The incremental diagnostic yield of clinical data, exercise ECG, stress thallium scintigraphy, and cardiac fluoroscopy to predict coronary and multivessel disease was assessed in 171 symptomatic men by means of multiple logistic regression analyses. When clinical variables alone were analyzed, chest pain type and age were predictive of coronary disease, whereas chest pain type, age, a family history of premature coronary disease before age 55 years, and abnormal ST-T wave changes on the rest ECG were predictive of multivessel disease. The percentage of patients correctly classified by cardiac fluoroscopy (presence or absence of coronary artery calcification), exercise ECG, and thallium scintigraphy was 9%, 25%, and 50%, respectively, greater than for clinical variables, when the presence or absence of coronary disease was the outcome, and 13%, 25%, and 29%, respectively, when multivessel disease was studied; 5% of patients were misclassified. When the 37 clinical and noninvasive test variables were analyzed jointly, the most significant variable predictive of coronary disease was an abnormal thallium scan and for multivessel disease, the amount of exercise performed. The data from this study provide a quantitative model and confirm previous reports that optimal diagnostic efficacy is obtained when noninvasive tests are ordered sequentially. In symptomatic men, cardiac fluoroscopy is a relatively ineffective test when compared to exercise ECG and thallium scintigraphy
Linear Array Ultrasonic Testing Of A Thick Concrete Specimens For Non-Destructive Evaluation
Clayton, Dwight A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Khazanovich, Lev [Univ. of Minnesota, Minneapolis, MN (United States); Zammerachi, Mattia [Univ. of Minnesota, Minneapolis, MN (United States); Ezell, N. Dianne Bull [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
2017-04-01
The University of Minnesota and Oak Ridge National Laboratory are collaborating on the design and construction of a concrete specimen with sufficient reinforcement density and cross-sectional size to represent a light water reactor (LWR) containment wall with various defects. The preliminary analysis of the collected data using extended synthetic aperture focussin technique (SAFT) reconstruction indicated a great potential of the ultrasound array technology for locating relatively shallow distresses. However, the resolution and reliability of the analysis is inversely proportional to the defect depth and the amount of reinforcement between the measurement point and the defect location. The objective of this round of testing is to evaluate repeatability of the obtained reconstructions from measurements with different frequencies as well as to examine the effect of the duration of the sending ultrasound signal on the resulting reconstructions. Two series of testing are performed in this study. The objective of the first series is to evaluate repeatability of the measurements and resulting reconstructed images. The measurements use three center frequencies. Five measurements are performed at each location with and without lifting the device. The analysis of the collected data suggested that a linear array ultrasound system can produce reliably repeatable reconstructions using 50 kHz signals for relatively shallow depths (less than 0.5 m). However, for reconstructions at the greater depths the use of lower frequency and/or signal filtering to reduce the effect of signal noise may be required. The objective of the second series of testing is to obtain measurements with various impulse signal durations. The entire grid on the smooth surface is tested with four different various impulse signal durations. An analysis of the resulting extended SAFT reconstructions suggested that Kirchhoff-based migration leads to easier interpreting reconstructions when shorter duration
TRM performance prediction in Yucca Mountain welded tuff from linear cutter tests
Gertsch, R.; Ozdemir, L.; Gertsch, L.
1992-01-01
Performance predictions were developed for tunnel boring machines operating in welded tuff for the construction of the experimental study facility and the potential nuclear waste repository at Yucca Mountain. The predictions were based on test data obtained from an extensive series of linear cutting tests performed on samples of Topopah Spring welded tuff from the Yucca Mountain Project site. Using the cutter force, spacing, and penetration data from the experimental program, the thrust, torque, power, and rate of penetration were estimated for a 25 ft diameter tunnel boring machine (TBM) operating in welded tuff. Guidelines were developed for the optimal design of the TBM cutterhead to achieve high production rates at the lowest possible excavation costs. The results show that the Topopah Spring welded tuff (TSw2) can be excavated at relatively high rates of advance with state-of-the-art TBMs. The results also show, however, that the TBM torque and power requirements will be higher than estimated based on rock physical properties and past tunneling experience in rock formations of similar strength
Standards for Standardized Logistic Regression Coefficients
Menard, Scott
2011-01-01
Standardized coefficients in logistic regression analysis have the same utility as standardized coefficients in linear regression analysis. Although there has been no consensus on the best way to construct standardized logistic regression coefficients, there is now sufficient evidence to suggest a single best approach to the construction of a…
Experimental tests of linear and nonlinear three-dimensional equilibrium models in DIII-D
King, J. D., E-mail: kingjd@fusion.gat.com [Oak Ridge Institute for Science Education, Oak Ridge, Tennessee 37830-8050 (United States); General Atomics, P.O. Box 85608, San Diego, California 92816-5608 (United States); Strait, E. J.; Ferraro, N. M.; Lanctot, M. J.; Paz-Soldan, C.; Turnbull, A. D. [General Atomics, P.O. Box 85608, San Diego, California 92816-5608 (United States); Lazerson, S. A.; Logan, N. C.; Park, J.-K.; Nazikian, R.; Okabayashi, M. [Princeton Plasma Physics Laboratory, P.O. Box 451, Princeton, New Jersey 08543-0451 (United States); Haskey, S. R. [Plasma Research Laboratory, Research School of Physical Sciences and Engineering, The Australia National University, Canberra, Australian Capital Territory 0200 (Australia); Hanson, J. M. [Columbia University, 2960 Broadway, New York, New York 10027 (United States); Liu, Yueqiang [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxfordshire OX14 3DB (United Kingdom); Shiraki, D. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, Tennessee 37831 (United States)
2015-07-15
DIII-D experiments using new detailed magnetic diagnostics show that linear, ideal magnetohydrodynamics (MHD) theory quantitatively describes the magnetic structure (as measured externally) of three-dimensional (3D) equilibria resulting from applied fields with toroidal mode number n = 1, while a nonlinear solution to ideal MHD force balance, using the VMEC code, requires the inclusion of n ≥ 1 to achieve similar agreement. These tests are carried out near ITER baseline parameters, providing a validated basis on which to exploit 3D fields for plasma control development. Scans of the applied poloidal spectrum and edge safety factor confirm that low-pressure, n = 1 non-axisymmetric tokamak equilibria are determined by a single, dominant, stable eigenmode. However, at higher beta, near the ideal kink mode stability limit in the absence of a conducting wall, the qualitative features of the 3D structure are observed to vary in a way that is not captured by ideal MHD.
Gerster, Samuel; Namer, Barbara; Elam, Mikael; Bach, Dominik R
2018-02-01
Skin conductance responses (SCR) are increasingly analyzed with model-based approaches that assume a linear and time-invariant (LTI) mapping from sudomotor nerve (SN) activity to observed SCR. These LTI assumptions have previously been validated indirectly, by quantifying how much variance in SCR elicited by sensory stimulation is explained under an LTI model. This approach, however, collapses sources of variability in the nervous and effector organ systems. Here, we directly focus on the SN/SCR mapping by harnessing two invasive methods. In an intraneural recording experiment, we simultaneously track SN activity and SCR. This allows assessing the SN/SCR relationship but possibly suffers from interfering activity of non-SN sympathetic fibers. In an intraneural stimulation experiment under regional anesthesia, such influences are removed. In this stimulation experiment, about 95% of SCR variance is explained under LTI assumptions when stimulation frequency is below 0.6 Hz. At higher frequencies, nonlinearities occur. In the intraneural recording experiment, explained SCR variance is lower, possibly indicating interference from non-SN fibers, but higher than in our previous indirect tests. We conclude that LTI systems may not only be a useful approximation but in fact a rather accurate description of biophysical reality in the SN/SCR system, under conditions of low baseline activity and sporadic external stimuli. Intraneural stimulation under regional anesthesia is the most sensitive method to address this question. © 2017 The Authors. Psychophysiology published by Wiley Periodicals, Inc. on behalf of Society for Psychophysiological Research.
Test of the linear-no threshold theory of radiation carcinogenesis
Cohen, B.L.
1998-01-01
It is shown that testing the linear-no threshold theory (L-NT) of radiation carcinogenesis is extremely important and that lung cancer resulting from exposure to radon in homes is the best tool for doing this. A study of lung cancer rates vs radon exposure in U.S. Counties, reported in 1975, is reviewed. It shows, with extremely powerful statistics, that lung cancer rates decrease with increasing radon exposure, in sharp contrast to the prediction of L-NT, with a discrepancy of over 20 standard deviations. Very extensive efforts were made to explain an appreciable part of this discrepancy consistently with L-NT, with no success; it was concluded that L-NT fails, grossly exaggerating the cancer risk of low level radiation. Two updating studies reported in 1996 are also reviewed. New updating studies utilizing more recent lung cancer statistics and considering 450 new potential confounding factors are reported. All updates reinforce the previous conclusion, and the discrepancy with L-NT is increased. (author)
RF power source for the compact linear collider test facility (CTF3)
McMonagle, G; Brown, Peter; Carron, G; Hanni, R; Mourier, J; Rossat, G; Syratchev, I V; Tanner, L; Thorndahl, L
2004-01-01
The CERN CTF3 facility will test and demonstrate many vital components of CLIC (Compact Linear Collider). This paper describes the pulsed RF power source at 2998.55 MHz for the drive-beam accelerator (DBA), which produces a beam with an energy of 150 MeV and a current of 3.5 Amps. Where possible, existing equipment from the LEP preinjector, especially the modulators and klystrons, is being used and upgraded to achieve this goal. A high power RF pulse compression system is used at the output of each klystron, which requires sophisticated RF phase programming on the low level side to achieve the required RF pulse. In addition to the 3 GHz system two pulsed RF sources operating at 1.5 GHz are being built. The first is a wide-band, low power, travelling wave tube (TWT) for the subharmonic buncher (SHB) system that produces a train of "phase coded" subpulses as part of the injector scheme. The second is a high power narrow band system to produce 20 MW RF power to the 1.5 GHz RF deflectors in the delay loop situate...
Logistic Fuel Processor Development
Salavani, Reza
2004-01-01
The Air Base Technologies Division of the Air Force Research Laboratory has developed a logistic fuel processor that removes the sulfur content of the fuel and in the process converts logistic fuel...
Knudson, D.L.; Rempe, J.L.; Daw, J.E.
2009-01-01
The United States (U.S.) Department of Energy (DOE) designated the Advanced Test Reactor (ATR) as a National Scientific User Facility (NSUF) in April 2007 to promote nuclear science and technology in the U.S. Given this designation, the ATR is supporting new users from universities, laboratories, and industry as they conduct basic and applied nuclear research and development to advance the nation's energy security needs. A fundamental component of the ATR NSUF program is to develop in-pile instrumentation capable of providing real-time measurements of key parameters during irradiation experiments. Dimensional change is a key parameter that must be monitored during irradiation of new materials being considered for fuel, cladding, and structures in next generation and existing nuclear reactors. Such materials can experience significant changes during high temperature irradiation. Currently, dimensional changes are determined by repeatedly irradiating a specimen for a defined period of time in the ATR and then removing it from the reactor for evaluation. The time and labor to remove, examine, and return irradiated samples for each measurement makes this approach very expensive. In addition, such techniques provide limited data (i.e., only characterizing the end state when samples are removed from the reactor) and may disturb the phenomena of interest. To address these issues, the Idaho National Laboratory (INL) recently initiated efforts to evaluate candidate linear variable displacement transducers (LVDTs) for use during high temperature irradiation experiments in typical ATR test locations. Two nuclear grade LVDT vendor designs were identified for consideration - a smaller diameter design qualified for temperatures up to 350 C and a larger design with capabilities to 500 C. Initial evaluation efforts include collecting calibration data as a function of temperature, long duration testing of LVDT response while held at high temperature, and the assessment of changes
Polzin, K. A.; Pearson, J. B.; Webster, K.; Godfoy, T. J.; Bossard, J. A.
2013-01-01
Results of performance testing of an annular linear induction pump that has been designed for integration into a fission surface power technology demonstration unit are presented. The pump electromagnetically pushes liquid metal (NaK) through a specially-designed apparatus that permits quantification of pump performance over a range of operating conditions. Testing was conducted for frequencies of 40, 55, and 70 Hz, liquid metal temperatures of 125, 325, and 525 C, and input voltages from 30 to 120 V. Pump performance spanned a range of flow rates from roughly 0.3 to 3.1 L/s (4.8 to 49 gpm), and pressure heads of <1 to 104 kPa (<0.15 to 15 psi). The maximum efficiency measured during testing was 5.4%. At the technology demonstration unit operating temperature of 525 C the pump operated over a narrower envelope, with flow rates from 0.3 to 2.75 L/s (4.8 to 43.6 gpm), developed pressure heads from <1 to 55 kPa (<0.15 to 8 psi), and a maximum efficiency of 3.5%. The pump was supplied with three-phase power at 40 and 55 Hz using a variable-frequency motor drive, while power at 55 and 70 Hz was supplied using a variable-frequency power supply. Measured performance of the pump at 55 Hz using either supply exhibited good quantitative agreement. For a given temperature, the peak in efficiency occurred at different flow rates as the frequency was changed, but the maximum value of efficiency was relative insensitive within 0.3% over the frequency range tested, including a scan from 45 to 78 Hz. The objectives of the FSP technology project are as follows:5 • Develop FSP concepts that meet expected surface power requirements at reasonable cost with added benefits over other options. • Establish a nonnuclear hardware-based technical foundation for FSP design concepts to reduce overall development risk. • Reduce the cost uncertainties for FSP and establish greater credibility for flight system cost estimates. • Generate the key nonnuclear products to allow Agency
Reverse logistics - a framework
M.P. de Brito (Marisa); R. Dekker (Rommert)
2002-01-01
textabstractIn this paper we define and compare Reverse Logistics definitions. We start by giving an understanding framework of Reverse Logistics: the why-what-how. By this means, we put in context the driving forces for Reverse Logistics, a typology of return reasons, a classification of
Steadie Seifi, M.; Farahani, R.Z.; Rezapour, S.; Kardar, L.
2011-01-01
Logistics has an important economic role because it swallows the biggest part of capital and supports the flow and movement of many economic transactions. Therefore, designing the best logistics strategies is vital. In this chapter, we take a look at different kinds of logistics decisions,
Soysal, Mehmet; Bloemhof-Ruwaard, Jacqueline M.
2017-01-01
The fast evolution of sustainability leads to the development of a new fast-growing concept called sustainable logistics management. This research addresses recent business trends and challenges in logistics and their implications for sustainable logistics management. Additionally, we discuss policy
Soysal, Mehmet; Bloemhof-Ruwaard, Jacqueline M.
2018-01-01
The fast evolution of sustainability leads to the development of a new fast-growing concept called sustainable logistics management. This research addresses recent business trends and challenges in logistics and their implications for sustainable logistics management. Additionally, we discuss policy
Pradhan, Biswajeet
2010-05-01
This paper presents the results of the cross-validation of a multivariate logistic regression model using remote sensing data and GIS for landslide hazard analysis on the Penang, Cameron, and Selangor areas in Malaysia. Landslide locations in the study areas were identified by interpreting aerial photographs and satellite images, supported by field surveys. SPOT 5 and Landsat TM satellite imagery were used to map landcover and vegetation index, respectively. Maps of topography, soil type, lineaments and land cover were constructed from the spatial datasets. Ten factors which influence landslide occurrence, i.e., slope, aspect, curvature, distance from drainage, lithology, distance from lineaments, soil type, landcover, rainfall precipitation, and normalized difference vegetation index (ndvi), were extracted from the spatial database and the logistic regression coefficient of each factor was computed. Then the landslide hazard was analysed using the multivariate logistic regression coefficients derived not only from the data for the respective area but also using the logistic regression coefficients calculated from each of the other two areas (nine hazard maps in all) as a cross-validation of the model. For verification of the model, the results of the analyses were then compared with the field-verified landslide locations. Among the three cases of the application of logistic regression coefficient in the same study area, the case of Selangor based on the Selangor logistic regression coefficients showed the highest accuracy (94%), where as Penang based on the Penang coefficients showed the lowest accuracy (86%). Similarly, among the six cases from the cross application of logistic regression coefficient in other two areas, the case of Selangor based on logistic coefficient of Cameron showed highest (90%) prediction accuracy where as the case of Penang based on the Selangor logistic regression coefficients showed the lowest accuracy (79%). Qualitatively, the cross
Berdaky, Mafalda Feliciano
2000-07-01
This work presents the operational part of the final process of the establishment of a radiotherapy service with a linear accelerator (6 MeV photon beams), including the acceptance tests, commissioning tests and the implementation of a quality control program through routine mechanical and radiation tests. All acceptance tests were satisfactory, showing results below the allowed limits of the manufacturer, the commissioning tests presented results within those of the international recommendations. The quality control program was performed during 34 months and showed an excellent stability of this accelerator. (author)
Tellado, Joseph
2014-01-01
The presentation contains a status of KSC ISS Logistics Operations. It basically presents current top level ISS Logistics tasks being conducted at KSC, current International Partner activities, hardware processing flow focussing on late Stow operations, list of KSC Logistics POC's, and a backup list of Logistics launch site services. This presentation is being given at the annual International Space Station (ISS) Multi-lateral Logistics Maintenance Control Panel meeting to be held in Turin, Italy during the week of May 13-16. The presentatiuon content doesn't contain any potential lessons learned.
Total Logistic Plant Solutions
Dusan Dorcak
2016-02-01
Full Text Available The Total Logistics Plant Solutions, plant logistics system - TLPS, based on the philosophy of advanced control processes enables complex coordination of business processes and flows and the management and scheduling of production in the appropriate production plans and planning periods. Main attributes of TLPS is to create a comprehensive, multi-level, enterprise logistics information system, with a certain degree of intelligence, which accepts the latest science and research results in the field of production technology and logistics. Logistic model of company understands as a system of mutually transforming flows of materials, energy, information, finance, which is realized by chain activities and operations
Wang, D Z; Wang, C; Shen, C F; Zhang, Y; Zhang, H; Song, G D; Xue, X D; Xu, Z L; Zhang, S; Jiang, G H
2017-05-10
We described the time trend of acute myocardial infarction (AMI) from 1999 to 2013 in Tianjin incidence rate with Cochran-Armitage trend (CAT) test and linear regression analysis, and the results were compared. Based on actual population, CAT test had much stronger statistical power than linear regression analysis for both overall incidence trend and age specific incidence trend (Cochran-Armitage trend P valuelinear regression P value). The statistical power of CAT test decreased, while the result of linear regression analysis remained the same when population size was reduced by 100 times and AMI incidence rate remained unchanged. The two statistical methods have their advantages and disadvantages. It is necessary to choose statistical method according the fitting degree of data, or comprehensively analyze the results of two methods.
Improving Healthcare Logistics Processes
Feibert, Diana Cordes
logistics processes in hospitals and aims to provide theoretically and empirically based evidence for improving these processes to both expand the knowledge base of healthcare logistics and provide a decision tool for hospital logistics managers to improve their processes. Case studies were conducted...... processes. Furthermore, a method for benchmarking healthcare logistics processes was developed. Finally, a theoretically and empirically founded framework was developed to support managers in making an informed decision on how to improve healthcare logistics processes. This study contributes to the limited...... literature concerned with the improvement of logistics processes in hospitals. Furthermore, the developed framework provides guidance for logistics managers in hospitals on how to improve their processes given the circumstances in which they operate....
Paulo José Guimarães Da-Silva
Full Text Available Abstract Introduction In this work, the effect of a dynamic visual stimulation (DS protocol was used to induce egomotion, the center of pressure (COP displacement response. Methods DS was developed concerning the scenario structure (chessboard-pattern floor and furniture and luminance. To move the scenario in a discrete forward (or backward direction, the furniture is expanded (or reduced and the black and white background is reversed during floor translation while the luminance is increased (or reduced by steps of 2 cd/m2. This protocol was evaluated using COP signals from 29 healthy volunteers: standing on a force platform observing the virtual scene (1.72 × 1.16 m projected 1 m ahead (visual incidence angle: θl = 81.4° and θv = 60.2°, which moves with constant velocity (2 m/s during 250 ms. A set of 100 DS was applied in random order, interspersed by a 10 s of static scene. Results The Tukey post-hoc test (p < 0.001 indicated egomotion in the same direction of DS. COP displacement increased over stimulation (8.4 ± 1.7 to 22.6 ±5.3 mm, as well as time to recover stability (4.1 ± 0.4 to 7.2 ± 0.6 s. The peak of egomotion during DSF occurred 200 ms after DSB (Wilcoxon, p = 0.002. Conclusion The dynamic configuration of this protocol establishes virtual flow effects of linear egomotion dependent on the direction of the dynamic visual stimulation. This finding indicates the potential application of the proposed virtual dynamic stimulation protocol to investigate the cortical visual evoked response in postural control studies.
Introduction to generalized linear models
Dobson, Annette J
2008-01-01
Introduction Background Scope Notation Distributions Related to the Normal Distribution Quadratic Forms Estimation Model Fitting Introduction Examples Some Principles of Statistical Modeling Notation and Coding for Explanatory Variables Exponential Family and Generalized Linear Models Introduction Exponential Family of Distributions Properties of Distributions in the Exponential Family Generalized Linear Models Examples Estimation Introduction Example: Failure Times for Pressure Vessels Maximum Likelihood Estimation Poisson Regression Example Inference Introduction Sampling Distribution for Score Statistics Taylor Series Approximations Sampling Distribution for MLEs Log-Likelihood Ratio Statistic Sampling Distribution for the Deviance Hypothesis Testing Normal Linear Models Introduction Basic Results Multiple Linear Regression Analysis of Variance Analysis of Covariance General Linear Models Binary Variables and Logistic Regression Probability Distributions ...
Stability Tests of Positive Fractional Continuous-time Linear Systems with Delays
Tadeusz Kaczorek
2013-06-01
Full Text Available Necessary and sufficient conditions for the asymptotic stability of positive fractional continuous-time linear systems with many delays are established. It is shown that: 1 the asymptotic stability of the positive fractional system is independent of their delays, 2 the checking of the asymptotic stability of the positive fractional systems with delays can be reduced to checking of the asymptotic stability of positive standard linear systems without delays.
1977-12-01
The M.C.H./M.E.N.T.3 document is concerned with sub-assemblies intended for measuring on a linear scale the neutron fluence rate or radiation dose rate when connected with nuclear detectors working in current. The symbols used are described. Some definitions and a bibliography are given. The main characteristics of direct current linear measurement sub-assemblies are then described together with corresponding test methods. This type of instrument indicates on a linear scale the level of a direct current applied to its input. The document reviews linear sub-assemblies for general purpose applications, difference amplifiers for monitoring, and averaging amplifiers. The document is intended for electronics manufacturers, designers, persons participating in acceptance trials and plant operators [fr
Logistics service management; differentiating the logistics service
Veeken, van der D.J.M.; Rutten, W.G.M.M.
1998-01-01
In this article a model is described, which enables differentiation of the logistics service that a company offers to its customers. Differentiating this service is essential for businesses with a large variation within their customer and/or products portfolio. The model consists of four phases:
Logistics Innovation Process Revisited
Gammelgaard, Britta; Su, Shong-Iee Ivan; Yang, Su-Lan
2011-01-01
Purpose – The purpose of this paper is to learn more about logistics innovation processes and their implications for the focal organization as well as the supply chain, especially suppliers. Design/methodology/approach – The empirical basis of the study is a longitudinal action research project...... that was triggered by the practical needs of new ways of handling material flows of a hospital. This approach made it possible to revisit theory on logistics innovation process. Findings – Apart from the tangible benefits reported to the case hospital, five findings can be extracted from this study: the logistics...... innovation process model may include not just customers but also suppliers; logistics innovation in buyer-supplier relations may serve as an alternative to outsourcing; logistics innovation processes are dynamic and may improve supplier partnerships; logistics innovations in the supply chain are as dependent...
LOGISTICS - EVOLUTION THROUGH INNOVATION
Petrache Alexandru Constantin
2015-07-01
Full Text Available The current economic conditions, the rapidity with which the exchange of information, resources and products in the market takes place makes the logistics seem appreciably less significant. However, the importance of logistics has been presented in the military field, through strategies that have led to wining of the great wars that mankind has seen, through the supply of troops with food or moving military equipment. The literature in the field of logistics has numerous works on this topic. But while most focuses on efficient ways of carrying out the component activities of logistics or the strategies of organizations with regard to logistics or its functions, research on dynamics of logistics is underdeveloped. To be able to propose new methods or strategies of logistic activities is necessary to understand the development of this concept, determinant factors and economic and social conditions that gave rise to such developments. Thus, after a presentation of the main landmarks of the historical development of logistics we highlight the importance of the innovation within an organization's value chain innovation, in particular, and how to conduct the business in general. Using generations of innovation identified in the literature, we determine the generation of logistics development, taking into account innovation and how to conduct business. In addition for a better highlight of the own vision over the logistics generations identified, we will present the graphical concept for each generation in part. Last but not least, for each generation identified we try to allocate the chronological landmarks featured in order to reinforce the importance played by innovation in the development of the logistics industry and to give future directions of research within this topic. The study took into account the information presented in articles, books and websites of the relevant specialty in logistics and innovation to be able to build and expose a
WAREOOUSE LOGISTICS MANAGEMENT
Drago Pupavac
2012-01-01
Warehouse Logistics Management involves the management of storage facilities and equipment, stock, employees and technology with the aim of efficient storage, accommodation, and distribution of goods and more importantly profitably. In conditions of economic crisis and lower inventory turns, logistics managers put emphasis on those measures as a function of storage logistics cost reductions that require minimal investment. Accordingly, the fundamental objective of this scientific paper is to ...
Mills, James W.; And Others
1973-01-01
The Study reported here tested an application of the Linear Programming Model at the Reading Clinic of Drew University. Results, while not conclusive, indicate that this approach yields greater gains in speed scores than a traditional approach for this population. (Author)
Jereb, Borut; Drašković, Mimo; Gorenak, Irena; Bauk, Sanja; Fošner, Maja; Rosi, Bojan; Pupavac, Drago; Topolšek, Darja; Dorokhov, Oleksandr; Kramar, Uroš; Ivanović, Željko; Sternad, Marjan; Knez, Matjaž; Mlaker Kač, Sonja; Malyaretz, Ludmila
2018-01-01
The scientific monograph titled Logistics and Management – selected topics is the result of a bilateral project, lasting from 2013 to 2015 and titled “Preparation of a joint scientific monograph in the field of logistics and management issued at the Faculty of Logistics in Celje and the Maritime Faculty of Kotor”. The project was managed by Professor Maja Fošner, PhD, from the Faculty of Logistics at the University of Maribor, and Professor Veselin Draskovic, PdD, from the Maritime Faculty of...
High gradient experiment by accelerator test facility for Japan Linear Collider
Takeda, Seishi; Akemoto, Mitsuo; Hayano, Hitoshi; Naito, Takashi; Matsumoto, Hiroshi
1991-01-01
For the e + e - linear colliders in TeV energy region such as the Japan Linear Collider (JLC), the accelerating gradient will be one of the important parameters affecting the over all design of main linacs. The gradient determines the accelerating structures, RF frequencies, peak power, AC power, total length and cost. High gradient experiment by using a traveling wave structure in S-band frequencies is presented. Discussions are given about the dependence of dark current and structure length. As one of the parameters indicating the quality of the structure, the multiplication factor η has been proposed
Zanxiang Nie
2017-01-01
Full Text Available Linear wave energy converters generate intrinsically intermittent power with variable frequency and amplitude. A composite energy storage system consisting of batteries and super capacitors has been developed and controlled by buck-boost converters. The purpose of the composite energy storage system is to handle the fluctuations and intermittent characteristics of the renewable source, and hence provide a steady output power. Linear wave energy converters working in conjunction with a system composed of various energy storage devices, is considered as a microsystem, which can function in a stand-alone or a grid connected mode. Simulation results have shown that by applying a boost H-bridge and a composite energy storage system more power could be extracted from linear wave energy converters. Simulation results have shown that the super capacitors charge and discharge often to handle the frequent power fluctuations, and the batteries charge and discharge slowly for handling the intermittent power of wave energy converters. Hardware systems have been constructed to control the linear wave energy converter and the composite energy storage system. The performance of the composite energy storage system has been verified in experiments by using electronics-based wave energy emulators.
On the Use of Rank Tests and Estimates in the Linear Model.
1982-06-01
models," Journal of the Royal Statistical Society , Series B, 42, 366-371. Neter, J. and Wasserman, W. (1974), Applied Linear Statistical Models...University Park, PA. Schuster, E. (1974), "On the rate of convergence of an estimate of a functional of a probability density," Scandinavian Acturial
Behavioral Operations in Logistics
J. de Vries (Jelle)
2016-01-01
markdownabstractIn the world of logistics, a considerable share of all work is automated and performed by machines or robots. An examination of the existing logistics research reflects this image, since a substantial share of the studies focus on automated processes, and perfectly predictable
Psaraftis, Harilaos N.
2016-01-01
By green maritime logistics we mean achieving an acceptable environmental performance of the maritime transport logistical supply chain while at the same time respecting traditional economic criteria. In this paper the environmental focus is on maritime emissions. Achieving such goal may involve ...
International Logistics Science Conference
Hompel, Michael; Meier, J
2014-01-01
The importance of logistics in all its variations is still increasing. New technologies emerge, new planning methods and algorithms are developed, only to face a market with a growing complexity and the need of weighting monetary costs against ecological impact. Mastering these challenges requires a scientific viewpoint on logistics, but always with applications in mind. This volume presents up-to-date logistics research in all its diversity and interconnectedness. It grew out of the “International Logistics Science Conference” (ILSC) held in Dortmund in September 2013, bringing together leading scientists and young academics from nine different countries. The conference was jointly organized by the “Efficiency Cluster Logistics” and the “Fraunhofer Institute for Material Flow and Logistics”. The Program Committee used a double blind review process to choose the 12 strongest contributions, which were then grouped in four areas: - Sustainability logistics, including electric mobility, smart inform...
SIMULATION OF LOGISTICS PROCESSES
Yu. Taranenko
2016-08-01
Full Text Available The article deals with the theoretical basis of the simulation. The study shows the simulation of logistic processes in industrial countries is an integral part of many economic projects aimed at the creation or improvement of logistics systems. The paper was used model Beer Game for management of logistics processes in the enterprise. The simulation model implements in AnyLogic package. AnyLogic product allows us to consider the logistics processes as an integrated system, which allows reaching better solutions. Logistics process management involves pooling the sales market, production and distribution to ensure the temporal level of customer service at the lowest cost overall. This made it possible to conduct experiments and to determine the optimal size of the warehouse at the lowest cost.
Choi, Ui-Min; Ma, Ke; Blaabjerg, Frede
2018-01-01
In this paper, the lifetime prediction of power device modules based on the linear damage accumulation is studied in conjunction with simple mission profiles of converters. Superimposed power cycling conditions, which are called simple mission profiles in this paper, are made based on a lifetime ...... prediction of IGBT modules under power converter applications.......In this paper, the lifetime prediction of power device modules based on the linear damage accumulation is studied in conjunction with simple mission profiles of converters. Superimposed power cycling conditions, which are called simple mission profiles in this paper, are made based on a lifetime...... model in respect to junction temperature swing duration. This model has been built based on 39 power cycling test results of 600-V 30-A three-phase-molded IGBT modules. Six tests are performed under three superimposed power cycling conditions using an advanced power cycling test setup. The experimental...
Logistics and logistics support in crisis management and citizen protection
HOLEJŠOVSKÝ, Jan
2010-01-01
ABSTRAKT LOGISTICS AND LOGISTICS SUPPORT IN CRISIS MANAGEMENT AND CITIZEN PROTECTION The graduation thesis on topic "Logistics and logistics support in crisis management and citizen protection" is divided into several chapters, which in summary are a material presenting information about logistics and logistics support in crisis management and citizen protection. This was one of the aims at this work. Chapters I., II., III., IV. describe logistics and logistics support, crisis management, cit...
Evaluating three proposals for testing independence in non linear spatial processes
López Hernández, Fernando Antonio; Mate Sánchez-Val, María Luz; Artal Tur, Andrés
2013-01-01
[ENG]This paper evaluates the behaviour of different families of tests when checking for spatial independence in the presence of nonlinearities. To reach this goal, we select three representative proposals. The usual parametric tests of I-Moran, the nonparametric proposal of Brett and Pinkse (1997), and the semiparametric Scan test. In order to study how they perform, we simulate different nonlinear spatial structures by Monte Carlo methods, hence conducting empirical tests on ...
Co-location synergies : specialized versus diverse logistics concentration areas
Heuvel, van den, F.P.; Langen, de, P.W.; Donselaar, van, K.H.; Fransoo, J.C.
2012-01-01
Purpose: The purpose of this paper is to contribute to the understanding of spatial concentration of logistics firms by empirically analyzing synergies through co-location and investigating whether co-location of logistics establishments in specialized logistics concentration areas results in benefits compared to co-location in diverse logistics concentration areas. Methodology: A survey among managers of 128 logistics establishments located in logistics concentration areas was used to test f...
Cempírek, Václav; Nachtigall, Petr; Široký, Jaromír
2016-12-01
This paper deals with security of logistic chains according to incorrect declaration of transported goods, fraudulent transport and forwarding companies and possible threats caused by political influences. The main goal of this paper is to highlight possible logistic costs increase due to these fraudulent threats. An analysis of technological processes will beis provided, and an increase of these transport times considering the possible threatswhich will beis evaluated economic costs-wise. In the conclusion, possible threat of companies'` efficiency in logistics due to the costs`, means of transport and increase in human resources` increase will beare pointed out.
Hosmer, David W; Sturdivant, Rodney X
2013-01-01
A new edition of the definitive guide to logistic regression modeling for health science and other applications This thoroughly expanded Third Edition provides an easily accessible introduction to the logistic regression (LR) model and highlights the power of this model by examining the relationship between a dichotomous outcome and a set of covariables. Applied Logistic Regression, Third Edition emphasizes applications in the health sciences and handpicks topics that best suit the use of modern statistical software. The book provides readers with state-of-
FEEDBACK AND LOGISTICS CONTROLLING
Mehesne Berek Szilvia
2015-07-01
Full Text Available The following things led to that the feedback, the supervision and improvement of the processes have become more pronounced: continuous rise in the importance of logistics; increase in complexity of its content; its activity becoming more complex. These activities are necessary for the optimum information supply. The intensification of market competition requires the corporations to possess exact and up-to-date information about their activities. Complexity of the logistics system presumes a parallel application of an effective feedback, supervision and management system simultaneously with the given logistics system. The indispensability of logistics is also proved by the fact that it can be found sporadically (in the form of logistics departments or in a complex way in case of each organization. The logistical approach means a huge support in the management since it contains the complexity, the handling as a unit in order to ensure a harmony of the different corporate departments and part activities. In addition to the professional application of a logistics system, there is an opportunity to coordinate the relations inside an organization as well as between the organizations and to handle them as a unit. The sine qua non of the success of logistical processes is a harmony of the devices applied. The controlling system is a device for feeding back the processes of a corporate system. By means of the checkpoints intercalated into the processes, the logistics controlling provides information for the leadership which contributes even more to the complex approach of logistics system. By dint of the logistics controlling, the monitoring and coordination of every logistical part activity become possible with the help of information supply ensured by the logistics controlling. The logistics controlling reviews, assesses and coordinates; these activities have an effect on the cost and income management. Its reason is to be searched in the built
Cantero, E D; Bravin, E; Sosa, A
2014-01-01
We performed experimental tests to characterize the mechanical accuracy of a linear actuator designed by the company AVS for the movement of the scanning slit of the HIE-ISOLDE short diagnostic boxes. The mechanism consists of a linear actuator composed of two guiding rods and a lead screw, with a full stroke of 135 mm. A specially designed blade was mounted on the actuator and the transverse positioning of the blade was monitored with a camera-based optical system while moving the actuator at speeds of up to 10 mm/s. The repeatability of the positioning of the blade after several cycles around predefined positions was also measured. The results of the measurements and a general inspection of the device show that the proposed solution fulfils the specifications. A full prototype of short diagnostic box for the HIE-ISOLDE project can now be built for testing.
Logistics and Inventory System -
Department of Transportation — The Logistics and Inventory System (LIS) is the agencys primary supply/support automation tool. The LIS encompasses everything from order entry by field specialists...
Chang, Yoon S.; Oh, Chang H.
Nowadays, environmental management becomes a critical business consideration for companies to survive from many regulations and tough business requirements. Most of world-leading companies are now aware that environment friendly technology and management are critical to the sustainable growth of the company. The environment market has seen continuous growth marking 532B in 2000, and 590B in 2004. This growth rate is expected to grow to 700B in 2010. It is not hard to see the environment-friendly efforts in almost all aspects of business operations. Such trends can be easily found in logistics area. Green logistics aims to make environmental friendly decisions throughout a product lifecycle. Therefore for the success of green logistics, it is critical to have real time tracking capability on the product throughout the product lifecycle and smart solution service architecture. In this chapter, we introduce an RFID based green logistics solution and service.
American Society for Testing and Materials. Philadelphia
1995-01-01
1.1 This test method covers the interferometric determination of linear thermal expansion of premelted glaze frits and fired ceramic whiteware materials at temperatures lower than 1000°C (1830°F). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
New robust statistical procedures for the polytomous logistic regression models.
Castilla, Elena; Ghosh, Abhik; Martin, Nirian; Pardo, Leandro
2018-05-17
This article derives a new family of estimators, namely the minimum density power divergence estimators, as a robust generalization of the maximum likelihood estimator for the polytomous logistic regression model. Based on these estimators, a family of Wald-type test statistics for linear hypotheses is introduced. Robustness properties of both the proposed estimators and the test statistics are theoretically studied through the classical influence function analysis. Appropriate real life examples are presented to justify the requirement of suitable robust statistical procedures in place of the likelihood based inference for the polytomous logistic regression model. The validity of the theoretical results established in the article are further confirmed empirically through suitable simulation studies. Finally, an approach for the data-driven selection of the robustness tuning parameter is proposed with empirical justifications. © 2018, The International Biometric Society.
Conference Logistics Management 2013
Haasis, Hans-Dietrich; Kopfer, Herbert; Kotzab, Herbert; Schönberger, Jörn
2015-01-01
This contributed volume contains the collected research papers presented at the Logistik-Management-Konferenz 2013 organized by the VHB Wissenschaftliche Kommission Logistik, held in Bremen 2013. The papers reflect the current state-of-the-art in logistics and supply chain management, focusing on environmental sustainability in logistics and supply chain network dynamics and control. The target audience primarily comprises research experts in the field as well as practitioners but the book may also be beneficial for graduate students.
Modal Identification of A Tested Steel Frame using Linear ARX Model Structure
Yavuz Kaya
2009-07-01
Full Text Available This study contains the identification of modal dynamic properties of a 3-story large-scale steel test frame structure through shaking table measurements. Shaking table test is carried out to estimate the modal properties of the test frame such as natural frequencies, damping ratios and mode shapes. Among many different model structures, ARX (Auto Recursive Exogenous model structure is used for modal identification of the frame structure system. The unknown parameters in the obtained ARX model structure are estimated by Least-Square method by minimizing the AIC criteria with the help of a program coded in advanced computing software MATLAB®. The adopted model structure is then tested out in time domain to verify the validity of the model with the selected model parameters. Then the modal characteristics of test frame and the story stiffness are estimated using the white noise shakings. An attempt is done to determine the change of modal characteristics and the story stiffness of test frame according to the velocity, which the test frame structure experienced during the shaking schedule and also during the input shaking of El Centro 1940 NS. Results shows that there is an increase in damping ratio and a decrease in both story stiffness and natural frequency for all modes when the damage forms at cementitious device and the test frame structure itself during the shaking schedule.
Research on the Logistics Supply Chain in Port Logistics Transportation
Wang Yan-liang
2013-01-01
The aim of this study is to improve and increase the logistics system effectiveness and to solve the problem of optimal movement of different flows. Logistics transport carrying the world on material resources transfer exchange important mission and economic development and our lives are closely linked, logistics chain logistics transport occupies an important position and in the e logistics chain in port logistics has play a decisive role. For many coastal countries port logistics is the eco...
Sousa, Carlos H.S.; Peixoto, Jose G.P., E-mail: chenrique@ird.gov.br [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ), RIo de Janeiro, RJ (Brazil)
2013-07-01
Activimeters determine the activity of radioactive samples and them are validated by performance tests. This research determined the expanded uncertainties associated to the linearity test. Were used three dose calibrators and three sources of {sup 99}Tc{sup m} for testing using recommended protocol by the IAEA, which considered the decay of radioactive samples. The expanded uncertainties evaluated were not correlated with each other and their analysis considered a rectangular probability distribution. The results are also presented in graphical form by the function of normalized activity measured in terms of conventional true value. (author)
McMonagle, Gerard
2006-01-01
The CERN CTF3 facility is being used to test and demonstrate key technical issues for the CLIC (Compact Linear Collider) study. Pulsed RF power sources are essential elements in this test facility. Klystrons at S-band (29998.55 GHz), in conjunction with pulse compression systems, are used to power the Drive Beam Accelerator (DBA) to achieve an electron beam energy of 150 MeV. The L-Band RF system, includes broadband Travelling Wave Tubes (TWTs) for beam bunching with 'phase coded' sub pulses ...
Czarski, Tomasz; Romaniuk, Ryszard S.; Pozniak, Krzysztof T.; Simrock, Stefan
2004-07-01
The cavity control system for the TESLA -- TeV-Energy Superconducting Linear Accelerator project is initially introduced in this paper. The FPGA -- Field Programmable Gate Array technology has been implemented for digital controller stabilizing cavity field gradient. The cavity SIMULINK model has been applied to test the hardware controller. The step operation method has been developed for testing the FPGA device coupled to the SIMULINK model of the analog real plant. The FPGA signal processing has been verified according to the required algorithm of the reference MATLAB controller. Some experimental results have been presented for different cavity operational conditions.
Testing the dual-route model of perceived gaze direction: Linear combination of eye and head cues.
Otsuka, Yumiko; Mareschal, Isabelle; Clifford, Colin W G
2016-06-01
We have recently proposed a dual-route model of the effect of head orientation on perceived gaze direction (Otsuka, Mareschal, Calder, & Clifford, 2014; Otsuka, Mareschal, & Clifford, 2015), which computes perceived gaze direction as a linear combination of eye orientation and head orientation. By parametrically manipulating eye orientation and head orientation, we tested the adequacy of a linear model to account for the effect of horizontal head orientation on perceived direction of gaze. Here, participants adjusted an on-screen pointer toward the perceived gaze direction in two image conditions: Normal condition and Wollaston condition. Images in the Normal condition included a change in the visible part of the eye along with the change in head orientation, while images in the Wollaston condition were manipulated to have identical eye regions across head orientations. Multiple regression analysis with explanatory variables of eye orientation and head orientation revealed that linear models account for most of the variance both in the Normal condition and in the Wollaston condition. Further, we found no evidence that the model with a nonlinear term explains significantly more variance. Thus, the current study supports the dual-route model that computes the perceived gaze direction as a linear combination of eye orientation and head orientation.
Nashine, B.K.; Rao, B.P.C.
2014-01-01
Highlights: • Derivation of applicable design equations. • Design of an annular induction pump based on these equations. • Testing of the designed pump in a sodium test facility. • Performance evaluation of the designed pump. - Abstract: Annular linear induction pumps (ALIPs) are used for pumping electrically conducting liquid metals. These pumps find wide application in fast reactors since the coolant in fast reactors is liquid sodium which a good conductor of electricity. The design of these pumps is usually done using equivalent circuit approach in combination with numerical simulation models. The equivalent circuit of ALIP is similar to that of an induction motor. This paper presents the derivation of equivalent circuit parameters using first principle approach. Sodium testing of designed ALIP using the equivalent circuit approach is also described and experimental results of the testing are presented. Comparison between experimental and analytical calculations has also been carried out. Some of the reasons for variation have also been listed in this paper
Free-piston Stirling engine/linear alternator 1000-hour endurance test
Rauch, J.; Dochat, G.
1985-01-01
The Free Piston Stirling Engine (FPSE) has the potential to be a long lived, highly reliable, power conversion device attractive for many product applications such as space, residential or remote site power. The purpose of endurance testing the FPSE was to demonstrate its potential for long life. The endurance program was directed at obtaining 1000 operational hours under various test conditions: low power, full stroke, duty cycle and stop/start. Critical performance parameters were measured to note any change and/or trend. Inspections were conducted to measure and compare critical seal/bearing clearances. The engine performed well throughout the program, completing more than 1100 hours. Hardware inspection, including the critical clearances, showed no significant change in hardware or clearance dimensions. The performance parameters did not exhibit any increasing or decreasing trends. The test program confirms the potential for long life FPSE applications.
PXIe-based LLRF architecture and versatile test bench for heavy ion linear acceleration
Jugo, I. Badillo J.; Portilla, J.; Feutchwanger, J.; Vicente, C. San; Etxebarria, V.
2014-01-01
This work describes the architecture of a digital LLRF system for heavy-ion acceleration developed under the specification of the projected future heavy-ion accelerator facility in Huelva, Spain. A prototype LLRF test bench operating at 80MHz in CW mode has been designed and built. The core LLRF control has been digitally implemented on a PXIe chassis, including an FPGA for digital signal processing and a real time controller. The test bench is completed with a good quality signal generator u...
Automated Testing Experience of the Linear Aerospike SR-71 Experiment (LASRE) Controller
Larson, Richard R.
1999-01-01
System controllers must be fail-safe, low cost, flexible to software changes, able to output health and status words, and permit rapid retest qualification. The system controller designed and tested for the aerospike engine program was an attempt to meet these requirements. This paper describes (1) the aerospike controller design, (2) the automated simulation testing techniques, and (3) the real time monitoring data visualization structure. Controller cost was minimized by design of a single-string system that used an off-the-shelf 486 central processing unit (CPU). A linked-list architecture, with states (nodes) defined in a user-friendly state table, accomplished software changes to the controller. Proven to be fail-safe, this system reported the abort cause and automatically reverted to a safe condition for any first failure. A real time simulation and test system automated the software checkout and retest requirements. A program requirement to decode all abort causes in real time during all ground and flight tests assured the safety of flight decisions and the proper execution of mission rules. The design also included health and status words, and provided a real time analysis interpretation for all health and status data.
Hompel, Michael; Klumpp, Matthias
2013-01-01
The „EffizienzCluster LogistikRuhr“ was a winner in the Leading Edge Science Cluster competition run by the German federal Ministry of Education and Research. The mission and aim of the „EffizienzCluster LogistikRuhr“ is to facilitate tomorrow’s individuality – in the sense of individual goods supply, mobility, and production – using 75 percent of today’s resources. Efficiency – both in economical and ecological terms – is enabled by state-of-the-art and innovative logistical solutions including transportation, production and intralogistics. These proceedings “Efficiency and Logistics” give first answers from 27 research projects as an insight into the current state of research of Europe’s leading research and development cluster in logistics and as a contribution to the discussion on how logistics as a science can help to cope with foreseeable resource shortage and sustainability as global challenges.
Logistics innovation development
Pedrosa, Alex; Blazevic, Vera; Jasmand, Claudia
2014-01-01
to investigate the role of boundary-spanning employees in deepening and broadening customer knowledge while developing logistics service innovations. Findings The results show that boundary-spanning employees’ engage sequentially in deepening and broadening customer knowledge throughout the logistics innovation...... development process. In particular it shows that deepening customer knowledge tends to occur in one-to-one interactions. When boundary-spanning employees engage in broadening customer knowledge, they develop a rich understanding of current customer. Research limitations/implications (if applicable) In general......Purpose This paper aims to investigate the microfoundations—boundary-spanning employees activities and behaviors—of deepening and broadening customer knowledge during logistics innovation development. Design/methodology/approach A multiple case study approach (six case studies) was adopted...
Psaraftis, Harilaos N.
2014-01-01
Typical problems in maritime logistics include, among others, optimal ship speed, ship routing and scheduling, fleet deployment, fleet size and mix, weather routing, intermodal network design, modal split, transshipment, queuing at ports, terminal management, berth allocation, and total supply...... chain management. The traditional analysis of these problems has been in terms of cost- benefit and other optimization criteria from the point of view of the logistics provider, carrier, shipper, or other end-user. Such traditional analysis by and large either ignores environmental issues, or considers...... them of secondary importance. Green maritime logistics tries to bring the environmental dimension into the problem, and specifically the dimension of emissions reduction, by analyzing various trade-offs and exploring ‘win-win’ solutions. This talk takes a look at the trade-offs that are at stake...
Genier, C.; Capper, S.
1988-01-01
The size of the LEP project, coupled with the tight construction schedules, calls for organized planning, logistics, monitoring and control. This is being carried out at present using tools such as ORACLE the Relational Database Management System, running on a VAX cluster for data storage and transfer, micro-computers for on-site follow-up, and PC's running Professional ORACLE, DOS and XENIX linked to a communications network to receive data feedback concerning transport and handling means. Following over 2 years of installations, this paper presents the methods used for the logistics of installation and their results
Rise of humanitarian logistics
Maspero, EL
2008-07-01
Full Text Available but was described as fairly routine for a company of Walmart’s size with 117 distribution centres spread around the country. The nonchalant response by Rollin Ford, (Walmart’s executive vice president of logistics and supply chain) says it all, “that’s what we do...%20and%20challenges%22 [3] Boorstin, J. 2005. New lessons to learn. Fortune. 3 October. [4] Davidson, A.L. 2006. Key Performance Indicators in Humanitarian Logistics. MLOG Thesis, 2006. Viewed 24 October 2006. [5] http...
Design and Factory Test of the E /E- Frascati Linear Accelerator for DAFNE
Anamkath, H.; Lyons, S.; Nett, D.; Treas, P.; Whitham, K.; Zante, T.; /Titan Beta, Dublin; Miller, R.; /Titan Beta, Dublin /SLAC; Boni, R.; Hsieh, H.; Sannibale, F.; Vescovi, M.; Vignola, G.; /Frascati
2011-11-28
The electron-positron accelerator for the DAFNE project has been built and is in test at Titan Beta in Dublin, CA. This S-Band RF linac system utilizes four 45 MW sledded klystrons and 16-3 m accelerating structures to achieve the required performance. It delivers a 4 ampere electron beam to the positron converter and accelerates the resulting positrons to 550 MeV. The converter design uses a 4.3T pulsed tapered flux compressor along with a pseudo-adiabatic tapered field to a 5 KG solenoid over the first two positron accelerating sections. Quadrupole focusing is used after 100 MeV. The system performance is given in Table 1. This paper briefly describes the design and development of the various subassemblies in this system and gives the initial factory test data.
Ayşenur DOĞRU; Cemile SOLAK FIŞKIN
2016-01-01
Increasing concerns related to environmental side effects of the logistics services and competition between the logistics service providers are two pressuring factors on logistics service providers. This study seeks to explore the relation between green logistics tendency and logistic performance from the perspective of logistics service providers. In order to reach this aim, two logistics service providers are investigated by comparative case study method. Findings showed the effects of g...
Vacuum seals design and testing for a linear accelerator of the National Spallation Neutron Source
Chen, Z.; Gautier, C.; Hemez, F.; Bultman, N.K.
2000-01-01
Vacuum seals are very important to ensure that the Spallation Neutron Source (SNS) Linac has an optimum vacuum system. The vacuum joints between flanges must have reliable seals to minimize the leak rate and meet vacuum and electrical requirements. In addition, it is desirable to simplify the installation and thereby also simplify the maintenance required. This report summarizes an investigation of the metal vacuum seals that include the metal C-seal, Energized Spring seal, Helcoflex Copper Delta seal, Aluminum Delta seal, delta seal with limiting ring, and the prototype of the copper diamond seals. The report also contains the material certifications, design, finite element analysis, and testing for all of these seals. It is a valuable reference for any vacuum system design. To evaluate the suitability of several types of metal seals for use in the SNS Linac and to determine the torque applied on the bolts, a series of vacuum leak rate tests on the metal seals have been completed at Los Alamos Laboratory. A copper plated flange, using the same type of delta seal that was used for testing with the stainless steel flange, has also been studied and tested. A vacuum seal is desired that requires significantly less loading than a standard ConFlat flange with a copper gasket for the coupling cavity assembly. To save the intersegment space the authors use thinner flanges in the design. The leak rate of the thin ConFlat flange with a copper gasket is a baseline for the vacuum test on all seals and thin flanges. A finite element analysis of a long coupling cavity flange with a copper delta seal has been performed in order to confirm the design of the long coupling cavity flange and the welded area of a cavity body with the flange. This analysis is also necessary to predict a potential deformation of the cavity under the combined force of atmospheric pressure and the seating load of the seal. Modeling of this assembly has been achieved using both HKS/Abaqus and COSMOS
Vacuum seals design and testing for a linear accelerator of the National Spallation Neutron Source
Z. Chen; C. Gautier; F. Hemez; N. K. Bultman
2000-02-01
Vacuum seals are very important to ensure that the Spallation Neutron Source (SNS) Linac has an optimum vacuum system. The vacuum joints between flanges must have reliable seals to minimize the leak rate and meet vacuum and electrical requirements. In addition, it is desirable to simplify the installation and thereby also simplify the maintenance required. This report summarizes an investigation of the metal vacuum seals that include the metal C-seal, Energized Spring seal, Helcoflex Copper Delta seal, Aluminum Delta seal, delta seal with limiting ring, and the prototype of the copper diamond seals. The report also contains the material certifications, design, finite element analysis, and testing for all of these seals. It is a valuable reference for any vacuum system design. To evaluate the suitability of several types of metal seals for use in the SNS Linac and to determine the torque applied on the bolts, a series of vacuum leak rate tests on the metal seals have been completed at Los Alamos Laboratory. A copper plated flange, using the same type of delta seal that was used for testing with the stainless steel flange, has also been studied and tested. A vacuum seal is desired that requires significantly less loading than a standard ConFlat flange with a copper gasket for the coupling cavity assembly. To save the intersegment space the authors use thinner flanges in the design. The leak rate of the thin ConFlat flange with a copper gasket is a baseline for the vacuum test on all seals and thin flanges. A finite element analysis of a long coupling cavity flange with a copper delta seal has been performed in order to confirm the design of the long coupling cavity flange and the welded area of a cavity body with the flange. This analysis is also necessary to predict a potential deformation of the cavity under the combined force of atmospheric pressure and the seating load of the seal. Modeling of this assembly has been achieved using both HKS/Abaqus and COSMOS
Logistics Reduction: RFID Enabled Autonomous Logistics Management (REALM)
National Aeronautics and Space Administration — The Advanced Exploration Systems (AES) Logistics Reduction (LR) project Radio-frequency identification (RFID) Enabled Autonomous Logistics Management (REALM) task...
Tests of a numerical algorithm for the linear instability study of flows on a sphere
Perez Garcia, Ismael; Skiba, Yuri N [Univerisidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)
2001-04-01
A numerical algorithm for the normal mode instability of a steady nondivergent flow on a rotating sphere is developed. The algorithm accuracy is tested with zonal solutions of the nonlinear barotropic vorticity equation (Legendre polynomials, zonal Rossby-Harwitz waves and monopole modons). [Spanish] Ha sido desarrollado un algoritmo numerico para estudiar la inestabilidad lineal de un flujo estacionario no divergente en una esfera en rotacion. La precision del algoritmo se prueba con soluciones zonales de la ecuacion no lineal de vorticidad barotropica (polinomios de Legendre, ondas zonales Rossby-Harwitz y modones monopolares).
Background Acoustics Levels in the 9x15 Wind Tunnel and Linear Array Testing
Stephens, David
2011-01-01
The background noise level in the 9x15 foot wind tunnel at NASA Glenn has been documented, and the results compare favorably with historical measurements. A study of recessed microphone mounting techniques was also conducted, and a recessed cavity with a micronic wire mesh screen reduces hydrodynamic noise by around 10 dB. A three-microphone signal processing technique can provide additional benefit, rejecting up to 15 dB of noise contamination at some frequencies. The screen and cavity system offers considerable benefit to test efficiency, although there are additional calibration requirements.
Bayesian logistic regression analysis
Van Erp, H.R.N.; Van Gelder, P.H.A.J.M.
2012-01-01
In this paper we present a Bayesian logistic regression analysis. It is found that if one wishes to derive the posterior distribution of the probability of some event, then, together with the traditional Bayes Theorem and the integrating out of nuissance parameters, the Jacobian transformation is an
Wells, M.
1996-01-01
The article relates to offshore cost reduction in the UK and Norwegian sectors. Improvements within logistics and industrial co-operation are discussed being inspired by the joint government and industry NORSOK programme and the similar UK CRINE programme. Examples on cost reduction in various projects are given. 1 fig
and Multinomial Logistic Regression
This work presented the results of an experimental comparison of two models: Multinomial Logistic Regression (MLR) and Artificial Neural Network (ANN) for classifying students based on their academic performance. The predictive accuracy for each model was measured by their average Classification Correct Rate (CCR).
2007-01-01
...), is intended as a simple guide to logistics in NATO. It does not attempt to examine current issues or provide answers to the problems that logisticians will face, but it rather aims at introducing them to some of the basic principles, policies...
Logistics innovation development
Pedrosa, Alex; Blazevic, Vera; Jasmand, Claudia
2015-01-01
Purpose – The purpose of this paper is to investigate the microfoundations of customer knowledge acquisition during logistics innovation development. Specifically, the authors explore the activities and behaviors of employees with customer contact (i.e. boundary-spanning employees (BSEs)) to deepen...
Logistics Services Communication
2006-01-01
Members of the personnel are invited to take note that only parcels corresponding to official orders or contracts will be handled at CERN. Individuals are not authorisedto have private merchandise delivered to them at CERN and private deliveries will not be accepted by the Goods Reception services. Thank you for your understanding. Logistics Services - FI Department - 79947
Logistics Services Communication
2006-01-01
Members of the personnel are invited to take note that only parcels corresponding to official orders or contracts will be handled at CERN. Individuals are not authorised to have private merchandise delivered to them at CERN and private deliveries will not be accepted by the Goods Reception services. Thank you for your understanding. Logistics Services - FI Department - 79947
Logistics, Management and Efficiency
Mircea UDRESCU; Sandu CUTURELA
2014-01-01
The problem related to the efficiency of the management for organization is general being the concern off all managers. In the present essay we consider that the efficacy of the organization begins from the structural systemization of the organizational management into general management, management of logistics and management of production which demands a new managerial process, more competitive based on economic efficiency.
Marullo, F.
2015-01-01
The term "logistics" derives from the Greek logizomai standing for the art of reckoning, organising, planning. Through time it achieved a strict military connotation, dealing with the composition, lodging and movements of troops, the arrangement of provisions in hostile territories, the
Tiunov, V. V.
2018-02-01
The report provides results of the research related to the tubular linear induction motors’ application. The motors’ design features, a calculation model, a description of test specimens for mining and electric power industry are introduced. The most attention is given to the single-phase motors for high voltage switches drives with the usage of inexpensive standard single-phase transformers for motors’ power supply. The method of the motor’s parameters determination, when the motor is being fed from the transformer, working in the overload mode, was described, and the results of it practical usage were good enough for the engineering practice.
Non-linear advanced control of the LHC inner triplet heat exchanger test unit
Vinuela, E. Blanco; Cubillos, J. Casas; Prada Moraga, C. de; Cristea, S.
2002-01-01
The future Large Hadron Collider (LHC) at CERN will include eight interaction region final focus magnet systems, the so-called 'Inner Triplet', one on each side of the four beam collision points. The Inner Triplets will be cooled in a static bath of pressurized He II nominally at 1.9 K. This temperature is a control parameter and has very severe constraints in order to avoid the transition from the superconducting to normal resistive state. The main difference in these special zones with respect to a regular LHC cell is higher dynamic heat load unevenly distributed which modifies largely the process characteristics and hence the controller performance. Several control strategies have already been tested at CERN in a pilot plant (LHC String Test) which reproduced a LHC half-cell. In order to validate a common control structure along the whole LHC ring, a Nonlinear Model Predictive Control (NMPC) has been developed and implemented in the Inner Triplet Heat Exchanger Unit (IT-HXTU) at CERN. Automation of the Inner Triplet setup and the advanced control techniques deployed based on the Model Based Predictive Control (MBPC) principle are presented
Linear Array Ultrasonic Test Results from Alkali-Silica Reaction (ASR) Specimens
Clayton, Dwight A [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Khazanovich, Dr. Lev [Univ. of Minnesota, Minneapolis, MN (United States); Salles, Lucio [Univ. of Minnesota, Minneapolis, MN (United States)
2016-04-01
The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years. Since many important safety structures in an NPP are constructed of concrete, inspection techniques must be developed and tested to evaluate the internal condition. In-service containment structures generally do not allow for the destructive measures necessary to validate the accuracy of these inspection techniques. This creates a need for comparative testing of the various nondestructive evaluation (NDE) measurement techniques on concrete specimens with known material properties, voids, internal microstructure flaws, and reinforcement locations.This report presents results of the ultrasound evaluation of four concrete slabs with varying levels of ASR damage present. This included an investigation of the experimental results, as well as a supplemental simulation considering the effect of ASR damage by elasto-dynamic wave propagation using a finite integration technique method. It was found that the Hilbert Transform Indicator (HTI), developed for quantification of freeze/thaw damage in concrete structures, could also be successfully utilized for quantification of ASR damage. internal microstructure flaws, and reinforcement locations.
Single-Event Transient Testing of Low Dropout PNP Series Linear Voltage Regulators
Adell, Philippe; Allen, Gregory
2013-01-01
As demand for high-speed, on-board, digital-processing integrated circuits on spacecraft increases (field-programmable gate arrays and digital signal processors in particular), the need for the next generation point-of-load (POL) regulator becomes a prominent design issue. Shrinking process nodes have resulted in core rails dropping to values close to 1.0 V, drastically reducing margin to standard switching converters or regulators that power digital ICs. The goal of this task is to perform SET characterization of several commercial POL converters, and provide a discussion of the impact of these results to state-of-the-art digital processing IC through laser and heavy ion testing
Development of the rf linear accelerator test bed for heavy-ion fusion
Watson, J.M.
1981-01-01
The amount of absorbed energy required by high gain deuterium-tritium targets for inertial confinement fusion reactors is now projected to be greater than 1 Megajoule. It has become apparent that a heavy ion fusion driver is the preferred choice in this scenario. To demonstrate this accelerator-based option, the national program has established two test beds: one at Argonne for the rf linac/storage ring approach, and one at Lawrence Berkeley Laboratory developing an induction linac. The Argonne Beam Development Facility (BDF) would consist of a 40 mA rf linac for Xe + 8 , a storage ring, and a 10 GeV synchrotron. The design and status of the BDF is described as well as future program options to demonstrate as many solutions as possible of the issues involved in this approach
Assessing the discriminating power of item and test scores in the linear factor-analysis model
Pere J. Ferrando
2012-01-01
Full Text Available Las propuestas rigurosas y basadas en un modelo psicométrico para estudiar el impreciso concepto de "capacidad discriminativa" son escasas y generalmente limitadas a los modelos no-lineales para items binarios. En este artículo se propone un marco general para evaluar la capacidad discriminativa de las puntuaciones en ítems y tests que son calibrados mediante el modelo de un factor común. La propuesta se organiza en torno a tres criterios: (a tipo de puntuación, (b rango de discriminación y (c aspecto específico que se evalúa. Dentro del marco propuesto: (a se discuten las relaciones entre 16 medidas, de las cuales 6 parecen ser nuevas, y (b se estudian las relaciones entre ellas. La utilidad de la propuesta en las aplicaciones psicométricas que usan el modelo factorial se ilustra mediante un ejemplo empírico.
Space Station fluid management logistics
Dominick, Sam M.
1990-01-01
Viewgraphs and discussion on space station fluid management logistics are presented. Topics covered include: fluid management logistics - issues for Space Station Freedom evolution; current fluid logistics approach; evolution of Space Station Freedom fluid resupply; launch vehicle evolution; ELV logistics system approach; logistics carrier configuration; expendable fluid/propellant carrier description; fluid carrier design concept; logistics carrier orbital operations; carrier operations at space station; summary/status of orbital fluid transfer techniques; Soviet progress tanker system; and Soviet propellant resupply system observations.
Battlespace Logistics Readiness and Sustainment Research
Jacobs, John T
2005-01-01
... and evaluate logistics technologies. Within the scope of this program specific research tasks could be focused on feasibility studies, cost benefit analyses, modeling and simulation data and algorithms, front-end analyses, field test...
Olive, David J
2017-01-01
This text covers both multiple linear regression and some experimental design models. The text uses the response plot to visualize the model and to detect outliers, does not assume that the error distribution has a known parametric distribution, develops prediction intervals that work when the error distribution is unknown, suggests bootstrap hypothesis tests that may be useful for inference after variable selection, and develops prediction regions and large sample theory for the multivariate linear regression model that has m response variables. A relationship between multivariate prediction regions and confidence regions provides a simple way to bootstrap confidence regions. These confidence regions often provide a practical method for testing hypotheses. There is also a chapter on generalized linear models and generalized additive models. There are many R functions to produce response and residual plots, to simulate prediction intervals and hypothesis tests, to detect outliers, and to choose response trans...
Linear stability of toroidal Alfvén eigenmodes in the Chinese Fusion Engineering Test Reactor
Yang, Wenjun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230026 (China); Li, Guoqiang, E-mail: ligq@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Hu, Youjun; Gao, Xiang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)
2017-01-15
The Chinese Fusion Engineering Test Reactor (CFETR) is under design. It aims to fill the gaps between ITER and DEMO. In the reactor, the deuterium-tritium fusion reaction and the auxiliary heating will generate a lot of energetic particles. It is possible that these energetic particles will drive toroidal Alfvén eigenmode (TAE) instabilities under the conditions of CFETR plasma parameters. These instabilities can result in energetic particles redistribution or loss, so it’s vital to study TAE instabilities in CFETR. The aim of this paper is to study the possibility of reducing TAE instabilities by changing safety factor profiles in CFETR. NOVA and NOVA-K codes are used to study TAE stability. The equilibria are constructed using the CORSICA code. Safety factor profiles are selected as the three typical profiles of ITER scenarios. For the three different safety factor profiles, we use NOVA to scan and calculate their continuum spectrum and eigenmode structures, then use NOVA-K to calculate the different damping and driving mechanisms for different toroidal mode numbers. The numerical calculations show that if the safety factor profiles are chosen appropriately, then all the TAEs can be stable. Thus, it’s possible to reduce the TAE instabilities by changing safety factor profiles in CFETR. We also scan the temperature and density profiles to see their effects on the TAE instabilities. It shows that the TAE instabilities keep unchanged for a wide range of profiles.
McMonagle, Gerard
2006-01-01
The CERN CTF3 facility is being used to test and demonstrate key technical issues for the CLIC (Compact Linear Collider) study. Pulsed RF power sources are essential elements in this test facility. Klystrons at S-band (29998.55 GHz), in conjunction with pulse compression systems, are used to power the Drive Beam Accelerator (DBA) to achieve an electron beam energy of 150 MeV. The L-Band RF system, includes broadband Travelling Wave Tubes (TWTs) for beam bunching with 'phase coded' sub pulses in the injector and a narrow band high power L-Band klystron powering the transverse 1.5GHz RF deflector in the Delay Loop immediately after the DBA. This paper describes these different systems and discusses their operational performance.
McMonagle, Gerard
2006-01-01
The CERN CTF3 facility is being used to test and demonstrate key technical issues for the CLIC (Compact Linear Collider) study. Pulsed RF power sources are essential elements in this test facility. Klystrons at S-band (29998.55 GHz), in conjunction with pulse compression systems, are used to power the Drive Beam Accelerator (DBA) to achieve an electron beam energy of 150 MeV. The L-Band RF system, includes broadband Travelling Wave Tubes (TWTs) for beam bunching with 'phase coded' sub pulses in the injector and a narrow band high power L-Band klystron powering the transverse 1.5 GHz RF deflector in the Delay Loop immediately after the DBA. This paper describes these different systems and discusses their operational performance.
Siddiqi, Ariba; Arjunan, Sridhar P; Kumar, Dinesh K
2016-08-01
Age-associated changes in the surface electromyogram (sEMG) of Tibialis Anterior (TA) muscle can be attributable to neuromuscular alterations that precede strength loss. We have used our sEMG model of the Tibialis Anterior to interpret the age-related changes and compared with the experimental sEMG. Eighteen young (20-30 years) and 18 older (60-85 years) performed isometric dorsiflexion at 6 different percentage levels of maximum voluntary contractions (MVC), and their sEMG from the TA muscle was recorded. Six different age-related changes in the neuromuscular system were simulated using the sEMG model at the same MVCs as the experiment. The maximal power of the spectrum, Gaussianity and Linearity Test Statistics were computed from the simulated and experimental sEMG. A correlation analysis at α=0.05 was performed between the simulated and experimental age-related change in the sEMG features. The results show the loss in motor units was distinguished by the Gaussianity and Linearity test statistics; while the maximal power of the PSD distinguished between the muscular factors. The simulated condition of 40% loss of motor units with halved the number of fast fibers best correlated with the age-related change observed in the experimental sEMG higher order statistical features. The simulated aging condition found by this study corresponds with the moderate motor unit remodelling and negligible strength loss reported in literature for the cohorts aged 60-70 years.
Waste acceptance and logistics
Carlson, James H.
1992-01-01
There are three major components which are normally highlighted when the Civilian Radioactive Waste Management Program is discussed - the repository, the monitored retrievable storage facility, and the transportation system. These are clearly the major physical system elements and they receive the greatest external attention. However, there will not be a successful, operative waste management system without fully operational waste acceptance plans and logistics arrangements. This paper will discuss the importance of developing, on a parallel basis to the normally considered waste management system elements, the waste acceptance and logistics arrangements to enable the timely transfer of spent nuclear fuel from more than one hundred and twenty waste generators to the Federal government. The paper will also describe the specific activities the Program has underway to make the necessary arrangements. (author)
Humanitarian logistics and sustainability
Leeuw, Sander; Regattieri, Alberto; Souza, Robert
2015-01-01
This contributed volume combines conceptual and strategic research articles dealing with the "why" and "to what end" of sustainable operations in humanitarian logistics, as well as operational research contributions regarding the "how" from the United Nations as well as from researchers and organizations from different countries (Germany, Australia, Singapore, Italy, Denmark, Jordan). The target audience primarily comprises research experts, decision makers and practitioners in the field, but the book may also be beneficial for graduate students.
Knowledge Enabled Logistics (KEL)
2010-09-01
any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN...decentralization of work, globalization, telecommuting , emphasis on constant learning, and greater use of teams within the workplace. While these...visible within military Command and Control (C2) operations. The focus of the current report is on C2 within a logistics domain. 2.1
Jaeaeskelaeinen, A.
1998-01-01
Finland's oil, chemicals, and energy company, Neste, has achieved an enviable standard of logistics serving the markets around the Baltic Rim. Neste's safe and efficient transportation services are handled by its own fleet of tankers, time-chartered vessels, contract road tankers, and rail. Neste's terminals play an important part in the company's logistics network. The company operates four terminals of its own in Finland, and works with other oil companies at three of their terminals. Neste's own terminals are located at the company's refineries at Porvoo and Naantali, and at Kokkola and Kemi on the Gulf of Bothnia. Outside Finland the completion of a new terminal at Riga in Latvia, to enhance the logistics services provided to Neste's network of service stations and direct sales customers in the Baltic countries. This joins a terminal at Muuga near Tallinn in Estonia, which has been operational for some five years. Construction work began on a terminal in St. Petersburg in December 1997 to serve customers in the St. Petersburg and Vyborg areas. Completion is scheduled for autumn 1999
SU-E-T-354: Efficient and Enhanced QA Testing of Linear Accelerators Using a Real-Time Beam Monitor
Jung, J; Farrokhkish, M; Norrlinger, B; Wang, Y [Princess Margaret Cancer Centre, Toronto, Ontario (Canada); Heaton, R; Jaffray, D; Islam, M [Princess Margaret Cancer Centre, Toronto, Ontario (Canada); University of Toronto, Toronto, Ontario (Canada)
2015-06-15
Purpose: To investigate the feasibility of performing routine QA tests of linear accelerators (Linac) using the Integral Quality Monitoring (IQM) system. The system, consisting of a 1-D sensitivity gradient large area ion-chamber mounted at the collimator, allows automatic collection and analysis of beam data. Methods: The IQM was investigated to perform several QA constancy tests, similar to those recommended by AAPM TG142, of a Linac including: beam output, MLC calibration, beam symmetry, relative dose factor (RDF), dose linearity, output as a function of gantry angle and dose rate. All measurements by the IQM system accompanied a reference measurement using a conventional dosimetry system and were performed on an Elekta Infinity Linac with Agility MLC. The MLC calibration check is done using a Picket-Fence type 2×10cm{sup 2} field positioned at different off-axis locations along the chamber gradient. Beam symmetry constancy values are established by signals from an 4×4cm{sup 2} aperture located at various off-axis positions; the sensitivity of the test was determined by the changes in the signals in response to a tilt in the beam. The data for various square field sizes were used to develop a functional relationship with RDF. Results: The IQM tracked the beam output well within 1% of the reference ion-chamber readings. The Picket-Fence type field test detected a 1mm shift error of one MLC bank. The system was able to detect 2.5% or greater beam asymmetry. The IQM results for all other QA tests were found to agree with the reference values to within 0.5%. Conclusion: It was demonstrated that the IQM system can effectively monitor the Linac performance parameters for the purpose of routine QA constancy tests. With minimum user interactions a comprehensive set of tests can be performed efficiently, allowing frequent monitoring of the Linac. The presenting author’s salary is funded by the manufacturer of the QA device. All the other authors have financial
SU-E-T-354: Efficient and Enhanced QA Testing of Linear Accelerators Using a Real-Time Beam Monitor
Jung, J; Farrokhkish, M; Norrlinger, B; Wang, Y; Heaton, R; Jaffray, D; Islam, M
2015-01-01
Purpose: To investigate the feasibility of performing routine QA tests of linear accelerators (Linac) using the Integral Quality Monitoring (IQM) system. The system, consisting of a 1-D sensitivity gradient large area ion-chamber mounted at the collimator, allows automatic collection and analysis of beam data. Methods: The IQM was investigated to perform several QA constancy tests, similar to those recommended by AAPM TG142, of a Linac including: beam output, MLC calibration, beam symmetry, relative dose factor (RDF), dose linearity, output as a function of gantry angle and dose rate. All measurements by the IQM system accompanied a reference measurement using a conventional dosimetry system and were performed on an Elekta Infinity Linac with Agility MLC. The MLC calibration check is done using a Picket-Fence type 2×10cm 2 field positioned at different off-axis locations along the chamber gradient. Beam symmetry constancy values are established by signals from an 4×4cm 2 aperture located at various off-axis positions; the sensitivity of the test was determined by the changes in the signals in response to a tilt in the beam. The data for various square field sizes were used to develop a functional relationship with RDF. Results: The IQM tracked the beam output well within 1% of the reference ion-chamber readings. The Picket-Fence type field test detected a 1mm shift error of one MLC bank. The system was able to detect 2.5% or greater beam asymmetry. The IQM results for all other QA tests were found to agree with the reference values to within 0.5%. Conclusion: It was demonstrated that the IQM system can effectively monitor the Linac performance parameters for the purpose of routine QA constancy tests. With minimum user interactions a comprehensive set of tests can be performed efficiently, allowing frequent monitoring of the Linac. The presenting author’s salary is funded by the manufacturer of the QA device. All the other authors have financial interests with
Logistic innovations in transport
Mirosław Antonowicz
2014-03-01
Full Text Available Introduction: The article discusses the issue of logistic innovations in transport. The essentials of logistic innovations in transport together with some examples of specific innovations are presented. The role of the client's needs in transport innovations is indicated. The most vital postulates affecting the innovativeness of shipping companies and derived from the author's experience as well as scholarly publications, are time, safety, reliability as well as comprehensiveness of service offer. Following the analysis of the issue, and on the grounds of Kaizen's and Lean's method, the concept of continuous innovations is suggested as very useful for the development of transport. The potential of clusters as the source of logistic innovations in transport is emphasised. Methods: The discussion of the issue was preceded by the author's analysis of written sources on innovativeness, the evaluation of ratings of innovativeness as well as the analysis of rewarded innovative solutions in transport subsequent to the businesses participation in the programme of innovative solutions in transport. The role of innovation practical business operations is argued following the analysis of some strategic documents such as: 2011 White Paper and the Strategy for the Development of Transport by 2020 adopted by the Polish government in 2013. Aim: The aim of the article is to present the role and significance of the issue of logistic innovations in transport and to cite instances of practical solutions implemented by shipping companies, the solutions which resulted in measurable effects. Following the author's observation of the instances of innovative solutions as well as his analysis of the ratings of innovativeness, the article aims to present the conclusions as for the specific kinds of activities which are indispensable to foster innovativeness in transport. Conclusions: The conclusions derived from the author's analyses and observations show that logistic
Cooperation between partners in logistics outsourcing
Andreja KRIŽMAN
2009-01-01
Full Text Available The purpose of this article is to present the research results from a study of impact of cooperation between logistics service providers (LSP and their customers on logistics outsourcing performance conducted in the Slovenian market. On the basis of the existing literature and some new argumentations, derived from in-depth interviews with logistics experts of providers and customers, the measurement and structural models were empirically analyzed. Existing measurement scales for the constructs of cooperation, and outsourcing performance were slightly modified for this analysis. Their purification and measurement for validity and reliability were performed. Multivariate statistical methods (EFA, CFA and SEM - Partial Least Squares were utilized and hypotheses were tested. Cooperation between partners has a significant impact on the relationship and reduces problems in logistics performance. Cooperation in the model explain 58.5% of the variance of goal achievement and 36.6% of the variance of goal exceedance logistics of outsourcing performance.
Clement, Simon
2014-01-01
The present study is in the scope of pressurized water reactors (PWR) core response to earthquakes. The goal of this thesis is to measure the coupling between fuel assemblies caused an axial water flow. The design, production and installation a new test facility named ICARE EXPERIMENTAL are presented. ICARE EXPERIMENTAL was built in order to measure simultaneously the vibrations of four fuel assemblies (2 x 2) under an axial flow. Vibrations are produced by imposing the dynamic of one of the fuel assemblies and the displacements of the three others, induced by the fluid, are measured in the horizontal plane at grids level. A new data analysis method combining time-frequency analysis and orthogonal mode decomposition (POD) is described. This method, named Sliding Window POD (SWPOD), allows analysing multicomponent data, of which spatial repartition of energy and frequency content are time dependent. In the case of mechanical systems (linear and nonlinear), the link between the proper orthogonal modes obtained through SWPOD and the normal modes (linear and nonlinear) is studied. The SWPOD is applied to experimental tests of a steam generators U-tube, showing the appearance of internal resonances. The method is also applied to dynamic experimental tests of a fuel assembly under axial flow, the evolution of its normal modes is obtained as a function of the fluid velocity. The measures acquired with the ICARE EXPERIMENTAL installation are analysed using the SWPOD. The first results show characteristic behavior of the free fuel assemblies at their resonances. The coupling between fuel assemblies, induced by the fluid, is reproduced by simulations performed using the COEUR3D code. This code is based on a porous media model in order to simulate a fuel assemblies network under axial flow. (author) [fr
Logistics costs of the enterprise
Andrea Rosová
2007-06-01
Full Text Available The article describe a problem of specification and systematization of enterprise’s logistics costs. With in a growing division of labour, also logistics costs increase their part in enterprises total costs.Almost all decisions about products and production in general, influence logistics processes even logistics costs and performances.In present is not clear enough, which of the cost-particles are relevant fot logistics costs, because some of logistics cost-particles accounts within overhead are charged together with costs of other sorts.Substantive step in the process of the monitoring and evidence of logistics costs is definition of this, that costs of enterprise´s processes will be inclusive in logistics costs and determining points of contact with the others departments (acquisition, production, sale etc.. After the specification of meditation processes, there is a need to choose applicable parameters for the expression of logistics performances. Besides logistics costs is needed to know logistics performances equivalent herewith at a cost of, therefore from the control side have for enterprise bigger value indices expressive correlation costs and performances(e.g. share of logistics unit costs performance.At the proposal and evidence of logistics costs and performances is needed consistently entertain an individual conditions of enterprise. Because the area of processes included strongly affects the size of account logistics costs and its share part in total costs of enterprise. Logistics costs are flow line between economy and logistics of the enterprise.
Robustness Property of Robust-BD Wald-Type Test for Varying-Dimensional General Linear Models
Xiao Guo
2018-03-01
Full Text Available An important issue for robust inference is to examine the stability of the asymptotic level and power of the test statistic in the presence of contaminated data. Most existing results are derived in finite-dimensional settings with some particular choices of loss functions. This paper re-examines this issue by allowing for a diverging number of parameters combined with a broader array of robust error measures, called “robust- BD ”, for the class of “general linear models”. Under regularity conditions, we derive the influence function of the robust- BD parameter estimator and demonstrate that the robust- BD Wald-type test enjoys the robustness of validity and efficiency asymptotically. Specifically, the asymptotic level of the test is stable under a small amount of contamination of the null hypothesis, whereas the asymptotic power is large enough under a contaminated distribution in a neighborhood of the contiguous alternatives, thus lending supports to the utility of the proposed robust- BD Wald-type test.
Peng, Quanling; Xu, Fengyu; Wang, Ting; Yang, Xiangchen; Chen, Anbin; Wei, Xiaotao; Gao, Yao; Hou, Zhenhua; Wang, Bing; Chen, Yuan; Chen, Haoshu
2014-01-01
A batch superconducting solenoid magnet for the ADS proton linear accelerator has been designed, fabricated, and tested in a vertical dewar in Sept. 2013. A total of ten superconducting magnets will be installed into two separate cryomodules. Each cryomodule contains six superconducting spoke RF cavities for beam acceleration and five solenoid magnets for beam focusing. The multifunction superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction. The design current for the solenoid magnet is 182 A. A quench performance test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A, 308 A). The integrated field strength and leakage field at the nearby superconducting spoke cavities all meet the design requirements. The vertical test checked the reliability of the test dewar and the quench detection system. This paper presents the physical and mechanical design of the batch magnets, the quench detection technique, field measurements, and a discussion of the residual field resulting from persistent current effects
Cohen, B.L.
1992-01-01
A plot of lung-cancer rates versus radon exposures in 965 US counties, or in all US states, has a strong negative slope, b, in sharp contrast to the strong positive slope predicted by linear/no-threshold theory. The discrepancy between these slopes exceeds 20 standard deviations (SD). Including smoking frequency in the analysis substantially improves fits to a linear relationship but has little effect on the discrepancy in b, because correlations between smoking frequency and radon levels are quite weak. Including 17 socioeconomic variables (SEV) in multiple regression analysis reduces the discrepancy to 15 SD. Data were divided into segments by stratifying on each SEV in turn, and on geography, and on both simultaneously, giving over 300 data sets to be analyzed individually, but negative slopes predominated. The slope is negative whether one considers only the most urban counties or only the most rural; only the richest or only the poorest; only the richest in the South Atlantic region or only the poorest in that region, etc., etc.,; and for all the strata in between. Since this is an ecological study, the well-known problems with ecological studies were investigated and found not to be applicable here. The open-quotes ecological fallacyclose quotes was shown not to apply in testing a linear/no-threshold theory, and the vulnerability to confounding is greatly reduced when confounding factors are only weakly correlated with radon levels, as is generally the case here. All confounding factors known to correlate with radon and with lung cancer were investigated quantitatively and found to have little effect on the discrepancy
Radiosurgery and the double logistic product formula
Flickinger, J.C.; Steiner, L.
1990-01-01
The double logistic product formula is proposed as a method for predicting the probability of developing brain necrosis after high dose irradiation of small target volumes as used in stereotactic radiosurgery. Dose-response data observed for the production of localized radiation necreosis for treating intractable pain with the original Leksell gamma unit were used to choose the best fitting parameters for the double logistic product formula. This model can be used with either exponential or linear quadratic formulas to account for the effects of dose, fractionation and time in addition to volume. Dose-response predictions for stereotactic radiosurgery with different sized collimators are presented. (author). 41 refs.; 5 figs.; 1 tab
Cost Calculation Model for Logistics Service Providers
Zoltán Bokor
2012-11-01
Full Text Available The exact calculation of logistics costs has become a real challenge in logistics and supply chain management. It is essential to gain reliable and accurate costing information to attain efficient resource allocation within the logistics service provider companies. Traditional costing approaches, however, may not be sufficient to reach this aim in case of complex and heterogeneous logistics service structures. So this paper intends to explore the ways of improving the cost calculation regimes of logistics service providers and show how to adopt the multi-level full cost allocation technique in logistics practice. After determining the methodological framework, a sample cost calculation scheme is developed and tested by using estimated input data. Based on the theoretical findings and the experiences of the pilot project it can be concluded that the improved costing model contributes to making logistics costing more accurate and transparent. Moreover, the relations between costs and performances also become more visible, which enhances the effectiveness of logistics planning and controlling significantly
A Solution to Separation and Multicollinearity in Multiple Logistic Regression.
Shen, Jianzhao; Gao, Sujuan
2008-10-01
In dementia screening tests, item selection for shortening an existing screening test can be achieved using multiple logistic regression. However, maximum likelihood estimates for such logistic regression models often experience serious bias or even non-existence because of separation and multicollinearity problems resulting from a large number of highly correlated items. Firth (1993, Biometrika, 80(1), 27-38) proposed a penalized likelihood estimator for generalized linear models and it was shown to reduce bias and the non-existence problems. The ridge regression has been used in logistic regression to stabilize the estimates in cases of multicollinearity. However, neither solves the problems for each other. In this paper, we propose a double penalized maximum likelihood estimator combining Firth's penalized likelihood equation with a ridge parameter. We present a simulation study evaluating the empirical performance of the double penalized likelihood estimator in small to moderate sample sizes. We demonstrate the proposed approach using a current screening data from a community-based dementia study.
Steganalysis using logistic regression
Lubenko, Ivans; Ker, Andrew D.
2011-02-01
We advocate Logistic Regression (LR) as an alternative to the Support Vector Machine (SVM) classifiers commonly used in steganalysis. LR offers more information than traditional SVM methods - it estimates class probabilities as well as providing a simple classification - and can be adapted more easily and efficiently for multiclass problems. Like SVM, LR can be kernelised for nonlinear classification, and it shows comparable classification accuracy to SVM methods. This work is a case study, comparing accuracy and speed of SVM and LR classifiers in detection of LSB Matching and other related spatial-domain image steganography, through the state-of-art 686-dimensional SPAM feature set, in three image sets.
Brunet, M.; Morestin, F.; Godereaux, S.
2000-01-01
An inverse identification technique is proposed based on bending-unbending experiments on anisotropic sheet-metal strips. The initial anisotropy theory of plasticity is extended to include the concept of combined isotropic and non-linear kinematic hardening. This theory is adopted to characterise the anisotropic hardening due to loading-unloading which occurs in sheet-metal forming processes. To this end, a specific bending-unbending apparatus has been built to provide experimental moment-curvature curves. The constant bending moment applied over the length of the specimen to determine numerically the strain-stress behaviour but without Finite Element Analysis. Four constitutive parameters have to be identified by an inverse approach. Our identification results show that bending-unbending tests are suitable to model quite accurately the constitutive behaviour of sheet metals under complex loading paths. (author)
Education in logistics and training of non-logistic personnel
Marko D. Andrejić
2011-01-01
Full Text Available The significance of education in logistics and education and training of cadets who belong to non-logistic services (non-logistic personnel will be presented. The logistical aspects of education of non-logistic personnel are elaborated as well as the knowledge in the area of logistics which is necessary to be transferred through the educational process to non-logistic personnel for the successful accomplishment of their functional duties. A general approach and the methods of logistics education and improvement of non-logistic personnel are presented as well as the institutional prerequisites necessary for improving the quality of logistics education and training. The quality of the knowledge in this area and its implementation into the methods of thinking and decision making of non-logistic personnel affect the cooperation between the non-logistic and the logistic personnel, directly contributing to the quality of life and working conditions of units and institutions as well as to the quality and synergy in task accomplishments in the framework defined by the missions of the Army of Serbia. The necessary content and means of its transfer to cadets are discussed since they are supposed to be available at all levels and forms of education, depending on the previous cadet education levels. The theoretical bases and experiences shown are of general character and they have a universal application in the process of education. Introduction In our recent defense theory and operational practice, logistics education of non-logistic personnel is not sufficiently analyzed either in organizational or technological aspects, considering the concept and the logic of a systematic and a situational approach. The analysis of the experiences gained from operational practice shows a slight decrease in the quality of task accomplishment due to the lack of necessary logistic knowledge and habits as well as an increased communication gap between logistic and non-logistic
Secolsky, Charles; Krishnan, Sathasivam; Judd, Thomas P.
2013-01-01
The community colleges in the state of New Jersey went through a process of establishing statewide cut-off scores for English and mathematics placement tests. The colleges wanted to communicate to secondary schools a consistent preparation that would be necessary for enrolling in Freshman Composition and College Algebra at the community college…
Logistics in Estonian business companies
A. Kiisler
2008-12-01
Full Text Available The article describes logistics survey in Estonia carried out in 2007 as a part of the LogOnBaltic project. The level of logistics in Estonian manufacturing, trading and logistics companies is explored through logistics costs, performance indicators, outsourcing, ICT use and logistics self-estimation of the companies responded. Responses from 186 Estonian companies were gathered through a web-based survey (38% of manufacturing, 38% of trading and 24% of logistics sector. Logistics costs as the percentage of turnover make in average 13.8% in manufacturing and 13.3% in trading. Transportation and inventory carrying cost form around 70% of overall logistics costs. Considering the logistics indicators surveyed, Estonian companies show up with relatively low perfect order fulfillment rates, short customer order fulfillment cycles and effective management of cash flows. The most widely outsourced logistics function is international transportation followed by domestic transportation, freight forwarding and reverse logistics. By 2010, the outsourcing of IT systems in logistics followed by inventory management, warehousing and product customization is expected to increase more substantially. The awareness of logistics importance is still low among Estonian companies. Only 27–44% of those agree that logistics has a considerable impact on profitability, competitive advantage, top management or customer service level.
Logistic chaotic maps for binary numbers generations
Kanso, Ali; Smaoui, Nejib
2009-01-01
Two pseudorandom binary sequence generators, based on logistic chaotic maps intended for stream cipher applications, are proposed. The first is based on a single one-dimensional logistic map which exhibits random, noise-like properties at given certain parameter values, and the second is based on a combination of two logistic maps. The encryption step proposed in both algorithms consists of a simple bitwise XOR operation of the plaintext binary sequence with the keystream binary sequence to produce the ciphertext binary sequence. A threshold function is applied to convert the floating-point iterates into binary form. Experimental results show that the produced sequences possess high linear complexity and very good statistical properties. The systems are put forward for security evaluation by the cryptographic committees.
Edwards, Harold M
1995-01-01
In his new undergraduate textbook, Harold M Edwards proposes a radically new and thoroughly algorithmic approach to linear algebra Originally inspired by the constructive philosophy of mathematics championed in the 19th century by Leopold Kronecker, the approach is well suited to students in the computer-dominated late 20th century Each proof is an algorithm described in English that can be translated into the computer language the class is using and put to work solving problems and generating new examples, making the study of linear algebra a truly interactive experience Designed for a one-semester course, this text adopts an algorithmic approach to linear algebra giving the student many examples to work through and copious exercises to test their skills and extend their knowledge of the subject Students at all levels will find much interactive instruction in this text while teachers will find stimulating examples and methods of approach to the subject
Jakov Karmelić
2012-05-01
Full Text Available Within the whole world container traffic, the largest share of containers is in the status of repositioning. Container repositioning results from the need for harmonization between the point of empty container accumulation and the point of demand, and waiting time for the availability of the first next transport of cargo. This status of containers on the container market is the consequence of imbalances in the worldwide trade distribution on most important shipping routes. The need for fast and effective reallocation of empty containers causes high costs and often represents an obstacle affecting the efficiency of port container terminals and inland carriers.In accordance with the above issue, this paper is mainly focused on the analysis of the data concerning global container capacities and the roots of container equipment imbalances, with the aim of determining the importance of empty container management and the need for empty container micro-logistic planning at the spread port area.
Holmes, Tyson H; Li, Shou-Hua; McCann, David J
2016-11-23
The design of pharmacological trials for management of substance use disorders is shifting toward outcomes of successful individual-level behavior (abstinence or no heavy use). While binary success/failure analyses are common, McCann and Li (CNS Neurosci Ther 2012; 18: 414-418) introduced "number of beyond-threshold weeks of success" (NOBWOS) scores to avoid dichotomized outcomes. NOBWOS scoring employs an efficacy "hurdle" with values reflecting duration of success. Here, we evaluate NOBWOS scores rigorously. Formal analysis of mathematical structure of NOBWOS scores is followed by simulation studies spanning diverse conditions to assess operating characteristics of five linear-rank tests on NOBWOS scores. Simulations include assessment of Fisher's exact test applied to hurdle component. On average, statistical power was approximately equal for five linear-rank tests. Under none of conditions examined did Fisher's exact test exhibit greater statistical power than any of the linear-rank tests. These linear-rank tests provide good Type I and Type II error control for comparing distributions of NOBWOS scores between groups (e.g. active vs. placebo). All methods were applied to re-analyses of data from four clinical trials of differing lengths and substances of abuse. These linear-rank tests agreed across all trials in rejecting (or not) their null (equality of distributions) at ≤ 0.05. © The Author(s) 2016.
Leif E. Peterson
1997-11-01
Full Text Available A computer program for multifactor relative risks, confidence limits, and tests of hypotheses using regression coefficients and a variance-covariance matrix obtained from a previous additive or multiplicative regression analysis is described in detail. Data used by the program can be stored and input from an external disk-file or entered via the keyboard. The output contains a list of the input data, point estimates of single or joint effects, confidence intervals and tests of hypotheses based on a minimum modified chi-square statistic. Availability of the program is also discussed.
Reddy, Dhananjaya
2011-01-01
In the competitive world of manufacturing, companies are often searching for new ways to improve their process, customer satisfaction and stay ahead in the game with their competitors. Reverse logistics has been considered a strategy to bring these things to life for the past decade or so. This thesis work tries to shed some light on the basics of reverse logistics and how reverse logistics can be used as a management strategy. This paper points out the fundamentals of reverse logistics and l...
Kamaruddin, Ainur Amira; Ali, Zalila; Noor, Norlida Mohd.; Baharum, Adam; Ahmad, Wan Muhamad Amir W.
2014-07-01
Logistic regression analysis examines the influence of various factors on a dichotomous outcome by estimating the probability of the event's occurrence. Logistic regression, also called a logit model, is a statistical procedure used to model dichotomous outcomes. In the logit model the log odds of the dichotomous outcome is modeled as a linear combination of the predictor variables. The log odds ratio in logistic regression provides a description of the probabilistic relationship of the variables and the outcome. In conducting logistic regression, selection procedures are used in selecting important predictor variables, diagnostics are used to check that assumptions are valid which include independence of errors, linearity in the logit for continuous variables, absence of multicollinearity, and lack of strongly influential outliers and a test statistic is calculated to determine the aptness of the model. This study used the binary logistic regression model to investigate overweight and obesity among rural secondary school students on the basis of their demographics profile, medical history, diet and lifestyle. The results indicate that overweight and obesity of students are influenced by obesity in family and the interaction between a student's ethnicity and routine meals intake. The odds of a student being overweight and obese are higher for a student having a family history of obesity and for a non-Malay student who frequently takes routine meals as compared to a Malay student.
The Emergence of City Logistics
Gammelgaard, Britta; Aastrup, Jesper
2014-01-01
Purpose: Many city logistics projects in Europe have failed. The purpose of this article is to increase understanding of how city logistics emerge. A better understanding of the complex organizational processes with many actors and stakeholders in city logistics projects may prevent further failu...
Satellite rainfall retrieval by logistic regression
Chiu, Long S.
1986-01-01
The potential use of logistic regression in rainfall estimation from satellite measurements is investigated. Satellite measurements provide covariate information in terms of radiances from different remote sensors.The logistic regression technique can effectively accommodate many covariates and test their significance in the estimation. The outcome from the logistical model is the probability that the rainrate of a satellite pixel is above a certain threshold. By varying the thresholds, a rainrate histogram can be obtained, from which the mean and the variant can be estimated. A logistical model is developed and applied to rainfall data collected during GATE, using as covariates the fractional rain area and a radiance measurement which is deduced from a microwave temperature-rainrate relation. It is demonstrated that the fractional rain area is an important covariate in the model, consistent with the use of the so-called Area Time Integral in estimating total rain volume in other studies. To calibrate the logistical model, simulated rain fields generated by rainfield models with prescribed parameters are needed. A stringent test of the logistical model is its ability to recover the prescribed parameters of simulated rain fields. A rain field simulation model which preserves the fractional rain area and lognormality of rainrates as found in GATE is developed. A stochastic regression model of branching and immigration whose solutions are lognormally distributed in some asymptotic limits has also been developed.
Design of a non-linear power take-off simulator for model testing of rotating wave energy devices
Lopes, M.F.P.; Henriques, J.C.C.; Lopes, Miguel C.; Gato, L.M.C. [IDMEC - Instituto de Engenharia Mecanica, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Lisboa (Portugal); Dente Antonio [CIE3 - Center for Innovation in Electrical and Energy Engineering, Lisboa (Portugal)
2009-07-01
Eddy current brakes provide a versatile way of simulating the power take-off system (PTO) in the model testing of wave energy converters at small scale. These are based on the principle that a conductive material moving perpendicularly to a magnetic field generates a braking force proportional to its velocity. This was applied in the design of the PTO simulator of a bottom-hinged flap wave energy converter model, at 1/16 scale. The efforts put into the accurate dynamic simulation of the device led to the development of a controllable PTO simulator, which can be applied to other small scale rotating wave energy device models. A special power source was built to provide the required controllable current intensity to feed the magnetic field generating coils. Different non-linear damping PTO characteristic curves can be simulated by basing the current control on real-time velocity measurement. The calibration of the system was done by connecting the device to a constant rotating speed motor and measuring the resistent torque produced by the PTO with a torquemeter for different values of current intensity through the coils.
Pequegnot, Anne-Laure
2013-01-01
The LHC is currently the most powerful accelerator in the world. This proton-proton collider is now stoppped to increase significantly its luminosity and energy, which would provide a larger discovery potential in 2014 and beyond. A high-energy $e^{+}e^{-}$ collider, such as CLIC, is an option to complement and to extend the LHC physics programme. Indeed, a lepton collider gives access to additional physics processes, beyond those observable at the LHC, and therefore provides new discovery potential. It can also provide complementary and/or more precise information about new physics uncovered at the LHC. Many essential features of a detector are required to deliver the full physics potential of this CLIC machine. In this present report, I present my work on the vertex detector R\\&D for this future linear collider, which aims at developping highly granular and ultra-thin position sensitive detection devices with very low power consumption and fast time-stamping capability. We tested here thin silicon pixel...
Vincent, Patrick J
2006-01-01
.... Specific research tasks could focus on feasibility studies, cost-benefit analyses, modeling and simulation, front-end analyses, field test support activities, and demonstration system development...
Logistics centres development in Latvia
I. Kabashkin
2007-12-01
Full Text Available In the situation where a large increase in trade and freight transport volumes in the Baltic Sea region (BSR is expected and in which the BSR is facing a major economic restructuring, eff orts to achieve more integrated and sustainable transport and communication links within the BSR are needed. One of these eff orts is the development of logistics centres (LCs and their networking, which will continue to have an impact on improving communication links, spatial planning practices and approaches, logistics chain development and the promotion of sustainable transport modes. These factors will refl ect on logistics processes both in major gateway cities and in remote BSR areas. The importance of logistics systems as a whole is not seen clearly enough. Logistics actors see that logistics operations are not appreciated as much as other fi elds of activity. In addition, logistics centres and the importance of logistics activities to the business life of areas and the employment rate should be brought up better. In the paper main goal and tasks of national approach to LCs development are discussed. Strategic focus of new activities in this area is on the integration of various networks within and between logistics centres in order to improve and develop the quality of logistics networks as well as to spatially widen the networking activities. The key objectives are to integrate the links between logistics centres, ports and other logistics operators in a functional and sustainable way, to promote spatial integration by creating sustainable and integrated approaches to spatial planning of logistics centres and transport infrastructure, to improve ICT-based networking and communication practices of the fi elds of transport and logistics and to increase the competence of logistics centres and associated actors by organising educational and training events. The current activities include, for example, the creation of measures for transport networking and
A Mathematical Model to Improve the Performance of Logistics Network
Muhammad Izman Herdiansyah
2012-01-01
Full Text Available The role of logistics nowadays is expanding from just providing transportation and warehousing to offering total integrated logistics. To remain competitive in the global market environment, business enterprises need to improve their logistics operations performance. The improvement will be achieved when we can provide a comprehensive analysis and optimize its network performances. In this paper, a mixed integer linier model for optimizing logistics network performance is developed. It provides a single-product multi-period multi-facilities model, as well as the multi-product concept. The problem is modeled in form of a network flow problem with the main objective to minimize total logistics cost. The problem can be solved using commercial linear programming package like CPLEX or LINDO. Even in small case, the solver in Excel may also be used to solve such model.Keywords: logistics network, integrated model, mathematical programming, network optimization
The Emergence of City Logistics
Gammelgaard, Britta
2015-01-01
is therefore to increase understanding of how city logistics emerge, and secondarily, to investigate whether such processes can be managed at all. Design/methodology/approach: – A paradigm shift in urban planning creates new ways of involving stakeholders in new sustainability measures such as city logistics...... dialectic forces were at play. City logistics schemes are still in an innovation phase. The biggest challenge in managing a process toward city logistics is to convince the many public and private stakeholders of their mutual interest and goals. Research limitations/implications: – Urban goods transport...... city logistics projects may fail. Thereby, cities become more environmentally and socially sustainable. Originality/value: – Insights into a city logistics project from a change management perspective has not previously been reported in literature....
Outsourcing Operational Logistics: Buyer Beware
2003-05-16
This logistics system takes far too many people to conduct support missions and does not provide the desired customer performance in terms of...FINAL 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER OUTSOURCING OPERATIONAL LOGISTICS: BUYER BEWARE (U) 5b. GRANT NUMBER 5c...Form 298 (Rev. 8-98) 1 (Unclassified Paper) NAVAL WAR COLLEGE Newport, R.I. OUTSOURCING OPERATIONAL LOGISTICS: BUYER BEWARE By LAMONT WOODY Lieutenant
Logistics Reduction: Heat Melt Compactor
National Aeronautics and Space Administration — The Advanced Exploration Systems (AES) Logistics Reduction (LR) project Heat Melt Compactor (HMC) technology is a waste management technology. Currently, there are...
Situational Awareness and Logistics Division
Federal Laboratory Consortium — Volpe's Situational Awareness and Logistics Division researches, develops, implements, and analyzes advanced systems to protect, enhance, and ensure resilienceof the...
In-plant logistics optimalization
Maroušek, Jan
2008-01-01
In a theoretical part of this work there is introduced a general view on logistics and its development, than a view on creating value for customer, basics of lean production, lean thinking and following methods as Six Sigma and Value Stream Mapping. At the end of the theoretical part there is mentioned outsourcing of logistics services and view on relationship between logistics provider and a client. In a practical part there is introduced a project of in-plant logistics optimalization in a f...
A note on Verhulst's logistic equation and related logistic maps
Gutierrez, M Ranferi; Reyes, M A; Rosu, H C
2010-01-01
We consider the Verhulst logistic equation and a couple of forms of the corresponding logistic maps. For the case of the logistic equation we show that using the general Riccati solution only changes the initial conditions of the equation. Next, we consider two forms of corresponding logistic maps reporting the following results. For the map x n+1 = rx n (1 - x n ) we propose a new way to write the solution for r = -2 which allows better precision of the iterative terms, while for the map x n+1 - x n = rx n (1 - x n+1 ) we show that it behaves identically to the logistic equation from the standpoint of the general Riccati solution, which is also provided herein for any value of the parameter r.
Walker, Salma C.; Rachmeler, Laurel; Winebarger, Amy; Champey, Patrick; Bethge, Christian
2018-01-01
To unveil the complexity of the solar atmosphere, measurement of the magnetic field in the upper chromosphere and transition region is fundamentally important, as this is where the forces transition from plasma to magnetic field dominated. Measurements of the field are also needed to elucidate the energy transport from the lower atmospheric regions to the corona beyond. Such an advance in heliospheric knowledge became possible with the first flight of the international solar sounding rocket mission, CLASP. For the first time, linear polarization was measured in Hydrogen Lyman-Alpha at 121.60 nm in September 2015. For linear polarization measurements in this emission line, high sensitivity is required due to the relatively weak polarization signal compared to the intensity. To achieve this high sensitivity, a low-noise sensor is required with good knowledge of its characterization, including linearity. This work presents further refinement of the linearity characterization of the cameras flown in 2015. We compared the current from a photodiode in the light path to the digital response of the detectors. Pre-flight CCD linearity measurements were taken for all three flight cameras and calculations of the linear fits and residuals were performed. However, the previous calculations included a smearing pattern and a digital saturation region on the detectors which were not properly taken into account. The calculations have been adjusted and were repeated for manually chosen sub-regions on the detectors that were found not to be affected. We present a brief overview of the instrument, the calibration data and procedures, and a comparison of the old and new linearity results. The CLASP cameras will be reused for the successor mission, CLASP2, which will measure the Magnesium II h & k emission lines between 279.45 nm and 280.35 nm. The new approach will help to better prepare for and to improve the camera characterization for CLASP2.
Walker, S. C.; Rachmeler, L.; Winebarger, A. R.; Champey, P. R.; Bethge, C.
2017-12-01
To unveil the complexity of the solar atmosphere, measurement of the magnetic field in the upper chromosphere and transition region is fundamentally important, as this is where the forces transition from plasma to magnetic field dominated. Measurements of the field are also needed to shed light on the energy transport from the lower atmospheric regions to the corona beyond. Such an advance in heliospheric knowledge became possible with the first flight of the international solar sounding rocket mission, CLASP. For the first time, linear polarization was measured in H Lyman-Alpha at 121.60 nm in September 2015. For linear polarization measurements in this line, high sensitivity is required due to the relatively weak polarization signal compared to the intensity. To achieve this high sensitivity, a low-noise sensor is required with good knowledge of its characterization, including linearity. This work presents further refinement of the linearity characterization of the cameras flown in 2015. We compared the current from a photodiode in the light path to the digital response of the detectors. Pre-flight CCD linearity measurements were taken for all three flight cameras and calculations of the linear fits and residuals were performed. However, the previous calculations included a smearing pattern and a digital saturation region on the detectors which were not properly taken into account. The calculations have been adjusted and were repeated for manually chosen sub-regions on the detectors that were found not to be affected. We present a brief overview of the instrument, the calibration data and procedures, and a comparison of the old and new linearity results. The CLASP cameras will be reused for the successor mission, CLASP2, which will measure the Mg II h & k lines between 279.45 nm and 280.35 nm. The new approach will help to better prepare for and to improve the camera characterization for CLASP2.
Outsourcing Operational Logistics: Buyer Beware
Woody, Lamont
2003-01-01
One of the key tasks from U.S. Secretary of Defense Donald H. Rumsfeld to his Service Chiefs is to reduce DOD's overall logistic cost and footprint while transforming the warfighter-to-logistics (tooth-to-tail) force structure...
Logistic Regression: Concept and Application
Cokluk, Omay
2010-01-01
The main focus of logistic regression analysis is classification of individuals in different groups. The aim of the present study is to explain basic concepts and processes of binary logistic regression analysis intended to determine the combination of independent variables which best explain the membership in certain groups called dichotomous…
Information Logistics Research report 2
Willems, A.; Hajdasinski, A.K.; Willems, J.
2009-01-01
The goal of this research report is to further explore the concept of Information Logistics (IL), which refers to the usage and dispatch of information and methods of logistics able to support those processes. This report is based upon 6 questions that examine IL in organizations, healthcare
Simulation Integrated Design for Logistics
Veeke, H.P.M.
2003-01-01
The design of an innovative logistic system is a complex problem in the solution of which many disciplines are involved. Each discipline developed its own way of conceptual modeling for a logistic system based on a mono disciplinary perception. In essence this leads to a communication problem
Transport, logistics and the region
Langen, de P.W.
2010-01-01
Cargo transport and logistics have a huge impact on sustainable (regional) economic development. Two broad (policy) challenges are center stage: enhancing co-location of logistics activities and improving efficiency in intermodal transport chains. Academic research can provide relevant insights for
Shieh, Gwowen; Jan, Show-Li
2015-01-01
The general formulation of a linear combination of population means permits a wide range of research questions to be tested within the context of ANOVA. However, it has been stressed in many research areas that the homogeneous variances assumption is frequently violated. To accommodate the heterogeneity of variance structure, the…
Le Kernec, Julien; Dreuillet, Philippe; Bobillot, Gerard; Garda, Patrick; Romain, Olivier; Denoulet, Julien
2009-01-01
This paper presents a experimental platform that allows comparing objectively any radar waveforms. This is realized by equating radar characteristics, using the same test-bench HYCAM-Research, the same signal processing and also insuring the reproducibility of the experiments. The experimental measurements on linear chirp and multitones are analyzed through distance and velocity imaging.
Quality of investments in logistics
Borut Jereb
2014-06-01
Full Text Available The issue problem of paper is that base on researches connected with analysis of investments in logistics based on the review of 100 pooled manuscripts from different sources (scientific journals and online magazines from 1996 to 2012 it was showed that there don't exist quality as well as leadership has no a good overview of the investment in logistics. It was claimed that the quality point of view should be demanding part of investments in logistics. Val Log was proposed as an answer to the issues of managing quality of investments in logistics at the tactical level in organizations. By Val Log it is possible to overcome the myth that logistics projects cost money while business projects bring money. Val Log also provides detailed instructions for goals and metrics for each process. By doing changes the quality should be the obvious pillar of our affords doing it.
IMPROVING HOSPITAL LOGISTICS BY RETHINKING TECHNOLOGY ASSESSMENT
Jacobsen, Peter; Jørgensen, Pelle Morten Thomas
2011-01-01
In order to cope with the future challenges of the health care sector, there is an urging need for improving efficiency at hospitals. The study presents a framework enabling health care managers of improving the in-house logistics. The distinctiveness of the framework is the way in which it relates...... technology, logistics, structure and procedures to efficiency. Changing one factor e.g. technology, initiates an iterative loop focusing on change in the related factors in order to obtain the optimal efficiency. The search for an optimal efficient solution is the driving force of the framework...... at a Danish hospital. The framework is tested on the blood sample logistics between the emergency department and laboratory with the goal of enhancing the efficiency of the emergency department....
Lin, Yingzhi; Deng, Xiangzheng; Li, Xing; Ma, Enjun
2014-12-01
Spatially explicit simulation of land use change is the basis for estimating the effects of land use and cover change on energy fluxes, ecology and the environment. At the pixel level, logistic regression is one of the most common approaches used in spatially explicit land use allocation models to determine the relationship between land use and its causal factors in driving land use change, and thereby to evaluate land use suitability. However, these models have a drawback in that they do not determine/allocate land use based on the direct relationship between land use change and its driving factors. Consequently, a multinomial logistic regression method was introduced to address this flaw, and thereby, judge the suitability of a type of land use in any given pixel in a case study area of the Jiangxi Province, China. A comparison of the two regression methods indicated that the proportion of correctly allocated pixels using multinomial logistic regression was 92.98%, which was 8.47% higher than that obtained using logistic regression. Paired t-test results also showed that pixels were more clearly distinguished by multinomial logistic regression than by logistic regression. In conclusion, multinomial logistic regression is a more efficient and accurate method for the spatial allocation of land use changes. The application of this method in future land use change studies may improve the accuracy of predicting the effects of land use and cover change on energy fluxes, ecology, and environment.
Yokoyama, Kenji; Ishikawa, Makoto
2000-04-01
The linear heat rates of the power-to-melt (PTM) tests, performed with B5D-1 and B5D-2 subassemblies on the Experimental Fast Reactor 'JOYO', are evaluated with the continuous energy Monte-Carlo code, MVP. We can apply a whole core model to MVP, but it takes very long time for the calculation. Therefore, judging from the structure of B5D subassembly, we used the MVP code to calculate the radial distribution of linear heat rate and used the deterministic method to calculate the axial distribution. We also derived the formulas for this method. Furthermore, we evaluated the error of the linear heat rate, by evaluating the experimental error of the reactor power, the statistical error of Monte-Carlo method, the calculational model error of the deterministic method and so on. On the other hand, we also evaluated the burnup rate of the B5D assembly and compared with the measured value in the post-irradiation test. The main results are following: B5D-1 (B5101, F613632, core center). Linear heat rate: 600 W/cm±2.2%. Burnup rate: 0.977. B5D-2 (B5214, G80124, core center). Linear heat rate: 641 W/cm±2.2%. Burnup rate: 0.886. (author)
Morrow, A; Rangaraj, D; Perez-Andujar, A; Krishnamurthy, N
2016-01-01
Purpose: This work’s objective is to determine the overlap of processes, in terms of sub-processes and time, between acceptance testing and commissioning of a conventional medical linear accelerator and to evaluate the time saved by consolidating the two processes. Method: A process map for acceptance testing for medical linear accelerators was created from vendor documentation (Varian and Elekta). Using AAPM TG-106 and inhouse commissioning procedures, a process map was created for commissioning of said accelerators. The time to complete each sub-process in each process map was evaluated. Redundancies in the processes were found and the time spent on each were calculated. Results: Mechanical testing significantly overlaps between the two processes - redundant work here amounts to 9.5 hours. Many beam non-scanning dosimetry tests overlap resulting in another 6 hours of overlap. Beam scanning overlaps somewhat - acceptance tests include evaluating PDDs and multiple profiles but for only one field size while commissioning beam scanning includes multiple field sizes and depths of profiles. This overlap results in another 6 hours of rework. Absolute dosimetry, field outputs, and end to end tests are not done at all in acceptance testing. Finally, all imaging tests done in acceptance are repeated in commissioning, resulting in about 8 hours of rework. The total time overlap between the two processes is about 30 hours. Conclusion: The process mapping done in this study shows that there are no tests done in acceptance testing that are not also recommended to do for commissioning. This results in about 30 hours of redundant work when preparing a conventional linear accelerator for clinical use. Considering these findings in the context of the 5000 linacs in the United states, consolidating acceptance testing and commissioning would have allowed for the treatment of an additional 25000 patients using no additional resources.
Morrow, A [Scott & White Hospital Temple, TX (United States); Rangaraj, D [Baylor Scott & White Health, Temple, TX (United States); Perez-Andujar, A [University of California San Francisco, San Francisco, CA (United States); Krishnamurthy, N [Baylor Scott & White Healthcare, Temple, TX (United States)
2016-06-15
Purpose: This work’s objective is to determine the overlap of processes, in terms of sub-processes and time, between acceptance testing and commissioning of a conventional medical linear accelerator and to evaluate the time saved by consolidating the two processes. Method: A process map for acceptance testing for medical linear accelerators was created from vendor documentation (Varian and Elekta). Using AAPM TG-106 and inhouse commissioning procedures, a process map was created for commissioning of said accelerators. The time to complete each sub-process in each process map was evaluated. Redundancies in the processes were found and the time spent on each were calculated. Results: Mechanical testing significantly overlaps between the two processes - redundant work here amounts to 9.5 hours. Many beam non-scanning dosimetry tests overlap resulting in another 6 hours of overlap. Beam scanning overlaps somewhat - acceptance tests include evaluating PDDs and multiple profiles but for only one field size while commissioning beam scanning includes multiple field sizes and depths of profiles. This overlap results in another 6 hours of rework. Absolute dosimetry, field outputs, and end to end tests are not done at all in acceptance testing. Finally, all imaging tests done in acceptance are repeated in commissioning, resulting in about 8 hours of rework. The total time overlap between the two processes is about 30 hours. Conclusion: The process mapping done in this study shows that there are no tests done in acceptance testing that are not also recommended to do for commissioning. This results in about 30 hours of redundant work when preparing a conventional linear accelerator for clinical use. Considering these findings in the context of the 5000 linacs in the United states, consolidating acceptance testing and commissioning would have allowed for the treatment of an additional 25000 patients using no additional resources.
Analysis and testing of a double armature brushless dc linear motor with NdFeB permanent magnets
Filho, A.F.F.
1998-01-01
The use of high-energy product NdFeB permanent magnets benefits the design and features of a double armature brushless dc linear motor. As the linear motor is also slotless, its 5 mm airgap requires a source of high flux to overcome the reluctance and produce an adequate amount of force. The linear motor employs a topology that makes use of five permanent magnets to provide excitation flux. The permanent magnets are arranged in such a way that maximises the force the linear motor can deliver. The actuator produces a force up to 86.2 N at an armature current of 4.5 A. However, the topology makes the actuator prone to saturation. It affects the operation point of the permanent magnets, reduces the airgap flux density and the force, and increases flux leakage. To avoid saturation, a flux compensation scheme was conceived. The results are presented and assessed by means of finite element simulation and by experimental results that presented a good agreement. (orig.)
TENVERGERT, E; GILLESPIE, M; KINGMA, J
This paper shows how to use the log-linear subroutine of SPSS to fit the Rasch model. It also shows how to fit less restrictive models obtained by relaxing specific assumptions of the Rasch model. Conditional maximum likelihood estimation was achieved by including dummy variables for the total
The North American water and wastewater community has hundreds of millions of feet of ductile iron pipe in service. Only a portion of the inventory has any form of external corrosion control. Ductile iron pipe, in certain environments, is subject to external corrosion.Linear Pola...
Logistics planning and logistics planning factors for humanitarian operations
Sullivan, Donna Marie.
1995-01-01
Due to the increasing demand on the military to conduct humanitarian operations, the need for logistics planning factors that are applicable to these operations has arisen. This thesis develops a model for humanitarian operations and employs the model to develop logistics planning factors for material consumption and a computer-assisted planning aid relating to the support of the victim population. U.S. Navy (U.S.N.) author.
Saccomandi, Paola; Varalda, Ambra; Gassino, Riccardo; Tosi, Daniele; Massaroni, Carlo; Caponero, Michele A.; Pop, Raoul; Korganbayev, Sanzhar; Perrone, Guido; Diana, Michele; Vallan, Alberto; Costamagna, Guido; Marescaux, Jacques; Schena, Emiliano
2017-09-01
The response of a fiber optic sensor [linearly chirped fiber Bragg grating (LCFBG)] to a linear thermal gradient applied on its sensing length (i.e., 1.5 cm) has been investigated. After these bench tests, we assessed their feasibility for temperature monitoring during thermal tumor treatment. In particular, we performed experiments during ex vivo laser ablation (LA) in pig liver and in vivo thermal ablation in animal models (pigs). We investigated the following: (i) the relationship between the full width at half maximum of the LCFBG spectrum and the temperature difference among the extremities of the LCFBG and (ii) the relationship between the mean spectrum wavelength and the mean temperature acting on the LCFBG sensing area. These relationships showed a linear trend during both bench tests and LA in animal models. Thermal sensitivity was significant although different values were found with regards to bench tests and animal experiments. The linear trend and significant sensitivity allow hypothesizing a future use of this kind of sensor to monitor both temperature gradient and mean temperature within a tissue undergoing thermal treatment.
Shilov, Georgi E
1977-01-01
Covers determinants, linear spaces, systems of linear equations, linear functions of a vector argument, coordinate transformations, the canonical form of the matrix of a linear operator, bilinear and quadratic forms, Euclidean spaces, unitary spaces, quadratic forms in Euclidean and unitary spaces, finite-dimensional space. Problems with hints and answers.
Development of logistics information systems
Milan Ž. Dronjak
2012-10-01
Full Text Available An adequate logistics information system provides real time automated data processing, distribution and of information according to Terrain Commander's requirements, which leads to timely fulfillment of logistic demands of units. SAP ERP The SAP ERP application is the integrated (ERP software capable of working with complex organisational structures, personnel, equipment, and finance. It enables planning and combining forces for every type of operations. The system also enables the determination of the readiness status of modelled forces. ISL The Information System for Logistics (ISL is a comprehensive information system of the Ministry of Defence (MoD and the Army of the Czech Republic that covers many areas: acquisition, supply, ammunition and equipment maintenance, logistics, etc. The ISL provides support for military logistics in all important areas of consumer and acquisition logistics, satisfaying all kinds of Defence Forces needs in the country and abroad. LOGFAS The information system LOGFAS comprises Logistics Database (LOGBASE, Movement and Transportation software (M&T, Allied Command Europe Resource Optimisation Software System (ACROSS and Logistic Reporting System (LOGREP. The Logistics Database LOGBASE represents a logistics information source and also a database related to assets, forces, geography, infrastructure, targets, supplies, movements and medical data. The main software tools which rely on the LOGBASE are M&T, ACROSS and LOGREP. GCSS-Army The original impetus to create the SALE came in the mid-90s when the United States Department of Defense (DoD started a logistics modernisation programme. One of tasks was to build The Single Army Logistics Enterprise (SALE for the purpose of covering the whole organisational structure of the DoD. There are three components of the SALE: GCSS-Army, PLM+ and LMP. Each of them uses the commercial Enterprise Resource Planning SAP Software with a Web access. The main component, GCSS
Tomasko, D.; Jensen, A.L.
1987-07-01
Unlike previous interpretations of this test that used a double-porosity radial-flow model, this interpretation is based on a linear-flow process. Drawdowns in pumped well H-3b2 responded as if the Culebra Dolomite Member of the Rustler Formation were pumped from an elongated feature with a significantly higher permeability than the surrounding porous medium. Drawdowns in observation wells DOE-1 and H-11 exhibited nearly classic linear-flow behavior in specialty plots of drawdowns had excellent type-curve matches with a linear-flow type curve. The orientation of the linear feature using data from a multiwell interference test was found by minimizing the squared differences between field observations and linear flow calculations. A second technique was used to calculate the transmissivity and width of the feature. To calculate consistent system parameters, this technique required developing a least-squares fitting procedure to minimize the effects of noise in the drawdown measurements. While the underlying assumptions of the linear-flow model differ from those of a double-porosity radial-flow model, the properties calculated for the Culebra are similar to those previously presented and indicate a basic insensitivity to the system flow model. In addition to yielding hydrologic values that are approximately the same, the two models are complementary and provide unique information for characterizing the aquifer - double-porosity parameters from one model, and the orientation and width of a high-permeability elongated strip from the other. The two interpretations also provide a consistent picture of an extensively fractured porous medium in the vicinity of the H-3 hydropad. 24 refs., 27 figs., 3 tabs
Alyssa M. Cornall
2017-12-01
Full Text Available Purpose: To compare human papillomavirus genotype-specific performance of two genotyping assays, Anyplex II HPV28 (Seegene and EuroArray HPV (EuroImmun, with Linear Array HPV (Roche. Methods: DNA extracted from clinican-collected cervical brush specimens in PreservCyt medium (Hologic, from 403 women undergoing management for detected cytological abnormalities, was tested on the three assays. Genotype-specific agreement were assessed by Cohen's kappa statistic and Fisher's z-test of significance between proportions. Results: Agreement between Linear Array and the other 2 assays was substantial to almost perfect (Îº = 0.60 â 1.00 for most genotypes, and was almost perfect (Îº = 0.81 â 0.98 for almost all high-risk genotypes. Linear Array overall detected most genotypes more frequently, however this was only statistically significant for HPV51 (EuroArray; p = 0.0497, HPV52 (Anyplex II; p = 0.039 and HPV61 (Anyplex II; p=0.047. EuroArray detected signficantly more HPV26 (p = 0.002 and Anyplex II detected more HPV42 (p = 0.035 than Linear Array. Each assay performed differently for HPV68 detection: EuroArray and LA were in moderate to substantial agreement with Anyplex II (Îº = 0.46 and 0.62, respectively, but were in poor disagreement with each other (Îº = â0.01. Conclusions: EuroArray and Anyplex II had similar sensitivity to Linear Array for most high-risk genotypes, with slightly lower sensitivity for HPV 51 or 52. Keywords: Human papillomavirus, Genotyping, Linear Array, Anyplex II, EuroArray, Cervix
Logistics in smallpox: the legacy.
Wickett, John; Carrasco, Peter
2011-12-30
Logistics, defined as "the time-related positioning of resources" was critical to the implementation of the smallpox eradication strategy of surveillance and containment. Logistical challenges in the smallpox programme included vaccine delivery, supplies, staffing, vehicle maintenance, and financing. Ensuring mobility was essential as health workers had to travel to outbreaks to contain them. Three examples illustrate a range of logistic challenges which required imagination and innovation. Standard price lists were developed to expedite vehicle maintenance and repair in Bihar, India. Innovative staffing ensured an adequate infrastructure for vehicle maintenance in Bangladesh. The use of disaster relief mechanisms in Somalia provided airlifts, vehicles and funding within 27 days of their initiation. In contrast the Expanded Programme on Immunization (EPI) faces more complex logistical challenges. Copyright © 2011 Elsevier Ltd. All rights reserved.
Multiagent Systems in Logistics Environment
Kumara, R
2000-01-01
... the cost added to the price of the products. This is a typical logistics problem. Under some assumptions, this problem can be solved through negotiation in a forum of candidate transportation companies...
Logistics Reduction and Repurposing Project
National Aeronautics and Space Administration — The project enables a largely mission-independent, cradle-to-grave-to-cradle approach to minimize logistics contributions to total mission architecture mass. The...
Case Study on Logistics Performance
Shahryar Sorooshian
2013-05-01
Full Text Available The paper presents research carried out at a medium‐size manufacturing organization in east Asia. The study tries to highlight the importance of supply chain management; specifically, our aim for this study is to understand logistics and performance measurement in the logistics and supply chain, and we include a theoretical discussion of online data collected and a case study of the logistic performance of a real organization. The study also examines the performance of the selected company, identifies the problems and provides recommendations for improvements. This study can be a guide for business advisers and those interested in analysing company performance, especially from a logistics viewpoint. We also suggest the methodology of this case study for those who want to have a better understanding of a business environment before starting their own business, or for benchmarking practice during strategic planning.
Defense Logistics Agency Revenue Eliminations
1996-01-01
The issue of revenue eliminations was identified during our work on the Defense Logistics Agency portion of the Audit of Revenue Accounts in the FY 1996 Financial Statements of the Defense Business Operations Fund...
Joint Logistics, Fact or Fiction?
Carroll, Walton
1998-01-01
...) and the evolution of Joint doctrine to meet these new demands. The focus of this examination remains at the strategic level and the ability of the Services to meet the logistical demands of the modern theater battlefield...
OWI transportation/logistics program
Shappert, L.B.; Joy, D.S.; Heiskell, M.M.; Turner, D.W.
1978-01-01
In development of a comprehensive plan to assure the availability of a transport system by 1985 capable of moving commercial radioactive wastes to federal waste repositories, a series of concerns were identified as having the potential to interfere seriously with the overall objective. These are tabulated and briefly reviewed. Activities to counteract these concerns were formulated. Logistics models were then developed. The spent fuel logistics model is described
INFORMATION SECURITY IN LOGISTICS COOPERATION
Tomasz Małkus
2015-03-01
Full Text Available Cooperation of suppliers of raw materials, semi-finished products, finished products, wholesalers, retailers in the form of the supply chain, as well as outsourcing of specialized logistics service require ensuring adequate support of information. It concerns the use of appropriate computer tools. The security of information in such conditions of collaboration becomes the important problem for parties of contract. The objective of the paper is to characterize main issues relating to security of information in logistics cooperation.
NASA Space Rocket Logistics Challenges
Neeley, James R.; Jones, James V.; Watson, Michael D.; Bramon, Christopher J.; Inman, Sharon K.; Tuttle, Loraine
2014-01-01
The Space Launch System (SLS) is the new NASA heavy lift launch vehicle and is scheduled for its first mission in 2017. The goal of the first mission, which will be uncrewed, is to demonstrate the integrated system performance of the SLS rocket and spacecraft before a crewed flight in 2021. SLS has many of the same logistics challenges as any other large scale program. Common logistics concerns for SLS include integration of discreet programs geographically separated, multiple prime contractors with distinct and different goals, schedule pressures and funding constraints. However, SLS also faces unique challenges. The new program is a confluence of new hardware and heritage, with heritage hardware constituting seventy-five percent of the program. This unique approach to design makes logistics concerns such as commonality especially problematic. Additionally, a very low manifest rate of one flight every four years makes logistics comparatively expensive. That, along with the SLS architecture being developed using a block upgrade evolutionary approach, exacerbates long-range planning for supportability considerations. These common and unique logistics challenges must be clearly identified and tackled to allow SLS to have a successful program. This paper will address the common and unique challenges facing the SLS programs, along with the analysis and decisions the NASA Logistics engineers are making to mitigate the threats posed by each.
Shandiz, Mahdi Heravian; Khalilzadeh, Mohammadmahdi; Anvari, Kazem [Mashhad Branch, Islamic Azad University, Mashhad (Iran, Islamic Republic of); Layen, Ghorban Safaeian [Mashhad University of Medical Science, Mashhad (Iran, Islamic Republic of)
2015-03-15
In order to keep the acceptable level of the radiation oncology linear accelerators, it is necessary to apply a reliable quality assurance (QA) program. The QA protocols, published by authoritative organizations, such as the American Association of Physicists in Medicine (AAPM), determine the quality control (QC) tests which should be performed on the medical linear accelerators and the threshold levels for each test. The purpose of this study is to increase the accuracy and precision of the selected QC tests in order to increase the quality of treatment and also increase the speed of the tests to convince the crowded centers to start a reliable QA program. A new method has been developed for two of the QC tests; optical distance indicator (ODI) QC test as a daily test and gantry angle QC test as a monthly test. This method uses an image processing approach utilizing the snapshots taken by the CCD camera to measure the source to surface distance (SSD) and gantry angle. The new method of ODI QC test has an accuracy of 99.95% with a standard deviation of 0.061 cm and the new method for gantry angle QC has a precision of 0.43 degrees. The automated proposed method which is used for both ODI and gantry angle QC tests, contains highly accurate and precise results which are objective and the human-caused errors have no effect on the results. The results show that they are in the acceptable range for both of the QC tests, according to AAPM task group 142.
Shandiz, Mahdi Heravian; Khalilzadeh, Mohammadmahdi; Anvari, Kazem; Layen, Ghorban Safaeian
2015-01-01
In order to keep the acceptable level of the radiation oncology linear accelerators, it is necessary to apply a reliable quality assurance (QA) program. The QA protocols, published by authoritative organizations, such as the American Association of Physicists in Medicine (AAPM), determine the quality control (QC) tests which should be performed on the medical linear accelerators and the threshold levels for each test. The purpose of this study is to increase the accuracy and precision of the selected QC tests in order to increase the quality of treatment and also increase the speed of the tests to convince the crowded centers to start a reliable QA program. A new method has been developed for two of the QC tests; optical distance indicator (ODI) QC test as a daily test and gantry angle QC test as a monthly test. This method uses an image processing approach utilizing the snapshots taken by the CCD camera to measure the source to surface distance (SSD) and gantry angle. The new method of ODI QC test has an accuracy of 99.95% with a standard deviation of 0.061 cm and the new method for gantry angle QC has a precision of 0.43 degrees. The automated proposed method which is used for both ODI and gantry angle QC tests, contains highly accurate and precise results which are objective and the human-caused errors have no effect on the results. The results show that they are in the acceptable range for both of the QC tests, according to AAPM task group 142.
Chaurasia, Ashok; Harel, Ofer
2015-02-10
Tests for regression coefficients such as global, local, and partial F-tests are common in applied research. In the framework of multiple imputation, there are several papers addressing tests for regression coefficients. However, for simultaneous hypothesis testing, the existing methods are computationally intensive because they involve calculation with vectors and (inversion of) matrices. In this paper, we propose a simple method based on the scalar entity, coefficient of determination, to perform (global, local, and partial) F-tests with multiply imputed data. The proposed method is evaluated using simulated data and applied to suicide prevention data. Copyright © 2014 John Wiley & Sons, Ltd.
A simulation-based goodness-of-fit test for random effects in generalized linear mixed models
Waagepetersen, Rasmus
2006-01-01
The goodness-of-fit of the distribution of random effects in a generalized linear mixed model is assessed using a conditional simulation of the random effects conditional on the observations. Provided that the specified joint model for random effects and observations is correct, the marginal...... distribution of the simulated random effects coincides with the assumed random effects distribution. In practice, the specified model depends on some unknown parameter which is replaced by an estimate. We obtain a correction for this by deriving the asymptotic distribution of the empirical distribution...
A simulation-based goodness-of-fit test for random effects in generalized linear mixed models
Waagepetersen, Rasmus Plenge
The goodness-of-fit of the distribution of random effects in a generalized linear mixed model is assessed using a conditional simulation of the random effects conditional on the observations. Provided that the specified joint model for random effects and observations is correct, the marginal...... distribution of the simulated random effects coincides with the assumed random effects distribution. In practice the specified model depends on some unknown parameter which is replaced by an estimate. We obtain a correction for this by deriving the asymptotic distribution of the empirical distribution function...
Ramdas, Aaditya; Reddi, Sashank J.; Poczos, Barnabas; Singh, Aarti; Wasserman, Larry
2014-01-01
Nonparametric two sample testing deals with the question of consistently deciding if two distributions are different, given samples from both, without making any parametric assumptions about the form of the distributions. The current literature is split into two kinds of tests - those which are consistent without any assumptions about how the distributions may differ (\\textit{general} alternatives), and those which are designed to specifically test easier alternatives, like a difference in me...
Fuerst, R [Industrieanlagen-Betriebsgesellschaft mbH, Magnetbahn-Versuchsanlage, Lathen/Ems (Germany)
1996-12-31
In German high-speed magnetic train technology, iron-clad synchronous long-stator linear motors of levitation stator design are used to propel and brake the vehicles. This paper uses the propulsion design of the Transrapid test facility in Emsland (TVE) to illustrate in practical terms the dimensioning parameters for thrust calculations and their interdependencies. The paper is based on description conventions common for rotating electrical machines and rail technology. (orig.)
Logistics Management: New trends in the Reverse Logistics
Antonyová, A.; Antony, P.; Soewito, B.
2016-04-01
Present level and quality of the environment are directly dependent on our access to natural resources, as well as their sustainability. In particular production activities and phenomena associated with it have a direct impact on the future of our planet. Recycling process, which in large enterprises often becomes an important and integral part of the production program, is usually in small and medium-sized enterprises problematic. We can specify a few factors, which have direct impact on the development and successful application of the effective reverse logistics system. Find the ways to economically acceptable model of reverse logistics, focusing on converting waste materials for renewable energy, is the task in progress.
Challenges of Green Logistics in Southeast Europe
Beškovnik, Bojan; Jakomin, Livio
2010-01-01
This paper describes the trends towards green logistics in global aspect and challenges of adopting green logistics in the region of Southeast Europe. Modern logistics with supply chain management is experiencing a period of important evolution. From reversible logistics, we came to green logistics, which is a wider concept of environmentally friendly thinking. Reverse logistics includes processes of movements and transportation of waste from users to recycling plants; meanwhile, green logist...
Cornall, Alyssa M; Poljak, Marin; Garland, Suzanne M; Phillips, Samuel; Machalek, Dorothy A; Tan, Jeffrey H; Quinn, Michael A; Tabrizi, Sepehr N
2017-12-01
To compare human papillomavirus genotype-specific performance of two genotyping assays, Anyplex II HPV28 (Seegene) and EuroArray HPV (EuroImmun), with Linear Array HPV (Roche). DNA extracted from clinican-collected cervical brush specimens in PreservCyt medium (Hologic), from 403 women undergoing management for detected cytological abnormalities, was tested on the three assays. Genotype-specific agreement were assessed by Cohen's kappa statistic and Fisher's z-test of significance between proportions. Agreement between Linear Array and the other 2 assays was substantial to almost perfect (κ = 0.60 - 1.00) for most genotypes, and was almost perfect (κ = 0.81 - 0.98) for almost all high-risk genotypes. Linear Array overall detected most genotypes more frequently, however this was only statistically significant for HPV51 (EuroArray; p = 0.0497), HPV52 (Anyplex II; p = 0.039) and HPV61 (Anyplex II; p=0.047). EuroArray detected signficantly more HPV26 (p = 0.002) and Anyplex II detected more HPV42 (p = 0.035) than Linear Array. Each assay performed differently for HPV68 detection: EuroArray and LA were in moderate to substantial agreement with Anyplex II (κ = 0.46 and 0.62, respectively), but were in poor disagreement with each other (κ = -0.01). EuroArray and Anyplex II had similar sensitivity to Linear Array for most high-risk genotypes, with slightly lower sensitivity for HPV 51 or 52. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.
FUTURE CIRCULAR COLLIDER LOGISTICS STUDY
Beißert, Ulrike; Kuhlmann, Gerd; Nettsträter, Andreas; Prasse, Christian; Wohlfahrt, Andreas
2018-01-01
The Large Hadron Collider (LHC) at the European Organization for Nuclear Research CERN in Geneva is the largest and most powerful collider in the world. CERN and its research and experimental infrastructure is not only a focus for the science community but is also very much in the public eye. With the Future Circular Collider (FCC) Study, CERN has begun to examine the feasibility of a new underground accelerator ring with a length of approximately 100 kilometres. Logistics is of great importance for the construction, assembly and operation of the FCC. During the planning, construction and assembly of the LHC, logistics proved to be one of the key factors. As the FCC is even larger than the LHC, logistics will also become more and more significant. This report therefore shows new concepts, methods and analytics for logistics, supply chain and transport concepts as part of the FCC study. This report deals with three different logistics aspects for the planning and construction phase of FCC: 1. A discussion of d...
Passaro, Bruno M.; Rodrigues, Laura N. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Videira, Heber S., E-mail: bruno.passaro@gmail.com [Universidade de Sao Paulo (HCFMRP/USP), Sao Paulo, SP (Brazil). Faculdade de Medicina. Hospital das Clinicas
2013-04-15
The aim of this study is to assess and analyze the stability of the calibration factor of three linear accelerators, as well as the other dosimetric parameters normally included in a program of quality control in radiotherapy. The average calibration factors of the accelerators for the period of approximately four years for the Clinac 600C and Clinac 6EX were (0.998±0.012) and (0.996±0.014), respectively. For the Clinac 2100CD 6 MV and 15 MV was (1.008±0.009) and (1.006±0.010), respectively, in a period of approximately four years. The data of the calibration factors were divided into four subgroups for a more detailed analysis of behavior over the years. Through statistical analysis of calibration factors, we found that for the 600C and Clinacs 2100CD, is an expected probability that more than 90% of cases the values are within acceptable ranges according to TG-142, while for the Clinac 6EX is expected around 85% since this had several exchanges of accelerator components. The values of TPR20,10 of three accelerators are practically constant and within acceptable limits according to the TG-142. It can be concluded that a detailed study of data from the calibration factor of the accelerators and TPR{sub 20},{sub 10} from a quantitative point of view, is extremely useful in a quality assurance program. (author)
Dalian Marius DORAN
2017-11-01
Full Text Available The article aims to research impact of budget balance, whether surplus or deficit, on the main indicator characterizing the economic growth of a country, namely GDP and the inflation rate in the 27 European Union Member States and the United Kingdom. For this analysis was used panel data, taking into account the period from 2001 to 2015. The method used for the analysis is the linear regression with fixed effects and with Driscoll-Kraay standard errors. The dependent variables are the growth rate of real GDP and the inflation rate, and the independent variable is the budget balance (surplus or deficit. The results obtained after using econometric software Stata shows a positive impact of budget balance on growth in the European Union for the analyzed period.
Zurkinden, Andrew Stephen; Kramer, Morten; Sichani, Mahdi Teimouri
2012-01-01
and the response of the device for regular and irregular waves were measured. Good correspondence is found between the numerical and the physical model for relatively mild wave conditions. For higher waves the numerical model seems to underestimate the response of the device due to its linear fluidstructure......Currently, a number of wave energy converters are being analyzed by means of numerical models in order to predict the electrical power generation under given wave conditions. A common characteristic of this procedure is to integrate the loadings from the hydrodynamics, power take-off and mooring...... systems into a central wave to wire model. The power production then depends on the control strategy which is applied to the device. The objective of this paper is to develop numerical methods for motion analysis of marine structures with a special emphasis on wave energy converters. Two different time...
Zurkinden, Andrew Stephen; Kramer, Morten; Sichani, Mahdi Teimouri
2012-01-01
systems into a central wave to wire model. The power production then depends on the control strategy which is applied to the device. The objective of this paper is to develop numerical methods for motion analysis of marine structures with a special emphasis on wave energy converters. Two different time...... domain models are applied to a point absorber system working in pitch mode only. The device is similar to the well-known Wavestar prototype located in the Danish North Sea. A laboratory model has been set up in order to validate the numerical simulations of the dynamics. Wave Excitation force...... interaction assumption and linearized equation of motion. The region over which the numerical model is valid will be presented in terms of non-dimensional parameters describing the different wave states....
Shokouhi, Parisa; Rivière, Jacques; Lake, Colton R; Le Bas, Pierre-Yves; Ulrich, T J
2017-11-01
The use of nonlinear acoustic techniques in solids consists in measuring wave distortion arising from compliant features such as cracks, soft intergrain bonds and dislocations. As such, they provide very powerful nondestructive tools to monitor the onset of damage within materials. In particular, a recent technique called dynamic acousto-elasticity testing (DAET) gives unprecedented details on the nonlinear elastic response of materials (classical and non-classical nonlinear features including hysteresis, transient elastic softening and slow relaxation). Here, we provide a comprehensive set of linear and nonlinear acoustic responses on two prismatic concrete specimens; one intact and one pre-compressed to about 70% of its ultimate strength. The two linear techniques used are Ultrasonic Pulse Velocity (UPV) and Resonance Ultrasound Spectroscopy (RUS), while the nonlinear ones include DAET (fast and slow dynamics) as well as Nonlinear Resonance Ultrasound Spectroscopy (NRUS). In addition, the DAET results correspond to a configuration where the (incoherent) coda portion of the ultrasonic record is used to probe the samples, as opposed to a (coherent) first arrival wave in standard DAET tests. We find that the two visually identical specimens are indistinguishable based on parameters measured by linear techniques (UPV and RUS). On the contrary, the extracted nonlinear parameters from NRUS and DAET are consistent and orders of magnitude greater for the damaged specimen than those for the intact one. This compiled set of linear and nonlinear ultrasonic testing data including the most advanced technique (DAET) provides a benchmark comparison for their use in the field of material characterization. Copyright © 2017 Elsevier B.V. All rights reserved.
REGIONAL LOGISTICS CENTER: FORMATION AND FUNCTIONING SPESIFIC
Oleg Tkach
2017-08-01
Full Text Available In this article the essence of the definition of logistics centers is defined, the main provisions concerning the formation of the logistics center are defined. The formation of a logistic hub is analyzed. The structure of the transport-logistic center is proposed. The basic requirements for the location of the regional logistics center and the principles of its operation are determined. The financial and financial mechanism of a typical logistics center and their effective functioning are presented. It is proved that the most important component of the logistics center is transport. Key words: logistics centers, logistics, hub, distribution centers, transport and logistics centers, regional logistic centers, logistics complex, transport, transport-logistic system.
Logistics require savvy negotiation, patience
Talboy, R.G.
1991-01-01
In the Soviet Union, logistics are affected by the extraordinary political, social and physical environment, so that operations are virtually all art, rather than science. Furthermore, this art, as it applies to a particular project, probably does not lend itself to broad generalizations about what would work somewhere else. Each project will have its own idiosyncrasies, depending on its type and location in the vast Soviet republics, and upon the personalities involved. This article discusses only the logistics that worked out and are still evolving for the project with which the author was associated
Logistics background study: underground mining
Hanslovan, J. J.; Visovsky, R. G.
1982-02-01
Logistical functions that are normally associated with US underground coal mining are investigated and analyzed. These functions imply all activities and services that support the producing sections of the mine. The report provides a better understanding of how these functions impact coal production in terms of time, cost, and safety. Major underground logistics activities are analyzed and include: transportation and personnel, supplies and equipment; transportation of coal and rock; electrical distribution and communications systems; water handling; hydraulics; and ventilation systems. Recommended areas for future research are identified and prioritized.
Seasonality and the logistic map
Silva, Emily; Peacock-Lopez, Enrique
2017-01-01
Nonlinear difference equations, such as the logistic map, have been used to study chaos and also to model population dynamics. Here we propose a model that extends the “lose + lose = win” behavior found in Parrondo’s Paradox, where switching between chaotic parameters in the logistic map yields periodic behavior (“chaos + chaos = order”). The model uses twelve parameters each reflecting the conditions of one of the twelve months. In this paper we study the effects of smooth-transitioning parameters and the robust system that emerges.
Chen, R; Hahn, C E W; Farmery, A D
2012-08-15
The development of a methodology for testing the time response, linearity and performance characteristics of ultra fast fibre optic oxygen sensors in the liquid phase is presented. Two standard medical paediatric oxygenators are arranged to provide two independent extracorporeal circuits. Flow from either circuit can be diverted over the sensor under test by means of a system of rapid cross-over solenoid valves exposing the sensor to an abrupt change in oxygen partial pressure, P O2. The system is also capable of testing the oxygen sensor responses to changes in temperature, carbon dioxide partial pressure P CO2 and pH in situ. Results are presented for a miniature fibre optic oxygen sensor constructed in-house with a response time ≈ 50 ms and a commercial fibre optic sensor (Ocean Optics Foxy), when tested in flowing saline and stored blood. Copyright © 2012 Elsevier B.V. All rights reserved.
Gallo, S; Panzeca, S; Longo, A; Altieri, S; Bentivoglio, A; Dondi, D; Marconi, R P; Protti, N; Zeffiro, A; Marrale, M
2015-12-01
This paper reports the preliminary results obtained by Electron Paramagnetic Resonance (EPR) measurements on films of IRGANOX® 1076 phenols with and without low content (5% by weight) of gadolinium oxide (Gd2O3) exposed in the thermal column of the Triga Mark II reactor of LENA (Laboratorio Energia Nucleare Applicata) of Pavia (Italy). Thanks to their size, the phenolic films here presented are good devices for the dosimetry of beams with high dose gradient and which require accurate knowledge of the precise dose delivered. The dependence of EPR signal as function of neutron dose was investigated in the fluence range between 10(11) cm(-2) and 10(14) cm(-2). Linearity of EPR response was found and the signal was compared with that of commercial alanine films. Our analysis showed that gadolinium oxide (5% by weight) can enhance the thermal neutron sensitivity more than 18 times. Irradiated dosimetric films of phenolic compound exhibited EPR signal fading of about 4% after 10 days from irradiation. Copyright © 2015 Elsevier Ltd. All rights reserved.
Mattei, G.; Ahluwalia, A.
2018-04-01
We introduce a new function, the apparent elastic modulus strain-rate spectrum, E_{app} ( \\dot{ɛ} ), for the derivation of lumped parameter constants for Generalized Maxwell (GM) linear viscoelastic models from stress-strain data obtained at various compressive strain rates ( \\dot{ɛ}). The E_{app} ( \\dot{ɛ} ) function was derived using the tangent modulus function obtained from the GM model stress-strain response to a constant \\dot{ɛ} input. Material viscoelastic parameters can be rapidly derived by fitting experimental E_{app} data obtained at different strain rates to the E_{app} ( \\dot{ɛ} ) function. This single-curve fitting returns similar viscoelastic constants as the original epsilon dot method based on a multi-curve global fitting procedure with shared parameters. Its low computational cost permits quick and robust identification of viscoelastic constants even when a large number of strain rates or replicates per strain rate are considered. This method is particularly suited for the analysis of bulk compression and nano-indentation data of soft (bio)materials.
Non-linear beam dynamics tests in the LHC: LHC dynamic aperture MD on Beam 2 (24th of June 2012)
Maclean, E H; Persson, T H B; Redaelli, S; Schmidt, F; Tomas, R; Uythoven, J
2013-01-01
This MD note summarizes measurements performed on LHC Beam 2 during the non-linear machine development (MD) of 24 June 2012. The aim of the measurement was to observe the dynamic aperture of LHC Beam 2, and obtain turn-by-turn (TbT) betatron oscillation data, enabling the study of amplitude detuning and resonance driving terms (RDTs). The regular injections required by the MD also represented an opportunity to test a new coupling feedback routine based on the analysis of injection oscillation data. Initial measurements were performed on the nominal state of the LHC at injection. On completion of this study the Landau octupoles were turned off and corrections for higher-order chromaticities were implemented to reduce the non-linearity of the machine as far as possible. A second set of measurements were then performed. All studies were performed using the LHC aperture kicker (MKA).
Logistics Dynamics and Demographic Change
Klumpp, Matthias; Abidi, Hella; Bioly, Sascha; Buchkremer, Rüdiger; Ebener, Stefan; Sandhaus, Gregor; Freitag, Michael; Kotzab, Herbert; Pannek, Jürgen
2016-01-01
Change and dynamics in logistics are interestingly driven at the same time by external as well as internal forces. This contribution outlines a big data literature review methodology to overview recognizable external changes and analyzes the interaction of one major trend—demographic change—further
CONCEPTUAL ISSUES REGARDING REVERSE LOGISTICS
Ioana Olariu
2013-12-01
Full Text Available As the power of consumers is growing, the product return for customer service and customer retention has become a common practice in the competitive market, which propels the recent practice of reverse logistics in companies. Many firms attracted by the value available in the flow, have proactively participated in handling returned products at the end of their usefulness or from other parts of the product life cycle. Reverse logistics is the flow and management of products, packaging, components and information from the point of consumption to the point of origin. It is a collection of practices similar to those of supply chain management, but in the opposite direction, from downstream to upstream. It involves activities such as reuse, repair, remanufacture, refurbish, reclaim and recycle. For the conventional forward logistics systems, the flow starts upstream as raw materials, later as manufactured parts and components to be assembled and continues downstream to reach customers as final products to be disposed once they reach their economic or useful lives. In reverse logistics, the disposed products are pushed upstream to be repaired, remanufactured, refurbished, and disassembled into components to be reused or as raw material to be recycled for later use.
A Framework for Reverse Logistics
M.P. de Brito (Marisa); R. Dekker (Rommert)
2003-01-01
textabstractReverse Logistics has been stretching out worldwide, involving all the layers of supply chains in various industry sectors. While some actors in the chain have been forced to take products back, others have pro-actively done so, attracted by the value in used products One way or the
Logistic regression for dichotomized counts.
Preisser, John S; Das, Kalyan; Benecha, Habtamu; Stamm, John W
2016-12-01
Sometimes there is interest in a dichotomized outcome indicating whether a count variable is positive or zero. Under this scenario, the application of ordinary logistic regression may result in efficiency loss, which is quantifiable under an assumed model for the counts. In such situations, a shared-parameter hurdle model is investigated for more efficient estimation of regression parameters relating to overall effects of covariates on the dichotomous outcome, while handling count data with many zeroes. One model part provides a logistic regression containing marginal log odds ratio effects of primary interest, while an ancillary model part describes the mean count of a Poisson or negative binomial process in terms of nuisance regression parameters. Asymptotic efficiency of the logistic model parameter estimators of the two-part models is evaluated with respect to ordinary logistic regression. Simulations are used to assess the properties of the models with respect to power and Type I error, the latter investigated under both misspecified and correctly specified models. The methods are applied to data from a randomized clinical trial of three toothpaste formulations to prevent incident dental caries in a large population of Scottish schoolchildren. © The Author(s) 2014.
Quantitative Models for Reverse Logistics
M. Fleischmann (Moritz)
2000-01-01
markdownabstractEconomic, marketing, and legislative considerations are increasingly leading companies to take back and recover their products after use. From a logistics perspective, these initiatives give rise to new goods flows from the user back to the producer. The management of these goods
Woody biomass logistics [Chapter 14
Robert Keefe; Nathaniel Anderson; John Hogland; Ken Muhlenfeld
2014-01-01
The economics of using woody biomass as a fuel or feedstock for bioenergy applications is often driven by logistical considerations. Depending on the source of the woody biomass, the acquisition cost of the material is often quite low, sometimes near zero. However, the cost of harvesting, collection, processing, storage, and transportation from the harvest site to end...
Ion DIMA
2017-03-01
Full Text Available This article aims to provide a quick methodology to determine the critical values of the forces, displacements and stress function of frequency, under a combined linear static (101 Solution - Linear Static and dynamic load in frequency response (108 Solution - Frequency Response, Direct Method, applied to a micro launcher engine test bench, using NASTRAN 400 Solution - Implicit Nonlinear. NASTRAN/PATRAN software is used. Practically in PATRAN the preprocessor has to define a linear or nonlinear static load at step 1 and a dynamic in frequency response load (time dependent at step 2. In Analyze the following options are chosen: for Solution Type Implicit Nonlinear Solution (SOL 400 is selected, for Subcases Static Load and Transient Dynamic is chosen and for Subcase Select the two cases static and dynamic will be selected. NASTRAN solver will overlap results from static analysis with the dynamic analysis. The running time will be reduced three times if using Krylov solver. NASTRAN SYSTEM (387 = -1 instruction is used in order to activate Krylov option. Also, in Analysis the OP2 Output Format shall be selected, meaning that in bdf NASTRAN input file the PARAM POST 1 instruction shall be written. The structural damping can be defined in two different ways: either at the material card or using the PARAM, G, 0.05 instruction (in this example a damping coefficient by 5% was used. The SDAMPING instruction in pair with TABDMP1 work only for dynamic in frequency response, modal method, or in direct method with viscoelastic material, not for dynamic in frequency response, direct method (DFREQ, with linear elastic material. The Direct method – DFREQ used in this example is more accurate. A set in translation of boundary conditions was used and defined at the base of the test bench.
Tanwiwat Jaikuna
2017-02-01
Full Text Available Purpose: To develop an in-house software program that is able to calculate and generate the biological dose distribution and biological dose volume histogram by physical dose conversion using the linear-quadratic-linear (LQL model. Material and methods : The Isobio software was developed using MATLAB version 2014b to calculate and generate the biological dose distribution and biological dose volume histograms. The physical dose from each voxel in treatment planning was extracted through Computational Environment for Radiotherapy Research (CERR, and the accuracy was verified by the differentiation between the dose volume histogram from CERR and the treatment planning system. An equivalent dose in 2 Gy fraction (EQD2 was calculated using biological effective dose (BED based on the LQL model. The software calculation and the manual calculation were compared for EQD2 verification with pair t-test statistical analysis using IBM SPSS Statistics version 22 (64-bit. Results: Two and three-dimensional biological dose distribution and biological dose volume histogram were displayed correctly by the Isobio software. Different physical doses were found between CERR and treatment planning system (TPS in Oncentra, with 3.33% in high-risk clinical target volume (HR-CTV determined by D90%, 0.56% in the bladder, 1.74% in the rectum when determined by D2cc, and less than 1% in Pinnacle. The difference in the EQD2 between the software calculation and the manual calculation was not significantly different with 0.00% at p-values 0.820, 0.095, and 0.593 for external beam radiation therapy (EBRT and 0.240, 0.320, and 0.849 for brachytherapy (BT in HR-CTV, bladder, and rectum, respectively. Conclusions : The Isobio software is a feasible tool to generate the biological dose distribution and biological dose volume histogram for treatment plan evaluation in both EBRT and BT.
SELECTED PROBLEMS OF REVERSE LOGISTICS IN POLAND
Agata Mesjasz-Lech
2009-01-01
This paper presents the essence of reverse logistics and directions of physical and information flows between logistic network partners. It also analyses effects of implementation of the principles of reverse logistics in Poland in the years 2004-2007
Suwono.
1978-01-01
A linear gate providing a variable gate duration from 0,40μsec to 4μsec was developed. The electronic circuity consists of a linear circuit and an enable circuit. The input signal can be either unipolar or bipolar. If the input signal is bipolar, the negative portion will be filtered. The operation of the linear gate is controlled by the application of a positive enable pulse. (author)
Andersen, Per Kragh; Klein, John P.; Rosthøj, Susanne
2003-01-01
Generalised estimating equation; Generalised linear model; Jackknife pseudo-value; Logistic regression; Markov Model; Multi-state model......Generalised estimating equation; Generalised linear model; Jackknife pseudo-value; Logistic regression; Markov Model; Multi-state model...
Mikulich-Gilbertson, Susan K; Wagner, Brandie D; Grunwald, Gary K; Riggs, Paula D; Zerbe, Gary O
2018-01-01
Medical research is often designed to investigate changes in a collection of response variables that are measured repeatedly on the same subjects. The multivariate generalized linear mixed model (MGLMM) can be used to evaluate random coefficient associations (e.g. simple correlations, partial regression coefficients) among outcomes that may be non-normal and differently distributed by specifying a multivariate normal distribution for their random effects and then evaluating the latent relationship between them. Empirical Bayes predictors are readily available for each subject from any mixed model and are observable and hence, plotable. Here, we evaluate whether second-stage association analyses of empirical Bayes predictors from a MGLMM, provide a good approximation and visual representation of these latent association analyses using medical examples and simulations. Additionally, we compare these results with association analyses of empirical Bayes predictors generated from separate mixed models for each outcome, a procedure that could circumvent computational problems that arise when the dimension of the joint covariance matrix of random effects is large and prohibits estimation of latent associations. As has been shown in other analytic contexts, the p-values for all second-stage coefficients that were determined by naively assuming normality of empirical Bayes predictors provide a good approximation to p-values determined via permutation analysis. Analyzing outcomes that are interrelated with separate models in the first stage and then associating the resulting empirical Bayes predictors in a second stage results in different mean and covariance parameter estimates from the maximum likelihood estimates generated by a MGLMM. The potential for erroneous inference from using results from these separate models increases as the magnitude of the association among the outcomes increases. Thus if computable, scatterplots of the conditionally independent empirical Bayes
Vretenar, M
2014-01-01
The main features of radio-frequency linear accelerators are introduced, reviewing the different types of accelerating structures and presenting the main characteristics aspects of linac beam dynamics
Romanov, A. [Fermilab
2016-10-09
Many modern and most future accelerators rely on precise configuration of lattice and trajectory. The Integrable Optics Test Accelerator (IOTA) at Fermilab that is coming to final stages of construction will be used to test advanced approaches of control over particles dynamics. Various experiments planned at IOTA require high flexibility of lattice configuration as well as high precision of lattice and closed orbit control. Dense element placement does not allow to have ideal configuration of diagnostics and correctors for all planned experiments. To overcome this limitations advanced method of lattice an beneficial for other machines. Developed algorithm is based on LOCO approach, extended with various sets of other experimental data, such as dispersion, BPM BPM phase advances, beam shape information from synchrotron light monitors, responses of closed orbit bumps to variations of focusing elements and other. Extensive modeling of corrections for a big number of random seed errors is used to illustrate benefits from developed approach.
Linearization Method and Linear Complexity
Tanaka, Hidema
We focus on the relationship between the linearization method and linear complexity and show that the linearization method is another effective technique for calculating linear complexity. We analyze its effectiveness by comparing with the logic circuit method. We compare the relevant conditions and necessary computational cost with those of the Berlekamp-Massey algorithm and the Games-Chan algorithm. The significant property of a linearization method is that it needs no output sequence from a pseudo-random number generator (PRNG) because it calculates linear complexity using the algebraic expression of its algorithm. When a PRNG has n [bit] stages (registers or internal states), the necessary computational cost is smaller than O(2n). On the other hand, the Berlekamp-Massey algorithm needs O(N2) where N(≅2n) denotes period. Since existing methods calculate using the output sequence, an initial value of PRNG influences a resultant value of linear complexity. Therefore, a linear complexity is generally given as an estimate value. On the other hand, a linearization method calculates from an algorithm of PRNG, it can determine the lower bound of linear complexity.
Crisis Management- Operational Logistics & Asset Visibility Technologies
Braunbeck, Richard A; Mastria, Michael F
2006-01-01
The purpose of this MBA Project was to identify and explore logistical frameworks that leverage technology to overcome problems associated with coordinated logistics operations during crisis management...
Logistics Support of Naval Expeditionary Units
Nilsen, Jan
2004-01-01
.... Based on literature from strategic management, logistics, and supply chain management, the research evaluates the existing theater logistics capabilities and the requirements of the supported expeditionary units...
Osemlak, Paweł
2011-01-01
1. Determination of the size of testes and epididymes on the right and left side, in healthy boys in various age groups with use of non-invasive ultrasound examination method and the method of external linear measurements. 2. Determination of age, when intensive growth of testicular and epididymal size starts. 3. Determination whether there are statistically significant differences between the size of the right and the left testis, as well as between the right and left epididymis. 4. Evaluation of the ultrasound method and method of external linear measurements in their use for scientific investigations. 309 boys, aged from 1 day to 17 years of life, treated in the Clinical Department of Paediatric Surgery and Traumatology of the Medical University in Lublin from 2009 to 2010 due to diseases needed to be treated surgically, but not the scrotum, were examined in this study. No pathologies influencing the development of genital organs were found in these boys. Dimension of the testes was studied with ultrasound method and with method of external linear measurements. Dimension of epididymes was only examined with ultrasound method. In every age group the author calculated mean arithmetical values for: testiscular length, thickness, width and volume, as well as epididymal depth and basis. With consideration of standard deviation (X+/-1 SD) it was possible to define the range of dimension of healthy testes and epididymes and their change with age. Final dimensions of the right and left testis as well as of the right and left epididymis were compared. Dimensions of the testis on the same side of body acquired with the ultrasound method and acquired with the method of external linear measurements were compared. Statistical work-up with Wilcoxon test for two dependent groups was implemented. Ultrasound evaluation pointed to intensive 2.5-times increase in testicular length and width, and 2-times increase in testicular thickness in boys aged 10 to 17 years. Mean volume of
Grelick, A. E.; Arnold, N.; Berg, S.; Dohan, D.; Goeppner, G.; Kang, Y. W.; Nassiri, A.; Pasky, S.; Pile, G.; Smith, T.; Stein, S. J.
2000-01-01
An S-band linear accelerator is the source of particles and the front end of the Advanced Photon Source injector. In addition, it supports a low-energy undulator test line (LEUTL) and drives a free-electron laser (FEL). A waveguide-switching and distribution system is now under construction. The system configuration was revised to be consistent with the recent change to electron-only operation. There are now six modulator-klystron subsystems, two of which are being configured to act as hot sp...
Johansen, Søren; Juselius, Katarina; Frydman, Roman
2010-01-01
This paper discusses the I(2) model with breaks in the deterministic component and illustrates with an analysis of German and US prices, exchange rates, and interest rates in 1975--1999. It provides new results on the likelihood ratio test of overidentifying restrictions on the cointegrating...... relations when they contain piecewise linear trends. One important aim of the paper is to demonstrate that a structured I(2) analysis is useful for a better understanding of the empirical regularities underlying the persistent swings in nominal exchange rates, typical in periods of floating exchange rates....
Valeria Boscaino
2017-01-01
Full Text Available In this paper, we propose a reliability-oriented design of a linear generator-based prototype of a wave energy conversion (WEC, useful for the production of hydrogen in a sheltered water area like Mediterranean Sea. The hydrogen production has been confirmed by a lot of experimental testing and simulations. The system design is aimed to enhance the robustness and reliability and is based on an analysis of the main WEC failures reported in literature. The results of this analysis led to some improvements that are applied to a WEC system prototype for hydrogen production and storage. The proposed WEC system includes the electrical linear generator, the power conversion system, and a sea-water electrolyzer. A modular architecture is conceived to provide ease of extension of the power capability of the marine plant. The experimental results developed on the permanent magnet linear electric generator have allowed identification of the stator winding typology and, consequently, ability to size the power electronics system. The produced hydrogen has supplied a low-power fuel cell stack directly connected to the hydrogen output from the electrolyzer. The small-scale prototype is designed to be installed, in the near future, into the Mediterranean Sea. As shown by experimental and simulation results, the small-scale prototype is suitable for hydrogen production and storage from sea water in this area.
Said-Houari, Belkacem
2017-01-01
This self-contained, clearly written textbook on linear algebra is easily accessible for students. It begins with the simple linear equation and generalizes several notions from this equation for the system of linear equations and introduces the main ideas using matrices. It then offers a detailed chapter on determinants and introduces the main ideas with detailed proofs. The third chapter introduces the Euclidean spaces using very simple geometric ideas and discusses various major inequalities and identities. These ideas offer a solid basis for understanding general Hilbert spaces in functional analysis. The following two chapters address general vector spaces, including some rigorous proofs to all the main results, and linear transformation: areas that are ignored or are poorly explained in many textbooks. Chapter 6 introduces the idea of matrices using linear transformation, which is easier to understand than the usual theory of matrices approach. The final two chapters are more advanced, introducing t...
Empirical Study of E-logistics System Based on Tibet Logistics Industry
Liu, Yu
2013-01-01
With the rapid growth of E-logistics in the global logistics industry, it is important to get insight into E-logistics system in Chinese logistics industry. Regarding the current situation of E-logistics of Chinese logistics industry, there are still many problems to be concerned and resolved. This paper will review the concepts and theoretical background of E-logistics System from previous researches. After acknowledging the essential issues on E-logistics System, a research model is designe...
Transport spatial model for the definition of green routes for city logistics centers
Pamučar, Dragan; Gigović, Ljubomir; Ćirović, Goran; Regodić, Miodrag
2016-01-01
This paper presents a transport spatial decision support model (TSDSM) for carrying out the optimization of green routes for city logistics centers. The TSDSM model is based on the integration of the multi-criteria method of Weighted Linear Combination (WLC) and the modified Dijkstra algorithm within a geographic information system (GIS). The GIS is used for processing spatial data. The proposed model makes it possible to plan routes for green vehicles and maximize the positive effects on the environment, which can be seen in the reduction of harmful gas emissions and an increase in the air quality in highly populated areas. The scheduling of delivery vehicles is given as a problem of optimization in terms of the parameters of: the environment, health, use of space and logistics operating costs. Each of these input parameters was thoroughly examined and broken down in the GIS into criteria which further describe them. The model presented here takes into account the fact that logistics operators have a limited number of environmentally friendly (green) vehicles available. The TSDSM was tested on a network of roads with 127 links for the delivery of goods from the city logistics center to the user. The model supports any number of available environmentally friendly or environmentally unfriendly vehicles consistent with the size of the network and the transportation requirements. - Highlights: • Model for routing light delivery vehicles in urban areas. • Optimization of green routes for city logistics centers. • The proposed model maximizes the positive effects on the environment. • The model was tested on a real network.
Transport spatial model for the definition of green routes for city logistics centers
Pamučar, Dragan, E-mail: dpamucar@gmail.com [University of Defence in Belgrade, Department of Logistics, Pavla Jurisica Sturma 33, 11000 Belgrade (Serbia); Gigović, Ljubomir, E-mail: gigoviclj@gmail.com [University of Defence in Belgrade, Department of Mathematics, Pavla Jurisica Sturma 33, 11000 Belgrade (Serbia); Ćirović, Goran, E-mail: cirovic@sezampro.rs [College of Civil Engineering and Geodesy, The Belgrade University, Hajduk Stankova 2, 11000 Belgrade (Serbia); Regodić, Miodrag, E-mail: mregodic62@gmail.com [University of Defence in Belgrade, Department of Mathematics, Pavla Jurisica Sturma 33, 11000 Belgrade (Serbia)
2016-01-15
This paper presents a transport spatial decision support model (TSDSM) for carrying out the optimization of green routes for city logistics centers. The TSDSM model is based on the integration of the multi-criteria method of Weighted Linear Combination (WLC) and the modified Dijkstra algorithm within a geographic information system (GIS). The GIS is used for processing spatial data. The proposed model makes it possible to plan routes for green vehicles and maximize the positive effects on the environment, which can be seen in the reduction of harmful gas emissions and an increase in the air quality in highly populated areas. The scheduling of delivery vehicles is given as a problem of optimization in terms of the parameters of: the environment, health, use of space and logistics operating costs. Each of these input parameters was thoroughly examined and broken down in the GIS into criteria which further describe them. The model presented here takes into account the fact that logistics operators have a limited number of environmentally friendly (green) vehicles available. The TSDSM was tested on a network of roads with 127 links for the delivery of goods from the city logistics center to the user. The model supports any number of available environmentally friendly or environmentally unfriendly vehicles consistent with the size of the network and the transportation requirements. - Highlights: • Model for routing light delivery vehicles in urban areas. • Optimization of green routes for city logistics centers. • The proposed model maximizes the positive effects on the environment. • The model was tested on a real network.
Framework to Scope Logistics Initiatives
Joubert, JW
2005-07-01
Full Text Available m a t i o n Road Rail Air Water Pipeline N e t w o r k i n f r a s t r u c t u r e T r a n s p o r t v e h i c l e s a n d v e s s e l s N o d e i n f r a s t r u c t u r e... Phy sical freight m o ve m ent Physical freight m o v em e nt freight logistics sector O p e r a t i o n a l h u m a n r e s o u r c e s Origin Destination C o m m o d i t i e s Logistics enablers...
Mobile Robots for Hospital Logistics
Özkil, Ali Gürcan
services to maintain the quality of healthcare provided. Logistics is the most resource demanding service in a hospital. The scale of the transportation tasks is huge and the material flow in a hospital is comparable to that of a factory. We believe that these transportation tasks, to a great extent, can...... be and will be automated using mobile robots. This talk consequently addresses the key technical issues of implementing service robots in hospitals. In simple terms, a robotic system for automating hospital logistics has to be reliable, adaptable and scalable. Robots have to be semi-autonomous, and should reliably...... navigate in large and dynamic environments in the hospital. The complexity of the problem has to be manageable, and the solutions have to be flexible, so that the system can be applicable in real world settings. This talk summarizes the efforts to address these issues. Upon the analysis...
Technology in health care logistics
Jørgensen, Pelle; Wallin, Michael
In most of the developed countries hospitals are facing a major challenge – they have to provide more health care using the same resources. Due to the demographic trend and the increasing share of the population being in a more health-demanding age, the hospitals will have to deal with more...... patients in the future. It is therefore essential that the hospitals are more efficient in order to meet the requirement of providing more health for the same or less resources. Studies have shown that more than 30% of hospital expenditures are related to various logistics cost, making the logistics...... papers presented at scientific conferences, and three articles submitted to scientific journals. In addition to the results, the thesis presents a detailed description of the scientific approach taken, as well as considerations in relation to the scientific approach and the achieved results....
Monte, Luigi
2013-01-01
The present work describes the application of a non-linear Leslie model for predicting the effects of ionising radiation on wild populations. The model assumes that, for protracted chronic irradiation, the effect-dose relationship is linear. In particular, the effects of radiation are modelled by relating the increase in the mortality rates of the individuals to the dose rates through a proportionality factor C. The model was tested using independent data and information from a series of experiments that were aimed at assessing the response to radiation of wild populations of meadow voles and whose results were described in the international literature. The comparison of the model results with the data selected from the above mentioned experiments showed that the model overestimated the detrimental effects of radiation on the size of irradiated populations when the values of C were within the range derived from the median lethal dose (L 50 ) for small mammals. The described non-linear model suggests that the non-expressed biotic potential of the species whose growth is limited by processes of environmental resistance, such as the competition among the individuals of the same or of different species for the exploitation of the available resources, can be a factor that determines a more effective response of population to the radiation effects. -- Highlights: • A model to assess the radiation effects on wild population is described. • The model is based on non-linear Leslie matrix. • The model is applied to small mammals living in an irradiated meadow. • Model output is conservative if effect-dose factor estimated from L 50 is used. • Systemic response to stress of populations in competitive conditions may be more effective
High gradient RF test results of S-band and C-band cavities for medical linear accelerators
Degiovanni, A.; Bonomi, R.; Garlasché, M.; Verdú-Andrés, S.; Wegner, R.; Amaldi, U.
2018-05-01
TERA Foundation has proposed and designed hadrontherapy facilities based on novel linacs, i.e. high gradient linacs which accelerate either protons or light ions. The overall length of the linac, and therefore its cost, is almost inversely proportional to the average accelerating gradient. With the scope of studying the limiting factors for high gradient operation and to optimize the linac design, TERA, in collaboration with the CLIC Structure Development Group, has conducted a series of high gradient experiments. The main goals were to study the high gradient behavior and to evaluate the maximum gradient reached in 3 and 5.7 GHz structures to direct the design of medical accelerators based on high gradient linacs. This paper summarizes the results of the high power tests of 3.0 and 5.7 GHz single-cell cavities.
Activities and Education in Logistics
Jasmina Pašagić Škrinjar
2008-03-01
Full Text Available Logistic approach to traffic means new business policy,economy and ownership, new internal organization, externaland internal communication, different corporate cultures, humanresources management using scientific methods, trainingand education, changed management type and awarding system,knowledge of information technology, communicationskills, electronic commerce, etc. Education is part of all theseelements. The introduction of logistics in all the business activitieshas been imposed due to the following reasons: because ofthe life-cycle shortening of the product and its delivery, becauseof sudden technological development, because of productionand market globalization, because of the increase in competitiveness.This paper describes first various logistic activities with theindication of practical and scientific approaches. The logisticsapproach in the traffic activities requires upgrading of the professionaland scientific level to a higher one which means additionaltraining and acquiring of new skills as well as new technologiesfor the employees.The basic aim of research was to specifY the basic logisticsactivities and problems in order to indicate the need of differentforms of education. Fast technological and social changes requireconstant improvement and modification of professionalknowledge and acqui1ing of new scientific methods and skills.
Dritz, K.; Absil-Mills, M.; Jacobs, K.
2002-01-01
This document is the Software Test Plan/Description/Report (STP/STD/STR) for the DII COE Enhanced Logistics Intratheater Support Tool (ELIST) mission application. It combines in one document the information normally presented separately in a Software Test Plan, a Software Test Description, and a Software Test Report; it also presents this information in one place for all the segments of the ELIST mission application. The primary purpose of this document is to show that ELIST has been tested by the developer and found, by that testing, to install, deinstall, and work properly. The information presented here is detailed enough to allow the reader to repeat the testing independently. The remainder of this document is organized as follows. Section 1.1 identifies the ELIST mission application. Section 2 is the list of all documents referenced in this document. Section 3, the Software Test Plan, outlines the testing methodology and scope-the latter by way of a concise summary of the tests performed. Section 4 presents detailed descriptions of the tests, along with the expected and observed results; that section therefore combines the information normally found in a Software Test Description and a Software Test Report. The remaining small sections present supplementary information. Throughout this document, the phrase ELIST IP refers to the Installation Procedures (IP) for the Enhanced Logistics Intratheater Support Tool (ELIST) Global Data Segment, Database Instance Segment, Database Fill Segment, Database Segment, Database Utility Segment, Software Segment, and Reference Data Segment
E. Adli
2011-08-01
Full Text Available We discuss X-band rf power production and deceleration in the two-beam test stand of the CLIC test facility at CERN. The rf power is extracted from an electron drive beam by a specially designed power extraction structure. In order to test the structures at high-power levels, part of the generated power is recirculated to an input port, thus allowing for increased deceleration and power levels within the structure. The degree of recirculation is controlled by a splitter and phase shifter. We present a model that describes the system and validate it with measurements over a wide range of parameters. Moreover, by correlating rf power measurements with the energy lost by the electron beam, as measured in a spectrometer placed after the power extraction structure, we are able to identify system parameters, including the form factor of the electron beam. The quality of the agreement between model and reality gives us confidence to extrapolate the results found in the present test facility towards the parameter regime of CLIC.
Adli, E; Dubrovskiy, A; Syratchev, I; Ruber, R; Ziemann, V
2011-01-01
We discuss X-band rf power production and deceleration in the two-beam test stand of the CLIC test facility at CERN. The rf power is extracted from an electron drive beam by a specially designed power extraction structure. In order to test the structures at high-power levels, part of the generated power is recirculated to an input port, thus allowing for increased deceleration and power levels within the structure. The degree of recirculation is controlled by a splitter and phase shifter. We present a model that describes the system and validate it with measurements over a wide range of parameters. Moreover, by correlating rf power measurements with the energy lost by the electron beam, as measured in a spectrometer placed after the power extraction structure, we are able to identify system parameters, including the form factor of the electron beam. The quality of the agreement between model and reality gives us confidence to extrapolate the results found in the present test facility towards the parameter reg...
Pivi, M
2008-01-01
Beam instability caused by the electron cloud has been observed in positron and proton storage rings, and it is expected to be a limiting factor in the performance of future colliders [1-3]. The effect is expected to be particularly severe in magnetic field regions. To test possible mitigation methods in magnetic fields, we have installed a new 4-dipole chicane experiment in the PEP-II Low Energy Ring (LER) at SLAC with both bare and TiN-coated aluminum chambers. In particular, we have observed a large variation of the electron flux at the chamber wall as a function of the chicane dipole field. We infer this is a new high order resonance effect where the energy gained by the electrons in the positron beam depends on the phase of the electron cyclotron motion with respect to the bunch crossing, leading to a modulation of the secondary electron production. Presumably the cloud density is modulated as well and this resonance effect could be used to reduce its magnitude in future colliders. We present the experimental results obtained during January 2008 until the April final shut-down of the PEP-II machine
Wiedermann, Wolfgang; Li, Xintong
2018-04-16
In nonexperimental data, at least three possible explanations exist for the association of two variables x and y: (1) x is the cause of y, (2) y is the cause of x, or (3) an unmeasured confounder is present. Statistical tests that identify which of the three explanatory models fits best would be a useful adjunct to the use of theory alone. The present article introduces one such statistical method, direction dependence analysis (DDA), which assesses the relative plausibility of the three explanatory models on the basis of higher-moment information about the variables (i.e., skewness and kurtosis). DDA involves the evaluation of three properties of the data: (1) the observed distributions of the variables, (2) the residual distributions of the competing models, and (3) the independence properties of the predictors and residuals of the competing models. When the observed variables are nonnormally distributed, we show that DDA components can be used to uniquely identify each explanatory model. Statistical inference methods for model selection are presented, and macros to implement DDA in SPSS are provided. An empirical example is given to illustrate the approach. Conceptual and empirical considerations are discussed for best-practice applications in psychological data, and sample size recommendations based on previous simulation studies are provided.
Stoll, R R
1968-01-01
Linear Algebra is intended to be used as a text for a one-semester course in linear algebra at the undergraduate level. The treatment of the subject will be both useful to students of mathematics and those interested primarily in applications of the theory. The major prerequisite for mastering the material is the readiness of the student to reason abstractly. Specifically, this calls for an understanding of the fact that axioms are assumptions and that theorems are logical consequences of one or more axioms. Familiarity with calculus and linear differential equations is required for understand
Key Trends Shaping the Global Logistics Environment
Handfield, Robert; Straube, Frank; Pfohl, Hans-Christian
A summary from the full study “Trends and Strategies in Logistics and Supply Chain Management. Embracing Global Logistics Complexity to Drive Market Advantage” (2013).......A summary from the full study “Trends and Strategies in Logistics and Supply Chain Management. Embracing Global Logistics Complexity to Drive Market Advantage” (2013)....
THEORETICAL FRAMES FOR DESIGNING REVERSE LOGISTICS PROCESSES
Janusz K. Grabara; Sebastian Kot
2009-01-01
Logistics processes of return flow became more and more important in present business practice. Because of better customer satisfaction, environmental and financial aspects many enterprises deal with reverse logistics performance. The paper is a literature review focused on the design principles of reverse logistics processes Keywords: reverse logistics, designing.
Subset selection from generalized logistic populations
Laan, van der M.J.; Laan, van der P.
1997-01-01
We give an introduction to the logistic and generalized logistic distributions. These generalized logistic distributions Type-I, Type-II and Type-III are indexed by a real valued parameter. They have been derived as mixtures with the standard logistic distribution and for discrete values of the
LOGISTICS MANAGEMENT IN THE CONTEMPORARY ECONOMY
Ion SARBU
2014-03-01
Full Text Available The evolution of logistics management as a system in the recent decades can be characterized by the influence of the globalization processes and the economic integration in the European Union. Systemic logistic approach ensured revolutionizing the optimization of the logistics chain. Logistics management must be given to permanent forms of the new legal and organizational structure appropriate to the contemporary economy.
LOGISTICS MANAGEMENT IN THE CONTEMPORARY ECONOMY
Ion SARBU
2014-01-01
Full Text Available The evolution of logistics management as a system in the recent decades can be characterized by the influence of the globalization processes and the economic integration in the European Union. Systemic logistic approach ensured revolutionizing the optimization of the logistics chain. Logistics management must be given to permanent forms of the new legal and organizational structure appropriate to the contemporary economy.
Cohen, B.L.
1987-01-01
The University of Pittsburgh Radon Project for large scale measurements of radon concentrations in homes is described. Its principal research is to test the linear-no threshold dose-response relationship for radiation carcinogenesis by determining average radon levels in the 25 U.S. counties (within certain population ranges) with highest and lowest lung cancer rates. The theory predicts that the former should have about 3 times higher average radon levels than the latter, under the assumption that any correlation between exposure to radon and exposure to other causes of lung cancer is weak. The validity of this assumption is tested with data on average radon level vs replies to items on questionnaires; there is little correlation between radon levels in houses and smoking habits, educational attainment, or economic status of the occupants, or with urban vs rural environs which is an indicator of exposure to air pollution
Wareing, J.; Bretherton, I.
This paper presents preliminary results from the programme for hold period tests on a cast BQ of type 316 stainless steel at 570 deg. C. The results of tensile hold period tests on a relatively low ductility cast of type 316 stainless steel have indicated that the failure mechanism changes from a creep-fatigue interaction failure to a creep dominated failure at low strain levels. An assessment of the linear damage summation approach for failure prediction indicates that it is inappropriate for creep-fatigue interaction failures. For creep dominated fracture, failure occurs when the accumulation relaxation strain exhausts the material ductility i.e. Nsub(f epsilon R)=D. The failure criterion based on a creep summation in terms of time to fracture underestimates life
Baba, Toshimi; Gotoh, Yusaku; Yamaguchi, Satoshi; Nakagawa, Satoshi; Abe, Hayato; Masuda, Yutaka; Kawahara, Takayoshi
2017-08-01
This study aimed to evaluate a validation reliability of single-step genomic best linear unbiased prediction (ssGBLUP) with a multiple-lactation random regression test-day model and investigate an effect of adding genotyped cows on the reliability. Two data sets for test-day records from the first three lactations were used: full data from February 1975 to December 2015 (60 850 534 records from 2 853 810 cows) and reduced data cut off in 2011 (53 091 066 records from 2 502 307 cows). We used marker genotypes of 4480 bulls and 608 cows. Genomic enhanced breeding values (GEBV) of 305-day milk yield in all the lactations were estimated for at least 535 young bulls using two marker data sets: bull genotypes only and both bulls and cows genotypes. The realized reliability (R 2 ) from linear regression analysis was used as an indicator of validation reliability. Using only genotyped bulls, R 2 was ranged from 0.41 to 0.46 and it was always higher than parent averages. The very similar R 2 were observed when genotyped cows were added. An application of ssGBLUP to a multiple-lactation random regression model is feasible and adding a limited number of genotyped cows has no significant effect on reliability of GEBV for genotyped bulls. © 2016 Japanese Society of Animal Science.
Wiedemann, H.
1981-11-01
Since no linear colliders have been built yet it is difficult to know at what energy the linear cost scaling of linear colliders drops below the quadratic scaling of storage rings. There is, however, no doubt that a linear collider facility for a center of mass energy above say 500 GeV is significantly cheaper than an equivalent storage ring. In order to make the linear collider principle feasible at very high energies a number of problems have to be solved. There are two kinds of problems: one which is related to the feasibility of the principle and the other kind of problems is associated with minimizing the cost of constructing and operating such a facility. This lecture series describes the problems and possible solutions. Since the real test of a principle requires the construction of a prototype I will in the last chapter describe the SLC project at the Stanford Linear Accelerator Center.
Wiedemann, H.
1981-11-01
Since no linear colliders have been built yet it is difficult to know at what energy the linear cost scaling of linear colliders drops below the quadratic scaling of storage rings. There is, however, no doubt that a linear collider facility for a center of mass energy above say 500 GeV is significantly cheaper than an equivalent storage ring. In order to make the linear collider principle feasible at very high energies a number of problems have to be solved. There are two kinds of problems: one which is related to the feasibility of the principle and the other kind of problems is associated with minimizing the cost of constructing and operating such a facility. This lecture series describes the problems and possible solutions. Since the real test of a principle requires the construction of a prototype I will in the last chapter describe the SLC project at the Stanford Linear Accelerator Center
Solow, Daniel
2014-01-01
This text covers the basic theory and computation for a first course in linear programming, including substantial material on mathematical proof techniques and sophisticated computation methods. Includes Appendix on using Excel. 1984 edition.
Liesen, Jörg
2015-01-01
This self-contained textbook takes a matrix-oriented approach to linear algebra and presents a complete theory, including all details and proofs, culminating in the Jordan canonical form and its proof. Throughout the development, the applicability of the results is highlighted. Additionally, the book presents special topics from applied linear algebra including matrix functions, the singular value decomposition, the Kronecker product and linear matrix equations. The matrix-oriented approach to linear algebra leads to a better intuition and a deeper understanding of the abstract concepts, and therefore simplifies their use in real world applications. Some of these applications are presented in detailed examples. In several ‘MATLAB-Minutes’ students can comprehend the concepts and results using computational experiments. Necessary basics for the use of MATLAB are presented in a short introduction. Students can also actively work with the material and practice their mathematical skills in more than 300 exerc...
Berberian, Sterling K
2014-01-01
Introductory treatment covers basic theory of vector spaces and linear maps - dimension, determinants, eigenvalues, and eigenvectors - plus more advanced topics such as the study of canonical forms for matrices. 1992 edition.
Searle, Shayle R
2012-01-01
This 1971 classic on linear models is once again available--as a Wiley Classics Library Edition. It features material that can be understood by any statistician who understands matrix algebra and basic statistical methods.
Christofilos, N.C.; Polk, I.J.
1959-02-17
Improvements in linear particle accelerators are described. A drift tube system for a linear ion accelerator reduces gap capacity between adjacent drift tube ends. This is accomplished by reducing the ratio of the diameter of the drift tube to the diameter of the resonant cavity. Concentration of magnetic field intensity at the longitudinal midpoint of the external sunface of each drift tube is reduced by increasing the external drift tube diameter at the longitudinal center region.
Marketing in the business activity of logistics service providers
Marcin Świtała
2013-09-01
Full Text Available Background: This article is a discussion on the role of marketing in the activity of logistics service providers. The strong competition and changing purchasing preferences should motivate the transport, forwarding and logistics sector managers to apply the marketing approach in practice. Methods: Results of direct research, conducted among a targeted group of 100 companies from the transport, forwarding and logistics sector, constitute the source basis. The sample group was divided into three categories of logistics providers: 2PL, 3PL and 4PL. The statistical analysis was based on three different non-parametric tests (Kruskal-Wallis, Chi-square and V Kramer. Results and conclusions: Currently, marketing does not play a key role in the activity of logistics services providers. The prevailing opinion is that importance of marketing in the company is average. The respondents have assessed in a similar way their activity compared to the activities of the competition. However, it was found that with the increase of the level of specialization (2PL-4PL, the awareness of impact of marketing on the logistics services sector also increased. The logistics services providers, who offer a wide range of logistics services, asses their competitive position in a better light.
Rakovska Miroslava
2016-10-01
Full Text Available The increased demand and supply of logistics services bring together the logistics service providers (LSPs and the companies that outsource logistics activities. LSPs stand in between those companies and their customers, thus playing an essential role for supply chain integration. If the two parties have different viewpoints of the processes in the supply chain, the fulfillment of the goal to satisfy the end customers may be hindered. The purpose of this article is two-fold: First, to investigate the characteristics of logistics outsourcing in Bulgaria from the perspectives of the logistics service providers and their customers, and more specifically, to compare their viewpoints concerning the motives for outsourcing, the methods and contents of communication and some relationship management aspects; Second, to assess the relations of the communication and relationship management aspects to customer satisfaction. This article is based on empirical data provided by 138 manufacturing and trading companies and 136 LSPs and collected through two structured questionnaires designed to address the researched issues. The data were analyzed using descriptive statistics and the independent samples t-test. The research found that the service related reasons for logistics outsourcing are prevailing and that LSPs overestimate, compared to manufacturing and trading companies, motives related to service, organizational capabilities and relationships, while more manufacturing and trading companies concern as important the availability of logistics assets and the provision of value-added services. The research also found that both the LSPs and their customers consider that the extent of sharing of knowledge and information essential for material flow integration is very low and that the usage of team meetings and joint teams is quite rare. Also, customers do not view their relationships with the LSPs as so collaborative as viewed by the LSPs. Furthermore, the
The Art and Science of Defense Logistics
1995-04-01
The Art And Science Of Defense Logistics CSC 1995 SUBJECT AREA - Logistics THE ART AND SCIENCE OF DEFENSE LOGISTICS...Government EXECUTIVE SUMMARY Title: The Art and Science of Defense Logistics Author: Major S. I. Schuler, USMC Research Questions: 1...00-1995 4. TITLE AND SUBTITLE The Art And Science Of Defense Logistics 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6
COSTS FOR IMPLEMENTING LOGISTICS INTO THE COMPANY
Mariana Man; Maria Nowicka-Skowron
2010-01-01
The ways of approaching the logistic problems need the use of some varied techniques and means, and the elaboration of a logistic project – which would aim the entire company – mobilises multiple personnel for a period of a few months and claims the intervention of logisticians within the logistic consultancy office, whom shall also act after putting the logistic project into practice. The accomplishment of any logistic wide change within the company needs an array of activities that may be g...
A Theoretic Model of Transport Logistics Demand
Natalija Jolić; Nikolina Brnjac; Ivica Oreb
2006-01-01
Concerning transport logistics as relation between transportand integrated approaches to logistics, some transport and logisticsspecialists consider the tenn tautological. However,transport is one of the components of logistics, along with inventories,resources, warehousing, infonnation and goods handling.Transport logistics considers wider commercial and operationalframeworks within which the flow of goods is plannedand managed. The demand for transport logistics services canbe valorised as ...
Robust mislabel logistic regression without modeling mislabel probabilities.
Hung, Hung; Jou, Zhi-Yu; Huang, Su-Yun
2018-03-01
Logistic regression is among the most widely used statistical methods for linear discriminant analysis. In many applications, we only observe possibly mislabeled responses. Fitting a conventional logistic regression can then lead to biased estimation. One common resolution is to fit a mislabel logistic regression model, which takes into consideration of mislabeled responses. Another common method is to adopt a robust M-estimation by down-weighting suspected instances. In this work, we propose a new robust mislabel logistic regression based on γ-divergence. Our proposal possesses two advantageous features: (1) It does not need to model the mislabel probabilities. (2) The minimum γ-divergence estimation leads to a weighted estimating equation without the need to include any bias correction term, that is, it is automatically bias-corrected. These features make the proposed γ-logistic regression more robust in model fitting and more intuitive for model interpretation through a simple weighting scheme. Our method is also easy to implement, and two types of algorithms are included. Simulation studies and the Pima data application are presented to demonstrate the performance of γ-logistic regression. © 2017, The International Biometric Society.
Mobile Robots for Hospital Logistics
Özkil, Ali Gürcan
2012-01-01
Hospitals are complex and dynamic organisms that are vital to the well-being of societies. Providing good quality healthcare is the ultimate goal of a hospital, and it is what most of us are only concerned with. A hospital, on the other hand, has to orchestrate a great deal of supplementary services to maintain the quality of healthcare provided. Logistics is the most resource demanding service in a hospital. The scale of the transportation tasks is huge and the material flow in a hospital is...
Evaluating the Logistical Service in a Hybrid System of Marketing
Mônica Vivianne Teixeira Rosa
2016-09-01
Full Text Available The hybrid system of marketing, also referred to as multi-channel, has become an effective strategy of maintaining and expanding markets. However, the success of a new market channel is guided in its ability to provide an effective logistics services. The objective of this study was to identify how the logistical service provided by a new multi-channel distributor is assessed from the perspective of marketing channel agents. It is used an analytical model with dimensions of quality logistics services based on literature. For the analysis of the survey were conducted tests based on statistical inference, as T-Student test, Wilcoxon and Mann-Whitney-Wilcoxon (MWW. Evaluation results showed favorable rates as the logistics service provided by multi-channel and also indicated good levels in the quality of logistics services present in the production chain investigated. However, some dimensions of logistics services surveyed reported rates likely to improvements such as ease of procedures and post-delivery support. It was concluded that the strategy to diversify marketing channels provides strategic resource for organizations, providing opportunities for increased market share, brand consolidation, greater market coverage, logistic skills and differentiation from competitors.
Larson, Nicholas B; McDonnell, Shannon; Cannon Albright, Lisa; Teerlink, Craig; Stanford, Janet; Ostrander, Elaine A; Isaacs, William B; Xu, Jianfeng; Cooney, Kathleen A; Lange, Ethan; Schleutker, Johanna; Carpten, John D; Powell, Isaac; Bailey-Wilson, Joan E; Cussenot, Olivier; Cancel-Tassin, Geraldine; Giles, Graham G; MacInnis, Robert J; Maier, Christiane; Whittemore, Alice S; Hsieh, Chih-Lin; Wiklund, Fredrik; Catalona, William J; Foulkes, William; Mandal, Diptasri; Eeles, Rosalind; Kote-Jarai, Zsofia; Ackerman, Michael J; Olson, Timothy M; Klein, Christopher J; Thibodeau, Stephen N; Schaid, Daniel J
2017-05-01
Next-generation sequencing technologies have afforded unprecedented characterization of low-frequency and rare genetic variation. Due to low power for single-variant testing, aggregative methods are commonly used to combine observed rare variation within a single gene. Causal variation may also aggregate across multiple genes within relevant biomolecular pathways. Kernel-machine regression and adaptive testing methods for aggregative rare-variant association testing have been demonstrated to be powerful approaches for pathway-level analysis, although these methods tend to be computationally intensive at high-variant dimensionality and require access to complete data. An additional analytical issue in scans of large pathway definition sets is multiple testing correction. Gene set definitions may exhibit substantial genic overlap, and the impact of the resultant correlation in test statistics on Type I error rate control for large agnostic gene set scans has not been fully explored. Herein, we first outline a statistical strategy for aggregative rare-variant analysis using component gene-level linear kernel score test summary statistics as well as derive simple estimators of the effective number of tests for family-wise error rate control. We then conduct extensive simulation studies to characterize the behavior of our approach relative to direct application of kernel and adaptive methods under a variety of conditions. We also apply our method to two case-control studies, respectively, evaluating rare variation in hereditary prostate cancer and schizophrenia. Finally, we provide open-source R code for public use to facilitate easy application of our methods to existing rare-variant analysis results. © 2017 WILEY PERIODICALS, INC.
Bruyndonckx, Robin; Aerts, Marc; Hens, Niel
2016-09-01
In a linear multilevel model, significance of all fixed effects can be determined using F tests under maximum likelihood (ML) or restricted maximum likelihood (REML). In this paper, we demonstrate that in the presence of primary unit sparseness, the performance of the F test under both REML and ML is rather poor. Using simulations based on the structure of a data example on ceftriaxone consumption in hospitalized children, we studied variability, type I error rate and power in scenarios with a varying number of secondary units within the primary units. In general, the variability in the estimates for the effect of the primary unit decreased as the number of secondary units increased. In the presence of singletons (i.e., only one secondary unit within a primary unit), REML consistently outperformed ML, although even under REML the performance of the F test was found inadequate. When modeling the primary unit as a random effect, the power was lower while the type I error rate was unstable. The options of dropping, regrouping, or splitting the singletons could solve either the problem of a high type I error rate or a low power, while worsening the other. The permutation test appeared to be a valid alternative as it outperformed the F test, especially under REML. We conclude that in the presence of singletons, one should be careful in using the F test to determine the significance of the fixed effects, and propose the permutation test (under REML) as an alternative. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Transport logistics in pollen tubes.
Chebli, Youssef; Kroeger, Jens; Geitmann, Anja
2013-07-01
Cellular organelles move within the cellular volume and the effect of the resulting drag forces on the liquid causes bulk movement in the cytosol. The movement of both organelles and cytosol leads to an overall motion pattern called cytoplasmic streaming or cyclosis. This streaming enables the active and passive transport of molecules and organelles between cellular compartments. Furthermore, the fusion and budding of vesicles with and from the plasma membrane (exo/endocytosis) allow for transport of material between the inside and the outside of the cell. In the pollen tube, cytoplasmic streaming and exo/endocytosis are very active and fulfill several different functions. In this review, we focus on the logistics of intracellular motion and transport processes as well as their biophysical underpinnings. We discuss various modeling attempts that have been performed to understand both long-distance shuttling and short-distance targeting of organelles. We show how the combination of mechanical and mathematical modeling with cell biological approaches has contributed to our understanding of intracellular transport logistics.
3PL, 4PL and insourcing logistics
Mauro Vivaldini
2015-12-01
Full Text Available Logistics services have evolved and changed over time, especially in the hiring of them according to the concepts of 3PL (third party logistics, 4PL (fourth party logistics or insourcing logistics. 3PL service is a consolidated business, 4PL is an option for outsourcing logistics and has already been adopted by some organizations, and insourcing logistics suggests the return of these activities being internalized by companies, which is still a relatively unexplored subject in logistics literature. Analyzing these themes in the literature, this study updates the view on them and proposes a conceptual framework that classifies the different models of logistics services, showing the different options that can be adopted to help the company decide how to run their logistics services.
Alcaraz, J.
2001-01-01
After several years of study e''+ e''- linear colliders in the TeV range have emerged as the major and optimal high-energy physics projects for the post-LHC era. These notes summarize the present status form the main accelerator and detector features to their physics potential. The LHC era. These notes summarize the present status, from the main accelerator and detector features to their physics potential. The LHC is expected to provide first discoveries in the new energy domain, whereas an e''+ e''- linear collider in the 500 GeV-1 TeV will be able to complement it to an unprecedented level of precision in any possible areas: Higgs, signals beyond the SM and electroweak measurements. It is evident that the Linear Collider program will constitute a major step in the understanding of the nature of the new physics beyond the Standard Model. (Author) 22 refs
Expeditionary Logistics: How the Marine Corps Supports Its Expeditionary Operations
2015-06-01
Asset Planning at the Lowest Level .................60 5. Improve Field Testing of All New Data Systems .............................60 C...Figure 7. The Levels of Logistic Support. (from MCDP 4, 1997) ..................................21 Figure 8. Case Study Methodology (Yin, 2009, p. 1...Combat Support System–Marine Corps GCE Ground Combat Element JOPES Joint Operational Planning and Execution System LCE Logistics Combat Element MAGTF
Possibilities of the common research-development action in the field of automated logistical engines
Pap Lajos
2003-12-01
Full Text Available The paper briefly presents the R&D cooperation of the Department of Materials Handling and Logistics and Departments of Automation. The main fields of cooperation are introduced. Different kind of Linear Motor (hereafter LM drives are being developed and tested for warehouse and rolling conveyor systems. Modern control strategies using AI methods are being investigated and tested for Automated guide vehicle. Wireless communication methods are being searched and developed for mobile material handling devices. Application possibilities of voice recognition and image processing are being tested for control of material handling robots and devices. Application of process visualization programs are being developed and investigated. Multi-level industrial communication system is being developed for the laboratories of the cooperating departments.
Outsourcing of Logistics Activities in Manufacturing Industry
Anton Ogorelc
2012-10-01
Full Text Available The external supply of logistics se1vices is part of a trend towardoutsourcing non-core logistics activities. The scope ofthird-party logistics may range from a relatively limited combinationof activities (e.g. transportation and warehousing to acomprehensive set of logistics se1vices.The authors first discuss the characteristics of business logisticsin manufacturing indusfly, to be taken into account inlogistics outsourcing. They particularly point out the motimtionsfor logistics outsourcing, the possibilities of outsourcing,as well as supplier selection. Finally they analyze the outsourcingin the reverse logistics.
Combining or Separating Forward and Reverse Logistics
Herbert-Hansen, Zaza Nadja Lee; Larsen, Samuel; Nielsen, Anders
2018-01-01
Purpose – While forward logistics handles and manages the flow of goods downstream in the supply chain from suppliers to customers, reverse logistics (RL) manages the flow of returned goods upstream. A firm can combine reverse logistics with forward logistics, keep the flows separated, or choose......-research addresses intra-RL issues while the relationship between forward and reverse logistics is under-researched. This paper contributes to RL-theory by identifying the contextual factors that determine the most advantageous relationship between forward and reverse logistics, and proposes a novel decision making...
Logistics, electronic commerce, and the environment
Sarkis, Joseph; Meade, Laura; Talluri, Srinivas
2002-02-01
Organizations realize that a strong supporting logistics or electronic logistics (e-logistics) function is important from both commercial and consumer perspectives. The implications of e-logistics models and practices cover the forward and reverse logistics functions of organizations. They also have direct and profound impact on the natural environment. This paper will focus on a discussion of forward and reverse e-logistics and their relationship to the natural environment. After discussion of the many pertinent issues in these areas, directions of practice and implications for study and research are then described.
Maria Åström
2012-06-01
Full Text Available The possible effects of different organisations of the science curriculum in schools participating in PISA 2003 are tested with a hierarchical linear model (HLM of two levels. The analysis is based on science results. Swedish schools are free to choose how they organise the science curriculum. They may choose to work subject-specifically (with Biology, Chemistry and Physics, integrated (with Science or to mix these two. In this study, all three ways of organising science classes in compulsory school are present to some degree. None of the different ways of organising science education displayed statistically significant better student results in scientific literacy as measured in PISA 2003. The HLM model used variables of gender, country of birth, home language, preschool attendance, an economic, social and cultural index as well as the teaching organisation.
Schwantes-An, Tae-Hwi; Sung, Heejong; Sabourin, Jeremy A; Justice, Cristina M; Sorant, Alexa J M; Wilson, Alexander F
2016-01-01
In this study, the effects of (a) the minor allele frequency of the single nucleotide variant (SNV), (b) the degree of departure from normality of the trait, and (c) the position of the SNVs on type I error rates were investigated in the Genetic Analysis Workshop (GAW) 19 whole exome sequence data. To test the distribution of the type I error rate, 5 simulated traits were considered: standard normal and gamma distributed traits; 2 transformed versions of the gamma trait (log 10 and rank-based inverse normal transformations); and trait Q1 provided by GAW 19. Each trait was tested with 313,340 SNVs. Tests of association were performed with simple linear regression and average type I error rates were determined for minor allele frequency classes. Rare SNVs (minor allele frequency < 0.05) showed inflated type I error rates for non-normally distributed traits that increased as the minor allele frequency decreased. The inflation of average type I error rates increased as the significance threshold decreased. Normally distributed traits did not show inflated type I error rates with respect to the minor allele frequency for rare SNVs. There was no consistent effect of transformation on the uniformity of the distribution of the location of SNVs with a type I error.
Sommariva, C.; Nardon, E.; Beyer, P.; Hoelzl, M.; Huijsmans, G. T. A.; van Vugt, D.; Contributors, JET
2018-01-01
In order to contribute to the understanding of runaway electron generation mechanisms during tokamak disruptions, a test particle tracker is introduced in the JOREK 3D non-linear MHD code, able to compute both full and guiding center relativistic orbits. Tests of the module show good conservation of the invariants of motion and consistency between full orbit and guiding center solutions. A first application is presented where test electron confinement properties are investigated in a massive gas injection-triggered disruption simulation in JET-like geometry. It is found that electron populations initialised before the thermal quench (TQ) are typically not fully deconfined in spite of the global stochasticity of the magnetic field during the TQ. The fraction of ‘survivors’ decreases from a few tens down to a few tenths of percent as the electron energy varies from 1 keV to 10 MeV. The underlying mechanism for electron ‘survival’ is the prompt reformation of closed magnetic surfaces at the plasma core and, to a smaller extent, the subsequent reappearance of a magnetic surface at the edge. It is also found that electrons are less deconfined at 10 MeV than at 1 MeV, which appears consistent with a phase averaging effect due to orbit shifts at high energy.
Logistics in hospitals: a case study of some Singapore hospitals.
Pan, Zhi Xiong; Pokharel, Shaligram
2007-01-01
The purpose of this paper is to investigate logistics activities in Singapore hospitals. It defines various types of activities handled by a logistics division. Inventory management policy and the use of information and communication technologies (ICT) for logistics purposes are also discussed. The study identifies the nature of strategic alliances in Singapore's health care industry. This study was conducted by utilizing a framework for data collection, pre-testing the questionnaire and conducting interviews. Various relevant literature was reviewed to design the questionnaire. This study finds that logistics division carry out many related activities and some of them also provide engineering services. The hospitals make use of ICT. The hospitals are clustered under various groups to minimize the cost of operation, including the logistics related costs. However, hospitals do not see alliances with suppliers as a strategic option; rather they focus on outsourcing of logistics services. The findings also show that Singapore hospitals have a good stocking policy for both medical and non-medical items so that changes in patient mix can be easily handled. Singapore is continuously improving its health care industry and therefore, the findings will help hospitals in other regions to adopt some of the practices, like concentrating on local vendors, outsourcing, clustering, and maximum use of information technology as competitive factors that can improve the service and reduce the cost of operation. The paper suggests motivators and barriers to the use of ICT in logistics in the health care industry.
Focused Logistics: Time for Functional Command
Mintzlaff, Jeffrey G
2005-01-01
.... Unfortunately, logistical support is often taken for granted. As a result, the U.S. Military's logistical system has become sluggish, often unreliable, and expensive, in part due to its fragmented and inefficient organizational structure. The U.S...
Logistic Vehicle System Replacement Cost Estimate
Stinson, Margaret
1998-01-01
The Logistics Vehicle System (LVS) was originally fielded from 1985-1989. Most of the LVS fleet will reach end-of-service life in 2005, therefore the goal of the Logistics Vehicle System Replacement (LVSR...
Comparing the Discrete and Continuous Logistic Models
Gordon, Sheldon P.
2008-01-01
The solutions of the discrete logistic growth model based on a difference equation and the continuous logistic growth model based on a differential equation are compared and contrasted. The investigation is conducted using a dynamic interactive spreadsheet. (Contains 5 figures.)
The Multinational Logistics Joint Task Force (MLJTF)
Higginbotham, Matthew T
2007-01-01
In this monograph, by analyzing the UN, NATO and the US Army's evolving Modular Logistics Doctrine, the author integrates the key areas from each doctrine into a multinational logistics joint task force (MLJTF) organization...
Barkman, W.E.; Adams, W.Q.; Berrier, B.R.
1978-01-01
A linear induction motor has been operated on a test bed with a feedback pulse resolution of 5 nm (0.2 μin). Slewing tests with this slide drive have shown positioning errors less than or equal to 33 nm (1.3 μin) at feedrates between 0 and 25.4 mm/min (0-1 ipm). A 0.86-m (34-in)-stroke linear motor is being investigated, using the SPACO machine as a test bed. Initial results were encouraging, and work is continuing to optimize the servosystem compensation
Research on 6R Military Logistics Network
Jie, Wan; Wen, Wang
The building of military logistics network is an important issue for the construction of new forces. This paper has thrown out a concept model of 6R military logistics network model based on JIT. Then we conceive of axis spoke y logistics centers network, flexible 6R organizational network, lean 6R military information network based grid. And then the strategy and proposal for the construction of the three sub networks of 6Rmilitary logistics network are given.
A FRAMEWORK FOR STRUCTURING CITY LOGISTICS INITIATIVES
Snežana Tadić; Slobodan Zečević
2016-01-01
Interest in the problems and conceptual solutions for city logistics is increasing each year. City is the place of largest concentration of economic and social activities, and logistics is very important for the sustainability and the economy of the city. Numerous research projects indicate that the state of urban logistics is quite critical. City logistics system is extremely complex, with a large number of participants with different roles, problems, interests and goals. They all want an at...
Logistics Sourcing Strategies in Supply Chain Design
Liu, Liwen
2007-01-01
A company's logistics sourcing strategy determines whether it structures and organizeslogistics within the company or company group or integrates logistics upstream and downstreamin the supply chain. First, three different types of logistics sourcing strategies in supply chaindesign are described and the theoretical background for the development of these strategies,including both transaction cost theory and network theory, is analyzed. Two special casesabout logistics sourcing strategy decis...
A hybrid solution approach for a multi-objective closed-loop logistics network under uncertainty
Mehrbod, Mehrdad; Tu, Nan; Miao, Lixin
2015-06-01
The design of closed-loop logistics (forward and reverse logistics) has attracted growing attention with the stringent pressures of customer expectations, environmental concerns and economic factors. This paper considers a multi-product, multi-period and multi-objective closed-loop logistics network model with regard to facility expansion as a facility location-allocation problem, which more closely approximates real-world conditions. A multi-objective mixed integer nonlinear programming formulation is linearized by defining new variables and adding new constraints to the model. By considering the aforementioned model under uncertainty, this paper develops a hybrid solution approach by combining an interactive fuzzy goal programming approach and robust counterpart optimization based on three well-known robust counterpart optimization formulations. Finally, this paper compares the results of the three formulations using different test scenarios and parameter-sensitive analysis in terms of the quality of the final solution, CPU time, the level of conservatism, the degree of closeness to the ideal solution, the degree of balance involved in developing a compromise solution, and satisfaction degree.
An integrated logistic formula for prediction of complications from radiosurgery
Flickinger, J.C.
1989-01-01
An integrated logistic model for predicting the probability of complications when small volumes of tissue receive an inhomogeneous radiation dose is described. This model can be used with either an exponential or linear quadratic correction for dose per fraction and time. Both the exponential and linear quadratic versions of this integrated logistic formula provide reasonable estimates of the tolerance of brain to radiosurgical dose distributions where there are small volumes of brain receiving high radiation doses and larger volumes receiving lower doses. This makes it possible to predict the probability of complications from stereotactic radiosurgery, as well as combinations of fractionated large volume irradiation with a radiosurgical boost. Complication probabilities predicted for single fraction radiosurgery with the Leksell Gamma Unit using 4, 8, 14, and 18 mm diameter collimators as well as for whole brain irradiation combined with a radiosurgical boost are presented. The exponential and linear quadratic versions of the integrated logistic formula provide useful methods of calculating the probability of complications from radiosurgical treatment
Dobec, Marinko; Bannwart, Fridolin; Kaeppeli, Franz; Cassinotti, Pascal
2009-05-01
There is a need for reliable, automated high throughput HPV detection and genotyping methods for pre- and post-prophylactic vaccine intervention analyses. To optimize the linear array (LA) HPV genotyping test (Roche Diagnostics, Rotkreuz) in regard to possible automation steps for the routine laboratory diagnosis of HPV infections and to analyze the HPV genotype distribution in cervical specimens of women without cytological abnormalities in Switzerland. 680 cervical cell specimens with normal cytology, obtained from women undergoing routine cervical screening by liquid-based Pap smear, were analyzed by the LA HPV genotyping test for HPV-DNA. The automation of the LA HPV genotyping test resulted in a total hands-on time reduction of 255 min (from 480 to 225 min; 53%). Any of 37 HPV genotypes were detected in 117 (17.2%) and high-risk (HR) HPV in 55 (8.1%) of 680 women with normal cytology. The highest prevalence of any HPV (28.1%) and HR-HPV (15.1%) was observed in age-group 21-30 and showed a continuous decrease in older age-groups. The most common HR-HPV genotypes were HPV-16 (12%), HPV-31 (9.4%), HPV-52 (6%), HPV-51 (5.1%), HPV-45 (4.3%), HPV-58 (4.3%) and HPV-59 (4.3%). The optimization and automation of the LA HPV genotyping test makes it suited for high throughput HPV detection and typing. The epidemiological data provides information about distribution of HPV genotypes in women without cytological abnormalities in Switzerland and may be important for determining the future impact of vaccines and potential changes in the country's epidemiological HPV profile.
Analysis of Unmanned Systems in Military Logistics
2016-12-01
performance measures: customer satisfaction , flexibility, visibility, and trust. If we apply this explanation of Li and Schulze (2011) to the military...unmanned systems, initially, we aimed to define current and proposed unmanned applications in civilian-sector logistics and current military...aimed to define current and proposed unmanned applications in civilian-sector logistics and current military logistics challenges. Then, justifying
Logistics hardware and services control system
Koromilas, A.; Miller, K.; Lamb, T.
1973-01-01
Software system permits onsite direct control of logistics operations, which include spare parts, initial installation, tool control, and repairable parts status and control, through all facets of operations. System integrates logistics actions and controls receipts, issues, loans, repairs, fabrications, and modifications and assets in predicting and allocating logistics parts and services effectively.
Logistics potentials in business competitive advantage creation
Rafał Matwiejczuk
2013-12-01
Full Text Available Background: Companies constantly search for ways to achieve and sustain long-term competitive advantage. Among the factors influencing the competitive advantage creation there are so called logistics potentials, which constitute a component part of a business strategic potentials. Logistics resources, logistics capabilities and logistics competences are the main components of the logistics potentials structure and hierarchy. Methods: In order to recognize the logistics potentials which determine the competitive advantage creation one may use the assumptions and elements of contemporary management concepts, including strategic management. In particular the article deals with Resource-Based View (RBV, Dynamic Capabilities Concept (DCC and - first of all - Competence-Based Management (CBM. Results and conclusions: Several significant research projects have presented a wide scope and a large number of possibilities of logistics potentials (and logistics competences in particular influence on business competitive advantage creation. The article briefly presents the research results conducted by: (1 Michigan State University (USA, (2 European Logistics Association (ELA in cooperation with A.T. Kearney, (3 Computer Sciences Corporation and (4 Capgemini. The research results have pointed out to differentiated but at the same distinctive symptoms of logistics competences influence on competitive advantage creation. The article also refers to the results of the research carried out by the Chair of Logistics & Marketing at Opole University (Poland in companies operating in Poland. The research has been mainly dealing with the significance of logistics competences in competitive advantage creation.
Karloff, Howard
1991-01-01
To this reviewer’s knowledge, this is the first book accessible to the upper division undergraduate or beginning graduate student that surveys linear programming from the Simplex Method…via the Ellipsoid algorithm to Karmarkar’s algorithm. Moreover, its point of view is algorithmic and thus it provides both a history and a case history of work in complexity theory. The presentation is admirable; Karloff's style is informal (even humorous at times) without sacrificing anything necessary for understanding. Diagrams (including horizontal brackets that group terms) aid in providing clarity. The end-of-chapter notes are helpful...Recommended highly for acquisition, since it is not only a textbook, but can also be used for independent reading and study. —Choice Reviews The reader will be well served by reading the monograph from cover to cover. The author succeeds in providing a concise, readable, understandable introduction to modern linear programming. —Mathematics of Computing This is a textbook intend...
Multipurpose Cargo Transfer Bags fro Reducing Exploration Mission Logistics
Baccus, Shelley; Broyan, James Lee, Jr.; Borrego, Melissa
2016-01-01
The Logistics Reduction (LR) project within the Advanced Exploration Systems (AES) division is tasked with reducing logistical mass and repurposing logistical items. Multipurpose Cargo Transfer Bags (MCTB) have been designed such that they can serve the same purpose as a Cargo Transfer Bag (CTB), the common logistics carrying bag for the International Space Station (ISS). After use as a cargo carrier, a regular CTB becomes trash, whereas the MCTB can be unfolded into a flat panel for reuse. Concepts and potential benefits for various MCTB applications will be discussed including partitions, crew quarters, solar radiation storm shelters, acoustic blankets, and forward osmosis water processing. Acoustic MCTBs are currently in use on ISS to reduce the noise generated by the T2 treadmill, which reaches the hazard limit at high speeds. The development of the AMCTB included identification of keep out zones, acoustic properties, deployment considerations, and structural testing. Features developed for these considerations are applicable to MCTBs for all crew outfitting applications.
Reducing Mission Logistics with Multipurpose Cargo Transfer Bags
Baccus, Shelley; Broyan, James Lee, Jr.; Borrego, Melissa
2016-01-01
The Logistics Reduction (LR) project within Advanced Exploration Systems (AES) is tasked with reducing logistical mass and repurposing logistical items. Multipurpose Cargo Transfer Bags (MCTB) have been designed such that they can serve the same purpose as a Cargo Transfer Bag (CTB), the common logistics carrying bag for the International Space Station (ISS). After use as a cargo carrier, a regular CTB becomes trash, whereas the MCTB can be unfolded into a flat panel for reuse. Concepts and potential benefits for various MCTB applications will be discussed including partitions, crew quarters, solar radiation storm shelters, acoustic blankets, and forward osmosis water processing. Acoustic MCTBs are currently in use on ISS to reduce the noise generated by the T2 treadmill, which reaches the hazard limit at high speeds. The development of the AMCTB included identification of keep-out zones, acoustic properties, deployment considerations, and structural testing. Features developed for these considerations are applicable to MCTBs for all crew outfitting applications.
Gómez, F.J., E-mail: javier.gomez@amsimulation.com [Advanced Material Simulation, AMS, Bilbao (Spain); Martin Rengel, M.A., E-mail: mamartin.rengel@upm.es [E.T.S.I. Caminos, Canales y Puertos, Universidad Politécnica de Madrid, C/Professor Aranguren SN, E-28040 Madrid (Spain); Ruiz-Hervias, J.; Puerta, M.A. [E.T.S.I. Caminos, Canales y Puertos, Universidad Politécnica de Madrid, C/Professor Aranguren SN, E-28040 Madrid (Spain)
2017-06-15
In this work, the hoop fracture toughness of ZIRLO{sup ®} fuel cladding is calculated as a function of three parameters: hydrogen concentration, temperature and displacement rate. To this end, pre-hydrided samples with nominal hydrogen concentrations of 0 (as-received), 150, 250, 500, 1200 and 2000 ppm were prepared. Hydrogen was precipitated as zirconium hydrides in the shape of platelets oriented along the hoop direction. Ring Compression Tests (RCTs) were conducted at three temperatures (20, 135 and 300 °C) and two displacement rates (0.5 and 100 mm/min). A new method has been proposed in this paper which allows the determination of fracture toughness from ring compression tests. The proposed method combines the experimental results, the cohesive crack model, finite elements simulations, numerical calculations and non-linear optimization techniques. The parameters of the cohesive crack model were calculated by minimizing the difference between the experimental data and the numerical results. An almost perfect fitting of the experimental results is achieved by this method. In addition, an estimation of the error in the calculated fracture toughness is also provided.
Bravin, E; Sosa, A
2014-01-01
This report summarizes the results of a series of tests performed on the prototype HIE-ISOLDE diagnostic box (HIE-DB) regarding the vibrations and drifts in the transverse position of the scanning blade while moving in and out of beam path in the HIE-ISOLDE short box prototype. To monitor the transverse position of the blade, a series of 0.1 mm diameter holes were drilled on it and their positions were tracked with an optical system. The linear motion actuator was acquired from UHV design (model LSM38-150-SS), and it was adapted to be driven by a brushless EC motor from MAXON. The speed of the scanning blade during the tests was 10 mm/s. The transverse movement of the slit in the direction perpendicular to the movement was lower than 40 m, and is dominated by the displacement of the contact point of the applied force on the lead-screw. An offset on the slit position was observed while changing the direction of movement of the blade, its amplitude being of the order of 30 m. The amplitudes of the displacements...
Bravin, E; Sosa, A
2014-01-01
This report summarizes the results of a series of tests performed on the prototype HIE-ISOLDE diagnostic box (HIE-DB) regarding the vibrations and drifts in the transverse position of the scanning blade while moving inside or outside the box. To monitor the transverse position of the blade, a series of 0.1 mm diameter holes were drilled on it and their positions were tracked with an optical system. The linear motion actuator was acquired from UHV design (model LSM38-150-SS), is driven by a stepper motor and has all the guiding mechanisms outside vacuum. The maximum speed of the scanning blade during the tests was 2.5 mm/s. The transverse movement of the slit in the direction perpendicular to the movement was lower than 50 m, and is dominated by the displacement of the contact point of the applied force on the lead-screw. An offset on the slit position was observed while changing the direction of movement of the blade, its amplitude being of the order of 30 m. The amplitudes of the displacements of the transve...
Suzuki, Taku; Iwamoto, Takuji; Shizu, Kanae; Suzuki, Katsuji; Yamada, Harumoto; Sato, Kazuki
2017-05-01
This retrospective study was designed to investigate prognostic factors for postoperative outcomes for cubital tunnel syndrome (CubTS) using multiple logistic regression analysis with a large number of patients. Eighty-three patients with CubTS who underwent surgeries were enrolled. The following potential prognostic factors for disease severity were selected according to previous reports: sex, age, type of surgery, disease duration, body mass index, cervical lesion, presence of diabetes mellitus, Workers' Compensation status, preoperative severity, and preoperative electrodiagnostic testing. Postoperative severity of disease was assessed 2 years after surgery by Messina's criteria which is an outcome measure specifically for CubTS. Bivariate analysis was performed to select candidate prognostic factors for multiple linear regression analyses. Multiple logistic regression analysis was conducted to identify the association between postoperative severity and selected prognostic factors. Both bivariate and multiple linear regression analysis revealed only preoperative severity as an independent risk factor for poor prognosis, while other factors did not show any significant association. Although conflicting results exist regarding prognosis of CubTS, this study supports evidence from previous studies and concludes early surgical intervention portends the most favorable prognosis. Copyright © 2017 The Japanese Orthopaedic Association. Published by Elsevier B.V. All rights reserved.
Integration process and logistics results
2004-01-01
The Procurement and Logistics functions have gone through a process of integration since the beginning of integrated management of Asco and Vandellos II up to the present. These are functions that are likely to be designed for delivering a single product to the rest of the organization, defined from a high level of expectations, and that admit simplifications and materialization of synergy's as they are approached from an integrated perspective. The analyzed functions are as follows: Service and Material Purchasing, Warehouse and Material Management, and Documentation and General Services Management. In all case, to accomplish the integration, objectives, procedures and information systems were unified. As for the organization, a decision was made in each case on whether or not to out source. The decisive corporate strategy to integrate, resulting in actions such as moving corporate headquarters to Vandellos II, corporate consolidation, regulation of employment and implementation of the ENDESA Group Economic Information System (SIE) , has shaped this process, which at present can be considered as practically complete. (Author)
[Logistics in the pharmaceutical service].
Stanko, P; Fulmeková, M
2005-11-01
The conception of the field of pharmaceutical service defines pharmaceutical service as the basic part of pharmacy, the principal task of which is to provide pharmaceutical care as an inseparable part of providing health care. It represents a set of professional activities of the pharmacist oriented to securing human and veterinary pharmaceutical products and health care products and to optimising effective, safe and quality pharmacotherapy. Technically, pharmaceutical service is an applied discipline, as it makes use of knowledge gained in other pharmaceutical, medical, psychological, social, and economic sciences. Because of its interdisciplinary character it is necessary to extend the theory of pharmaceutical service in such a way so that it may reflect all aspects of its sphere of activity. One of the possibilities is to define the pharmacy premises as an independent functional unit which operates on the basis of valid legal standards in such a way that on the one hand it secures the provision of health (pharmaceutical) care, and on the other hand it maintains its cost-effectiveness. To keep the quality of care of the patient and the economic aspect in balance, it is necessary to define the term pharmaceutical logistics also under the conditions of Slovak (Czech) pharmacy as early satisfaction of the requirements of the patient (client) in the pharmacy premises, which means that the appropriate pharmaceutical product or health care product and the appropriate information must be at the right time in the required amount and required quality in the right place.
Country logistics performance and disaster impact.
Vaillancourt, Alain; Haavisto, Ira
2016-04-01
The aim of this paper is to deepen the understanding of the relationship between country logistics performance and disaster impact. The relationship is analysed through correlation analysis and regression models for 117 countries for the years 2007 to 2012 with disaster impact variables from the International Disaster Database (EM-DAT) and logistics performance indicators from the World Bank. The results show a significant relationship between country logistics performance and disaster impact overall and for five out of six specific logistic performance indicators. These specific indicators were further used to explore the relationship between country logistic performance and disaster impact for three specific disaster types (epidemic, flood and storm). The findings enhance the understanding of the role of logistics in a humanitarian context with empirical evidence of the importance of country logistics performance in disaster response operations. © 2016 The Author(s). Disasters © Overseas Development Institute, 2016.
3PL Services in City Logistics
Aastrup, Jesper; Gammelgaard, Britta; Prockl, Günter
2012-01-01
The purpose of this paper is 1) to develop an overview of activities and services that can add value for users and consignees in city logistics schemes based on Urban Consolidation Centre, and 2) to understand and analyze the perceived value for users and consignees from using such services....... The paper will be based on studies of the city logistics literature and existing city logistics schemes, as well as survey and interview findings from studies of potential users (retailers) in Copenhagen inner city and interviews with existing users (retailers) of existing city logistics services...... in the cities of Maastricht, Netherlands, and Hasselt, Belgium. The paper provides an overview and classification of possible third party logistics services in city logistics schemes. Also, findings about value perceived by current users as well as potential users are presented. Literature on city logistics has...
Metaheuristic analysis in reverse logistics of waste
Serrano Elena, A.
2016-07-01
This paper focuses in the use of search metaheuristic techniques on a dynamic and deterministic model to analyze and solve cost optimization problems and location in reverse logistics, within the field of municipal waste management of Málaga (Spain). In this work we have selected two metaheuristic techniques having relevance in present research, to test the validity of the proposed approach: an important technique for its international presence as is the Genetic Algorithm (GA) and another interesting technique that works with swarm intelligence as is the Particles Swarm Optimization (PSO). These metaheuristic techniques will be used to solve cost optimization problems and location of MSW recovery facilities (transfer centers and treatment plants). (Author)
Feng Chung Wu
2004-12-01
Full Text Available Objetivo: Apresentação do teste biomecânico Energia Total de Ruptura para o estudo da resistência intrínseca de material biológico com propriedade viscoelástica não-linear representado neste trabalho por segmento íntegro de cólon descendente de rato. Métodos: Implementação do teste biomecânico Energia Total de Ruptura e do Sistema de Aquisição e Análise de dados Biomecânicos - SABI 2.0. Para esse fim, foram utilizados conceitos físico-mecânicos, computacionais e biomecânicos e como corpos de teste, 15 espécimes de cólon descendente de ratos. Resultados: O teste biomecânico Energia Total de Ruptura permitiu o cálculo da energia total acumulada necessária para promover a ruptura dos corpos de prova durante os ensaios mecânicos. Por meio da automatização e gerenciamento da aquisição e análise dos dados capturados foi possível a geração de gráficos e relatórios descritivos e estatísticos. Conclusão: Fundamentado em conceitos físico-mecânicos, computacionais e biomecânicos, o teste Energia Total de Ruptura pôde proporcionar análise matemática do comportamento dos segmentos de cólon descendente de ratos durante os ensaios, demonstrando ser um possível método de medição da resistência intrínseca desse material biológico com propriedade viscoelástica não-linear.Purpose: Presentation of the Total Energy of Rupture biomechanical test to evaluate the intrinsic resistance of the rat’s left colon which presents a non-linear viscoelastic property. Methods: Implementation of Total Energy of Rupture test (ETR and the Biomechanical Data Acquisition and Analysis System (SABI 2.0 based on physic-mechanical, computational and biomechanical concepts. Fifteen specimens of Wistar adults rat’s left colon where considered for experiments. Results: Using the TER biomechanical test it was possible calculate the accumulated total energy necessary to promote the specimens rupture during the mechanical trial. It was
Reduction of Linear Programming to Linear Approximation
Vaserstein, Leonid N.
2006-01-01
It is well known that every Chebyshev linear approximation problem can be reduced to a linear program. In this paper we show that conversely every linear program can be reduced to a Chebyshev linear approximation problem.
The system of account and control of logistics costs
Khayrullin Rustam Zinnatullovich
Full Text Available The process of organization of civil engineering provides the delivery of construction materials, equipment to the civil engineering objects in the required quantities at the specified time. Effective tool for solving this problem is logistics. The basic components of logistics costs, which occupy the largest share in the sum of all logistics costs, are transportation costs and storage costs. The civil engineering industry is very promising for the use of outsourcing. The main part of works on providing material and technical resources in most cases is transferred to the outsourcing of other companies, including the group of companies forming the holding. In large holding companies the chain of movement of materials, goods and productions: purchase of materials and goods, completion materials, production structures, storage, movement, transportation, etc. may include several companies belonging in holding. The goods can be moved from one warehouse to another, with or without change of the owner of goods. Each company is obliged to show each movement of goods in their financial accounting. During the goods’ movement within a group of companies from one storage to another, from one owner to another, the total costs of the goods rise. Sales within a group of companies lead, as a rule, to a gain by one of the companies and the logistic expenses of another company. Selling to a consumer provides a profit to the seller company. Therefore, the problem of adequate allocation of logistics expenses and profits between separate legal entity and the task of continuous accounting and control of logistics costs and earnings in large companies, is vital. The automated system for accounting and controlling of logistics costs is suggested. The developed system allows controlling logistics costs of refining, storage and transportation for each ton, pieces, linear or square meters of the shipped cargoes. The System is based on complex algorithms of distribution
The Logistics Performance Effect in International Trade
Azmat Gani
2017-12-01
Full Text Available The continuous growth in world trade depends on the efficiency of trade support structures such as the logistics services. Despite logistics integral role in supporting commercial activities, there has generally been a low level of analysis and trade policy research focus from trade practitioners. This paper explores the effect of logistics performance in international trade. The analysis draws on overall logistics performance as well as disaggregated measures of logistics specificities data for a large sample of countries. The empirical analysis involved the estimation of standard export and import equations incorporating measures of logistics performance. The findings show that the overall logistics performance is positively and statistically significantly correlated with exports and imports. The analysis is also extended by investigating if logistics specificities mattered for international trade. The findings reveal that several dimensions capturing logistics performance have statistically significant and positive effect, mostly on exports. The main policy implication is that continuous investment in logistics infrastructure and services can positively impact international trade.
LOGISTIC ACTIVITIES IN BELARUS: TRENDS AND CHALLENGES
P. V. Bozhanov
2017-01-01
Full Text Available Main results of investigations on logistics activities in the Republic of Belarus at year-end 2016 are presented in the paper. The paper identifies and analyzes basic components of this activity on the basis of economic evaluation of indices presented in annual State statistical reporting on logistics and transport and freight forwarding activities of the Republican organizations according to form 1-logistics (Mintrans – Ministry of Transport and Communications of the Republic of Belarus, a report of the Ministry of Transport and Communications of the Republic of Belarus on the results of the implementation of Republican Program for development of logistics systems and transit potential of the Republic of Belarus for the period of 2016–2020, World Bank reports on logistics performance index, some indices of logistics infrastructure position and also results of electronic questionnaire of the largest logistics centers of the Republic of Belarus. Methods of comparative analysis, generalization and economic analysis have been used in the process of research. The analysis has shown that a network of logistics centers with various specialization and forms of property are located and operating in all regions of the Republic of Belarus. Most of them are situated in the Minsk region near the II and IX trans-European transport corridors and in the Brest region near the border with Poland. Structure of the logistics centers includes temporary storage warehouses, customs warehouses, warehouses for general use, container terminals, car parking, customs clearance office, and automotive, railway and other cargo transport facilities. Indices of logistics activity in the Republic of Belarus demonstrate its development in 2016. Storage space of logistics centers and main financial and volumetric indices of logistics activity which are included in the State statistical reporting have been increased during in recent times. These facts testify to the demand for
Third-party Reverse logistics platform and method Based on Bilateral Resource Integration
Zheng Hong Zhen
2016-01-01
Full Text Available Dispersion of reverse logistics resources makes it difficult to create relationships between demanders and providers, thereby the personalized demand for the construction of enterprise reverse logistics cannot be satisfied and the service quality cannot be guaranteed. Aiming at these problems, this paper presents a platform and method of enterprise reverse logistics based on bilateral resource integration (RLBRI. The method creates a third-party reverse logistics platform to accumulate a mass of reverse logistics demanders and providers together. And the platform integrates bilateral resources and acts as an intermediary to establish relationships between two sides. Through the platform, a complete and high-quality business chain for enterprise reverse logistics will be built efficiently. Finally put forward an effective strategy of non-defective reverse logistics depends on the integrity checking service provided by third-party logistics. By using this strategy it can short the distance of non-defective reverse transportation. Computational tests validate the strategy.
Hastings, I.J.; Hunt, C.E.L.; Lipsett, J.J.; MacDonald, R.D.
1985-09-01
Experiments have been carried out using a 'sweep gas' technique to determine the behaviour of short-lived fission products within operating, intact UO 2 fuel elements. The Zircaloy-4-clad elements were 600 mm long and contained fuel of density 10.65 - 10.71 Mg/m 3 . A He-2% H 2 carrier gas swept gaseous or volatile fission products out of the operating fuel element past a gamma spectrometer for measurement. We outline our loop model and give full details of calculational procedures. In tests at linear powers of 45 (FIO-122) and 60 kW/m (FIO-124) to a maximum burnup of 80 MW.h/kg U, the species measured directly at the spectrometer during normal operation were generally the short-lived xenons and kryptons. Iodines were not observed during normal operation. The behaviour of I-133 and I-135 was deduced from the decay of Xe-133 and Xe-135 during reactor shutdowns. Plots of R/B (released/born) against λ (decay constant) or effective λ for all isotopes observed at 45 and 60 kW/m show that a line of slope -0.5, corresponding with diffusion kinetics, is a good fit to the measured xenon and krypton data. The inferred release of iodine fits the same line. From this we can extrapolate to an R/B for I-131 of about 5 x 10 -4 at 45 kW/m, and 3 x 10 -3 at 60 kW/m. Both tests were terminated by defects. Under defect conditions, R/B dependence on λ was about 0.6. I-131 release under defect conditions was 5 Ci and 60 mCi for FIO-122 and FI0-124, respectively. 22 refs
Sun, Qiang
2017-10-01
With the concerns of ecological and circular economy along with sustainable development, reverse logistics has attracted the attention of enterprise. How to achieve sustainable development of reverse logistics has important practical significance of enhancing low carbon competitiveness. In this paper, the system boundary of reverse logistics carbon footprint is presented. Following the measurement of reverse logistics carbon footprint and reverse logistics carbon capacity is provided. The influencing factors of reverse logistics carbon footprint are classified into five parts such as intensity of reverse logistics, energy structure, energy efficiency, reverse logistics output, and product remanufacturing rate. The quantitative research methodology using ADF test, Johansen co-integration test, and impulse response is utilized to interpret the relationship between reverse logistics carbon footprint and the influencing factors more accurately. This research finds that energy efficiency, energy structure, and product remanufacturing rate are more capable of inhibiting reverse logistics carbon footprint. The statistical approaches will help practitioners in this field to structure their reverse logistics activities and also help academics in developing better decision models to reduce reverse logistics carbon footprint.
Urban logistics profile – Yogyakarta city, Indonesia
Maria Sri Asih Anna
2018-01-01
Full Text Available In recent years, more rural areas are becoming urban areas accompanied by escalation of logistics activities. Unlike passenger transport, the planning, policy and control of freight transport in developing countries have not been integrated into a reliable and efficient logistics system. Therefore, generating city logistics profile is necessary in order to support the planning of urban logistics system. This study aims to establish a logistics profile of Yogyakarta city, Indonesia, by dividing urban zones into several homogeneous groups, judging from several aspects, including city area features, product characteristics and agents/delivery profile. Logistics profile variables were calculated based on administrative boundaries, resulting in 45 areas to be investigated. Profiles were matched in groups of homogeneous stores (A, large commercial stores (C and residential areas with local trade (D,with one overlapping profile, i.e. profile A and profile D, in some locations in the middle of the city.
E-LOGISTICS – MULTIMODAL TRANSPORT MANAGEMENT
Marcel LITRA
2013-05-01
Full Text Available The paper presents the role and the importance of logistics for products and services inorder to obtain the competitive advantage. After a short presentation of logistics evolution, we moveon to defining the logistics concept, respectively integrated logistics. The analysis of the logisticsactivities is based on the total cost concept and it has as a purpose the efficient and effectivemanagement of the physical flows of raw materials, materials and finite products, and of theinternational flows. The competitive advantage is ensured through the harmonization of the logisticsfunction with the other functions of the company and through the integration of the logistics chain ofall upstream and downstream organizations in order to ensure a high level of consumer service ateconomical costs under the farm of supply chain management. In the end we present the maintendencies in the evolution of logistics in the Romanian firms under the circumstances of the increaseof their international dimension.
Outsourcing Logistics Activities: Evidence from Slovenia
Klemen Kavčič
2016-12-01
Full Text Available The purpose of this research is to investigate how logistics outsourcing performs activities that have been traditionally carried out within the outsourcer’s company. The study examines the characteristics of logistics and transport services, which are important in cooperation with service providers. Two groups were formed according to the average values of the characteristics of logistics activities. ‘Cost, quality and response’ are important for the first group, while ‘logistics, environment and the ability to adapt to client processes’ are important for the second group. The results of the survey carried out in Slovenian enterprises show that both groups are primarily interested in express freight and shipment services, the difference lying in the understanding of logistics, mutual trust and brand recognition. The findings will be useful both in business practice and for managers, providing them with a better understanding of the performance of logistics outsourcing.
Anon.
1994-01-01
The aim of the TESLA (TeV Superconducting Linear Accelerator) collaboration (at present 19 institutions from seven countries) is to establish the technology for a high energy electron-positron linear collider using superconducting radiofrequency cavities to accelerate its beams. Another basic goal is to demonstrate that such a collider can meet its performance goals in a cost effective manner. For this the TESLA collaboration is preparing a 500 MeV superconducting linear test accelerator at the DESY Laboratory in Hamburg. This TTF (TESLA Test Facility) consists of four cryomodules, each approximately 12 m long and containing eight 9-cell solid niobium cavities operating at a frequency of 1.3 GHz
Integrated Computer System of Management in Logistics
Chwesiuk, Krzysztof
2011-06-01
This paper aims at presenting a concept of an integrated computer system of management in logistics, particularly in supply and distribution chains. Consequently, the paper includes the basic idea of the concept of computer-based management in logistics and components of the system, such as CAM and CIM systems in production processes, and management systems for storage, materials flow, and for managing transport, forwarding and logistics companies. The platform which integrates computer-aided management systems is that of electronic data interchange.
Facilitating Automation Development in Internal Logistics Systems
Granlund, Anna
2014-01-01
The internal logistics system includes all activities connected with managing the flow of materials within the physical limits of a facility. This system is an important part of operations in need of increased focus and continuous improvements. Automation is one possible tool with a previously confirmed great potential to improve internal logistics. Despite this great potential and a growing trend of using automation in the area, internal logistics activities are still not automated to the sa...
dLOGIS: Disaster Logistics Information System
Koesuma, Sorja; Riantana, Rio; Siswanto, Budi; Aji Purnomo, Fendi; Lelono, Sarjoko
2017-11-01
There are three timing of disaster mitigation which is pre-disaster, emergency response and post-disaster. All of those is important in disaster mitigation, but emergency response is important when we are talking about time. Emergency response has limited time when we should give help. Rapid assessment of kind of logistic, the number of survivors, number children and old people, their gender and also for difable person. It should be done in emergency response time. Therefore we make a mobile application for logistics management system. The name of application is dLOGIS, i.e. Disaster Logistics Information System. The application is based on Android system for mobile phone. Otherwise there is also website version. The website version is for maintenance, data input and registration. So the people or government can use it directly when there is a disaster. After login in dLOGIS, there is five main menus. The first main menu shows disaster information, refugees conditions, logistics needed, available logistics stock and already accepted logistics. In the second menu is used for entering survivors data. The field coordinator can enter survivors data based on the rapid assessment in disaster location. The third menu is used for entering kind of logistic. Number and kind of logistics are based on the BNPB needed standard for the survivor. The fourth menu displays the logistics stock available in field coordinator. And the last menu displays the logistics help that already accepted and sent by donation. By using this application when a disaster happened, field coordinator or local government can use maintenance distribution of logistics base on their needs. Also for donor people who will give help to survivor, they can give logistics with the corresponding of survivor needs.
Aerial Logistics Management for Carrier Onboard Delivery
2016-09-01
NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS AERIAL LOGISTICS MANAGEMENT FOR CARRIER ONBOARD DELIVERY by Samuel L. Chen September 2016...AND SUBTITLE AERIAL LOGISTICS MANAGEMENT FOR CARRIER ONBOARD DELIVERY 5. FUNDING NUMBERS 6. AUTHOR(S) Samuel L. Chen 7. PERFORMING ORGANIZATION NAME(S...delivery (COD) is the use of aircraft to transport people and cargo from a forward logistics site (FLS) to a carrier strike group (CSG). The goal of
Wine industry logistics in Republic of Macedonia
Ivanova, Violeta; Atanasoski, Drasko
2013-01-01
The theoretical characteristics of logistics and logistics systems are numerous, with specific characteristics, different implications and missions. Logistics activities in the wine industry are very important. Macedonia is a large exporter of wine. In terms of export value of agricultural products in Macedonia, wine is at the first place in terms of exports of alcoholic beverages, and at the second place immediately after the tobacco. The winemaking in Macedonia is continuously increasing, e...
IMPORTANCE OF LOGISTICS OPERATORS IN INTERNATIONAL MARKET
KATARZYNA GRONDYS; RUZENA LOVASOVA; ANNA STELMASZCZYK; WIKTOR JANIK
2014-01-01
The aim of the article is to present role and importance of logistics operations in international arena. The article focuses on forms of outsourcing in logistics and their evolution over the years. The article discusses in detail the scope of logistics operators' activities on global scale over several years. Article also presents results of research, their analysis according to the sector of activities, their percentage share and financial benefits of using 3PL service providers. The progres...
Accumulations and development in commercial logistics
Ion Schileru
2008-01-01
The work presents a connotative periplus and an evaluation of one of the most dynamic business fields- logistics. Although used for a long time in the military department, logistics has affirmed itself relatively recent in business field, where it brought revolutionary contributions and where it has a privileged statute. There are presented particular significations of logistics from some of the application fields: production, distribution, merchandise study. In addition, the whole vision of ...
Logistics Reduction Technologies for Exploration Missions
Broyan, James L., Jr.; Ewert, Michael K.; Fink, Patrick W.
2014-01-01
Human exploration missions under study are limited by the launch mass capacity of existing and planned launch vehicles. The logistical mass of crew items is typically considered separate from the vehicle structure, habitat outfitting, and life support systems. Although mass is typically the focus of exploration missions, due to its strong impact on launch vehicle and habitable volume for the crew, logistics volume also needs to be considered. NASA's Advanced Exploration Systems (AES) Logistics Reduction and Repurposing (LRR) Project is developing six logistics technologies guided by a systems engineering cradle-to-grave approach to enable after-use crew items to augment vehicle systems. Specifically, AES LRR is investigating the direct reduction of clothing mass, the repurposing of logistical packaging, the use of autonomous logistics management technologies, the processing of spent crew items to benefit radiation shielding and water recovery, and the conversion of trash to propulsion gases. Reduction of mass has a corresponding and significant impact to logistical volume. The reduction of logistical volume can reduce the overall pressurized vehicle mass directly, or indirectly benefit the mission by allowing for an increase in habitable volume during the mission. The systematic implementation of these types of technologies will increase launch mass efficiency by enabling items to be used for secondary purposes and improve the habitability of the vehicle as mission durations increase. Early studies have shown that the use of advanced logistics technologies can save approximately 20 m(sup 3) of volume during transit alone for a six-person Mars conjunction class mission.
Analysis of Jingdong Mall Logistics Distribution Model
Shao, Kang; Cheng, Feng
In recent years, the development of electronic commerce in our country to speed up the pace. The role of logistics has been highlighted, more and more electronic commerce enterprise are beginning to realize the importance of logistics in the success or failure of the enterprise. In this paper, the author take Jingdong Mall for example, performing a SWOT analysis of their current situation of self-built logistics system, find out the problems existing in the current Jingdong Mall logistics distribution and give appropriate recommendations.
Outsourcing of Transport and Logistics Services
Anton Ogorelc
2007-11-01
Full Text Available The author presents the results of the research in five parts,which are interconnected. After the introduction, in part two,entitled A Framework for Logistics Outsourcing Decisions,theoretical characteristics of outsourcing are presented. Partthree, Core Competences and Outsourcing, describes the logisticscompetences. Part 4, Transp011 and Logistics Outsourcingin Europe, discusses the trends in logistics development andoutsourcing. The paper will assist managers responsible for thedevelopment of logistics strategies. The paper offers a uniquebuyer-supplier pwtnership framework by proposing that the logisticsoutsourcing will increase the competitive advantage ofmanufacturing firms.