Design and radiation tests on a LED based emergency evacuation directional lighting

CERN Document Server

Trikoupis, Nikolaos

2017-01-01

A LED (Light Emitting Diode) based directional lighting system has been designed to indicate the best evacuation direction for applications like the Large Hadron Collider (LHC) tunnel. The design includes constraints for redundancy required by safety systems and for components selection by radiation effects. Most of the literature for radiation effects on LEDs concern digital communications systems, although some recent reports do exist for visible spectrum power LEDs and the reduction in light output versus dose is coherent with the results presented in this paper. Prototype lighting units were irradiated in CERN’s CHARM facility up to a Total Integrated Dose (TID) of 870 Gy and no failures were observed. This paper describes the basic design, presents field tests and the effects of radiation on the LEDs luminance.

Illumination sensing in LED lighting systems based on frequency-division multiplexing

NARCIS (Netherlands)

Yang, Hongming; Bergmans, J.W.M.; Schenk, T.C.W.

2009-01-01

Recently, light emitting diode (LED) based illumination systems have attracted considerable research interest. Such systems normally consist of a large number of LEDs. In order to facilitate the control of such high-complexity system, a novel signal processing application, namely illumination

Development of Key Technologies for White Lighting Based on Light-Emitting Diodes (LEDs)

Energy Technology Data Exchange (ETDEWEB)

Werner Goetz; Bill Imler; James Kim; Junko Kobayashi; Andrew Kim; Mike Krames; Rick Mann; Gerd Mueller-Mach; Anneli Munkholm; Jonathan Wierer

2004-03-31

This program was organized to focus on materials development issues critical to the acceleration of solid-state lighting, and was split into three major thrust areas: (1) study of dislocation density reduction for GaN grown on sapphire using 'cantilever epitaxy', and the impact of dislocation density on the performance of state-of-the-art high-power LEDs; (2) the evaluation of in situ techniques for monitoring gas phase chemistry and the properties of GaN-based layers during metal-organic vapor phase epitaxy (MOCVD), and (3) feasibility for using semiconductor nanoparticles ('quantum dots') for the down-conversion of blue or ultraviolet light to generate white light. The program included a partnership between Lumileds Lighting (epitaxy and device fabrication for high power LEDs) and Sandia National Laboratories (cantilever epitaxy, gas phase chemistry, and quantum dot synthesis). Key findings included: (1) cantilever epitaxy can provide dislocation density reduction comparable to that of more complicated approaches, but all in one epitaxial growth step; however, further improvements are required to realize significant gains in LED performance at high drive currents, (2) in situ tools can provide detailed knowledge about gas phase chemistry, and can be used to monitor and control epitaxial layer composition and temperature to provide improved yields (e.g., a fivefold increase in color targeting is demonstrated for 540nm LEDs), and (3) quantum efficiency for quantum dots is improved and maintained up to 70% in epoxy thin films, but further work is necessary to increase densification (absorption) and robustness before practical application to LEDs.

Sustainable LED Fluorescent Light Replacement Technology

Energy Technology Data Exchange (ETDEWEB)

None, None

2011-09-30

Ilumisys and the National Center for Manufacturing Sciences (NCMS) partnered on a three-year project awarded by the United States (U.S.) Department of Energy (DOE), to quantify the impacts of LED lamps, incandescent lamps and fluorescent benchmark lamps over a product lifecycle – i.e. to develop a sustainable design and manufacturing strategy that addresses product manufacturing, use, recycling and disposal scenarios for LED-based lighting. Based on the knowledge gained from extensive product tear-down studies of fluorescent and screw-in lighting products, lifecycle assessment tools, and accelerated lifecycle testing protocols, an interactive Sustainable LED Design Guide has been developed to aid architectural and lighting designers and engineers in making design decisions that consider three important environmental impacts (greenhouse gas emissions, energy use and mercury emission) across all phases of the life of an LED lighting product. Critical information developed for the lifecycle analysis and product feature comparisons is the useful life of the lighting product as well as its performance. The Design Guide is available at www.ncms.org, and was developed based on operational and durability testing of a variety of lighting products including power consumption, light output, and useful life of a lamp in order to allow a more realistic comparison of lamp designs. This report describes the main project tasks, results and innovative features of the lifecycle assessment (LCA)-based design tools, and the key considerations driving the sustainable design of LED lighting systems. The Design Guide incorporates the following three novel features for efficiently evaluating LED lighting features in value-chains: Bill-of-Materials (BOM) Builder – Designers may import process data for each component and supply functional data for the product, including power, consumption, lumen output and expected useful life: Environmental Impact Review – Designs are comparable

High efficiency GaN-based LEDs using plasma selective treatment of p-GaN surface

Energy Technology Data Exchange (ETDEWEB)

Lee, Young-Bae; Naoi, Yoshiki; Sakai, Shiro [Department of Electrical and Electronic Engineering, University of Tokushima, 2-1 Minami-josanjima, Tokushima 770-8506 (Japan); Takaki, Ryohei; Sato, Hisao [Nitride Semiconductor Co., Ltd., 115-7 Itayajima, Akinokami, Seto-cho, Naruto, Tokushima 771-0360 (Japan)

2003-11-01

We have studied a new method of increasing the extraction efficiency of a GaN-based light-emitting diode (LED) using a plasma surface treatment. In this method, prior to the evaporation of a semitransparent p-metal, the surface of a p-GaN located beneath a p-pad is selectively exposed to a nitrogen plasma in a reactive ion etching (RIE) chamber. The electrical characteristics of the plasma treated p-GaN remarkably changes its resistivity into semi-insulator without any parasitic damage. Since the LEDs with a new method have no light absorption in a p-pad region, a higher optical power can be extracted compared to a conventional LEDs without plasma selective treatment on the p-GaN surface. (copyright 2003 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

A controlled trial of the Litebook light-emitting diode (LED light therapy device for treatment of Seasonal Affective Disorder (SAD

Directory of Open Access Journals (Sweden)

Telner John

2007-08-01

Full Text Available Abstract Background Recent research has emphasized that the human circadian rhythm system is differentially sensitive to short wavelength light. Light treatment devices using efficient light-emitting diodes (LEDs whose output is relatively concentrated in short wavelengths may enable a more convenient effective therapy for Seasonal Affective Disorder (SAD. Methods The efficacy of a LED light therapy device in the treatment of SAD was tested in a randomized, double-blind, placebo-controlled, multi-center trial. Participants aged 18 to 65 with SAD (DSM-IV major depression with seasonal pattern were seen at Baseline and Randomization visits separated by 1 week, and after 1, 2, 3 and 4 weeks of treatment. Hamilton Depression Rating Scale scores (SIGH-SAD were obtained at each visit. Participants with SIGH-SAD of 20 or greater at Baseline and Randomization visits were randomized to active or control treatment: exposure to the Litebook LED treatment device (The Litebook Company Ltd., Alberta, Canada which delivers 1,350 lux white light (with spectral emission peaks at 464 nm and 564 nm at a distance of 20 inches or to an inactivated negative ion generator at a distance of 20 inches, for 30 minutes a day upon awakening and prior to 8 A.M. Results Of the 26 participants randomized, 23 completed the trial. Mean group SIGH-SAD scores did not differ significantly at randomization. At trial end, the proportions of participants in remission (SIGH-SAD less than 9 were significantly greater (Fisher's exact test, and SIGH-SAD scores, as percent individual score at randomization, were significantly lower (t-test, with active treatment than with control, both in an intent-to-treat analysis and an observed cases analysis. A longitudinal repeated measures ANOVA analysis of SIGH-SAD scores also indicated a significant interaction of time and treatment, showing superiority of the Litebook over the placebo condition. Conclusion The results of this pilot study support

Improving “color rendering” of LED lighting for the growth of lettuce

Science.gov (United States)

Han, Tao; Vaganov, Vitaliy; Cao, Shixiu; Li, Qiang; Ling, Lili; Cheng, Xiaoyao; Peng, Lingling; Zhang, Congzhi; Yakovlev, Alexey N.; Zhong, Yang; Tu, Mingjing

2017-04-01

Light plays a vital role on the growth and development of plant. On the base of white light with high color rendering to the benefit of human survival and life, we proposed to improve “color rendering” of LED lighting for accelerating the growth of lettuce. Seven spectral LED lights were adopted to irradiate the lettuces under 150 μmol·m-2·s-1 for a 16 hd-1 photoperiod. The leaf area and number profiles, plant biomass, and photosynthetic rate under the as-prepared LED light treatments were investigated. We let the absorption spectrum of fresh leaf be the emission spectrum of ideal light and then evaluate the “color rendering” of as-prepared LED lights by the Pearson product-moment correlation coefficient and CIE chromaticity coordinates. Under the irradiation of red-yellow-blue light with high correlation coefficient of 0.587, the dry weights and leaf growth rate are 2-3 times as high as the sharp red-blue light. The optimized LED light for lettuce growth can be presumed to be limited to the angle (about 75°) between the vectors passed through the ideal light in the CIE chromaticity coordinates. These findings open up a new idea to assess and find the optimized LED light for plant growth.

Light extraction from GaN-based LED structures on silicon-on-insulator substrates

Energy Technology Data Exchange (ETDEWEB)

Tripathy, S.; Teo, S.L.; Lin, V.K.X.; Chen, M.F. [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology, and Research), 117602 (Singapore); Dadgar, A.; Krost, A. [Institut fuer Exerimentelle Physik, Otto-von Guericke Universitaet Magdeburg, Universitaetsplatz 1, 39016 Magdeburg (Germany); AZZURRO Semiconductors AG, Universitaetsplatz 1, 39016 Magdeburg (Germany); Christen, J. [Institut fuer Exerimentelle Physik, Otto-von Guericke Universitaet Magdeburg, Universitaetsplatz 1, 39016 Magdeburg (Germany)

2010-01-15

Nano-patterning of GaN-based devices is a promising technology in the development of high output power devices. Recent researches have been focused on the realization of two-dimensional (2D) photonic crystal (PhC) structure to improve light extraction efficiency and to control the direction of emission. In this study, we have demonstrated improved light extraction from green light emitting diode (LED) structures on thin silicon-on-insulator (SOI) substrates using surface nanopatterning. Scanning electron microscopy (SEM) is used to probe the size, shape, and etch depth of nano-patterns on the LED surfaces. Different types of nanopatterns were created by e-beam lithography and inductively coupled plasma etching. The LED structures after post processing are studied by photoluminescence (PL) measurements. The GaN nanophotonic structures formed by ICP etching led to more than five-fold increase in the intensity of the green emission. The improved light extraction is due to the combination of SOI substrate reflectivity and photonic structures on top GaN LED surfaces. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Control and Driving Methods for LED Based Intelligent Light Sources

OpenAIRE

Beczkowski, Szymon

2012-01-01

High power light-emitting diodes allow the creation of luminaires capable of generating saturated colour light at very high efficacies. Contrary to traditional light sources like incandescent and high-intensity discharge lamps, where colour is generated using filters, LEDs use additive light mixing, where the intensity of each primary colour diode has to be adjusted to the needed intensity to generate specified colour. The function of LED driver is to supply the diode with power needed to ach...

Warm white LEDs lighting over Ra=95 and its applications

Science.gov (United States)

Kobashi, Katsuya; Taguchi, Tsunemasa

2007-02-01

We have for the first time developed warm white LEDs lighting using a combination of near ultraviolet LED and three-band (red, green and blue) white phosphors. This LED has the average color-rendering index Ra=96. Moreover, special color-rendering index R9 (red) and R15 (face color of Japanese) are estimated to be 95 and 97, respectively. We will describe the results of evaluation on the medical lighting applications such as operation, treatment and endoscope experiments, application to the LED fashions and application to the Japanese antique art (ink painting) lighting.

Effect of LED-LCU light irradiance distribution on mechanical properties of resin based materials

International Nuclear Information System (INIS)

Magalhães Filho, T.R.; Weig, K.M.; Costa, M.F.; Werneck, M.M.; Barthem, R.B.; Costa Neto, C.A.

2016-01-01

The objective of this study is to analyze the light power distribution along the tip end of the light guide of three LED-LCUs (Light Curing Units) and to evaluate its effect on the mechanical properties of a polymer based dental composite. Firstly, the light power distribution over the whole area of LED-LCU light guide surface was analyzed by three methods: visual projection observation, spectral measurement and optical spectral analysis (OSA). The light power distribution and the total irradiance were different for the three LEDs used, but the wavelength was within the camphorquinone absorption spectrum. The use of a blank sheet was quite on hand to make a qualitative analysis of a beam, and it is costless. Secondly, specimens of a hybrid composite with approximately 8 mm diameter and 2 mm thickness were produced and polymerized by 20 s exposition time to each LED-LCU. Thirdly, the elastic modulus (E) and hardness (HV) were measured throughout the irradiated area by instrumented micro-indentation test (IIT), allowing to correlate localized power and mechanical properties. Both E and HV showed to be very sensitive to local power and wavelength dependent, but they followed the beam power profile. It was also shown that the mechanical properties could be directly correlated to the curing process. Very steep differences in mechanical properties over very short distances may impair the material performance, since residual stresses can easily be built over it. - Highlights: • A resin based composite (RBC) was polymerized by three different Light Emitting Diodes. • Each LED had its beam profile visually, wavelength and power analyzed. • The effective polymerization power (EPP) varied from 28% to 52% of the total beam power. • Wavelength seems to be as relevant as power in the light curing process. • Mechanical properties depend on the simultaneous effect of wavelength and power.

Effect of LED-LCU light irradiance distribution on mechanical properties of resin based materials

Energy Technology Data Exchange (ETDEWEB)

Magalhães Filho, T.R.; Weig, K.M. [Faculdade de Odontologia, Universidade Federal Fluminense, Rua São Paulo 28, CEP 24020-150 Niterói (Brazil); Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil); Costa, M.F. [Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil); Werneck, M.M. [Engenharia Elétrica (COPPE), Universidade Federal do Rio de Janeiro, CP 68504, CEP: 21941-972 Rio de Janeiro (Brazil); Barthem, R.B. [Instituto de Física, Universidade Federal do Rio de Janeiro, CP 68528, CEP: 21941-972 Rio de Janeiro (Brazil); Costa Neto, C.A., E-mail: celio@metalmat.ufrj.br [Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil)

2016-06-01

The objective of this study is to analyze the light power distribution along the tip end of the light guide of three LED-LCUs (Light Curing Units) and to evaluate its effect on the mechanical properties of a polymer based dental composite. Firstly, the light power distribution over the whole area of LED-LCU light guide surface was analyzed by three methods: visual projection observation, spectral measurement and optical spectral analysis (OSA). The light power distribution and the total irradiance were different for the three LEDs used, but the wavelength was within the camphorquinone absorption spectrum. The use of a blank sheet was quite on hand to make a qualitative analysis of a beam, and it is costless. Secondly, specimens of a hybrid composite with approximately 8 mm diameter and 2 mm thickness were produced and polymerized by 20 s exposition time to each LED-LCU. Thirdly, the elastic modulus (E) and hardness (HV) were measured throughout the irradiated area by instrumented micro-indentation test (IIT), allowing to correlate localized power and mechanical properties. Both E and HV showed to be very sensitive to local power and wavelength dependent, but they followed the beam power profile. It was also shown that the mechanical properties could be directly correlated to the curing process. Very steep differences in mechanical properties over very short distances may impair the material performance, since residual stresses can easily be built over it. - Highlights: • A resin based composite (RBC) was polymerized by three different Light Emitting Diodes. • Each LED had its beam profile visually, wavelength and power analyzed. • The effective polymerization power (EPP) varied from 28% to 52% of the total beam power. • Wavelength seems to be as relevant as power in the light curing process. • Mechanical properties depend on the simultaneous effect of wavelength and power.

Enhanced light extraction from GaN-based LEDs with a bottom-up assembled photonic crystal

International Nuclear Information System (INIS)

Gong Haibo; Hao Xiaopeng; Wu Yongzhong; Cao Bingqiang; Xia Wei; Xu Xiangang

2011-01-01

Highlights: → Polystyrene (PS) microspheres were employed as a template. → A noninvasive photonic crystal was fabricated on the surface of GaN-based LED. → Periodic arrangement of bowl-like holes served as a photonic crystal with gradually changed fill factors. → The electroluminescence intensity of LED with a photonic crystal was significantly enhanced. - Abstract: Photonic crystal (PhC) structure is an efficient tool for light extraction from light-emitting diodes (LEDs). The fabrication of a large area PhC structure on the light output surface of LEDs often involves sophisticated equipments such as nanoimprint lithography machine. In this study a monolayer of polystyrene (PS) microspheres was employed as a template to fabricate a noninvasive photonic crystal of indium tin oxide (ITO) on the surface of GaN-based LED. PS spheres can help to form periodic arrangement of bowl-like holes, a photonic crystal with gradually changed fill factors. Importantly, the electroluminescence intensity of LED with a photonic crystal was significantly enhanced by 1.5 times compared to that of the conventional one under various forward injection currents.

Enhanced light extraction from GaN-based LEDs with a bottom-up assembled photonic crystal

Energy Technology Data Exchange (ETDEWEB)

Gong Haibo [State Key Lab of Crystal Materials, Shandong University, Jinan, 250100 (China); School of Materials Science and Engineering, University of Jinan, Jinan, 250022 (China); Hao Xiaopeng, E-mail: xphao@sdu.edu.cn [State Key Lab of Crystal Materials, Shandong University, Jinan, 250100 (China); Wu Yongzhong [State Key Lab of Crystal Materials, Shandong University, Jinan, 250100 (China); Cao Bingqiang [School of Materials Science and Engineering, University of Jinan, Jinan, 250022 (China); Xia Wei [Shandong Huaguang Optoelectronics Company, Ltd., Jinan, 250101 (China); Xu Xiangang [State Key Lab of Crystal Materials, Shandong University, Jinan, 250100 (China); Shandong Huaguang Optoelectronics Company, Ltd., Jinan, 250101 (China)

2011-08-15

Highlights: > Polystyrene (PS) microspheres were employed as a template. > A noninvasive photonic crystal was fabricated on the surface of GaN-based LED. > Periodic arrangement of bowl-like holes served as a photonic crystal with gradually changed fill factors. > The electroluminescence intensity of LED with a photonic crystal was significantly enhanced. - Abstract: Photonic crystal (PhC) structure is an efficient tool for light extraction from light-emitting diodes (LEDs). The fabrication of a large area PhC structure on the light output surface of LEDs often involves sophisticated equipments such as nanoimprint lithography machine. In this study a monolayer of polystyrene (PS) microspheres was employed as a template to fabricate a noninvasive photonic crystal of indium tin oxide (ITO) on the surface of GaN-based LED. PS spheres can help to form periodic arrangement of bowl-like holes, a photonic crystal with gradually changed fill factors. Importantly, the electroluminescence intensity of LED with a photonic crystal was significantly enhanced by 1.5 times compared to that of the conventional one under various forward injection currents.

Solid State pH Sensor Based on Light Emitting Diodes (LED) As Detector Platform

Science.gov (United States)

Lau, King Tong; Shepherd, R.; Diamond, Danny; Diamond, Dermot

2006-01-01

A low-power, high sensitivity, very low-cost light emitting diode (LED)-based device developed for low-cost sensor networks was modified with bromocresol green membrane to work as a solid-state pH sensor. In this approach, a reverse-biased LED functioning as a photodiode is coupled with a second LED configured in conventional emission mode. A simple timer circuit measures how long (in microsecond) it takes for the photocurrent generated on the detector LED to discharge its capacitance from logic 1 (+5 V) to logic 0 (+1.7 V). The entire instrument provides an inherently digital output of light intensity measurements for a few cents. A light dependent resistor (LDR) modified with similar sensor membrane was also used as a comparison method. Both the LED sensor and the LDR sensor responded to various pH buffer solutions in a similar way to obtain sigmoidal curves expected of the dye. The pKa value obtained for the sensors was found to agree with the literature value.

New Framework of Sustainable Indicators for Outdoor LED (Light Emitting Diodes Lighting and SSL (Solid State Lighting

Directory of Open Access Journals (Sweden)

Annika K. Jägerbrand

2015-01-01

Full Text Available Light emitting diodes (LEDs and SSL (solid state lighting are relatively new light sources, but are already widely applied for outdoor lighting. Despite this, there is little available information allowing planners and designers to evaluate and weigh different sustainability aspects of LED/SSL lighting when making decisions. Based on a literature review, this paper proposes a framework of sustainability indicators and/or measures that can be used for a general evaluation or to highlight certain objectives or aspects of special interest when choosing LED/SSL lighting. LED/SSL lighting is reviewed from a conventional sustainable development perspective, i.e., covering the three dimensions, including ecological, economic and social sustainability. The new framework of sustainable indicators allow prioritization when choosing LED/SSL products and can thereby help ensure that short-term decisions on LED/SSL lighting systems are in line with long-term sustainability goals established in society. The new framework can also be a beneficial tool for planners, decision-makers, developers and lighting designers, or for consumers wishing to use LED/SSL lighting in a sustainable manner. Moreover, since some aspects of LED/SSL lighting have not yet been thoroughly studied or developed, some possible future indicators are suggested.

Study and Implementation of White Power-LED Based Indoor Lighting Application for the Healthcare Sector

Science.gov (United States)

Chakraborty, A.; Ganguly, R.

With the current technological growth in the field of device fabrication, white power-LED's are available for solid state lighting applications. This is a paradigm shift from electrical lighting to electronic lighting. The implemented systems are showing some promise by saving a considerable amount of energy as well as providing a good and acceptable illumination level. However, the `useful life' of such devices is an important parameter. If the proper device is not chosen, the desired reliability and performance will not be obtained. In the present work, different parameters associated with reliability of such LED's are studied. Four different varieties of LED's are put to test the `useful life' as per IESNA LM 79 standard. From the results obtained, the proper LED is chosen for further application. Subsequently, lighting design is done for a hospital waiting room (indoor application) with 24 × 7 lighting requirements for replacement of existing CFLs there. The calculations show that although the initial cost is higher for LED based lighting, yet the savings on energy and replacement of the lamp results in a payback time of less than a year.

Compressive strength measurements of hybrid dental composites treated with dry heat and light emitting diodes (LED post cure treatment

Directory of Open Access Journals (Sweden)

Jenny Krisnawaty

2014-11-01

Full Text Available Hybrid composites are mostly used on large cavities as restorative dental materials, whether it is used directly or indirectly. The mechanical properties of composite resin shall increase if it is treated with post cure treatment. The aim of this study is to evaluate compressive strength differences between dry heat and Light Emitting Diodes (LED treatment on the hybrid dental composite. A quasi-experimental was applied on this research with a total of 30 samples that were divided into two groups. Each sample was tested using LLOYD Universal Testing Machine with 1 mm/min speed to evaluate the compressive strength. The compressive strength results were marked when the sample was broken. The results of two groups were then analyzed using t-test statistical calculation. The results of this study show that post cure treatment on hybrid composite using LED light box (194.138 MPa was lower than dry heat treatment (227.339 MPa, which was also significantly different from statistical analysis. It can be concluded that compressive strength of LED light box was lower than dry heat post-cure treatment on the hybrid composite resin.

Spatial layout optimization design of multi-type LEDs lighting source based on photoelectrothermal coupling theory

Science.gov (United States)

Xue, Lingyun; Li, Guang; Chen, Qingguang; Rao, Huanle; Xu, Ping

2018-03-01

Multiple LED-based spectral synthesis technology has been widely used in the fields of solar simulator, color mixing, and artificial lighting of plant factory and so on. Generally, amounts of LEDs are spatially arranged with compact layout to obtain the high power density output. Mutual thermal spreading among LEDs will produce the coupled thermal effect which will additionally increase the junction temperature of LED. Affected by the Photoelectric thermal coupling effect of LED, the spectrum of LED will shift and luminous efficiency will decrease. Correspondingly, the spectral synthesis result will mismatch. Therefore, thermal management of LED spatial layout plays an important role for multi-LEDs light source system. In the paper, the thermal dissipation network topology model considering the mutual thermal spreading effect among the LEDs is proposed for multi-LEDs system with various types of power. The junction temperature increment cased by the thermal coupling has the great relation with the spatial arrangement. To minimize the thermal coupling effect, an optimized method of LED spatial layout for the specific light source structure is presented and analyzed. The results showed that layout of LED with high-power are arranged in the corner and low-power in the center. Finally, according to this method, it is convenient to determine the spatial layout of LEDs in a system having any kind of light source structure, and has the advantages of being universally applicable to facilitate adjustment.

Solution of multi-element LED light sources development automation problem

Science.gov (United States)

Chertov, Aleksandr N.; Gorbunova, Elena V.; Korotaev, Valery V.; Peretyagin, Vladimir S.

2014-09-01

The intensive development of LED technologies resulted in the creation of multicomponent light sources in the form of controlled illumination devices based on usage of mentioned LED technologies. These light sources are used in different areas of production (for example, in the food industry for sorting products or in the textile industry for quality control, etc.). The use of LED lighting products in the devices used in specialized lighting, became possible due to wide range of colors of light, LED structures (which determines the direction of radiation, the spatial distribution and intensity of the radiation, electrical, heat, power and other characteristics), and of course, the possibility of obtaining any shade in a wide dynamic range of brightness values. LED-based lighting devices are notable for the diversity of parameters and characteristics, such as color radiation, location and number of emitters, etc. Although LED technologies have several advantages, however, they require more attention if you need to ensure a certain character of illumination distribution and/or distribution of the color picture at a predetermined distance (for example, at flat surface, work zone, area of analysis or observation). This paper presents software designed for the development of the multicomponent LED light sources. The possibility of obtaining the desired color and energy distribution at the zone of analysis by specifying the spatial parameters of the created multicomponent light source and using of real power, spectral and color parameters and characteristics of the LEDs is shown as well.

CMOS-compatible plenoptic detector for LED lighting applications.

Science.gov (United States)

Neumann, Alexander; Ghasemi, Javad; Nezhadbadeh, Shima; Nie, Xiangyu; Zarkesh-Ha, Payman; Brueck, S R J

2015-09-07

LED lighting systems with large color gamuts, with multiple LEDs spanning the visible spectrum, offer the potential of increased lighting efficiency, improved human health and productivity, and visible light communications addressing the explosive growth in wireless communications. The control of this "smart lighting system" requires a silicon-integrated-circuit-compatible, visible, plenoptic (angle and wavelength) detector. A detector element, based on an offset-grating-coupled dielectric waveguide structure and a silicon photodetector, is demonstrated with an angular resolution of less than 1° and a wavelength resolution of less than 5 nm.

Future Solid State Lighting using LEDs and Diode Lasers

DEFF Research Database (Denmark)

Petersen, Paul Michael

2014-01-01

applications. Within the coming years, it is expected that the efficiency of blue laser diodes will approach the efficiency of infrared diode lasers. This will enable high efficiency white light generation with very high lumen per watt values. SSL today is mainly based on phosphor converted blue light emitting......Lighting accounts for 20% of all electrical energy usage. Household lighting and commercial lighting such as public and street lighting are responsible for significant greenhouse gas emissions. Therefore, currently many research initiatives focus on the development of new light sources which shows...... significant savings. Solid state lighting (SSL) based on LEDs is today the most efficient light source for generation of high quality white light. Diode lasers, however, have the potential of being more efficient than LEDs for the generation of white light. A major advantage using diode lasers for solid state...

Solid State pH Sensor Based on Light Emitting Diodes (LED) As Detector Platform

OpenAIRE

Lau, King Tong; Shepherd, R.; Diamond, Danny; Diamond, Dermot

2006-01-01

A low-power, high sensitivity, very low-cost light emitting diode (LED)-based device developed for low-cost sensor networks was modified with bromocresol green membrane to work as a solid-state pH sensor. In this approach, a reverse-biased LED functioning as a photodiode is coupled with a second LED configured in conventional emission mode. A simple timer circuit measures how long (in microsecond) it takes for the photocurrent generated on the detector LED to discharge its capacitance from lo...

Ultrabroad linewidth orange-emitting nanowires LED for high CRI laser-based white lighting and gigahertz communications

KAUST Repository

Janjua, Bilal

2016-08-10

Group-III-nitride laser diode (LD)-based solid-state lighting device has been demonstrated to be droop-free compared to light-emitting diodes (LEDs), and highly energy-efficient compared to that of the traditional incandescent and fluorescent white light systems. The YAG:Ce3+ phosphor used in LD-based solid-state lighting, however, is associated with rapid degradation issue. An alternate phosphor/LD architecture, which is capable of sustaining high temperature, high power density, while still intensity- and bandwidth-tunable for high color-quality remained unexplored. In this paper, we present for the first time, the proof-of-concept of the generation of high-quality white light using an InGaN-based orange nanowires (NWs) LED grown on silicon, in conjunction with a blue LD, and in place of the compound-phosphor. By changing the relative intensities of the ultrabroad linewidth orange and narrow-linewidth blue components, our LED/LD device architecture achieved correlated color temperature (CCT) ranging from 3000 K to above 6000K with color rendering index (CRI) values reaching 83.1, a value unsurpassed by the YAG-phosphor/blue-LD counterpart. The white-light wireless communications was implemented using the blue LD through on-off keying (OOK) modulation to obtain a data rate of 1.06 Gbps. We therefore achieved the best of both worlds when orange-emitting NWs LED are utilized as “active-phosphor”, while blue LD is used for both color mixing and optical wireless communications.

Output blue light evaluation for phosphor based smart white LED wafer level packages.

Science.gov (United States)

Kolahdouz, Zahra; Rostamian, Ali; Kolahdouz, Mohammadreza; Ma, Teng; van Zeijl, Henk; Zhang, Kouchi

2016-02-22

This study presents a blue light detector for evaluating the output light of phosphor based white LED package. It is composed of a silicon stripe-shaped photodiode designed and implemented in a 2 μm BiCMOS process which can be used for wafer level integration of different passive and active devices all in just 5 lithography steps. The final device shows a high selectivity to blue light. The maximum responsivity at 480 nm is matched with the target blue LED illumination. The designed structure have better responsivity compared to simple photodiode structure due to reducing the effect of dead layer formation close to the surface because of implantation. It has also a two-fold increase in the responsivity and quantum efficiency compared to previously similar published sensors.

A design of LED adaptive dimming lighting system based on incremental PID controller

Science.gov (United States)

He, Xiangyan; Xiao, Zexin; He, Shaojia

2010-11-01

As a new generation energy-saving lighting source, LED is applied widely in various technology and industry fields. The requirement of its adaptive lighting technology is more and more rigorous, especially in the automatic on-line detecting system. In this paper, a closed loop feedback LED adaptive dimming lighting system based on incremental PID controller is designed, which consists of MEGA16 chip as a Micro-controller Unit (MCU), the ambient light sensor BH1750 chip with Inter-Integrated Circuit (I2C), and constant-current driving circuit. A given value of light intensity required for the on-line detecting environment need to be saved to the register of MCU. The optical intensity, detected by BH1750 chip in real time, is converted to digital signal by AD converter of the BH1750 chip, and then transmitted to MEGA16 chip through I2C serial bus. Since the variation law of light intensity in the on-line detecting environment is usually not easy to be established, incremental Proportional-Integral-Differential (PID) algorithm is applied in this system. Control variable obtained by the incremental PID determines duty cycle of Pulse-Width Modulation (PWM). Consequently, LED's forward current is adjusted by PWM, and the luminous intensity of the detection environment is stabilized by self-adaptation. The coefficients of incremental PID are obtained respectively after experiments. Compared with the traditional LED dimming system, it has advantages of anti-interference, simple construction, fast response, and high stability by the use of incremental PID algorithm and BH1750 chip with I2C serial bus. Therefore, it is suitable for the adaptive on-line detecting applications.

Materials and Designs for High-Efficacy LED Light Engines

Energy Technology Data Exchange (ETDEWEB)

Ibbetson, James [Cree, Inc., Durham, NC (United States); Gresback, Ryan [Cree, Inc., Durham, NC (United States)

2017-09-28

Cree, Inc. conducted a narrow-band downconverter (NBD) materials development and implementation program which will lead to warm-white LED light engines with enhanced efficacy via improved spectral efficiency with respect to the human eye response. New red (600-630nm) NBD materials could result in as much as a 20% improvement in warm-white efficacy at high color quality relative to conventional phosphor-based light sources. Key program innovations included: high quantum yield; narrow peak width; minimized component-level losses due to “cross-talk” and light scattering among red and yellow-green downconverters; and improved reliability to reach parity with conventional phosphors. NBD-enabled downconversion efficiency gains relative to conventional phosphors yielded an end-of-project LED light engine efficacy of >160 lm/W at room temperature and 35 A/cm2, with a correlated color temperature (CCT) of ~3500K and >90 CRI (Color Rending Index). NBD-LED light engines exhibited equivalent luminous flux and color point maintenance at >1,000 hrs. of highly accelerated reliability testing as conventional phosphor LEDs. A demonstration luminaire utilizing an NBD-based LED light engine had a steady-state system efficacy of >150 lm/W at ~3500K and >90 CRI, which exceeded the 2014 DOE R&D Plan luminaire milestone for FY17 of >150 lm/W at just 80 CRI.

LED Street Lighting Solutions: Flagstaff, Arizona as a Case Study

Science.gov (United States)

Hall, Jeffrey C.

2018-01-01

Dark-sky protection in Flagstaff, Arizona extends back to 1958, with the first ordinance in the City banning advertising floodlights. The current ordinance, adopted in 1989, is comprehensive and has played a critical role in maintaining the quality of the night sky for astronomy, tourism, public enjoyment, and other purposes. Flagstaff, like many communities around the world, is now working on a transition from legacy bulb-based technology to LED for its outdoor lighting. The City, Lowell Observatory, the U. S. Naval Observatory, and the Flagstaff Dark Skies Coalition have been working intensively for two years to identify an LED-based street lighting solution that will preserve the City's dark skies while meeting municipal needs. We will soon be installing test fixtures for an innovative solution incorporating narrow-band amber LED and modest amounts of low-CCT white LED. In this talk, I will review the types of LEDs available for outdoor lighting and discuss the plans for Flagstaff's street lighting in the LED era, which we hope will be a model for communities worldwide.

White LED visible light communication technology research

Science.gov (United States)

Yang, Chao

2017-03-01

Visible light communication is a new type of wireless optical communication technology. White LED to the success of development, the LED lighting technology is facing a new revolution. Because the LED has high sensitivity, modulation, the advantages of good performance, large transmission power, can make it in light transmission light signal at the same time. Use white LED light-emitting characteristics, on the modulation signals to the visible light transmission, can constitute a LED visible light communication system. We built a small visible optical communication system. The system composition and structure has certain value in the field of practical application, and we also research the key technology of transmitters and receivers, the key problem has been resolved. By studying on the optical and LED the characteristics of a high speed modulation driving circuit and a high sensitive receiving circuit was designed. And information transmission through the single chip microcomputer test, a preliminary verification has realized the data transmission function.

Effect of Led Lighting Colors for Laying Japanese Quails

Directory of Open Access Journals (Sweden)

KC Nunes

Full Text Available ABSTRACT Time of exposure and light intensity rearing house may affect the performance and egg quality of laying quails. This research aimed at evaluating the live performance, egg quality, biometry of the reproductive system, and the gastrointestinal tract of Japanese quails (Coturnix coturnix japonica exposed to artificial light-emitting diodes (LED of different colors in comparison with fluorescent lamps. A total of 240 Japanese quails were distributed in completely randomized experimental design with four treatments (fluorescent lamp, and green, red, or blue LED lamps with six replicates of 10 birds each. Average egg weight and eggshell thickness were different (p0.05. The oviduct of 64-d-old hens exposed to green LED lighting was shorter (p<0.05 than those exposed to the fluorescent lamp. Red LED can be used to replace the fluorescent lamps, as they promote the same live performance, egg quality, and morphological development of the reproductive tract of laying Japanese quails.

High-Voltage LED Light Engine with Integrated Driver

Energy Technology Data Exchange (ETDEWEB)

Soer, Wouter [Lumileds LLC, San Jose, CA (United States)

2016-02-29

LED luminaires have seen dramatic changes in cost breakdown over the past few years. The LED component cost, which until recently was the dominant portion of luminaire cost, has fallen to a level of the same order as the other luminaire components, such as the driver, housing, optics etc. With the current state of the technology, further luminaire performance improvement and cost reduction is realized most effectively by optimization of the whole system, rather than a single component. This project focuses on improving the integration between LEDs and drivers. Lumileds has developed a light engine platform based on low-cost high-power LEDs and driver topologies optimized for integration with these LEDs on a single substrate. The integration of driver and LEDs enables an estimated luminaire cost reduction of about 25% for targeted applications, mostly due to significant reductions in driver and housing cost. The high-power LEDs are based on Lumileds’ patterned sapphire substrate flip-chip (PSS-FC) technology, affording reduced die fabrication and packaging cost compared to existing technology. Two general versions of PSS-FC die were developed in order to create the desired voltage and flux increments for driver integration: (i) small single-junction die (0.5 mm²), optimal for distributed lighting applications, and (ii) larger multi-junction die (2 mm² and 4 mm²) for high-power directional applications. Two driver topologies were developed: a tapped linear driver topology and a single-stage switch-mode topology, taking advantage of the flexible voltage configurations of the new PSS-FC die and the simplification opportunities enabled by integration of LEDs and driver on the same board. A prototype light engine was developed for an outdoor “core module” application based on the multi-junction PSS-FC die and the single-stage switch-mode driver. The light engine meets the project efficacy target of 128 lm/W at a luminous flux

"Light-box" accelerated growth of poinsettias: LED-only illumination

Science.gov (United States)

Weerasuriya, Charitha; Detez, Stewart; Hock Ng, Soon; Hughes, Andrew; Callaway, Michael; Harrison, Iain; Katkus, Tomas; Juodkazis, Saulius

2018-01-01

For the current commercialized agricultural industry which requires a reduced product lead time to customer and supply all year round, an artificial light emitting diodes (LEDs)-based illumination has high potential due to high efficiency of electrical-to-light conversion. The main advantage of the deployed Red Green Blue Amber LED lighting system is colour mixing capability, which means ability to generate all the colours in the spectrum by using three or four primary colours LEDs. The accelerated plant growth was carried out in a "light-box" which was made to generate an artificial day/night cycle by moving the colour mixing ratio along the colour temperature curve of the chromaticity diagram. The control group of plants form the same initial batch was grown on the same shelf in a greenhouse at the same conditions with addition of artificial illumination by incandescent lamps for few hours. Costs and efficiency projections of LED lamps for horticultural applications is discussed together with required capital investment. The total cost of the "light-box" including LED lamps and electronics was 850 AUD.

The cinema LED lighting system design based on SCM

Science.gov (United States)

En, De; Wang, Xiaobin

2010-11-01

A LED lighting system in the modern theater and the corresponding control program is introduced. Studies show that moderate and mutative brightness in the space would attract audiences' attention on the screen easily. SCM controls LED dynamically by outputting PWM pulse in different duty cycle. That cinema dome lights' intensity can vary with the plot changed, make people get a better view of experience. This article expounds the architecture of hardware system in the schedule and the control flow of the host of the solution. Besides, it introduces the design of software as well. At last, the system which is proved energy-saving, reliable, good visual effect and having using value by means of producing a small-scale model, which reproduce the whole system and achieves the desired result.

Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

Energy Technology Data Exchange (ETDEWEB)

Johnstone, Peter; Jacobson, Arne; Mills, Evan; Mumbi, Maina

2009-02-11

The notion of"productive use" is often invoked in discussions about whether new technologies improve productivity or otherwise enhance commerce in developing-country contexts. It an elusive concept,especially when quantitative measures are sought. Improved and more energy efficient illumination systems for off-gridapplication--the focus of the Lumina Project--provide a case in which a significant productivity benefit can be imagined, given the importance of light to the successful performance of many tasks, and the very low quality of baseline illumination provided by flame-based source. This Research Note summarizes self-reported quantitative and qualitative impacts of switching to LED lighting technology on the prosperity of night-market business owners and operators. The information was gathered in the context of our 2008 market testing field work in Kenya?s Rift Valley Province, which was performed in the towns of Maai Mahiu and Karagita by Arne Jacobson, Kristen Radecsky, Peter Johnstone, Maina Mumbi, and others. Maai Mahiu is a crossroads town; provision of services to travelers and freight carriers is a primary income source for the residents. In contrast, the primary income for Karagita's residents is from work in the large, factory style flower farms on the eastern shores of Lake Naivasha that specialize in producing cut flowers for export to the European market. According to residents, both towns had populations of 6,000 to 8,000 people in June 2008. We focused on quantifying the economics of fuel-based and LED lighting technology in the context of business use by night market vendors and shop keepers. Our research activities with the business owners and operators included baseline measurement of their fuel-based lighting use, an initial survey, offering for sale data logger equipped rechargeable LED lamps, monitoring the adoption of the LED lamps, and a follow-up survey.

Studying Light Color using White LED Lighting

Science.gov (United States)

Yamagishi, Misako; Yamaba, Kazuo; Nagata, Manori; Kubo, Chiho; Nokura, Kunihiro

Recently, white Light Emitting Diodes (LEDs) are receiving attention worldwide as new lighting devices. This study examined effects of a lighting application on performance using white LEDs. The light color—the correlated color temperature (CCT) —was assessed. It affected to psychological states and physiological conditions. Three CCT conditions were respectively set for the experiment: 2500 K, 5000 K, and 8200 K. In all, 20 younger subjects (20-30 years old), 15 middle-aged to elderly subjects (45-60 years old) and 12 elderly subjects (over 65 years-old) participated. They were presented a Numerical Verification (NV) task for performance measurement. The psychological states on performance were evaluated using the lighting assessment questionnaire. The physiological conditions were recorded using an electrocardiograph. Results show that the effects of CCT differ among age groups. Especially, the performance of younger subjects might differ from CCT conditions; elderly subjects are affected by CCT condition because of their visual acuity or response to contrast of objects.

Practical lighting design with LEDs

CERN Document Server

Lenk, Ron

2016-01-01

The second edition of Practical Lighting Design with LEDs has been revised and updated to provide the most current information for developing light-emitting diodes products. The authors, noted authorities in the field, offer a review of the most relevant topics including optical performance, materials, thermal design, and modeling and measurement. Comprehensive in scope, the text covers all the information needed to design LEDs into end products.

Demonstration of 575-Mb/s downlink and 225-Mb/s uplink bi-directional SCM-WDM visible light communication using RGB LED and phosphor-based LED.

Science.gov (United States)

Wang, Yuanquan; Wang, Yiguang; Chi, Nan; Yu, Jianjun; Shang, Huiliang

2013-01-14

We propose and experimentally demonstrate a novel full-duplex bi-directional subcarrier multiplexing (SCM)-wavelength division multiplexing (WDM) visible light communication (VLC) system based on commercially available red-green-blue (RGB) light emitting diode (LED) and phosphor-based LED (P-LED) with 575-Mb/s downstream and 225-Mb/s upstream transmission, employing various modulation orders of quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM). For the downlink, red and green colors/wavelengths are assigned to carry useful information, while blue chip is just kept lighting to maintain the white color illumination, and for the uplink, the low-cost P-LED is implemented. In this demonstration, pre-equalization and post-equalization are also adopted to compensate the severe frequency response of LEDs. Using this scheme, 4-user downlink and 1-user uplink transmission can be achieved. Furthermore, it can support more users by adjusting the bandwidth of each sub-channel. Bit error rates (BERs) of all links are below pre-forward-error-correction (pre-FEC) threshold of 3.8x 10(-3) after 66-cm free-space delivery. The results show that this scheme has great potential in the practical VLC system.

Monochromic radiation through light-emitting diode (LED positively augments in vitro shoot regeneration in Orchid (Dendrobium sonia

Directory of Open Access Journals (Sweden)

Vandita Billore

2017-07-01

Full Text Available Monochromatic lights emitted by light-emitting diodes (LEDs have generated great interest for efficient and controlled growth in vitro, especially of plants which are endangered or require specific intensity and wavelength of light. In the present study, we have evaluated the effect of monochromatic LEDs on in vitro morphogenesis: growth, proliferation of shoot cultures, and rooting of Dendrobium sonia. Different light sources viz. white LEDs (W, blue LEDs (B, yellow LEDs (Y and red LEDs (R were tested under photoperiod of 16 h of exposure and 8 h of dark. The frequency of morphogenesis depended on the wavelength of the applied monochromatic light. Higher wavelength monochromatic light (yellow light was observed to induce higher shoot proliferation (98%, early PLB (protocorm-like bodies formation, differentiation into green buds and shoot initiation as compared to red, blue and white light treatments. Yellow light also yielded higher number of shoots per explants (29 shoots/explant than red, blue and white light treatments. The results suggest that the monochromatic light sources stimulate morphogenic effects on in vitro culture of Dendrobium sonia, and that yellow light treatment can be used to enhance the efficiency of micropropagation.

Energy savings by implementation of light quality LED lighting. Final report; Implementering af energibesparelser ved benyttelse af hoejkvalitets LED belysning. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

Dam-Hansen, C.; Thorseth, A.; Poulsen, Peter

2010-03-15

The project developed two new LED light sources and systems, emphasising the potential of LED technology for energy savings and lighting quality. A LED light source for display case lighting, replacing incandescent lamps, was successfully installed in the Treasury at Rosenborg Castle in Copenhagen, Denmark, and it was decided to extend the solution in 2010. Electricity savings of 74% were achieved. LED light sources replacing halogen bulbs in cooker hoods reduce electricity consumption by 69% and ensure even lighting of the entire working surface with about 500 lux at all cooking areas. Furthermore, a new LED optics system was patented. (ln)

LED Virtual Simulation based on Web3D

OpenAIRE

Lilan Liu; Liu Han; Zhiqi Lin; Manping Li; Tao Yu

2014-01-01

Regarding to the high price and low market popularity of current LED indoor lighting products, a LED indoor lighting platform is proposed based on Web3D technology. The internet virtual reality technology is integrated and applied into the LED collaborative e-commerce website with Virtools. According to the characteristics of the LED indoor lighting products, this paper introduced the method to build encapsulated model and three characteristics of LED lighting: geometrical, optical and behavi...

White light-emitting diodes (LEDs) using (oxy)nitride phosphors

International Nuclear Information System (INIS)

Xie, R-J; Hirosaki, N; Sakuma, K; Kimura, N

2008-01-01

(Oxy)nitride phosphors have attracted great attention recently because they are promising luminescent materials for phosphor-converted white light-emitting diodes (LEDs). This paper reports the luminescent properties of (oxy)nitride phosphors in the system of M-Si-Al-O-N (M = Li, Ca or Sr), and optical properties of white LEDs using a GaN-based blue LED and (oxy)nitride phosphors. The phosphors show high conversion efficiency of blue light, suitable emission colours and small thermal quenching. The bichromatic white LEDs exhibit high luminous efficacy (∼55 lm W -1 ) and the multi-phosphor converted white LEDs show high colour rendering index (Ra 82-95). The results indicate that (oxy)nitride phosphors demonstrate their superior suitability to use as down-conversion luminescent materials in white LEDs

Effect of LED light on seeds of Capsicum annuum L. var. serrano

Directory of Open Access Journals (Sweden)

Alejandra María Moreno-Jiménez

2017-11-01

Full Text Available Serrano pepper (Capsicum annuum L. is a crop of economic, nutritional and medicinal importance; so it is necessary to increase its production and improve its characteristics. The objective of this research was to evaluate the stimulatory effect of light emitting diodes (LEDs on serrano pepper seedlings. Germination percentage, stem length, leaf width, leaf length, number of leaves, total chlorophyll content and carotenoid content were analyzed. The seeds were exposed to white, blue and red LED light, using fluorescent light as a control and a photoperiod of 11/13 hours. Once germinated, the seedlings continued with exposure to light for 30 days. After the laboratory conditions, the seedlings were transferred to a greenhouse for 60 days. The results show that there were no significant differences between LED light treatments on seed germination. The variables stem length, leaf width and leaf length, were favored with red light. Blue and red LEDs highlighted by increasing the number of leaves. Seedlings treated with blue light showed the highest content of photosynthetic pigments (chlorophyll= 0.84 mg g-1, carotenoid= 0.12 mg g-1. In conclusion, the red LED light is effective for the growth of serrano pepper seedlings, while the production of photosynthetic pigments was favored by blue LED light.   Keywords: peppers, light-emitting diodes, germination, growth, photosynthetic pigments

EVALUATION OF ADOPTION OF LED LIGHTING TECHNOLOGY IN MALAYSIA

OpenAIRE

Khorasanizadeh, Hasti

2017-01-01

Electrical energy consumption in Malaysia is rapidly increasing with illumination being the second largest contributor to this increment. Light Emitting Diode (LED) could be a viable option to reduce the illumination based energy consumption. LEDs are energy efficient and easier to recycle compared to traditional lighting sources such as incandescent and fluorescent lamps. They also have longer life time and lower failure rate. In this thesis, the feasibility of replacing...

Continuous light-emitting Diode (LED) lighting for improving food quality

OpenAIRE

Lu, C; Bian, Z

2016-01-01

Lighting-emitting diodes (LEDs) have shown great potential for plant growth and development, with higher luminous efficiency and positive impact compared with other artificial lighting. The combined effects of red/blue or/and green, and white LED light on plant growth and physiology, including chlorophyll fluorescence, nitrate content and phytochemical concentration before harvest, were investigated. The results showed that continuous light (CL)\\ud exposure at pre-harvest can effectively redu...

Final report LED solutions for public lighting; Eindrapportage LED oplossingen voor openbare verlichting

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-04-15

This report examines if and how LED can be used for public lighting on a large scale. Pilot projects in 29 municipalities were assessed to test the usefulness of LED lighting. This final report provides answers to the questions that relate to the feasibility of the deployment of LED in public lighting and provides some practical pointers. [Dutch] Er is onderzocht of, en zo ja op welke wijze, LED grootschalig toegepast kan worden in de openbare verlichting (OVL). In 29 gemeenten in Nederland zijn proefprojecten geevalueerd om LED verlichting te toetsen op bruikbaarheid. Deze eindrapportage geeft antwoord op vragen die betrekking hebben op de haalbaarheid van de toepassing van LED binnen de OVL en geeft wat praktische aandachtspunten.

Anti-glare LED lamps with adjustable illumination light field.

Science.gov (United States)

Chen, Yung-Sheng; Lin, Chung-Yi; Yeh, Chun-Ming; Kuo, Chie-Tong; Hsu, Chih-Wei; Wang, Hsiang-Chen

2014-03-10

We introduce a type of LED light-gauge steel frame lamp with an adjustable illumination light field that does not require a diffusion plate. Base on the Monte Carlo ray tracing method, this lamp has a good glare rating (GR) of 17.5 at 3050 lm. Compared with the traditional LED light-gauge steel frame lamp (without diffusion plate), the new type has low GR. The adjustability of the illumination light field could improve the zebra effect caused by the inadequate illumination light field of the lamp. Meanwhile, we adopt the retinal image analysis to discuss the influence of GR on vision. High GR could reflect stray light on the retinal image, which will reduce vision clarity and hasten the feeling of eye fatigue.

MudGet: Reproduction of the desired lighting environment using a smart-LED

Directory of Open Access Journals (Sweden)

Yong Hwi Kim

2017-07-01

Full Text Available With the emergence of smart LEDs, lighting based interior design is becoming popular. However, most of the smart LED-based lighting systems rely on expert-human intervention to create a desired atmosphere. For convenience, commercial lighting systems offer a number of options but their usability is fairly restricted. Therefore, an intuitive interface is required for novice users to generate the desired lighting environment. In this paper, we have developed a software, named MudGet, which automatically extracts the light mood from a digital image and controls the LED lamps to reproduce a desired lighting effect according to the extracted light mood. In our method, the light mood is regarded as a set of the representative colors of the digital image. The representative colors are extracted by utilizing K-means clustering algorithm. The dimming parameters are set for which each of the LED lamps create the lighting environment with the mood extracted by the software. To evaluate the feasibility of mood reproduction qualitatively, the degree of similarity between the light mood in the digital image and the reproduced result using LEDs is evaluated by a user study under a miniaturized experimental set. We observe that users can easily produce a desired atmosphere through the proposed MudGet software.

[LED lights in dermatology].

Science.gov (United States)

Noé, C; Pelletier-Aouizerate, M; Cartier, H

2017-04-01

The use in dermatology of light-emitting diodes (LEDs) continues to be surrounded by controversy. This is due mainly to poor knowledge of the physicochemical phases of a wide range of devices that are difficult to compare to one another, and also to divergences between irrefutable published evidence either at the level of in vitro studies or at the cellular level, and discordant clinical results in a variety of different indications: rejuvenation, acne, wound healing, leg ulcers, and cutaneous inflammatory or autoimmune processes. Therapeutic LEDs can emit wavelengths ranging from the ultraviolet, through visible light, to the near infrared (247-1300 nm), but only certain bands have so far demonstrated any real value. We feel certain that if this article remains factual, then readers will have a different, or at least more nuanced, opinion concerning the use of such LED devices in dermatology. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Setup of a LED light-pulser system for the OLYMPUS experiment; Aufbau eines LED-Lichtpulsersystems fuer das OLYMPUS-Experiment

Energy Technology Data Exchange (ETDEWEB)

Rehman, Waqaas

2011-12-15

The aim of this thesis consists in the construction and test of an external light-calibration system based on light-emitting diodes (LED) for the application at the symmetric Moller/Bhabha (SYMB) luminosity monitor. In chapter 2 the theoretical foundations of the OLYMPUS experiment, especially of the SYMB luminosity monitor are explained. Thereafter in chapter 3 the details of the setup of the OLYMPUS experiment and the fundamental properties of the SYMB detectors are discussed. In chapter 4 the whole concept of the LED light-pulser system is treated. In chapter 5 then test measurements with the ready LED light-pulser system are described. Thereby the light source shall be optimized in the shape that thereafter light pulses with short signal width are producable. Also different measurements for the unique characterization of the systems are performed. In chapter 6 light-intensity measurements during the operation of the LED light-pulser system are described.

Performance optimization of AlGaN-based LEDs by use of ultraviolet-transparent indium tin oxide: Effect of in situ contact treatment

Science.gov (United States)

Tu, Wenbin; Chen, Zimin; Zhuo, Yi; Li, Zeqi; Ma, Xuejin; Wang, Gang

2018-05-01

Ultraviolet (UV)-transparent indium tin oxide (ITO) grown by metal–organic chemical vapor deposition (MOCVD) is used as the current-spreading layer for 368 nm AlGaN-based light-emitting diodes (LEDs). By performing in situ contact treatment on the LED/ITO interface, the morphology, resistivity, and contact resistance of electrodes become controllable. Resistivity of 2.64 × 10‑4 Ω cm and transmittance at 368 nm of 95.9% are realized for an ITO thin film grown with Sn-purge in situ treatment. Therefore, the high-power operating voltage decreases from 3.94 V (without treatment) to 3.83 V (with treatment). The improved performance is attributed to the lowering of the tunneling barrier at the LED/ITO interface.

Plant growth regulation by the light of LEDs; LED ko wo tsukatta shokubutsu saibai gijutsu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H. [Mitsubishi Chemical Co., Tokyo (Japan). Yokohama Research Center

1996-03-01

Light Emitting Diode (LED) has not only an excellent display function for the luminescent device but also a superior feature without other lamps as light source for plant growth. It was National Aeronautics and Space Administration (NASA) to find out such merit for this light source for plant growth and try at first to use for plant growth at the space. They began to examine the LED application to the light source for the plant growth at the space since a stage at high cost of the LED, to develop some researches centered at cultivation of lettuce, wheat, and others. Finding out future possibility of cost-down of the LEDs on the cost/performance and large merits of the LEDs for control of the plant growth and plant physiology, authors have conducted some cultivation experiments of the plants using the LEDs for light source some years ago. In this papers, characterizations, actual possibility, and future developments of the LEDs for the light sources of the plant growth, are introduced. 5 refs., 4 figs.

LED lighting increases the ecological impact of light pollution irrespective of color temperature.

Science.gov (United States)

Pawson, S M; Bader, M K-F

Recognition of the extent and magnitude of night-time light pollution impacts on natural ecosystems is increasing, with pervasive effects observed in both nocturnal and diurnal species. Municipal and industrial lighting is on the cusp of a step change where energy-efficient lighting technology is driving a shift from “yellow” high-pressure sodium vapor lamps (HPS) to new “white” light-emitting diodes (LEDs). We hypothesized that white LEDs would be more attractive and thus have greater ecological impacts than HPS due to the peak UV-green-blue visual sensitivity of nocturnal invertebrates. Our results support this hypothesis; on average LED light traps captured 48% more insects than were captured with light traps fitted with HPS lamps, and this effect was dependent on air temperature (significant light × air temperature interaction). We found no evidence that manipulating the color temperature of white LEDs would minimize the ecological impacts of the adoption of white LED lights. As such, large-scale adoption of energy-efficient white LED lighting for municipal and industrial use may exacerbate ecological impacts and potentially amplify phytosanitary pest infestations. Our findings highlight the urgent need for collaborative research between ecologists and electrical engineers to ensure that future developments in LED technology minimize their potential ecological effects.

Active tracking system for visible light communication using a GaN-based micro-LED and NRZ-OOK.

Science.gov (United States)

Lu, Zhijian; Tian, Pengfei; Chen, Hong; Baranowski, Izak; Fu, Houqiang; Huang, Xuanqi; Montes, Jossue; Fan, Youyou; Wang, Hongyi; Liu, Xiaoyan; Liu, Ran; Zhao, Yuji

2017-07-24

Visible light communication (VLC) holds the promise of a high-speed wireless network for indoor applications and competes with 5G radio frequency (RF) system. Although the breakthrough of gallium nitride (GaN) based micro-light-emitting-diodes (micro-LEDs) increases the -3dB modulation bandwidth exceptionally from tens of MHz to hundreds of MHz, the light collected onto a fast photo receiver drops dramatically, which determines the signal to noise ratio (SNR) of VLC. To fully implement the practical high data-rate VLC link enabled by a GaN-based micro-LED, it requires focusing optics and a tracking system. In this paper, we demonstrate an active on-chip tracking system for VLC using a GaN-based micro-LED and none-return-to-zero on-off keying (NRZ-OOK). Using this novel technique, the field of view (FOV) was enlarged to 120° and data rates up to 600 Mbps at a bit error rate (BER) of 2.1×10 -4 were achieved without manual focusing. This paper demonstrates the establishment of a VLC physical link that shows enhanced communication quality by orders of magnitude, making it optimized for practical communication applications.

Unidirectional visible light communication and illumination with LEDs

NARCIS (Netherlands)

Li, S.; Pandharipande, A.; Willems, F.M.J.

2016-01-01

Visible light communication (VLC) with light emitting diodes (LEDs) has attracted interest for interactive and networked lighting control, and consumer infotainment applications. In this paper, we propose an LED system for jointly achieving unidirectional VLC while providing flicker-free

Green LED as an Effective Light Source for Curing Acrylate-Based Dental Resins in Combination with Irgacure 784

Directory of Open Access Journals (Sweden)

Katalin Bukovinszky

2018-01-01

Full Text Available Low intensity green light emitting diodes (LED were shown to be an effective light source to induce the photopolymerization of an acrylate-based photocurable dental restorative resin mixture of bisphenol A glycerolate dimethacrylate (BisGMA, triethylene glycol dimethacrylate (TEGDMA, and diurethane dimethacrylate (UDMA, in combination with fluorinated diaryl titanocene (Irgacure 784. Dental matrices were prepared by the LED light source at different intensities. The mechanical properties, such as Vickers microhardness, compressive strength, diametric tensile strength, flexural strength, and E-modulus of the created samples, were investigated. The kinetics of the photopolymerization was followed by Raman spectroscopy and conversion values were determined. It was found that, despite its narrow-emission range centered at a wavelength of 531 nm, the green LED light source is suitable for the preparation of dental matrices with good mechanical properties and high conversion values.

A comparative study of fluorescent and LED lighting in industrial facilities

Science.gov (United States)

Perdahci PhD, C.; Akin BSc, H. C.; Cekic Msc, O.

2018-05-01

Industrial facilities have always been in search for reducing outgoings and minimizing energy consumption. Rapid developments in lighting technology require more energy efficient solutions not only for industries but also for many sectors and for households. Addition of solid-state technology has brought LED lamps into play and with LED lamp usage, efficacy level has reached its current values. Lighting systems which uses fluorescent and LED lamps have become the prior choice for many industrial facilities. This paper presents a comparative study about fluorescent and LED based indoor lighting systems for a warehouse building in an industrial facility in terms of lighting distribution values, colour rendering, power consumption, energy efficiency and visual comfort. Both scenarios have been modelled and simulated by using Relux and photometric data for the luminaires have been gathered by conducting tests and measurements in an accredited laboratory.

White LEDs and modules in chip-on-board technology for general lighting

Science.gov (United States)

Hartmann, Paul; Wenzl, Franz P.; Sommer, Christian; Pachler, Peter; Hoschopf, Hans; Schweighart, Marko; Hartmann, Martin; Kuna, Ladislav; Jakopic, Georg; Leising, Guenther; Tasch, Stefan

2006-08-01

At present, light-emitting diode (LED) modules in various shapes are developed and designed for the general lighting, advertisement, emergency lighting, design and architectural markets. To compete with and to surpass the performance of traditional lighting systems, enhancement of Lumen output and the white light quality as well as the thermal management and the luminary integration are key factors for success. Regarding these issues, white LEDs based on the chip-on-board (COB) technology show pronounced advantages. State-of-the-art LEDs exploiting this technology are now ready to enter the general lighting segments. We introduce and discuss the specific properties of the Tridonic COB technology dedicated for general lighting. This technology, in combination with a comprehensive set of tools to improve and to enhance the Lumen output and the white light quality, including optical simulation, is the scaffolding for the application of white LEDs in emerging areas, for which an outlook will be given.

Development of high-performance solar LED lighting system

KAUST Repository

Huang, B.J.; Wu, M.S.; Hsu, P.C.; Chen, J.W.; Chen, K.Y.

2010-01-01

The present study developed a high-performance charge/discharge controller for stand-alone solar LED lighting system by incorporating an nMPPO system design, a PWM battery charge control, and a PWM battery discharge control to directly drive the LED. The MPPT controller can then be removed from the stand-alone solar system and the charged capacity of the battery increases 9.7%. For LED driven by PWM current directly from battery, a reliability test for the light decay of LED lamps was performed continuously for 13,200 h. It has shown that the light decay of PWM-driven LED is the same as that of constant-current driven LED. The switching energy loss of the MOSFET in the PWM battery discharge control is less than 1%. Three solar-powered LED lighting systems (18 W, 100 W and 150 W LED) were designed and built. The long-term outdoor field test results have shown that the system performance is satisfactory with the control system developed in the present study. The loss of load probability for the 18 W solar LED system is 14.1% in winter and zero in summer. For the 100 W solar LED system, the loss of load probability is 3.6% in spring. © 2009 Elsevier Ltd. All rights reserved.

Development of high-performance solar LED lighting system

International Nuclear Information System (INIS)

Huang, B.J.; Wu, M.S.; Hsu, P.C.; Chen, J.W.; Chen, K.Y.

2010-01-01

The present study developed a high-performance charge/discharge controller for stand-alone solar LED lighting system by incorporating an nMPPO system design, a PWM battery charge control, and a PWM battery discharge control to directly drive the LED. The MPPT controller can then be removed from the stand-alone solar system and the charged capacity of the battery increases 9.7%. For LED driven by PWM current directly from battery, a reliability test for the light decay of LED lamps was performed continuously for 13,200 h. It has shown that the light decay of PWM-driven LED is the same as that of constant-current driven LED. The switching energy loss of the MOSFET in the PWM battery discharge control is less than 1%. Three solar-powered LED lighting systems (18 W, 100 W and 150 W LED) were designed and built. The long-term outdoor field test results have shown that the system performance is satisfactory with the control system developed in the present study. The loss of load probability for the 18 W solar LED system is 14.1% in winter and zero in summer. For the 100 W solar LED system, the loss of load probability is 3.6% in spring.

Development of high-performance solar LED lighting system

KAUST Repository

Huang, B.J.

2010-08-01

The present study developed a high-performance charge/discharge controller for stand-alone solar LED lighting system by incorporating an nMPPO system design, a PWM battery charge control, and a PWM battery discharge control to directly drive the LED. The MPPT controller can then be removed from the stand-alone solar system and the charged capacity of the battery increases 9.7%. For LED driven by PWM current directly from battery, a reliability test for the light decay of LED lamps was performed continuously for 13,200 h. It has shown that the light decay of PWM-driven LED is the same as that of constant-current driven LED. The switching energy loss of the MOSFET in the PWM battery discharge control is less than 1%. Three solar-powered LED lighting systems (18 W, 100 W and 150 W LED) were designed and built. The long-term outdoor field test results have shown that the system performance is satisfactory with the control system developed in the present study. The loss of load probability for the 18 W solar LED system is 14.1% in winter and zero in summer. For the 100 W solar LED system, the loss of load probability is 3.6% in spring. © 2009 Elsevier Ltd. All rights reserved.

Reliable LED Lighting Technologies: Key Factors and Procurement Guidance

Energy Technology Data Exchange (ETDEWEB)

Davis, Lynn; Arquit Niederberger, Anne

2015-10-08

Abstract— Lighting systems have the ability to transform the economic and educational infrastructure of disadvantaged communities, and eradicating “light poverty” has become one of the primary goals of the International Year of Light 2015. Solid-state lighting (SSL) technology, based on light-emitting diode (LED) light sources, has emerged as the next generation of lighting technology, with a current global market penetration of roughly 5%. This paper will report on recent research on understanding SSL lighting system reliability (failure modes, environmental stressors, electrical power quality); discuss the implications of SSL technology reliability for providing lighting services; and suggest practical approaches to ensure SSL reliability to benefit humanity. Among the key findings from this work is that LED sources can be extremely reliable, withstanding a broad range of environmental stresses without failure. Nonetheless, SSL lighting systems can have a negative impact on electrical power reliability, as well as on the affordability of lighting services, without attention to the quality of the accompanying power infrastructure. It is therefore critical to ensure that the performance of the power supply electronics used in lighting systems is matched to the quality of the power source, when evaluating energy efficient lighting choices.

Effect of light dispersion of LED curing lights on resin composite polymerization.

Science.gov (United States)

Vandewalle, Kraig S; Roberts, Howard W; Andrus, Jeffrey L; Dunn, William J

2005-01-01

This study evaluated the effect of light dispersion of halogen and LED curing lights on resin composite polymerization. One halogen (Optilux 501, SDS/Kerr, Orange, CA, USA) and five light-emitting diode (LED) curing lights (SmartLite iQ, Dentsply Caulk, Milford, DE, USA; LEDemetron 1, SDS/Kerr; FLASHlite 1001, Discus Dental, Culver City, CA, USA; UltraLume LED 5, Ultradent Products, South Jordan, UT, USA; Allegro, Den-Mat, Santa Maria, CA, USA) were used in this study. Specimens (8 mm diameter by 2 mm thick) were made in polytetrafluoroethylene molds using hybrid (Z100, 3M ESPE, St. Paul, MN, USA) and microfill (A110, 3M ESPE) composite resins. The top surface was polymerized for 5 seconds with the curing light guide tip positioned at a distance of 1 and 5 mm. Degree of conversion (DC) of the composite specimens was analyzed on the bottom surface using micro-Fourier Transform Infrared (FTIR) spectroscopy (Perkin-Elmer FTIR Spectrometer, Wellesley, PA, USA) 10 minutes after light activation. DC at the bottom of the 2 mm specimen was expressed as a percentage of the mean maximum DC. Five specimens were created per curing light and composite type (n=5). Percent mean DC ratios and SDs were calculated for each light under each testing condition. Data were analyzed by analysis of variance (ANOVA)/Tukey's test (alpha = .05). A beam analyzer (LBA-700, Spiricon, Logan, UT, USA) was used to record the emitted light from the curing lights at 0 and 5 mm distances (n=5). A Top Hat factor was used to compare the quality of the emitted beam profile (LBA/PC, Spiricon). The divergence angle from vertical was also determined in the x- and y-axes (LBA/PC). Mean values and SDs were calculated for each light under each testing condition (0 and 5 mm, x- and y-axes) and analyzed by a two-way ANOVA/Tukey's test (alpha = .05). For DC ratios, significant differences were found based on curing light and curing distance (p < .05). At 1 mm, Optilux 501 and FLASHlite 1001 produced significantly

Intelligent control of dynamic LED lighting; Intelligent styring af dynamisk LED belysning. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

Thorseth, A.; Corell, D.; Hansen, Soeren S.; Dam-Hansen, C.; Petersen, Paul Michael

2013-01-15

The project has resulted in a prototype of a new intelligent lighting control system. The control system enables the end user to control his or her own local lighting environment (lighting zone) according to individual preferences and needs. The report provides a description of how the developed intelligent lighting system is composed and functions. The system is designed as a work lamp that enables dynamic change of the light color scheme according to a number of light control algorithms. It is specifically designed in relation to user tests of the intelligent lighting system, which is carried out in the final part of the project. An intelligent and advanced control of LED lighting was developed, which enables optimization of the user's light conditions in a given situation. Based on a number of known parameters, the system can control lighting so that at any time optimal light conditions are created, using a minimum of electric power. (LN)

Large-signal modulation characteristics of a GaN-based micro-LED for Gbps visible-light communication

Science.gov (United States)

Tian, Pengfei; Wu, Zhengyuan; Liu, Xiaoyan; Fang, Zhilai; Zhang, Shuailong; Zhou, Xiaolin; Liu, Kefu; Liu, Ming-Gang; Chen, Shu-Jhih; Lee, Chia-Yu; Cong, Chunxiao; Hu, Laigui; Qiu, Zhi-Jun; Zheng, Lirong; Liu, Ran

2018-04-01

The large-signal modulation characteristics of a GaN-based micro-LED have been studied for Gbps visible-light communication. With an increasing signal modulation depth the modulation bandwidth decreases, which matches up with the increase in the sum of the signal rise time and fall time. By simulating the band diagram and the carrier recombination rate of the micro-LED under large-signal modulation, carrier recombination and the carrier sweep-out effect are analyzed and found to be the dominant mechanisms behind the variation of modulation bandwidth. These results give further insight into improving the modulation bandwidth for high-speed visible-light communication.

Testing a high-power LED based light source for hyperspectral imaging microscopy

Science.gov (United States)

Klomkaew, Phiwat; Mayes, Sam A.; Rich, Thomas C.; Leavesley, Silas J.

2017-02-01

Our lab has worked to develop high-speed hyperspectral imaging systems that scan the fluorescence excitation spectrum for biomedical imaging applications. Hyperspectral imaging can be used in remote sensing, medical imaging, reaction analysis, and other applications. Here, we describe the development of a hyperspectral imaging system that comprised an inverted Nikon Eclipse microscope, sCMOS camera, and a custom light source that utilized a series of high-power LEDs. LED selection was performed to achieve wavelengths of 350-590 nm. To reduce scattering, LEDs with low viewing angles were selected. LEDs were surface-mount soldered and powered by an RCD. We utilized 3D printed mounting brackets to assemble all circuit components. Spectraradiometric calibration was performed using a spectrometer (QE65000, Ocean Optics) and integrating sphere (FOIS-1, Ocean Optics). Optical output and LED driving current were measured over a range of illumination intensities. A normalization algorithm was used to calibrate and optimize the intensity of the light source. The highest illumination power was at 375 nm (3300 mW/cm2), while the lowest illumination power was at 515, 525, and 590 nm (5200 mW/cm2). Comparing the intensities supplied by each LED to the intensities measured at the microscope stage, we found there was a great loss in power output. Future work will focus on using two of the same LEDs to double the power and finding more LED and/or laser diodes and chips around the range. This custom hyperspectral imaging system could be used for the detection of cancer and the identification of biomolecules.

Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products Part 2: LED Manufacturing and Performance

Energy Technology Data Exchange (ETDEWEB)

Scholand, Michael; Dillon, Heather E.

2012-05-01

Part 2 of the project (this report) uses the conclusions from Part 1 as a point of departure to focus on two objectives: producing a more detailed and conservative assessment of the manufacturing process and providing a comparative LCA with other lighting products based on the improved manufacturing analysis and taking into consideration a wider range of environmental impacts. In this study, we first analyzed the manufacturing process for a white-light LED (based on a sapphire-substrate, blue-light, gallium-nitride LED pumping a yellow phosphor), to understand the impacts of the manufacturing process. We then conducted a comparative LCA, looking at the impacts associated with the Philips Master LEDbulb and comparing those to a CFL and an incandescent lamp. The comparison took into account the Philips Master LEDbulb as it is now in 2012 and then projected forward what it might be in 2017, accounting for some of the anticipated improvements in LED manufacturing, performance and driver electronics.

Integration of organic LEDs with inorganic LEDs for a hybrid lighting system

Science.gov (United States)

Kong, H. J.; Park, J. W.; Kim, Y. M.

2013-01-01

We demonstrate that a surface-emitting hybrid light source can be realized by a combination of organic and inorganic light-emitting devices (LEDs). To this end, a blue inorganic LED bar is deployed at one side of a transparent light guide plate (LGP), and a yellow organic LED (OLED) is in contact with the rear surface of the LGP. In such a configuration, it is found that the overall luminance is almost equivalent to the sum of the luminances measured from each light source, and the overall luminance uniformity is determined mainly by the luminance uniformity of the OLED panel at high luminances. We have achieved a white color showing the Commission Internationale d'Eclairage (CIE) chromaticity coordinates of (x = 0.34, y = 0.33), the power efficiency of 9.3 lm/W, the luminance uniformity of 63% at the luminance of 3100 cd m-2, the color rendering index as high as 89.3, and the correlated color temperature finely tunable within the range between 3000 and 8000 K. Such a system facilitates color tuning by adjusting their luminous intensities and hence the implementation of the emotional lighting system.

Integration of organic LEDs with inorganic LEDs for a hybrid lighting system

International Nuclear Information System (INIS)

Kong, H J; Kim, Y M; Park, J W

2013-01-01

We demonstrate that a surface-emitting hybrid light source can be realized by a combination of organic and inorganic light-emitting devices (LEDs). To this end, a blue inorganic LED bar is deployed at one side of a transparent light guide plate (LGP), and a yellow organic LED (OLED) is in contact with the rear surface of the LGP. In such a configuration, it is found that the overall luminance is almost equivalent to the sum of the luminances measured from each light source, and the overall luminance uniformity is determined mainly by the luminance uniformity of the OLED panel at high luminances. We have achieved a white color showing the Commission Internationale d'Eclairage (CIE) chromaticity coordinates of (x = 0.34, y = 0.33), the power efficiency of 9.3 lm/W, the luminance uniformity of 63% at the luminance of 3100 cd m –2 , the color rendering index as high as 89.3, and the correlated color temperature finely tunable within the range between 3000 and 8000 K. Such a system facilitates color tuning by adjusting their luminous intensities and hence the implementation of the emotional lighting system. (paper)

Two-way visible light communication and illumination with LEDs

NARCIS (Netherlands)

Li, S.; Pandharipande, A.; Willems, F.M.J.

2017-01-01

Visible light communications (VLC) with light-emitting diodes (LEDs) has attracted applications, such as data communications, lighting control, and light interaction. In this paper, we propose a system by which two LED devices are used for two-way VLC while also providing illumination. We consider

Measurements of UGR of LED light by a DSLR colorimeter

Science.gov (United States)

Hsu, Shau-Wei; Chen, Cheng-Hsien; Jiaan, Yuh-Der

2012-10-01

We have developed an image-based measurement method on UGR (unified glare rating) of interior lighting environment. A calibrated DSLR (digital single-lens reflex camera) with an ultra wide-angle lens was used to measure the luminance distribution, by which the corresponding parameters can be automatically calculated. A LED lighting was placed in a room and measured at various positions and directions to study the properties of UGR. The testing results are fitted with visual experiences and UGR principles. To further examine the results, a spectroradiometer and an illuminance meter were respectively used to measure the luminance and illuminance at the same position and orientation of the DSLR. The calculation of UGR by this image-based method may solve the problem of non-uniform luminance-distribution of LED lighting, and was studied on segmentation of the luminance graph for the calculations.

Color adjustable LED driver design based on PWM

Science.gov (United States)

Du, Yiying; Yu, Caideng; Que, Longcheng; Zhou, Yun; Lv, Jian

2012-10-01

Light-emitting diode (LED) is a liquid cold source light source that rapidly develops in recent years. The merits of high brightness efficiency, long duration, high credibility and no pollution make it satisfy our demands for consumption and natural life, and gradually replace the traditional lamp-house-incandescent light and fluorescent light. However, because of the high cost and unstable drive circuit, the application range is restricted. To popularize the applications of the LED, we focus on improving the LED driver circuit to change this phenomenon. Basing on the traditional LED drive circuit, we adopt pre-setup constant current model and introduce pulse width modulation (PWM) control method to realize adjustable 256 level-grays display. In this paper, basing on human visual characteristics and the traditional PWM control method, we propose a new PWM control timing clock to alter the duty cycle of PWM signal to realize the simple gamma correction. Consequently, the brightness can accord with our visual characteristics.

Signal processing for LED lighting systems : illumination rendering and sensing

NARCIS (Netherlands)

Yang, H.

2010-01-01

Solid state lighting, employing high brightness light emitting diodes (LEDs), is becoming increasingly widely used. The advantages of LEDs include high radiative efficiency, long lifetime, limited heat generation and superior tolerance to humidity. Another important advantage of LED lighting systems

A summary of LED lighting impacts on health

Directory of Open Access Journals (Sweden)

Cosmin Ticleanu

2017-06-01

Full Text Available Lighting can affect the health of people in buildings. This goes beyond the safety aspects of providing enough illumination to see by; lighting affects mood and human circadian rhythms, while poor lighting can cause glare, headaches, eyestrain, aches and pains associated with poor body posture or, in extreme cases, skin conditions and various types of sight loss. These aspects ought to be considered by designers and building owners and occupiers in order to improve the lit environment and use adequate lighting and lighting controls that meet the recommendations of codes and standards. Various types of lighting can have different impacts depending on their spectral, optical and electrical characteristics. This paper discusses potential impacts of LED lighting on human health, and is based on a recent BRE review of research investigating the most typical effects of lighting on human health.

Ultrabroad linewidth orange-emitting nanowires LED for high CRI laser-based white lighting and gigahertz communications

KAUST Repository

Janjua, Bilal; Ng, Tien Khee; Zhao, Chao; Oubei, Hassan M.; Shen, Chao; Prabaswara, Aditya; Alias, Mohd Sharizal; Alhamoud, Abdullah Ali; Alatawi, Abdullah Awaad; Albadri, Abdulrahman M.; Alyamani, Ahmed Y.; El-Desouki, Munir M.; Ooi, Boon S.

2016-01-01

intensity- and bandwidth-tunable for high color-quality remained unexplored. In this paper, we present for the first time, the proof-of-concept of the generation of high-quality white light using an InGaN-based orange nanowires (NWs) LED grown on silicon

On-off switching patterns for smart LED lighting

NARCIS (Netherlands)

Linnartz, J.P.M.G.; Schenk, T.C.W.; Feri, L.; Yang, Hongming; Tjalkens, T.J.; Willems, F.M.J.

2009-01-01

This paper formulates a new communication problem for smart LED lighting sys tems designed for light effect control. It introduces the key requirements imposed on the design of the LED driving sequences, which include multiple access, arbi trary duty cycle and no disturbance caused on the normal

Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products, Part 3: LED Environmental Testing

Energy Technology Data Exchange (ETDEWEB)

Tuenge, Jason R.; Hollomon, Brad; Dillon, Heather E.; Snowden-Swan, Lesley J.

2013-03-01

This report covers the third part of a larger U.S. Department of Energy (DOE) project to assess the life-cycle environmental and resource impacts in the manufacturing, transport, use, and disposal of light-emitting diode (LED) lighting products in relation to incumbent lighting technologies. All three reports are available on the DOE website (www.ssl.energy.gov/tech_reports.html). • Part 1: Review of the Life-Cycle Energy Consumption of Incandescent, Compact Fluorescent and LED Lamps; • Part 2: LED Manufacturing and Performance; • Part 3: LED Environmental Testing. Parts 1 and 2 were published in February and June 2012, respectively. The Part 1 report included a summary of the life-cycle assessment (LCA) process and methodology, provided a literature review of more than 25 existing LCA studies of various lamp types, and performed a meta-analysis comparing LED lamps with incandescent and compact fluorescent lamps (CFLs). Drawing from the Part 1 findings, Part 2 performed a more detailed assessment of the LED manufacturing process and used these findings to provide a comparative LCA taking into consideration a wider range of environmental impacts. Both reports concluded that the life-cycle environmental impact of a given lamp is dominated by the energy used during lamp operation—the upstream generation of electricity drives the total environmental footprint of the product. However, a more detailed understanding of end-of-life disposal considerations for LED products has become increasingly important as their installation base has grown. The Part 3 study (reported herein) was undertaken to augment the LCA findings with chemical analysis of a variety of LED, CFL, and incandescent lamps using standard testing procedures. A total of 22 samples, representing 11 different models, were tested to determine whether any of 17 elements were present at levels exceeding California or Federal regulatory thresholds for hazardous waste. Key findings include: • The selected

Light out-coupling from LEDs by means of metal nanoparticles; Lichtauskopplung aus LEDs mittels Metallnanoteilchen

Energy Technology Data Exchange (ETDEWEB)

Goehler, Tino

2010-12-17

The external quantum efficiency of light-emitting diodes (LEDs) based on Al- GaAs/InGaAlP is limited by total internal reflection because of the high refractive index (typically between 3 and 4) of the semiconductor. Metal nanoparticles (MNP) deposited on the surface of the LED can be used as dipole scatterers in order to enhance the emission of the LED. In this thesis, first, single gold nanoparticles of various sizes deposited on such an LED were investigated. A clear enhancement is detected as long as the dipole plasmon resonance of the particle is at a shorter wavelength than the LED emission. If the plasmon resonance coincides with the LED emission or is at a larger wavelength, the enhancement turns into suppression. Numerical simulations indicate that this latter effect is mainly caused by the particle quadrupole resonance producing extra absorption. Arrays of MNPs can be produced by a special mask technique called ''Fischer pattern nanolithography'' and manipulated in shape and size by additional steps. Originally, the MNPs produced by this technique are triangular in shape and turn out to suppress the LED emission. After transformation of the particles to spheres, a clear enhancement was detected. Light that would otherwise remain trapped inside the substrate is coupled out by resonant plasmonic scattering. Investigations on analogous structures on a transparent high-index material (GaP) indicate a stronger coupling between the particles than expected on the basis of literature data. (orig.)

Fabrication of moth-eye structure on p-GaN layer of GaN-based LEDs for improvement of light extraction

International Nuclear Information System (INIS)

Hong, Eun-Ju; Byeon, Kyeong-Jae; Park, Hyoungwon; Hwang, Jaeyeon; Lee, Heon; Choi, Kyungwoo; Jung, Gun Young

2009-01-01

Moth-eye structures were produced on a p-GaN top cladding layer by UV imprint and inductively coupled plasma (ICP) etch processes in order to improve the light extraction efficiency of GaN-based green light-emitting diodes (LEDs). The height and shape of moth-eye structures were adjusted by controlling the thickness of Cr mask layer and ICP etching time. The transmittance of LED device stacks with moth-eye structure was increased up to 1.5-2.5 times, compared to identical LED sample without moth-eye structure and the intensity of photoluminescence from the InGaN multi-quantum well layer of LED sample with moth-eye structure was 5-7 times higher than that of the LED sample without the moth-eye structure.

Multi-band transmission color filters for multi-color white LEDs based visible light communication

Science.gov (United States)

Wang, Qixia; Zhu, Zhendong; Gu, Huarong; Chen, Mengzhu; Tan, Qiaofeng

2017-11-01

Light-emitting diodes (LEDs) based visible light communication (VLC) can provide license-free bands, high data rates, and high security levels, which is a promising technique that will be extensively applied in future. Multi-band transmission color filters with enough peak transmittance and suitable bandwidth play a pivotal role for boosting signal-noise-ratio in VLC systems. In this paper, multi-band transmission color filters with bandwidth of dozens nanometers are designed by a simple analytical method. Experiment results of one-dimensional (1D) and two-dimensional (2D) tri-band color filters demonstrate the effectiveness of the multi-band transmission color filters and the corresponding analytical method.

Design of an Oximeter Based on LED-LED Configuration and FPGA Technology

OpenAIRE

Stojanovic, Radovan; Karadaglic, Dejan

2013-01-01

A fully digital photoplethysmographic (PPG) sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED) for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA) is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (SpO2). The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (SpO2). N-LEDs...

Evaluation of OLED and edge-lit LED lighting panels

Science.gov (United States)

Mou, Xi; Narendran, Nadarajah; Zhu, Yiting; Freyssinier, Jean Paul

2016-09-01

Solid-state lighting (SSL) offers a new technology platform for lighting designers and end-users to illuminate spaces with low energy demand. Two types of SSL sources include organic light-emitting diodes (OLEDs) and light-emitting diodes (LEDs). OLED is an area light source, and its primary competing technology is the edge-lit LED panel. Generally, both of these technologies are considered similar in shape and appearance, but there is little understanding of how people perceive discomfort glare from large area light sources. The objective of this study was to evaluate discomfort glare for the two lighting technologies under similar operating conditions by gathering observers' reactions. The human factors study results showed no statistically significant difference in human response to discomfort glare between OLED and edge-lit LED panels when the two light sources produced the same lighting stimulus. This means both technologies appeared equally glary beyond a certain luminance.

Health risks occurring when color is percepted under led lighting

Directory of Open Access Journals (Sweden)

V.A. Kaptsov

2017-06-01

Full Text Available The article deals with problems of color perception under LED lighting. We revealed that inadequate perception of a signal color by a driver led to greater risks of transport accidents. We reviewed both Jung-Helmholtz three-color hypothesis and a modern one based on fiber-optical approach to functioning of "Mueller cells and cones" system. We made an attempt to explain a number of effects related to visibility curves and time delays when defining color of light signals. Our research on assessing influence exerted by LED lighting on functional state and working capacity of railway workers during which we applied occupational selection techniques revealed negative changes. We proved there was a decrease in functional resistance to color sense between red and green signals as well as longer response time for complicated sight-motor reaction and significant decrease in readiness to emergency actions (resistance to monotony in examined individuals. The article also contains data on time peculiarities which are characteristic for defining signals color in relation to red signal (650 nm. We showed that when red color LEDs with wave length much shorter than 650 nm were used in signaling devices it caused risks of inadequate color detection, longer reaction to inhibiting signals, and greater possibility of transport accidents and negative events in everyday life. These peculiarities should be taken into account when designing traffic lights and other signaling devices which provide transport safety. We also proved that signaling traffic lights for transport systems should be designed allowing for physiology of color perception by a human visual analyzer; application of LEDs with wave length shorter than 650 nm should be absolutely excluded

Innovations in LED lighting for reduced-ESM crop production in space

Science.gov (United States)

Massa, Gioia; Mitchell, Cary; Bourget, C. Michael; Morrow, Robert

In controlled-environment crop production such as will be practiced at the lunar outpost and Mars base, the single most energy-demanding aspect is electric lighting for plant growth, including energy costs for energizing lamps as well as for removing excess heat. For a variety of reasons, sunlight may not be a viable option as the main source of crop lighting off-Earth and traditional electric lamps for crop lighting have numerous drawbacks for use in a space environment. A collaborative research venture between the Advanced Life Support Crops Group at Purdue University and the Orbital Technologies Corporation (ORBITEC) has led to the development of efficient, reconfigurable LED lighting technologies for crop growth in an ALSS. The light sources use printed-circuit red and blue LEDs, which are individually tunable for a range of photosynthetic photon fluxes and photomorphogenic plant responses. Initial lighting arrays have LEDs that can be energized from the bottom upward when deployed in a vertical, intracanopy configuration, allowing the illumination to be tailored for stand height throughout the cropping cycle. Preliminary testing with the planophile crop cowpea (Vigna unguiculata L. Walp, breeding line IT87D-941-1), resulted in optimizing internal reflectance of growth compartments by lining walls, floor, and a movable ceiling with white Poly film, as well as by determining optimal planting density and plant positioning. Additionally, these light strips, called "lightsicles", can be configured into an overhead plane of light engines. When intracanopy and overhead-LED-lit cowpea crop production was compared, cowpea plants grown with intracanopy lighting had much greater understory leaf retention and produced more dry biomass per kilowatt-hour of lighting energy than did overhead-lit plants. The efficiency of light capture is reduced in overhead-lit scenarios due to mutual shading of lower leaves by upper leaves in closed canopies leading to premature abscission

Response of Eustoma Leaf Phenotype and Photosynthetic Performance to LED Light Quality

Directory of Open Access Journals (Sweden)

Md Zohurul Kadir Roni

2017-10-01

Full Text Available In a controlled environment, light from light-emitting diodes (LEDs has been associated with affecting the leaf characteristics of Eustoma. LEDs help plant growth and development, yet little is known about photosynthetic performance and related anatomical features in the early growth stage of Eustoma leaves. In this study, we examined the effects of blue (B, red (R, and white (W LEDs on the photosynthetic performance of Eustoma leaves, as well as leaf morphology and anatomy including epidermal layer thickness, palisade cells, and stomatal characteristics. Leaves grown under B LEDs were thicker and had a higher chlorophyll content than those grown under the R and W LEDs. Leaves under B LEDs had greater net photosynthetic rates (A, stomatal conductance (gs, and transpiration rates (E, especially at a higher photon flux density (PPFD, that resulted in a decrease in the intercellular CO2 concentration (Ci, than leaves under the W and R LEDs. B LEDs resulted in greater abaxial epidermal layer thickness and palisade cell length and width than the R and W LED treatments. The palisade cells also developed a more cylindrical shape in response to the B LEDs. B LED leaves also showed greater guard cell length, breadth, and area, and stomatal density, than W or R LEDs, which may contribute to increased A, gs and E at higher PPFDs.

Double-Grating Displacement Structure for Improving the Light Extraction Efficiency of LEDs

Directory of Open Access Journals (Sweden)

Zhibin Wang

2012-01-01

Full Text Available To improve the light extraction efficiency of light-emitting diodes (LEDs, grating patterns were etched on GaN and silver film surfaces. The grating-patterned surface etching enabled the establishment of an LED model with a double-grating displacement structure that is based on the surface plasmon resonance principle. A numerical simulation was conducted using the finite difference time domain method. The influence of different grating periods for GaN surface and silver film thickness on light extraction efficiency was analyzed. The light extraction efficiency of LEDs was highest when the grating period satisfied grating coupling conditions. The wavelength of the highest value was also close to the light wavelength of the medium. The plasmon resonance frequencies on both sides of the silver film were affected by silver film thickness. With increasing film thickness, plasmon resonance frequency tended toward the same value and light extraction efficiency reached its maximum. When the grating period for the GaN surface was 365 nm and the silver film thickness was 390 nm, light extraction efficiency reached a maximum of 55%.

Effects of melatonin injection or green-wavelength LED light on the antioxidant system in goldfish (Carassius auratus) during thermal stress.

Science.gov (United States)

Jung, Seo Jin; Choi, Young Jae; Kim, Na Na; Choi, Ji Yong; Kim, Bong-Seok; Choi, Cheol Young

2016-05-01

We tested the mitigating effects of melatonin injections or irradiation from green-wavelength light-emitting diodes (LEDs) on goldfish (Carassius auratus) exposed to thermal stress (high water temperature, 30 °C). The effects of the two treatments were assessed by measuring the expression and activity levels of the antioxidant enzymes, superoxide dismutase and catalase, plasma hydrogen peroxide, lipid hydroperoxide, and lysozyme. In addition, a comet assay was conducted to confirm that high water temperature damaged nuclear DNA. The expression and activity of the antioxidant enzymes, plasma hydrogen peroxide, and lipid hydroperoxide were significantly higher after exposure to high temperature and were significantly lower in fish that received melatonin or LED light than in those that received no mitigating treatment. Plasma lysozyme was significantly lower after exposure to high temperature and was significantly higher after exposure to melatonin or LED light. The comet assay revealed that thermal stress caused a great deal of damage to nuclear DNA; however, treatment with melatonin or green-wavelength LED light prevented a significant portion of this damage from occurring. These results indicate that, although high temperatures induce oxidative stress and reduce immune system strength in goldfish, both melatonin and green-wavelength LED light inhibit oxidative stress and boost the immune system. LED treatment increased the antioxidant and immune system activity more significantly than did melatonin treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Demonstration of a large-size horizontal light-field display based on the LED panel and the micro-pinhole unit array

Science.gov (United States)

Yang, Le; Sang, Xinzhu; Yu, Xunbo; Liu, Boyang; Liu, Li; Yang, Shenwu; Yan, Binbin; Du, Jingyan; Gao, Chao

2018-05-01

A 54-inch horizontal-parallax only light-field display based on the light-emitting diode (LED) panel and the micro-pinhole unit array (MPUA) is demonstrated. Normally, the perceived 3D effect of the three-dimensional (3D) display with smooth motion parallax and abundant light-field information can be enhanced with increasing the density of viewpoints. However, the density of viewpoints is inversely proportional to the spatial display resolution for the conventional integral imaging. Here, a special MPUA is designed and fabricated, and the displayed 3D scene constructed by the proposed horizontal light-field display is presented. Compared with the conventional integral imaging, both the density of horizontal viewpoints and the spatial display resolution are significantly improved. In the experiment, A 54-inch horizontal light-field display with 42.8° viewing angle based on the LED panel with the resolution of 1280 × 720 and the MPUA is realized, which can provide natural 3D visual effect to observers with high quality.

LEDWIRE: A Versatile Networking Platform for Smart LED Lighting Applications Using LIN-Bus and WSNs

Directory of Open Access Journals (Sweden)

Dimitrios D. Piromalis

2016-05-01

Full Text Available In this paper, the architecture of a versatile networking and control platform for Light-Emitting Diode (LED lighting applications is presented, based on embedded wireless and wired networking technologies. All the possible power and control signals distribution topologies of the lighting fixtures are examined with particular focus on dynamic lighting applications with design metrics as the cost, the required wiring installation expenses and maintenance complexity. The proposed platform is optimized for applications where the grouping of LED-based lighting fictures clusters is essential, as well as their synchronization. With such an approach, the distributed control and synchronization of LED lighting fixtures' clusters is performed through a versatile network that uses the single wire Local Interconnect Network (LIN bus. The proposed networking platform is presented in terms of its physical layer architecture, its data protocol configuration, and its functionality for smart control. As a proof of concept, the design of a LED lighting fixture together with a LIN-to-IEEE802.15.4/ZigBee data gateway is presented.

LED Context Lighting System in Residential Areas

Directory of Open Access Journals (Sweden)

Sook-Youn Kwon

2014-01-01

Full Text Available As issues of environment and energy draw keen interest around the globe due to such problems as global warming and the energy crisis, LED with high optical efficiency is brought to the fore as the next generation lighting. In addition, as the national income level gets higher and life expectancy is extended, interest in the enhancement of life quality is increasing. Accordingly, the trend of lightings is changing from mere adjustment of light intensity to system lighting in order to enhance the quality of one’s life as well as reduce energy consumption. Thus, this study aims to design LED context lighting system that automatically recognizes the location and acts of a user in residential areas and creates an appropriate lighting environment. The proposed system designed in this study includes three types of processing: first, the creation of a lighting environment index suitable for the user’s surroundings and lighting control scenarios and second, it measures and analyzes the optical characteristics that change depending on the dimming control of lighting and applies them to the index. Lastly, it adopts PIR, piezoelectric, and power sensor to grasp the location and acts of the user and create a lighting environment suitable for the current context.

Solid State pH Sensor Based on Light Emitting Diodes (LED As Detector Platform

Directory of Open Access Journals (Sweden)

Dermot Diamond

2006-08-01

Full Text Available A low-power, high sensitivity, very low-cost light emitting diode (LED-baseddevice developed for low-cost sensor networks was modified with bromocresol greenmembrane to work as a solid-state pH sensor. In this approach, a reverse-biased LEDfunctioning as a photodiode is coupled with a second LED configured in conventionalemission mode. A simple timer circuit measures how long (in microsecond it takes for thephotocurrent generated on the detector LED to discharge its capacitance from logic 1 ( 5 Vto logic 0 ( 1.7 V. The entire instrument provides an inherently digital output of lightintensity measurements for a few cents. A light dependent resistor (LDR modified withsimilar sensor membrane was also used as a comparison method. Both the LED sensor andthe LDR sensor responded to various pH buffer solutions in a similar way to obtainsigmoidal curves expected of the dye. The pKa value obtained for the sensors was found toagree with the literature value.

Fuselage mounted anti-collision lights utilizing high power LEDs

Science.gov (United States)

Lundberg, John; Machi, Nicolo; Mangum, Scott; Singer, Jeffrey

2005-09-01

As LEDs continue to improve in efficacy and total light output, they are increasingly finding their way in to new applications in the aviation industry as well as adjacent markets. One function that is particularly challenging and may reap substantial benefits from this new technology is the fuselage mounted anti-collision light. Anti-collision lights provide conspicuity for the aircraft by periodically emitting bright flashes of light. The color, light distribution and intensity levels for these lights are all closely regulated through Federal Aviation Regulation (FAR) documents. These lighting requirements, along with thermal, environmental and aerodynamic requirements, drive the overall design. In this paper, we will discuss the existing technologies used in anti-collision lights and the advantages and challenges associated with an LED solution. Particular attention will be given to the optical, thermal, electrical and aerodynamic aspects associated with an LED approach. A specific case study will be presented along with some of the challenges that have arisen during the design process. These challenges include the addition of an integrated covert anti-collision lighting.

Application of high-brightness LEDs in aircraft position lights

Science.gov (United States)

Machi, Nicolo; Mangum, Scott; Singer, Jeffrey M.

2004-10-01

Solid state lighting devices have made their way into a number of niche markets and continue to make inroads into other markets as their price / performance ratios improve. One of these markets is aviation lighting. Although this paper will focus on the use of LEDs for aircraft position lights, much of the discussion is applicable to other installations on the interior and exterior of the aircraft. The color, light distribution and intensity levels for a position light are all closely regulated through Code of Federal Regulation (CFR; formerly Federal Aviation Regulation (FAR)) documents. These lighting requirements, along with harsh thermal and environmental requirements, drive the design. In this paper, we will look at these requirements and discuss what is required in order to use LEDs for this type of application. We will explore the optical, thermal and electrical issues associated with the use of LEDs for position lights and examine the specific case study of the Astreon forward position lights. Finally, we will discuss some of the challenges that we see with solid state lighting in current and future aircraft applications.

LED Lighting in a Performing Arts Building

Energy Technology Data Exchange (ETDEWEB)

Miller, N. J.; Kaye, S. M. [Univ. of Florida, Gainesville, FL (United States); Coleman, P. M. [Univ. of Florida, Gainesville, FL (United States); Wilkerson, A. M.; Perrin, T. E.; Sullivan, G. P. [Efficiency Solutions, Inc., Richland, WA (United States)

2014-07-31

At the University of Florida in Gainesville, the DOE Solid-State Lighting GATEWAY program evaluated LED architectural and theatrical lighting in four academic/performance-related spaces within the Nadine McGuire Theatre + Dance Pavilion. Due to a wise choice of products and luminaire light distributions, the change brought significant quality improvements including improved controllability and color.

Feasibility of LED-Assisted CMOS Camera: Contrast Estimation for Laser Tattoo Treatment

Directory of Open Access Journals (Sweden)

Ngot Thi Pham

2018-04-01

Full Text Available Understanding the residual tattoo ink in skin after laser treatment is often critical for achieving good clinical outcomes. The current study aims to investigate the feasibility of a light-emitting diode (LED-assisted CMOS camera to estimate the relative variations in tattoo contrast after the laser treatment. Asian mice were tattooed using two color inks (black and red. The LED illumination was a separate process from the laser tattoo treatment. Images of the ink tattoos in skin were acquired under the irradiation of three different LED colors (red, green, and blue for pre- and post-treatment. The degree of contrast variation due to the treatment was calculated and compared with the residual tattoo distribution in the skin. The black tattoo demonstrated that the contrast consistently decreased after the laser treatment for all LED colors. However, the red tattoo showed that the red LED yielded an insignificant contrast whereas the green and blue LEDs induced a 30% (p < 0.001 and 26% (p < 0.01 contrast reduction between the treatment conditions, respectively. The proposed LED-assisted CMOS camera can estimate the relative variations in the image contrast before and after the laser tattoo treatment.

Beyond conventional c-plane GaN-based light emitting diodes: A systematic exploration of LEDs on semi-polar orientations

Science.gov (United States)

Monavarian, Morteza

Despite enormous efforts and investments, the efficiency of InGaN-based green and yellow-green light emitters remains relatively low, and that limits progress in developing full color display, laser diodes, and bright light sources for general lighting. The low efficiency of light emitting devices in the green-to-yellow spectral range, also known as the "Green Gap", is considered a global concern in the LED industry. The polar c-plane orientation of GaN, which is the mainstay in the LED industry, suffers from polarization-induced separation of electrons and hole wavefunctions (also known as the "quantum confined Stark effect") and low indium incorporation efficiency that are the two main factors that contribute to the Green Gap phenomenon. One possible approach that holds promise for a new generation of green and yellow light emitting devices with higher efficiency is the deployment of nonpolar and semi-polar crystallographic orientations of GaN to eliminate or mitigate polarization fields. In theory, the use of other GaN planes for light emitters could also enhance the efficiency of indium incorporation compared to c-plane. In this thesis, I present a systematic exploration of the suitable GaN orientation for future lighting technologies. First, in order to lay the groundwork for further studies, it is important to discuss the analysis of processes limiting LED efficiency and some novel designs of active regions to overcome these limitations. Afterwards, the choice of nonpolar orientations as an alternative is discussed. For nonpolar orientation, the (1100)-oriented (mo-plane) structures on patterned Si (112) and freestanding m-GaN are studied. The semi-polar orientations having substantially reduced polarization field are found to be more promising for light-emitting diodes (LEDs) owing to high indium incorporation efficiency predicted by theoretical studies. Thus, the semi-polar orientations are given close attention as alternatives for future LED technology

Current-voltage model of LED light sources

DEFF Research Database (Denmark)

Beczkowski, Szymon; Munk-Nielsen, Stig

2012-01-01

Amplitude modulation is rarely used for dimming light-emitting diodes in polychromatic luminaires due to big color shifts caused by varying magnitude of LED driving current and nonlinear relationship between intensity of a diode and driving current. Current-voltage empirical model of light...

[Study on the safety of blue light leak of LED].

Science.gov (United States)

Shen, Chong-Yu; Xu, Zheng; Zhao, Su-Ling; Huang, Qing-Yu

2014-02-01

In this paper, the blue light properties of LED illumination devices have been investigated. Against the status quo of China's LED lighting, we measured the spectrum component of LED lamps and analyzed the photobiological safety under the current domestic and international standards GB/T 20145-2006/CIE S009/E: 2002 and IEC62471: 2006 standards as well as CTL-0744_2009-laser resolution, which provides the reference to the manufacture of LED lighting lamps as well as related safety standards and laws. If the radiance intensity of blue light in LED is lower than 100 W x m(-2) x Sr(-1), there is no harm to human eyes. LEDs will not cause harm to human eyes under normal use, but we should pay attention to the protection of special populations (children), and make sure that they avoid looking at a light source for a long time. The research has found that the blue-rich lamps can affect the human rule of work and rest, and therefore, the LED lamps with color temperature below 4 000 K and color rendering index of 80 are suitable for indoor use. At the same time, the lamps with different parameters should be selected according to the different distances.

Stolephorus sp Behavior in Different LED (Light Emitting Diode) Color and Light Intensities

Science.gov (United States)

Fitri Aristi, D. P.; Ramadanita, I. A.; Hapsari, T. D.; Susanto, A.

2018-02-01

This research aims to observe anchovy (Stolephorus sp) behavior under different LED light intensities that affect eye physiology (cell cone structure). The materials used were Stolephorus sp taken from the waters off Jepara and 13 and 10 watt light emitting diode (LED). The research method was an experiment conducted from March through August 2015 in the waters off Jepara. Data analysis of visual histology and fish respond was carried out at the fishing gear material laboratory, anatomy and cultivate. Cone cell structure (mosaic cone) of Stolephorus sp forms a connected regular square pattern with every single cone surrounded by four double cones, which indicate that anchovies are sensitive to light. The 13 watt LED (628 lux) has faster response than the 10 watt LED (531 lux) as it has wider and higher emitting intensity, which also attracts fish to gather quicker.

Design of an Oximeter Based on LED-LED Configuration and FPGA Technology

Directory of Open Access Journals (Sweden)

Radovan Stojanovic

2013-01-01

Full Text Available A fully digital photoplethysmographic (PPG sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (SpO2. The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (SpO2. N-LEDs configuration is proposed for multichannel SpO2 measurements. The approach resulted in better spectral sensitivity, increased and adjustable resolution, reduced noise, small size, low cost and low power consumption.

Design of an oximeter based on LED-LED configuration and FPGA technology.

Science.gov (United States)

Stojanovic, Radovan; Karadaglic, Dejan

2013-01-04

A fully digital photoplethysmographic (PPG) sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED) for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA) is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (S(p)O(2)). The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (S(p)O(2)). N-LEDs configuration is proposed for multichannel S(p)O(2) measurements. The approach resulted in better spectral sensitivity, increased and adjustable resolution, reduced noise, small size, low cost and low power consumption.

Improvement of surface light extraction from flip-chip GaN-based LED by embossing of thermosetting polymers

Energy Technology Data Exchange (ETDEWEB)

Bao, Kui; Zhang, Bei; Wang, ZhiMin; Dai, Tao; Kang, XiangNing; Chen, ZhiZhong; Xu, Ke; Ji, Hang; Chen, Yong; Gan, ZiZhao [School of Physics and State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, Beijing 100871 (China)

2007-07-01

In this report, a further improvement of surface light extraction from flip-chip GaN-based LED was obtained by the micro patterning of encapsulation on the sapphire. The two dimensional taper arrays with period from 6 to 10 micron were successfully realized on polymer encapsulation by a simple and low cost technique so called embossing of thermosetting polymers. As a preliminary demonstration, at least 1.74 enhancement of the surface output intensity was achieved in the 1 mm x 1 mm GaN-based LED device under the injection current of 350 mA. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Light emitting diodes (LED): applications in forest and native plant nurseries

Science.gov (United States)

Thomas D. Landis; Jeremiah R. Pinto; R. Kasten Dumroese

2013-01-01

It was quotes like this that made us want to learn more about light emitting diodes (LED). Other than knowing that LEDs were the latest innovation in artificial lighting, we knew that we had a lot to learn. So we started by reviewing some of the basics. The following review is a brief synopsis of how light affects plants and some discussion about LED lighting. If you...

Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting at the I-35W Bridge, Minneapolis, MN

Energy Technology Data Exchange (ETDEWEB)

Kinzey, Bruce R.; Myer, Michael

2009-08-31

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology conducted in 2009 at the recently reconstructed I-35W bridge in Minneapolis, MN. The project was supported under the U.S. Department of Energy (DOE) Solid-State Lighting GATEWAY Technology Demonstration Program. Other participants in the demonstration project included the Minnesota Department of Transportation (Mn/DOT), Federal Highways Administration (FHWA), and BetaLED™ (a division of Ruud Lighting). Pacific Northwest National Laboratory (PNNL) conducted the measurements and analysis of the results. DOE has implemented a three-year evaluation of the LED luminaires in this installation in order to develop new longitudinal field data on LED performance in a challenging, real-world environment. This document provides information through the initial phase of the I-35W bridge project, up to and including the opening of the bridge to the public and the initial feedback received on the LED lighting installation from bridge users. Initial findings of the evaluation are favorable, with minimum energy savings level of 13% for the LED installation relative to the simulated base case using 250W high-pressure sodium (HPS) fixtures. The LEDs had an average illuminance level of 0.91 foot candles compared to 1.29 fc for the HPS lamps. The LED luminaires cost $38,000 more than HPS lamps, yielding a lengthy payback period, however the bridge contractor had offered to include the LED luminaires as part of the construction package at no additional cost. One potentially significant benefit of the LEDs in this installation is avoiding rolling lane closures on the heavily-traveled interstate bridge for the purpose of relamping the HPS fixtures. Rolling lane closures involve multiple crew members and various maintenance and safety vehicles, diversion of traffic, as well as related administrative tasks (e.g., approvals, scheduling, etc.). Mn/DOT records show an average cost of

Photobiocatalytic alcohol oxidation using LED light sources

NARCIS (Netherlands)

Rauch, M.C.R.; Schmidt, S.; Arends, I.W.C.E.; oppelt, K.; Kara, S; Hollmann, F.

2016-01-01

The photocatalytic oxidation of NADH using a flavin photocatalyst and a simple blue LED light source is reported. This in situ NAD+ regeneration system can be used to promote biocatalytic, enantioselective oxidation reactions. Compared to the traditional use of white light bulbs this method enables

Light-Emitting Diode-Based Illumination System for In Vitro Photodynamic Therapy

Directory of Open Access Journals (Sweden)

Defu Chen

2012-01-01

Full Text Available The aim of this study is to develop a light-emitting diode- (LED- based illumination system that can be used as an alternative light source for in vitro photodynamic therapy (PDT. This illumination system includes a red LED array composed of 70 LEDs centered at 643 nm, an air-cooling unit, and a specific-designed case. The irradiance as a function of the irradiation distance between the LED array and the sample, the homogeneity and stability of irradiation, and the effect of long-time irradiation on culture medium temperature were characterized. Furthermore, the survival rate of the CNE1 cells that sensitized with 5-aminolevulinic acid after PDT treatment was evaluated to demonstrate the efficiency of the new LED-based illumination system. The obtained results show that the LED-based illumination system is a promising light source for in vitro PDT that performed in standard multiwell plate.

Thermal, optical, and electrical engineering of an innovative tunable white LED light engine

Science.gov (United States)

Trivellin, Nicola; Meneghini, Matteo; Ferretti, Marco; Barbisan, Diego; Dal Lago, Matteo; Meneghesso, Gaudenzio; Zanoni, Enrico

2014-02-01

Color temperature, intensity and blue spectrum of the light affects the ganglion receptors in human brain stimulating the human nervous system. With this work we review different methods for obtaining tunable light emission spectra and propose an innovative white LED lighting system. By an in depth study of the thermal, electrical and optical characteristics of GaN and GaP based compound semiconductors for optoelectronics a specific tunable spectra has been designed. The proposed tunable white LED system is able to achieve high CRI (above 95) in a large CCT range (3000 - 5000K).

A new LED light source for display cases

DEFF Research Database (Denmark)

Dam-Hansen, Carsten; Petersen, Paul Michael

Abstract: We report a new LED light source suitable for illumination of gold objects. It has a variable correlated color temperature from 2760 K to 2200 K with a high color rendering index up to 97.......Abstract: We report a new LED light source suitable for illumination of gold objects. It has a variable correlated color temperature from 2760 K to 2200 K with a high color rendering index up to 97....

Nurse led, primary care based antiretroviral treatment versus hospital care: a controlled prospective study in Swaziland

Directory of Open Access Journals (Sweden)

Bailey Kerry A

2010-08-01

Full Text Available Abstract Background Antiretroviral treatment services delivered in hospital settings in Africa increasingly lack capacity to meet demand and are difficult to access by patients. We evaluate the effectiveness of nurse led primary care based antiretroviral treatment by comparison with usual hospital care in a typical rural sub Saharan African setting. Methods We undertook a prospective, controlled evaluation of planned service change in Lubombo, Swaziland. Clinically stable adults with a CD4 count > 100 and on antiretroviral treatment for at least four weeks at the district hospital were assigned to either nurse led primary care based antiretroviral treatment care or usual hospital care. Assignment depended on the location of the nearest primary care clinic. The main outcome measures were clinic attendance and patient experience. Results Those receiving primary care based treatment were less likely to miss an appointment compared with those continuing to receive hospital care (RR 0·37, p p = 0·001. Those receiving primary care based, nurse led care were more likely to be satisfied in the ability of staff to manage their condition (RR 1·23, p = 0·003. There was no significant difference in loss to follow-up or other health related outcomes in modified intention to treat analysis. Multilevel, multivariable regression identified little inter-cluster variation. Conclusions Clinic attendance and patient experience are better with nurse led primary care based antiretroviral treatment care than with hospital care; health related outcomes appear equally good. This evidence supports efforts of the WHO to scale-up universal access to antiretroviral treatment in sub Saharan Africa.

‘No Blue’ White LED

DEFF Research Database (Denmark)

Ou, Haiyan; Corell, Dennis Dan; Dam-Hansen, Carsten

2010-01-01

This paper explored the feasibility of making a white LED light source by color mixing method without using the blue color. This ‘no blue’ white LED has potential applications in photolithography room illumination, medical treatment and biophotonics research. A no-blue LED was designed......-2005. Even after 15 days of illumination, no effect was observed. So this LED-based solution was demonstrated to be a very promising light source for photolithography room illumination due to its better color rendering in addition to energy efficiency, long life time and design flexibility. Additionally......, and the prototype was fabricated. The spectral power distribution of both the LED bulb and the yellow fluorescent tube was measured. Based on that, colorimetric values were calculated and compared on terms of chromatic coordinates, correlated color temperature, color rendering index, and chromatic deviation...

Integrated Automotive High-Power LED-Lighting Systems in 3D-MID Technology

NARCIS (Netherlands)

Thomas, W.

2014-01-01

The growing energy consumption of lighting as well as rising luminous efficacies and -fluxes of high-power Light Emitting Diodes (LEDs) have contributed to the widespread use of LEDs in modern lighting systems. One of the most prominent users of the LED-technology is automotive (exterior) lighting.

A Complete MCDM Model for NPD Performance Assessment in an LED-Based Lighting Plant Factory

Directory of Open Access Journals (Sweden)

Wen-Chin Chen

2018-01-01

Full Text Available Globally, industries and economies have undergone rapid development and expansion over the last several decades. As a result, global warming and environmental contaminations have resulted in climate change and jeopardized food security. In many developing countries, already decreasing crop yields are threatened by extreme weather and soil damaged by genetically modified food, making environmental problems worse and increasing food and organic product prices. For these reasons, this study proposes a hybrid multicriteria decision-making (MCDM model for new product development (NPD in the light-emitting diode- (LED- based lighting plant factory. First, literature reviews and expert interviews are employed in constructing a list of decision-making objectives and criteria for new product development. Then, a fuzzy Delphi method (FDM is used to screen the elements of the objectives and criteria, while a fuzzy decision-making trial and evaluation laboratory (FDEMATEL is used to determine the relationships among the objectives and criteria. Finally, a fuzzy analytic network process (FANP and a composite priority vector (CPV are manipulated to determine the relative importance weights of the critical objectives and criteria. Results show that the proposed method can create a useful and assessable MCDM model for decision-making applications in new product development, and a case study is herein performed to validate the feasibility of the proposed model in a Taiwanese LED-based lighting plant factory, which not only provides the decision-makers with a feasible hierarchical data structure for decision-making guidance but also increases the competitive advantages of trade-offs on developing novel products.

LED-FISH: Fluorescence microscopy based on light emitting diodes for the molecular analysis of Her-2/neu oncogene amplification

Directory of Open Access Journals (Sweden)

Vollmer Ekkehard

2008-12-01

Full Text Available Abstract Light emitting diodes (LED, which are available as small monochromatic light sources with characteristic features such as maximum illumination power combined with minimum energy consumption and extremely long lifespan have already proved as a highly potential low-cost alternative for specific diagnostic applications in clinical medicine such as tuberculosis fluorescence microscopy. Likewise, the most reliable evaluation of Her-2/neu (c-erbB2 gene amplification, which has been established in the last few years for routine diagnosis in clinical pathology as determinant towards Herceptin-based treatment of patients with breast cancer, is based on fluorescence in situ hybridization (FISH and corresponding high priced fluorescence equipment. In order to test the possibility to utilize the advantages of low-cost LED technology on FISH analysis of c-erbB2 gene expression for routine diagnostic purposes, the applicability of a standard bright field Carl Zeiss Axiostar Plus microscope equipped with a Fraen AFTER* LED Fluorescence Microscope Kit for the detection of Her-2/neu gene signals was compared to an advanced Nikon Eclipse 80i fluorescence microscope in combination with a conventional 100W mercury vapor lamp. Both microscopes were fitted with the same Quicam FAST CCD digital camera to unequivocally compare the quality of the captured images. C-erbB2 gene expression was analyzed in 30 different human tissue samples of primary invasive breast cancer, following formalin fixation and subsequent paraffin-embedding. The Her2/neu gene signals (green were identifiable in the tumor cells in all cases and images of equal quality were captured under almost identical conditions by 480 nm (blue LED module equipped standard Axiostar microscope as compared to conventional fluorescence microscopy. In this first attempt, these monochromatic LED elements proved in principle to be suitable for the detection of Her-2/neu gene expression by FISH. Thus, our own

Development of Efficient UV-LED Phosphor Coatings for Energy Saving Solid State Lighting

International Nuclear Information System (INIS)

Uwe Happek

2006-01-01

The University of Georgia, in collaboration with GE Global Research, has investigated the relevant quenching mechanism of phosphor coatings used in white light devices based on UV LEDs. The final goal of the project was the design and fabrication of a high-efficacy white light UV-LED device through improved geometry and optimized phosphor coatings. At the end of the research period, which was extended to seamlessly carry over the research to a follow-up program, we have demonstrated a two-fold improvement in the conversion efficiency of a white light LED device, where the increase efficacy is due to both improved phosphor quantum efficiency and lamp geometry. Working prototypes have been displayed at DOE sponsored meetings and during the final presentation at the DOE Headquarters in Washington, DC. During the first phase of the project, a fundamental understanding of quenching processes in UV-LEDs was obtained, and the relationships that describe the performance of the phosphor as a function of photon flux, temperature, and phosphor composition were established. In the second phase of the project, these findings were then implemented to design the improved UV-LED lamp. In addition, our research provides a road map for the design of efficient white light LEDs, which will be an important asset during a follow-up project led by GE

LED lighting for greenhouses. Final report; LED belysning til vaeksthuse. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

OEstergaard, J.E. (Syddansk Univ. (SDU). Erhvervsinnovation og Teknologi, Odense (Denmark))

2011-01-15

The project had 3 main objectives: 1) To develop a prototype of a LED-based luminaire that can replace the existing glasshouse horticultural lighting. The project have developed a working prototype and experimentally replaced the traditional HPS luminaires in a controlled growing area. The project succeeded in producing plants of comparable quality. However, the project shows that the prototype can be improved by: x) being further integrated into the existing horticultural production technology (eg climate computers and purchase of electricity) x) adapting configuration of luminaires specifically to each plant variety x) adapting different cooling technologies to match specific customer needs x) In some cases being combined with heat input to optimize the overall economy. 2) To achieve an effective electricity savings of 50-80% - equivalent to a value of approx. DKK 5 million for a medium sized nursery. The verified electricity savings was 40%. In test setups and in well defined and controllable production areas the prototypes achieved electricity savings of > 50%. It is expected that a new generation of LEDs (Q3 2010) will allow for greater power savings. 3) To continue prototype development and initiate commercialization of the project through the company Fionia Lighting A/S. The shareholders of the company have allocated capital to the company to allow us to address the main challenges in commercializing the technology. It is expected that the company will enter a strategic alliance with a major industrial player in the beginning of 2011. (Author)

The study of LED light source illumination conditions for ideal algae cultivation

Science.gov (United States)

Tsai, Chun-Chin; Huang, Chien-Fu; Chen, Cin-Fu; Yue, Cheng-Feng

2017-02-01

Utilizing LED light source modules with 3 different RGB colors, the illumination effect of different wavelengths had been investigated on the growth curve of the same kind of micro algae. It was found that the best micro algae culturing status came out with long wavelength light such as red light (650 670 nm). Based on the same condition for a period of 3 weeks , the grown micro algae population density ratio represented by Optical Density (O.D.) ratio is 1?0.4?0.7 corresponding to growth with Red, Green, Blue light sources, respectively. Mixing 3 types and 2 types of LEDs with different parameters, the grown micro algae population densities were compared in terms of O.D. Interestingly enough, different light sources resulted in significant discoloration on micro algae growth, appearing yellow, brown, green, etc. Our experiments results showed such discoloration effect is reversible. Based on the same lighting condition, micro algae growth can be also affected by incubator size, nutrition supply, and temperature variation. In recent years, micro algae related technologies have been international wise a hot topic of energy and environmental protection for research and development institutes, and big energy companies among those developed countries. There will be an economically prosperous future. From this study of LED lighting to ideal algae cultivation, it was found that such built system would be capable of optimizing artificial cultivation system, leading to economic benefits for its continuous development. Since global warming causing weather change, accompanying with reducing energy sources and agriculture growth shortage are all threatening human being survival.

Study of LED modulation effect on the photometric quantities and beam homogeneity of automotive lighting

Science.gov (United States)

Koudelka, Petr; Hanulak, Patrik; Jaros, Jakub; Papes, Martin; Latal, Jan; Siska, Petr; Vasinek, Vladimir

2015-07-01

This paper discusses the implementation of a light emitting diode based visible light communication system for optical vehicle-to-vehicle (V2V) communications in road safety applications. The widespread use of LEDs as light sources has reached into automotive fields. For example, LEDs are used for taillights, daytime running lights, brake lights, headlights, and traffic signals. Future in the optical vehicle-to-vehicle (V2V) communications will be based on an optical wireless communication technology that using LED transmitter and a camera receiver (OCI; optical communication image sensor). Utilization of optical V2V communication systems in automotive industry naturally brings a lot of problems. Among them belongs necessity of circuit implementation into the current concepts of electronic LED lights control that allows LED modulation. These circuits are quite complicated especially in case of luxury cars. Other problem is correct design of modulation circuits so that final vehicle lightning using optical vehicle-to-vehicle (V2V) communication meets standard requirements on Photometric Quantities and Beam Homogeneity. Authors of this article performed research on optical vehicle-to-vehicle (V2V) communication possibilities of headlight (Jaguar) and taillight (Skoda) in terms of modulation circuits (M-PSK, M-QAM) implementation into the lamp concepts and final fulfilment of mandatory standards on Photometric Quantities and Beam Homogeneity.

Light outputs of LED with various refractive indices and geometrical structures of encapsulants

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyung-Tae [Chosun University, Gwangju (Korea, Republic of); Jo, Kyoung-Woo; Hwang, Jung-Ha; Kwon, Ho-Ki [LG Innotek Co., Ltd., Seoul (Korea, Republic of); Park, Si-Hyun [Yeungnam University, Gyeongsan (Korea, Republic of)

2010-12-15

In this paper we present the results of experiments and simulations for the light output power from LEDs for various refractive indices and the geometrical structures of the LED encapsulants. InGaN-based LED chips were fabricated and were bonded in Ag reflector cups within polyphthalamide (PPA) chip carriers; then, encapsulants with various refractive indices and the geometrical structures were fabricated onto them by using a dispensing method. The light output power with the encapsulant was shown to increase with the refractive index of the encapsulant materials in the case of a spherical encapsulant while it decreased in the case of a flat geometry encapsulant. We performed ray tracing simulations for the LED light output and confirmed that the simulation results were consistent with our experimentally measured results. In addition, the light output with the encapsulant rapidly increased with the sidewall angle of the chip carrier in the case of the flat encapsulant while it was not affected by the sidewall angle, remaining constant, in the case of the spherical geometry.

Light outputs of LED with various refractive indices and geometrical structures of encapsulants

International Nuclear Information System (INIS)

Kim, Kyung-Tae; Jo, Kyoung-Woo; Hwang, Jung-Ha; Kwon, Ho-Ki; Park, Si-Hyun

2010-01-01

In this paper we present the results of experiments and simulations for the light output power from LEDs for various refractive indices and the geometrical structures of the LED encapsulants. InGaN-based LED chips were fabricated and were bonded in Ag reflector cups within polyphthalamide (PPA) chip carriers; then, encapsulants with various refractive indices and the geometrical structures were fabricated onto them by using a dispensing method. The light output power with the encapsulant was shown to increase with the refractive index of the encapsulant materials in the case of a spherical encapsulant while it decreased in the case of a flat geometry encapsulant. We performed ray tracing simulations for the LED light output and confirmed that the simulation results were consistent with our experimentally measured results. In addition, the light output with the encapsulant rapidly increased with the sidewall angle of the chip carrier in the case of the flat encapsulant while it was not affected by the sidewall angle, remaining constant, in the case of the spherical geometry.

Evaluation of Uniformity and Glare Improvement with Low Energy Efficiency Losses in Street Lighting LED Luminaires Using Laser-Sintered Polyamide-Based Diffuse Covers

Directory of Open Access Journals (Sweden)

Alfonso Gago-Calderón

2018-04-01

Full Text Available Energy saving in street lighting is garnering more interest and has become a priority in municipal management. Therefore, LED luminaires are gradually becoming prevalent in our cities. Beyond their energy/economic saving potential, quality in public lighting installations concerns aspects such as uniformity and glare which must be maintained if not improved in any installation renewal project using this technology. The high light intensity generated in a discrete point in LED packages and its directional nature result in significant deficiencies in these last two parameters. To soften these effects, translucent covers are being used as one of the most common solutions with the drawback of significant light intensity losses. The objective of this paper is to evaluate the behavior of LED luminaire’s polyamide-based optical covers manufactured with a laser-sintered process. These are designed to improve glare and uniformity output, to minimize light output reductions, and to be industrially manufactured with no increment of cost for their lighting equipment compared to conventional transparent polycarbonate solutions. A laboratory and field lighting test study has been applied to different covers with the same LED lamp and luminaire to compare the performance of three different solutions built with different polymeric materials and with different light transmission surface textures. The photometric results have been observed and discussed to demonstrate the ability to significantly improve the lighting performance of LED luminaires—illuminance and uniformity levels and discomfort and disability glare indexes— using an improved optic cover.

Blue laser diode (LD) and light emitting diode (LED) applications

International Nuclear Information System (INIS)

Bergh, Arpad A.

2004-01-01

The family of blue LEDs, edge emitting and surface emitting lasers, enable a number of applications. Blue lasers are used in digital applications such as optical storage in high density DVDs. The resolution of the spot size and hence the storage density is diffraction limited and is inversely proportional to the square of the wavelength of the laser. Other applications include printing, optical scanners, and high-resolution photo-lithography. As light emitters, blue LEDs are used for signaling and in direct view large area emissive displays. They are also making inroads into signage and LCD back-lighting, mobile platforms, and decorative accent lighting in curtains, furniture, etc. Blue LEDs produce white light either with phosphor wavelength converters or in combination with red and green LEDs. The full potential of LED light sources will require three devices to enable complete control over color and intensity. Sensing and medical/bio applications have a major impact on home security, on monitoring the environment, and on health care. New emerging diagnostic and therapeutic applications will improve the quality and reduce the cost of health care. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Blue laser diode (LD) and light emitting diode (LED) applications

Energy Technology Data Exchange (ETDEWEB)

Bergh, Arpad A [Optoelectronics Industry Development Association (OIDA), 1133 Connecticut Avenue, NW, Suite 600, Washington, DC 20036-4329 (United States)

2004-09-01

The family of blue LEDs, edge emitting and surface emitting lasers, enable a number of applications. Blue lasers are used in digital applications such as optical storage in high density DVDs. The resolution of the spot size and hence the storage density is diffraction limited and is inversely proportional to the square of the wavelength of the laser. Other applications include printing, optical scanners, and high-resolution photo-lithography. As light emitters, blue LEDs are used for signaling and in direct view large area emissive displays. They are also making inroads into signage and LCD back-lighting, mobile platforms, and decorative accent lighting in curtains, furniture, etc. Blue LEDs produce white light either with phosphor wavelength converters or in combination with red and green LEDs. The full potential of LED light sources will require three devices to enable complete control over color and intensity. Sensing and medical/bio applications have a major impact on home security, on monitoring the environment, and on health care. New emerging diagnostic and therapeutic applications will improve the quality and reduce the cost of health care. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Nanorods on surface of GaN-based thin-film LEDs deposited by post-annealing after photo-assisted chemical etching

Science.gov (United States)

Chen, Lung-Chien; Lin, Wun-Wei; Liu, Te-Yu

2017-01-01

This study investigates the optoelectronic characteristics of gallium nitride (GaN)-based thin-film light-emitting diodes (TF-LEDs) that are formed by a two-step transfer process that involves wet etching and post-annealing. In the two-step transfer process, GaN LEDs were stripped from sapphire substrates by the laser lift-off (LLO) method using a KrF laser and then transferred onto ceramic substrates. Ga-K nanorods were formed on the surface of the GaN-based TF-LEDs following photo-assisted chemical etching and photo-enhanced post-annealing at 100 °C for 1 min. As a result, the light output power of GaN-based TF-LEDs with wet etching and post-annealing was over 72% more than that of LEDs that did not undergo these treatments.

Trapping of Rift Valley Fever (RVF vectors using Light Emitting Diode (LED CDC traps in two arboviral disease hot spots in Kenya

Directory of Open Access Journals (Sweden)

Tchouassi David P

2012-05-01

Full Text Available Abstract Background Mosquitoes’ response to artificial lights including color has been exploited in trap designs for improved sampling of mosquito vectors. Earlier studies suggest that mosquitoes are attracted to specific wavelengths of light and thus the need to refine techniques to increase mosquito captures following the development of super-bright light-emitting diodes (LEDs which emit narrow wavelengths of light or very specific colors. Therefore, we investigated if LEDs can be effective substitutes for incandescent lamps used in CDC light traps for mosquito surveillance, and if so, determine the best color for attraction of important Rift Valley Fever (RFV vectors. Methods The efficiency of selected colored LED CDC light traps (red, green, blue, violet, combination of blue-green-red (BGR to sample RVF vectors was evaluated relative to incandescent light (as control in a CDC light trap in two RVF hotspots (Marigat and Ijara districts in Kenya. In field experiments, traps were baited with dry ice and captures evaluated for Aedes tricholabis, Ae. mcintoshi, Ae. ochraceus, Mansonia uniformis, Mn. africana and Culex pipiens, following Latin square design with days as replicates. Daily mosquito counts per treatment were analyzed using a generalized linear model with Negative Binomial error structure and log link using R. The incidence rate ratios (IRR that mosquito species chose other treatments instead of the control, were estimated. Results Seasonal preference of Ae.mcintoshi and Ae. ochraceus at Ijara was evident with a bias towards BGR and blue traps respectively in one trapping period but this pattern waned during another period at same site with significantly low numbers recorded in all colored traps except blue relative to the control. Overall results showed that higher captures of all species were recorded in control traps compared to the other LED traps (IRR  Conclusion Based on our trapping design and color, none of the LEDs

Light extraction efficiency enhancement for fluorescent SiC based white light-emitting diodes

DEFF Research Database (Denmark)

Ou, Haiyan; Ou, Yiyu; Argyraki, Aikaterini

Fluorescent SiC based white light-emitting diodes(LEDs) light source, as an innovative energy-efficient light source, would even have longer lifetime, better light quality and eliminated blue-tone effect, compared to the current phosphor based white LED light source. In this paper, the yellow...

A self-calibrating led-based solar test platform

DEFF Research Database (Denmark)

Krebs, Frederik C; Sylvester-Hvid, Kristian O.; Jørgensen, Mikkel

2011-01-01

A compact platform for testing solar cells is presented. The light source comprises a multi-wavelength high-power LED (light emitting diode) array allowing the homogenous illumination of small laboratory solar cell devices (substrate size 50 × 25 mm) within the 390–940 nm wavelength range......, it is possible to perform all the commonly employed measurements on the solar cell at very high speed without moving the sample. In particular, the LED-based illumination system provides an alternative to light-biased incident photon-to-current efficiency measurement to be performed which we demonstrate. Both...

Design method of freeform light distribution lens for LED automotive headlamp based on DMD

Science.gov (United States)

Ma, Jianshe; Huang, Jianwei; Su, Ping; Cui, Yao

2018-01-01

We propose a new method to design freeform light distribution lens for light-emitting diode (LED) automotive headlamp based on digital micro mirror device (DMD). With the Parallel optical path architecture, the exit pupil of the illuminating system is set in infinity. Thus the principal incident rays of micro lens in DMD is parallel. DMD is made of high speed digital optical reflection array, the function of distribution lens is to distribute the emergent parallel rays from DMD and get a lighting pattern that fully comply with the national regulation GB 25991-2010.We use DLP 4500 to design the light distribution lens, mesh the target plane regulated by the national regulation GB 25991-2010 and correlate the mesh grids with the active mirror array of DLP4500. With the mapping relations and the refraction law, we can build the mathematics model and get the parameters of freeform light distribution lens. Then we import its parameter into the three-dimensional (3D) software CATIA to construct its 3D model. The ray tracing results using Tracepro demonstrate that the Illumination value of target plane is easily adjustable and fully comply with the requirement of the national regulation GB 25991-2010 by adjusting the exit brightness value of DMD. The theoretical optical efficiencies of the light distribution lens designed using this method could be up to 92% without any other auxiliary lens.

Daylight integrated illumination control of LED systems based on enhanced presence sensing

NARCIS (Netherlands)

Pandharipande, A.; Caicedo Fernandez, D.R.

2011-01-01

Light emitting diodes (LEDs) are considered to become the dominant source of illumination in the future, offering long life times, energy efficiency and flexible tunability. The flexibility of adapting LED parameters offers multiple degrees of freedom in designing LED based lighting systems. In this

Effect of LED lighting on the cooling and heating loads in office buildings

International Nuclear Information System (INIS)

Ahn, Byung-Lip; Jang, Cheol-Yong; Leigh, Seung-Bok; Yoo, Seunghwan; Jeong, Hakgeun

2014-01-01

Highlights: • Application of heat control strategy reduces total energy consumption of LED lighting. • Convective heat from LED lighting should be emitted outdoors during cooling period. • Seasonal optimization of convective heat lowers total energy consumption. - Abstract: LED lighting has the potential to provide energy savings, and in many countries, there are policies to encourage its use owing to its higher efficiency and longer life in comparison to other lighting fixtures. However, since 75–85% of the light electric power in LED lights is still generated as heat, the sole use of LED lighting in a building could have a negative effect on the cooling load. In this paper, we study the heating properties of LED lighting and establish a management strategy to exploit these properties to reduce the energy used for heating and cooling of buildings. Using a simulation program, the energy consumption of the Green Building in Daejeon, Korea, and the virtual building provided by the U.S. Department of Energy (DOE) was computed according for different light fixtures. A control strategy is more applicable to LED lighting than to general fluorescent lighting, especially for the cooling of a building, because the use of a return-air duct and the heat sinks on the LED fixtures allow the heat to be better directed. Deployment of LED lights in combination with such a control strategy can help to increase the energy efficiency of a building

Demonstration Assessment of Light-Emitting Diode (LED) Parking Lot Lighting in Leavenworth, KS

Energy Technology Data Exchange (ETDEWEB)

Myer, Michael; Kinzey, Bruce R.; Curry, Ku' uipo

2011-05-06

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a commercial parking lot lighting application, under the U.S. Department of Energy (DOE) Solid-State Lighting Technology GATEWAY Demonstration Program. The parking lot is for customers and employees of a Walmart Supercenter in Leavenworth, Kansas and this installation represents the first use of the LED Parking Lot Performance Specification developed by the DOE’s Commercial Building Energy Alliance. The application is a parking lot covering more than a half million square feet, lighted primarily by light-emitting diodes (LEDs). Metal halide wall packs were installed along the building facade. This site is new construction, so the installed baseline(s) were hypothetical designs. It was acknowledged early on that deviating from Walmart’s typical design would reduce the illuminance on the site. Walmart primarily uses 1000W pulse-start metal halide (PMH) lamps. In order to provide a comparison between both typical design and a design using conventional luminaires providing a lower illuminance, a 400W PMH design was also considered. As mentioned already, the illuminance would be reduced by shifting from the PMH system to the LED system. The Illuminating Engineering Society of North America (IES) provides recommended minimum illuminance values for parking lots. All designs exceeded the recommended illuminance values in IES RP-20, some by a wider margin than others. Energy savings from installing the LED system compared to the different PMH systems varied. Compared to the 1000W PMH system, the LED system would save 63 percent of the energy. However, this corresponds to a 68 percent reduction in illuminance as well. In comparison to the 400W PMH system, the LED system would save 44 percent of the energy and provide similar minimum illuminance values at the time of relamping. The LED system cost more than either of the PMH systems when comparing initial costs

LED-based UV source for monitoring spectroradiometer properties

Science.gov (United States)

Sildoja, Meelis-Mait; Nevas, Saulius; Kouremeti, Natalia; Gröbner, Julian; Pape, Sven; Pendsa, Stefan; Sperfeld, Peter; Kemus, Fabian

2018-06-01

A compact and stable UV monitoring source based on state-of-the-art commercially available ultraviolet light emitting diodes (UV-LEDs) has been developed. It is designed to trace the radiometric stability—both responsivity and wavelength scale—of array spectroradiometers measuring direct solar irradiance in the wavelength range between 300 nm and 400 nm. The spectral irradiance stability of the UV-LED-based light source observed in the laboratory after seasoning (burning-in) the individual LEDs was better than 0.3% over a 12 h period of continuous operation. The integral irradiance measurements of the source over a period of several months, where the UV-LED source was not operated continuously between the measurements, showed stability within 0.3%. In-field measurements of the source with an array spectroradiometer indicated the stability of the source to be within the standard uncertainty of the spectroradiometer calibration, which was within 1% to 2%.

DESIGNING CLIENT OF ANDROID-BASED LED INTELLIGENT LIGHTING SYSTEM AND ITS IMPLEMENTATION%基于 Android 的 LED 智能照明系统客户端的设计与实现

Institute of Scientific and Technical Information of China (English)

胡艳蕊; 宋开新; 秦会斌; 张明准

2016-01-01

To get rid of the way of controlling home lighting with traditional mechanical switches and to make full use of the advantages of smart phones and other mobile equipment resources,we proposed the Android-based LED intelligent lighting systems,and designed and developed the Android-based client of LED intelligent lighting system.We used WiFi to control home lighting equipment,it can not only control the on and off,timing,dimming and colouring of individual light and lights group,but can also select and edit different lighting effects in scene patterns according to the needs of different environments,as well as can dynamically add new lights through code scanning. Moreover,in intelligent light control module we called the China Weather Network API interface and the phone built-in light sensor to automatically control the colour and brightness of the light,the function advertising has also been added to the client.We tested the client system and the lighting module in a wireless network environment,the feasibility and practicality of the LED intelligent lighting system client has been proven.%为了摆脱用传统机械式开关控制家居照明的方式，充分利用智能手机等移动设备资源，提出基于 Android 的 LED 智能照明系统，设计开发基于 Android 的 LED 智能照明系统客户端。利用 WiFi 控制家居照明设备，不仅可以控制单个灯和各组灯的开关、定时、调光和调色，而且可以根据对不同环境的需求在情景模式中选择和编辑不同的灯光效果，还可以通过扫码动态添加新灯等。并且在智能光控模块中调用了中国天气网 API 接口和手机自带的光线传感器来自动调节灯光的颜色和亮度，该客户端还增加了广告功能。把该客户端系统和灯具模块放在无线网络环境中进行测试，验证了该 LED 智能照明系统客户端的可行性和实用性。

Developing Quantum Dot Phosphor-Based Light-Emitting Diodes for Aviation Lighting Applications

International Nuclear Information System (INIS)

Wu, F.; Dawei, Z.; Shuzhen, S.; Yiming, Z.; Songlin, Z.; Jian, X.

2012-01-01

We have investigated the feasibility of employing quantum dot (QD) phosphor-based light-emitting diodes (LEDs) in aviation applications that request Night Vision Imaging Systems (NVIS) compliance. Our studies suggest that the emerging QD phosphor-based LED technology could potentially be superior to conventional aviation lighting technology by virtue of the marriage of tight spectral control and broad wavelength tunability. This largely arises from the fact that the optical properties of semiconductor nano crystal QDs can be tailored by varying the nano crystal size without any compositional changes. It is envisioned that the QD phosphor-based LEDs hold great potentials in cockpit illumination, back light sources of monitor screens, as well as the LED indicator lights of aviation panels.

Raman study of the effect of LED light on grafted bone defects

Science.gov (United States)

Soares, Luiz G. G. P.; Aciole, Jouber M. S.; Aciole, Gilbeth T. S.; Barbosa, Artur F. S.; Silveira-Júnior, Landulfo; Pinheiro, Antônio L. B.

2013-03-01

Benefits of the isolated or combined use light and biomaterials on bone healing have been suggested. Our group has used several models to assess the effects of laser on bone. A Raman spectral analysis on surgical bone defects grafted or not with Hydroxyapatite (HA), treated or not with LED was carried out. 40 rats were divided into 4 groups. On Group I the defect was filled with the clot. On Group II, the defect was filled with the HA. On groups III the defect was filled with Clot and further irradiated with LED and on group IV the defects was filled with the HA and further irradiated with LED. LED (λ850 +/- 10nm, 150mW, A= 0.5cm2, 68s, 20 J/cm2 per session, 140 J/cm2 per treatment) was applied at 48 h intervals during 15 days. Specimens were taken after 15 and 30 days after surgery and kept on liquid nitrogen, and underwent Raman analysis. For this, the peak of hydroxyapatite (~960 cm-1) was used as marker of bone mineralization. Significant difference was observed at both times (p<0.05). When the biomaterial was used higher peaks were observed. Association with LED further improved the intensity. Conclusion: It is concluded that LED light improved the effect of the HA.

A color management system for multi-colored LED lighting

DEFF Research Database (Denmark)

Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen

2015-01-01

A new color control system is described and implemented for a five–color LED light engine, covering a wide white gamut. The system combines a new way of using pre-calibrated look-up tables and a rule-based optimization of chromaticity distance from the Planckian locus with a calibrated color sensor....... The color sensor monitors the chromaticity of the mixed light providing the correction factor for the current driver by using the generated look-up table. The long term stability and accuracy of the system will be experimentally investigated with target tolerance within a circle radius 0.0011 in the uniform...

Interior LED Lighting Technology. Navy Energy Technology Validation (Techval) Program

Science.gov (United States)

2015-09-01

usually on most of the time. • Consider replacing existing CFL, high-intensity discharge (HID), or halogen lamp light fixtures/ lamps with LED fixtures... lamps . What is the Technology? An LED is a semiconductor-diode that emits light when power is applied. A driver is used, much as a ballast, to...available in integrated luminaires that can be used to replace existing luminaires. LEDs are also available as direct replacement lamps for many

LED; Zum Thema LED

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

This collection of articles on the subject of light emitting diodes (LED) provides technical information on LED technology, examines latest developments and provides examples of LED use in practice. An 'ABC' of LED technology is presented and fifteen common LED mistakes are noted. The chances and risks of LED use are discussed as is the retrofitting of lighting installations with LEDs. The use of LEDs in street lighting is examined. The journal also includes interviews with architects and a lighting designer. Practical examples of the use of LEDs include the refurbished parliamentary library in Berne, their use in the bird sanctuary headquarters in Sempach, Switzerland, as well as LED use in sales outlets. Also, the use of LED lighting in a spa gazebo in Lucerne is examined.

Comparative Study of Lettuce and Radish Grown Under Red and Blue Light-Emitting Diodes (LEDs) and White Fluorescent Lamps

Science.gov (United States)

Mickens, Matthew A.

2012-01-01

Growing vegetable crops in space will be an essential part of sustaining astronauts during long-term missions. To drive photosynthesis, red and blue light-emitting diodes (LEDs) have attracted attention because of their efficiency, longevity, small size, and safety. In efforts to optimize crop production, there have also been recent interests in analyzing the subtle effects of green light on plant growth, and to determine if it serves as a source of growth enhancement or suppression. A comparative study was performed on two short cycle crops of lettuce (Outredgeous) and radish (Cherry Bomb) grown under two light treatments. The first treatment being red and blue LEDs, and the second treatment consisting of white fluorescent lamps which contain a portion of green light. In addition to comparing biomass production, physiological characterizations were conducted on how the light treatments influence morphology, water use, chlorophyll content, and the production of A TP within plant tissues.

Progress and prospects of GaN-based LEDs using nanostructures

Science.gov (United States)

Zhao, Li-Xia; Yu, Zhi-Guo; Sun, Bo; Zhu, Shi-Chao; An, Ping-Bo; Yang, Chao; Liu, Lei; Wang, Jun-Xi; Li, Jin-Min

2015-06-01

Progress with GaN-based light emitting diodes (LEDs) that incorporate nanostructures is reviewed, especially the recent achievements in our research group. Nano-patterned sapphire substrates have been used to grow an AlN template layer for deep-ultraviolet (DUV) LEDs. One efficient surface nano-texturing technology, hemisphere-cones-hybrid nanostructures, was employed to enhance the extraction efficiency of InGaN flip-chip LEDs. Hexagonal nanopyramid GaN-based LEDs have been fabricated and show electrically driven color modification and phosphor-free white light emission because of the linearly increased quantum well width and indium incorporation from the shell to the core. Based on the nanostructures, we have also fabricated surface plasmon-enhanced nanoporous GaN-based green LEDs using AAO membrane as a mask. Benefitting from the strong lateral SP coupling as well as good electrical protection by a passivation layer, the EL intensity of an SP-enhanced nanoporous LED was significantly enhanced by 380%. Furthermore, nanostructures have been used for the growth of GaN LEDs on amorphous substrates, the fabrication of stretchable LEDs, and for increasing the 3-dB modulation bandwidth for visible light communication. Project supported by the National Natural Science Foundation of China (Grant No. 61334009), the National High Technology Research and Development Program of China (Grant Nos. 2015AA03A101 and 2014BAK02B08), China International Science and Technology Cooperation Program (Grant No. 2014DFG62280), the “Import Outstanding Technical Talent Plan” and “Youth Innovation Promotion Association Program” of the Chinese Academy of Sciences.

Time Effectiveness of Ultraviolet C Light (UVC Emitted by Light Emitting Diodes (LEDs in Reducing Stethoscope Contamination

Directory of Open Access Journals (Sweden)

Gabriele Messina

2016-09-01

Full Text Available Today it is well demonstrated that stethoscopes can be as contaminated as hands, which are a recognized source of Health-Care Associated Infections (HCAIs. Ultraviolet C (UVC light has proven disinfection capacity and the innovative UVC technology of Light Emitting Diode (LED shows several potential benefits. To verify whether the use of UVC LEDs is effective and reliable in stethoscope membrane disinfection after prolonged use, a pre-post intervention study was conducted. A total of 1668 five-minute cycles were performed on two UVC LEDs to simulate their use; thereafter, their disinfection capacity was tested on stethoscope membranes used on a previously auscultated volunteer. Then, a further 1249 cycles were run and finally the LEDs were tested to assess performance in reducing experimental contamination by Staphylococcus aureus, Pseudomonas aeruginosa and Escherichia coli on the stethoscope membrane. Baseline volunteer contamination identified 104 Colony Forming Units (CFUs while treated Petri dishes had 12 and 15 CFUs (p < 0.001. Statistically significant differences (p < 0.001 were also found relating to the reduction of specific bacteria: in particular, after treatment no CFU were observed for S. aureus and E. coli. UVC LEDs demonstrated the capacity to maintain high levels of disinfection after more than 240 h of use and they were effective against common microorganisms that are causative agents of HCAIs.

Time Effectiveness of Ultraviolet C Light (UVC) Emitted by Light Emitting Diodes (LEDs) in Reducing Stethoscope Contamination.

Science.gov (United States)

Messina, Gabriele; Fattorini, Mattia; Nante, Nicola; Rosadini, Daniele; Serafini, Andrea; Tani, Marco; Cevenini, Gabriele

2016-09-23

Today it is well demonstrated that stethoscopes can be as contaminated as hands, which are a recognized source of Health-Care Associated Infections (HCAIs). Ultraviolet C (UVC) light has proven disinfection capacity and the innovative UVC technology of Light Emitting Diode (LED) shows several potential benefits. To verify whether the use of UVC LEDs is effective and reliable in stethoscope membrane disinfection after prolonged use, a pre-post intervention study was conducted. A total of 1668 five-minute cycles were performed on two UVC LEDs to simulate their use; thereafter, their disinfection capacity was tested on stethoscope membranes used on a previously auscultated volunteer. Then, a further 1249 cycles were run and finally the LEDs were tested to assess performance in reducing experimental contamination by Staphylococcus aureus, Pseudomonas aeruginosa and Escherichia coli on the stethoscope membrane. Baseline volunteer contamination identified 104 Colony Forming Units (CFUs) while treated Petri dishes had 12 and 15 CFUs (p < 0.001). Statistically significant differences (p < 0.001) were also found relating to the reduction of specific bacteria: in particular, after treatment no CFU were observed for S. aureus and E. coli. UVC LEDs demonstrated the capacity to maintain high levels of disinfection after more than 240 h of use and they were effective against common microorganisms that are causative agents of HCAIs.

Effects of melatonin and green-wavelength LED light on the physiological stress and immunity of goldfish, Carassius auratus, exposed to high water temperature.

Science.gov (United States)

Jung, Seo Jin; Kim, Na Na; Choi, Young Jae; Choi, Ji Yong; Choi, Young-Ung; Heo, Youn Seong; Choi, Cheol Young

2016-10-01

This study investigated the effects of increasing water temperature (22-30 °C) on the physiological stress response and immunity of goldfish, Carassius auratus, and the ability of green light-emitting diode (LED) irradiation or melatonin injections to mitigate this temperature-induced stress. To evaluate the effects of either green-wavelength LED light or melatonin on stress in goldfish, we measured plasma triiodothyronine (T3), thyroxine (T4), and thyroid hormone receptor (TR) mRNA expression; plasma cortisol and glucose; and immunoglobulin M (IgM) and lysozyme mRNA expression. The thyroid hormone activities, TR mRNA expression, and plasma cortisol and glucose were higher in goldfish exposed to high-temperature water, but were lower after exposure to melatonin or green-wavelength LED light. Lysozyme mRNA expression and plasma IgM activity and protein expression were lower after exposure to high water temperatures and higher after melatonin or green-wavelength LED light treatments. Therefore, high water temperature induced stress and decreased immunity; however, green-wavelength LED light and melatonin treatments mitigated the effects of stress and enhanced immunity. The benefits of melatonin decreased with time, whereas those of green-wavelength LED treatment did not.

Universal fixture design for body mounted LED lights

Science.gov (United States)

Hajra, Debdyut

2017-09-01

Today LED headlamps, armbands and ankle-bands, shoe-lights etc. have become very popular. These find extensive use in search and rescue operations, mining, carving, etc. and are also used by individuals during hiking, trekking, running, etc. during dark hours. They serve two main purposes: they provide sufficient illumination in low light conditions and they are used to indicate the presence of a person after dark. These have the same basic requirements. They must produce sufficient light, have high durability, long battery life, must be light weight and energy efficient. This paper discusses possibilities of designing a universal LED fixture can be designed so that it meets the respective needs of everyone irrespective of their background and industry. It discusses the materials to be used for its different body parts, innovative clip design for attachment with support structures like head and armbands, helmets, shoes, etc.

A high-performance stand-alone solar PV power system for LED lighting

KAUST Repository

Huang, B. J.

2010-06-01

The present study developed a high-performance solar PV power technology for the LED lighting of a solar home system. The nMPPO (near-Maximum-Power- Point- Operation) design is employed in system design to eliminate MPPT. A feedback control system using pulse width modulation (PWM) technique was developed for battery charging control which can increase the charging capacity by 78%. For high-efficiency lighting, the LED is directly driven by battery using a PWM discharge control to eliminate a DC/DC converter. Two solar-powered LED lighting systems (50W and 100W LED) were built. The long-term outdoor tests have shown that the loss of load probability for full-night lighting requirement is zero for 50W LED and 3.6% for 100W LED. © 2010 IEEE.

LEDs light up the world

Energy Technology Data Exchange (ETDEWEB)

Mather, N.

2004-06-30

A lighting system using light-emitting diodes, and privately financed by a Canadian engineering professor at the University of Calgary, has been set up in a village in Nepal in 2000. Since then, through the efforts of the 'Light Up The World' Foundation, established by Dr. Irvine-Halliday, projects have lit up thousands of homes in the Philippines, India, Afghanistan, the Galapagos Islands, Mexico, Sri Lanka, and Angola. Although the goal of the project is primarily to provide lighting for reading and writing for school-children, the project has been the source of many other advantages; creation of enterprise, increased employment, enhanced income, gender equality, and improvements in health and safety among them. Since LED lamps in most cases replace kerosene lamps, the system also has significant environmental benefits. The system as originally envisioned creates electricity by pedal-powered generator, or by solar panels connected to a battery, depending on what is available at each home. Each home is connected to the power supply and supplied with low-energy diode lamps. The lights are extremely efficient and many homes can be equipped with them using less energy than it takes to power a single 100-watt light bulb. 5 photos.

Developing Quantum Dot Phosphor-Based Light-Emitting Diodes for Aviation Lighting Applications

Directory of Open Access Journals (Sweden)

Fengbing Wu

2012-01-01

Full Text Available We have investigated the feasibility of employing quantum dot (QD phosphor-based light-emitting diodes (LEDs in aviation applications that request Night Vision Imaging Systems (NVIS compliance. Our studies suggest that the emerging QD phosphor-based LED technology could potentially be superior to conventional aviation lighting technology by virtue of the marriage of tight spectral control and broad wavelength tunability. This largely arises from the fact that the optical properties of semiconductor nanocrystal QDs can be tailored by varying the nanocrystal size without any compositional changes. It is envisioned that the QD phosphor-based LEDs hold great potentials in cockpit illumination, back light sources of monitor screens, as well as the LED indicator lights of aviation panels.

Newly patented process enables low-cost solution for increasing white light spectrum of LEDs

Science.gov (United States)

Spanard, Jan-Marie

2017-10-01

A newly patented process for completing the spectral light array emitted by LED bulbs provides a low-cost method for producing better human centered lighting (HCL). This process uses non-luminescent colorant filters, filling out the jagged LED spectral emission into a full, white light array. While LED bulbs have the distinct economic advantages of using less energy, producing less heat and lasting years longer than traditional incandescent bulbs, the persistent metameric failure of LED bulbs has resulted in slower, and sometimes reluctant, adoption of LED lighting by the residential, retail and architectural markets. Adding missing wavelengths to LED generated bulbs via colorant filters increases the aesthetic appeal of the light by decreasing current levels of metameric failure, reducing the `flatness', `harshness', and `dullness' of LED generated light reported by consumers. LED phosphor-converted light can be successfully tuned to "whiter" white light with selective color filtering using permanent, durable transparent pigments. These transparent pigments are selectively applied in combination with existing manufacturing technologies and utilized as a final color-tuning step in bulb design. The quantity of emitted light chosen for color filtering can be adjusted from 1% to 100% of emitted light, creating a custom balance of light quantity with light quality. This invention recognizes that "better light" is frequently chosen over "more light" in the consumer marketplace.

Performance of GaN-Based LEDs with Nanopatterned Indium Tin Oxide Electrode

Directory of Open Access Journals (Sweden)

Zhanxu Chen

2016-01-01

Full Text Available The indium tin oxide (ITO has been widely applied in light emitting diodes (LEDs as the transparent current spreading layer. In this work, the performance of GaN-based blue light LEDs with nanopatterned ITO electrode is investigated. Periodic nanopillar ITO arrays are fabricated by inductive coupled plasma etching with the mask of polystyrene nanosphere. The light extraction efficiency (LEE of LEDs can be improved by nanopatterned ITO ohmic contacts. The light output intensity of the fabricated LEDs with nanopatterned ITO electrode is 17% higher than that of the conventional LEDs at an injection current of 100 mA. Three-dimensional finite difference time domain simulation matches well with the experimental result. This method may serve as a practical approach to improving the LEE of the LEDs.

Off-grid energy services for the poor: Introducing LED lighting in the Millennium Villages Project in Malawi

International Nuclear Information System (INIS)

Adkins, Edwin; Eapen, Sandy; Kaluwile, Flora; Nair, Gautam; Modi, Vijay

2010-01-01

Lanterns that use light-emitting diodes (LEDs) powered by batteries, which are in turn charged by grid electricity or small solar panels, have emerged as a cost-competitive alternative to kerosene and other fuel-based lighting technologies, offering brighter light for longer duration at equal or lower cost over time. This paper presents lessons learned from the introduction of solar LED lanterns in rural Malawi. We discuss a market-based program using new and existing local commercial structures such as vendors and cooperatives to sell lanterns to village households without subsidy. The paper addresses issues of enterprise development, community interactions, and survey data on lighting use and expenditure patterns before and after LED lantern introduction. Households that purchased a lantern reported high levels of satisfaction with the LED lanterns as well as savings in annual kerosene expenditure comparable to the price of the lantern. These households also reported monthly incomes comparable to the price of the LED lanterns whereas non-adopters surveyed reported monthly incomes about half this level, suggesting a need for financing options to maximize adoption among poorer populations in rural areas. These results suggest that similar market based models of LED lighting technology dissemination have the potential to be replicated and scaled up in other off-grid regions in developing countries. However, viability of local cooperatives and supply chains for lantern products over the medium-to-long term remain to be assessed.

Improvement of quantum efficiency in green light-emitting diodes with pre-TMIn flow treatment

International Nuclear Information System (INIS)

Lee, Ya-Ju; Chen, Yi-Ching; Lu, Tien-Chang

2011-01-01

The effects of pre-trimethlyindium (TMIn) flow on the improved electrical characteristics and highly stable temperature properties of InGaN green light-emitting diodes (LEDs) are discussed. For the LED sample with a pre-TMIn flow treatment, the tunnelling of injected carriers associated with threading defects is significantly reduced, which promotes the diffusion-recombination of injected carriers, as well as the overall emission efficiency of the LED. In addition, the pre-TMIn flow treatment evidently reduces the dependence of external quantum efficiency on temperature and efficiency droop of green LEDs. As a result, we conclude that the pre-TMIn flow treatment is a promising scheme for the improvement of output performance of InGaN-based green LEDs.

A long distance voice transmission system based on the white light LED

Science.gov (United States)

Tian, Chunyu; Wei, Chang; Wang, Yulian; Wang, Dachi; Yu, Benli; Xu, Feng

2017-10-01

A long distance voice transmission system based on a visible light communication technology (VLCT) is proposed in the paper. Our proposed system includes transmitter, receiver and the voice signal processing of single chip microcomputer. In the compact-sized LED transmitter, we use on-off-keying and not-return-to-zero (OOK-NRZ) to easily realize high speed modulation, and then systematic complexity is reduced. A voice transmission system, which possesses the properties of the low-noise and wide modulation band, is achieved by the design of high efficiency receiving optical path and using filters to reduce noise from the surrounding light. To improve the speed of the signal processing, we use single chip microcomputer to code and decode voice signal. Furthermore, serial peripheral interface (SPI) is adopted to accurately transmit voice signal data. The test results of our proposed system show that the transmission distance of this system is more than100 meters with the maximum data rate of 1.5 Mbit/s and a SNR of 30dB. This system has many advantages, such as simple construction, low cost and strong practicality. Therefore, it has extensive application prospect in the fields of the emergency communication and indoor wireless communication, etc.

Analysis of Shade Matching in Natural Dentitions Using Intraoral Digital Spectrophotometer in LED and Filtered LED Light Sources.

Science.gov (United States)

Chitrarsu, Vijai Krishnan; Chidambaranathan, Ahila Singaravel; Balasubramaniam, Muthukumar

2017-10-31

To evaluate the shade matching capabilities in natural dentitions using Vita Toothguide 3D-Master and an intraoral digital spectrophotometer (Vita Easyshade Advance 4.0) in various light sources. Participants between 20 and 40 years old with natural, unrestored right maxillary central incisors, no history of bleaching, orthodontic treatment, or malocclusion and no rotations were included. According to their shades, subjects were randomly selected and grouped into A1, A2, and A3. A total of 100 participants (50 male and 50 female) in each group were chosen for this study. Shade selection was made between 10 am and 2 pm for all light sources. The same examiner selected the shade of natural teeth with Vita Toothguide 3D-Master under natural light within 2 minutes. Once the Vita Toothguide 3D-Masterwas matched with the maxillary right central incisor, the L*, a*, and b* values, chroma, and hue were recorded with Vita Easyshade Advance 4.0 by placing it on the shade tab under the same light source. The values were statistically analyzed using one-way ANOVA and Tukey's HSD post hoc test with SPSS v22.0 software. The mean ∆E* ab values for shades A1, A2, and A3 for groups 1, 2, and 3 were statistically significantly different from each other (p spectrophotometer showed statistically significant differences in shade matching compared to Vita Toothguide 3D-Master. Incandescent light showed more accurate shade matching than the filtered LED, LED, and daylight. © 2017 by the American College of Prosthodontists.

LED-Based High-Voltage Lines Warning System

Directory of Open Access Journals (Sweden)

Eldar MUSA

2013-04-01

Full Text Available LED-based system, running with the current of high-voltage lines and converting the current flowing through the line into the light by using a toroid transformer, has been developed. The transformer’s primary winding is constituted by the high voltage power line. Toroidal core consists of two equal parts and the secondary windings are evenly placed on these two parts. The system is mounted on the high-voltage lines as a clamp. The secondary winding ends are connected in series by the connector on the clamp. LEDs are supplied by the voltage at the ends of secondary. Current flowing through highvoltage transmission lines is converted to voltage by the toroidal transformer and the light emitting LEDs are supplied with this voltage. The theory of the conversion of the current flowing through the line into the light is given. The system, running with the current of the line and converting the current into the light, has been developed. System has many application areas such as warning high voltage lines (warning winches to not hinder the high-voltage lines when working under the lines, warning planes to not touch the high-voltage lines, remote measurement of high-voltage line currents, and local illumination of the line area

The health risks associated with energy efficient fluorescent, LEDs, and artificial lighting

Science.gov (United States)

Panahi, Allen

2014-09-01

With the phasing out of incandescent lamps in many countries, the introduction of new LED based light sources and luminaries sometimes raise the question of whether the spectral characteristics of the LED and other energy savings Fluorescent lights including the popular CFLs are suitable to replace the traditional incandescent lamps. These concerns are sometimes raised particularly for radiation emissions in the UV and Blue parts of the spectrum. This paper aims to address such concerns for the common `white light' sources typically used in household and other general lighting used in the work place. Recent studies have shown that women working the night shift have an increased probability of developing breast cancer. We like to report on the findings of many studies done by medical professionals, in particular the recent announcement of AMA in the US and many studies conducted in the UK, as well as the European community to increase public awareness on the long term health risks of the optical and opto-biological effects on the human health caused by artificial lighting.

An Investigation of LED Street Lighting's Impact on Sky Glow

Energy Technology Data Exchange (ETDEWEB)

Kinzey, Bruce R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Perrin, Tess E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Miller, Naomi J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kocifaj, Miroslav [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Aube, Martin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lamphar, Hector A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-04-25

A significant amount of public attention has recently focused on perceived impacts of converting street lighting from incumbent lamp-based products to LED technology. Much of this attention pertains to the higher content of short wavelength light (commonly referred to as "blue light") of LEDs and its attendant influences on sky glow (a brightening of the night sky that can interfere with astronomical observation and may be associated with a host of other issues). The complexity of this topic leads to common misunderstandings and misperceptions among the public, and for this reason the U.S. Department of Energy Solid-State Lighting Program embarked on a study of sky glow using a well-established astronomical model to investigate some of the primary factors influencing sky glow. This report details the results of the investigation and attempts to present those results in terms accessible to the general lighting community. The report also strives to put the results into a larger context, and help educate interested readers on various topics relevant to the issues being discussed.

Effect of LED light quality on in vitro shoot proliferation and growth of ...

African Journals Online (AJOL)

As an alternative to conventional lighting systems, light emitting diode (LED) has been ... The objective of this study was to determine the effects of different LED light quality on ... Key words: Light quality, micropropagation, orchid, chlorophyll.

Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market

Energy Technology Data Exchange (ETDEWEB)

Tracy, Jennifer; Jacobson, Arne; Mills, Evan

2010-03-02

Low cost rechargeable flashlights that use LED technology are increasingly available in African markets. While LED technology holds promise to provide affordable, high quality lighting services, the widespread dissemination of low quality products may make it difficult to realize this potential. This study includes performance results for three brands of commonly available LED flashlights that were purchased in Kenya in 2009. The performance of the flashlights was evaluated by testing five units for each of the three brands. The tests included measurements of battery capacity, time required to charge the battery, maximum illuminance at one meter, operation time and lux-hours from a fully charged battery, light distribution, and color rendering. All flashlights tested performed well below the manufacturers? rated specifications; the measured battery capacity was 30-50percent lower than the rated capacity and the time required to fully charge the battery was 6-25percent greater than the rated time requirement. Our analysis further shows that within each brand there is considerable variability in each performance indicator. The five samples within a single brand varied from each other by as much as 22percent for battery capacity measurements, 3.6percent for the number of hours required for a full charge, 23percent for maximum initial lux, 38percent for run time, 11percent for light distribution and by as much as 200percent for color rendering. Results obtained are useful for creating a framework for quality assurance of off-grid LED products and will be valuable for informing consumers, distributors and product manufacturers about product performance.

High-power LED light sources for optical measurement systems operated in continuous and overdriven pulsed modes

Science.gov (United States)

Stasicki, Bolesław; Schröder, Andreas; Boden, Fritz; Ludwikowski, Krzysztof

2017-06-01

The rapid progress of light emitting diode (LED) technology has recently resulted in the availability of high power devices with unprecedented light emission intensities comparable to those of visible laser light sources. On this basis two versatile devices have been developed, constructed and tested. The first one is a high-power, single-LED illuminator equipped with exchangeable projection lenses providing a homogenous light spot of defined diameter. The second device is a multi-LED illuminator array consisting of a number of high-power LEDs, each integrated with a separate collimating lens. These devices can emit R, G, CG, B, UV or white light and can be operated in pulsed or continuous wave (CW) mode. Using an external trigger signal they can be easily synchronized with cameras or other devices. The mode of operation and all parameters can be controlled by software. Various experiments have shown that these devices have become a versatile and competitive alternative to laser and xenon lamp based light sources. The principle, design, achieved performances and application examples are given in this paper.

Biomass and pigments production in photosynthetic bacteria wastewater treatment: effects of light sources.

Science.gov (United States)

Zhou, Qin; Zhang, Panyue; Zhang, Guangming

2015-03-01

This study is aimed at enhancing biomass and pigments production together with pollution removal in photosynthetic bacteria (PSB) wastewater treatment via different light sources. Red, yellow, blue, white LED and incandescent lamp were used. Results showed different light sources had great effects on the PSB. PSB had the highest biomass production, COD removal and biomass yield with red LED. The corresponding biomass, COD removal and biomass yield reached 2580 mg/L, 88.6% and 0.49 mg-biomass/mg-COD-removal, respectively. The hydraulic retention time of wastewater treatment could be shortened to 72 h with red LED. Mechanism analysis showed higher ATP was produced with red LED than others. Light sources could significantly affect the pigments production. The pigments productions were greatly higher with LED than incandescent lamp. Yellow LED had the highest pigments production while red LED produced the highest carotenoid/bacteriochlorophyll ratio. Considering both efficiency and energy cost, red LED was the optimal light source. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hybrid sunlight/LED illumination and renewable solar energy saving concepts for indoor lighting.

Science.gov (United States)

Tsuei, Chih-Hsuan; Sun, Wen-Shing; Kuo, Chien-Cheng

2010-11-08

A hybrid method for using sunlight and light-emitting diode (LED) illumination powered by renewable solar energy for indoor lighting is simulated and presented in this study. We can illuminate an indoor space and collect the solar energy using an optical switching system. When the system is turned off, the full spectrum of the sunlight is concentrated by a concentrator, to be absorbed by solar photovoltaic devices that provide the electricity to power the LEDs. When the system is turned on, the sunlight collected by the concentrator is split into visible and non-visible rays by a beam splitter. The visible rays pass through the light guide into a light box where it is mixed with LED light to ultimately provide uniform illumination by a diffuser. The non-visible rays are absorbed by the solar photovoltaic devices to provide electrical power for the LEDs. Simulation results show that the efficiency of the hybrid sunlight/LED illumination with the renewable solar energy saving design is better than that of LED and traditional lighting systems.

Direct battery-driven solar LED lighting using constant-power control

KAUST Repository

Huang, Bin-Juine

2012-11-01

A direct battery-driven LED lighting technique using constant-power control is proposed in the present study. A system dynamics model of LED luminaire was derived and used in the design of the feedback constant-power control system. The test result has shown that the power of 18. W and 100. W LED luminaires can be controlled accurately with error at 2-5%. A solar LED street lighting system using constant-power and dimming control was designed and built for field test in a remote area. The long-term performance was satisfactory and no any failure since the installation. Since no high-power capacitor is used in the present constant-power control circuit, a longer lifetime is expected. © 2012 Elsevier Ltd.

Practical, reliable and inexpensive assay of lycopene in tomato products based on the combined use of light emitting diode (LED) and the optothermal window

NARCIS (Netherlands)

Bicanic, D.D.; Cuypers, R.; Luterotti, S.; Sporec, M.; Zoppi, A.; Vugec, J.

2008-01-01

Light emitting diode (LED) combined with the concept of optothermal window (OW) is proposed as a new approach (LED-OW) to detect lycopene in a wide range of tomato-based products (tomato juice, tomato ketchup, tomato passata and tomato puree). Phytonutrient lycopene is a dominant antioxidant in

Projecting LED product life based on application

Science.gov (United States)

Narendran, Nadarajah; Liu, Yi-wei; Mou, Xi; Thotagamuwa, Dinusha R.; Eshwarage, Oshadhi V. Madihe

2016-09-01

LED products have started to displace traditional light sources in many lighting applications. One of the commonly claimed benefits for LED lighting products is their long useful lifetime in applications. Today there are many replacement lamp products using LEDs in the marketplace. Typically, lifetime claims of these replacement lamps are in the 25,000-hour range. According to current industry practice, the time for the LED light output to reach the 70% value is estimated according to IESNA LM-80 and TM-21 procedures and the resulting value is reported as the whole system life. LED products generally experience different thermal environments and switching (on-off cycling) patterns when used in applications. Current industry test methods often do not produce accurate lifetime estimates for LED systems because only one component of the system, namely the LED, is tested under a continuous-on burning condition without switching on and off, and because they estimate for only one failure type, lumen depreciation. The objective of the study presented in this manuscript was to develop a test method that could help predict LED system life in any application by testing the whole LED system, including on-off power cycling with sufficient dwell time, and considering both failure types, catastrophic and parametric. The study results showed for the LED A-lamps tested in this study, both failure types, catastrophic and parametric, exist. The on-off cycling encourages catastrophic failure, and maximum operating temperature influences the lumen depreciation rate and parametric failure time. It was also clear that LED system life is negatively affected by on-off switching, contrary to commonly held belief. In addition, the study results showed that most of the LED systems failed catastrophically much ahead of the LED light output reaching the 70% value. This emphasizes the fact that life testing of LED systems must consider catastrophic failure in addition to lumen depreciation, and

A Simulation-Based LED Design Project in Photonics Instruction Based on Industry-University Collaboration

Science.gov (United States)

Chang, S. -H.; Chen, M. -L.; Kuo, Y. -K.; Shen, Y. -C.

2011-01-01

In response to the growing industrial demand for light-emitting diode (LED) design professionals, based on industry-university collaboration in Taiwan, this paper develops a novel instructional approach: a simulation-based learning course with peer assessment to develop students' professional skills in LED design as required by industry as well as…

Savings in Cooling Energy with a Thermal Management System for LED Lighting in Office Buildings

Directory of Open Access Journals (Sweden)

Byung-Lip Ahn

2015-06-01

Full Text Available Light-emitting diode (LED lighting should be considered for lighting efficiency enhancement, however, waste heat from light-emitting diode (LED lighting increases the internal cooling load during the summer season. In order to solve this problem we propose a thermal management system for light-emitting diode (LED lighting with a heat exchanger module integrated with the building’s heating, ventilation, and air conditioning (HVAC system to move the lighting’s waste heat outdoors. An experiment was carried out to investigate the thermal effects in a test chamber and the heat exchange rate between the heat sink and the duct air. The heat generated by the light-emitting diode (LED lighting was calculated as 78.1% of light-emitting diode (LED input power and the heat exchange rate of the lighting heat exchange module was estimated to be between 86.5% and 98.1% according to the light-emitting diode (LED input power and the flow rate of air passing the heat sink. As a result, the average light-emitting diode (LED lighting heat contribution rate for internal heat gain was determined as 0.05; this value was used to calculate the heating and cooling energy demand of the office building through an energy simulation program. In the simulation results, the cooling energy demand was reduced by 19.2% compared with the case of conventionally installed light-emitting diode (LED lighting.

Spectral matching research for light-emitting diode-based neonatal jaundice therapeutic device light source

Science.gov (United States)

Gan, Ruting; Guo, Zhenning; Lin, Jieben

2015-09-01

To decrease the risk of bilirubin encephalopathy and minimize the need for exchange transfusions, we report a novel design for light source of light-emitting diode (LED)-based neonatal jaundice therapeutic device (NJTD). The bilirubin absorption spectrum in vivo was regarded as target. Based on spectral constructing theory, we used commercially available LEDs with different peak wavelengths and full width at half maximum as matching light sources. Simple genetic algorithm was first proposed as the spectral matching method. The required LEDs number at each peak wavelength was calculated, and then, the commercial light source sample model of the device was fabricated to confirm the spectral matching technology. In addition, the corresponding spectrum was measured and the effect was analyzed finally. The results showed that fitted spectrum was very similar to the target spectrum with 98.86 % matching degree, and the actual device model has a spectrum close to the target with 96.02 % matching degree. With higher fitting degree and efficiency, this matching algorithm is very suitable for light source matching technology of LED-based spectral distribution, and bilirubin absorption spectrum in vivo will be auspicious candidate for the target spectrum of new LED-based NJTD light source.

Fundamentals of solid-state lighting LEDs, OLEDs, and their applications in illumination and displays

CERN Document Server

Khanna, Vinod Kumar

2014-01-01

History and Basics of LightingChronological History of LightingLearning Objectives How Early Man Looked at the ""Sun"" The Need for Artificial Light Sources First Steps in the Evolution of Artificial Lighting The First Solid-State Lighting Device The First Practical Electrical Lighting Device The Incandescent Filament Lamp Mercury and Sodium Vapor Lamps The Fluorescent Lamp The Compact Fluorescent Lamp Revolution in the World of Lighting: Advent of Light-Emitting Diodes Birth of the First LED and the Initial Stages of LED Development The Father of the LED: Holonyak Jr. The Post-1962 Developmen

Design and fabrication of adjustable red-green-blue LED light arrays for plant research

Directory of Open Access Journals (Sweden)

Kenitz J Dustin

2005-08-01

Full Text Available Abstract Background Although specific light attributes, such as color and fluence rate, influence plant growth and development, researchers generally cannot control the fine spectral conditions of artificial plant-growth environments. Plant growth chambers are typically outfitted with fluorescent and/or incandescent fixtures that provide a general spectrum that is accommodating to the human eye and not necessarily supportive to plant development. Many studies over the last several decades, primarily in Arabidopsis thaliana, have clearly shown that variation in light quantity, quality and photoperiod can be manipulated to affect growth and control developmental transitions. Light emitting diodes (LEDs has been used for decades to test plant responses to narrow-bandwidth light. LEDs are particularly well suited for plant growth chambers, as they have an extraordinary life (about 100,000 hours, require little maintenance, and use negligible energy. These factors render LED-based light strategies particularly appropriate for space-biology as well as terrestrial applications. However, there is a need for a versatile and inexpensive LED array platform where individual wavebands can be specifically tuned to produce a series of light combinations consisting of various quantities and qualities of individual wavelengths. Two plans are presented in this report. Results In this technical report we describe the practical construction of tunable red-green-blue LED arrays to support research in plant growth and development. Two light fixture designs and corresponding circuitry are presented. The first is well suited for a laboratory environment for use in a finite area with small plants, such as Arabidopsis. The second is expandable and appropriate for growth chambers. The application of these arrays to early plant developmental studies has been validated with assays of hypocotyl growth inhibition/promotion and phototropic curvature in Arabidopsis seedlings

LED Light to improve Strawberry Flavour, Quality and Production

NARCIS (Netherlands)

Hanenberg, M.A.A.; Janse, J.; Verkerke, W.

2016-01-01

A current demonstration in the greenhouses of Wageningen UR in Bleiswijk (the Netherlands) shows positive results of LED light on the quality and production of strawberries (Fragaria x ananassa). In this demonstration two strawberry cultivars, Elsanta and Sonata, are exposed to three different light

Uniformity of LED light illumination in application to direct imaging lithography

Science.gov (United States)

Huang, Ting-Ming; Chang, Shenq-Tsong; Tsay, Ho-Lin; Hsu, Ming-Ying; Chen, Fong-Zhi

2016-09-01

Direct imaging has widely applied in lithography for a long time because of its simplicity and easy-maintenance. Although this method has limitation of lithography resolution, it is still adopted in industries. Uniformity of UV irradiance for a designed area is an important requirement. While mercury lamps were used as the light source in the early stage, LEDs have drawn a lot of attention for consideration from several aspects. Although LED has better and better performance, arrays of LEDs are required to obtain desired irradiance because of limitation of brightness for a single LED. Several effects are considered that affect the uniformity of UV irradiance such as alignment of optics, temperature of each LED, performance of each LED due to production uniformity, and pointing of LED module. Effects of these factors are considered to study the uniformity of LED Light Illumination. Numerical analysis is performed by assuming a serious of control factors to have a better understanding of each factor.

Design of High Efficiency Illumination for LED Lighting

Directory of Open Access Journals (Sweden)

Yong-Nong Chang

2013-01-01

Full Text Available A high efficiency illumination for LED street lighting is proposed. For energy saving, this paper uses Class-E resonant inverter as main electric circuit to improve efficiency. In addition, single dimming control has the best efficiency, simplest control scheme and lowest circuit cost among other types of dimming techniques. Multiple serial-connected transformers used to drive the LED strings as they can provide galvanic isolation and have the advantage of good current distribution against device difference. Finally, a prototype circuit for driving 112 W LEDs in total was built and tested to verify the theoretical analysis.

Slim planar apparatus for converting LED light into collimated polarized light uniformly emitted from its top surface.

Science.gov (United States)

Teng, Tun-Chien; Tseng, Li-Wei

2014-10-20

This study proposes a slim planar apparatus for converting nonpolarized light from a light-emitting diode (LED) into an ultra-collimated linearly polarized beam uniformly emitted from its top surface. The apparatus was designed based on a folded-bilayer configuration comprising a light-mixing collimation element, polarization conversion element, and polarization-preserving light guide plate (PPLGP) with an overall thickness of 5 mm. Moreover, the apparatus can be extended transversally by connecting multiple light-mixing collimation elements and polarization conversion elements in a side-by-side configuration to share a considerably wider PPLGP, so the apparatus can have theoretically unlimited width. The simulation results indicate that the proposed apparatus is feasible for the maximal backlight modules in 39-inch liquid crystal panels. In the case of an apparatus with a 480 × 80 mm emission area and two 8-lumen LED light sources, the average head-on polarized luminance and spatial uniformity over the emission area was 5000 nit and 83%, respectively; the vertical and transverse angular distributions of the emitting light were only 5° and 10°, respectively. Moreover, the average degree of polarization and energy efficiency of the apparatus were 82% and 72%, respectively. As compared with the high-performance ultra-collimated nonpolarized backlight module proposed in our prior work, not only did the apparatus exhibit outstanding optical performance, but also the highly polarized light emissions actually increased the energy efficiency by 100%.

Smart street lighting : The advantages of LED street lighting and a smart control system in Uppsala municipality

OpenAIRE

Sjöberg, Inga; Gidén Hember, Amanda; Wallerström, Carolina

2017-01-01

The purpose of this bachelor thesis is to examine how LED street lights and a smart street light control system can reduce the energy consumption, costs and in extension the CO2 equivalents in a geographically delimited area. In 2015 the municipality of Sala installed LED armatures connected to a smart control system in the whole municipality. The smart control system enables for instance adjustment of the light intensity at specific times during the day and a supervision of the street light ...

The Use of Light-Emitting Diodes (LEDs) as Green and Red/Far-Red Light Sources in Plant Physiology.

Science.gov (United States)

Jackson, David L.; And Others

1985-01-01

The use of green, red, and far-red light-emitting diodes (LEDs) as light sources for plant physiological studies is outlined and evaluated. Indicates that LED lamps have the advantage over conventional light sources in that they are lightweight, low-cost, portable, easily constructed, and do not require color filters. (Author/DH)

User evaluation of eight led light sources with different special colour rendering indices R9

DEFF Research Database (Denmark)

Markvart, Jakob; Iversen, Anne; Logadottir, Asta

2013-01-01

In this study we evaluated the influence of the special colour rendering index R9 on subjective red colour perception and Caucasian skin appearance among untrained test subjects. The light sources tested are commercially available LED based light sources with similar correlated colour temperature...

Design of High Efficiency Illumination for LED Lighting

OpenAIRE

Chang, Yong-Nong; Cheng, Hung-Liang; Kuo, Chih-Ming

2013-01-01

A high efficiency illumination for LED street lighting is proposed. For energy saving, this paper uses Class-E resonant inverter as main electric circuit to improve efficiency. In addition, single dimming control has the best efficiency, simplest control scheme and lowest circuit cost among other types of dimming techniques. Multiple serial-connected transformers used to drive the LED strings as they can provide galvanic isolation and have the advantage of good current distribution against de...

Large area flexible lighting foils using distributed bare LED dies on polyester substrates

NARCIS (Netherlands)

Ende, D.A. van den; Kusters, R.H.L.; Cauwe, M.; Waal, A. van der; Brand, J. van den

2013-01-01

Integration of LEDs on flexible foil substrates is of interest for flexible lighting applications and for backlights for flexible displays. Such a large area lighting device can be made by integrating a matrix of closely spaced LEDs on a flexible foil substrate. Preferably, these LEDs are integrated

Demonstration Assessment of Light-Emitting Diode (LED) Post-Top Lighting at Central Park in New York City

Energy Technology Data Exchange (ETDEWEB)

Myer, Michael; Goettel, Russell T.; Kinzey, Bruce R.

2012-09-30

A review of five post-top light-emitting diode (LED) pedestrian luminaires installed in New York City's Central Park for possible replacement to the existing metal halide post-top luminaire. This report reviews the energy savings potential and lighting delivered by the LED post-top luminaires.

Artificial LED lighting enhances growth characteristics and total phenolic content of Ocimum basilicum, but variably affects transplant success

NARCIS (Netherlands)

Bantis, Filippos; Ouzounis, Theoharis; Radoglou, Kalliopi

2016-01-01

The morphological and phytochemical characteristics of two Ocimum basilicum cultivars (Lettuce Leaf, and Red Rubin-mountain Athos hybrid) under artificial lighting were investigated. Four LED light treatments [AP673L (high red and high red:far-red), G2 (high red and low red:far-red), AP67

OSL response bleaching of BeO samples, using fluorescent light and blue LEDs

International Nuclear Information System (INIS)

Groppo, Daniela Piai; Caldas, Linda V.E.

2015-01-01

The optically stimulated luminescence (OSL) is widely used as a dosimetric technique for many applications. In this work, the OSL response bleaching of BeO samples was studied. The samples were irradiated using a beta radiation source ( 90 Sr+ 90 Y); the bleaching treatments (fluorescent light and blue LEDs) were performed, and the results were compared. Various optical treatment time intervals were tested until reaching the complete bleaching of the OSL response. The best combination of the time interval and bleaching type was analyzed. (author)

OSL response bleaching of BeO samples, using fluorescent light and blue LEDs

International Nuclear Information System (INIS)

Groppo, D P; Caldas, L V E

2016-01-01

The optically stimulated luminescence (OSL) is widely used as a dosimetric technique for many applications. In this work, the OSL response bleaching of BeO samples was studied. The samples were irradiated using a beta radiation source ("9"0Sr+"9"0Y); the bleaching treatments (fluorescent light and blue LEDs) were performed, and the results were compared. Various optical treatment time intervals were tested until reaching the complete bleaching of the OSL response. The best combination of the time interval and bleaching type was analyzed. (paper)

Study of LED layout in indoor visible light communication and performance analysis

Science.gov (United States)

Wang, Jiaan; Che, Ying; Wang, Xinlan; Guo, Linyang; Li, Jing

2017-10-01

Light emitting diodes(LED) could provide both illumination and data communication in indoor visible light communication(VLC) that owns the modulation bandwith from several from several MHz to seneral hundreds of MHz. The layout of LED plays an important role in maintaining a steady optical power distribution over the receiving plane. The existing rectangular LED layout does not provide a full coverage on the receiving plane leaving receiving optical power outage area, which in turn affects the best performance of the VLC system. This paper design a circular layout scheme of LED in 5mX5mX3m room based on the criterion of the illumination minimum mean square deviation. The influence of the distribution of the intensity of illumination with the radius of 1m and 1.5m,for including the wall reflection and not including the wall reflection, and make a comparison with rectangular LED layout of illumination distribution, when the number of LEDs with rectangular layout as same as circular layout. Including the number of LEDs are 4 and 16.For a specific simulation parameters as following:height of receiving plane is 0.85m,a single LEDs is composed of 60X60 LED chips, the parameters of a single chip is that transmitting power is 20mW,center luminous intensity is 0.73cd.semiangle at half power is 70deg.The parameters of concentrator is that photodiode area is 1cm2,photodiode responsivity is 0.4,field of view at the receiver is 85deg.Other parameters are that reflective index of concentrator is 1.5,reflectivity of wall is 0.8.Circular layout and rectangular layout are analyzed through simulation of the received optical power distribution, signal noise ratio distribution in non line of sight(including the wall reflection) and line of sight(not including the wall reflection),when the number of the LED is different. It is clear from the results that the received optical power distribution of non line of sight is better than line of sight, when the number of the LED are same, but

Comparative Phenotypical and Molecular Analyses of Arabidopsis Grown under Fluorescent and LED Light

Directory of Open Access Journals (Sweden)

Franka Seiler

2017-06-01

Full Text Available Comparative analyses of phenotypic and molecular traits of Arabidopsis thaliana grown under standardised conditions is still a challenge using climatic devices supplied with common light sources. These are in most cases fluorescent lights, which have several disadvantages such as heat production at higher light intensities, an invariable spectral output, and relatively rapid “ageing”. This results in non-desired variations of growth conditions and lowers the comparability of data acquired over extended time periods. In this study, we investigated the growth behaviour of Arabidopsis Col0 under different light conditions, applying fluorescent compared to LED lamps, and we conducted physiological as well as gene expression analyses. By changing the spectral composition and/or light intensity of LEDs we can clearly influence the growth behaviour of Arabidopsis and thereby study phenotypic attributes under very specific light conditions that are stable and reproducible, which is not necessarily given for fluorescent lamps. By using LED lights, we can also roughly mimic the sun light emission spectrum, enabling us to study plant growth in a more natural-like light set-up. We observed distinct growth behaviour under the different light regimes which was reflected by physiological properties of the plants. In conclusion, LEDs provide variable emission spectra for studying plant growth under defined, stable light conditions.

Direct battery-driven solar LED lighting using constant-power control

KAUST Repository

Huang, Bin-Juine; Chen, Chun-Wei; Hsu, Po-Chien; Tseng, Wei-Min; Wu, Min-Sheng

2012-01-01

A direct battery-driven LED lighting technique using constant-power control is proposed in the present study. A system dynamics model of LED luminaire was derived and used in the design of the feedback constant-power control system. The test result

Effectiveness of composite resin polymerization using light-emitting diodes (LEDs or halogen-based light-curing units Efetividade de polimerização de uma resina composta fotopolimerizada por diodos emissores de luz (LEDs ou luz halógena

Directory of Open Access Journals (Sweden)

Bianca Micali

2004-09-01

Full Text Available The clinical performance of composite resins is greatly influenced by the quality of the light-curing unit used. The aim of this study was to compare the efficiency of a commercial light-emitting diode (LED with that of a halogen-based light-curing unit by means of dye penetration of a micro hybrid composite resin. The composite resin evaluated was Filtek Z250 (3M Dental. The composite was filled into acrylic moulds that were randomly polymerized for 40 seconds by each of the light-emitting systems: light-emitting diode Ultraled (Dabi Atlante or halogen light Degulux (Degussa Hüls curing units. Immediately after polymerization, each specimen was individually immersed in 1 ml of 2% methylene blue solution at 37°C ± 2°C. After 24 hours, the specimens were rinsed under running distilled water for 1 minute and stored at 37°C ± 2°C at relative humidity for 24 hours. The composite resins were removed from the moulds and individually triturated before being immersed in new test tubes containing 1 ml of absolute alcohol for 24 hours. The solutions were filtered and centrifuged for 3 minutes at 4,000 rpm and the supernatant was used to determine absorbance in a spectrophotometer at 590 nm. To verify the differences between groups polymerized by LED or halogen light t-test was applied. No significant differences were found between composite resins light-cured by LED or halogen light-curing unit (p > 0.05. The commercially LED-based light-curing unit is as effective to polymerize hybrid composite resins as the halogen-based unit.A longevidade clínica das resinas compostas é grandemente influenciada pela qualidade do aparelho fotopolimerizador utilizado. O objetivo deste trabalho foi comparar a eficácia de um aparelho fotopolimerizador de diodos emissores de luz e a de um de luz halógena através do grau de penetração de um corante em uma resina composta micro-híbrida. A resina composta utilizada (Filtek Z250/3M Dental foi inserida em matrizes

Is a {mu}mol a {mu}mol? Growth and development of chrysanthemum cultivated under SON-T lighting and under LED-lighting; Is a {mu}mol a {mu}mol? Groei en ontwikkeling van chrysant geteeld onder SON-T belichting en onder LED verlichting

Energy Technology Data Exchange (ETDEWEB)

Meinen, E.; Marcelis, L.F.M.; Steenhuizen, J.W.; Dueck, T.A.

2009-12-15

Description of an experiment that was conducted, comparing LED lamps and SON-T (high pressure sodium) lamps. In climate rooms with LED (96% red sodium lamps) or SON-T lamps (without daylight), chrysanthemums were cultivated at two light intensities. Although the air temperature was the same in both treatments, the leaf temperature was clearly higher in the case of SON-T as a result of heat radiation. In the case of LED a more round leaves were observed. Plants cultivated under SON-T light developed closed crops much quicker and required a shorter reaction time (10 to 14 days at high and low light intensity). Yet, the harvest weight of the branches was the same. The net leaf photosynthesis was lower in chrysanthemums cultivated under LED lighting compared to plants cultivated under SON-T lighting. This is probably due to long-term cultivation under a spectrum of almost exclusively red light. The differences between SON-T and LED with regard to light color and heat radiation have significant consequences for growth and development. [Dutch] Een experiment is uitgevoerd om LED lampen en SON-T (hogedruk natriumlampen) lampen te vergelijken. In klimaatkamers met LED (96% rood en 4% blauw) of SON-T lampen (zonder daglichttoetreding) werden chrysanten geteeld bij 2 lichtintensiteiten. Hoewel de luchttemperatuur identiek was bij beide behandelingen was de bladtemperatuur duidelijk hoger bij SON-T als gevolg van warmtestraling. Onder LED belichting werd meer 'bol blad' waargenomen. Planten geteeld onder SON-T belichting ontwikkelden sneller een gesloten gewas en hadden een kortere reactietijd (10 tot 14 dagen bij hoge en lage lichtintensiteit). Maar het oogstgewicht van de takken was gelijk. De netto actuele bladfotosynthese was lager bij chrysanten geteeld onder LED belichting vergeleken met planten geteeld onder SON-T belichting. Dit is waarschijnlijk toe te schrijven aan langdurige teelt onder een spectrum met vrijwel alleen rood licht. De verschillen tussen SON

Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting, I-35W Bridge, Minneapolis, Minnesota, Phase I Report

Energy Technology Data Exchange (ETDEWEB)

Kinzey, B. R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Myer, M. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2009-08-01

On the I-35W Bridge in Minneapolis, Minnesota, the GATEWAY program conducted a two-phase demonstration of LED roadway lighting on the main span, which is one of the country's oldest continuously operated exterior LED lighting installations. The Phase I report provides an overview of initial project results including lighting performance, economic performance, and potential energy savings.

Illuminating the Pecking Order in Off-Grid Lighting: A Demonstration of LED Lighting for Saving Energy in the Poultry Sector

Energy Technology Data Exchange (ETDEWEB)

Tracy, Jennifer; Mills, Evan

2010-11-06

The Lumina Project and Lighting Africa conducted a full-scale field test involving a switch from kerosene to solar-LED lighting for commercial broiler chicken production at an off-grid farm in Kenya. The test achieved lower operating costs, produced substantially more light, improved the working environment, and had no adverse effect on yields. A strategy using conventional solar-fluorescent lighting also achieved comparable yields, but entailed a six-fold higher capital cost and significantly higher recurring battery replacement costs. Thanks to higher energy and optical efficiencies, the LED system provided approximately twice the illumination to the chicken-production area and yet drew less than half the power.At the study farm, 3000 chickens were grown in each of three identical houses under kerosene, fluorescent, and LED lighting configurations. Under baseline conditions, a yearly expenditure of 1,200 USD is required to illuminate the three houses with kerosene. The LED system eliminates this fuel use and expense with a corresponding simple payback time of 1.5 years, while the solar-fluorescent system has a payback time of 9.3 years. The corresponding reduction in fuel expenditure in both cases represents a 15percent increase in after-tax net income (revenues minus expenses) across the entire business operation. The differential cost-effectiveness between the LED and fluorescent systems would be substantially greater if the fluorescent system were upsized to provide the same light as the LED system. Providing light with the fluorescent or LED systems is also far more economical than connecting to the grid in this case. The estimated grid-connection cost at this facility is 1.7 million Kenya Schillings (approximately 21,250 USD), which is nearly six-times the cost of the fluorescent system and 35-times the cost of the LED system.The LED system also confers various non-energy benefits. The relative uniformity of LED lighting, compared to the fluorescent or

Communications and sensing of illumination contributins in a power LED lighting system

NARCIS (Netherlands)

Linnartz, J.P.M.G.; Feri, L.; Yang, Hongming; Colak, S.B.; Schenk, T.C.W.

2008-01-01

In recent years, LED technology emerged as a prime candidate for the future illumination light source, due to high energy efficiency and long life time. In addition, LEDs offer a superior flexibility in terms of colors and shapes, which leads to a potentially infinite variety of available light

Combined daylight and intelligent LED lighting - getting the daylight into the buildings; Kombineret dagslys og intelligent LED belysning - fae dagslys ind i bygningerne. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

Dam-Hansen, C.; Corell, D.D.; Thorseth, A.; Behrensdorff Poulsen, P. [Technical Univ. of Denmark, DTU Fotonik, DTU Risoe Campus, Roskilde (Denmark); Markvart, J.; Iversen, A.; Logadottir, A. [Aalborg Univ., Statens Byggeforskningsinstitut (SBi), Koebenhavn (Denmark)

2013-03-15

The main result of the project is the construction of the new intelligent and dynamic LED lighting system for demonstration and research purposes, and a number of extensive user testing is completed. The LED lighting system is a total system for office lighting with ceiling fixtures and desk lamps, which has made it possible to create a general and workplace lighting in two offices each with two work places. The system is installed in a day light laboratory for such two office spaces. All lamps can be controlled via a developed computer interface, and the desk lamps are further manually controllable by a user via two buttons for color temperature and brightness, respectively. The new intelligent and dynamic lighting system is based on color mixing LED technology and makes it possible to control the color composition, color coordinates and thus the color temperature of the light. Control-wise, the system is pre-programmed to produce white light with a correlated color temperature from 2700 K to 7000 K. The color composition is optimized from the desire for a very good color given at a general CRI value of 92-97 over the area. The system can be dimmed 20-100 %, with no significant change in the light's color properties. A mini-spectrometer is calibrated and built-in in the system and provides the current estimate of daylight brightness and color temperature through measurement of daylight color scheme in the visible range. The system uses daylight properties to control the light from the LED lighting system. The results of user tests show, that the developed possibility to automatically control of light in the office depending on the daylight color temperature is considered to be equally preferred and results in equally satisfied users as a traditional lighting system with even lighting in the room. On the other hand, user results showed that there were both energy savings and more satisfied users to be gained by providing users the opportunity to self-adjust either

Technology Analysis of Global Smart Light Emitting Diode (LED Development Using Patent Data

Directory of Open Access Journals (Sweden)

Sangsung Park

2017-08-01

Full Text Available Technological developments related to smart light emitting diode (LED systems have progressed rapidly in recent years. In this paper, patent documents related to smart LED technology are collected and analyzed to understand the technology development of smart LED systems. Most previous studies of the technology were dependent on the knowledge and experience of domain experts, using techniques such as Delphi surveys or technology road-mapping. These approaches may be subjective and lack robustness, because the results can vary according to the selected expert groups. We therefore propose a new technology analysis methodology based on statistical modeling to obtain objective and relatively stable results. The proposed method consists of visualization based on Bayesian networks and a linear count model to analyze patent documents related to smart LED technology. Combining these results, a global hierarchical technology structure is created that can enhance the sustainability in smart LED system technology. In order to show how this methodology could be applied to real-world problems, we carry out a case study on the technology analysis of smart LED systems.

Efficient and versatile light. LEDs save energy and open up manifold possibilities of design; Effizientes und vielseitiges Licht. LEDs sparen Energie und eroeffnen zahlreiche Designmoeglichkeiten

Energy Technology Data Exchange (ETDEWEB)

Fiebig, Michael [OSRAM Opto Semicondutors GmbH, Muenchen (Germany). Bereich Marketing und Business Development

2010-07-01

Light bulbs leave the European market step by step. These conventional light sources are too inefficient in the private and conventional sector. There are a lot of alternatives to light bulbs. But no technology will be able to save as much energy as light emitting diodes (LED) in the future. Today, these LEDs meet us in most different applications. Continuously new areas of application are opened up in order to reduce the power requirement clearly for the production of artificial light. Apart from energy conservation diodes also enable untold possibilities. In the future, light can be still more flexibly used owing to LED. LEDs are ideal light sources for planners and designers.

Wireless high-speed data transmission with phosphorescent white-light LEDs

NARCIS (Netherlands)

Grubor, J.; Lee, S.C.J.; Langer, K-D.; Koonen, A.M.J.; Walewski, J.

2007-01-01

Wireless transmission exceeding 100 Mbit/s is demonstrated using a phosphorescent white-light LED in a lighting-like scenario. The data rate was achieved by detecting the blue part of the optical spectrum and applying discrete multi-tone modulation.

Development of a LED based standard for luminous flux

Science.gov (United States)

Sardinha, André; Ázara, Ivo; Torres, Miguel; Menegotto, Thiago; Grieneisen, Hans Peter; Borghi, Giovanna; Couceiro, Iakyra; Zim, Alexandre; Muller, Filipe

2018-03-01

Incandescent lamps, simple artifacts with radiation spectrum very similar to a black-body emitter, are traditional standards in photometry. Nowadays LEDs are broadly used in lighting, with great variety of spectra, and it is convenient to use standards for photometry with spectral distribution similar to that of the measured artifact. Research and development of such standards occur in several National Metrology Institutes. In Brazil, Inmetro is working on a practical solution for providing a LED based standard to be used for luminous flux measurements in the field of general lighting. This paper shows the measurements made for the developing of a prototype, that in sequence will be characterized in photometric quantities.

Investigation of structure in the modular light pipe component for LED automotive lamp

Science.gov (United States)

Chen, Hsi-Chao; Zhou, Yang; Huang, Chien-Sheng; Jhong, Wan-Ling; Cheng, Bo-Wei; Jhang, Jhe-Ming

2014-09-01

Light-Emitting Diodes (LEDs) have the advantages of small length, long lifetime, fast response time (μs), low voltage, good mechanical properties and environmental protection. Furthermore, LEDs could replace the halogen lamps to avoid the mercury pollution and economize the use of energy. Therefore, the LEDs could instead of the traditional lamp in the future and became an important light source. The proposal of this study was to investigate the effects of the structure and length of the reflector component for a LED automotive lamp. The novel LED automotive lamp was assembled by several different modularization columnar. The optimized design of the different structure and the length to the reflector was simulated by software TracePro. The design result must met the vehicle regulation of United Nations Economic Commission for Europe (UNECE) such as ECE-R19 etc. The structure of the light pipe could be designed by two steps structure. Then constitute the proper structure and choose different power LED to meet the luminous intensity of the vehicle regulation. The simulation result shows the proper structure and length has the best total luminous flux and a high luminous efficiency for the system. Also, the stray light could meet the vehicle regulation of ECE R19. Finally, the experimental result of the selected structure and length of the light pipe could match the simulation result above 80%.

A white–cyan-red LED system for low correlated colour temperature lighting

DEFF Research Database (Denmark)

Chakrabarti, Maumita; Thorseth, Anders; Corell, Dennis Dan

2015-01-01

A white LED complemented by cyan and red LEDs is a good candidate for achieving high colour rendering at low correlated colour temperatures. This is usually very difficult with commercially available white LEDs. In addition, the system is able to replace incandescent lighting in many applications...... to 2400 K. Within this range the white light is characterized by a high general colour rendering index (Ra>90), special colour rendering indices for saturated red objects (R9>85), and low chromaticity distance (Duv) from the Planckian locus (Duv

LED and Halogen Light Transmission through a CAD/CAM Lithium Disilicate Glass-Ceramic.

Science.gov (United States)

Pereira, Carolina Nemesio de Barros; De Magalhães, Cláudia Silami; Daleprane, Bruno; Peixoto, Rogéli Tibúrcio Ribeiro da Cunha; Ferreira, Raquel da Conceição; Cury, Luiz Alberto; Moreira, Allyson Nogueira

2015-01-01

The effect of thickness, shade and translucency of CAD/CAM lithium disilicate glass-ceramic on light transmission of light-emitting diode (LED) and quartz-tungsten-halogen units (QTH) were evaluated. Ceramic IPS e.max CAD shades A1, A2, A3, A3.5, high (HT) and low (LT) translucency were cut (1, 2, 3, 4 and 5 mm). Light sources emission spectra were determined. Light intensity incident and transmitted through each ceramic sample was measured to determine light transmission percentage (TP). Statistical analysis used a linear regression model. There was significant interaction between light source and ceramic translucency (p=0.008) and strong negative correlation (R=-0.845, pceramic thickness and TP. Increasing one unit in thickness led to 3.17 reduction in TP. There was no significant difference in TP (p=0.124) between shades A1 (ß1=0) and A2 (ß1=-0.45) but significant reduction occurred for A3 (ß1=-0.83) and A3.5 (ß1=-2.18). The interaction QTH/HT provided higher TP (ß1=0) than LED/HT (ß1=-2.92), QTH/LT (ß1=-3.75) and LED/LT (ß1=-5.58). Light transmission was more effective using halogen source and high-translucency ceramics, decreased as the ceramic thickness increased and was higher for the lighter shades, A1 and A2. From the regression model (R2=0.85), an equation was obtained to estimate TP value using each variable ß1 found. A maximum TP of 25% for QTH and 20% for LED was found, suggesting that ceramic light attenuation could compromise light cured and dual cure resin cements polymerization.

Bivariate constant stress degradation model: LED lighting system reliability estimation with two-stage modelling

NARCIS (Netherlands)

Sari, J.K.; Newby, M.J.; Brombacher, A.C.; Tang, L.C.

2009-01-01

Light-emitting diode (LED) lamp has received great attention as a potential replacement for the more commercially available lighting technology, such as incandescence and fluorescence lamps. LED which is the main component of LED lamp has a very long lifetime. This means that no or very few failures

Forward Conduction Mode Controlled Piezoelectric Transformer-Based PFC LED Drive

DEFF Research Database (Denmark)

Roedgaard, M. S.; Weirich, M.; Andersen, M. A. E.

2013-01-01

Light-emitting diode (LED) illumination is getting more and more common; as LED's performance is rising, the price is falling and is getting competitive. Some of the challenges of ac mains supplied illumination are the requirement of power factor correction (PFC) and the competitiveness of a low...... priced market. In this paper, a new forward conduction mode (FCM) control method for piezoelectric transformer (PT)-based power converters is proposed. A PT-based LED drive facilitating passive PFC is developed, utilizing and validating the FCM control method. The drive utilizes an inductorless half...... LED drive has been developed, supplied from 230-V 50-Hz ac mains, achieving a power factor of 0.96....

Color design model of high color rendering index white-light LED module.

Science.gov (United States)

Ying, Shang-Ping; Fu, Han-Kuei; Hsieh, Hsin-Hsin; Hsieh, Kun-Yang

2017-05-10

The traditional white-light light-emitting diode (LED) is packaged with a single chip and a single phosphor but has a poor color rendering index (CRI). The next-generation package comprises two chips and a single phosphor, has a high CRI, and retains high luminous efficacy. This study employs two chips and two phosphors to improve the diode's color tunability with various proportions of two phosphors and various densities of phosphor in the silicone used. A color design model is established for color fine-tuning of the white-light LED module. The maximum difference between the measured and color-design-model simulated CIE 1931 color coordinates is approximately 0.0063 around a correlated color temperature (CCT) of 2500 K. This study provides a rapid method to obtain the color fine-tuning of a white-light LED module with a high CRI and luminous efficacy.

Energy-Saving Tunnel Illumination System Based on LED's Intelligent Control

International Nuclear Information System (INIS)

Guo Shanshan; Wu Lan; Gu Hanting; Jiang Shuixiu

2011-01-01

At present there is a lot of electric energy wastage in tunnel illumination, whose design is based on the maximum brightness outside and the maximum vehicle speed all year round. LED's energy consumption is low, and the control of its brightness is simple and effective. It can be quickly adjusted between 0-100% of its maximum brightness, and will not affect the service life. Therefore, using LED as tunnel's illumination source, we can achieve a good energy saving effect. According to real-time data acquisition of vehicle speed, traffic flow and brightness outside the tunnel, the auto real-time control of tunnel illumination can be achieved. And the system regulated the LED luminance by means of combination of LED power module and intelligent control module. The tunnel information was detected by inspection equipments, which included luminometer, vehicle detector, and received by RTU(Remote Terminal Unit), then synchronously transmitted to PC. After data processing, RTU emitted the dimming signal to the LED driver to adjust the brightness of LED. Despite the relatively high cost of high-power LED lights, the enormous energy-saving effect and the well-behaved controllability is beyond compare to other lighting devices.

Evaluation of a LED-based flatbed document scanner for radiochromic film dosimetry in transmission mode.

Science.gov (United States)

Lárraga-Gutiérrez, José Manuel; García-Garduño, Olivia Amanda; Treviño-Palacios, Carlos; Herrera-González, José Alfredo

2018-03-01

Flatbed scanners are the most frequently used reading instrument for radiochromic film dosimetry because its low cost, high spatial resolution, among other advantages. These scanners use a fluorescent lamp and a CCD array as light source and detector, respectively. Recently, manufacturers of flatbed scanners replaced the fluorescent lamp by light emission diodes (LED) as a light source. The goal of this work is to evaluate the performance of a commercial flatbed scanner with LED based source light for radiochromic film dosimetry. Film read out consistency, response uniformity, film-scanner sensitivity, long term stability and total dose uncertainty was evaluated. In overall, the performance of the LED flatbed scanner is comparable to that of a cold cathode fluorescent lamp (CCFL). There are important spectral differences between LED and CCFL lamps that results in a higher sensitivity of the LED scanner in the green channel. Total dose uncertainty, film response reproducibility and long-term stability of LED scanner are slightly better than those of the CCFL. However, the LED based scanner has a strong non-uniform response, up to 9%, that must be adequately corrected for radiotherapy dosimetry QA. The differences in light emission spectra between LED and CCFL lamps and its potential impact on film-scanner sensitivity suggest that the design of a dedicated flat-bed scanner with LEDs may improve sensitivity and dose uncertainty in radiochromic film dosimetry. Copyright © 2018 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Bridging “green gap” of LEDs: Giant light output enhancement and directional control of LEDs via embedded nano-void photonic crystals

KAUST Repository

Tsai, Yu-Lin

2015-11-23

Green LEDs do not show the same level of performance as their blue and red cousins, greatly hindering the solid-state lighting development, which is so-called “green gap”. In this work, nano-void photonic crystals (NVPCs) were fabricated to embed within the GaN/InGaN green LEDs by using epitaxial lateral overgrowth (ELO) and nano-sphere lithography techniques. The NVPCs act as an efficient scattering back-reflector to outcouple the guided and downward photons, which not only boosting light extraction efficiency of LEDs with an enhancement of 78% but also collimating the view angle of LEDs from 131.5゜to 114.0゜. This could be because the highly scattering nature of NVPCs which reduce the interference giving rise to Fabry-Perot resonance. Moreover, due to the threading dislocation suppression and strain relief by the NVPCs, the internal quantum efficiency was increased by 25% and droop behavior was reduced from 37.4% to 25.9%. The enhancement of light output power can be achieved as high as 151% at a driving current of 350 mA. Giant light output enhancement and directional control via NVPCs points the way towards a promising avenue of solid-state lighting.

Bridging “green gap” of LEDs: Giant light output enhancement and directional control of LEDs via embedded nano-void photonic crystals

KAUST Repository

Tsai, Yu-Lin; Liu, Che-Yu; Krishnan, Chirenjeevi; Lin, Da-Wei; Chu, You-Chen; Chen, Tzu-Pei; Shen, Tien-Lin; Kao, Tsung-Sheng; Charlton, Martin; Yu, Peichen; Lin, Chien-Chung; Kuo, Hao-Chung; He, Jr-Hau

2015-01-01

Green LEDs do not show the same level of performance as their blue and red cousins, greatly hindering the solid-state lighting development, which is so-called “green gap”. In this work, nano-void photonic crystals (NVPCs) were fabricated to embed within the GaN/InGaN green LEDs by using epitaxial lateral overgrowth (ELO) and nano-sphere lithography techniques. The NVPCs act as an efficient scattering back-reflector to outcouple the guided and downward photons, which not only boosting light extraction efficiency of LEDs with an enhancement of 78% but also collimating the view angle of LEDs from 131.5゜to 114.0゜. This could be because the highly scattering nature of NVPCs which reduce the interference giving rise to Fabry-Perot resonance. Moreover, due to the threading dislocation suppression and strain relief by the NVPCs, the internal quantum efficiency was increased by 25% and droop behavior was reduced from 37.4% to 25.9%. The enhancement of light output power can be achieved as high as 151% at a driving current of 350 mA. Giant light output enhancement and directional control via NVPCs points the way towards a promising avenue of solid-state lighting.

Meeting the challenges of developing LED-based projection displays

Science.gov (United States)

Geißler, Enrico

2006-04-01

The main challenge in developing a LED-based projection system is to meet the brightness requirements of the market. Therefore a balanced combination of optical, electrical and thermal parameters must be reached to achieve these performance and cost targets. This paper describes the system design methodology for a digital micromirror display (DMD) based optical engine using LEDs as the light source, starting at the basic physical and geometrical parameters of the DMD and other optical elements through characterization of the LEDs to optimizing the system performance by determining optimal driving conditions. LEDs have a luminous flux density which is just at the threshold of acceptance in projection systems and thus only a fully optimized optical system with a matched set of LEDs can be used. This work resulted in two projection engines, one for a compact pocket projector and the other for a rear projection television, both of which are currently in commercialization.

Assessing the use of Low Voltage UV-light Emitting Miniature LEDs for Marine Biofouling Control

Science.gov (United States)

2016-07-01

of that required to drive traditional UV mercury lamps . Secondly, given their small size and relatively low cost, UV LEDs provide ease of maintenance...UNCLASSIFIED UNCLASSIFIED Assessing the use of Low Voltage UV -light Emitting Miniature LEDs for Marine Biofouling Control Richard...settling organisms. The introduction of miniature UV light emitting diodes ( LEDs ) as a light source enables them to be embedded into thin, flexible

A 2 x 2 imaging MIMO system based on LED Visible Light Communications employing space balanced coding and integrated PIN array reception

DEFF Research Database (Denmark)

Li, Jiehui; Xu, Yinfan; Shi, Jianyang

2016-01-01

In this paper, we proposed a 2 x 2 imaging Multi-Input Multi-Output (MIMO)-Visible Light Communication (VLC) system by employing Space Balanced Coding (SBC) based on two RGB LEDs and integrated PIN array reception. We experimentally demonstrated 1.4-Gbit/s VLC transmission at a distance of 2.5 m...

LED surgical lighting system with multiple free-form surfaces for highly sterile operating theater application.

Science.gov (United States)

Liu, Peng; Zhang, Yaqin; Zheng, Zhenrong; Li, Haifeng; Liu, Xu

2014-06-01

Although the ventilation system is widely employed in the operating theater, a strictly sterile surgical environment still cannot be ensured because of laminar disturbance, which is mainly caused by the surgical lighting system. Abandoning traditional products, we propose an LED surgical lighting system, which can alleviate the laminar disturbance and provide an appropriate lighting condition for surgery. It contains a certain amount of LED lens units, which are embedded in the ceiling and arranged around the air supply smallpox. The LED lens unit integrated with an LED light source and a free-form lens is required to produce a uniform circular illumination with a large tolerance to the change of lighting distance. To achieve such a dedicated lens, two free-form refractive surfaces, which are converted into two ordinary differential equations by the design method presented in this paper, are used to deflect the rays. The results show that the LED surgical lighting system can provide an excellent illumination environment for surgery, and, apparently, the laminar disturbance also can be relieved.

Assessment of filament led bulbs with respect to temporal light artefacts

DEFF Research Database (Denmark)

Lindén, Johannes; Thorseth, Anders; Corell, Dennis Dan

2017-01-01

Temporal light artefacts, abbreviated TLAs (including flicker, stroboscopic effect and phantom arrays), i.e. undesired time modulation in luminance from a light source, has shown to be a threat to wider SSL adoption especially related to dimming functions and low-quality LED products. This is due...... to the effects that both noticeable and unperceivable TLAs have on human perception and wellbeing. In the present work a number of filament LED bulbs, currently available on the market, are assessed primarily with respect to TLAs, but also with respect to photometric, colorimetric and efficiency properties...

Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting on Lija Loop in Portland, OR

International Nuclear Information System (INIS)

Kinzey, Bruce R.; Myer, Michael

2009-01-01

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a residential street lighting application, under the U.S. Department of Energy GATEWAY Solid-State Lighting Technology Demonstration Program. In this project, eight 100W (nominal) high-pressure sodium cobra head fixtures were replaced with a like number of LED street light luminaires manufactured by Leotek, Inc. The Leotek product achieved an estimated payback in the Lija Loop installation of about 20 years for replacement scenarios and a much shorter 7.6 years for new installations. Much of the associated energy savings (55%) supporting these payback periods, however, were achieved by reducing average horizontal photopic illuminance a similar amount (53%). Examined from a different perspective, the measured performance suggests that the Leotek product is at approximate parity with the HPS cobra head in terms of average delivered photopic illumination for a given power consumption. HPS comprises the second most efficacious street lighting technology available, exceeded only by low pressure sodium (LPS). LPS technology is not considered suitable for most street lighting applications due to its monochromatic spectral output and poor color rendering ability; therefore, this LED product is performing at an efficiency level comparable to its primary competition in this application.

Novel Coatings for Enhancement of Light-Emitting Diodes (LEDs)

Science.gov (United States)

2006-10-28

quantum efficiency of LEDs. SAIC’s strength is this area is a proprietary nonimaging optics code. In consultation with Lumileds, SAIC developed designs for...five different optical ele- ments that collect and project light from a LED. The simulations showed that the designs achieve a significant improvement... optical microscope at 100x power the coating is not visible. Fire sample 6DecO4P1 in tube furnace As a first test, sample 6Dec04P1 was progressively

A filter bank approach for LED illumintaion sensing based on frequency division multiplexing

NARCIS (Netherlands)

Yang, Hongming; Bergmans, J.W.M.; Schenk, T.C.W.

2009-01-01

In this work, we consider illumination sensing in a light emitting diode (LED) based illumination system that normally consists of a large number of LEDs. Illumination sensing is used in order to facilitate the control of such system whose complexity, due to the large number of LEDs, can be quite

Novel Transparent Phosphor Conversion Matrix with High Thermal Conductivity for Next Generation Phosphor-Converted LED-based Solid State Lighting

Energy Technology Data Exchange (ETDEWEB)

Bockstaller, Michael [Carnegie Mellon Univ., Pittsburgh, PA (United States)

2017-02-06

The low thermal conductivity of state-of-the-art polymer encapsulants (k ~ 0.15 Wm-1K-1) limits the efficiency and power density of current phosphor conversion light emitting diodes (pc-LEDs). The technical objective of this project was to demonstrate synthesis and processing schemes for the fabrication of polymer hybrid encapsulants with a thermal conductivity exceeding k = 0.4 Wm-1K-1 for LED applications. The ‘hybrid polymer’ approach encompasses the dispersion of high thermal conductivity particle fillers (zinc oxide, ZnO as well as the alpha-polymorph of alumina, Al2O3) within a polysiloxane matrix (poly(dimethylsiloxane), PDMS as well as poly(phenyl methyl siloxane), PPMS) to increase the thermal conductivity while maintaining optical transparency and photothermal stability at levels consistent with LED applications. To accomplish this goal, a novel synthesis method for the fabrication of nanosized ZnO particles was developed and a novel surface chemistry was established to modify the surface of zinc oxide particle fillers and thus to enable their dispersion in poly(dimethyl siloxane) (PDMS) matrix polymers. Molecular dynamics and Mie simulations were used to optimize ligand structure and to enable the concurrent mixing of particles in PDMS/PPMS embedding media while also minimizing the thermal boundary resistance as well as optical scattering of particle fillers. Using this approach the synthesis of PDMS/ZnO hybrid encapsulants exhibiting a thermal conductivity of 0.64 Wm-1K-1 and optical transparency > 0.7 mm-1 was demonstrated. A forming process based on micromolding was developed to demonstrate the forming of particle filled PDMS into film and lens shapes. Photothermal stability testing revealed stability of the materials for approximately 4000 min when exposed to blue light LED (450 nm, 30 W/cm2). One postgraduate and seven graduate students were supported by the project. The research performed within this project led to fifteen publications in peer

The nanorod approach: GaN NanoLEDs for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Waag, Andreas; Wang, Xue; Fuendling, Soenke; Ledig, Johannes; Erenburg, Milena; Neumann, Richard; Al Suleiman, Mohamed; Merzsch, Stephan; Wei, Jiandong; Li, Shunfeng; Wehmann, Hergo H. [Institut fuer Halbleitertechnik, TU Braunschweig, Hans-Sommer-Strasse 66, 38106 Braunschweig (Germany); Bergbauer, Werner; Strassburg, Martin [OSRAM Opto Semiconductors GmbH, Leibnizstr. 4, 93055 Regensburg (Germany); Trampert, Achim; Jahn, Uwe; Riechert, Henning [Paul-Drude-Institut fuer Festkoerperelektronik, Hausvogteiplatz 5-7, 10117 Berlin (Germany)

2011-07-15

Vertically aligned GaN nanorods have recently obtained substantial interest as a new approach to solid state lighting. In comparison to conventional planar LEDs, 3D NanoLEDs are expected to offer substantial advantageous: very low defect density, quasi free-standing, no strain due to mismatch of thermal expansion coefficients, no substrate bending even when grown on large area silicon. Core-shell strategies are another very interesting aspect. The active LED surface per wafer could be increased by more than one order of magnitude. However, most of these advantages have not yet been proven in real devices, which would include a quantitative comparison of light emission. Related to the 3D character, there are also technological risks. In the following we will discuss the main developments which have paved the way up to this point, including a detailed discussion of possible benefits and risks connected with the NanoLED approach (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Quality attributes of LED lighting. Current state-of-the-art , advantages, problem areas and potential for development - Final report; Qualitaetsmerkmale der LED-Beleuchtung. Aktueller Stand der Technik, Vorteile, Problempunkte und Entwicklungspotential - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Gasser, S.

2009-09-15

The present report describes the state-of-the-art of LED technology for room lighting in June 2009, based on internet research, expert interviews as well as a workshop with experts. Of the 20 attributes determined, three key quality characteristics crucial for the breakthrough of LED technology were identified: (i) Energy efficiency: with values of 50 - 70 lumen/watt when in usage, current LED lamps on the market are comparable to energy saving lamps. Experts expect the luminous efficiency to double within the next five years. Declaration is often poor: instead of efficiency in real-life usage many producers declare unrealistic lab measurement results; sometimes even fantasy values are declared. (ii) Light quality: Today's good LEDs reach colour rendering attributes which are comparable to those of halogen lamps and usually better than the CFL's (colour rendering index 80 to 90, with a continuous light spectrum). (iii) Lamp life: A lamp life of up to 50,000 hours can only be reached if the heat dissipation is secured and if the Control gears quality keeps up with the LED's life time. According to the experts, many of today's LED products on the market don't meet these two requirements. Strong uncertainty is caused by inconsistent declaration and partly missing standardisation. With the ANSI standard, the US is ahead of Europe in this matter. Today LED lighting is attractive and economic where its unique advantages can be applied: directional light, very long life-span, no heat in the luminous flux, UV-free light, colour modulation, dimming with little losses. Interesting applications today include: (i) Professional field: operating time > 3,000 hours per year, e.g. shop illumination or downlights in a hall (hotel, administration, etc.). Further spotlights in museums, working place table light fixtures, hybrid solutions (e.g. indirect fluorescent lamp, direct LED). (ii) Domestic field: working place and reading lamps (low luminance, no heat

Forward and correctional OFDM-based visible light positioning

Science.gov (United States)

Li, Wei; Huang, Zhitong; Zhao, Runmei; He, Peixuan; Ji, Yuefeng

2017-09-01

Visible light positioning (VLP) has attracted much attention in both academic and industrial areas due to the extensive deployment of light-emitting diodes (LEDs) as next-generation green lighting. Generally, the coverage of a single LED lamp is limited, so LED arrays are always utilized to achieve uniform illumination within the large-scale indoor environment. However, in such dense LED deployment scenario, the superposition of the light signals becomes an important challenge for accurate VLP. To solve this problem, we propose a forward and correctional orthogonal frequency division multiplexing (OFDM)-based VLP (FCO-VLP) scheme with low complexity in generating and processing of signals. In the first forward procedure of FCO-VLP, an initial position is obtained by the trilateration method based on OFDM-subcarriers. The positioning accuracy will be further improved in the second correctional procedure based on the database of reference points. As demonstrated in our experiments, our approach yields an improved average positioning error of 4.65 cm and an enhanced positioning accuracy by 24.2% compared with trilateration method.

The Design and Comparison of Central and Distributed Light Sensored Smart LED Lighting Systems

Directory of Open Access Journals (Sweden)

Mehmet Ali Özçelik

2018-01-01

Full Text Available There is a lack of published peer-reviewed research comparing the efficiencies of distributed versus central sensor-controlled LED lighting systems. This research proposes improving the smart illumination of a room with external fenestration using central and distributed light sensors. The optical and electrical measurements of the daylight have been made in the case where the light was not distributed evenly and not sufficient. Test results show that the proposed distributed light sensor illumination system has increased the efficiency by 28% when compared to the proposed central system. It has also been shown that the two tested systems are more cost-effective than common smart illumination systems.

III-nitride based light emitting diodes and applications

CERN Document Server

Han, Jung; Amano, Hiroshi; Morkoç, Hadis

2017-01-01

The revised edition of this important book presents updated and expanded coverage of light emitting diodes (LEDs) based on heteroepitaxial GaN on Si substrates, and includes new chapters on tunnel junction LEDs, green/yellow LEDs, and ultraviolet LEDs. Over the last two decades, significant progress has been made in the growth, doping and processing technologies of III-nitride based semiconductors, leading to considerable expectations for nitride semiconductors across a wide range of applications. LEDs are already used in traffic signals, signage lighting, and automotive applications, with the ultimate goal of the global replacement of traditional incandescent and fluorescent lamps, thus reducing energy consumption and cutting down on carbon-dioxide emission. However, some critical issues must be addressed to allow the further improvements required for the large-scale realization of solid-state lighting, and this book aims to provide the readers with details of some contemporary issues on which the performanc...

The Use of Ultra-Violet (UV) Light Emitting Diodes (LEDS) in an Advanced Oxidation Process (AOP) with Brilliant Blue FCF as an Indicator

Science.gov (United States)

2015-03-26

LEDs have the potential to replace mercury lamps in many UV processes, as well as open the door to new applications of UV light based on their unique...al. 2007, Autin, Romelot, et al. 2013). UV LEDs in AOPs While most data on AOP experimentation are based on experiments that use mercury lamps ...metaldehyde in solution. Their experiments found that similar UV light exposure levels from UV LEDs and traditional mercury lamps produced similar

A Simple, Small-Scale Lego Colorimeter with a Light-Emitting Diode (LED) Used as Detector

Science.gov (United States)

Asheim, Jonas; Kvittingen, Eivind V.; Kvittingen, Lise; Verley, Richard

2014-01-01

This article describes how to construct a simple, inexpensive, and robust colorimeter from a few Lego bricks, in which one light-emitting diode (LED) is used as a light source and a second LED as a light detector. The colorimeter is suited to various grades and curricula.

Technical Feasibility Assessment of LED Roadway Lighting on the Golden Gate Bridge

Energy Technology Data Exchange (ETDEWEB)

Tuenge, Jason R.

2012-09-01

Subsequent to preliminary investigations by the Golden Gate Bridge Highway & Transportation District (GGB), in coordination with Pacific Gas & Electric (PG&E), the GATEWAY Demonstration program was asked to evaluate the technical feasibility of replacing existing roadway lighting on the bridge with products utilizing LED technology. GGB and PG&E also indicated interest in induction (i.e., electrodeless fluorescent) technology, since both light source types feature rated lifetimes significantly exceeding those of the existing high-pressure sodium (HPS) and low-pressure sodium (LPS) products. The goal of the study was to identify any solutions which would reduce energy use and maintenance without compromising the quantity or quality of existing illumination. Products used for roadway lighting on the historic bridge must be installed within the existing amber-lensed shoebox-style luminaire housings. It was determined that induction technology does not appear to represent a viable alternative for the roadway luminaires in this application; any energy savings would be attributable to a reduction in light levels. Although no suitable LED retrofit kits were identified for installation within existing luminaire housings, several complete LED luminaires were found to offer energy savings of 6-18%, suggesting custom LED retrofit kits could be developed to match or exceed the performance of the existing shoeboxes. Luminaires utilizing ceramic metal halide (CMH) were also evaluated, and some were found to offer 28% energy savings, but these products might actually increase maintenance due to the shorter rated lamp life. Plasma technology was evaluated, as well, but no suitable products were identified. Analysis provided in this report was completed in May 2012. Although LED technologies are expected to become increasingly viable over time, and product mock-ups may reveal near-term solutions, some options not currently considered by GGB may ultimately merit evaluation. For

Monolithically Integrated Light Feedback Control Circuit for Blue/UV LED Smart Package

NARCIS (Netherlands)

Koladouz Esfahani, Z.; Tohidian, M.; van Zeijl, H.W.; Kolahdouz, Mohammadreza; Zhang, G.Q.

2017-01-01

Given the performance decay of high-power light-emitting diode (LED) chips over time and package condition changes, having a reliable output light for sensitive applications is a point of concern. In this study, a light feedback control circuit, including blue-selective photodiodes, for

USER EVALUATION OF EIGHT LED LIGHT SOURCES WITH DIFFERENTSPECIAL COLOUR RENDERING INDICES R9

DEFF Research Database (Denmark)

Markvart, Jakob; Iversen, Anne; Logadóttir, Ásta

2013-01-01

In this study we evaluated the influence of the special colour rendering index R9 on subjective red colour perception and Caucasian skin appearance among untrained test subjects. The light sources tested are commercially available LED based light sources with similar correlated colour temperature...... and general colour rendering index, but with varying R9. It was found that the test subjects in general are more positive towards light sources with higher R9. The shift from a majority of negative responses to a majority of positive responses is found to occur at R9 values of ~20....

[Hygienic aspects of the use of LED light sources for general illumination in schools].

Science.gov (United States)

Kuchma, V R; Sukhareva, L M; Teksheva, L M; Stepanova, M I; Sazaniuk, Z I

2013-01-01

For the time present becoming more common semiconductor sources of artificial lighting has become a more and more frequent practice. With the aim to study the impact of LEDs on the health of schoolchildren studies in experimental conditions (specially equipped classrooms) were performed. The comparative analysis of the state of vision, mental health and emotional state of pupils in primary, middle and high schools under fluorescent and LED lighting, meeting to the regulatory requirements, has revealed that the physiological cost of schooling in the use of LED units in classrooms is lower than in a traditional, fluorescent lighting.

An inexpensive Arduino-based LED stimulator system for vision research.

Science.gov (United States)

Teikari, Petteri; Najjar, Raymond P; Malkki, Hemi; Knoblauch, Kenneth; Dumortier, Dominique; Gronfier, Claude; Cooper, Howard M

2012-11-15

Light emitting diodes (LEDs) are being used increasingly as light sources in life sciences applications such as in vision research, fluorescence microscopy and in brain-computer interfacing. Here we present an inexpensive but effective visual stimulator based on light emitting diodes (LEDs) and open-source Arduino microcontroller prototyping platform. The main design goal of our system was to use off-the-shelf and open-source components as much as possible, and to reduce design complexity allowing use of the system to end-users without advanced electronics skills. The main core of the system is a USB-connected Arduino microcontroller platform designed initially with a specific emphasis on the ease-of-use creating interactive physical computing environments. The pulse-width modulation (PWM) signal of Arduino was used to drive LEDs allowing linear light intensity control. The visual stimulator was demonstrated in applications such as murine pupillometry, rodent models for cognitive research, and heterochromatic flicker photometry in human psychophysics. These examples illustrate some of the possible applications that can be easily implemented and that are advantageous for students, educational purposes and universities with limited resources. The LED stimulator system was developed as an open-source project. Software interface was developed using Python with simplified examples provided for Matlab and LabVIEW. Source code and hardware information are distributed under the GNU General Public Licence (GPL, version 3). Copyright © 2012 Elsevier B.V. All rights reserved.

Enhanced light extraction efficiency of GaN-based light-emittng diodes by nitrogen implanted current blocking layer

Energy Technology Data Exchange (ETDEWEB)

Kim, Yong Deok; Oh, Seung Kyu; Park, Min Joo; Kwak, Joon Seop, E-mail: jskwak@sunchon.ac.kr

2016-10-15

Highlights: • A nitrogen implanted current-blocking layer was successfully demonstrated. • Light-extraction efficiency and radiant intensity was increased by more than 20%. • Ion implantation was successfully implemented in GaN based light-emitting diodes. - Abstract: GaN-based light emitting diodes (LEDs) with a nitrogen implanted current-blocking layer (CBL) were successfully demonstrated for improving the light extraction efficiency (LEE) and radiant intensity. The LEE and radiant intensity of the LEDs with a shallow implanted CBL with nitrogen was greatly increased by more than 20% compared to that of a conventional LED without the CBL due to an increase in the effective current path, which reduces light absorption at the thick p-pad electrode. Meanwhile, deep implanted CBL with a nitrogen resulted in deterioration of the LEE and radiant intensity because of formation of crystal damage, followed by absorption of the light generated at the multi-quantum well(MQW). These results clearly suggest that ion implantation method, which is widely applied in the fabrication of Si based devices, can be successfully implemented in the fabrication of GaN based LEDs by optimization of implanted depth.

Thermal, spectral, and surface properties of LED light-polymerized bulk fill resin composites.

Science.gov (United States)

Pişkin, Mehmet Burçin; Atalı, Pınar Yılmaz; Figen, Aysel Kantürk

2015-02-01

The aim of this study was to evaluate the thermal, spectral, and surface properties of four different bulk fill materials – SureFil SDR (SDR, Dentsplay DETREY), QuixFil (QF, Dentsplay DETREY), X-tra base (XB, Voco) X-tra fil (XF, Voco) – polymerized by light-emitting diode (LED). Resin matrix, filler type, size and amount, and photoinitiator types influence the degree of conversion. LED-cured bulk fill composites achieved sufficient polymerization. Scanning electron microscope (SEM) analysis revealed different patterns of surface roughness, depending on the composite material. Bulk fill materials showed surface characteristics similar to those of nanohybrid composites. Based on the thermal analysis results, glass transition (T(g)) and initial degradation (T(i)) temperatures changed depending on the bulk fill resin composites.

Effects of blue diode laser (445 nm) and LED (430-480 nm) radiant heat treatments on dental glass ionomer restoratives

Science.gov (United States)

Dionysopoulos, Dimitrios; Tolidis, Kosmas; Strakas, Dimitrios; Gerasimou, Paris; Sfeikos, Thrasyvoulos; Gutknecht, Norbert

2018-02-01

The purpose of this in vitro study was to evaluate the effect of two radiant heat treatments on water sorption, solubility and surface roughness of three conventional glass ionomer cements by using a blue diode laser (445 nm) and a light emitting diode (LED) unit (430-480 nm). Thirty disk-shaped specimens were prepared for each tested GIC (Equia Fil, Ketac Universal Aplicap and Riva Self Cure). The experimental groups (n = 10) of the study were as follows: Group 1 was the control group, in Group 2 the specimens were irradiated for 60 s at the top surface using a LED light-curing unit and in Group 3 the specimens were irradiated for 60 s at the top surface using a blue light diode laser. Statistical analysis was performed using one-way ANOVA and Tukey post hoc tests at a level of significance of a = 0.05. Radiant heat treatments with both laser and LED devices significantly decreased water sorption and solubility (p tested GICs. Blue diode laser treatment was seemed to be more effective compared to LED treatment for some of the tested materials. There were no changes in surface roughness of the GICs after the treatments (p > 0.05). Among the tested materials there were differences in water sorption and solubility (p 0.05). The use of the blue diode laser for this radiant heat treatment was harmless for the surface of the tested GICs and may be advantageous for the longevity of their restorations.

Degree of conversion of resin-based materials cured with dual-peak or single-peak LED light-curing units.

Science.gov (United States)

Lucey, Siobhan M; Santini, Ario; Roebuck, Elizabeth M

2015-03-01

There is a lack of data on polymerization of resin-based materials (RBMs) used in paediatric dentistry, using dual-peak light-emitting diode (LED) light-curing units (LCUs). To evaluate the degree of conversion (DC) of RBMs cured with dual-peak or single-peak LED LCUs. Samples of Vit-l-escence (Ultradent) and Herculite XRV Ultra (Kerr) and fissure sealants Delton Clear and Delton Opaque (Dentsply) were prepared (n = 3 per group) and cured with either one of two dual-peak LCUs (bluephase(®) G2; Ivoclar Vivadent or Valo; Ultradent) or a single-peak (bluephase(®) ; Ivoclar Vivadent). High-performance liquid chromatography and nuclear magnetic resonance spectroscopy were used to confirm the presence or absence of initiators other than camphorquinone. The DC was determined using micro-Raman spectroscopy. Data were analysed using general linear model anova; α = 0.05. With Herculite XRV Ultra, the single-peak LCU gave higher DC values than either of the two dual-peak LCUs (P < 0.05). Both fissure sealants showed higher DC compared with the two RBMs (P < 0.05); the DC at the bottom of the clear sealant was greater than the opaque sealant, (P < 0.05). 2,4,6-trimethylbenzoyldiphenylphosphine oxide (Lucirin(®) TPO) was found only in Vit-l-escence. Dual-peak LED LCUs may not be best suited for curing non-Lucirin(®) TPO-containing materials. A clear sealant showed a better cure throughout the material and may be more appropriate than opaque versions in deep fissures. © 2014 BSPD, IAPD and John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Very High Frequency Resonant DC/DC Converters for LED Lighting

DEFF Research Database (Denmark)

Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

2013-01-01

This paper presents a very high frequency DC/DC converter for LED lighting. Several resonant topologies are compared and their usability discussed. At the end the resonant SEPIC converter is chosen based on the achievable power density and total bill of material. Simulations of a 51 MHz converter...... with 40 V input and 15 V output are made. The simulation shows possibility of achieving efficiency up to 87 % even with a HEXFET Power MOSFET. Three prototypes of the simulated converter are implemented showing good correlation with simulations. The prototypes have efficiencies up to 84 % and power...

III-nitride based light emitting diodes and applications

CERN Document Server

Han, Jung; Amano, Hiroshi; Morkoç, Hadis

2013-01-01

Light emitting diodes (LEDs) are already used in traffic signals, signage lighting, and automotive applications. However, its ultimate goal is to replace traditional illumination through LED lamps since LED lighting significantly reduces energy consumption and cuts down on carbon-dioxide emission. Despite dramatic advances in LED technologies (e.g., growth, doping and processing technologies), however, there remain critical issues for further improvements yet to be achieved for the realization of solid-state lighting. This book aims to provide the readers with some contemporary LED issues, which have not been comprehensively discussed in the published books and, on which the performance of LEDs is seriously dependent. For example, most importantly, there must be a breakthrough in the growth of high-quality nitride semiconductor epitaxial layers with a low density of dislocations, in particular, in the growth of Al-rich and and In-rich GaN-based semiconductors. The materials quality is directly dependent on th...

Effect of Interface Nanotexture on Light Extraction of InGaN-Based Green Light Emitting Diodes

International Nuclear Information System (INIS)

Yao-Bo, Pan; Sheng-Li, Qi; Hao, Fang; Guo-Yi, Zhang; Mao-Sheng, Hao

2010-01-01

We report the enhancement of the light extraction of InGaN-based green light emitting diodes (LEDs) via the interface nanotexturing. The texture consists of high-density nanocraters on the surface of a sapphire substrate with an in situ etching. The width of nanocraters is about 0.5 μm and the depth is around 0.1 μm. It is demonstrated that the LEDs with interface texture exhibit about a 27% improvement in luminance intensity, compared with standard LEDs. High power InGaN-based green LEDs are obtained by using the interface nanotexture. An optical ray-tracing simulation is performed to investigate the effect of interface nanotexture on light extraction. (cross-disciplinary physics and related areas of science and technology)

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

DEFF Research Database (Denmark)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter

2017-01-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum......, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on europium chelate as a fluorescent marker. The system performance was tested with the immunoassay based...... on the cardiac marker, TnI. The same signal-to-noise ratio as for the flash lamp based system was obtained, operating the LED below specified maximum current. The background counts of the system and its main contributors were measured and analyzed. The background of the system of the LED based unit was improved...

High power light emitting diode (LED) arrays versus halogen light polymerization of oral biomaterials: Barcol hardness, compressive strength and radiometric properties.

Science.gov (United States)

Mills, Robin W; Uhl, Alexander; Blackwell, Gordon B; Jandt, Klaus D

2002-07-01

The clinical performance of light polymerized dental composites is greatly influenced by the quality of the light curing unit (LCU) used. Commonly used halogen LCUs have some specific drawbacks such as decreasing light output with time. This may result in a low degree of monomer conversion of the composites with negative clinical implications. Previous studies have shown that blue light emitting diode (LED) LCUs have the potential to polymerize dental composites without having the drawbacks of halogen LCUs. Since these studies were carried out LED technology has advanced significantly and commercial LED LCUs are now becoming available. This study investigates the Barcol hardness as a function of depth, and the compressive strength of dental composites that had been polymerized for 40 or 20s with two high power LED LCU prototypes, a commercial LED LCU, and a commercial halogen LCU. In addition the radiometric properties of the LCUs were characterized. The two high power prototype LED LCUs and the halogen LCU showed a satisfactory and similar hardness-depth performance whereas the hardness of the materials polymerized with the commercial LED LCU rapidly decreased with sample depth and reduced polymerization time (20 s). There were statistically significant differences in the overall compressive strengths of composites polymerized with different LCUs at the 95% significance level (p = 0.0016) with the two high power LED LCU prototypes and the halogen LCU forming a statistically homogenous group. In conclusion, LED LCU polymerization technology can reach the performance level of halogen LCUs. One of the first commercial LED LCUs however lacked the power reserves of the high power LED LCU prototypes.

LED based opto-wetting platforms for micromixing

Science.gov (United States)

Thomas, Tony; Narayanan Unni, Harikrishnan

2018-02-01

The digital microfluidics utilizes the gradient in wettability for droplet transportation. This paper reports a novel technique of LED induced wetting ( Opto-wetting) where a single low power LED (Light emitting diode) emitting light of wavelength 395nm peak with luminous intensity of 300mcd (milli candela) is used to move two droplets of 20μL each on a photo responsive substrate of azobenzene (C12H10N2) coated PDMS (Poly Dimethyl Siloxane) substrate. The PDMS substrate of size 5cmx2cmx0.5cm were modified by thin film coating of Azobenzene dissolved in olive oil solution. The LED was aligned vertically on the top of the substrate. The pulsed operation of LED induces a spatial gradient of surface energy due to the reversible process of photo isomerization of Azobenzene molecules coated on the surface. The Photo-isomerization changes the conformation of the molecules thereby changing its surface energy .The change in surface energy of the substrate induces a change in contact angle of the droplet which initiates its movement. Two water droplets each of 20μL were dispensed on the substrate using micro syringe. Two droplets which were initially at a few cm distance apart were gradually moved towards the focus of light and merged together. The urine droplets (20μL) were moved and mixed with the red dye reagent (20μL) by controlling the light intensity of the LED. This concept provides a cost effective technique of droplet manipulation in the Lab on a chip domain where various multiplexed operations on proteins and DNA droplets can be done for point of care diagnostics.

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

Science.gov (United States)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Pedersen, Christian

2017-02-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on europium chelate as a fluorescent marker. The system performance was tested with the immunoassay based on the cardiac marker, TnI. The same signal-to-noise ratio as for the flash lamp based system was obtained, operating the LED below specified maximum current. The background counts of the system and its main contributors were measured and analyzed. The background of the system of the LED based unit was improved by 39% compared to that of the Xenon flash lamp based unit, due to the LEDs narrower emission spectrum and longer pulse width. Key parameters of the LED system are discussed to further optimize the signal-to-noise ratio and signal-to-background, and hence the sensitivity of the instrument.

Optimized lighting method of applying shaped-function signal for increasing the dynamic range of LED-multispectral imaging system

Science.gov (United States)

Yang, Xue; Hu, Yajia; Li, Gang; Lin, Ling

2018-02-01

This paper proposes an optimized lighting method of applying a shaped-function signal for increasing the dynamic range of light emitting diode (LED)-multispectral imaging system. The optimized lighting method is based on the linear response zone of the analog-to-digital conversion (ADC) and the spectral response of the camera. The auxiliary light at a higher sensitivity-camera area is introduced to increase the A/D quantization levels that are within the linear response zone of ADC and improve the signal-to-noise ratio. The active light is modulated by the shaped-function signal to improve the gray-scale resolution of the image. And the auxiliary light is modulated by the constant intensity signal, which is easy to acquire the images under the active light irradiation. The least square method is employed to precisely extract the desired images. One wavelength in multispectral imaging based on LED illumination was taken as an example. It has been proven by experiments that the gray-scale resolution and the accuracy of information of the images acquired by the proposed method were both significantly improved. The optimum method opens up avenues for the hyperspectral imaging of biological tissue.

Color-filter-free spatial visible light communication using RGB-LED and mobile-phone camera.

Science.gov (United States)

Chen, Shih-Hao; Chow, Chi-Wai

2014-12-15

A novel color-filter-free visible-light communication (VLC) system using red-green-blue (RGB) light emitting diode (LED) and mobile-phone camera is proposed and demonstrated for the first time. A feature matching method, which is based on the scale-invariant feature transform (SIFT) algorithm for the received grayscale image is used instead of the chromatic information decoding method. The proposed method is simple and saves the computation complexity. The signal processing is based on the grayscale image computation; hence neither color-filter nor chromatic channel information is required. A proof-of-concept experiment is performed and high performance channel recognition is achieved.

Using Pre-TMIn Treatment to Improve the Optical Properties of Green Light Emitting Diodes

Directory of Open Access Journals (Sweden)

Bing Xu

2014-01-01

Full Text Available We investigated the effects of pre-TMIn treatment on the optical properties of green light emitting diodes (LEDs. Although pre-TMIn treatment did not affect the epitaxial structure of quantum wells, it significantly improved the quality of the surface morphology relative to that of the untreated sample. Indium cluster can be seen by high-resolution transmission electron microscopy (HR-TEM, which is the explanation for the red-shift of photoluminescence (PL. Time-resolved photoluminescence measurements indicated that the sample prepared with pre-TMIn treatment had a shorter radiative decay time. As a result, the light output power of the treated green LED was higher than that of the conventional untreated one. Thus, pre-TMIn treatment appears to be a simple and efficient means of improving the performance of green LEDs.

Vision communications based on LED array and imaging sensor

Science.gov (United States)

Yoo, Jong-Ho; Jung, Sung-Yoon

2012-11-01

In this paper, we propose a brand new communication concept, called as "vision communication" based on LED array and image sensor. This system consists of LED array as a transmitter and digital device which include image sensor such as CCD and CMOS as receiver. In order to transmit data, the proposed communication scheme simultaneously uses the digital image processing and optical wireless communication scheme. Therefore, the cognitive communication scheme is possible with the help of recognition techniques used in vision system. By increasing data rate, our scheme can use LED array consisting of several multi-spectral LEDs. Because arranged each LED can emit multi-spectral optical signal such as visible, infrared and ultraviolet light, the increase of data rate is possible similar to WDM and MIMO skills used in traditional optical and wireless communications. In addition, this multi-spectral capability also makes it possible to avoid the optical noises in communication environment. In our vision communication scheme, the data packet is composed of Sync. data and information data. Sync. data is used to detect the transmitter area and calibrate the distorted image snapshots obtained by image sensor. By making the optical rate of LED array be same with the frame rate (frames per second) of image sensor, we can decode the information data included in each image snapshot based on image processing and optical wireless communication techniques. Through experiment based on practical test bed system, we confirm the feasibility of the proposed vision communications based on LED array and image sensor.

Garden's lighting by led-luminaries supplied by photovoltaic

International Nuclear Information System (INIS)

Vasilev, H.; Angelov, A.; Ganchev, G.

2006-01-01

The implementation of the project by investment entirely of Denima 2001 Ltd. for garden illumination of the part of the public garden 'Studentski' is consider. The illumination installation is implemented by PV batteries and by luminaries made up by fluorescent laps and LED. The goals of this pilot project are to make a comparative analyses and observation for the operation of the light system for future development

Bonding bare die LEDs on PET foils for lighting applications: Thermal design modeling and bonding experiments

NARCIS (Netherlands)

Ende, D.A. van den; Kusters, R.H.L.; Cauwe, M.; Waal, A. van der; Brand, J. van den

2012-01-01

Integration of LEDs on flexible foil substrates is of interest for flexible lighting applications and flexible photonic devices. A matrix of LEDs on a foil combined with a diffuser can be a potential alternative for flexible OLED lighting devices. Preferably, these LEDs are integrated in an

340nm UV LED excitation in time-resolved fluorescence system for europium-based immunoassays detection

OpenAIRE

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Pedersen, Christian

2017-01-01

In immunoassay analyzers for in-vitro diagnostics, Xenon flash lamps have been widely used as excitation light sources. Recent advancements in UV LED technology and its advantages over the flash lamps such as smaller footprint, better wall-plug efficiency, narrow emission spectrum, and no significant afterglow, have made them attractive light sources for gated detection systems. In this paper, we report on the implementation of a 340 nm UV LED based time-resolved fluorescence system based on ...

Catalyst-free activation of peroxides under visible LED light irradiation through photoexcitation pathway

Energy Technology Data Exchange (ETDEWEB)

Gao, Yaowen [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Shenzhen Research Institute of Wuhan University, Shenzhen, 518057 (China); Li, Yixi; Yao, Linyu; Li, Simiao; Liu, Jin [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Zhang, Hui, E-mail: eeng@whu.edu.cn [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Shenzhen Research Institute of Wuhan University, Shenzhen, 518057 (China)

2017-05-05

Highlights: • Persulfate could decolorize Rhodamine B (RhB) directly via non-radical reactions. • LED lamps emitting white light were utilized as the visible light source. • Dyes could activate peroxides through photoexcitation pathway. • Decolorization of dyes and production of radicals were achieved simultaneously. • The catalyst-free peroxide/dye/Vis process was effective in a broad pH range. - Abstract: Catalysts are known to activate peroxides to generate active radicals (i.e., hydroxyl radical (·OH) and sulfate radical (SO{sub 4}·{sup −})) under certain conditions, but the activation of peroxides in the absence of catalysts under visible light irradiation has been rarely reported. This work demonstrates a catalyst-free activation of peroxides for the generation of ·OH and/or SO{sub 4}·{sup −} through photoexcited electron transfer from organic dyes to peroxides under visible LED light irradiation, where Rhodamine B (RhB) and Eosin Y (EY) were selected as model dyes. The formation of ·OH and/or SO{sub 4}·{sup −} in the reactions and the electron transfer from the excited dyes to peroxides were validated via electron paramagnetic resonance (EPR), photoluminescence (PL) spectra and cyclic voltammetry (CV). The performance of the peroxide/dye/Vis process was demonstrated to be altered depending on the target substrate. Meanwhile, the peroxide/dye/Vis process was effective for simultaneous decolorization of dyes and production of active radicals under neutral even or basic conditions. The findings of this study clarified a novel photoexcitation pathway for catalyst-free activation of peroxides under visible light irradiation, which could avoid the secondary metal ion (dissolved or leached) pollution from the metal-based catalysts and expand the application range of the peroxide-based catalytic process.

High-Efficiency Nitride-Based Solid-State Lighting

Energy Technology Data Exchange (ETDEWEB)

Paul T. Fini; Shuji Nakamura

2005-07-30

In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 {micro}m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of {approx} 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light

Collimating lens for light-emitting-diode light source based on non-imaging optics.

Science.gov (United States)

Wang, Guangzhen; Wang, Lili; Li, Fuli; Zhang, Gongjian

2012-04-10

A collimating lens for a light-emitting-diode (LED) light source is an essential device widely used in lighting engineering. Lens surfaces are calculated by geometrical optics and nonimaging optics. This design progress does not rely on any software optimization and any complex iterative process. This method can be used for any type of light source not only Lambertian. The theoretical model is based on point source. But the practical LED source has a certain size. So in the simulation, an LED chip whose size is 1 mm*1 mm is used to verify the feasibility of the model. The mean results show that the lenses have a very compact structure and good collimating performance. Efficiency is defined as the ratio of the flux in the illuminated plane to the flux from LED source without considering the lens material transmission. Just investigating the loss in the designed lens surfaces, the two types of lenses have high efficiencies of more than 90% and 99%, respectively. Most lighting area (possessing 80% flux) radii are no more than 5 m when the illuminated plane is 200 m away from the light source.

Computer numerical control (CNC) lithography: light-motion synchronized UV-LED lithography for 3D microfabrication

International Nuclear Information System (INIS)

Kim, Jungkwun; Allen, Mark G; Yoon, Yong-Kyu

2016-01-01

This paper presents a computer-numerical-controlled ultraviolet light-emitting diode (CNC UV-LED) lithography scheme for three-dimensional (3D) microfabrication. The CNC lithography scheme utilizes sequential multi-angled UV light exposures along with a synchronized switchable UV light source to create arbitrary 3D light traces, which are transferred into the photosensitive resist. The system comprises a switchable, movable UV-LED array as a light source, a motorized tilt-rotational sample holder, and a computer-control unit. System operation is such that the tilt-rotational sample holder moves in a pre-programmed routine, and the UV-LED is illuminated only at desired positions of the sample holder during the desired time period, enabling the formation of complex 3D microstructures. This facilitates easy fabrication of complex 3D structures, which otherwise would have required multiple manual exposure steps as in the previous multidirectional 3D UV lithography approach. Since it is batch processed, processing time is far less than that of the 3D printing approach at the expense of some reduction in the degree of achievable 3D structure complexity. In order to produce uniform light intensity from the arrayed LED light source, the UV-LED array stage has been kept rotating during exposure. UV-LED 3D fabrication capability was demonstrated through a plurality of complex structures such as V-shaped micropillars, micropanels, a micro-‘hi’ structure, a micro-‘cat’s claw,’ a micro-‘horn,’ a micro-‘calla lily,’ a micro-‘cowboy’s hat,’ and a micro-‘table napkin’ array. (paper)

Degree of conversion of resin-based orthodontic bonding materials cured with single-wave or dual-wave LED light-curing units.

Science.gov (United States)

Santini, Ario; McGuinness, Niall; Nor, Noor Azreen Md

2014-12-01

To evaluate the degree of conversion (DC) of orthodontic adhesives (RBOAs) cured with dual peak or single peak light-emitting diode (LED) light-curing units (LCUs). Standardized samples of RBOAs, APCPlus, Opal® Bond® and LightBond(TM) were prepared (n = 3) and cured with one of two dual peak LCUs (bluephase® G2-Ivoclar-Vivadent or Valo-Ultradent) or a single peak control (bluephase® Ivoclar-Vivadent). The DC was determined using micro-Raman spectroscopy. The presence or absence of initiators other than camphorquinone was confirmed by high-performance liquid chromatography and nuclear magnetic resonance spectroscopy. Data were analysed using general linear model in Minitab 15 (Minitab Inc., State College, PA, USA). There was no significant difference in DC between APCPlus, and Opal® Bond (confidence interval: -3.89- to 2.48); significant difference between APCPlus and LightBond(TM) (-18.55 to -12.18) and Opal® Bond and Lightbond(TM) (-17.85 to -11.48); no significant difference between bluephase (single peak) and dual peak LCUs, bluephase G2 (-4.896 to 1.476) and Valo (-3.935 to 2.437) and between bluephase G2 and Valo (-2.225 to 4.147). APCPlus and Opal® Bond showed higher DC values than LightBond(TM) (P<0.05). Lucirin® TPO was found only in Vit-l-escence. Lucirin® TPO was not identified in the three orthodontic adhesives. All three LCUs performed similarly with the orthodontic adhesives: orthodontic adhesive make had a greater effect on DC than the LCUs. It is strongly suggested that manufacturers of resin-based orthodontic materials test report whether or not dual peak LCUs should be used with their materials. Dual peak LED LCUs, though suitable in the majority of cases, may not be recommended for certain non Lucirin® TPO-containing materials. © 2014 British Orthodontic Society.

A randomized, placebo-controlled, single-blinded, split-faced clinical trial evaluating the efficacy and safety of KLOX-001 gel formulation with KLOX light-emitting diode light on facial rejuvenation

Directory of Open Access Journals (Sweden)

Nikolis A

2016-05-01

Full Text Available Andreas Nikolis,1 Steven Bernstein,2 Brian Kinney,3 Nicolo Scuderi,4 Shipra Rastogi,5 John S Sampalis6 1Victoria Park, Plastic Surgery Section, Westmount, QC, Canada; 2Dermatology Department, University of Montreal Health Centre, Montreal, QC, Canada; 3Department of Plastic Surgery, USC School of Medicine, Beverley Hills, CA, USA; 4Department of Plastic and Reconstructive Surgery, La Sapienza, Rome, Italy; 5KLOX Technologies, Laval, 6JSS Medical Research, Montreal, QC, Canada Purpose: Many treatment modalities exist to counteract the effects of cutaneous aging. Ablative methods have been the mainstay for nonsurgical facial rejuvenation. In recent years, nonablative techniques have been developed with the aim of achieving facial rejuvenation without epidermal damage. Light-emitting diode (LED photorejuvenation is a novel nonablative technique that induces collagen synthesis through biophotomodulatory pathways. Materials and methods: A single-center, randomized, single-blinded, placebo-controlled, split-faced clinical trial was designed. Thirty-two patients were enrolled for a 12-week study. Patients were randomized into one of four groups: Group A, treatment with KLOX-001 gel formulation and white LED (placebo light; Group B, treatment with a placebo/base gel (no active chromophore formulation and KLOX LED light; Group C, treatment with KLOX-001 gel formulation and KLOX LED light; and Group D, treatment with the standard skin rejuvenating treatment (0.1% retinol-based cream. Patients received treatment at weeks 0, 1, 2, and 3, and returned to the clinic at weeks 4, 8, and 12 for clinical assessments performed by an independent, blinded committee of physicians using subjective clinician assessment scales. Tolerability, adverse outcomes, and patient satisfaction were also assessed. Results: Analysis demonstrated that the KLOX LED light with KLOX placebo/base gel and the KLOX LED light + KLOX-001 gel formulation groups were superior to standard of

Bilirubin isomer distribution in jaundiced neonates during phototherapy with LED light centered at 497 nm (turquoise) vs. 459 nm (blue).

Science.gov (United States)

Ebbesen, Finn; Madsen, Poul H; Vandborg, Pernille K; Jakobsen, Lasse H; Trydal, Torleif; Vreman, Hendrik J

2016-10-01

Phototherapy using blue light is the treatment of choice worldwide for neonatal hyperbilirubinemia. However, treatment with turquoise light may be a desirable alternative. Therefore, the aim of this randomized, controlled study was to compare the bilirubin isomer distribution in serum of jaundiced neonates after 24 h of therapy with narrow-band (LED) light centered at 497 nm (turquoise) vs. 459 nm (blue), of essentially equal irradiance. Eighty-three neonates (≥33 wk gestational age) with uncomplicated hyperbilirubinemia were included in the study. Forty neonates were exposed to light centered at 497 nm and 43 infants with light centered at 459 nm. Irradiances were 5.2 × 10(15) and 5.1 × 10(15) photons/cm(2)/s, respectively. After 24 h of treatment no significant differences in serum concentrations of total bilirubin isomers and Z,Z-bilirubin were observed between the 2 groups. Interestingly, concentrations of Z,E-bilirubin, and thus also total bilirubin isomers formed during therapy, were highest for infants receiving light centered at 459 nm, while the concentration of E,Z-bilirubin was highest for those receiving light centered at 497 nm. No significant difference was found between concentrations of E,Z-lumirubin. Therapy with LED light centered at 497 nm vs. 459 nm, applied with equal irradiance on the infants, resulted in a different distribution of bilirubin isomers in serum.

BiliLED low cost neonatal phototherapy, from prototype to industry

Energy Technology Data Exchange (ETDEWEB)

Geido, Daniel; Failache, Horacio [Instituto de Fisica de la Facultad de Ingenieria - Universidad de la Republica, Montevideo (Uruguay); Simini, Franco [Nucleo de Ingenieria Biomedica de las Facultades de Medicina e Ingenieria (Uruguay); Hospital de ClInicas. Av Italia S/N. Piso 15 sala 2, 11600 Montevideo (Uruguay)

2007-11-15

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14x14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described.

BiliLED low cost neonatal phototherapy, from prototype to industry

Science.gov (United States)

Geido, Daniel; Failache, Horacio; Simini, Franco

2007-11-01

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14×14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described.

BiliLED low cost neonatal phototherapy, from prototype to industry

International Nuclear Information System (INIS)

Geido, Daniel; Failache, Horacio; Simini, Franco

2007-01-01

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14x14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described

Morning Versus Evening Bright Light Treatment at Home to Improve Function and Pain Sensitivity for Women with Fibromyalgia: A Pilot Study.

Science.gov (United States)

Burgess, Helen J; Park, Margaret; Ong, Jason C; Shakoor, Najia; Williams, David A; Burns, John

2017-01-01

To test the feasibility, acceptability, and effects of a home-based morning versus evening bright light treatment on function and pain sensitivity in women with fibromyalgia. A single blind randomized study with two treatment arms: 6 days of a 1 hour morning light treatment or 6 days of a 1 hour evening light treatment. Function, pain sensitivity, and circadian timing were assessed before and after treatment. Participants slept at home, except for two nights in Sleep Center. Ten women meeting the American College of Rheumatology's diagnostic criteria for fibromyalgia, including normal blood test results. Self-reported function was assessed with the Fibromyalgia Impact Questionnaire (FIQ). Pain sensitivity was assessed using a heat stimulus that gave measures of threshold and tolerance. Circadian timing was assessed with the dim light melatonin onset. Both morning and evening light treatments led to improvements in function and pain sensitivity. However, only the morning light treatment led to a clinically meaningful improvement in function (>14% reduction from baseline FIQ) and morning light significantly increased pain threshold more than evening light ( P  treatment appears to be a feasible and acceptable adjunctive treatment to women with fibromyalgia. Those who undergo morning light treatment may show improvements in function and pain sensitivity. Advances in circadian timing may be one mechanism by which morning light improves pain sensitivity. Findings can inform the design of a randomized controlled trial. © 2016 American Academy of Pain Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

A new method to manipulate broiler chicken growth and metabolism: Response to mixed LED light system

Science.gov (United States)

Yang, Yefeng; Yu, Yonghua; Pan, Jinming; Ying, Yibin; Zhou, Hong

2016-05-01

Present study introduced a new method to manipulate broiler chicken growth and metabolism by mixing the growth-advantage LED. We found that the green/blue LED mixed light system (G-B and G × B) have the similar stimulatory effect on chick body weight with single green light and single blue light (G and B), compared with normal artificial light (P = 0.028). Moreover, the percentage of carcass was significantly greater in the mixed light (G × B) when compared with the single light (P = 0.003). Synchronized with body weight, the mixed light (G-B and G × B) had a significant improved influence on the feed conversion of birds compared with normal light (P = 0.002). A significant improvement in feed conversion were found in mixed light (G × B) compared with single LED light (P = 0.037). G group resulted in a greater high-density lipoprotein cholesterol level than B group (P = 0.002), whereas B group resulted in a greater low-density lipoprotein cholesterol level than G group (P = 0.017). The mixed light significantly increased the birds’ glucose level in comparison with the single light (P = 0.003). This study might establish an effective strategy for maximizing growth of chickens by mixed LED technology.

Monochromatic light-emitting diode (LED source in layers hens during the second production cycle

Directory of Open Access Journals (Sweden)

Rodrigo Borille

2015-09-01

Full Text Available ABSTRACTLight is an important environmental factor for birds, allowing not only their vision, but also influencing their physiological responses, such as behavioral and reproductive activity. The objective of this experiment was to evaluate the impact of different colors of monochromatic light (LED sources in laying hens production during the second laying cycle. The study was conducted in an experimental laying house during 70 days. A total of 300 laying hens Isa Brown® genetic strain, aged 95 weeks, in the second laying cycle were used in the study. The artificial light sources used were blue, yellow, green, red and white. The light regimen was continuous illumination of 17 h per day (12 h natural and 5 h artificial in a daily light regimen of 17L:5D (light: dark. The Latin Square design was adopted with five treatments (five colors divided into five periods, and five boxes, with six replicates of ten birds in each box. The production and egg quality were evaluated. The different colors of light source did not affect production parameters or egg quality (p > 0.05. The monochromatic light source may be considered as an alternative to artificial lighting in laying hens during the second production cycle.

Light-based therapies in acne treatment

Science.gov (United States)

Pei, Susan; Inamadar, Arun C.; Adya, Keshavmurthy A.; Tsoukas, Maria M.

2015-01-01

The use of light and laser in the treatment of acne is increasing as these modalities are safe, effective, and associated with no or minimal complications when used appropriately. These light and laser sources are also being used in combination with pharmacological and/or physical measures to synergize their effects and optimize the therapeutic outcome. This review focuses on optical devices used in treating acne and serves to delineate the current application of various methods, including their utility and efficacy. PMID:26009707

Improvement of illumination uniformity for LED flat panel light by using micro-secondary lens array.

Science.gov (United States)

Lee, Hsiao-Wen; Lin, Bor-Shyh

2012-11-05

LED flat panel light is an innovative lighting product in recent years. However, current flat panel light products still contain some drawbacks, such as narrow lighting areas and hot spots. In this study, a micro-secondary lens array technique was proposed and applied for the design of the light guide surface to improve the illumination uniformity. By using the micro-secondary lens array, the candela distribution of the LED flat panel light can be adjusted to similar to batwing distribution to improve the illumination uniformity. The experimental results show that the enhancement of the floor illumination uniformity is about 61%, and that of the wall illumination uniformity is about 20.5%.

Fluorescence image excited by a scanning UV-LED light

Science.gov (United States)

Tsai, Hsin-Yi; Chen, Yi-Ju; Huang, Kuo-Cheng

2013-03-01

An optical scanning system using UV-LED light to induced fluorescence technology can enhance a fluorescence image significantly in a short period. It has several advantages such as lower power consumption, no scattering effect in skins, and multilayer images can be obtained to analyze skin disease. From the experiment results, the light intensity increases with increase spot size and decrease scanning speed, but the image resolution is oppositely. Moreover, the system could be widely used in clinical diagnosis and photodynamic therapy for skin disease because even the irradiated time of fluorescence substance is short but it will provide accurately positioning of fluorescence object.

High-power LEDs for plant cultivation

Science.gov (United States)

Tamulaitis, Gintautas; Duchovskis, Pavelas; Bliznikas, Zenius; Breive, Kestutis; Ulinskaite, Raimonda; Brazaityte, Ausra; Novickovas, Algirdas; Zukauskas, Arturas; Shur, Michael S.

2004-10-01

We report on high-power solid-state lighting facility for cultivation of greenhouse vegetables and on the results of the study of control of photosynthetic activity and growth morphology of radish and lettuce imposed by variation of the spectral composition of illumination. Experimental lighting modules (useful area of 0.22 m2) were designed based on 4 types of high-power light-emitting diodes (LEDs) with emission peaked in red at the wavelengths of 660 nm and 640 nm (predominantly absorbed by chlorophyll a and b for photosynthesis, respectively), in blue at 455 nm (phototropic function), and in far-red at 735 nm (important for photomorphology). Morphological characteristics, chlorophyll and phytohormone concentrations in radish and lettuce grown in phytotron chambers under lighting with different spectral composition of the LED-based illuminator and under illumination by high pressure sodium lamps with an equivalent photosynthetic photon flux density were compared. A well-balanced solid-state lighting was found to enhance production of green mass and to ensure healthy morphogenesis of plants compared to those grown using conventional lighting. We observed that the plant morphology and concentrations of morphologically active phytohormones is strongly affected by the spectral composition of light in the red region. Commercial application of the LED-based illumination for large-scale plant cultivation is discussed. This technology is favorable from the point of view of energy consumption, controllable growth, and food safety but is hindered by high cost of the LEDs. Large scale manufacturing of high-power red AlInGaP-based LEDs emitting at 650 nm and a further decrease of the photon price for the LEDs emitting in the vicinity of the absorption peak of chlorophylls have to be achieved to promote horticulture applications.

Performance of the mixed LED light quality on the growth and energy efficiency of Arthrospira platensis.

Science.gov (United States)

Mao, Ruixin; Guo, Shuangsheng

2018-06-01

The effect of mixed light quality with red, blue, and green LED lamps on the growth of Arthrospira platensis was studied, so as to lay the theoretical and technical basis for establishing a photo-bioreactor lighting system for application in space. Meanwhile, indexes, like morphology, growth rate, photosynthetic pigment compositions, energy efficiency, and main nutritional components, were measured respectively. The results showed that the blue light combined with red light could decrease the tightness of filament, and the effect of green light was opposite. The combination of blue light or green light with red light induced the filaments to get shorter in length. The 8R2B treatment could promote the growth of Arthrospira platensis significantly, and its dry weight reached 1.36 g L -1 , which was 25.93% higher than the control. What's more, 8R2B treatment had the highest contents of carbohydrate and lipid, while 8R2G was rich in protein. 8R0.5G1.5B had the highest efficiency of biomass production, which was 161.53 mg L -1  kW -1  h -1 . Therefore, the combination of red and blue light is more conducive to the growth of Arthrospira platensis, and a higher biomass production and energy utilization efficiency can be achieved simultaneously under the mixed light quality with the ratio of 8R0.5G1.5B.

Investigation of illumination efficiency on the LED therapy with different array types

Science.gov (United States)

Chen, Hsi-Chao; Liou, Cheng-Jyun

2009-08-01

Light-emitting diodes (LEDs) are a major discovery in twenty-one century for its advantages including small size, long lifetime, low voltage, high response and good mechanical properties. It is an environment-friendly product and maybe becomes a lighting source in future. In the other way LED lighting also is used for the lighting source of cosmetology. LED phototherapy provided medicine with a new tool capable of delivering light deep into tissues of the body, at wavelengths that are biologically optimal for pain treatment and holistic healing. The illumination efficiency is one of the key indexes for the LED phototherapy. LEDs were arranged on a disk of diameter of 100mm with different array types: a radial, a rhombus, an octagon, and a square. Then the LEDs with view angle of 120 degree were used for the lighting sources. Trace-Pro software was used for the optical simulation. The array types of radial and square were better than those of rhombus and octagon for illumination efficiency. In the mixture efficiency of a radial array was observed by different distances from 1mm to 100mm. However lighting could reach the well mixture after the treatment distance of 30mm by optical simulation. The view angle could reach +/-60 degree at the treatment distance of 50 mm for the LED phototherapy mockup.

Knoop hardness of ten resin composites irradiated with high-power LED and quartz-tungsten-halogen lights.

Science.gov (United States)

Price, Richard B T; Felix, Corey A; Andreou, Pantelis

2005-05-01

This study compared a high-power light-emitting-diode (LED) curing light (FreeLight 2, 3M ESPE) with a quartz-tungsten-halogen (QTH) light (TriLight, 3M ESPE) to determine which was the better at photo-polymerising 10 resin composites. Class I preparations were prepared 4-mm deep into human teeth and filled with 10 different composites. The composites were irradiated for 50% or 100% of their recommended times using the LED light, and for 100% of their recommended times with the QTH light on either the high or medium power setting. Fifteen minutes later, the Knoop hardness of the composites was measured to a depth of 3.5 mm from the surface. When irradiated by the LED light for their recommended curing times, the Knoop hardness of all 10 composites stayed above 80% of the maximum hardness of the composite to a depth of at least 1.5 mm; three composites maintained a Knoop hardness that was more than 80% of their maximum hardness to a depth of 3.5 mm. Repeated measurements analysis of variance indicated that all the two-way and three-way interactions between the curing light, depth, and composite were significant (p hardness values. The LED light, used for the composite manufacturer's recommended time, was ranked the best at curing the composites to a depth of 3mm (p power setting.

Artificial LED lighting enhances growth characteristics and total phenolic content of Ocimum basilicum, but variably affects transplant success

OpenAIRE

Bantis, Filippos; Ouzounis, Theoharis; Radoglou, Kalliopi

2016-01-01

The morphological and phytochemical characteristics of two Ocimum basilicum cultivars (Lettuce Leaf, and Red Rubin-mountain Athos hybrid) under artificial lighting were investigated. Four LED light treatments [AP673L (high red and high red:far-red), G2 (high red and low red:far-red), AP67 (moderate blue and red and low red:far-red), and NS1 (high blue and green, high red:far-red and 1% ultraviolet)] with different colors mixing UV, blue, green, red and far-red, and fluorescent tubes (FL, high...

Rectangular illumination using a secondary optics with cylindrical lens for LED street light.

Science.gov (United States)

Chen, Hsi-Chao; Lin, Jun-Yu; Chiu, Hsuan-Yi

2013-02-11

The illumination pattern of an LED street light is required to have a rectangular distribution at a divergence-angle ratio of 7:3 for economical illumination. Hence, research supplying a secondary optics with two cylindrical lenses was different from free-form curvature for rectangular illumination. The analytical solution for curvatures with different ratio rectangles solved this detail by light tracing and boundary conditions. Similarities between the experiments and the simulation for a single LED and a 9-LED module were analyzed by Normalized Cross Correlation (NCC), and the error rate was studied by the Root Mean Square (RMS). The tolerance of position must be kept under ± 0.2 mm in the x, y and z directions to ensure that the relative illumination is over 99%.

Design of a lighting system with high-power LEDs, large area electronics, and light management structure in the LUMENTILE European project

Science.gov (United States)

Carraro, L.; Simonetta, M.; Benetti, G.; Tramonte, A.; Capelli, G.; Benedetti, M.; Randone, E. M.; Ylisaukko-oja, A.; Keränen, K.; Facchinetti, T.; Giuliani, G.

2017-02-01

LUMENTILE (LUMinous ElectroNic TILE) is a project funded by the European Commission with the goal of developing a luminous tile with novel functionalities, capable of changing its color and interact with the user. Applications include interior/exterior tile for walls and floors covering, high-efficiency luminaries, and advertising under the form of giant video screens. High overall electrical efficiency of the tile is mandatory, as several millions of square meters are foreseen to be installed each year. Demand is for high uniformity of the illumination of the top tile surface, and for high optical extraction efficiency. These features are achieved by smart light management, using a new approach based on light guiding slab and spatially selective light extraction obtained using both diffusion and/or reflection from the top and bottom interfaces of the optical layer. Planar and edge configurations for the RGB LEDs are considered and compared. A square shape with side length from 20cm to 60cm is considered for the tiles. The electronic circuit layout must optimize the electrical efficiency, and be compatible with low-cost roll-to-roll production on flexible substrates. LED heat management is tackled by using dedicated solutions that allow operation in thermally harsh environment. An approach based on OLEDs has also been considered, still needing improvement on emitted power and ruggedness.

Yuma Border Patrol Lighting Retrofit: Final LED System Performance Assessment of Trial and Full Installation

Energy Technology Data Exchange (ETDEWEB)

Andrea Wilkerson, Gregory P Sullivan, Robert G Davis, Sarah Safranek

2018-04-30

Along the Yuma Sector Border Patrol Area in Yuma, Arizona, the GATEWAY program conducted a trial evaluation in which the incumbent quartz metal halide area lighting was replaced with LED at three pole locations, and illuminance measurements were recorded initially and at 2500 hours, 5000 hours, 7000, and 11,000 hours of operation. Additionally, four second-generation LED luminaires installed as part of the full installation were evaluated initially and again after 4,000 hours of operation. While the initial energy, lighting quality, and maintenance benefits relative to the incumbent high-pressure sodium system were very satisfactory, the study raises important questions regarding the long-term performance of LED lighting systems in high-temperature environments.

LED lighting and the Next Generation of Greenhouse for Tomatoes. Proof of Principle; LED belichting en Het Nieuwe Telen bij tomaat. Proof of Principle

Energy Technology Data Exchange (ETDEWEB)

Dueck, T.; Janse, J.; Eveleens, B. [Wageningen UR Glastuinbouw, Wageningen (Netherlands); Nieboer, S.; Valstar, W.; Grootscholten, M. [GreenQ Improvement Centre, Bleiswijk (Netherlands)

2012-08-15

In this Proof of Principle project a tomato crop was grown under artificial lighting with the aim of 30% energy saving at the same level of production. Tomatoes (cultivar Komeett) were illuminated with 110 {mu}mol m{sup -2} s{sup -1} HPS (High Pressure Sodium) above the crop and 85 {mu}mol m{sup -2} s{sup -1} LED interlighting. The LEDs hung in 2 rows, approximately 40 cm above the lower leaves and the second strand at 40 or 70 cm above that. There were two types of LEDs used: production LEDs (light efficiency 1.6 {mu}mol m{sup -2} s{sup -1}, 87% red/13% blue) and inter-lighting LEDs (light efficiency 1.9 {mu}mol m{sup -2} s{sup -1}, 95% red/5% blue), with the same light intensity. At the start, the crop was given as much light as it could handle, and because the crop developed so well, the stem density was increased relatively early. This resulted in high fruit load, while insufficient light was available to compensate for the low levels of sunlight in the winter. In the 192 cm row spacing system the plants were too close to each other. Additional problems occurred with trace elements, lesser bumble bee activity, and a moist greenhouse climate which weakened the crop in the winter. Thus Botrytis occurred on the leaves and stems. The crop struggled with its recovery until early spring with more sunlight. Compared to a reference crop with 79 kg m{sup -2} tomatoes, 75 kg m{sup -2} were produced under-production LEDs, and 80 kg m{sup -2} under the interlighting LEDs, mainly because latter LEDs were used longer during the summer. 30% of the energy for dehumidification and heat energy, and 27% of the electricity was saved, relative to the reference crop. Thus it appears possible to save 30% energy with a near identical production [Dutch] In dit Proof of Principle project is een belichte tomatenteelt geteeld met als doel 30% energiebesparing bij een gelijke productie. Tomaten van het ras Komeett werden belicht met 110 {mu}mol m{sup -2} s{sup -1} SON-T belichting boven

GATEWAY Demonstrations: Philadelphia International Airport Apron Lighting: LED System Performance in a Trial Installation

Energy Technology Data Exchange (ETDEWEB)

Davis, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilkerson, Andrea M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-10-30

This report documents a trial installation of LED apron lighting that replaced the existing high-pressure sodium luminaires at Philadelphia International Airport. Such high-mast applications remain challenging for LED technology, and the lessons learned from this project may help facility managers and LED product manufacturers better meet those challenges.

Stakeholder Values and Perspectives when Implementing Led Lights on Navy Ships

Science.gov (United States)

2014-06-01

Human Factors in Lighting Freymiller, 2009, from Boyce, 2003) LEDs have no known cause of headaches due to flicker and the electronic magnetic...reoccurrence of dimming and flickering can reoccur. There should be further research conducted on how a headache affects the loss of productivity on...Walls, P. M. (2011, Dec). Eye disease resulting from increased use of fluorescent lighting as a climate change mitigation strategy. Retrieved from

Developing LED UV fluorescence sensors for online monitoring DOM and predicting DBPs formation potential during water treatment.

Science.gov (United States)

Li, Wen-Tao; Jin, Jing; Li, Qiang; Wu, Chen-Fei; Lu, Hai; Zhou, Qing; Li, Ai-Min

2016-04-15

Online monitoring dissolved organic matter (DOM) is urgent for water treatment management. In this study, high performance size exclusion chromatography with multi-UV absorbance and multi-emission fluorescence scans were applied to spectrally characterize samples from 16 drinking water sources across Yangzi River and Huai River Watersheds. The UV absorbance indices at 254 nm and 280 nm referred to the same DOM components and concentration, and the 280 nm UV light could excite both protein-like and humic-like fluorescence. Hence a novel UV fluorescence sensor was developed out using only one UV280 light-emitting diode (LED) as light source. For all samples, enhanced coagulation was mainly effective for large molecular weight biopolymers; while anion exchange further substantially removed humic substances. During chlorination tests, UVA280 and UVA254 showed similar correlations with yields of disinfection byproducts (DBPs); the humic-like fluorescence obtained from LED sensors correlated well with both trihalomethanes and haloacetic acids yields, while the correlation between protein-like fluorescence and trihalomethanes was relatively poor. Anion exchange exhibited more reduction of DBPs yields as well as UV absorbance and fluorescence signals than enhanced coagulation. The results suggest that the LED UV fluorescence sensors are very promising for online monitoring DOM and predicting DBPs formation potential during water treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of LED or laser phototherapy on bone defects grafted with MTA and irradiated with laser or LED light: a comparative Raman spectroscopic study

Science.gov (United States)

Pinheiro, Antonio L. B.; Soares, Luiz G. P.; Barbosa, Artur Felipe S.; Silveira, Landulfo, Jr.

2012-03-01

We studied peaks of calcium hydroxyapatite - CHA on defects grafted with MTA, treated or not with Light Emitting Diode - LED or IR Laser. 54 rats were divided in 6 groups each subdivided into 3 subgroups (15,21,30d). LED (λ850 +/- 10nm) or IR Laser (λ850 nm) was applied over (LED) or in 4 points around the defect at 48 h intervals for 15 days. Raman readings were taken at the surface of the defect. The smaller overall intensity of the peak was found in Group MTA + Laser (1510.2 +/- 274.1) and the highest on Group LED (2322 +/- 715). There were no statistically significant differences between non-irradiated subjects on regards the CHA peaks. On the other hand, there were statistically significant differences between the Group Clot and LED, Clot and Laser, and Clot and MTA + Laser (p =0.01, p = 0.02, p = 0.003). There were no significant differences between Group MTA and MTA + LED (p=0.2) but significant differences were seen between Groups MTA and MTA + Laser (p=0.01). Significant differences were also observed between Groups LED and Laser (p <0.001) and between Groups MTA + LED and MTA + Laser (p=0.009). MTA, due to its characteristics, seemed to be directly affected by the light. However, the use of either phototherapy positively affected bone healing similarly as observed on different studies using other biomaterials. The overall analysis of our results indicated that the use of either light source resulted in a better, more advanced, and of quality bone repair.

Lighting and social practices - what role does lighting play for low energy house (LEH) households and LED frontrunners?

DEFF Research Database (Denmark)

Jensen, Charlotte Louise

As lighting in Danish households consume approximately 1.3 TWh every year, reducing electricity consumption from lighting is important. Studies have shown that a mere substitution of inefficient lighting technologies towards more efficient ones may not be possible, as many social and cultural...... dimensions influence how people use and relate to lighting. Assessing how very distinctive contexts of households (that diverge from an exemplary kind of household), such as low energy houses and LED frontrunner households, use and understand lighting, may give some insight into what may trigger or hamper...

Broadcast of four HD videos with LED ceiling lighting: optical-wireless MAC

Science.gov (United States)

Bouchet, Olivier; Porcon, Pascal; Gueutier, Eric

2011-09-01

The European project "hOME Gigabit Access Network" (OMEGA) targeted various wireless and wired solutions for 1 Gbit/s connectivity in Home Area Networks (HANs). One objective was to evaluate the suitability of optical wireless technologies in two spectral regions: visible light (visible-light communications - VLC) and near infrared (infrared communications - IRC). Several demonstrators have been built, all of them largely relying on overthe- shelf components. The demonstrators included a "wide-area" VLC broadcast link based on LED ceiling lighting and a laser-based high-data-rate "wide-area" IRC prototype. In this paper we discuss an adapted optical-wireless media-access-control (OWMAC) sublayer, which was developed and implemented during the project. It is suitable for both IRC and VLC. The VLC prototype is based on DMT signal processing and provides broadcasting at { 100 Mbit/s over an area of approximately 5 m2. The IRC prototype provides {300 Mbit/s half-duplex communication over an area of approximately 30 m2. The IRC mesh network, composed of one base station and two terminals, is based on OOK modulation, multi-sector transceivers, and an ultra-fast sector switch. After a brief discussion about the design of the optical-wireless data link layer and the optical-wireless switch (OWS) card, we address the card development and implementation. We also present applications for the VLC and IRC prototypes and measurement results regarding the MAC layer.

Optimal LED-based illumination control via distributed convex optimization

NARCIS (Netherlands)

Aslam, Muhammad; Hermans, R.M.; Pandharipande, A.; Lazar, M.; Boje, Edward; Xia, Xiaohua

2014-01-01

Achieving illumination and energy consumption targets is essential in indoor lighting design. The provision of localized illumination to occupants, and the utilization of natural light and energy-efficient light-emitting diode (LED) luminaires can help meet both objectives. Localized illumination

LED Lighting – Modification of Growth, Metabolism, Yield and Flour Composition in Wheat by Spectral Quality and Intensity

Directory of Open Access Journals (Sweden)

István Monostori

2018-05-01

Full Text Available The use of light-emitting diode (LED technology for plant cultivation under controlled environmental conditions can result in significant reductions in energy consumption. However, there is still a lack of detailed information on the lighting conditions required for optimal growth of different plant species and the effects of light intensity and spectral composition on plant metabolism and nutritional quality. In the present study, wheat plants were grown under six regimens designed to compare the effects of LED and conventional fluorescent lights on growth and development, leaf photosynthesis, thiol and amino acid metabolism as well as grain yield and flour quality of wheat. Benefits of LED light sources over fluorescent lighting were manifested in both yield and quality of wheat. Elevated light intensities made possible with LEDs increased photosynthetic activity, the number of tillers, biomass and yield. At lower light intensities, blue, green and far-red light operated antagonistically during the stem elongation period. High photosynthetic activity was achieved when at least 50% of red light was applied during cultivation. A high proportion of blue light prolonged the juvenile phase, while the shortest flowering time was achieved when the blue to red ratio was around one. Blue and far-red light affected the glutathione- and proline-dependent redox environment in leaves. LEDs, especially in Blue, Pink and Red Low Light (RedLL regimens improved flour quality by modifying starch and protein content, dough strength and extensibility as demonstrated by the ratios of high to low molecular weight glutenins, ratios of glutenins to gliadins and gluten spread values. These results clearly show that LEDs are efficient for experimental wheat cultivation, and make it possible to optimize the growth conditions and to manipulate metabolism, yield and quality through modification of light quality and quantity.

Interaction of LED light with coinitiator-containing composite resins: effect of dual peaks.

Science.gov (United States)

Sim, Jae-Seong; Seol, Hyo-Joung; Park, Jeong-Kil; Garcia-Godoy, Franklin; Kim, Hyung-Il; Kwon, Yong Hoon

2012-10-01

Recently the colour stability of composite resins has been an issue due to the emphasis on the aesthetics of restored teeth. The purpose of the present study was to investigate how dual-peak LED units affect the polymerization of coinitiator-containing composite resins. Five composite resins [coinitiator-containing: Aelite LS Posterior (AL), Tetric EvoCeram (TE), and Vit-l-escence (VI); only CQ-containing: Grandio (GD) and Filtek Z350 (Z3)] were light cured using four different light-curing units (LCUs). Among them, Bluephase G2 (BP) and G-light (GL) were dual-peak LED LCUs. Microhardness, polymerization shrinkage, flexural, and compressive properties were measured. BP and GL had no consistent effect on the microhardness of AL, TE, and VI on the top and bottom surfaces of resin specimens. Among the specimens, AL and VI showed the least (9.86-10.41 μm) and greatest (17.58-19.21 μm) polymerization shrinkage, respectively. However, the effect of BP and GL on the shrinkage of specimens was not consistent. Among the specimens, GD showed the greatest flexural properties [strength (FS) and modulus (FM)] and TE showed the lowest flexural and compressive properties [strength (CS) and modulus (CM)]. In same resin product, maximum FS and CS differences due to the different LCUs were 10.3-21.0% and 3.6-9.2%, respectively. Furthermore, the influences of BP and GL on FS and CS were not consistent. The tested dual-peak LED LCUs had no consistent synergic effect on the polymerization of coinitiator-containing composite resins as compared with QTH and single-peak LED LCUs. The dual-peak LED LCUs achieve a similar degree of polymerization in coinitiator-composite resins as QTH and single-peak LED LCUs did. Choice of LCU does not appear to be a determinant of the light curing of coinitiator-composite resins. Copyright © 2012 Elsevier Ltd. All rights reserved.

'No blue' LED solution for photolithography room illumination

DEFF Research Database (Denmark)

Ou, Haiyan; Corell, Dennis Dan; Dam-Hansen, Carsten

2010-01-01

This paper explored the feasibility of using a LED-based bulb as the illumination light source for photolithography room. A no-blue LED was designed, and the prototype was fabricated. The spectral power distribution of both the LED bulb and the yellow fluorescent tube was measured. Based on that...... color rendering ability than the YFT. Furthermore, LED solution has design flexibility to improve it further. The prototype has been tested with photoresist SU8-2005. Even after 15 days of illumination, no effect was observed. So this LED-based solution was demonstrated to be a very promising light......, colorimetric values were calculated and compared on terms of chromatic coordinates, correlated color temperature, color rendering index, and chromatic deviation. Gretagmacbeth color charts were used as a more visional way to compare the two light sources, which shows that our no-blue LED bulb has much better...

Development and future of ultraviolet light-emitting diodes: UV-LED will replace the UV lamp

Science.gov (United States)

Muramoto, Yoshihiko; Kimura, Masahiro; Nouda, Suguru

2014-06-01

Ultraviolet light-emitting diodes (UV-LEDs) have started replacing UV lamps. The power per LED of high-power LED products has reached 12 W (14 A), which is 100 times the values observed ten years ago. In addition, the cost of these high-power LEDs has been decreasing. In this study, we attempt to understand the technologies and potential of UV-LEDs.

Application of 265-nm UVC LED Lighting to Sterilization of Typical Gram Negative and Positive Bacteria

Science.gov (United States)

Lee, Yong Wook; Yoon, Hyung Do; Park, Jae-Hyoun; Ryu, Uh-Chan

2018-05-01

UV LED lightings have been displacing conventional UV lamps due to their high efficiency, long lifetime, etc. A sterilizing lighting was prepared by assembling a UV LED module composed of 265-nm UVC LEDs and a silica lens array with a driver module comprised of a driver IC controlling pulse width modulation and constant current. The silica lens array was designed and fabricated to focus UV beam and simultaneously to give a uniform light distribution over specimens. Then pasteurizing effect of the lighting was analyzed for four kinds of bacteria and one yeast which are dangerous to people with low immunity. Sterilizing tests on these germs were carried out at the both exposure distances of 10 and 100 mm for various exposure durations up to 600 s.

Relationship between the change of ethological status and concentration of certain cytokines in blood in experimental desynchronosis under led lighting.

Science.gov (United States)

Osikov, M V; Ogneva, O I

2016-01-01

Changing the natural rhythm of day and night leads to the development of DS, disruption of coordinated muscular activity, adequate behavioral activity, a decrease of attention in the performance of night work by experts in various fields. Changes ethological status may potentiate or weaken the changes in the indices of immune status, contribute to the formation of allostatic load at desynchronosis. To investigate the relationship between changes ethological status and concentration of certain cytokines in peripheral blood in experimental desynchronosis under LED lighting. The study was performed on 158 adult guinea pigs, which were randomly assigned into 2 groups: 1 group- animals in the conditions of standard fixed (12 h light / 12 h dark) LED lighting (SFSDO); 2 group- animals with jet lag in terms of LED lighting (DESSDO). Light desynchronosis created by keeping animals at clock coverage for 30 days. Behavioral activity was studied in the test «open field» cognitive function was assessed using aqueous «labyrinth» Morris. By ELISA was determined on the apparatus in the peripheral blood concentration of interleukin - 4 (IL-4), interferon-gamma (IFN-g), melatonin, cortisol via specific for guinea pig test systems. It was found that in animals of DS in terms of LED lighting in the dynamics of 10-30 days of observation show signs of anxiety, depression orienting-exploratory behavior, reduce the long-term memory and learning ability, spatial orientation disorders. It found that when a jet lag LED lighting conditions for 10 days, 20 days and 30 days in peripheral blood melatonin concentration decreases, the concentration of cortisol rises. In peripheral blood decreased IL-4 concentrations of 20 and 30 days, reducing the concentration of IFN-g at 30 days. Based on the results of correlation analysis, ethological change status and progress of cognitive function with a decrease in the blood concentration of IL-4 and IFN-g, the concentration of melatonin increase

Potential environmental impacts of light-emitting diodes (LEDs): metallic resources, toxicity, and hazardous waste classification.

Science.gov (United States)

Lim, Seong-Rin; Kang, Daniel; Ogunseitan, Oladele A; Schoenung, Julie M

2011-01-01

Light-emitting diodes (LEDs) are advertised as environmentally friendly because they are energy efficient and mercury-free. This study aimed to determine if LEDs engender other forms of environmental and human health impacts, and to characterize variation across different LEDs based on color and intensity. The objectives are as follows: (i) to use standardized leachability tests to examine whether LEDs are to be categorized as hazardous waste under existing United States federal and California state regulations; and (ii) to use material life cycle impact and hazard assessment methods to evaluate resource depletion and toxicity potentials of LEDs based on their metallic constituents. According to federal standards, LEDs are not hazardous except for low-intensity red LEDs, which leached Pb at levels exceeding regulatory limits (186 mg/L; regulatory limit: 5). However, according to California regulations, excessive levels of copper (up to 3892 mg/kg; limit: 2500), Pb (up to 8103 mg/kg; limit: 1000), nickel (up to 4797 mg/kg; limit: 2000), or silver (up to 721 mg/kg; limit: 500) render all except low-intensity yellow LEDs hazardous. The environmental burden associated with resource depletion potentials derives primarily from gold and silver, whereas the burden from toxicity potentials is associated primarily with arsenic, copper, nickel, lead, iron, and silver. Establishing benchmark levels of these substances can help manufacturers implement design for environment through informed materials substitution, can motivate recyclers and waste management teams to recognize resource value and occupational hazards, and can inform policymakers who establish waste management policies for LEDs.

GaN-based integrated photonics chip with suspended LED and waveguide

Science.gov (United States)

Li, Xin; Wang, Yongjin; Hane, Kazuhiro; Shi, Zheng; Yan, Jiang

2018-05-01

We propose a GaN-based integrated photonics chip with suspended LED and straight waveguide with different geometric parameters. The integrated photonics chip is prepared by double-side process. Light transmission performance of the integrated chip verse current is quantitatively analyzed by capturing light transmitted to waveguide tip and BPM (beam propagation method) simulation. Reduction of the waveguide width from 8 μm to 4 μm results in an over linear reduction of the light output power while a doubling of the length from 250 μm to 500 μm only results in under linear decrease of the output power. Free-space data transmission with 80 Mbps random binary sequence of the integrated chip is capable of achieving high speed data transmission via visible light. This study provides a potential approach for GaN-based integrated photonics chip as micro light source and passive optical device in VLC (visible light communication).

Portable plant chlorophyll fluorimeter based on blue LED rapid induced technology

Science.gov (United States)

Zheng, Yibo; Mi, Ting; Zhang, Lei; Zhao, Jun

2018-01-01

Fluorimeter is an effective device for detecting chlorophyll a content in plants. In order to realize real-time nondestructive detection of plant blades, a camera based fluorescence instrument based on two color mirrors has been developed. The blue light LED is used as the excitation light source, and the lens is used for shaping and focusing the excitation light to ensure the excitation intensity and uniform illumination of the light source. The device uses a 45 degree two color mirror to separate the chlorophyll a excited light path and the fluorescence receiving light path. Finally, the fluorescent signal is collected by the silicon photocell, and the signal is processed by the circuit to transmit the digital information to the display. Through the analysis of the experimental data, the device has the advantages of small size, easy to carry, fast induction, etc., and can be widely applied in outdoor teaching and field investigation.

Smart LED allocation scheme for efficient multiuser visible light communication networks.

Science.gov (United States)

Sewaiwar, Atul; Tiwari, Samrat Vikramaditya; Chung, Yeon Ho

2015-05-18

In a multiuser bidirectional visible light communication (VLC), a large number of LEDs or an LED array needs to be allocated in an efficient manner to ensure sustainable data rate and link quality. Moreover, in order to support an increasing or decreasing number of users in the network, the LED allocation is required to be performed dynamically. In this paper, a novel smart LED allocation scheme for efficient multiuser VLC networks is presented. The proposed scheme allocates RGB LEDs to multiple users in a dynamic and efficient fashion, while satisfying illumination requirements in an indoor environment. The smart LED array comprised of RGB LEDs is divided into sectors according to the location of the users. The allocated sectors then provide optical power concentration toward the users for efficient and reliable data transmission. An algorithm for the dynamic allocation of the LEDs is also presented. To verify its effective resource allocation feature of the proposed scheme, simulations were performed. It is found that the proposed smart LED allocation scheme provides the effect of optical beamforming toward individual users, thereby increasing the collective power concentration of the optical signals on the desirable users and resulting in significantly increased data rate, while ensuring sufficient illumination in a multiuser VLC environment.

Implementation and Test of a LED-Based Lamp for a Lighthouse

Directory of Open Access Journals (Sweden)

Luca Mercatelli

2014-01-01

Full Text Available A novel sustainable source was developed for an existing Italian lighthouse, exploiting the light emitting diode (LED technology and the norms evolution. The research work started with the optical design of the device, while this work concerns the realization, installation, and test of the new LED lamp. The lamp recombines multiple separated LEDs, realizing a quasipunctual localized source. After installation in the lighthouse, specific photometric tests verified that the proposed power-saving source satisfied the illumination requirements of the marine signaling norms. The advantages of the LED-based lamp are reduced energy consumption, enhanced efficiency, longer life, decreased faults, slower aging, and lower maintenance costs. The obtained LED signalling device is more durable and reliable. In the future the application of these power-saving long-life sources could be extended to other maritime signaling devices or to other traffic signs.

The possible ocular hazards of LED dental illumination applications.

Science.gov (United States)

Stamatacos, Catherine; Harrison, Janet L

2013-01-01

The use of high-intensity illumination via Light-Emitting Diode (LED) headlamps is gaining in popularity with dentists and student dentists. Practitioners are using LED headlamps together with magnifying loupes, overhead LED illumination and fiber-optic dental handpieces for long periods of time. Although most manufacturers of these LED illuminators advertise that their devices emit "white" light, these still consist of two spectral bands--the blue spectral band, with its peak at 445 nm, and the green with its peak at 555 nm. While manufacturers suggest that their devices emit "white" light, spectral components of LED lights from different companies are significantly different. Dental headlamp manufacturers strive to create a white LED, and they advertise that this type of light emitted from their product offers bright white-light illumination. However, the manufacturing of a white LED light is done through selection of a white LED-type based on the peak blue strength in combination with the green peak strength and thus creating a beam-forming optic, which determines the beam quality. Some LED illuminators have a strong blue-light component versus the green-light component. Blue-light is highly energized and is close in the color spectrum to ultraviolet-light. The hazards of retinal damage with the use of high-intensity blue-lights has been well-documented. There is limited research regarding the possible ocular hazards of usage of high-intensity illuminating LED devices. Furthermore, the authors have found little research, standards, or guidelines examining the possible safety issues regarding the unique dental practice setting consisting of the combined use of LED illumination systems. Another unexamined component is the effect of high-intensity light reflective glare and magnification back to the practitioner's eyes due to the use of water during dental procedures. Based on the result of Dr. Janet Harrison's observations of beginning dental students in a

Development and future of ultraviolet light-emitting diodes: UV-LED will replace the UV lamp

International Nuclear Information System (INIS)

Muramoto, Yoshihiko; Kimura, Masahiro; Nouda, Suguru

2014-01-01

Ultraviolet light-emitting diodes (UV-LEDs) have started replacing UV lamps. The power per LED of high-power LED products has reached 12 W (14 A), which is 100 times the values observed ten years ago. In addition, the cost of these high-power LEDs has been decreasing. In this study, we attempt to understand the technologies and potential of UV-LEDs. (invited article)

The LED and fiber based calibration system for the photomultiplier array of SNO+

Science.gov (United States)

Seabra, L.; Alves, R.; Andringa, S.; Bradbury, S.; Carvalho, J.; Clark, K.; Coulter, I.; Descamps, F.; Falk, L.; Gurriana, L.; Kraus, C.; Lefeuvre, G.; Maio, A.; Maneira, J.; Mottram, M.; Peeters, S.; Rose, J.; Sinclair, J.; Skensved, P.; Waterfield, J.; White, R.; Wilson, J.; SNO+ Collaboration

2015-02-01

A new external LED/fiber light injection calibration system was designed for the calibration and monitoring of the photomultiplier array of the SNO+ experiment at SNOLAB. The goal of the calibration system is to allow an accurate and regular measurement of the photomultiplier array's performance, while minimizing the risk of radioactivity ingress. The choice in SNO+ was to use a set of optical fiber cables to convey into the detector the light pulses produced by external LEDs. The quality control was carried out using a modified test bench that was used in QC of optical fibers for TileCal/ATLAS. The optical fibers were characterized for transmission, timing and angular dispersions. This article describes the setups used for the characterization and quality control of the system based on LEDs and optical fibers and their results.

Temperature increase inside LED-based illuminators for in vitro aPDT photodamage studies

Science.gov (United States)

Battisti, A.; Morici, P.; Tortora, G.; Menciassi, A.; Checcucci, G.; Ghetti, F.; Sgarbossa, A.

2018-06-01

Antimicrobial PhotoDynamic Therapy (aPDT) is an emerging strategy aimed at the eradication of bacterial infections, with a special focus on antibiotic-resistant bacteria. This method is easy to apply, not expensive and particularly interesting in case of bacteria that spontaneously produce the required photosensitizers. In the framework of a project aimed at the development of an ingestible pill for the application of aPDT to gastric infections by Helicobacter pylori, a LED-based illuminating prototype (LED-BIP) was purposely designed in order to evaluate the photodamage induced by light of different wavelengths on porphyrin-producing bacteria. This short paper reports about temperature tests performed to assess the maximum exposure time and light dose that can be administered to bacterial cultures inside LED-BIP without reaching temperatures exceeding the physiological range.

Demonstration Assessment of Light-Emitting Diode (LED) Parking Lot Lighting at T.J.Maxx in Manchester, NH Phase I

Energy Technology Data Exchange (ETDEWEB)

Myer, Michael; Goettel, Russell T.

2010-06-29

A report describing the process and results of replacing existing parking lot lighting, looking at a LED option with occupancy sensors, and conventional alternates. Criteria include payback, light levels, occupant satisfaction. This report is Phase I of II. Phase I deals with initial installation.

Design of LED projector based on gradient-index lens

Science.gov (United States)

Qian, Liyong; Zhu, Xiangbing; Cui, Haitian; Wang, Yuanhang

2018-01-01

In this study, a new type of projector light path is designed to eliminate the deficits of existing projection systems, such as complex structure and low collection efficiency. Using a three-color LED array as the lighting source, by means of the special optical properties of a gradient-index lens, the complex structure of the traditional projector is simplified. Traditional components, such as the color wheel, relay lens, and mirror, become unnecessary. In this way, traditional problems, such as low utilization of light energy and loss of light energy, are solved. With the help of Zemax software, the projection lens is optimized. The optimized projection lens, LED, gradient-index lens, and digital micromirror device are imported into Tracepro. The ray tracing results show that both the utilization of light energy and the uniformity are improved significantly.

LEDs light spectrum effect on the success of fragmentation and growth of the leather coral Sarcophyton spp.

Directory of Open Access Journals (Sweden)

João Chambel

2014-06-01

Full Text Available The increasing demand for soft corals is reflected on the high attention of the scientific community during the last decades, with several studies focus on production techniques and optimization of coral husbandry (Schlacher et al., 2007;Sella and Benayahu, 2010. However, coral culture success is influenced by the interaction of different factors, such as water movement, temperature, nutrients, heterotrophic feeding and light conditions (Rocha et al., 2013a. Light plays a key role in the growth, reproduction and physiology of scleractinian corals that host phototrophic symbionts and it has been found that the photoresponse of corals is species-specific. Several studies have already focused on the effects of irradiance on coral and its algal symbionts (Osinga et al., 2011. Although, only a few works have investigated the role of the spectral quality of light on coral photobiology, physiology and growth (Rocha et al., 2013b. In the present study, we hypothesize that light spectrum can influence the growth performance of scleractinian corals when exposed at identical intensities of photosynthetically active radiation (PAR. To test our hypothesis we evaluated the effect of contrasting light spectra with an identical PAR of 70 ± 10 μmol quantam−2.s−1emitted by T8 fluorescent lamps (used as a control treatment and three different colours of Light Emitting Diode (LED, white, blue and red. It was evaluated survival and growth rates of Sarcophyton spp., an important scleractinian coral in the marine aquarium trade and for the bioprospecting of marine natural compounds. Replicated coral fragments were obtained from two mother colonies and were exposed to the four types of light spectrum for a period of 30 days. At the end of the experiment period, the results showed 100% of survival in coral fragments, and specific growth rate (SGR of 0,055 ± 0,09 %/day in control group and 0,091 ± 0,019 %/day, 0,210 ± 0,031 %/day and 0,380 ± 0,245 %/day in

Assembling and Using an LED-Based Detector to Monitor Absorbance Changes during Acid-Base Titrations

Science.gov (United States)

Santos, Willy G.; Cavalheiro, E´der T. G.

2015-01-01

A simple photometric assembly based in an LED as a light source and a photodiode as a detector is proposed in order to follow the absorbance changes as a function of the titrant volume added during the course of acid-base titrations in the presence of a suitable visual indicator. The simplicity and low cost of the electronic device allow the…

White LEDs as broad spectrum light sources for spectrophotometry: demonstration in the visible spectrum range in a diode-array spectrophotometric detector.

Science.gov (United States)

Piasecki, Tomasz; Breadmore, Michael C; Macka, Mirek

2010-11-01

Although traditional lamps, such as deuterium lamps, are suitable for bench-top instrumentation, their compatibility with the requirements of modern miniaturized instrumentation is limited. This study investigates the option of utilizing solid-state light source technology, namely white LEDs, as a broad band spectrum source for spectrophotometry. Several white light LEDs of both RGB and white phosphorus have been characterized in terms of their emission spectra and energy output and a white phosphorus Luxeon LED was then chosen for demonstration as a light source for visible-spectrum spectrophotometry conducted in CE. The Luxeon LED was fixed onto the base of a dismounted deuterium (D(2) ) lamp so that the light-emitting spot was geometrically positioned exactly where the light-emitting spot of the original D(2) lamp is placed. In this manner, the detector of a commercial CE instrument equipped with a DAD was not modified in any way. As the detector hardware and electronics remained the same, the change of the deuterium lamp for the Luxeon white LED allowed a direct comparison of their performances. Several anionic dyes as model analytes with absorption maxima between 450 and 600 nm were separated by CE in an electrolyte of 0.01 mol/L sodium tetraborate. The absorbance baseline noise as the key parameter was 5 × lower for the white LED lamp, showing clearly superior performance to the deuterium lamp in the available, i.e. visible part of the spectrum. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparative Evaluation of Shear Bond Strength and Debonding Characteristics using Conventional Halogen Light Curing Unit and LED Light Curing Unit: An in vitro Study

Directory of Open Access Journals (Sweden)

Amit Bhardwaj

2013-01-01

Conclusion: The result of this study showed promise for the orthodontic application of LED as light curing units and 20 seconds of exposure time is adequate for both LED and Halogen light, since increasing the curing time to 40 seconds showed no significant difference.

Color Degradation of Textiles with Natural Dyes and of Blue Scale Standards Exposed to White LED Lamps:Evaluation of White LED Lamps for Effectiveness as Museum Lighting

Science.gov (United States)

Ishii, Mie; Moriyama, Takayoshi; Toda, Masahiro; Kohmoto, Kohtaro; Saito, Masako

White light-emitting diodes (LED) are well suited for museum lighting because they emit neither UV nor IR radiation, which damage artifacts. The color degradation of natural dyes and blue scale standards (JIS L 0841) by white LED lamps are examined, and the performance of white LED lamps for museum lighting is evaluated. Blue scale standard grades 1-6 and silk fabrics dyed with 22 types of natural dyes classified as mid to highly responsive in a CIE technical report (CIE157:2004) were exposed to five types of white LED lamps using different luminescence methods and color temperatures. Color changes were measured at each 15000 lx·hr (500 lx at fabric surface × 300 hr) interval ten times. The accumulated exposure totaled 150000 lx·hr. The data on conventional white LED lamps and previously reported white fluorescent (W) and museum fluorescent (NU) lamps was evaluated. All the white LED lamps showed lower fading rates compared with a W lamp on a blue scale grade 1. The fading rate of natural dyes in total was the same between an NU lamp (3000 K) and a white LED lamp (2869 K). However, yellow natural dyes showed higher fading rates with the white LED lamp. This tendency is due to the high power characteristic of the LED lamp around 400-500 nm, which possibly contributes to the photo-fading action on the dyes. The most faded yellow dyes were Ukon (Curcuma longa L.) and Kihada (Phellodendron amurense Rupr.), and these are frequently used in historic artifacts such as kimono, wood-block prints, and scrolls. From a conservation point of view, we need to continue research on white LED lamps for use in museum lighting.

Optimization of colour quality of LED lighting with reference to memory colours

OpenAIRE

Smet, Kevin; Ryckaert, Wouter; Pointer, Michael R.; Deconinck, Geert; Hanselaer, Peter

2012-01-01

Simulated and real tri- and tetrachromatic light-emitting-diode (LED) clusters were optimized for luminous efficacy of radiation (LER) and the memory colour quality metric developed by the authors. The simulated clusters showed no significant differences in achievable colour quality and LER between the different cluster types investigated. The real clusters (composed of commercially available LEDs) showed substantial differences in achievable colour quality and LER between the different clus...

Examination of the LED Source in Traffic Lights and the Effect of Airborne Dirt on its Performance

Directory of Open Access Journals (Sweden)

Amela Softić

2017-05-01

Full Text Available The performed evaluation consisted of two phases: measurement of the illumination levels of (new LED system and carrying out the public opinion poll on the subjective visual performance of LED in traffic lights. The results of the measured levels of illumination show that deposition of dirt considerably affects its values. The survey results confirm an overall positive impression on LED performances in traffic lights.

Development of a method for the characterization and operation of UV-LED for water treatment.

Science.gov (United States)

Kheyrandish, Ataollah; Mohseni, Madjid; Taghipour, Fariborz

2017-10-01

Tremendous improvements in semiconductor technology have made ultraviolet light-emitting diodes (UV-LEDs) a viable alternative to conventional UV sources for water treatment. A robust and validated experimental protocol for studying the kinetics of microorganism inactivation is key to the further development of UV-LEDs for water treatment. This study proposes a protocol to operate UV-LEDs and control their output as a polychromatic radiation source. In order to systematically develop this protocol, the results of spectral power distribution, radiation profile, and radiant power measurements of a variety of UV-LEDs are presented. A wide range of UV-LEDs was selected for this study, covering various UVA, UVB, and UVC wavelengths, viewing angles from 3.5° to 135°, and a variety of output powers. The effects of operational conditions and measurement techniques were investigated on these UV-LEDs using a specially designed and fabricated setup. Operating conditions, such as the UV-LED electrical current and solder temperature, were found to significantly affect the power and peak wavelength output. The measurement techniques and equipment, including the detector size, detector distance from the UV-LED, and potential reflection from the environment, were shown to influence the results for many of the UV-LEDs. The results obtained from these studies were analyzed and applied to the development of a protocol for UV-LED characterization. This protocol is presented as a guideline that allows the operation and control of UV-LEDs in any structure, as well as accurately measuring the UV-LED output. Such information is essential for performing a reliable UV-LED assessment for the inactivation of microorganisms and for obtaining precise kinetic data. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phosphors for near UV-Emitting LED's for Efficacious Generation of White Light

Energy Technology Data Exchange (ETDEWEB)

McKittrick, Joanna [Univ. of California, San Diego, CA (United States)

2013-09-30

1) We studied phosphors for near-UV (nUV) LED application as an alternative to blue LEDs currently being used in SSL systems. We have shown that nUV light sources could be very efficient at high current and will have significantly less binning at both the chip and phosphor levels. We identified phosphor blends that could yield 4100K lamps with a CRI of approximately 80 and LPWnUV,opt equal to 179 for the best performing phosphor blend. Considering the fact that the lamps were not optimized for light coupling, the results are quite impressive. The main bottleneck is an optimum blue phosphor with a peak near 440 nm with a full width half maximum of about 25 nm and a quantum efficiency of >95%. Unfortunately, that may be a very difficult task when we want to excite a phosphor at ~400 nm with a very small margin for Stokes shift. Another way is to have all the phosphors in the blend having the excitation peak at 400 nm or slightly shorter wavelength. This could lead to a white light source with no body color and optimum efficacy due to no self-absorption effects by phosphors in the blend. This is even harder than finding an ideal blue phosphor, but not necessarily impossible. 2) With the phosphor blends identified, light sources using nUV LEDs at high current could be designed with comparable efficacy to those using blue LEDs. It will allow us to design light sources with multiple wattages using the same chips and phosphor blends simply by varying the input current. In the case of blue LEDs, this is not currently possible because varying the current will lower the efficacy at high current and alter the color point. With improvement of phosphor blends, control over CRI could improve. Less binning at the chip level and also at the phosphor blend level could reduce the cost of SSL light sources. 3) This study provided a deeper understanding of phosphor characteristics needed for LEDs in general and nUV LEDs in particular. Two students received Ph.D. degrees and three

Protocol for Determining Ultraviolet Light Emitting Diode (UV-LED) Fluence for Microbial Inactivation Studies.

Science.gov (United States)

Kheyrandish, Ataollah; Mohseni, Madjid; Taghipour, Fariborz

2018-06-15

Determining fluence is essential to derive the inactivation kinetics of microorganisms and to design ultraviolet (UV) reactors for water disinfection. UV light emitting diodes (UV-LEDs) are emerging UV sources with various advantages compared to conventional UV lamps. Unlike conventional mercury lamps, no standard method is available to determine the average fluence of the UV-LEDs, and conventional methods used to determine the fluence for UV mercury lamps are not applicable to UV-LEDs due to the relatively low power output, polychromatic wavelength, and specific radiation profile of UV-LEDs. In this study, a method was developed to determine the average fluence inside a water suspension in a UV-LED experimental setup. In this method, the average fluence was estimated by measuring the irradiance at a few points for a collimated and uniform radiation on a Petri dish surface. New correction parameters were defined and proposed, and several of the existing parameters for determining the fluence of the UV mercury lamp apparatus were revised to measure and quantify the collimation and uniformity of the radiation. To study the effect of polychromatic output and radiation profile of the UV-LEDs, two UV-LEDs with peak wavelengths of 262 and 275 nm and different radiation profiles were selected as the representatives of typical UV-LEDs applied to microbial inactivation. The proper setup configuration for microorganism inactivation studies was also determined based on the defined correction factors.

SiO2 Nanopillars on Microscale Roughened Surface of GaN-Based Light-Emitting Diodes by SILAR-Based Method

Directory of Open Access Journals (Sweden)

X. F. Zeng

2013-01-01

Full Text Available We reported the SiO2 nanopillars on microscale roughened surface on GaN-based LED to enhance light-extraction efficiency. ZnO nanoparticles were deposited on SiO2 as an etching mask before ICP etching SiO2 by successive ionic layer adsorption and reaction method (SILAR, and the different heights of SiO2 nanopillars on microroughened ITO/GaN were obtained after etching. Compared to a regular (flat surface GaN-based LED, the light output power for a LED with microroughening was increased by 33%. Furthermore, the proposed LEDs with SiO2 nanopillars on microroughened surface show the enhancement in light output power by 42.7%–49.1% at 20 mA. The increase in light output power is mostly attributed to reduction in Fresnel reflection by rough surface. The height of SiO2 nanopillars was increasing cause resulting in more rough on the microscale surface of GaN-based LEDs.

Design Secondary Optical System Applied in White-LED General Illumination

International Nuclear Information System (INIS)

Chen Chen; Zhang Xianhui

2011-01-01

As a new generation of light source, LED has many advantages that other light sources do not have. However, due to the nonuniform lighting of LED, secondary LED optical system design is particularly important. Freeform surface tailoring method, an important method of lighting design, establishes a light intensity change model after smooth surface refraction (reflection) of the light and simplifies the solution process for more complex issues of solution using the free surface tailoring method. Based on this method, secondary LED optical system is designed, and the light intensity distribution is simulated after LED light passes through the secondary optical system. The results show that the method has not only simplified the calculation process of the free surface tailoring method, but also the designed LED secondary optical system has achieved the purpose of uniform lighting to a certain degree.

Photobiomodulation versus light-emitting diode (LED) therapy in the treatment of temporomandibular disorder: study protocol for a randomized, controlled clinical trial.

Science.gov (United States)

Langella, Luciana G; Silva, Paula F C; Costa-Santos, Larissa; Gonçalves, Marcela L L; Motta, Lara J; Deana, Alessandro M; Fernandes, Kristianne P S; Mesquita-Ferrari, Raquel A; Bussadori, Sandra Kalil

2018-01-26

Temporomandibular disorder (TMD) is described as a subgroup of orofacial pain with a set of signs and symptoms that involve the temporomandibular joint, masticatory muscles, ears, and neck. TMD can occur unilaterally or bilaterally and approximately 70% of the population is affected with at least one sign. The disorder progresses with orofacial pain, muscle pain involving the masticatory and cervical muscles, joint noises (clicks and pops), joint block, mandibular dysfunction, and headache. The etiology can be abnormal occlusion and/or posture, trauma involving local tissues, repetitive microtrauma, parafunctional habits, and an increase in emotional stress. Studies have demonstrated that phototherapy is an efficient option for the treatment of TMD, leading to improvements in pain and orofacial function. The aim of the proposed study is to compare the effects of two sources of photobiomodulation in individuals with TMD. A randomized, controlled, double-blind, clinical trial is proposed, which will involve 80 individuals aged 18-65 years allocated to either a laser group or light-emitting diode (LED) group submitted to 12 sessions of phototherapy. The Research Diagnostic Criteria for TMDs will be used to evaluate all participants. Pain will be measured using the visual analog scale and maximum vertical mandibular movement will be determined with the aid of digital calipers. This study compares the effects of two modalities of laser therapy on the pain and orofacial function of patients with TMD dysfunction. Photobiomodulation and LED therapy are treatment options for reducing the inflammatory process and pain as well as inducing the regeneration of the target tissue. ClinicalTrials.gov, NCT03257748 . Registered on 8 August 2017.

Growth of monolithic full-color GaN-based LED with intermediate carrier blocking layers

Energy Technology Data Exchange (ETDEWEB)

El-Ghoroury, Hussein S.; Yeh, Milton; Chen, J. C., E-mail: jc.chen@ostendo.com; Li, X.; Chuang, Chih-Li [EPI Lab, Ostendo Technologies, Inc., 679 Brea Canyon Rd, Walnut, CA 91789 (United States)

2016-07-15

Specially designed intermediate carrier blocking layers (ICBLs) in multi-active regions of III-nitride LEDs were shown to be effective in controlling the carrier injection distribution across the active regions. In principle, the majority of carriers, both holes and electrons, can be guided into targeted quantum wells and recombine to generate light of specific wavelengths at controlled current-densities. Accordingly we proposed and demonstrated a novel monolithic InGaN-based LED to achieve three primary colors of light from one device at selected current densities. This LED structure, which has three different sets of quantum wells separated with ICBLs for three primary red-green-blue (RGB) colors, was grown by metal-organic chemical vapor deposition (MOCVD). Results show that this LED can emit light ranging from 460 to 650 nm to cover the entire visible spectrum. The emission wavelength starts at 650 nm and then decreases to 460 nm or lower as the injection current increases. In addition to three primary colors, many other colors can be obtained by color mixing techniques. To the best of our knowledge, this is the first demonstration of monolithic full-color LED grown by a simple growth technique without using re-growth process.

Growth of monolithic full-color GaN-based LED with intermediate carrier blocking layers

International Nuclear Information System (INIS)

El-Ghoroury, Hussein S.; Yeh, Milton; Chen, J. C.; Li, X.; Chuang, Chih-Li

2016-01-01

Specially designed intermediate carrier blocking layers (ICBLs) in multi-active regions of III-nitride LEDs were shown to be effective in controlling the carrier injection distribution across the active regions. In principle, the majority of carriers, both holes and electrons, can be guided into targeted quantum wells and recombine to generate light of specific wavelengths at controlled current-densities. Accordingly we proposed and demonstrated a novel monolithic InGaN-based LED to achieve three primary colors of light from one device at selected current densities. This LED structure, which has three different sets of quantum wells separated with ICBLs for three primary red-green-blue (RGB) colors, was grown by metal-organic chemical vapor deposition (MOCVD). Results show that this LED can emit light ranging from 460 to 650 nm to cover the entire visible spectrum. The emission wavelength starts at 650 nm and then decreases to 460 nm or lower as the injection current increases. In addition to three primary colors, many other colors can be obtained by color mixing techniques. To the best of our knowledge, this is the first demonstration of monolithic full-color LED grown by a simple growth technique without using re-growth process.

A new LED device used for photodynamic therapy in treatment of moderate to severe acne vulgaris.

Science.gov (United States)

Dong, Yiyun; Zhou, Guoyu; Chen, Jinan; Shen, Lingyue; Jianxin, Zhao; Xu, Qing; Zhu, Yulan

2016-03-01

This study investigated the efficacy and safety of a newly designed LED device used in photodiagnosis and photodynamic therapy of moderate to severe acne vulgaris in Chinese patients. Forty-six patients with moderate to severe facial acne showing high degrees of fluorescence by ultraviolet light examination were illuminated during ALA-PDT with two wavelengths of light (543-548 nm, and 630±6 nm, respectively) after 2 h of incubation with ALA. Each patient received treatment once every 30 days for two or three sessions. Two independent investigators assigned an acne severity score at baseline, one week after each treatment, as well as 4, 8, and 12 weeks after the completion of treatment. Adverse effects were recorded during and after each treatment. All patients rated their satisfaction with the results of treatment at a 12-week follow up visit. The ALA-PDL treatment regimen showed an overall effectiveness rate of 89.13% (41/46 patients). Some degree of clinical efficacy was seen in 71.42%, 86.67%, and 95.83% of patients with grades IV, V, and VI acne, respectively, and the rate of clinical effectiveness increased with increasing acne severity. When compared with baseline scores, significant reductions in acne scores were obtained at 8, and 12 weeks after completion of treatment. Maximum efficacy was shown at the 12 week follow up. No severe adverse events were observed. ALA-PDT administered with the newly designed LED device was an effective treatment for moderate to severe acne vulgaris, and side effects were mild and reversible. Copyright © 2015 Elsevier B.V. All rights reserved.

Red light emitting solid state hybrid quantum dot-near-UV GaN LED devices

International Nuclear Information System (INIS)

Song, Hongjoo; Lee, Seonghoon

2007-01-01

We produced core-shell (CdSe)ZnSe quantum dots by direct colloidal chemical synthesis and the surface-passivation method-an overcoating of the core CdSe with a larger-bandgap material ZnSe. The (CdSe)ZnSe quantum dots(QDs) play the role of a colour conversion centre. We call these quantum dots nanophosphors. We fabricated red light emitting hybrid devices of (CdSe)ZnSe QDs and a near-UV GaN LED by combining red light emitting (CdSe)ZnSe quantum dots (as a colour conversion centre) with a near-UV(NUV) GaN LED chip (as an excitation source). A few good red phosphors have been known for UV excitation wavelengths, and red phosphors for UV excitation have been sought for a long time. Here we tested the possibility of using (CdSe)ZnSe QDs as red nanophosphors for UV excitation. The fabricated red light emitting hybrid device of (CdSe)ZnSe and a NUV GaN LED chip showed a good luminance. We demonstrated that the (CdSe)ZnSe quantum dots were promising red nanophosphors for NUV excitation and that a red LED made of QDs and a NUV excitation source was a highly efficient hybrid device

340 nm pulsed UV LED system for europium-based time-resolved fluorescence detection of immunoassays

DEFF Research Database (Denmark)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter

2016-01-01

We report on the design, development and investigation of an optical system based on UV light emitting diode (LED) excitation at 340 nm for time-resolved fluorescence detection of immunoassays. The system was tested to measure cardiac marker Troponin I with a concentration of 200 ng....../L in immunoassay. The signal-to-noise ratio was comparable to state-of-the-art Xenon flash lamp based unit with equal excitation energy and without overdriving the LED. We performed a comparative study of the flash lamp and the LED based system and discussed temporal, spatial, and spectral features of the LED...... excitation for time-resolved fluorimetry. Optimization of the suggested key parameters of the LED promises significant increase of the signal-to-noise ratio and hence of the sensitivity of immunoassay systems....

340 nm pulsed UV LED system for europium-based time-resolved fluorescence detection of immunoassays.

Science.gov (United States)

Rodenko, Olga; Fodgaard, Henrik; Tidemand-Lichtenberg, Peter; Petersen, Paul Michael; Pedersen, Christian

2016-09-19

We report on the design, development and investigation of an optical system based on UV light emitting diode (LED) excitation at 340 nm for time-resolved fluorescence detection of immunoassays. The system was tested to measure cardiac marker Troponin I with a concentration of 200 ng/L in immunoassay. The signal-to-noise ratio was comparable to state-of-the-art Xenon flash lamp based unit with equal excitation energy and without overdriving the LED. We performed a comparative study of the flash lamp and the LED based system and discussed temporal, spatial, and spectral features of the LED excitation for time-resolved fluorimetry. Optimization of the suggested key parameters of the LED promises significant increase of the signal-to-noise ratio and hence of the sensitivity of immunoassay systems.

An engineering method to estimate the junction temperatures of light-emitting diodes in multiple LED application

International Nuclear Information System (INIS)

Fu, Xing; Hu, Run; Luo, Xiaobing

2014-01-01

Acquiring the junction temperature of light emitting diode (LED) is essential for performance evaluation. But it is hard to get in the multiple LED applications. In this paper, an engineering method is presented to estimate the junction temperatures of LEDs in multiple LED applications. This method is mainly based on an analytical model, and it can be easily applied with some simple measurements. Simulations and experiments were conducted to prove the feasibility of the method, and the deviations among the results obtained by the present method with those by simulation as well as experiments are less than 2% and 3%, respectively. In the final part of this study, the engineering method was used to analyze the thermal resistances of a street lamp. The material of lead frame was found to affect the system thermal resistance mostly, and the choice of solder material strongly depended on the material of the lead frame.

ICP dry etching ITO to improve the performance of GaN-based LEDs

International Nuclear Information System (INIS)

Meng Lili; Chen Yixin; Ma Li; Liu Zike; Shen Guangdi

2011-01-01

In order to improve the light efficiency of the conventional GaN-based light-emitting diodes (LEDs), the indium tin oxide (ITO) film is introduced as the current spreading layer and the light anti-reflecting layer on the p-GaN surface. There is a big problem with the ITO thin film's corrosion during the electrode preparation. In this paper, at least, the edge of the ITO film was lateral corroded 3.5 μm width, i.e. 6.43%-1/3 of ITO film's area. An optimized simple process, i.e. inductively couple plasma (ICP), was introduced to solve this problem. The ICP process not only prevented the ITO film from lateral corrosion, but also improved the LED's light intensity and device performance. The edge of the ITO film by ICP dry etching is steep, and the areas of ITO film are whole. Compared with the chip by wet etching, the areas of light emission increase by 6.43% at least and the chip's lop values increase by 45.9% at most. (semiconductor devices)

Hybrid GaN LED with capillary-bonded II–VI MQW color-converting membrane for visible light communications

International Nuclear Information System (INIS)

Santos, Joao M M; Jones, Brynmor E; Schlosser, Peter J; Herrnsdorf, Johannes; Guilhabert, Benoit; McKendry, Jonathan J D; Hastie, Jennifer E; Laurand, Nicolas; Dawson, Martin D; Watson, Scott; Kelly, Anthony E; De Jesus, Joel; Garcia, Thor A; Tamargo, Maria C

2015-01-01

The rapid emergence of gallium-nitride (GaN) light-emitting diodes (LEDs) for solid-state lighting has created a timely opportunity for optical communications using visible light. One important challenge to address this opportunity is to extend the wavelength coverage of GaN LEDs without compromising their modulation properties. Here, a hybrid source for emission at 540 nm consisting of a 450 nm GaN micro-sized LED (micro-LED) with a micron-thick ZnCdSe/ZnCdMgSe multi-quantum-well color-converting membrane is reported. The membrane is liquid-capillary-bonded directly onto the sapphire window of the micro-LED for full hybridization. At an injection current of 100 mA, the color-converted power was found to be 37 μW. At this same current, the −3 dB optical modulation bandwidth of the bare GaN and hybrid micro-LEDs were 79 and 51 MHz, respectively. The intrinsic bandwidth of the color-converting membrane was found to be power-density independent over the range of the micro-LED operation at 145 MHz, which corresponds to a mean carrier lifetime of 1.9 ns. (paper)

GaN-based micro-LED arrays on flexible substrates for optical cochlear implants

International Nuclear Information System (INIS)

Goßler, Christian; Bierbrauer, Colin; Moser, Rüdiger; Kunzer, Michael; Holc, Katarzyna; Pletschen, Wilfried; Köhler, Klaus; Wagner, Joachim; Schwarz, Ulrich T; Schwaerzle, Michael; Ruther, Patrick; Paul, Oliver; Neef, Jakob; Keppeler, Daniel; Hoch, Gerhard; Moser, Tobias

2014-01-01

Currently available cochlear implants are based on electrical stimulation of the spiral ganglion neurons. Optical stimulation with arrays of micro-sized light-emitting diodes (µLEDs) promises to increase the number of distinguishable frequencies. Here, the development of a flexible GaN-based micro-LED array as an optical cochlear implant is reported for application in a mouse model. The fabrication of 15 µm thin and highly flexible devices is enabled by a laser-based layer transfer process of the GaN-LEDs from sapphire to a polyimide-on-silicon carrier wafer. The fabricated 50 × 50 µm 2 LEDs are contacted via conducting paths on both p- and n-sides of the LEDs. Up to three separate channels could be addressed. The probes, composed of a linear array of the said µLEDs bonded to the flexible polyimide substrate, are peeled off the carrier wafer and attached to flexible printed circuit boards. Probes with four µLEDs and a width of 230 µm are successfully implanted in the mouse cochlea both in vitro and in vivo. The LEDs emit 60 µW at 1 mA after peel-off, corresponding to a radiant emittance of 6 mW mm −2 . (paper)

LED Technology for Dental Applications

DEFF Research Database (Denmark)

Argyraki, Aikaterini; Ou, Yiyu; Soerensen, L. H.

LEDs have a large potential in many dental and oral applications. Areas such as photo polymerization, fluorescence imaging, photodynamic therapy, and photoactivated disinfection are important future candidates for LED based diagnostics and treatment in dentistry.......LEDs have a large potential in many dental and oral applications. Areas such as photo polymerization, fluorescence imaging, photodynamic therapy, and photoactivated disinfection are important future candidates for LED based diagnostics and treatment in dentistry....

Quantifying the radiant exposure and effective dose in patients treated for actinic keratoses with topical photodynamic therapy using daylight and LED white light

Science.gov (United States)

Manley, M.; Collins, P.; Gray, L.; O'Gorman, S.; McCavana, J.

2018-02-01

Daylight photodynamic therapy (dl-PDT) is as effective as conventional PDT (c-PDT) for treating actinic keratoses but has the advantage of reducing patient discomfort significantly. Topical dl-PDT and white light-PDT (wl-PDT) differ from c-PDT by way of light sources and methodology. We measured the variables associated with light dose delivery to skin surface and influence of geometry using a radiometer, a spectral radiometer and an illuminance meter. The associated errors of the measurement methods were assessed. The spectral and spatial distribution of the radiant energy from the LED white light source was evaluated in order to define the maximum treatment area, setup and treatment protocol for wl-PDT. We compared the data with two red LED light sources we use for c-PDT. The calculated effective light dose is the product of the normalised absorption spectrum of the photosensitizer, protoporphyrin IX (PpIX), the irradiance spectrum and the treatment time. The effective light dose from daylight ranged from 3  ±  0.4 to 44  ±  6 J cm-2due to varying weather conditions. The effective light dose for wl-PDT was reproducible for treatments but it varied across the treatment area between 4  ±  0.1 J cm-2 at the edge and 9  ±  0.1 J cm-2 centrally. The effective light dose for the red waveband (615-645 nm) was 0.42  ±  0.05 J cm-2 on a clear day, 0.05  ±  0.01 J cm-2 on an overcast day and 0.9  ±  0.01 J cm-2 using the white light. This compares with 0.95  ±  0.01 and 0.84  ±  0.01 J cm-2 for c-PDT devices. Estimated errors associated with indirect determination of daylight effective light dose were very significant, particularly for effective light doses less than 5 J cm-2 (up to 83% for irradiance calculations). The primary source of error is in establishment of the relationship between irradiance or illuminance and effective dose. Use of the O’Mahoney model is recommended using a

Light-Emitting Diode-Based Illumination System for In Vitro Photodynamic Therapy

OpenAIRE

Defu Chen; Huifen Zheng; Zhiyong Huang; Huiyun Lin; Zhidong Ke; Shusen Xie; Buhong Li

2012-01-01

The aim of this study is to develop a light-emitting diode- (LED-) based illumination system that can be used as an alternative light source for in vitro photodynamic therapy (PDT). This illumination system includes a red LED array composed of 70 LEDs centered at 643 nm, an air-cooling unit, and a specific-designed case. The irradiance as a function of the irradiation distance between the LED array and the sample, the homogeneity and stability of irradiation, and the effect of long-time irrad...

Report on the investigational study on the technical trend of temperature control materials for high efficiency LED lighting use; Kokoritsu LED shomeiyo no ondo seigyo zairyo no gijutsu doko ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of the innovative conservation of lighting use energy, a project is being promoted with the aim of developing light emitted diode (LED) and commercializing lighting use light source substituting for fluorescent light. In this study, the following were conducted: literature survey on Peltier materials as temperature control materials for high efficiency LED lighting and the making of them as elements, extraction of technical subjects in the commercialization of LED cooling use Peltier element materials, market surveys/analyses were made of the fields of application including the LED cooling use field. As a result, for the commercialization of temperature control use Peltier elements of lighting use LED, the desirable performance index is 5x10{sup -5}/K or more. Bi{sub 2}Te{sub 3} elements which are now commercially available as Peltier elements are not good in performance and have the toxicity problem. As a candidate of temperature control use materials of lighting use LED, Mg{sub 2} (Sn, Si) or clathrate system are regarded, but the point, etc. were pointed out that it is necessary to improve thermoelectric characteristics. (NEDO)

The effect of LED illumination on endodontic biofilms

DEFF Research Database (Denmark)

Markvart, Merete

Within endodontics photodynamic therapy (PDT) has been suggested as a disinfectant procedure during root canal treatment. A photoactive dye (photosensitizer), methylene blue or toluidine blue, are activated by a light source, usually lasers or light emitting diodes (LEDs), thereby forming free...

Multispectral digital lensless holographic microscopy: from femtosecond laser to white light LED

International Nuclear Information System (INIS)

Garcia-Sucerquia, J

2015-01-01

The use of femtosecond laser radiation and super bright white LED in digital lensless holographic microscopy is presented. For the ultrafast laser radiation two different configurations of operation of the microscope are presented and the dissimilar performance of each one analyzed. The microscope operating with a super bright white light LED in combination with optical filters shows very competitive performance as it is compared with more expensive optical sources. The broadband emission of both radiation sources allows the multispectral imaging of biological samples to obtain spectral responses and/or full color images of the microscopic specimens; sections of the head of a Drosophila melanogaster fly are imaged in this contribution. The simple, solid, compact, lightweight, and reliable architecture of digital lensless holographic microscopy operating with broadband light sources to image biological specimens exhibiting micrometer-sized details is evaluated in the present contribution. (paper)

Tapering-induced enhancement of light extraction efficiency of nanowire deep ultraviolet LED by theoretical simulations

KAUST Repository

Lin, Ronghui

2018-04-21

A nanowire (NW) structure provides an alternative scheme for deep ultraviolet light emitting diodes (DUV-LEDs) that promises high material quality and better light extraction efficiency (LEE). In this report, we investigate the influence of the tapering angle of closely packed AlGaN NWs, which is found to exist naturally in molecular beam epitaxy (MBE) grown NW structures, on the LEE of NW DUV-LEDs. It is observed that, by having a small tapering angle, the vertical extraction is greatly enhanced for both transverse magnetic (TM) and transverse electric (TE) polarizations. Most notably, the vertical extraction of TM emission increased from 4.8% to 24.3%, which makes the LEE reasonably large to achieve high-performance DUV-LEDs. This is because the breaking of symmetry in the vertical direction changes the propagation of the light significantly to allow more coupling into radiation modes. Finally, we introduce errors to the NW positions to show the advantages of the tapered NW structures can be projected to random closely packed NW arrays. The results obtained in this paper can provide guidelines for designing efficient NW DUV-LEDs.

Tapering-induced enhancement of light extraction efficiency of nanowire deep ultraviolet LED by theoretical simulations

KAUST Repository

Lin, Ronghui; Galan, Sergio Valdes; Sun, Haiding; Hu, Yangrui; Alias, Mohd Sharizal; Janjua, Bilal; Ng, Tien Khee; Ooi, Boon S.; Li, Xiaohang

2018-01-01

A nanowire (NW) structure provides an alternative scheme for deep ultraviolet light emitting diodes (DUV-LEDs) that promises high material quality and better light extraction efficiency (LEE). In this report, we investigate the influence of the tapering angle of closely packed AlGaN NWs, which is found to exist naturally in molecular beam epitaxy (MBE) grown NW structures, on the LEE of NW DUV-LEDs. It is observed that, by having a small tapering angle, the vertical extraction is greatly enhanced for both transverse magnetic (TM) and transverse electric (TE) polarizations. Most notably, the vertical extraction of TM emission increased from 4.8% to 24.3%, which makes the LEE reasonably large to achieve high-performance DUV-LEDs. This is because the breaking of symmetry in the vertical direction changes the propagation of the light significantly to allow more coupling into radiation modes. Finally, we introduce errors to the NW positions to show the advantages of the tapered NW structures can be projected to random closely packed NW arrays. The results obtained in this paper can provide guidelines for designing efficient NW DUV-LEDs.

Comparative clinical study using laser and LED-therapy for orofacial pain relief: dentin hypersensitivity and cervicogenic headache

Science.gov (United States)

Lizarelli, Rosane F. Z.; Pizzo, Renata C. A.; Florez, Fernando L. E.; Grecco, Clovis; Speciali, Jose G.; Bagnato, Vanderlei S.

2015-06-01

Considering several clinical situations, low intensity laser therapy has been widely applied in pain relief or analgesia mechanism. With the advent of new LED-based (light emitting diode) light sources, the need of further clinical experiments aiming to compare the effectiveness among them is paramount. The LED system therapeutic use can be denominated as LEDT - Light Emitting Diode Therapy. This study proposed two clinical evaluations of pain relief effect: to dentin hypersensitivity and to cervicogenic headache using different sources of lasers (low and high intensity) and light emitting diodes (LEDs), one emitting at the spectral band of red (630+/- 5nm) and the other one at infrared band (880+/- 5nm). Two different clinical studies were performed and presented interesting results. Considering dentin hypersensitivity, red and infrared led were so effective than the control group (high intensity laser system); by the other side, considering cervicogenic headache, control group (infrared laser) was the best treatment in comparison to red and infrared led system.

Advances in LEDs for automotive applications

Science.gov (United States)

Bhardwaj, Jy; Peddada, Rao; Spinger, Benno

2016-03-01

High power LEDs were introduced in automotive headlights in 2006-2007, for example as full LED headlights in the Audi R8 or low beam in Lexus. Since then, LED headlighting has become established in premium and volume automotive segments and beginning to enable new compact form factors such as distributed low beam and new functions such as adaptive driving beam. New generations of highly versatile high power LEDs are emerging to meet these application needs. In this paper, we will detail ongoing advances in LED technology that enable revolutionary styling, performance and adaptive control in automotive headlights. As the standards which govern the necessary lumens on the road are well established, increasing luminance enables not only more design freedom but also headlight cost reduction with space and weight saving through more compact optics. Adaptive headlighting is based on LED pixelation and requires high contrast, high luminance, smaller LEDs with high-packing density for pixelated Matrix Lighting sources. Matrix applications require an extremely tight tolerance on not only the X, Y placement accuracy, but also on the Z height of the LEDs given the precision optics used to image the LEDs onto the road. A new generation of chip scale packaged (CSP) LEDs based on Wafer Level Packaging (WLP) have been developed to meet these needs, offering a form factor less than 20% increase over the LED emitter surface footprint. These miniature LEDs are surface mount devices compatible with automated tools for L2 board direct attach (without the need for an interposer or L1 substrate), meeting the high position accuracy as well as the optical and thermal performance. To illustrate the versatility of the CSP LEDs, we will show the results of, firstly, a reflector-based distributed low beam using multiple individual cavities each with only 20mm height and secondly 3x4 to 3x28 Matrix arrays for adaptive full beam. Also a few key trends in rear lighting and impact on LED light

LED photochemotherapy against Staphylococcus aureus: an in vitro study

Science.gov (United States)

de Oliveira, Susana C. P. S.; Monteiro, Juliana S. C.; Pires-Santos, Gustavo M.; Sampaio, Fernando José Pires; Soares, Luiz Guilherme P.; Soares, Amanda P.; Pinheiro, Antônio L. B.

2018-02-01

Bacterial resistance to antibiotics is reality and need for alternative treatments is urgent. The aim of this work was to evaluate, in vitro, the effect of LED photochemotherapy on Staphylococcus aureus (ATCC 23529) using 25 μg / mL of phenothiazine compound combined with LED light (λ632 +/- 2ηm) using 12 J/cm2 energy density. The experiments were carried out in triplicate and the samples were divided into groups: Control, Irradiated (treated only with light), Photosensitizer (treated only in the presence of the dye), LED-Photochemotherapy (treatment with light associated with dye). Counts of the colony forming units and the data obtained were statistically analyzed (ANOVA, Tukey's test, p<0.05). The present study demonstrated that the efficacy of LED-Photochemotherapy as the use of 25 μg/mL x 12 J/cm2 caused 91.57 % of inhibition of bacterial growth. It is concluded that using energy density of 12 J/cm2 associated to 25 μg/mL caused high in vitro inhibition of S. aureus.

On the application of CaF2:Eu and SrF2:Eu phosphors in LED based phototherapy lamp

Science.gov (United States)

Belsare, P. D.; Moharil, S. V.; Joshi, C. P.; Omanwar, S. K.

2013-06-01

In the last few years the interest of scientific community has been increased towards solid state lighting based on LEDs because of their superior advantages over the conventional fluorescent lamps. As the GaN based LEDs are easily available efforts of the researchers are now on making the new phosphors which are excitable in the near UV region (360-400nm) for solid state lighting. This paper reports the photoluminescence characteristics of CaF2:Eu and SrF2:Eu phosphor prepared by wet chemical method. The violet emission of these phosphors with near UV excitation can be useful in making a phototherapy lamp based on LEDs for treating various skin diseases like acne vulgaris and hyperbilirubinemia.

Intelligent Luminance Control of Lighting Systems Based on Imaging Sensor Feedback

Directory of Open Access Journals (Sweden)

Haoting Liu

2017-02-01

Full Text Available An imaging sensor-based intelligent Light Emitting Diode (LED lighting system for desk use is proposed. In contrast to the traditional intelligent lighting system, such as the photosensitive resistance sensor-based or the infrared sensor-based system, the imaging sensor can realize a finer perception of the environmental light; thus it can guide a more precise lighting control. Before this system works, first lots of typical imaging lighting data of the desk application are accumulated. Second, a series of subjective and objective Lighting Effect Evaluation Metrics (LEEMs are defined and assessed for these datasets above. Then the cluster benchmarks of these objective LEEMs can be obtained. Third, both a single LEEM-based control and a multiple LEEMs-based control are developed to realize a kind of optimal luminance tuning. When this system works, first it captures the lighting image using a wearable camera. Then it computes the objective LEEMs of the captured image and compares them with the cluster benchmarks of the objective LEEMs. Finally, the single LEEM-based or the multiple LEEMs-based control can be implemented to get a kind of optimal lighting effect. Many experiment results have shown the proposed system can tune the LED lamp automatically according to environment luminance changes.