WorldWideScience

Sample records for lean burn capability

  1. Hydrogen Addition for Improved Lean Burn Capability on Natural Gas Engine

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Tobias [Lund Inst. of Technology (Sweden). Dept. of Heat and Power Engineering

    2002-12-01

    Lean burn spark ignition (SI) engines powered by natural gas is an attractive alternative to the Diesel engine, especially in urban traffic, where reduction of tailpipe emissions are of great importance. A major benefit is the large reduction in soot (PM). Lean burn spark ignition (SI) engines yield high fuel conversion efficiency and also relatively low NO{sub x} emissions at full load. In order to improve the engine operating characteristics at lower loads, the {lambda}-value is normally reduced to some degree, with increased NO{sub x} emissions and reduced efficiency as a result. This is a drawback for the lean burn engines, especially in urban applications such as in city buses and distribution trucks for urban use. So, it is desirable to find ways to extend the lean limit at low loads. One way to improve these part load properties is to add hydrogen to the natural gas in order to improve the combustion characteristics of the fuel. It is possible to extend the lean limit of a natural gas engine by addition of hydrogen to the primary fuel. This report presents measurements made on a single cylinder 1.6 liter natural gas engine. Two combustion chambers, one slow and one fast burning, were tested with various amounts of hydrogen (0 to 20 %-vol) added to natural gas. Three operating conditions were investigated for each combustion chamber and each hydrogen content level; idle, wide open throttle (WOT) and a high load condition (simulated turbo charging). For all three operating conditions, the air/fuel ratio was varied between stoichiometric and the lean limit. For each operating point, the ignition timing was swept in order to find maximum brake torque (MBT) timing. In some cases were the ignition timing limited by knock. Heat release rate calculations were made in order to assess the influence of hydrogen addition on burn rate. Addition of hydrogen showed an increase in burn rate for both combustion chambers, resulting in more stable combustion close to the lean

  2. Lean-burn engines UHC emission reduction

    Energy Technology Data Exchange (ETDEWEB)

    Karll, B.; Kristensen, P.G.; Nielsen, M.; Iskov, H. [Danish Gas Technology Centre a/s (Denmark); Broe Bendtsen, A.; Glarborg, P.; Dam-Johansen, K. [Technical University of Denmark. CHEC, Department of Chemical Engineering (Denmark)

    1999-04-01

    at increased NO{sub x} levels and the results show that increased NO{sub x} levels improve the UHC conversion in the exhaust reactor. The process is found to be very dependent on actual NO{sub x} levels and the exhaust reactor temperature. The exhaust temperature from lean burn engines is in the range from 450 to 550 deg. C depending on the engine settings and type. The conclusion from the tests shows that only if the temperature in the exhaust system is raised, it will be possible to use the NO{sub x} enhanced UHC oxidation process for post oxidation. Injection of hydrogen peroxide caused a significant reduction in the stack emission of UHC by conversion of UHC at conditions where the exhaust reactor otherwise was unable to oxidise UHC. The stack emission of UHC was reduced by 40-60% during test engine conditions. (EHS) EFP-96; 14 refs.

  3. Lean-burn engines UHC emission reduction

    International Nuclear Information System (INIS)

    Karll, B.; Kristensen, P.G.; Nielsen, M.; Iskov, H.; Broe Bendtsen, A.; Glarborg, P.; Dam-Johansen, K.

    1999-01-01

    the results show that increased NO x levels improve the UHC conversion in the exhaust reactor. The process is found to be very dependent on actual NO x levels and the exhaust reactor temperature. The exhaust temperature from lean burn engines is in the range from 450 to 550 deg. C depending on the engine settings and type. The conclusion from the tests shows that only if the temperature in the exhaust system is raised, it will be possible to use the NO x enhanced UHC oxidation process for post oxidation. Injection of hydrogen peroxide caused a significant reduction in the stack emission of UHC by conversion of UHC at conditions where the exhaust reactor otherwise was unable to oxidise UHC. The stack emission of UHC was reduced by 40-60% during test engine conditions. (EHS) EFP-96; 14 refs

  4. NOx storage and reduction over a lean-burn automotive catalyst

    NARCIS (Netherlands)

    Scholz, C.M.L.

    2007-01-01

    Nowadays, there is an increased interest in lean-burn technologies, i.e. diesel and lean-burn gasoline engines, mainly due to their higher fuel efficiency compared to conventional gasoline engines. Lean-burn engines work under excess oxygen and consequently produce oxygen-rich exhaust. This

  5. Lean process management implementation through enhanced problem solving capabilities

    Directory of Open Access Journals (Sweden)

    Perumal Puvanasvaran

    2010-12-01

    Full Text Available All Original Equipment Manufacturers (OEM organizations in Aerospace, Automotive and Electronics industries had to upgrade their functions. These organizations including suppliers and solutions providers are duty bound to improve their functions through strategic initiatives. One such initiative is Lean Process Management. Lean Process Management has proven to aid organizations in developing manufacturing and administrative management solutions and make the organization a leaner at the same time a ‘fitter’ one, achieving World Class standards in terms of production, quality, marketing, etc, etc. The issue or problem is, although a number of authors, experts, researchers have discussed the lean process management as part organization centric issues, they failed to provide an effective lean process management system. Besides the need to formulate an effective lean process as suggested by some authors, another important reason suggested is the employee’s development aspect regarding how to unlock the infinite potential of their workforce. This employee’s development is basically the problem solving capabilities of the employees while implementing the Lean through clear cutting protocols or processes of Lean Process Management. The employees need to be developed and equipped to contribute optimally to the process. Because of this scenario, the main objective of this study is to develop an employees development system which the author has acronym or trademark it as People Development System (PDS to enhance problem solving capability among its employees while implementing the lean process management there. Although, the PDS can be implemented throughout the organization, if it is implemented in a particular department in an organization, it will be feasible to study and analyze its effectiveness in-depth. So, this study documents and analyzes the implementation of Lean process in the Kitting Department of the aerospace company, ABC Company

  6. Urban air quality improvement by using a CNG lean burn engine for city buses

    NARCIS (Netherlands)

    Merétei, T.; Ling, J.A.N. van; Havenith, C.

    1998-01-01

    The use of compressed natural gas (CNG)-fuelled lean-burn city bus engines has a significant potential for air quality improvement in urban areas. Particularly important is the reduction of NO, as well as particulate and non regulated HC-emissions. For this reason, a CNG-fuelled, lean-burn,

  7. Rich-burn, flame-assisted fuel cell, quick-mix, lean-burn (RFQL) combustor and power generation

    Science.gov (United States)

    Milcarek, Ryan J.; Ahn, Jeongmin

    2018-03-01

    Micro-tubular flame-assisted fuel cells (mT-FFC) were recently proposed as a modified version of the direct flame fuel cell (DFFC) operating in a dual chamber configuration. In this work, a rich-burn, quick-mix, lean-burn (RQL) combustor is combined with a micro-tubular solid oxide fuel cell (mT-SOFC) stack to create a rich-burn, flame-assisted fuel cell, quick-mix, lean-burn (RFQL) combustor and power generation system. The system is tested for rapid startup and achieves peak power densities after only 35 min of testing. The mT-FFC power density and voltage are affected by changes in the fuel-lean and fuel-rich combustion equivalence ratio. Optimal mT-FFC performance favors high fuel-rich equivalence ratios and a fuel-lean combustion equivalence ratio around 0.80. The electrical efficiency increases by 150% by using an intermediate temperature cathode material and improving the insulation. The RFQL combustor and power generation system achieves rapid startup, a simplified balance of plant and may have applications for reduced NOx formation and combined heat and power.

  8. Lean-burn stratified combustion at gasoline engines; Magere Schichtverbrennung beim Ottomotor

    Energy Technology Data Exchange (ETDEWEB)

    Breitbach, Hermann [Daimler AG, Stuttgart (Germany). Entwicklung Einspritzung und Betriebsstoffe; Waltner, Anton [Daimler AG, Stuttgart (Germany). Verbrennungsentwicklung Pkw-Ottomotoren; Landenfeld, Tilo [Robert Bosch GmbH, Schwieberdingen (Germany). Hochdruckeinspritzung Piezo; Porten, Guido [Robert Bosch GmbH, Schwieberdingen (Germany). Systementwicklung Benzindirekteinspritzung

    2013-05-01

    Spray-guided lean-burn combustion is an integral part of the Mercedes-Benz technology strategy for highly efficient and clean gasoline engines. With regard to the excellent fuel efficiency combined with outstanding specific power, a good combustion system robustness and the low particulate emissions, the concept offers a very good cost/benefit ratio especially for the Euro 6 emission legislation. Thus, Mercedes-Benz believes, that the sprayguided lean-burn combustion offers the by far highest future viability of gasoline engine combustion systems.

  9. Reduce NOx Emissions by Adsorber-Reduction Catalyst on Lean Burn Gasoline Engine

    Directory of Open Access Journals (Sweden)

    Dongpeng Yue

    2013-09-01

    Full Text Available The effect of a new catalyst system composed of traditional three way catalyst converter and adsorber-reduction catalysis converter on the emission characteristics and BSFC (Breake Specific Fuel Consumption- BSFCof a lean burn gasoline engine operated were investigated in this paper under different schemes of catalyst converter arrangement and different speeds and loads. The results show that the position of Three Way Catalyst is before the NOx adsorber Catalyst was the best scheme of catalyst converter arrangement. Which has the highest converter efficiency of reduction NOx emission in lean burn gasoline engine. The effects of speed on the exhaust emission and BSFC were also related to the ratio of lean burn time to rich burn time and the absolute value of both time of the adsorber-reduction catalyst converter. The load of the engine was the main influential factor to the exhaust emission characteristics and BSFC of lean burn gasoline engine, and the more load of the engine was, the more NOx emission , the less NOx conversion rate (CNOx and the better BSFC were.

  10. Stoichiometric and lean burn heavy-duty gas engines: a dilemma between emissions and fuel consumption?

    NARCIS (Netherlands)

    Steen, M. van der; Rijke, J. de; Seppen, J.J.

    1996-01-01

    This paper compares stoichiometric with lean burn technology for heavy-duty gas engines (natural gas and LPG) and demonstrates that there is a future for both engine concepts on the multilateral global market. Emission limits in Europe as expected in the near future will facilitate both engine

  11. Multi-Stage Selective Catalytic Reduction of NOx in Lean-Burn Engine Exhaust

    National Research Council Canada - National Science Library

    Penetrante, B

    1997-01-01

    .... A plasma can also be used to oxidize NO to NO2. This paper compares the multi-stage catalytic scheme with the plasma-assisted catalytic scheme for reduction of NOx in lean-burn engine exhausts. The advantages of plasma oxidation over catalytic oxidation are presented.

  12. A model based lean approach to capability management

    CSIR Research Space (South Africa)

    Venter, Jacobus P

    2017-09-01

    Full Text Available It is argued that the definition of the required operational capabilities in the short and long term is an essential element of command. Defence Capability Management can be a cumbersome, long and very resource intensive activity. Given the new...

  13. Burning low volatile fuel in tangentially fired furnaces with fuel rich/lean burners

    International Nuclear Information System (INIS)

    Wei Xiaolin; Xu Tongmo; Hui Shien

    2004-01-01

    Pulverized coal combustion in tangentially fired furnaces with fuel rich/lean burners was investigated for three low volatile coals. The burners were operated under the conditions with varied value N d , which means the ratio of coal concentration of the fuel rich stream to that of the fuel lean stream. The wall temperature distributions in various positions were measured and analyzed. The carbon content in the char and NO x emission were detected under various conditions. The new burners with fuel rich/lean streams were utilized in a thermal power station to burn low volatile coal. The results show that the N d value has significant influences on the distributions of temperature and char burnout. There exists an optimal N d value under which the carbon content in the char and the NO x emission is relatively low. The coal ignition and NO x emission in the utilized power station are improved after retrofitting the burners

  14. Vortex combustor for low NOX emissions when burning lean premixed high hydrogen content fuel

    Science.gov (United States)

    Steele, Robert C; Edmonds, Ryan G; Williams, Joseph T; Baldwin, Stephen P

    2012-11-20

    A trapped vortex combustor. The trapped vortex combustor is configured for receiving a lean premixed gaseous fuel and oxidant stream, where the fuel includes hydrogen gas. The trapped vortex combustor is configured to receive the lean premixed fuel and oxidant stream at a velocity which significantly exceeds combustion flame speed in a selected lean premixed fuel and oxidant mixture. The combustor is configured to operate at relatively high bulk fluid velocities while maintaining stable combustion, and low NOx emissions. The combustor is useful in gas turbines in a process of burning synfuels, as it offers the opportunity to avoid use of diluent gas to reduce combustion temperatures. The combustor also offers the possibility of avoiding the use of selected catalytic reaction units for removal of oxides of nitrogen from combustion gases exiting a gas turbine.

  15. NO adsorption behaviors of the MnO{sub x} catalysts in lean-burn atmospheres

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Li [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Applied Catalysis Science and Technology, Tianjin 300072 (China); The Co-innovation Center of Chemistry and Chemical Engineering of Tianjin, Tianjin 300072 (China); Xian, Hui [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Pei-Yang Distillation Engineering Limited Company, Tianjin 300072 (China); Li, Qi-Feng; Chen, Da [Tianjin Key Laboratory of Biomedical Detecting Techniques and Instruments, School of Precision Instruments and Opto-electronics Engineering, Tianjin University, Tianjin 300072 (China); Tan, Yi-Sheng [State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Science, Taiyuan 030001 (China); Zhang, Jing; Zheng, Li-Rong [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Li, Xin-Gang, E-mail: xingang_li@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Applied Catalysis Science and Technology, Tianjin 300072 (China); The Co-innovation Center of Chemistry and Chemical Engineering of Tianjin, Tianjin 300072 (China)

    2013-09-15

    Highlights: • α-Mn{sub 2}O{sub 3} is a promising NO{sub x} adsorber for lean-burn exhausts even at low temperatures. • NO{sub x} was weakly bonded on α-Mn{sub 2}O{sub 3}, but strongly bonded on β-MnO{sub 2}. • NO could efficiently adsorb/desorb within the lean/rich cyclings over α-Mn{sub 2}O{sub 3}. • The superficial oxygen species plays a key role for the NO oxidation over α-Mn{sub 2}O{sub 3}. • The NO adsorption and oxidation follow the L–H and/or E–R mechanism over α-Mn{sub 2}O{sub 3}. -- Abstract: NO{sub x} emission control of lean-burn engines is one of the great challenges in the world. Herein, the MnO{sub x} model catalysts with the different calcination temperatures were synthesized to investigate their NO adsorbability for lean-burn exhausts. The transformation from (β-)MnO{sub 2} to (α-)Mn{sub 2}O{sub 3} following the increased calcination temperatures was evidenced from the viewpoint of the local atomic level. Among these samples, the one calcined at 550 °C containing the single α-Mn{sub 2}O{sub 3} phase displayed the best NO adsorbability: NO was mainly adsorbed in the forms of NO/nitrites and NO{sub 2}/nitrates at the low and high temperatures, respectively; the NO oxidation ability displayed the volcano-shape following the increased operating temperatures, and reached the maximum, i.e. 92.4% of the NO-to-NO{sub 2} conversion, at 250 °C. Moreover, this sample presented the efficiently reversible NO adsorption/desorption performance in alternative lean-burn/fuel-rich atmospheres, due to the weakly bonded NO{sub x} on it. The superficial oxygen species plays a critical role for the NO oxidation over α-Mn{sub 2}O{sub 3}. The consumed superficial oxygen could be further compensated by the gaseous and lattice oxygen therein. Our findings show that the α-Mn{sub 2}O{sub 3} material is a promising NO{sub x} adsorber for lean-burn exhausts even at low operating temperatures.

  16. NO adsorption behaviors of the MnOx catalysts in lean-burn atmospheres

    International Nuclear Information System (INIS)

    Guo, Li; Xian, Hui; Li, Qi-Feng; Chen, Da; Tan, Yi-Sheng; Zhang, Jing; Zheng, Li-Rong; Li, Xin-Gang

    2013-01-01

    Highlights: • α-Mn 2 O 3 is a promising NO x adsorber for lean-burn exhausts even at low temperatures. • NO x was weakly bonded on α-Mn 2 O 3 , but strongly bonded on β-MnO 2 . • NO could efficiently adsorb/desorb within the lean/rich cyclings over α-Mn 2 O 3 . • The superficial oxygen species plays a key role for the NO oxidation over α-Mn 2 O 3 . • The NO adsorption and oxidation follow the L–H and/or E–R mechanism over α-Mn 2 O 3 . -- Abstract: NO x emission control of lean-burn engines is one of the great challenges in the world. Herein, the MnO x model catalysts with the different calcination temperatures were synthesized to investigate their NO adsorbability for lean-burn exhausts. The transformation from (β-)MnO 2 to (α-)Mn 2 O 3 following the increased calcination temperatures was evidenced from the viewpoint of the local atomic level. Among these samples, the one calcined at 550 °C containing the single α-Mn 2 O 3 phase displayed the best NO adsorbability: NO was mainly adsorbed in the forms of NO/nitrites and NO 2 /nitrates at the low and high temperatures, respectively; the NO oxidation ability displayed the volcano-shape following the increased operating temperatures, and reached the maximum, i.e. 92.4% of the NO-to-NO 2 conversion, at 250 °C. Moreover, this sample presented the efficiently reversible NO adsorption/desorption performance in alternative lean-burn/fuel-rich atmospheres, due to the weakly bonded NO x on it. The superficial oxygen species plays a critical role for the NO oxidation over α-Mn 2 O 3 . The consumed superficial oxygen could be further compensated by the gaseous and lattice oxygen therein. Our findings show that the α-Mn 2 O 3 material is a promising NO x adsorber for lean-burn exhausts even at low operating temperatures

  17. Model predictive control of a lean-burn gasoline engine coupled with a passive selective catalytic reduction system

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Pingen [Tennessee Technological University (TTU); Lin, Qinghua [Tennessee Technological University (TTU); Prikhodko, Vitaly Y. [ORNL

    2017-10-01

    Lean-burn gasoline engines have demonstrated 10–20% engine efficiency gain over stoichiometric engines and are widely considered as a promising technology for meeting the 54.5 miles-per-gallon (mpg) Corporate Average Fuel Economy standard by 2025. Nevertheless, NOx emissions control for lean-burn gasoline for meeting the stringent EPA Tier 3 emission standards has been one of the main challenges towards the commercialization of highly-efficient lean-burn gasoline engines in the United States. Passive selective catalytic reduction (SCR) systems, which consist of a three-way catalyst and SCR, have demonstrated great potentials of effectively reducing NOx emissions for lean gasoline engines but may cause significant fuel penalty due to ammonia generation via rich engine combustion. The purpose of this study is to develop a model-predictive control (MPC) scheme for a lean-burn gasoline engine coupled with a passive SCR system to minimize the fuel penalty associated with passive SCR operation while satisfying stringent NOx and NH3 emissions requirements. Simulation results demonstrate that the MPC-based control can reduce the fuel penalty by 47.7% in a simulated US06 cycle and 32.0% in a simulated UDDS cycle, compared to the baseline control, while achieving over 96% deNOx efficiency and less than 15 ppm tailpipe ammonia slip. The proposed MPC control can potentially enable high engine efficiency gain for highly-efficient lean-burn gasoline engine while meeting the stringent EPA Tier 3 emission standards.

  18. Detailed characterization of particulate matter emitted by lean-burn gasoline direct injection engine

    Energy Technology Data Exchange (ETDEWEB)

    Zelenyuk, Alla [Pacific Northwest National Laboratory, Richland, WA, USA; Wilson, Jacqueline [Pacific Northwest National Laboratory, Richland, WA, USA; Imre, Dan [Imre Consulting, Richland, WA, USA; Stewart, Mark [Pacific Northwest National Laboratory, Richland, WA, USA; Muntean, George [Pacific Northwest National Laboratory, Richland, WA, USA; Storey, John [Oak Ridge National Laboratory, Knoxville, TN, USA; Prikhodko, Vitaly [Oak Ridge National Laboratory, Knoxville, TN, USA; Lewis, Samuel [Oak Ridge National Laboratory, Knoxville, TN, USA; Eibl, Mary [Oak Ridge National Laboratory, Knoxville, TN, USA; Parks, Jim [Oak Ridge National Laboratory, Knoxville, TN, USA

    2016-11-10

    This study presents detailed characterization of the chemical and physical properties of PM emitted by a 2.0L BMW lean-burn turbocharged GDI engine operated under a number of combustion strategies that include lean homogeneous, lean stratified, stoichiometric, and fuel rich conditions. We characterized PM number concentrations, size distributions, and the size, mass, compositions, and effective density of fractal and compact individual exhaust particles. For the fractal particles, these measurements yielded fractal dimension, average diameter of primary spherules, and number of spherules, void fraction, and dynamic shape factors as function of particle size. Overall, the PM properties were shown to vary significantly with engine operation condition. Lean stratified operation yielded the most diesel-like size distribution and the largest PM number and mass concentrations, with nearly all particles being fractal agglomerates composed of elemental carbon with small amounts of ash and organics. In contrast, stoichiometric operation yielded a larger fraction of ash particles, especially at low speed and low load. Three distinct forms of ash particles were observed, with their fractions strongly dependent on engine operating conditions: sub-50 nm ash particles, abundant at low speed and low load, ash-containing fractal particles, and large compact ash particles that significantly contribute to PM mass loadings

  19. Energy efficiency analyses of active flow aftertreatment systems for lean burn internal combustion engines

    International Nuclear Information System (INIS)

    Zheng Ming; Reader, Graham T.

    2004-01-01

    The use of three way catalytic converters in stoichiometric burn reciprocating internal combustion engine systems has proved to be an effective and efficient method for reducing the level of criteria pollutants. However, such passive systems have not been as successful in emission amelioration when combined with lean burn engines. This is because of the thermochemical nature of the exhaust gases generated by such engines. The high content of exhaust oxygen largely negates the effectiveness of three way catalytic converters, and the comparatively low temperature of the combusted gases means that supplemental energy has to be added to these gases to enable the converter to function correctly. This requirement severely reduces the energy efficiency of conventional passive aftertreatment systems. However, initial empirical studies have indicated that a possible means of improving the performance of aftertreatment devices when used with lean burn engine systems is to use active flow control of the exhaust gases. These results are reported in this paper. This concept has been further investigated by developing an energy efficiency analysis that enables the effects on aftertreatment performance of different gas flow rates, flow reversal frequencies and monolith solid properties to be investigated. Simulation results indicate that through active thermal management, the supplemental energy consumption can be drastically reduced

  20. Lean maturity, lean sustainability

    DEFF Research Database (Denmark)

    Jørgensen, Frances; Matthiesen, Rikke; Nielsen, Jacob

    2007-01-01

    . A framework for describing levels of lean capability is presented, based on a brief review of the literature and experiences from 12 Danish companies currently implementing lean. Although still in its emerging phase, the framework contributes to both theory and practice by describing developmental stages......Although lean is rapidly growing in popularity, its implementation is far from problem free and companies may experience difficulties sustaining long term success. In this paper, it is suggested that sustainable lean requires attention to both performance improvement and capability development...... that support lean capability development and consequently, lean sustainability....

  1. A comparison between EGR and lean-burn strategies employed in a natural gas SI engine using a two-zone combustion model

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Amr; Bari, Saiful [Sustainable Energy Centre, School of Advanced Manufacturing and Mechanical Engineering, Univ. of South Australia, Mawson Lakes SA 5095 (Australia)

    2009-12-15

    Exhaust gas recirculation (EGR) strategy has been recently employed in natural gas SI engines as an alternative to lean burn technique in order to satisfy the increasingly stringent emission standards. However, the effect of EGR on some of engine performance parameters compared to lean burn is not yet quite certain. In the current study, the effect of both EGR and lean burn on natural gas SI engine performance was compared at similar operating conditions. This was achieved numerically by developing a computer simulation of the four-stroke spark-ignition natural gas engine. A two-zone combustion model was developed to simulate the in-cylinder conditions during combustion. A kinetic model based on the extended Zeldovich mechanism was also developed in order to predict NO emission. The combustion model was validated using experimental data and a good agreement between the results was found. It was demonstrated that adding EGR to the stoichiometric inlet charge at constant inlet pressure of 130 kPa decreased power more rapidly than excess air; however, the power loss was recovered by increasing the inlet pressure from 130 kPa at zero dilution to 150 kPa at 20% EGR dilution. The engine fuel consumption increased by 10% when 20% EGR dilution was added at inlet pressure of 150 kPa compared to using 20% air dilution at 130 kPa. However, it was found that EGR dilution strategy is capable of producing extremely lower NO emission than lean burn technique. NO emission was reduced by about 70% when the inlet charge was diluted at a rate of 20% using EGR instead of excess air. (author)

  2. A comparison between EGR and lean-burn strategies employed in a natural gas SI engine using a two-zone combustion model

    International Nuclear Information System (INIS)

    Ibrahim, Amr; Bari, Saiful

    2009-01-01

    Exhaust gas recirculation (EGR) strategy has been recently employed in natural gas SI engines as an alternative to lean burn technique in order to satisfy the increasingly stringent emission standards. However, the effect of EGR on some of engine performance parameters compared to lean burn is not yet quite certain. In the current study, the effect of both EGR and lean burn on natural gas SI engine performance was compared at similar operating conditions. This was achieved numerically by developing a computer simulation of the four-stroke spark-ignition natural gas engine. A two-zone combustion model was developed to simulate the in-cylinder conditions during combustion. A kinetic model based on the extended Zeldovich mechanism was also developed in order to predict NO emission. The combustion model was validated using experimental data and a good agreement between the results was found. It was demonstrated that adding EGR to the stoichiometric inlet charge at constant inlet pressure of 130 kPa decreased power more rapidly than excess air; however, the power loss was recovered by increasing the inlet pressure from 130 kPa at zero dilution to 150 kPa at 20% EGR dilution. The engine fuel consumption increased by 10% when 20% EGR dilution was added at inlet pressure of 150 kPa compared to using 20% air dilution at 130 kPa. However, it was found that EGR dilution strategy is capable of producing extremely lower NO emission than lean burn technique. NO emission was reduced by about 70% when the inlet charge was diluted at a rate of 20% using EGR instead of excess air.

  3. Selective NOx Recirculation for Stationary Lean-Burn Natural Gas Engines

    Energy Technology Data Exchange (ETDEWEB)

    Nigel N. Clark

    2006-12-31

    Nitric oxide (NO) and nitrogen dioxide (NO2) generated by internal combustion (IC) engines are implicated in adverse environmental and health effects. Even though lean-burn natural gas engines have traditionally emitted lower oxides of nitrogen (NOx) emissions compared to their diesel counterparts, natural gas engines are being further challenged to reduce NOx emissions to 0.1 g/bhp-hr. The Selective NOx Recirculation (SNR) approach for NOx reduction involves cooling the engine exhaust gas and then adsorbing the NOx from the exhaust stream, followed by the periodic desorption of NOx. By sending the desorbed NOx back into the intake and through the engine, a percentage of the NOx can be decomposed during the combustion process. SNR technology has the support of the Department of Energy (DOE), under the Advanced Reciprocating Engine Systems (ARES) program to reduce NOx emissions to under 0.1 g/bhp-hr from stationary natural gas engines by 2010. The NO decomposition phenomenon was studied using two Cummins L10G natural gas fueled spark-ignited (SI) engines in three experimental campaigns. It was observed that the air/fuel ratio ({lambda}), injected NO quantity, added exhaust gas recirculation (EGR) percentage, and engine operating points affected NOx decomposition rates within the engine. Chemical kinetic model predictions using the software package CHEMKIN were performed to relate the experimental data with established rate and equilibrium models. The model was used to predict NO decomposition during lean-burn, stoichiometric burn, and slightly rich-burn cases with added EGR. NOx decomposition rates were estimated from the model to be from 35 to 42% for the lean-burn cases and from 50 to 70% for the rich-burn cases. The modeling results provided an insight as to how to maximize NOx decomposition rates for the experimental engine. Results from this experiment along with chemical kinetic modeling solutions prompted the investigation of rich-burn operating conditions

  4. Attempt of lean burn of a 4 cycle gasoline engine by the aid of low pressure air assisted in-cylinder injection; Tonai kuki nenryo funsha ni yoru lean burn no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Hatakeyama, S; Kondo, M; Sekiya, Y; Murayama, T [Hokkaido Automotive Engineering College, Hokkaido (Japan)

    1997-10-01

    Comparable performance and exhaust emission with conventional carburetor was obtained by a low Pressure air assisted in-cylinder injection system. And lean burn of idling and light load operation till A/F=70 was realized by installing a spark Plug and a reed type injection nozzle in a divided combustion chambaer of a 4 cycle gasoline engine. 2 refs., 10 figs.

  5. Effect of hydrogen addition on burning rate and surface density of turbulent lean premixed methane-air flames

    International Nuclear Information System (INIS)

    Guo, H.; Tayebi, B.; Galizzi, C.; Escudie, D.

    2009-01-01

    Hydrogen (H 2 ) is a clean burning component, but relatively expensive. Mixing a small amount of hydrogen with other fuels is an effective way to use H 2 . H 2 enriched combustion significantly improves fuel efficiency and reduces pollutant (nitrogen oxide and particulate matter) emissions. This presentation discussed the effect of hydrogen addition on burning rate and surface density of turbulent lean premixed methane-air flames. The presentation discussed flame configuration; the experimental methodology using laser tomography; and results for typical images, burning velocity, ratio of turbulent to laminar burning velocities, flame surface density, curvature, flame brush thickness, and integrated flame surface area. It was concluded that the increase of turbulent burning velocity was faster than that of laminar burning velocity, which contradicted traditional theory. figs.

  6. A study on the criterions of lean burn limit for an LPG EFI engine. Paper no. IGEC-1-140

    International Nuclear Information System (INIS)

    Li, L.; Wang, Z.; Xiao, Z.; Wang, H.; Deng, B.; Su, Y.

    2005-01-01

    Based on electronic low-pressure gaseous injection, the comparing analysis of several methods for the criterions of lean burn limit in an LPG engine is presented. Experiments are carried out in a single cylinder, four-stroke, water-cooled, 125cc engine with electronic LPG injection. According to the analysis of multi-parameters in and out cylinder, it shows that variation coefficient of indicated pressure which is the classical judgment of lean burn limit, the HC emission, HC emission rising gradient, the misfiring rate and the variation coefficient of the crank angle of the maximum combustion pressure can be as the criterions for lean burn limit. For the test engine, 15% as variation coefficient of indicative mean pressure, 500 x 10 -6 as HC emission, 2000 x 10 -6 as HC emission rising ratio, 1% as misfiring rate and 50% as variation coefficient of the crank angle of the maximum combustion pressure can be as the judgment criterions of LPG lean burn limits. (author)

  7. Nonlinear dynamics of cycle-to-cycle combustion variations in a lean-burn natural gas engine

    International Nuclear Information System (INIS)

    Li Guoxiu; Yao Baofeng

    2008-01-01

    Temporal dynamics of the combustion process in a lean-burn natural gas engine was studied by the analysis of time series of consecutive experimental in-cylinder pressure data in this work. Methods borrowed to the nonlinear dynamical system theory were applied to analyze the in-cylinder pressure time series under operating conditions with different equivalence ratio. Phase spaces were reconstructed from the in-cylinder pressure time series and Poincare section calculated from each phase space. Poincare sections show that the in-cylinder combustion process involves chaotic behavior. Furthermore, return maps plotted from time series of indicated mean effective pressure show that both nonlinear deterministic components and stochastic components are involved in the dynamics of cycle-to-cycle combustion variations in the lean burn natural gas engine. There is a transition from stochastic behavior to noisy nonlinear determinism as equivalence ratio decreases from near stoichiometric to very lean conditions

  8. Nonlinear dynamics of cycle-to-cycle combustion variations in a lean-burn natural gas engine

    Energy Technology Data Exchange (ETDEWEB)

    Li Guoxiu [School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China)], E-mail: gxli@bjtu.edu.cn; Yao Baofeng [School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China)

    2008-04-15

    Temporal dynamics of the combustion process in a lean-burn natural gas engine was studied by the analysis of time series of consecutive experimental in-cylinder pressure data in this work. Methods borrowed to the nonlinear dynamical system theory were applied to analyze the in-cylinder pressure time series under operating conditions with different equivalence ratio. Phase spaces were reconstructed from the in-cylinder pressure time series and Poincare section calculated from each phase space. Poincare sections show that the in-cylinder combustion process involves chaotic behavior. Furthermore, return maps plotted from time series of indicated mean effective pressure show that both nonlinear deterministic components and stochastic components are involved in the dynamics of cycle-to-cycle combustion variations in the lean burn natural gas engine. There is a transition from stochastic behavior to noisy nonlinear determinism as equivalence ratio decreases from near stoichiometric to very lean conditions.

  9. Air-fuel ratio control of a lean burn Si engine using fuzzy self tuning method

    International Nuclear Information System (INIS)

    Akhlaghi, M.; Bakhtiari Nejad, F.; Azadi, S.

    2000-01-01

    Reducing the exhaust emission of an spark ignition engine by means of engine modifications requires consideration of the effects of these modifications on the variations of crankshaft torque and the engine roughness respectively. Only if the roughness does not exceed a certain level the vehicle do not begin to surge. This paper presents a method for controlling the air-fuel ratio for a lean burn engine. Fuzzy rules and reasoning are utilized on-line to determine the control parameters. The main advantages of this method are simple structure and robust performance in a wide range of operating conditions. A non-linear model of an Si engine with the engine torque irregularity simulation is used in this study

  10. Plasma-assisted heterogeneous catalysis for NOx reduction in lean-burn engine exhaust

    Energy Technology Data Exchange (ETDEWEB)

    Penetrante, B.M.; Hsaio, M.C.; Merritt, B.T.; Vogtlin, G.E. [Lawrence Livermore National Lab., CA (United States); Wan, C.Z.; Rice, G.W.; Voss, K.E. [Engelhard Corp., Iselin, NJ (United States)

    1997-12-31

    This paper discusses the combination of a plasma with a catalyst to improve the reduction of NO{sub x} under lean-burn conditions. The authors have been investigating the effects of a plasma on the NO{sub x} reduction activity and temperature operating window of various catalytic materials. One of the goals is to develop a fundamental understanding of the interaction between the gas-phase plasma chemistry and the heterogeneous chemistry on the catalyst surface. The authors have observed that plasma assisted heterogeneous catalysis can facilitate NO{sub x} reduction under conditions that normally make it difficult for either the plasma or the catalyst to function by itself. By systematically varying the plasma electrode and catalyst configuration, they have been able to elucidate the process by which the plasma chemistry affects the chemical reduction of NO{sub x} on the catalyst surface. They have discovered that the main effect of the plasma is to induce the gas-phase oxidation of NO to NO{sub 21}. The reduction of NO{sub x} to N{sub 2} is then accomplished by heterogeneous reaction of O with activated hydrocarbons on the catalyst surface. The use of a plasma opens the opportunity for a new class of catalysts that are potentially more durable, more active, more selective and more sulfur-tolerant compared to conventional lean-NO{sub x} catalysts.

  11. Investigation of combustion and thermodynamic performance of a lean burn catalytic combustion gas turbine system

    International Nuclear Information System (INIS)

    Yin Juan; Weng Yiwu

    2011-01-01

    The goals of this research were to investigate the combustion and thermodynamic performance of a lean burn catalytic combustion gas turbine. The characteristics of lean burn catalytic combustion were investigated by utilising 1D heterogeneous plug flow model which was validated by experiments. The effects of operating parameters on catalytic combustion were numerically analysed. The system models were built in ASPEN Plus and three independent design variables, i.e. compressor pressure ratio (PR), regenerator effectiveness (RE) and turbine inlet temperature (TIT) were selected to analyse the thermodynamic performance of the thermal cycle. The main results show that: simulations from 1D heterogeneous plug flow model can capture the trend of catalytic combustion and describe the behavior of the catalytic monolith in detail. Inlet temperature is the most significant parameter that impacts operation of the catalytic combustor. When TIT and RE are constant, the increase of PR results in lowering the inlet temperature of the catalytic combustor, which results in decreasing methane conversion. The peak thermal efficiency and the optimal PR at a constant TIT increase with the increase of TIT; and at the constant PR, the thermal efficiency increases with the increase of TIT. However, with lower TIT conditions, the optimal PR and the peak efficiency at a constant TIT of the LBCCGT cycle are relative low to that of the conventional cycle. When TIT and PR are constant, the decrease of RE may result in lower methane conversion. The influences of RE on the methane conversion and the thermal efficiency are more significant at higher PRs. The higher thermal efficiency for the lower RE is achieved at lower PR.

  12. Multi-stage selective catalytic reduction of NOx in lean burn engine exhaust

    Energy Technology Data Exchange (ETDEWEB)

    Penetrante, B.M.; Hsaio, M.C.; Merritt, B.T.; Vogtlin, G.E. [Lawrence Livermore National Lab., CA (United States)

    1997-12-31

    Many studies suggest that the conversion of NO to NO{sub 2} is an important intermediate step in the selective catalytic reduction (SCR) of NO{sub x} to N{sub 2}. Some effort has been devoted to separating the oxidative and reductive functions of the catalyst in a multi-stage system. This method works fine for systems that require hydrocarbon addition. The hydrocarbon has to be injected between the NO oxidation catalyst and the NO{sub 2} reduction catalyst; otherwise, the first-stage oxidation catalyst will also oxidize the hydrocarbon and decrease its effectiveness as a reductant. The multi-stage catalytic scheme is appropriate for diesel engine exhausts since they contain insufficient hydrocarbons for SCR, and the hydrocarbons can be added at the desired location. For lean-burn gasoline engine exhausts, the hydrocarbons already present in the exhausts will make it necessary to find an oxidation catalyst that can oxidize NO to NO{sub 2} but not oxidize the hydrocarbon. A plasma can also be used to oxidize NO to NO{sub 2}. Plasma oxidation has several advantages over catalytic oxidation. Plasma-assisted catalysis can work well for both diesel engine and lean-burn gasoline engine exhausts. This is because the plasma can oxidize NO in the presence of hydrocarbons without degrading the effectiveness of the hydrocarbon as a reductant for SCR. In the plasma, the hydrocarbon enhances the oxidation of NO, minimizes the electrical energy requirement, and prevents the oxidation of SO{sub 2}. This paper discusses the use of multi-stage systems for selective catalytic reduction of NO{sub x}. The multi-stage catalytic scheme is compared to the plasma-assisted catalytic scheme.

  13. Development II of ion current combustion control system. Application to the lean burn system of the micro vehicle engine; Ion denryu wo mochiita nensho seigyo system no kaihatsu. 2. Keijidosha engine wo mochiita lean burn eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Iida, T; Asano, M; Kajitani, M; Kuma, t; Morinaga, Y [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1997-10-01

    The lean bum engine has not been introduced into the micro vehicle so far because of the low cost requirement and small displacement, in spite of it is one of the effective solutions which increase the fuel economy. By the way, we had already reported in the former paper that we developed the ion current combustion control system the architecture of which is cheaper than the other system. In this paper, we described the way how the above system is applied to the lean burn system of the micro vehicle engine and also we reported the gain of fuel economy and the exhaust emission level. 5 refs., 11 figs., 2 tabs.

  14. Influence of cooled exhaust gas recirculation on performance, emissions and combustion characteristics of LPG fuelled lean burn SI engine

    Science.gov (United States)

    Ravi, K.; Pradeep Bhasker, J.; Alexander, Jim; Porpatham, E.

    2017-11-01

    On fuel perspective, Liquefied Petroleum Gas (LPG) provides cleaner emissions and also facilitates lean burn signifying less fuel consumption and emissions. Lean burn technology can attain better efficiencies and lesser combustion temperatures but this temperature is quite sufficient to facilitate formation of nitrogen oxide (NOx). Exhaust Gas Recirculation (EGR) for NOx reduction has been considered allover but extremely little literatures exist on the consequence of EGR on lean burn LPG fuelled spark ignition (SI) engine. The following research is carried out to find the optimal rate of EGR addition to reduce NOx emissions without settling on performance and combustion characteristics. A single cylinder diesel engine is altered to operate as LPG fuelled SI engine at a compression ratio of 10.5:1 and arrangements to provide different ratios of cooled EGR in the intake manifold. Investigations are done to arrive at optimum ratio of the EGR to reduce emissions without compromising on performance. Significant reductions in NOx emissions alongside HC and CO emissions were seen. Higher percentages of EGR further diluted the charge and lead to improper combustion and thus increased hydrocarbon emissions. Cooled EGR reduced the peak in-cylinder temperature which reduced NOx emissions but lead to misfire at lower lean limits.

  15. Temperature and air-fuel ratio dependent specific heat ratio functions for lean burned and unburned mixture

    International Nuclear Information System (INIS)

    Ceviz, M.A.; Kaymaz, I.

    2005-01-01

    The most important thermodynamic property used in heat release calculations for engines is the specific heat ratio. The functions proposed in the literature for the specific heat ratio are temperature dependent and apply at or near stoichiometric air-fuel ratios. However, the specific heat ratio is also influenced by the gas composition in the engine cylinder and especially becomes important for lean combustion engines. In this study, temperature and air-fuel ratio dependent specific heat ratio functions were derived to minimize the error by using an equilibrium combustion model for burned and unburned mixtures separately. After the error analysis between the equilibrium combustion model and the derived functions is presented, the results of the global specific heat ratio function, as varying with mass fraction burned, were compared with the proposed functions in the literature. The results of the study showed that the derived functions are more feasible at lean operating conditions of a spark ignition engine

  16. The Effect of Humidity on the Knock Behavior in a Medium BMEP Lean-Burn High-Speed Gas Engine

    NARCIS (Netherlands)

    van Essen, Vincent Martijn; Gersen, Sander; van Dijk, Gerco; Mundt, Torsten; Levinsky, Howard

    2016-01-01

    The effects of air humidity on the knock characteristics of fuels are investigated in a lean-burn, high-speed medium BMEP engine fueled with a CH4 + 4.7 mole% C3H8 gas mixture. Experiments are carried out with humidity ratios ranging from 4.3 to 11 g H2O/kg dry air. The measured pressure profiles at

  17. Investing in lean to improve basic capabilities: A strategy for system supply?

    Directory of Open Access Journals (Sweden)

    Inga-Lill Carlsson

    2017-04-01

    Full Text Available Purpose: This paper describes the perceived effects of implementing lean production in a Swedish SME contract manufacturer. Especially focused are the effects on, and possible trade-offs between, cost-efficiency and flexibility. Design/methodology/approach: SME suppliers need basic capabilities of qualitative production performance which may then be stepping-stones to develop more system supplier capabilities for added customer value: leadership to manage systems and processes, SCM, communications and relations management. Development of stable production processes is seen as a way to reach stable basic performance, efficient and with higher resource utilization. Quality is a precursor to delivery performance as well as to cost reduction and flexibility. This is a longitudinal single case study of a SME supplier striving to become a system supplier. Two main sources of data collection are used: interviews and the main author’s presence as employee and business developer, participating in and following up the ongoing change process. Findings: Two specific findings appeared: (1 An initial effect was an important “eye-opener” for the balance between cost efficiency and flexibility in the organization. (2 Process orientation, as the basis of both lean and agile approaches, allows many improvements without any conflicts or trade-offs between these two goals. Stability in the production leads to increased controllability, initially resulting in both higher cost-efficiency and higher flexibility. As the organization develops however, strategic considerations relating to the chosen market strategy might occur: cost leadership or differentiation.    Research limitations/implications: These results reflect the experiences of one SME supplier and further studies are needed for generalizability. Originality/value: The study increases the understanding of how a SME may develop stable processes in its different supplier-customer contexts. The study

  18. Selective NOx Recirculation for Stationary Lean-Burn Natural Gas Engines

    Energy Technology Data Exchange (ETDEWEB)

    Nigel Clark; Gregory Thompson; Richard Atkinson; Richard Turton; Chamila Tissera; Emre Tatli; Andy Zimmerman

    2005-12-28

    Selective NOx Recirculation (SNR) involves cooling the engine exhaust gas and then adsorbing the oxides of nitrogen (NOx) from the exhaust stream, followed by the periodic desorption of NOx. By returning the desorbed, concentrated NOx into the engine intake and through the combustion chamber, a percentage of the NOx is decomposed during the combustion process. An initial study of NOx decomposition during lean-burn combustion was concluded in 2004 using a 1993 Cummins L10G 240hp natural gas engine. It was observed that the air/fuel ratio, injected NO (nitric oxide) quantity and engine operating points affected NOx decomposition rates of the engine. Chemical kinetic modeling results were also used to determine optimum NOx decomposition operating points and were published in the 2004 annual report. A NOx decomposition rate of 27% was measured from this engine under lean-burn conditions while the software model predicted between 35-42% NOx decomposition for similar conditions. A later technology 1998 Cummins L10G 280hp natural gas engine was procured with the assistance of Cummins Inc. to replace the previous engine used for 2005 experimental research. The new engine was equipped with an electronic fuel management system with closed-loop control that provided a more stable air/fuel ratio control and improved the repeatability of the tests. The engine was instrumented with an in-cylinder pressure measurement system and electronic controls, and was adapted to operate over a range of air/fuel ratios. The engine was connected to a newly commissioned 300hp alternating current (AC) motoring dynamometer. The second experimental campaign was performed to acquire both stoichiometric and slightly rich (0.97 lambda ratio) burn NOx decomposition rates. Effects of engine load and speed on decomposition were quantified, but Exhaust Gas Recirculation (EGR) was not varied independently. Decomposition rates of up to 92% were demonstrated. Following recommendations at the 2004 ARES peer

  19. Managing paradoxical tensions during the implementation of Lean capabilities for improvement

    DEFF Research Database (Denmark)

    Maalouf, Malek Miguel; Gammelgaard, Britta

    2016-01-01

    Purpose: – Through the identification and investigation of the organisational paradoxes in lean, the purpose of this paper is to deepen the understanding of lean implementation intricacies, and contribute to sustaining lean in companies. Design/methodology/approach: – Case study based on semi...... also points to a range managerial responses used for dealing with the three paradoxes and facilitating lean transformation. Research limitations/implications: – This is a theory development paper which increases the understanding regarding the role of the organisational paradoxes in facilitating...

  20. Cellular burning in lean premixed turbulent hydrogen-air flames: Coupling experimental and computational analysis at the laboratory scale

    International Nuclear Information System (INIS)

    Day, M S; Bell, J B; Beckner, V E; Lijewski, M J; Cheng, R K; Tachibana, S

    2009-01-01

    One strategy for reducing US dependence on petroleum is to develop new combustion technologies for burning the fuel-lean mixtures of hydrogen or hydrogen-rich syngas fuels obtained from the gasification of coal and biomass. Fuel-flexible combustion systems based on lean premixed combustion have the potential for dramatically reducing pollutant emissions in transportation systems, heat and stationary power generation. However, lean premixed flames are highly susceptible to fluid-dynamical combustion instabilities making robust and reliable systems difficult to design. Low swirl burners are emerging as an important technology for meeting design requirements in terms of both reliability and emissions for next generation combustion devices. In this paper, we present simulations of a lean, premixed hydrogen flame stabilized on a laboratory-scale low swirl burner. The simulations use detailed chemistry and transport without incorporating explicit models for turbulence or turbulence/chemistry interaction. Here we discuss the overall structure of the flame and compare with experimental data. We also use the simulation data to elucidate the characteristics of the turbulent flame interaction and how this impacts the analysis of experimental measurements.

  1. Catalytic reduction of methane/unburned hydrocarbons in smoke from lean-burn gas engines

    International Nuclear Information System (INIS)

    Wit, Jan de.

    1999-01-01

    The aim of this project has been: To describe the flue gas conditions of typical stationary gas engines for cogeneration; To evaluate the predominant causes of deactivation of oxidation catalysts under realistic operation conditions; To develop improved long-term stable oxidation catalysts; To evaluate alternative catalyst-based methane reduction technologies. Most gas engines for stationary purposes are efficient lean-burn gas engines. Both the high efficiency and the very lean operation lead to low exhaust temperatures. However, there is now a tendency to design engines with un-cooled exhaust manifolds. This leads to higher shaft efficiency and increases the exhaust temperature. Exhaust gas composition and temperatures during continuous operation and start/stops are given in this report. Analyses have been made of catalyst samples to find predominant causes for oxidation catalyst deactivation. The analyses have shown that the presence of sulphur dioxide in the flue gas causes sulphur poisoning on the active catalyst surface. This effect is dependent on both the catalyst formulation and the catalyst support material composition. Neither sintering, nor other poisoning components than sulphur have been on the examined catalyst samples. The sulphur dioxide in the exhaust is a result of the sulphur in the odorisation additive used in the natural gas (approx. 10 mg/n 3 m THT) and of the sulphur present in combusted lubrication oil. These sources leads to a level of approx. 0.3 - 0.6 ppm (vol) SO 2 in the exhaust gas. Based on a large number of laboratory tests, a new oxidation catalyst formulation has been developed and successfully tested over 5000 hours of operation at a commercial cogeneration plant. This long-term testing has been additionally supplemented by short-term testings at test sites to see performance under other operation conditions. It has been shown that a rise in flue gas temperature (from e.g. 450 deg. C) will significantly reduce the necessary

  2. A Laser Spark Plug Ignition System for a Stationary Lean-Burn Natural Gas Reciprocating Engine

    Energy Technology Data Exchange (ETDEWEB)

    McIntyre, D. L. [West Virginia Univ., Morgantown, WV (United States)

    2007-05-01

    To meet the ignition system needs of large bore, high pressure, lean burn, natural gas engines a side pumped, passively Q-switched, Nd:YAG laser was developed and tested. The laser was designed to produce the optical intensities needed to initiate ignition in a lean burn, high compression engine. The laser and associated optics were designed with a passive Q-switch to eliminate the need for high voltage signaling and associated equipment. The laser was diode pumped to eliminate the need for high voltage flash lamps which have poor pumping efficiency. The independent and dependent parameters of the laser were identified and explored in specific combinations that produced consistent robust sparks in laboratory air. Prior research has shown that increasing gas pressure lowers the breakdown threshold for laser initiated ignition. The laser has an overall geometry of 57x57x152 mm with an output beam diameter of approximately 3 mm. The experimentation used a wide range of optical and electrical input parameters that when combined produced ignition in laboratory air. The results show a strong dependence of the output parameters on the output coupler reflectivity, Q-switch initial transmission, and gain media dopant concentration. As these three parameters were lowered the output performance of the laser increased leading to larger more brilliant sparks. The results show peak power levels of up to 3MW and peak focal intensities of up to 560 GW/cm2. Engine testing was performed on a Ricardo Proteus single cylinder research engine. The goal of the engine testing was to show that the test laser performs identically to the commercially available flashlamp pumped actively Q-switched laser used in previous laser ignition testing. The engine testing consisted of a comparison of the in-cylinder, and emissions behavior of the engine using each of the lasers as an ignition system. All engine parameters were kept as constant as possilbe while the equivalence ratio (fueling

  3. Effects of spark plug configuration on combustion and emission characteristics of a LPG fuelled lean burn SI engine

    Science.gov (United States)

    Ravi, K.; Khan, Manazir Ahmed; Pradeep Bhasker, J.; Porpatham, E.

    2017-11-01

    Introduction of technological innovation in automotive engines in reducing pollution and increasing efficiency have been under contemplation. Gaseous fuels have proved to be a promising way to reduce emissions in Spark Ignition (SI) engines. In particular, LPG settled to be a favourable fuel for SI engines because of their higher hydrogen to carbon ratio, octane rating and lower emissions. Wide ignition limits and efficient combustion characteristics make LPG suitable for lean burn operation. But lean combustion technology has certain drawbacks like poor flame propagation, cyclic variations etc. Based on copious research it was found that location, types and number of spark plug significantly influence in reducing cyclic variations. In this work the influence of single and dual spark plugs of conventional and surface discharge electrode type were analysed. Dual surface discharge electrode spark plug enhanced the brake thermal efficiency and greatly reduced the cyclic variations. The experimental results show that rate of heat release and pressure rise was more and combustion duration was shortened in this configuration. On the emissions front, the NOx emission has increased whereas HC and CO emissions were reduced under lean condition.

  4. Emission reductions through precombustion chamber design in a natural gas, lean burn engine

    International Nuclear Information System (INIS)

    Crane, M.E.; King, S.R.

    1992-01-01

    A study was conducted to evaluate the effects of various precombustion chamber design, operating and control parameters on the exhaust emissions of a natural gas engine. Analysis of the results showed that engine-out total hydrocarbons and oxides of nitrogen (NO x ) can be reduced, relative to conventional methods, through prechamber design. More specifically, a novel staged prechamber yielded significant reductions in NO x and total hydrocarbon emissions by promoting stable prechamber and main chamber ignition under fuel-lean conditions. Precise fuel control was also critical when balancing low emissions and engine efficiency (i.e., fuel economy). The purpose of this paper is to identify and explain positive and deleterious effects of natural gas prechamber design on exhaust emissions

  5. Burns

    Science.gov (United States)

    A burn is damage to your body's tissues caused by heat, chemicals, electricity, sunlight, or radiation. Scalds from hot ... and gases are the most common causes of burns. Another kind is an inhalation injury, caused by ...

  6. Conditioning of data for cyclic variation of IMEP under lean burn operation in a spark-ignition engine; Hibana tenka kikan no kihaku nensho untenji ni okeru zushi heikin yuko atsuryoku no hendo

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, K.; Urata, Y.; Yoshida, K.; Ono, t. [Honda Motor Co. Ltd., Tokyo (Japan)

    1997-07-25

    In this study, we investigated the relationship of indicated mean effective pressure (IMEP) for a spark ignition engine under lean combustion with the cyclic variation of mass fraction burned by measuring the energy release from the spark plug, intensity of the light emission from the flame and the cylinder pressure at the same time. In order to minimized an error in the initial and late combustion sages of the mass fraction burned to be obtained by cylinder pressure, spark plug energy and intensity of light emission were measured. As a result, it was found that there are three main causes of cyclic variation of IMEP. These consist of the burning speed during the initial stage of combustion, variation in the total mass fraction burned, and variation of the late burning during the late expansion stroke. Thus, we determined that there is a favorable interrelationship between the IMEPs and the corrected mass fraction burned. 13 refs., 9 figs., 1 tab.

  7. Cyclic variations of fuel-droplet distribution during the early intake stroke of a lean-burn stratified-charge spark-ignition engine

    Energy Technology Data Exchange (ETDEWEB)

    Aleiferis, P.G. [Imperial College London, Department of Mechanical Engineering, London (United Kingdom); University College London, Department of Mechanical Engineering, London (United Kingdom); Hardalupas, Y.; Taylor, A.M.K.P. [Imperial College London, Department of Mechanical Engineering, London (United Kingdom); Ishii, K. [Honda International Technical School, Saitama (Japan); Urata, Y. [Tochigi R and D Centre, Honda R and D Co., Ltd, Tochigi (Japan)

    2005-11-01

    Lean-burn spark-ignition engines exhibit higher efficiency and lower specific emissions in comparison with stoichiometrically charged engines. However, as the air-to-fuel (A/F) ratio of the mixture is made leaner than stoichiometric, cycle-by-cycle variations in the early stages of in-cylinder combustion, and subsequent indicated mean effective pressure (IMEP), become more pronounced and limit the range of lean-burn operation. Viable lean-burn engines promote charge stratification, the mixture near the spark plug being richer than the cylinder volume averaged value. Recent work has shown that cycle-by-cycle variations in the early stages of combustion in a stratified-charge engine can be associated with variations in both the local value of A/F ratio near the spark plug around ignition timing, as well as in the volume averaged value of the A/F ratio. The objective of the current work was to identify possible sources of such variability in A/F ratio by studying the in-cylinder field of fuel-droplet distribution during the early intake stroke. This field was visualised in an optical single-cylinder 4-valve pentroof-type spark-ignition engine by means of laser-sheet illumination in planes parallel to the cylinder head gasket 6 and 10 mm below the spark plug. The engine was run with port-injected isooctane at 1500 rpm with 30% volumetric efficiency and air-to-fuel ratio corresponding to both stoichiometric firing (A/F=15, {phi} =1.0) and mixture strength close to the lean limit of stable operation (A/F=22, {phi} =0.68). Images of Mie intensity scattered by the cloud of fuel droplets were acquired on a cycle-by-cycle basis. These were studied in order to establish possible correlations between the cyclic variations in size, location and scattered-light intensity of the cloud of droplets with the respective variations in IMEP. Because of the low level of Mie intensity scattered by the droplets and because of problems related to elastic scattering on the walls of the

  8. Study of the burning capability of the Los Alamos ATW system

    Energy Technology Data Exchange (ETDEWEB)

    Landeyro, P.A. [ENEA, Roma (Italy); Buccafurni, A.; Orazi, A. [ANPA, Roma (Italy)

    1995-10-01

    The aim of calculations is to evaluate the evolution of the infinate multiplication factor (k{sub inf}) during the irradiation of minor actinides, High Level Waste (HLWL) and Plutonium. The most important results are independently verified with Monte Carlo calculations. The relative importance of the main parameters affecting the k{sub inf} was investigated by performing calculations with several minor actinide and plutonium concentrations as well as different {sup 238}U decontamination factors for HLW. The merit figure value for minor actinide alone, considering a constant neutron flux indicates that the best results are reached for minor actinide concentration equal to PWR spent fuel. The best plutonium burning results are obtained for a concentration (50.23 g/l) equal to the half of PWR spent fuel one. The simulations lead to two different reactor concepts: one for HLW burning and the other for plutonium burning purposes. To burn the HLW the most suitable reactor is an homogeneous one. This kind of reactor can effectively be utilised to burn minor actinide in low concentration (namely the PWR spent fuel). On the other hand an heterogeneous reactor with channels filled by all actinides present in PWR spent fuel with the exclusion of U isotopes with a concentration of 50 g/l can be studied.

  9. Preparation Effects on the Performance of Silica-Doped Hydrous Titanium Oxide (HTO:Si)-Supported Pt Catalysts for Lean-Burn NOx Reduction by Hydrocarbons; TOPICAL

    International Nuclear Information System (INIS)

    GARDNER, TIMOTHY J.; MCLAUGHLIN, LINDA I.; MOWERY, DEBORAH L.; SANDOVAL, RONALD S.

    2002-01-01

    This report describes the development of bulk hydrous titanium oxide (HTO)- and silica-doped hydrous titanium oxide (HTO:Si)-supported Pt catalysts for lean-burn NOx catalyst applications. The effects of various preparation methods, including both anion and cation exchange, and specifically the effect of Na content on the performance of Pt/HTO:Si catalysts, were evaluated. Pt/HTO:Si catalysts with low Na content ( and lt; 0.5 wt.%) were found to be very active for NOx reduction in simulated lean-burn exhaust environments utilizing propylene as the major reductant species. The activity and performance of these low Na Pt/HTO:Si catalysts were comparable to supported Pt catalysts prepared using conventional oxide or zeolite supports. In ramp down temperature profile test conditions, Pt/HTO:Si catalysts with Na contents in the range of 3-5 wt.% showed a wide temperature window of appreciable NOx conversion relative to low Na Pt/HTO:Si catalysts. Full reactant species analysis using both ramp up and isothermal test conditions with the high Na Pt/HTO:Si catalysts, as well as diffuse reflectance FTIR studies, showed that this phenomenon was related to transient NOx storage effects associated with NaNO(sub 2)/NaNO(sub 3) formation. These nitrite/nitrate species were found to decompose and release NOx at temperatures above 300 C in the reaction environment (ramp up profile). A separate NOx uptake experiment at 275 C in NO/N(sub 2)/O(sub 2) showed that the Na phase was inefficiently utilized for NOx storage. Steady state tests showed that the effect of increased Na content was to delay NOx light-off and to decrease the maximum NOx conversion. Similar results were observed for high K Pt/HTO:Si catalysts, and the effects of high alkali content were found to be independent of the sample preparation technique. Catalyst characterization (BET surface area, H(sub 2) chemisorption, and transmission electron microscopy) was performed to elucidate differences between the HTO- and HTO

  10. Simultaneous NOx and hydrocarbon emissions control for lean-burn engines using low-temperature solid oxide fuel cell at open circuit.

    Science.gov (United States)

    Huang, Ta-Jen; Hsu, Sheng-Hsiang; Wu, Chung-Ying

    2012-02-21

    The high fuel efficiency of lean-burn engines is associated with high temperature and excess oxygen during combustion and thus is associated with high-concentration NO(x) emission. This work reveals that very high concentration of NO(x) in the exhaust can be reduced and hydrocarbons (HCs) can be simultaneously oxidized using a low-temperature solid oxide fuel cell (SOFC). An SOFC unit is constructed with Ni-YSZ as the anode, YSZ as the electrolyte, and La(0.6)Sr(0.4)CoO(3) (LSC)-Ce(0.9)Gd(0.1)O(1.95) as the cathode, with or without adding vanadium to LSC. SOFC operation at 450 °C and open circuit can effectively treat NO(x) over the cathode at a very high concentration in the simulated exhaust. Higher NO(x) concentration up to 5000 ppm can result in a larger NO(x) to N(2) rate. Moreover, a higher oxygen concentration promotes NO conversion. Complete oxidation of HCs can be achieved by adding silver to the LSC current collecting layer. The SOFC-based emissions control system can treat NO(x) and HCs simultaneously, and can be operated without consuming the anode fuel (a reductant) at near the engine exhaust temperature to eliminate the need for reductant refilling and extra heating.

  11. On the Experimental and Theoretical Investigations of Lean Partially Premixed Combustion, Burning Speed, Flame Instability and Plasma Formation of Alternative Fuels at High Temperatures and Pressures

    Science.gov (United States)

    Askari, Omid

    This dissertation investigates the combustion and injection fundamental characteristics of different alternative fuels both experimentally and theoretically. The subjects such as lean partially premixed combustion of methane/hydrogen/air/diluent, methane high pressure direct-injection, thermal plasma formation, thermodynamic properties of hydrocarbon/air mixtures at high temperatures, laminar flames and flame morphology of synthetic gas (syngas) and Gas-to-Liquid (GTL) fuels were extensively studied in this work. These subjects will be summarized in three following paragraphs. The fundamentals of spray and partially premixed combustion characteristics of directly injected methane in a constant volume combustion chamber have been experimentally studied. The injected fuel jet generates turbulence in the vessel and forms a turbulent heterogeneous fuel-air mixture in the vessel, similar to that in a Compressed Natural Gas (CNG) Direct-Injection (DI) engines. The effect of different characteristics parameters such as spark delay time, stratification ratio, turbulence intensity, fuel injection pressure, chamber pressure, chamber temperature, Exhaust Gas recirculation (EGR) addition, hydrogen addition and equivalence ratio on flame propagation and emission concentrations were analyzed. As a part of this work and for the purpose of control and calibration of high pressure injector, spray development and characteristics including spray tip penetration, spray cone angle and overall equivalence ratio were evaluated under a wide range of fuel injection pressures of 30 to 90 atm and different chamber pressures of 1 to 5 atm. Thermodynamic properties of hydrocarbon/air plasma mixtures at ultra-high temperatures must be precisely calculated due to important influence on the flame kernel formation and propagation in combusting flows and spark discharge applications. A new algorithm based on the statistical thermodynamics was developed to calculate the ultra-high temperature plasma

  12. The burnup capabilities of the Deep Burn Modular Helium Reactor analyzed by the Monte Carlo Continuous Energy Code MCB

    Energy Technology Data Exchange (ETDEWEB)

    Talamo, Alberto E-mail: alby@neutron.kth.se; Gudowski, Waclaw E-mail: wacek@neutron.kth.se; Venneri, Francesco E-mail: venneri@lanl.gov

    2004-01-01

    We have investigated the waste actinide burnup capabilities of a Gas Turbine Modular Helium Reactor (GT-MHR, similar to the reactor being designed by General Atomics and Minatom for surplus weapons plutonium destruction) with the Monte Carlo Continuous Energy Burnup Code MCB, an extension of MCNP developed at the Royal Institute of Technology in Stockholm and University of Mining and Metallurgy in Krakow. The GT-MHR is a gas-cooled, graphite-moderated reactor, which can be powered with a wide variety of fuels, like thorium, uranium or plutonium. In the present work, the GT-MHR is fueled with the transuranic actinides contained in Light Water Reactors (LWRs) spent fuel for the purpose of destroying them as completely as possible with minimum reliance on multiple reprocessing steps. After uranium extraction from the LWR spent fuel (UREX), the remaining waste actinides, including plutonium are partitioned into two distinct types of fuel for use in the GT-MHR: Driver Fuel (DF) and Transmutation Fuel (TF). The DF supplies the neutrons to maintain the fission chain reaction, whereas the TF emphasizes neutron capture to induce a deep burn transmutation and provide reactivity control by a negative feedback. When used in this mode, the GT-MHR is called Deep Burn Modular Helium Reactor (DB-MHR). Both fuels are contained in a structure of triple isotropic coated layers, TRISO coating, which has been proven to retain fission products up to 1600 deg. C and is expected to remain intact for hundreds of thousands of years after irradiation. Other benefits of this reactor consist of: a well-developed technology, both for the graphite-moderated core and the TRISO structure, a high energy conversion efficiency (about 50%), well established passive safety mechanism and a competitive cost. The destruction of more than 94% of {sup 239}Pu and the other geologically problematic actinide species makes this reactor a valid proposal for the reduction of nuclear waste and the prevention of

  13. The burnup capabilities of the Deep Burn Modular Helium Reactor analyzed by the Monte Carlo Continuous Energy Code MCB

    International Nuclear Information System (INIS)

    Talamo, Alberto; Gudowski, Waclaw; Venneri, Francesco

    2004-01-01

    We have investigated the waste actinide burnup capabilities of a Gas Turbine Modular Helium Reactor (GT-MHR, similar to the reactor being designed by General Atomics and Minatom for surplus weapons plutonium destruction) with the Monte Carlo Continuous Energy Burnup Code MCB, an extension of MCNP developed at the Royal Institute of Technology in Stockholm and University of Mining and Metallurgy in Krakow. The GT-MHR is a gas-cooled, graphite-moderated reactor, which can be powered with a wide variety of fuels, like thorium, uranium or plutonium. In the present work, the GT-MHR is fueled with the transuranic actinides contained in Light Water Reactors (LWRs) spent fuel for the purpose of destroying them as completely as possible with minimum reliance on multiple reprocessing steps. After uranium extraction from the LWR spent fuel (UREX), the remaining waste actinides, including plutonium are partitioned into two distinct types of fuel for use in the GT-MHR: Driver Fuel (DF) and Transmutation Fuel (TF). The DF supplies the neutrons to maintain the fission chain reaction, whereas the TF emphasizes neutron capture to induce a deep burn transmutation and provide reactivity control by a negative feedback. When used in this mode, the GT-MHR is called Deep Burn Modular Helium Reactor (DB-MHR). Both fuels are contained in a structure of triple isotropic coated layers, TRISO coating, which has been proven to retain fission products up to 1600 deg. C and is expected to remain intact for hundreds of thousands of years after irradiation. Other benefits of this reactor consist of: a well-developed technology, both for the graphite-moderated core and the TRISO structure, a high energy conversion efficiency (about 50%), well established passive safety mechanism and a competitive cost. The destruction of more than 94% of 239 Pu and the other geologically problematic actinide species makes this reactor a valid proposal for the reduction of nuclear waste and the prevention of

  14. Healthcare Lean.

    Science.gov (United States)

    Long, John C

    2003-01-01

    Lean Thinking is an integrated approach to designing, doing and improving the work of people that have come together to produce and deliver goods, services and information. Healthcare Lean is based on the Toyota production system and applies concepts and techniques of Lean Thinking to hospitals and physician practices.

  15. Lean production

    OpenAIRE

    Veselková, Jana

    2011-01-01

    The goal of this Bachelor's Thesis is to describe the general principles of lean production and afterwards apply these principles in a particular company. Due to the changing conditions on the world market is among companies growing concern about such innovative business systems. The theoretical part of this work deals with the general characteristics of lean production, including their history and focus on Toyota, as the originator of most lean systems. Mentioned are also the economic aspect...

  16. Negotiating Lean

    DEFF Research Database (Denmark)

    Rahbek Pedersen, Esben; Muniche, Mahad

    2011-01-01

    Purpose – The purpose of this paper is to analyse how negotiations between the constituencies affect the processes and outcomes of lean projects in Danish public sector organisations. Design/methodology/approach – The paper is based on a qualitative analysis of interviews with managers...... projects in the Danish public sector. It cannot be concluded that the findings can be generalised to reflect all types of lean projects across organisational and geographical settings. Originality/value – The paper adds value to the relatively scarce literature on lean management in the public sector...... and employees who have participated in lean projects in the Danish public sector. Negotiated order theory serves as the overarching theoretical framework for the analysis. Findings – The paper concludes that the processes and outcomes of lean depend not only on the technology itself, but also the negotiation...

  17. Model reduction of a lean NOx trap catalyst model

    NARCIS (Netherlands)

    Nauta, K.M.

    2008-01-01

    The desire to increase fuel efficiency and reduce carbon dioxide emissions of vehicles has led to an increased use of vehicles equipped with lean-burn engines, such as diesel and lean-burn gasoline engines. This type of engine uses excess oxygen when compared to the amount required to

  18. Lean Management

    OpenAIRE

    Picot, Arnold

    1994-01-01

    In this article the possibility of increase of competitiveness of the domestic enterprises by means of Lean management system is considered, and also the analysis of introduction of the mentioned system at the Russian enterprises is carried out. Besides, the key conditions necessary for successful introduction of system are presented. Lean management is a world-spread way of solving the problems, aimed at making the company competitive; it is the organized activity of staff of the company, fo...

  19. EDUCATION FOR LEAN & LEAN FOR EDUCATION: A LITERATURE REVIEW

    Directory of Open Access Journals (Sweden)

    Saveta Vukadinovic

    2017-03-01

    Full Text Available The purpose of this paper is to investigate and understand how tools and principles of Lean philosophy can be adopted to improve the effectiveness of engineering education by providing services beyond the competition and costs below the competition, and how engineering education can provide better prepared engineering professionals capable to work in dynamic Lean environments by developing multidisciplinary knowledge and skills. Paper will be based on analysis of relevant scientific and professional literature sources, including certain elements of description, classification, explanation and prediction. The authors will use detailed literature review to explain complex relationship and interdependence between Lean philosophy and engineering education and answer the question what benefits modern Lean enterprises may expect from properly educated and qualified engineers and how application of Lean tools and principles can improve the system of engineering education.

  20. Développement d'un moteur 4-soupapes fonctionnant en mélange dilué. Une nouvelle approche basée sur l'optimisation de l'aérodynamique interne Application of Flow Field Optimization to Lean Burn Engine Development. A New Approach Based on Internal Flow Field Optimization

    Directory of Open Access Journals (Sweden)

    Henriot S.

    2006-11-01

    emissions, and in lower specific fuel consumption. On the other hand, unburnt hydrocarbon (HC emissions generally increase, which implies the use of an oxidation catalyst if the antipollution standards become too severe. The first phase was to analyze the interactions between fluid dynamics and combustion, which determine the capability of this engine to run with a lean or dilute mixture. The methodology relies on complementary means :(a Three-dimensional computer code (KIVA. (b Optical diagnostics (Laser Doppler Velocimetry. (c Single-cylinder engine equipped with conventional measurement systems. Three dimensional modeling is used to predict and to optimize fluid motion in the cylinder for different intake configurations. The most important parameters influencing the stability of initial combustion are found to be the direction and magnitude of the mean velocity at the spark location, and the turbulence level. We should note that this flow field optimization is also applicable for operation with any dilute mixture (diluted by exhaust gases for example. The question of the minimization of the cyclic variability remains. The most favorable configuration for lean-burn operation was a pent-roof combustion chamber with a single operating intake valve. Fluid motion in this engine is characterized by the combination of a swirling and a tumbling motion and can be described as an inclined tumble. This motion leads to a flow at the spark plug location directed along the edge of the cylinder head. Moreover, the turbulence level is optimal for a high burning rate and low cycleto-cycle instability. The second phase was to apply this solution to a multicylinder system. The main difficulties came from the variability between cylinders, which was amplified during lean-burn operation. Each cylinder must be independently controlled (spark timing, sequential injection, fuel-air ratio, etc. . Moreover, an increased spark gap is needed in order to reproduce the performance (i. e. efficiency

  1. The relative effects of fuel concentration, residual-gas fraction, gas motion, spark energy and heat losses to the electrodes on flame-kernel development in a lean-burn spark ignition engine

    Energy Technology Data Exchange (ETDEWEB)

    Aleiferis, P.G.; Taylor, A.M.K.P. [Imperial College of Science, Technology and Medicine, London (United Kingdom). Dept. of Mechanical Engineering; Ishii, K. [Honda International Technical School, Saitama (Japan); Urata, Y. [Honda R and D Co., Ltd., Tochigi (Japan). Tochigi R and D Centre

    2004-04-01

    The potential of lean combustion for the reduction in exhaust emissions and fuel consumption in spark ignition engines has long been established. However, the operating range of lean-burn spark ignition engines is limited by the level of cyclic variability in the early-flame development stage that typically corresponds to the 0-5 per cent mass fraction burned duration. In the current study, the cyclic variations in early flame development were investigated in an optical stratified-charge spark ignition engine at conditions close to stoichiometry [air-to-fuel ratio (A/F) = 15] and to the lean limit of stable operation (A/F = 22). Flame images were acquired through either a pentroof window ('tumble plane' of view) or the piston crown ('swirl plane' of view) and these were processed to calculate the intra-cycle flame-kernel radius evolution. In order to quantify the relative effects of local fuel concentration, gas motion, spark-energy release and heat losses to the electrodes on the flame-kernel growth rate, a zero-dimensional flame-kernel growth model, in conjunction with a one-dimensional spark ignition model, was employed. Comparison of the calculated flame-radius evolutions with the experimental data suggested that a variation in A/F around the spark plug of {delta}(A/F) {approx} 4 or, in terms of equivalence ratio {phi}, a variation in {delta}{phi} {approx} 0.15 at most was large enough to account for 100 per cent of the observed cyclic variability in flame-kernel radius. A variation in the residual-gas fraction of about 20 per cent around the mean was found to account for up to 30 per cent of the variability in flame-kernel radius at the timing of 5 per cent mass fraction burned. The individual effect of 20 per cent variations in the 'mean' in-cylinder velocity at the spark plug at ignition timing was found to account for no more than 20 per cent of the measured cyclic variability in flame kernel radius. An individual effect of

  2. Lean healthcare.

    Science.gov (United States)

    Weinstock, Donna

    2008-01-01

    As healthcare organizations look for new and improved ways to reduce costs and still offer quality healthcare, many are turning to the Toyota Production System of doing business. Rather than focusing on cutting personnel and assets, "lean healthcare" looks to improve patient satisfaction through improved actions and processes.

  3. Development of lean burn gas engines using pilot fuel for ignition source; Developpement d'un moteur a gaz avec pre-injection de carburant pour la source d'allumage

    Energy Technology Data Exchange (ETDEWEB)

    Sakonji, T.; Saito, H.; Sakurai, T. [Tokyo Gas Co., Ltd. (Japan); Hirashima, T.; Kanno, K. [Nissan Diesel Motor Co., Ltd. (Japan)

    2000-07-01

    A development was conducted to investigate the performance of an open chamber gas engine with pilot fuel for ignition source. Experiments were conducted by using a gas engine equipped with a common-rail injection system. Main gas fuel is supplied to the engine cylinder, and then a small quantity of diesel fuel (approximately 1 % of total fuel energy input) was injected into the main chamber for ignition. The single cylinder prototype gas engine has demonstrated superior performance, such as, a shaft-end thermal efficiency of 36.7% with NO{sub x} level of 0.4 g/kW-h, which equals those of conventional spark ignited pre-chamber lean burn gas engines. For the next step, the multi-cylinder gas engine has been developed. That has 138 mm bore, 142 mm stroke, V8 configuration and 229 kW engine output 1500 rpm. This engine can also run with only diesel fuel for Standby-Power-Concurrent Co-generation. (authors)

  4. Lean consumption.

    Science.gov (United States)

    Womack, James P; Jones, Daniel T

    2005-03-01

    During the past 20 years, the real price of most consumer goods has fallen worldwide, the variety of goods and the range of sales channels offering them have continued to grow, and product quality has steadily improved. So why is consumption often so frustrating? It doesn't have to be--and shouldn't be--the authors say. They argue that it's time to apply lean thinking to the processes of consumption--to give consumers the full value they want from goods and services with the greatest efficiency and the least pain. Companies may think they save time and money by off-loading work to the consumer but, in fact, the opposite is true. By streamlining their systems for providing goods and services, and by making it easier for customers to buy and use those products and services, a growing number of companies are actually lowering costs while saving everyone time. In the process, these businesses are learning more about their customers, strengthening consumer loyalty, and attracting new customers who are defecting from less user-friendly competitors. The challenge lies with the retailers, service providers, manufacturers, and suppliers that are not used to looking at total cost from the standpoint of the consumer and even less accustomed to working with customers to optimize the consumption process. Lean consumption requires a fundamental shift in the way companies think about the relationship between provision and consumption, and the role their customers play in these processes. It also requires consumers to change the nature of their relationships with the companies they patronize. Lean production has clearly triumphed over similar obstacles in recent years to become the dominant global manufacturing model. Lean consumption, its logical companion, can't be far behind.

  5. Multi-Element Lean Direct Injection Combustor Module, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a Multi-Element Lean Direct Injection, ME-LDI, Combustion concept with the following innovative features: 1. Independent, mini burning zones...

  6. Influence of Co or Ce addition on the NOx storage and sulfur-resistance performance of the lean-burn NOx trap catalyst Pt/K/TiO{sub 2}-ZrO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Zou Zhiqiang [Tianjin Key Laboratory of Applied Catalysis Science and Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Meng, Ming, E-mail: mengm@tju.edu.cn [Tianjin Key Laboratory of Applied Catalysis Science and Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Tsubaki, Noritatsu [Department of Applied Chemistry, School of Engineering, University of Toyama, Gofuku 3190, Toyama city, Toyama 930 8555 (Japan); He Junjun; Wang Gang; Li Xingang; Zhou Xiaoyan [Tianjin Key Laboratory of Applied Catalysis Science and Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

    2009-10-15

    The Pt/K/TiO{sub 2}-ZrO{sub 2} catalysts promoted by Co or Ce were prepared by successive impregnation or mechanically mixing method. The influence of Co or Ce addition on the NOx storage and sulfur-resistance performance of the catalyst was investigated carefully. The techniques of XRD, FT-IR, in-situ DRIFTS, H{sub 2}-TPR and XPS were employed for catalyst characterization. The Co or Ce addition can greatly improve the NOx storage capacity of Pt/K/TiO{sub 2}-ZrO{sub 2} due to the enhanced oxidation ability and the release of more K sites. Ce addition induces higher K/Ti atomic ratio and larger NOx storage capacity as compared with Co addition. After sulfation and regeneration, the promoted catalysts shows more or less decreased NSC than Pt/K/TiO{sub 2}-ZrO{sub 2} due to the formation of more sulfates, especially for the Co-promoted catalysts, which possess better oxidation ability and facilitate the formation of large sulfates. The effect of Ce addition on Pt/K/TiO{sub 2}-ZrO{sub 2} largely depends on the addition mode. The high oxidation ability and the high K/Ti ratio of the mechanically prepared Ce-promoted catalyst make it still possess considerable NOx storage capacity (NSC) of 142 {mu}mol/g after sulfation and regeneration. With the decrease of sulfur content in fuels, the Co- and Ce-promoted catalysts possessing large NOx storage capacity, will be applicable to the purification of lean-burn NOx.

  7. Catalytic removal of methane and NO{sub x} in lean-burn natural-gas engine exhaust; Elimination par catalyse du methane et des NO{sub x} dans les echappements de moteur au gaz naturel a basse combustion

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Satokawa, S.; Yahagi, M.; Yamaseki, K.; Hoshi, F.; Uchida, H.; Yokota, H. [Tokyo Gas Co., Ltd. (Japan)

    2000-07-01

    We have developed a new catalytic system to reduce the emissions of hydrocarbons, carbon monoxide (CO), and nitrogen oxides (NO{sub x}) contained in the exhaust gases from a lean-burn natural-gas engine. Catalytic oxidation of unburned hydrocarbons and CO in the exhaust has been studied for noble metals supported on alumina. (1) A low-loading catalyst comprising platinum supported on alumina (Pt/alumina) was efficient for the oxidation of CO and hydrocarbons without methane. The CO conversions were maintained at more than 98 % for 20,000 hours over the Pt/alumina. (2) A catalyst comprising platinum and palladium supported on alumina (Pt-Pd/alumina) exhibited higher levels of oxidation of hydrocarbons (including methane) than a catalyst comprising only palladium supported on alumina (Pd/alumina). Its oxidation also lasted longer. The combined effects of the platinum and palladium metals achieved high sulfur dioxide resistance. Increasing the palladium content in the Pt-Pd/alumina catalyst increased the level of oxidation and extended the lifetime of the catalyst. (3) A catalyst comprising silver supported on alumina (Ag/alumina) was effective at reducing the amount of NO{sub X} by using the unburned hydrocarbons in the exhaust gas. The NO{sub x} conversions over Ag/alumina were maintained at more than 30 % for 3,500 hours. We describe a total clean-up system consisting of a Ag/alumina catalyst and a Pt-Pd/alumina catalyst in series on the exhaust gas stream. (authors)

  8. A produção enxuta como fator diferencial na capacidade de fornecimento de PMEs Lean production as a tool to improve the supply capability of the SMEs

    Directory of Open Access Journals (Sweden)

    Maria Letícia Sousa Correia Lima

    2003-01-01

    Full Text Available Face ao processo de reestruturação produtiva que a indústria automotiva brasileira tem vivenciado, notadamente a partir dos anos 1990, e à influência da filosofia enxuta de produção neste, o presente artigo traz um estudo realizado em pequenas e médias empresas (PMEs gaúchas sobre o impacto potencial da aplicação de uma ferramenta da produção enxuta, o Mapeamento do Fluxo de Valor, na capacidade de fornecimento destas. Foram analisadas sete empresas no Estado. O resultado obtido foi uma redução geral nos tempos de estoques de 23%, o mesmo ocorrendo para o tempo de agregação de valor, reduzido em 65%. Pode-se dizer, portanto, que os ganhos potenciais com a aplicação das propostas apresentadas possibilitariam às empresas não somente fornecer de acordo com a demanda do cliente e em fluxo contínuo, mas também aumentar sua capacidade de fornecimento, atendendo às exigências de preço, prazo e flexibilidade.The automotive industry, especially in the 90's, has been passed through a re-structure process of its productive base and supply relationship. Supporting such a process, there is a production philosophy coined lean production. This paper aims at pointing out some considerations about what could be done, regarding the production process, that may improve the supply capability of the autoparts firms in the RS state. Seven firms were analyzed and a lean production tool, the Value Stream Mapping, was applied. The results obtained were positive in all firms. The general stock reductions were of about 23%. Concerning value addition the reductions were of about 65%. Therefore, the potential gains from the implementation of the improvements suggested at Value Stream Map would make it possible not only to produce accordingly to the demand but also, to increase the supply capability of the firms.

  9. Lean years

    Energy Technology Data Exchange (ETDEWEB)

    Barnet, R J

    1982-01-01

    The author attempts to take stock of five critical systems of resources: Energy, mineral resources, food, water, and human abilities. All five systems have been integrated, to an ever-increasing extent in global control systems. These control systems determine how many people, in what parts of the world, will be faced with hunger, cold, or unemployment. The author tries to find out who is in charge of these control systems, how they have come into existence, and on what strategies they are based. In the final chapter, ''Policy of survival'', the author states that the secret of survival in the lean years to come is still in the dark. Man's most fundamental desire is to be human, i.e. to be in harmony with nature both psychologically and biologically. Politics should take account of this and provide us with the means for doing what is necessary.

  10. Internal lean practitioner's challenges in lean principles ...

    African Journals Online (AJOL)

    The approach to this paper is to answer the questions such as “how does internal management commitment impact the Lean principles?”, “how does Supply Chain Management practices impact the lean principles?”, “can Supply Chain Management practices be embedded with internal management commitment?

  11. Implementation of lean leadership

    Directory of Open Access Journals (Sweden)

    Trenkner Małgorzata

    2016-12-01

    Full Text Available The Toyota case proves that lean leadership is of critical importance for the successful implementation and permanent functioning of Lean Production System. There is no ready formula for developing Toyota style lean leadership. However, one may gain inspiration from its experience.

  12. Lean information management

    NARCIS (Netherlands)

    Hammer, D.K.

    1997-01-01

    The concept of a Lean Enterprise has proven to be extremely valuable for making companies fit for today's competitive business environment. Lean Information Management denotes the type of information management that is appropriate for such all organization. According to the paradigm of a Lean

  13. Simulation of lean premixed turbulent combustion

    International Nuclear Information System (INIS)

    Bell, J; Day, M; Almgren, A; Lijewski, M; Rendleman, C; Cheng, R; Shepherd, I

    2006-01-01

    There is considerable technological interest in developing new fuel-flexible combustion systems that can burn fuels such as hydrogen or syngas. Lean premixed systems have the potential to burn these types of fuels with high efficiency and low NOx emissions due to reduced burnt gas temperatures. Although traditional Scientific approaches based on theory and laboratory experiment have played essential roles in developing our current understanding of premixed combustion, they are unable to meet the challenges of designing fuel-flexible lean premixed combustion devices. Computation, with its ability to deal with complexity and its unlimited access to data, has the potential for addressing these challenges. Realizing this potential requires the ability to perform high fidelity simulations of turbulent lean premixed flames under realistic conditions. In this paper, we examine the specialized mathematical structure of these combustion problems and discuss simulation approaches that exploit this structure. Using these ideas we can dramatically reduce computational cost, making it possible to perform high-fidelity simulations of realistic flames. We illustrate this methodology by considering ultra-lean hydrogen flames and discuss how this type of simulation is changing the way researchers study combustion

  14. Performance effect of Lean

    DEFF Research Database (Denmark)

    Kristensen, Thomas Borup; Israelsen, Poul

    2016-01-01

    To understand how the practices of Lean affect performance, we tested and validated a system-wide approach using mediating relationships in a structural equation model. We used a cross-sectional survey of 200 Danish companies that indicated that they used Lean. Thus, this study is especially...... relevant to Denmark, but the approach is empirically more generalizable. We show that the effect of Lean standardized flow production practices on performance is mediated by analytical continuous improvement empowerment practices and by delegation of decision rights practices. Thus, standardized flow...... of decision rights. The paper provides evidence that supports the view that middle managers’ actions further enhance performance in Lean companies. The right Lean behavior by middle managers increases the level of analytical continuous improvement empowerment. In total, high-performing Lean companies...

  15. LEAN dig ikke tilbage

    DEFF Research Database (Denmark)

    Weirsøe, Mathilde

    2011-01-01

    Fit, slankere, hurtigst. Lean-konceptet ruller ind over de offentlige institutioner, hvor det skal trimme og effektivisere arbejdsprocesser. Men hvor er den maksimale grænse for effektivitet? Er der et ’tipping point’, hvor Lean ikke længere motiverer, men snarere udmatter......Fit, slankere, hurtigst. Lean-konceptet ruller ind over de offentlige institutioner, hvor det skal trimme og effektivisere arbejdsprocesser. Men hvor er den maksimale grænse for effektivitet? Er der et ’tipping point’, hvor Lean ikke længere motiverer, men snarere udmatter...

  16. Industry 4.0 implies lean manufacturing: Research activities in industry 4.0 function as enablers for lean manufacturing

    Directory of Open Access Journals (Sweden)

    Adam Sanders

    2016-09-01

    Full Text Available Purpose: Lean Manufacturing is widely regarded as a potential methodology to improve productivity and decrease costs in manufacturing organisations. The success of lean manufacturing demands consistent and conscious efforts from the organisation, and has to overcome several hindrances. Industry 4.0 makes a factory smart by applying advanced information and communication systems and future-oriented technologies. This paper analyses the incompletely perceived link between Industry 4.0 and lean manufacturing, and investigates whether Industry 4.0 is capable of implementing lean. Executing Industry 4.0 is a cost-intensive operation, and is met with reluctance from several manufacturers. This research also provides an important insight into manufacturers’ dilemma as to whether they can commit into Industry 4.0, considering the investment required and unperceived benefits. Design/methodology/approach: Lean manufacturing is first defined and different dimensions of lean are presented. Then Industry 4.0 is defined followed by representing its current status in Germany. The barriers for implementation of lean are analysed from the perspective of integration of resources. Literatures associated with Industry 4.0 are studied and suitable solution principles are identified to solve the abovementioned barriers of implementing lean. Findings: It is identified that researches and publications in the field of Industry 4.0 held answers to overcome the barriers of implementation of lean manufacturing. These potential solution principles prove the hypothesis that Industry 4.0 is indeed capable of implementing lean. It uncovers the fact that committing into Industry 4.0 makes a factory lean besides being smart. Originality/value: Individual researches have been done in various technologies allied with Industry 4.0, but the potential to execute lean manufacturing was not completely perceived. This paper bridges the gap between these two realms, and identifies

  17. Lean Production : Werkzeuge zur Realisierung

    OpenAIRE

    Binner, Hartmut F.

    2008-01-01

    INHALT: l. Einleitung und Standortbestimmung 2. Japanische Wertvorstellungen 3. Inhalte der Lean Production 4. Fertigungssegmentierung 5. Informationsmanagement mit CIM- und Logistik-Komponenten 6. Logistikgerechte Strukturen der Lean Production 7. Realisierung der Lean Production 8. Zusammenfassung

  18. Lean and Information Technology Toolkit

    Science.gov (United States)

    The Lean and Information Technology Toolkit is a how-to guide which provides resources to environmental agencies to help them use Lean Startup, Lean process improvement, and Agile tools to streamline and automate processes.

  19. Moving on - beyond lean thinking

    OpenAIRE

    Koskela, Lauri

    2004-01-01

    Lean Thinking is currently often positioned as the underlying theory of lean production among practitioners and academics, although its originators, Womack and Jones, seem not to have presented it as a theory. This paper endeavors to analyze whether Lean Thinking can be viewed as a theory of lean production. For this purpose, a critical assessment of Lean Thinking is carried out. Lean Thinking is argued to lack an adequate conceptualization of production, which has led to imprecise concepts, ...

  20. lean-ISD.

    Science.gov (United States)

    Wallace, Guy W.

    2001-01-01

    Explains lean instructional systems design/development (ISD) as it relates to curriculum architecture design, based on Japan's lean production system. Discusses performance-based systems; ISD models; processes for organizational training and development; curriculum architecture to support job performance; and modular curriculum development. (LRW)

  1. Healthy Lean Through HRD

    DEFF Research Database (Denmark)

    Jørgensen, Frances

    2008-01-01

    The paper reports on findings from the initial, exploratory phase of a longitudinal research study aimed at developing a framework for implementing lean while ensuring employee well-being. Data from observations and in-depth dialogues with persons involved in lean implementation, along...

  2. LEAN and energy efficiency; Lean og energieffektivisering

    Energy Technology Data Exchange (ETDEWEB)

    Jespersen, Per T; Vesterager Christensen, D; Andersen, Hans [Teknologisk Institut, Energi og Klima, Taastrup (Denmark); Dam Wied, M; Dam, M [NRGi Raadgivning, Aarhus (Denmark); Thorndahl, M [Horsens Kommune, Horsens (Denmark); Weldingh, P [Lokal Energi, Viby J. (Denmark); Maagoee, P; Kristensen, Kenneth T [Viegand og Maagoee, Copenhagen (Denmark); Kirketerp Friis, A [Novozymes, Bagsvaerd (Denmark)

    2010-03-15

    By means of theoretical reports and three specific cases, the project showed how Lean principles can improve energy consulting efficiency, thus making it easier for end-users and energy consultants to record and document energy savings achieved. The three cases documented various types of extra benefits of integrating energy efficiency improvement in Lean processes. As a result of process optimisation, one manufacturing company successfully reduced both staffing and energy consumption, thus making production in Denmark competitive with out-sourced production in Asia. (LN)

  3. Quality improvement in basic histotechnology: the lean approach.

    Science.gov (United States)

    Clark, David

    2016-01-01

    Lean is a comprehensive system of management based on the Toyota production system (TPS), encompassing all the activities of an organization. It focuses management activity on creating value for the end-user by continuously improving operational effectiveness and removing waste. Lean management creates a culture of continuous quality improvement with a strong emphasis on developing the problem-solving capability of staff using the scientific method (Deming's Plan, Do, Check, Act cycle). Lean management systems have been adopted by a number of histopathology departments throughout the world to simultaneously improve quality (reducing errors and shortening turnround times) and lower costs (by increasing efficiency). This article describes the key concepts that make up a lean management system, and how these concepts have been adapted from manufacturing industry and applied to histopathology using a case study of lean implementation and evidence from the literature. It discusses the benefits, limitations, and pitfalls encountered when implementing lean management systems.

  4. Adiabatic burning velocity of H2-O2 mixtures diluted with CO2/N2/Ar

    International Nuclear Information System (INIS)

    Ratna Kishore, V.; Muchahary, Ringkhang; Ray, Anjan; Ravi, M.R.

    2009-01-01

    Global warming due to CO 2 emissions has led to the projection of hydrogen as an important fuel for future. A lot of research has been going on to design combustion appliances for hydrogen as fuel. This has necessitated fundamental research on combustion characteristics of hydrogen fuel. In this work, a combination of experiments and computational simulations was employed to study the effects of diluents (CO 2 , N 2 , and Ar) on the laminar burning velocity of premixed hydrogen/oxygen flames using the heat flux method. The experiments were conducted to measure laminar burning velocity for a range of equivalence ratios at atmospheric pressure and temperature (300 K) with reactant mixtures containing varying concentrations of CO 2 , N 2 , and Ar as diluents. Measured burning velocities were compared with computed results obtained from one-dimensional laminar premixed flame code PREMIX with detailed chemical kinetics and good agreement was obtained. The effectiveness of diluents in reduction of laminar burning velocity for a given diluent concentration is in the increasing order of argon, nitrogen, carbon dioxide. This may be due to increased capabilities either to quench the reaction zone by increased specific heat or due to reduced transport rates. The lean and stoichiometric H 2 /O 2 /CO 2 flames with 65% CO 2 dilution exhibited cellular flame structures. Detailed three-dimensional simulation was performed to understand lean H 2 /O 2 /CO 2 cellular flame structure and cell count from computed flame matched well with the experimental cellular flame. (author)

  5. Potentiel des moteurs à mélange pauvre face aux moteurs actuels à réglage stoechiométrique : consommation, émissions, exigence en octane The Challenge to Modern Stoichiometric Engines by the Potential Lean-Burn Engine: Consumption, Emissions, Fuel Requirements

    Directory of Open Access Journals (Sweden)

    Douaud A. M.

    2006-11-01

    Full Text Available Le moteur à allumage commandé pour application automobile aux États-Unis est généralement dépollué par catalyse trifonctionnelle qui impose un contrôle stoechiométrique du mélange air-carburant. Le contexte européen de 1990 pour la qualité de l'air stimule l'industrie automobile dans ses recherches de solutions techniques performantes. Le moteur à mélange pauvre, performant en consommation, est une solution potentielle si l'émission de NOx peut être maîtrisée par la combustion. Cet objectif nécessite une conception du moteur contrôlant la turbulence et l'hétérogénéité du mélange air + carburant + résiduels pendant la combustion. La longévité de l'adaptation optimale moteur-carburant nécessitera un contrôle électronique de l'allumage et l'utilisation d'additifs détergents. Pour satisfaire les réglementations les plus sévères, les émissions de CO et HC pourront être contrôlées par un simple pot catalytique d'oxydation. Des oxydes de métaux non précieux introduits dans la formule catalytique en addition aux métaux précieux maintiennent la fonction oxydante pendant les transitoires en mélange riche tout en réduisant partiellement les NOx. Une vue d'ensemble de ce concept basé sur des simulations numériques et des résultats expérimentaux de consommation, d'émission, d'exigence en octane, etc. est présentée. Spark-ignition engines for automotive applications in the United States are currently depolluted by a 3-way catalyst that requires air-fuel control at stoichiometry. The 1990 European context for air pollution control is stimulating the automotive industry to search for improved technical solutions. The lean-burn engine is a potential fuel-efficient answer if its combustion can be optimized for low NOx emissions. Achieving this challenging approach requires engine design to control the turbulence and heterogeneity of the air + fuel + residual mixture during combustion. Electronic ignition

  6. Diccionario Lean Manufacturing

    OpenAIRE

    Muñoz Ellner, Sarah María

    2016-01-01

    El Diccionario Bilingüe de Lean Manufacturing pretende ser un instrumento de apoyo a todo aquel que tenga la responsabilidad de planear, ejecutar o simplemente algún interés con las actividades de Lean Manufacturing, aportando así también conceptos claros tanto en castellano como en inglés, con el fin de entender de forma integral el alcance mismo que puede llegar a tener dicha filosofía, al igual que se proporcionara una serie de siglas y herramientas para la implementación del Lean Manufact...

  7. Lean og arbejdsmiljø

    DEFF Research Database (Denmark)

    Jensen, Kenneth

    Bogen tager udgangspunkt i en undersøgelse af 10 private og offentlige virksomheders erfaringer med lean. Undersøgelsen viser at der ikke findes entydige sammenhænge mellem lean og det psykosociale arbejdsmiljø. Bogen forholder sig til sammenhængen mellem lean og ledelse, lean og medarbejderens...... rolle, lean og lean og forandringsprocessen. Bogen kommer desuden med anbefalinger til hvorledes virksomheden kan gribe dialogen an for at opnå et godt lean forløb der inddrager hensynet til og effekterne af et godt psykosocialt arbejdsmiljø....

  8. Exploring the Development of Competence in Lean Management through Action Learning Groups: A Study of the Introduction of Lean to a Facilities Management Function

    Science.gov (United States)

    Wyton, Paul; Payne, Robin

    2014-01-01

    The introduction of a Lean approach to management requires the development of understanding and capability. This in turn requires a structured training intervention and other supporting activities. This paper explores, through a case study, the way in which action learning groups (ALGs) supported the development of Lean capabilities in the…

  9. Orchestrating Lean Implementation

    DEFF Research Database (Denmark)

    Riis, Jens Ove; Mikkelsen, Hans; Andersen, Jesper Rank

    2008-01-01

    The notion of Lean Manufacturing is not merely confined to a set of well defined techniques, but represents a broad approach to managing a company. Working with lean entails many aspects, such as production planning and control, production engineering, product development, supply chain......, and organizational issues. To become effective, many functional areas and departments must be involved. At the same time companies are embedded in a dynamic environment. The aim of the paper is to propose a comprehensive approach to better implementation of lean initiatives, based on two empirical studies. The paper...... will discuss how a concerted effort can be staged taking into account the interdependencies among individual improvement initiatives. The notion of orchestration will be introduced, and several means for orchestration will be presented. Critical behavioral issues for lean implementation will be discussed....

  10. Lean Government Methods Guide

    Science.gov (United States)

    This Guide focuses primarily on Lean production, which is an organizational improvement philosophy and set of methods that originated in manufacturing but has been expanded to government and service sectors.

  11. Lean Enterprise Value Phase

    National Research Council Canada - National Science Library

    Shields, John T

    2005-01-01

    ... using a philosophy called "lean." LAl's mission is to research, develop, and promulgate practices, tools, and knowledge that enable and accelerate the envisioned transformation of the greater US aerospace enterprise through people and processes...

  12. The lean service machine.

    Science.gov (United States)

    Swank, Cynthia Karen

    2003-10-01

    Jefferson Pilot Financial, a life insurance and annuities firm, like many U.S. service companies at the end of the 1990s was looking for new ways to grow. Its top managers recognized that JPF needed to differentiate itself in the eyes of its customers, the independent life-insurance advisers who sell and service policies. To establish itself as these advisers' preferred partner, it set out to reduce the turnaround time on policy applications, simplify the submission process, and reduce errors. JPF's managers looked to the "lean production" practices that U.S. manufacturers adopted in response to competition from Japanese companies. Lean production is built around the concept of continuous-flow processing--a departure from traditional production systems, in which large batches are processed at each step. JPF appointed a "lean team" to reengineer its New Business unit's operations, beginning with the creation of a "model cell"--a fully functioning microcosm of JPF's entire process. This approach allowed managers to experiment and smooth out the kinks while working toward an optimal design. The team applied lean-manufacturing practices, including placing linked processes near one another, balancing employees' workloads, posting performance results, and measuring performance and productivity from the customer's perspective. Customer-focused metrics helped erode the employees' "My work is all that matters" mind-set. The results were so impressive that JPF is rolling out similar systems across many of its operations. To convince employees of the value of lean production, the lean team introduced a simulation in which teams compete to build the best paper airplane based on invented customer specifications. This game drives home lean production's basic principles, establishing a foundation for deep and far-reaching changes in the production system.

  13. EPA Lean Government Initiative: How to Replicate Lean Successes

    Science.gov (United States)

    This Lean Replication Primer describes how EPA Offices and Regions can identify and adapt successful practices from previous Lean projects to “replicate” their successes and generate further improvements.

  14. Can lean save lives?

    Science.gov (United States)

    Fillingham, David

    2007-01-01

    The purpose of this paper is to show how over the last 18 months Bolton Hospitals NHS Trust have been exploring whether or not lean methodologies, often known as the Toyota Production System, can indeed be applied to healthcare. This paper is a viewpoint. One's early experience is that lean really can save lives. The Toyota Production System is an amazingly successful way of manufacturing cars. It cannot be simply translated unthinkingly into a hospital but lessons can be learned from it and the method can be adapted and developed so that it becomes owned by healthcare staff and focused towards the goal of improved patient care. Working in healthcare is a stressful and difficult thing. Everyone needs a touch of inspiration and encouragement. Applying lean to healthcare in Bolton seems to be achieving just that for those who work there.

  15. Rethinking Lean Service

    Science.gov (United States)

    Seddon, John; O'Donovan, Brendan; Zokaei, Keivan

    Ever since Levitt's influential Harvard Business Review article 'Production-Line Approach to Service' was published in 1972, it has been common for services to be treated like production lines in both the academic literature and more widely in management practice. The belief that achieving economies of scale will reduce unit costs is a common feature of management decision-making. As technological advancement has produced ever more sophisticated IT and telephony, it has become increasingly easier for firms to standardise and off-shore services. The development of the 'lean' literature has only helped to emphasise the same underlying management assumptions: by managing cost and workers' activity, organisational performance is expected to improve. This chapter argues that through misinterpretation of the core paradigm 'lean' has become subsumed into the 'business as usual' of conventional service management. As a result, 'lean' has become synonymous with 'process efficiency' and the opportunity for significant performance improvement - as exemplified by Toyota - has been missed.

  16. Burn Wise

    Science.gov (United States)

    Burn Wise is a partnership program of the U.S. Environmental Protection Agency that emphasizes the importance of burning the right wood, the right way, in the right appliance to protect your home, health, and the air we breathe.

  17. An experimental investigation of a lean-burn natural-gas pre-chamber spark ignition engine for cogeneration; Swiss Motor. Modification d'un moteur diesel pour le fonctionnement au gaz naturel en cogeneration. Fonctionnement avec prechambre de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Roethlisberger, R.; Favrat, D.

    2001-07-01

    This thesis presented at the Department of Mechanical Engineering of the Swiss Federal Institute of Technology in Lausanne describes the conversion and testing of a commercial diesel engine for use as a lean-burn, natural gas, pre-chamber, spark ignition engine with a rated power of 150 kW, in combined heat and power (CHP) plants. The objective of the investigations - to evaluate the potential of reducing exhaust gas emissions - is discussed in detail with respect to NO{sub x} and CO emissions. The approach adopted includes both experimental work and numerical simulation. The report describes the testing facilities used. The results obtained with experimental spark-plug configurations based on simulation results are presented and the influence of various pre-chamber configuration variants are discussed. The results of the tests are presented and the significant reduction of NO{sub x}, CO and unburned-hydrocarbon (THC) emissions are discussed. The authors state that the engine, which achieves a fuel efficiency of more than 36.5%, fulfils the Swiss requirements on exhaust gas emissions. Also, ways of compensating for the slight loss in fuel-conversion efficiency in the pre-chamber configuration are discussed.

  18. Lean Management Genesis

    Directory of Open Access Journals (Sweden)

    Parkes Aneta

    2015-12-01

    Full Text Available Lean Management is a philosophy and management concept, based on reduction of the waste and resources used in the process of producing goods and providing services. Lean Management genesis dates back to scientific management in America (for example concepts of H. Ford and F.W. Taylor and quality management, including development of TQM concept. Japanese Toyota Production System has been inspired by chosen elements of these concepts, and then it evolved towards global concept called Toyota Way (which connects production rules with values and work attitude.

  19. Improving Healthcare through Lean Management

    DEFF Research Database (Denmark)

    Nielsen, Anders Paarup; Edwards, Kasper

    2011-01-01

    The ideas and principles from lean management are now widely being adopted within the healthcare sector. The analysis in this paper shows that organizations within healthcare most often only implement a limited set of tools and methods from the lean tool-box. Departing from a theoretical analysis...... of the well-known and universal lean management principles in the context of the healthcare this paper will attempt to formulate and test four hypotheses about possible barriers to the successful implementation of lean management in healthcare. The first hypothesis states that lean management in healthcare....... The paper concludes by discussing the implications of hypothesis two, three, and four for the successful application of lean management within healthcare. Is it concluded that this requires a transformative and contingent approach to lean management where the universal principles of the lean philosophy...

  20. Lean in Air Permitting Guide

    Science.gov (United States)

    The Lean in Air Permitting Guide is designed to help air program managers at public agencies better understand the potential value and results that can be achieved by applying Lean improvement methods to air permitting processes.

  1. The Lean and Environment Toolkit

    Science.gov (United States)

    This Lean and Environment Toolkit assembles practical experience collected by the U.S. Environmental Protection Agency (EPA) and partner companies and organizations that have experience with coordinating Lean implementation and environmental management.

  2. Ghrelin receptor controls obesity by fat burning

    Science.gov (United States)

    Emerging evidence show that brown fat in the body produces heat to burn energy, thus prompting weight loss. Ghrelin is the only known hormone which increases appetite and promotes weight gain. We have reported that mice that lack the receptor which mediates the functions of ghrelin are lean. Our fu...

  3. Lean leadership: an ethnographic study

    NARCIS (Netherlands)

    Aij, K.H.; Visse, M.A.; Widdershoven, G.A.M.

    2015-01-01

    Purpose – The purpose of this study is to provide a critical analysis of contemporary Lean leadership in the context of a healthcare practice. The Lean leadership model supports professionals with a leading rolein implementing Lean.This article presents a case study focusing specifcally on

  4. Lean With a Human Face

    DEFF Research Database (Denmark)

    Hasle, Peter; Jensen, Per Langaa

    2008-01-01

    The consequences for quality of work of lean manufacturing is discussed in the international litterature, and several authors suggest increased work speed, stress, and muscoskeletal diseases as a consequence of lean. The Danish experience with lean has been studied through interviews with managers...

  5. Design thinking & lean

    DEFF Research Database (Denmark)

    Bravos, Cynthia; Adler, Isabel K.

    2015-01-01

    This paper aims at presenting how a Brazilian innovation consultancy guided a collaborative development of a mobile solution using the Design Thinking approach (Vianna et al, 2012) and Lean principles (Ries, 2011). It will describe tools and methods used and how it was applied to requirement gath...

  6. Ares Launch Vehicles Lean Practices Case Study

    Science.gov (United States)

    Doreswamy, Rajiv; Self, Timothy A.

    2007-01-01

    The Ares launch vehicles team, managed by the Ares Projects Office (APO) at NASA Marshall Space Flight Center, has completed the Ares I Crew Launch Vehicle System Requirements Review and System Definition Review and early design work for the Ares V Cargo Launch Vehicle. This paper provides examples of how Lean Manufacturing, Kaizen events, and Six Sigma practices are helping APO deliver a new space transportation capability on time and within budget, while still meeting stringent technical requirements. For example, Lean philosophies have been applied to numerous process definition efforts and existing process improvement activities, including the Ares I-X test flight Certificate of Flight Readiness (CoFR) process, risk management process, and review board organization and processes. Ares executives learned Lean practices firsthand, making the team "smart buyers" during proposal reviews and instilling the team with a sense of what is meant by "value-added" activities. Since the goal of the APO is to field launch vehicles at a reasonable cost and on an ambitious schedule, adopting Lean philosophies and practices will be crucial to the Ares Project's long-term SUCCESS.

  7. Lean mixture engine testing and evaluation program. [for automobile engine pollution and fuel performances

    Science.gov (United States)

    Dowdy, M. W.; Hoehn, F. W.; Griffin, D. C.

    1975-01-01

    Experimental results for fuel consumption and emissions are presented for a 350 CID (5.7 liter) Chevrolet V-8 engine modified for lean operation with gasoline. The lean burn engine achieved peak thermal efficiency at an equivalence ratio of 0.75 and a spark advance of 60 deg BTDC. At this condition the lean burn engine demonstrated a 10% reduction in brake specific fuel consumption compared with the stock engine; however, NOx and hydrocarbon emissions were higher. With the use of spark retard and/or slightly lower equivalence ratios, the NOx emissions performance of the stock engine was matched while showing a 6% reduction in brake specific fuel consumption. Hydrocarbon emissions exceeded the stock values in all cases. Diagnostic data indicate that lean performance in the engine configuration tested is limited by ignition delay, cycle-to-cycle pressure variations, and cylinder-to-cylinder distribution.

  8. Lean start-up

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2016-01-01

    The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The ma...... and the final business model. In other words: The start-up must first nail the problem together with the customers, then develop the solution and test, and then in the end scale it to a full-grown business model.......The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

  9. Green and lean management

    CERN Document Server

    Davim, J

    2017-01-01

    This book focusses on the challenges and changes organizational management faces in an era when the need to develop environmentally aware processes meets high levels of competition. It covers the synergetic effects, how re-use, recycling, waste reduction, and other sustainable production strategies can add value, low costs and time of production. Sustainable business behavior is not only an environmental perspective on management, but more and more contains an organizational perspective. Taking into account these issues, green and lean management appears as the way managers can drive their employees to continuously improve the management processes that add value to the organization and costumers. This book provides information on principles, strategies, models, and applications of green and lean management, and at the same time communicates the latest research activity relating to this scientific field world-wide.

  10. Lean Leadership - Organizational Buy - Ins

    Directory of Open Access Journals (Sweden)

    Dr. Revathi Iyer

    2017-05-01

    Full Text Available Great organizations have become leaders due to their leadership and sustainable initiatives. One such initiative is adoption of lean leadership to align core strategies with all functional areas of business. Leadership is likely to take place in a lean environment because improvements that happen are continual and can only be supported by leadership which understands this important aspect. The topic of lean leadership organizational buy ins speaks on how lean leadership could affect organizations that adopt lean and other quality tools. Purpose of the study This study has been undertaken to understand When leadership more of is likely to take place in lean . Leadership plays a very important role while adopting lean processes and how lean leadership can address the process problem. Application of leadership lenses to lean processes needs great foresight thought and creativity. It has been also observed that lean management and lean processes can happen only if leadership is able to effectively communicate the thought of continual improvement to bring in a lean organization and a future state of processes where everything of a firm process and procedure is continually improving and the best strategies to manage this change becomes a philosophy. Lean leadership is associated with such a change. This enables leadership vision to be clear as it paves the way for current state and is clear to everyone. It is this leadership vision which enables employees to think and act in a way that perpetrates continual improvement. Hence leadership buys ins for lean are very necessary. The purpose of the study is also to understand how leaders can not only use cost reduction but also reducing time-to-market improving service quality and reducing risk exposure by adopting lean methods . it has been also seen that there is overall productivity and efficiency in organizations holistically when leadership endorses lean methodology. Radnor Z. and Bucci G. 2007

  11. Lean leadership: an ethnographic study.

    Science.gov (United States)

    Aij, Kjeld Harald; Visse, Merel; Widdershoven, Guy A M

    2015-01-01

    The purpose of this study is to provide a critical analysis of contemporary Lean leadership in the context of a healthcare practice. The Lean leadership model supports professionals with a leading role in implementing Lean. This article presents a case study focusing specifically on leadership behaviours and issues that were experienced, observed and reported in a Dutch university medical centre. This ethnographic case study provides auto-ethnographic accounts based on experiences, participant observation, interviews and document analysis. Characteristics of Lean leadership were identified to establish an understanding of how to achieve successful Lean transformation. This study emphasizes the importance for Lean leaders to go to the gemba, to see the situation for one's own self, empower health-care employees and be modest. All of these are critical attributes in defining the Lean leadership mindset. In this case study, Lean leadership is specifically related to healthcare, but certain common leadership characteristics are relevant across all fields. This article shows the value of an auto-ethnographic view on management learning for the analysis of Lean leadership. The knowledge acquired through this research is based on the first author's experiences in fulfilling his role as a health-care leader. This may help the reader examining his/her own role and reflecting on what matters most in the field of Lean leadership.

  12. LEAN LABORATORY APPROACHES FOR QUALITY ASSURANCE IN FOOD

    Directory of Open Access Journals (Sweden)

    Laxmana Naik

    2011-09-01

    Full Text Available A lean laboratory is one which is focused on testing products and materials to deliver results in the most efficient way in terms of cost or speed or both; primarily focused on improving measurable performance and reducing costs. The goal of a lean laboratory is to use less effort, less resources and less time to test incoming samples. Laboratories have a critical role to play in establishing and improving process capability and key performance indicator (KPI of the organization. There are inevitably many opinions as to what a lean lab actually is; here is one version fr om. Quality assurance laboratories are crucial to the success of organization and this effectiveness needs to be measurable and demonstrable. To facilitate this, a method of measuring a laboratory's progress towards complete deployment has been created by lean tools. These tools allow laboratories to conduct gap analysis and identify opportunities for improvement.

  13. Numerical simulation of nitrogen oxide formation in lean premixed turbulent H2/O2/N2 flames

    DEFF Research Database (Denmark)

    Day, Marc S.; Bell, John B.; Gao, Xinfeng

    2011-01-01

    Lean premixed hydrogen flames are thermodiffusively unstable and burn in cellular structures. Within these cellular structures the flame is locally enriched by preferential diffusion of hydrogen, leading to local hotspots that burn more intensely than an idealized flat steady flame at comparable ...

  14. Organizational change through Lean Thinking.

    Science.gov (United States)

    Tsasis, Peter; Bruce-Barrett, Cindy

    2008-08-01

    In production and manufacturing plants, Lean Thinking has been used to improve processes by eliminating waste and thus enhancing efficiency. In health care, Lean Thinking has emerged as a comprehensive approach towards improving processes embedded in the diagnostic, treatment and care activities of health-care organizations with cost containment results. This paper provides a case study example where Lean Thinking is not only used to improve efficiency and cost containment, but also as an approach to effective organizational change.

  15. Applying lean thinking in construction

    Directory of Open Access Journals (Sweden)

    Remon Fayek Aziz

    2013-12-01

    Full Text Available The productivity of the construction industry worldwide has been declining over the past 40 years. One approach for improving the situation is using lean construction. Lean construction results from the application of a new form of production management to construction. Essential features of lean construction include a clear set of objectives for the delivery process, aimed at maximizing performance for the customer at the project level, concurrent design, construction, and the application of project control throughout the life cycle of the project from design to delivery. An increasing number of construction academics and professionals have been storming the ramparts of conventional construction management in an effort to deliver better value to owners while making real profits. As a result, lean-based tools have emerged and have been successfully applied to simple and complex construction projects. In general, lean construction projects are easier to manage, safer, completed sooner, and cost less and are of better quality. Significant research remains to complete the translation to construction of lean thinking in Egypt. This research will discuss principles, methods, and implementation phases of lean construction showing the waste in construction and how it could be minimized. The Last Planner System technique, which is an important application of the lean construction concepts and methodologies and is more prevalent, proved that it could enhance the construction management practices in various aspects. Also, it is intended to develop methodology for process evaluation and define areas for improvement based on lean approach principles.

  16. Lean software development in action

    CERN Document Server

    Janes, Andrea

    2014-01-01

    This book illustrates how goal-oriented, automated measurement can be used to create Lean organizations and to facilitate the development of Lean software, while also demonstrating the practical implementation of Lean software development by combining tried and trusted tools. In order to be successful, a Lean orientation of software development has to go hand in hand with a company's overall business strategy. To achieve this, two interrelated aspects require special attention: measurement and experience management. In this book, Janes and Succi provide the necessary knowledge to establish "

  17. First Lean, then modularisation

    DEFF Research Database (Denmark)

    Petersen, Kristian R.; Madsen, Erik Skov; Bilberg, Arne

    2016-01-01

    of Europe’s leading offshore wind power operators with more than 1,000 wind turbine generators in operation. By focusing on this company, in-depth insights into its operations and maintenance processes are investigated. Findings – Lean is identified to constitute an important first step before...... and resources can take place. The authors also establish a foundation for the development of a software tool to support the development of the modularisation of maintenance tasks. Originality/value – The present study contributes to the rather immature field of research on the operations and maintenance...

  18. Lean approach in knowledge work

    Directory of Open Access Journals (Sweden)

    Hanna Kropsu-Vehkapera

    2018-05-01

    Full Text Available Purpose: Knowledge work productivity is a key area of improvement for many organisations. Lean approach is a sustainable way to achieve operational excellence and can be applied in many areas. The purpose of this novel study is to examine the potential of using lean approach for improving knowledge work practices. Design/methodology/approach: A systematic literature review has been carried out to study how lean approach is realised in knowledge work. The research is conceptual in nature and draws upon earlier research findings. Findings: This study shows that lean studies’ in knowledge work is an emerging research area. This study documents the methods and practices implemented in knowledge work to date, and presents a knowledge work continuum, which is an essential framework for effective lean approach deployment and to frame future research focus in knowledge work productivity. Research limitations/implications: This study structures the concept of knowledge work and outlines a concrete concept derived from earlier literature. The study summarises the literature on lean in knowledge work and highlights, which methods are used. More research is needed to understand how lean can be implemented in complex knowledge work environment and not only on the repetitive knowledge work. The limitations of this research are due to the limited availability of previous research. Practical implications: To analyse the nature of knowledge work, we implicate the areas where lean methods especially apply to improving knowledge work productivity. When applying lean in knowledge work context the focus should be using the people better and improving information flow. Originality/value: This study focuses on adapting lean methods into a knowledge work context and summarises earlier research done in this field. The study discusses the potential to improve knowledge work productivity by implementing lean methods and presents a unique knowledge work continuum to

  19. Ares Launch Vehicles Lean Practices Case Study

    Science.gov (United States)

    Doreswamy, Rajiv, N.; Self, Timothy A.

    2008-01-01

    This viewgraph presentation describes test strategies and lean philisophies and practices that are applied to Ares Launch Vehicles. The topics include: 1) Testing strategy; 2) Lean Practices in Ares I-X; 3) Lean Practices Applied to Ares I-X Schedule; 4) Lean Event Results; 5) Lean, Six Sigma, and Kaizen Practices in the Ares Projects Office; 6) Lean and Kaizen Success Stories; and 7) Ares Six Sigma Practices.

  20. LEAN thinking in Finnish healthcare.

    Science.gov (United States)

    Jorma, Tapani; Tiirinki, Hanna; Bloigu, Risto; Turkki, Leena

    2016-01-01

    Purpose - The purpose of this study is to evaluate how LEAN thinking is used as a management and development tool in the Finnish public healthcare system and what kind of outcomes have been achieved or expected by using it. The main focus is in managing and developing patient and treatment processes. Design/methodology/approach - A mixed-method approach incorporating the Webropol survey was used. Findings - LEAN is quite a new concept in Finnish public healthcare. It is mainly used as a development tool to seek financial savings and to improve the efficiency of patient processes, but has not yet been deeply implemented. However, the experiences from LEAN initiatives have been positive, and the methodology is already quite well-known. It can be concluded that, because of positive experiences from LEAN, the environment in Finnish healthcare is ready for the deeper implementation of LEAN. Originality/value - This paper evaluates the usage of LEAN thinking for the first time in the public healthcare system of Finland as a development tool and a management system. It highlights the implementation and achieved results of LEAN thinking when used in the healthcare environment. It also highlights the expectations for LEAN thinking in Finnish public healthcare.

  1. NASA GRC's High Pressure Burner Rig Facility and Materials Test Capabilities

    Science.gov (United States)

    Robinson, R. Craig

    1999-01-01

    The High Pressure Burner Rig (HPBR) at NASA Glenn Research Center is a high-velocity. pressurized combustion test rig used for high-temperature environmental durability studies of advanced materials and components. The facility burns jet fuel and air in controlled ratios, simulating combustion gas chemistries and temperatures that are realistic to those in gas turbine engines. In addition, the test section is capable of simulating the pressures and gas velocities representative of today's aircraft. The HPBR provides a relatively inexpensive. yet sophisticated means for researchers to study the high-temperature oxidation of advanced materials. The facility has the unique capability of operating under both fuel-lean and fuel-rich gas mixtures. using a fume incinerator to eliminate any harmful byproduct emissions (CO, H2S) of rich-burn operation. Test samples are easily accessible for ongoing inspection and documentation of weight change, thickness, cracking, and other metrics. Temperature measurement is available in the form of both thermocouples and optical pyrometery. and the facility is equipped with quartz windows for observation and video taping. Operating conditions include: (1) 1.0 kg/sec (2.0 lbm/sec) combustion and secondary cooling airflow capability: (2) Equivalence ratios of 0.5- 1.0 (lean) to 1.5-2.0 (rich), with typically 10% H2O vapor pressure: (3) Gas temperatures ranging 700-1650 C (1300-3000 F): (4) Test pressures ranging 4-12 atmospheres: (5) Gas flow velocities ranging 10-30 m/s (50-100) ft/sec.: and (6) Cyclic and steady-state exposure capabilities. The facility has historically been used to test coupon-size materials. including metals and ceramics. However complex-shaped components have also been tested including cylinders, airfoils, and film-cooled end walls. The facility has also been used to develop thin-film temperature measurement sensors.

  2. Burning Feet

    Science.gov (United States)

    ... be accompanied by a pins and needles sensation (paresthesia) or numbness, or both. Burning feet may also be referred to as tingling feet or paresthesia. While fatigue or a skin infection can cause ...

  3. Systematic model for lean product development implementation in an automotive related company

    Directory of Open Access Journals (Sweden)

    Daniel Osezua Aikhuele

    2017-07-01

    Full Text Available Lean product development is a major innovative business strategy that employs sets of practices to achieve an efficient, innovative and a sustainable product development. Despite the many benefits and high hopes in the lean strategy, many companies are still struggling, and unable to either achieve or sustain substantial positive results with their lean implementation efforts. However, as the first step towards addressing this issue, this paper seeks to propose a systematic model that considers the administrative and implementation limitations of lean thinking practices in the product development process. The model which is based on the integration of fuzzy Shannon’s entropy and Modified Technique for Order Preference by Similarity to the Ideal Solution (M-TOPSIS model for the lean product development practices implementation with respective to different criteria including management and leadership, financial capabilities, skills and expertise and organization culture, provides a guide or roadmap for product development managers on the lean implementation route.

  4. Burning issues

    International Nuclear Information System (INIS)

    Raloff, J.

    1993-01-01

    The idea of burning oil slicks at sea has intrigued oil-cleanup managers for more than a decade, but it wasn't until the advent of fireproof booms in the mid-1980's and a major spill opportunity (the March 1989 Exxon Valdez) that in-situ burning got a real sea trial. The results of this and other burning experiments indicate that, when conditions allow it, nothing can compete with fire's ability to remove oil from water. Burns have the potential to remove as much oil in one day as mechanical devices can in one month, along with minimal equipment, labor and cost. Reluctance to burn in appropriate situations comes primarily from the formation of oily, black smoke. Analysis of the potentially toxic gases have been done, indicating that burning will not increase the levels of polluting aldehydes, ketones, dioxins, furans, and PAHs above those that normally evaporate from spilled oil. This article contains descriptions of planned oil fires and the discussion on the advantages and concerns of such a policy

  5. Lean management beyond manufacturing a holistic approach

    CERN Document Server

    Bhasin, Sanjay

    2015-01-01

    Exploring Lean manufacturing in a holistic manner, this book helps organizations to implement Lean principles successfully by offering theoretical, empirical and practical knowledge. It empirically demonstrates how a successful Lean initiative can improve organizational efficiency, and incorporates valuable primary research to substantiate findings. It argues that Lean principles need to be applied throughout the value chain in order to be successful , and suggests that these tools need to be aligned with culture and change management. Chapters examine issues including Lean cultures, impediments to Lean, Lean and performance measurement, and the impact of Lean. Viewing Lean as a never-ending journey, this book provides a valuable resource to practising Lean managers, and specialist researchers and students, and also offers an important reference for organizations embarking on their Lean voyage.

  6. Capability Paternalism

    NARCIS (Netherlands)

    Claassen, R.J.G.|info:eu-repo/dai/nl/269266224

    A capability approach prescribes paternalist government actions to the extent that it requires the promotion of specific functionings, instead of the corresponding capabilities. Capability theorists have argued that their theories do not have much of these paternalist implications, since promoting

  7. Load compensation in a lean burn natural gas vehicle

    Science.gov (United States)

    Gangopadhyay, Anupam

    A new multivariable PI tuning technique is developed in this research that is primarily developed for regulation purposes. Design guidelines are developed based on closed-loop stability. The new multivariable design is applied in a natural gas vehicle to combine idle and A/F ratio control loops. This results in better recovery during low idle operation of a vehicle under external step torques. A powertrain model of a natural gas engine is developed and validated for steady-state and transient operation. The nonlinear model has three states: engine speed, intake manifold pressure and fuel fraction in the intake manifold. The model includes the effect of fuel partial pressure in the intake manifold filling and emptying dynamics. Due to the inclusion of fuel fraction as a state, fuel flow rate into the cylinders is also accurately modeled. A linear system identification is performed on the nonlinear model. The linear model structure is predicted analytically from the nonlinear model and the coefficients of the predicted transfer function are shown to be functions of key physical parameters in the plant. Simulations of linear system and model parameter identification is shown to converge to the predicted values of the model coefficients. The multivariable controller developed in this research could be designed in an algebraic fashion once the plant model is known. It is thus possible to implement the multivariable PI design in an adaptive fashion combining the controller with identified plant model on-line. This will result in a self-tuning regulator (STR) type controller where the underlying design criteria is the multivariable tuning technique designed in this research.

  8. Lean Startup and Lean Canvas Using for Innovative Product Development

    Directory of Open Access Journals (Sweden)

    Alena Buchalcevová

    2016-06-01

    Full Text Available Recently, new approaches to product development have emerged that focus on idea generation techniques and customer itself. One of them is the Lean Startup method that is described in this article along with the Lean Canvas method. The main goal of the article is to demonstrate the application of both methods to an innovative product development focused on providing interactive trips for families with children. The development of the product during individual phases is described and application of the Lean Startup and Lean Canvas principles is demonstrated. Finally, benefits of both methods contributing to the product success are discussed. Similar case studies start emerging worldwide, however in the Czech context are quite rare.

  9. Clinically lean; "cutting the crap".

    Science.gov (United States)

    Caldwell, G

    2012-01-01

    Proponents of Lean Philosophy believe that successful businesses must reduce waste in working time and resources to a minimum, and maximise their use in productive work. The productive work of the Acute Medical Unit is to provide effective clinical management to a daily cohort of acutely ill patients. Many Clinicians are cynical about Lean. In this article, Dr Caldwell discusses how many clinicians complain of too much crap in the workplace, which gets in the way of swift, safe high quality clinical care. He argues that "Cutting the Crap" in the Acute Medical Unit is entirely consistent with Lean approaches to management of complex systems.

  10. Improving healthcare using Lean processes.

    Science.gov (United States)

    Baker, G Ross

    2014-01-01

    For more than a decade, healthcare organizations across Canada have been using Lean management tools to improve care processes, reduce preventable adverse events, increase patient satisfaction and create better work environments. The largest system-wide effort in Canada, and perhaps anywhere, is currently under way in Saskatchewan. The jury is still out on whether Lean efforts in that province, or elsewhere in Canada, are robust enough to transform current delivery systems and sustain new levels of performance. This issue of Healthcare Quarterly features several articles that provide a perspective on Lean methods in healthcare. Copyright © 2014 Longwoods Publishing.

  11. Lean Manufacturing measurement: The relationships between Lean activities and Lean metrics

    Directory of Open Access Journals (Sweden)

    Diego Fernando Manotas Duque

    2007-01-01

    Full Text Available Medición en Lean Manufacturing: Relaciones entre Actividades Lean y Métricas Lean Lean Manufacturing fue desarrollada por Toyota para satisfacer sus necesidades específicas en un mercado restringido y en tiempos de estrechez económica. Estos conceptos han sido estudiados y se ha comprobado su aplicabilidad en una amplia variedad de industrias. El objetivo de este artículo es el de integrar un conjunto de métricas que han sido propuestas por diferentes autores, de tal manera que sean consistentes con las etapas y elementos de implementaciones de Lean Manufacturing. Para lograrlo se presentan dos marcos de referencia para implementaciones Lean y los principales factores de éxito se utilizan como base para proponer métricas que identifiquen el avance en estos factores. Posteriormente se propone una tabla que cruza el impacto de las “Actividades Lean” sobre las métricas, postulando que muchos de los supuestos a priori sobre estos impactos deberían ser precisos. Finalmente se proponen algunas ideas para proyectos de investigación hacia el futuro y posibles extensiones de las aplicaciones propuestas aquí.

  12. Researching Lean: Methodological Implications of Loose Definitions

    Directory of Open Access Journals (Sweden)

    Mikael Brännmark

    2012-12-01

    Full Text Available Recently, Lean Production (Lean has become a prevailing management concept in Sweden. However, previous research seems to show that the Lean concept and the impact of Lean vary considerably between organizations. This paper illustrates some key methodological issues that need to be considered when researching loosely defined management concepts such as Lean. The paper is based on a review of the literature and five comparative Swedish cases studies. Our study indicates that Lean has changed over time and that operationalization and interpretations of the concept vary considerably. This study concludes that future Lean studies should include a thorough assessment of the Lean interventions, study settings, and in particular non-Lean factors mediating the outcomes of Lean-inspired change programs.

  13. Lean Design and Management for Manufactoring

    OpenAIRE

    NIU, Zhanwen

    2009-01-01

    Most enterprises inducting lean production were confined by the innate limitations of existing production systems, which make it difficult to fulfill lean production comprehensively. To solve this problem, the theory of lean design and management for the manufacturing enterprise lifecycle was proposed. First, the necessities of lean design were analyzed and its theoretical system was established; second, the principles, process, methods and tools for lean design was introduced. Techniques and...

  14. The evolution of Lean organizations

    OpenAIRE

    Serafinas, Dalius; Ruželė, Darius

    2014-01-01

    Remiantis evoliucijos tyrimų modeliais bei autorių sudarytu evoliucionuojančios organizacijos modeliu,straipsnyje analizuojama Lean vadybos metodologija ir tiriama, kaip evoliucionuoja ją įgyvendinančios Lietuvosgamybinės organizacijos. The purpose of this paper is to examine the evolution of Lean organizations.Design/methodology/approach: a conceptual literature on the evolution of species, organisms and organizations was reviewed and an original model (framework) of the evolution of orga...

  15. Buildings Lean Maintenance Implementation Model

    Science.gov (United States)

    Abreu, Antonio; Calado, João; Requeijo, José

    2016-11-01

    Nowadays, companies in global markets have to achieve high levels of performance and competitiveness to stay "alive".Within this assumption, the building maintenance cannot be done in a casual and improvised way due to the costs related. Starting with some discussion about lean management and building maintenance, this paper introduces a model to support the Lean Building Maintenance (LBM) approach. Finally based on a real case study from a Portuguese company, the benefits, challenges and difficulties are presented and discussed.

  16. Lean Transformation of Multinational Concerns

    DEFF Research Database (Denmark)

    Matthiesen, Rikke Vestergaard; Johansen, John

    2008-01-01

    triggered. This paper reports on exploratory studies from a multinational company adopting centrally managed pilot projects as a transformation mechanism for continuous change towards a lean business system and an organizational culture of continuous improvements (CI). Competitive pressure demands...... from a multinational company adopting centrally managed pilot projects as a transformation mechanism for continuous change towards a lean business system and an organizational culture of continuous improvements (CI)....

  17. Wood burning

    Energy Technology Data Exchange (ETDEWEB)

    Winkelmann, H

    1955-01-01

    Discussed are the use of wood as a fuel, the technique of wood combustion and the operation of wood-burning stoves for cooking and heating. In addition, there is a section which reviews the use of wood stoves in various countries and lists manufacturers of stoves, central heating furnaces and in some cases sawdust burners.

  18. Performance of a hydrogen-enriched ethanol engine at unthrottled and lean conditions

    International Nuclear Information System (INIS)

    Zhang, Bo; Ji, Changwei; Wang, Shuofeng

    2016-01-01

    Highlights: • H_2 addition eased cyclic variation of ethanol engine at unthrottled condition. • H_2-blended ethanol engine gains better efficiency at lean conditions. • Bmep of H_2-blended ethanol engine could be controlled by lean burning. • H_2 addition results in reduced exhaust loss and HC emissions. - Abstract: Concerning the throttling loss under part load conditions, it is feasible to further improve the engine thermal efficiency through operating the engine under the unthrottled condition and controlling its load by changing the excess air ratio. However, the narrow flammability of ethanol may lead the ethanol engine to encounter high cyclic variations under unthrottled and lean conditions. The addition of hydrogen is potentially helpful for solving this problem. In this test, the engine was run under an speed of 1400 rpm and unthrottled conditions. The hydrogen volume fractions in the intake were respectively kept at 0% and 3%. For a given hydrogen blending level, the ethanol flow rate was reduced to enable the engine to run under lean conditions. The results showed that the engine efficiency was improved with the blending of hydrogen. The highest thermal efficiency was improved by 6.07% after blending 3% hydrogen to the intake air. The addition of hydrogen could increase the engine torque output at lean conditions. Both cooling and exhaust losses were decreased after the hydrogen enrichment while adopting the lean combustion strategy. The hydrogen addition contributed to the extended lean burn limit and decreased cyclic variation under lean conditions. HC and CO emissions were decreased whereas NOx emissions were increased after the blending of hydrogen.

  19. Educational Materials - Burn Wise

    Science.gov (United States)

    Burn Wise outreach material. Burn Wise is a partnership program of that emphasizes the importance of burning the right wood, the right way, in the right wood-burning appliance to protect your home, health, and the air we breathe.

  20. Lean manufacturing measurement: the relationship between lean activities and lean metrics

    Directory of Open Access Journals (Sweden)

    Manotas Duque Diego Fernando

    2007-10-01

    Full Text Available Lean Manufacturing was developed by Toyota Motor company to address their specific needs in a restricted market in times of economic trouble. These concepts have been studied and proven to be transferrable and applicable to a wide variety of industries. This paper aims to integrate a set of metrics that have been proposed by different authors in such a way that they are consistent with the different stages and elements of Lean Manufacturing implementations. To achieve this, two frameworks for Lean implementations are presented and then the main factors for success are used as the basis to propose metrics that measure the advance in these factors. A tabular display of the impact of “Lean activities” on the metrics is presented, proposing that many a priori assumptions about the benefits on many different levels of improvement should be accurate. Finally, some ideas for future research and extension of the applications proposed on this paper are presented as closing points.

  1. Fire-fighting burning oil wells

    International Nuclear Information System (INIS)

    Newbury, Herbert; Risk, Stewart.

    1993-01-01

    A method of extinguishing burning oil wells is presented which involves dispensing liquid nitrogen to the burning site to prevent or inhibit oxygen from fuelling the flames. To carry out the method a remotely operated vehicle is described which is provided with a source of liquid nitrogen and an articulated deployment boom capable of supplying the liquid nitrogen to the site of a burning oil well. (Author)

  2. Rayleigh/Raman/LIF measurements in a turbulent lean premixed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Nandula, S.P.; Pitz, R.W. [Vanderbilt Univ., Nashville, TN (United States); Barlow, R.S. [Sandia National Labs., Livermore, CA (United States)] [and others

    1995-10-01

    Much of the industrial electrical generation capability being added worldwide is gas-turbine engine based and is fueled by natural gas. These gas-turbine engines use lean premixed (LP) combustion to meet the strict NO{sub x} emission standards, while maintaining acceptable levels of CO. In conventional, diffusion flame gas turbine combustors, large amount of NO{sub x} forms in the hot stoichiometric zones via the Zeldovich (thermal) mechanism. Hence, lean premixed combustors are rapidly becoming the norm, since they are specifically designed to avoid these hot stoichiometric zones and the associated thermal NO, However, considerable research and development are still required to reduce the NO{sub x} levels (25-40 ppmvd adjusted to 15% O{sub 2} with the current technology), to the projected goal of under 10 ppmvd by the turn of the century. Achieving this objective would require extensive experiments in LP natural gas (or CH{sub 4}) flames for understanding the combustion phenomena underlying the formation of the exhaust pollutants. Although LP combustion is an effective way to control NO{sub x}, the downside is that it increases the CO emissions. The formation and destruction of the pollutants (NO{sub x} and CO) are strongly affected by the fluid mechanics, the finite-rate chemistry, and their (turbulence-chemistry) interactions. Hence, a thorough understanding of these interactions is vital for controlling and reducing the pollutant emissions. The present research is contributing to this goal by providing a detailed nonintrusive laser based data set with good spatial and temporal resolutions of the pollutants (NO and CO) along with the major species, temperature, and OH. The measurements reported in this work, along with the existing velocity data on a turbulent LP combustor burning CH{sub 4}, would provide insight into the turbulence-chemistry interactions and their effect on pollutant formation.

  3. Lean versus Quick Response Manufacturing og andre koncepter - er Lean den eneste ene?

    DEFF Research Database (Denmark)

    Michelsen, Aage U

    2005-01-01

    Begrebet Lean har gennem de senere år vundet en enorm udbredelse. Antallet af publikationer om Lean har været eksplosivt stigende, og mange virksomheder har gennemført eller gennemfører Lean-projekter. Er Lean et nyt koncept? Er Lean den eneste løsning? Kan Lean kombineres med tankegange og princ...... løsning af en anden produktionsopgave. I fjerde afsnit skitseres kort relationerne mellem Lean og to andre begreber, Six Sigma og TPM, der begge har samme mål som Lean, men forskellige udgangspunkter og forskellige indfaldsvinkler....

  4. Lean Production Applications in a Manufacturing Company

    OpenAIRE

    Ali Görener; Humeyra Baser; Ali Turkyilmaz

    2013-01-01

    Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cyc...

  5. Capability ethics

    OpenAIRE

    Robeyns, Ingrid

    2012-01-01

    textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological theories, virtue ethics, or pragmatism. As I will argue in this chapter, at present the core of the capability approach is an account of value, which together with some other (more minor) normative comm...

  6. Orion Burn Management, Nominal and Response to Failures

    Science.gov (United States)

    Odegard, Ryan; Goodman, John L.; Barrett, Charles P.; Pohlkamp, Kara; Robinson, Shane

    2016-01-01

    An approach for managing Orion on-orbit burn execution is described for nominal and failure response scenarios. The burn management strategy for Orion takes into account per-burn variations in targeting, timing, and execution; crew and ground operator intervention and overrides; defined burn failure triggers and responses; and corresponding on-board software sequencing functionality. Burn-to- burn variations are managed through the identification of specific parameters that may be updated for each progressive burn. Failure triggers and automatic responses during the burn timeframe are defined to provide safety for the crew in the case of vehicle failures, along with override capabilities to ensure operational control of the vehicle. On-board sequencing software provides the timeline coordination for performing the required activities related to targeting, burn execution, and responding to burn failures.

  7. Lean computing for the cloud

    CERN Document Server

    Bauer, Eric

    2016-01-01

    Applies lean manufacturing principles across the cloud service delivery chain to enable application and infrastructure service providers to sustainably achieve the shortest lead time, best quality, and value This book focuses on lean in the context of cloud computing capacity management of applications and the physical and virtual cloud resources that support them. Lean Computing for the Cloud considers business, architectural and operational aspects of efficiently delivering valuable services to end users via cloud-based applications hosted on shared cloud infrastructure. The work also focuses on overall optimization of the service delivery chain to enable both application service and infrastructure service providers to adopt leaner, demand driven operations to serve end users more efficiently. The book’s early chapters analyze how capacity management morphs with cloud computing into interlocked physical infrastructure capacity management, virtual resou ce capacity management, and application capacity ma...

  8. Lean management in academic surgery.

    Science.gov (United States)

    Collar, Ryan M; Shuman, Andrew G; Feiner, Sandra; McGonegal, Amy K; Heidel, Natalie; Duck, Mary; McLean, Scott A; Billi, John E; Healy, David W; Bradford, Carol R

    2012-06-01

    Lean is a management system designed to enhance productivity by eliminating waste. Surgical practice offers many opportunities for improving efficiency. Our objective was to determine whether systematic implementation of lean thinking in an academic otolaryngology operating room improves efficiency and profitability and preserves team morale and educational opportunities. In an 18-month prospective quasi-experimental study, a multidisciplinary task force systematically implemented lean thinking within an otolaryngology operating room of an academic health system. Operating room turnover time and turnaround time were measured during a baseline period; an observer-effect period in which workers were made aware that their efficiency was being measured but before implementing lean changes; and an intervention period after redesign principles had been used. The impact on teamwork, morale, and surgical resident education were measured during the baseline and intervention periods through validated surveys. A profit model was applied to estimate the financial implications of the study. There was no difference between the baseline and observer-effect periods of the study for turnover time (p = 0.98) or turnaround time (p = 0.20). During the intervention period, the mean turnover time and turnaround time were significantly shorter than during the baseline period (29 vs 38 minutes; p improved morale after implementation (p = 0.011). Educational metrics were unchanged before and after implementation. The annual opportunity revenue for the involved operating room is $330,000; when extrapolated throughout the operating rooms, lean thinking could create 6,500 hours of capacity annually. Application of lean management techniques to a single operating room and surgical service improved operating room efficiency and morale, sustained resident education, and can provide considerable financial gains when scaled to an entire academic surgical suite. Copyright © 2012. Published by

  9. An exploratory analysis for Lean and Six Sigma implementation in hospitals: Together is better?

    Science.gov (United States)

    Lee, Jung Young; McFadden, Kathleen L; Gowen, Charles R

    2016-12-22

    Despite the increasing interest for Lean and Six Sigma implementations in hospitals, there has been little empirical evidence that goes beyond descriptive case studies to address the current status and the effectiveness of the implementations. The aim of this study was to explore existing patterns of Lean and Six Sigma implementation in U.S. hospitals and compare the performance of the different patterns. We collected data from 215 U.S. hospitals via a survey that includes measurement items developed from related literature. Using the cross-sectional data, we conducted a cluster analysis, followed by t tests, chi-square tests, and regression analyses for cluster verification. The cluster analysis identifies two clusters, a Moderate Six Sigma group and a Lean Six Sigma group. Results show that the Lean Six Sigma group outperforms the Moderate Six Sigma group across many performance dimensions: responsiveness capability, patient safety, and possibly cost saving. In addition, the Lean Six Sigma group tends to be composed of larger, private teaching hospitals located in more urban areas, and they employ more resources for quality improvement. Our research contributes to the quality management literature by supporting the possible complementary relationship between Lean and Six Sigma in hospitals. Our study encourages practitioners and managers to pay more attention to Lean implementation. Although Lean seems to be conducted in a limited fashion in many hospitals, it should be expanded and combined with Six Sigma for better results.

  10. Lean spare parts delivery chain

    OpenAIRE

    Sjöstrand, Niklas; Larsson, Mona-Liza

    2015-01-01

    AbstractWhen a product has been sold to a customer a new market arises for the company to earn profit from and to differentiate itself within. According to Bartwal, et al. (2010) the after sales market generally does not provide great revenues but good profits of the total revenue. In order to gain competiveness and live up to customer’s expectations a company needs to be efficient (Atkinson, 2004). He continuous that this can be accomplished if companies implement Lean. Lean is different too...

  11. 'Lean' approach gives greater efficiency.

    Science.gov (United States)

    Call, Roger

    2014-02-01

    Adapting the 'Lean' methodologies used for many years by many manufacturers on the production line - such as in the automotive industry - and deploying them in healthcare 'spaces' can, Roger Call, an architect at Herman Miller Healthcare in the US, argues, 'easily remedy many of the inefficiencies' found within a healthcare facility. In an article that first appeared in the September 2013 issue of The Australian Hospital Engineer, he explains how 'Lean' approaches such as the 'Toyota production system', and 'Six Sigma', can be harnessed to good effect in the healthcare sphere.

  12. Dynamic Capabilities

    DEFF Research Database (Denmark)

    Grünbaum, Niels Nolsøe; Stenger, Marianne

    2013-01-01

    The findings reveal a positive relationship between dynamic capabilities and innovation performance in the case enterprises, as we would expect. It was, however, not possible to establish a positive relationship between innovation performance and profitability. Nor was there any positive...... relationship between dynamic capabilities and profitability....

  13. Capability ethics

    NARCIS (Netherlands)

    I.A.M. Robeyns (Ingrid)

    2012-01-01

    textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological

  14. A Simulation of Lean Manufacturing: The Lean Lemonade Tycoon 2

    Science.gov (United States)

    Ncube, Lisa B.

    2010-01-01

    This article discusses the functions and effectiveness of games and simulations in the learning processes, in particular as an experiential learning methodology. The application of the game Lemonade Tycoon in the development of lean manufacturing concepts is described. This article addresses the use of the game to teach the principles of lean…

  15. Learning Lean: A Survey of Industry Lean Needs

    Science.gov (United States)

    Fliedner, Gene; Mathieson, Kieran

    2009-01-01

    The authors examined business practitioners' preferences for higher education curricula design in general and for what graduates should know about Lean, or waste-reduction efforts. The authors conducted a Web-based survey and found that practitioners are not as concerned about graduates' possessing specific technical skills as they are about them…

  16. Lean Application to Manufacturing Ramp-Up

    DEFF Research Database (Denmark)

    Christensen, Irene; Rymaszewska, Anna

    2016-01-01

    . Abstracting from the extant literature, the authors considered the competitiveness of manufacturing companies from two principal perspectives: the leanness of the ramp-up process and the new-value creation of quality managers. While much of the literature fails to acknowledge that the roots of lean actually......This article provides a theoretical overview of the concepts of lean and manufacturing ramp-up in an attempt to conceptualize the strategic areas in which lean philosophy and principles can be applied for continuous improvements. The application of lean principles during the final stage of a new...... product development process, that is, the ramp-up process, is a critical, early enabler of lean manufacturing. The manufacturing strategy literature conceptualizes a state of “leanness in operations,” which can consolidate both the concepts of lean and manufacturing ramp-up, providing a dual perspective...

  17. A Sand Cone Model of Lean Implementation

    OpenAIRE

    Yestemessov, Azamat

    2011-01-01

    Over the past 20 years Lean Production system has been a focus of researches by different academicians. A numerous works have been written in the field of Lean implementation in manufacturing companies. However, as shown, most of the academic topics relate to the issues of implementing Lean tools and techniques. Critical Success Factors have been also described widely; however, no efforts in systematization have been made. Only several works have a focus on integration of Lean implementation ...

  18. Performance Improvement through Implementation of Lean Maintenance

    OpenAIRE

    S. Kolanjiappan; Dr. K. Maran

    2011-01-01

    Lean Maintenance is a relatively new term, invented in the last decade of the twentieth century, but the principles are well established in Total Productive Maintenance (TPM). Lean Maintenance—taking its lead from Lean Manufacturing—applies some new techniques to TPM concepts to render a more structured implementation path. Tracing its roots back to Henry Ford with modern refinements born in Japanese manufacturing, specifically the Toyota Production System (TPS). Lean seeks to eliminate a...

  19. Training for successful lean manufacturing implementation

    OpenAIRE

    Ichimura, Maki; Jahankhani, Hamid; Arunachalam, Subramaniam

    2006-01-01

    Implementing lean manufacturing is a complex and everlasting task. The workers involving in production processes are the pivot of the lean manufacturing implementation. Training is known as a vehicle to assist the implementation process. Despite awareness of the training importance, so far, a little is available to assist to organise an efficient training. This paper summarises the overview of lean manufacturing and discuss the importance of human resource within lean implementation process. ...

  20. Burning plasmas

    International Nuclear Information System (INIS)

    Furth, H.P.; Goldston, R.J.; Zweben, S.J.

    1990-10-01

    The fraction of fusion-reaction energy that is released in energetic charged ions, such as the alpha particles of the D-T reaction, can be thermalized within the reacting plasma and used to maintain its temperature. This mechanism facilitates the achievement of very high energy-multiplication factors Q, but also raises a number of new issues of confinement physics. To ensure satisfactory reaction operation, three areas of energetic-ion interaction need to be addressed: single-ion transport in imperfectly symmetric magnetic fields or turbulent background plasmas; energetic-ion-driven (or stabilized) collective phenomena; and fusion-heat-driven collective phenomena. The first of these topics is already being explored in a number of tokamak experiments, and the second will begin to be addressed in the D-T-burning phase of TFTR and JET. Exploration of the third topic calls for high-Q operation, which is a goal of proposed next-generation plasma-burning projects. Planning for future experiments must take into consideration the full range of plasma-physics and engineering R ampersand D areas that need to be addressed on the way to a fusion power demonstration

  1. Lean and psychosocial work environment in manufacturing

    DEFF Research Database (Denmark)

    Edwards, Kasper; Thye, Nina; Nielsen, Anders P.

    2011-01-01

    Lean is currently the rationalization method of choice in the Danish manufacturing industry. This paper reports finding from three lean implementation cases. All cases are manufacturing companies focusing on upmarket products produced in small series. Prior to lean production was organized as sel...

  2. Lean - set i et historisk perspektiv

    DEFF Research Database (Denmark)

    Michelsen, Aage U

    2006-01-01

    I kapitlet redegøres for, hvordan begrebet Lean opstod som en karakteristik af Toyota Production System (TPS), der igen har sin rod i scientific management. Gennem eksempler illustreres det, at centrale Lean-principper således har været anvendt i årtier. Der argumenteres for, at Lean i mange...

  3. Lean Six Sigma in financial services

    NARCIS (Netherlands)

    de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

    2008-01-01

    Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant

  4. Safety reloaded: lean operations and high involvement work practices for sustainable workplaces

    OpenAIRE

    Camuffo, Arnaldo; De Stefano, Federica; Paolino, Chiara

    2017-01-01

    Starting from the recent quest to investigate the human side of organizational sustainability, this study applies a variety of regression analyses to investigate the effects of Lean Operations, High Involvement Work Practices, and management behaviors on occupational safety. It tests and finds support for the hypotheses that Lean Production systems, High Involvement Work Practices, and two specific management behaviors—workers’ capability development (coaching and teaching of workers) and emp...

  5. Green Lean TQM Human Resource Management Practices in Malaysian Automotive Companies

    OpenAIRE

    Noor Azlina Mohd Salleh; Salmiah Kasolang; Ahmed Jaffar

    2012-01-01

    Green Lean Total Quality Management (LTQM) Human Resource Management (HRM) System is a system comprises of HRM in Environmental Management System (EMS) practices which is integrated to TQM with Lean Manufacturing (LM) principles. HRM is essential especially in dealing with low motivation and less productive employees. The ultimate goal of this system is to focus on achieving total human resource development that is motivated and capable to optimize their creativity to be a part of Green and L...

  6. Change management in lean enterprise

    Directory of Open Access Journals (Sweden)

    Furman Joanna

    2016-06-01

    Full Text Available The main purpose of the paper is the analysis of a process of change focusing particularly on the concept of slimmed production (Lean and its implementation in the enterprise. A case study method was chosen as a research tool because it offers wide array of techniques and means of gaining and analysing data.

  7. Analysis Of Lean Accounting JIT And Balance Scorecard In The Companys Lean Manufacturing

    OpenAIRE

    Irwan Sutirman Wahdiat

    2015-01-01

    This research purpose to analyze the concept of Lean Manufacturing which is influenced by the role of JIT. This research uses a theoretical approach. This study portrait thinking companies that have yet to implement lean manufacturing and after doing the concept of lean manufacturing. This study shows that the concept of lean manufacturing can make the company more efficient and effective. This paper shows some lean manufacturing dimensions of the researchers previous researchers. This study ...

  8. Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

    OpenAIRE

    Alexandra Mirela Cristina MUNTEANU

    2017-01-01

    This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by...

  9. Gossiping Capabilities

    DEFF Research Database (Denmark)

    Mogensen, Martin; Frey, Davide; Guerraoui, Rachid

    Gossip-based protocols are now acknowledged as a sound basis to implement collaborative high-bandwidth content dissemination: content location is disseminated through gossip, the actual contents being subsequently pulled. In this paper, we present HEAP, HEterogeneity Aware gossip Protocol, where...... nodes dynamically adjust their contribution to gossip dissemination according to their capabilities. Using a continuous, itself gossip-based, approximation of relative capabilities, HEAP dynamically leverages the most capable nodes by (a) increasing their fanouts (while decreasing by the same proportion...... declare a high capability in order to augment their perceived quality without contributing accordingly. We evaluate HEAP in the context of a video streaming application on a 236 PlanetLab nodes testbed. Our results shows that HEAP improves the quality of the streaming by 25% over a standard gossip...

  10. Study of gas (CNG) SI engine with pre-chamber. Improvement of the indicated thermal efficiency on lean mixture with EGR and supercharging; Fukushitsushiki hibana tenka asshuku tennen gas (CNG) engine ni kansuru kenkyu. Kakyu to EGR ni yoru kihakuiki no netsukoritsu kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Yonetani, H.; Fukutani, I. [Polytechnic University, Kanagawa (Japan)

    1998-10-15

    As lean burn of compressed natural gas (CNG) is applied to conventional gasoline engines, a combustion period largely increases, resulting in large combustion fluctuation and low thermal efficiency. Heterogeneous spacial air/fuel ratios also have an effect on combustion in lean burn area. By preparing a pre-chamber for a combustion chamber of high- compression ratio CNG pre-mixing SI engines to utilize premixture turbulence, rapid flame propagation is obtained in lean burn area, resulting high combustion performance. Furthermore, study was made on improvement of combustion performance in lean burn area under various compression ratios, intake pressures, pre-chamber shapes and EGR ratios. As a result, lean burn operation at high intake pressure by supercharging showed possible improvement of a thermal efficiency and expansion of inflammable limits. Higher thermal efficiency in lean burn area was also obtained by using higher compression ratios considering heat loss. Although EGR was effective in controlling NOx formed in lean burn area, strict control of both air excess rate and EGR rate was required to prevent lower thermal efficiency. 2 refs., 8 figs., 1 tab.

  11. Burning Mouth Syndrome

    Science.gov (United States)

    ... Care Home Health Info Health Topics Burning Mouth Burning Mouth Syndrome (BMS) is a painful, complex condition often described ... or other symptoms. Read More Publications Cover image Burning Mouth Syndrome Publication files Download Language English PDF — Number of ...

  12. Burning issues

    Energy Technology Data Exchange (ETDEWEB)

    Ashmore, C.

    1998-10-01

    Coal is world`s most abundant source of energy. Turning this potential pollutant into a clean, cost-effective fuel for power production has become a matter for global concern. Some problems and their solutions are highlighted in this article. Environmental problems caused by the giant Mae Moh plant in Thailand were overcome with an extensive retrofit programme that included flue gas desulfurisation systems. For new and smaller coal-fuelled plant, boilers using circulating fluidised bed (CFB) technology provide a cost effective and efficient system which meets environmental standards. A large independent power plant at Colver, Pennsylvania, USA uses CFB technology to burn bituminous gob. AMM and Alstom can provide turnkey packages for coal-fired power plant using a modular concept based on CFB technology. 2 photos.

  13. Exploiting HRM in support of lean manufacturing

    DEFF Research Database (Denmark)

    Jørgensen, Frances; Matthiesen, Rikke

    The purpose of this paper is to investigate the ways in HRM practices are-and could potentially be-exploited to support lean manufacturing in practice. First, a review of the pertinent literature regarding HRM, SHRM, and lean manufacturing is presented to provide an understanding of the mechanisms...... by which HRM practices could, theoretically, be used to support a lean implementation. Data presented in the paper are derived from 1) a longitudinal case study on lean implementation and 2) from managers currently involved with lean manufacturing in a second company. The relevant literature and the data...... depicting the potential role in supporting HRM/lean integrated practices. The analysis of the model with respect to the theoretical background emphasizes a number of areas in which HRM could be more fully exploited in order to more successfully support lean implementation, for example, by stressing HRM...

  14. Lean manufacturing in Indian context: A survey

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar

    2015-04-01

    Full Text Available This paper is an attempt to examine the implementation of Lean Manufacturing system in the Indian industries. Predominant elements of Lean Manufacturing, benefits gained after its implementation and obstacles observed by Indian Industry have been recognized. The results of this survey support the opinion that Lean Manufacturing had potential to improve the organizational performance of Indian industries. Nevertheless, Indian industries are required to be passionate to transform their manufacturing by adopting Lean manufacturing to gain the full benefits. A large numbers of literature papers are available on the better side of Lean manufacturing approach and its benefits gained by manufacturing organizations after implementation. But the adverse impacts of Lean manufacturing are not discussed to a great extent. Some drawbacks of Lean manufacturing are also highlighted in this paper.

  15. Lean Production Applications in a Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Ali Görener

    2016-01-01

    Full Text Available Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cycle times were determined, and Kaizen improvement methods and line balancing methods were applied according to the results. And the last section of study showed conclusion of lean implementation.

  16. Burning Mouth Syndrome and "Burning Mouth Syndrome".

    Science.gov (United States)

    Rifkind, Jacob Bernard

    2016-03-01

    Burning mouth syndrome is distressing to both the patient and practitioner unable to determine the cause of the patient's symptoms. Burning mouth syndrome is a diagnosis of exclusion, which is used only after nutritional deficiencies, mucosal disease, fungal infections, hormonal disturbances and contact stomatitis have been ruled out. This article will explore the many causes and treatment of patients who present with a chief complaint of "my mouth burns," including symptomatic treatment for those with burning mouth syndrome.

  17. Investigation on the lean combustion performance of a hydrogen-enriched n-butanol engine

    International Nuclear Information System (INIS)

    Zhang, Bo; Ji, Changwei; Wang, Shuofeng

    2017-01-01

    Highlights: • H_2 addition avails improving thermal efficiency of n-butanol engines. • Lean burn limit of n-butanol engine is extended by H_2 addition. • H_2 addition shortens the n-butanol engine combustion duration. • HC and CO from the n-butanol engine are decreased by H_2 addition. - Abstract: n-Butanol is a feasible fuel candidate for spark-ignition engines. The current paper carried out an experiment to explore effects of hydrogen addition on further improving the performance of a n-butanol engine under the part load and lean conditions. Within the test, the engine intake pressure and speed were respectively kept at 61.5 kPa and 1400 rpm. The volumetric fractions of hydrogen in the total intake gas (hydrogen + air) were constrained at 0 and 3%, respectively. Under a certain hydrogen blending level, the global excess air ratio of in-cylinder charge which was changed from the stoichiometric to near the lean burn limit was adjusted by varying the n-butanol injection duration. The experimental results confirmed that the brake thermal efficiency was heightened and the lean burn limit was extended after the hydrogen addition. Besides, compared with the pure n-butanol combustion, the hydrogen enrichment enables the engine to gain dropped ignition delay and rapid combustion duration. Moreover, CO and HC from the pure n-butanol engine were reduced by the hydrogen addition. NOx were generally reduced when the excess air ratio was raised. This suggested that NOx from the hydrogen-enriched butanol engine could also be controlled by lean combustion.

  18. Predictors of muscle protein synthesis after severe pediatric burns.

    Science.gov (United States)

    Diaz, Eva C; Herndon, David N; Lee, Jinhyung; Porter, Craig; Cotter, Matthew; Suman, Oscar E; Sidossis, Labros S; Børsheim, Elisabet

    2015-04-01

    Following a major burn, skeletal muscle protein synthesis rate increases but is often insufficient to compensate for massively elevated muscle protein breakdown rates. Given the long-term nature of the pathophysiologic response to burn injury, we hypothesized that muscle protein synthesis rate would be chronically elevated in severely burned children. The objectives of this study were to characterize muscle protein synthesis rate of burned children over a period of 24 months after injury and to identify predictors that influence this response. A total of 87 children with 40% or greater total body surface area (TBSA) burned were included. Patients participated in stable isotope infusion studies at 1, 2, and approximately 4 weeks after burn and at 6, 12, and 24 months after injury to determine skeletal muscle protein fractional synthesis rate. Generalized estimating equations with log link normal distribution were applied to account for clustering of patients and control for patient characteristics. Patients (8 ± 6 years) had large (62, 51-72% TBSA) and deep (47% ± 21% TBSA third degree) burns. Muscle protein fractional synthesis rate was elevated throughout the first 12 months after burn compared with established values from healthy young adults. Muscle protein fractional synthesis rate was lower in boys, in children older than 3 years, and when burns were greater than 80% TBSA. Muscle protein synthesis is elevated for at least 1 year after injury, suggesting that greater muscle protein turnover is a component of the long-term pathophysiologic response to burn trauma. Muscle protein synthesis is highly affected by sex, age, and burn size in severely burned children. These findings may explain the divergence in net protein balance and lean body mass in different populations of burn patients. Prognostic study, level III.

  19. Capability approach

    DEFF Research Database (Denmark)

    Jensen, Niels Rosendal; Kjeldsen, Christian Christrup

    Lærebogen er den første samlede danske præsentation af den af Amartya Sen og Martha Nussbaum udviklede Capability Approach. Bogen indeholder en præsentation og diskussion af Sen og Nussbaums teoretiske platform. I bogen indgår eksempler fra såvel uddannelse/uddannelsespolitik, pædagogik og omsorg....

  20. Leaning in to "muddy" interviews

    DEFF Research Database (Denmark)

    Lippke, Lena; Tanggaard, Lene

    2014-01-01

    Over the last few decades, qualitative research has been acknowledged as a peopled practice in which subjectivities come into play. The main argument presented in this article is that qualitative research involves “muddy,” troublesome, interactional passages, because of a complex interplay between...... situated identities among the participants cross each other. We emphasize the value of daring to lean in to the muddiness of peopled research, use it as an analytical tool and present it in its imperfect form. This approach contributes to transparency in qualitative research, opens up the data in a new way...... subjectivities, situated identities, emotions, and conversational genres. Based on ethnographic fieldwork at a Danish Vocational Educational Training College, we introduce the concept of “leaning in” to provide an analytical grasp of the “muddy” interactional tension field in an interview situation, in which...

  1. Lean six sigma in healthcare.

    Science.gov (United States)

    de Koning, Henk; Verver, John P S; van den Heuvel, Jaap; Bisgaard, Soren; Does, Ronald J M M

    2006-01-01

    Healthcare, as with any other service operation, requires systematic innovation efforts to remain competitive, cost efficient, and up-to-date. This article outlines a methodology and presents examples to illustrate how principles of Lean Thinking and Six Sigma can be combined to provide an effective framework for producing systematic innovation efforts in healthcare. Controlling healthcare cost increases, improving quality, and providing better healthcare are some of the benefits of this approach.

  2. Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

    Directory of Open Access Journals (Sweden)

    Alexandra Mirela Cristina MUNTEANU

    2017-06-01

    Full Text Available This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by author in order to reveal Lean Six Sigma’s benefits.

  3. ENTREPRENEURIAL CAPABILITIES

    DEFF Research Database (Denmark)

    Rasmussen, Lauge Baungaard; Nielsen, Thorkild

    2003-01-01

    The aim of this article is to analyse entrepreneurship from an action research perspective. What is entrepreneurship about? Which are the fundamental capabilities and processes of entrepreneurship? To answer these questions the article includes a case study of a Danish entrepreneur and his networ....... Finally, the article discuss, how more long term action research methods could be integrated into the entrepreneurial processes and the possible impacts of such an implementation?...

  4. The maintenance management for lean organization

    Directory of Open Access Journals (Sweden)

    Daniel D. GEORGESCU

    2010-12-01

    Full Text Available The goal of lean maintenance approach is to maintain organization international competitiveness. In the spirit of continuously improvement, in the paper it is shown how by adjusting some Lean manufacturing specific techniques for Total Productive Maintenance (TPM system, was born new maintenance system named Lean TPM. This is a systemic approach with three techniques, which don’t exclude specific techniques of TPM pillars, but complete them: the 7Ss as a critical first step in any improvement program; instantaneous maintenance; improvement setup operations. In the spirit of Lean principle, Lean TPM adjusts overall equipment effectiveness concept for all supply-chain from supplier to customer. Maintaining equipment in its optimal state and continually improving its productivity is the whole strategy behind Lean TPM.

  5. Cultural Aspects when Implementing Lean Production and Lean Product Development – Experiences from a Swedish Perspective

    Directory of Open Access Journals (Sweden)

    Promporn Wangwacharakul

    2014-07-01

    Full Text Available Lean principles and methods, originating in a Japanese cultural context, have spread to a large number of companies throughout the world. The aim of this case study research is to identify and compare national cultural aspects that influence Lean Production and Lean Product Development implementation in Swedish companies. Data were collected through questionnaires, interviews and an industrial workshop with Swedish Lean practitioners. The study shows that some sub-areas in Lean, such as value definition, control systems, leadership, team development, knowledge management, and strategies, are highly dependent on contextual factors related to human, cultural and organizational aspects. These are related to the national culture and should be considered to a higher extent for successful sustainable implementation of Lean in different cultural contexts. As for implementing Lean in Sweden, national cultural characteristics, such as individualism, autonomy and supportive management style fit well with Lean thinking.

  6. Lean Construction Supply Chain : A Literature Review

    OpenAIRE

    Ren, Jiamei

    2012-01-01

    The aim of this thesis is to enhance the management of supply systems in construction industry using lean principles. This study is an attempt to identify what kind of activities causes’ construction process delay and how to perform lean concept into supply chain in practice. The objective is to assure on-time delivery of information and materials to construction sites at lowest cost and maximum value for the customer. These study problems have been analysed from a lean construction supply ch...

  7. The maintenance management for lean organization

    OpenAIRE

    Daniel D. GEORGESCU

    2010-01-01

    The goal of lean maintenance approach is to maintain organization international competitiveness. In the spirit of continuously improvement, in the paper it is shown how by adjusting some Lean manufacturing specific techniques for Total Productive Maintenance (TPM) system, was born new maintenance system named Lean TPM. This is a systemic approach with three techniques, which don’t exclude specific techniques of TPM pillars, but complete them: the 7Ss as a critical first step in any improvemen...

  8. Apply Lean Thinking in Project Management

    OpenAIRE

    Pham Ngoc, Lan

    2015-01-01

    The purpose of this thesis was to study the effects of Lean Thinking in Project Management and how applying Lean Project Management could enhance the productivity of project work. The study was carried using theoretical research and collecting empirical data from three interviews and one case study at a local company. At the end of the study, the major project management problems at the company were identified and analyzed following Lean Principles. It was also pointed out where there...

  9. Lean Six Sigma in financial services

    OpenAIRE

    de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

    2008-01-01

    Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant results and breakthrough improvements in financial services, as demonstrated with four case studies from Dutch multinational insurance companies. These cases demonstrate the importance of incremental i...

  10. Lean and the quality of work

    DEFF Research Database (Denmark)

    Jensen, Per Langaa

    2008-01-01

    Lean has for the last decade developed as the dominating model for developing productions processes not only within industry but also in health care, administration and service industries in general. With this development a discussion on human factors aspects of lean has developed internationally....... Literature studies documents that it is not possible to establish a clear relation between lean and the psychosocial aspects of work. The studies also indicate that the context and the implementations process play a dominating role in how lean is experienced. This has been the basis for establishing...

  11. Lean education an overview of current issues

    CERN Document Server

    Flumerfelt, Shannon; Kahlen, Franz-Josef

    2017-01-01

    This edited volume presents a structured approach to a new lean education curriculum, implemented for the education of engineers, managers, administrators as well as human resources developers. The authorship comprises professors and lecturers, trainers and practitioners who educate future professionals in Lean Thinking principles and tools. This edited book provides a platform for authors to share their efforts in building a Body of Knowledge (BoK) for Lean Education. The topical spectrum is state-of-the-art in this field, but the book also includes a glimpse into future developments. This is a highly informative and carefully presented book, providing valuable insight for scholars with an interest in Lean Education.

  12. A Methodology for the Assessment of Experiential Learning Lean: The Lean Experience Factory Study

    Science.gov (United States)

    De Zan, Giovanni; De Toni, Alberto Felice; Fornasier, Andrea; Battistella, Cinzia

    2015-01-01

    Purpose: The purpose of this paper is to present a methodology to assess the experiential learning processes of learning lean in an innovative learning environment: the lean model factories. Design/methodology/approach: A literature review on learning and lean management literatures was carried out to design the methodology. Then, a case study…

  13. Lean programm as a method of managing lean changes in the company

    Directory of Open Access Journals (Sweden)

    Suetina Tatiana Aleksandrovna

    2012-12-01

    Full Text Available This article is about methods and ways of providing changes on enterprices which introduce instruments of lean production. The main accent is how to use metodology of the project management by providing lean-changes. Lean program is proposed as a program of strategic developement of enterprices.

  14. Lean and Green Hand Surgery.

    Science.gov (United States)

    Van Demark, Robert E; Smith, Vanessa J S; Fiegen, Anthony

    2018-02-01

    Health care in the United States is both expensive and wasteful. The cost of health care in the United States continues to increase every year. Health care spending for 2016 is estimated at $3.35 trillion. Per capita spending ($10,345 per person) is more than twice the average of other developed countries. The United States also leads the world in solid waste production (624,700 metric tons of waste in 2011). The health care industry is second only to the food industry in annual waste production. Each year, health care facilities in the United States produce 4 billion pounds of waste (660 tons per day), with as much as 70%, or around 2.8 billion pounds, produced directly by operating rooms. Waste disposal also accounts for up to 20% of a hospital's annual environmental services budget. Since 1992, waste production by hospitals has increased annually by a rate of at least 15%, due in part to the increased usage of disposables. Reduction in operating room waste would decrease both health care costs and potential environmental hazards. In 2015, the American Association for Hand Surgery along with the American Society for Surgery of the Hand, American Society for Peripheral Nerve Surgery, and the American Society of Reconstructive Microsurgery began the "Lean and Green" surgery project to reduce the amount of waste generated by hand surgery. We recently began our own "Lean and Green" project in our institution. Using "minor field sterility" surgical principles and Wide Awake Local Anesthesia No Tourniquet (WALANT), both surgical costs and surgical waste were decreased while maintaining patient safety and satisfaction. As the current reimbursement model changes from quantity to quality, "Lean and Green" surgery will play a role in the future health care system. Copyright © 2018 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

  15. Lean production of intensive cities

    DEFF Research Database (Denmark)

    Ratner, Helene Gad; Bojesen, Anders; Bramming, Pia

    2014-01-01

    turnover. This is analysed in terms of Italo Calvino's Invisible cities. It is argued that Calvino's themes and prose help us understand change as a multiplicity of temporal intensities producing ambivalence and affect. We describe this use of literary abstractions as a ‘hyperbolic social epistemology......’. Through the depiction of four intensifications of Lean Production, the metaphors of Calvino's cities show how reality and illusion; hope and poverty; dreams and death and utopia and dystopia are intricately mingled and produce temporary and equally ambivalent affects of alienation, hypocrisy, self...

  16. The LEAN Payload Integration Process

    Science.gov (United States)

    Jordan, Lee P.; Young, Yancy; Rice, Amanda

    2011-01-01

    It is recognized that payload development and integration with the International Space Station (ISS) can be complex. This streamlined integration approach is a first step toward simplifying payload integration; making it easier to fly payloads on ISS, thereby increasing feasibility and interest for more research and commercial organizations to sponsor ISS payloads and take advantage of the ISS as a National Laboratory asset. The streamlined integration approach was addressed from the perspective of highly likely initial payload types to evolve from the National Lab Pathfinder program. Payloads to be accommodated by the Expedite the Processing of Experiments for Space Station (EXPRESS) Racks and Microgravity Sciences Glovebox (MSG) pressurized facilities have been addressed. It is hoped that the streamlined principles applied to these types of payloads will be analyzed and implemented in the future for other host facilities as well as unpressurized payloads to be accommodated by the EXPRESS Logistics Carrier (ELC). Further, a payload does not have to be classified as a National Lab payload in order to be processed according to the lean payload integration process; any payload that meets certain criteria can follow the lean payload integration process.

  17. Lean production and business performance: influences of ...

    African Journals Online (AJOL)

    Hence, this study aims to examine the influence of leadership style in the implementation of lean production. Data were gathered from randomly selected Malaysian manufacturing firms. Findings reveal a positive relationship between lean production and business performance. Specifically, democratic leadership style was ...

  18. Just-in-Time og Lean Manufacturing

    DEFF Research Database (Denmark)

    Michelsen, Aage U.

    2004-01-01

    Filosofi, principper og teknikker i JIT. Princip i Kanban-styring og dimensionering af et Kanban-system. Lean Thinking og Value Stream Mapping.......Filosofi, principper og teknikker i JIT. Princip i Kanban-styring og dimensionering af et Kanban-system. Lean Thinking og Value Stream Mapping....

  19. Indførelse af Lean principper

    DEFF Research Database (Denmark)

    Balmer, Christian; Michelsen, Aage U

    2004-01-01

    I artiklen beskrives, hvorledes lean-principper er indført i en forsikringsvirksomhed samt de opnåede resultater.......I artiklen beskrives, hvorledes lean-principper er indført i en forsikringsvirksomhed samt de opnåede resultater....

  20. Principles of lean planning and control

    NARCIS (Netherlands)

    Riezebos, J.

    2015-01-01

    Lean production systems use teams instead of functional departments as well as simple shop floor control methods to manage the flow of orders at the shop floor. Lean shop floor control focuses on robust and visual methods that are able to cope with variation in processing times, routing sequences,

  1. De praktijk van Lean Six Sigma

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Koning, H.

    2008-01-01

    Zowel Lean als Six Sigma zijn benaderingen van kwaliteits- en efficiëntieverbetering die op dit moment sterk in de belangstelling staan van zowel de industrie als de dienstverlening. Lean Six Sigma integreert beide benaderingen. Ze wordt door sommigen gezien als panacee voor alle mogelijke

  2. Disturbing Practices: Training Workers to Be Lean

    Science.gov (United States)

    Yasukawa, Keiko; Brown, Tony; Black, Stephen

    2014-01-01

    Purpose: The purpose of this paper is to explore the possibilities for expansive learning during organisational change. It considers the introduction of "lean production" as a disturbance to the existing work practices. Design/methodology/approach: The paper considers two case studies of "lean production" training with…

  3. Advancing lean manufacturing, the role of IT

    NARCIS (Netherlands)

    Riezebos, J.; Klingenberg, W.

    This introduction to the special issue discusses the changing role of information technology (IT) in advancing lean production. Lean principles and techniques have been applied in a wide variety of organisations, from make-to-stock to engineer-to-order industries, and even in typical service

  4. Lean in healthcare from employees' perspectives.

    Science.gov (United States)

    Drotz, Erik; Poksinska, Bozena

    2014-01-01

    The purpose of this paper is to contribute toward a deeper understanding of the new roles, responsibilities, and job characteristics of employees in Lean healthcare organizations. The paper is based on three cases studies of healthcare organizations that are regarded as successful examples of Lean applications in the healthcare context. Data were collected by methods including interviews, observations, and document studies. The implementation of Lean in healthcare settings has had a great influence on the roles, responsibilities, and job characteristics of the employees. The focus has shifted from healthcare professionals, where clinical autonomy and professional skills have been the guarding principles of patient care, to process improvement and teamwork. Different job characteristics may make it difficult to implement certain Lean practices in healthcare. Teamwork and decentralization of authority are examples of Lean practices that could be considered countercultural because of the strong professional culture and uneven power distribution, with doctors as the dominant decision makers. Teamwork, value flow orientation, and company-wide involvement in CI were associated with positive effects on the organizations' working environment, staff development, and organizational performance. In order to succeed with Lean healthcare, it is important to understand and recognize the differences in job characteristics between Lean manufacturing and healthcare. This paper provides insights into how Lean implementation changes the roles, responsibilities, and job characteristics of healthcare staff and the challenges and implications that may follow from this.

  5. Lean Six Sigma in a hospital

    NARCIS (Netherlands)

    van den Heuvel, J.; Does, R.J.M.M.; de Koning, H.

    2006-01-01

    Abstract Hospitals today face major challenges. Patients demand quality of care to be improved continuously. Health insurance companies demand the lowest possible prices. Lean Six Sigma is a program that can help healthcare providers to achieve these (seemingly) conflicting goals. Lean Six Sigma is

  6. A fuzzy model for achieving lean attributes for competitive advantages development using AHP-QFD-PROMETHEE

    Science.gov (United States)

    Roghanian, E.; Alipour, Mohammad

    2014-06-01

    Lean production has become an integral part of the manufacturing landscape as its link with superior performance and its ability to provide competitive advantage is well accepted among academics and practitioners. Lean production helps producers in overcoming the challenges organizations face through using powerful tools and enablers. However, most companies are faced with restricted resources such as financial and human resources, time, etc., in using these enablers, and are not capable of implementing all these techniques. Therefore, identifying and selecting the most appropriate and efficient tool can be a significant challenge for many companies. Hence, this literature seeks to combine competitive advantages, lean attributes, and lean enablers to determine the most appropriate enablers for improvement of lean attributes. Quality function deployment in fuzzy environment and house of quality matrix are implemented. Throughout the methodology, fuzzy logic is the basis for translating linguistic judgments required for the relationships and correlation matrix to numerical values. Moreover, for final ranking of lean enablers, a multi-criteria decision-making method (PROMETHEE) is adopted. Finally, a case study in automotive industry is presented to illustrate the implementation of the proposed methodology.

  7. Role of protein and amino acids in promoting lean mass accretion with resistance exercise and attenuating lean mass loss during energy deficit in humans.

    Science.gov (United States)

    Churchward-Venne, Tyler A; Murphy, Caoileann H; Longland, Thomas M; Phillips, Stuart M

    2013-08-01

    Amino acids are major nutrient regulators of muscle protein turnover. After protein ingestion, hyperaminoacidemia stimulates increased rates of skeletal muscle protein synthesis, suppresses muscle protein breakdown, and promotes net muscle protein accretion for several hours. These acute observations form the basis for strategized protein intake to promote lean mass accretion, or prevent lean mass loss over the long term. However, factors such as protein dose, protein source, and timing of intake are important in mediating the anabolic effects of amino acids on skeletal muscle and must be considered within the context of evaluating the reported efficacy of long-term studies investigating protein supplementation as part of a dietary strategy to promote lean mass accretion and/or prevent lean mass loss. Current research suggests that dietary protein supplementation can augment resistance exercise-mediated gains in skeletal muscle mass and strength and can preserve skeletal muscle mass during periods of diet-induced energy restriction. Perhaps less appreciated, protein supplementation can augment resistance training-mediated gains in skeletal muscle mass even in individuals habitually consuming 'adequate' (i.e., >0.8 g kg⁻¹ day⁻¹) protein. Additionally, overfeeding energy with moderate to high-protein intake (15-25 % protein or 1.8-3.0 g kg⁻¹ day⁻¹) is associated with lean, but not fat mass accretion, when compared to overfeeding energy with low protein intake (5 % protein or ~0.68 g kg⁻¹ day⁻¹). Amino acids represent primary nutrient regulators of skeletal muscle anabolism, capable of enhancing lean mass accretion with resistance exercise and attenuating the loss of lean mass during periods of energy deficit, although factors such as protein dose, protein source, and timing of intake are likely important in mediating these effects.

  8. Skaber lean bedre arbejdsmiljø?

    DEFF Research Database (Denmark)

    Hansen, Nanette Juhler

    2007-01-01

    rationalization strategies, among others Lean, claim to improve working conditions. The aim of this thesis is to identify whether the application of Lean strategies leads to a reduction of the occupational health and safety problem repetitive work. Repetitive work is a problem created by the Taylorisation of work......, and therefore it is to be expected that a break with one or more of the Tayloristic principles can lead to a reduction of repetitive work. This thesis points out a number of areas within which Lean breaks with Tayloristic principles, whilst other principles are maintained. These breaks between Lean...... and Taylorism are also found in the study of the case company. By linking breaks with Taylorism with solutions for the reduction of repetitive work, I point out a number of openings in Lean that may lead to a reduction of repetitive work. By using the concept of openings I present the possibilities offered...

  9. THE LEAN AND SIX SIGMA SINERGY

    Directory of Open Access Journals (Sweden)

    Mirko Sokovic

    2008-12-01

    Full Text Available Many organizations, dealing with continuous improvement methods, have realized that Lean and Six Sigma methodologies complement each other. Lean manufacturing focuses on the remova l of waste so that all processes in the total system add value from the customers' perspectives. The main emphasis of Six Sigma is the application of statistical tools in a disciplined manner, which requires data-driven decision-making. The integration of Lean and Six Sigma provides a synergetic effect, a rapid process improvement strategy for attaining organizational goals. When separated, Lean manufacturing cannot bring a process under statistical control, and Six Sigma cannot dramatically improve cycle time or reduce invested capital. Together, synergistic qualities are created to maximize the potential for a process improvement. The paper deals with Lean and Six Sigma principles and approaches used in modern manufacturing for process improvements, and bring forward benefits that are gained when these two methodologies are integrated.

  10. Lean thinking for a maintenance process

    Directory of Open Access Journals (Sweden)

    Sherif Mostafa

    2015-01-01

    Full Text Available The maintenance process shares significant operating costs in an organisation. Lean thinking can be incorporated into maintenance activities through applying its principles and practices/tools. Lean maintenance (LM is a prerequisite for lean manufacturing systems. This research proposes a new structure for LM process based on a systematic literature review of a significant number of related articles that were published on LM. The process structure is designed based on the five lean principles to guide and support organisations to pursue maintenance excellence. This study establishes a scheme for LM tools that are structured into 2 level 4 bundles and 26 lean practices/tools and develops a House of Waste (HoW to demonstrate the association between maintenance wastes and the LM tools. With a successful accomplishment of the proposed scheme, the performance of a maintenance department can create more improvement opportunities over time to reach the maintenance excellence status.

  11. Researching Lean: Methodological implications of loose definitions

    DEFF Research Database (Denmark)

    Brännmark, Mikael; Langstrand, Jostein; Johansson, Stina

    2012-01-01

    practices seem to overlap with other popular management concepts, such as High Performance Work Systems, World Class Manufacturing and Total Quality Management. This confusion, combined with different methodological and theoretical traditions, has led to much debate and contradictory conclusions regarding...... Lean. The purpose of the paper is to illustrate some key methodological issues that need to be considered in future Lean research to allow increased understanding of Lean effects for different stakeholders, primarily meaning the customer, employer and employees. Design/methodology/approach – The paper...... on the case studies, we suggest that future investigations describe the Lean interventions in more detail. General descriptions or analogies, e.g. ‘learning organizations’, presumably increase the present confusion regarding Lean impact on different stakeholders. The case studies also illustrate...

  12. Transferring lean management infrastructure for increasing productivity

    Directory of Open Access Journals (Sweden)

    Ph.D.Daniel Georgescu

    2010-12-01

    Full Text Available These years, manufacturing function have been transferred rapidly and globally from matured countries to emerging countries. In this paper is about the critical elements for successful transfer of lean management among sites and countries. Based on this general descriptive analysis, current global transfer activity of Lean as well as its future direction is also described. According to the gradual progress of lean management transfer, necessity of its refinement/reinforcement is recognized and some research subjects are proposed for contributing further encouragement of its global activities. In this paper, based on this understanding, requisites for transfer of lean management are discussed through investigating global activity of Lean and specification of infrastructure enabling its smooth transfer is examined

  13. Lean Development with the Morpheus Simulation Software

    Science.gov (United States)

    Brogley, Aaron C.

    2013-01-01

    The Morpheus project is an autonomous robotic testbed currently in development at NASA's Johnson Space Center (JSC) with support from other centers. Its primary objectives are to test new 'green' fuel propulsion systems and to demonstrate the capability of the Autonomous Lander Hazard Avoidance Technology (ALHAT) sensor, provided by the Jet Propulsion Laboratory (JPL) on a lunar landing trajectory. If successful, these technologies and lessons learned from the Morpheus testing cycle may be incorporated into a landing descent vehicle used on the moon, an asteroid, or Mars. In an effort to reduce development costs and cycle time, the project employs lean development engineering practices in its development of flight and simulation software. The Morpheus simulation makes use of existing software packages where possible to reduce the development time. The development and testing of flight software occurs primarily through the frequent test operation of the vehicle and incrementally increasing the scope of the test. With rapid development cycles, risk of loss of the vehicle and loss of the mission are possible, but efficient progress in development would not be possible without that risk.

  14. TRUNK LEAN DURING A SINGLE-LEG SQUAT IS ASSOCIATED WITH TRUNK LEAN DURING PITCHING.

    Science.gov (United States)

    Plummer, Hillary A; Oliver, Gretchen D; Powers, Christopher M; Michener, Lori A

    2018-02-01

    Impaired trunk motion during pitching may be a risk factor for upper extremity injuries. Specifically, increased forces about the shoulder and elbow have been observed in pitchers with excessive contralateral trunk lean during pitching. Because of the difficulty in identifying abnormal trunk motions during a high-speed task such as pitching, a clinical screening test is needed to identify pitchers who have impaired trunk motion during pitching. The purpose of this study was to determine the relationship between the degree of lateral trunk lean during the single-leg squat and amount of trunk lean during pitching and if trunk lean during pitching can be predicted from lean during the single-leg squat. Controlled Laboratory Study; Cross-sectional. Seventy-three young baseball pitchers (11.4 ± 1.7 years; 156.3 ± 11.9 cm; 50.5 ± 8.8 kg) participated. An electromagnetic tracking system was used to obtain trunk kinematic data during a single-leg squat task (lead leg) and at maximum shoulder external rotation of a fastball pitch. Pearson correlation coefficients for trunk lean during the single-leg squat and pitching were calculated. A linear regression analysis was performed to determine if trunk lean during pitching can be predicted from lean during the single-leg squat. There was a positive correlation between trunk lean during the single-leg squat and trunk lean during pitching (r = 0.53; plean during the single-leg squat predicted the amount of lateral trunk lean during pitching (R 2 = 0.28; p lean during an SLS and pitching. Trunk lean during the single-leg squat explained 28% of the variance in trunk lean during pitching. Diagnosis, level 3.

  15. Modelling Lean and Green Supply Chain

    Science.gov (United States)

    Duarte, Susana Carla Vieira Lino Medina

    The success of an organization depends on the effective control of its supply chain. It is important to recognize new opportunities for organization and its supply chain. In the last few years the approach to lean, agile, resilient and green supply chain paradigms has been addressed in the scientific literature. Research in this field shows that the integration of these concepts revealed some contradictions among so many paradigms. This thesis is mainly focused on the lean and green approaches. Thirteen different management frameworks, embodied in awards, standards and tools were studied to understand if they could contribute for the modelling process of a lean and green approach. The study reveals a number of categories that are common in most management frameworks, providing adequate conditions for a lean and green supply chain transformation. A conceptual framework for the evaluation of a lean and green organization`s supply chain was proposed. The framework considers six key criteria, namely, leadership, people, strategic planning, stakeholders, processes and results. It was proposed an assessment method considering a criteria score for each criterion. The purpose is to understand how lean and green supply chain can be compatible, using principles, practices, techniques or tools (i.e. elements) that support both, a lean and a green approach, in all key criteria. A case study in the automotive upstream supply chain was performed to understand more deeply if the elements proposed for the conceptual framework could be implemented in a real-scenario. Based on the conceptual framework and the case study, a roadmap to achieve a lean-green transformation is presented. The proposed roadmap revealed its contribution to the understanding on how and when an organization`s supply chain should apply the lean and green elements. This study is relevant to practice, as it may assist managers in the adoption of a lean and green supply chain approach, giving insights for the

  16. Optimization of burn referrals

    DEFF Research Database (Denmark)

    Reiband, Hanna K; Lundin, Kira; Alsbjørn, Bjarne

    2014-01-01

    INTRODUCTION: Correct estimation of the severity of burns is important to obtain the right treatment of the patient and to avoid over- and undertriage. In this study we aimed to assess how often the guidelines for referral of burn injured patients are met at the national burn centre (NBC), Denmar...

  17. Epidemiology of burns

    NARCIS (Netherlands)

    Dokter, Jan

    2016-01-01

    The aim of this thesis is to understand the epidemiology, treatment and outcomes of specialized burn care in The Netherlands. This thesis is mainly based on historical data of the burn centre in Rotterdam from 1986, combined with historical data from the burn centres in Groningen and Beverwijk from

  18. An empirical review of lean manufacturing and their strategies

    Directory of Open Access Journals (Sweden)

    Virender Chahal

    2017-07-01

    Full Text Available The theory of lean manufacturing provides the quality of the products in minimum cost and pro-vides customer satisfaction. Today, the competition level is very high and every industry tries to supply high quality products in nominal cost, so lean is the latest tool to achieve. The objective of this paper is to study different lean concepts under various lean strategies. This study helps to find out the status of lean manufacturing and its ways of implementation. Also in this paper, there is a discussion about lean manufacturing concept, lean waste, lean strategies, lean barriers and cycle of lean implementation. This paper presents a literature review to clear the status of lean manufacturing and their strategies with help of collection of relevant papers.

  19. One-step reduced kinetics for lean hydrogen-air deflagration

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez-Galisteo, D.; Sanchez, A.L. [Area de Mecanica de Fluidos, Univ. Carlos III de Madrid, Leganes 28911 (Spain); Linan, A. [ETSI Aeronauticos, Pl. Cardenal Cisneros 3, Madrid 28040 (Spain); Williams, F.A. [Dept. of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92093-0411 (United States)

    2009-05-15

    A short mechanism consisting of seven elementary reactions, of which only three are reversible, is shown to provide good predictions of hydrogen-air lean-flame burning velocities. This mechanism is further simplified by noting that over a range of conditions of practical interest, near the lean flammability limit all reaction intermediaries have small concentrations in the important thin reaction zone that controls the hydrogen-air laminar burning velocity and therefore follow a steady state approximation, while the main species react according to the global irreversible reaction 2H{sub 2} + O{sub 2} {yields} 2H{sub 2}O. An explicit expression for the non-Arrhenius rate of this one-step overall reaction for hydrogen oxidation is derived from the seven-step detailed mechanism, for application near the flammability limit. The one-step results are used to calculate flammability limits and burning velocities of planar deflagrations. Furthermore, implications concerning radical profiles in the deflagration and reasons for the success of the approximations are clarified. It is also demonstrated that adding only two irreversible direct recombination steps to the seven-step mechanism accurately reproduces burning velocities of the full detailed mechanism for all equivalence ratios at normal atmospheric conditions and that an eight-step detailed mechanism, constructed from the seven-step mechanism by adding to it the fourth reversible shuffle reaction, improves predictions of O and OH profiles. The new reduced-chemistry descriptions can be useful for both analytical and computational studies of lean hydrogen-air flames, decreasing required computation times. (author)

  20. To burn or not to burn

    International Nuclear Information System (INIS)

    Busch, L.

    1993-01-01

    While taking a match to an oil slick may sound like the making of a chaotic inferno, emergency response specialists say burning may be the most efficient way to remove large oil spills from the ocean's surface. But tests of this technique are being resisted by environmentalists as well as the Environmental Protection Agency (EPA), which has final authority over the matter. The debate over test burning arose most recently in Alaska when a proposal to spill and then ignite 1,000 barrels of crude on the Arctic Ocean this past summer was rejected by the EPA. The EPA didn't object to the technique or to the notion of burning spilled oil. However, it contends that it's not necessary to spill thousands of gallons of oil to conduct tests, and unnecessarily pollute the environment, when plenty of oil is already available from accidental spills. Researchers disagree, claiming they won't be able to use the burning technique on an actual spill until it has been tested in a controlled experiment. Despite such concerns, the Canadian government is going ahead with a test burn off the coast of Newfoundland next year. Faced with a choice of test burning or the kind of shoreline contamination left in the wake of the Exxon Valdez disaster, Environment Canada opts for testing. Learning valuable lessons about rapid oil-spill cleanup is worth the relatively minor risks to the environment that test burning would pose

  1. Adapting lean to histology laboratories.

    Science.gov (United States)

    Buesa, René J

    2009-10-01

    Histology laboratories (histolabs) can increase productivity and reduce turnaround time and errors by using any one of several available management tools. After a few years of operation, all histolabs develop workflow problems. Histology laboratories handling more than 20,000 cases per year benefit the most from implementing management tools, as occurred in the 25 facilities summarized in this article. Discontinuous workflow, lack of "pulling" between steps, accepting unavoidable waiting times while working with small batches within work cells, and a workflow with an uneven rate of completion, are some of the adaptations required by the Lean system when it is used in histology because 70% of the tasks are manual and the flow has to be interrupted to add value to the pieces of tissue during tissue processing, no matter how short that step is. After all these adaptations are incorporated, the histolab becomes as "Lean" as it can be, and the qualifier is also a recognition of the effort and personnel involvement in the implementation. Given its service nature, productivity increments do not expand the histolab customer base and could lead to staffing reductions. This is one of the causes of reluctance by some employees for implementing these techniques which are mostly driven by cost reductions sought by insurance companies and administrators, and not necessarily because of a real medical need to reduce the turnaround time. Finally, any histolab wanting to improve its workflow can follow some easy steps presented here as a guide to accomplish that objective. These steps stress the need for the supervisors to insure that the personnel in the histology laboratory are being paid at a comparable rate as other histolabs in the area.

  2. Lean Six Sigma implementation and organizational culture.

    Science.gov (United States)

    Knapp, Susan

    2015-01-01

    The purpose of this paper is to examine the relationship between four organizational cultural types defined by the Competing Values Framework and three Lean Six Sigma implementation components - management involvement, use of Lean Six Sigma methods and Lean Six Sigma infrastructure. The study involved surveying 446 human resource and quality managers from 223 hospitals located in Maine, New Hampshire, Vermont, Massachusetts and Rhode Island using the Organizational Culture Assessment Instrument. Findings - In total, 104 completed responses were received and analyzed using multivariate analysis of variance. Follow-up analysis of variances showed management support was significant, F(3, 100)=4.89, p cultures having significant interactions with management support. The relationship between organizational culture and Lean Six Sigma in hospitals provides information on how specific cultural characteristics impact the Lean Six Sigma initiative key components. This information assists hospital staff who are considering implementing quality initiatives by providing an understanding of what cultural values correspond to effective Lean Six Sigma implementation. Managers understanding the quality initiative cultural underpinnings, are attentive to the culture-shared values and norm's influence can utilize strategies to better implement Lean Six Sigma.

  3. Lean in healthcare: the unfilled promise?

    Science.gov (United States)

    Radnor, Zoe J; Holweg, Matthias; Waring, Justin

    2012-02-01

    In an effort to improve operational efficiency, healthcare services around the world have adopted process improvement methodologies from the manufacturing sector, such as Lean Production. In this paper we report on four multi-level case studies of the implementation of Lean in the English NHS. Our results show that this generally involves the application of specific Lean 'tools', such as 'kaizen blitz' and 'rapid improvement events', which tend to produce small-scale and localised productivity gains. Although this suggests that Lean might not currently deliver the efficiency improvements desired in policy, the evolution of Lean in the manufacturing sector also reveals this initial focus on the 'tool level'. In moving to a more system-wide approach, however, we identify significant contextual differences between healthcare and manufacturing that result in two critical breaches of the assumptions behind Lean. First, the customer and commissioner in the private sector are the one and the same, which is essential in determining 'customer value' that drives process improvement activities. Second, healthcare is predominantly designed to be capacity-led, and hence there is limited ability to influence demand or make full use of freed-up resources. What is different about this research is that these breaches can be regarded as not being primarily 'professional' in origin but actually more 'organisational' and 'managerial' and, if not addressed could severely constrain Lean's impact on healthcare productivity at the systems level. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. The human side of lean teams.

    Science.gov (United States)

    Wackerbarth, Sarah B; Strawser-Srinath, Jamie R; Conigliaro, Joseph C

    2015-05-01

    Organizations use lean principles to increase quality and decrease costs. Lean projects require an understanding of systems-wide processes and utilize interdisciplinary teams. Most lean tools are straightforward, and the biggest barrier to successful implementation is often development of the team aspect of the lean approach. The purpose of this article is to share challenges experienced by a lean team charged with improving a hospital discharge process. Reflection on the experience provides an opportunity to highlight lessons from The Team Handbook by Peter Scholtes and colleagues. To improve the likelihood that process improvement initiatives, including lean projects, will be successful, organizations should consider providing training in organizational change principles and team building. The authors' lean team learned these lessons the hard way. Despite the challenges, the team successfully implemented changes throughout the organization that have had a positive impact. Training to understand the psychology of change might have decreased the resistance faced in implementing these changes. © 2014 by the American College of Medical Quality.

  5. Leading Lean: a Canadian healthcare leader's guide.

    Science.gov (United States)

    Fine, Benjamin A; Golden, Brian; Hannam, Rosemary; Morra, Dante

    2009-01-01

    Canadian healthcare organizations are increasingly asked to do more with less, and too often this has resulted in demands on staff to simply work harder and longer. Lean methodologies, originating from Japanese industrial organizations and most notably Toyota, offer an alternative - tried and tested approaches to working smarter. Lean, with its systematic approaches to reducing waste, has found its way to Canadian healthcare organizations with promising results. This article reports on a study of five Canadian healthcare providers that have recently implemented Lean. We offer stories of success but also identify potential obstacles and ways by which they may be surmounted to provide better value for our healthcare investments.

  6. Laminar burning velocities of near-flammability-limit H{sub 2}-air-steam mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Loesel Sitar, J V; Chan, C K; Torchia, F; Guerrero, A

    1996-12-31

    Laminar burning velocities of lean H{sub 2}-air-steam mixtures near the flammability limit were measured by using the pressure-time history of an expanding flame kernel. Although flames in these mixtures are inherently unstable, this difficulty was avoided by using the early pressure rise of the burn. A comparison of results from that method with burning velocities determined from schlieren photographs of the expanding flame kernel gave good agreement. Despite the difficulties, it is believed that the pressure trace method gives results that are useful in modelling reactor accident scenarios. 8 refs., 4 figs.

  7. Laminar burning velocities of near-flammability-limit H2-air-steam mixtures

    International Nuclear Information System (INIS)

    Loesel Sitar, J.V.; Chan, C.K.; Torchia, F.; Guerrero, A.

    1995-01-01

    Laminar burning velocities of lean H 2 -air-steam mixtures near the flammability limit were measured by using the pressure-time history of an expanding flame kernel. Although flames in these mixtures are inherently unstable, this difficulty was avoided by using the early pressure rise of the burn. A comparison of results from that method with burning velocities determined from schlieren photographs of the expanding flame kernel gave good agreement. Despite the difficulties, it is believed that the pressure trace method gives results that are useful in modelling reactor accident scenarios. 8 refs., 4 figs

  8. Making it lean applying lean practices to the work of it

    CERN Document Server

    Williams, Howard

    2013-01-01

    Making IT Lean: Applying Lean Practices to the Work of IT presents Lean concepts and techniques for improving processes and eliminating waste in IT operations and IT Service Management, in a manner that is easy to understand. The authors provide a context for discussing several areas of application within this domain, allowing you to quickly gain insight into IT processes and Lean principles.The text reviews IT Service Management, with reference to the IT Infrastructure Library (ITIL®) as a framework for best practices-explaining how to use it to accommod

  9. LEAN SIX SIGMA – MULTIPLE CASE STUDY

    Directory of Open Access Journals (Sweden)

    Delvio Venanzi

    2017-12-01

    Full Text Available Lean Six Sigma é uma gestão focada na qualidade e desempenho produtivo em sistemas operacionais. Este artigo discute os fundamentos desta metodologia através de duas diferentes concepções de gestão, Lean Manufacturing e Six Sigma. Primeiro, o artigo explica o DMAIC (definir, medir, analisar, melhorar e controlar e suas respectivas fases, após a filosofia Lean com o sipoc e técnicas de mapeamento de fluxo de valor. O artigo pretende mostrar a integração destes dois conceitos e seus resultados. A metodologia consistiu em uma teoria baseada em uma pesquisa bibliográfica de pesquisa exploratória que consistiu de três estudos de caso em empresas de diferenças localizadas em Sorocaba, São Paulo. Neste artigo estuda a aplicação de Lean Seis Sigma e seus resultados.

  10. Lean Construction Applications for Bridge Inspection

    Science.gov (United States)

    2017-10-01

    Lean philosophy was used to analyze the efficiency of bridge inspection. Emphasis was put on identifying activities that add value to the final output, an owner approved bridge inspection report. 26 bridge inspections were shadowed. Time spent on bri...

  11. Lean in service industries: A literature review

    Science.gov (United States)

    V, Vignesh; Suresh, M.; Aramvalarthan, S.

    2016-09-01

    Lean service is an amalgamation of tools and practices which, if applied appropriately, would definitely improve the existing quality of operations and ensure the generation of a large amount of favourable financial and economic outcomes and improve the behaviour of the workforce. As a result, it assumes of great significance in the fiercely competitive modern world. This article presents a comprehensive bibliographic study about the various lean service practices through a variety of approaches like service improvement, manufacturing, supply chain, market and retailing approaches, etc. Thus it gives a clear view on how the lean services are implemented in various sectors and the contribution of lean service towards improving the quality in the services provided while reducing the costs.

  12. Implementation of Lean Manufacturing in Romanian Organisations

    Directory of Open Access Journals (Sweden)

    Ucenic Camelia Ioana

    2017-01-01

    Full Text Available The implementation of lean manufacturing is one of the main tools for attaining a higher performance level in the Romanian organisations. The study uses data collected at middle management level from organisations located in Transylvania. The organisations come from different fields of activity and are in different stages of lean implementation. The article makes use of quantitative and qualitative instruments for the evaluation of lean in the above mentioned companies. Characteristics as waste reduction, cost, quality, product design have different approaches in the companies. Their way of approach gives useful information regarding the type of company from the point of view of lean manufacturing implementation. This knowledge provides a useful support at different managerial levels in the process of decision making.

  13. Lean six sigma application to transportation logistics

    Directory of Open Access Journals (Sweden)

    Simone Tavares Fernandes

    2012-06-01

    Full Text Available This work presents the application of Lean Six Sigma in a case study of a metallurgic industry. The Six Sigma and the Lean are two processes used by enterprises in Brazil and worldwide. Currently the integration of these processes is a challenge for these companies, which search a way more efficient to reduce their wastes and to adapt to the needs of their markets. The paper had as purpose to demonstrate the applicability of the Lean Six Sigma in a real logistical problem related to the transportation of goods among units of a metallurgic industry. The stages used for the solution of the problem follow the DMAIC cycle – Define, Measure, Analyze, Improve and Control. The paper presents in details the integrated approach of the improvement processes Lean and Six Sigma, their tools set, as well the excellent results obtained in the case study.

  14. LEAN Tools in the IT Sector

    Directory of Open Access Journals (Sweden)

    Zoltan VAJNA

    2015-05-01

    Full Text Available Nowadays the LEAN tools with their proven efficiency are indispensable parts of the production management. I think there is no producing enterprise that cannot utilize a wide variety of these LEAN tools. The question now is how these tools can support companies in increasing the efficiency of their supporting IT processes. In this study I will demonstrate how these well-known LEAN tools from production management can be used in IT management to create more cost-effective, efficient and transparent solutions during the IT system development and IT operation activities. I will show respectively without attempting to be comprehensive the most important tools of the LEAN management and I will analyse how these tools can be used in the IT sector. At the end of this study I will demonstrate what the IT managers think about the practical use of these tools.

  15. A case study of lean, sustainable manufacturing

    Directory of Open Access Journals (Sweden)

    Geoff Miller

    2010-06-01

    Full Text Available A small furniture production company has integrated lean tools and sustainability concepts with discrete event simulation modeling and analysis as well as mathematical optimization to make a positive impact on the environment, society and its own financial success. The principles of lean manufacturing that aid in the elimination of waste have helped the company meet ever increasing customer demands while preserving valuable resources for future generations. The implementation of lean and sustainable manufacturing was aided by the use of discrete event simulation and optimization to overcome deficits in lean’s traditional implementation strategies. Lean and green manufacturing can have a more significant, positive impact on multiple measures of operational performance when implemented concurrently rather than separately. These ideas are demonstrated by three applications.

  16. A Web-Based Lean Simulation Game for Office Operations: Training the Other Side of a Lean Enterprise

    Science.gov (United States)

    Kuriger, Glenn W.; Wan, Huang-da; Mirehei, S. Moussa; Tamma, Saumya; Chen, F. Frank

    2010-01-01

    This research proposes a Web-based version of a lean office simulation game (WeBLOG). The game is designed to be used to train lean concepts to office and administrative personnel. This group belongs to the frequently forgotten side of a lean enterprise. Over four phases, the game presents the following seven lean tools: one-piece flow,…

  17. The Finnish healthcare services lean management.

    Science.gov (United States)

    Hihnala, Susanna; Kettunen, Lilja; Suhonen, Marjo; Tiirinki, Hanna

    2018-02-05

    Purpose The purpose of this paper is to discuss health services managers' experiences of management in a special health-care unit and development efforts from the point of view of the Lean method. Additionally, the aim is to deepen the knowledge of the managers' work and nature of the Lean method development processes in the workplace. The research focuses on those aspects and results of Lean method that are currently being used in health-care environments. Design/methodology/approach These data were collected through a number of thematic interviews. The participants were nurse managers ( n = 7) and medical managers ( n = 7) who applied Lean management in their work at the University Hospital in the Northern Ostrobothnia Health Care District. The data were analysed with a qualitative content analysis. Findings A common set of values in specialized health-care services, development of activities and challenges for management in the use of the Lean manager development model to improve personal management skills. Practical implications Managers in specialized health-care services can develop and systematically manage with the help of the Lean method. This emphasizes assumptions, from the point of view of management, about systems development when the organization uses the Lean method. The research outcomes originate from specialized health-care settings in Finland in which the Lean method and its associated management principles have been implemented and applied to the delivery of health care. Originality/value The study shows that the research results and in-depth knowledge on Lean method principles can be applied to health-care management and development processes. The research also describes health services managers' experiences of using the Lean method. In the future, these results can be used to improve Lean management skills, identify personal professional competencies and develop skills required in development processes. Also, the research findings can be used

  18. Work system innovation: Designing improvement methods for generative capability

    DEFF Research Database (Denmark)

    Hansen, David; Møller, Niels

    2013-01-01

    This paper explores how a work system’s capability for improvement is influenced by its improvement methods. Based on explorative case study at a Lean manufacturing facility, the methods problem solving and Appreciative Inquiry were compared through in-depth qualitative studies over a 12-month...

  19. Developing sustainable business experimentation capability : A case study

    NARCIS (Netherlands)

    Weissbrod, Ilka; Bocken, N.M.P.

    2017-01-01

    This research paper shows how a firm pursues innovation activities for economic, social and environmental value creation in the context of time sensitivity. We make a conceptual link between lean startup thinking, triple bottom line value creation, and organizational capabilities. The case study

  20. Effects of NOX Storage Component on Ammonia Formation in TWC for Passive SCR NOX Control in Lean Gasoline Engines

    Energy Technology Data Exchange (ETDEWEB)

    Prikhodko, Vitaly Y. [ORNL; Pihl, Josh A. [ORNL; Toops, Todd J. [ORNL; Parks, II, James E. [ORNL

    2018-04-01

    A prototype three-way catalyst (TWC) with NOX storage component was evaluated for ammonia (NH3) generation on a 2.0-liter BMW lean burn gasoline direct injection engine as a component in a passive ammonia selective catalytic reduction (SCR) system. The passive NH3 SCR system is a potential approach for controlling nitrogen oxides (NOX) emissions from lean burn gasoline engines. In this system, NH3 is generated over a close-coupled TWC during periodic slightly-rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean, NOX passes through the TWC and is reduced by the stored NH3 on the SCR catalyst. Adding a NOX storage component to a TWC provides two benefits in the context of a passive SCR system: (1) enabling longer lean operation by storing NOX upstream and preserving NH3 inventory on the downstream SCR catalyst; and (2) increasing the quantity and rate of NH3 production during rich operation. Since the fuel penalty associated with passive SCR NOX control depends on the fraction of time that the engine is running rich rather than lean, both benefits (longer lean times and shorter rich times achieved via improved NH3 production) will decrease the passive SCR fuel penalty. However, these benefits are primarily realized at low to moderate temperatures (300-500 °C), where the NOX storage component is able to store NOX, with little to no benefit at higher temperatures (>500 °C), where NOX storage is no longer effective. This study discusses engine parameters and control strategies affecting the NH3 generation over a TWC with NOX storage component.

  1. Lean Implementation : the significance of people and dualism

    OpenAIRE

    Bengt, Halling

    2013-01-01

    Lean, with its origins at the Toyota Motor Company, is a concept that is known to increase effectiveness in manufacturing. The Lean concept is now argued to be relevant not only in manufacturing but in service and health-care delivery as well. The reported results of Lean implementation efforts are divided. There are reports that most of the Lean implementation efforts are not reaching the goal; on the other hand, there are reports of promising results. The divided results from Lean implement...

  2. Lean in the supply chain : research and practice

    OpenAIRE

    Ugochukwu, Paschal

    2012-01-01

    Lean is a management philosophy that enhances customer value through waste elimination and continuous improvement in a system by applying lean principles, practices, and techniques. The focus on lean implementations and research had been typically a single company without extension to the entire supply chain. When the concept of lean is implemented across the entire supply chain, however, it is referred to as lean supply chain. The purpose of this thesis is to create a structure from theory a...

  3. Lean in healthcare: A comprehensive review.

    Science.gov (United States)

    D'Andreamatteo, Antonio; Ianni, Luca; Lega, Federico; Sargiacomo, Massimo

    2015-09-01

    Lean seems to be the next revolution for a better, improved, value-based healhcare. In the last 15 years Lean has been increasingly adapted and adopted in healthcare. Accordingly, Lean healthcare has been developing into a major strand of research since the early 2000s. The aim of this work is to present a comprehensive overview of the main issues highlighted by research on implementation of Lean in a complex contest such as the healthcare one. Comprehensive literature review was conducted in order to identify empirical and theoretical articles published up to September 2013. Thematic analysis was performed in order to extract and synthesis data. 243 articles were selected for analysis. Lean is best understood as a means to increase productivity. Hospital is the more explored setting, with emergency and surgery as the pioneer departments. USA appears to be the leading country for number of applications. The theoretical works have been focused mainly on barriers, challenges and success factors. Sustainability, framework for measurement and critical appraisal remain underestimated themes. Evaluations of "system wide approach" are still low in number. Even though Lean results appear to be promising, findings so far do not allow to draw a final word on its positive impacts or challenges when introduced in the healthcare sector. Scholars are called to explore further the potentiality and the weaknesses of Lean, above all as for the magnitude of investments required and for the engagement of the whole organization it represents increasingly strategic choice, whilst health professionals, managers and policy makers could and should learn from research how to play a pivotal role for a more effective implementation of lean in different health contexts. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  4. Lean tool used in the automotive industry

    Directory of Open Access Journals (Sweden)

    Manuela Ingaldi

    2014-10-01

    Full Text Available In the paper basic concepts of Lean Manufacturing were presented. A company specializing in the development of vehicle dynamics, driver assistance systems, brake systems, seat belt sand electronics technology was characterized. The company is engaged in designing and manufacturing world-class products for the automotive market. The Lean tools used in the production hall, such as Yamazumi chart, machine motion analysis, MTM method and timing, were presented.

  5. Lean tool used in the automotive industry

    OpenAIRE

    Manuela Ingaldi; Marta Jagusiak-Kocik

    2014-01-01

    In the paper basic concepts of Lean Manufacturing were presented. A company specializing in the development of vehicle dynamics, driver assistance systems, brake systems, seat belt sand electronics technology was characterized. The company is engaged in designing and manufacturing world-class products for the automotive market. The Lean tools used in the production hall, such as Yamazumi chart, machine motion analysis, MTM method and timing, were presented.

  6. Implementing lean manufacturing system: ISM approach

    Directory of Open Access Journals (Sweden)

    Naveen Kumar

    2013-09-01

    Full Text Available Purpose: Lean Manufacturing System has emerged as an important area of research in Indian context. The requirement of Lean Manufacturing has increased due to defects in products (semi finished and finished and subsequent increase in cost. In this context, this study is an attempt to develop a structural model of the variables, important to implement Lean Manufacturing System in Indian automobile industry. Design/Methodology/Approach: Various variables of lean manufacturing system implementation have been identified from literature review and experts’ opinions. Contextual relationship among these identified variables has been set after carrying out brainstorming session. Further, classification of the variables has been carried out based upon the driving power and dependence. In addition to this, a structural model of variables to implement lean concept in Indian automobile industry has also been developed using Interpretive Structural Modeling (ISM technique. Questionnaire based survey has also been conducted to rank these variables. Findings: Eighteen variables have been identified from the literature and subsequent discussions with experts. Out of which, nine variables have been identified as dependent and nine variables have been identified as driver. No variable has been identified as linkage variable and autonomous variable. From the model developed, ‘Relative cost benefits’ has been identified as top level dependent variable and top management commitment as bottom level most independent variable. Research limitations/Implications: The model so developed is a hypothetical model based upon experts’ opinions. The conclusions so drawn may be further modified to apply in real situation. Practical implication: Clear understanding of interactions among these variables will help organizations to prioritize and manage these variables more effectively and efficiently to draw advantage from lean manufacturing system implementation

  7. INNOVATION LEAN PRINCIPLES IN AUTOMOTIVE GREEN MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Dušan Sabadka

    2014-12-01

    Full Text Available Today, industries such as automotive and manufacturing industries deal with a lot of environmental regulations. Lean is a production strategy whose fundamental principles drive the industry towards a more effective production of goods and services. The eco-efficiency concept is primary to sustainable development and intends to provide more value with less environmental impact. The aim of this study is to identify and explore the contributions of Lean to reduce environmental impacts that naturally result from industrial activity.

  8. The promise of Lean in health care.

    Science.gov (United States)

    Toussaint, John S; Berry, Leonard L

    2013-01-01

    An urgent need in American health care is improving quality and efficiency while controlling costs. One promising management approach implemented by some leading health care institutions is Lean, a quality improvement philosophy and set of principles originated by the Toyota Motor Company. Health care cases reveal that Lean is as applicable in complex knowledge work as it is in assembly-line manufacturing. When well executed, Lean transforms how an organization works and creates an insatiable quest for improvement. In this article, we define Lean and present 6 principles that constitute the essential dynamic of Lean management: attitude of continuous improvement, value creation, unity of purpose, respect for front-line workers, visual tracking, and flexible regimentation. Health care case studies illustrate each principle. The goal of this article is to provide a template for health care leaders to use in considering the implementation of the Lean management system or in assessing the current state of implementation in their organizations. Copyright © 2013 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

  9. Lean healthcare from a change management perspective.

    Science.gov (United States)

    van Rossum, Lisa; Aij, Kjeld Harald; Simons, Frederique Elisabeth; van der Eng, Niels; Ten Have, Wouter Dirk

    2016-05-16

    Purpose - Lean healthcare is used in a growing number of hospitals to increase efficiency and quality of care. However, healthcare organizations encounter problems with the implementation of change initiatives due to an implementation gap: the gap between strategy and execution. From a change management perspective, the purpose of this paper is to increase scientific knowledge regarding factors that diminish the implementation gap and make the transition from the "toolbox lean" toward an actual transformation to lean healthcare. Design/methodology/approach - A cross-sectional study was executed in an operating theatre of a Dutch University Medical Centre. Transformational leadership was expected to ensure the required top-down commitment, whereas team leadership creates the required active, bottom-up behavior of employees. Furthermore, professional and functional silos and a hierarchical structure were expected to impede the workforce flexibility in adapting organizational elements and optimize the entire process flow. Findings - The correlation and regression analyses showed positive relations between the transformational leadership and team leadership styles and lean healthcare implementation. The results also indicated a strong relation between workforce flexibility and the implementation of lean healthcare. Originality/value - With the use of a recently developed change management model, the Change Competence Model, the authors suggest leadership and workforce flexibility to be part of an organization's change capacity as crucial success factor for a sustainable transformation to lean healthcare.

  10. Implementing Lean Health Reforms in Saskatchewan

    Directory of Open Access Journals (Sweden)

    Greg Marchildon

    2013-07-01

    Full Text Available Saskatchewan has gone further than any other Canadian province in implementing health system process improvements using Lean, a production line discipline that originated with the automobile industry. The goal of the Lean reform is to reduce waste and improve quality and overall health system performance by long-term changes in behaviour. Lean enjoys a privileged position on the provincial government’s agenda because of the policy’s championing by the Deputy Minister of Health and the policy’s fit with the government’s patient-centred care agenda. The implementation of reform depends on a major investment of time in the training and Lean-certification of key leaders and managers in the provincial health system. The Saskatchewan Union of Nurses, the union representing the single largest group of health workers in the province, has agreed to co-operate with the provincial government in implementing Lean-type reforms. Thus far, the government has had limited independent evaluation of Lean while internal evaluations claim some successes.

  11. Implementing Lean Six Sigma to achieve inventory control in supply chain management

    Science.gov (United States)

    Hong, Chen

    2017-11-01

    The inventory cost has important impact on the production cost. In order to get the maximum circulation of funds of enterprise with minimum inventory cost, the inventory control with Lean Six Sigma is presented in supply chain management. The inventory includes both the raw material and the semi-finished parts in manufacturing process. Though the inventory is often studied, the inventory control in manufacturing process is seldom mentioned. This paper reports the inventory control from the perspective of manufacturing process by using statistical techniques including DMAIC, Control Chart, and Statistical Process Control. The process stability is evaluated and the process capability is verified with Lean Six Sigma philosophy. The demonstration in power meter production shows the inventory is decreased from 25% to 0.4%, which indicates the inventory control can be achieved with Lean Six Sigma philosophy and the inventory cost in production can be saved for future sustainable development in supply chain management.

  12. Burn mouse models

    DEFF Research Database (Denmark)

    Calum, Henrik; Høiby, Niels; Moser, Claus

    2014-01-01

    Severe thermal injury induces immunosuppression, involving all parts of the immune system, especially when large fractions of the total body surface area are affected. An animal model was established to characterize the burn-induced immunosuppression. In our novel mouse model a 6 % third-degree b......Severe thermal injury induces immunosuppression, involving all parts of the immune system, especially when large fractions of the total body surface area are affected. An animal model was established to characterize the burn-induced immunosuppression. In our novel mouse model a 6 % third...... with infected burn wound compared with the burn wound only group. The burn mouse model resembles the clinical situation and provides an opportunity to examine or develop new strategies like new antibiotics and immune therapy, in handling burn wound victims much....

  13. Visual communication in lean organizations

    Directory of Open Access Journals (Sweden)

    Iuga Maria Virginia

    2017-01-01

    Full Text Available Many researchers have studied the role and importance of communication and communication types for organizations and their work force. The topic of organizational communication is a constantly changing one. The thing that remains stable throughout this very wide topic is its purpose: communication is vital for the effectiveness and success of organizations of all sizes, types and cultures. In terms of type, one could split up topic by type as followed: verbal, visual and written. This research paper focuses on the visual component at shop floor within automotive organizations. It aims at giving the reader a structured overview on the most appropriate but also lean visual communication practices. In order to establish these methods at shop floor, a survey was conducted among nine big automotive companies in Romania. It was then followed up by a second survey dedicated to check the effectiveness of implementation of these methods in a big automotive organization. The paper presents the analyses, results and the conclusions of this surveys.

  14. The Burning Saints

    DEFF Research Database (Denmark)

    Xygalatas, Dimitris

    . Carrying the sacred icons of the saints, participants dance over hot coals as the saint moves them. The Burning Saints presents an analysis of these rituals and the psychology behind them. Based on long-term fieldwork, The Burning Saints traces the historical development and sociocultural context......, The Burning Saints presents a highly original analysis of how mental processes can shape social and religious behaviour....

  15. Burning mouth syndrome

    OpenAIRE

    K A Kamala; S Sankethguddad; S G Sujith; Praveena Tantradi

    2016-01-01

    Burning mouth syndrome (BMS) is multifactorial in origin which is typically characterized by burning and painful sensation in an oral cavity demonstrating clinically normal mucosa. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to different...

  16. Choosing Wood Burning Appliances

    Science.gov (United States)

    Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

  17. Lean i Norge : opplever norske bedrifter som er mer lean, større økning i kundetilfredshet enn de som er mindre lean?

    OpenAIRE

    Fagereng, Hanne Eline; Askevold, Elisabeth Cathrine

    2010-01-01

    Vi ønsker å måle i hvor stor grad norske bedrifter har implementert lean, og for å måle grad av lean har vi utviklet et rammeverk basert på lean teori. Hovedformålet med lean er å øke kundeverdi med minst mulig ressursbruk, anstrengelse, energi, utstyr, tid, plass, material og kapital (Womack, Roos and Jones 2007). Vi vil utforske om høyere grad av lean fører til mer tilfredse kunder enn de som har lavere grad av lean. Altså om hovedformålet med lean blir oppnådd hvis man implementerer lean i...

  18. Instrumented tube burns: theoretical and experimental observations

    Energy Technology Data Exchange (ETDEWEB)

    Yarrington, Cole Davis [Los Alamos National Laboratory; Obrey, Stephen J [Los Alamos National Laboratory; Foley, Timothy J [Los Alamos National Laboratory; Son, Steven F [Los Alamos National Laboratory

    2009-01-01

    The advent of widely available nanoscale energetic composites has resulted in a flurry of novel applications. One of these applications is the use of nanomaterials in energetic compositions. In compositions that exhibit high sensitivity to stimulus, these materials are often termed metastable intermolecular composites (MIC). More generally, these compositions are simply called nanoenergetics. Researchers have used many different experimental techniques to analyze the various properties of nanoenergetic systems. Among these various techniques, the confined tube burn is a simple experiment that is capable of obtaining much data related to the combustion of these materials. The purpose of this report is to review the current state of the confined tube burn experiment, including the drawbacks of the technique and possible remedies. As this report is intended to focus on the specific experimental technique, data from many different energetic materials, and experimental configurations will be presented. The qualitative and quantitative data that can be gathered using confined tube burn experiments include burning rates, total impulse, pressure rise rate, and burning rate differences between different detector types. All of these measurements lend insight into the combustion properties and mechanisms of specific nanoenergetics. Finally, certain data indicates a more complicated flow scenario which may need to be considered when developing burn tube models.

  19. SUCCESSFUL IMPLEMENTATION OF LEAN AS A MANAGERIAL PRINCIPLE IN HEALTH CARE: A CONCEPTUAL ANALYSIS FROM SYSTEMATIC LITERATURE REVIEW.

    Science.gov (United States)

    Maijala, Riikka; Eloranta, Sini; Reunanen, Tero; Ikonen, Tuija S

    2018-01-01

    The aim of this study was to identify and analyze the characteristics of leadership and management associated with a successful Lean thinking adaptation in healthcare. A systematic literature review was undertaken using electronic databases: PubMed, PubMed Systematic Review, ABI/INFORM, Business Source Complete, Emerald, JBI, and Cinahl. Inclusion criteria were: (i) a description of Lean management or leadership in health care, (ii) a reference to Lean thinking, (iii) a peer-reviewed original research article or a literature review, and (iv) a full text article available in English. Among the 1,754 peer-reviewed articles identified, nine original articles and three systematic reviews met the inclusion criteria. Data on informants, methods, and settings were extracted and collated. Content analysis was used to conduct a review of the nine original studies describing and analyzing the success factors of Lean adaptation. The characteristics of leadership and management were analyzed by using the concept of a managerial windshield that divides leadership and management into four ontological dimensions: activities, style, focus, and purpose, each with typical developmental stages of skills and capabilities. The current study has some limitations: some papers from the journals not indexed in the searched databases may have been overlooked and the literature searches were carried out only for a 5-year period. Considering the results using the windshield concept emphasizes the philosophy, principles, and tools of Lean thinking. Lean leadership and management factors in health care were mainly conceptualized as skills and capabilities such as problem solving, making changes occur, empowering, communicating, coaching, supporting, facilitating, being democratic, organizational learning, and organizational success, all of which represented middle-stage or advanced managerial skills and capabilities. A conceptual analysis of systematically reviewed studies of Lean leadership

  20. Using Dynamic Value Stream Mapping and Lean Accounting Box Scores to Support Lean Implementation

    Science.gov (United States)

    Woehrle, Stephen L.; Abou-Shady, Louay

    2010-01-01

    Lean has proven to be an effective management philosophy for improving businesses in a competitive market by eliminating waste and improving operations. An impact of implementing lean projects is the rapid reduction in inventory levels, which gives management the false impression that profits are decreasing while workers on the shop floor observe…

  1. Burns and military clothing.

    Science.gov (United States)

    McLean, A D

    2001-02-01

    Burn injury is a ubiquitous threat in the military environment. The risks during combat are well recognised, but the handling of fuel, oil, munitions and other hot or flammable materials during peacetime deployment and training also imposes an inherent risk of accidental burn injury. Over the last hundred years, the burn threat in combat has ranged from nuclear weapons to small shoulder-launched missiles. Materials such as napalm and white phosphorus plainly present a risk of burn, but the threat extends to encompass personnel in vehicles attacked by anti-armour weapons, large missiles, fuel-air explosives and detonations/conflagrations on weapons platforms such as ships. Large numbers of burn casualties were caused at Pearl Harbor, in Hiroshima and Nagasaki, Vietnam, during the Arab/Israeli Wars and in the Falkland Islands conflict. The threat from burns is unlikely to diminish, indeed new developments in weapons seek to exploit the vulnerability of the serviceman and servicewoman to burns. Clothing can be a barrier to some types of burn--both inherently in the properties of the material, but also by trapping air between clothing layers. Conversely, ignition of the clothing may exacerbate a burn. There is hearsay that burnt clothing products within a wound may complicate the clinical management, or that materials that melt (thermoplastic materials) should not be worn if there is a burn threat. This paper explores the incidence of burn injury, the mechanisms of heat transfer to bare skin and skin covered by materials, and the published evidence for the complication of wound management by materials. Even light-weight combat clothing can offer significant protection to skin from short duration flash burns; the most vulnerable areas are the parts of the body not covered--face and hands. Multilayered combat clothing can offer significant protection for short periods from engulfment by flames; lightweight tropical wear with few layers offers little protection. Under

  2. Development of a Consistent and Reproducible Porcine Scald Burn Model

    Science.gov (United States)

    Kempf, Margit; Kimble, Roy; Cuttle, Leila

    2016-01-01

    There are very few porcine burn models that replicate scald injuries similar to those encountered by children. We have developed a robust porcine burn model capable of creating reproducible scald burns for a wide range of burn conditions. The study was conducted with juvenile Large White pigs, creating replicates of burn combinations; 50°C for 1, 2, 5 and 10 minutes and 60°C, 70°C, 80°C and 90°C for 5 seconds. Visual wound examination, biopsies and Laser Doppler Imaging were performed at 1, 24 hours and at 3 and 7 days post-burn. A consistent water temperature was maintained within the scald device for long durations (49.8 ± 0.1°C when set at 50°C). The macroscopic and histologic appearance was consistent between replicates of burn conditions. For 50°C water, 10 minute duration burns showed significantly deeper tissue injury than all shorter durations at 24 hours post-burn (p ≤ 0.0001), with damage seen to increase until day 3 post-burn. For 5 second duration burns, by day 7 post-burn the 80°C and 90°C scalds had damage detected significantly deeper in the tissue than the 70°C scalds (p ≤ 0.001). A reliable and safe model of porcine scald burn injury has been successfully developed. The novel apparatus with continually refreshed water improves consistency of scald creation for long exposure times. This model allows the pathophysiology of scald burn wound creation and progression to be examined. PMID:27612153

  3. The relationships between Lean manufacturing, management accounting and firm performance

    DEFF Research Database (Denmark)

    Kristensen, Thomas Borup; Nielsen, Henrik; Grasso, Lawrency

    2016-01-01

    with management accounting practices. Specifically, we document that Lean manufacturing is positively associated with Value Stream Costing, Lean visual controls and, more importantly, measures of labor and materials efficiency. Lean manufacturing is positively related to Lean thinking and both are positively...... associated with operational performance and so are Lean visual controls. We also document that the management accounting practices intervene affecting operational performance and they intervene with Lean thinking as well. Lastly, the relationship between Lean manufacturing and measures of labor and materials......Lean manufacturing has been adopted by numerous western companies as an answer to an increasing competitive environment. Lean manufacturing is seen as an enterprise-wide strategy encompassing a transformation of manufacturing practices, affecting companies’ management accounting practices and...

  4. Tourniquet associated chemical burn

    Directory of Open Access Journals (Sweden)

    Jae-Hyuk Yang

    2012-01-01

    Full Text Available Chemical burn under pneumatic tourniquet is an iatrogenic preventable injury and is rarely reported in the literature. The two important mechanisms are maceration (friction and wetness underneath the tourniquent. In this report, our experience with two illustrative patients who presented with iatrogenic tourniquet associated burn is described.

  5. Burns (For Parents)

    Science.gov (United States)

    ... small, and have sensitive skin that needs extra protection. Although some minor burns aren't cause for concern and can ... burns, the mildest of the three, are limited to the top layer of skin: Signs ... pain, and minor swelling. The skin is dry without blisters. Healing ...

  6. Implementing lean in Malaysian universities: Lean awareness level in an engineering faculty of a local university

    Science.gov (United States)

    Azim Khairi, M.; Rahman, Mohamed Abd

    2018-01-01

    Many academic articles were published in Malaysia promoting the goodness of lean in manufacturing and industrial sectors but less attention was apparently given to the possibility of obtaining the same universal benefits when applying lean in non-manufacturing sectors especially higher education. This study aims to determine the level of lean awareness among a local university’s community taking its Faculty of Engineering (FoE) as the case study. It also seeks to identify typical FoE’s staff perception on lean regarding its benefits and the obstacles in implementing it. A web-based survey using questionnaires was carried out for 215 respondents consisting of academic and administrative staff of the faculty. Statistical Package for the Social Science (SPSS) was used to analyze the survey data collected. A total of 13.95% of respondents returned the forms. Slightly more than half of those responded (56.7%) have encountered some of the lean terms with mean 1.43 and standard deviation 0.504. However, the large amount of standard deviation somewhat indicates that the real level of lean awareness of FoE as a group was low. In terms of lean benefits, reduction of waste was favored (93.3%) by the respondents with mean 0.93 and standard deviation 0.254. For obstacles in implementing lean, lack of knowledge was selected by most respondents (86.7%) to be the major factor with mean 0.87 and standard deviation 0.346. Through the analysis done, the study may conclude that level of lean awareness among the university‘s community was low thus may hinder implementation of lean concept.

  7. Burning mouth syndrome

    Directory of Open Access Journals (Sweden)

    K A Kamala

    2016-01-01

    Full Text Available Burning mouth syndrome (BMS is multifactorial in origin which is typically characterized by burning and painful sensation in an oral cavity demonstrating clinically normal mucosa. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to differentiate between symptom of oral burning and BMS. An interdisciplinary and systematic approach is required for better patient management. The purpose of this study was to provide the practitioner with an understanding of the local, systemic, and psychosocial factors which may be responsible for oral burning associated with BMS, and review of treatment modalities, therefore providing a foundation for diagnosis and treatment of BMS.

  8. Phoenix Society for Burn Survivors

    Science.gov (United States)

    ... in 2018! Learn More For Loved Ones A burn injury doesn't just impact the survivor. Families ... to support longterm recovery, improve the quality of burn care, and prevent burn injury. Explore articles on ...

  9. Optimization of large scale food production using Lean Manufacturing principles

    DEFF Research Database (Denmark)

    Engelund, Eva Høy; Friis, Alan; Breum, Gitte

    2009-01-01

    This paper discusses how the production principles of Lean Manufacturing (Lean) can be applied in a large-scale meal production. Lean principles are briefly presented, followed by a field study of how a kitchen at a Danish hospital has implemented Lean in the daily production. In the kitchen...... not be negatively affected by the rationalisation of production procedures. The field study shows that Lean principles can be applied in meal production and can result in increased production efficiency and systematic improvement of product quality without negative effects on the working environment. The results...... show that Lean can be applied and used to manage the production of meals in the kitchen....

  10. Lean Manufacturing Auto Cluster at Chennai

    Science.gov (United States)

    Bhaskaran, E.

    2012-10-01

    Due the presence of lot of automotive Industry, Chennai is known as Detroit of India, that producing over 40 % of the Indian vehicle and components. Lean manufacturing concepts have been widely recognized as an important tool in improving the competitiveness of industries. This is a continuous process involving everyone, starting from management to the shop floor. Automotive Component Industries (ACIs) in Ambattur Industrial Estate, Chennai has formed special purpose vehicle (SPV) society namely Ambattur Industrial Estate Manufacturers Association (AIEMA) Technology Centre (ATC) lean manufacturing cluster (ATC-LMC) during July 2010 under lean manufacturing competitiveness scheme, that comes under National Manufacturing Competitiveness Programme of Government of India. The Tripartite Agreement is taken place between National Productivity Council, consultants and cluster (ATC-LMC). The objective is to conduct diagnostic study, study on training and application of various lean manufacturing techniques and auditing in ten ACIs. The methodology adopted is collection of primary data/details from ten ACIs. In the first phase, diagnostic study is done and the areas for improvement in each of the cluster member companies are identified. In the second phase, training programs and implementation is done on 5S and other areas. In the third phase auditing is done and found that the lean manufacturing techniques implementation in ATC-LMC is sustainable and successful in every cluster companies, which will not only enhance competitiveness but also decrease cost, time and increase productivity. The technical efficiency of LMC companies also increases significantly.

  11. Lean oncology: a new model for oncologists

    Directory of Open Access Journals (Sweden)

    Montesarchio Vincenzo

    2012-04-01

    Full Text Available Abstract The history of the term Lean is relatively recent and originates from the Toyota Production System (TPS. The term "Lean" means "thin", which refers to a mental process, operational, productive, no-frills, quick but not hasty, consequential to the previous event. The Lean process flows seamlessly into the result, eliminates unnecessary complications to the effect, prevents unnecessary equipment processes. The idea is to 'do more with less', like using the (few available resources in the most productive way possible, through the elimination of all types of waste that inevitably accompanies every stage of a production process. Lean management is primarily a management philosophy, a system of values and behaviors that goes beyond the mere application of the instrument and that, once internalized, will form the nucleus of the corporate culture. "Lean Oncology" is a term coined to identify a methodology of care and treatment to cancer patients, consisting on process simplification, streamlining of the organizational and routes of drug treatment, detection and elimination of waste. Its main objective is the centrality of the patient.

  12. Lean oncology: a new model for oncologists.

    Science.gov (United States)

    Montesarchio, Vincenzo; Grimaldi, Antonio Maria; Fox, Bernard A; Rea, Antonio; Marincola, Francesco M; Ascierto, Paolo A

    2012-04-25

    The history of the term Lean is relatively recent and originates from the Toyota Production System (TPS). The term "Lean" means "thin", which refers to a mental process, operational, productive, no-frills, quick but not hasty, consequential to the previous event. The Lean process flows seamlessly into the result, eliminates unnecessary complications to the effect, prevents unnecessary equipment processes. The idea is to 'do more with less', like using the (few) available resources in the most productive way possible, through the elimination of all types of waste that inevitably accompanies every stage of a production process. Lean management is primarily a management philosophy, a system of values and behaviors that goes beyond the mere application of the instrument and that, once internalized, will form the nucleus of the corporate culture. "Lean Oncology" is a term coined to identify a methodology of care and treatment to cancer patients, consisting on process simplification, streamlining of the organizational and routes of drug treatment, detection and elimination of waste. Its main objective is the centrality of the patient.

  13. LEAN PRACTICES FOR PRODUCT DEVELOPMENT PROCESS

    Directory of Open Access Journals (Sweden)

    Guilherme Luz Tortorella

    2015-06-01

    Full Text Available Lean product development (LPD is an approach that comprises lean principles and management practices that aim to reduce waste and improve operational effectiveness throughout the entire value stream in continuous improvement endless journey. Due to that, the ability to innovate, change and learn continuously is a key element in order to minimize product development problems. Several LPD techniques are presented in the literature as possible enablers for lean implementation. However, little has been known about the impact of these enablers on the problems related to product development processes. Thus, this paper aims to examine the relationship between five LPD practices’ constructs and the occurrence frequency of eleven LPD problems’ constructs in companies that are implementing lean. Moreover, the identification of relevant relationships between LPD practices’ and problems’ constructs may contribute to specify the contexts in which problems are expected to occur. The study sample comprises sixty four companies already undergoing lean implementation both in shop floor and offices area. The results indicate that the same practices’ constructs, which are deemed as influential for minimizing LPD problems, present different relationship intensities among them.

  14. Using Lean to Advance Quality Improvement Research.

    Science.gov (United States)

    Blackmore, Christopher Craig; Williams, Barbara L; Ching, Joan M; Chafetz, Lynne A; Kaplan, Gary S

    2016-01-01

    Quality improvement research skills are not commonplace among quality improvement practitioners, and research on the effectiveness of quality improvement has not always kept pace with improvement innovation. However, the Lean tools applied to quality improvement should be equally relevant to the advancement of quality improvement research. We applied the Lean methods to develop a simplified quality improvement publication pathway enabling a small research methodology group to increase quality improvement research throughout the institution. The key innovations of the pathway are horizontal integration of the quality improvement research methods group across the institution, implementation of a Lean quality improvement research pathway, and application of a just-in-time quality improvement research toolkit. This work provides a road map and tools for the acceleration of quality improvement research. At our institution, the Lean quality improvement research approach was associated with statistically significant increases in the number (annual mean increase from 3.0 to 8.5, p = .03) and breadth of published quality improvement research articles, and in the number of quality improvement research projects currently in process. Application of Lean methods to the quality improvement research process can aid in increasing publication of quality improvement articles from across the institution.

  15. Bevezetés a lean menedzsmentbe – a lean stratégiai alapjai = Introduction to lean management – basic strategic elements of lean

    OpenAIRE

    Losonci, Dávid

    2010-01-01

    A lean menedzsment az értékteremtő folyamatok stratégiai és operatív szintjének meghatározó formálójává vált az elmúlt évtizedekben. Jelen tanulmány stratégiai nézőpontból tárgyalja a lean menedzsment teljes bevezetését. Részletes áttekintést ad a Womack és Jones (2003) által lefektetett lean alapelvekről. Az operatív teljesítményjavulásból származó vevői értékteremtés mellett foglalkozik a tulajdonosi értékteremtéssel, az MRP és a lean szinergikus összekapcsolásával, valamint a lean ideális ...

  16. The Development Of A Theoretical Lean Culture Causal Framework To Support The Effective Implementation Of Lean In Automotive Component Manufacturers

    Directory of Open Access Journals (Sweden)

    Van der Merwe, Karl Robert

    2014-05-01

    Full Text Available Although it is generally accepted that lean manufacturing improves operational performance, many organisations are struggling to adapt to the lean philosophy. The purpose of this study is to contribute to a more effective strategy for implementing the lean manufacturing improvement philosophy. The study sets out both to integrate well-researched findings and theories related to generic organisational culture with more recent research and experience related to lean culture, and to examine the role that culture plays in the effective implementation of lean manufacturing principles and techniques. The ultimate aim of this exercise is to develop a theoretical lean culture causal framework.

  17. Lean for Government: Eliminating the Seven Wastes

    Science.gov (United States)

    Shepherd, Christena C.

    2012-01-01

    With shrinking budgets and a slow economy, it is becoming increasingly important for all government agencies to become more efficient. Citizens expect and deserve efficient and effective services from federal, state and local government agencies. One of the best methods to improve efficiency and eliminate waste is to institute the business process improvement methodologies known collectively as Lean; however, with reduced budgets, it may not be possible to train everyone in Lean or to engage the services of a trained consultant. It is possible, however, to raise awareness of the "Seven Wastes" of Lean in each employee, and encourage them to identify areas for improvement. Management commitment is vital to the success of these initiatives, and it is also important to develop the right metrics that will track the success of these changes.

  18. Contribution of Lean Management to Excellence

    Directory of Open Access Journals (Sweden)

    López-Fresno Palmira

    2014-11-01

    Full Text Available To continuously and systematically improve efficiency and efficacy of processes, organizations need the implication of all employees in continuous improvement and innovation through suitable Quality Management Programs (QMPs. Effectiveness of these programs is directly linked to the requirement employees understand the methodologies and tools used for QM and the benefits that will derivate from their implementation, individually and collectively, so they can commit and implicate. Lean Management is a friendly methodology to continuously and systematically achieve process improvement, so helping the organization seeking operational excellence that contributes to overall excellence. This paper identifies Critical Success Factors (CSFs for an effective implementation of QMPs, suggests Lean Management as an easy-to-understand, powerful and friendly methodology for operational excellence and overall excellence, and presents a case experience of implementation of Lean Management in a health care organization that applies the EFQM model, and the lessons learnt.

  19. Lean Start-up in Established Companies

    DEFF Research Database (Denmark)

    Goduscheit, René Chester

    2018-01-01

    Lean start-up is an emergent perspective on how entrepreneurs can bring new products and services to the market. This approach challenges the dominant role of lengthy business plans, linear product development processes, and seeking complete overview of the potential of the new products....../services before market launch. Instead it suggests that start-ups could benefit from a ‘minimum-viable product’ approach where products and services are launched when they contain critical features. The emphasis in the lean start-up approach is on business models rather than the elaborate business plan...... at the companies (strategy meetings, development workshops etc.). The aim is to shed light on the implications for companies that seek to employ lean start-up. These implications will be aimed at aspects like innovation management, organizational structure, customer relations etc....

  20. Theories of lean management: an empirical evaluation.

    Science.gov (United States)

    Handel, Michael J

    2014-03-01

    Debates within organization theory traditionally argued the relative merits of bureaucracy but today there is broad agreement across different perspectives that bureaucratic organization is inefficient and outmoded. Despite their differences, post-bureaucratic and neo-liberal theories argue that organizations with relatively flat hierarchies and low management overhead are better adapted to current market requirements. Post-bureaucratic theory also argues that employees, as well as firms, benefit from leaner management structures. This paper investigates trends in managerial leanness, proposed explanations for such trends, and the consequences of leanness for firms and employees. Although there is a trend toward flatter management hierarchies, there is only weak support for current claims regarding both the causes and consequences of lean management. Copyright © 2013 Elsevier Inc. All rights reserved.

  1. Peningkatan performansi produksi dengan pendekatan lean six sigma

    Directory of Open Access Journals (Sweden)

    H. Harisupriyanto

    2018-01-01

    analysis.The result was that the value added activity by 22%, Necessary but non-value added activity is 44% and the nonvalue added activity by 34%. There are three critical waste that is waiting, defects and excess waste processing. Sigma value early on waste defect that is equal to 2.70; this sigma value is a problem.Recommendations repairs are create and supervision of the SOP and give a training to improve the capabilities and skills of the workforce. An increasing rate of sigma until 3:10 and a reduction in costs up to 25% Keywords: Losses, activity, RCA, Lean, six-sigma

  2. [Lymphocyte metabolism in children with extensive burns].

    Science.gov (United States)

    Artem'ev, S A; Nazarov, I P; Kamzalakova, N I; Bulygin, G V

    2009-01-01

    The results of the study lead to the conclusion that the development of burn disease in children is accompanied by significant lymphocytic structural metabolic changes that determine the functional capabilities of cells and the immune system as a whole. There is an evident activation of the glutathione antioxidant system, a drastic activation of enzymes that ensure Krebs cycle reactions, as well as activation of anaerobic processes. The above changes are mainly caused by the activated sympathoadrenal system that is characteristic of stresses. The knowledge about the metabolic mechanisms responsible for the development of cellular reactions to burn shock and burn disease permits specification of the elements of the pathogenesis of these severe conditions and substantiation of the possibility of using metabolic correction in the complex treatment of children with the above pathology.

  3. Waste Measurement Techniques For Lean Companies

    Directory of Open Access Journals (Sweden)

    Maciej Pieńkowski

    2014-12-01

    Full Text Available The paper is dedicated to answer the problem of measuring waste in companies, which are implementing Lean Manufacturing concept. Lack of complex identification, quantification an visualization of waste significantly impedes Lean transformation efforts. This problem can be solved by a careful investigation of Muda, Muri and Mura, which represent the essence of waste in the Toyota Production System. Measuring them facilitates complete and permanent elimination of waste in processes. The paper introduces a suggestion of methodology, which should enable company to quantify and visualize waste at a shop floor level.

  4. A Lean Six Sigma journey in radiology.

    Science.gov (United States)

    Bucci, Ronald V; Musitano, Anne

    2011-01-01

    The department of radiology at Akron Children's Hospital embarked on a Lean Six Sigma mission as part of a hospital wide initiative to show increased customer satisfaction, reduce employee dissatisfaction and frustration, and decrease costs. Three processes that were addressed were reducing the MRI scheduling back-log, reconciling discrepancies in billing radiology procedures, and implementing a daily management system. Keys to success is that managers provide opportunities to openly communicate between department sections to break down barriers. Executive leaders must be engaged in Lean Six Sigma for the company to be successful.

  5. The Lean and Global Start-up

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager

    For several decades researchers have studied start-up companies with a focus on international markets, suppliers and networks from their inception and on companies that are establishing new, agile business models. This has resulted in two streams of research: The Born Global and International New...... Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

  6. Improving burn care and preventing burns by establishing a burn database in Ukraine.

    Science.gov (United States)

    Fuzaylov, Gennadiy; Murthy, Sushila; Dunaev, Alexander; Savchyn, Vasyl; Knittel, Justin; Zabolotina, Olga; Dylewski, Maggie L; Driscoll, Daniel N

    2014-08-01

    Burns are a challenge for trauma care and a contribution to the surgical burden. The former Soviet republic of Ukraine has a foundation for burn care; however data concerning burns in Ukraine has historically been scant. The objective of this paper was to compare a new burn database to identify problems and implement improvements in burn care and prevention in this country. Retrospective analyses of demographic and clinical data of burn patients including Tukey's post hoc test, analysis of variance, and chi square analyses, and Fisher's exact test were used. Data were compared to the American Burn Association (ABA) burn repository. This study included 1752 thermally injured patients treated in 20 hospitals including Specialized Burn Unit in Municipal Hospital #8 Lviv, Lviv province in Ukraine. Scald burns were the primary etiology of burns injuries (70%) and burns were more common among children less than five years of age (34%). Length of stay, mechanical ventilation use, infection rates, and morbidity increased with greater burn size. Mortality was significantly related to burn size, inhalation injury, age, and length of stay. Wound infections were associated with burn size and older age. Compared to ABA data, Ukrainian patients had double the length of stay and a higher rate of wound infections (16% vs. 2.4%). We created one of the first burn databases from a region of the former Soviet Union in an effort to bring attention to burn injury and improve burn care. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

  7. Lean Transformation Guidance: Why Organizations Fail To Achieve and Sustain Excellence Through Lean Improvement

    OpenAIRE

    Mohammed Hamed Ahmed

    2013-01-01

    Many companies are complaining that lean didn’t achieve their long-term goals, and the improvement impact was very short-lived. 7 out of each 10 lean projects fail as companies try to use lean like a toolkit, copying and pasting the techniques without trying to adapt the employee’s culture, manage the improvement process, sustain the results, and develop their leaders. When the Toyota production system was created, the main goal was to remove wastes from the shop floor us...

  8. Development of framework for sustainable Lean implementation: an ISM approach

    Science.gov (United States)

    Jadhav, Jagdish Rajaram; Mantha, S. S.; Rane, Santosh B.

    2014-07-01

    The survival of any organization depends upon its competitive edge. Even though Lean is one of the most powerful quality improvement methodologies, nearly two-thirds of the Lean implementations results in failures and less than one-fifth of those implemented have sustained results. One of the most significant tasks of top management is to identify, understand and deploy the significant Lean practices like quality circle, Kanban, Just-in-time purchasing, etc. The term `bundle' is used to make groups of inter-related and internally consistent Lean practices. Eight significant Lean practice bundles have been identified based on literature reviewed and opinion of the experts. The order of execution of Lean practice bundles is very important. Lean practitioners must be able to understand the interrelationship between these practice bundles. The objective of this paper is to develop framework for sustainable Lean implementation using interpretive structural modelling approach.

  9. Lean Production and information technology : Connection or contradiction?

    NARCIS (Netherlands)

    Riezebos, Jan; Klingenberg, Warse; Hicks, Christian

    The principles of Lean Production have enabled organisations in the manufacturing and service sectors to significantly improve their competitiveness. The application of Lean principles, derived from the Toyota Production System has enabled many organisations to Simultaneously improve productivity,

  10. Making of a burn unit: SOA burn center

    Directory of Open Access Journals (Sweden)

    Jayant Kumar Dash

    2016-01-01

    Full Text Available Each year in India, burn injuries account for more than 6 million hospital emergency department visits; of which many require hospitalization and are referred to specialized burn centers. There are few burn surgeons and very few burn centers in India. In our state, Odisha, there are only two burn centers to cater to more than 5000 burn victims per year. This article is an attempt to share the knowledge that I acquired while setting up a new burn unit in a private medical college of Odisha.

  11. Lean Accounting - An Ingenious Solution for Cost Optimization

    OpenAIRE

    Dimi Ofileanu; Dan Ioan Topor

    2014-01-01

    The aim of this work is to present a new concept in accounting management: Lean Accounting. This work explains the way the lean concept was born; its benefits for the production system of the factories and the necessity of applying lean accounting in the factories which have implemented lean production, taking into account both its advantages and the boundaries of the other cost management methods in those factories.

  12. TH-C-9A-01: Lean Tools and Methods

    International Nuclear Information System (INIS)

    Rangaraj, D; Chan, K; Boddu, S; Pawlicki, T; Dieterich, S

    2014-01-01

    Lean thinking has revolutionized the manufacturing industry. Toyota has pioneered and leveraged this aspect of Lean thinking. Application of Lean thinking and Lean Six Sigma techniques into Healthcare and in particular in Radiation Oncology has its merits and challenges. To improve quality, safety and patient satisfaction with available resources or reducing cost in terms of time, staff and resources is demands of today's healthcare. Radiation oncology treatment involves many processes and steps, identifying and removing the non-value added steps in a process can significantly improve the efficiency. Real projects undertaken in radiation oncology department in cutting down the procedure time for MRI guided brachytherapy to 40% less using lean thinking will be narrated. Simple Lean tools and techniques such as Gemba walk, visual control, daily huddles, standard work, value stream mapping, error-proofing, etc. can be applied with existing resources and how that improved the operation in a Radiation Oncology department's two year experience will be discussed. Lean thinking focuses on identifying and solving the root-cause of a problem by asking “Why” and not “Who” and this requires a culture change of no blame. Role of leadership in building lean culture, employee empowerment and trains and develops lean thinkers will be presented. Why Lean initiatives fail and how to implement lean successfully in your clinic will be discussed. Learning Objectives: Concepts of lean management or lean thinking. Lean tools and techniques applied in Radiation Oncology. Implement no blame culture and focus on system and processes. Leadership role in implementing lean culture. Challenges for Lean thinking in healthcare

  13. Investigating employee resistance to Lean transformation: UK case study.

    OpenAIRE

    Bruce, J.; Scott, Philip; Roberts, Martyn

    2011-01-01

    Lean is a business process transformation approach that eliminates ‘wastes’ – activities that generate no value for the customer. Lean originated from the production line but is widely implemented in the service sector. This study investigates human and social factors in a Lean transformation in a ‘knowledge worker’ environment. We identify a paradox: a successful Lean programme in the service sector develops staff who are educated and empowered and thus potential opponents to future business...

  14. TH-C-9A-01: Lean Tools and Methods

    Energy Technology Data Exchange (ETDEWEB)

    Rangaraj, D [Baylor Scott and White Health, Temple, TX (United States); Chan, K [Princess Margaret Hospital, Toronto (Canada); Boddu, S [Temple, TX (United States); Pawlicki, T [UC San Diego, La Jolla, CA (United States); Dieterich, S [UC Davis Medical Center, Sacramento, CA (United States)

    2014-06-15

    Lean thinking has revolutionized the manufacturing industry. Toyota has pioneered and leveraged this aspect of Lean thinking. Application of Lean thinking and Lean Six Sigma techniques into Healthcare and in particular in Radiation Oncology has its merits and challenges. To improve quality, safety and patient satisfaction with available resources or reducing cost in terms of time, staff and resources is demands of today's healthcare. Radiation oncology treatment involves many processes and steps, identifying and removing the non-value added steps in a process can significantly improve the efficiency. Real projects undertaken in radiation oncology department in cutting down the procedure time for MRI guided brachytherapy to 40% less using lean thinking will be narrated. Simple Lean tools and techniques such as Gemba walk, visual control, daily huddles, standard work, value stream mapping, error-proofing, etc. can be applied with existing resources and how that improved the operation in a Radiation Oncology department's two year experience will be discussed. Lean thinking focuses on identifying and solving the root-cause of a problem by asking “Why” and not “Who” and this requires a culture change of no blame. Role of leadership in building lean culture, employee empowerment and trains and develops lean thinkers will be presented. Why Lean initiatives fail and how to implement lean successfully in your clinic will be discussed. Learning Objectives: Concepts of lean management or lean thinking. Lean tools and techniques applied in Radiation Oncology. Implement no blame culture and focus on system and processes. Leadership role in implementing lean culture. Challenges for Lean thinking in healthcare.

  15. Lean management in a non-manufacturing organization

    Directory of Open Access Journals (Sweden)

    Mladen Žvorc

    2013-12-01

    Full Text Available This paper examines the possibilities of a lean approach to non-manufacturing functions, i.e. a market-oriented organization. This refers to purchasing, shipment, storage, sale and delivery of goods; marketing, etc. A lean approach to business operations is discussed and several lean business methods are developed on the basis of which lean management can be used not only in manufacturing, but also in non-manufacturing organizations.

  16. Crude oil burning mechanisms

    DEFF Research Database (Denmark)

    van Gelderen, Laurens; Malmquist, L.M.V.; Jomaas, Grunde

    2015-01-01

    In order to improve predictions for the burning efficiency and the residue composition of in-situ burning of crude oil, the burning mechanism of crude oil was studied in relation to the composition of its hydrocarbon mixture, before, during and after the burning. The surface temperature, flame...... height, mass loss rate and residues of three hydrocarbon liquids (n-octane, dodecane and hexadecane), two crude oils (DUC and REBCO) and one hydrocarbon liquid mixture of the aforementioned hydrocarbon liquids were studied using the Crude Oil Flammability Apparatus. The experimental results were compared...... on the highest achievable oil slick temperature. Based on this mechanism, predictions can then be made depending on the hydrocarbon composition of the fuel and the measured surface temperature....

  17. American Burn Association

    Science.gov (United States)

    ... burn-related care, prevention, education, and research. Our multidisciplinary membership enhances our ability to work toward common goals with other organizations and educational programs. Membership Being a member of ...

  18. New Fashioned Book Burning.

    Science.gov (United States)

    Gardner, Robert

    1997-01-01

    Reports on results of a teacher's experiment in book burning as a lesson accompanying the teaching of Ray Bradbury's "Fahrenheit 451." Discusses student reactions and the purpose of or justification for the experimental lesson. (TB)

  19. Effect of selection for lean growth on gonadal development of ...

    African Journals Online (AJOL)

    A primary objective of commercial pig production is lean meat yield in order to satisfy consumer needs. The majority of the commercial pig breeds in South Africa have been selected for high lean growth potential and reduced backfat thickness. There are indications that selection for high lean meat yield may affect the ...

  20. Using Simulation to Explore Lean Manufacturing Implementation Strategies

    Science.gov (United States)

    Shannon, Patrick W.; Krumwiede, Kip R.; Street, Jeffrey N.

    2010-01-01

    Lean manufacturing, an outgrowth of the Toyota Production System, has spread far beyond the automobile industry and is seen by many leaders as a key management philosophy in the battle to compete on an international scale. Successful implementation of lean requires that managers and employees be educated in the proper application of lean tools and…

  1. Når lean organiserer på hospitalet

    DEFF Research Database (Denmark)

    Hauge, Amalie Martinus

    Lean er kendt og anvendt af mange offentlige organisationer i Danmark. Selv om Leans anvendelighed de fleste steder er slået fast, bliver Lean imidlertid ved med at udfordre og skabe konflikt. Hvorfor det? Dette spørgsmål – og mange andre – bliver belyst i denne rapport, som er baseret på en Ph...

  2. Reducing waste in administrative services with lean principles

    NARCIS (Netherlands)

    Wijnhoven, Alphonsus B.J.M.; Beckers, David; Amrit, Chintan Amrit

    2016-01-01

    In the last few decades, lean techniques have been developed for removing with waste in manufacturing. More recently, lean is used outside the manufacturing context as well. This article focuses on using lean thinking for reducing waste in administrative services, i.e., business services with

  3. Teaching Special Decisions in a Lean Accounting Environment

    Science.gov (United States)

    Haskin, Daniel

    2010-01-01

    Lean accounting has become increasingly important as more and more companies adopt the lean enterprise model or some variation of it. Cost and managerial accounting textbooks continue to use, almost exclusively, models based on standard overhead absorption, which if used in a lean environment will not accurately reflect the benefits from the…

  4. Application of lean thinking to health care: issues and observations

    Science.gov (United States)

    Joosten, Tom; Bongers, Inge; Janssen, Richard

    2009-01-01

    Background Incidents and quality problems are a prime cause why health care leaders are calling to redesign health care delivery. One of the concepts used is lean thinking. Yet, lean often leads to resistance. Also, there is a lack of high quality evidence supporting lean premises. In this paper, we present an overview of lean thinking and its application to health care. Development, theory and application of lean thinking to health care Lean thinking evolved from a tool designed to improve operational shop-floor performance at an automotive manufacturer to a management approach with both operational and sociotechnical aspects. Sociotechnical dynamics have until recently not received much attention. At the same time a balanced approach might lead to a situation where operational and sociotechnial improvements are mutually reinforcing. Application to health care has been limited and focussed mainly on operational aspects using original lean tools. A more integrative approach would be to pay more attention to sociotechnical dynamics of lean implementation efforts. Also, the need to use the original lean tools may be limited, because health care may have different instruments and tools already in use that are in line with lean thinking principles. Discussion We believe lean thinking has the potential to improve health care delivery. At the same time, there are methodological and practical considerations that need to be taken into account. Otherwise, lean implementation will be superficial and fail, adding to existing resistance and making it more difficult to improve health care in the long term. PMID:19696048

  5. Lean-team effectiveness through leader values and members’ informing

    NARCIS (Netherlands)

    van Dun, Desirée Hermina; Wilderom, Celeste P.M.

    2016-01-01

    Purpose Although empirical tests of effective lean-team leadership are scarce, leaders are often blamed when lean work-floor initiatives fail. In the present study, a lean-team leader’s work values are assumed to affect his or her team members’ behaviors and, through them, to attain team

  6. Cull sow knife-separable lean content evaluation at harvest and lean mass content prediction equation development.

    Science.gov (United States)

    Abell, Caitlyn E; Stalder, Kenneth J; Hendricks, Haven B; Fitzgerald, Robert F

    2012-07-01

    The objectives of this study were to develop a prediction equation for carcass knife-separable lean within and across USDA cull sow market weight classes (MWC) and to determine carcass and individual primal cut knife separable lean content from cull sows. There were significant percent lean and fat differences in the primal cuts across USDA MWC. The two lighter USDA MWC had a greater percent carcass lean and lower percent fat compared to the two heavier MWC. In general, hot carcass weight explained the majority of carcass lean variation. Additionally, backfat was a significant variation source when predicting cull sow carcass lean. The findings support using a single lean prediction equation across MWC to assist processors when making cull sow purchasing decisions and determine the mix of animals from various USDA MWC that will meet their needs when making pork products with defined lean:fat content. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Burn-out

    OpenAIRE

    Patricia van Echtelt

    2014-01-01

    Deze publicatie is alleen elektronisch verkrijgbaar (downloaden van deze site) Burn-out (ofwel: emotionele uitputting) komt relatief vaak voor: ongeveer één op de acht werknemers in Nederland heeft er last van. Het wordt dan ook gezien als een serieus maatschappelijk probleem dat beleidsmatig aandacht vergt. Dit rapport presenteert de resultaten van twee specifieke analyses over burn-out. Ten eerste gaan we na wat het effect is van emotionele uitputting op de loopbaan van werknemers. Ten twee...

  8. Smartphone applications in burns.

    Science.gov (United States)

    Wurzer, Paul; Parvizi, Daryousch; Lumenta, David B; Giretzlehner, Michael; Branski, Ludwik K; Finnerty, Celeste C; Herndon, David N; Tuca, Alexandru; Rappl, Thomas; Smolle, Christian; Kamolz, Lars P

    2015-08-01

    Since the introduction of applications (apps) for smartphones, the popularity of medical apps has been rising. The aim of this review was to demonstrate the current availability of apps related to burns on Google's Android and Apple's iOS store as well as to include a review of their developers, features, and costs. A systematic online review of Google Play Store and Apple's App Store was performed by using the following search terms: "burn," "burns," "thermal," and the German word "Verbrennung." All apps that were programmed for use as medical apps for burns were included. The review was performed from 25 February until 1 March 2014. A closer look at the free and paid calculation apps including a standardized patient was performed. Four types of apps were identified: calculators, information apps, book/journal apps, and games. In Google Play Store, 31 apps were related to burns, of which 20 were calculation apps (eight for estimating the total body surface area (TBSA) and nine for total fluid requirement (TFR)). In Apple's App Store, under the category of medicine, 39 apps were related to burns, of which 21 were calculation apps (19 for estimating the TBSA and 17 for calculating the TFR). In 19 out of 32 available calculation apps, our study showed a correlation of the calculated TFR compared to our standardized patient. The review demonstrated that many apps for medical burns are available in both common app stores. Even free available calculation apps may provide a more objective and reproducible procedure compared to manual/subjective estimations, although there is still a lack of data security especially in personal data entered in calculation apps. Further clinical studies including smartphone apps for burns should be performed. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

  9. Burning mouth syndrome

    OpenAIRE

    Zakrzewska, Joanna; Buchanan, John A. G.

    2016-01-01

    Burning mouth syndrome is a debilitating medical condition affecting nearly 1.3 million of Americans. Its common features include a burning painful sensation in the mouth, often associated with dysgeusia and xerostomia, despite normal salivation. Classically, symptoms are better in the morning, worsen during the day and typically subside at night. Its etiology is largely multifactorial, and associated medical conditions may include gastrointestinal, urogenital, psychiatric, neurologic and met...

  10. Burning mouth syndrome: update

    OpenAIRE

    Cassol Spanemberg, Juliana; Rodríguez de Rivera Campillo, Ma Eugenia; Jané Salas, Enric; López López, José, 1958-

    2014-01-01

    Burning Mouth Syndrome (BMS) is a chronic disorder that predominately affects middle-aged women in the postmenopausal period. The condition is distinguished by burning symptoms of the oral mucosa and the absence of any clinical signs. The etiology of BMS is complex and it includes a variety of factors. Local, systemic and psychological factors such as stress, anxiety and depression are listed among the possible causes of BMS. BMS may sometimes be classified as BMS Type I, II or III. Although ...

  11. Burning mouth syndrome

    OpenAIRE

    Jimson, Sudha; Rajesh, E.; Krupaa, R. Jayasri; Kasthuri, M.

    2015-01-01

    Burning mouth syndrome (BMS) is a complex disorder that is characterized by warm or burning sensation in the oral mucosa without changes on physical examination. It occurs more commonly in middle-aged and elderly women and often affects the tip of the tongue, lateral borders, lips, hard and soft palate. This condition is probably of multi-factorial origin, often idiopathic, and its etiopathogensis is unknown. BMS can be classified into two clinical forms namely primary and secondary BMS. As a...

  12. IMPROVING PERFORMANCE OF BISCUIT PRODUCTION PROCESS THROUGH LEAN SIX-SIGMA AT PT XYZ

    Directory of Open Access Journals (Sweden)

    Ahmad Mukti Almansur

    2017-05-01

    Full Text Available This research aims to analyze waste or loss using the 7-waste approach and value added/non value added activities in the production process at PT. XYZ. This research also aims to evaluate the production process capability and sigma values at PT. XYZ and used DMAIC technique (Define, Measure, Analysis, Improvement, and Control from Lean Six-sigma with an analysis using Failure Mode and Effect Analysis (FMEA. The results of the research obtained the values of Process Cycle Efficiency (PCE of 47.29%, CTQ (Critical to Quality and process capability value in the form of Cpm (Capability Index for each process stage and yield. Line-5 has DPMO (Defects per Million Opportunities value of 29,632,607 with a Sigma Score 3.39, and FMEA (Failure Mode and Effect Analysis analysis resulted in recommendations for improvement at each process stage.Keywords: process cycle efficiency, biscuit, lean six-sigma, CTQ, CpmABSTRAKPenelitian ini bertujuan melakukan analisis tingkat pemborosan (waste/loss dengan menggunakan pendekatan 7 waste dan value added/non value added activity dalam proses produksi di PT. XYZ. Selanjutnya, melakukan evaluasi terhadap nilai kapabilitas proses produksi dan nilai sigma di PT. XYZ. Penelitian ini menggunakan teknik DMAIC (Define, Measure, Analysis, Improvement, and Control dari Lean Six Sigma dengan Analisis menggunakan menggunakan alat Failure Mode and Effect Analysis (FMEA. Hasil Penelitian mendapati nilai Process Cycle Efficiency (PCE 47.29%, CTQ (Critical to Quality dan nilai kapabilitas proses berupa Cpm (Capability Index setiap tahapan proses dan Yield. Line-5 memiliki DPMO (Defects Per Million Opportunities sebesar 29632.607 dengan Sigma Score 3.39 Sigma, analisis FMEA(Failure Mode and Effect Analysis menghasilkan rekomendasi perbaikan di setiap tahapan proses.Kata kunci: process cycle efficiency, biskuit, lean six sigma, CTQ, Cpm

  13. Simulation of Lean Principles Impact in a Multi-Product Supply Chain

    OpenAIRE

    Matteo, Rossini; Alberto, Portioli Staudacher

    2015-01-01

    The market competition is moving from the single firm to the whole supply chain because of increasing competition and growing need for operational efficiencies and customer orientation. Supply chain management allows companies to look beyond their organizational boundaries to develop and leverage resources and capabilities of their supply chain partners. This creates competitive advantages in the marketplace and because of this SCM has acquired strategic importance. Lean ...

  14. Lean Transformation Guidance: Why Organizations Fail To Achieve and Sustain Excellence Through Lean Improvement

    Directory of Open Access Journals (Sweden)

    Mohammed Hamed Ahmed

    2013-06-01

    Full Text Available Many companies are complaining that lean didn’t achieve their long-term goals, and the improvement impact was very short-lived. 7 out of each 10 lean projects fail as companies try to use lean like a toolkit, copying and pasting the techniques without trying to adapt the employee’s culture, manage the improvement process, sustain the results, and develop their leaders. When the Toyota production system was created, the main goal was to remove wastes from the shop floor using some lean techniques and tools. What was not clear is that this required from Toyota a long process of leadership development, and a high commitment to training and coaching their employee. A Failure to achieve and sustain the improvement is a problem of both management and leadership as well as the improper understanding of the human behavior, and the required culture to success.

  15. Systems Thinking, Lean Production and Action Learning

    Science.gov (United States)

    Seddon, John; Caulkin, Simon

    2007-01-01

    Systems thinking underpins "lean" management and is best understood through action-learning as the ideas are counter-intuitive. The Toyota Production System is just that--a system; the failure to appreciate that starting-place and the advocacy of "tools" leads many to fail to grasp what is, without doubt, a significant…

  16. Lean leiderschap voor (nog) betere teamprestaties

    NARCIS (Netherlands)

    van Dun, Desirée Hermina; Wilderom, Celeste P.M.

    2016-01-01

    Veel managers en teams hebben moeite om continu te blijven verbeteren. Recent onderzoek van de Universiteit Twente laat zien dat er bij het toepassen van lean meer aandacht nodig is voor gedragsontwikkeling van zowel medewerkers als leidinggevenden. Managers met bepaalde gedragskenmerken creëren een

  17. Lean Six Sigma: Stap voor stap

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Koning, H.; de Mast, J.

    2008-01-01

    Lean Six Sigma is de culminatie van ontwikkelingen in kwaliteitsverbetering in de 20ste eeuw. Het combineert belangrijke principes en technieken in een goed gestructureerde en geïntegreerde benadering. Het belichaamt wetenschappelijke inzichten over onderzoeksmethodologie, management en economie. In

  18. Lean leadership and change management skills

    NARCIS (Netherlands)

    Frank Willems

    2013-01-01

    Gastcollege Masteropleiding MIM Tilburg University/TiasNimbas Business School op 17 & 18 mei 2013. • Basic principles of Change Management • Group practice • TheoryU and Social Networking theory as framework for Leadership • Theory about Lean thinking as a method for improving Leadership skills and

  19. Lean approaches in a knowledge worker environment

    CSIR Research Space (South Africa)

    Christelis, L

    2012-08-01

    Full Text Available Most of us are familiar with the concept of Lean (a way to do more and more with less and less). The principles have been applied by the Japanese as part of the Toyota Production System from as early as the 1950's. Subsequently many have applied...

  20. Lean and Agile: An Epistemological Reflection

    Science.gov (United States)

    Browaeys, Marie-Joelle; Fisser, Sandra

    2012-01-01

    Purpose: The aim of the paper is to contribute to the discussion of treating the concepts of lean and agile in isolation or combination by presenting an alternative view from complexity thinking on these concepts, considering an epistemological approach to this topic. Design/methodology/approach: The paper adopts an epistemological approach, using…

  1. Implementing Lean Six Sigma in organizations

    NARCIS (Netherlands)

    Lameijer, B.A.

    2017-01-01

    This thesis focuses on operational excellence following the Lean Six Sigma (LSS) method. As the popularity of implementing LSS grows, questions about implementing LSS in organizations arise, and this is where we aim to contribute. We study key questions about implementing LSS in organizations at two

  2. Modelling green and lean supply chains

    DEFF Research Database (Denmark)

    Govindan, Kannan; Carvalho, Helena; Azevedo, Susana G.

    2017-01-01

    This manuscript proposes a model to support decision making and to help managers identify the best set of green and lean supply chain management practices to improve their eco-efficiency. To attain this objective, a mathematical model based on eco-efficiency concepts is suggested to overcome...... a strategic framework to support the design of eco-efficient supply chains....

  3. Implementing lean in a surgical ward

    DEFF Research Database (Denmark)

    Edwards, Kasper; Nielsen, Anders Paarup; Jacobsen, Peter

    be planned (in detail) in advance. The remaining operating rooms are allocated to this flow and there have been no significant changes to the organization of work in these theaters. Lean management is derived from the Toyota production system and is a comprehensive system of tools and techniques...

  4. Performance management practices in lean manufacturing organizations

    NARCIS (Netherlands)

    Bellisario, Andrea; Pavlov, Andrey

    2018-01-01

    This paper provides the first systematic look into the existing research on performance management (PM) practices employed in lean manufacturing organisations (LMOs). It adopts a systematic review method to examine the evidence generated in the period 2004 – 2015 and uses a comprehensive PM

  5. Lean planning and control : principles and practice

    NARCIS (Netherlands)

    Riezebos, Jan; Suer, Gursel; Gen, Mitsuo

    2018-01-01

    A basic characteristic of lean, agile, and responsive production systems are the use of teams instead of functional departments. Another characteristic is the use of rather simple shop floor control methods to manage the flow of orders. The shop floor control methods provide robust and visual

  6. Personality characteristics of excellent lean managers

    DEFF Research Database (Denmark)

    Steendahl Nielsen, Jacob; Boer, Harry; Lindgren, Peter

    2016-01-01

    Today many Danish companies are implementing Lean and hereby trying to implement a continuous improvement (CI) program and culture. We have observed that companies can easily implement the artifacts of CI, such as Kaizen boards, Kaizen meetings, Performance management (KPI), A3 and PDCA reports...

  7. Lowlands sociotechnical design theory and lean production

    NARCIS (Netherlands)

    Christis, Jac; Soepenberg, Erik; Mohr, Bernard J.; van Amelsvoort, Pierre

    2015-01-01

    Lean Production (LP) can be regarded as a design approach in search of a theoretical foundation. In this paper we show that Lowlands’ Sociotechnical Design Theory (STSL) could function as such a foundation. To reach this goal, we first describe STSL as a system theoretical reformulation of Original

  8. Measuring lean implementation for maintenance service companies

    NARCIS (Netherlands)

    de Jong, Stephan J.; Beelaerts van Blokland, W.W.A.

    2016-01-01

    Purpose – Implementation of lean manufacturing is currently performed in the production industry; however, for the airline maintenance service industry, it is still in its infancy. Indicators such as work in process, cycle time, on-time performance and inventory are useful indicators to measure

  9. The Scientific Underpinning of Lean Six Sigma

    NARCIS (Netherlands)

    Does, R.J.M.M.; de Mast, J.; de Koning, H.; Bisgaard, S.

    2007-01-01

    The twentieth century saw an incredible development of professional organizations. The impact of technological advances is obvious, but besides these, innovations in management structures and methods have resulted in the highly productive organizations of today. Lean Six Sigma is not revolutionary.

  10. Lean Six Sigma for Service and Healthcare

    NARCIS (Netherlands)

    de Mast, J.; Does, R.J.M.M.; de Koning, H.

    2006-01-01

    Lean Six Sigma is built on principles and methods that have proven themselves over the twentieth century. It has incorporated the most effective approaches and integrated them into a full programme. It offers a management structure for organizing continuous improvement of routine tasks, such as

  11. Lean Sygehuset - del I: En patienthistorie

    DEFF Research Database (Denmark)

    Laursen, Martin Lindgaard; Gertsen, Frank

    Denne forskningsrapport introducerer et forskningsprojekt baseret på case studier af Lean principper anvendt på Skejby sygehus. Operationelle udfordringer i sygehusets arbejdsgange illustreres gennem et observeret patientforløb. Disse udfordringer, et oprids af sygehusenes vilkår, og gennemgang af...

  12. Rights, goals, and capabilities

    NARCIS (Netherlands)

    van Hees, M.V.B.P.M

    This article analyses the relationship between rights and capabilities in order to get a better grasp of the kind of consequentialism that the capability theory represents. Capability rights have been defined as rights that have a capability as their object (rights to capabilities). Such a

  13. Lean automation development : applying lean principles to the automation development process

    OpenAIRE

    Granlund, Anna; Wiktorsson, Magnus; Grahn, Sten; Friedler, Niklas

    2014-01-01

    By a broad empirical study it is indicated that automation development show potential of improvement. In the paper, 13 lean product development principles are contrasted to the automation development process and it is suggested why and how these principles can facilitate, support and improve the automation development process. The paper summarises a description of what characterises a lean automation development process and what consequences it entails. Main differences compared to current pr...

  14. Leveraging lean in the office: Lean office needs a novel and differentiated approach

    OpenAIRE

    Rüttimann, Bruno G.; Fischer, Urs P.; Stöckli, Martin T.

    2014-01-01

    Lean Six Sigma tools have been increasingly employed also in the service industry, however with different success as field studies have shown. The reason not only has to be attributed to a poor Change Management, but can also be attributed to the intrinsic characteristics of the Lean techniques, which have been tailored to sustain a stable customer-takted pull-manufacturing principle. An office workplace shows significant differences to a procedural shop floor environment, as it comprises bot...

  15. TOWARDS GREEN THROUGH LEAN/LEAN SIX SIGMA APPROACHES: A LITERATURE REVIEW AT SERVICE INDUSTRY

    Directory of Open Access Journals (Sweden)

    RODRIGO GOYANNES GUSMÃO CAIADO

    2017-08-01

    Full Text Available In the last decades, sustainable development have increasingly gained importance to service industry and lean/Six Sigma approaches are becoming more and more outstanding in order to improve sustainability performance. In the post-modern era the integration between those approaches are necessary in order to aid organisations to balance the need for operational efficiency in their production and service systems with environmental commitment and social fairness. Because of that, Lean Six Sigma practices are progressively becoming widespread in studies about service, as way to improve quality, efficiency, effectiveness and sustainability of services. The purpose of this paper is to critically review the Lean and Lean Six Sigma (L6σ methodologies and highlight their importance to achieve sustainable development in service industry. To do this, a systematic literature review (SLR of the subjects under investigation was conducted. We examine the compatibility and divergences of the green, lean and Six Sigma concepts and implications regarding its sustainable implementation in service industry. The study has two major contributions. First, it is one of the first researches that investigate the potential benefits of integrating green, lean and Six Sigma in service sector. Second, it supports and expands current literature, providing both academicians and practitioners a better panorama to understand the present status of L6σ for achieving sustainability in service sector.

  16. Intermittent hypoxia induces hyperlipidemia in lean mice.

    Science.gov (United States)

    Li, Jianguo; Thorne, Laura N; Punjabi, Naresh M; Sun, Cheuk-Kwan; Schwartz, Alan R; Smith, Philip L; Marino, Rafael L; Rodriguez, Annabelle; Hubbard, Walter C; O'Donnell, Christopher P; Polotsky, Vsevolod Y

    2005-09-30

    Obstructive sleep apnea, a syndrome leading to recurrent intermittent hypoxia (IH), has been associated previously with hypercholesterolemia, independent of underlying obesity. We examined the effects of experimentally induced IH on serum lipid levels and pathways of lipid metabolism in the absence and presence of obesity. Lean C57BL/6J mice and leptin-deficient obese C57BL/6J-Lep(ob) mice were exposed to IH for five days to determine changes in serum lipid profile, liver lipid content, and expression of key hepatic genes of lipid metabolism. In lean mice, exposure to IH increased fasting serum levels of total cholesterol, high-density lipoprotein (HDL) cholesterol, phospholipids (PLs), and triglycerides (TGs), as well as liver TG content. These changes were not observed in obese mice, which had hyperlipidemia and fatty liver at baseline. In lean mice, IH increased sterol regulatory element binding protein 1 (SREBP-1) levels in the liver, increased mRNA and protein levels of stearoyl-coenzyme A desaturase 1 (SCD-1), an important gene of TG and PL biosynthesis controlled by SREBP-1, and increased monounsaturated fatty acid content in serum, which indicated augmented SCD-1 activity. In addition, in lean mice, IH decreased protein levels of scavenger receptor B1, regulating uptake of cholesterol esters and HDL by the liver. We conclude that exposure to IH for five days increases serum cholesterol and PL levels, upregulates pathways of TG and PL biosynthesis, and inhibits pathways of cholesterol uptake in the liver in the lean state but does not exacerbate the pre-existing hyperlipidemia and metabolic disturbances in leptin-deficient obesity.

  17. Mobile Test Capabilities

    Data.gov (United States)

    Federal Laboratory Consortium — The Electrical Power Mobile Test capabilities are utilized to conduct electrical power quality testing on aircraft and helicopters. This capability allows that the...

  18. Study on laminar burning velocity of syngas-air premixed flames in various mixing conditions

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kee Man; Jeong, Byeong Gyu [Sunchon National University, Suncheon (Korea, Republic of); Lee, Seung Ro [Chonbuk National University, Jeonju (Korea, Republic of)

    2015-07-15

    The laminar burning velocity of syngas-air premixed flames was measured with various equivalence ratios from 0.5 to 5.0 and a mole fraction of H{sub 2} from 0.05 to 0.75. The laminar burning velocity was experimentally determined using a Bunsen flame according to the cone angle and surface area methods. A premixed code with a USC-II detailed reaction mechanism was used for the numerical calculations to predict the laminar burning velocity and to examine the relationship between the burning velocity enhancement and the hydrogen-related reactions. The results indicate that an appropriate method for the measurement of laminar burning velocity is necessary in the H{sub 2}/CO/air syngas premixed flame. In addition, the burning velocity linearly increased with the increase of the H{sub 2} mole fraction in the syngas mixture, although the burning velocity of H{sub 2} was 10 times larger than that of CO. This result is attributed to the rapid production of H-radicals at the early stage of combustion. Furthermore, the predicted mole fractions of H and OH radicals increased with the increase of H{sub 2} mole fraction for a lean syngas mixture. However, the mole fraction of OH radicals, an indicator of heat release rate, decreased for rich syngas mixture, resulting in a reduction of the laminar burning velocity, even with an increase of the H{sub 2} mole fraction.

  19. Study on laminar burning velocity of syngas-air premixed flames in various mixing conditions

    International Nuclear Information System (INIS)

    Lee, Kee Man; Jeong, Byeong Gyu; Lee, Seung Ro

    2015-01-01

    The laminar burning velocity of syngas-air premixed flames was measured with various equivalence ratios from 0.5 to 5.0 and a mole fraction of H 2 from 0.05 to 0.75. The laminar burning velocity was experimentally determined using a Bunsen flame according to the cone angle and surface area methods. A premixed code with a USC-II detailed reaction mechanism was used for the numerical calculations to predict the laminar burning velocity and to examine the relationship between the burning velocity enhancement and the hydrogen-related reactions. The results indicate that an appropriate method for the measurement of laminar burning velocity is necessary in the H 2 /CO/air syngas premixed flame. In addition, the burning velocity linearly increased with the increase of the H 2 mole fraction in the syngas mixture, although the burning velocity of H 2 was 10 times larger than that of CO. This result is attributed to the rapid production of H-radicals at the early stage of combustion. Furthermore, the predicted mole fractions of H and OH radicals increased with the increase of H 2 mole fraction for a lean syngas mixture. However, the mole fraction of OH radicals, an indicator of heat release rate, decreased for rich syngas mixture, resulting in a reduction of the laminar burning velocity, even with an increase of the H 2 mole fraction.

  20. An Experimental Investigation of Self-Excited Combustion Dynamics in a Single Element Lean Direct Injection (LDI) Combustor

    Science.gov (United States)

    Gejji, Rohan M.

    The management of combustion dynamics in gas turbine combustors has become more challenging as strict NOx/CO emission standards have led to engine operation in a narrow, lean regime. While premixed or partially premixed combustor configurations such as the Lean Premixed Pre-vaporized (LPP), Rich Quench Lean burn (RQL), and Lean Direct Injection (LDI) have shown a potential for reduced NOx emissions, they promote a coupling between acoustics, hydrodynamics and combustion that can lead to combustion instabilities. These couplings can be quite complex, and their detailed understanding is a pre-requisite to any engine development program and for the development of predictive capability for combustion instabilities through high-fidelity models. The overarching goal of this project is to assess the capability of high-fidelity simulation to predict combustion dynamics in low-emissions gas turbine combustors. A prototypical lean-direct-inject combustor was designed in a modular configuration so that a suitable geometry could be found by test. The combustor comprised a variable length air plenum and combustion chamber, air swirler, and fuel nozzle located inside a subsonic venturi. The venturi cross section and the fuel nozzle were consistent with previous studies. Test pressure was 1 MPa and variables included geometry and acoustic resonance, inlet temperatures, equivalence ratio, and type of liquid fuel. High-frequency pressure measurements in a well-instrumented metal chamber yielded frequencies and mode shapes as a function of inlet air temperature, equivalence ratio, fuel nozzle placement, and combustor acoustic resonances. The parametric survey was a significant effort, with over 105 tests on eight geometric configurations. A good dataset was obtained that could be used for both operating-point-dependent quantitative comparisons, and testing the ability of the simulation to predict more global trends. Results showed a very strong dependence of instability amplitude on

  1. Six sigma and lean production adoption in a manufacturing company

    Directory of Open Access Journals (Sweden)

    Alisson Christian Scheller

    2014-11-01

    Full Text Available The connection among Lean Production with Six Sigma originated the Lean Six Sigma methodology, focused on processes variation and waste reduction. This methodology was developed on different ways in the companies and there is no consensus over its structure and its implementation. In this context, this paper aims to identify and analyze the main characteristics on the adoption and integration of Lean Six Sigma methodology through a case study conducted in a manufacturing company that adopts lean production and six sigma. The results show two important aspects of the Lean Six Sigma methodology. One of them is the adoption of the value stream mapping as a central tool on Lean Six Sigma. The other is the use of DMAIC for improvements actions. The study indicates that despite the difficulties on Lean Six Sigma implementation, the methodology offers benefits to the company that adopts it in the suitable way.

  2. The Hybrid Lean System to Improve Manufacturing Environment

    Directory of Open Access Journals (Sweden)

    Ahmad Ahmad Nur Aizat

    2017-01-01

    Full Text Available Lean manufacturing is a systematic approch could increase manufacturing competitiveness by identifying and elminating waste through lean tools. However, these tools are often categorized into different groups, continues to be difficult for companies to select the most appropriate lean tool to be adopted, especially in respect of the SMEs whose knowledge of lean tools and associated principles are limited. This study is to propose solution on how to implement appropriate lean tools in food manufacturing industry located at Rengit, Johor. Qualitative method is used as a methodology to see the changes after the implementation of lean tools. Interview session also a part of method to collect data from respondents. The finding from this paper shows that implementation of an appropriate lean tool will help to eliminate waste in industry sector, maintain and control the inventory, improve quality of the product and improve overall operational process.

  3. Burning mouth disorder

    Directory of Open Access Journals (Sweden)

    Anand Bala

    2012-01-01

    Full Text Available Burning mouth disorder (BMD is a burning or stinging sensation affecting the oral mucosa, lips and/or tongue, in the absence of clinically visible mucosal lesions. There is a strong female predilection, with the age of onset being approximately 50 years. Affected patients often present with multiple oral complaints, including burning, dryness and taste alterations. The causes of BMD are multifactorial and remain poorly understood. Recently, there has been a resurgence of interest in this disorder with the discovery that the pain of burning mouth syndrome (BMS may be neuropathic in origin and originate both centrally and peripherally. The most common sites of burning are the anterior tongue, anterior hard palate and lower lip, but the distribution of oral sites affected does not appear to affect the natural history of the disorder or the response to treatment BMS may persist for many years. This article provides updated information on BMS and presents a new model, based on taste dysfunction, for its pathogenesis.

  4. Developing A Strategy to Enact Lean

    Directory of Open Access Journals (Sweden)

    Nicola Morrey

    2013-01-01

    Full Text Available This paper explains the strategy employed by a case study company to implement lean across the business, and to reflect on the success of this approach so other companies may consider this learning and how it might be useful to them. The strategy to enact lean in the case study company was based on creating a number of standard tools/ways of working. These tools can be considered to be standardised work for key aspects of the construction process that the company undertakes. The aim of the tools was to ensure that critical tasks would be carried out to the correct standard (quality, time, cost, health and safety every time, across the business. Achievement of this is expected to lead to improved performance and elimination of variation (waste. To implement this strategy of using standardised work to eliminate variation and lead to improved performance, a step-by-step process was developed to create the tools/standardised work. The paper describes the process that was undertaken and how it aimed to not only produce a number of tools/standardised work, but also to involve people and managers from across the business such that lean philosophy and thinking might also begin to become embedded. The paper will firstly explain, with reference to the relevant literature, how and why the strategy to implement standardised work was chosen, the process that was defined to develop the standardised work, and what happened when that process was put into practice. The findings of the paper show that whilst the completed tools delivered business benefits, the development of the tools did not follow the planned process. The paper discusses how people within the business responded to this strategy and how the process had to be continuously adapted to cope with the current business environment and path dependencies, further evidencing that lean implementations need to be tailored to suit the needs of the individual firm, rather than there being a one size fits all

  5. Sector Tests of a Low-NO(sub x), Lean, Direct- Injection, Multipoint Integrated Module Combustor Concept Conducted

    Science.gov (United States)

    Tacina, Robert R.; Wey, Chang-Lie; Laing, Peter; Mansour, Adel

    2002-01-01

    The low-emissions combustor development described is directed toward advanced high pressure aircraft gas-turbine applications. The emphasis of this research is to reduce nitrogen oxides (NOx) at high-power conditions and to maintain carbon monoxide and unburned hydrocarbons at their current low levels at low power conditions. Low-NOx combustors can be classified into rich-burn and lean-burn concepts. Lean-burn combustors can be further classified into lean-premixed-prevaporized (LPP) and lean direct injection (LDI) concepts. In both concepts, all the combustor air, except for liner cooling flow, enters through the combustor dome so that the combustion occurs at the lowest possible flame temperature. The LPP concept has been shown to have the lowest NOx emissions, but for advanced high-pressure-ratio engines, the possibility of autoignition or flashback precludes its use. LDI differs from LPP in that the fuel is injected directly into the flame zone, and thus, it does not have the potential for autoignition or flashback and should have greater stability. However, since it is not premixed and prevaporized, good atomization is necessary and the fuel must be mixed quickly and uniformly so that flame temperatures are low and NOx formation levels are comparable to those of LPP. The LDI concept described is a multipoint fuel injection/multiburning zone concept. Each of the multiple fuel injectors has an air swirler associated with it to provide quick mixing and a small recirculation zone for burning. The multipoint fuel injection provides quick, uniform mixing and the small multiburning zones provide for reduced burning residence time, resulting in low NOx formation. An integrated-module approach was used for the construction where chemically etched laminates, diffusion bonded together, combine the fuel injectors, air swirlers, and fuel manifold into a single element. The multipoint concept combustor was demonstrated in a 15 sector test. The configuration tested had 36

  6. Psychiatric aspects of burn

    Directory of Open Access Journals (Sweden)

    Dalal P

    2010-10-01

    Full Text Available Burn injuries and their subsequent treatment cause one of the most excruciating forms of pain imaginable. The psychological aspects of burn injury have been researched in different parts of the world, producing different outcomes. Studies have shown that greater levels of acute pain are associated with negative long-term psychological effects such as acute stress disorder, depression, suicidal ideation, and post-traumatic stress disorder for as long as 2 years after the initial burn injury. The concept of allostatic load is presented as a potential explanation for the relationship between acute pain and subsequent psychological outcomes. A biopsychosocial model is also presented as a means of obtaining better inpatient pain management and helping to mediate this relationship.

  7. Capabilities for Strategic Adaptation

    DEFF Research Database (Denmark)

    Distel, Andreas Philipp

    This dissertation explores capabilities that enable firms to strategically adapt to environmental changes and preserve competitiveness over time – often referred to as dynamic capabilities. While dynamic capabilities being a popular research domain, too little is known about what these capabiliti...

  8. Lean hydrous and anhydrous bioethanol combustion in spark ignition engine at idle

    International Nuclear Information System (INIS)

    Chuepeng, Sathaporn; Srisuwan, Sudecha; Tongroon, Manida

    2016-01-01

    Highlights: • Anhydrous ethanol burns fastest in uncalibrated engine at equal equivalence ratio. • The leaner hydrous ethanol combustion tends to elevate the COV in imep. • Hydrous ethanol consumption was 10% greater than anhydrous ethanol at ϕ = 0.67 limit. • Optimizing alternative fuel engine at idle for stability and emission is suggested. - Abstract: The applications of anhydrous bioethanol to substitute or replace gasoline fuel have shown to attain benefits in terms of engine thermal efficiency, power output and exhaust emissions from spark ignition engines. A hydrous bioethanol has also been gained more attention due to its energy and cost effectiveness. The main aim of this work is to minimize fuel quantity injected to the intake ports of a four-cylinder engine under idle condition. The engine running with hydrous ethanol undergoes within lean-burn condition as its combustion stability is analyzed using an engine indicating system. Coefficient of variation in indicated mean effective pressure is an indicator for combustion stability with hydrocarbon and carbon monoxide emission monitoring as a supplement. Anhydrous ethanol burns faster than hydrous ethanol and gasoline in the uncalibrated engine at the same fuel-to-air equivalence ratio under idle condition. The leaner hydrous ethanol combustion tends to elevate the coefficient of variation in indicated mean effective pressure. The experimental results have found that the engine consumes greater hydrous ethanol by 10% on mass basis compared with those of anhydrous ethanol at the lean limit of fuel-to-air equivalence ratio of 0.67. The results of exhaust gas analysis were compared with those predicted by chemical equilibrium analysis of the fuel-air combustion; the resemble trends were found. Calibrating the alternative fueled engine for fuel injection quantity should be accomplished at idle with combustion stability and emissions optimization.

  9. Lean Strategies in the Operating Room.

    Science.gov (United States)

    Robinson, Stephen T; Kirsch, Jeffrey R

    2015-12-01

    Lean strategies can be readily applied to health care in general and operating rooms specifically. The emphasis is on the patient as the customer, respect and engagement of all providers, and leadership from management. The strategy of lean is to use continuous improvement to eliminate waste from the care process, leaving only value-added activities. This iterative process progressively adds the steps of identifying the 7 common forms of waste (transportation, inventory, motion, waiting, overproduction, overprocessing, and defects), 5S (sort, simplify, sweep, standardize, sustain), visual controls, just-in-time processing, level-loaded work, and built-in quality to achieve the highest quality of patient care. Copyright © 2015 Elsevier Inc. All rights reserved.

  10. Network model of project "Lean Production"

    Science.gov (United States)

    Khisamova, E. D.

    2018-05-01

    Economical production implies primarily new approaches to culture of management and organization of production and offers a set of tools and techniques that allows reducing losses significantly and making the process cheaper and faster. Economical production tools are simple solutions that allow one to see opportunities for improvement of all aspects of the business, to reduce losses significantly, to constantly improve the whole spectrum of business processes, to increase significantly the transparency and manageability of the organization, to take advantage of the potential of each employee of the company, to increase competitiveness, and to obtain significant economic benefits without making large financial expenditures. Each of economical production tools solves a specific part of the problems, and only application of their combination will allow one to solve the problem or minimize it to acceptable values. The research of the governance process project "Lean Production" permitted studying the methods and tools of lean production and developing measures for their improvement.

  11. ["Lean management" in hospitals: potentials and limitations].

    Science.gov (United States)

    Glossmann, J P; Schliebusch, O; Diehl, V; Walshe, R

    2000-08-15

    Little attention has yet been payed on establishing modern and competitive organizational structures in German hospitals. In this paper, we attempt to apply elements of lean management to the work of physicians working in an inpatient setting. Traditional ways of communication and their disadvantages are discussed. These include loss of motivation, bureaucratic structures and a lack of interdisciplinary cooperation. Using Maslow's theory of motivation, possible improvements are discussed, such as the reduction of restrictive job characteristics, an increase of physicians' spheres of competence and the use of their innovative potentials. These suggestions are explained using practical examples. The aim of the study is to contribute to quality management in hospitals by increasing personal responsibilities according to lean management.

  12. Burning mouth syndrome

    Directory of Open Access Journals (Sweden)

    Sudha Jimson

    2015-01-01

    Full Text Available Burning mouth syndrome (BMS is a complex disorder that is characterized by warm or burning sensation in the oral mucosa without changes on physical examination. It occurs more commonly in middle-aged and elderly women and often affects the tip of the tongue, lateral borders, lips, hard and soft palate. This condition is probably of multi-factorial origin, often idiopathic, and its etiopathogensis is unknown. BMS can be classified into two clinical forms namely primary and secondary BMS. As a result, a multidisciplinary approach is required for better control of the symptoms. In addition, psychotherapy and behavioral feedback may also help eliminate the BMS symptoms.

  13. Biomass burning in Africa: As assessment of annually burned biomass

    International Nuclear Information System (INIS)

    Delmas, R.A.; Loudjani, P.; Podaire, A.; Menaut, J.C.

    1991-01-01

    It is now established that biomass burning is the dominant phenomenon that controls the atmospheric chemistry in the tropics. Africa is certainly the continent where biomass burning under various aspects and processes is the greatest. Three different types of burnings have to be considered-bush fires in savanna zones which mainly affect herbaceous flora, forest fires due to forestation for shifting agriculture or colonization of new lands, and the use of wood as fuel. The net release of carbon resulting from deforestation is assumed to be responsible for about 20% of the CO 2 increase in the atmosphere because the burning of forests corresponds to a destorage of carbon from the biospheric reservoir. The amount of reactive of greenhouse gases emitted by biomass burning is directly proportional, through individual emission factors, to the biomass actually burned. This chapter evaluates the biomass annually burned on the African continent as a result of the three main burning processes previously mentioned

  14. Simulation-enhanced lean design process

    Directory of Open Access Journals (Sweden)

    Jon H. Marvel

    2009-07-01

    Full Text Available 72 Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A traditional lean transformation process does not validate the future state before implementation, relying instead on a series of iterations to modify the system until performance is satisfactory. An enhanced lean process that includes future state validation before implementation is presented.  Simulation modeling and experimentation is proposed as the primary validation tool.  Simulation modeling and experimentation extends value stream mapping to include time, the behavior of individual entities, structural variability, random variability, and component interaction effects. Experiments to analyze the model and draw conclusions about whether the lean transformation effectively addresses the current state gap can be conducted.  Industrial applications of the enhanced lean process show it effectiveness.

  15. Where lean construction and value management meet

    OpenAIRE

    Musa, MM; Pasquire, C; Hurst, A

    2016-01-01

    The lean construction (LC) community’s key vision and goal is to provide value, yet they are increasingly challenged with understanding and dealing with the concept of value, with reports that value is one of the weakest points. Regardless of the previous studies and contributions already made on the concept of value in LC, the absence of a consistent understanding of value has resulted in misperceptions and indistinct boundaries with other construction value-related disciplines. Without a co...

  16. Dynamic capabilities, Marketing Capability and Organizational Performance

    Directory of Open Access Journals (Sweden)

    Adriana Roseli Wünsch Takahashi

    2017-01-01

    Full Text Available The goal of the study is to investigate the influence of dynamic capabilities on organizational performance and the role of marketing capabilities as a mediator in this relationship in the context of private HEIs in Brazil. As a research method we carried out a survey with 316 IES and data analysis was operationalized with the technique of structural equation modeling. The results indicate that the dynamic capabilities have influence on organizational performance only when mediated by marketing ability. The marketing capability has an important role in the survival, growth and renewal on educational services offerings for HEIs in private sector, and consequently in organizational performance. It is also demonstrated that mediated relationship is more intense for HEI with up to 3,000 students and other organizational profile variables such as amount of courses, the constitution, the type of institution and type of education do not significantly alter the results.

  17. Eradication of Productivity Related Problems Through Lean Principles In Integrated Manufacturing Environment

    Directory of Open Access Journals (Sweden)

    Rahul

    2013-06-01

    Full Text Available In this competitive era, manufacturing enterprises struggle to adopt cost-effective manufacturing systems. Overview of the recent manufacturing enterprises shows that successful global manufacturing enterprises have distributed their manufacturing capabilities over the globe. The successes of distributed integrated manufacturing enterprises depend upon the adaptation of appropriate manufacturing technologies like computer integrated manufacturing (CIM under the global collaborative environment along with the principles of lean manufacturing so that their corporate goals are achieved. CIM is an umbrella term which involves automated design, analysis, planning manufacturing, dispatching, customer-interaction, purchasing, cost accounting, inventory control and factory floor functions, which are inter-linked through the computer, to control all the campus-wide manufacturing related operations. It helps to improve the performance of a firm by integrating various areas of manufacturing business in which most of lean ideas are embedded. These lean ideas cause work in a process to be performed with minimum of non-value adding activities and focus on customers’ needs by delivering them at minimum time, with high quality and at minimum cost by eliminating hidden waste. What happens at the shop floor of even an integrated industry is that proper and timely attention is not paid to the intangible lean principles in the manual part of the CIM system which results in substantial loss of the plant productivity. Therefore the objective of this research paper is to investigate the different poor productivity-related problems in a partially integrated manufacturing environment and lay down the remedial measures to eradicate them using ‘Juran’s problem solving techniques’ and various ‘lean tools’ which results in the reduced wastages and hence improved productivity.

  18. Near-infrared spectroscopy assessment of microvasculature detects difference in lower limb vascular responsiveness in obese compared to lean individuals.

    Science.gov (United States)

    Soares, Rogério Nogueira; Murias, Juan M

    2018-07-01

    Microvascular dysfunction is an early complication in obesity-related cardiovascular disease (CVD) that can lead to changes in hemodynamic function and endothelial cell expression throughout the vasculature that is vessel specific. This study aimed to evaluate whether the near-infrared spectroscopy (NIRS) combined with a vascular occlusion (VOT) assessment was capable of detecting differences in vascular responsiveness within the microvasculature of the lower limb between lean and obese individuals. Twenty lean (BMI = 21.6 ± 1.3) and 17 obese individuals (BMI = 33.9 ± 1.1) participated in the study. Individuals underwent a VOT (5 min of baseline, 5 min of occlusion, and 8 min following cuff release) and vascular responsiveness was evaluated by the Slope 2 (Slope 2 StO 2 ) and the area under the curve (StO 2AUC ) of oxygen saturation (StO 2 ) signal during reperfusion. The difference between the minimal and the maximal value of StO 2 was calculated as the Amplitude of the StO 2 response. The Slope 2 StO 2 of the obese individuals was smaller (0.68 ± 0.07%·s -1 ) than the Slope 2 StO 2 of the lean individuals (1.08 ± 0.13%·s -1 ;P lean individuals (1708 ± 168%·s -1 ; P lean ones (30.4 ± 2.9 vs 21.6 ± 1.3 StO 2 (%), respectively; P lean individuals (r = 0.745; P lean and obese individuals. Copyright © 2018 Elsevier Inc. All rights reserved.

  19. Lean Production Practices to Enhance Organisational Performance

    Directory of Open Access Journals (Sweden)

    Shah Satya

    2017-01-01

    Full Text Available Service sector organisations are constantly overcoming the challenges facing the over-production and waste reduction within their environments. Industries are also becoming very competitive thus forcing them to seek suitable production organisation strategies with the aim towards enhancing their competitiveness and efficiency. The aim of this research study is to investigate the impact of lean production practices on the performance of service based businesses through the case study of a local baked goods supplier. The research framework adopted consists of questionnaire survey method implemented with different end users, thus covering the overall production – retail – customer cycle. The research results and analysis justify the objective of the research that lean production practices enhance the performance of the supplier company and the common tool identified were JIT (Just in Time, Value Steam Mapping (VSP and the 5S methods. The results also suggest that JIT method has a higher impact towards improvement on performance relating to quality, speed, dependability, flexibility and cost of the supplier. However, the research study also identifies that one of the major challenges faced by the organisation while adopting lean practices was the lack of commitment from top management, continuous training and employee engagement measures.

  20. Managing Waste Throughout Lean-Green Perspective

    Directory of Open Access Journals (Sweden)

    Lamyaa Mohammed Dawood

    2017-11-01

    Full Text Available Managing waste has been known as a crucial need as it may reduce resource consumption, rigid regulations regarded to the environment and occupational health and safety. Lean and green management are two approaches of management that validate waste. Since performance measures are crucial to improve waste management as its  goals of  to promote the performance of organizations .In this research four primary KPIs have been employed that are significant to lean-green management; operational, environmental, economic and social performance factors, subdivided further into sixteen as (Value stream mapping, life cycle assessment,---etc. Also in this research   determination and ranking of these performance measures and their influence on waste minimization is conducted. Interpretive Structural Modeling (ISM methodology is applied to the classification of Key Performance Indicators (KPIs according to the priority of their importance and the correlation between them and their impact to waste minimization. Cronbach’s Alpha coefficient is employed  to assess the reliability of performance measures to minimize waste, and increase customer  satisfaction.  Results showed that Al-Kufa Cement plant has bad overall performance toward lean green waste management perspective. The highest individual score is for operational performance (6.6 rated as medium. But  the lowest individual score is for economic performance [very bad (2.0].   

  1. [Surgical treatment of burns : Special aspects of pediatric burns].

    Science.gov (United States)

    Bührer, G; Beier, J P; Horch, R E; Arkudas, A

    2017-05-01

    Treatment of pediatric burn patients is very important because of the sheer frequency of burn wounds and the possible long-term ramifications. Extensive burns need special care and are treated in specialized burn centers. The goal of this work is to present current standards in burn therapy and important innovations in the treatment of burns in children so that the common and small area burn wounds and scalds in pediatric patients in day-to-day dermatological practice can be adequately treated. Analysis of current literature, discussion of reviews, incorporation of current guidelines. Burns in pediatric patients are common. Improvement of survival can be achieved by treatment in burn centers. The assessment of burn depth and area is an important factor for proper treatment. We give an overview for outpatient treatment of partial thickness burns. New methods may result in better long-term outcome. Adequate treatment of burn injuries considering current literature and guidelines improves patient outcome. Rational implementation of new methods is recommended.

  2. An assessment of burn care professionals' attitudes to major burn.

    LENUS (Irish Health Repository)

    Murphy, A D

    2008-06-01

    The resuscitation of severe burn remains a controversial area within the burn care profession. There is ongoing debate as to what percentage burn is associated with a sufficient quality of life to support initial resuscitation efforts. We conducted a survey of delegates at the 39th Annual Meeting of the British Burns Association (2005), regarding attitudes towards resuscitation following major burns. Respondents were asked the maximum percentage total body surface area (TBSA) burn beyond which they would not wish to be resuscitated. They were also asked what maximum TBSA they perceived to be commensurate with an acceptable quality of life (QOL). One hundred and forty three of 300 delegates responded to the questionnaire. Thirty three percent of respondents would not wish to be resuscitated with 50-75% TBSA burns or greater. A further 35% would not wish to have life-sustaining intervention with 75-95% TBSA burns or greater. The remaining 32% indicated that they would not want resuscitation with TBSA burns>95%. Regardless of TBSA affected, 16% would not wish resuscitation if they had full thickness facial burns, a further 10% did not want resuscitation if both their hands and faces were affected. Our survey demonstrates the diversity of personal preference amongst burn care professionals. This would suggest that a unifying philosophy regarding the resuscitation of extensive burns will remain elusive.

  3. [Nitrogen balance assessment in burn patients].

    Science.gov (United States)

    Beça, Andreia; Egipto, Paula; Carvalho, Davide; Correia, Flora; Oliveira, Bruno; Rodrigues, Acácio; Amarante, José; Medina, J Luís

    2010-01-01

    The burn injury probably represents the largest stimulus for muscle protein catabolism. This state is characterized by an accelerated catabolism of the lean or skeletal mass that results in a clinical negative balance of nitrogen and muscle wasting. The determination of an appropriate value for protein intake is essential, since it is positively related to the nitrogen balance (NB) and accordingly several authors argue that a positive NB is the key parameter associated with nutritional improvement of a burn patient. Evaluation of the degree of protein catabolism by assessment of the Nitrogen Balance; Defining of nutritional support (protein needs) to implement in patients with burned surface area (BSA) = 10%. We prospectively evaluated the clinical files and scrutinized the clinical variables of interest. The NB was estimated according to three formulae. Each gram of nitrogen calculated by the NB was then converted into grams of protein, subtracted or added to protein intake (or administered enteric or parenterically) and divided by kg of reference Weight (kg Rweight), in an attempt to estimate the daily protein needs. The cohort consisted of 10 patients, 6 females, with average age of 58(23) years old, a mean of BSA of 21.4(8.4)%, ranging from a minimum of 10.0% and máximum of 35.0%. On average, patients were 58 (23) years old. The average number of days of hospitalization in the burn unit was 64.8(36.5) days. We observed significant differences between the 3 methods used for calculating the NB (p = 0.004), on average the NB was positive. When the formula A was used the average value of NB was higher. Regarding the attempt to estimate the needs of g prot/kg Rweight/day most of the values did not exceed, on average, 2.6 g Prot/kg Rweight/day and no significant differences between patients with a BSA% of 10-20% and with BSA% > 20% were found. Despite being able to estimate the protein catabolism through these formulas and verifying that most values were above zero

  4. Minor burn - first aid - slideshow

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/presentations/100213.htm Minor burn - first aid - series—Procedure, part 1 To use ... out of 2 Overview To treat a minor burn, run cool water over the area of the ...

  5. [Burns in adolescents].

    Science.gov (United States)

    Ortiz Rodríguez, R; Domínguez Amillo, E; Soto Beauregard, C; Díaz González, M; López Gutiérrez, J C; Ros Mar, Z; Tovar Larrucea, J A

    2012-04-01

    The aim of this study was to know the epidemiology of burns in teenagers. Burn patients over 11 years old admitted in our Institution in the last 10 years were included. Etiology, burn size, hospital stay, quirurgical interventions and long term sequelae were registered. One thousand and eight patients were admitted, 89 were over 11 years (8.8%), 70.7% were boys and 29.3% girls. Fire was the principal agent in 58 cases (65.1%), due to fireworks in 13 (22.4%), alcohol in 7 (12%), explosion of flammable containers (spray) in 4 (6.8%) and gasoline in 3 (5.2%). Fireworks injuries and spray explosions affected face and hand in 88% cases. The median hospital stay was 8 days after admission (1 to 90). 83.1% required surgical treatment with mean of 1.8 +/- 1.4 interventions and 21.3% had long-term sequelaes that required at least one surgical intervention. Fire is the main cause of burns in adolescents. Fireworks injuries represented a quarter of that lesions, and highlights paint spray explosions as new causative agents. Considering the high morbidity in this age group, with permanent functional and aesthetic sequelae, prevention campaigns are needed to reduce such accidents.

  6. Electrical Burns: First Aid

    Science.gov (United States)

    ... local emergency number if the source of the burn is a high-voltage wire or lightning. Don't get near high-voltage ... 20 feet (about 6 meters) away — farther if wires are jumping and sparking. Don't move a person with ... breathing Heart rhythm problems (arrhythmias) Cardiac ...

  7. Burns - Multiple Languages

    Science.gov (United States)

    ... Translations Russian (Русский) Expand Section Burn Care - Русский (Russian) Bilingual ... Health Information Translations Characters not displaying correctly on this page? See language display issues . Return to the MedlinePlus Health Information ...

  8. One Burn, One Standard

    Science.gov (United States)

    2014-09-01

    PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Giretzlehner M., Haller H. L., Faucher L. D., Pressman M. A., Salinas J., Jeng J. C., 5d. PROJECT NUMBER 5e...AUVA Linz, Austria Lee D. Faucher, MD University of Wisconsin Madison, Wisconsin Melissa A. Pressman , PhD Arizona Burn Center Phoenix

  9. Inducible satellite cell depletion attenuates skeletal muscle regrowth following a scald-burn injury.

    Science.gov (United States)

    Finnerty, Celeste C; McKenna, Colleen F; Cambias, Lauren A; Brightwell, Camille R; Prasai, Anesh; Wang, Ye; El Ayadi, Amina; Herndon, David N; Suman, Oscar E; Fry, Christopher S

    2017-11-01

    Severe burns result in significant skeletal muscle cachexia that impedes recovery. Activity of satellite cells, skeletal muscle stem cells, is altered following a burn injury and likely hinders regrowth of muscle. Severe burn injury induces satellite cell proliferation and fusion into myofibres with greater activity in muscles proximal to the injury site. Conditional depletion of satellite cells attenuates recovery of myofibre area and volume following a scald burn injury in mice. Skeletal muscle regrowth following a burn injury requires satellite cell activity, underscoring the therapeutic potential of satellite cells in the prevention of prolonged frailty in burn survivors. Severe burns result in profound skeletal muscle atrophy; persistent muscle atrophy and weakness are major complications that hamper recovery from burn injury. Many factors contribute to the erosion of muscle mass following burn trauma, and we have previously shown concurrent activation and apoptosis of muscle satellite cells following a burn injury in paediatric patients. To determine the necessity of satellite cells during muscle recovery following a burn injury, we utilized a genetically modified mouse model (Pax7 CreER -DTA) that allows for the conditional depletion of satellite cells in skeletal muscle. Additionally, mice were provided 5-ethynyl-2'-deoxyuridine to determine satellite cell proliferation, activation and fusion. Juvenile satellite cell-wild-type (SC-WT) and satellite cell-depleted (SC-Dep) mice (8 weeks of age) were randomized to sham or burn injury consisting of a dorsal scald burn injury covering 30% of total body surface area. Both hindlimb and dorsal muscles were studied at 7, 14 and 21 days post-burn. SC-Dep mice had >93% depletion of satellite cells compared to SC-WT (P satellite cell proliferation and fusion. Depletion of satellite cells impaired post-burn recovery of both muscle fibre cross-sectional area and volume (P satellite cells in the aetiology of lean

  10. Lean-Prinzipien für verbesserte Kosteneffizienz: Instandhaltungseffizienz durch Lean Maintenance

    OpenAIRE

    Bandow, G.; Schmidt, A.

    2008-01-01

    Die Bedeutung der Instandhaltung nimmt weiter zu. In einem Lean Umfeld mit einer immer verschwendungsärmeren Produktion stehen nicht nur die Kosteneffizienz und Verfügbarkeit der Produktionsmittel im Fokus. Unplanmäßige Stillstände kosten Geld und gefährden häufig auch Personal und Produkt. Lean Maintenance vermeidet Verschwendung und optimiert so die Effektivität und Effizienz der Instandhaltung. Das zielgerichtete Zusammenspiel von Menschen, Prozessen und Technik garantiert dabei den Erfolg...

  11. Lean Thinking and Transferring Lean Management - The Best Defence against an Economic Recession?

    Directory of Open Access Journals (Sweden)

    Daniel D. GEORGESCU

    2011-06-01

    Full Text Available Productivity growth is a fundamental means for society to improve its living standards. Productivity growth comes from technological change (new ways of producing goods and services and better organisation of production (better ways of using available resources given available technology. Both processes operate simultaneously and, in practice, it is difficult to distinguish between the effects of each process. The processes are dynamic and affect individual activities differently over time. These years, manufacturing functions have been transferred rapidly and globally from mature countries to emerging countries. This paper is about the lean philosophy and the critical elements for successful transfer of lean management among sites and countries.

  12. Burn Wise Educational Materials for Businesses

    Science.gov (United States)

    Burn Wise outreach material. Burn Wise is a partnership program of that emphasizes the importance of burning the right wood, the right way, in the right wood-burning appliance to protect your home, health, and the air we breathe.

  13. Repeated Prescribed Burning in Aspen

    Science.gov (United States)

    Donald A. Perala

    1974-01-01

    Infrequent burning weather, low flammability of the aspen-hardwood association, and prolific sprouting and seeding of shrubs and hardwoods made repeated dormant season burning a poor tool to convert good site aspen to conifers. Repeat fall burns for wildlife habitat maintenance is workable if species composition changes are not important.

  14. Air-Freshener Burns: A New Paradigm in Burns Etiology?

    OpenAIRE

    Sarwar, Umran; Nicolaou, M.; Khan, M. S.; Tiernan, E.

    2011-01-01

    Objectives: We report a rare case of burns following the use of automated air-fresheners. Methods: We present a case report with a brief overview of the literature relating to burns associated with air-fresheners. The mechanism and treatment of these types of injuries are also described. Results: A 44 year-old female was admitted under the care of the burns team following burns secondary to an exploding air-freshener canister. The patient sustained burns to the face, thorax and arms re...

  15. Performance effect of multiple control forms in a Lean organization

    DEFF Research Database (Denmark)

    Kristensen, Thomas Borup; Israelsen, Poul

    2012-01-01

    Over the last decades Lean has developed into a prominent management philosophy reaching beyond shop floor tools. However, substantial support of performance effects from Lean is still scarce and at best with mixed results. Recently, research has turned its focus towards perceiving Lean...... as a control package. In this paper we present statistical support for enhanced performance coming from Lean. Furthermore, our results strongly support the perception of Lean as a set of multiple control forms (output, behavioral, and social controls) that complement each other. Therefore, performance...... is increased if the average level of control forms is increased, and performance is further increased if the control forms are balanced at the same level representing a complementary effect between them. Our data are archival data spanning multiple years in a strong Lean organization. The dependent performance...

  16. Lean Management Systems in Radiology: Elements for Success.

    Science.gov (United States)

    Schultz, Stacy R; Ruter, Royce L; Tibor, Laura C

    2016-01-01

    This article is a review of the literature on Lean and Lean Management Systems and how they have been implemented in healthcare organizations and particularly in radiology departments. The review focuses on the elements required for a successful implementation of Lean by applying the principles of a Lean Management System instead of a Lean tools-only approach. This review shares the successes and failures from healthcare organizations' efforts to improve the quality and safety of the services they provide. There are a limited number of healthcare organizations in the literature who have shared their experiences and additional research is necessary to determine whether a Lean Management System is a viable alternative to the current management structure in healthcare.

  17. Is proportion burned severely related to daily area burned?

    International Nuclear Information System (INIS)

    Birch, Donovan S; Morgan, Penelope; Smith, Alistair M S; Kolden, Crystal A; Hudak, Andrew T

    2014-01-01

    The ecological effects of forest fires burning with high severity are long-lived and have the greatest impact on vegetation successional trajectories, as compared to low-to-moderate severity fires. The primary drivers of high severity fire are unclear, but it has been hypothesized that wind-driven, large fire-growth days play a significant role, particularly on large fires in forested ecosystems. Here, we examined the relative proportion of classified burn severity for individual daily areas burned that occurred during 42 large forest fires in central Idaho and western Montana from 2005 to 2007 and 2011. Using infrared perimeter data for wildfires with five or more consecutive days of mapped perimeters, we delineated 2697 individual daily areas burned from which we calculated the proportions of each of three burn severity classes (high, moderate, and low) using the differenced normalized burn ratio as mapped for large fires by the Monitoring Trends in Burn Severity project. We found that the proportion of high burn severity was weakly correlated (Kendall τ = 0.299) with size of daily area burned (DAB). Burn severity was highly variable, even for the largest (95th percentile) in DAB, suggesting that other variables than fire extent influence the ecological effects of fires. We suggest that these results do not support the prioritization of large runs during fire rehabilitation efforts, since the underlying assumption in this prioritization is a positive relationship between severity and area burned in a day. (letters)

  18. Actinide burning and waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Pigford, T H [University of California, Berkeley, CA (United States)

    1990-07-01

    Here we review technical and economic features of a new proposal for a synergistic waste-management system involving reprocessing the spent fuel otherwise destined for a U.S. high-level waste repository and transmuting the recovered actinides in a fast reactor. The proposal would require a U.S. fuel reprocessing plant, capable of recovering and recycling all actinides, including neptunium americium, and curium, from LWR spent fuel, at recoveries of 99.9% to 99.999%. The recovered transuranics would fuel the annual introduction of 14 GWe of actinide-burning liquid-metal fast reactors (ALMRs), beginning in the period 2005 to 2012. The new ALMRs would be accompanied by pyrochemical reprocessing facilities to recover and recycle all actinides from discharged ALMR fuel. By the year 2045 all of the LWR spent fuel now destined f a geologic repository would be reprocessed. Costs of constructing and operating these new reprocessing and reactor facilities would be borne by U.S. industry, from the sale of electrical energy produced. The ALMR program expects that ALMRs that burn actinides from LWR spent fuel will be more economical power producers than LWRs as early as 2005 to 2012, so that they can be prudently selected by electric utility companies for new construction of nuclear power plants in that era. Some leaders of DOE and its contractors argue that recovering actinides from spent fuel waste and burning them in fast reactors would reduce the life of the remaining waste to about 200-300 years, instead of 00,000 years. The waste could then be stored above ground until it dies out. Some argue that no geologic repositories would be needed. The current view expressed within the ALMR program is that actinide recycle technology would not replace the need for a geologic repository, but that removing actinides from the waste for even the first repository would simplify design and licensing of that repository. A second geologic repository would not be needed. Waste now planned

  19. Actinide burning and waste disposal

    International Nuclear Information System (INIS)

    Pigford, T.H.

    1990-01-01

    Here we review technical and economic features of a new proposal for a synergistic waste-management system involving reprocessing the spent fuel otherwise destined for a U.S. high-level waste repository and transmuting the recovered actinides in a fast reactor. The proposal would require a U.S. fuel reprocessing plant, capable of recovering and recycling all actinides, including neptunium americium, and curium, from LWR spent fuel, at recoveries of 99.9% to 99.999%. The recovered transuranics would fuel the annual introduction of 14 GWe of actinide-burning liquid-metal fast reactors (ALMRs), beginning in the period 2005 to 2012. The new ALMRs would be accompanied by pyrochemical reprocessing facilities to recover and recycle all actinides from discharged ALMR fuel. By the year 2045 all of the LWR spent fuel now destined f a geologic repository would be reprocessed. Costs of constructing and operating these new reprocessing and reactor facilities would be borne by U.S. industry, from the sale of electrical energy produced. The ALMR program expects that ALMRs that burn actinides from LWR spent fuel will be more economical power producers than LWRs as early as 2005 to 2012, so that they can be prudently selected by electric utility companies for new construction of nuclear power plants in that era. Some leaders of DOE and its contractors argue that recovering actinides from spent fuel waste and burning them in fast reactors would reduce the life of the remaining waste to about 200-300 years, instead of 00,000 years. The waste could then be stored above ground until it dies out. Some argue that no geologic repositories would be needed. The current view expressed within the ALMR program is that actinide recycle technology would not replace the need for a geologic repository, but that removing actinides from the waste for even the first repository would simplify design and licensing of that repository. A second geologic repository would not be needed. Waste now planned

  20. Analysis The Leanness of The Supply Chain By Fuzzy QFD

    OpenAIRE

    Mukesh Singh Baghel; Pavan Agrawal

    2014-01-01

    The new systems of doing business in manufacturing have evolved in recent decades Lean production. Lean production can be traced to the 1960s in Japan, when Toyota Motors started innovating changes in mass production to deal with its domestic automotive market. The term “Lean production” was coined around 1989 with the popularity of the book, the machine that can change the world written by researchers at the Massachusetts Institute of Technology (MIT). The term itself was coined ...

  1. Application of lean manufacturing techniques in the Emergency Department.

    Science.gov (United States)

    Dickson, Eric W; Singh, Sabi; Cheung, Dickson S; Wyatt, Christopher C; Nugent, Andrew S

    2009-08-01

    "Lean" is a set of principles and techniques that drive organizations to continually add value to the product they deliver by enhancing process steps that are necessary, relevant, and valuable while eliminating those that fail to add value. Lean has been used in manufacturing for decades and has been associated with enhanced product quality and overall corporate success. To evaluate whether the adoption of Lean principles by an Emergency Department (ED) improves the value of emergency care delivered. Beginning in December 2005, we implemented a variety of Lean techniques in an effort to enhance patient and staff satisfaction. The implementation followed a six-step process of Lean education, ED observation, patient flow analysis, process redesign, new process testing, and full implementation. Process redesign focused on generating improvement ideas from frontline workers across all departmental units. Value-based and operational outcome measures, including patient satisfaction, expense per patient, ED length of stay (LOS), and patient volume were compared for calendar year 2005 (pre-Lean) and periodically after 2006 (post-Lean). Patient visits increased by 9.23% in 2006. Despite this increase, LOS decreased slightly and patient satisfaction increased significantly without raising the inflation adjusted cost per patient. Lean improved the value of the care we delivered to our patients. Generating and instituting ideas from our frontline providers have been the key to the success of our Lean program. Although Lean represents a fundamental change in the way we think of delivering care, the specific process changes we employed tended to be simple, small procedure modifications specific to our unique people, process, and place. We, therefore, believe that institutions or departments aspiring to adopt Lean should focus on the core principles of Lean rather than on emulating specific process changes made at other institutions.

  2. A new lean change methodology for small & medium sized enterprises

    OpenAIRE

    April, Joris; Powell, Daryl; Bart, Schanssema

    2010-01-01

    SMEs find it difficult to implement productivity improvement tools, particularly those associated with Lean Manufacturing. Larger companies have more success due to greater access to resources. To provide the SMEs with a way to implement Lean sustainably, the European project ERIP develops a new lean change methodology for SMEs. In this paper the methodology is explained and three test cases show the strength of the methodology. The method is a sequence of achieving management and company sup...

  3. Lean and Efficient Software: Whole-Program Optimization of Executables

    Science.gov (United States)

    2015-09-30

    Lean and Efficient Software: Whole-Program Optimization of Executables” Project Summary Report #5 (Report Period: 7/1/2015 to 9/30/2015...TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Lean and Efficient Software: Whole-Program Optimization of Executables 5a...unclassified c. THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 Lean and Efficient Software: Whole-Program

  4. A Model to align the organizational culture to Lean

    Directory of Open Access Journals (Sweden)

    Mehrsa Taherimashhadi

    2018-04-01

    Full Text Available Purpose: Since the emergence of Lean Manufacturing many organizations strived to implement it. Nonetheless, sustainable Lean transformation is not as easy as to be simply achieved. Several aspects need to be taken into account before Lean implementation which national and organizational culture are important. By considering influences of national culture on the organizational culture, this paper aims at proposing an evaluation model to determine the cultural weaknesses of an organization and give some recommendations to manage people before implementing Lean. Design/methodology/approach: This research has been conducted based on literature review survey and semi-structured interviews. Research papers, conference proceedings, books, and official websites regarding Lean philosophy were reviewed to find the influence of national culture in Lean implementation. Different databases were scrutinized, from 2015 to 2017, containing Scopus and Web of Science with the time period of 1996-2016. A set of key terms and their combinations were used including: Toyota Production system, Lean production, Lean manufacturing, Lean management, Transformation, Implementation, Barriers/ Impediments/Challenges/Difficulties, Human resources, Success factors, Organizational culture, and National culture. Findings: The proposed evaluation model is a guide for organizations to determine cultural misalignments between the corporate culture and the Lean culture before its implementation and gives some managerial recommendations to correct them. Originality/value: This study is the first attempt to integrate the national models   with Lean culture to provide an evaluation model and some recommendations to help the organization to align its culture to Lean culture before its implementation.

  5. Implementing lean office: a successful case in public sector

    OpenAIRE

    Monteiro, Mónica F. J. R.; Pacheco, Claudia C. L.; Dinis-Carvalho, José; Paiva, Francisco C.

    2015-01-01

    Applying lean approaches in office areas can lead to performance improvements and other benefits as achieved in traditional manufacturing environments. The intangibility of office operations may appear as a major difficulty for lean implementations but in fact the benefits achievable are as important as the ones achieved in manufacturing environments. This paper reports a successful case of lean office implementation in a public sector organization giving emphasis to its major performance imp...

  6. Identification of Lean Implementation Hurdles in Indian Industries

    OpenAIRE

    Bhim Singh

    2016-01-01

    Due to increased pressure from global competitors, manufacturing organizations are switching over to lean philosophies from traditional mass production. Lean manufacturing is a manufacturing philosophy which focuses on elimination of various types of wastes and creates maximum value for the end customers. Lean thinking aims to produce high quality products and services at the lowest possible cost with maximum customer responsiveness. Indian Industry is facing lot of problems in this transform...

  7. Air-freshener burns: a new paradigm in burns etiology?

    Science.gov (United States)

    Sarwar, Umran; Nicolaou, M; Khan, M S; Tiernan, E

    2011-10-01

    We report a rare case of burns following the use of automated air-fresheners. We present a case report with a brief overview of the literature relating to burns associated with air-fresheners. The mechanism and treatment of these types of injuries are also described. A 44 year-old female was admitted under the care of the burns team following burns secondary to an exploding air-freshener canister. The patient sustained burns to the face, thorax and arms resulting in a seven-day hospital admission. The burns were treated conservatively. To our knowledge this is one of the few documented cases of burns as a result of air-fresheners. As they become more ubiquitous, we anticipate the incidence of such cases to increase. As such, they pose a potential public health concern on a massive scale.

  8. Gas chromatographic determination of Di-n-butyl phosphate in radioactive lean organic solvent of FBTR carbide fuel reprocessing

    International Nuclear Information System (INIS)

    Velavendan, P.; Ganesh, S.; Pandey, N.K.; Kamachi Mudali, U.; Natarajan, R.

    2011-01-01

    In the present work Di-n- butyl phosphate (DBP) a degraded product of Tri-n-butyl phosphate (TBP) formed by acid hydrolysis and radiolysis in the PUREX process was analyzed. Lean organic streams of different fuel burn-up FBTR carbide fuel reprocessing solution was determined by standard Gas Chromatographic technique. The method involves the conversion of non-volatile Di-n-butyl phosphate into volatile and stable derivatives by the action of diazomethane and then determined by Gas Chromatograph (GC). A calibration graph was made for DBP concentration range of 200-2000 ppm with correlation coefficient of 0.99587 and RSD 1.2 %. (author)

  9. Getting 'Lean': hardwiring process excellence into Northeast Health.

    Science.gov (United States)

    Brown, Tricia; Duthe, Robert

    2009-01-01

    Many healthcare organizations are turning to the "Lean" Toyota Production System as a means to hardwire process excellence into their organizations. Northeast Health, an integrated delivery system in New York's capital region, introduced the Lean concept into its culture in 2004. After four years, the organization is beginning to see its staff hardwire Lean thinking into day-to-day behaviors. This paper focuses on the approach used by Northeast Health to introduce Lean concepts into its culture, challenges faced, lessons learned and the factors critical to success.

  10. Application of a mathematical model for ergonomics in lean manufacturing.

    Science.gov (United States)

    Botti, Lucia; Mora, Cristina; Regattieri, Alberto

    2017-10-01

    The data presented in this article are related to the research article "Integrating ergonomics and lean manufacturing principles in a hybrid assembly line" (Botti et al., 2017) [1]. The results refer to the application of the mathematical model for the design of lean processes in hybrid assembly lines, meeting both the lean principles and the ergonomic requirements for safe assembly work. Data show that the success of a lean strategy is possible when ergonomics of workers is a parameter of the assembly process design.

  11. Lean leadership attributes: a systematic review of the literature.

    Science.gov (United States)

    Aij, Kjeld Harald; Teunissen, Maurits

    2017-10-09

    Purpose Emphasis on quality and reducing costs has led many health-care organizations to reconfigure their management, process, and quality control infrastructures. Many are lean, a management philosophy with roots in manufacturing industries that emphasizes elimination of waste. Successful lean implementation requires systemic change and strong leadership. Despite the importance of leadership to successful lean implementation, few researchers have probed the question of ideal leadership attributes to achieve lean thinking in health care. The purpose of this paper is to provide insight into applicable attributes for lean leaders in health care. Design/methodology/approach The authors systematically reviewed the literature on principles of leadership and, using Dombrowski and Mielke's (2013) conceptual model of lean leadership, developed a parallel theoretical model for lean leadership in health care. Findings This work contributes to the development of a new framework for describing leadership attributes within lean management of health care. Originality/value The summary of attributes can provide a model for health-care leaders to apply lean in their organizations.

  12. Using lean methodologies for economically and environmentally sustainable foundries

    Directory of Open Access Journals (Sweden)

    R. M. Torielli

    2011-02-01

    Full Text Available Lean manufacturing is often seen as a set of tools that reduce the total cost and improve the quality of manufactured products. The lean management philosophy is one which targets waste reduction in every facet of the manufacturing business; however, only recently have studies linked lean management philosophies with improving environmental sustainability. These studies suggest that lean manufacturing is more than a set of lean tools that can optimize manufacturing efficiencies; it is a process and mindset that needs to be integrated into daily manufacturing systems to achieve sustainability. The foundry industry, as well as manufacturing in general, has significant challenges in the current regulatory and political climate with developing an economically and environmentally sustainable business model. Lean manufacturing has proven itself as a model for both economic sustainability and environmental stewardship. Several recent studies have shown that both lean and green techniques and “zero-waste” policies also lead to reductions in overall cost. While these strategies have been examined for general manufacturing, they have not been investigated in detail for the foundry industry. This paper will review the current literature and describe how lean and green can provide a relevant framework for environmentally and economically sustainable foundries. Examples of lean and green technologies and techniques which can be applied to foundries in a global context will be described.

  13. LEAN ACCOUNTING: SUATU ALTERNATIF TEKNIK AKUNTANSI MANAJEMEN DALAM INDUSTRI MANUFAKTUR

    Directory of Open Access Journals (Sweden)

    Eka Ardhani Sisdyani

    2010-07-01

    Full Text Available Manufacturing techniques have been developed to embrace theaims of continuous improvement. Continuous improvement would leadcompanies to win business competition. One technique that gains moreand more followers is lean manufacturing. Lean manufacturing hastwo main purposes, which are eliminating wastes and creating valuesto customers. It focuses on customer values, value stream, productionflows, demand-pull, and perfection. Lean accounting is needed tosupport and encourage the development of lean manufacturing, forinstances in product costing system, external reporting, and otherdecision making processes that need accounting data.

  14. Why Lean doesn't work for everyone.

    Science.gov (United States)

    Kaplan, Gary S; Patterson, Sarah H; Ching, Joan M; Blackmore, C Craig

    2014-12-01

    Popularisation of Lean in healthcare has led to emphasis on Lean quality improvement tools in isolation, with inconsistent results. We argue that delivery of safer, more efficient, and higher quality-patient focused care requires organisational transformation of which the Lean toolkit is only one component. To successfully facilitate system transformation toward higher quality care at lower cost, Lean tools must be part of a comprehensive management system, within a supportive institutional culture, and with committed leadership. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  15. Prevalence and hemodynamic effects of leaning during CPR

    Science.gov (United States)

    Niles, Dana E.; Sutton, Robert M.; Nadkarni, Vinay M.; Glatz, Andrew; Zuercher, Mathias; Maltese, Matthew R.; Eilevstjønn, Joar; Abella, Benjamin S.; Becker, Lance B.; Berg, Robert A.

    2013-01-01

    Background Cardiopulmonary resuscitation (CPR) guidelines recommend complete release between chest compressions (CC). Objective Evaluate the hemodynamic effects of leaning (incomplete chest wall release) during CPR and the prevalence of leaning during CPR. Results In piglet ventricular fibrillation cardiac arrests, 10% and 20% (1.8 kg and 3.6 kg, respectively), leaning during CPR increased right atrial pressures, decreased coronary perfusion pressures, and decreased cardiac index and left ventricular myocardial blood flow by nearly 50%. In contrast, residual leaning of a 260 g accelerometer/ force feedback device did not adversely affect cardiac index or myocardial blood flow. Among 108 adult in-hospital CPR events, leaning ≥2.5 kg was demonstrable in 91% of the events and 12% of the evaluated CC. For 12 children with in-hospital CPR, 28% of CC had residual leaning ≥2.5 kg and 89% had residual leaning ≥0.5 kg. Conclusions Leaning during CPR increases intrathoracic pressure, decreases coronary perfusion pressure, and decreases cardiac output and myocardial blood flow. Leaning is common during CPR. PMID:22208173

  16. What Determines Lean Manufacturing Implementation? A CB-SEM Model

    Directory of Open Access Journals (Sweden)

    Tan Ching Ng

    2018-02-01

    Full Text Available This research aims to ascertain the determinants of effective Lean Manufacturing (LM. In this research, Covariance-based Structural Equation Modeling (CB-SEM analysis will be used in order to analyze the determinants. Through CB-SEM analysis, the significant key determinants can be determined and the direct relationships among determinants can be analyzed. Thus, the findings of this research can act as guidelines for achievement of LM effectiveness, not only providing necessary steps for successful implementation of lean, but also helping lean companies to achieve higher level of lean cost and time savings.

  17. Experienced Barriers to Lean in Swedish Manufacturing and Health Care

    Directory of Open Access Journals (Sweden)

    Bengt Halling

    2013-12-01

    Full Text Available The purpose is to compare similarities and divergences in how the concepts of Lean and barriers to Lean are described by key informants at a production unit in a large manufacturing company and two emergency health care units in Sweden. Data was collected via semi-structured interviews and analyzed with the constant comparative method (CCM and Porras and Robertson’s (1992 change model. : In both organizations, the view of Lean changed from a toolbox to a human behavior view. Eight barriers were experienced in both organizations. Three barriers were unique to manufacturing or to health care, respectively. Nine barriers were elements of social factors; five were elements of organizing arrangements. Only people practically involved and responsible for the implementation at the two organizations participated in the study. Persons responsible for implementing Lean should consider organizational arrangements and social factors in order to limit barriers to successful implementation. Most research on Lean has been about successful Lean implementations. This study focuses on how Lean is viewed and what barriers personnel in manufacturing and health care have experienced. In comparing the barriers to Lean experienced in the two groups, common, archetypical, and unique barriers for manufacturing and health care can be identified, thus contributing to knowledge about barriers to Lean implementation.

  18. Product innovation and commercialization in lean global start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

  19. Lean principles adoption in environmental management system (EMS - ISO 14001

    Directory of Open Access Journals (Sweden)

    Perumal Puvanasvaran

    2012-12-01

    Full Text Available Purpose: The purpose of this study is to examine the characteristic of the lean principles into ISO 14001 and to propose linkage of the lean principles and ISO 14001.Design/methodology/approach: To achieve the objective of the study, literature survey and quantitative research method using questionnaires survey are used.Findings and Originality/value: The findings of this study confirm that ISO 14001 certified company adopted lean production practices.  The study also proves that lean principles have positive and significant relationship with ISO 14001 EMS and the linkage can be made between lean principles and ISO 14001 to achieve Continual Improvement.Research limitations/implications: The small sizes of the sample of the participating companies are the main limitations of this study and this research mainly focuses on the manufacturing environment and services industry.Practical implications: This research show that all ISO 14001 companies do adopt at least one lean production practices and the main findings are lean principles has positive and highly significant relationship with ISO 14001 requirements.  This is because the integration of lean principles into ISO 14001 will serve practical methods for ISO14001 EMS to achieve the continual improvement.Originality/value: This research is amongst the first to study the combined lean principles with ISO 1400.  Based on the current situation, there is no integration within this two management system. 

  20. Biomass Burning Emissions from Fire Remote Sensing

    Science.gov (United States)

    Ichoku, Charles

    2010-01-01

    Knowledge of the emission source strengths of different (particulate and gaseous) atmospheric constituents is one of the principal ingredients upon which the modeling and forecasting of their distribution and impacts depend. Biomass burning emissions are complex and difficult to quantify. However, satellite remote sensing is providing us tremendous opportunities to measure the fire radiative energy (FRE) release rate or power (FRP), which has a direct relationship with the rates of biomass consumption and emissions of major smoke constituents. In this presentation, we will show how the satellite measurement of FRP is facilitating the quantitative characterization of biomass burning and smoke emission rates, and the implications of this unique capability for improving our understanding of smoke impacts on air quality, weather, and climate. We will also discuss some of the challenges and uncertainties associated with satellite measurement of FRP and how they are being addressed.

  1. Lean management - an effective way to arrange maintenance?; Lean Management - ein effektiver Weg zur Gestaltung der Instandhaltung?

    Energy Technology Data Exchange (ETDEWEB)

    Tschuschke, W. [Inst. fuer Instandhaltung gGmbH, Iserlohn (Germany)

    1996-08-01

    Lean management/lean production wishes to attain more through intelligent operation system/production at less expense (personnel, materials, energy, costs). The object is not harder but more intelligent and production work; we do not need to run faster but to find shorter routes. The idea of lean management`s effects and changes have consequences for the field of maintenance as an equivalent and legitimate business area which are discussed in this paper. (orig.) [Deutsch] Lean Management/Lean Production will durch ein intelligentes Arbeitssystem/Produzieren mit weniger Aufwand (Personal, Material, Energie, Kosten) mehr erreichen. Ziel ist nicht das haertere, sondern das intelligentere und produktivere Arbeiten; wir sollen nicht schneller laufen, sondern kuerzere Wege finden. Fuer den Bereich Instandhaltung als gleichwertiger und gleichberechtigter Unternehmensbereich haben die Gedanken des Lean Managements Auswirkungen und Veraenderungen zur Folge, die im Beitrag genannt werden. (orig.)

  2. Leaning on lean: the reception of a management fashion in Germany

    NARCIS (Netherlands)

    Benders, J.G.J.M.; Bijsterveld, M.J.L. van

    2000-01-01

    The ‘fashionable’ concept of lean production has been discussed more intensively in Germany than elsewhere in Europe but has resulted not only in rationalisation measures such as downsizing and delayering but also in implementing ‘Gruppenarbeit’. Through interpretation processes at different levels,

  3. "The largest Lean transformation in the world": the implementation and evaluation of lean in Saskatchewan healthcare.

    Science.gov (United States)

    Kinsman, Leigh; Rotter, Thomas; Stevenson, Katherine; Bath, Brenna; Goodridge, Donna; Harrison, Liz; Dobson, Roy; Sari, Nazmi; Jeffery, Cathy; Bourassa, Carrie; Westhorp, Gill

    2014-01-01

    The Saskatchewan Ministry of Health has committed to a multi-million dollar investment toward the implementation of Lean methodology across the province's healthcare system. Originating as a production line discipline (the Toyota Production System), Lean has evolved to encompass process improvements including inventory management, waste reduction and quality improvement techniques. With an initial focus on leadership, strategic alignment, training and the creation of a supportive infrastructure (Lean promotion offices), the goal in Saskatchewan is a whole health system transformation that produces "better health, better value, better care, and better teams." Given the scope and scale of the initiative and the commitment of resources, it is vital that a comprehensive, longitudinal evaluation plan be implemented to support ongoing decision-making and program design. The nature of the initiative also offers a unique opportunity to contribute to health quality improvement science by advancing our understanding of the implementation and evaluation of complex, large-scale healthcare interventions. The purpose of this article is to summarize the background to Lean in Saskatchewan and the proposed evaluation methods. Copyright © 2014 Longwoods Publishing.

  4. Lean Architecture for Agile Software Development

    CERN Document Server

    Coplien, James O

    2010-01-01

    More and more Agile projects are seeking architectural roots as they struggle with complexity and scale - and they're seeking lightweight ways to do it: Still seeking? In this book the authors help you to find your own path; Taking cues from Lean development, they can help steer your project toward practices with longstanding track records; Up-front architecture? Sure. You can deliver an architecture as code that compiles and that concretely guides development without bogging it down in a mass of documents and guesses about the implementation; Documentation? Even a whiteboard diagram, or a CRC

  5. ANFO truck burn trials

    Energy Technology Data Exchange (ETDEWEB)

    Rosen von, B.; Contestabile, E. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2003-10-01

    This report describes the investigation of a tractor-trailer explosion. A truck loaded with 18,000 kg of commercial explosives, of which 13,000 kg was ammonium nitrate with fuel oil (ANFO), caught fire when it struck a rockcut near Walden, Ontario on August 5, 1998. The fire resulted in the detonation of the load. The Canadian Explosives Research Laboratory (CERL) conducted a test program to examine the suitability of existing explosive transportation regulations. Unconfined burns of ANFO were performed. The accident was recreated in two burn trials in an attempt to identify the mechanism that led from fire to detonation. Two full-scale tests were conducted using complete tractor-trailers, each in a jack-knifed position with most of the explosives placed on the ground in front of the trailer. ANFO was used in the first test to determine its response to thermal stimulus and the likelihood of detonation or explosion. The second test involved ANFO, a slurry and an emulsion. Thermocouples and video cameras were used to observe the burning characteristics of the explosives, the truck and its components. The explosives burned steadily for 80 minutes in each test. Many truck components, such as tires, spring brake chambers and the fuel tank ruptured violently due to the heat. Although no detonation occurred in the test trials, it was concluded that under favourable conditions, many truck components, might produce fragments with enough energy to initiate heat-sensitized explosives. It was suggested that a fragment impact caused the detonation at Walden. 4 refs., 7 tabs., 8 figs.

  6. Fungal Burn Wound Infection

    Science.gov (United States)

    1991-01-01

    Aspergillus), Blasto- T he use of effective topical chemotherapeutic agents to myces (Candida), and Zygomycetes ( Mucor , Rhizopus).6 reduce...species, 18%; Mucor species and Rhizopus species, acetate in the morning and silver sulfadiazine in the evening. Prophy- 9.1%; and Microspora species and...sensitivity reports, and the patient’s sue, including one patient who required a hip disarticulation response. to control an invasive Mucor burn wound

  7. Assessing burn depth in tattooed burn lesions with LASCA Imaging

    Science.gov (United States)

    Krezdorn, N.; Limbourg, A.; Paprottka, F.J.; Könneker; Ipaktchi, R.; Vogt, P.M

    2016-01-01

    Summary Tattoos are on the rise, and so are patients with tattooed burn lesions. A proper assessment with regard to burn depth is often impeded by the tattoo dye. Laser speckle contrast analysis (LASCA) is a technique that evaluates burn lesions via relative perfusion analysis. We assessed the effect of tattoo skin pigmentation on LASCA perfusion imaging in a multicolour tattooed patient. Depth of burn lesions in multi-coloured tattooed and untattooed skin was assessed using LASCA. Relative perfusion was measured in perfusion units (PU) and compared to various pigment colours, then correlated with the clinical evaluation of the lesion. Superficial partial thickness burn (SPTB) lesions showed significantly elevated perfusion units (PU) compared to normal skin; deep partial thickness burns showed decreased PU levels. PU of various tattoo pigments to normal skin showed either significantly lower values (blue, red, pink) or significantly increased values (black) whereas orange and yellow pigment showed values comparable to normal skin. In SPTB, black and blue pigment showed reduced perfusion; yellow pigment was similar to normal SPTB burn. Deep partial thickness burn (DPTB) lesions in tattoos did not show significant differences to normal DPTB lesions for black, green and red. Tattoo pigments alter the results of perfusion patterns assessed with LASCA both in normal and burned skin. Yellow pigments do not seem to interfere with LASCA assessment. However proper determination of burn depth both in SPTB and DPTB by LASCA is limited by the heterogenic alterations of the various pigment colours. PMID:28149254

  8. Burning mouth syndrome: etiology.

    Science.gov (United States)

    Cerchiari, Dafne Patrícia; de Moricz, Renata Dutra; Sanjar, Fernanda Alves; Rapoport, Priscila Bogar; Moretti, Giovana; Guerra, Marja Michelin

    2006-01-01

    The Burning Mouth Syndrome (BMS) is an oral mucosa pain--with or without inflammatory signs--without any specific lesion. It is mostly observed in women aged 40-60 years. This pain feels like a moderate/severe burning, and it occurs more frequently on the tongue, but it may also be felt at the gingiva, lips and jugal mucosa. It may worsen during the day, during stress and fatigue, when the patient speaks too much, or through eating of spicy/hot foods. The burning can be diminished with cold food, work and leisure. The goal of this review article is to consider possible BMS etiologies and join them in 4 groups to be better studied: local, systemic, emotional and idiopathic causes of pain. Knowing the different diagnoses of this syndrome, we can establish a protocol to manage these patients. Within the local pain group, we must investigate dental, allergic and infectious causes. Concerning systemic causes we need to look for connective tissue diseases, endocrine disorders, neurological diseases, nutritional deficits and salivary glands alterations that result in xerostomia. BMS etiology may be of difficult diagnosis, many times showing more than one cause for oral pain. A detailed interview, general physical examination, oral cavity and oropharynx inspection, and lab exams are essential to avoid a try and error treatment for these patients.

  9. Dual therapeutic functions of F-5 fragment in burn wounds: preventing wound progression and promoting wound healing in pigs

    Directory of Open Access Journals (Sweden)

    Ayesha Bhatia

    2016-01-01

    Full Text Available Burn injuries are a leading cause of morbidity including prolonged hospitalization, disfigurement, and disability. Currently there is no Food and Drug Administration-approved burn therapeutics. A clinical distinction of burn injuries from other acute wounds is the event of the so-called secondary burn wound progression within the first week of the injury, in which a burn expands horizontally and vertically from its initial boundary to a larger area. Therefore, an effective therapeutics for burns should show dual abilities to prevent the burn wound progression and thereafter promote burn wound healing. Herein we report that topically applied F-5 fragment of heat shock protein-90α is a dual functional agent to promote burn wound healing in pigs. First, F-5 prevents burn wound progression by protecting the surrounding cells from undergoing heat-induced caspase 3 activation and apoptosis with increased Akt activation. Accordingly, F-5–treated burn and excision wounds show a marked decline in inflammation. Thereafter, F-5 accelerates burn wound healing by stimulating the keratinocyte migration-led reepithelialization, leading to wound closure. This study addresses a topical agent that is capable of preventing burn wound progression and accelerating burn wound healing.

  10. Dual therapeutic functions of F-5 fragment in burn wounds: preventing wound progression and promoting wound healing in pigs.

    Science.gov (United States)

    Bhatia, Ayesha; O'Brien, Kathryn; Chen, Mei; Wong, Alex; Garner, Warren; Woodley, David T; Li, Wei

    2016-01-01

    Burn injuries are a leading cause of morbidity including prolonged hospitalization, disfigurement, and disability. Currently there is no Food and Drug Administration-approved burn therapeutics. A clinical distinction of burn injuries from other acute wounds is the event of the so-called secondary burn wound progression within the first week of the injury, in which a burn expands horizontally and vertically from its initial boundary to a larger area. Therefore, an effective therapeutics for burns should show dual abilities to prevent the burn wound progression and thereafter promote burn wound healing. Herein we report that topically applied F-5 fragment of heat shock protein-90α is a dual functional agent to promote burn wound healing in pigs. First, F-5 prevents burn wound progression by protecting the surrounding cells from undergoing heat-induced caspase 3 activation and apoptosis with increased Akt activation. Accordingly, F-5-treated burn and excision wounds show a marked decline in inflammation. Thereafter, F-5 accelerates burn wound healing by stimulating the keratinocyte migration-led reepithelialization, leading to wound closure. This study addresses a topical agent that is capable of preventing burn wound progression and accelerating burn wound healing.

  11. Recovery of plutonium from lean organic in presence of Ru - activity

    International Nuclear Information System (INIS)

    Govindan, P.; Vijayan, K.S.; Dhamodharan, K.; Sharma, P.K.; Desigan, N.; Mohan, S.V.; Subba Rao, R.V.

    2006-01-01

    Recovery of plutonium from the scrubbed organic by uranous stabilized with hydrazine is carried out. It is observed that the quantitative stripping of plutonium is obtained by a single contact leaving organic with 25.0 mg/L of plutonium containing 0.468mCi/L Ru activity. The retention of plutonium in the lean organic may be attributed to the presence of degradation products and ruthenium activity may be due to the stable complex of ruthenium with TBP. The final strip product almost free from ruthenium is subjected to oxalate precipitation after pre concentration.The proposed method is applied to actual plant stream during reprocessing of high burn up fuel

  12. Building Service Provider Capabilities

    DEFF Research Database (Denmark)

    Brandl, Kristin; Jaura, Manya; Ørberg Jensen, Peter D.

    2015-01-01

    In this paper we study whether and how the interaction between clients and the service providers contributes to the development of capabilities in service provider firms. In situations where such a contribution occurs, we analyze how different types of activities in the production process...... process. We find that clients influence the development of human capital capabilities and management capabilities in reciprocally produced services. While in sequential produced services clients influence the development of organizational capital capabilities and management capital capabilities....... of the services, such as sequential or reciprocal task activities, influence the development of different types of capabilities. We study five cases of offshore-outsourced knowledge-intensive business services that are distinguished according to their reciprocal or sequential task activities in their production...

  13. Faecal microbiota in lean and obese dogs.

    Science.gov (United States)

    Handl, Stefanie; German, Alexander J; Holden, Shelley L; Dowd, Scot E; Steiner, Jörg M; Heilmann, Romy M; Grant, Ryan W; Swanson, Kelly S; Suchodolski, Jan S

    2013-05-01

    Previous work has shown obesity to be associated with changes in intestinal microbiota. While obesity is common in dogs, limited information is available about the role of the intestinal microbiota. The aim of this study was to investigate whether alterations in the intestinal microbiota may be associated with canine obesity. Using 16S rRNA gene pyrosequencing and quantitative real-time PCR, we evaluated the composition of the faecal microbiota in 22 lean and 21 obese pet dogs, as well as in five research dogs fed ad libitum and four research dogs serving as lean controls. Firmicutes, Fusobacteria and Actinobacteria were the predominant bacterial phyla. The phylum Actinobacteria and the genus Roseburia were significantly more abundant in the obese pet dogs. The order Clostridiales significantly increased under ad libitum feeding in the research dogs. Canine intestinal microbiota is highly diverse and shows considerable interindividual variation. In the pet dogs, influence on the intestinal microbiota besides body condition, like age, breed, diet or lifestyle, might have masked the effect of obesity. The study population of research dogs was small, and further work is required before the role of the intestinal microbiota in canine obesity is clarified. © 2013 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

  14. Foot burns: epidemiology and management.

    Science.gov (United States)

    Hemington-Gorse, S; Pellard, S; Wilson-Jones, N; Potokar, T

    2007-12-01

    This is a retrospective study of the epidemiology and management of isolated foot burns presenting to the Welsh Centre for Burns from January 1998 to December 2002. A total of 289 were treated of which 233 were included in this study. Approximately 40% were in the paediatric age group and the gender distribution varied dramatically for adults and children. In the adult group the male:female ratio was 3.5:1, however in the paediatric group the male:female ratio was more equal (1.6:1). Scald burns (65%) formed the largest group in children and scald (35%) and chemical burns (32%) in adults. Foot burns have a complication rate of 18% and prolonged hospital stay. Complications include hypertrophic scarring, graft loss/delayed healing and wound infection. Although isolated foot burns represent a small body surface area, over half require treatment as in patients to allow for initial aggressive conservative management of elevation and regular wound cleansing to avoid complications. This study suggests a protocol for the initial acute management of foot burns. This protocol states immediate referral of all foot burns to a burn centre, admission of these burns for 24-48 h for elevation, regular wound cleansing with change of dressings and prophylactic antibiotics.

  15. A Comparison of Three Second-generation Swirl-Venturi Lean Direct Injection Combustor Concepts

    Science.gov (United States)

    Tacina, Kathleen M.; Podboy, Derek P.; He, Zhuohui Joe; Lee, Phil; Dam, Bidhan; Mongia, Hukam

    2016-01-01

    Three variations of a low emissions aircraft gas turbine engine combustion concept were developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. All three variations were based on the baseline 9- point SV-LDI configuration reported previously. The three second generation SV-LDI variations are called the 5-recess configuration, the flat dome configuration, and the 9- recess configuration. These three configurations were tested in a NASA Glenn Research Center medium pressure flametube. All three second generation variations had better low power operability than the baseline 9-point configuration. All three configurations had low NO(sub x) emissions, with the 5-recess configuration generally having slightly lower NO(x) than the flat dome or 9-recess configurations. Due to the limitations of the flametube that prevented testing at pressures above 20 atm, correlation equations were developed for the at dome and 9-recess configurations so that the landing-takeoff NO(sub x) emissions could be estimated. The flat dome and 9-recess landing-takeoff NO(x) emissions are estimated to be 81-88% below the CAEP/6 standards, exceeding the project goal of 75% reduction.

  16. A Second Generation Swirl-Venturi Lean Direct Injection Combustion Concept

    Science.gov (United States)

    Tacina, Kathleen M.; Chang, Clarence T.; He, Zhuohui Joe; Lee, Phil; Dam, Bidhan; Mongia, Hukam

    2014-01-01

    A low-NO (sub x) aircraft gas turbine engine combustion concept was developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. Three second generation SV-LDI configurations were developed. All three were based on the baseline 9-point SV-LDI configuration reported previously. These second generation configurations had better low power operability than the baseline 9-point configuration. Two of these second generation configurations were tested in a NASA Glenn Research Center flametube; these two configurations are called the at dome and 5-recess configurations. Results show that the 5-recess configuration generally had lower NO (sub x) emissions than the flat dome configuration. Correlation equations were developed for the flat dome configuration so that the landing-takeoff NO (sub x) emissions could be estimated. The flat dome landing-takeoff NO (sub x) is estimated to be 87-88 percent below the CAEP/6 standards, exceeding the ERA project goal of 75 percent reduction.

  17. Peak bone mineral density, lean body mass and fractures

    NARCIS (Netherlands)

    Boot, Annemieke M.; de Ridder, Maria A. J.; van der Sluis, Inge M.; van Slobbe, Ingrid; Krenning, Eric P.; Keizer-Schrama, Sabine M. P. F. de Muinck

    Background: During childhood and adolescence, bone mass and lean body mass (LBM) increase till a plateau is reached. In this longitudinal and cross-sectional study, the age of reaching the plateau was evaluated for lumbar spine and total body bone mass measurements and lean body mass. The

  18. Chemical structures and theoretical models of lean premixed ...

    African Journals Online (AJOL)

    To better understand the chemistry involved in the lean-fuel combustion, the chemical structure of lean premixed propene-oxygen-nitrogen flames stabilized on a flat-flame burner at atmospheric pressure was determined experimentally. The species mole fraction profiles were also computed by the Premix code and three ...

  19. Lean Supply Chain Planning: A Performance Evaluation through Simulation

    Directory of Open Access Journals (Sweden)

    Rossini Matteo

    2016-01-01

    Full Text Available Nowadays companies look more and more for improving their efficiency to excel in the market. At the same time, the competition has moved from firm level to whole supply chain level. Supply chain are very complex systems and lacks of coordination among their members leads to inefficiency. Supply chain planning task is to improve coordination among supply chain members. Which is the best planning solution to improve efficiency is an open issue. On the other hand, Lean approach is becoming more and more popular among managers. Lean approach is recognize as efficiency engine for production systems, but effects of Lean implementation out of single firm boundaries is not clear. This paper aims at providing a theoretical and practical starting point for Lean implementation in supply chain planning issue. To reach it, a DES simulation model of a three-echelon and multi-product supply chain has been set. Lean management is a very broad topic and this paper focuses on two principles of “pull” and “create the flow”. Kanban system and setup-time and batch-size reductions are implemented in the lean-configured supply chain to apply “pull” and “create the flow” respectively. Lean principles implementations have been analyzed and compared with other supply chain planning policies: EOQ and information sharing (Visibility. Supported by the simulation study, this paper points Lean supply chain planning is a competitive planning policies to increase efficiency.

  20. Benchmarking performance measurement and lean manufacturing in the rough mill

    Science.gov (United States)

    Dan Cumbo; D. Earl Kline; Matthew S. Bumgardner

    2006-01-01

    Lean manufacturing represents a set of tools and a stepwise strategy for achieving smooth, predictable product flow, maximum product flexibility, and minimum system waste. While lean manufacturing principles have been successfully applied to some components of the secondary wood products value stream (e.g., moulding, turning, assembly, and finishing), the rough mill is...

  1. Inspanning om Lean Six Sigma op kaart te zetten beloond

    NARCIS (Netherlands)

    Does, R.J.M.M.

    2008-01-01

    Prof.dr. R.J.M.M. Does is al jarenlang een fervent voorvechter voor het gebruik van statistiek. En meer recent is hij zo’n beetje de belichaming van (Lean) Six Sigma in Europa. Tal van grote organisaties hebben hem te hulp geroepen bij de invoering van (Lean) Six Sigma. Het is dan ook niet meer dan

  2. Lean Six Sigma in het ziekenhuis: De beschikbaarheid van infuuspompen

    NARCIS (Netherlands)

    Does, R.J.M.M.; Kemper, B.P.H.; Koopmans, M.

    2011-01-01

    In het topklinisch ziekenhuis Medisch Spectrum Twente werd in 2008 een Lean Six Sigma-project gestart. Het doel was vermindering van operationele kosten van infuuspompen. Het is een interessant voorbeeld van Lean Six Sigma in de gezondheidszorg, omdat het laat zien dat kostenbesparing niet hoeft te

  3. Lean and the Learning Organization in Higher Education

    Science.gov (United States)

    Francis, David E.

    2014-01-01

    Canadian post-secondary institutions are seeking enhanced efficiencies due to ongoing funding shortfalls and expanding teaching, research, and service mandates. These institutions have considered or enacted Lean methodology based on results reported by public service and healthcare organizations worldwide. Lean requires a high level of…

  4. The productive operating theatre and lean thinking systems.

    Science.gov (United States)

    Kasivisvanathan, R; Chekairi, A

    2014-11-01

    The concept of 'lean thinking' first originated in the manufacturing industry as a means of improving productivity whilst maintaining quality through eliminating wasteful processes. The purpose of this article is to demonstrate how the principles of 'lean thinking' are relevant to healthcare and the operating theatre, with reference to our own institutional experience.

  5. Lean Thinking in Systems with Non-Negligible Process Variability

    DEFF Research Database (Denmark)

    Nielsen, Erland Hejn; Simons, David

    2000-01-01

    Lean Thinking (Womack and Jones) improves quality, cost and delivery through the relentless elimination of the wastes. For example, the exemplar of Lean, the Toyota Production system, focuses on improvement through the continual elimination of seven categorised wastes (Ohno). Time compression (St...

  6. Lean Thinking in systems with non-negligible process variability

    DEFF Research Database (Denmark)

    Nielsen, Erland Hejn; Simons, David

    2000-01-01

    Lean Thinking (Womack and Jones) improves quality, cost and delivery through the relentless elimination of wastes. For example, the exemplar of Lean, the Toyota Production system, focuses on improvement through the continual elimination of seven categorised wastes (Ohno). Time compression (Stalk ...

  7. Lang vej endnu før bilindustrien er Lean

    DEFF Research Database (Denmark)

    Christiansen, Thomas Bøhm

    2005-01-01

    Anmeldelse og diskussion af bogen "The Second Century: Reconnecting Customer and Value Chain through Build-to-order - Moving beyond Mass and Lean Production in the Auto Industry......Anmeldelse og diskussion af bogen "The Second Century: Reconnecting Customer and Value Chain through Build-to-order - Moving beyond Mass and Lean Production in the Auto Industry...

  8. Logistics services and Lean Six Sigma implementation: a case study

    NARCIS (Netherlands)

    Gutierrez Gutierrez, L.; de Leeuw, S.L.J.M.; Dubbers, R.

    2016-01-01

    Purpose: This paper aims to analyze the application of Lean Six Sigma (LSS) framework for supporting continuous improvement (CI) in logistics services. Both the lean philosophy and the Six Sigma methodology have become two of the most important initiatives for CI in organizations. The combination of

  9. An application of Lean Six Sigma in a hospital

    NARCIS (Netherlands)

    van den Heuvel, J.; Does, R.J.M.M.; de Koning, H.; Anthony, J.; Kumar, M.

    2007-01-01

    Abstract Healthcare today faces major challenges. Patients demand quality of care to be improved continuously. Insurance companies demand the lowest possible prices. Lean Six Sigma is a tool that can help healthcare providers to achieve these at least partly conflicting goals. Lean Six Sigma is an

  10. Agile and lean principles and systems engineering: a synergy?

    CSIR Research Space (South Africa)

    Joseph-Malherbe, SM

    2011-09-01

    Full Text Available not efficient and effective enough to support rapid fielding of products. The objective of this piece of work is multi-fold: (1) to explore and present fundamental Systems Engineering, Agile and Lean principles (2) the evolution or lack of Lean and Agile...

  11. Yalın düşünce ve Muhasebe (Lean Thinking and Accounting

    Directory of Open Access Journals (Sweden)

    Baki Rıza BALCI

    2011-01-01

    Full Text Available The aim of this article is to introduce the relationship between Lean Thinking and Accounting. It is explained in detail the kinds of reports generated when Lean Thinking implemented in accounting.It is identified that accounting, which could not keep pace with Lean Transformation and remain traditional, shares the failures of companies, who went Lean. This article emphasize that the companies that want to transform themselves into Lean, have to generate proper reports that suit Lean transformation. The types of reports are explained.Literature was scanned and some sample reports are submitted to the Turkish companies that want to go Lean and successful in their Lean efforts.

  12. Lean manufacturing: A better way for enhancement in productivity

    Science.gov (United States)

    Kumar Ahir, Pankaj; Kumar Yadav, Lalit; Singh Chandrawat, Saurabh

    2012-03-01

    Productivity is the impact of peoples working together. Machines are merely an extended way of collective imagination and energy. Lean Manufacturing is the most used method for continues improvement of business. Organization management philosophy focusing on the reduction of wastage to improve overall customer value. "Lean" operating principles began in manufacturing environments and are known by a variety of synonyms; Lean Manufacturing, Lean Production, Toyota Production System, etc. It is commonly believed that Lean started in Japan "The notable activities in keeping the price of Ford products low is the steady restriction of the production cycle. The longer an article is in the process of manufacture and the more it is moved about, the greater is its ultimate cost." "A systematic approach to identifying and eliminating waste through continuous improvement, flowing the product at the pull of the customer in pursuit of perfection."

  13. Is there a lean future for global startups?

    DEFF Research Database (Denmark)

    Tanev, Stoyan

    2017-01-01

    This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on gl......-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.......This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing...... on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology...

  14. Lean principles applied to software development – avoiding waste

    Directory of Open Access Journals (Sweden)

    Ionel NAFTANAILA

    2009-12-01

    Full Text Available Under the current economic conditions many organizations strive to continue the trend towards adopting better software development processes, in order to take advantage of the numerous benefits that these can offer. Those benefits include quicker return on investment, better software quality, and higher customer satisfaction. To date, however, there is little body of research that can guide organizations in adopting modern software development practices, especially when it comes to Lean thinking and principles. To address this situation, the current paper identifies and structures the main wastes (or muda in Lean terms in software development as described by Lean principles, in an attempt to bring into researchers’ and practitioners’ attention Lean Software Development, a modern development methodology based on well-established practices such as Lean Manufacturing or Toyota Production System.

  15. The lean product design and development journey a practical view

    CERN Document Server

    Pessôa, Marcus Vinicius Pereira

    2017-01-01

    This book presents a series of high performance product design (PD) and development best practices that can create or improve product development organization. In contrast to other books that focus only on Toyota or other individual companies applying lean IPD, this book explains the lean philosophy more broadly and includes discussions of systems engineering, design for X (DFX), agile development, integrated product development, and project management. The “Lean Journey” proposed here takes a value-centric approach, where the lean principles are applied to PD to allow the tools and methods selected to emerge from observation of the individual characteristics of each enterprise. This means that understanding lean product development (LPD) is not about knowing which tools are available but knowing how to apply the philosophy. The book comes with an accompanying manual with problems and solutions available on Springer Extras.

  16. LEAN THINKING IN HEALTHCARE: REVIEW OF IMPLEMENTATION RESULTS

    Directory of Open Access Journals (Sweden)

    Marija Kovacevic

    2016-03-01

    Full Text Available For over decade, automotive industry originated lean concept has been successfully implemented in healthcare systems as a management method and philosophy with main focus on elimination of all types of wastes and looses in all tasks and processes so that time, materials, resources and medical procedures could be realized as effectively as it is possible. As main result lean concept implementation ensured to healthcare organizations to focus on their main core function and dedicate more time and efforts to patients without additional costs for them or healthcare system. However, lean implementation in healthcare could be much more difficult than in standard industrial environment and there are significant number of examples of lean in healthcare projects that failed to gain any measurable results and sustainable benefits from it. This paper presents review of some of the most successful implementations of lean tools and principles in healthcare organizations.

  17. Individualisation of Lean Concept in Companies Dealing with Mass Production

    Science.gov (United States)

    Bednár, Roman

    2012-12-01

    The methods of lean manufacturing primarily designed for businesses dealing with serial production, are also used in other types of production. However the concept of lean production was not designed for these types of businesses, they are utilized only partially. Paper focuses on applying methods of lean concept in companies which are dealing with mass production and their options of exchange for other methods in the event of disagreement. Basis of the article is a list of lean methods with its description and its utilization in practice. The questionnaire was utilized to identify information from the practice. Based on this survey were identified the critical methods that are no longer appropriate for companies dealing with mass production. However, there are alternative methods of describing the problem. It is possible to say that companies are trying to get closer to their goal by modification of the basic concepts. And the concept of Lean Enterprise serves as a standard.

  18. The application of lean principles in product development

    DEFF Research Database (Denmark)

    Bjarnø, Ole-Christian

    2007-01-01

    Although Lean Manufacturing has been a megatrend for several years, its principles have not been broadly applied in product development processes. We have therefore found it useful to look into the theories of lean manufacturing and to discuss how and to what extent they could be applied in the p......Although Lean Manufacturing has been a megatrend for several years, its principles have not been broadly applied in product development processes. We have therefore found it useful to look into the theories of lean manufacturing and to discuss how and to what extent they could be applied...... in the product development processes, and this study is compared with industrial practices in several front running companies in Denmark. From this research a suggestion for a framework and a tool-box for lean product development is created and discussed from a HR management, an implementation, an operational...

  19. The Role of Molecule Clustering by Hydrogen Bond in Hydrous Ethanol on Laminar Burning Velocity

    Directory of Open Access Journals (Sweden)

    I Made Suarta

    2016-01-01

    Full Text Available The role of hydrogen bond molecule clustering in laminar burning velocities was observed. The water in hydrous ethanol can change the interaction between water-ethanol molecules. A certain amount of water can become oxygenated which increases the burning velocity. The hydrogen bond interaction pattern of ethanol and water molecules was modeled. Based on the molecular model, azeotropic behavior emerges from ethanol-water hydrogen bond, which is at a 95.1%v composition. The interaction with water molecule causes the ethanol molecule to be clustered with centered oxygenated compound. So, it supplies extra oxygen and provides intermolecular empty spaces that are easily infiltrated by the air. In the azeotropic composition, the molecular bond chain is the shortest, so hypothetically the burning velocity is anticipated to increase. The laminar burning velocity of ethanol fuel was tested in a cylindrical explosion bomb in lean, stoichiometric, and rich mixtures. The experimental result showed that the maximum burning velocity occurred at hydrous ethanol of 95.5%v composition. This discrepancy is the result of the addition of energy from 7.7% free ethanol molecules that are not clustered. At the rich mixture, the burning velocity of this composition is higher than that of anhydrous ethanol.

  20. Community integration after burn injuries.

    Science.gov (United States)

    Esselman, P C; Ptacek, J T; Kowalske, K; Cromes, G F; deLateur, B J; Engrav, L H

    2001-01-01

    Evaluation of community integration is a meaningful outcome criterion after major burn injury. The Community Integration Questionnaire (CIQ) was administered to 463 individuals with major burn injuries. The CIQ results in Total, Home Integration, Social Integration, and Productivity scores. The purposes of this study were to determine change in CIQ scores over time and what burn injury and demographic factors predict CIQ scores. The CIQ scores did not change significantly from 6 to 12 to 24 months postburn injury. Home integration scores were best predicted by sex and living situation; Social Integration scores by marital status; and Productivity scores by functional outcome, burn severity, age, and preburn work factors. The data demonstrate that individuals with burn injuries have significant difficulties with community integration due to burn and nonburn related factors. CIQ scores did not improve over time but improvement may have occurred before the initial 6-month postburn injury follow-up in this study.

  1. Capability Handbook- offline metrology

    DEFF Research Database (Denmark)

    Islam, Aminul; Marhöfer, David Maximilian; Tosello, Guido

    This offline metrological capability handbook has been made in relation to HiMicro Task 3.3. The purpose of this document is to assess the metrological capability of the HiMicro partners and to gather the information of all available metrological instruments in the one single document. It provides...

  2. Dynamic Capabilities and Performance

    DEFF Research Database (Denmark)

    Wilden, Ralf; Gudergan, Siegfried P.; Nielsen, Bo Bernhard

    2013-01-01

    are contingent on the competitive intensity faced by firms. Our findings demonstrate the performance effects of internal alignment between organizational structure and dynamic capabilities, as well as the external fit of dynamic capabilities with competitive intensity. We outline the advantages of PLS...

  3. Developing Alliance Capabilities

    DEFF Research Database (Denmark)

    Heimeriks, Koen H.; Duysters, Geert; Vanhaverbeke, Wim

    This paper assesses the differential performance effects of learning mechanisms on the development of alliance capabilities. Prior research has suggested that different capability levels could be identified in which specific intra-firm learning mechanisms are used to enhance a firm's alliance...

  4. Telematics Options and Capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, Cabell [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-05

    This presentation describes the data tracking and analytical capabilities of telematics devices. Federal fleet managers can use the systems to keep their drivers safe, maintain a fuel efficient fleet, ease their reporting burden, and save money. The presentation includes an example of how much these capabilities can save fleets.

  5. Serum Predictors of Percent Lean Mass in Young Adults.

    Science.gov (United States)

    Lustgarten, Michael S; Price, Lori L; Phillips, Edward M; Kirn, Dylan R; Mills, John; Fielding, Roger A

    2016-08-01

    Lustgarten, MS, Price, LL, Phillips, EM, Kirn, DR, Mills, J, and Fielding, RA. Serum predictors of percent lean mass in young adults. J Strength Cond Res 30(8): 2194-2201, 2016-Elevated lean (skeletal muscle) mass is associated with increased muscle strength and anaerobic exercise performance, whereas low levels of lean mass are associated with insulin resistance and sarcopenia. Therefore, studies aimed at obtaining an improved understanding of mechanisms related to the quantity of lean mass are of interest. Percent lean mass (total lean mass/body weight × 100) in 77 young subjects (18-35 years) was measured with dual-energy x-ray absorptiometry. Twenty analytes and 296 metabolites were evaluated with the use of the standard chemistry screen and mass spectrometry-based metabolomic profiling, respectively. Sex-adjusted multivariable linear regression was used to determine serum analytes and metabolites significantly (p ≤ 0.05 and q ≤ 0.30) associated with the percent lean mass. Two enzymes (alkaline phosphatase and serum glutamate oxaloacetate aminotransferase) and 29 metabolites were found to be significantly associated with the percent lean mass, including metabolites related to microbial metabolism, uremia, inflammation, oxidative stress, branched-chain amino acid metabolism, insulin sensitivity, glycerolipid metabolism, and xenobiotics. Use of sex-adjusted stepwise regression to obtain a final covariate predictor model identified the combination of 5 analytes and metabolites as overall predictors of the percent lean mass (model R = 82.5%). Collectively, these data suggest that a complex interplay of various metabolic processes underlies the maintenance of lean mass in young healthy adults.

  6. A One-Dimensional Global-Scaling Erosive Burning Model Informed by Blowing Wall Turbulence

    Science.gov (United States)

    Kibbey, Timothy P.

    2014-01-01

    A derivation of turbulent flow parameters, combined with data from erosive burning test motors and blowing wall tests results in erosive burning model candidates useful in one-dimensional internal ballistics analysis capable of scaling across wide ranges of motor size. The real-time burn rate data comes from three test campaigns of subscale segmented solid rocket motors tested at two facilities. The flow theory admits the important effect of the blowing wall on the turbulent friction coefficient by using blowing wall data to determine the blowing wall friction coefficient. The erosive burning behavior of full-scale motors is now predicted more closely than with other recent models.

  7. Lean IT partnering : How partners create value by developing a lean culture for IT supply and management

    NARCIS (Netherlands)

    Zee, van der J.T.M.; Blijleven, V.B; Gong, Y.

    2015-01-01

    Lean, as a philosophy, has been around for quite some time, predominantly in the manufacturing domain. Since the 1990s Lean management provides organizations with a way to achieve superior performance by focusing on customer value, innovation and productivity. In 2011 Steven Bell and Michael Orzen

  8. Burning Mouth Syndrome

    OpenAIRE

    Renton, Tara

    2011-01-01

    Bruning mouth syndrome is a burning sensation of one or several oral soft tissues with the tongue being affected the most, and may be associated with some other symptoms outside the oral structures. The oral symptoms may appear suddenly or gradually within a time course, may be persistent throughout the day or get more intense as the day progresses in a complaint-free patient in the morning. The syndrome affects mostly women and those over 50 years old, and usually caused by multiple factors....

  9. Burning mouth syndrome: An update

    OpenAIRE

    Vijay Kumar Ambaldhage; Jaishankar Homberhalli Puttabuddi; Purnachandrarao Naik Nunsavath

    2015-01-01

    Burning mouth syndrome (BMS) is characterized by an oral burning sensation in the absence of any organic disorders of the oral cavity. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. It is observed principally in middle-aged patients and postmenopausal women and is characterized by an intense burning type of pain, preferably on the tongue and in other areas of the ...

  10. Burning mouth syndrome: Present perspective

    OpenAIRE

    Ramesh Parajuli

    2015-01-01

    Introduction: Burning mouth syndrome is characterized by chronic oral pain or burning sensation affecting the oral mucosa in the absence of obvious visible mucosal lesions. Patient presenting with the burning mouth sensation or pain is frequently encountered in clinical practice which poses a challenge to the treating clinician. Its exact etiology remains unknown which probably has multifactorial origin. It often affects middle or old age women and it may be accompanied by xerostomia and alte...

  11. Effects of different duration exercise programs in children with severe burns.

    Science.gov (United States)

    Clayton, Robert P; Wurzer, Paul; Andersen, Clark R; Mlcak, Ronald P; Herndon, David N; Suman, Oscar E

    2017-06-01

    Burns lead to persistent and detrimental muscle breakdown and weakness. Standard treatment at our institution includes a voluntary 12-week rehabilitative exercise program to limit and reverse the effects of increased muscle catabolism. In the present work, we investigated if different durations of exercise, 6 or 12 weeks, produce comparable improvements in muscle strength, body composition, and cardiopulmonary fitness. We prospectively enrolled and randomized patients with ≥30% total body surface area (TBSA) burned to receive 6 or 12 weeks of exercise rehabilitation. Patients were evaluated for muscle strength, oxygen consumption capacity, and lean body mass at discharge (n=42) and after exercise. After 6 weeks (n=18) or 12 weeks (n=24) of exercise training, leg muscle strength was assessed as peak torque per body weight using a Biodex isokinetic dynamometer. Oxygen consumption capacity, measured as peak VO 2 , was studied using a standard treadmill-based test, and lean body mass was determined using dual-energy X-ray absorptiometry. Significant improvements in muscle strength, peak VO 2 , and lean body mass were seen after 6 weeks of exercise training (pburn patients. However, continuation of at- or near-home cardiopulmonary training following the 6 weeks of at-hospital rehabilitation may be useful. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

  12. Ice & Fire: the Burning Question

    DEFF Research Database (Denmark)

    van Gelderen, Laurens; Jomaas, Grunde

    2017-01-01

    With the Arctic opening up to new shipping routes and increased oil exploration and production due to climate change, the risk of an Arctic oil spill is increasing. Of the classic oil spill response methods (mechanical recovery, dispersants and in-situ burning), in-situ burning is considered...... to be particularly a suitable response method in the Arctic. In-situ burning aims to remove the oil from the marine environment by burning it from the water surface. A recent Ph.D. thesis from the Technical University of Denmark has provided some new insights with respect to the fire science behind this response...

  13. An experimental study of a hydrogen-enriched ethanol fueled Wankel rotary engine at ultra lean and full load conditions

    International Nuclear Information System (INIS)

    Amrouche, F.; Erickson, P.A.; Varnhagen, S.; Park, J.W.

    2016-01-01

    Highlights: • H_2 was added at the intake of a single-rotor ethanol fueled Wankel engine. • The engine was operating at ultra-lean condition, WOT and 3000 rpm. • H_2 enrichment helps shortening the burn duration, enhance the thermal efficiency and reduce the BSEC. • H_2 addition helps to reduce HC, CO and CO_2 emissions. - Abstract: In this paper, the effect of hydrogen addition to ethanol in a monorotor Wankel engine at wide open throttle position and in an ultra-lean operating regime was experimentally investigated. For this aim, variation of hydrogen enrichment levels on the ethanol engine performance and emissions were considered. Experiments were carried out under a constant engine speed of 3000 rpm and fixed spark timing of 15 °BTDC. The test results showed that hydrogen enrichment improved the combustion process through shortening of the flame development and flame propagation periods and reducing the cyclic variation. Furthermore, the reduction of burn duration with the increase of hydrogen fraction enhances the thermal efficiency, reducing the brake-specific energy consumption, as well as reducing the unburned hydrocarbons emissions of the Wankel engine.

  14. Novel burn device for rapid, reproducible burn wound generation.

    Science.gov (United States)

    Kim, J Y; Dunham, D M; Supp, D M; Sen, C K; Powell, H M

    2016-03-01

    Scarring following full thickness burns leads to significant reductions in range of motion and quality of life for burn patients. To effectively study scar development and the efficacy of anti-scarring treatments in a large animal model (female red Duroc pigs), reproducible, uniform, full-thickness, burn wounds are needed to reduce variability in observed results that occur with burn depth. Prior studies have proposed that initial temperature of the burner, contact time with skin, thermal capacity of burner material, and the amount of pressure applied to the skin need to be strictly controlled to ensure reproducibility. The purpose of this study was to develop a new burner that enables temperature and pressure to be digitally controlled and monitored in real-time throughout burn wound creation and compare it to a standard burn device. A custom burn device was manufactured with an electrically heated burn stylus and a temperature control feedback loop via an electronic microstat. Pressure monitoring was controlled by incorporation of a digital scale into the device, which measured downward force. The standard device was comprised of a heat resistant handle with a long rod connected to the burn stylus, which was heated using a hot plate. To quantify skin surface temperature and internal stylus temperature as a function of contact time, the burners were heated to the target temperature (200±5°C) and pressed into the skin for 40s to create the thermal injuries. Time to reach target temperature and elapsed time between burns were recorded. In addition, each unit was evaluated for reproducibility within and across three independent users by generating burn wounds at contact times spanning from 5 to 40s at a constant pressure and at pressures of 1 or 3lbs with a constant contact time of 40s. Biopsies were collected for histological analysis and burn depth quantification using digital image analysis (ImageJ). The custom burn device maintained both its internal

  15. Lean practices for quality results: a case illustration.

    Science.gov (United States)

    Hwang, Pauline; Hwang, David; Hong, Paul

    2014-01-01

    Increasingly, healthcare providers are implementing lean practices to achieve quality results. Implementing lean healthcare practices is unique compared to manufacturing and other service industries. The purpose of this paper is to present a model that identifies and defines the lean implementation key success factors in healthcare organisations. The model is based on an extant literature review and a case illustration that explores actual lean implementation in a major USA hospital located in a Midwestern city (approximately 300,000 people). An exploratory/descriptive study using observation and follow-up interviews was conducted to identify lean practices in the hospital. Lean practice key drivers include growing elderly populations, rising medical expenses, decreasing insurance coverage and decreasing management support. Effectively implementing lean practices to increase bottom-line results and improve organisational integrity requires sharing goals and processes among healthcare managers and professionals. An illustration explains the model and the study provides a sound foundation for empirical work. Practical implications are included. Lean practices minimise waste and unnecessary hospital stays while simultaneously enhancing customer values and deploying resources in supply systems. Leadership requires clear project targets based on sound front-end planning because initial implementation steps involve uncertainty and ambiguity (i.e. fuzzy front-end planning). Since top management support is crucial for implementing lean practices successfully, a heavyweight manager, who communicates well both with top managers and project team members, is an important success factor when implementing lean practices. Increasingly, green orientation and sustainability initiatives are phrases that replaced lean practices. Effective results; e.g. waste reduction, employee satisfaction and customer values are applicable to bigger competitive challenges arising both in specific

  16. Lean and global technology start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being...... global and innovative at the same time should be seen as one process. The paper has two components – an introductory conceptual part and an empirical part that should be considered as basis for the preliminary validation of the conceptual insights. The research sample includes six firms – three from...... Canada and three from Denmark. The firms have had significant problems with the complexity, uncertainties and risks of being innovative on a global scale. They have however found ways of addressing these problems by a disciplined knowledge sharing and IP protection strategy and the efficient use...

  17. Lean construction management the Toyota way

    CERN Document Server

    Gao, Shang

    2014-01-01

    The book presents a mixed research method adopted to assess and present the Toyota Way practices within construction firms in general and for firms in China specifically. The results of an extensive structured questionnaire survey based on the Toyota Way-styled attributes identified were developed, and data collected from building professionals working in construction firms is presented. The quantitative data presented in the book explains the status quo of the Toyota Way-styled practices implemented in the construction industry, as well as the extent to which these attributes were perceived for lean construction management. The book highlights all the actionable attributes derived from the Toyota Way model appreciated by the building professionals, but alerts the readers that some attributes felled short of implementation. Further findings from in-depth interviews and case studies are also presented in the book to provide to readers an understanding how these Toyota Way practices can be implemented in real-l...

  18. The role of outsourcing in Lean Manufacturing

    DEFF Research Database (Denmark)

    Bjarnø, Ole-Christian

    2003-01-01

    In this article a longitudinal study performed at a medium-sized producer of electronics is reported during which we studied the company’s manufacturing change process. Based on theories of outsourcing, reengineering and explorative case research a series of findings is identified which demonstra......In this article a longitudinal study performed at a medium-sized producer of electronics is reported during which we studied the company’s manufacturing change process. Based on theories of outsourcing, reengineering and explorative case research a series of findings is identified which...... degree of complexity by introducing many new product lines, without phasing out very many of the old products could be changed into a far less complex organisation through reengineering and outsourcing. This again opened up for the application of the tool kit in Lean Manufacturing, and through...

  19. Oral Rehydration Therapy in Burn Patients

    Science.gov (United States)

    2014-04-24

    Burn Any Degree Involving 20-29 Percent of Body Surface; Burn Any Degree Involving 30-39 Percent of Body Surface; Burn Any Degree Involving 40-49 Percent of Body Surface; Burn Any Degree Involving 50-59 Percent of Body Surface; Burn Any Degree Involving 60-65 Percent of Body Surface

  20. FMEF/experimental capabilities

    International Nuclear Information System (INIS)

    Burgess, C.A.; Dronen, V.R.

    1981-01-01

    The Fuels and Materials Examination Facility (FMEF), under construction at the Hanford site north of Richland, Washington, will be one of the most modern facilities offering irradiated fuels and materials examination capabilities and fuel fabrication development technologies. Scheduled for completion in 1984, the FMEF will provide examination capability for fuel assemblies, fuel pins and test pins irradiated in the FFTF. Various functions of the FMEF are described, with emphasis on experimental data-gathering capabilities in the facility's Nondestructive and Destructive examination cell complex

  1. KSC Technical Capabilities Website

    Science.gov (United States)

    Nufer, Brian; Bursian, Henry; Brown, Laurette L.

    2010-01-01

    This document is the website pages that review the technical capabilities that the Kennedy Space Center (KSC) has for partnership opportunities. The purpose of this information is to make prospective customers aware of the capabilities and provide an opportunity to form relationships with the experts at KSC. The technical capabilities fall into these areas: (1) Ground Operations and Processing Services, (2) Design and Analysis Solutions, (3) Command and Control Systems / Services, (4) Materials and Processes, (5) Research and Technology Development and (6) Laboratories, Shops and Test Facilities.

  2. Global Burned Area and Biomass Burning Emissions from Small Fires

    Science.gov (United States)

    Randerson, J. T.; Chen, Y.; vanderWerf, G. R.; Rogers, B. M.; Morton, D. C.

    2012-01-01

    In several biomes, including croplands, wooded savannas, and tropical forests, many small fires occur each year that are well below the detection limit of the current generation of global burned area products derived from moderate resolution surface reflectance imagery. Although these fires often generate thermal anomalies that can be detected by satellites, their contributions to burned area and carbon fluxes have not been systematically quantified across different regions and continents. Here we developed a preliminary method for combining 1-km thermal anomalies (active fires) and 500 m burned area observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) to estimate the influence of these fires. In our approach, we calculated the number of active fires inside and outside of 500 m burn scars derived from reflectance data. We estimated small fire burned area by computing the difference normalized burn ratio (dNBR) for these two sets of active fires and then combining these observations with other information. In a final step, we used the Global Fire Emissions Database version 3 (GFED3) biogeochemical model to estimate the impact of these fires on biomass burning emissions. We found that the spatial distribution of active fires and 500 m burned areas were in close agreement in ecosystems that experience large fires, including savannas across southern Africa and Australia and boreal forests in North America and Eurasia. In other areas, however, we observed many active fires outside of burned area perimeters. Fire radiative power was lower for this class of active fires. Small fires substantially increased burned area in several continental-scale regions, including Equatorial Asia (157%), Central America (143%), and Southeast Asia (90%) during 2001-2010. Globally, accounting for small fires increased total burned area by approximately by 35%, from 345 Mha/yr to 464 Mha/yr. A formal quantification of uncertainties was not possible, but sensitivity

  3. The challenges of lean manufacturing implementation in kitting assembly

    Science.gov (United States)

    Fansuri, A. F. H.; Rose, A. N. M.; Nik Mohamed, N. M. Z.; Ahmad, H.

    2017-10-01

    Literature studies shows that lean manufacturing goes way back with the original founder Eli Whitney in year 1799. The main purpose of lean manufacturing is to identify and eliminate waste in production. The application of lean manufacturing can be carried out in any industrial processes with regards to the understanding of lean principles, theories and practices. Kitting is one of the important aspects in a successful production. The continuous supply of materials from store to production has to be systematic and able to achieve lean standard for it to be successful. The objective of this paper is to review the implementation of lean manufacturing in kitting assembly. Previous papers show that, the implementation of lean manufacturing in kitting assembly may be beneficial to the organization such as reduce in space occupancy, part shortages, lead time and manpower. Based on previous research, some industries may tend to change between kitting and line stocking which are due to lack of understanding when implementing kitting and causes longer lead time and materials overflow in store. With a proper understanding on what to kit, where to kit, how to kit, why to kit and who kits the material with a standardised process flow may ensure the success of kitting.

  4. Lean implementation strategies: how are the Toyota way principles addressed?

    Directory of Open Access Journals (Sweden)

    Coetzee, Rojanette

    2016-11-01

    Full Text Available Lean manufacturing is widely considered to be a proven organisational improvement philosophy, yet the success rate of lean implementation in industry remains relatively low. Neglect of the human aspect of lean manufacturing is often cited as the leading reason for this, despite the emphasis so clearly placed upon this aspect by the creators of the lean philosophy. This article reviews the extent to which the human dimensions of the lean philosophy, as described in the Toyota Way management principles, have been incorporated in lean implementation strategies. It is found that few of the principles feature prominently in these strategies. Notably absent are those linked to the ‘respect for people’ pillar , which forms half of the T oyota Way’s foundation. This conclusion indicates that the adoption of the lean philosophy runs contrary to the oft-repeated message from its creators that no tenet of the philosophy should be favoured at the expense of another. This may provide valuable insight into the reasons for the high implementation failure rate.

  5. Medical and scientific writing: Time to go lean and mean

    Directory of Open Access Journals (Sweden)

    Payal Bhardwaj

    2017-01-01

    Full Text Available The Lean Six Sigma methodology for process improvements and driving efficiency is old, but lean writing was adopted late by the pharmaceutical world in terms of size of the documents. The documents were lean earlier, and then became voluminous, and now we are about to complete a full circle in this regard, i.e., coming back to the lean documents again using e-formats and hyperlinking. Furthermore, writing has become more and more precise over time. The need for this lean and mean medical and scientific writing arose from voluminous research globally, both industry and academia which are abuzz with skyrocketing regulatory and scientific submission volumes. The quantum of literature is so much that reviewers or information seekers firmly believe that going through even selected and relevant literature has become highly challenging. Considering this, there has been much insistence on downsizing the medical writing documents, which could be tempting enough to be leveraged for scientific publications as well. Here, we present the need for lean and mean medical writing, discuss this concept in relation to the pharmaceutical industry, and how to apply this to key documents. Furthermore, presented is the proposed algorithm for lean and mean clinical study reports and manuscripts. These thoughts are aligned to the recently established concept of data transparency, and can be easily achieved by web links between the protocols and clinical trial results disclosed publicly, and the corresponding manuscripts.

  6. Improvement of emergency department patient flow using lean thinking.

    Science.gov (United States)

    Sánchez, Miquel; Suárez, Montse; Asenjo, María; Bragulat, Ernest

    2018-05-01

    To apply lean thinking in triage acuity level-3 patients in order to improve emergency department (ED) throughtput and waiting time. A prospective interventional study. An ED of a tertiary care hospital. Triage acuity level-3 patients. To apply lean techniques such as value stream mapping, workplace organization, reduction of wastes and standardization by the frontline staff. Two periods were compared: (i) pre-lean: April-September, 2015; and (ii) post-lean: April-September, 2016. Variables included: median process time (time from beginning of nurse preparation to the end of nurse finalization after doctor disposition) of both discharged and transferred to observation patients; median length of stay; median waiting time; left without being seen, 72-h revisit and mortality rates, and daily number of visits. There was no additional staff or bed after lean implementation. Despite an increment in the daily number of visits (+8.3%, P lean implementation. No significant differences were registered in left without being seen rate (5.23% vs 4.95%), 72-h revisit rate (3.41% vs 3.93%), and mortality rate (0.23% vs 0.15%). Lean thinking is a methodology that can improve triage acuity level-3 patient flow in the ED, resulting in better throughput along with reduced waiting time.

  7. Lean og professionel autonomi på hospitaler

    DEFF Research Database (Denmark)

    Hasle, Peter

    2014-01-01

    Hospitaler står overfor store udfordringer fra voksende krav fra både patienter og samfund samtidig med begrænsede budgetter og stadig flere medicinske muligheder. Hospitalsledelserne anvender lean som en af de væsentligste metoder til at løse disse udfordringer. Lean stammer imidlertid fra...... industrien, og det er spørgsmålet, hvordan lean bliver tilpasset i til en hospitalssammenhæng, og hvilke konsekvenser lean får for medarbejderne. Dette spørgsmål er undersøgt i forbindelse med introduktion af lean i en kræftafdeling på et universitetshospital. Det viste sig vanskeligere end forventet...... at implementere lean, og konsekvenserne for henholdsvis laboranter og sygeplejersker viste sig at være meget forskelligartede. Laboranterne oplevede et forbedret arbejdsmiljø, mens det modsatte var tilfældet for sygeplejerskerne. En mulig forklaring er, at lean øgede kontrollen over eget arbejde for laboranterne...

  8. In-situ burning of Orimulsion : small scale burns

    International Nuclear Information System (INIS)

    Fingas, M.F.

    2002-01-01

    This study examined the feasibility of burning Orimulsion. In-situ burning has always been a viable method for cleaning oil spills on water because it can effectively reduce the amount of spilled oil and eliminate the need to collect, store, transport and dispose of recovered oil. Orimulsion, however, behaves very differently from conventional oil when it is spilled because of its composition of 70 per cent bitumen in 30 per cent water. In-situ burning of this surfactant-stablized oil-in-water emulsion has never been seriously considered because of the perception that Orimulsion could not be ignited, and if it could, ignition would not be sustained. In this study, burn tests were conducted on 3 scales in a Cleveland Open Cup apparatus of 5 cm, 10 cm and 50 cm diameters. Larger scale burns were conducted in specially built pans. All tests were conducted on salt water which caused the bitumen to separate from the water. The objective was to determine if sufficient vapours could be generated to ignite the Orimulsion. The study also measured if a sustained flame would result in successful combustion. Both objectives were successfully accomplished. Diesel fuel was used to ignite the Orimulsion in the specially designed pan for large scale combustion. Quantitative removal of Orimulsion was achieved in all cases, but in some burns it was necessary to re-ignite the Orimulsion. It was noted that when Orimulsion burns, some trapped water droplets in the bitumen explode with enough force to extinguish a small flame. This did not occur on large-scale burns. It was concluded that the potential for successful in-situ burning increases with size. It was determined that approximately 1 mm in thickness of diesel fuel is needed to ignite a burn. 5 refs., 3 tabs., 4 figs

  9. Resources, constraints and capabilities

    NARCIS (Netherlands)

    Dhondt, S.; Oeij, P.R.A.; Schröder, A.

    2018-01-01

    Human and financial resources as well as organisational capabilities are needed to overcome the manifold constraints social innovators are facing. To unlock the potential of social innovation for the whole society new (social) innovation friendly environments and new governance structures

  10. a Capability approach

    African Journals Online (AJOL)

    efforts towards gender equality in education as a means of achieving social justice. ... should mean that a lot of capability approach-oriented commentators are ... processes, their forms of exercising power, and their rules, unwritten cultures, ...

  11. Engineering Capabilities and Partnerships

    Science.gov (United States)

    Poulos, Steve

    2010-01-01

    This slide presentation reviews the engineering capabilities at Johnson Space Center, The presentation also reviews the partnerships that have resulted in successfully designed and developed projects that involved commercial and educational institutions.

  12. Brandishing Cyberattack Capabilities

    Science.gov (United States)

    2013-01-01

    Advertising cyberwar capabilities may be helpful. It may back up a deterrence strategy. It might dissuade other states from conventional mischief or...to enable the attack.5 Many of the instruments of the attack remain with the target system, nestled in its log files, or even in the malware itself...debat- able. Even if demonstrated, what worked yesterday may not work today. But difficult does not mean impossible. Advertising cyberwar capabilities

  13. CASL Dakota Capabilities Summary

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Brian M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Simmons, Chris [Univ. of Texas, Austin, TX (United States); Williams, Brian J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-10

    The Dakota software project serves the mission of Sandia National Laboratories and supports a worldwide user community by delivering state-of-the-art research and robust, usable software for optimization and uncertainty quantification. These capabilities enable advanced exploration and riskinformed prediction with a wide range of computational science and engineering models. Dakota is the verification and validation (V&V) / uncertainty quantification (UQ) software delivery vehicle for CASL, allowing analysts across focus areas to apply these capabilities to myriad nuclear engineering analyses.

  14. Acceptance of lean redesigns in primary care: A contextual analysis.

    Science.gov (United States)

    Hung, Dorothy; Gray, Caroline; Martinez, Meghan; Schmittdiel, Julie; Harrison, Michael I

    Lean is a leading change strategy used in health care to achieve short-term efficiency and quality improvement while promising longer-term system transformation. Most research examines Lean intervention to address isolated problems, rather than to achieve broader systemic changes to care delivery. Moreover, no studies examine contextual influences on system-wide Lean implementation efforts in primary care. The aim of this study was to identify contextual factors most critical to implementing and scaling Lean redesigns across all primary care clinics in a large, ambulatory care delivery system. Over 100 interviews and focus groups were conducted with frontline physicians, clinical staff, and operational leaders. Data analysis was guided by a modified Consolidated Framework for Implementation Research (CFIR), a popular implementation science framework. On the basis of expert recommendations, the modified framework targets factors influencing the implementation of process redesigns. This modified framework, the CFIR-PR, informed our identification of contextual factors that most impacted Lean acceptance among frontline physicians and staff. Several domains identified by the CFIR-PR were critical to acceptance of Lean redesigns. Regarding the implementation process acceptance was influenced by time and intensity of exposure to changes, "top-down" versus "bottom-up" implementation styles, and degrees of employee engagement in developing new workflows. Important factors in the inner setting were the clinic's culture and style of leadership, along with availability of information about Lean's effectiveness. Last, implementation efforts were impacted by individual and team characteristics regarding changed work roles and related issues of professional identity, authority, and autonomy. This study underscores the need for change leaders to consider the contextual factors that surround efforts to implement Lean in primary care. As Lean redesigns are scaled across a system

  15. 30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

  16. Pollutant Formation during the Occurrence of Flame Instabilities under Very-Lean Combustion Conditions in a Liquid-Fuel Burner

    Directory of Open Access Journals (Sweden)

    Maria Grazia De Giorgi

    2017-03-01

    Full Text Available Recent advances in gas turbine combustor design are aimed at achieving low exhaust emissions, hence modern aircraft jet engines are designed with lean-burn combustion systems. In the present work, we report an experimental study on lean combustion in a liquid fuel burner, operated under a non-premixed (single point injection regime that mimics the combustion in a modern aircraft engine. The flame behavior was investigated in proximity of the blow-out limit by an intensified high rate Charge-Coupled Device (CCD camera equipped with different optical filters to selectively record single species chemiluminescence emissions (e.g., OH*, CH*. Analogous filters were also used in combination with photomultiplier (PMT tubes. Furthermore this work investigates well-mixed lean low NOx combustion where mixing is good and generation of solid carbon particulate emissions should be very low. An analysis of pollutants such as fine particles and gaseous emissions was also performed. Particle number concentrations and size distributions were measured at the exhaust of the combustion chamber by two different particle size measuring instruments: a scanning mobility particle sizer (SMPS and an Electrical Low Pressure Impactor (ELPI. NOx concentration measurements were performed by using a cross-flow modulation chemiluminescence detection system; CO concentration emissions were acquired with a Cross-flow modulation Non-dispersive infrared (NDIR absorption method. All the measurements were completed by diagnostics of the fundamental combustor parameters. The results herein presented show that at very-lean conditions the emissions of both particulate matter and CO was found to increase most likely due to the occurrence of flame instabilities while the NOx were observed to reduce.

  17. Animal Models in Burn Research

    Science.gov (United States)

    Abdullahi, A.; Amini-Nik, S.; Jeschke, M.G

    2014-01-01

    Burn injury is a severe form of trauma affecting more than two million people in North America each year. Burn trauma is not a single pathophysiological event but a devastating injury that causes structural and functional deficits in numerous organ systems. Due to its complexity and the involvement of multiple organs, in vitro experiments cannot capture this complexity nor address the pathophysiology. In the past two decades, a number of burn animal models have been developed to replicate the various aspects of burn injury; to elucidate the pathophysiology and explore potential treatment interventions. Understanding the advantages and limitations of these animal models is essential for the design and development of treatments that are clinically relevant to humans. This review paper aims to highlight the common animal models of burn injury in order to provide investigators with a better understanding of the benefits and limitations of these models for translational applications. While many animal models of burn exist, we limit our discussion to the skin healing of mouse, rat, and pig. Additionally, we briefly explain hypermetabolic characteristics of burn injury and the animal model utilized to study this phenomena. Finally, we discuss the economic costs associated with each of these models in order to guide decisions of choosing the appropriate animal model for burn research. PMID:24714880

  18. Stem Cells in Burn Eschar

    NARCIS (Netherlands)

    van der Veen, V. C.; Vlig, M.; van Milligen-Kummer, F.J.; de Vries, S.I.; Middelkoop, E.; Ulrich, M.

    2012-01-01

    This study compares mesenchymal cells isolated from excised burn wound eschar with adipose-derived stem cells (ASCs) and dermal fibroblasts in their ability to conform to the requirements for multipotent mesenchymal stem cells (MSCs). A population of multipotent stem cells in burn eschar could be an

  19. Lean production teams and health in garment manufacture.

    Science.gov (United States)

    Jackson, P R; Mullarkey, S

    2000-04-01

    The impact of lean production on psychological health was assessed by comparing lean production teams in garment manufacture with a traditional system for making similar garments. Work design characteristics were examined as mediators of the impact of work organization on health. Findings indicate both positive and negative direct effects of teamworking on aspects of autonomy, work demands, and social climate. In turn, both positive and negative direct effects of work design on psychological health were found, which combine to give no overall difference between the groups. This study suggests that the balance between positive and negative effects of lean production teamworking depends on management choices in the form of work design.

  20. Implementation analysis of lean enablers for managing engineering programs

    DEFF Research Database (Denmark)

    von Arnim, Joachim; Oehmen, Josef; Rebentisch, Eric

    2014-01-01

    This paper presents research to improve the applicability of the Lean Enablers and consists of two parts. The first is a case study of a very successful project management maturity improvement initiative at Siemens Industry Sector’s Industry Automation division in the US. It views the initiative...... from the perspective of the Lean Enablers [Oehmen 2012] and is based on information from [Sopko 2012a], [Sopko 2012b], [Sopko 2010], [Sopko 2009], interviews, internal documentation, and the used MSP program management methodology [UK 2011]. The analysis of Lean Enablers incorporated in the MSP...

  1. Lean Manufacturing Implementation: an Approach to Reduce Production Cost

    Directory of Open Access Journals (Sweden)

    Iraswari

    2012-04-01

    Full Text Available Abstract: Lean Manufacturing Implementation: An Approach To Reduce Production Cost. Opportunities to improve production processes and reduce production cost through the implementation of lean manufacturing in small medium garment manufacturing are presented in this research. This research shows that there is a possibility of decrease in production cost and increase in return on sales. Lean manufacturing implementation can eliminate waste in the production process. This is a set of techniques for identification and elimination of waste gathered from The Ford Production, Statistical Process Control and other techniques. Improvement of quality could be carried out while time and cost of production are being reduced.

  2. Lean Management as an Instrument of Sustainable Development of Enterprises

    Science.gov (United States)

    Sikora, Marcin; Kwiatkowski, Maciej; Prosół, Hanna; Nowicka, Daria; Lorenc, Karolina; Pham, Laurena

    2016-03-01

    The aim of the paper is to present the philosophy of Lean Management as an instrument of improving sustainable management of enterprises. The article presents the origins, characteristics of the broadly understood concept of Lean Management and describes the idea of Sustainable Development (SD). At the same time implications for the application and development of the instruments which operationalize the assumptions of SD at the level of enterprises are discussed. The paper specifies those areas of functioning of contemporary companies in which Lean Management can be implemented and compares them with the features of traditional management in particular subjects.

  3. Burning mouth syndrome: An update

    Directory of Open Access Journals (Sweden)

    Vijay Kumar Ambaldhage

    2015-01-01

    Full Text Available Burning mouth syndrome (BMS is characterized by an oral burning sensation in the absence of any organic disorders of the oral cavity. Although the cause of BMS is not known, a complex association of biological and psychological factors has been identified, suggesting the existence of a multifactorial etiology. It is observed principally in middle-aged patients and postmenopausal women and is characterized by an intense burning type of pain, preferably on the tongue and in other areas of the oral mucosa. As the symptom of oral burning is seen in various pathological conditions, it is essential for a clinician to be aware of how to differentiate between symptom of oral burning and BMS. This article provides an overview of the literature on this syndrome with special reference to the etiological factors, clinical aspects, diagnostic criteria that should be followed and the therapeutic management with reference to the most recent studies.

  4. Fuel burning and climate

    International Nuclear Information System (INIS)

    Aunan, Kristin

    2004-01-01

    Emission of soot particles and other air pollution indoors constitutes a considerable health hazard for a major part of the population in many developing countries, one of them being China. In these countries problems relating to poverty are the most important risk factors, undernourishment being the dominating reason. Number four on the list of the most serious health hazards is indoor air pollution caused by burning of coal and biomass in the households. Very high levels of soot particles occur indoors because of incomplete combustion in old-fashioned stoves and by use of low quality fuel such as sticks and twigs and straw and other waste from agriculture. This leads to an increase in a series of acute and chronic respiratory diseases, including lung cancer. It has been pointed out in recent years that emissions due to incomplete combustion of coal and biomass can contribute considerably to climate changes

  5. Space Logistics: Launch Capabilities

    Science.gov (United States)

    Furnas, Randall B.

    1989-01-01

    The current maximum launch capability for the United States are shown. The predicted Earth-to-orbit requirements for the United States are presented. Contrasting the two indicates the strong National need for a major increase in Earth-to-orbit lift capability. Approximate weights for planned payloads are shown. NASA is studying the following options to meet the need for a new heavy-lift capability by mid to late 1990's: (1) Shuttle-C for near term (include growth versions); and (2) the Advanced Lauching System (ALS) for the long term. The current baseline two-engine Shuttle-C has a 15 x 82 ft payload bay and an expected lift capability of 82,000 lb to Low Earth Orbit. Several options are being considered which have expanded diameter payload bays. A three-engine Shuttle-C with an expected lift of 145,000 lb to LEO is being evaluated as well. The Advanced Launch System (ALS) is a potential joint development between the Air Force and NASA. This program is focused toward long-term launch requirements, specifically beyond the year 2000. The basic approach is to develop a family of vehicles with the same high reliability as the Shuttle system, yet offering a much greater lift capability at a greatly reduced cost (per pound of payload). The ALS unmanned family of vehicles will provide a low end lift capability equivalent to Titan IV, and a high end lift capability greater than the Soviet Energia if requirements for such a high-end vehicle are defined.In conclusion, the planning of the next generation space telescope should not be constrained to the current launch vehicles. New vehicle designs will be driven by the needs of anticipated heavy users.

  6. Pediatric burns: Kids' Inpatient Database vs the National Burn Repository.

    Science.gov (United States)

    Soleimani, Tahereh; Evans, Tyler A; Sood, Rajiv; Hartman, Brett C; Hadad, Ivan; Tholpady, Sunil S

    2016-04-01

    Burn injuries are one of the leading causes of morbidity and mortality in young children. The Kids' Inpatient Database (KID) and National Burn Repository (NBR) are two large national databases that can be used to evaluate outcomes and help quality improvement in burn care. Differences in the design of the KID and NBR could lead to differing results affecting resultant conclusions and quality improvement programs. This study was designed to validate the use of KID for burn epidemiologic studies, as an adjunct to the NBR. Using the KID (2003, 2006, and 2009), a total of 17,300 nonelective burn patients younger than 20 y old were identified. Data from 13,828 similar patients were collected from the NBR. Outcome variables were compared between the two databases. Comparisons revealed similar patient distribution by gender, race, and burn size. Inhalation injury was more common among the NBR patients and was associated with increased mortality. The rates of respiratory failure, wound infection, cellulitis, sepsis, and urinary tract infection were higher in the KID. Multiple regression analysis adjusting for potential confounders demonstrated similar mortality rate but significantly longer length of stay for patients in the NBR. Despite differences in the design and sampling of the KID and NBR, the overall demographic and mortality results are similar. The differences in complication rate and length of stay should be explored by further studies to clarify underlying causes. Investigations into these differences should also better inform strategies to improve burn prevention and treatment. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Lean Manufacturing e Lean Accounting Cost: um enfoque no real desempenho em empresas de capital aberto na BOVESPA

    OpenAIRE

    Teixeira, Hipólito Francisco

    2016-01-01

    Esta pesquisa teve por alvo o campo de estudo denominado Lean Accounting (LA) aplicado as empresas que adotam os procedimentos de Produção Enxuta (PE). As empresas neste ambiente competitivo e muito imprevisivel têm procuradoadotar decisões e procedimentos voltadosa valorizar sua própria continuidade e diferencial para se expor perante ao mercado. Neste sentido novas tecnologias de produção e controles contábeis são necessários. Lean Accounting (LA) ou Contabilidade Lean ou “enxuta” pode s...

  8. Campus Capability Plan

    Energy Technology Data Exchange (ETDEWEB)

    Adams, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Arsenlis, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bergman, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brase, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brenner, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Camara, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Carlton, H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cheng, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chrzanowski, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Colson, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); East, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Farrell, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ferranti, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gursahani, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hansen, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Helms, L. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hernandez, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jeffries, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Larson, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lu, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McNabb, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mercer, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Skeate, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sueksdorf, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zucca, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Le, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ancria, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Scott, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Leininger, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gagliardi, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gash, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bronson, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chung, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hobson, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Meeker, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sanchez, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zagar, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Quivey, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sommer, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Atherton, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-06-06

    Lawrence Livermore National Laboratory Campus Capability Plan for 2018-2028. Lawrence Livermore National Laboratory (LLNL) is one of three national laboratories that are part of the National Nuclear Security Administration. LLNL provides critical expertise to strengthen U.S. security through development and application of world-class science and technology that: Ensures the safety, reliability, and performance of the U.S. nuclear weapons stockpile; Promotes international nuclear safety and nonproliferation; Reduces global danger from weapons of mass destruction; Supports U.S. leadership in science and technology. Essential to the execution and continued advancement of these mission areas are responsive infrastructure capabilities. This report showcases each LLNL capability area and describes the mission, science, and technology efforts enabled by LLNL infrastructure, as well as future infrastructure plans.

  9. Technological Capability's Predictor Variables

    Directory of Open Access Journals (Sweden)

    Fernanda Maciel Reichert

    2011-03-01

    Full Text Available The aim of this study was to identify the factors that influence in configuration of the technological capability of companies in sectors with medium-low technological intensity. To achieve the goal proposed in this article a survey was carried out. Based on the framework developed by Lall (1992 which classifies firms in basic, intermediate and advanced level of technological capability; it was found that the predominant technological capability is intermediate, with 83.7% of respondent companies (plastics companies in Brazil. It is believed that the main contribution of this study is the finding that the dependent variable named “Technological Capability” can be explained at a rate of 65% by six variables: development of new processes; selection of the best equipment supplier; sales of internally developed new technology to third parties; design and manufacture of equipment; study of the work methods and perform inventory control; and improvement of product quality.

  10. Lean and the working environment: a review of the literature

    DEFF Research Database (Denmark)

    Hasle, Peter; Bojesen, Anders; Jensen, Per Langaa

    2012-01-01

    for the negative impact of lean on both the working environment and employee health and well-being in cases of manual work with low complexity. However, since examples of positive effects were also found in the literature, it is important to move from a simple cause-and-effect model to a more comprehensive model...... of manufacturing industry. The literature reflects, only to a limited extent, on the significance of implementation strategy and production context. Practical implications - Organizations working with lean should make efforts to avoid an impaired working environment for manual employees. Involvement of employees......Purpose - The effects of lean on employees have been debated ever since the concept was introduced. The purpose of this paper is to review the scientific literature on the effects of lean on the working environment and employee health and well-being. Design/methodology/approach - Relevant databases...

  11. The Effects of Application of Lean Concept in Retail

    Directory of Open Access Journals (Sweden)

    Radojko LUKIC

    2012-06-01

    Full Text Available Lean principles and techniques can be successfully applied in the retail sector. In the retail sector, lean approach improves operational flows. Lean retail encourages manufacturers to produce standard products in accordance with the created (placed orders from retailers pursuant to the demand of their consumers. Characteristics of the retail market are: strong competition, shorter product life cycle, longer product development time and high sensitivity of demand. In order to be more competitive and profitable today's retailers operate strategically oriented to lower prices and gain exemption from holding unnecessary stocks. Lean retail is an example of best practices of successful operational strategies which management need to accept - to maximize the operating efficiency of the retail process.

  12. Succesful Lean Manufacturing Implementation: Internal Key Influencing Factors

    Science.gov (United States)

    Virginia, Iuga; Claudiu, Kifor

    2015-09-01

    Manufacturing sectors and companies all over the world are successfully implementing lean principles within their processes. Nowadays, lean has become an indispensable part of global players. Companies worldwide need to be aware of multiple factors which weigh heavily on the success or failure of lean implementation. This paper focuses on giving a brief and structured overview over the fundamental organizational factors which play a substantial role for the lean manufacturing (LM) implementation process. The study below focuses on internal factors which are indispensable for a successful LM implementation within organizations. It is imperative that these internal factors are known, recognized and taken into consideration during the whole LM implementation process. Ignoring their influence on the process's implementation may lead to endangering the expected results or to making the process more difficult which could result in much higher human resource consumption.

  13. Implications of Lean Manufacturing for Human Resource Strategy.

    Science.gov (United States)

    Forrester, Rosalind

    1995-01-01

    Lean production changes organizational style and structure, roles of team leaders and members, training needs, problem-solving approaches, labor relations, and pay practices. The profound cultural changes it causes may trigger defenses that cause it to fail. (SK)

  14. Establishing a Lean Six Sigma Program in Higher Education

    KAUST Repository

    Svensson, Carsten; Baessa, Mohamed A.; Bakhsh, Majed M.

    2013-01-01

    Purpose: The objective of this paper is a contribution to the body of Lean Six Sigma knowledge within the vertical of higher education institutions. The paper will review the initial phase of an implementation and highlight future challenges. Approach: The observations presented in this paper, originates from rolling out a large lean six sigma implementation at a newly established university. The paper is supported with secondary data from literature. Findings: The paper will discuss the challenges of applying the lean six sigma method in a complex transactional environment. Research limitations: This paper is based on an empirical study of a single instance and authors’ experiences as practitioners. Originality: This paper is the first description of what is believed to be one of the largest implementations of Lean Six Sigma in higher education.

  15. Lean Manufacturing, Mass Customization and their relationships - empirical findings

    DEFF Research Database (Denmark)

    Christiansen, Thomas Bøhm

    2004-01-01

    manufacturing companies in 2001-02. This study fills a void in existing research by exploring relationships between bundles of lean manufacturing practices and bundles of mass customization practices. This study is based on a questionnaire that is developed from two existing questionnaires each investigating...... bundles of lean manufacturing practices and bundles of mass customization practices separately. Here, these bundles of practices are related. The results indicate that there are no direct relationships between the lean manufacturing and the mass customization practices, but that the combination of some...... sets of practices can explain differences in performance on important dimensions. The general conclusion, however, is that there are only weak relationships between the two concepts, hence this study suggests that the concepts of lean manufacturing and mass customization at present are more mutually...

  16. Thermal Radiation Properties of Turbulent Lean Premixed Methane Air Flames

    National Research Council Canada - National Science Library

    Ji, Jun; Sivathanu, Y. R; Gore, J. P

    2000-01-01

    ... of turbulent premixed flames. Reduced cooling airflows in lean premixed combustors, miniaturization of combustors, and the possible use of radiation sensors in combustion control schemes are some of the practical reasons...

  17. Lean six sigma case studies in the healthcare enterprise

    CERN Document Server

    Furterer, Sandra L

    2014-01-01

    This book provides a detailed description of how to apply Lean Six Sigma in the health care industry, with a special emphasis on process improvement and operations management in hospitals.  The book begins with a description of the Enterprise Performance Excellence (EPE) improvement methodology developed by the author that links several methodologies including systems thinking, theory of constraints, Lean and Six Sigma to provide an enterprise-wide prioritization and value-chain view of health care. The EPE methodology helps to improve flow at the macro or value-chain level, and then identifies Lean Six Sigma detailed improvements that can further improve processes within the value-chain.  The book also provides real-world health care applications of the EPE and Lean Six Sigma methodologies that showed significant results on throughput, capacity, operational and financial performance. The Enterprise Performance Excellence methodology is described, and also the Six Sigma DMAIC (Define-Measure-Analyze-Improve...

  18. Quality and Competitiveness: A Lean Six Sigma Approach

    Directory of Open Access Journals (Sweden)

    Irina-Virginia Drăgulănescu

    2015-11-01

    Full Text Available Originally developed to improve the quality and production efficiency, Lean Six Sigma is now widely adopted in other non-manufacturing sectors such as financial, trade, services, etc. The methodology known as Lean Six Sigma combines the Six Sigma techniques, ‒ which allow companies to reduce manufacturing defects ‒ and the Lean Manufacturing principles, ‒ which help companies benefit from faster processing for lower costs and with superior quality. As a result of the research, the authors observed that, despite growing popularity and impressive outcomes obtained by some companies, the Lean Six Sigma model does not always offer the expected results. However, the research has shown that the analysed company, operating in the field of courier services has managed to boost productivity and competitiveness by implementing measures that generated added value.

  19. LEAN BODY MASS AS A PREDICTOR OF PERFORMANCE OF ...

    African Journals Online (AJOL)

    siahkohian

    literature indicates considerable variations in the LBM of different athletes, with values ranging from a ... Olympic weightlifters are related to and predictive of indirect estimates of absolute and ... Lean body mass & weightlifter performance. 181.

  20. Establishing a Lean Six Sigma Program in Higher Education

    KAUST Repository

    Svensson, Carsten

    2013-09-12

    Purpose: The objective of this paper is a contribution to the body of Lean Six Sigma knowledge within the vertical of higher education institutions. The paper will review the initial phase of an implementation and highlight future challenges. Approach: The observations presented in this paper, originates from rolling out a large lean six sigma implementation at a newly established university. The paper is supported with secondary data from literature. Findings: The paper will discuss the challenges of applying the lean six sigma method in a complex transactional environment. Research limitations: This paper is based on an empirical study of a single instance and authors’ experiences as practitioners. Originality: This paper is the first description of what is believed to be one of the largest implementations of Lean Six Sigma in higher education.